Dietary fiber intake and retinal vascular caliber in the Atherosclerosis Risk in Communities Study.

PubMed

Kan, Haidong; Stevens, June; Heiss, Gerardo; Klein, Ronald; Rose, Kathryn M; London, Stephanie J

2007-12-01

Dietary fiber appears to decrease the risk of cardiovascular morbidity and mortality. Microvascular abnormalities can be observed by retinal examination and contribute to the pathogenesis of various cardiovascular diseases. The impact of dietary fiber on the retinal microvasculature is not known. We aimed to examine the association between dietary fiber intake and retinal vascular caliber. At the third visit (1993-1995) of the Atherosclerosis Risk in Communities (ARIC) Study, a population-based cohort of adults in 4 US communities, the retinal vascular caliber of 10,659 participants was measured and summarized from digital retinal photographs. Usual dietary intake during the same period was assessed with a 66-item food-frequency questionnaire. After control for potential confounders including hypertension, diabetes, lipids, demographic factors, cigarette smoking, total energy intake, micronutrients intake, and other cardiovascular disease risk factors, higher intake of fiber from all sources and from cereal were significantly associated with wider retinal arteriolar caliber and narrower venular caliber. Participants in the highest quintile of fiber intake from all sources had a 1.05-microm larger arteriolar caliber (P for trend = 0.012) and a 1.11-microm smaller venular caliber (P for trend = 0.029). Dietary fiber was related to wider retinal arteriolar caliber and narrower venular caliber, which are associated with a lower risk of cardiovascular disease. These data add to the growing evidence of the benefits of fiber intake on various aspects of cardiovascular pathogenesis.

Multi-passes warm rolling of AZ31 magnesium alloy, effect on evaluation of texture, microstructure, grain size and hardness

NASA Astrophysics Data System (ADS)

Kamran, J.; Hasan, B. A.; Tariq, N. H.; Izhar, S.; Sarwar, M.

2014-06-01

In this study the effect of multi-passes warm rolling of AZ31 magnesium alloy on texture, microstructure, grain size variation and hardness of as cast sample (A) and two rolled samples (B & C) taken from different locations of the as-cast ingot was investigated. The purpose was to enhance the formability of AZ31 alloy in order to help manufacturability. It was observed that multi-passes warm rolling (250°C to 350°C) of samples B & C with initial thickness 7.76mm and 7.73 mm was successfully achieved up to 85% reduction without any edge or surface cracks in ten steps with a total of 26 passes. The step numbers 1 to 4 consist of 5, 2, 11 and 3 passes respectively, the remaining steps 5 to 10 were single pass rolls. In each discrete step a fixed roll gap is used in a way that true strain per step increases very slowly from 0.0067 in the first step to 0.7118 in the 26th step. Both samples B & C showed very similar behavior after 26th pass and were successfully rolled up to 85% thickness reduction. However, during 10th step (27th pass) with a true strain value of 0.772 the sample B experienced very severe surface as well as edge cracks. Sample C was therefore not rolled for the 10th step and retained after 26 passes. Both samples were studied in terms of their basal texture, microstructure, grain size and hardness. Sample C showed an equiaxed grain structure after 85% total reduction. The equiaxed grain structure of sample C may be due to the effective involvement of dynamic recrystallization (DRX) which led to formation of these grains with relatively low misorientations with respect to the parent as cast grains. The sample B on the other hand showed a microstructure in which all the grains were elongated along the rolling direction (RD) after 90 % total reduction and DRX could not effectively play its role due to heavy strain and lack of plastic deformation systems. The microstructure of as cast sample showed a near-random texture (mrd 4.3), with average grain size of 44 & micro-hardness of 52 Hv. The grain size of sample B and C was 14μm and 27μm respectively and mrd intensity of basal texture was 5.34 and 5.46 respectively. The hardness of sample B and C came out to be 91 and 66 Hv respectively due to reduction in grain size and followed the well known Hall-Petch relationship.

27 CFR 447.52 - Import restrictions applicable to certain countries.

Code of Federal Regulations, 2010 CFR

2010-04-01

.../Revolvers: (A) German Model P08 Pistol. (B) IZH 34M, .22 caliber Target Pistol. (C) IZH 35M, .22 caliber... caliber Target Rifle (also known as SM2, 22 caliber). (E) German Model 98K Rifle. (F) German Model G41 Rifle. (G) German Model G43 Rifle. (H) IZH-94. (I) LOS-7 Bolt Action Rifle. (J) MC-7-07. (K) MC-18-3. (L...

Retinal microvasculature and white matter microstructure: The Rotterdam Study.

PubMed

Mutlu, Unal; Cremers, Lotte G M; de Groot, Marius; Hofman, Albert; Niessen, Wiro J; van der Lugt, Aad; Klaver, Caroline C W; Ikram, M Arfan; Vernooij, Meike W; Ikram, M Kamran

2016-09-06

To investigate whether retinal microvascular damage is related to normal-appearing white matter microstructure on diffusion tensor MRI. We included 2,436 participants (age ≥45 years) from the population-based Rotterdam Study (2005-2009) who had gradable retinal images and brain MRI scans. Retinal arteriolar and venular calibers were measured semiautomatically on fundus photographs. White matter microstructure was assessed using diffusion tensor MRI. We used linear regression models to investigate the associations of retinal vascular calibers with markers of normal-appearing white matter microstructure, adjusting for age, sex, the fellow vascular caliber, and additionally for structural MRI markers and cardiovascular risk factors. Narrower arterioles and wider venules were associated with poor white matter microstructure: adjusted difference in fractional anisotropy per SD decrease in arteriolar caliber -0.061 (95% confidence interval -0.106 to -0.016), increase in venular caliber -0.054 (-0.096 to -0.011), adjusted difference in mean diffusivity per SD decrease in arteriolar caliber 0.048 (0.007-0.088), and increase in venular caliber 0.047 (0.008-0.085). The associations for venules were more prominent in women. Retinal vascular calibers are related to normal-appearing white matter microstructure. This suggests that microvascular damage in the white matter is more widespread than visually detectable as white matter lesions. © 2016 American Academy of Neurology.

Regulation Mechanism of Novel Thermomechanical Treatment on Microstructure and Properties in Al-Zn-Mg-Cu Alloy

NASA Astrophysics Data System (ADS)

Chen, Zhiguo; Ren, Jieke; Zhang, Jishuai; Chen, Jiqiang; Fang, Liang

2016-02-01

Scanning electron microscopy, transmission electron microscopy, tensile test, exfoliation corrosion test, and slow strain rate tensile test were applied to investigate the properties and microstructure of Al-Zn-Mg-Cu alloy processed by final thermomechanical treatment, retrogression reaging, and novel thermomechanical treatment (a combination of retrogression reaging with cold or warm rolling). The results indicate that in comparison with conventional heat treatment, the novel thermomechanical treatment reduces the stress corrosion susceptibility. A good combination of mechanical properties, stress corrosion resistance, and exfoliation corrosion resistance can be obtained by combining retrogression reaging with warm rolling. The mechanism of the novel thermomechanical treatment is the synergistic effect of composite microstructure such as grain morphology, dislocation substructures, as well as the morphology and distribution of primary phases and precipitations.

Diapering Your Baby

MedlinePlus

... prefold diapers) a container of warm water and cotton balls (for babies with sensitive skin) or a ... ability to roll. Wiping Using the wet washcloth, cotton balls, or baby wipes, gently wipe your baby ...

Crystallographic texture of straight-rolled ?-uranium foils via neutron and X-ray diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Einhorn, J. R.; Steiner, M. A.; Vogel, S. C.

The texture of recrystallized straight-rolled ?-uranium foils, a component in prospective irradiation target designs for medical isotope production, has been measured by neutron diffraction, as well as X-ray diffraction using both Cu and Mo sources. Variations in the penetration depth of neutron and X-ray radiation allow for determination of both the bulk and surface textures. The bulk ?-uranium foil texture is similar to the warm straight-rolled plate texture, with the addition of a notable splitting of the (001) poles along the transverse direction. The surface texture of the foils is similar to the bulk, with an additional (001) texture componentmore » that is oriented between the rolling and normal directions. Differences between the surface and bulk textures are expected to arise from shear forces during the rolling process and the influence that distinct strain histories have on subsequent texture evolution during recrystallization.« less

Crystallographic texture of straight-rolled ?-uranium foils via neutron and X-ray diffraction

DOE PAGES

Einhorn, J. R.; Steiner, M. A.; Vogel, S. C.; ...

2017-05-25

The texture of recrystallized straight-rolled ?-uranium foils, a component in prospective irradiation target designs for medical isotope production, has been measured by neutron diffraction, as well as X-ray diffraction using both Cu and Mo sources. Variations in the penetration depth of neutron and X-ray radiation allow for determination of both the bulk and surface textures. The bulk ?-uranium foil texture is similar to the warm straight-rolled plate texture, with the addition of a notable splitting of the (001) poles along the transverse direction. The surface texture of the foils is similar to the bulk, with an additional (001) texture componentmore » that is oriented between the rolling and normal directions. Differences between the surface and bulk textures are expected to arise from shear forces during the rolling process and the influence that distinct strain histories have on subsequent texture evolution during recrystallization.« less

Damage Analysis of Tensile Deformation of Co-rolled SMATed 304SS

NASA Astrophysics Data System (ADS)

Guo, X.; Leung, A. Y. T.; Chen, A.; Ruan, H.; Lu, J.

2010-05-01

One of recent experimental progresses in strengthening and toughening metals simultaneously is to adopt techniques of surface mechanical attrition treatment (SMAT) and warm co-rolling to 304 stainless steel (SS). To capture deformation behavior and associated damage initiation/evolution process in the co-rolled SMATed 304SS, cohesive finite element method (CFEM) is employed in this paper and simulation results are in agreement with experimental results. Both strengthening effect due to high yield stress of the nanograin layer and toughening effect due to non-localized damage in the nanograin layer are captured. Effect of energy release rate of nanograin layer on failure strain of layered co-rolled SMATed 304SS is investigated. It is found that the more brittle the nanograin layer is, the more potential necking sites in the nanograin layer are, and the more ductile the layered co-rolled SMATed 304SS is.

Computed tomographic evaluation to determine efficacy of euthanasia of yearling feedlot cattle by use of various firearm-ammunition combinations.

PubMed

Thomson, Daniel U; Wileman, Benjamin W; Rezac, Darrel J; Miesner, Matt D; Johnson-Neitman, Jennifer L; Biller, David S

2013-11-01

To evaluate with CT the efficacy of various combinations of firearms and ammunitions to penetrate and disrupt the brain tissue of cadaveric heads of feedlot steers. 42 fresh cadaveric heads of 12- to 18-month-old Bos taurus steers. For each of 7 combinations of firearms and ammunitions (.22-caliber rifle firing a long rifle 30-grain plated lead solid- or hollow-point round, .223-caliber carbine firing a 50-grain ballistic-tip round, 9-mm pistol firing a 124-grain total metal jacket round, .45-caliber automatic Colt pistol [ACP] firing a 230-grain full metal jacket round, and 12-gauge shotgun firing a 2.75-inch 1.25-ounce No. 4 birdshot shell or a 1-ounce rifled slug), 6 cadaveric heads were shot at an identical distance (3 m), angle, and anatomic location. Heads were scanned with third-generation CT, and images were evaluated to determine extent of penetration, projectile fragmentation, cranial fracture, and likelihood of instantaneous death (≥ 30% destruction of brain tissue or a brainstem lesion). RESULTS-41 of 42 skulls were penetrated by the projectile. Instantaneous death was considered a likely consequence for 83% (25/30) of heads shot with a rifle-fired .22-caliber solid-point round, pistol-fired .45-caliber ACP round, carbine-fired .223-caliber round, and shotgun-fired birdshot and slug. Of the 18 heads shot with pistol-fired 9-mm and .45-caliber ACP rounds and rifle-fired .22-caliber hollow-point rounds, only 6 had brainstem lesions. CONCLUSIONS AND CLINICAL RELEVANCE-Results suggested that gunshots delivered by all firearm-ammunition combinations except rifle-fired .22-caliber hollow-point rounds and pistol-fired 9-mm rounds were viable options for euthanasia of feedlot cattle.

Effect of caliber size and fat level on the inactivation of E. coli O157:H7 in dry fermented sausages.

PubMed

De Souza, James; Ahmed, Rafath; Strange, Philip; Barbut, Shai; Balamurugan, S

2018-02-02

Dry fermented sausages (DFS) have been subject to numerous validation studies, as pathogen reduction heavily relies on both ingredients and processing. In this study the effect of product caliber size (32, 55, 80mm), and fat level (low, 9.67%; high, 18.46% wt/wt) on the inactivation of E. coli O157:H7 during DFS production was examined. Sausages containing a five-strain cocktail of E. coli O157:H7 at 10 7 CFU/g were manufactured and monitored for changes in physicochemical properties and inoculated E. coli O157:H7 numbers were enumerated during the DFS production stages and log reduction rates were calculated. Significant (P<0.01) reduction in pH from 5.9 to 4.9 was observed in all sausages within 72h of fermentation; however, the observed pH reduction was not significantly (P>0.05) different among sausages of different caliber size or fat levels. No significant (P>0.05) reduction in a w was observed during fermentation of the sausages. However, during the drying phase, sausages with larger caliber sizes required a significantly longer duration of drying to achieve the same a w of smaller caliber size sausages. For instance, to achieve an a w of ≤0.9, following 5days of fermentation/curing, 80mm caliber sausages required up to 27days of drying compared with 13 and 6days for 55 and 32mm caliber size sausages, respectively. Fat levels on the other hand did not significantly (P>0.05) effect the reduction of a w during drying of the sausages. During the fermentation stage there was a significant and rapid reduction in E. coli O157:H7 counts by about 1.1- to 1.4-log units, but was not significantly different among sausages of different caliber size and fat levels. Considering the whole process, only caliber size had a significant effect on log reduction of E. coli O157:H7. ANOVA of log reduction rates of E. coli O157:H7 among sausages of different caliber size and fat levels revealed no significant differences during the fermentation, however, during the drying of the sausages, log reduction rate of E. coli O157:H7 was significantly (P<0.01) lower in sausages with larger caliber sizes and higher fat levels. For instance, log reduction rates for E. coli O157:H7 in high fat large caliber sausages was the lowest at -0.082±0.004 log CFU/g/day compared to all other fat and caliber size combinations. These results suggest that DFS manufacturers producing higher fat and large caliber size products need to consider longer drying periods to achieve the required 5-log inactivation of E. coli O157:H7. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Progress in the Development of a Multiphase Turbulent Model of the Gas/Particle Flow in a Small-Caliber Ammunition Primer

DTIC Science & Technology

2006-08-01

Maneuver Ammunition Systems is acknowledged for continued support of this effort. This research was performed while the first author held a National...the ignition system (i.e., the primer in small-caliber guns, the primer and flashtube in medium-caliber guns, and the primer and igniter-tube in large...primer model that is compatible with the ARL- NGEN3 IB code is the subject of this report. The conventional ignition system for a large-caliber (120 mm

Towards the damage evaluation using Gurson-Tvergaard-Needleman (GTN) model for hot forming processes

NASA Astrophysics Data System (ADS)

Imran, Muhammad; Bambach, Markus

2018-05-01

In the production of semi-finished metal products, hot forming is used to eliminate the pores and voids from the casting process under compressive stresses and to modify the microstructure for further processing. In the case of caliber and flat rolling processes, tensile stresses occur at certain roll gap ratios which promote pore formation on nonmetallic inclusion. The formation of new pores contributes to ductile damage and reduces the load carrying capacity of the material. In the literature, the damage nucleation and growth during the hot forming process are not comprehensively described. The aim of this study is to understand the damage initiation and growth mechanism during hot forming processes. Hot tensile tests are performed at different temperatures and strain rates for 16MnCrS5 steel. To investigate the influence of geometrical variations on the damage mechanism, specimens with different stress triaxiality ratios are used. Finite element simulations using the Gurson-Tvergaard-Needleman (GTN) damage model are performed to estimate the critical void fraction for the damage initiation and the evolution of the void volume fraction. The results showed that the GTN model underestimates the softening of the material due to the independence of the temperature and the strain rate.

Advances In Understanding Global Water Cycle With Advent of GPM Mission

NASA Technical Reports Server (NTRS)

Smith, Eric A.

2002-01-01

During the coming decade, the internationally organized Global Precipitation Measurement (GPM) Mission will take an important step in creating a global precipitation observing system from space based on an international fleet of satellites operated as a constellation. One perspective for understanding the nature of GPM is that it will be a hierarchical system of datastreams beginning with very high caliber combined dual frequency radar/passive microwave (PMW) rain-radiometer retrievals, to high caliber PMW rain-radiometer only retrievals, and then on to blends of the former datastreams with additional lower-caliber PMW-based and IR-based rain retrievals. Within the context of the now emerging global water & energy cycle (GWEC) programs of a number of research agencies throughout the world, GPM serves as a centerpiece space mission for improving our understanding of the Earth's water cycle from a global measurement perspective and on down to regional scales and below. One of the salient problems within our current understanding of the global water and energy cycle is determining whether a change in the rate of the water cycle is accompanying changes in climate, e.g., climate warming. As there are a number of ways in which to define a rate-change of the global water cycle, it is not entirely clear as to what constitutes such a determination. This paper first presents an overview of the GPM Mission and how its overriding scientific objectives for climate, weather, and hydrology flow from the anticipated improvements that are being planned for the constellation-based measuring system. Next, the paper shows how the GPM observations can be used within the framework of the oceanic and continental water budget equations to determine whether a given perturbation in precipitation is indicative of an actual rate change in the water cycle, consistent with required responses in water storage and/or water flux transport processes, or whether it is simply part of the natural variability of a fixed rate cycle.

75 FR 69032 - Naval Surface Warfare Center, Potomac River, Dahlgren, VA; Danger Zone

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-10

... hazardous operations such as firing large and small caliber guns and projectiles, aerial bombing, use of... protect the public from hazardous operations such as firing large and small caliber guns and projectiles... zone to include firing of large or small caliber guns and projectiles, aerial bombing, use of directed...

Caliber Schools. Caliber: Beta Academy

ERIC Educational Resources Information Center

EDUCAUSE, 2015

2015-01-01

Caliber: Beta Academy is reimagining education as we know it, with the belief that the innovations in its model will allow 100% of its students to graduate ready to attend and succeed in a competitive four-year college and beyond. The academic model of the school features personalized learning plans, blended learning for English and math,…

Enhanced Mechanical Properties of 316L Stainless Steel Prepared by Aluminothermic Reaction Subjected to Multiple Warm Rolling

NASA Astrophysics Data System (ADS)

Li, Z. N.; Wei, F. A.; La, P. Q.; Ma, F. L.

2018-05-01

Large dimensional bulk 316L stainless steels were prepared by aluminothermic reaction method and rolled at 973 K (700 °C) with different deformation, the microstructures evolution and mechanical properties were characterized in detail. The results showed that the microstructure of casting steel consists of nanocrystalline/submicrocrystalline/microcrystalline austenite and submicrocrystalline ferrite. After rolling to thickness reduction of 30, 50 and 70%, the submicrocrystalline austenite grains were crushed and dispersed more uniformly in the matrix of the steel, the grain size of submicrocrystalline austenite decreased from 246 to 136 nm. The mechanical properties of the rolled steels were significantly enhanced, with the thickness reduction increased from 30 to 70%, the tensile strength increased from 632 to 824 MPa, the yield strength increased from 425 to 615 MPa, and the elongation increased from 11 to 24%. After rolling to thickness reduction of 70%, the optimized combination of high strength and high ductility was obtained.

An investigation to determine the pressure distribution on the 0.0137 scale solid rocket booster forebody (MSFC model 467) at angles of attack at or near 90 deg and high Reynolds numbers in the MSFC High Reynolds Number Wind Tunnel (SA29F)

NASA Technical Reports Server (NTRS)

Ramsey, P. E.

1976-01-01

An aerodynamic investigation was conducted in the MSFC High Reynolds Number Wind Tunnel to determine the pressure distribution over the foresection of the current 146 inch diameter shuttle SRB. The test model consisted of a 0.0137 scale version of the SRB nose cone and a forward portion of the cylindrical body which was approximately 2.7 calibers in length. The pressure distributions are plotted as a function of longitudinal station ratioed to body diameter and circumferential location for each angle of attack and Mach number. A Reynolds number variation study was made for Mach numbers of 0.4 and 0.6 at an angle of attack of 270 deg and roll angle of 180 deg.

Recrystallization kinetics of warm-rolled tungsten in the temperature range 1150-1350 °C

NASA Astrophysics Data System (ADS)

Alfonso, A.; Juul Jensen, D.; Luo, G.-N.; Pantleon, W.

2014-12-01

Pure tungsten is a potential candidate material for the plasma-facing first wall and the divertor of fusion reactors. Both parts have to withstand high temperatures during service. This will alter the microstructure of the material by recovery, recrystallization and grain growth and will cause degradation in material properties as a loss in mechanical strength and embrittlement. The thermal stability of a pure tungsten plate warm-rolled to 67% thickness reduction was investigated by long-term isothermal annealing in the temperature range between 1150 °C and 1350 °C up to 2200 h. Changes in the mechanical properties during annealing are quantified by Vickers hardness measurements. They are described concisely by classical kinetic models for recovery and recrystallization. The observed time spans for recrystallization and the obtained value for the activation energy of the recrystallization process indicate a sufficient thermal stability of the tungsten plate during operation below 1075 °C.

The extremely narrow-caliber esophagus is a treatment-resistant subphenotype of eosinophilic esophagitis.

PubMed

Eluri, Swathi; Runge, Thomas M; Cotton, Cary C; Burk, Caitlin M; Wolf, W Asher; Woosley, John T; Shaheen, Nicholas J; Dellon, Evan S

2016-06-01

Some patients with eosinophilic esophagitis (EoE) have an extremely narrow esophagus, but the characteristics of this group have not been extensively described. We aimed to characterize the narrow-caliber phenotype of EoE, determine associated risk factors, and identify differences in treatment response in this subgroup of patients. This retrospective cohort study from 2001 to 2014 included subjects with a new diagnosis of EoE per consensus guidelines. Demographic, endoscopic, histologic, and treatment response data were extracted from medical records. An extremely narrow-caliber esophagus was defined when a neonatal endoscope was required to traverse the esophagus due to the inability to pass an adult endoscope. Patients with and without an extremely narrow-caliber esophagus were compared. Multivariable logistical regression was performed to assess treatment outcomes. Of 513 patients with EoE, 46 (9%) had an extremely narrow-caliber esophagus. These patients were older (33 vs 22 years; P < .01), had longer symptom duration (11 vs 3 years; P < .01), more dysphagia (98% vs 66%; P < .01), and food impactions (53% vs 31%; P < .01). Dilation was more common with extreme narrowing (69% vs 17%; P < .01). Patients with a narrow-caliber esophagus were more refractory to steroid treatment, with lower symptom (56% vs 85%), endoscopic (52% vs 76%), and histologic (33% vs 63%) responses (P < .01 for all), and these differences persisted after multivariate analysis. The extremely narrow-caliber esophagus is a more treatment-resistant subphenotype of EoE and is characterized by longer symptom duration and the need for multiple dilations. Recognition of an extremely narrow-caliber esophagus at diagnosis of EoE can provide important prognostic information. Copyright © 2016 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Limited tolerance by insects to high temperatures across tropical elevational gradients and the implications of global warming for extinction.

PubMed

García-Robledo, Carlos; Kuprewicz, Erin K; Staines, Charles L; Erwin, Terry L; Kress, W John

2016-01-19

The critical thermal maximum (CTmax), the temperature at which motor control is lost in animals, has the potential to determine if species will tolerate global warming. For insects, tolerance to high temperatures decreases with latitude, suggesting that similar patterns may exist along elevational gradients as well. This study explored how CTmax varies among species and populations of a group of diverse tropical insect herbivores, the rolled-leaf beetles, across both broad and narrow elevational gradients. Data from 6,948 field observations and 8,700 museum specimens were used to map the elevational distributions of rolled-leaf beetles on two mountains in Costa Rica. CTmax was determined for 1,252 individual beetles representing all populations across the gradients. Initial morphological identifications suggested a total of 26 species with populations at different elevations displaying contrasting upper thermal limits. However, compared with morphological identifications, DNA barcodes (cytochrome oxidase I) revealed significant cryptic species diversity. DNA barcodes identified 42 species and haplotypes across 11 species complexes. These 42 species displayed much narrower elevational distributions and values of CTmax than the 26 morphologically defined species. In general, species found at middle elevations and on mountaintops are less tolerant to high temperatures than species restricted to lowland habitats. Species with broad elevational distributions display high CTmax throughout their ranges. We found no significant phylogenetic signal in CTmax, geography, or elevational range. The narrow variance in CTmax values for most rolled-leaf beetles, especially high-elevation species, suggests that the risk of extinction of insects may be substantial under some projected rates of global warming.

Limited tolerance by insects to high temperatures across tropical elevational gradients and the implications of global warming for extinction

PubMed Central

García-Robledo, Carlos; Kuprewicz, Erin K.; Staines, Charles L.; Erwin, Terry L.; Kress, W. John

2016-01-01

The critical thermal maximum (CTmax), the temperature at which motor control is lost in animals, has the potential to determine if species will tolerate global warming. For insects, tolerance to high temperatures decreases with latitude, suggesting that similar patterns may exist along elevational gradients as well. This study explored how CTmax varies among species and populations of a group of diverse tropical insect herbivores, the rolled-leaf beetles, across both broad and narrow elevational gradients. Data from 6,948 field observations and 8,700 museum specimens were used to map the elevational distributions of rolled-leaf beetles on two mountains in Costa Rica. CTmax was determined for 1,252 individual beetles representing all populations across the gradients. Initial morphological identifications suggested a total of 26 species with populations at different elevations displaying contrasting upper thermal limits. However, compared with morphological identifications, DNA barcodes (cytochrome oxidase I) revealed significant cryptic species diversity. DNA barcodes identified 42 species and haplotypes across 11 species complexes. These 42 species displayed much narrower elevational distributions and values of CTmax than the 26 morphologically defined species. In general, species found at middle elevations and on mountaintops are less tolerant to high temperatures than species restricted to lowland habitats. Species with broad elevational distributions display high CTmax throughout their ranges. We found no significant phylogenetic signal in CTmax, geography, or elevational range. The narrow variance in CTmax values for most rolled-leaf beetles, especially high-elevation species, suggests that the risk of extinction of insects may be substantial under some projected rates of global warming. PMID:26729867

Obesity and the Microvasculature: A Systematic Review and Meta-Analysis

PubMed Central

Boillot, Adrien; Zoungas, Sophia; Mitchell, Paul; Klein, Ronald; Klein, Barbara; Ikram, Mohammad Kamran; Klaver, Caroline; Wang, Jie Jin; Gopinath, Bamini; Tai, E. Shyong; Neubauer, Aljoscha Steffen; Hercberg, Serge; Brazionis, Laima; Saw, Seang-Mei; Wong, Tien-Yin; Czernichow, Sébastien

2013-01-01

Background Overweight and obesity are thought to significantly influence a person's risk of cardiovascular disease, possibly via its effect on the microvasculature. Retinal vascular caliber is a surrogate marker of microvascular disease and a predictor of cardiovascular events. The aim of this systematic review and meta-analysis was to determine the association between body mass index (BMI) and retinal vascular caliber. Methods and Findings Relevant studies were identified by searches of the MEDLINE and EMBASE databases from 1966 to August 2011. Standardized forms were used for data extraction. Among over 44,000 individuals, obese subjects had narrower arteriolar and wider venular calibers when compared with normal weight subjects, independent of conventional cardiovascular risk factors. In adults, a 1 kg/m2 increase in BMI was associated with a difference of 0.07 μm [95% CI: −0.08; −0.06] in arteriolar caliber and 0.22 μm [95% CI: 0.21; 0.23] in venular caliber. Similar results were found for children. Conclusions Higher BMI is associated with narrower retinal arteriolar and wider venular calibers. Further prospective studies are needed to examine whether a causative relationship between BMI and retinal microcirculation exists. PMID:23405065

Raman spectroscopic analysis of gunshot residue offering great potential for caliber differentiation.

PubMed

Bueno, Justin; Sikirzhytski, Vitali; Lednev, Igor K

2012-05-15

Near-infrared (NIR) Raman microspectroscopy combined with advanced statistics was used to differentiate gunshot residue (GSR) particles originating from different caliber ammunition. The firearm discharge process is analogous to a complex chemical reaction. The reagents of this process are represented by the chemical composition of the ammunition, firearm, and cartridge case. The specific firearm parameters determine the conditions of the reaction and thus the subsequent product, GSR. We found that Raman spectra collected from these products are characteristic for different caliber ammunition. GSR particles from 9 mm and 0.38 caliber ammunition, collected under identical discharge conditions, were used to demonstrate the capability of confocal Raman microspectroscopy for the discrimination and identification of GSR particles. The caliber differentiation algorithm is based on support vector machines (SVM) and partial least squares (PLS) discriminant analyses, validated by a leave-one-out cross-validation method. This study demonstrates for the first time that NIR Raman microspectroscopy has the potential for the reagentless differentiation of GSR based upon forensically relevant parameters, such as caliber size. When fully developed, this method should have a significant impact on the efficiency of crime scene investigations.

Strong, non-magnetic, cube textured alloy substrates

DOEpatents

Goyal, Amit [Knoxville, TN

2011-02-01

A warm-rolled, annealed, polycrystalline, cube-textured, {100}<100>, FCC-based alloy substrate is characterized by a yield strength greater than 200 MPa and a biaxial texture characterized by a FWHM of less than 15.degree. in all directions.

Tachyon warm inflation with the effects of loop quantum cosmology in the light of Planck 2015

NASA Astrophysics Data System (ADS)

Kamali, Vahid; Basilakos, Spyros; Mehrabi, Ahmad; Motaharfar, Meysam; Massaeli, Erfan

We investigate the observational signatures of quantum cosmology in the Cosmic Microwave Background data provided by Planck collaboration. We apply the warm inflationary paradigm with a tachyon scalar field to the loop quantum cosmology. In this context, we first provide the basic cosmological functions in terms of the tachyon field. We then obtain the slow-roll parameters and the power spectrum of scalar and tensor fluctuations, respectively. Finally, we study the performance of various warm inflationary scenarios against the latest Planck data and we find a family of models which are in agreement with the observations.

Tachyon warm-intermediate inflationary universe model in high dissipative regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Setare, M.R.; Kamali, V., E-mail: rezakord@ipm.ir, E-mail: vkamali1362@gmail.com

2012-08-01

We consider tachyonic warm-inflationary models in the context of intermediate inflation. We derive the characteristics of this model in slow-roll approximation and develop our model in two cases, 1- For a constant dissipative parameter Γ. 2- Γ as a function of tachyon field φ. We also describe scalar and tensor perturbations for this scenario. The parameters appearing in our model are constrained by recent observational data. We find that the level of non-Gaussianity for this model is comparable with non-tachyonic model.

Assessing the Causality between Blood Pressure and Retinal Vascular Caliber through Mendelian Randomisation

NASA Astrophysics Data System (ADS)

Li, Ling-Jun; Liao, Jiemin; Cheung, Carol Yim-Lui; Ikram, M. Kamran; Shyong, Tai E.; Wong, Tien-Yin; Cheng, Ching-Yu

2016-02-01

We aimed to determine the association between blood pressure (BP) and retinal vascular caliber changes that were free from confounders and reverse causation by using Mendelian randomisation. A total of 6528 participants from a multi-ethnic cohort (Chinese, Malays, and Indians) in Singapore were included in this study. Retinal arteriolar and venular caliber was measured by a semi-automated computer program. Genotyping was done using Illumina 610-quad chips. Meta-analysis of association between BP, and retinal arteriolar and venular caliber across three ethnic groups was performed both in conventional linear regression and Mendelian randomisation framework with a genetic risk score of BP as an instrumental variable. In multiple linear regression models, each 10 mm Hg increase in systolic BP, diastolic BP, and mean arterial BP (MAP) was associated with significant decreases in retinal arteriolar caliber of a 1.4, 3.0, and 2.6 μm, and significant decreases in retinal venular caliber of a 0.6, 0.7, and 0.9 μm, respectively. In a Mendelian randomisation model, only associations between DBP and MAP and retinal arteriolar narrowing remained yet its significance was greatly reduced. Our data showed weak evidence of a causal relationship between elevated BP and retinal arteriolar narrowing.

Effect of Grain Orientation and Boundary Distributions on Hydrogen-Induced Cracking in Low-Carbon-Content Steels

NASA Astrophysics Data System (ADS)

Masoumi, Mohammad; Coelho, Hana Livia Frota; Tavares, Sérgio Souto Maior; Silva, Cleiton Carvalho; de Abreu, Hamilton Ferreira Gomes

2017-08-01

Hydrogen-induced cracking (HIC) causes considerable economic losses in a wide range of steels exposed to corrosive environments. The effect of crystallographic texture and grain boundary distributions tailored by rolling at 850 °C in three different steels with a body-centered cube structure was investigated on HIC resistance. The x-ray and electron backscattered diffraction techniques were used to characterize texture evolutions during the rolling process. The findings revealed a significant improvement against HIC based on texture engineering. In addition, increasing the number of {111} and {110} grains, associated with minimizing the number of {001} grains in warm-rolled samples, reduced HIC susceptibility. Moreover, the results showed that boundaries associated with low {hkl} indexing and denser packing planes had more resistance against crack propagation.

Methods to Reduce Sand Ejecta from Projectile Impact - a Scaled Study with the Goal of Application to Depleted Uranium Penetrator Catch Boxes

DTIC Science & Technology

2012-04-01

caliber ammunition that were commercially available were used in this study: (1) lead ball (M33 ball) and (2) armor piercing ( machine hardened steel, M2 ...each test fire. The barrel will be a machined 0.50 caliber, 1 in 15-inch right twist bore, 29-inch length barrel without a muzzle brake; muzzle brake...11 Figure 15. Fired M2 50-caliber round

Computational Approach to Identify Different Injuries by Firearms.

PubMed

Costa, Sarah Teixeira; Freire, Alexandre Rodrigues; Matoso, Rodrigo Ivo; Daruge Júnior, Eduardo; Rossi, Ana Cláudia; Prado, Felippe Bevilacqua

2017-03-01

Complications arise in the analysis of gunshot wounds to the maxillofacial region, when neither the projectile nor the gun is found at the crime scene. We simulated 5- and 15-cm firing distances at a human mandible to investigate the external morphology of entrance wounds based on fire range. The ammunition models, .40-caliber S&W, .380-caliber, and 9 × 19-mm Luger, were constructed with free-form NURBS surfaces. In a dynamic simulation, projectiles were fired against mandibular body 3D model at 5 and 15 cm. All entrance wounds presented oval aspect. Maximum diameter and von Mises stress values were 16.5 mm and 50.8 MPa, both for .40-caliber S&W fired at 5 cm. The maximum energy loss was 138.4 J for .40 S&W fired at 15 cm. In conclusion, the mandible was most affected by .40-caliber S&W and morphological differences were observable in holes caused by different incoming projectile calibers fired at different distances. © 2017 American Academy of Forensic Sciences.

Implementation of Unsteady Double-Axis of Rotation Motion to Predict Pitch-Damping Moment

DTIC Science & Technology

2016-10-18

2014;51(5). 4. Dupuis A. Aeroballistic range and wind tunnel tests of the basic finner reference projectile from subsonic to high supersonic velocities... modelled . Typically, when computing aerodynamic coefficients, motion about each axis is considered individually (i.e., spin around body-axis, pitch about...has a diameter, , of 0.03 m (1 caliber) and consists of a 10° half- angle cone that is 2.84-calibers long, followed by a 7.16-caliber cylindrical

Unsedated transnasal small-caliber esophagogastroduodenoscopy in elderly and bedridden patients.

PubMed

Yuki, Mika; Amano, Yuji; Komazawa, Yoshinori; Fukuhara, Hiroyuki; Shizuku, Toshihiro; Yamamoto, Shun; Kinoshita, Yoshikazu

2009-11-28

To evaluate the safety of unsedated transnasal small-caliber esophagogastroduodenoscopy (EGD) for elderly and critically ill bedridden patients. One prospective randomized comparative study and one crossover comparative study between transnasal small-caliber EGD and transoral conventional EGD was done (Study 1). For the comparative study, we enrolled 240 elderly patients aged > 65 years old. For the crossover analysis, we enrolled 30 bedridden patients with percutaneous endoscopic gastrostomy (PEG) (Study 2). We evaluated cardiopulmonary effects by measuring arterial oxygen saturation (SpO(2)) and calculating the rate-pressure product (RPP) (pulse rate x systolic blood pressure/100) at baseline, 2 and 5 min after endoscopic intubation in Study 1. To assess the risk for endoscopy-related aspiration pneumonia during EGD, we also measured blood leukocyte counts and serum C-reactive protein (CRP) levels before and 3 d after EGD in Study 2. In Study 1, we observed significant decreases in SpO(2) during conventional transoral EGD, but not during transnasal small-caliber EGD (0.24% vs -0.24% after 2 min, and 0.18% vs -0.29% after 5 min, P = 0.034, P = 0.044). Significant differences of the RPP were not found between conventional transoral and transnasal small-caliber EGD. In Study 2, crossover analysis showed statistically significant increases of the RPP at 2 min after intubation and the end of endoscopy (26.8 and 34.6 vs 3.1 and 15.2, P = 0.044, P = 0.046), and decreases of SpO(2) (-0.8% vs -0.1%, P = 0.042) during EGD with transoral conventional in comparison with transnasal small-caliber endoscopy. Thus, for bedridden patients with PEG feeding, who were examined in the supine position, transoral conventional EGD more severely suppressed cardiopulmonary function than transnasal small-caliber EGD. There were also significant increases in the markers of inflammation, blood leukocyte counts and serum CRP values, in bedridden patients after transoral conventional EGD, but not after transnasal small-caliber EGD performed with the patient in the supine position. Leukocyte count increased from 6053 +/- 1975/L to 6900 +/- 3392/L (P = 0.0008) and CRP values increased from 0.93 +/- 0.24 to 2.49 +/- 0.91 mg/dL (P = 0.0005) at 3 d after transoral conventional EGD. Aspiration pneumonia, possibly caused by the endoscopic examination, was found subsequently in two of 30 patients after transoral conventional EGD. Transnasal small-caliber EGD is a safer method than transoral conventional EGD in critically ill, bedridden patients who are undergoing PEG feeding.

Unsedated transnasal small-caliber esophagogastroduodenoscopy in elderly and bedridden patients

PubMed Central

Yuki, Mika; Amano, Yuji; Komazawa, Yoshinori; Fukuhara, Hiroyuki; Shizuku, Toshihiro; Yamamoto, Shun; Kinoshita, Yoshikazu

2009-01-01

AIM: To evaluate the safety of unsedated transnasal small-caliber esophagogastroduodenoscopy (EGD) for elderly and critically ill bedridden patients. METHODS: One prospective randomized comparative study and one crossover comparative study between transnasal small-caliber EGD and transoral conventional EGD was done (Study 1). For the comparative study, we enrolled 240 elderly patients aged > 65 years old. For the crossover analysis, we enrolled 30 bedridden patients with percutaneous endoscopic gastrostomy (PEG) (Study 2). We evaluated cardiopulmonary effects by measuring arterial oxygen saturation (SpO2) and calculating the rate-pressure product (RPP) (pulse rate × systolic blood pressure/100) at baseline, 2 and 5 min after endoscopic intubation in Study 1. To assess the risk for endoscopy-related aspiration pneumonia during EGD, we also measured blood leukocyte counts and serum C-reactive protein (CRP) levels before and 3 d after EGD in Study 2. RESULTS: In Study 1, we observed significant decreases in SpO2 during conventional transoral EGD, but not during transnasal small-caliber EGD (0.24% vs -0.24% after 2 min, and 0.18% vs -0.29% after 5 min, P = 0.034, P = 0.044). Significant differences of the RPP were not found between conventional transoral and transnasal small-caliber EGD. In Study 2, crossover analysis showed statistically significant increases of the RPP at 2 min after intubation and the end of endoscopy (26.8 and 34.6 vs 3.1 and 15.2, P = 0.044, P = 0.046), and decreases of SpO2 (-0.8% vs -0.1%, P = 0.042) during EGD with transoral conventional in comparison with transnasal small-caliber endoscopy. Thus, for bedridden patients with PEG feeding, who were examined in the supine position, transoral conventional EGD more severely suppressed cardiopulmonary function than transnasal small-caliber EGD. There were also significant increases in the markers of inflammation, blood leukocyte counts and serum CRP values, in bedridden patients after transoral conventional EGD, but not after transnasal small-caliber EGD performed with the patient in the supine position. Leukocyte count increased from 6053 ± 1975/L to 6900 ± 3392/L (P = 0.0008) and CRP values increased from 0.93 ± 0.24 to 2.49 ± 0.91 mg/dL (P = 0.0005) at 3 d after transoral conventional EGD. Aspiration pneumonia, possibly caused by the endoscopic examination, was found subsequently in two of 30 patients after transoral conventional EGD. CONCLUSION: Transnasal small-caliber EGD is a safer method than transoral conventional EGD in critically ill, bedridden patients who are undergoing PEG feeding. PMID:19938199

Examination of Ricochet Gunshot Wounds From Commonly Encountered Surfaces.

PubMed

Hlavaty, Leigh; Avedschmidt, Sarah; Root, Kelly; Amley, Jeffrey; Sung, LokMan

2016-12-01

Proper interpretation of gunshot wounds is vital for the forensic pathologist and requires experience and expertise, as well as consultation with a firearms and ballistics expert and careful scene investigation in cases of atypical gunshot wounds. This study is the first large-series examining ricochet gunshot wounds involving different firearm calibers. Typical gunshot wounds created from 4 handgun calibers (22 Long Rifle, 9 × 19 mm Parabellum, .40 Smith &Wesson, and .45 Automatic Colt Pistol) and 2 rifle calibers (5.56 and 7.62 mm) were compared with wounds caused by bullets of those same calibers ricocheting off commonly encountered surfaces (concrete, asphalt, aluminum traffic signs, clay brick, and dry wall). Porcine skin, a human skin analog, attached to sheets of cardboard serviced as witness panels for capturing the entrance wounds. Examination of over 150 handgun and rifle entrance wounds established that every caliber and every ricochet surface resulted in atypical features, including irregularity in size or shape, lack of marginal abrasion, or other injuries on the surrounding skin. The most significant factor influencing the variability of the ricochet wounds was the surface the bullet deflected off before striking the body.

In the Hot Seat--Analyzing Your Heating Options

ERIC Educational Resources Information Center

Palliser, Janna

2011-01-01

When winter rolls around, keeping yourself and your home warm is of the utmost importance. Heating your home seems like a simple subject to tackle, but there are many heating systems available, requiring different fuels, installations, and costs. The various fuel types and their environmental footprints will be the focus of this month's column.…

Effect of pre-strain on creep of three AISI 316 austenitic stainless steels in relation to reheat cracking of weld-affected zones

NASA Astrophysics Data System (ADS)

Auzoux, Q.; Allais, L.; Caës, C.; Monnet, I.; Gourgues, A. F.; Pineau, A.

2010-05-01

Microstructural modifications induced by welding of 316 stainless steels and their effect on creep properties and relaxation crack propagation were examined. Cumulative strain due to multi-pass welding hardens the materials by increasing the dislocation density. Creep tests were conducted on three plates from different grades of 316 steel at 600 °C, with various carbon and nitrogen contents. These plates were tested both in the annealed condition and after warm rolling, which introduced pre-strain. It was found that the creep strain rate and ductility after warm rolling was reduced compared with the annealed condition. Moreover, all steels exhibited intergranular crack propagation during relaxation tests on Compact Tension specimens in the pre-strained state, but not in the annealed state. These results confirmed that the reheat cracking risk increases with both residual stress triaxiality and pre-strain. On the contrary, high solute content and strain-induced carbide precipitation, which are thought to increase reheat cracking risk of stabilised austenitic stainless steels did not appear as key parameters in reheat cracking of 316 stainless steels.

Fluid-structure interaction of a rolling restrained body of revolution at high angles of attack

NASA Astrophysics Data System (ADS)

Degani, D.; Ishay, M.; Gottlieb, O.

2017-03-01

The current work investigates numerically rolling instabilities of a free-to-roll slender rigid-body of revolution placed in a wind tunnel at a high angle of attack. The resistance to the roll moment is represented by a linear torsion spring and equivalent linear damping representing friction in the bearings of a simulated wind tunnel model. The body is subjected to a three-dimensional, compressible, laminar flow. The full Navier-Stokes equations are solved using the second-order implicit finite difference Beam-Warming scheme, adapted to a curvilinear coordinate system, whereas the coupled structural second order equation of motion for roll is solved by a fourth-order Runge-Kutta method. The body consists of a 3.5-diameter tangent ogive forebody with a 7.0-diameter long cylindrical afterbody extending aft of the nose-body junction to x/D = 10.5. We describe in detail the investigation of three angles of attack 20°, 40°, and 65°, at a Reynolds number of 30 000 (based on body diameter) and a Mach number of 0.2. Three distinct configurations are investigated as follows: a fixed body, a free-to-roll body with a weak torsion spring, and a free-to-roll body with a strong torsion spring. For each angle of attack the free-to-roll configuration portrays a distinct and different behavior pattern, including bi-stable limit-cycle oscillations. The bifurcation structure incorporates both large and small amplitude periodic roll oscillations where the latter lose their periodicity with increasing stiffness of the restraining spring culminating with distinct quasiperiodic oscillations. We note that removal of an applied upstream disturbance for a restrained body does not change the magnitude or complexity of the oscillations or of the flow patterns along the body. Depending on structure characteristics and flow conditions even a small rolling moment coefficient at the relatively low angle of attack of 20° may lead to large amplitude resonant roll oscillations.

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel

PubMed Central

Zhao, Xianming; Shen, Yongfeng; Qiu, Lina; Liu, Yandong; Sun, Xin; Zuo, Liang

2014-01-01

A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity) concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.%) steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits a yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10−3/s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase) and ultrafine austenite lamellae (50–200 nm, strong and ductile phase) is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C. PMID:28788282

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel.

PubMed

Zhao, Xianming; Shen, Yongfeng; Qiu, Lina; Liu, Yandong; Sun, Xin; Zuo, Liang

2014-12-09

A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity) concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.%) steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits a yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10 -3 /s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase) and ultrafine austenite lamellae (50-200 nm, strong and ductile phase) is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C.

Anatomical Assessment of the Temporopolar Artery for Revascularization of Deep Recipients.

PubMed

Tayebi Meybodi, Ali; Benet, Arnau; Griswold, Dylan; Dones, Flavia; Preul, Mark C; Lawton, Michael T

2018-05-30

Intracranial-intracranial and extracranial-intracranial bypass options for revascularization of deep cerebral recipients are limited and technically demanding. To assess the anatomical feasibility of using the temporopolar artery (TPA) for revascularization of the anterior cerebral artery (ACA), posterior cerebral artery (PCA), and superior cerebellar arteries (SCA). Orbitozygomatic craniotomy was performed bilaterally on 8 cadaveric heads. The cisternal segment of the TPA was dissected. The TPA was cut at M3-M4 junction with its proximal and distal calibers and the length of the cisternal segment measured. Feasibility of the TPA-A1-ACA, TPA-A2-ACA, TPA-SCA, and TPA-PCA bypasses were assessed. A total of 17 TPAs were identified in 16 specimens. The average distal TPA caliber was 1.0 ± 0.2 mm, and the average cisternal length was 37.5 ± 9.4 mm. TPA caliber was ≥ 1.0 mm in 12 specimens (70%). The TPA-A1-ACA bypass was feasible in all specimens, whereas the TPA reached the A2-ACA, SCA, and PCA in 94% of specimens (16/17). At the point of anastomosis, the average recipient caliber was 2.5 ± 0.5 mm for A1-ACA, and 2.3 ± 0.7 mm for A2-ACA. The calibers of the SCA and PCA at the anastomosis points were 2.0 ± 0.6 mm, and 2.7 ± 0.8 mm, respectively. The TPA-ACA, TPA-PCA, and TPA-SCA bypasses are anatomically feasible and may be used when the distal caliber of the TPA stump is optimal to provide adequate blood flow. This study lays foundations for clinical use of the TPA for ACA revascularization in well-selected cases.

Total Human Eye Allotransplantation: Developing Surgical Protocols for Donor and Recipient Procedures

PubMed Central

Davidson, Edward H.; Wang, Eric W.; Yu, Jenny Y.; Fernandez-Miranda, Juan C.; Wang, Dawn J.; Richards, Nikisha; Miller, Maxine; Schuman, Joel S.; Washington, Kia M.

2017-01-01

Background Vascularized composite allotransplantation of the eye is an appealing, novel method for reconstruction of the nonfunctioning eye. The authors’ group has established the first orthotopic model for eye transplantation in the rat. With advancements in immunomodulation strategies together with new therapies in neuroregeneration, parallel development of human surgical protocols is vital for ensuring momentum toward eye transplantation in actual patients. Methods Cadaveric donor tissue harvest (n = 8) was performed with orbital exenteration, combined open craniotomy, and endonasal approach to ligate the ophthalmic artery with a cuff of paraclival internal carotid artery, for transection of the optic nerve at the optic chiasm and transection of cranial nerves III to VI and the superior ophthalmic vein at the cavernous sinus. Candidate recipient vessels (superficial temporal/internal maxillary/facial artery and superficial temporal/facial vein) were exposed. Vein grafts were required for all anastomoses. Donor tissue was secured in recipient orbits followed by sequential venous and arterial anastomoses and nerve coaptation. Pedicle lengths and calibers were measured. All steps were timed, photographed, video recorded, and critically analyzed after each operative session. Results The technical feasibility of cadaveric donor procurement and transplantation to cadaveric recipient was established. Mean measurements included optic nerve length (39 mm) and caliber (5 mm), donor artery length (33 mm) and caliber (3 mm), and superior ophthalmic vein length (15 mm) and caliber (0.5 mm). Recipient superficial temporal, internal maxillary artery, and facial artery calibers were 0.8, 2, and 2 mm, respectively; and superior temporal and facial vein calibers were 0.8 and 2.5 mm, respectively. Conclusion This surgical protocol serves as a benchmark for optimization of technique, large-animal model development, and ultimately potentiating the possibility of vision restoration transplantation surgery. PMID:27879599

Advanced automobile steels subjected to plate rolling at 773 K or 1373 K

NASA Astrophysics Data System (ADS)

Torganchuk, Vladimir; Belyakov, Andrey; Kaibyshev, Rustam

2017-12-01

The high manganese steels exhibiting the effects of twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP) demonstrate an excellent combination of enhanced formability, strength and ductility. Such unique mechanical properties make high-manganese steel the most attractive material for various applications, including the segment of advanced automobile steels. The strain hardening in such steels can be achieved through martensitic transformation, when the stacking fault energy (SFE) is about 10 mJ m-2, and/or twinning, when SFE is about 20 to 50 mJ m-2. The actual mechanical properties of high-Mn steels could vary, depending on the conditions of thermo-mechanical processing. In the present study, the effect of rolling temperature on the microstructure and mechanical properties of 18% Mn steels was clarified. The steels hot rolled at 1373 K were characterized by uniform almost equiaxed grains with near random crystallographic orientations that resulted in relatively low yield strengths of 300-360 MPa, followed by pronounced strain hardening that led to the total elongation above 60%. In contrast, the steels warm rolled at 773 K were characterized by flattened grains with a strong rolling texture and high yield strengths of 850-950 MPa combined with a total elongation of about 30%.

Axonal Transport: How High Microtubule Density Can Compensate for Boundary Effects in Small-Caliber Axons

PubMed Central

Wortman, Juliana C.; Shrestha, Uttam M.; Barry, Devin M.; Garcia, Michael L.; Gross, Steven P.; Yu, Clare C.

2014-01-01

Long-distance intracellular axonal transport is predominantly microtubule-based, and its impairment is linked to neurodegeneration. In this study, we present theoretical arguments that suggest that near the axon boundaries (walls), the effective viscosity can become large enough to impede cargo transport in small (but not large) caliber axons. Our theoretical analysis suggests that this opposition to motion increases rapidly as the cargo approaches the wall. We find that having parallel microtubules close enough together to enable a cargo to simultaneously engage motors on more than one microtubule dramatically enhances motor activity, and thus minimizes the effects of any opposition to transport. Even if microtubules are randomly placed in axons, we find that the higher density of microtubules found in small-caliber axons increases the probability of having parallel microtubules close enough that they can be used simultaneously by motors on a cargo. The boundary effect is not a factor in transport in large-caliber axons where the microtubule density is lower. PMID:24559984

Influence of warm rolling temperature on ferrite recrystallization in low C and IF steels

NASA Astrophysics Data System (ADS)

Barnett, Matthew Robert

Experiments involving single pass laboratory rolling and isothermal salt bath annealing were carried out; three steels were studied: a titanium stabilized interstitial free grade and two low carbon grades, one of which contained a particularly low level of manganese (˜0.009wt.%). The two low carbon grades were produced such that any complication from AlN precipitation was avoided. X-ray, neutron diffraction, optical metallography and mechanical testing measurements were carried out on the samples before and after annealing. The main aim of this work was to further the understanding of the metallurgy of recrystallization after ferrite rolling at temperatures between room temperature and 700sp°C. Deformation textures, recrystallization kinetics, final grain sizes and recrystallization textures were quantified for all the samples and experimental conditions. A major conclusion based on these data is that the influence of rolling temperature is far greater in the low carbon samples than in the IF grade. Indeed, the IF results alter only marginally with increasing temperature. In the low carbon grades, however, the rolling texture sharpens, recrystallization slows, the final grain size coarsens, and the recrystallization texture changes when the rolling temperature is increased. This distinct difference between the two steel types is explained in terms of their contrasting deformation behaviors. Solute carbon and nitrogen in the low carbon grades interact with dislocations causing high stored energy levels after low temperature rolling (due to dynamic strain aging) and high strain rate sensitivities during high temperature rolling (due to the solute drag of dislocations in the transition region between DSA and DRC). Nucleation during subsequent recrystallization is strongly influenced by both the stored energy and the strain rate sensitivity. The latter affects the occurrence of the flow localisations that enhance nucleation.

Program CALIB. [for computing noise levels for helicopter version of S-191 filter wheel spectrometer

NASA Technical Reports Server (NTRS)

Mendlowitz, M. A.

1973-01-01

The program CALIB, which was written to compute noise levels and average signal levels of aperture radiance for the helicopter version of the S-191 filter wheel spectrometer is described. The program functions, and input description are included along with a compiled program listing.

Hamilton-Jacobi formalism to warm inflationary scenario

NASA Astrophysics Data System (ADS)

Sayar, K.; Mohammadi, A.; Akhtari, L.; Saaidi, Kh.

2017-01-01

The Hamilton-Jacobi formalism as a powerful method is being utilized to reconsider the warm inflationary scenario, where the scalar field as the main component driving inflation interacts with other fields. Separating the context into strong and weak dissipative regimes, the goal is followed for two popular functions of Γ . Applying slow-rolling approximation, the required perturbation parameters are extracted and, by comparing to the latest Planck data, the free parameters are restricted. The possibility of producing an acceptable inflation is studied where the result shows that for all cases the model could successfully suggest the amplitude of scalar perturbation, scalar spectral index, its running, and the tensor-to-scalar ratio.

49 CFR Appendix A to Part 223 - Certification of Glazing Materials

Code of Federal Regulations, 2010 CFR

2010-10-01

...-ups, test measuring devices, and test procedures were performed by qualified personnel using... following tests: (i) Ballistic Impact in which a standard 22 caliber long rifle lead bullet of 40 grains in... Impact in which a standard 22 caliber long rifle lead bullet of 40 grains in weight impacts at a minimum...

Effects of Intercritical Annealing Temperature on Mechanical Properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C Steel

DOE PAGES

Zhao, Xianming; Shen, Yongfeng; Qiu, Lina; ...

2014-12-09

A medium Mn steel has been designed to achieve an excellent combination of strength and ductility based on the TRIP (Transformation Induced Plasticity) concept for automotive applications. Following six passes of hot rolling at 850 °C, the Fe-7.9Mn-0.14Si-0.05Al-0.07C (wt.%) steel was warm-rolled at 630 °C for seven passes and subsequently air cooled to room temperature. The sample was subsequently intercritically annealed at various temperatures for 30 min to promote the reverse transformation of martensite into austenite. The obtained results show that the highest volume fraction of austenite is 39% for the sample annealed at 600 °C. This specimen exhibits amore » yield stress of 910 MPa and a high ultimate tensile stress of 1600 MPa, with an elongation-to-failure of 0.29 at a strain rate of 1 × 10⁻³/s. The enhanced work-hardening ability of the investigated steel is closely related to martensitic transformation and the interaction of dislocations. Especially, the alternate arrangement of acicular ferrite (soft phase) and ultrafine austenite lamellae (50–200 nm, strong and ductile phase) is the key factor contributing to the excellent combination of strength and ductility. On the other hand, the as-warm-rolled sample also exhibits the excellent combination of strength and ductility, with elongation-to-failure much higher than those annealed at temperatures above 630 °C.« less

Suicide, guns, and buyback programs: An epidemiologic analysis of firearm-related deaths in Connecticut.

