Discrepancies between leg-to-leg bioelectrical Impedance analysis and computerized tomography in abdominal visceral fat measurement.

PubMed

Lu, Hsueh-Kuan; Chen, Yu-Yawn; Yeh, Chinagwen; Chuang, Chih-Lin; Chiang, Li-Ming; Lai, Chung-Liang; Casebolt, Kevin M; Huang, Ai-Chun; Lin, Wen-Long; Hsieh, Kuen-Chang

2017-08-22

The aim of this study was to evaluate leg-to-leg bioelectrical impedance analysis (LBIA) using a four-contact electrode system for measuring abdominal visceral fat area (VFA). The present study recruited 381 (240 male and 141 female) Chinese participants to compare VFA measurements estimated by a standing LBIA system (VFALBIA) with computerized tomography (CT) scanned at the L4-L5 vertebrae (VFA CT ). The total mean body mass index (BMI) was 24.7 ± 4.2 kg/m 2 . Correlation analysis, regression analysis, Bland-Altman plot, and paired sample t-tests were used to analyze the accuracy of the VFA LBIA . For the total subjects, the regression line was VFA LBIA  = 0.698 VFA CT  + 29.521, (correlation coefficient (r) = 0.789, standard estimate of error (SEE) = 24.470 cm 2 , p < 0.001), Lin's correlation coefficient (CCC) was 0.785; and the limit of agreement (LOA; mean difference ±2 standard deviation) ranged from -43.950 to 67.951 cm 2 , LOA% (given as a percentage of mean value measured by the CT) was 48.2%. VFA LBIA and VFA CT showed significant difference (p < 0.001). Collectively, the current study indicates that LBIA has limited potential to accurately estimate visceral fat in a clinical setting.

Rumen modulatory effect of thyme, clove and peppermint oils in vitro using buffalo rumen liquor.

PubMed

Roy, Debashis; Tomar, S K; Kumar, Vinod

2015-02-01

The present study was conducted to examine the rumen modulatory effect of thyme, clove and peppermint oils on rumen fermentation pattern in vitro using roughage based diet. Thyme, clove and peppermint oils were tested at concentration of 0, 30, 300 and 600 mg/l (ppm) of total culture fluid using in vitro gas production technique in wheat straw based diet (concentrate: Wheat straw 50:50). Different in vitro parameters e.g., total gas production, methane production, nutrient degradability, volatile fatty acid (VFA) production and ammonia nitrogen concentration were studied using buffalo rumen liquor. Thyme oil at higher dose level (600 ppm) reduced (p<0.05) total gas production, feed degradability and ammonia nitrogen (NH3-N) concentration whereas total VFA concentration was significantly lower (p>0.05) in 300 and 600 ppm dose levels. 600 ppm dose level of clove oil reduced (p<0.05) total gas production, feed degradability, total VFA and acetate to propionate ratio. Methane production was significantly reduced (p<0.05) in 300 and 600 ppm dose levels of clove and peppermint oil. Right combination of these essential oils may prove to enhance performance of animals by reducing methane production and inhibiting protein degradation in rumen.

The Associations Between Smoking Habits and Serum Triglyceride or Hemoglobin A1c Levels Differ According to Visceral Fat Accumulation.

PubMed

Koda, Michiko; Kitamura, Itsuko; Okura, Tomohiro; Otsuka, Rei; Ando, Fujiko; Shimokata, Hiroshi

2016-01-01

Whether smokers and former smokers have worse lipid profiles or glucose levels than non-smokers remains unclear. The subjects were 1152 Japanese males aged 42 to 81 years. The subjects were divided according to their smoking habits (nonsmokers, former smokers, and current smokers) and their visceral fat area (VFA) (<100 cm(2) and ≥100 cm(2)). The serum triglyceride (TG) levels of 835 males were assessed. In the VFA ≥100 cm(2) group, a significantly greater proportion of current smokers (47.3%) exhibited TG levels of ≥150 mg/dL compared with former smokers (36.4%) and non-smokers (18.8%). The difference in TG level distribution between former smokers and non-smokers was also significant. However, among the subjects with VFA of <100 cm(2), the TG levels of the three smoking habit groups did not differ. The serum hemoglobin A1c (HbA1c) levels of 877 males were also assessed. In the VFA <100 cm(2) group, significantly higher proportions of current smokers (17.9%) and former smokers (14.9%) demonstrated HbA1c levels of ≥5.6% compared with non-smokers (6.3%). In contrast, in the VFA ≥100 cm(2) group, significantly fewer former smokers displayed HbA1c levels of ≥5.6% compared with non-smokers and current smokers. Furthermore, the interaction between smoking habits and VFA was associated with the subjects' TG and HbA1c concentrations, and the associations of TG and HbA1c concentrations and smoking habits varied according to VFA. Both smoking habits and VFA exhibited associations with TG and HbA1c concentrations. The associations between smoking habits and these parameters differed according to VFA.

Waste activated sludge fermentation: effect of solids retention time and biomass concentration.

PubMed

Yuan, Q; Sparling, R; Oleszkiewicz, J A

2009-12-01

Laboratory scale, room temperature, semi-continuous reactors were set-up to investigate the effect of solids retention time (SRT, equal to HRT hydraulic retention time) and biomass concentration on generation of volatile fatty acids (VFA) from the non-methanogenic fermentation of waste activated sludge (WAS) originating from an enhanced biological phosphorus removal process. It was found that VFA yields increased with SRT. At the longest SRT (10d), improved biomass degradation resulted in the highest soluble to total COD ratio and the highest VFA yield from the influent COD (0.14g VFA-COD/g TCOD). It was also observed that under the same SRT, VFA yields increased when the biomass concentration decreased. At a 10d SRT the VFA yield increased by 46%, when the biomass concentration decreased from 13g/L to 4.8g/L. Relatively high nutrient release was observed during fermentation. The average phosphorus release was 17.3mg PO(4)-P/g TCOD and nitrogen release was 25.8mg NH(4)-N/g TCOD.

Electrolytic extraction drives volatile fatty acid chain elongation through lactic acid and replaces chemical pH control in thin stillage fermentation.

PubMed

Andersen, Stephen J; Candry, Pieter; Basadre, Thais; Khor, Way Cern; Roume, Hugo; Hernandez-Sanabria, Emma; Coma, Marta; Rabaey, Korneel

2015-01-01

Volatile fatty acids (VFA) are building blocks for the chemical industry. Sustainable, biological production is constrained by production and recovery costs, including the need for intensive pH correction. Membrane electrolysis has been developed as an in situ extraction technology tailored to the direct recovery of VFA from fermentation while stabilizing acidogenesis without caustic addition. A current applied across an anion exchange membrane reduces the fermentation broth (catholyte, water reduction: H2O + e(-) → ½ H2 + OH(-)) and drives carboxylate ions into a clean, concentrated VFA stream (anolyte, water oxidation: H2O → 2e(-) + 2 H(+) + O2). In this study, we fermented thin stillage to generate a mixed VFA extract without chemical pH control. Membrane electrolysis (0.1 A, 3.22 ± 0.60 V) extracted 28 ± 6 % of carboxylates generated per day (on a carbon basis) and completely replaced caustic control of pH, with no impact on the total carboxylate production amount or rate. Hydrogen generated from the applied current shifted the fermentation outcome from predominantly C2 and C3 VFA (64 ± 3 % of the total VFA present in the control) to majority of C4 to C6 (70 ± 12 % in the experiment), with identical proportions in the VFA acid extract. A strain related to Megasphaera elsdenii (maximum abundance of 57 %), a bacteria capable of producing mid-chain VFA at a high rate, was enriched by the applied current, alongside a stable community of Lactobacillus spp. (10 %), enabling chain elongation of VFA through lactic acid. A conversion of 30 ± 5 % VFA produced per sCOD fed (60 ± 10 % of the reactive fraction) was achieved, with a 50 ± 6 % reduction in suspended solids likely by electro-coagulation. VFA can be extracted directly from a fermentation broth by membrane electrolysis. The electrolytic water reduction products are utilized in the fermentation: OH(-) is used for pH control without added chemicals, and H2 is metabolized by species such as Megasphaera elsdenii to produce greater value, more reduced VFA. Electro-fermentation displays promise for generating added value chemical co-products from biorefinery sidestreams and wastes.

Higher visceral fat area increases the risk of vitamin D insufficiency and deficiency in Chinese adults.

PubMed

Zhang, Meilin; Li, Ping; Zhu, Yufeng; Chang, Hong; Wang, Xuan; Liu, Weiqiao; Zhang, Yuwen; Huang, Guowei

2015-01-01

Visceral fat area (VFA), a novel sex-specific index for visceral fat obesity (VFO) might play a major role in the development of vitamin D deficiency. However, the association between VFA and vitamin D insufficiency and deficiency in Chinese population is less clear. The aim of this study was to explore the population-level association between VFA and vitamin D insufficiency and deficiency among Chinese men and women. This cross-sectional study involved 1105 adults aged 20-70 years living in Tianjin who were randomly selected and medically examined. All subjects underwent the bioelectrical impedance analysis (BIA) method to estimate the VFA. Serum 25-hydroxyvitamin D3 (25(OH) D3) level was assayed by the high-performance liquid chromatography (HPLC) method and defined insufficiency and deficiency following recommended cutoffs. The association between VFA and vitamin D insufficiency and deficiency was estimated using binary regression analysis. The total prevalence of vitamin D insufficiency (25(OH) D3: 20-29 μg/L) and deficiency (25(OH) D3 < 20 μg/L) were 26.60 % and 24.89 %, respectively. Significant negative association was observed for VFA with serum 25(OH) D3 levels in men and pre-menopausal women (P < 0.05), not in post-menopausal women (P > 0.05). Moreover, increased VFA was observed to be associated with higher vitamin D insufficiency or deficiency risk with a positive dose-response trend (P for trend < 0.001). As compared to individuals with the lowest VFA, those who had the highest VFA were at 4.9-fold risk of vitamin D insufficiency and deficiency [95 % confidence interval (95 % CI): 1.792-13.365] in men and 1.8-fold risk of vitamin D insufficiency and deficiency (95 % CI: 1.051-3.210) in pre-menopausal women, but not in post-menopausal women [odds ratio (OR) (95 % CI): 2.326(0.903-5.991)]. These results suggest that higher VFA increases the risk of vitamin D insufficiency and deficiency in men and pre-menopausal women, but not in post-menopausal women. VFA is a better and convenience surrogate marker for visceral adipose measurement and could be used in identifying the risk of vitamin D insufficiency and deficiency in routine health examination.

Quantitative Gd-DOTA uptake from cerebrospinal fluid into rat brain using 3D VFA-SPGR at 9.4T.

PubMed

Lee, Hedok; Mortensen, Kristian; Sanggaard, Simon; Koch, Palle; Brunner, Hans; Quistorff, Bjørn; Nedergaard, Maiken; Benveniste, Helene

2018-03-01

We propose a quantitative technique to assess solute uptake into the brain parenchyma based on dynamic contrast-enhanced MRI (DCE-MRI). With this approach, a small molecular weight paramagnetic contrast agent (Gd-DOTA) is infused in the cerebral spinal fluid (CSF) and whole brain gadolinium concentration maps are derived. We implemented a 3D variable flip angle spoiled gradient echo (VFA-SPGR) longitudinal relaxation time (T1) technique, the accuracy of which was cross-validated by way of inversion recovery rapid acquisition with relaxation enhancement (IR-RARE) using phantoms. Normal Wistar rats underwent Gd-DOTA infusion into CSF via the cisterna magna and continuous MRI for approximately 130 min using T1-weighted imaging. Dynamic Gd-DOTA concentration maps were calculated and parenchymal uptake was estimated. In the phantom study, T1 discrepancies between the VFA-SPGR and IR-RARE sequences were approximately 6% with a transmit coil inhomogeneity correction. In the in vivo study, contrast transport profiles indicated maximal parenchymal retention of approximately 19% relative to the total amount delivered into the cisterna magna. Imaging strategies for accurate 3D contrast concentration mapping at 9.4T were developed and whole brain dynamic concentration maps were derived to study solute transport via the glymphatic system. The newly developed approach will enable future quantitative studies of the glymphatic system in health and disease states. Magn Reson Med 79:1568-1578, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Effect of geometrical parameters on pressure distributions of impulse manufacturing technologies

NASA Astrophysics Data System (ADS)

Brune, Ryan Carl

Impulse manufacturing techniques constitute a growing field of methods that utilize high-intensity pressure events to conduct useful mechanical operations. As interest in applying this technology continues to grow, greater understanding must be achieved with respect to output pressure events in both magnitude and distribution. In order to address this need, a novel pressure measurement has been developed called the Profile Indentation Pressure Evaluation (PIPE) method that systematically analyzes indentation patterns created with impulse events. Correlation with quasi-static test data and use of software-assisted analysis techniques allows for colorized pressure maps to be generated for both electromagnetic and vaporizing foil actuator (VFA) impulse forming events. Development of this technique aided introduction of a design method for electromagnetic path actuator systems, where key geometrical variables are considered using a newly developed analysis method, which is called the Path Actuator Proximal Array (PAPA) pressure model. This model considers key current distribution and proximity effects and interprets generated pressure by considering the adjacent conductor surfaces as proximal arrays of individual conductors. According to PIPE output pressure analysis, the PAPA model provides a reliable prediction of generated pressure for path actuator systems as local geometry is changed. Associated mechanical calculations allow for pressure requirements to be calculated for shearing, flanging, and hemming operations, providing a design process for such cases. Additionally, geometry effect is investigated through a formability enhancement study using VFA metalworking techniques. A conical die assembly is utilized with both VFA high velocity and traditional quasi-static test methods on varied Hasek-type sample geometries to elicit strain states consistent with different locations on a forming limit diagram. Digital image correlation techniques are utilized to measure major and minor strains for each sample type to compare limit strain results. Overall testing indicated decreased formability at high velocity for 304 DDQ stainless steel and increased formability at high velocity for 3003-H14 aluminum. Microstructural and fractographic analysis helped dissect and analyze the observed differences in these cases. Overall, these studies comprehensively explore the effects of geometrical parameters on magnitude and distribution of impulse manufacturing generated pressure, establishing key guidelines and models for continued development and implementation in commercial applications.

Total volatile fatty acid concentrations are unreliable estimators of treatment effects on ruminal fermentation in vivo

USDA-ARS?s Scientific Manuscript database

Volatile fatty acid concentrations ([VFA], mM) have long been used to assess impact of dietary treatments on ruminal fermentation in vivo. However, discrepancies in statistical results between VFA and VFA pool size (VFAmol), possibly related to ruminal digesta liquid amount (LIQ, kg), suggest issues...

Formate, acetate, and propionate as substrates for sulfate reduction in sub-arctic sediments of Southwest Greenland

PubMed Central

Glombitza, Clemens; Jaussi, Marion; Røy, Hans; Seidenkrantz, Marit-Solveig; Lomstein, Bente A.; Jørgensen, Bo B.

2015-01-01

Volatile fatty acids (VFAs) are key intermediates in the anaerobic mineralization of organic matter in marine sediments. We studied the role of VFAs in the carbon and energy turnover in the sulfate reduction zone of sediments from the sub-arctic Godthåbsfjord (SW Greenland) and the adjacent continental shelf in the NE Labrador Sea. VFA porewater concentrations were measured by a new two-dimensional ion chromatography-mass spectrometry method that enabled the direct analysis of VFAs without sample pretreatment. VFA concentrations were low and surprisingly constant (4–6 μmol L−1 for formate and acetate, and 0.5 μmol L−1 for propionate) throughout the sulfate reduction zone. Hence, VFAs are turned over while maintaining a stable concentration that is suggested to be under a strong microbial control. Estimated mean diffusion times of acetate between neighboring cells were <1 s, whereas VFA turnover times increased from several hours at the sediment surface to several years at the bottom of the sulfate reduction zone. Thus, diffusion was not limiting the VFA turnover. Despite constant VFA concentrations, the Gibbs energies (ΔGr) of VFA-dependent sulfate reduction decreased downcore, from −28 to −16 kJ (mol formate)−1, −68 to −31 kJ (mol acetate)−1, and −124 to −65 kJ (mol propionate)−1. Thus, ΔGr is apparently not determining the in-situ VFA concentrations directly. However, at the bottom of the sulfate zone of the shelf station, acetoclastic sulfate reduction might operate at its energetic limit at ~ −30 kJ (mol acetate)−1. It is not clear what controls VFA concentrations in the porewater but cell physiological constraints such as energetic costs of VFA activation or uptake could be important. We suggest that such constraints control the substrate turnover and result in a minimum ΔGr that depends on cell physiology and is different for individual substrates. PMID:26379631

Vertebral Fracture Assessment by dual-energy X-ray absorptiometry: insurance coverage issues in the United States. A White Paper of the International Society for Clinical Densitometry.

PubMed

Laster, Andrew J; Lewiecki, E Michael

2007-01-01

Clinical trial data and fracture risk prediction models unequivocally demonstrate the utility of identifying prevalent vertebral fractures to predict future fractures of all types. Knowledge of prevalent vertebral fractures can alter patient management decisions and result in initiation of therapy to reduce fracture risk in some patients who would not otherwise be treated. Cost-benefit analysis demonstrates that identifying and treating patients with vertebral fractures, even those with a densitometric classification of osteopenia, is cost effective. Vertebral fractures can be readily identified in the office setting using standard radiography or Vertebral Fracture Assessment (VFA), a software addition to a central dual-energy X-ray absorptiometry (DXA) machine. In the United States, VFA was assigned a Current Procedural Terminology (CPT) code in January 2005. Nevertheless, coverage of VFA has not been uniformly embraced by Medicare carriers, companies that contract with the federal government to administer Medicare coverage and process claims for a region of the United States. Unlike DXA, for which uniform national coverage of qualified Medicare beneficiaries is mandated by the Balanced Budget Act of 1997, VFA coverage policies are determined by the local Medicare carriers. Third-party insurers are also variable in their coverage of VFA. This International Society for Clinical Densitometry (ISCD) White Paper documents the role of VFA in the evaluation and treatment of women with postmenopausal osteoporosis and compares it with standard spine radiography. Arguments used by some Medicare carriers and insurers to deny coverage of VFA in the United States are analyzed and critiqued. For health care providers within the United States, this White Paper may serve as a resource to respond to insurers who deny coverage of VFA. For health care providers regardless of their country, this article underscores the value of VFA as an alternative to spine radiography in the evaluation and management of postmenopausal women with suspected osteoporosis.

The Associations Between Smoking Habits and Serum Triglyceride or Hemoglobin A1c Levels Differ According to Visceral Fat Accumulation

PubMed Central

Koda, Michiko; Kitamura, Itsuko; Okura, Tomohiro; Otsuka, Rei; Ando, Fujiko; Shimokata, Hiroshi

2016-01-01

Background Whether smokers and former smokers have worse lipid profiles or glucose levels than non-smokers remains unclear. Methods The subjects were 1152 Japanese males aged 42 to 81 years. The subjects were divided according to their smoking habits (nonsmokers, former smokers, and current smokers) and their visceral fat area (VFA) (<100 cm2 and ≥100 cm2). Results The serum triglyceride (TG) levels of 835 males were assessed. In the VFA ≥100 cm2 group, a significantly greater proportion of current smokers (47.3%) exhibited TG levels of ≥150 mg/dL compared with former smokers (36.4%) and non-smokers (18.8%). The difference in TG level distribution between former smokers and non-smokers was also significant. However, among the subjects with VFA of <100 cm2, the TG levels of the three smoking habit groups did not differ. The serum hemoglobin A1c (HbA1c) levels of 877 males were also assessed. In the VFA <100 cm2 group, significantly higher proportions of current smokers (17.9%) and former smokers (14.9%) demonstrated HbA1c levels of ≥5.6% compared with non-smokers (6.3%). In contrast, in the VFA ≥100 cm2 group, significantly fewer former smokers displayed HbA1c levels of ≥5.6% compared with non-smokers and current smokers. Furthermore, the interaction between smoking habits and VFA was associated with the subjects’ TG and HbA1c concentrations, and the associations of TG and HbA1c concentrations and smoking habits varied according to VFA. Conclusions Both smoking habits and VFA exhibited associations with TG and HbA1c concentrations. The associations between smoking habits and these parameters differed according to VFA. PMID:26616395

The inhibitory effect of bovine rumen fluid on Salmonella typhimurium.

PubMed

Chambers, P G; Lysons, R J

1979-05-01

The possible fate of Salmonella typhimurium in the rumen was investigated by monitoring rumen volatile fatty acids (VFA), lactate concentrations and pH over periods which included regular feeding and 48 h starvation. Preparations were made containing 50 per cent rumen fluid from the cow or VFA solutions, and then inoculated with S typhimurium. Viable counts before and after incubation for 24 h at 37 degrees C were compared. Incubation in broths with high concentrations of VFA and low pH resulted in a marked decrease in salmonella numbers, while lower VFA concentrations had little or no inhibitory effect on growth.

Visceral fat area is associated with HbA1c but not dialysate-related glucose load in nondiabetic PD patients

NASA Astrophysics Data System (ADS)

Ho, Li-Chun; Yen, Chung-Jen; Chao, Chia-Ter; Chiang, Chih-Kang; Huang, Jenq-Wen; Hung, Kuan-Yu

2015-08-01

Factors associated with increased visceral fat area (VFA) have been well documented in the general population but rarely explored in nondiabetic individuals on peritoneal dialysis (PD). As glycosylated hemoglobin (HbA1c) is positively correlated with VFA in diabetic patients, we hypothesized that the same correlation would exist in nondiabetic PD patients. We enrolled 105 nondiabetic patients who had undergone chronic PD for more than 3 months. Each subject underwent an abdominal computed tomography (CT) scan, and the umbilicus cut was analyzed for VFA. VFA values, corrected for body mass index and subjected to natural logarithm transformations, were examined to determine whether they were correlated with HbA1c and other parameters. PD dialysates prescribed at the time of enrollment were recorded to calculate glucose load. We found that when 105 nondiabetic PD patients were classified according to tertiles of HbA1c, higher HbA1c was associated with larger VFA. Multiple linear regression analysis revealed that HbA1c was an independent determinant of VFA, while glucose load and other PD-specific factors were not. In summary, HbA1c, but not PD-related glucose load, was positively correlated with VFA in nondiabetic PD patients, suggesting clinical utility of HbA1c in the PD population.

Enhanced biological phosphorus removal in a sequencing batch reactor using propionate as the sole carbon source.

PubMed

Pijuan, M; Saunders, A M; Guisasola, A; Baeza, J A; Casas, C; Blackall, L L

2004-01-05

An enhanced biological phosphorus removal (EBPR) system was developed in a sequencing batch reactor (SBR) using propionate as the sole carbon source. The microbial community was followed using fluorescence in situ hybridization (FISH) techniques and Candidatus 'Accumulibacter phosphatis' were quantified from the start up of the reactor until steady state. A series of SBR cycle studies was performed when 55% of the SBR biomass was Accumulibacter, a confirmed polyphosphate accumulating organism (PAO) and when Candidatus 'Competibacter phosphatis', a confirmed glycogen-accumulating organism (GAO), was essentially undetectable. These experiments evaluated two different carbon sources (propionate and acetate), and in every case, two different P-release rates were detected. The highest rate took place while there was volatile fatty acid (VFA) in the mixed liquor, and after the VFA was depleted a second P-release rate was observed. This second rate was very similar to the one detected in experiments performed without added VFA.A kinetic and stoichiometric model developed as a modification of Activated Sludge Model 2 (ASM2) including glycogen economy, was fitted to the experimental profiles. The validation and calibration of this model was carried out with the cycle study experiments performed using both VFAs. The effect of pH from 6.5 to 8.0 on anaerobic P-release and VFA-uptake and aerobic P-uptake was also studied using propionate. The optimal overall working pH was around 7.5. This is the first study of the microbial community involved in EBPR developed with propionate as a sole carbon source along with detailed process performance investigations of the propionate-utilizing PAOs. Copyright 2003 Wiley Periodicals, Inc.

The impact of reliable prebolus T 1 measurements or a fixed T 1 value in the assessment of glioma patients with dynamic contrast enhancing MRI.

PubMed

Tietze, Anna; Mouridsen, Kim; Mikkelsen, Irene Klærke

2015-06-01

Accurate quantification of hemodynamic parameters using dynamic contrast enhanced (DCE) MRI requires a measurement of tissue T 1 prior to contrast injection (T 1). We evaluate (i) T 1 estimation using the variable flip angle (VFA) and the saturation recovery (SR) techniques and (ii) investigate if accurate estimation of DCE parameters outperform a time-saving approach with a predefined T 1 value when differentiating high- from low-grade gliomas. The accuracy and precision of T 1 measurements, acquired by VFA and SR, were investigated by computer simulations and in glioma patients using an equivalence test (p > 0.05 showing significant difference). The permeability measure, K trans, cerebral blood flow (CBF), and - volume, V p, were calculated in 42 glioma patients, using fixed T 1 of 1500 ms or an individual T 1 measurement, using SR. The areas under the receiver operating characteristic curves (AUCs) were used as measures for accuracy to differentiate tumor grade. The T 1 values obtained by VFA showed larger variation compared to those obtained using SR both in the digital phantom and the human data (p > 0.05). Although a fixed T 1 introduced a bias into the DCE calculation, this had only minor impact on the accuracy differentiating high-grade from low-grade gliomas, (AUCfix = 0.906 and AUCind = 0.884 for K trans; AUCfix = 0.863 and AUCind = 0.856 for V p; p for AUC comparison > 0.05). T 1 measurements by VFA were less precise, and the SR method is preferable, when accurate parameter estimation is required. Semiquantitative DCE values, based on predefined T 1 values, were sufficient to perform tumor grading in our study.

Oriented acidification of wasted activated sludge (WAS) focused on odd-carbon volatile fatty acid (VFA): Regulation strategy and microbial community dynamics.

PubMed

Huang, Long; Chen, Zhiqiang; Xiong, Dandan; Wen, Qinxue; Ji, Ye

2018-06-01

As the main intermediate metabolite in anaerobic digestion of wasted activated sludge (WAS), volatile fatty acids (VFAs) are proper substrate for mixed culture (MC) polyhydroxyalkanoate (PHA) synthesis. To further optimize the performance of MC PHA production process, VFA _odd (i.e., VFA with odd carbon atoms) oriented acidification process was proposed and conducted in this study. Three regulation factors including reaction pH, fraction of added β-cyclodextrin (β-CD) and glycerol were selected and response surface methodology (RSM) was used to enhance and effectively regulate the VFA _odd production while maintaining enough acidification degree in the WAS acidification. High percentage of VFA _odd (larger than 60% and dominated by propionic acid) can be obtained in the operating condition area with glycerol addition ratio (quantified by C/N) ranging from 15 to 20 and reaction pH ranging from 8.0 to 9.5 when β-CD addition was held at zero level (0.2 g/gTSS) according to the RSM. Semi-continuous acidification and MC PHA production assays further verified the reliability and effectiveness of the VFA _odd oriented acidification strategy. Microbial function group related to propionic acid production (G prop ) was defined based on the relationships between system function and microbial community structure, and 13 frequent species were found being involved in the G prop . Roles of the group members in the oriented acidification were analyzed to understand the mechanisms of the regulation of VFA _odd production at microbial ecological level. A synergistic effect of WAS and glycerol on the VFA _odd production in the acidification process was revealed based on the ecological analysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

Vascular and metabolic effects of ezetimibe combined with simvastatin in patients with hypercholesterolemia.

PubMed

Koh, Kwang Kon; Oh, Pyung Chun; Sakuma, Ichiro; Kim, Eun Young; Lee, Yonghee; Hayashi, Toshio; Han, Seung Hwan; Park, Yae Min; Shin, Eak Kyun

2015-11-15

Ezetimibe demonstrates decreasing visceral fat and improving insulin sensitivity (IS) in animals and humans. We first reported that simvastatin dose-dependently worsens insulin sensitivity. Whether ezetimibe may compensate untoward effects of simvastatin, depending on dosages of simvastatin has not been investigated in patients with hypercholesterolemia, compared with simvastatin alone. This was a randomized, single-blind, placebo-controlled, parallel study. Fifty-one in each group were given placebo, ezetimibe 10mg combined with simvastatin 10mg (Vyto10), ezetimibe 10mg combined with simvastatin 20mg (Vyto20), or simvastatin 20mg alone (Simva20) daily for 2months. Placebo, Vyto10, Vyto20, and Simva20 improved flow-mediated dilation relative to baseline measurements. Placebo therapy did not significantly change insulin and IS and adiponectin levels and visceral fat area (VFA) and VFA/subcutaneous fat area (SFA) relative to baseline measurements. Vyto10 therapy significantly decreased CRP and insulin levels and increased adiponectin levels and IS, and reduced VFA, VFA/SFA, and blood pressure. Vyto20 therapy did not significantly change insulin levels and IS and adiponectin levels but significantly reduced CRP levels and VFA, VFA/SFA, and blood pressure. Simva20 therapy significantly decreased adiponectin levels and IS but did not significantly change VFA, VFA/SFA, and blood pressure. Of note, these different effects of each therapy were significant by ANOVA. Vyto10, Vyto20, and Simva20 showed significant reduction of LDL cholesterol levels and improvement of flow-mediated dilation in patients with hypercholesterolemia. However, Vyto10, Vyto20, and Simva20 showed significantly differential metabolic effects, depending on dosages of simvastatin. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Bicarbonate secretion and solute absorption in forestomach of the llama.

PubMed

Rübsamen, K; Engelhardt, W V

1978-07-01

Bicarbonate appearance in the lumen and its relationship to solute absorption were studied in a Pavlov pouch in the cardiac region of the first compartment of the llama forestomach. HCO3- appearance showed no diurnal variation. HCO3- accumulation was highly dependent on the pH of the solution used. The HCO3- ion probably is formed from CO2 diffusing into the lumen from the serosal side, as a result of cell metabolism and of OH- ions. HCO3- accumulation was closely related to volatile fatty acid (VFA) absorption. The ratio of HCO3- appearance to VFA absorption depended on the pH of the solution. At a pH of 6.6, about 0.1 mol HCO3- and, at a pH of 7.8, 0.9 mol HCO3- appeared per mole absorbed VFA, indicating that at slightly alkaline pH nearly all H+ ions required for the nonionic absorption of VFA appeared to be delivered from the dissociation of H2CO3. Bicarbonate gain and VFA absorption were increased when animals were not fed for 48 h. Sodium absorption was related to VFA as well as water absorption.

pH-adjustment strategy for volatile fatty acid production from high-strength wastewater for biological nutrient removal.

PubMed

Xie, Li; Liu, Hui; Chen, Yin-Guang; Zhou, Qi

2014-01-01

Volatile fatty acid (VFA) production from three types of high-strength organic wastewater (cassava thin stillage, starch wastewater and yellow-wine processing wastewater) were compared. The results showed that cassava thin stillage was the most suitable substrate, based on its high specific VFA production (0.68 g chemical oxygen demand (COD)/g initial soluble chemical oxygen demand (SCOD)) and yield (0.72 g COD/g SCOD) as well as low nutrient content in the substrate and fermented liquid. The acid fermented cassava thin stillage was evaluated and compared with sodium acetate in a sequencing batch reactor system. Total nitrogen removal efficiency was higher with fermented cassava thin stillage than with the sodium acetate. The effects of pH and a pH-adjustment strategy on VFA production and composition were determined using cassava thin stillage. At an initial pH range of 7-11, a relatively high VFA concentration of about 9 g COD/L was obtained. The specific VFA production (g COD/g initial SCOD) increased from 0.27 to 0.47 to 0.67 at pH 8 and from 0.26 to 0.68 to 0.81 at pH 9 (initial pH, interval pH, and constant pH adjustment, respectively). The dominant VFA species changed significantly with the increasing frequency of the pH adjustment. Further studies will examine the metabolic pathways responsible for VFA composition.

Microbial fuel cells operating on mixed fatty acids.

PubMed

Freguia, Stefano; Teh, Ee Hoi; Boon, Nico; Leung, Kar Man; Keller, Jurg; Rabaey, Korneel

2010-02-01

Strategies are being developed to harvest the energy content of the wasted sludge generated from the treatment of domestic wastewater. Sludge can be hydrolysed and fermented, giving a mixture of volatile fatty acids (VFAs). Based on the composition of such a fermented stream, synthetic media were created and tested for VFA conversion in microbial fuel cells (MFCs). Mainly acetate and propionate were preferred as electron donors in the mixed VFA system, which generated a power density of 49+/-1 mW L(NAC)(-1). The other VFAs (butyrates/valerates/caproic acid) were also removed, albeit at lower rates. In single VFA tests, each VFA could be removed, but particularly i-butyrate did not provide significant current generation. PCR-DGGE indicated that the microbial community structure was highly determined by the fed VFA, rather than by the initial inoculum. The communities were dominated by Proteobacteria such as Geobacter, Comamonas, Pseudomonas and Pelobacter species. This study demonstrated the feasibility of using fatty acids, as present in fermented sludge hydrolysates, for current generation.

Surfactant-enhanced anaerobic acidogenesis of Canna indica L. by rumen cultures.

PubMed

Yue, Zheng-Bo; Yu, Han-Qing; Hu, Zhen-Hu; Harada, Hideki; Li, Yu-You

2008-06-01

Polyoxyethylene sorbitan monoolate (Tween 80) was used to enhance the anaerobic acidogenesis of Canna indica L. (canna) by rumen culture in this study. Dose of Tween 80 at 1 ml/l enhanced the volatile fatty acids (VFA) production from the acidogenesis of canna compared to the control. However, Tween 80 at higher dosages than 5 ml/l inhibited the rumen microbial activity and reduced the VFA yield. Response surface methodology was successfully used to optimize the VFA yield. A maximum of VFA yield of 0.147 g/g total solids (TS) added was obtained at canna and Tween 80 concentrations of 6.3g TS/l and 2.0 ml/l, respectively. Dosage of Tween 80 at 1-3.75 ml/l reduced the unproductive adsorption of microbes or enzymes on the lignin part in canna and increased microbial activity. A high VFA production was achieved from canna presoaked with Tween 80, suggesting that the structure of canna was disrupted by Tween 80.

End product yields from the extraruminal fermentation of various polysaccharide, protein and nucleic acid components of biofuels feedstocks.

PubMed

Weimer, Paul J

2011-02-01

"Extraruminal" fermentations employing in vitro incubation of mixed ruminal bacterial consortia, are capable of converting a complex array of biomass materials to mixtures of volatile fatty acids (VFA), methane, and carbon dioxide. Most of the potential energy in the biomass feedstock is retained in the VFA products, which are potential reactants for electrochemical conversion to hydrocarbon fuels. Quantitative data on VFA yields and proportions from biomass components are necessary for determining industrial feasibility, but such measurements have not been systematically reported. VFA yields and proportions were determined for a variety of carbohydrates, proteins and nucleic acids. Carbohydrates yielded primarily acetic and propionic acids, while proteins also yielded a more favorable product mix (longer average chain length and branched chain VFAs). Addition of certain co-substrates (e.g., glycerol) favorably improved the VFA product mix. The results have implications for hydrocarbon fuel generation from biomass materials by hybrid fermentation/chemical processes. Published by Elsevier Ltd.

A modified two-point titration method for the determination of volatile fatty acids in anaerobic systems.

PubMed

Mu, Zhe-Xuan; He, Chuan-Shu; Jiang, Jian-Kai; Zhang, Jie; Yang, Hou-Yun; Mu, Yang

2018-08-01

The volatile fatty acids (VFA) concentration plays important roles in the rapid start-up and stable operation of anaerobic reactors. It's essential to develop a simple and accurate method to monitor the VFA concentration in the anaerobic systems. In present work, a modified two-point titration method was developed to determine the VFA concentration. The results show that VFA concentration in standard solutions estimated by the titration method coincided well with that measured by gas chromatograph, where all relative errors were lower than 5.5%. Compared with the phosphate, ammonium and sulfide subsystems, the effect of bicarbonate on the accuracy of the developed method was relatively significant. When the bicarbonate concentration varied from 0 to 8 mmol/L, the relative errors increased from 1.2% to 30% for VFA concentration at 1 mmol/L, but were within 2.0% for that at 5 mmol/L. In addition, the VFA composition affected the accuracy of the titration method to some extent. This developed titration method was further proved to be effective with practical effluents from a lab-scale anaerobic reactor under organic shock loadings and an unstable full-scale anaerobic reactor. Copyright © 2018 Elsevier Ltd. All rights reserved.

Build-up and impact of volatile fatty acids on E. coli and A. lumbricoides during co-digestion of urine diverting dehydrating toilet (UDDT-F) faeces.

PubMed

Riungu, Joy; Ronteltap, Mariska; van Lier, Jules B

2018-06-01

This study examined the potential of Escherichia coli (E. coli) and Ascaris lumbricoides (A. lumbricoides) eggs inactivation in faecal matter coming from urine diverting dehydrating toilets (UDDT-F) by applying high concentrations of volatile fatty acids (VFAs) during anaerobic stabilization. The impact of individual VFAs on E. coli and A. lumbricoides eggs inactivation in UDDT-F was assessed by applying various concentrations of store-bought acetate, propionate and butyrate. High VFA concentrations were also obtained by performing co-digestion of UDDT-F with organic market waste (OMW) using various mixing ratios. All experiments were performed under anaerobic conditions in laboratory scale batch assays at 35±1 °C. A correlation was observed between E. coli log inactivation and VFA concentration. Store bought VFA spiked UDDT-F substrates achieved E. coli inactivation up to 4.7 log units/day compared to UDDT-F control sample that achieved 0.6 log units/day. In co-digesting UDDT-F and organic market waste (OMW), a ND-VFA concentration of 4800-6000 mg/L was needed to achieve E. coli log inactivation to below detectable levels and complete A. lumbricoides egg inactivation in less than four days. E. coli and A. lumbricoides egg inactivation was found to be related to the concentration of non-dissociated VFA (ND-VFA), increasing with an increase in the OMW fraction in the feed substrate. Highest ND-VFA concentration of 6500 mg/L was obtained at a UDDT-F:OMW ratio 1:1, below which there was a decline, attributed to product inhibition of acidogenic bacteria. Results of our present research showed the potential for E. coli and A. lumbricoides inactivation from UDDT-F up to WHO standards by allowing VFA build-up during anaerobic stabilization of faecal matter. Copyright © 2018. Published by Elsevier Ltd.

In vitro fermentation characteristics of two mushroom species, an herb, and their polysaccharide fractions, using chicken cecal contents as inoculum.

PubMed

Guo, F C; Williams, B A; Kwakkel, R P; Verstegen, M W A

2003-10-01

In vitro fermentabilities of two mushrooms (Lentinus edodes--LenS; Tremella fuciformis--TreS), an herb (Astragalus membranaceus--AstS), and their polysaccharide fractions (LenE, TreE, and AstE) were investigated using microflora from chicken ceca. Polysaccharides were extracted using the hot water method. The mushrooms had lower polysaccharide yields (8 to 10%) than the herb (31%). Fermentation kinetics were determined using the in vitro cumulative gas production technique. End-products, such as gas, volatile fatty acids (VFA), and ammonia, were also determined. The gas profiles of intact materials were similar for AstS and LenS. The TreS had a diphasic digestion pattern. The extracts had similar profiles to the intact materials though gas production rates were faster. Intact materials tended to produce less VFA than the extracts though LenS and AstE had the highest total VFA production overall. Intact materials contained more protein than the extracts, and therefore resulted in more branched-chain fatty acids and ammonia. Fermentation kinetics and end-point products demonstrated differences in availability of substrates between the mushrooms and herb. These medicinal mushroom and herb materials, particularly their polysaccharide extracts, show promise in altering microbial activities and composition in chicken ceca. In vivo experiments are necessary for confirmation of this hypothesis.

A critical appraisal of vertebral fracture assessment in paediatrics.

PubMed

Kyriakou, Andreas; Shepherd, Sheila; Mason, Avril; Faisal Ahmed, S

2015-12-01

There is a need to improve our understanding of the clinical utility of vertebral fracture assessment (VFA) in paediatrics and this requires a thorough evaluation of its readability, reproducibility, and accuracy for identifying VF. VFA was performed independently by two observers, in 165 children and adolescents with a median age of 13.4 years (range, 3.6, 18). In 20 of these subjects, VFA was compared to lateral vertebral morphometry assessment on lateral spine X-ray (LVM). 1528 (84%) of the vertebrae were adequately visualised by both observers for VFA. Interobserver agreement in vertebral readability was 94% (kappa, 0.73 [95% CI, 0.68, 0.73]). 93% of the non-readable vertebrae were located between T6 and T9. Interobserver agreement per-vertebra for the presence of VF was 99% (kappa, 0.85 [95% CI, 0.79, 0.91]). Interobserver agreement per-subject was 91% (kappa, 0.78 [95% CI, 0.66, 0.87]). Per-vertebra agreement between LVM and VFA was 95% (kappa 0.79 [95% CI, 0.62, 0.92]) and per-subject agreement was 95% (kappa, 0.88 [95% CI, 0.58, 1.0]). Accepting LVM as the gold standard, VFA had a positive predictive value (PPV) of 90% and a negative predictive value (NPV) of 95% in per-vertebra analysis and a PPV of 100% and NPV of 93% in per-subject analysis. VFA reaches an excellent level of agreement between observers and a high level of accuracy in identifying VF in a paediatric population. The readability of vertebrae at the mid thoracic region is suboptimal and interpretation at this level should be exercised with caution. Copyright © 2015 Elsevier Inc. All rights reserved.

Elutriated acid fermentation of municipal primary sludge.

PubMed

Ahn, Young Ho; Speece, Richard E

2006-06-01

The performance of a novel fermentation process, adopting a sludge blanket type configuration, for higher hydrolysis/acidogenesis of the municipal primary sludge was investigated under batch and semi-continuous conditions with varying pH and temperature. This acid elutriation slurry reactor provided higher system performance with a short HRT (5d) and higher acidogenic effluent quality under pH 9 and thermophilic (55 degrees C) conditions. The hydrolysis of the sludge was revealed to be significantly dependent on seasonal effects for sludge characteristics but with little impact on acidogenesis. Based on the rainy season at the optimal conditions, VFA production and recovery fraction (VFA(COD)/COD) were 0.18 g VFA(COD)/g VSS(COD) and 63%. As byproducts, nitrogen and phosphorus release were measured at 0.006 g N/g VSS(COD) and 0.003 g P/g VSS(COD), respectively. For the mass balance in a full-scale plant (Q=158,880 m(3)/d) based on the rainy season, the VFA and non-VFA (as COD) production were 3110 kg VFA(COD)/d and 1800 kg COD/d, resulting in an increase of organics of 31 mg COD/L and 20mg VFA(COD)/L and nutrients of 0.7 mg N/L and 0.3 mg P/L in the influent sewage. The economical benefit from this process application was estimated to be about 67 dollars per 1000 m(3) of sewage except for energy requirements and also, better benefits can be expected during the dry season. Moreover, the results revealed that the process has various additional advantages such as pathogen-free stabilized solids production, excellent solids control and economical benefits.

Production of volatile fatty acids from sewage organic matter by combined bioflocculation and alkaline fermentation.

PubMed

Khiewwijit, Rungnapha; Temmink, Hardy; Labanda, Alvaro; Rijnaarts, Huub; Keesman, Karel J

2015-12-01

This study explored the potential of volatile fatty acids (VFA) production from sewage by a combined high-loaded membrane bioreactor and sequencing batch fermenter. VFA production was optimized with respect to SRT and alkaline pH (pH 8-10). Application of pH shock to a value of 9 at the start of a sequencing batch cycle, followed by a pH uncontrolled phase for 7days, gave the highest VFA yield of 440mgVFA-COD/g VSS. This yield was much higher than at fermentation without pH control or at a constant pH between 8 and 10. The high yield in the pH 9 shocked system could be explained by (1) a reduction of methanogenic activity, or (2) a high degree of solids degradation or (3) an enhanced protein hydrolysis and fermentation. VFA production can be further optimized by fine-tuning pH level and longer operation, possibly allowing enrichment of alkalophilic and alkali-tolerant fermenting microorganisms. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fermentation of wet-exploded corn stover for the production of volatile fatty acids.

PubMed

Murali, Nanditha; Fernandez, Sebastian; Ahring, Birgitte Kiaer

2017-03-01

Volatile fatty acids (VFA) have been used as platform molecules for production of biofuels and bioproducts. In the current study, we examine the VFA production from wet-exploded corn stover through anaerobic fermentation using rumen bacteria. The total VFA yield (acetic acid equivalents) was found to increase from 22.8g/L at 2.5% total solids (TS) to 40.8g/L at 5% TS. It was found that the acetic acid concentration increased from 10g/L to 22g/L at 2.5% and 5% TS, respectively. An increased propionic acid production was seen between day 10 and 20 at 5% TS. Valeric acid (4g/L) was produced at 5% TS and not at 2.5% TS. Composition analysis showed that 50% of the carbohydrates were converted to VFA at 5% TS and 33% at 2.5% TS. Our results show that rumen fermentation of lignocellulosic biomass after wet explosion can produce high concentrations of VFA without addition of external enzymes of importance for the process economics of lignocellulosic biorefineries. Copyright © 2016 Elsevier Ltd. All rights reserved.

A meta-analysis of variability in continuous-culture ruminal fermentation and digestibility data.

PubMed

Hristov, A N; Lee, C; Hristova, R; Huhtanen, P; Firkins, J L

2012-09-01

A meta-analysis was conducted to compare ruminal fermentation and digestibility data and variability between continuous-culture (CC) experiments and in vivo data. One hundred eighty CC studies representing 1,074 individual treatments, published in refereed journals between 1980 and 2010 were used in this analysis. Studies were classified into 2 groups based on the type of CC used: CC systems specified as rumen simulation techniques (RUSITEC) and non-RUSITEC CC systems (non-RUSITEC). The latter was a diverse group of systems, all of which were termed CC by the investigators. The CC data were compared with a data set of in vivo trials with ruminally cannulated lactating dairy cows (data from a total of 366 individual cows). The reported neutral detergent fiber (NDF) concentration of the diets fed in the 3 data sets was, on average (dry matter basis), 44, 34, and 32%, respectively. The average total volatile fatty acid (VFA) concentration for the RUSITEC and non-RUSITEC data sets was 67 and 80% (respectively) of the total VFA concentration in vivo. The average concentration of acetate was also lower for the CC data sets compared with in vivo and that of propionate was considerably lower for RUSITEC compared with in vivo, but butyrate concentrations were similar between the CC and in vivo data sets. Variability in the VFA data was generally the highest (higher coefficients of variation and variance) for the non-RUSITEC data set, followed by RUSITEC, and was the lowest for in vivo. Digestibilities of NDF and particularly organic matter were lower in the CC data sets compared with in vivo; the average NDF digestibility was 34.2, 45.5, and 53.0% for RUSITEC, non-RUSITEC, and in vivo, respectively. Variability in nutrient digestibility data followed the pattern of variability of the VFA data: highest variability for the non-RUSITEC data set, followed by RUSITEC, and the lowest for in vivo. This analysis showed that CC systems are generally characterized by lower total VFA and acetate concentrations, extremely low counts or lack of ruminal protozoa, and lower organic matter and NDF digestibilities than in vivo. Overall, variability was much greater for CC than for in vivo experimental data. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Volatile fatty acid profile for grass hay or alfalfa hay fed to alpacas (Vicugna pacos).

PubMed

Oldham, C L; Robinson, T F; Hunter, Z R; Taylor, L; White, J; Johnston, N P

2014-10-01

The purpose of this study was to determine the diurnal composition and concentration of volatile fatty acids (VFA) and to determine VFA composition and concentration differences between stomach compartment 1 (C1) and caecum of alpacas fed grass and alfalfa hay. The study was divided into two experiments. In Experiment 1 (EXP 1), 10 male alpacas (3+ years old, 65 kg BW) were divided into two groups, housed in drylot pens, provided ad libitum water and fed alfalfa (AH) or grass hay (GH) for 30 days. The alpacas were slaughtered and the digestive tract collected, divided into sub-tract sections, weighed and digesta sampled for pH, dry matter (DM) and NDF. Volatile fatty acid composition and concentration were determined on C1 and caecal material. Four adult male (3+ years old, 60 kg BW), C1 fistulated alpacas were housed in metabolism crates and divided into two forage groups for Experiment 2 (EXP 2). Alpacas were fed the forages as in EXP 1. Diurnal C1 VFA samples were drawn at 1, 3, 6, 9, 12, 18 and 24 h post-feeding. There were no differences between forages for tract weight, C1 and caecum digesta DM or NDF. Differences were noted (p < 0.05) for pH between forages and sub-tract site. Volatile fatty acids concentrations were different (p < 0.05) for forage and site, and total VFA was higher for AH than GH (110.6 and 79.1 mm) and C1 than caecum (40.7 and 27.6 mm). Proportion of VFA was significant (p < 0.05) for forage and site, C1 acetate highest for GH (84.8 vs. 74.0 mm) and caecum acetate 83.7 and 76.2 mm for GH and AH respectively. These data demonstrate the level of VFA produced in C1 and the caecum of alpacas and the diurnal VFA patterns. Composition of VFA is similar to other ruminant species. Journal of Animal Physiology and Animal Nutrition © 2013 Blackwell Verlag GmbH.

Optimisation of Noosa BNR plant to improve performance and reduce operating costs.

PubMed

Thomas, M; Wright, P; Blackall, L; Urbain, V; Keller, J

2003-01-01

Noosa WWTP is publicly owned and privately operated by Australian Water Services. The process includes primary sedimentation, raw sludge fermentation, biological nutrient removal (BNR), sand filtration and ultraviolet (UV) disinfection. An innovative feature of the plant is the supplementary carbon dosing facility to avoid the use of metal salts (alum or ferric) for phosphorus removal. The average flow treated during 2000 was 9.0 ML/d. The annual 50 percentile effluent quality requirements for nutrients are total N < 5 mg/L and total P < 1 mg/L. The objectives of this project were to: determine the cause of variability in phosphorus removal; develop a strategy to control the variability in phosphorus removal; and minimise the operating cost of supplementary carbon dosing while achieving the effluent quality requirements. An investigation of chemical and microbiological parameters was implemented and it was concluded that there were several factors causing variability in phosphorus removal, rather than a single cause. The following four major causes were identified, and the control strategies that were adopted resulted in the plant achieving annual 50 percentile effluent total P = 0.37 mg/L and total N = 3.0 mg/L during 2001. First, phosphorus removal was limited by the available VFA supply due to consumption of VFA by other organisms competing with phosphate accumulating organisms (PAO), and due to diurnal variations in the sewage VFA and phosphate concentrations. Therefore, supplementary carbon dosing was essential to make allowance for competing reactions. Second, increasing the fermenter VFA yield via supplementary carbon dosing with molasses was found to be an effective and economic way of ensuring reliable phosphorus removal. Third, nitrate in the RAS resulted in consumption of VFA by denitrifying bacteria, particularly with process configurations where the RAS was recycled directly into the anaerobic zone. Incorporating a RAS denitrification zone into the process rectified this problem. Finally, glycogen accumulating organisms (GAO) were observed in BNR sludge samples, and consumption of VFA by GAO appeared to cause decreased phosphorus removal. Better phosphorus removal was obtained using VFA derived from the fermenter than dosing an equivalent amount of acetic acid. It was hypothesized that GAO have a competitive advantage to use acetate and PAO have a competitive advantage to use propionate, butyrate or some other soluble COD compound in the fermenter effluent. Contrary to popular belief, acetate may not be the optimum VFA for biological phosphorus removal. The competition between PAO and GAO for different VFA species under anaerobic conditions requires further investigation in order to control the growth of GAO and thereby improve reliability of biological phosphorus removal processes.

The effect of mixing on fermentation of primary solids, glycerol, and biodiesel waste.

PubMed

Ghasemi, Marzieh; Randall, Andrew A

2018-03-01

In this study, the effect of mixing on volatile fatty acid (VFA) production and composition was investigated through running five identical bench-scale reactors that were filled with primary solid and dosed with either pure glycerol or biodiesel waste. Experimental results revealed that there was an inverse correlation between the mixing intensity and the VFA production. The total VFA production in the un-mixed reactor was 9,787 ± 3,601 mg COD/L, whereas in the reactor mixed at 100 rpm this dropped to 3,927 ± 1,175 mg COD/L, while both types of reactor were dosed with pure glycerol at the beginning of each cycle to reach the initial concentration of 1,000 mg/L (1,217 mg COD/L). Propionic acid was the dominant VFA in all the reactors except the reactor mixed at 30 rpm. It is hypothesized that low mixing facilitated hydrogen transfer between obligate hydrogen producing acetogens (OHPA) and hydrogen consuming acidogens in these non-methanogenic reactors. Also, in a narrower range of mixing (0 or 7 rpm), the total VFA production in biodiesel waste-fed reactors was considerably higher than that of pure glycerol-fed reactors.

The effect of pH control and 'hydraulic flush' on hydrolysis and Volatile Fatty Acids (VFA) production and profile in anaerobic leach bed reactors digesting a high solids content substrate.

PubMed

Cysneiros, Denise; Banks, Charles J; Heaven, Sonia; Karatzas, Kimon-Andreas G

2012-11-01

The effect of hydraulic flush and pH control on hydrolysis, Volatile Fatty Acids (VFA) production and profile in anaerobic leach bed reactors was investigated for the first time. Six reactors were operated under different regimes for two consecutive batches of 28days each. Buffering at pH ∼6.5 improved hydrolysis (Volatile Solid (VS) degradation) and VFA production by ∼50%. Butyric and acetic acid were dominant when reactors were buffered, while only butyric acid was produced at low pH. Hydraulic flush enhanced VS degradation and VFA production by ∼15% and ∼32%, respectively. Most Probable Number (MPN) of cellulolytic microorganisms indicated a wash out when hydraulic flush was applied, but pH control helped to counteract this. The highest VS degradation (∼89%), VFA yield (0.84kgCODkg(-1)VS(added)) and theoretical methane potential (0.37m(3)CH(4)kg(-1)VS(added)) were obtained when pH control and hydraulic flush were applied, and therefore, these conditions are recommended. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of illite supplementation on in vitro and in vivo rumen fermentation, microbial population and methane emission of Hanwoo steers fed high concentrate diets.

PubMed

Biswas, Ashraf A; Lee, Sung-Sill; Mamuad, Lovelia L; Kim, Seon-Ho; Choi, Yeon-Jae; Lee, Chanhee; Lee, Kichoon; Bae, Gui-Seck; Lee, Sang-Suk

2018-01-01

This study was conducted to evaluate the effects of feeding supplemental illite to Hanwoo steers on methane (CH 4 ) emission and rumen fermentation parameters. An in vitro ruminal fermentation technique was conducted using a commercial concentrate as substrate and illite was added at different concentrations as treatments: 0%, 0.5%, 1.0%, and 2.0% illite. Total volatile fatty acids (VFA) were different (P < 0.05) at 24 h of incubation where the highest total VFA was observed at 1.0% of illite. Conversely, lowest CH 4 production (P < 0.01) was found at 1.0% of illite. In the in vivo experiment, two diets were provided, without illite and with addition of 1% illite. An automated head chamber (GreenFeed) system was used to measure enteric CH 4 production. Cattle received illite supplemented feed increased (P < 0.05) total VFA concentrations in the rumen compared with those fed control. Feeding illite numerically decreased CH 4 production (g/day) and yield (g/kg dry matter intake). Rumen microbial population analysis indicated that the population of total bacteria, protozoa and methanogens were lower (P < 0.05) for illite compared with the control. Accordingly, overall results suggested that feeding a diet supplemented with 1% illite can have positive effects on feed fermentation in the rumen and enteric CH 4 mitigation in beef cattle. © 2017 Japanese Society of Animal Science.

Effects of three methane mitigation agents on parameters of kinetics of total and hydrogen gas production, ruminal fermentation and hydrogen balance using in vitro technique.

PubMed

Wang, Min; Wang, Rong; Yang, Shan; Deng, Jin Ping; Tang, Shao Xun; Tan, Zhi Liang

2016-02-01

Methane (CH4 ) can be mitigated through directly inhibiting methanogen activity and starving methanogens by hydrogen (H2 ) sink. Three types of mechanism (i.e. bromoethanesulphonate (BES), nitrate and emodin) and doses of CH4 mitigation agents were employed to investigate their pathways of CH4 inhibition. Results indicated that both BES and emodin inhibited CH4 production and altered H2 balance, which could be accompanied by decreased dry matter disappearance (DMD), fractional rate of gH2 formation, volatile fatty acid (VFA) production, ability to produce and use reducing equivalences and molecular H2 , and increased final asymptotic gH2 production, time to the peak of gH2 , discrete lag time of gH2 production and fermentation efficiency. However, emodin decreased gas volume produced by rapidly fermentable components of substrate and the rate of fermentation at early stage of incubation, while BES supplementation inhibited gas volume produced by both rapidly and slowly fermentable components of substrate and the rate of fermentation at middle or late stage of incubation. The nitrate supplementation inhibited CH4 production without affecting VFA profile, because of its dual role as H2 sink and being toxic to methanogens. Nitrate supplementation had more complicated pattern of fermentation, VFA production and profile and H2 balance in comparison to BES and emodin supplementation. © 2015 Japanese Society of Animal Science.

Visceral fat area is a strong predictor of leukocyte cell-derived chemotaxin 2, a potential biomarker of dyslipidemia.

PubMed

Tanisawa, Kumpei; Taniguchi, Hirokazu; Sun, Xiaomin; Ito, Tomoko; Kawakami, Ryoko; Sakamoto, Shizuo; Higuchi, Mitsuru

2017-01-01

Leukocyte cell-derived chemotaxin 2 (LECT2) is a hepatokine linking obesity to skeletal muscle insulin resistance. Although previous studies reported that obesity was associated with high levels of circulating LECT2 in human, the associations of detailed body fat distribution with LECT2 levels have not been examined. Furthermore, although animal study suggested that exercise decreased circulating LECT2 levels, it remains unknown whether physical fitness is associated with LECT2 levels in human. We therefore examined the relationship of plasma LECT2 levels with various adiposity indices and cardiorespiratory fitness (CRF) in middle-aged and elderly Japanese men. Furthermore, we examined the relationship of LECT2 levels with the presence of metabolic syndrome, hypertension, insulin resistance and dyslipidemia to determine the clinical significance of measuring circulating LECT2. This was a cross-sectional study of 143 Japanese men (age: 30-79 years). Participants' plasma LECT2 levels were measured by an enzyme-linked immunosorbent assay. To assess their abdominal fat distributions, visceral fat area (VFA) and subcutaneous fat area (SFA) were measured using magnetic resonance imaging. CRF was assessed by measuring peak oxygen uptake ([Formula: see text]). All adiposity indices measured in this study were positively correlated with plasma LECT2 levels, while [Formula: see text] was negatively correlated with LECT2 levels after adjustment for age. The correlations, except for VFA were no longer significant with further adjustment for VFA. Stepwise multiple linear regression analysis revealed that VFA was the strongest predictor of plasma LECT2 levels. Plasma LECT2 levels differed based on the presence of metabolic syndrome and dyslipidemia, but not hypertension and insulin resistance. Logistic regression analyses revealed that plasma LECT2 levels were significantly associated with dyslipidemia independently of VFA; VFA was not significantly associated with dyslipidemia after adjustment for LECT2. VFA was the strongest predictor of plasma LECT2 that is a potential biomarker linking visceral obesity to dyslipidemia.

Cut-Off Values of Visceral Fat Area and Waist-to-Height Ratio: Diagnostic Criteria for Obesity-Related Disorders in Korean Children and Adolescents

PubMed Central

Lee, Kang-Kon; Park, Hye-Soon

2012-01-01

Purpose The aim of this study was to study the appropriate cut-off value of visceral fat area (VFA) and waist-to-height ratio (WTHR) which increase the risk of obesity-related disorders and to validate the diagnostic criteria of abdominal obesity and metabolic syndrome in Korean children and adolescents. Materials and Methods A total 314 subjects (131 boys and 183 girls) were included in this study. The subjects were selected from Korean children and adolescents who visited three University hospitals in Seoul and Uijeongbu from January 1999 to December 2009. All patients underwent computed tomography to measure VFA. Results The cut-off value of VFA associated with an increase risk of obesity-related disorder, according to the receiver operating characteristics curve, was 68.57 cm2 (sensitivity 59.8%, specificity 76.6%, p=0.01) for age between 10 to 15 years, and 71.10 cm2 (sensitivity 72.3%, specificity 76.5%, p<0.001) for age between 16 to 18 years. By simple regression analysis, the WTHR corresponding to a VFA of 68.57 cm2 was 0.54 for boys and 0.61 for girls, and the WTHR corresponding to a VFA of 71.10 cm2 was 0.51 for boys and 0.56 for girls (p=0.004 for boys, p<0.001 for girls). Conclusion Based on the results of this study, VFA which increases the risk of obesity-related disorders was 68.57 cm2 and the WTHR corresponding to this VFA was 0.54 for boys and 0.61 for girls age between 10-15 years, 71.70 cm2 and the WTHR 0.51 for boys and 0.56 for girls age between 16-18 years. For appropriate diagnostic criteria of abdominal obesity and obesity-related disorders in Korean children and adolescents, further studies are required. PMID:22187238

Associations of serum adipocyte fatty acid binding protein with body composition and fat distribution in nondiabetic Chinese women.

PubMed

Hao, Yaping; Ma, Xiaojing; Luo, Yuqi; Hu, Xiang; Pan, Xiaoping; Xiao, Yunfeng; Bao, Yuqian; Jia, Weiping

2015-05-01

Previous studies have demonstrated evidence of a positive relationship between serum adipocyte fatty acid binding protein (A-FABP) and obesity. However, associations of A-FABP with body composition and ectopic fat accumulation remain unclear. This study aimed to elucidate the effect of body composition, visceral fat area (VFA), and subcutaneous fat area (SFA) on serum A-FABP levels in a cohort of Chinese women without diabetes mellitus. A total of 2108 women without diabetes (760 premenopausal and 1348 postmenopausal women; age, 20-78 y) selected from the Shanghai Obesity Study were enrolled. VFA and SFA were measured by magnetic resonance imaging, and body composition was determined by bioelectrical impedance analysis. A high VFA was defined as ≥ 80 cm(2). A high SFA was defined as that above the 75th percentile cutoff point of the menopause-specific population, respectively. Serum A-FABP levels were higher in postmenopausal than premenopausal women (P < .001). Both premenopausal and postmenopausal women with an isolated high VFA had higher A-FABP levels than did those with an isolated high SFA (P = .017 and .002, respectively). In both body mass index (BMI) groups (< 25 and ≥ 25 kg/m(2)), women with a high VFA had higher serum A-FABP levels regardless of their menopausal status. Multiple stepwise regression analysis showed that A-FABP was independently associated with fat mass (Standardized β = 0.417 and 0.252 for premenopausal and postmenopausal status, respectively, both P < .001). Moreover, VFA was identified as an independent risk factor for A-FABP in postmenopausal women (Standardized β = 0.114, P = .001). Application of the same regression analyses model to the two BMI groups produced similar results in both BMI categories. Serum A-FABP levels were associated with fat mass, and were also influenced by VFA after menopause in Chinese women without diabetes mellitus.

A clustering-based graph Laplacian framework for value function approximation in reinforcement learning.

PubMed

Xu, Xin; Huang, Zhenhua; Graves, Daniel; Pedrycz, Witold

2014-12-01

In order to deal with the sequential decision problems with large or continuous state spaces, feature representation and function approximation have been a major research topic in reinforcement learning (RL). In this paper, a clustering-based graph Laplacian framework is presented for feature representation and value function approximation (VFA) in RL. By making use of clustering-based techniques, that is, K-means clustering or fuzzy C-means clustering, a graph Laplacian is constructed by subsampling in Markov decision processes (MDPs) with continuous state spaces. The basis functions for VFA can be automatically generated from spectral analysis of the graph Laplacian. The clustering-based graph Laplacian is integrated with a class of approximation policy iteration algorithms called representation policy iteration (RPI) for RL in MDPs with continuous state spaces. Simulation and experimental results show that, compared with previous RPI methods, the proposed approach needs fewer sample points to compute an efficient set of basis functions and the learning control performance can be improved for a variety of parameter settings.

Storage capacity of subcutaneous fat in Japanese adults.

PubMed

Sato, S; Demura, S; Nakai, M

2015-08-01

On the basis of our previous study, which examined the nonlinear relationship between visceral fat area (VFA) and percent regional fat mass in the trunk, we hypothesise the presence of some storage capacity of subcutaneous fat. This study aimed to examine the storage capacity of subcutaneous fat on the basis of subcutaneous fat area (SFA) and VFA in 791 Japanese adult males and 563 females. Regression analyses by using SFA as a dependent variable and VFA as an independent variable were performed for each group classified by visceral fat obesity (VO): VO (VFA ⩾ 100 cm(2)) and the no-VO (NVO) groups. To statistically identify an optimal critical point for subcutaneous fat accumulation, we changed the cutoff point for the VO group from 50-150 cm(2) in 10-cm(2) increments and confirmed the significance of the correlation between SFA and VFA for each obesity group, the statistical difference in correlations between NVO and VO groups, and the goodness of fit for the two regression lines using the standard error of estimation values. These analyses were conducted for each sex and age (<65 and ⩾ 65 years) group. The critical point for subcutaneous fat accumulation appears at the following cutoff points of VFA: 130 cm(2) in <65-year-old males, 110 cm(2) in ⩾ 65-year-old males and 100 cm(2) in both female groups. These results suggest the presence of some storage capacity of subcutaneous fat. As a further application, these findings may serve to improve the risk assessment of obesity-related diseases.

The relationship between visceral obesity and hepatic steatosis measured by controlled attenuation parameter

PubMed Central

Jung, Kyu Sik; Chon, Young Eun; Huh, Ji Hye; Park, Kyeong Hye; Chung, Jae Bock; Kim, Chang Oh; Han, Kwang-Hyub

2017-01-01

Background Nonalcoholic fatty liver disease (NAFLD) is closely related with obesity. However, obese subjects, generally represented by high BMI, do not always develop NAFLD. A number of possible causes of NAFLD have been studied, but the exact mechanism has not yet been elucidated. Methods A total of 304 consecutive subjects who underwent general health examinations including abdominal ultrasonography, transient elastography and abdominal fat computed tomography were prospectively enrolled. Significant steatosis was diagnosed by ultrasonography and controlled attenuation parameter (CAP) assessed by transient elastography. Results Visceral fat area (VFA) was significantly related to hepatic steatosis assessed by CAP, whereas body mass index (BMI) was related to CAP only in univariate analysis. In multiple logistic regression analysis, VFA (odds ratio [OR], 1.010; 95% confidence interval [CI], 1.001–1.019; P = 0.028) and triglycerides (TG) (OR, 1.006; 95% CI, 1.001–1.011; P = 0.022) were independent risk factors for significant hepatic steatosis. The risk of significant hepatic steatosis was higher in patients with higher VFA: the OR was 4.838 (P<0.001; 95% CI, 2.912–8.039) for 100200 cm2, compared to patients with a VFA ≤100 cm2. Conclusions Our data demonstrated that VFA and TG is significantly related to hepatic steatosis assessed by CAP not BMI. This finding suggests that surveillance for subjects with NAFLD should incorporate an indicator of visceral obesity, and not simply rely on BMI. PMID:29077769

Lactic-fermented egg white improves visceral fat obesity in Japanese subjects-double-blind, placebo-controlled study.

PubMed

Matsuoka, Ryosuke; Kamachi, Keiko; Usuda, Mika; Wang, Wei; Masuda, Yasunobu; Kunou, Masaaki; Tanaka, Akira; Utsunomiya, Kazunori

2017-12-08

It was reported that egg white protein (EWP) reduced body fat in rats. We developed a lactic-fermented egg white (LE) that facilitates the consumption of egg whites by fermenting them with lactobacillus, and were able to study their intake in humans. In this double-blind, placebo-controlled design, we evaluated the effect of LE on visceral fat area (VFA). Participants included 37 adult males and females aged ≥40 years (VFA at navel ≥100 cm 2 ). They were divided into two groups: the control group and the LE group. The control and LE groups consumed drinks containing whey and LE, respectively, for 12 weeks (providing 8 g protein/day). VFA was measured at baseline and at week 12 of intake. Abdominal girth was measured at baseline and at weeks 6 and 12. LE intake decreased VFA significantly compared with baseline (-8.89 cm 2 , p < 0.05), and VFA was significantly lower than that in the control group (+1.71 cm 2 , p < 0.05). The LE group showed significant improvement in the ratio of visceral to subcutaneous fat area compared with baseline and the control group (p < 0.05). The results demonstrated that LE reduces VFA and improves the ratio of visceral to subcutaneous fat area. As other measurement items were not influenced, we concluded that LE improves visceral fat obesity. This clinical trial was retrospectively registered with the University hospital Medical Information Network (UMIN) Center, ( UMIN000026949 ; registered on 11/04/2017; http://www.umin.ac.jp /).

Evaluation of MRI sequences for quantitative T1 brain mapping

NASA Astrophysics Data System (ADS)

Tsialios, P.; Thrippleton, M.; Glatz, A.; Pernet, C.

2017-11-01

T1 mapping constitutes a quantitative MRI technique finding significant application in brain imaging. It allows evaluation of contrast uptake, blood perfusion, volume, providing a more specific biomarker of disease progression compared to conventional T1-weighted images. While there are many techniques for T1-mapping there is a wide range of reported T1-values in tissues, raising the issue of protocols reproducibility and standardization. The gold standard for obtaining T1-maps is based on acquiring IR-SE sequence. Widely used alternative sequences are IR-SE-EPI, VFA (DESPOT), DESPOT-HIFI and MP2RAGE that speed up scanning and fitting procedures. A custom MRI phantom was used to assess the reproducibility and accuracy of the different methods. All scans were performed using a 3T Siemens Prisma scanner. The acquired data processed using two different codes. The main difference was observed for VFA (DESPOT) which grossly overestimated T1 relaxation time by 214 ms [126 270] compared to the IR-SE sequence. MP2RAGE and DESPOT-HIFI sequences gave slightly shorter time than IR-SE (~20 to 30ms) and can be considered as alternative and time-efficient methods for acquiring accurate T1 maps of the human brain, while IR-SE-EPI gave identical result, at a cost of a lower image quality.

Comparison of updates to the Molly cow model to predict methane production from dairy cows fed pasture.

PubMed

Gregorini, P; Beukes, P C; Hanigan, M D; Waghorn, G; Muetzel, S; McNamara, J P

2013-08-01

Molly is a deterministic, mechanistic, dynamic model representing the digestion, metabolism, and production of a dairy cow. This study compared the predictions of enteric methane production from the original version of Molly (MollyOrigin) and 2 new versions of Molly. Updated versions included new ruminal fiber digestive parameters and animal hormonal parameters (Molly84) and a revised version of digestive and ruminal parameters (Molly85), using 3 different ruminal volatile fatty acid (VFA) stoichiometry constructs to describe the VFA pattern and methane (CH4) production (g of CH4/d). The VFA stoichiometry constructs were the original forage and mixed-diet VFA constructs and a new VFA stoichiometry based on a more recent and larger set of data that includes lactate and valerate production, amylolytic and cellulolytic bacteria, as well as protozoal pools. The models' outputs were challenged using data from 16 dairy cattle 26 mo old [standard error of the mean (SEM)=1.7], 82 (SEM=8.7) d in milk, producing 17 (SEM=0.2) kg of milk/d, and fed fresh-cut ryegrass [dry matter intake=12.3 (SEM=0.3) kg of DM/d] in respiration chambers. Mean observed CH4 production was 266±5.6 SEM (g/d). Mean predicted values for CH4 production were 287 and 258 g/d for MollyOrigin without and with the new VFA construct. Model Molly84 predicted 295 and 288 g of CH4/d with and without the new VFA settings. Model Molly85 predicted the same CH4 production (276 g/d) with or without the new VFA construct. The incorporation of the new VFA construct did not consistently reduce the low prediction error across the versions of Molly evaluated in the present study. The improvements in the Molly versions from MollyOrigin to Molly84 to Molly85 resulted in a decrease in mean square prediction error from 8.6 to 8.3 to 4.3% using the forage diet setting. The majority of the mean square prediction error was apportioned to random bias (e.g., 43, 65, and 70% in MollyOrigin, Molly84, and Molly85, respectively, on the forage setting, showing that with the updated versions a greater proportion of error was random). The slope bias was less than 2% in all cases. We concluded that, of the versions of Molly used for pastoral systems, Molly85 has the capability to predict CH4 production from grass-fed dairy cows with the highest accuracy. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Clinical Evaluation of an Affordable Qualitative Viral Failure Assay for HIV Using Dried Blood Spots in Uganda.

PubMed

Balinda, Sheila N; Ondoa, Pascale; Obuku, Ekwaro A; Kliphuis, Aletta; Egau, Isaac; Bronze, Michelle; Kasambula, Lordwin; Schuurman, Rob; Spieker, Nicole; Rinke de Wit, Tobias F; Kityo, Cissy

2016-01-01

WHO recommends regular viral load (VL) monitoring of patients on antiretroviral therapy (ART) for timely detection of virological failure, prevention of acquired HIV drug resistance (HIVDR) and avoiding unnecessary switching to second-line ART. However, the cost and complexity of routine VL testing remains prohibitive in most resource limited settings (RLS). We evaluated a simple, low-cost, qualitative viral-failure assay (VFA) on dried blood spots (DBS) in three clinical settings in Uganda. We conducted a cross-sectional diagnostic accuracy study in three HIV/AIDS treatment centres at the Joint Clinical Research Centre in Uganda. The VFA employs semi-quantitative detection of HIV-1 RNA amplified from the LTR gene. We used paired dry blood spot (DBS) and plasma with the COBASAmpliPrep/COBASTaqMan, Roche version 2 (VLref) as the reference assay. We used the VFA at two thresholds of viral load, (>5,000 or >1,000 copies/ml). 496 paired VFA and VLref results were available for comparative analysis. Overall, VFA demonstrated 78.4% sensitivity, (95% CI: 69.7%-87.1%), 93% specificity (95% CI: 89.7%-96.4%), 89.3% accuracy (95% CI: 85%-92%) and an agreement kappa = 0.72 as compared to the VLref. The predictive values of positivity and negativity among patients on ART for >12 months were 72.7% and 99.3%, respectively. VFA allowed 89% of correct classification of VF. Only 11% of the patients were misclassified with the potential of unnecessary or late switch to second-line ART. Our findings present an opportunity to roll out simple and affordable VL monitoring for HIV-1 treatment in RLS.

Pretreatment of macroalgae for volatile fatty acid production.

PubMed

Pham, Thi Nhan; Um, Youngsoon; Yoon, Hyon Hee

2013-10-01

In this study, a novel method was proposed for the biological pretreatment of macroalgae (Laminaria japonica, Pachymeniopsis elliptica, and Enteromorpha crinita) for production of volatile fatty acid (VFA) by anaerobic fermentation. The amount of VFA produced from 40 g/L of L. japonica increased from 8.3 g/L (control) to 15.6 g/L when it was biologically pretreated with Vibrio harveyi. The biological treatment of L. japonica with Vibrio spp. was most effective likely due to the alginate lyase activity of Vibrio spp. However, a considerable effect was also observed after biological pretreatment of P. elliptica and E. crinita, which are red and green algae, respectively. Alkaline pretreatment of 40 g/L of L. japonica with 0.5 N NaOH resulted in an increase of VFA production to 12.2 g/L. These results indicate that VFA production from macroalgae can be significantly enhanced using the proposed biological pretreatments. Copyright © 2013 Elsevier Ltd. All rights reserved.

The one-stage autothermal thermophilic aerobic digestion for sewage sludge treatment: stabilization process and mechanism.

PubMed

Liu, Shugen; Zhu, Nanwen; Li, Loretta Y

2012-01-01

Batch experiment was carried out in a simulated thermophilic aerobic digester to investigate the digestion process of one-stage autothermal thermophilic aerobic digester and to explore the sludge stabilization mechanism. Volatile solids removal was 38.4% at 408 h and 45.0% at 552 h. Chemical oxidation demand, total nitrogen, and ammonia nitrogen in supernatant increased rapidly up to 168 h, and all of them fluctuated moderately after 360 h. Volatile fatty acid (VFA) accumulated rapidly up to 24 to 168 h, then declined sharply, reaching a low concentration after 312 h. Propionic, iso-valeric, and iso-butyric acids, in addition to acetic acids, were also the major components of VFA. As the biochemical metabolic process was inhibited under oxygen-deficiency condition, the digestion system can produce acetic, propionic, butyric acids and other VFA constituents to meet the demand for NAD(+) and maximize ATP generation. The ORP affected the VFA production and depletion as well as sulfate levels. Copyright © 2011 Elsevier Ltd. All rights reserved.

Early warning indicators for monitoring the process failure of anaerobic digestion system of food waste.

PubMed

Li, Lei; He, Qingming; Wei, Yunmei; He, Qin; Peng, Xuya

2014-11-01

To determine reliable state parameters which could be used as early warning indicators of process failure due to the acidification of anaerobic digestion of food waste, three mesophilic anaerobic digesters of food waste with different operation conditions were investigated. Such parameters as gas production, methane content, pH, concentrations of volatile fatty acid (VFA), alkalinity and their combined indicators were evaluated. Results revealed that operation conditions significantly affect the responses of parameters and thus the optimal early warning indicators of each reactor differ from each other. None of the single indicators was universally valid for all the systems. The universally valid indicators should combine several parameters to supply complementary information. A combination of total VFA, the ratio of VFA to total alkalinity (VFA/TA) and the ratio of bicarbonate alkalinity to total alkalinity (BA/TA) can reflect the metabolism of the digesting system and realize rapid and effective early warning. Copyright © 2014 Elsevier Ltd. All rights reserved.

Variable flip angle 3D ultrashort echo time (UTE) T1 mapping of mouse lung: A repeatability assessment.

