MEASUREMENT OF WASTE LOADING IN SALTSTONE
DOE Office of Scientific and Technical Information (OSTI.GOV)
Harbour, J; Vickie Williams, V
2008-07-18
One of the goals of the Saltstone variability study is to identify the operational and compositional variables that control or influence the important processing and performance properties of Saltstone grout mixtures. One of those properties of importance is the Waste Loading (WL) of the decontaminated salt solution (DSS) in the Saltstone waste form. Waste loading is a measure of the amount of waste that can be incorporated within a waste form. The value of the Saltstone waste loading ultimately determines the number of vaults that will be required to disposition all of the DSS. In this report, the waste loadingmore » is defined as the volume in milliliters of DSS per liter of Saltstone waste form. The two most important parameters that determine waste loading for Saltstone are water to cementitious material (w/cm) ratio and the cured grout density. Data are provided that show the dependence of waste loading on the w/cm ratio for a fixed DSS composition using the current premix material (45% Blast Furnace Slag (BFS), 45% Fly Ash (FA) and 10% Ordinary Portland Cement (OPC)). The impact of cured grout density on waste loading was also demonstrated. Mixes (at 0.60 w/cm) made with a Modular Caustic side extraction Unit (MCU) simulant and either OPC or BFS have higher cured grout densities than mixes made with premix and increase the WL to 709 mL/L for the OPC mix and 689 mL/L for the BFS mix versus the value of 653 mL/L for MCU in premix at 0.60 w/cm ratio. Bleed liquid reduces the waste loading and lowers the effective w/cm ratio of Saltstone. A method is presented (and will be used in future tasks) for correcting the waste loading and the w/cm ratio of the as-batched mixes in those cases where bleed liquid is present. For example, the Deliquification, Dissolution and Adjustment (DDA) mix at an as-batched 0.60 w/cm ratio, when corrected for % bleed, gives a mix with a 0.55 w/cm ratio and a WL that has been reduced from 662 to 625 mL/L. An example is provided that demonstrated the quantitative impact of WL on the number of cells (each Saltstone vault contains two cells) required to disposition all of the {approx}100 million gallons of DSS available in the tanks. This calculation revealed that the number of cells required over the range of 0.48 to 0.62 w/cm ratio (equivalent to a WL range of 591 to 666 mL/L) varies from 65 to 57 cells (33 to 29 vaults). The intent of this oversimplified example was to show the range of variation in vaults expected due to w/cm ratio rather than to estimate the actual number of vaults required. There is a tradeoff between the waste loading and the processing and performance properties of Saltstone. The performance properties improve in general as the w/cm ratio decreases whereas the waste loading is reduced at lower w/cm ratios resulting in a larger number of Saltstone vaults. The final performance and processing requirements of Saltstone will determine the maximum waste loading achievable.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Peeler, D.; Edwards, T.
High-level waste (HLW) throughput (i.e., the amount of waste processed per unit of time) is primarily a function of two critical parameters: waste loading (WL) and melt rate. For the Defense Waste Processing Facility (DWPF), increasing HLW throughput would significantly reduce the overall mission life cycle costs for the Department of Energy (DOE). Significant increases in waste throughput have been achieved at DWPF since initial radioactive operations began in 1996. Key technical and operational initiatives that supported increased waste throughput included improvements in facility attainment, the Chemical Processing Cell (CPC) flowsheet, process control models and frit formulations. As a resultmore » of these key initiatives, DWPF increased WLs from a nominal 28% for Sludge Batch 2 (SB2) to {approx}34 to 38% for SB3 through SB6 while maintaining or slightly improving canister fill times. Although considerable improvements in waste throughput have been obtained, future contractual waste loading targets are nominally 40%, while canister production rates are also expected to increase (to a rate of 325 to 400 canisters per year). Although implementation of bubblers have made a positive impact on increasing melt rate for recent sludge batches targeting WLs in the mid30s, higher WLs will ultimately make the feeds to DWPF more challenging to process. Savannah River Remediation (SRR) recently requested the Savannah River National Laboratory (SRNL) to perform a paper study assessment using future sludge projections to evaluate whether the current Process Composition Control System (PCCS) algorithms would provide projected operating windows to allow future contractual WL targets to be met. More specifically, the objective of this study was to evaluate future sludge batch projections (based on Revision 16 of the HLW Systems Plan) with respect to projected operating windows using current PCCS models and associated constraints. Based on the assessments, the waste loading interval over which a glass system (i.e., a projected sludge composition with a candidate frit) is predicted to be acceptable can be defined (i.e., the projected operating window) which will provide insight into the ability to meet future contractual WL obligations. In this study, future contractual WL obligations are assumed to be 40%, which is the goal after all flowsheet enhancements have been implemented to support DWPF operations. For a system to be considered acceptable, candidate frits must be identified that provide access to at least 40% WL while accounting for potential variation in the sludge resulting from differences in batch-to-batch transfers into the Sludge Receipt and Adjustment Tank (SRAT) and/or analytical uncertainties. In more general terms, this study will assess whether or not the current glass formulation strategy (based on the use of the Nominal and Variation Stage assessments) and current PCCS models will allow access to compositional regions required to targeted higher WLs for future operations. Some of the key questions to be considered in this study include: (1) If higher WLs are attainable with current process control models, are the models valid in these compositional regions? If the higher WL glass regions are outside current model development or validation ranges, is there existing data that could be used to demonstrate model applicability (or lack thereof)? If not, experimental data may be required to revise current models or serve as validation data with the existing models. (2) Are there compositional trends in frit space that are required by the PCCS models to obtain access to these higher WLs? If so, are there potential issues with the compositions of the associated frits (e.g., limitations on the B{sub 2}O{sub 3} and/or Li{sub 2}O concentrations) as they are compared to model development/validation ranges or to the term 'borosilicate' glass? If limitations on the frit compositional range are realized, what is the impact of these restrictions on other glass properties such as the ability to suppress nepheline formation or influence melt rate? The model based assessments being performed make the assumption that the process control models are applicable over the glass compositional regions being evaluated. Although the glass compositional region of interest is ultimately defined by the specific frit, sludge, and WL interval used, there is no prescreening of these compositional regions with respect to the model development or validation ranges which is consistent with current DWPF operations.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Peeler, D; Tommy Edwards, T; Kevin Fox, K
The Savannah River National Laboratory (SRNL) has developed, and continues to enhance, its integrated capability to evaluate the impact of proposed sludge preparation plans on the Defense Waste Processing Facility's (DWPF's) operation. One of the components of this integrated capability focuses on frit development which identifies a viable frit or frits for each sludge option being contemplated for DWPF processing. A frit is considered viable if its composition allows for economic fabrication and if, when it is combined with the sludge option under consideration, the DWPF property/composition models (the models of DWPF's Product Composition Control System (PCCS)) indicate that themore » combination has the potential for an operating window (a waste loading (WL) interval over which the sludge/frit glass system satisfies processability and durability constraints) that would allow DWPF to meet its goals for waste loading and canister production. This report documents the results of SRNL's efforts to identify candidate frit compositions and corresponding predicted operating windows (defined in terms of WL intervals) for the February 2007 compositional projection of Sludge Batch 4 (SB4) developed by the Liquid Waste Organization (LWO). The nominal compositional projection was used to assess projected operating windows (in terms of a waste loading interval over which all predicted properties were classified as acceptable) for various frits, evaluate the applicability of the 0.6 wt% SO{sub 4}{sup =} PCCS limit to the glass systems of interest, and determine the impact (or lack thereof) to the previous SB4 variability studies. It should be mentioned that the information from this report will be coupled with assessments of melt rate to recommend a frit for SB4 processing. The results of this paper study suggest that candidate frits are available to process the nominal SB4 composition over attractive waste loadings of interest to DWPF. Specifically, two primary candidate frits for SB4 processing, Frit 510 and Frit 418, have projected operating windows that should allow for successful processing at DWPF. While Frit 418 has been utilized at DWPF, Frit 510 is a higher B{sub 2}O{sub 3} based frit which could lead to improvements in melt rate. These frits provide relatively large operating windows and demonstrate robustness to possible sludge compositional variation while avoiding potential nepheline formation issues. In addition, assessments of SO{sub 4}{sup =} solubility indicate that the 0.6 wt% SO{sub 4}{sup =} limit in PCCS is applicable for the Frit 418 and the Frit 510 based SB4 glass systems.« less
RESULTS OF THE FY09 ENHANCED DOE HIGH LEVEL WASTE MELTER THROUGHPUT STUDIES AT SRNL
DOE Office of Scientific and Technical Information (OSTI.GOV)
Johnson, F.; Edwards, T.
2010-06-23
High-level waste (HLW) throughput (i.e., the amount of waste processed per unit time) is a function of two critical parameters: waste loading (WL) and melt rate. For the Waste Treatment and Immobilization Plant (WTP) at the Hanford Site and the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), increasing HLW throughput would significantly reduce the overall mission life cycle costs for the Department of Energy (DOE). The objective of this task is to develop data, assess property models, and refine or develop the necessary models to support increased WL of HLW at SRS. It is a continuationmore » of the studies initiated in FY07, but is under the specific guidance of a Task Change Request (TCR)/Work Authorization received from DOE headquarters (Project Number RV071301). Using the data generated in FY07, FY08 and historical data, two test matrices (60 glasses total) were developed at the Savannah River National Laboratory (SRNL) in order to generate data in broader compositional regions. These glasses were fabricated and characterized using chemical composition analysis, X-ray Diffraction (XRD), viscosity, liquidus temperature (TL) measurement and durability as defined by the Product Consistency Test (PCT). The results of this study are summarized below: (1) In general, the current durability model predicts the durabilities of higher waste loading glasses quite well. A few of the glasses exhibited poorer durability than predicted. (2) Some of the glasses exhibited anomalous behavior with respect to durability (normalized leachate for boron (NL [B])). The quenched samples of FY09EM21-02, -07 and -21 contained no nepheline or other wasteform affecting crystals, but have unacceptable NL [B] values (> 10 g/L). The ccc sample of FY09EM21-07 has a NL [B] value that is more than one half the value of the quenched sample. These glasses also have lower concentrations of Al{sub 2}O{sub 3} and SiO{sub 2}. (3) Five of the ccc samples (EM-13, -14, -15, -29 and -30) completely crystallized with both magnetite and nepheline, and still had extremely low NL [B] values. These particular glasses have more CaO present than any of the other glasses in the matrix. It appears that while all of the glasses contain nepheline, the NL [B] values decrease as the CaO concentration increases from 2.3 wt% to 4.3 wt%. A different form of nepheline may be created at higher concentrations of CaO that does not significantly reduce glass durability. (4) The T{sub L} model appears to be under-predicting the measured values of higher waste loading glasses. Trends in T{sub L} with composition are not evident in the data from these studies. (5) A small number of glasses in the FY09 matrix have measured viscosities that are much lower than the viscosity range over which the current model was developed. The decrease in viscosity is due to a higher concentration of non-bridging oxygens (NBO). A high iron concentration is the cause of the increase in NBO. Durability, viscosity and T{sub L} data collected during FY07 and FY09 that specifically targeted higher waste loading glasses was compiled and assessed. It appears that additional data may be required to expand the coverage of the T{sub L} and viscosity models for higher waste loading glasses. In general, the compositional regions of the higher waste loading glasses are very different than those used to develop these models. On the other hand, the current durability model seems to be applicable to the new data. At this time, there is no evidence to modify this model; however additional experimental studies should be conducted to determine the cause of the anomalous durability data.« less
Reconfirmation of frit 803 based on the January 2016 sludge batch 9 reprojection
DOE Office of Scientific and Technical Information (OSTI.GOV)
Johnson, F.; Edwards, T.
2016-02-10
On January 11, 2016, Savannah River Remediation (SRR) provided the Savannah River National Laboratory (SRNL) with a Sludge Batch 9 (SB9) reprojection that was developed from the analyzed composition of a Tank 51 sample. This sample was collected after field washing had been completed in Tank 51 to support the alternate reductant task. Based on this reprojection, Frit 803 is still a viable option for the processing of SB9 under sludge-only operations and coupled (Actinide Removal Process (ARP) product with and without monosodium titanate (MST)) operations. The maximum projected volumes of ARP product that can be transferred from the Precipitatemore » Reactor Feed Tank (PRFT) per Sludge Receipt and Adjustment Tank (SRAT) batch and the resulting Na 2O concentrations in the SRAT for coupled operations were determined. The Na 2O concentrations in the SRAT resulting from the maximum projected ARP product transfer volumes are consistent with those from the previous assessments that were based on the August 2015 projections. Regardless of the presence or absence of MST in the ARP product, the contribution of Na 2O to the resulting glass will be similar at the same waste loading (WL). These projected volumes of ARP product are not anticipated to be an issue for SB9. The actual transfer volumes from the PRFT to the SRAT are determined based upon the analyzed Na 2O concentrations in the PRFT samples, which has resulted in larger transfer volumes than those allowed by the projections for Sludge Batch 8 (SB8). An operating window of 32-40% WL around the nominal WL of 36% is achievable for both sludge-only and coupled operations; however, each of the glass systems studied does become limited by waste form affecting constraints (durability) at higher volumes of ARP product and WLs of 41-42%.« less
Relating physician's workload with errors during radiation therapy planning.
Mazur, Lukasz M; Mosaly, Prithima R; Hoyle, Lesley M; Jones, Ellen L; Chera, Bhishamjit S; Marks, Lawrence B
2014-01-01
To relate subjective workload (WL) levels to errors for routine clinical tasks. Nine physicians (4 faculty and 5 residents) each performed 3 radiation therapy planning cases. The WL levels were subjectively assessed using National Aeronautics and Space Administration Task Load Index (NASA-TLX). Individual performance was assessed objectively based on the severity grade of errors. The relationship between the WL and performance was assessed via ordinal logistic regression. There was an increased rate of severity grade of errors with increasing WL (P value = .02). As the majority of the higher NASA-TLX scores, and the majority of the performance errors were in the residents, our findings are likely most pertinent to radiation oncology centers with training programs. WL levels may be an important factor contributing to errors during radiation therapy planning tasks. Published by Elsevier Inc.
Johns, Neil; Stretch, Cynthia; Tan, Benjamin H L; Solheim, Tora S; Sørhaug, Sveinung; Stephens, Nathan A; Gioulbasanis, Ioannis; Skipworth, Richard J E; Deans, D A Christopher; Vigano, Antonio; Ross, James A; Bathe, Oliver F; Tremblay, Michel L; Kaasa, Stein; Strasser, Florian; Gagnon, Bruno; Baracos, Vickie E; Damaraju, Sambasivarao; Fearon, Kenneth C H
2017-02-01
Cachexia affects the majority with advanced cancer. Based on current demographic and clinical factors, it is not possible to predict who will develop cachexia or not. Such variation may, in part, be due to genotype. It has recently been proposed to extend the diagnostic criteria for cachexia to include a direct measure of low skeletal muscle index (LSMI) in addition to weight loss (WL). We aimed to explore our panel of candidate single nucleotide polymorphism (SNPs) for association with WL +/- computerized tomography-defined LSMI. We also explored whether the transcription in muscle of identified genes was altered according to such cachexia phenotype METHODS: A retrospective cohort study design was used. Analysis explored associations of candidate SNPs with WL (n = 1276) and WL + LSMI (n = 943). Human muscle transcriptome (n = 134) was analysed using an Agilent platform. Single nucleotide polymorphisms in the following genes showed association with WL alone: GCKR, LEPR, SELP, ACVR2B, TLR4, FOXO3, IGF1, CPN1, APOE, FOXO1, and GHRL. SNPs in LEPR, ACVR2B, TNF, and ACE were associated with concurrent WL + LSMI. There was concordance between muscle-specific expression for ACVR2B, FOXO1 and 3, LEPR, GCKR, and TLR4 genes and LSMI and/or WL (P < 0.05). The rs1799964 in the TNF gene and rs4291 in the ACE gene are new associations when the definition of cachexia is based on a combination of WL and LSMI. These findings focus attention on pro-inflammatory cytokines and the renin-angiotensin system as biomarkers/mediators of muscle wasting in cachexia. © 2016 The Authors. Journal of Cachexia, Sarcopenia and Muscle published by John Wiley & Sons Ltd on behalf of the Society on Sarcopenia, Cachexia and Wasting Disorders.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Wilcox, Brian; Mellor, Russ; Michaluk, Craig
2013-07-01
Whiteshell Laboratories (WL) is a nuclear research site in Canada that was commissioned in 1964 by Atomic Energy of Canada Limited. It covers a total area of approximately 4,375 hectares (10,800 acres) and includes the main campus site, the Waste Management Area (WMA) and outer areas of land identified as not used for or impacted by nuclear development or operations. The WL site employed up to 1100 staff. Site activities included the successful operation of a 60 MW organic liquid-cooled research reactor from 1965 to 1985, and various research programs including reactor safety research, small reactor development, fuel development, biophysicsmore » and radiation applications, as well as work under the Canadian Nuclear Fuel Waste Management Program. In 1997, AECL made a business decision to discontinue research programs and operations at WL, and obtained government concurrence in 1998. The Nuclear Legacy Liabilities Program (NLLP) was established in 2006 by the Canadian Government to remediate nuclear legacy liabilities in a safe and cost effective manner, including the WL site. The NLLP is being implemented by AECL under the governance of a Natural Resources Canada (NRCan)/AECL Joint Oversight Committee (JOC). Significant progress has since been made, and the WL site currently holds the only Canadian Nuclear Safety Commission (CNSC) nuclear research site decommissioning license in Canada. The current decommissioning license is in place until the end of 2018. The present schedule planned for main campus decommissioning is 30 years (to 2037), followed by institutional control of the WMA until a National plan is implemented for the long-term management of nuclear waste. There is an impetus to advance work and complete decommissioning sooner. To accomplish this, AECL has added significant resources, reorganized and moved to a projectized environment. This presentation outlines changes made to the organization, the tools implemented to foster projectization, and the benefits and positive impacts on schedule and delivery. A revised organizational structure was implemented in two phases, starting 2011 April 1, to align WL staff with the common goal of decommissioning the site through the direction of the WL Decommissioning Project General Manager. On 2011 September 1, the second phase of the reorganization was implemented and WL Decommissioning staff was organized under five Divisions: Programs and Regulatory Compliance, General Site Services, Decommissioning Strategic Planning, Nuclear Facilities and Project Delivery. A new Mission, Vision and Objectives were developed for the project, and several productivity enhancements are being implemented. These include the use of an integrated and fully re-sourced Site Wide Schedule that is updated and reviewed at Plan-of-the-Week meetings, improved work distribution throughout the year, eliminating scheduling 'push' mentality, project scoreboards, work planning implementation, lean practices and various process improvement initiatives. A revised Strategic Plan is under development that reflects the improved project delivery capabilities. As a result of these initiatives, and a culture change towards a projectized approach, the decommissioning schedule will be advanced by approximately 10 years. (authors)« less
McFarlane, Laura; Altringham, John D.; Askew, Graham N.
2016-01-01
ABSTRACT Diurnal and seasonal increases in body mass and seasonal reductions in wing area may compromise a bird's ability to escape, as less of the power available from the flight muscles can be used to accelerate and elevate the animal's centre of mass. Here, we investigated the effects of intra-specific variation in wing morphology on escape take-off performance in blue tits (Cyanistes caeruleus). Flights were recorded using synchronised high-speed video cameras and take-off performance was quantified as the sum of the rates of change of the kinetic and potential energies of the centre of mass. Individuals with a lower wing loading, WL (WL=body weight/wing area) had higher escape take-off performance, consistent with the increase in lift production expected from relatively larger wings. Unexpectedly, it was found that the total power available from the flight muscles (estimated using an aerodynamic analysis) was inversely related to WL. This could simply be because birds with a higher WL have relatively smaller flight muscles. Alternatively or additionally, variation in the aerodynamic load on the wing resulting from differences in wing morphology will affect the mechanical performance of the flight muscles via effects on the muscle's length trajectory. Consistent with this hypothesis is the observation that wing beat frequency and relative downstroke duration increase with decreasing WL; both are factors that are expected to increase muscle power output. Understanding how wing morphology influences take-off performance gives insight into the potential risks associated with feather loss and seasonal and diurnal fluctuations in body mass. PMID:26994175
Fatigue Crack Initiation Mechanics of Metal Aircraft Structures
1988-08-01
Thresholds) (Ref. 6) and are included as Appendix A. In summary, two flow stresses were identified. Microplastic flow takes place in all grains at fully...R.O. Ritchie and E.A. Starke, EMAS, 93-101 (1987). 7. M.R. James and W.L. Morris, "Load Sequence Effects on the Deformation of Isolated Microplastic ...417 (1980). 17. M.R. James and W.L. Morris, "The Effect of Microplastic Surface Deformation on the Growth of Small Cracks," Small Fatigue Cracks, R.O
DOE Office of Scientific and Technical Information (OSTI.GOV)
Wilcox, Brian; May, Doug; Howlett, Don
2013-07-01
Whiteshell Laboratories (WL) is a nuclear research establishment owned by the Canadian government and operated by Atomic Energy of Canada Limited (AECL) since the early 1960's. WL is currently under a decommissioning license and the mandate is to remediate the nuclear legacy liabilities in a safe and cost effective manner. The WL Project is the first major nuclear decommissioning project in Canada. A major initiative underway is to decommission and demolish the main R and D Laboratory complex. The Building 300 R and D complex was constructed to accommodate laboratories and offices which were mainly used for research and developmentmore » associated with organic-cooled reactors, nuclear fuel waste management, reactor safety, advanced fuel cycles and other applications of nuclear energy. Building 300 is a three storey structure of approximately 16,000 m{sup 2}. In order to proceed with building demolition, the contaminated systems inside the building have to be characterized, removed, and the waste managed. There is a significant focus on volume reduction of radioactive waste for the WL project. The active ventilation system is one of the significant contaminated systems in Building 300 that requires decommissioning and removal. The active ventilation system was designed to manage hazardous fumes and radioactivity from ventilation devices (e.g., fume hoods, snorkels and glove boxes) and to prevent the escape of airborne hazardous material outside of the laboratory boundary in the event of an upset condition. The system includes over 200 ventilation devices and 32 active exhaust fan units and high efficiency particulate air (HEPA) filters. The strategy to remove the ventilation system was to work from the laboratory end back to the fan/filter system. Each ventilation duct was radiologically characterized. Fogging was used to minimize loose contamination. Sections of the duct were removed by various cutting methods and bagged for temporary storage prior to disposition. Maintenance of building heating, ventilation and air conditioning (HVAC) balancing was critical to ensure proper airflow and worker safety. Approximately 103 m{sup 3} of equipment and materials were recovered or generated by the project. Low level waste accounted for approximately 37.4 m{sup 3}. Where possible, ducting was free released for metal recycling. Contaminated ducts were compacted into B-1000 containers and stored in a Shielded Modular Above-Ground Storage Facility (SMAGS) on the WL site awaiting final disposition. The project is divided into three significant phases, with Phases 1 and 2 completed. Lessons learned during the execution of Phases 1 and 2 have been incorporated into the current ventilation removal. (authors)« less
Zheng, Chunfang; Jiang, Dong; Liu, Fulai; Dai, Tingbo; Jing, Qi; Cao, Weixing
2009-04-01
The objective of this study was to investigate the effects of salt (ST) and waterlogging (WL) stresses and their combination (SW) on leaf photosynthesis, chloroplast ATP synthesis, and antioxidant capacity in wheat (Triticum aestivum L.). Two winter wheat cultivars, Huaimai 17 and Yangmai 12, differing in their tolerance to ST and WL stresses were used. The plants were grown in pots and were subjected to ST, WL, and SW from 7 days after anthesis (DAA). The WL and SW treatments lasted for 5 days, while the ST treatment was continuously imposed during the grain filling stage. Significant decrease in net photosynthetic rate (PN) of the flag leaf was observed under the ST and SW treatments from 10 DAA in Yangmai 12 and at 18 DAA in both cultivars, which could be stomatal closure related. At 18 DAA, clear reduction in PN under the ST and SW treatments was observed, which was associated with chlorosis, damages to the photosystem II (PSII), enhanced lipid peroxidation, and depressed ATP synthesis in the chloroplasts of the flag leaf. Whereas, WL treatment alone had slightly negative effect on PN, which was mainly attributed to leaf chlorosis and waste in harvested energy by the PSII reaction center dispersed via non-photochemical approaches. Copyright © 2009 Elsevier Ireland Ltd. All rights reserved.
Rhizosphere of Avicennia marina (Forsk.) Vierh. as a landmark for polythene degrading bacteria.
Shahnawaz, Mohd; Sangale, Manisha K; Ade, Avinash B
2016-07-01
Due to high durability, cheap cost, and ease of manufacture, 311 million tons of plastic-based products are manufactured around the globe per annum. The slow/least rate of plastic degradation leads to generation of million tons of plastic waste per annum, which is of great environmental concern. Of the total plastic waste generated, polythene shared about 64 %. Various methods are available in the literature to tackle with the plastic waste, and biodegradation is considered as the most accepted, eco-friendly, and cost-effective method of polythene waste disposal. In the present study, an attempt has been made to isolate, screen, and characterize the most efficient polythene degrading bacteria by using rhizosphere soil of Avicennia marina as a landmark. From 12 localities along the west coast of India, a total of 123 bacterial isolates were recorded. Maximum percent weight loss (% WL; 21.87 ± 6.37 %) was recorded with VASB14 at pH 3.5 after 2 months of shaking at room temperature. Maximum percent weight gain (13.87 ± 3.6 %) was reported with MANGB5 at pH 7. Maximum percent loss in tensile strength (% loss in TS; 87.50 ± 4.8 %) was documented with VASB1 at pH 9.5. The results based on the % loss in TS were only reproducible. Further, the level of degradation was confirmed by scanning electron microscopic (SEM) and Fourier transform infrared spectroscopy (FTIR) analysis. In SEM analysis, scions/crakes were found on the surface of the degraded polythene, and mass of bacterial cell was also recorded on the weight-gained polythene strips. Maximum reduction in carbonyl index (4.14 %) was recorded in untreated polythene strip with Lysinibacillus fusiformis strain VASB14/WL. Based on 16S ribosomal RNA (rRNA) gene sequence homology, the most efficient polythene degrading bacteria were identified as L. fusiformis strainVASB14/WL and Bacillus cereus strain VASB1/TS.
Split-Ring Resonator Loaded Miniaturised Slot for the Slotted Waveguide Antenna Stiffened Structure
2011-03-01
explains the material analysis of BST varactors using the new sputterer so the varactors can be fabricated at RMIT university and utilised for the SRR...44-0093 (*) - Barium Strontium Titanium Oxide - Ba0.77Sr0.23TiO3 - Y: 0.10 % - d x by: 1. - WL: 1.5406 - Tetragonal - Operations: Import D:\\Sensors...unknown unknown BST on sapphire - 2 44-0093 (*) - Barium Strontium Titanium Oxide - Ba0.77Sr0.23TiO3 - Y: 0.10 % - d x by: 1. - WL: 1.5406 - 0
Johns, Neil; Stretch, Cynthia; Tan, Benjamin H.L.; Solheim, Tora S.; Sørhaug, Sveinung; Stephens, Nathan A.; Gioulbasanis, Ioannis; Skipworth, Richard J.E.; Deans, D.A. Christopher; Vigano, Antonio; Ross, James A.; Bathe, Oliver F.; Tremblay, Michel L.; Kaasa, Stein; Strasser, Florian; Gagnon, Bruno; Baracos, Vickie E.; Damaraju, Sambasivarao
2016-01-01
Background Cachexia affects the majority with advanced cancer. Based on current demographic and clinical factors, it is not possible to predict who will develop cachexia or not. Such variation may, in part, be due to genotype. It has recently been proposed to extend the diagnostic criteria for cachexia to include a direct measure of low skeletal muscle index (LSMI) in addition to weight loss (WL). We aimed to explore our panel of candidate single nucleotide polymorphism (SNPs) for association with WL +/− computerized tomography‐defined LSMI. We also explored whether the transcription in muscle of identified genes was altered according to such cachexia phenotype Methods A retrospective cohort study design was used. Analysis explored associations of candidate SNPs with WL (n = 1276) and WL + LSMI (n = 943). Human muscle transcriptome (n = 134) was analysed using an Agilent platform. Results Single nucleotide polymorphisms in the following genes showed association with WL alone: GCKR, LEPR, SELP, ACVR2B, TLR4, FOXO3, IGF1, CPN1, APOE, FOXO1, and GHRL. SNPs in LEPR, ACVR2B, TNF, and ACE were associated with concurrent WL + LSMI. There was concordance between muscle‐specific expression for ACVR2B, FOXO1 and 3, LEPR, GCKR, and TLR4 genes and LSMI and/or WL (P < 0.05). Conclusions The rs1799964 in the TNF gene and rs4291 in the ACE gene are new associations when the definition of cachexia is based on a combination of WL and LSMI. These findings focus attention on pro‐inflammatory cytokines and the renin–angiotensin system as biomarkers/mediators of muscle wasting in cachexia. PMID:27897403
NASA Astrophysics Data System (ADS)
Kooh, Muhammad Raziq Rahimi; Dahri, Muhammad Khairud; Lim, Linda B. L.; Lim, Lee Hoon; Chan, Chin Mei
2018-05-01
Three plant-based materials, namely water lettuce (WL), tarap peel (TP) and cempedak peel (CP), were used to investigate their potentials as adsorbents using acid blue 25 (AB25) dye as a model for acidic dye. The adsorbents were characterised using Fourier transform infrared spectroscopy, X-ray fluorescence and scanning electron microscope. Batch experiments involving parameters such as pH, temperature, contact time, and initial dye concentration were done to investigate the optimal conditions for the adsorption of AB25 onto the adsorbents. Thermodynamics study showed that the uptake of AB25 by the three adsorbents was feasible and endothermic in nature. Both the Langmuir and Freundlich isotherm models can be used to describe the adsorption process of AB25 onto WL and CP while pseudo-second-order fitted the kinetics data, suggesting that chemisorptions were majorly involved. The use of 0.1 M of NaOH showed the best results in regenerating of the WL, TP and CP's adsorption ability after AB25 treatment.
Polidori, Carlo; Nieves-Aldrey, José Luis
2015-02-01
Since its introduction in Chile, the European Bombus terrestris L. (Hymenoptera: Apidae) has progressively reduced the abundance of the native Patagonian bumblebee, Bombus dahlbomii Guérin. Because an important cause of successful invasion of a species may depend on a potentially advantageous phenotype, we studied morphologies related to flight performance (flight muscle ratio (FMR), wing loading (WL), excess power index (EPI, which integrates FMR and WL) and wing aspect ratio (AR)) in the queens of the two species. Previous empirical studies showed that greater FMR, AR and EPI, and lower WL increase flight performance. In the Patagonian Chilean fjord where the study was carried out, B. dahlbomii was 40% heavier than B. terrestris, a difference theoretically allowing the queens of the native species to take off with heavier loads, despite the fact that the two species have virtually identical FMRs. However, FMR negatively depended on body mass at the intra-specific level. The total wing area was 35% greater in B. dahlbomii, but the difference in forewing length was only of 16%. Once taken into account the effect of body size, WL, was significantly lower in B. terrestris. AR increased with body mass and did not differ between species. EPI was weakly but significantly higher in B. terrestris. Experiments formally linking such parameters with flight performance may help to explain the observed quick and wide spread of this alien species in Patagonia in the last few years. Copyright © 2014 Académie des sciences. Published by Elsevier SAS. All rights reserved.
Falling Victim to Wasps in the Air: A Fate Driven by Prey Flight Morphology?
Ballesteros, Yolanda; Polidori, Carlo; Tormos, José; Baños-Picón, Laura; Asís, Josep D.
2016-01-01
In prey-predator systems where the interacting individuals are both fliers, the flight performance of both participants heavily influences the probability of success of the predator (the prey is captured) and of the prey (the predator is avoided). While the flight morphology (an estimate of flight performance) of predatory wasps has rarely been addressed as a factor that may contribute to explain prey use, how the flight morphology of potential prey influences the output of predator-prey encounters has not been studied. Here, we hypothesized that flight morphology associated with flight ability (flight muscle mass to body mass ratio (FMR) and body mass to wing area ratio (wing loading, WL)) of Diptera affect their probability of being captured by specialized Diptera-hunting wasps (Bembix merceti and B. zonata), predicting a better manoeuvrability and acceleration capacity achieved by higher FMR and lower WL, and flight speed achieved by higher WL. In addition, wasp species with better flight morphology should be less limited by an advantageous Diptera flight morphology. Overall, the abundance of dipterans in the environment explained an important part of the observed variance in prey capture rate. However, it was not the only factor shaping prey capture. First, higher prey abundance was associated with greater capture rate for one species (B. merceti), although not for the other one. Second, the interaction observed between the environmental dipteran availability and dipteran WL for B. zonata suggests that greater dipteran WL (this probably meaning high cruising speed) decreased the probability of being captured, as long as fly abundance was high in the environment. Third, greater dipteran FMR (which likely means high manoeuvrability and acceleration capacity) helped to reduce predation by B. merceti if, again, dipterans were abundant in the environment. Wasp WL only varied with body mass but not between species, thereby hardly accounting for inter-specific differences in the wasps’ predatory patterns. However, the greater FMR of B. zonata, which implies better flight performance and greater load-lifting capacity, may explain why the capture rate in the two wasp species is affected by different factor interactions. In conclusion, although prey availability remains the primary factor shaping prey use, prey flight morphology seems to gain an additional role under conditions of abundant prey, when wasps can avoid flies with better flight ability. PMID:27046238
Isolating active orogenic wedge deformation in the southern Subandes of Bolivia
NASA Astrophysics Data System (ADS)
Weiss, Jonathan R.; Brooks, Benjamin A.; Foster, James H.; Bevis, Michael; Echalar, Arturo; Caccamise, Dana; Heck, Jacob; Kendrick, Eric; Ahlgren, Kevin; Raleigh, David; Smalley, Robert; Vergani, Gustavo
2016-08-01
A new GPS-derived surface velocity field for the central Andean backarc permits an assessment of orogenic wedge deformation across the southern Subandes of Bolivia, where recent studies suggest that great earthquakes (>Mw 8) are possible. We find that the backarc is not isolated from the main plate boundary seismic cycle. Rather, signals from subduction zone earthquakes contaminate the velocity field at distances greater than 800 km from the Chile trench. Two new wedge-crossing velocity profiles, corrected for seasonal and earthquake affects, reveal distinct regions that reflect (1) locking of the main plate boundary across the high Andes, (2) the location of and loading rate at the back of orogenic wedge, and (3) an east flank velocity gradient indicative of décollement locking beneath the Subandes. Modeling of the Subandean portions of the profiles indicates along-strike variations in the décollement locked width (WL) and wedge loading rate; the northern wedge décollement has a WL of ~100 km while accumulating slip at a rate of ~14 mm/yr, whereas the southern wedge has a WL of ~61 km and a slip rate of ~7 mm/yr. When compared to Quaternary estimates of geologic shortening and evidence for Holocene internal wedge deformation, the new GPS-derived wedge loading rates may indicate that the southern wedge is experiencing a phase of thickening via reactivation of preexisting internal structures. In contrast, we suspect that the northern wedge is undergoing an accretion or widening phase primarily via slip on relatively young thrust-front faults.
Maldonado, Maria; Molfese, David L; Viswanath, Humsini; Curtis, Kaylah; Jones, Ashley; Hayes, Teresa G; Marcelli, Marco; Mediwala, Sanjay; Baldwin, Philip; Garcia, Jose M; Salas, Ramiro
2018-06-01
Little is known about the brain mechanisms underlying cancer-associated weight loss (C-WL) in humans despite this condition negatively affecting their quality of life and survival. We tested the hypothesis that patients with C-WL have abnormal connectivity in homeostatic and hedonic brain pathways together with altered brain activity during food reward. In 12 patients with cancer and 12 healthy controls, resting-state functional connectivity (RSFC, resting brain activity observed through changes in blood flow in the brain which creates a blood oxygen level-dependent signal that can be measured using functional magnetic resonance imaging) was used to compare three brain regions hypothesized to play a role in C-WL: the hypothalamus (homeostatic), the nucleus accumbens (hedonic), and the habenula (an important regulator of reward). In addition, the brain reward response to juice was studied. Participants included 12 patients with histological diagnosis of incurable cancer (solid tumours), a European Cooperative Oncology Group performance status of 0-2, and a ≥5% involuntary body weight loss from pre-illness over the previous 6 months and 12 non-cancer controls matched for age, sex, and race. RSFC between the hypothalamus, nucleus accumbens, and habenula and brain striatum activity as measured by functional MRI during juice reward delivery events were the main outcome measures. After adjusting for BMI and compared with matched controls, patients with C-WL were found to have reduced RSFC between the habenula and hypothalamus (P = 0.04) and between the habenula and nucleus accumbens (P = 0.014). Patients with C-WL also had reduced juice reward responses in the striatum compared with controls. In patients with C-WL, reduced connectivity between both homeostatic and hedonic brain regions and the habenula and reduced juice reward were observed. Further research is needed to establish the relevance of the habenula and striatum in C-WL. Published 2018. This article is a U.S. Government work and is in the public domain in the USA. Journal of Cachexia, Sarcopenia and Muscle published by John Wiley & Sons Ltd on behalf of the Society on Sarcopenia, Cachexia and Wasting Disorders.
Jiang, Jianguo; Gong, Changxiu; Wang, Jiaming; Tian, Sicong; Zhang, Yujing
2014-03-01
This paper describes a series of studies on the effects of food waste disintegration using an ultrasonic generator and the production of volatile fatty acids (VFAs) by anaerobic hydrolysis. The results suggest that ultrasound treatment can significantly increase COD [chemical oxygen demand], proteins and reducing sugars, but decrease that of lipids in food waste supernatant. Ultrasound pre-treatment boosted the production of VFAs dramatically during the fermentation of food waste. At an ultrasonic energy density of 480W/L, we treated two kinds of food waste (total solids (TS): 40 and 100g/L, respectively) with ultrasound for 15min. The amount of COD dissolved from the waste increased by 1.6-1.7-fold, proteins increased by 3.8-4.3-fold, and reducing sugars increased by 4.4-3.6-fold, whereas the lipid content decreased from 2 to 0.1g/L. Additionally, a higher VFA yield was observed following ultrasonic pre-treatment. Copyright © 2013 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Yang, Di
Duplex stainless steel (DSS) is a dual-phase material with approximately equal volume amount of austenite and ferrite. It has both great mechanical properties (good ductility and high tensile/fatigue strength) and excellent corrosion resistance due to the mixture of the two phases. Cyclic loadings with high stress level and low frequency are experienced by many structures. However, the existing study on corrosion fatigue (CF) study of various metallic materials has mainly concentrated on relatively high frequency range. No systematic study has been done to understand the ultra-low frequency (˜10-5 Hz) cyclic loading effect on stress corrosion cracking (SCC) of DSSs. In this study, the ultra-low frequency cyclic loading effect on SCC of DSS 2205 was studied in acidified sodium chloride and caustic white liquor (WL) solutions. The research work focused on the environmental effect on SCC of DSS 2205, the cyclic stress effect on strain accumulation behavior of DSS 2205, and the combined environmental and cyclic stress effect on the stress corrosion crack initiation of DSS 2205 in the above environments. Potentiodynamic polarization tests were performed to investigate the electrochemical behavior of DSS 2205 in acidic NaCl solution. Series of slow strain rate tests (SSRTs) at different applied potential values were conducted to reveal the optimum applied potential value for SCC to happen. Room temperature static and cyclic creep tests were performed in air to illustrate the strain accumulation effect of cyclic stresses. Test results showed that cyclic loading could enhance strain accumulation in DSS 2205 compared to static loading. Moreover, the strain accumulation behavior of DSS 2205 was found to be controlled by the two phases of DSS 2205 with different crystal structures. The B.C.C. ferrite phase enhanced strain accumulation due to extensive cross-slips of the dislocations, whereas the F.C.C. austenite phase resisted strain accumulation due to cyclic strain hardening. Cyclic SSRTs were performed under the conditions that SCC occurs in sodium chloride and WL solutions. Test results show that cyclic stress facilitated crack initiations in DSS 2205. Stress corrosion cracks initiated from the intermetallic precipitates in acidic chloride environment, and the cracks initiated from austenite phase in WL environment. Cold-working has been found to retard the crack initiations induced by cyclic stresses.
Zelleke, G; Moudgal, R P; Asmare, A
2005-02-01
(1) Four breeding groups of Rhode Island Red and White Leghorn domestic fowl (RIR (female) x RIR (male), RIR (female) x WL (male), WL (female) x RIR (male) and WL (female) x WL (male)) were compared for fertility, hatchability, and their post-insemination sustainability, egg weight loss during incubation and uncovered yolk in abdominal cavity of dead in shell in order to understand the problems associated with the RIR breed in these respects. (2) Crossing RIR (female) with WL (male) or in reverse sex combinations did not improve fertility in comparison to pure RIR chickens and all these groups were less fertile than the pure WL. (3) Unlike fertility, hatchability in RIR improved with the change to either sex partner of the WL breed but the WL (female) x RIR (male) combination was similar to the pure WL (97.72 and 97.12%, respectively). In contrast, crossing RIR (female) with WL (male) resulted in an improvement (86.67%) as compared to pure RIR (76.67%) but still lower than the pure WL and WL (female) x RIR (male) cross. (4) Egg weight loss during incubation was more (20.16%) in pure RIR as compared to RIR (female) x WL (male) (17.13%), followed by WL (female) x RIR (male) (10.28%) and pure WL (9.57%). (5) There were more dead-in-shell embryos with yolks outside their abdominal cavity in pure RIR and their crosses as compared to pure WL breeds. (6) Fertility was sustained for longer in WL than other combinations with post-artificial insemination using constant number of spermatozoa. Fertility after a week of insemination tended to decrease more rapidly than hatchability on a fertile egg basis. (7) It is concluded that both sexes are responsible for the poor fertility in RIR but the female is responsible for poor hatchability and this poor performance is mainly due to greater egg weight loss during incubation.
Gabriel, Emmanuel; Singla, Smit; Kim, Minhyung; Fisher, Daniel; Powers, Colin; Visioni, Anthony; Attwood, Kristopher; Skitzki, Joseph
2017-09-01
Water lavage (WL) during gastrointestinal cancer surgery has osmotically mediated lytic effects on tumor cells. We investigated the safety and efficacy of WL with CRS-HIPEC. This is a retrospective review, 1/2003-7/2014, of a single institution experience with CRS-HIPEC comparing patients who had WL (WL+) to those who did not (WL-). Of 157 CRS-HIPECs, 16 (10.2%) were WL+. WL+ had more PCI scores >20 compared to WL- (56.3% vs 19.4%, respectively, p = 0.003); however, the completeness of cytoreduction (CC) was similar. There were no differences in hospital length of stay or post-operative complications. The average POD 1 sodium (Na) level was statistically lower in the WL+ group (133.6 ± 2.5 vs 135.5 ± 3.2 mEq/L, p = 0.023); however, the average Na at discharge for each group was 140 mEq/L. There were no differences in 3-year OS (3WL+:0.63 vs WL-:0.68, p = 0.97) or RFS (WL+:0.32 vs WL-:0.39, p = 0.47). A subset analysis for patients with PCI >20 showed no difference between groups. WL offers a low cost, safe and theoretically efficacious method of tumor cell lysis for peritoneal malignancy. Copyright © 2017 Elsevier Inc. All rights reserved.
Unick, Jessica L; Neiberg, Rebecca H; Hogan, Patricia E; Cheskin, Lawrence J; Dutton, Gareth R; Jeffery, Robert; Nelson, Julie A; Pi-Sunyer, Xavier; West, Delia Smith; Wing, Rena R
2015-07-01
Examine the relationship between 1- and 2-month weight loss (WL) and 8-year WL among participants enrolled in a lifestyle intervention. 2,290 Look AHEAD participants (BMI: 35.65 ± 5.93 kg/m(2) ) with type 2 diabetes received an intensive behavioral WL intervention. 1- and 2-month WL were associated with yearly WL through Year 8 (P's < 0.0001). At Month 1, participants losing 2-4% and >4% had 1.62 (95% CI: 1.32, 1.98) and 2.79 (95% CI: 2.21, 3.52) times higher odds of achieving ≥5% WL at Year 4 and 1.28 (95% CI: 1.05,1.58) and 1.77 (95% CI: 1.40, 2.24) times higher odds of achieving ≥5% WL at Year 8, compared to those losing <2% initially. At Month 2, 3-6% WL resulted in greater odds of achieving ≥5% WL at Year 4 (OR = 1.85; CI: 1.48, 2.32), and >6% WL resulted in the greatest odds of achieving ≥5% WL at Year 4 (OR = 3.85; CI: 3.05, 4.88) and Year 8 (OR = 2.28; CI: 1.81, 2.89), compared to those losing <3%. Differences in adherence between WL categories were observed as early as Month 2. 1- and 2-month WL was associated with 8-year WL. Future studies should examine whether alternative treatment strategies can be employed to improve treatment outcomes among those with low initial WL. © 2015 The Obesity Society.
Rastogi, Amit; Early, Dayna S; Gupta, Neil; Bansal, Ajay; Singh, Vikas; Ansstas, Michael; Jonnalagadda, Sreenivasa S; Hovis, Christine E; Gaddam, Srinivas; Wani, Sachin B; Edmundowicz, Steven A; Sharma, Prateek
2011-09-01
Missing adenomas and the inability to accurately differentiate between polyp histology remain the main limitations of standard-definition white-light (SD-WL) colonoscopy. To compare the adenoma detection rates of SD-WL with those of high-definition white-light (HD-WL) and narrow-band imaging (NBI) as well as the accuracy of predicting polyp histology. Multicenter, prospective, randomized, controlled trial. Two academic medical centers in the United States. Subjects undergoing screening or surveillance colonoscopy. Subjects were randomized to undergo colonoscopy with one of the following: SD-WL, HD-WL, or NBI. The proportion of subjects detected with adenomas, adenomas detected per subject, and the accuracy of predicting polyp histology real time. A total of 630 subjects were included. The proportion of subjects with adenomas was 38.6% with SD-WL compared with 45.7% with HD-WL and 46.2% with NBI (P = .17 and P = .14, respectively). Adenomas detected per subject were 0.69 with SD-WL compared with 1.12 with HD-WL and 1.13 with NBI (P = .016 and P = .014, respectively). HD-WL and NBI detected more subjects with flat and right-sided adenomas compared with SD-WL (all P values <.005). NBI had a superior sensitivity (90%) and accuracy (82%) to predict adenomas compared with SD-WL and HD-WL (all P values <.005). Academic medical centers with experienced endoscopists. There was no difference in the proportion of subjects with adenomas detected with SD-WL, HD-WL, and NBI. However, HD-WL and NBI detected significantly more adenomas per subject (>60%) compared with SD-WL. NBI had the highest accuracy in predicting adenomas in real time during colonoscopy. ( NCT 00614770.). Copyright © 2011 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.
Radiological Monitoring of Waste Treatment Plant
DOE Office of Scientific and Technical Information (OSTI.GOV)
Amin, Y. M.; Nik, H. W.
2011-03-30
Scheduled waste in West Malaysia is handled by Concession Company and is stored and then is incinerated. It is known that incineration process may result in naturally occurring radioactive materials (NORM) to be concentrated. In this study we have measured three samples consist of by-product from the operation process such as slag, filter cake and fly ash. Other various environmental media such as air, surface water, groundwater and soil within and around the plant have also been analysed for their radioactivity levels. The concentration of Ra-226, Ac-228 and K-40 in slag are 0.062 Bq/g, 0.016 Bq/g and 0.19 Bq/g respectively.more » The total activity (Ra{sub eq}) in slag is 99.5 Bq/kg. The concentration in fly ash is 0.032 Bq/g, 0.16 Bq/g and 0.34 Bq/g for Ra-226, Ac-228 and K-40 respectively resulting in Raeq of 287.0 Bq/kg. For filter cake, the concentration is 0.13 Bq/g, 0.031 Bq/g and 0.33 Bq/g for Ra-226, Ac-228 and K-40 respectively resulting in Raeq of 199.7 Bq/kg. The external radiation level ranges from 0.08 {mu}Sv/h (Administrative building) to 0.35 {mu}Sv/h (TENORM storage area). The concentration level of radon and thoron progeny varies from 0.0001 to 0.0016 WL and 0.0006 WL to 0.002 WL respectively. For soil samples, the activity ranges from 0.11 Bq/g to 0.29 Bq/g, 0.06 Bq/g to 0.18 Bq/g and 0.065 Bq/g to 0.38 Bq/g for Ra-226, Ac-228 and K-40 respectively. While activity in water, except for a trace of K-40, it is non-detectable.« less
Todorov, Dimitar; Zderic, Ivan; Richards, R Geoff; Lenz, Mark; Knobe, Matthias; Enchev, Dian; Baltov, Asen; Gueorguiev, Boyko; Stoffel, Karl
2018-05-10
Treatment of complex osteoporotic distal femur fractures with the Less Invasive Stabilization System (LISS) has been associated with high complication rates. The aim of this study was to investigate the biomechanical competence of two different techniques of augmented versus conventional LISS plating. Unstable distal femoral fracture AO/OTA 33-A3 was created via osteotomies in artificial femora simulating osteoporotic bone. Three study groups, consisting of 10 specimens each, were created for instrumentation with either LISS plate, LISS plate with additional polylactide intramedullary graft, or LISS plate plus medial locking plate (double plating). All specimens were non-destructively tested under axial (20-150N) and torsional (0-4Nm) quasi-static loading. Each construct was tested with two different working length (WL) configurations (long and short) of the LISS plate. Relative movements between the most medial superior and inferior osteotomy aspects were investigated via three-dimensional motion tracking analysis. Double plating revealed significantly smaller longitudinal and shear displacement than the other two techniques (P≤0.001). In addition, LISS plus graft fixation was with significantly less longitudinal displacement in comparison to conventional LISS plating (P < 0.001). Long WL resulted in significantly higher longitudinal and shear displacement compared to short WL for LISS and LISS plus graft (P≤0.032), but not for double plating (P > 0.999). In conclusion, intramedullary grafting resulted in significantly increased fracture stability under axial loading in comparison to conventional LISS plating. Although it was not efficient enough to provide comparable stability to double plating, intramedullary grafting may be considered as a useful biological alternative to the latter in a surgeon's armamentarium. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.
Ryan, Alice S
2016-05-01
To determine whether a hypocaloric diet alone (WL) or with exercise training (AEX + WL) is effective in improving body composition, fitness, glucose utilization and CVD risk factors in sedentary women with a history of gestational diabetes (GDM) and with type 2 diabetes (T2DM). Longitudinal clinical investigation of 25 overweight/obese (BMI: 32 ± 1 kg/m(2)) women (59 ± 1 yrs) with a GDM history (n = 20) or T2DM (n = 5). Women completed 6 months WL (n = 10) or AEX+WL (n = 15) with VO2max, body composition, and glucose tolerance testing. Insulin sensitivity was measured during the last 30 min of 2 h hyperinsulinemic-euglycemic clamps (40 mU·m(-2.)min(-1)) before and after interventions. Body weight decreased ~7% after WL and AEX+WL (p < 0.001), with an 11-12% decrease in fat mass (p < 0.0001). Visceral fat and subcutaneous abdominal fat decreased 27 and 10% after WL (p < 0.01) and 14 and 11% after AEX + WL (p < 0.05). VO2max increased 16% after AEX + WL (p < 0.001) and did not change after WL. Glucose AUC decreased 14 and 13% after WL (p < 0.05) and AEX + WL (p < 0.01) with a 42% decrease in insulin AUC after AEX + WL (p < 0.01). Glucose utilization increased 25% (p = 0.05) with AEX + WL and 7% with WL. A six-month aerobic exercise program combined with moderate weight loss reduces body weight, visceral and subcutaneous abdominal fat, and improves insulin sensitivity in older women who had previously been diagnosed with GDM and those with T2DM. These findings should encourage women with a history of GDM to engage in an active lifestyle and reduce caloric intake to lower the risk for the development of T2DM.
Ryan, Alice S.
2016-01-01
Purpose To determine whether a hypocaloric diet alone (WL) or with exercise training (AEX+WL) is effective in improving body composition, fitness, glucose utilization and CVD risk factors in sedentary women with a history of gestational diabetes (GDM) and with type 2 diabetes (T2DM). Materials and Methods Longitudinal clinical investigation of 25 overweight/obese (BMI:32±1 kg/m2) women (59±1 yrs) with a GDM history (n=20) or T2DM (n=5). Women completed 6 months WL (n=10) or AEX+WL (n=15) with VO2max, body composition, and glucose tolerance testing. Insulin sensitivity was measured during the last 30 min of 2-hour hyperinsulinemic-euglycemic clamps (40 mU·m−2·min−1) before and after interventions. Results Body weight decreased ~7% after WL and AEX+WL (P<0.001), with an 11–12% decrease in fat mass (P<0.0001). Visceral fat and subcutaneous abdominal fat decreased 27 and 10% after WL (P<0.01) and 14 and 11% after AEX+WL (P<0.05). VO2max increased 16% after AEX+WL (P<0.001) and did not change after WL. Glucose AUC decreased 14 and 13% after WL (P<0.05) and AEX+WL (P<0.01) with a 42% decrease in insulin AUC after AEX+WL (P<0.01). Glucose utilization increased 25% (P=0.05) with AEX+WL and 7% with WL. Conclusions A six-month aerobic exercise program combined with moderate weight loss reduces body weight, visceral and subcutaneous abdominal fat, and improves insulin sensitivity in older women who had previously been diagnosed with GDM and those with T2DM. These findings should encourage women with a history of GDM to engage in an active lifestyle and reduce caloric intake to lower the risk for the development of T2DM. PMID:26925596
Ryan, Alice S.; Ge, Shealinna; Blumenthal, Jacob B.; Serra, Monica C.; Prior, Steven J.; Goldberg, Andrew P.
2014-01-01
Background/Objectives To examine the relationships of plasma and tissue markers of systemic and vascular inflammation to obesity and insulin resistance and determine the effects of aerobic exercise training+weight loss (AEX+WL) and weight loss (WL) on these biomarkers. Design Prospective controlled study. Participants Seventy-seven overweight and obese sedentary postmenopausal women. Interventions Six months, 3d/wk AEX+WL (n=37) or WL (n=40). Measurements Total body dual-energy x-ray absorptiometry, abdominal computed tomography scans, hyperinsulinemic-euglycemic clamps, adipose tissue biopsies (n=28), and blood for Homeostasis model assessment-insulin resistance, and soluble forms of intracellular adhesion molecule (sICAM-1) and vascular CAM-1 (sVCAM-1), C-reactive protein (CRP), and serum amyloid A (SAA). Results Body weight, %fat, visceral fat, triglyceride levels and systolic blood pressure decreased comparably after WL and AEX+WL (P<0.05). VO2max increased 16% after AEX+WL (P<0.001). Insulin resistance decreased in both groups (P<0.01). Glucose utilization increased 10% (P< 0.05) after AEX+WL and 8% with WL (P=0.07). AEX+WL and WL decreased CRP by 29% and 21%, (P<0.05). SAA levels decreased two-fold more after AEX+WL (−19%, P<0.05) than with WL (−9%, P=0.08). Plasma sICAM-1 and sVCAM-1 levels did not change; however, women with the greatest reduction in plasma sICAM-1 levels had the greatest reductions in fasting glucose, insulin and insulin resistance (P<0.05). Gluteal ICAM mRNA levels decreased 27% after AEX+WL (P<0.05) and did not change after WL. Conclusion Obesity and insulin resistance worsen markers of systemic and vascular inflammation. A reduction in plasma sICAM-1 is important to improve insulin sensitivity. CRP and SAA and tissue ICAM decrease with exercise and weight loss, suggesting that exercise training is a necessary component of lifestyle modification in obese postmenopausal women. PMID:24635342
Ashtary-Larky, Damoon; Ghanavati, Matin; Lamuchi-Deli, Nasrin; Payami, Seyedeh Arefeh; Alavi-Rad, Sara; Boustaninejad, Mehdi; Afrisham, Reza; Abbasnezhad, Amir; Alipour, Meysam
2017-07-01
Achieving weight loss (WL) in a short time regardless of its consequences has always been the focus of many obese and overweight people. In this study, anthropometric and metabolic effects of two diets for rapid and slow WL and their consequences were examined. Forty-two obese and overweight individuals were randomly divided to 2 groups; rapid WL (weight loss of at least 5% in 5 weeks) and slow WL (weight loss of at least 5% in 15 weeks). To compare the effects of the rate of WL in 2 groups, the same amount of was achieved with different durations. Anthropometric indices, lipid, and glycemic profiles, and systolic and diastolic blood pressures were evaluated before and after the intervention. Both protocols of rapid WL and slow WL caused reduction in waist circumference, hip circumference, total body water, body fat mass, lean body mass, and resting metabolic rate (RMR). Further reduction in waist circumference, hip circumference, fat mass, and percentage of body fat was observed in slow WL and decreased total body water, lean body mass, fat free mass, and RMR was observed in rapid WL. Improvement in lipid and glycemic profiles was observed in both groups. Reduction of low-density lipoprotein and fasting blood sugar, improvement of insulin resistance, and sensitivity were more significant in rapid WL in comparison to slow WL. Weight Loss regardless of its severity could improve anthropometric indicators, although body composition is more favorable following a slow WL. Both diets improved lipid and glycemic profiles. In this context, rapid WL was more effective. (IRCT2016010424699N2).
Ashtary-Larky, Damoon; Ghanavati, Matin; Lamuchi-Deli, Nasrin; Payami, Seyedeh Arefeh; Alavi-Rad, Sara; Boustaninejad, Mehdi; Afrisham, Reza; Abbasnezhad, Amir; Alipour, Meysam
2017-01-01
Background Achieving weight loss (WL) in a short time regardless of its consequences has always been the focus of many obese and overweight people. In this study, anthropometric and metabolic effects of two diets for rapid and slow WL and their consequences were examined. Methods Forty-two obese and overweight individuals were randomly divided to 2 groups; rapid WL (weight loss of at least 5% in 5 weeks) and slow WL (weight loss of at least 5% in 15 weeks). To compare the effects of the rate of WL in 2 groups, the same amount of was achieved with different durations. Anthropometric indices, lipid, and glycemic profiles, and systolic and diastolic blood pressures were evaluated before and after the intervention. Results Both protocols of rapid WL and slow WL caused reduction in waist circumference, hip circumference, total body water, body fat mass, lean body mass, and resting metabolic rate (RMR). Further reduction in waist circumference, hip circumference, fat mass, and percentage of body fat was observed in slow WL and decreased total body water, lean body mass, fat free mass, and RMR was observed in rapid WL. Improvement in lipid and glycemic profiles was observed in both groups. Reduction of low-density lipoprotein and fasting blood sugar, improvement of insulin resistance, and sensitivity were more significant in rapid WL in comparison to slow WL. Conclusions Weight Loss regardless of its severity could improve anthropometric indicators, although body composition is more favorable following a slow WL. Both diets improved lipid and glycemic profiles. In this context, rapid WL was more effective. (IRCT2016010424699N2) PMID:29201070
Mercury and water level fluctuations in lakes of northern Minnesota
Larson, James H.; Maki, Ryan P; Christensen, Victoria G.; Sandheinrich, Mark B.; LeDuc, Jaime F.; Kissane, Claire; Knights, Brent C.
2017-01-01
Large lake ecosystems support a variety of ecosystem services in surrounding communities, including recreational and commercial fishing. However, many northern temperate fisheries are contaminated by mercury. Annual variation in mercury accumulation in fish has previously been linked to water level (WL) fluctuations, opening the possibility of regulating water levels in a manner that minimizes or reduces mercury contamination in fisheries. Here, we compiled a long-term dataset (1997-2015) of mercury content in young-of-year Yellow Perch (Perca flavescens) from six lakes on the border between the U.S. and Canada and examined whether mercury content appeared to be related to several metrics of WL fluctuation (e.g., spring WL rise, annual maximum WL, and year-to-year change in maximum WL). Using simple correlation analysis, several WL metrics appear to be strongly correlated to Yellow Perch mercury content, although the strength of these correlations varies by lake. We also used many WL metrics, water quality measurements, temperature and annual deposition data to build predictive models using partial least squared regression (PLSR) analysis for each lake. These PLSR models showed some variation among lakes, but also supported strong associations between WL fluctuations and annual variation in Yellow Perch mercury content. The study lakes underwent a modest change in WL management in 2000, when winter WL minimums were increased by about 1 m in five of the six study lakes. Using the PLSR models, we estimated how this change in WL management would have affected Yellow Perch mercury content. For four of the study lakes, the change in WL management that occurred in 2000 likely reduced Yellow Perch mercury content, relative to the previous WL management regime.
Opioid receptor blockade and warmth-liking: effects on interpersonal trust and frontal asymmetry
Schweiger, Desirée; Stemmler, Gerhard; Burgdorf, Christin
2014-01-01
The emotion ‘warmth-liking’ (WL) associated with feelings of affection and acceptance is regularly activated in social contexts. WL has been suggested to be more closely related to the consummatory phase of post-goal attainment positive affect than to pre-goal attainment positive affect/approach motivation and to be partly mediated by brain opioids. To validate these assumptions we employed film/imagery to induce either a neutral emotional state or WL in female participants after intake of either placebo or the opioid antagonist naltrexone. Dependent variables were emotion self-report, interpersonal trust (TRUST, i.e. a behavioral indicator of WL) and frontal asymmetry (i.e. an electroencephalogram (EEG) indicator of approach motivation/behavioral activation). We found that participants reported more WL in the placebo/WL group than in the placebo/neutral group and both naltrexone groups. In addition, TRUST increased in the WL group after placebo, but not after naltrexone, and this pattern was reversed in the neutral control groups. Consequently, opioid blockade suppressed or even reversed the effects of the WL induction on the levels of self-report and behavior, respectively. In addition, we observed reduced relative left-frontal asymmetry in the WL (vs neutral) group, consistent with reduced approach motivation. Overall, these results suggest opioidergic influences on WL and TRUST and reduced approach motivation/behavioral activation for the positive emotion WL. PMID:24078107
Kump, David S; Booth, Frank W
2005-01-01
Four-week-old, Fischer–Brown Norway F1-generation male rats were given access to voluntary running wheels for 21 days, and then the wheels were locked for 5 (WL5), 10 (WL10), 29 (WL29), or 53 (WL53) hours. Two other groups (SED5 and SED10) had no access to voluntary running wheels and were killed at the same time as WL5 and WL10, respectively. Absolute and relative epididymal fat mass, mean cell volume, and amount of lipid per cell increased in WL53 relative to all other groups, with no change in cell number. C/EBPα protein levels in epididymal fat were 30% greater in SED5 than in WL5. The rate of triacylglycerol synthesis in epididymal fat was 4.2-fold greater in SED5 than in WL5, increased 14-fold between WLS and WL10, and was 79% lower in SED10 than in WL10. Triacylglycerol synthesis remained at this elevated level (at least 3.5-fold greater than SED5) through WL53. Thus, the rapid increase in epididymal fat mass with the cessation of voluntary wheel running is associated with a prolonged overshoot in epididymal fat triacylglycerol synthesis. Moreover, rats without running wheels had a 9.4% lower body mass after 21 days than those with running wheels. The individual mass of seven different muscles from the hindlimb, upper forelimb, and back were each lower in animals without running wheels, suggesting that physical activity in rapidly growing rats may be requisite for optimal muscle development. PMID:15774517
Gabriel, Emmanuel; Singla, Smit; Kim, Minhyung; Fisher, Daniel; Powers, Colin; Visioni, Anthony; Attwood, Kristopher; Skitzki, Joseph
2018-01-01
Background Water lavage (WL) during gastrointestinal cancer surgery has osmotically mediated lytic effects on tumor cells. We investigated the safety and efficacy of WL with CRS-HIPEC. Methods This is a retrospective review, 1/2003–7/2014, of a single institution experience with CRS-HIPEC comparing patients who had WL (WL+) to those who did not (WL−). Results Of 157 CRS-HIPECs, 16 (10.2%) were WL+. WL+ had more PCI scores > 20 compared to WL− (56.3% vs 19.4%, respectively, p=0.003); however, the completeness of cytoreduction (CC) was similar. There were no differences in hospital length of stay or post-operative complications. The average POD 1 sodium (Na) level was statistically lower in the WL+ group (133.6±2.5 vs 135.5±3.2 mEq/L, p=0.023); however, the average Na at discharge for each group was 140 mEq/L. There were no differences in 3-year OS (3WL+:0.63 vs WL−:0.68, p=0.97) or RFS (WL+:0.32 vs WL−:0.39, p=0.47). A subset analysis for patients with PCI > 20 showed no difference between groups. Conclusions WL offers a low cost, safe and theoretically efficacious method of tumor cell lysis for peritoneal malignancy. PMID:28622839
Nymo, Siren; Coutinho, Silvia R; Torgersen, Linn-Christin H; Bomo, Ola J; Haugvaldstad, Ingrid; Truby, Helen; Kulseng, Bård; Martins, Catia
2018-07-01
Diet-induced weight loss (WL) is associated with reduced resting and non-resting energy expenditure (EE), driven not only by changes in body composition but also potentially by adaptive thermogenesis (AT). When exactly this happens, during progressive WL, remains unknown. The aim of this study was to determine the timeline of changes in RMR and exercise-induced EE (EIEE), stemming from changes in body composition v. the presence of AT, during WL with a very-low-energy diet (VLED). In all, thirty-one adults (eighteen men) with obesity (BMI: 37 (sem 4·5) kg/m2; age: 43 (sem 10) years) underwent 8 weeks of a VLED, followed by 4 weeks of weight maintenance. Body weight and composition, RMR, net EIEE (10, 25 and 50 W) and AT (for RMR (ATRMR) and EIEE (ATEIEE)) were measured at baseline, day 3 (2 (sem 1) % WL), after 5 and 10 % WL and at weeks 9 (16 (sem 2) %) and 13 (16 (sem 1) %). RMR and fat mass were significantly reduced for the first time at 5 % WL (12 (sem 8) d) (P<0·01 and P<0·001, respectively) and EIEE at 10 % WL (32 (sem 8) d), for all levels of power (P<0·05), and sustained up to week 13. ATRMR was transiently present at 10 % WL (-460 (sem 690) kJ/d, P<0·01). A fall in RMR should be anticipated at ≥5 % WL and a reduction in EIEE at ≥10 % WL. Transient ATRMR can be expected at 10 % WL. These physiological adaptations may make progressive WL difficult and will probably contribute to relapse.
NASA Astrophysics Data System (ADS)
Kim, Jungho; Yu, Bong-Ahn
2015-03-01
We numerically investigate the effect of the wetting-layer (WL) density of states on the gain and phase recovery dynamics of quantum-dot semiconductor optical amplifiers in both electrical and optical pumping schemes by solving 1088 coupled rate equations. The temporal variations of the ultrafast gain and phase recovery responses at the ground state (GS) are calculated as a function of the WL density of states. The ultrafast gain recovery responses do not significantly depend on the WL density of states in the electrical pumping scheme and the three optical pumping schemes such as the optical pumping to the WL, the optical pumping to the excited state ensemble, and the optical pumping to the GS ensemble. The ultrafast phase recovery responses are also not significantly affected by the WL density of states except the optical pumping to the WL, where the phase recovery component caused by the WL becomes slowed down as the WL density of states increases.
