10 CFR 429.20 - Residential clothes washers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... washers, a water factor (WF) in gallons per cycle per cubic feet (gal/cycle/cu ft). [76 FR 12451, Mar. 7... randomly selected and tested to ensure that— (i) Any represented value of the water factor, the estimated annual operating cost, the energy or water consumption, or other measure of energy or water consumption...

76 FR 49237 - Energy Conservation Program: Test Procedures for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-09

...In this supplemental notice of proposed rulemaking (SNOPR), the U.S. Department of Energy (DOE) proposes to revise its test procedure for residential clothes washers established under the Energy Policy and Conservation Act (EPCA). DOE proposes to incorporate provisions of the International Electrotechnical Commission (IEC) Standard 62301, ``Household electrical appliances--Measurement of standby power'' (Second Edition). DOE also proposes to update the provisions for measuring active mode energy and water consumption.

10 CFR 431.152 - Definitions concerning commercial clothes washers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Definitions concerning commercial clothes washers. 431.152... clothes washers. Commercial clothes washer means a soft-mounted front-loading or soft-mounted top-loading clothes washer that— (1) Has a clothes container compartment that— (i) For horizontal-axis clothes washers...

76 FR 27952 - Airworthiness Directives; Eurocopter France Model EC 120B Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... perform a functional test of the cyclic control. (b) To request a different method of compliance or a... control friction device by replacing a certain thrust washer with two thrust washers. This proposed AD is prompted by an incident in which the pilot encountered a sudden restriction of the cyclic control movement...

AGARD Flight Test Instrumentation Series. Volume 12. Aircraft Flight Test Data Processing. A Review of the State of the Art

DTIC Science & Technology

1980-11-01

limitations of available sig-nal conditionis.g equipment best able to Withstand the working environment. a The effects on the results of the...for stability and ctrol while the second mstim (3A, 3, 3C, and 3D) ehms the effects for performace and propulsion. am===3313 UNZtS TUSt CASES Total...purpose of increasing their scientific and technical potential; - Recommending effective ways for the member nations to use their research and development

Bolt-Tension Sensor

NASA Technical Reports Server (NTRS)

Goldie, James H.; Bushko, Dariusz A.; Gerver, Michael J.

1995-01-01

In technique for measuring tensile force of bolt, specially fabricated magnetostrictive washer used as force transducer. Compact, portable inductive electronic sensor placed against washer to measure tension force. New system provides accurate, economical, and convenient way to measure bolt tension in field. Measurements on test assembly shows that tension can be measured to accuracy of about plus or minus 1 percent of load capacity of typical bolt.

Evaluation of cleaning and disinfection performance of automatic washer disinfectors machines in programs presenting different cycle times and temperatures.

PubMed

Bergo, Maria do Carmo Noronha Cominato

2006-01-01

Thermal washer-disinfectors represent a technology that brought about great advantages such as, establishment of protocols, standard operating procedures, reduction in occupational risk of a biological and environmental nature. The efficacy of the cleaning and disinfection obtained by automatic washer disinfectors machines in running programs with different times and temperatures determined by the different official agencies was validated according to recommendations from ISO Standards 15883-1/1999 and HTM2030 (NHS Estates, 1997) for the determining of the Minimum Lethality and DAL both theoretically and through the use with thermocouples. In order to determine the cleaning efficacy, the Soil Test, Biotrace Pro-tect and the Protein Test Kit were used. The procedure to verify the CFU count of viable microorganisms was performed before and after the thermal disinfection. This article shows that the results are in compliance with the ISO and HTM Standards. The validation steps confirmed the high efficacy level of the Medical Washer-Disinfectors. This protocol enabled the evaluation of the procedure based on evidence supported by scientific research, aiming at the support of the Supply Center multi-professional personnel with information and the possibility of developing further research.

An investigation of the decontamination of Siqveland matrix bands.

PubMed

Whitworth, C L; Davies, K; Palmer, N O A; Martin, M V

2007-02-24

This study investigated blood contamination of artificially and clinically contaminated Siqveland matrix bands and retainers. A modified version of the recognised Kastle-Meyer test for blood was used to compare the efficacy of enzymatic agents, a washer-disinfector and an instrument washer for pre-sterilisation cleaning of Siqveland matrix bands and retainers. Assembled Siqveland matrix bands were contaminated either artificially with horse blood or clinically during dental treatment. Contaminated assembled matrix bands and retainers were subjected to immersion in an enzymatic agent, automated processing in a washer-disinfector or instrument washer, or a combination of pre-soaking and automatic cleaning. Residual blood contamination from each band and retainer was measured and compared to the volume of blood recovered from an unprocessed control group of contaminated assembled matrix bands or retainers. Residual blood was recovered from every clinically contaminated assembled Siqveland matrix band and retainer. The volume of blood recovered from assembled Siqveland matrix bands ranged from 0.13-7.1 microl and from retainers, following removal of the matrix band, from 0.001-1.523 microl. The most effective method of pre-sterilisation cleaning for artificially contaminated assembled matrix bands was processing in the washer-disinfector. Conversely, the most effective method for cleaning clinically contaminated assembled matrix bands and retainers was pre-soaking in an enzymatic agent followed by a heavy-duty cycle in an instrument washer. It is not possible to clean assembled Siqveland matrix bands using any method currently available to dental practitioners. Matrix bands should be discarded after use on one patient. Once the band is removed, all detectable blood can be removed from the retainer by pre-soaking in an enzymatic detergent followed by processing in an instrument washer.

Light Optics for Optical Stochastic Cooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andorf, Matthew; Lebedev, Valeri; Piot, Philippe

2016-06-01

In Optical Stochastic Cooling (OSC) radiation generated by a particle in a "pickup" undulator is amplified and transported to a downstream "kicker" undulator where it interacts with the same particle which radiated it. Fermilab plans to carry out both passive (no optical amplifier) and active (optical amplifier) tests of OSC at the Integrable Optics Test Accelerator (IOTA) currently in construction*. The performace of the optical system is analyzed with simulations in Synchrotron Radiation Workshop (SRW) accounting for the specific temporal and spectral properties of undulator radiation and being augmented to include dispersion of lens material.

Positive contact, self retaining bearing seals

DOEpatents

Johnson, Bruce H.; Larsen, Lawrence E.; Welch, Edmund F.

1992-05-05

An ultra-low friction bearing including an inner race, an outer race, bearing elements engaged between the inner and outer races and a seal between the inner and outer races is disclosed. The seal includes first and second sealing washers. The first washer has an outer diameter greater than an inner diameter of the outer race and an inner diameter greater than the outer diameter of the inner race. The second washer has an inner diameter less than the outer diameter of the inner race and an outer diameter less than the inner diameter of the outer race. The first washer slidably engages the outer race, the second washer slidably engages the inner race and the washers overlap and slidably engage one another. One of the washers snap fits into its respective inner or outer race while the other washer engages a stepped surface of the other of the inner and outer races. The grooved and stepped surface are offset from one another in a longitudinal direction of the races such that the washers are conically loaded thus providing a seal between the inner and outer races sufficient to prevent lubricant and contaminating particles from passing therethrough. The washers are made from a non-metallic semi-flexible low-modulus material.

Unitized Nut-and-Washer Assembly

NASA Technical Reports Server (NTRS)

Rossi, P. J.

1986-01-01

Combination nut, washer, and lockwasher secures parts quickly without damaging metal finishes. Nut and lockwasher are captured by bent tabs of flat washer in this concept for unified fastener. Optional perforated tab on flat washer allows easy tagging and storage. Fastener intended for attaching leads and buses to studs on electronic equipment.

21 CFR 880.6991 - Medical washer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Medical washer. 880.6991 Section 880.6991 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6991 Medical washer. (a) Identification. A medical washer is a device that is intended for general...

21 CFR 880.6991 - Medical washer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Medical washer. 880.6991 Section 880.6991 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6991 Medical washer. (a) Identification. A medical washer is a device that is intended for general...

21 CFR 880.6991 - Medical washer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Medical washer. 880.6991 Section 880.6991 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6991 Medical washer. (a) Identification. A medical washer is a device that is intended for general...

21 CFR 880.6991 - Medical washer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Medical washer. 880.6991 Section 880.6991 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6991 Medical washer. (a) Identification. A medical washer is a device that is intended for general...

21 CFR 880.6991 - Medical washer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical washer. 880.6991 Section 880.6991 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES....6991 Medical washer. (a) Identification. A medical washer is a device that is intended for general...

21 CFR 880.6800 - Washers for body waste receptacles.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Washers for body waste receptacles. 880.6800 Section 880.6800 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Miscellaneous Devices § 880.6800 Washers for body waste receptacles. (a) Identification. A washer for body waste...

21 CFR 880.6800 - Washers for body waste receptacles.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Washers for body waste receptacles. 880.6800 Section 880.6800 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Miscellaneous Devices § 880.6800 Washers for body waste receptacles. (a) Identification. A washer for body waste...

21 CFR 880.6800 - Washers for body waste receptacles.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Washers for body waste receptacles. 880.6800 Section 880.6800 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Miscellaneous Devices § 880.6800 Washers for body waste receptacles. (a) Identification. A washer for body waste...

21 CFR 880.6800 - Washers for body waste receptacles.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Washers for body waste receptacles. 880.6800 Section 880.6800 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Miscellaneous Devices § 880.6800 Washers for body waste receptacles. (a) Identification. A washer for body waste...

21 CFR 880.6800 - Washers for body waste receptacles.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Washers for body waste receptacles. 880.6800... Miscellaneous Devices § 880.6800 Washers for body waste receptacles. (a) Identification. A washer for body waste receptacles is a device intended for medical purposes that is used to clean and sanitize a body waste...

76 FR 72722 - Helical Spring Lock Washers From China and Taiwan

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

... Spring Lock Washers From China and Taiwan Determination On the basis of the record \\1\\ developed in the... antidumping duty orders on helical spring lock washers from China and Taiwan would be likely to lead to... with respect to helical spring lock washers from Taiwan. Background The Commission instituted these...

Self-locking washer and method of use

DOEpatents

Vodila, James M.; Huyett, John D.

1991-01-01

A self-locking washer made of a flat elongated piece of material having a slot in one end of it. The washer is designed so that it can be placed underneath bolts or nuts which are already installed without completely removing the bolt or nut. A method of use of the self-locking washer is also disclosed.

Modeling of bleach plant washer mineral scale

Treesearch

Alan Rudie; Peter Hart

2004-01-01

One of the more common areas of mineral scale formation in bleach plants is on washer face wires and the extraction rings of diffusion washers. Whereas most scale problems can be understood as a mixing of two streams that increase the concentrations of anions and cations and exceed a solubility product, washer problems are often more difficult to understand. The...

16 CFR Appendix F2 to Part 305 - Compact Clothes Washers

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Compact Clothes Washers F2 Appendix F2 to... LABELING RULEâ) Pt. 305, App. F2 Appendix F2 to Part 305—Compact Clothes Washers Range Information “Compact” includes all household clothes washers with a tub capacity of less than 1.6 cu. ft. Capacity Range of...

16 CFR Appendix F1 to Part 305 - Standard Clothes Washers

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Standard Clothes Washers F1 Appendix F1 to... LABELING RULEâ) Pt. 305, App. F1 Appendix F1 to Part 305—Standard Clothes Washers Range Information “Standard” includes all household clothes washers with a tub capacity of 1.6 cu. ft. or more. Capacity Range...

Mounting improves heat-sink contact with beryllia washer

NASA Technical Reports Server (NTRS)

1966-01-01

To conduct heat away from electrical components that must be electrically insulated from a metal heat sink, a metal washer and a coil spring are placed between one end of the electrical component and the beryllia washer mounted on the heat sink. The thermal paths are formed by the component lead and base, the metal and beryllia washers, and the compressed spring.

76 FR 61343 - Certain Helical Spring Lock Washers From Taiwan and the People's Republic of China: Final Results...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-04

... bearing surface. The scope does not include internal or external tooth washers, nor does it include spring... are lock washers of carbon steel, of carbon alloy steel, or of stainless steel, heat-treated or non-heat-treated, plated or non-plated, with ends that are off-line. Lock washers are designed to: (1...

75 FR 29720 - Certain Helical Spring Lock Washers From the People's Republic of China: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-27

...) provide a hardened bearing surface. The scope does not include internal or external tooth washers, nor... helical spring lock washers of carbon steel, of carbon alloy steel, or of stainless steel, heat- treated or non-heat-treated, plated or non-plated, with ends that are off-line. Helical spring lock washers...

35. VIEW OF DUAL VENTURI GAS WASHER IN THE GAS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. VIEW OF DUAL VENTURI GAS WASHER IN THE GAS WASHER PUMP HOUSE LOOKING NORTHEAST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Construction of a Simple, Inexpensive Multiple Enzyme-Linked Immunosorbent Assay Microdilution Plate Washer

PubMed Central

Stobbs, L. W.

1990-01-01

In this paper, plans are given for the construction of an inexpensive enzyme-linked immunosorbent assay plate washer from readily available materials. The wash unit uses an intermittent wash cycle based on a wash manifold cycling over the microdilution plates for a predetermined time. Laboratory tests showed that the unit provided reliable, rapid washing of plates with tap water, with no detectable contamination between wells. Substrate absorbance values for test samples from machine-washed plates were equal to or greater than absorbance values for corresponding samples from plates washed manually by an accepted protocol, by using either enzyme-linked immunosorbent assay wash buffer or tap water. Images PMID:16348216

Impedance-Based Pre-Stress Monitoring of Rock Bolts Using a Piezoceramic-Based Smart Washer-A Feasibility Study.

PubMed

Wang, Bo; Huo, Linsheng; Chen, Dongdong; Li, Weijie; Song, Gangbing

2017-01-27

Pre-stress degradation or looseness of rock bolts in mining or tunnel engineering threatens the stability and reliability of the structures. In this paper, an innovative piezoelectric device named a "smart washer" with the impedance method is proposed with the aim of developing a real-time device to monitor the pre-stress level of rock bolts. The proposed method was verified through tests on a rock bolt specimen. By applying high-frequency sweep excitations (typically >30 kHz) to the smart washer that was installed on the rock bolt specimen, we observed that the variation in impedance signatures indicated the rock bolt pre-stress status. With the degradation of rock bolt pre-stress, the frequency in the dominating peak of the real part of the electrical impedance signature increased. To quantify the effectiveness of the proposed technique, a normalized root mean square deviation (RMSD) index was developed to evaluate the degradation level of the rock bolt pre-stress. The experimental results demonstrated that the normalized RMSD-based looseness index, which was computed from the impedance value detected by the "smart washer", increased with loss of the pre-stress of the rock bolt. Therefore, the proposed method can effectively detect the degradation of rock bolt pre-stress, as demonstrated by experiments.

10 CFR 431.152 - Definitions concerning commercial clothes washers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Definitions concerning commercial clothes washers. 431.152 Section 431.152 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Commercial Clothers Washers § 431.152 Definitions concerning commercial...

Cognitive restructuring and exposure with a compulsive washer: a test of reciprocal inhibition.

PubMed

Giles, T R

1982-09-01

Reciprocal inhibition was tested with a compulsive washer using the affect elicited by rational self-statements as the response competitor to anxiety. Three conditions, CS alone, CS plus irrational self-statements, and CS plus rational self-statements, were randomly and continuously repeated over six trials. The CS was presented both imaginally and in vivo. It was hypothesized: (1) that subjective anxiety in all conditions would substantially diminish by the experiment's end; (2) that the rational self-statement condition would reduce (inhibit) subjective anxiety to a significantly greater degree than the other two conditions; and (3) that significant anxiety reduction would occur only during the rational restructuring trials. All three hypotheses were supported by the results.

76 FR 57075 - Helical Spring Lock Washers From China and Taiwan

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 731-TA-624-625; Third Review] Helical Spring... duty orders on helical spring lock washers from China and Taiwan. AGENCY: United States International...) to determine whether revocation of the antidumping duty orders on helical spring lock washers from...

Reduction of Salmonella on alfalfa seeds using peroxyacetic acid and a commercial seed washer is as effective as treatment with 20 000 ppm of Ca(OCl)2.

PubMed

Buchholz, A; Matthews, K R

2010-10-01

The efficacy of a commercial seed washer and 1 and 3% peroxyacetic acid or 20 000 ppm calcium hypochlorite for reducing Salmonella on alfalfa seeds was investigated. Alfalfa seeds were inoculated with Salmonella Stanley to achieve c. 5 log CFU g(-1). Seeds were then treated with 1 or 3% peroxyacetic acid or 20 000 ppm calcium hypochlorite for 15 min in a commercial seed washer that uses air to enhance contact of the sanitizer with the seed. Experiments were also conducted using industry and laboratory methods. An c. 1-log reduction in number of Salm. Stanley was demonstrated regardless of the chemical treatment or method of treatment. Although this 1-log reduction was significant (P < 0.05), differences among the treatments were not significant. Treating the seed with 1 and 3% peroxyacetic acid resulted in similar Salm. Stanley reductions of 1.77 and 1.34 log, respectively, not being statistically significant (P > 0.05). These results suggest that under conditions tested, 1 or 3% peroxyacetic acid solutions are equally effective as 20 000 ppm of Ca(OCl)2 in the reduction of Salm. Stanley on alfalfa seed when used in conjunction with a commercial seed washer. A 1% peroxyacetic acid solution could potentially be used in place of 20 000 ppm of Ca(OCl)2 for treatment of seeds used for sprouting. The commercial seed washer did not enhance removal of Salm. Stanley from alfalfa seeds, but did facilitate removal of excess soil from seeds. © 2010 The Authors. Journal compilation © 2010 The Society for Applied Microbiology.

77 FR 9700 - Large Residential Washers From Korea and Mexico

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-17

...)] Large Residential Washers From Korea and Mexico Determinations On the basis of the record \\1\\ developed... reasonable indication that an industry is materially injured by reason of imports from Mexico of large... imports of large residential washers from Mexico. Accordingly, effective December 30, 2011, the Commission...

77 FR 51569 - Large Residential Washers From Korea and Mexico

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-24

...)] Large Residential Washers From Korea and Mexico Scheduling of the final phase of countervailing duty and... and Mexico of large residential washers, provided for in subheading 8450.20.00 of the Harmonized... and Mexico are being sold in the United States at less than fair value within the meaning of section...

76 FR 66613 - Airworthiness Directives; Eurocopter France (Eurocopter) Model EC225LP Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-27

... were missing. Further investigation has shown that some of the cup washers that need to be used in... cup washers that need to be used in installing the countersunk head screws, which attach the pilot's... is missing, the ASB specifies removing the affected seat, checking for cup washers, and performing...

75 FR 9159 - Certain Helical Spring Lock Washers from the People's Republic of China: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-01

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-822] Certain Helical Spring Lock... of the administrative review of the antidumping duty order on certain helical spring lock washers... September 30, 2008. See Certain Helical Spring Lock Washers from the People's Republic of China: Preliminary...

Comparison of Bioabsorbable Interference Screws Composed of Poly-l-lactic Acid and Hydroxyapatite (PLLA-HA) to WasherLoc Tibial Fixation in Patients After Anterior Cruciate Ligament Reconstruction of the Knee Joint.

PubMed

Patkowski, Mateusz; Królikowska, Aleksandra; Reichert, Paweł

2016-01-01

The reconstruction of the anterior cruciate ligament (ACL) of the knee joint is a standard in ACL complete rupture treatment in athletes. One of the weakest points of this procedure is tibial fixation of grafts. The aim was, firstly, to evaluate patients 3-4 years after primary ACL reconstruction with the use of autologous ipsilateral STGR grafts and with tibial fixation using a bioabsorbable interference screw composed of PLLA-HA or WasherLoc, comparing the postoperative result to the preoperative condition and, secondly, to compare the results between the two groups of patients with different tibial fixation. Group I consisted of 20 patients with a bioabsorbable interference screw composed of PLLA-HA tibial fixation. In Group II, there were 22 patients after ACL reconstruction with the use of WasherLoc tibial fixation. The Lachman test, pivot-shift test, Lysholm Knee Scoring Scale and 2000 International Knee Documentation Committee (2000 IKDC) Subjective Knee Evaluation Form were used to evaluate the results. The intra-group comparison of the results of the 2000 IKDC Subjective Knee Evaluation Form and Lysholm Knee Scoring Scale obtained in the groups studied showed statistically significant differences between the evaluation performed preoperatively and postoperatively. The inter-group comparison of the results of the 2000 IKDC Subjective Knee Evaluation Form and Lysholm Knee Scoring Scale obtained postoperatively showed no statistically significant differences between the two groups. An evaluation 3-4 years after ACL reconstruction with the use of autologous ipsilateral STGR grafts demonstrated significant progress from the preoperative condition to the postoperative result in patients with tibial fixation using a bioabsorbable interference screw composed of PLLA-HA as well as in patients with WasherLoc tibial fixation. There were no differences found between the two groups of patients after ACL reconstruction in terms of manual stability testing or a subjective assessment of knee joint outcomes.

Hypersensitivity Pneumonitis

MedlinePlus

... breed animals or birds, cheese washers, woodworkers, and wine makers—have a greater chance of exposure to ... this test, talk to your doctor about the benefits and possible risks of this procedure. Lung biopsies ...

75 FR 17884 - Airworthiness Directives; Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-08

... product. The MCAI describes the unsafe condition as: Following five reported cases of balance washer screw...-conformity that increased their susceptibility to brittle fracture. Failure of a balance washer screw can result in loss of the related balance washer, with consequent turbine imbalance. Such imbalance could...

75 FR 30740 - Airworthiness Directives; Bombardier, Inc. Model CL-600-2B16 (CL-604 Variants (Including CL-605...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-02

... product. The MCAI describes the unsafe condition as: Following five reported cases of balance washer screw...-conformity that increased their susceptibility to brittle fracture. Failure of a balance washer screw can result in loss of the related balance washer, with consequent turbine imbalance. Such imbalance could...

Endoscope disinfection and its pitfalls--requirement for retrograde surveillance cultures.

PubMed

Buss, A J; Been, M H; Borgers, R P; Stokroos, I; Melchers, W J; Peters, F T; Limburg, A J; Degener, J E

2008-04-01

Several endoscopy-related outbreaks of infection have been reported in recent years. For early recognition of inadequate disinfection of endoscopes we designed a microbiological surveillance system to evaluate the efficacy of the cleaning and disinfection procedure, and to trace disinfection problems to individual endoscopes or washer-disinfectors. Our surveillance protocol included anterograde and retrograde sampling, a decision algorithm, genetic fingerprinting, and scanning electron microscopy. Over a period of 29 months we found an increasing number of patient-ready endoscopes testing positive for Candida species other than albicans, especially C. parapsilosis. These yeasts were also isolated from the washer-disinfectors. The number of positive tests for Candida species varied from 1 out of 21 to 14 out of 27 samples from nine frequently used endoscopes. The number of colony-forming units per milliliter ranged from 1 - 10 to 3000 for endoscopes and 0.002 to 0.06 for the washer disinfectors. DNA fingerprinting was not able to discriminate different strains within C. parapsilosis. Our protocol was able to detect a structural problem in the endoscope disinfection process. Retrograde sampling was crucial for this purpose, because it has much higher sensitivity than anterograde sampling. Endoscopes with damaged working channels are probably the source of the contamination problem with Candida species.

Windshield washer fluid

MedlinePlus

... tests Chest x-ray CT (computerized tomography, or advanced imaging) scan EKG (electrocardiogram, or heart tracing) Fluids ... Stanton BF, St. Geme JW, Schor NF, eds. Nelson Textbook of Pediatrics . 20th ed. Philadelphia, PA: Elsevier; ...

76 FR 75873 - Certain Helical Spring Lock Washers From Taiwan and the People's Republic of China: Continuation...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

... or bolts; and (3) provide a hardened bearing surface. The scope does not include internal or external tooth washers, nor does it include spring lock washers made of other metals, such as copper. Lock..., or of stainless steel, heat-treated or non-heat-treated, plated or non-plated, with ends that are off...

Characteristics of Infrared Detectors for Spece Applications

DTIC Science & Technology

2000-10-01

using Platinium Resistance Thermometers using the four lead method. The readout is performed by a high performace voltmeter, HP 3458 type. These...3.3.4 Temperature measurements The accuracy of the temperature measurements are mainly due to the Platinium Resistance Thermometers using the four lead

Rock bolt overload warning device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unrug, K.F.

1983-10-18

A washer is described which is used in the construction of the support for the roof of a mine. The washer is fabricated such that finger like projections rupture in stages as the tension on bolts and pressure in the strata of the roof of the mine increases beyond structurely safe limits. The rupturing of the washer emits audible warning signals and also provides a visual indication of an unsafe condition.

Adjustable-Torque Truss-Joint Mechanism

NASA Technical Reports Server (NTRS)

Bush, Harold G.; Wallsom, Richard E.

1993-01-01

Threaded pin tightened or loosened; tedious trial-and-error procedure shortened. Mechanism joining strut and node in truss structure preloaded to desired stress to ensure tight, compressive fit preventing motion of strut during loading or vibration. Preload stress on stack of Belleville spring washers adjusted by tightening or loosening threaded Belleville-washer-alignment pin. Pin turned, by use of allen wrench, to adjust compression preload on Belleville washers and adjusts joint-operating torque.

Magnetic charges suppress effects of anisotropy in polycrystalline soft ferromagnetic materials

NASA Astrophysics Data System (ADS)

Arrott, Anthony S.; Williams, Conrad M.; Negusse, Ezana

2018-05-01

Micromagnetic simulations of polycrystalline iron washers show that grain boundary charges, ρ = -div M, suppress bad effects of magnetocrystalline anisotropy. A single domain wall divides the washer into two domains with opposite magnetization; M is almost = ± Ms ϕ, where ϕ circulates about the hole in the washer. There is a ripple structure. M tilts back and forth toward the inner and outer surfaces. Magnetic charge densities, σm = n.M, on the surfaces keep M at the surfaces very close to lying in the surfaces. The exchange ɛx and magnetostatic ɛd energy densities try to keep M parallel to the surfaces throughout the washer, except at the domain wall. An anisotropy energy in each grain is reduced linearly in the angle of rotation away from the circulating pattern towards the nearest anisotropy axis. Both ɛx and ɛd near grain boundaries increase as the square of these angles. Anisotropy wins for small rotations. However, the coefficients of the positive quadratic terms are so much larger than the coefficients of the negative linear terms that the rotations are quite small. If the height of the washer is sufficiently greater than 300 nm, M in the washer no longer acts as it would in a thin film. If 300 nm washers are stacked with a spacing of 4 nm, the ripple structure is not lost. The stacked washers can then be used as the core of a transformer. The most remarkable effect is that starting with M = Ms ϕ everywhere, the reversal of M by the field from a current along the z-axis produces a single domain wall. It is stable even in zero field because the wall has Néel caps that act as springs against the surfaces. The suppression of crystalline anisotropy in polycrystalline iron also occurs for geometries other than the toroid; some might be better for creating transformers.

77 FR 48108 - Energy Conservation Standards for Commercial Clothes Washers: Public Meeting and Availability of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-13

... written comments on potential amended standards, including comments on the issues identified in the... Legal Authority II. Test Procedures III. Energy Conservation Standards I. Introduction and Legal... the date of publication of the final standards. II. Test Procedures EPCA requires that CCWs use the...

40 CFR 60.287a - Recordkeeping.

Code of Federal Regulations, 2014 CFR

2014-07-01

... furnace, digester system, brown stock washer system, multiple-effect evaporator system, or condensate... digester system, brown stock washer system, multiple effect evaporator system, or condensate stripper...

Clothes washer standards in China -- The problem of water andenergy trade-offs in establishing efficiency standards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biermayer, Peter J.; Lin, Jiang

2004-05-19

Currently the sales of clothes washers in China consist ofseveral general varieties. Some use more energy (with or withoutincluding hot water energy use) and some use more water. Both energy andwater are in short supply in China. This poses the question - how do youtrade off water versus energy in establishing efficiency standards? Thispaper discusses how China dealt with this situation and how itestablished minimum efficiency standards for clothes washers.

Eddy-Current Detection of Weak Bolt Heads

NASA Technical Reports Server (NTRS)

Messina, C. P.

1987-01-01

Electronic test identifies flawed units passing hardness tests. Eddy-current test detects weakness in head-to-shank junctions of 1/4-28 cup-washer lock bolts. Developed for alloy A286 steel bolts in Space Shuttle main engine fuel turbo-pump. Test examines full volume of head, including head-to-shank transition and nondestructively screens out potentially defective units. Test adapts to any other alloys.

Device for measuring hole elongation in a bolted joint

NASA Technical Reports Server (NTRS)

Wichorek, Gregory R. (Inventor)

1987-01-01

A device to determine the operable failure mode of mechanically fastened lightweight composite joints by measuring the hole elongation of a bolted joint is disclosed. The double-lap joint test apparatus comprises a stud, a test specimen having a hole, two load transfer plates, and linear displacement measuring instruments. The test specimen is sandwiched between the two load transfer plates and clamped together with the stud. Spacer washers are placed between the test specimen and each load transfer plate to provide a known, controllable area for the determination of clamping forces around the hole of the specimen attributable to bolt torque. The spacer washers also provide a gap for the mounting of reference angles on each side of the test specimen. Under tensile loading, elongation of the hole of the test specimen causes the stud to move away from the reference angles. This displacement is measured by the voltage output of two linear displacement measuring instruments that are attached to the stud and remain in contact with the reference angles throughout the tensile loading. The present invention obviates previous problems in obtaining specimen deformation measurements by monitoring the reference angles to the test specimen and the linear displacement measuring instruments to the stud.

75 FR 57915 - Energy Conservation Program for Consumer Products: Notice of Petition for Waiver of the General...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-23

... Than Automobiles.'' (42 U.S.C. 6291-6309). Part A includes definitions, test procedures, labeling... marketer of household appliances, including, as relevant to this proceeding, clothes washers, files this...

SOUTH WING, MTR661. INTERIOR DETAIL INSIDE LAB ROOM 131. CAMERA ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTH WING, MTR-661. INTERIOR DETAIL INSIDE LAB ROOM 131. CAMERA FACING NORTHEAST. NOTE CONCRETE BLOCK WALLS. SAFETY SHOWER AND EYE WASHER AT REAR WALL. INL NEGATIVE NO. HD46-7-2. Mike Crane, Photographer, 2/2005. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

24 CFR 3280.809 - Grounding.

Code of Federal Regulations, 2014 CFR

2014-04-01

... and approved as pressure-terminal connectors recognized for the wire size used. Star washers or other... as screws and star washers or equivalent). [40 FR 58752, Dec. 18, 1975. Redesignated at 44 FR 20679...

24 CFR 3280.809 - Grounding.

Code of Federal Regulations, 2011 CFR

2011-04-01

... and approved as pressure-terminal connectors recognized for the wire size used. Star washers or other... as screws and star washers or equivalent). [40 FR 58752, Dec. 18, 1975. Redesignated at 44 FR 20679...

24 CFR 3280.809 - Grounding.

Code of Federal Regulations, 2012 CFR

2012-04-01

... and approved as pressure-terminal connectors recognized for the wire size used. Star washers or other... as screws and star washers or equivalent). [40 FR 58752, Dec. 18, 1975. Redesignated at 44 FR 20679...

24 CFR 3280.809 - Grounding.

Code of Federal Regulations, 2013 CFR

2013-04-01

... and approved as pressure-terminal connectors recognized for the wire size used. Star washers or other... as screws and star washers or equivalent). [40 FR 58752, Dec. 18, 1975. Redesignated at 44 FR 20679...

10 CFR Appendix J to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2010 CFR

2010-01-01

...'s true energy consumption characteristics as to provide materially inaccurate comparative data... clothes washers should be totally representative of the design, construction, and control system that will...

10 CFR Appendix J to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2012 CFR

2012-01-01

...'s true energy consumption characteristics as to provide materially inaccurate comparative data... clothes washers should be totally representative of the design, construction, and control system that will...

10 CFR Appendix J to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2011 CFR

2011-01-01

...'s true energy consumption characteristics as to provide materially inaccurate comparative data... clothes washers should be totally representative of the design, construction, and control system that will...

Choosing a Type 2 Diabetes Drug: Why Generic Metformin is Often the Best Choice

MedlinePlus

... Mattresses Pressure Washers Smoke & CO Detectors String Trimmers Toilets Water Filters Windows All Home & Garden More on ... the-Range Microwaves From Consumer Reports' Tests Save space on the counter with a mounted microwave that ...

78 FR 1570 - Semiannual Regulatory Agenda

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-08

... Transformers (energy efficiency standards) Residential clothes washers (energy efficiency standards... Distribution Transformers (Reg Plan Seq No. 32). 263 Test Procedures for 1904-AC76 Residential Refrigerators... Efficiency Standards for Distribution Transformers Regulatory Plan: This entry is Seq. No. 32 in part II of...

Compact thermoelectric converter systems technology

NASA Technical Reports Server (NTRS)

1973-01-01

A schematic of the developed tubular thermoelectric module is shown. It consists of alternate washers of n- and p-type lead telluride, separated by thin natural mica washers. Electrical continuity within the circuit is accomplished by cylindrical conductor rings located at the I.D. and O.D. of the lead telluride washers. The conductor rings are also separated by the same mica which separate the lead telluride washers. The result is a radially serpentine current path along the length of the module. The circuit is isolated from the structural claddings by thin sleeves of boron nitride. Circuit containment and heat transfer surfaces are provided by the inner and outer cladding, heat being transferred from a heat source at the inner clad, conducted radially outward through the lead telluride to the outer clad where the waste heat is removed by a heat rejection system.

ESGE-ESGENA technical specification for process validation and routine testing of endoscope reprocessing in washer-disinfectors according to EN ISO 15883, parts 1, 4, and ISO/TS 15883-5.

PubMed

Beilenhoff, Ulrike; Biering, Holger; Blum, Reinhard; Brljak, Jadranka; Cimbro, Monica; Dumonceau, Jean-Marc; Hassan, Cesare; Jung, Michael; Neumann, Christiane; Pietsch, Michael; Pineau, Lionel; Ponchon, Thierry; Rejchrt, Stanislav; Rey, Jean-François; Schmidt, Verona; Tillett, Jayne; van Hooft, Jeanin

2017-12-01

1 Prerequisites. The clinical service provider should obtain confirmation from the endoscope washer-disinfector (EWD) manufacturer that all endoscopes intended to be used can be reprocessed in the EWD. 2 Installation qualification. This can be performed by different parties but national guidelines should define who has the responsibilities, taking into account legal requirements. 3 Operational qualification. This should include parametric tests to verify that the EWD is working according to its specifications. 4 Performance qualification. Testing of cleaning performance, microbiological testing of routinely used endoscopes, and the quality of the final rinse water should be considered in all local guidelines. The extent of these tests depends on local requirements. According to the results of type testing performed during EWD development, other parameters can be tested if local regulatory authorities accept this. Chemical residues on endoscope surfaces should be searched for, if acceptable test methods are available. 5 Routine inspections. National guidelines should consider both technical and performance criteria. Individual risk analyses performed in the validation and requalification processes are helpful for defining appropriate test frequencies for routine inspections. © Georg Thieme Verlag KG Stuttgart · New York.

Can Standards Increase Consumer Welfare? Evidence from a Change in Clothes Washer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiaomei; Roberts, Michael J.; Yang, Hung-Chia

We study prices and sales of individual clothes washer models before, during and after a 2007 standard that banned manufacture (but not sale) of low-e ciency units and increased the threshold for Energy Star certi cation. While quantities sold of washer models banned from manufacture decreased sharply, prices for banned models increased only modestly. At the same time, sales of higher-e ciency units rose markedly while prices for high-e ciency units declined. On average, washer e ciency increased but prices changed little. A simple welfare analysis indicates that consumer welfare loss from banned washers was far outweighed by gains frommore » lower-priced high-e ciency units. While a full cost-bene t analysis is not feasible with the available data, we estimate a lower-bound gain in consumer surplus equal to 6-16 percent of total sales. This result may accord with earlier theoretical research that shows quality standards can increase welfare in monopolistically competitive industries that possess increasing returns to scale (Ronnen, 1991). Thus, if energy e ciency is a close proxy for quality, energy e ciency standards may increase competition, market e ciency and welfare.« less

EH 11n modes E type in the disk and washer accelerating structure

NASA Astrophysics Data System (ADS)

Andreev, V. G.; Belugin, V. M.; Daikovsky, A. G.; Esin, S. K.; Kravchuk, L. V.; Paramonov, V. V.; Ryabov, A. D.

1983-01-01

The disk and washer accelerating structure has a great deal to do with high-beta structures progress. The frequencies and electromagnetic fields for modes, which have a different number of azimuthal variations, are calculated to determined the dispersion properties and other characteristics of parasitic modes in a disc and washer accelerating structure. The main attention was given to the accelerating structure of the linear accelerator of the Institute for Nuclear Research (INR) of the USSR Academy of Sciences. Modification of a structure for PIGMI accelerator (LANL, USA) is considered briefly.

Preliminary engineering analysis for clothes washers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biermayer, Peter J.

1996-10-01

The Engineering Analysis provides information on efficiencies, manufacturer costs, and other characteristics of the appliance class being analyzed. For clothes washers, there are two classes: standard and compact. Since data were not available to analyze the compact class, only clothes washers were analyzed in this report. For this analysis, individual design options were combined and ordered in a manner that resulted in the lowest cumulative cost/savings ratio. The cost/savings ratio is the increase in manufacturer cost for a design option divided by the reduction in operating costs due to fuel and water savings.

DESIGN AND PROTOTYPE OF A SUSTAINABLE EGG-WASHER

EPA Science Inventory

This project is part of the senior design course for Engineering Science and Mechanics at Virginia Tech. Anticipated results will be a working prototype chosen from multiple designs. We will include test results supporting our selection. We will characterize the stresses ex...

23. VIEW OF 'PROCECO' WHEEL WASHER (uses spaulk and hot ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. VIEW OF 'PROCECO' WHEEL WASHER (uses spaulk and hot alkaline solution), Don N. Calabese, operator. - Juniata Shops, Erecting Shop & Machine Shop, East of Fourth Avenue, between Fourth & Fifth Streets, Altoona, Blair County, PA

10 CFR Appendix J1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2014 CFR

2014-01-01

... clothes washer design can achieve spin speeds in the 500g range. When this matrix is repeated 3 times, a...) or an equivalent extractor with same basket design (i.e. diameter, length, volume, and hole... materially inaccurate comparative data, field testing may be appropriate for establishing an acceptable test...

The corrosion effect of ozonated seawater solution on titanium in polymer generated crevice environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leveillee, S.Y.

1998-01-01

Two different tests were designed to evaluate the reaction of various polymers and grade-2 titanium in ozonated seawater in conjunction with a comparative analysis in an aerated seawater solution. The first was a weight loss test measuring the weight change of Polyvinyl chloride (PVC), Polyethylene and Teflon{trademark} in both ozonated and aerated artificial seawater baths. The second test was designed to induce crevice corrosion on the titanium test samples using various crevice generating materials in both ozonated and aerated solutions. The materials used to create the crevices were grade-2 titanium washers, PVC, Polyethylene, Saran and Teflon{trademark}. The weight loss testmore » showed that all three polymers lost weight in the ozonated bath. The results of the titanium washer crevice test provided no indication of corrosion or surface discoloration in either the ozonated or aerated solutions. Energy dispersive spectrometry (EDS) analysis found no fluorine, chlorine or other corrosion product. The PVC samples in the aerated bath also showed no signs of corrosion, but the PVC samples in the ozonated tank had light brown rings of surface discoloration. One of the ozonated PVC samples did show evidence of chlorine in the corrosion product. The outer circumference of the ozonated PVC washers exhibited the same type bleaching effect as in the weight loss samples, but the whitening of these samples were more pronounced. The polyethylene samples under aeration showed no discoloration or presence of fluorine or chlorine. The polyethylene crevice samples in the ozonated solution all exhibited the distinct brilliant blue color of titanium oxide. Fluorine was found in the corrosion product on only one of the samples. Chlorine was found on the surface of one of the other corrosion coupons. The results of the Teflon{trademark} crevice samples substantiated the previous Rensselaer study.« less

Comparison of the stability of various internal fixators used in the treatment of osteochondritis dissecans--a mechanical model.

PubMed

Morelli, Moreno; Poitras, Philippe; Grimes, Valentine; Backman, David; Dervin, Geoffrey

2007-04-01

The purpose of this study was to determine what characteristics of fixation devices used in the treatment of osteochondritis dissecans (OCD) contribute to improved stability to resist shear loading. An OCD model was designed using rigid polyurethane foam. Each specimen consisted of two components, an osteochondral fragment and a corresponding defect. A total of 40 specimens were prepared and assigned to one of four groups: control (no extrinsic stabilizer); two 2-mm-diameter Kirschner wires (K-wires), 40 mm in length; one threaded washer and a 28-mm screw; and one threaded washer and a 38 mm screw. Each specimen was mounted onto an Iosipescu shear test fixture and subjected to shear loads at a pseudo-static displacement rate of 0.075 mm/s. All groups demonstrated some stability; controls were significantly less stable than all other groups. The group with the threaded washer and 38-mm screw demonstrated the greatest stability (p < 0.001), and no difference was noted between the K-wire and 28-mm screw groups. These results suggest that, in this OCD model, friction conferred some intrinsic stability to resist loads in shear. However, stability was improved with the use of long implants that compressed the fragments together.

Oral Performace Scoring Using Generalizability Theory and Many-Facet Rasch Measurement: A Comparison Study

ERIC Educational Resources Information Center

Alkahtani, Saif F.

2012-01-01

The principal aim of the present study was to better guide the Quranic recitation appraisal practice by presenting an application of Generalizability theory and Many-facet Rasch Measurement Model for assessing the dependability and fit of two suggested rubrics. Recitations of 93 students were rated holistically and analytically by 3 independent…

Energy consumption and usage characteristics from field measurements of residential dishwashers, clothes washers and clothes dryers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Y.L.; Grot, R.A.

1980-10-01

The measured energy consumption and usage characteristics for household dishwashers, clothes washers, and clothes dryers for ten townhouses at Twin Rivers, N.J., are presented. Whenever the dishwashers and/or clothes washers were in use, the energy consumption, water consumption, frequency of usage, and water temperature were measured by a data acquisition system. The electrical energy of electric clothes dryers and the gas consumption of gas clothes dryers were measured, as well as their frequency and duration of use, and exhaust temperature. Typical household usage patterns of these major appliances are included.

Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards and Labeling Programs for Clothes Washers, Water Dispensers, Vending Machines and CFLs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fridley, David; Zheng, Nina; Zhou, Nan

Since the late 1970s, energy labeling programs and mandatory energy performance standards have been used in many different countries to improve the efficiency levels of major residential and commercial equipment. As more countries and regions launch programs covering a greater range of products that are traded worldwide, greater attention has been given to harmonizing the specific efficiency criteria in these programs and the test methods for measurements. For example, an international compact fluorescent light (CFL) harmonization initiative was launched in 2006 to focus on collaboration between Australia, China, Europe and North America. Given the long history of standards and labelingmore » programs, most major energy-consuming residential appliances and commercial equipment are already covered under minimum energy performance standards (MEPS) and/or energy labels. For these products, such as clothes washers and CFLs, harmonization may still be possible when national MEPS or labeling thresholds are revised. Greater opportunity for harmonization exists in newer energy-consuming products that are not commonly regulated but are under consideration for new standards and labeling programs. This may include commercial products such as water dispensers and vending machines, which are only covered by MEPS or energy labels in a few countries or regions. As China continues to expand its appliance standards and labeling programs and revise existing standards and labels, it is important to learn from recent international experiences with efficiency criteria and test procedures for the same products. Specifically, various types of standards and labeling programs already exist in North America, Europe and throughout Asia for products in China's 2010 standards and labeling programs, namely clothes washers, water dispensers, vending machines and CFLs. This report thus examines similarities and critical differences in energy efficiency values, test procedure specifications and other technical performance requirements in existing international programs in order to shed light on where Chinese programs currently stands and considerations for their 2010 programs.« less

10 CFR 431.152 - Definitions concerning commercial clothes washers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... electrical, physical, and functional (or hydraulic) characteristics that affect energy consumption, energy... 10 Energy 3 2014-01-01 2014-01-01 false Definitions concerning commercial clothes washers. 431.152 Section 431.152 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN...