PubMed

Baumann, Laura; Clinton, Heather; Berntsson, Rob; Williams, Susan S; Rovella, James C; Shapiro, David; Thaker, Shefali; Borrup, Kevin; Lapidus, Garry; Campbell, Brendan T

2017-12-01

Gun buyback programs aim to remove unwanted firearms from the community with the goal of preventing firearm injury and death. Buyback programs are held in many communities, but evidence demonstrating their effectiveness is lacking. The purpose of this study is to compare firearms collected at buyback events to crime guns and firearms used in homicides and suicides. Detailed firearm and case data were obtained from the Hartford Police Department and the Office of the Chief Medical Examiner from January through December of 2015. Information was reviewed for guns collected at buyback events, crime guns confiscated by police, and for weapons associated with firearm fatalities. Detailed firearm data included type, manufacturer, model, and caliber (small, ≤ 0.32 caliber; medium, 0.357 caliber to 9 mm; large, ≥ 0.40 caliber). χ analyses were used for comparisons between groups. In 2015, 224 crime guns were seized by the Hartford Police, 169 guns were collected at four community buyback events, and there were 187 firearm-related deaths statewide (105 suicides, 81 homicides, 1 legal intervention). Comparisons between buyback, crime, and fatality-related firearms are shown in the table below. Medium caliber handguns account for the majority of crime guns and fatalities, and buyback programs collected smaller caliber handguns. The demographics of individuals who turn in guns at buyback events and commit suicide are similar: age (buyback, 63 ± 11; suicide, 52 ± 18; homicide, 34 ± 12 years), sex (buyback, 81%; suicide, 91%; homicide, 84% men), and race (buyback, 80%; suicide, 97%; homicide, 47% white). Handguns account for the majority of crime guns and firearm-related fatalities in Connecticut. Buyback programs are both an opportunity to remove unwanted handguns from the community and to remove firearms from the homes of individuals at increased risk of suicide. Epidemiologic/therapeutic study, level IV.

On-Demand Calibration and Evaluation for Electromagnetically Tracked Laparoscope in Augmented Reality Visualization

PubMed Central

Liu, Xinyang; Plishker, William; Zaki, George; Kang, Sukryool; Kane, Timothy D.; Shekhar, Raj

2017-01-01

Purpose Common camera calibration methods employed in current laparoscopic augmented reality systems require the acquisition of multiple images of an entire checkerboard pattern from various poses. This lengthy procedure prevents performing laparoscope calibration in the operating room (OR). The purpose of this work was to develop a fast calibration method for electromagnetically (EM) tracked laparoscopes, such that calibration can be performed in the OR on demand. Methods We designed a mechanical tracking mount to uniquely and snugly position an EM sensor to an appropriate location on a conventional laparoscope. A tool named fCalib was developed to calibrate intrinsic camera parameters, distortion coefficients, and extrinsic parameters (transformation between the scope lens coordinate system and the EM sensor coordinate system) using a single image that shows an arbitrary portion of a special target pattern. For quick evaluation of calibration result in the OR, we integrated a tube phantom with fCalib and overlaid a virtual representation of the tube on the live video scene. Results We compared spatial target registration error between the common OpenCV method and the fCalib method in a laboratory setting. In addition, we compared the calibration re-projection error between the EM tracking-based fCalib and the optical tracking-based fCalib in a clinical setting. Our results suggested that the proposed method is comparable to the OpenCV method. However, changing the environment, e.g., inserting or removing surgical tools, would affect re-projection accuracy for the EM tracking-based approach. Computational time of the fCalib method averaged 14.0 s (range 3.5 s – 22.7 s). Conclusions We developed and validated a prototype for fast calibration and evaluation of EM tracked conventional (forward viewing) laparoscopes. The calibration method achieved acceptable accuracy and was relatively fast and easy to be performed in the OR on demand. PMID:27250853

On-demand calibration and evaluation for electromagnetically tracked laparoscope in augmented reality visualization.

PubMed

Liu, Xinyang; Plishker, William; Zaki, George; Kang, Sukryool; Kane, Timothy D; Shekhar, Raj

2016-06-01

Common camera calibration methods employed in current laparoscopic augmented reality systems require the acquisition of multiple images of an entire checkerboard pattern from various poses. This lengthy procedure prevents performing laparoscope calibration in the operating room (OR). The purpose of this work was to develop a fast calibration method for electromagnetically (EM) tracked laparoscopes, such that the calibration can be performed in the OR on demand. We designed a mechanical tracking mount to uniquely and snugly position an EM sensor to an appropriate location on a conventional laparoscope. A tool named fCalib was developed to calibrate intrinsic camera parameters, distortion coefficients, and extrinsic parameters (transformation between the scope lens coordinate system and the EM sensor coordinate system) using a single image that shows an arbitrary portion of a special target pattern. For quick evaluation of calibration results in the OR, we integrated a tube phantom with fCalib prototype and overlaid a virtual representation of the tube on the live video scene. We compared spatial target registration error between the common OpenCV method and the fCalib method in a laboratory setting. In addition, we compared the calibration re-projection error between the EM tracking-based fCalib and the optical tracking-based fCalib in a clinical setting. Our results suggest that the proposed method is comparable to the OpenCV method. However, changing the environment, e.g., inserting or removing surgical tools, might affect re-projection accuracy for the EM tracking-based approach. Computational time of the fCalib method averaged 14.0 s (range 3.5 s-22.7 s). We developed and validated a prototype for fast calibration and evaluation of EM tracked conventional (forward viewing) laparoscopes. The calibration method achieved acceptable accuracy and was relatively fast and easy to be performed in the OR on demand.

Viscous warm inflation: Hamilton-Jacobi formalism

NASA Astrophysics Data System (ADS)

Akhtari, L.; Mohammadi, A.; Sayar, K.; Saaidi, Kh.

2017-04-01

Using Hamilton-Jacobi formalism, the scenario of warm inflation with viscous pressure is considered. The formalism gives a way of computing the slow-rolling parameter without extra approximation, and it is well-known as a powerful method in cold inflation. The model is studied in detail for three different cases of the dissipation and bulk viscous pressure coefficients. In the first case where both coefficients are taken as constant, it is shown that the case could not portray warm inflationary scenario compatible with observational data even it is possible to restrict the model parameters. For other cases, the results shows that the model could properly predicts the perturbation parameters in which they stay in perfect agreement with Planck data. As a further argument, r -ns and αs -ns are drown that show the acquired result could stand in acceptable area expressing a compatibility with observational data.

Designing the ideal model for assessment of wound contamination after gunshot injuries: a comparative experimental study

PubMed Central

2012-01-01

Background Modern high-velocity projectiles produce temporary cavities and can thus cause extensive tissue destruction along the bullet path. It is still unclear whether gelatin blocks, which are used as a well-accepted tissue simulant, allow the effects of projectiles to be adequately investigated and how these effects are influenced by caliber size. Method Barium titanate particles were distributed throughout a test chamber for an assessment of wound contamination. We fired .22-caliber Magnum bullets first into gelatin blocks and then into porcine hind limbs placed behind the chamber. Two other types of bullets (.222-caliber bullets and 6.5 × 57 mm cartridges) were then shot into porcine hind limbs. Permanent and temporary wound cavities as well as the spatial distribution of barium titanate particles in relation to the bullet path were evaluated radiologically. Results A comparison of the gelatin blocks and hind limbs showed significant differences (p < 0.05) in the mean results for all parameters. There were significant differences between the bullets of different calibers in the depth to which barium titanate particles penetrated the porcine hind limbs. Almost no particles, however, were found at a penetration depth of 10 cm or more. By contrast, gas cavities were detected along the entire bullet path. Conclusion Gelatin is only of limited value for evaluating the path of high-velocity projectiles and the contamination of wounds by exogenous particles. There is a direct relationship between the presence of gas cavities in the tissue along the bullet path and caliber size. These cavities, however, are only mildly contaminated by exogenous particles. PMID:22490236

Comparison of retinal vessel measurements using adaptive optics scanning laser ophthalmoscopy and optical coherence tomography.

PubMed

Arichika, Shigeta; Uji, Akihito; Ooto, Sotaro; Muraoka, Yuki; Yoshimura, Nagahisa

2016-05-01

We compared adaptive optics scanning laser ophthalmoscopy (AOSLO) and optical coherence tomography (OCT) vessel caliber measurements. AOSLO videos were acquired from 28 volunteers with healthy eyes. Artery measurements were made 0.5-1 disc diameters away from the optic disc margin. Individual segmented retinal arterial caliber was measured in synchronization with cardiac pulsation and averaged to obtain final horizontal retinal arterial caliber (ACH) and horizontal retinal arterial lumen (ALH). All OCT images were obtained with the Spectralis OCT, a spectral-domain OCT system. Vertical retinal arterial caliber (ACV) and vertical retinal arterial lumen (ALV) were measured on the same artery measured with AOSLO. Measurements made with the two imaging systems were compared. Average ACH, measured with AOSLO, was 123.4 ± 11.2 and average ALH was 101.8 ± 10.2 µm. Average ACV, measured with OCT, was 125.5 ± 11.4 and average ALV was 99.1 ± 10.6 µm. Both arterial caliber (r = 0.767, p < 0.0001) and arterial lumen (r = 0.81, p < 0.0001) measurements were significantly correlated between imaging modalities. Additionally, ACH and ACV were not significantly different (p = 0.16). However, ALH measurements were significantly higher than ALV measurements (p = 0.03). Vessel measurements made with AOSLO and OCT were well correlated. Moreover, plasma is visible and distinguishable from the retinal vessel wall in AOSLO images but not in OCT images. Therefore, AOSLO may measure vessel width more precisely than OCT.

Two cases of the double inferior venae cavae.

PubMed

Yano, R; Hayakawa, D; Emura, S; Chen, H; Ozawa, Y; Taguchi, H; Shoumura, S

2000-10-01

Two cases of the double inferior venae cavae (IVC) were found during the student dissection practice in 1997 in Gifu University School of Medicine. On the first case (70-year-old male), the calibers of the right and left IVC were 15 mm and 13 mm, respectively. An anastomosis (4-mm caliber) ran obliquely from the left internal iliac vein to the right IVC. On the second case (86-year-old male), the calibers of the right and left IVC were 15 mm and 10 mm, respectively. We found no anastomosis between the right and left IVC. Each IVC was observed behind the ureter. Both cases belong to Type BC of the classification of McClure and Butler (1925), that is based on the combinations of the right and left IVC, and on their location to the ureters. Both cases also belong to Type II-b-2 of the classification of Takemoto et al. (1978), that is based on the calibers of the right and left IVC and on the running course of the interiliac vein. These are the first and second cases among 808 cadavers in Gifu University School of Medicine and the 93rd and 94th cases in Japan since 1901.

Low velocity gunshot wounds result in significant contamination regardless of ballistic characteristics.

PubMed

Weinstein, Joseph; Putney, Emily; Egol, Kenneth

2014-01-01

Controversy exists among the orthopedic community regarding the treatment of gunshot injuries. No consistent treatment algorithm exists for treatment of low energy gunshot wound (GSW) trauma. The purpose of this study was to critically examine the wound contamination following low velocity GSW based upon bullet caliber and clothing fiber type found within the injury track. Four types of handguns were fired at ballistic gel from a 10-foot distance. Various clothing materials were applied (denim, cotton, polyester, and wool) circumferentially around the tissue agar in a loose manor. A total of 32 specimens were examined. Each caliber handgun was fired a minimum of 5 times into a gel. Regardless of bullet caliber there was gross contamination of the entire bullet track in 100% of specimens in all scenarios and for all fiber types. Furthermore, as would be expected, the degree of contamination appeared to increase as the size of the bullet increased. Low velocity GSWs result in significant contamination regardless of bullet caliber and jacket type. Based upon our results further investigation of low velocity GSW tracks is warranted. Further clinical investigation should focus on the degree to which debridement should be undertaken.

Comparison of Gunshot Entrance Morphologies Caused by .40-Caliber Smith & Wesson, .380-Caliber, and 9-mm Luger Bullets: A Finite Element Analysis Study

PubMed Central

Matoso, Rodrigo Ivo; Freire, Alexandre Rodrigues; Santos, Leonardo Soriano de Mello; Daruge Junior, Eduardo; Rossi, Ana Claudia; Prado, Felippe Bevilacqua

2014-01-01

Firearms can cause fatal wounds, which can be identified by traces on or around the body. However, there are cases where neither the bullet nor gun is found at the crime scene. Ballistic research involving finite element models can reproduce computational biomechanical conditions, without compromising bioethics, as they involve no direct tests on animals or humans. This study aims to compare the morphologies of gunshot entrance holes caused by.40-caliber Smith & Wesson (S&W), .380-caliber, and 9×19-mm Luger bullets. A fully metal-jacketed.40 S&W projectile, a fully metal-jacketed.380 projectile, and a fully metal-jacketed 9×19-mm Luger projectile were computationally fired at the glabellar region of the finite element model from a distance of 10 cm, at perpendicular incidence. The results show different morphologies in the entrance holes produced by the three bullets, using the same skull at the same shot distance. The results and traits of the entrance holes are discussed. Finite element models allow feasible computational ballistic research, which may be useful to forensic experts when comparing and analyzing data related to gunshot wounds in the forehead. PMID:25343337

Comparison Between Different Processing Schedules for the Development of Ultrafine-Grained Dual-Phase Steel

NASA Astrophysics Data System (ADS)

Karmakar, Anish; Sivaprasad, S.; Nath, S. K.; Misra, R. D. K.; Chakrabarti, Debalay

2014-05-01

A comparative study was carried out on the development of ultrafine-grained dual-phase (DP) (ferrite-martensite) structures in a low-carbon microalloyed steel processed using two thermomechanical processing routes, (i) intercritical deformation and (ii) warm-deformation and intercritical annealing. The samples were deformed using Gleeble3500® simulator, maintaining a constant total strain ( ɛ = 1) and strain rate ( = 1/s). Evolution of microstructure and micro-texture was investigated by SEM, TEM, and EBSD. Ultrafine-grained DP structures could be formed by careful selection of deformation temperature, T def (for intercritical deformation) or annealing temperature, T anneal (for warm-deformation and annealing). Overall, the ferrite grain sizes ranged from 1.5 to 4.0 μm, and the sizes and fractions of the uniformly distributed fine-martensitic islands ranged from 1.5 to 3.0 μm and 15 to 45 pct, respectively. Dynamic strain-induced austenite-to-ferrite transformation followed by continuous (dynamic) recrystallization of the ferrite dictated the grain refinement during intercritical deformation, while, continuous (static) recrystallization by pronounced recovery dictated the grain refinement during the warm-deformation and the annealing. Regarding intercritical deformation, the samples cooled to T def indicated finer grain size compared with the samples heated to T def, which are explained in terms of the effects of strain partitioning on the ferrite and the heating during deformation. Alpha-fiber components dominated the texture in all the samples, and the fraction of high-angle boundaries (with >15 deg misorientation) increased with the increasing T def or T anneal, depending on the processing schedule. Fine carbide particles, microalloyed precipitates and austenitic islands played important roles in defining the mechanism of grain refinement that involved retarding conventional ferrite recrystallization and ferrite grain growth. With regard to the intercritical deformation, warm-deformation followed by annealing is a simpler process to control in the rolling mill; however, the need for high-power rolling mill and controlled annealing facility imposes industrial challenges.

Urban adaptation can roll back warming of emerging megapolitan regions

PubMed Central

Georgescu, Matei; Morefield, Philip E.; Bierwagen, Britta G.; Weaver, Christopher P.

2014-01-01

Modeling results incorporating several distinct urban expansion futures for the United States in 2100 show that, in the absence of any adaptive urban design, megapolitan expansion, alone and separate from greenhouse gas-induced forcing, can be expected to raise near-surface temperatures 1–2 °C not just at the scale of individual cities but over large regional swaths of the country. This warming is a significant fraction of the 21st century greenhouse gas-induced climate change simulated by global climate models. Using a suite of regional climate simulations, we assessed the efficacy of commonly proposed urban adaptation strategies, such as green, cool roof, and hybrid approaches, to ameliorate the warming. Our results quantify how judicious choices in urban planning and design cannot only counteract the climatological impacts of the urban expansion itself but also, can, in fact, even offset a significant percentage of future greenhouse warming over large scales. Our results also reveal tradeoffs among different adaptation options for some regions, showing the need for geographically appropriate strategies rather than one size fits all solutions. PMID:24516126

Applications of Computer Simulation Methods in Plastic Forming Technologies for Magnesium Alloys

NASA Astrophysics Data System (ADS)

Zhang, S. H.; Zheng, W. T.; Shang, Y. L.; Wu, X.; Palumbo, G.; Tricarico, L.

2007-05-01

Applications of computer simulation methods in plastic forming of magnesium alloy parts are discussed. As magnesium alloys possess very poor plastic formability at room temperature, various methods have been tried to improve the formability, for example, suitable rolling process and annealing procedures should be found to produce qualified magnesium alloy sheets, which have the reduced anisotropy and improved formability. The blank can be heated to a warm temperature or a hot temperature; a suitable temperature field is designed, tools should be heated or the punch should be cooled; suitable deformation speed should be found to ensure suitable strain rate range. Damage theory considering non-isothermal forming is established. Various modeling methods have been tried to consider above situations. The following situations for modeling the forming process of magnesium alloy sheets and tubes are dealt with: (1) modeling for predicting wrinkling and anisotropy of sheet warm forming; (2) damage theory used for predicting ruptures in sheet warm forming; (3) modeling for optimizing of blank shape and dimensions for sheet warm forming; (4) modeling in non-steady-state creep in hot metal gas forming of AZ31 tubes.

Socioeconomic Representativeness and the Draft

DTIC Science & Technology

1980-06-01

l that the quality of recruits who enter the services ( especiall the Army) is of lover caliber than historically experienced. Proponents of...the "quality" of recruits who enter the services ( especially the Army) is of lower caliber than historically experienced. Proponents of conscription...draft, especially when considering peacetime conscrip- tion. The strength of the argument for the draft was held to be that all eligible men would serve

The Middle Temporal Artery: Surgical Anatomy and Exposure for Cerebral Revascularization.

PubMed

Rubio, Roberto Rodriguez; Lawton, Michael T; Kola, Olivia; Tabani, Halima; Yousef, Sonia; Meybodi, Ali Tayebi; Burkhardt, Jan-Karl; El-Sayed, Ivan; Benet, Arnau

2018-02-01

The middle temporal artery (MTA) is the proximal medial branch of the superficial temporal artery (STA), supplying the temporalis muscle along with deep temporal arteries. Its use in vascularized flaps for reconstructive and otologic procedures has been described, yet its potential use in neurosurgery has not been studied. We report a novel technique for exposing the MTA and evaluated its characteristics for extracranial-intracranial cerebrovascular bypass. After a curvilinear frontotemporal incision in 10 cadaveric specimens, the STA was dissected from distal to proximal. The horizontal portion of MTA was found posterolateral to the posterior end of the zygomatic root and was followed proximally until its origin and distally until its 2 terminal branches. The total length, visible branches, and caliber of MTA were measured. The mean total harvested length of MTA was 31.7 ± 5.1 mm, with an average proximal caliber of 1.7 ± 0.4 mm, and distal caliber of 1.3 ± 0.5 mm. There were 4-6 terminal MTA branches. The caliber of the proximal STA trunk was 2.5 ± 0.5 mm. The origin of the MTA was visible with a mean distance of 16.9 ± 4.8 mm inferior to the PEZR. The parotid gland was traversed and a communicating auriculotemporal nerve to the temporal branch of the facial nerve crossed MTA in 2 specimens. MTA can be safely harvested with an anterolateral approach, following its horizontal portion at the level of the zygomatic root, which is constant. The length and caliber of MTA makes it a potential alternative donor vessel or interposition graft for extracranial-intracranial bypass, especially when other donors are unavailable. Copyright © 2017 Elsevier Inc. All rights reserved.

Retaining {1 0 0} texture from initial columnar grains in 6.5 wt% Si electrical steels

NASA Astrophysics Data System (ADS)

Liang, Ruiyang; Yang, Ping; Mao, Weimin

2017-11-01

6.5 wt% Si electrical steel is a superior soft magnetic material with excellent magnetic properties which highly depends on texture. In this study, based on the heredity of 〈0 0 1〉 orientation in columnar grains, columnar grains are used as the initial material to prepare non-oriented 6.5 wt% Si electrical steel with excellent magnetic properties. EBSD and XRD techniques are adopted to explore the structure and texture evolution during hot rolling, warm rolling, cold rolling and annealing. The results show that, due to the heredity of "structure and texture" from the initial strong {1 0 0} columnar grains, annealed sheet with {1 0 0}〈0 0 1〉 texture had better magnetic properties, which can be used as non-oriented high-silicon electrical steel. Both preferred cube grain nucleation in deformed {1 1 3}〈3 6 1〉 grains in subsurface and coarse {1 0 0}〈0 0 1〉 deformed grains in center layer show the effect of initial columnar grains with {1 0 0} texture.

Homemade Heavy Caliber Rifles-Two Unusual Firearms.

PubMed

Yalçın Sarıbey, Aylin; Hannam, Abigail Grace

2016-05-01

Historically, in crimes involving heavy caliber rifles, only conventional factory-made versions have been used. However, in recent years the number of homemade long-barreled rifles is increasing. The characteristics of two such firearms that have been submitted to the Turkish Criminal Laboratory are discussed here. When the main parts of the guns were examined in detail, it was noted that nearly all of the parts had been made carelessly, with several structural defects visible. It was determined that the homemade heavy caliber rifles were unfit for efficient use and it was possible that they could have seriously harmed the shooter had they been fired. The development of these kinds of gun and the possibility of their use spreading throughout the country in terrorist attacks could cause a serious threat to national security. © 2015 American Academy of Forensic Sciences.

Subcaliber Guns

DTIC Science & Technology

1988-06-16

310-6 11. TITLE (Include Security Classification) "SUBCALIBER GUNS " 12. PERSONAL AUTHOR(S) 13a. TYPE OF REPORT 13b. TIME COVERED 14. DATE OF REPORT...necessary and identify by block number) FIELD GROUP SUB-GROUP 4Large caliber weapons, .,Subcaliber guns (" J-) Parent weapons.; Small caliber weapons’y...19, ABSTRACT (Continue on reverse if necessary and identify by block number) Provides procedures for determining the suitability of subcaliber guns

Measuring the Blast and Ballistic Performance of Armor

DTIC Science & Technology

2015-10-15

Typical ballistic test instrumentation is depicted in Fig. 1. The gun system employs a Mann barrel , available in a range of calibers1 (e.g., .22 cal...setup. (A) Mann barrel gun system; (B) computer and data acquisition interface; (C) remote, manual trigger; (D) velocity screens; (E) high speed video...1 Caliber corresponds to the diameter of the gun barrel , usually expressed in inches; e.g., .30 cal

Impulse noise generated by starter pistols

PubMed Central

Meinke, Deanna K.; Finan, Donald S.; Soendergaard, Jacob; Flamme, Gregory A.; Murphy, William J.; Lankford, James E.; Stewart, Michael

2015-01-01

Objective This study describes signals generated by .22 and .32 caliber starter pistols in the context of noise-induced hearing loss risk for sports officials and athletes. Design Acoustic comparison of impulses generated from typical .22 and .32 caliber starter pistols firing blanks were made to impulses generated from comparable firearms firing both blanks and live rounds. Acoustic characteristics are described in terms of directionality and distance from the shooter in a simulated outdoor running track. Metrics include peak sound pressure levels (SPL), A-weighted equivalent 8-hour level (LeqA8), and maximum permissible number of individual shots, or maximum permissible exposures (MPE) for the unprotected ear. Results Starter pistols produce peak SPLs above 140 dB. The numbers of MPEs are as few as five for the .22-caliber starter pistol, and somewhat higher (≤25) for the .32-caliber pistol. Conclusion The impulsive sounds produced by starter pistols correspond to MPE numbers that are unacceptably small for unprotected officials and others in the immediate vicinity of the shooter. At the distances included in this study, the risk to athletes appears to be low (when referencing exposure criteria for adults), but the sound associated with the starter pistol will contribute to the athlete’s overall noise exposure. PMID:23373743

Use of a marshmallow bolus for evaluating lower esophageal mucosal rings.

PubMed

Ott, D J; Kelley, T F; Chen, M Y; Gelfand, D W; Wu, W C

1991-07-01

Sixty-three patients (35 women, 28 men; mean age 55 yr) with lower esophageal mucosal ring shown radiographically were examined with a semi-solid bolus consisting of a portion of a standard marshmallow. The most common symptom was dysphagia, present in 46 (73%) patients. Impaction of the marshmallow bolus by the ring occurred in 40 (63%) of the 63 patients, and produced symptoms in 27 (68%) of these 40 patients. Nine (14%) rings were detected radiographically only with a solid bolus; eight of these patients had dysphagia and seven rings were 20 mm or less in caliber. Impaction related to ring caliber, and was found in all 17 (100%) rings that were 13 mm or less in diameter, in 17/24 (71%) 14- to 19-mm rings, and in 6/22 (27%) rings 20 mm or more in caliber. Endoscopy in 23 patients detected 16 (70%) rings, and also depended on ring caliber: less than or equal to 13 mm, 6/6 (100%); 14-19 mm, 5/9 (56%); greater than or equal to 20 mm, 5/8 (63%). Marshmallow impaction occurred in 17 (74%) of 23 patients who had endoscopy; three of the 23 patients had normal endoscopy. In conclusion, radiographic examination supplemented by the use of a marshmallow bolus best detects lower esophageal mucosal ring.

Estimation of retinal vessel caliber using model fitting and random forests

NASA Astrophysics Data System (ADS)

Araújo, Teresa; Mendonça, Ana Maria; Campilho, Aurélio

2017-03-01

Retinal vessel caliber changes are associated with several major diseases, such as diabetes and hypertension. These caliber changes can be evaluated using eye fundus images. However, the clinical assessment is tiresome and prone to errors, motivating the development of automatic methods. An automatic method based on vessel crosssection intensity profile model fitting for the estimation of vessel caliber in retinal images is herein proposed. First, vessels are segmented from the image, vessel centerlines are detected and individual segments are extracted and smoothed. Intensity profiles are extracted perpendicularly to the vessel, and the profile lengths are determined. Then, model fitting is applied to the smoothed profiles. A novel parametric model (DoG-L7) is used, consisting on a Difference-of-Gaussians multiplied by a line which is able to describe profile asymmetry. Finally, the parameters of the best-fit model are used for determining the vessel width through regression using ensembles of bagged regression trees with random sampling of the predictors (random forests). The method is evaluated on the REVIEW public dataset. A precision close to the observers is achieved, outperforming other state-of-the-art methods. The method is robust and reliable for width estimation in images with pathologies and artifacts, with performance independent of the range of diameters.

2011 International Infantry and Joint Services Small Arms Systems Symposium, Exhibition and Firing Demonstration

DTIC Science & Technology

2011-05-26

Machine Gun 24 12.7mm NATO Nominated Weapon United States – General Dynamics M2 Heavy Barrel Machine Gun 25...Explosively-Clad Refractory Barrel Liners for Small Caliber Machine Guns , Dr. Douglas Taylor, TPL, Inc. 12299 - The HAMR Project, Mr. Xavier Gavage, FN Herstal... Barrel Liners for Small Caliber Machine Guns Dr. Douglas Taylor, TPL, Inc. 12330 - 40mm Low Velocity Air-Burst Munitions System Mr.

Choroidal Thickness, Photoreceptor Thickness, and Retinal Vascular Caliber Alterations in Dark Adaptation.

PubMed

Alagöz, Cengiz; Pekel, Gökhan; Alagöz, Neşe; Sayın, Nihat; Yüksel, Kemal; Yıldırım, Yusuf; Yazıcı, Ahmet Taylan

2016-12-01

Our aim was to evaluate the alterations of subfoveal choroidal thickness (SFCT), photoreceptor layer thickness (PRT), and retinal vessel diameter in the dark and light adaptation. Twenty-four eyes of 24 healthy volunteers (12 males, 12 females) were included in this cross-sectional and observational study. The SFCT, PRT, retinal arteriole, and venule caliber measurements were performed with spectral domain optical coherence tomography in the dark (0.0 cd/m 2 ) and under light (80 cd/m 2 ) adapted conditions. The mean age of the participants was 30.4 ± 4.4 years (range: 22-42). The SFCT increased statistically significantly in dark adaptation (p < 0.001), then returned to baseline values following light adaptation. The PRT, retinal arteriole, and venule caliber measurements were similar in the dark and light (p > 0.05). While SFCT increased, PRT, and retinal vessel diameter did not change following transition from light to dark.

Ultrasonic Measurements of Bore Temperature in Large Caliber Guns

NASA Astrophysics Data System (ADS)

Yuhas, Donald E.; Mutton, Mark J.; Remiasz, Jack R.; Vorres, Carol L.

2009-03-01

The Navy has a need to measure temperatures at critical areas on large caliber gun inner bore surfaces to insure appropriate action is taken in case of a misfire. Inappropriate actions could result in the loss of life and the disabling of a naval warship. In this report we describe the development of an ultrasonic-based sensor capable of non-intrusively measuring internal bore temperature. The results obtained during live fire field trials will be presented.

Origin of the 44-mm Behind-Armor Blunt Trauma Standard

DTIC Science & Technology

2012-08-01

this work was completed, 9-mm and .357 impacts to both goats and clay (unpubl ished data), but was never fully completed or pub- 1 ished because of...frontrunner, were defined and tested on goats as an initial measure of serious injury and lethality. Armored, anesthetized goats were impacted with both the...38 Special and .22 caliber projectiles. Goldfarb et al 17 per- fanned follow-up studies using the same goat model and the same caliber projectiles

A Computational Study of Laminate Transparent Armor Impacted by FSP

DTIC Science & Technology

2009-06-01

of Hsieh et al [1], on targets consisting of 3mm PC-12mm PMMA-3mm PC impacted by 17-gr, 0.22 caliber fragment simulating projectile (FSP) at impact...results from the experiments of Hsieh et al [1], on targets consisting of 3mm PC-12mm PMMA-3mm PC impacted by 17-gr, 0.22 caliber fragment simulating...investigate several different analysis techniques to qualitatively determine their accuracy when compared with experiments of Hsieh et al [1]. The

The 2008 Battle of Sadr City: Reimagining Urban Combat

DTIC Science & Technology

2013-01-01

so intense that some of the Strykers ran out of ammunition for the .50 caliber machine guns in their remote weapons system. Adding to the confusion...review. Out of all the day’s unusual violence, the one thing that stood out in their memories was the lone gunman with his RPK machine gun . Collings’s...platoon suppressed the enemy effectively using the .50 caliber machine guns in the remote weapons systems. They also called in AH-64 Apache attack

The Marine Corps Ability to Conduct Surface Amphibious Transport is at Risk

DTIC Science & Technology

2013-05-03

Barrel .50 caliber Machine Gun and the destruction ability of a high explosive grenade with the Mk 19 40 mm Grenade Launcher. Each individual AAV...the current AAV offer protection from up to caliber 12.7 mm rounds from the enemy, it provides a direct fire support capability with the M2 Heavy...are not traditionally designed to provide a high degree of comfort to the inhabitants. They are machines of necessity. As a result, many argue

Elimination of Airborne Lead Contamination from Caliber .22 Ammunition.

DTIC Science & Technology

1987-06-01

R191 365 ELIMINATION OF AIRBORNE LEAD CONTAMINATION FROM CALIBER 1/1 Ri ’ 3 5 22 N INITION(U) ARMY ARMAMENT RESEARCH DE VELOPMENT AM D...E JUNE 1987 U. S. MMW ARKM SRcKH, IDVROPMEff n U COOE US" ARMY EARMLMA CLOSE COMBAT ARMAMENT CENTER - MUNITBONS Et CHEMICAL COMMANDR D RA - A9~laIENT...Command tasked the U.S. Army Armament, Research , Development and Engineering Center (ARDEC) to determine if the sources of lead contamination could be

Characterization and Discrimination of Large Caliber Gun Blast and Flash Signatures

DTIC Science & Technology

2011-10-01

from one end of a barrel (the muzzle) by the application of force at the other end. In conventional guns , force is provided by the combustion of a...projectile begins to accelerate down the barrel ; this is known as shot start. As the projectile traverses the gun barrel and additional volume becomes...flash that is used today resulted from this program’s report. Visible and ultraviolet (UV) spectra of 20 mm and .50 caliber machine gun firings were

Operational Resiliency Assessment of an Army Company Team

DTIC Science & Technology

2015-12-01

enemy with direct fire assets. For example, the Abrams tank employs a 120 millimeter main gun and a .50 caliber machine gun with which to engage...eight personnel each, complimented by two medium-caliber machine guns , an anti-armor section, and two dismounted anti-aircraft missile systems...Dismounted Infantry Squad 8 3 Anti-Aircraft Missile Team 1 2 Anti-Armor Section 1 2 PKM Med MG Machine Gun Team 1 2 2 12.7mm Heavy MG Tank Platoon 4 1

Lead-free hunting rifle ammunition: product availability, price, effectiveness, and role in global wildlife conservation.

PubMed

Thomas, Vernon George

2013-10-01

Proposals to end the use of lead hunting ammunition because of the established risks of lead exposure to wildlife and humans are impeded by concerns about the availability, price, and effectiveness of substitutes. The product availability and retail prices of different calibers of lead-free bullets and center-fire rifle ammunition were assessed for ammunition sold in the USA and Europe. Lead-free bullets are made in 35 calibers and 51 rifle cartridge designations. Thirty-seven companies distribute internationally ammunition made with lead-free bullets. There is no major difference in the retail price of equivalent lead-free and lead-core ammunition for most popular calibers. Lead-free ammunition has set bench-mark standards for accuracy, lethality, and safety. Given the demonstrated wide product availability, comparable prices, and the effectiveness of high-quality lead-free ammunition, it is possible to phase out the use of lead hunting ammunition world-wide, based on progressive policy and enforceable legislation.

A numerical investigation of viscous, incompressible flow past an axisymmetric body with and without spin

NASA Astrophysics Data System (ADS)

Weber, K. F.

1985-12-01

This study deals with a preliminary investigation of the effects of spin on the axisymmetric flow past a body of revolution. The study has its genesis larger problem of Magnus forces on spinning bodies at angle of attack. However, the fundamental behavior that arises when a spinning body is placed in a uniform stream is still not well understood; therefore, the problem of axisymmetric flow with spin was undertaken. The body consists of a 3-caliber cant-ogive blunted by a spherical nosecap, a 2-caliber cylindrical section, and a 1-caliber boattail. Numerical solutions of the compressible laminar Navier-Stokes equations are obtained using a modified version of the implicit-explicit method developed by MacCormack in 1981. The benchmark problem is the nonspinning body in uniform flow at a Reynolds number of 1.14. The results show that the modified method performs well and allows time steps that are in order of magnitude greater than those permitted by explicit stability criteria.

The effect of firearm muzzle gases on the backspatter of blood.

PubMed

Taylor, Michael C; Laber, Terry L; Epstein, Barton P; Zamzow, Dan S; Baldwin, David P

2011-09-01

Injuries caused by gunshots can produce what bloodstain pattern analysts know as "backspatter." Observations about the presence or absence of backspatter on an individual may be used in court as evidence of guilt or innocence. The discharge of three firearms (.22 caliber revolver, .38 caliber revolver, and .308 caliber rifle) and the resulting impact of bullets on a blood source were recorded using high-speed digital video imaging. Blood droplets, firearm muzzle gases, and ballistic shock waves were visualized using standard reflected light and shadowgraphy imaging techniques. A significant interaction between air currents, muzzle gases, and particulate material emanating from the firearms upon discharge with backspattered blood was observed. Blood droplets, initially spattered back toward the firearm and the shooter, were observed to change direction under the influence of firearm-induced air currents and were blown forward toward and beyond their original source location. Implications for experts testifying in court and for bloodstain pattern instructors are discussed.

The Effect of Firearm Muzzle Gases on the Backspatter of Blood

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, M.C.; Laber, T.L.; Epstein, B.P.

2010-05-12

Injuries caused by gunshots can produce what bloodstain pattern analysts know as 'backspatter.' Observations about the presence or absence of backspatter on an individual may be used in court as evidence of guilt or innocence. The discharge of three firearms (.22 caliber revolver, .38 caliber revolver, and .308 caliber rifle) and the resulting impact of bullets on a blood source were recorded using high-speed digital video imaging. Blood droplets, firearm muzzle gases, and ballistic shock waves were visualized using standard reflected light and shadowgraphy imaging techniques. A significant interaction between air currents, muzzle gases, and particulate material emanating from themore » firearms upon discharge with backspattered blood was observed. Blood droplets, initially spattered back toward the firearm and the shooter, were observed to change direction under the influence of firearm-induced air currents and were blown forward toward and beyond their original source location. Implications for experts testifying in court and for bloodstain pattern instructors are discussed.« less

The association of longitudinal trend of fasting plasma glucose with retinal microvasculature in people without established diabetes.

PubMed

Hu, Yin; Niu, Yong; Wang, Dandan; Wang, Ying; Holden, Brien A; He, Mingguang

2015-01-22

Structural changes of retinal vasculature, such as altered retinal vascular calibers, are considered as early signs of systemic vascular damage. We examined the associations of 5-year mean level, longitudinal trend, and fluctuation in fasting plasma glucose (FPG) with retinal vascular caliber in people without established diabetes. A prospective study was conducted in a cohort of Chinese people age ≥40 years in Guangzhou, southern China. The FPG was measured at baseline in 2008 and annually until 2012. In 2012, retinal vascular caliber was assessed using standard fundus photographs and validated software. A total of 3645 baseline nondiabetic participants with baseline and follow-up data on FPG for 3 or more visits was included for statistical analysis. The associations of retinal vascular caliber with 5-year mean FPG level, longitudinal FPG trend (slope of linear regression-FPG), and fluctuation (standard deviation and root mean square error of FPG) were analyzed using multivariable linear regression analyses. Multivariate regression models adjusted for baseline FPG and other potential confounders showed that a 10% annual increase in FPG was associated independently with a 2.65-μm narrowing in retinal arterioles (P = 0.008) and a 3.47-μm widening in venules (P = 0. 0.004). Associations with mean FPG level and fluctuation were not statistically significant. Annual rising trend in FPG, but not its mean level or fluctuation, is associated with altered retinal vasculature in nondiabetic people. Copyright 2015 The Association for Research in Vision and Ophthalmology, Inc.

Global warming potential of pavements

NASA Astrophysics Data System (ADS)

Santero, Nicholas J.; Horvath, Arpad

2009-09-01

Pavements comprise an essential and vast infrastructure system supporting our transportation network, yet their impact on the environment is largely unquantified. Previous life-cycle assessments have only included a limited number of the applicable life-cycle components in their analysis. This research expands the current view to include eight different components: materials extraction and production, transportation, onsite equipment, traffic delay, carbonation, lighting, albedo, and rolling resistance. Using global warming potential as the environmental indicator, ranges of potential impact for each component are calculated and compared based on the information uncovered in the existing research. The relative impacts between components are found to be orders of magnitude different in some cases. Context-related factors, such as traffic level and location, are also important elements affecting the impacts of a given component. A strategic method for lowering the global warming potential of a pavement is developed based on the concept that environmental performance is improved most effectively by focusing on components with high impact potentials. This system takes advantage of the fact that small changes in high-impact components will have more effect than large changes in low-impact components.

Evaluation of Military Range Berm Effectiveness in Protecting Red-cockaded Woodpecker Foraging and Nesting Habitat

DTIC Science & Technology

2011-04-01

Benning – Malone 5 Malone 5 is an unbermed SA machine gun (firing 7.62 mm or smaller caliber rounds) range with elevated firing and target boxes (~1...plots, not originally allocated. Fort Stewart – Kilo The Kilo range on Fort Stewart is an unbermed SA machine gun (firing 7.62 mm or smaller...is a bermed SA machine gun (firing 7.62 mm or smaller caliber rounds) range with elevated firing boxes and targets (~1-m high; Figures 6 and 7). The

Antimony content of inorganic gunshot residue (IGSR) produced by 0.22 caliber rimfire ammunition having free-antimony primer.

PubMed

Zeichner, Arie

2017-01-01

In a recent paper published in Forensic Science International (FSI), Lucas et al. (2016) claimed that muzzle discharge of 0.22 caliber rimfire ammunition is more likely to incorporate particles from the bullet surface than those retained on the firearm and that characteristic particles containing Pb, Ba and Sb formed from known Sb-free primers are likely to be more prevalent in muzzle discharge. It seems that this claim is not based on sufficient experimental results. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Shape effect of ultrafine-grained structure on static fracture toughness in low-alloy steel.

PubMed

Inoue, Tadanobu; Kimura, Yuuji; Ochiai, Shojiro

2012-06-01

A 0.4C-2Si-1Cr-1Mo steel with an ultrafine elongated grain (UFEG) structure and an ultrafine equiaxed grain (UFG) structure was fabricated by multipass caliber rolling at 773 K and subsequent annealing at 973 K. A static three-point bending test was conducted at ambient temperature and at 77 K. The strength-toughness balance of the developed steels was markedly better than that of conventionally quenched and tempered steel with a martensitic structure. In particular, the static fracture toughness of the UFEG steel, having a yield strength of 1.86 GPa at ambient temperature, was improved by more than 40 times compared with conventional steel having a yield strength of 1.51 GPa. Furthermore, even at 77 K, the fracture toughness of the UFEG steel was about eight times higher than that of the conventional and UFG steels, despite the high strength of the UFEG steel (2.26 GPa). The UFG steel exhibited brittle fracture behavior at 77 K, as did the conventional steel, and no dimple structure was observed on the fracture surface. Therefore, it is difficult to improve the low-temperature toughness of the UFG steel by grain refinement only. The shape of crystal grains plays an important role in delamination toughening, as do their refinement and orientation.

Shape effect of ultrafine-grained structure on static fracture toughness in low-alloy steel

PubMed Central

Inoue, Tadanobu; Kimura, Yuuji; Ochiai, Shojiro

2012-01-01

A 0.4C-2Si-1Cr-1Mo steel with an ultrafine elongated grain (UFEG) structure and an ultrafine equiaxed grain (UFG) structure was fabricated by multipass caliber rolling at 773 K and subsequent annealing at 973 K. A static three-point bending test was conducted at ambient temperature and at 77 K. The strength–toughness balance of the developed steels was markedly better than that of conventionally quenched and tempered steel with a martensitic structure. In particular, the static fracture toughness of the UFEG steel, having a yield strength of 1.86 GPa at ambient temperature, was improved by more than 40 times compared with conventional steel having a yield strength of 1.51 GPa. Furthermore, even at 77 K, the fracture toughness of the UFEG steel was about eight times higher than that of the conventional and UFG steels, despite the high strength of the UFEG steel (2.26 GPa). The UFG steel exhibited brittle fracture behavior at 77 K, as did the conventional steel, and no dimple structure was observed on the fracture surface. Therefore, it is difficult to improve the low-temperature toughness of the UFG steel by grain refinement only. The shape of crystal grains plays an important role in delamination toughening, as do their refinement and orientation. PMID:27877493

Quantification of Hydrodynamic Forcing on Smart Munitions on the Beach Face - Designof Smart Munitions

NASA Astrophysics Data System (ADS)

Cristaudo, D.; Bruder, B. L.; Puleo, J. A.

2016-12-01

Millions of unexploded ordnance (munitions) are located in the waters off of US coasts. They canmigrate to the beach and become a peril to local beach users. The research objective is to quantifythe small scale processes on the beach face responsible for munition mobility. Several experimentsat different sites with different wave and bathymetry conditions will be conducted. Realisticsurrogate munitions were constructed to facilitate the future experiments. Six different munitiontypes were replicated, selecting a range of calibers covering a variety of dimensions from 20 mmto 155 mm. The surrogates are made "smart" by designing them to house several internal sensors(the quantity depends on the available space inside the surrogate itself) that will aid in estimatingthe characteristics of their mobility. Each smart surrogate replicates the mass, center of gravity,and moment of inertia of the actual munition as close as possible. The sensors used inside the smartsurrogate munitions include: inertial motion units (IMU) to derive the surrogate position; Ubisenseultra-wideband tags for positioning in dry conditions; a Slamstick shock sensor to quantify thewave impact force on the surrogate; photocells to detect rolling and burial; and a pressure sensorto measure the water depth. The procedure of designing the smart surrogate munitions and sensorcapabilities will be presented.

White cell count in the normal range and short-term and long-term mortality: international comparisons of electronic health record cohorts in England and New Zealand.

PubMed

Shah, Anoop Dinesh; Thornley, Simon; Chung, Sheng-Chia; Denaxas, Spiros; Jackson, Rod; Hemingway, Harry

2017-02-17

Electronic health records offer the opportunity to discover new clinical implications for established blood tests, but international comparisons have been lacking. We tested the association of total white cell count (WBC) with all-cause mortality in England and New Zealand. Primary care practices in England (ClinicAl research using LInked Bespoke studies and Electronic health Records (CALIBER)) and New Zealand (PREDICT). Analysis of linked electronic health record data sets: CALIBER (primary care, hospitalisation, mortality and acute coronary syndrome registry) and PREDICT (cardiovascular risk assessments in primary care, hospitalisations, mortality, dispensed medication and laboratory results). People aged 30-75 years with no prior cardiovascular disease (CALIBER: N=686 475, 92.0% white; PREDICT: N=194 513, 53.5% European, 14.7% Pacific, 13.4% Maori), followed until death, transfer out of practice (in CALIBER) or study end. HRs for mortality were estimated using Cox models adjusted for age, sex, smoking, diabetes, systolic blood pressure, ethnicity and total:high-density lipoprotein (HDL) cholesterol ratio. We found 'J'-shaped associations between WBC and mortality; the second quintile was associated with lowest risk in both cohorts. High WBC within the reference range (8.65-10.05×10 9 /L) was associated with significantly increased mortality compared to the middle quintile (6.25-7.25×10 9 /L); adjusted HR 1.51 (95% CI 1.43 to 1.59) in CALIBER and 1.33 (95% CI 1.06 to 1.65) in PREDICT. WBC outside the reference range was associated with even greater mortality. The association was stronger over the first 6 months of follow-up, but similar across ethnic groups. Clinically recorded WBC within the range considered 'normal' is associated with mortality in ethnically different populations from two countries, particularly within the first 6 months. Large-scale international comparisons of electronic health record cohorts might yield new insights from widely performed clinical tests. NCT02014610. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Analysis of retinal capillaries in patients with type 1 diabetes and nonproliferative diabetic retinopathy using adaptive optics imaging.

PubMed

Lombardo, Marco; Parravano, Mariacristina; Serrao, Sebastiano; Ducoli, Pietro; Stirpe, Mario; Lombardo, Giuseppe

2013-09-01

To illustrate a noninvasive method to analyze the retinal capillary lumen caliber in patients with Type 1 diabetes. Adaptive optics imaging of the retinal capillaries were acquired in two parafoveal regions of interest in eyes with nonproliferative diabetic retinopathy and unaffected controls. Measures of the retinal capillary lumen caliber were quantified using an algorithm written in Matlab by an independent observer in a masked manner. Comparison of the adaptive optics images with red-free and color wide fundus retinography images was also assessed. Eight eyes with nonproliferative diabetic retinopathy (eight patients, study group), no macular edema, and preserved visual acuity and eight control eyes (eight healthy volunteers; control group) were analyzed. The repeatability of capillary lumen caliber measurements was 0.22 μm (3.5%) with the 95% confidence interval between 0.12 and 0.31 μm in the study group. It was 0.30 μm (4.1%) with the 95% confidence interval between 0.16 and 0.43 μm in the control group. The average capillary lumen caliber was significantly narrower in eyes with nonproliferative diabetic retinopathy (6.27 ± 1.63 μm) than in the control eyes (7.31 ± 1.59 μm, P = 0.002). The authors demonstrated a noninvasive method to analyze, with micrometric scale of resolution, the lumen of retinal capillaries. The parafoveal capillaries were narrower in patients with Type 1 diabetes and nonproliferative diabetic retinopathy than in healthy subjects, showing the potential capability of adaptive optics imaging to detect pathologic variations of the retinal microvascular structures in vaso-occlusive diseases.

Devascularization of Head and Neck Paragangliomas by Direct Percutaneous Embolization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozyer, Umut, E-mail: umut_ozyer@yahoo.com; Harman, Ali; Yildirim, Erkan

2010-10-15

Preoperative transarterial embolization of head and neck paragangliomas using particulate agents has proven beneficial for decreasing intraoperative blood loss. However, the procedure is often incomplete owing to extensive vascular structure and arteriovenous shunts. We report our experience with embolization of these lesions by means of direct puncture and intratumoral injection of n-butyl cyanoacrylate (NBCA) or Onyx. Ten patients aged 32-82 years who were referred for preoperative embolization of seven carotid body tumors and three jugular paragangliomas were retrospectively analyzed. Intratumoral injections were primarily performed in four cases with multiple small-caliber arterial feeders and adjunctive to transarterial embolization in six casesmore » with incomplete devascularization. Punctures were performed under ultrasound and injections were performed under roadmap fluoroscopic guidance. Detailed angiographies were performed before and after embolization procedures. Control angiograms showed complete or near-complete devascularization in all tumors. Three tumors with multiple small-caliber arterial feeders were treated with primary NBCA injections. One tumor necessitated transarterial embolization after primary injection of Onyx. Six tumors showed regional vascularization from the vasa vasorum or small-caliber branches of the external carotid artery following the transarterial approach. These regions were embolized with NBCA injections. No technical or clinical complications related to embolization procedures occurred. All except one of the tumors were surgically removed following embolization. In conclusion, preoperative devascularization with percutaneous direct injection of NBCA or Onyx is feasible, safe, and effective in head and neck paragangliomas with multiple small-caliber arterial feeders and in cases of incomplete devascularization following transarterial embolization.« less

Automation of wear analysis for large caliber weapons

NASA Astrophysics Data System (ADS)

Salafia, Dominick; DeLeon, Norberto L.; Outlaw, James F.

1999-12-01

As part of the Test and Evaluation Command (TECOM) the Metrology and Simulation Division (MT-MS) at the U.S. Army Yuma Proving Ground (USAYPG) has the mission to measure and record the wear effects of conventional and experimental munitions on large caliber weapons. The primary objective is to ensure that the weapon to be fired will safely meet the mission requirements for the quantity and energy of the munitions under live fire testing. Currently, there are two criteria used to "deadline" a weapon. One is the actual physical wear tolerance. The other relates to the energy (zone) expended by the round and the subsequent fatigue induced in the microstructure of the gun tube. The latter is referred to as the Equivalent Full Charge (EFC) for the particular round. In order to maximize safety and reduce the time required to manually search records for the appropriate level of useful life, the Measurements and Simulation Branch of MT-MS at USAYPG has made use of the installation network such that critical information may be accessed from the local area network or the Internet. An electronic database has been constructed and the query routines have been written so that systems test personnel, test directors (TD), and other government organizations may conduct a search for a particular weapon. The user may enter specifications such as percent physical life, percent EFC life, caliber, model, modifications, and serial number or any combination thereof. This paper is intended to inform the engineering and scientific community, engaged in weapons performance evaluation using simulations and field testing, of the existence of wear analysis automation for large caliber weapons.

An Analysis of the Characteristics of Thoracic and Abdominal Injuries Due to Gunshot Homicides in Israel.

PubMed

Maiden, Nicholas R; Hiss, Jehuda; Gips, Hadas; Hocherman, Gil; Levin, Nadav; Kosachevsky, Olga; Vinokurov, Asya; Zelkowicz, Avraham; Byard, Roger W

2016-01-01

De-identified wound data from 197 homicidal gunshot postmortems were obtained between 2000 and 2008. Forensic ballistics data were only available for cases between 2004 and 2008. Males represent 91% of gunshot victims and were struck in the thorax/abdomen with an average of 2.3 bullets. The type of firearms involved were semi-automatic pistols in the predominant caliber 9-mm Luger and assault rifles in caliber 5.56 × 45 mm and caliber 7.62 × 39 mm Soviet, using full metal jacket bullets. The majority of shootings occurred at ranges of 1 m or greater. The most common bullet path was front to back in 66% of cases. Entry wounds occurred more often on the left side of the thorax, abdomen, and back. The most common critical organs/tissues to sustain bullet trauma in descending order were as follows: heart, lungs, liver, aorta, spleen, kidneys, and vena cava. Ribs were struck by most bullets that entered the thorax. © 2015 American Academy of Forensic Sciences.

Task-Based Teaching of English-Chinese Translation under "Caliber-Oriented Education to Success" Based on Web

NASA Astrophysics Data System (ADS)

Duan, Zhongyan

This paper, under 3-using principle in the philosophy of caliber-oriented education to success (CETS), makes a tentative qualitative study on the application of task-based approach in the teaching of English-Chinese translation based on the web. Translation teaching is characterized by its practicality. Therefore, the task-based approach can be employed to guide the web-based content collection and the process of English translation teaching. In this way, the prospect for enhancing student's translation ability is quite encouraging, which has been verified by one year's teaching.

Development of a Physical Employment Testing Battery for Armor Soldiers: 19D Cavalry Scout and 19K M1 Armor Crewman

DTIC Science & Technology

2015-12-01

M2 .50 Caliber Machine Gun on the Abrams Tank While wearing a task specific uniform weighing approximately 49 lb, Soldiers lifted the M2 .50...12 Engage Targets with a Caliber .50 M2 Machine Gun X 13 Lay a 120mm Mortar – Emplace Base Plate X 14 Lay a 120mm Mortar...17 Mount M2 .50 Cal Machine Gun Receiver on an Abrams Tank X 18 Stow Ammunition on an Abrams Tank (Load 120mm MPAT Round to the Ready Rack

Development of a Physical Employment Testing Battery for Infantry Soldiers: 11B Infantryman and 11C Infantryman-Indirect Fire

DTIC Science & Technology

2015-12-01

43 1.9 Images of Move Under Direct Fire (Task 10) 44 1.10 Engage Targets with a .50 Caliber M2 Machine Gun (Task 12) 45 1.11 Image of Lay a...Caliber M2 Machine Gun While wearing a fighting load (approximately 83 lb) and working as a member of a two-person team, Soldiers lifted and carried the... M2 HB Machine Gun with tripod (153 lb) a distance of 10 m. Army Standard: Successful completion of the task 13. Emplace Base Plate (11C

Development of a Physical Employment Testing Battery for Infantry Soldiers: 11B Infantryman and 11C Infantryman - Indirect Fire

DTIC Science & Technology

2015-12-01

25mm barrel install (Task 5) and engage targets with an M2 machine gun (Task 12). During these tasks, the performance of one individual will affect...TOW Missile Launcher on BFV (Task 8) 43 1.9 Images of Move Under Direct Fire (Task 10) 44 1.10 Engage Targets with a .50 Caliber M2 Machine Gun ...Engage Targets with a .50 Caliber M2 Machine Gun While wearing a fighting load (approximately 83 lb) and working as a member of a two-person team

Radar system components to detect small and fast objects

NASA Astrophysics Data System (ADS)

Hülsmann, Axel; Zech, Christian; Klenner, Mathias; Tessmann, Axel; Leuther, Arnulf; Lopez-Diaz, Daniel; Schlechtweg, Michael; Ambacher, Oliver

2015-05-01

Small and fast objects, for example bullets of caliber 5 to 10 mm, fired from guns like AK-47, can cause serious problems to aircrafts in asymmetric warfare. Especially slow and big aircrafts, like heavy transport helicopters are an easy mark of small caliber hand fire weapons. These aircrafts produce so much noise, that the crew is not able to recognize an attack unless serious problems occur and important systems of the aircraft fail. This is just one of many scenarios, where the detection of fast and small objects is desirable. Another scenario is the collision of space debris particles with satellites.

Microstructure Characterization of Weakly Textured and Fine Grained AZ61 Sheet

NASA Astrophysics Data System (ADS)

Berman, T. D.; Donlon, W.; Hung, C. K.; Milligan, P.; Decker, R.; Pollock, T. M.; Jones, J. W.