1994-08-01
721 An Improved G-Tracking Method for Large Transport Aircraft ............................ 741 iv Naval aircraft Approach and...E. B. de la Motte Swedish Defence Materiel Administration, Stockholm, Sweden Capt F. A. Opaiski WL/FIBEC 090040930 An Aircraft Structural Integrity...M. Poole Canadian Transportation Safety Board 1400-1430 The Challenges Associated with the Operation of Loads Monitoring Equipment for Efficient
Timeline of changes in appetite during weight loss with a ketogenic diet
Nymo, S; Coutinho, S R; Jørgensen, J; Rehfeld, J F; Truby, H; Kulseng, B; Martins, C
2017-01-01
Background/objective: Diet-induced weight loss (WL) leads to increased hunger and reduced fullness feelings, increased ghrelin and reduced satiety peptides concentration (glucagon-like peptide-1 (GLP-1), cholecystokinin (CCK) and peptide YY (PYY)). Ketogenic diets seem to minimise or supress some of these responses. The aim of this study was to determine the timeline over which changes in appetite occur during progressive WL with a ketogenic very-low-energy diet (VLED). Subjects/methods: Thirty-one sedentary adults (18 men), with obesity (body mass index: 37±4.5 kg m−2) underwent 8 weeks (wks) of a VLED followed by 4 wks of weight maintenance. Body weight and composition, subjective feelings of appetite and appetite-related hormones (insulin, active ghrelin (AG), active GLP-1, total PYY and CCK) were measured in fasting and postprandially, at baseline, on day 3 of the diet, 5 and 10% WL, and at wks 9 and 13. Data are shown as mean±s.d. Results: A significant increase in fasting hunger was observed by day 3 (2±1% WL), (P<0.01), 5% WL (12±8 days) (P<0.05) and wk 13 (17±2% WL) (P<0.05). Increased desire to eat was observed by day 3 (P<0.01) and 5% WL (P<0.05). Postprandial prospective food consumption was significantly reduced at wk 9 (16±2% WL) (P<0.01). Basal total PYY was significantly reduced at 10% WL (32±8 days) (P<0.05). Postprandial active GLP-1 was increased at 5% WL (P<0.01) and CCK reduced at 5 and 10% WL (P<0.01, for both) and wk 9 (P<0.001). Basal and postprandial AG were significantly increased at wk 13 (P<0.001, both). Conclusions: WL with a ketogenic VLED transiently increases the drive to eat up to 3 weeks (5% WL). After that, and while participants are ketotic, a 10–17% WL is not associated with increased appetite. However, hunger feelings and AG concentrations increase significantly from baseline, once refeeding occurs. PMID:28439092
Timeline of changes in appetite during weight loss with a ketogenic diet.
Nymo, S; Coutinho, S R; Jørgensen, J; Rehfeld, J F; Truby, H; Kulseng, B; Martins, C
2017-08-01
Diet-induced weight loss (WL) leads to increased hunger and reduced fullness feelings, increased ghrelin and reduced satiety peptides concentration (glucagon-like peptide-1 (GLP-1), cholecystokinin (CCK) and peptide YY (PYY)). Ketogenic diets seem to minimise or supress some of these responses. The aim of this study was to determine the timeline over which changes in appetite occur during progressive WL with a ketogenic very-low-energy diet (VLED). Thirty-one sedentary adults (18 men), with obesity (body mass index: 37±4.5 kg m -2 ) underwent 8 weeks (wks) of a VLED followed by 4 wks of weight maintenance. Body weight and composition, subjective feelings of appetite and appetite-related hormones (insulin, active ghrelin (AG), active GLP-1, total PYY and CCK) were measured in fasting and postprandially, at baseline, on day 3 of the diet, 5 and 10% WL, and at wks 9 and 13. Data are shown as mean±s.d. A significant increase in fasting hunger was observed by day 3 (2±1% WL), (P<0.01), 5% WL (12±8 days) (P<0.05) and wk 13 (17±2% WL) (P<0.05). Increased desire to eat was observed by day 3 (P<0.01) and 5% WL (P<0.05). Postprandial prospective food consumption was significantly reduced at wk 9 (16±2% WL) (P<0.01). Basal total PYY was significantly reduced at 10% WL (32±8 days) (P<0.05). Postprandial active GLP-1 was increased at 5% WL (P<0.01) and CCK reduced at 5 and 10% WL (P<0.01, for both) and wk 9 (P<0.001). Basal and postprandial AG were significantly increased at wk 13 (P<0.001, both). WL with a ketogenic VLED transiently increases the drive to eat up to 3 weeks (5% WL). After that, and while participants are ketotic, a 10-17% WL is not associated with increased appetite. However, hunger feelings and AG concentrations increase significantly from baseline, once refeeding occurs.
Ryan, Alice S; Ge, Shealinna; Blumenthal, Jacob B; Serra, Monica C; Prior, Steven J; Goldberg, Andrew P
2014-04-01
To examine the relationships between plasma and tissue markers of systemic and vascular inflammation and obesity and insulin resistance and determine the effects of aerobic exercise training plus weight loss (AEX+WL) and weight loss (WL) alone on these biomarkers. Prospective controlled study. Veterans Affairs Medical Center and University research setting. Overweight and obese sedentary postmenopausal women (N = 77). Six months, 3 d/wk AEX+WL (n = 37) or WL (n = 40). Total-body dual-energy X-ray absorptiometry, abdominal computed tomography, hyperinsulinemic-euglycemic clamps (a criterion standard method of assessing insulin sensitivity), adipose tissue biopsies (n = 28), and blood for homeostasis model assessment-insulin resistance, and soluble forms of intracellular adhesion molecule 1 (sICAM-1) and vascular cell adhesion molecule 1 (sVCAM-1), C-reactive protein (CRP), and serum amyloid A (SAA). Body weight (P < .001), percentage of fat (P < .001), visceral fat (P < .005), triglyceride levels (P < .001), and systolic blood pressure decreased comparably after WL and AEX+WL (P = .04). Maximal oxygen consumption increased 16% after AEX+WL (P < .001). Insulin resistance decreased in both groups (P = .005). Glucose utilization according to the clamp increased 10% (P = .04) with AEX+WL and 8% with WL (P = .07). AEX+WL decreased CRP by 29% (P < .001) and WL by 21% (P = .02). SAA levels decreased twice as much after AEX+WL (-19%, P = .02) as after WL (-9%, P = .08). Plasma sICAM-1 and sVCAM-1 levels did not change, but women with the greatest reduction in plasma sICAM-1 levels had the greatest reductions in fasting glucose (P = .02), insulin (P = .02), and insulin resistance (P = .004). Gluteal ICAM messenger ribonucleic acid levels decreased 27% after AEX+WL (P = .02) and did not change after WL. Obesity and insulin resistance worsen markers of systemic and vascular inflammation. A reduction in plasma sICAM-1 is important to improve insulin sensitivity. CRP, SAA, and tissue ICAM decrease with exercise and weight loss, suggesting that exercise training is a necessary component of lifestyle modification in obese postmenopausal women. © Published 2014. This article is a U.S. Government work and is in the public domain in the U.S.A.
Evolution of wetting layer in InAs/GaAs quantum dot system
Ye, XL; Wang, ZG
2006-01-01
For InAs/GaAs quantum dot system, the evolution of the wetting layer (WL) with the InAs deposition thickness has been studied by reflectance difference spectroscopy (RDS). Two transitions related to the heavy- and light-hole in the WL have been distinguished in RD spectra. Taking into account the strain and segregation effects, a model has been presented to deduce the InAs amount in the WL and the segregation coefficient of the indium atoms from the transition energies of heavy- and light-holes. The variation of the InAs amount in the WL and the segregation coefficient are found to rely closely on the growth modes. In addition, the huge dots also exhibits a strong effect on the evolution of the WL. The observed linear dependence of In segregation coefficient upon the InAs amount in the WL demonstrates that the segregation is enhanced by the strain in the WL.
Ahn, Jin Hwan; Wang, Joon Ho; Kim, Dong Uk; Lee, Do Kyung; Kim, Jun Ho
2017-12-01
The aim of this study was to evaluate the relationship between discoid lateral meniscus (DLM) types based on peripheral detachment and anatomic features of Wrisberg ligament (WL) such as location and thickness based on magnetic resonance image (MRI). A total of 322 knees in 292 patients were reviewed. Patients were divided into four DLM types according to peripheral detachment: no shift (type 1), anterocentral shift (type 2), posterocentral shift (type 3) and central shift (type 4). We reviewed all MRI concentrating on the presence, location (high or low location), running angle, thickness of WL, and WL/posterior cruciate ligament (PCL) thickness ratio. The relationship between DLM types and anatomic features of WL were analyzed using one-way analysis of variance and chi-square test. According to DLM types based on peripheral detachment, 149 knees were type 1, 38 were type 2, 79 were type 3, and 56 were type 4. Among the 322 knees, 302 (93.8%) had WL on MRI. In DLM patients, type 3 showed a statistically significant (P<0.001) relationship with high location of WL. In addition, type 3 had significantly larger (P<0.0001) running angle of WL, thicker (P<0.0001) WL, and higher (P<0.0001) WL/PCL ratio compared to other types. A high location and thick WL are related to posterocentral shift type of DLM based on peripheral detachment. Based on our results, the high location and thick WL might provide information to surgeons in predicting the direction of peripheral detachment in symptomatic DLM patients. Copyright © 2017 Elsevier B.V. All rights reserved.
Soni, Dileep; Raisingani, Deepak; Mathur, Rachit; Madan, Nidha; Visnoi, Suchita
2016-01-01
To evaluate the incidence of apical crack initiation during canal preparation with stainless steel K-files and hand protaper files (in vitro study). Sixty extracted mandibular premo-lar teeth are randomly selected and embedded in an acrylic tube filled with autopolymerizing resin. A baseline image of the apical surface of each specimen was recorded under a digital microscope (80×). The cervical and middle thirds of all samples were flared with #2 and #1 Gates-Glidden (GG) drills, and a second image was recorded. The teeth were randomly divided into four groups of 15 teeth each according to the file type (hand K-file and hand-protaper) and working length (WL) (instrumented at WL and 1 mm less than WL). Final image after dye penetration and photomicrograph of the apical root surface were digitally recorded. Maximum numbers of cracks were observed with hand protaper files compared with hand K-file at the WL and 1 mm short of WL. Chi-square testing revealed a highly significant effect of WL on crack formation at WL and 1 mm short of WL (p = 0.000). Minimum numbers of cracks at WL and 1 mm short of WL were observed with hand K-file and maximum with hand protaper files. Soni D, Raisingani D, Mathur R, Madan N, Visnoi S. Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files. Int J Clin Pediatr Dent 2016;9(4):303-307.
Study of indoor radon and thoron progeny levels in surrounding areas of Nalbari, Assam, India
NASA Astrophysics Data System (ADS)
Deka, P. C.; Sarma, H.; Sarkar, Subir; Goswami, T. D.; Sarma, B. K.
2009-07-01
With the growing understanding of the role of radon and its daughter products as major sources of radiation exposure, the importance of large number of estimation of radon concentration in various parts of the country is realized. Inhalation of radon, thoron and their decay products is the major source of the total radioactive dose received by the human population from natural radiation. The indoor radon and thoron progeny levels in Nalbari area of Assam are studied by using the LR-115 (type II) Solid State Nuclear Track Detector in Plastic Twin Chamber dosimeter. Radon and thoron progeny levels in different types of dwellings for one full calendar year are presented in this paper. For Assam Type (A.T.) houses, indoor radon progeny concentrations vary from 0.17 to 0.64 mWL with an annual geometric mean of 0.27 mWL and that for Reinforced Cement Concrete (R.C.C.) houses vary from 0.22 mWL to 0.60 mWL with the annual geometric mean of 0.37 mWL. The thoron progeny levels in A.T. houses also vary from 0.01 to of 0.05 mWL with an annual geometric mean of 0.02 mWL and that for R.C.C. houses vary from 0.02 to 0.08 mWL with the annual geometric mean of 0.04 mWL.
Tricoli, Valmor; Lamas, Leonardo; Carnevale, Roberto; Ugrinowitsch, Carlos
2005-05-01
Among sport conditioning coaches, there is considerable discussion regarding the efficiency of training methods that improve lower-body power. Heavy resistance training combined with vertical jump (VJ) training is a well-established training method; however, there is a lack of information about its combination with Olympic weightlifting (WL) exercises. Therefore, the purpose of this study was to compare the short-term effects of heavy resistance training combined with either the VJ or WL program. Thirty-two young men were assigned to 3 groups: WL = 12, VJ = 12, and control = 8. These 32 men participated in an 8-week training study. The WL training program consisted of 3 x 6RM high pull, 4 x 4RM power clean, and 4 x 4RM clean and jerk. The VJ training program consisted of 6 x 4 double-leg hurdle hops, 4 x 4 alternated single-leg hurdle hops, 4 x 4 single-leg hurdle hops, and 4 x 4 40-cm drop jumps. Additionally, both groups performed 4 x 6RM half-squat exercises. Training volume was increased after 4 weeks. Pretesting and posttesting consisted of squat jump (SJ) and countermovement jump (CMJ) tests, 10- and 30-m sprint speeds, an agility test, a half-squat 1RM, and a clean-and-jerk 1RM (only for WL). The WL program significantly increased the 10-m sprint speed (p < 0.05). Both groups, WL and VJ, increased CMJ (p < 0.05), but groups using the WL program increased more than those using the VJ program. On the other hand, the group using the VJ program increased its 1RM half-squat strength more than the WL group (47.8 and 43.7%, respectively). Only the WL group improved in the SJ (9.5%). There were no significant changes in the control group. In conclusion, Olympic WL exercises seemed to produce broader performance improvements than VJ exercises in physically active subjects.
Nouchi, Rui; Taki, Yasuyuki; Takeuchi, Hikaru; Nozawa, Takayuki; Sekiguchi, Atsushi; Kawashima, Ryuta
2016-01-01
Background: Previous reports have described that simple cognitive training using reading aloud and solving simple arithmetic calculations, so-called “learning therapy”, can improve executive functions and processing speed in the older adults. Nevertheless, it is not well-known whether learning therapy improve a wide range of cognitive functions or not. We investigated the beneficial effects of learning therapy on various cognitive functions in healthy older adults. Methods: We used a single-blinded intervention with two groups (learning therapy group: LT and waiting list control group: WL). Sixty-four elderly were randomly assigned to LT or WL. In LT, participants performed reading Japanese aloud and solving simple calculations training tasks for 6 months. WL did not participate in the intervention. We measured several cognitive functions before and after 6 months intervention periods. Results: Compared to WL, results revealed that LT improved inhibition performance in executive functions (Stroop: LT (Mean = 3.88) vs. WL (Mean = 1.22), adjusted p = 0.013 and reverse Stroop LT (Mean = 3.22) vs. WL (Mean = 1.59), adjusted p = 0.015), verbal episodic memory (Logical Memory (LM): LT (Mean = 4.59) vs. WL (Mean = 2.47), adjusted p = 0.015), focus attention (D-CAT: LT (Mean = 2.09) vs. WL (Mean = −0.59), adjusted p = 0.010) and processing speed compared to the WL control group (digit symbol coding: LT (Mean = 5.00) vs. WL (Mean = 1.13), adjusted p = 0.015 and Symbol Search (SS): LT (Mean = 3.47) vs. WL (Mean = 1.81), adjusted p = 0.014). Discussion: This randomized controlled trial (RCT) can be showed the benefit of LT on inhibition of executive functions, verbal episodic memory, focus attention and processing speed in healthy elderly people. Our results were discussed under overlapping hypothesis. PMID:27242481
Nikolić, Marko; Kruljac, Ivan; Kirigin, Lora; Mirošević, Gorana; Ljubičić, Neven; Nikolić, Borka Pezo; Bekavac-Bešlin, Miroslav; Budimir, Ivan; Vrkljan, Milan
2015-06-01
Background: Bariatric procedures are effective options for weight loss (WL) in the morbidly obese. However, some patients fail to lose any weight after bariatric surgery, and mid-term weight maintenance is variable. The aim of this study was to investigate whether initial WL could predict mid-term weight maintenance. Methods: Eighty patients were enrolled, of whom 44 were treated with the BioEnterics Intragastric Balloon (BIB), 21 with laparoscopic adjustable gastric lap-banding (LAGB), and 15 with laparoscopic sleeve gastrectomy (LSG). Percentage of body WL and percentage of excess weight loss (EWL) were calculated at baseline and after 1, 3, 6, and 12 months. Successful WL was defined as EWL >20% for patients treated with BIB and >50% for patients treated with LAGB and SG. Results: Success in the 6th and 12th month was achieved in 80% and 58% of patients in the BIB group, 33% and 40% in the LAGB group, and 60% and 73% in the LSG group. In the BIB group, WL in the 1st month correlated positively with WL at the 6th and 12th month, and an initial WL >6.5% best predicted success (sensitivity 50%, specificity 80%). A similar association was observed in the LAGB group at the 6th and 12th month and an initial WL >9.4% best predicted success (sensitivity 90.0%, specificity 81.2%). In patients treated with LSG, WL in the 3rd month correlated positively with EWL at the 6th and 12th month, with a cutoff value of 17% (sensitivity 66.7%, specificity 100%). Conclusions: WL in the 1st month in patients treated with BIB and LAGB and WL in the 3rd month in patients treated with LSG could be used as a prognostic factor to predict mid-term weight maintenance.
Nouchi, Rui; Taki, Yasuyuki; Takeuchi, Hikaru; Nozawa, Takayuki; Sekiguchi, Atsushi; Kawashima, Ryuta
2016-01-01
Previous reports have described that simple cognitive training using reading aloud and solving simple arithmetic calculations, so-called "learning therapy", can improve executive functions and processing speed in the older adults. Nevertheless, it is not well-known whether learning therapy improve a wide range of cognitive functions or not. We investigated the beneficial effects of learning therapy on various cognitive functions in healthy older adults. We used a single-blinded intervention with two groups (learning therapy group: LT and waiting list control group: WL). Sixty-four elderly were randomly assigned to LT or WL. In LT, participants performed reading Japanese aloud and solving simple calculations training tasks for 6 months. WL did not participate in the intervention. We measured several cognitive functions before and after 6 months intervention periods. Compared to WL, results revealed that LT improved inhibition performance in executive functions (Stroop: LT (Mean = 3.88) vs. WL (Mean = 1.22), adjusted p = 0.013 and reverse Stroop LT (Mean = 3.22) vs. WL (Mean = 1.59), adjusted p = 0.015), verbal episodic memory (Logical Memory (LM): LT (Mean = 4.59) vs. WL (Mean = 2.47), adjusted p = 0.015), focus attention (D-CAT: LT (Mean = 2.09) vs. WL (Mean = -0.59), adjusted p = 0.010) and processing speed compared to the WL control group (digit symbol coding: LT (Mean = 5.00) vs. WL (Mean = 1.13), adjusted p = 0.015 and Symbol Search (SS): LT (Mean = 3.47) vs. WL (Mean = 1.81), adjusted p = 0.014). This randomized controlled trial (RCT) can be showed the benefit of LT on inhibition of executive functions, verbal episodic memory, focus attention and processing speed in healthy elderly people. Our results were discussed under overlapping hypothesis.
Raisingani, Deepak; Mathur, Rachit; Madan, Nidha; Visnoi, Suchita
2016-01-01
Aim To evaluate the incidence of apical crack initiation during canal preparation with stainless steel K-files and hand protaper files (in vitro study). Materials and methods Sixty extracted mandibular premo-lar teeth are randomly selected and embedded in an acrylic tube filled with autopolymerizing resin. A baseline image of the apical surface of each specimen was recorded under a digital microscope (80×). The cervical and middle thirds of all samples were flared with #2 and #1 Gates-Glidden (GG) drills, and a second image was recorded. The teeth were randomly divided into four groups of 15 teeth each according to the file type (hand K-file and hand-protaper) and working length (WL) (instrumented at WL and 1 mm less than WL). Final image after dye penetration and photomicrograph of the apical root surface were digitally recorded. Results Maximum numbers of cracks were observed with hand protaper files compared with hand K-file at the WL and 1 mm short of WL. Chi-square testing revealed a highly significant effect of WL on crack formation at WL and 1 mm short of WL (p = 0.000). Conclusion Minimum numbers of cracks at WL and 1 mm short of WL were observed with hand K-file and maximum with hand protaper files. How to cite this article Soni D, Raisingani D, Mathur R, Madan N, Visnoi S. Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files. Int J Clin Pediatr Dent 2016;9(4):303-307. PMID:28127160
Ryan, Alice S; Serra, Monica C; Goldberg, Andrew P
2018-01-01
To determine the 6-month follow-up effects after intentional 6-month weight loss alone (WL) and after weight loss with aerobic exercise (AEX + WL) on body composition, glucose metabolism, and cardiovascular disease risk factors in older postmenopausal women and to identify the mechanisms for weight regain. Women (n = 65, BMI > 25 kg/m 2 ) underwent maximal oxygen consumption testing, dual-energy x-ray absorptiometry, computed tomography scans, and oral glucose tolerance tests before and after 6 months of AEX + WL or WL and at 12 months ad libitum follow-up. Insulin sensitivity (M) (hyperinsulinemic-euglycemic clamp) was measured at baseline and 6 months. Thirty WL and thirty-five AEX + WL women completed a follow-up at 12 months. Similar weight loss was observed (-8%) in both groups from 0 to 6 months. Total fat mass, fat-free mass, visceral fat area, subcutaneous abdominal and midthigh fat areas, fasting glucose, insulin levels, homeostatic model assessment of insulin resistance (HOMA-IR), insulin areas under the curve, and triglyceride levels decreased similarly after WL and AEX + WL and remained lower at 12 months than at baseline, despite weight regain at 12 months. Initial M was associated with weight regain (r = -0.40, P < 0.01). Weight regain was related to independent changes in leptin and HOMA-IR from 6 to 12 months in a multiple regression model (r = 0.77, P < 0.0001). Reductions in body fat and improvements in insulin sensitivity after AEX + WL and WL were maintained at 12 months despite modest weight regain. Baseline insulin resistance partially predicted the magnitude of weight regain in postmenopausal women. © 2017 The Obesity Society.
Gallicchio, Lisa; Helzlsouer, Kathy J; Audlin, Kevin M; Miller, Charles; MacDonald, Ryan; Johnston, Mary; Barrueto, Fermin F
2015-01-01
To examine whether the addition of narrow band imaging (NBI) to traditional white light imaging during laparoscopic surgery impacts pain and quality of life (QOL) at 3 and 6 months after surgery among women with suspected endometriosis and/or infertility. A randomized controlled trial (Canadian Task Force classification level I). The trial was conducted in 2 medical centers. From October 2011 to November 2013, 167 patients undergoing laparoscopic examination for suspected endometriosis and/or infertility were recruited. The analytic study sample includes 148 patients with pain and QOL outcome data. Patients were randomized in a 3:1 ratio to receive white light imaging followed by NBI (WL/NBI) or white light imaging only (WL/WL). Questionnaires were administered at baseline and at 3- and 6-month follow-up time points. Average and most severe pain at each time point were assessed using a 10-cm visual analog scale. QOL was measured using the Endometriosis Health Profile-30. Baseline characteristics were similar for the study groups. The WL/NBI and WL/WL groups had similar reductions in pain at 3 and 6 months. In addition, QOL improved similarly for both the WL/NBI and WL/WL groups at 3 and 6 months. Laparoscopic surgery for suspected endometriosis is associated with a reduction in pain and an improvement in QOL. The differences in pain reduction and QOL improvement, which are noted at 3 months and remain stable at 6 months after surgery, are similar for those undergoing surgery with WL/NBI compared with those undergoing surgery under traditional white light conditions. Copyright © 2015 AAGL. Published by Elsevier Inc. All rights reserved.
NASA Astrophysics Data System (ADS)
Straková, P.; Niemi, R. M.; Freeman, C.; Peltoniemi, K.; Toberman, H.; Heiskanen, I.; Fritze, H.; Laiho, R.
2011-02-01
Peatlands are carbon (C) storage ecosystems sustained by a high water level (WL). High WL creates anoxic conditions that suppress the activity of aerobic decomposers and provide conditions for peat accumulation. Peatland function can be dramatically affected by WL drawdown caused by land-use and/or climate change. Aerobic decomposers are directly affected by WL drawdown through environmental factors such as increased oxygenation and nutrient availability. Additionally, they are indirectly affected via changes in plant community composition and litter quality. We studied the relative importance of direct and indirect effects of WL drawdown on aerobic decomposer activity in plant litter. We did this by profiling 11 extracellular enzymes involved in the mineralization of organic C, nitrogen, phosphorus and sulphur. Our study sites represented a three-stage chronosequence from pristine (undrained) to short-term (years) and long-term (decades) WL drawdown conditions under two nutrient regimes. The litter types included reflected the prevalent vegetation, i.e., Sphagnum mosses, graminoids, shrubs and trees. WL drawdown had a direct and positive effect on microbial activity. Enzyme allocation shifted towards C acquisition, which caused an increase in the rate of decomposition. However, litter type overruled the direct effects of WL drawdown and was the main factor shaping microbial activity patterns. Our results imply that changes in plant community composition in response to persistent WL drawdown will strongly affect the C dynamics of peatlands.
Muscle fiber characteristics and performance correlates of male Olympic-style weightlifters.
Fry, Andrew C; Schilling, Brian K; Staron, Robert S; Hagerman, Fredrick C; Hikida, Robert S; Thrush, John T
2003-11-01
Biopsies fro the vastus lateralis muscle of male weightlifters (WL; n=6; X +/- SE, age=27.0 +/- 2.1 years), and non-weight-trained men (CON; n=7; age=27.0 +/- 2.0 years) were compared for fiber types, myosin heavy chain (MHC) and titin content, and fiber type-specific capillary density. Differences (p<0.05) were observed for percent fiber types IIC (WL=0.4 +/- 0.2, CON=2.4 +/- 0.8); IIA (WL=50.5 +/- 3.2, CON=26.9 +/- 3.7); and IIB (WL=1.7 +/- 1.4, CON=21.0 +/- 5.3), as well as percent MHC IIa (WL=65.3 +/- 2.4, CON=52.1 +/- 4.2) and percent MHC IIB (WL=0.9 +/- 0.9; CON=18.2 +/- 6.1). All WL exhibited only the titin-1 isoform. Capillary density (caps.mm(-2)) for all fiber types combined was greater for the CON subjects (WL=192.7 +/- 17.3; CON=262.9 +/- 26.3), due primarily to a greater capillary density in the IIA fibers. Weightlifting performances and vertical jump power were correlated with type II fiber characteristics. These results suggest that successful weightlifting performance is not dependent on IIB fibers, and that weightlifters exhibit large percentages of type IIA muscle fibers and MHC IIa isoform content.
Caria, Cíntia Rabelo E Paiva; Gotardo, Érica Martins Ferreira; Santos, Paola Souza; Acedo, Simone Coghetto; de Morais, Thainá Rodrigues; Ribeiro, Marcelo Lima; Gambero, Alessandra
2017-10-15
Extracellular matrix (ECM) remodeling is necessary for a health adipose tissue (AT) expansion and also has a role during weight loss. We investigate the ECM alteration during weight cycling (WC) in mice and the role of matrix metalloproteinases (MMPs) was assessed using GM6001, an MMP inhibitor, during weight loss (WL). Obesity was induced in mice by a high-fat diet. Obese mice were subject to caloric restriction for WL followed by reintroduction to high-fat diet for weight regain (WR), resulting in a WC protocol. In addition, mice were treated with GM6001 during WL period and the effects were observed after WR. Activity and expression of MMPs was intense during WL. MMP inhibition during WL results in inflammation and collagen content reduction. MMP inhibition during WL period interferes with the period of subsequent expansion of AT resulting in improvements in local inflammation and systemic metabolic alterations induced by obesity. Our results suggest that MMPs inhibition could be an interesting target to improve adipose tissue inflammation during WL and to support weight cyclers. Copyright © 2017 Elsevier Inc. All rights reserved.
Prior Consumption of a Fat Meal in Healthy Adults Modulates the Brain’s Response to Fat123
Eldeghaidy, Sally; Hort, Joanne; Hollowood, Tracey; Singh, Gulzar; Bush, Debbie; Foster, Tim; Taylor, Andy J; Busch, Johanneke; Spiller, Robin C
2016-01-01
Background: The consumption of fat is regulated by reward and homeostatic pathways, but no studies to our knowledge have examined the role of high-fat meal (HFM) intake on subsequent brain activation to oral stimuli. Objective: We evaluated how prior consumption of an HFM or water load (WL) modulates reward, homeostatic, and taste brain responses to the subsequent delivery of oral fat. Methods: A randomized 2-way crossover design spaced 1 wk apart was used to compare the prior consumption of a 250-mL HFM (520 kcal) [rapeseed oil (440 kcal), emulsifier, sucrose, flavor cocktail] or noncaloric WL on brain activation to the delivery of repeated trials of a flavored no-fat control stimulus (CS) or flavored fat stimulus (FS) in 17 healthy adults (11 men) aged 25 ± 2 y and with a body mass index (in kg/m2) of 22.4 ± 0.8. We tested differences in brain activation to the CS and FS and baseline cerebral blood flow (CBF) after the HFM and WL. We also tested correlations between an individual’s plasma cholecystokinin (CCK) concentration after the HFM and blood oxygenation level–dependent (BOLD) activation of brain regions. Results: Compared to the WL, consuming the HFM led to decreased anterior insula taste activation in response to both the CS (36.3%; P < 0.05) and FS (26.5%; P < 0.05). The HFM caused reduced amygdala activation (25.1%; P < 0.01) in response to the FS compared to the CS (fat-related satiety). Baseline CBF significantly reduced in taste (insula: 5.7%; P < 0.01), homeostatic (hypothalamus: 9.2%, P < 0.01; thalamus: 5.1%, P < 0.05), and reward areas (striatum: 9.2%; P < 0.01) after the HFM. An individual’s plasma CCK concentration correlated negatively with brain activation in taste and oral somatosensory (ρ = −0.39; P < 0.05) and reward areas (ρ = −0.36; P < 0.05). Conclusions: Our results in healthy adults show that an HFM suppresses BOLD activation in taste and reward areas compared to a WL. This understanding will help inform the reformulation of reduced-fat foods that mimic the brain’s response to high-fat counterparts and guide future interventions to reduce obesity. PMID:27655761
Prior Consumption of a Fat Meal in Healthy Adults Modulates the Brain's Response to Fat.
Eldeghaidy, Sally; Marciani, Luca; Hort, Joanne; Hollowood, Tracey; Singh, Gulzar; Bush, Debbie; Foster, Tim; Taylor, Andy J; Busch, Johanneke; Spiller, Robin C; Gowland, Penny A; Francis, Susan T
2016-11-01
The consumption of fat is regulated by reward and homeostatic pathways, but no studies to our knowledge have examined the role of high-fat meal (HFM) intake on subsequent brain activation to oral stimuli. We evaluated how prior consumption of an HFM or water load (WL) modulates reward, homeostatic, and taste brain responses to the subsequent delivery of oral fat. A randomized 2-way crossover design spaced 1 wk apart was used to compare the prior consumption of a 250-mL HFM (520 kcal) [rapeseed oil (440 kcal), emulsifier, sucrose, flavor cocktail] or noncaloric WL on brain activation to the delivery of repeated trials of a flavored no-fat control stimulus (CS) or flavored fat stimulus (FS) in 17 healthy adults (11 men) aged 25 ± 2 y and with a body mass index (in kg/m 2 ) of 22.4 ± 0.8. We tested differences in brain activation to the CS and FS and baseline cerebral blood flow (CBF) after the HFM and WL. We also tested correlations between an individual's plasma cholecystokinin (CCK) concentration after the HFM and blood oxygenation level-dependent (BOLD) activation of brain regions. Compared to the WL, consuming the HFM led to decreased anterior insula taste activation in response to both the CS (36.3%; P < 0.05) and FS (26.5%; P < 0.05). The HFM caused reduced amygdala activation (25.1%; P < 0.01) in response to the FS compared to the CS (fat-related satiety). Baseline CBF significantly reduced in taste (insula: 5.7%; P < 0.01), homeostatic (hypothalamus: 9.2%, P < 0.01; thalamus: 5.1%, P < 0.05), and reward areas (striatum: 9.2%; P < 0.01) after the HFM. An individual's plasma CCK concentration correlated negatively with brain activation in taste and oral somatosensory (ρ = -0.39; P < 0.05) and reward areas (ρ = -0.36; P < 0.05). Our results in healthy adults show that an HFM suppresses BOLD activation in taste and reward areas compared to a WL. This understanding will help inform the reformulation of reduced-fat foods that mimic the brain's response to high-fat counterparts and guide future interventions to reduce obesity.
Kumar, Rahul; Khambete, Neha; Patil, Suvarna; Hoshing, Upendra; Medha, Ashish; Shetty, Roshan
2013-09-01
This in vitro investigation examined the effect of early coronal flaring (CF) and late CF on the working length (WL) in curved root canals. The objective of this study was to determine if canal length is altered as a result of CF in curved canals of molar roots. The conditions compared were combinations of (a) stainless steel hand files using Gates Glidden (G. G.) drills (SS) versus nickel-titanium rotary files (Ni-Ti); and (b) early CF (flaring completed before WL determination) versus late CF (flaring completed after WL determination). Selected were 90 canals of extracted maxillary or mandibular first molars (mesial root of mandibular molars and the mesiobuccal root of the maxillary molars) from three groups. CF was accomplished for the SS group using G. G. drills and for the Ni-Ti group using rotary ProTaper and Hero Shaper files. WL was determined by a digital vernier caliper before CF, immediately after CF, and again after canal preparation. A repeated measures analysis of variance (ANOVA) test and a Tukey's multiple prosthoc test were used for this study. Results indicated that WL decreased for all canals as a result of canal preparation. The mean decrease in WL was significantly greater for the SS group (-0.77 ± 0.42 mm) than for the Ni-Ti groups (-0.33 mm ± 0.44). Less change in WL occurred in all groups when initial WL was determined after CF. WL in curved canals consistently decreases during the course of instrumentation. Clinician should keep this in mind for better treatment outcome.
Stelle, Lacey; Schoenheit, Taylor; Brubaker, Allison; Tang, Xiwei; Qu, Peiyong; Cradock, Kimberly; Higham, Anna
2018-01-01
Radioactive seed localization (RSL) is a safe and effective alternative to wire localization (WL) for nonpalpable breast lesions. While several large academic institutions currently utilize RSL, few community hospitals have adopted this technique. The aim of this study was to examine the experience of RSL versus WL at a large community hospital. A retrospective chart review of patients who underwent RSL or WL for breast-conserving surgery from 1 November 2013 to 31 November 2015. The total number of lesions examined was 382. RSL was utilized in 205 (54%) lesions, with 187 undergoing single RSL, while WL was used in 155 (40%) lesions, with 109 undergoing single WL; both techniques were used in 22 (6%) lesions. Pathology was benign in 142 (48%) lesions, with 93 RSLs and 49 WLs. For malignant lesions, mean specimen size was 36.3 g for single RSL and 35.9 g for single WL (p = 0.904). Re-excision for margin clearance was required for 16 (17%) malignant lesions in the RSL group and 10 (17%) in the WL group (p = 0.954). For malignant lesions, mean operating room time was 86 min for single RSL versus 70 min for single WL (p = 0.014). The use of RSL is a viable option in the community setting, with several benefits over WL. While operative times were slightly longer with RSL, there was no difference in specimen size or re-excision rate for malignant lesions.
Ting, Rachel Sing-Kiat; Wong, Ee-Lynn; Tnay, Jessie Koh-Sing
2018-01-01
Female condom (FC) has been available for over 30 years, but it still lacks wide acceptability. To overcome misdirection and invagination occurring in FC and to provide a wider area of protection, Wondaleaf ® (WL), a new-generation adhesive FC, was recently invented. This pioneering study sought to assess the acceptability and functional performance of WL among Malaysian women. A mixed method survey was conducted in three cities of Malaysia, recruiting sexually active heterosexual women, aged 18-50, by snowball sampling method. Participants were provided with WL and initially surveyed to rate its performance in five coital usages over 2 months. After that, the participants underwent a second survey to rate their satisfaction and acceptability toward WL. Descriptive statistics on clinical failure rates were tabulated with correlational analysis performed to identify major variables contributing to WL's functional performance and acceptability. Out of the 51 enrolled participants, 31 women completed the required surveys. WL's total clinical failure rate was 2.60% (out of 155 condom uses) with above-average ratings of functional performance. The ease of use significantly correlated with ratings of no slippage and no misdirection. The confidence in WL's safety features significantly correlated with a sense of empowerment and protection. WL has a relatively low risk of clinical failures and an overall favorable acceptability among Malaysian women. However, this study also showed that its future usage largely depends on partner acceptability. It may have the potential of complementing the existing barrier toward contraceptive use. Further studies are needed to understand the global acceptability of WL.
Kulovitz, Michelle G; Kolkmeyer, Deborah; Conn, Carole A; Cohen, Deborah A; Ferraro, Robert T
2014-01-01
The aim of this study was to investigate body composition changes in fat mass (FM) to lean body mass (LBM) ratios following 15% body weight loss (WL) in both integrated medical treatment and bariatric surgery groups. Obese patients (body mass index [BMI] 46.6 ± 6.5 kg/m(2)) who underwent laparoscopic gastric bypass surgery (BS), were matched with 24 patients undergoing integrated medical and behavioral treatment (MT). The BS and MT groups were evaluated for body weight, BMI, body composition, and waist circumference (WC) at baseline and after 15% WL. Following 15% body WL, there were significant decreases in %FM and increased %LBM (P < 0.0001). Additionally, both groups saw 76% of WL from FM, and 24% from LBM indicating a 3:1 ratio of FM to LBM loss during the first 15% reduction in body weight. Finally, no significant differences (P = 0.103) between groups for maintenance of WL at 1 y were found. For both groups, baseline FM was found to be negatively correlated with percentage of weight regained (%WR) at 1 y post-WL (r = -0.457; P = 0.007). Baseline WC and rate of WL to 15% were significant predictors of %WR only in the BS group (r = 0.713; P = 0.020). If followed closely by professionals during the first 15% body WL, patients losing 15% weight by either medical or surgical treatments can attain similar FM:LBM loss ratios and can maintain WL for 1 y. Copyright © 2014 Elsevier Inc. All rights reserved.
RCRA Summary Document for the David Witherspoon 1630 Site, Knoxville, Tennessee
DOE Office of Scientific and Technical Information (OSTI.GOV)
Pfeffer, J.
2008-06-10
The 48-acre David Witherspoon, Inc. (DWI) 1630 Site operated as an unregulated industrial landfill and scrap yard. The Tennessee Division of Superfund (TDSF) closed the landfill in 1974. During the period of operation, the site received solid and liquid wastes from salvage and industrial operations. The site consists of five separate tracts of land including a small portion located across the Norfolk Southern Railroad track. The landfill occupies approximately 5 acres of the site, and roughly 20 acres of the 48 acres contains surface and buried debris associated with the DWI dismantling business operation. Beginning in 1968, the state ofmore » Tennessee licensed DWI to receive scrap metal at the DWI 1630 Site, contaminated with natural uranium and enriched uranium (235U) not exceeding 0.1 percent by weight (TDSF 1990). The U.S. Department of Energy (DOE) has agreed to undertake remedial actions at the DWI 1630 Site as specified under a Consent Order with the Tennessee Department of Environment and Conservation (TDEC) (Consent Order No. 90-3443, April 4, 1991), and as further delineated by a Memorandum of Understanding (MOU) between DOE and the State of Tennessee (MOU Regarding Implementation of Consent Orders, October 6, 1994). The soil and debris removal at the DWI 1630 Site is being performed by Bechtel Jacobs Company LLC (BJC) on behalf of the DOE. Remediation consists of removing contaminated soil and debris from the DWI 1630 site except for the landfill area and repairing the landfill cap. The DWI 1630 remediation waste that is being disposed at the Environmental Management Waste Management Facility (EMWMF) as defined as waste lot (WL) 146.1 and consists primarily of soils and soil like material, incidental debris and secondary waste generated from the excavation of debris and soil from the DWI 1630 site. The WL 146.1 includes soil, soil like material (e.g., shredded or chipped vegetation, ash), discrete debris items (e.g., equipment, drums, large scrap metal, cylinders, and cable) and populations of debris type items (e.g., piles of bricks, small scrap metal, roofing material, scaffolding, and shelving) that are located throughout the DWI 1630 site. The project also generates an additional small volume of secondary waste [e.g., personal protective equipment (PPE), and miscellaneous construction waste] that is bagged and included in bulk soil shipments to the EMWMF. The Waste Acceptance Criteria (WAC) for the EMWMF does not allow for material that does not meet the Resource Conservation and Recovery Act (RCRA) Land Disposal Restrictions (LDRs). The waste being excavated in certain areas of the DWI 1630 site contained soil that did not meet RCRA LDR criteria; therefore this waste had to be segregated for treatment or alternate disposal offsite. This document identifies the approach taken by the DWI 1630 project to further characterize the areas identified during the Phase II Remedial Investigation (RI) as potentially containing RCRA-characteristic waste. This document also describes the methodology used to determine excavation limits for areas determined to be RCRA waste, post excavation sampling, and the treatment and disposal of this material.« less
Reconstructing fish movements between coastal wetland and ...
The use of resources from multiple habitats has been shown to be important to the production of aquatic consumers. To quantify the support of Great Lakes coastal wetland (WL) and nearshore (NS) habitats to yellow perch, we used otolith microchemistry to trace movements between the habitats. WL and NS water and fish samples were collected from lakes Huron and Michigan for water and otolith trace element analysis. Recently deposited otolith-edge Sr:Ca and Ba:Ca from otoliths were strongly correlated with the chemistry of the water in which fish were caught. In general, Sr:Ca and Ba:Ca in otoliths were significantly greater for individuals collected from WL areas. Because of these observed chemical differences between WL and NS habitats, quadratic discriminant function analysis (QDFA) was used to classify individuals with high accuracy to the habitat from which they were collected. We then combined the predictive abilities of QDFA with the otolith chemistry transect data that represents an individuals’ entire life, to classify habitat use through each fish’s life. Our results suggest larval use of WL habitats as well as three life histories for adult yellow perch. These strategies include (1) fish utilizing WL once annually (2) WL residents (3) WL residence as juveniles followed by movement to nearshore as adults. This application represents a novel use of transect otolith microchemistry to reconstruct fish movements between freshwater environments acro
Ortmeyer, Heidi K.; Goldberg, Andrew P.; Ryan, Alice S.
2017-01-01
Objective The effects of six-months weight loss (WL) versus aerobic exercise training (AEX)+WL on fat and skeletal muscle markers of fatty acid metabolism were determined in normal (NGT) and impaired (IGT) glucose tolerant African-American and Caucasian postmenopausal women with overweight/obesity. Methods Fat (gluteal and abdominal) lipoprotein lipase (LPL), and skeletal muscle LPL, acyl-CoA synthase (ACS), β-hydroxacyl-CoA dehydrogenase, carnitine palmitoyltransferase (CPT-1), and citrate synthase (CS) activities were measured at baseline (n=104) and before and after WL (n=34) and AEX+WL (n=37). Results After controlling for age and race, muscle LPL and CPT-1 were lower in IGT, and the ratios of fat/muscle LPL activity were higher in IGT compared to NGT. Muscle LPL was related to insulin sensitivity (M), and inversely related to G120, fasting insulin, and HOMA-IR. AEX+WL decreased abdominal fat LPL and increased muscle LPL, ACS, and CS. The ratios of fat/muscle LPL decreased after AEX+WL. The change in VO2max was related to the changes in LPL, ACS, and CS and inversely related to the changes in fat/muscle LPL activity ratios. Conclusions Six-month AEX+WL, and not WL alone, is capable of enhancing skeletal muscle fatty acid metabolism in postmenopausal African-American and Caucasian women with NGT, IGT, and overweight/obesity. PMID:28547918
Community Weight Loss to Combat Obesity and Disability in At-Risk Older Adults.
Rejeski, W Jack; Ambrosius, Walter T; Burdette, Jonathan H; Walkup, Michael P; Marsh, Anthony P
2017-10-12
Among older, overweight, and obese adults with either cardiovascular disease or the metabolic syndrome, reduced mobility and loss of leg strength are important risk factors for morbidity, disability, and mortality. It is unclear whether community-based approaches to weight loss may be an effective solution to this public health challenge. An 18-month three-site, randomized controlled trial conducted by YMCA staff, with blinded assessors, enrolled 249 older, overweight, and obese adults with either cardiovascular disease or metabolic syndrome with randomization to three interventions: weight loss alone (WL), weight loss + aerobic training (WL + AT), and weight loss + resistance training (WT + RT). The dual primary outcomes were 400-m walk time in seconds and knee extensor strength in Newton meters. All groups lost weight from baseline: average baseline adjusted change of -6.1% (95% confidence interval [CI]: -7.5 to -4.7) for WL only, -8.6% (95% CI: -10.0 to -7.2) for WL + AT, and -9.7% (95% CI: -11.1 to -8.4) for WL + RT. Combined, the two physical activity + WL training groups had greater improvement in walk time than WL alone (mean difference 16.9 seconds [95% CI: 9.7 to 24.0], p < .0001). Baseline adjusted change in knee extensor strength was no greater with WL + RT than WL + AT (mean difference -3.6 Nm [95% CI: -7.5 to 0.3], p = .07). At risk, older, overweight and obese adults can achieve clinically significant reductions in body weight with community-based weight loss programs. The change in percent weight loss and improvements in mobility are significantly enhanced when either RT or AT is combined with dietary WL. © The Author 2017. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.
Reduction in liver transplant wait-listing in the era of direct-acting antiviral therapy.
Flemming, Jennifer A; Kim, W Ray; Brosgart, Carol L; Terrault, Norah A
2017-03-01
Direct-acting antiviral (DAA) therapy, recently approved for patients with decompensated cirrhosis (DC) secondary to hepatitis C virus (HCV), is associated with improved hepatic function. We analyzed trends in liver transplant (LT) wait-listing (WL) to explore potential impact of effective medical therapy on WL registration. This is a cohort study using the Scientific Registry of Transplant Recipients database from 2003 to 2015. A total of 47,591 adults wait-listed for LT from HCV, hepatitis B virus (HBV), and nonalcoholic steatohepatitis (NASH) were identified. LT indication was defined as DC if the Model for End-Stage Liver Disease (MELD) at WL was ≥15 or hepatocellular carcinoma (HCC). Era of listing was divided into interferon (IFN; 2003-2010), protease inhibitor (PI; 2011-2013), and direct-acting antiviral (DAA; 2014-2015). Annual standardized incidence rates of WL were analyzed using Poisson regression. Adjusted incidences of LT WL for DC in HCV patients decreased by 5% in the PI era (P = 0.004) and 32% in the DAA era (P < 0.001) compared to the IFN era. Listing for DC in HBV also decreased in the PI (-17%; P = 0.002) and DAA eras (-24%; P < 0.001). Conversely, WL for DC in NASH increased by 41% in the PI era (P < 0.001) and 81% in the DAA era (P < 0.001). WL for HCC in both the HCV and NASH populations increased in both the PI and DAA eras (P < 0.001 for all) whereas HCC WL in HBV remained stable (P > 0.05 for all). The rate of LT WL for HCV complicated by DC has decreased by over 30% in the era of DAA therapy. Further reductions in WL are anticipated with increased testing, linkage to care, and access to DAA therapy. (Hepatology 2017;65:804-812). © 2016 by the American Association for the Study of Liver Diseases.
Smith, Gordon I; Yoshino, Jun; Kelly, Shannon C; Reeds, Dominic N; Okunade, Adewole; Patterson, Bruce W; Klein, Samuel; Mittendorfer, Bettina
2016-10-11
High-protein (HP) intake during weight loss (WL) therapy is often recommended because it reduces the loss of lean tissue mass. However, HP intake could have adverse effects on metabolic function, because protein ingestion reduces postprandial insulin sensitivity. In this study, we compared the effects of ∼10% WL with a hypocaloric diet containing 0.8 g protein/kg/day and a hypocaloric diet containing 1.2 g protein/kg/day on muscle insulin action in postmenopausal women with obesity. We found that HP intake reduced the WL-induced decline in lean tissue mass by ∼45%. However, HP intake also prevented the WL-induced improvements in muscle insulin signaling and insulin-stimulated glucose uptake, as well as the WL-induced adaptations in oxidative stress and cell structural biology pathways. Our data demonstrate that the protein content of a WL diet can have profound effects on metabolic function and underscore the importance of considering dietary macronutrient composition during WL therapy for people with obesity. Copyright © 2016 The Author(s). Published by Elsevier Inc. All rights reserved.
Larson, James H.; Maki, Ryan P.; Knights, Brent C.; Gray, Brian R.
2014-01-01
Mercury (Hg) contamination of fisheries is a major concern for resource managers of many temperate lakes. Anthropogenic Hg contamination is largely derived from atmospheric deposition within a lake’s watershed, but its incorporation into the food web is facilitated by bacterial activity in sediments. Temporal variation in Hg content of fish (young-of-year yellow perch) in the regulated lakes of the Rainy–Namakan complex (on the border of the United States and Canada) has been linked to water level (WL) fluctuations, presumably through variation in sediment inundation. As a result, Hg contamination of fish has been linked to international regulations of WL fluctuation. Here we assess the relationship between WL fluctuations and fish Hg content using a 10-year dataset covering six lakes. Within-year WL rise did not appear in strongly supported models of fish Hg, but year-to-year variation in maximum water levels (∆maxWL) was positively associated with fish Hg content. This WL effect varied in magnitude among lakes: In Crane Lake, a 1 m increase in ∆maxWL from the previous year was associated with a 108 ng increase in fish Hg content (per gram wet weight), while the same WL change in Kabetogama was associated with only a 5 ng increase in fish Hg content. In half the lakes sampled here, effect sizes could not be distinguished from zero. Given the persistent and wide-ranging extent of Hg contamination and the large number of regulated waterways, future research is needed to identify the conditions in which WL fluctuations influence fish Hg content.
Kumar, Rahul; Khambete, Neha; Patil, Suvarna; Hoshing, Upendra; Medha, Ashish; Shetty, Roshan
2013-01-01
Aim: This in vitro investigation examined the effect of early coronal flaring (CF) and late CF on the working length (WL) in curved root canals. Background: The objective of this study was to determine if canal length is altered as a result of CF in curved canals of molar roots. Study Design: The conditions compared were combinations of (a) stainless steel hand files using Gates Glidden (G. G.) drills (SS) versus nickel-titanium rotary files (Ni-Ti); and (b) early CF (flaring completed before WL determination) versus late CF (flaring completed after WL determination). Selected were 90 canals of extracted maxillary or mandibular first molars (mesial root of mandibular molars and the mesiobuccal root of the maxillary molars) from three groups. CF was accomplished for the SS group using G. G. drills and for the Ni-Ti group using rotary ProTaper and Hero Shaper files. WL was determined by a digital vernier caliper before CF, immediately after CF, and again after canal preparation. Statistical Analysis: A repeated measures analysis of variance (ANOVA) test and a Tukey's multiple prosthoc test were used for this study. Results: Results indicated that WL decreased for all canals as a result of canal preparation. The mean decrease in WL was significantly greater for the SS group (−0.77 ± 0.42 mm) than for the Ni-Ti groups (−0.33 mm ± 0.44). Less change in WL occurred in all groups when initial WL was determined after CF. Conclusion: WL in curved canals consistently decreases during the course of instrumentation. Clinician should keep this in mind for better treatment outcome. PMID:24082566
Aerobic exercise is necessary to improve glucose utilization with moderate weight loss in women.
Ryan, Alice S; Nicklas, Barbara J; Berman, Dora M
2006-06-01
To determine the effects of weight loss (WL) alone and combined with aerobic exercise on visceral adipose tissue (VAT), intramuscular fat, insulin-stimulated glucose uptake, and the rate of decline in free fatty acid (FFA) concentrations during hyperinsulinemia. We studied 33 sedentary, obese (BMI = 32 +/- 1 kg/m(2)) postmenopausal women who completed a 6-month (three times per week) program of either WL alone (n = 16) or WL + aerobic exercise (AEX) (n = 17). Glucose utilization (M) was measured during a 3-hour hyperinsulinemic-euglycemic clamp (40 mU/m(2) per minute). M/I, the amount of glucose metabolized per unit of plasma insulin (I), was used as an index of insulin sensitivity. Body weight, total fat mass, and percentage fat decreased similarly in both groups (p < 0.01). VAT, subcutaneous abdominal adipose tissue, mid-thigh subcutaneous fat, and intramuscular fat decreased to a similar extent in both groups and between 14% and 27% after WL and WL+AEX (p < 0.05). WL alone did not change M or M/I; however, M and M/I increased 15% and 21% after WL+AEX (p < 0.05). Fasting concentrations and rate of decline of FFA did not change in either group. In stepwise regression models to determine the independent predictors of changes in M and M/I, the change in VAT was the single independent predictor of M (r(2) = 0.30) and M/I (r(2) = 0.33). Intramuscular fat decreases similarly with 6 months of moderate WL alone or with aerobic exercise in postmenopausal women. In contrast, only WL combined with exercise results in increased glucose utilization and insulin sensitivity. These findings should be validated in a larger population.
Unick, Jessica L; Pellegrini, Christine A; Demos, Kathryn E; Dorfman, Leah
2017-09-01
There is a large variability in response to behavioral weight loss (WL) programs. Reducing rates of obesity and diabetes may require more individuals to achieve clinically significant WL post-treatment. Given that WL within the first 1-2 months of a WL program is associated with long-term WL, it may be possible to improve treatment outcomes by identifying and providing additional intervention to those with poor initial success (i.e., "early non-responders"). We review the current literature regarding early non-response to WL programs and discuss how adaptive interventions can be leveraged as a strategy to "rescue" early non-responders. Preliminary findings suggest that adaptive interventions, specifically stepped care approaches, offer promise for improving outcomes among early non-responders. Future studies need to determine the optimal time point and threshold for intervening and the type of early intervention to employ. Clinicians and researchers should consider the discussed factors when making treatment decisions.
Weight loss after head and neck cancer: A dynamic relationship with depressive symptoms
Van Liew, Julia R.; Brock, Rebecca L.; Christensen, Alan J.; Karnell, Lucy Hynds; Pagedar, Nitin A.; Funk, Gerry F.
2018-01-01
Background Weight loss (WL) and depressive symptoms are critical head and neck cancer (HNC) outcomes, yet their relation over the illness course is unclear. Methods Associations between self-reported depressive symptoms and objective WL across the year following HNC diagnosis were examined using growth curve modeling techniques (N=564). Results A reciprocal covariation pattern emerged—changes in depressive symptoms over time were associated with same-month changes in WL, t (1148) = 2.05, p = .041, and changes in WL were associated with same-month changes in depressive symptoms, t (556) = 2.43, p = .015. To the extent that depressive symptoms increased, patients lost incrementally more weight than was lost due to the passage of time, and vice versa. Results also suggested that pain and eating-related quality of life might explain the reciprocal association between depressive symptoms and WL. Conclusions In HNC, a transactional interplay between depressive symptoms and WL unfolds over time. PMID:27704695
Larson, James H.; Staples, David F.; Maki, Ryan P.; Vallazza, Jon M.; Knights, Brent C.; Peterson, Kevin E.
2016-01-01
Many ecological processes depend on the regular rise and fall of water levels (WLs), and artificial manipulations to WL regimes can impair important ecosystem services. Previous research has suggested that differences in WL between late summer and early spring may alter the suitability of shoals used by Walleyes Sander vitreus for spawning. Other species, such as the Yellow Perch Perca flavescens, are unlikely to be affected in the same way by WL fluctuations because their spawning requirements are quite different. We used 11–23 years of data from six northern Minnesota lakes to assess the effects of WL fluctuations on the abundances of young-of-the-year (age-0) Walleyes and Yellow Perch. In two lakes (Rainy Lake and Lake Kabetogama), a change in WL management occurred in 2000, after which these lakes saw increased age-0 Walleye abundance, while the other study lakes experienced decreases or no change. Rainy Lake and Lake Kabetogama also had increases in age-0 Yellow Perch, but another study lake did also. We used partial least-squares regression to assess whether WL metrics were associated with variation in age-0 Walleye and Yellow Perch abundances, but WL metrics were seldom associated with age-0 abundance for either species. Our analysis suggested a potential influence of WL regulation on age-0 Walleye abundance, but we found no evidence that early spring access to spawning shoals was the mechanism by which this occurred.
Ensuring excision of intraductal lesions: marker placement at time of ductography.
Woodward, Suzanne; Daly, Caroline P; Patterson, Stephanie K; Joe, Annette I; Helvie, Mark A
2010-11-01
To propose grid coordinate marker placement for patients with suspicious ductogram findings occult on routine workup. To compare the success of marker placement and wire localization (WL) with ductogram-guided WL. A retrospective search of radiology records identified all patients referred for ductography between January 2001 and May 2008. Results for 16 patients referred for ductogram-guided WL and 5 patients with grid coordinate marker placement at the time of ductography and subsequent WL were reviewed. Surgical pathology results and clinical follow-up were reviewed for concordance. Nine of 16 patients (56.3%) underwent successful ductogram-guided WL. Eight of nine patients had papillomas, one of which also had atypical ductal hyperplasia (ADH). One of nine patients had ectatic ducts with inspisated debris. Seven patients who failed ductogram-guided WL eventually underwent open surgical biopsy. Four of seven patients had papillomas, one of which also had lobular carcinoma in situ. Remaining patients had ADH (1/7) and fibrocystic changes with chronic inflammation (3/7). All five (100%) patients with grid coordinate marker placement underwent successful WL and marker excision. Pathology results included three papillomas, papillary intraductal hyperplasia, and fibrocystic change. Grid coordinate marker placement at the time of abnormal ductogram provided an accurate method of localizing ductal abnormalities that are occult on routine workup, thus facilitating future WL. Marker placement obviated the need for repeat ductogram on the day of surgery and ensured surgical removal of the ductogram abnormality. Copyright © 2010 AUR. Published by Elsevier Inc. All rights reserved.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kramer, D.P.; Lewis, E.L.; Armstrong, K.M.
1982-01-01
A commercially available joule-heated glass furnace system is currently being evaluated at Mound as a means of reducing the volume of low-level radioactive waste similar to that found in light water reactor facilities. The furnace utilizes molten soda-lime-silica to initiate and support combustion of the waste feed and to serve as an immobilization matrix. First, corrosion studies were performed to determine the result that various waste loadings of glass would have on the refractory lining the furnace. Second, the chemical durability of soda-lime-silica under various waste loadings was assessed to determine its resistance to leaching under conditions similar to thosemore » encountered at waste disposal sites. Results proved that, although corrosion was quite significant for pure soda-lime-silica and a 10% waste loading, by the time a waste loading of 40% was achieved, the effects of corrosion were virtually nil. The temperature dependence of the corrosion caused by a 0% waste loading of soda-lime-silica on the refractory was also investigated. With an increase in temperature to 2650/sup 0/F, corrosion more than tripled. As a result, incineration and idle temperature is being maintained at, or below, 2400/sup 0/F. In conclusion, from the fact that the higher waste loading of soda-lime glass produced both increased chemical durability and increased refractory life, waste loadings in excess of 40%, and as high as 80%, may be achieved without adverse effect to the glass furnace system or its effectiveness for immobilizing radioactive waste.« less
Andersen, Barbara L.
2009-01-01
Thirty subjects seeking treatment for primary inorgasmia accompanied by sexual anxiety or aversion were assigned to one of three groups: systematic desensitization (SD), directed masturbation (DM), or waiting list control (WL). Following treatment, subjects were retested, and the WL group then received directed masturbation treatment. A third testing constituted a follow-up for the SD and DM groups and a posttreatment testing for the WL. Both treatments were equally effective in improving subjects’ sexual self-acceptance and increasing sexual pleasure. Changes in anxiety were negligible; however, sexual arousal and orgasm for DM and WL subjects increased. The gains of the WL group not only replicated the findings of the DM group but also were of greater magnitude. PMID:6114968
Kao, Tzu-Cheg; Deuster, Patricia A; Burnett, Daniel; Stephens, Mark
2012-05-01
To identify health-related behaviors associated with potentially harmful dietary supplements (DS) - body building (BB), weight loss (WL) and performance enhancing (PE), explore common reasons and sources of information for DS use. Based on the 2005 Survey of 16,146 U.S. military personnel, BB users were dichotomized as yes (regular use - taking any supplement of BB at least once a week in past 12 months) or no; similarly defined for WL and PE. Weighted logistic regression models are used. BB, WL and PE were used by 19.4%, 17.0%, and 8.0% of participants, respectively. Significantly more users were overweight or obese: BMI ≥25 (vs. BMI<25); heavy drinkers (vs. abstainers); and users of taking steroids in their lifetime (vs. not). Most common reasons of BB, WL, and PE users wanted to increase muscle mass, lose weight, and improve physical performance (BB: 45.8%, WL: 54.8%, PE: 38.5%). Fewer than 30% discussed dietary supplements use with their healthcare providers. The leading source of dietary supplements information (BB: 27.8%, WL: 23.6%, PE: 30.0%) was magazines. The dietary supplements: BB, WL and PE were used by significant proportions of service members, and associated with risk-taking behaviors that may affect overall military readiness and public health. Published by Elsevier Inc.
Wang-Landau sampling: Saving CPU time
NASA Astrophysics Data System (ADS)
Ferreira, L. S.; Jorge, L. N.; Leão, S. A.; Caparica, A. A.
2018-04-01
In this work we propose an improvement to the Wang-Landau (WL) method that allows an economy in CPU time of about 60% leading to the same results with the same accuracy. We used the 2D Ising model to show that one can initiate all WL simulations using the outputs of an advanced WL level from a previous simulation. We showed that up to the seventh WL level (f6) the simulations are not biased yet and can proceed to any value that the simulation from the very beginning would reach. As a result the initial WL levels can be simulated just once. It was also observed that the saving in CPU time is larger for larger lattice sizes, exactly where the computational cost is considerable. We carried out high-resolution simulations beginning initially from the first WL level (f0) and another beginning from the eighth WL level (f7) using all the data at the end of the previous level and showed that the results for the critical temperature Tc and the critical static exponents β and γ coincide within the error bars. Finally we applied the same procedure to the 1/2-spin Baxter-Wu model and the economy in CPU time was of about 64%.
Diagnostic criteria for the classification of cancer-associated weight loss.
Martin, Lisa; Senesse, Pierre; Gioulbasanis, Ioannis; Antoun, Sami; Bozzetti, Federico; Deans, Chris; Strasser, Florian; Thoresen, Lene; Jagoe, R Thomas; Chasen, Martin; Lundholm, Kent; Bosaeus, Ingvar; Fearon, Kenneth H; Baracos, Vickie E
2015-01-01
Existing definitions of clinically important weight loss (WL) in patients with cancer are unclear and heterogeneous and do not consider current trends toward obesity. Canadian and European patients with cancer (n = 8,160) formed a population-based data set. Body mass index (BMI) and percent WL (%WL) were recorded, and patients were observed prospectively until death. Data were entered into a multivariable analysis controlling for age, sex, cancer site, stage, and performance status. Relationships for BMI and %WL to overall survival were examined to develop a grading system. Mean overall %WL was -9.7% ± 8.4% and BMI was 24.4 ± 5.1 kg/m(2), and both %WL and BMI independently predicted survival (P < .01). Differences in survival were observed across five categories of BMI (< 20.0, 20.0 to 21.9, 22.0 to 24.9, 25.0 to 27.9, and ≥ 28.0 kg/m(2); P < .001) and five categories of %WL (-2.5% to -5.9%, -6.0% to -10.9%, -11.0% to -14.9%, ≥ -15.0%, and weight stable (± 2.4%); P < .001). A 5 × 5 matrix representing the five %WL categories within each of the five BMI categories was graded based on median survival and prognostic significance. Weight-stable patients with BMI ≥ 25.0 kg/m(2) (grade 0) had the longest survival (20.9 months; 95% CI, 17.9 to 23.9 months), and %WL values associated with lowered categories of BMI were related to shorter survival (P < .001), as follows: grade 1, 14.6 months (95% CI, 12.9 to 16.2 months); grade 2, 10.8 months (95% CI, 9.7 to 11.9 months); grade 3, 7.6 months (95% CI, 7.0 to 8.2 months); and grade 4, 4.3 months (95% CI, 4.1 to 4.6 months). Survival discrimination by grade was observed within specific cancers, stages, ages, and performance status and in an independent validation sample (n = 2,963). A robust grading system incorporating the independent prognostic significance of both BMI and %WL was developed. © 2014 by American Society of Clinical Oncology.
Deden, Laura N; Cooiman, Mellody I; Aarts, Edo O; Janssen, Ignace M C; Gotthardt, Martin; Hendrickx, Baudewijn W; Berends, Frits J
2017-11-01
After Roux-en-Y gastric bypass (RYGB), approximately 10% of patients have insufficient weight loss (excess body mass index loss<50%). Gastric pouch emptying may have a role in weight loss. To compare pouch emptying of patients with poor weight loss and patients with successful weight loss after RYGB. A research-intensive nonacademic hospital and center of expertise in bariatric surgery in the Netherlands METHODS: Female patients were included from among patients with the least (poor weight loss group [P-WL]) and the most weight loss (successful weight loss group [S-WL]) in our center 2 years after RYGB. Pouch emptying scintigraphy was performed after ingestion of a radiolabeled solid meal. Emptying curves, intestinal content (IC) at meal completion and after 15, 30, 45, and 60 minutes, half emptying time, and maximal pouch emptying rate were compared. Five individuals were included in P-WL and 5 in S-WL, on average 2.5 ± .3 years after RYGB. Total weight loss was 18 ± 4.1% in P-WL and 44 ± 5.7% in S-WL (P<.001). In P-WL, a fast initial pouch emptying and exponential emptying curve was observed, compared with a slower initial emptying and more linear curve in S-WL. Faster emptying in P-WL was also shown by a larger IC meal (42 ± 18% versus 4.0 ± 3.3%,), IC 15 (76 ± 15% versus 35 ± 22%), and IC 30 (85 ± 12% versus 54 ± 25%), and a greater maximal pouch emptying rate (17 ± 4.7 versus 5.6 ± 3.4%/min) compared with S-WL (P<.05). A linear correlation was found between total weight loss and maximal pouch emptying rate (Pearson R = .82, P = .004). Pouch emptying for solid food was faster in patients with the least weight loss compared with patients with the most weight loss after RYGB. If pouch emptying is an important mechanism in weight loss, altering the pouch outlet may improve poor weight loss management. Copyright © 2017 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.
Roeland, Eric J; Ma, Joseph D; Nelson, Sandahl H; Seibert, Tyler; Heavey, Sean; Revta, Carolyn; Gallivan, Andrea; Baracos, Vickie E
2017-02-01
Participation in cancer cachexia clinical trials requires a defined weight loss (WL) over time. A loss in skeletal muscle mass, measured by cross-sectional computed tomography (CT) image analysis, represents a possible alternative. Our aim was to compare WL versus muscle loss in patients who were screened to participate in a cancer cachexia clinical trial. This was a single-center, retrospective analysis in metastatic colorectal cancer patients screened for an interventional cancer cachexia trial requiring a ≥5 % WL over the preceding 6 months. Concurrent CT images obtained as part of standard oncology care were analyzed for changes in total muscle and fat (visceral, subcutaneous, and total). Of patients screened (n = 36), 3 (8 %) enrolled in the trial, 17 (47 %) were excluded due to insufficient WL (<5 %), 3 (8 %) were excluded due to excessive WL (>20 %), and 16 (44 %) met inclusion criteria for WL. Patients who met screening criteria for WL (5-20 %) had a mean ± SD of 7.7 ± 8.7 % muscle loss, 24.4 ± 37.5 % visceral adipose loss, 21.6 ± 22.3 % subcutaneous adipose loss, and 22.1 ± 24.7 % total adipose loss. Patients excluded due to insufficient WL had 2 ± 6.4 % muscle loss, but a gain of 8.5 ± 39.8 % visceral adipose, and 4.2 ± 28.2 % subcutaneous adipose loss and 0.8 ± 28.4 % total adipose loss. Of the patients excluded due to WL <5 % (n = 17), 7 (41 %) had a skeletal muscle loss >5 %. Defining cancer cachexia by WL over time may be limited as it does not capture skeletal muscle loss. Cross-sectional CT body composition analysis may improve early detection of muscle loss and patient participation in future cancer cachexia clinical trials.