PubMed

Alamidi, Daniel F; Smailagic, Amir; Bidar, Abdel W; Parker, Nicole S; Olsson, Marita; Hockings, Paul D; Lagerstrand, Kerstin M; Olsson, Lars E

2018-03-08

Lung T 1 is a potential translational biomarker of lung disease. The precision and repeatability of variable flip angle (VFA) T 1 mapping using modern 3D ultrashort echo time (UTE) imaging of the whole lung needs to be established before it can be used to assess response to disease and therapy. To evaluate the feasibility of regional lung T 1 quantification with VFA 3D-UTE and to investigate long- and short-term T 1 repeatability in the lungs of naive mice. Prospective preclinical animal study. Eight naive mice and phantoms. 3D free-breathing radial UTE (8 μs) at 4.7T. VFA 3D-UTE T 1 calculations were validated against T 1 values measured with inversion recovery (IR) in phantoms. Lung T 1 and proton density (S 0 ) measurements of whole lung and muscle were repeated five times over 1 month in free-breathing naive mice. Two consecutive T 1 measurements were performed during one of the imaging sessions. Agreement in T 1 between VFA 3D-UTE and IR in phantoms was assessed using Bland-Altman and Pearson 's correlation analysis. The T 1 repeatability in mice was evaluated using coefficient of variation (CV), repeated-measures analysis of variance (ANOVA), and paired t-test. Good T 1 agreement between the VFA 3D-UTE and IR methods was found in phantoms. T 1 in lung and muscle showed a 5% and 3% CV (1255 ± 63 msec and 1432 ± 42 msec, respectively, mean ± SD) with no changes in T 1 or S 0 over a month. Consecutive measurements resulted in an increase of 2% in both lung T 1 and S 0 . VFA 3D-UTE shows promise as a reliable T 1 mapping method that enables full lung coverage, high signal-to-noise ratio (∼25), and spatial resolution (300 μm) in freely breathing animals. The precision of the VFA 3D-UTE method will enable better design and powering of studies. 1 Technical Efficacy: Stage 2 J. Magn. Reson. Imaging 2018. © 2018 International Society for Magnetic Resonance in Medicine.

Evaluation of the 5 and 8 pH point titration methods for monitoring anaerobic digesters treating solid waste.

PubMed

Vannecke, T P W; Lampens, D R A; Ekama, G A; Volcke, E I P

2015-01-01

Simple titration methods certainly deserve consideration for on-site routine monitoring of volatile fatty acid (VFA) concentration and alkalinity during anaerobic digestion (AD), because of their simplicity, speed and cost-effectiveness. In this study, the 5 and 8 pH point titration methods for measuring the VFA concentration and carbonate system alkalinity (H2CO3*-alkalinity) were assessed and compared. For this purpose, synthetic solutions with known H2CO3*-alkalinity and VFA concentration as well as samples from anaerobic digesters treating three different kind of solid wastes were analysed. The results of these two related titration methods were verified with photometric and high-pressure liquid chromatography measurements. It was shown that photometric measurements lead to overestimations of the VFA concentration in the case of coloured samples. In contrast, the 5 pH point titration method provides an accurate estimation of the VFA concentration, clearly corresponding with the true value. Concerning the H2CO3*-alkalinity, the most accurate and precise estimations, showing very similar results for repeated measurements, were obtained using the 8 pH point titration. Overall, it was concluded that the 5 pH point titration method is the preferred method for the practical monitoring of AD of solid wastes due to its robustness, cost efficiency and user-friendliness.

The effects of intermittent use of the SGLT-2 inhibitor, dapagliflozin, in overweight patients with type 2 diabetes in Japan: a randomized, crossover, controlled clinical trial.

PubMed

Kato, Kanako; Suzuki, Kunihiro; Aoki, Chie; Sagara, Masaaki; Niitani, Takafumi; Wakamatsu, Sho; Yanagi, Kazunori; Aso, Yoshimasa

2017-06-01

This study examined the effects of short-term administration of the sodium glucose cotransporter 2 (SGLT-2) inhibitor, dapagliflozin, on visceral fat area (VFA) in Japanese patients with type 2 diabetes. In this randomized, crossover, controlled clinical trial, overweight patients with type 2 diabetes were randomized to treatment with 5 mg dapagliflozin for the first (n = 27) or second 12-week study period (n = 29). The parameters evaluated at baseline and after 12 and 24 weeks included blood pressure, hemoglobin A1c (HbA1c), body composition, VFA, and subcutaneous fat area (SFA). In both groups, dapagliflozin administration improved the levels of HbA1c, body weight, blood pressure, total fat mass, and VFA. Cessation of dapagliflozin, however, reversed the improvements in HbA1c, blood pressure, body weight, and SFA levels, whereas reductions in VFA and total fat mass levels were somewhat maintained even after 12 weeks without treatment. Dapagliflozin led to decreases in VFA and, consequently, body weight after a short treatment period. However, these effects were largely reversed by the cessation of dapagliflozin, suggesting that this agent should be administered continuously to maintain clinical usefulness in overweight patients with type 2 diabetes.

EPIGENETIC REGULATION IN BOVINE CELLS: NUTRIENT-INDUCED MODULATION OF GENE EXPRESSION AND CELLULAR FUNCTIONS

USDA-ARS?s Scientific Manuscript database

Research on epigenetics and nutrigenetics, the genome-nutrient interface is in its infancy with respect to livestock species. Ruminant species have evolved to metabolize short-chain fatty acids (VFA) to fulfill up to 70% of their energy requirements. Our studies revealed that VFA, especially butyr...

Sustainable multistage process for enhanced productivity of bioplastics from waste remediation through aerobic dynamic feeding strategy: Process integration for up-scaling.

PubMed

Amulya, K; Jukuri, Srinivas; Venkata Mohan, S

2015-01-01

Polyhydroxyalkanoates (PHA) production was evaluated in a multistage operation using food waste as a renewable feedstock. The first step involved the production of bio-hydrogen (bio-H2) via acidogenic fermentation. Volatile fatty acid (VFA) rich effluent from bio-H2 reactor was subsequently used for PHA production, which was carried out in two stages, Stage II (culture enrichment) and Stage III (PHA production). PHA-storing microorganisms were enriched in a sequencing batch reactor (SBR), operated at two different cycle lengths (CL-24; CL-12). Higher polymer recovery as well as VFA removal was achieved in CL-12 operation both in Stage II (16.3% dry cell weight (DCW); VFA removal, 84%) and Stage III (23.7% DCW; VFA removal, 88%). The PHA obtained was a co-polymer [P(3HB-co-3HV)] of PHB and PHV. The results obtained indicate that this integrated multistage process offers new opportunities to further leverage large scale PHA production with simultaneous waste remediation in the framework of biorefinery. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimization of hydrolysis and volatile fatty acids production from sugarcane filter cake: Effects of urea supplementation and sodium hydroxide pretreatment.

PubMed

Janke, Leandro; Leite, Athaydes; Batista, Karla; Weinrich, Sören; Sträuber, Heike; Nikolausz, Marcell; Nelles, Michael; Stinner, Walter

2016-01-01

Different methods for optimization the anaerobic digestion (AD) of sugarcane filter cake (FC) with a special focus on volatile fatty acids (VFA) production were studied. Sodium hydroxide (NaOH) pretreatment at different concentrations was investigated in batch experiments and the cumulative methane yields fitted to a dual-pool two-step model to provide an initial assessment on AD. The effects of nitrogen supplementation in form of urea and NaOH pretreatment for improved VFA production were evaluated in a semi-continuously operated reactor as well. The results indicated that higher NaOH concentrations during pretreatment accelerated the AD process and increased methane production in batch experiments. Nitrogen supplementation resulted in a VFA loss due to methane formation by buffering the pH value at nearly neutral conditions (∼ 6.7). However, the alkaline pretreatment with 6g NaOH/100g FCFM improved both the COD solubilization and the VFA yield by 37%, mainly consisted by n-butyric and acetic acids. Copyright © 2015 Elsevier Ltd. All rights reserved.

Near-infrared spectroscopy (NIRS) for a real time monitoring of the biogas process.

PubMed

Stockl, Andrea; Lichti, Fabian

2018-01-01

In this research project Near-infrared spectroscopy (NIRS) was applied to monitor the content of specific process parameters in anaerobic digestion. A laboratory scaled biogas digester was constantly fed every four hours with maize- and grass silage to keep a base load with an organic loading rate (OLR) of 2.5 kg oDM/m 3  ∗ d. Daily impact loads with shredded wheat up to an OLR of 8 kg oDM/m 3  ∗ d were added in order to generate peaks at the parameters tested. The developed calibration models are capable to show changes in process parameters like volatile fatty acids (VFA), propionic acid, total inorganic carbon (TIC) and the ratio of the volatile fatty acids to the carbonate buffer (VFA/TIC). Based on the calibration of the models for VFA and TIC, the values could be predicted with an R 2 of 0.94 and 0.97, respectively. Moreover, the residual prediction deviations were 4.0 and 6.0 for VFA and TIC, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Organic loading rate effect on the acidogenesis of cheese whey: a comparison between UASB and SBR reactors.

PubMed

Calero, R; Iglesias-Iglesias, R; Kennes, C; Veiga, M C

2017-09-16

Volatile fatty acids (VFA) production and degree of acidification (DA) were investigated in the anaerobic treatment of cheese whey by comparison of two processes: a continuous process using a laboratory upflow anaerobic sludge blanket (UASB) reactor and a discontinuous process using a sequencing batch reactor (SBR). The main purpose of this work was to study the organic loading rate (OLR) effect on the yield of VFA in two kinds of reactors. The predominant products in the acidogenic process in both reactors were: acetate, propionate, butyrate and valerate. The maximum DA obtained was 98% in an SBR at OLR of 2.7 g COD L -1 d -1 , and 97% in the UASB at OLR at 15.1 g COD L -1 d -1 . The results revealed that the UASB reactor was more efficient at a medium OLR with a higher VFA yield, while with the SBR reactor, the maximum acidification was obtained at a lower OLR with changes in the VFA profile at different OLRs applied.

Treatment of winery wastewater by an anaerobic sequencing batch reactor.

PubMed

Ruíz, C; Torrijos, M; Sousbie, P; Lebrato Martínez, J; Moletta, R; Delgenès, J P

2002-01-01

Treatment of winery wastewater was investigated using an anaerobic sequencing batch reactor (ASBR). Biogas production rate was monitored and permitted the automation of the bioreactor by a simple control system. The reactor was operated at an organic loading rate (ORL) around 8.6 gCOD/L.d with soluble chemical oxygen demand (COD) removal efficiency greater than 98%, hydraulic retention time (HRT) of 2.2 d and a specific organic loading rate (SOLR) of 0.96 gCOD/gVSS.d. The kinetics of COD and VFA removal were investigated for winery wastewater and for simple compounds such as ethanol, which is a major component of winery effluent, and acetate, which is the main volatile fatty acid (VFA) produced. The comparison of the profiles obtained with the 3 substrates shows that, overall, the acidification of the organic matter and the methanisation of the VFA follow zero order reactions, in the operating conditions of our study. The effect on the gas production rate resulted in two level periods separated by a sharp break when the acidification stage was finished and only the breaking down of the VFA continued.

Abdominal Subcutaneous Fat: A Favorable or Nonfunctional Fat Depot for Glucose Metabolism in Chinese Adults?

PubMed

Hou, Xuhong; Chen, Peizhu; Hu, Gang; Wei, Li; Jiao, Lei; Wang, Hongmei; Liang, Yebei; Bao, Yuqian; Jia, Weiping

2018-06-01

The objective of this study was to assess the associations of abdominal visceral and subcutaneous adipose tissue with blood glucose and beta-cell function. In this study, 11,223 participants without known diabetes were selected for this cross-sectional analysis. Visceral and subcutaneous fat area (VFA and SFA) were measured by magnetic resonance imaging. An oral glucose tolerance test was conducted, and beta-cell function was evaluated. Men had significantly larger VFA but smaller SFA than women. After controlling for age, linear regression showed that SFA was adversely associated with 0-minute, 30-minute, and 2-hour plasma glucose (PG) and early-, first- and second-phase disposition indices (DIs). After further adjustment for BMI and VFA, some associations of SFA with PG indices and DIs disappeared, while the other associations became significantly weaker in men (2-hour PG: 0.05 and DI 2nd : -0.05) or were reversed in women (0-minute, 30-minute, and 2-hour PG: from -0.07 to -0.04; DI 1st : 0.04, P < 0.05). After adjustment for age, BMI, and SFA, VFA was significantly and adversely associated with PG indices and DIs, with the largest standardized regression coefficients with 2-hour PG. The associations of SFA with blood glucose and beta-cell function were clinically insignificant in Chinese adults. VFA had the strongest association with 2-hour PG. © 2018 The Obesity Society.

Visceral adiposity is significantly associated with type 2 diabetes in middle-aged and elderly Chinese women: A cross-sectional study.

PubMed

Lv, Xiaofei; Zhou, Weiwei; Sun, Jichao; Lin, Ruhai; Ding, Lin; Xu, Min; Xu, Yu; Zhao, Zhiyun; Chen, Yuhong; Bi, Yufang; Lu, Jieli; Wang, Weiqing; Ning, Guang

2017-10-01

Previous studies suggest that visceral fat is associated with type 2 diabetes (T2D) independent of body mass index (BMI). However, epidemiological data about the relationship between visceral fat and T2D are rare in Chinese. The aim of the present study was to investigate whether visceral fat area (VFA) is associated with T2D beyond and above BMI in the Chinese population. The present community-based cross-sectional study was conducted in 2013 on 4126 individuals (2545 women, 1581 men) aged ≥ 40 years, with T2D diagnosed according to 1999 World Health Organization criteria. The VFA was measured by a fat area analyzer using bioelectrical impedance analysis. Participants were categorized into normal weight and overweight/obese groups according to BMI. Within each group, compared with women with below-median VFA, women with above-median VFA had a significantly increased risk of diabetes (odds ratio [OR] 1.88, 95% confidence interval [CI] 1.31-2.69 in the normal weight group; OR 2.10, 95% CI 1.54-2.85 in the overweight/obese group), whereas among men the corresponding associations were not significant in either group. Among women, after multivariable adjustment including BMI, each one standard deviation increase in VFA was significantly associated with a 45% higher risk of having T2D (OR 1.45, 95% CI 1.26-1.67), whereas among men BMI, not VFA, was independently associated with T2D (OR 1.18, 95% CI 1.02-1.37). Visceral fat was independently associated with T2D in women regardless of obesity status, whereas in men BMI may have a more important effect on T2D than visceral fat. © 2016 Ruijin Hospital, Shanghai Jiaotong University School of Medicine and John Wiley & Sons Australia, Ltd.

Abdominal subcutaneous adipose tissue: a favorable adipose depot for diabetes?

PubMed

Chen, Peizhu; Hou, Xuhong; Hu, Gang; Wei, Li; Jiao, Lei; Wang, Hongmei; Chen, Siyu; Wu, Jingzhu; Bao, Yuqian; Jia, Weiping

2018-06-26

Previous studies have documented that visceral adipose tissue is positively associated with the risk of diabetes. However, the association of subcutaneous adipose tissue with diabetes risk is still in dispute. We aimed to assess the associations between different adipose distributions and the risk of newly diagnosed diabetes in Chinese adults. The Shanghai Nicheng Cohort Study was conducted among Chinese adults aged 45-70 years. The baseline data of 12,137 participants were analyzed. Subcutaneous and visceral fat area (SFA and VFA) were measured by magnetic resonance imaging. Diabetes was newly diagnosed using a 75 g oral glucose tolerance test. The multivariable-adjusted odds ratios (OR) and 95% confidence intervals (CI) of newly diagnosed diabetes per 1-standard deviation increase in SFA and VFA were 1.29 (1.19-1.39) and 1.61 (1.49-1.74) in men, and 1.10 (1.03-1.18) and 1.56 (1.45-1.67) in women, respectively. However, the association between SFA and newly diagnosed diabetes disappeared in men and was reversed in women (OR 0.86 [95% CI, 0.78-0.94]) after additional adjustment for body mass index (BMI) and VFA. The positive association between VFA and newly diagnosed diabetes remained significant in both sexes after further adjustment for BMI and SFA. Areas under the receiver operating characteristic curve of newly diagnosed diabetes predicted by VFA (0.679 [95% CI, 0.659-0.699] for men and 0.707 [95% CI, 0.690-0.723] for women) were significantly larger than by the other adiposity indicators. SFA was beneficial for lower risk of newly diagnosed diabetes in women but was not associated with newly diagnosed diabetes in men after taking general obesity and visceral obesity into account. VFA, however, was associated with likelihood of newly diagnosed diabetes in both Chinese men and women.

Association between visceral obesity and sarcopenia and vitamin D deficiency in older Koreans: the Ansan Geriatric Study.

PubMed

Seo, Ji A; Cho, Hyunjoo; Eun, Chai R; Yoo, Hye J; Kim, Sin G; Choi, Kyung M; Baik, Sei H; Choi, Dong S; Park, Moon H; Han, Changsu; Kim, Nan H

2012-04-01

To investigate whether vitamin D levels are independently associated with visceral obesity, sarcopenia, or sarcopenic obesity. Cross-sectional. Population-based sample of elderly adults living in Ansan, Korea. Two hundred sixteen men and 268 women aged 65 and older. Serum 25-hydroxyvitamin D (25(OH)D) levels, visceral fat area (VFA) according to abdominal computed tomography scanning, and body composition (body fat percentage, appendicular skeletal muscle mass (ASM)) using dual-energy X-ray absorptiometry. Visceral obesity was defined as VFA of 100 cm(2) or greater and sarcopenia as ASM/height(2) more than 1 standard deviation (SD) below the sex-specific mean of a young reference group. The adjusted 25(OH)D level for men was negatively associated with systolic blood pressure, VFA, and body fat percentage but positively associated with ASM. In women, waist circumference, triglyceride levels, and VFA were negatively correlated with 25(OH)D levels. In the joint regression model, VFA and ASM were independently associated with 25(OH)D levels (β = -0.078, P = .01 and β = 0.087, P = .02, respectively) per 1SD difference in VFA and ASM in men but not women. When participants were categorized according to four visceral obesity and sarcopenia categories, adjusted mean 25(OH)D level was lower in men with visceral obesity than in men without but was not affected by the presence or absence of sarcopenia. Greater visceral fat and lower muscle mass were associated with lower 25(OH)D levels in elderly Korean men, suggesting that screening for vitamin D deficiency may be appropriate in older Koreans with visceral obesity or sarcopenia. Sarcopenic obesity as defined according to prespecified criteria did not have an additive association with 25(OH)D levels. © 2012, Copyright the Authors Journal compilation © 2012, The American Geriatrics Society.

Cross-sectional and longitudinal study of association between circulating thiobarbituric acid-reacting substance levels and clinicobiochemical parameters in 1,178 middle-aged Japanese men - the Amagasaki Visceral Fat Study

PubMed Central

2011-01-01

Background Circulating thiobarbituric acid-reacting substance (TBARS) levels, a marker of systemic oxidative stress, are predictive of cardiovascular events. However, they has not been evaluated in Japanese, especially with regard to the factors that contribute to the changes in circulating TBARS levels. We investigated the cross-sectional and longitudinal relationships between circulating TBARS levels and various clinicobiochemical parameters in middle-aged men. Methods In this population-based study (The Amagasaki Visceral Fat Study), 1,178 Japanese male urban workers who had undergone health check-ups in 2006, 2007 and 2008 and were not on medications for metabolic disorders during the follow-up period, were enrolled. Serum TBARS levels were measured by the method of Yagi. The estimated visceral fat area (eVFA) by bioelectrical impedance was measured annually. After health check-ups, subjects received health education with lifestyle modification by medical personnel. Results The number of cardiovascular risk factors (hypertension, hyperglycemia, low HDL-C, hypertriglyceridemia, hyperuricemia, hyper-LDL-C and impaired renal function) augmented with the increases in log-eVFA (p < 0.0001) and log-TBARS (p < 0.0001). The combination of TBARS and eVFA had a multiplicative effect on risk factor accumulation (F value = 79.1, p = 0.0065). Stepwise multiple regression analysis identified log-eVFA, as well as age, log-body mass index (BMI), LDL-C, log-adiponectin, γ-glutamyl transpeptidase (γ-GTP) and uric acid as significant determinants of log-TBARS. Stepwise multiple regression analysis identified one-year changes in eVFA as well as BMI, γ-GTP and estimated glomerular filtration rate (eGFR) as significant determinants of one-year change in TBARS, and biennial changes in eVFA as well as BMI and γ-GTP, eGFR as significant determinants of biennial change in TBARS. Conclusions The present study showed a significant cross-sectional and longitudinal correlation between TBARS and eVFA, as well as BMI and γ- GTP, eGFR. Visceral fat reduction may independently associate with the improvement in systemic ROS in middle-aged Japanese men. Trial Registration The Amagasaki Visceral Fat Study UMIN000002391. PMID:22108213

Oleaginous yeast Yarrowia lipolytica culture with synthetic and food waste-derived volatile fatty acids for lipid production.

PubMed

Gao, Ruiling; Li, Zifu; Zhou, Xiaoqin; Cheng, Shikun; Zheng, Lei

2017-01-01

The sustainability of microbial lipids production from traditional carbon sources, such as glucose or glycerol, is problematic given the high price of raw materials. Considerable efforts have been directed to minimize the cost and find new alternative carbon sources. Volatile fatty acids (VFAs) are especially attractive raw materials, because they can be produced from a variety of organic wastes fermentation. Therefore, the use of volatile fatty acids as carbon sources seems to be a feasible strategy for cost-effective microbial lipid production. Lipid accumulation in Y. lipolytica using synthetic and food waste-derived VFAs as substrates was systematically compared and evaluated in batch cultures. The highest lipid content obtained with acetic, butyric, and propionic acids reached 31.62 ± 0.91, 28.36 ± 0.74, and 28.91 ± 0.66%, respectively. High concentrations of VFA inhibited cell growth in the following order: butyric acid > propionic acid > acetic acid. Within a 30-day experimental period, Y. lipolytica could adapt up to 20 g/L acetic acid, whereas the corresponding concentration of propionic acid and butyric acid were 10 and 5 g/L, respectively. Cultures on a VFA mixture showed that the utilization of different types of VFA by Y. lipolytica was not synchronized but rather performed in a step-wise manner. Although yeast fermentation is an exothermic process, and the addition of VFA will directly affect the pH of the system by increasing environmental acidity, cultures at a cultivation temperature of 38 °C and uncontrolled pH demonstrated that Y. lipolytica had high tolerance in the high temperature and acidic environment when a low concentration (2.5 g/L) of either synthetic or food waste-derived VFA was used. However, batch cultures fed with food fermentate yielded lower lipid content (18.23 ± 1.12%) and lipid productivity (0.12 ± 0.02 g/L/day). The lipid composition obtained with synthetic and food waste-derived VFA was similar to commercial biodiesel feedstock. This work demonstrated the feasibility of utilizing synthetic and food waste-derived VFA for lipid production by Y. lipolytica . The good adaptability of Y. lipolytica to the high temperature and acidic environment further illustrated its considerable potential for practical application.

Microbial Fuels Cell-Based Biosensor for Toxicity Detection: A Review

PubMed Central

Zhou, Tuoyu; Han, Huawen; Liu, Pu; Xiong, Jian; Tian, Fake; Li, Xiangkai

2017-01-01

With the unprecedented deterioration of environmental quality, rapid recognition of toxic compounds is paramount for performing in situ real-time monitoring. Although several analytical techniques based on electrochemistry or biosensors have been developed for the detection of toxic compounds, most of them are time-consuming, inaccurate, or cumbersome for practical applications. More recently, microbial fuel cell (MFC)-based biosensors have drawn increasing interest due to their sustainability and cost-effectiveness, with applications ranging from the monitoring of anaerobic digestion process parameters (VFA) to water quality detection (e.g., COD, BOD). When a MFC runs under correct conditions, the voltage generated is correlated with the amount of a given substrate. Based on this linear relationship, several studies have demonstrated that MFC-based biosensors could detect heavy metals such as copper, chromium, or zinc, as well as organic compounds, including p-nitrophenol (PNP), formaldehyde and levofloxacin. Both bacterial consortia and single strains can be used to develop MFC-based biosensors. Biosensors with single strains show several advantages over systems integrating bacterial consortia, such as selectivity and stability. One of the limitations of such sensors is that the detection range usually exceeds the actual pollution level. Therefore, improving their sensitivity is the most important for widespread application. Nonetheless, MFC-based biosensors represent a promising approach towards single pollutant detection. PMID:28956857

Microbial Fuels Cell-Based Biosensor for Toxicity Detection: A Review.

PubMed

Zhou, Tuoyu; Han, Huawen; Liu, Pu; Xiong, Jian; Tian, Fake; Li, Xiangkai

2017-09-28

With the unprecedented deterioration of environmental quality, rapid recognition of toxic compounds is paramount for performing in situ real-time monitoring. Although several analytical techniques based on electrochemistry or biosensors have been developed for the detection of toxic compounds, most of them are time-consuming, inaccurate, or cumbersome for practical applications. More recently, microbial fuel cell (MFC)-based biosensors have drawn increasing interest due to their sustainability and cost-effectiveness, with applications ranging from the monitoring of anaerobic digestion process parameters (VFA) to water quality detection (e.g., COD, BOD). When a MFC runs under correct conditions, the voltage generated is correlated with the amount of a given substrate. Based on this linear relationship, several studies have demonstrated that MFC-based biosensors could detect heavy metals such as copper, chromium, or zinc, as well as organic compounds, including p -nitrophenol (PNP), formaldehyde and levofloxacin. Both bacterial consortia and single strains can be used to develop MFC-based biosensors. Biosensors with single strains show several advantages over systems integrating bacterial consortia, such as selectivity and stability. One of the limitations of such sensors is that the detection range usually exceeds the actual pollution level. Therefore, improving their sensitivity is the most important for widespread application. Nonetheless, MFC-based biosensors represent a promising approach towards single pollutant detection.

Effects of fescue toxicosis induced by endophyte-infected tall fescue seed on forestomach epithelial gene expression in Angus steers

USDA-ARS?s Scientific Manuscript database

A previous report demonstrated that steers exposed to an endophyte-infected tall fescue seed extract had altered rumen epithelial blood flow and decreased ruminal flux of VFA. Thus, this study was conducted to determine whether there are differences in gene expression related to VFA absorption betwe...

[Effect of Ce3+ on volatile fatty acid concentrations during anaerobic granular sludge digestion].

PubMed

Liang, Rui; Xia, Qing; Ding, Li-Li; Shi, Xiao-Lei; Zhao, Ming-Yu; Ren, Hong-Qiang

2009-04-15

Batch experiments were conducted to investigate the effect of Ce3+ on volatile fatty acid(VFA) concentrations by anaerobic granular sludge digestion using D-Glucose and acetic sodium as substrate in the state of stabilization and restart-up. Results show that when the concentration of Ce3+ is lower than 1 mg/L, VFA concentration decreases, which suggests the transformation of butyric acid to acetic acid and acetic acid to methane is promoted. When the concentration of Ce3+ is 1-10 mg/L, the bacterial activity decreases and decomposition of the acetic acid and butyric acid becomes more difficult compared with the control. Adding Ce3+ brings little change in the constitution of VFA: 96% of VFA is acetic acid and butyric acid, while the propionic acid accounts for less than 3%. With the acetic sodium as the sole carbon and energy source, adding 0.05 mg/L Ce3+ could accelerate acetate degradation. After being conserved for 4 months, the activity of the Ce-containing anaerobic granular sludge is higher than that of the Ce-free sludge. The present of Ce contributes to the restart-up of anaerobic reactors.

Development and validation of a simplified titration method for monitoring volatile fatty acids in anaerobic digestion.

PubMed

Sun, Hao; Guo, Jianbin; Wu, Shubiao; Liu, Fang; Dong, Renjie

2017-09-01

The volatile fatty acids (VFAs) concentration has been considered as one of the most sensitive process performance indicators in anaerobic digestion (AD) process. However, the accurate determination of VFAs concentration in AD processes normally requires advanced equipment and complex pretreatment procedures. A simplified method with fewer sample pretreatment procedures and improved accuracy is greatly needed, particularly for on-site application. This report outlines improvements to the Nordmann method, one of the most popular titrations used for VFA monitoring. The influence of ion and solid interfering subsystems in titrated samples on results accuracy was discussed. The total solid content in titrated samples was the main factor affecting accuracy in VFA monitoring. Moreover, a high linear correlation was established between the total solids contents and VFA measurement differences between the traditional Nordmann equation and gas chromatography (GC). Accordingly, a simplified titration method was developed and validated using a semi-continuous experiment of chicken manure anaerobic digestion with various organic loading rates. The good fitting of the results obtained by this method in comparison with GC results strongly supported the potential application of this method to VFA monitoring. Copyright © 2017. Published by Elsevier Ltd.

Enhancement of volatile fatty acid production by co-fermentation of food waste and excess sludge without pH control: The mechanism and microbial community analyses.

PubMed

Wu, Qing-Lian; Guo, Wan-Qian; Zheng, He-Shan; Luo, Hai-Chao; Feng, Xiao-Chi; Yin, Ren-Li; Ren, Nan-Qi

2016-09-01

The study provided a cost-effective and high-efficiency volatile fatty acid (VFA) production strategy by co-fermentation of food waste (FW) and excess sludge (ES) without artificial pH control. VFA production of 867.42mg COD/g-VS was obtained under the optimized condition: FW/ES 5, solid retention time 7d, organic loading rate 9g VS/L-d and temperature 40°C. Mechanism exploration revealed that the holistic biodegradability of substrate was greatly enhanced, and proper pH range (5.2-6.4) was formed by the high buffering capacity of the co-fermentation system itself, which effectively enhanced hydrolysis yield (63.04%) and acidification yield (83.46%) and inhibited methanogenesis. Moreover, microbial community analysis manifested that co-fermentation raised the relative abundances of hydrolytic and acidogenic bacteria including Clostridium, Sporanaerobacter, Tissierella and Bacillus, but suppressed the methanogen Anaerolineae, which also facilitated high VFA production. These results were of great guiding significance aiming for VFA recovery from FW and ES in large-scale. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hydrolytic and acidogenic fermentation potential of food waste with source segregated feces-without-urine as co-substrate.

PubMed

Rajagopal, Rajinikanth; Ahamed, Ashiq; Wang, Jing-Yuan

2014-09-01

This study explored a new approach to enhance VFA productivity from anaerobic co-digestion of food-waste (FW) with source-segregated brown-water (BW) [feces-without-urine]. Effort was made to separate urine and BW from the source (using no-mix-toilet) mainly to expedite further treatment and resource-recovery. Effect of alkaline-pH [B] and acclimatized acidogenic inoculum [C] on acidification efficiency was investigated and compared with raw FW+BW co-digestion [A]. Batch-assay results indicated that VFA productivity persists for 144-h with about 615%, 522% and 376% increase in VFA-COD, respectively for 3-conditions [A-C]; which accounted for 70%, 49% and 58% of CODs input, respectively. High butyric-acid was observed in [A] and [C], followed by acetic, propionic-acids; whereas, abundant acetic-acid (86% of TVFA) was observed in [B], which are the most favorable-forms for methane production or other value-added-products. For 144-h of acidification, this study validated the feasibility of maximizing VFA-yield by 7-12 times compared to FW or BW as a sole-substrate. Copyright © 2014 Elsevier Ltd. All rights reserved.

Anaerobic digestion of swine manure under natural zeolite addition: VFA evolution, cation variation, and related microbial diversity.

PubMed

Lin, Lin; Wan, Chunli; Liu, Xiang; Lei, Zhongfang; Lee, Duu-Jong; Zhang, Yi; Tay, Joo Hwa; Zhang, Zhenya

2013-12-01

Batch experiments were carried out on anaerobic digestion of swine manure under 10 % of total solids and 60 g/L of zeolite addition at 35 °C. Four distinctive volatile fatty acid (VFAs) evolution stages were observed during the anaerobic process, i.e., VFA accumulation, acetic acid (HAc) and butyric acid (HBu) utilization, propionic acid (HPr) and valeric acid (HVa) degradation, and VFA depletion. Large decreases in HAc/HBu and HPr/HVa occurred respectively at the first and second biogas peaks. Biogas yield increased by 20 % after zeolite addition, about 356 mL/g VSadded with accelerated soluble chemical oxygen demand degradation and VFA (especially HPr and HBu) consumption in addition to a shortened lag phase between the two biogas peaks. Compared with Ca(2+) and Mg(2+) (100-300 mg/L) released from zeolite, simultaneous K(+) and NH4 (+) (580-600 mg/L) adsorptions onto zeolite particles contributed more to the enhanced biogasification, resulting in alleviated inhibition effects of ammonium on acidogenesis and methanogenesis, respectively. All the identified anaerobes could be grouped into Bacteroidetes and Firmicutes, and zeolite addition had no significant influence on the microbial biodiversity in this study.

Hydrolysis and volatile fatty acids accumulation of waste activated sludge enhanced by the combined use of nitrite and alkaline pH.

PubMed

Huang, Cheng; Liu, Congcong; Sun, Xiuyun; Sun, Yinglu; Li, Rui; Li, Jiansheng; Shen, Jinyou; Han, Weiqing; Liu, Xiaodong; Wang, Lianjun

2015-12-01

Volatile fatty acids (VFAs) production from anaerobic digestion of waste activated sludge (WAS) is often limited by the slow hydrolysis and/or poor substrate availability. Increased attention has been given to enhance the hydrolysis and acidification of WAS recently. This study presented an efficient and green strategy based on the combined use of nitrite pretreatment and alkaline pH to stimulate hydrolysis and VFA accumulation from WAS. Results showed that both proteins and polysaccharides increased in the presence of nitrite, indicating the enhancement of sludge solubilization and hydrolysis processes. Mechanism investigations showed that nitrite pretreatment could disintegrate the sludge particle and disperse extracellular polymeric substances (EPS). Then, anaerobic digestion tests demonstrated VFA production increased with nitrite treatment. The maximal VFA accumulation was achieved with 0.1 g N/L nitrite dosage and pH 10.0 at a sludge retention time (SRT) of 7 days, which was much higher VFA production in comparison with the blank, sole nitrite pretreatment, or sole pH 10. The potential analysis suggested that the combined nitrite pretreatment and alkaline pH is capable of enhancing WAS digestion with a great benefit for biological nutrient removal (BNR).

Acidogenic digestion of food waste in a thermophilic leach bed reactor: Effect of pH and leachate recirculation rate on hydrolysis and volatile fatty acid production.

PubMed

Hussain, Abid; Filiatrault, Mélissa; Guiot, Serge R

2017-12-01

The effect of pH control (4, 5, 6, 7) on volatile fatty acids (VFA) production from food waste was investigated in a leach bed reactor (LBR) operated at 50°C. Stabilisation of pH at 7 resulted in hydrolysis yield of 530g soluble chemical oxygen demand (sCOD)/kg total volatile solids (TVS) added and VFA yield of 247gCOD/kg TVS added, which were highest among all pH tested. Butyric acid dominated the VFA mix (49-54%) at pH of 7 and 6, while acetate composed the primary VFA (41-56%) at pH of 4 and 5. A metabolic shift towards lactic acid production was observed at pH of 5. Improving leachate recirculation rate further improved the hydrolysis and degradation efficiency by 10-16% and the acidification yield to 340gCOD/kgTVS added. The butyric acid concentration of 16.8g/L obtained at neutral pH conditions is among the highest reported in literature. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Acidogenic fermentation of Scenedesmus sp.-AMDD: Comparison of volatile fatty acids yields between mesophilic and thermophilic conditions.

PubMed

Gruhn, Marvin; Frigon, Jean-Claude; Guiot, Serge R

2016-01-01

This study compared the acidogenic fermentation of Scenedesmus sp.-AMDD at laboratory-scale, under mesophilic (35°C) and thermophilic conditions (55°C). Preliminary batch tests were performed to evaluate best conditions for volatile fatty acid (VFA) production from microalgal biomass, with respect to the inoculum, pH and nutrients. The use of bovine manure as inoculum, the operating pH of 4.5 and the addition of a nutrient mix, resulted in a high VFA production of up to 222mgg(-1) total volatile solid (TVS), with a butyrate share of 27%. Both digesters displayed similar hydrolytic activity with 0.38±0.02 and 0.42±0.03 g soluble chemical oxygen demand (COD)g(-1) TVS for the digesters operated at 35 and 55°C, respectively. Mesophilic conditions were more favorable for VFA production, which reached 171±5, compared to 88±12 mg soluble CODg(-1) TVS added under thermophilic conditions (94% more). It was shown that in both digesters, butyrate was the predominant VFA. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Inclusion of psyllium in milk replacer for neonatal calves. 2. Effects on volatile fatty acid concentrations, microbial populations, and gastrointestinal tract size.

PubMed

Cannon, S J; Fahey, G C; Pope, L L; Bauer, L L; Wallace, R L; Miller, B L; Drackley, J K

2010-10-01

Fermentable fibers such as psyllium increase volatile fatty acid (VFA) concentrations in the lower digestive tract and increase the gastrointestinal tract (GIT) mass of many mammals. We reasoned that psyllium inclusion in milk replacer might produce similar effects in neonatal dairy calves, which could lead to improved growth and health. Male Holstein calves were fed a milk replacer (22% crude protein, 20% fat) either without or with psyllium (1.1% of dry matter, DM) from 2 d through 28 d of age. Milk replacer was reconstituted to 12.5% DM and fed at 12% of calf body weight, adjusted weekly. Water was offered ad libitum but no starter was fed. Three calves per treatment were harvested weekly to sample digesta from the reticulo-rumen, abomasum, jejunum, proximal colon, and distal colon, and to determine length and mass of GIT components. Psyllium in milk replacer increased the proportion of butyrate in reticulo-rumen contents from 2.4 to 3.2% of total but did not affect total VFA concentrations. Total VFA concentrations were very low in the jejunum but psyllium tended to increase total VFA, acetate, and valerate concentrations; valerate accounted for 15.9 and 16.7% of total VFA (molar basis) for control and psyllium calves, respectively. Psyllium increased total VFA concentrations in the proximal and distal colon by 104.4 and 45.6%, respectively, but had little effect on the profile of VFA. Psyllium in milk replacer increased populations of bifidobacteria (from 9.7 to 10.3 log(10) cfu/g of DM) and lactobacilli (from 8.2 to 9.4 log(10) cfu/g of DM) in the reticulo-rumen, but did not affect populations in jejunum or colon. Calves fed psyllium had 12.0% greater total GIT mass and 9.4% greater GIT as a percentage of body weight. Psyllium tended to increase mass of the reticulo-rumen and significantly increased mass of duodenum (34.2%), jejunum (14.5%), and colon (14.6%). Density of intestinal tissues from calves fed psyllium-supplemented milk replacer was 25.9% greater in the jejunum and 25.3% greater in the ileum, and tended to be greater in duodenum and colon than tissue from control calves. Supplementation of psyllium to milk replacer increased fermentation in the colon, mass of the total GIT, and populations of bifidobacteria and lactobacilli in the reticulo-rumen. Copyright © 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

In vitro fermentation characteristics of diets with different forage/concentrate ratios: comparison of rumen and faecal inocula.

PubMed

Zicarelli, Fabio; Calabrò, Serena; Cutrignelli, Monica I; Infascelli, Federico; Tudisco, Raffaella; Bovera, Fulvia; Piccolo, Vincenzo

2011-05-01

The aim of this trial was to evaluate the replacement of rumen fluid with faeces as inoculum in studying the in vitro fermentation characteristics of diets for ruminants using the in vitro gas production technique. Six iso-protein diets with different forage/concentrate ratios were incubated with rumen fluid (RI) or faeces (FI) collected from sheep. Most of the fermentation parameters were influenced by diet and inoculum (P < 0.01). With both inocula, organic matter degradability (dOM), cumulative gas production (OMCV) and maximum fermentation rate (R(max) ) increased as the amount of concentrate in the diet increased. R(max) was lower with FI vs RI (P < 0.01); dOM was higher with FI vs RI and the diet × inoculum interaction was significant. As expected, with both inocula, R(max) increased as the neutral detergent fibre content of the diet decreased. Significant correlations were obtained using both inocula between OMCV/dOM and gas/volatile fatty acid (VFA), while the correlation VFA/dOM was significant only with FI. The microbial biomass yield calculated by stoichiometric analysis for all diets was higher with FI vs RI. With FI the organic matter used for microbial growth showed an overall decreasing trend as the amount of concentrate in the diet increased. The results indicate that both faeces and rumen fluid from sheep have the potential to be used as inoculum for the in vitro gas production technique. Copyright © 2011 Society of Chemical Industry.

Dietary marker effects on fecal microbial ecology, fecal VFA, nutrient digestibility coefficients, and growth performance in finishing pigs

USDA-ARS?s Scientific Manuscript database

Use of indigestible markers such as Cr2O3, Fe2O3, and TiO2 are commonly used in animal studies to evaluate rate of passage and nutrient digestibility. Yet nothing is known relative to their potential impact on fecal microbial ecology and subsequent VFA generation. Two experiments utilizing a total o...

Application of the World Health Organization Fracture Risk Assessment Tool to predict need for dual-energy X-ray absorptiometry scanning in postmenopausal women.

PubMed

Chao, An-Shine; Chen, Fang-Ping; Lin, Yu-Ching; Huang, Ting-Shuo; Fan, Chih-Ming; Yu, Yu-Wei

2015-12-01

To evaluate the efficacy of the World Health Organization Fracture Risk Assessment Tool, excluding bone mineral density (pre-BMD FRAX), in identifying Taiwanese postmenopausal women needing dual-energy X-ray absorptiometry (DXA) examination for further treatment. The pre-BMD FRAX score was calculated for 231 postmenopausal women who participated in public health education workshops in the local Keelung community, Taiwan. DXA scanning and vertebral fracture assessment (VFA) were arranged for women classified as intermediate or high risk for fracture using the pre-BMD FRAX fracture probability. Pre-BMD FRAX classified 26 women as intermediate risk and 37 as having high risk for fracture. Subsequent DXA scans for these 63 women showed that 36 were osteoporotic, 19 were osteopenic, and eight had normal bone density. Concurrent VFA revealed 25 spine factures in which 14 were osteoporotic, seven were osteopenic, and four had normal bone density. The efficacy of the pre-BMD FRAX score to identify those patients with low bone mass by DXA was 87.3% (55/63). When VFA was combined with BMD to identify those patients with high risk (osteopenia, osteoporosis, or spinal fracture), the efficacy of the pre-BMD score increased to 93.7% (59/63). According to the National Osteoporosis Foundation, the overall concordance between pre-BMD FRAX and BMD, expressed through the kappa index, was 0.967. Compared with the evaluation when BMD was used alone, there was a significant increase in efficacy in identifying women who need treatment using BMD plus VFA or FRAX plus BMD. Furthermore, the highest efficacy was achieved when FRAX with BMD and VFA was used. The pre-BMD FRAX score not only efficiently predicts postmenopausal patients who are potentially at risk and might require treatment but also reduces unnecessary DXA use. Concurrent VFA during DXA use increases spine fracture detection. This improvement in diagnostic efficacy allows clinicians to provide the most appropriate therapeutic recommendation. Copyright © 2015. Published by Elsevier B.V.

Comparison of long-term voice outcomes after vocal fold augmentation using autologous fat injection by direct microlaryngoscopy versus office-based calcium hydroxylapatite injection.

PubMed

Zeleník, Karol; Walderová, Radana; Kučová, Hana; Jančatová, Debora; Komínek, Pavel

2017-08-01

The objective is to compare the long-term voice outcomes of vocal fold augmentation (VFA) using autologous fat injection via direct microlaryngoscopy versus office-based calcium hydroxylapatite (CaHA) injection. Patients with glottal insufficiency and a gap no greater than 3 mm caused by unilateral vocal fold paralysis or vocal fold atrophy were prospectively recruited to the study from September 2012 to September 2015. From September 2012 to May 2014, VFA was only performed using autologous fat via direct microlaryngoscopy under general anesthesia (N = 14). From May 2014 to September 2015, VFA was performed as an office-based procedure using a transoral approach to inject CaHA (N = 17). Videolaryngostroboscopic evaluation, subjective satisfaction with voice, voice handicap index (VHI), and maximal phonation time (MPT) were analyzed pre-injection and 12 months after VFA. A total of 31 patients were analyzed. One year after VFA, 67.8% of the patients were satisfied with their voice, with no significant difference between groups (P = 0.247). The mean improvement in VHI in the autologous fat group was 31.6 ± 16.82 versus 35 ± 27.24 in the CaHA group (P = 0.664). MPT improvement was also similar in the two groups: 5.5 ± 2.52 for the autologous fat group versus 6.0 ± 3.98 for the CaHA group (P = 0.823). Both autologous fat injection via direct microlaryngoscopy and office-based CaHA injection have good long-term results. There were no differences in the treatment results of the two procedures 1 year after injection.

Effects of Branched-chain Amino Acids on In vitro Ruminal Fermentation of Wheat Straw

PubMed Central

Zhang, Hui Ling; Chen, Yong; Xu, Xiao Li; Yang, Yu Xia

2013-01-01

This study investigates the effects of three branched-chain amino acids (BCAA; valine, leucine, and isoleucine) on the in vitro ruminal fermentation of wheat straw using batch cultures of mixed ruminal microorganisms. BCAA were added to the buffered ruminal fluid at a concentration of 0, 2, 4, 7, or 10 mmol/L. After 72 h of anaerobic incubation, pH, volatile fatty acids (VFA), and ammonia nitrogen (NH3-N) in the ruminal fluid were determined. Dry matter (DM) and neutral detergent fiber (NDF) degradability were calculated after determining the DM and NDF in the original material and in the residue after incubation. The addition of valine, leucine, or isoleucine increased the total VFA yields (p≤0.001). However, the total VFA yields did not increase with the increase of BCAA supplement level. Total branched-chain VFA yields linearly increased as the supplemental amount of BCAA increased (p<0.001). The molar proportions of acetate and propionate decreased, whereas that of butyrate increased with the addition of valine and isoleucine (p<0.05). Moreover, the proportions of propionate and butyrate decreased (p<0.01) with the addition of leucine. Meanwhile, the molar proportions of isobutyrate were increased and linearly decreased (p<0.001) by valine and leucine, respectively. The addition of leucine or isoleucine resulted in a linear (p<0.001) increase in the molar proportions of isovalerate. The degradability of NDF achieved the maximum when valine or isoleucine was added at 2 mmol/L. The results suggest that low concentrations of BCAA (2 mmol/L) allow more efficient regulation of ruminal fermentation in vitro, as indicated by higher VFA yield and NDF degradability. Therefore, the optimum initial dose of BCAA for in vitro ruminal fermentation is 2 mmol/L. PMID:25049818

The anatomy of object recognition--visual form agnosia caused by medial occipitotemporal stroke.

PubMed

Karnath, Hans-Otto; Rüter, Johannes; Mandler, André; Himmelbach, Marc

2009-05-06

The influential model on visual information processing by Milner and Goodale (1995) has suggested a dissociation between action- and perception-related processing in a dorsal versus ventral stream projection. It was inspired substantially by the observation of a double dissociation of disturbed visual action versus perception in patients with optic ataxia on the one hand and patients with visual form agnosia (VFA) on the other. Unfortunately, almost all cases with VFA reported so far suffered from inhalational intoxication, the majority with carbon monoxide (CO). Since CO induces a diffuse and widespread pattern of neuronal and white matter damage throughout the whole brain, precise conclusions from these patients with VFA on the selective role of ventral stream structures for shape and orientation perception were difficult. Here, we report patient J.S., who demonstrated VFA after a well circumscribed brain lesion due to stroke etiology. Like the famous patient D.F. with VFA after CO intoxication studied by Milner, Goodale, and coworkers (Goodale et al., 1991, 1994; Milner et al., 1991; Servos et al., 1995; Mon-Williams et al., 2001a,b; Wann et al., 2001; Westwood et al., 2002; McIntosh et al., 2004; Schenk and Milner, 2006), J.S. showed an obvious dissociation between disturbed visual perception of shape and orientation information on the one side and preserved visuomotor abilities based on the same information on the other. In both hemispheres, damage primarily affected the fusiform and the lingual gyri as well as the adjacent posterior cingulate gyrus. We conclude that these medial structures of the ventral occipitotemporal cortex are integral for the normal flow of shape and of contour information into the ventral stream system allowing to recognize objects.

Polyhydroxyalkanoate Production on Waste Water Treatment Plants: Process Scheme, Operating Conditions and Potential Analysis for German and European Municipal Waste Water Treatment Plants

PubMed Central

Pittmann, Timo; Steinmetz, Heidrun

2017-01-01

This work describes the production of polyhydroxyalkanoates (PHA) as a side stream process on a municipal waste water treatment plant (WWTP) and a subsequent analysis of the production potential in Germany and the European Union (EU). Therefore, tests with different types of sludge from a WWTP were investigated regarding their volatile fatty acids (VFA) production-potential. Afterwards, primary sludge was used as substrate to test a series of operating conditions (temperature, pH, retention time (RT) and withdrawal (WD)) in order to find suitable settings for a high and stable VFA production. In a second step, various tests regarding a high PHA production and stable PHA composition to determine the influence of substrate concentration, temperature, pH and cycle time of an installed feast/famine-regime were conducted. Experiments with a semi-continuous reactor operation showed that a short RT of 4 days and a small WD of 25% at pH = 6 and around 30 °C is preferable for a high VFA production rate (PR) of 1913 mgVFA/(L×d) and a stable VFA composition. A high PHA production up to 28.4% of cell dry weight (CDW) was reached at lower substrate concentration, 20 °C, neutral pH-value and a 24 h cycle time. A final step a potential analysis, based on the results and detailed data from German waste water treatment plants, showed that the theoretically possible production of biopolymers in Germany amounts to more than 19% of the 2016 worldwide biopolymer production. In addition, a profound estimation regarding the EU showed that in theory about 120% of the worldwide biopolymer production (in 2016) could be produced on European waste water treatment plants. PMID:28952533

A degradation model for high kitchen waste content municipal solid waste.

PubMed

Chen, Yunmin; Guo, Ruyang; Li, Yu-Chao; Liu, Hailong; Zhan, Tony Liangtong

2016-12-01

Municipal solid waste (MSW) in developing countries has a high content of kitchen waste (KW), and therefore contains large quantities of water and non-hollocellulose degradable organics. The degradation of high KW content MSW cannot be well simulated by the existing degradation models, which are mostly established for low KW content MSW in developed countries. This paper presents a two-stage anaerobic degradation model for high KW content MSW with degradations of hollocellulose, sugars, proteins and lipids considered. The ranges of the proportions of chemical compounds in MSW components are summarized with the recommended values given. Waste components are grouped into rapidly or slowly degradable categories in terms of the degradation rates under optimal water conditions for degradation. In the proposed model, the unionized VFA inhibitions of hydrolysis/acidogenesis and methanogenesis are considered as well as the pH inhibition of methanogenesis. Both modest and serious VFA inhibitions can be modeled by the proposed model. Default values for the parameters in the proposed method can be used for predictions of degradations of both low and high KW content MSW. The proposed model was verified by simulating two laboratory experiments, in which low and high KW content MSW were used, respectively. The simulated results are in good agreement with the measured data of the experiments. The results show that under low VFA concentrations, the pH inhibition of methanogenesis is the main inhibition to be considered, while the inhibitions of both hydrolysis/acidogenesis and methanogenesis caused by unionized VFA are significant under high VFA concentrations. The model is also used to compare the degradation behaviors of low and high KW content MSW under a favorable environmental condition, and it shows that the gas potential of high KW content MSW releases more quickly. Copyright © 2016 Elsevier Ltd. All rights reserved.

Visceral adiposity and skeletal muscle mass are independently and synergistically associated with left ventricular structure and function: the Korean Genome and Epidemiology Study.

PubMed

Park, Juri; Kim, Nan Hee; Kim, Seong Hwan; Kim, Jin-Seok; Kim, Yong Hyun; Lim, Hong Euy; Kim, Eung Ju; Na, Jin Oh; Cho, Goo-Yeong; Baik, Inkyung; Kim, Doo Man; Choi, Dong Seop; Lee, Seung Ku; Shin, Chol

2014-10-20

Obesity and low muscle mass may coexist as age-related changes in body composition. We aimed to investigate the effect of visceral adiposity and skeletal muscle mass on left ventricular (LV) structure and function in the general population. A total of 1941 participants without known cardiovascular disease were enrolled from the Korean Genome and Epidemiology Study. Visceral fat area (VFA) was assessed by computed tomography. Appendicular skeletal muscle mass (ASM) was estimated by dual-energy X-ray absorptiometry and was used as a percentage of body weight (ASM/Wt). LV structure and function were assessed by tissue Doppler imaging (TDI) echocardiography. Across VFA tertiles, ASM increased, but ASM/Wt decreased (all P<0.001). In multivariate models adjusted for conventional cardiovascular risk factors, LV mass index and LV diastolic parameters, such as left atrial dimension, TDI Ea velocity, and E/Ea ratio, were significantly impaired as VFA increased. On the other hand, an increase in ASM/Wt was associated with a decrease in LV mass index and improvement of LV diastolic parameters. With regard to LV mass index and TDI Ea velocity, VFA and ASM/Wt showed synergistic effects (all P interaction<0.05). When both VFA and ASM/Wt were simultaneously included in the same model, both remained independent predictors of LV mass index and TDI Ea velocity. More visceral fat and less muscle mass are independently and synergistically associated with an increase in LV mass index and impairment of LV diastolic parameters. Further research is needed to explore the complex mechanisms underlying these associations. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Clinical impact of sarcopenia on prognosis in pancreatic ductal adenocarcinoma: A retrospective cohort study.

PubMed

Ninomiya, Go; Fujii, Tsutomu; Yamada, Suguru; Yabusaki, Norimitsu; Suzuki, Kojiro; Iwata, Naoki; Kanda, Mitsuro; Hayashi, Masamichi; Tanaka, Chie; Nakayama, Goro; Sugimoto, Hiroyuki; Koike, Masahiko; Fujiwara, Michitaka; Kodera, Yasuhiro

2017-03-01

To investigate the impact of the body composition such as skeletal muscle, visceral fat and body mass index (BMI) on patients with resected pancreatic ductal adenocarcinoma (PDAC). A total of 265 patients who underwent curative surgery for PDAC were examined in this study. The total skeletal muscle and fat tissue areas were evaluated in a single image obtained at the third lumber vertebra during a preoperative computed tomography (CT) scan. The patients were assigned to either the sarcopenia or non-sarcopenia group based on their skeletal muscle index (SMI) and classified into high visceral fat area (H-VFA) or low VFA (L-VFA) groups. The association of clinicopathological features and prognosis with the body composition were statistically analyzed. There were 170 patients (64.2%) with sarcopenia. The median survival time (MST) was 23.7 months for sarcopenia patients and 25.8 months for patients without sarcopenia. The MST was 24.4 months for H-VFA patients and 25.8 months for L-VFA patients. However, sarcopenia patients with BMI ≥22 exhibited significantly poorer survival than patients without sarcopenia (MST: 19.2 vs. 35.4 months, P = 0.025). There was a significant difference between patients with and without sarcopenia who did not receive chemotherapy (5-year survival rate: 0% vs. 68.3%, P = 0.003). The multivariate analysis revealed that tumor size, positive dissected peripancreatic tissue margin, and sarcopenia were independent prognostic factors. Sarcopenia is an independent prognostic factor in PDAC patients with a BMI ≥22. Therefore, evaluating skeletal muscle mass may be a simple and useful approach for predicting patient prognosis. Copyright © 2017 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

Rates of production of acetate, propionate, and butyrate in the rumen of lactating dairy cows given normal and low-roughage diets.

PubMed

Sutton, J D; Dhanoa, M S; Morant, S V; France, J; Napper, D J; Schuller, E

2003-11-01

Five lactating dairy cows with a permanent cannula in the rumen were given (kg DM/d) a normal diet (7.8 concentrates, 5.1 hay) or a low-roughage (LR) diet (11.5 concentrates, 1.2 hay) in two meals daily in a two-period crossover design. Milk fat (g/kg) was severely reduced on diet LR. To measure rates of production of individual volatile fatty acids (VFA) in the rumen, 0.5 mCi 1-(14)C-acetic acid, 2-(14)C-propionic acid, or 1-(14)C-n-butyric acid were infused into the rumen for 22 h at intervals of 2 to 6 d; rumen samples were taken over the last 12 h. To measure rumen volume, we infused Cr-EDTA into the rumen continuously, and polyethylene glycol was injected 2 h before the morning feed. Results were very variable, so volumes measured by rumen emptying were used instead. Net production of propionic acid more than doubled on LR, but acetate and butyrate production was only numerically lower. Net production rates pooled across both diets were significantly related to concentrations for each VFA. Molar proportions of net production were only slightly higher than molar proportions of concentrations for acetate and propionate but were lower for butyrate. The net energy value (MJ/d) of production of the three VFA increased from 89.5 on normal to 109.1 on LR, equivalent to 55 and 64% of digestible energy, respectively. Fully interchanging, three-pool models of VFA C fluxes are presented. It is concluded that net production rates of VFA can be measured in non-steady states without the need to measure rumen volumes.

Volatile fatty acids production from marine macroalgae by anaerobic fermentation.

PubMed

Pham, Thi Nhan; Nam, Woo Joong; Jeon, Young Joong; Yoon, Hyon Hee

2012-11-01

Volatile fatty acids (VFAs) were produced from the marine macroalgae, Laminaria japonica, Pachymeniopsis elliptica, and Enteromorpha crinite by anaerobic fermentation using a microbial community derived from a municipal wastewater treatment plant. Methanogen inhibitor (iodoform), pH control, substrate concentration, and alkaline and thermal pretreatments affected VFA productivity. Acetic, propionic, and butyric acids were the main products. A maximum VFA concentration of 15.2g/L was obtained from 50 g/L of L. japonica in three days at 35°C and pH 6.5-7.0. Pretreatment with 0.5 N NaOH improved VFA productivity by 56% compared to control. The result shows the applicability of marine macroalgae as biomass feedstock for the production of VFAs which can be converted to mixed alcohol fuels. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effects of free ammonia on volatile fatty acid accumulation and process performance in the anaerobic digestion of two typical bio-wastes.

PubMed

Shi, Xuchuan; Lin, Jia; Zuo, Jiane; Li, Peng; Li, Xiaoxia; Guo, Xianglin

2017-05-01

The effect of free ammonia on volatile fatty acid (VFA) accumulation and process instability was studied using a lab-scale anaerobic digester fed by two typical bio-wastes: fruit and vegetable waste (FVW) and food waste (FW) at 35°C with an organic loading rate (OLR) of 3.0kg VS/(m 3 ·day). The inhibitory effects of free ammonia on methanogenesis were observed due to the low C/N ratio of each substrate (15.6 and 17.2, respectively). A high concentration of free ammonia inhibited methanogenesis resulting in the accumulation of VFAs and a low methane yield. In the inhibited state, acetate accumulated more quickly than propionate and was the main type of accumulated VFA. The co-accumulation of ammonia and VFAs led to an "inhibited steady state" and the ammonia was the main inhibitory substance that triggered the process perturbation. By statistical significance test and VFA fluctuation ratio analysis, the free ammonia inhibition threshold was identified as 45mg/L. Moreover, propionate, iso-butyrate and valerate were determined to be the three most sensitive VFA parameters that were subject to ammonia inhibition. Copyright © 2016. Published by Elsevier B.V.

Monitoring and control of the biogas process based on propionate concentration using online VFA measurement.

PubMed

Boe, Kanokwan; Steyer, Jean-Philippe; Angelidaki, Irini

2008-01-01

Simple logic control algorithms were tested for automatic control of a lab-scale CSTR manure digester. Using an online VFA monitoring system, propionate concentration in the reactor was used as parameter for control of the biogas process. The propionate concentration was kept below a threshold of 10 mM by manipulating the feed flow. Other online parameters such as pH, biogas production, total VFA, and other individual VFA were also measured to examine process performance. The experimental results showed that a simple logic control can successfully prevent the reactor from overload, but with fluctuations of the propionate level due to the nature of control approach. The fluctuation of propionate concentration could be reduced, by adding a lower feed flow limit into the control algorithm to prevent undershooting of propionate response. It was found that use of the biogas production as a main control parameter, rather than propionate can give a more stable process, since propionate was very persistent and only responded very slowly to the decrease of the feed flow which lead to high fluctuation of biogas production. Propionate, however, was still an excellent parameter to indicate process stress under gradual overload and thus recommended as an alarm in the control algorithm. Copyright IWA Publishing 2008.

Relationships between body fat accumulation, aerobic capacity and insulin resistance in Japanese participants.

PubMed

Yoshimura, Eiichi; Kumahara, Hideaki; Tobina, Takuro; Ayabe, Makoto; Matono, Sakiko; Anzai, Keizo; Higaki, Yasuki; Kiyonaga, Akira; Tanaka, Hiroaki

2011-01-01

This study evaluated the relationships between body fat accumulation, aerobic capacity and insulin resistance (HOMA-IR) in 61 Japanese participants. The participants were middle-aged to elderly (age: 33-73; BMI: 21.6-38.5). Body fat mass (FM) was evaluated by hydrostatic weighing. Computed tomography was used to evaluate visceral and subcutaneous fat areas (VFA and SFA), liver to spleen ratio (L/S), and low-density muscle area (LDMA). To assess aerobic capacity, VO2 at the lactate threshold (VO2@LT) and VO2 peak were measured using a bicycle ergometer. FM, VFA, SFA, LDMA and L/S significantly correlated with HOMA-IR, but VO2@LT and VO2 peak did not. Analysis of covariance after adjustment for VFA or other body fat distribution and aerobic capacity showed that HOMA-IR had a significant linear trend across the tertile groups of L/S. However, for FM, VFA, SFA, LDMA and VO2@LT or VO2 peak, no significant trend was observed between the tertiles and insulin resistance. Ectopic fat deposition in the liver may influence insulin resistance independently of other body fat accumulation and aerobic capacity in Japanese participants. © 2011 Asian Oceanian Association for the Study of Obesity . Published by Elsevier Ltd. All rights reserved.

Optimum design and operation of primary sludge fermentation schemes for volatile fatty acids production.

PubMed

Chanona, J; Ribes, J; Seco, A; Ferrer, J

2006-01-01

This paper presents a model-knowledge based algorithm for optimising the primary sludge fermentation process design and operation. This is a recently used method to obtain the volatile fatty acids (VFA), needed to improve biological nutrient removal processes, directly from the raw wastewater. The proposed algorithm consists in a heuristic reasoning algorithm based on the expert knowledge of the process. Only effluent VFA and the sludge blanket height (SBH) have to be set as design criteria, and the optimisation algorithm obtains the minimum return sludge and waste sludge flow rates which fulfil those design criteria. A pilot plant fed with municipal raw wastewater was operated in order to obtain experimental results supporting the developed algorithm groundwork. The experimental results indicate that when SBH was increased, higher solids retention time was obtained in the settler and VFA production increased. Higher recirculation flow-rates resulted in higher VFA production too. Finally, the developed algorithm has been tested by simulating different design conditions with very good results. It has been able to find the optimal operation conditions in all cases on which preset design conditions could be achieved. Furthermore, this is a general algorithm that can be applied to any fermentation-elutriation scheme with or without fermentation reactor.

Neil Armstrong Family Memorial Service

NASA Image and Video Library

2012-08-31

U.S. Navy F/A-18 jets from Strike Fighter Squadron (VFA) 106 and Strike Fighter Squadron (VFA) 34, from Naval Air Station Oceana (Va.) fly in a "Missing Man" formation over the Camargo Club following a memorial service celebrating the life of Neil Armstrong, Friday, Aug. 31, 2012, in Cincinnati. Armstrong, the first man to walk on the moon during the 1969 Apollo 11 mission, died Saturday, Aug. 25. He was 82. Photo Credit: (NASA/Bill Ingalls)

Comparative Demonstration of Active and Semi-Passive In Situ Bioremediation Approaches for Perchlorate-Impacted Groundwater at Longhorn Army Ammunitions Plant

DTIC Science & Technology

2009-01-01

lactate, citric acid , or ethanol have been used in field applications. Biomass grows rapidly during the active phase when high concentrations of...6.7.4 Results of Oxidation Reduction Potential (ORP) Monitoring.............39 6.7.5 Results of Volatile Fatty Acids (VFA) Analysis...trinitrotoluene USEPA U.S. Environmental Protection Agency VC vinyl chloride VFA volatile fatty acid VOC volatile organic compounds Technical

A fuzzy-logic-based controller for methane production in anaerobic fixed-film reactors.

PubMed

Robles, A; Latrille, E; Ruano, M V; Steyer, J P

2017-01-01

The main objective of this work was to develop a controller for biogas production in continuous anaerobic fixed-bed reactors, which used effluent total volatile fatty acids (VFA) concentration as control input in order to prevent process acidification at closed loop. To this aim, a fuzzy-logic-based control system was developed, tuned and validated in an anaerobic fixed-bed reactor at pilot scale that treated industrial winery wastewater. The proposed controller varied the flow rate of wastewater entering the system as a function of the gaseous outflow rate of methane and VFA concentration. Simulation results show that the proposed controller is capable to achieve great process stability even when operating at high VFA concentrations. Pilot results showed the potential of this control approach to maintain the process working properly under similar conditions to the ones expected at full-scale plants.

The effects of starch and rapidly degradable dry matter from concentrate on ruminal digestion in dairy cows fed corn silage-based diets with fixed forage proportion.

PubMed

Lechartier, C; Peyraud, J-L

2011-05-01

This study investigated the effects of the type (starch vs. nonstarch) and rate of ruminal degradation of carbohydrates from the concentrate on digestion in dairy cows fed corn silage-based diets. Six ruminally cannulated cows were assigned to 6 treatments in a 6 × 6 Latin square design. Treatments were arranged in a 3 × 2 factorial design. Two starch levels [25 and 41% dry matter (DM) for low starch (LS) and high starch (HS) diets, respectively] were obtained by replacing starch-rich feedstuffs by nonstarch feedstuffs. These starch levels were combined with slowly, moderately, and rapidly rumen-degradable feedstuffs to obtain 3 levels of rapidly degradable carbohydrates from concentrate (18, 23, and 28% DM). These levels were estimated from the DM disappearance of concentrate after 4h of in sacco incubation (CRDM). Wheat and corn grain were used as rapidly degradable and slowly degradable starch feedstuffs, respectively. Soybean hulls and citrus pulp were used as slowly degradable and rapidly degradable nonstarch feedstuffs, respectively. No interaction effect was found between dietary starch content and CRDM on pH range, volatile fatty acid (VFA) range, or VFA profile. Increasing CRDM led to a linear decrease in acetate-to-propionate ratio (from 2.7 to 2.1), and a linear increase in the pH and VFA ranges (from 0.86 to 1.12 pH units and from 34 to 56mM, respectively). Feeding HS diets decreased acetate-to-propionate ratio (2.6 vs. 2.0) and increased pH range (0.89 vs. 1.04 pH units), but had no effect on VFA range. Increasing CRDM linearly decreased mean ruminal pH in LS diets but linearly increased mean ruminal pH in HS diets. Fibrolytic activity was unaffected in LS diets but decreased strongly in HS diets (from 62 to 50%). These findings suggest that pH regulation differs on a short-term and on a longer-term basis. In the short-term, increasing CRDM increased the rate of VFA production, which may have been partly buffered under LS diets due to the higher cation exchange capacity of nonstarch feedstuffs compared with starch-rich feedstuffs. In the longer term, feeding starch reduced fibrolytic activity, which may have led to lower total VFA production and higher mean pH. The results of this experiment clearly show that both fermentative characteristics of the concentrate and dietary starch content should be taken into account when formulating diets to prevent subacute ruminal acidosis and to predict VFA profile. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The relationship between rumen acidosis resistance and expression of genes involved in regulation of intracellular pH and butyrate metabolism of ruminal epithelial cells in steers.

PubMed

Schlau, N; Guan, L L; Oba, M

2012-10-01

Past research has focused on the prevention and management of subacute rumen acidosis by manipulating the ration; however, the severity of acidosis varies even among animals fed a common high-grain diet. The objectives of this study were to compare the ruminal volatile fatty acid (VFA) profile and expression of genes involved in the metabolism of butyrate, the VFA most extensively metabolized by the ruminal epithelium, and intracellular pH regulation in ruminal epithelial cells between acidosis-resistant (AR) and acidosis-susceptible (AS) steers. Acidosis indexes (area per day under pH 5.8 divided by dry matter intake) were measured for 17 steers fed a common high-grain diet, and the 3 steers with the lowest (1.4 ± 1.2 pH∙min/kg) and the 3 with the highest values (23.9 ± 7.4 pH∙min/kg) were classified as AR and AS, respectively, and used in the subsequent study. The steers were force-fed a diet containing 85% grain at 60% of the expected daily intake (5.8 ± 0.8 and 5.6 ± 0.6 kg for AR and AS, respectively) within 30 min. Mean ruminal pH over the postprandial 6-h period was higher for AR compared with AS (6.02 vs. 5.55), and mean total VFA concentration was 74% for AR compared with AS (122 vs. 164 mM). Molar proportion of butyrate in the ruminal fluid was 139% higher for AR compared with AS (17.5 vs. 7.33 mol/100 mol of VFA). Expression of monocarboxylate cotransporter isoform 1, sodium hydrogen exchanger isoforms 1 and 2, and anion exchangers (downregulated in adenoma and putative anion exchanger, isoform 1) did not differ between AR and AS steers. However, expression of sodium hydrogen exchanger isoform 3, which imports Na(+) to the epithelial cell and exports H(+) to the rumen, was 176% higher in AR steers than in AS steers. Higher ruminal pH for AR might be partly due to a faster rate of VFA absorption, lower VFA production, or both. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of wheat dried distillers' grains with solubles and cinnamaldehyde on in vitro fermentation and protein degradation using the Rusitec technique.

PubMed

Lia, Yangling; He, Maolong; Li, Chun; Forster, Robert; Beauchemin, Karen Anne; Yang, Wenzhu

2012-04-01

This study was conducted to evaluate the effect of wheat dried distillers' grains with solubles (DDGS) and cinnamaldehyde (CIN) on in vitro fermentation and microbial profiles using the rumen simulation technique. The control substrate (10% barley silage, 85% barley grain and 5% supplement, on dry matter basis) and the wheat DDGS substrate (30% wheat DDGS replaced an equal portion of barley grain) were combined with 0 and 300 mg CIN/l of culture fluid. The inclusion of DDGS increased (p < 0.05) the concentration of volatile fatty acids (VFA) and the molar proportion of acetate and propionate. Dry matter disappearance (p = 0.03) and production of bacterial protein (p < 0.01) were greater, whereas the disappearances of crude protein (CP) and neutral detergent fibre were less (p < 0.01) for the DDGS than for the control substrate. With addition of CIN, concentration of total VFA decreased and fermentation pattern changed to greater acetate and less propionate proportions (p < 0.01). The CIN reduced (p < 0.01) methane production and CP degradability. The copy numbers of Fibrobacter, Prevotella and Archaea were not affected by DDGS but were reduced (p < 0.05) by CIN. The results indicate that replacing barley grain by DDGS increased nutrient fermentability and potentially increase protein flows to the intestine. Supplementation of high-grain substrates with CIN reduced methane production and potentially increased the true protein reaching the small intestine; however, overall reduction of feed fermentation may lower the feeding value of a high-grain diet.

Comparative Demonstration of Active and Semi-Passive in Situ Bioremediation Approaches for Perchlorate-Impacted Groundwater at Longhorn Army Ammunitions Plant

DTIC Science & Technology

2009-01-01

wells in order to achieve the desired electron donor coverage. Soluble electron donors such as sodium lactate, citric acid , or ethanol have been used in...ORP) Monitoring.............39 6.7.5 Results of Volatile Fatty Acids (VFA) Analysis............................39 6.7.6 Results of Sulfate Analysis...VC vinyl chloride VFA volatile fatty acid VOC volatile organic compounds Technical material contained in this report has been approved for

Effects of Visceral Fat Accumulation Awareness on a Web-Based Weight-Loss Program: Japanese Study of Visceral Adiposity and Lifestyle Information-Utilization and Evaluation (J-VALUE).

PubMed

Sakane, Naoki; Dohi, Seitaro; Sakata, Koichi; Hagiwara, Shin-Ichi; Morimoto, Toshihisa; Uchida, Takanobu; Katashima, Mitsuhiro; Yanagisawa, Yoshiko; Yasumasu, Takeshi; Study Group, J-Value

2013-01-01

A reduction of visceral fat is important for improvement of metabolic risk. This study was designed to compare the effects of a web-based program alone or together with measurement and self-awareness of accumulated visceral fat in Japanese workers. A new noninvasive device to measure visceral fat accumulation was introduced, and efficacy on weight-loss and improvement of healthy behaviors were examined. This study was conducted according to Helsinki declaration and approved by the ethical committee of Japan Hospital Organization, National Kyoto Hospital. Two-hundred and sixteen overweight and obese males with BMI of more than 23 participated from 8 healthcare offices of 3 Japanese private companies. Subjects were randomly allocated into control group, Web-based weight-loss program (Web), or Web + Visceral fat measurement group (Web + VFA). Eighty-one percent of participants completed the study. Reductions of body weight, waist circumference, and BMI were the largest in Web + VFA group, and the differences between groups were significant by ANOVA. Improvements of healthy behaviors were the largest in Web + VFA group, and the differences of healthy eating improvement scores between Web + VFA and control groups were significant. Our findings suggest that measurement and awareness of visceral fat are effective in weight reduction in overweight and obese males in the workplace.

Investigation into the effect of high concentrations of volatile fatty acids in anaerobic digestion on methanogenic communities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franke-Whittle, Ingrid H., E-mail: ingrid.whittle@uibk.ac.at; Walter, Andreas; Ebner, Christian

Highlights: • Different methanogenic communities in mesophilic and thermophilic reactors. • High VFA levels do not cause major changes in archaeal communities. • Real-time PCR indicated greater diversity than ANAEROCHIP microarray. - Abstract: A study was conducted to determine whether differences in the levels of volatile fatty acids (VFAs) in anaerobic digester plants could result in variations in the indigenous methanogenic communities. Two digesters (one operated under mesophilic conditions, the other under thermophilic conditions) were monitored, and sampled at points where VFA levels were high, as well as when VFA levels were low. Physical and chemical parameters were measured, andmore » the methanogenic diversity was screened using the phylogenetic microarray ANAEROCHIP. In addition, real-time PCR was used to quantify the presence of the different methanogenic genera in the sludge samples. Array results indicated that the archaeal communities in the different reactors were stable, and that changes in the VFA levels of the anaerobic digesters did not greatly alter the dominating methanogenic organisms. In contrast, the two digesters were found to harbour different dominating methanogenic communities, which appeared to remain stable over time. Real-time PCR results were inline with those of microarray analysis indicating only minimal changes in methanogen numbers during periods of high VFAs, however, revealed a greater diversity in methanogens than found with the array.« less

Investigation of the impact of trace elements on anaerobic volatile fatty acid degradation using a fractional factorial experimental design.

PubMed

Jiang, Ying; Zhang, Yue; Banks, Charles; Heaven, Sonia; Longhurst, Philip

2017-11-15

The requirement of trace elements (TE) in anaerobic digestion process is widely documented. However, little is understood regarding the specific requirement of elements and their critical concentrations under different operating conditions such as substrate characterisation and temperature. In this study, a flask batch trial using fractional factorial design is conducted to investigate volatile fatty acids (VFA) anaerobic degradation rate under the influence of the individual and combined effect of six TEs (Co, Ni, Mo, Se, Fe and W). The experiment inoculated with food waste digestate, spiked with sodium acetate and sodium propionate both to 10 g/l. This is followed by the addition of a selection of the six elements in accordance with a 2 6-2 fractional factorial principle. The experiment is conducted in duplicate and the degradation of VFA is regularly monitored. Factorial effect analysis on the experimental results reveals that within these experimental conditions, Se has a key role in promoting the degradation rates of both acetic and propionic acids; Mo and Co are found to have a modest effect on increasing propionic acid degradation rate. It is also revealed that Ni shows some inhibitory effects on VFA degradation, possibly due to its toxicity. Additionally, regression coefficients for the main and second order effects are calculated to establish regression models for VFA degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Changes in in vitro gas and methane production from rumen fluid from dairy cows during adaptation to feed additives in vivo.

PubMed

Klop, G; van Laar-van Schuppen, S; Pellikaan, W F; Hendriks, W H; Bannink, A; Dijkstra, J

2017-04-01

The adaptation of dairy cows to methane (CH4)-mitigating feed additives was evaluated using the in vitro gas production (GP) technique. Nine rumen-fistulated lactating Holstein cows were grouped into three blocks and within blocks randomly assigned to one of three experimental diets: Control (CON; no feed additive), Agolin Ruminant® (AR; 0.05 g/kg dry matter (DM)) or lauric acid (LA; 30 g/kg DM). Total mixed rations composed of maize silage, grass silage and concentrate were fed in a 40 : 30 : 30 ratio on DM basis. Rumen fluid was collected from each cow at days -4, 1, 4, 8, 15 and 22 relative to the introduction of the additives in the diets. On each of these days, a 48-h GP experiment was performed in which rumen fluid from each individual donor cow was incubated with each of the three substrates that reflected the treatment diets offered to the cows. DM intake was on average 19.8, 20.1 and 16.2 kg/day with an average fat- and protein-corrected milk production of 30.7, 31.7 and 26.2 kg/day with diet CON, AR and LA, respectively. In general, feed additives in the donor cow diet had a larger effect on gas and CH4 production than the same additives in the incubation substrate. Incubation substrate affected asymptotic GP, half-time of asymptotic CH4 production, total volatile fatty acid (VFA) concentration, molar proportions of propionate and butyrate and degradation of organic matter (OMD), but did not affect CH4 production. No substrate×day interactions were observed. A significant diet×day interaction was observed for in vitro gas and CH4 production, total VFA concentration, molar proportions of VFA and OMD. From day 4 onwards, the LA diet persistently reduced gas and CH4 production, total VFA concentration, acetate molar proportion and OMD, and increased propionate molar proportion. In vitro CH4 production was reduced by the AR diet on day 8, but not on days 15 and 22. In line with these findings, the molar proportion of propionate in fermentation fluid was greater, and that of acetate smaller, for the AR diet than for the CON diet on day 8, but not on days 15 and 22. Overall, the data indicate a short-term effect of AR on CH4 production, whereas the CH4-mitigating effect of LA persisted.

Association between abdominal fat distribution and atherosclerotic changes in the carotid artery.