Formability in magnesium alloy sheet is strongly limited by a strong basal texture in the as-rolled material, which is difficulty to remove by thermal processing. We introduce a new process to the control of texture by combining Thixomolding and Thermomechanical Processing (TTMP). Plates of AZ61L with a divorced β-Mg17Al12 eutectic are produced by Thixomolding, resulting in a non-textured, fine grained (2.8 µm) precursor. Sheet produced from the plate by single pass warm-rolling exhibits a weaker texture, and more isotropic tensile deformation than generally observed in AZ-series alloy sheet. Recrystallization annealing produces a further reduction in texture and average grain size (2.3 µm) and results in nearly isotropic room temperature deformation, a yield strength of 220 MPa, and an elongation of 23%. Particle stimulated nucleation of new grains by the β-phase during both dynamic and static recrystallization, is critical for achieving the low levels of texture. The influence of β-phase distribution in microstructure development is discussed.

Parental history of hypertension is associated with narrower retinal arteriolar caliber in young girls.

PubMed

Gopinath, Bamini; Baur, Louise A; Hardy, Louise L; Wang, Jie Jin; Teber, Erdahl; Wong, Tien Y; Mitchell, Paul

2011-09-01

We aimed to assess the associations between parental history of hypertension and indicators of cardiovascular risk (retinal vessel diameter, presence of obesity, and elevated blood pressure) in prepubertal children. There were 1739 (77.7% of those eligible) 6-year-old students (863 girls and 876 boys) who were examined from a random cluster sample of 34 Sydney schools. Parents completed questionnaires about their medical conditions, including whether they have/had hypertension. Retinal images were taken with a digital fundus camera, and retinal vessel caliber was quantified using computer software. Anthropometric (height, weight, percentage of body fat, and body mass index) and blood pressure measures were collected. There were 160 children (9.2%) with a positive parental history of hypertension (either biological mother and/or father). Children with a positive versus negative parental history of hypertension had significantly higher body mass index (16.8 versus 16.5 kg/m(2); P=0.04) and systolic blood pressure (101.3 versus 99.8 mm Hg; P=0.01). Girls with positive versus negative parental history of hypertension had significantly higher diastolic blood pressure (≈3.1 mm Hg; P=0.01) and narrower retinal arteriolar caliber (≈4.3 μm; P=0.0004). Positive parental history of hypertension was not associated with mean retinal vascular caliber among boys. We show that a positive parental history of hypertension in healthy prepubertal girls, but not boys, is associated with narrower retinal arteriolar vessels, likely conveying a predisposition to develop hypertension later in life. These findings may indicate the need for cardiovascular disease prevention measures starting early in life among offspring of hypertensive parents.

Ambulatory Aortic Stiffness Is Associated With Narrow Retinal Arteriolar Caliber in Hypertensives: The SAFAR Study.

PubMed

Aissopou, Evaggelia K; Argyris, Antoniοs A; Nasothimiou, Efthimia G; Konstantonis, George D; Tampakis, Kostas; Tentolouris, Nikolaos; Papathanassiou, Miltiadis; Theodossiadis, Panagiotis G; Papaioannou, Theodoros G; Stehouwer, Coen D A; Sfikakis, Petros P; Protogerou, Athanassios D

2016-05-01

Arterial stiffness measured under static conditions reclassifies significantly cardiovascular (CV) risk and associates with narrower retinal arterioles. However, arterial stiffness exhibits circadian variation, thus single static stiffness recordings do not correspond to the "usual" 24 hr, awake, and asleep average arterial stiffness. We aimed to test the hypothesis that ambulatory 24 hr, awake, and asleep aortic (a) pulse wave velocity (PWV) associate with retinal vessel calibers, independently of confounders and of static arterial stiffness, in hypertensive individuals free from diabetes and CV disease. Digital retinal images were obtained (181 individuals, age: 53.9±10.7 years, 55.2% men) and retinal vessel calibers were measured with validated software to determine central retinal arteriolar and venular equivalents (CRAE and CRVE, respectively); ambulatory (24 hr, awake, asleep) and static office aPWV were estimated by Mobil-O-Graph; and static office carotid to femoral (cf) PWV by SphygmoCor. Regression analysis performed in 320 gradable retinal images showed that, after adjustment for confounders: (i) ambulatory aPWV was significantly associated with narrower retinal arterioles but not with venules; (ii) asleep aPWV had stronger associations with CRAE than awake aPWV; (iii) both ambulatory aPWV and cfPWV were associated mutually independently with narrower retinal arterioles; aPWV introduction in the model of cfPWV, improved model's R2 (P = 0.012). Similar discriminatory ability of 24 hr aPWV and of cfPWV to detect the presence of retinal arteriolar narrowing was found. Ambulatory aPWV, estimated by an operator-independent method, provides additional information to cfPWV regarding the associations of arterial stiffness with the retinal vessel calibers. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A safe model for creating blunt and penetrating ballistic injury.

PubMed

Graeber, G M; Belville, W D; Sepulveda, R A

1981-06-01

Minor modification of an existing readily available captive projectile weapon system has allowed development of a safe model for studying both penetrating ballistic and blunt tissue injury. A captive projectile weapon (defined as a firearm in which the projectile does not leave the weapon and in which the external wounding range is very limited) diminishes greatly the possibility of injury to personnel while it allows a high degree of reproducibility. The system has three parts: the pistol (wt 1.3 kg), a stainless steel stand, and a rack for holding the organ to be injured. It has been used 14 times in developing a canine model for the study of penetrating ballistic renal injury. When a 2 grain, .22 caliber charge is fired in the weapon, the .45 caliber captive projectile travels 7.5 cm and penetrates the kidney completely. The kinetic energy available for transfer from the projectile to the kidney and renal vessels totals 211 joules, which is comparable to the kinetic energy of projectiles for many law enforcement sidearms at 45.72 meters (50 yards) from the muzzle of the weapon. Comparison of the wounds showed complete reproducibility of injury (100%) over all 14 subjects [Entrance wound greater than or equal to .45 caliber (100%). Exit wound greater than or equal to .45 caliber (100%). Complete penetration (100%)]. This weapon system can be modified to duplicate the injury created by missiles from many small arms by modifying the captive projectile and/or the charge. Changing the leading surface of the captive projectile allows delivery of the energy over a broad surface such that blunt injuries can be simulated.

Estimation of pulmonary artery pressure in patients with primary pulmonary hypertension by quantitative analysis of magnetic resonance images.

PubMed

Murray, T I; Boxt, L M; Katz, J; Reagan, K; Barst, R J

1994-01-01

The use of magnetic resonance (MR) images for estimating mean pulmonary artery pressure (PAP) was tested by comparing main pulmonary artery (MPA) and middescending thoracic aorta (AO) caliber in 12 patients with primary pulmonary hypertension (PPH) with measurements made in eight other patients who were observed for diseases other than heart disease (controls). The ratio MPA/AO and the ratios of vessel caliber normalized to body surface area (MPAI and AOI, respectively) were computed. The PAP was obtained in all PPH patients and compared with caliber measurements. The PPH MPA (3.6 +/- 0.8 cm) was significantly larger than the control MPA (2.9 +/- 0.3 cm, p = 0.02); the PPH MPAI (2.8 +/- 0.7 cm/M2) was significantly greater than the control MPA (1.7 +/- 0.2 cm/M2, p < 0.0001). Control AO (2.2 +/- 0.3 cm) was significantly greater than PPH AO (1.6 +/- 0.4 cm, p < 0.0001); there was no significant difference between control AOI (1.3 +/- 0.2 cm/M2) and PPH AOI (1.2 +/- 0.2 cm/M2, p = 0.25). The PPH MPA/AO (2.3 +/- 0.6) was significantly greater than the control MPA/AO (1.3 +/- 0.1, p < 0.0001); overlap between MPA in the two groups was eliminated by indexing values to AO caliber (MPA/AO). Among PPH patients there was strong correlation between PAP and MPA/AO (PAP = 24 x MPA/AO + 3.7, r = 0.7, p < 0.01). Increased MPA/AO denotes the presence of pulmonary hypertension and may be used to estimate PAP.

Stability and Control of Tactical Missile Systems Held in Ankara (Turkey) on 9-12 May 1988

DTIC Science & Technology

1989-03-01

basic body for the systematic tests consisted of a cylindrical body with an ogive nose 3.0 calibers long for a total body length of 12.5 calibers A...Portance et stabilittd d’un Aiulege (ogies / iei 4 cylindre ) A N - 2.8. Compareison celcul "Euler" eec 1 d~~w~~hR~~t -- x~ine CALCUL -EULERV OPUP...toujours repr~sentatifs de Ia r~alit6. Compte tenu des pr~cisions recher- ch~es, lea effets du montage, d’un jet propulsif, du nombre de Reynolds, ou de

Development of a Cool Propellant for the 3 in./50 Caliber Gun. Development of a Cool Propellant for the 3 in./70 Caliber Gun. Development of Ignition Systems for the Cool Propellant Charges. Ballistic Test of Cool Propellants EX-6735, EX-6721 and IHPB-S-83C

DTIC Science & Technology

1951-06-09

HHMKHtffivfädMK fiösafe^.^., " -."- ; ji- ^ vrf •»£,. gyyrarfwaMHf^» i~ "& I •^ is\\!"* .!•,’•• .-••nj’’ ’ r.’ U St"-/s...34. <•-.-"- A.tttu Tseiinical Lite ,fü^-=^-<^ss> >,, -7 > ’" Commanding General, F^ank^ord^Arjsenal ._ Bridge and faCony Stree’t-s^.r^qr^—--- - Z

[Stripping of the external saphenous vein. Use of the Hall Chevallier stripper].

PubMed

Taieb-Birnbaum, W

1986-09-20

In more than 20 cases we used the Hall Chevallier stripper (initially devised to remove the valves of the internal saphenous vein in femoro-popliteal bypass) for stripping of the external saphenous vein. This routine procedure is not always easy to perform, owing to the irregular caliber of that vessel. There are three reasons why we used this particular stripper for this unusual purpose: its end is streamlined; strippers of different calibers are available and the instrument is rigid. In those exceptional cases where the external saphenous vein is not accessible from below (e.g. notably after sclerosis), stripping can be carried out from above.

Fabrication of Small Caliber Stent-grafts Using Electrospinning and Balloon Expandable Bare Metal Stents.

PubMed

Uthamaraj, Susheil; Tefft, Brandon J; Jana, Soumen; Hlinomaz, Ota; Kalra, Manju; Lerman, Amir; Dragomir-Daescu, Dan; Sandhu, Gurpreet S

2016-10-26

Stent-grafts are widely used for the treatment of various conditions such as aortic lesions, aneurysms, emboli due to coronary intervention procedures and perforations in vasculature. Such stent-grafts are manufactured by covering a stent with a polymer membrane. An ideal stent-graft should have a biocompatible stent covered by a porous, thromboresistant, and biocompatible polymer membrane which mimics the extracellular matrix thereby promoting injury site healing. The goal of this protocol is to manufacture a small caliber stent-graft by encapsulating a balloon expandable stent within two layers of electrospun polyurethane nanofibers. Electrospinning of polyurethane has been shown to assist in healing by mimicking native extracellular matrix, thereby promoting endothelialization. Electrospinning polyurethane nanofibers on a slowly rotating mandrel enabled us to precisely control the thickness of the nanofibrous membrane, which is essential to achieve a small caliber balloon expandable stent-graft. Mechanical validation by crimping and expansion of the stent-graft has shown that the nanofibrous polyurethane membrane is sufficiently flexible to crimp and expand while staying patent without showing any signs of tearing or delamination. Furthermore, stent-grafts fabricated using the methods described here are capable of being implanted using a coronary intervention procedure using standard size guide catheters.

A case of left inferior vena cava.

PubMed

Yano, R; Hayakawa, D; Emura, S; Chen, H; Ozawa, Y; Taguchi, H; Shoumura, S

2001-12-01

A case of left inferior vena cava (IVC) was found in a 72-year-old male cadaver during student dissection practice in 1999 at Gifu University School of Medicine. It was formed by junction of the left and right common iliac veins at the lower left corner of the 5th lumbar vertebra. This IVC (15-mm caliber) ascended 82 mm along the left side of the abdominal aorta dorsally to the ureter. Receiving the left renal vein, it became 21 mm in caliber and ran obliquely upward for 43 mm across the abdominal aorta. As soon as it received two right renal veins at the level of the 2nd lumbar vertebra, the IVC (25-mm caliber) turned directly above. The present case belongs to Type C of the classification of McClure and Butler (1925), which is based on the combinations of the left and right IVCs, and on their location relative to the ureters. The present case also belongs to Type 1 of the classification of Yoshida et al. (1981). We consider that left IVC in the present case is mainly caused by disappearance of the right supracardinal vein and persistence of the left one during the embryological development of the IVC.

Acute Effect of Foam Rolling and Dynamic Stretching on Flexibility and Jump Height.

PubMed

Smith, Jason C; Pridgeon, Brooke; Hall, MacGregor C

2018-04-04

Smith, JC, Pridgeon, B, and Hall, MC. Acute effect of foam rolling and dynamic stretching on flexibility and jump height. J Strength Cond Res XX(X): 000-000, 2017-Dynamic stretching (DS) can acutely improve vertical jump (VJ) performance but its effect lasts no more than 5 minutes. Foam rolling (FR), a form of self-myofascial release, can acutely increase range of motion (ROM) with this effect lasting less than 10 minutes. Therefore, the purpose of this study was to evaluate the time course of these effects, separately and combined, on VJ height and ROM. Twenty-nine university students completed 4 different sessions (control, FR, DS, and combo) in a randomized order. After a warm-up and baseline assessments of VJ height and sit-and-reach, participants rested (control) and performed FR, DS, and the combination of FR and DS (combo). Vertical jump height and ROM were assessed every 5 minutes for 20 minutes after treatment. Mean scores at each time point were expressed as a percent change from baseline scores. Immediately after FR, sit-and-reach was significantly greater than control (p = 0.003). Vertical jump height immediately after treatment for DS and combo was significantly greater than the control and FR counterparts (p ≤ 0.002). Vertical jump height for DS and combo was also significantly greater than the control counterpart at 5 minutes after treatment (p < 0.001). At 15 minutes after treatment, the percent change in VJ height for the combo was significantly greater than the control counterpart (p = 0.002). Although FR has no effect on VJ performance, it can acutely increase ROM, but its effect was quickly dissipated. Foam rolling does not seem to enhance VJ height either alone or in combination with DS.

Development of Advanced High Strength Steel for Improved Vehicle Safety, Fuel Efficiency and CO2 Emission

NASA Astrophysics Data System (ADS)

Kumar, Satendra; Singhai, Mrigandra; Desai, Rahul; Sam, Srimanta; Patra, Pradip Kumar

2016-10-01

Global warming and green house gas emissions are the major issues worldwide and their impacts are clearly visible as a record high temperatures, rising sea, and severe `flooding and droughts'. Motor vehicles considered as a major contributor on global warming due to its green house gas emissions. Hence, the automobile industries are under tremendous pressure from government and society to reduce green house gas emission to maximum possible extent. In present work, Dual Phase steel with boron as microalloying is manufactured using thermo-mechanical treatment during hot rolling. Dual phase steel with boron microalloying improved strength by near about 200 MPa than dual phase steel without boron. The boron added dual phase steel can be used for manufacturing stronger and a lighter vehicle which is expected to perform positively on green house gas emissions. The corrosion resistance behavior is also improved with boron addition which would further increase the life cycle of the vehicle even under corrosive atmosphere.

Effects of the Strain Rate and Temperature on the Microstructural Evolution of Twin-Rolled Cast Wrought AZ31B Alloys Sheets

NASA Astrophysics Data System (ADS)

Rodriguez, A. K.; Kridli, G.; Ayoub, G.; Zbib, H.

2013-10-01

This article investigates the effects of the strain rate and temperature on the microstructural evolution of twin-rolled cast wrought AZ31B sheets. This was achieved through static heating and through tensile test performed at strain rates from 10-4 to 10-1 s-1 and temperatures between room temperature (RT) and 300 °C. While brittle fracture with high stresses and limited elongation was observed at the RT, ductile behavior was obtained at higher temperatures with low strain rates. The strain rate sensitivity and activation energy calculations indicate that grain boundary diffusion and lattice diffusion are the two rate-controlling mechanisms at warm and high temperatures, respectively. An analysis of the evolution of the microstructure provided some indications of the most probable deformation mechanisms in the material: twinning operates at lower temperatures, and dynamic recrystallization dominates at higher temperatures. The static evolution of the microstructure was also studied, proving a gradual static grain growth of the AZ31B with annealing temperature and time.

Retinal vascular geometry in Asian persons with diabetes and retinopathy.

PubMed

Cheung, Carol Yim-lui; Lamoureux, Ecosse; Ikram, M Kamran; Sasongko, M Bayu; Ding, Jie; Zheng, Yingfeng; Mitchell, Paul; Wang, Jie Jin; Wong, Tien Yin

2012-05-01

Our purpose was to examine the relationship of retinal vascular parameters with diabetes and retinopathy in an older Asian population. Retinal photographs from participants of a population-based survey of Asian Malay persons aged 40-80 years were analyzed. Specific retinal vascular parameters (tortuosity, branching angle, fractal dimension, and caliber) were measured using a semiautomated computer-based program. Diabetes was defined as random plasma glucose ≥ 11.1 mmol/liter, the use of diabetes medication, or physician-diagnosed diabetes. Retinopathy signs were graded from photographs using the modified Airlie House classification system. A total of 2735 persons were included in the study. Persons with diabetes (n = 594) were more likely to have straighter (less tortuous) arterioles and wider arteriolar and venular caliber than those without diabetes (n = 2141). Among subjects with diabetes, those with retinopathy had wider venular caliber than those without retinopathy (211.3 versus 204.9 mm, p = .001). Among nondiabetic subjects, however, those with retinopathy had more tortuous venules than those without retinopathy [5.19(×10(4)) versus 4.27(×10(4)), p < .001]. Retinal vascular parameters varied by diabetes and retinopathy status in this older Asian cohort. Our findings suggest that subtle alterations in retinal vascular architecture are influenced by diabetes. © 2012 Diabetes Technology Society.

Fabrication of Small Caliber Stent-grafts Using Electrospinning and Balloon Expandable Bare Metal Stents

PubMed Central

Uthamaraj, Susheil; Tefft, Brandon J.; Jana, Soumen; Hlinomaz, Ota; Kalra, Manju; Lerman, Amir; Dragomir-Daescu, Dan; Sandhu, Gurpreet S.

2016-01-01

Stent-grafts are widely used for the treatment of various conditions such as aortic lesions, aneurysms, emboli due to coronary intervention procedures and perforations in vasculature. Such stent-grafts are manufactured by covering a stent with a polymer membrane. An ideal stent-graft should have a biocompatible stent covered by a porous, thromboresistant, and biocompatible polymer membrane which mimics the extracellular matrix thereby promoting injury site healing. The goal of this protocol is to manufacture a small caliber stent-graft by encapsulating a balloon expandable stent within two layers of electrospun polyurethane nanofibers. Electrospinning of polyurethane has been shown to assist in healing by mimicking native extracellular matrix, thereby promoting endothelialization. Electrospinning polyurethane nanofibers on a slowly rotating mandrel enabled us to precisely control the thickness of the nanofibrous membrane, which is essential to achieve a small caliber balloon expandable stent-graft. Mechanical validation by crimping and expansion of the stent-graft has shown that the nanofibrous polyurethane membrane is sufficiently flexible to crimp and expand while staying patent without showing any signs of tearing or delamination. Furthermore, stent-grafts fabricated using the methods described here are capable of being implanted using a coronary intervention procedure using standard size guide catheters. PMID:27805589

Microstructure of warm rolling and pearlitic transformation of ultrafine-grained GCr15 steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Jun-Jie; Lian, Fu-Liang; Liu, Hong-Ji

2014-09-15

Pearlitic transformation mechanisms have been investigated in ultra-fine grained GCr15 steel. The ultrafine-grained steel, whose grain size was less than 1 μm, was prepared by thermo-mechanical treatment at 873 K and then annealing at 923 K for 2 h. Pearlitic transformation was conducted by reheating the ultra-fine grained samples at 1073 K and 1123 K for different periods of time and then cooling in air. Scanning electron microscope observation shows that normal lamellar pearlite, instead of granular cementite and ferrite, cannot be formed when the grain size is approximately less than 4(± 0.6) μm, which yields a critical grain sizemore » for normal lamellar pearlitic transformations in this chromium alloyed steel. The result confirms that grain size has a great influence on pearlitic transformation by increasing the diffusion rate of carbon atoms in the ultra-fine grained steel, and the addition of chromium element doesn't change this pearlitic phase transformation rule. Meanwhile, the grain growth rate is reduced by chromium alloying, which is beneficial to form fine grains during austenitizing, thus it facilitating pearlitic transformation by divorced eutectoid transformation. Moreover, chromium element can form a relatively high gradient in the frontier of the undissolved carbide, which promotes carbide formation in the frontier of the undissolved carbide, i.e., chromium promotes divorced eutectoid transformation. - Highlights: • Ultrafine-grained GCr15 steel was obtained by warm rolling and annealing technology. • Reduction of grain size makes pearlite morphology from lamellar to granular. • Adding Cr does not change normal pearlitic phase transformation rule in UFG steel. • Cr carbide resists grain growth and facilitates pearlitic transformation by DET.« less

A system for automatic aorta sections measurements on chest CT

NASA Astrophysics Data System (ADS)

Pfeffer, Yitzchak; Mayer, Arnaldo; Zholkover, Adi; Konen, Eli

2016-03-01

A new method is proposed for caliber measurement of the ascending aorta (AA) and descending aorta (DA). A key component of the method is the automatic detection of the carina, as an anatomical landmark around which an axial volume of interest (VOI) can be defined to observe the aortic caliber. For each slice in the VOI, a linear profile line connecting the AA with the DA is found by pattern matching on the underlying intensity profile. Next, the aortic center position is found using Hough transform on the best linear segment candidate. Finally, region growing around the center provides an accurate segmentation and caliber measurement. We evaluated the algorithm on 113 sequential chest CT scans, slice thickness of 0.75 - 3.75mm, 90 with contrast agent injected. The algorithm success rates were computed as the percentage of scans in which the center of the AA was found. Automated measurements of AA caliber were compared with independent measurements of two experienced chest radiologists, comparing the absolute difference between the two radiologists with the absolute difference between the algorithm and each of the radiologists. The measurement stability was demonstrated by computing the STD of the absolute difference between the radiologists, and between the algorithm and the radiologists. Results: Success rates of 93% and 74% were achieved, for contrast injected cases and non-contrast cases, respectively. These results indicate that the algorithm can be robust in large variability of image quality, such as the cases in a realworld clinical setting. The average absolute difference between the algorithm and the radiologists was 1.85mm, lower than the average absolute difference between the radiologists, which was 2.1mm. The STD of the absolute difference between the algorithm and the radiologists was 1.5mm vs 1.6mm between the two radiologists. These results demonstrate the clinical relevance of the algorithm measurements.

Automatic detection and quantification of pulmonary arterio-venous malformations in hereditary hemorrhagic telangiectasia

NASA Astrophysics Data System (ADS)

Fetita, Catalin; Fortemps de Loneux, Thierry; Kouvahe, Amélé Florence; El Hajjam, Mostafa

2017-03-01

Hereditary hemorrhagic telangiectasia (HHT) is an autosomic dominant disorder, which is characterized by the development of multiple arterio-venous malformations in the skin, mucous membranes, and/or visceral organs. Pulmonary Arterio-Venous Malformation (PAVM) is an abnormal connection where feeding arteries shunt directly into draining veins with no intervening capillary bed. This condition may lead to paradoxical embolism and hemorrhagic complications. PAVMs patients should systematically be screened as the spontaneous complication rate is high, reaching almost 50%. Chest enhanced contrast CT scanner is the reference screening and follow-up examination. When performed by experienced operators as the prime treatment, percutaneous embolization of PAVMs is a safe, efficient and sustained therapy. The accuracy of PAVM detection and quantification of its progression over time is the key of embolotherapy success. In this paper, we propose an automatic method for PAVM detection and quantification relying on a modeling of vessel deformation, i.e. local caliber increase, based on mathematical morphology. The pulmonary field and vessels are first segmented using geodesic operators. The vessel caliber is estimated by means of a granulometric measure and the local caliber increase is detected by using a geodesic operator, the h-maxdomes. The detection sensitivity can be tuned up according to the choice of the h value which models the irregularity of the vessel caliber along its axis and the PAVM selection is performed according to a clinical criterion of >3 mm diameter of the feeding artery of the PAVM. The developed method was tested on a 20 patient dataset. A sensitivity study allowed choosing the irregularity parameter to maximize the true positive ratio reaching 85.4% in average. A specific false positive reduction procedure targeting the vessel trunks of the arterio-venous tree near mediastinum allows a precision increase from 13% to 67% with an average number of 1.15 false positives per scan.

N-Terminal Pro-B-Type Natriuretic Peptide Is Related to Retinal Microvascular Damage: The Rotterdam Study.

PubMed

Mutlu, Unal; Ikram, M Arfan; Hofman, Albert; de Jong, Paulus T V M; Klaver, Caroline C W; Ikram, M Kamran

2016-08-01

N-terminal pro-B-type natriuretic peptide (NT-proBNP) is a marker of cardiac dysfunction and has been linked to various indices of large vessel disease. However, it remains unclear whether NT-proBNP also relates to microvascular damage. In a community-dwelling population, we studied the association between NT-proBNP and retinal microvascular damage. From the population-based Rotterdam Study, we included 8437 participants (mean age 64.1 years and 59% women) without a history of cardiovascular disease, with NT-proBNP data and gradable retinal images. NT-proBNP serum levels were measured using an immunoassay. Retinopathy signs, that is, exudates, microaneurysms, cotton wool spots, and dot/blot hemorrhages, present on fundus photographs were graded in the total study population; retinal vascular calibers, that is, arteriolar and venular calibers, were semiautomatically measured in a subsample (n=2763) of the study population. We conducted cross-sectional analyses on the association between NT-proBNP and retinal microvascular damage using logistic and linear regression models, adjusting for age, sex, and cardiovascular risk factors. We found that NT-proBNP was associated with the presence of retinopathy (adjusted odds ratio [95% confidence interval] per SD increase in natural log-transformed NT-proBNP: 1.14 [1.03-1.27]). We also found that higher NT-proBNP was associated with narrower arteriolar calibers (adjusted mean difference in arteriolar caliber per SD increase in natural log-transformed NT-proBNP: -0.89 µm [-1.54 to -0.24]). This association remained unchanged after excluding participants with retinopathy signs. In participants free of clinical cardiovascular disease, higher levels of NT-proBNP are associated with retinal microvascular damage, suggesting a potential role for NT-proBNP as marker for small vessel disease. © 2016 American Heart Association, Inc.

Assessing the accuracy of using oscillating gradient spin echo sequences with AxCaliber to infer micron-sized axon diameters.

PubMed

Mercredi, Morgan; Vincent, Trevor J; Bidinosti, Christopher P; Martin, Melanie

2017-02-01

Current magnetic resonance imaging (MRI) axon diameter measurements rely on the pulsed gradient spin-echo sequence, which is unable to provide diffusion times short enough to measure small axon diameters. This study combines the AxCaliber axon diameter fitting method with data generated from Monte Carlo simulations of oscillating gradient spin-echo sequences (OGSE) to infer micron-sized axon diameters, in order to determine the feasibility of using MRI to infer smaller axon diameters in brain tissue. Monte Carlo computer simulation data were synthesized from tissue geometries of cylinders of different diameters using a range of gradient frequencies in the cosine OGSE sequence . Data were fitted to the AxCaliber method modified to allow the new pulse sequence. Intra- and extra-axonal water were studied separately and together. The simulations revealed the extra-axonal model to be problematic. Rather than change the model, we found that restricting the range of gradient frequencies such that the measured apparent diffusion coefficient was constant over that range resulted in more accurate fitted diameters. Thus a careful selection of frequency ranges is needed for the AxCaliber method to correctly model extra-axonal water, or adaptations to the method are needed. This restriction helped reduce the necessary gradient strengths for measurements that could be performed with parameters feasible for a Bruker BG6 gradient set. For these experiments, the simulations inferred diameters as small as 0.5 μm on square-packed and randomly packed cylinders. The accuracy of the inferred diameters was found to be dependent on the signal-to-noise ratio (SNR), with smaller diameters more affected by noise, although all diameter distributions were distinguishable from one another for all SNRs tested. The results of this study indicate the feasibility of using MRI with OGSE on preclinical scanners to infer small axon diameters.

Features of precision slot cutting with a large number of calibers using the radiation of a single-mode fiber laser

NASA Astrophysics Data System (ADS)

Vitshas, A. A.; Zelentsov, A. G.; Lopota, V. A.; Menakhin, V. P.; Panchenko, V. P.; Soroka, A. M.

2014-02-01

The results of the experimental and theoretical investigations aimed at determining the characteristics and features of precision slot cutting with a large number of calibers in sheets of low-carbon steel using the radiation of a single-mode fiber laser with pulse power up to 1 kW are presented. The description of the experimental installation, performance conditions of investigations, and variable parameters are described. Precision cutting of low-carbon steel up to 10 mm with the number of calibers ranging from 30 to 70 at a slot width of ≈60 μm is performed for the first time. Such cutting occurs only in the pulsed-periodic mode using single-mode radiation with a pulse duration of 2-3 ms, a pulse ratio of 2-4, and oxygen, whose influence differs in principle both in various cut regions over the sheet thickness and from cutting with a CO2 laser. The cutting velocity (100-50 mm/min) of sheet steel up to thicknesses of 10 mm with deep channeling, roughness parameters, hardness of the cut surface, which insignificantly (by ≈20%) exceeds the hardness of untreated steel, the phase structure of steel, and the scales of their varying inside metal are measured. The efficiency (≈3%) of precision cutting and the efficiency of transportation of radiation (25%) in large-caliber slot orifices in the "waveguide" mode are determined by the experimental data. The useful specific energy contribution of the laser radiation is w l = N l/( hbv) ≈ 2 × 1012 J/m2 for all studied thicknesses of sheet samples accurate to 20%. A qualitative model of the laser-oxygen precision cutting with deep channeling, which explains the cyclic and interrupting character of cutting and necessity of using oxygen as the cutting gas, is proposed.

VAGINOPLASTY WITH AUTOLOGOUS BUCCAL MUCOSA FENESTRATED GRAFT IN TWO PATIENTS WITH VAGINAL AGENESIS: A MULTIDISCIPLINARY APPROACH AND LITERATURE REVIEW

PubMed Central

Chan, Jessica L; Levin, Pamela J; Ford, Brian P; Stanton, David C; Pfeifer, Samantha M

2017-01-01

The objective of this case series is to describe the procedure and outcomes of a multidisciplinary approach to vaginoplasty using autologous buccal mucosa fenestrated grafts in two patients with vaginal agenesis. This procedure resulted in anatomic success with a functional neovagina with good vaginal length and caliber and satisfactory sexual function capacity and well healed buccal mucosa. There were no complications and patients were satisfied with surgical results. We conclude that the use of a single fenestrated graft of autologous buccal mucosa is a simple, effective procedure for the treatment of vaginal agenesis that results in an optimally functioning neovagina with respect to vaginal length, caliber, and sexual capacity. PMID:28212868

A Tale of Two Hemispheres: Field Studies of Aerosols and Marine Stratocumulus Clouds (451st Brookhaven Lecture)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Yin-Nan

2009-05-13

By reflecting sunlight, clouds may be mitigating the warming effect of greenhouse gases in the Earth's atmosphere. To discuss the roll that aerosol particles play in the cooling mechanism of clouds, Chemist Yin-Nan Lee of the Atmospheric Sciences Division of the Environmental Sciences Department will discuss “A Tale of Two Hemispheres: Field Studies of Aerosols and Marine Stratocumulus Clouds” during the 451st Brookhaven Lecture, beginning 4 p.m. on Wednesday 13 May in Berkner Hall. During his lecture, Dr. Lee will discuss his findings from collaborative studies of stratocumulus clouds over the coastal waters of California and Chile.

An on-ice measurement approach to analyse the biomechanics of ice hockey skating.

PubMed

Buckeridge, Erica; LeVangie, Marc C; Stetter, Bernd; Nigg, Sandro R; Nigg, Benno M

2015-01-01

Skating is a fundamental movement in ice hockey; however little research has been conducted within the field of hockey skating biomechanics due to the difficulties of on-ice data collection. In this study a novel on-ice measurement approach was tested for reliability, and subsequently implemented to investigate the forward skating technique, as well as technique differences across skill levels. Nine high caliber (High) and nine low caliber (Low) hockey players performed 30 m forward skating trials. A 3D accelerometer was mounted to the right skate for the purpose of stride detection, with the 2nd and 6th strides defined as acceleration and steady-state, respectively. The activity of five lower extremity muscles was recorded using surface electromyography. Biaxial electro-goniometers were used to quantify hip and knee angles, and in-skate plantar force was measured using instrumented insoles. Reliability was assessed with the coefficient of multiple correlation, which demonstrated moderate (r>0.65) to excellent (r>0.95) scores across selected measured variables. Greater plantar-flexor muscle activity and hip extension were evident during acceleration strides, while steady state strides exhibited greater knee extensor activity and hip abduction range of motion (p<0.05). High caliber exhibited greater hip range of motion and forefoot force application (p<0.05). The successful implementation of this on-ice mobile measurement approach offers potential for athlete monitoring, biofeedback and training advice.

Noise exposure assessment and abatement strategies at an indoor firing range.

PubMed

Kardous, Chucri A; Willson, Robert D; Hayden, Charles S; Szlapa, Piotr; Murphy, William J; Reeves, Efrem R

2003-08-01

Exposure to hazardous impulse noise is common during the firing of weapons at indoor firing ranges. The aims of this study were to characterize the impulse noise environment at a law enforcement firing range; document the insufficiencies found at the range from a health and safety standpoint; and provide noise abatement recommendations to reduce the overall health hazard to the auditory system. Ten shooters conducted a typical live-fire exercise using three different weapons--the Beretta.40 caliber pistol, the Remington.308 caliber shotgun, and the M4.223 caliber assault rifle. Measurements were obtained at 12 different positions throughout the firing range and adjacent areas using dosimeters and sound level meters. Personal and area measurements were recorded to a digital audio tape (DAT) recorder for further spectral analysis. Peak pressure levels inside the firing range reached 163 decibels (dB) in peak pressure. Equivalent sound levels (Leq) ranged from 78 decibels, A-weighted (dBA), in office area adjacent to the range to 122 dBA inside the range. Noise reductions from wall structures ranged from 29-44 dB. Noise abatement strategies ranged from simple noise control measures (such as sealing construction joints and leaks) to elaborate design modifications to eliminate structural-borne sounds using acoustical treatments. Further studies are needed to better characterize the effects of firing weapons in enclosed spaces on hearing and health in general.

The relationship between aortic stiffness and changes in retinal microvessels among Asian ischemic stroke patients.

PubMed

De Silva, D A; Woon, F-P; Manzano, J J F; Liu, E Y; Chang, H-M; Chen, C; Wang, J J; Mitchell, P; Kingwell, B A; Cameron, J D; Lindley, R I; Wong, T Y; Wong, M-C

2012-12-01

Large-artery stiffness is a risk factor for stroke, including cerebral small-vessel disease. Retinal microvascular changes are thought to mirror those in cerebral microvessels. We investigated the relationship between aortic stiffness and retinal microvascular changes in Asian ischemic stroke patients. We studied 145 acute ischemic stroke patients in Singapore who had aortic stiffness measurements using carotid-femoral pulse wave velocity (cPWV). Retinal photographs were assessed for retinal microvessel caliber and qualitative signs of focal arteriolar narrowing, arteriovenous nicking and enhanced arteriolar light reflex. Aortic stiffening was associated with retinal arteriolar changes. Retinal arteriolar caliber decreased with increasing cPWV (r=-0.207, P=0.014). After adjusting for age, gender, hypertension, diabetes, mean arterial pressure and small-vessel stroke subtype, patients within the highest cPWV quartile were more likely to have generalized retinal arteriolar narrowing defined as lowest caliber tertile (odds ratio (OR) 6.84, 95% confidence interval (CI) 1.45-32.30), focal arteriolar narrowing (OR 13.85, CI 1.82-105.67), arteriovenous nicking (OR 5.08, CI 1.12-23.00) and enhanced arteriolar light reflex (OR 3.83, CI 0.89-16.48), compared with those within the lowest quartile. In ischemic stroke patients, aortic stiffening is associated with retinal arteriolar luminal narrowing as well as features of retinal arteriolosclerosis.

A Miniaturized Magnetic Induction Sensor Using Geomagnetism for Turn Count of Small-Caliber Ammunition

PubMed Central

Yoon, Sang-Hee; Lee, Seok-Woo; Lee, Young-Ho; Oh, Jong-Soo

2006-01-01

This paper presents a miniaturized magnetic induction sensor (MMIS), where geomagnetism and high rpm rotation of ammunition are used to detect the turn number of the ammunition for applications to small-caliber turn-counting fuzes. The MMIS, composed of cores and a coil, has a robust structure without moving parts to increase the shock survivability in a gunfire environment of ∼30,000 g's. The MMIS is designed and fabricated on the basis of the simulation results of an electromagnetic analysis tool, Maxwell® 3D. In the experimental study, static MMIS test using a solenoid-coil apparatus and dynamic MMIS test (firing test) have been made. The present MMIS has shown that an induction voltage of 6.5 mVp-p is generated at a magnetic flux density of 0.05 mT and a rotational velocity of 30,000 rpm. From the measured signal, MMIS has shown a signal-to-noise ratio of 44.0 dB, a nonlinearity of 0.59%, a frequency-normalized sensitivity of 0.256±0.010 V/T·Hz and a drift of 0.27% in the temperature range of -30∼+43°C. Firing test has shown that the MMIS can be used as a turn-counting sensor for small-caliber ammunition, verifying the shock survivability of the MMIS in a high-g environment.

An On-Ice Measurement Approach to Analyse the Biomechanics of Ice Hockey Skating

PubMed Central

Buckeridge, Erica; LeVangie, Marc C.; Stetter, Bernd; Nigg, Sandro R.; Nigg, Benno M.

2015-01-01

Skating is a fundamental movement in ice hockey; however little research has been conducted within the field of hockey skating biomechanics due to the difficulties of on-ice data collection. In this study a novel on-ice measurement approach was tested for reliability, and subsequently implemented to investigate the forward skating technique, as well as technique differences across skill levels. Nine high caliber (High) and nine low caliber (Low) hockey players performed 30m forward skating trials. A 3D accelerometer was mounted to the right skate for the purpose of stride detection, with the 2nd and 6th strides defined as acceleration and steady-state, respectively. The activity of five lower extremity muscles was recorded using surface electromyography. Biaxial electro-goniometers were used to quantify hip and knee angles, and in-skate plantar force was measured using instrumented insoles. Reliability was assessed with the coefficient of multiple correlation, which demonstrated moderate (r>0.65) to excellent (r>0.95) scores across selected measured variables. Greater plantar-flexor muscle activity and hip extension were evident during acceleration strides, while steady state strides exhibited greater knee extensor activity and hip abduction range of motion (p<0.05). High caliber exhibited greater hip range of motion and forefoot force application (p<0.05). The successful implementation of this on-ice mobile measurement approach offers potential for athlete monitoring, biofeedback and training advice. PMID:25973775

Using 3D printed models for planning and guidance during endovascular intervention: a technical advance.

PubMed

Itagaki, Michael W

2015-01-01

Three-dimensional (3D) printing applications in medicine have been limited due to high cost and technical difficulty of creating 3D printed objects. It is not known whether patient-specific, hollow, small-caliber vascular models can be manufactured with 3D printing, and used for small vessel endoluminal testing of devices. Manufacture of anatomically accurate, patient-specific, small-caliber arterial models was attempted using data from a patient's CT scan, free open-source software, and low-cost Internet 3D printing services. Prior to endovascular treatment of a patient with multiple splenic artery aneurysms, a 3D printed model was used preoperatively to test catheter equipment and practice the procedure. A second model was used intraoperatively as a reference. Full-scale plastic models were successfully produced. Testing determined the optimal puncture site for catheter positioning. A guide catheter, base catheter, and microcatheter combination selected during testing was used intraoperatively with success, and the need for repeat angiograms to optimize image orientation was minimized. A difficult and unconventional procedure was successful in treating the aneurysms while preserving splenic function. We conclude that creation of small-caliber vascular models with 3D printing is possible. Free software and low-cost printing services make creation of these models affordable and practical. Models are useful in preoperative planning and intraoperative guidance.

Use of agar/glycerol and agar/glycerol/water as a translucent brain simulant for ballistic testing.

PubMed

Falland-Cheung, Lisa; Waddell, J Neil; Lazarjan, Milad Soltanipour; Jermy, Mark C; Winter, Taylor; Tong, Darryl; Brunton, Paul A

2017-01-01

The suitability of agar/glycerol/water and agar/glycerol mixtures as brain simulants was investigated. Test specimens (n=15) (50x27×37mm) were fabricated for these different mixtures and conditioned to 12°C, 22°C, and 26°C prior to testing. For comparison, fresh deer brain specimens (n=20) were sourced and prepared to the same dimensions as the agar/glycerol(/water) mixtures and conditioned to 12°C and 37°C. High impact tests were carried out with a 0.22-caliber air rifle pellet and a high-speed camera was used to record the projectile as it passed through the specimens, allowing for energy loss and vertical displacement velocity calculation. Although the agar/glycerol/water mixture presented with similar vertical expansion and contraction of the specimens to the warm and cold deer brains, a two-fold decrease of the vertical expansion and contraction was noticed with the agar/glycerol specimens. Also considerably less extrusion of this mixture out of the exit and entry sides after specimen penetration was observed. Of the simulants tested, agar/glycerol/water was the most suitable brain simulant for ballistic testing and impact studies. Copyright © 2016 Elsevier Ltd. All rights reserved.

Teaching the principles of statistical dynamics.

PubMed

Ghosh, Kingshuk; Dill, Ken A; Inamdar, Mandar M; Seitaridou, Effrosyni; Phillips, Rob

2006-02-01

We describe a simple framework for teaching the principles that underlie the dynamical laws of transport: Fick's law of diffusion, Fourier's law of heat flow, the Newtonian viscosity law, and the mass-action laws of chemical kinetics. In analogy with the way that the maximization of entropy over microstates leads to the Boltzmann distribution and predictions about equilibria, maximizing a quantity that E. T. Jaynes called "caliber" over all the possible microtrajectories leads to these dynamical laws. The principle of maximum caliber also leads to dynamical distribution functions that characterize the relative probabilities of different microtrajectories. A great source of recent interest in statistical dynamics has resulted from a new generation of single-particle and single-molecule experiments that make it possible to observe dynamics one trajectory at a time.

An implementation of the maximum-caliber principle by replica-averaged time-resolved restrained simulations

NASA Astrophysics Data System (ADS)

Capelli, Riccardo; Tiana, Guido; Camilloni, Carlo

2018-05-01

Inferential methods can be used to integrate experimental informations and molecular simulations. The maximum entropy principle provides a framework for using equilibrium experimental data, and it has been shown that replica-averaged simulations, restrained using a static potential, are a practical and powerful implementation of such a principle. Here we show that replica-averaged simulations restrained using a time-dependent potential are equivalent to the principle of maximum caliber, the dynamic version of the principle of maximum entropy, and thus may allow us to integrate time-resolved data in molecular dynamics simulations. We provide an analytical proof of the equivalence as well as a computational validation making use of simple models and synthetic data. Some limitations and possible solutions are also discussed.

An implementation of the maximum-caliber principle by replica-averaged time-resolved restrained simulations.

PubMed

Capelli, Riccardo; Tiana, Guido; Camilloni, Carlo

2018-05-14

Inferential methods can be used to integrate experimental informations and molecular simulations. The maximum entropy principle provides a framework for using equilibrium experimental data, and it has been shown that replica-averaged simulations, restrained using a static potential, are a practical and powerful implementation of such a principle. Here we show that replica-averaged simulations restrained using a time-dependent potential are equivalent to the principle of maximum caliber, the dynamic version of the principle of maximum entropy, and thus may allow us to integrate time-resolved data in molecular dynamics simulations. We provide an analytical proof of the equivalence as well as a computational validation making use of simple models and synthetic data. Some limitations and possible solutions are also discussed.

Modelling the impact of altered axonal morphometry on the response of regenerative nervous tissue to electrical stimulation through macro-sieve electrodes.

PubMed

Zellmer, Erik R; MacEwan, Matthew R; Moran, Daniel W

2018-04-01

Regenerated peripheral nervous tissue possesses different morphometric properties compared to undisrupted nerve. It is poorly understood how these morphometric differences alter the response of the regenerated nerve to electrical stimulation. In this work, we use computational modeling to explore the electrophysiological response of regenerated and undisrupted nerve axons to electrical stimulation delivered by macro-sieve electrodes (MSEs). A 3D finite element model of a peripheral nerve segment populated with mammalian myelinated axons and implanted with a macro-sieve electrode has been developed. Fiber diameters and morphometric characteristics representative of undisrupted or regenerated peripheral nervous tissue were assigned to core conductor models to simulate the two tissue types. Simulations were carried out to quantify differences in thresholds and chronaxie between undisrupted and regenerated fiber populations. The model was also used to determine the influence of axonal caliber on recruitment thresholds for the two tissue types. Model accuracy was assessed through comparisons with in vivo recruitment data from chronically implanted MSEs. Recruitment thresholds of individual regenerated fibers with diameters  >2 µm were found to be lower compared to same caliber undisrupted fibers at electrode to fiber distances of less than about 90-140 µm but roughly equal or higher for larger distances. Caliber redistributions observed in regenerated nerve resulted in an overall increase in average recruitment thresholds and chronaxie during whole nerve stimulation. Modeling results also suggest that large diameter undisrupted fibers located close to a longitudinally restricted current source such as the MSE have higher average recruitment thresholds compared to small diameter fibers. In contrast, large diameter regenerated nerve fibers located in close proximity of MSE sites have, on average, lower recruitment thresholds compared to small fibers. Utilizing regenerated fiber morphometry and caliber distributions resulted in accurate predictions of in vivo recruitment data. Our work uses computational modeling to show how morphometric differences between regenerated and undisrupted tissue results in recruitment threshold discrepancies, quantifies these differences, and illustrates how large undisrupted nerve fibers close to longitudinally restricted current sources have higher recruitment thresholds compared to adjacently positioned smaller fibers while the opposite is true for large regenerated fibers.

Modelling the impact of altered axonal morphometry on the response of regenerative nervous tissue to electrical stimulation through macro-sieve electrodes

NASA Astrophysics Data System (ADS)

Zellmer, Erik R.; MacEwan, Matthew R.; Moran, Daniel W.

2018-04-01

Objective. Regenerated peripheral nervous tissue possesses different morphometric properties compared to undisrupted nerve. It is poorly understood how these morphometric differences alter the response of the regenerated nerve to electrical stimulation. In this work, we use computational modeling to explore the electrophysiological response of regenerated and undisrupted nerve axons to electrical stimulation delivered by macro-sieve electrodes (MSEs). Approach. A 3D finite element model of a peripheral nerve segment populated with mammalian myelinated axons and implanted with a macro-sieve electrode has been developed. Fiber diameters and morphometric characteristics representative of undisrupted or regenerated peripheral nervous tissue were assigned to core conductor models to simulate the two tissue types. Simulations were carried out to quantify differences in thresholds and chronaxie between undisrupted and regenerated fiber populations. The model was also used to determine the influence of axonal caliber on recruitment thresholds for the two tissue types. Model accuracy was assessed through comparisons with in vivo recruitment data from chronically implanted MSEs. Main results. Recruitment thresholds of individual regenerated fibers with diameters  >2 µm were found to be lower compared to same caliber undisrupted fibers at electrode to fiber distances of less than about 90-140 µm but roughly equal or higher for larger distances. Caliber redistributions observed in regenerated nerve resulted in an overall increase in average recruitment thresholds and chronaxie during whole nerve stimulation. Modeling results also suggest that large diameter undisrupted fibers located close to a longitudinally restricted current source such as the MSE have higher average recruitment thresholds compared to small diameter fibers. In contrast, large diameter regenerated nerve fibers located in close proximity of MSE sites have, on average, lower recruitment thresholds compared to small fibers. Utilizing regenerated fiber morphometry and caliber distributions resulted in accurate predictions of in vivo recruitment data. Significance. Our work uses computational modeling to show how morphometric differences between regenerated and undisrupted tissue results in recruitment threshold discrepancies, quantifies these differences, and illustrates how large undisrupted nerve fibers close to longitudinally restricted current sources have higher recruitment thresholds compared to adjacently positioned smaller fibers while the opposite is true for large regenerated fibers.

Surgical Treatment of Anal Stenosis with Diamond Flap Anoplasty Performed in a Calibrated Fashion.

PubMed

Gülen, Merter; Leventoğlu, Sezai; Ege, Bahadir; Menteş, B Bülent

2016-03-01

Regarding anoplasty for anal stenosis, it is not clear to what extent the final anal caliber should be targeted. The aim of this study was to investigate the results of diamond-flap anoplasty performed in a calibrated manner for the treatment of severe anal stenosis due to a previous hemorrhoidectomy. Prospectively prepared standard forms were evaluated retrospectively. Anoplasty with unilateral or bilateral diamond flaps was performed for moderate or severe anal stenosis, targeting a final anal caliber of 25 to 26 mm. The demographic characteristics, causes of anal stenosis, number of previous surgeries, anal stenosis staging (Milsom and Mazier), anal calibers (millimeter), the Cleveland Clinic Incontinence Score, and the modified obstructed defecation syndrome Longo score were recorded on pre-prepared standard forms, as well as postoperative complications and the time of return to work. From January 2011 to July 2013, 18 patients (12 males, 67%) with a median age of 39 years (range, 27-70) were treated. All of the patients had a history of previous hemorrhoidectomy. The number of previous corrective interventions was 2.1 ± 1.8 (range, 0-4), and 2 patients had a history of failed anoplasty. Five patients (28%) had moderate anal stenosis and 13 (72%) had severe anal stenosis. Preoperative, intraoperative, and 12-month postoperative anal calibration values were 9 ± 3 mm (range, 5-15), 25 ± 0.75 mm (range, 24-26), and 25 ± 1 mm (range, 23-27) (p < 0.0001, for immediate postoperative and 12-month postoperative anal calibers compared with the intraoperative). Preoperative and 12-month postoperative Cleveland Clinic Incontinence Scores were 0.83 ± 1.15 (range, 0-4) and 0.39 ± 0.70 (range, 0-2) (p = 1.0). The clinical success rate was 88.9%. No severe postoperative complications were observed. This study was limited because it was a single-armed, retrospective analysis of prospectively designed data. Diamond-flap anoplasty performed in a standardized and calibrated manner is a highly successful method for the treatment of anal stenosis caused by previous hemorrhoidectomy.

Monte Carlo modeling of recrystallization processes in α-uranium

DOE PAGES

Steiner, M. A.; McCabe, R. J.; Garlea, E.; ...

2017-08-01

In this study, starting with electron backscattered diffraction (EBSD) data obtained from a warm clock-rolled α-uranium deformation microstructure, a Potts Monte Carlo model was used to simulate static site-saturated recrystallization while testing a number of different conditions for the assignment of recrystallized nuclei within the microstructure. The simulations support observations that recrystallized nuclei within α-uranium form preferentially on non-twin high-angle grain boundary sites at 450 °C, and demonstrate that the most likely nucleation sites on these boundaries can be identified by the surrounding degree of Kernel Average Misorientation (KAM), which may be considered as a proxy for the local geometricallymore » necessary dislocation (GND) density.« less

Small caliber guided projectile

DOEpatents

Jones, James F [Albuquerque, NM; Kast, Brian A [Albuquerque, NM; Kniskern, Marc W [Albuquerque, NM; Rose, Scott E [Albuquerque, NM; Rohrer, Brandon R [Albuquerque, NM; Woods, James W [Albuquerque, NM; Greene, Ronald W [Albuquerque, NM

2010-08-24

A non-spinning projectile that is self-guided to a laser designated target and is configured to be fired from a small caliber smooth bore gun barrel has an optical sensor mounted in the nose of the projectile, a counterbalancing mass portion near the fore end of the projectile and a hollow tapered body mounted aft of the counterbalancing mass. Stabilizing strakes are mounted to and extend outward from the tapered body with control fins located at the aft end of the strakes. Guidance and control electronics and electromagnetic actuators for operating the control fins are located within the tapered body section. Output from the optical sensor is processed by the guidance and control electronics to produce command signals for the electromagnetic actuators. A guidance control algorithm incorporating non-proportional, "bang-bang" control is used to steer the projectile to the target.

Comparison of the class and individual characteristics of Turkish 7.65 mm Browning/.32 Automatic caliber self-loading pistols with consecutive serial numbers.

PubMed

Sarıbey, Aylin Yalçin; Hannam, Abigail Grace

2013-01-01

Firearms identification is based on the fundamental principle that it is impossible to manufacture two identical items at the microscopic level. As firearm manufacturing technologies and quality assurance are improving, it is necessary to continually challenge this principle. In this study, two different makes of 7.65 mm Browning/.32 Automatic caliber self-loading pistols of Turkish manufacture were selected and examined. Ten pistols with consecutive serial numbers were examined and each fired 10 times. The fired cartridge cases were recovered for comparison purposes. It was found that for each make of pistol, the individual characteristics within the firing pin impression, ejector, and breech face marks of all 10 pistols were found to be significantly different. © 2012 American Academy of Forensic Sciences.

High-precision processing and detection of the high-caliber off-axis aspheric mirror

NASA Astrophysics Data System (ADS)

Dai, Chen; Li, Ang; Xu, Lingdi; Zhang, Yingjie

2017-10-01

To achieve the efficient, controllable, digital processing and high-precision detection of the high-caliber off-axis aspheric mirror, meeting the high-level development needs of the modern high-resolution, large field of space optical remote sensing camera, we carried out the research on high precision machining and testing technology of off-axis aspheric mirror. First, we forming the off-axis aspheric sample with diameter of 574mm × 302mm by milling it with milling machine, and then the intelligent robot equipment was used for off-axis aspheric high precision polishing. Surface detection of the sample will be proceed with the off-axis aspheric contact contour detection technology and offaxis non-spherical surface interference detection technology after its fine polishing using ion beam equipment. The final surface accuracy RMS is 12nm.

[Morphology of bullet wounds when using police ammunition, type QD-P.E.P].

PubMed

Stein, Kirsten Marion; Wagner, Thomas; Ain, Stephan

2006-01-01

6 years after introduction of the police ammunition QD-P.E.P. (9 mm caliber), 9 bullet wounds are presented from forensic investigations along with the results of experimental shots at pig carcasses. The evaluation reveals the characteristic pattern of such bullet wounds: a skin defect which is almost as large as the caliber and has a sharp-edged border thus looking like it has been punched out; the contusion ring ("abrasion ring") is conspicuously narrow. These findings can be explained by the shape and design of the projectile. In regular police work immediate incapacitation has not always been achieved, depending on the entry location of the bullet. Experimental shots at pig carcasses showed that in the case of shots at extremities, the residual energy of the exiting bullet may be sufficient to generate another penetrating bullet wound.

The vascular nature of hemorrhoids.

PubMed

Aigner, Felix; Bodner, Gerd; Gruber, Hannes; Conrad, Friedrich; Fritsch, Helga; Margreiter, Raimund; Bonatti, Hugo

2006-01-01

The arterial blood supply of the internal hemorrhoidal plexus is commonly believed to be associated with the pathogenesis of hemorrhoids. Ultrasound-supported proctoscopic techniques with Doppler-guided ligature of submucosal rectal arteries have been introduced for the therapy of hemorrhoids. The present investigation focuses on caliber and flow changes of the terminal branches of the superior rectal artery (SRA) supplying the corpus cavernosum recti (CCR) in patients with hemorrhoids. Forty-one outpatients (17 female, 24 male; mean age 48 years) with hemorrhoids of Goligher grades I-IV were compared with 17 healthy volunteers (nine female, eight male; mean age 29 years) by means of transperineal color Doppler ultrasound. The mean caliber of the arterial branches in the study group with hemorrhoids was 1.87 +/- 0.68 mm (range, 0.6 to 3.60 mm) and 0.92 +/- 0.15 mm (range, 0.6 to 1.2 mm) in the control group (P < 0.001). The arterial blood flow was significantly higher in patients with hemorrhoids than in the control group (mean 33.9 vs. 11.9 cm/second, P < 0.01). Our findings demonstrate that increased caliber and arterial blood flow of the terminal branches of the SRA are correlated with the appearance of hemorrhoids. We suggest that the hypervascularization of the anorectum contributes to the growth of hemorrhoids rather than being a consequence of hemorrhoids. Transperineal color Doppler ultrasound (CDUS) is an appropriate method to assess these findings in patients with hemorrhoids.