10 CFR 431.152 - Definitions concerning commercial clothes washers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... electrical, physical, and functional (or hydraulic) characteristics that affect energy consumption, energy... 10 Energy 3 2012-01-01 2012-01-01 false Definitions concerning commercial clothes washers. 431.152 Section 431.152 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN...

10 CFR 431.152 - Definitions concerning commercial clothes washers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... electrical, physical, and functional (or hydraulic) characteristics that affect energy consumption, energy... 10 Energy 3 2013-01-01 2013-01-01 false Definitions concerning commercial clothes washers. 431.152 Section 431.152 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN...

78 FR 65173 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... washers, which could lead to a local stress concentration resulting in possible reduction of the fatigue... installation. This condition, if not detected and corrected, could lead to a local stress concentration which... incorrectly manufactured special washers, which could lead to a local stress concentration resulting in...

21 CFR 884.1185 - Endometrial washer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Endometrial washer. 884.1185 Section 884.1185 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL...: Only to evaluate the endometrium, (ii) Contraindications: Pregnancy, history of uterine perforation, or...

21 CFR 884.1185 - Endometrial washer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Endometrial washer. 884.1185 Section 884.1185 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL...: Only to evaluate the endometrium, (ii) Contraindications: Pregnancy, history of uterine perforation, or...

21 CFR 884.1185 - Endometrial washer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Endometrial washer. 884.1185 Section 884.1185 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL...: Only to evaluate the endometrium, (ii) Contraindications: Pregnancy, history of uterine perforation, or...

Early tension loss in an anterior cruciate ligament graft. A cadaver study of four tibial fixation devices.

PubMed

Grover, Dustin M; Howell, Stephen M; Hull, Maury L

2005-02-01

The tensile force applied to an anterior cruciate ligament graft determines the maximal anterior translation; however, it is unknown whether the tensile force is transferred to the intra-articular portion of the graft and whether the intra-articular tension and maximal anterior translation are maintained shortly after ligament reconstruction. Ten cadaveric knees were reconstructed with a double-looped tendon graft. The graft was looped through a femoral fixation transducer that measured the resultant force on the proximal end of the graft. A pneumatic cylinder applied a tensile force of 110 N to the graft exiting the tibial tunnel with the knee in full extension. The graft was fixed sequentially with four tibial fixation devices (a spiked metal washer, double staples, a bioabsorbable interference screw, and a WasherLoc). Three cyclic loading treatments designed to conservatively load the graft and its fixation were applied. The combined loss in intra-articular graft tension from friction, insertion of the tibial fixation device, and three cyclic loading treatments was 50% for the spiked washer (p = 0.0004), 100% for the double staples (p < 0.0001), 64% for the interference screw (p = 0.0001), and 56% for the WasherLoc (p < 0.0001). The tension loss caused an increase in the maximal anterior translation from that of the intact knee of 2.0 mm for the spiked washer (p = 0.005), 7.8 mm for the double staples (p < 0.0001), 2.7 mm for the interference screw (p = 0.001), and 2.1 mm for the WasherLoc (p < 0.0001). The tensile force applied to a soft-tissue anterior cruciate ligament graft is not transferred intra-articularly and is not maintained during graft fixation. The loss in tension is caused by friction in the tibial tunnel and wrapping the graft around the shank of the screw of the spiked washer, insertion of the tibial fixation device, and cyclical loading of the knee. The amount of tension loss is sufficient to increase the maximal anterior translation.

76 FR 69869 - Energy Conservation Program: Test Procedures for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-09

... manual water fill control system, user- adjustable adaptive water fill control system, or adaptive water fill control system with alternate manual water fill control system, use the water fill selector... and transcripts, comments, and other supporting documents/ materials. All documents in the docket are...

75 FR 57555 - Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-21

... one signed original paper copy. 4. Hand Delivery/Courier: Ms. Brenda Edwards, U.S. Department of.... Telephone: (202) 586-2945. Please submit one signed original paper copy. For detailed instructions on...-mail: [email protected] . SUPPLEMENTARY INFORMATION: Table of Contents I. Background and Legal...

A survey of decentralized control techniques for large space structures

NASA Technical Reports Server (NTRS)

Lindner, D. K.; Reichard, K.

1987-01-01

Preliminary results on the design of decentralized controllers for the COFS I Mast are reported. A nine mode finite element model is used along with second order model of the actuators. It is shown that without actuator dynamics, the system is stable with collocated rate feedback and has acceptable performace. However, when actuator dynamics are included, the system is unstable.

40 CFR 63.447 - Clean condensate alternative.

Code of Federal Regulations, 2012 CFR

2012-07-01

... equipment includes smelt dissolving tanks, lime mud washers and storage tanks, white and mud liquor... tanks, and dreg washers ending with the white liquor storage tanks prior to the digester system, and any... preparation systems, the paper or paperboard machines, and the paper machine white water system, broke...

40 CFR 63.447 - Clean condensate alternative.

Code of Federal Regulations, 2011 CFR

2011-07-01

... equipment includes smelt dissolving tanks, lime mud washers and storage tanks, white and mud liquor... tanks, and dreg washers ending with the white liquor storage tanks prior to the digester system, and any... preparation systems, the paper or paperboard machines, and the paper machine white water system, broke...

40 CFR 63.447 - Clean condensate alternative.

Code of Federal Regulations, 2013 CFR

2013-07-01

... equipment includes smelt dissolving tanks, lime mud washers and storage tanks, white and mud liquor... tanks, and dreg washers ending with the white liquor storage tanks prior to the digester system, and any... preparation systems, the paper or paperboard machines, and the paper machine white water system, broke...

77. Detail view looking east showing Dovel horizontal gas washer ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

77. Detail view looking east showing Dovel horizontal gas washer in foreground, Rust Co. boilers and blowing engine house at left, and Babcock & Wilcox type boilers at right. - Sloss-Sheffield Steel & Iron, First Avenue North Viaduct at Thirty-second Street, Birmingham, Jefferson County, AL

10 CFR Appendix J1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2013 CFR

2013-01-01

.... The 500g requirement will only be used if a clothes washer design can achieve spin speeds in the 500g... Products, P.O. Box 5127, Toledo, OH 43611) or an equivalent extractor with same basket design (i.e... provide materially inaccurate comparative data, field testing may be appropriate for establishing an...

Trestle #1, detail of bolt and washer on wing wall ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Trestle #1, detail of bolt and washer on wing wall on north west side of northeast abutment. View to northeast - Promontory Route Railroad Trestles, S.P. Trestle 779.91, One mile southwest of junction of State Highway 83 and Blue Creek, Corinne, Box Elder County, UT

Design and analysis of lifting tool assemblies to lift different engine block

NASA Astrophysics Data System (ADS)

Sawant, Arpana; Deshmukh, Nilaj N.; Chauhan, Santosh; Dabhadkar, Mandar; Deore, Rupali

2017-07-01

Engines block are required to be lifted from one place to another while they are being processed. The human effort required for this purpose is more and also the engine block may get damaged if it is not handled properly. There is a need for designing a proper lifting tool which will be able to conveniently lift the engine block and place it at the desired position without any accident and damage to the engine block. In the present study lifting tool assemblies are designed and analyzed in such way that it may lift different categories of engine blocks. The lifting tool assembly consists of lifting plate, lifting ring, cap screws and washers. A parametric model and assembly of Lifting tool is done in 3D modelling software CREO 2.0 and analysis is carried out in ANSYS Workbench 16.0. A test block of weight equivalent to that of an engine block is considered for the purpose of analysis. In the preliminary study, without washer the stresses obtained on the lifting tool were more than the safety margin. In the present design, washers were used with appropriate dimensions which helps to bring down the stresses on the lifting tool within the safety margin. Analysis is carried out to verify that tool design meets the ASME BTH-1 required safety margin.

Foam-reinforced elderly human tibia approximates young human tibia better than porcine tibia: a study of the structural properties of three soft tissue fixation devices.

PubMed

Bailey, Shana B; Grover, Dustin M; Howell, Stephen M; Hull, Maury L

2004-01-01

Because there is an insufficient supply of young human knees, an alternative is needed for evaluating anterior cruciate ligament reconstructions. The authors determined whether an elderly human tibia reinforced with foam is a better substitute for a young human tibia than a porcine tibia in this study of the tibialfixation of a soft tissue anterior cruciate ligament graft using 3 devices. A foam-reinforced elderly human tibia more closely approximates the performance of a young human tibia than porcine tibia. Biomechanical study. Failure mode, stiffness, yield, and slippage were determined for a double-looped tendon graft fixed with either an interference screw, WasherLoc, or tandem washers in young human tibiae, foam-reinforced tibiae from elderly humans, and porcine tibiae. The stiffness and yield of interference screw and WasherLoc fixation in foam-reinforced tibiae more closely approximate those in young human tibiae than in porcine tibiae. Slippage of all combinations of tibiae and fixation devices was similar A foam-reinforced human tibia more closely approximates the performance of a young human tibia than that of porcine tibia in this study. Fixation devices should be tested in foam-reinforced tibiae from elderly humans rather than tibiae from large farm animals when the supply of young human knees is insufficient.

The crevice corrosion behavior of chromium stainless steel and nickel base alloys in a reverse osmosis plant utilizing seawater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Odwani, A.; Carew, J.; Al-Hashem, A.

1999-11-01

The crevice corrosion tests were performed on UNS S31603, UNS S31703, UNS S31726, UNS S31254, UNS N08904, UNS N625, UNS N825 and UNS N276 was investigated in seawater and neutral brine solution using a multiple crevice washer assembly. PTFE multiple-crevice washers were bolted to both sides of the test specimens with PTFE bolts and nuts. The specimens were exposed to seawater flowing at a rate of 100 L/h for periods of 3,000 h and 6,000 h. Duplicate specimens were immersed in a plexiglass cell containing the flowing seawater at a temperature of 30 C. The results showed that all themore » tested coupons were susceptible to some degree of crevice corrosion attack. However, the stainless steels were the most severely affected. The degree of crevice corrosion attack for the nickel base alloys decreased as the percentage of molybdenum content in the alloys increased. Destruction of the passive layer by the concentration of chloride or acidity and reduction of hydrogen ions at the crevices is believed to be the cause of the crevice attack.« less

Development of ion source with a washer gun for pulsed neutral beam injection.

PubMed

Asai, T; Yamaguchi, N; Kajiya, H; Takahashi, T; Imanaka, H; Takase, Y; Ono, Y; Sato, K N

2008-06-01

A new type of economical neutral beam source has been developed by using a single washer gun, pulsed operation, and a simple electrode system. We replaced the conventional hot filaments for arc-discharge-type plasma formation with a single stainless-steel washer gun, eliminating the entire dc power supply for the filaments and the cooling system for the electrodes. Our initial experiments revealed successful beam extraction up to 10 kV and 8.6 A, based on spatial profile measurements of density and temperature in the plasma source. The system also shows the potential to control the beam profile by controlling the plasma parameters in the ion accumulation chamber.

Dielectric supported radio-frequency cavities

DOEpatents

Yu, David U. L.; Lee, Terry G.

2000-01-01

A device which improves the electrical and thermomechanical performance of an RF cavity, for example, in a disk-loaded accelerating structure. A washer made of polycrystalline diamond is brazed in the middle to a copper disk washer and at the outer edge to the plane wave transformer tank wall, thus dissipating heat from the copper disk to the outer tank wall while at the same time providing strong mechanical support to the metal disk. The washer structure eliminates the longitudinal connecting rods and cooling channels used in the currently available cavities, and as a result minimizes problems such as shunt impedance degradation and field distortion in the plane wave transformer, and mechanical deflection and uneven cooling of the disk assembly.

Not all triads are created equal: further support for the importance of visual and semantic proximity in object identification.

PubMed

Schweizer, Tom A; Dixon, Mike J; Desmarais, Geneviève; Smith, Stephen D

2002-01-01

Identification deficits were investigated in ELM, a temporal lobe stroke patient with category-specific deficits. We replicated previous work done on FS, a patient with category specific deficits as a result of herpes viral encephalitis. ELM was tested using novel, computer generated shapes that were paired with artifact labels. We paired semantically close or disparate labels to shapes and ELM attempted to learn these pairings. Overall, ELM's shape-label confusions were most detrimentally affected when we used labels that referred to objects that were visually and semantically close. However, as with FS, ELM had as many errors when shapes were paired with the labels "donut," "tire," and "washer" as he did when they were paired with visually and semantically close artifact labels. Two explanations are put forth to account for the anomalous performance by both patients on the triad of donut-tire-washer.

76 FR 11233 - Energy Conservation Program for Consumer Products: Decision and Order Granting a Waiver to LG...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-01

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy [Case No. CW-016] Energy... Energy Residential Clothes Washer Test Procedure AGENCY: Office of Energy Efficiency and Renewable Energy... 23, 2011. Cathy Zoi, Assistant Secretary, Energy Efficiency and Renewable Energy. Decision and Order...

77 FR 4999 - Decision and Order Granting a Waiver to LG From the Department of Energy Clothes Washer Test...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-01

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy [Case No. CW-022] Decision...: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Decision and Order.... Hogan, Deputy Assistant Secretary for Energy Efficiency, Energy Efficiency and Renewable Energy...

10 CFR 429.46 - Commercial clothes washers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the water factor in gallons per cubic feet per cycle (gal/cu ft/cycle) for units manufactured on or... randomly selected and tested to ensure that— (i) Any represented value of energy or water consumption or other measure of energy or water consumption of a basic model for which consumers would favor lower...

10 CFR 429.46 - Commercial clothes washers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the water factor in gallons per cubic feet per cycle (gal/cu ft/cycle) for units manufactured on or... randomly selected and tested to ensure that— (i) Any represented value of energy or water consumption or other measure of energy or water consumption of a basic model for which consumers would favor lower...

10 CFR 429.46 - Commercial clothes washers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the water factor in gallons per cubic feet per cycle (gal/cu ft/cycle) for units manufactured on or... randomly selected and tested to ensure that— (i) Any represented value of energy or water consumption or other measure of energy or water consumption of a basic model for which consumers would favor lower...

75 FR 57556 - Energy Conservation Program for Consumer Products: Test Procedure for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-21

... signed original paper copy. 4. Hand Delivery/Courier: Ms. Brenda Edwards, U.S. Department of Energy...) 586-2945. Please submit one signed original paper copy. For detailed instructions on submitting....Edwards @ee.doe.gov. SUPPLEMENTARY INFORMATION: Table of Contents I. Background and Legal Authority II...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamza, H.

The National Ignition Facility (NIF) is a directorate of LLNL, a DOE Lab, and is home to the world’s largest laser. This laser shoots its 192 beams at a target about the size of a pencil eraser. Within the target are two main chambers; and depending on the type of shot, those chambers need to be pressurized to a certain point at a very low temperature (18 Kelvin). The component used for keeping the hohlraum at its designated pressure is a Laser Entrance Hole (LEH) window, made from a thin (0.5um) polyimide film and an aluminum washer attached with amore » miniscule amount of polymeric adhesive. One issue that has been known to happen is the chambers will leak, at very low rates (5.0E-7 mBar-liter/s and under). At higher pressures significantly larger leak rates have been observed.There are three proposed mechanisms by which the LEH windows are leaking. The first is that there is a small pinhole somewhere in the freestanding film. This is the most unlikely because before any film is shipped from Luxel, it must pass a 50-75 torr room temperature pressure test. The second is a tear in the film at the edge of the washer. This type of damage suggests that the film is under additional stress at this edge portion and/or the edge of the washer itself is what is doing the damage. Lastly, it has been hypothesized that there are small channels under the window that do not get completely filled by the glue and, if they connect to the edge of the freestanding portion of the film, then the pressure can escape through them. These channels were the mechanism being most directly tested over the course of the experiments.« less

75 FR 10318 - Briggs & Stratton Power Products Group, LLC., Home Power Division, a Subsidiary of Briggs...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-05

... portable generators, home stand-by generators and pressure washers. New findings show that worker... portable generators, home stand-by generators and pressure washers. The amended notice applicable to TA-W... 1974, as amended. Signed in Washington, DC, this 22nd day of February 2010. Elliott S. Kushner...

78 FR 765 - Large Residential Washers From Korea and Mexico; Revised Schedule for the Subject Investigations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-04

... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 701-TA-488 and 731-TA-1199-1200 (Final)] Large Residential Washers From Korea and Mexico; Revised Schedule for the Subject Investigations AGENCY: United... information on this matter by contacting the Commission's TDD terminal on 202-205-1810. Persons with mobility...

75 FR 16753 - Certain Helical Spring Lock Washers From the People's Republic of China: Rescission of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-822] Certain Helical Spring Lock... opportunity to request an administrative review of the antidumping duty order on certain helical spring lock... Works Inc., the petitioner, to conduct an administrative review of Hangzhou Spring Washer Co., Ltd...

77 FR 59719 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... DEPARTMENT OF ENERGY 10 CFR Parts 429 and 430 [Docket Number EERE-2008-BT-STD-0019] RIN 1904-AB90 Energy Conservation Program: Energy Conservation Standards for Residential Clothes Washers AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Notice of effective date and...

Elastic and Inelastic Collisions

ERIC Educational Resources Information Center

Gluck, Paul

2010-01-01

There have been two articles in this journal that described a pair of collision carts used to demonstrate vividly the difference between elastic and inelastic collisions. One cart had a series of washers that were mounted rigidly on a rigid wooden framework, the other had washers mounted on rubber bands stretched across a framework. The rigidly…

The self adapting washer for lag screw fixation of mandibular fractures: finite element analysis and preclinical evaluation.

PubMed

Terheyden, H; Mühlendyck, C; Feldmann, H; Ludwig, K; Härle, F

1999-02-01

Besides rigid fixation, lag screws have distinct advantages compared with plates in appropriate indications in mandibular fractures. However, in current lag screw systems, the relatively small area of the screw head has to transfer the tensile force which can exceed 1000 N in the symphysis, to the thin cortical bone plate. Countersinking, which is obligatory in most systems, will weaken the cortical plate. Finite element analysis (FEA) revealed that load in this situation can exceed the normal tensile strength of metal and bone. Consequently, a new washer was constructed which both increased the supporting surface and did not require countersinking. The washer is self adapting (SAW) to the cortical plate in a defined position, forming a ball and socket joint with the screw head. Using the FEA model, a ten-fold reduction in load on bone and metal was observed with the new washer. In a miniature pig mandibular symphysis fracture model, the clinical applicability and a favourable histological reaction were demonstrated, compared with conventional lag screw designs.

10 CFR Appendix J1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2011 CFR

2011-01-01

.... The 500g requirement will only be used if a clothes washer design can achieve spin speeds in the 500g... Products, P.O. Box 5127, Toledo, OH 43611) or an equivalent extractor with same basket design (i.e... characteristics as to provide materially inaccurate comparative data, field testing may be appropriate for...

10 CFR Appendix J1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2012 CFR

2012-01-01

.... The 500g requirement will only be used if a clothes washer design can achieve spin speeds in the 500g... Products, P.O. Box 5127, Toledo, OH 43611) or an equivalent extractor with same basket design (i.e... characteristics as to provide materially inaccurate comparative data, field testing may be appropriate for...

Structural health monitoring technology for bolted carbon-carbon thermal protection panels

NASA Astrophysics Data System (ADS)

Yang, Jinkyu

2005-12-01

The research in this dissertation is motivated by the need for reliable inspection technologies for the detection of bolt loosening in Carbon-Carbon (C-C) Thermal Protection System (TPS) panels on Space Operation Vehicles (SOV) using minimal human intervention. A concept demonstrator of the Structural Health Monitoring (SHM) system was developed to autonomously detect the degradation of the mechanical integrity of the standoff C-C TPS panels. This system assesses the torque levels of the loosened bolts in the C-C TPS panel, as well as identifies the location of those bolts accordingly. During the course of building the proposed SHM prototype, efforts have been focused primarily on developing a trustworthy diagnostic scheme and a responsive sensor suite. Based on the microcontact conditions and damping phenomena of ultrasonic waves across the bolted joints, an Attenuation-based Diagnostic Method was proposed to assess the fastener integrity by observing the attenuation patterns of the resultant sensor signals. Parametric model studies and prototype testing validated the theoretical explanation of the attenuation-based method. Once the diagnostic scheme was determined, the implementation of a sensor suite was the next step. A new PZT-embedded sensor washer was developed to enhance remote sensing capability and achieve sufficient sensitivity by guiding diagnostic waves primarily through the inspection areas. The sensor-embedded washers replace the existing washers to constitute the sensor network, as well as to avoid jeopardizing the integrity of the original fastener components. After sensor design evolution and appropriate algorithm development, verification tests were conducted using a shaker and a full-scale oven, which simulated the acoustic and thermal environments during the re-entry process, respectively. The test results revealed that the proposed system successfully identifies the loss of the preload for the bolted joints that were loosened. The sensors were also found to be durable under the cyclic mechanical and thermal loads without major failures.

77 FR 46401 - Large Residential Washers From Mexico: Preliminary Determination of Sales at Less Than Fair Value...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

... events have occurred.\\1\\ \\1\\ See Large Residential Washers From the Republic of Korea and Mexico... if, in the event of an affirmative preliminary determination, a request for such postponement is made... the event of a negative preliminary determination, a request for such postponement is made by the...

Universal Assembly for Captive Bolts

NASA Technical Reports Server (NTRS)

Marke, M. L.; Hagopian, B.

1982-01-01

New method allows for virtually any bolt to be easily converted to "captive" bolt. Method eliminates need for separate design for each application. Cup-shaped washer that is flattened secures tap to bolt. Wire attached to tab holds bolt assembly captive. Flattening washer can also be done during installation of bolt. Wash, tab and spacer are all made of corrosion-resistant steel.

78 FR 11154 - Large Residential Washers From the Republic of Korea: Countervailing Duty Order

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-15

... externally mounted steel frame at least six inches high that is designed to house a coin/token operated... ``stacked washer-dryers'' denotes distinct washing and drying machines that are built on a unitary frame and... of steel and is assembled with security fasteners;\\8\\ or \\7\\ ``Payment system electronics'' denotes a...

76 FR 54093 - Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-31

... is found to be incorrect (i.e., the ring can be rotated during any torque check required by this AD), before further flight, replace all hardware at that location (except the saddle washer and retainer) in... that location (except the saddle washer and retainer) in accordance with paragraph 3.B., part B, of the...

76 FR 13169 - Energy Conservation Program for Consumer Products: Decision and Order Granting a Waiver to...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

... Conservation Program for Consumer Products: Decision and Order Granting a Waiver to Samsung Electronics America... Electronics America, Inc. (Samsung) a waiver from the DOE clothes washer test procedure for determining the.... Decision and Order In the Matter of: Samsung Electronics America, Inc. (Case No. CW- 014) I. Background and...

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Code of Federal Regulations, 2011 CFR

2011-10-01

... anchorage nuts, plates, or washers, need not have such hardware, but shall have 7/16-20 UNF-2A or 1/2-13UNC... plates or washers furnished for universal floor, installations shall be of steel, free from burrs and... 2580 mm2 in projected area. The distance between any edge of the plate and the edge of the bolt hole...

77 FR 75988 - Notice of Final Determination of Sales at Less Than Fair Value: Large Residential Washers From...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... externally mounted steel frame at least six inches high that is designed to house a coin/token operated... washer-dryers'' denotes distinct washing and drying machines that are built on a unitary frame and share... of steel and is assembled with security fasteners;\\7\\ or \\6\\ ``Payment system electronics'' denotes a...

77 FR 76288 - Notice of Final Determination of Sales at Less Than Fair Value: Large Residential Washers from...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-27

... externally mounted steel frame at least six inches high that is designed to house a coin/token operated... ``stacked washer-dryers'' denotes distinct washing and drying machines that are built on a unitary frame and... of steel and is assembled with security fasteners;\\7\\ or \\6\\ ``Payment system electronics'' denotes a...

Auditory and Subjective Effects of Airborne Noise from Industrial Ultrasonic Sources

PubMed Central

Acton, W. I.; Carson, M. B.

1967-01-01

This investigation was undertaken primarily to examine the possibility of hearing damage from industrial ultrasonic equipment. In the factory concerned, ultrasonic washers and drills were used at a number of different locations, and girls working 12 ft (3·6 m.) away from one bank of three small washers complained of unpleasant subjective effects which included fatigue, persistent headaches, nausea, and tinnitus. As personnel working in the vicinity of similar washers in other parts of the factory did not complain of these effects, it seemed possible that the noise had been transmitted along a column of air in a bank of dryboxes. Enclosure of these washers by a sliding screen of Perspex had completely abated the trouble. Sound pressure level measurements taken in the positions occupied by the operators indicated that, when the effects occur, they are probably caused by high sound levels at the upper audio-frequencies present with the ultrasonic noise, and this was supported by a limited laboratory investigation. Audiometric investigation showed that hearing damage due to noise from these industrial ultrasonic devices is unlikely. However, extrapolations of currently accepted hearing damage risk criteria may be valid in predicting the occurrence of these subjective effects. Images PMID:6073088

Rolling Contact Fatigue Failure Mechanisms of Plasma-Nitrided Ductile Cast Iron

NASA Astrophysics Data System (ADS)

Wollmann, D.; Soares, G. P. P. P.; Grabarski, M. I.; Weigert, N. B.; Escobar, J. A.; Pintaude, G.; Neves, J. C. K.

2017-05-01

Rolling contact fatigue (RCF) of a nitrided ductile cast iron was investigated. Flat washers machined from a pearlitic ductile cast iron bar were quenched and tempered to maximum hardness, ground, polished and divided into four groups: (1) specimens tested as quenched and tempered; (2) specimens plasma-nitrided for 8 h at 400 °C; (3) specimens plasma-nitrided and submitted to a diffusion process for 16 h at 400 °C; and (4) specimens submitted to a second tempering for 24 h at 400 °C. Hardness profiles, phase analyses and residual stress measurements by x-ray diffraction, surface roughness and scanning electron microscopy were applied to characterize the surfaces at each step of this work. Ball-on-flat washer tests were conducted with a maximum contact pressure of 3.6 GPa, under flood lubrication with a SAE 90 API GL-5 oil at 50 °C. Test ending criterion was the occurrence of a spalling. Weibull analysis was used to characterize RCF's lifetime data. Plasma-nitrided specimens exhibited a shorter RCF lifetime than those just quenched and tempered. The effects of nitriding on the mechanical properties and microstructure of the ductile cast iron are discussed in order to explain the shorter endurance of nitrided samples.

An Examination of Tailored Training Offsets on Core Mortarman Skills Acquisition

DTIC Science & Technology

2016-02-01

e.g., grouping and zeroing a rifle on a range) and a secondary training event (e.g., dime and washer drills). The secondary event is designated as...matching, and true– false. Tests were designed so questions on each version contained matched content. That is, the topic domain addressed by an item...and in focus groups , and captured performance data from multiple sources. The researchers also assisted in developing and evaluating a test of mortar

76 FR 70999 - Notice of Petition for Waiver of LG Electronics U.S.A., Inc. From the Department of Energy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-16

... Petition for Waiver of LG Electronics U.S.A., Inc. From the Department of Energy Clothes Washer Test... comments. SUMMARY: This notice announces receipt of and publishes the LG Electronics U.S.A., Inc. (LG... John I. Taylor, Vice President, Government Relations and Communications, LG Electronics USA, Inc., 1776...

10 CFR Appendix J1 to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Automatic and Semi-Automatic Clothes...

Code of Federal Regulations, 2010 CFR

2010-01-01

... characteristics of the clothes load placed in the clothes container, without allowing or requiring consumer... weight of the clothes load placed in the clothes container, without allowing or requiring consumer....4Clothes container means the compartment within the clothes washer that holds the clothes during the...

Successful off-label use of the Cepheid Xpert GBS in a late-onset neonatal meningitis by Streptococcus agalactiae.

PubMed

Savini, Vincenzo; Marrollo, Roberta; Coclite, Eleonora; Fusilli, Paola; D'Incecco, Carmine; Fazii, Paolo

2014-01-01

We report the case of a late-onset neonatal meningitis by Streptococcus agalactiae (group B Streptococcus - GBS) that was diagnosed with a latex agglutination assay (on cerebrospinal fluid, CSF), as well as by using, for the first time, Xpert GBS (Cepheid, US) on CSF. Due to empirical antibiotics given before sampling, both CSF and blood culture were negative, so the abovementioned diagnostics was crucial. Moreover, the Xpert GBS assay, performed according to an off-label, modified protocol (the system is designed for GBS-carriage intrapartum screening, based on a completely automated real time-Polymerase Chain Reaction) quickly detected the organism's genome target. Although further investigation on this test's performace on CSF is required, then, we trust it may be a promising, quick and precise diagnostic method for infections in newborns.

Environmental assessment for proposed energy conservation standards for three types of consumer products: dishwashers, clothes washers and clothes dryers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-01-01

This environmental assessment (EA) evaluates the environmental impacts resulting from new or amended energy-efficiency standards for dishwashers, clothes washers and clothes dryers as mandated by the National Appliance Energy Conservation Act of 1987. A complete description of the Engineering and Economic Analysis of the proposed standards may be found elsewhere in the Technical Support Document (TSD). All eleven of the scenarios for product design changes described in the Engineering Analysis of the TSD are analyzed in the environmental assessment in the form of levels of pollutant reduction. Level 1 represents the least amount of pollutant reduction, while higher numbered levelsmore » represent increasingly more stringent standards, with correspondingly greater reductions in pollutants. Values for energy savings that result from product design changes are taken from the TSD. These energy savings are based on recent data on actual usage rather than DOE test procedures. 12 refs., 1 fig., 12 tabs.« less

Making `Internal Thermal Energy' Visible

NASA Astrophysics Data System (ADS)

Zou, Xueli

2004-09-01

In a 1992 paper published in this journal, Uri Ganiel described a pair of model carts used to demonstrate elastic and inelastic collisions. The wooden carts had low-friction wheels and a steel-strip bumper on one end. On one of the carts, a number of brass washers were rigidly mounted in vertical stacks to a wooden framework. The other cart was similar except that the washers were tied to rubber bands that were stretched horizontally and diagonally across the framework. When the first cart was rolled into a wall it bounced off with only a small reduction in speed ("elastic" collision). The second cart, on the other hand, was found to come nearly to a complete stop upon colliding with the wall ("inelastic" collision). Following the instructions given in Ganiel's paper, I built a pair of carts and demonstrated them to introductory-level physics students at a large public university. It was interesting to find that many students were distracted by the different-looking structures of the two model carts.2 They thought the different distributions of washers between the carts resulted in the rubber-band cart bouncing back a significantly shorter distance than the rigid-rod one after they both collided with a wall at the same initial speed. Apparently, the students had difficulties in understanding the collisions and used surface features to reason about them. To avoid this superficial distraction and to help students visualize easily "where the kinetic energy goes in an inelastic collision," I modified the rigid-rod cart to have washers fixed on hollow aluminum rods mounted at four different levels horizontally and diagonally (see Fig. 1). The new pair of the model carts look very similar to each other: They have the same bumpers, same wheels, same distributions of washers, and same masses.

University of Maryland Wall Washer Retrofit - LED Modules Replace Halogen Lamps in a Performing Arts Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilkerson, Andrea M.; Abell, Thomas C.; Perrin, Tess E.

The University of Maryland (UMD) began retrofitting halogen wall washers in the Clarice Smith Performing Arts Center (CSPAC) in April 2014. The U.S. Department of Energy (DOE) Solid-State Lighting (SSL) GATEWAY program documented this process through the final installation in March 2015, summarized in this report. The wall washers illuminate hallways lining the atrium, providing task illuminance for transitioning between spaces and visual interest to the atrium boundaries. The main goals of the retrofit were to maintain the visual appearance of the space while reducing maintenance costs – energy savings was considered an additional benefit by UMD Facilities Management. UMDmore » Facilities Management is pleased with the results of this retrofit, and continues to initiate LED retrofit projects across the UMD campus.« less

Go Grey - A Laundry to Landscape Irrigation System

NASA Astrophysics Data System (ADS)

Rajmohan, S.

2017-12-01

California residents have dealt with severe drought and high water bills for the few past years[1]. The objective of our project is to use the concept of greywater irrigation to build a low cost, adaptable, and easy to install irrigation system to collect the greywater from the washing machine and use it to water the plants. This system can reduce a household's water usage, extend the life of a septic system, and save time on watering plants by recycling the water from the washing machine. Our simple system requires PVC pipes, a three-way water diverter (valve), a mesh coffee filter, and a water (rain) barrel. The water from the washing machine travels through the three-way valve, which diverts it either to the garden or to the sewer. The PVC pipes lead outside to the garden, where the water barrel is located. The water goes through the mesh coffee filter that is attached on top of the barrel, so that lint and other impurities can be filtered out. The water collected in the barrel will travel through drip irrigation or through a hose to directly water the roots of the plants. This fully functional greywater system was successfully constructed and tested through various trails. We used a Kenmore standard 4.5 cubic feet front load high efficiency washer which uses less water compared to the traditional washers and measured the water collected in water barrel after each wash. Irrespective of the size of the load, the amount of water collected from each wash remained almost the same.. However, we collected enough grey water from each washer load to fill the rain barrel and water the plants in the garden. We were able apply the concept of greywater irrigation successfully to build our own low cost, adaptable, and easy to install greywater system that can be used in any household to water plants in the garden. Our system recycles the water from the washer instead of just wasting it thereby reducing a household's water usage and water bill especially during the time of drought. [1] U.S.Geological Survey/California Water Science Center - https://ca.water.usgs.gov/data/drought/index.html

Dendritic Zinc Growth in Acid Electrolyte: Effect of the pH

NASA Astrophysics Data System (ADS)

Bengoa, Leandro N.; Pary, Paola; Seré, Pablo R.; Conconi, M. Susana; Egli, Walter A.

2018-03-01

In this paper, dendritic growth at the edges of electrogalvanized steel strip has been studied using a specially designed rotating washer electrode which simulates the fluid dynamic conditions and the current density distribution at the steel strip edge found in a production line. The effect of electrolyte pH and current density on dendritic growth in an acidic zinc plating bath (ZnSO4 and H2SO4) was addressed. The temperature was kept constant at 60 °C. Solution pH was adjusted to 1, 2 or 3 using different amounts of H2SO4. In addition, the influence of temperature on the pH of the solution was determined. The current density was set at 40 or 60 A/dm2, similar to that used in the industry. Deposits were characterized using SEM and XRD. The results showed that pH strongly affects dendrites shape, length and texture. Furthermore, the morphology of dendrites at the washer edge and of deposits on the flat portion of the washer changed considerably as solution pH was increased from 1 to 3. It was found that the morphology of dendrites at the washer edge stems from the morphology of the deposit on its flat portion, which in turn determines their shape.

Comparison of washer-disinfector cleaning indicators: impact of temperature and cleaning cycle parameters.

PubMed

Alfa, Michelle J; Olson, Nancy

2014-02-01

Because automated instrument washer-disinfectors (WD) are widely used in health care to reprocess a variety of medical instruments, we developed a study to compare 3 cleaning indicators to determine whether they detected suboptimal temperature, time, enzymatic detergent, and fluid action in a washer-disinfector. The Miele WD was used for this comparison. One optimal cycle and 14 cycles with suboptimal enzymatic detergent, cleaning time, temperature, or inactive spray arms were evaluated. The cleaning indicators evaluated included the following: Pinnacle Monitor for Automated Enzymatic Cleaning Process (PNCL), Wash-Checks (WC), and TOSI. The scoring system for all 3 indicators was harmonized to a common scale. Soiled tweezers were included in each cycle evaluated. The PNCL, TOSI, and WC cleaning indicators showed significantly more failures at 40°C compared with 60°C (100% vs 0% for PNCL, 17% vs 0% for TOSI, and 60% vs 22% for WC, respectively). There were significantly more failures at suboptimal temperatures with a 2- versus 4-minute cycle (100% vs 0% for PNCL, 17% vs 0% for TOSI, and 17% vs 0% for WC, respectively, for 40°C cycles). Despite suboptimal cleaning cycles, all soiled tweezers looked clean. All 3 cleaning indicators responded to suboptimal WD conditions; however, the PNCL was the most affected by alterations in the cycle conditions evaluated. In simulated use testing, cleaning indicators provided a more sensitive audit tool compared with visual inspection of soiled instruments after automated cleaning. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

The Effects of the Absence of an Adult on the Emergence of Conditioned Reinforcement as a Function of Observation in Preschool Age Children

ERIC Educational Resources Information Center

Zrinzo, Michelle L.

2010-01-01

I tested the effects of the absence of an adult on the observational conditioning effect (Greer & Singer-Dudek, 2008). Neutral stimuli (metal washers) did not function to reinforce performance or learning tasks for three preschool age children as determined by a counterbalanced reversal design for the pre-intervention performance tasks and…

Aviation Requirements for Use of Recycled MIL-PRF-680

DTIC Science & Technology

2012-05-24

components – Approximately 1,000 gallons of virgin MIL-PRF-680 Type II used and disposed every 6 months at Fort Rucker Calculated using the full...capacity of the parts washers – Recycling will reduce the need to purchase virgin solvent and reduce disposal costs – Expressed interest received...with virgin solvent Clarus PCS-25 Parts Washer Clarus Tornado Filtration System INSERT EVENT TITLE – INSERT MONTH & YEAR Aviation Requirements for Use

Demonstration of Advanced Technologies for Multi-Load Washers in Hospitality and Healthcare -- Wastewater Recycling Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyd, Brian K.; Parker, Graham B.; Petersen, Joseph M.

The objective of this demonstration project was to evaluate market-ready retrofit technologies for reducing the energy and water use of multi-load washers in healthcare and hospitality facilities. Specifically, this project evaluated laundry wastewater recycling technology in the hospitality sector and ozone laundry technology in both the healthcare and hospitality sectors. This report documents the demonstration of a wastewater recycling system installed in the Grand Hyatt Seattle.

A novel solution for LED wall lamp design and simulation

NASA Astrophysics Data System (ADS)

Ge, Rui; Hong, Weibin; Li, Kuangqi; Liang, Pengxiang; Zhao, Fuli

2014-11-01

The model of the wall washer lamp and the practical illumination application have been established with a new design of the lens to meet the uniform illumination demand for wall washer lamp based on the Lambertian light sources. Our secondary optical design of freeform surface lens to LED wall washer lamp based on the conservation law of energy and Snell's law can improve the lighting effects as a uniform illumination. With the relationship between the surface of the lens and the surface of the target, a great number of discrete points of the freeform profile curve were obtained through the iterative method. After importing the data into our modeling program, the optical entity was obtained. Finally, to verify the feasibility of the algorithm, the model was simulated by specialized software, with both the LED Lambertian point source and LED panel source model.

Horizontal-axis clothes washer market poised for expansion

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, K.L.

1994-12-31

The availability of energy- and water-efficient horizontal-axis washing machines in the North American market is growing, as US and European manufacturers position for an expected long-term market shift toward horizontal-axis (H-axis) technology. Four of the five major producers of washing machines in the US are developing or considering new H-axis models. New entrants, including US-based Staber Industries and several European manufacturers, are also expected to compete in this market. The intensified interest in H-axis technology is partly driven by speculation that new US energy efficiency standards, to be proposed in 1996 and implemented in 1999, will effectively mandate H-axis machines.more » H-axis washers typically use one-third to two-thirds less energy, water, and detergent than vertical-axis machines. Some models also reduce the energy needed to dry the laundry, since their higher spin speeds extract more water than is typical with vertical-axis designs. H-axis washing machines are the focus of two broadly-based efforts to support coordinated research and incentive programs by electric, gas, and water utilities: The High-Efficiency Laundry Metering/Marketing Analysis (THELMA), and the Consortium for Energy Efficiency (CEE) High-Efficiency Clothes Washer Initiative. These efforts may help to pave the way for new types of marketing partnerships among utilities and other parties that could help to speed adoption of H-axis washers.« less

78 FR 43974 - Energy and Water Use Labeling for Consumer Products Under the Energy Policy and Conservation Act...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-23

...The Commission amends the Energy Labeling Rule (``Rule'') by updating comparability ranges and unit energy costs for many EnergyGuide labels. The Commission also issues a conditional exemption and amendments for modified refrigerator and clothes washer labels to help consumers compare the labels for these products after the implementation of upcoming changes to the Department of Energy (``DOE'') test procedures.

Differences in neuropsychological performance between subtypes of obsessive-compulsive disorder.

PubMed

Nedeljkovic, Maja; Kyrios, Michael; Moulding, Richard; Doron, Guy; Wainwright, Kylie; Pantelis, Chris; Purcell, Rosemary; Maruff, Paul

2009-03-01

Neuropsychological studies have suggested that frontal-striatal dysfunction plays a role in obsessive-compulsive disorder (OCD), although findings have been inconsistent, possibly due to heterogeneity within the disorder and methodological issues. The purpose of the present study was therefore to compare the neuropsychological performance of different subtypes of OCD and matched non-clinical controls (NCs) on the Cambridge Automated Neuropsychological Test Battery (CANTAB). Fifty-nine OCD patients and 59 non-clinical controls completed selected tests from CANTAB examining executive function, visual memory and attentional-set shifting. Depression, anxiety and OCD symptoms were also assessed. From 59 OCD patients, four subtypes were identified: (i) washers; (ii) checkers; (iii) obsessionals; and (iv) mixed symptom profile. Comparisons between washers, checkers, obsessionals and NCs indicated few differences, although checkers were generally found to exhibit poorer performance on spatial working memory, while obsessionals performed poorly on the spatial recognition task. Both checkers and the mixed subgroups showed slowed initial movement on the Stockings of Cambridge planning task and poorer pattern recognition relative to NCs. Overall the results suggested greater impairments in performance on neuropsychological tasks in checkers relative to other subtypes, although the observed effects were small and the conclusions limited by the small subtype samples. Future research will need to account for factors that influence neuropsychological performance in OCD subtypes.

Development of plasma sources for ICRF heating experiment in KMAX mirror device

NASA Astrophysics Data System (ADS)

Sun, Xuan; Liu, Ming; Yi, Hongshen; Lin, Munan; Shi, Peiyun

2016-10-01

KMAX, Keda Mirror with AXisymmeticity, is a tandem mirror machine with a length of 10 meters and diameters of 1.2 meters in the central cell and 0.3 meters in the mirror throat. In the past experiments, the plasma was generated by helicon wave launched from the west end. We obtained the blue core mode in argon discharge, however, it cannot provide sufficient plasma for hydrogen discharge, which is at least 1012 cm-3 required for effective ICRF heating. Several attempts have thus been tried or under design to increase the central cell's plasma density: (1) a washer gun with aperture of 1cm has been successfully tested, and a plasma density of 1013 cm-3 was achieved in the west cell near the gun, however, the plasma is only 1011 cm-3 in the central cell possible due to the mirror trapping and/or neutral quenching effect (2) a larger washer gun with aperture of 2.5 cm and a higher power capacitor bank are being assembled in order to generate more plasmas. In addition, how to mitigate the neutrals is under consideration (3) A hot cathode is been designed and will be tested in combination with plasma gun or alone. Preliminary results from those plasma sources will be presented and discussed.