PubMed

Oike, Miki; Yokokawa, Hirohide; Fukuda, Hiroshi; Haniu, Tomomi; Oka, Fukuko; Hisaoka, Teruhiko; Isonuma, Hiroshi

2014-01-01

We aimed to evaluate the association between abdominal fat distribution (e.g., abdominal visceral fat area [VFA], subcutaneous fat area [SFA], and total fat area [TFA]), waist circumference (WC), or body mass index (BMI) and atherosclerotic changes in the carotid artery after adjusting for common risk factors. The present study is a hospital-based, cross-sectional study. Study participants included 223 Japanese individuals who underwent a medical health checkup at Juntendo University Hospital, Tokyo, between December 2005 and August 2011. Multivariate logistic regression analysis was used to examine the association between abdominal VFA, SFA, TFA, the VFA/SFA ratio, WC, or BMI and intima-media thickness [IMT] (mean IMT≥1.1mm or maximum IMT≥1.2mm) as atherosclerotic changes in the carotid artery. Multivariate logistic regression analysis showed that VFA (OR for ≥150cm(2) versus <100cm(2), 3.88; 95% CI, 1.39-10.85), BMI (OR for ≥27.6kg/m(2) versus <25kg/m(2), 5.22; 95% CI, 1.69-16.16), and TFA (OR for 200-285cm(2) versus <200cm(2), 4.15; 95% CI, 1.34-12.86: OR for ≥285cm(2) versus <200cm(2), 5.53; 95% CI, 1.76-17.35) were significantly associated with atherosclerotic changes in men. After adjustment for BMI, only TFA (OR for ≥285cm(2) versus <200cm(2), 3.76; 95%CI, 1.03-13.79) in men was significantly associated with atherosclerotic changes in the carotid artery. Our results indicate that VFA, TFA, and BMI are independently associated with atherosclerotic changes in Japanese men. TFA may be considered as a valuable measure of atherosclerotic changes. Copyright © 2013 Asian Oceanian Association for the Study of Obesity. Published by Elsevier Ltd. All rights reserved.

Symptoms related to glaucomatous visual field abnormalities among male Japanese workers in a population-based setting.

PubMed

Tatemichi, Masayuki; Nakano, Tadashi; Hayashi, Takeshi; Tanaka, Katsutoshi; Hiro, Hisanori; Miyamoto, Toshiaki; Aratake, Miho; Nishinoue, Norihide; Yamazaki, Akira; Nakadate, Toshio; Sugita, Minoru

2012-09-01

To identify symptoms potentially related to glaucomatous visual field abnormalities (VFAs) in a population-based setting, and to assess the applicability of using these symptoms to identify persons at risk of developing glaucoma. In this study, 10,214 Japanese male general workers (mean age, 45.3±8.8 years) filled out a self-administered questionnaire and underwent frequency doubling technology (FDT) perimetry testing. The questionnaire inquired about whether the participant was suffering from any of nine symptoms, with scores for each response graded on a four-item Likert scale: 0 (none), 1 (rarely), 2 (sometimes), and 3 (always). Results from the questionnaire were compared among three groups: participants without any VFAs (9767), participants with VFAs as determined by the FDT test (FDT-VFA; 447), and 227 participants (of the 447 FDT-VFA participants) with glaucomatous VFAs who were newly diagnosed by ophthalmologic examinations. The mean summed scores for the total items were significantly (p<0.01) higher in FDT- and glaucomatous VFA groups than in normal subjects. In particular, responses citing the symptoms 'feeling of something in the front of the eye' and 'feeling of hardness to see in dark places' were significantly (p<0.05) more frequent in subjects with FDT- and glaucomatous VFAs than among normal participants. However, the respective areas under the receiver operating characteristic curve of summed scores for the nine total items and for the two items which showed significant differences for the glaucoma groups were 0.57 (95% confidence interval=0.53-0.60) and 0.58 (95% confidence interval=0.54-0.61). Although the symptoms 'feeling of hardness to see in dark places' and 'feeling of something in the front of the eye' could be associated with glaucomatous VFA in a population-based setting, inquiring about symptoms is of little aid in identifying subjects with glaucomatous VFA as a strategy for public health. © 2010 The Authors. Journal compilation © 2010 Acta Ophthalmol.

Influence of genotype and diet on steer performance, manure odor, and carriage of pathogenic and other fecal bacteria. III. Odorous compound production.

PubMed

Miller, D N; Berry, E D; Wells, J E; Ferrell, C L; Archibeque, S L; Freetly, H C

2006-09-01

Three beef cattle diets were assessed for their potential to produce odorous compounds from cattle feces excreted during the growing and finishing periods. Eight pens containing 51 steers of varying proportions of Brahman and MARC III genotypes were fed either a chopped bromegrass hay diet or a corn silage diet for a 119-d growing period. After the growing period, all steers were switched to the same high-corn finishing diet (high corn) and fed to a target weight of 560 kg (finishing period). Fecal slurries were prepared from a composite of fresh fecal pats collected in each pen during both periods and incubated anaerobically. In additional flasks, starch, protein, or cellulose was added to the composite fecal subsamples to determine the preferred substrates for fermentation and odorous compound production. The content and composition of the fermentation products varied both initially and during the incubation, depending on the diet fed to the steers. The corn silage and high corn feces had the greater initial content of VFA (381.0 and 524.4 micromol/g of DM, respectively) compared with the bromegrass feces (139.3 micromol/g of DM) and accumulated more VFA than the bromegrass feces during the incubation. l-Lactic acid and VFA accumulation in the high corn and corn silage feces was at the expense of starch, based on starch loss and the production of straight-chain VFA. In the bromegrass feces, accumulation of branched-chain VFA and aromatic compounds and the low starch availability indicated that the protein in the feces was the primary source for odorous compound production. Substrate additions confirmed these conclusions. We conclude that starch availability was the primary factor determining accumulation and composition of malodorous fermentation products, and when starch was unavailable, fecal microorganisms utilized protein.

Effects of dietary carbohydrates on rumen epithelial metabolism of nonlactating heifers.

PubMed

Argov-Argaman, N; Eshel, O; Moallem, U; Lehrer, H; Uni, Z; Arieli, A

2012-07-01

Ruminal wall metabolism was studied in nonlactating heifers by altering the carbohydrate (CHO) digestion site between rumen and intestine. The CHO digestion site was estimated from in situ and total-tract digestibility of control (CONT) diets and diets supplemented with corn (CRN), barley (BARL), or soy hulls (SOYH). Ruminal epithelial metabolism regulating gene expression, morphology, and nutrient delivery was assessed from a combination of rumen volatile fatty acid (VFA) concentration, biopsies for papilla morphology, and expression of putative metabolic regulatory genes encoding enzymes that facilitate VFA utilization. Digestible dry matter and CHO intake were 25 and 45% higher, respectively, in the supplemented diets than in CONT diets. Fiber supplementation increased the intestinal and decreased ruminal CHO digestion. Ruminal nonfiber CHO digestibility was 10% lower in CRN than with the high rumen-degradable supplement. The CONT heifers had lowest total ruminal VFA and highest acetate concentration relative to the other treatments. Total VFA concentration in BARL and CRN diets tended to be higher than in SOYH. The SOYH diet tended to reduce papilla dimension relative to CRN and BARL. The CRN diet tended to increase papilla surface area relative to BARL and SOYH. Gene expression of propionyl-coenzyme A carboxylase was higher in CRN and BARL than in SOYH diets, and tended to be higher in CRN than in BARL and SOYH diets. Lactate dehydrogenase and butyryl coenzyme A synthase gene transcripts tended to be higher in CONT than in the supplemented treatments. Thus, rumen epithelial expression of genes involved in VFA metabolism and ruminal wall-structure development are influenced by other regulatory mechanism that is not directly affected by local signals. The in situ methods used are a useful tool for differentiating ruminal from extraruminal nutrient supply. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Dual Approach to Vibrational Spectra in Solution: Microscopic Influence of Hydrogen Bonding to the State of Motion of Glycine in Water.

PubMed

Kitamura, Yukichi; Takenaka, Norio; Koyano, Yoshiyuki; Nagaoka, Masataka

2014-08-12

We have proposed a new theoretical methodology to clarify the microscopic nature of the vibrational properties in solution, which consists of a combination of the vibrational frequency analyses (VFAs) with two kinds of Hessian matrices, that is, the effective Hessian on the free energy surface (free energy Hessian: "FE-Hessian") and the instantaneous one (instantaneous normal mode Hessian: "INM-Hessian") within QM/MM framework. In these VFAs, the Hessians were obtained by the analytical approach, having the advantages from the aspect of both the computational efficiency and accuracy in comparison to those obtained by the numerical one. In the present study, we have applied them to the glycine aqueous solution. First, by using the VFA with the FE-Hessian (VFA-FEH), we estimated the vibrational frequency shifts induced by solvent water molecules. The calculated values were quantitatively in agreement with experimental ones. It was clearly demonstrated that such vibrational shifts are attributed to not only the structural relaxation but also the explicit solute-solvent interactions (i.e., interatomic interactions). Second, by using the VFA with the INM-Hessian (VFA-INMH), the vibrational spectra in solution were investigated through the vibrational INM densities of states (DOS). By the comparison between the spectroscopic features and the microscopic solvation structure around glycine molecule, it was found that the frequency shifts and bandwidths in IR spectra are closely correlated with the hydrogen bonding (HB) network formations. In particular, the instantaneous changes of vibrational states of the hydroxyl group and carbonyl one, showing apparently inverse tendency on the strength of the HB interaction, can be explained very well on the basis of two different mechanisms, that is, the direct change of electron density in the bonding orbitals and the indirect one due to hyperconjugation between the lone electron pair and the antibonding orbitals, respectively. In conclusion, the present dual VFA approach is a quite useful strategy to interpret the microscopic origin of the experimental vibrational spectra.

Prevention of volatile fatty acids production and limitation of odours from winery wastewaters by denitrification.

PubMed

Bories, André; Guillot, Jean-Michel; Sire, Yannick; Couderc, Marie; Lemaire, Sophie-Andréa; Kreim, Virginie; Roux, Jean-Claude

2007-07-01

The effect of the addition of nitrate to winery wastewaters to control the formation of VFA in order to prevent odours during storage and treatment was studied in batch bioreactors at different NO(3)/chemical oxygen demand (COD) ratios and at full scale in natural evaporation ponds (2 x 7000 m(2)) by measuring olfactory intensity. In the absence of nitrate, butyric acid (2304 mgL(-1)), acetic acid (1633 mgL(-1)), propionic acid (1558 mgL(-1)), caproic acid (499 mgL(-1)) and valeric acid (298 mgL(-1)) were produced from reconstituted winery wastewater. For a ratio of NO(3)/COD=0.4 gg(-1), caproic and valeric acids were not formed. The production of butyric and propionic acids was reduced by 93.3% and 72.5%, respectively, at a ratio of NO(3)/COD=0.8, and by 97.4% and 100% at a ratio of NO(3)/COD=1.2 gg(-1). Nitrate delayed and decreased butyric acid formation in relation to the oxidoreduction potential. Studies in ponds showed that the addition of concentrated calcium nitrate (NITCAL) to winery wastewaters (3526 m(3)) in a ratio of NO(3)/COD=0.8 inhibited VFA production, with COD elimination (94%) and total nitrate degradation, and no final nitrite accumulation. On the contrary, in ponds not treated with nitrate, malodorous VFA (from propionic to heptanoïc acids) represented up to 60% of the COD. Olfactory intensity measurements in relation to the butanol scale of VFA solutions and the ponds revealed the pervasive role of VFA in the odour of the untreated pond as well as the clear decrease in the intensity and not unpleasant odour of the winery wastewater pond enriched in nitrates. The results obtained at full scale underscored the feasibility and safety of the calcium nitrate treatment as opposed to concentrated nitric acid.

Postprandial portal fluxes of essential amino acids, volatile fatty acids, and urea-nitrogen in growing pigs fed a high-fiber diet supplemented with a multi-enzyme cocktail.

PubMed

Agyekum, A K; Kiarie, E; Walsh, M C; Nyachoti, C M

2016-09-01

The present study investigated the effects of adding a multi-enzyme cocktail (MC) to a high-fiber diet on net portal-drained viscera (PDV) fluxes of essential AA (EAA), volatile fatty acids (VFA), and blood urea-N (BUN) in growing pigs. Five female pigs (22.8 ± 1.6 kg BW), with catheters in the portal vein, ileal vein, and carotid artery, were fed 3 isocaloric-nitrogenous diets at 4% of their BW once daily at 0900 h for 7 d in a replicated 3 × 3 Latin square design. The diets contained corn and soybean meal with 0% (control) or 30% distillers' dried grains with solubles (DDGS; HF) produced from a 1:1 mixture of wheat and corn. The third diet was supplemented with MC in addition to the 30% DDGS (HF + MC). The MC supplied (analyzed values) 5,397 U of xylanase, 162 U of β-glucanase, and 2,000 U of protease and guaranteed minimum activities of 1,000 U of α-amylase and 25 U of pectinase per kg of diet. On d 7, para-amino hippuric acid was infused into the ileal vein (to measure flow rate), and blood was sampled from the portal vein and carotid artery for 7 h after feeding to assay EAA, urea-N, and VFA. Portal absorption of nutrients was derived by multiplying the porto-arterial plasma concentration differences by portal vein blood flow. Diet had no effect on postprandial portal vein plasma flow rate and net BUN flux, but portal BUN tended to be lower ( = 0.070) and arterial BUN was lower ( 0.05) over the 7 h in pigs fed control. Postprandial portal Arg, Ile, Leu, Trp, and Val or net fluxes were lower ( 0.05) in HF-fed pigs from 30 to 240 min than control-fed pigs and MC supplementation tended (0.05 ≤ ≤ 0.10) to or improved ( 0.05) portal appearances of those AA, but not their fluxes. Control-fed pigs had higher ( 0.05) net portal fluxes of most EAA and pigs fed HF + MC had higher ( 0.05) Lys, and similar Met and Phe net portal fluxes were compared with control-fed pigs. Portal VFA was not affected by diet. However, total portal VFA flux was lower ( 0.05) in the HF-fed pigs than in the control pigs. The MC supplementation improved the total portal VFA flux, although it did not improve arterial VFA concentration relative to the HF diet. In conclusion, supplementing the HF diet with MC improved net portal appearance of some EAA and fluxes of total VFA, whereas fluxes of EAA did not change. The HF diet increased EAA demand by the PDV, but MC addition was not able to reduce this demand.

Effects of gas composition in headspace and bicarbonate concentrations in media on gas and methane production, degradability, and rumen fermentation using in vitro gas production techniques.

PubMed

Patra, Amlan Kumar; Yu, Zhongtang

2013-07-01

Headspace gas composition and bicarbonate concentrations in media can affect methane production and other characteristics of rumen fermentation in in vitro gas production systems, but these 2 important factors have not been evaluated systematically. In this study, these 2 factors were investigated with respect to gas and methane production, in vitro digestibility of feed substrate, and volatile fatty acid (VFA) profile using in vitro gas production techniques. Three headspace gas compositions (N2+ CO2+ H2 in the ratio of 90:5:5, CO2, and N2) with 2 substrate types (alfalfa hay only, and alfalfa hay and a concentrate mixture in a 50:50 ratio) in a 3×2 factorial design (experiment 1) and 3 headspace compositions (N2, N2 + CO2 in a 50:50 ratio, and CO2) with 3 bicarbonate concentrations (80, 100, and 120 mM) in a 3×3 factorial design (experiment 2) were evaluated. In experiment 1, total gas production (TGP) and net gas production (NGP) was the lowest for CO2, followed by N2, and then the gas mixture. Methane concentration in headspace gas after fermentation was greater for CO2 than for N2 and the gas mixture, whereas total methane production (TMP) and net methane production (NMP) were the greatest for CO2, followed by the gas mixture, and then N2. Headspace composition did not affect in vitro digestibility or the VFA profile, except molar percentages of propionate, which were greater for CO2 and N2 than for the gas mixture. Methane concentration in headspace gas, TGP, and NGP were affected by the interaction of headspace gas composition and substrate type. In experiment 2, increasing concentrations of CO2 in the headspace decreased TGP and NGP quadratically, but increased the concentrations of methane, NMP, and in vitro fiber digestibility linearly, and TMP quadratically. Fiber digestibility, TGP, and NGP increased linearly with increasing bicarbonate concentrations in the medium. Concentrations of methane and NMP were unaffected by bicarbonate concentration, but TMP tended to increase due to increasing bicarbonate concentration. Although total VFA concentration and molar percentage of butyrate were unchanged, the molar percentage of acetate, and acetate-to-propionate ratio decreased, whereas the molar percentage of propionate increased quadratically with increasing bicarbonate concentration. This study demonstrated for the first time that headspace composition, especially CO2 content, and bicarbonate concentration in media could significantly influence gas and methane production, and rumen fermentation in gas production techniques. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Improved volatile fatty acid and biomethane production from lipid removed microalgal residue (LRμAR) through pretreatment.

PubMed

Suresh, Arumuganainar; Seo, Charles; Chang, Ho Nam; Kim, Yeu-Chun

2013-12-01

Renewable energy from lipid removed microalgal residues (LRμARs) serves as a promising tool for sustainable development of the microalgal biodiesel industry. Hence, in this study, LRμAR from Ettlia sp. was characterized for its physico-biochemical parameters, and applied to various pretreatment to increase the biodegradability and used in batch experiments for the production of volatile fatty acids (VFA) and biomethane. After various pretreatments, the soluble organic matters were increased at a maximum of 82% in total organic matters in alkali-autoclaved sample. In addition, VFA and methane production was enhanced by 30% and 40% in alkali-sonicated and alkali-autoclaved samples, respectively. Methane heating value was recovered at maximum of 6.6 MJ kg(-1)VS in alkali-autoclaved conditions with comparison to non-pretreated samples. The pretreatment remarkably improved LRμAR solubilization and enhanced VFA and biomethane production, which holds immense potential to eventually reduce the cost of algal biodiesel. Copyright © 2013 Elsevier Ltd. All rights reserved.

Acidogenic fermentation characteristics of different types of protein-rich substrates in food waste to produce volatile fatty acids.

PubMed

Shen, Dongsheng; Yin, Jun; Yu, Xiaoqin; Wang, Meizhen; Long, Yuyang; Shentu, Jiali; Chen, Ting

2017-03-01

In this study, tofu and egg white, representing typical protein-rich substrates in food waste based on vegetable and animal protein, respectively, were investigated for producing volatile fatty acids (VFAs) by acidogenic fermentation. VFA production, composition, conversion pathways and microbial communities in acidogenesis from tofu and egg white with and without hydrothermal (HT) pretreatment were compared. The results showed HT pretreatment could improve the VFA production of tofu but not for egg white. The optimum VFA yields were 0.46g/gVS (tofu with HT) and 0.26g/gVS (egg white without HT), respectively. Tofu could directly produce VFAs through the Stickland reaction, while egg white was converted to lactate and VFAs simultaneously. About 30-40% of total protein remained in all groups after fermentation. Up to 50% of the unconverted soluble protein in the HT groups was protease. More lactate-producing bacteria, mainly Leuconostoc and Lactobacillus, were present during egg white fermentation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improving production of volatile fatty acids from food waste fermentation by hydrothermal pretreatment.

PubMed

Yin, Jun; Wang, Kun; Yang, Yuqiang; Shen, Dongsheng; Wang, Meizhen; Mo, Han

2014-11-01

Food waste (FW) was pretreated by a hydrothermal method and then fermented for volatile fatty acid (VFAs) production. The soluble substance in FW increased after hydrothermal pretreatment (⩽200 °C). Higher hydrothermal temperature would lead to mineralization of the organic compounds. The optimal temperature for organic dissolution was 180 °C, at which FW dissolved 42.5% more soluble chemical oxygen demand than the control. VFA production from pretreated FW fermentation was significantly enhanced compared with the control. The optimal hydrothermal temperature was 160 °C with a VFA yield of 0.908 g/g VSremoval. Butyrate and acetate were the prevalent VFAs followed by propionate and valerate. FW fermentation was inhibited after 200 °C pretreatment. The VFAs were extracted from the fermentation broth by liquid-liquid extraction. The VFA recovery was 50-70%. Thus, 0.294-0.411 g VFAs could be obtained per gram of hydrothermally pretreated FW (in dry weight) by this method. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Agitation on Acidogenesis Stage of Two-Stage Anaerobic Digestion of Palm Oil Mill Effluent (POME) into Biogas

NASA Astrophysics Data System (ADS)

Trisakti, B.; Irvan; Adipasah, H.; Taslim; Turmuzi, M.

2017-03-01

The acidogenesis stage in two-stage anaerobic digestion of palm oil mill effluent (POME) was studied in a continuous stirred tank reactor (CSTR). This research investigated the effect of agitation rate on the growth of microorganisms, the degradation of organic substances, and volatile fatty acids (VFA) production and composition. Initially, the suitable loading up was determined by varying the HRT 6.7, 5.0, and 4.0 days in a 2 L CSTR with agitation rate 50 rpm, pH 6.0 ± 0.2, at room temperature. Next, effect of agitation on the process was determined by varying agitation rate at 25, 50, 100, and 200 rpm. Analysis of total solids (TS), volatile solids (VS), total suspended solids (TSS), volatile suspended solids (VSS), chemical oxygen demand (COD), and volatile fatty acids (VFA) were conducted in order to study the growth of microorganisms and their abilities in converting organic compound to produce VFA. The highest growth of microorganisms was achieved at HRT 4.0 day with microorganism concentration was 20.62 mg VSS/L and COD reduction was 15.7%. The highest production of total VFA achieved was 5,766.61 mg/L mg/L at agitation rate 200 rpm, with concentration of acetic acid, propionic acid and butyric acid were 1,889.23; 1,161.43; and 2,725.95 mg/L, respectively. While degradation VS and COD were 16.61 and 38.79%.

Synergism and effect of high initial volatile fatty acid concentrations during food waste and pig manure anaerobic co-digestion.

PubMed

Dennehy, Conor; Lawlor, Peadar G; Croize, Thomas; Jiang, Yan; Morrison, Liam; Gardiner, Gillian E; Zhan, Xinmin

2016-10-01

Anaerobic co-digestion of food waste (FW) and pig manure (PM) was undertaken in batch mode at 37°C in order to identify and quantify the synergistic effects of co-digestion on the specific methane yield (SMY) and reaction kinetics. The effects of the high initial volatile fatty acid (VFA) concentrations in PM on synergy observed during co-digestion, and on kinetic modelling were investigated. PM to FW mixing ratios of 1/0, 4/1, 3/2, 2/3, 1/4 and 0/1 (VS basis) were examined. No VFA or ammonia inhibition was observed. The highest SMY of 521±29ml CH4/gVS was achieved at a PM/FW mixing ratio of 1/4. Synergy in terms of both reaction kinetics and SMY occurred at PM/FW mixing ratios of 3/2, 2/3 and 1/4. Initial VFA concentrations did not explain the synergy observed. Throughout the study the conversion of butyric acid was inhibited. Due to the high initial VFA content of PM, conventional first order and Gompertz models were inappropriate for determining reaction kinetics. A dual pooled first order model was found to provide the best fit for the data generated in this study. The optimal mixing ratio in terms of both reaction kinetics and SMY was found at a PM/FW mixing ratio of 1/4. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessment of the effect of condensed (acacia and quebracho) and hydrolysable (chestnut and valonea) tannins on rumen fermentation and methane production in vitro.

PubMed

Hassanat, Fadi; Benchaar, Chaouki

2013-01-01

Tannins added to animal diets may have a positive effect on energy and protein utilisation in the rumen. The objective of this study was to examine the impact of different sources and concentrations (20, 50, 100, 150 and 200 g kg⁻¹ dry matter (DM)) of condensed (acacia and quebracho) and hydrolysable (chestnut and valonea) tannins on rumen microbial fermentation in vitro. The experiment also included a negative control with no tannins (control) and a positive control with monensin (10 mg L⁻¹). In vitro gas production and total volatile fatty acid (VFA) concentration decreased as tannin concentration increased. Addition of acacia, chestnut or valonea tannins at ≥ 50 g kg⁻¹ or quebracho tannins at ≥ 100 g kg⁻¹ resulted in a decrease (up to 40%) in methane (CH₄) production compared with the control. Valonea tannins were the only tannin source that reduced (-11%) CH₄ production at 50 g kg⁻¹ without affecting VFA concentration. Tannin treatments reduced ammonia (NH₃) and branched-chain VFA concentrations, indicating a reduction in ruminal protein degradation. Monensin reduced CH₄ production (-37%) and NH₃ concentration (-20%) without affecting total VFA concentration. Supplying acacia, chestnut or valonea tannins at 50 g kg⁻¹ has the potential to reduce CH₄ production and ruminal protein degradation with minimum detrimental effects on efficiency of ruminal fermentation. Copyright © 2012 Crown in the right of Canada. Published by John Wiley & Sons, Ltd.

Anaerobic acidogenic digestion of olive mill wastewaters in biofilm reactors packed with ceramic filters or granular activated carbon.

PubMed

Bertin, Lorenzo; Lampis, Silvia; Todaro, Daniela; Scoma, Alberto; Vallini, Giovanni; Marchetti, Leonardo; Majone, Mauro; Fava, Fabio

2010-08-01

Four identically configured anaerobic packed bed biofilm reactors were developed and employed in the continuous acidogenic digestion of olive mill wastewaters to produce volatile fatty acids (VFAs), which can be exploited in the biotechnological production of polyhydroxyalkanoates. Ceramic porous cubes or granular activated carbon were used as biofilm supports. Aside packing material, the role of temperature and organic loading rate (OLR) on VFA production yield and mixture composition were also studied. The process was monitored through a chemical, microbiological and molecular biology integrated procedure. The highest wastewater acidification yield was achieved with the ceramic-based technology at 25 degrees C, with an inlet COD and an OLR of about 17 g/L and 13 g/L/day, respectively. Under these conditions, about the 66% of the influent COD (not including its VFA content) was converted into VFAs, whose final amount represented more than 82% of the influent COD. In particular, acetic, propionic and butyric acids were the main VFAs by composing the 55.7, 21.5 and 14.4%, respectively, of the whole VFA mixture. Importantly, the relative concentrations of acetate and propionate were affected by the OLR parameter. The nature of the packing material remarkable influenced the process performances, by greatly affecting the biofilm bacterial community structure. In particular, ceramic cubes favoured the immobilization of Firmicutes of the genera Bacillus, Paenibacillus and Clostridium, which were probably involved in the VFA producing process. (c) 2010 Elsevier Ltd. All rights reserved.

An assessment of the feasibility of employing biochemical acidogenic potential tests for characterizing anaerobic biodegradability of raw and pretreated waste activated sludge.

PubMed

Kianmehr, Peiman; Parker, Wayne; Seto, Peter

2012-04-01

The potential to use the results of biochemical acid potential (BAP) tests to predict the ultimate digestibility of raw and pretreated waste activated sludge (WAS) was investigated. The ultimate methane production from biochemical methane potential (BMP) tests on raw and pretreated samples which spanned a range of biodegradability proved linearly related to the volatile fatty acid (VFA) and soluble chemical oxygen demand (COD) production in corresponding BAP tests. In addition, a linear relationship between NH4-N production in the BMP and BAP tests was observed. Despite the linear nature of the relationships, the ratio of the production of methane in the BMP tests to the production of VFAs in the BAP tests varied with the biodegradability of the sludge samples. Waste Activated Sludge samples with low digestibility had ultimate yields of CH4 that were greater than the VFA yields in BAP tests, whereas sludge samples with high digestibility had lower yields of CH4 than the corresponding VFA yields. This trend contrasted with the NH4 results, in which the yields in the BAP tests were consistently less than those observed in the BMP tests. It was hypothesized that the varying relationship between CH4 and VFA yields was because of the inhibition of anaerobic oxidation of long-chain fatty acids (LCFAs) in the BAP tests. Long-chain fatty acids would be converted to CH4 in BMP tests but produced as digestion intermediates in the BAP tests and were not measured as part of the VFA yield. Hydrogen and acetate were identified as the two most likely intermediates that would accumulate in the BAP tests (which would cause inhibition). A stoichiometric model to facilitate the development of an improved understanding of the biodegradation processes in the BAP and BMP tests was assembled. When the model was applied to the BAP tests the anaerobic oxidation of LCFAs and propionate and methanogenesis were excluded from the model. The model was employed to estimate the extent of degradation of lipids, carbohydrates, and proteins in the batch tests as a function of the ultimate biodegradability of the sludge samples. On the basis of model fitting, it was determined that the degradation of lipids in BMP tests decreased, whereas the degradation of carbohydrates and proteins increased as the digestibility of the sludge samples increased. The varying ratio of lipid to protein and carbohydrate degradability with increasing digestibility of the sludge samples describes the relationship between VFA production and CH4 production in the BAP, and BMP tests, respectively.

Improved biogas production from rice straw by co-digestion with kitchen waste and pig manure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Jingqing; School of Environmental Sciences and Engineering, Sun Yat-sen University, Guangzhou 510275; Li, Dong

Highlights: • Biogas production was enhanced by co-digestion of rice straw with other materials. • The optimal ratio of kitchen waste, pig manure and rice straw is 0.4:1.6:1. • The maximum biogas yield of 674.4 L/kg VS was obtained. • VFA inhibition occurred when kitchen waste content was more than 26%. • The dominant VFA were propionate and acetate in successful reactors. - Abstract: In order to investigate the effect of feedstock ratios in biogas production, anaerobic co-digestions of rice straw with kitchen waste and pig manure were carried out. A series of single-stage batch mesophilic (37 ± 1 °C)more » anaerobic digestions were performed at a substrate concentration of 54 g/L based on volatile solids (VS). The results showed that the optimal ratio of kitchen waste, pig manure, and rice straw was 0.4:1.6:1, for which the C/N ratio was 21.7. The methane content was 45.9–70.0% and rate of VS reduction was 55.8%. The biogas yield of 674.4 L/kg VS was higher than that of the digestion of rice straw or pig manure alone by 71.67% and 10.41%, respectively. Inhibition of biogas production by volatile fatty acids (VFA) occurred when the addition of kitchen waste was greater than 26%. The VFA analysis showed that, in the reactors that successfully produced biogas, the dominant intermediate metabolites were propionate and acetate, while they were lactic acid, acetate, and propionate in the others.« less

Effect of the Organic Loading Rate Increase and the Presence of Zeolite on Microbial Community Composition and Process Stability During Anaerobic Digestion of Chicken Wastes.

PubMed

Ziganshina, Elvira E; Belostotskiy, Dmitry E; Ilinskaya, Olga N; Boulygina, Eugenia A; Grigoryeva, Tatiana V; Ziganshin, Ayrat M

2015-11-01

This study investigates the effect of the organic loading rate (OLR) increase from 1.0 to 3.5 g VS L(-1) day(-1) at constant hydraulic retention time (HRT) of 35 days on anaerobic reactors' performance and microbial diversity during mesophilic anaerobic digestion of ammonium-rich chicken wastes in the absence/presence of zeolite. The effects of anaerobic process parameters on microbial community structure and dynamics were evaluated using a 16S ribosomal RNA gene-based pyrosequencing approach. Maximum 12 % of the total ammonia nitrogen (TAN) was efficiently removed by zeolite in the fixed zeolite reactor (day 87). In addition, volatile fatty acids (VFA) in the fixed zeolite reactor accumulated in lower concentrations at high OLR of 3.2-3.5 g VS L(-1) day(-1). Microbial communities in the fixed zeolite reactor and reactor without zeolite were dominated by various members of Bacteroidales and Methanobacterium sp. at moderate TAN and VFA levels. The increase of the OLR accompanied by TAN and VFA accumulation and increase in pH led to the predominance of representatives of the family Erysipelotrichaceae and genera Clostridium and Methanosarcina. Methanosarcina sp. reached relative abundances of 94 and 57 % in the fixed zeolite reactor and reactor without zeolite at the end of the experimental period, respectively. In addition, the diminution of Synergistaceae and Crenarchaeota and increase in the abundance of Acholeplasmataceae in parallel with the increase of TAN, VFA, and pH values were observed.

Reducing methane production by supplementation of Terminalia chebula RETZ. containing tannins and saponins.

PubMed

Anantasook, Nirawan; Wanapat, Metha; Gunun, Pongsatorn; Cherdthong, Anusorn

2016-06-01

This study investigates the effects of Terminalia chebula Retz. meal supplementation on rumen fermentation and methane (CH4 ) production by using an in vitro gas technique. The experimental design was a completely randomized design (CRD) and the dietary treatments were T. chebula supplementation at 0, 4, 8, 12, 16 and 20 mg with 0.5 g of roughage and concentrate ratio at 60:40. The results revealed that cumulative gas production (96 h of incubation) were higher (P < 0.01) with T. chebula supplementation at 12, 16 and 20 mg than other treatments. However, in vitro dry matter degradability (IVDMD) and in vitro organic matter digestibility (IVOMD) were not significantly different among treatments (P > 0.05). The NH3 -N concentrations tended to quadratically increase with increasing levels of T. chebula in the diet. In addition, total volatile fatty acids (VFA) and propionate concentrations were increased (P < 0.01), while acetate concentration, acetate-to-propionate ratio, CH4 production and protozoal populations were decreased (P < 0.01) when supplemented with T. chebula at 8, 12 and 16 mg, respectively. Based on this study, it could be concluded that supplementation of T. chebula at 12 mg could improve rumen fermentation by reducing CH4 production and protozoa populations, thus improving in vitro gas production and VFA profiles. © 2015 Japanese Society of Animal Science.

Effects of inclusion levels of banana (Musa spp.) peelings on feed degradability and rumen environment of cattle fed basal elephant grass.

PubMed

Nambi-Kasozi, Justine; Sabiiti, Elly Nyambobo; Bareeba, Felix Budara; Sporndly, Eva; Kabi, Fred

2016-04-01

The effect of feeding varying banana peeling (BP) levels on rumen environment and feed degradation characteristics was evaluated using three rumen fistulated steers in four treatments. The steers were fed BP at 0, 20, 40, and 60% levels of the daily ration with basal elephant grass (EG) to constitute four diets. Maize bran, cotton seed cake, and Gliricidia sepium were offered to make the diets iso-nitrogenous. The nylon bag technique was used to measure BP and EG dry matter (DM), crude protein (CP), and neutral detergent fiber (NDF) degradabilities at 0, 6, 12, 24, 48, 72, 96, and 120 h. Rumen fluid samples were collected to determine pH and volatile fatty acid (VFA) concentrations. Effective DM, CP, and NDF degradabilities of BP ranged between 574 and 807, 629-802, and 527-689 g/kg, respectively, being lower at higher BP levels. Elephant grass degradability behaved similarly with relatively high effective CP degradability (548-569 g/kg) but low effective DM and NDF degradability (381-403 and 336-373 g/kg, respectively). Rumen pH and VFA reduced with increasing BP in the diets. Rumen pH dropped to 5.8 and 5.9 at the 40 and 60% BP feeding levels, respectively. Banana peelings were better degraded than EG but higher BP levels negatively affected feed degradability and rumen environment.

Enhancing sludge biodegradability and volatile fatty acid production by tetrakis hydroxymethyl phosphonium sulfate pretreatment.

PubMed

Wu, Qing-Lian; Guo, Wan-Qian; Bao, Xian; Yin, Ren-Li; Feng, Xiao-Chi; Zheng, He-Shan; Luo, Hai-Chao; Ren, Nan-Qi

2017-09-01

A new pretreatment method based on tetrakis hydroxymethyl phosphonium sulfate (THPS) biocide was tried to enhance sludge disintegration, and improved sludge biodegradability and subsequent volatile fatty acid (VFA) production. Sludge activity decreased to less than 10% after 2 days pretreatment using 20mg/g-TSS THPS, which also obviously destroyed EPS and cell membrane, and dissolved more biodegradable substances (48.8%) than raw sludge (19.7%). Moreover, 20mg/g-TSS THPS pretreatment shortened fermentation time to 4days and improved VFA production to 2778mg COD/L (4.35 times than that in control). Therein, the sum of n-butyric, n-valeric and iso-valeric acids unexpectedly accounted for 60.5% of total VFA (only 20.1% of that in control). The more high molecular weight VFAs (C4-C5) than low molecular VFAs (C2-C3) resulted from THPS pretreatment benefited to subsequent medium-chain volatile acids (C6-C12) generation to realize the separation and recovery of organic carbon more efficiently. Copyright © 2017. Published by Elsevier Ltd.

Effect of biochar addition on hydrogen and methane production in two-phase anaerobic digestion of aqueous carbohydrates food waste.

PubMed

Sunyoto, Nimas M S; Zhu, Mingming; Zhang, Zhezi; Zhang, Dongke

2016-11-01

Effect of biochar addition on hydrogen and methane production in two-phase anaerobic digestion of aqueous carbohydrates was studied using bench-scale bioreactors. The cultures with biochar additions were placed in 100ml reactors and incubated at 35°C and pH 5 for hydrogen production. The residual cultures were then used for methane production, incubated at 35°C and pH 7. Daily yields of hydrogen and methane and weekly yield of volatile fatty acids (VFA) were measured. The hydrogen and methane production potentials, rate and lag phases of the two phases were analysed using the Gompertz model. The results showed that biochar addition increased the maximum production rates of hydrogen by 32.5% and methane 41.6%, improved hydrogen yield by 31.0% and methane 10.0%, and shortened the lag phases in the two phases by 36.0% and 41.0%, respectively. Biochar addition also enhanced VFA generation during hydrogen production and VFA degradation in methane production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of saponification on the anaerobic digestion of solid fatty residues.

PubMed

Mouneimne, A H; Carrère, H; Bernet, N; Delgenès, J P

2003-10-01

In France, fatty residues considered as "non-ultimate" waste will not be accepted in landfill from 2002, in accordance with French legislation. Anaerobic digestion appears as an alternative process to mobilize and profitably use such fermentable waste. In this work, the effect of an alkaline pretreatment on the degradation of hexane extractible matter (HEM) and the production of volatile fatty acids (VFAs) was compared in reactors working at pH 6.5 and 8.5. The results obtained showed that 40% (+/- 0.1) of HEM were degraded at pH 8.5 versus 10% (+/- 0.3) at pH 6.5, regardless of the alkali agent used to saponify the greasy wastes. The highest performances of VFA production (8.45% +/- 0.3) were obtained at pH 8.5 with greases saponified by potassium hydroxide, compared to results (4.25% +/- 0.1) with greasy waste saponified by sodium hydroxide. This difference in VFA production might be attributable to biotoxic molecules generated during the saponification of greases by soda, limiting consequently the VFA production process.

Semi-aerobic fermentation as a novel pre-treatment to obtain VFA and increase methane yield from primary sludge.

PubMed

Peces, M; Astals, S; Clarke, W P; Jensen, P D

2016-01-01

There is a growing trend to consider organic wastes as potential sources of renewable energy and value-add products. Fermentation products have emerged as attractive value-add option due to relative easy production and broad application range. However, pre-fermentation and extraction of soluble products may impact down-stream treatment processes, particularly energy recovery by anaerobic digestion. This paper investigates primary sludge pre-fermentation at different temperatures (20, 37, 55, and 70°C), treatment times (12, 24, 48, and 72h), and oxygen availability (semi-aerobic, anaerobic); and its impact on anaerobic digestion. Pre-fermentation at 20 and 37°C succeeded for VFA production with acetate and propionate being major products. Pre-fermentation at 37, 55, and 70°C resulted in higher solubilisation yield but it reduced sludge methane potential by 20%. Under semi-aerobic conditions, pre-fermentation allowed both VFA recovery (43gCODVFAkg(-1)VS) and improved methane potential. The latter phenomenon was linked to fungi that colonised the sludge top layer during pre-fermentation. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effect of pH on solubilization of organic matter and microbial community structures in sludge fermentation.

PubMed

Maspolim, Yogananda; Zhou, Yan; Guo, Chenghong; Xiao, Keke; Ng, Wun Jern

2015-08-01

Sludge fermentation between pH 4 and 11 was investigated to generate volatile fatty acids (VFA). Despite the highest sludge solubilization of 25.9% at pH 11, VFA accumulation was optimized at pH 8 (12.5% out of 13.1% sludge solubilization). 454 pyrosequencing identified wide diversity of acidogens in bioreactors operated at the various pHs, with Tissierella, Petrimonas, Proteiniphilum, Levilinea, Proteiniborus and Sedimentibacter enriched and contributing to the enhanced fermentation at pH 8. Hydrolytic enzymatic assays determined abiotic effect to be the leading cause for improved solubilization under high alkaline condition but the environmental stress at pH 9 and above might lead to disrupt biological activities and eventually VFA production. Furthermore, molecular weight (MW) characterization of the soluble fractions found large MW aromatic substances at pH 9 and above, that is normally associated with poor biodegradability, making them disadvantageous for subsequent bioprocesses. The findings provided information to better understand and control sludge fermentation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Acidogenic fermentation of food waste for volatile fatty acid production with co-generation of biohydrogen.

PubMed

Dahiya, Shikha; Sarkar, Omprakash; Swamy, Y V; Venkata Mohan, S

2015-04-01

Fermentation experiments were designed to elucidate the functional role of the redox microenvironment on volatile fatty acid (VFA, short chain carboxylic acid) production and co-generation of biohydrogen (H2). Higher VFA productivity was observed at pH 10 operation (6.3g/l) followed by pH 9, pH 6, pH 5, pH 7, pH 8 and pH 11 (3.5 g/l). High degree of acidification, good system buffering capacity along with co-generation of higher H2 production from food waste was also noticed at alkaline condition. Experiments illustrated the role of initial pH on carboxylic acids synthesis. Alkaline redox conditions assist solubilization of carbohydrates, protein and fats and also suppress the growth of methanogens. Among the carboxylic acids, acetate fraction was higher at alkaline condition than corresponding neutral or acidic operations. Integrated process of VFA production from waste with co-generation of H2 can be considered as a green and sustainable platform for value-addition. Copyright © 2015 Elsevier Ltd. All rights reserved.

Early warning indicators for process failure due to organic overloading by rapeseed oil in one-stage continuously stirred tank reactor, sewage sludge and waste digesters.

PubMed

Kleyböcker, A; Liebrich, M; Verstraete, W; Kraume, M; Würdemann, H

2012-11-01

Early warning indicators for process failures were investigated to develop a reliable method to increase the production efficiency of biogas plants. Organic overloads by the excessive addition of rapeseed oil were used to provoke the decrease in the gas production rate. Besides typical monitoring parameters, as pH, methane and hydrogen contents, biogas production rate and concentrations of fatty acids; carbon dioxide content, concentrations of calcium and phosphate were monitored. The concentration ratio of volatile fatty acids to calcium acted as an early warning indicator (EWI-VFA/Ca). The EWI-VFA/Ca always clearly and reliably indicated a process imbalance by exhibiting a 2- to 3-fold increase 3-7days before the process failure occurred. At this time, it was still possible to take countermeasures successfully. Furthermore, increases in phosphate concentration and in the concentration ratio of phosphate to calcium also indicated a process failure, in some cases, even earlier than the EWI-VFA/Ca. Copyright © 2012 Elsevier Ltd. All rights reserved.

Dietary marker effects on fecal microbial ecology, fecal VFA, nutrient digestibility coefficients, and growth performance in finishing pigs.

PubMed

Kerr, B J; Weber, T E; Ziemer, C J

2015-05-01

Use of indigestible markers such as Cr2O3, Fe2O3, and TiO2 are commonly used in animal studies to evaluate digesta rate of passage and nutrient digestibility. Yet, the potential impact of indigestible markers on fecal microbial ecology and subsequent VFA generation is not known. Two experiments utilizing a total of 72 individually fed finishing pigs were conducted to describe the impact of dietary markers on fecal microbial ecology, fecal ammonia and VFA concentrations, nutrient digestibility, and pig performance. All pigs were fed a common diet with no marker or with 0.5% Cr2O3, Fe2O3, or TiO2. In Exp. 1, after 33 d of feeding, fresh fecal samples were collected for evaluation of microbial ecology, fecal ammonia and VFA concentrations, and nutrient digestibility, along with measures of animal performance. No differences were noted in total microbes or bacterial counts in pig feces obtained from pigs fed the different dietary markers while Archaea counts were decreased (P = 0.07) in feces obtained from pigs fed the diet containing Fe2O 3compared to pigs fed the control diet. Feeding Cr2O3, Fe2O3, or TiO2 increased fecal bacterial richness (P = 0.03, 0.01, and 0.10; respectively) when compared to pigs fed diets containing no marker, but no dietary marker effects were noted on fecal microbial evenness or the Shannon-Wiener index. Analysis of denaturing gradient gel electrophoresis gels did not reveal band pattern alterations due to inclusion of dietary markers in pig diets. There was no effect of dietary marker on fecal DM, ammonia, or VFA concentrations. Pigs fed diets containing Cr2O3 had greater Ca, Cu, Fe, and P (P ≤ 0.02), but lower Ti ( P= 0.08) digestibility compared to pigs fed the control diet. Pigs fed diets containing Fe2O3 had greater Ca (P = 0.08) but lower Ti (P = 0.01) digestibility compared to pigs fed the control diet. Pigs fed diets containing TiO2 had greater Fe and Zn (P ≤ 0.09), but lower Ti ( P= 0.01) digestibility compared to pigs fed the control diet. In Exp. 2, no effect of dietary marker on pig performance was noted. Overall, the data indicate that the inclusion of Cr2O3, Fe2O3, or TiO2 as digestibility markers have little to no impact on microbial ecology, fecal ammonia or VFA concentrations, nutrient digestibility, or pig growth performance indicating they are suitable for use in digestion studies.

In vitro digestion and fermentation characteristics of canola co-products simulate their digestion in the pig intestine.

PubMed

Woyengo, T A; Jha, R; Beltranena, E; Zijlstra, R T

2016-06-01

Canola co-products are sources of amino acid and energy in pig feeds, but their fermentation characteristics in the pig intestine are unknown. Thus, we determined the in vitro fermentation characteristics of the canola co-products Brassica juncea solvent-extracted canola meal (JSECM), Brassica napus solvent-extracted canola meal (NSECM), B. napus expeller-pressed canola meal (NEPCM) and B. napus cold-pressed canola cake (NCPCC) in comparison with soybean meal (SBM). Samples were hydrolysed in two steps using pepsin and pancreatin. Subsequently, residues were incubated in a buffer solution with fresh pig faeces as inocula for 72 h to measure gas production. Concentration of volatile fatty acids (VFA) per gram of dry matter (DM) of feedstuff was measured in fermented solutions. Apparent ileal digestibility (AID) and apparent hindgut fermentation (AHF) of gross energy (GE) for feedstuffs were obtained from pigs fed the same feedstuffs. On DM basis, SBM, JSECM, NSECM, NEPCM and NCPCC contained 15, 19, 22, 117 and 231 g/kg ether extract; and 85, 223, 306, 208 and 176 g/kg NDF, respectively. In vitro digestibility of DM (IVDDM) of SBM (82.3%) was greater (P<0.05) than that of JSECM (68.5%), NSECM (63.4%), NEPCM (67.5%) or NCPCC (69.8%). The JSECM had greater (P<0.05) IVDDM than NSECM. The IVDDM for NSECM was lower (P<0.05) than that for NEPCM, which was lower (P<0.05) than that for NCPCC. Similarly, AID of GE was greatest for SBM followed by NCPCC, JSECM, NEPCM and then NSECM. Total VFA production for SBM (0.73 mmol/g) was lower (P<0.05) than that of JSECM (1.38 mmol/g) or NSECM (1.05 mmol/g), but not different from that of NEPCM (0.80 mmol/g) and NCPCC (0.62 mmol/g). Total VFA production of JSECM was greater (P<0.05) than that of NSECM. Total VFA production of NSECM was greater (P<0.05) than that of NEPCM or NCPCC, which differed (P<0.05). The ranking of feedstuffs for total VFA production was similar to AHF of GE. In conclusion, in vitro fermentation characteristics of canola co-products and SBM simulated their fermentation in the small and large intestine of pigs, respectively. The 30% greater VFA production for JSECM than NSECM due to lower lignified fibre of JSECM indicates that fermentation characteristics differ between canola species. The NSECM had the highest fermentability followed by NEPCM and then NCPCC, indicating that fat in canola co-products can limit their fermentability in the hindgut.

Aerobic performance and body composition changes during military service

PubMed Central

Mikkola, Ilona; Keinänen-Kiukaanniemi, Sirkka; Jokelainen, Jari; Peitso, Ari; Härkönen, Pirjo; Timonen, Markku; Ikäheimo, Tiina

2012-01-01

Objective To examine the association between aerobic performance and body composition changes by body mass index (BMI). Design 6–12 months’ follow-up during military service. Setting Conscripts entering military service in 2005 in Sodankylä Jaeger Brigade (Finland). Subjects 945 men (19 years, SD 1 years). Main outcome measures Height, weight, waist circumference, BMI, and aerobic performance (Cooper test) were recorded. Body composition was measured by bioelectrical impedance analysis (BIA). The measured parameters were fat mass (FM), fat free mass (FFM), and visceral fat area (VFA). All the measurements were performed at the beginning and end of service. Results On average, the military training period improved the running distance by 6.8% (169 m, p < 0.001) and the improvements were more pronounced in overweight (223.9 m/9.5%, p < 0.001) and obese (273.3 m/13.6 %, p < 0.001) conscripts. A strong inverse correlation between aerobic performance and body composition changes was observed, especially for weight (r = –0.305, p < 0.001) and VFA (r = –0.465, p < 0.001). A significant association between aerobic performance and changes in weight (p < 0.001), waist circumference (p < 0.001), FM (p < 0.001), and VFA (p < 0.001) by BMI was detected. The associated decrease in weight, waist circumference, FM, and VFA with improved aerobic performance was more substantial between overweight and obese compared with normal-weight subjects. Conclusions Favourable changes in body composition are associated with improved aerobic performance during a physical training period such as military service. These findings are pronounced among overweight and obese men and can be applied at the population level in reducing obesity and co-morbidities. PMID:22643154

Replication study of 15 recently published Loci for body fat distribution in the Japanese population.

PubMed

Hotta, Kikuko; Kitamoto, Aya; Kitamoto, Takuya; Mizusawa, Seiho; Teranishi, Hajime; So, Rina; Matsuo, Tomoaki; Nakata, Yoshio; Hyogo, Hideyuki; Ochi, Hidenori; Nakamura, Takahiro; Kamohara, Seika; Miyatake, Nobuyuki; Kotani, Kazuaki; Itoh, Naoto; Mineo, Ikuo; Wada, Jun; Yoneda, Masato; Nakajima, Atsushi; Funahashi, Tohru; Miyazaki, Shigeru; Tokunaga, Katsuto; Masuzaki, Hiroaki; Ueno, Takato; Chayama, Kazuaki; Hamaguchi, Kazuyuki; Yamada, Kentaro; Hanafusa, Toshiaki; Oikawa, Shinichi; Sakata, Toshiie; Tanaka, Kiyoji; Matsuzawa, Yuji; Nakao, Kazuwa; Sekine, Akihiro

2013-01-01

Visceral fat accumulation plays an integral role in morbidity and mortality rates by increasing the risk of developing metabolic disorders such as type 2 diabetes, dyslipidemia, and hypertension. New genetic loci associated with fat distribution, measured by waist-hip ratios and computed tomography (CT), have recently been identified by genome-wide association studies in European-descent populations. This study used CT to investigate whether single nucleotide polymorphisms (SNPs) that confer susceptibility to fat distribution are associated with visceral fat area (VFA) and subcutaneous fat area (SFA) in the Japanese population. We measured the VFAs and SFAs of 1424 obese Japanese subjects (BMI≥25 kg/m(2), 635 men and 789 women) that were genotyped at 15 SNPs, namely, TBX15 rs984222, DNM3 rs1011731, LYPLAL1 rs4846567, GRB14 rs10195252, NISCH rs6784615, ADAMTS9 rs6795735, CPEB4 rs6861681, LY86 rs1294421, VEGFA rs6905288, RSPO3 rs9491696, NFE2L3 rs1055144, ITPR2 rs718314, HOXC13 rs1443512, ZNRF3 rs4823006 and THNSL2 rs1659258. The G-allele of LYPLAL1 rs4846567 was borderline associated with an increased ratio of VFA to SFA (V/S ratio; p= 0.0020). LYPLAL1 rs4846567 had a stronger effect on the V/S ratio in women (p= 0.0078) than in men (p= 0.12); however, neither result was significant after Bonferroni correction for multiple comparisons. NISCH rs6784615 was nominally associated with increased VFA (p=0.040) and V/S ratio (p= 0.020). The other SNPs analyzed were not significantly associated with body mass index (BMI), VFA, or SFA. Our results suggest that LYPLAL1 rs4846567 and NISCH rs6784615 may influence fat distribution in the Japanese population.

Quantification of volatile fatty acids from cattle manure via non-catalytic esterification for odour indication.

PubMed

Lee, Sang-Ryong; Lee, Jechan; Cho, Seong-Heon; Kim, Jieun; Oh, Jeong-Ik; Tsang, Daniel C W; Jeong, Kwang-Hwa; Kwon, Eilhann E

2018-01-01

This report proposes a new approach to evaluate the odour nuisance of cattle manure samples from three different cattle breeds (i.e., native cattle, beef cattle, and milk cow) by means of quantification and speciation of volatile fatty acids (VFAs). To this end, non-catalytic esterification thermally induced in the presence of a porous material (silica) was undertaken, and the optimal operational parameters such as the derivatizing temperature (330°C) for the maximum yield (≥99±0.4%) of volatile fatty acid methyl esters (VFAMEs) were established. Among the VFA species in cattle manure based on quantification of VFAs, the major species were acetic, butyric and valeric acid. Considering the odour threshold of each VFA, our experimental results suggested that the major contributors to odour nuisance were C 4-5 VFA species (i.e., butyric and valeric acid). Hydrothermal treatment was performed at 150°C for 0-40min to correlate the formation of VFAs with different types of cattle feed formulations. Our experimental data demonstrated that the formation of total VFAs is linearly proportional to the hydrothermal treatment duration and the total content of VFAs in native cattle, beef cattle, and milk cow manure samples reached up to ~1000, ~3200, and ~2800ppm, respectively. Thus, this study demonstrated that the degree of VFA formation is highly dependent on cattle feed formulations, which rely significantly on the protein content. Furthermore, the hydrothermal treatment provides a favourable condition for generating more VFAs. In this context, producing cattle manure into refused derived fuel (RDF) via a hydrothermal treatment is not a viable option to control odour. Copyright © 2017 Elsevier B.V. All rights reserved.

Prevalence of silent vertebral fractures detected by vertebral fracture assessment in young Portuguese men with hyperthyroidism.

PubMed

Barbosa, Ana Paula; Rui Mascarenhas, Mário; Silva, Carlos Francisco; Távora, Isabel; Bicho, Manuel; do Carmo, Isabel; de Oliveira, António Gouveia

2015-02-01

Hyperthyroidism is a risk factor for reduced bone mineral density (BMD) and osteoporotic fractures. Vertebral fracture assessment (VFA) by dual-energy X-ray absorptiometry (DXA) is a radiological method of visualization of the spine, which enables patient comfort and reduced radiation exposure. This study was carried out to evaluate BMD and the prevalence of silent vertebral fractures in young men with hyperthyroidism. We conducted a cross-sectional study in a group of Portuguese men aged up to 50 years and matched in hyperthyroidism (n=24) and control (n=24) groups. A group of 48 Portuguese men aged up to 50 years was divided and matched in hyperthyroidism (n=24) and control (n=24) groups. BMD (g/cm(2)) at L1-L4, hip, radius 33%, and whole body as well as the total body masses (kg) were studied by DXA. VFA was used to detect fractures and those were classified by Genant's semiquantitative method. No patient had previously been treated for hyperthyroidism, osteoporosis, or low bone mass. Adequate statistical tests were used. The mean age, height, and total fat mass were similar in both groups (P≥0.05). The total lean body mass and the mean BMD at lumbar spine, hip, and whole body were significantly decreased in the hyperthyroidism group. In this group, there was also a trend for an increased prevalence of reduced BMD/osteoporosis and osteoporotic vertebral fractures. The results obtained using VFA technology (confirmed by X-ray) suggest that the BMD changes in young men with nontreated hyperthyroidism may lead to the development of osteoporosis and vertebral fractures. This supports the pertinence of using VFA in the routine of osteoporosis assessment to detect silent fractures precociously and consider early treatment. © 2015 European Society of Endocrinology.

Methane Production of Different Forages in In vitro Ruminal Fermentation

PubMed Central

Meale, S. J.; Chaves, A. V.; Baah, J.; McAllister, T. A.

2012-01-01

An in vitro rumen batch culture study was completed to compare effects of common grasses, leguminous shrubs and non-leguminous shrubs used for livestock grazing in Australia and Ghana on CH4 production and fermentation characteristics. Grass species included Andropodon gayanus, Brachiaria ruziziensis and Pennisetum purpureum. Leguminous shrub species included Cajanus cajan, Cratylia argentea, Gliricidia sepium, Leucaena leucocephala and Stylosanthes guianensis and non-leguminous shrub species included Annona senegalensis, Moringa oleifera, Securinega virosa and Vitellaria paradoxa. Leaves were harvested, dried at 55°C and ground through a 1 mm screen. Serum bottles containing 500 mg of forage, modified McDougall’s buffer and rumen fluid were incubated under anaerobic conditions at 39°C for 24 h. Samples of each forage type were removed after 0, 2, 6, 12 and 24 h of incubation for determination of cumulative gas production. Methane production, ammonia concentration and proportions of VFA were measured at 24 h. Concentration of aNDF (g/kg DM) ranged from 671 to 713 (grasses), 377 to 590 (leguminous shrubs) and 288 to 517 (non-leguminous shrubs). After 24 h of in vitro incubation, cumulative gas, CH4 production, ammonia concentration, proportion of propionate in VFA and IVDMD differed (p<0.05) within each forage type. B. ruziziensis and G. sepium produced the highest cumulative gas, IVDMD, total VFA, proportion of propionate in VFA and the lowest A:P ratios within their forage types. Consequently, these two species produced moderate CH4 emissions without compromising digestion. Grazing of these two species may be a strategy to reduce CH4 emissions however further assessment in in vivo trials and at different stages of maturity is recommended. PMID:25049482

Investigation into the effect of high concentrations of volatile fatty acids in anaerobic digestion on methanogenic communities

PubMed Central

Franke-Whittle, Ingrid H.; Walter, Andreas; Ebner, Christian; Insam, Heribert

2014-01-01

A study was conducted to determine whether differences in the levels of volatile fatty acids (VFAs) in anaerobic digester plants could result in variations in the indigenous methanogenic communities. Two digesters (one operated under mesophilic conditions, the other under thermophilic conditions) were monitored, and sampled at points where VFA levels were high, as well as when VFA levels were low. Physical and chemical parameters were measured, and the methanogenic diversity was screened using the phylogenetic microarray ANAEROCHIP. In addition, real-time PCR was used to quantify the presence of the different methanogenic genera in the sludge samples. Array results indicated that the archaeal communities in the different reactors were stable, and that changes in the VFA levels of the anaerobic digesters did not greatly alter the dominating methanogenic organisms. In contrast, the two digesters were found to harbour different dominating methanogenic communities, which appeared to remain stable over time. Real-time PCR results were inline with those of microarray analysis indicating only minimal changes in methanogen numbers during periods of high VFAs, however, revealed a greater diversity in methanogens than found with the array. PMID:25164858

Implementation of in-line infrared monitor in full-scale anaerobic digestion process.

PubMed

Spanjers, H; Bouvier, J C; Steenweg, P; Bisschops, I; van Gils, W; Versprille, B

2006-01-01

During start up but also during normal operation, anaerobic reactor systems should be run and monitored carefully to secure trouble-free operation, because the process is vulnerable to disturbances such as temporary overloading, biomass wash out and influent toxicity. The present method of monitoring is usually by manual sampling and subsequent laboratory analysis. Data collection, processing and feedback to system operation is manual and ad hoc, and involves high-level operator skills and attention. As a result, systems tend to be designed at relatively conservative design loading rates resulting in significant over-sizing of reactors and thus increased systems cost. It is therefore desirable to have on-line and continuous access to performance data on influent and effluent quality. Relevant variables to indicate process performance include VFA, COD, alkalinity, sulphate, and, if aerobic post-treatment is considered, total nitrogen, ammonia and nitrate. Recently, mid-IR spectrometry was demonstrated on a pilot scale to be suitable for in-line simultaneous measurement of these variables. This paper describes a full-scale application of the technique to test its ability to monitor continuously and without human intervention the above variables simultaneously in two process streams. For VFA, COD, sulphate, ammonium and TKN good agreement was obtained between in-line and manual measurements. During a period of six months the in-line measurements had to be interrupted several times because of clogging. It appeared that the sample pre-treatment unit was not able to cope with high solids concentrations all the time.

The effects of a ration change from a total mixed ration to pasture on rumen fermentation, volatile fatty acid absorption characteristics, and morphology of dairy cows.

PubMed

Schären, M; Seyfang, G M; Steingass, H; Dieho, K; Dijkstra, J; Hüther, L; Frahm, J; Beineke, A; von Soosten, D; Meyer, U; Breves, G; Dänicke, S

2016-05-01

To investigate the effect of the change from a concentrate and silage-based ration (total mixed ration, TMR) to a pasture-based ration, a 10-wk trial (wk 1-10) was performed, including 10 rumen- and duodenum-fistulated German Holstein dairy cows (182±24 d in milk, 23.5±3.5kg of milk/d; mean ± standard deviation). The cows were divided in either a pasture group (PG, n=5) or a confinement group (CG, n=5). The CG stayed on a TMR-based ration (35% corn silage, 35% grass silage, 30% concentrate; dry matter basis), whereas the PG was gradually transitioned from a TMR to a pasture-based ration (wk 1: TMR only; wk 2: 3 h/d on pasture wk 3 and 4: 12 h/d on pasture wk 5-10: pasture only). Ruminal pH, volatile fatty acids (VFA), NH3-N, and lipopolysaccharide (LPS) concentrations were measured in rumen fluid samples collected medially and ventrally on a weekly basis. Ruminal pH was continuously recorded during 1 to 4 consecutive days each week using ruminal pH measuring devices. In wk 1, 5, and 10, rumen contents were evacuated and weighed, papillae were collected from 3 locations in the rumen, and subsequently a VFA absorption test was performed. In the PG, mean rumen pH and molar acetate proportions decreased, and molar butyrate proportions increased continuously over the course of the trial, which can most likely be ascribed to an increased intake of rapidly fermentable carbohydrates. During the first weeks on a full grazing ration (wk 5-7), variation of rumen pH decreased, and in wk 5 a lower rumen content, papillae surface area, and potential for VFA absorption were observed. In wk 8 to 10, variation of rumen pH and total VFA concentrations increased again, and acetate/propionate ratio decreased. In wk-10 rumen content, papillae area and VFA absorption characteristics similar to initial levels were observed. Although continuous rumen pH assessments and LPS concentrations did not reveal an increased risk for subacute rumen acidosis (SARA) during the adaption period, histopathology of rumen papillae and potential for VFA absorption indicated a possible risk for rumen health. An increased risk for SARA was observed in wk 9 and 10 in the PG, but rumen LPS concentrations and histopathology were not adversely affected. Results of the present study suggest that after behavioral and metabolic adaptation to the transition from a TMR to a pasture-based ration, no adverse effects on rumen morphology and absorption capacity occurred, although rumen pH after adaptation to pasture indicated increased risk of SARA. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Gas-liquid chromatography in the diagnosis of anaerobic infections: a three year experience.

PubMed Central

Watt, B; Geddes, P A; Greenan, O A; Napier, S K; Mitchell, A

1982-01-01

Nearly two thousand clinical samples were examined by direct gas-liquid chromatography over a three year period. Absence of volatile fatty acids (VFAs) in the samples correlated well with negative culture results for anaerobic bacteria. In general the presence of acetic acid alone correlated well with the presence of aerobic organisms, whereas the presence of a mixture of VFAs correlated well with the presence of anaerobic organisms, either alone or in combination with aerobes. However a proportion of such VFA-positive samples gave no growth on culture. Swabs gave comparable results to samples of pus or exudates except that a higher proportion of the former were VFA-negative but culture positive. PMID:7096590

Mechanical sludge disintegration for the production of carbon source for biological nutrient removal.

PubMed

Kampas, P; Parsons, S A; Pearce, P; Ledoux, S; Vale, P; Churchley, J; Cartmell, E

2007-04-01

The primary driver for a successful biological nutrient removal is the availability of suitable carbon source, mainly in the form of volatile fatty acids (VFA). Several methods have been examined to increase the amount of VFAs in wastewater. This study investigates the mechanism of mechanical disintegration of thickened surplus activated sludge by a deflaker technology for the production of organic matter. This equipment was able to increase the soluble carbon in terms of VFA and soluble chemical oxygen demand (SCOD) with the maximum concentration to be around 850 and 6530 mgl(-1), for VFA and SCOD, respectively. The particle size was reduced from 65.5 to 9.3 microm after 15 min of disintegration with the simultaneous release of proteins (1550 mgl(-1)) and carbohydrates (307 mgl(-1)) indicating floc disruption and breakage. High performance size exclusion chromatography investigated the disintegrated sludge and confirmed that the deflaker was able to destroy the flocs releasing polymeric substances that are typically found outside of cells. When long disintegration times were applied (>or=10 min or >or=9000 kJkg(-1)TS of specific energy) smaller molecular size materials were released to the liquid phase, which are considered to be found inside the cells indicating cell lysis.

Control of amphibious weed ipomoea (Ipomoea carnea) by utilizing it for the extraction of volatile fatty acids as energy precursors.

PubMed

Rafiq Kumar, M; Tauseef, S M; Abbasi, Tasneem; Abbasi, S A

2015-01-01

Volatile fatty acids (VFAs), comprising mainly of acetic acid and lesser quantities of propionic and butyric acids, are generated when zoomass or phytomass is acted upon by acidogenic and acetogenic microorganisms. VFAs can be utilized by methanogens under anaerobic conditions to generate flammable methane-carbon dioxide mixtures known as 'biogas'. Acting on the premise that this manner of VFA utilization for generating relatively clean energy can be easily accomplished in a controlled fashion in conventional biogas plants as well as higher-rate anaerobic digesters, we have carried out studies aimed to generate VFAs from the pernicious weed ipomoea (Ipomoea carnea). The VFA extraction was accomplished by a simple yet effective technology, appropriate for use even by laypersons. For this acid-phase reactors were set, to which measured quantities of ipomoea leaves were charged along with water inoculated with cow dung. The reactors were stirred intermittently. It was found that VFA production started within hours of the mixing of the reactants and peaked by the 10(th) or 11(th) day in all the reactors, effecting a conversion of over 10% of the biomass into VFAs. The reactor performance had good reproducibility and the process appeared easily controllable, frugal and robust.

Control of amphibious weed ipomoea (Ipomoea carnea) by utilizing it for the extraction of volatile fatty acids as energy precursors

PubMed Central

Rafiq Kumar, M.; Tauseef, S.M.; Abbasi, Tasneem; Abbasi, S.A.

2014-01-01

Volatile fatty acids (VFAs), comprising mainly of acetic acid and lesser quantities of propionic and butyric acids, are generated when zoomass or phytomass is acted upon by acidogenic and acetogenic microorganisms. VFAs can be utilized by methanogens under anaerobic conditions to generate flammable methane–carbon dioxide mixtures known as ‘biogas’. Acting on the premise that this manner of VFA utilization for generating relatively clean energy can be easily accomplished in a controlled fashion in conventional biogas plants as well as higher-rate anaerobic digesters, we have carried out studies aimed to generate VFAs from the pernicious weed ipomoea (Ipomoea carnea). The VFA extraction was accomplished by a simple yet effective technology, appropriate for use even by laypersons. For this acid-phase reactors were set, to which measured quantities of ipomoea leaves were charged along with water inoculated with cow dung. The reactors were stirred intermittently. It was found that VFA production started within hours of the mixing of the reactants and peaked by the 10th or 11th day in all the reactors, effecting a conversion of over 10% of the biomass into VFAs. The reactor performance had good reproducibility and the process appeared easily controllable, frugal and robust. PMID:25685545

Enhancement of volatile fatty acid production and biogas yield from food waste following sonication pretreatment.

PubMed

Liu, Nuo; Jiang, Jianguo; Yan, Feng; Gao, Yuchen; Meng, Yuan; Aihemaiti, Aikelaimu; Ju, Tongyao

2018-07-01

The positive effect of sonication on volatile fatty acid (VFA) and hydrogen production was investigated by batch experiments. Several sonication densities (2, 1.6, and 1.2 W/mL) and times (5, 10, and 15 min) were tested. The optimal sonication condition was ultrasonic density 2 W/mL and ultrasonic time 15 min (2-U15). The FW particle size larger than 50 μm (d > 50 μm) were more susceptible to the sonication treatment than the smaller particle size (d ≤ 50 μm). The SCOD increased and VS reduction accelerated under sonication treatment. The maximum VFA production and the highest proportion of hydrogen in the biogas increased 65.3% and 59.1%, respectively, under the optimal sonication conditions compared to the unsonicated batch. Moreover, a reduction of over 50% in the time required to reach its maximum production was also observed. Butyric acid fermentation type was obtained whether following sonication treatment or not. The composition of key microbial community differed under the various sonication conditions. The genera Clostridium and Parabacteroides are predominantly responsible for VFA generation and both were found to be abundant under the optimal condition. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparison of laser ray-tracing and skiascopic ocular wavefront-sensing devices

PubMed Central

Bartsch, D-UG; Bessho, K; Gomez, L; Freeman, WR

2009-01-01

Purpose To compare two wavefront-sensing devices based on different principles. Methods Thirty-eight healthy eyes of 19 patients were measured five times in the reproducibility study. Twenty eyes of 10 patients were measured in the comparison study. The Tracey Visual Function Analyzer (VFA), based on the ray-tracing principle and the Nidek optical pathway difference (OPD)-Scan, based on the dynamic skiascopy principle were compared. Standard deviation (SD) of root mean square (RMS) errors was compared to verify the reproducibility. We evaluated RMS errors, Zernike terms and conventional refractive indexes (Sph, Cyl, Ax, and spherical equivalent). Results In RMS errors reading, both devices showed similar ratios of SD to the mean measurement value (VFA: 57.5±11.7%, OPD-Scan: 53.9±10.9%). Comparison on the same eye showed that almost all terms were significantly greater using the VFA than using the OPD-Scan. However, certain high spatial frequency aberrations (tetrafoil, pentafoil, and hexafoil) were consistently measured near zero with the OPD-Scan. Conclusion Both devices showed similar level of reproducibility; however, there was considerable difference in the wavefront reading between machines when measuring the same eye. Differences in the number of sample points, centration, and measurement algorithms between the two instruments may explain our results. PMID:17571088

Methanogenesis at low temperatures by microflora of tundra wetland soil.

PubMed

Kotsyurbenko, O R; Nozhevnikova, A N; Soloviova, T I; Zavarzin, G A

1996-01-01

Active methanogenesis from organic matter contained in soil samples from tundra wetland occurred even at 6 degrees C. Methane was the only end product in balanced microbial community with H2/CO2 as a substrate, besides acetate was produced as an intermediate at temperatures below 10 degrees C. The activity of different microbial groups of methanogenic community in the temperature range of 6-28 degrees C was investigated using 5% of tundra soil as inoculum. Anaerobic microflora of tundra wetland fermented different organic compounds with formation of hydrogen, volatile fatty acids (VFA) and alcohols. Methane was produced at the second step. Homoacetogenic and methanogenic bacteria competed for such substrates as hydrogen, formate, carbon monoxide and methanol. Acetogens out competed methanogens in an excess of substrate and low density of microbial population. Kinetic analysis of the results confirmed the prevalence of hydrogen acetogenesis on methanogenesis. Pure culture of acetogenic bacteria was isolated at 6 degrees C. Dilution of tundra soil and supply with the excess of substrate disbalanced the methanoigenic microbial community. It resulted in accumulation of acetate and other VFA. In balanced microbial community obviously autotrophic methanogens keep hydrogen concentration below a threshold for syntrophic degradation of VFA. Accumulation of acetate- and H2/CO2-utilising methanogens should be very important in methanogenic microbial community operating at low temperatures.

Implementation and process analysis of pilot scale multi-phase anaerobic fermentation and digestion of faecal sludge in Ghana

PubMed Central

Shih, Justin; Fanyin-Martin, Ato; Taher, Edris; Chandran, Kartik

2017-01-01

Background.  In Ghana, faecal sludge (FS) from on-site sanitation facilities is often discharged untreated into the environment, leading to significant insults to environmental and human health. Anaerobic digestion offers an attractive pathway for FS treatment with the concomitant production of energy in the form of methane. Another innovative option includes separating digestion into acidogenesis (production of volatile fatty acids (VFA)) and methanogenesis (production of methane), which could ultimately facilitate the production of an array of biofuels and biochemicals from the VFA. This work describes the development, implementation and modeling based analysis of a novel multiphase anaerobic fermentation-digestion process aimed at FS treatment in Kumasi, Ghana.  Methods.  A pilot-scale anaerobic fermentation process was implemented at the Kumasi Metropolitan Assembly’s Oti Sanitary Landfill Site at Adanse Dompoase.  The process consisted of six 10 m reactors in series, which were inoculated with bovine rumen and fed with fecal sludge obtained from public toilets.  The performance of the fermentation process was characterized in terms of both aqueous and gaseous variables representing the conversion of influent organic carbon to VFA as well as CH 4.  Using the operating data, the first-ever process model for FS fermentation and digestion was developed and calibrated, based on the activated sludge model framework. Results and Conclusions.  This work represents one of the first systematic efforts at integrated FS characterization and process modeling to enable anaerobic fermentation and digestion of FS. It is shown that owing to pre-fermentation of FS in public septage holding tanks, one could employ significantly smaller digesters (lower capital costs) or increased loading capabilities for FS conversion to biogas or VFA. Further, using the first-ever calibrated process model for FS fermentation and digestion presented herein, we expect improved and more mechanistically informed development and application of different process designs and configurations for global FS management practice. PMID:29528044

Use of Acetate, Propionate, and Butyrate for Reduction of Nitrate and Sulfate and Methanogenesis in Microcosms and Bioreactors Simulating an Oil Reservoir

PubMed Central

Shen, Yin; An, Dongshan; Voordouw, Gerrit

2017-01-01

ABSTRACT Acetate, propionate, and butyrate (volatile fatty acids [VFA]) occur in oil field waters and are frequently used for microbial growth of oil field consortia. We determined the kinetics of use of these VFA components (3 mM each) by an anaerobic oil field consortium in microcosms containing 2 mM sulfate and 0, 4, 6, 8, or 13 mM nitrate. Nitrate was reduced first, with a preference for acetate and propionate. Sulfate reduction then proceeded with propionate (but not butyrate) as the electron donor, whereas the fermentation of butyrate (but not propionate) was associated with methanogenesis. Microbial community analyses indicated that Paracoccus and Thauera (Paracoccus-Thauera), Desulfobulbus, and Syntrophomonas-Methanobacterium were the dominant taxa whose members catalyzed these three processes. Most-probable-number assays showed the presence of up to 107/ml of propionate-oxidizing sulfate-reducing bacteria (SRB) in waters from the Medicine Hat Glauconitic C field. Bioreactors with the same concentrations of sulfate and VFA responded similarly to increasing concentrations of injected nitrate as observed in the microcosms: sulfide formation was prevented by adding approximately 80% of the nitrate dose needed to completely oxidize VFA to CO2 in both. Thus, this work has demonstrated that simple time-dependent observations of the use of acetate, propionate, and butyrate for nitrate reduction, sulfate reduction, and methanogenesis in microcosms are a good proxy for these processes in bioreactors, monitoring of which is more complex. IMPORTANCE Oil field volatile fatty acids acetate, propionate, and butyrate were specifically used for nitrate reduction, sulfate reduction, and methanogenic fermentation. Time-dependent analyses of microcosms served as a good proxy for these processes in a bioreactor, mimicking a sulfide-producing (souring) oil reservoir: 80% of the nitrate dose required to oxidize volatile fatty acids to CO2 was needed to prevent souring in both. Our data also suggest that propionate is a good substrate to enumerate oil field SRB. PMID:28130297

Implementation and process analysis of pilot scale multi-phase anaerobic fermentation and digestion of faecal sludge in Ghana.

PubMed

Shih, Justin; Fanyin-Martin, Ato; Taher, Edris; Chandran, Kartik

2017-11-06

Background.  In Ghana, faecal sludge (FS) from on-site sanitation facilities is often discharged untreated into the environment, leading to significant insults to environmental and human health. Anaerobic digestion offers an attractive pathway for FS treatment with the concomitant production of energy in the form of methane. Another innovative option includes separating digestion into acidogenesis (production of volatile fatty acids (VFA)) and methanogenesis (production of methane), which could ultimately facilitate the production of an array of biofuels and biochemicals from the VFA. This work describes the development, implementation and modeling based analysis of a novel multiphase anaerobic fermentation-digestion process aimed at FS treatment in Kumasi, Ghana.  Methods.  A pilot-scale anaerobic fermentation process was implemented at the Kumasi Metropolitan Assembly's Oti Sanitary Landfill Site at Adanse Dompoase.  The process consisted of six 10 m reactors in series, which were inoculated with bovine rumen and fed with fecal sludge obtained from public toilets.  The performance of the fermentation process was characterized in terms of both aqueous and gaseous variables representing the conversion of influent organic carbon to VFA as well as CH 4 .  Using the operating data, the first-ever process model for FS fermentation and digestion was developed and calibrated, based on the activated sludge model framework. Results and Conclusions.  This work represents one of the first systematic efforts at integrated FS characterization and process modeling to enable anaerobic fermentation and digestion of FS. It is shown that owing to pre-fermentation of FS in public septage holding tanks, one could employ significantly smaller digesters (lower capital costs) or increased loading capabilities for FS conversion to biogas or VFA. Further, using the first-ever calibrated process model for FS fermentation and digestion presented herein, we expect improved and more mechanistically informed development and application of different process designs and configurations for global FS management practice.

Comparison of microbial fermentation of high- and low-forage diets in Rusitec, single-flow continuous-culture fermenters and sheep rumen.