One-stoma carinoplasty: right upper sleeve lobectomy with hemicarinectomy for resection of right-tracheobronchial-angle tumors.

PubMed

Kaya, Seyda Ors; Sevinc, Serpil; Ceylan, Kenan Can; Usluer, Ozan; Unsal, Saban

2013-01-01

Tracheobronchial-angle tumors involve the right main bronchus, the right upper lobar bronchus, and the lateral wall of the lower trachea. Resecting these tumors is one of the most complex procedures in thoracic surgery. In cases of high-caliber mismatch, the selection of a suitable anastomotic technique can be challenging. We found that our use of a one-stoma carinoplasty technique overcame high-caliber mismatch after the resection of these tumors. From 2009 through 2012, 8 men (mean age, 59 ± 6.2 yr; range, 46-66 yr) underwent complete resection of non-small-cell right-tracheobronchial-angle tumors at our institution. In every case, right upper sleeve lobectomy, wedge carinal resection, and one-stoma carinoplasty were applied. After tumor resection, one patient with hemoptysis and bronchopleural fistula underwent a completion pneumonectomy and died 10 days postoperatively. Bronchoscopy was necessary in 2 patients who had atelectasis in the contralateral lung. At a mean follow-up duration of 19.43 ± 8.4 months (range, 0.2-27.1 mo), 6 patients were alive and free of disease. We conclude that our one-stoma carinoplasty technique enables the resection of tumors at the right tracheobronchial angle, with acceptable morbidity and mortality rates. This method saves the unaffected part of the ipsilateral lung and can overcome high-caliber mismatch. Because of these and other advantages, we suggest that using our method first might preclude having to perform a right carinal sleeve pneumonectomy or using Barclay's method.

A balloon-expandable sheath facilitates transfemoral TAVR in patients with peripheral vascular disease and tortuosity.

PubMed

Goldsweig, Andrew M; Faheem, Osman; Cleman, Michael W; Forrest, John K

2015-06-01

We sought to perform transcatheter aortic valve replacement (TAVR) via the transfemoral approach in patients with peripheral arterial disease (PAD), small caliber ileofemoral vessels and vascular tortuosity. For patients with increased surgical risk, TAVR is associated with a higher 1-year survival rate than surgical aortic valve replacement (SAVR). Transfemoral vascular access for TAVR results in superior outcomes versus procedures performed via other routes in terms of mortality, morbidity and healthcare economics. In many patients, the ability to safely perform the procedure via the transfemoral approach is limited by narrow, diseased and tortuous ileofemoral vasculature. We employed the SoloPath Balloon Expandable TransFemoral Access System (Terumo Med. Corp., Tokyo, Japan) to perform transfemoral TAVR in five patients with PAD, small caliber ileofemoral vessels and vascular tortuosity. We report our experience using this balloon-expandable sheath during 5 cases of transfemoral TAVR in patients with inhospitable ileofemoral vasculature of mean diameter ⩽ 5.8 mm. The unexpanded sheath's malleable structure and hydrophilic coating permitted deployment despite severe stenoses and tortuosity. Subsequent inflation to 18 Fr facilitated successful TAVR. Postprocedural angiography demonstrated no significant vascular access complications. In one case, the entire procedure was performed percutaneously, without common femoral artery surgical cutdown. The SoloPath sheath system permits transfemoral TAVR in patients with PAD small caliber ileofemoral vessels and vascular tortuosity. The transfemoral balloon-expandable sheath allowed these patients to avoid the increased morbidity and mortality risks associated with direct aortic or transapical access. © The Author(s), 2015.

Intrapulmonary vascular remodeling: MSCT-based evaluation in COPD and alpha-1 antitrypsin deficient subjects

NASA Astrophysics Data System (ADS)

Crosnier, Adeline; Fetita, Catalin; Thabut, Gabriel; Brillet, Pierre-Yves

2016-03-01

Whether COPD is generally known as a small airway disease, recent investigations suggest that vascular remodeling could play a key role in disease progression. This paper develops a specific investigation framework in order to evaluate the remodeling of the intrapulmonary vascular network and its correlation with other image or clinical parameters (emphysema score or FEV1) in patients with smoking- or genetic- (alpha-1 antitrypsin deficiency - AATD) related COPD. The developed approach evaluates the vessel caliber distribution per lung or lung region (upper, lower, 10%- and 20%- periphery) in relation with the severity of the disease and computes a remodeling marker given by the area under the caliber distribution curve for radii less than 1.6mm, AUC16. It exploits a medial axis analysis in relation with local caliber information computed in the segmented vascular network, with values normalized with respect to the lung volume (for which a robust segmentation is developed). The first results obtained on a 34-patient database (13 COPD, 13 AATD and 8 controls) showed significant vascular remodeling for COPD and AATD versus controls, with a negative correlation with the emphysema degree for COPD, but not for AATD. Significant vascular remodeling at 20% lung periphery was found both for the severe COPD and AATD patients, but not for the moderate groups. Also the vascular remodeling in AATD did not correlate with the FEV1, nor with DLCO, which might suggest independent mechanisms for bronchial and vascular remodeling in the lung.

Structural expression of a rolling hinge in the footwall of the Brenner Line normal fault, eastern Alps

NASA Astrophysics Data System (ADS)

Axen, Gary J.; Bartley, John M.; Selverstone, Jane

1995-12-01

The kinematic and temporal sequence of structures observed to overprint mylonites along the Brenner Line low-angle normal fault may record passage of the footwall through two rolling hinges, at the top and bottom of a ramp in the shear zone. The structures comprise west down brittle and brittle-ductile structures and east down brittle structures. PT conditions of formation (250° to >400°C and 2-23 km depth), obtained from analysis of oriented fluid inclusion planes, indicate that west down structures were formed at greater depths and temperatures, and therefore earlier, than the east down structures. These data suggest that the brittle structures formed under conditions that permit crystal-plastic deformation at long-term geologic strain rates and therefore probably reflect transient rapid strain rates and/or high fluid pressure. Structures inferred to have formed at a lower hinge are consistent with viscous flow models of rolling-hinge deformation and support the concept of a crustal asthenosphere. Such high temperatures at shallow crustal depth also suggest significant upward advection of heat by extensional unroofing of warm rocks, which may have reduced the flexural rigidity of the footwall and thus affected mechanical behavior at the upper rolling hinge. Exposed mylonitic foliation within a few hundred meters of the Brenner line and on top of the east-west trending anticlines in the footwall dips ˜15° west. Our data favor a ramp dip of ˜25° but permit a dip as great as 45°. Fluid inclusion data suggest that structures related to the hinge at the base of the ramp formed at depths of 12-25 km. If the average dip of the Brenner shear zone to those depths was 20°, intermediate between the favored ramp dip and the dip of exposed foliation, then the horizontal component of slip could be as high as 33-63 km. The two discrete sets of structures with opposite shear senses, formed in the temporal sequence indicated by PT data, are consistent with subvertical simple shear models of rolling-hinge strain. This kinematic pattern is not predicted by the flexural-failure model for rolling hinges. However, the predominance of normal slip at the upper hinge, which extends rather than shortens the mylonitic foliation, fails to match the subvertical simple shear model, which predicts shortening of the foliation there. One possible solution is that superposition of regional extension upon hinge-related stresses modified the rolling-hinge kinematics. Such a modified subvertical shear model can account for the observed small foliation-parallel extensional strains if the foliation was bent <5°-10° passing through the upper hinge. If more bending than that occurred, the data suggest rolling-hinge kinematics in which deformation is achieved by uniform-sense simple shear across the shear zone as in the subvertical simple shear model but in which material lines parallel to the shear-zone foliation and the detachment fault undergo very small length changes, presumably indicating that footwall rocks retained significant resistance to shear and underwent minimal permanent strain. The mechanics that would generate such a rolling hinge are uncertain but may incorporate aspects of both subvertical simple shear and flexural failure. An important kinematic consequence of such a rolling hinge is that all of the net slip across a normal fault, not only its horizontal component, is converted into horizontal extension. This implies a significantly larger magnitude of crustal extension across dipping normal faults whose footwalls passed through a rolling hinge than for those that did not develop along with a hinge.

Ethnicity and Onset of Cardiovascular Disease: A CALIBER Study

ClinicalTrials.gov

2017-06-07

Abdominal Aortic Aneurysm; Coronary Heart Disease; Sudden Cardiac Death; Intracerebral Haemorrhage; Heart Failure; Ischemic Stroke; Myocardial Infarction; Stroke; Peripheral Arterial Disease; Stable Angina Pectoris; Subarachnoid Haemorrhage; Transient Ischemic Attack; Unstable Angina; Cardiac Arrest

Serum Uric Acid Levels and Onset of Cardiovascular Diseases: a CALIBER Study

ClinicalTrials.gov

2018-02-06

Stable Angina; Unstable Angina; Myocardial Infarction; Unheralded Coronary Heart Disease Death; Heart Failure; Cardiac Arrest; Transient Ischaemic Attack; Ischemic Stroke; Subarachnoid Hemorrhage; Intracerebral Hemorrhage; Peripheral Arterial Disease; Abdominal Aortic Aneurysm; Atrial Fibrillation

Bullet Impact Safety Study of PBX-9502

NASA Astrophysics Data System (ADS)

Ferranti, Louis

2013-06-01

A new small arms capability for performing bullet impact testing into energetic materials has recently been activated at Lawrence Livermore National Laboratory located in the High Explosives Applications Facility (HEAF). The initial capability includes 0.223, 0.30, and 0.50 testing calibers with the flexibility to add other barrels in the near future. An initial test series has been performed using the 0.50 caliber barrel shooting bullets into targets using the TATB based explosive PBX-9502 and shows an expected non-violent reaction. Future experiments to evaluate the safety of new explosive formulations to bullet impact are planned. A highlight of the new capability along with discussion of the initial experiments to date will be presented including future areas of research. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Characteristics and measurement of supersonic projectile shock waves by a 32-microphone ring array

NASA Astrophysics Data System (ADS)

Chang, Ho; Wu, Yan-Chyuan; Tsung, Tsing-Tshih

2011-08-01

This paper discusses about the characteristics of supersonic projectile shock wave in muzzle region during firing of high explosive anti-tank (HEAT) and high explosive (HE) projectiles. HEAT projectiles are fired horizontally at a muzzle velocity of Mach 3.5 from a medium caliber tank gun equipped with a newly designed multi-perforated muzzle brake, whereas HE projectiles are fired at elevation angles at a muzzle velocity of Mach 2 from a large caliber howitzer equipped with a newly designed double-baffle muzzle brake. In the near field, pressure signatures of the N-wave generated from projectiles are measured by 32-microphone ring array wrapped by cotton sheath. Records measured by the microphone array are used to demonstrate several key characteristics of the shock wave of supersonic projectile. All measurements made in this study can be a significant reference for developing guns, tanks, or the chassis of fighting vehicles.

Improved multiple-shot gun for use as a combustion stability rating device

NASA Technical Reports Server (NTRS)

Sokolowski, D. E.

1973-01-01

A program was conducted to develop and experimentally evaluate an improved version of a modified machine gun for use as a device for rating the relative combustion stability of various rocket combustors. Following the results of a previous study involving a caliber .30 machine gun, a caliber .50 machine gun was modified in order to extend the charge-size range of the device. Nitrocellulose charge sizes ranging from 1.004 to 9.720 grams were fired at rates up to four shots per second. Shock pressures up to 25,512 kN/sq m were measured near the end of a shortened gun barrel. A minimal resistance type of check valve permitted the gun to fire into pressurized regions; back pressures up to 3448 kN/sq m abs were tested. The final modified assembly was evaluated during combustion stability tests on rocket combustors burning a FLOX-methane propellant combination.

Characteristics and measurement of supersonic projectile shock waves by a 32-microphone ring array.

PubMed

Chang, Ho; Wu, Yan-Chyuan; Tsung, Tsing-Tshih

2011-08-01

This paper discusses about the characteristics of supersonic projectile shock wave in muzzle region during firing of high explosive anti-tank (HEAT) and high explosive (HE) projectiles. HEAT projectiles are fired horizontally at a muzzle velocity of Mach 3.5 from a medium caliber tank gun equipped with a newly designed multi-perforated muzzle brake, whereas HE projectiles are fired at elevation angles at a muzzle velocity of Mach 2 from a large caliber howitzer equipped with a newly designed double-baffle muzzle brake. In the near field, pressure signatures of the N-wave generated from projectiles are measured by 32-microphone ring array wrapped by cotton sheath. Records measured by the microphone array are used to demonstrate several key characteristics of the shock wave of supersonic projectile. All measurements made in this study can be a significant reference for developing guns, tanks, or the chassis of fighting vehicles.

How does esophagus look on barium esophagram in pediatric eosinophilic esophagitis?

PubMed

Al-Hussaini, Abdulrahman; AboZeid, Amany; Hai, Abdul

2016-08-01

The clinical, endoscopic, and histologic findings of eosinophilic esophagitis (EoE) are well characterized; however, there have been very limited data regarding the radiologic findings of pediatric EoE. We report on the radiologic findings of pediatric EoE observed on barium esophagram and correlate them with the endoscopic findings. We identified children diagnosed with EoE in our center from 2004 to 2015. Two pediatric radiologists met after their independent evaluations of each fluoroscopic study to reach a consensus on each case. Clinical and endoscopic data were collected by retrospective chart review. Twenty-six pediatric EoE cases (age range 2-13 years; median 7.5 years) had barium esophagram done as part of the diagnostic approach for dysphagia. Thirteen children had abnormal radiologic findings of esophagus (50%): rings formation (n = 4), diffuse irregularity of mucosa (n = 8), fixed stricture formation (n = 3), and narrow-caliber esophagus (n = 10). Barium esophagram failed to show one of 10 cases of narrow-caliber esophagus and 10 of 14 cases of rings formation visualized endoscopically. The mean duration of symptoms prior to diagnosis of EoE was longer (3.7 vs. 1.7 year; p value 0.019), and the presentation with intermittent food impaction was commoner in the group with abnormal barium esophagram as compared to the group with normal barium esophagram (69% vs. 8%; p value 0.04). Barium swallow study is frequently normal in pediatric EoE. With the exception of narrow-caliber esophagus, our data show poor correlation between radiologic and endoscopic findings.

Advances in Global Water Cycle Science Made Possible by Global Precipitation Mission (GPM)

NASA Technical Reports Server (NTRS)

Smith, Eric A.; Starr, David OC. (Technical Monitor)

2001-01-01

Within this decade the internationally sponsored Global Precipitation Mission (GPM) will take an important step in creating a global precipitation observing system from space. One perspective for understanding the nature of GPM is that it will be a hierarchical system of datastreams from very high caliber combined dual frequency radar/passive microwave (PMW) rain-radiometer retrievals, to high caliber PMW rain-radiometer only retrievals, and on to blends of the former datastreams with other less-high caliber PMW-based and IR-based rain retrievals. Within the context of NASA's role in global water cycle science and its own Global Water & Energy Cycle (GWEC) program, GPM is the centerpiece mission for improving our understanding of the global water cycle from a space-based measurement perspective. One of the salient problems within our current understanding of the global water and energy cycle is determining whether a change in the rate of the water cycle is accompanying changes in global temperature. As there are a number of ways in which to define a rate-change of the global water cycle, it is not entirely clear as to what constitutes such a determination, This paper presents an overview of the Global Precipitation Mission and how its datasets can be used in a set of quantitative tests within the framework of the oceanic and continental water budget equations to determine comprehensively whether substantive rate changes do accompany perturbations in global temperatures and how such rate changes manifest themselves in both water storage and water flux transport processes.

Partial nephrectomy using radiofrequency incremental bipolar generator with multi electrode probe: experimental study in bench pig kidneys

PubMed Central

2014-01-01

Background The aim of this research project was the realization of an incremental bipolar radiofrequency generator with inline 4-electrode probe for partial renal resection without clamping of the vessels. Methods The experimentation was carried out across two phases: the preliminary realization of a specific generator and an inline multielectrode probe for open surgery (Phase 1); system testing on 27 bench kidneys for a total of 47 partial resection (Phase 2). The parameters evaluated were: power level, generator automatisms, parenchymal coagulation times, needle caliber, thickness of the coagulated tissue “slice”, charring, ergonomy, feasibility of the application of “bolster” stitches. Results The analysis of the results referred to the homogeneity and thickness of coagulation, energy supply times with reference to the power level and caliber of the needles. The optimal results were obtained by using needles of 1.5 mm caliber at power level 5, and with coagulation times of 54 seconds for the first insertion and 30 seconds for the second. Conclusions The experimentation demonstrated that the apparatus, consisting of a generator named “LaparoNewPro” and fitted with a dedicated probe for open surgery, is able to carry out a coagulation of the line of resection of the renal parenchyma in a homogeneous manner, in short times, without tissue charring, and with the possibility of stitching both on coagulated tissue and the caliceal system. The generator automatism based on the flow of the current supplied by each electrode is reliable, and the cessation of energy supply coincides with optimal coagulation. PMID:24410789

Microstructural control of FeCrAl alloys using Mo and Nb additions

DOE PAGES

Sun, Zhiqian; Bei, Hongbin; Yamamoto, Yukinori

2017-08-14

The effects of Mo and Nb additions on the microstructure and mechanical properties of two FeCrAl alloys were studied in this paper. Fine and uniform recrystallized grain structures (~ 20–30 μm) were achieved in both alloys through suitable annealing after warm-rolling. The formation of Fe 2Nb-type Laves phase precipitates in the Nb-containing FeCrAl alloy effectively stabilized the deformed and recrystallized microstructures. The Mo-containing FeCrAl alloy exhibited strong γ texture fiber after annealing at 650–900 °C, whereas the annealed Nb-containing FeCrAl alloy had much weaker texture. Finally, both strength and ductility decreased as the grain size increased in both alloys.

Heart Rate and Initial Presentation of Cardiovascular Diseases (Caliber)

ClinicalTrials.gov

2013-09-17

Abdominal Aortic Aneurysm; Coronary Heart Disease NOS; Unheralded Coronary Death; Intracerebral Haemorrhage; Heart Failure; Ischemic Stroke; Myocardial Infarction; Stroke; Peripheral Arterial Disease; Stable Angina Pectoris; Subarachnoid Haemorrhage; Transient Ischemic Attack; Unstable Angina; Cardiac Arrest, Sudden Cardiac Death

Effect of continuous annealing temperature on microstructure and properties of ferritic rolled interstitial-free steel

NASA Astrophysics Data System (ADS)

Qiu, Chen-yang; Li, Lang; Hao, Lei-lei; Wang, Jian-gong; Zhou, Xun; Kang, Yong-lin

2018-05-01

In this report, the microstructure, mechanical properties, and textures of warm rolled interstitial-free steel annealed at four different temperatures (730, 760, 790, and 820°C) were studied. The overall structural features of specimens were investigated by optical microscopy, and the textures were measured by X-ray diffraction (XRD). Nano-sized precipitates were then observed by a transmission electron microscope (TEM) on carbon extraction replicas. According to the results, with increased annealing temperatures, the ferrite grains grew; in addition, the sizes of Ti4C2S2 and TiC precipitates also increased. Additionally, the sizes of TiN and TiS precipitates slightly changed. When the annealing temperature increased from 730 to 820°C, the yield strength (YS) and the ultimate tensile strength (UTS) showed a decreasing trend. Meanwhile, elongation and the strain harden exponent (n value) increased to 49.6% and 0.34, respectively. By comparing textures annealed at different temperatures, the intensity of {111} texture annealed at 820°C was the largest, while the difference between the intensity of {111}<110> and {111}<112> was the smallest when the annealing temperature was 820°C. Therefore, the plastic strain ratio (r value) annealed at 820°C was the highest.

Effect of cyclic treatment on the formation of a fragmented structure in a sparingly alloyed martensitic steel

NASA Astrophysics Data System (ADS)

Tabatchikova, T. I.; Yakovleva, I. L.; Delgado Reina, S. Yu.; Plokhikh, A. I.

2016-11-01

Methods of metallography and transmission electron microscopy were used to study the structure of a high-alloy low-carbon steel of martensitic VKS-10 class subjected to cyclic treatment according to different regimes. It has been found that the warm deformation in the α state at 700°C causes the fragmentation of the structure; however, the decomposition of the α solid solution and the precipitation of coarse carbides leads to a significant decrease in the strength. It has been shown that 12 cycles of treatment, including austenitizing at 1000°C, rolling at 700°C, and subsequent γ → α transformation during rapid cooling do not lead to a noticeable fragmentation of the structure. It has been found that the deformation of the overcooled austenite by rolling carried out using 12 cycles in the range of temperatures of 700-500°C and subsequent γ → α transformation lead to the formation of a fragmented structure with a large fraction of fine grains with a size less than 0.5 μm. This treatment and the subsequent tempering at 530°C for 1 h allow us to increase the strength and hardness of the VKS-10 steel at an insignificant decrease in the plasticity.

Social Deprivation and Initial Presentation of 12 Cardiovascular Diseases: a CALIBER Study

ClinicalTrials.gov

2013-09-03

Abdominal Aortic Aneurysm; Coronary Heart Disease NOS; Unheralded Corronary Death; Intracerebral Haemorrhage; Heart Failure; Ischemic Stroke; Myocardial Infarction; Stroke; Peripheral Arterial Disease; Stable Angina Pectoris; Subarachnoid Haemorrhage; Transient Ischemic Attack; Unstable Angina; Cardiac Arrest, Sudden Cardiac Death

CUSTOMER/SUPPLIER ACCOUNTABILITY AND PROGRAM IMPLEMENTATION

EPA Science Inventory

Quality assurance (QA) and quality control (QC) are the basic components of a QA program, which is a fundamental quality management tool. he quality of outputs and services strongly depends on the caliber of the communications between the "customer" and the "supplier." lear under...

Visual search and urban city driving under the influence of marijuana and alcohol

DOT National Transportation Integrated Search

2000-03-01

The purpose of this study was to empirically determine the separate and combined effects of delta-9-tetrahydrocannabinol (THC) and alcohol on visual search and actual city driving performance. On separate evenings, 16 subjects were given weight-calib...

Fourier transform spectroscopy of cotton and cotton trash

USDA-ARS?s Scientific Manuscript database

Fourier Transform techniques have been shown to have higher signal-to-noise capabilities, higher throughput, negligible stray light, continuous spectra, and higher resolution. In addition, FT spectroscopy affords for frequencies in spectra to be measured all at once and more precise wavelength calib...

Analysis of Rail Gun Bore Residue

DTIC Science & Technology

1984-03-01

erosion effects and elemental analysis of refractory materials. C. A. L. Westerdahl , J. Pinto, G. L. Ferventino, D. N. Saherhavth...accelerator facility at Large Caliber Weapons Systems Laboratory Dover, New Jersey. ’ 16 REFERENCES 1. C.A.L. Westerdahl , J. Pinto, G. L. Ferrentino, D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gregorio, Miguel A. de; Ruiz, Carlos; Alfonso, Eduardo R.

Purpose: To assess the efficacy of intrapleural urokinase instillation through small-caliber catheters for the treatment of loculate and/or septate effusions. Methods: We inserted small-caliber catheters (8.2 Fr) in 102 patients with septate and/or loculate pleural effusions using ultrasonographic guidance. Urokinase (100,000 IU/2 hr, 3 times a day) was instilled through the catheter until the effusion resolved and D-dimer levels were <500 ng/ml. Patients were enrolled regardless of the etiology of the pleural effusion provided there were no contraindications for the use of urokinase. D-dimer levels were determined before and after treatment. Follow-up was performed by chest radiograph and sonography atmore » 1 day, 7 days, and every 30 days thereafter for 6 months. Results: Successful catheter placement was achieved in all cases. The mean time catheters stayed in place was 5.7 days and the mean dose of drug instilled was 690,000 IU. Pleural effusion drainage was complete at the first assessment in all patients. Failure of the treatment, with recurrent effusion at 30 days, occurred in six patients (5.8%). Complete resolution without sequelae was observed in 19 patients (19.6%). In 75 cases (73.5%) resolution was partial, with pleural thickening (>2 mm). Two patients died from unrelated causes within 30 days after catheter placement. Complications were seen in 13 patients (12.74%): hydropneumothorax, nine cases (8.82%); infection of the puncture point, three cases (2.94%); and adverse reaction, one case (0.98%). No further treatment was required. Conclusion: The use of intrapleural fibrinolytic agents delivered through small-caliber catheters for the treatment of loculate and/or septate pleural effusion is a simple, effective, minimally invasive and inexpensive procedure that can prevent sequelae and shorten drainage time.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Gregorio, Miguel A.; Ruiz, Carlos; Alfonso, Eduardo R.

Purpose: To assess the efficacy of intrapleural urokinase instillation through smll-caliber catheters for the treatment of loculate and/or septate effusions.Methods: We inserted small-caliber catheters (8.2 Fr) in 102 patients with septate and/or loculate pleural effusions using ultrasonographic guidance. Urokinase (100,000 IU/2 hr, 3 times a day) was instilled through the catheter until the effusion resolved and D-dimer levels were <500 ng/ml. Patients were enrolled regardless of the etiology of the pleural effusion provided there were no contraindications for the use of urokinase. D-dimer levels were determined before and after treatment. Follow-up was performed by chest radiograph and sonography at 1more » day, 7 days, and every 30 days thereafter for 6 months.Results: Successful catheter placement was achieved in all cases. The mean time catheters stayed in place was 5.7 days and the mean dose of drug instilled was 690,000 IU. Pleural effusion drainage was complete at the first assessment in all patients. Failure of the treatment, with recurrent effusion at 30 days, occurred in six patients (5.8%). Complete resolution without sequelae was observed in 19 patients (19.6%). In 75 cases (73.5%) resolution was partial, with pleural thickening (>2 mm). Two patients died from unrelated causes within 30 days after catheter placement. Complications were seen in 13 patients (12.74%): hydropneumothorax, nine cases (8.82%); infection of the puncture point, three cases (2.94%); and adverse reaction, one case (0.98%). No further treatment was required.Conclusions: The use of intrapleural fibrinolytic agents delivered through small-caliber catheters for the treatment of loculate and/or septate pleural effusion is a simple, effective, minimally invasive and inexpensive procedure that can prevent sequelae and shorten drainage time.« less

Serum Phosphate and Retinal Microvascular Changes: The Multi-Ethnic Study of Atherosclerosis and the Beaver Dam Eye Study.

PubMed

Mehta, Rupal; Hodakowski, Alexander; Cai, Xuan; Lee, Kris E; Kestenbaum, Bryan R; de Boer, Ian H; Fawzi, Amani; Wong, Tien Yin; Ix, Joachim; Klein, Barbara; Klein, Ronald; Isakova, Tamara

2017-12-01

Higher levels of serum phosphate are strongly linked to increased risk of cardiovascular disease and therapies aimed to lower serum phosphate are employed in the management of patients with chronic kidney disease (CKD). Data are limited, however, on serum phosphate as a risk factor for microvascular disease in community-based populations. It is important to determine the impact of novel risk factors, such as phosphate, on the microvasculature. We conducted a prospective study of 3919 individuals in the Multi-Ethnic Study of Atherosclerosis (MESA) and 3544 individuals in the Beaver Dam Eye Study (BDES) to test the associations of serum phosphate with retinopathy and retinal vessel caliber, and change in retinopathy severity and change in retinal vessel caliber. Mean (standard deviation) serum phosphate was 3.66 (0.52) mg/dl in the MESA and 3.77 (0.55) mg/dl in the BDES. In multivariable adjusted models, phosphate was significantly associated with prevalent retinopathy in the MESA (Odds Ratio [OR] per 1 mg/dl increase in phosphate, 1.22; Confidence Interval [CI] 1.02-1.47) and the BDES (OR 1.06; CI 1.01-1.11). In stratified analyses, these relationships were even stronger and only seen in individuals with diabetes in both the MESA (OR 1.81; CI 1.30-2.53) and the BDES (OR 1.16; CI 1.05-1.29). Phosphate was not associated with incident or change in retinopathy severity, nor any retinal caliber outcome. Among community-living individuals with low prevalence of CKD, higher serum phosphate was associated with prevalent retinopathy in individuals with diabetes. Further longitudinal assessments in patients with diabetes necessitate further investigation.

Retinal vascular caliber and the development of hypertension: a meta-analysis of individual participant data.

PubMed

Ding, Jie; Wai, Khin Lay; McGeechan, Kevin; Ikram, M Kamran; Kawasaki, Ryo; Xie, Jing; Klein, Ronald; Klein, Barbara B K; Cotch, Mary Frances; Wang, Jie Jin; Mitchell, Paul; Shaw, Jonathan E; Takamasa, Kayama; Sharrett, A Richey; Wong, Tien Y

2014-02-01

Microvascular dysfunction has been suggested to be a major pathogenic factor for the development of hypertension. We examined the association between retinal vascular caliber, a marker of systemic microvascular dysfunction, and incident hypertension on a meta-analysis of individual participant data. We performed a systematic review with relevant studies identified through a search of electronic databases, a review of reference lists, and correspondence with experts. Studies were included if participants were selected from a general population, retinal vascular caliber was measured from photographs using computer-assisted methods at baseline, and individuals were followed up to ascertain the incidence of hypertension. Prespecified individual recorded data from six population-based prospective cohort studies were included. Discrete time proportional odds models were constructed for each study with adjustment for hypertension risk factors. Log odds ratios (ORs) per 20-μm difference were pooled using random-effects meta-analysis. Among 10 229 participants without prevalent hypertension, diabetes, or cardiovascular disease, 2599 developed new-onset hypertension during median follow-up periods ranging from 2.9 to 10 years. Both narrower retinal arterioles [pooled multivariate-adjusted OR per 20-μm difference 1.29, 95% confidence interval (CI) 1.20-1.39] and wider venules (OR per 20-μm difference 1.14, 95% CI 1.06-1.23) were associated with an increased risk of hypertension. Each 20 μm narrower arterioles at baseline were associated with a 1.12 mmHg (95% CI 0.25-1.99) greater increase in SBP over 5 years. Retinal arteriolar narrowing and venular widening were independently associated with an increased risk of hypertension. These findings underscore the importance of microvascular remodeling in the pathogenesis of hypertension.

Clinical anatomy of the orbitomeningeal foramina: variational anatomy of the canals connecting the orbit with the cranial cavity.

PubMed

Macchi, Veronica; Regoli, Marì; Bracco, Sandra; Nicoletti, Claudio; Morra, Aldo; Porzionato, Andrea; De Caro, Raffaele; Bertelli, Eugenio

2016-03-01

In addition to the optic canal and the superior orbital fissure, orbits are connected with the cranial cavity via inconstant canals including the orbitomeningeal foramen. This study has been carried out in order to define many anatomical and radiological details of the orbitomeningeal foramen that are relevant in the clinical practice. Almost 1000 skulls and 50 computerized tomographies were examined to determine incidence, number, length, and caliber of the orbitomeningeal foramen as well as the topography of their orbital and cranial openings. A retrospective study of angiographies carried out on more than 100 children was performed to look for arteries candidate to run through the orbitomeningeal foramen. Orbitomeningeal foramina were detected in 59.46% of skulls and in 54% of individuals by computerized tomography. Orbits with two to five foramina were found. Canals were classified as M-subtype or A-subtype depending on their cranial opening. Large foramina, with the caliber ranging between 1 and 3 mm, were found in 12.17% of orbitomeningeal foramen-bearing orbits. By computed tomography the average caliber measured 1.2 ± 0.3 and 1.5 ± 0.5 mm (p < 0.005) at the orbital and cranial openings, respectively (p < 0.005). Angiographies showed meningo-lacrimal and meningo-ophthalmic arteries, meningeal branches of the lacrimal and supraorbital arteries, and some unidentified arteries that could pass through the orbitomeningeal foramina. Orbitomeningeal foramina are a common occurrence. When large they may house important arteries that can be the source of severe bleedings during deep dissection of the lateral wall of the orbit. Orbital surgeons should be aware of their existence.

Reproducibility of Retinal Microvascular Traits Decoded by the Singapore I Vessel Assessment Software Across the Human Age Range.

PubMed

Huang, Qi-Fang; Wei, Fang-Fei; Zhang, Zhen-Yu; Raaijmakers, Anke; Asayama, Kei; Thijs, Lutgarde; Yang, Wen-Yi; Mujaj, Blerim; Allegaert, Karel; Verhamme, Peter; Struijker-Boudier, Harry A J; Li, Yan; Staessen, Jan A

2018-03-10

Retinal microvascular traits predict adverse health outcomes. The Singapore I Vessel Assessment (SIVA) software improved automated postprocessing of retinal photographs. In addition to microvessel caliber, it generates measures of arteriolar and venular geometry. Few studies addressed the reproducibility of SIVA measurements across a wide age range. In the current study, 2 blinded graders read images obtained by nonmydriatic retinal photography twice in 20 11-year-old children, born prematurely (n = 10) or at term (n = 10) and in 60 adults (age range, 18.9-86.1 years). Former preterm compared with term children had lower microvessel diameter and disorganized vessel geometry with no differences in intraobserver and interobserver variability. Among adults, microvessel caliber decreased with age and blood pressure and arteriolar geometry was inversely correlated with female sex and age. Intraobserver differences estimated by the Bland-Altman method did not reach significance for any measurement. Across measurements, median reproducibility (RM) expressed as percent of the average trait value was 8.8% in children (median intraclass correlation coefficient [ICC], 0.94) and 8.0% (0.97) in adults. Likewise, interobserver differences did not reach significance with RM (ICC) of 10.6% (0.85) in children and 10.4% (0.93) in adults. Reproducibility was best for microvessel caliber (intraobserver/interobserver RM, 4.7%/6.0%; ICC, 0.98/0.96), worst for venular geometry (17.0%/18.8%; 0.93/0.84), and intermediate for arteriolar geometry (10.9%/14.9%; 0.95/0.86). SIVA produces repeatable measures of the retinal microvasculature in former preterm and term children and in adults, thereby proving its usability from childhood to old age.

No effect of elevated operating lung volumes on airway function during variable workrate exercise in asthmatic humans.

PubMed

Klansky, Andrew; Irvin, Charlie; Morrison-Taylor, Adriane; Ahlstrand, Sarah; Labrie, Danielle; Haverkamp, Hans Christian

2016-07-01

In asthmatic adults, airway caliber fluctuates during variable intensity exercise such that bronchodilation (BD) occurs with increased workrate whereas bronchoconstriction (BC) occurs with decreased workrate. We hypothesized that increased lung mechanical stretch would prevent BC during such variable workrate exercise. Ten asthmatic and ten nonasthmatic subjects completed two exercise trials on a cycle ergometer. Both trials included a 28-min exercise bout consisting of alternating four min periods at workloads equal to 40 % (Low) and 70% (High) peak power output. During one trial, subjects breathed spontaneously throughout exercise (SVT), such that tidal volume (VT) and end-inspiratory lung volume (EILV) were increased by 0.5 and 0.6 liters during the high compared with the low workload in nonasthmatic and asthmatic subjects, respectively. During the second trial (MVT), VT and EILV were maintained constant when transitioning from the high to the low workload. Forced exhalations from total lung capacity were performed during each exercise workload. In asthmatic subjects, forced expiratory volume 1.0 s (FEV1.0) increased and decreased with the increases and decreases in workrate during both SVT (Low, 3.3 ± 0.3 liters; High, 3.6 ± 0.2 liters; P < 0.05) and MVT (Low, 3.3 ± 0.3 liters; High, 3.5 ± 0.2 liters; P < 0.05). Thus increased lung stretch during MVT did not prevent decreases in airway caliber when workload was reduced. We conclude that neural factors controlling airway smooth muscle (ASM) contractile activity during whole body exercise are more robust determinants of airway caliber than the ability of lung stretch to alter ASM actin-myosin binding and contraction. Copyright © 2016 the American Physiological Society.

Retinal vascular caliber, iris color, and age-related macular degeneration in the Irish Nun Eye Study.

PubMed

McGowan, Amy; Silvestri, Giuliana; Moore, Evelyn; Silvestri, Vittorio; Patterson, Christopher C; Maxwell, Alexander P; McKay, Gareth J

2014-12-18

To evaluate the relationship between retinal vascular caliber (RVC), iris color, and age-related macular degeneration (AMD) in elderly Irish nuns. Data from 1233 participants in the cross-sectional observational Irish Nun Eye Study were assessed from digital photographs with a standardized protocol using computer-assisted software. Macular images were graded according to the modified Wisconsin Age-related Maculopathy Grading System. Regression models were used to assess associations, adjusting for age, mean arterial blood pressure, body mass index, refraction, and fellow RVC. In total, 1122 (91%) participants had gradable retinal images of sufficient quality for vessel assessment (mean age: 76.3 years [range, 56-100 years]). In an unadjusted analysis, we found some support for a previous finding that individuals with blue iris color had narrower retinal venules compared to those with brown iris color (P < 0.05), but this was no longer significant after adjustment. Age-related macular degeneration status was categorized as no AMD, any AMD, and late AMD only. Individuals with any AMD (early or late AMD) had significantly narrower arterioles and venules compared to those with no AMD in an unadjusted analysis, but this was no longer significant after adjustment. A nonsignificant reduced risk of any AMD or late AMD only was observed in association with brown compared to blue iris color, in both unadjusted and adjusted analyses. Retinal vascular caliber was not significantly associated with iris color or early/late AMD after adjustment for confounders. A lower but nonsignificant AMD risk was observed in those with brown compared to blue iris color. Copyright 2015 The Association for Research in Vision and Ophthalmology, Inc.

Retinal vessel caliber among people with acquired immunodeficiency syndrome: relationships with disease-associated factors and mortality.

PubMed

Gangaputra, Sapna; Kalyani, Partho S; Fawzi, Amani A; Van Natta, Mark L; Hubbard, Larry D; Danis, Ronald P; Thorne, Jennifer E; Holland, Gary N

2012-03-01

To evaluate relationships between retinal vessel caliber, AIDS-related factors, and mortality. Longitudinal, observational cohort study. We evaluated data for participants without ocular opportunistic infections at initial examination (baseline) in the Longitudinal Studies of the Ocular Complications of AIDS (1998-2008). Semi-automated evaluation of fundus photographs (1 eye/participant) determined central retinal artery equivalent (CRAE), central retinal vein equivalent (CRVE), and arteriole-to-venule ratio (AVR) at baseline. Multiple linear regression models, using forward selection, identified independent relationships between indices and various host- and disease-related variables. Included were 1250 participants. Mean follow-up for determination of mortality was 6.1 years. Smaller CRAE was related to increased age (P < .001) and hypertension (P < .001); larger CRAE was related to lower hematocrit (P = .002). Larger CRAE and CRVE were associated with black race (P < .001). Larger CRVE was related to smoking (P = .004); smaller CRVE was related to age (P < .001) and higher mean corpuscular volume (P = .001). We observed the following relationships with AIDS-associated factors: smaller CRAE and larger CRVE with history of highly active antiretroviral therapy (HAART; P < .001); and larger CRAE with lower CD4+ T lymphocyte count (P = .04). We did not identify independent relationships with human immunodeficiency virus RNA blood levels. There was a 12% (95% CI, 2%-21%) increase in mortality risk per quartile of decreasing AVR (P = .02). Variations in retinal vascular caliber are associated with AIDS-specific factors and are markers for increased mortality risk. Relationships are consistent with the hypothesis that the vasculature is altered by known atherogenic effects of chronic HAART or the prolonged inflammatory state associated with AIDS. Copyright © 2012 Elsevier Inc. All rights reserved.

Biomimetic coating of cross-linked gelatin to improve mechanical and biological properties of electrospun PET: A promising approach for small caliber vascular graft applications.

PubMed

Pezzoli, Daniele; Cauli, Elisa; Chevallier, Pascale; Farè, Silvia; Mantovani, Diego

2017-09-01

Electrospun PET (ePET) is a promising material for small caliber vascular graft applications owing to its tunable mechanical properties, biocompatibility, and nanofibrous structure that mimic the morphology of natural extracellular matrix. However, the inherent inertness of PET impairs the adhesion and proliferation of endothelial cells on the inner surface of ePET tubular grafts, hindering the formation of a functional endothelium. Gelatin coatings, owing to their ability to promote endothelialization, are a valuable approach to overcome the limitations of ePET. Herein, a novel process for the deposition of stable biomimetic coatings of gelatin on ePET tubular grafts is proposed. Electrospun PET was first aminated by plasma treatment and then coated with a gelatin hydrogel cross-linked in situ by a Michael-type addition reaction. Amination provided a superhydrophilic behavior to the ePET surface, allowing easy gelatin interpenetration along the wall thickness of the tubular structure, and the obtainment of thin coatings that maintained the morphology of ePET fibers. Gelatin coating was stable at long term in a physiological-like environment, noncytotoxic and promoted in vitro cell adhesion and proliferation. Noteworthy, the mechanical properties of gelatin-coated ePET tubular grafts were improved in terms of elastic modulus, compliance, and elastic recoil, finally better matching the characteristics of native blood vessels. Altogether, the proposed coating technique successfully combines the advantages of ePET nanofibrous structure with cross-linked gelatin biological cues and mechanical reinforcement, and emerges as a promising strategy for the development of biocompatible small caliber vascular grafts with superior biomimetic and mechanical properties. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 2405-2415, 2017. © 2017 Wiley Periodicals, Inc.

Optical Coherence Tomography Angiography Features of Iris Racemose Hemangioma in 4 Cases.

PubMed

Chien, Jason L; Sioufi, Kareem; Ferenczy, Sandor; Say, Emil Anthony T; Shields, Carol L

2017-10-01

Optical coherence tomography angiography (OCTA) allows visualization of iris racemose hemangioma course and its relation to the normal iris microvasculature. To describe OCTA features of iris racemose hemangioma. Descriptive, noncomparative case series at a tertiary referral center (Ocular Oncology Service of Wills Eye Hospital). Patients diagnosed with unilateral iris racemose hemangioma were included in the study. Features of iris racemose hemangioma on OCTA. Four eyes of 4 patients with unilateral iris racemose hemangioma were included in the study. Mean patient age was 50 years, all patients were white, and Snellen visual acuity was 20/20 in each case. All eyes had sectoral iris racemose hemangioma without associated iris or ciliary body solid tumor on clinical examination and ultrasound biomicroscopy. By anterior segment OCT, the racemose hemangioma was partially visualized in all cases. By OCTA, the hemangioma was clearly visualized as a uniform large-caliber vascular tortuous loop with intense flow characteristics superimposed over small-caliber radial iris vessels against a background of low-signal iris stroma. The vascular course on OCTA resembled a light bulb filament (filament sign), arising from the peripheral iris (base of light bulb) and forming a tortuous loop on reaching its peak (midfilament) near the pupil (n = 3) or midzonal iris (n = 1), before returning to the peripheral iris (base of light bulb). Intravenous fluorescein angiography performed in 1 eye depicted the iris hemangioma; however, small-caliber radial iris vessels were more distinct on OCTA than intravenous fluorescein angiography. Optical coherence tomography angiography is a noninvasive vascular imaging modality that clearly depicts the looping course of iris racemose hemangioma. Optical coherence tomography angiography depicted fine details of radial iris vessels, not distinct on intravenous fluorescein angiography.

Decreased Axon Caliber Underlies Loss of Fiber Tract Integrity, Disproportional Reductions in White Matter Volume, and Microcephaly in Angelman Syndrome Model Mice

PubMed Central

Judson, Matthew C.; Burette, Alain C.; Shen, Mark D.; Rumple, Ashley M.; Del Cid, Wilmer A.; Paniagua, Beatriz

2017-01-01

Angelman syndrome (AS) is a debilitating neurodevelopmental disorder caused by loss of function of the maternally inherited UBE3A allele. It is currently unclear how the consequences of this genetic insult unfold to impair neurodevelopment. We reasoned that by elucidating the basis of microcephaly in AS, a highly penetrant syndromic feature with early postnatal onset, we would gain new insights into the mechanisms by which maternal UBE3A loss derails neurotypical brain growth and function. Detailed anatomical analysis of both male and female maternal Ube3a-null mice reveals that microcephaly in the AS mouse model is primarily driven by deficits in the growth of white matter tracts, which by adulthood are characterized by densely packed axons of disproportionately small caliber. Our results implicate impaired axon growth in the pathogenesis of AS and identify noninvasive structural neuroimaging as a potentially valuable tool for gauging therapeutic efficacy in the disorder. SIGNIFICANCE STATEMENT People who maternally inherit a deletion or nonfunctional copy of the UBE3A gene develop Angelman syndrome (AS), a severe neurodevelopmental disorder. To better understand how loss of maternal UBE3A function derails brain development, we analyzed brain structure in a maternal Ube3a knock-out mouse model of AS. We report that the volume of white matter (WM) is disproportionately reduced in AS mice, indicating that deficits in WM development are a major factor underlying impaired brain growth and microcephaly in the disorder. Notably, we find that axons within the WM pathways of AS model mice are abnormally small in caliber. This defect is associated with slowed nerve conduction, which could contribute to behavioral deficits in AS, including motor dysfunction. PMID:28663201

Adaptations in the structure and innervation of follicle-sinus complexes to an aquatic environment as seen in the Florida manatee (Trichechus manatus latirostris).

PubMed

Sarko, Diana K; Reep, Roger L; Mazurkiewicz, Joseph E; Rice, Frank L

2007-09-20

Florida manatees are large-bodied aquatic herbivores that use large tactile vibrissae for several purposes. Facial vibrissae are used to forage in a turbid water environment, and the largest perioral vibrissae can also grasp and manipulate objects. Other vibrissae distributed over the entire postfacial body appear to function as a lateral line system. All manatee vibrissae emanate from densely innervated follicle-sinus complexes (FSCs) like those in other mammals, although proportionately larger commensurate with the caliber of the vibrissae. As revealed by immunofluorescence, all manatee FSCs have many types of C, Adelta and Abeta innervation including Merkel, club, and longitudinal lanceolate endings at the level of the ring sinus, but they lack other types such as reticular and spiny endings at the level of the cavernous sinus. As in non-whisking terrestrial species, the inner conical bodies of facial FSCs are well innervated but lack Abeta-fiber terminals. Importantly, manatee FSCs have two unique types of Abeta-fiber endings. First, all of the FSCs have exceptionally large-caliber axons that branch to terminate as novel, gigantic spindle-like endings located at the upper ring sinus. Second, facial FSCs have smaller caliber Abeta fibers that terminate in the trabeculae of the cavernous sinus as an ending that resembles a Golgi tendon organ. In addition, the largest perioral vibrissae, which are used for grasping, have exceptionally well-developed medullary cores that have a structure and dense small-fiber innervation resembling that of tooth pulp. Other features of the epidermis and upper dermis structure and innervation differ from that seen in terrestrial mammals. Copyright (c) 2007 Wiley-Liss, Inc.

Power spectra in warm G inflation and its consistency: Stochastic approach

NASA Astrophysics Data System (ADS)

Motaharfar, Meysam; Massaeli, Erfan; Sepangi, Hamid Reza

2017-11-01

Recently, it has been realized that the so-called G -inflation model inspired by supplementing a generalized covariant Galileon-like nonlinear derivative self-interacting term to the standard kinetic term should be ruled out from inflationary models. This is due to the fact that it suffers from lack of an oscillatory phase at the end of the inflationary regime which is typically accompanied by the appearance of a negative squared propagation speed of the scalar mode leading to instabilities of small-scale perturbations. In this regard, the warm G -inflation scenario is proposed where for G inflation to survive, the Galileon scalar field is coupled to the radiation field through a dissipation term which results in removing the reheating period due to the characteristics of warm inflationary scenario. In so doing, a linear stability analysis is first performed to obtain the appropriate slow-roll conditions in such a proposal. Cosmological perturbations of the model are then investigated by utilizing a fluctuation-dissipation theorem and analytical expressions are derived for observable quantities; the power spectrum, tilt spectral index, and tensor-to-scalar ratio in terms of P S R parameters and Galileon flow functions. Finally, the model is solved for chaotic self-interacting potentials, particularly the renormalizable Higgs potential λ/4 ϕ4, and shown to be consistent with observations in the weak dissipation Q ≪1 +3 δ/GXδX and G -dominant 3 δ/GXδX≫1 regime despite its large self-coupling, since the energy scale at the horizon crossing is depressed by the synergy of Galileon and thermal effects.

Prevalence and work-related risk factors for reduced activities and absenteeism due to low back symptoms.

PubMed

Widanarko, Baiduri; Legg, Stephen; Stevenson, Mark; Devereux, Jason; Eng, Amanda; 't Mannetje, Andrea; Cheng, Soo; Pearce, Neil

2012-07-01

Although quite a lot is known about the risk factors for low back symptoms (LBS), less is known about the risk factors for the consequences of LBS. A sample of 3003 men and women randomly selected from the New Zealand Electoral Roll, were interviewed by telephone about self reported physical, psychosocial, organizational, environmental factors and the consequences of LBS (i.e. self-reported reduced activities and absenteeism). The 12-month period prevalence of reduced activities and absenteeism were 18% and 9%, respectively. Lifting (OR 1.79 95% CI 1.16-2.77) increased the risk of reduced activities. Working in awkward/tiring positions (OR 2.11 95% CI 1.20-3.70) and in a cold/damp environment (OR 2.18 95% CI 1.11-4.28) increased the risk of absenteeism. Among those with LBS, reduced activities increased with working in a hot/warm environment (OR 2.14 95% CI 1.22-3.76) and absenteeism was increased with work in awkward/tiring positions (OR 2.06 95% CI 1.13-3.77), tight deadlines (OR 1.89 95% CI 1.02-3.50), and a hot/warm environment (OR 3.35 95% CI 1.68-6.68). Interventions to reduce the consequences of LBS should aim to reduce awkward/tiring positions, lifting and work in a cold/damp environment. For individuals with LBS, additional focus should be to reduce tight deadlines, and work in hot/warm environments. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Intelligent transportation systems for traffic incident management : deployment benefits and lessons learned.

DOT National Transportation Integrated Search

2001-01-01

This report discusses why the Long Term Pavement Performance (LTPP) program is still important today; what the current investment in LTPP is; what the value of this investment is; the benefits of LTPP to date; falling weight deflectometer (FWD) calib...

Unusual blunt force wound produced by a gun muzzle.

PubMed

Hanzlick, R; Zaki, S A

1986-09-01

Most blunt force injuries produced by guns are associated with gun butts, and patterned, muzzle/sight impressions are usually produced by discharging firearms. An unusual and distinct forehead laceration produced by a blow with the muzzle end of a .32 caliber revolver is presented.

Attenuated total reflectance-FT-IR spectroscopy for gunshot residue analysis: potential for ammunition determination.

PubMed

Bueno, Justin; Sikirzhytski, Vitali; Lednev, Igor K

2013-08-06

The ability to link a suspect to a particular shooting incident is a principal task for many forensic investigators. Here, we attempt to achieve this goal by analysis of gunshot residue (GSR) through the use of attenuated total reflectance (ATR) Fourier transform infrared spectroscopy (FT-IR) combined with statistical analysis. The firearm discharge process is analogous to a complex chemical process. Therefore, the products of this process (GSR) will vary based upon numerous factors, including the specific combination of the firearm and ammunition which was discharged. Differentiation of FT-IR data, collected from GSR particles originating from three different firearm-ammunition combinations (0.38 in., 0.40 in., and 9 mm calibers), was achieved using projection to latent structures discriminant analysis (PLS-DA). The technique was cross (leave-one-out), both internally and externally, validated. External validation was achieved via assignment (caliber identification) of unknown FT-IR spectra from unknown GSR particles. The results demonstrate great potential for ATR-FT-IR spectroscopic analysis of GSR for forensic purposes.

Perspective: Maximum caliber is a general variational principle for dynamical systems

NASA Astrophysics Data System (ADS)

Dixit, Purushottam D.; Wagoner, Jason; Weistuch, Corey; Pressé, Steve; Ghosh, Kingshuk; Dill, Ken A.

2018-01-01

We review here Maximum Caliber (Max Cal), a general variational principle for inferring distributions of paths in dynamical processes and networks. Max Cal is to dynamical trajectories what the principle of maximum entropy is to equilibrium states or stationary populations. In Max Cal, you maximize a path entropy over all possible pathways, subject to dynamical constraints, in order to predict relative path weights. Many well-known relationships of non-equilibrium statistical physics—such as the Green-Kubo fluctuation-dissipation relations, Onsager's reciprocal relations, and Prigogine's minimum entropy production—are limited to near-equilibrium processes. Max Cal is more general. While it can readily derive these results under those limits, Max Cal is also applicable far from equilibrium. We give examples of Max Cal as a method of inference about trajectory distributions from limited data, finding reaction coordinates in bio-molecular simulations, and modeling the complex dynamics of non-thermal systems such as gene regulatory networks or the collective firing of neurons. We also survey its basis in principle and some limitations.

Quantum dot interactions and flow effects in angiogenic zebrafish (Danio rerio) vessels and human endothelial cells.

PubMed

Jiang, Xiao-Yu; Sarsons, Christopher D; Gomez-Garcia, M Juliana; Cramb, David T; Rinker, Kristina D; Childs, Sarah J

2017-04-01

Nanoparticle (NP) interactions with biological tissues are affected by the size, shape and surface chemistry of the NPs. Here we use in vivo (zebrafish) and in vitro (HUVEC) models to investigate association of quantum dots (QDs) with endothelial cells and the effect of fluid flow. After injection into the developing zebrafish, circulating QDs associate with endothelium and penetrate surrounding tissue parenchyma over time. Amino-functionalized QDs cluster, interact with cells, and clear more rapidly than carboxy-functionalized QDs in vivo, highlighting charge influences. QDs show stronger accumulation in slow-flowing, small caliber venous vessels than in fast-flowing high caliber arterial vessels. Parallel-plate flow experiments with HUVEC support these findings, showing reduced QD-EC association with increasing flow. In vivo, flow arrest after nanoparticle injection still results in venous accumulation at 18 h. Overall our results suggest that both QD charge and blood flow modulate particle-endothelial cell interactions. Copyright © 2016 Elsevier Inc. All rights reserved.

Identification of gunshot residues in fabric targets using sector field inductively coupled plasma mass spectrometry technique and ternary graphs.

PubMed

Freitas, João Carlos D; Sarkis, Jorge E Souza; Negrini Neto, Osvaldo; Viebig, Sônia Bocamino

2012-03-01

During criminal investigations involving firearms, the detection of gunshot residues (GSRs) is one of the most important evidences. In the present study, a new method to identify trace evidences of GSRs, deposited around the bullet entrance hole, in different types of fabrics used as targets, is described. The experiments were carried out using a 0.38-inch caliber revolver, and 9-mm and 0.40-inch caliber pistols. Testimonies of 2.25 cm(2) of the fabrics were cut around the bullet entrance and digested with 10% nitric acid. Antimony, barium, and lead were analyzed in the remaining solution using a sector field inductively coupled plasma mass spectrometer. The concentrations of the elements were detected at levels up to few microgram per square centimeter. The use of ternary graphics allowed us to identify specific patterns of distribution for blank samples and the clear distinction between the revolver and pistols used. © 2011 American Academy of Forensic Sciences.

Forecasting the impact of an 1859-caliber superstorm on geosynchronous Earth-orbiting satellites: Transponder resources

NASA Astrophysics Data System (ADS)

Odenwald, Sten F.; Green, James L.

2007-06-01

We calculate the economic impact on the existing geosynchronous Earth-orbiting satellite population of an 1859-caliber superstorm event were it to occur between 2008 and 2018 during the next solar activity cycle. From a detailed model for transponder capacity and leasing, we have investigated the total revenue loss over the entire solar cycle, as a function of superstorm onset year and intensity. Our Monte Carlo simulations of 1000 possible superstorms, of varying intensity and onset year, suggest that the minimum revenue loss could be of the order of 30 billion. The losses would be larger than this if more that 20 satellites are disabled, if future launch rates do not keep up with the expected rate of retirements, or if the number of spare transponders falls below ˜30%. Consequently, revenue losses can be significantly reduced below 30 billion if the current satellite population undergoes net growth beyond 300 units during Solar Cycle 24 and a larger margin of unused transponders is maintained.

Caliber Corrected Markov Modeling (C2M2): Correcting Equilibrium Markov Models.

PubMed

Dixit, Purushottam D; Dill, Ken A

2018-02-13

Rate processes are often modeled using Markov State Models (MSMs). Suppose you know a prior MSM and then learn that your prediction of some particular observable rate is wrong. What is the best way to correct the whole MSM? For example, molecular dynamics simulations of protein folding may sample many microstates, possibly giving correct pathways through them while also giving the wrong overall folding rate when compared to experiment. Here, we describe Caliber Corrected Markov Modeling (C 2 M 2 ), an approach based on the principle of maximum entropy for updating a Markov model by imposing state- and trajectory-based constraints. We show that such corrections are equivalent to asserting position-dependent diffusion coefficients in continuous-time continuous-space Markov processes modeled by a Smoluchowski equation. We derive the functional form of the diffusion coefficient explicitly in terms of the trajectory-based constraints. We illustrate with examples of 2D particle diffusion and an overdamped harmonic oscillator.