Natural frequency identification of smart washer by using adaptive observer

NASA Astrophysics Data System (ADS)

Ito, Hitoshi; Okugawa, Masayuki

2014-04-01

Bolted joints are used in many machines/structures and some of them have been loosened during long time use, and unluckily these bolt loosening may cause a great accident of machines/structures system. These bolted joint, especially in important places, are main object of maintenance inspection. Maintenance inspection with human- involvement is desired to be improved owing to time-consuming, labor-intensive and high-cost. By remote and full automation monitoring of the bolt loosening, constantly monitoring of bolted joint is achieved. In order to detect loosening of bolted joints without human-involvement, applying a structural health monitoring technique and smart structures/materials concept is the key objective. In this study, a new method of bolt loosening detection by adopting a smart washer has been proposed, and the basic detection principle was discussed with numerical analysis about frequency equation of the system, was confirmed experimentally. The smart washer used in this study is in cantilever type with piezoelectric material, which adds the washer the self-sensing and actuation function. The principle used to detect the loosening of the bolts is a method of a bolt loosening detection noted that the natural frequency of a smart washer system is decreasing by the change of the bolt tightening axial tension. The feature of this proposed method is achieving to identify the natural frequency at current condition on demand by adopting the self-sensing and actuation function and system identification algorithm for varying the natural frequency depending the bolt tightening axial tension. A novel bolt loosening detection method by adopting adaptive observer is proposed in this paper. The numerical simulations are performed to verify the possibility of the adaptive observer-based loosening detection. Improvement of the detection accuracy for a bolt loosening is confirmed by adopting initial parameter and variable adaptive gain by numerical simulation.

Neutral Beam Source and Target Plasma for Development of a Local Electric Field Fluctuation Diagnostic

NASA Astrophysics Data System (ADS)

Bakken, M. R.; Burke, M. G.; Fonck, R. J.; Lewicki, B. T.; Rhodes, A. T.; Winz, G. R.

2016-10-01

A new diagnostic measuring local E-> (r , t) fluctuations is being developed for plasma turbulence studies in tokamaks. This is accomplished by measuring fluctuations in the separation of the π components in the Hα motional Stark spectrum. Fluctuations in this separation are expected to be Ẽ / ẼEMSE 10-3EMSE 10-3 . In addition to a high throughput, high speed spectrometer, the project requires a low divergence (Ω 0 .5°) , 80 keV, 2.5 A H0 beam and a target plasma test stand. The beam employs a washer-stack arc ion source to achieve a high species fraction at full energy. Laboratory tests of the ion source demonstrate repeatable plasmas with Te 10 eV and ne 1.6 ×1017 m-3, sufficient for the beam ion optics requirements. Te and ne scalings of the ion source plasma are presented with respect to operational parameters. A novel three-phase resonant converter power supply will provide 6 mA/cm2 of 80 keV H0 at the focal plane for pulse lengths up to 15 ms, with low ripple δV / 80 keV 0.05 % at 280 kHz. Diagnostic development and validation tests will be performed on a magnetized plasma test stand with 0.5 T field. The test chamber will utilize a washer-stack arc source to produce a target plasma comparable to edge tokamak plasmas. A bias-plate with programmable power supply will be used to impose Ẽ within the target plasma. Work supported by US DOE Grant DE-FG02-89ER53296.

Thermoacoustic Engines in Alternate Geometry Resonators

DTIC Science & Technology

1997-09-12

paper pieces fabricated by Micatron Incorporated. A schematic of a single stack element is shown in Fig. 3.2. The inner diameter of the pieces was...26.28 cm Figure 3.2: A single element of the radial wave "washer" style stack. The element is composed of silicon bonded mica paper with a thickness...washer shaped pieces of silicon bonded mica paper , described previously. An image of a single stack element is shown in Fig. 3.9. 39 Figure 3.7: The

Water Conservation as a Way to Lessen the Impact of New Construction at the Presidio of Monterey.

DTIC Science & Technology

1983-06-01

and the laundry figure would be about 8 gpcd, rather than 10 gpcd, to reflect the use of off-post laundromats and the use of dry cleaning shops for...but not encugh to make a difference, although the post laundry or laundromat will continue to consume water. Also, mcst new clothes washers are water...and energy effi- cient so no new savings would be available. Future constructicn of laundromats should evaluate the type of washer being installed. 68

Mechanisms of change in ERP treatment of compulsive hand washing: does primary threat make a difference?

PubMed

Cougle, Jesse R; Wolitzky-Taylor, Kate B; Lee, Han-Joo; Telch, Michael J

2007-07-01

The present study sought to examine patterns of habituation in exposure and response prevention (ERP) treatment of compulsive hand washing. Sub-clinical compulsive washers (n=27) with illness or non-illness primary threats were compared in order to detect potential differences in response to a single session of ERP. Changes in anxiety, disgust, and urge to wash were analyzed, and significant reductions in both anxiety and disgust were noted. Urge to wash significantly declined among washers primarily concerned with illness; among those concerned with non-illness threats, urge to wash did not significantly decline. Moreover, anxiety was found to decline when controlling for disgust and vice versa. Lastly, when both anxiety and disgust were entered into a model predicting changes in urge to wash, anxiety but not disgust predicted urge to wash for those with illness-related threats; for washers with non-illness threats, the findings were the reverse. Several clinical and theoretical implications are discussed.

Cadmium Replacements for High Strength Steel Fasteners

DTIC Science & Technology

2005-03-01

w/o corr expos – strippability (MIL-S-5002D) [fstnr & pnl] • bend test after coating reapplication • stress durability (ISO 15330) @ 96 hr before...Immersion Paint Adhesion -----45 washersGalvanic Bi-Metallic Corrosion Strippability Stress Durability Fatigue COF Torque Tension Breakaway Torque Paint...Patrick Doyle (NAWCADLKE) • Selected Issues – Zn vs Cad as control – Grade 8 (150 ksi) vs 180 ksi or 220 ksi fasteners – Use of dry film lubricants

WashWise cleans up the Northwest: Lessons learned from the Northwest high-efficiency clothes washer initiative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon, L.M.; Banks, D.L.; Brenneke, M.E.

1998-07-01

WashWise is a regional market transformation program designed to promote the sale and acceptance or resource-efficient clothes washers (RECWs) in the Northwest through financial incentives, education, and marketing. The Program is sponsored by the Northwest Energy Efficiency Alliance (the Alliance), a non-profit regional consortium of utilities, government, public interest groups, and private sector organizations. WashWise started in May 1997 and will continue through the end of 1999. WashWise works to transform the clothes washer market primarily at the retail level through an in-store instant rebate and a retailer bonus. In addition to financial incentives, WashWise has undertaken a collaborative marketingmore » and promotional campaign to educate consumers about the financial savings and other benefits of RECWs. The program promotes only RECWs that meet strict energy and water savings criteria. WashWise has far exceeded initial expectations; annual program sales goals were met in the first three months. As of June 1998, 30,000 RECWs have been sold through the program (representing approximately 13 percent of the Northwest residential clothes washer market). In addition, over 540 retailers, including national and regional chains, are participating in the program. Preliminary survey results also have also provided evidence of broad customer satisfaction. This paper reviews the key elements that have contributed to the success of the WashWise program. In addition, the paper provides program results and indicates future directions for WashWise and the RECW market.« less

Demonstration of Advanced Technologies for Multi-Load Washers in Hospitality and Healthcare -- Ozone Based Laundry Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyd, Brian K.; Parker, Graham B.; Petersen, Joseph M.

The objective of this demonstration project was to evaluate market-ready retrofit technologies for reducing the energy and water use of multi-load washers in healthcare and hospitality facilities. Specifically, this project evaluated laundry wastewater recycling technology in the hospitality sector and ozone laundry technology in both the healthcare and hospitality sectors. This report documents the demonstration of ozone laundry system installations at the Charleston Place Hotel in Charleston, South Carolina, and the Rogerson House assisted living facility in Boston, Massachusetts.

Preliminary Guidelines for Safe and Effective Use of Hot, High-Pressure Washers for Maintenance Cleaning of Army Vehicles.

DTIC Science & Technology

1982-11-01

26AS TACT (Ctbm onrols st N 19m4i60M, = de IdIM b o1ck numbef) - >While hot, high-pressure washers clean effectively, they can also damage parts on Army...conserve water resources, and reduce the costs of wastewater treatment. The objec- At most Army installations, maintenance cleaning tive of the phase of...Itios Catalog Code 214. Posary not only to control the parameters involved for a more accurate assessment of the potential for damage. 2R. I de ~cia

A study of the contact interaction between a plate with a hole and a washer in the presence of clearances and interferences

NASA Astrophysics Data System (ADS)

Grishin, V. I.

The contact interaction between a plate with a hole and a washer fitted into the hole with a clearance or an interference is investigated analytically using a finite element method implemented in a computer code. Data on changes in stress concentration with the distance from the filled hole to the plate edge are obtained for several materials, including D16-T, AK4-1, V95-T, OT4-1, 30KhGSA, and 30KhGSNA alloys.

Apparatus for testing skin samples or the like

DOEpatents

Holland, J.M.

1982-08-31

An apparatus for testing the permeability of living skin samples has a flat base with a plurality of sample-holding cavities formed in its upper surface, the samples being placed in counterbores in the cavities with the epidermis uppermost. O-rings of Teflon washers are respectively placed on the samples and a flat cover is connected to the base to press the rings against the upper surfaces of the samples. Media to maintain tissue viability and recovery of metabolites is introduced into the lower portion of the sample-holding cavities through passages in the base. Test materials are introduced through holes in the cover plate after assembly of the chamber.

2010 Workplace and Gender Relations Survey of Active Duty Members. Overview Report on Sexual Harassment

DTIC Science & Technology

2011-04-01

getting out of your Service Your work performace decreased WGRA 2010 Q37 Margins of error range from ±1 to ±2 Note. “Large extent” includes the...Mental health care doesn’t work ........ a. b. c. d. e. f. g. h. i. j. k. GENDER-RELATED EXPERIENCES Yes, and your gender was a factor Yes, but your...months prior to taking the survey and the details of incidents they have experienced. The report also includes an analysis of the effectiveness of

Effect of Heat and Chemical Protective Clothing on Sustained Mental Performance by Female Soldiers

DTIC Science & Technology

1988-08-29

environments was done to insure that performace in the HOPP-Control condition rQflooted only the effect of weLring the protective ensemble, and not...average number of targets plotted by the group by Conditions and Elapsed Hours of Work are shown in Pig. A. ANOVA resulted in significant main effects ...in Fig. 5. ANOVA resulted In a highly signifioant Conditions effeot (F=36.71jd.f.z3,192;p(0.00001) and a signifioant effect for Lapsed Hours of Work

Mammalian Toxicology Testing: Problem Definition Study, Personnel Plan.

DTIC Science & Technology

1981-03-01

Technician X X Biochemist X Biologist !Bookkeeper Cage Washer X Clinical Chemist Compound Preparation Technician X Computer Cooer X Computer ...Biologist 62 Bookkeeper 60 Cage rasher 33 Clinical Chemist 26 Comp. Prep. Technician 20 Computer Coder 31 Computer Programer 31 Electron Microscope Op...29,200 * Computer Programmer BS S SFByAe 900-2.0 18,400 - $24500 e Lab Tec-inician (Chemistry) BS 5 SF Say Area 16,600- 24.000 - 14.200- ’,0 * Animal

Essays in applied microeconomics

NASA Astrophysics Data System (ADS)

Davis, Lucas William

2005-11-01

The first essay measures the impact of an outbreak of pediatric leukemia on local housing values. A model of residential location choice is used to describe conditions under which the gradient of the hedonic price function with respect to health risk is equal to household marginal willingness to pay to avoid pediatric leukemia risk. This equalizing differential is estimated using property-level sales records from a county in Nevada where residents have recently experienced a severe increase in pediatric leukemia. Housing values are compared before and after the increase with a nearby county acting as a control group. The results indicate that housing values decreased 15.6% during the period of maximum risk. Results are similar for alternative measures of risk and across houses of different sizes. With risk estimates derived using a Bayesian learning model the results imply a statistical value of pediatric leukemia of $5.6 million. The results from the paper provide some of the first market-based estimates of the value of health for children. The second essay evaluates the cost-effectiveness of public incentives that encourage households to purchase high-efficiency durable goods. The demand for durable goods and the demand for energy and other inputs are modeled jointly as the solution to a household production problem. The empirical analysis focuses on the case of clothes washers. The production technology and utilization decision are estimated using household-level data from field trials in which participants received front-loading clothes washers free of charge. The estimation strategy exploits this quasi-random replacement of washers to derive robust estimates of the utilization decision. The results indicate a price elasticity, -.06, that is statistically different from zero across specifications. The parameters from the utilization decision are used to estimate the purchase decision using data from the Consumer Expenditure Survey, 1994-2002. Households consider optimal utilization levels, purchase prices, water rates, energy rates and other factors when deciding which clothes washer to purchase. The complete model is used to simulate the effects of rebate programs and other policies on adoption patterns of clothes washers and household demand for water and energy.

A clamping force measurement system for monitoring the condition of bolted joints on railway track joints and points

NASA Astrophysics Data System (ADS)

Tesfa, B.; Horler, G.; Thobiani, F. Al; Gu, F.; Ball, A. D.

2012-05-01

Many industrial structures associated with railway infrastructures rely on a large number of bolted joint connections to ensure safe and reliable operation of the track and trackside furniture. Significant sums of money are spent annually to repair the damage caused by bolt failures and to maintain the integrity of bolted structures. In the UK, Network Rail (the organization responsible for rail network maintenance and safety) conducts corrective and preventive maintenance manually on 26,000 sets of points (each having approximately 30 bolted joints per set), in order to ensure operational success and safety for the travelling public. Such manual maintenance is costly, disruptive, unreliable and prone to human error. The aim of this work is to provide a means of automatically measuring the clamping force of each individual bolted joint, by means of an instrumented washer. This paper describes the development of a sensor means to be used in the washer, which satisfies the following criteria. Sense changes in the clamping force of the joint and report this fact. Provide compatibility with the large dynamic range of clamping force. Satisfy the limitations in terms of physical size. Provide the means to electronically interface with the washer. Provide a means of powering the washer in situ. Provide a solution at an acceptable cost. Specifically the paper focuses on requirements 1, 2 and 3 and presents the results that support further development of the proposed design and the realization of a pre-prototype system. In the paper, various options for the force sensing element (strain gage, capacitor, piezo-resistive) have been compared, using design optimization techniques. As a result of the evaluation, piezo-resistive sensors in concert with a proprietary force attenuation method, have been found to offer the best performance and cost trade-off The performance of the novel clamping force sensor has been evaluated experimentally and the results show that a smart washer can be developed to monitor the condition of bolted joints as found on railway track and points.

Monitoring of Pre-Load on Rock Bolt Using Piezoceramic-Transducer Enabled Time Reversal Method.

PubMed

Huo, Linsheng; Wang, Bo; Chen, Dongdong; Song, Gangbing

2017-10-27

Rock bolts ensure structural stability for tunnels and many other underground structures. The pre-load on a rock bolt plays an important role in the structural reinforcement and it is vital to monitor the pre-load status of rock bolts. In this paper, a rock bolt pre-load monitoring method based on the piezoceramic enabled time reversal method is proposed. A lead zirconate titanate (PZT) patch transducer, which works as an actuator to generate stress waves, is bonded onto the anchor plate of the rock bolt. A smart washer, which is fabricated by sandwiching a PZT patch between two metal rings, is installed between the hex nut and the anchor plate along the rock bolt. The smart washer functions as a sensor to detect the stress wave. With the increase of the pre-load values on the rock bolt, the effective contact surface area between the smart washer and the anchor plate, benefiting the stress wave propagation crossing the contact surface. With the help of time reversal technique, experimental results reveal that the magnitude of focused signal clearly increases with the increase of the pre-load on a rock bolt before the saturation which happens beyond a relatively high value of the pre-load. The proposed method provides an innovative and real time means to monitor the pre-load level of a rock bolt. By employing this method, the pre-load degradation process on a rock bolt can be clearly monitored. Please note that, currently, the proposed method applies to only new rock bolts, on which it is possible to install the PZT smart washer.

Contact interaction of thin-walled elements with an elastic layer and an infinite circular cylinder under torsion

NASA Astrophysics Data System (ADS)

Kanetsyan, E. G.; Mkrtchyan, M. S.; Mkhitaryan, S. M.

2018-04-01

We consider a class of contact torsion problems on interaction of thin-walled elements shaped as an elastic thin washer – a flat circular plate of small height – with an elastic layer, in particular, with a half-space, and on interaction of thin cylindrical shells with a solid elastic cylinder, infinite in both directions. The governing equations of the physical models of elastic thin washers and thin circular cylindrical shells under torsion are derived from the exact equations of mathematical theory of elasticity using the Hankel and Fourier transforms. Within the framework of the accepted physical models, the solution of the contact problem between an elastic washer and an elastic layer is reduced to solving the Fredholm integral equation of the first kind with a kernel representable as a sum of the Weber–Sonin integral and some integral regular kernel, while solving the contact problem between a cylindrical shell and solid cylinder is reduced to a singular integral equation (SIE). An effective method for solving the governing integral equations of these problems are specified.

Bacteria-free water for automatic washer-disinfectors: an impossible dream?

PubMed

Cooke, R P; Whymant-Morris, A; Umasankar, R S; Goddard, S V

1998-05-01

The ability of a new automatic washer-disinfector system (AWDS), fitted with a water filtration system to provide bacteria-free water and so avoid the risk of mycobacterial contamination of fibreoptic bronchoscopes, was examined. Four new Astec 'MP' Safescope washer-disinfectors, with coarse and fine (0.2 micron) filters attached close to the outlet taps, were supplied with non-softened mains water. Water samples from the tank supply and outlet taps were regularly assessed for bacterial quality over a six-month period. Outlet samples were also analysed after fine filter change and purgation with peracetic acid. All bronchoalveolar lavage specimens (BALS) were stained and cultured for mycobacteria. Only 13 out of 53 outlet samples (24%) were culture-negative. There was no improvement after filter change. Residual anti-bacterial effect of peracetic acid lasted up to 48 h following AWDS purgation. No tank samples were bacteria-free. Sixty BALS were processed, two samples were culture-positive and grew M. tuberculosis and one was also smear-positive. Though mycobacterial contamination of bronchoscopes was not evident, the water filtration system was unable to reliably provide sterile rinse water.

Self-healing bolted joint employing a shape memory actuator

NASA Astrophysics Data System (ADS)

Muntges, Daniel E.; Park, Gyuhae; Inman, Daniel J.

2001-08-01

This paper is a report of an initial investigation into the active control of preload in the joint using a shape memory actuator around the axis of the bolt shaft. Specifically, the actuator is a cylindrical Nitinol washer that expands axially when heated, according to the shape memory effect. The washer is actuated in response to an artificial decrease in torque. Upon actuation, the stress generated by its axial strain compresses the bolted members and creates a frictional force that has the effect of generating a preload and restoring lost torque. In addition to torque wrenches, the system in question was monitored in all stages of testing using piezoelectric impedance analysis. Impedance analysis drew upon research techniques developed at Center for Intelligent Material Systems and Structures, in which phase changes in the impedance of a self-sensing piezoceramic actuator correspond to changes in joint stiffness. Through experimentation, we have documented a successful actuation of the shape memory element. Due to complexity of constitutive modeling, qualitative analysis by the impedance method is used to illustrate the success. Additional considerations encountered in this initial investigation are made to guide further thorough research required for the successful commercial application of this promising technique.

Synthesizing the Nanocrytalline Cobalt-Iron Coating Through The Electrodeposition Process With Different Time Deposition

NASA Astrophysics Data System (ADS)

Rozlin Nik Masdek, Nik; Sorfian Hafiz Mansor, Mohd; Salleh, Zuraidah; Hyie, Koay Mei

2018-03-01

In the engineering world, electrodeposition or electroplating has become the most popular method of surface coating in improving corrosion behavior and mechanical properties of material. Therefore in this study, CoFe nanoparticle protective coating has been synthesized on the mild steel washer using electrodeposition method. The electrodeposition was conducted in the acidic environment with the pH value range from 1 to 2 with the controlled temperature of 50°C. The influence of deposition time (30, 60, 90 minutes) towards characteristic and properties such as particle size, surface morphology, corrosion behavior, and microhardness were studied in this investigation. Several results can be obtained by doing this experiment and testing. First, the surface morphology of Cobalt Iron (CoFe) on the electrodeposited mild steel washer are obtained. In addition, the microhardness of the mild steel washer due to the different deposition time are determined. Next, the observation on the difference in the grain size of CoFe that has been electrodeposited on the mild steel plate is made. Last but not least, the corrosion behavior was investigated. CoFe nanoparticles deposited for 30 minutes produced the smallest particle size and the highest microhardness of 86.17 and 236.84 HV respectively. The CoFe nanoparticles also exhibit the slowest corrosion rate at 30 minutes as compared to others. The crystalline size also increases when the time deposition is increased. The sample with 30 minute depositon time indicate the smallest crystalline size which is 15nm. The decrement of deposition time plays an important role in synthesizing CoFe nanoparticles with good corrosion resistance and microhardness. CoFe nanoparticles obtained at 30 minutes shows high corrosion resistance compared to others. In a nutshell, it was observed that the decrement of deposition time improved mechanical and corrosion properties of CoFe nanoparticles.

Accumulation and distributions of {sup 137}Cs in fresh water snail Pila ampullacea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suseno, Heny, E-mail: henis@batan.go.id

2014-10-24

Pila ampullacea are found in tropical freshwaters of Indonesia. This snail exhibit several characteristics of ideal indicator organisms in order to understand the bioaccumulation of {sup 137}Cs. Biokinetic experiment was performaced in aquaria system and under influenced of concentration K{sup +} in water. The result of experiment shown that Under difference K{sup +} concentration in water, Pila ampullacea have capability to accumulated {sup 137}Cs with CF value range 8.95 to 12.52 ml.g{sup −1}. Both uptake and depuration rate were influenced by concentration of K{sup +} in water.

Assembly for electrical conductivity measurements in the piston cylinder device

DOEpatents

Watson, Heather Christine [Dublin, CA; Roberts, Jeffrey James [Livermore, CA

2012-06-05

An assembly apparatus for measurement of electrical conductivity or other properties of a sample in a piston cylinder device wherein pressure and heat are applied to the sample by the piston cylinder device. The assembly apparatus includes a body, a first electrode in the body, the first electrode operatively connected to the sample, a first electrical conductor connected to the first electrode, a washer constructed of a hard conducting material, the washer surrounding the first electrical conductor in the body, a second electrode in the body, the second electrode operatively connected to the sample, and a second electrical conductor connected to the second electrode.

Development of a low-energy and high-current pulsed neutral beam injector with a washer-gun plasma source for high-beta plasma experiments.

PubMed

Ii, Toru; Gi, Keii; Umezawa, Toshiyuki; Asai, Tomohiko; Inomoto, Michiaki; Ono, Yasushi

2012-08-01

We have developed a novel and economical neutral-beam injection system by employing a washer-gun plasma source. It provides a low-cost and maintenance-free ion beam, thus eliminating the need for the filaments and water-cooling systems employed conventionally. In our primary experiments, the washer gun produced a source plasma with an electron temperature of approximately 5 eV and an electron density of 5 × 10(17) m(-3), i.e., conditions suitable for ion-beam extraction. The dependence of the extracted beam current on the acceleration voltage is consistent with space-charge current limitation, because the observed current density is almost proportional to the 3/2 power of the acceleration voltage below approximately 8 kV. By optimizing plasma formation, we successfully achieved beam extraction of up to 40 A at 15 kV and a pulse length in excess of 0.25 ms. Its low-voltage and high-current pulsed-beam properties enable us to apply this high-power neutral beam injection into a high-beta compact torus plasma characterized by a low magnetic field.

[Significance of working environment improvement based on determination of source of harmful substance--example of an endoscope syringe room using glutaraldehyde].

PubMed

Tashiro, Hiraku; Oda, Susumu; Mori, Koji

2004-03-01

Because a worker complained of irritated eyes and throat due to glutaraldehyde (GA) in an endoscope syringe room, the automated endoscope washers and GA liquid stored in reserve were isolated in a separate room. A ventilation system was installed in this room, and the packing of the automated endoscope washers was changed. However, since the obnoxious smell of GA still remained in the endoscope syringe room, we had to determine the source of the smell. A plastic bucket with a cap was found to be filled with GA for disinfection of the endoscope apparatus. GA had evaporated when dispersed around the bucket, resulting in the obnoxious smell. The plastic bucket was replaced with a different type of container. Moreover, GA from the separate room did not affect the concentration of GA in the working area because the separate room for the automated endoscope washers had twice the ventilation volume proposed by the guidelines of the Society of Gastroenterology Nurses and Associates of the USA and the Healthcare Engineering Association of Japan. Consequently, we reconfirmed the significance of working environment improvement after clarifying the source of the harmful substance.

Method for Evaluating Energy Use of Dishwashers, Clothes Washers, and Clothes Dryers: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eastment, M.; Hendron, R.

Building America teams are researching opportunities to improve energy efficiency for some of the more challenging end-uses, such as lighting (both fixed and occupant-provided), appliances (clothes washer, dishwasher, clothes dryer, refrigerator, and range), and miscellaneous electric loads, which are all heavily dependent on occupant behavior and product choices. These end-uses have grown to be a much more significant fraction of total household energy use (as much as 50% for very efficient homes) as energy efficient homes have become more commonplace through programs such as ENERGY STAR and Building America. As modern appliances become more sophisticated the residential energy analyst ismore » faced with a daunting task in trying to calculate the energy savings of high efficiency appliances. Unfortunately, most whole-building simulation tools do not allow the input of detailed appliance specifications. Using DOE test procedures the method outlined in this paper presents a reasonable way to generate inputs for whole-building energy-simulation tools. The information necessary to generate these inputs is available on Energy-Guide labels, the ENERGY-STAR website, California Energy Commission's Appliance website and manufacturer's literature. Building America has developed a standard method for analyzing the effect of high efficiency appliances on whole-building energy consumption when compared to the Building America's Research Benchmark building.« less

Influence of spore moisture content on the dry-heat resistance of Bacillus subtilis var. niger.

PubMed

Angelotti, R; Maryanski, J H; Butler, T F; Peeler, J T; Campbell, J E

1968-05-01

The dry-heat resistance of Bacillus subtilis var. niger spores located in or on various materials was determined as D and z values in the range of 105 through 160 C. The systems tested included spores located on steel and paper strips, spores located between stainless-steel washers mated together under 150 inch-lb and 12 inch-lb of torque, and spores encapsulated in methylmethacrylate and epoxy plastics. D values for a given temperature varied with the test system. High D values were observed for the systems in which spores were encapsulated or under heavy torque, whereas lower D values were observed for the steel and paper strip systems and the lightly torqued system. Similar z values were obtained for the plastic and steel strip systems (z(D) = 21 C), but an unusually low z for spores on paper (z(D) = 12.9 C) and an unusually high z for spores on steel washers mated at 150 inch-lb of torque (z(D) = 32 C) were observed. The effect of spore moisture content on the D value of spores encapsulated in water-impermeable plastic was determined, and maximal resistance was observed for spores with a water activity (a(w)) of 0.2 to 0.4. Significantly decreased D values were observed for spores with moisture contents below a(w) 0.2 or above a(w) 0.4. The data indicate that the important factors to be considered when measuring the dry heat resistance of spores are (i) the initial moisture content of the spore, (ii) the rate of spore desiccation during heating, (iii) the water retention capacity of the material in or on which spores are located, and (iv) the relative humidity of the system at the test temperature.

Freedrop Testing and CFD Simulation of Ice Models from a Cavity into Supersonic Flow

DTIC Science & Technology

2012-09-01

constructed of stereo lithography (SLA) plastic filled with assorted metal washers for ballast. This allowed the mass and moment of inertia to be finely...set to 0.005 in, with a growth rate of 1.2, extruded out to 0.5 in from the surface of the sphere. The final, multiblock grid input into the OVERFLOW...size article made of balsa wood . While these values illustrate the mass scaling relationship of heavy Mach scaling, with the exception of the 1 Psia case

[Contact dermatitis caused by nickel].

PubMed

Romaguera, C; Grimalt, F; Vilaplana, J; Mascaro, J M

1987-01-01

This paper attempts to explain the initial onset in which the population are sensitized to nickel at an early age, above all in females. A study has been made on 200 controls who tolerated metals and on 964 patents who did not tolerate them. The study comprised of patch tests with 8 distinct washers, made of a variety of metals and alloys all containing nickel, and with nickel sulphate to 1% in petrolatum and cobalt salts to 1% in petrolatum. The results, professional and atopic relationship and other considerations are commented.

Three-phase hypervelocity projectile launcher

DOEpatents

Fugelso, L. Erik; Langner, Gerald C.; Burns, Kerry L.; Albright, James N.

1994-01-01

A hypervelocity projectile launcher for use in perforating borehole casings provides improved penetration into the surrounding rock structure. The launcher includes a first cylinder of explosive material that defines an axial air-filled cavity, a second cylinder of explosive material defining an axial frustum-shaped cavity abutting and axially aligned with the first cylinder. A pliant washer is located between and axially aligned with the first and second cylinders. The frustum shaped cavity is lined with a metal liner effective to form a projectile when the first and second cylinders are detonated. The washer forms a unique intermediate projectile in advance of the liner projectile and enables the liner projectile to further penetrate into and fracture the adjacent rock structure.

Cement technique for reducing post-operative bursitis after trochanteric fixation.

PubMed

Derman, Peter B; Horneff, John G; Kamath, Atul F; Garino, Jonathan

2013-02-01

Post-operative trochanteric bursitis is a known complication secondary to the surgical approach in total hip arthroplasty. This phenomenon may be partially attributable to repetitive microtrauma generated when soft tissues rub against implanted hardware. Significant rates of post-operative trochanteric bursitis have been observed following procedures in which a trochanteric fixation device, such as a bolt-washer mechanism or a cable-grip/claw system, is used to secure the trochanteric fragment after trochanteric osteotomy. We present a simple technique for use with a bolt-washer system or grip plate in which trochanteric components are covered in bone wax followed by a layer of cement to decrease friction and to diminish the risk of post-operative bursitis.

Protective interior wall and attach8ing means for a fusion reactor vacuum vessel

DOEpatents

Phelps, Richard D.; Upham, Gerald A.; Anderson, Paul M.

1988-01-01

An array of connected plates mounted on the inside wall of the vacuum vessel of a magnetic confinement reactor in order to provide a protective surface for energy deposition inside the vessel. All fasteners are concealed and protected beneath the plates, while the plates themselves share common mounting points. The entire array is installed with torqued nuts on threaded studs; provision also exists for thermal expansion by mounting each plate with two of its four mounts captured in an oversize grooved spool. A spool-washer mounting hardware allows one edge of a protective plate to be torqued while the other side remains loose, by simply inverting the spool-washer hardware.

Jovian Tour Design for Orbiter and Lander Missions to Europa

NASA Technical Reports Server (NTRS)

Campagnola, Stefano; Buffington, Brent B.; Petropoulos, Anastassios E.

2013-01-01

Europa is one of the most interesting targets for solar system exploration, as its ocean of liquid water could harbor life. Following the recommendation of the Planetary Decadal Survey, NASA commissioned a study for a flyby mission, an orbiter mission, and a lander mission. This paper presents the moon tours for the lander and orbiter concepts. The total delta v and radiation dose would be reduced by exploiting multi-body dynamics and avoiding phasing loops in the Ganymede-to- Europa transfer. Tour 11-O3, 12-L1 and 12-L4 are presented in details and their performaces compared to other tours from previous Europa mission studies.

Inspection of feasible calibration conditions for UV radiometer detectors with the KI/KIO3 actinometer.

PubMed

Qiang, Zhimin; Li, Wentao; Li, Mengkai; Bolton, James R; Qu, Jiuhui

2015-01-01

UV radiometers are widely employed for irradiance measurements, but their periodical calibrations not only induce an extra cost but also are time-consuming. In this study, the KI/KIO3 actinometer was applied to calibrate UV radiometer detectors at 254 nm with a quasi-collimated beam apparatus equipped with a low-pressure UV lamp, and feasible calibration conditions were identified. Results indicate that a washer constraining the UV light was indispensable, while the size (10 or 50 mL) of a beaker containing the actinometer solution had little influence when a proper washer was used. The absorption or reflection of UV light by the internal beaker wall led to an underestimation or overestimation of the irradiance determined by the KI/KIO3 actinometer, respectively. The proper range of the washer internal diameter could be obtained via mathematical analysis. A radiometer with a longer service time showed a greater calibration factor. To minimize the interference from the inner wall reflection of the collimating tube, calibrations should be conducted at positions far enough away from the tube bottom. This study demonstrates that after the feasible calibration conditions are identified, the KI/KIO3 actinometer can be applied readily to calibrate UV radiometer detectors at 254 nm. © 2014 The American Society of Photobiology.

Design improvement of automated gallon washing machine to minimize musculoskeletal disorders (MSDs) in CV Barokah Abadi using ergonomic function deployment (EFD) approach

NASA Astrophysics Data System (ADS)

Fakhriza, Z.; Rahayu, M.; Iqbal, M.

2017-12-01

In the production activity of Bottled Drinking Water (AMDK) in CV Barokah Abadi there is a gallon washing station. At the work station it involves three stages of activity such as washing and rinsing the outside of the gallon, spraying the inside of the gallon and rubbing the inside of the gallon which is done in a separate place. Distribution of Nordic Body Map (NBM) questionnaires showing employee complaints data at gallon washing stations where workers complained of pain in the right upper arm, right forearm and right wrist respectively 88% and workers also complained of pain in the waist and The right hand respectively by 81%. Ergonomic gallon washer is one way to minimize the risk of MSDs. The design begins with an ergonomic evaluation of the existing conditions and the concept of the initial design of the gallon washer. The evaluation is utilized for consideration of design improvements with the utilization of Ergonomic Function Deployment (EFD) in order for the product concept to conform to the ECSHE principle (Effective, Comfortable, Safe, Healthy and Efficient). The tool improvement design can minimize the risk of MSDs seen from the worker’s posture while using an ergonomic washer.

The cleaning and disinfection by heat of bedpans in automatic and semi-automatic machines.

PubMed Central

Mostafa, A. B.; Chackett, K. F.

1976-01-01

This work is concerned with the cleaning and disinfection by heat of stainless-steel and polypropylene bedpans, which had been soiled with either a biological contaminant, human serum albumin (HSA) labelled with technetium-99m 99m(Tc), or a bacteriological contaminant, streptococcus faecalis mixed with Tc-labelled HSA. Results of cleaning and disinfection achieved with a Test Machine and those achieved by procedures adopted in eight different wards of a general hospital are reported. Bedpan washers installed in wards were found to be less efficient than the Test Machine, at least partly because of inadequate maintenance. Stainless-steel and polypropylene bedpans gave essentially the same results. PMID:6591

Boeing's STAR-FODB test results

NASA Astrophysics Data System (ADS)

Fritz, Martin E.; de la Chapelle, Michael; Van Ausdal, Arthur W.

1995-05-01

Boeing has successfully concluded a 2 1/2 year, two phase developmental contract for the STAR-Fiber Optic Data Bus (FODB) that is intended for future space-based applications. The first phase included system analysis, trade studies, behavior modeling, and architecture and protocal selection. During this phase we selected AS4074 Linear Token Passing Bus (LTPB) protocol operating at 200 Mbps, along with the passive, star-coupled fiber media. The second phase involved design, build, integration, and performance and environmental test of brassboard hardware. The resulting brassboard hardware successfully passed performance testing, providing 200 Mbps operation with a 32 X 32 star-coupled medium. This hardware is suitable for a spaceflight experiment to validate ground testing and analysis and to demonstrate performace in the intended environment. The fiber bus interface unit (FBIU) is a multichip module containing transceiver, protocol, and data formatting chips, buffer memory, and a station management controller. The FBIU has been designed for low power, high reliability, and radiation tolerance. Nine FBIUs were built and integrated with the fiber optic physical layer consisting of the fiber cable plant (FCP) and star coupler assembly (SCA). Performance and environmental testing, including radiation exposure, was performed on selected FBIUs and the physical layer. The integrated system was demonstrated with a full motion color video image transfer across the bus while simultaneously performing utility functions with a fiber bus control module (FBCM) over a telemetry and control (T&C) bus, in this case AS1773.

Filtration System for Removal of Depleted Uranium from Water.

DTIC Science & Technology

1988-02-01

PVC, 3-Way 65 1 1" Pressure Control Valve, Posacon #677, PVC Body, EPDM Diaphragm, Threaded Union Ends Valves with Actuators 29 2 1" PVC 3-Way Multi...Gaskets/Clamps 14 24 1/2" x 2 1/4" LG. Machine Bolts 15 32 1,2" Hex Nuts 16 64 1/2" Washer 17 8 1 1𔃼" Full Face Black Rubber Gasket 36 8 5/8" x 3" LG...Machine Bolts 37 8 5/8" Hex Nuts 38 16 5/8" Washers 39 6 3" Full Face Black Rubber Gasket 45 8 1/2" x 2 1/4" Machine Bolts 78 6 1 1/2" K40 Gasket 79 2 2

Apparatuses to support photovoltaic modules

DOEpatents

Ciasulli, John; Jones, Jason

2017-08-22

Methods and apparatuses to support photovoltaic ("PV") modules are described. A saddle bracket has a mounting surface to support one or more PV modules over a tube, a gusset coupled to the mounting surface, and a mounting feature coupled to the gusset to couple to the tube. A grounding washer has a first portion to couple to a support; and a second portion coupled to the first portion to provide a ground path to a PV module. A PV system has a saddle bracket; a PV module over the saddle bracket; and a grounding washer coupled to the saddle bracket and the PV module. Saddle brackets can be coupled to a torque tube at predetermined locations. PV modules can be coupled to the saddle brackets.

An evaluation of the use of chlorine dioxide (Tristel One-Shot) in an automated washer/disinfector (Medivator) fitted with a chlorine dioxide generator for decontamination of flexible endoscopes.

PubMed

Coates, D

2001-05-01

Microbiological tests were carried out to evaluate a new chlorine dioxide sterilant: Tristel OneShot. Preliminary in vitro suspension tests showed that solutions containing around 140 ppm chlorine dioxide achieved a reduction factor exceeding 10(6) of Staphylococcus aureus in 1min and of Bacillus subtilis spores in 2.5 min in the presence of 3g/L bovine albumin. Subsequent tests evaluated the effectiveness of Tristel One-Shot in a Medivator washer/disinfector fitted with a Tristel Generator for processing flexible endoscopes. Each test run involved three stages. In the first, the instrument and air-water channels of a gastroscope were inoculated with a suspension of Pseudomonas aeruginosa (10(8)cfu/ml) in 10% sodium glutamate and serum (0, 5 or 10%) and then drained, partially dried, and saline flushed through for total viable counts (TVCs). In the second stage, the channels were re-inoculated with test organisms; detergent was flushed through the channels which were then brushed; and saline was flushed through for TVCs. In the third stage, the channels were re-inoculated; detergent was flushed through the channels which were then brushed; the endoscope was processed in the Medivator; and saline was flushed through for TVCs. Carrying out all three stages enabled determination of (1) the contribution played by manual cleaning of channels prior to processing in the Medivator, and (2) the combined effect of manual cleaning followed by processing. Two series of test runs were done. In the first, the Tristel Generator was set to generate 230ppm chlorine dioxide, and in the second 150ppm. In the first, cleaning followed by processing in the Medivator consistently achieved a >/= 10(6)-fold reduction of test organisms, and in the second a >/= 10(5)-fold reduction. Pre-cleaning of channels was very important-when done the initial concentration of serum in the inoculum (0-10%) had no affect on the results obtained after processing. Copyright 2001 The Hospital infection Society.

Use of DSC and DMA Techniques to Help Investigate a Material Anomaly for PTFE Used in Processing a Piston Cup for the Urine Processor Assembly (UPA) on International Space Station (ISS)

NASA Technical Reports Server (NTRS)

Wingard, Doug

2010-01-01

Human urine and flush water are eventually converted into drinking water with the Urine Processor Assembly (UPA) aboard the International Space Station (ISS). This conversion is made possible through the Distillation Assembly (DA) of the UPA. One component of the DA is a molded circular piston cup made of virgin polytetrafluoroethylene (PTFE). The piston cup is assembled to a titanium component using eight fasteners and washers. Molded PTFE produced for spare piston cups in the first quarter of 2010 was different in appearance and texture, and softer than material molded for previous cups. For the suspect newer PTFE material, cup fasteners were tightened to only one-half the required torque value, yet the washers embedded almost halfway into the material. The molded PTFE used in the DA piston cup should be Type II, based on AMS 3667D and ASTM D4894 specifications. The properties of molded PTFE are considerably different between Type I and II materials. Engineers working with the DA thought that if Type I PTFE was molded by mistake instead of Type II material, that could have resulted in the anomalous material properties. Typically, the vendor molds flat sheet PTFE from the same material lot used to mold the piston cups, and tensile testing as part of quality control should verify that the PTFE is Type II material. However, for this discrepant lot of material, such tensile data was not available. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) were two of the testing techniques used at the NASA/Marshall Space Flight Center (MSFC) to investigate the anomaly for the PTFE material. Other techniques used on PTFE specimens were: Shore D hardness testing, tensile testing on dog bone specimens and a qualitative estimation of porosity by optical and scanning electron microscopy.

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2012 CFR

2012-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

TXCHEM HE-1000™

EPA Pesticide Factsheets

Technical product bulletin: this surface washing agent used in oil spill cleanups is applied by pressure sprayer, heated pressure washer, fire hoses, or mixing on or into hydrocarbon contaminated media.

Emission characteristics of VOCs emitted from consumer and commercial products and their ozone formation potential.

PubMed

Dinh, Trieu-Vuong; Kim, Su-Yeon; Son, Youn-Suk; Choi, In-Young; Park, Seong-Ryong; Sunwoo, Young; Kim, Jo-Chun

2015-06-01

The characteristics of volatile organic compounds (VOCs) emitted from several consumer and commercial products (body wash, dishwashing detergent, air freshener, windshield washer fluid, lubricant, hair spray, and insecticide) were studied and compared. The spray products were found to emit the highest amount of VOCs (~96 wt%). In contrast, the body wash products showed the lowest VOC contents (~1.6 wt%). In the spray products, 21.6-96.4 % of the VOCs were propane, iso-butane, and n-butane, which are the components of liquefied petroleum gas. Monoterpene (C10H16) was the dominant component of the VOCs in the non-spray products (e.g., body wash, 53-88 %). In particular, methanol was present with the highest amount of VOCs in windshield washer fluid products. In terms of the number of carbon, the windshield washer fluids, lubricants, insecticides, and hair sprays comprised >95 % of the VOCs in the range C2-C5. The VOCs in the range C6-C10 were predominantly found in the body wash products. The dishwashing detergents and air fresheners contained diverse VOCs from C2 to C11. Besides comprising hazardous VOCs, VOCs from consumer products were also ozone precursors. The ozone formation potential of the consumer and commercial spray products was estimated to be higher than those of liquid and gel materials. In particular, the hair sprays showed the highest ozone formation potential.

Formation mechanism of TiO2 nanotubes and their applications in photoelectrochemical water splitting and supercapacitors.

PubMed

Chen, Bo; Hou, Junbo; Lu, Kathy

2013-05-14

Structural observations of the transition of TiO2 nanopores into nanotubes by increasing the OH(-) concentration in the electrolyte challenge the validity of existing formation mechanisms of anodic TiO2 nanotubes. In this study, dehydration of titanium hydroxide in the cell wall is proposed as the mechanism that leads to the separation of neighboring nanotubes. Based on this understanding, bamboo-type TiO2 nanotubes with large surface area and excellent interconnectivity are achieved by cycling high and low applied potentials. After thermal treatment in a H2 atmosphere, the bamboo-type TiO2 nanotubes show large photoelectrochemical water splitting efficiency and supercapacitors performace.

Proton probing of a relativistic laser interaction with near-critical plasma

NASA Astrophysics Data System (ADS)

Willingale, Louise; Zulick, C.; Thomas, A. G. R.; Maksimchuk, A.; Krushelnick, K.; Nilson, P. M.; Stoeckl, C.; Sangster, T. C.; Nazarov, W.