Falck, Ryan S; Best, John R; Drenowatz, Clemens; Hand, Gregory A; Shook, Robin P; Lavie, Carl J; Blair, Steven N
2018-03-01
The ardent wish to lose weight, drive for thinness (DT), might be 1 psychosocial contributor to weight loss (WL) in adults with overweight and obesity. In examining DT as a predictor of WL, it is important to determine whether its predictive value is equal in males and females and whether it exerts its effects primarily through changes in diet or physical activity (PA). Two-hundred three men and women with overweight and obesity (body mass index >25 kg/m; aged 21-35 years; 47% female) participated in this 12-month observational study. DT score and demographic information were collected at baseline. Participants were measured at quarterly intervals for objectively measured PA, energy intake, and anthropometrics. Linear mixed regression analyses determined whether DT predicted WL over time and whether these effects were moderated by sex. Followup mediation analyses determined whether the effects of DT on WL could be explained by either changes in diet or PA. Females reported higher DT as compared with males at baseline (P < .001). We observed a significant sex × time × DT interaction on WL (P < .04), such that higher DT predicted WL in males (P < .04), but not in females (P = .54). This effect of DT on WL in overweight and obese males was mediated by changes in PA (indirect effect, -0.43; 95% CI, -1.52 to -0.05), but not changes in energy intake. Among young adults with overweight and obesity who have higher DT, PA appears to be more important to WL than caloric restriction, particularly in males.
Ge, Shealinna; Ryan, Alice S
2014-08-01
Zinc-Alpha 2-Glycoprotein (ZAG) has recently been implicated in the regulation of adipose tissue metabolism due to its negative association with obesity and insulin resistance. The purpose of this study is to investigate the relationships between adipose tissue ZAG expression and central obesity, and the effects of six-months of weight loss (WL) or aerobic exercise + weight loss (AEX + WL) on ZAG expression. A six-month, longitudinal study of 33 healthy, overweight or obese postmenopausal women (BMI: 25-46 kg/m(2)) was conducted. Abdominal and gluteal adipose tissue samples were obtained before and after AEX + WL (n = 17) and WL (n = 16). ZAG expression was determined by RT-PCR. Prior to interventions, abdominal ZAG expression was negatively correlated with visceral fat (r = -0.50, P < 0.005), sagittal diameter (r = -0.42, P < 0.05), and positively related to VO(2)max (r = 0.37, P < 0.05). Gluteal ZAG expression was negatively correlated with weight, fat-free mass, visceral fat, resting metabolic rate, and fasting insulin (r = -0.39 to -0.50, all P < 0.05). Abdominal ZAG mRNA levels increased, though not significantly, 5% after AEX + WL and 11% after WL. Gluteal ZAG mRNA levels also did not change significantly with AEX + WL and WL. Abdominal ZAG expression may be important in central fat accumulation and fitness but only modestly increase (nonsignificantly) with weight reduction alone or with aerobic training in obese postmenopausal women. Published by Elsevier Inc.
Blood lead levels and bone turnover with weight reduction in women.
Riedt, Claudia S; Buckley, Brian T; Brolin, Robert E; Ambia-Sobhan, Hasina; Rhoads, George G; Shapses, Sue A
2009-01-01
High bone turnover states are known to raise blood lead levels (BPb). Caloric restriction will increase bone turnover, yet it remains unknown if weight reduction increases BPb due to mobilization of skeletal stores. We measured whole blood Pb levels ((206)Pb) by inductively coupled plasma mass spectrometry in 73 women (age 24-75 years; BMI 23- 61 kg/m(2)) before and after 6 months of severe weight loss (S-WL), moderate weight loss (M-WL), or weight maintenance (WM). Baseline BPb levels were relatively low at 0.2-6.0 microg/dl, and directly associated with age (r=0.49, P<0.0001). After severe WL (-37.4+/-9.3 kg, n=17), BPb increased by 2.1+/-3.9 microg/dl (P<0.05), resulting in BPb levels of 1.3-12.5 microg/dl. M-WL (-5.6+/-2.7 kg, n=39) and WM (0.3+/-1.3 kg, n=17) did not result in an increase in BPb levels (0.5+/-3.2 and 0.0+/-0.7 microg/dl, M-WL and WM, respectively). BPb levels increased more with greater WL (r=0.24, P<0.05). Bone turnover markers increased only with severe WL and were directly correlated with WL. At baseline, higher calcium intake was associated with lower BPb (r=-0.273, P<0.02), however, this association was no longer present after 6 months. Severe weight reduction in obese women increases skeletal bone mobilization and BPb, but values remain well below levels defined as Pb overexposure.
Ge, Shealinna; Ryan, Alice S.
2014-01-01
Objective Zinc-Alpha 2-Glycoprotein (ZAG) has recently been implicated in the regulation of adipose tissue metabolism due to its negative association with obesity and insulin resistance. The purpose of this study is to investigate the relationships between adipose tissue ZAG expression and central obesity, and the effects of six-months of weight loss (WL) or aerobic exercise + weight loss (AEX+WL) on ZAG expression. Design and Methods A six-month, longitudinal study of 33 healthy, overweight or obese postmenopausal women (BMI: 25–46 kg/m2) was conducted. Abdominal and gluteal adipose tissue samples were obtained before and after AEX+WL (n=17) and WL (n=16). ZAG expression was determined by RT-PCR. Results Prior to interventions, abdominal ZAG expression was negatively correlated with visceral fat (r=−0.50, P<0.005), sagittal diameter (r=−0.42, P<0.05), and positively related to VO2max (r=0.37, P<0.05). Gluteal ZAG expression was negatively correlated with weight, fat-free mass, visceral fat, resting metabolic rate, and fasting insulin (r=−0.39 to −0.50, all P<0.05). Abdominal ZAG mRNA levels increased, though not significantly, 5% after AEX+WL and 11% after WL. Gluteal ZAG mRNA levels also did not change significantly with AEX+WL and WL. Conclusions Abdominal ZAG expression may be important in central fat accumulation and fitness that modestly but not significantly increases with weight reduction alone or with aerobic training in obese postmenopausal women. PMID:24929893
Federal Register 2010, 2011, 2012, 2013, 2014
2013-03-29
... DEPARTMENT OF TRANSPORTATION Maritime Administration [Docket No. MARAD-2013 0026] Requested Administrative Waiver of the Coastwise Trade Laws: Vessel W.L. STEWART III; Invitation for Public Comments AGENCY....gov . SUPPLEMENTARY INFORMATION: As described by the applicant the intended service of the vessel W.L...
Caruso, Damiano; Parinella, Ashley H; Schoepf, U Joseph; Stroebel, Maxwell H; Mangold, Stefanie; Wichmann, Julian L; Varga-Szemes, Akos; Ball, B Devon; De Santis, Domenico; Laghi, Andrea; De Cecco, Carlo N
2017-03-01
To determine the optimal window setting for displaying virtual monoenergetic reconstructions of third generation dual-source, dual-energy CT (DECT) angiography of the abdomen. Forty-five patients were evaluated with DECT angiography (90/150 kV, 180/90 ref. mAs). Three datasets were reconstructed: standard linear blending (M_0.6), 70 keV traditional virtual monoenergetic (M70), and 40 keV advanced noise-optimized virtual monoenergetic (M40+). The best window setting (width and level, W/L) was assessed by two blinded observers and was correlated with aortic attenuation to obtain the Optimized W/L setting (O-W/L). Subjective image quality was assessed, and vessel diameters were measured to determine any possible influences between different W/L settings. Repeated measures of variance were used to evaluate comparison of W/L values, image quality, and vessel sizing between M_0.6, M70, and M40+. The Best W/L (B-W/L) for M70 and M40+ was 880/280 and 1410/450, respectively. Results from regression analysis inferred an O-W/L of 850/270 for M70 and 1350/430 for M40+. Significant differences for W and L were found between the Best and the Optimized W/L for M40+, and between M70 and M40+ for both the Best and Optimized W/L. No significant differences for vessel measurements were found using the O-W/L for M40+ compared to the standard M_0.6 (p ≥ 0.16), and significant differences were observed when using the B-W/L with M40+ compared to M_0.6 (p ≤ 0.04). In order to optimize virtual monoenergetic imaging with both traditional M70 and advanced M40+, adjusting the W/L settings is necessary. Our results suggest a W/L setting of 850/270 for M70 and 1350/430 for M40+.
Why do some diabetic patients on the kidney transplant waiting list not receive a transplant?
Kyllönen, Lauri; Salmela, Kaija
2004-10-01
The waiting list (WL) history of 405 diabetic patients placed on the kidney transplantation WL for the years 1993-2000 was examined. By 31 December 2000, 295 (73 %) patients had received a transplant. Of the remaining 110 patients 53 (13 %) were still on the WL; 27 of these were temporarily withdrawn, i.e. non-active, 46 others (11 %) had died and 11 (3 %) had been permanently removed. Patient follow-up continued until the end of 2002. Although the mean total time on the WL of the non-transplanted was twice that of the transplanted patients there were no significant differences in the mean active times on the WL. The mean cumulative withdrawal time of the transplanted and those on the active WL was less than 10 % of their total time on the list, but for the patients who had died or were withdrawn on 31 December 2000 it exceeded 50 %, usually because of diabetic complications. The 5-year survival of the transplanted patients was greatly superior to that of the non-transplanted, as expected. However, the better survival of the transplanted patients is not necessarily proof of a better treatment modality but rather a consequence of the exclusion from transplantation of patients suffering from diabetic complications. It is not justified to compare the survival of transplantable and non-transplantable WL patients.
Observations of a White-light Flare Associated with a Filament Eruption
NASA Astrophysics Data System (ADS)
Song, Y. L.; Guo, Y.; Tian, H.; Zhu, X. S.; Zhang, M.; Zhu, Y. J.
2018-02-01
We present observations of an M5.7 white-light flare (WLF) associated with a small filament eruption in NOAA active region 11476 on 2012 May 10. During this flare, a circular flare ribbon appeared in the east and a remote brightening occurred in the northwest of the active region. Multi-wavelength data are employed to analyze the WLF, including white light (WL), ultraviolet, extreme ultraviolet, hard X-ray (HXR), and microwave. A close spatial and temporal relationship between the WL, HXR, and microwave emissions is found in this WLF. However, the peak time of the WL emission lagged that of the HXR and microwave emissions by about 1–2 minutes. Such a result tends to support the backwarming mechanism for the WL emission. Interestingly, the enhanced WL emission occurred at the two footpoints of the filament. Through forced and potential field extrapolations, we find that the 3D magnetic field in the flare region has a fan-spine feature and that a flux rope lies under the dome-like field structure. We describe the entire process of flare evolution into several steps, each one producing the sequent brightening below the filament, the circular flare ribbons, and the WL enhancement, respectively. We suggest that a reconnection between the magnetic field of the filament and the overlying magnetic field or reconnection within the flux rope leads to the WL enhancement.
METHODS OF ANALYSIS FOR WASTE LOAD ALLOCATION
This research has addressed several unresolved questions concerning the allocation of allowable waste loads among multiple wastewater dischargers within a water quality limited stream segment. First, the traditional assumptions about critical design conditions for waste load allo...
ICPP tank farm closure study. Volume 1
DOE Office of Scientific and Technical Information (OSTI.GOV)
Spaulding, B.C.; Gavalya, R.A.; Dahlmeir, M.M.
1998-02-01
The disposition of INEEL radioactive wastes is now under a Settlement Agreement between the DOE and the State of Idaho. The Settlement Agreement requires that existing liquid sodium bearing waste (SBW), and other liquid waste inventories be treated by December 31, 2012. This agreement also requires that all HLW, including calcined waste, be disposed or made road ready to ship from the INEEL by 2035. Sodium bearing waste (SBW) is produced from decontamination operations and HLW from reprocessing of SNF. SBW and HLW are radioactive and hazardous mixed waste; the radioactive constituents are regulated by DOE and the hazardous constituentsmore » are regulated by the Resource Conservation and Recovery Act (RCRA). Calcined waste, a dry granular material, is produced in the New Waste Calcining Facility (NWCF). Two primary waste tank storage locations exist at the ICPP: Tank Farm Facility (TFF) and the Calcined Solids Storage Facility (CSSF). The TFF has the following underground storage tanks: four 18,400-gallon tanks (WM 100-102, WL 101); four 30,000-gallon tanks (WM 103-106); and eleven 300,000+ gallon tanks. This includes nine 300,000-gallon tanks (WM 182-190) and two 318,000 gallon tanks (WM 180-181). This study analyzes the closure and subsequent use of the eleven 300,000+ gallon tanks. The 18,400 and 30,000-gallon tanks were not included in the work scope and will be closed as a separate activity. This study was conducted to support the HLW Environmental Impact Statement (EIS) waste separations options and addresses closure of the 300,000-gallon liquid waste storage tanks and subsequent tank void uses. A figure provides a diagram estimating how the TFF could be used as part of the separations options. Other possible TFF uses are also discussed in this study.« less
USDA-ARS?s Scientific Manuscript database
Weight loss (WL) induced by energy restriction is highly variable even in controlled clinical trials. An integrative analysis of the plasma metabolome coupled to traditional clinical variables may reveal a WL “responder” phenotype. Therfore, we predicted WL in overweight and obese individuals on a...
USDA-ARS?s Scientific Manuscript database
Weight loss (WL) induced by energy restriction is highly variable even in controlled clinical trials. An integrative analysis of the plasma metabolome coupled to traditional clinical variables may reveal a WL “responder” phenotype. Therfore, we predicted WL in overweight and obese individuals on a...
Marra, James C.; Kim, Dong -Sang
2014-12-18
A number of waste components in US defense high level radioactive wastes (HLW) have proven challenging for current Joule heated ceramic melter (JCHM) operations and have limited the ability to increase waste loadings beyond already realized levels. Many of these ''troublesome'' waste species cause crystallization in the glass melt that can negatively impact product quality or have a deleterious effect on melter processing. Thus, recent efforts at US Department of Energy laboratories have focused on understanding crystallization behavior within HLW glass melts and investigating approaches to mitigate the impacts of crystallization so that increases in waste loading can be realized.more » Advanced glass formulations have been developed to highlight the unique benefits of next-generation melter technologies such as the Cold Crucible Induction Melter (CCIM). Crystal-tolerant HLW glasses have been investigated to allow sparingly soluble components such as chromium to crystallize in the melter but pass out of the melter before accumulating. The Hanford site AZ-101 tank waste composition represents a waste group that is waste loading limited primarily due to high concentrations of Fe 2O 3 (with higher Al 2O 3). Systematic glass formulation development utilizing slightly higher process temperatures and higher tolerance to spinel crystals demonstrated that an increase in waste loading of more than 20% could be achieved for this waste composition, and by extension higher loadings for wastes in the same group.« less
1979-04-11
8217 .,aced -lecture 1.4 -lecture -rating (scale) -written (test) -self-paced -A 4’ --- hands-on -rating (scale) -written (tes . I E -performance -rating ( scall ...a u W. - i it LL SAL~ &K 4 I- >.M Z CL -0 1-. A _jJ 9I.0 N Q~ A.. A4 SIA 0 0 . r &Ca a-A="- JI- " - - -.Z8 -A~ -4 MOSn -r. Z WL~ 4 S. -a Wa. -J W
Rapid PD-L1 detection in tumors with PET using a highly specific peptide
DOE Office of Scientific and Technical Information (OSTI.GOV)
Chatterjee, Samit; Lesniak, Wojciech G.; Miller, Michelle S.
Molecular imaging can report on the status of the tumor immune microenvironment and guide immunotherapeutic strategies to enhance the efficacy of immune modulation therapies. Imaging agents that can rapidly report on targets of immunomodulatory therapies are few. The programmed death ligand 1 (PD-L1) is an immune checkpoint protein over-expressed in several cancers and contributes to tumor immune suppression. Tumor PD-L1 expression is indicative of tumor response to PD-1 and PD-L1 targeted therapies. Herein, we report a highly specific peptide-based positron emission tomography (PET) imaging agent for PD-L1. We assessed the binding modes of the peptide WL12 to PD-L1 by dockingmore » studies, developed a copper-64 labeled WL12 ([{sup 64}Cu]WL12), and performed its evaluation in vitro, and in vivo by PET imaging, biodistribution and blocking studies. Our results show that [{sup 64}Cu]WL12 can be used to detect tumor PD-L1 expression specifically and soon after injection of the radiotracer, to fit within the standard clinical workflow of imaging within 60 min of administration. - Highlights: • A highly specific PD-L1 binding peptide, WL12, was developed as a PET imaging agent. • [{sup 64}Cu]WL12 demonstrates specific binding to PD-L1 in vitro and in vivo. • [{sup 64}Cu]WL12-PET allows PD-L1 detection in cancers within 60 min of administration. • WL12 binding interactions with PD-L1 overlaps with that of PD-1.« less
NASA Astrophysics Data System (ADS)
Xiong, Ming; Davies, Jackie A.; Li, Bo; Yang, Liping; Liu, Ying D.; Xia, Lidong; Harrison, Richard A.; Keiji, Hayashi; Li, Huichao
2017-07-01
Interplanetary corotating interaction regions (CIRs) can be remotely imaged in white light (WL), as demonstrated by the Solar Mass Ejection Imager (SMEI) on board the Coriolis spacecraft and Heliospheric Imagers (HIs) on board the twin Solar TErrestrial RElations Observatory (STEREO) spacecraft. The interplanetary WL intensity, due to Thomson scattering of incident sunlight by free electrons, is jointly determined by the 3D distribution of electron number density and line-of-sight (LOS) weighting factors of the Thomson-scattering geometry. The 2D radiance patterns of CIRs in WL sky maps look very different from different 3D viewpoints. Because of the in-ecliptic locations of both the STEREO and Coriolis spacecraft, the longitudinal dimension of interplanetary CIRs has, up to now, always been integrated in WL imagery. To synthesize the WL radiance patterns of CIRs from an out-of-ecliptic (OOE) vantage point, we perform forward magnetohydrodynamic modeling of the 3D inner heliosphere during Carrington Rotation CR1967 at solar maximum. The mixing effects associated with viewing 3D CIRs are significantly minimized from an OOE viewpoint. Our forward modeling results demonstrate that OOE WL imaging from a latitude greater than 60° can (1) enable the garden-hose spiral morphology of CIRs to be readily resolved, (2) enable multiple coexisting CIRs to be differentiated, and (3) enable the continuous tracing of any interplanetary CIR back toward its coronal source. In particular, an OOE view in WL can reveal where nascent CIRs are formed in the extended corona and how these CIRs develop in interplanetary space. Therefore, a panoramic view from a suite of wide-field WL imagers in a solar polar orbit would be invaluable in unambiguously resolving the large-scale longitudinal structure of CIRs in the 3D inner heliosphere.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Johnson, Jay Dean; Oberkampf, William Louis; Helton, Jon Craig
2004-12-01
Relationships to determine the probability that a weak link (WL)/strong link (SL) safety system will fail to function as intended in a fire environment are investigated. In the systems under study, failure of the WL system before failure of the SL system is intended to render the overall system inoperational and thus prevent the possible occurrence of accidents with potentially serious consequences. Formal developments of the probability that the WL system fails to deactivate the overall system before failure of the SL system (i.e., the probability of loss of assured safety, PLOAS) are presented for several WWSL configurations: (i) onemore » WL, one SL, (ii) multiple WLs, multiple SLs with failure of any SL before any WL constituting failure of the safety system, (iii) multiple WLs, multiple SLs with failure of all SLs before any WL constituting failure of the safety system, and (iv) multiple WLs, multiple SLs and multiple sublinks in each SL with failure of any sublink constituting failure of the associated SL and failure of all SLs before failure of any WL constituting failure of the safety system. The indicated probabilities derive from time-dependent temperatures in the WL/SL system and variability (i.e., aleatory uncertainty) in the temperatures at which the individual components of this system fail and are formally defined as multidimensional integrals. Numerical procedures based on quadrature (i.e., trapezoidal rule, Simpson's rule) and also on Monte Carlo techniques (i.e., simple random sampling, importance sampling) are described and illustrated for the evaluation of these integrals. Example uncertainty and sensitivity analyses for PLOAS involving the representation of uncertainty (i.e., epistemic uncertainty) with probability theory and also with evidence theory are presented.« less
Mazzola, R; Ricchetti, F; Fiorentino, A; Di Paola, G; Fersino, S; Giaj Levra, N; Ruggieri, R; Alongi, F
2016-06-01
Cancer cachexia is a syndrome characterized by weight loss (WL) and sarcopenia. Aim of the study was to assess the impact of cachexia on head and neck changes during definitive cisplatin and image-guided volumetric-modulated arc radiation therapy in a series of locally advanced oropharyngeal cancer. Volume variations of sternocleidomastoid muscle (SCM) were considered as surrogate of muscle changes related to sarcopenia. Two head and neck diameters, encompassing the cranial limits of II and III nodal levels (defined as 'head diameter' and 'neck diameter', respectively), were measured. All parameters were defined retrospectively by means of on-board cone beam computed tomography images at 1-8th to 15-22th and at last fraction (fx) of radiotherapy (RT). Cachexia was defined as WL >5% during treatment. Analysis was conducted correlating the parameter changes with three WL ranges: <5, 5-9 and>10%. Thirty patients were evaluated. One hundred and fifty contoured SCMs and three hundred diameters were collected. Median WL was 6.5% (range, 0-16%). The most significant SCM shrinkage was recorded at 15th fx (mean 1.6 cc) related to WL 5-9% and WL >10% (P 0.001). For 'head diameter', the peak reduction was recorded at the 15th fx (mean 8 mm), statistically correlated to WL >10% (P 0.001). The peak reduction in 'neck diameter' was registered at the 22th fx (mean 6 mm), with a gradual reduction until the end of treatment for WL >5%. In a homogeneous cohort of patients, present study quantified the impact of cachexia on head and neck changes. Present data could provide adaptive RT implications for further investigations.
The Weaker Language in Early Child Bilingualism: Acquiring a First Language as a Second Language?
ERIC Educational Resources Information Center
Meisel, Jurgen M.
2007-01-01
Past research demonstrates that first language (L1)-like competence in each language can be attained in simultaneous acquisition of bilingualism by mere exposure to the target languages. The question is whether this is also true for the "weaker" language (WL). The WL hypothesis claims that the WL differs fundamentally from monolingual L1 and…
Pseudomonas japonica sp. nov., a novel species that assimilates straight chain alkylphenols.
Pungrasmi, Wiboonluk; Lee, Haeng-Seog; Yokota, Akira; Ohta, Akinori
2008-02-01
A bacterial strain, WL(T), which was isolated from an activated sludge, was able to degrade alkylphenols. 16S rDNA sequence analysis indicated that strain WL(T) belonged to the genus Pseudomonas (sensu stricto) and formed a monophyletic clade with the type strain of Pseudomonas graminis and other members in the Pseudomonas putida subcluster with sequence similarity values higher than 97%. Genomic relatedness based on DNA-DNA hybridization of strain WL(T) to these strains is 2-41%. Strain WL(T) contained ubiquinone-9 as the main respiratory quinone, and the G+C content of DNA was 66 mol%. The organism contained hexadecanoic acid (16:0), hexadecenoic acid (16:1) and octadecenoic acid (18:1) as major cellular fatty acids. The hydroxy fatty acids detected were 3-hydroxydecanoic acid (3-OH 10:0), 3-hydroxydodecanoic acid (3-OH 12:0) and 2-hydroxydodecanoic acid (2-OH 12:0). These results, as well as physiological and biochemical characteristics clearly indicate that the strain WL(T) represents a new Pseudomonas species, for which the name Pseudomonas japonica is proposed. The type strain is strain WL(T) (=IAM 15071T=TISTR 1526T).
Naito, Seiji; Algaba, Ferran; Babjuk, Marko; Bryan, Richard T; Sun, Ying-Hao; Valiquette, Luc; de la Rosette, Jean
2016-09-01
White light (WL) is the established imaging modality for transurethral resection of bladder tumour (TURBT). Narrow band imaging (NBI) is a promising addition. To compare 12-mo recurrence rates following TURBT using NBI versus WL guidance. The Clinical Research Office of the Endourological Society (CROES) conducted a prospective randomised single-blind multicentre study. Patients with primary non-muscle-invasive bladder cancer (NMIBC) were randomly assigned 1:1 to TURBT guided by NBI or WL. TURBT for NMIBC using NBI or WL. Twelve-month recurrence rates were compared by chi-square tests and survival analyses. Of the 965 patients enrolled in the study, 481 patients underwent WL-assisted TURBT and 484 patients received NBI-assisted TURBT. Of these, 294 and 303 patients, respectively, completed 12-mo follow-up, with recurrence rates of 27.1% and 25.4%, respectively (p=0.585, intention-to-treat [ITT] analysis). In patients at low risk for disease recurrence, recurrence rates at 12 mo were significantly higher in the WL group compared with the NBI group (27.3% vs 5.6%; p=0.002, ITT analysis). Although TURBT took longer on average with NBI plus WL compared with WL alone (38.1 vs 35.0min, p=0.039, ITT; 39.1 vs 35.7min, p=0.047, per protocol [PP] analysis), lesions were significantly more often visible with NBI than with WL (p=0.033). Frequency and severity of adverse events were similar in both treatment groups. Possible limitations were lack of uniformity of surgical resection, data on smoking status, central pathology review, and specific data regarding adjuvant intravesical instillation therapy. NBI and WL guidance achieved similar overall recurrence rates 12 mo after TURBT in patients with NMIBC. NBI-assisted TURBT significantly reduced the likelihood of disease recurrence in low-risk patients. Use of a narrow band imaging technique might provide greater detection of bladder tumours and subsequent treatment leading to reduced recurrence in low-risk patients. Copyright © 2016 European Association of Urology. Published by Elsevier B.V. All rights reserved.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, Albert A.
2013-07-01
The current estimates and glass formulation efforts have been conservative in terms of achievable waste loadings. These formulations have been specified to ensure that the glasses are homogenous, contain essentially no crystalline phases, are processable in joule-heated, ceramic-lined melters and meet Hanford Tank Waste Treatment and Immobilization Plant (WTP) Contract terms. The WTP's overall mission will require the immobilization of tank waste compositions that are dominated by mixtures of aluminum (Al), chromium (Cr), bismuth (Bi), iron (Fe), phosphorous (P), zirconium (Zr), and sulphur (S) compounds as waste-limiting components. Glass compositions for these waste mixtures have been developed based upon previousmore » experience and current glass property models. Recently, DOE has initiated a testing program to develop and characterize HLW glasses with higher waste loadings and higher throughput efficiencies. Results of this work have demonstrated the feasibility of increases in waste loading from about 25 wt% to 33-50 wt% (based on oxide loading) in the glass depending on the waste stream. In view of the importance of aluminum limited waste streams at Hanford (and also Savannah River), the ability to achieve high waste loadings without adversely impacting melt rates has the potential for enormous cost savings from reductions in canister count and the potential for schedule acceleration. Consequently, the potential return on the investment made in the development of these enhancements is extremely favorable. Glass composition development for one of the latest Hanford HLW projected compositions with sulphate concentrations high enough to limit waste loading have been successfully tested and show tolerance for previously unreported tolerance for sulphate. Though a significant increase in waste loading for high-iron wastes has been achieved, the magnitude of the increase is not as substantial as those achieved for high-aluminum, high-chromium, high-bismuth or sulphur. Waste processing rate increases for high-iron streams as a combined effect of higher waste loadings and higher melt rates resulting from new formulations have been achieved. (author)« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, Albert A.
2013-01-16
The current estimates and glass formulation efforts have been conservative in terms of achievable waste loadings. These formulations have been specified to ensure that the glasses are homogenous, contain essentially no crystalline phases, are processable in joule-heated, ceramic-lined melters and meet Hanford Tank Waste Treatment and Immobilization Plant (WTP) Contract terms. The WTP?s overall mission will require the immobilization of tank waste compositions that are dominated by mixtures of aluminum (Al), chromium (Cr), bismuth (Bi), iron (Fe), phosphorous (P), zirconium (Zr), and sulphur (S) compounds as waste-limiting components. Glass compositions for these waste mixtures have been developed based upon previousmore » experience and current glass property models. Recently, DOE has initiated a testing program to develop and characterize HLW glasses with higher waste loadings and higher throughput efficiencies. Results of this work have demonstrated the feasibility of increases in waste loading from about 25 wt% to 33-50 wt% (based on oxide loading) in the glass depending on the waste stream. In view of the importance of aluminum limited waste streams at Hanford (and also Savannah River), the ability to achieve high waste loadings without adversely impacting melt rates has the potential for enormous cost savings from reductions in canister count and the potential for schedule acceleration. Consequently, the potential return on the investment made in the development of these enhancements is extremely favorable. Glass composition development for one of the latest Hanford HLW projected compositions with sulphate concentrations high enough to limit waste loading have been successfully tested and show tolerance for previously unreported tolerance for sulphate. Though a significant increase in waste loading for high-iron wastes has been achieved, the magnitude of the increase is not as substantial as those achieved for high-aluminum, high-chromium, high-bismuth or sulphur. Waste processing rate increases for high-iron streams as a combined effect of higher waste loadings and higher melt rates resulting from new formulations have been achieved.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Harpenau, Evan M.
2013-10-10
The U.S. Department of Energy (DOE) Oak Ridge Office of Environmental Management (EM-OR) requested that Oak Ridge Associated Universities (ORAU), working under the Oak Ridge Institute for Science and Education (ORISE) contract, provide technical and independent waste management planning support under the American Recovery and Reinvestment Act (ARRA). Specifically, DOE EM-OR requested that ORAU plan and implement a sampling and analysis campaign targeting certain URS|CH2M Oak Ridge, LLC (UCOR) surveillance and maintenance (S&M) process inventory waste. Eight populations of historical and reoccurring S&M waste at the Oak Ridge National Laboratory (ORNL) have been identified in the Waste Handling Plan formore » Surveillance and Maintenance Activities at the Oak Ridge National Laboratory, DOE/OR/01-2565&D2 (WHP) (DOE 2012) for evaluation and processing to determine a final pathway for disposal. Population 7 (POP 7) consists of 56 containers of aged, low-level and potentially mixed S&M waste that has been staged in various locations around ORNL. Several of these POP 7 containers primarily contain personal protective equipment (PPE) and dry active waste (DAW), but may contain other miscellaneous debris. This data sharing report addresses the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) specified waste in a 13-container subpopulation (including eight steel boxes, three 55-gal drums, one sealand, and one intermodal) that lacked sufficient characterization data for possible disposal at the Environmental Management Waste Management Facility (EMWMF) using the approved Waste Lot (WL) 108.1 profile.« less
FIB-NanoSIMS-TEM Coordinated Study of a Wark-Lovering Rim in a Vigarano Type A CAI
NASA Technical Reports Server (NTRS)
Cai, A.; Ito, M.; Keller, L. P.; Ross, D. K.; Nakamura-Messenger, K.
2010-01-01
Wark-Lovering (WL) rims are thin multi layered mineral sequences that surround most Ca, Al-rich inclusions (CAIs). Unaltered WL rims are composed of the same primary high temperature minerals as CAIs, such as melilite, spinel, pyroxene, hibonite, perovskite, anorthite and olivine. It is still unclear whether the rim minerals represent a different generation formed by a separate event from their associated CAIs or are a byproduct of CAI formation. Several models have been proposed for the origins of WL rims including condensation, flashheating, reaction of a CAI with a Mg-Si-rich reservoir (nebular gas or solid); on the basis of mineralogy, abundances of trace elements, O and Mg isotopic studies. Detailed mineralogical characterizations of WL rims at micrometer to nanometer scales have been obtained by TEM observations, but so far no coordinated isotopic - mineralogical studies have been performed. Thus, we have applied an O isotopic imaging technique by NanoSIMS 50L to investigate heterogeneous distributions of O isotopic ratios in minerals within a cross section of a WL rim prepared using a focused ion beam (FIB) instrument. After the isotopic measurements, we determine the detailed mineralogy and microstructure of the same WL FIB section to gain insight into its petrogenesis. Here we present preliminary results from O isotopic and elemental maps by NanoSIMS and mineralogical analysis by FE-SEM of a FIB section of a WL rim in the Vigarano reduced CV3 chondrite.
A FIB/TEM/Nanosims Study of a Wark-Lovering Rim on an Allende CAI
NASA Technical Reports Server (NTRS)
Keller, L. P.; Needham, A. W.; Messenger, S.
2014-01-01
Ca- Al-rich inclusions (CAIs) are commonly surrounded by Wark-Lovering (WL) rims - thin (approx. 50 micrometers) multilayered sequences - whose mineralogy is dominated by high temperature minerals similar to those that occur in the cores of CAIs [1]. The origins of these WL rims involved high temperature events in the early nebula such as condensation, flashheating or reaction with a nebular reservoir, or combinations of these processes. These rims formed after CAI formation but prior to accretion into their parent bodies. We have undertaken a coordinated mineralogical and isotopic study of WL rims to determine the formation conditions of the individual layers and to constrain the isotopic reservoirs they interacted with during their history. We focus here on the spinel layer, the first-formed highest- temperature layer in the WL rim sequence. Results and Discussion: We have performed mineralogical, chemical and isotopic analyses of an unusual ultrarefractory inclusion from the Allende CV3 chondrite (SHAL) consisting of an approx. 500 micrometers long single crystal of hibonite and co-existing coarsegrained perovskite. SHAL is partially surrounded by WL rim. We previously reported on the mineralogy, isotopic compositions and trace elements in SHAL [2-4]. The spinel layer in the WL rim is present only on the hibonite and terminates abruptly at the contact with the coarse perovskite. This simple observation shows that the spinel layer is not a condensate in this case (otherwise spinel would have condensed on the perovskite as well). The spinel layer appears to have formed by gas-phase corrosion of the hibonite by Mg-rich vapors such that the spinel layer grew at the expense of the hibonite. We also found that the spinel layer has the same 16Orich composition as the hibonite. The spinel layer is polycrystalline and individual crystals do not show a crystallographic relationship with the hibonite. An Al-diopside layer overlies the spinel layer, and is present on both the hibonite and perovskite. While the spinel is 16O-rich, WL-rim perovskite and pyroxene are 16O-poor. This isotopic heterogeneity likely reflects O isotopic equilibration of WL-rim perovskite and pyroxene with a planetary O isotopic reservoir after the WL rim formation. The hibonite is zoned and contains wt.% levels of Ti, Mg and Fe in contact with the Fe-bearing spinel (Sp60Hc40) in the WL rim. The Fe enrichment in spinel is likely related to the Na-Fe metasomatism that is ubiquitous in Allende. Conclusions: The petrography and microstructure of the spinel layer in a WL rim sequence shows that it formed by gas phase reactions at high temperature in the nebula. The oxygen isotopic composition of the spinel indicates that this WL rim layer formed in the same (or similar) nebular gas reservoir as the host CAI.
NASA Astrophysics Data System (ADS)
McKisson, R. L.; Grantham, L. F.; Guon, J.; Recht, H. L.
1983-02-01
Results of an estimate of the waste management costs of the commercial high level waste from a 3000 metric ton per year reprocessing plant show that the judicious use of the ceramic waste form can save about $2 billion during a 20 year operating campaign relative to the use of the glass waste form. This assumes PWR fuel is processed and the waste is encapsulated in 0.305-m-diam canisters with ultimate emplacement in a BWIP-type horizontal-borehole repository. Waste loading and waste form density are the driving factors in that the low waste loading (25%) and relatively low density (3.1 g cu cm) characteristic of the glass form require several times as many canisters to handle a given waste throughput than is needed for the ceramic waste form whose waste loading capability exceeds 60% and whose waste density is nominally 5.2 cu cm.
Kuai, Jie; Chen, Yinglong; Wang, Youhua; Meng, Yali; Chen, Binglin; Zhao, Wenqing; Zhou, Zhiguo
2016-01-01
Transient waterlogging occurs frequently in the Yangtze River and adversely affects cotton fiber quality. However, the carbohydrate metabolic mechanism that affects fiber quality after waterlogging remains undescribed. Here, the effects of five waterlogging levels (0, 3, 6, 9, and 12 days) were assessed during flowering and boll formation to characterize the carbohydrates, enzymes and genes that affect the fiber quality of cotton after waterlogging. The cellulose and sucrose contents of cotton fibers were significantly decreased after waterlogging for 6 (WL6), 9 (WL9), and 12 d (WL12), although these properties were unaffected after 3 (WL3) and 6 days at the fruiting branch 14–15 (FB14–15). Sucrose phosphate synthase (SPS) was the most sensitive to waterlogging among the enzymes tested. SPS activity was decreased by waterlogging at FB6–7, whereas it was significantly enhanced under WL3–6 at FB10–15. Waterlogging down-regulated the expression of fiber invertase at 10 days post anthesis (DPA), whereas that of expansin, β-1,4-glucanase and endoxyloglucan transferase (XET) was up-regulated with increasing waterlogging time. Increased mRNA levels and activities of fiber SuSy at each fruiting branch indicated that SuSy was the main enzyme responsible for sucrose degradation because it was markedly induced by waterlogging and was active even when waterlogging was discontinued. We therefore concluded that the reduction in fiber sucrose and down-regulation of invertase at 10 DPA led to a markedly shorter fiber length under conditions WL6–12. Significantly decreased fiber strength at FB6–11 for WL6–12 was the result of the inhibition of cellulose synthesis and the up-regulation of expansin, β-1,4-glucanase and XET, whereas fiber strength increased under WL3–6 at FB14–15 due to the increased cellulose content of the fibers. Most of the indictors tested revealed that WL6 resulted in the best compensatory performance, whereas exposure to waterlogged conditions for more than 6 days led to an irreversible limitation in fiber development. PMID:27446110
Addition of a Worm Leachate as Source of Humic Substances in the Drinking Water of Broiler Chickens
Gomez-Rosales, S.; de L. Angeles, M.
2015-01-01
The objective of this research was to evaluate the growth performance, the apparent ileal digestibility of nitrogen and energy, the retention of nutrients and the apparent metabolizable energy corrected to zero nitrogen retention (AMEn) in broiler chickens supplemented with increasing doses of a worm leachate (WL) as a source of humic substances (HS) in the drinking water. In Exp. 1, 140 male broilers were penned individually and assigned to four WL levels (0%, 10%, 20%, and 30%) mixed in the drinking water from 21 to 49 days of age. Water was offered in plastic bottles tied to the cage. In Exp. 2, 600 male broilers from 21 to 49 days of age housed in floor pens were assigned to three levels of WL (0%, 10%, and 20%) mixed in the drinking water. The WL was mixed with tap water in plastic containers connected by plastic tubing to bell drinkers. The results of both experiments were subjected to analysis of variance and polynomial contrasts. In Exp. 1, the daily water consumption was similar among treatments but the consumption of humic, fulvic, and total humic acids increased linearly (p<0.01) as the WL increased in the drinking water. The feed conversion (p<0.01) and the ileal digestibility of energy, the excretion of dry matter and energy, the retention of dry matter, ash and nitrogen and the AMEn showed quadratic responses (p<0.05) relative to the WL levels in drinking water. In Exp. 2, the increasing level of WL in the drinking water had quadratic effects on the final body weight, daily weight gain and feed conversion ratio (p<0.05). The addition of WL as a source of HS in the drinking water had beneficial effects on the growth performance, ileal digestibility of energy, the retention of nutrients as well on the AMEn in broiler chickens; the best results were observed when the WL was mixed at levels of 20% to 30% in the drinking water. PMID:25557817
Addition of a worm leachate as source of humic substances in the drinking water of broiler chickens.
Gomez-Rosales, S; de L Angeles, M
2015-02-01
The objective of this research was to evaluate the growth performance, the apparent ileal digestibility of nitrogen and energy, the retention of nutrients and the apparent metabolizable energy corrected to zero nitrogen retention (AMEn) in broiler chickens supplemented with increasing doses of a worm leachate (WL) as a source of humic substances (HS) in the drinking water. In Exp. 1, 140 male broilers were penned individually and assigned to four WL levels (0%, 10%, 20%, and 30%) mixed in the drinking water from 21 to 49 days of age. Water was offered in plastic bottles tied to the cage. In Exp. 2, 600 male broilers from 21 to 49 days of age housed in floor pens were assigned to three levels of WL (0%, 10%, and 20%) mixed in the drinking water. The WL was mixed with tap water in plastic containers connected by plastic tubing to bell drinkers. The results of both experiments were subjected to analysis of variance and polynomial contrasts. In Exp. 1, the daily water consumption was similar among treatments but the consumption of humic, fulvic, and total humic acids increased linearly (p<0.01) as the WL increased in the drinking water. The feed conversion (p<0.01) and the ileal digestibility of energy, the excretion of dry matter and energy, the retention of dry matter, ash and nitrogen and the AMEn showed quadratic responses (p<0.05) relative to the WL levels in drinking water. In Exp. 2, the increasing level of WL in the drinking water had quadratic effects on the final body weight, daily weight gain and feed conversion ratio (p<0.05). The addition of WL as a source of HS in the drinking water had beneficial effects on the growth performance, ileal digestibility of energy, the retention of nutrients as well on the AMEn in broiler chickens; the best results were observed when the WL was mixed at levels of 20% to 30% in the drinking water.
Phase II prospective randomized trial of weight loss prior to radical prostatectomy.
Henning, Susanne M; Galet, Colette; Gollapudi, Kiran; Byrd, Joshua B; Liang, Pei; Li, Zhaoping; Grogan, Tristan; Elashoff, David; Magyar, Clara E; Said, Jonathan; Cohen, Pinchas; Aronson, William J
2017-12-04
Obesity is associated with poorly differentiated and advanced prostate cancer and increased mortality. In preclinical models, caloric restriction delays prostate cancer progression and prolongs survival. We sought to determine if weight loss (WL) in men with prostate cancer prior to radical prostatectomy affects tumor apoptosis and proliferation, and if WL effects other metabolic biomarkers. In this Phase II prospective trial, overweight and obese men scheduled for radical prostatectomy were randomized to a 5-8 week WL program consisting of standard structured energy-restricted meal plans (1200-1500 Kcal/day) and physical activity or to a control group. The primary endpoint was apoptotic index in the radical prostatectomy malignant epithelium. Secondary endpoints were proliferation (Ki67) in the radical prostatectomy tissue, body weight, body mass index (BMI), waist to hip ratio, body composition, and serum PSA, insulin, triglyceride, cholesterol, testosterone, estradiol, leptin, adiponectin, interleukin 6, interleukin 8, insulin-like growth factor 1, and IGF binding protein 1. In total 23 patients were randomized to the WL intervention and 21 patients to the control group. Subjects in the intervention group had significantly more weight loss (WL:-3.7 ± 0.5 kg; Control:-1.6 ± 0.5 kg; p = 0.007) than the control group and total fat mass was significantly reduced (WL:-2.1 ± 0.4; Control: 0.1 ± 0.3; p = 0.015). There was no significant difference in apoptotic or proliferation index between the groups. Among the other biomarkers, triglyceride, and insulin levels were significantly decreased in the WL compared with the control group. In summary, this short-term WL program prior to radical prostatectomy resulted in significantly more WL in the intervention vs. the control group and was accompanied by significant reductions in body fat mass, circulating triglycerides, and insulin. However, no significant changes were observed in malignant epithelium apoptosis or proliferation. Future studies should consider a longer term or more intensive weight loss intervention.
Beavers, Kristen M; Ambrosius, Walter T; Rejeski, W Jack; Burdette, Jonathan H; Walkup, Michael P; Sheedy, Jessica L; Nesbit, Beverly A; Gaukstern, Jill E; Nicklas, Barbara J; Marsh, Anthony P
2017-11-01
To examine the long-term effects of exercise modality during weight loss on body composition and associations between body composition and physical function changes. Two hundred forty-nine older adults (66.9 ± 4.7 years, 71% women, 32% African American, BMI: 34.4 ± 3.7 kg/m 2 ) were randomized to weight loss (WL; n = 82), WL plus aerobic training (WL + AT; n = 86), or WL plus resistance training (WL + RT; n = 81) for 18 months. Dual-energy x-ray absorptiometry-acquired body composition, 400-m walk time, and knee extensor strength were measured at baseline and at 6 and 18 months. Total body mass loss was enhanced when WL was combined with exercise (WL: -5.7 ± 0.7 kg, WL + AT: -8.5 ± 0.7 kg, WL + RT: -8.7 ± 0.7 kg; P < 0.01). Total body fat mass loss was significantly greater in WL + AT (-6.8 ± 0.6 kg, -16.4%) and WL + RT (-7.8 ± 0.5 kg, -19.0%) than WL (-4.8 ± 0.6 kg, -10.9%); both P < 0.01. Lean mass loss was greatest in WL + AT (-1.6 ± 0.3 kg, -3.1%) compared with WL + RT (-0.8 ± 0.3 kg, -1.5%) or WL (-1.0 ± 0.3 kg; -2.0%); both P ≤ 0.02. Change in 400-m walk time was associated with change in fat mass (β/SD = +6.1 s; P < 0.01), while change in knee extensor strength was associated with change in lean mass (β/SD = +1.6 Nm; P < 0.01). WL + RT results in less lean mass lost than WL + AT; WL plus exercise yields greater fat mass loss than WL alone. © 2017 The Obesity Society.
NASA Astrophysics Data System (ADS)
Nakatsugawa, M.; Kobayashi, Y.; Okazaki, R.; Taniguchi, Y.
2017-12-01
This research aims to improve accuracy of water level prediction calculations for more effective river management. In August 2016, Hokkaido was visited by four typhoons, whose heavy rainfall caused severe flooding. In the Tokoro river basin of Eastern Hokkaido, the water level (WL) at the Kamikawazoe gauging station, which is at the lower reaches exceeded the design high-water level and the water rose to the highest level on record. To predict such flood conditions and mitigate disaster damage, it is necessary to improve the accuracy of prediction as well as to prolong the lead time (LT) required for disaster mitigation measures such as flood-fighting activities and evacuation actions by residents. There is the need to predict the river water level around the peak stage earlier and more accurately. Previous research dealing with WL prediction had proposed a method in which the WL at the lower reaches is estimated by the correlation with the WL at the upper reaches (hereinafter: "the water level correlation method"). Additionally, a runoff model-based method has been generally used in which the discharge is estimated by giving rainfall prediction data to a runoff model such as a storage function model and then the WL is estimated from that discharge by using a WL discharge rating curve (H-Q curve). In this research, an attempt was made to predict WL by applying the Random Forest (RF) method, which is a machine learning method that can estimate the contribution of explanatory variables. Furthermore, from the practical point of view, we investigated the prediction of WL based on a multiple correlation (MC) method involving factors using explanatory variables with high contribution in the RF method, and we examined the proper selection of explanatory variables and the extension of LT. The following results were found: 1) Based on the RF method tuned up by learning from previous floods, the WL for the abnormal flood case of August 2016 was properly predicted with a lead time of 6 h. 2) Based on the contribution of explanatory variables, factors were selected for the MC method. In this way, plausible prediction results were obtained.
Effect of hypothalamic electrolytic lesions in White Leghorn and broiler male cockerels.
Arnon, E; Snapir, N; Robinzon, B; Heiblum, R
2004-06-01
1. This study compared the effect of bilateral electrolytic lesions of the basomedial hypothalamus (HL) in broiler and White Leghorn (WL) males. 2. Hypothalamic lesions were placed in WL at 10 weeks of age (body weight 1.1 kg) and in broilers, either at 6 weeks (body weight 1.5kg) or at 10 weeks of age (body weight 3.4kg). They were fed ad libitum until autopsy at 16 and 17 weeks of age for broilers and WL, respectively. 3. Hypothalamic lesions caused obesity (high percentage weight of abdominal adipose tissue) in both strains. Obese fowls with unimpaired reproductive systems were classified as OB and those with functional castration as FC (functionally castrated) or FCLC (functionally castrated with large comb). 4. All post-HL syndromes-OB, FC and FCLC-were present in WL, whereas all obese broilers (which are immature at this age) were classified as OB. 5. The percentage weight of abdominal adipose tissue in OB broilers was lower than in OB WL (3% vs 5%, respectively). 6. Daily food intake of OB broilers was higher than control at 12 to 15 weeks of age, regardless of time of placement of HL, whereas daily food intake of OB WL was significantly higher than that of control WL only during the first 2 weeks following HL. 7. Body weight of OB broilers at autopsy was 20% higher than control broilers, whereas body weight of OB WL was not significantly affected. 8. An additional group of broilers was reared to sexual maturity under food restriction until 28 weeks of age. HL were placed at 10 weeks of age (body weight 1.7 kg). Autopsy was performed after a 4-week period of ad libitum feeding. 9. There were OB as well as FC and FCLC among the HL, food-restricted broilers. Percentage weight of testes and spleen were reduced in OB fowls of both strains, but more so in OB WL. 10. Hyperphagia and weight gain were not observed during the ad libitum feeding period of those obese broilers after HL, indicating that hyperphagia and weight gain are secondary to obesity.
Sato, Yasushi; Sagawa, Tamotsu; Hirakawa, Masahiro; Ohnuma, Hiroyuki; Osuga, Takahiro; Okagawa, Yutaka; Tamura, Fumito; Horiguchi, Hiroto; Takada, Kohichi; Hayashi, Tsuyoshi; Sato, Tsutomu; Miyanishi, Koji; Takimoto, Rishu; Kobune, Masayoshi; Kato, Junji
2014-01-01
Background and study aims: The clinical utility of computed virtual chromoendoscopy with flexible spectral imaging color enhancement (FICE) in capsule endoscopy (CE) remains controversial. To clarify the clinical utility of FICE-enhanced CE in evaluating small bowel lesions, we quantitatively assessed white light (WL), FICE, and blue mode (BM) images and examined the sensitivity of these 3 imaging modes of small-bowel lesions from patients who underwent CE. Methods: The CIELAB color difference (∆E) and visual analogue scales (VAS) were measured in 261 CE images (3 different lesion categories) using WL and FICE set 1, 2, and 3, and BM images, respectively. Three endoscopists reviewed CE videos with WL, 3 FICE mode settings, and BM, and compared the sensitivity and detectability for small intestinal diseases from 50 patients who underwent CE. Results: In the assessment of visibility in the 152 vascular lesion images, the ∆E and VAS of FICE set 1, 2, and BM images were significantly higher than that of WL images. In 88 erosion/ulceration images, the ∆E and VAS of FICE set 1 and 2 images were significantly higher than that of WL images. In 21 tumor images, there were no significant differences in ∆E among these modalities. When analyzed on a per-patient basis, FICE settings 1 and 2 had the highest sensitivity (100 %) and specificity (97.3 – 100 %) for vascular lesions. As for erosive/ulcerative lesions, FICE setting 2 had the highest sensitivity (100 %) and specificity (97.2 %). For tumors or polyps, WL had the highest sensitivity (90.9 %) and specificity (87.1 %). In per-lesion analysis, FICE settings 1 and 2 showed significantly superior detection ability over WL for vascular lesions. In the detection of erosive/ulcerative lesions, FICE setting 2 was significantly superior to WL. In tumor images, there was no significant improvement with any of the settings relative to WL images. Conclusions: FICE is most useful for improving CE image quality and detection in cases of angioectasia and erosion/ulceration of the small intestine. PMID:26135265
Paschoal, Marco Aurelio; Santos-Pinto, Lourdes; Lin, Meng; Duarte, Simone
2014-03-01
Investigate the photodynamic antimicrobial effect by the combination of a novel noncoherent broad spectrum visible light and low concentrations of curcumin and toluidine blue over suspensions of Streptococcus mutans. Long illumination times to activate photosensitizers (PS) and the use of high concentrations of these drugs in photodynamic antimicrobial chemotherapy (PACT) are limitations of its application as an antimicrobial technology in dental practice. Planktonic suspensions of S. mutans were standardized and submitted to PACT treatment at low concentrations of curcumin (C) (0.075; 0.75 and 7.5 μM) and toluidine blue (T) (0.25; 2.5 and 25 μM) exposed to 42 J/cm2 (12.2 sec; set power: 3.930 mW) of a white light (WL) (output wavelength range: 400-700 nm; beam diameter: 12 mm) (C+WL+ and T+WL+, PACT groups; incubation time, C: 60 sec; T: 5 min); isolated effect of both C (C+WL-) and T concentrations (T+WL-); effect of light source (C-WL+ and T-WL+) and suspensions neither submitted to PS nor to light-emitting diode (LED) illumination (control groups, C-WL- and T-WL-). Aliquots of each group were diluted and cultured on blood agar plates and the number of colony-forming units (CFU)/mL was recorded, transformed into log10 and analyzed by ANOVA and Tukey's test at a cutoff value at 0.05. The groups submitted to PACT presented a bacterial reduction value of>5-log10 to both tested PS in comparison with control groups (p<0.05). PS or light source used alone demonstrated no antimicrobial effect on the number of viable bacterial counts. The combination of a novel noncoherent light at short illumination exposure time with low concentrations of studied PS achieved a lethal photoinactivation of S. mutans, and can be considered an effective antimicrobial in vitro approach for reducing the number of micro-organisms involved with the dental caries process.
Glass Ceramic Waste Forms for Combined CS+LN+TM Fission Products Waste Streams
DOE Office of Scientific and Technical Information (OSTI.GOV)
Crum, Jarrod V.; Turo, Laura A.; Riley, Brian J.
2010-09-23
In this study, glass ceramics were explored as an alternative waste form for glass, the current baseline, to be used for immobilizing alkaline/alkaline earth + lanthanide (CS+LN) or CS+LN+transition metal (TM) fission-product waste streams generated by a uranium extraction (UREX+) aqueous separations type process. Results from past work on a glass waste form for the combined CS+LN waste streams showed that as waste loading increased, large fractions of crystalline phases precipitated upon slow cooling.[1] The crystalline phases had no noticeable impact on the waste form performance by the 7-day product consistency test (PCT). These results point towards the development ofmore » a glass ceramic waste form for treating CS+LN or CS+LN+TM combined waste streams. Three main benefits for exploring glass ceramics are: (1) Glass ceramics offer increased solubility of troublesome components in crystalline phases as compared to glass, leading to increased waste loading; (2) The crystalline network formed in the glass ceramic results in higher heat tolerance than glass; and (3) These glass ceramics are designed to be processed by the same melter technology as the current baseline glass waste form. It will only require adding controlled canister cooling for crystallization into a glass ceramic waste form. Highly annealed waste form (essentially crack free) with up to 50X lower surface area than a typical High-Level Waste (HLW) glass canister. Lower surface area translates directly into increased durability. This was the first full year of exploring glass ceramics for the Option 1 and 2 combined waste stream options. This work has shown that dramatic increases in waste loading are achievable by designing a glass ceramic waste form as an alternative to glass. Table S1 shows the upper limits for heat, waste loading (based on solubility), and the decay time needed before treatment can occur for glass and glass ceramic waste forms. The improvements are significant for both combined waste stream options in terms of waste loading and/or decay time required before treatment. For Option 1, glass ceramics show an increase in waste loading of 15 mass % and reduction in decay time of 24 years. Decay times of {approx}50 years or longer are close to the expected age of the fuel that will be reprocessed when the modified open or closed fuel cycle is expected to be put into action. Option 2 shows a 2x to 2.5x increase in waste loading with decay times of only 45 years. Note that for Option 2 glass, the required decay time before treatment is only 35 years because of the waste loading limits related to the solubility of MoO{sub 3} in glass. If glass was evaluated for similar waste loadings as those achieved in Option 2 glass ceramics, the decay time would be significantly longer than 45 years. These glass ceramics are not optimized, but already they show the potential to dramatically reduce the amount of waste generated while still utilizing the proven processing technology used for glass production.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Marra, James; Kim, Dong -Sang; Maio, Vincent
A number of waste components in US defense high level radioactive wastes (HLW) have proven challenging for current Joule heated ceramic melter (JHCM) operations and have limited the ability to increase waste loadings beyond already realized levels. Many of these “troublesome" waste species cause crystallization in the glass melt that can negatively impact product quality or have a deleterious effect on melter processing. Recent efforts at US Department of Energy laboratories have focused on understanding crystallization behavior within HLW glass melts and investigating approaches to mitigate the impacts of crystallization so that increases in waste loading can be realized. Advancedmore » glass formulations have been developed to highlight the unique benefits of next-generation melter technologies such as the Cold Crucible Induction Melter (CCIM). Crystal-tolerant HLW glasses have been investigated to allow sparingly soluble components such as chromium to crystallize in the melter but pass out of the melter before accumulating.The Hanford site AZ-101 tank waste composition represents a waste group that is waste loading limited primarily due to high concentrations of Fe 2O 3 (also with high Al 2O 3 concentrations). Systematic glass formulation development utilizing slightly higher process temperatures and higher tolerance to spinel crystals demonstrated that an increase in waste loading of more than 20% could be achieved for this waste composition, and by extension higher loadings for wastes in the same group. An extended duration CCIM melter test was conducted on an AZ-101 waste simulant using the CCIM platform at the Idaho National Laboratory (INL). The melter was continually operated for approximately 80 hours demonstrating that the AZ-101 high waste loading glass composition could be readily processed using the CCIM technology. The resulting glass was close to the targeted composition and exhibited excellent durability in both the as poured state and after being slowly cooled according to the canister centerline cooling (CCC) profile. Glass formulation development was also completed on other Hanford tank wastes that were identified to further challenge waste loading due to the presence of appreciable quantities (>750 g) of plutonium in the waste tanks. In addition to containing appreciable Pu quantities, the C-102 waste tank and the 244-TX waste tank contain high concentrations of aluminum and iron, respectively that will further challenge vitrification processing. Glass formulation testing also demonstrated that high waste loadings could be achieved with these tank compositions using the attributes afforded by the CCIM technology.« less
[Effects of salt and waterlogging stress at post-anthesis stage on wheat grain yield and quality].
Zheng, Chun-Fang; Jiang, Dong; Dai, Ting-Bo; Jing, Qi; Cao, Wei-Xing
2009-10-01
A pot experiment was conducted to study the effects of salt (ST), waterlogging (WL), and their combination (SW) at post-anthesis on the grain yield and its starch and protein components of wheat cultivars Yangmai 12 and Huaimai 17. Comparing with the control, treatments ST, WL, and SW, especially ST and SW, decreased the allocation of nitrogen and carbon assimilates at pre- and post-anthesis to the grains significantly, resulting in an obvious decrease of grain yield and its protein and starch contents. Both ST and SW had significant negative effects on the glutenin/gliadin and amylase/amylopectin ratios in the grains, compared to CK and WL. Yangmai 12 was more sensitive to ST than SW, while Huaimai 17 was in adverse. WL decreased the accumulation of protein and starch in the grains of the two cultivars. Except that the glutenin and albumin in Huaimai 17 had some increase, the globulin and gliadin in Huaimai 17 and all protein components in Yangmai 12 were decreased under WL.
Crustal structure and evolution of the Mawson Sea, western Wilkes Land margin, East Antarctica
Leitchenkov, G.L.; Gandyukhin, V.V.; Guseva, Yu. B.; Kazankov, A. Yu
2007-01-01
3 to 11 mm/yr. Three major unconformities are identified in the sedimentary cover of the Mawson Sea and are interpreted to be caused by break-up between Australia and Antarctica at about 81 Ma ago (WL1), the first arrival of the ice sheet to the Mawson Sea (WL3) and continental scale glaciation at about 34 Ma ago (WL4).
Effect of canal length and curvature on working length alteration with WaveOne reciprocating files.
Berutti, Elio; Chiandussi, Giorgio; Paolino, Davide Salvatore; Scotti, Nicola; Cantatore, Giuseppe; Castellucci, Arnaldo; Pasqualini, Damiano
2011-12-01
This study evaluated the working length (WL) modification after instrumentation with WaveOne Primary (Dentsply Maillefer, Ballaigues, Switzerland) reciprocating files and the incidence of overinstrumentation in relation to the initial WL. Thirty-two root canals of permanent teeth were used. The angles of curvature of the canals were calculated on digital radiographs. The initial WL with K-files was transferred to the matched WaveOne Primary reciprocating files. After glide paths were established with PathFile (Dentsply Maillefer, Ballaigues, Switzerland), canals were shaped with WaveOne Primary referring to the initial WL. The difference between the postinstrumentation canal length and the initial canal length was analyzed by using a fiberoptic inspection microscope. Data were analyzed with a balanced 2-way factorial analysis of variance (P < .05). Referring to the initial WL, 24 of 32 WaveOne Primary files projected beyond the experimental apical foramen (minimum-maximum, 0.14-0.76 mm). A significant decrease in the canal length after instrumentation (95% confidence interval ranging from -0.34 mm to -0.26 mm) was detected. The canal curvature significantly influenced the WL variation (F(1) = 30.65, P < .001). The interaction between the initial canal length and the canal curvature was statistically significant (F(2) = 4.38, P = .014). Checking the WL before preparation of the apical third of the root canal is recommended when using the new WaveOne NiTi single-file system. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.
Hirokawa, Mitsuyoshi; Nishihara, Eijun; Takada, Nami; Higuchi, Miyoko; Kotakemori, Masumi; Hayashi, Toshitetsu; Miyauchi, Akira
2018-02-26
Hashimoto's thyroiditis with heavy lymphoplasmacytic infiltration is a common comorbidity of immunoglobulin G4 (IgG4)-related thyroiditis and Warthin-like papillary thyroid carcinoma (WL-PTC). We hypothesized that WL-PTC may have a strong association with IgG4-related thyroiditis. To validate this hypothesis, we clinically and immunohistochemically studied 17 WL-PTC cases. Fourteen patients (82.4%) had anti-thyroglobulin antibody and were confirmed to have Hashimoto's thyroiditis through microscopic analysis. Among them, five (29.4%) had disease consistent with IgG4-related thyroiditis but did not exhibit a "storiform" pattern or obliterative phlebitis. IgG4-related diseases were not found in other organs. No cases with serum IgG4 level of >135 mg/dL were noted. A total of 94.1% of WL-PTC cases had IgG4-positive plasma cells ( + PCs) in the stroma, and cases with rich IgG4 + PCs were more frequently associated with Hashimoto's thyroiditis than those with poor IgG4 + PCs. In this study, all three cases without Hashimoto's thyroiditis had poor IgG4 + PCs, and one of them did not exhibit IgG4 + PCs in the stroma of WL-PTC and Hashimoto's thyroiditis. Nodal metastatic lesions were seen in eight cases, all of which were not WL-PTC. As such, we should consider that the Hashimoto's disease with rich IgG4 + PCs seen in our cases is representative of non-IgG4-related disease and not IgG4-related disease involving multiple organs. This study is the first to demonstrate the presence of IgG4 + PCs in the stroma of WL-PTC. We concluded that the appearance of IgG4 + PCs in the stroma of WL-PTC may be related to Hashimoto's thyroiditis with rich IgG4 + PC.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Xiong, Ming; Yang, Liping; Liu, Ying D.
Interplanetary corotating interaction regions (CIRs) can be remotely imaged in white light (WL), as demonstrated by the Solar Mass Ejection Imager (SMEI) on board the Coriolis spacecraft and Heliospheric Imagers (HIs) on board the twin Solar TErrestrial RElations Observatory ( STEREO ) spacecraft. The interplanetary WL intensity, due to Thomson scattering of incident sunlight by free electrons, is jointly determined by the 3D distribution of electron number density and line-of-sight (LOS) weighting factors of the Thomson-scattering geometry. The 2D radiance patterns of CIRs in WL sky maps look very different from different 3D viewpoints. Because of the in-ecliptic locations ofmore » both the STEREO and Coriolis spacecraft, the longitudinal dimension of interplanetary CIRs has, up to now, always been integrated in WL imagery. To synthesize the WL radiance patterns of CIRs from an out-of-ecliptic (OOE) vantage point, we perform forward magnetohydrodynamic modeling of the 3D inner heliosphere during Carrington Rotation CR1967 at solar maximum. The mixing effects associated with viewing 3D CIRs are significantly minimized from an OOE viewpoint. Our forward modeling results demonstrate that OOE WL imaging from a latitude greater than 60° can (1) enable the garden-hose spiral morphology of CIRs to be readily resolved, (2) enable multiple coexisting CIRs to be differentiated, and (3) enable the continuous tracing of any interplanetary CIR back toward its coronal source. In particular, an OOE view in WL can reveal where nascent CIRs are formed in the extended corona and how these CIRs develop in interplanetary space. Therefore, a panoramic view from a suite of wide-field WL imagers in a solar polar orbit would be invaluable in unambiguously resolving the large-scale longitudinal structure of CIRs in the 3D inner heliosphere.« less
Paolini, Brielle M; Laurienti, Paul J; Simpson, Sean L; Burdette, Jonathan H; Lyday, Robert G; Rejeski, W Jack
2015-01-01
Obesity is a public health crisis in North America. While lifestyle interventions for weight loss (WL) remain popular, the rate of success is highly variable. Clearly, self-regulation of eating behavior is a challenge and patterns of activity across the brain may be an important determinant of success. The current study prospectively examined whether integration across the Hot-State Brain Network of Appetite (HBN-A) predicts WL after 6-months of treatment in older adults. Our metric for network integration was global efficiency (GE). The present work is a sub-study (n = 56) of an ongoing randomized clinical trial involving WL. Imaging involved a baseline food-cue visualization functional MRI (fMRI) scan following an overnight fast. Using graph theory to build functional brain networks, we demonstrated that regions of the HBN-A (insula, anterior cingulate cortex (ACC), superior temporal pole (STP), amygdala and the parahippocampal gyrus) were highly integrated as evidenced by the results of a principal component analysis (PCA). After accounting for known correlates of WL (baseline weight, age, sex, and self-regulatory efficacy) and treatment condition, which together contributed 36.9% of the variance in WL, greater GE in the HBN-A was associated with an additional 19% of the variance. The ACC of the HBN-A was the primary driver of this effect, accounting for 14.5% of the variance in WL when entered in a stepwise regression following the covariates, p = 0.0001. The HBN-A is comprised of limbic regions important in the processing of emotions and visceral sensations and the ACC is key for translating such processing into behavioral consequences. The improved integration of these regions may enhance awareness of body and emotional states leading to more successful self-regulation and to greater WL. This is the first study among older adults to prospectively demonstrate that, following an overnight fast, GE of the HBN-A during a food visualization task is predictive of WL.
Topkan, Erkan; Parlak, Cem; Selek, Ugur
2013-11-15
We retrospectively investigated the impact of weight change (WC) during concurrent chemoradiation therapy (C-CRT) on clinical outcomes of stage 3B non-small cell lung cancer (NSCLC) patients. A total of 425 patients treated with C-CRT were included. All patients received 60 to 66 Gy of thoracic radiation therapy concurrently with 1 to 3 cycles of platinum-based chemotherapy. Pre- and posttreatment weight measurements on first and last days of C-CRT were used for WC. Patients were divided into 2 groups: group 1=weight loss (WL); group 2=weight preservation/gain (WP) for comparative analyses. Following C-CRT, 252 patients (59.3%) experienced WL, while 89 patients (20.9%) and 84 patients (19.8%) showed WP or WG. At median 24.2 months of follow-up, 142 patients (33.4%) were alive (84 WP [48.6%] and 58 WL [23.0%]), and 58 (13.6%) of them were free of disease progression (41 [23.7%] for WP and 17 [6.7%] for WL). Median overall survival (OS), locoregional progression-free survival (LRPFS), progression-free survival (PFS), and distant metastases-free survival (DMFS) for the entire population were 22.8, 14.4, 10.6, and 11.7 months, respectively. Intergroup comparisons between WP and WL cohorts revealed significantly superior OS, LRPFS, PFS, and DMFS in WP patients (P<.05 for each). On multivariate analyses, only WL and advanced T stage were associated with poor prognosis (P<.05). Present results in 425 stage 3B NSCLC patients demonstrated that WL during C-CRT is strongly associated with inferior survival outcomes compared to WP. This emerging finding might be useful by forming an encouraging basis for future investigations in facilitating a way to improve the outcomes of these patients experiencing WL during C-CRT. Copyright © 2013 Elsevier Inc. All rights reserved.