Axonal Transport and Morphology: How Myelination gets Nerves into Shape

NASA Astrophysics Data System (ADS)

Jung, Peter; Zhao, Peng; Monsma, Paula; Brown, Tony

2011-03-01

The local caliber of mature axons is largely determined by neurofilament (NF) content. The axoskeleton, mainly consisting of NFs, however, is dynamic. NFs are assembled in the cell body and are transported by molecular motors on microtubule tracks along the axon at a slow rate of fractions of mm per day. We combine live cell fluorescent imaging techniques to access NF transport in myelinated and non-myelinated segments of axons with computational modeling of the active NF flow to show that a), myelination locally slows NF transport rates by regulating duty ratios and b), that the predicted increase in axon caliber agrees well with experiments. This study, for the first time, links NF kinetics directly to axonal morphology, providing a novel conceptual framework for the physical understanding of processes leading to the formation of axonal structures such as the ``Nodes of Ranvier'' as well as abnormal axonal swellings associated with neurodegenerative diseases like Amyotrophic lateral sclerosis (ALS). NSF grants # IOS-0818412(PJ) and IOS-0818653 (AB).

Perspective: Maximum caliber is a general variational principle for dynamical systems.

PubMed

Dixit, Purushottam D; Wagoner, Jason; Weistuch, Corey; Pressé, Steve; Ghosh, Kingshuk; Dill, Ken A

2018-01-07

We review here Maximum Caliber (Max Cal), a general variational principle for inferring distributions of paths in dynamical processes and networks. Max Cal is to dynamical trajectories what the principle of maximum entropy is to equilibrium states or stationary populations. In Max Cal, you maximize a path entropy over all possible pathways, subject to dynamical constraints, in order to predict relative path weights. Many well-known relationships of non-equilibrium statistical physics-such as the Green-Kubo fluctuation-dissipation relations, Onsager's reciprocal relations, and Prigogine's minimum entropy production-are limited to near-equilibrium processes. Max Cal is more general. While it can readily derive these results under those limits, Max Cal is also applicable far from equilibrium. We give examples of Max Cal as a method of inference about trajectory distributions from limited data, finding reaction coordinates in bio-molecular simulations, and modeling the complex dynamics of non-thermal systems such as gene regulatory networks or the collective firing of neurons. We also survey its basis in principle and some limitations.

27 CFR 447.42 - Application for permit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION IMPORTATION OF ARMS, AMMUNITION AND IMPLEMENTS OF... ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The length... the firearm, firearm barrel, ammunition, or other defense article to be imported; (K) The category of...

27 CFR 447.42 - Application for permit.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION IMPORTATION OF ARMS, AMMUNITION AND... ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The length... the firearm, firearm barrel, ammunition, or other defense article to be imported; (K) The category of...

27 CFR 447.42 - Application for permit.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION IMPORTATION OF ARMS, AMMUNITION AND... ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The length... the firearm, firearm barrel, ammunition, or other defense article to be imported; (K) The category of...

27 CFR 447.42 - Application for permit.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION IMPORTATION OF ARMS, AMMUNITION AND... ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The length... the firearm, firearm barrel, ammunition, or other defense article to be imported; (K) The category of...

27 CFR 447.42 - Application for permit.

Code of Federal Regulations, 2012 CFR

2012-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION IMPORTATION OF ARMS, AMMUNITION AND IMPLEMENTS OF... ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The length... the firearm, firearm barrel, ammunition, or other defense article to be imported; (K) The category of...

DEVELOPMENT OF THE SMALL AIRWAYS AND ALVEOLI FROM DHILDHOOD TO ADULT

EPA Science Inventory

Understanding the human development of pulmonary airspaces is important for calculating the dose from exposure to inhaled materials as a function of age. We have measured, in vivo, the airspace caliber of the small airways and alveoli by aerosol-derived airway morphometry (ADAM) ...

50 CFR 32.39 - Maryland.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or under) must remain within sight and normal voice contact of an adult age 18 or older. Children... caliber or larger with not less than 60 grains of black powder or a black powder equivalent. ii. We... shiner, eel, and sunfish (includes bluegill, black crappie, warmouth, and pumpkinseed). Maryland State...

Calculation of Weapon Platform Attitude and Cant using Available Sensor Feedback

DTIC Science & Technology

2018-02-01

terrain presents challenges for firing large caliber weapons. When a weapon is fired, the forward momentum of the discharge is equally reflected to the...GIDEP Operations Center P.O. Box 8000 Corona , CA 91718-8000 gidep@gidep.org UNCLASSIFIED Approved for public release; distribution

27 CFR 478.125a - Personal firearms collection.

Code of Federal Regulations, 2010 CFR

2010-04-01

... importer Model Serial No. Type Caliber or gauge Disposition Date Name and address (business address if... firearm was transferred from the business inventory into the personal collection or otherwise acquired as... receipt of the firearm into the business inventory or other acquisition, (3) The licensee recorded the...

22 CFR 121.4 - Ground vehicles.

Code of Federal Regulations, 2014 CFR

2014-04-01

... caliber); (2) Are armored support vehicles capable of off-road or amphibious use specially designed to... the definitions or control parameters regardless of the surface (e.g., highway, off-road, rail) upon...., different paint, repositioning of bolt holes), or that add parts or components otherwise available prior to...

50 CFR 32.20 - Alabama.

Code of Federal Regulations, 2012 CFR

2012-10-01

...). 5. We allow shotguns with #4 shot or smaller, rifles firing .22 caliber rimfire ammunition, or... State-approved hunter education course. One adult may supervise no more than two youths. 7. We prohibit.... One adult may supervise no more than one youth. 8. We prohibit participation in organized drives. D...

50 CFR 32.20 - Alabama.

Code of Federal Regulations, 2011 CFR

2011-10-01

...). 5. We allow shotguns with #4 shot or smaller, rifles firing .22 caliber rimfire ammunition, or... State-approved hunter education course. One adult may supervise no more than two youths. 7. We prohibit.... One adult may supervise no more than one youth. 8. We prohibit participation in organized drives. D...

50 CFR 32.20 - Alabama.

Code of Federal Regulations, 2010 CFR

2010-10-01

...). 5. We allow shotguns with #4 shot or smaller, rifles firing .22 caliber rimfire ammunition, or... State-approved hunter education course. One adult may supervise no more than two youths. 7. We prohibit.... One adult may supervise no more than one youth. 8. We prohibit participation in organized drives. D...

50 CFR 32.20 - Alabama.

Code of Federal Regulations, 2013 CFR

2013-10-01

...). 5. We allow shotguns with #4 shot or smaller, rifles firing .22 caliber rimfire ammunition, or... State-approved hunter education course. One adult may supervise no more than two youths. 7. We prohibit.... One adult may supervise no more than one youth. 8. We prohibit participation in organized drives. D...

Highly efficient orange and warm white phosphorescent OLEDs based on a host material with a carbazole-fluorenyl hybrid.

PubMed

Du, Xiaoyang; Huang, Yun; Tao, Silu; Yang, Xiaoxia; Wu, Chuan; Wei, Huaixin; Chan, Mei-Yee; Yam, Vivian Wing-Wah; Lee, Chun-Sing

2014-06-01

A new carbazole-fluorenyl hybrid compound, 3,3'(2,7-di(naphthaline-2-yl)-9H-fluorene-9,9-diyl)bis(9-phenyl-9H-carbazole) (NFBC) was synthesized and characterized. The compound exhibits blue-violet emission both in solution and in film, with peaks centered at 404 and 420 nm. In addition to the application as a blue emitter, NFBC is demonstrated to be a good host for phosphorescent dopants. By doping Ir(2-phq)3 in NFBC, a highly efficient orange organic light-emitting diode (OLED) with a maximum efficiency of 32 cd A(-1) (26.5 Lm W(-1)) was obtained. Unlike most phosphorescent OLEDs, the device prepared in our study shows little efficiency roll-off at high brightness and maintains current efficiencies of 31.9 and 26.8 cd A(-1) at a luminance of 1000 and 10,000 cd m(-2), respectively. By using NFBC simultaneously as a blue fluorescence emitter and as a host for a phosphorescent dopant, a warm white OLED with a maximum efficiency of 22.9 Lm W(-1) (21.9 cd A(-1)) was also obtained. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cross-directional interlocking of rolls in an air press of a papermaking machine

DOEpatents

Beck, David A.; Gorshe, Thomas

2003-05-13

An air press for pressing a paper web is composed of a plurality of rolls including at least a first roll and a second roll. The first roll and the second roll are positioned adjacent one another and form a first nip therebetween. Further, the first roll and the second roll each have a roll end, the roll end of the first roll adjoining the roll end of the second roll. A bevel plate is attached to the roll end of the first roll, the bevel plate having at least a first angled plate face. A seal ring is positioned adjacent the roll end of the second roll, the seal ring being juxtaposed to the bevel plate. The seal ring has at least a first angled ring face, and the first angled ring face mates with the first angled plate face.

Professional Development Which Provides an Icing on the Pedagogical Cake.

ERIC Educational Resources Information Center

Gardner, Jenny

Because the quality of teachers determines the quality of the school system, teachers must be provided with high-caliber inservice programs. During the 1980s, responsibility for the provision of professional development in Australia shifted to local schools. Under the current National Professional Development Program (NPDP), the Australian…

Parachute Recovery Systems Design Manual

DTIC Science & Technology

1991-03-01

CUTTER BLADE ’S ACTUATOR ASSEMBLY ASSEMBL WELDED CLOSURE DISK LINE BORON/CALCIUM CHROMATE 1OHM BRIDGE -. (47gm Dia. Wire Tophet C) DAP RING POLVIMIDE...8.124 J. A. Buckley. "Missile Recovery System for High-Speed Small-Caliber Missiles." AIAA Paper, October 1986. (AIAA 86-2462.) 8.125 S. K. Ibrahim

Reinventing the medical librarian.

PubMed Central

Anderson, R K

1989-01-01

The caliber of the librarian is a health sciences library's most important resource. This paper explores factors which have influenced who has, or who has not, entered the profession of medical librarianship, and discusses several attributes which the author considers critical for restructuring the profession to meet current and future needs. PMID:2790341

Transonic Compressor: Program System TXCO for Data Acquisition and On-Line Reduction.

DTIC Science & Technology

1980-10-01

IMONIDAYIYEARIHOUR,IMINISEC) OS16 C ............................................................... (0S17 C 0SiB C Gel dole ond line and convert the...linear curve fits SECON real intercept of linear curve fit (as from CURVE) 65 - . FLOW CHART SUBROUTINE CALIB - - - Aso C’A / oonre& *Go wSAt*irc

The Cognitive Science behind the Common Core

ERIC Educational Resources Information Center

Marchitello, Max; Wilhelm, Megan

2014-01-01

Raising academic standards has been part of the education policy discourse for decades. As early as the 1990s, states and school districts attempted to raise student achievement by developing higher standards and measuring student progress according to more rigorous benchmarks. However, the caliber of the standards--and their assessments--varied…

Controlled-force end seal arrangement for an air press of a papermaking machine

DOEpatents

Beck, David A.

2003-07-08

An air press for pressing a fiber web includes a plurality of rolls and a pair of end seal arrangements. Of the plurality of rolls, each pair of adjacent rolls forms a nip therebetween. Further, each roll has a pair of roll ends, the plurality of rolls together forming two sets of roll ends. Each end seal arrangement coacts with one set of roll ends, the plurality of rolls and the pair of end seal arrangements together defining an air press chamber having an air chamber pressure. Each end seal arrangement is composed of at least one roll seal, including a first roll seal, and an adjustable bias mechanism. Each roll seal forms a seal with at least one roll end, and one side of the first roll seal being exposed to the air chamber pressure. The adjustable bias mechanism is configured for controlling a position of each roll seal relative to a respective at least one roll end and for adjusting a seal force between the roll seal and the respective at least one roll end.

Development of ODS FeCrAl alloys for accident-tolerant fuel cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dryepondt, Sebastien N.; Hoelzer, David T.; Pint, Bruce A.

2015-09-18

FeCrAl alloys are prime candidates for accident-tolerant fuel cladding due to their excellent oxidation resistance up to 1400 C and good mechanical properties at intermediate temperature. Former commercial oxide dispersion strengthened (ODS) FeCrAl alloys such as PM2000 exhibit significantly better tensile strength than wrought FeCrAl alloys, which would alloy for the fabrication of a very thin (~250 m) ODS FeCrAl cladding and limit the neutronic penalty from the replacement of Zr-based alloys by Fe-based alloys. Several Fe-12-Cr-5Al ODS alloys where therefore fabricated by ball milling FeCrAl powders with Y2O3 and additional oxides such as TiO 2 or ZrO 2. Themore » new Fe-12Cr-5Al ODS alloys showed excellent tensile strength up to 800 C but limited ductility. Good oxidation resistance in steam at 1200 and 1400 C was observed except for one ODS FeCrAl alloy containing Ti. Rolling trials were conducted at 300, 600 C and 800 C to simulate the fabrication of thin tube cladding and a plate thickness of ~0.6mm was reached before the formation of multiple edge cracks. Hardness measurements at different stages of the rolling process, before and after annealing for 1h at 1000 C, showed that a thinner plate thickness could likely be achieved by using a multi-step approach combining warm rolling and high temperature annealing. Finally, new Fe-10-12Cr-5.5-6Al-Z gas atomized powders have been purchased to fabricate the second generation of low-Cr ODS FeCrAl alloys. The main goals are to assess the effect of O, C, N and Zr contents on the ODS FeCrAl microstructure and mechanical properties, and to optimize the fabrication process to improve the ductility of the 2nd gen ODS FeCrAl while maintaining good mechanical strength and oxidation resistance.« less

Wind-tunnel Tests of a Model of a Wingless Fin-controlled Missile to Obtain Static Stability and Control Characteristics Through a Range of Mach Numbers from 0.5 to 0.88

NASA Technical Reports Server (NTRS)

Burrows, Dale L; Newman, Ernest E

1954-01-01

An investigation at medium to high subsonic speeds has been conducted in the Langley low-turbulence pressure tunnel to determine the static stability and control characteristics and to measure the fin normal forces and moments for a model of a wingless fin-controlled missile. The data were obtained at Reynolds number of 2.1 x 10(6) based on the missile maximum diameter or 17.7 x 10(6) based on missile length; this Reynolds number was found to be large enough to avoid any large scale effects between the test and the expected flight Reynolds number. With the horizontal-fin deflection limited to a maximum of 6 degrees, longitudinally stable and trimmed flight could not be maintained beyond an angle of attack of 17 degrees for a Mach number of 0.88 and beyond 20 degrees for a Mach number of 0.50 for any center-of-gravity location without the use of some auxiliary stability or control device such as jet vanes. Mach number had no appreciable effect on the center-of-pressure positions and only a slight effect on neutral-point position. There was a shift in neutral-point position of about 1 caliber as the angle of attack was varied through the range for which the neutral point could be determined. Yawing the model to angles of sideslip up to 7 degrees had little effect on the longitudinal stability at angles of attack up to 15 degrees; however, above 15 degrees, the effect of sideslip was destabilizing. With the vertical fins at a plus-or-minus 6 degree roll deflection, the rolling moment caused by yawing the model at high angles of attack could be trimmed out up to angles of sideslip of 6.5 degrees and an angle of attack of 26 degrees for a Mach number of 0.50; this range of sideslip angles was reduced to 3 degrees at a Mach number of 0.88. The data indicated that, at lower angles of attack, the trim range extended to higher angles of sideslip. The total normal-force and hinge-moment coefficients for both horizontal fins were slightly nonlinear with both angle-of-attack and fin deflection. The effect of Mach number was to reduce the slopes of the hinge-moment coefficient with angle of attack and deflection angle. In general, the effort of increasing the sideslip angle was to reduce the values of the fin normal-force and hinge-moment coefficients.

Improvement of rolling 6 mm thin plates in plate rolling mill PT. Krakatau Posco

NASA Astrophysics Data System (ADS)

Pujiyanto, Hamdani

2017-01-01

A 6-mm thin plate is difficult to produce especially if the product requires wide size and high strength. Flatness is the main quality issue in rolling 6-mm plate using a 4-high reversing mill which use ±1100-mm work roll. Thus some methods are applied to overcome such issue in order to comply to customer quality requirement. Pre-rolling, rolling, and post-rolling conditions have to be considered comprehensively. Roll unit management will be the key factor before rolling condition. The roll unit itself has a significant impact on work roll crown wearness in relation with work roll intial crown and thermal crown. Work roll crown along with the modification of hydraulic gap control (HGC) could directly alter the flatness of the plate.

A Roll, Fin, and Fin Controller Prediction Computer Program.

DTIC Science & Technology

1980-06-01

IERATI *EQ. 03 WRITE16920301 ROLL 365 365 3R1TE(G. 26311 ROLL 366 no 505 ImU - 1,NNU ROLL 36? 50S WRITE(G.2011 3U(I’U),OAWPU(1PU,SIGLCfINU) ROLL 360...ROLL DAMPING WILL BE ONE**/$ ROLL 642 2016 FORMAT (/jIX,*LONGCRESTEO SVECTRA AND COMPONENTS WILL SE PRINTED. ROLL 44S 2’) ROLL 444 2019 FORMAT (1/19

DEVELOPMENT OF THE HUMAN LUNG MEASURED BY AEROSOL-DERIVED AIRWAY MORPHEMETRY (ADAM).

EPA Science Inventory

We measured, in vivo, the airspace calibers of the small airways and alveoli by ADAM in the lungs of children of ages 6 to 18 years and adults aged 18 to 80 years. ADAM utilizes the gravitational settling time of inhaled monodisperse particles to infer the vertical distance to th...

Changes in Body Composition and Strength of Female Athletes on Two Different Training Programs.

ERIC Educational Resources Information Center

Oyster, Nancy

Thirty-one championship caliber women athletes participating on varsity teams at Ohio State University were trained using two different conditioning programs, in an attempt to determine the physiological outcomes of weight training versus cardiovascular-oriented conditioning. Fourteen tennis players followed a program of high-resistance weight…

The Relationship of Leadership Practices on Teacher Morale and School Performance in Elementary Schools

ERIC Educational Resources Information Center

Howard, Mary Frances.

2012-01-01

The nation's K-12 schools are faced with critical challenges: elevating academic achievement, recruiting high-caliber teachers, engaging parental involvement and at-risk students. The national and global economic crisis has significantly compounded these challenges (Fullan, 2002; McEwan, 2003; Kowalski, 2008). School leaders are mandated by…

27 CFR 478.112 - Importation by a licensed importer.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) The type (e.g., rifle, shotgun, pistol, revolver and, in the case of ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The barrel length, if a firearm or... statement describing such intended use; or (C) If an unserviceable firearm (other than a machine gun) being...

27 CFR 478.113 - Importation by other licensees.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) The type (e.g., rifle, shotgun, pistol, revolver and, in the case of ammunition only, ball, wadcutter, shot, etc.); (C) The caliber, gauge, or size; (D) The model; (E) The barrel length, if a firearm or... machine gun) being imported as a curio or museum piece, a description of how it was rendered unserviceable...

DEVELOPMENT OF THE SMALL AIRWAYS AND ALVEOLI FROM CHILDHOOD TO ADULT LUNG MEASURED BY AEROSOL-DERIVED AIRWAY MORPHOMETRY

EPA Science Inventory

Understanding the human development of pulmonary airspaces is important for calculating the dose from exposure to inhaled materials as a function of age. We have measured, in vivo, the airspace caliber of the small airways and alveoli by aerosol-derived airway morphometry (ADAM) ...

DCPS Effective Schools Framework

ERIC Educational Resources Information Center

District of Columbia Public Schools, 2009

2009-01-01

DCPS is committed to providing "all" students with the caliber of education they deserve. The goal of the DCPS Effective Schools Framework is to ensure that every child, in every classroom, has access to a high-quality and engaging standards-based instructional program, and that all school supports are aligned to support teaching and learning. The…

49 CFR 173.56 - New explosives-definition and procedures for classification and approval.

Code of Federal Regulations, 2012 CFR

2012-10-01

... agency the ranges of composition of ingredients and compounds, showing the intended manufacturing... was produced to an explosives testing range if— (1) It is not a primary (a 1.1A initiating) explosive...) Ammunition with inert projectile or blank ammunition; and (4) Ammunition not exceeding 50 caliber for rifle...

49 CFR 173.56 - New explosives-definition and procedures for classification and approval.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the ranges of composition of ingredients and compounds, showing the intended manufacturing tolerances... was produced to an explosives testing range if— (1) It is not a primary (a 1.1A initiating) explosive...; (3) Ammunition with inert projectile or blank ammunition; and (4) Ammunition not exceeding 50 caliber...

49 CFR 173.56 - New explosives-definition and procedures for classification and approval.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the ranges of composition of ingredients and compounds, showing the intended manufacturing tolerances... was produced to an explosives testing range if— (1) It is not a primary (a 1.1A initiating) explosive...; (3) Ammunition with inert projectile or blank ammunition; and (4) Ammunition not exceeding 50 caliber...

49 CFR 173.56 - New explosives-definition and procedures for classification and approval.

Code of Federal Regulations, 2011 CFR

2011-10-01

... agency the ranges of composition of ingredients and compounds, showing the intended manufacturing... was produced to an explosives testing range if— (1) It is not a primary (a 1.1A initiating) explosive...) Ammunition with inert projectile or blank ammunition; and (4) Ammunition not exceeding 50 caliber for rifle...

Strength in Numbers: Balancing Institutional Identity with the Benefits of Consortium Membership

ERIC Educational Resources Information Center

Collins, Mary Ellen

2012-01-01

All college and university communications professionals work hard to promote their institutions' strengths and uniqueness. They tout high-caliber faculty, programs, and facilities and point to the achievements of their graduates as examples of their success. But those who work for institutions that are members of a higher education consortium also…

Meeting the Teacher Shortage Head On.

ERIC Educational Resources Information Center

Vollmer, Marian L.; And Others

The University of Pittsburgh has exerted concerted efforts to attract and retain liberal arts majors in teacher education, and insure high caliber graduates from its training program. One such program geared to upgrading the professional quality of its graduates is the Master of Arts in Teaching (MAT) program at the University's laboratory school.…

Clinical Cognition and Diagnostic Error: Applications of a Dual Process Model of Reasoning

ERIC Educational Resources Information Center

Croskerry, Pat

2009-01-01

Both systemic and individual factors contribute to missed or delayed diagnoses. Among the multiple factors that impact clinical performance of the individual, the caliber of cognition is perhaps the most relevant and deserves our attention and understanding. In the last few decades, cognitive psychologists have gained substantial insights into the…

Environmental Impact: Reinforce a Culture of Continuous Learning with These Key Elements

ERIC Educational Resources Information Center

Edwards, Brian; Gammell, Jessica

2017-01-01

Fostering a robust professional learning culture in schools is vital for attracting and retaining high-caliber talent. Education leaders are looking for guidance on how to establish and sustain an environment that fosters continuous learning. Based on their experience in helping educators design and implement professional learning systems, the…

Relationship between Leadership Behaviors of High School Principals and Teacher Retention in Texas

ERIC Educational Resources Information Center

Aiken, Debra L.

2010-01-01

The study investigated the relationship between leadership behaviors of high school principals and teacher retention in Texas. A total of 88 Texas high school principals participated in the survey. Leadership behaviors were measured using the Culturally Adapted Leadership for Inspired Business Excellence and Results (CALIBER) Leadership Assessment…

50 CFR 32.43 - Mississippi.

Code of Federal Regulations, 2010 CFR

2010-10-01

... complete the reverse side of the card and deposit it at one of the hunter information stations. Include all... nontoxic shotgun shot (see § 32.2(k)) and .22 caliber rifles. We prohibit all handguns. 4. All hunters or.... You must only use portable or temporary blinds. 3. You may only possess approved nontoxic shot (see...

50 CFR 32.39 - Maryland.

Code of Federal Regulations, 2014 CFR

2014-10-01

... approved nontoxic shot while in the field (see § 32.2(k)), except for the use of .22-caliber rimfire rifles... shot or vertical bows. 8. We select turkey hunters by a computerized lottery for youth, disabled, and.... We allow take of one chain pickerel per day. iii. Anglers must release all bass that they catch. 13...

14 CFR 417.125 - Launch of an unguided suborbital launch vehicle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... elevation angle setting that ensures the rocket will not fly uprange. A launch operator must set the... throughout each stage of powered flight. A caliber, for a rocket configuration, is defined as the distance... rocket configuration. (f) Tracking. A launch operator must track the flight of an unguided suborbital...

14 CFR 417.125 - Launch of an unguided suborbital launch vehicle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... elevation angle setting that ensures the rocket will not fly uprange. A launch operator must set the... throughout each stage of powered flight. A caliber, for a rocket configuration, is defined as the distance... rocket configuration. (f) Tracking. A launch operator must track the flight of an unguided suborbital...

14 CFR 417.125 - Launch of an unguided suborbital launch vehicle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... elevation angle setting that ensures the rocket will not fly uprange. A launch operator must set the... throughout each stage of powered flight. A caliber, for a rocket configuration, is defined as the distance... rocket configuration. (f) Tracking. A launch operator must track the flight of an unguided suborbital...

14 CFR 417.125 - Launch of an unguided suborbital launch vehicle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... elevation angle setting that ensures the rocket will not fly uprange. A launch operator must set the... throughout each stage of powered flight. A caliber, for a rocket configuration, is defined as the distance... rocket configuration. (f) Tracking. A launch operator must track the flight of an unguided suborbital...

14 CFR 417.125 - Launch of an unguided suborbital launch vehicle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... elevation angle setting that ensures the rocket will not fly uprange. A launch operator must set the... throughout each stage of powered flight. A caliber, for a rocket configuration, is defined as the distance... rocket configuration. (f) Tracking. A launch operator must track the flight of an unguided suborbital...

Nature Studies

ERIC Educational Resources Information Center

Hall, Barbara

2007-01-01

This article describes an upstate school in New York that integrates animals into their curriculum. Milbrook School has all the usual classes one might expect at a high-caliber private high school. Millbrook is a school with a zoo in its center. Or maybe it's more accurately described as a zoo surrounded by a school. Either way, it's an unusual…

[A new model of varicose vein stripper (author's transl)].

PubMed

Pelissier, E; Meyer, J M; Arbez, C

1982-05-22

A new varicose vein stripper is described. It is rigid, of small caliber and can be used in both upper and lower limbs. These features make it easy to handle, particularly in young subjects undergoing early stripping. The instrument is less costly than other disposable instruments as it is metallic and can be sterilized.

Microstructures and Mechanical Properties of 12Cr1MoVG Tube Welded Joints With/Without Post-weld Heat Treatment

NASA Astrophysics Data System (ADS)

Wang, Jingjing; Sun, Jian; Yu, Xinhai; Chen, Guohong; Fu, Qiuhua; Gao, Chao; Tang, Wenming

2017-10-01

Small-caliber, thick-wall 12Cr1MoVG seamless steel tube welded joints were fabricated in this study by gas tungsten arc welding and shielded metal arc welding techniques, then the microstructures, mechanical properties, and residual stress distributions of the joints with or without post-weld heat treatment (PWHT) were compared. The welded joints are mainly composed of bcc ferrite (F), Fe3C, and M7C3 carbides. PWHT did not cause an apparent microstructure evolution in the joints, but promoted granular pearlite decomposition and growth of F grains and carbides, therefore decreasing the yield, tensile strength, and hardness while increasing the impact toughness and elongation of the welded joints. PWHT also released the circumferential residual stress and altered the stress state in the joint from tensile to compressive. Although the mechanical properties and bending performance of the small-caliber, thick-wall 12Cr1MoVG seamless welded joints without PWHT are acceptable, our results show that the joints with PWHT are more reliable.

Health-hazard evaluation report HETA-91-161-2225, Denver Police Department, Denver, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.A.; McCammon, C.S.

1992-05-01

In response to a request from the Denver Police Department (SIC-9221) in Denver, Colorado, an investigation was made into lead (7439921) exposures during the use of different ammunition on the firing range. Ventilation rates were measured and personal breathing zone air samples were collected for ten officers during the firing of .45 caliber pistols. Nonlead primers were not yet available for .45 caliber ammunition. Air lead exposure ranged from 1.0 to 16 micrograms/cubic meter (microg/cu m). A slight improvement was noted in ventilation since an earlier NIOSH study had been performed at this site. The improvement resulted from the removalmore » of a 3 foot high partition along the floor on the firing line. There was still, however, turbulent air flow across the entire firing line and backflow in some of the shooting booths. The author concludes that there was no health hazard from lead overexposure at this site at this time, but recommends use of jacketed bullets, nonlead primers, and administrative controls to minimize lead exposures.« less

[An experimental study of the healing of velour grafts].

PubMed

Kobayashi, O

1986-02-01

An experimental study of implantation of velour grafts in the abdominal aorta or the external iliac artery of dogs was conducted with the object of evaluating the type of velour surface best fit for small-caliber artery implantation. Velour grafts measuring 4mm in diameter with differing velour surfaces were used as materials. Velour grafts now available on the market differ not only in velour surface but also in structure, notably in porosity and wall thickness. Hence each of the grafts used was reversed (i.e. inside out) and thus new grafts were prepared. These grafts were considered most suitable for making a comparative study of the effects of velour surface on healing. Macroscopic and histological findings revealed that each graft was good healing with the rate of patency as high as 84 percent. However, like Vasculour-D grafts, crimped grafts which preserve the crimp after implantation was significantly thicker at the internal valley than other grafts. Based on the findings of this experimental study non-crimped velour grafts were considered to be best fit for small-caliber artery implantation.

Ureteroscopy and stone lithotripsy with lithoclast: personal experience.

PubMed

Leidi, G L; Berti, G L; Canclini, L; Giola, V; Maccaroni, A; Raimoldi, A; Veneroni, L; Bacchioni, A M

1997-06-01

Ureteroscopy has become a common technique in the diagnosis and treatment of ureteral pathologies, but this procedure is quite invasive and some complications have been reported in literature. In our Institute 49 patients underwent ureteroscopy and ballistic lithotripsy with lithoclast for ureteral stones. The stones were localized both in the middle and distal part of the ureter. We used a small caliber 7-8.5 Wolf ureteroscope. The treatments were performed under antibiotic prophylaxis. Direct access to the ureter without dilation of the meatus was obtained in 97.96% of patients. The stones were easily reached in 93.88% of the cases and satisfactory fragmentation was obtained in 90.7%. In 4 patients (9.3%) one or more large stone fragments escaped into the kidney, requiring the patients to be treated with ESWL. No major complications occurred: no ureteral perforations, no important bleeding and no severe or persistent infections. All patients were discharged in one to four days postoperatively. The authors conclude that ureteroscopy using small caliber instruments with Lithoclast is a safe and satisfactory alternative to ESWL in the treatment of ureteral stones.

Propellant combustion product analyses on an M16 rifle and a 105 mm caliber gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ase, P.; Eisenberg, W.; Gordon, S.

1985-01-01

Some of the propellant combustion products (particulates and gases) that are formed on firing an M16 rifle and 105 mm caliber gun have been subjected to qualitative, and to a more limited extent, quantitative chemical analyses. For both weapons, large numbers of trace gas species, 90 to 70 respectively, were identified in the combustion effluents from the small large bore weapons. Quantifiable data were obtained for 15 of these species in terms of mass of compound formed per unit mass of propellant burned. Polynuclear aromatic hydrocarbons, 11 and 4 respectively, were identified and quantified in the combustion products from themore » small and large bore weapons. Metal particulates in the respirable range in the combustion products from the M16 rifle were analyzed and quantified. Many of the chemical species identified in the study have known toxicological properties. Although the data base is limited, it appears that within the confines of the different propellants' stoichiometries, the amounts of combustion products formed are approximately directly proportional to the masses of propellant burned.« less

[Alteration of textilfibres by explosion gases expelled distant from the muzzle (author's transl)].

PubMed

Bonte, W; Kijewski, H

1976-03-24

This paper presents the reconstruction of an unusual case of suicide. After raiding a branch-bank a robber fled shooting with his Sauer-Western revolver caliber .44 magnum at the pursuing policemen and succeeded in wrestling a pistol Walther caliber 7,65 mm from them. Under the fire of sub-machine guns he destroyed himself by a shot to the neck. Our investigations concerned a textile damage at the front of the sweater of the deceased surrounded by primer residue, showing characteristics of a close-up shot. The damage was identified as effect of explosion gases exhausting far-off the muzzle. The distance between this injury and the bullet hole corresponded with the length of the barrel of the Sauer-Western revolver and could be used for identification; it confirmed the diagnosis of a close-up shot at the neck, too. Collateral experiments with shots from distant ranges developed spadiceous melt figures of textile fibers around the bullet hole, the appearance of which is considered proof for a close-up shot commonly.

Myeloid Wnt ligands are required for normal development of dermal lymphatic vasculature.

PubMed

Muley, Ajit; Odaka, Yoshi; Lewkowich, Ian P; Vemaraju, Shruti; Yamaguchi, Terry P; Shawber, Carrie; Dickie, Belinda H; Lang, Richard A

2017-01-01

Resident tissue myeloid cells play a role in many aspects of physiology including development of the vascular systems. In the blood vasculature, myeloid cells use VEGFC to promote angiogenesis and can use Wnt ligands to control vascular branching and to promote vascular regression. Here we show that myeloid cells also regulate development of the dermal lymphatic vasculature using Wnt ligands. Using myeloid-specific deletion of the WNT transporter Wntless we show that myeloid Wnt ligands are active at two distinct stages of development of the dermal lymphatics. As lymphatic progenitors are emigrating from the cardinal vein and intersomitic vessels, myeloid Wnt ligands regulate both their numbers and migration distance. Later in lymphatic development, myeloid Wnt ligands regulate proliferation of lymphatic endothelial cells (LEC) and thus control lymphatic vessel caliber. Myeloid-specific deletion of WNT co-receptor Lrp5 or Wnt5a gain-of-function also produce elevated caliber in dermal lymphatic capillaries. These data thus suggest that myeloid cells produce Wnt ligands to regulate lymphatic development and use Wnt pathway co-receptors to regulate the balance of Wnt ligand activity during the macrophage-LEC interaction.

Sensory characterisation and consumer acceptability of potassium chloride and sunflower oil addition in small-caliber non-acid fermented sausages with a reduced content of sodium chloride and fat.

PubMed

Mora-Gallego, Héctor; Guàrdia, Maria Dolors; Serra, Xavier; Gou, Pere; Arnau, Jacint

2016-02-01

The effect of the simultaneous reduction of fat proportion (from 20% to 10% and 7%) and added salt (from 2.5% to 1.5%) and the subsequent addition of 0.64% KCl and sunflower oil (1.5% and 3.0%) on the physicochemical, instrumental colour and texture, sensory properties and consumer acceptability of small caliber non-acid fermented sausages (fuet type) was studied. This simultaneous reduction of fat and salt increased weight loss, moisture, water activity (aw), redness, instrumental texture parameters (hardness, chewiness and cohesiveness), sensory attributes (darkness, hardness, elasticity) and the consumer acceptability. The subsequent addition of 0.64% KCl to the leanest batch decreased the aw and barely affected instrumental texture parameters and consumer acceptability. Subsequent sunflower oil addition decreased hardness, chewiness and cohesiveness and increased crumbliness and oil flavour which may decrease the consumer acceptability. The simultaneous reduction of fat and NaCl with the addition of 0.64% KCl was the preferred option by the consumers. Copyright © 2015 Elsevier Ltd. All rights reserved.

CONTROL FOR ROLLING MILL

DOEpatents

Shuck, A.B.; Shaw, W.C.

1961-06-20

A plutonium-rolling apparatus is patented that has two sets of feed rolls, shaping rolls between the feed rolls, and grippers beyond the feed rolls, which ready a workpiece for a new pass through the shaping rolls by angularly shifting the workpiece about its axis or transversely moving it on a line parallel to the axes of the shaping rolls. Actuation of each gripper for gripping or releasing the workpiece is produced by the relative positions assumed by the feed rolls adjacent to the gripper as the workpiece enters or leaves the feed rolls.

An experimental study for determining human discomfort response to roll vibration

NASA Technical Reports Server (NTRS)

Leatherwood, J. D.; Dempsey, T. K.; Clevenson, S. A.

1976-01-01

An experimental study using a passenger ride quality apparatus (PRQA) was conducted to determine the subjective reactions of passengers to roll vibrations. The data obtained illustrate the effect upon human comfort of several roll-vibration parameters: namely, roll acceleration level, roll frequency, and seat location (i.e., distance from axis of rotation). Results of an analysis of variance indicated that seat location had no effect on discomfort ratings of roll vibrations. The effect of roll acceleration level was significant, and discomfort ratings increased markedly with increasing roll acceleration level at all roll frequencies investigated. Of particular interest, is the fact that the relationship between discomfort ratings and roll acceleration level was linear in nature. The effect of roll frequency also was significant as was the interaction between roll acceleration level and roll frequency.

Experimental and Theoretical Study on Minimum Achievable Foil Thickness during Asymmetric Rolling

PubMed Central

Tang, Delin; Liu, Xianghua; Song, Meng; Yu, Hailiang

2014-01-01

Parts produced by microforming are becoming ever smaller. Similarly, the foils required in micro-machines are becoming ever thinner. The asymmetric rolling technique is capable of producing foils that are thinner than those produced by the conventional rolling technique. The difference between asymmetric rolling and conventional rolling is the ‘cross-shear’ zone. However, the influence of the cross-shear zone on the minimum achievable foil thickness during asymmetric rolling is still uncertain. In this paper, we report experiments designed to understand this critical influencing factor on the minimum achievable thickness in asymmetric rolling. Results showed that the minimum achievable thickness of rolled foils produced by asymmetric rolling with a rolling speed ratio of 1.3 can be reduced to about 30% of that possible by conventional rolling technique. Furthermore, the minimum achievable thickness during asymmetric rolling could be correlated to the cross-shear ratio, which, in turn, could be related to the rolling speed ratio. From the experimental results, a formula to calculate the minimum achievable thickness was established, considering the parameters cross-shear ratio, friction coefficient, work roll radius, etc. in asymmetric rolling. PMID:25203265

Characterizing Sediment Supply to Rivers: Effects of Lithology, Climate, Weathering and Erosion on Rock-fragment Abundance in Granitic, Hillslope Soils

NASA Astrophysics Data System (ADS)

Riebe, C. S.; Marshall, J. A.; Sklar, L. S.; Granger, D. E.

2008-12-01

River incision sets the pace of landscape evolution and so is crucial to linkages among climate, tectonics and topography. Theoretical and experimental studies indicate that bedrock river incision should be regulated by both the quantity and caliber of sediment supply, which together affect the availability and persistence of bed-scouring tools in the channel. Rates of sediment supply are now quantified routinely using cosmogenic- radionuclide-based (CRN) measurements of hillslope erosion rates. Although grain-size data are also measured routinely (e.g., as part of state and federal soil surveys), they are not widely available for soils with well-constrained rates of erosion and weathering. As a result, there is much to learn about how weathering and erosion interrelate to regulate grain-size distributions in hillslope soils. Moreover, we lack a strong empirical basis for investigating how the rate and caliber of sediment supply affect bedrock river incision in natural systems. Here we compare new grain-size data with existing CRN-based rates of erosion and weathering for a series of granitic soils at two climatically diverse sites in the Sierra Nevada, California. Our results indicate that the percentage of coarse material---which presumably becomes the bedload that abrades and lowers channels---varies significantly across each site. At the colder, wetter site, differences in grain size and soil depth are substantial, despite little variability in erosion rates; coarse material abundance appears to increase with the density of bedrock outcrops, which increases with hillslope gradients, according to previous work. At the hotter, drier site, where rates of erosion and weathering vary by 10-fold, soil thickness and texture and the abundance of outcrops do not vary systematically across the landscape. We speculate that the differences in soil development across our two sites partly reflect effects of small differences in the ratio of biotite to hornblende in the parent rock. We discuss implications for constraining the rate and caliber of sediment supply to rivers.

The Impact of Macronutrients on Retinal Microvasculature among Singapore Pregnant Women during the Mid-Late Gestation.

PubMed

Li, Ling-Jun; Ong, Peng Guan; Colega, Marjorelee T; Han, Chad Yixian; Chen, Ling Wei; Man Eyn Kidd, Ryan; Lamoureux, Ecosse; Gluckman, Peter; Kwek, Kenneth; Chong, Yap Seng; Saw, Seang Mei; Godfrey, Keith M; Wong, Tien Yin; Chong Foong-Fong, Mary

2016-01-01

Imbalanced macronutrient intakes can induce impairment of endothelial and vascular function, and further lead to metabolic and cardiovascular disease. However, little is known about the influence of such diets on endothelial and vascular dysfunction in pregnant women, even though high-fat diet is a known risk for pregnancy complications such as gestational diabetes and pre-eclampsia. We aimed to assess the association between maternal macronutrient intakes (protein, fat and carbohydrates), dietary quality and retinal microvascular changes in a multi-ethnic Asian mother-offspring cohort. Pregnant women (n = 614) with singleton pregnancies were recruited during their first trimester from June 2009 to Sep 2010. Maternal diet quality and macronutrient intakes, expressed as a percentage of total energy during pregnancy, were ascertained using 24 hr recalls and 3 d food diaries at 26-28 weeks gestation. Retinal examination was completed at the same clinic visit. Dietary quality was assessed and scored using the Health Eating Index in Asian Pregnant women (HEI-AP), while macronutrients intakes ware expressed as percentages of total energy and further log transformed for analysis. Associations were examined cross-sectionally by substitution models with the use of multiple linear regression. In adjusted model, each 20 points decrease in HEI-AP score was associated with a significant increase of 1.70 μm (p<0.05) in retinal venular calibre. Each 0.1 log increase in percentage of total fat intake was associated with a significant increment of 1.84 μm (p<0.05) in retinal venular caliber. Additionally, each 0.1 log increase in percentage of mono-unsaturated fat intake was associated with an increment of 1.84 μm (p<0.01) in retinal venular caliber. In this cross-sectional study, we found that women with higher fat and lower protein intakes, and lower diet quality tended to have wider retinal venular caliber, which is suggestive of suboptimal microvasculature.

The Impact of Macronutrients on Retinal Microvasculature among Singapore Pregnant Women during the Mid-Late Gestation

PubMed Central

Li, Ling-Jun; Ong, Peng Guan; Colega, Marjorelee T.; Han, Chad Yixian; Chen, Ling Wei; Man Eyn Kidd, Ryan; Lamoureux, Ecosse; Gluckman, Peter; Kwek, Kenneth; Chong, Yap Seng; Saw, Seang Mei; Godfrey, Keith M.; Wong, Tien Yin; Chong Foong-Fong, Mary

2016-01-01

Background Imbalanced macronutrient intakes can induce impairment of endothelial and vascular function, and further lead to metabolic and cardiovascular disease. However, little is known about the influence of such diets on endothelial and vascular dysfunction in pregnant women, even though high-fat diet is a known risk for pregnancy complications such as gestational diabetes and pre-eclampsia. Objective We aimed to assess the association between maternal macronutrient intakes (protein, fat and carbohydrates), dietary quality and retinal microvascular changes in a multi-ethnic Asian mother-offspring cohort. Methods Pregnant women (n = 614) with singleton pregnancies were recruited during their first trimester from June 2009 to Sep 2010. Maternal diet quality and macronutrient intakes, expressed as a percentage of total energy during pregnancy, were ascertained using 24 hr recalls and 3 d food diaries at 26–28 weeks gestation. Retinal examination was completed at the same clinic visit. Dietary quality was assessed and scored using the Health Eating Index in Asian Pregnant women (HEI-AP), while macronutrients intakes ware expressed as percentages of total energy and further log transformed for analysis. Associations were examined cross-sectionally by substitution models with the use of multiple linear regression. Results In adjusted model, each 20 points decrease in HEI-AP score was associated with a significant increase of 1.70 μm (p<0.05) in retinal venular calibre. Each 0.1 log increase in percentage of total fat intake was associated with a significant increment of 1.84 μm (p<0.05) in retinal venular caliber. Additionally, each 0.1 log increase in percentage of mono-unsaturated fat intake was associated with an increment of 1.84 μm (p<0.01) in retinal venular caliber. Conclusions In this cross-sectional study, we found that women with higher fat and lower protein intakes, and lower diet quality tended to have wider retinal venular caliber, which is suggestive of suboptimal microvasculature. PMID:27508392

Environmentally Benign Stab Detonators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gash, A

2005-12-21

Many energetic systems can be activated via mechanical means. Percussion primers in small caliber ammunition and stab detonators used in medium caliber ammunition are just two examples. Current medium caliber (20-60mm) munitions are detonated through the use of impact sensitive stab detonators. Stab detonators are very sensitive and must be small, as to meet weight and size limitations. A mix of energetic powders, sensitive to mechanical stimulus, is typically used to ignite such devices. Stab detonators are mechanically activated by forcing a firing pin through the closure disc of the device and into the stab initiating mix. Rapid heating causedmore » by mechanically driven compression and friction of the mixture results in its ignition. The rapid decomposition of these materials generates a pressure/temperature pulse that is sufficient to initiate a transfer charge, which has enough output energy to detonate the main charge. This general type of ignition mix is used in a large variety of primers, igniters, and detonators.[1] Common primer mixes, such as NOL-130, are made up of lead styphnate (basic) 40%, lead azide (dextrinated) 20%, barium nitrate 20%, antimony sulfide 15%, and tetrazene 5%.[1] These materials pose acute and chronic toxicity hazards during mixing of the composition and later in the item life cycle after the item has been field functioned. There is an established need to replace these mixes on toxicity, health, and environmental hazard grounds. This effort attempts to demonstrate that environmentally acceptable energetic solgel coated flash metal multilayer nanocomposites can be used to replace current impact initiated devices (IIDs), which have hazardous and toxic components. Successful completion of this project will result in IIDs that include innocuous compounds, have sufficient output energy for initiation, meet current military specifications, are small, cost competitive, and perform as well as or better than current devices. We expect flash metal multilayer and sol-gel to be generic technologies applicable to a wide range of devices, especially in small caliber ammunition and sub-munitions. We will replace the NOL-130 mixture with a nanocomposite that consists of a mechanically robust energetic multilayer foil that has been coated with a sol-gel energetic material. The exothermic reactions are activated in this nanocomposite are the transformation of the multilayer material to its respective intermetallic alloy and the thermite reaction, which is characterized by very high temperatures, a small pressure pulse, and hot particle ejection. The proposed materials and their reaction products consist of, but are not limited to aluminum, nickel, iron, aluminum oxide, titanium, iron oxide and boron. These materials have much more desirable environmental and health characteristics than the NOL-130 composition.« less

Microstructural and mechanical responses to various rolling speeds determined in multi-pass break-down rolling of AZ31B alloy

NASA Astrophysics Data System (ADS)

Jia, Weitao; Tang, Yan; Ning, Fangkun; Le, Qichi; Cui, Jianzhong

2018-04-01

Different rolling operations of as-cast AZ31B alloy were performed under different rolling speed (18 ∼ 72 m min‑1) and rolling pass conditions at 400 °C. Microstructural studies, tensile testing and formability evaluation relevant to each rolling operation were investigated. For 1-pass rolling, coarse average grain size (CAGS) region gradually approached the center layer as the rolling speed increased. Moreover, twins, shear bands and coarse-grain structures were the dominant components in the microstructure of plates rolled at 18, 48 and 72 m min‑1, respectively, indicating the severe deformation inhomogeneity under the high reduction per pass condition. For 2-pass rolling and 4-pass rolling, dynamic recrystallization was observed to be well and CAGS region has substantially disappeared, indicating the significant improvement in deformation uniformity and further the grain homogenization under the conditions. Microstructure uniformity degree of 2-pass rolled plates did not vary much as the rolling speed varied. On this basis, shear band distribution dominated the deformation behavior during the uniaxial tension of the 2-pass rolled plates. However, microstructure uniformity accompanied by twin distribution played a leading role in stretching the 4-pass rolled plates.

75 FR 19369 - Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products from Brazil: Preliminary Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

...-Rolled Carbon Quality Steel Products from Brazil: Preliminary Results of Antidumping Duty Administrative... duty order on certain hot-rolled flat-rolled carbon quality steel products (hot-rolled steel) from... 1, 2008, through February 28, 2009. We preliminarily determine that the sale of hot-rolled steel...

75 FR 64246 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Correction to Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

...-Rolled Carbon-Quality Steel Products From Brazil: Correction to Notice of Antidumping Duty Order AGENCY... certain hot-rolled flat-rolled carbon-quality steel products from Brazil. See Antidumping Duty Order: Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, 67 FR 11093 (March 12, 2002...

Social Connectedness, Academic, Non-Academic Behaviors Related to Self-Regulation among University Students in Saudi Arabia

ERIC Educational Resources Information Center

Jdaitawi, Malek

2015-01-01

Studies dedicated to examination of self-regulation posit a bi-directional association between self-regulation and other variables including social connectedness, self-efficacy and self-control. However, to date, studies of this caliber have only evidenced that self-regulation is a predictor of other variables. In the present study, the factors…

Bed load transport in gravel-bed rivers

Treesearch

Jeffrey J. Barry

2007-01-01

Bed load transport is a fundamental physical process in alluvial rivers, building and maintaining a channel geometry that reflects both the quantity and timing of water and the volume and caliber of sediment delivered from the watershed. A variety of formulae have been developed to predict bed load transport in gravel-bed rivers, but testing of the equations in natural...

76 FR 10522 - Naval Surface Warfare Center, Upper Machodoc Creek and the Potomac River, Dahlgren, VA; Danger Zone

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-25

... small caliber guns and projectiles, aerial bombing, directed energy technology, and manned or unmanned... at 202- 761-4922 or by e-mail at [email protected] , or Mr. Robert Berg, Corps of Engineers, Norfolk District, Regulatory Branch, at 757- 201-7793 or by e-mail at [email protected

Social Work Program Review: State University System of Florida. Consultant's Report and Recommendations.

ERIC Educational Resources Information Center

Khinduka, Shanti K.

This review of graduate and undergraduate social work degree programs in the State University System of Florida (SUS) focuses on quality of curriculum, composition and caliber of students and faculty, nature and adequacy of facilities and resources, and overall progress of social work education since the previous program review in 1988. Florida…

Examination of a Wear-Reducing Muzzle Device

DTIC Science & Technology

2013-08-01

resistant material attached to the muzzle end of the gun tube. The bore diameter of the device is slightly less than the bore diameter of the gun. The...3  Figure 3. Weapon and universal bearing slide used for firings ...small caliber round of ammunition. ..........21  v List of Tables Table 1. Firing test matrix for phase 1

Grab a MOOC by the Horns

ERIC Educational Resources Information Center

Lokey-Vega, Anissa

2014-01-01

MOOCs (Massive Open Online Courses) have been barreling through the field of higher education since the first MOOC was launched in 2008. These free courses were initially believed to be a way to provide a high-caliber education to anyone with Internet access and a will to learn. Although research so far has shown that MOOCs aren't living up…

Cracking the Code of Effective Learning through Management of Learning Experiences

ERIC Educational Resources Information Center

Al-Fuqaha, Isam Najib

2016-01-01

This article is an attempt to explore why the efforts of universities fall short of accomplishing their objectives, and fail to improve the caliber of their graduates, as large numbers of them are unable to encounter real-life problems. It also probes the relations between four independent demographic variables (gender, age, experience, and…

Using a Two-Factor Framework to Optimize Online Students' Satisfaction While Minimizing Their Dissatisfaction

ERIC Educational Resources Information Center

Watson, Firm Faith Saint Annie

2016-01-01

Students' satisfaction is a very important indicator of the caliber of online courses, a learning modality which has escalated in the last decade. Satisfaction, however, is a complex construct and most related studies assume that satisfaction is the opposite of dissatisfaction. An alternative view from the area of organizational psychology was…

Information Seeking about the Military by Young Men: Findings from the 1989 Youth Attitude Tracking Study II

DTIC Science & Technology

1991-02-01

its use of high technologies and its high-caliber tram- ing in a very demanding electronic environment. The Navy’s advertising strategy is similar to...element of their advertising strategy is the use of direct mail campaigns. The content of broadcast and direct mail advertising messages often

The Development of Tactical Leadership Exercises for SIMCAT

DTIC Science & Technology

1987-07-01

Weapon Station (CWS) "* Engage Targets with a Caliber .50 Machinegun "* Fire the M239 or the M250 Grenade Launcher Other Tasks. The following tasks cannot...commander’s weapon station (CWS). - Engage targets with the coaxial machinegun from the commander’s weapon station (CWS). Fire the M239 or the M250 grenade

High speed metal removal

NASA Astrophysics Data System (ADS)

Pugh, R. F.; Pohl, R. F.

1982-10-01

Four types of steel (AISI 1340, 4140, 4340, and HF-1) which are commonly used in large caliber projectile manufacture were machined at different hardness ranges representing the as-forged and the heat treated condition with various ceramic tools using ceramic coated tungsten carbide as a reference. Results show that machining speeds can be increased significantly using present available tooling.

Ultra-high surface speed for metal removal, artillery shell

NASA Astrophysics Data System (ADS)

Pugh, R. F.; Walsh, M. R.; Pohl, R. F.

1981-07-01

Four types of steel (AISI 1340, 4140, 4340, and HF-1) which are commonly used in large caliber projectile manufacture were machined with five types of tools at different hardness ranges representing the as-forged and the heat-treated condition. Results show that machining speeds can be increased significantly over current practice using the present available tooling.

New Beginnings, New Limits: Education and the 1988 Presidential Election.

ERIC Educational Resources Information Center

Kaplan, George

1988-01-01

Schools have become fair game as a campaign issue but are not top priority. How the 41st president performs will hinge on the political estate of Ronald Reagan, the high voltage Washington political scene, and the caliber of the team staffing the new administration's education team. So far, the Education Department has failed as a believable…

The Safe Transport of Munitions (STROM) Program, Task 10 - The Use of Buffers, Other than Spacer Cars, in Preventing Propagation of Explosion Between Railcars

DTIC Science & Technology

1982-04-01

by as much as a projectile caliber seriously ^Gibbons, Gould, Ballistic Researsh Laboratory, private oommuniaation. 23 (D C 3 r—< • f) Ss.O...within neighboring railcars. These requirements constrain the materials and engineering approaches which are technically feasible. It is relatively

The Impact of Leadership Practices on the Academic Achievement of Elementary Students in Satisfactory Schools and Unsatisfactory Schools in Georgia

ERIC Educational Resources Information Center

Hill, Antonio

2011-01-01

Our nation's k-12 schools are faced with numerous critical challenges: elevating academic achievement, recruitment and retention of high-caliber teachers, improving teacher quality, and meeting the mandates of the "No Child Left Behind" ("NCLB") legislation and state standards (Simpson, Lacava, & Graner, 2004; &…

Cooperative Plane Strain Fracture Toughness Tests with C-Shaped Specimens

DTIC Science & Technology

1978-09-01

LABORATORY WATERVLIET, N. Y. 12189 — AMCMS No. 5397.OM.6350 PRON No. A1-8-P5276-AW-1A APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED...6350 PRON No. A1-8-P5276-AW-1A 11. CONTROLLING OFFICE NAME AND ADDRESS 12. US Army Armament Research and Development Commanjd Large Caliber

40th Annual Armament Systems: Guns-Ammunition-Rockets-Missiles Conference and Exhibition

DTIC Science & Technology

2005-04-28

Session: Medium Caliber System Oerlikon Ammunition for New Defense Environment, Mr. Allan N. Buckley, BTECH Oerlikon Contraves Pyrotec AG Multi...Environment Mr. Allan N. Buckley, BTECH Oerlikon Contraves Pyrotec AG Force Protection - Multi Mission Vehicle Armament & Air Burst Munition for...determine homogeneity – Propellant contains ~3% by weight of FS grains to adjust K

A Utilization-Focused Evaluation of a Community College Adjunct Faculty Professional Development Program

ERIC Educational Resources Information Center

Edenfield, Gordon

2010-01-01

Nationally adjunct faculty comprise almost 70% of all two-year institution faculty while in the Virginia Community College System (VCCS) adjunct faculty teach 60% of the community college courses, and should past trends continue, the number of adjunct faculty members is expected to grow 10% within the next fifteen years (Caliber, 2007; Phillipe…

Flow Disturbance Characterization Measurements in the National Transonic Facility

NASA Technical Reports Server (NTRS)

King, Rudolph A.; Andino, Marlyn Y.; Melton, Latunia; Eppink, Jenna; Kegerise, Michael A.; Tsoi, Andrew

2012-01-01

Recent flow measurements have been acquired in the National Transonic Facility (NTF) to assess the unsteady flow environment in the test section. The primary purpose of the test is to determine the feasibility of the NTF to conduct laminar-flow-control testing and boundary-layer transition sensitive testing. The NTF can operate in two modes, warm (air) and cold/cryogenic (nitrogen) test conditions for testing full and semispan scaled models. The warm-air mode enables low to moderately high Reynolds numbers through the use of high tunnel pressure, and the nitrogen mode enables high Reynolds numbers up to flight conditions, depending on aircraft type and size, utilizing high tunnel pressure and cryogenic temperatures. NASA's Environmentally Responsible Aviation (ERA) project is interested in demonstrating different laminar-flow technologies at flight-relevant operating conditions throughout the transonic Mach number range and the NTF is well suited for the initial ground-based demonstrations. Roll polar data at selected test conditions were obtained to look at the uniformity of the flow disturbance field in the test section. Data acquired from the rake probes included mean total temperatures, mean and fluctuating static/total pressures, and mean and fluctuating hot-wire measurements. . Based on the current measurements and previous data, an assessment was made that the NTF is a suitable facility for ground-based demonstrations of laminar-flow technologies at flight-relevant conditions in the cryogenic mode.