PubMed

Carro, M D; Ranilla, M J; Martín-García, A I; Molina-Alcaide, E

2009-04-01

Eight Rusitec and eight single-flow continuous-culture fermenters (SFCCF) were used to compare the ruminal fermentation of two diets composed of alfalfa hay and concentrate in proportions of 80 : 20 (F80) and 20 : 80 (F20). Results were validated with those obtained previously in sheep fed the same diets. Rusitec fermenters were fed once daily and SFCCF twice, but liquid dilution rates were similar in both types of fermenters. Mean values of pH over the 12 h postfeeding were higher (P < 0.001) in Rusitec than in SFCCF, with diet F80 showing higher values (P < 0.001) in both types of fermenters. Concentrations of total volatile fatty acids (VFA) were higher (P < 0.001) in SFCCF than in Rusitec, and in both systems were higher (P = 0.002) for diet F20 than for diet F80. There were significant differences between systems in the proportions of the main VFA, and a fermentation system × diet interaction (P < 0.001) was detected for all VFA with the exception of valerate. No differences (P = 0.145) between the two types of fermenters were detected in dry matter (DM) digestibility, but NDF, microbial N flow and its efficiency were higher (P = 0.001) in SFCCF compared to Rusitec. Whereas pH values and VFA concentrations remained fairly stable through the day in both in vitro systems, pH dropped and VFA increased shortly after feeding in sheep rumen reaching the minimum and maximal values, respectively, about 4 h after feeding. Both in vitro systems detected differences between diets similar to those found in sheep for liquid dilution rate, pH values, DM digestibility, microbial N flow and growth efficiency. In contrast, acetate/propionate ratios were lower for diet F20 than for F80 in sheep rumen (2.73 and 3.97) and SFCCF (3.07 and 4.80), but were higher for diet F20 compared to F80 (4.29 and 3.40) in Rusitec, with values considered to be unphysiological for high-concentrate diets. In vivo NDF digestibility was affected (P = 0.017) by diet, but no differences between diets (P > 0.05) were found in any in vitro system. A more precise control of pH in both types of fermenters and a reduction of concentrate retention time in Rusitec could probably improve the simulation of in vivo fermentation.

Effects of supplemental energy and protein on forage digestion and urea kinetics in growing beef cattle.

PubMed

Bailey, E A; Titgemeyer, E C; Olson, K C; Brake, D W; Jones, M L; Anderson, D E

2012-10-01

Effects of supplemental energy sources on nutrient digestion and urea kinetics at 2 levels of degradable intake protein were evaluated in cattle (Bos taurus). Six ruminally and duodenally cannulated steers (208 ± 17 kg) were used in a 6 × 6 Latin square with treatments arranged as a 3 × 2 factorial. Energy treatments included a control, 600 g glucose dosed ruminally once daily, and 480 g VFA infused ruminally over 8 h daily. Casein (120 or 240 g) was dosed ruminally once daily. Steers had ad libitum access to prairie hay (5.8% CP). Jugular infusion of (15)N(15)N-urea with measurement of enrichment in urine was used to measure urea kinetics. Infusing VFA decreased (P < 0.01) forage intake by 27%. Supplementing glucose decreased (P < 0.01) total tract NDF digestibility and tended to decrease ruminal NDF digestibility; depressions in response to glucose tended to be greater at the lower level of casein. Increasing casein decreased (P < 0.02) ruminal pH. Infusing VFA decreased pH only during infusions, whereas glucose decreased pH 2 h after dosing. Ruminal concentrations of NH(3), acetate, and propionate decreased and butyrate concentration increased when glucose was supplemented. Increasing casein supplementation increased (P < 0.01) ruminal concentrations of NH(3), acetate, and propionate. Supplemental energy decreased (P = 0.03) plasma urea-N concentration, but casein level did not affect it (P = 0.16). Microbial N flow was greater (P < 0.04) for 240 than for 120 g/d casein but was not affected by supplemental energy (P = 0.23). Urea-N entry rate and gut entry of urea-N were not affected (P ≥ 0.12) by supplemental energy or casein, but the proportion of urea production that was recycled to the gut was less (P = 0.01) when 240 g/d rather than 120 g/d casein was provided. Compared with VFA, glucose tended (P = 0.07) to increase the proportion of urea-N entry rate that was recycled to the gut. Supplementation with glucose led to more (P = 0.01) microbial uptake of recycled urea than did supplementation with VFA. Urea recycling did not differ greatly among treatments despite impacts on ruminal pH and NH(3) and on plasma urea-N that were expected to alter urea transport across ruminal epithelium. Lack of treatment effects on urea production indicate that the complete diets did not provide excessive amounts of N and that increases of intestinally available AA were used efficiently by cattle for protein deposition.

Sensor Data Qualification Technique Applied to Gas Turbine Engines

NASA Technical Reports Server (NTRS)

Csank, Jeffrey T.; Simon, Donald L.

2013-01-01

This paper applies a previously developed sensor data qualification technique to a commercial aircraft engine simulation known as the Commercial Modular Aero-Propulsion System Simulation 40,000 (C-MAPSS40k). The sensor data qualification technique is designed to detect, isolate, and accommodate faulty sensor measurements. It features sensor networks, which group various sensors together and relies on an empirically derived analytical model to relate the sensor measurements. Relationships between all member sensors of the network are analyzed to detect and isolate any faulty sensor within the network.

Products derived from olive leaves and fruits can alter in vitro ruminal fermentation and methane production.

PubMed

Shakeri, Pirouz; Durmic, Zoey; Vadhanabhuti, Joy; Vercoe, Philip E

2017-03-01

The industrial processing of olive generates a high quantity of by-products. The objective of this study was to examine the effects of products derived from olive trees, i.e. leaves, fruits or kernels as a sole substrate (part A), and crude extract from leaves combined with a substrate (part B) on rumen microbial fermentation in an in vitro batch fermentation system. In this study, total gas production, methane production, and concentrations of volatile fatty acids (VFA) and ammonia in ruminal fluid were measured. In part A, in vitro fermentation of leaves or fruits yielded a gas and total VFA production that were comparable with control substrate, while most of them produced significantly less methane (up to 55.6%) when compared to control substrate. In part B, amongst leaf extracts, only addition of chloroform extract reduced methane production, which was also associated with a decrease (P < 0.01) in gas production. This effect was associated with a significant reduction (P < 0.01) in acetate to propionate ratio and ammonia production, but not in reduction in VFA concentrations. Olive leaf and olive leaf chloroform extract reduced ammonia production and increased the molar proportion of propionate in the rumen and can assist in developing novel feed additives for methane mitigation from the rumen. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Effect of sugar fatty acid esters on rumen fermentation in vitro.

PubMed

Wakita, M; Hoshino, S

1987-11-01

1. The effect of sugar fatty acid esters (SFEs; currently used as food additives for human consumption) on rumen volatile fatty acids (VFA) and gas production was studied with sheep rumen contents in vitro. 2. Some SFEs having monoester contents of more than 70% increased the molar proportion of propionate in conjunction with reduction in the acetate:propionate ratio when the individual SFE was added to rumen contents in a final concentration of 4 g/l. Laurate sugar ester was the most potent propionate enhancer and rumen gas depressor, the effective dose being as low as 1 g/l in a final concentration. Fatty acid esters other than SFEs had little, if any, effect on rumen VFA production and their molar proportions. 3. Approximately 50% of laurate sugar ester was hydrolysed by in vitro incubation with rumen fluid for 2 h. The addition of fatty acids and sucrose was also effective in the alterations of rumen VFA and gas production. However, the effect of SFEs on in vitro rumen fermentation was significantly greater than that of their constituent fatty acids or sucrose, or both. Accordingly, the effect appeared to be ascribed to the complex action of SFE itself and to its constituents, free fatty acids and sucrose. 4. SFEs, at the level of 4 g/l, reduced substantially the froth formation (ingesta volume increase) and seemed to be effective for the prevention of bloat.

Dark fermentation process as pretreatment for a sustainable denaturation of asbestos containing wastes.

PubMed

Spasiano, Danilo

2018-05-05

A cement asbestos compound (CAC) sample was detoxified by a treatment train based on a dark fermentation (DF) process followed by a hydrothermal phase, which led to the complete degradation of the chrysotile fibers. During the biological pretreatment, the glucose was converted in biogas rich in H 2 and volatile fatty acids (VFA). The latter caused the dissolution of all the Ca-based compounds and the solubilisation of 50% brucite-like layers of chrysotile fibers contained in the CAC suspended in the bioreactor (5 g/L). XRD analysis of the solids contained in the effluents of the DF process highlighted the disappearance of the chrysotile fiber peaks. However, a complete destruction of all the asbestos fibers is hard to prove and a hydrothermal treatment was carried out to dissolve the "brucite" layers still present in solution. Due to the presence of the VFA produced during the DF, a complete destruction of chrysotile fibers was achieved by a 24 h hydrothermal process performed with a [H 2 SO 4 ]/[CAC] ratio 50% lower than that adopted in a previous finding. Consequently, the DF pre-treatment can contribute to lower the H 2 SO 4 and the energy consumption of a CAC hydrothermal treatment, due to the production of VFA and H 2 . Copyright © 2018 Elsevier B.V. All rights reserved.

Plasma Free Amino Acid Profiles Predict Four-Year Risk of Developing Diabetes, Metabolic Syndrome, Dyslipidemia, and Hypertension in Japanese Population

PubMed Central

Yamakado, Minoru; Nagao, Kenji; Imaizumi, Akira; Tani, Mizuki; Toda, Akiko; Tanaka, Takayuki; Jinzu, Hiroko; Miyano, Hiroshi; Yamamoto, Hiroshi; Daimon, Takashi; Horimoto, Katsuhisa; Ishizaka, Yuko

2015-01-01

Plasma free amino acid (PFAA) profile is highlighted in its association with visceral obesity and hyperinsulinemia, and future diabetes. Indeed PFAA profiling potentially can evaluate individuals’ future risks of developing lifestyle-related diseases, in addition to diabetes. However, few studies have been performed especially in Asian populations, about the optimal combination of PFAAs for evaluating health risks. We quantified PFAA levels in 3,701 Japanese subjects, and determined visceral fat area (VFA) and two-hour post-challenge insulin (Ins120 min) values in 865 and 1,160 subjects, respectively. Then, models between PFAA levels and the VFA or Ins120 min values were constructed by multiple linear regression analysis with variable selection. Finally, a cohort study of 2,984 subjects to examine capabilities of the obtained models for predicting four-year risk of developing new-onset lifestyle-related diseases was conducted. The correlation coefficients of the obtained PFAA models against VFA or Ins120 min were higher than single PFAA level. Our models work well for future risk prediction. Even after adjusting for commonly accepted multiple risk factors, these models can predict future development of diabetes, metabolic syndrome, and dyslipidemia. PFAA profiles confer independent and differing contributions to increasing the lifestyle-related disease risks in addition to the currently known factors in a general Japanese population. PMID:26156880

Reliable dual-redundant sensor failure detection and identification for the NASA F-8 DFBW aircraft

NASA Technical Reports Server (NTRS)

Deckert, J. C.; Desai, M. N.; Deyst, J. J., Jr.; Willsky, A. S.

1978-01-01

A technique was developed which provides reliable failure detection and identification (FDI) for a dual redundant subset of the flight control sensors onboard the NASA F-8 digital fly by wire (DFBW) aircraft. The technique was successfully applied to simulated sensor failures on the real time F-8 digital simulator and to sensor failures injected on telemetry data from a test flight of the F-8 DFBW aircraft. For failure identification the technique utilized the analytic redundancy which exists as functional and kinematic relationships among the various quantities being measured by the different control sensor types. The technique can be used not only in a dual redundant sensor system, but also in a more highly redundant system after FDI by conventional voting techniques reduced to two the number of unfailed sensors of a particular type. In addition the technique can be easily extended to the case in which only one sensor of a particular type is available.

Quartz Crystal Microbalance with Dissipation Monitoring

DTIC Science & Technology

2014-11-06

Hydroxyapatite , 10 nm, Sensors • Biotin Functionalized on Gold Sensors • His-tag Capturing Sensor QCM-D techniques provide answers about...UV/Ozone cleaner • Hydroxyapatite , 10 nm, Sensors • Biotin Functionalized on Gold Sensors • His-tag Capturing Sensor QCM-D techniques provide

Characteristics of dairy cows with a greater or lower risk of subacute ruminal acidosis: Volatile fatty acid absorption, rumen digestion, and expression of genes in rumen epithelial cells.

PubMed

Gao, X; Oba, M

2016-11-01

The objective of this study was to examine whether lactating dairy cows with a greater or lower risk of subacute ruminal acidosis (SARA) have differences in volatile fatty acid (VFA) absorption rate, expression of genes involved in VFA metabolism and intracellular pH regulation in rumen epithelial cells, and in situ carbohydrate digestibility in the rumen. We fed 14 ruminally cannulated mid-lactating dairy cows (119±47.2d in milk; body weight 640±47.9kg) a high-grain diet consisting of 30% forage ad libitum, with an 18-d diet adaptation and a 7-d sample and data collection period. Eight cows with the lowest acidosis index [area below pH 5.8 normalized for dry matter intake (DMI); 0.10±0.16 pH × min/kg of DMI] and 5 with the highest acidosis index (3.72±0.19 pH × min/kg of DMI) were classified as animals with lower risk (LS) and higher risk (HS) of SARA, respectively. Minimum (5.75 vs. 5.33) and mean rumen pH (6.33 vs. 5.98) were higher for LS than for HS cows. In addition, the duration and area of rumen pH below 5.8 was lower in LS cows (24.9 vs. 481min/d; 2.94 vs. 102 pH × min/d). Although DMI, milk yield, and milk component yields did not differ, milk fat concentration tended to be higher for LS cows than for HS cows (3.36 vs. 2.93%). However, we observed no difference in VFA absorption rate between LS and HS cows. In situ starch and neutral detergent fiber digestibility were not different between LS and HS cows, but the relative mRNA abundance of lanosterol synthase (LSS) was higher for LS cows than for HS cows. In addition, the mRNA abundance of hydroxy-3-methylglutaryl-CoA synthase 1 (HMGCS1) tended to be higher for LS cows than for HS cows. These results suggested that VFA absorption rate might not explain the difference in rumen pH between LS and HS cows in the current study, even though expression of some genes related to VFA metabolism in rumen epithelium may be associated with variation in the risk of SARA among lactating cows. This variation in the risk of SARA may not be attributed to differences in the capacity of rumen microbes to ferment carbohydrates, because in situ carbohydrate digestibility in the rumen was not different between cows with higher and lower risk of SARA. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Potential of tannin-rich plants for modulating ruminal microbes and ruminal fermentation in sheep.

PubMed

Rira, M; Morgavi, D P; Archimède, H; Marie-Magdeleine, C; Popova, M; Bousseboua, H; Doreau, M

2015-01-01

The objective of this work was to study nutritional strategies for decreasing methane production by ruminants fed tropical diets, combining in vitro and in vivo methods. The in vitro approach was used to evaluate the dose effect of condensed tannins (CT) contained in leaves of Gliricidia sepium, Leucaena leucocephala, and Manihot esculenta (39, 75, and 92 g CT/kg DM, respectively) on methane production and ruminal fermentation characteristics. Tannin-rich plants (TRP) were incubated for 24 h alone or mixed with a natural grassland hay based on Dichanthium spp. (control plant), so that proportions of TRP were 0, 0.25, 0.5, 0.75, and 1.0. Methane production, VFA concentration, and fermented OM decreased with increased proportions of TRP. Numerical differences on methane production and VFA concentration among TRP sources may be due to differences in their CT content, with greater effects for L. leucocephala and M. esculenta than for G. sepium. Independently of TRP, the response to increasing doses of CT was linear for methane production but quadratic for VFA concentration. As a result, at moderate tannin dose, methane decreased more than VFA. The in vivo trial was conducted to investigate the effect of TRP on different ruminal microbial populations. To this end, 8 rumen-cannulated sheep from 2 breeds (Texel and Blackbelly) were used in two 4 × 4 Latin square designs. Diets were fed ad libitum and were composed of the same feeds used for the in vitro trial: control plant alone or combined with pellets made from TRP leaves at 44% of the diet DM. Compared to TRP, concentration of Ruminococcus flavefaciens was greater for the control diet and concentration of Ruminococcus albus was least for the control diet. The methanogen population was greater for Texel than for Blackbelly. By contrast, TRP-containing diets did not affect protozoa or Fibrobacter succinogenes numbers. Hence, TRP showed potential for mitigating methane production by ruminants. These findings suggest that TRP fed as pellets could be used to decrease methane production.

Use of Acetate, Propionate, and Butyrate for Reduction of Nitrate and Sulfate and Methanogenesis in Microcosms and Bioreactors Simulating an Oil Reservoir.

PubMed

Chen, Chuan; Shen, Yin; An, Dongshan; Voordouw, Gerrit

2017-04-01

Acetate, propionate, and butyrate (volatile fatty acids [VFA]) occur in oil field waters and are frequently used for microbial growth of oil field consortia. We determined the kinetics of use of these VFA components (3 mM each) by an anaerobic oil field consortium in microcosms containing 2 mM sulfate and 0, 4, 6, 8, or 13 mM nitrate. Nitrate was reduced first, with a preference for acetate and propionate. Sulfate reduction then proceeded with propionate (but not butyrate) as the electron donor, whereas the fermentation of butyrate (but not propionate) was associated with methanogenesis. Microbial community analyses indicated that Paracoccus and Thauera ( Paracoccus - Thauera ), Desulfobulbus , and Syntrophomonas - Methanobacterium were the dominant taxa whose members catalyzed these three processes. Most-probable-number assays showed the presence of up to 10 7 /ml of propionate-oxidizing sulfate-reducing bacteria (SRB) in waters from the Medicine Hat Glauconitic C field. Bioreactors with the same concentrations of sulfate and VFA responded similarly to increasing concentrations of injected nitrate as observed in the microcosms: sulfide formation was prevented by adding approximately 80% of the nitrate dose needed to completely oxidize VFA to CO 2 in both. Thus, this work has demonstrated that simple time-dependent observations of the use of acetate, propionate, and butyrate for nitrate reduction, sulfate reduction, and methanogenesis in microcosms are a good proxy for these processes in bioreactors, monitoring of which is more complex. IMPORTANCE Oil field volatile fatty acids acetate, propionate, and butyrate were specifically used for nitrate reduction, sulfate reduction, and methanogenic fermentation. Time-dependent analyses of microcosms served as a good proxy for these processes in a bioreactor, mimicking a sulfide-producing (souring) oil reservoir: 80% of the nitrate dose required to oxidize volatile fatty acids to CO 2 was needed to prevent souring in both. Our data also suggest that propionate is a good substrate to enumerate oil field SRB. Copyright © 2017 American Society for Microbiology.

Load monitoring using a calibrated piezo diaphragm based impedance strain sensor and wireless sensor network in real time

NASA Astrophysics Data System (ADS)

Gopal Madhav Annamdas, Venu; Kiong Soh, Chee

2017-04-01

The last decade has seen the use of various wired-wireless and contact-contactless sensors in several structural health monitoring (SHM) techniques. Most SHM sensors that are predominantly used for strain measurements may be ineffective for damage detection and vice versa, indicating the uniapplicability of these sensors. However, piezoelectric (PE)-based macro fiber composite (MFC) and lead zirconium titanate (PZT) sensors have been on the rise in SHM, vibration and damping control, etc, due to their superior actuation and sensing abilities. These PE sensors have created much interest for their multi-applicability in various technologies such as electromechanical impedance (EMI)-based SHM. This research employs piezo diaphragms, a cheaper alternative to several expensive types of PZT/MFC sensors for the EMI technique. These piezo diaphragms were validated last year for their applicability in damage detection using the frequency domain. Here we further validate their applicability in strain monitoring using the real time domain. Hence, these piezo diaphragms can now be classified as PE sensors and used with PZT and MFC sensors in the EMI technique for monitoring damage and loading. However, no single technique or single type of sensor will be sufficient for large SHM, thus requiring the necessary deployment of more than one technique with different types of sensors such as a piezoresistive strain gauge based wireless sensor network for strain measurements to complement the EMI technique. Furthermore, we present a novel procedure of converting a regular PE sensor in the ‘frequency domain’ to ‘real time domain’ for strain applications.

Fundamental concepts of integrated and fiber optic sensors

NASA Technical Reports Server (NTRS)

Tuma, Margaret L.

1995-01-01

This chapter discusses fiber optic and integrated optic sensor concepts. Unfortunately, there is no standard method to categorize these sensor concepts. Here, fiber optic and integrated optic sensor concepts will be categorized by the primary modulation technique. These modulation techniques have been classified as: intensity, phase, wavelength, polarization, and time/frequency modulation. All modulate the output light with respect to changes in the physical or chemical property to be measured. Each primary modulation technique is then divided into fiber optic and integrated optic sections which are treated independently. For each sensor concept, possible sensor applications are discussed. The sensors and references discussed are not exhaustive, but sufficient to give the reader an overview of sensor concepts developed to date. Sensor multiplexing techniques such as wavelength division, time division, and frequency division will not be discussed as they are beyond the scope of this report.

Measurement of non-enteric emission fluxes of volatile fatty acids from a California dairy by solid phase micro-extraction with gas chromatography/mass spectrometry

NASA Astrophysics Data System (ADS)

Alanis, Phillip; Sorenson, Mark; Beene, Matt; Krauter, Charles; Shamp, Brian; Hasson, Alam S.

Dairies are a major source of volatile organic compounds (VOCs) in California's San Joaquin Valley; a region that experiences high ozone levels during summer. Short-chain carboxylic acids, or volatile fatty acids (VFAs), are believed to make up a large fraction of VOC emissions from these facilities, although there are few studies to substantiate this. In this work, a method using a flux chamber coupled to solid phase micro-extraction (SPME) fibers followed by analysis using gas chromatography/mass spectrometry was developed to quantify emissions of six VFAs (acetic acid, propanoic acid, butanoic acid, pentanoic acid, hexanoic acid and 3-methyl butanoic acid) from non-enteric sources. The technique was then used to quantify VFA fluxes from a small dairy located on the campus of California State University Fresno. Both animal feed and animal waste are found to be major sources of VFAs, with acetic acid contributing 70-90% of emissions from the sources tested. Measured total acid fluxes during spring (with an average temperature of 20 °C) were 1.84 ± 0.01, 1.06 ± 0.08, (1.3 ± 0.5) × 10 -2, (1.7 ± 0.2) × 10 -2 and (1.2 ± 0.5) × 10 -2 g m -2 h -1 from silage, total mixed rations, flushing lane, open lot and lagoon sources, respectively. VFA emissions from the sources tested total 390 ± 80 g h -1. The data indicate high fluxes of VFAs from dairy facilities, but differences in the design and operation of dairies in the San Joaquin Valley as well as seasonal variations mean that additional measurements must be made to accurately determine emissions inventories for the region.

Technical note: A device for obtaining time-integrated samples of ruminal fluid

USGS Publications Warehouse

Corley, R. N.; Murphy, M.R.; Lucena, J.; Panno, S.V.

1999-01-01

A device was adapted to allow for time-integrated sampling of fluid from the rumen via a cannula. The sampler consisted of a cup-shaped ceramic filter positioned in the ventral rumen of a cannulated cow and attached to a tube through which fluid entering the filter was removed continuously using a peristaltic pump. Rate of ruminal fluid removal using the device was monitored over two 36-h periods (at 6-h intervals) and was not affected (P > .05) by time, indicating that the system was not susceptible to clogging during this period. Two cows having ad libitum access to a totally mixed ration were used in a split-block design to evaluate the utility of the system for obtaining time-integrated samples of ruminal fluid. Ruminal fluid VFA concentration and pattern in samples collected in two replicated 8-h periods by the time-integrated sampler (at 1-h intervals) were compared with composite samples collected using a conventional suction-strainer device (at 30-min intervals). Each 8-h collection period started 2 h before or 6 h after feeding. Results indicated that total VFA concentration was not affected (P > .05) by the sampling method. Volatile fatty acid patterns were likewise unaffected (P > .05) except that acetate was 2.5% higher (P < .05) in samples collected 2 h before feeding and valerate was 5% higher (P < .05) in samples collected 6 h after feeding by the suction-strainer device. Although significant, these differences were not considered physiologically important. We concluded that use of the ceramic filter improved the sampling of ruminal fluid by simplifying the technique and allowing time-integrated samples to be obtained.

A comparison of force sensing techniques for planetary manipulation

NASA Technical Reports Server (NTRS)

Helmick, Daniel; Okon, Avi; DiCicco, Matt

2006-01-01

Five techniques for sensing forces with a manipulator are compared analytically and experimentally. The techniques compared are: a six-axis wrist force/torque sensor, joint torque sensors, link strain gauges, motor current sensors, and flexibility modeling. The accuracy and repeatability fo each technique is quantified and compared.

Optimization of volatile fatty acid production with co-substrate of food wastes and dewatered excess sludge using response surface methodology.

PubMed

Hong, Chen; Haiyun, Wu

2010-07-01

Central-composite design (CCD) and response surface methodology (RSM) were used to optimize the parameters of volatile fatty acid (VFA) production from food wastes and dewatered excess sludge in a semi-continuous process. The effects of four variables (food wastes composition in the co-substrate of food wastes and excess sludge, hydraulic retention time (HRT), organic loading rate (OLR), and pH) on acidogenesis were evaluated individually and interactively. The optimum condition derived via RSM was food wastes composition, 88.03%; HRT, 8.92 days; OLR, 8.31 g VSS/ld; and pH 6.99. The experimental VFA concentration was 29,099 mg/l under this optimum condition, which was well in agreement with the predicted value of 28,000 mg/l. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Application of Methanobrevibacter acididurans in anaerobic digestion.

PubMed

Savant, D V; Ranade, D R

2004-01-01

To operate anaerobic digesters successfully under acidic conditions, hydrogen utilizing methanogens which can grow efficiently at low pH and tolerate high volatile fatty acids (VFA) are desirable. An acid tolerant hydrogenotrophic methanogen viz. Methanobrevibacter acididurans isolated from slurry of an anaerobic digester running on alcohol distillery wastewater has been described earlier by this lab. This organism could grow optimally at pH 6.0. In the experiments reported herein, M. acididurans showed better methanogenesis under acidic conditions with high VFA, particularly acetate, than Methanobacterium bryantii, a common hydrogenotrophic inhabitant of anaerobic digesters. Addition of M. acididurans culture to digesting slurry of acidogenic as well as methanogenic digesters running on distillery wastewater showed increase in methane production and decrease in accumulation of volatile fatty acids. The results proved the feasibility of application of M. acididurans in anaerobic digesters.

Evolution of composition of dairy manure supernatant in a controlled dung pit.

PubMed

Rico, C; García, H; Rico, J L; Fernández, J; Renedo, J

2009-12-01

Anaerobic conversion of dairy manure into biogas is an attractive way of managing this waste. It is well known that the hydrolysis of large molecules into small, directly biodegradable ones is the rate limiting step of the overall anaerobic process. The present work studies the development of the hydrolytic and acidogenic stages of dairy manure with different solid concentrations (40, 60 and 80 g VS/L) at ambient temperature (20 degrees C). The purpose was to determine the operational conditions that provide a liquid fraction with a high soluble chemical oxygen demand (COD) and a high volatile fatty acids (VFA) content in manure before the methanogenic stage starts up. At 20 degrees C, the evolution of the studied parameters showed that, in a controlled plug-flow dung pit, the hydrolytic and acidogenic stages progressed moderately in a continuous way during the 25 days that the experimentation lasted, whereas no methanization was observed. Supernatant COD and VFA concentrations increased 30% and 107%, respectively, for the 60 g VS/L samples. Manure was also operated at 35 degrees C with a similar increase in supernatant COD but a higher increase in VFA, 154%. For both operational temperatures, the predominant VFAs were, in this order, acetic, propionic and butyric acids. During the operation at 35 degrees C, the methanogenic stage started between days 20 and 25 for the samples with lower solids content, i.e. 40 and 60 g VS/L.

Anaerobic co-digestion of food waste and landfill leachate in single-phase batch reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, Xiaofeng; Zhu, Shuangyan; Zhong, Delai

Highlights: • Anaerobic co-digestion strategy for food waste treatment at OLR 41.8 g VS/L. • A certain amount of raw leachate effectively relieved acidic inhibition. • The study showed that food waste was completely degraded. - Abstract: In order to investigate the effect of raw leachate on anaerobic digestion of food waste, co-digestions of food waste with raw leachate were carried out. A series of single-phase batch mesophilic (35 ± 1 °C) anaerobic digestions were performed at a food waste concentration of 41.8 g VS/L. The results showed that inhibition of biogas production by volatile fatty acids (VFA) occurred withoutmore » raw leachate addition. A certain amount of raw leachate in the reactors effectively relieved acidic inhibition caused by VFA accumulation, and the system maintained stable with methane yield of 369–466 mL/g VS. Total ammonia nitrogen introduced into the digestion systems with initial 2000–3000 mgNH{sub 4}–N/L not only replenished nitrogen for bacterial growth, but also formed a buffer system with VFA to maintain a delicate biochemical balance between the acidogenic and methanogenic microorganisms. UV spectroscopy and fluorescence excitation–emission matrix spectroscopy data showed that food waste was completely degraded. We concluded that using raw leachate for supplement water addition and pH modifier on anaerobic digestion of food waste was effective. An appropriate fraction of leachate could stimulate methanogenic activity and enhance biogas production.« less

Significance of measuring oxidative stress in lifestyle-related diseases from the viewpoint of correlation between d-ROMs and BAP in Japanese subjects.

PubMed

Fukui, Toshiki; Yamauchi, Kazuhiro; Maruyama, Mie; Yasuda, Tadashi; Kohno, Masakazu; Abe, Youichi

2011-09-01

In recent years, oxidative stress has been postulated to be an important factor in the pathogenesis and development of lifestyle-related diseases. In this study, we investigated the association between the derivatives of reactive oxygen metabolites (d-ROMs), as an index of products of reactive oxygen species (ROS), and biological antioxidant potential (BAP), as an index of antioxidant potential. We also investigated the associations between d-ROMs or BAP and the risk factors for lifestyle-related diseases or metabolic syndrome-associated factors to evaluate their usefulness in preventive medicine. There were 442 subjects who underwent health checkup examination in our facilities. In addition to standard medical checkup items, we analyzed d-ROMs, BAP, brachial-ankle pulse wave velocity, high-sensitivity C-reactive protein level and visceral fat area (VFA) visualized on a computed tomography scan. The mean d-ROM value in females was significantly higher than that in males. There was a positive correlation between the d-ROM and VFA levels. On correlation analysis, there was a negative correlation between the d-ROM and creatinine levels. As factors that influence d-ROMs, the level of VFA was selected, suggesting the significance of oxidative stress measurement with d-ROMs. In addition, there was a positive correlation between d-ROMs and BAP values. Further research is required to resolve whether increased production of ROS or the antioxidant potential that can compensate for such an increase of ROS is more important in vivo.

Applying a deep learning based CAD scheme to segment and quantify visceral and subcutaneous fat areas from CT images

NASA Astrophysics Data System (ADS)

Wang, Yunzhi; Qiu, Yuchen; Thai, Theresa; Moore, Kathleen; Liu, Hong; Zheng, Bin

2017-03-01

Abdominal obesity is strongly associated with a number of diseases and accurately assessment of subtypes of adipose tissue volume plays a significant role in predicting disease risk, diagnosis and prognosis. The objective of this study is to develop and evaluate a new computer-aided detection (CAD) scheme based on deep learning models to automatically segment subcutaneous fat areas (SFA) and visceral (VFA) fat areas depicting on CT images. A dataset involving CT images from 40 patients were retrospectively collected and equally divided into two independent groups (i.e. training and testing group). The new CAD scheme consisted of two sequential convolutional neural networks (CNNs) namely, Selection-CNN and Segmentation-CNN. Selection-CNN was trained using 2,240 CT slices to automatically select CT slices belonging to abdomen areas and SegmentationCNN was trained using 84,000 fat-pixel patches to classify fat-pixels as belonging to SFA or VFA. Then, data from the testing group was used to evaluate the performance of the optimized CAD scheme. Comparing to manually labelled results, the classification accuracy of CT slices selection generated by Selection-CNN yielded 95.8%, while the accuracy of fat pixel segmentation using Segmentation-CNN yielded 96.8%. Therefore, this study demonstrated the feasibility of using deep learning based CAD scheme to recognize human abdominal section from CT scans and segment SFA and VFA from CT slices with high agreement compared with subjective segmentation results.

In vitro Study of Noni Juice Extract Waste (Morinda citrifolia L.) and Pineapple Industrial Wastes (Ananas comosus L. Merr) as Energy Supplement in Dairy Goat Ration

NASA Astrophysics Data System (ADS)

Evvyernie, D.; Tjakradidjaja, A. S.; Permana, I. G.; Toharmat, T.; Insani, A.

2018-02-01

The aim of the study was to evaluate the potency of noni juice extract waste (Morinda citrifolia L.) and pineapple industrial wastes (Ananas comosus L. Merr) as an energy supplement in dairy goat ration through in vitro study. This study used a complete randomized design with 5 treatments and 3 rumen fluid groups. The treatments were R0 as control (60% Napier grass (NG) + 40% concentrate), R1 (45% NG + 15% noni juice extract waste + 40% concentrate) + R2 (45% NG + 15% noni juice extract waste ammoniated + 40% concentrate), R3 (45% NG + 15% pineapple peel + 40% concentrate), and R4 (45% NG + 15% pineapple crown + 40% concentrate). The variables were totalbacterial population, protozoal population, fermentation characteristic (total VFA and NH3 concentration), and digestibility (dry matter and organic matter).Data were analyzed with analysis of variance (ANOVA) and differences among treatments were determined by orthogonal contrast.The results showed that total VFA concentration was significant increased (P<0.05) by replacing 25% napier grass with noni juice extract waste (R1)or very significant increased(P<0.01) by replacing the grass with pineapple peel (R3). The average increasing of total VFA concentration was 74% compared to control. As conclusions, 15% pineapple peel or 15% noni juice extract waste can use as an energy supplement by replacing 25% of napier grass in lactating dairy goat ration.

A Survey on Optimal Signal Processing Techniques Applied to Improve the Performance of Mechanical Sensors in Automotive Applications

PubMed Central

Hernandez, Wilmar

2007-01-01

In this paper a survey on recent applications of optimal signal processing techniques to improve the performance of mechanical sensors is made. Here, a comparison between classical filters and optimal filters for automotive sensors is made, and the current state of the art of the application of robust and optimal control and signal processing techniques to the design of the intelligent (or smart) sensors that today's cars need is presented through several experimental results that show that the fusion of intelligent sensors and optimal signal processing techniques is the clear way to go. However, the switch between the traditional methods of designing automotive sensors and the new ones cannot be done overnight because there are some open research issues that have to be solved. This paper draws attention to one of the open research issues and tries to arouse researcher's interest in the fusion of intelligent sensors and optimal signal processing techniques.

Effect of cellobiose supplementation and dietary soluble fibre content on in vitro caecal fermentation of carbohydrate-rich substrates in rabbits.

PubMed

Ocasio-Vega, César; Abad-Guamán, Rodrigo; Delgado, Rebeca; Carabaño, Rosa; Carro, María Dolores; García, Javier

2018-06-01

The in vitro caecal fermentation of five substrates low in starch and protein content [d-(+)-glucose (GLU), d-cellobiose (CEL), sugar beet pectin (PEC), sugar beet pulp (SBP) and wheat straw (WS)] was investigated using soft faeces from rabbits receiving different levels of cellobiose and soluble fibre as inoculum. A total of 24 rabbits were supplemented 3 levels of cellobiose in the drinking water (0.0, 7.5, 15.0 g/l) and fed two experimental diets containing either low soluble fibre (LSF) or high soluble fibre (HSF) levels (84.0 and 130 g/kg dry matter). All substrates were subjected to a two-step pepsin/pancreatin in vitro pre-digestion, and the whole residue was used as substrate for the in vitro incubations. Gas production was measured until 144 h, and volatile fatty acid (VFA) production was determined at 24 h incubation. Experimental treatments did not affect SBP fermentation and had only a subtle influence on fermentation of WS and GLU. In contrast, cellobiose supplementation × donors' diet interactions were detected for most gas production parameters for CEL. Both the fractional gas production (k) and maximal gas production rates were linearly increased (p ≤ 0.042) and the initial delay in the onset of gas production (Lag) linearly decreased (p < 0.001) by cellobiose supplementation with the HSF inoculum, with no differences between the 7.5 and 15.0 doses. In contrast, with the LSF inoculum cellobiose supplementation only affected k values, which were quadratically increased (p = 0.043) and had maximal values for the 7.5 dose. A quadratic effect (p ≤ 0.018) of cellobiose supplementation was observed for total VFA production at 24 h when CEL and PEC were fermented, obtaining the maximal VFA production for the 7.5 dose of cellobiose. Total VFA production for CEL was greater with LSF than with HSF inoculum (20.7 vs. 12.9 mmol/l; p = 0.014), but the opposite was found for WS (3.97 vs. 6.21 mmol/l; p = 0.005). The use of LSF inoculum for CEL fermentation sharply reduced acetate (p = 0.001) and increased butyrate proportions (p ≤ 0.001) compared with the HSF inoculum. A positive relationship between total VFA caecal concentrations in rabbits receiving the same experimental treatments and in vitro values was only observed when WS was used as substrate (r = 0.90; p = 0.015; n = 6). The results suggest that experimental factors influenced the fermentative activity of caecal digesta, but the observed response differed with the incubated substrate, being the CEL the most affected.

Fiber optic sensors; Proceedings of the Meeting, Cannes, France, November 26, 27, 1985

NASA Technical Reports Server (NTRS)

Arditty, Herve J. (Editor); Jeunhomme, Luc B. (Editor)

1986-01-01

The conference presents papers on distributed sensors and sensor networks, signal processing and detection techniques, temperature measurements, chemical sensors, and the measurement of pressure, strain, and displacements. Particular attention is given to optical fiber distributed sensors and sensor networks, tactile sensing in robotics using an optical network and Z-plane techniques, and a spontaneous Raman temperature sensor. Other topics include coherence in optical fiber gyroscopes, a high bandwidth two-phase flow void fraction fiber optic sensor, and a fiber-optic dark-field microbend sensor.

Anaerobic Codigestion of Sludge: Addition of Butcher's Fat Waste as a Cosubstrate for Increasing Biogas Production.

PubMed

Martínez, E J; Gil, M V; Fernandez, C; Rosas, J G; Gómez, X

2016-01-01

Fat waste discarded from butcheries was used as a cosubstrate in the anaerobic codigestion of sewage sludge (SS). The process was evaluated under mesophilic and thermophilic conditions. The codigestion was successfully attained despite some inhibitory stages initially present that had their origin in the accumulation of volatile fatty acids (VFA) and adsorption of long-chain fatty acids (LCFA). The addition of a fat waste improved digestion stability and increased biogas yields thanks to the higher organic loading rate (OLR) applied to the reactors. However, thermophilic digestion was characterized by an effluent of poor quality and high VFA content. Results from spectroscopic analysis suggested the adsorption of lipid components onto the anaerobic biomass, thus disturbing the complete degradation of substrate during the treatment. The formation of fatty aggregates in the thermophilic reactor prevented process failure by avoiding the exposure of biomass to the toxic effect of high LCFA concentrations.

Anaerobic degradation of coconut husk leachate using UASB-reactor.

PubMed

Neena, C; Ambily, P S; Jisha, M S

2007-07-01

Reffing of coconut husk, the majorprocess in quality coir fibre extraction, causes serious pollution with brackish water lagoons of Kerala. An attempt is made to treat the coconut husk leachate by using a laboratory scale UASB-reactor The experiment was conducted with loading of leachate from 1 kg of fresh coconut husk. The anaerobic treatment was done continuously The parameters like VFA, pH, COD and polyphenols were analysed regularly during the evaluation of the reactor performance. The polyphenol, VFA and COD were diminished gradually with time. The pH of the reactor during the study was found to be in the range of 6-8. The biogas production was increased with loading and about 82% of the total COD/kg husk could be converted to biogas. The maximum polyphenol loading in the reactor was reached to about 298.51 mg/l of husk.

Fluorescence-based monitoring of tracer and substrate distribution in an UASB reactor.

PubMed

Lou, S J; Tartakovsky, B; Zeng, Y; Wu, P; Guiot, S R

2006-11-01

In this work, rhodamine-related fluorescence was measured on-line at four reactor heights in order to study hydrodynamics within an upflow anaerobic sludge bed reactor. A linear dependence of the dispersion coefficient (D) on the upflow velocity was observed, while the influence of the organic loading rate (OLR) was insignificant. Furthermore, the Bodenstein number of the reactor loaded with granulated sludge was found to be position-dependent with the largest values measured at the bottom of the sludge bed. This trend was not observed in the reactor without sludge. Chemical oxygen demand (COD) and volatile fatty acid (VFA) concentrations were measured at the same reactor heights as in rhodamine tests using conventional off-line analytical methods and on-line multiwavelength fluorometry. Significant spatial COD and VFA gradients were observed at organic loading rates above 6g COD l(R)(-1)d(-1) and linear upflow velocities below 0.8m h(-1).

Biological upgrading of volatile fatty acids, key intermediates for the valorization of biowaste through dark anaerobic fermentation.

PubMed

Singhania, Reeta Rani; Patel, Anil Kumar; Christophe, Gwendoline; Fontanille, Pierre; Larroche, Christian

2013-10-01

VFAs can be obtained from lignocellulosic agro-industrial wastes, sludge, and various biodegradable organic wastes as key intermediates through dark fermentation processes and synthesized through chemical route also. They are building blocks of several organic compounds viz. alcohol, aldehyde, ketones, esters and olefins. These can serve as alternate carbon source for microbial biolipid, biohydrogen, microbial fuel cells productions, methanisation, and for denitrification. Organic wastes are the substrate for VFA platform that is of zero or even negative cost, giving VFA as intermediate product but their separation from the fermentation broth is still a challenge; however, several separation technologies have been developed, membrane separation being the most suitable one. These aspects will be reviewed and results obtained during anaerobic treatment of slaughterhouse wastes with further utilisation of volatile fatty acids for yeast cultivation have been discussed. Copyright © 2012 Elsevier Ltd. All rights reserved.

Anaerobic Codigestion of Sludge: Addition of Butcher’s Fat Waste as a Cosubstrate for Increasing Biogas Production

PubMed Central

Martínez, E. J.; Gil, M. V.; Fernandez, C.; Rosas, J. G.

2016-01-01

Fat waste discarded from butcheries was used as a cosubstrate in the anaerobic codigestion of sewage sludge (SS). The process was evaluated under mesophilic and thermophilic conditions. The codigestion was successfully attained despite some inhibitory stages initially present that had their origin in the accumulation of volatile fatty acids (VFA) and adsorption of long-chain fatty acids (LCFA). The addition of a fat waste improved digestion stability and increased biogas yields thanks to the higher organic loading rate (OLR) applied to the reactors. However, thermophilic digestion was characterized by an effluent of poor quality and high VFA content. Results from spectroscopic analysis suggested the adsorption of lipid components onto the anaerobic biomass, thus disturbing the complete degradation of substrate during the treatment. The formation of fatty aggregates in the thermophilic reactor prevented process failure by avoiding the exposure of biomass to the toxic effect of high LCFA concentrations. PMID:27071074

New approach to control the methanogenic reactor of a two-phase anaerobic digestion system.

PubMed

von Sachs, Jürgen; Meyer, Ulrich; Rys, Paul; Feitkenhauer, Heiko

2003-03-01

A new control strategy for the methanogenic reactor of a two-phase anaerobic digestion system has been developed and successfully tested on the laboratory scale. The control strategy serves the purpose to detect inhibitory effects and to achieve good conversion. The concept is based on the idea that volatile fatty acids (VFA) can be measured in the influent of the methanogenic reactor by means of titration. Thus, information on the output (methane production) and input of the methanogenic reactor is available, and a (carbon) mass balance can be obtained. The control algorithm comprises a proportional/integral structure with the ratio of (a) the methane production rate measured online and (b) a maximum methane production rate expected (derived from the stoichiometry) as a control variable. The manipulated variable is the volumetric feed rate. Results are shown for an experiment with VFA (feed) concentration ramps and for experiments with sodium chloride as inhibitor.

Stimulation of the anaerobic digestion of the dry organic fraction of municipal solid waste (OFMSW) with carbon-based conductive materials.

PubMed

Dang, Yan; Sun, Dezhi; Woodard, Trevor L; Wang, Li-Ying; Nevin, Kelly P; Holmes, Dawn E

2017-08-01

Growth of bacterial and archaeal species capable of interspecies electron exchange was stimulated by addition of conductive materials (carbon cloth or granular activated carbon (GAC)) to anaerobic digesters treating dog food (a substitute for the dry-organic fraction of municipal solid waste (OFMSW)). Methane production (772-1428mmol vs <80mmol), volatile solids removal (78%-81% vs 54%-64%) and COD removal efficiencies (∼80% vs 20%-30%) were all significantly higher in reactors amended with GAC or carbon cloth than controls. OFMSW degradation was also significantly accelerated and VFA concentrations were substantially lower in reactors amended with conductive materials. These results suggest that both conductive materials (carbon cloth and GAC) can promote conversion of OFMSW to methane even in the presence of extremely high VFA concentrations (∼500mM). Copyright © 2017 Elsevier Ltd. All rights reserved.

Multi-phased anaerobic baffled reactor treating food waste.

PubMed

Ahamed, A; Chen, C-L; Rajagopal, R; Wu, D; Mao, Y; Ho, I J R; Lim, J W; Wang, J-Y

2015-04-01

This study was conducted to identify the performance of a multi-phased anaerobic baffled reactor (MP-ABR) with food waste (FW) as the substrate for biogas production and thereby to promote an efficient energy recovery and treatment method for the wastes with high organic solid content through phase separation. A four-chambered ABR was operated at an HRT of 30 days with an OLR of 0.5-1.0 g-VS/Ld for a period of 175 days at 35 ± 1°C. Consistent overall removal efficiencies of 85.3% (CODt), 94.5% (CODs), 89.6% (VFA) and 86.4% (VS) were observed throughout the experiment displaying a great potential to treat FW. Biogas generated was 215.57 mL/g-VS removed d. Phase separation was observed and supported by the COD and VFA trends, and an efficient recovery of bioenergy from FW was achieved. Copyright © 2015 Elsevier Ltd. All rights reserved.

Application of zonal model on indoor air sensor network design

NASA Astrophysics Data System (ADS)

Chen, Y. Lisa; Wen, Jin

2007-04-01

Growing concerns over the safety of the indoor environment have made the use of sensors ubiquitous. Sensors that detect chemical and biological warfare agents can offer early warning of dangerous contaminants. However, current sensor system design is more informed by intuition and experience rather by systematic design. To develop a sensor system design methodology, a proper indoor airflow modeling approach is needed. Various indoor airflow modeling techniques, from complicated computational fluid dynamics approaches to simplified multi-zone approaches, exist in the literature. In this study, the effects of two airflow modeling techniques, multi-zone modeling technique and zonal modeling technique, on indoor air protection sensor system design are discussed. Common building attack scenarios, using a typical CBW agent, are simulated. Both multi-zone and zonal models are used to predict airflows and contaminant dispersion. Genetic Algorithm is then applied to optimize the sensor location and quantity. Differences in the sensor system design resulting from the two airflow models are discussed for a typical office environment and a large hall environment.

Loss-compensation technique using a split-spectrum approach for optical fiber air-gap intensity-based sensors

NASA Astrophysics Data System (ADS)

Wang, Anbo; Miller, Mark S.; Gunther, Michael F.; Murphy, Kent A.; Claus, Richard O.

1993-03-01

A self-referencing technique compensating for fiber losses and source fluctuations in air-gap intensity-based optical fiber sensors is described and demonstrated. A resolution of 0.007 micron has been obtained over a measurement range of 0-250 microns for an intensity-based displacement sensor using this referencing technique. The sensor is shown to have minimal sensitivity to fiber bending losses and variations in the LED input power. A theoretical model for evaluation of step-index multimode optical fiber splice is proposed. The performance of the sensor as a displacement sensor agrees well with the theoretical analysis.

A novel process for volatile fatty acids production from syngas by integrating with mesophilic alkaline fermentation of waste activated sludge.

PubMed

Rao, Yue; Wan, Jingjing; Liu, Yafeng; Angelidaki, Irini; Zhang, Shicheng; Zhang, Yalei; Luo, Gang

2018-08-01

The present study proposed and demonstrated a novel process for the bioconversion of syngas (mainly CO and H 2 ) to valuable volatile fatty acids (VFA) by integrating with mesophilic alkaline fermentation of waste activated sludge (WAS). The results showed that although pH 9 was suitable for VFA production from WAS, 62.5% of the consumed CO was converted to methane due to the presence of hydrogenogenic pathway for CO conversion. The increase of pH from 9 to 9.5 inhibited the methane production from CO because of the possible presence of only acetogenic pathway for CO conversion. However, methane was still produced from H 2 contained in syngas through hydrogenotrophic methanogenesis, and around 32-34% of the consumed syngas was converted to methane. At both pH 9 and 9.5, methane was produced by hydrogenotrophic methanogens Methanobacteriales. Further increase of pH to 10 effectively inhibited methane production from syngas, and efficient VFA (mainly acetate with the concentration of around 135 mM) production by simultaneous conversion of syngas and WAS was achieved. High acetate concentrations (>150 mM) were shown to have serious negative effects on the conversion of syngas. The addition of syngas to the mesophilic alkaline fermentation of WAS at pH 10 not only resulted in the enrichment of some known bacteria related with syngas conversion, but also changed the microbial community compositions for the fermentation of WAS. Copyright © 2018 Elsevier Ltd. All rights reserved.

The gas chromatographic determination of volatile fatty acids in wastewater samples: evaluation of experimental biases in direct injection method against thermal desorption method.

PubMed

Ullah, Md Ahsan; Kim, Ki-Hyun; Szulejko, Jan E; Cho, Jinwoo

2014-04-11

The production of short-chained volatile fatty acids (VFAs) by the anaerobic bacterial digestion of sewage (wastewater) affords an excellent opportunity to alternative greener viable bio-energy fuels (i.e., microbial fuel cell). VFAs in wastewater (sewage) samples are commonly quantified through direct injection (DI) into a gas chromatograph with a flame ionization detector (GC-FID). In this study, the reliability of VFA analysis by the DI-GC method has been examined against a thermal desorption (TD-GC) method. The results indicate that the VFA concentrations determined from an aliquot from each wastewater sample by the DI-GC method were generally underestimated, e.g., reductions of 7% (acetic acid) to 93.4% (hexanoic acid) relative to the TD-GC method. The observed differences between the two methods suggest the possibly important role of the matrix effect to give rise to the negative biases in DI-GC analysis. To further explore this possibility, an ancillary experiment was performed to examine bias patterns of three DI-GC approaches. For instance, the results of the standard addition (SA) method confirm the definite role of matrix effect when analyzing wastewater samples by DI-GC. More importantly, their biases tend to increase systematically with increasing molecular weight and decreasing VFA concentrations. As such, the use of DI-GC method, if applied for the analysis of samples with a complicated matrix, needs a thorough validation to improve the reliability in data acquisition. Copyright © 2014 Elsevier B.V. All rights reserved.

The Concentrations of Rumen Fluid Volatile Fatty Acids and Ammonia, and Rumen Microbial Protein Production in Sheep Given Feed During the Day and Night Time

NASA Astrophysics Data System (ADS)

Gumilar, D. A. K. W.; Rianto, E.; Arifin, M.

2018-02-01

An experimental study was carried out to investigate the concentrations of volatile (VFA), ammonia and microbial protein production of rumen fluid in sheep given fedd during the day and at night. This study used 12 fat-tailed rams aged 12-18 months and weighed 24,12 ± 25 kg (CV = 10,51%). The rams were fed a complete feed containing 16.64% protein and 68,33% total digestible nutrients (TDN). The rams were allocated into a completely randomised design with 3 treatments and 4 replications. The treatments applied were: T1: day time feeding (6.00 hrs - 18.00 hrs); T2: night time feeding (18.00 hrs - 6.00 hrs); and T3: day and night time feedings (6.00 hrs - 6.00 hrs). The parameters observed were dry matter intake (DMI), rumen VFA concentration, rumen ammonia concentration, rumen rmicrobial protein production and the efficiency of rumen microbial protein production. The results showed that feeding time did not significantly affect (P>0.05) all the parameters observed. Dry matter intake, VFA concentration, ammonia concentration, the microbial protein production of rumen fluid and the efficiency of microbial protein production were 1,073g/d, 49.69 mmol; 4.77 mg N/100 ml, 12,111 g/d and 19.96 g per kg digestible organic matter intake (DOMI), respectively. It is concluded that feeding time did not affect DMI, condition of rumen fluid and rumen microbial protein production in sheep.

Color regeneration from reflective color sensor using an artificial intelligent technique.

PubMed

Saracoglu, Ömer Galip; Altural, Hayriye

2010-01-01

A low-cost optical sensor based on reflective color sensing is presented. Artificial neural network models are used to improve the color regeneration from the sensor signals. Analog voltages of the sensor are successfully converted to RGB colors. The artificial intelligent models presented in this work enable color regeneration from analog outputs of the color sensor. Besides, inverse modeling supported by an intelligent technique enables the sensor probe for use of a colorimetric sensor that relates color changes to analog voltages.

A near-optimal low complexity sensor fusion technique for accurate indoor localization based on ultrasound time of arrival measurements from low-quality sensors

NASA Astrophysics Data System (ADS)

Mitilineos, Stelios A.; Argyreas, Nick D.; Thomopoulos, Stelios C. A.

2009-05-01

A fusion-based localization technique for location-based services in indoor environments is introduced herein, based on ultrasound time-of-arrival measurements from multiple off-the-shelf range estimating sensors which are used in a market-available localization system. In-situ field measurements results indicated that the respective off-the-shelf system was unable to estimate position in most of the cases, while the underlying sensors are of low-quality and yield highly inaccurate range and position estimates. An extensive analysis is performed and a model of the sensor-performance characteristics is established. A low-complexity but accurate sensor fusion and localization technique is then developed, which consists inof evaluating multiple sensor measurements and selecting the one that is considered most-accurate based on the underlying sensor model. Optimality, in the sense of a genie selecting the optimum sensor, is subsequently evaluated and compared to the proposed technique. The experimental results indicate that the proposed fusion method exhibits near-optimal performance and, albeit being theoretically suboptimal, it largely overcomes most flaws of the underlying single-sensor system resulting in a localization system of increased accuracy, robustness and availability.

Instability diagnosis and syntrophic acetate oxidation during thermophilic digestion of vegetable waste.

PubMed

Li, Dong; Ran, Yi; Chen, Lin; Cao, Qin; Li, Zhidong; Liu, Xiaofeng

2018-08-01

Effective process monitoring and instability diagnosis are important for stable anaerobic digestion (AD) of vegetable waste (VW). In order to evaluate the performance of thermophilic digestion of VW, to make early diagnosis for instability after organic overload, and to reveal the dynamics of microbial community under different running states, thermophilic AD of VW was carried out under improved organic loading rates (OLR) of 0.5-2.5 g volatile solid (VS)/(L ∙ d) in this study. Gaseous parameters including volumetric methane production rate (VMPR), CH 4 , CO 2 , and H 2 concentrations, and liquid parameters including pH, oxidation-reduction potential, volatile fatty acid (VFA), and total alkalinity (TA), bicarbonate alkalinity (BA), intermediate alkalinity (IA), and ammonia, were monitored. The coupling parameters, such as the CH 4 /CO 2 , VFA/BA, and BA/TA ratios were also used to evaluate stability. The dynamics of syntrophic acetate-oxidizing bacteria (SAOB), acetoclastic methanogens (AM), and hydrogenotrophic methanogens (HM) were analyzed by high-throughput sequencing. The main methanogenic bacteria were HM (Methanothermobacter) during the start-up period of OLR 0.5 gVS/(L ∙ d), while they were AM (Methanosarcina) during the stable period of OLR of 1.0 gVS/(L ∙ d). The VMPR of stable period was about 0.29 L/(L · d) with total VFA concentration below 100 mg/L, CH 4 /CO 2  > 1.3, and BA/TA>0.9. The first instability due to the accumulation of VFA and self-recovery due to syntrophic acetate oxidation occurred at an OLR of 1.5 gVS/(L ∙ d). The syntrophic acetate-oxidizing bacteria probably belong to genus S1 (family Thermotogaceae). The digestion failed at an OLR of 2.0 g VS/(L · d). H 2 was only detected during collapsed period instead of instable period. The total ammonia nitrogen loss and bicarbonate alkalinity (BA) reduction were the primary causes for the instability of AD of VW without effluent recirculation. Compared with single parameters, the CH 4 /CO 2 and BA/total alkalinity (TA) ratios are recommended as early warning indicators for engineering applications of thermophilic AD of VW. Copyright © 2018 Elsevier Ltd. All rights reserved.

Flush Mounting Of Thin-Film Sensors

NASA Technical Reports Server (NTRS)

Moore, Thomas C., Sr.

1992-01-01

Technique developed for mounting thin-film sensors flush with surfaces like aerodynamic surfaces of aircraft, which often have compound curvatures. Sensor mounted in recess by use of vacuum pad and materials selected for specific application. Technique involves use of materials tailored to thermal properties of substrate in which sensor mounted. Together with customized materials, enables flush mounting of thin-film sensors in most situations in which recesses for sensors provided. Useful in both aircraft and automotive industries.

Sensor fusion III: 3-D perception and recognition; Proceedings of the Meeting, Boston, MA, Nov. 5-8, 1990

NASA Technical Reports Server (NTRS)

Schenker, Paul S. (Editor)

1991-01-01

The volume on data fusion from multiple sources discusses fusing multiple views, temporal analysis and 3D motion interpretation, sensor fusion and eye-to-hand coordination, and integration in human shape perception. Attention is given to surface reconstruction, statistical methods in sensor fusion, fusing sensor data with environmental knowledge, computational models for sensor fusion, and evaluation and selection of sensor fusion techniques. Topics addressed include the structure of a scene from two and three projections, optical flow techniques for moving target detection, tactical sensor-based exploration in a robotic environment, and the fusion of human and machine skills for remote robotic operations. Also discussed are K-nearest-neighbor concepts for sensor fusion, surface reconstruction with discontinuities, a sensor-knowledge-command fusion paradigm for man-machine systems, coordinating sensing and local navigation, and terrain map matching using multisensing techniques for applications to autonomous vehicle navigation.

Miscellaneous methods for measuring matric or water potential

USGS Publications Warehouse

Scanlon, Bridget R.; Andraski, Brian J.; Bilskie, Jim; Dane, Jacob H.; Topp, G. Clarke

2002-01-01

A variety of techniques to measure matric potential or water potential in the laboratory and in the field are described in this section. The techniques described herein require equilibration of some medium whose matric or water potential can be determined from previous calibration or can be measured directly. Under equilibrium conditions the matric or water potential of the medium is equal to that of the soil. The techniques can be divided into: (i) those that measure matric potential and (ii) those that measure water potential (sum of matric and osmotic potentials). Matric potential is determined when the sensor matrix is in direct contact with the soil, so salts are free to diffuse in or out of the sensor matrix, and the equilibrium measurement therefore reflects matric forces acting on the water. Water potential is determined when the sensor is separated from the soil by a vapor gap, so salts are not free to move in or out of the sensor, and the equilibrium measurement reflects the sum of the matric and osmotic forces acting on the water.Seven different techniques are described in this section. Those that measure matric potential include (i) heat dissipation sensors, (ii) electrical resistance sensors, (iii) frequency domain and time domain sensors, and (iv) electro-optical switches. A method that can be used to measure matric potential or water potential is the (v) filter paper method. Techniques that measure water potential include (vi) the Dew Point Potentiameter (Decagon Devices, Inc., Pullman, WA1) (water activity meter) and (vii) vapor equilibration.The first four techniques are electronically based methods for measuring matric potential. Heat dissipation sensors and electrical resistance sensors infer matric potential from previously determined calibration relations between sensor heat dissipation or electrical resistance and matric potential. Frequency-domain and timedomain matric potential sensors measure water content, which is related to matric potential of the sensor through calibration. Electro-optical switches measure changes in light transmission through thin, nylon filters as they absorb or desorb water in response to changes in matric potential. Heat dissipation sensors and electrical resistance sensors are used primarily in the field to provide information on matric potential. Frequency domain matric potential sensors are new and have not been widely used. Time domain matric potential sensors and electro-optical switches are new and have not been commercialized. For the fifth technique, filter paper is used as the standard matrix. The filter paper technique measures matric potential when the filter paper is in direct contact with soil or water potential when separated from soil by a vapor gap. The Dew Point Potentiameter calculates water potential from the measured dew point and sample temperature. The vapor equilibration technique involves equilibration of soil samples with salt solutions of known osmotic potential. The filter paper, Dew Point Potentiameter, and vapor equilibration techniques are generally used in the laboratory to measure water potential of disturbed field samples or to measure water potential for water retention functions.

Field Calibration of Wind Direction Sensor to the True North and Its Application to the Daegwanryung Wind Turbine Test Sites

PubMed Central

Lee, Jeong Wan

2008-01-01

This paper proposes a field calibration technique for aligning a wind direction sensor to the true north. The proposed technique uses the synchronized measurements of captured images by a camera, and the output voltage of a wind direction sensor. The true wind direction was evaluated through image processing techniques using the captured picture of the sensor with the least square sense. Then, the evaluated true value was compared with the measured output voltage of the sensor. This technique solves the discordance problem of the wind direction sensor in the process of installing meteorological mast. For this proposed technique, some uncertainty analyses are presented and the calibration accuracy is discussed. Finally, the proposed technique was applied to the real meteorological mast at the Daegwanryung test site, and the statistical analysis of the experimental testing estimated the values of stable misalignment and uncertainty level. In a strict sense, it is confirmed that the error range of the misalignment from the exact north could be expected to decrease within the credibility level. PMID:27873957

Coherent Pound-Drever-Hall technique for high resolution fiber optic strain sensor at very low light power

NASA Astrophysics Data System (ADS)

Wu, Mengxin; Liu, Qingwen; Chen, Jiageng; He, Zuyuan

2017-04-01

Pound-Drever-Hall (PDH) technique has been widely adopted for ultrahigh resolution fiber-optic sensors, but its performance degenerates seriously as the light power drops. To solve this problem, we developed a coherent PDH technique for weak optical signal detection, with which the signal-to-noise ratio (SNR) of demodulated PDH signal is dramatically improved. In the demonstrational experiments, a high resolution fiber-optic sensor using the proposed technique is realized, and n"-order strain resolution at a low light power down to -43 dBm is achieved, which is about 15 dB lower compared with classical PDH technique. The proposed coherent PDH technique has great potentials in longer distance and larger scale sensor networks.

Frontiers in Chemical Sensors: Novel Principles and Techniques

NASA Astrophysics Data System (ADS)

Orellana, Guillermo; Moreno-Bondi, Maria Cruz

This third volume of Springer Series on Chemical Sensors and Biosensors aims to enable the researcher or technologist to become acquainted with the latest principles and techniques that keep on enlarging the applications in this fascinating field. It deals with the novel luminescence lifetime-based techniques for interrogation of sensor arrays in high-throughput screening, cataluminescence, chemical sensing with hollow waveguides, new ways in sensor design and fabrication by means of either combinatorial methods or engineered indicator/support couples.

Estimating propagation velocity through a surface acoustic wave sensor

DOEpatents

Xu, Wenyuan; Huizinga, John S.

2010-03-16

Techniques are described for estimating the propagation velocity through a surface acoustic wave sensor. In particular, techniques which measure and exploit a proper segment of phase frequency response of the surface acoustic wave sensor are described for use as a basis of bacterial detection by the sensor. As described, use of velocity estimation based on a proper segment of phase frequency response has advantages over conventional techniques that use phase shift as the basis for detection.

Fiber Loop Ringdown — a Time-Domain Sensing Technique for Multi-Function Fiber Optic Sensor Platforms: Current Status and Design Perspectives

PubMed Central

Wang, Chuji

2009-01-01

Fiber loop ringdown (FLRD) utilizes an inexpensive telecommunications light source, a photodiode, and a section of single-mode fiber to form a uniform fiber optic sensor platform for sensing various quantities, such as pressure, temperature, strain, refractive index, chemical species, biological cells, and small volume of fluids. In FLRD, optical losses of a light pulse in a fiber loop induced by changes in a quantity are measured by the light decay time constants. FLRD measures time to detect a quantity; thus, FLRD is referred to as a time-domain sensing technique. FLRD sensors have near real-time response, multi-pass enhanced high-sensitivity, and relatively low cost (i.e., without using an optical spectral analyzer). During the last eight years since the introduction of the original form of fiber ringdown spectroscopy, there has been increasing interest in the FLRD technique in fiber optic sensor developments, and new application potential is being explored. This paper first discusses the challenging issues in development of multi-function, fiber optic sensors or sensor networks using current fiber optic sensor sensing schemes, and then gives a review on current fiber optic sensor development using FLRD technique. Finally, design perspectives on new generation, multi-function, fiber optic sensor platforms using FLRD technique are particularly presented. PMID:22408471

From Data Acquisition to Data Fusion: A Comprehensive Review and a Roadmap for the Identification of Activities of Daily Living Using Mobile Devices

PubMed Central

Pires, Ivan Miguel; Garcia, Nuno M.; Pombo, Nuno; Flórez-Revuelta, Francisco

2016-01-01

This paper focuses on the research on the state of the art for sensor fusion techniques, applied to the sensors embedded in mobile devices, as a means to help identify the mobile device user’s daily activities. Sensor data fusion techniques are used to consolidate the data collected from several sensors, increasing the reliability of the algorithms for the identification of the different activities. However, mobile devices have several constraints, e.g., low memory, low battery life and low processing power, and some data fusion techniques are not suited to this scenario. The main purpose of this paper is to present an overview of the state of the art to identify examples of sensor data fusion techniques that can be applied to the sensors available in mobile devices aiming to identify activities of daily living (ADLs). PMID:26848664

A Wearable Real-Time and Non-Invasive Thoracic Cavity Monitoring System

NASA Astrophysics Data System (ADS)

Salman, Safa

A surgery-free on-body monitoring system is proposed to evaluate the dielectric constant of internal body tissues (especially lung and heart) and effectively determine irregularities in real-time. The proposed surgery-free on-body monitoring system includes a sensor, a post-processing technique, and an automated data collection circuit. Data are automatically collected from the sensor electrodes and then post processed to extract the electrical properties of the underlying biological tissue(s). To demonstrate the imaging concept, planar and wrap-around sensors are devised. These sensors are designed to detect changes in the dielectric constant of inner tissues (lung and heart). The planar sensor focuses on a single organ while the wrap-around sensors allows for imaging of the thoracic cavity's cross section. Moreover, post-processing techniques are proposed to complement sensors for a more complete on-body monitoring system. The idea behind the post-processing technique is to suppress interference from the outer layers (skin, fat, muscle, and bone). The sensors and post-processing techniques yield high signal (from the inner layers) to noise (from the outer layers) ratio. Additionally, data collection circuits are proposed for a more robust and stand-alone system. The circuit design aims to sequentially activate each port of the sensor and portions of the propagating signal are to be received at all passive ports in the form of a voltage at the probes. The voltages are converted to scattering parameters which are then used in the post-processing technique to obtain epsilonr. The concept of wearability is also considered through the use of electrically conductive fibers (E-fibers). These fibers show matching performance to that of copper, especially at low frequencies making them a viable substitute. For the cases considered, the proposed sensors show promising results in recovering the permittivity of deep tissues with a maximum error of 13.5%. These sensors provide a way for a new class of medical sensors through accuracy improvements and avoidance of inverse scattering techniques.

Increased dipicolinic acid production with an enhanced spoVF operon in Bacillus subtilis and medium optimization.

PubMed

Takahashi, Fumikazu; Sumitomo, Nobuyuki; Hagihara, Hiroshi; Ozaki, Katsuya

2015-01-01

Dipicolinic acid (DPA) is a multi-functional agent for cosmetics, antimicrobial products, detergents, and functional polymers. The aim of this study was to design a new method for producing DPA from renewable material. The Bacillus subtilis spoVF operon encodes enzymes for DPA synthase and the part of lysine biosynthetic pathway. However, DPA is only synthesized in the sporulation phase, so the productivity of DPA is low level. Here, we report that DPA synthase was expressed in vegetative cells, and DPA was produced in the culture medium by replacement of the spoVFA promoter with other highly expressed promoter in B. subtilis vegetative cells, such as spoVG promoter. DPA levels were increased in the culture medium of genetically modified strains. DPA productivity was significantly improved up to 29.14 g/L in 72 h culture by improving the medium composition using a two-step optimization technique with the Taguchi methodology.

Rumen morphometrics and the effect of digesta pH and volume on volatile fatty acid absorption.

PubMed

Melo, L Q; Costa, S F; Lopes, F; Guerreiro, M C; Armentano, L E; Pereira, M N

2013-04-01

The effects of rumen digesta volume and pH on VFA absorption and its relation to rumen wall morphology were evaluated. Nine rumen cannulated cows formed 3 groups based on desired variation in rumen morphology: The High group was formed by Holsteins yielding 25.9 kg milk/d and fed on a high-grain total mixed ration (TMR); the Medium group by Holstein-Zebu crossbreds yielding 12.3 kg milk/d and fed on corn silage, tropical pasture, and a commercial concentrate; and the Dry group by nonlactating grazing Jerseys fed exclusively on tropical pasture. Within each group, a sequence of 3 ruminal conditions was induced on each cow in 3 × 3 Latin Squares, with 7-d periods: high digesta volume and high pH (HVHP), low volume and high pH (LVHP), and low volume and low pH (LVLP). Rumen mucosa was biopsied on the first day of Period 1. Ruminal morphometric variables evaluated were mitotic index, absorptive surface and papillae number per square centimeter of wall, area per papillae, papillae area as a percentage of absorptive surface, and epithelium, keratinized layer, and nonkeratinized layer thickness. There was marked variation in rumen morphology among the groups of cows. Grazing Jerseys had decreased rumen wall absorptive surface area and basal cells mitotic index, and increased thickness of the epithelium and of the keratin layer compared with cows receiving concentrates. Mean rumen pH throughout the 4 h sampling period was: 6.78 for HVHP, 7.08 for LVHP, and 5.90 for LVLP (P < 0.01). The capacity of the rumen wall to absorb VFA was estimated by the Valerate/CrEDTA technique. The fractional exponential decay rate for the ratio of valeric acid to Cr (k Val/Cr) was determined by rumen digesta sampling at 20-min intervals during 4 h, after the mixing of markers and the return of the evacuated ruminal content. The k Val/Cr values for treatments HVHP, LVHP, and LVLP were, respectively: 19.6, 23.9, and 35.0 %/h (SEM = 2.01; P = 0.21 for contrast HVHP vs. LVHP and P < 0.01 for contrast LVHP vs. LVLP). The k Val/Cr was faster under low pH, but decreasing digesta volume under high pH did not elicit such a response. The correlation between the absorptive surface area per square centimeter of rumen wall and the mean of the 3 k Val/Cr values of each cow was 0.90 (P < 0.01). Cows capable of maintaining a less-acidic rumen environment had greater inflow of water into the digestive cavity, had a more developed rumen mucosa, and were more efficient VFA absorbers.

Effects of bacterial direct-fed microbials on ruminal characteristics, methane emission, and milk fatty acid composition in cows fed high- or low-starch diets.

PubMed

Philippeau, C; Lettat, A; Martin, C; Silberberg, M; Morgavi, D P; Ferlay, A; Berger, C; Nozière, P

2017-04-01

This study investigated the effects of bacterial direct-fed microbials (DFM) on ruminal fermentation and microbial characteristics, methane (CH 4 ) emission, diet digestibility, and milk fatty acid (FA) composition in dairy cows fed diets formulated to induce different ruminal volatile fatty acid (VFA) profiles. Eight ruminally cannulated dairy cows were divided into 2 groups based on parity, days in milk, milk production, and body weight. Cows in each group were fed either a high-starch (38%, HS) or a low-starch (2%, LS) diet in a 55:45 forage-to-concentrate ratio on a dry matter (DM) basis. For each diet, cows were randomly assigned to 1 of 4 treatments in a Latin square design of (1) control (CON); (2) Propionibacterium P63 (P63); (3) P63 plus Lactobacillus plantarum 115 (P63+Lp); (4) P63 plus Lactobacillus rhamnosus 32 (P63+Lr). Strains of DFM were administered at 10 10 cfu/d. Methane emission (using the sulfur hexafluoride tracer technique), total-tract digestibility, dry matter intake, and milk production and composition were quantified in wk 3. Ruminal fermentation and microbial characteristics were measured in wk 4. Data were analyzed using the mixed procedure of SAS (SAS Institute Inc., Cary, NC). The 2 diets induced different ruminal VFA profiles, with a greater proportion of propionate at the expense of acetate and butyrate for the HS diet. Greater concentrations of total bacteria and selected bacterial species of methanogenic Archaea were reported for the HS diet, whereas the protozoa concentration in HS decreased. For both diets, bacterial DFM supplementation raised ruminal pH (+0.18 pH units, on average) compared with CON. Irrespective of diet, P63+Lp and P63+Lr increased ruminal cellulase activity (3.8-fold, on average) compared with CON, but this effect was not associated with variations in ruminal microbial numbers. Irrespective of diet, no effect of bacterial DFM on ruminal VFA was observed. For the LS diet, supplementing cows with P63+Lr tended to decrease CH 4 emission (26.5%, on average, when expressed per kilogram of milk or 4% fat-corrected milk). Only P63 supplementation to cows fed the HS diet affected the concentration of some milk FA, such as cis isomers of 18:1 and intermediates of ruminal biohydrogenation of polyunsaturated FA. Overall, bacterial DFM could be useful to stabilize ruminal pH. Their effects on CH 4 production mitigation and milk FA profile depended on DFM strain and diet and should be confirmed under a greater variation of dietary conditions. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of distillers dried grains with solubles on amino acid, energy, and fiber digestibility and on hindgut fermentation of dietary fiber in a corn-soybean meal diet fed to growing pigs.

PubMed

Urriola, P E; Stein, H H

2010-04-01

The objective of this experiment was to measure the effect of distillers dried grains with solubles (DDGS) on the digestibility of AA, energy, and fiber, on the fermentation of fiber, and on the first appearance of digesta at the end of the ileum, in the cecum, and in the feces of growing pigs fed a corn-soybean meal-based diet. Sixteen pigs (initial BW = 38.0 +/- 1.6 kg) were prepared with a T-cannula in the distal ileum and a T-cannula in the cecum and allotted to 2 treatments. In period 1, all pigs were fed a corn-soybean meal diet. In periods 2, 3, and 4, pigs were fed the control diet or a diet containing corn, soybean meal, and 30% DDGS. First appearance of digesta at the end of the ileum, in the cecum, and over the entire intestinal tract was measured at the end of period 4. The apparent ileal digestibility (AID) and the apparent total tract digestibility (ATTD) of nutrients were measured, and the concentration of VFA was analyzed in ileal, cecal, and fecal samples. The AID of Lys (74.1%) in the DDGS diet was less (P < 0.05) than in the control diet (78.6%), but the AID of most other AA and GE, NDF, and total dietary fiber (TDF) were not different between the 2 diets. The ATTD of GE (81.0%), NDF (57.2%), TDF (55.5%), and DM (81.7%) were less (P < 0.05) in the DDGS diet than in the control diet (86.0, 69.3, 66.0, and 87.2%, respectively). The concentration of VFA in ileal, cecal, and fecal samples was not different between pigs fed the 2 diets. The pH of ileal and cecal digesta from pigs fed the DDGS diet (6.3 and 5.5) was greater (P < 0.01) than from pigs fed the control diet (5.8 and 5.3). The ATTD of DM, GE, ADF, NDF, and TDF did not change with collection period, but the AID of ADF, NDF, and TDF increased (P < 0.05) from period 2 to period 4. The concentration of all VFA, except isobutyrate, was greater (P < 0.05) in cecal samples from period 4 compared with period 2, and the concentration of all VFA except propionate and isovalerate were greater (P < 0.05) in fecal samples collected in period 4 compared with those collected in period 2. The first appearance of digesta at the end of the ileum, in the cecum, and in the feces was not affected by DDGS. In conclusion, pigs fed the diet containing DDGS had less digestibility of Lys, GE, ADF, NDF, and TDF than pigs fed the control diet. The digestibility of DM and GE was not influenced by collection period, but the concentration of VFA in cecal digesta and feces increased with the length of time pigs received the diets.

Obstructive sleep apnea with excessive daytime sleepiness is associated with non-alcoholic fatty liver disease regardless of visceral fat

PubMed Central

Yu, Ji Hee; Ahn, Jae Hee; Yoo, Hye Jin; Seo, Ji A; Kim, Sin Gon; Choi, Kyung Mook; Baik, Sei Hyun; Choi, Dong Seop; Shin, Chol; Kim, Nan Hee

2015-01-01

Background/Aims: Obstructive sleep apnea (OSA) is associated with an increased risk of obesity and non-alcoholic fatty liver disease (NAFLD), but it remains unclear whether the risk of NAFLD is independently related to OSA regardless of visceral obesity. Thus, the aim of the present study was to examine whether OSA alone or in combination with excessive daytime sleepiness (EDS) or short sleep duration was associated with NAFLD independent of visceral fat in Korean adults. Methods: A total of 621 participants were selected from the Korean Genome and Epidemiology Study (KoGES). The abdominal visceral fat area (VFA) and hepatic fat components of the participants were assessed using computed tomography scans and they were then categorized into four groups depending on the presence of OSA and EDS. Results: The proportions of NAFLD were 21.1%, 18.5%, 32.4%, and 46.7% in participants without OSA/EDS, with only EDS, with only OSA, and with both OSA and EDS, respectively. A combination of OSA and EDS increased the odds ratio (OR) for developing NAFLD (OR, 2.75; 95% confidence interval [CI], 1.21 to 6.28) compared to those without OSA/EDS, and this association remained significant (OR, 2.38; 95% CI, 1.01 to 5.59) even after adjusting for VFA. In short sleepers (< 5 hours) with OSA, the adjusted OR for NAFLD was 2.50 (95% CI, 1.08 to 5.75) compared to those sleeping longer than 5 hours without OSA. Conclusions: In the present study, OSA was closely associated with NAFLD in Korean adults. This association was particularly strong in those with EDS or short sleep duration regardless of VFA. PMID:26552460

Simultaneous Hydrogen and Methane Production Through Multi-Phase Anaerobic Digestion of Paperboard Mill Wastewater Under Different Operating Conditions.