Moderate weight loss in obese and overweight men preserves bone quality12345
Pop, L Claudia; Sukumar, Deeptha; Tomaino, Katherine; Schlussel, Yvette; Schneider, Stephen H; Gordon, Chris L; Wang, Xiangbing; Shapses, Sue A
2015-01-01
Background: Weight loss (WL) negatively affects bone mineral density (BMD) in older populations and has specifically been shown in women. Objective: In this prospective controlled trial, we examined variables of bone quality and endocrine changes after intentional WL in men. Design: Thirty-eight overweight and obese [mean ± SD body mass index (in kg/m2): 31.9 ± 4.4; age: 58 ± 6 y] men were recruited to either WL through caloric restriction or weight maintenance (WM) for 6 mo. Results: There was a −7.9 ± 4.4% and +0.2 ± 1.6% change in body weight in the WL and WM groups, respectively. There was a greater increase in femoral neck and total body BMD and bone mineral content (BMC) in the WM group than in the WL group (P-interaction effect < 0.05). In contrast, there was a trend for the tibia cortical thickness and area to decrease more in the WM group than in the WL group (P ≤ 0.08). There was a decrease in the periosteal circumference in both groups over time (P < 0.01) and no statistically significant changes in trabecular bone. Circulating total, free, and bioavailable estradiol decreased in the WL group compared with the WM group, and changes were different between groups (P < 0.05). Serum total and bioavailable testosterone increased in both groups (P < 0.01). Serum 25-hydroxyvitamin D increased to a similar extent in both groups (P < 0.05). Conclusions: Moderate WL in overweight and obese men did not decrease BMD at any anatomical site or alter cortical and trabecular bone and geometry. Also, despite increased BMD at some sites when maintaining excess body weight, cortical bone showed a trend in the opposite direction. This trial was registered at clinicaltrials.gov as NCT00472745. PMID:25733651
Aboumarzouk, Omar M; Mains, Edward; Moseley, Harry; Kata, Sławomir G
2013-05-01
We aimed to assess the diagnostic accuracy of photodynamic diagnostic ureterorenoscopy (PDD-FURS) in detection of UUT-TCC in comparison with CT Urogram (CTU) and WL-FURS. Between June 2009 and August 2011, 30 patients underwent PDD-FURS after CTU for suspicion of UUT-TCC. Ureterorenoscopy was performed for abnormal upper urinary tract on imaging. Oral 5-Aminolevulinic Acid (5-ALA) was used as a photosensitizer. All procedures were performed by single endourologist experienced in photodynamic diagnosis. The sensitivity, specificity, and detection rate of WL-FURS, PDD-FURS and CTU were calculated using the Meta-DiSc v1.4 programme. P values <0.05 were considered significant. PDD-FURS detected more UUT-TCCs than CTU or WL-FURS (94% (16/17) vs. 76.5% (13/17) vs. 82% (14/17) respectively). PDD-FURS was not significantly more sensitive than CTU and WL-FURS to detect UUT-TCC (0.94 (95% CI: 0.71-0.99) vs. 0.82 (95% CI: 0.57-0.96) vs. 0.81 (95% CI: 0.54-0.96) respectively; PDD-FURS vs. CTU: P=0.249; PDD-FURS vs. WL-FURS: P=0.277). There was no difference in the specificity between PDD-FURS and WL-FURS (1.0 (95% CI: 0.75-1.0) and 1.0 (95% CI: 0.75-1.0) respectively) (P=1), while PDD-FURS was significantly more specific than CTU (CTU: 0.21 (95% CI: 0.05-0.51) (P<0.001). PDD-FURS picked up 3 cases of CIS, which was not seen on WL-FURL and CTU. Oral 5-ALA induced PDD-FURS has a high sensitivity and specificity to detect lesions and a higher detection rate to diagnose UUT-TCC than WL-FURS and CTU. It appears to be the only tool to visualise UUT CIS lesions. Copyright © 2012 Elsevier B.V. All rights reserved.
Miller, G D
2010-06-01
Physicians are often reluctant to advise older obese patients to lose weight for fear of compromised nutrition and excessive loss of muscle mass and strength, all of which may lead to a loss of independence and accelerate disability. Therefore, the purpose of this study was to examine nutrient intake in older obese adults undergoing a weight loss intervention. The study setting was at a university research facility. A total of 71 participants (age, 69.5 (SD = 5.8) yrs; 62% female; BMI, 34.6 (4.4) kg/m2) were recruited. Individuals were randomized into either a weight stable (WS) control group or an intensive weight loss (WL) group. The WL intervention was for 6 months and utilized partial meal replacements (PMR) and a facility-based 3 d/wk, 60 min/session exercise training program encompassing both aerobic and strength exercises. Weight loss goal for WL was 10% from baseline at 6-months. Variables were obtained at baseline and 6-months and included 3 day dietary records along with daily step counts for 7 days. Total energy, macronutrients (g and % of energy), micronutrients (vitamins and minerals), as well as use of PMR were assessed from the diet records. Body mass and body fat (g and % of body mass) were determined at the 2 time points. Estimated marginal means (SEM) for weight loss at 6-months was -8.8 (0.7)% for WL and -0.1 (0.7)% for WS. Daily energy intake at 6-months was lower for WL (1396 (64) kcals) compared to WS (1817 (71) kcals). Additionally, those in the WL group (compared to WS) had lower intakes of total fat (27.5 (1.2)%, WL vs. 36.1 (4.6)%, WS) and saturated fatty acids (8.5 (0.4)% vs. 10.8 (0.5)%), and had higher levels of carbohydrates (57.6 (1.5)% vs. 49.0 (1.7)%), protein (18.4 (0.5% vs. 16.2 (0.6)%), and dietary fiber (21.0 (0.9) g vs. 17.4 (1.0) g) at 6-months. Even with reduced total calorie intake, key micronutrients (calcium, iron, vitamin D, vitamin E, vitamin C) were higher for WL vs. WS at 6-months. Total daily step counts were higher for WL vs. WS at 6-months. A nutrition intervention to promote weight loss in older obese adults was achieved using PMR as a primary strategy. Diet quality was improved for WL vs. WS in using the nutrient fortified product, even with a reduction in total energy intake.
Cenozoic ice sheet history from East Antarctic Wilkes Land continental margin sediments
Escutia, C.; De Santis, L.; Donda, F.; Dunbar, R.B.; Cooper, A. K.; Brancolini, Giuliano; Eittreim, S.L.
2005-01-01
The long-term history of glaciation along the East Antarctic Wilkes Land margin, from the time of the first arrival of the ice sheet to the margin, through the significant periods of Cenozoic climate change is inferred using an integrated geophysical and geological approach. We postulate that the first arrival of the ice sheet to the Wilkes Land margin resulted in the development of a large unconformity (WL-U3) between 33.42 and 30 Ma during the early Oligocene cooling climate trend. Above WL-U3, substantial margin progradation takes place with early glacial strata (e.g., outwash deposits) deposited as low-angle prograding foresets by temperate glaciers. The change in geometry of the prograding wedge across unconformity WL-U8 is interpreted to represent the transition, at the end of the middle Miocene "climatic optimum" (14-10 Ma), from a subpolar regime with dynamic ice sheets (i.e., ice sheets come and go) to a regime with persistent but oscillatory ice sheets. The steep foresets above WL-U8 likely consist of ice proximal sediments (i.e., water-lain till and debris flows) deposited when grounded ice-sheets extended into the shelf. On the continental rise, shelf progradation above WL-U3 results in an up-section increase in the energy of the depositional environment (i.e., seismic facies indicative of more proximal turbidite and of bottom contour current deposition from the deposition of the lower WL-S5 sequence to WL-S7). Maximum rates of sediment delivery to the rise occur during the development of sequences WL-S6 and WL-S7, which we infer to be of middle Miocene age. During deposition of the two uppermost sequences, WL-S8 and WL-S9, there is a marked decrease in the sediment supply to the lower continental rise and a shift in the depocenters to more proximal areas of the margin. We believe WL-S8 records sedimentation during the final transition from a dynamic to a persistent but oscillatory ice sheet in this margin (14-10 Ma). Sequence WL-S9 forms under a polar regime during the Pliocene-Pleistocene, when most sediment delivered to the margin is trapped in the outer shelf and slope-forming steep prograding wedges. During the warmer but still polar, Holocene, biogenic sediment accumulates quickly in deep inner-shelf basins during the high-stand intervals. These sediments contain an ultrahigh resolution (annual to millennial) record of climate variability. Validation of our inferences about the nature and timing of Wilkes Land glacial sequences can be achieved by deep sampling (i.e., using IODP-type techniques). The most complete record of the long-term history of glaciation in this margin can be obtained by sampling both (1) the shelf, which contains the direct (presence or no presence of ice) but low-resolution record of glaciation, and (2) the rise, which contains the distal (cold vs. warm) but more complete record of glaciation. The Wilkes Land margin is the only known Antarctic margin where the presumed "onset" of glaciation unconformity (WL-U3) can be traced from shelf to the abyssal plain, allowing links between the proximal and the distal records of glaciation to be established. Additionally, the eastern segment of the Wilkes Land margin may be more sensitive to climate change because the East Antarctic Ice Sheet (EAIS) is grounded below sea level. Therefore, the Wilkes Land margin is not only an ideal location to obtain the long-term EAIS history but also to obtain the shorter-term record of ice sheet fluctuations at times that the East Antarctic Ice Sheet is thought to have been more stable (after 15 Ma-recent). ?? 2004 Elsevier B.V. All rights reserved.
Minimum Information Dominating Set for Critical Sampling over Graphs
2015-04-01
NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) University of...not have identical VOSPs under µWl and µ W l′ . We insert D(µWl , µ W l′ ) ∪ (∪ k′ t=1D(µ Vit jt |µWl , µ Vit j′ t |µWl′ )) in- to E for every jt, j′t
LEATHER TANNERY WASTE MANAGEMENT THROUGH PROCESS CHANGE, REUSE AND PRETREATMENT
Reduction of tannery waste, i.e., trivalent chromium, sulfide and oil and grease components has been accomplished by process change. Protein recovery and hydroclonic separation of solids was shown to be possible in tannery processing in reducing waste loading. All waste load redu...
Laser-Based Fuel Cell Manufacturing for Thermal Management
2005-10-12
r IMITA T O 6 1 i I1 .114 141-" n. 14 F . I #1 l i f II 0I0 1(P ,1 L P ER I II I U-ABSTRACT- ------- U inr I L nEron ; . A , wl "t . Tills rAI Ou 1 0...concentration is too low to form a connecting network of conductive sites. On the other hand, the material undergoes a sharp transition from...carbon black loading due to the development of a network of closely-seated CB particles. The predicted very high electrical resistivity for 1 and 2 Vol
High solids co-digestion of food and landscape waste and the potential for ammonia toxicity
DOE Office of Scientific and Technical Information (OSTI.GOV)
Drennan, Margaret F.; DiStefano, Thomas D., E-mail: thomas.distefano@bucknell.edu
Highlights: • We evaluated co-digestion of food and landscape waste with a pilot-scale anaerobic dry digester. • We evaluated reactor performance at 35 °C under low and high organic loading rates. • Performance was stable under low organic loading rate, but declined under high organic loading rate. • Respirometry was employed to investigate potential inhibition due to ammonia. • Landscape waste was unsuitable in increasing the C:N ratio during codigestion. - Abstract: A pilot-scale study was completed to determine the feasibility of high-solids anaerobic digestion (HSAD) of a mixture of food and landscape wastes at a university in central Pennsylvaniamore » (USA). HSAD was stable at low loadings (2 g COD/L-day), but developed inhibitory ammonia concentrations at high loadings (15 g COD/L-day). At low loadings, methane yields were 232 L CH{sub 4}/kg COD fed and 229 L CH{sub 4}/kg VS fed, and at high loadings yields were 211 L CH{sub 4}/kg COD fed and 272 L CH{sub 4}/kg VS fed. Based on characterization and biodegradability studies, food waste appears to be a good candidate for HSAD at low organic loading rates; however, the development of ammonia inhibition at high loading rates suggests that the C:N ratio is too low for use as a single substrate. The relatively low biodegradability of landscape waste as reported herein made it an unsuitable substrate to increase the C:N ratio. Codigestion of food waste with a substrate high in bioavailable carbon is recommended to increase the C:N ratio sufficiently to allow HSAD at loading rates of 15 g COD/L-day.« less
Regnault, Nolwenn; Botton, Jérémie; Blanc, Laurence; Hankard, Régis; Forhan, Anne; Goua, Valérie; Thiebaugeorges, Olivier; Kaminski, Monique; Heude, Barbara; Charles, Marie-Aline
2011-05-01
We aimed to study the determinants of neonatal weight loss measured on the third day of life in term-infants. The EDEN mother-child cohort is a prospective study that recruited 2002 pregnant women before 24 weeks of gestation in two French university hospitals. Neonates were weighed every day until discharge that occurred on average 4.5 days after birth. Altogether, 1557 healthy term neonates with data on weight at day 3 and feeding mode available were included. The outcome variable was weight loss at day 3 (D3WL), expressed as a percentage of birth weight lost in the first 3 days of life. Our main explanatory variables were maternal pre-pregnancy body mass index (BMI), gestational weight gain, gestational diabetes, birth weight, gestational age and feeding mode. Factors associated with greater D3WL, whatever the feeding mode, were: higher birth weight, gestational diabetes and caesarean section; higher gestational age was associated with a reduced D3WL. The association between maternal pre-pregnancy BMI and D3WL differed by feeding mode (interaction p value=0.0002). In breastfed babies, mean D3WL ranged from 4.9% for neonates of underweight mothers to 5.8% for neonates of obese mothers (p trend=0.0005). In formula-fed babies, D3WL was highest for neonates of underweight mothers (4.1%) and lowest for those of obese mothers (2.6%) (p trend=0.01). The lower D3WL in formula-fed neonates, especially in neonates of obese mothers, suggests a relative overfeeding in the early days compared with breastfed neonates, which may potentially have consequences on later health. Overweight and obese mothers may need extra support to prevent early breastfeeding discontinuation.
Blumenthal, Jacob B; Gitterman, Anna; Ryan, Alice S; Prior, Steven J
2017-01-01
Aerobic exercise training and weight loss (AEX+WL) improves insulin sensitivity in overweight adults; however, the underlying pathways are incompletely understood. Fetuin-A, a hepatokine that inhibits insulin signaling, may be involved in the salutary effects of AEX+WL. Therefore, we examined the effects of 6-month AEX+WL on plasma fetuin-A levels (36-48 hours after the last bout of exercise), aerobic capacity (VO 2max ), body composition, glucose tolerance, and insulin sensitivity (M) in 16 sedentary, overweight-obese older men (age = 60 ± 2 years, BMI = 31 ± 1 kg/m 2 ) with no history of cardiovascular disease or diabetes. At baseline, fetuin-A levels correlated directly with adiposity and had a borderline inverse correlation with M. After AEX+WL, body weight decreased by ~10 kg, while both VO 2max and M increased by 16% ( P < 0.005 for all). Contrary to our hypothesis, plasma fetuin-A levels increased after AEX+WL (1.16 ± 0.10 g/L versus 1.70 ± 0.19 g/L, P = 0.006). This increase was unrelated to changes in body composition or glucose metabolism, but directly correlated with changes in VO 2max ( r = 0.57, P < 0.05). Thus, in overweight-to-obese older men, AEX+WL appears to increase plasma fetuin-A levels. Although not associated with improvements in insulin sensitivity, this increase in fetuin-A was related to improvements in aerobic capacity and could be representative of the cardioprotective effects of AEX+WL in older men.
TEMPORAL EVOLUTION AND SPATIAL DISTRIBUTION OF WHITE-LIGHT FLARE KERNELS IN A SOLAR FLARE
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kawate, T.; Ishii, T. T.; Nakatani, Y.
2016-12-10
On 2011 September 6, we observed an X2.1-class flare in continuum and H α with a frame rate of about 30 Hz. After processing images of the event by using a speckle-masking image reconstruction, we identified white-light (WL) flare ribbons on opposite sides of the magnetic neutral line. We derive the light curve decay times of the WL flare kernels at each resolution element by assuming that the kernels consist of one or two components that decay exponentially, starting from the peak time. As a result, 42% of the pixels have two decay-time components with average decay times of 15.6 andmore » 587 s, whereas the average decay time is 254 s for WL kernels with only one decay-time component. The peak intensities of the shorter decay-time component exhibit good spatial correlation with the WL intensity, whereas the peak intensities of the long decay-time components tend to be larger in the early phase of the flare at the inner part of the flare ribbons, close to the magnetic neutral line. The average intensity of the longer decay-time components is 1.78 times higher than that of the shorter decay-time components. If the shorter decay time is determined by either the chromospheric cooling time or the nonthermal ionization timescale and the longer decay time is attributed to the coronal cooling time, this result suggests that WL sources from both regions appear in 42% of the WL kernels and that WL emission of the coronal origin is sometimes stronger than that of chromospheric origin.« less
Lee, Ji Yeon; Hong, Namki; Kim, Hye Ryun; Lee, Byung Wan; Kang, Eun Seok; Cha, Bong Soo; Lee, Yong Ho
2018-03-01
A recent animal study showed that parathyroid hormone-related peptide (PTHrP) is associated with cancer cachexia by promoting adipose tissue browning, and we previously demonstrated that PTHrP predicts weight loss (WL) in patients with cancer. In this study, we investigated whether prediction of WL by PTHrP is influenced by clinical factors such as serum albumin, corrected calcium levels, cancer stage, and performance status (PS). A cohort of 219 patients with cancer whose PTHrP level was measured was enrolled and followed for body weight (BW) changes. Subjects were divided into two groups by serum albumin (cutoff value, 3.7 g/dL), corrected calcium (cutoff value, 10.5 mg/dL), cancer stage (stage 1 to 3 or 4), or PS (Eastern Cooperative Oncology Group 0 to 1 or 2 to 4), respectively. Clinically significant WL was defined as either percent of BW change (% BW) <-5% or % BW <-2% plus body mass index (BMI) <20 kg/m². After a median follow-up of 327 days, 74 patients (33.8%) experienced clinically significant WL. A positive PTHrP level was associated with a 2-fold increased risk of WL after adjusting for age, baseline BMI, serum albumin, corrected calcium level, cancer stage, and PS. The effect of PTHrP on WL remained significant in patients with low serum albumin, stage 4 cancer, and good PS. Regardless of calcium level, the effect of PTHrP on WL was maintained, although there was an additive effect of higher calcium and PTHrP levels. Early recognition of patients with advanced cancer who are PTHrP positive with hypercalcemia or hypoalbuminemia is needed for their clinical management. Copyright © 2018 Korean Endocrine Society.
Ryan, A S; Li, G; Blumenthal, J B; Ortmeyer, H K
2013-07-01
To determine whether aerobic exercise training + weight loss (AEX + WL) would affect the expression of myostatin and its relationship with insulin sensitivity in a longitudinal, clinical intervention study. Thirty-three obese sedentary postmenopausal women and men (n = 17 and 16, age: 61 ± 1 years, body mass index: 31 ± 1 kg/m(2) , VO2 max: 21.9 ± 1.0 mL/kg/min, X ± Standard error of the mean (SEM)) completed 6 months of 3 days/week AEX + WL. During an 80 mU m(-2) min(-1) hyperinsulinemic-euglycemic clamp, we measured glucose utilization (M), myostatin, myogenin, and MyoD gene expression by real-time RT-PCR in vastus lateralis muscle at baseline and 2 h. Body weight (-8%) and fat mass (-17%) decreased after AEX + WL (P < 0.001). Fat-free mass (FFM) and mid-thigh muscle area by computed tomography did not change but muscle attenuation increased (P < 0.05). VO2 max increased 14% (P < 0.001). AEX + WL increased M by 18% (P < 0.01). Myostatin gene expression decreased 19% after AEX + WL (P < 0.05). Basal mRNA myostatin levels were negatively associated with M before the intervention (r = -0.43, P < 0.05). Insulin infusion increased myoD and myogenin expression before and after AEX + WL (both P < 0.001) but basal levels did not change. The insulin effect on myostatin expression was associated with the change in M after AEX + WL (r = 0.56, P < 0.005). Exercise and weight loss results in a downregulation of myostatin mRNA and an improvement in insulin sensitivity in obese older men and women. Copyright © 2012 The Obesity Society.
Lam, Marnix G E H; Louie, John D; Abdelmaksoud, Mohamed H K; Fisher, George A; Cho-Phan, Cheryl D; Sze, Daniel Y
2014-07-01
To calculate absorbed radiation doses in patients treated with resin microspheres prescribed by the body surface area (BSA) method and to analyze dose-response and toxicity relationships. A retrospective review was performed of 45 patients with colorectal carcinoma metastases who received single-session whole-liver resin microsphere radioembolization. Prescribed treatment activity was calculated using the BSA method. Liver volumes and whole-liver absorbed doses (D(WL)) were calculated. D(WL) was correlated with toxicity and radiographic and biochemical response. The standard BSA-based administered activity (range, 0.85-2.58 GBq) did not correlate with D(WL) (mean, 50.4 Gy; range, 29.8-74.7 Gy; r = -0.037; P = .809) because liver weight was highly variable (mean, 1.89 kg; range, 0.94-3.42 kg) and strongly correlated with D(WL) (r = -0.724; P < .001) but was not accounted for in the BSA method. Patients with larger livers were relatively underdosed, and patients with smaller livers were relatively overdosed. Patients who received D(WL) > 50 Gy experienced more toxicity and adverse events (> grade 2 liver toxicity, 46% vs 17%; P < .05) but also responded better to the treatment than patients who received D(WL)< 50 Gy (disease control, 88% vs 24%; P < .01). Using the standard BSA formula, the administered activity did not correlate with D(WL). Based on this short-term follow-up after salvage therapy in patients with late stage metastatic colorectal carcinoma, dose-response and dose-toxicity relationships support using a protocol based on liver volume rather than BSA to prescribe the administered activity. Copyright © 2014 SIR. Published by Elsevier Inc. All rights reserved.
Fanning, Jason; Walkup, Michael P; Ambrosius, Walter T; Brawley, Lawrence R; Ip, Edward H; Marsh, Anthony P; Rejeski, W Jack
2018-06-01
This article compared the effect of dietary weight loss administered alone (WL) or in combination with aerobic training (WL + AT) or resistance training (WL + RT) on health related quality of life, walking self-efficacy, stair climb self-efficacy, and satisfaction with physical function in older adults with cardiovascular disease or the metabolic syndrome. Participants (N = 249; M age = 66.9) engaged in baseline assessments and were randomly assigned to one of three interventions, each including a 6-month intensive phase and a 12-month follow-up. Those in WL + AT and WL + RT engaged in 4 days of exercise training weekly. All participants engaged in weekly group behavioral weight loss sessions with a goal of 7-10% reduction in body weight. Participants in WL + AT and WL + RT reported better quality of life and satisfaction with physical function at 6- and 18-months relative to WL. At month 6, WL + AT reported greater walking self-efficacy relative to WL + RT and WL, and maintained higher scores compared to WL at month 18. WL + AT and WL + RT reported greater stair climbing efficacy at month 6, and WL + RT remained significantly greater than WL at month 18. The addition of either AT or RT to WL differentially improved HRQOL and key psychosocial outcomes associated with maintenance of physical activity and weight loss. This underscores the important role of exercise in WL for older adults, and suggests health care providers should give careful consideration to exercise mode when designing interventions.
When Does the Warmest Water Reach Greenland?
NASA Astrophysics Data System (ADS)
Grist, J. P.; Josey, S. A.; Boehme, L.; Meredith, M. P.; Laidre, K. L.; Heide-Jørgensen, M. P.; Kovacs, K. M.; Lydersen, C.; Davidson, F. J. M.; Stenson, G. B.; Hammill, M. O.; Marsh, R.; Coward, A.
2016-02-01
The warmest water reaching the east and west coast of Greenland is found between 200 and 600 m, in the warm Atlantic Water Layer (WL). Temperature changes within the WL have been highlighted as a possible cause of accelerated melting of tidewater glaciers and therefore are an important consideration for understanding global sea level rise. However, a limited number of winter observations of the WL have prohibited determining its seasonal variability. To address this, temperature data from Argo profiling floats, a range of sources within the World Ocean Database, and unprecedented coverage from marine-mammal borne sensors have been analyzed for the period 2002-2011. A significant seasonal range in temperature ( 1-2°C) is found in the warm layer, in contrast to most of the surrounding ocean. The magnitude of the seasonal cycle is thus comparable with the 1990s warming that was associated with an increased melt rate in a marine terminating glacier of West Greenland. The phase of the seasonal cycle exhibits considerable spatial variability; with high-resolution ocean model trajectory analysis suggesting it is determined by the time taken for waters to be advected from the subduction site in the Irminger Basin. For western Greenland, the annual temperature maximum occurs near or after the turn of the calendar year. This is significant because a recent study suggested that it is in the non-summer months when fjord-shelf exchanges allow the WL to most strongly influence glacier melt rate. However this is also the time of the year when the WL is least well observed. It is therefore clear that year-round subsurface temperature measurements are still required for a complete description of the WL seasonality, and in particular to ensure that the ice-melting potential of the WL is not underestimated.
Lobley, Gerald E.; Holtrop, Grietje; Bremner, David M.; Calder, A. Graham; Milne, Eric; Johnstone, Alexandra M.
2013-01-01
This study investigated if additional non-starch polysaccharide (NSP) or resistant starch (RS), above that currently recommended, leads to better improvement in insulin sensitivity (IS) than observed with modest weight loss (WL). Obese male volunteers (n = 14) were given an energy-maintenance (M) diet containing 27 g NSP and 5 g RS daily for one week. They then received, in a cross-over design, energy-maintenance intakes of either an NSP-enriched diet (42 g NSP, 2.5 g RS) or an RS-enriched diet (16 g NSP, 25 g RS), each for three weeks. Finally, a high protein (30% calories) WL diet was provided at 8 MJ/day for three weeks. During each dietary intervention, endogenous glucose production (EGP) and IS were assessed. Fasting glycaemia was unaltered by diet, but plasma insulin and C-peptide both decreased with the WL diet (p < 0.001), as did EGP (−11%, p = 0.006). Homeostatis model assessment of insulin resistance improved following both WL (p < 0.001) and RS (p < 0.05) diets. Peripheral tissue IS improved only with WL (57%–83%, p < 0.005). Inclusion of additional RS or NSP above amounts currently recommended resulted in little or no improvement in glycaemic control, whereas moderate WL (approximately 3 kg fat) improved IS. PMID:23752495
Wang, Xiangqian; Wu, Chao; Liu, Nan; Li, Sujing; Li, Wei; Chen, Jianmeng; Chen, Dongzhi
2015-04-01
A Pseudomonas sp. strain WL2 that is able to efficiently metabolize ethyl mercaptan (EM) into diethyl disulfide (DEDS) through enzymatic oxidation was isolated from the activated sludge of a pharmaceutical wastewater plant. One hundred percent removal of 113.5 mg L(-1) EM and 110.3 mg L(-1) DEDS were obtained within 14 and 32 h, respectively. A putative EM degradation pathway that involved the catabolism via DEDS was proposed, which indicated DEDS were further mineralized into carbon dioxide (CO2), bacterial cells, and sulfate (SO4 (2-)) through the transformation of element sulfur and ethyl aldehyde. Degradation kinetics for EM and DEDS with different initial concentrations by strain WL2 were evaluated using Haldane-Andrews model with maximum specific degradation rates of 3.13 and 1.33 g g(-1) h(-1), respectively, and maximum degradation rate constants of 0.522 and 0.175 h(-1) using pseudo-first-order kinetic model were obtained. Results obtained that aerobic degradation of EM by strain WL2 was more efficient than those from previous studies. Substrate range studies of strain WL2 demonstrated its ability to degrade several mercaptans, disulfides, aldehydes, and methanol. All the results obtained highlight the potential of strain WL2 for the use in the biodegradation of volatile organic sulfur compounds (VOSCs).
Probability of loss of assured safety in systems with multiple time-dependent failure modes.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Helton, Jon Craig; Pilch, Martin.; Sallaberry, Cedric Jean-Marie.
2012-09-01
Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high-consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to deactivate the entire system before the SL system fails (i.e., degrades into a configuration that could allowmore » an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). Representations for PLOAS for situations in which both link physical properties and link failure properties are time-dependent are derived and numerically evaluated for a variety of WL/SL configurations, including PLOAS defined by (i) failure of all SLs before failure of any WL, (ii) failure of any SL before failure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS are considered.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Mishchenko, Michael I.; Liu Li; Dlugach, Janna M.
2009-11-10
Several spectacular backscattering effects observed for particulate planetary surfaces have been interpreted in terms of the effect of weak localization (WL) of electromagnetic waves. However, the interference concept of WL explicitly relies on the notion of phase of an electromagnetic wave and is strictly applicable only when particles forming the surface are widely separated. Therefore, one needs a definitive quantitative proof of the WL nature of specific optical effects observed for densely packed particulate media. We use numerically exact computer solutions of the Maxwell equations to simulate electromagnetic scattering by realistic models consisting of large numbers of randomly positioned, denselymore » packed particles. By increasing the particle packing density from zero to approx40%, we track the onset and evolution of the full suite of backscattering optical effects predicted by the low-density theory of WL, including the brightness and polarization opposition effects (BOE and POE). We find that all manifestations of WL, except the circular polarization ratio and POE, are remarkably immune to packing-density effects. Even POE can survive packing densities typical of planetary regolith surfaces. Our numerical data coupled with the results of unique observations at near-backscattering geometries demonstrate that the BOE and POE detected simultaneously for high-albedo solar system objects are caused by the effect of WL.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sabaeian, Mohammad, E-mail: sabaeian@scu.ac.ir; Shahzadeh, Mohammadreza
In this work, the effects of the shape and size on the intersubband electronic and optical properties of three-dimensional self-assembled pyramid-shaped InAs/GaAs quantum dots (QDs) were investigated in detail. More precisely, in-plane- and z-polarized transitions dipole moment (TDM), oscillator strength (OS), and absorption coefficients of P-to-S, WL-to-P, and WL-to-S transitions were studied as a function of the QD height. The P-to-S TDM showed to be strong and purely in-plane-polarized transition dominating two others. However, the TDMs and OSs of WL-to-P and WL-to-S transitions which are in-plane- and z-polarized transitions, respectively, showed a competition behavior for short and tall QDs. Themore » former dominates for short QDs, and the latter for tall QDs. The physical reasons behind these interesting phenomena were also explained using the probability of finding the carriers in the pyramid region attached to the WL. The theoretical results are in good agreement with experimental data reported for short QDs [Appl. Phys. Lett. 82, 630 (2003)].« less
Walsh, T R
2005-02-07
The Wilson-Levy (WL) correlation functional is used together with Hartree-Fock (HF) theory to evaluate interaction energies at intermediate separations (i.e. around equilibrium separation) for several weakly-bonded systems. The HF+WL approach reproduces binding trends for all complexes studied: selected rare-gas dimers, isomers of the methane dimer, benzene dimer and naphthalene dimer, and base-pair stacking structures for pyrimidine, cytosine, uracil and guanine dimers. These HF+WL data are contrasted against results obtained from some popular functionals (including B3LYP and PBE), as well as two newly-developed functionals, X3LYP and xPBE. The utility of HF+WL, with reference to exact-exchange (EXX) density-functional theory, is discussed in terms of a suggested EXXWL exchange-correlation functional.
Agyeman, Fred O; Tao, Wendong
2014-01-15
This study was to comprehensively evaluate the effects of food waste particle size on co-digestion of food waste and dairy manure at organic loading rates increased stepwise from 0.67 to 3 g/L/d of volatile solids (VS). Three anaerobic digesters were fed semi-continuously with equal VS amounts of food waste and dairy manure. Food waste was ground to 2.5 mm (fine), 4 mm (medium), and 8 mm (coarse) for the three digesters, respectively. Methane production rate and specific methane yield were significantly higher in the digester with fine food waste. Digestate dewaterability was improved significantly by reducing food waste particle size. Specific methane yield was highest at the organic loading rate of 2g VS/L/d, being 0.63, 0.56, and 0.47 L CH4/g VS with fine, medium, and coarse food waste, respectively. Methane production rate was highest (1.40-1.53 L CH4/L/d) at the organic loading rate of 3 g VS/L/d. The energy used to grind food waste was minor compared with the heating value of the methane produced. Copyright © 2013 Elsevier Ltd. All rights reserved.
Thermal characterization of organic matter along a (hypothetical) coalification gradient
NASA Astrophysics Data System (ADS)
Cavallo, Ornella; Provenzano, Maria Rosaria; Zaccone, Claudio
2017-04-01
Geochemical transformations of organic carbon (C) in aquatic and terrestrial ecosystems are important starting points for genesis of peats, brown coals and other coal precursors. The humification process plays a key role in biogeochemical transformations of organic C and, as a result, in the first stages of coal precursors formation. Thermal analysis was used by Schnitzer and other scientists since 1950-1960s, in order to investigate the stability of several organic materials of industrial value including peat and coal. What soil scientists found was the general occurrence of two exothermic peaks (exotherm 1 and 2) due to decomposition and combustion reactions of organic compounds having different thermal stability and, consequently, different degree of humification. Thermogravimetric analysis (TG) was carried out on different samples reproducing a "hypothetical" coalification gradient as follows: peat (IHSS Pahokee peat standard), fulvic acid (FA), a peat humic acid (HA), leonardite (IHSS Gascoyne standard) and charcoal. An aliquot of about 20 mg of each sample was heated in a ceramic crucible from 50 to 850˚ C at 30˚ C min-1, at a gas flow rate of 30 mL min-1 using a PerkinElmer TGA4000 thermobalance. Samples were analysed both under nitrogen and under synthetic air. All analyses were carried out in triplicate and the average coefficient of variation was <1.5%. Weight losses (in %) were determined within 200-400˚ C (WL1) and 400-600˚ C (WL2) temperature ranges, and the ratio between WL2/WL1 calculated for all samples. This ratio has been often used as a highly sensitive parameter to describe chemical changes induced by the bio-transformation of organic materials. Finally, the temperature at which half of the exothermic mass loss has occurred (TG-T50) was also calculated. Preliminary results obtained from TG analysis under air showed that WL2/WL1 ratio was lower for the FA sample and higher for leonardite and charcoal, following the order FA
NASA Astrophysics Data System (ADS)
Xiong, Ming; Davies, Jackie A.; Harrison, Richard A.; Zhou, Yufen; Feng, Xueshang; Xia, Lidong; Li, Bo; Liu, Ying D.; Hayashi, Keiji; Li, Huichao; Yang, Liping
2018-01-01
The in-flight performance of the Coriolis/SMEI and STEREO/HI instruments substantiates the high-technology readiness level of white-light (WL) imaging of coronal mass ejections (CMEs) in the inner heliosphere. The WL intensity of a propagating CME is jointly determined by its evolving mass distribution and the fixed Thomson-scattering geometry. From their in-ecliptic viewpoints, SMEI and HI, the only heliospheric imagers that have been flown to date, integrate the longitudinal dimension of CMEs. In this paper, using forward magnetohydrodynamic modeling, we synthesize the WL radiance pattern of a typical halo CME viewed from an out-of-ecliptic (OOE) vantage point. The major anatomical elements of the CME identified in WL imagery are a leading sheath and a trailing ejecta; the ejecta-driven sheath is the brightest feature of the CME. The sheath, a three-dimensional (3D) dome-like density structure, occupies a wide angular extent ahead of the ejecta itself. The 2D radiance pattern of the sheath depends critically on viewpoint. For a CME modeled under solar minimum conditions, the WL radiance pattern of the sheath is generally a quasi-straight band when viewed from an in-ecliptic viewpoint and a semicircular arc from an OOE viewpoint. The dependence of the radiance pattern of the ejecta-driven sheath on viewpoint is attributed to the bimodal nature of the 3D background solar wind flow. Our forward-modeling results suggest that OOE imaging in WL radiance can enable (1) a near-ecliptic CME to be continuously tracked from its coronal initiation, (2) the longitudinal span of the CME to be readily charted, and (3) the transporting speed of the CME to be reliably determined. Additional WL polarization measurements can significantly limit the ambiguity of localizing CMEs. We assert that a panoramic OOE view in WL would be highly beneficial in revealing CME morphology and kinematics in the hitherto-unresolved longitudinal dimension and hence for monitoring the propagation and evolution of near-ecliptic CMEs for space weather operations.
Von Thun, Nancy L.; Sukumar, Deeptha; Heymsfield, Steven B.; Shapses, Sue A.
2016-01-01
Objective Short-term weight loss is accompanied by bone loss in postmenopausal women. The longer-term impact on bone in the reduced overweight/obese woman compared to those who regain their weight was examined in this study using a case-control design. Methods Postmenopausal women (n = 42, body mass index of 28.3 ± 2.8 kg/m2; 60.7 ± 5.5 y) were recruited 2 years after the start of a 6 month weight loss trial and those who maintained their weight (WL-M) were matched to a cohort who regained weight (WL-R). Serum hormones and bone markers were measured in a subset. Bone mineral density (BMD) at the femoral neck (FN), trochanter, spine, radius, and total body and soft tissue composition were taken at baseline, 0.5 and 2 years. Results During WL, both groups lost 9.3 ± 3.4% body weight with no significant difference between groups. After weight loss, weight change was −0.1 ± 2.7 % and 6.0 ± 3.3% in the WL-M (n=22) and WL-R (n=20) groups, respectively. After 2 years, both groups lost BMD at the FN and trochanter (p ≤ 0.01), whereas only the WL-M group reduced BMD at the 1/3 radius (p < 0.001). There was a greater BMD loss at the trochanter (−6.8 ± 5.7%) and the 1/3 radius (−4.5 ± 3.3%) in the WL-M compared to the WL-R group after 2 years. Multiple linear regression showed that change in leg fat mass (but not trunk fat) contributed to trochanter BMD loss (p <0.05). Conclusions After 2 years, there is no BMD recovery of weight reduction-induced bone loss, irrespective of weight-regain. These data suggest that the period after weight loss may be an important point in time to prevent bone loss for both those who maintain or regain weight. PMID:24149920
Kaltenbach, T; Friedland, S; Soetikno, R
2008-10-01
Colonoscopy, the "gold standard" screening test for colorectal cancer (CRC), has known diagnostic limitations. Advances in endoscope technology have focused on improving mucosal visualisation. In addition to increased angle of view and resolution features, recent colonoscopes have non-white-light optics, such as narrow band imaging (NBI), to enhance image contrast. We aimed to study the neoplasia diagnostic characteristics of NBI, by comparing the neoplasm miss rate when the colonoscopy was performed under NBI versus white light (WL). Randomised controlled trial. US Veterans hospital. Elective colonoscopy adults. We randomly assigned patients to undergo a colonoscopic examination using NBI or WL. All patients underwent a second examination using WL, as the reference standard. The primary end point was the difference in the neoplasm miss rate, and secondary outcome was the neoplasm detection rate. In 276 tandem colonoscopy patients, there was no significant difference of miss or detection rates between NBI or WL colonoscopy techniques. Of the 135 patients in the NBI group, 17 patients (12.6%; 95% confidence interval (CI) 7.5 to 19.4%) had a missed neoplasm, as compared with 17 of the 141 patients (12.1%; 95% CI 7.2 to 18.6%) in the WL group, with a miss rate risk difference of 0.5% (95% CI -7.2 to 8.3). 130 patients (47%) had at least one neoplasm. Missed lesions with NBI showed similar characteristics to those missed with WL. All missed neoplasms were tubular adenomas, the majority (78%) was < or = 5 mm and none were larger than 1 cm (one-sided 95% CI up to 1%). Nonpolypoid lesions represented 35% (13/37) of missed neoplasms. NBI did not improve the colorectal neoplasm miss rate compared to WL; the miss rate for advanced adenomas was less than 1% and for all adenomas was 12%. The neoplasm detection rates were similar high using NBI or WL; almost a half the study patients had at least one adenoma. Clinicaltrials.gov identifier: NCT00628147.
Caruana, Joseph A; Monte, Scott V; Jacobs, David M; Voytovich, Catherine; Ghanim, Husam; Dandona, Paresh
2015-01-01
For patients with poor weight loss (WL) after Roux-en-Y gastric bypass (RYGB) there are few well-tolerated and effective surgical options. Revision to distal bypass by shortening of the common channel (CC) induces significant WL but often produces protein calorie malnutrition (PCM) and severe diarrhea. The aim of this study was to identify a safe and effective threshold for distal small bowel bypass when done for revision of gastric bypass. Academic Institution, United States. We performed revision of RYGB for WL in 20 patients by shortening the CC to a new length of 120-300 cm. The Roux limb length was unchanged. WL and PCM were monitored. A threshold for percent of small bowel bypassed at which PCM was avoided was retrospectively determined. WL was then compared in patients above and below this threshold. Five patients completed a 250-kcal mixed meal challenge before and 3 months after revision to determine selected gut hormone responses. Bypassing ≥70% small bowel resulted in PCM in 4 of 10 patients but in none of 10 patients below that threshold. PCM was observed as late as 2 years after revision and necessitated rerevision by lengthening of the CC in 3 patients. Additionally, nocturnal diarrhea was more common and more intractable when ≥70% bypass was done. Both groups had significant excess body WL over 2 years, but it was greater in patients with ≥70% bypass (47±19 versus 26±17; P<.05). A favorable gut hormone response was observed with 3-hour decrease in glucose-dependent insulinotropic peptide (GIP) by 25% and increase in glucagon-like peptide-1 (GLP-1) by 25%, whereas fasting peptide-YY (PYY) increased by 71% (P<.05 for all). Revision of RYGB to distal bypass when it is <70% of a patient's small bowel length results in an acceptable balance of WL and a positive safety profile. WL may be mediated through an enhanced gut hormone effect, an aversion to ingested fat, and possibly other mechanisms. Copyright © 2015 American Society for Bariatric Surgery. Published by Elsevier Inc. All rights reserved.
Effect of a water-based drilling waste on receiving soil properties and plants growth.
Saint-Fort, Roger; Ashtani, Sahar
2014-01-01
This investigation was undertaken to determine the relative effects of recommended land spraying while drilling (LWD) loading rate application for a source of water-based drilling waste material on selected soil properties and phytotoxicity. Drilling waste material was obtained from a well where a nitrate gypsum water based product was used to formulate the drilling fluid. The fluid and associated drill cuttings were used as the drilling waste source to conduct the experiment. The study was carried out in triplicate and involved five plant species, four drilling waste loading rates and a representative agricultural soil type in Alberta. Plant growth was monitored for a period of ten days. Drilling waste applied at 10 times above the recommended loading rate improved the growth and germination rate of all plants excluding radish. Loading rates in excess of 40 and 50 times had a deleterious effect on radish, corn and oat but not on alfalfa and barley. Germination rate decreased as waste loading rate increased. Effects on soil physical and chemical properties were more pronounced at the 40 and 50 times exceeding recommended loading rate. Significant changes in soil parameters occurred at the higher rates in terms of increase in soil porosity, pH, EC, hydraulic conductivity, SAR and textural classification. This study indicates that the applications of this type of water based drill cutting if executed at an optimal loading rate, may improve soil quality and results in better plant growth.
40 CFR 60.1320 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2014 CFR
2014-07-01
... municipal waste combustion unit? 60.1320 Section 60.1320 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After... Monitoring Requirements § 60.1320 How do I monitor the load of my municipal waste combustion unit? (a) If...
40 CFR 60.1320 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2010 CFR
2010-07-01
... municipal waste combustion unit? 60.1320 Section 60.1320 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After... Monitoring Requirements § 60.1320 How do I monitor the load of my municipal waste combustion unit? (a) If...
40 CFR 60.1320 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2013 CFR
2013-07-01
... municipal waste combustion unit? 60.1320 Section 60.1320 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After... Monitoring Requirements § 60.1320 How do I monitor the load of my municipal waste combustion unit? (a) If...
40 CFR 60.1320 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2011 CFR
2011-07-01
... municipal waste combustion unit? 60.1320 Section 60.1320 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After... Monitoring Requirements § 60.1320 How do I monitor the load of my municipal waste combustion unit? (a) If...
40 CFR 60.1320 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2012 CFR
2012-07-01
... municipal waste combustion unit? 60.1320 Section 60.1320 Protection of Environment ENVIRONMENTAL PROTECTION... of Performance for Small Municipal Waste Combustion Units for Which Construction is Commenced After... Monitoring Requirements § 60.1320 How do I monitor the load of my municipal waste combustion unit? (a) If...
Potential Impacts of Organic Wastes on Small Stream Water Quality
NASA Astrophysics Data System (ADS)
Kaushal, S. S.; Groffman, P. M.; Findlay, S. E.; Fischer, D. T.; Burke, R. A.; Molinero, J.
2005-05-01
We monitored concentrations of dissolved organic carbon (DOC), dissolved oxygen (DO) and other parameters in 17 small streams of the South Fork Broad River (SFBR) watershed on a monthly basis for 15 months. The subwatersheds were chosen to reflect a range of land uses including forested, pasture, mixed, and developed. The SFBR watershed is heavily impacted by organic wastes, primarily from its large poultry industry, but also from its rapidly growing human population. The poultry litter is primarily disposed of by application to pastures. Our monthly monitoring results showed a strong inverse relationship between mean DOC and mean DO and suggested that concentrations of total nitrogen (TN), DOC, and the trace gases nitrous oxide, methane and carbon dioxide are impacted by organic wastes and/or nutrients from animal manure applied to the land and/or human wastes from wastewater treatment plants or septic tanks in these watersheds. Here we estimate the organic waste loads of these watersheds and evaluate the impact of organic wastes on stream DOC and alkalinity concentrations, electrical conductivity, sediment potential denitrification rate and plant stable nitrogen isotope ratios. All of these water quality parameters are significantly correlated with watershed waste loading. DOC is most strongly correlated with total watershed waste loading whereas conductivity, alkalinity, potential denitrification rate and plant stable nitrogen isotope ratio are most strongly correlated with watershed human waste loading. These results suggest that more direct inputs (e.g., wastewater treatment plant effluents, near-stream septic tanks) have a greater relative impact on stream water quality than more dispersed inputs (land applied poultry litter, septic tanks far from streams) in the SFBR watershed. Conductivity, which is generally elevated in organic wastes, is also significantly correlated with total watershed waste loading suggesting it may be a useful indicator of overall watershed waste loading. Although this work was reviewed by EPA and approved for publication, it may not necessarily reflect official Agency policy.
Tracy, J.C.; Bernknopf, R.; Forney, W.; Hill, K.
2004-01-01
The Federal Clean Water Act (Section 303(d)) mandates that states develop Total Maximum Daily Load (TMDL) plans for water bodies that are on the Section 303(d) list. To be placed on the 303(d) list, a water body must be found to have water quality conditions that limit its ability to meet its designated beneficial uses. The TMDL for a water body is defined in 40 CFR 130 as the sum of waste load allocations from identified points sources and non-point sources within the water body's watershed. The TMDL plan for a listed water body should identify the current waste loads to the water body, the waste load capacity of the water body and then allocate the waste load capacity to the known point and non-point sources of pollution within the water body's watershed. Copyright 2004 ASCE.
NASA Astrophysics Data System (ADS)
Liu, Na; Ju, Cheng
2018-02-01
Nyquist-SCM signal after fiber transmission, direct detection (DD), and analog down-conversion suffers from linear ISI, nonlinear ISI, and I/Q imbalance, simultaneously. Theoretical analysis based on widely linear (WL) and Volterra series is given to explain the relationship and interaction of these three interferences. A blind equalization algorithm, cascaded WL and Volterra equalizer, is designed to mitigate these three interferences. Furthermore, the feasibility of the proposed cascaded algorithm is experimentally demonstrated based on a 40-Gbps data rate 16-quadrature amplitude modulation (QAM) virtual single sideband (VSSB) Nyquist-SCM DD system over 100-km standard single mode fiber (SSMF) transmission. In addition, the performances of conventional strictly linear equalizer, WL equalizer, Volterra equalizer, and cascaded WL and Volterra equalizer are experimentally evaluated, respectively.
Joint multifractal analysis based on wavelet leaders
NASA Astrophysics Data System (ADS)
Jiang, Zhi-Qiang; Yang, Yan-Hong; Wang, Gang-Jin; Zhou, Wei-Xing
2017-12-01
Mutually interacting components form complex systems and these components usually have long-range cross-correlated outputs. Using wavelet leaders, we propose a method for characterizing the joint multifractal nature of these long-range cross correlations; we call this method joint multifractal analysis based on wavelet leaders (MF-X-WL). We test the validity of the MF-X-WL method by performing extensive numerical experiments on dual binomial measures with multifractal cross correlations and bivariate fractional Brownian motions (bFBMs) with monofractal cross correlations. Both experiments indicate that MF-X-WL is capable of detecting cross correlations in synthetic data with acceptable estimating errors. We also apply the MF-X-WL method to pairs of series from financial markets (returns and volatilities) and online worlds (online numbers of different genders and different societies) and determine intriguing joint multifractal behavior.
Bernardi, A; Ossó, J O; Alonso, M I; Goñi, A R; Garriga, M
2006-05-28
We have studied the epitaxial growth of self-assembled Ge quantum dots when a submonolayer of carbon is deposited on a Ge wetting layer (WL) prior to the growth of the dots. Using atomic-force microscopy combined with optical techniques like Raman and ellipsometry, we performed a systematic study of the role played by thermally activated Si interdiffusion on dot density, composition and morphology, by changing only the growth temperature T(WL) of the WL. Strikingly, we observe that higher dot densities and a narrower size distribution are achieved by increasing the deposition temperature T(WL), i.e. by enhancing Si interdiffusion from the substrate. We suggest a two-stage growth procedure for fine tuning of dot topography (density, shape and size) useful for possible optoelectronic applications.
NASA Astrophysics Data System (ADS)
Trudel, M.; Desrochers, N.; Leconte, R.
2017-12-01
Knowledge of water extent (WE) and level (WL) of rivers is necessary to calibrate and validate hydraulic models and thus to better simulate and forecast floods. Synthetic aperture radar (SAR) has demonstrated its potential for delineating water bodies, as backscattering of water is much lower than that of other natural surfaces. The ability of SAR to obtain information despite cloud cover makes it an interesting tool for temporal monitoring of water bodies. The delineation of WE combined with a high-resolution digital terrain model (DTM) allows extracting WL. However, most research using SAR data to calibrate hydraulic models has been carried out using one or two images. The objectives of this study is to use WL derived from time series high resolution Radarsat-2 SAR images for the calibration of a 1-D hydraulic model (HEC-RAS). Twenty high-resolution (5 m) Radarsat-2 images were acquired over a 40 km reach of the Athabasca River, in northern Alberta, Canada, between 2012 and 2016, covering both low and high flow regimes. A high-resolution (2m) DTM was generated combining information from LIDAR data and bathymetry acquired between 2008 and 2016 by boat surveying. The HEC-RAS model was implemented on the Athabasca River to simulate WL using cross-sections spaced by 100 m. An image histogram thresholding method was applied on each Radarsat-2 image to derive WE. WE were then compared against each cross-section to identify those were the slope of the banks is not too abrupt and therefore amenable to extract WL. 139 observations of WL at different locations along the river reach and with streamflow measurements were used to calibrate the HEC-RAS model. The RMSE between SAR-derived and simulated WL is under 0.35 m. Validation was performed using in situ observations of WL measured in 2008, 2012 and 2016. The RMSE between the simulated water levels calibrated with SAR images and in situ observations is less than 0.20 m. In addition, a critical success index (CSI) was performed to compare the WE simulated by HEC-RAS and that derived from SARs images. The CSI is higher than 0.85 for each date, which means that simulated WE is highly similar to the WE derived from SARs images. Thereby, the results of our analysis indicate that calibration of a hydraulic model can be performed from WL derived from time series of high-resolution SAR images.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Raszewski, F; Tommy Edwards, T; David Peeler, D
Sludge Batch 4 (SB4) is currently being processed in the Defense Waste Processing Facility (DWPF) using Frit 510. The slurry pumps in Tank 40 are experiencing in-leakage of bearing water, which is causing the sludge slurry in Tank 40 to become dilute at a rapid rate. Currently, the DWPF is removing this dilution water by performing caustic boiling during the Sludge Receipt and Adjustment Tank (SRAT) cycle. In order to alleviate prolonged SRAT cycle times, which may eventually impact canister production rates, the Liquid Waste Organization (LWO) performed a 100K gallon supernate decant of Tank 40 in April 2008. SRNLmore » performed a supplemental glass variability study to support the April 2008 100K gallon decant incorporating the impact of coupled operations (addition of the Actinide Removal Process (ARP) stream). Recently LWO requested that SRNL assess the impact of a second decant (up to 100K gallon) to the Frit 510-SB4 system. This second decant occurred in June 2008. LWO provided nominal compositions on May 6, 2008 representing Tank 40 prior to the second decant, following the second decant, and the SB4 Heel prior to blending with Tank 51 to constitute SB5. Paper study assessments were performed for these options based on sludge-only and coupled operations processing (ARP addition), as well as possible Na{sub 2}O additions (via NaOH additions) to both flowsheets. A review of the ComProTM database relative to the compositional region defined by the projections after the second decant coupled with Frit 510 identified only a few glasses with similar glass compositions. These glasses were acceptable from a durability perspective, but did not sufficiently cover the new glass compositional region. Therefore, SRNL recommended that a supplemental variability study be performed to support the June 2008 Tank 40 decant. Glasses were selected for the variability study based on three sludge compositional projections (sludge-only, coupled and coupled + 2 wt% Na{sub 2}O) at waste loadings (WLs) of interest to DWPF (32%, 35% and 38%). These nine glasses were fabricated and characterized using chemical composition analysis, X-ray Diffraction (XRD) and the Product Consistency Test (PCT). All of the glasses that were selected for this study satisfy the Product Composition Control System (PCCS) criteria and are deemed processable and acceptable for the DWPF, except for the SB4VS2-03 (sludge-only at 38% WL) target composition. This glass fails the T{sub L} criterion and would not be considered processable based on Slurry Mix Evaporator (SME) acceptability decisions. The durabilities of all of the study glasses (both quenched and ccc) are well below that of the normalized leachate for boron (NL [B]) of the reference EA glass (16.695 g/L) and are predictable using the current PCCS models. Very little variation exists between the NL [B] of the quenched and ccc versions of the glasses. There is some evidence of a trend toward a less durable glass as WL increases for some of the sludge projections. Frit 510 is a viable option for the processing of SB4 after a second Tank 40 decant with or without the addition of products from the ARP stream as well as the 2 wt% Na{sub 2}O addition. The addition of ARP had no negative impacts on the acceptability and predictability of the variability study glasses.« less
NASA Technical Reports Server (NTRS)
Brock, T. G.; Cleland, R. E.
1990-01-01
Rapid cell enlargement in primary leaves of bean is induced by bright white light (WL), gibberellic acid (GA3) or the cytokinin N6-benzyladenine (BA). In previous studies it has been show that all three agents cause an increase in wall extensibility, although by different mechanisms. Here we examine the effects of the three growth promoters on the osmotic potential difference (delta Psi), the accumulation of solutes (delta TSC), the wall yield threshold (Y) and the growth potential (delta Psi -Y). With GA3 and BA, but not WL, there was a rapid decline in delta Psi as measured by the osmotic concentration of expressed sap. Unlike WL, neither GA3 nor BA promoted the accumulation of osmotic solutes. The decline in delta Psi, however, was apparently counteracted by a decline in Y since the growth potential, as measured by the external-osmoticum method, remained unchanged. It is concluded that WL, GA3 and BA all promote cell enlargement of bean leaves by increasing one cellular growth parameter, wall extensibility. Only WL, however, promotes osmotic adjustment during growth.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Helton, Jon C.; Brooks, Dusty Marie; Sallaberry, Cedric Jean-Marie.
Representations for margins associated with loss of assured safety (LOAS) for weak link (WL)/strong link (SL) systems involving multiple time-dependent failure modes are developed. The following topics are described: (i) defining properties for WLs and SLs, (ii) background on cumulative distribution functions (CDFs) for link failure time, link property value at link failure, and time at which LOAS occurs, (iii) CDFs for failure time margins defined by (time at which SL system fails) – (time at which WL system fails), (iv) CDFs for SL system property values at LOAS, (v) CDFs for WL/SL property value margins defined by (property valuemore » at which SL system fails) – (property value at which WL system fails), and (vi) CDFs for SL property value margins defined by (property value of failing SL at time of SL system failure) – (property value of this SL at time of WL system failure). Included in this presentation is a demonstration of a verification strategy based on defining and approximating the indicated margin results with (i) procedures based on formal integral representations and associated quadrature approximations and (ii) procedures based on algorithms for sampling-based approximations.« less
Thomas, Colleen; Manin, Timofey B; Andriyasov, Artem V; Swayne, David E
2008-09-01
Chickens were intranasally inoculated with the swine influenza virus (SIV) A/swine/NC/307408/04 (H3N2) (NC/04 SIV) to determine the infectivity of a North American SIV for chickens, as well as the possibility of chicken meat serving as a transmission vehicle for SIV. White leghorn (WL) layer-type chickens were used for initial pathotyping and infectivity tests, and a more comprehensive intranasal pathogenesis study was done with white Plymouth rock (WPR) broiler-type chickens. None of the NC/04 SIV-inoculated WL or WPR chickens displayed clinical signs. Serologic tests showed that the virus was able to infect both intranasally inoculated WL and WPR chickens, but the antibody titers were low, suggesting inefficient replication. Some of the NC/04 SIV-inoculated WL chickens shed low levels of virus, mostly from the alimentary tract, but viral shedding was not detected in NC/04 SIV-inoculated WPR chickens. The comprehensive pathogenesis study demonstrated that the virus did not cause systemic infections in WPR chickens, and feeding breast and thigh meat from the NC/04 SIV-inoculated WPR to WL chickens did not transmit NC/04 SIV.
WL 17: A Young Embedded Transition Disk
NASA Astrophysics Data System (ADS)
Sheehan, Patrick D.; Eisner, Josh A.
2017-05-01
We present the highest spatial resolution ALMA observations to date of the Class I protostar WL 17 in the ρ Ophiuchus L1688 molecular cloud complex, which show that it has a 12 au hole in the center of its disk. We consider whether WL 17 is actually a Class II disk being extincted by foreground material, but find that such models do not provide a good fit to the broadband spectral energy distribution (SED) and also require such high extinction that it would presumably arise from dense material close to the source, such as a remnant envelope. Self-consistent models of a disk embedded in a rotating collapsing envelope can nicely reproduce both the ALMA 3 mm observations and the broadband SED of WL 17. This suggests that WL 17 is a disk in the early stages of its formation, and yet even at this young age the inner disk has been depleted. Although there are multiple pathways for such a hole to be created in a disk, if this hole was produced by the formation of planets it could place constraints on the timescale for the growth of planets in protoplanetary disks.
Gersing, A S; Solka, M; Joseph, G B; Schwaiger, B J; Heilmeier, U; Feuerriegel, G; Nevitt, M C; McCulloch, C E; Link, T M
2016-07-01
To investigate compositional cartilage changes measured with 3T MRI-based T2 values over 48 months in overweight and obese individuals with different degrees of weight loss (WL) and to study whether WL slows knee cartilage degeneration and symptom worsening. We studied participants from the Osteoarthritis Initiative with risk factors or radiographic evidence of mild to moderate knee osteoarthritis with a baseline BMI ≥25 kg/m(2). We selected subjects who over 48 months lost a, moderate (BMI change, 5-10%WL, n = 180) or large amount of weight (≥10%WL, n = 78) and frequency-matched these to individuals with stable weight (<3%, n = 258). Right knee cartilage T2 maps of all compartments and grey-level co-occurrence matrix (GLCM) texture analyses were evaluated and associations with WL and clinical symptoms (WOMAC subscales for pain, stiffness and disability) were assessed using multivariable regression models. The amount of weight change was significantly associated with change in cartilage T2 of the medial tibia (β 0.9 ms, 95% CI 0.4 to 1.1, P = 0.001). Increase of T2 in the medial tibia was significantly associated with increase in WOMAC pain (β 0.5 ms, 95% CI 0.2 to 0.6, P = 0.02) and disability (β 0.03 ms, 95% CI 0.003 to 0.05, P = 0.03). GLCM contrast and variance over all compartments showed significantly less progression in the >10%WL group compared to the stable weight group (both comparisons, P = 0.04). WL over 48 months is associated with slowed knee cartilage degeneration and improved knee symptoms. Copyright © 2016 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.
Yadav, Inderjit S.; Sharma, Amandeep; Kaur, Satinder; Nahar, Natasha; Bhardwaj, Subhash C.; Sharma, Tilak R.; Chhuneja, Parveen
2016-01-01
Leaf rust caused by Puccinia triticina (Pt) is one of the most important diseases of bread wheat globally. Recent advances in sequencing technologies have provided opportunities to analyse the complete transcriptomes of the host as well as pathogen for studying differential gene expression during infection. Pathogen induced differential gene expression was characterized in a near isogenic line carrying leaf rust resistance gene Lr57 and susceptible recipient genotype WL711. RNA samples were collected at five different time points 0, 12, 24, 48, and 72 h post inoculation (HPI) with Pt 77-5. A total of 3020 transcripts were differentially expressed with 1458 and 2692 transcripts in WL711 and WL711+Lr57, respectively. The highest number of differentially expressed transcripts was detected at 12 HPI. Functional categorization using Blast2GO classified the genes into biological processes, molecular function and cellular components. WL711+Lr57 showed much higher number of differentially expressed nucleotide binding and leucine rich repeat genes and expressed more protein kinases and pathogenesis related proteins such as chitinases, glucanases and other PR proteins as compared to susceptible genotype. Pathway annotation with KEGG categorized genes into 13 major classes with carbohydrate metabolism being the most prominent followed by amino acid, secondary metabolites, and nucleotide metabolism. Gene co-expression network analysis identified four and eight clusters of highly correlated genes in WL711 and WL711+Lr57, respectively. Comparative analysis of the differentially expressed transcripts led to the identification of some transcripts which were specifically expressed only in WL711+Lr57. It was apparent from the whole transcriptome sequencing that the resistance gene Lr57 directed the expression of different genes involved in building the resistance response in the host to combat invading pathogen. The RNAseq data and differentially expressed transcripts identified in present study is a genomic resource which can be used for further studying the host pathogen interaction for Lr57 and wheat transcriptome in general. PMID:28066494
External modes in quantum dot light emitting diode with filtered optical feedback
NASA Astrophysics Data System (ADS)
Al Husseini, Hussein B.; Al Naimee, Kais A.; Al-Khursan, Amin H.; Khedir, Ali. H.
2016-06-01
This research reports a theoretical investigation on the role of filtered optical feedback (FOF) in the quantum dot light emitting diode (QD-LED). The underlying dynamics is affected by a sidle node, which returns to an elliptical shape when the wetting layer (WL) is neglected. Both filter width and time delay change the appearance of different dynamics (chaotic and mixed mode oscillations, MMOs). The results agree with the experimental observations. Here, the fixed point analysis for QDs was done for the first time. For QD-LED with FOF, the system transits from the coherence collapse case in conventional optical feedback to a coherent case with a filtered mode in FOF. It was found that the WL washes out the modes which is an unexpected result. This may attributed to the longer capture time of WL compared with that between QD states. Thus, WL reduces the chaotic behavior.
External modes in quantum dot light emitting diode with filtered optical feedback
DOE Office of Scientific and Technical Information (OSTI.GOV)
Al Husseini, Hussein B.; Department of Physics, College of Science, University of Baghdad, Al Jadiriyah, Baghdad; Al Naimee, Kais A.
2016-06-14
This research reports a theoretical investigation on the role of filtered optical feedback (FOF) in the quantum dot light emitting diode (QD-LED). The underlying dynamics is affected by a sidle node, which returns to an elliptical shape when the wetting layer (WL) is neglected. Both filter width and time delay change the appearance of different dynamics (chaotic and mixed mode oscillations, MMOs). The results agree with the experimental observations. Here, the fixed point analysis for QDs was done for the first time. For QD-LED with FOF, the system transits from the coherence collapse case in conventional optical feedback to amore » coherent case with a filtered mode in FOF. It was found that the WL washes out the modes which is an unexpected result. This may attributed to the longer capture time of WL compared with that between QD states. Thus, WL reduces the chaotic behavior.« less
Rigorous control conditions diminish treatment effects in weight loss randomized controlled trials
Dawson, John A.; Kaiser, Kathryn A.; Affuso, Olivia; Cutter, Gary R.; Allison, David B.
2015-01-01
Background It has not been established whether control conditions with large weight losses (WLs) diminish expected treatment effects in WL or prevention of weight gain (PWG) randomized controlled trials (RCTs). Subjects/Methods We performed a meta-analysis of 239 WL/PWG RCTs that include a control group and at least one treatment group. A maximum likelihood meta-analysis framework is used in order to model and understand the relationship between treatment effects and control group outcomes. Results Under the informed model, an increase in control group WL of one kilogram corresponds with an expected shrinkage of the treatment effect by 0.309 kg [95% CI (−0.480, −0.138), p = 0.00081]; this result is robust against violations of the model assumptions. Conclusions We find that control conditions with large weight losses diminish expected treatment effects. Our investigation may be helpful to clinicians as they design future WL/PWG studies. PMID:26449419
Melter Throughput Enhancements for High-Iron HLW
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, A. A.; Gan, Hoa; Joseph, Innocent
2012-12-26
This report describes work performed to develop and test new glass and feed formulations in order to increase glass melting rates in high waste loading glass formulations for HLW with high concentrations of iron. Testing was designed to identify glass and melter feed formulations that optimize waste loading and waste processing rate while meeting all processing and product quality requirements. The work included preparation and characterization of crucible melts to assess melt rate using a vertical gradient furnace system and to develop new formulations with enhanced melt rate. Testing evaluated the effects of waste loading on glass properties and themore » maximum waste loading that can be achieved. The results from crucible-scale testing supported subsequent DuraMelter 100 (DM100) tests designed to examine the effects of enhanced glass and feed formulations on waste processing rate and product quality. The DM100 was selected as the platform for these tests due to its extensive previous use in processing rate determination for various HLW streams and glass compositions.« less
JWST ISIM Harness Thermal Evaluation
NASA Technical Reports Server (NTRS)
Kobel, Mark; Glazer, Stuart; Tuttle, Jim; Martins, Mario; Ruppel, Sean
2008-01-01
The James Webb Space Telescope (JWST) will be a large infrared telescope with a 6.5-meter primary mirror. Launch is planned for 2013. JWST wl1 be the premier observatory of the next decade serving thousands of astronomers worldwide. The Integrated Science Instrument Module (ISIM) is the unit that will house thc four main JWST instruments. The ISIM enclosure passively cooled to 37 Kelvin and has a tightly managed thermal budget. A significant portion of the ISIM heat load is due to parasitic heat gains from the instrument harnesses. These harnesses provide a thermal path from the Instrument Electronics Control (IEC) to the ISIM. Because of the impact of this load to the ISIM thermal design, understanding the harness parasitic heat gains is critical. To this effect, a thermal test program has been conducted in order to characterize these parasitic loads and verify harness thermal models. Recent parasitic heat loads tests resulted in the addition of a dedicated multiple stage harness radiator. In order for the radiator to efficiently reject heat from the harness, effective thermal contact conductance values for multiple harnesses had to be determined. This presentation will describe the details and the results of this test program.
Use of hydrogel breast biopsy tissue markers reduces the need for wire localization.