Moxibustion for Cephalic Version of Breech Presentation.

PubMed

Schlaeger, Judith M; Stoffel, Cynthia L; Bussell, Jeanie L; Cai, Hui Yan; Takayama, Miho; Yajima, Hiroyoshi; Takakura, Nobuari

2018-05-01

Moxibustion, a form of traditional Chinese medicine (TCM), is the burning of the herb moxa (Folium Artemisiae argyi or mugwort) over acupuncture points. It is often used in China to facilitate cephalic version of breech presentation. This article reviews the history, philosophy, therapeutic use, possible mechanisms of action, and literature pertaining to its use for this indication. For moxibustion, moxa can be rolled into stick form, placed directly on the skin, or placed on an acupuncture needle and ignited to warm acupuncture points. Studies have demonstrated that moxibustion may promote cephalic version of breech presentation and may facilitate external cephalic version. However, there is currently a paucity of research on the effects of moxibustion on cephalic version of breech presentation, and thus there is a need for further studies. Areas needing more investigation include efficacy, safety, optimal technique, and best protocol for cephalic version of breech presentation. © 2018 by the American College of Nurse-Midwives.

49 CFR 393.134 - What are the rules for securing roll-on/roll-off or hook lift containers?

Code of Federal Regulations, 2011 CFR

2011-10-01

... or hook lift containers? 393.134 Section 393.134 Transportation Other Regulations Relating to... for securing roll-on/roll-off or hook lift containers? (a) Applicability. The rules in this section apply to the transportation of roll-on/roll-off or hook lift containers. (b) Securement of a roll-on...

49 CFR 393.134 - What are the rules for securing roll-on/roll-off or hook lift containers?

Code of Federal Regulations, 2010 CFR

2010-10-01

... or hook lift containers? 393.134 Section 393.134 Transportation Other Regulations Relating to... for securing roll-on/roll-off or hook lift containers? (a) Applicability. The rules in this section apply to the transportation of roll-on/roll-off or hook lift containers. (b) Securement of a roll-on...

Rolling-Element Bearings

NASA Technical Reports Server (NTRS)

Hamrock, B. J.; Anderson, W. J.

1983-01-01

Rolling element bearings are a precision, yet simple, machine element of great utility. A brief history of rolling element bearings is reviewed and the type of rolling element bearings, their geometry and kinematics, as well as the materials they are made from and the manufacturing processes they involve are described. Unloaded and unlubricated rolling element bearings, loaded but unlubricated rolling element bearings and loaded and lubricated rolling element bearings are considered. The recognition and understanding of elastohydrodynamic lubrication covered, represents one of the major development in rolling element bearings.

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

NASA Technical Reports Server (NTRS)

Lahoti, G. D.; Akgerman, N.; Altan, T.

1978-01-01

Mild steel (AISI 1018) was selected as model cold-rolling material and Ti-6Al-4V and INCONEL 718 were selected as typical hot-rolling and cold-rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape-rolling process were developed. These models utilize the upper-bound and the slab methods of analysis, and are capable of predicting the lateral spread, roll-separating force, roll torque and local stresses, strains and strain rates. This computer-aided design (CAD) system is also capable of simulating the actual rolling process and thereby designing roll-pass schedule in rolling of an airfoil or similar shape. The predictions from the CAD system were verified with respect to cold rolling of mild steel plates. The system is being applied to cold and hot isothermal rolling of an airfoil shape, and will be verified with respect to laboratory experiments under controlled conditions.

Inflationary dynamics with a smooth slow-roll to constant-roll era transition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Odintsov, S.D.; Oikonomou, V.K., E-mail: odintsov@ieec.uab.es, E-mail: v.k.oikonomou1979@gmail.com

In this paper we investigate the implications of having a varying second slow-roll index on the canonical scalar field inflationary dynamics. We shall be interested in cases that the second slow-roll can take small values and correspondingly large values, for limiting cases of the function that quantifies the variation of the second slow-roll index. As we demonstrate, this can naturally introduce a smooth transition between slow-roll and constant-roll eras. We discuss the theoretical implications of the mechanism we introduce and we use various illustrative examples in order to better understand the new features that the varying second slow-roll index introduces.more » In the examples we will present, the second slow-roll index has exponential dependence on the scalar field, and in one of these cases, the slow-roll era corresponds to a type of α-attractor inflation. Finally, we briefly discuss how the combination of slow-roll and constant-roll may lead to non-Gaussianities in the primordial perturbations.« less

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

NASA Technical Reports Server (NTRS)

Lahoti, G. D.; Akgerman, N.; Altan, T.

1978-01-01

Mild steel (AISI 1018) was selected as model cold rolling material and Ti-6A1-4V and Inconel 718 were selected as typical hot rolling and cold rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape rolling process were developed. These models utilized the upper bound and the slab methods of analysis, and were capable of predicting the lateral spread, roll separating force, roll torque, and local stresses, strains and strain rates. This computer-aided design system was also capable of simulating the actual rolling process, and thereby designing the roll pass schedule in rolling of an airfoil or a similar shape.

A model for prediction of profile and flatness of hot and cold rolled flat products in four-high mills

NASA Astrophysics Data System (ADS)

Overhagen, Christian; Mauk, Paul Josef

2018-05-01

For flat rolled products, the thickness profile in the transversal direction is one of the most important product properties. For further processing, a defined crown of the product is necessary. In the rolling process, several mechanical and thermal influences interact with each other to form the strip shape at the roll gap exit. In the present analysis, a process model for rolling of strip and sheet is presented. The core feature of the process model is a two-dimensional stress distribution model based on von Karman's differential equation. Sub models for the mechanical influences of work roll flattening as well as work and backup roll deflection and the thermal influence of work roll expansion have been developed or extended. The two-dimensional stress distribution serves as an input parameter for the roll deformation models. For work roll flattening, a three-dimensional model based on the Boussinesq problem is adopted, while the work and backup roll deflection, including contact flattening is calculated by means of finite beam elements. The thermal work roll crown is calculated with help of an axisymmetric numerical solution of the heat equation for the work roll, considering azimuthal averaging for the boundary conditions at the work roll surface. Results are presented for hot rolling of a strip in a seven-stand finishing train of a hot strip mill, showing the calculated evolution of the strip profile. A variation of the strip profile from the first to the 20th rolled strip is shown. This variation is addressed to the progressive increase of work roll temperature during the first 20 strips. It is shown that a CVC® system can lead to improvements in strip profile and therefore flatness.

Finite-element model to predict roll-separation force and defects during rolling of U-10Mo alloys

NASA Astrophysics Data System (ADS)

Soulami, Ayoub; Burkes, Douglas E.; Joshi, Vineet V.; Lavender, Curt A.; Paxton, Dean

2017-10-01

A major goal of the Convert Program of the U.S. Department of Energy's National Nuclear Security Administration (DOE/NNSA) is to enable high-performance research reactors to operate with low-enriched uranium rather than the high-enriched uranium currently used. To this end, uranium alloyed with 10 wt% molybdenum (U-10Mo) represents an ideal candidate because of its stable gamma phase, low neutron caption cross section, acceptable swelling response, and predictable irradiation behavior. However, because of the complexities of the fuel design and the need for rolled monolithic U-10Mo foils, new developments in processing and fabrication are necessary. This study used a finite-element code, LS-DYNA, as a predictive tool to optimize the rolling process. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel were conducted following two different schedules. Model predictions of the roll-separation force and roll pack thicknesses at different stages of the rolling process were compared with experimental measurements. The study reported here discussed various attributes of the rolled coupons revealed by the model (e.g., waviness and thickness non-uniformity like dog-boning). To investigate the influence of the cladding material on these rolling defects, other cases were simulated: hot rolling with alternative can materials, namely, 304 stainless steel and Zircaloy-2, and bare-rolling. Simulation results demonstrated that reducing the mismatch in strength between the coupon and can material improves the quality of the rolled sheet. Bare-rolling simulation results showed a defect-free rolled coupon. The finite-element model developed and presented in this study can be used to conduct parametric studies of several process parameters (e.g., rolling speed, roll diameter, can material, and reduction).

Effect of Rolling Massage on the Vortex Flow in Blood Vessels with Lattice Boltzmann Simulation

NASA Astrophysics Data System (ADS)

Yi, Hou Hui

The rolling massage manipulation is a classic Chinese Medical Massage, which is a nature therapy in eliminating many diseases. Here, the effect of the rolling massage on the cavity flows in blood vessel under the rolling manipulation is studied by the lattice Boltzmann simulation. The simulation results show that the vortex flows are fully disturbed by the rolling massage. The flow behavior depends on the rolling velocity and the rolling depth. Rolling massage has a better effect on the flows in the cavity than that of the flows in a planar blood vessel. The result is helpful to understand the mechanism of the massage and develop the rolling techniques.

75 FR 62566 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... antidumping duty investigation on hot-rolled steel from Russia. SUMMARY: The Commission hereby gives notice of... suspended investigation on hot-rolled steel from Russia would be likely to lead to continuation or...

76 FR 34101 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

...] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia Determinations On...-quality steel products from Russia would be likely to lead to continuation or recurrence of material...) entitled Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil, Japan, and Russia: Investigation...

75 FR 16504 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-01

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... investigation on hot-rolled steel from Russia. SUMMARY: The Commission hereby gives notice that it has...-rolled steel from Russia would be likely to lead to continuation or recurrence of material injury...

75 FR 42782 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-22

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... Brazil and Japan, and the suspended investigation on hot-rolled steel from Russia. SUMMARY: The... Japan, and the suspended investigation on hot-rolled steel from Russia would be likely to lead to...

On the Influence of Surface Heterogeneities onto Roll Convection

NASA Astrophysics Data System (ADS)

Gryschka, M.; Drüe, C.; Raasch, S.; Etling, D.

2009-04-01

Roll convection is a common phenomenon in atmospheric convective boundary layers (CBL) with background wind. Roll convection is observed both over land and over sea for different synoptic situations. There is still some debate about the different types of roll convection and their causes or rather the necessary conditions for their appearance. The stability parameter ζ = -zi•L (zi: boundary layer height, L: Monin-Obukhov stability length) is widely used as a predictor for roll convection, since numerous studies suggest that convective rolls only appear when 0 < ζ < 20. In other words, roll development becomes unlikely for strong surface heating and weak vertical wind shear. In contrast to those studies the presence of roll convection in almost any polar cold air outbreak (as can be seen in numerous satellite images as cloud streets) reveals that even for large ζ roll convection can develop. Some studies report roll convection in cold air outbreaks for ζ = 250. Our large eddy simulations (LES) on roll convection suggests that the contrasting results concerning the dependency of roll convection on ζ are due to two different types of roll convection: One type which develops purely by self organization if ζ < 20 ("free rolls") and another type which is triggered by heterogeneities in surface temperature and develops also for large ζ ("forced rolls"). We think that most of the cloud streets observed in polar cold air outbreaks over open water are due to rolls of forced type which are tied to upstream located heterogeneities in the sea-ice distribution. The results of this study suggests that the omission of surface inhomogeneities in previous LES is the reason for the absence of rolls in all LES with strong surface heating and weak vertical wind shear so far. In this contribution we will present a large eddy simulation which successfully represents forced rolls under such conditions.

Static roll-tilt over 5 minutes locally distorts the internal estimate of direction of gravity.

PubMed

Tarnutzer, A A; Bockisch, C J; Straumann, D; Marti, S; Bertolini, G

2014-12-01

The subjective visual vertical (SVV) indicates perceived direction of gravity. Even in healthy human subjects, roll angle-dependent misestimations, roll overcompensation (A-effect, head-roll > 60° and <135°) and undercompensation (E-effect, head-roll < 60°), occur. Previously, we demonstrated that, after prolonged roll-tilt, SVV estimates when upright are biased toward the preceding roll position, which indicates that perceived vertical (PV) is shifted by the prior tilt (Tarnutzer AA, Bertolini G, Bockisch CJ, Straumann D, Marti S. PLoS One 8: e78079, 2013). Hypothetically, PV in any roll position could be biased toward the previous roll position. We asked whether such a "global" bias occurs or whether the bias is "local". The SVV of healthy human subjects (N = 9) was measured in nine roll positions (-120° to +120°, steps = 30°) after 5 min of roll-tilt in one of two adaptation positions (±90°) and compared with control trials without adaptation. After adapting, adjustments were shifted significantly (P < 0.05) toward the previous adaptation position for nearby roll-tilted positions (±30°, ±60°) and upright only. We computationally simulated errors based on the sum of a monotonically increasing function (producing roll undercompensation) and a mixture of Gaussian functions (representing roll overcompensation centered around PV). In combination, the pattern of A- and E-effects could be generated. By shifting the function representing local overcompensation toward the adaptation position, the experimental postadaptation data could be fitted successfully. We conclude that prolonged roll-tilt locally distorts PV rather than globally shifting it. Short-term adaptation of roll overcompensation may explain these shifts and could reflect the brain's strategy to optimize SVV estimates around recent roll positions. Thus postural stability can be improved by visually-mediated compensatory responses at any sustained body-roll orientation. Copyright © 2014 the American Physiological Society.

Optimized Gen-II FeCrAl cladding production in large quantity for campaign testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, Yukinori; Sun, Zhiqian; Pint, Bruce A.

2016-06-03

There are two major objectives in this report; (1) to optimize microstructure control of ATF FeCrAl alloys during tube drawing processes, and (2) to provide an update on the progress of ATF FeCrAl tube production via commercial manufacturers. Experimental efforts have been made to optimize the process parameters balancing the tube fabricability, especially for tube drawing processes, and microstructure control of the final tube products. Lab-scale sheet materials of Gen II FeCrAl alloys (Mo-containing and Nb-containing FeCrAl alloys) were used in the study, combined with a stepwise warm-rolling process and intermediate annealing, aiming to simulate the tube drawing process inmore » a commercial tube manufacturer. The intermediate annealing at 650ºC for 1h was suggested for the tube-drawing process of Mo-containing FeCrAl alloys because it successfully softened the material by recovering the work hardening introduced through the rolling step, without inducing grain coarsening due to recrystallization. The final tube product is expected to have stabilized deformed microstructure providing the improved tensile properties with sufficient ductility. Optimization efforts on Nb-containing FeCrAl alloys focused on the effect of alloying additions and annealing conditions on the stability of deformed microstructure. Relationships between the second-phase precipitates (Fe 2Nb-Laves phase) and microstructure stability are discussed. FeCrAl tube production through commercial tube manufacturers is currently in progress. Three different manufacturers, Century Tubes, Inc. (CTI), Rhenium Alloys, Inc. (RAI), and Superior Tube Company, Inc. (STC), are providing capabilities for cold-drawing, warm-drawing, and HPTR cold-pilgering, respectively. The first two companies are currently working on large quantity tube production (expected 250 ft length) of Gen I model FeCrAl alloy (B136Y3, at CTI) and Gen II (C35M4, at RAI), with the process parameters obtained from the experimental efforts. The expected delivery dates are at the end of July, 2016, and the middle of June, 2016, respectively. Tube production at STC would be the first attempt to apply cold-pilgering to the FeCrAl alloys. Communication has been initiated, and the materials have been machined for the cold-pilgering process.« less

A Phenomenological Study of Perceptions of Early Childhood Administrators Related to Transformational Leadership, Educational Paths, and Organizational Climate

ERIC Educational Resources Information Center

Hayes, Lori

2012-01-01

Early childhood (EC) administrators could be the most important contributors to quality experiences in EC settings; they are also responsible for the caliber of experiences for children and staff. A quality EC program is licensed and accredited with administrators who have professional preparation and work experience and can lead and manage EC…

Development of a Deterred Propellant for a Large Caliber Weapon System

DTIC Science & Technology

1982-06-02

with higher Toy’s than D)BP will require higher concentrations to achieve the sawm burning rate mi.ification. Camphor at the 13 percent "concentration...has about the same "’cv as DIP at 7.5 percent. Thus, for the same burn rate change, camphor would need about twice the concentration, as PBP at the

Metastable Intermolecular Composites (MIC) Primers for Small Caliber Cartridges and Cartridge Actuated Devices

DTIC Science & Technology

2009-07-01

24 iii ACRONYMS AND ABBREVIATIONS ATF Armaments Technology Facility ATK Alliant Techsystems, Inc. ARDEC Armament Research...Technology Facility ( ATF ) firings there, and was instrumental in producing the primers and loading the cartridges needed for the supplemental...and CADs known as the percussion primer. The novel properties associated with nanostructure materials have resulted in the development of thermite

Why Can't We Have It All? The Conflict between the Principalship and Motherhood

ERIC Educational Resources Information Center

Jordan, Jacqueline S.

2012-01-01

Being a principal in today's high-stakes environment is a highly demanding job. Much has been written about the stress principals now face in responding to the increased demands and pressures associated with the role. Districts nationwide continue go to great lengths to find administrators of the highest caliber capable of meeting these…

Medium Caliber Lead-Free Electric Primer. Version 2

DTIC Science & Technology

2012-09-01

Toxic Substance Control Act TGA Thermogravimetric Analysis TNR Trinitroresorcinol V Voltage VDC Voltage Direct Current WSESRB Weapons System...variety of techniques including Thermogravimetric Analysis (TGA), base-hydrolysis, Surface Area Analysis using Brunauer, Emmett, Teller (BET...Distribution From Thermogravimetric Analysis Johnson, C. E.; Fallis, S.; Chafin, A. P.; Groshens, T. J.; Higa, K. T.; Ismail, I. M. K. and Hawkins, T. W

Embracing Your Eureka Moments: Perspectives on Fostering Impactful and Innovative Teaching Styles

ERIC Educational Resources Information Center

Platt, Kristen M.; Welleford, Andrew; Naze, Garrett; Hatcher, April Richardson

2017-01-01

A core question for educators at any stage of their career is often, "How do I improve my own teaching style, and how can I be the educator of the caliber I aspire to be?" In this series of reflective essays, the authors will offer strategies for developing an innovative and individual style that embraces core educational values.…

Environmental Acceptable Medium Caliber Ammunition Percussion Primers

DTIC Science & Technology

2008-05-01

the nanoparticles extremely hydrophobic. The alternative treatment of the solution was the addition of ammonium dihydrogen phosphate (ADP) to serve as...Ultrafine Aluminum Nanoparticles," LA-UR-04-2921. 49 ACRONYM LIST ADP Ammonium Dihydrogen Phosphate Al Aluminum ARDEC Armament Research Development and...Nitrocellulose Nd:Yag Neodymium -doped yttrium aluminum garnet NSWC-IH Naval Surface Warfare Center- Indian Head PAD Propellant actuated device PETN

Race, Power, and Equity in a Multiethnic Urban Elementary School with a Dual-Language "Strand" Program

ERIC Educational Resources Information Center

Palmer, Deborah

2010-01-01

Dual-language education is often lauded for providing high-caliber bilingual instruction in an integrated classroom. This is complicated, however, when a dual-language program does not include all members of a school community. This article examines a "strand" dual-language program that attracts middle-class white students to a predominantly black…

An investigation of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack. M.S. Thesis

NASA Technical Reports Server (NTRS)

Gittner, Nathan M.

1992-01-01

An experimental investigation of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was investigated. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were investigated and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Effect of reducing and replacing pork fat on the physicochemical, instrumental and sensory characteristics throughout storage time of small caliber non-acid fermented sausages with reduced sodium content.

PubMed

Mora-Gallego, Héctor; Serra, Xavier; Guàrdia, Maria Dolors; Arnau, Jacint

2014-05-01

The effect of pork fat reduction (from 44% to 20% final fat content) and its partial substitution by sunflower oil (3% addition) on the physicochemical, instrumental and sensory properties throughout storage time of small caliber non-acid fermented sausages (fuet type) with reduced sodium content (with partial substitution of NaCl by KCl and K-lactate) and without direct addition of nitrate and nitrite (natural nitrate source used instead) was studied. Results showed that sausages with reduced fat (10% initial fat content) and with acceptable sensory characteristics can be obtained by adding to the shoulder lean (8% fat content) during the grinding, either 3.3% backfat (3% fat content) or 3% sunflower oil, both previously finely comminuted with lean. Furthermore, sunflower oil showed to be suitable for partial pork backfat substitution in very lean fermented sausages, conferring desirable sensory properties similar to those of sausages with standard fat content. The sensory quality of the sausages was maintained after three-month cold storage in modified atmosphere. Copyright © 2014 Elsevier Ltd. All rights reserved.

Capillary Versus Aspiration Biopsy: Effect of Needle Size and Length on the Cytopathological Specimen Quality

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopper, Kenneth D.; Grenko, Ronald T.; Fisher, Alicia I.

1996-09-15

Purpose: To test the value of the nonaspiration, or capillary, biopsy technique by experimental comparison with the conventional fine-needle aspiration technique using various needle gauges and lengths. Methods: On fresh hepatic and renal tissue from five autopsies, multiple biopsy specimens were taken with 20, 22, and 23-gauge Chiba needles of 5, 10, 15, and 20-cm length, using the aspiration technique and the capillary technique. The resultant specimens were graded on the basis of a grading scheme by a cytopathologist who was blinded to the biopsy technique. Results: The capillary technique obtained less background blood or clot which could obscure diagnosticmore » tissue, although not significantly different from the aspiration technique (p= 0.2). However, for the amount of cellular material obtained, retention of appropriate architecture, and mean score, the capillary technique performed statistically worse than aspiration biopsy (p < 0.01). In addition, with decreasing needle caliber (increasing needle gauge) and increasing length, the capillary biopsy was inferior to the aspiration biopsy. Conclusion: The capillary biopsy technique is inferior to the aspiration technique according to our study. When the capillary technique is to be applied, preference should be given to larger caliber, shorter needles.« less

Atypical use of PICC in infants and small children: a unicentric experience.

PubMed

Bernasconi, Filippo; Zanaboni, Clelia; Dato, Andrea; Dolcino, Andrea; Bevilacqua, Michela; Montagnini, Luigi; Disma, Nicola

2017-11-17

The peripherally inserted central catheters (PICCs) are vascular access devices (VAD) that are increasingly being used in the pediatric population. If a small vein caliber prevents positioning the catheter in the arm, the following step is to position the same catheter in the supraclavicular area, which can be defined as an off-label use or "atypical" approach, first described by Pittiruti. We retrospectively reviewed PICC positioning with puncture-site in the supra-clavicular area ("atypical" PICC insertion) and then tunneled on the chest. Nineteen atypical PICCs were positioned in 18 patients. The median age of patients at the day of implant was 14 months (IQR 3-27 months), and weight 7.5 kg (IQR 4-12 kg). Within this population, 74% of cases scheduled for a typical PICC insertion presented vein caliber too small for this procedure. For this reason, the typical PICC insertion was changed in favor of an atypical PICC procedure. Atypical PICCs were successfully used in 100% of cases without immediate complications. Atypical PICC positioning is a safe and useful alternative to the conventional technique when there is need for a central vascular access device (CVAD) for mid- or long-term therapy.

Radiation Power as Function of Current in Wall-stabilized AC Arc of Water-cooled Vortex Type with Small Caliber

NASA Astrophysics Data System (ADS)

Iwao, Toru; Naito, Yuto; Shimizu, Yuta; Yamamoto, Shinji

2016-10-01

The problem of an emergency large-scale lighting with the high-intensity discharge (HID) lamp is the lack of radiation intensity because of inappropriate energy balance. Some researchers have researched that the radiation power depended on the arc temperature increases with increasing the current. However, the heat loss and the erosion of the electrode as well as the radiation power increases with increasing the current excessively. AC current replaces alternately the cathode and the anode. Thus, it is possible to avoid the concentration of the heat transfer to the anode. Moreover, the lamp efficiency decreases with increasing the current excessively because of ultra violet rays increment. It is necessary to control the temperature distribution with controlling the current and radius. In this paper, the radiation power as a function of the current in the wall-stabilized AC arc of water-cooled vortex type with small caliber was measured. As a result, the radiation power increased with increasing the current and appropriate wall radius. The radiation of AC arc is smaller than it of DC arc. And, the erosion of electrode decreases.

On the impact of forced roll convection on vertical turbulent transport in cold air outbreaks

NASA Astrophysics Data System (ADS)

Gryschka, Micha; Fricke, Jens; Raasch, Siegfried

2014-11-01

We investigated the impact of roll convection on the convective boundary layer and vertical transports in different cold air outbreak (CAO) scenarios using large eddy simulations (LES). The organization of convection into rolls was triggered by upstream heterogeneities in the surface temperature, representing ice and water. By changing the sea ice distribution in our LES, we were able to simulate a roll and a nonroll case for each scenario. Furthermore, the roll wavelength was varied by changing the scale of the heterogeneity. The characteristics of the simulated rolls and cloud streets, such as aspect ratios, orientation of the roll axes, and downstream extensions of single rolls agreed closely with observations in CAO situations. The vertical turbulent fluxes, calculated for each simulation, were decomposed into contributions from rolls and from unorganized turbulence. Even though our results confirmed that rolls triggered by upstream heterogeneities can substantially contribute to vertical turbulent fluxes, the total fluxes were not affected by the rolls.

Coupled thermal-fluid-mechanics analysis of twin roll casting of A7075 aluminum alloy

NASA Astrophysics Data System (ADS)

Lee, Yun-Soo; Kim, Hyoung-Wook; Cho, Jae-Hyung; Chun, Se-Hwan

2017-09-01

Better understanding of temperature distribution and roll separation force during twin roll casting of aluminum alloys is critical to successfully fabricate good quality of aluminum strips. Therefore, the simulation techniques are widely applied to understand the twin roll casting process in a comprehensive way and to reduce the experimental time and cost of trial and error. However, most of the conventional approaches are considered thermally coupled flow, or thermally coupled mechanical behaviors. In this study, a fully coupled thermal-fluid-mechanical analysis of twin roll casting of A7075 aluminum strips was carried out using the finite element method. Temperature profile, liquid fraction and metal flow of aluminum strips with different thickness were predicted. Roll separation force and roll temperatures were experimentally obtained from a pilot-scale twin roll caster, and those results were compared with model predictions. Coupling the fluid of the liquid melt to the thermal and mechanical modeling reasonably predicted roll temperature distribution and roll separation force during twin roll casting.

75 FR 75455 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full Sunset Review of Countervailing... of the countervailing duty (CVD) order on certain hot-rolled flat-rolled carbon-quality steel products (hot-rolled steel) from Brazil, pursuant to section 751(c) of the Tariff Act of 1930, as amended...

21 CFR 136.180 - Whole wheat bread, rolls, and buns.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Whole wheat bread, rolls, and buns. 136.180... § 136.180 Whole wheat bread, rolls, and buns. (a) Each of the foods whole wheat bread, graham bread, entire wheat bread, whole wheat rolls, graham rolls, entire wheat rolls, whole wheat buns, graham buns...

Texture and mechanical properties of Al-0.5Mg-1.0Si-0.5Cu alloy sheets manufactured via a cross rolling method

NASA Astrophysics Data System (ADS)

Jeon, Jae-Yeol; Son, Hyeon-Taek; Woo, Kee-Do; Lee, Kwang-Jin

2012-04-01

The relationship between the texture and mechanical properties of 6xxx aluminum alloy sheets processed via cross rolling was investigated. The microstructures of the conventional rolled and cross rolled sheets after annealing were analyzed using optical micrographs (OM). The texture distribution across the thickness in the Al-Mg-Si-Cu alloy, conventional rolled sheets, and cross rolled sheets both before and after annealing was investigated via X-ray texture measurements. The texture was analyzed in three layers from the surface to the center of the sheet. The β-fiber texture of the conventional rolled sheet was typical of the texture obtained using aluminumoll ring. After annealing, the typical β-fiber orientations were changed to recrystallization textures: cube{001}<100> and normal direction (ND)-rotated cubes. However, the texture of the cross rolled sheet was composed of an asymmetrical, rolling direction (RD)-rotated cubes. After annealing, the asymmetrical orientations in the cross rolled sheet were changed to a randomized texture. The average R-value of the annealed cross rolled sheets was higher than that of the conventional rolled sheets. The limit dome height (LDH) test results demonstrated that cross rolling is effective in improving the formability of the Al-Mg-Si-Cu alloy sheets.

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions... the rolling with emulsions subcategory. ...

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions... the rolling with emulsions subcategory. ...

CLASSICAL AREAS OF PHENOMENOLOGY: Lattice Boltzmann simulation of behaviour of particles moving in blood vessels under the rolling massage

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Yang, Xiao-Feng; Wang, Cai-Feng; Li, Hua-Bing

2009-07-01

The rolling massage is one of the most important manipulations in Chinese massage, which is expected to eliminate many diseases. Here, the effect of the rolling massage on a pair of particles moving in blood vessels under rolling massage manipulation is studied by the lattice Boltzmann simulation. The simulated results show that the motion of each particle is considerably modified by the rolling massage, and it depends on the relative rolling velocity, the rolling depth, and the distance between particle position and rolling position. Both particles' translational average velocities increase almost linearly as the rolling velocity increases, and obey the same law. The increment of the average relative angular velocity for the leading particle is smaller than that of the trailing one. The result is helpful for understanding the mechanism of the massage and to further develop the rolling techniques.

Rolling into spatial disorientation: simulator demonstration of the post-roll (Gillingham) illusion.

PubMed

Nooij, Suzanne A E; Groen, Eric L

2011-05-01

Spatial disorientation (SD) is still a contributing factor in many aviation accidents, stressing the need for adequate SD training scenarios. In this article we focused on the post-roll effect (the sensation of rolling back after a roll maneuver, such as an entry of a coordinated turn) and investigated the effect of roll stimuli on the pilot's ability to stabilize their roll attitude. This resulted in a ground-based demonstration scenario for pilots. The experiments took place in the advanced 6-DOF Desdemona motion simulator, with the subject in a supine position. Roll motions were either fully automated with the subjects blindfolded (BLIND), automated with the subject viewing the cockpit interior (COCKPIT), or self-controlled (LEAD). After the roll stimulus subjects had to cancel all perceived simulator motion without any visual feedback. Both the roll velocity and duration were varied. In 68% of all trials subjects corrected for the perceived motion of rolling back by initiating a roll motion in the same direction as the preceeding roll. The effect was dependent on both rate and duration, in a manner consistent with semicircular canal dynamics. The effect was smallest in the BLIND scenario, but differences between simulation scenarios were non-significant. The results show that the effects of the post-roll illusion on aircraft control can be demonstrated adequately in a flight simulator using an attitude control task. The effect is present even after short roll movements, occurring frequently in flight. Therefore this demonstration is relevant for spatial disorientation training programs for pilots.

Defect Analysis of Roll-to-Roll SAIL Manufactured Flexible Display Backplanes

DTIC Science & Technology

2011-01-01

tenting defect through the SAIL process Figure 5: Flexible backplane electrical tester Figure 6: R2R optical inspection system Figure 7: TEM of TFT ...Analysis of Roll-to-Roll SAIL Manufactured Flexible Display...Marcia Almanza-Workman, Robert A. Garcia, HanJun Kim, Ohseung Kwon, Frank Jeffrey HP Laboratories HPL-2011-35 SAIL, flexible displays, roll-to-roll HP

Wind-tunnel investigation at supersonic speeds of a remote-controlled canard missile with a free-rolling-tail brake torque system

NASA Technical Reports Server (NTRS)

Blair, A. B., Jr.

1985-01-01

Wind tunnel tests were conducted at Mach numbers 1.70, 2.16, and 2.86 to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed or free rolling tailfin afterbodies. Mechanical coupling effects of the free-rolling-tail afterbody were investigated by using an electronic electromagnetic brake system providing arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail roll rate. Remote-controlled canards were deflected to provide pitch, yaw, and roll control. Results indicate that the induced rolling moment coefficients due to canard yaw control are reduced and linearized for the free-rolling-tail (free-tail) configuration. The canards of the latter provide conventional roll control for the entire angle-of-attack test range. For the free-tail configuration, the induced rolling moment coefficient due to canard yaw control increased and the canard roll control decreased with increases in brake torque, which simulated bearing friction torque. It appears that a compromise in regard to bearing friction, for example, low-cost bearings with some friction, may allow satisfactory free-tail aerodynamic characteristics that include reductions in adverse rolling-moment coefficients and lower tail roll rates.

Open ended tubing cutters

NASA Technical Reports Server (NTRS)

Girala, A. S. (Inventor)

1981-01-01

A self clamping cutting tool which includes a handle attached to a C-shaped housing is described. Rotatably mounted within the housing is a C-shaped tool body carrying a set of clamping rolls, two support rolls, and an edged cutting roll (64). The support rolls are disposed to one side of the axis of a pipe and the cutting roll is disposed to the other side of a pipe axis so that these rolls contact a pipe at three circumferential points. Cutter advancing apparatus advance the cutting roll toward the support rollers. The support rolls and cutting roll are rotatable independently of the C-shaped housing. A one way ratchet mechanism disposed between the C-shaped housing and the C-shaped tool body permits operation by movement in one rotational direction about the pipe axis.

Evaluation of roll designs on a roll-crusher/ crusher/splitter biomass harvester: test bench results

Treesearch

Colin Ashmore; Donald L. Sirois; Bryce J. Stokes

1987-01-01

Four different roll designs were evaluated on a test bench roll crusher/splitter to determine feeding and crushing efficiencies. For each design, different gap settings for the primary and secondary rolls were tested at two hydraulic cylinder pressures on the primary crush roll to determine their ability to crush and/or feed tree bolts. Seven different diameter classes...

Distinct molecular and cellular contributions to stabilizing selectin-mediated rolling under flow

PubMed Central

Yago, Tadayuki; Leppänen, Anne; Qiu, Haiying; Marcus, Warren D.; Nollert, Matthias U.; Zhu, Cheng; Cummings, Richard D.; McEver, Rodger P.

2002-01-01

Leukocytes roll on selectins at nearly constant velocities over a wide range of wall shear stresses. Ligand-coupled microspheres roll faster on selectins and detach quickly as wall shear stress is increased. To examine whether the superior performance of leukocytes reflects molecular features of native ligands or cellular properties that favor selectin-mediated rolling, we coupled structurally defined selectin ligands to microspheres or K562 cells and compared their rolling on P-selectin. Microspheres bearing soluble P-selectin glycoprotein ligand (sPSGL)-1 or 2-glycosulfopeptide (GSP)-6, a GSP modeled after the NH2-terminal P-selectin–binding region of PSGL-1, rolled equivalently but unstably on P-selectin. K562 cells displaying randomly coupled 2-GSP-6 also rolled unstably. In contrast, K562 cells bearing randomly coupled sPSGL-1 or 2-GSP-6 targeted to a membrane-distal region of the presumed glycocalyx rolled more like leukocytes: rolling steps were more uniform and shear resistant, and rolling velocities tended to plateau as wall shear stress was increased. K562 cells treated with paraformaldehyde or methyl-β-cyclodextrin before ligand coupling were less deformable and rolled unstably like microspheres. Cells treated with cytochalasin D were more deformable, further resisted detachment, and rolled slowly despite increases in wall shear stress. Thus, stable, shear-resistant rolling requires cellular properties that optimize selectin–ligand interactions. PMID:12177042

Hot rolling of thick uranium molybdenum alloys

DOEpatents

DeMint, Amy L.; Gooch, Jack G.

2015-11-17

Disclosed herein are processes for hot rolling billets of uranium that have been alloyed with about ten weight percent molybdenum to produce cold-rollable sheets that are about one hundred mils thick. In certain embodiments, the billets have a thickness of about 7/8 inch or greater. Disclosed processes typically involve a rolling schedule that includes a light rolling pass and at least one medium rolling pass. Processes may also include reheating the rolling stock and using one or more heavy rolling passes, and may include an annealing step.

CROSS-DISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Effect of Rolling Massage on Particle Moving Behaviour in Blood Vessels

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Fan, Li-Juan; Yang, Xiao-Feng; Chen, Yan-Yan

2008-09-01

The rolling massage manipulation is a classic Chinese massage, which is expected to eliminate many diseases. Here the effect of the rolling massage on the particle moving property in the blood vessels under the rolling massage manipulation is studied by the lattice Boltzmann simulation. The simulation results show that the particle moving behaviour depends on the rolling velocity, the distance between particle position and rolling position. The average values, including particle translational velocity and angular velocity, increase as the rolling velocity increases almost linearly. The result is helpful to understand the mechanism of the massage and develop the rolling techniques.

Computational Analysis of Ares I Roll Control System Jet Interaction Effects on Rolling Moment

NASA Technical Reports Server (NTRS)

Deere, Karen A.; Pao, S. Paul; Abdol-Hamid, Khaled S.

2011-01-01

The computational flow solver USM3D was used to investigate the jet interaction effects from the roll control system on the rolling moment of the Ares I full protuberance configuration at wind tunnel Reynolds numbers. Solutions were computed at freestream Mach numbers from M = 0.5 to M = 5 at the angle of attack 0deg, at the angle of attack 3.5deg for a roll angle of 120deg, and at the angle of attack 7deg for roll angles of 120deg and 210deg. Results indicate that the RoCS housing provided a beneficial jet interaction effect on vehicle rolling moment for M > or = 0.9. Most of the components downstream of the roll control system housing contributed to jet interaction penalties on vehicle rolling moment.

Small-Molecule Organic Photovoltaic Modules Fabricated via Halogen-Free Solvent System with Roll-to-Roll Compatible Scalable Printing Method.

PubMed

Heo, Youn-Jung; Jung, Yen-Sook; Hwang, Kyeongil; Kim, Jueng-Eun; Yeo, Jun-Seok; Lee, Sehyun; Jeon, Ye-Jin; Lee, Donmin; Kim, Dong-Yu

2017-11-15

For the first time, the photovoltaic modules composed of small molecule were successfully fabricated by using roll-to-roll compatible printing techniques. In this study, blend films of small molecules, BTR and PC 71 BM were slot-die coated using a halogen-free solvent system. As a result, high efficiencies of 7.46% and 6.56% were achieved from time-consuming solvent vapor annealing (SVA) treatment and roll-to-roll compatible solvent additive approaches, respectively. After successful verification of our roll-to-roll compatible method on small-area devices, we further fabricated large-area photovoltaic modules with a total active area of 10 cm 2 , achieving a power conversion efficiency (PCE) of 4.83%. This demonstration of large-area photovoltaic modules through roll-to-roll compatible printing methods, even based on a halogen-free solvent, suggests the great potential for the industrial-scale production of organic solar cells (OSCs).

Rolling Process Modeling Report: Finite-Element Prediction of Roll Separating Force and Rolling Defects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Lavender, Curt A.; Paxton, Dean M.

2014-04-23

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum (U-10Mo) alloy plate-type fuel for the U.S. high-performance research reactors. This work supports the Convert Program of the U.S. Department of Energy’s National Nuclear Security Administration (DOE/NNSA) Global Threat Reduction Initiative. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll separating forces and rolling defects. Simulations were performed using a finite-element model developed using the commercial code LS-Dyna. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel have been conducted following two different schedules. Model predictions ofmore » the roll-separation force and roll-pack thicknesses at different stages of the rolling process were compared with experimental measurements. This report discusses various attributes of the rolled coupons revealed by the model (e.g., dog-boning and thickness non-uniformity).« less

Fault Diagnosis for Centre Wear Fault of Roll Grinder Based on a Resonance Demodulation Scheme

NASA Astrophysics Data System (ADS)

Wang, Liming; Shao, Yimin; Yin, Lei; Yuan, Yilin; Liu, Jing

2017-05-01

Roll grinder is one of the important parts in the rolling machinery, and the grinding precision of roll surface has direct influence on the surface quality of steel strip. However, during the grinding process, the centre bears the gravity of the roll and alternating stress. Therefore, wear or spalling faults are easily observed on the centre, which will lead to an anomalous vibration of the roll grinder. In this study, a resonance demodulation scheme is proposed to detect the centre wear fault of roll grinder. Firstly, fast kurtogram method is employed to help select the sub-band filter parameters for optimal resonance demodulation. Further, the envelope spectrum are derived based on the filtered signal. Finally, two health indicators are designed to conduct the fault diagnosis for centre wear fault. The proposed scheme is assessed by analysing experimental data from a roll grinder of twenty-high rolling mill. The results show that the proposed scheme can effectively detect the centre wear fault of the roll grinder.

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas

The effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.percent Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 degrees C for 48 hours and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot- + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot- + cold-rolled to 0.2 mm + annealed at 700 deg. C for 1 hour, and (iii) hot- + cold-rolled to 0.2 mm + annealed at 1000 deg. C for 60 hours. U10Momore » rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries.« less

Manufacturing Methods and Technology (MMT) Program for FY 80, Large Caliber Weapons System Laboratory, ARRADCOM

DTIC Science & Technology

1980-09-01

ABIA .S-POUcOT «♦165 PROTOTYFEFACILITYFORRECOVERYGFHMXFRROX/HNXAONIX HRICCI »II ESPO 216C ESPO *7-0EC4* 19AUG70 2.151 1.422...TOTAL -^ .670 TCCH ABiA - IS-«PROP»äXP- »18 9 HIGHFKA GST EELPRODUCTION PROCESS WStMftf* 37»2 HSO FY79 .»CO .60» 0.000 0.000

Defense Acquisition Workforce Modernization

DTIC Science & Technology

2010-07-01

34 IV. ’’Smart Buyers ” for Twenty-First Century Requirements...first century should be one that centers on the concept of the “smart buyer .” The “smart buyer ” is one who is value focused, and has the requisite... buyer ” model, DoD must overcome several challenges. First, due to low pay, DoD will likely encounter difficulties in trying to retain high-caliber

Primary cutaneous vascular leiomyosarcoma: a rare subtype of leiomyosarcoma of the skin.

PubMed

Ortins-Pina, Ana; Soares-de-Almeida, Luís; Rütten, Arno

2018-05-08

Primary smooth muscle malignancies in the skin account for approximately 2-3% of all soft tissue sarcomas 1,2 . We read with interest a recent JCP report on a vascular leiomyosarcoma arising from vena saphena magna 3 . We report herein a case of primary cutaneous vascular leiomyosarcoma arising from a small-caliber dermal vein. This article is protected by copyright. All rights reserved.

Who Cares? Child Care Teachers and the Quality of Care in America. Final Report, National Child Care Staffing Study.

ERIC Educational Resources Information Center

Whitebook, Marcy; And Others

The National Child Care Staffing Study (NCCSS) was designed to explore how child care teaching staff and their working conditions affect the caliber of center-based child care. Four major policy questions were addressed: (1) Who teaches in America's child care centers? (2) What do they contribute to the quality of care provided? (3) Do centers…

Investigation of Chemically Vapor Deposited Tantalum for Medium Caliber Gun Barrel Protection

DTIC Science & Technology

2008-10-01

electrodeposition ) by December 31, 2006. As a result of this ordinance, several efforts were initiated to investigate the use of environmentally...catalyzed reactions (i.e., heterogeneous as compared to homogeneous where the reactions nucleate in the gas phase). The occurrence of a chemical reaction...Precursor Desorption of Volatile Surface Reaction Products Adsorption of Film Precursor Nucleation and Growth Transport Transport Figure 2. Schematic

Securing the Northern Maritime Border Through Maritime Domain Awareness

DTIC Science & Technology

2010-09-01

is handled through 1) aircraft overflights (Coast Guard and Coast Guard Auxiliary aircraft, U.S. Air Force, Customs and Border Patrol, Canadian...caliber machine gun, or like automatic weapons. Bruce Levy, Director, U.S. Transboundary Division conveyed to Nancy Mason, Director, Office of...1 NORAD, the North American Aerospace Defense Command, is a binational military command focused on the air defense of North America and located

Acquiring Technical Data With Renewable Real Options

DTIC Science & Technology

2016-04-30

Development, and Engineering Center, 2009). Faced with diminishing sources for M2 .50 caliber machine gun parts , an Army engineering center entered the...data needed for life cycle sustainment functions such as maintenance or competitive spare parts procurement, but this expectation is more complicated...than it seems (DoD, 2015). The needs and timing for competitive spare parts procurement are uncertain, and changes in system configuration or

A Photoelastic Study of Load Distributions and Stresses in Multi-Groove Connections of the Same Material under Tension.

DTIC Science & Technology

1982-05-01

CALIBER WEAPON SYSTEMS LABORATORY BENleT WEAPONS LABORATORY WATERVLIET, N. Y. 12189 ANCMS No. 61110191A0011 DA Project No. 1L161101AS& PRON No...Benet Weapons Laboratory, DRDAR-LCB-TL DA Project No. lL16110IA9A Watervliet, NY 12189 PRON No. 1A2231491AIA I. CONTROLLING OFFICE NAME AND ADDRESS 12

Fundamental Aerodynamic Investigations for Development of Arrow-Stabilized Projectiles

NASA Technical Reports Server (NTRS)

Kurzweg, Hermann

1947-01-01

The numerous patent applications on arrow-stabilized projectiles indicate that the idea of projectiles without spin is not new, but has appeared in various proposals throughout the last decades. As far as projectiles for subsonic speeds are concerned, suitable shapes have been developed for sometime, for example, numerous grenades. Most of the patent applications, though, are not practicable particularly for projectiles with supersonic speed. This is because the inventor usually does not have any knowledge of aerodynamic flow around the projectile nor any particular understanding of the practical solution. The lack of wind tunnels for the development of projectiles made it necessary to use firing tests for development. These are obviously extremely tedious or expensive and lead almost always to failures. The often expressed opinion that arrow-stabilized projectiles cannot fly supersonically can be traced to this condition. That this is not the case has been shown for the first time by Roechling on long projectiles with foldable fins. Since no aerodynamic investigations were made for the development of these projectiles, only tedious series of firing tests with systematic variation of the fins could lead to satisfactory results. These particular projectiles though have a disadvantage which lies in the nature cf foldable fins. They occasionally do not open uniformly in flight, thus causing unsymmetry in flow and greater scatter. The junctions of fins and body are very bad aerodynamically and increase the drag. It must be possible to develop high-performance arrow-stabilized projectiles based on the aerodynamic research conducted during the last few years at Peenemuende and new construction ideas. Thus the final shape, ready for operational use, could be developed in the wind tunnel without loss of expensive time in firing tests. The principle of arrow-stabilized performance has been applied to a large number of caliburs which were stabilized by various means Most promising was the development of a subcaliber wing-stabilized projectile with driving disc (Treibspiegel) where rigid control surfaces extend beyond the caliber of the projectile into the free stream. The stabilized projectiles of full-caliber, wing-stabilized projectiles with fins within the caliber is considerably more difficult. A completely satisfactory solution for the latter has not been found yet.

Association of consumption of dairy products and meat with retinal vessel calibers in subjects at increased cardiovascular risk.

PubMed

Karatzi, K; Aissopou, E K; Tsirimiagou, C; Fatmeli, E; Sfikakis, P P; Protogerou, A D

2016-08-01

Association of dairy products and meat consumption with macrocirculation is previously described, but such association with microcirculation is poorly investigated. We aimed to test the hypothesis that the consumption of high- and low-fat dairy products as well as red, white, and processed meat is associated with retinal vessel calibers in adults at an increased risk of cardiovascular disease (CVD). In consecutive subjects (n = 181, age: 51.3 ± 12.4 years, 51.4% women) without CVD and diabetes mellitus but with increased CVD risk, we obtained digital left and right retinal images. These images were assessed with validated software to determine central retinal arteriolar and venular equivalents and the arteriolar to venular ratio (CRAE, CRVE, and AVR, respectively). The consumption of dairy products and meat was assessed through 24-h recalls in all volunteers. After adjustment for potential confounders, the following findings were obtained: (i) low-fat milk and yogurt were positively associated with CRAE (b=0.145, p=0.031 left; b=0.141, p=0.038 right) and inversely associated with CRVE (b=-0.155, p=0.026 left; b=-0.146, p=0.041 right); (ii) low-fat cheese was positively associated with CRAE (b=0.164, p=0.011 left and b=0.155, p=0.017 right); and (iii) red meat was inversely associated with CRAE (b=-0.143, p=0.032 left; b=-0.114, p=0.050 right). High-fat milk, yogurt, and cheese or white and processed meat were not found to be associated with retinal vessel calibers. High consumption of low-fat milk, yogurt, and cheese and low consumption of red meat could be beneficial for retinal microvascular health. Prospective studies are needed to verify these findings. Copyright © 2016 The Italian Society of Diabetology, the Italian Society for the Study of Atherosclerosis, the Italian Society of Human Nutrition, and the Department of Clinical Medicine and Surgery, Federico II University. Published by Elsevier B.V. All rights reserved.

Neutrophil Counts and Initial Presentation of 12 Cardiovascular Diseases: A CALIBER Cohort Study.

PubMed

Shah, Anoop Dinesh; Denaxas, Spiros; Nicholas, Owen; Hingorani, Aroon D; Hemingway, Harry

2017-03-07

Neutrophil counts are a ubiquitous measure of inflammation, but previous studies on their association with cardiovascular disease (CVD) were limited by small numbers of patients or a narrow range of endpoints. This study investigated associations of clinically recorded neutrophil counts with initial presentation for a range of CVDs. We used linked primary care, hospitalization, disease registry, and mortality data in England. We included people 30 years or older with complete blood counts performed in usual clinical care and no history of CVD. We used Cox models to estimate cause-specific hazard ratios (HRs) for 12 CVDs, adjusted for cardiovascular risk factors and acute conditions affecting neutrophil counts (such as infections and cancer). Among 775,231 individuals in the cohort, 154,179 had complete blood counts performed under acute conditions and 621,052 when they were stable. Over a median 3.8 years of follow-up, 55,004 individuals developed CVD. Adjusted HRs comparing neutrophil counts 6 to 7 versus 2 to 3 × 10 9 /l (both within the 'normal' range) showed strong associations with heart failure (HR: 2.04; 95% confidence interval [CI]: 1.82 to 2.29), peripheral arterial disease (HR: 1.95; 95% CI: 1.72 to 2.21), unheralded coronary death (HR: 1.78; 95% CI: 1.51 to 2.10), abdominal aortic aneurysm (HR: 1.72; 95% CI: 1.34 to 2.21), and nonfatal myocardial infarction (HR: 1.58; 95% CI: 1.42 to 1.76). These associations were linear, with greater risk even among individuals with neutrophil counts of 3 to 4 versus 2 to 3 × 10 9 /l. There was a weak association with ischemic stroke (HR: 1.36; 95% CI: 1.17 to 1.57), but no association with stable angina or intracerebral hemorrhage. Neutrophil counts were strongly associated with the incidence of some CVDs, but not others, even within the normal range, consistent with underlying disease mechanisms differing across CVDs. (White Blood Cell Counts and Onset of Cardiovascular Diseases: a CALIBER Study [CALIBER]; NCT02014610). Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Postoperative enlargement and prognostic effects of portal venous bypass grafts in children undergoing Rex shunt.

PubMed

Zhang, Jin-Shan; Li, Long; Cheng, Wei

2018-05-22

Patency of the bypass vein after a Rex shunt is an important indicator of prognosis. However, there is no report about the change of caliber of the bypass vein after a Rex shunt. The aim of this study was to identify postoperative changes of the bypass vein and to assess the relationship with prognosis. Between October 2008 and October 2016 in our center, 114 children were diagnosed with extrahepatic portal venous obstruction. The portal cavernoma-portal bypass with interposition of grafted portal vessels was performed in 31 children, the gastroportal shunt was performed in 54 children, and other Rex shunts were performed in another 29 children. At follow-up, the patency and diameter of the bypass vein were assessed with ultrasound and computed tomography. The intraoperative and postoperative diameters of the bypass vein were compared to identify postoperative changes of the bypass vein. Prognosis was compared between children with and children without an enlarged bypass vein. The caliber of the bypass vein was enlarged in 50% of children (40/80) at 6 months postoperatively. The postoperative incidences of rebleeding and esophageal varices were significantly lower in children with an enlarged bypass vein than in those without (P < .05). Postoperatively, the reduced splenic size was significantly higher in children with an enlarged bypass vein than in those without (P < .05). The postoperative increase in platelet count in children with an enlarged bypass vein was significantly higher than in those without (P = .006). There was no significant difference in the flow velocity of the bypass vein between children with and children without an enlarged bypass vein (P = .133). The portal pressure was significantly reduced after surgery in children with an enlarged bypass vein than in children without an enlarged bypass vein (P = .017). The caliber of the bypass vein increases in 50% of children after a Rex shunt using a grafted portal vessel, which is related to a better prognosis. Copyright © 2018 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

76 FR 22868 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Countervailing Duty Administrative... administrative review of the countervailing duty order on certain hot-rolled flat-rolled carbon- quality steel...-Quality Steel Products From Brazil: Preliminary Results of Countervailing Duty Administrative Review, 75...

Influence of different kinds of rolling on the crystallographic texture and magnetic induction of a NOG 3 wt% Si steel

NASA Astrophysics Data System (ADS)

Silva, J. M.; Baêta Júnior, E. S.; Moraes, N. R. D. C.; Botelho, R. A.; Felix, R. A. C.; Brandao, L.

2017-01-01

The purpose of this work was to study the influence of different kinds of rolling on the magnetic properties of NOG steel, an electric steel widely used in electrical motors. These properties are highly correlated with the crystallographic texture of the material, which can be changed by rolling. Three kinds of rolling were examined: conventional rolling, cross-rolling and asymmetrical rolling. The crystallographic texture was determined by X-ray diffraction and the magnetic properties were calculated from a theoretical model that related the magnetic induction to crystallographic texture through the anisotropy energy. The results show that cross-rolling yields higher values of magnetic induction than the other processes.

A study of roll attractor and wing rock of delta wings at high angles of attack

NASA Technical Reports Server (NTRS)

Niranjana, T.; Rao, D. M.; Pamadi, Bandu N.

1993-01-01

Wing rock is a high angle of attack dynamic phenomenon of limited cycle motion predominantly in roll. The wing rock is one of the limitations to combat effectiveness of the fighter aircraft. Roll Attractor is the steady state or equilibrium trim angle (phi(sub trim)) attained by the free-to-roll model, held at some angle of attack, and released form rest at a given initial roll (bank) angle (phi(sub O)). Multiple roll attractors are attained at different trim angles depending on initial roll angle. The test facility (Vigyan's low speed wind tunnel) and experimental work is presented here along with mathematical modelling of roll attractor phenomenon and analysis and comparison of predictions with experimental data.

Multiphysical FE-analysis of a front-end bending phenomenon in a hot strip mill

NASA Astrophysics Data System (ADS)

Ilmola, Joonas; Seppälä, Oskari; Leinonen, Olli; Pohjonen, Aarne; Larkiola, Jari; Jokisaari, Juha; Putaansuu, Eero

2018-05-01

In hot steel rolling processes, a slab is generally rolled to a transfer bar in a roughing process and to a strip in a hot strip rolling process. Over several rolling passes the front-end may bend upward or downward due to asymmetrical rolling conditions causing entry problems in the next rolling pass. Many different factors may affect the front-end bending phenomenon and are very challenging to measure. Thus, a customized finite element model is designed and built to simulate the front-end bending phenomenon in a hot strip rolling process. To simulate the functioning of the hot strip mill precisely, automated controlling logic of the mill must be considered. In this paper we studied the effect of roll bite friction conditions and amount of reduction on the front-end bending phenomenon in a hot strip rolling process.