2014-10-01

The Omega EP laser (1000 J in 10 ps pulses) was used to investigate a relativistic intensity laser interaction with near-critical density plasma using a transverse proton beam to diagnose the large electromagnetic fields generated. A very low density foam target mounted in a washer provided the near-critical density conditions. The fields from a scaled, two-dimensional particle-in-cell simulation were inputed into a particle-tracking code to create simulated proton probe images. This allows us to understand the origins of the complex features in the experimental images, including a rapidly expanding sheath field, evidence for ponderomotive channeling and fields at the foam-washer interface. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0002028.

High temperature penetrator assembly with bayonet plug and ramp-activated lock

NASA Technical Reports Server (NTRS)

Wood, K. E. (Inventor)

1982-01-01

A penetration apparatus, for very high temperature applications in which a base plug is inserted into an opening through a bulkhead is described. The base plug has a head shape and is seated against the highest temperature surface of the bulkhead, which may be the skin of the nose cone or other part of a space vehicle intended for nondestructive atmospheric reentry. From the second side of the bulkhead at which the less severe environment is extant, a bayonet plug is inserted into the base plug and engages an internal shoulder at about 90 deg rotation. The bayonet plug has an integral flanged portion and a pair of ramping washers which are located between the flange and the second bulkhead surface with a spacing washer as necessary.

Simulating the Structural Response of a Preloaded Bolted Joint

NASA Technical Reports Server (NTRS)

Knight, Norman F., Jr.; Phillips, Dawn R.; Raju, Ivatury S.

2008-01-01

The present paper describes the structural analyses performed on a preloaded bolted-joint configuration. The joint modeled was comprised of two L-shaped structures connected together using a single bolt. Each L-shaped structure involved a vertical flat segment (or shell wall) welded to a horizontal segment (or flange). Parametric studies were performed using elasto-plastic, large-deformation nonlinear finite element analyses to determine the influence of several factors on the bolted-joint response. The factors considered included bolt preload, washer-surface-bearing size, edge boundary conditions, joint segment length, and loading history. Joint response is reported in terms of displacements, gap opening, and surface strains. Most of the factors studied were determined to have minimal effect on the bolted-joint response; however, the washer-bearing-surface size affected the response significantly.

ESD Test Apparatus for Soldering Irons

NASA Technical Reports Server (NTRS)

Sancho, Jose; Esser, Robert

2013-01-01

ESDA (Electrostatic Discharge Association) ESD STM 13.1-2000 requires frequent testing of the voltage leakage from the tip of a soldering iron and the resistance from the tip of the soldering iron to the common point ground. Without this test apparatus, the process is time-consuming and requires several wires, alligator clips, or test probes, as well as additional equipment. Soldering iron tips must be tested for electrostatic discharge risks frequently, and this typically takes a lot of time in setup and testing. This device enables the operator to execute the full test in one minute or less. This innovation is a simple apparatus that plugs into a digital multimeter (DMM) and the Common Point Ground (CPG) reference. It enables the user to perform two of the electrostatic discharge tests required in ESD STM 13.1-2000. The device consists of a small black box with two prongs sticking out of one end, two inputs on the opposite end (one of the inputs is used to connect the reference CPG to the DMM), and a metal tab on one side. Inside the box are wires, several washers of various materials, and assembly hardware (nuts and screws/bolts). The device is a passive electronic component that is plugged into a DMM. The operator sets the DMM to read voltage. The operator places the heated tip of the soldering iron onto the metal tab with a small amount of solder to ensure a complete connection. The voltage is read and recorded. The operator switches the DMM to read resistance. The operator places the heated tip of the soldering iron onto the metal tab with a small amount of solder to ensure a complete connection. The resistance is recorded. If the recorded voltage and resistance are below a number stated in ESDA ESD STM 13.1-2000, the test is considered to pass. The device includes all the necessary wiring internal to its body so the operator does not need to do any independent wiring, except for grounding. It uses a stack of high-thermal-resistance washers to minimize the heat transfer from the soldering iron to the wiring used to measure the resistance and voltages. This minimizes thermal error. The device allows very rapid execution of a test that is performed frequently.

PETRO-CLEAN

EPA Pesticide Factsheets

Technical product bulletin: this surface washing agent used in oil spill cleanups on rocks, shorelines, sea walls, bridges, and highways. It is effective when applied through power washers or garden type sprayers in light dilution.

21 CFR 884.1185 - Endometrial washer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... with negative pressure. This device is used to study endometrial cytology (cells). (b) Classification. Class II. The special controls for this device are: (1) FDA's: (i) “Use of International Organization...

77 FR 11416 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-27

.... This proposed AD would require modifying COS boxes by installing new brackets, stiffeners, and hardware... installing new brackets, stiffeners, and hardware (bolts, washers, and nuts) as needed. FAA's Determination...

21 CFR 884.1185 - Endometrial washer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... with negative pressure. This device is used to study endometrial cytology (cells). (b) Classification... a recent cesarean section, and (iii) Warning: Do not attach to a wall or any external suction, and...

Evaluation of replacement thread lubricants for red lead and graphite in mineral oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jungling, T.L.; Rauth, D.R.; Goldberg, D.

1998-04-30

Eight commercially available thread lubricants were evaluated to determine the best replacement for Red Lead and Graphite in Mineral Oil (RLGMO). The evaluation included coefficient of friction testing, high temperature anti-seizing testing, room temperature anti-galling testing, chemical analysis for detrimental impurities, corrosion testing, off-gas testing, and a review of health and environmental factors. The coefficient of friction testing covered a wide variety of factors including stud, nut, and washer materials, sizes, manufacturing methods, surface coatings, surface finishes, applied loads, run-in cycles, and relubrication. Only one lubricant, Dow Corning Molykote P37, met all the criteria established for a replacement lubricant. Itmore » has a coefficient of friction range similar to RLGMO. Therefore, it can be substituted directly for RLGMO without changing the currently specified fastener torque values for the sizes, materials and conditions evaluated. Other lubricants did not perform as well as Molykote P37 in one or more test or evaluation categories.« less

A new anchor augmentation technique with a cancellous screw in osteoporotic rotator cuff repair: an in vitro biomechanical study on sheep humerus specimens.

PubMed

Uruc, Vedat; Ozden, Raif; Dogramacı, Yunus; Kalacı, Aydıner; Hallaceli, Hasan; Küçükdurmaz, Fatih

2014-01-01

The aim of this study was to test a simple technique to augment the pullout resistance of an anchor in an over-drilled sheep humerus model. Sixty-four paired sheep humeri were harvested from 32 male sheep aged 18 months. Specimens were divided into an augmented group and non-augmented group. FASTIN RC 5-mm titanium screw anchors (DePuy Mitek, Raynham, MA) double loaded with suture material (braided polyester, nonabsorbable USP No. 2) were used in both groups. Osteoporosis was simulated by over-drilling with a 4.5-mm drill. Augmentation was performed by fixing 1 of the sutures 1.5 cm inferior to the anchor insertion site with a washer screw. This was followed by a pull-to-failure test at 50 mm/min. The ultimate load (the highest value of strength before anchor pullout) was recorded. A paired t test was used to compare the biomechanical properties of the augmented and non-augmented groups. In all specimens the failure mode was pullout of the anchor. The ultimate failure loads were statistically significantly higher in the augmented group (P < .0001). The mean pullout strength was 121.1 ± 10.17 N in the non-augmented group and 176.1 ± 10.34 N in the augmented group. The described augmentation technique, which is achieved by inferior-lateral fixation of 1 of the sutures of the double-loaded anchor to a fully threaded 6.5-mm cancellous screw with a washer, significantly increases the ultimate failure loads in the over-drilled sheep humerus model. Our technique is simple, safe, and inexpensive. It can be easily used in all osteoporotic patients and will contribute to the reduction of anchor failure. This technique might be difficult to apply arthroscopically. Cannulated smaller screws would probably be more practical for arthroscopic use. Further clinical studies are needed. Copyright © 2014 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Influence of Spore Moisture Content on the Dry-Heat Resistance of Bacillus subtilis var. niger

PubMed Central

Angelotti, Robert; Maryanski, James H.; Butler, Thomas F.; Peeler, James T.; Campbell, Jeptha E.

1968-01-01

The dry-heat resistance of Bacillus subtilis var. niger spores located in or on various materials was determined as D and z values in the range of 105 through 160 C. The systems tested included spores located on steel and paper strips, spores located between stainless-steel washers mated together under 150 inch-lb and 12 inch-lb of torque, and spores encapsulated in methylmethacrylate and epoxy plastics. D values for a given temperature varied with the test system. High D values were observed for the systems in which spores were encapsulated or under heavy torque, whereas lower D values were observed for the steel and paper strip systems and the lightly torqued system. Similar z values were obtained for the plastic and steel strip systems (zD = 21 C), but an unusually low z for spores on paper (zD = 12.9 C) and an unusually high z for spores on steel washers mated at 150 inch-lb of torque (zD = 32 C) were observed. The effect of spore moisture content on the D value of spores encapsulated in water-impermeable plastic was determined, and maximal resistance was observed for spores with a water activity (aw) of 0.2 to 0.4. Significantly decreased D values were observed for spores with moisture contents below aw 0.2 or above aw 0.4. The data indicate that the important factors to be considered when measuring the dry heat resistance of spores are (i) the initial moisture content of the spore, (ii) the rate of spore desiccation during heating, (iii) the water retention capacity of the material in or on which spores are located, and (iv) the relative humidity of the system at the test temperature. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 7 PMID:4968962

78 FR 35604 - Foreign-Trade Zone (FTZ) 155-Calhoun/Victoria Counties, Texas; Notification of Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-13

..., shapes, grommets, clamps, hose, fittings, floor mats, gaskets, seals, insulation and lenses); v-ribbed...); compressors; fans (blades); turbochargers; air conditioners; heat exchangers; filters; windshield washer...

JEP-MARINE CLEAN

EPA Pesticide Factsheets

Technical product bulletin: aka ECOVOOM-MARINE, this surface washing agent is used in oil spill cleanups. Manual pump sprayers should be used to presoak contaminated areas, then pressure washers used to agitate after presoak has been applied.

Stuffed Animals in the Operating Room: A Reservoir of Bacteria With a Simple Solution.

PubMed

Held, Michael; Mignemi, Megan; O'Rear, Lynda; Wise, Michelle; Zane, Gabriella; Murphy Zane, M Siobhan; Schoenecker, Jonathan G

2015-12-01

Despite hand washing and other protocols surgical-site infections (SSIs) have not been eliminated. This implies that either current measures are not effective or there are alternative sources of bacterial exposure to the surgical wound. In this study we tested the hypothesis that stuffed animals or other items allowed to accompany pediatric patients to the operating room as a way to ease anxiety may represent a reservoir of bacteria. Stuffed animals brought into the operating room and stuffed animals that were washed and dried in a conventional washer/dryer and placed in clean sealable plastic bags were swabbed and bacterial colonies were quantified. Results were reported as no growth, light growth, moderate growth, and heavy growth. All stuffed animals showed bacterial growth. A total of 79% of stuffed animals were effectively "sterilized" by a single wash and dry cycle in a conventional home washer/dryer. Sterilized stuffed animals remained sterile after being packed in a sealed bag for 24 hours. These results indicate that items of comfort, such as stuffed animals, brought into the operating room with a benevolent purpose may represent a reservoir of bacteria that could lead to unwanted SSI. Washing an item of comfort 1 day before surgery effectively sterilizes that item of comfort. Future studies will be needed to determine a correlation between "culture positive" stuffed animals and SSI or if providing a child with a "sterile" stuffed animal reduces SSI.

Probe-specific mixed-model approach to detect copy number differences using multiplex ligation-dependent probe amplification (MLPA)

PubMed Central

González, Juan R; Carrasco, Josep L; Armengol, Lluís; Villatoro, Sergi; Jover, Lluís; Yasui, Yutaka; Estivill, Xavier

2008-01-01

Background MLPA method is a potentially useful semi-quantitative method to detect copy number alterations in targeted regions. In this paper, we propose a method for the normalization procedure based on a non-linear mixed-model, as well as a new approach for determining the statistical significance of altered probes based on linear mixed-model. This method establishes a threshold by using different tolerance intervals that accommodates the specific random error variability observed in each test sample. Results Through simulation studies we have shown that our proposed method outperforms two existing methods that are based on simple threshold rules or iterative regression. We have illustrated the method using a controlled MLPA assay in which targeted regions are variable in copy number in individuals suffering from different disorders such as Prader-Willi, DiGeorge or Autism showing the best performace. Conclusion Using the proposed mixed-model, we are able to determine thresholds to decide whether a region is altered. These threholds are specific for each individual, incorporating experimental variability, resulting in improved sensitivity and specificity as the examples with real data have revealed. PMID:18522760

Tibial and fibular nerves evaluation using intraoperative electromyography in rats.

PubMed

Nepomuceno, André Coelho; Politani, Elisa Landucci; Silva, Eduardo Guandelini da; Salomone, Raquel; Longo, Marco Vinicius Losso; Salles, Alessandra Grassi; Faria, José Carlos Marques de; Gemperli, Rolf

2016-08-01

To evaluate a new model of intraoperative electromyographic (EMG) assessment of the tibial and fibular nerves, and its respectives motor units in rats. Eight Wistar rats underwent intraoperative EMG on both hind limbs at two different moments: week 0 and week 12. Supramaximal electrical stimulation applied on sciatic nerve, and compound muscle action potential recorded on the gastrocnemius muscle (GM) and the extensor digitorum longus muscle (EDLM) through electrodes at specifics points. Motor function assessment was performaced through Walking Track Test. Exposing the muscles and nerves for examination did not alter tibial (p=0.918) or fibular (p=0.877) function between the evaluation moments. Electromyography of the GM, innervated by the tibial nerve, revealed similar amplitude (p=0.069) and latency (p=0.256) at week 0 and at 12 weeks, creating a standard of normality. Meanwhile, electromyography of the EDLM, innervated by the fibular nerve, showed significant differences between the amplitudes (p=0.003) and latencies (p=0.021) at the two different moments of observation. Intraoperative electromyography determined and quantified gastrocnemius muscle motor unit integrity, innervated by tibial nerve. Although this study was not useful to, objectively, assess extensor digitorum longus muscle motor unit, innervated by fibular nerve.

48 CFR 52.247-13 - Accessorial Services-Moving Contracts.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of property; e.g., beds and sectional bookcases, and the preparing of appliances; e.g., washers... uncrating and placement of property. The Contractor shall unpack and/or uncrate all property that was packed...

48 CFR 52.247-13 - Accessorial Services-Moving Contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of property; e.g., beds and sectional bookcases, and the preparing of appliances; e.g., washers... uncrating and placement of property. The Contractor shall unpack and/or uncrate all property that was packed...

CORIBA 700 SR

EPA Pesticide Factsheets

Technical product bulletin: this surface washing agent for oil spill cleanups reduces interfacial tension between oil and sand. Contaminated sand is placed in sand washer filled with product, oil floats to surface to remove with auger, then centrifuge sand

16 CFR Appendix F1 to Part 305 - Standard Clothes Washers

Code of Federal Regulations, 2010 CFR

2010-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F1...

16 CFR Appendix F2 to Part 305 - Compact Clothes Washers

Code of Federal Regulations, 2011 CFR

2011-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F2...

16 CFR Appendix F1 to Part 305 - Standard Clothes Washers

Code of Federal Regulations, 2011 CFR

2011-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F1...

16 CFR Appendix F2 to Part 305 - Compact Clothes Washers

Code of Federal Regulations, 2012 CFR

2012-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F2...

16 CFR Appendix F1 to Part 305 - Standard Clothes Washers

Code of Federal Regulations, 2013 CFR

2013-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F1...

16 CFR Appendix F2 to Part 305 - Compact Clothes Washers

Code of Federal Regulations, 2013 CFR

2013-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F2...

16 CFR Appendix F1 to Part 305 - Standard Clothes Washers

Code of Federal Regulations, 2012 CFR

2012-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F1...

16 CFR Appendix F2 to Part 305 - Compact Clothes Washers

Code of Federal Regulations, 2010 CFR

2010-01-01

... CONCERNING DISCLOSURES REGARDING ENERGY CONSUMPTION AND WATER USE OF CERTAIN HOME APPLIANCES AND OTHER PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. F2...

34. ROUGH GAS MAIN RUNNING SOUTHEAST FROM THE BOP SHOP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. ROUGH GAS MAIN RUNNING SOUTHEAST FROM THE BOP SHOP TO THE DUAL VENTURI GAS WASHERS. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

GOLD CREW SW

EPA Pesticide Factsheets

Technical product bulletin: this surface washing agent for oil spill cleanups should be applied through hand pump sprayer and allowed to presoak, time depending on type of oil and weather conditions. Then apply through power washer or steam powered unit.

Advanced digital SAR processing study

NASA Technical Reports Server (NTRS)

Martinson, L. W.; Gaffney, B. P.; Liu, B.; Perry, R. P.; Ruvin, A.

1982-01-01

A highly programmable, land based, real time synthetic aperture radar (SAR) processor requiring a processed pixel rate of 2.75 MHz or more in a four look system was designed. Variations in range and azimuth compression, number of looks, range swath, range migration and SR mode were specified. Alternative range and azimuth processing algorithms were examined in conjunction with projected integrated circuit, digital architecture, and software technologies. The advaced digital SAR processor (ADSP) employs an FFT convolver algorithm for both range and azimuth processing in a parallel architecture configuration. Algorithm performace comparisons, design system design, implementation tradeoffs and the results of a supporting survey of integrated circuit and digital architecture technologies are reported. Cost tradeoffs and projections with alternate implementation plans are presented.

Virucidal effects of rodent cage-cleaning practices on the viability of adenovirus vectors.

PubMed

Porter, Jacqueline D; Lyons, Russette M

2002-09-01

Human adenoviruses and adenoviral vectors are classified as Risk Group 2 agents and require BSL2 containment and practices. An additional consideration in using adenoviruses and viral vectors in laboratory animal studies is the possible transmission of these agents to other animals and/or personnel as a result of viral shedding in animal urine and feces. When handling BSL2 agents, cage-wash staff are required to wear appropriate personnel protective equipment, including scrubs, Tyvek suit, hair covering, dust mask, shoes covers, and gloves. Current decontamination procedures are to bag and autoclave soiled rodent cages containing bedding prior to washing in the cage washer to prevent possible adenoviral transmission. However, the practice of autoclaving softens the polycarbonate-based rodent cages, allowing damaging agents or conditions to affect the integrity of the plastic and degrade the cages. The objective of this study was to determine whether current rodent cage-cleaning practices produced virucidal effects for use in lieu of or prior to autoclaving the cages. We found that heating an Av3GFP vector in a test tube to a temperature of 74 degrees C (165 degrees F) for 6 min conditions equivalent to those of the cage washer resulted in greater than an 11-log reduction in infectivity of the vector as evaluated by its cytopathic effect on cells. The combination of heating and a liquid, phosphate-free alkaline detergent produced the same reduction in vector infectivity. However, common cage-cleaning solutions alone possessed no virucidal activity. The high temperatures used in cage-washing procedures alone or in combination with a cleaning solution reduced or eliminated the risk of transmission from viral shedding through urine and feces even at vector concentrations far greater than would ever be expected to be present. Autoclaving cages diminishes the stability and integrity of the polycarbonate cages without providing a further reduction in the risk of virus or vector transmission. On the basis of results from this study, new cage-wash recommendations include dumping the contaminated bedding into a HEPA-filtered waste disposal system and autoclaving the bags of bedding before disposal, then cleaning the cages in the rack washer at wash temperatures of 74 degrees C (165 F) and rinse temperatures of 82 degrees C (180 F).

21 CFR 880.6992 - Medical washer-disinfector.

Code of Federal Regulations, 2011 CFR

2011-04-01

... instruments, anesthesia equipment, hollowware, and other medical devices. (b) Classification. Class II...-disinfectors that are intended to clean, high level disinfect, and dry surgical instruments, anesthesia..., low or intermediate level disinfect, and dry surgical instruments, anesthesia equipment, hollowware...

21 CFR 880.6992 - Medical washer-disinfector.

Code of Federal Regulations, 2010 CFR

2010-04-01

... instruments, anesthesia equipment, hollowware, and other medical devices. (b) Classification. Class II...-disinfectors that are intended to clean, high level disinfect, and dry surgical instruments, anesthesia..., low or intermediate level disinfect, and dry surgical instruments, anesthesia equipment, hollowware...

16 CFR 305.11 - Labeling for refrigerators, refrigerator-freezers, freezers, dishwashers, clothes washers, water...

Code of Federal Regulations, 2011 CFR

2011-01-01

... headline, copy, and charts to maintain uniformity for immediate consumer recognition and readability. Trim... faces to be used are indicated on the prototype labels. No hyphenation should be used in setting...

16 CFR 305.11 - Labeling for refrigerators, refrigerator-freezers, freezers, dishwashers, clothes washers, water...

Code of Federal Regulations, 2010 CFR

2010-01-01

... headline, copy, and charts to maintain uniformity for immediate consumer recognition and readability. Trim... faces to be used are indicated on the prototype labels. No hyphenation should be used in setting...

16 CFR 305.11 - Labeling for refrigerators, refrigerator-freezers, freezers, dishwashers, clothes washers, water...

Code of Federal Regulations, 2012 CFR

2012-01-01

... headline, copy, and charts to maintain uniformity for immediate consumer recognition and readability. Trim... faces to be used are indicated on the prototype labels. No hyphenation should be used in setting...

16 CFR 305.11 - Labeling for refrigerators, refrigerator-freezers, freezers, dishwashers, clothes washers, water...

Code of Federal Regulations, 2013 CFR

2013-01-01

... headline, copy, and charts to maintain uniformity for immediate consumer recognition and readability. Trim... faces to be used are indicated on the prototype labels. No hyphenation should be used in setting...

Super Spool: An Experiment in Powerplant Design

ERIC Educational Resources Information Center

Kesler, Ronald

1974-01-01

Discusses the use of rubberbands, an empty wooden thread spool, two wooden matches, a wax washer, and a small nail to conduct an experiment or demonstration in powerplant design. Detailed procedures and suggested activities are included. (CC)

21 CFR 880.6992 - Medical washer-disinfector.

Code of Federal Regulations, 2013 CFR

2013-04-01

... instruments, anesthesia equipment, hollowware, and other medical devices. (b) Classification. Class II...-disinfectors that are intended to clean, high level disinfect, and dry surgical instruments, anesthesia..., low or intermediate level disinfect, and dry surgical instruments, anesthesia equipment, hollowware...

21 CFR 880.6992 - Medical washer-disinfector.

Code of Federal Regulations, 2012 CFR

2012-04-01

... instruments, anesthesia equipment, hollowware, and other medical devices. (b) Classification. Class II...-disinfectors that are intended to clean, high level disinfect, and dry surgical instruments, anesthesia..., low or intermediate level disinfect, and dry surgical instruments, anesthesia equipment, hollowware...

21 CFR 880.6992 - Medical washer-disinfector.

Code of Federal Regulations, 2014 CFR

2014-04-01

... instruments, anesthesia equipment, hollowware, and other medical devices. (b) Classification. Class II...-disinfectors that are intended to clean, high level disinfect, and dry surgical instruments, anesthesia..., low or intermediate level disinfect, and dry surgical instruments, anesthesia equipment, hollowware...

Appliance Efficiency Standards and Price Discrimination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spurlock, Cecily Anna

2013-05-08

I explore the effects of two simultaneous changes in minimum energy efficiency and ENERGY STAR standards for clothes washers. Adapting the Mussa and Rosen (1978) and Ronnen (1991) second-degree price discrimination model, I demonstrate that clothes washer prices and menus adjusted to the new standards in patterns consistent with a market in which firms had been price discriminating. In particular, I show evidence of discontinuous price drops at the time the standards were imposed, driven largely by mid-low efficiency segments of the market. The price discrimination model predicts this result. On the other hand, in a perfectly competition market, pricesmore » should increase for these market segments. Additionally, new models proliferated in the highest efficiency market segment following the standard changes. Finally, I show that firms appeared to use different adaptation strategies at the two instances of the standards changing.« less

16 CFR 305.11 - Labeling for refrigerators, refrigerator-freezers, freezers, dishwashers, clothes washers, water...

Code of Federal Regulations, 2014 CFR

2014-01-01

... immediate consumer recognition and readability. Trim size dimensions for all labels shall be as follows... on the label. Specific sizes and faces to be used are indicated on the prototype labels. No...

Warranty Decision Process.

DTIC Science & Technology

1982-02-01

come to expect when they purchase the products. Examples of this are found in the automobile, lawn - mower , household appliance and small engine...and stations--make significant acquisitions of commercial appliances such as washers, dryers, dishwashers, lawn - mowers and the like. Whichever command

The effect of compression on individual pressure vessel nickel/hydrogen components

NASA Technical Reports Server (NTRS)

Manzo, Michelle A.; Perez-Davis, Marla E.

1988-01-01

Compression tests were performed on representative Individual Pressure Vessel (IPV) Nickel/Hydrogen cell components in an effort to better understand the effects of force on component compression and the interactions of components under compression. It appears that the separator is the most easily compressed of all of the stack components. It will typically partially compress before any of the other components begin to compress. The compression characteristics of the cell components in assembly differed considerably from what would be predicted based on individual compression characteristics. Component interactions played a significant role in the stack response to compression. The results of the compression tests were factored into the design and selection of Belleville washers added to the cell stack to accommodate nickel electrode expansion while keeping the pressure on the stack within a reasonable range of the original preset.

Flame resistant nontoxic polymer development

NASA Technical Reports Server (NTRS)

Paciorek, K. L.; Karle, D. W.; Kratzer, R. H.

1975-01-01

A number of homopolymers, copolymers, and terpolymers were synthesized employing styrene and four derivatives of diphenyl-p-styrylphosphine. The various polymeric compositions were prepared by two processes, (1) monomer bulk polymerizations and (2) substitution of preformed polydiphenyl-p-styrylphosphine. Results indicate that the majority of the compositions exhibit superior melting and flame retardant characteristics as compared to polystyrene, but are inferior in molding and film forming capability. Terpolymerization appears to result in the materials with the best overall combination of properties. Toxicological evaluation of three representative basic compositions in the form of molded washers showed that no mortalities occurred among the test animals exposed to the products of the oxidative thermal decomposition of the three materials.

78 FR 33339 - Notice of Petitions by Firms for Determination of Eligibility To Apply for Trade Adjustment...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-04

... Firm manufacturers metal parts for IN 46350. air compressors from sheet metal, aluminum and stainless... 17406. as spacers, washers, bushings and pins on multi-spindle automatic screw machines. K&F Electronics...

Structural steel coatings for corrosion mitigation.

DOT National Transportation Integrated Search

2010-10-01

Task 1 of this project was to survey the performance of coating systems for steel bridges in Missouri and to evaluate coating and : recoating practices. Task 1 was led under the direction of Dr. Glenn Washer from the University of Missouri located in...

38. DETAIL OF COOLING WATER BOOSTER PUMP FOR OXYGEN FURNACES, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. DETAIL OF COOLING WATER BOOSTER PUMP FOR OXYGEN FURNACES, LANCES, AND FUME HOODS IN THE GAS WASHER PUMP HOUSE LOOKING EAST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

View south, wharf B, timber framing, detail of cross bracing, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View south, wharf B, timber framing, detail of cross bracing, recent galvanized straps, bolts and washers - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

Market-oriented Programming Using Small-world Networks for Controlling Building Environments

NASA Astrophysics Data System (ADS)

Shigei, Noritaka; Miyajima, Hiromi; Osako, Tsukasa

The market model, which is one of the economic activity models, is modeled as an agent system, and applying the model to the resource allocation problem has been studied. For air conditioning control of building, which is one of the resource allocation problems, an effective method based on the agent system using auction has been proposed for traditional PID controller. On the other hand, it has been considered that this method is performed by decentralized control. However, its decentralization is not perfect, and its performace is not enough. In this paper, firstly, we propose a perfectly decentralized agent model and show its performance. Secondly, in order to improve the model, we propose the agent model based on small-world model. The effectiveness of the proposed model is shown by simulation.

Torque Limit for Bolted Joint for Composites. Part A; TTTC Properties of Laminated Composites

NASA Technical Reports Server (NTRS)

Zhao, Yi

2003-01-01

The existing design code for torque limit of bolted joints for composites at Marshall Space Flight Center is MSFC-STD-486B, which was originally developed in 1960s for metallic materials. The theoretical basis for this code was a simplified mechanics analysis, which takes into account only the bolt, nut and washers, but not the structural members to be connected. The assumption was that metallic materials would not fail due to the bearing stress at the contact area between washer and the mechanical member. This is true for metallic materials; but for composite materials the results could be completely different. Unlike most metallic materials, laminated composite materials have superior mechanical properties (such as modulus and strength) in the in-plane direction, but not in the out-of-plane, or through-the-thickness (TTT) direction. During the torquing, TTT properties (particularly compressive modulus and compressive strength) play a dominant role in composite failure. Because of this concern, structural design engineers at Marshall are currently using a compromised empirical approach: using 50% of the torque value for composite members. Companies like Boeing is using a similar approach. An initial study was conducted last summer on this topic to develop theoretical model(s) that takes into consideration of composite members. Two simplified models were developed based on stress failure criterion and strain failure criterion, respective. However, these models could not be used to predict the torque limit because of the unavailability of material data, specifically, through-the-thickness compression (TTTC) modulus and strength. Therefore, the task for this summer is to experimentally determine the TTTC properties. Due to the time limitation, only one material has been tested: IM7/8552 with [0 degrees,plus or minus 45 degrees, 90 degree ] configuration. This report focuses the test results and their significance, while the experimentation will be described in a separate report by Mr. Kris Kostreva.

A case study of a real-time evaluation of the risk of disease transmission associated with a failure to follow recommended sterilization procedures

PubMed Central

2014-01-01

Background Failures to follow recommendations for reprocessing of surgical instruments may place patients at risk for exposure to pathogenic microorganisms. When such failures occur, medical facilities often face considerable uncertainty and challenges in assessing the actual risks of disease transmission. Methods In 2011, staff at an Ohio hospital determined that surgical instruments inside a Steriset Container had inadvertently been autoclaved on a gravity cycle rather than on the recommended pre-vacuum cycle, potentially exposing 72 patients who underwent surgery with the instruments to risk of infection. To provide an assessment of the level of risk, we tested the effectiveness of the machine washer/disinfector step and of the sterilization process inside the Steriset Container on the gravity cycle for killing of Geobacillus stearothermophilus spores, Clostridium difficile spores, and methicillin-resistant Staphylococcus aureus (MRSA). Based on the test results, the risk of transmission of MRSA by the instruments was calculated and the risk of transmission of hepatitis B virus was estimated. Results The machine washer/disinfector consistently reduced MRSA recovery by a factor of 1:100,000. The sterilization process inside the Steriset Container consistently reduced MRSA concentrations by a factor of >1:10,000,000 and killed 105C. difficile spores and 105G. stearothermophilus spores. The risk of MRSA transmission due to the incident was calculated to be 1 in 100 trillion. Conclusions The risk for transmission of infection due to the failure to follow recommended sterilization processes was negligible based upon complete killing of G. stearothermophilus biological indicator spores, C. difficile spores, and MRSA under conditions that replicated the incident where proper procedures were not followed. Such real-time assessments of the risks associated with specific incidents may provide evidence-based information that can be used to inform decisions regarding disclosure of the incident to patients. PMID:24447336

A case study of a real-time evaluation of the risk of disease transmission associated with a failure to follow recommended sterilization procedures.

PubMed

Donskey, Curtis J; Yowler, Marian; Falck-Ytter, Yngve; Kundrapu, Sirisha; Salata, Robert A; Rutala, William A

2014-01-21

Failures to follow recommendations for reprocessing of surgical instruments may place patients at risk for exposure to pathogenic microorganisms. When such failures occur, medical facilities often face considerable uncertainty and challenges in assessing the actual risks of disease transmission. In 2011, staff at an Ohio hospital determined that surgical instruments inside a Steriset Container had inadvertently been autoclaved on a gravity cycle rather than on the recommended pre-vacuum cycle, potentially exposing 72 patients who underwent surgery with the instruments to risk of infection. To provide an assessment of the level of risk, we tested the effectiveness of the machine washer/disinfector step and of the sterilization process inside the Steriset Container on the gravity cycle for killing of Geobacillus stearothermophilus spores, Clostridium difficile spores, and methicillin-resistant Staphylococcus aureus (MRSA). Based on the test results, the risk of transmission of MRSA by the instruments was calculated and the risk of transmission of hepatitis B virus was estimated. The machine washer/disinfector consistently reduced MRSA recovery by a factor of 1:100,000. The sterilization process inside the Steriset Container consistently reduced MRSA concentrations by a factor of >1:10,000,000 and killed 105C. difficile spores and 105G. stearothermophilus spores. The risk of MRSA transmission due to the incident was calculated to be 1 in 100 trillion. The risk for transmission of infection due to the failure to follow recommended sterilization processes was negligible based upon complete killing of G. stearothermophilus biological indicator spores, C. difficile spores, and MRSA under conditions that replicated the incident where proper procedures were not followed. Such real-time assessments of the risks associated with specific incidents may provide evidence-based information that can be used to inform decisions regarding disclosure of the incident to patients.

21 CFR 129.40 - Equipment and procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION PROCESSING AND BOTTLING OF BOTTLED DRINKING WATER Equipment § 129.40 Equipment... intended use. This includes all collection and storage tanks, piping, fittings, connections, bottle washers...

21 CFR 129.40 - Equipment and procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION PROCESSING AND BOTTLING OF BOTTLED DRINKING WATER Equipment § 129.40 Equipment... intended use. This includes all collection and storage tanks, piping, fittings, connections, bottle washers...

77 FR 7127 - Notice of Petitions by Firms for Determination of Eligibility To Apply for Trade Adjustment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... equipment. Wittek Golf Supply Company, Inc.. 3865 Commercial Avenue, 2/6/2012 The company manufactures golf... golf-related products such as golf balls, ball washers, course signage, club grips, and golf tees. Any...

Cleaning of parts for new manufacturing and parts rebuilding

NASA Astrophysics Data System (ADS)

Doherty, Jeff

1994-06-01

Parts cleaning is the largest single expense, and the most time consuming activity, in rebuilding and new manufacturing. On average, 25% to 40% of the total labor and overhead burden is spent on cleaning. EPA and OSHA pressures add to the burden by making some methods and chemicals obsolete. Some of the processes and chemicals in current use will be curtailed and or outlawed in the future. How can a shops and industries make long term decisions or capital investments in cleaning and process improvements when the government keeps changing its rules? At the MART Corporation in Saint Louis, Missouri, we manufacture a line of cabinet-style batch cleaning machines known as Power Washers. Twenty years ago MART invented and patented the Power Washer process, a cleaning method that recycles wash solution and blasts contaminates as they are washed off the more heavily contaminated parts. Since the initial invention MART has continued to R&D the washing process and develop ancillary systems that comply with EPA and OSHA regulations. For applications involving new industrial parts or items requiring specification cleaned surfaces. MART provides filtration and solution conditioning systems, part drying operations, and triple rinsing. Units are available in stainless steel or higher alloys. We are not alone in the washer manufacturing business. You have many choices of cleaning solutions (no pun intended) which will perform in your operations and yield good results. As a manufacturer, we are interested in your success with our equipment. We have all heard the horror stories of companies having selected inappropriate cleaning systems and or processes which then brought the company to its knees, production wise. Assembly, appearance, warranty, and performance shortcomings of finished products can often be directly related to the cleaning process and its shortcomings.

Cadmium plated steel caps seal anodized aluminum fittings

NASA Technical Reports Server (NTRS)

Padden, J.

1971-01-01

Cadmium prevents fracturing of hard anodic coating under torquing to system specification requirements, prevents galvanic coupling, and eliminates need for crush washers, which, though commonly used in industry, do not correct leakage problem experienced when anodized aluminum fittings and anodized aluminum cap assemblies are joined.

Lockwasher Strongly Resists Disassembly

NASA Technical Reports Server (NTRS)

Jeffers, Stephanie Z.

1991-01-01

Lockwasher designed to prevent counter-rotation and loosening of machine screw once screw tightened. Tabs engage slots in pawl-and-ratchet fashion. Features similar to those of "childproof" cap on pill bottle. Intended to replace cup-washer-and-screwhead combination exposed to high-speed, turbulent flow in turbomachinery.

10 CFR 430.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Standards Institute. Appliance lamp means any lamp that— (1) Is specifically designed to operate in a... clothes washer which has a control system which is capable of scheduling a preselected combination of... to faucets and showerheads: Have the identical flow control mechanism attached to or installed within...

10 CFR 430.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Standards Institute. Appliance lamp means any lamp that— (1) Is specifically designed to operate in a... clothes washer which has a control system which is capable of scheduling a preselected combination of... control mechanism attached to or installed within the fixture fittings, or the identical water-passage...

78 FR 10636 - Large Residential Washers From Korea and Mexico

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-14

... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 701-TA-488 and 731-TA-1199-1200 (Final)] Large... subject investigations, the United States International Trade Commission (Commission) determines, pursuant... notice in the Office of the Secretary, U.S. International Trade Commission, Washington, DC, and by...

Energy Digest.

ERIC Educational Resources Information Center

Gaddy, Carol T., Ed.; Wells, Kathy, Ed.

This collection of reprints offers practical solutions, not readily available elsewhere, to everyday energy problems, such as high utility bills, insulating windows, getting more gas mileage, or buying a more efficient washer or refrigerator. The Arkansas Energy Office provides a weekly column of energy news and conservation tips to newspapers,…

40 CFR 60.621 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the Act and in subpart A of this part. Cartridge filter means a discrete filter unit containing both filter paper and activated carbon that traps and removes contaminants from petroleum solvent, together... cleaning facility that uses petroleum solvent in a combination of washers, dryers, filters, stills, and...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.621 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the Act and in subpart A of this part. Cartridge filter means a discrete filter unit containing both filter paper and activated carbon that traps and removes contaminants from petroleum solvent, together... cleaning facility that uses petroleum solvent in a combination of washers, dryers, filters, stills, and...

40 CFR 60.621 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the Act and in subpart A of this part. Cartridge filter means a discrete filter unit containing both filter paper and activated carbon that traps and removes contaminants from petroleum solvent, together... cleaning facility that uses petroleum solvent in a combination of washers, dryers, filters, stills, and...

40 CFR 60.621 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the Act and in subpart A of this part. Cartridge filter means a discrete filter unit containing both filter paper and activated carbon that traps and removes contaminants from petroleum solvent, together... cleaning facility that uses petroleum solvent in a combination of washers, dryers, filters, stills, and...

40 CFR 60.621 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the Act and in subpart A of this part. Cartridge filter means a discrete filter unit containing both filter paper and activated carbon that traps and removes contaminants from petroleum solvent, together... cleaning facility that uses petroleum solvent in a combination of washers, dryers, filters, stills, and...

36. EASTERN VIEW OF BOTTOM CONE OF GAS COOLING TOWER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. EASTERN VIEW OF BOTTOM CONE OF GAS COOLING TOWER No. 1 AND TWO GAS COOLING TOWER SERVICE WATER PUMPS IN THE GAS WASHER PUMP HOUSE. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

20. INTERIOR OF UTILITY ROOM SHOWING OPEN DOORWAY TO KITCHEN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. INTERIOR OF UTILITY ROOM SHOWING OPEN DOORWAY TO KITCHEN AT PHOTO LEFT, JUNCTION BOXES AT UPPER PHOTO CENTER, AND PLUMBING FOR WASHER AT PHOTO RIGHT. VIEW TO EAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

30 CFR 75.1723 - Stationary grinding machines; protective devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Stationary grinding machines; protective....1723 Stationary grinding machines; protective devices. (a) Stationary grinding machines other than... the wheel. (3) Safety washers. (b) Grinding wheels shall be operated within the specifications of the...

30 CFR 75.1723 - Stationary grinding machines; protective devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Stationary grinding machines; protective....1723 Stationary grinding machines; protective devices. (a) Stationary grinding machines other than... the wheel. (3) Safety washers. (b) Grinding wheels shall be operated within the specifications of the...

A new rabbit model of implant-related biofilm infection: development and evaluation

NASA Astrophysics Data System (ADS)

Chu, Cheng-Bing; Zeng, Hong; Shen, Ding-Xia; Wang, Hui; Wang, Ji-Fang; Cui, Fu-Zhai

2016-03-01

This study is to establish a rabbit model for human prosthetic joint infection and biofilm formation. Thirty-two healthy adult rabbits were randomly divided into four groups and implanted with stainless steel screws and ultra-high molecular weight polyethylene (UHMWPE) washers in the non-articular surface of the femoral lateral condyle of the right hind knees. The rabbit knee joints were inoculated with 1 mL saline containing 0, 102, 103, 104 CFU of Staphylococcus epidermidis ( S. epidermidis) isolated from the patient with total knee arthroplasty (TKA) infection, respectively. On the 14th postoperative day, the UHMWPE washers from the optimal 103 CFU group were further examined. The SEM examination showed a typical biofilm construction that circular S. epidermidis were embedded in a mucous-like matrix. In addition, the LCSM examination showed that the biofilm consisted of the polysaccharide stained bright green fluorescence and S. epidermidis radiating red fluorescence. Thus, we successfully create a rabbit model for prosthetic joint infection and biofilm formation, which should be valuable for biofilm studies.

Design and development of progressive tool for manufacturing washer

NASA Astrophysics Data System (ADS)

Annigeri, Ulhas K.; Raghavendra Ravi Kiran, K.; Deepthi, Y. P.

2017-07-01

In a progressive tool the raw material is worked at different station to finally fabricate the component. A progressive tool is a lucrative tool for mass production of components. A lot of automobile and other transport industries develop progressive tool for the production of components. The design of tool involves lot of planning and the same amount of skill of process planning is required in the fabrication of the tool. The design also involves use of thumb rules and standard elements as per experience gained in practice. Manufacturing the press tool is a laborious task as special jigs and fixtures have to be designed for the purpose. Assembly of all the press tool elements is another task where use of accurate measuring instruments for alignment of various tool elements is important. In the present study, design and fabrication of progressive press tool for production of washer has been developed and the press tool has been tried out on a mechanical type of press. The components produced are to dimensions.

Cleaning and disinfection of equipment for gastrointestinal endoscopy. Report of a Working Party of the British Society of Gastroenterology Endoscopy Committee.

PubMed

1998-04-01

Two per cent glutaraldehyde is the most commonly used disinfectant in endoscopy units within the UK. Unfortunately adverse reactions to glutaraldehyde are common among endoscopy personnel and the Health and Safety Commission has recommended substantial reductions in atmospheric levels of glutaraldehyde in order to comply with the Control of Substances Hazardous to Health Regulations, 1994. The Working Party addressed ways of eliminating or minimising exposure to glutaraldehyde in endoscopy units by reviewing alternative disinfectants and the use of automated washer/disinfectors. Alternatives to glutaraldehyde must be at least as microbicidal as glutaraldehyde, non-irritating and compatible with endoscope components and decontamination equipment. Peracetic acid is a highly effective disinfectant and may be a suitable alternative to glutaraldehyde. Peracetic acid has a vinegary-like odour and is claimed to be less irritating than glutaraldehyde. Experience with this agent remains relatively limited and the Working Party recommends that peracetic acid should be used in sealed or exhaust ventilated facilities until further experience is obtained. It is considerably more expensive than glutaraldehyde, is less stable and large volumes have to be stored. It causes cosmetic (but not functional) damage to endoscopes and is not compatible with some washer/ disinfectors. Chlorine dioxide is a powerful oxidising agent and highly effective as a disinfectant. Once activated it must be stored in sealed containers with little head space. Fumes cause irritation and sealed or exhaust ventilated facilities are necessary. The agent may damage some metallic and polymer components of endoscopes and automated washer/disinfectors and compatibility should be established with equipment manufacturers before the agent is used. Other disinfectants such as peroxygen compounds and quaternary ammonium derivatives are less suitable because of unsatisfactory mycobactericidal and/or virucidal activity, or incompatibility with endoscopes and automated washer/disinfectors. Alcohol is effective but, on prolonged contact, is damaging to lens cements. It is also flammable and therefore unsuitable for use in large quantities in automated systems. Superoxidised water (Sterilox) is an electrochemical solution (anolyte) containing a mixture of radicals with strong oxidising properties. It is highly microbicidal when freshly generated, provided items are thoroughly clean and strict generation criteria are met--that is, current, pH, redox potential. It seems to be safe for users and provided field trials substantiate laboratory efficacy tests, and the agent is non-damaging, it too may become an alternative to glutaraldehyde. When 2% glutaraldehyde is used for manual and automated disinfection, 10 minutes' immersion is recommended for endoscopes before the session and between patients. This will destroy vegetative bacteria and viruses (including hepatitis B virus (HBV) and HIV). A five minute contact period is recommended for 0.35% peracetic acid and for chlorine dioxide (1100 ppm av ClO2), but if immersed for 10 minutes sporicidal activity will also be achieved. At the end of each session 20 minutes' immersion in glutaraldehyde or five minutes in peracetic acid or chlorine dioxide is recommended. Microbiological studies show that 20 minutes of exposure to 2% glutaraldehyde destroys most organisms, including Mycobacterium tuberculosis. The Working Party concludes therefore that immersion of the endoscope in 2% glutaraldehyde for 20 minutes is sufficient for endoscopy involving patients with AIDS and other immunodeficiency states or pulmonary tuberculosis. Similarly, 20 minutes' immersion is recommended at the start of the list and between cases for endoscopic retrograde cholangiopancreatography (ERCP) when high level disinfection is required. Cleaning and disinfection of endoscopes should be undertaken by trained staff in a dedicated room. Thorough cleaning with detergent

Studies on Viral Disinfection: An Evaluation of Moist Heat Disinfection for HBV by Using A0 Concept Defined in ISO 15883-Washer-Disinfectors.