Blumencranz, Peter W; Ellis, Debra; Barlowe, Kylee
2014-10-01
The purpose of this study was to determine whether breast biopsy tissue markers composed of an ultrasound-visible hydrogel reduced the need for preoperative wire localization (WL) in patients undergoing a partial mastectomy. A single-surgeon, single-institution, retrospective chart review was performed on 691 consecutive female patients, with mean age 67 years (range 36-98 years), from 2009 to 2012 undergoing partial mastectomies after percutaneous biopsies by stereotactic or ultrasound guidance. Overall, the use of WL was more frequent in patients who had standard (other) markers placed during biopsy as opposed to those with hydrogel markers (HydroMARK). For stereotactic biopsy, 75.8 % of patients with a standard marker required WL versus 17.1 % with HydroMARK and for ultrasound biopsy, 22.6 % standard versus 4.3 % HydroMARK (p < .0001, p < .0001). In some cases where hydrogel markers were used, WL was used for "bracketing" because of the presence of microcalcifications. In cases where standard markers were used, WL was not used because of either IOUS visibility of residual lesion or marker visibility. Specimen volume and re-excision rate were comparable between patients with hydrogel and standard markers, showing no significant differences (p = .1673, p = .1813 respectively). Hydrogel biopsy tissue markers optimize the surgeon's ability to perform a partial mastectomy without the use of WL. HydroMARK was as effective as a standard marker in terms of partial mastectomy specimen volume and re-excision rate. This yields potential for cost savings, increased efficacy in operating room and radiology scheduling, and patient comfort and convenience.
Company, Joseph M.; Roberts, Michael D.; Toedebusch, Ryan G.; Cruthirds, Clayton L.
2013-01-01
The cessation of physical activity in rodents and humans initiates obesogenic mechanisms. The overall purpose of the current study was to determine how the cessation of daily physical activity in rats at 49–56 days of age and at 70–77 days of age via wheel lock (WL) affects adipose tissue characteristics. Male Wistar rats began voluntary running at 28 days old and were either killed at 49–56 days old or at 70–77 days old. Two cohorts of rats always had wheel access (RUN), a second two cohorts of rats had wheel access restricted during the last 7 days (7d-WL), and a third two cohorts of rats did not have access to a voluntary running wheel after the first 6 days of (SED). We observed more robust changes with WL in the 70- to 77-day-old rats. Compared with RUN rats, 7d-WL rats exhibited greater rates of gain in fat mass and percent body fat, increased adipocyte number, higher percentage of small adipocytes, and greater cyclin A1 mRNA in epididymal and perirenal adipose tissue. In contrast, 49- to 56-day-old rats had no change in most of the same characteristics. There was no increase in inflammatory mRNA expression in either cohort with WL. These findings suggest that adipose tissue in 70- to 77-day-old rats is more protected from WL than 49- to 56-day-old rats and responds by expansion via hyperplasia. PMID:24089381
High solids co-digestion of food and landscape waste and the potential for ammonia toxicity.
Drennan, Margaret F; DiStefano, Thomas D
2014-07-01
A pilot-scale study was completed to determine the feasibility of high-solids anaerobic digestion (HSAD) of a mixture of food and landscape wastes at a university in central Pennsylvania (USA). HSAD was stable at low loadings (2g COD/L-day), but developed inhibitory ammonia concentrations at high loadings (15 g COD/L-day). At low loadings, methane yields were 232 L CH4/kg COD fed and 229 L CH4/kg VS fed, and at high loadings yields were 211 L CH4/kg COD fed and 272 L CH4/kg VS fed. Based on characterization and biodegradability studies, food waste appears to be a good candidate for HSAD at low organic loading rates; however, the development of ammonia inhibition at high loading rates suggests that the C:N ratio is too low for use as a single substrate. The relatively low biodegradability of landscape waste as reported herein made it an unsuitable substrate to increase the C:N ratio. Codigestion of food waste with a substrate high in bioavailable carbon is recommended to increase the C:N ratio sufficiently to allow HSAD at loading rates of 15 g COD/L-day. Copyright © 2014 Elsevier Ltd. All rights reserved.
Charfeddine, N; Pérez-Cabal, M A
2017-01-01
The aims of this study were (1) to estimate the phenotypic association between different degrees of severity of claw disorders and production, fertility performance, and longevity in Spanish dairy cattle, and (2) to quantify its economic impact at the animal and herd level. In this study, claw data comprised 108,468 trimmings collected between 2012 and 2014 by 25 trimmers from 804 Holstein dairy herds. The claw disorders considered were the 3 most frequent disorders in Spanish dairy herds: dermatitis (DE), sole ulcer (SU), and white line disease (WL). The presence of SU or WL was associated with a significant decrease in milk production and was more important in cows in second or later lactations. A severe lesion of SU or WL lead to twice the milk losses associated with a mild lesion, ranging from 1.47 to 2.66kg/d of energy-corrected milk. The presence of SU or WL during the early lactation period was associated with more days open, fewer inseminations to get pregnant, and longer calving to first service interval (4.83 and 8.0 d longer due to mild and severe lesions of SU, respectively, and 4.94 and 17.43 d longer due to mild and severe lesions of WL, respectively). The occurrence of a case of SU or WL in first lactation had a significant effect on longevity, with severe lesions reducing up to 71 d of productive life. The cost of a mild lesion ranged from $53 to $232 per affected cow and year, whereas the cost of a severe lesion ranged from $402 to $622 per affected cow and year. The annual costs per cow for DE, SU, and WL were $10.80, $50.9, and $43.2, respectively. An average herd with 64 cows had an extra expenditure of $691/yr due to DE, $3,256/yr due to SU, and $2,765/year due to WL. Milk losses, longer calving intervals, and premature culling contributed to more than half of the costs. Therefore, providing this information to farmers could help decide on strategies to reduce the incidence of claw disorders on the farm. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
Linked color imaging improves the visibility of colorectal polyps: a video study
Yoshida, Naohisa; Naito, Yuji; Murakami, Takaaki; Hirose, Ryohei; Ogiso, Kiyoshi; Inada, Yutaka; Dohi, Osamu; Kamada, Kazuhiro; Uchiyama, Kazuhiko; Handa, Osamu; Konishi, Hideyuki; Siah, Kewin Tien Ho; Yagi, Nobuaki; Fujita, Yasuko; Kishimoto, Mitsuo; Yanagisawa, Akio; Itoh, Yoshito
2017-01-01
Background/study aim Linked color imaging (LCI) by a laser endoscope (Fujifilm Co, Tokyo, Japan) is a novel narrow band light observation. In this study, we aimed to investigate whether LCI could improve the visibility of colorectal polyps using endoscopic videos. Patients and methods We prospectively recorded videos of consecutive polyps 2 – 20 mm in size diagnosed as neoplastic polyps. Three videos, white light (WL), blue laser imaging (BLI)-bright, and LCI, were recorded for each polyp by one expert. After excluding inappropriate videos, all videos were evaluated in random order by two experts and two non-experts according to a published polyp visibility score from four (excellent visibility) to one (poor visibility). Additionally, the relationship between polyp visibility scores in LCI and various clinical characteristics including location, size, histology, morphology, and preparation were analyzed compared to WL and BLI-bright. Results We analyzed 101 colorectal polyps (94 neoplastic) in 66 patients (303 videos). The mean polyp size was 9.0 ± 8.1 mm and 54 polyps were non-polypoid. The mean polyp visibility scores for LCI (2.86 ± 1.08) were significantly higher than for WL and BLI-bright (2.53 ± 1.15, P < 0.001; 2.73 ± 1.47, P < 0.041). The ratio of poor visibility (score 1 and 2) was significantly lower in LCI for experts and non-experts (35.6 %, 33.6 %) compared with WL (49.6 %, P = 0.015, 50.5 %, P = 0.046). The polyp visibility scores for LCI were significantly higher than those for WL for all of the factors. With respect to the comparison between BLI-bright and WL, the polyp visibility scores for BLI-bright were not higher than WL for right-sided location, < 10 mm size, sessile serrated adenoma and polyp histology, and poor preparation. For those characteristics, LCI improved the lesions with right-sided location, SSA/P histology, and poor preparation significantly better than BLI. Conclusions LCI improved polyp visibility compared to WL for both expert and non-expert endoscopists. It is useful for improving polyp visibility in any location, any size, any morphology, any histology, and any preparation level. PMID:28596985
WASTE HANDLING BUILDING ELECTRICAL SYSTEM DESCRIPTION DOCUMENT
DOE Office of Scientific and Technical Information (OSTI.GOV)
S.C. Khamamkar
2000-06-23
The Waste Handling Building Electrical System performs the function of receiving, distributing, transforming, monitoring, and controlling AC and DC power to all waste handling building electrical loads. The system distributes normal electrical power to support all loads that are within the Waste Handling Building (WHB). The system also generates and distributes emergency power to support designated emergency loads within the WHB within specified time limits. The system provides the capability to transfer between normal and emergency power. The system provides emergency power via independent and physically separated distribution feeds from the normal supply. The designated emergency electrical equipment will bemore » designed to operate during and after design basis events (DBEs). The system also provides lighting, grounding, and lightning protection for the Waste Handling Building. The system is located in the Waste Handling Building System. The system consists of a diesel generator, power distribution cables, transformers, switch gear, motor controllers, power panel boards, lighting panel boards, lighting equipment, lightning protection equipment, control cabling, and grounding system. Emergency power is generated with a diesel generator located in a QL-2 structure and connected to the QL-2 bus. The Waste Handling Building Electrical System distributes and controls primary power to acceptable industry standards, and with a dependability compatible with waste handling building reliability objectives for non-safety electrical loads. It also generates and distributes emergency power to the designated emergency loads. The Waste Handling Building Electrical System receives power from the Site Electrical Power System. The primary material handling power interfaces include the Carrier/Cask Handling System, Canister Transfer System, Assembly Transfer System, Waste Package Remediation System, and Disposal Container Handling Systems. The system interfaces with the MGR Operations Monitoring and Control System for supervisory monitoring and control signals. The system interfaces with all facility support loads such as heating, ventilation, and air conditioning, office, fire protection, monitoring and control, safeguards and security, and communications subsystems.« less
DETERMINATION OF OPTIMAL TOXICANT LOADING FOR BIOLOGICAL CLOSURE OF A HAZARDOUS WASTE SITE
Information on Phase I and Phase Il of a multitask effort to achieve biological closure of an abandoned hazardous waste site. aste materials, in the form of buried sludges and lagoon wastes, were examined. ptimal loading levels were evaluated on the basis of biodegradative potent...
The Anopheles (Anopheles) Crucians Subgroup in the United States (Diptera: Culicidae)
1976-01-01
without pale spots except at tip; and LA with 3 dark scaled areas (basally, medially, and apically). The pupa has seta * An illustration is...Beadle, 19, Joplin, 13-1X-1942, A. B. Gurney, 1G. New Jersey: Nixon, 23-VIII-1966, P. H. Thompson, 29; 26-VIII-1966, P, H. Thomp- son , 29; 3P-VIII-1966...IV-1943, La Roth, 1G; Z-IV- 1944, L. Roth, 2WL. Myrtle Beach, 31-x-1943, PWL; 27-VI-1944, La Roth, PWL; lO-VII-1944, L. Roth, lWL; 27-VII-1944, 1WL
Tensile properties of chrome tanned leather waste short fibre filled unsaturated polyester composite
NASA Astrophysics Data System (ADS)
Talib, Satariah; Romli, Ahmad Zafir; Saad, Siti Zaleha
2017-12-01
Waste leather from industries was commonly disposed via land filling or incineration where the oxidation of Cr III to Cr VI by oxidants (such as peroxides and hypohalide) can easily occur. Cr VI is well known as carcinogenic and mutagenic element where the excessive exposure to this element can be very harmful. As an alternative way, the leather waste from footwear industry was utilised as filler in unsaturated polyester composite (UPC). The leather waste was ground using 0.25 mm mesh size and used without any chemical treatment. The sample was fabricated via castingtechnique and the study was carried out at 1 wt%, 2 wt% and 3 wt% filler loading. The leather waste filled composites showed lower tensile strength and Young's modulus than the unfilled composite. The increasing loading amount of leather waste led to the decreased in tensile strength and Young's modulus. The tensile results was supported by the decreasing pattern of density result which indicates the increasing of void content as the filler loading increased. The results of glass transition temperature are also parallel to the tensile properties where the increasing filler loading had decreased the glass transition temperature. Based on the morphological observation on the fractured tensile sample, much severe filler agglomerations and higher amount of voids was observed at higher filler loading compared to the lower filler loading.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sallaberry, Cedric Jean-Marie.; Helton, Jon Craig
2012-10-01
Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high-consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to deactivate the entire system before the SL system fails (i.e., degrades into a configuration that could allowmore » an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). This report describes the Fortran 90 program CPLOAS_2 that implements the following representations for PLOAS for situations in which both link physical properties and link failure properties are time-dependent: (i) failure of all SLs before failure of any WL, (ii) failure of any SL before failure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS can be included in the calculations performed by CPLOAS_2.« less
Determination of body width in brown and white layer pullets by image analyses.
Giersberg, M F; Kemper, N; Hartung, J; Schrader, L; Spindler, B
2017-06-01
1. Specific legal requirements for keeping pullets are not available in the European Union. However, two of the most important rearing factors for pullets are sufficient perching and feeder space. Both factors represent horizontal space dimensions which derive from the body width of the birds. 2. The body width of two strains of layer pullets (brown (BL) and white (WL) layer pullets) based on the measurement of distances in digital images was conducted on front-view digital photographs of BL and WL pullets taken at 8, 12 and 19 weeks of life. 3. Depending on live weight, age and body position, BL pullets measured an average body width between 10.70 ± 1.10 and 13.96 ± 1.11 cm. The width of WL pullets ranged from 10.30 ± 0.86 to 13.00 ± 1.14 cm. 4. Compared with WL, BL pullets occupied more horizontal space during rearing. Age influenced the body width of BL and WL pullets at the end of rearing. The tested body positions of the pullets did not affect the measured body width. 5. The biometric data obtained in this study are a useful basis for developing legal requirements for pullets, especially for defining minimum perch width and feeder space allowances.
Comparison of the chemical composition of dissolved organic matter in three lakes in Minnesota
Cao, Xiaoyan; Aiken, George R.; Butler, Kenna D.; Mao, Jingdong; Schmidt-Rohr, Klaus
2018-01-01
New information on the chemical composition of dissolved organic matter (DOM) in three lakes in Minnesota has been gained from spectral editing and two-dimensional nuclear magnetic resonance (NMR) methods, indicating the effects of lake hydrological settings on DOM composition. Williams Lake (WL), Shingobee Lake (SL), and Manganika Lake (ML) had different source inputs, and the lake water residence time (WRT) of WL was markedly longer than that of SL and ML. The hydrophobic organic acid (HPOA) and transphilic organic acid (TPIA) fractions combined comprised >50% of total DOM in these lakes, and contained carboxyl-rich alicyclic molecules (CRAM), aromatics, carbohydrates, and N-containing compounds. The previously understudied TPIA fractions contained fewer aromatics, more oxygen-rich CRAM, and more N-containing compounds compared to the corresponding HPOA. CRAM represented the predominant component in DOM from all lakes studied, and more so in WL than in SL and ML. Aromatics including lignin residues and phenols decreased in relative abundances from ML to SL and WL. Carbohydrates and N-containing compounds were minor components in both HPOA and TPIA and did not show large variations among the three lakes. The increased relative abundances of CRAM in DOM from ML, SL to WL suggested the selective preservation of CRAM with increased residence time.
Tarhan, Leman; Nakipoğlu, Mahmure; Kavakcıoğlu, Berna; Tongul, Burcu; Nalbantsoy, Ayşe
2016-03-01
The hidromethanolic (Met/W), ethyl acetate (EA(EA/W)), and water (W(EA/W)) extracts from Teucrium sandrasicum leaves (L) and flowers (F) were investigated for antioxidant properties and antiproliferative effects on HeLa, MCF-7, and L929. The highest DPPH scavenging, metal chelating capacities, and total phenolic and flavonoid contents were observed in Met/WL. The highest hydroxyl scavenging and reducing power capacities were found in EA(EA/W)L. Met/WL, EA(EA/W)L and EA(EA/W)F inhibited cancer cell growths, while they did not show significant cytotoxicity on L929. While the reactive oxygen species (ROS) levels were generally close to controls in HeLa, they were induced in MCF-7 with the treatment of Met/WL, EA(EA/W)L, and EA(EA/W)F and acted as antioxidant for L929. The highest apoptosis inductions were observed in Met/WL-treated HeLa and EA(EA/W)L-treated MCF-7, which were supported with the changes in mitochondrial membrane potentials. The highest caspase-9 activities were found in Met/WL-treated HeLa and EA(EA/W)F-treated MCF-7. Caspase-3 activity was only induced in EA(EA/W)F-treated HeLa.
Effect of Food Waste Co-Digestion on Digestion, Dewatering, and Cake Quality.
Higgins, Matthew; Rajagopalan, Ganesh; Miller, Andre; Brown, Jeffrey; Beightol, Steven
2017-01-01
The objective of this study was to evaluate the effect of food waste addition on anaerobic digestion performance as well as downstream parameters including dewatering, cake quality, and filtrate quality. Laboratory-scale digesters were fed processed food waste at rates of 25%, 45%, and 65% increased chemical oxygen demand (COD) loading rates compared to a control fed only primary and secondary solids. The specific methane yield increased from 370 L CH4/kg VSadded for the control to 410, 440, and 470 L CH4/kg VSadded for the 25, 45, and 65% food waste addition, respectively. The cake solids after dewatering were all higher for the food waste digesters compared to the control, with the highest cake solids being measured for the 45% food-waste loading. Compared to the control digester, the biosolids odorant concentration increased for the lowest dose of food waste. Odorant concentrations were below detection for the highest food waste loading.
Peters, James G.; Wilber, W.G.; Crawford, Charles G.; Girardi, F.P.
1979-01-01
A digital computer model calibrated to observe stream conditions was used to evaluate water quality in West Fork Blue River, Washington County, IN. Instream dissolved-oxygen concentration averaged 96.5% of saturation at selected sites on West Fork Blue River during two 24-hour summer surveys. This high dissolved-oxygen concentration reflects small carbonaceous and nitrogenous waste loads; adequate dilution of waste by the stream; and natural reaeration. Nonpoint source waste loads accounted for an average of 53.2% of the total carbonaceous biochemical-oxygen demand and 90.2% of the nitrogenous biochemical-oxygen demand. Waste-load assimilation was studiedfor critical summer and winter low flows. Natural streamflow for these conditions was zero, so no benefit from dilution was provided. The projected stream reaeration capacity was not sufficient to maintain the minimum daily dissolved-oxygen concentration (5 milligrams per liter) in the stream with current waste-discharge restrictions. During winter low flow, ammonia toxicity, rather than dissolved-oxygen concentration, was the limiting water-quality criterion downstream from the Salem wastewater-treatment facility. (USGS)
Miller, Cara C; Burnside, Girvan; Higham, Susan M; Flannigan, Norah L
2016-11-01
To assess the use of Quantitative Light-induced Fluorescence-Digital as an oral hygiene evaluation tool during orthodontic treatment. In this prospective, randomized clinical trial, 33 patients undergoing fixed orthodontic appliance treatment were randomly allocated to receive oral hygiene reinforcement at four consecutive appointments using either white light (WL) or Quantitative Light-induced Fluorescence-Digital (QLF) images, taken with a device, as visual aids. Oral hygiene was recorded assessing the QLF images for demineralization, by fluorescence loss (ΔF), and plaque coverage (ΔR30). A debriefing questionnaire ascertained patient perspectives. There were no significant differences in demineralization (P = .56) or plaque accumulation (P = .82) between the WL and QLF groups from T0 to T4. There was no significant reduction in demineralization, ΔF, in the WL, or the QLF group from T0-T4 (P > .05); however, there was a significant reduction in ΔR30 plaque scores (P < .05). All the participants found being shown the images helpful, with 100% of the QLF group reflecting that it would be useful to have oral hygiene reinforcement for the full duration of treatment compared with 81% of the WL group (OR 2.3; P < .05). Quantitative Light-induced Fluorescence-Digital can be used to detect and monitor demineralization and plaque during orthodontics. Oral hygiene reinforcement at consecutive appointments using WL or QLF images as visual aids is effective in reducing plaque coverage. In terms of clinical benefits, QLF and WL images are of similar effectiveness; however, patients preferred the QLF images.
Biology of two larval morphological phenotypes of Aedes aegypti in Abidjan, Côte d'Ivoire.
Guindo-Coulibaly, N; Diakite, N R; Adja, A M; Coulibaly, J T; Bassa, K F; Konan, Y L; N'Goran, K E
2017-11-23
Since 2008, several outbreaks of yellow fever and dengue occurred in Abidjan, the economic capital of Côte d'Ivoire. A better knowledge of the biology of Aedes aegypti populations, the main vector of yellow fever and dengue viruses, is necessary to tailor vector control strategies implemented in the city. This study was designed to determine some biological parameters, occurring during the life cycle of two morphological phenotypes of Ae. aegypti larvae. Mosquitoes were sampled in a suburb of Abidjan (Treichville) using the WHO layer-traps technique. Biological parameters were studied in laboratory under standard conditions of temperature (27°C ± 2°C) and relative humidity (80% ± 10%). Our results indicated that the mean eggs laid by females from 'brown larvae' (BL) (85.95, 95% confidence interval (CI 95%) 78.87-93.02) was higher than those from 'white larvae' (WL) (64.40%, CI 95% 55.27-73.54). The gonotrophic cycle was 3 and 4 days in females from BL and WL, respectively. The overall yield of breeding mosquitoes from BL (63.88%, CI 95% 62.61-65.14) was higher compared with those of mosquitoes from WL (59.73%, CI 95% 58.35-61.12). The sex ratio (male/female) was 0.95 and 1.68 in Ae. aegypti populations from BL and WL, respectively. Females from BL lived slightly longer than those from WL (t = -2.332; P = 0.021). This study shows that Ae. Aegypti populations from BL and WL present different biological parameters during their life cycle. This could have an implication on their ability to transmit human disease viruses such as dengue and yellow fever. Further molecular studies are needed to determine genetic divergence between these Ae. aegypti populations.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Cheng, X.; Hao, Q.; Ding, M. D.
Two-ribbon brightenings are one of the most remarkable characteristics of an eruptive solar flare and are often used to predict the occurrence of coronal mass ejections (CMEs). Nevertheless, it was recently called into question whether all two-ribbon flares are eruptive. In this paper, we investigate a two-ribbon-like white-light (WL) flare that is associated with a failed magnetic flux rope (MFR) eruption on 2015 January 13, which has no accompanying CME in the WL coronagraph. Observations by the Optical and Near-infrared Solar Eruption Tracer and the Solar Dynamics Observatory reveal that with the increase of the flare emission and the acceleration ofmore » the unsuccessfully erupting MFR, two isolated kernels appear at the WL 3600 Å passband and quickly develop into two elongated ribbon-like structures. The evolution of the WL continuum enhancement is completely coincident in time with the variation of Fermi hard X-ray 26–50 keV flux. An increase of continuum emission is also clearly visible at the whole FUV and NUV passbands observed by the Interface Region Imaging Spectrograph. Moreover, in one WL kernel, the Si iv, C ii, and Mg ii h/k lines display significant enhancement and non-thermal broadening. However, their Doppler velocity pattern is location-dependent. At the strongly bright pixels, these lines exhibit a blueshift, while at moderately bright ones, the lines are generally redshifted. These results show that the failed MFR eruption is also able to produce a two-ribbon flare and high-energy electrons that heat the lower atmosphere, causing the enhancement of the WL and FUV/NUV continuum emissions and chromospheric evaporation.« less
NASA Astrophysics Data System (ADS)
González, D.; Braza, V.; Utrilla, A. D.; Gonzalo, A.; Reyes, D. F.; Ben, T.; Guzman, A.; Hierro, A.; Ulloa, J. M.
2017-10-01
A procedure to quantitatively analyse the relationship between the wetting layer (WL) and the quantum dots (QDs) as a whole in a statistical way is proposed. As we will show in the manuscript, it allows determining, not only the proportion of deposited InAs held in the WL, but also the average In content inside the QDs. First, the amount of InAs deposited is measured for calibration in three different WL structures without QDs by two methodologies: strain mappings in high-resolution transmission electron microscopy images and compositional mappings with ChemiSTEM x-ray energy spectrometry. The area under the average profiles obtained by both methodologies emerges as the best parameter to quantify the amount of InAs in the WL, in agreement with high-resolution x-ray diffraction results. Second, the effect of three different GaAs capping layer (CL) growth rates on the decomposition of the QDs is evaluated. The CL growth rate has a strong influence on the QD volume as well as the WL characteristics. Slower CL growth rates produce an In enrichment of the WL if compared to faster ones, together with a diminution of the QD height. In addition, assuming that the QD density does not change with the different CL growth rates, an estimation of the average In content inside the QDs is given. The high Ga/In intermixing during the decomposition of buried QDs does not only trigger a reduction of the QD height, but above all, a higher impoverishment of the In content inside the QDs, therefore modifying the two most important parameters that determine the optical properties of these structures.
Acupuncture for breast cancer-related lymphedema: a randomized controlled trial.
Bao, Ting; Iris Zhi, Wanqing; Vertosick, Emily A; Li, Qing Susan; DeRito, Janice; Vickers, Andrew; Cassileth, Barrie R; Mao, Jun J; Van Zee, Kimberly J
2018-03-08
Approximately 20% of breast cancer survivors develop breast cancer-related lymphedema (BCRL), and current therapies are limited. We compared acupuncture (AC) to usual care wait-list control (WL) for treatment of persistent BCRL. Women with moderate BCRL lasting greater than six months were randomized to AC or WL. AC included twice weekly manual acupuncture over six weeks. We evaluated the difference in circumference and bioimpedance between affected and unaffected arms. Responders were defined as having a decrease in arm circumference difference greater than 30% from baseline. We used analysis of covariance for circumference and bioimpedance measurements and Fisher's exact to determine the proportion of responders. Among 82 patients, 73 (89%) were evaluable for the primary endpoint (36 in AC, 37 in WL). 79 (96%) patients received lymphedema treatment before enrolling in our study; 67 (82%) underwent ongoing treatment during the trial. We found no significant difference between groups for arm circumference difference (0.38 cm greater reduction in AC vs. WL, 95% CI - 0.12 to 0.89, p = 0.14) or bioimpedance difference (1.06 greater reduction in AC vs. WL, 95% CI - 5.72 to 7.85, p = 0.8). There was also no difference in the proportion of responders: 17% AC versus 11% WL (6% difference, 95% CI - 10 to 22%, p = 0.5). No severe adverse events were reported. Our acupuncture protocol appeared to be safe and well tolerated. However, it did not significantly reduce BCRL in pretreated patients receiving concurrent lymphedema treatment. This regimen does not improve upon conventional lymphedema treatment for breast cancer survivors with persistent BCRL.
Larson, James H; Maki, Ryan P; Vondra, Benjamin A; Peterson, Kevin E
2018-01-01
Water level (WL) fluctuations in lakes influence many aspects of ecosystem processes. Concern about the potential impact of WL fluctuations on fisheries was one of the factors that motivated the decision in 2000 to alter the management of WL in the Rainy-Namakan reservoir complex (on the border between the U.S. state of Minnesota and the Canadian province of Ontario). We used a Before-After, Control-Impact (BACI) framework to identify potential impacts of the change in WL management to Walleye, Northern Pike and Yellow Perch catch per unit effort (CPUE). The CPUE of these species from 1990-1999 and from 2005-2014 were compared in four impact lakes (Lake Kabetogama, Namakan Lake, Rainy Lake and Sand Point Lake) and two control lakes (Lake of the Woods and Lake Vermilion) using a simple Bayesian model. Changes in fish CPUE in the impact lakes were often similar to changes that occurred in at least one control lake. The only change that was not similar to changes in control lakes was an increase of Yellow Perch in Lake Kabetogama. The two control lakes often differed substantially from each other, such that if only one had been available our conclusions about the role of WL management on fisheries would be very different. In general, identifying cause-and-effect relationships in observational field data is very difficult, and the BACI analysis used here does not specify a causative mechanism, so co-occurring environmental and management changes may obscure the effect of WL management.
Wong, Ee-Lynn; Tnay, Jessie Koh-Sing
2018-01-01
Background Female condom (FC) has been available for over 30 years, but it still lacks wide acceptability. To overcome misdirection and invagination occurring in FC and to provide a wider area of protection, Wondaleaf® (WL), a new-generation adhesive FC, was recently invented. This pioneering study sought to assess the acceptability and functional performance of WL among Malaysian women. Methods A mixed method survey was conducted in three cities of Malaysia, recruiting sexually active heterosexual women, aged 18–50, by snowball sampling method. Participants were provided with WL and initially surveyed to rate its performance in five coital usages over 2 months. After that, the participants underwent a second survey to rate their satisfaction and acceptability toward WL. Descriptive statistics on clinical failure rates were tabulated with correlational analysis performed to identify major variables contributing to WL’s functional performance and acceptability. Results Out of the 51 enrolled participants, 31 women completed the required surveys. WL’s total clinical failure rate was 2.60% (out of 155 condom uses) with above-average ratings of functional performance. The ease of use significantly correlated with ratings of no slippage and no misdirection. The confidence in WL’s safety features significantly correlated with a sense of empowerment and protection. Conclusion WL has a relatively low risk of clinical failures and an overall favorable acceptability among Malaysian women. However, this study also showed that its future usage largely depends on partner acceptability. It may have the potential of complementing the existing barrier toward contraceptive use. Further studies are needed to understand the global acceptability of WL. PMID:29440937
Impact of a primordial magnetic field on cosmic microwave background B modes with weak lensing
NASA Astrophysics Data System (ADS)
Yamazaki, Dai G.
2018-05-01
We discuss the manner in which the primordial magnetic field (PMF) suppresses the cosmic microwave background (CMB) B mode due to the weak-lensing (WL) effect. The WL effect depends on the lensing potential (LP) caused by matter perturbations, the distribution of which at cosmological scales is given by the matter power spectrum (MPS). Therefore, the WL effect on the CMB B mode is affected by the MPS. Considering the effect of the ensemble average energy density of the PMF, which we call "the background PMF," on the MPS, the amplitude of MPS is suppressed in the wave number range of k >0.01 h Mpc-1 . The MPS affects the LP and the WL effect in the CMB B mode; however, the PMF can damp this effect. Previous studies of the CMB B mode with the PMF have only considered the vector and tensor modes. These modes boost the CMB B mode in the multipole range of ℓ>1000 , whereas the background PMF damps the CMB B mode owing to the WL effect in the entire multipole range. The matter density in the Universe controls the WL effect. Therefore, when we constrain the PMF and the matter density parameters from cosmological observational data sets, including the CMB B mode, we expect degeneracy between these parameters. The CMB B mode also provides important information on the background gravitational waves, inflation theory, matter density fluctuations, and the structure formations at the cosmological scale through the cosmological parameter search. If we study these topics and correctly constrain the cosmological parameters from cosmological observations, including the CMB B mode, we need to correctly consider the background PMF.
Sala, Isabel; Illán-Gala, Ignacio; Alcolea, Daniel; Sánchez-Saudinós, Ma Belén; Salgado, Sergio Andrés; Morenas-Rodríguez, Estrella; Subirana, Andrea; Videla, Laura; Clarimón, Jordi; Carmona-Iragui, María; Ribosa-Nogué, Roser; Blesa, Rafael; Fortea, Juan; Lleó, Alberto
2017-01-01
Episodic memory impairment is the core feature of typical Alzheimer's disease. To evaluate the performance of two commonly used verbal memory tests to detect mild cognitive impairment due to Alzheimer's disease (MCI-AD) and to predict progression to Alzheimer's disease dementia (AD-d). Prospective study of MCI patients in a tertiary memory disorder unit. Patients underwent an extensive neuropsychological battery including two tests of declarative verbal memory: The Free and Cued Selective Reminding Test (FCSRT) and the word list learning task from the Consortium to Establish a Registry for Alzheimer's disease (CERAD-WL). Cerebrospinal fluid (CSF) was obtained from all patients and MCI-AD was defined by means of the t-Tau/Aβ1-42 ratio. Logistic regression analyses tested whether the combination of FCSRT and CERAD-WL measures significantly improved the prediction of MCI-AD. Progression to AD-d was analyzed in a Cox regression model. A total of 202 MCI patients with a mean follow-up of 34.2±24.2 months were included and 98 (48.5%) met the criteria for MCI-AD. The combination of FCSRT and CERAD-WL measures improved MCI-AD classification accuracy based on CSF biomarkers. Both tests yielded similar global predictive values (59.9-65.3% and 59.4-62.8% for FCSRT and CERAD-WL, respectively). MCI-AD patients with deficits in both FCSRT and CERAD-WL had a faster progression to AD-d than patients with deficits in only one test. The combination of FCSRT and CERAD-WL improves the classification of MCI-AD and defines different prognostic profiles. These findings have important implications for clinical practice and the design of clinical trials.
Lensch, D; Schaum, C; Cornel, P
2016-01-01
Many digesters in Germany are not operated at full capacity; this offers the opportunity for co-digestion. Within this research the potentials and limits of a flexible and adapted sludge treatment are examined with a focus on the digestion process with added food waste as co-substrate. In parallel, energy data from a municipal wastewater treatment plant (WWTP) are analysed and lab-scale semi-continuous and batch digestion tests are conducted. Within the digestion tests, the ratio of sewage sludge to co-substrate was varied. The final methane yields show the high potential of food waste: the higher the amount of food waste the higher the final yield. However, the conversion rates directly after charging demonstrate better results by charging 10% food waste instead of 20%. Finally, these results are merged with the energy data from the WWTP. As an illustration, the load required to cover base loads as well as peak loads for typical daily variations of the plant's energy demand are calculated. It was found that 735 m³ raw sludge and 73 m³ of a mixture of raw sludge and food waste is required to cover 100% of the base load and 95% of the peak load.
ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT--BAGHOUSE FILTRATION PRODUCTS, W.L. GORE ASSOC., INC.
The U.S. Environmental Protection Agency Air Pollution Control Technology (APCT) Verification Center evaluates the performance of baghouse filtration products used primarily to control PM2.5 emissions. This verification statement summarizes the test results for W.L. Gore & Assoc....
NASA Astrophysics Data System (ADS)
Ortega, Luis Humberto
The Advanced Fuel Cycle Initiative (AFCI) is a Department of Energy (DOE) program, that has been investigating technologies to improve fuel cycle sustainability and proliferation resistance. One of the program's goals is to reduce the amount of radioactive waste requiring repository disposal. Cesium and strontium are two primary heat sources during the first 300 years of spent nuclear fuel's decay, specifically isotopes Cs-137 and Sr-90. Removal of these isotopes from spent nuclear fuel will reduce the activity of the bulk spent fuel, reducing the heat given off by the waste. Once the cesium and strontium are separated from the bulk of the spent nuclear fuel, the isotopes must be immobilized. This study is focused on a method to immobilize a cesium- and strontium-bearing radioactive liquid waste stream. While there are various schemes to remove these isotopes from spent fuel, this study has focused on a nitric acid based liquid waste. The waste liquid was mixed with the bentonite, dried then sintered. To be effective sintering temperatures from 1100 to 1200°C were required, and waste concentrations must be at least 25 wt%. The product is a leach resistant ceramic solid with the waste elements embedded within alumino-silicates and a silicon rich phase. The cesium is primarily incorporated into pollucite and the strontium into a monoclinic feldspar. The simulated waste was prepared from nitrate salts of stable ions. These ions were limited to cesium, strontium, barium and rubidium. Barium and rubidium will be co-extracted during separation due to similar chemical properties to cesium and strontium. The waste liquid was added to the bentonite clay incrementally with drying steps between each addition. The dry powder was pressed and then sintered at various temperatures. The maximum loading tested is 32 wt. percent waste, which refers to 13.9 wt. percent cesium, 12.2 wt. percent barium, 4.1 wt. percent strontium, and 2.0 wt. percent rubidium. Lower loadings of waste were also tested. The final solid product was a hard dense ceramic with a density that varied from 2.12 g/cm3 for a 19% waste loading with a 1200°C sintering temperature to 3.03 g/cm 3 with a 29% waste loading and sintered at 1100°C. Differential Scanning Calorimetry and Thermal Gravimetric Analysis (DSC-TGA) of the loaded bentonite displayed mass loss steps which were consistent with water losses in pure bentonite. Water losses were complete after dehydroxylation at ˜650°C. No mass losses were evident beyond the dehydroxylation. The ceramic melts at temperatures greater than 1300°C. Light flash analysis found heat capacities of the ceramic to be comparable to those of strontium and barium feldspars as well as pollucite. Thermal conductivity improved with higher sintering temperatures, attributed to lower porosity. Porosity was minimized in 1200°C sinterings. Ceramics with waste loadings less than 25 wt% displayed slump, the lowest waste loading, 15 wt% bloated at a 1200°C sintering. Waste loading above 25 wt% produced smooth uniform ceramics when sintered >1100°C. Sintered bentonite may provide a simple alternative to vitrification and other engineered radioactive waste-forms.
Von Thun, Nancy L; Sukumar, Deeptha; Heymsfield, Steven B; Shapses, Sue A
2014-05-01
Short-term weight loss is accompanied by bone loss in postmenopausal women. The longer-term impact of weight loss on bone in reduced overweight/obese women compared with women who regained their weight was examined in this study using a case-control design. Postmenopausal women (N = 42; mean [SD] body mass index, 28.3 [2.8] kg/m; mean [SD] age, 60.7 [5.5] y) were recruited 2 years after the start of a 6-month weight loss trial; those who maintained their weight (weight loss maintainer [WL-M] group) were matched to a cohort of women who regained their weight (weight loss regainer [WL-R] group). Serum hormones and bone markers were measured in a subset. Bone mineral density (BMD) at the femoral neck, trochanter, spine, radius, and total body, and soft-tissue composition were taken at baseline, 0.5 years, and 2 years. During weight loss, both groups lost 9.3% (3.4%) of body weight, with no significant difference between the groups. After weight loss, weight change was -0.1% (2.7%) and 6.0% (3.3%) in the WL-M (n = 22) and WL-R (n = 20) groups, respectively. After 2 years, both groups lost BMD at the femoral neck and trochanter (P ≤ 0.01), whereas only the WL-M group reduced BMD at the 1/3 radius (P < 0.001). There was greater BMD loss at the trochanter (-6.8% [5.7%]) and 1/3 radius (-4.5% [3.3%]) in the WL-M group compared with the WL-R group after 2 years. Multiple linear regression showed that change in leg fat mass (but not trunk fat) contributed to trochanter BMD loss (P < 0.05). After 2 years, there is no BMD recovery of weight reduction-induced bone loss, irrespective of weight regain. These data suggest that the period after weight loss may be an important point in time to prevent bone loss for those who maintain weight and those who regain weight.
Ito, Eiki; Murata, Akira; Yamamoto, Kazuo; Kudo, Shoji
2003-04-01
We evaluated body weight loss and growth hormone secretion in patients with sleep-disordered breathing associated with chronic obstructive pulmonary disease. Of 11 patients hospitalized for pulmonary rehabilitation, five (WL group) had a history of body weight loss within two years before their interviews, while the other 6 patients (NWL group) had no changes in body weight. All patients underwent body index measurements, pulmonary function tests, blood gas analyses, assessments of nutritional status, and full night polysomnography for two consecutive days. Growth hormone levels were measured in the first 3-hour period following falling asleep. There were no significant inter-group differences between the results of pulmonary function tests, blood gas analyses, or nutritional status assessment. The WL group had a significantly higher percentage loss of body weight than the NWL group (mean +/- S.D. 11.5 +/- 4.7% in the WL group versus 2.7 +/- 1.8% in the NWL group, p < 0.01). The WL group had a significantly higher sleep apnea/hypopnea index than the NWL group (42.4 +/- 9.5/hr in the WL group versus 7.8 +/- 2.9/hr in the NWL group, p < 0.01). The WL group showed a higher rate of stage I + II sleep than the NWL group (84.9 +/- 7.0% versus 64.5 +/- 8.7%), with lower rates of slow wave sleep (2.2 +/- 2.1% versus 15.0 +/- 8.7%) and rapid eye movement sleep (12.9 +/- 6.3% versus 20.6 +/- 1.0%). The WL group showed a low level of growth hormone secretion with no peak in the sequential curve, but had a higher level of insulin growth factor-1 than the NWL group (148 +/- 36 ng/ml versus 90 +/- 22 ng/ml, p < 0.01). These results suggest that chronic obstructive pulmonary disease patients undergoing weight loss are likely to have an increase of growth hormone secretions in the daytime, possibly induced by underlying psychiatric disorders such as depression. Patients with chronic obstructive pulmonary disease may lose weight regardless of nutritional status because of a disturbance of growth hormone secretion resulting of sleep-disordered breathing.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ebert, W. L.; Snyder, C. T.; Frank, Steven
This report describes the scientific basis underlying the approach being followed to design and develop “advanced” glass-bonded sodalite ceramic waste form (ACWF) materials that can (1) accommodate higher salt waste loadings than the waste form developed in the 1990s for EBR-II waste salt and (2) provide greater flexibility for immobilizing extreme waste salt compositions. This is accomplished by using a binder glass having a much higher Na 2O content than glass compositions used previously to provide enough Na+ to react with all of the Cl– in the waste salt and generate the maximum amount of sodalite. The phase compositions andmore » degradation behaviors of prototype ACWF products that were made using five new binder glass formulations and with 11-14 mass% representative LiCl/KCl-based salt waste were evaluated and compared with results of similar tests run with CWF products made using the original binder glass with 8 mass% of the same salt to demonstrate the approach and select a composition for further studies. About twice the amount of sodalite was generated in all ACWF materials and the microstructures and degradation behaviors confirmed our understanding of the reactions occurring during waste form production and the efficacy of the approach. However, the porosities of the resulting ACWF materials were higher than is desired. These results indicate the capacity of these ACWF waste forms to accommodate LiCl/KCl-based salt wastes becomes limited by porosity due to the low glass-to-sodalite volume ratio. Three of the new binder glass compositions were acceptable and there is no benefit to further increasing the Na content as initially planned. Instead, further studies are needed to develop and evaluate alternative production methods to decrease the porosity, such as by increasing the amount of binder glass in the formulation or by processing waste forms in a hot isostatic press. Increasing the amount of binder glass to eliminate porosity will decrease the waste loading from about 12% to 10% on a mass basis, but this will not significantly impact the waste loading on a volume basis. It is likely that heat output will limit the amount of waste salt that can be accommodated in a waste canister rather than the salt loading in an ACWF, and that the increase from 8 mass% to about 10 mass% salt loadings in ACWF materials will be sufficient to optimize these waste forms. Although the waste salt composition used in this study contained a moderate amount of NaCl, the test results suggest waste salts with little or no NaCl can be accommodated in ACWF materials by using the new binder glass, albeit at waste loadings lower than 8 mass%. The higher glass contents that will be required for ACWF materials made with salt wastes that do not contain NaCl are expected to result in much lower porosities in those waste forms.« less
NASA Astrophysics Data System (ADS)
Wang, Wei-Hsiang; Lyu, Syue-Ru; Heredia, Elica; Liu, Shu-Hao; Jiang, Pei-hsun; Liao, Po-Yung; Chang, Ting-Chang
2017-05-01
We investigate the gate-voltage dependence of the magnetoconductivity of several amorphous InGaZnO4 (a-IGZO) thin-film transistors (TFTs). The magnetoconductivity exhibits gate-voltage-controlled competitions between weak localization (WL) and weak antilocalization (WAL), and the respective weights of WL and WAL contributions demonstrate an intriguing universal dependence on the channel conductivity regardless of the difference in the electrical characteristics of the a-IGZO TFTs. Our findings help build a theoretical interpretation of the competing WL and WAL observed in the electron systems in a-IGZO TFTs.
Microstructural Investigation of a Wark-Lovering Rim on a Vigarano CAI
NASA Technical Reports Server (NTRS)
Han, J.; Keller, L. P.; Needham, A. W.; Messenger, S.; Simon, J. I.
2015-01-01
Wark-Lovering (WL) rims are thin multi-layered mineral sequences that surround many CAIs. These rim layers consist of the primary minerals found in the CAI interiors, but vary in their mineralogy. Several models for their origin have been proposed including condensation, reaction with a nebular gas, evaporation, or combinations of these. However, there still is little consensus on how and when the rims formed. Here, we describe the microstructure and mineralogy of a WL rim on a type B CAI from the Vigarano CV(sub red) chondrite using FIB/TEM to better understand the astrophysical significance of WL rim formation.
Biochemical and developmental characterization of carbonic anhydrase II from chicken erythrocytes.
Nishita, Toshiho; Tomita, Yuichiro; Imanari, Takao; Ichihara, Nobutsune; Orito, Kensuke; Arishima, Kazuyoshi
2011-03-07
Carbonic anhydrase (CA) of the chicken has attracted attention for a long time because it has an important role in the eggshell formation. The developmental profile of CA-II isozyme levels in chicken erythrocytes has not been determined or reported. Furthermore, the relations with CA-II in erythrocyte and egg production are not discussed. In the present study, we isolated CA-II from erythrocytes of chickens and determined age-related changes of CA-II levels in erythrocytes. Chicken CA-II was purified by a combination of column chromatography. The levels of CA-II in the hemolysate of the chicken were determined using the ELISA system in blood samples from 279 female chickens, ages 1 to 93 weeks, 69 male chickens, ages 3 to 59 weeks and 52 weeks female Araucana-chickens. The mean concentration of CA-II in hemolysate from 1-week-old female was 50.8 ± 11.9 mg/g of Hb. The mean levels of CA-II in 25-week-old (188.1 ± 82.6 mg/g of Hb), 31-week-old (193.6 ± 69.7 mg/g of Hb) and 49-week-old (203.8 ± 123.5 mg/g of Hb) female-chickens showed the highest level of CA-II. The levels of CA-II in female WL-chickens significantly decreased at 63 week (139.0 ± 19.3 mg/g of Hb). The levels of CA-II in female WL-chicken did not change from week 63 until week 93.The mean level of CA-II in hemolysate of 3-week-old male WL-chickens was 78.3 ± 20.7 mg/g of Hb. The levels of CA-II in male WL-chickens did not show changes in the week 3 to week 59 timeframe. The mean level of CA-II in 53-week-old female Araucana-chickens was 23.4 ± 1.78 mg/g of Hb. These levels of CA-II were about 11% of those of 49-week-old female WL-chickens. Simple linear regression analysis showed significant associations between the level of CA-II and egg laying rate from 16 week-old at 63 week-old WL-chicken (p<0.01). Developmental changes and sexual differences of CA-II concentration in WL-chicken erythrocytes were observed. The concentration of CA-II in the erythrocyte of WL-chicken was much higher than that in Araucana-chicken (p<0.01). © 2011 Nishita et al; licensee BioMed Central Ltd.
McCormack, L; Gadano, A; Lendoire, J; Imventarza, O; Andriani, O; Gil, O; Toselli, L; Bisigniano, L; de Santibañes, E
2010-09-01
In July 2005, Argentina was the first country after the United States to adopt the MELD system. The purpose of the present study was to analyse the impact of this new system on the adult liver waiting list (WL). Between 2005 and 2009, 1773 adult patients were listed for liver transplantation: 150 emergencies and 1623 electives. Elective patients were categorized using the MELD system. A prospective database was used to analyse mortality and probability to be transplanted (PTBT) on the WL. The waiting time increased inversely with the MELD score and PTBT positively correlated with MELD score. With scores >/= 18 the PTBT remained over 50%. However, the largest MELD subgroup with <10 points (n = 433) had the lower PTBT (3%). In contrast, patients with T(2) hepatocellular carcinoma benefited excessively with the highest PTBT (84.2%) and the lowest mortality rate (5.4%). The WL mortality increased after MELD adoption (10% vs. 14.8% vs. P < 0.01). Patients with <10 MELD points had >fourfold probability of dying on the WL than PTBT (14.3% vs. 3%; P < 0.0001). After MELD implementation, WL mortality increased and most patients who died had a low MELD score. A comprehensive revision of the MELD system must be performed to include cultural and socio-economical variables that could affect each country individually.
Can Flare Loops Contribute to the White-light Emission of Stellar Superflares?
NASA Astrophysics Data System (ADS)
Heinzel, P.; Shibata, K.
2018-06-01
Since the discovery of stellar superflares by the Kepler satellite, these extremely energetic events have been studied in analogy to solar flares. Their white-light (WL) continuum emission has been interpreted as being produced by heated ribbons. In this paper, we compute the WL emission from overlying flare loops depending on their density and temperature and show that, under conditions expected during superflares, the continuum brightening due to extended loop arcades can significantly contribute to stellar flux detected by Kepler. This requires electron densities in the loops of 1012‑1013 cm‑3 or higher. We show that such densities, exceeding those typically present in solar-flare loops, can be reached on M-dwarf and solar-type superflare stars with large starspots and much stronger magnetic fields. Quite importantly, the WL radiation of loops is not very sensitive to their temperature and thus both cool as well as hot loops may contribute. We show that the WL intensity emergent from optically thin loops is lower than the blackbody radiation from flare ribbons, but the contribution of loops to total stellar flux can be quite important due to their significant emitting areas. This new scenario for interpreting superflare emission suggests that the observed WL flux is due to a mixture of the ribbon and loop radiation and can be even loop-dominated during the gradual phase of superflares.
NASA Astrophysics Data System (ADS)
Li, S. S.; Wang, S.; Yan, W.
2016-08-01
When methyl tert-butyl ether (MTBE) is added as oxygenates it increases the octane number and decreases the release of nitric oxide from the incomplete combustion of reformulated gasoline. The extensive use of MTBE allowed it to be detectable as a pollutant in both ground-level and underground water worldwide. The present study focuses on the isolation and characterization of MTB-degrading microorganisms by cometabolism based on the results of growth on different carbon sources. It also focuses on the kinetic analysis and the continuous degradation of MTBE. A bacterial strain WL1 that can grow on both n-alkanes (C5-C8) and aromatics was isolated and named Pseudomonas sp. WL1 according to the 16S rDNA sequencing analysis. Strain WL1 could cometabolically degrade MTBE in the presence of n-alkanes with a desirable degradation rate. Diverse n-alkanes with different lengths of carbon chains showed significant influence on the degradation rate of MTBE and accumulation of tert-butyl alcohol (TBA). When strain WL1 cometabolically degraded MTBE in the presence of n-pentane, higher MTBE-degrading rate and lower TBA-accumulation were observed (Vmax = 38.1 nmol/min/mgprotei, Ks = 6.8 mmol/L). In the continuous degrading experiment, the removal efficiency of MTBE by Pseudomonas sp. WL1 did not show any obvious decrease after five subsequent additions.
Perceptions of Barriers to Effective Obesity Care: Results from the National ACTION Study.
Kaplan, Lee M; Golden, Angela; Jinnett, Kimberly; Kolotkin, Ronette L; Kyle, Theodore K; Look, Michelle; Nadglowski, Joseph; O'Neil, Patrick M; Parry, Thomas; Tomaszewski, Kenneth J; Stevenin, Boris; Lilleøre, Søren Kruse; Dhurandhar, Nikhil V
2018-01-01
ACTION (Awareness, Care, and Treatment in Obesity maNagement) examined obesity-related perceptions, attitudes, and behaviors among people with obesity (PwO), health care providers (HCPs), and employer representatives (ERs). A total of 3,008 adult PwO (BMI ≥ 30 by self-reported height and weight), 606 HCPs, and 153 ERs completed surveys in a cross-sectional design. Despite several weight loss (WL) attempts, only 23% of PwO reported 10% WL during the previous 3 years. Many PwO (65%) recognized obesity as a disease, but only 54% worried their weight may affect future health. Most PwO (82%) felt "completely" responsible for WL; 72% of HCPs felt responsible for contributing to WL efforts; few ERs (18%) felt even partially responsible. Only 50% of PwO saw themselves as "obese," and 55% reported receiving a formal diagnosis of obesity. Despite HCPs' reported comfort with weight-related conversations, time constraints deprioritized these efforts. Only 24% of PwO had a scheduled follow-up to initial weight-related conversations. Few PwO (17%) perceived employer-sponsored wellness offerings as helpful in supporting WL. Although generally perceived as a disease, obesity is not commonly treated as such. Divergence in perceptions and attitudes potentially hinders better management. This study highlights inconsistent understanding of the impact of obesity and need for both self-directed and medical management. © 2017 The Obesity Society.
Aboud, Katherine S.; Bailey, Stephen K.; Petrill, Stephen A.; Cutting, Laurie E.
2016-01-01
Skilled reading depends on recognizing words efficiently in isolation (word-level processing; WL) and extracting meaning from text (discourse-level processing; DL); deficiencies in either result in poor reading. FMRI has revealed consistent overlapping networks in word and passage reading, as well as unique regions for DL processing, however less is known about how WL and DL processes interact. Here we examined functional connectivity from seed regions derived from where BOLD signal overlapped during word and passage reading in 38 adolescents ranging in reading ability, hypothesizing that even though certain regions support word- and higher-level language, connectivity patterns from overlapping regions would be task modulated. Results indeed revealed that the left-lateralized semantic and working memory (WM) seed regions showed task-dependent functional connectivity patterns: during DL processes, semantic and WM nodes all correlated with the left angular gyrus, a region implicated in semantic memory/coherence building. In contrast, during WL, these nodes coordinated with a traditional WL area (left occipitotemporal region). Additionally, these WL and DL findings were modulated by decoding and comprehension abilities, respectively, with poorer abilities correlating with decreased connectivity. Findings indicate that key regions may uniquely contribute to multiple levels of reading; we speculate that these connectivity patterns may be especially salient for reading outcomes and intervention response. PMID:27147257
Cao, Xiaohuang; Zhang, Min; Mujumdar, Arun S; Zhong, Qifeng; Wang, Zhushang
2018-01-01
Barley grass is a plant resource for rehabilitation therapy. Its processing requires retaining nutrition well for rehabilitation cure of consumers. To meet the aim as well as low energy consumption and microbiological safety of products, ultrasonic treatments (UT) were applied to bathing materials at different power levels (10, 30, 45, 60W/L) for 10mins. After treatments, the bathed barley grass (100g) was freeze-dried under vacuum -0.09MPa with fixed power of 2W/g. Parameters of color, microbial colony, energy consumption, glass transition temperature, moisture content, water activity, taste substances, contents of flavonoid and chlorophyll were determined after drying. In contrast with no treatment case, UT (45W/L) decreased drying time by 14% and decreased energy consumption by 19%; UT (60W/L) decreased total microbial colonies by 33%. Also, UT (30W/L) yielded contents of flavonoid (9.2/kg) and chlorophyll (10.5g/kg) of dried sample; UT power (10W/L) yielded the highest L ∗ (51.5) and the lowest a ∗ (-9.3) value. Simultaneously, UT leads to a higher glass transition temperature (Tg), lower water activity and produces less sourness and bitterness of dried products. Ultra-sonication is an alternative to improve quality, flavor and energy consumption of barley grass in freeze drying. Copyright © 2017 Elsevier B.V. All rights reserved.
NASA Astrophysics Data System (ADS)
Dyl, K. A.; Young, E. D.
2009-12-01
We define the reaction space that controls changes in pyroxene composition in CAIs and Wark-Lovering (WL) rims in an oxidizing solar nebula. Ti-rich pyroxenes in CAIs record a sub-solar oxygen fugacity (Ti3+/Ti4+~1.5). WL rim pyroxenes in the CAI Leoville 144A have a distinctly lower oxidation state.This difference supports WL rim condensation in an environment of increasing O2(g) and Mg(g) (Simon et al. 2005). We used the following phase components to identify four linearly independent reactions (Thompson 1982): diopside, CaTs (Al2Mg-1Si-1), T3 (Ti3+AlMg-1Si-1), T4 (Ti4+Al2Mg-1Si-2), En (MgCa-1), perovskite, O(g), Mg(g), SiO(g), and Ca(g). Compositional variation in this system is dominated by two reactions. The first is oxidation of Ti3+ via reaction with O and Mg in the gas phase: 1.5 O(g) + Mg(g) → ¼ Di + [Ti4+Mg3/4Ti3+-1Ca-1/4Si-1/2] (1). Pyroxene is produced and En is introduced. The second reaction (2) is perovskite formation. It is observed in the WL rim of Leoville 144A, and experiments confirm that an elevated Ti component converts pyroxene to perovskite(Gupta et al. 1973). MgCa-1 is the third linearly independent reaction (3). They combine to give: ½ Di + x Ca(g)→ x Mg(g)+ Pv + [Mg1/2-xSiTi4+-1Ca-1/2+x](2,3). Unlike (1), pyroxene is consumed in this reaction. The parameter x defines the extent of Mg-Ca exchange. When x > 0.5, WL rim formation occurs in an environment where Mg is volatile and Ca condenses. The reaction space defined by reactions (1) and (2,3) describes the transition from CAI interior to WL rims. WL rim pyroxene Ti contents, [CaTs], and Ca < 1 pfu are all explained in this space. The fourth linearly independent reaction is SiO(g):1/8 Di + ¼ Mg(g)→ ¾ SiO(g) + [Mg3/8Ca1/8Ti4+Ti3+-1Si-1/2](4). Silica reduction forms Ti4+, releasing SiO(g). (4) does not describe the oxidation of Ti3+ in WL rim pyroxene, but (1) - (4) results in En formation directly from the gas phase. This may explain WL rim analyses that have Si contents in excess of those predicted from reactions (1) and (2,3). Simon et al. (2005) EPSL 41, 272-283; Thompson (1982)Rev. Min. 10, 33-52; Gupta et al. (1973) Contr. Mineral. Petrol. 41, 333-344 Reaction space for CAI pyroxene. Pyroxenes plotted using titanium contents.
Removal of radioactive and other hazardous material from fluid waste
Tranter, Troy J [Idaho Falls, ID; Knecht, Dieter A [Idaho Falls, ID; Todd, Terry A [Aberdeen, ID; Burchfield, Larry A [W. Richland, WA; Anshits, Alexander G [Krasnoyarsk, RU; Vereshchagina, Tatiana [Krasnoyarsk, RU; Tretyakov, Alexander A [Zheleznogorsk, RU; Aloy, Albert S [St. Petersburg, RU; Sapozhnikova, Natalia V [St. Petersburg, RU
2006-10-03
Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.
Shamim, Saquib; Mahapatra, S; Scappucci, G; Klesse, W M; Simmons, M Y; Ghosh, Arindam
2017-05-04
We report quantum transport measurements on two dimensional (2D) Si:P and Ge:P δ-layers and compare the inelastic scattering rates relevant for weak localization (WL) and universal conductance fluctuations (UCF) for devices of various doping densities (0.3-2.5 × 10 18 m -2 ) at low temperatures (0.3-4.2 K). The phase breaking rate extracted experimentally from measurements of WL correction to conductivity and UCF agree well with each other within the entire temperature range. This establishes that WL and UCF, being the outcome of quantum interference phenomena, are governed by the same dephasing rate.
Dynamic waste management (DWM): towards an evolutionary decision-making approach.
Rojo, Gabriel; Glaus, Mathias; Laforest, Valerie; Laforest, Valérie; Bourgois, Jacques; Bourgeois, Jacques; Hausler, Robert
2013-12-01
To guarantee sustainable and dynamic waste management, the dynamic waste management approach (DWM) suggests an evolutionary new approach that maintains a constant flow towards the most favourable waste treatment processes (facilities) within a system. To that end, DWM is based on the law of conservation of energy, which allows the balancing of a network, while considering the constraints of incoming (h1 ) and outgoing (h2 ) loads, as well as the distribution network (ΔH) characteristics. The developed approach lies on the identification of the prioritization index (PI) for waste generators (analogy to h1 ), a global allocation index for each of the treatment processes (analogy to h2 ) and the linear index load loss (ΔH) associated with waste transport. To demonstrate the scope of DWM, we outline this approach, and then present an example of its application. The case study shows that the variable monthly waste from the three considered sources is dynamically distributed in priority to the more favourable processes. Moreover, the reserve (stock) helps temporarily store waste in order to ease the global load of the network and favour a constant feeding of the treatment processes. The DWM approach serves as a decision-making tool by evaluating new waste treatment processes, as well as their location and new means of transport for waste.
Mocking the weak lensing universe: The LensTools Python computing package
NASA Astrophysics Data System (ADS)
Petri, A.
2016-10-01
We present a newly developed software package which implements a wide range of routines frequently used in Weak Gravitational Lensing (WL). With the continuously increasing size of the WL scientific community we feel that easy to use Application Program Interfaces (APIs) for common calculations are a necessity to ensure efficiency and coordination across different working groups. Coupled with existing open source codes, such as CAMB (Lewis et al., 2000) and Gadget2 (Springel, 2005), LensTools brings together a cosmic shear simulation pipeline which, complemented with a variety of WL feature measurement tools and parameter sampling routines, provides easy access to the numerics for theoretical studies of WL as well as for experiment forecasts. Being implemented in PYTHON (Rossum, 1995), LensTools takes full advantage of a range of state-of-the art techniques developed by the large and growing open-source software community (Jones et al., 2001; McKinney, 2010; Astrophy Collaboration, 2013; Pedregosa et al., 2011; Foreman-Mackey et al., 2013). We made the LensTools code available on the Python Package Index and published its documentation on http://lenstools.readthedocs.io.
Appelhans, Marc S; Wood, Kenneth R; Wagner, Warren L
2017-01-01
Platydesma , an endemic genus to the Hawaiian Islands containing four species, has long been considered of obscure origin. Recent molecular phylogenetic studies have unequivocally placed Platydesma within the widespread genus Melicope as sister to the rest of the Hawaiian species of Melicope . This makes submerging Platydesma into Melicope necessary. We make the necessary new combinations: Melicope cornuta (Hillebr.) Appelhans, K.R. Wood & W.L. Wagner, M. cornuta var. decurrens (B.C.Stone) Appelhans, K.R. Wood & W.L. Wagner, M. remyi (Sherff) Appelhans, K.R. Wood & W.L. Wagner, and M. rostrata (Hillebr.) Appelhans, K.R. Wood & W.L. Wagner. An additional species that has been recognized within Platydesma should now be recognized under its original name M. spathulata A. Gray. All Hawaiian species belong to Melicope section Pelea. Our molecular phylogenetic studies also showed that in addition to merging Platydesma into section Pelea, five species described from New Caledonia need to be excluded from the section in order to achieve monophyly of section Pelea.
Atmospheric pressure-MOVPE growth of GaSb/GaAs quantum dots
NASA Astrophysics Data System (ADS)
Tile, Ngcali; Ahia, Chinedu C.; Olivier, Jaco; Botha, Johannes Reinhardt
2018-04-01
This study focuses on the growth of GaSb/GaAs quantum dots (QD) using an atmospheric pressure MOVPE system. For the best uncapped dots, the average dot height, base diameter and density are 5 nm, 45 nm and 4.5×1010 cm-2, respectively. Capping of GaSb QDs at high temperatures caused flattening and formation of thin inhomogeneous GaSb layer inside GaAs resulting in no obvious QD PL peak. Capping at low temperatures lead to the formation of dot-like features and a wetting layer (WL) with distinct PL peaks for QD and WL at 1097 nm and 983 nm respectively. Some of the dot-like features had voids. An increase in excitation power caused the QD and WL peaks to shift to higher energies. This is attributed to electrostatic band bending leading to triangular potential wells, typical of type-II alignment between GaAs and strained GaSb. Variable temperature PL measurements of the QD sample showed the decrease in the intensity of the WL peak to be faster than that of the QD peak as the temperature increased.
NASA Technical Reports Server (NTRS)
Simon, J. I.; Matzel, J. E. P.; Simon, S. B.; Weber, P. K.; Grossman, L.; Ross, D. K.; Hutcheon, I. D.
2014-01-01
Wark-Lovering (WL) rims [1] surrounding many refractory inclusions represent marker events in the early evolution of the Solar System in which many inclusions were exposed to changes in pressure [2], temperature [3], and isotopic reservoirs [4-7]. The effects of these events can be complex, not only producing mineralogical variability of WL rims [2], but also leading to mineralogical [8-10] and isotopic [7, 11, 12] changes within inclusion interiors. Extreme oxygen isotopic heterogeneity measured in CAIs has been explained by mixing between distinct oxygen gas reservoirs in the nebula [13]. Some WL rims contain relatively simple mineral layering and/or are isotopically homogeneous [14, 15]. As part of a larger effort to document and understand the modifications observed in some CAIs, an inclusion (L6) with a complex WL rim from Leoville, a member of the reduced CV3 subgroup was studied. Initial study of the textures and mineral chemistry was presented by [16]. Here we present NanoSIMS oxygen isotopic measurements to complement these petrologic observations.
Degradation of rizazole in water-sediment systems.
Zhang, Changpeng; Zhao, Hua; Ping, Lifeng; Cai, Xiaoming; Wu, Min; He, Hongmei; Zhang, Chunrong; Zhu, Yahong; Li, Zhen
2013-01-01
This study investigated the degradation of rizazole in water-sediment systems (West Lake system, WL; Beijing-Hangzhou Grand Canal system, BG) with two different types of sediments under aerobic and anaerobic conditions. The half-lives of rizazole in the WL water phase (14.59-15.13 d) were similar to those in the BG water phase (15.90-16.46 d). Within 3-7 d, the rizazole concentration in the sediments reached the maximum values, i.e., equilibrium. Rizazole dissipation was faster in the WL sediment phase with higher organic matter content (T(1/2) = 18.99-19.09 d) compared with the BG sediment phase (T(1/2) = 31.08-33.32 d). Rizazole degradation was slightly faster in the West Lake water-sediment system (WL system) (T(1/2) = 17.11-18.05 d) than in the Beijing-Hangzhou Grand Canal water-sediment system (BG system) (T(1/2) = 20.51-25.02 d). The aerobic degradation of rizazole was similar to its anaerobic degradation in the water-sediment system. The findings are useful to understand the behavior of pesticide in environment.
Liu, L B; Wu, C M; Wen, J; Chen, J L; Zheng, M Q; Zhao, G P
2009-03-01
Antibody titers raised for vaccinations against avian influenza (AI) and Newcastle disease (ND) were higher in Chinese Beijing-You (BJY) than in White Leghorn (WL) ( P < 0.001), but there was no breed difference in titers for sheep red blood cells (SRBC). Genotyping by PCR-SSCP identified seven haplotypes in WL and 17 in BJY. After sequencing PCR products (35 and 85, respectively), 43 (WL) and 47 (BJY) single nucleotide polymorphisms (SNPs) were found in the 264 bp of exon 2. In WL chickens, significant associations were found with antibody responses to AI (two SNPs), ND (six SNPs), and SRBC (one SNP), while in BJY there was association with responses to ND (two SNPs) and SRBC (two SNPs), but none with AI. These results indicate that the genomic region bearing exon 2 of the major histocompatibility complex B-F gene has significant effects on antibody responses to SRBC and vaccination against AI and ND. Different SNPs affected antibody titers for each of the antigens and they differed between these very distinct breeds.
NASA Astrophysics Data System (ADS)
Ananthanarayanan, A.; Ambashta, R. D.; Sudarsan, V.; Ajithkumar, T.; Sen, D.; Mazumder, S.; Wattal, P. K.
2017-04-01
Sodium zirconium phosphate (NZP) ceramics have been prepared using conventional sintering and hot isostatic pressing (HIP) routes. The structure of NZP ceramics, prepared using the HIP route, has been compared with conventionally sintered NZP using a combination of X-ray diffraction (XRD) and (31P and 23Na) nuclear magnetic resonance (NMR) spectroscopy techniques. It is observed that NZP with no waste loading is aggressive toward the steel HIP-can during hot isostatic compaction and significant fraction of cations from the steel enter the ceramic material. Waste loaded NZP samples (10 wt% simulated FBR waste) show significantly low can-interaction and primary NZP phase is evident in this material. Upon exposure of can-interacted and waste loaded NZP to boiling water and steam, 31P NMR does not detect any major modifications in the network structure. However, the 23Na NMR spectra indicate migration of Na+ ions from the surface and possible re-crystallization. This is corroborated by Small-Angle Neutron Scattering (SANS) data and Scanning Electron Microscopy (SEM) measurements carried out on these samples.