Quantitative analysis and predictive engineering of self-rolling of nanomembranes under anisotropic mismatch strain

NASA Astrophysics Data System (ADS)

Chen, Cheng; Song, Pengfei; Meng, Fanchao; Li, Xiao; Liu, Xinyu; Song, Jun

2017-12-01

The present work presents a quantitative modeling framework for investigating the self-rolling of nanomembranes under different lattice mismatch strain anisotropy. The effect of transverse mismatch strain on the roll-up direction and curvature has been systematically studied employing both analytical modeling and numerical simulations. The bidirectional nature of the self-rolling of nanomembranes and the critical role of transverse strain in affecting the rolling behaviors have been demonstrated. Two fabrication strategies, i.e., third-layer deposition and corner geometry engineering, have been proposed to predictively manipulate the bidirectional rolling competition of strained nanomembranes, so as to achieve controlled, unidirectional roll-up. In particular for the strategy of corner engineering, microfabrication experiments have been performed to showcase its practical application and effectiveness. Our study offers new mechanistic knowledge towards understanding and predictive engineering of self-rolling of nanomembranes with improved roll-up yield.

Preparation of high-strength Al-Mg-Si-Cu-Fe alloy via heat treatment and rolling

NASA Astrophysics Data System (ADS)

Liu, Chong-yu; Yu, Peng-fei; Wang, Xiao-ying; Ma, Ming-zhen; Liu, Ri-ping

2014-07-01

An Al-Mg-Si-Cu-Fe alloy was solid-solution treated at 560°C for 3 h and then cooled by water quenching or furnace cooling. The alloy samples which underwent cooling by these two methods were rolled at different temperatures. The microstructure and mechanical properties of the rolled alloys were investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction analysis, and tensile testing. For the water-quenched alloys, the peak tensile strength and elongation occurred at a rolling temperature of 180°C. For the furnace-cooled alloys, the tensile strength decreased initially, until the rolling temperature of 420°C, and then increased; the elongation increased consistently with increasing rolling temperature. The effects of grain boundary hardening and dislocation hardening on the mechanical properties of these rolled alloys decreased with increases in rolling temperature. The mechanical properties of the 180°C rolling water-quenched alloy were also improved by the presence of β″ phase. Above 420°C, the effect of solid-solution hardening on the mechanical properties of the rolled alloys increased with increases in rolling temperature.

Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface.

PubMed

Gu, Yun-Qing; Fan, Tian-Xing; Mou, Jie-Gang; Yu, Wei-Bo; Zhao, Gang; Wang, Evan

2016-01-01

In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis.

Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface

PubMed Central

Gu, Yun-qing; Fan, Tian-xing; Mou, Jie-gang; Yu, Wei-bo; Zhao, Gang; Wang, Evan

2016-01-01

In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis. PMID:27022235

Search for Planetary-mass Companions of the LHB Star eta Corvi

NASA Astrophysics Data System (ADS)

Marengo, Massimo; Lisse, Carey; Stapelfeldt, Karl; Hulsebus, Alan; Sitko, Michael

2016-08-01

The nearby sun-like star eta Corvi (F2V, d = 18 pc, age = 1.2 Gyr) has long been known to possess a bright, dusty Kuiper belt that has been recently resolved with Herschel/PACS. In addition to this structure, eta Corvi is one of the rare mature planetary systems to possess also an inner warm belt (~ 3 AU radius), located within the Terrestrial Habitable Zone (TLZ) of this star. Our characterization of this structure, based on Spitzer/IRS and NASA/IRTF SpeX spectral observations, reveals the signature of ice, organics and silicate dust in this warm belt. This supports the hypothesis that eta Corvi is undergoing a Late Heavy Bombardment (LHB), delivering life-bearing water- and organic-rich material from the Kuiper belt to the TLZ, at roughly the same age as the Solar System?s LHB. For the past four years we have monitored the brightness of eta Corvi?s warm belt with Spitzer/IRAC, finding that its infrared emission has been stable over a multi-year timescale. In 2012 we have also conducted a search for widely separated substellar-mass companions of this star, whose presence as been suggested as a possible trigger for the LHB currently undergoing in the system. This search has led to the identification of three sources with colors and magnitudes consistent with being late-T and Y dwarf companions of this star. We here propose to acquire a new deep roll-subtracted image of the system, 5 years after our first visit, to test for common proper motion of these candidate companions, and determine if any of this sources is physically associated with eta Corvi. A positive identification of a substellar-mass companions (one of which could be a 3-5 MJ planet at ~360 AU from the star) would be a significant step in understanding the processes leading to LHB-like events in a system analogous to the Solar System.

77 FR 19619 - Notice of Extension of Time Limit for the Preliminary Results of Administrative Review of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-02

... Limit for the Preliminary Results of Administrative Review of the Suspension Agreement on Hot-Rolled... Preliminary Results of Administrative Review of the Suspension Agreement on Hot-Rolled Flat-Rolled Carbon... Suspending the Antidumping Investigation on Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from the...

75 FR 32160 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

... DEPARTMENT OF COMMERCE International Trade Administration [C-351-829] Certain Hot-Rolled Flat... Commerce (the Department) published the countervailing duty order on certain hot-rolled flat- rolled carbon-quality steel products from Brazil. See Agreement Suspending the Countervailing Duty Investigation on Hot...

Why Low Bounce Balls Exhibit High Rolling Resistance

ERIC Educational Resources Information Center

Cross, Rod

2015-01-01

A simple experiment is described to measure the coefficient of rolling friction for a low bounce ball rolling on a horizontal surface. As observed previously by others, the coefficient increased with rolling speed. The energy loss due to rolling friction can be explained in terms of the measured coefficient of restitution for the ball, meaning…

76 FR 15299 - Certain Hot-Rolled Carbon Steel Flat Products From India: Preliminary Rescission of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-21

... DEPARTMENT OF COMMERCE International Trade Administration [C-533-821] Certain Hot-Rolled Carbon... on certain hot-rolled carbon steel flat products from India. See Antidumping or Countervailing Duty... products covered under this order are certain hot-rolled flat- rolled carbon steel flat products of a...

78 FR 42039 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-15

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled...\\ See Notice of Antidumping Duty Order: Certain Hot-Rolled Carbon Steel Flat Products from the People's...

75 FR 27297 - Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Final Results of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-14

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon...'') published the preliminary results of the antidumping duty administrative review for certain hot-rolled carbon steel flat products from India (``Indian Hot-Rolled''). See Certain Hot-Rolled Carbon Steel Flat...

Flexure-based Roll-to-roll Platform: A Practical Solution for Realizing Large-area Microcontact Printing

PubMed Central

Zhou, Xi; Xu, Huihua; Cheng, Jiyi; Zhao, Ni; Chen, Shih-Chi

2015-01-01

A continuous roll-to-roll microcontact printing (MCP) platform promises large-area nanoscale patterning with significantly improved throughput and a great variety of applications, e.g. precision patterning of metals, bio-molecules, colloidal nanocrystals, etc. Compared with nanoimprint lithography, MCP does not require a thermal imprinting step (which limits the speed and material choices), but instead, extreme precision with multi-axis positioning and misalignment correction capabilities for large area adaptation. In this work, we exploit a flexure-based mechanism that enables continuous MCP with 500 nm precision and 0.05 N force control. The fully automated roll-to-roll platform is coupled with a new backfilling MCP chemistry optimized for high-speed patterning of gold and silver. Gratings of 300, 400, 600 nm line-width at various locations on a 4-inch plastic substrate are fabricated at a speed of 60 cm/min. Our work represents the first example of roll-to-roll MCP with high reproducibility, wafer scale production capability at nanometer resolution. The precision roll-to-roll platform can be readily applied to other material systems. PMID:26037147

Lattice Boltzmann Simulation of Blood Flow in Blood Vessels with the Rolling Massage

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Xu, Shi-Xiong; Qian, Yue-Hong; Fang, Hai-Ping

2005-12-01

The rolling massage manipulation is a classic Chinese massage, which is expected to improve the circulation by pushing, pulling and kneading of the muscle. A model for the rolling massage manipulation is proposed and the lattice Boltzmann method is applied to study the blood flow in the blood vessels. The simulation results show that the blood flux is considerably modified by the rolling massage and the explicit value depends on the rolling frequency, the rolling depth, and the diameter of the vessel. The smaller the diameter of the blood vessel, the larger the enhancement of the blood flux by the rolling massage. The model, together with the simulation results, is expected to be helpful to understand the mechanism and further development of rolling massage techniques.

Analysis of the differential gene and protein expression profile of the rolled leaf mutant of transgenic rice (Oryza sativa L.).

PubMed

Zhu, Qiuqiang; Yu, Shuguang; Chen, Guanshui; Ke, Lanlan; Pan, Daren

2017-01-01

The importance of leaf rolling in rice (Oryza sativa L.) has been widely recognized. Although several studies have investigated rice leaf rolling and identified some related genes, knowledge of the molecular mechanism underlying rice leaf rolling, especially outward leaf rolling, is limited. Therefore, in this study, differential proteomics and gene expression profiling were used to analyze rolled leaf mutant of transgenic rice in order to investigate differentially expressed genes and proteins related to rice leaf rolling. To this end, 28 differentially expressed proteins related to rolling leaf traits were isolated and identified. Digital expression profiling detected 10 genes related to rice leaf rolling. Some of the proteins and genes detected are involved in lipid metabolism, which is related to the development of bulliform cells, such as phosphoinositide phospholipase C, Mgll gene, and At4g26790 gene. The "omics"-level techniques were useful for simultaneously isolating several proteins and genes related to rice leaf rolling. In addition, the results of the analysis of differentially expressed proteins and genes were closely consistent with those from a corresponding functional analysis of cellular mechanisms; our study findings might form the basis for further research on the molecular mechanisms underlying rice leaf rolling.

Rolling friction—models and experiment. An undergraduate student project

NASA Astrophysics Data System (ADS)

Vozdecký, L.; Bartoš, J.; Musilová, J.

2014-09-01

In this paper the rolling friction (rolling resistance) model is studied theoretically and experimentally in undergraduate level fundamental general physics courses. Rolling motions of a cylinder along horizontal or inclined planes are studied by simple experiments, measuring deformations of the underlay or of the rolling body. The rolling of a hard cylinder on a soft underlay as well as of a soft cylinder on a hard underlay is studied. The experimental data are treated by the open source software Tracker, appropriate for use at the undergraduate level of physics. Interpretation of results is based on elementary considerations comprehensible to university students—beginners. It appears that the commonly accepted model of rolling resistance based on the idea of a warp (little bulge) on the underlay in front of the rolling body does not correspond with experimental results even for the soft underlay and hard rolling body. The alternative model of the rolling resistance is suggested in agreement with experiment and the corresponding concept of the rolling resistance coefficient is presented. In addition to the obtained results we can conclude that the project can be used as a task for students in practical exercises of fundamental general physics undergraduate courses. Projects of similar type effectively contribute to the development of the physical thinking of students.

A model for investigating the influence of road surface texture and tyre tread pattern on rolling resistance

NASA Astrophysics Data System (ADS)

Hoever, Carsten; Kropp, Wolfgang

2015-09-01

The reduction of rolling resistance is essential for a more environmentally friendly road transportation sector. Both tyre and road design can be utilised to reduce rolling resistance. In both cases a reliable simulation tool is needed which is able to quantify the influence of design parameters on the rolling resistance of a tyre rolling on a specific road surface. In this work a previously developed tyre/road interaction model is extended to account for different tread patterns and for losses due to small-scale tread deformation. Calculated contact forces and tyre vibrations for tyre/road interaction under steady-state rolling are used to predict rolling losses in the tyre. Rolling resistance is calculated for a series of different tyre/road combinations. Results are compared with rolling resistance measurements. The agreement between simulations and measurements is generally very good. It is found that both the tyre structure and small-scale tread deformations contribute to the rolling losses. The small-scale contribution depends mainly on the road roughness profile. The mean profile depth of the road surface is identified to correlate very well with the rolling resistance. Additional calculations are performed for non-traditional rubberised road surfaces, however, with mixed results. This possibly indicates the existence of additional loss mechanisms for these surfaces.

Analytical study on web deformation by tension in roll-to-roll printing process

NASA Astrophysics Data System (ADS)

Kang, Y. S.; Hong, M. S.; Lee, S. H.; Jeon, Y. H.; Kang, D.; Lee, N. K.; Lee, M. G.

2017-08-01

Recently, flexible devices have gained high intentions for flexible display, Radio Frequency Identification (RFID), bio-sensor and so on. For manufacturing of the flexible devices, roll-to-roll process is a good candidate because of its low production cost and high productivity. Flexible substrate has a non-uniform deformation distribution by tension. Because the roll-to-roll process carries out a number of overlay printing processes, the deformation affect overlay printing precision and printable areas. In this study, the deformation of flexible substrate was analyzed by using finite element analysis and it was verified through experiments. More deformation occurred in the middle region in the direction parallel to rolling of the flexible substrate. It is confirmed through experiments and analysis that deformation occurs less at the both ends than in the middle region. Based on these results, a hourglass roll is proposed as a mechanical design of the roll to compensate the non-uniform deformation of the flexible substrate. In the hourglass roll, high stiffness material is used in the core and low stiffness material such as an elastic material is wrapped. The diameter of the core roll was designed to be the minimum at the middle and the maximum at both ends. We tried to compensate the non-uniform deformation distribution of the flexible substrate by using the variation of the contact stiffness between the roll and the flexible substrate. Deformation distribution of flexible substrates was confirmed by finite element analysis by applying hourglass roll shape. In the analysis when using the hourglass roll, it is confirmed that the stress distribution is compensated by about 70% and the strain distribution is compensated by about 67% compared to the case using the hourglass roll. To verify the compensation of the non-uniform deformation distribution due to the tension, deformation measurement experiment when using the proposed hourglass roll was carried out. Experiments have shown that the distribution of deformation is compensated by about 34%. From the results, we verified the performance of the proposed.

25 CFR 75.3 - Announcement of revision of roll.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Announcement of revision of roll. 75.3 Section 75.3... ROLL OF THE EASTERN BAND OF CHEROKEE INDIANS, NORTH CAROLINA § 75.3 Announcement of revision of roll... perform the work necessary to revise the membership roll of the Band and such staff has been employed and...

25 CFR 75.3 - Announcement of revision of roll.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Announcement of revision of roll. 75.3 Section 75.3... ROLL OF THE EASTERN BAND OF CHEROKEE INDIANS, NORTH CAROLINA § 75.3 Announcement of revision of roll... perform the work necessary to revise the membership roll of the Band and such staff has been employed and...

The Six Track Scherzer Rolling Lift Bridge…Two double track spans ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

The Six Track Scherzer Rolling Lift Bridge…Two double track spans closed. One double-track span open. Photocopy of plate xvi in Scherzer Rolling Lift Bridge Company, Scherzer Rolling Lift Bridges. - New York, New Haven & Hartford Railroad, Fort Point Channel Rolling Lift Bridge, Spanning Fort Point Channel, Boston, Suffolk County, MA

78 FR 64473 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final No...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-29

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled... of subject merchandise to the United States during the POR. \\1\\ See Certain Hot-Rolled Carbon Steel...

Computer-aided roll pass design in rolling of airfoil shapes

NASA Technical Reports Server (NTRS)

Akgerman, N.; Lahoti, G. D.; Altan, T.

1980-01-01

This paper describes two computer-aided design (CAD) programs developed for modeling the shape rolling process for airfoil sections. The first program, SHPROL, uses a modular upper-bound method of analysis and predicts the lateral spread, elongation, and roll torque. The second program, ROLPAS, predicts the stresses, roll separating force, the roll torque and the details of metal flow by simulating the rolling process, using the slab method of analysis. ROLPAS is an interactive program; it offers graphic display capabilities and allows the user to interact with the computer via a keyboard, CRT, and a light pen. The accuracy of the computerized models was evaluated by (a) rolling a selected airfoil shape at room temperature from 1018 steel and isothermally at high temperature from Ti-6Al-4V, and (b) comparing the experimental results with computer predictions. The comparisons indicated that the CAD systems, described here, are useful for practical engineering purposes and can be utilized in roll pass design and analysis for airfoil and similar shapes.

Rolling Tobacco in Banana Leaves, Newspaper, or Copybook Paper Associated With Significant Reduction in Lung Function in Vanuatu.

PubMed

Weitz, Charles A; Olszowy, Kathryn M; Dancause, Kelsey N; Sun, Cheng; Pomer, Alysa; Silverman, Howard; Lee, G; Tarivonda, Len; Chan, Chim W; Kaneko, Akira; Lum, J K; Garruto, Ralph M

2017-04-01

In addition to the widespread availability of packaged cigarettes, the inhabitants of island nations of the Southwest Pacific frequently smoke commercially available loose tobacco using manufactured rolling papers, as well as locally grown tobacco rolled in manufactured rolling paper or wrapped in leaves, copybook paper, and newspaper. In this study, Vanuatu men who smoked local tobacco rolled in leaves, copybook paper, or newspaper showed significantly lower forced vital capacity (FVC), forced expiratory volume in 1 second (FEV 1 ), and FEV 1 /FVC ratios than men who smoked packaged cigarettes, store-bought tobacco rolled in manufactured rolling paper, or who smoked locally grown tobacco rolled in manufactured rolling papers. The addition of toxins from these unusual tobacco-wrapping media produces lung function deficits similar to the pattern noted among tobacco smokers who also inhale smoke from burning biomass. Thus, public health initiatives should consider including strategies addressing the use of wrapping media among smokers in South Pacific island societies.

Flight Test of the F/A-18 Active Aeroelastic Wing Airplane

NASA Technical Reports Server (NTRS)

Voracek, David

2007-01-01

A viewgraph presentation of flight tests performed on the F/A active aeroelastic wing airplane is shown. The topics include: 1) F/A-18 AAW Airplane; 2) F/A-18 AAW Control Surfaces; 3) Flight Test Background; 4) Roll Control Effectiveness Regions; 5) AAW Design Test Points; 6) AAW Phase I Test Maneuvers; 7) OBES Pitch Doublets; 8) OBES Roll Doublets; 9) AAW Aileron Flexibility; 10) Phase I - Lessons Learned; 11) Control Law Development and Verification & Validation Testing; 12) AAW Phase II RFCS Envelopes; 13) AAW 1-g Phase II Flight Test; 14) Region I - Subsonic 1-g Rolls; 15) Region I - Subsonic 1-g 360 Roll; 16) Region II - Supersonic 1-g Rolls; 17) Region II - Supersonic 1-g 360 Roll; 18) Region III - Subsonic 1-g Rolls; 19) Roll Axis HOS/LOS Comparison Region II - Supersonic (open-loop); 20) Roll Axis HOS/LOS Comparison Region II - Supersonic (closed-loop); 21) AAW Phase II Elevated-g Flight Test; 22) Region I - Subsonic 4-g RPO; and 23) Phase II - Lessons Learned

Roll-to-Roll production of carbon nanotubes based supercapacitors

NASA Astrophysics Data System (ADS)

Zhu, Jingyi; Childress, Anthony; Karakaya, Mehmet; Roberts, Mark; Arcilla-Velez, Margarita; Podila, Ramakrishna; Rao, Apparao

2014-03-01

Carbon nanomaterials provide an excellent platform for electrochemical double layer capacitors (EDLCs). However, current industrial methods for producing carbon nanotubes are expensive and thereby increase the costs of energy storage to more than 10 Wh/kg. In this regard, we developed a facile roll-to-roll production technology for scalable manufacturing of multi-walled carbon nanotubes (MWNTs) with variable density on run-of-the-mill kitchen Al foils. Our method produces MWNTs with diameter (heights) between 50-100 nm (10-100 μm), and a specific capacitance as high as ~ 100 F/g in non-aqueous electrolytes. In this talk, the fundamental challenges involved in EDLC-suitable MWNT growth, roll-to-roll production, and device manufacturing will be discussed along with electrochemical characteristics of roll-to-roll MWNTs. Research supported by NSF CMMI Grant1246800.

Effects of Changing Hot Rolling Direction on Microstructure, Texture and Mechanical Properties of Cu-2.7Be Sheets

NASA Astrophysics Data System (ADS)

Zhu, Daibo; Liu, Chuming; Yu, Haijun; Han, Tan

2018-03-01

A hot rolling scheme (cross-rolling and unidirectional rolling) was adopted to process Cu-2.7Be sheets used as multiplier dynodes in photomultiplier. The effects of changing rolling direction on microstructure, texture and mechanical properties were studied by a combination of XRD, EBSD and TEM. It was found that higher copper-type texture and lower brass texture intensity were obtained in the ultimately cross-rolling (CR) sheet compared with the unidirectional rolling (UR) sheet.The EBSD results indicated that the grain orientation from mainly < {101} > for UR sample turns to random for CR sample. Great enhancements in YS and UTS after unidirectional rolling were attributed to the massive and polygonal γ precipitates. The CR sample exhibited lower anisotropy, because of the increase of S and γ precipitates with spherical and tiny shape.

Impact of vertical wind shear on roll structure in idealized hurricane boundary layers

NASA Astrophysics Data System (ADS)

Wang, Shouping; Jiang, Qingfang

2017-03-01

Quasi-two-dimensional roll vortices are frequently observed in hurricane boundary layers. It is believed that this highly coherent structure, likely caused by the inflection-point instability, plays an important role in organizing turbulent transport. Large-eddy simulations are conducted to investigate the impact of wind shear characteristics, such as the shear strength and inflection-point level, on the roll structure in terms of its spectral characteristics and turbulence organization. A mean wind nudging approach is used in the simulations to maintain the specified mean wind shear without directly affecting turbulent motions. Enhancing the radial wind shear expands the roll horizontal scale and strengthens the roll's kinetic energy. Increasing the inflection-point level tends to produce a narrow and sharp peak in the power spectrum at the wavelength consistent with the roll spacing indicated by the instantaneous turbulent fields. The spectral tangential momentum flux, in particular, reaches a strong peak value at the roll wavelength. In contrast, the spectral radial momentum flux obtains its maximum at the wavelength that is usually shorter than the roll's, suggesting that the roll radial momentum transport is less efficient than the tangential because of the quasi-two-dimensionality of the roll structure. The most robust rolls are produced in a simulation with the highest inflection-point level and relatively strong radial wind shear. Based on the spectral analysis, the roll-scale contribution to the turbulent momentum flux can reach 40 % in the middle of the boundary layer.

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2013 CFR

2013-07-01

... section. (2) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface...

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface. Ensure...

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... section. (2) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface...

The measurement of dynamic radii for passenger car tyre

NASA Astrophysics Data System (ADS)

Anghelache, G.; Moisescu, R.

2017-10-01

The tyre dynamic rolling radius is an extremely important parameter for vehicle dynamics, for operation of safety systems as ESP, ABS, TCS, etc., for road vehicle research and development, as well as for validation or as an input parameter of automotive simulations and models. The paper investigates the dynamic rolling radii of passenger car tyre and the influence of rolling speed and inflation pressure on their magnitude. The measurement of dynamic rolling radii has been performed on a chassis dynamometer test rig. The dynamic rolling radii have been measured indirectly, using longitudinal rolling speed and angular velocity of wheel. Due to the subtle effects that the parameters have on rolling radius magnitude, very accurate equipment has to be used. Two different methods have been chosen for measuring the wheel angular velocity: the stroboscopic lamp and the incremental rotary encoder. The paper shows that the stroboscopic lamp has an insufficient resolution, therefore it was no longer used for experimental investigation. The tyre dynamic rolling radii increase with rolling speed and with tyre inflation pressure, but the effect of pressure is more significant. The paper also makes considerations on the viability of simplified formulae from literature for calculating the tyre dynamic rolling radius.

Environmentally Acceptable Medium Caliber Ammunition Percussion Primers

DTIC Science & Technology

2007-10-31

tetrazol-5-amino)-s-tetrazine or Bis-aminotetrazolyl-tetrazine CAD Cartridge Actuated Device CFR Code of Federal Regulations cm Centimeter cm3...approximately 120mg each, were placed on the Plexiglas slab . The piles were separated by a potassium chloride window estimated to transmit at least...for cartridge actuated device/propellant actuated device ( CAD /PAD) application. The NSWC-IH was working with the SDSMT and IMP in developing unique

Broaching the Ship: Rethinking Submarines as a Signaling Tool in Naval Diplomacy

DTIC Science & Technology

2015-03-01

late Nineteenth Century and the late Industrial Revolution, steam power, rifled barrels and steel armor supplanted sailing ships and smoothbore...them to not only construct steel ships but also innovate and incorporate news designs of all types. This period saw changes in battleship...entirely by steam. Improvements in gun design and propellant charges yielded ever-larger calibers of naval rifle with ever-increasing range. Steel

Exploratory Development of New and Improved Self-Sealing Materials for Fuel Lines

DTIC Science & Technology

1974-10-01

identify hy block number) New and improved self-sealing fuel line composites were developed under this program. Fabric reinforced plastic and nonflowering...integrated aluminum foil, fabric reinforced laminated fuel line composites employing compressed natural rubber foam as the sealant were fabricated which...successfully sealed wounds inflicted by .30 and .50 caliber projectiles. The weight of these new self-sealing fuel line composites ranged from 0.83

The United States Army Medical Department Journal, July-September 2009

DTIC Science & Technology

2009-09-01

have contributed an excellent article reporting a formal study they performed in Kenya evaluating deet in comparison with 4 other commercially...article is another excellent example of the high caliber of work being performed every day by the US military’s dedicated scientific professionals in...impact on US military personnel deployed to southeast Asia and the Pacific islands that the military initiated a research project performed by the

Refractory Metal Liner Processing for M242 Medium Caliber Barrels

DTIC Science & Technology

2013-01-01

3 Figure 3. Measured hoop strain as a function of axial position for first 12-in steel cylinder. ........4 Figure 4. Hoop strain...measurements as a function of axial position for the second steel cylinder (8-in and 4-in plugs...A compression load of 160,000 lb was used for the second tube in order to obtain some plastic deformation of the steel cylinder; this load gave an

Boundary Layer Studies on a Spinning Tangent-Ogive-Cylinder Model

DTIC Science & Technology

1975-07-01

ca) An experimental investigation of the Magnus effect on a seven caliber tangent-I ;’ ogive- cylinder model in supersonic flow is reported. The...necessary and Identify by block number) Three-Dimiensional Boundary Layer Compressible Flow Body of Revolution Magnus Effects Boundary Layer...factors have resulted in renewed interest in the study of the Magnus effect . This report describes an experimental study of the effects of spin on

Bio-inspired Armor Protective Material Systems for Ballistic Shock Mitigation

DTIC Science & Technology

2011-01-01

Coupon testing a b s t r a c t Severe transient ballistic shocks from projectile impacts, mine blasts , or overhead artillery attacks can incapacitate an...past two decades [1]. A ballistic shock results from a significant amount of concentrated energy deposited from caliber projectile impacts, mine blasts ...LS- Dyna , has been predominately utilized to calculate the target shock responses including acceleration histo- ries, shock response spectra

Manufacturing Methods and Technology Project Summary Reports

DTIC Science & Technology

1985-06-01

Computer -Aided Design (CAD)/ Computer -Aided Manufacturing (CAM) Process for the Production of Cold Forged Gears Project 483 6121 - Robotic Welding and...Caliber Projectile Bodies Project 682 8370 - Automatic Inspection and 1-I1 Process Control of Weapons Parts Manufacturing METALS Project 181 7285 - Cast...designed for use on each project. Experience suggested that a general purpose computer interface might be designed that could be used on any project

Stereo Vision Inside Tire

DTIC Science & Technology

2015-08-21

using the Open Computer Vision ( OpenCV ) libraries [6] for computer vision and the Qt library [7] for the user interface. The software has the...depth. The software application calibrates the cameras using the plane based calibration model from the OpenCV calib3D module and allows the...6] OpenCV . 2015. OpenCV Open Source Computer Vision. [Online]. Available at: opencv.org [Accessed]: 09/01/2015. [7] Qt. 2015. Qt Project home

Experimental Evaluation of Cold-Sprayed Copper Rotating Bands for Large-Caliber Projectiles

DTIC Science & Technology

2015-05-01

ABSTRACT A copper rotating band is the munition component responsible for both obturation and transfer of torque from the gun barrel’s rifling to the...munition, thereby causing the projectile to spin. Pure copper, copper alloy, and brass rotating bands are typically fabricated to steel munitions using...Machine Shop for fabrication; and the Transonic Experimental Facility for facilitating the gun -launch experiments. vi INTENTIONALLY LEFT BLANK

Physical Mechanisms of Soft Tissue Injury from Penetrating Ballistic Impact

DTIC Science & Technology

2012-11-30

SUPPLEMENTARY NOTES 14. ABSTRACT Most civilian nonfatal gunshot injuries and murders involve handguns . Gunshot wounds are often classified as being due to...high-velocity or low-velocity projectiles, e.g. rifle or handgun rounds. However, this is a historical distinction, and there is overlap in energy...that can be delivered to tissue by modern rifle and handgun rounds. Also, the same diameter (caliber) bullet can have different impact energies

Ship to Shore Connector Amphibious Craft (SSC)

DTIC Science & Technology

2015-12-01

M2 .50 Caliber (12.7mm) Machine Gun ...MK19 40mm Grenade Machine Gun and M60/M240 Series 7.62mm Light Machine Gun . TBD The SSC shall provide protection to the crew and internally... Machine Gun , MK19 40mm Grenade Machine Gun and M60/M240 Series 7.62mm Light Machine Gun . Survivability (Sea-Worthiness) T=O The SSC shall be

Check Firing of Master and Reference Propellants

DTIC Science & Technology

2014-12-08

estimate amount and color of smoke generated. s. Visually estimate amount and color of muzzle flash generated. TOP 04-2-607A 8 December 2014 10...Stargauge. TOP 04-2-607A 8 December 2014 3 e. Pressure gauge (piezoelectric preferred, and/or crusher). f. Muzzle velocity radar unit...firing: a. Provide electronics personnel with the weapon caliber and type, the weight and model of projectile, and expected muzzle velocities. b

An Evaluation of Liquid Explosives for Foxhole Digging

DTIC Science & Technology

1978-04-01

Silicone dioxide 1.93 - - Other x .76 - - Amonium nitrate - 49 80 Ammonia 9.95 - - Solid Ammonium perchlorate...1978 D D C AUG 24 1978 |j j - Av-’- US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND LARGE CALIBER ’ WEAPON SYSTEMS LABORATORY DOVER. NEW...Entered) U& d <L$. UNr.T.ASSTFTFn SECURITY CLASSIFICATION OF THIS PAOEfWfun Palm Etttfd) 20. (Cont’d) After testing, the liquid NM/NE/RDX was

A Technical Assessment of Electromagnetic Propulsion for Small Caliber Weapons Applications

DTIC Science & Technology

1990-11-01

viii ACKNOWLEDGMENTS The author is grateful to Mr. Alex Zielinski , Dr. C. E. Hollandsworth, and Mr. Henry Burden for their efforts in the technical...stabilized ( Zielinski and Garner 1990). The design has undergone some preliminary testing and is awaiting higher velocity testing. In addition, some...aerodynamic flight characterization has been performed on these types of projectiles launched from a high pressure propellant gun (Garner, Zielinski , and

Adaptive attenuation of aliased ground roll using the shearlet transform

NASA Astrophysics Data System (ADS)

Hosseini, Seyed Abolfazl; Javaherian, Abdolrahim; Hassani, Hossien; Torabi, Siyavash; Sadri, Maryam

2015-01-01

Attenuation of ground roll is an essential step in seismic data processing. Spatial aliasing of the ground roll may cause the overlap of the ground roll with reflections in the f-k domain. The shearlet transform is a directional and multidimensional transform that separates the events with different dips and generates subimages in different scales and directions. In this study, the shearlet transform was used adaptively to attenuate aliased and non-aliased ground roll. After defining a filtering zone, an input shot record is divided into segments. Each segment overlaps adjacent segments. To apply the shearlet transform on each segment, the subimages containing aliased and non-aliased ground roll, the locations of these events on each subimage are selected adaptively. Based on these locations, mute is applied on the selected subimages. The filtered segments are merged together, using the Hanning function, after applying the inverse shearlet transform. This adaptive process of ground roll attenuation was tested on synthetic data, and field shot records from west of Iran. Analysis of the results using the f-k spectra revealed that the non-aliased and most of the aliased ground roll were attenuated using the proposed adaptive attenuation procedure. Also, we applied this method on shot records of a 2D land survey, and the data sets before and after ground roll attenuation were stacked and compared. The stacked section after ground roll attenuation contained less linear ground roll noise and more continuous reflections in comparison with the stacked section before the ground roll attenuation. The proposed method has some drawbacks such as more run time in comparison with traditional methods such as f-k filtering and reduced performance when the dip and frequency content of aliased ground roll are the same as those of the reflections.

Effect of intermediate annealing on the microstructure and mechanical property of ZK60 magnesium alloy produced by twin roll casting and hot rolling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Hongmei, E-mail: hmchen@just.edu.cn; Zang, Qianhao; Yu, Hui

2015-08-15

Twin roll cast (designated as TRC in short) ZK60 magnesium alloy strip with 3.5 mm thickness was used in this paper. The TRC ZK60 strip was multi-pass rolled at different temperatures, intermediate annealing heat treatment was performed when the thickness of the strip changed from 3.5 mm to 1 mm, and then continued to be rolled until the thickness reached to 0.5 mm. The effect of intermediate annealing during rolling process on microstructure, texture and room temperature mechanical properties of TRC ZK60 strip was studied by using OM, TEM, XRD and electronic universal testing machine. The introduction of intermediate annealingmore » can contribute to recrystallization in the ZK60 sheet which was greatly deformed, and help to reduce the stress concentration generated in the rolling process. Microstructure uniformity and mechanical properties of the ZK60 alloy sheet were also improved; in particular, the room temperature elongation was greatly improved. When the TRC ZK60 strip was rolled at 300 °C and 350 °C, the room temperature elongation of the rolled sheet with 0.5 mm thickness which was intermediate annealed during the rolling process was increased by 95% and 72% than that of no intermediate annealing, respectively. - Highlights: • Intermediate annealing was introduced during hot rolling process of twin roll cast ZK60 alloy. • Intermediate annealing can contribute to recrystallization and reduce the stress concentration in the deformed ZK60 sheet. • Microstructure uniformity and mechanical properties of the ZK60 sheet were improved, in particular, the room temperature elongation. • The elongation of the rolled ZK60 sheet after intermediate annealed was increased by 95% and 72% than that of no intermediate annealing.« less

Experimental investigation of the effects of aft blowing with various nozzle exit geometries on a 3.0 caliber tangent ogive at high angles of attack: Forebody pressure distributions

NASA Technical Reports Server (NTRS)

Chokani, Ndaona; Gittner, N. M.

1992-01-01

An experimental study of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was studied. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were studied and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Flat epithelial atypia of the breast on core needle biopsy: an indication for surgical excision.

PubMed

Sohn, Vance; Porta, Rees; Brown, Tommy

2011-11-01

Flat epithelial atypia (FEA) is an increasingly diagnosed breast lesion yet there remains a paucity of data regarding these findings and their clinical significance. By determining the pathologic concordance rate, we sought to evaluate the indications for surgical intervention for FEAs diagnosed on core needle biopsy (CNB). Using a retrospective review of an international pathology referral center database, we included all breast CNB specimens with FEA as the most advanced diagnosis that underwent surgical excision. Patient demographics, caliber of biopsy needle, and pathology results were then analyzed. Between 2000 and 2009, 463 FEAs were diagnosed among 15,000 specimens referred for expert opinion. Twenty-four lesions (5%) met inclusion criteria. Sampling ranged from 8- to 18-guage needles. Two lesions (8.4%) were upgraded after surgical excision; one patient was found to have infiltrating ductal carcinoma and another with tubular carcinoma. Twelve patients who were diagnosed with FEA did not undergo surgical excision but had no immediate evidence of malignancy. Based on the 8.4% upgrade rate, FEA diagnosed on CNB requires follow-up surgical excision. Regardless of CNB caliber, the risk of sampling error precludes nonoperative management and FEA should be considered an at-risk lesion until more studies and pooled analysis prove otherwise.

Therapeutic Efficacy of a Combination Therapy of Topical 17α-Estradiol and Topical Minoxidil on Female Pattern Hair Loss: A Noncomparative, Retrospective Evaluation

PubMed Central

Choe, Sung Jay; Lee, Solam; Choi, Jaewoong

2017-01-01

Background A variety of agents have been used to treat female pattern hair loss (FPHL), including topical minoxidil, topical 17α-estradiol, oral anti-androgen agents, and mineral supplements. Compared with these single agent regimens, combination therapies could be a better therapeutic option in expectation of superior treatment outcome. Objective This study was designed to determine the efficacy of a combination therapy consisting of topical 0.025% 17α-estradiol and 3% minoxidil in Korean patients with FPHL. Methods Therapeutic efficacy was evaluated in 34 women who applied topical 0.025% 17α-estradiol and 3% minoxidil once daily for more than 6 months. Phototrichogram analysis was performed before and after therapy. The efficacy was evaluated with respect to total hair count, hair caliber (as assessed by phototrichogram analysis), and photographic assessment. Results Total hair count and hair caliber both increased from baseline to 6 months in patients treated with the combination therapy of topical 0.025% 17α-estradiol and 3% minoxidil (p<0.001). Photographic assessment also revealed significant disease improvement, thus supporting the therapeutic efficacy. Conclusion A combination therapy consisting of topical 0.025% 17α-estradiol and 3% minoxidil can be tried as an effective treatment for FPHL. PMID:28566902

Microsurgical Decompression of the Cochlear Nerve to Treat Disabling Tinnitus via an Endoscope-Assisted Retrosigmoid Approach: The Padua Experience.

PubMed

Di Stadio, Arianna; Colangeli, Roberta; Dipietro, Laura; Martini, Alessandro; Parrino, Daniela; Nardello, Ennio; D'Avella, Domenico; Zanoletti, Elisabetta

2018-05-01

The use of surgical cochlear nerve decompression is controversial. This study aimed at investigating the safety and validity of microsurgical decompression via an endoscope-assisted retrosigmoid approach to treat tinnitus in patients with neurovascular compression of the cochlear nerve. Three patients with disabling tinnitus resulting from a loop in the internal auditory canal were evaluated with magnetic resonance imaging and tests of pure tone auditory, tinnitus, and auditory brain response (ABR) to identify the features of the cochlear nerve involvement. We observed a loop with a caliber greater than 0.8 mm in all patients. Patients were treated via an endoscope-assisted retrosigmoid microsurgical decompression. After surgery, none of the patients reported short-term or long-term complications. After surgery, tinnitus resolved immediately in 2 patients, whereas in the other patient symptoms persisted although they improved; in all patients, hearing was preserved and ABR improved. Microsurgical decompression via endoscope-assisted retrosigmoid approach is a promising, safe, and valid procedure for treating tinnitus caused by cochlear nerve compression. This procedure should be considered in patients with disabling tinnitus who have altered ABR and a loop that has a caliber greater than 0.8 mm and is in contact with the cochlear nerve. Copyright © 2018 Elsevier Inc. All rights reserved.

Retinal changes in diabetic patients without diabetic retinopathy.

PubMed

Dumitrescu, Alina Gabriela; Istrate, Sinziana Luminita; Iancu, Raluca Claudia; Guta, Oana Maria; Ciuluvica, Radu; Voinea, Liliana

2017-01-01

The purpose of this study was to measure retinal vessel caliber and to examine early changes in macular thickness using optical coherence tomography (OCT). We evaluated to what extend vascular caliber and macular thickness differed between patients with type 2 diabetes mellitus without diabetic retinopathy compared with healthy individuals. 26 diabetic patients without diabetic retinopathy and 26 normal participants without any retinal and optic nerve diseases underwent ophthalmic examination, fundus photography, and OCT imaging. Temporal inferior retinal vessel diameters were measured using OCT. Also, we measured macular thickness in nine ETDRS subfields using Cirrus OCT. The mean age in the diabetic group was 61.5 years and in the control group, 55.5 years. Wider retinal arterioles and venules were found in patients with diabetes compared with healthy subjects (120 µm versus 96 µm, p<0.005 and 137 µm versus 120.5 µm, p value <0.001, respectively). In patients with type 2 diabetes mellitus, central macular thickness was significantly thinner than that of control eyes (243.5 µm versus 269.9 µm, p value <0.001). Our results support the hypothesis that the association between vascular damage and structural changes of the neuroretina is an early indicator of retinal impairment in patients with diabetes without diabetic retinopathy.

A doctor of the highest caliber treats an illness before it happens.

PubMed

Zhan, Mei

2009-01-01

"A doctor of the highest caliber treats an illness before it happens," a seemingly antiquated doctrine in traditional Chinese medicine, is enjoying surging popularity among practitioners in urban China and the United States today. In this essay, I examine how the meanings and contours of traditional Chinese medicine have shifted in recent decades as it is molded into a "preventive medicine" through translocal encounters. From the 1960s and the early 1970s, the emphasis China's socialist health care placed on preventive health among the rural poor shaped the practice of Chinese herbal medicine and especially acupuncture. This version of preventive medicine was also exported to the Third World, which China strove to champion. Since the end of the Cold War and especially during the 1990s, as China strives to "get on track with the world" (specifically, affluent nation-states, especially in North America and the European Union), traditional Chinese medicine has been rapidly commodified and reinvented as a new kind of preventive medicine tailored for cosmopolitan, middle-class lifestyles. The emergence of this radically new preventive medicine resuscitates certain stories of antiquity and continuity, emphasizing that traditional Chinese medicine has always been "preventive" while obliterating recent memories of the proletariat world and its preventive medicine.

Retinopathy and chronic kidney disease in the Chronic Renal Insufficiency Cohort (CRIC) study.

PubMed

Grunwald, Juan E; Alexander, Judith; Ying, Gui-Shuang; Maguire, Maureen; Daniel, Ebenezer; Whittock-Martin, Revell; Parker, Candace; McWilliams, Kathleen; Lo, Joan C; Go, Alan; Townsend, Raymond; Gadegbeku, Crystal A; Lash, James P; Fink, Jeffrey C; Rahman, Mahboob; Feldman, Harold; Kusek, John W; Xie, Dawei; Jaar, Bernard G

2012-09-01

To investigate the association between retinopathy and chronic kidney disease. In this observational, cross-sectional study, 2605 patients of the Chronic Renal Insufficiency Cohort (CRIC) study, a multicenter study of chronic kidney disease, were offered participation. Nonmydriatic fundus photographs of the disc and macula in both eyes were obtained in 1936 of these subjects. The photographs were reviewed in a masked fashion at a central photograph reading center using standard protocols. Presence and severity of retinopathy (diabetic, hypertensive, or other) and vessel diameter caliber were assessed by trained graders and a retinal specialist using protocols developed for large epidemiologic studies. Kidney function measurements and information on traditional and nontraditional risk factors for decreased kidney function were obtained from the CRIC study. Greater severity of retinopathy was associated with lower estimated glomerular filtration rate after adjustment for traditional and nontraditional risk factors. The presence of vascular abnormalities usually associated with hypertension was also associated with lower estimated glomerular filtration rate. We found no strong direct relationship between estimated glomerular filtration rate and average arteriolar or venular calibers. Our findings show a strong association between severity of retinopathy and its features and level of kidney function after adjustment for traditional and nontraditional risk factors for chronic kidney disease, suggesting that retinovascular pathology reflects renal disease.

A stereoscopic imaging system for laser back scatter based trajectory measurement in ballistics: part 2

NASA Astrophysics Data System (ADS)

Chalupka, Uwe; Rothe, Hendrik

2012-03-01

The progress on a laser- and stereo-camera-based trajectory measurement system that we already proposed and described in recent publications is given. The system design was extended from one to two more powerful, DSP-controllable LASER systems. Experimental results of the extended system using different projectile-/weapon combinations will be shown and discussed. Automatic processing of acquired images using common 3DIP techniques was realized. Processing steps to extract trajectory segments from images as representative for the current application will be presented. Used algorithms for backward-calculation of the projectile trajectory will be shown. Verification of produced results is done against simulated trajectories, once in terms of detection robustness and once in terms of detection accuracy. Fields of use for the current system are within the ballistic domain. The first purpose is for trajectory measurement of small and middle caliber projectiles on a shooting range. Extension to big caliber projectiles as well as an application for sniper detection is imaginable, but would require further work. Beside classical RADAR, acoustic and optical projectile detection methods, the current system represents a further projectile location method under the new class of electro-optical methods that have been evolved in recent decades and that uses 3D imaging acquisition and processing techniques.

[Pathological anatomy of chagasic megaesophagus].

PubMed

Adad, S J; Andrade, D C; Lopes, E R; Chapadeiro, E

1991-01-01

Systematized study was made in 56 esophagi of chronic chagasics (17 with and 39 without megas) aiming to: 1) to evaluate the esophageal caliber and thickness ranges; 2) analyse qualitative and quantitatively, the myenteric plexuses, trying to evaluate the relation of their lesions and the development of megaesophagus (ME); 3) study the lesions of the muscularis propria to verify if they contribute or not to the beginning of the process; 4) search for T. cruzi and its eventual relationship with the inflammation; 5) identify the principal mucosal alterations. It was confirmed that the severest lesions were found in the muscularis propria and in the plexures of Auerbach ganglia. In the former, the main alterations were myositis and fibrosis. The myentric plexuses showed inflammation and neuronal depopulation when compared with non-mega chagasic esophagi and even more when compared with the controls. On the other hand, there were normal caliber esophagi with severe denervation. It is possible that several factors may lead to the esophagopathy, especially to the ME. The search for T. cruzi was found positive in four out of eight esophagi with mega and in none of eight chagasic esophagi without mega. Mucosal and submucosal lesions were unremarkable and do not seem to be involved with the development of the process.

Personal noise exposure assessment from small firearms

NASA Astrophysics Data System (ADS)

Kardous, Chucri A.; Murphy, William J.; Willson, Robert D.

2003-04-01

The National Institute for Occupational Safety and Health conducted noise exposure evaluations of law-enforcement personnel during firearms training at indoor and outdoor firing ranges. A representative cross section of weapons used by officers was measured. Shooters participated in live-fire exercise at an indoor firing range using three different weapons: a Beretta .400 caliber pistol, a Remington 12-gauge shotgun, and an M4 .223-caliber assault rifle. Indoor and outdoor measurements were obtained for the Smith and Wesson .357 pistol and Colt .450 and 9-mm pistols, the Glock .400 pistol, and the Heckler and Koch and Colt AR15 .223 rifles. Impulses were measured using a Bruel and Kjaer 4136 1/4-in. microphone and TASCAM digital audio tape recorder. Relevant impulse noise metrics were calculated. Peak levels ranged from 155 to 168 dB SPL. A-weighted equivalent levels ranged from 124 to 128 dBA. The contributions of the secondary weapon firings were approximately 1 to 9 dBA. Other parameters such as A/B durations, number and mixture of impulses, spectral content, energy, kurtosis, temporal spacing, and hearing protectors' effectiveness were examined. Comparisons of applicable damage risk criteria are presented. Further studies are needed to establish an occupational impulse noise damage risk criterion.

Viability of Bismuth as a Green Substitute for Lead in Jacketed .357 Magnum Revolver Bullets

NASA Astrophysics Data System (ADS)

Jenkins, Joel

In seeking to develop environmentally friendly lead-free non-toxic bullets, the research ballistically evaluated the performance of copper-jacketed handgun bullets containing a pure bismuth core. The lead was first removed from 140 grain Hornady(TM) XTPRTM bullets of 38 caliber (.357 diameter) by melting. The empty jackets were then refilled with pure bismuth, including the forming of a correctly sized hollow-point cavity. Due to the lower density of bismuth as compared to lead, the bismuth-cored bullets consistently weighed 125 gains. Conveniently this allowed direct comparison to commercially available 125 grain Hornady(TM) XTPRTM lead-cored bullets of 38 caliber. Both bismuth-cored and lead-cored versions of the 125 grain bullets had identical nose dimensions and jacket material, the only dimensional difference being the bullet length below the cannelure. Shooting took place at an outdoor range using a 357 Magnum Ruger(TM) SP101RTM revolver with 3" barrel as the test weapon. FBI protocols were followed when firing through clothing, wallboard, plywood, steel plates and laminated glass. Wound paths and bullets were captured in ballistic gelatin, with data collected for velocity, penetration, expansion, and weight retention. Bismuth compared favorably with lead in all but the laminated glass test, where it under penetrated due to jacket separation.

Complicated vascular access port removals: incidence, antecedents and avoidance.

PubMed

Teague, Warwick J; Fouad, Dina; Munro, Fraser D; McCabe, Amanda J

2015-09-01

Port removal is usually a straightforward procedure delegated to trainees. However, some port removals are complicated by central venous catheter (CVC) fragmentation, a challenge for even experienced surgeons. This study aimed to determine the incidence of, and risk factors for, complicated port removal in children. A single-centre study assessed the outcome of removal for all paediatric ports inserted from 1996 to 2012. Data were recorded detailing patient, insertion, device and removal characteristics. Risk factors for complicated removals were scrutinised using Chi-square tests; p < 0.05 significant. Of 628 ports inserted from 1996 to 2012, 443 were subsequently removed at the same centre. 8/443 (1.8%) removals were complicated by CVC fragmentation, a median of 3.3 (2.4-3.9) years after insertion. Of complicated cases, 8/8 underwent formal neck dissection, 3/8 intravascular dissection, and 1/8 endovascular retrieval. 2/8 cases have retained intravascular CVC fragments. Risk factors for complication were CVC caliber <6Fr (p < 0.001) and use duration >2 years (p < 0.001). Greatest care and senior supervision should be ensured when removing ports with CVC caliber <6Fr and/or >2 years since insertion. However, complications also occur with larger CVCs or after shorter durations. Therefore, the key to avoiding complicated port removal may simply be: preparation, preparation, neck preparation.

Characterization and discrimination of large caliber gun blast and flash signatures

NASA Astrophysics Data System (ADS)

Steward, Bryan J.; Gross, Kevin C.; Perram, Glen P.

2012-06-01

Two hundred and one firings of three 152 mm howitzer munitions were observed to characterize firing signatures of a large caliber gun. Muzzle blast expansion was observed with high-speed (1600 Hz) optical imagery. The trajectory of the blast front was well approximated by a modified point-blast model described by constant rate of energy deposition. Visible and near-infrared (450 - 850 nm) spectra of secondary combustion were acquired at ~0.75 nm spectral resolution and depict strong contaminant emissions including Li, Na, K, Cu, and Ca. The O2 (X-->b) absorption band is evident in the blue wing of the potassium D lines and was used for monocular passive ranging accurate to within 4 - 9%. Timeresolved midwave infrared (1800 - 6000 cm-1) spectra were collected at 100 Hz and 32 cm-1 resolution. A low dimensional radiative transfer model was used to characterize plume emissions in terms of area, temperature, soot emissivity, and species concentrations. Combustion emissions have ~100 ms duration, 1200 - 1600 K temperature, and are dominated by H2O and CO2. Non-combusting plume emissions last ~20 ms, are 850 - 1050 K, and show significant continuum (emissivity ~0.36) and CO structure. Munitions were discriminated with 92 - 96% classification accuracy using only 1 - 3 firing signature features.

Characterization and discrimination of large caliber gun blast and flash signatures

NASA Astrophysics Data System (ADS)

Steward, Bryan J.

Two hundred and one firings of three 152 mm howitzer munitions were observed to characterize firing signatures of a large caliber gun. Muzzle blast expansion was observed with high-speed (1600 Hz) optical imagery. The trajectory of the blast front was well approximated by a modified point-blast model described by constant rate of energy deposition. Visible and near-infrared (450--850 nm) spectra of secondary combustion were acquired at ˜0.75 nm spectral resolution and depict strong contaminant emissions including Li, Na, K, Cu, and Ca. The O2 (X→b) absorption band is evident in the blue wing of the potassium D lines and was used for monocular passive ranging accurate to within 4--9%. Time-resolved midwave infrared (1800--6000 cm-1) spectra were collected at 100 Hz and 32 cm-1 resolution. A low dimensional radiative transfer model was used to characterize plume emissions in terms of area, temperature, soot emissivity, and species concentrations. Combustion emissions have ~100 ms duration, 1200--1600 K temperature, and are dominated by H2O and CO2. Non-combusting plume emissions last ~20 ms, are 850--1050 K, and show significant continuum (emissivity ˜0.36) and CO structure. Munitions were discriminated with 92--96% classification accuracy using only 1--3 firing signature features.

Therapeutic Efficacy of a Combination Therapy of Topical 17α-Estradiol and Topical Minoxidil on Female Pattern Hair Loss: A Noncomparative, Retrospective Evaluation.

PubMed

Choe, Sung Jay; Lee, Solam; Choi, Jaewoong; Lee, Won-Soo

2017-06-01

A variety of agents have been used to treat female pattern hair loss (FPHL), including topical minoxidil, topical 17α-estradiol, oral anti-androgen agents, and mineral supplements. Compared with these single agent regimens, combination therapies could be a better therapeutic option in expectation of superior treatment outcome. This study was designed to determine the efficacy of a combination therapy consisting of topical 0.025% 17α-estradiol and 3% minoxidil in Korean patients with FPHL. Therapeutic efficacy was evaluated in 34 women who applied topical 0.025% 17α-estradiol and 3% minoxidil once daily for more than 6 months. Phototrichogram analysis was performed before and after therapy. The efficacy was evaluated with respect to total hair count, hair caliber (as assessed by phototrichogram analysis), and photographic assessment. Total hair count and hair caliber both increased from baseline to 6 months in patients treated with the combination therapy of topical 0.025% 17α-estradiol and 3% minoxidil ( p <0.001). Photographic assessment also revealed significant disease improvement, thus supporting the therapeutic efficacy. A combination therapy consisting of topical 0.025% 17α-estradiol and 3% minoxidil can be tried as an effective treatment for FPHL.

Design and fabrication of novel polymeric biodegradable stents for small caliber blood vessels by computer-aided wet-spinning.

PubMed

Puppi, D; Pirosa, A; Lupi, G; Erba, P A; Giachi, G; Chiellini, F

2017-06-07

Biodegradable stents have emerged as one of the most promising approaches in obstructive cardiovascular disease treatment due to their potential in providing mechanical support while it is needed and then leaving behind only the healed natural vessel. The aim of this study was to develop polymeric biodegradable stents for application in small caliber blood vessels. Poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyhexanoate] (PHBHHx), a renewable microbial aliphatic polyester, and poly(ε-caprolactone), a synthetic polyester approved by the US Food and Drug Administration for different biomedical applications, were investigated as suitable polymers for stent development. A novel manufacturing approach based on computer-aided wet-spinning of a polymeric solution was developed to fabricate polymeric stents. By tuning the fabrication parameters, it was possible to develop stents with different morphological characteristics (e.g. pore size and wall thickness). Thermal analysis results suggested that material processing did not cause changes in the molecular structure of the polymers. PHBHHx stents demonstrated great radial elasticity while PCL stents showed higher axial and radial mechanical strength. The developed stents resulted able to sustain proliferation of human umbilical vein endothelial cells within two weeks of in vitro culture and they showed excellent results in terms of thromboresistivity when in contact with human blood.

Railroad Classification Yard Technology Manual. Volume III. Freight Car Rollability

DOT National Transportation Integrated Search

1981-07-01

The report presents a survey of rolling resistance research, histograms of rolling resistance from five yards, a statistical regression analysis of causal factors affecting rolling resistance, procedures for constructing a rolling resistance histogra...

THE EFFECTS OF $gamma$-IRRADIATION AND ROLLING ON THE TEARING PROPERTIES OF POLYETHYLENE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsunekawa, Y.; Awatani, J.; Kojima, K.

1961-01-01

Polyethylene samples of 2 mm thickness were gamma irradiated in water. The total dosage for the samples irradiated after the rolling treatraent was 1.5 x lO/sup 5/ r/hr, while the dosage for the saraples irradiated before the rolling was 1.2 x lO/sup 5/ r/hr. The tensile strength of the irradiated and rolled saraple increased with increasing dosage. A comparison of tearing strengths between the rolled samples and the rolled and irradiated samples was raade. (OID)

The role of compressional viscoelasticity in the lubrication of rolling contacts.

NASA Technical Reports Server (NTRS)

Harrison, G.; Trachman, E. G.

1972-01-01

A simple model for the time-dependent volume response of a liquid to an applied pressure step is used to calculate the variation with rolling speed of the traction coefficient in a rolling contact system. Good agreement with experimental results is obtained at rolling speeds above 50 in/sec. At lower rolling speeds a very rapid change in the effective viscosity of the lubricant is predicted. This behavior, in conjunction with shear rate effects, is shown to lead to large errors when experimental data are extrapolated to zero rolling speed.