PubMed

Uetera, Yushi; Kawamura, Kunio; Kobayashi, Hiroyoshi; Saito, Yuhei; Yasuhara, Hiroshi; Saito, Ryoichi

2010-01-01

International Organization for Standardization (ISO) 15883 for washer-disinfectors has introduced the A(0) concept to allow comparison of the lethality of moist heat processes. The A(0) value is the equivalent disinfection time in seconds at 80 °C calculated on the basis of microbial killing kinetics when the disinfection temperature is over 65 °C. Hepatitis B virus (HBV), transmissible only to humans and chimpanzees, is an important heat-resistant, blood-borne pathogen. Therefore, it is mandatory to disinfect HBV thoroughly in the washer-disinfectors employed for surgical instruments. Additionally, it has become extremely difficult to use chimpanzees as experimental models or to perform human volunteer studies. Therefore, it is considered worthwhile to re-evaluate the reported data on the moist heat disinfection of HBV using the A(0) value. In the voluntary active immunization to humans in 1973, HBV serum (infectivity titer: 10(6.5) CID(50)/mL) underwent moist heat disinfection at 98 °C for 1 min in a flask over an electric burner (conservatively estimated A(0) value: 3786). Then, 0.1 mL was inoculated to each of 29 volunteers. No one revealed evidence of infection clinically or in the laboratory tests available at the time. In 1979, a more sensitive test appeared and revealed three sub-clinically infected volunteers. In the 1980s, there were two chimpanzee experimental models using HBV serum (infectivity titer: 10(5) CID(50)/mL). In one model, the serum underwent moist heat disinfection at 98 °C for 2 min in a thermostat bath (conservatively estimated A(0) value: 7571). One milliliter was inoculated to each of two chimpanzees, and both of them revealed no evidence of infection. In another model, the serum underwent moist heat disinfection using two conditions in a thermostat bath, respectively: at 103 °C for 90 s (A(0) value: 24865) and at 65 °C for 10 h (A(0) value: 1138). Ten milliliters of each sample were mixed. Then, the mixture was inoculated to each of two chimpanzees. Both of them revealed no evidence of infection. In the human volunteer study, the serum infectivity titer was more than 30 times (10(1.5) times) higher than that used in the two chimpanzee experimental models. Moreover, the serum was heated in the flask over an electric burner, which is considered less reliable than the thermostat baths to realize uniform heat distribution. It is assumed that these factors were predisposed to the result that a conservatively estimated A(0) value of 3786 failed to inactivate the HBV serum of 10(6.5) CID(50)/mL. In the two chimpanzee models, it was suggested that A(0) value not less than 1138 was able to inactivate the HBV serum of 10(5) CID(50)/mL.

Tensiometer with removable wick

DOEpatents

Gee, Glendon W.; Campbell, Melvin D.

1992-01-01

The present invention relates to improvements in tensiometers for measuring soil water tension comprising a rod shaped wick. the rod shaped wick is shoestring, rolled paper towel, rolled glass microfiber filter, or solid ceramic. The rod shaped wick is secured to the tensiometer by a cone washer and a threaded fitting.

10 CFR 431.151 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Purpose and scope. 431.151 Section 431.151 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Commercial Clothers Washers § 431.151 Purpose and scope. This subpart contains energy conservation...

Predicting the Poaceae pollen season: six month-ahead forecasting and identification of relevant features

NASA Astrophysics Data System (ADS)

Navares, Ricardo; Aznarte, José Luis

2017-04-01

In this paper, we approach the problem of predicting the concentrations of Poaceae pollen which define the main pollination season in the city of Madrid. A classification-based approach, based on a computational intelligence model (random forests), is applied to forecast the dates in which risk concentration levels are to be observed. Unlike previous works, the proposal extends the range of forecasting horizons up to 6 months ahead. Furthermore, the proposed model allows to determine the most influential factors for each horizon, making no assumptions about the significance of the weather features. The performace of the proposed model proves it as a successful tool for allergy patients in preventing and minimizing the exposure to risky pollen concentrations and for researchers to gain a deeper insight on the factors driving the pollination season.

Predicting the Poaceae pollen season: six month-ahead forecasting and identification of relevant features.

PubMed

Navares, Ricardo; Aznarte, José Luis

2017-04-01

In this paper, we approach the problem of predicting the concentrations of Poaceae pollen which define the main pollination season in the city of Madrid. A classification-based approach, based on a computational intelligence model (random forests), is applied to forecast the dates in which risk concentration levels are to be observed. Unlike previous works, the proposal extends the range of forecasting horizons up to 6 months ahead. Furthermore, the proposed model allows to determine the most influential factors for each horizon, making no assumptions about the significance of the weather features. The performace of the proposed model proves it as a successful tool for allergy patients in preventing and minimizing the exposure to risky pollen concentrations and for researchers to gain a deeper insight on the factors driving the pollination season.

High performace silicon 2x2 optical switch based on a thermo-optically tunable multimode interference coupler and efficient electrodes.

PubMed

Rosa, Álvaro; Gutiérrez, Ana; Brimont, Antoine; Griol, Amadeu; Sanchis, Pablo

2016-01-11

Optical switches based on tunable multimode interference (MMI) couplers can simultaneously reduce the footprint and increase the tolerance against fabrication deviations. Here, a compact 2x2 silicon switch based on a thermo-optically tunable MMI structure with a footprint of only 0.005 mm(2) is proposed and demonstrated. The MMI structure has been optimized using a silica trench acting as a thermal isolator without introducing any substantial loss penalty or crosstalk degradation. Furthermore, the electrodes performance have significantly been improved via engineering the heater geometry and using two metallization steps. Thereby, a drastic power consumption reduction of around 90% has been demonstrated yielding to values as low as 24.9 mW. Furthermore, very fast switching times of only 1.19 µs have also been achieved.

Home Furnishings and Equipment. Money Management.

ERIC Educational Resources Information Center

Baran, Nancy H., Ed.

This booklet provides guidelines for buying major home appliances from ranges and refrigerators to washers and dryers, as well as wood and upholstered furniture, and bedding and floor coverings, with helpful charts to make selection easier. It begins with suggestions on how to furnish within one's means. Next, information on equipping the home…

75 FR 1121 - Energy Conservation Program: Energy Conservation Standards for Certain Consumer Products...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-08

...The U.S. Department of Energy (DOE) is adopting amended energy conservation standards for commercial clothes washers (CCWs). DOE has determined that amended energy conservation standards for these types of equipment would result in significant conservation of energy, and are technologically feasible and economically justified.

Housekeeping Management Assistant Manual for Training of the Mentally Retarded.

ERIC Educational Resources Information Center

Texas Tech Univ., Lubbock. Research and Training Center in Mental Retardation.

Presented is an instructional guide for teaching mentally retarded persons to become housekeeping assistants. Listed are tasks, objectives, and background information for the following six units: general safety procedures; daily duties (general cleaning, use of supply carts, and bathroom cleaning); laundry procedures (including use of washer and…

78 FR 54383 - Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-04

... the main transmission filter housing upper part and modifying the main transmission housing upper part... filter area was not manufactured in accordance with applicable design specifications. The actions of this... a corrugated washer in the filter housing of the housing upper part and modifying each affected main...

Tensiometer with removable wick

DOEpatents

Gee, G.W.; Campbell, M.D.

1992-04-14

The present invention relates to improvements in tensiometers for measuring soil water tension comprising a rod shaped wick. The rod shaped wick is a shoestring, rolled paper towel, rolled glass microfiber filter, or solid ceramic. The rod shaped wick is secured to the tensiometer by a cone washer and a threaded fitting. 2 figs.

77 FR 50414 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-21

... the drain mast bolts, an inspection to determine the location of the bonding strap, a measurement of... determine the location of the bonding strap, a measurement of the washers under the drain mast bolts, and... measurement. hour = $340. We estimate the following costs to do certain necessary conditional actions that...

76 FR 27610 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-12

..., freezers, water heaters, dishwashers, trash compactors, air conditioners, ovens, microwave ovens, and other... appliance product. A large appliance product is also defined as any organic surface-coated metal range, oven, microwave, refrigerator, freezer, washer, dryer, dishwasher, water heater, or trash compactor manufactured...

40 CFR 60.620 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Performance for Petroleum Dry Cleaners § 60.620 Applicability and designation of affected facility. (a) The provisions of this subpart are applicable to the following affected facilities located at a petroleum dry... pounds): Petroleum solvent dry cleaning dryers, washers, filters, stills, and settling tanks. (1) When...

7. LOOKING WEST TOWARD SHEEP KILL AREA ON SOUTH END ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. LOOKING WEST TOWARD SHEEP KILL AREA ON SOUTH END OF BUILDING 149; INCLINED CONVEYOR AT LEFT CENTER CARRIED TROLLEYS TO THE AUTOMATIC WASHER/OILER ON THE GALLERY LEVEL - Rath Packing Company, Beef Killing Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

Shlepers and Car Washers: Young Israelis in the New York Labor Market.

ERIC Educational Resources Information Center

Ben-Ami, Ilan

1992-01-01

Examines characteristics and immigration experiences of young male Israeli immigrants to New York City who find work in car washes and furniture moving, jobs requiring neither special skills nor work papers. Differences in background and long-range immigration plans between the groups are discussed. (SLD)

76. General view looking east showing Rust Co. boiler stacks ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

76. General view looking east showing Rust Co. boiler stacks at left, Babcock & Wilcox type boiler stacks at right, Dovel horizontal gas washer in foreground, and No. 1 Furnace in distance. - Sloss-Sheffield Steel & Iron, First Avenue North Viaduct at Thirty-second Street, Birmingham, Jefferson County, AL

9 CFR 3.84 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2014 CFR

2014-01-01

... from becoming soiled, and to reduce disease hazards, insects, pests, and odors. Dirt floors, floors..., such as in a mechanical cage washer; (iii) Washing all soiled surfaces with appropriate detergent... same purpose, with a thorough cleaning of the surfaces to remove organic material, so as to remove all...

9 CFR 3.84 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... from becoming soiled, and to reduce disease hazards, insects, pests, and odors. Dirt floors, floors..., such as in a mechanical cage washer; (iii) Washing all soiled surfaces with appropriate detergent... same purpose, with a thorough cleaning of the surfaces to remove organic material, so as to remove all...

9 CFR 3.84 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... from becoming soiled, and to reduce disease hazards, insects, pests, and odors. Dirt floors, floors..., such as in a mechanical cage washer; (iii) Washing all soiled surfaces with appropriate detergent... same purpose, with a thorough cleaning of the surfaces to remove organic material, so as to remove all...

9 CFR 3.84 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... from becoming soiled, and to reduce disease hazards, insects, pests, and odors. Dirt floors, floors..., such as in a mechanical cage washer; (iii) Washing all soiled surfaces with appropriate detergent... same purpose, with a thorough cleaning of the surfaces to remove organic material, so as to remove all...

9 CFR 3.84 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... from becoming soiled, and to reduce disease hazards, insects, pests, and odors. Dirt floors, floors..., such as in a mechanical cage washer; (iii) Washing all soiled surfaces with appropriate detergent... same purpose, with a thorough cleaning of the surfaces to remove organic material, so as to remove all...

9 CFR 3.11 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2014 CFR

2014-01-01

... prevent an excessive accumulation of feces and food waste, to prevent soiling of the dogs or cats... mechanical cage washer; or (iii) Washing all soiled surfaces with appropriate detergent solutions and... a thorough cleaning of the surfaces to remove organic material, so as to remove all organic material...

9 CFR 3.11 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... prevent an excessive accumulation of feces and food waste, to prevent soiling of the dogs or cats... mechanical cage washer; or (iii) Washing all soiled surfaces with appropriate detergent solutions and... a thorough cleaning of the surfaces to remove organic material, so as to remove all organic material...

9 CFR 3.11 - Cleaning, sanitization, housekeeping, and pest control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... prevent an excessive accumulation of feces and food waste, to prevent soiling of the dogs or cats... mechanical cage washer; or (iii) Washing all soiled surfaces with appropriate detergent solutions and... a thorough cleaning of the surfaces to remove organic material, so as to remove all organic material...

16 CFR 305.20 - Paper catalogs and websites.

Code of Federal Regulations, 2012 CFR

2012-01-01

...] national average electricity cost of [ ___ cents per kWh]. For more information, visit www.ftc.gov... estimated operating cost is based on a [Year] national average [electricity, natural gas, propane, or oil... washers] and a [Year] national average cost of ___ cents per kWh for electricity and $ ___ per therm for...

16 CFR 305.20 - Paper catalogs and websites.

Code of Federal Regulations, 2013 CFR

2013-01-01

...] national average electricity cost of [ ___ cents per kWh]. For more information, visit www.ftc.gov... estimated operating cost is based on a [Year] national average [electricity, natural gas, propane, or oil... washers] and a [Year] national average cost of ___ cents per kWh for electricity and $ ___ per therm for...

77 FR 1082 - Large Residential Washers From Korea and Mexico; Institution of Antidumping and Countervailing...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-09

... United States, and imported under statistical reporting number 8450.20.0090. Products subject to these..., 2012. The Commission's views are due at Commerce within five business days thereafter, or by February.... Limited disclosure of business proprietary information (BPI) under an administrative protective order (APO...

Toward a Safer and Cleaner Way: Dealing With Human Waste in Healthcare.

PubMed

Apple, Michael

2016-07-01

Organizations must evaluate their infection control plans in a holistic and inclusive manner to continue reducing healthcare-associated infection (HAI) rates, including giving consideration to the manner of collecting and disposing of patient waste. Manual washing of bedpans and other containers poses a risk of spreading infection via caregivers, the environment, and the still-contaminated bedpan. Several alternative disposal methods are available and have been tested in some countries for decades, including options such as bedpan washer-disinfector machines, macerator machines, and disposable bedpans. This article reviews methods and issues related to human waste disposal in healthcare settings. Healthcare organizations must evaluate the options thoroughly and then consistently implement the option most in line with its goals and culture. © The Author(s) 2016.

Standard specification for carbon and alloy steel nuts. ASTM standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This specification is under the jurisdiction of ASTM Committee F-16 on Fasteners and is the responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets, and Washers. Current edition approved Dec. 10, 1997. Published July 1998. Originally published as A 563-66. Last previous edition A 563-96.

Reading Polymorphemic Dutch Compounds: Toward a Multiple Route Model of Lexical Processing

ERIC Educational Resources Information Center

Kuperman, Victor; Schreuder, Robert; Bertram, Raymond; Baayen, R. Harald

2009-01-01

This article reports an eye-tracking experiment with 2,500 polymorphemic Dutch compounds presented in isolation for visual lexical decision while readers' eye movements were registered. The authors found evidence that both full forms of compounds ("dishwasher") and their constituent morphemes (e.g., "dish," "washer," "er") and morphological…

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The home that won a Production Builder award in the 2014 Housing Innovation Awards serves as a model for this builder, showcasing high-tech features including an electric car charging station; a compressed natural gas (CNG) car fueling station; a greywater recycling system that filters shower, sink, and clothes washer water for yard irrigation; smart appliances; and an electronic energy management system.

78 FR 16196 - Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-14

... corrugated washer in the middle of the main transmission filter housing upper part and modifying the main... revealed the bypass inlet in the oil filter area was not manufactured in accordance with applicable design... revealed the bypass inlet in the oil filter area had not been manufactured in accordance with the...

77 FR 75975 - Large Residential Washers From the Republic of Korea: Final Affirmative Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... determines that material injury, or threat of material injury, does not exist, this proceeding will be... R&D Program/Information Display R&D Center Program [squf] Support for SME ``Green Partnerships... R&D'' Program Comment 15: Whether the Department Erred in Finding That the ``SME Green Partnerships...

76 FR 40219 - Airworthiness Directives; Various Aircraft Equipped With Rotax Aircraft Engines 912 A Series Engine

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-08

... Airworthiness Directives; Various Aircraft Equipped With Rotax Aircraft Engines 912 A Series Engine AGENCY... installed on a limited number of engines. No defective washers have been shipped as spare parts. This... consequent ignition failure, possibly resulting in damage to the engine, in- flight engine shutdown and...

77 FR 75972 - Foreign-Trade Zone 26 - Atlanta, Georgia Notification of Proposed Production Activity Suzuki Mfg...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-26

... able to choose the duty rate during customs entry procedures that apply to ATVs and related components... include: articles of rubber, hoses, gaskets, washers, fasteners, springs, sign plates/ labels, brackets, plates, braces, fittings, body parts, engines and related parts, pumps, fans, valves, hose/pipe...

26 CFR 48.4218-1 - Tax on use by manufacturer, producer, or importer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the incorporation of a taxable article, such as an electric light bulb, into a nontaxable article... type electric or gas clothes drier incorporated in a combination washer-drier. (b) Household type electric, gas, or oil cooking range combined either with a range using other means of heating or with a...

26 CFR 48.4218-1 - Tax on use by manufacturer, producer, or importer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the incorporation of a taxable article, such as an electric light bulb, into a nontaxable article... type electric or gas clothes drier incorporated in a combination washer-drier. (b) Household type electric, gas, or oil cooking range combined either with a range using other means of heating or with a...

75 FR 59071 - Airworthiness Directives; Bombardier, Inc. Model CL-600-2B16 (CL-604 Variants (Including CL-605...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-27

... turbine imbalance. Such imbalance could potentially result in ADG structural failure (including blade... screw failure on similar ADGs [air-driven generators]/ram air turbines installed on other aircraft types... can result in loss of the related balance washer, with consequent turbine imbalance. Such imbalance...

75 FR 31731 - Airworthiness Directives; Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-04

... turbine imbalance. Such imbalance could potentially result in RAT structural failure (including blade... turbine imbalance. Such imbalance could potentially result in RAT structural failure (including blade... reported cases of balance washer screw failure on similar RATs [ram air turbines]/air driven generators...

10 CFR 431.156 - Energy and water conservation standards and effective dates.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Energy and water conservation standards and effective dates. 431.156 Section 431.156 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Commercial Clothers Washers Energy Conservation Standards § 431.156 Energy and water conservation...

10 CFR 431.156 - Energy and water conservation standards and effective dates.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Energy and water conservation standards and effective dates. 431.156 Section 431.156 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT Commercial Clothers Washers Energy Conservation Standards § 431.156 Energy and water conservation...

49 CFR 583.7 - Procedure for determining major foreign sources of passenger motor vehicle equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., oil, blackout, phosphate rinse, windshield washer fluid, fasteners, tire assembly fluid, rivets... equipment, and the U.S. and Canada are treated together. (d) Determination of the percentage of the total... basis by— (1) Adding up the total value of all of the passenger motor vehicle equipment (regardless of...

49 CFR 583.7 - Procedure for determining major foreign sources of passenger motor vehicle equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., oil, blackout, phosphate rinse, windshield washer fluid, fasteners, tire assembly fluid, rivets... equipment, and the U.S. and Canada are treated together. (d) Determination of the percentage of the total... basis by— (1) Adding up the total value of all of the passenger motor vehicle equipment (regardless of...

49 CFR 583.7 - Procedure for determining major foreign sources of passenger motor vehicle equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., oil, blackout, phosphate rinse, windshield washer fluid, fasteners, tire assembly fluid, rivets... equipment, and the U.S. and Canada are treated together. (d) Determination of the percentage of the total... basis by— (1) Adding up the total value of all of the passenger motor vehicle equipment (regardless of...

49 CFR 583.7 - Procedure for determining major foreign sources of passenger motor vehicle equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., oil, blackout, phosphate rinse, windshield washer fluid, fasteners, tire assembly fluid, rivets... equipment, and the U.S. and Canada are treated together. (d) Determination of the percentage of the total... basis by— (1) Adding up the total value of all of the passenger motor vehicle equipment (regardless of...

16 CFR 305.20 - Paper catalogs and Web sites.

Code of Federal Regulations, 2014 CFR

2014-01-01

... based on a [Year] national average electricity cost of [ ___ cents per kWh]. For more information, visit... estimated operating cost is based on a [Year] national average [electricity, natural gas, propane, or oil... washers] and a [Year] national average cost of ___ cents per kWh for electricity and $ ___ per therm for...

Characterization of a medium-sized washer-gun for an axisymmetric mirror

NASA Astrophysics Data System (ADS)

Yi, Hongshen; Liu, Ming; Shi, Peiyun; Yang, Zhida; Zhu, Guanghui; Lu, Quanming; Sun, Xuan

2018-04-01

A new medium-sized washer gun is developed for a plasma start-up in a fully axisymmetric mirror. The gun is positioned at the east end of the Keda Mirror with AXisymmetricity facility and operated in the pulsed mode with an arc discharging time of 1.2 ms and a typical arc current of 8.5 kA with 1.5 kV discharge voltage. To optimize the operation, a systematic scan of the neutral pressure, the arc voltage, the bias voltage on a mesh grid 6 cm in front of the gun and an end electrode located on the west end of mirror, and the mirror ratio was performed. The streaming plasma was measured with triple probes in the three mirror cells and a diamagnetic loop in the central cell. Floating potential measurements suggest that the plasma could be divided into streaming and mirror-confined plasmas. The floating potential for the streaming plasma is negative, with an electric field pointing inwards. The mirror-confined plasma has a typical lifetime of 0.5 ms.

Development of neutral beam injection system by use of washer gun plasma source

NASA Astrophysics Data System (ADS)

Imanaka, Heizo; Kajiya, Hirotaka; Nemoto, Yuichi; Azuma, Akiyoshi; Asai, Tomoaki; Yamada, Takuma; Inomoto, Michiaki; Ono, Yasushi

2008-11-01

For the past ten years, we have been investigating high-beta Spherical Tokamaks (ST) formation using reconnection heating of their axial merging in the TS-4 experiment, University of Tokyo. The produced ST was observed to have the maximum beta of 50-60% right after the merging of two STs. A key issue after the formation is to maintain the produced high-beta ST over 100 Alfven times for its stability check. A new low-cost pulsed neutral beam injection (NBI) system has been arranged for its sustainment experiment. Its advantages are 1) low voltage (15kV for low-field side of ST) and high current (20A), 2) maintenance-free, 3) low-cost. The conventional filament plasma source was replaced by the washer gun to realize air-cooled and maintenance free NBI system. In its startup experiment, we already extracted the maximum beam current of 3.7A for then acceleration voltage of 10kV successfully. This result suggests that the increase in the acceleration voltage and several conditioning work will realize its designed beam parameters of 15kV, 20A.

Characterization of a medium-sized washer-gun for an axisymmetric mirror.

PubMed

Yi, Hongshen; Liu, Ming; Shi, Peiyun; Yang, Zhida; Zhu, Guanghui; Lu, Quanming; Sun, Xuan

2018-04-01

A new medium-sized washer gun is developed for a plasma start-up in a fully axisymmetric mirror. The gun is positioned at the east end of the Keda Mirror with AXisymmetricity facility and operated in the pulsed mode with an arc discharging time of 1.2 ms and a typical arc current of 8.5 kA with 1.5 kV discharge voltage. To optimize the operation, a systematic scan of the neutral pressure, the arc voltage, the bias voltage on a mesh grid 6 cm in front of the gun and an end electrode located on the west end of mirror, and the mirror ratio was performed. The streaming plasma was measured with triple probes in the three mirror cells and a diamagnetic loop in the central cell. Floating potential measurements suggest that the plasma could be divided into streaming and mirror-confined plasmas. The floating potential for the streaming plasma is negative, with an electric field pointing inwards. The mirror-confined plasma has a typical lifetime of 0.5 ms.

Sanitation in self-service automatic washers.

PubMed Central

Buford, L E; Pickett, M S; Hartman, P A

1977-01-01

The potential for microbial transfer in self-service laundry washing machines was investigated by obtaining swab samples from the interior surfaces of commercial machines and wash water samples before and after disinfectant treatment. Three disinfectants (chlorine, a quaternary ammonium product, and a phenolic disinfectant) were used. Four self-service laundry facilities were sampled, with 10 replications of the procedure for each treatment at each location. Although washers were set on a warmwater setting, the wash water temperatures ranged from 24 to 51 degrees C. The quaternary ammonium product seemed most effective, averaging a 97% microbial kill; chlorine was the second most effective, with a 58% kill, and the phenolic disinfectant was least effective, with only a 25% kill. The efficacies of the chlorine and phenolic disinfectants were reduced at low water temperatures commonly experienced in self-service laundries. Interfamily cross-contamination in self-service facilities is a potential public health problem, which is aggravated by environmental conditions, such as water temperature and the practices of the previous users of the equipment. Procedural changes in laundering are recommended, including the use of a disinfectant to maintain adequate levels of sanitation. PMID:13714

CFD Analysis of Tile-Repair Augers for the Shuttle Orbiter Re-Entry Aeroheating

NASA Technical Reports Server (NTRS)

Mazaheri, Ali R.

2007-01-01

A three-dimensional aerothermodynamic model of the shuttle orbiter's tile overlay repair (TOR) sub-assembly is presented. This sub-assembly, which is an overlay that covers the damaged tiles, is modeled as a protuberance with a constant thickness. The washers and augers that serve as the overlay fasteners are modeled as cylindrical protuberances with constant thicknesses. Entry aerothermodynamic cases are studied to provide necessary inputs for future thermal analyses and to support the space-shuttle return-to-flight effort. The NASA Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) is used to calculate heat transfer rate on the surfaces of the tile overlay repair and augers. Gas flow is modeled as non-equilibrium, five species air in thermal equilibrium. Heat transfer rate and surface temperatures are analyzed and studied for a shuttle orbiter trajectory point at Mach 17.85. Computational results show that the average heat transfer rate normalized with respect to its value at body point 1800 is about BF=1.9 for the auger head. It is also shown that the average BF for the auger and washer heads is about BF=2.0.

A design framework for teleoperators with kinesthetic feedback

NASA Technical Reports Server (NTRS)

Hannaford, Blake

1989-01-01

The application of a hybrid two-port model to teleoperators with force and velocity sensing at the master and slave is presented. The interfaces between human operator and master, and between environment and slave, are ports through which the teleoperator is designed to exchange energy between the operator and the environment. By computing or measuring the input-output properties of this two-port network, the hybrid two-port model of an actual or simulated teleoperator system can be obtained. It is shown that the hybrid model (as opposed to other two-port forms) leads to an intuitive representation of ideal teleoperator performace and applies to several teleoperator architectures. Thus measured values of the h matrix or values computed from a simulation can be used to compare performance with th ideal. The frequency-dependent h matrix is computed from a detailed SPICE model of an actual system, and the method is applied to a proposed architecture.

Silicon materials task of the Low Cost Solar Array Project: Effect of impurities and processing on silicon solar cells

NASA Technical Reports Server (NTRS)

Hopkins, R. H.; Davis, J. R.; Rohatgi, A.; Hanes, M. H.; Rai-Choudhury, P.; Mollenkopf, H. C.

1982-01-01

The effects of impurities and processing on the characteristics of silicon and terrestrial silicon solar cells were defined in order to develop cost benefit relationships for the use of cheaper, less pure solar grades of silicon. The amount of concentrations of commonly encountered impurities that can be tolerated in typical p or n base solar cells was established, then a preliminary analytical model from which the cell performance could be projected depending on the kinds and amounts of contaminants in the silicon base material was developed. The impurity data base was expanded to include construction materials, and the impurity performace model was refined to account for additional effects such as base resistivity, grain boundary interactions, thermal processing, synergic behavior, and nonuniform impurity distributions. A preliminary assessment of long term (aging) behavior of impurities was also undertaken.

Comparing depth-dependent curing radiant exposure and time of curing of regular and flow bulk-fill composites.

PubMed

Rodrigues, Jose Augusto; Tenorio, Ilana Pais; Mello, Ginger Baranhuk Rabello de; Reis, André Figueiredo; Shen, Chiayi; Roulet, Jean-François

2017-08-21

The effect of restoration depth on the curing time of a conventional and two bulk-fill composite resins by measuring microhardness and the respective radiosity of the bottom surface of the specimen was investigated. 1-, 3- and 5-mm thick washers were filled with Surefil SDR Flow-U (SDR), Tetric EvoCeram Bulk Fill-IVA (TEC) or Esthet-X HD-B1 (EHD), and cured with Bluephase® G2 for 40s. Additional 1-mm washers were filled with SDR, TEC or EHD, placed above the light sensor of MARC®, stacked with pre-cured 1-, 3- or 5-mm washer of respective material, and cured for 2.5~60s to mimic 2-, 4- and 6-mm thick composite curing. The sensor measured the radiosity (EB) at the bottom of specimen stacks. Vickers hardness (VH) was measured immediately at 5 locations with triplicate specimens. Nonlinear regression of VH vs EB by VH=α[1-exp(-EB/β)] with all thickness shows that the values of α, maximum hardness, are 21.6±1.0 kg/mm2 for SDR, 38.3±0.6 kg/mm2 for TEC and 45.3±2.6 kg/mm2 for EHD, and the values of β, rate parameter, are 0.40±0.06 J/cm2 for SDR, 0.77±0.04 J/cm2 for TEC and 0.58±0.09 J/cm2 for EHD. The radiosity of the bottom surface was calculated when the bottom surface of each material attained 80% of α of each material. The curing times for each material are in agreement with manufacturer recommendation for thickness. It is possible to estimate time needed to cure composite resin of known depth adequately by the radiosity and microhardness of the bottom surface.

Standardized system for quantifying residual dirt on medical appliances cleansed in hospital washers--disinfectors: dirt detection by different methods.

PubMed

Sigler, K; Gásková, D; Chládková, K; Knebl, R; Wimmer, T; Vacata, V; Gebel, J

2003-01-01

An easy-to construct, easy-to-operate standardized system was developed for determining the residual biological contamination of surgical instruments, endoscopes and other medical appliances subjected to hospital cleansing and/or disinfection. It consists of standard-sized pieces of glass, metal or endoscope plastic--dirt carriers--either bare or enclosed in truncated Eppendorf caps to simulate hard-to-access conditions. The surface of the carriers is covered with model dirt simulating biological contamination and the carriers are then affixed to sturdy metal holders. Conventional model dirt were found to peel or flake off the carrier surface, lowering the precision of residual soil determination. A newly developed model dirt consisting of liver mash, lactose and sunflower oil and exhibiting low tendency to peel off surfaces was therefore used. The whole setup was subjected to chemical or enzymic cleansing programs at elevated temperature in hospital washer-disinfectors of two types, and the residual dirt after cleansing was determined by three methods. The method using toxicant-doped dirt that quenches the luminescence of an indicator bacterium Photobacterium phosphoreum gave satisfactory data under laboratory conditions but with hospital-washed samples it exhibited excessive fluctuations caused by bacterium--dirt interactions and by physical influences. Both other methods gave better results but displayed some process sensitivity. The luciferin-luciferase-based ATP bioluminescence assay sometimes gave low or even negative dirt level values and showed a low effect of reduced dirt accessibility on cleansing of metal carriers. The Bradford protein assay showed about equal cleansing efficiency for both easily and poorly accessible carriers after enzymic cleansing. Our system can be used for determining low levels of residual contamination of medical appliances after cleansing/disinfection and assessing the efficiency of commercial washer-disinfectors; its efficiency can be further increased by using a cleansing process-insensitive method for soil detection and quantification.

Dual-Enhanced Photocatalytic Activity of Fe-Deposited Titanate Nanotubes Used for Simultaneous Removal of As(III) and As(V).

PubMed

Liu, Wen; Zhao, Xiao; Borthwick, Alistair G L; Wang, Yanqi; Ni, Jinren

2015-09-09

Fe-deposited titanate nanotubes (Fe-TNTs) with high photocatalytic activity and adsorptive performance were synthesized through a one-step hydrothermal method. Initial As(III) oxidation followed by As(V) adsorption by Fe-TNTs could simultaneously remove these two toxic pollutants from aqueous solutions. The apparent rate constant value for photo-oxidation of As(III) under UV irradiation by Fe-TNTs was almost 250 times that of unmoidified TNTs. Under visible light, the Fe-TNTs also exhibited enhanced photocatalytic activity after Fe was deposited. Fe3+ located in the interlayers of TNTs acted as temporary electron- or hole-trapping sites, and attached α-Fe2O3 played the role of a charge carrier for electrons transferred from TNTs. These two effects inhibited electron-hole pair recombination thus promoting photocatalysis. Moreover, the As(V) adsorptive performance of Fe-TNTs also improved, owing to the presence of additional adsorption sites, α-Fe2O3, as well as increased pHPZC. Furthermore, Fe-TNTs exhibited good photocatalytic and adsorptive performace even after 5 reuse cycles. The present tests, concerning an initial As(III) photocatalysis and subsequent As(V) adsorption process, highlight the feasibility and importance of Fe used to modify TNTs. This study proposes a feasible method to simultaneously remove As(III) and As(V) from contaminated water using a novel Ti-based nanomaterial.

76 FR 20503 - Airworthiness Directives; Empresa Brasileira de Aeronautica S.A. (EMBRAER) Model ERJ 170 and ERJ...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

... of the related balance washer causing a possible ram air turbine (RAT) imbalance event, which may... in loss of power to airplane flight controls hydraulic back-up system. * * * * * Loss of power to the hydraulic back-up system for airplane flight controls could reduce the ability of the flightcrew to maintain...

76 FR 31465 - Airworthiness Directives; Various Aircraft Equipped With Rotax Aircraft Engines 912 A Series Engine

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

... has been detected, which exceeds the hardness of the design specification. The affected washers are... Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590. Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor...

46 CFR 160.115-7 - Design, construction, and performance of winches.

Code of Federal Regulations, 2012 CFR

2012-10-01

... requirements: (1) Materials. (i) All gears must be machine cut and made of steel, bronze, or other suitable... suitable lock washers, cotter pins, or locks to prevent them from coming adrift. (2) Bearings and gears. (i) Positive means of lubrication must be provided for all bearings. (ii) When worm gears are used, the worm...

77 FR 4007 - Large Residential Washers From the Republic of Korea and Mexico: Initiation of Antidumping Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-26

... the electronic submission requirements must be filed manually (i.e., in paper form) with the Import... Investigations,'' in Appendix I of this notice. Comments on Scope of Investigations During our review of the... this requirement if the domestic producers or workers who support the petition account for: (i) At...

77 FR 33181 - Large Residential Washers From the Republic of Korea: Preliminary Affirmative Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-05

... does not include a rate for either the ``Korea Trade Insurance Corporation (K-SURE)-- Short-Term Export.... C. Benchmark Interest Rate for Short-Term Loans Section 771(5)(E)(ii) of the Act states that the... Development Bank (KDB)/IBK Short-Term Discounted Loans for Export Receivables'' program, an analysis of any...

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacLachlan, J.A.

The basic premises of the conceptual design for the linac upgrade are pursued to establish lengths, gradients, power dissipation, etc., for the 400 MeV linac and matching section. The discussion is limited to accelerating and focusing components. Wherever values depend on the choice of the accelerating structure, the disk-and-washer structure is emphasized; the results are generally relevant to the side coupled cavity choice also.

76 FR 31629 - Helical Spring Lock Washers From China and Taiwan; Institution of Five-Year Reviews Concerning...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

... conditions or business cycle for the Domestic Like Product that have occurred in the United States or in the... disclosure of business proprietary information (BPI) under an administrative protective order (APO) and APO... This Notice Of Institution: If you are a domestic producer, union/worker group, or trade/business...

75 FR 57937 - Energy Conservation Program for Consumer Products: Notice of Petition for Waiver of Samsung...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-23

... determining the energy consumption of clothes washers. Today's notice also grants an interim waiver of the... evaluate the basic model in a manner so unrepresentative of its true energy consumption characteristics as... manner representative of its energy consumption. 10 CFR 430.27(b)(1)(iii). The Assistant Secretary may...

77 FR 32381 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-31

... year used for discounting the NPV of total consumer costs and savings, for the time-series of costs and... does not imply that the time-series of cost and benefits from which the annualized values were..., engineering resources, and other conversion activities over a longer period of time depending on the [[Page...

77 FR 17029 - Certain Steel Nails From the United Arab Emirates: Final Determination of Sales at Less Than Fair...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-23

... coils using materials such as plastic, paper, or wire. Certain steel nails subject to this investigation... plastic or steel washers (``caps'') already assembled to the nail, having a bright or galvanized finish, a... Initiation Notice,\\2\\ by removing the language referring to the packaging characteristics of certain nails...

7. INTERIOR, ROBERTS AND SCHAEFER SHAKER TABLE (LEFT), MARYLAND NEW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. INTERIOR, ROBERTS AND SCHAEFER SHAKER TABLE (LEFT), MARYLAND NEW RIVER COAL COMPANY INSTALLED APRON CONVEYOR (RIGHT) USED TO CONVEY COAL TO THE BELKNAP CHORIDE WASHER, RETURN CHUTE FOR CLEANED COAL (FAR RIGHT), AND COAL STORAGE SILO (BACKGROUND), LOOKING WEST - Nuttallburg Mine Complex, Tipple, North side of New River, 2.7 miles upstream from Fayette Landing, Lookout, Fayette County, WV

76 FR 64330 - Notice of Petition for Waiver of LG Electronics U.S.A., Inc. From the Department of Energy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-18

... Petition for Waiver of LG Electronics U.S.A., Inc. From the Department of Energy Residential Clothes Washer... for comments. SUMMARY: This notice announces receipt of and publishes the LG Electronics U.S.A., Inc..., Government Relations and Communications, LG Electronics USA, Inc., 1776 K Street, NW., Washington, DC 20006...

Dumbo: A pachydermal rocket motor

NASA Technical Reports Server (NTRS)

Kirk, Bill

1991-01-01

A brief historical account is given of the Dumbo nuclear reactor, a type of folded flow reactor that could be used for rocket propulsion. Much of the information is given in viewgraph form. Viewgraphs show details of the reactor system, fuel geometry, and key characteristics of the system (folded flow, use of fuel washers, large flow area, small fuel volume, hybrid modulator, and cermet fuel).

78 FR 69989 - Airworthiness Directives; Eurocopter France Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-22

... and that air safety and the public interest require adopting the AD requirements as proposed... joint nut and washer within 165 hours TIS. In addition, this AD does not apply to the Model AS350BB as... Eurocopter has issued Alert Service Bulletin (ASB) No. AS350- 52.00.34 for Model AS350 B, B1, B2, B3, BA, BB...

75 FR 1297 - Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-11

... installed, one-time torquing of the nut and bolt, and corrective actions if necessary. This proposed AD... nut and bolt, and corrective actions if necessary. That AD resulted from reports of parts coming off... of the slat track hardware (i.e., the bolt, washers, downstops, stop location, and nut shown in...

Standard specification for anchor bolts, steel, 36, 55, and 105-ksi yield strength. ASTM standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-07-01

This specification is under the jurisdiction of ASTM Committee F-16 on Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets, and Washers. Current edition approved Dec. 10, 1997 and published July 1998. Originally published as F 1554-94. Last previous edition was F 1554-94.

Electrical Connector for Graphite Heating Elements

NASA Technical Reports Server (NTRS)

Mackintosh, B. H.

1982-01-01

Connection method applies force to two interfaces: that between heating element proper and heating-element support members and between heating-element support members and metal conductor. Inner rod of new connector system is maintained in tension by a spring (for example, Belleville washers). Connection is sufficiently complaint so tension remains within desired range, regardless of thermal expansion and contraction of various elements.

Examination of Surveyor 3 parts with the scanning electron microscope and electron microprobe

NASA Technical Reports Server (NTRS)

Chodos, A. A.; Devaney, J. R.; Evens, K. C.

1972-01-01

Two screws and two washers, several small chips of tubing, and a fiber removed from a third screw were examined with the scanning electron microscope and the electron microprobe. The purpose of the examination was to determine the nature of the material on the surface of these samples and to search for the presence of meteoritic material.

77 FR 4279 - Large Residential Washers From the Republic of Korea: Initiation of Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-27

... the electronic submission requirements must be filed manually (i.e., in paper form) with the Import... 2011, i.e., January 1, 2011, through December 31, 2011. See 19 CFR 351.204(b)(2). Scope of the... or workers who support the petition account for: (i) At least 25 percent of the total production of...

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., plates, or washers, need not have such hardware, but shall have 7/16-20 UNF-2A or 1/2-13 UNC-2A... and other parts from becoming disengaged from the vehicle while in service. Reinforcing plates or... projected area. The distance between any edge of the plate and the edge of the bolt hole shall be at least...

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., plates, or washers, need not have such hardware, but shall have 7/16-20 UNF-2A or 1/2-13 UNC-2A... and other parts from becoming disengaged from the vehicle while in service. Reinforcing plates or... projected area. The distance between any edge of the plate and the edge of the bolt hole shall be at least...

49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., plates, or washers, need not have such hardware, but shall have 7/16-20 UNF-2A or 1/2-13 UNC-2A... and other parts from becoming disengaged from the vehicle while in service. Reinforcing plates or... projected area. The distance between any edge of the plate and the edge of the bolt hole shall be at least...

78 FR 11148 - Large Residential Washers From Mexico and the Republic of Korea: Antidumping Duty Orders

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-15

... contains payment system electronics; \\7\\ (b) it is configured with an externally mounted steel frame at... drying machines that are built on a unitary frame and share a common console that controls both the... selected wash cycle setting; and (d) the console containing the user interface is made of steel and is...

77 FR 46715 - Large Residential Washers From the Republic of Korea: Amendment to the Scope of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-06

... contains payment system electronics; \\12\\ (b) it is configured with an externally mounted steel frame at... distinct washing and drying machines that are built on a unitary frame and share a common console that... wash cycle setting; and (d) the console containing the user interface is made of steel and is assembled...

Improved Thermal-Switch Disks Protect Batteries

NASA Technical Reports Server (NTRS)

Darcy, Eric; Bragg, Bobby

1990-01-01

Improved thermal-switch disks help protect electrical batteries against high currents like those due to short circuits or high demands for power in circuits supplied by batteries. Protects batteries against excessive temperatures. Centered by insulating fiberglass washer. Contains conductive polymer that undergoes abrupt increase in electrical resistance when excessive current raises its temperature above specific point. After cooling, polymer reverts to low resistance. Disks reusable.

Automated decontamination of surface-adherent prions.