PubMed

Farghaly, Ahmed; Tawfik, Ahmed

2017-01-01

Multi-phase anaerobic reactor for H 2 and CH 4 production from paperboard mill wastewater was studied. The reactor was operated at hydraulic retention times (HRTs) of 12, 18, 24, and 36 h, and organic loading rates (OLRs) of 2.2, 1.5, 1.1, and 0.75 kg chemical oxygen demand (COD)/m 3  day, respectively. HRT of 12 h and OLR of 2.2 kg COD/m 3  day provided maximum hydrogen yield of 42.76 ± 14.5 ml/g COD removed and volumetric substrate uptake rate (-rS) of 16.51 ± 4.43 mg COD/L h. This corresponded to the highest soluble COD/total COD (SCOD/TCOD) ratio of 56.25 ± 3.3 % and the maximum volatile fatty acid (VFA) yield (Y VFA ) of 0.21 ± 0.03 g VFA/g COD, confirming that H 2 was mainly produced through SCOD conversion. The highest methane yield (18.78 ± 3.8 ml/g COD removed ) and -rS of 21.74 ± 1.34 mgCOD/L h were achieved at an HRT of 36 h and OLR of 0.75 kg COD/m 3  day. The maximum hydrogen production rate (HPR) and methane production rate (MPR) were achieved at carbon to nitrogen (C/N) ratio of 47.9 and 14.3, respectively. This implies the important effect of C/N ratio on the distinction between the dominant microorganism bioactivities responsible for H 2 and CH 4 production.

Physical activity and body composition changes during military service.

PubMed

Mikkola, Ilona; Jokelainen, Jari J; Timonen, Markku J; Härkönen, Pirjo K; Saastamoinen, Eero; Laakso, Mauri A; Peitso, Ari J; Juuti, Anna-Kaisa; Keinänen-Kiukaanniemi, Sirkka M; Mäkinen, Tiina M

2009-09-01

To examine how body composition changes in different body mass index (BMI) categories among young Finnish men during military service, which is associated with marked changes in diet and physical activity. In addition, this study examined how reported previous physical activity affected the body composition changes. Altogether 1003 men (19 yr) were followed throughout their military service (6-12 months). Height, weight, BMI, waist circumference, and waist-to-hip ratio (WHR) were recorded. Previous physical activity was assessed at the beginning of the service by a questionnaire. Body composition was measured by bioelectrical impedance assessments (BIA) at the beginning and at the end of the service. The measured parameters were fat mass (FM), fat percentage (fat %), fat-free mass (FFM), visceral fat area (VFA), lean body mass (LBM), and skeletal muscle mass (SMM). On average, military training decreased weight by 0.7%, FM by 9.7%, fat % by 6.6%, and VFA by 43.4%. FFM increased by 1.3%, LBM by 1.2%, and SMM by 1.7%. The group of underweight and normal-weight men gained weight, FM, and FFM, whereas overweight and obese men lost weight and FM and gained FFM. FM was most reduced in the groups of overweight (20.8%) and obese (24.9%) men. The amount of VFA was reduced in all BMI groups (38%-44%). Among overweight men who reported being inactive previous to the military service, more beneficial changes in body composition were observed compared with those who reported being physically active. The lifestyle changes associated with military service markedly reduce fat tissue and increase the amount of lean tissue. These beneficial changes are prominent among previously inactive subjects with high BMI.

Rumen microbial changes in cattle fed diets with or without salinomycin.

PubMed

Olumeyan, D B; Nagaraja, T G; Miller, G W; Frey, R A; Boyer, J E

1986-02-01

Four rumen-fistulated steers, randomly assigned to two groups (control and salinomycin fed) were used to monitor the changes in rumen microbial populations and volatile fatty acids (VFA) concentrations associated with feeding salinomycin (0.22 mg X kg-1 X day-1). Steers were adapted to an alfalfa hay and grain (80:20) diet before supplementing the diet with salinomycin, and then the diet was changed to 50:50 and 20:80 ratios of alfalfa hay to grain at 2-week intervals. Rumen samples for total and selective enumeration of anaerobic bacteria. VFA analysis, and enumeration of protozoa were collected during the 80:20 alfalfa hay-to-grain diet before salinomycin feeding, and during the 80:20, 50:50, and 20:80 hay-to-grain diets with salinomycin. At each sampling period, rumen samples were collected at 3 h after feeding on three consecutive days. Salinomycin feeding had no effect on rumen pH and total VFA concentration. The acetate-to-propionate ratio was significantly lower in salinomycin-fed steers than in the control. The molar proportion of butyrate increased in both control and salinomycin-fed steers. Total anaerobic bacterial counts were lower in salinomycin-fed steers than in the control steers after 8 weeks of salinomycin feeding. Salinomycin-resistant bacteria increased from 7.6 to 15.6% in salinomycin-fed steers but remained unchanged in control steers. Salinomycin had no effect on cellulolytic and lactate-utilizing bacteria, but the proportion of amylolytic bacteria was higher in salinomycin-fed steers than in control steers. The total number of protozoa decreased initially in salinomycin-fed steers. The initial reduction was due to reduced numbers of Entodinium species. Holotrichs were unaffected by salinomycin feeding.

Current practice and perspectives in CRO oversight based on a survey performed among members of the German Association of Research-Based Pharmaceutical Companies (vfa)

PubMed Central

Hennig, Michael; Hundt, Ferdinand; Busta, Susanne; Mikus, Stefan; Sanden, Per-Holger; Sörgel, Andrea; Ruppert, Thorsten

2017-01-01

In recent years, the number and scope of outsourced activities in the pharmaceutical industry have increased heavily. In addition, also the type of outsourcing has changed significantly in that time. This raises the question of whether and how sponsors retain the capability to select and to control the contract research organizations (CROs) involved and what expertise still has to be present in the development department as well as other relevant departments to ensure adequate oversight, also in line with the expectations of regulators and health authorities. In order to answer these questions, a survey was conducted among the German vfa member companies. The survey describes the latest developments and experiences in outsourcing by 18 German vfa member companies. It concentrates on measures how to implement Quality Assurance (QA) when performing outsourced clinical studies. This study shows that the majority of companies apply a full-outsourcing, preferred-provider model of clinical trial services, with the clinical research department playing the major role in this process. A large amount of guiding documents, processes and tools are used to ensure an adequate oversight of the services performed by the CRO(s). Finally the guiding principles for all oversight processes should be transparent communication, a clearly established expectation for quality, a precise definition of accountability and responsibility while avoiding silo mentality, and a comprehensive documentation of the oversight’s evidence. For globally acting and outsourcing sponsors, oversight processes need to be aligned with regards to local and global perspectives. This survey shows that the current implementation of oversight processes in the participating companies covers all relevant areas to ensure highest quality and integrity of the data produced by the outsourced clinical trial. PMID:28163667

Bacterial communities in the rumen of Holstein heifers differ when fed orchardgrass as pasture vs. hay

PubMed Central

Mohammed, Riazuddin; Brink, Geoffrey E.; Stevenson, David M.; Neumann, Anthony P.; Beauchemin, Karen A.; Suen, Garret; Weimer, Paul J.

2014-01-01

The rich and diverse microbiota of the rumen provides ruminant animals the capacity to utilize highly fibrous feedstuffs as their energy source, but there is surprisingly little information on the composition of the microbiome of ruminants fed all-forage diets, despite the importance of such agricultural production systems worldwide. In three 28-day periods, three ruminally-cannulated Holstein heifers sequentially grazed orchardgrass pasture (OP), then were fed orchardgrass hay (OH), then returned to OP. These heifers displayed greater shifts in ruminal bacterial community composition (determined by automated ribosomal intergenic spacer analysis and by pyrotag sequencing of 16S rRNA genes) than did two other heifers maintained 84 d on the same OP. Phyla Firmicutes and Bacteroidetes dominated all ruminal samples, and quantitative PCR indicated that members of the genus Prevotella averaged 23% of the 16S rRNA gene copies, well below levels previously reported with cows fed total mixed rations. Differences in bacterial community composition and ruminal volatile fatty acid (VFA) profiles were observed between the OP and OH despite similarities in gross chemical composition. Compared to OP, feeding OH increased the molar proportion of ruminal acetate (P = 0.02) and decreased the proportion of ruminal butyrate (P < 0.01), branched-chain VFA (P < 0.01) and the relative population size of the abundant genus Butyrivibrio (P < 0.001), as determined by pyrotag sequencing. Despite the low numbers of animals examined, the observed changes in VFA profile in the rumens of heifers on OP vs. OH are consistent with the shifts in Butyrivibrio abundance and its known physiology as a butyrate producer that ferments both carbohydrates and proteins. PMID:25538699

Reduction of visceral fat by liraglutide is associated with ameliorations of hepatic steatosis, albuminuria, and micro-inflammation in type 2 diabetic patients with insulin treatment: a randomized control trial.

PubMed

Bouchi, Ryotaro; Nakano, Yujiro; Fukuda, Tatsuya; Takeuchi, Takato; Murakami, Masanori; Minami, Isao; Izumiyama, Hajime; Hashimoto, Koshi; Yoshimoto, Takanobu; Ogawa, Yoshihiro

2017-03-31

Liraglutide, an analogue of human glucagon-like peptide 1, reduces cardiovascular events in patients with type 2 diabetes; however, it has still been unknown by which mechanisms liraglutide could reduce cardiovascular events. Type 2 diabetic patients with insulin treatment were enrolled in this randomized, open-label, comparative study. Participants were randomly assigned to liraglutide plus insulin (liraglutide group) and insulin treatment (control group) at 1:1 allocation. Primary endpoint was the change in viscera fat are (VFA, cm 2 ) at 24 weeks. Liver attenuation index (LAI) measured by abdominal computed tomography, urinary albumin-to-creatinine ratio (ACR, mg/g), and C-reactive protein (CRP) levels, skeletal muscle index (SMI), and quality of life (QOL) related to diabetes treatment were also determined. Seventeen patients (8; liraglutide group, 9; control group, mean age 59 ± 13 years; 53% female) completed this study. Liraglutide treatment significantly reduced VFA at 24 weeks; whereas, SFA was unchanged. ACR, LAI, and CRP levels were significantly reduced by liraglutide at 24 weeks and there was no difference in SMI between the two groups. Changes in VFA from baseline to 24 weeks were significantly associated with those in LAI, albuminuria, and HbA1c. Liraglutide treatment significantly improved QOL scores associated with anxiety and dissatisfaction with treatment and satisfaction with treatment. No severe adverse events were observed in both groups. Our data suggest that liraglutide could reduce visceral adiposity in parallel with attenuation of hepatic fat accumulation, albuminuria and micro-inflammation and improve QOL related to diabetes care in insulin-treated patients with type 2 diabetes.

Effects of synchronicity of carbohydrate and protein degradation on rumen fermentation characteristics and microbial protein synthesis.

PubMed

Seo, J K; Kim, M H; Yang, J Y; Kim, H J; Lee, C H; Kim, K H; Ha, Jong K

2013-03-01

A series of in vitro studies were carried out to determine i) the effects of enzyme and formaldehyde treatment on the degradation characteristics of carbohydrate and protein sources and on the synchronicity of these processes, and ii) the effects of synchronizing carbohydrate and protein supply on rumen fermentation and microbial protein synthesis (MPS) in in vitro experiments. Untreated corn (C) and enzyme-treated corn (EC) were combined with soy bean meal with (ES) and without (S) enzyme treatment or formaldehyde treatment (FS). Six experimental feeds (CS, CES, CFS, ECS, ECES and ECFS) with different synchrony indices were prepared. Highly synchronous diets had the greatest dry matter (DM) digestibility when untreated corn was used. However, the degree of synchronicity did not influence DM digestibility when EC was mixed with various soybean meals. At time points of 12 h and 24 h of incubation, EC-containing diets showed lower ammonia-N concentrations than those of C-containing diets, irrespective of the degree of synchronicity, indicating that more efficient utilization of ammonia-N for MPS was achieved by ruminal microorganisms when EC was offered as a carbohydrate source. Within C-containing treatments, the purine base concentration increased as the diets were more synchronized. This effect was not observed when EC was offered. There were significant effects on VFA concentration of both C and S treatments and their interactions. Similar to purine concentrations, total VFA production and individual VFA concentration in the groups containing EC as an energy source was higher than those of other groups (CS, CES and CFS). The results of the present study suggested that the availability of energy or the protein source are the most limiting factors for rumen fermentation and MPS, rather than the degree of synchronicity.

Current practice and perspectives in CRO oversight based on a survey performed among members of the German Association of Research-Based Pharmaceutical Companies (vfa).

PubMed

Hennig, Michael; Hundt, Ferdinand; Busta, Susanne; Mikus, Stefan; Sanden, Per-Holger; Sörgel, Andrea; Ruppert, Thorsten

2017-01-01

In recent years, the number and scope of outsourced activities in the pharmaceutical industry have increased heavily. In addition, also the type of outsourcing has changed significantly in that time. This raises the question of whether and how sponsors retain the capability to select and to control the contract research organizations (CROs) involved and what expertise still has to be present in the development department as well as other relevant departments to ensure adequate oversight, also in line with the expectations of regulators and health authorities. In order to answer these questions, a survey was conducted among the German vfa member companies. The survey describes the latest developments and experiences in outsourcing by 18 German vfa member companies. It concentrates on measures how to implement Quality Assurance (QA) when performing outsourced clinical studies. This study shows that the majority of companies apply a full-outsourcing, preferred-provider model of clinical trial services, with the clinical research department playing the major role in this process. A large amount of guiding documents, processes and tools are used to ensure an adequate oversight of the services performed by the CRO(s). Finally the guiding principles for all oversight processes should be transparent communication, a clearly established expectation for quality, a precise definition of accountability and responsibility while avoiding silo mentality, and a comprehensive documentation of the oversight's evidence. For globally acting and outsourcing sponsors, oversight processes need to be aligned with regards to local and global perspectives. This survey shows that the current implementation of oversight processes in the participating companies covers all relevant areas to ensure highest quality and integrity of the data produced by the outsourced clinical trial.

Serum Glycated Albumin Is Inversely Influenced by Fat Mass and Visceral Adipose Tissue in Chinese with Normal Glucose Tolerance

PubMed Central

Hao, Yaping; Yang, Rong; Ni, Jie; Xiao, Yunfeng; Tang, Junling; Bao, Yuqian; Jia, Weiping

2012-01-01

Background Recent studies have revealed that body mass index (BMI) inversely influenced serum glycated albumin (GA), which may cause an underestimation of GA-monitored short-term hyperglycemic control. Objective This study was to investigate the association between anthropometric variables (BMI and waist circumference (W)) and accurate adiposity variables (percentage of body fat (%fat), fat mass, free fat mass (FFM), subcutaneous fat area (SFA), and visceral fat area (VFA)) with serum GA. Design A total of 2563 subjects (1037 men, 593 premenopausal women, and 933 postmenopausal women) with normal glucose tolerance underwent bioelectrical impedance body fat content measurement and magnetic resonance imaging. Serum GA and absolute value of GA (aGA) were measured by enzymatic assay. Results Compared to the BMI <25.0 kg/m2 group, the BMI ≥25.0 kg/m2 group had significantly higher fasting plasma glucose, glycated hemoglobin A1c, and body fat parameters including W, %fat, fat mass, FFM, SFA, and VFA, but significantly lower aGA, and GA in all the three sex- and menopause-stratified groups (all P<0.05). GA decreased with the increment of fat mass for all three groups (all P for trend <0.001). In the same BMI category, men and postmenopausal women with elevated %fat (men, ≥25%; women, ≥35%) still had significantly lower GA than those with normal %fat (men, <25%; women, <35%) (all P<0.05). Multiple stepwise regression showed that %fat, fat mass, and VFA were independently associated with GA. Conclusions Serum GA was inversely influenced by fat mass and visceral adipose tissue in Chinese with normal glucose tolerance. PMID:23209844

Profile of Rumen Fermentation and Blood Urea Nitrogen Concentration of Kacang Goat Fed Total Mixed Ration Vs. Roughage

NASA Astrophysics Data System (ADS)

Adiwinarti, R.; Kustantinah; Budisatria, I. G. S.; Rusman; Indarto, E.

2018-02-01

Kacang goat is usually reared traditionally fed natural grass and having inferior performance. Many researches had been done to improve the performance. Total mixed ration (TMR) containing soybean meal (SBM) and fish meal (FM) could increase the performance of Kacang goat, but the profile of rumen fermentation has not been published. Therefore, this study investigated the profile of rumen fermentation and blood urea Nitrogen concentration (BUN) in Kacang goat fed natural grass (roughage) and TMR. Twelve yearling Kacang buck, 15.2-19.6 kg were arranged in completely randomized design. The treatments were NG (natural grass), FM (TMR containing FM), and SBM (TMR containing SBM). The TMR were formulated containing 15% crude protein and 56-58% TDN. Data were analyzed by one way ANOVA. Rumen pH 6 hours after feeding of NG (7.4) was higher (P<0.01) than that of FM (6.2) and SBM (6.4). This lowering pH of TMR was caused by increasing volatile fatty acids (VFA). The VFA total of FM (129.7 mmol/l) and SBM (153.1 mmol/l) were higher than that of NG (86.4 mmol/l). At 3 and 6 hours after feeding, ammonia in the rumen of SBM was higher than that of NG and FM, indicating higher degraded protein. The BUN at 3 hours after feeding of SBM was higher than that of NG. It can be concluded that protein in SBM was degraded higher than others and the lower pH in rumen of TMR goats was caused by higher VFA produced by TMR goats compared to NG goats.

Obstructive sleep apnea with excessive daytime sleepiness is associated with non-alcoholic fatty liver disease regardless of visceral fat.

PubMed

Yu, Ji Hee; Ahn, Jae Hee; Yoo, Hye Jin; Seo, Ji A; Kim, Sin Gon; Choi, Kyung Mook; Baik, Sei Hyun; Choi, Dong Seop; Shin, Chol; Kim, Nan Hee

2015-11-01

Obstructive sleep apnea (OSA) is associated with an increased risk of obesity and non-alcoholic fatty liver disease (NAFLD), but it remains unclear whether the risk of NAFLD is independently related to OSA regardless of visceral obesity. Thus, the aim of the present study was to examine whether OSA alone or in combination with excessive daytime sleepiness (EDS) or short sleep duration was associated with NAFLD independent of visceral fat in Korean adults. A total of 621 participants were selected from the Korean Genome and Epidemiology Study (KoGES). The abdominal visceral fat area (VFA) and hepatic fat components of the participants were assessed using computed tomography scans and they were then categorized into four groups depending on the presence of OSA and EDS. The proportions of NAFLD were 21.1%, 18.5%, 32.4%, and 46.7% in participants without OSA/EDS, with only EDS, with only OSA, and with both OSA and EDS, respectively. A combination of OSA and EDS increased the odds ratio (OR) for developing NAFLD (OR, 2.75; 95% confidence interval [CI], 1.21 to 6.28) compared to those without OSA/EDS, and this association remained significant (OR, 2.38; 95% CI, 1.01 to 5.59) even after adjusting for VFA. In short sleepers (< 5 hours) with OSA, the adjusted OR for NAFLD was 2.50 (95% CI, 1.08 to 5.75) compared to those sleeping longer than 5 hours without OSA. In the present study, OSA was closely associated with NAFLD in Korean adults. This association was particularly strong in those with EDS or short sleep duration regardless of VFA.

A survey and analysis of experimental hydrogen sensors

NASA Technical Reports Server (NTRS)

Hunter, Gary W.

1992-01-01

In order to ascertain the applicability of hydrogen sensors to aerospace applications, a survey was conducted of promising experimental point-contact hydrogen sensors and their operation was analyzed. The techniques discussed are metal-oxide-semiconductor or MOS based sensors, catalytic resistor sensors, acoustic wave detectors, and pyroelectric detectors. All of these sensors depend on the interaction of hydrogen with Pd or a Pd-alloy. It is concluded that no single technique will meet the needs of aerospace applications but a combination of approaches is necessary. The most promising combination is an MOS based sensor with a catalytic resistor.

Development of sensors for ceramic components in advanced propulsion systems: Survey and evaluation of measurement techniques for temperature, strain and heat flux for ceramic components in advanced propulsion systems

NASA Technical Reports Server (NTRS)

Atkinson, W. H.; Cyr, M. A.; Strange, R. R.

1988-01-01

The report presents the final results of Tasks 1 and 2, Development of Sensors for Ceramic Components in Advanced Propulsion Systems (NASA program NAS3-25141). During Task 1, an extensive survey was conducted of sensor concepts which have the potential for measuring surface temperature, strain and heat flux on ceramic components for advanced propulsion systems. Each sensor concept was analyzed and evaluated under Task 2; sensor concepts were then recommended for further development. For temperature measurement, both pyrometry and thermographic phosphors are recommended for measurements up to and beyond the melting point of ceramic materials. For lower temperature test programs, the thin-film techniques offer advantages in the installation of temperature sensors. Optical strain measurement techniques are recommended because they offer the possibility of being useful at very high temperature levels. Techniques for the measurement of heat flux are recommended for development based on both a surface mounted sensor and the measurement of the temperature differential across a portion of a ceramic component or metallic substrate.

Grass competition may benefit high density peach orchards

USDA-ARS?s Scientific Manuscript database

Previous research demonstrated that grass competition dwarfed and reduced the yield of individual peach trees [Prunus persica (L.) Batsch] grown in narrow vegetation free areas (VFA). In this report, the area-based yield of two peach cultivars, 'Redskin' and 'Jersey Dawn' on 'Lovell', was estimated...

Optical techniques for the determination of nitrate in environmental waters: Guidelines for instrument selection, operation, deployment, maintenance, quality assurance, and data reporting

USGS Publications Warehouse

Pellerin, Brian A.; Bergamaschi, Brian A.; Downing, Bryan D.; Saraceno, John Franco; Garrett, Jessica D.; Olsen, Lisa D.

2013-01-01

The recent commercial availability of in situ optical sensors, together with new techniques for data collection and analysis, provides the opportunity to monitor a wide range of water-quality constituents on time scales in which environmental conditions actually change. Of particular interest is the application of ultraviolet (UV) photometers for in situ determination of nitrate concentrations in rivers and streams. The variety of UV nitrate sensors currently available differ in several important ways related to instrument design that affect the accuracy of their nitrate concentration measurements in different types of natural waters. This report provides information about selection and use of UV nitrate sensors by the U.S. Geological Survey to facilitate the collection of high-quality data across studies, sites, and instrument types. For those in need of technical background and information about sensor selection, this report addresses the operating principles, key features and sensor design, sensor characterization techniques and typical interferences, and approaches for sensor deployment. For those needing information about maintaining sensor performance in the field, key sections in this report address maintenance and calibration protocols, quality-assurance techniques, and data formats and reporting. Although the focus of this report is UV nitrate sensors, many of the principles can be applied to other in situ optical sensors for water-quality studies.

Modelling mono-digestion of grass silage in a 2-stage CSTR anaerobic digester using ADM1.

PubMed

Thamsiriroj, T; Murphy, J D

2011-01-01

This paper examines 174 days of experimental data and modelling of mono-digestion of grass silage in a two stage wet process with recirculation of liquor; the two vessels have an effective volume of 312 L each. The organic loading rate is initiated at 0.5 kg VS m(-3) d(-1) (first 74 days) and subsequently increased to 1 kg VS m(-3) d(-1). The experimental data was used to generate a mathematical model (ADM1) which was calibrated over the first 74 days of operation. Good accuracy with experimental data was found for the subsequent 100 days. Results of the model would suggest starting the process without recirculation and thus building up the solids content of the liquor. As the level of VFA increases, recirculation should be employed to control VFA. Recirculation also controls solids content and pH. Methane production was estimated at 88% of maximum theoretical production. Copyright © 2010 Elsevier Ltd. All rights reserved.

Removal of volatile fatty acids and ammonia recovery from unstable anaerobic digesters with a microbial electrolysis cell.

PubMed

Cerrillo, Míriam; Viñas, Marc; Bonmatí, August

2016-11-01

Continuous assays with a microbial electrolysis cell (MEC) fed with digested pig slurry were performed to evaluate its stability and robustness to malfunction periods of an anaerobic digestion (AD) reactor and its feasibility as a strategy to recover ammonia. When performing punctual pulses of volatile fatty acids (VFA) in the anode compartment of the MEC, simulating a malfunction of the AD process, an increase in the current density was produced (up to 14 times, reaching values of 3500mAm(-2)) as a result of the added chemical oxygen demand (COD), especially when acetate was used. Furthermore, ammonium diffusion from the anode to the cathode compartment was enhanced and the removal efficiency achieved up to 60% during daily basis VFA pulses. An AD-MEC combined system has proven to be a robust and stable configuration to obtain a high quality effluent, with a lower organic and ammonium content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of trace element addition on process stability during anaerobic co-digestion of OFMSW and slaughterhouse waste.

PubMed

Moestedt, J; Nordell, E; Shakeri Yekta, S; Lundgren, J; Martí, M; Sundberg, C; Ejlertsson, J; Svensson, B H; Björn, A

2016-01-01

This study used semi-continuous laboratory scale biogas reactors to simulate the effects of trace-element addition in different combinations, while degrading the organic fraction of municipal solid waste and slaughterhouse waste. The results show that the combined addition of Fe, Co and Ni was superior to the addition of only Fe, Fe and Co or Fe and Ni. However, the addition of only Fe resulted in a more stable process than the combined addition of Fe and Co, perhaps indicating a too efficient acidogenesis and/or homoacetogenesis in relation to a Ni-deprived methanogenic population. The results were observed in terms of higher biogas production (+9%), biogas production rates (+35%) and reduced VFA concentration for combined addition compared to only Fe and Ni. The higher stability was supported by observations of differences in viscosity, intraday VFA- and biogas kinetics as well as by the 16S rRNA gene and 16S rRNA of the methanogens. Copyright © 2015 Elsevier Ltd. All rights reserved.

Bioconversion of volatile fatty acids derived from waste activated sludge into lipids by Cryptococcus curvatus.

PubMed

Liu, Jia; Liu, Jia-Nan; Yuan, Ming; Shen, Zi-Heng; Peng, Kai-Ming; Lu, Li-Jun; Huang, Xiang-Feng

2016-07-01

Pure volatile fatty acid (VFA) solution derived from waste activated sludge (WAS) was used to produce microbial lipids as culture medium in this study, which aimed to realize the resource recovery of WAS and provide low-cost feedstock for biodiesel production simultaneously. Cryptococcus curvatus was selected among three oleaginous yeast to produce lipids with VFAs derived from WAS. In batch cultivation, lipid contents increased from 10.2% to 16.8% when carbon to nitrogen ratio increased from about 3.5 to 165 after removal of ammonia nitrogen by struvite precipitation. The lipid content further increased to 39.6% and the biomass increased from 1.56g/L to 4.53g/L after cultivation for five cycles using sequencing batch culture (SBC) strategy. The lipids produced from WAS-derived VFA solution contained nearly 50% of monounsaturated fatty acids, including palmitic acid, heptadecanoic acid, ginkgolic acid, stearic acid, oleic acid, and linoleic acid, which showed the adequacy of biodiesel production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Enhancement of Anaerobic Digestion to Treat Saline Sludge from Recirculating Aquaculture Systems

PubMed Central

Luo, Guo-zhi; Ma, Niannian; Li, Ping; Tan, Hong-xin; Liu, Wenchang

2015-01-01

The effectiveness of carbohydrate addition and the use of ultrasonication as a pretreatment for the mesophilic anaerobic digestion of saline aquacultural sludge was assessed. Analyses were conducted using an anaerobic sequencing batch reactor (ASBR), which included stopped gas production attributed to the saline inhibition. After increasing the C : N ratio, gas production was observed, and the total chemical oxygen demand (TCOD) removal efficiency increased from 75% to 80%. The TCOD removal efficiency of the sonication period was approximately 85%, compared to 75% for the untreated waste. Ultrasonication of aquaculture sludge was also found to enhance the gas production rate and the TCOD removal efficiency. The average volatile fatty acid (VFA) to alkalinity ratios ranged from 0.1 to 0.05, confirming the stability of the digesters. Furthermore, soluble chemical oxygen demand (SCOD), VFA, and PO4 3− concentrations increased in the effluents. There was a 114% greater gas generation during the ultrasonication period, with an average production of 0.08 g COD/L·day−1. PMID:26301258

Effect of covering composting piles with mature compost on ammonia emission and microbial community structure of composting process.

PubMed

Maeda, Koki; Morioka, Riki; Osada, Takashi

2009-01-01

To control ammonia (NH(3)) volatilization from the dairy cattle (Bos taurus) manure composting process, a compost pile was covered with mature compost and the gas emissions evaluated using the dynamic chamber system. The peak of NH(3) volatilization observed immediately after piling up of the compost was reduced from 196 to 62 mg/m(3) by covering the compost pile with mature compost. The accumulation of NH(4)-N to the covered mature compost was also observed. Covering and mixing the compost with mature compost had no effect on the microbial community structure. However, over time the microbial community structure changed because of a decrease in easily degradable organic compounds in the compost piles. The availability of volatile fatty acids (VFA) was considered to be important for microbial community structure in the compost. After the VFA had disappeared, the NO(3)-N concentration increased and the cellulose degrading bacteria such as Cytophaga increased in number.

Leachate flush strategies for managing volatile fatty acids accumulation in leach-bed reactors.

PubMed

Riggio, S; Torrijos, M; Vives, G; Esposito, G; van Hullebusch, E D; Steyer, J P; Escudié, R

2017-05-01

In anaerobic leach-bed reactors (LBRs) co-digesting an easily- and a slowly-degradable substrate, the importance of the leachate flush both on extracting volatile fatty acids (VFAs) at the beginning of newly-started batches and on their consumption in mature reactors was tested. Regarding VFA extraction three leachate flush-rate conditions were studied: 0.5, 1 and 2Lkg -1 TSd -1 . Results showed that increasing the leachate flush-rate during the acidification phase is essential to increase degradation kinetics. After this initial phase, leachate injection is less important and the flush-rate could be reduced. The injection in mature reactors of leachate with an acetic acid concentration of 5 or 10gL -1 showed that for an optimized VFA consumption in LBRs, VFAs should be provided straight after the methane production peak in order to profit from a higher methanogenic activity, and every 6-7h to maintain a high biogas production rate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Identification of crude-oil components and microorganisms that cause souring under anaerobic conditions.

PubMed

Hasegawa, R; Toyama, K; Miyanaga, K; Tanji, Y

2014-02-01

Oil souring has important implications with respect to energy resources. Understanding the physiology of the microorganisms that play a role and the biological mechanisms are both important for the maintenance of infrastructure and mitigation of corrosion processes. The objective of this study was to identify crude-oil components and microorganisms in oil-field water that contribute to crude-oil souring. To identify the crude-oil components and microorganisms that are responsible for anaerobic souring in oil reservoirs, biological conversion of crude-oil components under anaerobic conditions was investigated. Microorganisms in oil field water in Akita, Japan degraded alkanes and aromatics to volatile fatty acids (VFAs) under anaerobic conditions, and fermenting bacteria such as Fusibacter sp. were involved in VFA production. Aromatics such as toluene and ethylbenzene were degraded by sulfate-reducing bacteria (Desulfotignum sp.) via the fumarate-addition pathway and not only degradation of VFA but also degradation of aromatics by sulfate-reducing bacteria was the cause of souring. Naphthenic acid and 2,4-xylenol were not converted.

Instability mechanisms and early warning indicators for mesophilic anaerobic digestion of vegetable waste.

PubMed

Li, Dong; Chen, Lin; Liu, Xiaofeng; Mei, Zili; Ren, Haiwei; Cao, Qin; Yan, Zhiying

2017-12-01

In order to elucidate the instability mechanism, screen early warning indicators, and propose control measures, the mesophilic digestion of vegetable waste (VW) was carried out at organic loading rates (OLR) of 0.5, 1.0, and 1.5g volatile solid (VS)/(Ld). The process parameters, including biogas components, volatile fatty acids (VFA), ammonia, pH, total alkalinity (TA), bicarbonate alkalinity (BA), and intermediate alkalinity (IA), were monitored every day. Digestion was inhibited at OLR of 1.5gVS/(Ld). The primary causes of instability are a high sugar and negligible ammonia content, in addition to the feed without effluent recirculation, which led to BA loss. The ratios of CH 4 /CO 2 , VFA/BA, propionate, n-butyrate and iso-valerate were selected as early warning indicators. In order to maintain the digestion of VW at a high OLR, control measures including effluent recirculation and trace element addition are recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of substrate and cation requirement on anaerobic volatile fatty acid conversion rates at elevated biogas pressure.

PubMed

Lindeboom, Ralph E F; Ferrer, Ivet; Weijma, Jan; van Lier, Jules B

2013-12-01

This work studied the anaerobic conversion of neutralized volatile fatty acids (VFA) into biogas under Autogenerative High Pressure Digestion (AHPD) conditions. The effects of the operating conditions on the biogas quality, and the substrate utilisation rates were evaluated using 3 AHPD reactors (0.6 L); feeding a concentration of acetate and VFA (1-10 g COD/L) corresponding to an expected pressure increase of 1-20 bar. The biogas composition improved with pressure up to 4.5 bar (>93% CH4), and stabilized at 10 and 20 bar. Both, acetotrophic and hydrogenotrophic methanogenic activity was observed. Substrate utilisation rates of 0.2, 0.1 and 0.1 g CODCH4/g VSS/d for acetate, propionate and butyrate were found to decrease by up to 50% with increasing final pressure. Most likely increased Na(+)-requirement to achieve CO2 sequestration at higher pressure rather than end-product inhibition was responsible. Copyright © 2013 Elsevier Ltd. All rights reserved.

Anaerobic hydrolysis and acidification of organic substrates: determination of anaerobic hydrolytic potential.

PubMed

Rajagopal, Rajinikanth; Béline, Fabrice

2011-05-01

This study aimed to develop a biochemical-test mainly to evaluate the hydrolytic-potential of different substrates and to apply this test to characterize various organic substrates. Outcome of this study can be used for optimization of the WWTPs through enhancement of N/P removal or anaerobic digestion. Out of four series of batch experiments, the first two tests were conducted to determine the optimal operating conditions (test duration, inoculum-ratio etc.) for the hydrolytic-potential test using secondary and synthetically-prepared sludges. Based on the results (generation of CODs, pH and VFA), test duration was fixed between 6 and 7d allowing to attain maximum hydrolysis and to avoid methanogenesis. Effect of inoculum-ratios on acid fermentation of sludge was not significantly noticed. Using this methodology, third and fourth tests were performed to characterize various organic substrates namely secondary, pre-treated sludge, pig and two different cattle slurries. VFA production was shown to be substantially dependent on substrates types. Copyright © 2011 Elsevier Ltd. All rights reserved.

Dynamic model inversion techniques for breath-by-breath measurement of carbon dioxide from low bandwidth sensors.

PubMed

Sivaramakrishnan, Shyam; Rajamani, Rajesh; Johnson, Bruce D

2009-01-01

Respiratory CO(2) measurement (capnography) is an important diagnosis tool that lacks inexpensive and wearable sensors. This paper develops techniques to enable use of inexpensive but slow CO(2) sensors for breath-by-breath tracking of CO(2) concentration. This is achieved by mathematically modeling the dynamic response and using model-inversion techniques to predict input CO(2) concentration from the slow-varying output. Experiments are designed to identify model-dynamics and extract relevant model-parameters for a solidstate room monitoring CO(2) sensor. A second-order model that accounts for flow through the sensor's filter and casing is found to be accurate in describing the sensor's slow response. The resulting estimate is compared with a standard-of-care respiratory CO(2) analyzer and shown to effectively track variation in breath-by-breath CO(2) concentration. This methodology is potentially useful for measuring fast-varying inputs to any slow sensor.

Embedding of MEMS pressure and temperature sensors in carbon fiber composites: a manufacturing approach

NASA Astrophysics Data System (ADS)

Javidinejad, Amir; Joshi, Shiv P.

2000-06-01

In this paper embedding of surface mount pressure and temperature sensors in the Carbon fiber composites are described. A commercially available surface mount pressure and temperature sensor are used for embedding in a composite lay- up of IM6/HST-7, IM6/3501 and AS4/E7T1-2 prepregs. The fabrication techniques developed here are the focus of this paper and provide for a successful embedding procedure of pressure sensors in fibrous composites. The techniques for positioning and insulating, the sensor and the lead wires, from the conductive carbon prepregs are described and illustrated. Procedural techniques are developed and discussed for isolating the sensor's flow-opening, from the exposure to the prepreg epoxy flow and exposure to the fibrous particles, during the autoclave curing of the composite laminate. The effects of the autoclave cycle (if any) on the operation of the embedded pressure sensor are discussed.

An analysis of the uncertainty and bias in DCE-MRI measurements using the spoiled gradient-recalled echo pulse sequence.

PubMed

Subashi, Ergys; Choudhury, Kingshuk R; Johnson, G Allan

2014-03-01

The pharmacokinetic parameters derived from dynamic contrast-enhanced (DCE) MRI have been used in more than 100 phase I trials and investigator led studies. A comparison of the absolute values of these quantities requires an estimation of their respective probability distribution function (PDF). The statistical variation of the DCE-MRI measurement is analyzed by considering the fundamental sources of error in the MR signal intensity acquired with the spoiled gradient-echo (SPGR) pulse sequence. The variance in the SPGR signal intensity arises from quadrature detection and excitation flip angle inconsistency. The noise power was measured in 11 phantoms of contrast agent concentration in the range [0-1] mM (in steps of 0.1 mM) and in onein vivo acquisition of a tumor-bearing mouse. The distribution of the flip angle was determined in a uniform 10 mM CuSO4 phantom using the spin echo double angle method. The PDF of a wide range of T1 values measured with the varying flip angle (VFA) technique was estimated through numerical simulations of the SPGR equation. The resultant uncertainty in contrast agent concentration was incorporated in the most common model of tracer exchange kinetics and the PDF of the derived pharmacokinetic parameters was studied numerically. The VFA method is an unbiased technique for measuringT1 only in the absence of bias in excitation flip angle. The time-dependent concentration of the contrast agent measured in vivo is within the theoretically predicted uncertainty. The uncertainty in measuring K(trans) with SPGR pulse sequences is of the same order, but always higher than, the uncertainty in measuring the pre-injection longitudinal relaxation time (T10). The lowest achievable bias/uncertainty in estimating this parameter is approximately 20%-70% higher than the bias/uncertainty in the measurement of the pre-injection T1 map. The fractional volume parameters derived from the extended Tofts model were found to be extremely sensitive to the variance in signal intensity. The SNR of the pre-injection T1 map indicates the limiting precision with which K(trans) can be calculated. Current small-animal imaging systems and pulse sequences robust to motion artifacts have the capacity for reproducible quantitative acquisitions with DCE-MRI. In these circumstances, it is feasible to achieve a level of precision limited only by physiologic variability.

Sensor failure and multivariable control for airbreathing propulsion systems. Ph.D. Thesis - Dec. 1979 Final Report

NASA Technical Reports Server (NTRS)

Behbehani, K.

1980-01-01

A new sensor/actuator failure analysis technique for turbofan jet engines was developed. Three phases of failure analysis, namely detection, isolation, and accommodation are considered. Failure detection and isolation techniques are developed by utilizing the concept of Generalized Likelihood Ratio (GLR) tests. These techniques are applicable to both time varying and time invariant systems. Three GLR detectors are developed for: (1) hard-over sensor failure; (2) hard-over actuator failure; and (3) brief disturbances in the actuators. The probability distribution of the GLR detectors and the detectability of sensor/actuator failures are established. Failure type is determined by the maximum of the GLR detectors. Failure accommodation is accomplished by extending the Multivariable Nyquest Array (MNA) control design techniques to nonsquare system designs. The performance and effectiveness of the failure analysis technique are studied by applying the technique to a turbofan jet engine, namely the Quiet Clean Short Haul Experimental Engine (QCSEE). Single and multiple sensor/actuator failures in the QCSEE are simulated and analyzed and the effects of model degradation are studied.

Distributed Transforms for Efficient Data Gathering in Sensor Networks

NASA Technical Reports Server (NTRS)

Ortega, Antonio (Inventor); Shen, Godwin (Inventor); Narang, Sunil K. (Inventor); Perez-Trufero, Javier (Inventor)

2014-01-01

Devices, systems, and techniques for data collecting network such as wireless sensors are disclosed. A described technique includes detecting one or more remote nodes included in the wireless sensor network using a local power level that controls a radio range of the local node. The technique includes transmitting a local outdegree. The local outdegree can be based on a quantity of the one or more remote nodes. The technique includes receiving one or more remote outdegrees from the one or more remote nodes. The technique includes determining a local node type of the local node based on detecting a node type of the one or more remote nodes, using the one or more remote outdegrees, and using the local outdegree. The technique includes adjusting characteristics, including an energy usage characteristic and a data compression characteristic, of the wireless sensor network by selectively modifying the local power level and selectively changing the local node type.

Digestion of rice straw and oil palm fronds by microflora from rumen and termite bacteria, in vitro.

PubMed

Ramin, M; Alimon, A R; Panandam, J M; Sijam, K; Javanmard, A; Abdullah, N

2008-02-15

The digestion and Volatile Fatty Acid (VFA) production from rice straw and oil palm fronds by cellulolytic bacteria isolated from the termite Coptotermes curvignathus were investigated. The bacteria were Acinetobacter strain Raminalimon, Enterobacter aerogenes strain Razmin C, Enterobacter cloacae strain Razmin B, Bacillus cereus strain Razmin A and Chryseobacterium kwangyangense strain Cb. Acinetobacter strain Raminalimon is an aerobic bacterium, while the other species are facultative anaerobes. There were significant differences (p<0.05) among the bacteria for Dry Matter (DM) lost and acetic acid production from rice straw and Acinetobacter strain Raminalimon showed the highest activity. The facultative bacteria C. kwangyangense strain Cb (cfu mL(-1) 231 x 10(-6), OD: 0.5), E. cloacae (cfu mL(-1) 68 x 10(-7), OD: 0.5) and E. aerogenes (cfu mL(-1) 33 x 10(-7), OD: 0.5) were used for digestion study with the rumen fluid microflora. The in vitro gas production technique was applied for the comparative study and the parameters measured were pH, gas (volume), dry matter lost, acetic acid, propionic acid and butyric acid concentrations. pH was not significantly (p<0.05) different among the five treatments. The bacterium C. kwangyangense strain Cb showed the highest activity (p<0.05) for DM lost, acetic acid, propionic acid and butyric acid production from rice straw when compared to the other bacterial activities. There was no significance (p<0.05) difference between the three bacteria for the dry matter lost of oil palm fronds but the production of Volatile Fatty Acids (VFA) was significantly (p<0.05) high in the treatment which was inoculated with C. kwangyangense strain Cb. The Gen Bank NCBI/EMBL accession numbers for the bacterial strains are EU332791, EU305608, EU305609, EU294508 and EU169201.

Microbiological characterization and specific methanogenic activity of anaerobe sludges used in urban solid waste treatment.

PubMed

Lozano, Claudia Johanna Sandoval; Mendoza, Marisol Vergara; de Arango, Mariela Carreño; Monroy, Edgar Fernando Castillo

2009-02-01

This study presents the microbiological characterization of the anaerobic sludge used in a two-stage anaerobic reactor for the treatment of organic fraction of urban solid waste (OFUSW). This treatment is one alternative for reducing solid waste in landfills at the same time producing a biogas (CH(4) and CO(2)) and an effluent that can be used as biofertilizer. The system was inoculated with sludge from a wastewater treatment plant (WWTP) (Río Frío Plant in Bucaramanga-Colombia) and a methanogenic anaerobic digester for the treatment of pig manure (Mesa de los Santos in Santander). Bacterial populations were evaluated by counting groups related to oxygen sensitivity, while metabolic groups were determined by most probable number (MPN) technique. Specific methanogenic activity (SMA) for acetate, formate, methanol and ethanol substrates was also determined. In the acidogenic reactor (R1), volatile fatty acids (VFA) reached values of 25,000 mg L(-1) and a concentration of CO(2) of 90%. In this reactor, the fermentative population was predominant (10(5)-10(6)MPN mL(-1)). The acetogenic population was (10(5)MPN mL(-1)) and the sulphate-reducing population was (10(4)-10(5)MPN mL(-1)). In the methanogenic reactor (R2), levels of CH(4) (70%) were higher than CO(2) (25%), whereas the VFA values were lower than 4000 mg L(-1). Substrate competition between sulphate-reducing (10(4)-10(5)MPN mL(-1)) and methanogenic bacteria (10(5)MPN mL(-1)) was not detected. From the SMA results obtained, acetoclastic (2.39 g COD-CH(4)g(-1)VSS(-1)day(-1)) and hydrogenophilic (0.94 g COD-CH(4)g(-1)VSS(-1)day(-1)) transformations as possible metabolic pathways used by methanogenic bacteria is suggested from the SMA results obtained. Methanotrix sp., Methanosarcina sp., Methanoccocus sp. and Methanobacterium sp. were identified.

Butyrate: A dietary inhibitor of histone deacetylases and an epigenetic regulator

USDA-ARS?s Scientific Manuscript database

The short-chain fatty acids (SCFAs) acetate, propionate and butyrate, also known as volatile fatty acids (VFA), are produced in the gastrointestinal tract by microbial fermentation. Consumption of dietary fibers has been shown to have positive metabolic health effects, such as increasing satiety, an...

Development of a 4.75-mm (No. 4) NMS mixture : research project capsule.

DOT National Transportation Integrated Search

2017-08-01

The objective of this project is to develop a 4.75-mm NMAS asphalt mixture for Louisiana roads, which will involve establishing target criteria for aggregate gradations, volumetric properties (e.g., air voids, VMA, VFA, and dust-to-binder ratio) and ...

Effect of trace minerals and starch on digestibility and rumen fermentation in diets for dairy heifers.

PubMed

Pino, F; Heinrichs, A J

2016-04-01

The objective of this study was to evaluate the effect of different forms of trace minerals (TM) and the use of different starch levels in dairy heifer diets on rumen fermentation and digestibility. Eight rumen cannulated dairy heifers (15.4 ± 0.8 mo of age and 438.31 ± 18.08 kg of body weight) were subjected to a split-plot, 4 × 4 Latin square design with 19-d periods: 15d of adaptation and 4d of sampling. The whole-plot factor was type of TM; organic as proteinates (OTM) or inorganic sulfates (ITM), and the subplot was starch level (3.54, 12.95, 22.25, and 31.73%). Total collection of feces and urine was completed on d 15 to 19 to determine digestibility and TM excretion. Rumen contents were sampled on d 18 to 19 at 0, 1, 2, 4, 8, 12, 16, 20, and 22 h after feeding to measure pH and volatile fatty acid (VFA) concentrations. Plasma samples were collected to evaluate TM concentrations and enzymatic activity for ceruloplasmin, glutathione peroxidase, and superoxide dismutase. Starch level affected pH, individual VFA concentrations, and nutrient excretion. Trace mineral intake was lower for OTM compared with ITM. No effect of TM form on dry matter digestibility was detected, but as level of starch increased, diet dry matter digestibility increased. Rumen pH was lower for diets with OTM, which is consistent with higher total VFA production and butyrate proportion observed for heifers fed OTM diets. These variables may be explained by the higher bioavailability of OTM and faster utilization and fermentation by rumen microorganisms. Heifers that consumed ITM had higher moisture in feces and higher urine excretion, which increased total manure production. Total excretion of TM was not different by treatment. Blood plasma mineral concentration was not different between treatments except for Mn, which was higher for OTM. Enzymatic activity was not affected by treatments. Mineral intake was reduced and blood mineral levels were not different, suggesting enhanced absorption of OTM compared with ITM. In conclusion, based on rumen pH, VFA production, and plasma TM concentration, OTM may be more ruminally bioavailable and absorbed to a greater extent than ITM. Also, TM form affected fecal moisture and urine excretion, suggesting that ITM may stimulate water intake. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

High-Temperature Strain Sensing for Aerospace Applications

NASA Technical Reports Server (NTRS)

Piazza, Anthony; Richards, Lance W.; Hudson, Larry D.

2008-01-01

Thermal protection systems (TPS) and hot structures are utilizing advanced materials that operate at temperatures that exceed abilities to measure structural performance. Robust strain sensors that operate accurately and reliably beyond 1800 F are needed but do not exist. These shortcomings hinder the ability to validate analysis and modeling techniques and hinders the ability to optimize structural designs. This presentation examines high-temperature strain sensing for aerospace applications and, more specifically, seeks to provide strain data for validating finite element models and thermal-structural analyses. Efforts have been made to develop sensor attachment techniques for relevant structural materials at the small test specimen level and to perform laboratory tests to characterize sensor and generate corrections to apply to indicated strains. Areas highlighted in this presentation include sensors, sensor attachment techniques, laboratory evaluation/characterization of strain measurement, and sensor use in large-scale structures.

A fast response, low heat generating activation method for LHe level sensors

NASA Astrophysics Data System (ADS)

Choudhury, Anup; Sahu, Santosh; Kanjilal, Dinakar

2018-06-01

A superconducting liquid helium (LHe) level sensor of length 300 mm has been fabricated based on the principle of differential heat transfer characteristic in helium gas compared to that in liquid. The sensor wire used has a diameter of 38 μm, and the wire was obtained from a pack of multifilament wires. A full thermo-electrical characterisation of the sensor was carried out in a dedicated setup. Its dynamic thermal response was also studied to understand its timing characteristics at different liquid levels and excitation currents. Based on the sensor characterisation, a new level measurement technique is evaluated which can reduce the heat load going to LHe during sensor activation without compromising on its sensitivity or accuracy. The timing response with this technique will make the level detection faster compared to the conventional techniques.

Investigation of optical/infrared sensor techniques for application satellites

NASA Technical Reports Server (NTRS)

Kaufman, I.

1972-01-01

A method of scanning an optical sensor array by acoustic surface waves is discussed. Data cover detailed computer based analysis of the operation of a multielement acoustic surface-wave-scanned optical sensor, the development of design and operation techniques that were used to show the feasibility of an integrated array to design several such arrays, and experimental verification of a number of the calculations with discrete sensor devices.

Image restoration using aberration taken by a Hartmann wavefront sensor on extended object, towards real-time deconvolution

NASA Astrophysics Data System (ADS)

Darudi, Ahmad; Bakhshi, Hadi; Asgari, Reza

2015-05-01

In this paper we present the results of image restoration using the data taken by a Hartmann sensor. The aberration is measure by a Hartmann sensor in which the object itself is used as reference. Then the Point Spread Function (PSF) is simulated and used for image reconstruction using the Lucy-Richardson technique. A technique is presented for quantitative evaluation the Lucy-Richardson technique for deconvolution.

Pulse oximeter sensor application during neonatal resuscitation: a randomized controlled trial.

PubMed

Louis, Deepak; Sundaram, Venkataseshan; Kumar, Praveen

2014-03-01

This study was done to compare 2 techniques of pulse oximeter sensor application during neonatal resuscitation for faster signal detection. Sensor to infant first (STIF) and then to oximeter was compared with sensor to oximeter first (STOF) and then to infant in ≥28 weeks gestations. The primary outcome was time from completion of sensor application to reliable signal, defined as stable display of heart rate and saturation. Time from birth to sensor application, time taken for sensor application, time from birth to reliable signal, and need to reapply sensor were secondary outcomes. An intention-to-treat analysis was done, and subgroup analysis was done for gestation and need for resuscitation. One hundred fifty neonates were randomized with 75 to each technique. The median (IQR) time from sensor application to detection of reliable signal was longer in STIF group compared with STOF group (16 [15-17] vs. 10 [6-18] seconds; P <0.001). Time taken for application of sensor was longer with STIF technique than with STOF technique (12 [10-16] vs. 11 [9-15] seconds; P = 0.04). Time from birth to reliable signal did not differ between the 2 methods (STIF: 61 [52-76] seconds; STOF: 58 [47-73] seconds [P = .09]). Time taken for signal acquisition was longer with STIF than with STOF in both subgroups. In the delivery room setting, the STOF method recognized saturation and heart rate faster than the STIF method. The time from birth to reliable signal was similar with the 2 methods.

Fiber optic and laser sensors X; Proceedings of the Meeting, Boston, MA, Sept. 8-11, 1992

NASA Technical Reports Server (NTRS)

Udd, Eric (Editor); Depaula, Ramon P. (Editor)

1993-01-01

Topics addressed include acoustic and pressure sensors; fiber optic gyros; electric and magnetic field sensors; bend, strain, and temperature sensors; industrial applications of sensors; and processing techniques. Particular attention is given to fiber optic interferometric acoustic sensors for wind tunnel applications, polished coupler and resonator fabrication, second-harmonic detection for rotation sensing in fiber optic gyros, simplified control theory in closed-loop fiber optic gyroscopes, and a Fabry-Perot sensor with digital signal processing for the measurement of magnetostriction. Also discussed are a Bragg fiber laser sensor, commercialization of fiber optic strain gauge systems, thermal ignition in hazardous environments due to stray light from optical fibers, a system for absolute measurements by interferometric sensors, and high-performance interferometric demodulation techniques.

Made to Measure: College Leaders Come Together to Strengthen Institutional Accountability

ERIC Educational Resources Information Center

Boerner, Heather

2015-01-01

Since the American Association of Community Colleges (AACC) launched the Voluntary Framework of Accountability (VFA) in 2011, accountability measures have sprung up in just about every corner of higher education. There is the Integrated Postsecondary Education Data System (IPEDS), the National Governors Association's Complete to Compete program,…

Nutrient-induced modulation of gene expression and cellular functions: modeling epigenetic regulation in bovine cells

USDA-ARS?s Scientific Manuscript database

Volatile fatty acids (VFA), especially butyrate, participate in metabolism both as nutrients and as regulators of histone deacetylation. The major biochemical change that occurs in cells treated with butyrate is the global hyperacetylation of histones. One paradigmatic example of the nutrient-epige...

Perturbation dynamics of the rumen microbiota in response to exogenous butyrate

USDA-ARS?s Scientific Manuscript database

The capacity of the rumen microbiota to produce volatile fatty acids (VFA) has important implications in animal well-being and production. We investigated temporal changes of the rumen microbiota in response to butyrate infusion using pyrosequencing of the 16S rRNA gene. Phyla were identified in ...

Dietary Habits Prone to Lifestyle-Related Disease

ERIC Educational Resources Information Center

Nagai, M.; Uyama, O.; Kaji, H.

2013-01-01

Objective: To evaluate relations among dietary habits, bone mineral density (BMD), visceral fat area (VFA), and arterial stiffness and recommend better dietary habits. Methods: One hundred and six men and 381 women (aged 18-84) received a health checkup and answered questionnaires, with subsequent measurements of BMD (speed of sound), VFA…

Resolution enhancement of fiber Bragg grating temperature sensor using a cavity ring-down technique

NASA Astrophysics Data System (ADS)

Yarai, Atsushi; Hara, Katsuyuki

2018-02-01

A new technique for enhancing the measurement resolution of a fiber Bragg grating (FBG) temperature sensor is proposed. This technique uses a cavity ring-down approach to amplify optical intensity by accumulating unremarkable intensity changes. A wavelength-stabilized optical pulse with a width of 10 ns rotates several times inside an optical fiber loop that contains a FBG sensor. In other words, the loop system functions as an integrator of slight intensity transition. A temperature resolution of at least 0.02 °C was achieved at 20.0 °C. Resolution with this technique is at least five times higher than previous techniques.

Fiber optic and laser sensors IV; Proceedings of the Meeting, Cambridge, MA, Sept. 22-24, 1986

NASA Technical Reports Server (NTRS)

De Paula, Ramon P. (Editor); Udd, Eric (Editor)

1987-01-01

The conference presents papers on industrial uses of fiber optic sensors, point and distributed polarimetric optical fiber sensors, fiber optic electric field sensor technology, micromachined resonant structures, single-mode fibers for sensing applications, and measurement techniques for magnetic field gradient detection. Consideration is also given to electric field meter and temperature measurement techniques for the power industry, the calibration of high-temperature fiber-optic microbend pressure transducers, and interferometric sensors for dc measurands. Other topics include the recognition of colors and collision avoidance in robotics using optical fiber sensors, the loss compensation of intensity-modulating fiber-optic sensors, and an embedded optical fiber strain tensor for composite structure applications.

Security Techniques for Sensor Systems and the Internet of Things

ERIC Educational Resources Information Center

Midi, Daniele

2016-01-01

Sensor systems are becoming pervasive in many domains, and are recently being generalized by the Internet of Things (IoT). This wide deployment, however, presents significant security issues. We develop security techniques for sensor systems and IoT, addressing all security management phases. Prior to deployment, the nodes need to be hardened. We…

New characterization techniques for LSST sensors

DOE PAGES

Nomerotski, A.

2015-06-18

Fully depleted, thick CCDs with extended infra-red response have become the sensor of choice for modern sky surveys. The charge transport effects in the silicon and associated astrometric distortions could make mapping between the sky coordinates and sensor coordinates non-trivial, and limit the ultimate precision achievable with these sensors. Two new characterization techniques for the CCDs, which both could probe these issues, are discussed: x-ray flat fielding and imaging of pinhole arrays.

A Technique to Determine the Self-Noise of Seismic Sensors for Performance Screening

NASA Astrophysics Data System (ADS)

Rademacher, H.; Hart, D.; Guralp, C.

2012-04-01

Seismic noise affects the performance of a seismic sensor and is thereby a limiting factor for the detection threshold of monitoring networks. Among the various sources of noise, the intrinsic self-noise of a seismic sensor is most diffcult to determine, because it is mostly masked by natural and anthropogenic ground noise and is also affected by the noise characteristic of the digitizer. Here we present a new technique to determine the self-noise of a seismic system (digitizer + sensors). It is based on a method introduced by Sleeman et al. (2005) to test the noise performance of digitizers. We infer the self-noise of a triplet of identical sensors by comparing coherent waveforms over a wide spectral band across the set-up. We will show first results from a proof-of-concept study done in a vault near Albuquerque, New Mexico. We will show, how various methods of shielding the sensors affect the results of this technique. This method can also be used as a means of quality control during sensor production, because poorly performing sensors can easily be identified.

Artifact Noise Removal Techniques on Seismocardiogram Using Two Tri-Axial Accelerometers

PubMed Central

Luu, Loc; Dinh, Anh

2018-01-01

The aim of this study is on the investigation of motion noise removal techniques using two-accelerometer sensor system and various placements of the sensors on gentle movement and walking of the patients. A Wi-Fi based data acquisition system and a framework on Matlab are developed to collect and process data while the subjects are in motion. The tests include eight volunteers who have no record of heart disease. The walking and running data on the subjects are analyzed to find the minimal-noise bandwidth of the SCG signal. This bandwidth is used to design filters in the motion noise removal techniques and peak signal detection. There are two main techniques of combining signals from the two sensors to mitigate the motion artifact: analog processing and digital processing. The analog processing comprises analog circuits performing adding or subtracting functions and bandpass filter to remove artifact noises before entering the data acquisition system. The digital processing processes all the data using combinations of total acceleration and z-axis only acceleration. The two techniques are tested on three placements of accelerometer sensors including horizontal, vertical, and diagonal on gentle motion and walking. In general, the total acceleration and z-axis acceleration are the best techniques to deal with gentle motion on all sensor placements which improve average systolic signal-noise-ratio (SNR) around 2 times and average diastolic SNR around 3 times comparing to traditional methods using only one accelerometer. With walking motion, ADDER and z-axis acceleration are the best techniques on all placements of the sensors on the body which enhance about 7 times of average systolic SNR and about 11 times of average diastolic SNR comparing to only one accelerometer method. Among the sensor placements, the performance of horizontal placement of the sensors is outstanding comparing with other positions on all motions. PMID:29614821

Polyaniline nanowires-gold nanoparticles hybrid network based chemiresistive hydrogen sulfide sensor

NASA Astrophysics Data System (ADS)

Shirsat, Mahendra D.; Bangar, Mangesh A.; Deshusses, Marc A.; Myung, Nosang V.; Mulchandani, Ashok

2009-02-01

We report a sensitive, selective, and fast responding room temperature chemiresistive sensor for hydrogen sulfide detection and quantification using polyaniline nanowires-gold nanoparticles hybrid network. The sensor was fabricated by facile electrochemical technique. Initially, polyaniline nanowires with a diameter of 250-320 nm bridging the gap between a pair of microfabricated gold electrodes were synthesized using templateless electrochemical polymerization using a two step galvanostatic technique. Polyaniline nanowires were then electrochemically functionalized with gold nanoparticles using cyclic voltammetry technique. These chemiresistive sensors show an excellent limit of detection (0.1 ppb), wide dynamic range (0.1-100 ppb), and very good selectivity and reproducibility.

Stabilizing operation point technique based on the tunable distributed feedback laser for interferometric sensors

NASA Astrophysics Data System (ADS)

Mao, Xuefeng; Zhou, Xinlei; Yu, Qingxu

2016-02-01

We describe a stabilizing operation point technique based on the tunable Distributed Feedback (DFB) laser for quadrature demodulation of interferometric sensors. By introducing automatic lock quadrature point and wavelength periodically tuning compensation into an interferometric system, the operation point of interferometric system is stabilized when the system suffers various environmental perturbations. To demonstrate the feasibility of this stabilizing operation point technique, experiments have been performed using a tunable-DFB-laser as light source to interrogate an extrinsic Fabry-Perot interferometric vibration sensor and a diaphragm-based acoustic sensor. Experimental results show that good tracing of Q-point was effectively realized.

Displacement sensors using soft magnetostrictive alloys

NASA Astrophysics Data System (ADS)

Hristoforou, E.; Reilly, R. E.

1994-09-01

We report results on the response of a family of displacement sensors, which are based on the magentostrictive delay line (MDL) technique, using current conductors orthogonal to the MDL. Such sensing technique is based on the change of the magnetic circuit at the acoustic stress point of origin due to the displacement of a soft magnetic material above it. Integrated arrays of sensors can be obtained due to the acoustic delay line technique and they can be used as tactile arrays, digitizers or devices for medical applications (gait analysis etc.), while absence of hysteresis and low cost of manufacturing make them competent in this sector of sensor market.

Evaluation of eating and rumination behaviour in cows using a noseband pressure sensor

PubMed Central

2013-01-01

Background An automated technique for recording eating and rumination behaviour was evaluated in ten lactating Brown Swiss cows by comparing data obtained from a pressure sensor with data obtained via direct observation over a 24-hour period. The recording device involved a pressure sensor integrated in the noseband of a halter. The analysed variables included number and duration of individual rumination, eating and resting phases, total daily length of these phases and number of cuds chewed per day. Results Eating and rumination phases were readily differentiated based on characteristic pressure profiles. Chewing movements during rumination were regular and generated regular waveforms with uniform amplitudes, whereas eating generated irregular waveforms with variable amplitudes. There was complete or almost complete agreement and no significant differences between data obtained via direct observation and pressure sensor technique. Both methods yielded an average of 16 daily eating phases with a mean duration of 28.3 minutes. Total time spent eating was 445.0 minutes for direct observation and 445.4 minutes for the pressure sensor technique. Both techniques recorded an average of 13.3 rumination phases with a mean duration of 30.3 (direct observation) and of 30.2 (pressure sensor) minutes. Total time spent ruminating per day, number of cuds per day and chewing cycles per cud were 389.3 and 388.3 minutes, 410.1 and 410.0 and 60.0 and 60.3 for direct observation and pressure sensor technique, respectively. There was a significant difference between the two methods with respect to mean number of chewing cycles per day (24′669, direct observation vs. 24′751, pressure sensor, P < 0.05, paired t-test). There were strong correlations between the two recording methods with correlation coefficients ranging from 0.98 to 1.00. Conclusions The results confirmed that measurements of eating and rumination variables obtained via the pressure sensor technique are in excellent agreement with data obtained via direct observation. PMID:23941142

Sensor Web Dynamic Measurement Techniques and Adaptive Observing Strategies

NASA Technical Reports Server (NTRS)

Talabac, Stephen J.

2004-01-01

Sensor Web observing systems may have the potential to significantly improve our ability to monitor, understand, and predict the evolution of rapidly evolving, transient, or variable environmental features and events. This improvement will come about by integrating novel data collection techniques, new or improved instruments, emerging communications technologies and protocols, sensor mark-up languages, and interoperable planning and scheduling systems. In contrast to today's observing systems, "event-driven" sensor webs will synthesize real- or near-real time measurements and information from other platforms and then react by reconfiguring the platforms and instruments to invoke new measurement modes and adaptive observation strategies. Similarly, "model-driven" sensor webs will utilize environmental prediction models to initiate targeted sensor measurements or to use a new observing strategy. The sensor web concept contrasts with today's data collection techniques and observing system operations concepts where independent measurements are made by remote sensing and in situ platforms that do not share, and therefore cannot act upon, potentially useful complementary sensor measurement data and platform state information. This presentation describes NASA's view of event-driven and model-driven Sensor Webs and highlights several research and development activities at the Goddard Space Flight Center.

An experimental study on the effect of temperature on piezoelectric sensors for impedance-based structural health monitoring.

PubMed

Baptista, Fabricio G; Budoya, Danilo E; de Almeida, Vinicius A D; Ulson, Jose Alfredo C

2014-01-10

The electromechanical impedance (EMI) technique is considered to be one of the most promising methods for developing structural health monitoring (SHM) systems. This technique is simple to implement and uses small and inexpensive piezoelectric sensors. However, practical problems have hindered its application to real-world structures, and temperature effects have been cited in the literature as critical problems. In this paper, we present an experimental study of the effect of temperature on the electrical impedance of the piezoelectric sensors used in the EMI technique. We used 5H PZT (lead zirconate titanate) ceramic sensors, which are commonly used in the EMI technique. The experimental results showed that the temperature effects were strongly frequency-dependent, which may motivate future research in the SHM field.

Polydimethylsiloxane pressure sensors for force analysis in tension band wiring of the olecranon.

PubMed

Zens, Martin; Goldschmidtboeing, Frank; Wagner, Ferdinand; Reising, Kilian; Südkamp, Norbert P; Woias, Peter

2016-11-14

Several different surgical techniques are used in the treatment of olecranon fractures. Tension band wiring is one of the most preferred options by surgeons worldwide. The concept of this technique is to transform a tensile force into a compression force that adjoins two surfaces of a fractured bone. Currently, little is known about the resulting compression force within a fracture. Sensor devices are needed that directly transduce the compression force into a measurement quality. This allows the comparison of different surgical techniques. Ideally the sensor devices ought to be placed in the gap between the fractured segments. The design, development and characterization of miniaturized pressure sensors fabricated entirely from polydimethylsiloxane (PDMS) for a placement within a fracture is presented. The pressure sensors presented in this work are tested, calibrated and used in an experimental in vitro study. The pressure sensors are highly sensitive with an accuracy of approximately 3 kPa. A flexible fabrication process for various possible applications is described. The first in vitro study shows that using a single-twist or double-twist technique in tension band wiring of the olecranon has no significant effect on the resulting compression forces. The in vitro study shows the feasibility of the proposed measurement technique and the results of a first exemplary study.

Pyroelectric Energy Scavenging Techniques for Self-Powered Nuclear Reactor Wireless Sensor Networks

DOE PAGES

Hunter, Scott Robert; Lavrik, Nickolay V; Datskos, Panos G; ...

2014-11-01

Recent advances in technologies for harvesting waste thermal energy from ambient environments present an opportunity to implement truly wireless sensor nodes in nuclear power plants. These sensors could continue to operate during extended station blackouts and during periods when operation of the plant s internal power distribution system has been disrupted. The energy required to power the wireless sensors must be generated using energy harvesting techniques from locally available energy sources, and the energy consumption within the sensor circuitry must therefore be low to minimize power and hence the size requirements of the energy harvester. Harvesting electrical energy from thermalmore » energy sources can be achieved using pyroelectric or thermoelectric conversion techniques. Recent modeling and experimental studies have shown that pyroelectric techniques can be cost competitive with thermoelectrics in self powered wireless sensor applications and, using new temperature cycling techniques, has the potential to be several times as efficient as thermoelectrics under comparable operating conditions. The development of a new thermal energy harvester concept, based on temperature cycled pyroelectric thermal-to-electrical energy conversion, is outlined. This paper outlines the modeling of cantilever and pyroelectric structures and single element devices that demonstrate the potential of this technology for the development of high efficiency thermal-to-electrical energy conversion devices.« less

Pyroelectric Energy Scavenging Techniques for Self-Powered Nuclear Reactor Wireless Sensor Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, Scott Robert; Lavrik, Nickolay V; Datskos, Panos G

Recent advances in technologies for harvesting waste thermal energy from ambient environments present an opportunity to implement truly wireless sensor nodes in nuclear power plants. These sensors could continue to operate during extended station blackouts and during periods when operation of the plant s internal power distribution system has been disrupted. The energy required to power the wireless sensors must be generated using energy harvesting techniques from locally available energy sources, and the energy consumption within the sensor circuitry must therefore be low to minimize power and hence the size requirements of the energy harvester. Harvesting electrical energy from thermalmore » energy sources can be achieved using pyroelectric or thermoelectric conversion techniques. Recent modeling and experimental studies have shown that pyroelectric techniques can be cost competitive with thermoelectrics in self powered wireless sensor applications and, using new temperature cycling techniques, has the potential to be several times as efficient as thermoelectrics under comparable operating conditions. The development of a new thermal energy harvester concept, based on temperature cycled pyroelectric thermal-to-electrical energy conversion, is outlined. This paper outlines the modeling of cantilever and pyroelectric structures and single element devices that demonstrate the potential of this technology for the development of high efficiency thermal-to-electrical energy conversion devices.« less

Sensor Fusion Techniques for Phased-Array Eddy Current and Phased-Array Ultrasound Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arrowood, Lloyd F.

Sensor (or Data) fusion is the process of integrating multiple data sources to produce more consistent, accurate and comprehensive information than is provided by a single data source. Sensor fusion may also be used to combine multiple signals from a single modality to improve the performance of a particular inspection technique. Industrial nondestructive testing may utilize multiple sensors to acquire inspection data depending upon the object under inspection and the anticipated types of defects that can be identified. Sensor fusion can be performed at various levels of signal abstraction with each having its strengths and weaknesses. A multimodal data fusionmore » strategy first proposed by Heideklang and Shokouhi that combines spatially scattered detection locations to improve detection performance of surface-breaking and near-surface cracks in ferromagnetic metals is shown using a surface inspection example and is then extended for volumetric inspections. Utilizing data acquired from an Olympus Omniscan MX2 from both phased array eddy current and ultrasound probes on test phantoms, single and multilevel fusion techniques are employed to integrate signals from the two modalities. Preliminary results demonstrate how confidence in defect identification and interpretation benefit from sensor fusion techniques. Lastly, techniques for integrating data into radiographic and volumetric imagery from computed tomography are described and results are presented.« less

Absolute pressure transducers for space shuttle and orbiter propulsion and control systems

NASA Technical Reports Server (NTRS)

Bolta, J. J.

1974-01-01

A preliminary design was completed, reviewing of such subjects as: the trade studies for media isolation and one sensor vs. two sensors for two bridges; compensation resistors; unit design; hydrogen embrittlement; sealing techniques and test station design. A design substantiation phase was finished, consisting of testing of a prototype unit and fabrication technique studies. A cryogenic test station was implemented and prototype sensor cells were fabricated, sensors assembled, and cryogenic tests performed.

Sensors research and technology

NASA Technical Reports Server (NTRS)

Cutts, James A.

1988-01-01

Information on sensors research and technology is given in viewgraph form. Information is given on sensing techniques for space science, passive remote sensing techniques and applications, submillimeter coherent sensing, submillimeter mixers and local oscillator sources, non-coherent sensors, active remote sensing, solid state laser development, a low vibration cooler, separation of liquid helium and vapor phase in zero gravity, and future plans.

An In-Process Surface Roughness Recognition System in End Milling Operations

ERIC Educational Resources Information Center

Yang, Lieh-Dai; Chen, Joseph C.

2004-01-01

To develop an in-process quality control system, a sensor technique and a decision-making algorithm need to be applied during machining operations. Several sensor techniques have been used in the in-process prediction of quality characteristics in machining operations. For example, an accelerometer sensor can be used to monitor the vibration of…

Ground Vibration Test Planning and Pre-Test Analysis for the X-33 Vehicle

NASA Technical Reports Server (NTRS)

Bedrossian, Herand; Tinker, Michael L.; Hidalgo, Homero

2000-01-01

This paper describes the results of the modal test planning and the pre-test analysis for the X-33 vehicle. The pre-test analysis included the selection of the target modes, selection of the sensor and shaker locations and the development of an accurate Test Analysis Model (TAM). For target mode selection, four techniques were considered, one based on the Modal Cost technique, one based on Balanced Singular Value technique, a technique known as the Root Sum Squared (RSS) method, and a Modal Kinetic Energy (MKE) approach. For selecting sensor locations, four techniques were also considered; one based on the Weighted Average Kinetic Energy (WAKE), one based on Guyan Reduction (GR), one emphasizing engineering judgment, and one based on an optimum sensor selection technique using Genetic Algorithm (GA) search technique combined with a criteria based on Hankel Singular Values (HSV's). For selecting shaker locations, four techniques were also considered; one based on the Weighted Average Driving Point Residue (WADPR), one based on engineering judgment and accessibility considerations, a frequency response method, and an optimum shaker location selection based on a GA search technique combined with a criteria based on HSV's. To evaluate the effectiveness of the proposed sensor and shaker locations for exciting the target modes, extensive numerical simulations were performed. Multivariate Mode Indicator Function (MMIF) was used to evaluate the effectiveness of each sensor & shaker set with respect to modal parameter identification. Several TAM reduction techniques were considered including, Guyan, IRS, Modal, and Hybrid. Based on a pre-test cross-orthogonality checks using various reduction techniques, a Hybrid TAM reduction technique was selected and was used for all three vehicle fuel level configurations.

CMOS: Efficient Clustered Data Monitoring in Sensor Networks

PubMed Central

2013-01-01

Tiny and smart sensors enable applications that access a network of hundreds or thousands of sensors. Thus, recently, many researchers have paid attention to wireless sensor networks (WSNs). The limitation of energy is critical since most sensors are battery-powered and it is very difficult to replace batteries in cases that sensor networks are utilized outdoors. Data transmission between sensor nodes needs more energy than computation in a sensor node. In order to reduce the energy consumption of sensors, we present an approximate data gathering technique, called CMOS, based on the Kalman filter. The goal of CMOS is to efficiently obtain the sensor readings within a certain error bound. In our approach, spatially close sensors are grouped as a cluster. Since a cluster header generates approximate readings of member nodes, a user query can be answered efficiently using the cluster headers. In addition, we suggest an energy efficient clustering method to distribute the energy consumption of cluster headers. Our simulation results with synthetic data demonstrate the efficiency and accuracy of our proposed technique. PMID:24459444

CMOS: efficient clustered data monitoring in sensor networks.

PubMed

Min, Jun-Ki

2013-01-01

Tiny and smart sensors enable applications that access a network of hundreds or thousands of sensors. Thus, recently, many researchers have paid attention to wireless sensor networks (WSNs). The limitation of energy is critical since most sensors are battery-powered and it is very difficult to replace batteries in cases that sensor networks are utilized outdoors. Data transmission between sensor nodes needs more energy than computation in a sensor node. In order to reduce the energy consumption of sensors, we present an approximate data gathering technique, called CMOS, based on the Kalman filter. The goal of CMOS is to efficiently obtain the sensor readings within a certain error bound. In our approach, spatially close sensors are grouped as a cluster. Since a cluster header generates approximate readings of member nodes, a user query can be answered efficiently using the cluster headers. In addition, we suggest an energy efficient clustering method to distribute the energy consumption of cluster headers. Our simulation results with synthetic data demonstrate the efficiency and accuracy of our proposed technique.

Modification of ruminal fermentation and methane production by adding legumes containing condensed tannins to an orchardgrass diet in continuous culture systems

USDA-ARS?s Scientific Manuscript database

Condensed tannins (CT) can alter ruminal fermentation and enteric methane (CH4) production in ruminants; however, research is lacking on how increased CT levels affect nutrient digestibility, volatile fatty acid (VFA) production, bacterial protein synthesis, fatty acid (FA) profiles, protozoal popul...

Host-rumen microbe interactions may be leveraged to improve the productivity of dairy cows

USDA-ARS?s Scientific Manuscript database

The cattle rumen serves as a digestive bioreactor for the dairy cow, yet our knowledge of the microbial contents, ecology, and host selection within the rumen is only precursory. This is despite the knowledge that the volatile fatty acids (VFA) and microbial crude protein (MCP) produced by rumen mic...

Redox mediators modify end product distribution in biomass fermentations by mixed ruminal microbes in vitro

USDA-ARS?s Scientific Manuscript database

The fermentation system of mixed ruminal bacteria is capable of generating large amounts of short-chain volatile fatty acids (VFA) via the carboxylate platform in vitro. These VFAs are subject to elongation to larger, more energy-dense products through reverse beta-oxidation. This study examined the...

Enteric methane production and ruminal fermentation of forage brassica diets fed in continuous culture

USDA-ARS?s Scientific Manuscript database

The aim of the current study was to determine nutrient digestibility, VFA production, N metabolism, and CH4 production of canola (Brassica napus L.), rapeseed (B. napus L.), turnip (B. rapa L.), and annual ryegrass (Lolium multiflorum Lam.) fed with orchardgrass (Dactylis glomerata L.) in continuous...

In Situ Biogeochemical Treatment Demonstration: Lessons Learned from ESTCP Project ER 201124

DTIC Science & Technology

2015-12-09

vegetable oil fermentation to volatile fatty acids (VFA) also likely reduced the pH and this change could have reduced the FeS reactivity. 2.3.5...Initially about 6.5 ● Vegetable oil fermentation to VFAs ● Lower FeSx reactivity Need to balance iron and sulfur! 55 Critical Factors

Effect of summer annuals on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

Summer annuals (SA) provide forage during the summer “forage slump”, yet research on ruminal fermentation and CH4 output of SA is lacking. A 4-unit, dual-flow continuous culture fermentor system was used to assess nutrient digestibility, VFA production, bacterial protein synthesis, and CH4 output of...

Displacement sensors using soft magnetostrictive alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hristoforou, E.; Reilly, R.E.