The nutrient load from food waste generated onboard ships in the Baltic Sea.
Wilewska-Bien, Magda; Granhag, Lena; Andersson, Karin
2016-04-15
The combination of the sensitive characteristics of the Baltic Sea and the intense maritime traffic makes the marine environment vulnerable to anthropogenic influences. The theoretical scenario calculated in this study shows that the annually generated food waste onboard ships in traffic in the Baltic Sea contains about 182tonnes of nitrogen and 34tonnes of phosphorus. Today, all food waste generated onboard can be legally discharged into the marine environment at a distance of 12NM from the nearest land. The annual load of nitrogen contained in the food waste corresponds to 52% of load of nitrogen from the ship-generated sewage. Future regulations for sewage discharge in the Baltic Sea will require significant reduction of total nitrogen and phosphorus released. The contribution of nutrients from food waste compared to sewage will therefore be relatively larger in the future, if food waste still can be legally discharged. Copyright © 2015 Elsevier Ltd. All rights reserved.
Liu, Jiawei; Xu, Guanbao; Dong, Weiliang; Xu, Ning; Xin, Fengxue; Ma, Jiangfeng; Fang, Yan; Zhou, Jie; Jiang, Min
2018-06-01
Polyethylene terephthalate (PET), a synthetic polyester material made of diethyl terephthalate (DET) monomers, is widely used in plastic products of daily life and caused serious pollution to the global environment. Microbial metabolism is the major degradation pathway responsible for DET degradation in natural soil; however, the microbial DET-degradation mechanism remains unclear. In this study, the newly isolated strain WL-3, identified as belonging to the genus Delftia, was found to be able to degrade 94% of 5 g·L -1 of DET and utilize it as the sole carbon source for growth within 7 days. Furthermore, strain WL-3 was capable of stable DET degradation under a wide range of pH values (6.0-9.0) and temperatures (20-42°C) with the optimal pH and temperature of 7.0 and 30°C respectively. Furthermore, the biochemical pathway of DET degradation by strain WL-3 was proposed based on the identified degradation intermediates. DET is first transformed into terephthalic acid (TPA) by the hydrolysis of two ester bonds, which is subsequently converted to protocatechuic acid (PCA) and further mineralized. SEM observations revealed obvious cracks on the surface of PET film after inoculation of 2 months with strain WL-3, indicating the strain's potential for the bioremediation of PET-contaminated environments. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.
Comparison of apical transportation between ProFile and ProTaper NiTi rotary instruments.
Iqbal, M K; Firic, S; Tulcan, J; Karabucak, B; Kim, S
2004-06-01
To use a newly developed radiographic technique to compare apical transportation and loss of working length (WL) between.06 taper ProFile Series 29 and ProTaper nickel-titanium (NiTi) rotary instruments in vitro. Mesio-buccal canals of 40 extracted mandibular molars were randomly divided into two groups. Group 1 was instrumented with ProFile and group 2 with ProTaper instruments according to the manufacturers' directions. A specially constructed radiographic jig with a Schick digital radiographic system (Schick Technologies Inc., Long Island City, NY, USA) was used to take pre- and postoperative radiographs of the samples at predetermined angulations. Using AutoCAD 2000 (Autodesk Inc., San Rafael, CA, USA), the central axes of initial and final instruments were radiographically superimposed to determine the loss of WL and degree of transportation at D(0), D(1), D(2) and D(4) from the WL. Data were analysed using repeated-measures anova. A statistically significant difference in apical transportation was found at the D(4) level between the two groups (P = 0.05). There was no statistical significance regarding postinstrumentation change in WL between groups. Spearman's Bivariate Correlation analysis indicated no statistically significant relationship between the radius of curvature and transportation. The results indicate that both ProTaper and ProFile instruments are comparable to each other in regards to their ability to optimally enlarge root canal with minimal transportation and loss of WL in vitro.
Effect of yoga on self-rated visual discomfort in computer users.
Telles, Shirley; Naveen, K V; Dash, Manoj; Deginal, Rajendra; Manjunath, N K
2006-12-03
'Dry eye' appears to be the main contributor to the symptoms of computer vision syndrome. Regular breaks and the use of artificial tears or certain eye drops are some of the options to reduce visual discomfort. A combination of yoga practices have been shown to reduce visual strain in persons with progressive myopia. The present randomized controlled trial was planned to evaluate the effect of a combination of yoga practices on self-rated symptoms of visual discomfort in professional computer users in Bangalore. Two hundred and ninety one professional computer users were randomly assigned to two groups, yoga (YG, n = 146) and wait list control (WL, n = 145). Both groups were assessed at baseline and after sixty days for self-rated visual discomfort using a standard questionnaire. During these 60 days the YG group practiced an hour of yoga daily for five days in a week and the WL group did their usual recreational activities also for an hour daily for the same duration. At 60 days there were 62 in the YG group and 55 in the WL group. While the scores for visual discomfort of both groups were comparable at baseline, after 60 days there was a significantly decreased score in the YG group, whereas the WL group showed significantly increased scores. The results suggest that the yoga practice appeared to reduce visual discomfort, while the group who had no yoga intervention (WL) showed an increase in discomfort at the end of sixty days.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sallaberry, Cedric Jean-Marie; Helton, Jon C.
2015-05-01
Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high - consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to d eactivate the entire system before the SL system fails (i.e., degrades into a configurationmore » that could allow an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). This report describes the Fortran 90 program CPLOAS_2 that implements the following representations for PLOAS for situations in which both link physical properties and link failure properties are time - dependent: (i) failure of all SLs before failure of any WL, (ii) failure of any SL before f ailure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS can be included in the calculations performed by CPLOAS_2. Keywords: Aleatory uncertainty, CPLOAS_2, Epistemic uncertainty, Probability of loss of assured safety, Strong link, Uncertainty analysis, Weak link« less
SU-E-J-48: Imaging Origin-Radiation Isocenter Coincidence for Linac-Based SRS with Novalis Tx
DOE Office of Scientific and Technical Information (OSTI.GOV)
Geraghty, C; Workie, D; Hasson, B
Purpose To implement and evaluate an image-based Winston-Lutz (WL) test to measure the displacement between ExacTrac imaging origin and radiation isocenter on a Novalis Tx system using RIT V6.2 software analysis tools. Displacement between imaging and radiation isocenters was tracked over time. The method was applied for cone-based and MLC-based WL tests. Methods The Brainlab Winston-Lutz phantom was aligned to room lasers. The ExacTrac imaging system was then used to detect the Winston- Lutz phantom and obtain the displacement between the center of the phantom and the imaging origin. EPID images of the phantom were obtained at various gantry andmore » couch angles and analyzed with RIT calculating the phantom center to radiation isocenter displacement. The RIT and Exactrac displacements were combined to calculate the displacement between imaging origin and radiation isocenter. Results were tracked over time. Results Mean displacements between ExacTrac origin and radiation isocenter were: VRT: −0.1mm ± 0.3mm, LNG: 0.5mm ± 0.2mm, LAT: 0.2mm ± 0.2mm (vector magnitude of 0.7 ± 0.2mm). Radiation isocenter was characterized by the mean of the standard deviations of the WL phantom displacements: σVRT: 0.2mm, σLNG: 0.4mm, σLAT: 0.6mm. The linac couch base was serviced to reduce couch walkout. This reduced σLAT to 0.2mm. These measurements established a new baseline of radiation isocenter-imaging origin coincidence. Conclusion The image-based WL test has ensured submillimeter localization accuracy using the ExacTrac imaging system. Standard deviations of ExacTrac-radiation isocenter displacements indicate that average agreement within 0.3mm is possible in each axis. This WL test is a departure from the tradiational WL in that imaging origin/radiation isocenter agreement is the end goal not lasers/radiation isocenter.« less
Long-term effect of weight loss on body composition and performance in elite athletes.
Garthe, Ina; Raastad, Truls; Sundgot-Borgen, Jorunn
2011-10-01
When weight loss (WL) is needed, it is recommended that athletes do it gradually by 0.5-1 kg/wk through moderate energy restriction. However, the effect of WL rate on long-term changes in body composition (BC) and performance has not been investigated in elite athletes. To compare changes in body mass (BM), fat mass (FM), lean body mass (LBM), and performance 6 and 12 mo after 2 different WL interventions promoting loss of 0.7% vs. 1.4% of body weight per wk in elite athletes. Twenty-three athletes completed 6- and 12-mo postintervention testing (slow rate [SR] n = 14, 23.5 ± 3.3 yr, 72.2 ± 12.2 kg; fast rate [FR] n = 9, 21.4 ± 4.0 yr, 71.6 ± 12.0 kg). The athletes had individualized diet plans promoting the predetermined weekly WL during intervention, and 4 strength-training sessions per wk were included. BM, BC, and strength (1-repetition maximum) were tested at baseline, postintervention, and 6 and 12 mo after the intervention. BM decreased by ~6% in both groups during the intervention but was not different from baseline values after 12 mo. FM decreased in SR and FR during the intervention by 31% ± 3% vs. 23% ± 4%, respectively, but was not different from baseline after 12 mo. LBM and upper body strength increased more in SR than in FR (2.0% ± 1.3% vs. 0.8% ± 1.1% and 12% ± 2% vs. 6% ± 2%) during the intervention, but after 12 mo there were no significant differences between groups in BC or performance. There were no significant differences between groups after 12 mo, suggesting that WL rate is not the most important factor in maintaining BC and performance after WL in elite athletes.
Teo, Shaun Y M; Newton, Michael J; Newton, Robert U; Dempsey, Alasdair R; Fairchild, Timothy J
2016-10-01
Teo, SYM, Newton, MJ, Newton, RU, Dempsey, AR, and Fairchild, TJ. Comparing the effectiveness of a short-term vertical jump vs. weightlifting program on athletic power development. J Strength Cond Res 30(10): 2741-2748, 2016-Efficient training of neuromuscular power and the translation of this power to sport-specific tasks is a key objective in the preparation of athletes involved in team-based sports. The purpose of this study was to compare changes in center of mass (COM) neuromuscular power and performance of sport-specific tasks after short-term (6-week) training adopting either Olympic-style weightlifting (WL) exercises or vertical jump (VJ) exercises. Twenty-six recreationally active men (18-30 years; height: 178.7 ± 8.3 cm; mass: 78.6 ± 12.2 kg) were randomly allocated to either a WL or VJ training group and performance during the countermovement jump (CMJ), squat jump (SJ), depth jump (DJ), 20-m sprint, and the 5-0-5 agility test-assessed pre and posttraining. Despite the WL group demonstrating larger increases in peak power output during the CMJ (WL group: 10% increase, d = 0.701; VJ group: 5.78% increase, d = 0.328) and SJ (WL group: 12.73% increase, d = 0.854; VJ group: 7.27% increase, d = 0.382), no significant between-group differences were observed in any outcome measure studied. There was a significant main effect of time observed for the 3 VJs (CMJ, SJ, and DJ), 0- to 5-m and 0- to 20-m sprint times, and the 5-0-5 agility test time, which were all shown to improve after the training (all main effects of time p < 0.01). Irrespective of the training approach adopted by coaches or athletes, addition of either WL or VJ training for development of power can improve performance in tasks associated with team-based sports, even in athletes with limited preseason training periods.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kalapurakal, John A., E-mail: j-kalapurakal@northwestern.edu; Pokhrel, Damodar; Gopalakrishnan, Mahesh
Purpose: To demonstrate the dosimetric advantages of intensity modulated radiation therapy (IMRT) in children with Wilms tumor (WT) undergoing whole-liver (WL) RT. Methods and Materials: Computed tomography simulation scans of 10 children, either 3 (3D) or 4-dimensional (4D), were used for this study. The WL PTV was determined by the 3D or 4D liver volumes, with a margin of 1 cm. A total of 40 WL RT plans were performed: 10 each for left- and right-sided WT with IMRT and anteroposterior-posteroanterior (AP-PA) techniques. The radiation dose-volume coverage of the WL planning target volume (PTV), remaining kidney, and other organs weremore » analyzed and compared. Results: The 95% dose coverage to WL PTV for left and right WT were as follows: 97% ± 4% (IMRT), 83% ± 8% (AP-PA) (P<.01) and 99% ± 1% (IMRT), 94% ± 5% (AP-PA) (P<.01), respectively. When 3D WL PTV was used for RT planning, the AP-PA technique delivered 95% of dose to only 78% ± 13% and 88% ± 8% of 4D liver volume. For left WT, the right kidney V15 and V10 for IMRT were 29% ± 7% and 55% ± 8%, compared with 61% ± 29% (P<.01) and 78% ± 25% (P<.01) with AP-PA. For right WT, the left kidney V15 and V10 were 0 ± 0 and 2% ± 3% for IMRT, compared with 25% ± 19% (P<.01) and 40% ± 31% (P<.01) for AP-PA. Conclusions: The use of IMRT and 4D treatment planning resulted in the delivery of a higher RT dose to the liver compared with the standard AP-PA technique. Whole-liver IMRT also delivered a significantly lower dose to the remaining kidney.« less
Allen, K D; Arbeeva, L; Callahan, L F; Golightly, Y M; Goode, A P; Heiderscheit, B C; Huffman, K M; Severson, H H; Schwartz, T A
2018-03-01
To compare the effectiveness of physical therapy (PT, evidence-based approach) and internet-based exercise training (IBET), each vs a wait list (WL) control, among individuals with knee osteoarthritis (OA). Randomized controlled trial of 350 participants with symptomatic knee OA, allocated to standard PT, IBET and WL control in a 2:2:1 ratio, respectively. The PT group received up to eight individual visits within 4 months. The IBET program provided tailored exercises, video demonstrations, and guidance on progression. The primary outcome was the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC, range 0 [no problems]-96 [extreme problems]), assessed at baseline, 4 months (primary time point) and 12 months. General linear mixed effects modeling compared changes in WOMAC among study groups, with superiority hypotheses testing differences between each intervention group and WL and non-inferiority hypotheses comparing IBET with PT. At 4-months, improvements in WOMAC score did not differ significantly for either the IBET or PT group compared with WL (IBET: -2.70, 95% Confidence Interval (CI) = -6.24, 0.85, P = 0.14; PT: -3.36, 95% (CI) = -6.84, 0.12, P = 0.06). Similarly, at 12-months mean differences compared to WL were not statistically significant for either group (IBET: -2.63, 95% CI = -6.37, 1.11, P = 0.17; PT: -1.59, 95% CI = -5.26, 2.08, P = 0.39). IBET was non-inferior to PT at both time points. Improvements in WOMAC score following IBET and PT did not differ significantly from the WL group. Additional research is needed to examine strategies for maximizing benefits of exercise-based interventions for patients with knee OA. NCT02312713. Published by Elsevier Ltd.
Stange, I; Poeschl, K; Stehle, P; Sieber, C C; Volkert, D
2013-04-01
To identify nursing home residents with malnutrition or at risk of malnutrition by using different markers, determine if the Mini Nutritional Assessment (MNA®) is able to identify all residents at risk according to single risk markers and explore the relation between risk markers and functional impairment. Cross-sectional study. Six German nursing homes. 286 residents (86±7y, 89% female). Screening for malnutrition or its risk included low BMI (≤22 kg/m²), recent weight loss (WL), low food intake (LI) as single risk markers and MNA (<24 points, p.) as composite marker. Prevalence of single nutritional risk markers in different MNA categories was compared by cross-tables. Mental (cognition, mood) and physical function (mobility) were assessed by interviewing nursing staff and association of impaired status to nutritional risk markers determined by Chi² test. 32.9% of residents had a low BMI, 11.9% WL and 21.3% LI. 60.2% were categorized malnourished (18.2%) or at risk of malnutrition (42.0%) by MNA. 64% presented at least one of these nutritional risk markers. Of those classified malnourished by MNA, 96.2% also showed low BMI, WL or LI. In contrast, eleven residents (9.6%) considered well-nourished by MNA presented single risk markers (9 low BMI, 2 WL). Cognitive impairment, depressive symptoms and immobility was present in 59.0%, 20.8% and 25.5%, respectively. Functional impairment, and in particular severe impairment, was to a higher proportion present in residents at nutritional risk independent of the chosen marker (MNA<24 p., low BMI, WL, LI). The high prevalence of nutritional risk highlights the importance of regular screening of nursing home residents. The MNA identified nearly all residents with low BMI, WL and LI. The close association between nutritional risk and functional impairment requires increased awareness for nutritional problems especially in functionally impaired residents, to early initiate nutritional measures and thus, prevent further nutritional and functional deterioration.
del Genio, Federica; Alfonsi, Lucia; Marra, Maurizio; Finelli, Carmine; del Genio, Gianmattia; Rossetti, Gianluca; del Genio, Alberto; Contaldo, Franco; Pasanisi, Fabrizio
2007-12-01
Bariatric surgery is considered the most effective treatment for reducing excess body weight and maintaining weight loss (WL) in severely obese patients. There are limited data evaluating metabolic and body composition changes after different treatments in type III obese (body mass index [BMI] > 40 kg/m(2)). Twenty patients (9 males, 11 females; 37.6 +/- 8 years; BMI = 50.1 +/- 8 kg/m(2)) treated with dietary therapy and lifestyle correction (group 1) have been compared with 20 matched patients (41.8 +/- 6 years; BMI = 50.4 +/- 6 kg/m(2)) treated with laparoscopic gastric bypass (LGBP; group 2). Patients have been evaluated before treatment and after >10% WL obtained on average 6 weeks after LGBP and 30 weeks after integrated medical treatment. Metabolic syndrome (MS) was evaluated using the Adult Treatment Panel III/America Heart Association (ATP III/AHA) criteria. Resting metabolic rate (RMR) and respiratory quotient (RQ) was assessed with indirect calorimetry; body composition with bioimpedance analysis. At entry, RMR/fat-free mass (FFM) was 34.2 +/- 7 kcal/24 h.kg in group 1 and 35.1 +/- 8 kcal/24 h.kg in group 2 and did not decrease in both groups after 10% WL (31.8 +/- 6 vs 34.0 +/- 6). Percent FFM and fat mass (FM) was 50.7 +/- 7% and 49.3 +/- 7% in group 1 and 52.1 +/- 6% and 47.9 +/- 6% in group 2, respectively (p = n.s.). After WL, body composition significantly changed only in group 1 (% FFM increased to 55.9 +/- 6 and % FM decreased to 44.1 +/- 6; p = 0.002). After >10% WL, MS prevalence decreases precociously in surgically treated patients; some improvements in body composition are observed in nonsurgically treated patients only. Further investigations are needed to evaluate long-term effects of bariatric surgery on body composition and RMR after stable WL.
Developing a master plan for hospital solid waste management: A case study
DOE Office of Scientific and Technical Information (OSTI.GOV)
Karamouz, Mohammad; Zahraie, Banafsheh; Kerachian, Reza
2007-07-01
Disposal of about 1750 tons of solid wastes per day is the result of a rapid population growth in the province of Khuzestan in the south west of Iran. Most of these wastes, especially hospital solid wastes which have contributed to the pollution of the environment in the study area, are not properly managed considering environmental standards and regulations. In this paper, the framework of a master plan for managing hospital solid wastes is proposed considering different criteria which are usually used for evaluating the pollution of hospital solid waste loads. The effectiveness of the management schemes is also evaluated.more » In order to rank the hospitals and determine the share of each hospital in the total hospital solid waste pollution load, a multiple criteria decision making technique, namely analytical hierarchy process (AHP), is used. A set of projects are proposed for solid waste pollution control and reduction in the proposed framework. It is partially applied for hospital solid waste management in the province of Khuzestan, Iran. The results have shown that the hospitals located near the capital city of the province, Ahvaz, produce more than 43% of the total hospital solid waste pollution load of the province. The results have also shown the importance of improving management techniques rather than building new facilities. The proposed methodology is used to formulate a master plan for hospital solid waste management.« less
Influence of cervical preflaring on apical file size determination.
Pecora, J D; Capelli, A; Guerisoli, D M Z; Spanó, J C E; Estrela, C
2005-07-01
To investigate the influence of cervical preflaring with different instruments (Gates-Glidden drills, Quantec Flare series instruments and LA Axxess burs) on the first file that binds at working length (WL) in maxillary central incisors. Forty human maxillary central incisors with complete root formation were used. After standard access cavities, a size 06 K-file was inserted into each canal until the apical foramen was reached. The WL was set 1 mm short of the apical foramen. Group 1 received the initial apical instrument without previous preflaring of the cervical and middle thirds of the root canal. Group 2 had the cervical and middle portion of the root canals enlarged with Gates-Glidden drills sizes 90, 110 and 130. Group 3 had the cervical and middle thirds of the root canals enlarged with nickel-titanium Quantec Flare series instruments. Titanium-nitrite treated, stainless steel LA Axxess burs were used for preflaring the cervical and middle portions of root canals from group 4. Each canal was sized using manual K-files, starting with size 08 files with passive movements until the WL was reached. File sizes were increased until a binding sensation was felt at the WL, and the instrument size was recorded for each tooth. The apical region was then observed under a stereoscopic magnifier, images were recorded digitally and the differences between root canal and maximum file diameters were evaluated for each sample. Significant differences were found between experimental groups regarding anatomical diameter at the WL and the first file to bind in the canal (P < 0.01, 95% confidence interval). The major discrepancy was found when no preflaring was performed (0.151 mm average). The LA Axxess burs produced the smallest differences between anatomical diameter and first file to bind (0.016 mm average). Gates-Glidden drills and Flare instruments were ranked in an intermediary position, with no statistically significant differences between them (0.093 mm average). The instrument binding technique for determining anatomical diameter at WL is not precise. Preflaring of the cervical and middle thirds of the root canal improved anatomical diameter determination; the instrument used for preflaring played a major role in determining the anatomical diameter at the WL. Canals preflared with LA Axxess burs created a more accurate relationship between file size and anatomical diameter.
de Gregorio, C; Paranjpe, A; Garcia, A; Navarrete, N; Estevez, R; Esplugues, E O; Cohenca, N
2012-05-01
To assess the ability of sodium hypochlorite (NaOCl) to penetrate simulated lateral canals and to reach working length (WL) when using the self-adjusting file (SAF). Seventy single-rooted teeth with oval-shaped canals were used. Upon access, presence of a single canal was confirmed by direct visualization under a dental-operating microscope. Canal length and patency were obtained using a size 10 K-file and root length standardized to 18 mm. Pre-enlargement was restricted to the coronal one-third. The apical size of each canal was gauged at WL and samples larger than size 30 were excluded. Canals were instrumented for 5 min using the SAF system while delivering a total of 20 mL of 5.25% NaOCl and 5 mL of 17% EDTA. Then, the apical diameters were standardized to size 35 using hand files. Four hundred and twenty simulated lateral canals were then created during the clearing process and roots coated with wax to create a closed system. All samples were then cleared and randomly assigned to four experimental groups: 1 (n = 15) positive pressure; 2 (n = 15) SAF without pecking motion; 3 (n = 15) SAF with pecking motion; 4 (n = 15) apical negative pressure (ANP) irrigation and (n = 10) control groups. Samples were scored on the basis of the ability of the contrast solution to reach WL and permeate into the simulated lateral canals to at least 50% of the total length. The Kruskal-Wallis test was used to analyse irrigant penetration and the Tukey test to determine statistical differences between groups (P < 0.05). All samples irrigated with ANP were associated with irrigant penetration to WL (Table 1). The differences between group 4 (ANP) and all other groups were significant in penetration to WL (P < 0.05). The pecking motion allowed for further penetration of the irrigant when using the SAF system but failed to irrigate at WL. None of the experimental groups demonstrated predictable irrigation of simulated lateral canals. In this laboratory model, ANP was the only delivery system capable of irrigating consistently to full WL. None of the systems tested produced complete irrigation in artificial lateral canals. © 2012 International Endodontic Journal.
Capson-Tojo, Gabriel; Trably, Eric; Rouez, Maxime; Crest, Marion; Steyer, Jean-Philippe; Delgenès, Jean-Philippe; Escudié, Renaud
2017-06-01
The increasing food waste production calls for developing efficient technologies for its treatment. Anaerobic processes provide an effective waste valorization. The influence of the initial substrate load on the performance of batch dry anaerobic co-digestion reactors treating food waste and cardboard was investigated. The load was varied by modifying the substrate to inoculum ratio (S/X), the total solids content and the co-digestion proportions. The results showed that the S/X was a crucial parameter. Within the tested values (0.25, 1 and 4gVS·gVS -1 ), only the reactors working at 0.25 produced methane. Methanosarcina was the main archaea, indicating its importance for efficient methanogenesis. Acidogenic fermentation was predominant at higher S/X, producing hydrogen and other metabolites. Higher substrate conversions (≤48%) and hydrogen yields (≤62mL·gVS -1 ) were achieved at low loads. This study suggests that different value-added compounds can be produced in dry conditions, with the initial substrate load as easy-to-control operational parameter. Copyright © 2017 Elsevier Ltd. All rights reserved.
Mahesh, MC; Bhandary, Shreetha
2017-01-01
Introduction Stresses generated during root canal instrumentation have been reported to cause apical cracks. The smaller, less pronounced defects like cracks can later propagate into vertical root fracture, when the tooth is subjected to repeated stresses from endodontic or restorative procedures. Aim This study evaluated occurrence of apical cracks with stainless steel hand files, rotary NiTi RaCe and K3 files at two different instrumentation lengths. Materials and Methods In the present in vitro study, 60 mandibular premolars were mounted in resin blocks with simulated periodontal ligament. Apical 3 mm of the root surfaces were exposed and stained using India ink. Preoperative images of root apices were obtained at 100x using stereomicroscope. The teeth were divided into six groups of 10 each. First two groups were instrumented with stainless steel files, next two groups with rotary NiTi RaCe files and the last two groups with rotary NiTi K3 files. The instrumentation was carried out till the apical foramen (Working Length-WL) and 1 mm short of the apical foramen (WL-1) with each file system. After root canal instrumentation, postoperative images of root apices were obtained. Preoperative and postoperative images were compared and the occurrence of cracks was recorded. Descriptive statistical analysis and Chi-square tests were used to analyze the results. Results Apical root cracks were seen in 30%, 35% and 20% of teeth instrumented with K-files, RaCe files and K3 files respectively. There was no statistical significance among three instrumentation systems in the formation of apical cracks (p=0.563). Apical cracks were seen in 40% and 20% of teeth instrumented with K-files; 60% and 10% of teeth with RaCe files and 40% and 0% of teeth with K3 files at WL and WL-1 respectively. For groups instrumented with hand files there was no statistical significance in number of cracks at WL and WL-1 (p=0.628). But for teeth instrumented with RaCe files and K3 files significantly more number of cracks were seen at WL than WL-1 (p=0.057 for RaCe files and p=0.087 for K3 files). Conclusion There was no statistical significance between stainless steel hand files and rotary files in terms of crack formation. Instrumentation length had a significant effect on the formation of cracks when rotary files were used. Using rotary instruments 1 mm short of apical foramen caused lesser crack formation. But, there was no statistically significant difference in number of cracks formed with hand files at two instrumentation levels. PMID:28274036
Devale, Madhuri R; Mahesh, M C; Bhandary, Shreetha
2017-01-01
Stresses generated during root canal instrumentation have been reported to cause apical cracks. The smaller, less pronounced defects like cracks can later propagate into vertical root fracture, when the tooth is subjected to repeated stresses from endodontic or restorative procedures. This study evaluated occurrence of apical cracks with stainless steel hand files, rotary NiTi RaCe and K3 files at two different instrumentation lengths. In the present in vitro study, 60 mandibular premolars were mounted in resin blocks with simulated periodontal ligament. Apical 3 mm of the root surfaces were exposed and stained using India ink. Preoperative images of root apices were obtained at 100x using stereomicroscope. The teeth were divided into six groups of 10 each. First two groups were instrumented with stainless steel files, next two groups with rotary NiTi RaCe files and the last two groups with rotary NiTi K3 files. The instrumentation was carried out till the apical foramen (Working Length-WL) and 1 mm short of the apical foramen (WL-1) with each file system. After root canal instrumentation, postoperative images of root apices were obtained. Preoperative and postoperative images were compared and the occurrence of cracks was recorded. Descriptive statistical analysis and Chi-square tests were used to analyze the results. Apical root cracks were seen in 30%, 35% and 20% of teeth instrumented with K-files, RaCe files and K3 files respectively. There was no statistical significance among three instrumentation systems in the formation of apical cracks (p=0.563). Apical cracks were seen in 40% and 20% of teeth instrumented with K-files; 60% and 10% of teeth with RaCe files and 40% and 0% of teeth with K3 files at WL and WL-1 respectively. For groups instrumented with hand files there was no statistical significance in number of cracks at WL and WL-1 (p=0.628). But for teeth instrumented with RaCe files and K3 files significantly more number of cracks were seen at WL than WL-1 (p=0.057 for RaCe files and p=0.087 for K3 files). There was no statistical significance between stainless steel hand files and rotary files in terms of crack formation. Instrumentation length had a significant effect on the formation of cracks when rotary files were used. Using rotary instruments 1 mm short of apical foramen caused lesser crack formation. But, there was no statistically significant difference in number of cracks formed with hand files at two instrumentation levels.
Ugwuanyi, J Obeta; Harvey, L M; McNeil, B
2005-04-01
Thermophilic aerobic digestion (TAD) is a relatively new, dynamic and versatile low technology for the economic processing of high strength waste slurries. Waste so treated may be safely disposed of or reused. In this work a model high strength agricultural waste, potato peel, was subjected to TAD to study the effects of oxygen supply at 0.1, 0.25, 0.5 and 1.0 vvm (volume air per volume slurry per minute) under batch conditions at 55 degrees C for 156 h on the process. Process pH was controlled at 7.0 or left unregulated. Effects of waste load, as soluble chemical oxygen demand (COD), on TAD were studied at 4.0, 8.0, 12.0 and 16.0 gl(-1) (soluble COD) at pH 7.0, 0.5 vvm and 55 degrees C. Efficiency of treatment, as degradation of total solids, total suspended solids and soluble solid, as well as soluble COD significantly increased with aeration rate, while acetate production increased as the aeration rate decreased or waste load increased, signifying deterioration in treatment. Negligible acetate, and no other acids were produced at 1.0 vvm. Production of propionate and other acids increased after acetate concentration had started to decrease and, during unregulated reactions coincided with the drop in the pH of the slurry. Acetate production was more closely associated with periods of oxygen limitation than were other acids. Reduction in oxygen availability led to deterioration in treatment efficiency as did increase in waste load. These variables may be manipulated to control treated waste quality.
2011-11-01
Carbon Fiber Production– 02FCC-144”; C.F. Leit- ten, Jr., W.L. Griffith, A.L. Compere , and J.T. Shaffer, Society of Automotive Engineers, Inc., 2001. 8...Cost Carbon Fiber from Renewable Resources”; A.L. Compere , W.L. Griffith, C.F. Leitten, Jr., and J.T. Shaffer, Oak Ridge National Laboratory Report
How to Measure the Efficacy of VET Workplace Learning: The FET-WL Model
ERIC Educational Resources Information Center
Pineda-Herrero, Pilar; Quesada-Pallarès, Carla; Espona-Barcons, Berta; Mas-Torelló, Óscar
2015-01-01
Purpose: Workplace learning (WL) is a key part of vocational education and training (VET) because it allows students to develop their skills in a work environment, and provides important information about how well VET studies prepare skilled workers. Therefore, the purpose of this paper is to develop and validate an instrument to evaluate WL…
ERIC Educational Resources Information Center
Morris, Michael Lane; Heames, Joyce Thompson; McMillan, Heather S.
2011-01-01
Given the stresses associated with today's demanding workplaces, work/life (w/l) initiatives continue to grow in importance as an organizational development (OD) intervention. In a period of increasing accountability, it is important for scholars and practitioners to demonstrate how OD interventions, like w/l initiatives, can be used as a…
Lotito, Adriana Maria; De Sanctis, Marco; Pastore, Carlo; Di Iaconi, Claudio
2018-06-01
This study proposes the evaluation of the suitability of mesophilic anaerobic digestion as a simple technology for the treatment of the citrus waste produced by small-medium agro-industrial enterprises involved in the transformation of Citrus fruits. Two different stocks of citrus peel waste were used (i.e., fresh and stored citrus peel waste), to evaluate the influence of waste composition (variability in the type of processed Citrus fruits) and of storage (potentially necessary to operate the anaerobic digester continuously over the whole year due to the seasonality of the production) on anaerobic degradation treatability. A thorough characterization of the two waste types has been performed, showing that the fresh one has a higher solid and organic content, and that, in spite of the similar values of oil fraction amounts, the two stocks are significantly different in the composition of essential oils (43% of limonene and 34% of linalyl acetate in the fresh citrus waste and 20% of limonene and 74% of linalyl acetate in the stored citrus waste). Contrarily to what observed in previous studies, anaerobic digestion was successful and no reactor acidification occurred. No inhibition by limonene and linalyl acetate even at the maximum applied organic load value (i.e., 2.72 gCOD waste /gVS inoculum ) was observed in the treatment of the stored waste, with limonene and linalyl acetate concentrations of 104 mg/l and 385 mg/l, respectively. On the contrary, some inhibition was detected with fresh citrus peel waste when the organic load increased from 2.21 to 2.88 gCOD waste /gVS inoculum , ascribable to limonene at initial concentration higher than 150 mg/l. A good conversion into methane was observed with fresh peel waste, up to 0.33 [Formula: see text] at the highest organic load, very close to the maximum theoretical value of 0.35 [Formula: see text] , while a lower efficiency was achieved with stored peel waste, with a reduction down to 0.24 [Formula: see text] at the highest organic load. Copyright © 2018 Elsevier Ltd. All rights reserved.
Mine Waste Technology Program. Passive Treatment for Reducing Metal Loading
This report summarizes the results of Mine Waste Technology Program (MWTP) Activity III, Project 48, Passive Treatment Technology Evaluation for Reducing Metal Loading, funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by EPA and the U.S. Departmen...
10 CFR 72.120 - General considerations.
Code of Federal Regulations, 2014 CFR
2014-01-01
... waste, and/or high level waste including possible reaction with water during wet loading and unloading... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE General Design... reactor-related GTCC waste in an ISFSI or to store spent fuel, high-level radioactive waste, or reactor...
10 CFR 72.120 - General considerations.
Code of Federal Regulations, 2013 CFR
2013-01-01
... waste, and/or high level waste including possible reaction with water during wet loading and unloading... NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE General Design... reactor-related GTCC waste in an ISFSI or to store spent fuel, high-level radioactive waste, or reactor...
Dynamic mechanical analysis of waste tyre rubber filled brake friction composite materials
NASA Astrophysics Data System (ADS)
Rathi, Mukesh Kumar; Singh, Tej; Chauhan, Ranchan
2018-05-01
In this research work, the dynamic mechanical properties of waste tyre rubber filled friction composites were studied. Four friction composites with varying amount of waste rubber (0, 4, 8, 12 wt.%) and barium sulphate (38, 42, 46, 50 wt.%) were designed and fabricated as per industrial norms. Dynamic mechanical analysis has been carried out to characterize the storage modulus, loss modulus and damping factor of the fabricated friction composite. Experimental results indicated that storage modulus decreases with increasing waste rubber content up to particular loading (4 wt.%), and after that it increases with further loading. The loss modulus of the composites increases steadily with increasing waste rubber content whereas, damping factor remain maximum for 12 wt.% waste rubber filled friction composites.
López-Valcárcel, Beatriz G; González-Martel, Christian; Peiro, Salvador
2018-01-01
Objective Newcomb-Benford’s Law (NBL) proposes a regular distribution for first digits, second digits and digit combinations applicable to many different naturally occurring sources of data. Testing deviations from NBL is used in many datasets as a screening tool for identifying data trustworthiness problems. This study aims to compare public available waiting lists (WL) data from Finland and Spain for testing NBL as an instrument to flag up potential manipulation in WLs. Design Analysis of the frequency of Finnish and Spanish WLs first digits to determine if their distribution is similar to the pattern documented by NBL. Deviations from the expected first digit frequency were analysed using Pearson’s χ2, mean absolute deviation and Kuiper tests. Setting/participants Publicly available WL data from Finland and Spain, two countries with universal health insurance and National Health Systems but characterised by different levels of transparency and good governance standards. Main outcome measures Adjustment of the observed distribution of the numbers reported in Finnish and Spanish WL data to the expected distribution according to NBL. Results WL data reported by the Finnish health system fits first digit NBL according to all statistical tests used (p=0.6519 in χ2 test). For Spanish data, this hypothesis was rejected in all tests (p<0.0001 in χ2 test). Conclusions Testing deviations from NBL distribution can be a useful tool to identify problems with WL data trustworthiness and signalling the need for further testing. PMID:29743333
Miller, Gary D.; Jenks, Monica Z.; Vendela, Mandolyn; Norris, James L.; Muday, Gloria K.
2012-01-01
Objective. To investigate effects of weight loss on adipokines and health measures in obese older adults with symptomatic knee osteoarthritis. Methods. Participants were randomly assigned to either weight loss (WL) (men: 12, women: 14) or weight stable (WS) group (men: 12, women: 13). WL intervention included meal replacements and structured exercise training. Measurements of leptin, adiponectin, soluble leptin receptor, lifestyle behaviors, and body composition were collected at baseline and 6 months. Univariate analysis of covariance was performed on 6 month variables, and Spearman and partial correlations were made between variables. Results. Weight loss was 13.0% and 6.7% in WL for men and women, respectively. Women in WL had lower whole body and trunk fat than WS. The leptin : adiponectin ratio was lower for women in WL than WS at 6 months, with no group differences in adipokines for men. Leptin and free leptin index correlated with body fat in both genders at baseline. Interestingly, only women showed reductions in leptin (P < 0.100) and correlations between the percentage change leptin and trunk fat and the percentage changes in free leptin index with total fat and trunk fat. Partial correlations between 6 month adipokines after adjustments for covariates and group/time period show potential multivariate influences. Conclusions. In the presence of an effective weight loss intervention in older obese adults, there are significant relationships between weight and fat loss and leptin in women, but not men, suggesting gender-specific features of adipokine metabolism in this age group. PMID:23326650
Zhang, Cheng; Zong, Hong; Zhuge, Bin; Lu, Xinyao; Fang, Huiying; Zhuge, Jian
2015-07-01
Efficient bioconversion of D-xylose into various biochemicals is critical for the developing lignocelluloses application. In this study, we compared D-xylose utilization in Candida glycerinogenes WL2002-5 transformants expressing xylose reductase (XYL1) in D-xylose metabolism. C. glycerinogenes WL2002-5 expressing XYL1 from Schefferomyces stipitis can produce xylitol. Xylitol production by the recombinant strains was evaluated using a xylitol fermentation medium with glucose as a co-substrate. As glucose was found to be an insufficient co-substrate, various carbon sources were screened for efficient cofactor regeneration, and glycerol was found to be the best co-substrate. The effects of glycerol on the xylitol production rate by a xylose reductase gene (XYL1)-overexpressed mutant of C. glycerinogenes WL2002-5 were investigated. The XYL1-overexpressed mutant produced xylitol from D-xylose using glycerol as a co-substrate for cell growth and NAD (P) H regeneration: 100 g/L D-xylose was completely converted into xylitol when at least 20 g/L glycerol was used as a co-substrate. XYL1 overexpressed mutant grown on glycerol as co-substrate accumulated 2.1-fold increased xylitol concentration over those cells grown on glucose as co-substrate. XYL1 overexpressed mutant produced xylitol with a volumetric productivity of 0.83 g/L/h, and a xylitol yield of 98 % xylose. Recombinant yeast strains obtained in this study are promising candidates for xylitol production. This is the first report of XYL1 gene overexpression of C. glycerinogenes WL2002-5 for enhancing the efficiency of xylitol production.
NASA Astrophysics Data System (ADS)
Lee, Kyoung-Sun; Imada, Shinsuke; Watanabe, Kyoko; Bamba, Yumi; Brooks, David H.
2017-02-01
An X1.6 flare occurred in active region AR 12192 on 2014 October 22 at 14:02 UT and was observed by Hinode, IRIS, SDO, and RHESSI. We analyze a bright kernel that produces a white light (WL) flare with continuum enhancement and a hard X-ray (HXR) peak. Taking advantage of the spectroscopic observations of IRIS and Hinode/EIS, we measure the temporal variation of the plasma properties in the bright kernel in the chromosphere and corona. We find that explosive evaporation was observed when the WL emission occurred, even though the intensity enhancement in hotter lines is quite weak. The temporal correlation of the WL emission, HXR peak, and evaporation flows indicates that the WL emission was produced by accelerated electrons. To understand the WL emission process, we calculated the energy flux deposited by non-thermal electrons (observed by RHESSI) and compared it to the dissipated energy estimated from a chromospheric line (Mg II triplet) observed by IRIS. The deposited energy flux from the non-thermal electrons is about (3-7.7) × 1010 erg cm-2 s-1 for a given low-energy cutoff of 30-40 keV, assuming the thick-target model. The energy flux estimated from the changes in temperature in the chromosphere measured using the Mg II subordinate line is about (4.6-6.7) × 109 erg cm-2 s-1: ˜6%-22% of the deposited energy. This comparison of estimated energy fluxes implies that the continuum enhancement was directly produced by the non-thermal electrons.
Poster — Thur Eve — 55: An automated XML technique for isocentre verification on the Varian TrueBeam
DOE Office of Scientific and Technical Information (OSTI.GOV)
Asiev, Krum; Mullins, Joel; DeBlois, François
2014-08-15
Isocentre verification tests, such as the Winston-Lutz (WL) test, have gained popularity in the recent years as techniques such as stereotactic radiosurgery/radiotherapy (SRS/SRT) treatments are more commonly performed on radiotherapy linacs. These highly conformal treatments require frequent monitoring of the geometrical accuracy of the isocentre to ensure proper radiation delivery. At our clinic, the WL test is performed by acquiring with the EPID a collection of 8 images of a WL phantom fixed on the couch for various couch/gantry angles. This set of images is later analyzed to determine the isocentre size. The current work addresses the acquisition process. Amore » manual WL test acquisition performed by and experienced physicist takes in average 25 minutes and is prone to user manipulation errors. We have automated this acquisition on a Varian TrueBeam STx linac (Varian, Palo Alto, USA). The Varian developer mode allows the execution of custom-made XML script files to control all aspects of the linac operation. We have created an XML-WL script that cycles through each couch/gantry combinations taking an EPID image at each position. This automated acquisition is done in less than 4 minutes. The reproducibility of the method was verified by repeating the execution of the XML file 5 times. The analysis of the images showed variation of the isocenter size less than 0.1 mm along the X, Y and Z axes and compares favorably to a manual acquisition for which we typically observe variations up to 0.5 mm.« less
45. Building 102, view of waveguide "coaxial waste load" device ...
45. Building 102, view of waveguide "coaxial waste load" device connected to waveguide combiner. - Clear Air Force Station, Ballistic Missile Early Warning System Site II, One mile west of mile marker 293.5 on Parks Highway, 5 miles southwest of Anderson, Anderson, Denali Borough, AK
EXAFS/XANES studies of plutonium-loaded sodalite/glass waste forms
NASA Astrophysics Data System (ADS)
Richmann, Michael K.; Reed, Donald T.; Kropf, A. Jeremy; Aase, Scott B.; Lewis, Michele A.
2001-09-01
A sodalite/glass ceramic waste form is being developed to immobilize highly radioactive nuclear wastes in chloride form, as part of an electrochemical cleanup process. Two types of simulated waste forms were studied: where the plutonium was alone in an LiCl/KCl matrix and where simulated fission-product elements were added representative of the electrometallurgical treatment process used to recover uranium from spent nuclear fuel also containing plutonium and a variety of fission products. Extended X-ray absorption fine structure spectroscopy (EXAFS) and X-ray absorption near-edge spectroscopy (XANES) studies were performed to determine the location, oxidation state, and particle size of the plutonium within these waste form samples. Plutonium was found to segregate as plutonium(IV) oxide with a crystallite size of at least 4.8 nm in the non-fission-element case and 1.3 nm with fission elements present. No plutonium was observed within the sodalite in the waste form made from the plutonium-loaded LiCl/KCl eutectic salt. Up to 35% of the plutonium in the waste form made from the plutonium-loaded simulated fission-product salt may be segregated with a heavy-element nearest neighbor other than plutonium or occluded internally within the sodalite lattice.
Revision of endemic Marquesas Islands Bidens (Asteraceae, Coreopsideae)
Wagner, Warren L.; Clark, John R.; Lorence, David H.
2014-01-01
Abstract During the preparation of the Vascular Flora of the Marquesas Islands four new species of Bidens (Coreopsideae, Asteraceae) have come to light and are described herein: Bidens woodii W.L. Wagner, J.R. Clark & Lorence, sp. nov. from Ua Pou, and Bidens microcephala W.L. Wagner, J.R. Clark & Lorence sp. nov., Bidens evapelliana W.L. Wagner, J.R. Clark & Lorence, sp. nov., and Bidens wichmanii W.L. Wagner, J.R. Clark & Lorence, sp. nov. from the undercollected island of Fatu Hiva. In addition to these new species, we recognize the following six species of Bidens previously described from the Marquesas Islands: Bidens beckiana (F. Br.) Sherff (Eiao and Hatutaa), Bidens bipontina Sherff and Bidens cordifolia Sch. Bip. (both in Nuku Hiva), Bidens henryi Sherff (Hiva Oa, Tahuata), Bidens uapensis (F. Br.) Sherff (Ua Pou), and Bidens polycephala Sch. Bip. (Nuku Hiva, Ua Huku, Hiva Oa, Tahuata, and Mohotani). Two names are reduced to synonymy under Bidens polycephala: Bidens collina Degener & Sherff, syn. nov. and Bidens jardinii Sch. Bip., syn. nov. Bidens polycephala has the widest distribution of the Marquesan species on five of the islands and exhibits considerable variation. PMID:25009437
Hickethier, Tilman; Iuga, Andra-Iza; Lennartz, Simon; Hauger, Myriam; Byrtus, Jonathan; Luetkens, Julian A; Haneder, Stefan; Maintz, David; Doerner, Jonas
We aimed to determine optimal window settings for conventional polyenergetic (PolyE) and virtual monoenergetic images (MonoE) derived from abdominal portal venous phase computed tomography (CT) examinations on a novel dual-layer spectral-detector CT (SDCT). From 50 patients, SDCT data sets MonoE at 40 kiloelectron volt as well as PolyE were reconstructed and best individual window width and level values manually were assessed separately for evaluation of abdominal arteries as well as for liver lesions. Via regression analysis, optimized individual values were mathematically calculated. Subjective image quality parameters, vessel, and liver lesion diameters were measured to determine influences of different W/L settings. Attenuation and contrast-to-noise values were significantly higher in MonoE compared with PolyE. Compared with standard settings, almost all adjusted W/L settings varied significantly and yielded higher subjective scoring. No differences were found between manually adjusted and mathematically calculated W/L settings. PolyE and MonoE from abdominal portal venous phase SDCT examinations require appropriate W/L settings depending on reconstruction technique and assessment focus.
Duggan, J; Bates, M P; Phillips, C A
2001-06-01
The use of poultry waste as a fertiliser on arable land is an accepted method of waste treatment. However, run-off from such practices may result in contamination of the watercourse by human pathogens. In this study the effectiveness of using constructed wetlands as an alternative treatment for poultry manure waste was evaluated. Enumeration of Campylobacter spp., Escherichia coli, total coliforms and total aerobes were carried out on influent and effluent samples from reed beds loaded with poultry waste. For both sequential loading and continuous loading there was a statistically significant mean log reduction of 3.56 and 4.25 for E. coli, 3.2 and 3.88 for coliforms, 3.85 and 4.2 for total aerobic counts and 3.13 and 2.96 for Campylobacter spp., respectively. This method, which has been previously recognised as cost-effective and environmentally acceptable, provides an efficient method for reducing numbers of these bacteria in poultry waste and therefore an effective alternative treatment for such waste or waters containing run off from land previously spread with poultry manure.
Yap, Hwa Jen; Taha, Zahari; Md Dawal, Siti Zawiah; Chang, Siow-Wee
2014-01-01
Traditional robotic work cell design and programming are considered inefficient and outdated in current industrial and market demands. In this research, virtual reality (VR) technology is used to improve human-robot interface, whereby complicated commands or programming knowledge is not required. The proposed solution, known as VR-based Programming of a Robotic Work Cell (VR-Rocell), consists of two sub-programmes, which are VR-Robotic Work Cell Layout (VR-RoWL) and VR-based Robot Teaching System (VR-RoT). VR-RoWL is developed to assign the layout design for an industrial robotic work cell, whereby VR-RoT is developed to overcome safety issues and lack of trained personnel in robot programming. Simple and user-friendly interfaces are designed for inexperienced users to generate robot commands without damaging the robot or interrupting the production line. The user is able to attempt numerous times to attain an optimum solution. A case study is conducted in the Robotics Laboratory to assemble an electronics casing and it is found that the output models are compatible with commercial software without loss of information. Furthermore, the generated KUKA commands are workable when loaded into a commercial simulator. The operation of the actual robotic work cell shows that the errors may be due to the dynamics of the KUKA robot rather than the accuracy of the generated programme. Therefore, it is concluded that the virtual reality based solution approach can be implemented in an industrial robotic work cell. PMID:25360663
Yap, Hwa Jen; Taha, Zahari; Dawal, Siti Zawiah Md; Chang, Siow-Wee
2014-01-01
Traditional robotic work cell design and programming are considered inefficient and outdated in current industrial and market demands. In this research, virtual reality (VR) technology is used to improve human-robot interface, whereby complicated commands or programming knowledge is not required. The proposed solution, known as VR-based Programming of a Robotic Work Cell (VR-Rocell), consists of two sub-programmes, which are VR-Robotic Work Cell Layout (VR-RoWL) and VR-based Robot Teaching System (VR-RoT). VR-RoWL is developed to assign the layout design for an industrial robotic work cell, whereby VR-RoT is developed to overcome safety issues and lack of trained personnel in robot programming. Simple and user-friendly interfaces are designed for inexperienced users to generate robot commands without damaging the robot or interrupting the production line. The user is able to attempt numerous times to attain an optimum solution. A case study is conducted in the Robotics Laboratory to assemble an electronics casing and it is found that the output models are compatible with commercial software without loss of information. Furthermore, the generated KUKA commands are workable when loaded into a commercial simulator. The operation of the actual robotic work cell shows that the errors may be due to the dynamics of the KUKA robot rather than the accuracy of the generated programme. Therefore, it is concluded that the virtual reality based solution approach can be implemented in an industrial robotic work cell.
Bauer, Daniel P.; Steele, Timothy Doak; Anderson, Richard D.
1978-01-01
An analysis of the waste-load assimilative capacity of the Yampa River from Steamboat Springs to Hayden, Colo., a distance of 38 miles, was made during September 1975 to obtain information on the effects of projected waste loadings on this stream reach. Simulations of effects of waste loadings on streamflow quality were made using a steady-state water-quality model. The simulations were based on 7-day low-flow values with a 10-year recurrence interval and population projections for 2010. Model results for December and September streamflow conditions indicated that the recommended 1978 Colorado and 1976 U.S. Environmental Protection Agency water-quality standard of 0.02 milligram per liter for nonionized ammonia concentration would be exceeded. Model simulations also included the effect of a flow augmentation of 20 cubic feet per second from a proposed upstream reservoir. The permissible ammonia loading in the study reach could be increased approximately 25 percent with this amount of flow augmentation. Simulations of concentrations of dissolved oxygen, fecal-coliform bacteria, and nitrate nitrogen indicated that the State 's water-quality goals proposed for 1978, 1983, or 1985 would not be exceeded. (Woodard-USGS)
A FIB/TEM Study of a Complex Wark-Lovering Rim on a Vigarano CAI
NASA Technical Reports Server (NTRS)
Keller, L. P.; Needham, A. W.; Messenger, S.
2013-01-01
Wark-Lovering (WL) rims are thin multilayered mineral sequences that surround most Ca, Al-rich inclusions (CAIs). Several processes have been proposed for WL rim formation, including condensation, flash-heating or reaction with a nebular reservoir, or combinations of these [e.g. 1-7], but no consensus exists. Our previous coordinated transmission electron microscope (TEM) and NanoSIMS O isotopic measurements showed that a WL rim experienced flash heating events in a nebular environment with planetary O isotopic composition, distinct from the (16)O-rich formation environment [6]. Our efforts have focused on CAIs from the CV(sub red) chondrites, especially Vigarano, because these have escaped much of the parent body alteration effects that are common in CAIs from CV(sub ox) group.
NASA Astrophysics Data System (ADS)
Ilahi, Bouraoui; Al-Saigh, Reem; Salem, Bassem
2017-07-01
The effects of the wetting layer thickness (t WL) on the electronic properties of direct band gap type-I strained dome shaped Ge(1-x)Sn x quantum dot (QD) embedded in Ge matrix is numerically studied. The emission wavelength and the energy difference between S and P electron levels have been evaluated as a function of t WL for different QD size and composition with constant height to diameter ratio. The emission wavelength is found to be red shifted by increasing the wetting layer thickness, with smaller size QD being more sensitive to the variation of t WL. Furthermore, the minimum Sn composition required to fit the directness criteria is found to reduce by increasing the wetting layer thickness.
Conceptual waste packaging options for deep borehole disposal
DOE Office of Scientific and Technical Information (OSTI.GOV)
Su, Jiann -Cherng; Hardin, Ernest L.
This report presents four concepts for packaging of radioactive waste for disposal in deep boreholes. Two of these are reference-size packages (11 inch outer diameter) and two are smaller (5 inch) for disposal of Cs/Sr capsules. All four have an assumed length of approximately 18.5 feet, which allows the internal length of the waste volume to be 16.4 feet. However, package length and volume can be scaled by changing the length of the middle, tubular section. The materials proposed for use are low-alloy steels, commonly used in the oil-and-gas industry. Threaded connections between packages, and internal threads used to sealmore » the waste cavity, are common oilfield types. Two types of fill ports are proposed: flask-type and internal-flush. All four package design concepts would withstand hydrostatic pressure of 9,600 psi, with factor safety 2.0. The combined loading condition includes axial tension and compression from the weight of a string or stack of packages in the disposal borehole, either during lower and emplacement of a string, or after stacking of multiple packages emplaced singly. Combined loading also includes bending that may occur during emplacement, particularly for a string of packages threaded together. Flask-type packages would be fabricated and heat-treated, if necessary, before loading waste. The fill port would be narrower than the waste cavity inner diameter, so the flask type is suitable for directly loading bulk granular waste, or loading slim waste canisters (e.g., containing Cs/Sr capsules) that fit through the port. The fill port would be sealed with a tapered, threaded plug, with a welded cover plate (welded after loading). Threaded connections between packages and between packages and a drill string, would be standard drill pipe threads. The internal flush packaging concepts would use semi-flush oilfield tubing, which is internally flush but has a slight external upset at the joints. This type of tubing can be obtained with premium, low-profile threaded connections at each end. The internal-flush design would be suitable for loading waste that arrives from the originating site in weld-sealed, cylindrical canisters. Internal, tapered plugs with sealing filet welds would seal the tubing at each end. The taper would be precisely machined onto both the tubing and the plug, producing a metal-metal sealing surface that is compressed as the package is subjected to hydrostatic pressure. The lower plug would be welded in place before loading, while the upper plug would be placed and welded after loading. Conceptual Waste Packaging Options for Deep Borehole Disposal July 30, 2015 iv Threaded connections between packages would allow emplacement singly or in strings screwed together at the disposal site. For emplacement on a drill string the drill pipe would be connected directly into the top package of a string (using an adapter sub to mate with premium semi-flush tubing threads). Alternatively, for wireline emplacement the same package designs could be emplaced singly using a sub with wireline latch, on the upper end. Threaded connections on the bottom of the lowermost package would allow attachment of a crush box, instrumentation, etc.« less
Ductility of polystyrene waste panel
NASA Astrophysics Data System (ADS)
Sulistyorini, Dewi; Yasin, Iskandar
2018-03-01
Polystyrene waste panel is one of alternative materials that uses polystyrene waste. This experiment is to utilize the polystyrene waste as a non structural panel to be evaluated the ductility. The specimen consisted of cement 250 kg/m3, polystyrene waste was as aggregate, water cement ratio was 0.4 and wire mesh diameter was 0.6 mm with the grid 6 mm × 6 mm placed on the top and bottom of the panels. The polystyrene panels were compressed at 2 MPa. Six specimens had dimension 80 cm length, 30 cm width and the thickness planned were two varieties, they were 0.5 cm and 1 cm. Flexural testing is used to examine load and deflection to measure the ductility. The load and the deflection showed that the maximum load for the specimen with 0.5 cm thickness is 0.4, 0.56 and 0.37. And for 1 cm thickness is 0.4, 0.36, 0.64. It shows that the thickness variation does not give effect on the maximum load. Result showed the average of Displacement Ductility Index of polystyrene waste panels with 0.5 cm thickness was 1.692 and for 1 cm thickness, the average was 4.043. So the average of the panel with 0.5 cm thickness planned is under 1.99 and the panel with 1 cm thickness planned is upper 3, therefore, it is considered imperative for adequate ductility.
Romaratezabala, Estibaliz; Nakamura, Fábio Yuzo; Castillo, Daniel; Gorostegi-Anduaga, Ilargi; Yanci, Javier
2018-01-01
The purpose of the study was to analyse the effect of two warm-up protocols of different duration on physical performance, perceived load and perception of being ready for a match in handball players. Eighteen handball players were randomly divided into two groups (Wup 34min , warm-up protocol of 34 min, Wup 17min , warm-up protocol of 17 min). Before and after the warm-up protocols, they performed a battery of physical tests and recorded their perception of feeling ready for a match. At the end of the warm-up protocols, all the players evaluated their differentiated perceived effort (dRPE). The results showed that neither of the protocols significantly modified (p > 0.05) the players' physical performance. However, the Wup 34min group showed higher values in the differentiated warm-up perceived load (dRPE-WL) (p < 0.01, TE = 0.97-1.27, high) than the Wup 17min group. The players with a greater perceived muscular load (RPE MUSC ) experienced a greater decrease in their acceleration capacity (r = 0.48-0.49, p < 0.05). In spite of the fact that neither of the warm-up protocols significantly modified the players' physical performance, a greater perceived muscular load may cause a greater decrease in acceleration capacity.
Federal Register 2010, 2011, 2012, 2013, 2014
2010-07-01
... 0.75 inch to 11.8 inches in length at the buttock line 61, between water line (WL) 220 and WL 228..., and between 10,685 total flight cycles and 29,357 total flight cycles. The cracking is attributed to..., in addition to normal pressurization cycles. Material analysis revealed multiple crack initiation...
Comparative analysis of the development of wing-flapping and flight in the fowl.
Provine, R R; Strawbridge, C L; Harrison, B J
1984-01-01
The development of wing-flapping rate, lateral flight, wing area, and the ratio of wing area to body weight are described in the Japanese quail (Coturnix coturnix japonica) and three chickens (Gallus gallus) to determine common developmental phenomena and to assess the effects of domestication. The chickens were the White Leghorn (a commercial egg producer), the Cornish X Rock (a commercial meat producer), and the Red Jungle fowl (the probable ancestor of domestic chickens). All birds performed drop-evoked wing-flapping on the day of hatching, at least 1 week before lateral flight was possible. Flapping rate of chickens doubled between hatching (approximately 4-6 Hz) and 13 days (approximately 9-12 Hz), after which it leveled off. Japanese quail (JQ) maintained a high flapping rate (approximately 11-13 Hz) during the 21 days after hatching. The Jungle fowl (JF) and JQ flapped the fastest and the White Leghorn (WL) and Cornish X Rock (CR) chickens flapped the slowest. The JF, WL, and JQ developed lateral flight at 7-9 days. The CR first flew 1-2 weeks later but subsequently became flightless. The WL, JF, and JQ had similar ratios of wing area to body weight; the ratios increased to a peak at 11-15 days and later declined. The ratio of the very heavy, essentially flightless, CR was approximately one-half that of the flighted JQ, WL, and JF. The wing-flapping frequencies of the domestic WL and CR chickens approximated that of the JF, suggesting that domestication did not affect the motor pattern generator for flight. The artificial selection of the CR for high body weight drastically diminished its flight performance by producing an unfavorable ratio of wing area to body weight. The JF and the domestic WL both flew well and had similar ratios. Domestication affected flight performance but not the neural circuitry producing wing-flapping. The central nervous system is much more conservative in its response to selection than the peripheral effector structures that it drives.
Cirilli, Marco; Bellincontro, Andrea; De Santis, Diana; Botondi, Rinaldo; Colao, Maria Chiara; Muleo, Rosario; Mencarelli, Fabio
2012-05-01
Clusters of Aleatico wine grape were picked at 18°Brix and placed at 10, 20, or 30°C, 45% relative humidity (RH) and 1.5m/s of air flow to dehydrate the berries up to 40% of loss of initial fresh weight. Sampling was done at 0%, 10%, 20%, 30%, and 40% weight loss (wl). ADH (alcohol dehydrogenase) gene expression, enzyme activity, and related metabolites were analysed. At 10°C, acetaldehyde increased rapidly and then declined, while ethanol continued to rise. At 20°C, acetaldehyde and ethanol increased significantly with the same pattern and declined at 40%wl. At 30°C, acetaldehyde did not increase but ethanol increased rapidly already at 10%wl. At the latter temperature, a significant increase in acetic acid and ethyl acetate occurred, while at 10°C their values were low. At 30°C, the ADH activity (ethanol to acetaldehyde direction), increased rapidly but acetaldehyde did not rise because of its oxidation to acetic acid, which increased together with ethyl acetate. At 10°C, the ADH activity increased at 20%wl and continued to rise even at 40%wl, meaning that ethanol oxidation was delayed. At 20°C, the behaviour was intermediate to the other temperatures. The relative expression of the VvAdh2 gene was the highest at 10°C already at 10%wl in a synchrony with the ADH activity, indicating a rapid response likely due to low temperature. The expression subsequently declined. At 20 and 30°C, the expression was lower and increased slightly during dehydration in combination with the ADH activity. This imbalance between gene expression and ADH activity at 10°C, as well as the unexpected expression of the carotenoid cleavage dioxygenase 1 (CCD1) gene, opens the discussion on the stress sensitivity and transcription event during postharvest dehydration, and the importance of carefully monitoring temperature during dehydration. Copyright © 2011 Elsevier Ltd. All rights reserved.
Ponce, Jaime; Taheri, Shahrad; Lusco, Vincent; Cornell, Christopher; Ng-Mak, Daisy S; Shi, Rui; Okerson, Ted
2014-05-01
This 48 week combined analysis reports safety and clinical effectiveness of the LAP-BAND AP * laparoscopic adjustable gastric band (LAGB) in severely obese patients enrolled in the 5 year, prospective, observational, open-label APEX (NCT00501085) and HERO (NCT00953173) studies. The studies enrolled 1620 patients (APEX: N = 514; HERO: N = 1106), 1140 patients in the US (including all APEX patients), and 480 patients in the European Union (EU), Canada or Australia. APEX and HERO are non-randomized, non-comparator, open-label studies with differences in study management practices and follow-up. Notably, laboratory data were not collected during the APEX study. After 48 weeks, mean (SD) percentage weight loss (%WL) was for APEX: 18.7% (7.9); HERO-US: 17.9% (8.5); HERO-EU: 16.5% (10.3); HERO-Canada: 13.4% (8.9); and HERO-Australia: 12.3% (6.9). After 48 weeks, there were no significant differences in %WL for APEX vs. HERO-US. After 48 weeks in the combined analysis (APEX + HERO): (1) patients without vs. with type 2 diabetes at baseline had greater %WL (18% [8.7] vs. 16% [8.5], p = 0.002); (2) female patients had greater %WL vs. male patients (17.9% [8.5] vs. 15.9% [9.3], p = 0.003); (3) younger patients had greater %WL vs. older patients (<50 years: 17.8% [8.7] vs. ≥50 years: 16.7% [8.6], p = 0.035); (4) baseline BMI did not affect %WL (≤35 to ≤45 kg/m(2): 17.7% [8.4] vs. >45 kg/m(2): 17.1% [9.1], p = 0.272). Device-related serious adverse events and adverse events were reported in 1.9% and 17.7% of patients, respectively. Revision and explantation surgeries were carried out on 3.4% and 2.3% of patients, respectively during the 48 weeks of follow-up. This analysis demonstrates the effective weight loss and safety profile of the current LAGB system, with US patients achieving better weight loss than patients from outside the US.
Kovacs, Agnes Zsofia; Molnar, Miklos Zsolt; Szeifert, Lilla; Ambrus, Csaba; Molnar-Varga, Marta; Szentkiralyi, Andras; Mucsi, Istvan; Novak, Marta
2011-03-01
Kidney transplantation is believed to improve health-related quality of life (HRQoL) of patients requiring renal replacement therapy (RRT). Recent studies suggested that the observed difference in HRQoL between kidney transplant recipients (Tx) vs patients treated with dialysis may reflect differences in patient characteristics. We tested if Tx patients have better HRQoL compared to waitlisted (WL) patients treated with dialysis after extensive adjustment for covariables. Eight hundred and eighty-eight prevalent Tx patients followed at a single outpatient transplant clinic and 187 WL patients treated with maintenance dialysis in nine dialysis centres were enrolled in this observational cross-sectional study. Data about socio-demographic and clinical parameters, self-reported depressive symptoms and the most frequent sleep disorders assessed by self-reported questionnaires were collected at enrollment. HRQoL was assessed by the Kidney Disease Quality of Life Questionnaire. Patient characteristics were similar in the Tx vs WL groups: the proportion of males (58 vs 60%), mean ± SD age (49 ± 13 vs 49 ± 12) and proportion of diabetics (17 vs 18%), respectively, were all similar. Tx patients had significantly better HRQoL scores compared to the WL group both in generic (Physical function, General health perceptions, Energy/fatigue, Emotional well-being) and in kidney disease-specific domains (Symptoms/problems, Effect- and Burden of kidney disease and Sleep). In multivariate regression models adjusting for clinical and socio-demographic characteristics, sleep disorders and depressive symptoms, the modality of RRT (WL vs Tx) remained independently associated with three (General health perceptions, Effect- and Burden of kidney disease) out of the eight HRQoL dimensions analysed. Kidney Tx recipients have significantly better HRQoL compared to WL dialysis patients in some, but not all, dimensions of quality of life after accounting for differences in patient characteristics. Utilizing multidimensional disease-specific questionnaires will allow better understanding of treatment, disease and patient-related factors potentially affecting quality of life in patients with chronic medical conditions.
Du, Weiliang; Johnson, Jennifer L; Jiang, Wei; Kudchadker, Rajat J
2016-01-08
In Winston-Lutz (WL) tests, the isocenter of a linear accelerator (linac) is determined as the intersection of radiation central axes (CAX) from multiple gantry, collimator, and couch angles. It is well known that the CAX can wobble due to mechanical imperfections of the linac. Previous studies suggested that the wobble varies with gantry and collimator angles. Therefore, the isocenter determined in the WL tests has a profound dependence on the gantry and collimator angles at which CAX are sampled. In this study, we evaluated the systematic and random errors in the iso-centers determined with different CAX sampling schemes. Digital WL tests were performed on six linacs. For each WL test, 63 CAX were sampled at nine gantry angles and seven collimator angles. Subsets of these data were used to simulate the effects of various CAX sampling schemes. An isocenter was calculated from each subset of CAX and compared against the reference isocenter, which was calculated from 48 opposing CAX. The differences between the calculated isocenters and the reference isocenters ranged from 0 to 0.8 mm. The differences diminished to less than 0.2 mm when 24 or more CAX were sampled. Isocenters determined with collimator 0° were vertically lower than those determined with collimator 90° and 270°. Isocenter localization errors in the longitudinal direction (along the axis of gantry rotation) showed a strong dependence on the collimator angle selected. The errors in all directions were significantly reduced when opposing collimator angles and opposing gantry angles were employed. The isocenter localization errors were less than 0.2 mm with the common CAX sampling scheme, which used four cardinal gantry angles and two opposing collimator angles. Reproducibility stud-ies on one linac showed that the mean and maximum variations of CAX during the WL tests were 0.053 mm and 0.30 mm, respectively. The maximal variation in the resulting isocenters was 0.068 mm if 48 CAX were used, or 0.13 mm if four CAX were used. Quantitative results from this study are useful for understanding and minimizing the isocenter uncertainty in WL tests.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Fox, K. M.