PubMed

Schmitt, A; Westner, I M; Reznicek, L; Michels, W; Mitteregger, G; Kretzschmar, H A

2010-09-01

At present there is no routinely available decontamination procedure in washer-disinfectors to allow the reliable inactivation and/or elimination of prions present on reusable surgical instruments. This means that is not possible to provide assurance for preventing iatrogenic transmission of prion diseases. We need effective procedures in prion decontamination that can be integrated into the usual routine of reprocessing surgical instruments. This article reports on the evaluation of an automated process designed to decontaminate prions in washer-disinfectors using a quantitative, highly sensitive in vivo assay for surface-adherent 22L prions. The automated process showed great advantages when compared with conventional alkaline cleaning. In contrast, the new process was as effective as autoclaving at 134 degrees C for 2h and left no detectable prion infectivity, even for heavily contaminated surfaces. This indicates a reduction of surface-adherent prion infectivity of >7 log units. Due to its compatibility with even delicate surgical instruments, the process can be integrated into the large scale reprocessing of instruments in a central sterile supply department. The system could potentially make an important contribution to the prevention of iatrogenic transmission of prions. Copyright 2010 The Hospital Infection Society. Published by Elsevier Ltd. All rights reserved.

Sensor 17 Thermal Isolation Mounting Structure (TIMS) Design Improvements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Enstrom, K.

2015-09-04

The SENSOR 17 thermographic camera weighs approximately 0.5lbs, has a fundamental mode of 167 Hz, and experiences 0.75W of heat leakage in through the TIMS. The configuration, shown in Figure 1, is comprised of four 300 Series SST washers paired in tandem with P.E.I (Ultem 100) washers. The SENSOR 17 sensor is mounted to a 300 series stainless plate with A-shaped arms. The Plate can be assumed to be at ambient temperatures (≈293K) and the I.R. Mount needs to be cooled to 45K. It is attached to the tip of a cryocooler by a ‘cold strap’ and is assumed tomore » be at the temperature of the cold-strap (≈45K). During flights SENSOR 17 experiences excitations at frequencies centered around 10-30Hz, 60Hz, and 120Hz from the aircraft flight environment. The temporal progression described below depicts the 1st Modal shape at the systems resonant frequency. This simulation indicates Modal articulation will cause a pitch rate of the camera with respect to the body axis of the airplane. This articulation shows up as flutter in the camera.« less

Design and 3D simulation of a two-cavity wide-gap relativistic klystron amplifier with high power injection

NASA Astrophysics Data System (ADS)

Bai, Xianchen; Yang, Jianhua; Zhang, Jiande

2012-08-01

By using an electromagnetic particle-in-cell (PIC) code, an S-band two-cavity wide-gap klystron amplifier (WKA) loaded with washers/rods structure is designed and investigated for high power injection application. Influences of the washers/rods structure on the high frequency characteristics and the basic operation of the amplifier are presented. Generally, the rod structure has great impacts on the space-charge potential depression and the resonant frequency of the cavities. Nevertheless, if only the resonant frequency is tuned to the desired operation frequency, effects of the rod size on the basic operation of the amplifier are expected to be very weak. The 3-dimension (3-D) PIC simulation results show an output power of 0.98 GW corresponding to an efficiency of 33% for the WKA, with a 594 keV, 5 kA electron beam guided by an external magnetic field of 1.5 Tesla. Moreover, if a conductive plane is placed near the output gap, such as the electron collector, the beam potential energy can be further released, and the RF power can be increased to about 1.07 GW with the conversion efficiency of about 36%.

Wedge assembly for electrical transformer component spacing

DOEpatents

Baggett, Franklin E.; Cage, W. Franklin

1991-01-01

A wedge assembly that is easily inserted between two surfaces to be supported thereby, and thereafter expanded to produce a selected spacing between those surfaces. This wedge assembly has two outer members that are substantially identical except that they are mirror images of each other. Oppositely directed faces of these of these outer members are substantially parallel for the purpose of contacting the surfaces to be separated. The outer faces of these outer members that are directed toward each other are tapered so as to contact a center member having complementary tapers on both faces. A washer member is provided to contact a common end of the outer members, and a bolt member penetrates this washer and is threadably received in a receptor of the center member. As the bolt member is threaded into the center member, the center member is drawn further into the gap between the outer members and thereby separates these outer members to contact the surfaces to be separated. In the preferred embodiment, the contacting surfaces of the outer member and the center member are provided with guide elements. The wedge assembly is described for use in separating the secondary windings from the laminations of an electrical power transformer.

Self-disinfecting plastics for intravenous catheters and prosthetic inserts.

PubMed Central

Kingston, D.; Seal, D. V.; Hill, I. D.

1986-01-01

A disinfectant (2,4,4'-trichloro-2'-hydroxydiphenyl ether: Irgasan, Ciba-Geigy) was incorporated into plastic washers fabricated from ethylvinyl acetate (EVA), polyethylene, polypropylene or TPX. Plastics containing 0.2 and 2% Irgasan gave zones of inhibition on nutrient and blood agar plates seeded with micro-organisms (Staphylococcus aureus, Staph. epidermidis, Escherichia coli, Proteus mirabilis or Candida albicans) even after thorough washing. Exceptionally, C. albicans was inhibited only by 2% Irgasan, and EVA gave good inhibition only against the staphylococci. Similar washers of each plastic were implanted subcutaneously into the flanks of rabbits; before insertion each was washed, had thread woven into it and was surrounded by a plasma clot containing 2 X 10(8) Staph. aureus. All the plastics without Irgasan gave rise to abscesses, none of the plastics impregnated with 2% Irgasan did, though from 2 out of 12 sites small numbers of Staph. aureus were isolated at post mortem. Using either clinical or bacteriological criteria, the results were highly significant (P less than 0.00001 and P less than 0.001 respectively), demonstrating the effectiveness of this technique in preventing plastic-associated infection. Images Fig. 2 Fig. 2(Contd.) PMID:3517154

Rover imaging system for the Mars rover/sample return mission

NASA Technical Reports Server (NTRS)

1993-01-01

In the past year, the conceptual design of a panoramic imager for the Mars Environmental Survey (MESUR) Pathfinder was finished. A prototype camera was built and its performace in the laboratory was tested. The performance of this camera was excellent. Based on this work, we have recently proposed a small, lightweight, rugged, and highly capable Mars Surface Imager (MSI) instrument for the MESUR Pathfinder mission. A key aspect of our approach to optimization of the MSI design is that we treat image gathering, coding, and restoration as a whole, rather than as separate and independent tasks. Our approach leads to higher image quality, especially in the representation of fine detail with good contrast and clarity, without increasing either the complexity of the camera or the amount of data transmission. We have made significant progress over the past year in both the overall MSI system design and in the detailed design of the MSI optics. We have taken a simple panoramic camera and have upgraded it substantially to become a prototype of the MSI flight instrument. The most recent version of the camera utilizes miniature wide-angle optics that image directly onto a 3-color, 2096-element CCD line array. There are several data-taking modes, providing resolution as high as 0.3 mrad/pixel. Analysis tasks that were performed or that are underway with the test data from the prototype camera include the following: construction of 3-D models of imaged scenes from stereo data, first for controlled scenes and later for field scenes; and checks on geometric fidelity, including alignment errors, mast vibration, and oscillation in the drive system. We have outlined a number of tasks planned for Fiscal Year '93 in order to prepare us for submission of a flight instrument proposal for MESUR Pathfinder.

Loglines. May - June 2011

DTIC Science & Technology

2011-06-01

chief of the Aerial Delivery and Textile Section. When orders for construction material peaked in 2010, the riggers helped pack about 200 air...ensures effective inspection programs and that SRM projects are scheduled to ensure critical defense missions can be fueled while the projects are...the Active Item Walk and Pick helps distribution workers quickly grab any of 8,000 items considered fast movers, such as washers and gaskets

77 FR 58338 - Trade Regulation Rule on Care Labeling of Textile Wearing Apparel and Certain Piece Goods

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-20

... 423.6(a) and (b). \\2\\ 16 CFR 423.6(c). \\3\\ The Rule provides that the symbol system developed by ASTM..., that it is ``a system of cleaning by means of equipment consisting of a computer-controlled washer and... GINETEX (83), which is responsible for the care labeling system used in European countries. \\17\\ The...

77 FR 32307 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-31

... today's final rule will be required on March 7, 2015 and January 1, 2018, as set forth in Table I.1 in... information that is exempt from public disclosure. A link to the docket web page can be found at: www.regulations.gov/#!docketDetail ;D=EERE-2008-BT-STD-0019. The regulations.gov web page contains instructions on...

50. Photocopy of photograph (original negative is property of the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

50. Photocopy of photograph (original negative is property of the Central Connecticut Regional Water Authority and preserved in their archives at 90 Sargent Drive, New Haven, Connecticut 06511-5966), photographer unknown, circa 1959. The sand washer designed by New Haven Water Company. - Lake Whitney Water Filtration Plant, Filtration Plant, South side of Armory Street between Edgehill Road & Whitney Avenue, Hamden, New Haven County, CT

Application of chemical dehumidification system to a roof fan house at Michoud Assembly Facility at New Orleans, Louisiana

NASA Technical Reports Server (NTRS)

1976-01-01

The feasibility of a chemical dehumidification system to reduce the energy consumption associated with dehumidification of the chilled air is assessed. A comparative energy consumption and cost analysis of the chemical dehumidification and existing systems and the savings offered by the proposed chemical dehumidification system over the existing air washer-reheat system are presented.

Evaluation of Waste Heat Recovery and Utilization from Residential Appliances and Fixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomlinson, John J; Christian, Jeff; Gehl, Anthony C

Executive Summary In every home irrespective of its size, location, age, or efficiency, heat in the form of drainwater or dryer exhaust is wasted. Although from a waste stream, this energy has the potential for being captured, possibly stored, and then reused for preheating hot water or air thereby saving operating costs to the homeowner. In applications such as a shower and possibly a dryer, waste heat is produced at the same time as energy is used, so that a heat exchanger to capture the waste energy and return it to the supply is all that is needed. In othermore » applications such as capturing the energy in drainwater from a tub, dishwasher, or washing machine, the availability of waste heat might not coincide with an immediate use for energy, and consequently a heat exchanger system with heat storage capacity (i.e. a regenerator) would be necessary. This study describes a two-house experimental evaluation of a system designed to capture waste heat from the shower, dishwasher clothes washer and dryer, and to use this waste heat to offset some of the hot water energy needs of the house. Although each house was unoccupied, they were fitted with equipment that would completely simulate the heat loads and behavior of human occupants including operating the appliances and fixtures on a demand schedule identical to Building American protocol (Hendron, 2009). The heat recovery system combined (1) a gravity-film heat exchanger (GFX) installed in a vertical section of drainline, (2) a heat exchanger for capturing dryer exhaust heat, (3) a preheat tank for storing the captured heat, and (4) a small recirculation pump and controls, so that the system could be operated anytime that waste heat from the shower, dishwasher, clothes washer and dryer, and in any combination was produced. The study found capturing energy from the dishwasher and clothes washer to be a challenge since those two appliances dump waste water over a short time interval. Controls based on the status of the dump valve on these two appliances would have eliminated uncertainty in knowing when waste water was flowing and the recovery system operated. The study also suggested that capture of dryer exhaust heat to heat incoming air to the dryer should be examined as an alternative to using drying exhaust energy for water heating. The study found that over a 6-week test period, the system in each house was able to recover on average approximately 3000 W-h of waste heat daily from these appliance and showers with slightly less on simulated weekdays and slightly more on simulated weekends which were heavy wash/dry days. Most of these energy savings were due to the shower/GFX operation, and the least savings were for the dishwasher/GFX operation. Overall, the value of the 3000 W-h of displaced energy would have been $0.27/day based on an electricity price of $.09/kWh. Although small for today s convention house, these savings are significant for a home designed to approach maximum affordable efficiency where daily operating costs for the whole house are less than a dollar per day. In 2010 the actual measured cost of energy in one of the simulated occupancy houses which waste heat recovery testing was undertaken was $0.77/day.« less

A comparative study of the time performance between NINO and FlexToT ASICs

NASA Astrophysics Data System (ADS)

Sarasola, I.; Nemallapudi, M. V.; Gundacker, S.; Sánchez, D.; Gascón, D.; Rato, P.; Marín, J.; Auffray, E.

2017-04-01

Universitat de Barcelona (UB) and CIEMAT have designed the FlexToT ASIC for the front-end readout of SiPM-based scintillator detectors. This ASIC is aimed at time of flight (ToF) positron emission tomography (PET) applications. In this work we have evaluated the time performance of the FlexToT v2 ASIC compared to the NINO ASIC, a fast ASIC developped at CERN. NINO electronics give 64 ps sigma for single-photon time resolution (SPTR) and 93 ps FWHM for coincidence time resolution (CTR) with 2 × 2 × 5 mm3 LSO:Ce,Ca crystals and S13360-3050CS SiPMs. Using the same SiPMs and crystals, the FlexToT v2 ASIC yields 91 ps sigma for SPTR and 123 ps FWHM for CTR. Despite worse time performace than NINO, FlexToT v2 features lower power consumption (11 vs. 27 mW/ch) and linear ToT energy measurement.

The effects of kinesiotape on athletic-based performance outcomes in healthy, active individuals: a literature synthesis

PubMed Central

Drouin, Jillian L.; McAlpine, Caitlin T.; Primak, Kari A.; Kissel, Jaclyn

2013-01-01

Context: The effect of the application of kinesiotape to skin overlying musculature on measurable athletic-based performance outcomes in healthy individuals has not been well established. Objective: To systematically search and assess the quality of the literature on the effect of kinesiotape on athletic-based performance outcomes in healthy, active individuals. Methods: An electronic search strategy was conducted in MANTIS, Cochrane Library and EBSCO databases. Retrieved articles that met the eligibility criteria were rated for methodological quality by using an adaption of the critical appraisal criteria in Clinical Epidemiology by Sackett et al. Results: Ten articles met the inclusion criteria. Seven articles had positive results in at least one athletic-based performance measure compared to controls. Conclusion: Evidence is lacking to support the use of kinesiotape as a successful measure for improving athletic-based performance outcomes in healthy individuals. However, there is no evidence to show that kinesiotape has a negative effect on any of the performace measures. PMID:24302784

Imaging characterization of a new gamma ray detector based on CRY019 scintillation crystal for PET and SPECT applications

NASA Astrophysics Data System (ADS)

Polito, C.; Pani, R.; Trigila, C.; Cinti, M. N.; Fabbri, A.; Frantellizzi, V.; De Vincentis, G.; Pellegrini, R.; Pani, R.

2017-02-01

In the last 40 years, in the field of Molecular Medicine imaging there has been a huge growth in the employment and in the improvement of detectors for PET and SPECT applications in order to reach accurate diagnosis of the diseases. The most important feature required to these detectors is an high quality of images that is usually obtained benefitting from the development of a wide number of new scintillation crystals with high imaging performances. In this contest, features like high detection efficiency, short decay time, great spectral match with photodetectors, absence of afterglow and low costs are surely attractive. However, there are other factors playing an important role in the realization of high quality images such as energy and spatial resolutions, position linearity and contrast resolution. With the aim to realize an high performace gamma ray detector for PET and SPECT applications, this work is focused on the evaluation of the imaging characteristics of a recently developed scintillation crystal, CRY019.

A Hybrid Demand Response Simulator Version 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

2012-05-02

A hybrid demand response simulator is developed to test different control algorithms for centralized and distributed demand response (DR) programs in a small distribution power grid. The HDRS is designed to model a wide variety of DR services such as peak having, load shifting, arbitrage, spinning reserves, load following, regulation, emergency load shedding, etc. The HDRS does not model the dynamic behaviors of the loads, rather, it simulates the load scheduling and dispatch process. The load models include TCAs (water heaters, air conditioners, refrigerators, freezers, etc) and non-TCAs (lighting, washer, dishwasher, etc.) The ambient temperature changes, thermal resistance, capacitance, andmore » the unit control logics can be modeled for TCA loads. The use patterns of the non-TCA can be modeled by probability of use and probabilistic durations. Some of the communication network characteristics, such as delays and errors, can also be modeled. Most importantly, because the simulator is modular and greatly simplified the thermal models for TCA loads, it is very easy and fast to be used to test and validate different control algorithms in a simulated environment.« less

Design, fabrication and acceptance testing of a zero gravity whole body shower, volume 1

NASA Technical Reports Server (NTRS)

1973-01-01

The effort to design whole body shower for the space station prototype is reported. Clothes and dish washer/dryer concepts were formulated with consideration given to integrating such a system with the overall shower design. Water recycling methods to effect vehicle weight savings were investigated and it was concluded that reusing wash and/or rinse water resulted in weight savings which were not sufficient to outweigh the added degree of hardware complexity. The formulation of preliminary and final designs for the shower are described. A detailed comparison of the air drag vs. vacuum pickup method was prepared that indicated the air drag concept results in more severe space station weight penalties; therefore, the preliminary system design was based on utilizing the vacuum pickup method. Tests were performed to determine the optimum methods of storing, heating and sterilizing the cleansing agent utilized in the shower; it was concluded that individual packages of pre-sterilized cleansing agent should be used. Integration features with the space station prototype system were defined and incorporated into the shower design as necessary.

48. Photocopy of photograph (original negative is property of the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

48. Photocopy of photograph (original negative is property of the Central Connecticut Regional Water Authority and preserved in their archives at 90 Sargent Drive, New Haven, Connecticut 06511-5966), photographer unknown, circa 1935. Loading dirty sand into an ejector for transport to the sand washer. - Lake Whitney Water Filtration Plant, Filtration Plant, South side of Armory Street between Edgehill Road & Whitney Avenue, Hamden, New Haven County, CT

Spit-Hole Effects on the Ballistics of a 7.62-mm Cartridge

DTIC Science & Technology

2014-02-01

barrel retains 0.50 in (12.7 mm) of rifling. The midchamber pressure transducer, Kistler Model 6215 (8), is consistent with previous experiments...Nemours and Company. 2 Kistler Model 9031A Load Washer (9). Force transducer selection was driven by the anticipated load and the necessity of an...Development and Engineering Center, Picatinny Arsenal, NJ, January 1986. 8. Kistler Operating Instructions, Quartz High-Pressure Sensor Type 6215

ACES. Accelerated Corrosion Expert Simulator

DTIC Science & Technology

2010-02-01

Composites Coating Systems Organic Inorganic Ceramic Materials 22 Inputs and Dimensions Xi Thickness Hardness Strength Ductility Abrasion Resistance...GPU 25 T-Handle Latch 10-Year ACT Material/ Coating Configuration Die Cast Zinc T-Handle Carbon Steel Pin CS Shank CS T-Washer Carbon Steel Dish E- coat ...CARC Zinc Plating Cadmium Plated BoltE- coat /CARC CS Panel CS Panel O-Ring E- coat /CARC Original (10-year ACT) Design Green Flag Color Qualitative

Automated Setup Assembly Mechanisms for the Intelligent Machining Workstation

DTIC Science & Technology

1990-11-01

Autoimated analysis systems such as [36,37] use the Finite Elements Method ( FEM ) to evaluate or synthesize the structures of fixtures and workpiece...the angular orientation is not altered, and vice versa. This decoupling is accomplished by elastomers that are quite stiff in compression while being...Larger pins (#14), along with elastomers (#15), and the bolt and washer assembly (#6), provide compliance between top and bottom plate (#2), and by

Hazardous Waste Minimization Assessment: Fort Ord, CA

DTIC Science & Technology

1991-06-01

on microorganisms ( bacteria , fungi, etc.) to decompose and/or bioaccumulate the contaminants in wastes. As a HAZMIN technique, treatment, unlike source...washer X San Jose, CA manufacturer Kinsbursky Bros. Supply (714) 738-8516 North Lemon Street Recycler, Spent batteries x Anaheim. CA 92801 Lubrication Co...0863 2190 Main Street Processor X X San Diego, CA 92113 Pepper Oil Company. Inc. (619) 477-9336 2300 Tidelands Avenue Processor X X National City, CA

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1LIGHT THREE PANEL WOOD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1-LIGHT THREE PANEL WOOD OUTSIDE DOOR SOUTH SIDE OF HOUSE, PLUMBING HOOKUPS FOR WASHER BELOW BUILT-IN CABINETS AT PHOTO LEFT, AND PAIRED ARRANGEMENTS OF 4-LIGHT OVER 4-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS ON SOUTH AND WEST WALLS. VIEW TO SOUTH. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Jacketed lamp bulb envelope

DOEpatents

MacLennan, Donald A.; Turner, Brian P.; Gitsevich, Aleksandr; Bass, Gary K.; Dolan, James T.; Kipling, Kent; Kirkpatrick, Douglas A.; Leng, Yongzhang; Levin, Izrail; Roy, Robert J.; Shanks, Bruce; Smith, Malcolm; Trimble, William C.; Tsai, Peter

2001-01-01

A jacketed lamp bulb envelope includes a ceramic cup having an open end and a partially closed end, the partially closed end defining an aperture, a lamp bulb positioned inside the ceramic cup abutting the aperture, and a reflective ceramic material at least partially covering a portion of the bulb not abutting the aperture. The reflective ceramic material may substantially fill an interior volume of the ceramic cup not occupied by the bulb. The ceramic cup may include a structural feature for aiding in alignment of the jacketed lamp bulb envelope in a lamp. The ceramic cup may include an external flange about a periphery thereof. One example of a jacketed lamp bulb envelope includes a ceramic cup having an open end and a closed end, a ceramic washer covering the open end of the ceramic cup, the washer defining an aperture therethrough, a lamp bulb positioned inside the ceramic cup abutting the aperture, and a reflective ceramic material filling an interior volume of the ceramic cup not occupied by the bulb. A method of packing a jacketed lamp bulb envelope of the type comprising a ceramic cup with a lamp bulb disposed therein includes the steps of filling the ceramic cup with a flowable slurry of reflective material, and applying centrifugal force to the cup to pack the reflective material therein.

Washing machine related injuries in children: a continuing threat

PubMed Central

Warner, B; Kenney, B; Rice, M

2003-01-01

Objective: To describe washing machine related injuries in children in the United States. Methods: Injury data for 496 washing machine related injuries documented by the Consumer Product Safety Commission's National Electronic Injury Surveillance System and death certificate data files were analyzed. Gender, age, diagnosis, body part injured, disposition, location and mechanism of injury were considered in the analysis of data. Results: The upper extremities were most frequently injured in washing machine related injuries, especially with wringer machines. Fewer than 10% of patients required admission, but automatic washers accounted for most of these and for both of the deaths. Automatic washer injuries involved a wider range of injury mechanism, including 23 children who fell from the machines while in baby seats. Conclusions: Though most injuries associated with washing machines are minor, some are severe and devastating. Many of the injuries could be avoided with improvements in machine design while others suggest a need for increased education of potential dangers and better supervision of children if they are allowed access to areas where washing machines are operating. Furthermore, washing machines should only be used for their intended purpose. Given the limitations of educational efforts to prevent injuries, health professionals should have a major role in public education regarding these seemingly benign household appliances. PMID:14693900

Testing linen disinfection procedures in practice with phage-charged-bioindicators.

PubMed

Gerhardts, Anja; Mucha, Helmut; Höfer, Dirk

2012-01-01

Disinfecting laundry processes are essential to avoid contamination of laundering machines and linen during commercial laundry reprocessing in the health care sector. Recently a bacteriophage-charged bioindicator has been developed using MS2 as surrogate virus for testing of low-temperature disinfecting laundry processing on efficacy against viruses related to practice. This paper therefore aims to investigate application of MS2-bioindicators in chemothermal processes under practical conditions (phase 2/step 2) and in practice (phase 3). The experimental design was developed and modified according to the German Society for Hygiene and Microbiology (DGHM) Standard Methods for Testing Chemical Disinfection Processes. Tests under practical conditions were performed at 60 degrees C and 70 degrees C. Additional tests in tunnel washers were carried out at 60 degrees C and 70 degrees C. In all experiments validated disinfecting laundry processes, recommended for bactericidal and virucidal performance (categories A and B), were applied. The results show a temperature-dependent gradual efficacy against the test virus MS2 up to reduction values of more than 8 log10-steps. Therefore MS2-bioindicators prove to be suitable as a tool to determine the performance of disinfection procedures against viruses in practice. Phage-charged bioindicators may be a tool to provide further insights into the reliability of antiviral laundry processes for health care quality management and for infection control.

Advanced Concepts for Composite Structure Joints and Attachment Fittings. Volume I. Design and Evaluation.

DTIC Science & Technology

1981-11-01

interlaminar tension). The analysis is also influenced by other factors such as bolt location, washer/bolt size, fastener pattern, laminate thickness, corner...to reduce the cost of tooling were also studied. These include: * Pultrusion dies for under $5, 000 * Stable, accurate, low-cost chopped-fiber phenolic ...fittings were state-of- the-art methods developed for laminated composite plates, shells, beams, and columns as used in analyses of discontinuities, edge

Timing and Spectroscopy Requirements for a Plastic Scintillating Fiber Bundle Time-of-Flight Neutron Spectrometer

DTIC Science & Technology

2013-12-01

tight aluminum box internal view. Each SiPMT is held securely in each aluminum jig with nylon washers and screws. The threaded rod extends length-wise...hole in the aluminum jig located between the threaded rod and nylon screw is the hole where the single BCF-12 scintillating fiber would be placed to...additional pixel firing from the SiPMT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 42 A typical Hamamatsu

Apollo couch energy absorbers

NASA Technical Reports Server (NTRS)

Wesselski, C. J.; Drexel, R. E.

1972-01-01

Load attenuators for the Apollo spacecraft crew couch and its potential applications are described. Energy absorption is achieved through friction and cyclic deformation of material. In one concept, energy absorption is accomplished by rolling a compressed ring of metal between two surfaces. In another concept, energy is absorbed by forcing a plastically deformed washer along a rod. Among the design problems that had to be solved were material selection, fatigue life, ring slippage, lubrication, and friction loading.

Study of Increasing Lead Times in Major Weapon Systems Acquisition.

DTIC Science & Technology

1982-07-31

Conduit Covers X X X Connectors, Electrical X X X X X Control Systems (Auto- mated, Boiler) X Davit, Boat, Power- Opera.ted X Diodes X X X X A iX...tubes. Other end uses include washers in computer equipment, electrical insulators in motors and generators, and retardation plates in lasers . Supply...relays, electron tubes, printed circuits, and resistors. Platinum is also used in dentistry and for jewelry. Supply, A small amount of platinum (less

6. VIEW LOOKING SOUTHEAST AT VENTILATION EQUIPMENT IN SOUTH VENTILATION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW LOOKING SOUTHEAST AT VENTILATION EQUIPMENT IN SOUTH VENTILATION HOUSE. THIS AIR CONDITIONING SYSTEM WAS INSTALLED BY PARKS-CRAMER COMPANY OF FITCHBURG, MASSACHUSETTS WHEN THE MILL WAS CONSTRUCTED IN 1923-24. ONE AIR WASHER AND FAN ROOM EXTERIOR IS VISIBLE ON THE RIGHT. THE DUCTS FROM BOTH FAN ROOMS (CURVED METAL STRUCTURES AT CENTER AND LEFT OF PHOTO) ARE CONNECTED TO A COMMON AIR SHAFT. - Stark Mill, 117 Corinth Road, Hogansville, Troup County, GA

The Environmental Assessment and Management (TEAM) Guide: Delaware Supplement

DTIC Science & Technology

2010-01-01

December 2008]. • Coating or Printing - coating is the application of a uniform layer of material across the entire width of a web . Printing is...excess solvent by spinning, and drying by tumbling in any air stream. The facility includes, but is not limited to, any washer, dryer , or filter...mergency f ire , r escue o r co mmunications cal ls a nd operated either by the Delaware Emergency Management Agency or by any public agency or

Analysis of Marketing and Customer Satisfaction in Base Housing Communities of the Monterey Bay Area

DTIC Science & Technology

2011-06-01

the U.S. Government. IRB Protocol number NPS.2010.0003- IR -EP7-A. 12a. DISTRIBUTION / AVAILABILITY STATEMENT Approved for public release...Reese, thank you for answering all my late-night phone calls and reminding me I should be working on my paper instead of venting. This report is...amenities include: ceiling fans, central heating, private balcony, hardwood floors, master bedroom suite, washer/ dryer hookups, media boxes for

Design and Building of an Inexpensive and Sturdy Pipet Bulb Filler Port

ERIC Educational Resources Information Center

Danielson, Neil D.; Danielson, Alex P.

2015-01-01

A pipet filler port has been constructed from a 1/4 in. NPT-1/4 in. or -3/8 in. barbed end Kynar plastic male connector fitting and a washer (cut from a latex rubber hose) inserted into the NPT end. The barbed end can secure reliably different sized rubber bulbs such as 1 oz (30 mL pipet capacity) and 2 oz (60 mL pipet capacity) types, and the 1/4…

Evaluation of ozone emissions and exposures from consumer products and home appliances.

PubMed

Zhang, Q; Jenkins, P L

2017-03-01

Ground-level ozone can cause serious adverse health effects and environmental impacts. This study measured ozone emissions and impacts on indoor ozone levels and associated exposures from 17 consumer products and home appliances that could emit ozone either intentionally or as a by-product of their functions. Nine products were found to emit measurable ozone, one up to 6230 ppb at a distance of 5 cm (2 inches). One use of these products increased room ozone concentrations by levels up to 106 ppb (mean, from an ozone laundry system) and personal exposure concentrations of the user by 12-424 ppb (mean). Multiple cycles of use of one fruit and vegetable washer increased personal exposure concentrations by an average of 2550 ppb, over 28 times higher than the level of the 1-h California Ambient Air Quality Standard for ozone (0.09 ppm). Ozone emission rates ranged from 1.6 mg/h for a refrigerator air purifier to 15.4 mg/h for a fruit and vegetable washer. The use of some products was estimated to contribute up to 87% of total daily exposures to ozone. The results show that the use of some products may result in potential health impacts. © 2016 The Authors. Indoor Air published by John Wiley & Sons Ltd.

Neural response in obsessive-compulsive washers depends on individual fit of triggers

PubMed Central

Baioui, Ali; Pilgramm, Juliane; Merz, Christian J.; Walter, Bertram; Vaitl, Dieter; Stark, Rudolf

2013-01-01

Background: Patients with obsessive-compulsive disorder (OCD) have highly idiosyncratic triggers. To fully understand which role this idiosyncrasy plays in the neurobiological mechanisms behind OCD, it is necessary to elucidate the impact of individualization regarding the applied investigation methods. This functional magnetic resonance imaging (fMRI) study explores the neural correlates of contamination/washing-related OCD with a highly individualized symptom provocation paradigm. Additionally, it is the first study to directly compare individualized and standardized symptom provocation. Methods: Nineteen patients with washing compulsions created individual OCD hierarchies, which later served as instructions to photograph their own individualized stimulus sets. The patients and 19 case-by-case matched healthy controls participated in a symptom provocation fMRI experiment with individualized and standardized stimulus sets created for each patient. Results: OCD patients compared to healthy controls displayed stronger activation in the basal ganglia (nucleus accumbens, nucleus caudatus, pallidum) for individualized symptom provocation. Using standardized symptom provocation, this group comparison led to stronger activation in the nucleus caudatus. The direct comparison of between-group effects for both symptom provocation approaches revealed stronger activation of the orbitofronto-striatal network for individualized symptom provocation. Conclusions: The present study provides insight into the differential impact of individualized and standardized symptom provocation on the orbitofronto-striatal network of OCD washers. Behavioral and neural responses imply a higher symptom-specificity of individualized symptom provocation. PMID:23630478

Surrogate alcohol containing methanol, social deprivation and public health in Novosibirsk, Russia.

PubMed

Neufeld, Maria; Lachenmeier, Dirk; Hausler, Thomas; Rehm, Jürgen

2016-11-01

Surrogate alcohol, i.e. alcohol not intended or not officially intended for human consumption, continues to play an important role in alcohol consumption in Russia, especially for people with alcohol dependence. Among the different types of surrogate alcohol, there are windshield washer antifreeze liquids; these products are the cheapest kinds of non-beverage alcohol available and thus likely to be used by the most deprived and marginalised groups such as homeless people with alcohol dependence. Although it is well known, that non-beverage alcohol is used for consumption by various groups in Russia, and although there are laws to prohibit the use of methanol as part of windshield washer antifreeze liquids for the very reason that such products could be used as surrogate alcohol, we detected products in retail sale which were a mix of water and methanol only. Methanol poses serious health threats including blindness and death, and there had been repeated methanol deaths from surrogate alcohol in Russia over the last years. If law-enforcement does not change for surrogate products, we can expect more methanol-resulting deaths in the most deprived and marginalized groups of people with alcohol dependence in Russia. In addition, ingredients with questionable safety profiles such as formic acid should also be prohibited in non-beverage alcohol products that are likely to be consumed as surrogate alcohol. Copyright © 2016. Published by Elsevier B.V.

Feasibility of Biological Effective Monitoring of Chrome Electroplaters to Chromium through Analysis of Serum Malondialdehyde.

PubMed

Mozafari, P; Rezazadeh Azari, M; Shokoohi, Y; Sayadi, M

2016-10-01

Great concern about occupational exposure to chromium (Cr [VI]) has been reported due to escalated risk of lung cancer in exposed workers. Consequences of occupational exposure to Cr (VI) have been reported as oxidative stress and lung tissue damage. To investigate the feasibility of biological effect monitoring of chrome electroplaters through analysis of serum malondialdehyde (MDA). 90 workers directly involved in chrome electroplating---categorized into three equal groups based on their job as near bath workers, degreaser, and washers---and 30 workers without exposure to Cr (VI), served as the control group, were studied. Personal samples were collected and analyzed according to NIOSH method 7600. Serum MDA level was measured by HPLC using a UV detector. Median Cr (VI) exposure level was 0.38 mg/m(3) in near bath workers, 0.20 mg/m(3) in degreasers, and 0.05 mg/m(3) in washers. The median serum MDA level of three exposed groups (2.76 μmol/L) was significantly (p<0.001) higher than that in the control group (2.00 μmol/L). There was a positive correlation between electroplaters' level of exposure to Cr (VI) and their serum MDA level (Spearman's ρ 0.806, p<0.001). Serum MDA level is a good biomarker for the level of occupational exposure to Cr (VI) in electroplaters.

Histological evaluation of the influence of magnetic field application in autogenous bone grafts in rats.

PubMed

Puricelli, Edela; Dutra, Nardier B; Ponzoni, Deise

2009-01-11

Bone grafts are widely used in oral and maxillofacial reconstruction. The influence of electromagnetic fields and magnets on the endogenous stimulation of target tissues has been investigated. This work aimed to assess the quality of bone healing in surgical cavities filled with autogenous bone grafts, under the influence of a permanent magnetic field produced by in vivo buried devices. Metal devices consisting of commercially pure martensitic stainless steel washers and titanium screws were employed. Thirty male Wistar rats were divided into 3 experimental and 3 control groups. A surgical bone cavity was produced on the right femur, and a bone graft was collected and placed in each hole. Two metallic washers, magnetized in the experimental group but not in the control group, were attached on the borders of the cavity. The animals were sacrificed on postoperative days 15, 45 and 60. The histological analysis of control and experimental samples showed adequate integration of the bone grafts, with intense bone neoformation. On days 45 and 60, a continued influence of the magnetic field on the surgical cavity and on the bone graft was observed in samples from the experimental group. The results showed intense bone neoformation in the experimental group as compared to control animals. The intense extra-cortical bone neoformation observed suggests that the osteoconductor condition of the graft may be more susceptible to stimulation, when submitted to a magnetic field.

Optimization of Fish Protection System to Increase Technosphere Safety

NASA Astrophysics Data System (ADS)

Khetsuriani, E. D.; Fesenko, L. N.; Larin, D. S.

2017-11-01

The article is concerned with field study data. Drawing upon prior information and considering structural features of fish protection devices, we decided to conduct experimental research while changing three parameters: process pressure PCT, stream velocity Vp and washer nozzle inclination angle αc. The variability intervals of examined factors are shown in the Table 1. The conicity angle was assumed as a constant one. The box design B3 was chosen as a baseline being close to D-optimal designs in its statistical characteristics. The number of device rotations and its fish fry protection efficiency were accepted as the output functions of optimization. The numerical values of regression coefficients of quadratic equations describing the behavior of optimization functions Y1 and Y2 and their formulaic errors were calculated upon the test results in accordance with the planning matrix. The adequacy or inadequacy of the obtained quadratic regression model is judged via checking the condition whether Fexp ≤ Ftheor.

Ares I-X Upper Stage Simulator Structural Analyses Supporting the NESC Critical Initial Flaw Size Assessment

NASA Technical Reports Server (NTRS)

Knight, Norman F., Jr.; Phillips, Dawn R.; Raju, Ivatury S.

2008-01-01

The structural analyses described in the present report were performed in support of the NASA Engineering and Safety Center (NESC) Critical Initial Flaw Size (CIFS) assessment for the ARES I-X Upper Stage Simulator (USS) common shell segment. The structural analysis effort for the NESC assessment had three thrusts: shell buckling analyses, detailed stress analyses of the single-bolt joint test; and stress analyses of two-segment 10 degree-wedge models for the peak axial tensile running load. Elasto-plastic, large-deformation simulations were performed. Stress analysis results indicated that the stress levels were well below the material yield stress for the bounding axial tensile design load. This report also summarizes the analyses and results from parametric studies on modeling the shell-to-gusset weld, flange-surface mismatch, bolt preload, and washer-bearing-surface modeling. These analyses models were used to generate the stress levels specified for the fatigue crack growth assessment using the design load with a factor of safety.

Microfluidic routing of aqueous and organic flows at high pressures: fabrication and characterization of integrated polymer microvalve elements.

PubMed

Kirby, Brian J; Reichmuth, David S; Renzi, Ronald F; Shepodd, Timothy J; Wiedenman, Boyd J

2005-02-01

This paper presents the first systematic engineering study of the impact of chemical formulation and surface functionalization on the performace of free-standing microfluidic polymer elements used for high-pressure fluid control in glass microsystems. System design, chemical wet-etch processes, and laser-induced polymerization techniques are described, and parametric studies illustrate the effects of polymer formulation, glass surface modification, and geometric constraints on system performance parameters. In particular, this study shows that highly crosslinked and fluorinated polymers can overcome deficiencies in previously-reported microvalve architectures, particularly limited solvent compatibility. Substrate surface modification is shown effective in reducing the friction of the polymer-glass interface and thereby facilitating valve actuation. A microchip one-way valve constructed using this architecture shows a 2 x 10(8) ratio of forward and backward flow rates at 7 MPa. This valve architecture is integrated on chip with minimal dead volumes (70 pl), and should be applicable to systems (including chromatography and chemical synthesis devices) requiring high pressures and solvents of varying polarity.

Electrochemical control of iodine disinfectant for space transportation system and space station potable water

NASA Technical Reports Server (NTRS)

Geer, Richard D.

1989-01-01

An electrochemical microbial check valve method (EC-MCV) for controlling the iodine disinfectant in potable water (PW) for NASA's space operations was proposed. The factors affecting the design and performance of the unit were analyzed. This showed that it would be feasible to construct a recyclable unit in a small volume that will operate in either an iodine removal or addition mode. The EC-MCV should remove active iodine species rapidly from PW, but the rapid delivery rates at end-use may make complete removal of excess I(-) difficult under some conditions. Its performace change with AgI buildup needs to be investigated, as this controls the time for recycling the unit. The EC-MCV has advantages over the passive microbial check valve (MCV) method currently in use, as it would allow precise control of the I2 level and would not introduce excess I(-) to the water. The presence of oxygen in the EC-MCV needs to be investigated as it could affect the efficiency of I2 addition and excess I(-) removal.

Evaluation and Repair of Concrete Structures: Annotated Bibliography 1978 - 1988. Volume 1. (Repair, Evaluation, Maintenance and Rehabilitation Research Program)

DTIC Science & Technology

1991-06-01

32303, "Application of New Technology to Maintenance and Minor Repair," for which Mr. James E. McDonald (CEWES-SC-R) was Principal Investigator. Dr. Tony...materials, shotcrete, and silica-fume concrete. 6. Section -D contains 710 references-on maintenance and repair tech- niques including bonding new concrote to...sys- -tem. The process problems have been resolved-by introduction of new instrumentation, static mixers, elimination of washers and high density

Fastener Design Manual

NASA Technical Reports Server (NTRS)

Barrett, Richard T.

1990-01-01

This manual was written for design engineers to enable them to choose appropriate fasteners for their designs. Subject matter includes fastener material selection, platings, lubricants, corrosion, locking methods, washers, inserts, thread types and classes, fatigue loading, and fastener torque. A section on design criteria covers the derivation of torque formulas, loads on a fastener group, combining simultaneous shear and tension loads, pullout load for tapped holes, grip length, head styles, and fastener strengths. The second half of this manual presents general guidelines and selection criteria for rivets and lockbolts.

Use of Excel ion exchange equilibrium solver with WinGEMS to model and predict NPE distribution in the Mead/Westvaco Evandale, TX, hardwood bleach plant

Treesearch

Christopher Litvay; Alan Rudie; Peter Hart

2003-01-01

An Excel spreadsheet developed to solve the ion-exchange equilibrium in wood pulps has been linked by dynamic data exchange to WinGEMS and used to model the non-process elements in the hardwood bleach plant of the Mead/Westvaco Evandale mill. Pulp and filtrate samples were collected from the diffusion washers and final wash press of the bleach plant. A WinGEMS model of...

German Explosive Ordnance (Projectiles and Projectile Fuzes)

DTIC Science & Technology

1953-03-01

CAP IGNITER BRIDGE INSULATION BLACK POWDER Figure 320—Electric Primers c/12nA and c/22 354 PROJECTILES 0.75 inch, length of body. 0.281 inch...of lip. 0.75 inch, length of body. Number of threads, 5 RH. CONSTRUCTION. The primer houses an igniter bridge which consists of lead styphnate...dipped in gelatin. This bridge has a resistance of approxi- mately 2.2 ohms and is in the circuit with the in- sulated contact plug, the spring washer

Laundering in space - A summary of recent developments.

NASA Technical Reports Server (NTRS)

Houck, O. K.; Symons, J. J.

1973-01-01

Clothing must be washed and reused on future long duration space missions to maintain personal hygiene without severe weight penalties of stored clothing. Laundering equipment that may operate in the absence of gravity is being developed. Weight savings expected from this equipment are illustrated in this paper that describes a six-man combined clothes washer/dryer engineering prototype. Also included in the paper is the rationale used in selecting the final prototype design as well as a discussion of major factors affecting design and performance.

Histological evaluation of the influence of magnetic field application in autogenous bone grafts in rats

PubMed Central

Puricelli, Edela; Dutra, Nardier B; Ponzoni, Deise

2009-01-01

Background Bone grafts are widely used in oral and maxillofacial reconstruction. The influence of electromagnetic fields and magnets on the endogenous stimulation of target tissues has been investigated. This work aimed to assess the quality of bone healing in surgical cavities filled with autogenous bone grafts, under the influence of a permanent magnetic field produced by in vivo buried devices. Methods Metal devices consisting of commercially pure martensitic stainless steel washers and titanium screws were employed. Thirty male Wistar rats were divided into 3 experimental and 3 control groups. A surgical bone cavity was produced on the right femur, and a bone graft was collected and placed in each hole. Two metallic washers, magnetized in the experimental group but not in the control group, were attached on the borders of the cavity. Results The animals were sacrificed on postoperative days 15, 45 and 60. The histological analysis of control and experimental samples showed adequate integration of the bone grafts, with intense bone neoformation. On days 45 and 60, a continued influence of the magnetic field on the surgical cavity and on the bone graft was observed in samples from the experimental group. Conclusion The results showed intense bone neoformation in the experimental group as compared to control animals. The intense extra-cortical bone neoformation observed suggests that the osteoconductor condition of the graft may be more susceptible to stimulation, when submitted to a magnetic field. PMID:19134221

Structural aspects of cold-formed steel section designed as U-shape composite beam

NASA Astrophysics Data System (ADS)

Saggaff, Anis; Tahir, Mahmood Md.; Azimi, Mohammadamin; Alhajri, T. M.