1994-09-01

The authors report results on the response of a family of displacement sensors, which are based on the magnetostrictive delay line (MDL) technique, using current conductor orthogonal to the MDL. Such sensing technique is based on the change of the magnetic circuit and the acoustic stress point of origin due to the displacement of a soft magnetic material above it. Integrated arrays of sensors can be obtained due to the acoustic delay line technique and they can be used as tactile arrays, digitizers or devices for medical application (gait analysis etc.), while absence of hysteresis and low cost of manufacturingmore » make them competent in this sector of sensor market.« less

Flexible Plasmonic Sensors

PubMed Central

Shir, Daniel; Ballard, Zachary S.; Ozcan, Aydogan

2016-01-01

Mechanical flexibility and the advent of scalable, low-cost, and high-throughput fabrication techniques have enabled numerous potential applications for plasmonic sensors. Sensitive and sophisticated biochemical measurements can now be performed through the use of flexible plasmonic sensors integrated into existing medical and industrial devices or sample collection units. More robust sensing schemes and practical techniques must be further investigated to fully realize the potentials of flexible plasmonics as a framework for designing low-cost, embedded and integrated sensors for medical, environmental, and industrial applications. PMID:27547023

Wireless passive radiation sensor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfeifer, Kent B; Rumpf, Arthur N; Yelton, William G

2013-12-03

A novel measurement technique is employed using surface acoustic wave (SAW) devices, passive RF, and radiation-sensitive films to provide a wireless passive radiation sensor that requires no batteries, outside wiring, or regular maintenance. The sensor is small (<1 cm.sup.2), physically robust, and will operate unattended for decades. In addition, the sensor can be insensitive to measurement position and read distance due to a novel self-referencing technique eliminating the need to measure absolute responses that are dependent on RF transmitter location and power.

Production of poly(hydroxybutyrate-hydroxyvalerate) from waste organics by the two-stage process: focus on the intermediate volatile fatty acids.

PubMed

Shen, Liang; Hu, Hongyou; Ji, Hongfang; Cai, Jiyuan; He, Ning; Li, Qingbiao; Wang, Yuanpeng

2014-08-01

The two-stage process, coupling volatile fatty acids (VFAs) fermentation and poly(hydroxybutyrate-hydroxyvalerate) (P(HB/HV)) biosynthesis, was investigated for five waste organic materials. The overall conversion efficiencies were glycerol>starch>molasses>waste sludge>protein, meanwhile the maximum P(HB/HV) (1.674 g/L) was obtained from waste starch. Altering the waste type brought more effects on VFAs composition other than the yield in the first stage, which in turn greatly changed the yield in the second stage. Further study showed that even-number carbon VFAs (or odd-number ones) had a good positive linear relationship with P(HB/HV) content of HB (or HV). Additionally, VFA producing microbiota was analyzed by pyrosequencing methods for five wastes, which indicated that specific species (e.g., Lactobacillus for protein; Ethanoligenens for starch; Ruminococcus and Limnobacter for glycerol) were dominant in the community for VFAs production. Potential competition among acidogenic bacteria specially involved to produce some VFA was proposed as well. Copyright © 2014 Elsevier Ltd. All rights reserved.

Use of submerged anaerobic membrane bioreactor (SAMBR) containing powdered activated carbon (PAC) for the treatment of textile effluents.

PubMed

Baêta, B E L; Ramos, R L; Lima, D R S; Aquino, S F

2012-01-01

This work investigated the use of submerged anaerobic membrane bioreactors (SAMBRs) in the presence and absence of powdered activated carbon (PAC) for the treatment of genuine textile wastewater. The reactors were operated at 35 °C with an HRT of 24 h and the textile effluent was diluted (1:10) with nutrient solution containing yeast extract as the source of the redox mediation riboflavin. The results showed that although both SAMBRs exhibited an excellent performance, the presence of PAC inside SAMBR-1 enhanced reactor stability and removal efficiency of chemical oxygen demand (COD), volatile fatty acids (VFA), turbidity and color. The median removal efficiencies of COD and color in SAMBR-1 were, 90 and 94% respectively; whereas for SAMBR-2 (without PAC) these values were 79 and 86%, In addition, the median values of turbidity and VFA were 8 NTU and 8 mg/L for SAMBR-1 and 14 NTU and 26 mg/L for SAMBR-2, indicating that the presence of PAC inside SAMBR-1 led to the production of an anaerobic effluent of high quality regarding such parameters.

Hydrolysis-acidogenesis of food waste in solid-liquid-separating continuous stirred tank reactor (SLS-CSTR) for volatile organic acid production.

PubMed

Karthikeyan, Obulisamy Parthiba; Selvam, Ammaiyappan; Wong, Jonathan W C

2016-01-01

The use of conventional continuous stirred tank reactor (CSTR) can affect the methane (CH4) recovery in a two-stage anaerobic digestion of food waste (FW) due to carbon short circuiting in the hydrolysis-acidogenesis (Hy-Aci) stage. In this research, we have designed and tested a solid-liquid-separating CSTR (SLS-CSTR) for effective Hy-Aci of FW. The working conditions were pH 6 and 9 (SLS-CSTR-1 and -2, respectively); temperature-37°C; agitation-300rpm; and organic loading rate (OLR)-2gVSL(-1)day(-1). The volatile fatty acids (VFA), enzyme activities and bacterial population (by qPCR) were determined as test parameters. Results showed that the Hy-Aci of FW at pH 9 produced ∼35% excess VFA as compared to that at pH 6, with acetic and butyric acids as major precursors, which correlated with the high enzyme activities and low lactic acid bacteria. The design provided efficient solid-liquid separation there by improved the organic acid yields from FW. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comprehensive monitoring and management of a long-term thermophilic CSTR treating coffee grounds, coffee liquid, milk waste, and municipal sludge.

PubMed

Shofie, Mohammad; Qiao, Wei; Li, Qian; Takayanagi, Kazuyuki; Li, Yu-You

2015-09-01

The CSTR process has previously not been successfully applied to treat coffee residues under thermophilic temperature and long term operation. In this experiment, the CSTR was fed with mixture substrate (TS ∼ 70 g/L) of coffee grounds, coffee wastewater, milk waste and municipal sludge and it was operated under 55 °C for 225 days. A steady state was achieved under HRT 30 days and OLR 4.0 kg-COD/m(3)/d. However, there was an 35 days inhibition with VFA accumulation (propionic acid 700-1900 mg/L) when doubling the OLR by shortening HRT to 15 days. But, an addition of microelements and sulfate (0.5 g/L) in feedstock increased reactor resilience and stability under high loading rate and propionic acid stress. Continuous monitoring of hydrogen in biogas indicated the imbalance of acetogenesis. The effectiveness of comprehensive parameters (total VFA, propionic acid, IA/PA, IA/TA and CH4 content) was proved to manage the thermophilic system. Copyright © 2015 Elsevier Ltd. All rights reserved.

High-solid Anaerobic Co-digestion of Sewage Sludge and Cattle Manure: The Effects of Volatile Solid Ratio and pH

PubMed Central

Dai, Xiaohu; Chen, Yang; Zhang, Dong; Yi, Jing

2016-01-01

High-solid anaerobic digestion is an attractive solution to the problem of sewage sludge disposal. One method that can be used to enhance the production of volatile fatty acids (VFAs) and the generation of methane from anaerobic digestion involves combining an alkaline pretreatment step with the synergistic effects of sewage sludge and cattle manure co-digestion, which improves the activity of key enzymes and microorganisms in the anaerobic co-digestion system to promote the digestion of organic waste. In this study, we describe an efficient strategy that involves adjusting the volatile solid (VS) ratio (sewage sludge/cattle manure: 3/7) and initial pH (9.0) to improve VFA production and methane generation from the co-digestion of sludge and manure. The experimental results indicate that the maximum VFA production was 98.33 g/kg-TS (total solid) at the optimal conditions. Furthermore, methane generation in a long-term semi-continuously operated reactor (at a VS ratio of 3/7 and pH of 9.0) was greater than 120.0 L/kg-TS. PMID:27725704

Slice profile effects in 2D slice-selective MRI of hyperpolarized nuclei.

PubMed

Deppe, Martin H; Teh, Kevin; Parra-Robles, Juan; Lee, Kuan J; Wild, Jim M

2010-02-01

This work explores slice profile effects in 2D slice-selective gradient-echo MRI of hyperpolarized nuclei. Two different sequences were investigated: a Spoiled Gradient Echo sequence with variable flip angle (SPGR-VFA) and a balanced Steady-State Free Precession (SSFP) sequence. It is shown that in SPGR-VFA the distribution of flip angles across the slice present in any realistically shaped radiofrequency (RF) pulse leads to large excess signal from the slice edges in later RF views, which results in an undesired non-constant total transverse magnetization, potentially exceeding the initial value by almost 300% for the last RF pulse. A method to reduce this unwanted effect is demonstrated, based on dynamic scaling of the slice selection gradient. SSFP sequences with small to moderate flip angles (<40 degrees ) are also shown to preserve the slice profile better than the most commonly used SPGR sequence with constant flip angle (SPGR-CFA). For higher flip angles, the slice profile in SSFP evolves in a manner similar to SPGR-CFA, with depletion of polarization in the center of the slice. Copyright 2009 Elsevier Inc. All rights reserved.

Pre-aeration of food waste to augment acidogenic process at higher organic load: Valorizing biohydrogen, volatile fatty acids and biohythane.

PubMed

Sarkar, Omprakash; Venkata Mohan, S

2017-10-01

Application of pre-aeration (AS) to waste prior to feeding was evaluated on acidogenic process in a semi-pilot scale biosystem for the production of biobased products (biohydrogen, volatile fatty acids (VFA) and biohythane) from food waste. Oxygen assisted in pre-hydrolysis of waste along with the suppression of methanogenic activity resulting in enhanced acidogenic product formation. AS operation resulted in 97% improvement in hydrogen conversion efficiency (HCE) and 10% more VFA production than the control. Increasing the organic load (OL) of food waste in association with AS application improved the productivity. The application of AS also influenced concentration and composition of fatty acid. Highest fraction of acetic (5.3g/l), butyric (0.7g/l) and propionic acid (0.84g/l) was achieved at higher OL (100g COD/l) with good degree of acidification (DOA). AS strategy showed positive influence on biofuel (biohydrogen and biohythane) production along with the biosynthesis of short chain fatty acids functioning as a low-cost pretreatment strategy in a single stage bioprocess. Copyright © 2017 Elsevier Ltd. All rights reserved.

Selective simplification and reinforcement of microbial community in autothermal thermophilic aerobic digestion to enhancing stabilization process of sewage sludge by conditioning with ferric nitrate.

PubMed

Jin, Ningben; Shou, Zongqi; Yuan, Haiping; Lou, Ziyang; Zhu, Nanwen

2016-03-01

The effect of ferric nitrate on microbial community and enhancement of stabilization process for sewage sludge was investigated in autothermal thermophilic aerobic digestion. The disinhibition of volatile fatty acids (VFA) was obtained with alteration of individual VFA concentration order. Bacterial taxonomic identification by 454 high-throughput pyrosequencing found the dominant phylum Proteobacteria in non-dosing group was converted to phylum Firmicutes in dosing group after ferric nitrate added and simplification of bacteria phylotypes was achieved. The preponderant Tepidiphilus sp. vanished, and Symbiobacterium sp. and Tepidimicrobium sp. were the most advantageous phylotypes with conditioning of ferric nitrate. Consequently, biodegradable substances in dissolved organic matters increased, which contributed to the favorable environment for microbial metabolism and resulted in acceleration of sludge stabilization. Ultimately, higher stabilization level was achieved as ratio of soluble chemical oxygen demand to total chemical oxygen demand (TCOD) decreased while TCOD reduced as well in dosing group comparing to non-dosing group. Copyright © 2016 Elsevier Ltd. All rights reserved.

Converting the organic fraction of solid waste from the city of Abu Dhabi to valuable products via dark fermentation--Economic and energy assessment.

PubMed

Bonk, Fabian; Bastidas-Oyanedel, Juan-Rodrigo; Schmidt, Jens Ejbye

2015-06-01

Landfilling the organic fraction of municipal solid waste (OFMSW) leads to greenhouse gas emissions and loss of valuable resources. Sustainable and cost efficient solutions need to be developed to solve this problem. This study evaluates the feasibility of using dark fermentation (DF) to convert the OFMSW to volatile fatty acids (VFAs), fertilizer and H2. The VFAs in the DF effluent can be used directly as substrate for subsequent bioprocesses or purified from the effluent for industrial use. DF of the OFMSW in Abu Dhabi will be economically sustainable once VFA purification can be accomplished on large scale for less than 15USD/m(3)(effluent). With a VFA minimum selling price of 330 USD/tCOD, DF provides a competitive carbon source to sugar. Furthermore, DF is likely to use less energy than conventional processes that produce VFAs, fertilizer and H2. This makes DF of OFMSW a promising waste treatment technology and biorefinery platform. Copyright © 2015 Elsevier Ltd. All rights reserved.

High-solid Anaerobic Co-digestion of Sewage Sludge and Cattle Manure: The Effects of Volatile Solid Ratio and pH

NASA Astrophysics Data System (ADS)

Dai, Xiaohu; Chen, Yang; Zhang, Dong; Yi, Jing

2016-10-01

High-solid anaerobic digestion is an attractive solution to the problem of sewage sludge disposal. One method that can be used to enhance the production of volatile fatty acids (VFAs) and the generation of methane from anaerobic digestion involves combining an alkaline pretreatment step with the synergistic effects of sewage sludge and cattle manure co-digestion, which improves the activity of key enzymes and microorganisms in the anaerobic co-digestion system to promote the digestion of organic waste. In this study, we describe an efficient strategy that involves adjusting the volatile solid (VS) ratio (sewage sludge/cattle manure: 3/7) and initial pH (9.0) to improve VFA production and methane generation from the co-digestion of sludge and manure. The experimental results indicate that the maximum VFA production was 98.33 g/kg-TS (total solid) at the optimal conditions. Furthermore, methane generation in a long-term semi-continuously operated reactor (at a VS ratio of 3/7 and pH of 9.0) was greater than 120.0 L/kg-TS.

Production of co-polymers of polyhydroxyalkanoates by regulating the hydrolysis of biowastes.

PubMed

Kumar, Prasun; Ray, Subhasree; Kalia, Vipin C

2016-01-01

Production of polyhydroxyalkanoate (PHA) co-polymers by Bacillus spp. was studied by feeding defined volatile fatty acids (VFAs) obtained through controlled hydrolysis of various wastes. Eleven mixed hydrolytic cultures (MHCs) each containing 6 strains could generate VFA from slurries of (2% total solids): pea-shells (PS), potato peels (PP), apple pomace (AP) and onion peels (OP). PS hydrolysates (obtained with MHC2 and MHC5) inoculated with Bacillus cereus EGU43 and Bacillus thuringiensis EGU45 produced co-polymers of PHA at the rate of 15-60mg/L with a 3HV content of 1%w/w. An enhancement in PHA yield of 3.66-fold, i.e. 205-550mg/L with 3HV content up to 7.5%(w/w) was observed upon addition of OP hydrolysate and 1% glucose (w/v) to PS hydrolysates. This is the first demonstration, where PHA co-polymer composition, under non-axenic conditions, could be controlled by customizing VFA profile of the hydrolysate by the addition of different biowastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Production of polyhydroxyalkanoates (PHA) by bacterial consortium from excess sludge fermentation liquid at laboratory and pilot scales.

PubMed

Jia, Qianqian; Xiong, Huilei; Wang, Hui; Shi, Hanchang; Sheng, Xinying; Sun, Run; Chen, Guoqiang

2014-11-01

The generation of polyhydroxyalkanoates (PHA) from excess sludge fermentation liquid (SFL) was studied at lab and pilot scale. A PHA-accumulated bacterial consortium (S-150) was isolated from activated sludge using simulated SFL (S-SFL) contained high concentration volatile fatty acids (VFA) and nitrogen. The maximal PHA content accounted for 59.18% in S-SFL and dropped to 23.47% in actual SFL (L-SFL) of the dry cell weight (DCW) at lab scale. The pilot-scale integrated system comprised an anaerobic fermentation reactor (AFR), a ceramic membrane system (CMS) and a PHA production bio-reactor (PHAR). The PHA content from pilot-scale SFL (P-SFL) finally reached to 59.47% DCW with the maximal PHA yield coefficient (YP/S) of 0.17 g PHA/g COD. The results indicated that VFA-containing SFL was suitable for PHA production. The adverse impact of excess nitrogen and non-VFAs in SFL might be eliminated by pilot-scale domestication, which might resulted in community structure optimization and substrate selective ability improvement of S-150. Copyright © 2014 Elsevier Ltd. All rights reserved.

Enhancement of acidogenic fermentation for volatile fatty acid production from food waste: Effect of redox potential and inoculum.

PubMed

Yin, Jun; Yu, Xiaoqin; Zhang, Yeer; Shen, Dongsheng; Wang, Meizhen; Long, Yuyang; Chen, Ting

2016-09-01

The aim of this study was to explore the effects of redox potential (ORP) and inoculum on volatile fatty acids (VFAs) production from food waste by acidogenic fermentation. Four experimental conditions with two ORP levels were tested: limited aeration conditions with ORP level of -100 to -200mV inoculating anaerobic sludge (LA+AnS) or aerobic sludge (LA+AeS), and anaerobic conditions with ORP level of -200 to -300mV inoculating anaerobic sludge with 2-bromoethanosulfophate (AN+BES) and without BES (AN). The maximal VFA yield (0.79g COD/g VS) was attained in LA+AnS reactor due to enhanced hydrolysis of substrates, especially proteins (degradation efficiency 78.3%). A higher frequency of phylum Firmicutes under limited aeration conditions (42.2-48.2%) was observed than that under anaerobic conditions (21.1%). The microbial community was more diverse in LA+AnS reactors than LA+AeS. We conclude that appropriate ORP level (from -100 to -200mV) and inoculum play essential roles in VFA production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Full-scale production of VFAs from sewage sludge by anaerobic alkaline fermentation to improve biological nutrients removal in domestic wastewater.

PubMed

Liu, He; Han, Peng; Liu, Hongbo; Zhou, Guangjie; Fu, Bo; Zheng, Zhiyong

2018-07-01

A full-scale project of thermal-alkaline pretreatment and alkaline fermentation of sewage sludge was built to produce volatile fatty acids (VFAs) which was then used as external carbon source for improving biological nitrogen and phosphorus removals (BNPR) in wastewater plant. Results showed this project had efficient and stable performances in VFA production, sludge reduce and BNPR. Hydrolysis rate in pretreatment, VFAs yield in fermentation and total VS reduction reached 68.7%, 261.32 mg COD/g VSS and 54.19%, respectively. Moreover, fermentation liquid with VFA presented similar efficiency as acetic acid in enhancing BNPR, obtaining removal efficiencies of nitrogen and phosphorus up to 72.39% and 89.65%, respectively. Finally, the project also presented greater economic advantage than traditional processes, and the net profits for VFAs and biogas productions are 9.12 and 3.71 USD/m 3 sludge, respectively. Long-term operation indicated that anaerobic alkaline fermentation for VFAs production is technically and economically feasible for sludge carbon recovery. Copyright © 2018 Elsevier Ltd. All rights reserved.

Inhibiting excessive acidification using zero-valent iron in anaerobic digestion of food waste at high organic load rates.

PubMed

Kong, Xin; Wei, Yonghong; Xu, Shuang; Liu, Jianguo; Li, Huan; Liu, Yili; Yu, Shuyao

2016-07-01

Excessive acidification occurs frequently in food waste (FW) anaerobic digestion (AD) due to the high carbon-to-nitrogen ratio of FW. In this study, zero-valent iron (ZVI) was applied to prevent the excessive acidification. All of the control groups, without ZVI addition (pH∼5.3), produced little methane (CH4) and had high volatile fatty acids/bicarbonate alkalinity (VFA/ALK). By contrast, at OLR of 42.32gVS/Lreactor, the pH of effluent from the reactors with 0.4g/gVSFWadded of ZVI increased to 7.8-8.2, VFA/ALK decreased to <0.1, and the final CH4 yield was ∼380mL/gVSFWadded, suggesting inhibition of excessive acidification. After adding powdered or scrap metal ZVI to the acidogenic reactors, the fractional content of butyric acid changed from 30-40% to 0%, while, that of acetic acid increased. These results indicate that adding ZVI to FW digestion at high OLRs could eliminate excessive acidification by promoting butyric acid conversion and enhancing methanogen activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microbial Production of Short Chain Fatty Acids from Lignocellulosic Biomass: Current Processes and Market.

PubMed

Baumann, Ivan; Westermann, Peter

2016-01-01

Biological production of organic acids from conversion of biomass derivatives has received increased attention among scientists and engineers and in business because of the attractive properties such as renewability, sustainability, degradability, and versatility. The aim of the present review is to summarize recent research and development of short chain fatty acids production by anaerobic fermentation of nonfood biomass and to evaluate the status and outlook for a sustainable industrial production of such biochemicals. Volatile fatty acids (VFAs) such as acetic acid, propionic acid, and butyric acid have many industrial applications and are currently of global economic interest. The focus is mainly on the utilization of pretreated lignocellulosic plant biomass as substrate (the carbohydrate route) and development of the bacteria and processes that lead to a high and economically feasible production of VFA. The current and developing market for VFA is analyzed focusing on production, prices, and forecasts along with a presentation of the biotechnology companies operating in the market for sustainable biochemicals. Finally, perspectives on taking sustainable product of biochemicals from promise to market introduction are reviewed.

Microbial Production of Short Chain Fatty Acids from Lignocellulosic Biomass: Current Processes and Market

PubMed Central

Baumann, Ivan

2016-01-01

Biological production of organic acids from conversion of biomass derivatives has received increased attention among scientists and engineers and in business because of the attractive properties such as renewability, sustainability, degradability, and versatility. The aim of the present review is to summarize recent research and development of short chain fatty acids production by anaerobic fermentation of nonfood biomass and to evaluate the status and outlook for a sustainable industrial production of such biochemicals. Volatile fatty acids (VFAs) such as acetic acid, propionic acid, and butyric acid have many industrial applications and are currently of global economic interest. The focus is mainly on the utilization of pretreated lignocellulosic plant biomass as substrate (the carbohydrate route) and development of the bacteria and processes that lead to a high and economically feasible production of VFA. The current and developing market for VFA is analyzed focusing on production, prices, and forecasts along with a presentation of the biotechnology companies operating in the market for sustainable biochemicals. Finally, perspectives on taking sustainable product of biochemicals from promise to market introduction are reviewed. PMID:27556042

Biogas by semi-continuous anaerobic digestion of food waste.

PubMed

Zhang, Cunsheng; Su, Haijia; Wang, Zhenbin; Tan, Tianwei; Qin, Peiyong

2015-04-01

The semi-continuous anaerobic digestion of food waste was investigated in 1-L and 20-L continuously stirred tank reactors (CSTRs), to identify the optimum operation condition and the methane production of the semi-continuous anaerobic process. Results from a 1-L digester indicated that the optimum organic loading rate (OLR) for semi-continuous digestion is 8 g VS/L/day. The corresponding methane yield and chemical oxygen demand (COD) reduction were 385 mL/g VS and 80.2 %, respectively. Anaerobic digestion was inhibited at high OLRs (12 and 16 g VS/L/day), due to volatile fatty acid (VFA) accumulation. Results from a 20-L digester indicated that a higher methane yield of 423 mL/g VS was obtained at this larger scale. The analysis showed that the methane production at the optimum OLR fitted well with the determined kinetics equation. An obvious decrease on the methane content was observed at the initial of digestion. The increased metabolization of microbes and the activity decrease of methanogen caused by VFA accumulation explained the lower methane content at the initial of digestion.

High-Temperature Piezoelectric Sensing

PubMed Central

Jiang, Xiaoning; Kim, Kyungrim; Zhang, Shujun; Johnson, Joseph; Salazar, Giovanni

2014-01-01

Piezoelectric sensing is of increasing interest for high-temperature applications in aerospace, automotive, power plants and material processing due to its low cost, compact sensor size and simple signal conditioning, in comparison with other high-temperature sensing techniques. This paper presented an overview of high-temperature piezoelectric sensing techniques. Firstly, different types of high-temperature piezoelectric single crystals, electrode materials, and their pros and cons are discussed. Secondly, recent work on high-temperature piezoelectric sensors including accelerometer, surface acoustic wave sensor, ultrasound transducer, acoustic emission sensor, gas sensor, and pressure sensor for temperatures up to 1,250 °C were reviewed. Finally, discussions of existing challenges and future work for high-temperature piezoelectric sensing are presented. PMID:24361928

Fiber optic sensors for corrosion detection

NASA Technical Reports Server (NTRS)

Smith, Alphonso C.

1993-01-01

The development of fiber optic sensors for the detection of a variety of material parameters has grown tremendously over the past several years. Additionally, the potential for analytical applications of fiber optic sensors have become more widely used. New pH sensors have also been developed using fiber optic techniques to detect fluorescence characteristics from immobilized fluorogenic reagent chemicals. The primary purpose of this research was to investigate the feasibility of using fiber optic sensors to detect the presence of Al(sup 3+) ions made in the process of environmental corrosion of aluminum materials. The Al(sup 3+) ions plus a variety of other type of metal ions can be detected using analytical techniques along with fiber optic sensors.

Detection and Monitoring of Toxic Chemical at Ultra Trace Level by Utilizing Doped Nanomaterial

PubMed Central

Khan, Sher Bahadar; Rahman, Mohammed M.; Akhtar, Kalsoom; Asiri, Abdullah M.

2014-01-01

Composite nanoparticles were synthesized by eco-friendly hydrothermal process and characterized by different spectroscopic techniques. All the spectroscopic techniques suggested the synthesis of well crystalline optically active composite nanoparticles with average diameter of ∼30 nm. The synthesized nanoparticles were applied for the development of chemical sensor which was fabricated by coating the nanoparticles on silver electrode for the recognition of phthalimide using simple I–V technique. The developed sensor exhibited high sensitivity (1.7361 µA.mM−1.cm−2), lower detection limit (8.0 µM) and long range of detection (77.0 µM to 0.38 M). Further the resistances of composite nanoparticles based sensor was found to be 2.7 MΩ which change from 2.7 to 1.7 with change in phthalimide concentration. The major advantages of the designed sensor over existing sensors are its simple technique, low cost, lower detection limit, high sensitivity and long range of detection. It can detect phthalimide even at trace level and sense over wide range of concentrations. Therefore the composite nanoparticals would be a better choice for the fabrication of phthalimide chemical sensor and would be time and cost substituted implement for environmental safety. PMID:25329666

Application of data fusion techniques and technologies for wearable health monitoring.

PubMed

King, Rachel C; Villeneuve, Emma; White, Ruth J; Sherratt, R Simon; Holderbaum, William; Harwin, William S

2017-04-01

Technological advances in sensors and communications have enabled discrete integration into everyday objects, both in the home and about the person. Information gathered by monitoring physiological, behavioural, and social aspects of our lives, can be used to achieve a positive impact on quality of life, health, and well-being. Wearable sensors are at the cusp of becoming truly pervasive, and could be woven into the clothes and accessories that we wear such that they become ubiquitous and transparent. To interpret the complex multidimensional information provided by these sensors, data fusion techniques are employed to provide a meaningful representation of the sensor outputs. This paper is intended to provide a short overview of data fusion techniques and algorithms that can be used to interpret wearable sensor data in the context of health monitoring applications. The application of these techniques are then described in the context of healthcare including activity and ambulatory monitoring, gait analysis, fall detection, and biometric monitoring. A snap-shot of current commercially available sensors is also provided, focusing on their sensing capability, and a commentary on the gaps that need to be bridged to bring research to market. Copyright © 2017. Published by Elsevier Ltd.

Optical control and diagnostics sensors for gas turbine machinery

NASA Astrophysics Data System (ADS)

Trolinger, James D.; Jenkins, Thomas P.; Heeg, Bauke

2012-10-01

There exists a vast range of optical techniques that have been under development for solving complex measurement problems related to gas-turbine machinery and phenomena. For instance, several optical techniques are ideally suited for studying fundamental combustion phenomena in laboratory environments. Yet other techniques hold significant promise for use as either on-line gas turbine control sensors, or as health monitoring diagnostics sensors. In this paper, we briefly summarize these and discuss, in more detail, some of the latter class of techniques, including phosphor thermometry, hyperspectral imaging and low coherence interferometry, which are particularly suited for control and diagnostics sensing on hot section components with ceramic thermal barrier coatings (TBCs).

Impact of pulse thermal processing on the properties of inkjet printed metal and flexible sensors

DOE PAGES

Joshi, Pooran C.; Kuruganti, Teja; Killough, Stephen M.

2015-03-11

In this paper, we report on the low temperature processing of environmental sensors employing pulse thermal processing (PTP) technique to define a path toward flexible sensor technology on plastic, paper, and fabric substrates. Inkjet printing and pulse thermal processing technique were used to realize mask-less, additive integration of low-cost sensors on polymeric substrates with specific focus on temperature, humidity, and strain sensors. The printed metal line performance was evaluated in terms of the electrical conductivity characteristics as a function of post-deposition thermal processing conditions. The PTP processed Ag metal lines exhibited high conductivity with metal sheet resistance values below 100more » mΩ/{whitesquare} using a pulse width as short as 250 μs. The flexible temperature and relative humidity sensors were defined on flexible polyimide substrates by direct printing of Ag metal structures. The printed resistive temperature sensor and capacitive humidity sensor were characterized for their sensitivity with focus on future smart-building applications. Strain gauges were printed on polyimide substrate to determine the mechanical properties of the silver nanoparticle films. Finally, the observed electrical properties of the printed metal lines and the sensitivity of the flexible sensors show promise for the realization of a high performance print-on-demand technology exploiting low thermal-budget PTP technique.« less

Automated Construction of Node Software Using Attributes in a Ubiquitous Sensor Network Environment

PubMed Central

Lee, Woojin; Kim, Juil; Kang, JangMook

2010-01-01

In sensor networks, nodes must often operate in a demanding environment facing restrictions such as restricted computing resources, unreliable wireless communication and power shortages. Such factors make the development of ubiquitous sensor network (USN) applications challenging. To help developers construct a large amount of node software for sensor network applications easily and rapidly, this paper proposes an approach to the automated construction of node software for USN applications using attributes. In the proposed technique, application construction proceeds by first developing a model for the sensor network and then designing node software by setting the values of the predefined attributes. After that, the sensor network model and the design of node software are verified. The final source codes of the node software are automatically generated from the sensor network model. We illustrate the efficiency of the proposed technique by using a gas/light monitoring application through a case study of a Gas and Light Monitoring System based on the Nano-Qplus operating system. We evaluate the technique using a quantitative metric—the memory size of execution code for node software. Using the proposed approach, developers are able to easily construct sensor network applications and rapidly generate a large number of node softwares at a time in a ubiquitous sensor network environment. PMID:22163678

Tapered Optical Fiber Functionalized with Palladium Nanoparticles by Drop Casting and Laser Radiation for H2 and Volatile Organic Compounds Sensing Purposes

PubMed Central

González-Sierra, Nancy Elizabeth; Gómez-Pavón, Luz del Carmen; Pérez-Sánchez, Gerardo Francisco; Luis-Ramos, Arnulfo; Zaca-Morán, Plácido; Chávez-Ramírez, Fernando

2017-01-01

A comparative study on the sensing properties of a tapered optical fiber pristine and functionalized with the palladium nanoparticles to hydrogen and volatile organic compounds (VOCs), is presented. The sensor response and, response/recovery times were extracted from the measurements of the transient response of the device. The tapered optical fiber sensor was fabricated using a single-mode optical fiber by the flame-brushing technique. Functionalization of the optical fiber was performed using an aqueous solution of palladium chloride by drop-casting technique assisted for laser radiation. The detection principle of the sensor is based on the changes in the optical properties of palladium nanoparticles when exposed to reducing gases, which causes a variation in the absorption of evanescent waves. A continuous wave laser diode operating at 1550 nm is used for the sensor characterization. The sensor functionalized with palladium nanoparticles by this technique is viable for the sensing of hydrogen and VOCs, since it shows an enhancement in sensor response and response time compared to the sensor based on the pristine optical microfiber. The results show that the fabricated sensor is competitive with other fiber optic sensors functionalized with palladium nanoparticles to the hydrogen. PMID:28878161

Strength and fatigue life evaluation of composite laminate with embedded sensors

NASA Astrophysics Data System (ADS)

Rathod, Vivek T.; Hiremath, S. R.; Roy Mahapatra, D.

2014-04-01

Prognosis regarding durability of composite structures using various Structural Health Monitoring (SHM) techniques is an important and challenging topic of research. Ultrasonic SHM systems with embedded transducers have potential application here due to their instant monitoring capability, compact packaging potential toward unobtrusiveness and noninvasiveness as compared to non-contact ultrasonic and eddy current techniques which require disassembly of the structure. However, embedded sensors pose a risk to the structure by acting as a flaw thereby reducing life. The present paper focuses on the determination of strength and fatigue life of the composite laminate with embedded film sensors like CNT nanocomposite, PVDF thin films and piezoceramic films. First, the techniques of embedding these sensors in composite laminates is described followed by the determination of static strength and fatigue life at coupon level testing in Universal Testing Machine (UTM). Failure mechanisms of the composite laminate with embedded sensors are studied for static and dynamic loading cases. The coupons are monitored for loading and failure using the embedded sensors. A comparison of the performance of these three types of embedded sensors is made to study their suitability in various applications. These three types of embedded sensors cover a wide variety of applications, and prove to be viable in embedded sensor based SHM of composite structures.

Automated construction of node software using attributes in a ubiquitous sensor network environment.

PubMed

Lee, Woojin; Kim, Juil; Kang, JangMook

2010-01-01

In sensor networks, nodes must often operate in a demanding environment facing restrictions such as restricted computing resources, unreliable wireless communication and power shortages. Such factors make the development of ubiquitous sensor network (USN) applications challenging. To help developers construct a large amount of node software for sensor network applications easily and rapidly, this paper proposes an approach to the automated construction of node software for USN applications using attributes. In the proposed technique, application construction proceeds by first developing a model for the sensor network and then designing node software by setting the values of the predefined attributes. After that, the sensor network model and the design of node software are verified. The final source codes of the node software are automatically generated from the sensor network model. We illustrate the efficiency of the proposed technique by using a gas/light monitoring application through a case study of a Gas and Light Monitoring System based on the Nano-Qplus operating system. We evaluate the technique using a quantitative metric-the memory size of execution code for node software. Using the proposed approach, developers are able to easily construct sensor network applications and rapidly generate a large number of node softwares at a time in a ubiquitous sensor network environment.

Tapered Optical Fiber Functionalized with Palladium Nanoparticles by Drop Casting and Laser Radiation for H₂ and Volatile Organic Compounds Sensing Purposes.

PubMed

González-Sierra, Nancy Elizabeth; Gómez-Pavón, Luz Del Carmen; Pérez-Sánchez, Gerardo Francisco; Luis-Ramos, Arnulfo; Zaca-Morán, Plácido; Muñoz-Pacheco, Jesús Manuel; Chávez-Ramírez, Francisco

2017-09-06

A comparative study on the sensing properties of a tapered optical fiber pristine and functionalized with the palladium nanoparticles to hydrogen and volatile organic compounds (VOCs), is presented. The sensor response and, response/recovery times were extracted from the measurements of the transient response of the device. The tapered optical fiber sensor was fabricated using a single-mode optical fiber by the flame-brushing technique. Functionalization of the optical fiber was performed using an aqueous solution of palladium chloride by drop-casting technique assisted for laser radiation. The detection principle of the sensor is based on the changes in the optical properties of palladium nanoparticles when exposed to reducing gases, which causes a variation in the absorption of evanescent waves. A continuous wave laser diode operating at 1550 nm is used for the sensor characterization. The sensor functionalized with palladium nanoparticles by this technique is viable for the sensing of hydrogen and VOCs, since it shows an enhancement in sensor response and response time compared to the sensor based on the pristine optical microfiber. The results show that the fabricated sensor is competitive with other fiber optic sensors functionalized with palladium nanoparticles to the hydrogen.

Signal processing for distributed sensor concept: DISCO

NASA Astrophysics Data System (ADS)

Rafailov, Michael K.

2007-04-01

Distributed Sensor concept - DISCO proposed for multiplication of individual sensor capabilities through cooperative target engagement. DISCO relies on ability of signal processing software to format, to process and to transmit and receive sensor data and to exploit those data in signal synthesis process. Each sensor data is synchronized formatted, Signal-to-Noise Ration (SNR) enhanced and distributed inside of the sensor network. Signal processing technique for DISCO is Recursive Adaptive Frame Integration of Limited data - RAFIL technique that was initially proposed [1] as a way to improve the SNR, reduce data rate and mitigate FPA correlated noise of an individual sensor digital video-signal processing. In Distributed Sensor Concept RAFIL technique is used in segmented way, when constituencies of the technique are spatially and/or temporally separated between transmitters and receivers. Those constituencies include though not limited to two thresholds - one is tuned for optimum probability of detection, the other - to manage required false alarm rate, and limited frame integration placed somewhere between the thresholds as well as formatters, conventional integrators and more. RAFIL allows a non-linear integration that, along with SNR gain, provides system designers more capability where cost, weight, or power considerations limit system data rate, processing, or memory capability [2]. DISCO architecture allows flexible optimization of SNR gain, data rates and noise suppression on sensor's side and limited integration, re-formatting and final threshold on node's side. DISCO with Recursive Adaptive Frame Integration of Limited data may have flexible architecture that allows segmenting the hardware and software to be best suitable for specific DISCO applications and sensing needs - whatever it is air-or-space platforms, ground terminals or integration of sensors network.

Objective measures, sensors and computational techniques for stress recognition and classification: a survey.

PubMed

Sharma, Nandita; Gedeon, Tom

2012-12-01

Stress is a major growing concern in our day and age adversely impacting both individuals and society. Stress research has a wide range of benefits from improving personal operations, learning, and increasing work productivity to benefiting society - making it an interesting and socially beneficial area of research. This survey reviews sensors that have been used to measure stress and investigates techniques for modelling stress. It discusses non-invasive and unobtrusive sensors for measuring computed stress, a term we coin in the paper. Sensors that do not impede everyday activities that could be used by those who would like to monitor stress levels on a regular basis (e.g. vehicle drivers, patients with illnesses linked to stress) is the focus of the discussion. Computational techniques have the capacity to determine optimal sensor fusion and automate data analysis for stress recognition and classification. Several computational techniques have been developed to model stress based on techniques such as Bayesian networks, artificial neural networks, and support vector machines, which this survey investigates. The survey concludes with a summary and provides possible directions for further computational stress research. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

A Data-Driven Response Virtual Sensor Technique with Partial Vibration Measurements Using Convolutional Neural Network.

PubMed

Sun, Shan-Bin; He, Yuan-Yuan; Zhou, Si-Da; Yue, Zhen-Jiang

2017-12-12

Measurement of dynamic responses plays an important role in structural health monitoring, damage detection and other fields of research. However, in aerospace engineering, the physical sensors are limited in the operational conditions of spacecraft, due to the severe environment in outer space. This paper proposes a virtual sensor model with partial vibration measurements using a convolutional neural network. The transmissibility function is employed as prior knowledge. A four-layer neural network with two convolutional layers, one fully connected layer, and an output layer is proposed as the predicting model. Numerical examples of two different structural dynamic systems demonstrate the performance of the proposed approach. The excellence of the novel technique is further indicated using a simply supported beam experiment comparing to a modal-model-based virtual sensor, which uses modal parameters, such as mode shapes, for estimating the responses of the faulty sensors. The results show that the presented data-driven response virtual sensor technique can predict structural response with high accuracy.

Analysis and optimal design of moisture sensor for rice grain moisture measurement

NASA Astrophysics Data System (ADS)

Jain, Sweety; Mishra, Pankaj Kumar; Thakare, Vandana Vikas

2018-04-01

The analysis and design of a microstrip sensor for accurate determination of moisture content (MC) in rice grains based on oven drying technique, this technique is easy, fast and less time-consuming to other techniques. The sensor is designed with low insertion loss, reflection coefficient and maximum gain is -35dB and 5.88dB at 2.68GHz as well as discussed all the parameters such as axial ratio, maximum gain, smith chart etc, which is helpful for analysis the moisture measurement. The variation in percentage of moisture measurement with magnitude and phase of transmission coefficient is investigated at selected frequencies. The microstrip moisture sensor consists of one layer: substrate FR4, thickness 1.638 is simulated by computer simulated technology microwave studio (CST MWS). It is concluded that the proposed sensor is suitable for development as a complete sensor and to estimate the optimum moisture content of rice grains with accurately, sensitivity, compact, versatile and suitable for determining the moisture content of other crops and agriculture products.

A Data-Driven Response Virtual Sensor Technique with Partial Vibration Measurements Using Convolutional Neural Network

PubMed Central

Sun, Shan-Bin; He, Yuan-Yuan; Zhou, Si-Da; Yue, Zhen-Jiang

2017-01-01

Measurement of dynamic responses plays an important role in structural health monitoring, damage detection and other fields of research. However, in aerospace engineering, the physical sensors are limited in the operational conditions of spacecraft, due to the severe environment in outer space. This paper proposes a virtual sensor model with partial vibration measurements using a convolutional neural network. The transmissibility function is employed as prior knowledge. A four-layer neural network with two convolutional layers, one fully connected layer, and an output layer is proposed as the predicting model. Numerical examples of two different structural dynamic systems demonstrate the performance of the proposed approach. The excellence of the novel technique is further indicated using a simply supported beam experiment comparing to a modal-model-based virtual sensor, which uses modal parameters, such as mode shapes, for estimating the responses of the faulty sensors. The results show that the presented data-driven response virtual sensor technique can predict structural response with high accuracy. PMID:29231868

Sensor Fusion and Smart Sensor in Sports and Biomedical Applications.

PubMed

Mendes, José Jair Alves; Vieira, Mário Elias Marinho; Pires, Marcelo Bissi; Stevan, Sergio Luiz

2016-09-23

The following work presents an overview of smart sensors and sensor fusion targeted at biomedical applications and sports areas. In this work, the integration of these areas is demonstrated, promoting a reflection about techniques and applications to collect, quantify and qualify some physical variables associated with the human body. These techniques are presented in various biomedical and sports applications, which cover areas related to diagnostics, rehabilitation, physical monitoring, and the development of performance in athletes, among others. Although some applications are described in only one of two fields of study (biomedicine and sports), it is very likely that the same application fits in both, with small peculiarities or adaptations. To illustrate the contemporaneity of applications, an analysis of specialized papers published in the last six years has been made. In this context, the main characteristic of this review is to present the largest quantity of relevant examples of sensor fusion and smart sensors focusing on their utilization and proposals, without deeply addressing one specific system or technique, to the detriment of the others.

Energy Harvesting Hybrid Acoustic-Optical Underwater Wireless Sensor Networks Localization.

PubMed

Saeed, Nasir; Celik, Abdulkadir; Al-Naffouri, Tareq Y; Alouini, Mohamed-Slim

2017-12-26

Underwater wireless technologies demand to transmit at higher data rate for ocean exploration. Currently, large coverage is achieved by acoustic sensor networks with low data rate, high cost, high latency, high power consumption, and negative impact on marine mammals. Meanwhile, optical communication for underwater networks has the advantage of the higher data rate albeit for limited communication distances. Moreover, energy consumption is another major problem for underwater sensor networks, due to limited battery power and difficulty in replacing or recharging the battery of a sensor node. The ultimate solution to this problem is to add energy harvesting capability to the acoustic-optical sensor nodes. Localization of underwater sensor networks is of utmost importance because the data collected from underwater sensor nodes is useful only if the location of the nodes is known. Therefore, a novel localization technique for energy harvesting hybrid acoustic-optical underwater wireless sensor networks (AO-UWSNs) is proposed. AO-UWSN employs optical communication for higher data rate at a short transmission distance and employs acoustic communication for low data rate and long transmission distance. A hybrid received signal strength (RSS) based localization technique is proposed to localize the nodes in AO-UWSNs. The proposed technique combines the noisy RSS based measurements from acoustic communication and optical communication and estimates the final locations of acoustic-optical sensor nodes. A weighted multiple observations paradigm is proposed for hybrid estimated distances to suppress the noisy observations and give more importance to the accurate observations. Furthermore, the closed form solution for Cramer-Rao lower bound (CRLB) is derived for localization accuracy of the proposed technique.

Energy Harvesting Hybrid Acoustic-Optical Underwater Wireless Sensor Networks Localization

PubMed Central

Saeed, Nasir; Celik, Abdulkadir; Al-Naffouri, Tareq Y.; Alouini, Mohamed-Slim

2017-01-01

Underwater wireless technologies demand to transmit at higher data rate for ocean exploration. Currently, large coverage is achieved by acoustic sensor networks with low data rate, high cost, high latency, high power consumption, and negative impact on marine mammals. Meanwhile, optical communication for underwater networks has the advantage of the higher data rate albeit for limited communication distances. Moreover, energy consumption is another major problem for underwater sensor networks, due to limited battery power and difficulty in replacing or recharging the battery of a sensor node. The ultimate solution to this problem is to add energy harvesting capability to the acoustic-optical sensor nodes. Localization of underwater sensor networks is of utmost importance because the data collected from underwater sensor nodes is useful only if the location of the nodes is known. Therefore, a novel localization technique for energy harvesting hybrid acoustic-optical underwater wireless sensor networks (AO-UWSNs) is proposed. AO-UWSN employs optical communication for higher data rate at a short transmission distance and employs acoustic communication for low data rate and long transmission distance. A hybrid received signal strength (RSS) based localization technique is proposed to localize the nodes in AO-UWSNs. The proposed technique combines the noisy RSS based measurements from acoustic communication and optical communication and estimates the final locations of acoustic-optical sensor nodes. A weighted multiple observations paradigm is proposed for hybrid estimated distances to suppress the noisy observations and give more importance to the accurate observations. Furthermore, the closed form solution for Cramer-Rao lower bound (CRLB) is derived for localization accuracy of the proposed technique. PMID:29278405

Postprandial kinetics of some biotic and abiotic characteristics of the gastric ecosystem of horses fed a pelleted concentrate meal.

PubMed

Varloud, M; Fonty, G; Roussel, A; Guyonvarch, A; Julliand, V

2007-10-01

Our knowledge of the microflora of the stomach of the horse is still limited, although some data indicate its important role in nutrition. The objective of this experiment was to investigate the microbial and biochemical profiles in the stomach of the horse and to quantify the disappearance of dietary starch. Total anaerobic bacteria, lactate-utilizing bacteria, lactobacilli, and streptococci were determined, and biochemical characteristics (pH, and DM, D- and L-lactate, D-glucose, NH3, and VFA concentrations) were measured in chyme collected from 4 horses by naso-gastric intubation aided by endoscopy, at 30 min before and 60, 120, and 210 min after the meal. The total anaerobic population exhibited a linear increase (5.54 to 6.98 log10 cfu/mL; P = 0.018) within the first postprandial hour and reached 8.32 log10 cfu/mL at 210 min after the meal. The concentrations of lactobacilli, streptococci, and lactate-utilizing bacteria in the stomach contents were 5.52, 4.82, and 6.95 log10 cfu/mL, respectively. Lactate concentration increased linearly from 0.25 mmol/L before the meal to 7.98 mmol/L at the last collection point (P = 0.013). This increase was mostly due to L-lactate accumulation. The VFA concentration increased linearly (P = 0.002) during the postprandial period from 1.96 to 8.17 mmol/L. Acetate represented, on average, 78 mol/100 mol of total VFA. The average concentration of NH3 in the stomach content was 2.48 mmol/L. Dietary starch disappearance did not respond during the post-prandial period and was not consistent with previous findings. These in vivo data provide complementary information on the postprandial microbial and biochemical kinetics in the stomachs of horses and confirm its abundant microbial colonization.

Homocysteine, folate, and vitamin B12 levels and vertebral fracture risk in postmenopausal women.

PubMed

El Maghraoui, Abdellah; Ghozlani, Imad; Mounach, Aziza; Rezqi, Asmaa; Oumghar, Khalid; Achemlal, Lahsen; Bezza, Ahmed; Ouzzif, Zhor

2012-01-01

The objective of this study was to examine the influence of homocysteine, vitamin B(12), and folate on the prevalence of asymptomatic osteoporotic vertebral fractures (VFs) using vertebral fracture assessment (VFA) in postmenopausal women. The study cohort consisted of 188 consecutive postmenopausal women (mean age, weight, and body mass index of 57.9 ± 8.5 [41-91]yr, 74.4 ± 13.5 [38-150]kg, and 30.4 ± 5.2 [17.1-50.7]kg/m(2), respectively). Lateral VFA images and scans of the lumbar spine and proximal femur were obtained using a Lunar Prodigy Vision densitometer (GE Healthcare Inc., Waukesha, WI). VFs were defined using a combination of Genant's semiquantitative approach and morphometry. Fifty-eight (30.9%) patients had densitometric osteoporosis. VFs were identified using VFA in 76 (40.4%) patients: 61 women had grade 1 VFs and 15 had grade 2 or 3 VFs. No statistical difference was shown between the 3 groups (absence of VFs, VFs grade 1, and VFs grade 2/3) concerning the biological parameters. Comparison of patients according to quartiles of homocysteine levels showed that women in the highest quartile were older and had a lower bone mineral density (BMD); however, the prevalence of VFs was not statistically different from that of women in the other quartile groups. Stepwise regression analysis showed that homocysteine was not independently associated with the presence of VFs, which was mainly related to the osteoporotic status. Although a weak association was observed between hyperhomocysteinemia and low BMD and a trend to higher prevalence of grade 2/3 VFs was observed, our study did not confirm that homocysteine, vitamin B(12), and folate status are important determinants of prevalent asymptomatic VFs in postmenopausal women. Copyright © 2012 The International Society for Clinical Densitometry. Published by Elsevier Inc. All rights reserved.

Effects of Aspergillus Oryzae Culture and 2-Hydroxy-4-(Methylthio)-Butanoic Acid on In vitro Rumen Fermentation and Microbial Populations between Different Roughage Sources.

PubMed

Sun, H; Wu, Y M; Wang, Y M; Liu, J X; Myung, K H

2014-09-01

An in vitro experiment was conducted to evaluate the effects of Aspergillus oryzae culture (AOC) and 2-hydroxy-4-(methylthio)-butanoic acid (HMB) on rumen fermentation and microbial populations between different roughage sources. Two roughage sources (Chinese wild rye [CWR] vs corn silage [CS]) were assigned in a 2×3 factorial arrangement with HMB (0 or 15 mg) and AOC (0, 3, or 6 mg). Gas production (GP), microbial protein (MCP) and total volatile fatty acid (VFA) were increased in response to addition of HMB and AOC (p<0.01) for the two roughages. The HMB and AOC showed inconsistent effects on ammonia-N with different substrates. For CWR, neither HMB nor AOC had significant effect on molar proportion of individual VFA. For CS, acetate was increased (p = 0.02) and butyrate was decreased (p<0.01) by adding HMB and AOC. Increase of propionate was only occurred with AOC (p<0.01). Populations of protozoa (p≤0.03) and fungi (p≤0.02) of CWR were differently influenced by HMB and AOC. Percentages of F. succinogenes, R. albus, and R. flavefaciens (p<0.01) increased when AOC was added to CWR. For CS, HMB decreased the protozoa population (p = 0.01) and increased the populations of F. succinogenes and R. albus (p≤0.03). Populations of fungi, F. succinogenes (p = 0.02) and R. flavefacien (p = 0.03) were increased by adding AOC. The HMB×AOC interactions were noted in MCP, fungi and R. flavefacien for CWR and GP, ammonia-N, MCP, total VFA, propionate, acetate/propionate (A/P) and R. albus for CS. It is inferred that addition of HMB and AOC could influence rumen fermentation of forages by increasing the number of rumen microbes.

Thermodynamic Driving Force of Hydrogen on Rumen Microbial Metabolism: A Theoretical Investigation

PubMed Central

van Lingen, Henk J.; Plugge, Caroline M.; Fadel, James G.; Kebreab, Ermias; Bannink, André; Dijkstra, Jan

2016-01-01

Hydrogen is a key product of rumen fermentation and has been suggested to thermodynamically control the production of the various volatile fatty acids (VFA). Previous studies, however, have not accounted for the fact that only thermodynamic near-equilibrium conditions control the magnitude of reaction rate. Furthermore, the role of NAD, which is affected by hydrogen partial pressure (PH2), has often not been considered. The aim of this study was to quantify the control of PH2 on reaction rates of specific fermentation pathways, methanogenesis and NADH oxidation in rumen microbes. The control of PH2 was quantified using the thermodynamic potential factor (FT), which is a dimensionless factor that corrects a predicted kinetic reaction rate for the thermodynamic control exerted. Unity FT was calculated for all glucose fermentation pathways considered, indicating no inhibition of PH2 on the production of a specific type of VFA (e.g., acetate, propionate and butyrate) in the rumen. For NADH oxidation without ferredoxin oxidation, increasing PH2 within the rumen physiological range decreased FT from unity to zero for different NAD+ to NADH ratios and pH of 6.2 and 7.0, which indicates thermodynamic control of PH2. For NADH oxidation with ferredoxin oxidation, increasing PH2 within the rumen physiological range decreased FT from unity at pH of 7.0 only. For the acetate to propionate conversion, FT increased from 0.65 to unity with increasing PH2, which indicates thermodynamic control. For propionate to acetate and butyrate to acetate conversions, FT decreased to zero below the rumen range of PH2, indicating full thermodynamic suppression. For methanogenesis by archaea without cytochromes, FT differed from unity only below the rumen range of PH2, indicating no thermodynamic control. This theoretical investigation shows that thermodynamic control of PH2 on individual VFA produced and associated yield of hydrogen and methane cannot be explained without considering NADH oxidation. PMID:27783615

Effects of rare earth element lanthanum on rumen methane and volatile fatty acid production and microbial flora in vitro.

PubMed

Zhang, T T; Zhao, G Y; Zheng, W S; Niu, W J; Wei, C; Lin, S X

2015-06-01

The objectives of the trial were to study the effects of rare earth element (REE) lanthanum (La) on the in vitro rumen methane (CH4 ) and volatile fatty acid (VFA) production and the microbial flora of feeds. Four feed mixtures with different levels of neutral detergent fibre (NDF), that is 20.0% (I), 31.0% (II), 41.9% (III) and 52.7% (IV), were formulated as substrates. Five levels of LaCl3 , that is 0, 0.4, 0.6, 0.8 and 1.0 mmol/kg dry matter (DM), were added to the feed mixtures, respectively, as experimental treatments in a two-factor 5 × 4 randomized design. The in vitro incubation lasted for 24 h. The results showed that supplementing LaCl3 increased the total gas (p < 0.001) production and tended to increase the total VFA production (p = 0.072) and decreased the CH4 production (p = 0.001) and the ratios of acetate/propionate (p = 0.019) and CH4 /total VFA (p < 0.001). Interactions between LaCl3 and NDF were significant in total gas production (p = 0.030) and tended to be significant in CH4 production (p = 0.071). Supplementing LaCl3 at the level of 0.8 mmol/g DM decreased the relative abundance of methanogens and protozoa in the total bacterial 16S rDNA analysed using the real-time PCR (p < 0.0001), increased F. succinogenes (p = 0.0003) and decreased R. flavefaciens (p < 0.0001) whereas did not affect R. albus and anaerobic fungi (p > 0.05). It was concluded that LaCl3 decreased the CH4 production without negatively affecting feed digestion through manipulating rumen microbial flora when feed mixtures with different levels of NDF were used as substrates. Journal of Animal Physiology and Animal Nutrition © 2014 Blackwell Verlag GmbH.

Effects of grain, fructose, and histidine on ruminal pH and fermentation products during an induced subacute acidosis protocol.

PubMed

Golder, H M; Celi, P; Rabiee, A R; Heuer, C; Bramley, E; Miller, D W; King, R; Lean, I J

2012-04-01

The effects of grain, fructose, and histidine on ruminal pH and fermentation products were studied in dairy cattle during an induced subacute acidosis protocol. Thirty Holstein heifers were randomly allocated to 5 treatment groups: (1) control (no grain); (2) grain [fed at a crushed triticale dry matter intake (DMI) of 1.2% of body weight (BW)]; (3) grain (0.8% of BW DMI)+fructose (0.4% of BW DMI); (4) grain (1.2% of BW DMI)+histidine (6 g/head); and (5) grain (0.8% of BW DMI)+fructose (0.4% of BW DMI)+histidine (6 g/head) in a partial factorial arrangement. Heifers were fed 1 kg of grain daily with ad libitum access to ryegrass silage and alfalfa hay for 10 d. Feed was withheld for 14 h before challenge day, on which heifers were fed 200 g of alfalfa hay and then the treatment diets immediately thereafter. Rumen samples were collected 5 min after diet ingestion, 60 min later, and at 3 subsequent 50-min intervals. Grain decreased ruminal pH and increased ammonia, total volatile fatty acid (VFA), acetate, butyrate, propionate, and valerate concentrations compared with controls. The addition of grain had no effect on ruminal D- and L-lactate concentrations. Fructose markedly decreased ruminal pH and markedly increased D- and L-lactate concentrations. Fructose increased total VFA and butyrate and decreased valerate concentrations. Although histidine did not have a marked effect on ruminal fermentation, increased concentrations of histamine were observed following feeding. This study demonstrates that the substitution of some grain for fructose can lower ruminal pH and increase VFA and lactate concentrations, warranting further investigation into the role of sugars on the risk of acidosis in dairy cattle. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

[Long-term efficacy of laser peripheral iridotomy in preventing progression in eyes with pigment dispersion syndrome].

PubMed

Qing, Guoping; Zhang, Shaodan; Wang, Huaizhou; Wang, Tao; Wang, Shuhua; Chen, Hong; Wang, Hua; Wang, Ningli

2014-07-01

To evaluate the long-term efficacy of laser peripheral iridotomy (LPI) in preventing deterioration in eyes with pigment dispersion syndrome (PDS). A cohort study. Nineteen patients with PDS were treated with LPI and followed up periodically in Beijing Tongren Eye Center from May 2006 to April 2007. One eye of each patient was chosen randomly for the study. Main investigating items included iris configuration, intraocular pressure (IOP), anterior chamber pigmentation, and visual field analysis. The average follow-up period was (6.5 ± 0.3) years. A paired sample t test was used to determine whether there is a significant difference between average values of pre- and post-LPI IOP and mean deviation of Humphrey visual field analysis in these PDS eyes. The average age of the 19 patients were (35.8 ± 7.1) years on admission. The initial IOP of the 19 eyes was (24.7 ± 2.2) mmHg (1 mmHg = 0.133 kPa) before LPI. The mean deviation (MD) of Humphrey visual field analysis (VFA) were (-1.82 ± 1.26) dB (-4.34--0.28 dB) . All 19 eyes had concave iris and heavy trabecular pigmentation. The iris became flat in all PDS eyes after the laser treatment. At the last follow-up visit, the average IOP was 14.8 ± 2.0 (12-20) mmHg, which was statistically lower than that of baseline (t = 11.49, P < 0.01) . Extent of trabecular pigmentation reduced obviously in 16 eyes. No deterioration or new visual field defect was detected in any of the PDS eyes. MD of the last VFA was -1.79 ± 1.21 (-4.39--0.21 dB) . There was no statistical difference between MD of the last VFA and baseline (t = -0.26, P = 0.798). The long-term follow-up results showed that LPI prevents progression effectively in eyes with PDS.

Denitrifying sulfur conversion-associated EBPR: The effect of pH on anaerobic metabolism and performance.

PubMed

Guo, Gang; Wu, Di; Hao, Tianwei; Mackey, Hamish Robert; Wei, Li; Chen, Guanghao

2017-10-15

The performance of the denitrifying sulfur conversion-associated enhanced biological phosphorus removal (DS-EBPR) process tends to be unstable and requires further study and development. This in turn requires extensive study of the anaerobic metabolism in terms of its stoichiometry and kinetics. This study evaluates the corresponding responses of DS-EBPR to pH, as it significantly influences both stoichiometry and biochemical kinetics. The impacts of five representative pH values ranging between 6.5 and 8.5 on the anaerobic metabolism were investigated, followed by identification of the optimal pH for performance optimization. A mature DS-EBPR sludge was used in the study, enriched with approximately 30% sulfate-reducing bacteria (SRB) and 33% sulfide-oxidizing bacteria (SOB). Through a series of batch tests, the optimal pH range was determined as 7.0-7.5. In this pH range, the anaerobic stoichiometry of phosphorus released/volatile fatty acid (VFA) uptake ratio, sulfate reduction, and internal polymer production (including poly-β-hydroxyalkanoates and polysulfide and/or elemental sulfur) all increased along with the anaerobic kinetics of the VFA uptake ratio. Consequently, phosphorus removal was maximized at this pH range (≥95% vs. 84-93% at other pH values), as was sulfur conversion (16 mg S/L vs. 10-13 mg S/L). This pH range therefore favors the activity and synergy of the key functional bacteria (i.e. SRB and SOB). Anaerobic maintenance tests showed these bacteria required 38-61% less energy for maintenance than that reported for GAOs regardless of pH changes, improving their ability to cope with anaerobic starvation. Adversely, both bacteria showed much lower VFA uptake rates than that of GAOs at all tested pH values (0.03-0.06 vs. 0.2-0.24 mol-C/C-mol biomass/h), possibly revealing the primary cause of frequent instability in the DS-EBPR process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Starch and fiber properties affect their kinetics of digestion and thereby digestive physiology in pigs.

PubMed

Zijlstra, R T; Jha, R; Woodward, A D; Fouhse, J; van Kempen, T A T G

2012-12-01

Traditionally in swine nutrition, analyses of starch and fiber have focused on assessing quantity; however, both have a wide range of functional properties making them underappreciated nutrients. Starch ranging from low to high amylose changes from rapidly digestible in the upper gut to poorly digestible but fermentable in the lower gut thereby changing from a source of glucose to VFA source. Likewise, fibers ranging from low to high viscosity affect digesta flow and from slowly to rapidly fermentable alter production of VFA serving as energy for the gut or whole body. Our hypothesis is that total extent, kinetics, and site of digestion or fermentation of starch and fiber are important for whole body nutrient use and intestinal health. To elucidate their effects, we developed in vitro, lab-based methodologies to describe kinetics of digestion and fermentation and linked these with in vivo models including i) ileum cannulation to collect digesta, ii) portal-vein catheterization to sequentially sample blood, iii) slaughter method to collect site-specific intestinal tissue and digesta, and iv) indirect calorimetry. Using these methods, kinetics of nutrient absorption was associated with pancreatic and intestinal hormones released into the portal vein, intestinal microbiota, and gene expression in intestinal tissue and microbiota. These studies confirmed that slowly digestible starch is partially degraded in the distal small and large intestine and fermented into VFA including butyrate (10-fold increase in net portal appearance), which reduces insulin responses by 60% and whole body energy use. Starch entering the distal intestine altered mRNA abundance of nutrient transporters and was bifidogenic. Extremely viscous purified fiber dampened glycemic responses and reduced digesta passage rate by 50% thereby increasing ileal digestion of dietary nutrients whereas increased fiber in feed grains reduced nutrient digestibility. Fermentable fiber increased butyrate and insulin production. These methods will therefore support elucidation of mechanisms that link starch and fiber properties to whole body nutrient use and intestinal health.

Anatomical calibration for wearable motion capture systems: Video calibrated anatomical system technique.

PubMed

Bisi, Maria Cristina; Stagni, Rita; Caroselli, Alessio; Cappello, Angelo

2015-08-01

Inertial sensors are becoming widely used for the assessment of human movement in both clinical and research applications, thanks to their usability out of the laboratory. This work aims to propose a method for calibrating anatomical landmark position in the wearable sensor reference frame with an ease to use, portable and low cost device. An off-the-shelf camera, a stick and a pattern, attached to the inertial sensor, compose the device. The proposed technique is referred to as video Calibrated Anatomical System Technique (vCAST). The absolute orientation of a synthetic femur was tracked both using the vCAST together with an inertial sensor and using stereo-photogrammetry as reference. Anatomical landmark calibration showed mean absolute error of 0.6±0.5 mm: these errors are smaller than those affecting the in-vivo identification of anatomical landmarks. The roll, pitch and yaw anatomical frame orientations showed root mean square errors close to the accuracy limit of the wearable sensor used (1°), highlighting the reliability of the proposed technique. In conclusion, the present paper proposes and preliminarily verifies the performance of a method (vCAST) for calibrating anatomical landmark position in the wearable sensor reference frame: the technique is low time consuming, highly portable, easy to implement and usable outside laboratory. Copyright © 2015 IPEM. Published by Elsevier Ltd. All rights reserved.

The effect of cellobiose on the health status of growing rabbits depends on the dietary level of soluble fiber.

PubMed

Ocasio-Vega, César; Delgado, Rebeca; Abad-Guamán, Rodrigo; Carabaño, Rosa; Carro, Maria Dolores; Menoyo, David; García, Javier

2018-05-04

The aim of this study was to examine whether the combination of dietary soluble fiber and cellobiose exerts a synergistic effect on growth performance, health status, fermentation traits, and immune response in rabbits. Six treatments in a 3 × 2 factorial arrangement were used: 3 cellobiose concentrations in drinking water (0.0, 7.5, and 15.0 g/L) × 2 dietary levels of soluble fiber (84.0 and 130 g/kg DM, for the low soluble fiber [LSF] and high soluble fiber [HSF] diets, respectively). A total of 318 young rabbits (53/treatment) were weaned at 34 d of age and had ad libitum access to feed and water. At 46 d of age, 9 rabbits/treatment were slaughtered and ileal and cecal digesta were collected to analyze VFA profile and the immune response in the cecal appendix mucosa. At 48 d of age, the cellobiose supplementation was withdrawn and the experimental diets were replaced by a standard commercial diet until 61 d of age. From 34 to 48 d of age, there was a linear increase of mortality with the level of cellobiose in the HSF group (0% vs. 17.1%; P = 0.017). In contrast, a quadratic effect of cellobiose level on mortality was observed in the LSF group, the rabbits offered 7.5-cellobiose showing the lowest mortality (5.7% vs. 21.4%; P = 0.030). Cellobiose level had a quadratic effect on ADFI, ADG, and G:F in this period (P ≤ 0.047), with the 7.5-cellobiose groups having the best growth performance. In contrast, only minor changes on these traits were observed from 48 d of age onwards. Cellobiose level influenced quadratically the ileal VFA concentrations (P = 0.014), showing the maximal value in the 7.5-cellobiose groups. In rabbits fed 7.5-cellobiose-LSF, a change of acetate to propionate, butyrate, and valerate was observed in the ileum. Increasing cellobiose levels reduced linearly cecal VFA concentrations in HSF fed rabbits, but no effect was detected in LSF groups (P = 0.046). The level of soluble fiber increased VFA concentrations in both the ileum (by 22%; P < 0.001), and the cecum (by 11%; P = 0.005). The relative gene expression of IL-6, IL-10, TNF-α, iNOS, MUC-1, and toll-like receptors (TLR-2 and TLR-4) in the cecal appendix increased linear and quadratically with increasing levels of cellobiose (P ≤ 0.063). In conclusion, in rabbits fed LSF diets, a dose of 7.5 g cellobiose/L drinking water would be recommended, whereas these levels of cellobiose supplementation should be avoided in rabbits fed HSF diets.

[Studies on anaerobic infection in oro-maxillary region--rapid diagnosis by gas-liquid chromatography and antibiotic susceptibilities of anaerobic bacteria].

PubMed

Tanaka, J I

1989-08-01

Subject material for this study was pus collected from patients with purulent inflammation in the oro-maxillary region. Direct gas-liquid chromatography (GLC) analysis was made, bacterial isolation and identification were carried out, and comparisons were made with results from GLC analysis and anaerobic isolates in a PYG medium. In addition, antibiotic susceptibilities of anaerobic bacteria were examined. Results 1. Anaerobic bacteria were isolated from 85 of 100 cases of obstructive abscesses. Of the 85, 49 were cases of mixed infection involving both anaerobic and aerobic bacteria; and 64 cases were involved with more than 2 species of anaerobic bacteria. Of the 184 strains of anaerobic isolates, 53 were Bacteroides sp. and 51 were Peptostreptococcus sp. The 2 groups accounted for more than half of the isolates. 2. Group A, in which no VFA was detected, accounted for 17 out of 100 cases. Group B, in which acetic acid was detected, accounted for 20 cases; and Group C, in which butyric acid was detected, accounted for 20 cases; and Group D, in which iso-valeric acid was detected, accounted for 8 cases. Direct GLC analysis revealed iso-caproic and caproic acids in the 35 cases constituting Group E. 3. Whereas the percentage of anaerobic bacteria was 64.7% in Group A and 60% in Group B, significantly higher percentages were noted in Group C (95%), Group D (100%) and Group E (100%). The following species were isolated as major member in the groups; Group A--Streptococcus intermedius, Group B--Peptostreptococcus micros, Group C--Fusobacterium nucleatum, Group D--Bacteroides gingivalis, and Group E--Peptostreptococcus anaerobius. 4. In all cases, the sum of VFA produced in the PYG medium by anaerobic isolates was classified into Group A' to E'. Ratios of agreement between VFA as revealed by direct GLC and VFA as revealed by PYG.GLC were as follows: Group A-A'; 47.1%, Group B-B' and C-C'; 45%, Group D-D'; 87.5%, and Group E-E'; 62.9%. 5. In Group B, no propionic acid was detected. The 2 cases in which acetic acid occurred in a concentration greater than 14 x 10(-4) meq/ml belonged to Group B'. In Group C, no isobutyric acid was detected; and the 5 cases in which butyric acid was detected in a concentration of more than 7 x 10(-4) meq/ml belonged to Group C'. Varelic acid was not detected in Group D; and 7 out of the 8 cases in which iso-valeric acid, irrespective of concentration, was detected belonged to Group D'.(ABSTRACT TRUNCATED AT 400 WORDS)

Effect of acarbose on acute acidosis.

PubMed

McLaughlin, C L; Thompson, A; Greenwood, K; Sherington, J; Bruce, C

2009-06-01

A challenge model was used to evaluate a new approach to controlling acute acidosis. Acute acidosis reduces performance in both dairy and beef cattle and most often occurs as a consequence of ingestion of large amounts of readily fermentable starch, resulting in increased production of volatile fatty acids (VFA) and lactic acid and a reduction in ruminal pH. Acarbose is an alpha-amylase and glucosidase inhibitor that slows the rate of degradation of starch to glucose, thereby reducing the rate of VFA production and maintaining rumen pH at a more stable level. It is commercially available (Glucobay, Bayer, Wuppertal, Germany) and indicated for the control of blood glucose in diabetic patients. The ability of acarbose to reduce the incidence of acidosis and the comparative efficacies of acarbose, sodium bicarbonate, and monensin were tested in 3 acute acidosis challenge experiments in cattle. Rumen-cannulated Holstein steers were challenged with a mixture of 48.4% cornstarch, 48.4% ground corn, 2.1% sodium caseinate, and 1.1% urea with or without test substance. The challenge was administered at a rate of 12.5 g/kg of body weight (BW) as a slurry through the cannula directly into the rumen. Ruminal pH was monitored at 10-min intervals throughout the study. Animals were removed from study and rumen contents replaced if they exhibited acute acidosis as defined as pH <4.5. If acidosis was not observed within 24 h, animals were subjected to a second challenge. Ruminal fluid samples were taken for measurement of VFA and lactate concentrations at various intervals after the challenge. In experiment 1, the carbohydrate challenge induced acidosis in 4 of 4 control animals and 0 of 4 animals treated with 2.14 or 21.4 mg of acarbose/kg of BW in the challenge based on the criterion of pH <4.5. In experiment 2, the carbohydrate challenge induced acidosis in 4 of 7 control animals and 1 of 7 animals when 1.07 mg of acarbose/kg of BW was included in the challenge. In experiment 3, acidosis was induced in 7 of 7 animals in the control, 1% sodium bicarbonate, and 12 mg of monensin/kg of dry matter intake groups and in 3 of 8 steers administered 1.07 mg of acarbose/kg of BW in the challenge. Increases in lactate concentrations and decreases in total VFA associated with acute acidosis were mitigated by acarbose. Thus, acarbose, an amylase and glucosidase inhibitor, prevented or reduced the incidence of acidosis in an acute challenge model in steers and was more effective than monensin or sodium bicarbonate.

Single Photon Counting Performance and Noise Analysis of CMOS SPAD-Based Image Sensors.

PubMed

Dutton, Neale A W; Gyongy, Istvan; Parmesan, Luca; Henderson, Robert K

2016-07-20

SPAD-based solid state CMOS image sensors utilising analogue integrators have attained deep sub-electron read noise (DSERN) permitting single photon counting (SPC) imaging. A new method is proposed to determine the read noise in DSERN image sensors by evaluating the peak separation and width (PSW) of single photon peaks in a photon counting histogram (PCH). The technique is used to identify and analyse cumulative noise in analogue integrating SPC SPAD-based pixels. The DSERN of our SPAD image sensor is exploited to confirm recent multi-photon threshold quanta image sensor (QIS) theory. Finally, various single and multiple photon spatio-temporal oversampling techniques are reviewed.

Dual-angle technique for simultaneous measurement of refractive index and temperature based on a surface plasmon resonance sensor.

PubMed

Luo, Wei; Chen, Sheng; Chen, Lei; Li, Hualong; Miao, Pengcheng; Gao, Huiyi; Hu, Zelin; Li, Miao

2017-05-29

We describe a theoretical model to analyze temperature effects on the Kretschmann surface plasmon resonance (SPR) sensor, and describe a new double-incident angle technique to simultaneously measure changes in refractive index (RI) and temperature. The method uses the observation that output signals obtained from two different incident angles each have a linear dependence on RI and temperature, and are independent. A proof-of-concept experiment using different NaCl concentration solutions as analytes demonstrates the ability of the technique. The optical design is as simple and robust as conventional SPR detection, but provides a way to discriminate between RI-induced and temperature-induced SPR changes. This technique facilitates a way for traditional SPR sensors to detect RI in different temperature environments, and may lead to better design and fabrication of SPR sensors against temperature variation.

Energy neutral protocol based on hierarchical routing techniques for energy harvesting wireless sensor network

NASA Astrophysics Data System (ADS)

Muhammad, Umar B.; Ezugwu, Absalom E.; Ofem, Paulinus O.; Rajamäki, Jyri; Aderemi, Adewumi O.

2017-06-01

Recently, researchers in the field of wireless sensor networks have resorted to energy harvesting techniques that allows energy to be harvested from the ambient environment to power sensor nodes. Using such Energy harvesting techniques together with proper routing protocols, an Energy Neutral state can be achieved so that sensor nodes can run perpetually. In this paper, we propose an Energy Neutral LEACH routing protocol which is an extension to the traditional LEACH protocol. The goal of the proposed protocol is to use Gateway node in each cluster so as to reduce the data transmission ranges of cluster head nodes. Simulation results show that the proposed routing protocol achieves a higher throughput and ensure the energy neutral status of the entire network.

New sensors and techniques for the structural health monitoring of propulsion systems.

PubMed

Woike, Mark; Abdul-Aziz, Ali; Oza, Nikunj; Matthews, Bryan

2013-01-01

The ability to monitor the structural health of the rotating components, especially in the hot sections of turbine engines, is of major interest to aero community in improving engine safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, are able to operate in a high temperature environment, and can detect minute changes and hidden flaws before catastrophic events occur. The National Aeronautics and Space Administration (NASA), through the Aviation Safety Program (AVSP), has taken a lead role in the development of new sensor technologies and techniques for the in situ structural health monitoring of gas turbine engines. This paper presents a summary of key results and findings obtained from three different structural health monitoring approaches that have been investigated. This includes evaluating the performance of a novel microwave blade tip clearance sensor; a vibration based crack detection technique using an externally mounted capacitive blade tip clearance sensor; and lastly the results of using data driven anomaly detection algorithms for detecting cracks in a rotating disk.

New Sensors and Techniques for the Structural Health Monitoring of Propulsion Systems

PubMed Central

2013-01-01

The ability to monitor the structural health of the rotating components, especially in the hot sections of turbine engines, is of major interest to aero community in improving engine safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, are able to operate in a high temperature environment, and can detect minute changes and hidden flaws before catastrophic events occur. The National Aeronautics and Space Administration (NASA), through the Aviation Safety Program (AVSP), has taken a lead role in the development of new sensor technologies and techniques for the in situ structural health monitoring of gas turbine engines. This paper presents a summary of key results and findings obtained from three different structural health monitoring approaches that have been investigated. This includes evaluating the performance of a novel microwave blade tip clearance sensor; a vibration based crack detection technique using an externally mounted capacitive blade tip clearance sensor; and lastly the results of using data driven anomaly detection algorithms for detecting cracks in a rotating disk. PMID:23935425

Cross-sensor iris recognition through kernel learning.

PubMed

Pillai, Jaishanker K; Puertas, Maria; Chellappa, Rama

2014-01-01

Due to the increasing popularity of iris biometrics, new sensors are being developed for acquiring iris images and existing ones are being continuously upgraded. Re-enrolling users every time a new sensor is deployed is expensive and time-consuming, especially in applications with a large number of enrolled users. However, recent studies show that cross-sensor matching, where the test samples are verified using data enrolled with a different sensor, often lead to reduced performance. In this paper, we propose a machine learning technique to mitigate the cross-sensor performance degradation by adapting the iris samples from one sensor to another. We first present a novel optimization framework for learning transformations on iris biometrics. We then utilize this framework for sensor adaptation, by reducing the distance between samples of the same class, and increasing it between samples of different classes, irrespective of the sensors acquiring them. Extensive evaluations on iris data from multiple sensors demonstrate that the proposed method leads to improvement in cross-sensor recognition accuracy. Furthermore, since the proposed technique requires minimal changes to the iris recognition pipeline, it can easily be incorporated into existing iris recognition systems.

Short, multi-needle FDR sensor suitable for measuring soil water content

USDA-ARS?s Scientific Manuscript database

Time domain reflectometry (TDR) is a well-established electromagnetic technique used to measure soil water content. TDR sensors have been combined with heat pulse sensors to produce thermo-TDR sensors. Thermo-TDR sensors are restricted to having relatively short needles in order to accurately measur...