Enhancing roll stability of heavy vehicle by LQR active anti-roll bar control using electronic servo-valve hydraulic actuators

NASA Astrophysics Data System (ADS)

Vu, Van Tan; Sename, Olivier; Dugard, Luc; Gaspar, Peter

2017-09-01

Rollover of heavy vehicle is an important road safety problem world-wide. Although rollovers are relatively rare events, they are usually deadly accidents when they occur. The roll stability loss is the main cause of rollover accidents in which heavy vehicles are involved. In order to improve the roll stability, most of modern heavy vehicles are equipped with passive anti-roll bars to reduce roll motion during cornering or riding on uneven roads. However these may be not sufficient to overcome critical situations. This paper introduces the active anti-roll bars made of four electronic servo-valve hydraulic actuators, which are modelled and integrated in a yaw-roll model of a single unit heavy vehicle. The control signal is the current entering the electronic servo-valve and the output is the force generated by the hydraulic actuator. The active control design is achieved solving a linear optimal control problem based on the linear quadratic regulator (LQR) approach. A comparison of several LQR controllers is provided to allow for tackling the considered multi-objective problems. Simulation results in frequency and time domains show that the use of two active anti-roll bars (front and rear axles) drastically improves the roll stability of the single unit heavy vehicle compared with the passive anti-roll bar.

Multi-stage FE simulation of hot ring rolling

NASA Astrophysics Data System (ADS)

Wang, C.; Geijselaers, H. J. M.; van den Boogaard, A. H.

2013-05-01

As a unique and important member of the metal forming family, ring rolling provides a cost effective process route to manufacture seamless rings. Applications of ring rolling cover a wide range of products in aerospace, automotive and civil engineering industries [1]. Above the recrystallization temperature of the material, hot ring rolling begins with the upsetting of the billet cut from raw stock. Next a punch pierces the hot upset billet to form a hole through the billet. This billet, referred to as preform, is then rolled by the ring rolling mill. For an accurate simulation of hot ring rolling, it is crucial to include the deformations, stresses and strains from the upsetting and piercing process as initial conditions for the rolling stage. In this work, multi-stage FE simulations of hot ring rolling process were performed by mapping the local deformation state of the workpiece from one step to the next one. The simulations of upsetting and piercing stages were carried out by 2D axisymmetric models using adaptive remeshing and element erosion. The workpiece for the ring rolling stage was subsequently obtained after performing a 2D to 3D mapping. The commercial FE package LS-DYNA was used for the study and user defined subroutines were implemented to complete the control algorithm. The simulation results were analyzed and also compared with those from the single-stage FE model of hot ring rolling.

Finite-element model to predict roll-separation force and defects during rolling of U-10Mo alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Burkes, Douglas E.; Joshi, Vineet V.

This study used a finite element code, LSDYNA, as a predictive tool to optimize the rolling process. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel were conducted following two different schedules. Model predictions of the roll-separation force and roll pack thicknesses at different stages of the rolling process were compared with experimental measurements. The study reported here discussed various attributes of the rolled coupons revealed by the model (e.g., waviness and thickness non-uniformity like dog boning). To investigate the influence of the cladding material on these rolling defects, other cases were simulated:  hot rolling with alternative can materials, namely, 304 stainless steel and Zircaloy-2, and bare-rolling.

1. EXTERIOR VIEW OF BUILDING THAT HOUSES THE HOT ROLL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EXTERIOR VIEW OF BUILDING THAT HOUSES THE HOT ROLL MILL, ALSO KNOWN AS THE NO. 31 HOT ROLL MILL; LOOKING SOUTHWEST - American Brass Company, Kenosha Works, Hot Roll Mill, Kenosha, Kenosha County, WI

Increased compactibility of acetames after roll compaction.

PubMed

Kuntz, Theresia; Schubert, Martin A; Kleinebudde, Peter

2011-01-01

A common technique for manufacturing granules in a continuous way is the combination of roll compaction and subsequent milling. Roll compaction can considerably impact tableting performance of a material. The purpose of this study was to investigate the influence of roll compaction/dry granulation on the compaction behavior of acetames, a class of active pharmaceutical substances, which are mainly used for the treatment of central nervous diseases. Some representatives of acetames were roll compacted and then compressed into tablets. Compactibility of granules was compared with the compaction behavior of the directly compressed drug powders. In contrast to many other materials, the roll compaction step induced an increase in compactibility for all investigated acetames. Specific surface areas of the untreated and the roll compacted drugs were determined by nitrogen adsorption. The raise in compactibility observed was accompanied by an increase in specific surface area during roll compaction. Copyright © 2010 Elsevier B.V. All rights reserved.

Research and industrialization of near-net rolling technology used in shaft parts

NASA Astrophysics Data System (ADS)

Hu, Zhenghuan; Wang, Baoyu; Zheng, Zhenhua

2017-11-01

Shaft part rolling is an efficient and green nearnet shaping technology offering many advantages, including high production efficiency, high material utilization rate, high product quality, and excellent production environment. In this paper, the features of shaft part rolling are introduced along with the working principles of two main shaft part rolling technologies, namely, cross wedge rolling (CWR) and skew rolling (SR). In relation to this technology, some R&D achievements gained by the University of Science and Technology Beijing are summarized. Finally, the latest developments in shaft part rolling are presented, including SR steel balls, precise forming of camshaft blank by CWR, SR phosphorous copper balls at room temperature, and CWR hollow axle sleeve. Although the shaft part rolling technology has been widely used in China, it only accounts for about 15% of applicable parts at present. Nevertheless, this technology has broad application prospects.

Research and industrialization of near-net rolling technology used in shaft parts

NASA Astrophysics Data System (ADS)

Hu, Zhenghuan; Wang, Baoyu; Zheng, Zhenhua

2018-03-01

Shaft part rolling is an efficient and green nearnet shaping technology offering many advantages, including high production efficiency, high material utilization rate, high product quality, and excellent production environment. In this paper, the features of shaft part rolling are introduced along with the working principles of two main shaft part rolling technologies, namely, cross wedge rolling (CWR) and skew rolling (SR). In relation to this technology, some R&D achievements gained by the University of Science and Technology Beijing are summarized. Finally, the latest developments in shaft part rolling are presented, including SR steel balls, precise forming of camshaft blank by CWR, SR phosphorous copper balls at room temperature, and CWR hollow axle sleeve. Although the shaft part rolling technology has been widely used in China, it only accounts for about 15% of applicable parts at present. Nevertheless, this technology has broad application prospects.

Measurement method for roll angular displacement with a high resolution by using diffraction gratings and a heterodyne interferometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Shanzhi, E-mail: shanzhit@gmail.com; School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049; Wang, Zhao

The roll angle measurement is difficult to be achieved directly using a typical commercial interferometer due to its low sensitivity in axial direction, where the axial direction is orthogonal to the plane of the roll angular displacement. A roll angle measurement method combined diffraction gratings with a laser heterodyne interferometer is discussed in this paper. The diffraction grating placed in the plane of a roll angular displacement and the interferometer arranged in the plane's orthogonal direction, constitute the measurement pattern for the roll angle with high resolution. The roll angular displacement, considered as the linear, can be tested precisely whenmore » the corresponding angle is very small. Using the proposed method, the angle roll measurement obtains the high resolution of 0.002{sup ″}. Experiment has proved its feasibility and practicability.« less

75 FR 36363 - Procurement List: Proposed Additions and Deletions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-25

...-ply, 8'' x 350' rolls, white NSN: 8540-00-NIB-0061--Jumbo Roll Toilet Tissue, 1 ply, 3.7'' x 2000' NSN: 8540-00-NIB-0063--Jumbo Roll Toilet Tissue, 2 ply, 3.7'' x 1000' NSN: 8540-00-NIB-0007--Jumbo Roll Toilet Tissue, 2 ply, 3.7'' x 2000', 12'' dia. Roll NSN: 8540-00-NIB-0064--Center-Pull Paper Towel, 2-ply...

46 CFR 154.610 - Design temperature not colder than 0 °C (32 °F).

Code of Federal Regulations, 2010 CFR

2010-10-01

... materials must meet §§ 54.25-1 and 54.25-3 of this chapter. (b) Plates, forgings, rolled and forged bars and... batch of forgings, forged or rolled fittings, and forged or rolled bars and shapes. (f) The specified... ton batch of forgings, forged or rolled fittings and rolled or forged bars and shapes. (h) The...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Vineet V.; Paxton, Dean M.; Lavender, Curt A.

Over the past several years Pacific Northwest National Laboratory (PNNL) has been actively involved in supporting the U.S. Department of Energy National Nuclear Security Administration Office of Material Management and Minimization (formerly Global Threat Reduction Initiative). The U.S. High- Power Research Reactor (USHPRR) project is developing alternatives to existing highly enriched uranium alloy fuel to reduce the proliferation threat. One option for a high-density metal fuel is uranium alloyed with 10 wt% molybdenum (U-10Mo). Forming the U-10Mo fuel plates/foils via rolling is an effective technique and is actively being pursued as part of the baseline manufacturing process. The processing ofmore » these fuel plates requires systematic investigation/understanding of the pre- and post-rolling microstructure, end-state mechanical properties, residual stresses, and defects, their effect on the mill during processing, and eventually, their in-reactor performance. In the work documented herein, studies were conducted to determine the effect of cold and hot rolling the as-cast and homogenized U-10Mo on its microstructure and hardness. The samples were homogenized at 900°C for 48 h, then later annealed for several durations and temperatures to investigate the effect on the material’s microstructure and hardness. The rolling of the as-cast plate, both hot and cold, was observed to form a molybdenum-rich and -lean banded structure. The cold rolling was ineffective, and in some cases exacerbated the as-cast defects. The grains elongated along the rolling direction and formed a pancake shape, while the carbides fractured perpendicularly to the rolling direction and left porosity between fractured particles of UC. The subsequent annealing of these samples at sub-eutectoid temperatures led to rapid precipitation of the ' lamellar phase, mainly in the molybdenum-lean regions. Annealing the samples above the eutectoid temperature did not refine the grain size or the banded microstructure. However, annealing the samples led to quick recovery in hardness as evidenced by a drop in Vickers hardness of 20%. Hot rolling was performed at 650 and 800°C. The hot-rolling mill loads (load separation force) were approximately 40 to 50% less than the cold-rolling for the same reduction and thickness. It was observed that hot rolling the samples with 50% or more reduction in thickness were responsible for dynamic recrystallization in the hot-rolled samples and led to grain refinement. Unlike the cold-rolled samples, the hot-rolled samples did not fracture the carbides and appeared to heal the casting defects. The recovery phenomenon was similar to the cold-rolled samples above the eutectoid temperatures, but owing to the refined grain size, the precipitation of the lamellar phase was far more rapid in these samples and the hardness increased more rapidly than in the cold rolled sample when heated below the eutectoid temperature. The data generated from these rolling efforts has been used to make the process modeling efforts more robust and applicable to all USHPRR partner rolling mills. The flow stress for cold rolling the samples was determined to be between 170-190 ksi, with frictional forces between 0.2 and 0.4 for the PNNL mill. The measured roll separation forces and those simulated using finite element methods for hot and cold rolling for the PNNL rolling mill were in good agreement.« less

Assessment of flat rolling theories for the use in a model-based controller for high-precision rolling applications

NASA Astrophysics Data System (ADS)

Stockert, Sven; Wehr, Matthias; Lohmar, Johannes; Abel, Dirk; Hirt, Gerhard

2017-10-01

In the electrical and medical industries the trend towards further miniaturization of devices is accompanied by the demand for smaller manufacturing tolerances. Such industries use a plentitude of small and narrow cold rolled metal strips with high thickness accuracy. Conventional rolling mills can hardly achieve further improvement of these tolerances. However, a model-based controller in combination with an additional piezoelectric actuator for high dynamic roll adjustment is expected to enable the production of the required metal strips with a thickness tolerance of +/-1 µm. The model-based controller has to be based on a rolling theory which can describe the rolling process very accurately. Additionally, the required computing time has to be low in order to predict the rolling process in real-time. In this work, four rolling theories from literature with different levels of complexity are tested for their suitability for the predictive controller. Rolling theories of von Kármán, Siebel, Bland & Ford and Alexander are implemented in Matlab and afterwards transferred to the real-time computer used for the controller. The prediction accuracy of these theories is validated using rolling trials with different thickness reduction and a comparison to the calculated results. Furthermore, the required computing time on the real-time computer is measured. Adequate results according the prediction accuracy can be achieved with the rolling theories developed by Bland & Ford and Alexander. A comparison of the computing time of those two theories reveals that Alexander's theory exceeds the sample rate of 1 kHz of the real-time computer.

Comparative study on the corrosion behavior of the cold rolled and hot rolled low-alloy steels containing copper and antimony in flue gas desulfurization environment

NASA Astrophysics Data System (ADS)

Park, S. A.; Kim, J. G.; He, Y. S.; Shin, K. S.; Yoon, J. B.

2014-12-01

The correlation between the corrosion and microstructual characteristics of cold rolled and hot rolled low-alloy steels containing copper and antimony was established. The corrosion behavior of the specimens used in flue gas desulfurization systems was examined by electrochemical and weight loss measurements in an aggressive solution of 16.9 vol % H2SO4 + 0.35 vol % HCl at 60°C, pH 0.3. It has been shown that the corrosion rate of hot rolled steel is lower than that of cold rolled steel. The corrosion rate of cold rolled steel was increased by grain refinement, inclusion formation, and preferred grain orientation.

Digitalization in roll forming manufacturing

NASA Astrophysics Data System (ADS)

Sedlmaier, A.; Dietl, T.; Ferreira, P.

2017-09-01

Roll formed profiles are used in automotive chassis production as building blocks for the body-in-white. The ability to produce profiles with discontinuous cross sections, both in width and in depth, allows weight savings in the final automotive chassis through the use of load optimized cross sections. This has been the target of the 3D Roll Forming process. A machine concept is presented where a new forming concept for roll formed parts in combination with advanced robotics allowing freely positioned roll forming tooling in 3D space enables the production of complex shapes by roll forming. This is a step forward into the digitalization of roll forming manufacturing by making the process flexible and capable of rapid prototyping and production of small series of parts. Moreover, data collection in a large scale through the control system and integrated sensors lead to an increased understanding of the process and provide the basis to develop self-optimizing roll forming machines, increasing the productivity, quality and predictability of the roll-forming process. The first parts successfully manufactured with this new forming concept are presented.

Inflation with a smooth constant-roll to constant-roll era transition

NASA Astrophysics Data System (ADS)

Odintsov, S. D.; Oikonomou, V. K.

2017-07-01

In this paper, we study canonical scalar field models, with a varying second slow-roll parameter, that allow transitions between constant-roll eras. In the models with two constant-roll eras, it is possible to avoid fine-tunings in the initial conditions of the scalar field. We mainly focus on the stability of the resulting solutions, and we also investigate if these solutions are attractors of the cosmological system. We shall calculate the resulting scalar potential and, by using a numerical approach, we examine the stability and attractor properties of the solutions. As we show, the first constant-roll era is dynamically unstable towards linear perturbations, and the cosmological system is driven by the attractor solution to the final constant-roll era. As we demonstrate, it is possible to have a nearly scale-invariant power spectrum of primordial curvature perturbations in some cases; however, this is strongly model dependent and depends on the rate of the final constant-roll era. Finally, we present, in brief, the essential features of a model that allows oscillations between constant-roll eras.

Nanostructured Mg 2Ni materials prepared by cold rolling and used as negative electrode for Ni-MH batteries

NASA Astrophysics Data System (ADS)

Pedneault, Sylvain; Huot, Jacques; Roué, Lionel

In the present work, cold rolling has been investigated as a new means of producing Mg-based metal hydrides for nickel-metal hydride (Ni-MH) batteries. Structure and electrochemical evolution of 2Mg-Ni cold-rolled samples were investigated as a function of the number of rolling passes as well as heat treatment. It was found that nanocrystalline Mg 2Ni alloy can be obtained by an appropriate three step process involving rolling, heat treatment and rolling again. It was shown that the number of primary and secondary rolling passes must be carefully optimized in order to favour the complete formation of Mg 2Ni alloy having a nanocrystalline structure (∼10 nm in crystallite size) without excessive sample oxidation. Actually, the best result was obtained by first rolling 90 times, followed by a heat treatment at 400 °C for 4 h and roll again 20 times. The resulting material displayed an initial discharge capacity of 205 mAh g -1, which is quite similar to that obtained with ball-milled Mg 2Ni alloy.

40 CFR 467.21 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory § 467.21 Specialized definitions. For the purpose of this subpart: (a) The “core” of the rolling with emulsions subcategory shall include rolling using emulsions, roll grinding, stationary casting, homogenizing, artificial...

75 FR 50877 - Airworthiness Directives; Rolls-Royce plc RB211-524C2 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-18

... Airworthiness Directives; Rolls-Royce plc RB211-524C2 Series Turbofan Engines AGENCY: Federal Aviation.... The FAA amends Sec. 39.13 by adding the following new AD: 2010-17-13 Rolls-Royce plc (Formerly Rolls...) None. Applicability (c) This AD applies to Rolls-Royce plc (RR) model RB211-524C2-19 and RB211-524C2-B...

Development of a Dirigible Bomb

DTIC Science & Technology

1943-04-15

X - ¥ control for all future high-angle dirigible bombs in spite of the instrumental complications involved. /. two gyro system consisting of t...ts found thet the bomb wos in roll equilibrium £.t aero roll orientetion . Moreover, these roll equilibrium positions ire stt-ble ss indicated by...tirflow giving rise to voll torques in the seme direction fcs roll dis- placements from the «ero orientetion , the roll equilibrium found for equel pitch

A Review of Texture Evolution Mechanisms During Deformation by Rolling in Aluminum Alloys

NASA Astrophysics Data System (ADS)

Li, Shasha; Zhao, Qi; Liu, Zhiyi; Li, Fudong

2018-06-01

The current understanding of texture evolution during deformation by rolling in aluminum alloys was summarized. This included understanding the evolution mechanisms and several key factors of initial texture, microstructure, alloy composition, deformation temperature, stress-strain condition, and rolling geometry. Related models on predicting texture evolution during rolling were also discussed. Finally, for this research field, the recommendations for controlling the formation of rolling textures were proposed.

Advances in roll to roll processing of optics

NASA Astrophysics Data System (ADS)

Watts, Michael P. C.

2008-02-01

Today, there are a number of successful commercial applications that utilize roll to roll processing and almost all involve optics; unpatterned film, patterned film, and devices on film. The largest applications today are in holograms, and brightness enhancement film (BEF) for LCD. Solar cells are rapidly growing. These are mostly made in large captive facilities with their own proprietary equipment, materials and pattern generation capability. World wide roll to roll volume is > 100M meters2 year -1, and generates sales of > $5B. The vast majority of the sales are in BEF film by 3M.

Constant-roll tachyon inflation and observational constraints

NASA Astrophysics Data System (ADS)

Gao, Qing; Gong, Yungui; Fei, Qin

2018-05-01

For the constant-roll tachyon inflation, we derive the analytical expressions for the scalar and tensor power spectra, the scalar and tensor spectral tilts and the tensor to scalar ratio to the first order of epsilon1 by using the method of Bessel function approximation. The derived ns-r results are compared with the observations, we find that only the constant-roll inflation with ηH being a constant is consistent with the observations and observations constrain the constant-roll inflation to be slow-roll inflation. The tachyon potential is also reconstructed for the constant-roll inflation which is consistent with the observations.

Control law parameterization for an aeroelastic wind-tunnel model equipped with an active roll control system and comparison with experiment

NASA Technical Reports Server (NTRS)

Perry, Boyd, III; Dunn, H. J.; Sandford, Maynard C.

1988-01-01

Nominal roll control laws were designed, implemented, and tested on an aeroelastically-scaled free-to-roll wind-tunnel model of an advanced fighter configuration. The tests were performed in the NASA Langley Transonic Dynamics Tunnel. A parametric study of the nominal roll control system was conducted. This parametric study determined possible control system gain variations which yielded identical closed-loop stability (roll mode pole location) and identical roll response but different maximum control-surface deflections. Comparison of analytical predictions with wind-tunnel results was generally very good.

An advanced dissymmetric rolling model for online regulation

NASA Astrophysics Data System (ADS)

Cao, Trong-Son

2017-10-01

Roll-bite model is employed to predict the rolling force, torque as well as to estimate the forward slip for preset or online regulation at industrial rolling mills. The rolling process is often dissymmetric in terms of work-rolls rotation speeds and diameters as well as the friction conditions at upper and lower contact surfaces between work-rolls and the strip. The roll-bite model thus must be able to account for these dissymmetries and in the same time has to be accurate and fast enough for online applications. In the present study, a new method, namely Adapted Discretization Slab Method (ADSM) is proposed to obtain a robust roll-bite model, which can take into account the aforementioned dissymmetries and has a very short response time, lower than one millisecond. This model is based on the slab method, with an adaptive discretization and a global Newton-Raphson procedure to improve the convergence speed. The model was validated by comparing with other dissymmetric models proposed in the literature, as well as Finite Element simulations and industrial pilot trials. Furthermore, back-calculation tool was also constructed for friction management for both offline and online applications. With very short CPU time, the ADSM-based model is thus attractive for all online applications, both for cold and hot rolling.

Roll compaction/dry granulation: comparison between roll mill and oscillating granulator in dry granulation.

PubMed

Sakwanichol, Jarunee; Puttipipatkhachorn, Satit; Ingenerf, Gernot; Kleinebudde, Peter

2012-01-01

Different experimental factorial designs were employed to evaluate granule properties obtained from oscillating granulator and roll mill. Four oscillating-granulator parameters were varied, i.e. rotor speed, oscillating angle, aperture of mesh screen and rotor type. Six roll-mill parameters that were throughput, speed ratio in both first and second stages, gap between roll pair in both stages and roll-surface texture were also investigated. Afterwards, the granule properties obtained from two milling types with similar median particle size were compared. All milling parameters in both milling types affected significantly the median particle size, size distribution and amount of fine particles (P < 0.05), except the rotor types of oscillating granulator on fines. Only three milling parameters influenced significantly the flowability (P < 0.05). These were the throughput and the gap size in the first stage of roll mill and the sieve size of oscillating granulator. In comparison between milling types, the differences of granule properties were not practically relevant. However, the roll mill had much higher capacity than the oscillating granulator about seven times, resulting in improving energy savings per unit of product. Consequently, the roll mill can be applied instead of oscillating granulator for roll compaction/dry granulation technique.

The Effects of Forming Parameters on Conical Ring Rolling Process

PubMed Central

Meng, Wen; Zhao, Guoqun; Guan, Yanjin

2014-01-01

The plastic penetration condition and biting-in condition of a radial conical ring rolling process with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, were established. The reasonable value range of mandrel feed rate in rolling process was deduced. A coupled thermomechanical 3D FE model of RCRRCDS process was established. The changing laws of equivalent plastic strain (PEEQ) and temperature distributions with rolling time were investigated. The effects of ring's outer radius growth rate and rolls sizes on the uniformities of PEEQ and temperature distributions, average rolling force, and average rolling moment were studied. The results indicate that the PEEQ at the inner layer and outer layer of rolled ring are larger than that at the middle layer of ring; the temperatures at the “obtuse angle zone” of ring's cross-section are higher than those at “acute angle zone”; the temperature at the central part of ring is higher than that at the middle part of ring's outer surfaces. As the ring's outer radius growth rate increases at its reasonable value ranges, the uniformities of PEEQ and temperature distributions increase. Finally, the optimal values of the ring's outer radius growth rate and rolls sizes were obtained. PMID:25202716

Experimental determination of heat transfer coefficients in roll bite and air cooling for computer simulations of 1100 MPa carbon steel rolling

NASA Astrophysics Data System (ADS)

Leinonen, Olli; Ilmola, Joonas; Seppälä, Oskari; Pohjonen, Aarne; Paavola, Jussi; Koskenniska, Sami; Larkiola, Jari

2018-05-01

In modeling of hot rolling pass schedules the heat transfer phenomena have to be known. Radiation to ambient, between rolls and a steel slab as well as heat transfer in contacts must be considered to achieve accurate temperature distribution and thereby accurate material behavior in simulations. Additional heat is generated by friction between the slab and the work roll and by plastic deformation. These phenomena must be taken into account when the effective heat transfer coefficient is determined from experimental data. In this paper we determine the effective heat transfer coefficient at the contact interface and emissivity factor of slab surface for 1100MPa strength carbon steel for hot rolling simulations. Experimental pilot rolling test were carried out and slab temperatures gathered right below the interface and at the mid thickness of the slab. Emissivity factor tests were carried out in the same manner but without rolling. Experimental data is utilized to derive contact heat transfer coefficient at the interface and emissivity factor of slab surface. Pilot rolling test is reproduced in FE-analysis to further refine the heat transfer coefficient and emissivity factor. Material mechanical properties at rolling temperatures were determined by Gleeble™ thermo-mechanical simulator and IDS thermodynamic-kinetic-empirical software.

Micro-mechanisms of Surface Defects Induced on Aluminum Alloys during Plastic Deformation at Elevated Temperatures

NASA Astrophysics Data System (ADS)

Gali, Olufisayo A.

Near-surface deformed layers developed on aluminum alloys significantly influence the corrosion and tribological behavior as well as reduce the surface quality of the rolled aluminum. The evolution of the near-surface microstructures induced on magnesium containing aluminum alloys during thermomechanical processing has been investigated with the aim generating an understanding of the influence of individual forming parameters on its evolution and examine the microstructure of the roll coating induced on the mating steel roll through material transfer during rolling. The micro-mechanisms related to the various features of near-surface microstructure developed during tribological conditions of the simulated hot rolling process were identified. Thermomechanical processing experiments were performed with the aid of hot rolling (operating temperature: 550 to 460 °C, 4, 10 and 20 rolling pass schedules) and hot forming (operating temperature: 350 to 545 °C, strain rate: 4 x 10-2 s-1) tribo-simulators. The surface, near-surface features and material transfer induced during the elevated temperature plastic deformation were examined and characterized employing optical interferometry, SEM/EDS, FIB and TEM. Near-surface features characterized on the rolled aluminum alloys included; cracks, fractured intermetallic particles, aluminum nano-particles, oxide decorated grain boundaries, rolled-in oxides, shingles and blisters. These features were related to various individual rolling parameters which included, the work roll roughness, which induced the formation of shingles, rolling marks and were responsible for the redistribution of surface oxide and the enhancements of the depth of the near-surface damage. The enhanced stresses and strains experienced during rolling were related to the formation and propagation of cracks, the nanocrystalline structure of the near-surface layers and aluminum nano-particles. The mechanism of the evolution of the near-surface microstructure were determined to include grain boundary sliding which induced the cracks at the surface and subsurface of the alloy, magnesium diffusion to free surfaces, crack propagation from shear stresses and the shear strains inducing the nanocrystalline grain structure, the formation of shingles by the shear deformation of micro-wedges induced by the work roll grooves, and the deformation of this oxide covered micro-wedges inducing the rolled-in oxides. Magnesium diffusion to free surfaces was identified as inducing crack healing due to the formation of MgO within cracks and was responsible for the oxide decorated grain boundaries. An examination of the roll coating revealed a complex layered microstructure that was induced through tribo-chemical and mechanical entrapment mechanisms. The microstructure of the roll coating suggested that the work roll material and the rolled aluminum alloy were essential in determining its composition and structure. Subsequent hot forming processes revealed the rich oxide-layer of the near-surface microstructure was beneficial for reducing the coefficient of friction during tribological contact with the steel die. Damage to the microstructure include cracks induced from grain boundary sliding of near-surface grains and the formation of oxide fibres within cracks of the near-surface deformed layers.

Valuation of coefficient of rolling friction by the inclined plane method

NASA Astrophysics Data System (ADS)

Ciornei, F. C.; Alaci, S.; Ciogole, V. I.; Ciornei, M. C.

2017-05-01

A major objective of tribological researches is characterisation of rolling friction, due to various cases encountered in classical engineering applications, like gear transmissions and cam mechanisms or more recent examples met in bioengineering and biomedical devices. A characteristic of these examples consists in reduced dimensions of the contact zones, theoretically zero, the relative motion occurring between the contact points being either sliding or rolling. A characteristic parameter for the rolling motion is the coefficient of rolling friction. The paper proposes a method for estimation of coefficient of rolling friction by studying the motion of a body of revolution on an inclined plane. Assuming the hypothesis that moment of rolling friction is proportional to the normal reaction force, the law of motion for the body on the inclined plane is found under the premise of pure rolling. It is reached the conclusion that there is an uniformly accelerated motion, and thus for a known plane slope, it is sufficient to find the time during which the body runs a certain distance, starting from motionless situation. To obtain accurate results assumes finding precisely the time of motion. The coefficient of rolling friction was estimated for several slopes of the inclined plane and it is concluded that with increased slope, the values of coefficient of rolling friction increase, fact that suggest that the proportionality between the rolling torque and normal load is valid only for domains of limited variations of normal load.

40 CFR 426.30 - Applicability; description of the rolled glass manufacturing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rolled glass manufacturing subcategory. 426.30 Section 426.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Rolled Glass Manufacturing Subcategory § 426.30 Applicability; description of the rolled glass...

40 CFR 426.30 - Applicability; description of the rolled glass manufacturing subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rolled glass manufacturing subcategory. 426.30 Section 426.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Rolled Glass Manufacturing Subcategory § 426.30 Applicability; description of the rolled glass...

Spread prediction model of continuous steel tube based on BP neural network

NASA Astrophysics Data System (ADS)

Zhai, Jian-wei; Yu, Hui; Zou, Hai-bei; Wang, San-zhong; Liu, Li-gang

2017-07-01

According to the geometric pass of roll and technological parameters of three-roller continuous mandrel rolling mill in a factory, a finite element model is established to simulate the continuous rolling process of seamless steel tube, and the reliability of finite element model is verified by comparing with the simulation results and actual results of rolling force, wall thickness and outer diameter of the tube. The effect of roller reduction, roller rotation speed and blooming temperature on the spread rule is studied. Based on BP(Back Propagation) neural network technology, a spread prediction model of continuous rolling tube is established for training wall thickness coefficient and spread coefficient of the continuous rolling tube, and the rapid and accurate prediction of continuous rolling tube size is realized.

Effect of Cold-rolling on Mechanical Properties and Microstructure of an Al-12%Si-0.2%Mg Alloy

NASA Astrophysics Data System (ADS)

Liao, Hengcheng; Cai, Mingdong; Jing, Qiumin; Ding, Ke

2011-11-01

Effect of multi-pass cold-rolling on the mechanical properties and microstructure of a near-eutectic Al-12%Si-0.2%Mg casting alloy was investigated. Optical microscopy, SEM, and TEM were employed to resolve the as-rolled microstructure, and the microstructure of samples after aging treatment. It has been found that Brinell hardness increases considerably with rolling reduction ratio; and further annealing leads to a remarkable drop in hardness. Two mechanisms, namely precipitation hardening and recovery softening, were found to develop simultaneously in the subsequent aging treatment following cold rolling. In contrast, recovery softening dominated the aging of cold-rolled specimen with prior intermediate annealing. Tensile properties were also performed to measure the effect of cold rolling and subsequent aging treatment.

Research on the rolling moment in the symmetrical and asymmetrical rolling process

NASA Astrophysics Data System (ADS)

Alexa, V.; Raţiu, S. A.; Kiss, I.; Cioată, C. G.

2017-01-01

Research distribution the rolling moments symmetrical and asymmetrical report presents great importance both in theory and to introduce clarifications to the calculation of rolling resistance line assemblies. Clarifying individuals of metallic material deformation between the rolls single cylinder diameters act of any difference of work and analysis of advance and delay phenomena. Torque drive value for each of the rolling cylinders was done by reducing the thickness of the laminate samples, an experimental facility located in the laboratory of plastic deformation of the Faculty of Engineering Hunedoara. The analysis of research results show that in terms of power consumption for deformation and safety equipment in operation is rational for mills which require such a difference between the work rolls to execute about one cylinder operated.

The theory and technique of yamuna body rolling.

PubMed

Suzuki, Satoshi

2013-09-01

[Purpose] This paper provides information about the theory and technique of Yamuna Body Rolling. In order to treat physical problems, using the specialized Yamuna Body Rolling balls, people can target superficial skin, fasciae, muscle fibers, tendons, ligaments, bones, internal organs, and the nervous system by themselves. The extraordinary effect of Yamuna Body Rolling is its multidimensional elongation of muscle fibers. In addition to the regular longitudinal elongation by the conventional stretch method, Yamuna Body Rolling enables the transversal and diagonal expansion of muscle fibers in order to move the body more dynamically. Hamstring, abdominal, and sideline routines are presented as examples for techniques of Yamuna Body Rolling. Yamuna Body Rolling can be applied to functional evaluation and therapeutic uses; therefore, it could provide many benefits in the treatment of different conditions in the medical field.

Slow-roll approximation in loop quantum cosmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luc, Joanna; Mielczarek, Jakub, E-mail: joanna.luc@uj.edu.pl, E-mail: jakub.mielczarek@uj.edu.pl

The slow-roll approximation is an analytical approach to study dynamical properties of the inflationary universe. In this article, systematic construction of the slow-roll expansion for effective loop quantum cosmology is presented. The analysis is performed up to the fourth order in both slow-roll parameters and the parameter controlling the strength of deviation from the classical case. The expansion is performed for three types of the slow-roll parameters: Hubble slow-roll parameters, Hubble flow parameters and potential slow-roll parameters. An accuracy of the approximation is verified by comparison with the numerical phase space trajectories for the case with a massive potential term.more » The results obtained in this article may be helpful in the search for the subtle quantum gravitational effects with use of the cosmological data.« less

SEMI-ROLLED LEAF1 Encodes a Putative Glycosylphosphatidylinositol-Anchored Protein and Modulates Rice Leaf Rolling by Regulating the Formation of Bulliform Cells1[W][OA

PubMed Central

Xiang, Jing-Jing; Zhang, Guang-Heng; Qian, Qian; Xue, Hong-Wei

2012-01-01

Leaf rolling is an important agronomic trait in rice (Oryza sativa) breeding and moderate leaf rolling maintains the erectness of leaves and minimizes shadowing between leaves, leading to improved photosynthetic efficiency and grain yields. Although a few rolled-leaf mutants have been identified and some genes controlling leaf rolling have been isolated, the molecular mechanisms of leaf rolling still need to be elucidated. Here we report the isolation and characterization of SEMI-ROLLED LEAF1 (SRL1), a gene involved in the regulation of leaf rolling. Mutants srl1-1 (point mutation) and srl1-2 (transferred DNA insertion) exhibit adaxially rolled leaves due to the increased numbers of bulliform cells at the adaxial cell layers, which could be rescued by complementary expression of SRL1. SRL1 is expressed in various tissues and is expressed at low levels in bulliform cells. SRL1 protein is located at the plasma membrane and predicted to be a putative glycosylphosphatidylinositol-anchored protein. Moreover, analysis of the gene expression profile of cells that will become epidermal cells in wild type but probably bulliform cells in srl1-1 by laser-captured microdissection revealed that the expression of genes encoding vacuolar H+-ATPase (subunits A, B, C, and D) and H+-pyrophosphatase, which are increased during the formation of bulliform cells, were up-regulated in srl1-1. These results provide the transcript profile of rice leaf cells that will become bulliform cells and demonstrate that SRL1 regulates leaf rolling through inhibiting the formation of bulliform cells by negatively regulating the expression of genes encoding vacuolar H+-ATPase subunits and H+-pyrophosphatase, which will help to understand the mechanism regulating leaf rolling. PMID:22715111

Microstructure and texture evolution in cold-rolled and annealed alloy MA-956

NASA Astrophysics Data System (ADS)

Hosoda, Takashi

The microstructural and texture development with thermomechanical processing, performed through a combination of cold-rolling and annealing, in MA-956 plate consisting of a layered and inhomogeneous microstructure was systematically assessed. The alloy contained in mass percent, 20 Cr, 4.8 Al, 0.4 Ti, 0.4 Y2O3, and the balance iron. The starting material was as-hot-rolled plate, 9.7 mm thick. The as-hot-rolled plate was subjected to 40%, 60%, and 80% cold-rolling reduction and subsequently annealed at 1000, 1200, or 1380. Assessment of microstructural and texture developments before and after cold-rolling and annealing was performed using light optical microscopy (LOM), Vickers hardness testing, and electron backscatter diffraction (EBSD). Locally introduced misorientations by cold-rolling in each region were evaluated by Kernel Average Misorientation (KAM) maps. The as-hot-rolled condition contained a layered and inhomogeneous microstructure consisting of thin and coarse elongated grains, and aggregated regions which consisted of fine grains and sub-grains with {100} texture parallel to the longitudinal direction. The microstructure of the 40% cold-rolled condition contained deformation bands, and the 60% and 80% cold-rolled conditions also contained highly deformed regions where the deformation bands were intricately tangled. A predominant orientation of (001) parallel to the rolling direction was developed during cold-rolling, becoming more prominent with increasing reduction. The magnitudes of KAM angles varied through the thickness depending on the initial microstructures. Recrystallization occurred in regions where high KAM angles were dense after annealing and nucleation sites were the aggregation regions, deformation bands, and highly deformed regions. The shape and size of the recrystallized grains varied depending on the nucleation sites.

Effect of roll-compaction and milling conditions on granules and tablet properties.

PubMed

Perez-Gandarillas, Lucia; Perez-Gago, Ana; Mazor, Alon; Kleinebudde, Peter; Lecoq, Olivier; Michrafy, Abderrahim

2016-09-01

Dry granulation is an agglomeration process used to produce size-enlarged particles (granules), improving the handling properties of powders such as flowability. In this process, powders are compacted using a roll press to produce ribbons, which are milled in granules used further in the tableting process. The granule and tablet properties are influenced by the existence of different designs of the roll compactors, milling systems and the interaction between process parameters and raw material properties. The main objective of this work was to investigate how different roll-compaction conditions and milling process parameters impact on ribbons, granules and tablet properties, highlighting the role of the sealing system (cheek plates and rimmed roll). In this context, two common excipients differing in their mechanical behaviour (MCC and mannitol) are used. The study is based on the analysis of granule size distribution together with the characterization of loss of compactability during die compaction. Results show that the tensile strength of tablets is lower when using granules than when the raw materials are compressed. Moreover, the plastic material (MCC) is more sensitive than the brittle one (mannitol). Regarding the roll-force, it is observed that the higher the roll force, the lower the tensile strength of tablets from granulated material is. These findings are in agreement with the literature. The comparison of sealing systems shows that the rimmed-roll system leads to slightly stronger tablets than the use of cheek plates. In addition, the use of the rimmed-roll system reduces the amount of fines, in particular when high roll force is applied. Overall, it can be concluded that roll-compaction effect is predominant over the milling effect on the production of fines but less significant on the tablet properties. This study points out that the balance between a good flowability by reducing the amount of fines and appropriate tablet strength is achieved with rimmed-roll and the highest roll-force used. Copyright © 2016 Elsevier B.V. All rights reserved.

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE PAGES

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas; ...

2017-09-25

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Roll paper pilot. [mathematical model for predicting pilot rating of aircraft in roll task

NASA Technical Reports Server (NTRS)

Naylor, F. R.; Dillow, J. D.; Hannen, R. A.

1973-01-01

A mathematical model for predicting the pilot rating of an aircraft in a roll task is described. The model includes: (1) the lateral-directional aircraft equations of motion; (2) a stochastic gust model; (3) a pilot model with two free parameters; and (4) a pilot rating expression that is a function of rms roll angle and the pilot lead time constant. The pilot gain and lead time constant are selected to minimize the pilot rating expression. The pilot parameters are then adjusted to provide a 20% stability margin and the adjusted pilot parameters are used to compute a roll paper pilot rating of the aircraft/gust configuration. The roll paper pilot rating was computed for 25 aircraft/gust configurations. A range of actual ratings from 2 to 9 were encountered and the roll paper pilot ratings agree quite well with the actual ratings. In addition there is good correlation between predicted and measured rms roll angle.

Inflation with a constant rate of roll

NASA Astrophysics Data System (ADS)

Motohashi, Hayato; Starobinsky, Alexei A.; Yokoyama, Jun'ichi

2015-09-01

We consider an inflationary scenario where the rate of inflaton roll defined by ̈phi/H dot phi remains constant. The rate of roll is small for slow-roll inflation, while a generic rate of roll leads to the interesting case of 'constant-roll' inflation. We find a general exact solution for the inflaton potential required for such inflaton behaviour. In this model, due to non-slow evolution of background, the would-be decaying mode of linear scalar (curvature) perturbations may not be neglected. It can even grow for some values of the model parameter, while the other mode always remains constant. However, this always occurs for unstable solutions which are not attractors for the given potential. The most interesting particular cases of constant-roll inflation remaining viable with the most recent observational data are quadratic hilltop inflation (with cutoff) and natural inflation (with an additional negative cosmological constant). In these cases even-order slow-roll parameters approach non-negligible constants while the odd ones are asymptotically vanishing in the quasi-de Sitter regime.

Effect of differential speed rolling on the texture evolution of Mg-4Zn-1Gd alloy

NASA Astrophysics Data System (ADS)

Shim, Myeong-Shik; Suh, Byeong-Chan; Kim, Jae H.; Kim, Nack J.

2015-05-01

The microstructural and texture evolution during differential speed rolling process of Mg 4Zn-1Gd (wt%) alloy have been investigated by means of electron backscatter diffraction observation and texture analysis. The angular distribution of basal poles are inclined about 10° from the normal direction towards the rolling direction and the maximum intensities of basal poles are decreased, compared to the conventional rolling process. Such an inclination of angular distribution of basal poles can be induced by the operation of shear stress along the rolling direction, as much as one quarter of tensile stress along the RD and one quarter of compressive stress along the ND. When the reduction ratios in differential speed rolling increase, there is no difference in texture evolution although there is a significant change in activated twinning systems. In addition, the engineering stresses after differential speed rolling are also similar to that after conventional rolling process, while ductility and stretch formability in the former are worse than those in the latter.

Shearlet transform in aliased ground roll attenuation and its comparison with f-k filtering and curvelet transform

NASA Astrophysics Data System (ADS)

Abolfazl Hosseini, Seyed; Javaherian, Abdolrahim; Hassani, Hossien; Torabi, Siyavash; Sadri, Maryam

2015-06-01

Ground roll, which is a Rayleigh surface wave that exists in land seismic data, may mask reflections. Sometimes ground roll is spatially aliased. Attenuation of aliased ground roll is of importance in seismic data processing. Different methods have been developed to attenuate ground roll. The shearlet transform is a directional and multidimensional transform that generates subimages of an input image in different directions and scales. Events with different dips are separated in these subimages. In this study, the shearlet transform is used to attenuate the aliased ground roll. To do this, a shot record is divided into several segments, and the appropriate mute zone is defined for all segments. The shearlet transform is applied to each segment. The subimages related to the non-aliased and aliased ground roll are identified by plotting the energy distributions of subimages with visual checking. Then, muting filters are used on selected subimages. The inverse shearlet transform is applied to the filtered segment. This procedure is repeated for all segments. Finally, all filtered segments are merged using the Hanning window. This method of aliased ground roll attenuation was tested on a synthetic dataset and a field shot record from the west of Iran. The synthetic shot record included strong aliased ground roll, whereas the field shot record did not. To produce the strong aliased ground roll on the field shot record, the data were resampled in the offset direction from 30 to 60 m. To show the performance of the shearlet transform in attenuating the aliased ground roll, we compared the shearlet transform with the f-k filtering and curvelet transform. We showed that the performance of the shearlet transform in the aliased ground roll attenuation is better than that of the f-k filtering and curvelet transform in both the synthetic and field shot records. However, when the dip and frequency content of the aliased ground roll are the same as the reflections, ability of the shearlet transform is limited in attenuating the aliased ground roll.

Retinal vessel tortuosity measures and their applications.

PubMed

Kalitzeos, Angelos A; Lip, Gregory Y H; Heitmar, Rebekka

2013-01-01

Structural retinal vascular characteristics, such as vessel calibers, tortuosity and bifurcation angles are increasingly quantified in an objective manner, slowly replacing subjective qualitative disease classification schemes. This paper provides an overview of the current methodologies and calculations used to compute retinal vessel tortuosity. We set out the different parameter calculations and provide an insight into the clinical applications, while critically reviewing its pitfalls and shortcomings. Copyright © 2012 Elsevier Ltd. All rights reserved.

Recursive Gradient Estimation Using Splines for Navigation of Autonomous Vehicles.

DTIC Science & Technology

1985-07-01

AUTONOMOUS VEHICLES C. N. SHEN DTIC " JULY 1985 SEP 1 219 85 V US ARMY ARMAMENT RESEARCH AND DEVELOPMENT CENTER LARGE CALIBER WEAPON SYSTEMS LABORATORY I...GRADIENT ESTIMATION USING SPLINES FOR NAVIGATION OF AUTONOMOUS VEHICLES Final S. PERFORMING ORG. REPORT NUMBER 7. AUTHOR(q) 8. CONTRACT OR GRANT NUMBER...which require autonomous vehicles . Essential to these robotic vehicles is an adequate and efficient computer vision system. A potentially more

The Bauschinger and Hardening Effects on Residual Stresses in an Autofrettaged Thick-Walled Cylinder

DTIC Science & Technology

1984-06-01

8217Large Caliber Weapon3 Systems Labrra-ory 1ý’ NUBE OF PAGES Dover, 1.7)70 14 "NITOING AGENCY N XME: A ADDRF!SS(Ir -ditI.. fromI Controlling Office. IS...US ARMY AMCCOM COMMANDER ATTN: DRSMC-LC(D) 1 US ARMY TANK-AUTMV COMD DRSMC-LCE(D) I ATTN: DRSTA-RC DRSMC-LCM(D) ( BLDC 321) 1 WARREN, MI 48090 DRSMC-LCS

Counter Nuclear, Biological, and Chemical Operations, This document compliments JCS Pub 3-11

DTIC Science & Technology

2000-08-16

Successful German Chemical Attack The concept of creating a toxic gas cloud from chemical cylinders was credited to Fritz Haber of the Kaiser Wilhelm Physical...of considerations: The high caliber of German theoretical and experimental physicists like Otto Hahn, Paul Harteck, Werner Heisenberg, Fritz ...Institute of Berlin in late 1914. Owing to a shortage of artillery shells, Haber thought a chemical gas cloud would negate the enemy’s earthworks

Uniaxial Tensile Strength and Flaw Characterization of SiC-N

DTIC Science & Technology

2014-01-01

study has been largely limited to tiles less than 40 mm thick, especially versus small caliber threats (1, 3, 4). Research and production of ceramic... production of very large ceramic components. One issue that may occur in the production of large ceramic components is uneven powder packing during the...flaw is important because flaws originate from different stages during the production process. Flaws associated with the processing of the material

Experimental Design and Analysis of M1A1 Commander/Gunner Performance during CONOPS (Continuous Operations) Using the U-COFT (Unit Conduct of Fire Trainer)

DTIC Science & Technology

1989-09-01

gun b. 7.62-mm coax manchine gun c. Commander’s weapon station caliber .50 machine gun d. M250 grenade launchers 2. Ammunition Simulation a. 105-mm...7.62-mm machine gun f. M250 smoke grenades 3. Normal Mode Simulation a. Stabilized coax machine gun b. Stabilized main gun c. Commander’s weapon d

High Speed Metal Removal

DTIC Science & Technology

1982-10-01

AISI 1340, 4140 , 4340, and HF-1) which are commonly used in large caliber projectile manufacture were machined at...Tool Load Data for AISI 1340 "finishing" cuts Life-Line Data for AISI 4140 "roughing" cuts Tool Wear-Land Chart Data for AISI 4140 - "roughing...34 cuts; 570 Ceramic Coated Carbide Tool Wear-Land Chart Data for AISI 4140 - "roughing" cuts; G-10 Ceramic- Tool Wear-Land Chart Data for AISI 4140

USSR Report, Military Affairs, No. 1774.

DTIC Science & Technology

1983-06-13

sodden and one had to adapt to it. He also felt obliged to help his competition rival. This did not insult Moiseyev or 49 iniure his self - esteem . It...mark and enclosed m parentheses were not clear in the original but have been supplied as appropriate in context . Other unattributed parenthetical...Group, the Greater the Success"—A. Kravchenko 33 THE OFFICER’S PEDAGOGIC SKILL: EXPERIENCE, PROBLEMS, OPINIONS *"Psychological- Pedagogic Caliber

Test Operations Procedure (TOP) 03-2-504A Safety Evaluation of Small Arms and Medium Caliber Weapons

DTIC Science & Technology

2013-05-29

Assessment HHAR Health Hazard Assessment Report HERO Hazards of Electromagnetic Radiation to Ordnance in. inch J Joule km/hr kilometers per hour...help standardize testing and to specify tests commonly used to identify and assess safety hazards associated with the use of small arms. The...19b. TELEPHONE NUMBER (include area code) Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. Z39-18

Standardized UXO Technology Demonstration Site, Open Field Scoring Record No. 893

DTIC Science & Technology

2008-07-01

EM) AMOS metal detector is a linear multichannel sensor array consisting of a 2-meter-wide transmitter coil and 16 receiver coils, mounted on a...ferrous and nonferrous metals : Will detect ammunition components 20-mm caliber and over at depths of up to 0.4 meter and ammunition components 100...robust, all-terrain trailer (fig. 1). b. The AMOS detector unit consists of the following main components: (1) Lower sensor level (dimensions

Standardized UXO Technology Demonstration Site, Blind Grid Scoring Record No. 919

DTIC Science & Technology

2008-07-01

provided by demonstrator) a. The core component of the electromagnetic (EM) AMOS metal detector is a linear multichannel sensor array consisting of a...Attainable accuracy of depth (z) +0.3 m h. Detection performance for ferrous and nonferrous metals : Will detect ammunition components 20-mm caliber...2-meter-wide transmitter coil and 16 receiver coils, mounted on a robust, all-terrain trailer (fig. 1). b. The AMOS detector unit consists of the

Customer Overview of Pulsed Laser Heating for Evaluation of Gun Bore Materials

DTIC Science & Technology

2015-05-01

Technical Report ARWSB-TR-15003 Customer Overview of Pulsed Laser Heating for Evaluation of Gun Bore Materials Mark E. Todaro...SUBTITLE Customer Overview of Pulsed Laser Heating for Evaluation of Gun Bore Materials 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c...thermomechanical effects that occur at the bore of large and medium caliber guns during firing. Hence, PLH has been used not only to gain insight into the erosion

Safety and Suitability for Service Assessment Testing of Large Caliber Ammunition Greater Than 40MM

DTIC Science & Technology

2013-07-02

2 July 2013 2 Page Paragraph 9.2 Insensitive Munitions Assessment ........................................ 14 9.3 Munition Software System ...encounter during storage and transportation. 3.12 Weapon System . A weapon and those components required for its operation, comprising the aggregate of...Provide a positive indexing system on the cartridge case to ensure proper orientation of the case when it is loaded into the weapon. 6.9 Weapon

Passing It On: Fighting the Pushtun on Afghanistan’s Frontier

DTIC Science & Technology

2010-01-01

tribesman who preferred slashing weapons. The standard British handgun at the turn of the century was the Webley front-break revolver; however a wide...common annoyance, not done for military reasons but to secure a really stout material for stringing the family bed; and if as our friend runs...a locally-manufactured long- barreled , often highly-decorated, curved- stocked firearm of the Pathan. It is usually in excess of .50 caliber and

Solving Operational Models of Interdependent Infrastructure Systems

DTIC Science & Technology

2014-12-01

resilience, getting the biggest “reduction in bang ” for their buck. The most important part of those modeling efforts is the formulation of a mathematical...about the requirements of each system to the model of the other system through shared data. This type of algorithm simulates the dynamic...than just another big project. I found a true interest and excitement working with you both and consider you both the highest caliber faculty I have

Scanning and Measuring Device for Diagnostic of Barrel Bore

NASA Astrophysics Data System (ADS)

Marvan, Ales; Hajek, Josef; Vana, Jan; Dvorak, Radim; Drahansky, Martin; Jankovych, Robert; Skvarek, Jozef

The article discusses the design, mechanical design, electronics and software for robot diagnosis of barrels with caliber of 120 mm to 155 mm. This diagnostic device is intended primarily for experimental research and verification of appropriate methods and technologies for the diagnosis of the main bore guns. Article also discusses the design of sensors and software, the issue of data processing and image reconstruction obtained by scanning of the surface of the bore.

Paladin Integrated Management (PIM)

DTIC Science & Technology

2013-12-01

46:35 UNCLASSIFIED 4 Mission and Description The M109 Family of Vehicles (FOV) 155-millimeter / 39-caliber Self-Propelled Howitzer ( SPH ) provides...Teams, and Stryker Brigade Combat Teams. The M109 FOV Carrier Ammunition Tracked (CAT) provides armored ammunition supply support to the SPH ...fielded versions of the Army’s SPH and CAT. The Paladin Integrated Management (PIM) SPH and CAT will replace the M109A6 Paladin and M992A2 FAASV

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Burnside, Walter D.

1989-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameter is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Working Performance Analysis of Rolling Bearings Used in Mining Electric Excavator Crowd Reducer

NASA Astrophysics Data System (ADS)

Zhang, Y. H.; Hou, G.; Chen, G.; Liang, J. F.; Zheng, Y. M.

2017-12-01

Refer to the statistical load data of digging process, on the basis of simulation analysis of crowd reducer system dynamics, the working performance simulation analysis of rolling bearings used in crowd reducer of large mining electric excavator is completed. The contents of simulation analysis include analysis of internal load distribution, rolling elements contact stresses and rolling bearing fatigue life. The internal load characteristics of rolling elements in cylindrical roller bearings are obtained. The results of this study identified that all rolling bearings satisfy the requirements of contact strength and fatigue life. The rationality of bearings selection and arrangement is also verified.

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Ericksen, Kurt P.; Burnside, Walter D.

1990-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameters is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Recycling strategy of the end-of-life rolling stock in China

NASA Astrophysics Data System (ADS)

Guo, L.; Wang, X. W.; Lin, Y.; Shen, X. F.; Liu, Y. Q.

2018-03-01

China's high-speed railway industry is growing fast, the side effect is that plenty of rolling stock come to the end of life each year. However, there are not relevant standards nor regulations for the recycling of rolling stock in China, which causes pollution and a waste of resources. In this paper, the basic meaning and characteristics of the circular economy is reviewed and applied to the rolling stock industry. The recycling steps are elaborated in detail according to the characteristics of rolling stock. The result proves that circular economy has both the theoretical and practical meaning in the rolling stock recycling industry in China.

E-selectin ligand-1 controls circulating prostate cancer cell rolling/adhesion and metastasis

PubMed Central

Yasmin-Karim, Sayeda; King, Michael R.; Messing, Edward M.; Lee, Yi-Fen

2014-01-01

Circulating prostate cancer (PCa) cells preferentially roll and adhere on bone marrow vascular endothelial cells, where abundant E-selectin and stromal cell-derived factor 1 (SDF-1) are expressed, subsequently initiating a cascade of activation events that eventually lead to the development of metastases. To elucidate the roles of circulating PCa cells' rolling and adhesion behaviors in cancer metastases, we applied a dynamic cylindrical flow-based microchannel device that is coated with E-selectin and SDF-1, mimicking capillary endothelium. Using this device we captured a small fraction of rolling PCa cells. These rolling cells display higher static adhesion ability, more aggressive cancer phenotypes and stem-like properties. Importantly, mice received rolling PCa cells, but not floating PCa cells, developed cancer metastases. Genes coding for E-selectin ligands and genes associated with cancer stem cells and metastasis were elevated in rolling PCa cells. Knock down of E-selectin ligand 1(ESL-1), significantly impaired PCa cells' rolling capacity and reduced cancer aggressiveness. Moreover, ESL-1 activates RAS and MAP kinase signal cascade, consequently inducing the downstream targets. In summary, circulating PCa cells' rolling capacity contributes to PCa metastasis, and that is in part controlled by ESL-1. PMID:25301730

Influence of 10 % Cold Rolling Reduction on Ageing Behaviour of Hot Rolled Al-Cu-Si-Mn-Mg Alloy

NASA Astrophysics Data System (ADS)

Ghosh, S. K.

2014-10-01

In the current study, the effect of 10 % cold rolling on the different ageing phenomena of Al-Cu-Si-Mn-Mg alloy was investigated. Both hot rolled and cold rolled alloys were subjected to both natural and artificial ageing processes. Hardness was measured to understand the change in the mechanical property of the alloy before and after rolling and also during ageing processes. From microscopy, it was evident that the cold rolling and subsequent ageing provided the alloy with a structure in which CuAl2 precipitates were uniformly distributed. The alloy exhibited the peak hardness value of 92 VHN after 2 days of natural ageing, whereas the cold deformed (10 %) alloy exhibited the higher peak hardness value of 139 VHN after 3 days of natural ageing. Peak hardness of the alloy reached 94 VHN, when hot rolled alloy was subjected to ageing at 250 °C for 1 h, whereas 10 % cold rolling followed by ageing (100 °C, 15 min) demonstrated accelerated and elevated hardening. The ageing behaviours thus obtained permit the alloy to provide a range of desirable combinations of strength and ductility for high strength weight saving applications.