2017-11-01

Composite beam construction usually associated with old-style Hot-Rolled Steel Section (HRSS) has proven to act much better in compare with Cold-Formed Steel Section (CFSS) sections due to thicker section. Due, it's getting popular to replace HRSS with CFSS in some aspects as a composite beam. The advantages such as lightweight, cost effective and easy to install have contributed to the apply CFSS as a preferred construction material for composite beam. There is a few technical data available regarding the application of the usage of CFSS as a composite system, despite the potentials use for residential and light-weight industrial constructions. This paper presents an experimental tests results which have been conducted using CFSS as composite beam. Composite action of CFSS arranged as double beam with Self-Compacting Concrete (SCC) slab are integrated together with bolted shear connectors were used. A full-scale test comprised of 3 proposed composite beam specimens with bolted shear connector spaced at 300 mm interval of grade 8.8 was using single nut with washer on flange of CFS, cast to the slab and loaded until failed. The test show that the bolted shear connector yielded better capacity of ultimate strength and ultimate moment for the proposed composite beam. It can be concluded that, bolted shear connectors of 16 mm in diameter performed better than the other diameter size of bolted shear connectors.

Brain perfusion correlates of visuoperceptual deficits in Mild Cognitive Impairment and mild Alzheimer’s disease

PubMed Central

Alegret, Montserrat; Vinyes-Junqué, Georgina; Boada, Mercè; Martínez-Lage, Pablo; Cuberas, Gemma; Espinosa, Ana; Roca, Isabel; Hernández, Isabel; Valero, Sergi; Rosende-Roca, Maitée; Mauleón, Ana; Becker, James T.; Tárraga, Lluís

2012-01-01

Background Visuoperceptual processing is impaired early in the clinical course of Alzheimer’s disease (AD). The 15-Objects Test (15-OT) detects such subtle performance deficits in Mild Cognitive Impairment (MCI) and mild AD. Reduced brain perfusion in the temporal, parietal and prefrontal regions have been found in early AD and MCI patients. Objectives To confirm the role of the 15-OT in the diagnosis of MCI and AD, and to investigate the brain perfusion correlates of visuoperceptual dysfunction (15-OT) in subjects with MCI, AD and normal aging. Methods Forty-two AD, 42 MCI and 42 healthy elderly control (EC) subjects underwent a brain Single Photon Emission Tomography (SPECT) and separately completed the 15-OT. An analysis of variance compared 15-OT scores between groups. SPM5 was used to analyse the SPECT data. Results 15-OT performace was impaired in the MCI and AD patients. In terms of the SPECT scans, AD patients showed reduced perfusion in temporal-parietal regions, while the MCI subjects had decreased perfusion in the middle and posterior cingulate. When MCI and AD groups were compared, a significant brain perfusion reduction was found in temporo-parietal regions. In the whole sample, 15-OT performance was significantly correlated with the clinical dementia rating scores, and with the perfusion in the bilateral posterior cingulate and the right temporal pole, with no significant correlation in each separate group. Conclusion Our findings suggest that the 15-OT performance provides a useful gradation of impairment from normal aging to AD, and it seems to be related to perfusion in the bilateral posterior cingulate and the right temporal pole. PMID:20555146

New developments in water efficiency

NASA Astrophysics Data System (ADS)

Gregg, Tony T.; Dewees, Amanda; Gross, Drema; Hoffman, Bill; Strub, Dan; Watson, Matt

2006-10-01

An overview of significant new developments in water efficiency is presented in this paper. The areas covered will be legislative, regulatory, new programs or program wrinkles, new products, and new studies on the effectiveness of conservation programs. Examples include state and local level efficiency regulations in Texas; the final results of the national submetering study for apartments in the US; the US effort to adopt the IWA protocols for leak detection; new water efficient commercial products such as ET irrigation controllers, new models of efficient clothes washers, and innovative toilet designs.

Damping and support in high-temperature superconducting levitation systems

DOEpatents

Hull, John R [Sammamish, WA; McIver, Carl R [Everett, WA; Mittleider, John A [Kent, WA

2009-12-15

Methods and apparatuses to provide improved auxiliary damping for superconducting bearings in superconducting levitation systems are disclosed. In a superconducting bearing, a cryostat housing the superconductors is connected to a ground state with a combination of a damping strip of material, a set of linkage arms to provide vertical support, and spring washers to provide stiffness. Alternately, the superconducting bearing may be supported by a cryostat connected to a ground state by posts constructed from a mesh of fibers, with the damping and stiffness controlled by the fiber composition, size, and mesh geometry.

Parasitic modes removal out of operating mode neighbourhood in the DAW accelerating structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andreev, V.G.; Belugin, V.M.; Esin, S.K.

1983-08-01

The disk and washer (DAW) accelerating structure finds its use in a number of new projects (PIGMI, SNQ etc ). It composes the main part of the accelerating structure of the meson factory now under construction in the Institute for Nuclear Research (INR), Moscow. It is known that the parasitic modes with azimuthal field variations exist at the operating mode region. In this report different methods of the parasitic modes frequency shift are considered. The main attention is given to the resonant methods, which are the most efficient.

Preliminary Test Results of a Non-Contacting Finger Seal on a Herringbone-Grooved Rotor

NASA Technical Reports Server (NTRS)

Proctor, Margaret P.; Delgado, Irebert R.

2009-01-01

The baseline non-contacting finger seal is a NASA patented design. The primary difference between it and Gul Aroras design patented by AlliedSignal is that there are no lift pads on the high pressure fingers. The baseline non-contacting finger seal is comprised of a back plate, aft spacer, aft (or low pressure) finger element, forward (or high pressure) finger element, forward spacer, and front plate. The components are held together with 20 flat head screws. A typical seal would have a back plate of approximately the same thickness as the front plate and would be riveted together. The thicker back plate allows use of threaded fasteners so that different finger elements can be tested without having to replace all the individual seal components. The finger elements are essentially washers made of thin sheet stock with multiple curved slots machined around the inner diameter to form the fingers. They are clocked so that the fingers of one cover the slots of the other. The aft finger element fingers have axial extensions or "lift pads" at the seal id that are concentric to the rotor. The fingers act as cantilever beams and flex in response to rotor dynamic motion and radial growth of the rotor due to centrifugal or thermal forces.

Design and simulation of nanoscale double-gate TFET/tunnel CNTFET

NASA Astrophysics Data System (ADS)

Bala, Shashi; Khosla, Mamta

2018-04-01

A double-gate tunnel field-effect transistor (DG tunnel FET) has been designed and investigated for various channel materials such as silicon (Si), gallium arsenide (GaAs), alminium gallium arsenide (Al x Ga1‑x As) and CNT using a nano ViDES Device and TCAD SILVACO ATLAS simulator. The proposed devices are compared on the basis of inverse subthreshold slope (SS), I ON/I OFF current ratio and leakage current. Using Si as the channel material limits the property to reduce leakage current with scaling of channel, whereas the Al x Ga1‑x As based DG tunnel FET provides a better I ON/I OFF current ratio (2.51 × 106) as compared to other devices keeping the leakage current within permissible limits. The performed silmulation of the CNT based channel in the double-gate tunnel field-effect transistor using the nano ViDES shows better performace for a sub-threshold slope of 29.4 mV/dec as the channel is scaled down. The proposed work shows the potential of the CNT channel based DG tunnel FET as a futuristic device for better switching and high retention time, which makes it suitable for memory based circuits.

A mini review on immune role of chemokines and its receptors in snakehead murrel Channa striatus.

PubMed

Bhatt, Prasanth; Kumaresan, Venkatesh; Palanisamy, Rajesh; Ravichandran, Gayathri; Mala, Kanchana; Amin, S M Nurul; Arshad, Aziz; Yusoff, Fatimah Md; Arockiaraj, Jesu

2018-01-01

Chemokines are ubiquitous cytokine molecules involved in migration of cells during inflammation and normal physiological processes. Though the study on chemokines in mammalian species like humans have been extensively studied, characterization of chemokines in teleost fishes is still in the early stage. The present review provides an overview of chemokines and its receptors in a teleost fish, Channa striatus. C. striatus is an air breathing freshwater carnivore, which has enormous economic importance. This species is affected by an oomycete fungus, Aphanomyces invadans and a Gram negative bacteria Aeromonas hydrophila is known to cause secondary infection. These pathogens impose immune changes in the host organism, which in turn mounts several immune responses. Of these, the role of cytokines in the immune response is immense, due to their involvement in several activities of inflammation such as cell trafficking to the site of inflammation and antigen presentation. Given that importance, chemokines in fishes do have significant role in the immunological and other physiological functions of the organism, hence there is a need to understand the characteristics, activities and performace of these small molecules in details. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Jun, E-mail: lijun_yt@163.com; Key Laboratory of Advanced Display and System Applications, Ministry of Education, Shanghai University, Shanghai 200072; Huang, Chuan-Xin

Graphical abstract: This work reports the Ba content on thin film transistor based on a novel BaZnSnO semiconductor using solution process. - Highlights: • No reports about BaZnSnO thin film using solution process. • BaZnSnO thin film transistor (TFT) was firstly fabricated. • BaZnSnO-TFT shows a acceptable performace. • Influence of Ba content on BaZnSnO-TFT. - Abstract: A novel BaZnSnO semiconductor is fabricated using solution process and the influence of Ba addition on the structure, the chemical state of oxygen and electrical performance of BaZnSnO thin films are investigated. A high performance BaZnSnO-based thin film transistor with 15 mol% Bamore » is obtained, showing a saturation mobility of 1.94 cm{sup 2}/V s, a threshold voltage of 3.6 V, an on/off current ratio of 6.2 × 10{sup 6}, a subthreshold swing of 0.94 V/decade, and a good bias stability. Transistors with solution processed BaZnSnO films are promising candidates for the development of future large-area, low-cost and high-performance electronic devices.« less

A biomechanical evaluation of a cannulated compressive screw for use in fractures of the scaphoid.

PubMed

Rankin, G; Kuschner, S H; Orlando, C; McKellop, H; Brien, W W; Sherman, R

1991-11-01

The compressive force generated by a 3.5 mm ASIF cannulated cancellous screw with a 5 mm head was compared with that generated by a standard 3.5 mm ASIF screw (6 mm head), a 2.7 mm ASIF screw (5 mm head), and a Herbert screw. The screws were evaluated in the laboratory with the use of a custom-designed load washer (transducer) to the maximum compressive force generated by each screw until failure, either by thread stripping or by head migration into the specimen. Testing was done on paired cadaver scaphoids. To minimize the variability that occurs with human bone, and because of the cost and difficulty of obtaining human tissue specimens, a study was also done on polyurethane foam simulated bones. The 3.5 cannulated screw generated greater compressive forces than the Herbert screw but less compression than the 2.7 mm and 3.5 mm ASIF cortical screws. The 3.5 mm cannulated screw offers more rigid internal fixation for scaphoid fractures than the Herbert screw and gives the added advantage of placement over a guide wire.

Effectiveness of Rack Sanitation Procedures for Elimination of Bacteria from Automatic Watering Manifolds.

PubMed

Costello, Terry; Watkins, Linda; Straign, Mike; Bean, William; Toth, Linda; Rehg, Jerold

1998-03-01

An important responsibility of animal care programs is to protect research animals from exposure to potentially pathogenic microorganisms. To validate the need for steam sterilization of rodent automatic watering racks, we evaluate the post-sanitation microbial contamination of experimentally inoculated racks and of racks that had been used to house conventional mice. We tested three sanitation protocols: rack-washer sanitation without manifold flush, sanitation that included manifold flush, and sanitation that included manifold flush followed by autoclaving. Rack sanitation, with or without manifold flush, did not reliably eliminate microbial flora from the lixits or manifold drainage water. A total of 43% of all non-autoclaved racks were positive for bacterial contamination after sanitation, and racks that had been used for conventional animal housing were more frequently positive than were experimentally inoculated racks (79% vs 18%). These data indicate that steam sterilization is necessary for eliminating bacteria from automatic watering systems. These observations are particularly important in light of increasing numbers of immune-impaired rodents that may be inadvertently and unnecessarily exposed to microbial pathogens via the automatic watering system.

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

NASA Technical Reports Server (NTRS)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

An audit of Cryptosporidium and Giardia detection in Scottish National Health Service Diagnostic Microbiology Laboratories.

PubMed

Alexander, C L; Currie, S; Pollock, K; Smith-Palmer, A; Jones, B L

2017-06-01

Giardia duodenalis and Cryptosporidium species are protozoan parasites capable of causing gastrointestinal disease in humans and animals through the ingestion of infective faeces. Whereas Cryptosporidium species can be acquired locally or through foreign travel, there is the mis-conception that giardiasis is considered to be largely travel-associated, which results in differences in laboratory testing algorithms. In order to determine the level of variation in testing criteria and detection methods between diagnostic laboratories for both pathogens across Scotland, an audit was performed. Twenty Scottish diagnostic microbiology laboratories were invited to participate with questions on sample acceptance criteria, testing methods, testing rates and future plans for pathogen detection. Reponses were received from 19 of the 20 laboratories representing each of the 14 territorial Health Boards. Detection methods varied between laboratories with the majority performing microscopy, one using a lateral flow immunochromatographic antigen assay, another using a manually washed plate-based enzyme immunoassay (EIA) and one laboratory trialling a plate-based EIA automated with an EIA plate washer. Whereas all laboratories except one screened every stool for Cryptosporidium species, an important finding was that significant variation in the testing algorithm for detecting Giardia was noted with only four laboratories testing all diagnostic stools. The most common criteria were 'travel history' (11 laboratories) and/or 'when requested' (14 laboratories). Despite only a small proportion of stools being examined in 15 laboratories for Giardia (2%-18% of the total number of stools submitted), of interest is the finding that a higher positivity rate was observed for Giardia than Cryptosporidium in 10 of these 15 laboratories. These findings highlight that the underreporting of Giardia in Scotland is likely based on current selection and testing algorithms.

Mount Protects Thin-Walled Glass or Ceramic Tubes from Large Thermal and Vibration Loads

NASA Technical Reports Server (NTRS)

Amato, Michael; Schmidt, Stephen; Marsh. James; Dahya, Kevin

2011-01-01

The design allows for the low-stress mounting of fragile objects, like thin walled glass, by using particular ways of compensating, isolating, or releasing the coefficient of thermal expansion (CTE) differences between the mounted object and the mount itself. This mount profile is lower than true full kinematic mounting. Also, this approach enables accurate positioning of the component for electrical and optical interfaces. It avoids the higher and unpredictable stress issues that often result from potting the object. The mount has been built and tested to space-flight specifications, and has been used for fiber-optic, optical, and electrical interfaces for a spaceflight mission. This mount design is often metal and is slightly larger than the object to be mounted. The objects are optical or optical/electrical, and optical and/or electrical interfaces are required from the top and bottom. This requires the mount to be open at both ends, and for the object s position to be controlled. Thin inside inserts at the top and bottom contact the housing at defined lips, or edges, and hold the fragile object in the mount. The inserts can be customized to mimic the outer surface of the object, which further reduces stress. The inserts have the opposite CTE of the housing material, partially compensating for the CTE difference that causes thermal stress. A spring washer is inserted at one end to compensate for more CTE difference and to hold the object against the location edge of the mount for any optical position requirements. The spring also ensures that any fiber-optic or optic interface, which often requires some pressure to ensure a good interface, does not overstress the fragile object. The insert thickness, material, and spring washer size can be traded against each other to optimize the mount and stresses for various thermal and vibration load ranges and other mounting requirements. The alternate design uses two separate, unique features to reduce stress and hold the object. A release agent is applied to the inside surface of the mount just before the binding potting material is injected in the mount. This prevents the potting material from bonding to the mount, and thus prevents stress from being applied, at very low temperatures, to the fragile object being mounted. The potting material mixing and curing is temperature- and humidity-controlled. The mount has radial grooves cut in it that the potting material fills, thus controlling the vertical position of the mounted object. The design can easily be used for long and thin objects, short and wide objects, and any shape in between. The design s advantages are amplified for long and thin fragile objects. The general testing range was 45 to +45 C, but multiple mounts were successfully tested down to 60 and up to 50 C and the design can be adjusted for larger ranges.

[Development and validation of an analytical method to quantify residues of cleaning products able to inactivate prion].

PubMed

Briot, T; Robelet, A; Morin, N; Riou, J; Lelièvre, B; Lebelle-Dehaut, A-V

2016-07-01

In this study, a novel analytical method to quantify prion inactivating detergent in rinsing waters coming from the washer-disinfector of a hospital sterilization unit has been developed. The final aim was to obtain an easy and functional method in a routine hospital process which does not need the cleaning product manufacturer services. An ICP-MS method based on the potassium dosage of the washer-disinfector's rinsing waters was developed. Potassium hydroxide is present on the composition of the three prion inactivating detergent currently on the French market. The detergent used in this study was the Actanios LDI(®) (Anios laboratories). A Passing and Bablok regression compares concentrations measured with this developed method and with the HPLC-UV manufacturer method. According to results obtained, the developed method is easy to use in a routine hospital process. The Passing and Bablok regression showed that there is no statistical difference between the two analytical methods during the second rinsing step. Besides, both methods were linear on the third rinsing step, with a 1.5ppm difference between the concentrations measured for each method. This study shows that the ICP-MS method developed is nonspecific for the detergent, but specific for the potassium element which is present in all prion inactivating detergent currently on the French market. This method should be functional for all the prion inactivating detergent containing potassium, if the sensibility of the method is sufficient when the potassium concentration is very low in the prion inactivating detergent formulation. Copyright © 2016. Published by Elsevier Masson SAS.

Use of a stainless steel washer platform to study Acinetobacter baumannii adhesion and biofilm formation on abiotic surfaces.

PubMed

Orsinger-Jacobsen, Samantha J; Patel, Shenan S; Vellozzi, Ernestine M; Gialanella, Phillip; Nimrichter, Leonardo; Miranda, Kildare; Martinez, Luis R

2013-12-01

Acinetobacter baumannii is a frequent cause of hospital-acquired pneumonia, and has recently increased in incidence as the causative agent of severe disease in troops wounded in Afghanistan and Iraq. Clinical approaches are limited since A. baumannii strains isolated from patients are extremely resistant to current antimicrobials. A. baumannii can survive desiccation and during outbreaks has been recovered from various sites in the patients' environment. To better understand its prevalence in hospital settings, we used a stainless steel washer (SSW) platform to investigate A. baumannii biofilm formation on abiotic surfaces. Scanning electron microscopy demonstrated that A. baumannii forms strong biofilms on stainless steel surfaces. This platform was combined with a colorimetric 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl]-2H-tetrazolium hydroxide (XTT) reduction assay to observe the metabolic activity of bacterial cells, and to facilitate the manipulation and comparison of multiple A. baumannii clinical strains. A strong correlation between XTT and c.f.u. assays was demonstrated. To complement the cell viability assays, A. baumannii biofilm mass was measured by crystal violet staining. Furthermore, the effect of commonly used disinfectants and environmental stressors on A. baumannii biofilms and planktonic cells was compared and characterized. Biofilms on SSWs were significantly more resistant than their planktonic counterparts, providing additional evidence that may allow us to understand the high prevalence of this microbe in hospital settings. Our results validate that SSWs are a simple, versatile and innovative method to study A. baumannii biofilms in vitro.

Efficacy of Neutral pH Electrolyzed Water in Reducing Escherichia coli O157:H7 and Salmonella Typhimurium DT 104 on Fresh Produce Items using an Automated Washer at Simulated Food Service Conditions.

PubMed

Afari, George K; Hung, Yen-Con; King, Christopher H

2015-08-01

The objective of this study was to determine the efficacy of neutral pH electrolyzed (NEO) water (155 mg/L free chlorine, pH 7.5) in reducing Escherichia coli O157:H7 and Salmonella Typhimurium DT 104 on romaine lettuce, iceberg lettuce, and tomatoes washed in an automated produce washer for different times and washing speeds. Tomatoes and lettuce leaves were spot inoculated with 100 μL of a 5 strain cocktail mixture of either pathogen and washed with 10 or 8 L of NEO water, respectively. Washing lettuce for 30 min at 65 rpm led to the greatest reductions, with 4.2 and 5.9 log CFU/g reductions achieved for E. coli O157:H7 and S. Typhimurium respectively on romaine, whereas iceberg lettuce reductions were 3.2 and 4.6 log CFU/g for E. coli O157:H7 and S. Typhimurium respectively. Washing tomatoes for 10 min at 65 rpm achieved reductions greater than 8 and 6 log CFU/tomato on S. Typhimurium and E. coli O157:H7 respectively. All pathogens were completely inactivated in NEO water wash solutions. No detrimental effects on the visual quality of the produce studied were observed under all treatment conditions. Results show the adoption of this washing procedure in food service operations could be useful in ensuring produce safety. © 2015 Institute of Food Technologists®

Use of a stainless steel washer platform to study Acinetobacter baumannii adhesion and biofilm formation on abiotic surfaces

PubMed Central

Orsinger-Jacobsen, Samantha J.; Patel, Shenan S.; Vellozzi, Ernestine M.; Gialanella, Phillip; Nimrichter, Leonardo; Miranda, Kildare

2013-01-01

Acinetobacter baumannii is a frequent cause of hospital-acquired pneumonia, and has recently increased in incidence as the causative agent of severe disease in troops wounded in Afghanistan and Iraq. Clinical approaches are limited since A. baumannii strains isolated from patients are extremely resistant to current antimicrobials. A. baumannii can survive desiccation and during outbreaks has been recovered from various sites in the patients’ environment. To better understand its prevalence in hospital settings, we used a stainless steel washer (SSW) platform to investigate A. baumannii biofilm formation on abiotic surfaces. Scanning electron microscopy demonstrated that A. baumannii forms strong biofilms on stainless steel surfaces. This platform was combined with a colorimetric 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl]-2H-tetrazolium hydroxide (XTT) reduction assay to observe the metabolic activity of bacterial cells, and to facilitate the manipulation and comparison of multiple A. baumannii clinical strains. A strong correlation between XTT and c.f.u. assays was demonstrated. To complement the cell viability assays, A. baumannii biofilm mass was measured by crystal violet staining. Furthermore, the effect of commonly used disinfectants and environmental stressors on A. baumannii biofilms and planktonic cells was compared and characterized. Biofilms on SSWs were significantly more resistant than their planktonic counterparts, providing additional evidence that may allow us to understand the high prevalence of this microbe in hospital settings. Our results validate that SSWs are a simple, versatile and innovative method to study A. baumannii biofilms in vitro. PMID:24025603

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, W.P.; Burkhardt, H.L.; Alsager, M.

Surveys were conducted of 200 machines owned by 194 dentists. The survey consisted of: a visual check of the condition of the machine; determination of whether adequate aluminum filtration and a lead washer were installed; and a check of the condition of the tube housing shielding with a radiation survey meter. The exposures received by the dentist and his assistant while in their normal positions were also measured. Recommended changes in operating technique were: operation at a higher voltage and lower amperage; use of high- speed film; and underexposure and overdevelopment of the film. Before washers and filters were changedmore » it was found that the equivalent filtration in 161 machines was less than 2.5 mm of aluminum, 19 machines had 2.5 mm, and 20 had an unknown amount. Before the program was initiated the beam diameter of 100 machines was 2.75 in.; 71 were larger than 2.75 in., and in 29 cases, unknown. Emulsion rating of film used initially was: 120 dentists used fast, 67 intermediate, 6 slow, and 7 films of unknown speed. The operating kilovoltage varied widely: 11 operated at 50-3 kv, 117 at 65-7, 29 at 70-2, 15 at 80-90, and 18 at an unknown voltage. It was found that 11 machines still in use were manufactured before 1935, 23 were manufactured from 1935 to 1944, 44 from 1955 to 1960, and 20 had an unknown date of manufacture. Although in most instances radiation levels did not approach the maximum allowable limits, it was recommended all unnecessary radiation exposure be eliminated. (H.H.D.)« less

Tunable microstrip SQUID amplifiers for the Gen 2 Axion Dark Matter eXperiment (ADMX)

NASA Astrophysics Data System (ADS)

O'Kelley, Sean; Hilton, Gene; Clarke, John; ADMX Collaboration

2016-03-01

We present a series of tunable microstrip SQUID (Superconducting Quantum Interference Device) amplifiers (MSAs) for installation in ADMX. The axion dark matter candidate is detected via Primakoff conversion to a microwave photon in a high-Q (~100,000) tunable microwave cavity cooled with a dilution refrigerator in a 7-tesla magnetic field. The microwave photon frequency ν is a function of the unknown axion mass, so both the cavity and amplifier must be scanned over a wide frequency range. An MSA is a linear, phase-preserving amplifier consisting of a square washer loop, fabricated from a thin Nb film, incorporating two Josephson tunnel junctions with resistive shunts to prevent hysteresis. The input is coupled via a microstrip made from a square Nb coil deposited over the washer with an intervening insulating layer. Tunability is achieved by terminating the microstrip with GaAs varactors that operate below 100 mK. By varying the varactor capacitance with a bias voltage, the resonant frequency is varied by up to a factor of 2. We demonstrate several devices operating below 100 mK, matched to the discrete operating bands of ADMX at frequencies ranging from 560 MHz to 1 GHz. The MSAs exhibit gains exceeding 20 dB and the associated noise temperatures, measured with a hot/cold load, approach the standard quantum limit (hν/kB) . Supported by DOE Grants DE - FG02 - 97ER41029, DE - FG02 - 96ER40956, DE - AC52 - 07NA27344, DE - AC03 - 76SF00098, and the Livermore LDRD program.

Antimicrobial effect of an ultrasonic levitation washer disinfector with silver electrolysis and ozone oxidation on methicillin-resistant Staphylococcus aureus.

PubMed

Tamai, Mariko; Matsushita, Shigeto; Miyanohara, Hiroaki; Imuta, Naoko; Ikeda, Ryuji; Kawai, Kazuhiro; Nishi, Junichiro; Sakamoto, Akihiro; Shigihara, Takanori; Kanekura, Takuro

2013-12-01

Methicillin-resistant Staphylococcus aureus (MRSA) has rapidly emerged as a cause of severe and intractable skin infection. At present, there are no effective topical treatments, and infection or colonization by MRSA of the skin raises serious medical problems. We developed an ultrasonic levitation washer that generates silver ions (Ag(+)) and ozone (O3) to clean and sterilize medical devices. We report the effect of ultrasonic levitation (levitation) with Ag(+) and O3 on MRSA in vitro and in vivo. Antimicrobial effect against six MRSA strains of all agr types was examined under three in vitro conditions; cells floating in a water tank, cells infiltrating-, and cells forming a biofilm on an atelocollagen membrane. In the in vivo studies, we assayed the number of MRSA organisms that survived treatment on murine skin ulcers and evaluated the ulcer size. Levitation with Ag(+) dramatically decreased the survival of MRSA floating in a water tank. Levitation with Ag(+) and O3 significantly decreased the viability of MRSA that had infiltrated or formed a biofilm on atelocollagen membranes regardless of the level of biofilm production. In vivo studies showed that the number of MRSA on murine skin ulcers was significantly decreased when 15-min treatment was performed for 7 consecutive days and that the ulcer size was significantly decreased after the seventh treatment course. Levitation with Ag(+) and O3 may be a valuable tool for treating MRSA infestation of the skin and for accelerating wound healing. © 2013 Japanese Dermatological Association.

5. VIEW OF VENTILATION HOUSES AND ROOF MONITOR FROM SOUTHEAST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. VIEW OF VENTILATION HOUSES AND ROOF MONITOR FROM SOUTHEAST CORNER OF ROOF. ROOF MONITOR WINDOWS HAVE BEEN INFILLED WITH BRICK. THE VENTILATION HOUSES ARE PART OF THE ORIGINAL CENTRAL AIR CONDITIONING SYSTEM AND CONTAINED AIR WASHERS, FANS AND OTHER HUMIDFYING EQUIPMENT FROM PARKS-CRAMER COMPANY OF FITCHBURG, MASSACHUSETTS. LOCATING THIS EQUIPMENT ON THE ROOF MADE IT UNNECESSARY TO CONSTRUCT A FULL BASEMENT, AND THEREFORE LOWERED CONSTRUCTION COSTS. THIS ARRANGEMENT ALSO PUT THE AIR CONDITIONING EQUIPMENT CLOSEST TO THE TOP FLOOR SPINNING ROOM, WHICH HAD THE GREATEST COOLING REQUIREMENTS. - Stark Mill, 117 Corinth Road, Hogansville, Troup County, GA

Cost analysis in support of minimum energy standards for clothes washers and dryers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-02-02

The results of the cost analysis of energy conservation design options for laundry products are presented. The analysis was conducted using two approaches. The first, is directed toward the development of industrial engineering cost estimates of each energy conservation option. This approach results in the estimation of manufacturers costs. The second approach is directed toward determining the market price differential of energy conservation features. The results of this approach are shown. The market cost represents the cost to the consumer. It is the final cost, and therefore includes distribution costs as well as manufacturing costs.

Core/coil assembly for use in superconducting magnets and method for assembling the same

DOEpatents

Kassner, David A.

1979-01-01

A core/coil assembly for use in a superconducting magnet of the focusing or bending type used in syncronous particle accelerators comprising a coil assembly contained within an axial bore of the stacked, washer type, carbon steel laminations which comprise the magnet core assembly, and forming an interference fit with said laminations at the operating temperature of said magnet. Also a method for making such core/coil assemblies comprising the steps of cooling the coil assembly to cryogenic temperatures and drawing it rapidly upwards into the bore of said stacked laminations.

Technical support document: Energy conservation standards for consumer products: Dishwashers, clothes washers, and clothes dryers including: Environmental impacts; regulatory impact analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-12-01

The Energy Policy and Conservation Act as amended (P.L. 94-163), establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. This Technical Support Document presents the methodology, data and results from the analysis of the energy and economic impacts of standards on dishwashers, clothes washers, and clothes dryers. The economic impact analysis is performed in five major areas: An Engineering Analysis, which establishes technical feasibility and product attributesmore » including costs of design options to improve appliance efficiency. A Consumer Analysis at two levels: national aggregate impacts, and impacts on individuals. The national aggregate impacts include forecasts of appliance sales, efficiencies, energy use, and consumer expenditures. The individual impacts are analyzed by Life-Cycle Cost (LCC), Payback Periods, and Cost of Conserved Energy (CCE), which evaluate the savings in operating expenses relative to increases in purchase price; A Manufacturer Analysis, which provides an estimate of manufacturers' response to the proposed standards. Their response is quantified by changes in several measures of financial performance for a firm. An Industry Impact Analysis shows financial and competitive impacts on the appliance industry. A Utility Analysis that measures the impacts of the altered energy-consumption patterns on electric utilities. A Environmental Effects analysis, which estimates changes in emissions of carbon dioxide, sulfur oxides, and nitrogen oxides, due to reduced energy consumption in the home and at the power plant. A Regulatory Impact Analysis collects the results of all the analyses into the net benefits and costs from a national perspective. 47 figs., 171 tabs. (JF)« less

Self-aligned top-gate amorphous indium zinc oxide thin-film transistors exceeding low-temperature poly-Si transistor performance.

PubMed

Park, Jae Chul; Lee, Ho-Nyeon; Im, Seongil

2013-08-14

Thin-film transistor (TFT) is a key component of active-matrix flat-panel displays (AMFPDs). These days, the low-temperature poly silicon (LTPS) TFTs are to match with advanced AMFPDs such as the active matrix organic light-emitting diode (AMOLED) display, because of their high mobility for fast pixel switching. However, the manufacturing process of LTPS TFT is quite complicated, costly, and scale-limited. Amorphous oxide semiconductor (AOS) TFT technology is another candidate, which is as simple as that of conventioanl amorphous (a)-Si TFTs in fabrication but provides much superior device performances to those of a-Si TFTs. Hence, various AOSs have been compared with LTPS for active channel layer of the advanced TFTs, but have always been found to be relatively inferior to LTPS. In the present work, we clear the persistent inferiority, innovating the device performaces of a-IZO TFT by adopting a self-aligned coplanar top-gate structure and modifying the surface of a-IZO material. Herein, we demonstrate a high-performance simple-processed a-IZO TFT with mobility of ∼157 cm(2) V(-1) s(-1), SS of ∼190 mV dec(-1), and good bias/photostabilities, which overall surpass the performances of high-cost LTPS TFTs.

Development of a multivariate tool to reject background in a WZ diboson search for the CDF experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cremonesi, Matteo

In the frame of the strong on-going data analysis effort of the CDF collaboration at Fermilab, a method was developed by the candidate to improve the background rejection efficiency in the search for associated pair production of electroweak W, Z bosons. The performaces of the method for vetoing the tt background in a WZ/ZZ → fνqmore » $$\\bar{q}$$ diboson search are reported. The method was developed in the inclusive 2-jets sample and applied to the “tag-2 jets" region, the subsample defined by the request that the two jets carry beauty flavor. In this region the tt production is one of the largest backgrounds. The tt veto proceeds in two steps: first, a set of pre-selection cuts are applied in a candidate sample where up to two leptons are accepted in addition to a jet pair, and the ZZ component of the signal is thus preserved; next, a Neural Network is trained to indicate the probability that the event be top-pair production. To validate the the method as developed in the inclusive 2-jets sample, it is applied to veto region providing a significant rejection of this important background.« less

Apparatus for high speed rotation of electrically operated devices

DOEpatents

Williams, Keith E.; Rogus, Arnold J.

1976-10-26

Most high speed centrifuges employ a relatively small diameter elongate flexible drive shaft, sometimes called a "quill" shaft. These relatively slender shafts are flexible to absorb vibration as the assembly passes through speeds of resonance and to permit re-alignment of the axis of rotation of the shaft and the rotor driven thereby in the event the center of mass of the rotor and shaft assembly is displaced from the nominal axis of the rotation. To use such an apparatus for testing electrical devices and components, electrical conductors for wires are passed from a slip ring assembly located at an end of the quill shaft remote from the rotor and longitudinally alongside the quill shaft to the electrical device mounted on the rotor. The longitudinally extending conductors are supported against the radially outward directed centrifugal forces by a plurality of strong, self-lubricating, slightly compressible wafers or washers co-axially stacked on the slender shaft and provided with radially offset longitudinally aligned openings to support the longitudinally extending conductors. The conductors are supported against the centrifugal forces and thus protected from rupture or other damage without restricting or constraining the essential flexure or bending of the drive shaft.

Restraint deformation and corrosion protection of gold deposited aluminum mirrors for cold optics of mid-infrared instruments

NASA Astrophysics Data System (ADS)

Uchiyama, Mizuho; Miyata, Takashi; Sako, Shigeyuki; Kamizuka, Takafumi; Nakamura, Tomohiko; Asano, Kentaro; Okada, Kazushi; Onaka, Takashi; Sakon, Itsuki; Kataza, Hirokazu; Sarugaku, Yuki; Kirino, Okiharu; Nakagawa, Hiroyuki; Okada, Norio; Mitsui, Kenji

2014-07-01

We report the restraint deformation and the corrosion protection of gold deposited aluminum mirrors for mid-infrared instruments. To evaluate the deformation of the aluminum mirrors by thermal shrinkage, monitoring measurement of the surface of a mirror has been carried out in the cooling cycles from the room temperature to 100 K. The result showed that the effect of the deformation was reduced to one fourth if the mirror was screwed with spring washers. We have explored an effective way to prevent the mirror from being galvanically corroded. A number of samples have been prepared by changing the coating conditions, such as inserting an insulation layer, making a multi-layer and overcoating water blocking layer, or carrying out precision cleaning before coating. Precision cleaning before the deposition and protecting coat with SiO over the gold layer seemed to be effective in blocking corrosion of the aluminum. The SiO over-coated mirror has survived the cooling test for the mid-infrared use and approximately 1 percent decrease in the reflectance has been detected at 6-25 microns compared to gold deposited mirror without coating.

Supersonic gas-liquid cleaning system

NASA Technical Reports Server (NTRS)

Caimi, Raoul E. B.; Thaxton, Eric A.

1994-01-01

A system to perform cleaning and cleanliness verification is being developed to replace solvent flush methods using CFC 113 for fluid system components. The system is designed for two purposes: internal and external cleaning and verification. External cleaning is performed with the nozzle mounted at the end of a wand similar to a conventional pressure washer. Internal cleaning is performed with a variety of fixtures designed for specific applications. Internal cleaning includes tubes, pipes, flex hoses, and active fluid components such as valves and regulators. The system uses gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the object to be cleaned. Compressed air or any inert gas may be used to provide the conveying medium for the liquid. The converging-diverging nozzles accelerate the gas-liquid mixture to supersonic velocities. The liquid being accelerated may be any solvent including water. This system may be used commercially to replace CFC and other solvent cleaning methods widely used to remove dust, dirt, flux, and lubricants. In addition, cleanliness verification can be performed without the solvents which are typically involved. This paper will present the technical details of the system, the results achieved during testing at KSC, and future applications for this system.

Bulb Miser

NASA Technical Reports Server (NTRS)

1978-01-01

The Bulb-Miser was developed during NASA's Apollo program to protect the Saturn launch vehicle from electrical current surge. It is now being produced for the commercial market by Bulb-Miser, Inc., Houston, Texas. Technically known as a "temperature compensating thermistor," the Bulb-Miser is a simple, inexpensive device which looks like a washer about the size of a quarter. It is slipped between bulb and socket and can be used with any incandescent bulb that screws into a standard socket. In addition to delaying burnout, the Bulb-Miser also offers some reduction of electrical energy. But the economy of the device goes beyond energy use or bulb cost; to big users of bulbs, it makes possible substantially lower maintenance labor costs. One field test involving an apartment complex showed that it took two men 30 man hours monthly to replace light bulbs; after Bulb-Miser installation only nine man hours a month were needed. Bulb-Misers are used not only in private homes but also by hospitals, schools, hotels and motels, restaurants, banks and firms providing contract maintenance for large outdoor electric signs. The broadest use is in industrial facilities; the list of big companies which have purchased the Bulb-Miser reads like a Who's Who of American industry.

Single-pulse x-ray diffraction using polycapillary optics for in situ dynamic diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maddox, B. R., E-mail: maddox3@llnl.gov; Akin, M. C., E-mail: akin1@llnl.gov; Teruya, A.

2016-08-15

Diagnostic use of single-pulse x-ray diffraction (XRD) at pulsed power facilities can be challenging due to factors such as the high flux and brightness requirements for diffraction and the geometric constraints of experimental platforms. By necessity, the x-ray source is usually positioned very close, within a few inches of the sample. On dynamic compression platforms, this puts the x-ray source in the debris field. We coupled x-ray polycapillary optics to a single-shot needle-and-washer x-ray diode source using a laser-based alignment scheme to obtain high-quality x-ray diffraction using a single 16 ns x-ray pulse with the source >1 m from themore » sample. The system was tested on a Mo sample in reflection geometry using 17 keV x-rays from a Mo anode. We also identified an anode conditioning effect that increased the x-ray intensity by 180%. Quantitative measurements of the x-ray focal spot produced by the polycapillary yielded a total x-ray flux on the sample of 3.3 ± 0.5 × 10{sup 7} molybdenum Kα photons.« less

Inactivation of Foot-and-Mouth Disease Virus by Citric Acid and Sodium Carbonate with Deicers

PubMed Central

Hong, Jang-Kwan; You, Su-Hwa; Kim, Su-Mi; Tark, Dongseob; Lee, Hyang-Sim; Ko, Young-Joon; Seo, Min-Goo; Park, Jong-Hyeon; Kim, Byounghan

2015-01-01

Three out of five outbreaks of foot-and-mouth disease (FMD) since 2010 in the Republic of Korea have occurred in the winter. At the freezing temperatures, it was impossible to spray disinfectant on the surfaces of vehicles, roads, and farm premises because the disinfectant would be frozen shortly after discharge and the surfaces of the roads or machines would become slippery in cold weather. In this study, we added chemical deicers (ethylene glycol, propylene glycol, sodium chloride, calcium chloride, ethyl alcohol, and commercial windshield washer fluid) to keep disinfectants (0.2% citric acid and 4% sodium carbonate) from freezing, and we tested their virucidal efficacies under simulated cold temperatures in a tube. The 0.2% citric acid could reduce the virus titer 4 logs at −20°C with all the deicers. On the other hand, 4% sodium carbonate showed little virucidal activity at −20°C within 30 min, although it resisted being frozen with the function of the deicers. In conclusion, for the winter season, we may recommend the use of citric acid (>0.2%) diluted in 30% ethyl alcohol or 25% sodium chloride solvent, depending on its purpose. PMID:26319879

Supersonic gas-liquid cleaning system

NASA Astrophysics Data System (ADS)

Caimi, Raoul E. B.; Thaxton, Eric A.

1994-02-01

A system to perform cleaning and cleanliness verification is being developed to replace solvent flush methods using CFC 113 for fluid system components. The system is designed for two purposes: internal and external cleaning and verification. External cleaning is performed with the nozzle mounted at the end of a wand similar to a conventional pressure washer. Internal cleaning is performed with a variety of fixtures designed for specific applications. Internal cleaning includes tubes, pipes, flex hoses, and active fluid components such as valves and regulators. The system uses gas-liquid supersonic nozzles to generate high impingement velocities at the surface of the object to be cleaned. Compressed air or any inert gas may be used to provide the conveying medium for the liquid. The converging-diverging nozzles accelerate the gas-liquid mixture to supersonic velocities. The liquid being accelerated may be any solvent including water. This system may be used commercially to replace CFC and other solvent cleaning methods widely used to remove dust, dirt, flux, and lubricants. In addition, cleanliness verification can be performed without the solvents which are typically involved. This paper will present the technical details of the system, the results achieved during testing at KSC, and future applications for this system.

Coaxial line configuration for microwave power transmission study of YBa2Cu3O(7-delta) thin films

NASA Technical Reports Server (NTRS)

Chorey, C. M.; Miranda, F. A.; Bhasin, K. B.

1991-01-01

Microwave transmission measurements through YBa2Cu3O(7-delta) (YBCO) high-transition-temperature superconducting thin films on lanthanum aluminate (LaAlO3) have been performed in a coaxial line at 10 GHz. LaAlO3 substrates were ultrasonically machined into washer-shaped discs, polished, and coated with laser-ablated YBCO. These samples were mounted in a 50-ohm coaxial air line to form a short circuit. The power transmitted through the films as a function of temperature was used to calculate the normal state conductivity and the magnetic penetration depth for the films.

Helical self-organization and hierarchical self-assembly of an oligoheterocyclic pyridine-pyridazine strand into extended supramolecular fibers.

PubMed

Cuccia, Louis A; Ruiz, Eliseo; Lehn, Jean-Marie; Homo, Jean-Claude; Schmutz, Marc

2002-08-02

The synthesis and characterization of an alternating pyridine-pyridazine strand comprising thirteen heterocycles are described. Spontaneous folding into a helical secondary structure is based on a general molecular self-organization process enforced by the conformational information encoded within the primary structure of the molecular strand itself. Conformational control based on heterocyclic "helicity codons" illustrates a strategy for designing folding properties into synthetic oligomers (foldamers). Strong intermolecular interactions of the highly ordered lock-washer subunits of compound 3 results in hierarchical supramolecular self-assembly into protofibrils and fibrils. Compound 3 also forms mechanically stable two-dimensional Langmuir-Blodgett and cast thin films.

SEALED INSULATOR BUSHING

DOEpatents

Carmichael, H.

1952-11-11

The manufacture of electrode insulators that are mechanically strong, shock-proof, vacuum tight, and are capable of withstanding gas pressures of many atmospheres under intense neutron bombardment, such as may be needed in an ionization chamber, is described. The ansulator comprises a bolt within a quartz tube, surrounded by a bushing held in place by two quartz rings, and tightened to a pressure of 1,000 pounds per square inch by a nut and washer. Quartz is the superior material to meet these conditions, however, to withstand this pressure the quartz must be fire polished, lapped to form smooth and parallel surfaces, and again fire polished to form an extremely smooth and fracture resistant mating surface.