Optimizing remote sensing and GIS tools for mapping and managing the distribution of an invasive mangrove (Rhizophora mangle) on South Molokai, Hawaii

USGS Publications Warehouse

D'Iorio, M.; Jupiter, S.D.; Cochran, S.A.; Potts, D.C.

2007-01-01

In 1902, the Florida red mangrove, Rhizophora mangle L., was introduced to the island of Molokai, Hawaii, and has since colonized nearly 25% of the south coast shoreline. By classifying three kinds of remote sensing imagery, we compared abilities to detect invasive mangrove distributions and to discriminate mangroves from surrounding terrestrial vegetation. Using three analytical techniques, we compared mangrove mapping accuracy for various sensor-technique combinations. ANOVA of accuracy assessments demonstrated significant differences among techniques, but no significant differences among the three sensors. We summarize advantages and disadvantages of each sensor and technique for mapping mangrove distributions in tropical coastal environments.

Reducing multi-sensor data to a single time course that reveals experimental effects

PubMed Central

2013-01-01

Background Multi-sensor technologies such as EEG, MEG, and ECoG result in high-dimensional data sets. Given the high temporal resolution of such techniques, scientific questions very often focus on the time-course of an experimental effect. In many studies, researchers focus on a single sensor or the average over a subset of sensors covering a “region of interest” (ROI). However, single-sensor or ROI analyses ignore the fact that the spatial focus of activity is constantly changing, and fail to make full use of the information distributed over the sensor array. Methods We describe a technique that exploits the optimality and simplicity of matched spatial filters in order to reduce experimental effects in multivariate time series data to a single time course. Each (multi-sensor) time sample of each trial is replaced with its projection onto a spatial filter that is matched to an observed experimental effect, estimated from the remaining trials (Effect-Matched Spatial filtering, or EMS filtering). The resulting set of time courses (one per trial) can be used to reveal the temporal evolution of an experimental effect, which distinguishes this approach from techniques that reveal the temporal evolution of an anatomical source or region of interest. Results We illustrate the technique with data from a dual-task experiment and use it to track the temporal evolution of brain activity during the psychological refractory period. We demonstrate its effectiveness in separating the means of two experimental conditions, and in significantly improving the signal-to-noise ratio at the single-trial level. It is fast to compute and results in readily-interpretable time courses and topographies. The technique can be applied to any data-analysis question that can be posed independently at each sensor, and we provide one example, using linear regression, that highlights the versatility of the technique. Conclusion The approach described here combines established techniques in a way that strikes a balance between power, simplicity, speed of processing, and interpretability. We have used it to provide a direct view of parallel and serial processes in the human brain that previously could only be measured indirectly. An implementation of the technique in MatLab is freely available via the internet. PMID:24125590

Effect of sprouted barley grain supplementation of an herbage or haylage diet on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

A 4-unit dual-flow continuous culture fermentor system was used to assess the effect of supplementing 7-d sprouted barley (SB) or barley grain (BG), with a pasture (orchardgrass) or haylage diet, on nutrient digestibility, VFA production, bacterial protein synthesis, and methane production. Treatmen...

Changes in rumen bacterial communities and rumen chemistry in primiparous Holstein cows during the periparturient period

USDA-ARS?s Scientific Manuscript database

The objectives of this study were to study the changes in: 1) rumen bacterial community composition (BCC) and fermentation as influenced by feeding regimen and period; and 2) pH and VFA profiles among selected cows with minimum (stable) and maximum variation (unstable) between pre- and post-parturie...

Role of rumen butyrate in regulation of nitrogen utilization and urea nitrogen kinetics in growing sheep

USDA-ARS?s Scientific Manuscript database

Butyrate, a major rumen VFA, has been indirectly linked to enhancement of urea recycling based on increased expression of urea transporter (UT-B) in the rumen epithelia of steers fed a rumen butyrate-enhancing diet. Two studies were conducted to quantify the effect of elevated rumen butyrate concent...

Effect of feeding warm-season annuals with orchardgrass on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

A 4-unit, dual-flow continuous culture fermentor system was used to assess nutrient digestibility, volatile fatty acids (VFA) production, bacterial protein synthesis and CH4 output of warm-season summer annual grasses. Treatments were randomly assigned to fermentors in a 4 × 4 Latin square design us...

A Radiosonde Using a Humidity Sensor Array with a Platinum Resistance Heater and Multi-Sensor Data Fusion

PubMed Central

Shi, Yunbo; Luo, Yi; Zhao, Wenjie; Shang, Chunxue; Wang, Yadong; Chen, Yinsheng

2013-01-01

This paper describes the design and implementation of a radiosonde which can measure the meteorological temperature, humidity, pressure, and other atmospheric data. The system is composed of a CPU, microwave module, temperature sensor, pressure sensor and humidity sensor array. In order to effectively solve the humidity sensor condensation problem due to the low temperatures in the high altitude environment, a capacitive humidity sensor including four humidity sensors to collect meteorological humidity and a platinum resistance heater was developed using micro-electro-mechanical-system (MEMS) technology. A platinum resistance wire with 99.999% purity and 0.023 mm in diameter was used to obtain the meteorological temperature. A multi-sensor data fusion technique was applied to process the atmospheric data. Static and dynamic experimental results show that the designed humidity sensor with platinum resistance heater can effectively tackle the sensor condensation problem, shorten response times and enhance sensitivity. The humidity sensor array can improve measurement accuracy and obtain a reliable initial meteorological humidity data, while the multi-sensor data fusion technique eliminates the uncertainty in the measurement. The radiosonde can accurately reflect the meteorological changes. PMID:23857263

A radiosonde using a humidity sensor array with a platinum resistance heater and multi-sensor data fusion.

PubMed

Shi, Yunbo; Luo, Yi; Zhao, Wenjie; Shang, Chunxue; Wang, Yadong; Chen, Yinsheng

2013-07-12

This paper describes the design and implementation of a radiosonde which can measure the meteorological temperature, humidity, pressure, and other atmospheric data. The system is composed of a CPU, microwave module, temperature sensor, pressure sensor and humidity sensor array. In order to effectively solve the humidity sensor condensation problem due to the low temperatures in the high altitude environment, a capacitive humidity sensor including four humidity sensors to collect meteorological humidity and a platinum resistance heater was developed using micro-electro-mechanical-system (MEMS) technology. A platinum resistance wire with 99.999% purity and 0.023 mm in diameter was used to obtain the meteorological temperature. A multi-sensor data fusion technique was applied to process the atmospheric data. Static and dynamic experimental results show that the designed humidity sensor with platinum resistance heater can effectively tackle the sensor condensation problem, shorten response times and enhance sensitivity. The humidity sensor array can improve measurement accuracy and obtain a reliable initial meteorological humidity data, while the multi-sensor data fusion technique eliminates the uncertainty in the measurement. The radiosonde can accurately reflect the meteorological changes.

Validation of polyvinylidene fluoride nasal sensor to assess nasal obstruction in comparison with subjective technique.

PubMed

Roopa Manjunatha, G; Mahapatra, D Roy; Prakash, Surya; Rajanna, K

2015-01-01

The aim of this study is to validate the applicability of the PolyVinyliDene Fluoride (PVDF) nasal sensor to assess the nasal airflow, in healthy subjects and patients with nasal obstruction and to correlate the results with the score of Visual Analogue Scale (VAS). PVDF nasal sensor and VAS measurements were carried out in 50 subjects (25-healthy subjects and 25 patients). The VAS score of nasal obstruction and peak-to-peak amplitude (Vp-p) of nasal cycle measured by PVDF nasal sensors were analyzed for right nostril (RN) and left nostril (LN) in both the groups. Spearman's rho correlation was calculated. The relationship between PVDF nasal sensor measurements and severity of nasal obstruction (VAS score) were assessed by ANOVA. In healthy group, the measurement of nasal airflow by PVDF nasal sensor for RN and LN were found to be 51.14±5.87% and 48.85±5.87%, respectively. In patient group, PVDF nasal sensor indicated lesser nasal airflow in the blocked nostrils (RN: 23.33±10.54% and LN: 32.24±11.54%). Moderate correlation was observed in healthy group (r=-0.710, p<0.001 for RN and r=-0.651, p<0.001 for LN), and moderate to strong correlation in patient group (r=-0.751, p<0.01 for RN and r=-0.885, p<0.0001 for LN). PVDF nasal sensor method is a newly developed technique for measuring the nasal airflow. Moderate to strong correlation was observed between PVDF nasal sensor data and VAS scores for nasal obstruction. In our present study, PVDF nasal sensor technique successfully differentiated between healthy subjects and patients with nasal obstruction. Additionally, it can also assess severity of nasal obstruction in comparison with VAS. Thus, we propose that the PVDF nasal sensor technique could be used as a new diagnostic method to evaluate nasal obstruction in routine clinical practice. Copyright © 2015 Elsevier Inc. All rights reserved.

Calibrating a novel multi-sensor physical activity measurement system.

PubMed

John, D; Liu, S; Sasaki, J E; Howe, C A; Staudenmayer, J; Gao, R X; Freedson, P S

2011-09-01

Advancing the field of physical activity (PA) monitoring requires the development of innovative multi-sensor measurement systems that are feasible in the free-living environment. The use of novel analytical techniques to combine and process these multiple sensor signals is equally important. This paper describes a novel multi-sensor 'integrated PA measurement system' (IMS), the lab-based methodology used to calibrate the IMS, techniques used to predict multiple variables from the sensor signals, and proposes design changes to improve the feasibility of deploying the IMS in the free-living environment. The IMS consists of hip and wrist acceleration sensors, two piezoelectric respiration sensors on the torso, and an ultraviolet radiation sensor to obtain contextual information (indoors versus outdoors) of PA. During lab-based calibration of the IMS, data were collected on participants performing a PA routine consisting of seven different ambulatory and free-living activities while wearing a portable metabolic unit (criterion measure) and the IMS. Data analyses on the first 50 adult participants are presented. These analyses were used to determine if the IMS can be used to predict the variables of interest. Finally, physical modifications for the IMS that could enhance the feasibility of free-living use are proposed and refinement of the prediction techniques is discussed.

Interband cascade laser based mid-infrared methane sensor system using a novel electrical-domain self-adaptive direct laser absorption spectroscopy (SA-DLAS).

PubMed

Song, Fang; Zheng, Chuantao; Yan, Wanhong; Ye, Weilin; Wang, Yiding; Tittel, Frank K

2017-12-11

To suppress sensor noise with unknown statistical properties, a novel self-adaptive direct laser absorption spectroscopy (SA-DLAS) technique was proposed by incorporating a recursive, least square (RLS) self-adaptive denoising (SAD) algorithm and a 3291 nm interband cascade laser (ICL) for methane (CH 4 ) detection. Background noise was suppressed by introducing an electrical-domain noise-channel and an expectation-known-based RLS SAD algorithm. Numerical simulations and measurements were carried out to validate the function of the SA-DLAS technique by imposing low-frequency, high-frequency, White-Gaussian and hybrid noise on the ICL scan signal. Sensor calibration, stability test and dynamic response measurement were performed for the SA-DLAS sensor using standard or diluted CH 4 samples. With the intrinsic sensor noise considered only, an Allan deviation of ~43.9 ppbv with a ~6 s averaging time was obtained and it was further decreased to 6.3 ppbv with a ~240 s averaging time, through the use of self-adaptive filtering (SAF). The reported SA-DLAS technique shows enhanced sensitivity compared to a DLAS sensor using a traditional sensing architecture and filtering method. Indoor and outdoor atmospheric CH 4 measurements were conducted to validate the normal operation of the reported SA-DLAS technique.

A hybrid artificial neural network as a software sensor for optimal control of a wastewater treatment process.

PubMed

Choi, D J; Park, H

2001-11-01

For control and automation of biological treatment processes, lack of reliable on-line sensors to measure water quality parameters is one of the most important problems to overcome. Many parameters cannot be measured directly with on-line sensors. The accuracy of existing hardware sensors is also not sufficient and maintenance problems such as electrode fouling often cause trouble. This paper deals with the development of software sensor techniques that estimate the target water quality parameter from other parameters using the correlation between water quality parameters. We focus our attention on the preprocessing of noisy data and the selection of the best model feasible to the situation. Problems of existing approaches are also discussed. We propose a hybrid neural network as a software sensor inferring wastewater quality parameter. Multivariate regression, artificial neural networks (ANN), and a hybrid technique that combines principal component analysis as a preprocessing stage are applied to data from industrial wastewater processes. The hybrid ANN technique shows an enhancement of prediction capability and reduces the overfitting problem of neural networks. The result shows that the hybrid ANN technique can be used to extract information from noisy data and to describe the nonlinearity of complex wastewater treatment processes.

An analysis of the uncertainty and bias in DCE-MRI measurements using the spoiled gradient-recalled echo pulse sequence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Subashi, Ergys; Choudhury, Kingshuk R.; Johnson, G. Allan, E-mail: gjohnson@duke.edu

2014-03-15

Purpose: The pharmacokinetic parameters derived from dynamic contrast-enhanced (DCE) MRI have been used in more than 100 phase I trials and investigator led studies. A comparison of the absolute values of these quantities requires an estimation of their respective probability distribution function (PDF). The statistical variation of the DCE-MRI measurement is analyzed by considering the fundamental sources of error in the MR signal intensity acquired with the spoiled gradient-echo (SPGR) pulse sequence. Methods: The variance in the SPGR signal intensity arises from quadrature detection and excitation flip angle inconsistency. The noise power was measured in 11 phantoms of contrast agentmore » concentration in the range [0–1] mM (in steps of 0.1 mM) and in onein vivo acquisition of a tumor-bearing mouse. The distribution of the flip angle was determined in a uniform 10 mM CuSO{sub 4} phantom using the spin echo double angle method. The PDF of a wide range of T1 values measured with the varying flip angle (VFA) technique was estimated through numerical simulations of the SPGR equation. The resultant uncertainty in contrast agent concentration was incorporated in the most common model of tracer exchange kinetics and the PDF of the derived pharmacokinetic parameters was studied numerically. Results: The VFA method is an unbiased technique for measuringT1 only in the absence of bias in excitation flip angle. The time-dependent concentration of the contrast agent measured in vivo is within the theoretically predicted uncertainty. The uncertainty in measuring K{sup trans} with SPGR pulse sequences is of the same order, but always higher than, the uncertainty in measuring the pre-injection longitudinal relaxation time (T1{sub 0}). The lowest achievable bias/uncertainty in estimating this parameter is approximately 20%–70% higher than the bias/uncertainty in the measurement of the pre-injection T1 map. The fractional volume parameters derived from the extended Tofts model were found to be extremely sensitive to the variance in signal intensity. The SNR of the pre-injection T1 map indicates the limiting precision with which K{sup trans} can be calculated. Conclusions: Current small-animal imaging systems and pulse sequences robust to motion artifacts have the capacity for reproducible quantitative acquisitions with DCE-MRI. In these circumstances, it is feasible to achieve a level of precision limited only by physiologic variability.« less

Fabrication of strain gauge based sensors for tactile skins

NASA Astrophysics Data System (ADS)

Baptist, Joshua R.; Zhang, Ruoshi; Wei, Danming; Saadatzi, Mohammad Nasser; Popa, Dan O.

2017-05-01

Fabricating cost effective, reliable and functional sensors for electronic skins has been a challenging undertaking for the last several decades. Application of such skins include haptic interfaces, robotic manipulation, and physical human-robot interaction. Much of our recent work has focused on producing compliant sensors that can be easily formed around objects to sense normal, tension, or shear forces. Our past designs have involved the use of flexible sensors and interconnects fabricated on Kapton substrates, and piezoresistive inks that are 3D printed using Electro Hydro Dynamic (EHD) jetting onto interdigitated electrode (IDE) structures. However, EHD print heads require a specialized nozzle and the application of a high-voltage electric field; for which, tuning process parameters can be difficult based on the choice of inks and substrates. Therefore, in this paper we explore sensor fabrication techniques using a novel wet lift-off photolithographic technique for patterning the base polymer piezoresistive material, specifically Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) or PEDOT:PSS. Fabricated sensors are electrically and thermally characterized, and temperaturecompensated designs are proposed and validated. Packaging techniques for sensors in polymer encapsulants are proposed and demonstrated to produce a tactile interface device for a robot.

Velocity Profile measurements in two-phase flow using multi-wave sensors

NASA Astrophysics Data System (ADS)

Biddinika, M. K.; Ito, D.; Takahashi, H.; Kikura, H.; Aritomi, M.

2009-02-01

Two-phase flow has been recognized as one of the most important phenomena in fluid dynamics. In addition, gas-liquid two-phase flow appears in various industrial fields such as chemical industries and power generations. In order to clarify the flow structure, some flow parameters have been measured by using many effective measurement techniques. The velocity profile as one of the important flow parameter, has been measured by using ultrasonic velocity profile (UVP) technique. This technique can measure velocity distributions along a measuring line, which is a beam formed by pulse ultrasounds. Furthermore, a multi-wave sensor can measure the velocity profiles of both gas and liquid phase using UVP method. In this study, two types of multi-wave sensors are used. A sensor has cylindrical shape, and another one has square shape. The piezoelectric elements of each sensor have basic frequencies of 8 MHz for liquid phase and 2 MHz for gas phase, separately. The velocity profiles of air-water bubbly flow in a vertical rectangular channel were measured by using these multi-wave sensors, and the validation of the measuring accuracy was performed by the comparison between the velocity profiles measured by two multi-wave sensors.

On Applicability of Network Coding Technique for 6LoWPAN-based Sensor Networks.

PubMed

Amanowicz, Marek; Krygier, Jaroslaw

2018-05-26

In this paper, the applicability of the network coding technique in 6LoWPAN-based sensor multihop networks is examined. The 6LoWPAN is one of the standards proposed for the Internet of Things architecture. Thus, we can expect the significant growth of traffic in such networks, which can lead to overload and decrease in the sensor network lifetime. The authors propose the inter-session network coding mechanism that can be implemented in resource-limited sensor motes. The solution reduces the overall traffic in the network, and in consequence, the energy consumption is decreased. Used procedures take into account deep header compressions of the native 6LoWPAN packets and the hop-by-hop changes of the header structure. Applied simplifications reduce signaling traffic that is typically occurring in network coding deployments, keeping the solution usefulness for the wireless sensor networks with limited resources. The authors validate the proposed procedures in terms of end-to-end packet delay, packet loss ratio, traffic in the air, total energy consumption, and network lifetime. The solution has been tested in a real wireless sensor network. The results confirm the efficiency of the proposed technique, mostly in delay-tolerant sensor networks.

Flight testing of a luminescent surface pressure sensor

NASA Technical Reports Server (NTRS)

Mclachlan, B. G.; Bell, J. H.; Espina, J.; Gallery, J.; Gouterman, M.; Demandante, C. G. N.; Bjarke, L.

1992-01-01

NASA ARC has conducted flight tests of a new type of aerodynamic pressure sensor based on a luminescent surface coating. Flights were conducted at the NASA ARC-Dryden Flight Research Facility. The luminescent pressure sensor is based on a surface coating which, when illuminated with ultraviolet light, emits visible light with an intensity dependent on the local air pressure on the surface. This technique makes it possible to obtain pressure data over the entire surface of an aircraft, as opposed to conventional instrumentation, which can only make measurements at pre-selected points. The objective of the flight tests was to evaluate the effectiveness and practicality of a luminescent pressure sensor in the actual flight environment. A luminescent pressure sensor was installed on a fin, the Flight Test Fixture (FTF), that is attached to the underside of an F-104 aircraft. The response of one particular surface coating was evaluated at low supersonic Mach numbers (M = 1.0-1.6) in order to provide an initial estimate of the sensor's capabilities. This memo describes the test approach, the techniques used, and the pressure sensor's behavior under flight conditions. A direct comparison between data provided by the luminescent pressure sensor and that produced by conventional pressure instrumentation shows that the luminescent sensor can provide quantitative data under flight conditions. However, the test results also show that the sensor has a number of limitations which must be addressed if this technique is to prove useful in the flight environment.

Hierarchical classification in high dimensional numerous class cases

NASA Technical Reports Server (NTRS)

Kim, Byungyong; Landgrebe, D. A.

1990-01-01

As progress in new sensor technology continues, increasingly high resolution imaging sensors are being developed. These sensors give more detailed and complex data for each picture element and greatly increase the dimensionality of data over past systems. Three methods for designing a decision tree classifier are discussed: a top down approach, a bottom up approach, and a hybrid approach. Three feature extraction techniques are implemented. Canonical and extended canonical techniques are mainly dependent upon the mean difference between two classes. An autocorrelation technique is dependent upon the correlation differences. The mathematical relationship between sample size, dimensionality, and risk value is derived.

Thin Film Physical Sensor Instrumentation Research and Development at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Wrbanek, John D.; Fralick, Gustave C.

2006-01-01

A range of thin film sensor technology has been demonstrated enabling measurement of multiple parameters either individually or in sensor arrays including temperature, strain, heat flux, and flow. Multiple techniques exist for refractory thin film fabrication, fabrication and integration on complex surfaces and multilayered thin film insulation. Leveraging expertise in thin films and high temperature materials, investigations for the applications of thin film ceramic sensors has begun. The current challenges of instrumentation technology are to further develop systems packaging and component testing of specialized sensors, further develop instrumentation techniques on complex surfaces, improve sensor durability, and to address needs for extreme temperature applications. The technology research and development ongoing at NASA Glenn for applications to future launch vehicles, space vehicles, and ground systems is outlined.

Nanostructured Metal Oxide Gas Sensors, a Survey of Applications Carried out at SENSOR Lab, Brescia (Italy) in the Security and Food Quality Fields

PubMed Central

Ponzoni, Andrea; Comini, Elisabetta; Concina, Isabella; Ferroni, Matteo; Falasconi, Matteo; Gobbi, Emanuela; Sberveglieri, Veronica; Sberveglieri, Giorgio

2012-01-01

In this work we report on metal oxide (MOX) based gas sensors, presenting the work done at the SENSOR laboratory of the CNR-IDASC and University of Brescia, Italy since the 80s up to the latest results achieved in recent times. In particular we report the strategies followed at SENSOR during these 30 years to increase the performance of MOX sensors through the development of different preparation techniques, from Rheotaxial Growth Thermal Oxidation (RGTO) to nanowire technology to address sensitivity and stability, and the development of electronic nose systems and pattern recognition techniques to address selectivity. We will show the obtained achievement in the context of selected applications such as safety and security and food quality control. PMID:23235445

A screen-printed flexible flow sensor

NASA Astrophysics Data System (ADS)

Moschos, A.; Syrovy, T.; Syrova, L.; Kaltsas, G.

2017-04-01

A thermal flow sensor was printed on a flexible plastic substrate using exclusively screen-printing techniques. The presented device was implemented with custom made screen-printed thermistors, which allows simple, cost-efficient production on a variety of flexible substrates while maintaining the typical advantages of thermal flow sensors. Evaluation was performed for both static (zero flow) and dynamic conditions using a combination of electrical measurements and IR imaging techniques in order to determine important characteristics, such as temperature response, output repeatability, etc. The flow sensor was characterized utilizing the hot-wire and calorimetric principles of operation, while the preliminary results appear to be very promising, since the sensor was successfully evaluated and displayed adequate sensitivity in a relatively wide flow range.

Sensor Data Qualification System (SDQS) Implementation Study

NASA Technical Reports Server (NTRS)

Wong, Edmond; Melcher, Kevin; Fulton, Christopher; Maul, William

2009-01-01

The Sensor Data Qualification System (SDQS) is being developed to provide a sensor fault detection capability for NASA s next-generation launch vehicles. In addition to traditional data qualification techniques (such as limit checks, rate-of-change checks and hardware redundancy checks), SDQS can provide augmented capability through additional techniques that exploit analytical redundancy relationships to enable faster and more sensitive sensor fault detection. This paper documents the results of a study that was conducted to determine the best approach for implementing a SDQS network configuration that spans multiple subsystems, similar to those that may be implemented on future vehicles. The best approach is defined as one that most minimizes computational resource requirements without impacting the detection of sensor failures.

Single Photon Counting Performance and Noise Analysis of CMOS SPAD-Based Image Sensors

PubMed Central

Dutton, Neale A. W.; Gyongy, Istvan; Parmesan, Luca; Henderson, Robert K.

2016-01-01

SPAD-based solid state CMOS image sensors utilising analogue integrators have attained deep sub-electron read noise (DSERN) permitting single photon counting (SPC) imaging. A new method is proposed to determine the read noise in DSERN image sensors by evaluating the peak separation and width (PSW) of single photon peaks in a photon counting histogram (PCH). The technique is used to identify and analyse cumulative noise in analogue integrating SPC SPAD-based pixels. The DSERN of our SPAD image sensor is exploited to confirm recent multi-photon threshold quanta image sensor (QIS) theory. Finally, various single and multiple photon spatio-temporal oversampling techniques are reviewed. PMID:27447643

Woven electrochemical fabric-based test sensors (WEFTS): a new class of multiplexed electrochemical sensors.

PubMed

Choudhary, Tripurari; Rajamanickam, G P; Dendukuri, Dhananjaya

2015-05-07

We present textile weaving as a new technique for the manufacture of miniature electrochemical sensors with significant advantages over current fabrication techniques. Biocompatible silk yarn is used as the material for fabrication instead of plastics and ceramics used in commercial sensors. Silk yarns are coated with conducting inks and reagents before being handloom-woven as electrodes into patches of fabric to create arrays of sensors, which are then laminated, cut and packaged into individual sensors. Unlike the conventionally used screen-printing, which results in wastage of reagents, yarn coating uses only as much reagent and ink as required. Hydrophilic and hydrophobic yarns are used for patterning so that sample flow is restricted to a small area of the sensor. This simple fluidic control is achieved with readily available materials. We have fabricated and validated individual sensors for glucose and hemoglobin and a multiplexed sensor, which can detect both analytes. Chronoamperometry and differential pulse voltammetry (DPV) were used to detect glucose and hemoglobin, respectively. Industrial quantities of these sensors can be fabricated at distributed locations in the developing world using existing skills and manufacturing facilities. We believe such sensors could find applications in the emerging area of wearable sensors for chemical testing.

Sensor Fusion and Smart Sensor in Sports and Biomedical Applications

PubMed Central

Mendes, José Jair Alves; Vieira, Mário Elias Marinho; Pires, Marcelo Bissi; Stevan, Sergio Luiz

2016-01-01

The following work presents an overview of smart sensors and sensor fusion targeted at biomedical applications and sports areas. In this work, the integration of these areas is demonstrated, promoting a reflection about techniques and applications to collect, quantify and qualify some physical variables associated with the human body. These techniques are presented in various biomedical and sports applications, which cover areas related to diagnostics, rehabilitation, physical monitoring, and the development of performance in athletes, among others. Although some applications are described in only one of two fields of study (biomedicine and sports), it is very likely that the same application fits in both, with small peculiarities or adaptations. To illustrate the contemporaneity of applications, an analysis of specialized papers published in the last six years has been made. In this context, the main characteristic of this review is to present the largest quantity of relevant examples of sensor fusion and smart sensors focusing on their utilization and proposals, without deeply addressing one specific system or technique, to the detriment of the others. PMID:27669260

Enhanced Strain Measurement Range of an FBG Sensor Embedded in Seven-Wire Steel Strands.

PubMed

Kim, Jae-Min; Kim, Chul-Min; Choi, Song-Yi; Lee, Bang Yeon

2017-07-18

FBG sensors offer many advantages, such as a lack of sensitivity to electromagnetic waves, small size, high durability, and high sensitivity. However, their maximum strain measurement range is lower than the yield strain range (about 1.0%) of steel strands when embedded in steel strands. This study proposes a new FBG sensing technique in which an FBG sensor is recoated with polyimide and protected by a polyimide tube in an effort to enhance the maximum strain measurement range of FBG sensors embedded in strands. The validation test results showed that the proposed FBG sensing technique has a maximum strain measurement range of 1.73% on average, which is 1.73 times higher than the yield strain of the strands. It was confirmed that recoating the FBG sensor with polyimide and protecting the FBG sensor using a polyimide tube could effectively enhance the maximum strain measurement range of FBG sensors embedded in strands.

Holographic detection of hydrocarbon gases and other volatile organic compounds.

PubMed

Martínez-Hurtado, J L; Davidson, C A B; Blyth, J; Lowe, C R

2010-10-05

There is a need to develop sensors for real-time monitoring of volatile organic compounds (VOCs) and hydrocarbon gases in both external and indoor environments, since these compounds are of growing concern in human health and welfare. Current measurement technology for VOCs requires sophisticated equipment and lacks the prospect for rapid real-time monitoring. Holographic sensors can give a direct reading of the analyte concentration as a color change. We report a technique for recording holographic sensors by laser ablation of silver particles formed in situ by diffusion. This technique allows a readily available hydrophobic silicone elastomer to be transformed into an effective sensor for hydrocarbon gases and other volatile compounds. The intermolecular interactions present between the polymer and molecules are used to predict the sensor performance. The hydrophobicity of this material allows the sensor to operate without interference from water and other atmospheric gases and thus makes the sensor suitable for biomedical, industrial, or environmental analysis.

Innovative smart micro sensors for Army weaponry applications

NASA Astrophysics Data System (ADS)

Ruffin, Paul B.; Brantley, Christina; Edwards, Eugene

2008-03-01

Micro sensors offer the potential solution to cost, size, and weight issues associated with smart networked sensor systems designed for environmental/missile health monitoring and rocket out-gassing/fuel leak detection, as well as situational awareness on the battlefield. In collaboration with the University of Arkansas (Fayetteville), University of Alabama (Tuscaloosa and Birmingham), Alabama A&M University (Normal), and Streamline Automation (Huntsville, AL), scientists and engineers at the Army Aviation & Missile Research, Development, and Engineering Center (AMRDEC) are investigating several nano-based technologies to solve the problem of sensing extremely small levels of toxic gases associated with both chemical warfare agents (in air and liquids) and potential rocket motor leaks. Innovative techniques are being devised to adapt voltammetry, which is a well established technique for the detection and quantification of substances dissolved in liquids, to low-cost micro sensors for detecting airborne chemical agents and potential missile propellant leakages. In addition, a surface enhanced Raman scattering (SERS) technique, which enhances Raman scattered light by excitation of surface plasmons on nanoporous metal surfaces (nanospheres), is being investigated to develop novel smart sensors for the detection of chemical agents (including rocket motor out-gassing) and potential detection of home-made explosive devices. In this paper, results are delineated that are associated with experimental studies, which are conducted for the aforementioned cases and for several other nano-based technology approaches. The design challenges of each micro sensor technology approach are discussed. Finally, a comparative analysis of the various innovative micro-sensor techniques is provided.

Non-Destructive Techniques Based on Eddy Current Testing

PubMed Central

García-Martín, Javier; Gómez-Gil, Jaime; Vázquez-Sánchez, Ernesto

2011-01-01

Non-destructive techniques are used widely in the metal industry in order to control the quality of materials. Eddy current testing is one of the most extensively used non-destructive techniques for inspecting electrically conductive materials at very high speeds that does not require any contact between the test piece and the sensor. This paper includes an overview of the fundamentals and main variables of eddy current testing. It also describes the state-of-the-art sensors and modern techniques such as multi-frequency and pulsed systems. Recent advances in complex models towards solving crack-sensor interaction, developments in instrumentation due to advances in electronic devices, and the evolution of data processing suggest that eddy current testing systems will be increasingly used in the future. PMID:22163754

Non-destructive techniques based on eddy current testing.

PubMed

García-Martín, Javier; Gómez-Gil, Jaime; Vázquez-Sánchez, Ernesto

2011-01-01

Non-destructive techniques are used widely in the metal industry in order to control the quality of materials. Eddy current testing is one of the most extensively used non-destructive techniques for inspecting electrically conductive materials at very high speeds that does not require any contact between the test piece and the sensor. This paper includes an overview of the fundamentals and main variables of eddy current testing. It also describes the state-of-the-art sensors and modern techniques such as multi-frequency and pulsed systems. Recent advances in complex models towards solving crack-sensor interaction, developments in instrumentation due to advances in electronic devices, and the evolution of data processing suggest that eddy current testing systems will be increasingly used in the future.

Recent Advances of MEMS Resonators for Lorentz Force Based Magnetic Field Sensors: Design, Applications and Challenges.

PubMed

Herrera-May, Agustín Leobardo; Soler-Balcazar, Juan Carlos; Vázquez-Leal, Héctor; Martínez-Castillo, Jaime; Vigueras-Zuñiga, Marco Osvaldo; Aguilera-Cortés, Luz Antonio

2016-08-24

Microelectromechanical systems (MEMS) resonators have allowed the development of magnetic field sensors with potential applications such as biomedicine, automotive industry, navigation systems, space satellites, telecommunications and non-destructive testing. We present a review of recent magnetic field sensors based on MEMS resonators, which operate with Lorentz force. These sensors have a compact structure, wide measurement range, low energy consumption, high sensitivity and suitable performance. The design methodology, simulation tools, damping sources, sensing techniques and future applications of magnetic field sensors are discussed. The design process is fundamental in achieving correct selection of the operation principle, sensing technique, materials, fabrication process and readout systems of the sensors. In addition, the description of the main sensing systems and challenges of the MEMS sensors are discussed. To develop the best devices, researches of their mechanical reliability, vacuum packaging, design optimization and temperature compensation circuits are needed. Future applications will require multifunctional sensors for monitoring several physical parameters (e.g., magnetic field, acceleration, angular ratio, humidity, temperature and gases).

Recent Advances of MEMS Resonators for Lorentz Force Based Magnetic Field Sensors: Design, Applications and Challenges

PubMed Central

Herrera-May, Agustín Leobardo; Soler-Balcazar, Juan Carlos; Vázquez-Leal, Héctor; Martínez-Castillo, Jaime; Vigueras-Zuñiga, Marco Osvaldo; Aguilera-Cortés, Luz Antonio

2016-01-01

Microelectromechanical systems (MEMS) resonators have allowed the development of magnetic field sensors with potential applications such as biomedicine, automotive industry, navigation systems, space satellites, telecommunications and non-destructive testing. We present a review of recent magnetic field sensors based on MEMS resonators, which operate with Lorentz force. These sensors have a compact structure, wide measurement range, low energy consumption, high sensitivity and suitable performance. The design methodology, simulation tools, damping sources, sensing techniques and future applications of magnetic field sensors are discussed. The design process is fundamental in achieving correct selection of the operation principle, sensing technique, materials, fabrication process and readout systems of the sensors. In addition, the description of the main sensing systems and challenges of the MEMS sensors are discussed. To develop the best devices, researches of their mechanical reliability, vacuum packaging, design optimization and temperature compensation circuits are needed. Future applications will require multifunctional sensors for monitoring several physical parameters (e.g., magnetic field, acceleration, angular ratio, humidity, temperature and gases). PMID:27563912

Turbine blade and vane heat flux sensor development, phase 1

NASA Technical Reports Server (NTRS)

Atkinson, W. H.; Cyr, M. A.; Strange, R. R.

1984-01-01

Heat flux sensors available for installation in the hot section airfoils of advanced aircraft gas turbine engines were developed. Two heat flux sensors were designed, fabricated, calibrated, and tested. Measurement techniques are compared in an atmospheric pressure combustor rig test. Sensors, embedded thermocouple and the Gordon gauge, were fabricated that met the geometric and fabricability requirements and could withstand the hot section environmental conditions. Calibration data indicate that these sensors yielded repeatable results and have the potential to meet the accuracy goal of measuring local heat flux to within 5%. Thermal cycle tests and thermal soak tests indicated that the sensors are capable of surviving extended periods of exposure to the environment conditions in the turbine. Problems in calibration of the sensors caused by severe non-one dimensional heat flow were encountered. Modifications to the calibration techniques are needed to minimize this problem and proof testing of the sensors in an engine is needed to verify the designs.

Turbine blade and vane heat flux sensor development, phase 1

NASA Astrophysics Data System (ADS)

Atkinson, W. H.; Cyr, M. A.; Strange, R. R.

1984-08-01

Heat flux sensors available for installation in the hot section airfoils of advanced aircraft gas turbine engines were developed. Two heat flux sensors were designed, fabricated, calibrated, and tested. Measurement techniques are compared in an atmospheric pressure combustor rig test. Sensors, embedded thermocouple and the Gordon gauge, were fabricated that met the geometric and fabricability requirements and could withstand the hot section environmental conditions. Calibration data indicate that these sensors yielded repeatable results and have the potential to meet the accuracy goal of measuring local heat flux to within 5%. Thermal cycle tests and thermal soak tests indicated that the sensors are capable of surviving extended periods of exposure to the environment conditions in the turbine. Problems in calibration of the sensors caused by severe non-one dimensional heat flow were encountered. Modifications to the calibration techniques are needed to minimize this problem and proof testing of the sensors in an engine is needed to verify the designs.

Effect of monensin on in vitro fermentation of silages and microbial protein synthesis.

PubMed

Wischer, Gerald; Boguhn, Jeannette; Steingaß, Herbert; Schollenberger, Margit; Hartung, Karin; Rodehutscord, Markus

2013-06-01

The objective of the study was to investigate the effects of monensin on silage fermentation and microbial net protein synthesis. In Experiment 1, monensin (0.5, 1, 2, 4, 6, or 10 µg) was added to syringes that contained 120 mg of grass silage (GS), grass silage and concentrate (GS + C), or maize silage (MS), resulting in concentrations of 4.2, 8.3, 16.7, 33.3, 50.0 and 83.3 mg monensin/kg feed. Samples were incubated for 24 h to determine the monensin concentration that resulted in the maximum reduction in methane production without effects on the total gas production. In Experiment 2, GS and GS + C were incubated in a rumen simulation technique (Rusitec) to assess the monensin effects (133 and 266 mg/kg feed) on the production of total gas, methane and volatile fatty acids (VFA), degradation of nutrients and microbial net protein synthesis. In Experiment 1, methane production was reduced without significant effects on the total gas production; the reductions were 17% (GS), 10% (GS + C) and 13% (MS) with 16.7 (GS), 50.0 (GS + C) and 33.3 (MS) mg monensin/kg feed. Monensin reduced the total gas and methane production in GS and GS + C in Experiment 2. Propionate production was enhanced by monensin, accompanied by a decrease in acetate production. Along with a reduction in crude protein (CP) degradation, monensin reduced the ammonia nitrogen concentration in the effluent of both treatments. While the protein produced by liquid-associated microbes increased with monensin, protein production by solid-associated microbes was reduced. Total microbial net protein synthesis increased in the presence of monensin. Monensin influenced the production of total gas, methane and VFA from the silages without an effect on the degradation of organic matter (OM). Different microbial fractions were affected differently by monensin supplementation. If monensin is used as a tool to reduce methane emission, the supplementation level must be carefully chosen to avoid negative effects on overall fermentation in the rumen.

Multimodal technique to eliminate humidity interference for specific detection of ethanol.

PubMed

Jalal, Ahmed Hasnain; Umasankar, Yogeswaran; Gonzalez, Pablo J; Alfonso, Alejandro; Bhansali, Shekhar

2017-01-15

Multimodal electrochemical technique incorporating both open circuit potential (OCP) and amperometric techniques have been conceptualized and implemented to improve the detection of specific analyte in systems where more than one analyte is present. This approach has been demonstrated through the detection of ethanol while eliminating the contribution of water in a micro fuel cell sensor system. The sensor was interfaced with LMP91000 potentiostat, controlled through MSP430F5529LP microcontroller to implement an auto-calibration algorithm tailored to improve the detection of alcohol. The sensor was designed and fabricated as a three electrode system with Nafion as a proton exchange membrane (PEM). The electrochemical signal of the interfering phase (water) was eliminated by implementing the multimodal electrochemical detection technique. The results were validated by comparing sensor and potentiostat performances with a commercial sensor and potentiostat respectively. The results suggest that such a sensing system can detect ethanol at concentrations as low as 5ppm. The structure and properties such as low detection limit, selectivity and miniaturized size enables potential application of this device in wearable transdermal alcohol measurements. Copyright © 2016 Elsevier B.V. All rights reserved.

Localization of a continuous CO2 leak from an isotropic flat-surface structure using acoustic emission detection and near-field beamforming techniques

NASA Astrophysics Data System (ADS)

Yan, Yong; Cui, Xiwang; Guo, Miao; Han, Xiaojuan

2016-11-01

Seal capacity is of great importance for the safety operation of pressurized vessels. It is crucial to locate the leak hole timely and accurately for reasons of safety and maintenance. This paper presents the principle and application of a linear acoustic emission sensor array and a near-field beamforming technique to identify the location of a continuous CO2 leak from an isotropic flat-surface structure on a pressurized vessel in the carbon capture and storage system. Acoustic signals generated by the leak hole are collected using a linear high-frequency sensor array. Time-frequency analysis and a narrow-band filtering technique are deployed to extract effective information about the leak. The impacts of various factors on the performance of the localization technique are simulated, compared and discussed, including the number of sensors, distance between the leak hole and sensor array and spacing between adjacent sensors. Experiments were carried out on a laboratory-scale test rig to assess the effectiveness and operability of the proposed method. The results obtained suggest that the proposed method is capable of providing accurate and reliable localization of a continuous CO2 leak.

Stripe-PZT Sensor-Based Baseline-Free Crack Diagnosis in a Structure with a Welded Stiffener.

PubMed

An, Yun-Kyu; Shen, Zhiqi; Wu, Zhishen

2016-09-16

This paper proposes a stripe-PZT sensor-based baseline-free crack diagnosis technique in the heat affected zone (HAZ) of a structure with a welded stiffener. The proposed technique enables one to identify and localize a crack in the HAZ using only current data measured using a stripe-PZT sensor. The use of the stripe-PZT sensor makes it possible to significantly improve the applicability to real structures and minimize man-made errors associated with the installation process by embedding multiple piezoelectric sensors onto a printed circuit board. Moreover, a new frequency-wavenumber analysis-based baseline-free crack diagnosis algorithm minimizes false alarms caused by environmental variations by avoiding simple comparison with the baseline data accumulated from the pristine condition of a target structure. The proposed technique is numerically as well as experimentally validated using a plate-like structure with a welded stiffener, reveling that it successfully identifies and localizes a crack in HAZ.

Stripe-PZT Sensor-Based Baseline-Free Crack Diagnosis in a Structure with a Welded Stiffener

PubMed Central

An, Yun-Kyu; Shen, Zhiqi; Wu, Zhishen

2016-01-01

This paper proposes a stripe-PZT sensor-based baseline-free crack diagnosis technique in the heat affected zone (HAZ) of a structure with a welded stiffener. The proposed technique enables one to identify and localize a crack in the HAZ using only current data measured using a stripe-PZT sensor. The use of the stripe-PZT sensor makes it possible to significantly improve the applicability to real structures and minimize man-made errors associated with the installation process by embedding multiple piezoelectric sensors onto a printed circuit board. Moreover, a new frequency-wavenumber analysis-based baseline-free crack diagnosis algorithm minimizes false alarms caused by environmental variations by avoiding simple comparison with the baseline data accumulated from the pristine condition of a target structure. The proposed technique is numerically as well as experimentally validated using a plate-like structure with a welded stiffener, reveling that it successfully identifies and localizes a crack in HAZ. PMID:27649200

Fiber Optic Bragg Grating Sensors for Thermographic Detection of Subsurface Anomalies

NASA Technical Reports Server (NTRS)

Allison, Sidney G.; Winfree, William P.; Wu, Meng-Chou

2009-01-01

Conventional thermography with an infrared imager has been shown to be an extremely viable technique for nondestructively detecting subsurface anomalies such as thickness variations due to corrosion. A recently developed technique using fiber optic sensors to measure temperature holds potential for performing similar inspections without requiring an infrared imager. The structure is heated using a heat source such as a quartz lamp with fiber Bragg grating (FBG) sensors at the surface of the structure to detect temperature. Investigated structures include a stainless steel plate with thickness variations simulated by small platelets attached to the back side using thermal grease. A relationship is shown between the FBG sensor thermal response and variations in material thickness. For comparison, finite element modeling was performed and found to agree closely with the fiber optic thermography results. This technique shows potential for applications where FBG sensors are already bonded to structures for Integrated Vehicle Health Monitoring (IVHM) strain measurements and can serve dual-use by also performing thermographic detection of subsurface anomalies.

INNOVATIVE EASY-TO-USE PASSIVE TECHNIQUE FOR 222RN AND 220RN DECAY PRODUCT DETECTION.

PubMed

Mishra, Rosaline; Rout, R; Prajith, R; Jalalluddin, S; Sapra, B K; Mayya, Y S

2016-10-01

The decay products of radon and thoron are essentially the radioisotopes of polonium, bismuth and lead, and are solid particulates, which deposit in different parts of the respiratory tract upon inhalation, subsequently emitting high-energy alpha particles upon their radioactive decay. Development of passive deposition-based direct progeny sensors known as direct radon and thoron progeny sensors have provided an easy-to-use technique for time-integrated measurements of the decay products only. These dosemeters are apt for large-scale population dosimetry to assign inhalation doses to the public. The paper gives an insight into the technique, the calibration, comparison with the prevalently used active grab filter paper sampling technique, alpha track diameter analysis in these progeny sensors, progeny deposition velocity measurements carried out using these detector systems in the indoor as well as outdoor environment, and applications of these sensors for time-integrated unattached fraction estimation. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Polarization interferometry for real-time spectroscopic plasmonic sensing.

PubMed

Otto, Lauren M; Mohr, Daniel A; Johnson, Timothy W; Oh, Sang-Hyun; Lindquist, Nathan C

2015-03-07

We present quantitative, spectroscopic polarization interferometry phase measurements on plasmonic surfaces for sensing applications. By adding a liquid crystal variable wave plate in our beam path, we are able to measure phase shifts due to small refractive index changes on the sensor surface. By scanning in a quick sequence, our technique is extended to demonstrate real-time measurements. While this optical technique is applicable to different sensor geometries-e.g., nanoparticles, nanogratings, or nanoapertures-the plasmonic sensors we use here consist of an ultrasmooth gold layer with buried linear gratings. Using these devices and our phase measurement technique, we calculate a figure of merit that shows improvement over measuring only surface plasmon resonance shifts from a reflected intensity spectrum. To demonstrate the general-purpose versatility of our phase-resolved measurements, we also show numerical simulations with another common device architecture: periodic plasmonic slits. Since our technique inherently measures both the intensity and phase of the reflected or transmitted light simultaneously, quantitative sensor device characterization is possible.

Effect of starchy or fibrous carbohydrate supplementation of an herbage diet on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

A 4-unit dual-flow continuous culture fermentor system was used to assess the effect of supplementing 2 levels (5 and 10% of diet DM) of starchy (barley grain: BAR) or fibrous (beet pulp: BP) carbohydrate (CHO) to an orchardgrass diet on nutrient digestibility, VFA production, bacterial protein synt...

Edible Oil Barriers for Treatment of Chlorinated Solvent Contaminated Groundwater

DTIC Science & Technology

2009-07-01

CF Chloroform Cl# Chlorine Number CO Carbon Monoxide CT Carbon Tetrachloride CVOC Chlorinated Volatile Organic Compound 1,2-DCA 1,2...As Safe HCl Hydrochloric Acid HRC® Hydrogen Release Compound IDW Investigation-Derived Waste ISCO In Situ Chemical Oxidation LEL Lower...Total Organic Carbon VC Vinyl Chloride VFA Volatile Fatty Acid VOC Volatile Organic Compound ZVI Zero Valent Iron viii ACKNOWLEDGEMENTS

Deontic Modals in RP-US Visiting Forces Agreement (VFA): A Corpus-Based Analysis

ERIC Educational Resources Information Center

Dela Rosa, John Paul Obillos

2017-01-01

The marriage between language and the law is apparent in any legal document of whatever purpose. Hence, at present, studies on the language of the law are definitely in vogue. Grounded on Quirk et al. (1985) and Matulewska's (2010) description of deontic modality, this corpus-based linguistic study aimed at analyzing the use of deontic modals in…

Clorate Metabolism in Pure Cultures of E.Coli 0157:H7 Pretreated with Either Nitrate or Chlorate

USDA-ARS?s Scientific Manuscript database

Experiments were conducted to determine the effects of 5, 7.5, and 10 mM nitrate, and 5, 10, or 20 mM chlorate on total E. coli counts, chlorate metabolism, and volatile fatty acid (VFA) concentrations in anaerobic ruminal fluid cultures. Nitrate did not affect total E. coli counts (P = 0.05), chlor...

Acute exposure to ergot alkaloids from endophyte-infected tall fescue does not alter absorptive or barrier function of the isolated ruminal epithelium

USDA-ARS?s Scientific Manuscript database

Ergot alkaloids in endophyte-infected (Neotyphodium coenophialum) tall fescue (Lolium arundinaceum) have been shown to cause a reduction in blood flow to the rumen epithelium as well as a decrease in VFA absorption from the washed rumen of steers. Previous data also indicates that incubating an extr...

Effect of starchy or fibrous carbohydrate supplementation of an herbage diet on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

A dual-flow continuous culture fermentor system was used to assess the effect of supplementing 2 levels (5 or 10% of diet DM) of starchy (barley: BAR) or fibrous (beet pulp: BP) carbohydrate (CHO) to an orchardgrass diet on nutrient digestibility, VFA production, bacterial protein synthesis, and met...

Effect of sprouted barley grain supplementation of an herbage-based or haylage-based diet on ruminal fermentation and methane output in continuous culture

USDA-ARS?s Scientific Manuscript database

A 4-unit dual-flow continuous culture fermentor system was used to assess the effect of supplementing 7-d sprouted barley (SB) or barley grain (BG) with an herbage-based or haylage-based diet on nutrient digestibility, volatile fatty acid (VFA) profiles, bacterial protein synthesis, and methane outp...

Rumen fluid fermentation for enhancement of hydrolysis and acidification of grass clipping.

PubMed

Wang, Siqi; Zhang, Guangming; Zhang, Panyue; Ma, Xiaowen; Li, Fan; Zhang, Haibo; Tao, Xue; Ye, Junpei; Nabi, Mohammad

2018-08-15

Rumen fluid, formed in rumen of ruminants, includes a complex microbial population of bacteria, protozoa, fungi and archaea, and has high ability to degrade lignocellulosic biomass. In this study, rumen fluid was used to ferment grass clipping for enhancing the hydrolysis and acidification of organic matters. Results showed that strict anaerobic condition, higher grass clipping content and smaller particle size of grass clipping were beneficial to the hydrolysis and acidification of organics. The increase of SCOD and total VFA concentration respectively reached 24.9 and 10.2 g/L with a suitable grass clipping content of 5%, a particle size <0.150 mm, and a fermentation time of 48 h. The VFA production was mainly attributed to the degradation of cellulose and hemicellulose with a total solid reduction of 55.7%. Firmicutes and Fibrobacteres were the major contributors to the degradation of cellulose and hemicellulose. The activity of carboxymethyl cellulose enzyme (CMCase), cellobiase and xylanase reached 0.027, 0.176 and 0.180 U/ml, respectively. The rumen fluid microorganisms successfully enhanced the hydrolysis and acidification of grass clipping. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparative Analysis of Performance and Microbial Characteristics Between High-Solid and Low-Solid Anaerobic Digestion of Sewage Sludge Under Mesophilic Conditions.

PubMed

Lu, Qin; Yi, Jing; Yang, Dianhai

2016-01-01

High-solid anaerobic digestion of sewage sludge achieves highly efficient volatile solid reduction, and production of volatile fatty acid (VFA) and methane compared with conventional low-solid anaerobic digestion. In this study, the potential mechanisms of the better performance in high-solid anaerobic digestion of sewage sludge were investigated by using 454 high-throughput pyrosequencing and real-time PCR to analyze the microbial characteristics in sewage sludge fermentation reactors. The results obtained by 454 high-throughput pyrosequencing revealed that the phyla Chloroflexi, Bacteroidetes, and Firmicutes were the dominant functional microorganisms in high-solid and low-solid anaerobic systems. Meanwhile, the real-time PCR assays showed that high-solid anaerobic digestion significantly increased the number of total bacteria, which enhanced the hydrolysis and acidification of sewage sludge. Further study indicated that the number of total archaea (dominated by Methanosarcina) in a high-solid anaerobic fermentation reactor was also higher than that in a low-solid reactor, resulting in higher VFA consumption and methane production. Hence, the increased key bacteria and methanogenic archaea involved in sewage sludge hydrolysis, acidification, and methanogenesis resulted in the better performance of high-solid anaerobic sewage sludge fermentation.

Co-digestion of manure and industrial waste--The effects of trace element addition.

PubMed

Nordell, Erik; Nilsson, Britt; Nilsson Påledal, Sören; Karisalmi, Kaisa; Moestedt, Jan

2016-01-01

Manure is one of the most common substrates for biogas production. Manure from dairy- and swine animals are often considered to stabilize the biogas process by contributing nutrients and trace elements needed for the biogas process. In this study two lab-scale reactors were used to evaluate the effects of trace element addition during co-digestion of manure from swine- and dairy animals with industrial waste. The substrate used contained high background concentrations of both cobalt and nickel, which are considered to be the most important trace elements. In the reactor receiving additional trace elements, the volatile fatty acids (VFA) concentration was 89% lower than in the control reactor. The lower VFA concentration contributed to a more digested digestate, and thus lower methane emissions in the subsequent storage. Also, the biogas production rate increased with 24% and the biogas production yield with 10%, both as a result of the additional trace elements at high organic loading rates. All in all, even though 50% of the feedstock consisted of manure, trace element addition resulted in multiple positive effects and a more reliable process with stable and high yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of urea treatment of cocoa pod on rumen fermentation characteristics in vitro

NASA Astrophysics Data System (ADS)

Anggraeni, A. S.; Herdian, H.; Sakti, A. A.; Sofyan, A.; Ekaningrum, M.

2017-12-01

Indonesia is a third largest country in the world for cocoa production. A cocoa pod could be utilized as alternative feeds due to their sufficient quantity and availability throughout the year. On the other hand, low nutritional quality such as highly fibrous materials and low protein content usually characterized in agricultural and plantation by-products as it appears on cocoa pod. Ammoniation treatment using urea improve the nutritional quality of feedstuff. The objective of this study was to evaluate the effect of ammoniation treatments on a cocoa pod on in vitro feed fermentation and gas production on ruminal fluid. KA treatment gave highest gas production than other treatment. Total gas production during 48 hours of the cocoa pod was significantly affected by treatments (P<0.05). Total volatile acid (VFA), acetate (C2), propionate (C3), butyrate (C4) total VFA and A/P ratio indicated no significant difference among treatments. KA and KD treatments have tendency effect on IVDMD than control (KS) treatment. In this study ammoniation treatment using 5% of urea had a positive and effect on the best degradability and ruminal fermentation of cocoa pod.

Effects of Whole Grain Wheat Bread on Visceral Fat Obesity in Japanese Subjects: A Randomized Double-Blind Study.

PubMed

Kikuchi, Yosuke; Nozaki, Satomi; Makita, Miki; Yokozuka, Shoji; Fukudome, Shin-Ichi; Yanagisawa, Takashi; Aoe, Seiichiro

2018-04-18

Metabolic syndrome is a risk factor for cardiovascular diseases and has become increasingly common in Japan. Epidemiological studies show inverse associations between intake of whole wheat grains and metabolic syndrome, but few dietary intervention trials have investigated the effect of whole wheat grain consumption. It was investigated whether a diet in which refined wheat bread (RW diet) was substituted by whole grain wheat bread (WW diet) would reduce visceral fat obesity in Japanese subjects. A randomized double-blind placebo-controlled intervention study was conducted in 50 Japanese subjects with body mass index (BMI) ≥ 23 kg/m 2 . Subjects were randomly assigned WW (WW group) or RW diets (RW group) for 12 weeks. Blood samples and computed tomography scans were obtained every 6th week. The WW group showed decrease (-4 cm 2 ) in visceral fat area (VFA) (p < 0.05), whereas the RW group showed no significant changes. These time-dependent changes were significantly different between the groups. WW diet led to significant and safe reductions in VFA in subjects with BMI ≥ 23 kg/m 2 . WW diet may contribute to preventing visceral fat obesity.

Conventional and thermophilic aerobic treatability of high strength oily pet food wastewater using membrane-coupled bioreactors.

PubMed

Kurian, R; Acharya, C; Nakhla, G; Bassi, A

2005-11-01

Although thermophilic treatment systems have recently gained considerable interest, limited information exists on the comparative performances of membrane-coupled bioreactors (MBR) at thermophilic and conventional conditions. In this study aerobic MBRs operating at room temperature (20 degrees C) and at lower thermophilic range (45 degrees C) were investigated for the treatment of dissolved air flotation (DAF) pretreated pet food wastewater. The particular wastewater is characterized by oil and grease (O & G) concentrations as high as 6 g/L, COD of 51 g/L, BOD of 16 g/L and volatile fatty acid (VFA) of 8.3 g/L. The performances of the two systems in terms of COD, BOD and O & G removal at varying hydraulic retention time (HRT) are compared. COD removal efficiencies in the thermophilic MBR varied from 75% to 98% and remained constant at 94% in the conventional MBR. The O & G removal efficiencies were 66-86% and 98% in the thermophilic and conventional MBR, respectively. Interestingly, high concentrations of VFA were recorded, equivalent to 50-73% of total COD, in the thermophilic MBR effluent. The observed yield in the thermophilic MBR was 40% of that observed in the conventional MBR.

Performance and kinetic evaluation of semi-continuously fed anaerobic digesters treating food waste: role of trace elements.

PubMed

Zhang, Wanqin; Wu, Shubiao; Guo, Jianbin; Zhou, Jie; Dong, Renjie

2015-02-01

This study investigated the effects of trace elements (TEs) on the anaerobic digestion (AD) of food waste (FW) in laboratory-scale semi-continuously fed anaerobic digesters. The duration of digesters operation was approximately 400 days. Organic loading rates (OLRs) ranged from 1.0 to 5.5 g VS L(-1) d(-1) at 37 °C. Results showed that methane production of the digester was severely inhibited at a volatile fatty acid (VFA) concentration of 30,000 mg L(-1) at OLR of 4.0 g VS L(-1) d(-1) in the absence of TEs. Contrary to the failed digesters, a stable performance was achieved in the TEs added digesters. High methane yield (approximately 465.4 mL CH4 g(-1)VSadded) was obtained, and no significant accumulation of VFA was observed in the TEs added digesters at OLR of 1.0-5.0 g VS L(-1) d(-1) and HRT of 40 days. These findings strongly indicated that the addition of TEs has an important impact on the operation stability of AD of FW. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of mixing ratio of food waste and rice husk co-digestion and substrate to inoculum ratio on biogas production.

PubMed

Haider, Muhammad Rizwan; Zeshan; Yousaf, Sohail; Malik, Riffat Naseem; Visvanathan, Chettiyappan

2015-08-01

Aim of this study was to find out suitable mixing ratio of food waste and rice husk for their co-digestion in order to overcome VFA accumulation in digestion of food waste alone. Four mixing ratios of food waste and rice husk with C/N ratios of 20, 25, 30 and 35 were subjected to a lab scale anaerobic batch experiment under mesophilic conditions. Highest specific biogas yield of 584L/kgVS was obtained from feedstock with C/N ratio of 20. Biogas yield decreased with decrease in food waste proportion. Further, fresh cow dung was used as inoculum to investigate optimum S/I ratio with the selected feedstock. In experiment 2, feedstock with C/N ratio 20 was subjected to anaerobic digestion at five S/I ratios of 0.25, 0.5, 1.0, 1.5 and 2.0. Specific biogas yield of 557L/kgVS was obtained at S/I ratio of 0.25. However, VFA accumulation occurred at higher S/I ratios due to higher organic loadings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Multi-Source Sensor Fusion for Small Unmanned Aircraft Systems Using Fuzzy Logic

NASA Technical Reports Server (NTRS)

Cook, Brandon; Cohen, Kelly

2017-01-01

As the applications for using small Unmanned Aircraft Systems (sUAS) beyond visual line of sight (BVLOS) continue to grow in the coming years, it is imperative that intelligent sensor fusion techniques be explored. In BVLOS scenarios the vehicle position must accurately be tracked over time to ensure no two vehicles collide with one another, no vehicle crashes into surrounding structures, and to identify off-nominal scenarios. Therefore, in this study an intelligent systems approach is used to estimate the position of sUAS given a variety of sensor platforms, including, GPS, radar, and on-board detection hardware. Common research challenges include, asynchronous sensor rates and sensor reliability. In an effort to realize these challenges, techniques such as a Maximum a Posteriori estimation and a Fuzzy Logic based sensor confidence determination are used.

Hysteresis compensation technique applied to polymer optical fiber curvature sensor for lower limb exoskeletons

NASA Astrophysics Data System (ADS)

Gomes Leal-Junior, Arnaldo; Frizera-Neto, Anselmo; José Pontes, Maria; Rodrigues Botelho, Thomaz

2017-12-01

Polymer optical fiber (POF) curvature sensors present some advantages over conventional techniques for angle measurements, such as their light weight, compactness and immunity to electromagnetic fields. However, high hysteresis can occur in POF curvature sensors due to the polymer viscoelastic response. In order to overcome this limitation, this paper shows how the hysteresis sensor can be compensated by a calibration equation relating the measured output signal to the sensor’s angular velocity. The proposed method is validated using an exoskeleton with an active joint on the knee for flexion and extension rehabilitation exercises. The results show a decrease in sensor hysteresis and a decrease by more than two times in the error between the POF sensor and the potentiometer, which is employed for the angle measurement of the exoskeleton knee joint.

Recent Advances in Paper-Based Sensors

PubMed Central

Liana, Devi D.; Raguse, Burkhard; Gooding, J. Justin; Chow, Edith

2012-01-01

Paper-based sensors are a new alternative technology for fabricating simple, low-cost, portable and disposable analytical devices for many application areas including clinical diagnosis, food quality control and environmental monitoring. The unique properties of paper which allow passive liquid transport and compatibility with chemicals/biochemicals are the main advantages of using paper as a sensing platform. Depending on the main goal to be achieved in paper-based sensors, the fabrication methods and the analysis techniques can be tuned to fulfill the needs of the end-user. Current paper-based sensors are focused on microfluidic delivery of solution to the detection site whereas more advanced designs involve complex 3-D geometries based on the same microfluidic principles. Although paper-based sensors are very promising, they still suffer from certain limitations such as accuracy and sensitivity. However, it is anticipated that in the future, with advances in fabrication and analytical techniques, that there will be more new and innovative developments in paper-based sensors. These sensors could better meet the current objectives of a viable low-cost and portable device in addition to offering high sensitivity and selectivity, and multiple analyte discrimination. This paper is a review of recent advances in paper-based sensors and covers the following topics: existing fabrication techniques, analytical methods and application areas. Finally, the present challenges and future outlooks are discussed. PMID:23112667

Long fiber Bragg grating sensor interrogation using discrete-time microwave photonic filtering techniques.

PubMed

Ricchiuti, Amelia Lavinia; Barrera, David; Sales, Salvador; Thevenaz, Luc; Capmany, José

2013-11-18

A novel technique for interrogating photonic sensors based on long fiber Bragg gratings (FBGs) is presented and experimentally demonstrated, dedicated to detect the presence and the precise location of several spot events. The principle of operation is based on a technique used to analyze microwave photonics (MWP) filters. The long FBGs are used as quasi-distributed sensors. Several hot-spots can be detected along the FBG with a spatial accuracy under 0.5 mm using a modulator and a photo-detector (PD) with a modest bandwidth of less than 1 GHz. The proposed interrogation system is intrinsically robust against environmental changes.

Fabricate Optical Microfiber by Using Flame Brushing Technique and Coated with Polymer Polyaniline for Sensing Application

NASA Astrophysics Data System (ADS)

Razak, N. A.; Hamida, B. A.; Irawati, N.; Habaebi, M. H.

2017-06-01

Adiabaticity is one of the essential criteria in producing good fabricated tapered fibers. Good tapered fibers can be use in sensor application such as humidity sensor, temperature sensor and refractive index sensor. In this paper, good tapering silica fiber is produced by using flame brushing technique and then, the microfiber is coated with polymer Polyaniline (PAni) to sense different type of alcohols with different concentrations. The outcome of this experiment gives excellent repeatability in the detection of alcohol sensing with a sensitivity of 0.1332 μW/% and a resolution of 3.764%. In conclusion, conducting polymer coated optical microfiber sensor for alcohol detection with low cost, effective and simple set-up was successfully achieved in this study.

Desensitized Optimal Filtering and Sensor Fusion Toolkit

NASA Technical Reports Server (NTRS)

Karlgaard, Christopher D.

2015-01-01

Analytical Mechanics Associates, Inc., has developed a software toolkit that filters and processes navigational data from multiple sensor sources. A key component of the toolkit is a trajectory optimization technique that reduces the sensitivity of Kalman filters with respect to model parameter uncertainties. The sensor fusion toolkit also integrates recent advances in adaptive Kalman and sigma-point filters for non-Gaussian problems with error statistics. This Phase II effort provides new filtering and sensor fusion techniques in a convenient package that can be used as a stand-alone application for ground support and/or onboard use. Its modular architecture enables ready integration with existing tools. A suite of sensor models and noise distribution as well as Monte Carlo analysis capability are included to enable statistical performance evaluations.

Advances in Bio-Tactile Sensors for Minimally Invasive Surgery Using the Fibre Bragg Grating Force Sensor Technique:A Survey

PubMed Central

Abushagur, Abdulfatah A.G.; Arsad, Norhana; Ibne Reaz, Mamun; Ashrif, A.; Bakar, A.

2014-01-01

The large interest in utilising fibre Bragg grating (FBG) strain sensors for minimally invasive surgery (MIS) applications to replace conventional electrical tactile sensors has grown in the past few years. FBG strain sensors offer the advantages of optical fibre sensors, such as high sensitivity, immunity to electromagnetic noise, electrical passivity and chemical inertness, but are not limited by phase discontinuity or intensity fluctuations. FBG sensors feature a wavelength-encoding sensing signal that enables distributed sensing that utilises fewer connections. In addition, their flexibility and lightness allow easy insertion into needles and catheters, thus enabling localised measurements inside tissues and blood. Two types of FBG tactile sensors have been emphasised in the literature: single-point and array FBG tactile sensors. This paper describes the current design, development and research of the optical fibre tactile techniques that are based on FBGs to enhance the performance of MIS procedures in general. Providing MIS or microsurgery surgeons with accurate and precise measurements and control of the contact forces during tissues manipulation will benefit both surgeons and patients. PMID:24721774

Improving the Ability of Image Sensors to Detect Faint Stars and Moving Objects Using Image Deconvolution Techniques

PubMed Central

Fors, Octavi; Núñez, Jorge; Otazu, Xavier; Prades, Albert; Cardinal, Robert D.

2010-01-01

In this paper we show how the techniques of image deconvolution can increase the ability of image sensors as, for example, CCD imagers, to detect faint stars or faint orbital objects (small satellites and space debris). In the case of faint stars, we show that this benefit is equivalent to double the quantum efficiency of the used image sensor or to increase the effective telescope aperture by more than 30% without decreasing the astrometric precision or introducing artificial bias. In the case of orbital objects, the deconvolution technique can double the signal-to-noise ratio of the image, which helps to discover and control dangerous objects as space debris or lost satellites. The benefits obtained using CCD detectors can be extrapolated to any kind of image sensors. PMID:22294896

Improving the ability of image sensors to detect faint stars and moving objects using image deconvolution techniques.

PubMed

Fors, Octavi; Núñez, Jorge; Otazu, Xavier; Prades, Albert; Cardinal, Robert D

2010-01-01

In this paper we show how the techniques of image deconvolution can increase the ability of image sensors as, for example, CCD imagers, to detect faint stars or faint orbital objects (small satellites and space debris). In the case of faint stars, we show that this benefit is equivalent to double the quantum efficiency of the used image sensor or to increase the effective telescope aperture by more than 30% without decreasing the astrometric precision or introducing artificial bias. In the case of orbital objects, the deconvolution technique can double the signal-to-noise ratio of the image, which helps to discover and control dangerous objects as space debris or lost satellites. The benefits obtained using CCD detectors can be extrapolated to any kind of image sensors.

A novel input-parasitic compensation technique for a nanopore-based CMOS DNA detection sensor

NASA Astrophysics Data System (ADS)

Kim, Jungsuk

2016-12-01

This paper presents a novel input-parasitic compensation (IPC) technique for a nanopore-based complementary metal-oxide-semiconductor (CMOS) DNA detection sensor. A resistive-feedback transimpedance amplifier is typically adopted as the headstage of a DNA detection sensor to amplify the minute ionic currents generated from a nanopore and convert them to a readable voltage range for digitization. But, parasitic capacitances arising from the headstage input and the nanopore often cause headstage saturation during nanopore sensing, thereby resulting in significant DNA data loss. To compensate for the unwanted saturation, in this work, we propose an area-efficient and automated IPC technique, customized for a low-noise DNA detection sensor, fabricated using a 0.35- μm CMOS process; we demonstrated this prototype in a benchtop test using an α-hemolysin ( α-HL) protein nanopore.

Advanced optical position sensors for magnetically suspended wind tunnel models

NASA Technical Reports Server (NTRS)

Lafleur, S.

1985-01-01

A major concern to aerodynamicists has been the corruption of wind tunnel test data by model support structures, such as stings or struts. A technique for magnetically suspending wind tunnel models was considered by Tournier and Laurenceau (1957) in order to overcome this problem. This technique is now implemented with the aid of a Large Magnetic Suspension and Balance System (LMSBS) and advanced position sensors for measuring model attitude and position within the test section. Two different optical position sensors are discussed, taking into account a device based on the use of linear CCD arrays, and a device utilizing area CID cameras. Current techniques in image processing have been employed to develop target tracking algorithms capable of subpixel resolution for the sensors. The algorithms are discussed in detail, and some preliminary test results are reported.

Incremental Support Vector Machine Framework for Visual Sensor Networks

NASA Astrophysics Data System (ADS)

Awad, Mariette; Jiang, Xianhua; Motai, Yuichi

2006-12-01

Motivated by the emerging requirements of surveillance networks, we present in this paper an incremental multiclassification support vector machine (SVM) technique as a new framework for action classification based on real-time multivideo collected by homogeneous sites. The technique is based on an adaptation of least square SVM (LS-SVM) formulation but extends beyond the static image-based learning of current SVM methodologies. In applying the technique, an initial supervised offline learning phase is followed by a visual behavior data acquisition and an online learning phase during which the cluster head performs an ensemble of model aggregations based on the sensor nodes inputs. The cluster head then selectively switches on designated sensor nodes for future incremental learning. Combining sensor data offers an improvement over single camera sensing especially when the latter has an occluded view of the target object. The optimization involved alleviates the burdens of power consumption and communication bandwidth requirements. The resulting misclassification error rate, the iterative error reduction rate of the proposed incremental learning, and the decision fusion technique prove its validity when applied to visual sensor networks. Furthermore, the enabled online learning allows an adaptive domain knowledge insertion and offers the advantage of reducing both the model training time and the information storage requirements of the overall system which makes it even more attractive for distributed sensor networks communication.

Volatile fatty acids as substrates for iron and sulfate reduction in Arctic marine sediments, Svalbard

NASA Astrophysics Data System (ADS)

Finke, N.; Vandieken, V.; Jorgensen, B. B.

2006-12-01

Anaerobic degradation of complex organic material in aquatic systems is a multi-step process. The metabolic products of fermentative bacteria serve as electron donors for the terminal oxidizing bacteria. In marine sediments, iron reduction and sulfate reduction are generally the most important terminal oxidation processes in the upper anoxic zone [1]. Microorganisms that reduce iron and sulfate may use a broad range of electron donors, yet the list of potential substrates provides little information about the substrates used in situ by these organisms. Investigations on the electron donors for sulfate reducers in marine sediments have shown that volatile fatty acids (VFA), and in particular acetate, together with hydrogen are the major substrates (e.g. [2-4]). Similar investigations for iron reduction or simultaneous iron and sulfate reduction are lacking for marine sediments. Furthermore, most of these studies were made in temperate sediments and little is known about the substrates for sulfate reducers in permanently cold sediments, which account for >90% of the ocean floor [5]. We investigated the relative contributions of iron reduction and sulfate reduction to the terminal oxidation of organic carbon and the importance of acetate, lactate, propionate, and isobutyrate as electron donors for iron and sulfate reduction in permanently cold, Arctic sediments from Svalbard. In the surface layer (0-2 cm) sulfate reduction accounted for 2/3 of the organic carbon oxidation (determined as DIC production), the remaining 1/3 were attributed to iron reduction. In the 5-9 cm layer sulfate reduction was the sole important terminal oxidation step. The contribution of acetate to terminal oxidation was determined by radiotracer incubation as well as from the accumulation after the inhibition of sulfate reduction by selenate. The rates determined with the two methods varied by less than 20%. Acetate turnover, determined with the tracer incubations, accounted for 10 and 40% of the sulfate reduction in the 0-2 cm and 5-9 cm layer, respectively. Together acetate, lactate, propionate and isobutyrate accounted for 21 and 52% of the sulfate reduction, in the 0-2 cm and 5-9 cm layer, respectively. Assigning all acetate and lactate turnover in the selenate inhibited samples, these two VFA account for less than 10 and 2%, respectively, of the iron reduction in the 0-2 cm layer. Thus, 67 and 48% of the terminal oxidation in the 0-2cm and 5-9 cm layer must be driven by electron donors other than the investigated VFA. The sulfate reduction rates as well as the VFA turnover rates were at the lower end of reported rates from similar studies, mostly measured in temperate sites (e.g. [2-4, 6, 7]). Comparing a series of studies with different in situ temperatures shows, parameters other than in situ temperature seem to be more important in determining the sulfate reduction and VFA turnover rates. [1] Thamdrup, B. (2000) Bacterial manganese and iron reduction in aquatic sediments, 41-84 pp. Kluwer Academic / Plenum Publ., New York. [2] Parkes, R.J., Gibson, G.R., Mueller-Harvey, I., Buckingham, W.J. and Herbert, R.A. (1989) J. Gen. Microbiol. 135, 175-187. [3] Christensen, D. (1984) Limnol. Oceanogr. 29, 189-192. [4] Shaw, D.G. and McIntosh, D.J. (1990) Estuarine Coastal & Shelf Science 31, 775-788. [5] Levitus, S. and Boyer, T. (1994) World Ocean Atlas, pp. US Department of Commerce, Washington, DC. [6] Kristensen, E., King, G.M., Holmer, M., Banta, G.T., Jensen, M.H., Hansen, K. and Bussarawit, N. (1994) Mar. Ecol.-Prog. Ser. 109, 245-255. [7] Wellsbury, P. and Parkes, R.J. (1995) FEMS Microbiol. Ecol. 17, 85-94.

Giant Magnetoresistance Sensors: A Review on Structures and Non-Destructive Eddy Current Testing Applications

PubMed Central

Rifai, Damhuji; Abdalla, Ahmed N.; Ali, Kharudin; Razali, Ramdan

2016-01-01

Non-destructive eddy current testing (ECT) is widely used to examine structural defects in ferromagnetic pipe in the oil and gas industry. Implementation of giant magnetoresistance (GMR) sensors as magnetic field sensors to detect the changes of magnetic field continuity have increased the sensitivity of eddy current techniques in detecting the material defect profile. However, not many researchers have described in detail the structure and issues of GMR sensors and their application in eddy current techniques for nondestructive testing. This paper will describe the implementation of GMR sensors in non-destructive testing eddy current testing. The first part of this paper will describe the structure and principles of GMR sensors. The second part outlines the principles and types of eddy current testing probe that have been studied and developed by previous researchers. The influence of various parameters on the GMR measurement and a factor affecting in eddy current testing will be described in detail in the third part of this paper. Finally, this paper will discuss the limitations of coil probe and compensation techniques that researchers have applied in eddy current testing probes. A comprehensive review of previous studies on the application of GMR sensors in non-destructive eddy current testing also be given at the end of this paper. PMID:26927123

Giant Magnetoresistance Sensors: A Review on Structures and Non-Destructive Eddy Current Testing Applications.

PubMed

Rifai, Damhuji; Abdalla, Ahmed N; Ali, Kharudin; Razali, Ramdan

2016-02-26

Non-destructive eddy current testing (ECT) is widely used to examine structural defects in ferromagnetic pipe in the oil and gas industry. Implementation of giant magnetoresistance (GMR) sensors as magnetic field sensors to detect the changes of magnetic field continuity have increased the sensitivity of eddy current techniques in detecting the material defect profile. However, not many researchers have described in detail the structure and issues of GMR sensors and their application in eddy current techniques for nondestructive testing. This paper will describe the implementation of GMR sensors in non-destructive testing eddy current testing. The first part of this paper will describe the structure and principles of GMR sensors. The second part outlines the principles and types of eddy current testing probe that have been studied and developed by previous researchers. The influence of various parameters on the GMR measurement and a factor affecting in eddy current testing will be described in detail in the third part of this paper. Finally, this paper will discuss the limitations of coil probe and compensation techniques that researchers have applied in eddy current testing probes. A comprehensive review of previous studies on the application of GMR sensors in non-destructive eddy current testing also be given at the end of this paper.

Wireless sensor platform

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Pooran C.; Killough, Stephen M.; Kuruganti, Phani Teja

A wireless sensor platform and methods of manufacture are provided. The platform involves providing a plurality of wireless sensors, where each of the sensors is fabricated on flexible substrates using printing techniques and low temperature curing. Each of the sensors can include planar sensor elements and planar antennas defined using the printing and curing. Further, each of the sensors can include a communications system configured to encode the data from the sensors into a spread spectrum code sequence that is transmitted to a central computer(s) for use in monitoring an area associated with the sensors.

Nearest neighbor imputation using spatial–temporal correlations in wireless sensor networks

PubMed Central

Li, YuanYuan; Parker, Lynne E.