The U.S. Department of Energy (DOE), Office of Environmental Management (EM) is sponsoring an international, collaborative project to develop a fundamental model for sulfate solubility in nuclear waste glass. The solubility of sulfate has a significant impact on the achievable waste loading for nuclear waste forms within the DOE complex. These wastes can contain relatively high concentrations of sulfate, which has low solubility in borosilicate glass. This is a significant issue for low-activity waste (LAW) glass and is projected to have a major impact on the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Sulfate solubility has also been amore » limiting factor for recent high level waste (HLW) sludge processed at the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF). The low solubility of sulfate in glass, along with melter and off-gas corrosion constraints, dictate that the waste be blended with lower sulfate concentration waste sources or washed to remove sulfate prior to vitrification. The development of enhanced borosilicate glass compositions with improved sulfate solubility will allow for higher waste loadings and accelerate mission completion.The objective of the current scope being pursued by SHU is to mature the sulfate solubility model to the point where it can be used to guide glass composition development for DWPF and WTP, allowing for enhanced waste loadings and waste throughput at these facilities. A series of targeted glass compositions was selected to resolve data gaps in the model and is identified as Stage III. SHU fabricated these glasses and sent samples to SRNL for chemical composition analysis. SHU will use the resulting data to enhance the sulfate solubility model and resolve any deficiencies. In this report, SRNL provides chemical analyses for the Stage III, simulated HLW glasses fabricated by SHU in support of the sulfate solubility model development.« less
NASA Astrophysics Data System (ADS)
Petrie, Gordon; Kopp, Greg; Harvey, J. W.
2014-06-01
The NSO’s GONG network produces “white light” (WL) continuum intensity images from one-minute integrations averaged across a 0. Å wide band pass centered at 676 Å at one minute cadence using six sites worldwide. Clear WL signatures of solar flares are present in GONG intensity data for only the largest flares because of low spatial resolution (2.5 arcsec pixel size). For six major flares (GOES class X6.5 - X28) observed by GONG, we compare integrated GONG full-disk WL intensity curves with SORCE/TIM total solar irradiance (TSI) measurements. Distinctive p-mode signatures are evident in both GONG and SORCE time series, though the correlation between GONG and SORCE data varies from flare to flare. In some cases a clear TSI peak and an interruption of the GONG p-mode pattern accompany the flare. The flare signature is generally weaker in the GONG data, suggesting that most of the TIM flare signal arises from wavelengths shorter than the GONG band pass. The flare kernels nevertheless are clear and last many minutes in the spatially resolved GONG image time series. We also compare the GONG active region intensity observations with shorter-wavelength data. In one case observed by TRACE, the GONG and TRACE WL curves are very similar and the TRACE 160 Å curve shows a significant precursor and a long tail. In most cases the GONG WL and RHESSI 25-100 keV counts appear well correlated in time. This work utilizes GONG data obtained by the NSO Integrated Synoptic Program (NISP), managed by the National Solar Observatory, which is operated by AURA, Inc. under a cooperative agreement with the National Science Foundation.
Analysis of the width ratio and wear rate of maxillary anterior teeth in the Korean population.
Oh, Yeon-Ah; Yang, Hong-So; Park, Sang-Won; Lim, Hyun-Pil; Yun, Kwi-Dug; Park, Chan
2017-04-01
The purpose of this study was to compare the width ratio of maxillary anterior teeth according to age in the Korean population and to evaluate the maxillary central incisor width-to-length (W/L) ratio, given differences in age and gender. Ninety-three Korean adults were divided into 3 groups (n = 31) by age. Group I was 20 - 39 years old, Group II was 40 - 59 years old, and Group III was over 60 years of age. After taking an impression and a cast model of the maxillary arch, the anterior teeth width ratio and central incisor W/L ratio were calculated from standard digital images of the cast models using a graph paper with a digital single lens reflex (DSLR) camera. The calculated ratios were compared among all groups and central incisor W/L ratio were analyzed according to age and gender. All comparative data were statistically analyzed with one-sample t-tests, one-way ANOVAs with Tukey tests, and independent t-tests. No significant differences in maxillary anterior teeth ratios were found among the age groups. The maxillary central incisor W/L ratios in Group III were the greatest and were significantly higher than those in the other groups. The central incisor W/L ratio of men was higher than that of women in Group II. Maxillary anterior teeth width ratios were similar in all age groups in the Korean population. The maxillary central incisor was observed as worn teeth in the group over 60 years of age, and a significant difference between genders was found in 40 to 50 year olds.
Kilpela, Lisa Smith; Blomquist, Kerstin; Verzijl, Christina; Wilfred, Salomé; Beyl, Robbie; Becker, Carolyn Black
2016-06-01
The Body Project is a cognitive dissonance-based body image improvement program with ample research support among female samples. More recently, researchers have highlighted the extent of male body dissatisfaction and disordered eating behaviors; however, boys/men have not been included in the majority of body image improvement programs. This study aims to explore the efficacy of a mixed-gender Body Project compared with the historically female-only body image intervention program. Participants included male and female college students (N = 185) across two sites. We randomly assigned women to a mixed-gender modification of the two-session, peer-led Body Project (MG), the two-session, peer-led, female-only (FO) Body Project, or a waitlist control (WL), and men to either MG or WL. Participants completed self-report measures assessing negative affect, appearance-ideal internalization, body satisfaction, and eating disorder pathology at baseline, post-test, and at 2- and 6-month follow-up. Linear mixed effects modeling to estimate the change from baseline over time for each dependent variable across conditions were used. For women, results were mixed regarding post-intervention improvement compared with WL, and were largely non-significant compared with WL at 6-month follow-up. Alternatively, results indicated that men in MG consistently improved compared with WL through 6-month follow-up on all measures except negative affect and appearance-ideal internalization. Results differed markedly between female and male samples, and were more promising for men than for women. Various explanations are provided, and further research is warranted prior to drawing firm conclusions regarding mixed-gender programming of the Body Project. © 2016 Wiley Periodicals, Inc.(Int J Eat Disord 2016; 49:591-602). © 2016 Wiley Periodicals, Inc.
Serra, Monica C; Blumenthal, Jacob B; Addison, Odessa R; Miller, Ann J; Goldberg, Andrew P; Ryan, Alice S
2017-01-01
The purpose was to determine whether lifestyle interventions have different effects on regional fat in women with normal glucose tolerance vs. impaired glucose tolerance (NGT vs. IGT). Changes in glucose metabolism (2-h oral glucose-tolerance tests), android to gynoid fat mass ratio (dual energy X-ray absorptiometry [DXA]), visceral to subcutaneous abdominal fat area ratio (CT), and abdominal to gluteal subcutaneous fat cell weight (FCW; adipose tissue biopsies) were determined in 60 overweight postmenopausal women (45-80 years) following 6 months of weight loss alone (WL; n = 28) or with aerobic exercise (AEX + WL; n = 32). The interventions led to ∼8% decrease in weight, but only the AEX + WL group improved fitness (↑11% in VO2max) and reduced the android-to-gynoid fat mass ratio (↓5%; p < 0.05). Both NGT and IGT groups reduced visceral and subcutaneous abdominal fat areas and abdominal and gluteal FCWs, which related to improvements in homeostatic model assessment (r = 0.34-0.42) and 2-h glucose (r = 0.34-0.35), respectively (p < 0.05). The decline in FCW was 2× greater in women with IGT following WL (p < 0.05). The ratios of abdominal-to-gluteal FCW did not change following either intervention. The mechanisms by which WL with and without exercise impact regional fat loss should be explored as reductions in abdominal fat area and subcutaneous FCW appear to influence glucose metabolism. This is a work of the U.S. Government and is not subject to copyright protection in the United States. Foreign copyrights may apply. Published by S. Karger AG, Basel.
Calorie Estimation in Adults Differing in Body Weight Class and Weight Loss Status.
Brown, Ruth E; Canning, Karissa L; Fung, Michael; Jiandani, Dishay; Riddell, Michael C; Macpherson, Alison K; Kuk, Jennifer L
2016-03-01
Ability to accurately estimate calories is important for weight management, yet few studies have investigated whether individuals can accurately estimate calories during exercise or in a meal. The objective of this study was to determine if accuracy of estimation of moderate or vigorous exercise energy expenditure and calories in food is associated with body weight class or weight loss status. Fifty-eight adults who were either normal weight (NW) or overweight (OW), and either attempting (WL) or not attempting weight loss (noWL), exercised on a treadmill at a moderate (60% HRmax) and a vigorous intensity (75% HRmax) for 25 min. Subsequently, participants estimated the number of calories they expended through exercise and created a meal that they believed to be calorically equivalent to the exercise energy expenditure. The mean difference between estimated and measured calories in exercise and food did not differ within or between groups after moderate exercise. After vigorous exercise, OW-noWL overestimated energy expenditure by 72% and overestimated the calories in their food by 37% (P < 0.05). OW-noWL also significantly overestimated exercise energy expenditure compared with all other groups (P < 0.05) and significantly overestimated calories in food compared with both WL groups (P < 0.05). However, among all groups, there was a considerable range of overestimation and underestimation (-280 to +702 kcal), as reflected by the large and statistically significant absolute error in calorie estimation of exercise and food. There was a wide range of underestimation and overestimation of calories during exercise and in a meal. Error in calorie estimation may be greater in overweight adults who are not attempting weight loss.
Calorie Estimation in Adults Differing in Body Weight Class and Weight Loss Status
Brown, Ruth E; Canning, Karissa L; Fung, Michael; Jiandani, Dishay; Riddell, Michael C; Macpherson, Alison K; Kuk, Jennifer L
2016-01-01
Purpose Ability to accurately estimate calories is important for weight management, yet few studies have investigated whether individuals can accurately estimate calories during exercise, or in a meal. The objective of this study was to determine if accuracy of estimation of moderate or vigorous exercise energy expenditure and calories in food is associated with body weight class or weight loss status. Methods Fifty-eight adults who were either normal weight (NW) or overweight (OW), and either attempting (WL) or not attempting weight loss (noWL), exercised on a treadmill at a moderate (60% HRmax) and a vigorous intensity (75% HRmax) for 25 minutes. Subsequently, participants estimated the number of calories they expended through exercise, and created a meal that they believed to be calorically equivalent to the exercise energy expenditure. Results The mean difference between estimated and measured calories in exercise and food did not differ within or between groups following moderate exercise. Following vigorous exercise, OW-noWL overestimated energy expenditure by 72%, and overestimated the calories in their food by 37% (P<0.05). OW-noWL also significantly overestimated exercise energy expenditure compared to all other groups (P<0.05), and significantly overestimated calories in food compared to both WL groups (P<0.05). However, among all groups there was a considerable range of over and underestimation (−280 kcal to +702 kcal), as reflected by the large and statistically significant absolute error in calorie estimation of exercise and food. Conclusion There was a wide range of under and overestimation of calories during exercise and in a meal. Error in calorie estimation may be greater in overweight adults who are not attempting weight loss. PMID:26469988
Pierie, Jean-Pierre E N; Muzikansky, Alona; Tanabe, Kenneth K; Ott, Mark J
2005-07-01
Optimal management of patients with hepatocellular carcinoma (HCC) is controversial. This study was conducted to evaluate the outcome of tumor resection versus assignment to a liver transplant waiting list (WL) in patients with HCC. Prospectively collected patient data from 1970 to 1997 on 313 patients with HCC were retrospectively analyzed by multivariate analysis to determine the effect of liver disease, method of treatment, and tumor-related factors on survival. A total of 199 patients underwent nonsurgical palliative care (PC), 81 underwent partial liver resection (LR), and 33 were assigned to a liver transplant WL, of which 22 received a donor liver. A total of 91%, 53%, and 91% of the patients had cirrhotic livers in the PC, LR, and WL groups, respectively (P < .001). In the LR group, the absence of a tumor capsule (P < .0001) and a poorly differentiated tumor (P = .027) were both adverse prognostic factors. In the WL group, hepatitis B (P = .02) and American Joint Committee on Cancer tumor stage III (P = .019) were adverse prognostic factors. The 3-year survival rates were 4%, 33%, and 38% for the PC, LR, and WL patients, respectively (P < .0001). The 3-year survival rate in the LR patients was 51% in patients without cirrhosis and 15% in patients with cirrhosis (P < .0001). Patients with locally unresectable tumors, distant disease, or both will continue to receive PC. Patients assigned to liver transplant WLs run the risk of not receiving a donor liver, in which case their survival is predicted to be poor. Survival after resection in a group of patients with advanced tumors is worse than that after transplantation; however, shortages of donor livers presently preclude transplantation in this population of patients.
Bajerska, Joanna; Mildner-Szkudlarz, Sylwia; Walkowiak, Jarosław
2015-06-01
We examined whether the incorporation of green tea extract enriched rye bread (GTRB) into the diet can improve weight loss (WL) maintenance and control of abnormalities linked to metabolic syndrome (MS). A total of 55 obese men and women (mean age: 53.0±7.0 years, body mass index: 35.0±5.5 kg m(-2)) were recruited. The study had a single-blind randomized study design and consisted of an 8-week WL phase with low-energy calorie diet, followed by a 12-week weight maintenance (WM) phase. During the WM phase, the subjects were randomized into two groups, receiving either the control rye bread (control group) or the GTRB (intervention group). The ingestion of 280 and 360 g GTRB provided daily totals of 123.2 and 158.4 mg caffeine, and 188.3 and 242.1 mg of epigallocatechin gallate, for women and men, respectively. After the WL phase, subjects lost 7.3±3.1 kg of their baseline body weight. GTRB intake did not significantly influence the maintenance of WL, high-density lipoprotein-cholesterol, triglycerides, and glucose concentrations. Although, it resulted in significant differences (mean difference [95% confidence interval]) between the treatment groups in the maintenance of waist circumference (-1.22 cm [-2.4, -0.02; P=.04]), the results were not clinically meaningful. Nevertheless, the ingestion of GTRB led to the maintenance of lower blood pressure (BP), also the proportion of subjects fulfilling the criteria of MS after the WM phase was lower in the intervention group than in the control group. Although GTRB consumption did not improve significantly the WL maintenance, it resulted in a better control of BP.
Kayes, Gillyanne; Welch, Graham F
2017-05-01
Using an empirical design, this study investigated perceptual and acoustic differences between the recorded vocal products of songs and scales of professional female singers of classical Western Lyric (WL) and non-legit Musical Theater (MT) styles. A total of 54 audio-recorded samples of songs and scales from professional female singers were rated in a blind randomized testing process by seven expert listeners as being performed by either a WL or MT singer. Songs and scales that were accurately perceived by genre were then analyzed intra- and inter-genre using long-term average spectrum analysis. A high level of agreement was found between judges in ratings for both songs and scales according to genre (P < 0.0001). Judges were more successful in locating WL than MT, but accuracy was always >50%. For the long-term average spectrum analysis intra-genre, song and scale matched better than chance. The highest spectral peak for the WL singers was at the mean fundamental frequency, whereas this spectral area was weaker for the MT singers, who showed a marked peak at 1 kHz. The other main inter-genre difference appeared in the higher frequency region, with a peak in the MT spectrum between 4 and 5 kHz-the region of the "speaker's formant." In comparing female singers of WL and MT styles, scales as well as song tasks appear to be indicative of singer genre behavior. This implied difference in vocal production may be useful to teachers and clinicians dealing with multiple genres. The addition of a scale-in-genre task may be useful in future research seeking to identify genre-distinctive behaviors. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Lee, Kyoung-Sun; Imada, Shinsuke; Watanabe, Kyoko
An X1.6 flare occurred in active region AR 12192 on 2014 October 22 at 14:02 UT and was observed by Hinode , IRIS , SDO , and RHESSI . We analyze a bright kernel that produces a white light (WL) flare with continuum enhancement and a hard X-ray (HXR) peak. Taking advantage of the spectroscopic observations of IRIS and Hinode /EIS, we measure the temporal variation of the plasma properties in the bright kernel in the chromosphere and corona. We find that explosive evaporation was observed when the WL emission occurred, even though the intensity enhancement in hotter lines ismore » quite weak. The temporal correlation of the WL emission, HXR peak, and evaporation flows indicates that the WL emission was produced by accelerated electrons. To understand the WL emission process, we calculated the energy flux deposited by non-thermal electrons (observed by RHESSI ) and compared it to the dissipated energy estimated from a chromospheric line (Mg ii triplet) observed by IRIS . The deposited energy flux from the non-thermal electrons is about (3–7.7) × 10{sup 10} erg cm{sup −2} s{sup −1} for a given low-energy cutoff of 30–40 keV, assuming the thick-target model. The energy flux estimated from the changes in temperature in the chromosphere measured using the Mg ii subordinate line is about (4.6–6.7) × 10{sup 9} erg cm{sup −2} s{sup −1}: ∼6%–22% of the deposited energy. This comparison of estimated energy fluxes implies that the continuum enhancement was directly produced by the non-thermal electrons.« less
Characteristics that Produce White-light Enhancements in Solar Flares Observed by Hinode/SOT
NASA Astrophysics Data System (ADS)
Watanabe, Kyoko; Kitagawa, Jun; Masuda, Satoshi
2017-12-01
To understand the conditions that produce white-light (WL) enhancements in solar flares, a statistical analysis of visible continuum data as observed by Hinode/Solar Optical Telescope (SOT) was performed. In this study, approximately 100 flare events from M- and X-class flares were selected. The time period during which the data were recorded spans from 2011 January to 2016 February. Of these events, approximately half are classified as white-light flares (WLFs), whereas the remaining events do not show any enhancements of the visible continuum (non-WLF; NWL). To determine the existence of WL emission, running difference images of not only the Hinode/SOT WL (G-band, blue, green, and red filter) data, but also the Solar Dynamics Observatory/Helioseismic and Magnetic Imager continuum data are used. A comparison between these two groups of WL data in terms of duration, temperature, emission measure of GOES soft X-rays, distance between EUV flare ribbons, strength of hard X-rays, and photospheric magnetic field strength was undertaken. In this statistical study, WLF events are characterized by a shorter timescale and shorter ribbon distance compared with NWL events. From the scatter plots of the duration of soft X-rays and the energy of non-thermal electrons, a clear distinction between WLF and NWL events can be made. It is found that the precipitation of large amounts of accelerated electrons within a short time period plays a key role in generating WL enhancements. Finally, it was demonstrated that the coronal magnetic field strength in the flare region is one of the most important factors that allow the individual identification of WLF events from NWL events.
Pinilla, Jaime; López-Valcárcel, Beatriz G; González-Martel, Christian; Peiro, Salvador
2018-05-09
Newcomb-Benford's Law (NBL) proposes a regular distribution for first digits, second digits and digit combinations applicable to many different naturally occurring sources of data. Testing deviations from NBL is used in many datasets as a screening tool for identifying data trustworthiness problems. This study aims to compare public available waiting lists (WL) data from Finland and Spain for testing NBL as an instrument to flag up potential manipulation in WLs. Analysis of the frequency of Finnish and Spanish WLs first digits to determine if their distribution is similar to the pattern documented by NBL. Deviations from the expected first digit frequency were analysed using Pearson's χ 2 , mean absolute deviation and Kuiper tests. Publicly available WL data from Finland and Spain, two countries with universal health insurance and National Health Systems but characterised by different levels of transparency and good governance standards. Adjustment of the observed distribution of the numbers reported in Finnish and Spanish WL data to the expected distribution according to NBL. WL data reported by the Finnish health system fits first digit NBL according to all statistical tests used (p=0.6519 in χ 2 test). For Spanish data, this hypothesis was rejected in all tests (p<0.0001 in χ 2 test). Testing deviations from NBL distribution can be a useful tool to identify problems with WL data trustworthiness and signalling the need for further testing. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.
Kilpela, Lisa Smith; Blomquist, Kerstin; Verzijl, Christina; Wilfred, Salomé; Beyl, Robbie; Becker, Carolyn Black
2017-01-01
Objective The Body Project is a cognitive dissonance-based body image improvement program with ample research support among female samples. More recently, researchers have highlighted the extent of male body dissatisfaction and disordered eating behaviors; however, boys/men have not been included in the majority of body image improvement programs. This study aims to explore the efficacy of a mixed-gender Body Project compared to the historically female-only body image intervention program. Method Participants included male and female college students (N=185) across two sites. We randomly assigned women to a mixed-gender modification of the two-session, peer-led Body Project (MG), the two-session, peer-led, female-only (FO) Body Project, or a waitlist control (WL), and men to either MG or WL. Participants completed self-report measures assessing negative affect, appearance-ideal internalization, body satisfaction, and eating disorder pathology at baseline, post-test, and at two- and six-month follow-up. Results We used linear mixed effects modeling to estimate the change from baseline over time for each dependent variable across conditions. For women, results were mixed regarding post-intervention improvement compared to WL, and were largely non-significant compared to WL at 6-month follow-up. Alternatively, results indicated that men in MG consistently improved compared to WL through 6-month follow-up on all measures except negative affect and appearance-ideal internalization. Discussion Results differed markedly between female and male samples, and were more promising for men than for women. Various explanations are provided, and further research is warranted prior to drawing firm conclusions regarding mixed-gender programming of the Body Project. PMID:27188688
Kamat, Ashish M; Cookson, Michael; Witjes, J Alfred; Stenzl, Arnulf; Grossman, H Barton
2016-04-27
Background: The International Bladder Cancer Group (IBCG) recently proposed a new definition of disease progression in non-muscle invasive bladder cancer (NMIBC), including change in T-stage, change to T2 or higher or change from low to high grade. Objective: To establish whether blue light cystoscopy with hexaminolevulinate (HAL) impacts the rate of progression and time to progression using the revised definition. Methods: An earlier long-term follow-up of a controlled Phase III study reported outcomes following blue light cystoscopy with HAL (255 patients) or white light (WL) cystoscopy (261 patients) in NMIBC patients. The data was re-analysed according to the new definition. Results: In the original analysis, after 4.5 years (median), eight HAL and 16 WL patients were deemed to have progressed (transition from NMIBC to muscle invasive bladder cancer, (T2-4)). According to the new definition, additional patients in both groups were found to have progressed: 31 (12.2%) HAL vs 46 (17.6%) WL ( p = 0.085) with four (1.6%) HAL and 11 (4.2%) WL patients progressing from Ta to CIS. Time to progression was longer in the HAL group ( p = 0.05). Conclusions: Applying the new IBCG definition there was a trend towards a lower rate of progression in HAL patients, particularly in those progressing from Ta to CIS. Time to progression was significantly prolonged. This suggests that patients should receive blue light cystoscopy with HAL rather than WL at resection. Adoption of the new definition could allow more patients at risk of progression to be treated appropriately earlier.
Khan, Anmar A; Mundra, Piyushkumar A; Straznicky, Nora E; Nestel, Paul J; Wong, Gerard; Tan, Ricardo; Huynh, Kevin; Ng, Theodore W; Mellett, Natalie A; Weir, Jacquelyn M; Barlow, Christopher K; Alshehry, Zahir H; Lambert, Gavin W; Kingwell, Bronwyn A; Meikle, Peter J
2018-02-01
High-density lipoprotein (HDL) lipid composition and function may better reflect cardiovascular risk than HDL cholesterol concentration. This study characterized the relationships between HDL composition, metabolism, and function in metabolic syndrome (MetS) patients and how changes in composition after weight loss (WL) and exercise treatments are related to function. Plasma samples from MetS patients (n=95) and healthy individuals (n=40) were used in this study. Subsets of the MetS group underwent 12 weeks of no treatment (n=17), WL (n=19), or WL plus exercise (WLEX; n=17). HDL was isolated using density-gradient ultracentrifugation. The HDL lipidome was analyzed by mass spectrometry, and particle size determined by nuclear magnetic resonance. Cholesteryl ester transfer protein activity and ex vivo HDL cholesterol efflux capacity (CEC) were assessed. The HDL lipidome in the MetS patients was substantially different from that in healthy individuals, mean particle size was smaller, and CEC was lower. Several HDL phospholipid and sphingolipid species were associated with HDL diameter and CEC. The HDL lipidome and particle size were modified toward the healthy individuals after WL and WLEX treatments, with greater effects observed in the latter group. Cholesteryl ester transfer protein activity was reduced after WL and WLEX, and CEC was improved after WLEX. WLEX treatment in MetS patients normalizes the HDL lipidome and particle size profile and enhances CEC. HDL lipids associated with diminished CEC may represent novel biomarkers for early prediction of HDL dysfunction and disease risk and may represent potential therapeutic targets for future HDL therapies. URL: http://www.clinicaltrials.gov. Unique identifier: NCT00163943. © 2017 American Heart Association, Inc.
Final Report - Management of High Sulfur HLW, VSL-13R2920-1, Rev. 0, dated 10/31/2013
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, Albert A.; Gan, H.; Pegg, I. L.
2013-11-13
The present report describes results from a series of small-scale crucible tests to determine the extent of corrosion associated with sulfur containing HLW glasses and to develop a glass composition for a sulfur-rich HLW waste stream, which was then subjected to small-scale melter testing to determine the maximum acceptable sulfate loadings. In the present work, a new glass formulation was developed and tested for a projected Hanford HLW composition with sulfate concentrations high enough to limit waste loading. Testing was then performed on the DM10 melter system at successively higher waste loadings to determine the maximum waste loading without themore » formation of a separate sulfate salt phase. Small scale corrosion testing was also conducted using the glass developed in the present work, the glass developed in the initial phase of this work [26], and a high iron composition, all at maximum sulfur concentrations determined from melter testing, in order to assess the extent of Inconel 690 and MA758 corrosion at elevated sulfate contents.« less
Crawford, Charles G.; Wilber, William G.; Peters, James G.
1980-01-01
A digital model calibrated to conditions in the Wabash River in Huntington County, Ind., was used to predict alternatives for future waste loadings that would be compatible with Indiana stream water-quality standards defined for two critical hydrologic conditons, summer and winter low flows. The major point-source waste load affecting the Wabash River in Huntington County is the Huntington wastewater-treatment facility. The most significnt factor potentially affecting the dissolved-oxygen concentration during summer low flows is nitrification. However, nitrification should not be a limiting factor on the allowable nitrogenous and carbonaceous waste loads for the Huntington wastewater-treatment facility during summer low flows if the ammonia-nitrogen toxicity standard for Indiana streams is met. The disolved-oxygen standard for Indiana stream, an average of 5.0 milligrams per liter, should be met during summer and winter low flows if the National Pollution Discharge Elimination System 's 5-day, carbonaceous biochemical-oxygen demands of a monthly average concentration of 30 milligrams per liter and a maximum weekly average of 45 milligrams per liter are not exceeded.
Ceramic Single Phase High-Level Nuclear Waste Forms: Hollandite, Perovskite, and Pyrochlore
NASA Astrophysics Data System (ADS)
Vetter, M.; Wang, J.
2017-12-01
The lack of viable options for the safe, reliable, and long-term storage of nuclear waste is one of the primary roadblocks of nuclear energy's sustainable future. The method being researched is the incorporation and immobilization of harmful radionuclides (Cs, Sr, Actinides, and Lanthanides) into the structure of glasses and ceramics. Borosilicate glasses are the main waste form that is accepted and used by today's nuclear industry, but they aren't the most efficient in terms of waste loading, and durability is still not fully understood. Synroc-phase ceramics (i.e. hollandite, perovskite, pyrochlore, zirconolite) have many attractive qualities that glass waste forms do not: high waste loading, moderate thermal expansion and conductivity, high chemical durability, and high radiation stability. The only downside to ceramics is that they are more complex to process than glass. New compositions can be discovered by using an Artificial Neural Network (ANN) to have more options to optimize the composition, loading for performance by analyzing the non-linear relationships between ionic radii, electronegativity, channel size, and a mineral's ability to incorporate radionuclides into its structure. Cesium can be incorporated into hollandite's A-site, while pyrochlore and perovskite can incorporate actinides and lanthanides into their A-site. The ANN is used to predict new compositions based on hollandite's channel size, as well as the A-O bond distances of pyrochlore and perovskite, and determine which ions can be incorporated. These new compositions will provide more options for more experiments to potentially improve chemical and thermodynamic properties, as well as increased waste loading capabilities.
New combinations for Pacific endemic species: Marquesan Poaceae, and Micronesian Myrtaceae.
Tornabene, Michael W; Wagner, Warren L
2013-01-01
As part of the preparation for a comprehensive online flora of Pacific oceanic islands, numerous taxonomic changes have been necessary, primarily due to a new wealth of global molecular phylogenetic studies on genera that include Pacific islands species. In order to compile an accurate checklist of the Pacific island flora with up-to-date taxonomies, we are moving several species to their currently accepted genera. Two Marquesan Pennisetum Rich. are transferred to Cenchrus L. with the new combinations Cenchrus articularis (Trin.) M. Tornabene & W.L. Wagner, and Cenchrus henryanus (F. Br.) M. Tornabene & W.L. Wagner. A key to Marquesas Cenchrus is also provided to differentiate the two species. Additionally, one species of Eugenia L. is transferred to Syzygium Gaertn. with the new combination Syzygium stelechanthoides (Kaneh.) M. Tornabene & W.L. Wagner in accord with the aforementioned studies.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kawazu, T., E-mail: KAWAZU.Takuya@nims.go.jp; Noda, T.; Sakuma, Y.
2016-04-15
We investigated the excitation power P dependence of photoluminescence (PL) spectra of GaSb type-II quantum dots (QDs) in GaAs grown by droplet epitaxy. We prepared two QD samples annealed at slightly different temperatures (380 {sup o}C and 400 {sup o}C) and carried out PL measurements. The 20 {sup o}C increase of the annealing temperature leads to (1) about 140 and 60 times stronger wetting layer (WL) luminescence at low and high P, (2) about 45% large energy shift of QD luminescence with P, and (3) the different P dependence of the PL intensity ratio between the QD and the WL. These differences ofmore » the PL characteristics are explained by the effects of the WL.« less
The inner-disk and stellar properties of the young stellar object WL 16
NASA Technical Reports Server (NTRS)
Carr, John S.; Tokunaga, Alan T.; Najita, Joan; Shu, Frank H.; Glassgold, Alfred E.
1993-01-01
We present kinematic evidence for a rapidly rotating circumstellar disk around the young stellar object WL 16, based on new high-velocity-resolution data of the v = 2-0 CO bandhead emission. A Keplerian disk provides an excellent fit to the observed profile and requires a projected velocity for the CO-emitting region of roughly 250 km/s at the inner radius and 140 km/s at the outer radius, giving a ratio of the inner to the outer radius of about 0.3. We show that satisfying the constraints imposed by the gas kinematics, the observed CO flux, and the total source luminosity requires the mass of WL 16 to lie between 1.4 and 2.5 solar mass. The inner disk radius for the CO emission must be less than 8 solar radii.
Portraits of Well-Being: Photography as a Mental Health Support for Women With HIV
Teti, Michelle; French, Bryana; Kabel, Allison; Farnan, Rose
2017-01-01
Many women living with HIV/AIDS (WL-HIV/AIDS) experience significant mental distress. Although creative arts strategies are well positioned to help support women by inspiring creativity and meaning-making, few arts programs have been implemented and evaluated with this population. We conducted a photography project with thirty WL-HIV/AIDS from three United States cities. Participants took pictures to capture their life with HIV/AIDS and described their photos and stories in group and individual sessions. Using thematic analysis, we identified that the project supported women’s mental health in four ways by facilitating empowerment and helping women to express themselves, address their mental health with new tools like photography, and process past traumas. Photography projects may help WL-HIV/AIDS understand and manage their mental health. PMID:29657558
N-SINK - reduction of waste water nitrogen load
NASA Astrophysics Data System (ADS)
Aalto, Sanni; Tiirola, Marja; Arvola, Lauri; Huotari, Jussi; Tulonen, Tiina; Rissanen, Antti; Nykänen, Hannu
2014-05-01
Protection of the Baltic Sea from eutrophication is one of the key topics in the European Union environmental policy. One of the main anthropogenic sources of nitrogen (N) loading into Baltic Sea are waste water treatment plants, which are currently capable in removing only 40-70% of N. European commission has obliged Finland and other Baltic states to reduce nitrate load, which would require high monetary investments on nitrate removal processes in treatment plants. In addition, forced denitrification in treatment plants would increase emissions of strong greenhouse gas N2O. In this project (LIFE12 FI/ENV/597 N-SINK) we will develop and demonstrate a novel economically feasible method for nitrogen removal using applied ecosystem services. As sediment is known to have enormous capacity to reduce nitrate to nitrogen gas through denitrification, we predict that spatial optimization of the waste water discharge would be an efficient way to reduce nitrate-based load in aquatic systems. A new sediment filtration approach, which will increase both the area and time that nitrified waste water will be in contact with the reducing microbes of the sediment, is tested. Compared to the currently implemented practice, where purified waste water is discharged though one-point outlet system, we expect that sediment filtration system will result in more efficient denitrification and decreased N load to aquatic system. We will conduct three full-scale demonstrations in the receiving water bodies of waste water treatment plants in Southern and Central Finland. The ecosystem effects of sediment filtration system will be monitored. Using the most advanced stable isotope techniques will allow us accurately measure denitrification and unfavoured DNRA (reduction of nitrite to ammonium) activity.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Buck, Edgar C.; Wittman, Richard S.
The U.S. Department of Energy Office of Nuclear Energy (DOE-NE), Office of Fuel Cycle Technology has established the Used Fuel Disposition Campaign (UFDC) to conduct the research and development activities related to storage, transportation, and disposal of used nuclear fuel (UNF) and high-level radioactive waste. Within the UFDC, the components for a general system model of the degradation and subsequent transport of UNF is being developed to analyze the performance of disposal options [Sassani et al., 2012]. Two model components of the near-field part of the problem are the ANL Mixed Potential Model and the PNNL Radiolysis Model. This reportmore » is in response to the desire to integrate the two models as outlined in [Buck, E.C, J.L. Jerden, W.L. Ebert, R.S. Wittman, (2013) “Coupling the Mixed Potential and Radiolysis Models for Used Fuel Degradation,” FCRD-UFD-2013-000290, M3FT-PN0806058]« less
Immobilization of Technetium in a Metallic Waste Form
DOE Office of Scientific and Technical Information (OSTI.GOV)
S.M. Frank; D. D. Keiser, Jr.; K. C. Marsden
Fission-product technetium accumulated during treatment of spent nuclear fuel will ultimately be disposed of in a geological repository. The exact form of Tc for disposal has yet to be determined; however, a reasonable solution is to incorporate elemental Tc into a metallic waste form similar to the waste form produced during the pyrochemical treatment of spent, sodium-bonded fuel. This metal waste form, produced at the Idaho National Laboratory, has undergone extensive qualification examination and testing for acceptance to the Yucca Mountain geological repository. It is from this extensive qualification effort that the behavior of Tc and other fission products inmore » the waste form has been elucidated, and that the metal waste form is extremely robust in the retention of fission products, such as Tc, in repository like conditions. This manuscript will describe the metal waste form, the behavior of Tc in the waste form; and current research aimed at determining the maximum possible loading of Tc into the metal waste and subsequent determination of the performance of high Tc loaded metal waste forms.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Gonsalves, C.; Xue, B.; Yepes, M.
1994-03-01
A single regeneration procedure using cotyledon examples effectively regenerated five commercially grown muskmelon cultivars. This regeneration scheme was used to facilitate gene transfers using either Agrobacterium tumefaciens or microprojectile bombardment methods. In both cases, the transferred genes were from the T-DNA region of the binary vector plasmid pGA482GG/cp cucumber mosaic virus-white leaf strain (CMV-WL), which contains genes that encode neomycin phosphotransferase II (NPT II), [beta]-glucuronidase (GUS), and the CMV-WL coat protein (CP). Explants treated with pGA482GG/cpCMV-WL regenerated shoots on Murashige and Skoog medium containing 4.4 [mu]m 6-benzylaminopurine (BA), kanamycin (Km) at 150 mg[center dot]liter[sup [minus]1] and carbenicillin (Cb) at 500more » mg[center dot]liter[sup [minus]1]. The authors' comparison of A. tumefaciens- and microprojectile-mediated gene transfer procedures shows that both methods effectively produce nearly the same percentage of transgenic plants. R[sub 0] plants were first tested for GUS or NPT II expression, then the polymerase chain reaction (PCR) and other tests were used to verify the transfer of the NPT II, GUS, and CMV-WL CP genes.« less
Effect of Adolescent Bariatric Surgery on the Brain and Cognition: A Pilot Study.
Pearce, Alaina L; Mackey, Eleanor; Cherry, J Bradley C; Olson, Alexandra; You, Xiaozhen; Magge, Sheela N; Mietus-Snyder, Michele; Nadler, Evan P; Vaidya, Chandan J
2017-11-01
Neurocognitive deficits in pediatric obesity relate to poor developmental outcomes. We sought preliminary evidence for changes in brain and cognitive functioning relevant to obesogenic behavior following vertical sleeve gastrectomy (VSG) in adolescents relative to wait-listed (WL) and healthy controls (HC). Thirty-six adolescents underwent fMRI twice 4 months apart, during executive, reward, and episodic memory encoding, in addition to behavioral testing for reward-related decision making. VSG adolescents lost weight, while WL gained weight and HC did not change between time points. Gains in executive and reward-related performance were larger in VSG than control groups. Group × Time interaction (P < 0.05 corrected) in left prefrontal cortex during N-back showed greater presurgical activation and postsurgical reduction comparable to HC levels but increased in WL between time points. Similarly, left striatal parametric response to reward value reduced after surgery to HC levels; WL did not change. Memory-related medial temporal activation did not change in any group. Results provide pilot evidence for functional brain changes induced by VSG in adolescents with severe obesity. Weight loss and gain were paralleled by reduced and increased prefrontal activation, respectively, suggesting neural plasticity related to metabolic change. © 2017 The Obesity Society.
Duality of Weak and Strong Scatterer in Luttinger Liquid Coupled to Massless Bosons
NASA Astrophysics Data System (ADS)
Galda, Alexey; Yurkevich, Igor; Yevtushenko, Oleg; Lerner, Igor
2013-03-01
We study electronic transport in a Luttinger liquid (LL) with an embedded impurity, which is either a weak scatterer (WS) or a weak link (WL), when interacting electrons are coupled to one-dimensional massless bosons (e.g., acoustic phonons). The additional coupling competes with Coulomb interaction changing scaling exponents of various correlation functions. The impurity strength λ and the tunneling amplitude t in the WS and WL limits scale at low energies ɛ as: λ (ɛ) ~λ0ɛ Δws - 1 and t (ɛ) ~t0ɛ Δwl - 1 , correspondingly. We find that the duality relation between the scaling dimensions established for the standard LL, ΔwsΔwl = 1 , holds in the presence of the additional coupling for an arbitrary fixed strength of boson scattering from the impurity. As a result, at low temperatures the system remains either an ideal insulator or an ideal metal, regardless of the scattering strength. However, in the case when electron and boson scattering from the impurity are correlated, the system has a rich phase diagram that includes a metal-insulator transition at some intermediate values of the scattering. Leverhulme grant RPG-380, DFG through SFB TR-12, DoE Office of Science under the Contract No. DEAC02-06CH11357
Hyun, Dong-Wook; Shin, Na-Ri; Kim, Min-Soo; Kim, Pil Soo; Kim, Joon Yong; Whon, Tae Woong; Bae, Jin-Woo
2014-02-01
A novel, Gram-staining-positive, facultatively anaerobic, non-motile and coccus-shaped bacterium, strain WL80(T), was isolated from the gut of an abalone, Haliotis discus hannai, collected from the northern coast of Jeju in Korea. Optimal growth occurred at 30 °C, pH 7-8 and with 1% (w/v) NaCl. Phylogenetic analyses based on the 16S rRNA gene sequence revealed that strain WL80(T) fell within the cluster of the genus Actinomyces, with highest sequence similarity to the type strains of Actinomyces radicidentis (98.8% similarity) and Actinomyces urogenitalis (97.0% similarity). The major cellular fatty acids were C18 : 1ω9c and C16 : 0. Menaquinone-10 (H4) was the major respiratory quinone. The genomic DNA G+C content of the isolate was 70.4 mol%. DNA-DNA hybridization values with closely related strains indicated less than 7.6% genomic relatedness. The results of physiological, biochemical, chemotaxonomic and genotypic analyses indicated that strain WL80(T) represents a novel species of the genus Actinomyces, for which the name Actinomyces haliotis sp. nov. is proposed. The type strain is WL80(T) ( = KACC 17211(T) = JCM 18848(T)).
Valdez, Marcos B; Kinoshita, Keiji; Mizutani, Makoto; Fujiwara, Akira; Yazawa, Hajime; Yamagata, Takahiro; Shimada, Kiyoshi; Namikawa, Takao
2009-04-01
Histocompatibility was assessed in the RIR-Y8/NU, BL-E, YL, and WL-G chicken closed colonies by hemagglutination test using anti-red blood cell (RBC) antibodies (HT), skin transplantation test (STT), and formation of isohemagglutinins (FIHs) during STT. The YL individuals all showed the survival of skingrafts for more than 17 days with no FIHs in STT and no RBC antigenic variations in HT, indicating a histocompatible nature together with high homogeneity at serological loci. The BL-E as well as WL-G closed colonies were also found to be histocompatible in the STT with no FIHs, although the HT showed heterogeneities at serological locus/loci other than the B and C blood group loci which have significant effects on histocompatibility or FIHs in chicken. In the RIR-Y8/NU closed colonies, one individual in 6 reciprocal combinations of the STT showed early skingraft rejection with positive FIHs caused by different B locus alleles, and the HT suggested relatively high heterogeneities at the other serological loci too. The closed colonies of YL, BL-E, and WL-G will be useful avian materials for transplantation or related experiments, but RIR-Y8/NU needs further pedigree selection for serological homogeneity.
Uitdehaag, K A; Rodenburg, T B; van Hierden, Y M; Bolhuis, J E; Toscano, M J; Nicol, C J; Komen, J
2008-09-01
Birds from Rhode Island Red (RIR) origin show a lower fear response and less feather pecking than birds from White Leghorn (WL) origin. This study investigated whether responses in fear eliciting tests were affected if RIR and WL birds were housed together. Experimental groups contained either birds from one line only ('pure' groups) or an equal number of RIR and WL birds ('mixed' groups). These arrangements were maintained from hatch onwards, throughout the rearing and laying period. Birds were subjected to open field tests at 5-6 weeks and 17-18 weeks of age and to manual restraint tests at 7-8 weeks and 24 weeks of age. RIR birds were more active in both open field tests and in the manual restraint test at 24 weeks of age as compared with WL birds. RIR birds from pure groups were more active in the open field test at 17-18 weeks and in the manual restraint test at 24 weeks of age than RIR birds from mixed groups. These results suggest that otherwise low fearful RIR birds may adopt a higher fear response if they are housed together with more fearful conspecifics. These effects do not emerge until after 8 weeks of age.
NASA Astrophysics Data System (ADS)
Santamaria-Aguilar, S.; Arns, A.; Vafeidis, A. T.
2017-04-01
Both the temporal and spatial variability of storm surge water level (WL) curves are usually not taken into account in flood risk assessments as observational data are often scarce. In addition, sea-level rise (SLR) can further affect the variability of WLs. We analyze the temporal and spatial variability of the WL curve of 75 historical storm surge events that have been numerically simulated for St. Peter-Ording at the German North Sea coast, considering the effects induced by three SLR scenarios (RCP 4.5, RCP 8.5, and a RCP 8.5 high end scenario). We assess potential impacts of these scenarios on two parameters related to flooding: overflow volumes and fullness. Our results indicate that due to both the temporal and spatial variability of those events the resulting overflow volume can be two or even three times greater. We observe a steepening of the WL curve with an increase of the tidal range under the three SLR scenarios, although SLR induced effects are relatively higher for the RCP 4.5. The steepening of the WL curve with SLR produces a reduction of the fullness, but the changes in overflow volumes also depend on the magnitude of the storm surge event.
Wilber, William G.; Crawford, Charles G.; Peters, James G.
1979-01-01
A digital model calibrated to conditions in Sand Creek near Greensburg, Ind., was used to develop alternatives for future waste loadings that would be compatible with Indiana stream water-quality standards defined for two critical hydrologic conditions, summer and winter low flows. The only point-source waste load affecting Sand Creek in the vicinity of Greensburg is the Greensburg wastewater-treatment facility. Non-point, unrecorded waste loads seemed to be significant during three water-quality surveys done by the Indiana State Board of Health. Natural streamflow in Sand Creek during the summer and annual 7-day, 10-year low flow is zero so no benefit from dilution is provided. Effluent ammonia-nitrogen concentrations from the Greensburg wastewater-treatment facility will not meet Indiana water-quality standards during summer and winter low flows. To meet the water-quality standard the wastewater-effluent would be limited to a maximum total ammonia-nitrogen concentration of 2.5 mg/l for summer months (June through August) and 4.0 mg/l for winter months (November through March). Model simulations indicate that benthic-oxygen demand, nitrification, and the dissolved-oxygen concentration of the wastewater effluent are the most significant factors affecting the in-stream dissolved-oxygen concentration during summer low flows. The model predicts that with a benthic-oxygen demand of 1.5 grams per square meter per day at 20C the stream has no additional waste-load assimilative capacity. Present carbonaceous biochemical-oxygen demand loads from the Greensburg wastewater-treatment facility will not result in violations of the in-stream dissolved-oxygen standard (5 mg/l) during winter low flows. (Kosco-USGS)
Soltani, Maryam; Kerachian, Reza
2018-04-15
In this paper, a new methodology is proposed for the real-time trading of water withdrawal and waste load discharge permits in agricultural areas along the rivers. Total Dissolved Solids (TDS) is chosen as an indicator of river water quality and the TDS load that agricultural water users discharge to the river are controlled by storing a part of return flows in some evaporation ponds. Available surface water withdrawal and waste load discharge permits are determined using a non-linear multi-objective optimization model. Total available permits are then fairly reallocated among agricultural water users, proportional to their arable lands. Water users can trade their water withdrawal and waste load discharge permits simultaneously, in a bilateral, step by step framework, which takes advantage of differences in their water use efficiencies and agricultural return flow rates. A trade that would take place at each time step results in either more benefit or less diverted return flow. The Nucleolus cooperative game is used to redistribute the benefits generated through trades in different time steps. The proposed methodology is applied to PayePol region in the Karkheh River catchment, southwest Iran. Predicting that 1922.7 Million Cubic Meters (MCM) of annual flow is available to agricultural lands at the beginning of the cultivation year, the real-time optimization model estimates the total annual benefit to reach 46.07 million US Dollars (USD), which requires 6.31 MCM of return flow to be diverted to the evaporation ponds. Fair reallocation of the permits, changes these values to 35.38 million USD and 13.69 MCM, respectively. Results illustrate the effectiveness of the proposed methodology in the real-time water and waste load allocation and simultaneous trading of permits. Copyright © 2018 Elsevier Ltd. All rights reserved.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Reigel, M.; Johnson, F.; Crawford, C.
2011-09-20
The U.S. Department of Energy (DOE), Office of River Protection (ORP), is responsible for the remediation and stabilization of the Hanford Site tank farms, including 53 million gallons of highly radioactive mixed wasted waste contained in 177 underground tanks. The plan calls for all waste retrieved from the tanks to be transferred to the Waste Treatment Plant (WTP). The WTP will consist of three primary facilities including pretreatment facilities for Low Activity Waste (LAW) to remove aluminum, chromium and other solids and radioisotopes that are undesirable in the High Level Waste (HLW) stream. Removal of aluminum from HLW sludge canmore » be accomplished through continuous sludge leaching of the aluminum from the HLW sludge as sodium aluminate; however, this process will introduce a significant amount of sodium hydroxide into the waste stream and consequently will increase the volume of waste to be dispositioned. A sodium recovery process is needed to remove the sodium hydroxide and recycle it back to the aluminum dissolution process. The resulting LAW waste stream has a high concentration of aluminum and sodium and will require alternative immobilization methods. Five waste forms were evaluated for immobilization of LAW at Hanford after the sodium recovery process. The waste forms considered for these two waste streams include low temperature processes (Saltstone/Cast stone and geopolymers), intermediate temperature processes (steam reforming and phosphate glasses) and high temperature processes (vitrification). These immobilization methods and the waste forms produced were evaluated for (1) compliance with the Performance Assessment (PA) requirements for disposal at the IDF, (2) waste form volume (waste loading), and (3) compatibility with the tank farms and systems. The iron phosphate glasses tested using the product consistency test had normalized release rates lower than the waste form requirements although the CCC glasses had higher release rates than the quenched glasses. However, the waste form failed to meet the vapor hydration test criteria listed in the WTP contract. In addition, the waste loading in the phosphate glasses were not as high as other candidate waste forms. Vitrification of HLW waste as borosilicate glass is a proven process; however the HLW and LAW streams at Hanford can vary significantly from waste currently being immobilized. The ccc glasses show lower release rates for B and Na than the quenched glasses and all glasses meet the acceptance criterion of < 4 g/L. Glass samples spiked with Re{sub 2}O{sub 7} also passed the PCT test. However, further vapor hydration testing must be performed since all the samples cracked and the test could not be performed. The waste loading of the iron phosphate and borosilicate glasses are approximately 20 and 25% respectively. The steam reforming process produced the predicted waste form for both the high and low aluminate waste streams. The predicted waste loadings for the monolithic samples is approximately 39%, which is higher than the glass waste forms; however, at the time of this report, no monolithic samples were made and therefore compliance with the PA cannot be determined. The waste loading in the geopolymer is approximately 40% but can vary with the sodium hydroxide content in the waste stream. Initial geopolymer mixes revealed compressive strengths that are greater than 500 psi for the low aluminate mixes and less than 500 psi for the high aluminate mixes. Further work testing needs to be performed to formulate a geopolymer waste form made using a high aluminate salt solution. A cementitious waste form has the advantage that the process is performed at ambient conditions and is a proven process currently in use for LAW disposal. The Saltstone/Cast Stone formulated using low and high aluminate salt solutions retained at least 97% of the Re that was added to the mix as a dopant. While this data is promising, additional leaching testing must be performed to show compliance with the PA. Compressive strength tests must also be performed on the Cast Stone monoliths to verify PA compliance. Based on testing performed for this report, the borosilicate glass and Cast Stone are the recommended waste forms for further testing. Both are proven technologies for radioactive waste disposal and the initial testing using simulated Hanford LAW waste shows compliance with the PA. Both are resistant to leaching and have greater than 25% waste loading.« less
Waste Heat Approximation for Understanding Dynamic Compression in Nature and Experiments
NASA Astrophysics Data System (ADS)
Jeanloz, R.
2015-12-01
Energy dissipated during dynamic compression quantifies the residual heat left in a planet due to impact and accretion, as well as the deviation of a loading path from an ideal isentrope. Waste heat ignores the difference between the pressure-volume isentrope and Hugoniot in approximating the dissipated energy as the area between the Rayleigh line and Hugoniot (assumed given by a linear dependence of shock velocity on particle velocity). Strength and phase transformations are ignored: justifiably, when considering sufficiently high dynamic pressures and reversible transformations. Waste heat mis-estimates the dissipated energy by less than 10-20 percent for volume compressions under 30-60 percent. Specific waste heat (energy per mass) reaches 0.2-0.3 c02 at impact velocities 2-4 times the zero-pressure bulk sound velocity (c0), its maximum possible value being 0.5 c02. As larger impact velocities are implied for typical orbital velocities of Earth-like planets, and c02 ≈ 2-30 MJ/kg for rock, the specific waste heat due to accretion corresponds to temperature rises of about 3-15 x 103 K for rock: melting accompanies accretion even with only 20-30 percent waste heat retained. Impact sterilization is similarly quantified in terms of waste heat relative to the energy required to vaporize H2O (impact velocity of 7-8 km/s, or 4.5-5 c0, is sufficient). Waste heat also clarifies the relationship between shock, multi-shock and ramp loading experiments, as well as the effect of (static) pre-compression. Breaking a shock into 2 steps significantly reduces the dissipated energy, with minimum waste heat achieved for two equal volume compressions in succession. Breaking a shock into as few as 4 steps reduces the waste heat to within a few percent of zero, documenting how multi-shock loading approaches an isentrope. Pre-compression, being less dissipative than an initial shock to the same strain, further reduces waste heat. Multi-shock (i.e., high strain-rate) loading of pre-compressed samples may thus offer the closest approach to an isentrope, and therefore the most extreme compression at which matter can be studied at the "warm" temperatures of planetary interiors.
40 CFR 406.16 - Pretreatment standards for new sources.
Code of Federal Regulations, 2014 CFR
2014-07-01
... GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Corn Wet Milling Subcategory § 406.16 Pretreatment... new corn wet milling source to be discharged to the POTW (gallons per one hour for flow and pounds per day for BOD5 and TSS). Q = average existing waste load to POTW. R = average waste load for the new...
40 CFR 406.16 - Pretreatment standards for new sources.
Code of Federal Regulations, 2012 CFR
2012-07-01
... GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Corn Wet Milling Subcategory § 406.16 Pretreatment... new corn wet milling source to be discharged to the POTW (gallons per one hour for flow and pounds per day for BOD5 and TSS). Q = average existing waste load to POTW. R = average waste load for the new...
40 CFR 406.16 - Pretreatment standards for new sources.
Code of Federal Regulations, 2013 CFR
2013-07-01
... GUIDELINES AND STANDARDS GRAIN MILLS POINT SOURCE CATEGORY Corn Wet Milling Subcategory § 406.16 Pretreatment... new corn wet milling source to be discharged to the POTW (gallons per one hour for flow and pounds per day for BOD5 and TSS). Q = average existing waste load to POTW. R = average waste load for the new...
THE IMPACT OF THE MCU LIFE EXTENSION SOLVENT ON DWPF GLASS FORMULATION EFFORTS
DOE Office of Scientific and Technical Information (OSTI.GOV)
Peeler, D; Edwards, T
2011-03-24
As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NG-CSSX), a new strip acid, and modified monosodium titanate (mMST) will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing with the next generation solvent and mMST is required to determine the impact of these changes in 512-S operations as well as Chemical Process Cell (CPC), Defense Waste Processing Facility (DWPF) glass formulation activities, and melter operations at DWPF. To support programmatic objectives,more » the downstream impacts of the boric acid strip effluent (SE) to the glass formulation activities and melter operations are considered in this study. More specifically, the impacts of boric acid additions to the projected SB7b operating windows, potential impacts to frit production temperatures, and the potential impact of boron volatility are evaluated. Although various boric acid molarities have been reported and discussed, the baseline flowsheet used to support this assessment was 0.01M boric acid. The results of the paper study assessment indicate that Frit 418 and Frit 418-7D are robust to the implementation of the 0.01M boric acid SE into the SB7b flowsheet (sludge-only or ARP-added). More specifically, the projected operating windows for the nominal SB7b projections remain essentially constant (i.e., 25-43 or 25-44% waste loading (WL)) regardless of the flowsheet options (sludge-only, ARP added, and/or the presence of the new SE). These results indicate that even if SE is not transferred to the Sludge Receipt and Adjustment Tank (SRAT), there would be no need to add boric acid (from a trim tank) to compositionally compensate for the absence of the boric acid SE in either a sludge-only or ARP-added SB7b flowsheet. With respect to boron volatility, the Measurement Acceptability Region (MAR) assessments also suggest that Slurry Mix Evaporator (SME) acceptability decisions would not be different assuming either 100% of the B{sub 2}O{sub 3} from the SE were retained or volatilized. More specifically, the 0.84 wt% B{sub 2}O{sub 3} in the SE is so minor that its presence in the SME analysis does not influence SME acceptability decisions. In fact, using the 100% retention and 100% volatilization composition projections, only minor differences in the predicted properties of the glass product occur with all of the glasses being acceptable over a WL interval of 32-42%. Based on the 0.01M boric acid flowsheet, there is very little difference between Frit 418 and Frit 418-7D (a frit that was compositionally altered to account for the 0.84 wt% B{sub 2}O{sub 3} in the SE) with respect to melt temperature. In fact, when one evaluates the composition of Frit 418-7D, it lies within the current Frit 418 vendor specifications and therefore could have been produced by the vendor targeting the nominal composition of Frit 418.« less
Federal Register 2010, 2011, 2012, 2013, 2014
2013-04-03
... July 18, 1997 (62 FR 38652), EPA promulgated a new annual PM 2.5 NAAQS and on October 17, 2006 (71 FR..., the U.S. Court of Appeals for the District of Columbia, in Sierra Club v. EPA, No. 10- 1413, 2013 WL... Appeals, in Natural Resources Defense Council v. EPA, No. 08-1250, 2013 WL 45653 (D.C. Cir., filed July 15...
Hamid Khan, M A; Chowdhury, M S
2003-10-01
Beach Sand Exploitation Centre at Cox's Bazar, Bangladesh, produces commercial grade concentrations of magnetite, ilmenite, zircon, etc., from the high-grade accumulations available along the beach and foredune of Cox's Bazar. Solid state nuclear track detectors (CR-39 foils) were used to determine indoor radon concentration of radioactive mineral sands and the technologically enhanced radiation level inside the pilot plant of the Centre. It is found that the concentrations at processed mineral stock areas are high, and the maximum concentration was found to be 2,103 +/- 331 Bq m(-3) (0.23 +/- 0.03 WL). The indoor concentration of radon and its decay products in the raw sand stock area and at other locations was in the range of 116 +/- 27 Bq m(-3) (0.03 +/- 0.003 WL) to 2,042 +/- 233 Bq m(-3) (0.22 +/- 0.03 WL).
The lambda mechanism of the 0nbb-decay
NASA Astrophysics Data System (ADS)
Šimkovic, Fedor; Štefánik, Dušan; Dvornický, Rastislav
2017-11-01
The lambda mechanism (WL-WR exchange) of the neutrinoless double beta decay (0nbb-decay), which has origin in left-right symmetric model with right-handed gauge boson at TeV scale, is investigated. The revisited formalism of the 0nbb-decay, which includes higher order terms of nucleon current, is exploited. The corresponding nuclear matrix elements are calculated within quasiparticle random phase approximation with partial restoration of the isospin symmetry for nuclei of experimental interest. A possibility to distinguish between the conventional light neutrino mass (WL-WL exchange) and lambda mechanisms by observation of the 0nbb-decay in several nuclei is discussed. A qualitative comparison of effective lepton number violating couplings associated with these two mechanisms is performed. By making viable assumption about the seesaw type mixing of light and heavy neutrinos it is concluded that there is a dominance of the conventional light neutrino mass mechanism in the decay rate.
New combinations for Pacific endemic species: Marquesan Poaceae, and Micronesian Myrtaceae
Tornabene, Michael W.; Wagner, Warren L.
2013-01-01
Abstract As part of the preparation for a comprehensive online flora of Pacific oceanic islands, numerous taxonomic changes have been necessary, primarily due to a new wealth of global molecular phylogenetic studies on genera that include Pacific islands species. In order to compile an accurate checklist of the Pacific island flora with up-to-date taxonomies, we are moving several species to their currently accepted genera. Two Marquesan Pennisetum Rich. are transferred to Cenchrus L. with the new combinations Cenchrus articularis (Trin.) M. Tornabene & W.L. Wagner, and Cenchrus henryanus (F. Br.) M. Tornabene & W.L. Wagner. A key to Marquesas Cenchrus is also provided to differentiate the two species. Additionally, one species of Eugenia L. is transferred to Syzygium Gaertn. with the new combination Syzygium stelechanthoides (Kaneh.) M. Tornabene & W.L. Wagner in accord with the aforementioned studies. PMID:24399889
Lu, Xinyao; Wang, Yuqin; Zong, Hong; Ji, Hao; Zhuge, Bin; Dong, Zhuoli
2016-01-01
ABSTRACT 2-Phenylethanol (2-PE) is a high value aromatic alcohol with a rose-like odor that is utilized in the cosmetics and other industries. Although the chemical routes of 2-PE production have been altered by some microbial transformation processes, the poor tolerance to organic solvents of these microorganisms has limited the 2-PE yield. In this study, the stress-tolerant yeast Candida glycerinogenes WL2002-5 showed a 2-PE tolerance to 4 g/l, which is the highest reported to date. Moreover, the 2-PE titer in a batch fermentation from L-phenylalanine reached 5g/l, which is the highest level achieved by fermentation without in situ product recovery. These results suggest C. glycerinogenes WL2002-5 is a robust strain for the bioproduction of 2-PE with potential for commercial exploitation. PMID:27435817
Lu, Xinyao; Wang, Yuqin; Zong, Hong; Ji, Hao; Zhuge, Bin; Dong, Zhuoli
2016-11-01
2-Phenylethanol (2-PE) is a high value aromatic alcohol with a rose-like odor that is utilized in the cosmetics and other industries. Although the chemical routes of 2-PE production have been altered by some microbial transformation processes, the poor tolerance to organic solvents of these microorganisms has limited the 2-PE yield. In this study, the stress-tolerant yeast Candida glycerinogenes WL2002-5 showed a 2-PE tolerance to 4 g/l, which is the highest reported to date. Moreover, the 2-PE titer in a batch fermentation from L-phenylalanine reached 5g/l, which is the highest level achieved by fermentation without in situ product recovery. These results suggest C. glycerinogenes WL2002-5 is a robust strain for the bioproduction of 2-PE with potential for commercial exploitation.
García-Escalera, Julia; Valiente, Rosa M; Chorot, Paloma; Ehrenreich-May, Jill; Kennedy, Sarah M; Sandín, Bonifacio
2017-08-21
Anxiety and depression are common, impairing conditions that evidence high comorbidity rates in adolescence. The Unified Protocol for Transdiagnostic Treatment of Emotional Disorders in Adolescents (UP-A) is one of the few existing resources aimed at applying transdiagnostic treatment principles to target core dysfunctions associated with both anxiety and depression within a single protocol. To our knowledge, this is the first study examining the efficacy of the UP-A adapted as a universal preventive intervention program. The primary aim of this study is to examine whether the Spanish version of the UP-A is more effective than a waitlist (WL) control group in reducing and preventing symptoms of anxiety and depression when employed as a universal, classroom-based preventive intervention. The secondary aim is to investigate changes in a broad range of secondary outcome measures, including negative and positive affect, anxiety sensitivity, emotional avoidance, top problems ratings, school grades, depression and anxiety-related interference, self-esteem, life satisfaction, quality of life, conduct problems, hyperactivity/inattention symptoms, peer problems, prosocial behavior, school adjustment, and discipline problems. Other aims are to assess a range of possible predictors of intervention effects and to examine the feasibility and the acceptability of implementing UP-A in a prevention group format and in a school setting. A cluster, randomized, WL, controlled trial design with classroom as the unit of randomization was used in this study. Five classes including a total of 152 adolescents were randomized to the experimental or WL control groups. Participants in the experimental group received 9 55-minute sessions delivered by advanced doctoral and masters students in clinical psychology. The WL control group will receive the intervention once the 3-month follow-up assessment is completed. We have recruited participants to the cluster randomized controlled trial (RCT) and have conducted the intervention with the experimental group. We expect the WL control group to complete the intervention in July 2017. Data analysis will take place during the second semester of 2017. We expect the experimental group to outperform the WL control group at post-intervention and 3-month follow-up. We also expect the WL control group to show improvements in primary and secondary outcome measures after receiving the intervention. Results will have implications for researchers, families, and education providers. Clinicaltrials.gov NCT03123991; https://clinicaltrials.gov/ct2/show/NCT03123991 (Archived by WebCite at http://www.webcitation.org/6qp7GIzcR). ©Julia García-Escalera, Rosa M Valiente, Paloma Chorot, Jill Ehrenreich-May, Sarah M Kennedy, Bonifacio Sandín. Originally published in JMIR Research Protocols (http://www.researchprotocols.org), 21.08.2017.
Polyp detection rates using magnification with narrow band imaging and white light.
Gilani, Nooman; Stipho, Sally; Panetta, James D; Petre, Sorin; Young, Michele A; Ramirez, Francisco C
2015-05-16
To compare the yield of adenomas between narrow band imaging and white light when using high definition/magnification. This prospective, non-randomized comparative study was performed at the endoscopy unit of veteran affairs medical center in Phoenix, Arizona. Consecutive patients undergoing first average risk colorectal cancer screening colonoscopy were selected. Two experienced gastroenterologists performed all the procedures that were blinded to each other's findings. Demographic details were recorded. Data are presented as mean ± SEM. Proportional data were compared using the χ(2) test and means were compared using the Student's t test. Tandem colonoscopy was performed in a sequential and segmental fashion using one of 3 strategies: white light followed by narrow band imaging [Group A: white light (WL) → narrow band imaging (NBI)]; narrow band imaging followed by white light (Group B: NBI → WL) and, white light followed by white light (Group C: WL → WL). Detection rate of missed polyps and adenomas were evaluated in all three groups. Three hundred patients were studied (100 in each Group). Although the total time for the colonoscopy was similar in the 3 groups (23.8 ± 0.7, 22.2 ± 0.5 and 24.1 ± 0.7 min for Groups A, B and C, respectively), it reached statistical significance between Groups B and C (P < 0.05). The cecal intubation time in Groups B and C was longer than for Group A (6.5 ± 0.4 min and 6.5 ± 0.4 min vs 4.9 ± 0.3 min; P < 0.05). The withdrawal time for Groups A and C was longer than Group B (18.9 ± 0.7 min and 17.6 ± 0.6 min vs 15.7 ± 0.4 min; P < 0.05). Overall miss rate for polyps and adenomas detected in three groups during the second look was 18% and 17%, respectively (P = NS). Detection rate for polyps and adenomas after first look with white light was similar irrespective of the light used during the second look (WL → WL: 13.7% for polyps, 12.6% for adenomas; WL → NBI: 14.2% for polyps, 11.3% for adenomas). Miss rate of polyps and adenomas however was significantly higher when NBI was used first (29.3% and 30.3%, respectively; P < 0.05). Most missed adenomas were ≤ 5 mm in size. There was only one advanced neoplasia (defined by size only) missed during the first look. Our data suggest that the tandem nature of the procedure rather than the optical techniques was associated with the detection of additional polyps' and adenomas.