Effects of drying agents on bond strength of etch-and-rinse adhesive systems to enamel immediately after bleaching.

PubMed

Niat, Alireza Boruzi; Yazdi, Fatmeh Maleknejad; Koohestanian, Niloufar

2012-12-01

To determine the effect of drying agents and adhesive solvents on the bond strength of resin composite to enamel immediately after bleaching. Sixty healthy human premolars were bleached using 15% carbamide peroxide gel and randomly divided into three groups according to the immersing solutions applied immediately after bleaching: 70% alcohol, acetone, and distilled water. Each group was randomly divided into two subgroups according to the adhesives that were applied: an alcohol-based adhesive (Single Bond) and an acetone-based adhesive (One Step). By using rubber washers, composite Z100 was placed onto the enamel and shear bond strength was evaluated in a universal testing machine at a crosshead speed of 1 mm/min. The type of failure was also assessed using a stereomicroscope. The data were statistically analyzed by two-way ANOVA and Tukey's post-hoc test (α = 0.05). Fisher's Exact test was used to evaluate differences in the failure modes. Statistical analysis showed that the bond strength of the distilled water groups was significantly lower than that of the other groups, but the bond strengths of the two groups where a drying agent was applied were similar to that of the unbleached group. The acetone-based adhesive (One Step) provided higher bond strength than did the alcohol-based adhesive (Single Bond) (p < 0.05). There was no interaction between the two variables (p > 0.05). Fisher's Exact test showed there was no significant difference in the failure mode of all the experimental groups (p > 0.05). The application of drying agents improves the bond strength of resin composite to bleached enamel. Furthermore, the acetone-based adhesive used in the study had a higher bond strength to bleached enamel than did the alcohol-based adhesive used.

Correlates of Achieving the Guidelines of Four Forms of Physical Activity, and the Relationship between Guidelines Achievement and Academic Performance: Undergraduate Students in Finland.

PubMed

El Ansari, Walid; Suominen, Sakari; Draper, Steve

2017-06-01

We surveyed and compared, by gender, the levels and correlates of achieving the international guidelines of four forms of physical activity (PA): moderate PA (MPA), vigorous PA (VPA), moderate or vigorous PA (MVPA), and muscle strengthening PA (MSPA). The study assessed the associations between achieving the guidelines of the four PA forms and a range of socio-demographic, health and academic performance variables. Data was collected across the seven faculties of the University of Turku (2013-2014 from a representative sample of 1,189 undergraduates). An English language online self-administered questionnaire assessed frequency and duration of PA/week for each form of PA. We employed cut-offs for the guidelines in accordance with the American Heart Association. Chi-square statistic tested the differences in PA, socio-demographic variables and academic performance between males and females. Binary logistic regression examined the factors associated with achieving the four PA guidelines and linear regression examined the association between the frequency of PA and academic performance. Achievement of PA guidelines was relatively low across the sample. Female students were less likely to achieve the VPA or MSPA guidelines, but were more health conscious and in generally exhibited better academic performace than males. High health awareness and excellent/very good self-rated health were the strongest predictors of achieving all forms of PA. Parents' education level was positively related to likelihood of achieving the VPA, MVPA and MSPA guidelines. Achieving the MPA guidelines (but not VPA or MSPA) was positively associated with subjective perceptions of better academic performance. Achievement of PA guidelines was generally low for this sample of Finnish students, and was associated with positive health status and high health awareness. Universities need a holistic approach to improve awareness of health and promote PA in students' lifestyles. Copyright© by the National Institute of Public Health, Prague 2017

Development of a Methodology to Conduct Usability Evaluation for Hand Tools that May Reduce the Amount of Small Parts that are Dropped During Installation while Processing Space Flight Hardware

NASA Technical Reports Server (NTRS)

Miller, Darcy

2000-01-01

Foreign object debris (FOD) is an important concern while processing space flight hardware. FOD can be defined as "The debris that is left in or around flight hardware, where it could cause damage to that flight hardware," (United Space Alliance, 2000). Just one small screw left unintentionally in the wrong place could delay a launch schedule while it is retrieved, increase the cost of processing, or cause a potentially fatal accident. At this time, there is not a single solution to help reduce the number of dropped parts such as screws, bolts, nuts, and washers during installation. Most of the effort is currently focused on training employees and on capturing the parts once they are dropped. Advances in ergonomics and hand tool design suggest that a solution may be possible, in the form of specialty hand tools, which secure the small parts while they are being handled. To assist in the development of these new advances, a test methodology was developed to conduct a usability evaluation of hand tools, while performing tasks with risk of creating FOD. The methodology also includes hardware in the form of a testing board and the small parts that can be installed onto the board during a test. The usability of new hand tools was determined based on efficiency and the number of dropped parts. To validate the methodology, participants were tested while performing a task that is representative of the type of work that may be done when processing space flight hardware. Test participants installed small parts using their hands and two commercially available tools. The participants were from three groups: (1) students, (2) engineers / managers and (3) technicians. The test was conducted to evaluate the differences in performance when using the three installation methods, as well as the difference in performance of the three participant groups.

Efficacy of Danger Ideation Reduction Therapy in Obsessive-Compulsive Disorder Washer with Poor Insight: A Case Study and Literature Review

PubMed Central

Maqbool, Masood; Sengar, K. S.; Vikas; Kumar, Mohit; Uparikar, Premkant Damodhar

2017-01-01

Obsessive-compulsive disorder (OCD) is characterized by obsessions and compulsions. Treatment usually consists of serotonergic medications along with exposure therapies. Danger ideation reduction therapy (DIRT) is an alternative therapy predominantly for washing compulsions and focuses on reduction of danger ideations. DIRT was tried on Ms. S. with a history of OCD for 15 years and improvement was noticed on Yale–Brown Obsessive Compulsive Scale, Padua Inventory, Hamilton Anxiety Rating Scale and Hamilton Depression Rating Scale after 15 sessions of DIRT though she was not fully symptom-free. Thus, DIRT was found to improve OCD symptoms and improved her insight into illness. PMID:28852254

VIBRATION DAMPING AND SHOCK MOUNT

DOEpatents

Stevens, D.J.; Forman, G.W.

1963-12-10

A shock absorbing mount in which vibrations are damped by an interference fit between relatively movable parts of the mount is described. A pair of generally cup-shaped parts or members have skirt portions disposed in an oppositely facing nesting relationship with the skirt of one member frictionally engaging the skirt of the other. The outermost skirt may be slotted to provide spring-like segments which embrace the inner skirt for effecting the interference fit. Belleville washers between the members provide yieldable support for a load carried by the mount. When a resonant frequency of vibration forces acting upon the moumt attains a certain level the kinetic energy of these forces is absorbed by sliding friction between the parts. (AEC)

A dispersive liquid-liquid micellar microextraction for the determination of pharmaceutical compounds in wastewaters using ultra-high-performace liquid chromatography with DAD detection.

PubMed

Montesdeoca-Esponda, Sarah; Mahugo-Santana, Cristina; Sosa-Ferrera, Zoraida; Santana-Rodríguez, José Juan

2015-03-01

A dispersive liquid-liquid micellar microextraction (DLLMME) method coupled with ultra-high-performance liquid chromatography (UHPLC) using Diode Array Detector (DAD) detector was developed for the analysis of five pharmaceutical compounds of different nature in wastewaters. A micellar solution of a surfactant, polidocanol, as extraction solvent (100 μL) and chloroform as dispersive solvent (200 μL) were used to extract and preconcentrate the target analytes. Samples were heated above critical temperature and the cloudy solution was centrifuged. After removing the chloroform, the reduced volume of surfactant was then injected in the UHPLC system. In order to obtain high extraction efficiency, the parameters affecting the liquid-phase microextraction, such as time and temperature extraction, ionic strength and surfactant and organic solvent volume, were optimized using an experimental design. Under the optimized conditions, this procedure allows enrichment factors of up to 47-fold. The detection limit of the method ranged from 0.1 to 2.0 µg/L for the different pharmaceuticals. Relative standard deviations were <26% for all compounds. The procedure was applied to samples from final effluent collected from wastewater treatment plants in Las Palmas de Gran Canaria (Spain), and two compounds were measured at 67 and 113 µg/L in one of them. Copyright © 2014 John Wiley & Sons, Ltd.

A new suturing instrument that allows the use of microsuture at laparoscopy.

PubMed

McComb, P F

1992-04-01

A surgeon at University Hospital-Shaughnessy Site in Vancouver, British Columbia in Canada has used a new suturing instrument that enters the peritoneal cavity to permit microsutures of size 6-0 or less and 75 cm in length during laparoscopy. Surgeons can use this instrument to perform female sterilizations as well as removal of the gall gladder and appendix and repair of the bowel, bladder, and ureteric injuries. As of April 1992, the suturing instrument was not yet commercially available. It consists of a partial hollow 30 cm x 2 mm (inside diameter) tube with the end that does not enter the peritoneal cavity being occluded. The suturing instrument enters the peritoneal cavity via a standard 5 mm deflection valved trocar sleeve with a 3 mm reduction sleeve or with a 3 mm inside diameter occlusive rubber washer instead of the standard 5 mm washer. The suture must have sufficient tensile strength and have low coefficients for static and for sliding surface frictions. Once the suture and needle are inside the body, forceps which have entered via another cannula detach them from the suturing instrument. A 3 mm laproscopic needle driver replaces the suturing instrument at this point. The surgeon guides the needle through the intended tissues and then withdrawn with the needle driver through the 5 mm sleeve. The surgeon ties the knot outside the body and slides it down the length of the suture to apply it to the tissue. He/she repeats this 1 more time. Scissors inserted through the other opening then cut the suture. Once mastered, this process takes only a few minutes to complete. In all 11 cases or restoration of uterine tube patency done by the surgeon in Vancouver using the new technique, tubal patency has not been hindered. 2 assessed sterilization reversals have been successful.

Localization of quenches and mechanical disturbances in the Mu2e transport solenoid prototype using acoustic emission technique

DOE PAGES

Marchevsky, M.; Ambrosio, G.; Lamm, M.; ...

2016-02-12

Acoustic emission (AE) detection is a noninvasive technique allowing the localization of the mechanical events and quenches in superconducting magnets. Application of the AE technique is especially advantageous in situations where magnet integrity can be jeopardized by the use of voltage taps or inductive pickup coils. As the prototype module of the transport solenoid (TS) for the Mu2e experiment at Fermilab represents such a special case, we have developed a dedicated six-channel AE detection system and accompanying software aimed at localizing mechanical events during the coil cold testing. The AE sensors based on transversely polarized piezoceramic washers combined with cryogenicmore » preamplifiers were mounted at the outer surface of the solenoid aluminum shell, with a 60° angular step around the circumference. Acoustic signals were simultaneously acquired at a rate of 500 kS/s, prefiltered and sorted based on their arrival time. Next, based on the arrival timing, angular and axial coordinates of the AE sources within the magnet structure were calculated. Furthermore, we present AE measurement results obtained during cooldown, spot heater firing, and spontaneous quenching of the Mu2e TS module prototype and discuss their relevance for mechanical stability assessment and quench localization.« less

Do Heat Pump Clothes Dryers Make Sense for the U.S. Market

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyers, Steve; Franco, Victor; Lekov, Alex

Heat pump clothes dryers (HPCDs) can be as much as 50percent more energy-efficient than conventional electric resistance clothes dryers, and therefore have the potential to save substantial amounts of electricity. While not currently available in the U.S., there are manufacturers in Europe and Japan that produce units for those markets. Drawing on analysis conducted for the U.S. Department of Energy's (DOE) current rulemaking on amended standards for clothes dryers, this paper evaluates the cost-effectiveness of HPCDs in American homes, as well as the national impact analysis for different market share scenarios. In order to get an accurate measurement of realmore » energy savings potential, the paper offers a new energy use calculation methodology that takes into account the most current data on clothes washer cycles, clothes dryer usage frequency, remaining moisture content, and load weight per cycle, which is very different from current test procedure values. Using the above methodology along with product cost estimates developed by DOE, the paper presents the results of a life-cycle cost analysis of the adoption of HPCDs in a representative sample of American homes. The results show that HPCDs have positive economic benefits only for households with high clothes dryer usage or for households with high electricity prices and moderately high utilization.« less

Impedance-Based Pre-Stress Monitoring of Rock Bolts Using a Piezoceramic-Based Smart Washer—A Feasibility Study

PubMed Central

Wang, Bo; Huo, Linsheng; Chen, Dongdong; Li, Weijie; Song, Gangbing

2017-01-01

Pre-stress degradation or looseness of rock bolts in mining or tunnel engineering threatens the stability and reliability of the structures. In this paper, an innovative piezoelectric device named a “smart washer” with the impedance method is proposed with the aim of developing a real-time device to monitor the pre-stress level of rock bolts. The proposed method was verified through tests on a rock bolt specimen. By applying high-frequency sweep excitations (typically >30 kHz) to the smart washer that was installed on the rock bolt specimen, we observed that the variation in impedance signatures indicated the rock bolt pre-stress status. With the degradation of rock bolt pre-stress, the frequency in the dominating peak of the real part of the electrical impedance signature increased. To quantify the effectiveness of the proposed technique, a normalized root mean square deviation (RMSD) index was developed to evaluate the degradation level of the rock bolt pre-stress. The experimental results demonstrated that the normalized RMSD-based looseness index, which was computed from the impedance value detected by the “smart washer”, increased with loss of the pre-stress of the rock bolt. Therefore, the proposed method can effectively detect the degradation of rock bolt pre-stress, as demonstrated by experiments. PMID:28134811

A Guillemin type E pulse forming network as the driver for a pulsed, high density plasma source.

PubMed

Rathod, Priyavandna J; Anitha, V P; Sholapurwala, Z H; Saxena, Y C

2014-06-01

A Guillemin type E pulse forming network (PFN) has been designed, developed, and tested for its application in generating high density (~1 × 10(18) m(-3)) plasmas. In the present study, plasma thus generated is utilized to investigate the interaction of high power microwaves (HPMs) with plasma in an experimental architecture known as SYMPLE (System for Microwave PLasma Experiment). Plasma discharges of ~100 μs (max) duration are to be produced, by delivering energy of 5 kJ stored in a PFN to the plasma source, a washer gun. The output of the PFN, in terms of its rise time, flat top and amplitude, needs to be tailored, depending on the experimental requirements. An ignitron (NL8900) trigger generator (ITG) is developed in-house to control the PFN discharge through the gun. This ITG is also to be used in a circuit that synchronizes the HPM and plasma shots, to ensure that HPM-plasma interaction takes place during a temporal regime where appropriate parametric conditions are satisfied. Hence it is necessary to retain the jitter within ±2.5 μs. Further, requirement on plasma quiescence (~10%) necessitates maintaining the ripple within 5%. The developmental work of the PFN, keeping in view the above criteria and the test results, is presented in this paper. The parameters of the PFN have been analytically approximated and verified with PSPICE simulation. The test results presented include rise time ~5-8 μs, flat top variable in the range 20-100 μs, ripple within ~1.5%, and jitter within ±2.5 μs, producing quiescent (<10%) plasma discharge meeting the experimental requirements.

Bacterial Survival in Laundered Fabrics

PubMed Central

Walter, William G.; Schillinger, John E.

1975-01-01

Bacterial survival was determined in linens (i) inoculated with Staphylococcus aureus (ii), taken from hospital isolation patients' beds, and (iii) used by students in their homes. Two different washers using temperatures of 38, 49, 54 and 60 C, respectively, for different times were employed along with a commercial tumbler dryer. Findings, after macerating the linens in a Waring blender and enumerating on nonselective media, indicate that acceptable levels of survivors can be achieved in motel and hotel linens by an 8- to 10-min wash cycle at 54 C followed by adequate drying. However, it is recommended that a wash cycle with 60 C for 10 to 13 min be employed for linens in health care factilities. The microbial significance of various laundering practices is discussed. PMID:1090256

The mechanics of endoscope disinfection.

PubMed

Babb, J R; Bradley, C R

1991-06-01

The decontamination of flexible fibreoptic endoscopes has considerably improved in recent years. This is mainly due to the introduction of instruments with more accessible channels, the use of automated washer disinfectors and a greater awareness of the problems associated with disinfection. Unfortunately the most widely used and effective disinfectant is 2% glutaraldehyde and this is toxic, irritant and sensitizing. With the implementation of Control of Substances Hazardous to Health legislation, strict environmental controls are required to reduce skin contact and vapour inhalation. Alcohol is probably the most suitable alternative disinfectant at present but it is flammable and cannot be used in automated systems. Other agents are either insufficiently effective or corrosive. Autoclavable or heat tolerant rigid endoscopes are now available but flexible endoscopes will not tolerate heat disinfection temperatures.

Scoping Report: Advanced Technologies for Multi-Load Washers in Hospitality and Healthcare

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, Graham B.; Boyd, Brian K.; Petersen, Joseph M.

The purpose of this demonstration project is to quantify the energy savings and water efficiency potential of commercial laundry wastewater recycling systems and low-temperature detergent supply systems to help promote the adoption of these technologies in the commercial sector. This project will create a set of technical specifications for efficient multi-load laundry systems (both new and retrofit) tailored for specific applications and/or sectors (e.g., hospitality, health care). The specifications will be vetted with the appropriate Better Buildings Alliance (BBA) members (e.g., Commercial Real Estate Energy Alliance, Hospital Energy Alliance), finalized, published, and disseminated to enable widespread technology transfer in themore » industry and specifically among BBA partners.« less

Landing gear energy absorption system

NASA Technical Reports Server (NTRS)

Hansen, Christopher P. (Inventor)

1994-01-01

A landing pad system is described for absorbing horizontal and vertical impact forces upon engagement with a landing surface where circumferentially arranged landing struts respectively have a clevis which receives a slidable rod member and where the upper portion of a slidable rod member is coupled to the clevis by friction washers which are force fit onto the rod member to provide for controlled constant force energy absorption when the rod member moves relative to the clevis. The lower end of the friction rod is pivotally attached by a ball and socket to a support plate where the support plate is arranged to slide in a transverse direction relative to a housing which contains an energy absorption material for absorbing energy in a transverse direction.

In Situ Materials Study in Hot Hydrothermal Vent Fluid

NASA Astrophysics Data System (ADS)

Holland, P. M.; Schindele, W. J.; Holland, C. E.; Lilley, M. D.; Olson, E. J.

2004-12-01

We are developing methods and technology for in situ sampling and analysis of volatiles from hot hydrothermal vent fluids inside the mixing boundary. These fluids can reach temperatures of up to 400° C and are known to be corrosive to most materials. While titanium has been the material of choice for contact with these fluids, we wanted to assess whether other materials, such as Hastelloy or nickel might be suitable for in situ sampling from hydrothermal vents. For the present study, small (1/16" o.d.) tubes of chemically pure titanium, Hastelloy C, and Nickel 200 were prepared, using 316 stainless steel as a control. These were placed in an assembly with other test items, and inserted into the hydrothermal vent Sully in the Main Endeavor Field on the Juan de Fuca Plate in June 2003 by the Jason II ROV operated from the R/V Thompson. The assembly was retrieved 46 days later after exposure to approximately 360° C hydrothermal vent fluid at a depth of 2200 m. Inspection showed the stainless steel to be completely eroded away and nickel to be extensively corroded, however both the Hastelloy and titanium tubes were in excellent condition with the 0.030" i.d. passages in the tubes remaining open. Other test items included a miniature titanium filtered inlet fitting containing an 80 mesh titanium screen made of 0.004" (0.1 mm) chemically pure titanium wire, an Inconel washer and a sapphire ball. Apart from some discoloration, there appeared to be no significant degradation in these materials apart from signs of etching on the sapphire.

Assessment of the Impacts of Standards and Labeling Programs inMexico (four products).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, Itha; Pulido, Henry; McNeil, Michael A.

2007-06-12

This study analyzes impacts from energy efficiency standards and labeling in Mexico from 1994 through 2005 for four major products: household refrigerators, room air conditioners, three-phase (squirrel cage) induction motors, and clothes washers. It is a retrospective analysis, seeking to assess verified impacts on product efficiency in the Mexican market in the first ten years after standards were implemented. Such an analysis allows the Mexican government to compare actual to originally forecast program benefits. In addition, it provides an extremely valuable benchmark for other countries considering standards, and to the energy policy community as a whole. The methodology for evaluationmore » begins with historical test data taken for a large number of models of each product type between 1994 and 2005. The pre-standard efficiency of models in 1994 is taken as a baseline throughout the analysis. Model efficiency data were provided by an independent certification laboratory (ANCE), which tested products as part of the certification and enforcement mechanism defined by the standards program. Using this data, together with economic and market data provided by both government and private sector sources, the analysis considers several types of national level program impacts. These include: Energy savings; Environmental (emissions) impacts, and Net financial impacts to consumers, manufacturers and utilities. Energy savings impacts are calculated using the same methodology as the original projections, allowing a comparison. Other impacts are calculated using a robust and sophisticated methodology developed by the Instituto de Investigaciones Electricas (IIE) and Lawrence Berkeley National Laboratory (LBNL), in a collaboration supported by the Collaborative Labeling and Standards Program (CLASP).« less

Effects of sintering temperature on the microstructural evolution and wear behavior of WCp reinforced Ni-based coatings

NASA Astrophysics Data System (ADS)

Chen, Chuan-hui; Bai, Yang; Ye, Xu-chu

2014-12-01

This article focuses on the microstructural evolution and wear behavior of 50wt%WC reinforced Ni-based composites prepared onto 304 stainless steel substrates by vacuum sintering at different sintering temperatures. The microstructure and chemical composition of the coatings were investigated by X-ray diffraction (XRD), differential thermal analysis (DTA), scanning and transmission electron microscopy (SEM and TEM) equipped with energy-dispersive X-ray spectroscopy (EDS). The wear resistance of the coatings was tested by thrust washer testing. The mechanisms of the decomposition, dissolution, and precipitation of primary carbides, and their influences on the wear resistance have been discussed. The results indicate that the coating sintered at 1175°C is composed of fine WC particles, coarse M6C (M=Ni, Fe, Co, etc.) carbides, and discrete borides dispersed in solid solution. Upon increasing the sintering temperature to 1225°C, the microstructure reveals few incompletely dissolved WC particles trapped in larger M6C, Cr-rich lamellar M23C6, and M3C2 in the austenite matrix. M23C6 and M3C2 precipitates are formed in both the γ/M6C grain boundary and the matrix. These large-sized and lamellar brittle phases tend to weaken the wear resistance of the composite coatings. The wear behavior is controlled simultaneously by both abrasive wear and adhesive wear. Among them, abrasive wear plays a major role in the wear process of the coating sintered at 1175°C, while the effect of adhesive wear is predominant in the coating sintered at 1225°C.

Trade study comparing specimen chamber servicing methods for the Space Station Centrifuge Facility

NASA Technical Reports Server (NTRS)

Calvisi, Michael L.; Sun, Sidney C.

1991-01-01

The Specimen Chamber Service Unit, a component of the Space Station Centrifuge Facility, must provide a clean enclosure on a continuing basis for the facility's plant, rodent and primate specimens. The specimen chambers can become soiled and can require periodic servicing to maintain a clean environment for the specimens. Two methods of servicing the specimen chambers are discussed: washing the chambers with an on-board washer, or disposing of the soiled chambers and replacing them with clean ones. Many of these issues are addressed by developing several servicing options, using either cleaning or replacement as the method of providing clean specimen chambers, and then evaluating each option according to a set of established quantitative and qualitative criteria. Disposing and replacing the Specimen Chambers is preferable to washing them.

Double arch mirror study. Part 1: Preliminary engineering report

NASA Technical Reports Server (NTRS)

Vukobratovich, D.; Hillman, D.

1983-01-01

In the proposed design, the NASA AMES 20-in double arch mirror is supported by three clamp and flexure assemblies. The mirror clamp consists of a T-shaped Invar-36 member that goes into a similarly shaped socket in the back of the mirror. The mirror socket is made oversize and contacts the clamp only along the conical surface. The clamp is preloaded by a spring washer and pulls the mirror into contact with the flexure. The clamp is then inserted into the mirror socket through a cutout, is rotated 90 deg, and is then pinned in place. Loading conditions considered in socket design are discussed as well as stress in the socket and clamp. Flexure geometry and stress are examined as well as the effects of flexure error and of mirror cell error.

Lead magnesium niobate actuator for micropositioning

DOEpatents

Swift, Charles D.; Bergum, John W.

1994-01-01

An improved lead magnesium niobate actuator is disclosed comprising a cylindrical lead magnesium niobate crystal stack mounted in a cylindrical casing wherein a bias means, such as one or more belleville washers, is located between one end of the crystal stack and a partially closed end of the casing; and adjustment means are provided which bear against the opposite end of the crystal stack, whereby an adjustable compressive force is constantly applied against the crystal stack, whether the crystal stack is actuated in an extended position, or is in an unactuated contracted position. In a preferred embodiment, cooling ports are provided for the circulation of coolant in the actuator to cool the crystal stack, and provision is made for removal and replacement of the crystal stack without disconnecting the actuator from the external device being actuated.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romero, Antonio; Oweis, Salah; Chagnon, Guy

An electrochemical cell having a spiral winding around a central core, wherein the central core is provided with longitudinal grooves on its outer surface to facilitate electrolyte filing and accommodate overpressure. The core itself improves dissipation of heat generated along the center of the cell, and the hollow core design allows the cell core to have a larger radius, permitting the "jelly roll" winding to begin at a larger radius and thereby facilitate the initial turns of the winding by decreasing the amount of bending required of the electrode laminate at the beginning of the winding operation. The hollow coremore » also provides mechanical support end-to-end. A pair of washers are used at each end of the cell to sandwich current collection tabs in a manner that improves electrical and thermal conductivity while also providing structural integrity.« less

DOE Zero Energy Ready Home Case Study, Weiss Building & Development, LLC., System Home, River Forest, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The Passive House Challenge Home located in River Forest, Illinois, is a 5-bedroom, 4.5-bath, 3,600 ft2 two-story home (plus basement) that costs about $237 less per month to operate than a similar sized home built to the 2009 IECC. For a home with no solar photovoltaic panels installed, it scored an amazingly low 27 on the Home Energy Rating System (HERS) score.An ENERGY STAR-rated dishwasher, clothes washer, and refrigerator; an induction cooktop, condensing clothes dryer, and LED lighting are among the energy-saving devices inside the home. All plumbing fixtures comply with EPA WaterSense criteria. The home was awarded a 2013more » Housing Innovation Award in the "systems builder" category.« less

KSC-08pd3742

NASA Image and Video Library

2008-11-19

CAPE CANAVERAL, Fla. – At the Parachute Refurbishment Facility at NASA's Kennedy Space Center in Florida, workers begin hanging the parachutes recovered from sea after the launch of space shuttle Endeavour on the STS-126 mission onto a monorail system. The parachutes are used to slow the descent of the solid rocket boosters that are jettisoned during liftoff. The monorail will transport each parachute into a 30,000-gallon washer and a huge dryer heated with 140-degree air at 13,000 cubic feet per minute One pilot, one drogue and three main canopies per booster slow the booster’s fall from about 360 mph to 50 mph. After the chutes are cleaned and repaired, they must be carefully packed into their bags so they will deploy correctly the next time they are used. Photo credit: NASA/Jim Grossmann

KSC-08pd3743

NASA Image and Video Library

2008-11-19

CAPE CANAVERAL, Fla. – At the Parachute Refurbishment Facility at NASA's Kennedy Space Center in Florida, workers begin hanging the parachutes recovered from sea after the launch of space shuttle Endeavour on the STS-126 mission onto a monorail system. The parachutes are used to slow the descent of the solid rocket boosters that are jettisoned during liftoff. The monorail will transport each parachute into a 30,000-gallon washer and a huge dryer heated with 140-degree air at 13,000 cubic feet per minute. One pilot, one drogue and three main canopies per booster slow the booster’s fall from about 360 mph to 50 mph. After the chutes are cleaned and repaired, they must be carefully packed into their bags so they will deploy correctly the next time they are used. Photo credit: NASA/Jim Grossmann

KSC-08pd3740

NASA Image and Video Library

2008-11-19

CAPE CANAVERAL, Fla. – Parachutes recovered from sea after the launch of space shuttle Endeavour on the STS-126 mission are suspended from a hanging monorail system at the Parachute Refurbishment Facility at NASA's Kennedy Space Center in Florida. The parachutes are used to slow the descent of the solid rocket boosters that are jettisoned during liftoff. The monorail will transport each parachute into a 30,000-gallon washer and a huge dryer heated with 140-degree air at 13,000 cubic feet per minute. One pilot, one drogue and three main canopies per booster slow the booster’s fall from about 360 mph to 50 mph. After the chutes are cleaned and repaired, they must be carefully packed into their bags so they will deploy correctly the next time they are used. Photo credit: NASA/Jim Grossmann

KSC-08pd3747

NASA Image and Video Library

2008-11-19

CAPE CANAVERAL, Fla. – At the Parachute Refurbishment Facility at NASA's Kennedy Space Center in Florida, the parachutes recovered from sea after the launch of space shuttle Endeavour on the STS-126 mission are moved through the 30,000-gallon washer. The parachutes are used to slow the descent of the solid rocket boosters that are jettisoned during liftoff. After washing, the monorail will move the parachutes into a huge dryer heated with 140-degree air at 13,000 cubic feet per minute. One pilot, one drogue and three main canopies per booster slow the booster’s fall from about 360 mph to 50 mph. After the chutes are cleaned and repaired, they must be carefully packed into their bags so they will deploy correctly the next time they are used. Photo credit: NASA/Jim Grossmann

Word Frequency Analysis. MOS: 19D. Skill Levels 1 & 2.

DTIC Science & Technology

1981-05-01

34 I, WAR NINC. I WASHER I WATCHES I WATERS I WE 1, WEAK I WFATll:RPROn F I WEF.STHERPnr-OS I wEDGED I WEEK I WFEKL Y/ I WrfGr) I WE IGH I WELD I WtLOED... fRACKED I. BACK pOLPAO I ACKING - I BA D 4 P ARRAIER I B ASE 7 BAASIC 5 BATTERIES it "BATTERY2 SA 3030 3 nA4517/U 1 88501 ill 76. RE zBEAR 4 BECAUSE 1...I TY I VI CTIl noI V Is fft1i IfVY I vi SIR) v I VISUAL t VOL. I V 26 I WC2 %:,IT MI WIING I wall I RW 1 WATIWR4 12 WRNING 4 WAS 2 WMS as"It WATER 6

A 5 year longitudinal study of water quality for final rinsing in the single chamber washer-disinfector with a reverse osmosis plant.

PubMed

Uetera, Yushi; Kishii, Kozue; Yasuhara, Hiroshi; Kumada, Naohito; Moriya, Kyoji; Saito, Ryoichi; Okazaki, Mitsuhiro; Misawa, Yoshiki; Kawamura, Kunio

2013-01-01

This report deals with the construction and management of the reverse osmosis (RO) water system for final rinsing of surgical instruments in the washer-disinfector. Numerous operational challenges were encountered in our RO water system and these were analyzed utilizing the Ishikawa Fishbone diagram. The aim was to find potential problems and promote preventive system management for RO water. It was found that the measures that existed were inappropriate for preventing contamination in the heat-labile RO water system. The storage tank was found to be significantly contaminated and had to be replaced with a new one equipped with a sampling port and water drainage system. Additional filters and an UV treatment lamp were installed. The whole system disinfection started 1.5 years later using a peracetic acid-based compound after confirming the material compatibility. Operator errors were found when a new water engineer took over the duty from his predecessor. It was also found that there were some deficiencies in the standard operating procedures (SOPs), and that on-the-job training was not enough. The water engineer failed to disinfect the sampling port and water drainage system. The RO membrane had been used for 4 years, even though the SOP standard specified changing it as every 3 years. Various bacteria, such as Rothia mucilaginosa, were cultured from the RO water sampled from the equipment. Because Rothia mucilaginosa is a resident in the oral cavity and upper respiratory tract, it is believed that the bacteria were introduced into the system by the maintenance personnel or working environment. Therefore, the presence of R. mucilaginosa implied the failure of sanitary maintenance procedures. This study suggests that water systems should be designed based on the plans for profound system maintenance. It also suggests that SOP and on-the job training are essential to avoid any operator errors. These results must be carefully considered when either constructing new RO systems or performing maintenance and periodical examination of the equipment. Reverse osmosis (RO) water is used for final rinsing in our washer-disinfector. The authors used the Ishikawa Fishbone diagram to clarify the critical points for optimizing RO water quality. There existed no measures to prevent contamination in the heat-labile RO water system. The storage tank was significantly contaminated and had to be replaced with a new one equipped with a sampling port and water drainage system. Additional filters and an UV treatment lamp were installed. The whole system disinfection started 1.5 years later using a peracetic acid-based compound after confirming the material compatibility. Operator errors occurred when a new water engineer took over the duty from his predecessor. There were neither standard operating procedures (SOPs) nor on-the-job training. The new water engineer had failed to disinfect the sampling port and water drainage system. Rothia mucilaginosa was cultured from the RO water. It is a resident in the oral cavity and upper respiratory tract. This implied the possible failure of sanitary procedures in the system maintenance. The Ishikawa Fishbone diagram was useful for this study. It suggests that water systems should be designed with plans for system maintenance taken into account. It also suggests that SOP and on-the job training are essential in order to avoid operator errors.

Partial entrainment of gravel bars during floods

USGS Publications Warehouse

Konrad, Christopher P.; Booth, Derek B.; Burges, Stephen J.; Montgomery, David R.

2002-01-01

Spatial patterns of bed material entrainment by floods were documented at seven gravel bars using arrays of metal washers (bed tags) placed in the streambed. The observed patterns were used to test a general stochastic model that bed material entrainment is a spatially independent, random process where the probability of entrainment is uniform over a gravel bar and a function of the peak dimensionless shear stress τ0* of the flood. The fraction of tags missing from a gravel bar during a flood, or partial entrainment, had an approximately normal distribution with respect to τ0* with a mean value (50% of the tags entrained) of 0.085 and standard deviation of 0.022 (root‐mean‐square error of 0.09). Variation in partial entrainment for a given τ0* demonstrated the effects of flow conditioning on bed strength, with lower values of partial entrainment after intermediate magnitude floods (0.065 < τ0*< 0.08) than after higher magnitude floods. Although the probability of bed material entrainment was approximately uniform over a gravel bar during individual floods and independent from flood to flood, regions of preferential stability and instability emerged at some bars over the course of a wet season. Deviations from spatially uniform and independent bed material entrainment were most pronounced for reaches with varied flow and in consecutive floods with small to intermediate magnitudes.

Essays on environmental and energy economics

NASA Astrophysics Data System (ADS)

Brucal, Arlan Zandro

This dissertation applies techniques from the expanding field of econometrics to the study of contemporary issues in environmental and resource economics. Three essays are offered that aim to generate meaningful policy implications through econometric analyses of the voluminous data recently becoming available to researchers. The first essay examines how overall price, quality and welfare changed as energy efficiency standards in the US became progressively more stringent between 2001-2011. A novel index-the Constant Quality Price Index (CQPI)-is developed to delineate changes in overall price and quality. Results obtained using point-of-sale data from individual clothes washers sold in the US during the period suggest that standards on washing machines have had at worst a negligible effect on consumer welfare, or at best lowered prices and improved quality for washers. The second essay analyzes the relationship between foreign acquisition and aspects of plant-level environmental performance using micro data from the Indonesian Census of Manufacturing. To establish a causal effect of ownership change, a difference-in-differences approach is combined with coarsened exact matching. A total of 264 acquisition cases between 1983-2001 are considered, where an acquired plant is observed at least a year before and three years after undergoing a change in ownership, and for which a carefully selected control plant exists. Results suggest that FDIs can have positive scale and technique effects on the environmental performance of acquired plants. These effects are especially pronounced for small firms and firms that were relatively inefficient prior to acquisition. The third essay analyzes the impact of oil price shocks on the US economy at the individual state level. The study accounts for the endogeneity of changes in crude oil price, differences among states, and spillover effects with neighboring states. Results suggest that the implications of higher oil prices for a state's economic growth depend on the underlying cause of the oil price change and a state's average production of oil relative to its average consumption. The direct effect of oil price shocks can be either magnified or tempered by spillover effects, which may also explain why regional recessions may occur with certain oil price shocks.

Versatile Clinical Application of the Spike Screw: Direct Anchorage Versus Indirect Anchorage.

PubMed

Kim, Kyung A; Chen, Yu; Kwon, Soon-Yong; Seo, Kyung Won; Park, Ki-Ho; Kim, Seong-Hun

2015-10-01

This article represents clinical application of spike screw, novel design of miniscrew, for direct anchorage and indirect anchorage in orthodontic treatment. Accompanied by easy placement and removal, the spike screw provides good stability for the orthodontic anchorage. The spike screw consists of 6 spikes attached to a washer with laser welded stainless-steel hook that is placed by self-drilling fixation miniscrew. The spike screws were applied to correct malocclusions in patients as follows: traction of impacted canines and protraction of posterior teeth as a direct anchorage and correction of midline discrepancy as an indirect anchorage. For orthodontic traction of impacted canines, spike screws were placed in the mandibular labial mucosal area to create extrusive forces. Afterward, it was utilized for the protraction of posterior teeth. In the second case of the indirect anchorage, spike screw was applied on the midpalatal area to correct midline discrepancy that occurred during orthodontic treatment. The extended hook of a washer was prebended along the curvature of the palate and then secured with a mini screw. The extended hook was bonded to maxillary left first molar. In the first case, the spike screw provided adequate anchorage for the vertical traction of horizontally impacted canine. Since the spike screws were placed in the mandibular anterior lesion, the vertical traction force was applied simply with orthodontic elastics. Also, enough distance was achieved for up-down elastics to work by placing the spike screw in the opposite arch. The force of vertical traction was adjusted with selection of size and force of up-down elastics. Later, it was used to provide anchorage for protraction of mandibular molars without changing orientation of the spike screws. In the second case, the spike screw placed in the midpalatal area was attached to the left first molar and worked as an indirect anchorage. The midline discrepancy was resolved by consolidating the spaces to the left with securing the left first molar location. The novel design of the spike screw permits clinicians to have minimum invasive and easy placement and removal of the appliance while maintaining a good control over tooth movement with improved stability in various clinical cases.

Status of China's Energy Efficiency Standards and Labels for Appliances and International Collaboration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Nan

2008-03-01

China first adopted minimum energy performance standards (MEPS) in 1989. Today, there are standards for a wide range of domestic, commercial and selected industrial equipment. In 1999, China launched a voluntary endorsement label, which has grown to cover over 40 products including water-saving products (See Figure 1). Further, in 2005, China started a mandatory energy information label (also referred to as the 'Energy Label'). Today, the Energy Label is applied to four products including: air conditioners; household refrigerators; clothes washers; and unitary air conditioners (See Figure 2). MEPS and the voluntary endorsement labeling specifications have been updated and revised inmore » order to reflect technology improvements to those products in the market. These programs have had an important impact in reducing energy consumption of appliances in China. Indeed, China has built up a strong infrastructure to develop and implement product standards. Historically, however, the government's primary focus has been on the technical requirements for efficiency performance. Less attention has been paid to monitoring and enforcement with a minimal commitment of resources and little expansion of administrative capacity in this area. Thus, market compliance with both mandatory standards and labeling programs has been questionable and actual energy savings may have been undermined as a result. The establishment of a regularized monitoring system for tracking compliance with the mandatory standard and energy information label in China is a major area for program improvement. Over the years, the Collaborative Labeling and Appliance Standards Program (CLASP) has partnered with several Chinese institutions to promote energy-efficient products in China. CLASP, together with its implementing partner Lawrence Berkeley National Laboratory (LBNL), has assisted China in developing and updating the above-mentioned standards and labeling programs. Because of the increasing need for the development of a monitoring system to track compliance with standards and labeling, CLASP, with support from Japan's Ministry of Economy, Trade and Industry (METI), has expanded its ongoing collaboration with the China National Institute of Standards (CNIS) to include enforcement and monitoring. CNIS has already begun working on the issue of compliance. CNIS has conducted modest sample testing in 2006 for refrigerators, freezers and room air-conditioners, and repeated the same task in 2007 with a similar sample size for three products (refrigerators, freezers, air-conditioners and clothes washers). And, CNIS, with technical support from LBNL, has analyzed the data collected through testing. At the same time, parallel effort has also been paid to look at the potential impact of the label to 2020. In conjunction with CNIS, CLASP technical experts reviewed the standards development timeline of the four products currently subject to the mandatory energy information label. CLASP, with the support of METI/IEEJ, collaborated with CNIS to develop the efficiency grades, providing: technical input to the process; comment and advice on particular technical issues; as well as evaluation of the results. In addition, in order to effectively evaluate the impact of the label on China's market, CLASP further provided assistance to CNIS to collect data on both the efficiency distribution and product volume distribution of refrigerators on the market. This short report summarizes the status of Standards and Labeling program, current enforcement and monitoring mechanism in China, and states the importance of international collaborations.« less

Short communication: Automatic washing of hooves can help control digital dermatitis in dairy cows.

PubMed

Thomsen, Peter T; Ersbøll, Annette Kjær; Sørensen, Jan Tind

2012-12-01

The objectives of this study were to develop and test a system for automatic washing of the hooves of dairy cows and to evaluate the effect of frequent automatic washing on the prevalence of digital dermatitis (DD). An automatic hoof washer was developed in an experimental dairy herd and tested in 6 commercial dairy herds in 2 experiments (1 and 2). In the experimental herd, automatic hoof washing resulted in cleaner hooves. In experiments 1 and 2, cows were washed after each milking on the left side only, leaving the right side unwashed as a within-cow control. In experiment 1, hooves were washed with a water and 0.4% soap solution. In experiment 2, hooves were washed with water only. In each experiment, DD was scored in a hoof-trimming chute approximately 60 d after the start of hoof washing. Data were analyzed using a generalized linear mixed model. The outcome was the DD status of each leg (DD positive or DD negative). Herd and cow within herd were included as random effects, and treatment (washing or control) was included as a fixed effect. The statistical analyses showed that the odds ratio of having DD was 1.48 in the control leg compared with the washed leg in experiment 1. In experiment 2, the odds ratio of having DD was 1.27 in the control leg compared with the washed leg. We concluded that automatic washing of hooves with water and soap can help decrease the prevalence of DD in commercial dairy herds. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Structural Analysis of the Redesigned Ice/Frost Ramp Bracket

NASA Technical Reports Server (NTRS)

Phillips, D. R.; Dawicke, D. S.; Gentz, S. J.; Roberts, P. W.; Raju, I. S.

2007-01-01

This paper describes the interim structural analysis of a redesigned Ice/Frost Ramp bracket for the Space Shuttle External Tank (ET). The proposed redesigned bracket consists of mounts for attachment to the ET wall, supports for the electronic/instrument cables and propellant repressurization lines that run along the ET, an upper plate, a lower plate, and complex bolted connections. The eight nominal bolted connections are considered critical in the summarized structural analysis. Each bolted connection contains a bolt, a nut, four washers, and a non-metallic spacer and block that are designed for thermal insulation. A three-dimensional (3D) finite element model of the bracket is developed using solid 10-node tetrahedral elements. The loading provided by the ET Project is used in the analysis. Because of the complexities associated with accurately modeling the bolted connections in the bracket, the analysis is performed using a global/local analysis procedure. The finite element analysis of the bracket identifies one of the eight bolted connections as having high stress concentrations. A local area of the bracket surrounding this bolted connection is extracted from the global model and used as a local model. Within the local model, the various components of the bolted connection are refined, and contact is introduced along the appropriate interfaces determined by the analysts. The deformations from the global model are applied as boundary conditions to the local model. The results from the global/local analysis show that while the stresses in the bolts are well within yield, the spacers fail due to compression. The primary objective of the interim structural analysis is to show concept viability for static thermal testing. The proposed design concept would undergo continued design optimization to address the identified analytical assumptions and concept shortcomings, assuming successful thermal testing.