2016-01-01

Missing data is common in Wireless Sensor Networks (WSNs), especially with multi-hop communications. There are many reasons for this phenomenon, such as unstable wireless communications, synchronization issues, and unreliable sensors. Unfortunately, missing data creates a number of problems for WSNs. First, since most sensor nodes in the network are battery-powered, it is too expensive to have the nodes retransmit missing data across the network. Data re-transmission may also cause time delays when detecting abnormal changes in an environment. Furthermore, localized reasoning techniques on sensor nodes (such as machine learning algorithms to classify states of the environment) are generally not robust enough to handle missing data. Since sensor data collected by a WSN is generally correlated in time and space, we illustrate how replacing missing sensor values with spatially and temporally correlated sensor values can significantly improve the network’s performance. However, our studies show that it is important to determine which nodes are spatially and temporally correlated with each other. Simple techniques based on Euclidean distance are not sufficient for complex environmental deployments. Thus, we have developed a novel Nearest Neighbor (NN) imputation method that estimates missing data in WSNs by learning spatial and temporal correlations between sensor nodes. To improve the search time, we utilize a kd-tree data structure, which is a non-parametric, data-driven binary search tree. Instead of using traditional mean and variance of each dimension for kd-tree construction, and Euclidean distance for kd-tree search, we use weighted variances and weighted Euclidean distances based on measured percentages of missing data. We have evaluated this approach through experiments on sensor data from a volcano dataset collected by a network of Crossbow motes, as well as experiments using sensor data from a highway traffic monitoring application. Our experimental results show that our proposed 𝒦-NN imputation method has a competitive accuracy with state-of-the-art Expectation–Maximization (EM) techniques, while using much simpler computational techniques, thus making it suitable for use in resource-constrained WSNs. PMID:28435414

Effects of a 3 strain -based direct-fed microbial and dietary fiber concentration on growth performance and expression of genes related to absorption and metabolism of volatile fatty acids in weanling pigs.

PubMed

Jaworski, N W; Owusu-Asiedu, A; Walsh, M C; McCann, J C; Loor, J J; Stein, H H

2017-01-01

Effects of a -based direct-fed microbial (DFM) on growth performance, plasma tumor necrosis factor ɑ (TNFɑ), relative gene expression, and intestinal VFA concentrations in weanling pigs fed low- or high-fiber diets were evaluated. Two hundred pigs (initial BW: 6.31 ± 0.73 kg) were allotted to 1 of 4 dietary treatments (5 pigs per pen and 10 pens per treatment). Treatments were arranged in a 2 × 2 factorial design with 2 diet types [low-fiber (LF) or high-fiber (HF)] and 2 concentrations of DFM (0 or 60 g DFM/t of feed). The DFM contained 1.5 × 10 cfu/g and was obtained from Danisco Animal Nutrition-DuPont Industrial Biosciences, Marlborough, UK. Phase 1 diets were fed for 2 wk post-weaning and phase 2 diets were fed over the following 29 d. Low fiber diets contained corn and soybean meal as main ingredients and HF diets contained corn, soybean meal, corn distillers dried grains with solubles (7.5 and 15.0% in phase 1 and 2, respectively), and wheat middlings (10.0%). Pigs and feed were weighed at the start and at the end of each phase, and ADG, ADFI, and G:F were calculated. At the conclusion of phase 2, blood was collected from 1 pig per pen and 1 pig per pen was sacrificed. Cecum and rectum contents were analyzed for VFA, and tissue samples were collected from the ileum, cecum, rectum, and liver to determine expression of genes related to absorption and metabolism of VFA using quantitative reverse transcription-PCR. Results indicated that feeding HF diets reduced ( ≤ 0.05) ADFI and ADG of pigs compared with feeding LF diets. Pigs fed DFM diets had improved ( ≤ 0.05) G:F compared with pigs fed non-DFM diets. Pigs fed LF diets had greater ( ≤ 0.05) BW at the end of phase 2 compared with pigs fed HF diets. The concentration of VFA in rectum contents was greater ( ≤ 0.05) in pigs fed LF diets than in pigs fed HF diets. The expression of in the rectum of pigs fed HF diets was greater ( ≤ 0.05) than for pigs fed LF diets, and pigs fed DFM-containing diets had an increased ( ≤ 0.05) expression of in the liver. Pigs fed HF diets had greater ( ≤ 0.05) concentrations of urea N in plasma compared with pigs fed LF diets, but dietary fiber and DFM had no effect on plasma concentration of TNF-ɑ. In conclusion, the -based DFM improved overall G:F of weanling pigs, but pigs fed LF diets had greater final BW than pigs fed HF diets.

Effect of monensin inclusion on intake, digestion, and ruminal fermentation parameters by Bos taurus indicus and Bos taurus taurus steers consuming bermudagrass hay.

PubMed

Bell, N L; Anderson, R C; Callaway, T R; Franco, M O; Sawyer, J E; Wickersham, T A

2017-06-01

Effects of monensin inclusion and cattle subspecies on utilization of bermudagrass hay (13.7% CP, 77.3% NDF, and 38.8% ADF) were evaluated using ruminally cannulated steers (5 [BI] and 5 [BT]; 398 kg BW). Subspecies were concurrently subjected to a 2-period, 2-treatment crossover design. Treatments were 0 (CON) or 200 mg·steer·d monensin (MON) in 0.91 kg dried distillers' grains with solubles. Periods were 70 d in length: 20 d of adaptation, 22 d of sample collection, and 28 d for withdrawal of treatment. Steers were group housed during adaptation and moved to individual covered pens for sampling. Hay, ort, and fecal grab samples were collected d 21 through 25 for determination of intake and digestion. Ruminal fluid was collected with a suction strainer 0, 2, 4, 8, and 12 h after feeding on d 42 for pH, VFA, and ruminal NH-N (RAN) analysis. Additionally, at h 2, ruminal fluid and contents were collected for determination of rate of NH production and CH production rate. No subspecies × monensin interactions were observed ( ≥ 0.12). Monensin had no effect ( ≥ 0.16) on intake or digestibility parameters. No subspecies effect ( ≥ 0.11) was observed for forage OM intake, total OM intake, or OM digestion. Total digestible OM intake tended to be greater ( = 0.06) for BT steers than for BI steers (14.0 vs. 12.2 g/kg BW). There was an effect of hour after feeding ( ≤ 0.01) on pH, total VFA, acetate:propionate ratio, and molar percent acetate and propionate. Total VFA concentration was greater ( = 0.01) in CON steers than in MON steers (66.5 vs. 62.0 m). Monensin decreased molar percent acetate ( = 0.02) from 72.5 to 71.2% and increased molar percent propionate ( < 0.01) from 16.9 to 18.7%, resulting in a reduced ( < 0.01) acetate:propionate ratio (from 4.34 to 3.85). Although not significantly ( = 0.19), monensin numerically reduced the CH production rate by 15.8%. Greater ( = 0.07) CH production rate tended to be observed in BI steers than in BT steers (21.4 vs. 16.6 μmol CH·mL·h, respectively). Monensin had no effect ( ≥ 0.32) on pH, RAN, or rate of NH production. A subspecies × hour after feeding interaction was observed for RAN, with BT having greater RAN at h 0 and 4, whereas BI had greater RAN at h 2, 8, and 12. Overall, monensin decreased the acetate:propionate ratio and total VFA concentration but had no effect on forage utilization. steers consumed less digestible OM and had a greater CH production rate compared with BT steers, suggesting BT were better able to utilize the available forage resource than BI.

Ergot alkaloids from endophyte-infected tall fescue decrease reticuloruminal epithelial blood flow and volatile fatty acid absorption from the washed reticulorumen.

PubMed

Foote, A P; Kristensen, N B; Klotz, J L; Kim, D H; Koontz, A F; McLeod, K R; Bush, L P; Schrick, F N; Harmon, D L

2013-11-01

An experiment was conducted to determine if ergot alkaloids affect blood flow to the absorptive surface of the rumen. Steers (n=8) were pair-fed alfalfa cubes and received ground endophyte-infected (Neotyphodium coenophialum) tall fescue (Lolium arundinaceum; E+) seed (0.015 mg ergovaline·kg BW(-1)·d(-1)) or endophyte-free tall fescue (E-) seed via the rumen cannula 2x daily for 7 d at thermoneutral (TN; 22°C) and heat stress (HS; 32°C) conditions. On d 8, the rumen was emptied and rinsed. A buffer containing VFA was incubated in the following sequence: control (CON), 15 μg ergovaline·kg BW(-1) (1×EXT) from a tall fescue seed extract, and 45 μg ergovaline·kg BW(-1) (3×EXT). For each buffer treatment there were two 30-min incubations: a 30-min incubation of a treatment buffer with no sampling followed by an incubation of an identical sampling buffer with the addition of Cr-EDTA and deuterium oxide (D2O). Epithelial blood flow was calculated as ruminal clearance of D2O corrected for influx of physiological water and liquid outflow. Feed intake decreased with dosing E+ seed at HS but not at thermoneutral conditions (TN; P<0.02). Dosing E+ seed decreased serum prolactin (P<0.005) at TN. At HS, prolactin decreased in both groups over the 8-d experiment (P<0.0001), but there was no difference in E+ and E- steers (P=0.33). There was a seed treatment×buffer treatment interaction at TN (P=0.038), indicating that E+ seed treatment decreased reticuloruminal epithelial blood flow at TN during the CON incubation, but the two groups of steers were not different during 1×EXT and 3×EXT (P>0.05). Inclusion of the extract in the buffer caused at least a 50% reduction in epithelial blood flow at TN (P=0.004), but there was no difference between 1×EXT and 3×EXT. There was a seed × buffer treatment interaction at HS (P=0.005), indicating that the reduction of blood flow induced by incubating the extract was larger for steers receiving E- seed than E+ seed. Volatile fatty acid flux was reduced during the 1×EXT and 3×EXT treatments (P<0.01). An additional experiment was conducted to determine the effect of time on blood flow and VFA flux because buffer sequence could not be randomized. Time either increased (P=0.05) or did not affect blood flow (P=0.18) or VFA flux (P>0.80), indicating that observed differences are due to the presence of ergot alkaloids in the rumen. A decrease in VFA absorption could contribute to the signs of fescue toxicosis including depressed growth and performance.

An Autonomous Sensor System Architecture for Active Flow and Noise Control Feedback

NASA Technical Reports Server (NTRS)

Humphreys, William M, Jr.; Culliton, William G.

2008-01-01

Multi-channel sensor fusion represents a powerful technique to simply and efficiently extract information from complex phenomena. While the technique has traditionally been used for military target tracking and situational awareness, a study has been successfully completed that demonstrates that sensor fusion can be applied equally well to aerodynamic applications. A prototype autonomous hardware processor was successfully designed and used to detect in real-time the two-dimensional flow reattachment location generated by a simple separated-flow wind tunnel model. The success of this demonstration illustrates the feasibility of using autonomous sensor processing architectures to enhance flow control feedback signal generation.

Optimal sensor locations for the backward Lagrangian stochastic technique in measuring lagoon gas emission

USDA-ARS?s Scientific Manuscript database

This study evaluated the impact of gas concentration and wind sensor locations on the accuracy of the backward Lagrangian stochastic inverse-dispersion technique (bLS) for measuring gas emission rates from a typical lagoon environment. Path-integrated concentrations (PICs) and 3-dimensional (3D) wi...

Biology Inspired Approach for Communal Behavior in Sensor Networks

NASA Technical Reports Server (NTRS)

Jones, Kennie H.; Lodding, Kenneth N.; Olariu, Stephan; Wilson, Larry; Xin, Chunsheng

2006-01-01

Research in wireless sensor network technology has exploded in the last decade. Promises of complex and ubiquitous control of the physical environment by these networks open avenues for new kinds of science and business. Due to the small size and low cost of sensor devices, visionaries promise systems enabled by deployment of massive numbers of sensors working in concert. Although the reduction in size has been phenomenal it results in severe limitations on the computing, communicating, and power capabilities of these devices. Under these constraints, research efforts have concentrated on developing techniques for performing relatively simple tasks with minimal energy expense assuming some form of centralized control. Unfortunately, centralized control does not scale to massive size networks and execution of simple tasks in sparsely populated networks will not lead to the sophisticated applications predicted. These must be enabled by new techniques dependent on local and autonomous cooperation between sensors to effect global functions. As a step in that direction, in this work we detail a technique whereby a large population of sensors can attain a global goal using only local information and by making only local decisions without any form of centralized control.

Real time interrogation technique for fiber Bragg grating enhanced fiber loop ringdown sensors array.

PubMed

Zhang, Yunlong; Li, Ruoming; Shi, Yuechun; Zhang, Jintao; Chen, Xiangfei; Liu, Shengchun

2015-06-01

A novel fiber Bragg grating aided fiber loop ringdown (FLRD) sensor array and the wavelength-time multiplexing based interrogation technique for the FLRD sensors array are proposed. The interrogation frequency of the system is formulated and the interrelationships among the parameters of the system are analyzed. To validate the performance of the proposed system, a five elements array is experimentally demonstrated, and the system shows the capability of real time monitoring every FLRD element with interrogation frequency of 125.5 Hz.

Probe beam deflection technique as acoustic emission directionality sensor with photoacoustic emission source.

PubMed

Barnes, Ronald A; Maswadi, Saher; Glickman, Randolph; Shadaram, Mehdi

2014-01-20

The goal of this paper is to demonstrate the unique capability of measuring the vector or angular information of propagating acoustic waves using an optical sensor. Acoustic waves were generated using photoacoustic interaction and detected by the probe beam deflection technique. Experiments and simulations were performed to study the interaction of acoustic emissions with an optical sensor in a coupling medium. The simulated results predict the probe beam and wavefront interaction and produced simulated signals that are verified by experiment.

Monitoring cure of composite resins using frequency dependent electromagnetic sensing techniques

NASA Technical Reports Server (NTRS)

Kranbuehl, D. E.; Hoff, M. S.; Loos, A. C.; Freeman, W. T., Jr.; Eichinger, D. A.

1988-01-01

A nondestructive in situ measurement technique has been developed for monitoring and measuring the cure processing properties of composite resins. Frequency dependent electromagnetic sensors (FDEMS) were used to directly measure resin viscosity during cure. The effects of the cure cycle and resin aging on the viscosity during cure were investigated using the sensor. Viscosity measurements obtained using the sensor are compared with the viscosities calculated by the Loos-Springer cure process model. Good overall agreement was obtained except for the aged resin samples.

Bragg gratings: Optical microchip sensors

NASA Astrophysics Data System (ADS)

Watts, Sam

2010-07-01

A direct UV writing technique that can create multiple Bragg gratings and waveguides in a planar silica-on-silicon chip is enabling sensing applications ranging from individual disposable sensors for biotechnology through to multiplexed sensor networks in pharmaceutical manufacturing.

Fabrication and Characterization of a Micro Methanol Sensor Using the CMOS-MEMS Technique.

PubMed

Fong, Chien-Fu; Dai, Ching-Liang; Wu, Chyan-Chyi

2015-10-23

A methanol microsensor integrated with a micro heater manufactured using the complementary metal oxide semiconductor (CMOS)-microelectromechanical system (MEMS) technique was presented. The sensor has a capability of detecting low concentration methanol gas. Structure of the sensor is composed of interdigitated electrodes, a sensitive film and a heater. The heater located under the interdigitated electrodes is utilized to provide a working temperature to the sensitive film. The sensitive film prepared by the sol-gel method is tin dioxide doped cadmium sulfide, which is deposited on the interdigitated electrodes. To obtain the suspended structure and deposit the sensitive film, the sensor needs a post-CMOS process to etch the sacrificial silicon dioxide layer and silicon substrate. The methanol senor is a resistive type. A readout circuit converts the resistance variation of the sensor into the output voltage. The experimental results show that the methanol sensor has a sensitivity of 0.18 V/ppm.

Fabrication and Characterization of a Micro Methanol Sensor Using the CMOS-MEMS Technique

PubMed Central

Fong, Chien-Fu; Dai, Ching-Liang; Wu, Chyan-Chyi

2015-01-01

A methanol microsensor integrated with a micro heater manufactured using the complementary metal oxide semiconductor (CMOS)-microelectromechanical system (MEMS) technique was presented. The sensor has a capability of detecting low concentration methanol gas. Structure of the sensor is composed of interdigitated electrodes, a sensitive film and a heater. The heater located under the interdigitated electrodes is utilized to provide a working temperature to the sensitive film. The sensitive film prepared by the sol-gel method is tin dioxide doped cadmium sulfide, which is deposited on the interdigitated electrodes. To obtain the suspended structure and deposit the sensitive film, the sensor needs a post-CMOS process to etch the sacrificial silicon dioxide layer and silicon substrate. The methanol senor is a resistive type. A readout circuit converts the resistance variation of the sensor into the output voltage. The experimental results show that the methanol sensor has a sensitivity of 0.18 V/ppm. PMID:26512671

Heart rate estimation from FBG sensors using cepstrum analysis and sensor fusion.

PubMed

Zhu, Yongwei; Fook, Victor Foo Siang; Jianzhong, Emily Hao; Maniyeri, Jayachandran; Guan, Cuntai; Zhang, Haihong; Jiliang, Eugene Phua; Biswas, Jit

2014-01-01

This paper presents a method of estimating heart rate from arrays of fiber Bragg grating (FBG) sensors embedded in a mat. A cepstral domain signal analysis technique is proposed to characterize Ballistocardiogram (BCG) signals. With this technique, the average heart beat intervals can be estimated by detecting the dominant peaks in the cepstrum, and the signals of multiple sensors can be fused together to obtain higher signal to noise ratio than each individual sensor. Experiments were conducted with 10 human subjects lying on 2 different postures on a bed. The estimated heart rate from BCG was compared with heart rate ground truth from ECG, and the mean error of estimation obtained is below 1 beat per minute (BPM). The results show that the proposed fusion method can achieve promising heart rate measurement accuracy and robustness against various sensor contact conditions.

Enhanced Strain Measurement Range of an FBG Sensor Embedded in Seven-Wire Steel Strands

PubMed Central

Kim, Jae-Min; Kim, Chul-Min; Choi, Song-Yi

2017-01-01

FBG sensors offer many advantages, such as a lack of sensitivity to electromagnetic waves, small size, high durability, and high sensitivity. However, their maximum strain measurement range is lower than the yield strain range (about 1.0%) of steel strands when embedded in steel strands. This study proposes a new FBG sensing technique in which an FBG sensor is recoated with polyimide and protected by a polyimide tube in an effort to enhance the maximum strain measurement range of FBG sensors embedded in strands. The validation test results showed that the proposed FBG sensing technique has a maximum strain measurement range of 1.73% on average, which is 1.73 times higher than the yield strain of the strands. It was confirmed that recoating the FBG sensor with polyimide and protecting the FBG sensor using a polyimide tube could effectively enhance the maximum strain measurement range of FBG sensors embedded in strands. PMID:28718826

Wearable sensor systems for infants.

PubMed

Zhu, Zhihua; Liu, Tao; Li, Guangyi; Li, Tong; Inoue, Yoshio

2015-02-05

Continuous health status monitoring of infants is achieved with the development and fusion of wearable sensing technologies, wireless communication techniques and a low energy-consumption microprocessor with high performance data processing algorithms. As a clinical tool applied in the constant monitoring of physiological parameters of infants, wearable sensor systems for infants are able to transmit the information obtained inside an infant's body to clinicians or parents. Moreover, such systems with integrated sensors can perceive external threats such as falling or drowning and warn parents immediately. Firstly, the paper reviews some available wearable sensor systems for infants; secondly, we introduce the different modules of the framework in the sensor systems; lastly, the methods and techniques applied in the wearable sensor systems are summarized and discussed. The latest research and achievements have been highlighted in this paper and the meaningful applications in healthcare and behavior analysis are also presented. Moreover, we give a lucid perspective of the development of wearable sensor systems for infants in the future.

Investigation of substrate-mounted thin-film meteoroid sensors for use in large area impact experiments

NASA Technical Reports Server (NTRS)

Carollo, S. F.; Davis, J. M.; Dance, W. E.

1973-01-01

Two types of sensor designs were investigated: (1)a polysulfone dielectric film with vapor-deposited aluminum and gold sensor plates, bonded to a relatively thick aluminum substrate, and (2) an aluminum oxide (A1203) dielectric layer prepared on an aluminum substrate by anodization, with a layer of vapor-deposited aluminum providing one sensor plate and the substrate serving as the other plate. In the first design, specimens were prepared which indicate the state of the art for application of this type of sensor for elements of a meteoroid detection system having an area as large as 10 sq M. Techniques were investigated for casting large-area polysulfone films on the surface of water and for transferring the films from the water. Methods of preparing sensors by layering of films, the deposition of capacitor plates, and sensor film-to-substrate bonding, as well as techniques for making electrical connections to the capacitor plates, were studied.

Wearable Sensor Systems for Infants

PubMed Central

Zhu, Zhihua; Liu, Tao; Li, Guangyi; Li, Tong; Inoue, Yoshio

2015-01-01

Continuous health status monitoring of infants is achieved with the development and fusion of wearable sensing technologies, wireless communication techniques and a low energy-consumption microprocessor with high performance data processing algorithms. As a clinical tool applied in the constant monitoring of physiological parameters of infants, wearable sensor systems for infants are able to transmit the information obtained inside an infant's body to clinicians or parents. Moreover, such systems with integrated sensors can perceive external threats such as falling or drowning and warn parents immediately. Firstly, the paper reviews some available wearable sensor systems for infants; secondly, we introduce the different modules of the framework in the sensor systems; lastly, the methods and techniques applied in the wearable sensor systems are summarized and discussed. The latest research and achievements have been highlighted in this paper and the meaningful applications in healthcare and behavior analysis are also presented. Moreover, we give a lucid perspective of the development of wearable sensor systems for infants in the future. PMID:25664432

Novel techniques for optical sensor using single core multi-layer structures for electric field detection

NASA Astrophysics Data System (ADS)

Ali, Amir R.; Kamel, Mohamed A.

2017-05-01

This paper studies the effect of the electrostriction force on the single optical dielectric core coated with multi-layers based on whispering gallery mode (WGM). The sensing element is a dielectric core made of polymeric material coated with multi-layers having different dielectric and mechanical properties. The external electric field deforming the sensing element causing shifts in its WGM spectrum. The multi-layer structures will enhance the body and the pressure forces acting on the core of the sensing element. Due to the gradient on the dielectric permittivity; pressure forces at the interface between every two layers will be created. Also, the gradient on Young's modulus will affect the overall stiffness of the optical sensor. In turn the sensitivity of the optical sensor to the electric field will be increased when the materials of each layer selected properly. A mathematical model is used to test the effect for that multi-layer structures. Two layering techniques are considered to increase the sensor's sensitivity; (i) Pressure force enhancement technique; and (ii) Young's modulus reduction technique. In the first technique, Young's modulus is kept constant for all layers, while the dielectric permittivity is varying. In this technique the results will be affected by the value dielectric permittivity of the outer medium surrounding the cavity. If the medium's dielectric permittivity is greater than that of the cavity, then the ascending ordered layers of the cavity will yield the highest sensitivity (the core will have the smallest dielectric permittivity) to the applied electric field and vice versa. In the second technique, Young's modulus is varying along the layers, while the dielectric permittivity has a certain constant value per layer. On the other hand, the descending order will enhance the sensitivity in the second technique. Overall, results show the multi-layer cavity based on these techniques will enhance the sensitivity compared to the typical polymeric optical sensor.

Novel Hybrid Scheduling Technique for Sensor Nodes with Mixed Criticality Tasks.

PubMed

Micea, Mihai-Victor; Stangaciu, Cristina-Sorina; Stangaciu, Valentin; Curiac, Daniel-Ioan

2017-06-26

Sensor networks become increasingly a key technology for complex control applications. Their potential use in safety- and time-critical domains has raised the need for task scheduling mechanisms specially adapted to sensor node specific requirements, often materialized in predictable jitter-less execution of tasks characterized by different criticality levels. This paper offers an efficient scheduling solution, named Hybrid Hard Real-Time Scheduling (H²RTS), which combines a static, clock driven method with a dynamic, event driven scheduling technique, in order to provide high execution predictability, while keeping a high node Central Processing Unit (CPU) utilization factor. From the detailed, integrated schedulability analysis of the H²RTS, a set of sufficiency tests are introduced and demonstrated based on the processor demand and linear upper bound metrics. The performance and correct behavior of the proposed hybrid scheduling technique have been extensively evaluated and validated both on a simulator and on a sensor mote equipped with ARM7 microcontroller.

A GENERIC PACKAGING TECHNIQUE USING FLUIDIC ISOLATION FOR LOW-DRIFT IMPLANTABLE PRESSURE SENSORS.

PubMed

Kim, A; Powell, C R; Ziaie, B

2015-06-01

This paper reports on a generic packaging method for reducing drift in implantable pressure sensors. The described technique uses fluidic isolation by encasing the pressure sensor in a liquid-filled medical-grade polyurethane balloon; thus, isolating it from surrounding aqueous environment that is the major source of baseline drift. In-vitro tests using commercial micromachined piezoresistive pressure sensors show an average baseline drift of 0.006 cmH 2 O/day (0.13 mmHg/month) for over 100 days of saline soak test, as compared to 0.101 cmH 2 O/day (2.23 mmHg/month) for a non-fluidic-isolated one soaked for 18 days. To our knowledge, this is the lowest reported drift for an implantable pressure sensor.

Planar Zeolite Film-Based Potentiometric Gas Sensors Manufactured by a Combined Thick-Film and Electroplating Technique

PubMed Central

Marr, Isabella; Reiß, Sebastian; Hagen, Gunter; Moos, Ralf

2011-01-01

Zeolites are promising materials in the field of gas sensors. In this technology-oriented paper, a planar setup for potentiometric hydrocarbon and hydrogen gas sensors using zeolites as ionic sodium conductors is presented, in which the Pt-loaded Na-ZSM-5 zeolite is applied using a thick-film technique between two interdigitated gold electrodes and one of them is selectively covered for the first time by an electroplated chromium oxide film. The influence of the sensor temperature, the type of hydrocarbons, the zeolite film thickness, and the chromium oxide film thickness is investigated. The influence of the zeolite on the sensor response is briefly discussed in the light of studies dealing with zeolites as selectivity-enhancing cover layers. PMID:22164042

An Analysis on Sensor Locations of the Human Body for Wearable Fall Detection Devices: Principles and Practice

PubMed Central

Özdemir, Ahmet Turan

2016-01-01

Wearable devices for fall detection have received attention in academia and industry, because falls are very dangerous, especially for elderly people, and if immediate aid is not provided, it may result in death. However, some predictive devices are not easily worn by elderly people. In this work, a huge dataset, including 2520 tests, is employed to determine the best sensor placement location on the body and to reduce the number of sensor nodes for device ergonomics. During the tests, the volunteer’s movements are recorded with six groups of sensors each with a triaxial (accelerometer, gyroscope and magnetometer) sensor, which is placed tightly on different parts of the body with special straps: head, chest, waist, right-wrist, right-thigh and right-ankle. The accuracy of individual sensor groups with their location is investigated with six machine learning techniques, namely the k-nearest neighbor (k-NN) classifier, Bayesian decision making (BDM), support vector machines (SVM), least squares method (LSM), dynamic time warping (DTW) and artificial neural networks (ANNs). Each technique is applied to single, double, triple, quadruple, quintuple and sextuple sensor configurations. These configurations create 63 different combinations, and for six machine learning techniques, a total of 63 × 6 = 378 combinations is investigated. As a result, the waist region is found to be the most suitable location for sensor placement on the body with 99.96% fall detection sensitivity by using the k-NN classifier, whereas the best sensitivity achieved by the wrist sensor is 97.37%, despite this location being highly preferred for today’s wearable applications. PMID:27463719

An Analysis on Sensor Locations of the Human Body for Wearable Fall Detection Devices: Principles and Practice.

PubMed

Özdemir, Ahmet Turan

2016-07-25

Wearable devices for fall detection have received attention in academia and industry, because falls are very dangerous, especially for elderly people, and if immediate aid is not provided, it may result in death. However, some predictive devices are not easily worn by elderly people. In this work, a huge dataset, including 2520 tests, is employed to determine the best sensor placement location on the body and to reduce the number of sensor nodes for device ergonomics. During the tests, the volunteer's movements are recorded with six groups of sensors each with a triaxial (accelerometer, gyroscope and magnetometer) sensor, which is placed tightly on different parts of the body with special straps: head, chest, waist, right-wrist, right-thigh and right-ankle. The accuracy of individual sensor groups with their location is investigated with six machine learning techniques, namely the k-nearest neighbor (k-NN) classifier, Bayesian decision making (BDM), support vector machines (SVM), least squares method (LSM), dynamic time warping (DTW) and artificial neural networks (ANNs). Each technique is applied to single, double, triple, quadruple, quintuple and sextuple sensor configurations. These configurations create 63 different combinations, and for six machine learning techniques, a total of 63 × 6 = 378 combinations is investigated. As a result, the waist region is found to be the most suitable location for sensor placement on the body with 99.96% fall detection sensitivity by using the k-NN classifier, whereas the best sensitivity achieved by the wrist sensor is 97.37%, despite this location being highly preferred for today's wearable applications.

Smart sensor systems for human health breath monitoring applications.

PubMed

Hunter, G W; Xu, J C; Biaggi-Labiosa, A M; Laskowski, D; Dutta, P K; Mondal, S P; Ward, B J; Makel, D B; Liu, C C; Chang, C W; Dweik, R A

2011-09-01

Breath analysis techniques offer a potential revolution in health care diagnostics, especially if these techniques can be brought into standard use in the clinic and at home. The advent of microsensors combined with smart sensor system technology enables a new generation of sensor systems with significantly enhanced capabilities and minimal size, weight and power consumption. This paper discusses the microsensor/smart sensor system approach and provides a summary of efforts to migrate this technology into human health breath monitoring applications. First, the basic capability of this approach to measure exhaled breath associated with exercise physiology is demonstrated. Building from this foundation, the development of a system for a portable asthma home health care system is described. A solid-state nitric oxide (NO) sensor for asthma monitoring has been identified, and efforts are underway to miniaturize this NO sensor technology and integrate it into a smart sensor system. It is concluded that base platform microsensor technology combined with smart sensor systems can address the needs of a range of breath monitoring applications and enable new capabilities for healthcare.

Scanning Mode Sensor for Detection of Flow Inhomogeneities

NASA Technical Reports Server (NTRS)

Adamovsky, Grigory (Inventor)

1998-01-01

A scanning mode sensor and method is provided for detection of flow inhomogeneities such as shock. The field of use of this invention is ground test control and engine control during supersonic flight. Prior art measuring techniques include interferometry. Schlieren, and shadowgraph techniques. These techniques. however, have problems with light dissipation. The present method and sensor utilizes a pencil beam of energy which is passed through a transparent aperture in a flow inlet in a time-sequential manner so as to alter the energy beam. The altered beam or its effects are processed and can be studied to reveal information about flow through the inlet which can in turn be used for engine control.

Scanning Mode Sensor for Detection of Flow Inhomogeneities

NASA Technical Reports Server (NTRS)

Adamovsky, Grigory (Inventor)

1996-01-01

A scanning mode sensor and method is provided for detection of flow inhomogeneities such as shock. The field of use of this invention is ground test control and engine control during supersonic flight. Prior art measuring techniques include interferometry, Schlieren, and shadowgraph techniques. These techniques, however, have problems with light dissipation. The present method and sensor utilizes a pencil beam of energy which is passed through a transparent aperture in a flow inlet in a time-sequential manner so as to alter the energy beam. The altered beam or its effects are processed and can be studied to reveal information about flow through the inlet which can in turn be used for engine control.

Rapid Parametric Mapping of the Longitudinal Relaxation Time T1 Using Two-Dimensional Variable Flip Angle Magnetic Resonance Imaging at 1.5 Tesla, 3 Tesla, and 7 Tesla

PubMed Central

Dieringer, Matthias A.; Deimling, Michael; Santoro, Davide; Wuerfel, Jens; Madai, Vince I.; Sobesky, Jan; von Knobelsdorff-Brenkenhoff, Florian; Schulz-Menger, Jeanette; Niendorf, Thoralf

2014-01-01

Introduction Visual but subjective reading of longitudinal relaxation time (T1) weighted magnetic resonance images is commonly used for the detection of brain pathologies. For this non-quantitative measure, diagnostic quality depends on hardware configuration, imaging parameters, radio frequency transmission field (B1+) uniformity, as well as observer experience. Parametric quantification of the tissue T1 relaxation parameter offsets the propensity for these effects, but is typically time consuming. For this reason, this study examines the feasibility of rapid 2D T1 quantification using a variable flip angles (VFA) approach at magnetic field strengths of 1.5 Tesla, 3 Tesla, and 7 Tesla. These efforts include validation in phantom experiments and application for brain T1 mapping. Methods T1 quantification included simulations of the Bloch equations to correct for slice profile imperfections, and a correction for B1+. Fast gradient echo acquisitions were conducted using three adjusted flip angles for the proposed T1 quantification approach that was benchmarked against slice profile uncorrected 2D VFA and an inversion-recovery spin-echo based reference method. Brain T1 mapping was performed in six healthy subjects, one multiple sclerosis patient, and one stroke patient. Results Phantom experiments showed a mean T1 estimation error of (-63±1.5)% for slice profile uncorrected 2D VFA and (0.2±1.4)% for the proposed approach compared to the reference method. Scan time for single slice T1 mapping including B1+ mapping could be reduced to 5 seconds using an in-plane resolution of (2×2) mm2, which equals a scan time reduction of more than 99% compared to the reference method. Conclusion Our results demonstrate that rapid 2D T1 quantification using a variable flip angle approach is feasible at 1.5T/3T/7T. It represents a valuable alternative for rapid T1 mapping due to the gain in speed versus conventional approaches. This progress may serve to enhance the capabilities of parametric MR based lesion detection and brain tissue characterization. PMID:24621588

Supersaturation of Dissolved Hydrogen and Methane in Rumen of Tibetan Sheep

PubMed Central

Wang, Min; Ungerfeld, Emilio M.; Wang, Rong; Zhou, Chuan She; Basang, Zhu Zha; Ao, Si Man; Tan, Zhi Liang

2016-01-01

Hydrogen (H2) is an essential substrate for methanogens to produce methane (CH4), and also influences pathways of volatile fatty acids (VFA) production in the rumen. Dissolved H2 (H2 (aq)) is the form of H2 available to microbes, and dissolved CH4 (CH4 (aq)) is important for indicating methanogens activity. Rumen H2 (aq) concentration has been estimated by assuming equilibrium with headspace gaseous H2 (H2 (g)) concentration using Henry's law, and has also been directly measured in the liquid phase in some in vitro and in vivo experiments. In this in vivo study, H2 (aq) and CH4 (aq) concentration measured directly in rumen fluid and their corresponding concentrations estimated from their gaseous phase concentrations, were compared to investigate the existence of equilibrium between the gas and liquid phases. Twenty-four Tibetan sheep were randomly assigned to two mixed diets containing the same concentrate mixed with oat grass (OG diet) or barley straw (BS diet). Rumen gaseous phase and contents were sampled using rumenocentesis and oral stomach tubing, respectively. Rumen H2 (aq) and CH4 (aq) concentration and VFA profile differed between sheep fed OG and BS diets. Measured H2 (aq) and CH4 (aq) concentration were greater than H2 (aq) and CH4 (aq) concentrations estimated using gas concentrations, indicating lack of equilibrium between gas and liquid phase and supersaturation of H2 and CH4 in rumen fluid. As a consequence, Gibbs energy changes (ΔG) estimated for various metabolic pathways were different when calculated using dissolved gases concentrations directly measured and when using dissolved gases concentrations assuming equilibrium with the gaseous phase. Dissolved CH4, but not CH4 (g), was positively correlated with H2 (aq). Both H2 (aq) and H2 (g) concentrations were positively correlated with the molar percentage of butyrate and negatively correlated with the molar percentage of acetate. In summary, rumen fluid was supersaturated with both H2 and CH4, and H2 (aq) was closely associated with the VFA profile and CH4 (aq) concentration. The assumption of equilibrium between dissolved gases and gaseous phase affected ΔG estimation. PMID:27379028

Pre-digestion to enhance volatile fatty acids (VFAs) concentration as a carbon source for denitrification in treatment of liquid swine manure.

PubMed

Wu, Sarah Xiao; Chen, Lide; Zhu, Jun; Walquist, McKenzie; Christian, David

2018-04-30

Insufficient denitrification in biological treatment is often a result of the lack of a carbon source. In this study, use of the volatile fatty acids (VFAs) generated via pre-digestion as a carbon source to improve denitrification in sequencing batch reactor (SBR) treatment of liquid swine manure was investigated. The pre-digestion of swine manure was realized by storing the manure in a sealed container in room temperature and samples were taken periodically from the container to determine the VFA levels. The results showed that after 14 days of pre-digestion, the VFA level in the digested liquid was increased by 200%. A polynomial relationship for the VFA level in the digested manure with the digestion time was observed with a correlation coefficient being 0.9748. Two identical SBRs were built and operated on 8-h cycles in parallel, with one fed with pre-digested and the other raw swine manure. There were five phases included in each cycle, i.e., anaerobic (90 min), anoxic (150 min), anoxic/anaerobic (90 min), anoxic/aerobic (120 min), and settle/decant (30 min), and the feeding was split to 600 mL/200 mL and performed at the beginning of and 240 min into the cycle. The SBR fed on pre-digested swine manure achieved successful denitrification with only 0.35 mg/L nitrate left in the effluent, compared to 15.9 mg/L found in the effluent of the other SBR. Nitrite was not detected in the effluent from both SBRs. The results also indicated that there was no negative impact of feeding SBRs with the pre-digested liquid swine manure for treatment on the removal of other constituents such as total solids (TS), volatile solids (VS), suspended solids (SS), volatile suspended solids (VSS), and soluble chemical oxygen demand (COD). Therefore, anaerobic digestion as a pretreatment can be an effective way to condition liquid swine manure for SBR treatment to achieve sufficient nitrate removal.

Rapid parametric mapping of the longitudinal relaxation time T1 using two-dimensional variable flip angle magnetic resonance imaging at 1.5 Tesla, 3 Tesla, and 7 Tesla.

PubMed

Dieringer, Matthias A; Deimling, Michael; Santoro, Davide; Wuerfel, Jens; Madai, Vince I; Sobesky, Jan; von Knobelsdorff-Brenkenhoff, Florian; Schulz-Menger, Jeanette; Niendorf, Thoralf

2014-01-01

Visual but subjective reading of longitudinal relaxation time (T1) weighted magnetic resonance images is commonly used for the detection of brain pathologies. For this non-quantitative measure, diagnostic quality depends on hardware configuration, imaging parameters, radio frequency transmission field (B1+) uniformity, as well as observer experience. Parametric quantification of the tissue T1 relaxation parameter offsets the propensity for these effects, but is typically time consuming. For this reason, this study examines the feasibility of rapid 2D T1 quantification using a variable flip angles (VFA) approach at magnetic field strengths of 1.5 Tesla, 3 Tesla, and 7 Tesla. These efforts include validation in phantom experiments and application for brain T1 mapping. T1 quantification included simulations of the Bloch equations to correct for slice profile imperfections, and a correction for B1+. Fast gradient echo acquisitions were conducted using three adjusted flip angles for the proposed T1 quantification approach that was benchmarked against slice profile uncorrected 2D VFA and an inversion-recovery spin-echo based reference method. Brain T1 mapping was performed in six healthy subjects, one multiple sclerosis patient, and one stroke patient. Phantom experiments showed a mean T1 estimation error of (-63±1.5)% for slice profile uncorrected 2D VFA and (0.2±1.4)% for the proposed approach compared to the reference method. Scan time for single slice T1 mapping including B1+ mapping could be reduced to 5 seconds using an in-plane resolution of (2×2) mm2, which equals a scan time reduction of more than 99% compared to the reference method. Our results demonstrate that rapid 2D T1 quantification using a variable flip angle approach is feasible at 1.5T/3T/7T. It represents a valuable alternative for rapid T1 mapping due to the gain in speed versus conventional approaches. This progress may serve to enhance the capabilities of parametric MR based lesion detection and brain tissue characterization.

The Contribution of Mathematical Modeling to Understanding Dynamic Aspects of Rumen Metabolism

PubMed Central

Bannink, André; van Lingen, Henk J.; Ellis, Jennifer L.; France, James; Dijkstra, Jan

2016-01-01

All mechanistic rumen models cover the main drivers of variation in rumen function, which are feed intake, the differences between feedstuffs and feeds in their intrinsic rumen degradation characteristics, and fractional outflow rate of fluid and particulate matter. Dynamic modeling approaches are best suited to the prediction of more nuanced responses in rumen metabolism, and represent the dynamics of the interactions between substrates and micro-organisms and inter-microbial interactions. The concepts of dynamics are discussed for the case of rumen starch digestion as influenced by starch intake rate and frequency of feed intake, and for the case of fermentation of fiber in the large intestine. Adding representations of new functional classes of micro-organisms (i.e., with new characteristics from the perspective of whole rumen function) in rumen models only delivers new insights if complemented by the dynamics of their interactions with other functional classes. Rumen fermentation conditions have to be represented due to their profound impact on the dynamics of substrate degradation and microbial metabolism. Although the importance of rumen pH is generally acknowledged, more emphasis is needed on predicting its variation as well as variation in the processes that underlie rumen fluid dynamics. The rumen wall has an important role in adapting to rapid changes in the rumen environment, clearing of volatile fatty acids (VFA), and maintaining rumen pH within limits. Dynamics of rumen wall epithelia and their role in VFA absorption needs to be better represented in models that aim to predict rumen responses across nutritional or physiological states. For a detailed prediction of rumen N balance there is merit in a dynamic modeling approach compared to the static approaches adopted in current protein evaluation systems. Improvement is needed on previous attempts to predict rumen VFA profiles, and this should be pursued by introducing factors that relate more to microbial metabolism. For rumen model construction, data on rumen microbiomes are preferably coupled with knowledge consolidated in rumen models instead of relying on correlations with rather general aspects of treatment or animal. This helps to prevent the disregard of basic principles and underlying mechanisms of whole rumen function. PMID:27933039

Exogenous addition of H2 for an in situ biogas upgrading through biological reduction of carbon dioxide into methane.

PubMed

Mulat, Daniel Girma; Mosbæk, Freya; Ward, Alastair James; Polag, Daniela; Greule, Markus; Keppler, Frank; Nielsen, Jeppe Lund; Feilberg, Anders

2017-10-01

Biological reduction of CO 2 into CH 4 by exogenous addition of H 2 is a promising technology for upgrading biogas into higher CH 4 content. The aim of this work was to study the feasibility of exogenous H 2 addition for an in situ biogas upgrading through biological conversion of the biogas CO 2 into CH 4. Moreover, this study employed systematic study with isotope analysis for providing comprehensive evidence on the underlying pathways of CH 4 production and upstream processes. Batch reactors were inoculated with digestate originating from a full-scale biogas plant and fed once with maize leaf substrate. Periodic addition of H 2 into the headspace resulted in a completely consumption of CO 2 and a concomitant increase in CH 4 content up to 89%. The microbial community and isotope analysis shows an enrichment of hydrogenotrophic Methanobacterium and the key role of hydrogenotrophic methanogenesis for biogas upgrading to higher CH 4 content. Excess H 2 was also supplied to evaluate its effect on overall process performance. The results show that excess H 2 addition resulted in accumulation of H 2 , depletion of CO 2 and inhibition of the degradation of acetate and other volatile fatty acids (VFA). A systematic isotope analysis revealed that excess H 2 supply led to an increase in dissolved H 2 to the level that thermodynamically inhibit the degradation of VFA and stimulate homo-acetogens for production of acetate from CO 2 and H 2 . The inhibition was a temporary effect and acetate degradation resumed when the excess H 2 was removed as well as in the presence of stoichiometric amount of H 2 and CO 2 . This inhibition mechanism underlines the importance of carefully regulating the H 2 addition rate and gas retention time to the CO 2 production rate, H 2 -uptake rate and growth of hydrogenotrophic methanogens in order to achieve higher CH 4 content without the accumulation of acetate and other VFA. Copyright © 2017 Elsevier Ltd. All rights reserved.

Acute exposure to ergot alkaloids from endophyte-infected tall fescue does not alter absorptive or barrier function of the isolated bovine ruminal epithelium.

PubMed

Foote, A P; Penner, G B; Walpole, M E; Klotz, J L; Brown, K R; Bush, L P; Harmon, D L

2014-07-01

Ergot alkaloids in endophyte-infected (Neotyphodium coenophialum) tall fescue (Lolium arundinaceum) have been shown to cause a reduction in blood flow to the rumen epithelium as well as a decrease in volatile fatty acids (VFA) absorption from the washed rumen of steers. Previous data also indicates that incubating an extract of endophyte-infected tall fescue seed causes an increase in the amount of VFA absorbed per unit of blood flow, which could result from an alteration in the absorptive or barrier function of the rumen epithelium. An experiment was conducted to determine the acute effects of an endophyte-infected tall fescue seed extract (EXT) on total, passive or facilitated acetate and butyrate flux across the isolated bovine rumen as well as the barrier function measured by inulin flux and tissue conductance (G t ). Flux of ergovaline across the rumen epithelium was also evaluated. Rumen tissue from the caudal dorsal sac of Holstein steers (n=6), fed a common diet, was collected and isolated shortly after slaughter and mounted between two halves of Ussing chambers. In vitro treatments included vehicle control (80% methanol, 0.5% of total volume), Low EXT (50 ng ergovaline/ml) and High EXT (250 ng ergovaline/ml). Results indicate that there is no effect of acute exposure to ergot alkaloids on total, passive or facilitated flux of acetate or butyrate across the isolate bovine rumen epithelium (P>0.51). Inulin flux (P=0.16) and G t (P>0.17) were not affected by EXT treatment, indicating no alteration in barrier function due to acute ergot alkaloid exposure. Ergovaline was detected in the serosal buffer of the High EXT treatment indicating that the flux rate is ~0.25 to 0.44 ng/cm2 per hour. Data indicate that specific pathways for VFA absorption and barrier function of the rumen epithelium are not affected by acute exposure to ergot alkaloids from tall fescue at the concentrations tested. Ergovaline has the potential to be absorbed from the rumen of cattle that could contribute to reduced blood flow and motility and lead to reduced growth rates of cattle.

Impact of mash feeding versus pellets on propionic/butyric acid levels and on total load in the gastrointestinal tract of growing pigs.

PubMed

Longpré, J; Fairbrother, J M; Fravalo, P; Arsenault, J; LeBel, P; Laplante, B; Surprenant, C; Massé, D; Letellier, A

2016-03-01

Feed characteristics may influence the bacterial community composition and metabolic activities in the pig gastrointestinal tract, known to be associated with positive effects on the gut. Use of mash feed is associated with reduced excretion, but little is known of its effect on the population or of the mechanism of action. Our objectives were to assess the effect of feed texture combined with feed particle size on VFA profiles and levels, total count, and the presence of genes encoding virulence factors of pathogenic strains in the digestive tract along with their impact on pig performance of fattening pigs. Pigs ( = 840) on a commercial farm received mash or pellet diets of different particle sizes during the fattening period. Caecal and colon contents from 164 pigs were sampled at the slaughterhouse for enumeration of by quantitative PCR (qPCR) and for VFA quantification by capillary gas chromatography. The gene was used to enumerate total . Improved pig performances associated with pellet texture and a 500-μm size were observed. Caecal ( = 0.02) and colon ( < 0.01) propionic acid concentrations were lower for pigs receiving pellet rather than mash feed. Similarly, caecal ( = 0.01) and colon ( < 0.001) butyric acid concentrations were also lower for pigs receiving pellet rather than mash feed, as determined by capillary gas chromatography. Moreover, caecal ( = 0.03) and colon ( < 0.001) butyric acid concentrations were higher for pigs receiving a feed with a 1,250-μm particle size rather than a 500-μm particle size. On the other hand, total caecal and colon levels were higher for pigs receiving pellet feed than for those receiving mash feed. For total enumeration, caecal ( < 0.01) and colon ( < 0.01) gene copies were higher for pigs receiving pellet rather than mash feed. No effect of particle size on fatty acid concentrations or on numbers was observed. Virulence gene quantification revealed no trend. Taken together, results showed that mash feed is associated with lower growth performance but with favorable intestinal changes linked to VFA levels and reduction in the intestine.

A study on relationship between elderly sarcopenia and inflammatory factors IL-6 and TNF-α.

PubMed

Bian, Ai-Lin; Hu, Hui-Ying; Rong, Yu-Dong; Wang, Jian; Wang, Jun-Xiong; Zhou, Xin-Zi

2017-07-12

This report aims to study the relationship between sarcopenia of elderly in community and inflammatory factors IL-6 and TNF-α. A total of 441 elders who undertook physical examinations were included into this study. The age of these subjects were >60, in which 235 subjects were male and 206 subjects were female. According to the diagnostic standards of sarcopenia set by EWGSOP and AWGS, these subjects were divided into two groups: sarcopenia, and non-sarcopenia groups. The living habits, disease status, biochemical indexes, and levels of IL-6 and TNF-α of these subjects were investigated. The morbidity rate of sarcopenia was 17.02% in male subjects and 18.9% in female subjects. In elderly subjects >80 years old, morbidity rate was 25.3% in male subjects and 35.1% in female subjects. The history of smoking in patients with sarcopenia was long, and their regular exercise history was short (P < 0.01). Furthermore, differences in handgrip strength (HG), fat-free mass (FFM), bone mineral content (BMC), plasma albumin (ALB) and serum creatinine (Cr), and body fat content (FAT) in patients between the sarcopenia and non-sarcopenia groups were statistically significant (P < 0.05). Moreover, differences in IL-6 and TNF-α levels between these two groups were statistically significant (P < 0.05). In addition, BMI was positively correlated to TNF-α levels, and ALB was negatively correlated to IL-6; while BMI and VFA were positively correlated to TNF-α levels, and SMM, HDL-C, Hb, HG were negatively correlated to IL-6 level (P < 0.05). Multiple linear regression analysis suggested plasma ALB and BMI were the independent risk factors of TNF-α, while VFA was the independent risk factor of IL-6. The onset of sarcopenia was associated with poor exercise habits, disease history, and nutritional status. The emergence of sarcopenia was accompanied by increased levels of inflammation factors TNF-α and IL-6. Plasma albumin, BMI, and VFA were inflammatory factor predictors of TNF and IL-6.

Nanocrystalline SnO2:F thin films for liquid petroleum gas sensors.

PubMed

Chaisitsak, Sutichai

2011-01-01

This paper reports the improvement in the sensing performance of nanocrystalline SnO(2)-based liquid petroleum gas (LPG) sensors by doping with fluorine (F). Un-doped and F-doped tin oxide films were prepared on glass substrates by the dip-coating technique using a layer-by-layer deposition cycle (alternating between dip-coating a thin layer followed by a drying in air after each new layer). The results showed that this technique is superior to the conventional technique for both improving the film thickness uniformity and film transparency. The effect of F concentration on the structural, surface morphological and LPG sensing properties of the SnO(2) films was investigated. Atomic Force Microscopy (AFM) and X-ray diffraction pattern measurements showed that the obtained thin films are nanocrystalline SnO(2) with nanoscale-textured surfaces. Gas sensing characteristics (sensor response and response/recovery time) of the SnO(2):F sensors based on a planar interdigital structure were investigated at different operating temperatures and at different LPG concentrations. The addition of fluorine to SnO(2) was found to be advantageous for efficient detection of LPG gases, e.g., F-doped sensors are more stable at a low operating temperature (300 °C) with higher sensor response and faster response/recovery time, compared to un-doped sensor materials. The sensors based on SnO(2):F films could detect LPG even at a low level of 25% LEL, showing the possibility of using this transparent material for LPG leak detection.

A Review of Interface Electronic Systems for AT-cut Quartz Crystal Microbalance Applications in Liquids

PubMed Central

Arnau, Antonio

2008-01-01

From the first applications of AT-cut quartz crystals as sensors in solutions more than 20 years ago, the so-called quartz crystal microbalance (QCM) sensor is becoming into a good alternative analytical method in a great deal of applications such as biosensors, analysis of biomolecular interactions, study of bacterial adhesion at specific interfaces, pathogen and microorganism detection, study of polymer film-biomolecule or cell-substrate interactions, immunosensors and an extensive use in fluids and polymer characterization and electrochemical applications among others. The appropriate evaluation of this analytical method requires recognizing the different steps involved and to be conscious of their importance and limitations. The first step involved in a QCM system is the accurate and appropriate characterization of the sensor in relation to the specific application. The use of the piezoelectric sensor in contact with solutions strongly affects its behavior and appropriate electronic interfaces must be used for an adequate sensor characterization. Systems based on different principles and techniques have been implemented during the last 25 years. The interface selection for the specific application is important and its limitations must be known to be conscious of its suitability, and for avoiding the possible error propagation in the interpretation of results. This article presents a comprehensive overview of the different techniques used for AT-cut quartz crystal microbalance in in-solution applications, which are based on the following principles: network or impedance analyzers, decay methods, oscillators and lock-in techniques. The electronic interfaces based on oscillators and phase-locked techniques are treated in detail, with the description of different configurations, since these techniques are the most used in applications for detection of analytes in solutions, and in those where a fast sensor response is necessary. PMID:27879713

Time-frequency analyses of tide-gauge sensor data.

PubMed

Erol, Serdar

2011-01-01

The real world phenomena being observed by sensors are generally non-stationary in nature. The classical linear techniques for analysis and modeling natural time-series observations are inefficient and should be replaced by non-linear techniques of whose theoretical aspects and performances are varied. In this manner adopting the most appropriate technique and strategy is essential in evaluating sensors' data. In this study, two different time-series analysis approaches, namely least squares spectral analysis (LSSA) and wavelet analysis (continuous wavelet transform, cross wavelet transform and wavelet coherence algorithms as extensions of wavelet analysis), are applied to sea-level observations recorded by tide-gauge sensors, and the advantages and drawbacks of these methods are reviewed. The analyses were carried out using sea-level observations recorded at the Antalya-II and Erdek tide-gauge stations of the Turkish National Sea-Level Monitoring System. In the analyses, the useful information hidden in the noisy signals was detected, and the common features between the two sea-level time series were clarified. The tide-gauge records have data gaps in time because of issues such as instrumental shortcomings and power outages. Concerning the difficulties of the time-frequency analysis of data with voids, the sea-level observations were preprocessed, and the missing parts were predicted using the neural network method prior to the analysis. In conclusion the merits and limitations of the techniques in evaluating non-stationary observations by means of tide-gauge sensors records were documented and an analysis strategy for the sequential sensors observations was presented.

Tailoring properties of lossy-mode resonance optical fiber sensors with atomic layer deposition technique

NASA Astrophysics Data System (ADS)

Kosiel, Kamil; Koba, Marcin; Masiewicz, Marcin; Śmietana, Mateusz

2018-06-01

The paper shows application of atomic layer deposition (ALD) technique as a tool for tailoring sensorial properties of lossy-mode-resonance (LMR)-based optical fiber sensors. Hafnium dioxide (HfO2), zirconium dioxide (ZrO2), and tantalum oxide (TaxOy), as high-refractive-index dielectrics that are particularly convenient for LMR-sensor fabrication, were deposited by low-temperature (100 °C) ALD ensuring safe conditions for thermally vulnerable fibers. Applicability of HfO2 and ZrO2 overlays, deposited with ALD-related atomic level thickness accuracy for fabrication of LMR-sensors with controlled sensorial properties was presented. Additionally, for the first time according to our best knowledge, the double-layer overlay composed of two different materials - silicon nitride (SixNy) and TaxOy - is presented for the LMR fiber sensors. The thin films of such overlay were deposited by two different techniques - PECVD (the SixNy) and ALD (the TaxOy). Such approach ensures fast overlay fabrication and at the same time facility for resonant wavelength tuning, yielding devices with satisfactory sensorial properties.

Passive Sensor Integration for Vehicle Self-Localization in Urban Traffic Environment †

PubMed Central

Gu, Yanlei; Hsu, Li-Ta; Kamijo, Shunsuke

2015-01-01

This research proposes an accurate vehicular positioning system which can achieve lane-level performance in urban canyons. Multiple passive sensors, which include Global Navigation Satellite System (GNSS) receivers, onboard cameras and inertial sensors, are integrated in the proposed system. As the main source for the localization, the GNSS technique suffers from Non-Line-Of-Sight (NLOS) propagation and multipath effects in urban canyons. This paper proposes to employ a novel GNSS positioning technique in the integration. The employed GNSS technique reduces the multipath and NLOS effects by using the 3D building map. In addition, the inertial sensor can describe the vehicle motion, but has a drift problem as time increases. This paper develops vision-based lane detection, which is firstly used for controlling the drift of the inertial sensor. Moreover, the lane keeping and changing behaviors are extracted from the lane detection function, and further reduce the lateral positioning error in the proposed localization system. We evaluate the integrated localization system in the challenging city urban scenario. The experiments demonstrate the proposed method has sub-meter accuracy with respect to mean positioning error. PMID:26633420

Microelectromechanical system pressure sensor integrated onto optical fiber by anodic bonding.

PubMed

Saran, Anish; Abeysinghe, Don C; Boyd, Joseph T

2006-03-10

Optical microelectromechanical system pressure sensors based on the principle of Fabry-Perot interferometry have been developed and fabricated using the technique of silicon-to-silicon anodic bonding. The pressure sensor is then integrated onto an optical fiber by a novel technique of anodic bonding without use of any adhesives. In this anodic bonding technique we use ultrathin silicon of thickness 10 microm to bond the optical fiber to the sensor head. The ultrathin silicon plays the role of a stress-reducing layer, which helps the bonding of an optical fiber to silicon having conventional wafer thickness. The pressure-sensing membrane is formed by 8 microm thick ultrathin silicon acting as a membrane, thus eliminating the need for bulk silicon etching. The pressure sensor integrated onto an optical fiber is tested for static response, and experimental results indicate degradation in the fringe visibility of the Fabry-Perot interferometer. This effect was mainly due to divergent light rays from the fiber degrading the fringe visibility. This effect is demonstrated in brief by an analytical model.

Coast Guard's Response to Spilled Oil

ERIC Educational Resources Information Center

Ard, R. W., Jr.

1976-01-01

The Coast Guard utilizes a number of monitoring detectors, sensors, and techniques to find, recover and identify oil spills. Discussed in this article are in-situ and airborne sensors, systems developed to provide clean-up capability such as air deployable anti-pollution transfer system (ADAPTS), and techniques which will determine the source of a…

Frequency band justifications for passive sensors 10.0 to 385 GHz, chapter 2. [for monitoring earth resources and the environment

NASA Technical Reports Server (NTRS)

1976-01-01

Sensitivity requirements of the various measurements obtained by microwave sensors, and radiometry techniques are described. Analytical techniques applied to detailed sharing analyses are discussed. A bibliography of publications pertinent to the scientific justification of frequency requirements for passive microwave remote sensing is included.

Magnetoresistive biosensors for quantitative proteomics

NASA Astrophysics Data System (ADS)

Zhou, Xiahan; Huang, Chih-Cheng; Hall, Drew A.

2017-08-01

Quantitative proteomics, as a developing method for study of proteins and identification of diseases, reveals more comprehensive and accurate information of an organism than traditional genomics. A variety of platforms, such as mass spectrometry, optical sensors, electrochemical sensors, magnetic sensors, etc., have been developed for detecting proteins quantitatively. The sandwich immunoassay is widely used as a labeled detection method due to its high specificity and flexibility allowing multiple different types of labels. While optical sensors use enzyme and fluorophore labels to detect proteins with high sensitivity, they often suffer from high background signal and challenges in miniaturization. Magnetic biosensors, including nuclear magnetic resonance sensors, oscillator-based sensors, Hall-effect sensors, and magnetoresistive sensors, use the specific binding events between magnetic nanoparticles (MNPs) and target proteins to measure the analyte concentration. Compared with other biosensing techniques, magnetic sensors take advantage of the intrinsic lack of magnetic signatures in biological samples to achieve high sensitivity and high specificity, and are compatible with semiconductor-based fabrication process to have low-cost and small-size for point-of-care (POC) applications. Although still in the development stage, magnetic biosensing is a promising technique for in-home testing and portable disease monitoring.

Biosensing Using Magnetic Particle Detection Techniques

PubMed Central

Chen, Yi-Ting; Kolhatkar, Arati G.; Zenasni, Oussama; Xu, Shoujun

2017-01-01

Magnetic particles are widely used as signal labels in a variety of biological sensing applications, such as molecular detection and related strategies that rely on ligand-receptor binding. In this review, we explore the fundamental concepts involved in designing magnetic particles for biosensing applications and the techniques used to detect them. First, we briefly describe the magnetic properties that are important for bio-sensing applications and highlight the associated key parameters (such as the starting materials, size, functionalization methods, and bio-conjugation strategies). Subsequently, we focus on magnetic sensing applications that utilize several types of magnetic detection techniques: spintronic sensors, nuclear magnetic resonance (NMR) sensors, superconducting quantum interference devices (SQUIDs), sensors based on the atomic magnetometer (AM), and others. From the studies reported, we note that the size of the MPs is one of the most important factors in choosing a sensing technique. PMID:28994727

Comparison of Calibration Techniques for Low-Cost Air Quality Monitoring

NASA Astrophysics Data System (ADS)

Malings, C.; Ramachandran, S.; Tanzer, R.; Kumar, S. P. N.; Hauryliuk, A.; Zimmerman, N.; Presto, A. A.

2017-12-01

Assessing the intra-city spatial distribution and temporal variability of air quality can be facilitated by a dense network of monitoring stations. However, the cost of implementing such a network can be prohibitive if high-quality but high-cost monitoring systems are used. To this end, the Real-time Affordable Multi-Pollutant (RAMP) sensor package has been developed at the Center for Atmospheric Particle Studies of Carnegie Mellon University, in collaboration with SenSevere LLC. This self-contained unit can measure up to five gases out of CO, SO2, NO, NO2, O3, VOCs, and CO2, along with temperature and relative humidity. Responses of individual gas sensors can vary greatly even when exposed to the same ambient conditions. Those of VOC sensors in particular were observed to vary by a factor-of-8, which suggests that each sensor requires its own calibration model. To this end, we apply and compare two different calibration methods to data collected by RAMP sensors collocated with a reference monitor station. The first method, random forest (RF) modeling, is a rule-based method which maps sensor responses to pollutant concentrations by implementing a trained sequence of decision rules. RF modeling has previously been used for other RAMP gas sensors by the group, and has produced precise calibrated measurements. However, RF models can only predict pollutant concentrations within the range observed in the training data collected during the collocation period. The second method, Gaussian process (GP) modeling, is a probabilistic Bayesian technique whereby broad prior estimates of pollutant concentrations are updated using sensor responses to generate more refined posterior predictions, as well as allowing predictions beyond the range of the training data. The accuracy and precision of these techniques are assessed and compared on VOC data collected during the summer of 2017 in Pittsburgh, PA. By combining pollutant data gathered by each RAMP sensor and applying appropriate calibration techniques, the potentially noisy or biased responses of individual sensors can be mapped to pollutant concentration values which are comparable to those of reference instruments.

Evaluation and Improvement of Eddy Current Position Sensors in Magnetically Suspended Flywheel Systems

NASA Technical Reports Server (NTRS)

Dever, Timothy P.; Palazzolo, Alan B.; Thomas, Erwin M., III; Jansen, Ralph H.; McLallin, Kerry (Technical Monitor); Soeder, James (Technical Monitor)

2001-01-01

Eddy current position sensor performance is evaluated for use in a high-speed flywheel development system. The flywheel utilizes a five axis active magnetic bearing system. The eddy current sensors are used for position feedback for the bearing controller. Measured characteristics include sensitivity to multiple target materials and susceptibility to noise from the magnetic bearings and from sensor-to-sensor crosstalk. Improvements in axial sensor configuration and techniques for noise reduction are described.

Multisensor fusion for the detection of mines and minelike targets

NASA Astrophysics Data System (ADS)

Hanshaw, Terilee

1995-06-01

The US Army's Communications and Electronics Command through the auspices of its Night Vision and Electronics Sensors Directorate (CECOM-NVESD) is actively applying multisensor techniques to the detection of mine targets. This multisensor research results from the 'detection activity' with its broad range of operational conditions and targets. Multisensor operation justifies significant attention by yielding high target detection and low false alarm statistics. Furthermore, recent advances in sensor and computing technologies make its practical application realistic and affordable. The mine detection field-of-endeavor has since its WWI baptismal investigated the known spectra for applicable mine observation phenomena. Countless sensors, algorithms, processors, networks, and other techniques have been investigated to determine candidacy for mine detection. CECOM-NVESD efforts have addressed a wide range of sensors spanning the spectrum from gravity field perturbations, magentic field disturbances, seismic sounding, electromagnetic fields, earth penetrating radar imagery, and infrared/visible/ultraviolet surface imaging technologies. Supplementary analysis has considered sensor candidate applicability by testing under field conditions (versus laboratory), in determination of fieldability. As these field conditions directly effect the probability of detection and false alarms, sensor employment and design must be considered. Consequently, as a given sensor's performance is influenced directly by the operational conditions, tradeoffs are necessary. At present, mass produced and fielded mine detection techniques are limited to those incorporating a single sensor/processor methodology such as, pulse induction and megnetometry, as found in hand held detectors. The most sensitive fielded systems can detect minute metal components in small mine targets but result in very high false alarm rates reducing velocity in operation environments. Furthermore, the actual speed of advance for the entire mission (convoy, movement to engagement, etc.) is determined by the level of difficulty presented in clearance or avoidance activities required in response to the potential 'targets' marked throughout a detection activity. Therefore the application of fielded hand held systems to convoy operations in clearly impractical. CECOM-NVESD efforts are presently seeking to overcome these operational limitations by substantially increasing speed of detection while reducing the false alarm rate through the application of multisensor techniques. The CECOM-NVESD application of multisensor techniques through integration/fusion methods will be defined in this paper.

A Miniaturized QEPAS Trace Gas Sensor with a 3D-Printed Acoustic Detection Module.

PubMed

Yang, Xiaotao; Xiao, Youhong; Ma, Yufei; He, Ying; Tittel, Frank K

2017-07-31

A 3D printing technique was introduced to a quartz-enhanced photoacoustic spectroscopy (QEPAS) sensor and is reported for the first time. The acoustic detection module (ADM) was designed and fabricated using the 3D printing technique and the ADM volume was compressed significantly. Furthermore, a small grin lens was used for laser focusing and facilitated the beam adjustment in the 3D-printed ADM. A quartz tuning fork (QTF) with a low resonance frequency of 30.72 kHz was used as the acoustic wave transducer and acetylene (C₂H₂) was chosen as the analyte. The reported miniaturized QEPAS trace gas sensor is useful in actual sensor applications.

Synergistic impact of sonic-tenside on biomass disintegration potential: Acidogenic and methane potential studies, kinetics and cost analytics.

PubMed

Tamilarasan, K; Arulazhagan, P; Rani, R Uma; Kaliappan, S; Banu, J Rajesh

2018-04-01

An exploration into the symbiotic impact of sonic-tenside (SDBS - sodium dodecyl benzene sulfonate) on biomass disintegration potential and to reduce the energy consumption was studied. At optimized condition (specific energy input 9600 kJ/kg TS; SDBS dosage 0.07 g/g SS), higher percentage of biomass lysis and solids reduction (23.9% and 19.8%) was obtained in blended sonic-tenside disintegration (STD), than sonic disintegration (SD) (17.6% and 9.8%). The bioacidogenic potential (BAP) assay in terms of volatile fatty acids (VFA) production (722 mg/L) was found to be higher for STD, in comparison to SD (350 mg/L). The impact of STD on anaerobic digestion was evident from its methane yield (0.239 g/g COD), higher than SD (0.182 g/g COD). A monetary evaluation of the present study provides a net gain of 2 USD/ton for STD, indicating the profitability of the technique. Copyright © 2018 Elsevier Ltd. All rights reserved.

Enhancing the functional and economical efficiency of a novel combined thermo chemical disperser disintegration of waste activated sludge for biogas production.

PubMed

Kavitha, S; Jayashree, C; Adish Kumar, S; Kaliappan, S; Rajesh Banu, J

2014-12-01

In this investigation, an effort was made to pretreat surplus waste activated sludge (WAS) inexpensively by a novel combined process involving thermo chemical disperser pretreatment. This pretreatment was found to be efficient at a specific energy (SE) consumption of 3360.94 kJ/kg TS, with the chemical oxygen demand (COD) solubilization of 20%. This was comparatively higher than thermo chemically treated sludge where the solubilization was found to be 15.5% at a specific energy consumption of 10,330 kJ/kg TS respectively. Higher production of volatile fatty acids (VFA) (675 mg/L) in anaerobic fermentation of pretreated WAS indicates better hydrolysis performance. The biogas production potential of sludge pretreated through this combined technique was found to be 0.455 (L/gVS) and comparatively higher than thermo chemically pretreated sludge. Economic investigation provides 90% net energy savings in this combined pretreatment. Therefore, this combined process was considered to be potentially effective and economical in sludge disintegration. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effect of an isoflavonid-rich liquorice extract on fermentation, methanogenesis and the microbiome in the rumen simulation technique.

PubMed

Ramos-Morales, E; Rossi, G; Cattin, M; Jones, E; Braganca, R; Newbold, C J

2018-03-01

Due to the antimicrobial activity of flavonoids, it has been suggested that they may provide a possible alternative to antibiotics to stimulate productivity and reduce the environmental load of ruminant agriculture. We hypothesised that an extract of liquorice, rich in prenylated isoflavonoids and particularly glabridin, might potentially improve the efficiency of nitrogen utilisation and reduce methane production in the rumen. When added to a long-term rumen simulating fermentor (RUSITEC), liquorice extract at 1 g L-1 decreased ammonia production (-51%; P < 0.001) without affecting the overall fermentation process. When added at 2 g L-1, decreases in not only ammonia production (-77%; P < 0.001), but also methane (-27%; P = 0.039) and total VFA production (-15%; P = 0.003) were observed. These effects in fermentation were probably related to a decrease in protozoa numbers, a less diverse bacteria population as well as changes in the structure of both the bacterial and archaeal communities. The inclusion of an isoflavonoid-rich extract from liquorice in the diet may potentially improve the efficiency of the feed utilisation by ruminants.

Novel E-Field Sensor for Projectile Detection

DTIC Science & Technology

2012-10-22

aircrafts. They used an array of three plate induction sensors and a simple algorithm to deter mine the direction of the planes [9]. In more recent...publications [10, 11, 12] researchers present increasingly more advanced algorithms and sensors. The techniques developed thus far have not received...the electric field pulse is being detected by a group of sensors in array with known distances between the sensors, so triangulation algorithms could

Multipath Routing in Wireless Sensor Networks: Survey and Research Challenges

PubMed Central

Radi, Marjan; Dezfouli, Behnam; Bakar, Kamalrulnizam Abu; Lee, Malrey

2012-01-01

A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks. PMID:22368490

Multipath routing in wireless sensor networks: survey and research challenges.

PubMed

Radi, Marjan; Dezfouli, Behnam; Abu Bakar, Kamalrulnizam; Lee, Malrey

2012-01-01

A wireless sensor network is a large collection of sensor nodes with limited power supply and constrained computational capability. Due to the restricted communication range and high density of sensor nodes, packet forwarding in sensor networks is usually performed through multi-hop data transmission. Therefore, routing in wireless sensor networks has been considered an important field of research over the past decade. Nowadays, multipath routing approach is widely used in wireless sensor networks to improve network performance through efficient utilization of available network resources. Accordingly, the main aim of this survey is to present the concept of the multipath routing approach and its fundamental challenges, as well as the basic motivations for utilizing this technique in wireless sensor networks. In addition, we present a comprehensive taxonomy on the existing multipath routing protocols, which are especially designed for wireless sensor networks. We highlight the primary motivation behind the development of each protocol category and explain the operation of different protocols in detail, with emphasis on their advantages and disadvantages. Furthermore, this paper compares and summarizes the state-of-the-art multipath routing techniques from the network application point of view. Finally, we identify open issues for further research in the development of multipath routing protocols for wireless sensor networks.

Machine learning techniques for fault isolation and sensor placement

NASA Technical Reports Server (NTRS)

Carnes, James R.; Fisher, Douglas H.

1993-01-01

Fault isolation and sensor placement are vital for monitoring and diagnosis. A sensor conveys information about a system's state that guides troubleshooting if problems arise. We are using machine learning methods to uncover behavioral patterns over snapshots of system simulations that will aid fault isolation and sensor placement, with an eye towards minimality, fault coverage, and noise tolerance.

Performance Analysis of Receive Diversity in Wireless Sensor Networks over GBSBE Models

PubMed Central

Goel, Shivali; Abawajy, Jemal H.; Kim, Tai-hoon

2010-01-01

Wireless sensor networks have attracted a lot of attention recently. In this paper, we develop a channel model based on the elliptical model for multipath components involving randomly placed scatterers in the scattering region with sensors deployed on a field. We verify that in a sensor network, the use of receive diversity techniques improves the performance of the system. Extensive performance analysis of the system is carried out for both single and multiple antennas with the applied receive diversity techniques. Performance analyses based on variations in receiver height, maximum multipath delay and transmit power have been performed considering different numbers of antenna elements present in the receiver array, Our results show that increasing the number of antenna elements for a wireless sensor network does indeed improve the BER rates that can be obtained. PMID:22163510

Civil infrastructure monitoring for IVHS using optical fiber sensors

NASA Astrophysics Data System (ADS)

de Vries, Marten J.; Arya, Vivek; Grinder, C. R.; Murphy, Kent A.; Claus, Richard O.

1995-01-01

8Early deployment of Intelligent Vehicle Highway Systems would necessitate the internal instrumentation of infrastructure for emergency preparedness. Existing quantitative analysis and visual analysis techniques are time consuming, cost prohibitive, and are often unreliable. Fiber optic sensors are rapidly replacing conventional instrumentation because of their small size, light weight, immunity to electromagnetic interference, and extremely high information carrying capability. In this paper research on novel optical fiber sensing techniques for health monitoring of civil infrastructure such as highways and bridges is reported. Design, fabrication, and implementation of fiber optic sensor configurations used for measurements of strain are discussed. Results from field tests conducted to demonstrate the effectiveness of fiber sensors at determining quantitative strain vector components near crack locations in bridges are presented. Emerging applications of fiber sensors for vehicle flow, vehicle speed, and weigh-in-motion measurements are also discussed.

Monitoring of bacteria growth using a wireless, remote query resonant-circuit sensor: application to environmental sensing

NASA Technical Reports Server (NTRS)

Ong, K. G.; Wang, J.; Singh, R. S.; Bachas, L. G.; Grimes, C. A.; Daunert, S. (Principal Investigator)

2001-01-01

A new technique is presented for in-vivo remote query measurement of the complex permittivity spectra of a biological culture solution. A sensor comprised of a printed inductor-capacitor resonant-circuit is placed within the culture solution of interest, with the impedance spectrum of the sensor measured using a remotely located loop antenna; the complex permittivity spectra of the culture is calculated from the measured impedance spectrum. The remote query nature of the sensor platform enables, for example, the in-vivo real-time monitoring of bacteria or yeast growth from within sealed opaque containers. The wireless monitoring technique does not require a specific alignment between sensor and antenna. Results are presented for studies conducted on laboratory strains of Bacillus subtilis, Escherichia coli JM109, Pseudomonas putida and Saccharomyces cerevisiae.

Recent Development in Optical Chemical Sensors Coupling with Flow Injection Analysis

PubMed Central

Ojeda, Catalina Bosch; Rojas, Fuensanta Sánchez

2006-01-01

Optical techniques for chemical analysis are well established and sensors based on these techniques are now attracting considerable attention because of their importance in applications such as environmental monitoring, biomedical sensing, and industrial process control. On the other hand, flow injection analysis (FIA) is advisable for the rapid analysis of microliter volume samples and can be interfaced directly to the chemical process. The FIA has become a widespread automatic analytical method for more reasons; mainly due to the simplicity and low cost of the setups, their versatility, and ease of assembling. In this paper, an overview of flow injection determinations by using optical chemical sensors is provided, and instrumentation, sensor design, and applications are discussed. This work summarizes the most relevant manuscripts from 1980 to date referred to analysis using optical chemical sensors in FIA.

Characteristic vector analysis of inflection ratio spectra: New technique for analysis of ocean color data

NASA Technical Reports Server (NTRS)

Grew, G. W.

1985-01-01

Characteristic vector analysis applied to inflection ratio spectra is a new approach to analyzing spectral data. The technique applied to remote data collected with the multichannel ocean color sensor (MOCS), a passive sensor, simultaneously maps the distribution of two different phytopigments, chlorophyll alpha and phycoerythrin, the ocean. The data set presented is from a series of warm core ring missions conducted during 1982. The data compare favorably with a theoretical model and with data collected on the same mission by an active sensor, the airborne oceanographic lidar (AOL).

Transient plasma estimation: a noise cancelling/identification approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Candy, J.V.; Casper, T.; Kane, R.

1985-03-01

The application of a noise cancelling technique to extract energy storage information from sensors occurring during fusion reactor experiments on the Tandem Mirror Experiment-Upgrade (TMX-U) at the Lawrence Livermore National Laboratory (LLNL) is examined. We show how this technique can be used to decrease the uncertainty in the corresponding sensor measurements used for diagnostics in both real-time and post-experimental environments. We analyze the performance of algorithm on the sensor data and discuss the various tradeoffs. The algorithm suggested is designed using SIG, an interactive signal processing package developed at LLNL.

Single-ended retroreflection sensors for absorption spectroscopy in high-temperature environments

NASA Astrophysics Data System (ADS)

Melin, Scott T.; Wang, Ze; Neal, Nicholas J.; Rothamer, David A.; Sanders, Scott T.

2017-04-01

Novel single-ended sensor arrangements are demonstrated for in situ absorption spectroscopy in combustion and related test articles. A single-ended optical access technique based on back-reflection from a polished test article surface is presented. H2O vapor absorption spectra were measured at 10 kHz in a homogeneous-charge compression-ignition engine using a sensor of this design collecting back-reflection from a polished piston surface. The measured spectra show promise for high-repetition-rate measurements in practical combustion devices. A second sensor was demonstrated based on a modification to this optical access technique. The sensor incorporates a nickel retroreflective surface as back-reflector to reduce sensitivity to beam steering and misalignment. In a propane-fired furnace, H2O vapor absorption spectra were obtained over the range 7315-7550 cm- 1 at atmospheric pressure and temperatures up to 775 K at 20 Hz using an external-cavity diode laser spectrometer. Gas properties of temperature and mole fraction were obtained from this furnace data using a band-shape spectral fitting technique. The temperature accuracy of the band-shape fitting was demonstrated to be ±1.3 K for furnace measurements at atmospheric pressure. These results should extend the range of applications in which absorption spectroscopy sensors are attractive candidates.