Polyp detection rates using magnification with narrow band imaging and white light
Gilani, Nooman; Stipho, Sally; Panetta, James D; Petre, Sorin; Young, Michele A; Ramirez, Francisco C
2015-01-01
AIM: To compare the yield of adenomas between narrow band imaging and white light when using high definition/magnification. METHODS: This prospective, non-randomized comparative study was performed at the endoscopy unit of veteran affairs medical center in Phoenix, Arizona. Consecutive patients undergoing first average risk colorectal cancer screening colonoscopy were selected. Two experienced gastroenterologists performed all the procedures that were blinded to each other’s findings. Demographic details were recorded. Data are presented as mean ± SEM. Proportional data were compared using the χ2 test and means were compared using the Student’s t test. Tandem colonoscopy was performed in a sequential and segmental fashion using one of 3 strategies: white light followed by narrow band imaging [Group A: white light (WL) → narrow band imaging (NBI)]; narrow band imaging followed by white light (Group B: NBI → WL) and, white light followed by white light (Group C: WL → WL). Detection rate of missed polyps and adenomas were evaluated in all three groups. RESULTS: Three hundred patients were studied (100 in each Group). Although the total time for the colonoscopy was similar in the 3 groups (23.8 ± 0.7, 22.2 ± 0.5 and 24.1 ± 0.7 min for Groups A, B and C, respectively), it reached statistical significance between Groups B and C (P < 0.05). The cecal intubation time in Groups B and C was longer than for Group A (6.5 ± 0.4 min and 6.5 ± 0.4 min vs 4.9 ± 0.3 min; P < 0.05). The withdrawal time for Groups A and C was longer than Group B (18.9 ± 0.7 min and 17.6 ± 0.6 min vs 15.7 ± 0.4 min; P < 0.05). Overall miss rate for polyps and adenomas detected in three groups during the second look was 18% and 17%, respectively (P = NS). Detection rate for polyps and adenomas after first look with white light was similar irrespective of the light used during the second look (WL → WL: 13.7% for polyps, 12.6% for adenomas; WL → NBI: 14.2% for polyps, 11.3% for adenomas). Miss rate of polyps and adenomas however was significantly higher when NBI was used first (29.3% and 30.3%, respectively; P < 0.05). Most missed adenomas were ≤ 5 mm in size. There was only one advanced neoplasia (defined by size only) missed during the first look. CONCLUSION: Our data suggest that the tandem nature of the procedure rather than the optical techniques was associated with the detection of additional polyps’ and adenomas. PMID:25992195
Bovine myofiber characteristics are influenced by postweaning nutrition.
Greenwood, P L; Tomkins, N W; Hunter, R A; Allingham, P G; Harden, S; Harper, G S
2009-10-01
This study determined the extent to which bovine longissimus lumborum muscle (LLM) myofibers are influenced by nutrition for 120 d from weaning and the time-course of recovery after severe postweaning nutritional restriction. After weaning, 3 groups of Belmont Red cattle, a tropically adapted breed, were fed to achieve rapid growth (RG, > or =0.6 kg of BW gain/d; n = 16), slow growth (SG, 0.2 kg of BW gain/d; n = 17), or BW loss (WL, 10% loss of weaning weight; n = 17) over 120 d. They were then grazed as 1 group at pasture with forage supplementation for 600 d until slaughter at approximately 500 kg of BW. Samples of LLM were taken from 8 to 12 animals per treatment 6 d before (baseline) and 115, 204, 324, and 476 d after commencement of the study and from all cattle at slaughter (d 721). Myofiber characteristics were determined by immunocytochemical staining of myosin heavy chains. Cross-sectional areas (CSA) of the major myofiber types 1, 2A, and 2X in WL were reduced at d 115 compared with baseline and with the growth groups (all P < 0.001); however, there was little difference in the percentage of the different myofiber types (all P > 0.10). Differences in CSA of the major myofiber types between WL and the growth groups at 115 d were smallest for type 1 (slow oxidative) and greatest for type 2X (fast glycolytic). Consequently, the relative area (percentage of total myofiber area) of type 1 myofibers in WL was significantly greater at 115 d than in the growth groups (P < 0.001). During recovery from postweaning nutritional restriction, significant differences in major myofiber type percentages were not evident (all P > 0.10), and by 721 d CSA of myofiber types differed little between the treatment groups, although SG had greater CSA of type 1 (P < 0.05) and type 2A (P < 0.01) myofibers than WL and RG. At 721 d, the relative area of type 2A myofibers was less in WL compared with SG (P < 0.01) and RG (P < 0.05) and of type 2X myofibers greater (P < 0.05) in WL compared with SG. It is concluded that in the LLM of cattle undergoing severe nutritional restriction immediately postweaning, the size of the more glycolytic fiber types is more adversely affected than the more oxidative types, resulting in an increased relative area of type 1, slow oxidative myofibers. However, given adequate time and nutriment at pasture, LLM myofiber characteristics of cattle recovered to near normal after severe, chronic nutritional restriction immediately postweaning, consistent with earlier findings for beef quality.
García-Escalera, Julia; Valiente, Rosa M; Ehrenreich-May, Jill; Kennedy, Sarah M; Sandín, Bonifacio
2017-01-01
Background Anxiety and depression are common, impairing conditions that evidence high comorbidity rates in adolescence. The Unified Protocol for Transdiagnostic Treatment of Emotional Disorders in Adolescents (UP-A) is one of the few existing resources aimed at applying transdiagnostic treatment principles to target core dysfunctions associated with both anxiety and depression within a single protocol. To our knowledge, this is the first study examining the efficacy of the UP-A adapted as a universal preventive intervention program. Objective The primary aim of this study is to examine whether the Spanish version of the UP-A is more effective than a waitlist (WL) control group in reducing and preventing symptoms of anxiety and depression when employed as a universal, classroom-based preventive intervention. The secondary aim is to investigate changes in a broad range of secondary outcome measures, including negative and positive affect, anxiety sensitivity, emotional avoidance, top problems ratings, school grades, depression and anxiety-related interference, self-esteem, life satisfaction, quality of life, conduct problems, hyperactivity/inattention symptoms, peer problems, prosocial behavior, school adjustment, and discipline problems. Other aims are to assess a range of possible predictors of intervention effects and to examine the feasibility and the acceptability of implementing UP-A in a prevention group format and in a school setting. Methods A cluster, randomized, WL, controlled trial design with classroom as the unit of randomization was used in this study. Five classes including a total of 152 adolescents were randomized to the experimental or WL control groups. Participants in the experimental group received 9 55-minute sessions delivered by advanced doctoral and masters students in clinical psychology. The WL control group will receive the intervention once the 3-month follow-up assessment is completed. Results We have recruited participants to the cluster randomized controlled trial (RCT) and have conducted the intervention with the experimental group. We expect the WL control group to complete the intervention in July 2017. Data analysis will take place during the second semester of 2017. Conclusions We expect the experimental group to outperform the WL control group at post-intervention and 3-month follow-up. We also expect the WL control group to show improvements in primary and secondary outcome measures after receiving the intervention. Results will have implications for researchers, families, and education providers. Trial Registration Clinicaltrials.gov NCT03123991; https://clinicaltrials.gov/ct2/show/NCT03123991 (Archived by WebCite at http://www.webcitation.org/6qp7GIzcR) PMID:28827212
The Effect of Carbonate, Oxalate and Peroxide on the Cesium Loading of Ionsiv IE-910 and IE-911
DOE Office of Scientific and Technical Information (OSTI.GOV)
Fondeur, F.F.
2000-12-19
The Savannah River Site (SRS) continues to examine three processes for the removal of radiocesium from high-level waste. One option involves the use of crystalline silicotitanate (CST) as a non-elutable ion exchange medium. The process uses CST in its engineered form - IONSIV IE-911 made by UOP, LLC. - in a column to contact the liquid waste. Cesium exchanges with sodium ions residing inside the CST particles. The design disposes of the cesium-loaded CST by vitrification within the Defense Waste Processing Facility.
Physics Features of TRU-Fueled VHTRs
Lewis, Tom G.; Tsvetkov, Pavel V.
2009-01-01
The current waste management strategy for spent nuclear fuel (SNF) mandated by the US Congress is the disposal of high-level waste (HLW) in a geological repository at Yucca Mountain. Ongoing efforts on closed-fuel cycle options and difficulties in opening and safeguarding such a repository have led to investigations of alternative waste management strategies. One potential strategy for the US fuel cycle would be to make use of fuel loadings containing high concentrations of transuranic (TRU) nuclides in the next-generation reactors. The use of such fuels would not only increase fuel supply but could also potentially facilitate prolonged operation modes (viamore » fertile additives) on a single fuel loading. The idea is to approach autonomous operation on a single fuel loading that would allow marketing power units as nuclear batteries for worldwide deployment. Studies have already shown that high-temperature gas-cooled reactors (HTGRs) and their Generation IV (GEN IV) extensions, very-high-temperature reactors (VHTRs), have encouraging performance characteristics. This paper is focused on possible physics features of TRU-fueled VHTRs. One of the objectives of a 3-year U.S. DOE NERI project was to show that TRU-fueled VHTRs have the possibility of prolonged operation on a single fuel loading. A 3D temperature distribution was developed based on conceivable operation conditions of the 600 MWth VHTR design. Results of extensive criticality and depletion calculations with varying fuel loadings showed that VHTRs are capable for autonomous operation and HLW waste reduction when loaded with TRU fuel.« less
Advanced High-Level Waste Glass Research and Development Plan
DOE Office of Scientific and Technical Information (OSTI.GOV)
Peeler, David K.; Vienna, John D.; Schweiger, Michael J.
2015-07-01
The U.S. Department of Energy Office of River Protection (ORP) has implemented an integrated program to increase the loading of Hanford tank wastes in glass while meeting melter lifetime expectancies and process, regulatory, and product quality requirements. The integrated ORP program is focused on providing a technical, science-based foundation from which key decisions can be made regarding the successful operation of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) facilities. The fundamental data stemming from this program will support development of advanced glass formulations, key process control models, and tactical processing strategies to ensure safe and successful operations formore » both the low-activity waste (LAW) and high-level waste (HLW) vitrification facilities with an appreciation toward reducing overall mission life. The purpose of this advanced HLW glass research and development plan is to identify the near-, mid-, and longer-term research and development activities required to develop and validate advanced HLW glasses and their associated models to support facility operations at WTP, including both direct feed and full pretreatment flowsheets. This plan also integrates technical support of facility operations and waste qualification activities to show the interdependence of these activities with the advanced waste glass (AWG) program to support the full WTP mission. Figure ES-1 shows these key ORP programmatic activities and their interfaces with both WTP facility operations and qualification needs. The plan is a living document that will be updated to reflect key advancements and mission strategy changes. The research outlined here is motivated by the potential for substantial economic benefits (e.g., significant increases in waste throughput and reductions in glass volumes) that will be realized when advancements in glass formulation continue and models supporting facility operations are implemented. Developing and applying advanced glass formulations will reduce the cost of Hanford tank waste management by reducing the schedule for tank waste treatment and reducing the amount of HLW glass for storage, transportation, and disposal. Additional benefits will be realized if advanced glasses are developed that demonstrate more tolerance for key components in the waste (such as Al 2O 3, Cr 2O 3, SO 3 and Na 2O) above the currently defined WTP constraints. Tolerating these higher concentrations of key waste loading limiters may reduce the burden on (or even eliminate the need for) leaching to remove Cr and Al and washing to remove excess S and Na from the HLW fraction. Advanced glass formulations may also make direct vitrification of the HLW fraction without significant pretreatment more cost effective. Finally, the advanced glass formulation efforts seek not only to increase waste loading in glass, but also to increase glass production rate. When coupled with higher waste loading, ensuring that all of the advanced glass formulations are processable at or above the current contract processing rate leads to significant improvements in waste throughput (the amount of waste being processed per unit time),which could significantly reduce the overall WTP mission life. The integration of increased waste loading, reduced leaching/washing requirements, and improved melting rates provides a system-wide approach to improve the effectiveness of the WTP process.« less
Martín Fernández, Jesús; Gómez Gascón, Tomás; Martínez García-Olalla, Carlos; del Cura González, María Isabel; Cabezas Peña, María Carmen; García Sánchez, Salvador
2008-07-01
To establish the CVP-35 evaluative properties to measure the professional quality of life (PQL). Prospective, observational study. A primary care area in the Community of Madrid, Spain. A total of 149 sanitary workers with some burnout sign measured by Maslach Burnout Inventory (MBI) participated. They fulfilled MBI, Goldberg Health Questionnaire (GHQ-28), and CVP-35 questionnaires at the beginning and after a year of follow-up, in which 73 subjects took part in activities for coping stress. It was assessed the change of PQL and their domains managerial support (PQL-MS), work load (PQL-WL), intrinsic motivation (PQL-IM) for the subjects with variations at the MBI, or GHQ-28 punctuation greater than 0.5 SD of the initial distribution. Variations in CVP-35 and their domains correlate weakly with changes in MBI and GHQ-28 (r<0.500), but they are congruent with the conceptual model. In the individuals with significant variations in the GHQ-28, they appreciate an average change in PQL and their domains between 0.18 and 0.55 points (absolute value). In those with significant variations in the MBI domains, PQL presented average absolute variations between 0.23 and 0.45 points, PQL-MS between 0.30 and 0.67, PQL-WL between 0.01 and 0.55 and PQL-IM between 0.22 and 0.83 points. CVP-35 is a sensitive-to-change instrument under population point of view. Changes in PQL perception or in any of their domains of 0.5 points could be pointed as relevant.
The role of frit in nuclear waste vitrification
DOE Office of Scientific and Technical Information (OSTI.GOV)
Vienna, J.D.; Smith, P.A.; Dorn, D.A.
1994-04-01
Vitrification of nuclear waste requires additives which are often vitrified independently to form a frit. Frit composition is formulated to meet the needs of glass composition and processing. The effects of frit on melter feed and melt processing, glass acceptance, and waste loading is of practical interest in understanding the trade-offs associated with the competing demands placed on frit composition. Melter feed yield stress, viscosity and durability of frits and corresponding waste glasses as well as the kinetics of elementary melting processes have been measured. The results illustrate the competing requirements on frit. Four frits (FY91, FY93, HW39-4, and SR202)more » and simulated neutralized current acid waste (NCAW) were used in this study. The experimental evidence shows that optimization of frit for one processing related property often results in poorer performance for the remaining properties. The difficulties associated with maximum waste loading and durability are elucidated for glasses which could be processed using technology available for the previously proposed Hanford Waste Vitrification Plant.« less
ROAD MAP FOR DEVELOPMENT OF CRYSTAL-TOLERANT HIGH LEVEL WASTE GLASSES
DOE Office of Scientific and Technical Information (OSTI.GOV)
Fox, K.; Peeler, D.; Herman, C.
The U.S. Department of Energy (DOE) is building a Tank Waste Treatment and Immobilization Plant (WTP) at the Hanford Site in Washington to remediate 55 million gallons of radioactive waste that is being temporarily stored in 177 underground tanks. Efforts are being made to increase the loading of Hanford tank wastes in glass while meeting melter lifetime expectancies and process, regulatory, and product quality requirements. This road map guides the research and development for formulation and processing of crystaltolerant glasses, identifying near- and long-term activities that need to be completed over the period from 2014 to 2019. The primary objectivemore » is to maximize waste loading for Hanford waste glasses without jeopardizing melter operation by crystal accumulation in the melter or melter discharge riser. The potential applicability to the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) will also be addressed in this road map. The planned research described in this road map is motivated by the potential for substantial economic benefits (significant reductions in glass volumes) that will be realized if the current constraints (T1% for WTP and TL for DWPF) are approached in an appropriate and technically defensible manner for defense waste and current melter designs. The basis of this alternative approach is an empirical model predicting the crystal accumulation in the WTP glass discharge riser and melter bottom as a function of glass composition, time, and temperature. When coupled with an associated operating limit (e.g., the maximum tolerable thickness of an accumulated layer of crystals), this model could then be integrated into the process control algorithms to formulate crystal-tolerant high-level waste (HLW) glasses targeting high waste loadings while still meeting process related limits and melter lifetime expectancies. The modeling effort will be an iterative process, where model form and a broader range of conditions, e.g., glass composition and temperature, will evolve as additional data on crystal accumulation are gathered. Model validation steps will be included to guide the development process and ensure the value of the effort (i.e., increased waste loading and waste throughput). A summary of the stages of the road map for developing the crystal-tolerant glass approach, their estimated durations, and deliverables is provided.« less
Assessing musculoskeletal disorders among municipal waste loaders of Mumbai, India.
Salve, Pradeep; Chokhandre, Praveen; Bansod, Dhananjay
2017-10-06
The study aims to assess the impact of municipal waste loading occupation upon developing musculoskeletal disorders (MSDs) and thereby disabilities among waste loaders. Additionally, the study has identified the potential risk factors raising MSDs and disabilities. A cross-sectional case-control design survey was conducted in 6 out of 24 municipal wards of Mumbai during March-September 2015. The study population consisted of municipal waste loaders (N = 180) and a control group (N = 180). The Standardized Modified Nordic questionnaire was adopted to measures the MSDs and thereby disabilities in the past 12 months. A Propensity Score Matching (PSM) method was applied to assess the impact of waste loading occupation on developing MSDs and disabilities. Waste loaders had a significantly higher risk of developing MSDs as well as disabilities than the control group particularly for low back, hip/ thigh upper back and shoulder. Propensity Score Matching results revealed that the MSDs were significantly higher among waste loaders for hip/thigh (22%), low back (19%), shoulder (18%), and upper back (15%) than matched control group. Likewise, MSDs-related disabilities were found to be significantly higher among waste loaders for low back (20%), hip/ thigh (18%) upper back (13%) and shoulder (8%) than the control group. Duration of work, substance use and mental health were found to be the potential psychosocial factors for developing the risk of MSDs and disabilities. The municipal waste loading occupation raised the risk of MSDs and related disabilities among waste loaders compared to the control group. The preventive and curative measures are strongly recommended to minimize the burden of MSDs and disabilities. Int J Occup Med Environ Health 2017;30(6):875-886. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.
Development of a Database of Thermochemical Parameters for Use with the SOLGASMIX Computer Program
1988-07-01
TITANIUM CHLORIDE (TICL4) CL4Wl(CR) TUNGSTEN CHLORIDE (WCL4) CL4Wl(G) TUNGSTEN CHLORIDE (WCL4) CL4ZR1(CR) ZIRCONIUM CHLORIDE ( ZRCL4 ) CL4ZR1(G) ZIRCONIUM...CHLORIDE ( ZRCL4 ) % % % CL5MO1(CR) MOLYBDENUM CHLORIDE (MOCL5) CL5MO1(CR,L) MOLYBDENUM CHLORIDE (MOCL5) CL5MO1(G) MOLYBDENUM CHLORIDE (MOCL5) CL5MOI(L
Observing the Ultrahigh Energy Universe with OWL Eyes
NASA Technical Reports Server (NTRS)
Stecker, F. W.; Krizmanic, J. F.; Barbier, L. M.; Loh, E.; Mitchell, J. W.; Sokolsky, P.; Streitmatter, R. E.
2004-01-01
The goal of the Orbiting Wide-field Light-collectors (0WL) mission is to study the origin and physics of the highest energy particles known in nature, the ultra- high energy cosmic rays (UHECRs). The OWL mission consists of telescopes with UV sensitive cameras on two satellites operating in tandem to view in stereo the development of the giant particle showers induced in the Earth s atmosphere by UHECRs. This paper discusses the characteristics of the 0WL mission.
NASA Technical Reports Server (NTRS)
Taylor, E. W.; Berry, J. N.; Sanchez, A. D.; Padden, R. J.; Chapman, S. P.
1992-01-01
A brief overview of the analyses performed to date on WL Experiment-701 is presented. Four active digital fiber optic links were directly exposed to the space environment for a period of 2114 days. The links were situated aboard the Long Duration Exposure Facility (LDEF) with the cabled, single fiber windings atop an experimental tray containing instrumentation for exercising the experiment in orbit. Despite the unplanned and prolonged exposure to trapped and galactic radiation, wide temperature extremes, atomic oxygen interactions, and micro-meteorite and debris impacts, in most instances the optical data links performed well within the experimental limits. Analysis of the recorded orbital data clearly indicates that fiber optic applications in space will meet with success. Ongoing tests and analysis of the experiment at the Phillips Laboratory's Optoelectronics Laboratory will expand this premise, and establish the first known and extensive database of active fiber optic link performance during prolonged space exposure. WL Exp-701 was designed as a feasibility demonstration for fiber optic technology in space applications, and to study the performance of operating fiber systems exposed to space environmental factors such as galactic radiation, and wide temperature cycling. WL Exp-701 is widely acknowledged as a benchmark accomplishment that clearly demonstrates, for the first time, that fiber optic technology can be successfully used in a variety of space applications.
Suassuna, Fernanda Clotilde Mariz; Maia, Ana Marly Araújo; Melo, Daniela Pita; Antonino, Antônio Celso Dantas; Gomes, Anderson Stevens Leônidas; Bento, Patrícia Meira
2018-02-01
To comparein vitro differences in the apical filling regarding working length (WL) change and presence of voids and to validate optical coherence tomography (OCT) in comparison with computerized microtomography (µCT) for the detection of failures in the apical filling. Forty-five uniradicular teeth with round canals, divided into groups (n = 15) following the obturation protocols: LC (lateral condensation), TMC (thermomechanical compaction) and SC (single cone). Samples were scanned using µCT (parameters: 80 kV, 222 µA, and resolution of 11 µm), OCT (parameters: SSOCT, 1300 nm and axial resolution of 12 µm), and periapical digital radiography. The images were analyzsed by two blind and calibrated observers using ImageJ software to measure the boundary of the obturation WL and voids presence. Categorical and metric data were submitted to inferential analysis, and the validity of the OCT as a diagnostic test was assessed with performance and reliability tests. The WL average remained constant for all obturation techniques and image methods. OCT showed adequate sensitivity and specificity to detect voids in the WL of apical obturations in vitro in comparison with µCT. Both image methods found a higher number of voids for LC technique (µCT p = 0.011/OCT p = 0.002). OCT can be used in apical obturation voids assessment and the LC technique revealed more voids with larger dimensions.
Almanza-Aguilera, Enrique; Brunius, Carl; Bernal-Lopez, M Rosa; Garcia-Aloy, Mar; Madrid-Gambin, Francisco; Tinahones, Francisco J; Gómez-Huelgas, Ricardo; Landberg, Rikard; Andres-Lacueva, Cristina
2018-06-28
Little is known regarding metabolic benefits of weight loss (WL) on the metabolically healthy obese (MHO) patients. We aimed to examine the impact of a lifestyle weight loss (LWL) treatment on the plasma metabolomic profile in MHO individuals. Plasma samples from 57 MHO women allocated to an intensive LWL treatment group (TG, hypocaloric Mediterranean diet and regular physical activity, n = 30) or to a control group (CG, general recommendations of a healthy diet and physical activity, n = 27) were analyzed using an untargeted 1 H NMR metabolomics approach at baseline, after 3 months (intervention), and 12 months (follow-up). The impact of the LWL intervention on plasma metabolome was statistically significant at 3 months but not at follow-up and included higher levels of formate and phosphocreatine and lower levels of LDL/VLDL (signals) and trimethylamine in the TG. These metabolites were also correlated with WL. Higher myo-inositol, methylguanidine, and 3-hydroxybutyrate, and lower proline, were also found in the TG; higher levels of hippurate and asparagine, and lower levels of 2-hydroxybutyrate and creatine, were associated with WL. The current findings suggest that an intensive LWL treatment, and the consequent WL, leads to an improved plasma metabolic profile in MHO women through its impact on energy, amino acid, lipoprotein, and microbial metabolism.
NASA Technical Reports Server (NTRS)
Van Volkenburgh, E.; Cleland, R. E.
1990-01-01
Cell expansion in dicotyledonous leaves is strongly stimulated by bright white light (WL), at least in part as a result of light-induced acidification of the cell walls. It has been proposed that photosynthetic reactions are required for light-stimulated transport processes across plasma membranes of leaf cells, including proton excretion. The involvement of photosynthesis in growth and wall acidification of primary leaves of bean has been tested by inhibiting photosynthesis in two ways: by reducing chlorophyll content of intact plants with tentoxin (TX) and by treating leaf discs with 3-(3,4-dichlorophenyl)-1,1-dimethylurea (DCMU). Exposure to bright WL stimulated growth of intact leaves of TX-treated plants. Discs excised from green as well as from TX-or DCMU-treated leaves also responded by growing faster in WL, as long as exogenous sucrose was supplied to the photosynthetically inhibited tissues. The WL caused acidification of the epidermal surface of intact TX-leaves, but acidification of the incubation medium by mesophyll cells only occurred when photosynthesis was not inhibited. It is concluded that light-stimulated cell enlargement of bean leaves, and the necessary acidification of epidermal cell walls, are mediated by a pigment other than chlorophyll. Light-induced proton excretion by mesophyll cells, on the other hand, may require both a photosynthetic product (or exogenous sugars) and a non-photosynthetic light effect.
Cleaning of Root Canal System by Different Irrigation Methods.
Tanomaru-Filho, Mário; Miano, Lucas Martinati; Chávez-Andrade, Gisselle Moraima; Torres, Fernanda Ferrari Esteves; Leonardo, Renato de Toledo; Guerreiro-Tanomaru, Juliane Maria
2015-11-01
The aim of this study was to compare the cleaning of main and lateral canals using the irrigation methods: negative pressure irrigation (EndoVac system), passive ultrasonic irrigation (PUI) and manual irrigation (MI). Resin teeth were used. After root canal preparation, four lateral canals were made at 2 and 7 mm from the apex. Root canals were filled with contrast solution and radiographed pre- and post-irrigation using digital radiographic system [radiovisiography (RVG)]. The irrigation protocols were: MI1-manual irrigation [22 G needle at 5 mm short of working length-WL]; MI2-manual irrigation (30G needle at 2 mm short of WL); PUI; EV1-EndoVac (microcannula at 1 mm short of WL); EV2-Endovac (microcannula at 3 mm short of WL). The obtained images, initial (filled with contrast solution) and final (after irrigation) were analyzed by using image tool 3.0 software. Statistical analysis was performed by analysis of variance (ANOVA) and Tukey tests (5% significance level). EV1 and EV2, followed by PUI showed better cleaning capacity than manual irrigation (MI1 and MI2) (p < 0.05). Negative pressure irrigation and PUI promoted better cleaning of main and simulated lateral canals. Conventional manual irrigation technique may promote less root canal cleaning in the apical third. For this reason, the search for other irrigation protocols is important, and EndoVac and PUI are alternatives to contribute to irrigation effectiveness.
Maryam, Ehsani; Farida, Abesi; Farhad, Akbarzade; Soraya, Khafri
2013-11-01
Obtaining the proper working length in endodontic treatment is essential. The aim of this study was to compare the working length (WL) assessment of small diameter K-files using the two different digital imaging methods. The samples for this in-vitro experimental study consisted of 40 extracted single-rooted premolars. After access cavity preparation, the ISO files no. 6, 8, and 10 stainless steel K-files were inserted in the canals in the three different lengths to evaluate the results in a blinded manner: At the level of apical foramen(actual)1 mm short of apical foramen2 mm short of apical foramen A digital caliper was used to measure the length of the files which was considered as the Gold Standard. Five observers (two oral and maxillofacial radiologists and three endodontists) observed the digital radiographs which were obtained using PSP and CCD digital imaging sensors. The collected data were analyzed by SPSS 17 and Repeated Measures Paired T-test. In WL assessment of small diameter K-files, a significant statistical relationship was seen among the observers of two digital imaging techniques (P<0.001). However, no significant difference was observed between the two digital techniques in WL assessment of small diameter K-files (P<0.05). PSP and CCD digital imaging techniques were similar in WL assessment of canals using no. 6, 8, and 10 K-files.
40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2012 CFR
2012-07-01
... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...
40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2011 CFR
2011-07-01
... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...
40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2013 CFR
2013-07-01
... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...
40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2010 CFR
2010-07-01
... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...
40 CFR 60.1810 - How do I monitor the load of my municipal waste combustion unit?
Code of Federal Regulations, 2014 CFR
2014-07-01
... municipal waste combustion unit? 60.1810 Section 60.1810 Protection of Environment ENVIRONMENTAL PROTECTION... Guidelines and Compliance Times for Small Municipal Waste Combustion Units Constructed on or Before August 30... combustion unit? (a) If your municipal waste combustion unit generates steam, you must install, calibrate...
Utilization of solid catfish manure waste as carbon and nutrient source for lactic acid production.
Shi, Suan; Li, Jing; Blersch, David M
2018-06-01
The aim of this work was to study the solid waste (manure) produced by catfish as a potential feedstock for the production of lactic acid (LA) via fermentation. The solid waste contains high levels of both carbohydrates and nutrients that are sufficient for LA bacteria. Simultaneous saccharification and co-fermentation (SSCF) was applied using enzyme and Lactobacillus pentosus, and different loadings of enzyme and solid waste were tested. Results showed LA concentrations of 35.7 g/L were obtained at 15% solids content of catfish waste. Because of the high nutrient content in the fish waste, it could also be used as supplementary substrate for nitrogen and carbon sources with other lignocellulosic materials. A combined feedstock of catfish waste and paper mill sludge was tested, increasing the final LA concentration to 43.1 g/L at 12% solids loading. The catfish waste was shown to be a potential feedstock to provide both carbon and nutrients for LA production, suggesting its use as a sole substrate or in combination with other lignocellulosic materials.
Comparison of waste combustion and waste electrolysis - A systems analysis
NASA Technical Reports Server (NTRS)
Holtzapple, Mark T.; Little, Frank E.
1989-01-01
A steady state model of a closed environmental system has been developed which includes higher plant growth for food production, and is designed to allow wastes to be combusted or electrolyzed. The stoichiometric equations have been developed to evaluate various trash compositions, food items (both stored and produced), metabolic rates, and crew sizes. The advantages of waste electrolysis versus combustion are: (1) oxygen is not required (which reduces the load on the oxygen producing system); (2) the CO2 and H2 products are produced in pure form (reducing the load on the separators); and (3) nitrogen is converted to nitrate (which is directly usable by plants). Weight tradeoff studies performed using this model have shown that waste electrolysis reduces the life support weight of a 4-person crew by 1000 to 2000 kg.
Salzer, Simone; Stefini, Annette; Kronmüller, Klaus-Thomas; Leibing, Eric; Leichsenring, Falk; Henningsen, Peter; Peseschkian, Hamid; Reich, Günter; Rosner, Rita; Ruhl, Uwe; Schopf, Yvonne; Steinert, Christiane; Vonderlin, Eva; Steil, Regina
2018-06-12
Although social anxiety disorder (SAD) has an early onset and is frequently found in adolescence, evidence for psychotherapeutic treatments of SAD in adolescents is rather scarce. Within the Social Phobia Psychotherapy Research Network (SOPHO-NET), we examined the efficacy of cognitive-behavioral (CBT) and psychodynamic therapy (PDT) compared to a waiting list (WL) in these patients. In a multicenter randomized controlled superiority trial, 107 patients, aged 14-20 years, were randomized to CBT (n = 34), PDT (n = 34), or WL (n = 39). Assessments were made at baseline, at the end of treatment, and 6 and 12 months after termination. The Liebowitz Social Anxiety Scale for Children and Adolescents (LSAS-CA) applied by raters masked to the treatment condition was used as the primary outcome. As secondary outcomes, rates of response and remission and the Social Phobia Anxiety Inventory (SPAI) were used. Both treatments were superior to WL in the LSAS-CA (CBT: p = 0.0112, d = 0.61, 95% CI 0.14-1.08; PDT: p = 0.0261, d = 0.53, 95% CI 0.06-1.00). At the end of treatment, response rates were 66, 54, and 20% for CBT, PDT, and WL. The corresponding remission rates were 47, 34, and 6%, respectively. CBT and PDT were significantly superior to WL regarding remission (CBT: p = 0.0009, h = 1.0; PDT: p = 0.0135, h = 0.74), response (CBT: p = 0.0004, h = 0.97; PDT: p = 0.0056, h = 0.72), and the SPAI (CBT: p = 0.0021, d = 0.75, 95% CI 0.27-1.22; PDT: p = 0.0060, d = 0.66, 95% CI 0.19-1.13). Treatment effects were stable at 6- and 12-month follow-ups. These results are comparable to the large SOPHO-NET trial in adults (n = 495). Early treatments for social anxiety are needed in order to prevent chronic manifestation of SAD. © 2018 S. Karger AG, Basel.
Flemming, Jennifer A; Vagefi, Parsia A; Freise, Chris E; Yao, Francis Y; Terrault, Norah A
2014-10-01
Older donor age is associated with lower graft and patient survival among all recipients of liver transplantation (LT). Among patients with hepatitis C virus (HCV), donor age is one of the strongest predictors of fibrosis severity and graft loss. We evaluated the implementation of a donor age restriction policy for LT patients with HCV at a single center and the effects that this policy had on wait-list (WL) and post-LT outcomes for HCV and non-HCV patients. This was a cohort study of 2388 WL patients and 1015 LT recipients between March 2002 and January 2013 and reflected 3 different eras of donor age policies. With the donor age restriction, the median donor age was reduced in LT recipients with HCV versus LT recipients without HCV (30 versus 48 years, P < 0.001) without differences in the WL time (10.6 versus 8.0 months, P = 0.23). According to a competing risks regression, those with HCV and those without HCV had lower subhazard ratios (SHRs) of dropout or death on the WL during the donor age restriction era versus the era without donor age restriction [SHR = 0.68 (P < 0.01) and SHR = 0.64 (P = 0.01), respectively]. No differences were seen in early post-LT survival for patients with or without HCV between eras (P = 0.7 and P = 0.88, respectively). In conclusion, we show that donor age restriction for HCV results in a lower donor age for HCV recipients without obvious adverse WL consequences. Although additional studies are needed, our results demonstrate the feasibility of donor age restriction for LT recipients with HCV, and such information may be relevant to programs with limited access to new antiviral therapies for which modifying the risk of severe disease remains of paramount importance. © 2014 American Association for the Study of Liver Diseases.
SU-F-J-53: A 3D Printed Phantom for the Use of Daily Quality Assurance Alignment Tests
DOE Office of Scientific and Technical Information (OSTI.GOV)
Woods, K; Ayan, A; Woollard, J
Purpose: To discuss experiences and results for a 3D printed QA phantom used for daily alignment purposes for a six degrees-of-freedom (6DoF) table Methods: A 3D model was created using a fused deposition modeling (FDM) printer using free online computer-aided design (CAD) software. The model has been under use for daily QA alignment tests for a 6DoF couch. An aligned and angled baseplate were also printed in order to introduce known angles for 6DoF corrections during image-guidance. Unique registration contours were created on the faces of the phantom in order to achieve a better cone-beam computed tomography (CBCT) match usingmore » an auto-registration algorithm. A BB was also introduced at the center of the phantom in order to deliver an integrated daily Winston-Lutz (WL) test. Translational, rotational, and WL results were tabulated over one month. Results: The ’honeycomb’ structure of the print was apparent in the EPID images for the WL test, which affected the results of the analysis software. This was fixed by inserting a cube made of polyoxymethylene within the 3D phantom that encompass the BB. Auto-registration results for the three translational and three rotational from a known offset to the BB isocenter consistently fell within 1 mm and 0.2°, respectively. WL tests resulted in an average of 0.71 ± 0.14 mm. Conclusion: 3D printed models allow for accurate builds that can be customized to a variety of clinical needs. Results from translational, rotational, and WL show consistent results over a month’s time. Given its relatively cheap and streamlined workflow, 3D printing could be implemented into any clinic looking to create customized phantoms.« less
Hodges, L D; Nielsen, T; Baken, D
2017-08-07
To compare physiological responses of chronic fatigue syndrome (CFS/ME), multiple sclerosis (MS) and healthy controls (HC) following a 24-h repeated exercise test. Ten CFS, seven MS and 17 age- and gender-matched healthy controls (10, CFS HC; and seven, MS HC) were recruited. Each participant completed a maximal incremental cycle exercise test on day 1 and again 24 h later. Heart rate (HR), blood pressure (BP), rating of perceived exertion (RPE), oxygen consumption (V˙O2), carbon dioxide production and workload (WL) were recorded. Data analysis investigated these responses at anaerobic threshold (AT) and peak work rate (PWR). On day 2, both CFS and MS had significantly reduced max workload compared to HC. On day 2, significant differences were apparent in WL between CFS and CFS HC (93 ± 37 W, 132 ± 42 W, P<0·042). CFS workload decreased on day 2, alongside a decrease in HR but with an increase in V˙O2 (ml kg min -1 ). This was in comparison with an increase in WL, HR and V˙O2 for CFS HC. MS demonstrated a decreased WL compared to MS HC on both days of the study (D1 81 ± 30 W, 116 ±30 W; D2 84 ± 29 W, 118 ± 36 W); however, patients with MS were able to achieve a higher WL on day 2 alongside MS HC. These results suggest that exercise exhibits a different physiological response in MS and CFS/ME, demonstrating repeated cardiovascular exercise testing as a valid measure for differentiating between fatigue conditions. © 2017 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kaminski, Michael D.; Mertz, Carol J.
2016-01-01
The physical properties of a surrogate waste form containing cesium, strontium, rubidium, and barium sintered into bentonite clay were evaluated for several simulant feed streams: chlorinated cobalt dicarbollide/polyethylene glycol (CCD-PEG) strip solution, nitrate salt, and chloride salt feeds. We sintered bentonite clay samples with a loading of 30 mass% of cesium, strontium, rubidium, and barium to a density of approximately 3 g/cm 3. Sintering temperatures of up to 1000°C did not result in volatility of cesium. Instead, there was an increase in crystallinity of the waste form upon sintering to 1000ºC for chloride- and nitrate-salt loaded clays. The nitrate saltmore » feed produced various cesium pollucite phases, while the chloride salt feed did not produce these familiar phases. In fact, many of the x-ray diffraction peaks could not be matched to known phases. Assemblages of silicates were formed that incorporated the Sr, Rb, and Ba ions. Gas evolution during sintering to 1000°C was significant (35% weight loss for the CCD-PEG waste-loaded clay), with significant water being evolved at approximately 600°C.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Mohd Fadzil, Syazwani Binti; Hrma, Pavel R.; Schweiger, Michael J.
Pyroprocessing is a reprocessing method for managing and reusing used nuclear fuel (UNF) by dissolving it in an electrorefiner with a molten alkali or alkaline earth chloride salt mixture while avoiding wet reprocessing. Pyroprocessing UNF with a LiCl-KCl eutectic salt releases the fission products from the fuel and generates a variety of metallic and salt-based species, including rare earth (RE) chlorides. If the RE-chlorides are converted to oxides, borosilicate glass is a prime candidate for their immobilization because of its durability and ability to dissolve almost any RE waste component into the matrix at high loadings. Crystallization that occurs inmore » waste glasses as the waste loading increases may complicate glass processing and affect the product quality. This work compares three types of borosilicate glasses in terms of liquidus temperature (TL): the International Simple Glass designed by the International Working Group, sodium borosilicate glass developed by Korea Hydro and Nuclear Power, and the lanthanide aluminoborosilicate (LABS) glass established in the United States. The LABS glass allows the highest waste loadings (over 50 mass% RE2O3) while possessing an acceptable chemical durability.« less
NASA Astrophysics Data System (ADS)
Mohd Fadzil, Syazwani; Hrma, Pavel; Schweiger, Michael J.; Riley, Brian J.
2015-10-01
Pyroprocessing is are processing method for managing and reusing used nuclear fuel (UNF) by dissolving it in an electrorefiner with a molten alkali or alkaline earth chloride salt mixture while avoiding wet reprocessing. Pyroprocessing UNF with a LiCl-KCl eutectic salt releases the fission products from the fuel and generates a variety of metallic and salt-based species, including rare earth (RE) chlorides. If the RE-chlorides are converted to oxides, borosilicate glass is a prime candidate for their immobilization because of its durability and ability to dissolve almost any RE waste component into the glass matrix at high loadings. Crystallization that occurs in waste glasses as the waste loading increases may complicate glass processing and affect the product quality. This work compares three types of borosilicate glasses in terms of liquidus temperature (TL): the International Simple Glass designed by the International Working Group, sodium borosilicate glass developed by Korea Hydro and Nuclear Power, and the lanthanide aluminoborosilicate (LABS) glass established in the United States. The LABS glass allows the highest waste loadings (over 50 mass% RE2O3) while possessing an acceptable chemical durability.
Investigation of Poultry Waste for Anaerobic Digestion: A Case Study
NASA Astrophysics Data System (ADS)
Salam, Christopher R.
Anaerobic Digestion (AD) is a biological conversion technology which is being used to produce bioenergy all over the world. This energy is created from biological feedstocks, and can often use waste products from various food and agricultural processors. Biogas from AD can be used as a fuel for heating or for co-generation of electricity and heat and is a renewable substitute to using fossil fuels. Nutrient recycling and waste reduction are additional benefits, creating a final product that can be used as a fertilizer in addition to energy benefits. This project was conducted to investigate the viability of three turkey production wastes as AD feedstock: two turkey litters and a material separated from the turkey processing wastewater using dissolved air flotation (DAF) process. The DAF waste contained greases, oils and other non-commodity portions of the turkey. Using a variety of different process methods, types of bacteria, loading rates and food-to-microorganism ratios, optimal loading rates for the digestion of these three materials were obtained. In addition, the co-digestion of these materials revealed additional energy benefits. In this study, batch digestion tests were carried out to treat these three feedstocks, using mesophilic and thermophilic bacteria, using loading rates of 3 and 6 gVS/L They were tested separately and also as a mixture for co-digestion. The batch reactor used in this study had total and working volumes of 1130 mL and 500 mL, respectively. The initial organic loading was set to be 3 gVS/L, and the food to microorganism ratio was either 0.6 or 1.0 for different treatments based on the characteristics of each material. Only thermophilic (50 +/- 2ºC) temperatures were tested for the litter and DAF wastes in continuous digestion, but mesophilic and thermophilic batch digestion experiments were conducted. The optimum digestion time for all experiments was 14 days. The biogas yields of top litter, mixed litter, and DAF waste under mesophilic batch conditions all at 3 gVS/L loading were determined to be 148.6 +/- 7.82, 176.5 +/- 11.1 and 542.0 +/- 37.9 mL/ gVS, respectively and were 201.9 +/- 10.0, 210.4 +/- 29.3, and 419.3 +/- 12.1 mL/gVS, respectively, for initial loading of 6 gVS/L. Under thermophilic batch conditions, the top litter, mixed litter, and DAF waste had the biogas yields of 255.3 +/- 7.9, 313.4 +/- 30.1and 297.4 +/- 33.8 mL/gVS for loading rate of 3 gVS/L and 233.8 +/- 45.3, 306.5 +/- 11.8 and 185.1 +/- 0.85 mL/gVS for loading rate of 6 gVS/L. The biogas yields from co-digestion of the mixed litter and DAF waste at 3 gVS/L were 461.8 +/- 41.3 mL/gVS under thermophilic conditions. The results from batch anaerobic digestion tests were then used for designing continuous digestion experiments. All the continuous digestion experiments were conducted by using an Anaerobic Phase Solids (APS) digester system operated at a thermophilic temperature. The total volume of the continuous digester system was 4.8 L and the working volume was around 4.4 L. The APS digester system had two hydrolysis reactors and one biogasification reactor. Feedstock was loaded into the hydrolysis reactors in batches. The feedstock digestion time was 14 days and the average organic loading rate (OLR) of the system was 3 gVS/L/day. The experiment has three distinct feedstock stages, first with turkey litter waste, a co-digestion of DAF and turkey litter waste, followed by DAF waste. The biogas yields were determined to be 305.2 +/- 70.6 mL/gVS/d for turkey mixed litter, 455.8 +/- 77.2 mL/gVS/d during the mixture of mixed litter and DAF waste, and 382.0 +/- 39.6 mL/gVS for DAF waste. The biogas yields from the thermophilic batch test yields compare with that of the continuous digester yields. For experiments utilizing turkey litter, batch tests yielded 313.4 +/- 30.1mL/gVS biogas and 305.2 +/- 70.6 mL/gVS/d for continuous experiments. For experiments using codigestion of turkey litter and DAF waste, batches yielded 461.8 +/- 41.3 mL/gVS biogas comparing well to continuous digester operation that yielded 455.8 +/- 77.2 mL/gVS/d. It was mainly in the case for DAF that batch vs. continuous digester testing yielded a significant difference in performance. For experiments using DAF waste, batches yielded 297.4 +/- 33.8 mL/gVS biogas and continuous digester operation yielded 455.8 +/- 77.2 mL/gVS/d. For a case study on the APS digester system, mesophilic DAF waste was chosen as the optimum substrate. Using this material and reactor condition, a case study was built using provided information and experimental results to build a simulation. A reactor site needed to process 11,800 kgVS of DAF waste would require 4,800 m3 of tank volume, and use nearly 4,000 m3 as working volume. This reactor was modeled after a 2 stage APS reactor, with 2 hydrolysis reactors and 1 biogasification reactor, and had a 14 day retention time and a 3 gVS/L/d organic loading rate. The expected biogas output was 550 mL/gVS, and expected waste reduction was 20%. The reactor would produce 7,113 m3/d of biogas, and would be burned for 127,223 MJ/d.
Anaerobic digestion of municipal solid wastes containing variable proportions of waste types.
Akunna, J C; Abdullahi, Y A; Stewart, N A
2007-01-01
In many parts of the world there are significant seasonal variations in the production of the main organic wastes, food and green wastes. These waste types display significant differences in their biodegradation rates. This study investigated the options for ensuring process stability during the start up and operation of thermophilic high-solids anaerobic digestion of feedstock composed of varying proportions of food and green wastes. The results show that high seed sludge to feedstock ratio (or low waste loading rate) is necessary for ensuring process pH stability without chemical addition. It was also found that the proportion of green wastes in the feedstock can be used to regulate process pH, particularly when operating at high waste loading rates (or low seed sludge to feedstock ratios). The need for chemical pH correction during start-up and digestion operation decreased with increase in green wastes content of the feedstock. Food wastes were found to be more readily biodegradable leading to higher solids reduction while green wastes brought about pH stability and higher digestate solid content. Combining both waste types in various proportions brought about feedstock with varying buffering capacity and digestion performance. Thus, careful selection of feedstock composition can minimise the need for chemical pH regulation as well as reducing the cost for digestate dewatering for final disposal.
Method for solidification of radioactive and other hazardous waste
Anshits, Alexander G.; Vereshchagina, Tatiana A.; Voskresenskaya, Elena N.; Kostin, Eduard M.; Pavlov, Vyacheslav F.; Revenko, Yurii A.; Tretyakov, Alexander A.; Sharonova, Olga M.; Aloy, Albert S.; Sapozhnikova, Natalia V.; Knecht, Dieter A.; Tranter, Troy J.; Macheret, Yevgeny
2002-01-01
Solidification of liquid radioactive waste, and other hazardous wastes, is accomplished by the method of the invention by incorporating the waste into a porous glass crystalline molded block. The porous block is first loaded with the liquid waste and then dehydrated and exposed to thermal treatment at 50-1,000.degree. C. The porous glass crystalline molded block consists of glass crystalline hollow microspheres separated from fly ash (cenospheres), resulting from incineration of fossil plant coals. In a preferred embodiment, the porous glass crystalline blocks are formed from perforated cenospheres of grain size -400+50, wherein the selected cenospheres are consolidated into the porous molded block with a binder, such as liquid silicate glass. The porous blocks are then subjected to repeated cycles of saturating with liquid waste, and drying, and after the last cycle the blocks are subjected to calcination to transform the dried salts to more stable oxides. Radioactive liquid waste can be further stabilized in the porous blocks by coating the internal surface of the block with metal oxides prior to adding the liquid waste, and by coating the outside of the block with a low-melting glass or a ceramic after the waste is loaded into the block.
Constant load and constant volume response of municipal solid waste in simple shear.
Zekkos, Dimitrios; Fei, Xunchang
2017-05-01
Constant load and constant volume simple shear testing was conducted on relatively fresh municipal solid waste (MSW) from two landfills in the United States, one in Michigan and a second in Texas, at respective natural moisture content below field capacity. The results were assessed in terms of two failure strain criteria, at 10% and 30% shear strain, and two interpretations of effective friction angle. Overall, friction angle obtained assuming that the failure plane is horizontal and at 10% shear strain resulted in a conservative estimation of shear strength of MSW. Comparisons between constant volume and constant load simple shear testing results indicated significant differences in the shear response of MSW with the shear resistance in constant volume being lower than the shear resistance in constant load. The majority of specimens were nearly uncompacted during specimen preparation to reproduce the state of MSW in bioreactor landfills or in uncontrolled waste dumps. The specimens had identical percentage of <20mm material but the type of <20mm material was different. The <20mm fraction from Texas was finer and of high plasticity. MSW from Texas was overall weaker in both constant load and constant volume conditions compared to Michigan waste. The results of these tests suggest the possibility of significantly lower shear strength of MSW in bioreactor landfills where waste is placed with low compaction effort and constant volume, i.e., "undrained", conditions may occur. Compacted MSW specimens resulted in shear strength parameters that are higher than uncompacted specimens and closer to values reported in the literature. However, the normalized undrained shear strength in simple shear for uncompacted and compacted MSW was still higher than the normalized undrained shear strength reported in the literature for clayey and silty soils. Copyright © 2016 Elsevier Ltd. All rights reserved.
The Effects of rhBMP-2 Used for Spinal Fusion on Spinal Cord Pathology After Traumatic Injury
2009-07-29
1219-1224; discussion 1225. Basso DM , Beattie MS, Bresnahan JC (1995) A sensitive and reliable locomotor rating scale for open field testing in rats...usage of rhBMP-2 in the anterior cervical spine. Spine 31:2813-2819. Stuesse SL, Crisp T, McBurney DL, Schechter JB, Lovell JA, Cruce WL (2001...250-256. Stuesse SL, Crisp T, McBurney DL, Schechter JB, Lovell JA, Cruce WL (2001) Neuropathic pain in aged rats: behavioral responses and
Develop Techniques for Ion Implantation of PLZT for Adaptive Optics
1989-11-01
WL-TR-89-26 FIGURES (Continued) Fizure Page 20 EDX elemental spectrum from perovskite region of the sample shown in Fig. 15. 65 21 EDX elemental...pyroelectric response. 126 84 Result of doping PZT with La and Mn (Ref. 7). 127 85 APW results along the lin for several perovskite - type compounds and ReO 2...structure of the calcined powder was analyzed and shown to be mainly the hexagonal/rhombohedral phase within 17 WL-TR-89-26 the perovskite structure of
Gutiérrez-Martínez, Maria del Rosario; Muñoz-Guerrero, Hernán; Alcaína-Miranda, Maria Isabel; Barat, José Manuel
2014-03-01
The salting step in food processes implies the production of large quantities of waste brines, having high organic load, high conductivity, and other pollutants with high oxygen demand. Direct disposal of the residual brine implies salinization of soil and eutrophication of water. Since most of the organic load of the waste brines comes from proteins leaked from the salted product, precipitation of dissolved proteins by acidification and removal by centrifugation is an operation to be used in waste brine cleaning. The aim of this study is optimizing the conditions for carrying out the separation of proteins from waste brines generated in the pork ham salting operation, by studying the influence of pH, centrifugal force, and centrifugation time. Models for determining the removal of proteins depending on the pH, centrifugal force, and time were obtained. The results showed a high efficacy of the proposed treatment for removing proteins, suggesting that this method could be used for waste brine protein removal. The best pH value to be used in an industrial process seems to be 3, while the obtained results indicate that almost 90% of the proteins from the brine can be removed by acidification followed by centrifugation. A further protein removal from the brine should have to be achieved using filtrating techniques, which efficiency could be highly improved as a consequence of the previous treatment through acidification and centrifugation. Waste brines from meat salting have high organic load and electrical conductivity. Proteins can be removed from the waste brine by acidification and centrifugation. The total protein removal can be up to 90% of the initial content of the waste brine. Protein removal is highly dependent on pH, centrifugation rate, and time. © 2014 Institute of Food Technologists®
NASA Astrophysics Data System (ADS)
Ma, Yinbiao; Wei, Xiaojuan
2017-04-01
A novel method for the determination of platinum in waste platinum-loaded carbon catalyst samples was established by inductively coupled plasma optical emission spectrometry after samples digested by microwave oven with aqua regia. Such experiment conditions were investigated as the influence of sample digestion methods, digestion time, digestion temperature and interfering ions on the determination. Under the optimized conditions, the linear range of calibration graph for Pt was 0 ˜ 200.00 mg L-1, and the recovery was 95.67% ˜ 104.29%. The relative standard deviation (RSDs) for Pt was 1.78 %. The proposed method was applied to determine the same samples with atomic absorption spectrometry with the results consistently, which is suitable for the determination of platinum in waste platinum-loaded carbon catalyst samples.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Vienna, John D.; Schweiger, Michael J.; Bonham, Charles C.
Roughly half of the projected Hanford high-level waste batches will have waste loadings limited by relatively high concentration of Al2O3. Individual glasses have been formulated and tested to demonstrate that it is possible to increase the loading of these high-Al2O3 wastes in glass by as much as 50%. To implement such increases in waste loading in the Hanford Tank Waste Treatment and Immobilization Plant, the impact of composition on the properties of high-Al2O3 waste glasses must be quantified in the form of validated glass property-composition models. To collect the data necessary for glass property-composition models, a multi-phase experimental approach wasmore » developed. In the first phase of the study, a set of 46 glass compositions were statistically designed to most efficiently backfill existing data in the composition region for high-Al2O3 (15 to 30 wt%) waste glasses. The glasses were fabricated and key glass properties were tested: •Product Consistency Test (PCT) on quench (Q) and canister centerline cooled (CCC) samples •Toxicity Characteristic Leaching Procedure (TCLP) on Q and CCC samples •Crystallinity as a function of temperature (T) at equilibrium and of CCC samples •Viscosity and electrical conductivity as a function of T The measured properties of these glasses were compared to predictions from previously existing models developed over lower Al2O3 concentration ranges. Areas requiring additional testing and modeling were highlighted.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Weaver, Phyllis C.
2013-12-12
The U.S. Department of Energy (DOE) Oak Ridge Office of Environmental Management (EM-OR) requested Oak Ridge Associated Universities (ORAU), working under the Oak Ridge Institute for Science and Education (ORISE) contract, to provide technical and independent waste management planning support under the American Recovery and Reinvestment Act (ARRA). Specifically, DOE EM-OR requested ORAU to plan and implement a sampling and analysis campaign to target certain items associated with URS|CH2M Oak Ridge, LLC (UCOR) surveillance and maintenance (S&M) process inventory waste. Eight populations of historical and reoccurring S&M waste at the Oak Ridge National Laboratory (ORNL) have been identified in themore » Waste Handling Plan for Surveillance and Maintenance Activities at the Oak Ridge National Laboratory, DOE/OR/01-2565&D2 (WHP) (DOE 2012) for evaluation and processing for final disposal. This waste was generated during processing, surveillance, and maintenance activities associated with the facilities identified in the process knowledge (PK) provided in Appendix A. A list of items for sampling and analysis were generated from a subset of materials identified in the WHP populations (POPs) 4, 5, 6, 7, and 8, plus a small number of items not explicitly addressed by the WHP. Specifically, UCOR S&M project personnel identified 62 miscellaneous waste items that would require some level of evaluation to identify the appropriate pathway for disposal. These items are highly diverse, relative to origin; composition; physical description; contamination level; data requirements; and the presumed treatment, storage, and disposal facility (TSDF). Because of this diversity, ORAU developed a structured approach to address item-specific data requirements necessary for acceptance in a presumed TSDF that includes the Environmental Management Waste Management Facility (EMWMF)—using the approved Waste Lot (WL) 108.1 profile—the Y-12 Sanitary Landfill (SLF) if appropriate; EnergySolutions Clive; and the Nevada National Security Site (NNSS) (ORAU 2013b). Finally, the evaluation of these wastes was more suited to a judgmental sampling approach rather than a statistical design, meaning data were collected for each individual item, thereby providing information for item-byitem disposition decisions. ORAU prepared a sampling and analysis plan (SAP) that outlined data collection strategies, methodologies, and analytical guidelines and requirements necessary for characterizing targeted items (ORAU 2013b). The SAP described an approach to collect samples that allowed evaluation as to whether or not the waste would be eligible for disposal at the EMWMF. If the waste was determined not to be eligible for EMWMF disposal, then there would be adequate information collected that would allow the waste to be profiled for one of the alternate TSDFs listed above.« less
Collection of domestic waste. Review of occupational health problems and their possible causes.
Poulsen, O M; Breum, N O; Ebbehøj, N; Hansen, A M; Ivens, U I; van Lelieveld, D; Malmros, P; Matthiasen, L; Nielsen, B H; Nielsen, E M
1995-08-18
During the last decade, a growing interest in recycling of domestic waste has emerged, and action plans to increase the recycling of domestic waste have been agreed by many governments. A common feature of these plans is the implementation of new systems and equipment for the collection of domestic waste which has been separated at source. However, only limited information exists on possible occupational health problems related to such new systems. Occupational accidents are very frequent among waste collectors. Based on current knowledge, it appears that the risk factors should be considered as an integrated entity, i.e. technical factors (poor accessibility to the waste, design of equipment) may act in concert with high working rate, visual fatigue due to poor illumination and perhaps muscle fatigue due to high work load. Musculoskeletal problems are also common among waste collectors. A good deal of knowledge has accumulated on mechanical load on the spine and energetic load on the cardio-pulmonary system in relation to the handling of waste bags, bins, domestic containers and large containers. However, epidemiologic studies with exposure classification based on field measurement are needed, both to further identify high risk work conditions and to provide a detailed basis for the establishment of occupational exposure limits for mechanical and energetic load particularly in relation to pulling, pushing and tilting of containers. In 1975, an excess risk for chronic bronchitis was reported for waste collectors in Geneva (Rufèner-Press et al., 1975) and data from the Danish Registry of Occupational Accidents and Diseases also indicate an excess risk for pulmonary problems among waste collectors compared with the total work force. Surprisingly few measurements of potentially hazardous airborne exposures have been performed, and the causality of work-related pulmonary problems among waste collectors is unknown. Recent studies have indicated that implementation of some new waste collection systems may result in an increased risk of occupational health problems. High incidence rates of gastrointestinal problems, irritation of the eye and skin, and perhaps symptoms of organic dust toxic syndrome (influenza-like symptoms, cough, muscle pains, fever, fatigue, headache) have been reported among workers collecting the biodegradable fraction of domestic waste. The few data available on exposure to bio-aerosols and volatile compounds have indicated that these waste collectors may be simultaneously exposed to multiple agents such as dust containing bacteria, endotoxin, mould spores, glucans, volatile organic compounds, and diesel exhaust. Several studies have reported similar health problems as well as high incidence rates of pulmonary disease among workers at plants recycling domestic waste.(ABSTRACT TRUNCATED AT 400 WORDS)
40 CFR 60.59b - Reporting and recordkeeping requirements.
Code of Federal Regulations, 2012 CFR
2012-07-01
... Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994 or for Which... the owner or operator plans to combust in the affected facility. (4) The municipal waste combustor..., municipal waste combustor unit load measurements, and particulate matter control device inlet temperatures...
40 CFR 60.59b - Reporting and recordkeeping requirements.
Code of Federal Regulations, 2013 CFR
2013-07-01
... Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994 or for Which... the owner or operator plans to combust in the affected facility. (4) The municipal waste combustor..., municipal waste combustor unit load measurements, and particulate matter control device inlet temperatures...
40 CFR 60.59b - Reporting and recordkeeping requirements.
Code of Federal Regulations, 2014 CFR
2014-07-01
... Municipal Waste Combustors for Which Construction is Commenced After September 20, 1994 or for Which... the owner or operator plans to combust in the affected facility. (4) The municipal waste combustor..., municipal waste combustor unit load measurements, and particulate matter control device inlet temperatures...
Gough, Heidi L; Nelsen, Diane; Muller, Christopher; Ferguson, John
2013-02-01
Recent interest in carbon-neutral biofuels has revived interest in co-digestion for methane generation. At wastewater treatment facilities, organic wastes may be co-digested with sludge using established anaerobic digesters. However, changes to organic loadings may induce digester instability, particularly for thermophilic digesters. To examine this problem, thermophilic (55 degrees C) co-digestion was studied for two food-industry wastes in semi-continuous laboratory digesters; in addition, the wastes' biochemical methane potentials were tested. Wastes with high chemical oxygen demand (COD) content were selected as feedstocks allowing increased input of potential energy to reactors without substantially altering volumetric loadings. Methane generation increased while reactor pH and volatile solids remained stable. Lag periods observed prior to methane stimulation suggested that acclimation of the microbial community may be critical to performance during co-digestion. Chemical oxygen demand mass balances in the experimental and control reactors indicated that all of the food industry waste COD was converted to methane.
VITRIFICATION SYSTEM FOR THE TREATMENT OF PLUTONIUM-BEARING WASTE AT LOS ALAMOS NATIONAL LABORATORY
DOE Office of Scientific and Technical Information (OSTI.GOV)
R. NAKAOKA; G. VEAZEY; ET AL
2001-05-01
A glove box vitrification system is being fabricated to process aqueous evaporator bottom waste generated at the Plutonium Facility (TA-55) at Los Alamos National Laboratory (LANL). The system will be the first within the U.S. Department of Energy Complex to routinely convert Pu{sup 239}-bearing transuranic (TRU) waste to a glass matrix for eventual disposal at the Waste Isolation Pilot Plant (WIPP). Currently at LANL, this waste is solidified in Portland cement. Radionuclide loading in the cementation process is restricted by potential radiolytic degradation (expressed as a wattage limit), which has been imposed to prevent the accumulation of flammable concentrations ofmore » H{sub 2} within waste packages. Waste matrixes with a higher water content (e.g., cement) are assigned a lower permissible wattage limit to compensate for their potential higher generation of H{sub 2}. This significantly increases the number of waste packages that must be prepared and shipped, thus driving up the costs of waste handling and disposal. The glove box vitrification system that is under construction will address this limitation. Because the resultant glass matrix produced by the vitrification process is non-hydrogenous, no H{sub 2} can be radiolytically evolved, and drums could be loaded to the maximum allowable limit of 40 watts. In effect, the glass waste form shifts the limiting constraint for loading disposal drums from wattage to the criticality limit of 200 fissile gram equivalents, thus significantly reducing the number of drums generated from this waste stream. It is anticipated that the number of drums generated from treatment of evaporator bottoms will be reduced by a factor of 4 annually when the vitrification system is operational. The system is currently undergoing non-radioactive operability testing, and will be fully operational in the year 2003.« less
Scaling behavior of fully spin-coated TFT
NASA Astrophysics Data System (ADS)
Mondal, Sandip; Kumar, Arvind; Rao, K. S. R. Koteswara; Venkataraman, V.
2017-05-01
We studied channel scaling behavior of fully spin coated, low temperature solution processed thin film transistor (TFT) fabricated on p++ - Si (˜1021 cm-3) as bottom gate. The solution processed, spin coated 40 nm thick amorphous Indium Gallium Zinc Oxide (a-IGZO) and 50 nm thick amorphous zirconium di-oxide (a-ZrO2) has been used as channel and low leakage dielectric at 350°C respectively. The channel scaling effect of the TFT with different width/length ratio (W/L= 2.5, 5 and 15) for same channel length (L = 10 μm) has been demonstrated. The lowest threshold voltage (Vth) is 6.25 V for the W/L=50/10. The maximum field effect mobility (μFE) has been found to be 0.123 cm2/Vs from W/L of 50/10 with the drain to source voltage (VD) of 10V and 20V gate to source voltage (VG). We also demonstrated that there is no contact resistance effect on the mobility of the fully sol-gel spin coated TFT.
Projection Effects of Large-scale Structures on Weak-lensing Peak Abundances
NASA Astrophysics Data System (ADS)
Yuan, Shuo; Liu, Xiangkun; Pan, Chuzhong; Wang, Qiao; Fan, Zuhui
2018-04-01
High peaks in weak lensing (WL) maps originate dominantly from the lensing effects of single massive halos. Their abundance is therefore closely related to the halo mass function and thus a powerful cosmological probe. However, besides individual massive halos, large-scale structures (LSS) along lines of sight also contribute to the peak signals. In this paper, with ray-tracing simulations, we investigate the LSS projection effects. We show that for current surveys with a large shape noise, the stochastic LSS effects are subdominant. For future WL surveys with source galaxies having a median redshift z med ∼ 1 or higher, however, they are significant. For the cosmological constraints derived from observed WL high-peak counts, severe biases can occur if the LSS effects are not taken into account properly. We extend the model of Fan et al. by incorporating the LSS projection effects into the theoretical considerations. By comparing with simulation results, we demonstrate the good performance of the improved model and its applicability in cosmological studies.
Corrosion Behavior of Cast Iron in Freely Aerated Stagnant Arabian Gulf Seawater
Sherif, El-Sayed M.; Abdo, Hany S.; Almajid, Abdulhakim A.
2015-01-01
In this work, the results obtained from studying the corrosion of cast iron in freely aerated stagnant Arabian Gulf seawater (AGS) at room temperature were reported. The study was carried out using weight-loss (WL), cyclic potentiodynamic polarization (CPP), open-circuit potential (OCP), and electrochemical impedance spectroscopy (EIS) measurements and complemented by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) investigations. WL experiments between two and 10 days’ immersion in the test electrolyte indicated that the weight-loss the cast iron increases with increasing the time of immersion. CPP measurements after 1 h and 24 h exposure period showed that the increase of time decreases the corrosion via decreasing the anodic and cathodic currents, as well as decreasing the corrosion current and corrosion rate and increasing the polarization resistance of the cast iron. EIS data confirmed the ones obtained by WL and CPP that the increase of immersion time decreases the corrosion of cast iron by increasing its polarization resistance.
HLW Melter Control Strategy Without Visual Feedback VSL-12R2500-1 Rev 0
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, A A.; Joseph, Innocent; Matlack, Keith S.
2012-11-13
Plans for the treatment of high level waste (HL W) at the Hanford Tank Waste Treatment and Immobilization Plant (WTP) are based upon the inventory of the tank wastes, the anticipated performance of the pretreatment processes, and current understanding of the capability of the borosilicate glass waste form [I]. The WTP HLW melter design, unlike earlier DOE melter designs, incorporates an active glass bubbler system. The bubblers create active glass pool convection and thereby improve heat and mass transfer and increase glass melting rates. The WTP HLW melter has a glass surface area of 3.75 m{sup 2} and depth ofmore » ~ 1.1 m. The two melters in the HLW facility together are designed to produce up to 7.5 MT of glass per day at 100% availability. Further increases in HL W waste processing rates can potentially be achieved by increasing the melter operating temperature above 1150°C and by increasing the waste loading in the glass product. Increasing the waste loading also has the added benefit of decreasing the number of canisters for storage.« less
Pie waste - A component of food waste and a renewable substrate for producing ethanol.
Magyar, Margaret; da Costa Sousa, Leonardo; Jayanthi, Singaram; Balan, Venkatesh
2017-04-01
Sugar-rich food waste is a sustainable feedstock that can be converted into ethanol without an expensive thermochemical pretreatment that is commonly used in first and second generation processes. In this manuscript we have outlined the pie waste conversion to ethanol through a two-step process, namely, enzyme hydrolysis using commercial enzyme products mixtures and microbial fermentation using yeast. Optimized enzyme cocktail was found to be 45% alpha amylase, 45% gamma amylase, and 10% pectinase at 2.5mg enzyme protein/g glucan produced a hydrolysate with high glucose concentration. All three solid loadings (20%, 30%, and 40%) produced sugar-rich hydrolysates and ethanol with little to no enzyme or yeast inhibition. Enzymatic hydrolysis and fermentation process mass balance was carried out using pie waste on a 1000g dry weight basis that produced 329g ethanol at 20% solids loading. This process clearly demonstrate how food waste could be efficiently converted to ethanol that could be used for making biodiesel by reacting with waste cooking oil. Copyright © 2017 Elsevier Ltd. All rights reserved.
Technical Status Report: Preliminary Glass Formulation Report for INEEL HAW. Revision 1
DOE Office of Scientific and Technical Information (OSTI.GOV)
Peeler, D.; Reamer, I.; Vienna, J.
1998-03-01
Preliminary glass formulation work has been initiated at Pacific Northwest National Laboratory (PNNL) and the Savannah River Technology Center (SRTC) to support immobilization efforts of Idaho National Engineering and Environmental Laboratory (INEEL) high activity waste (HAW). Based on current pretreatment flow sheet assumptions, several glasses were fabricated and tested using an average `All Blend` waste stream composition which is dominated by the presence of ZrO{sub 2} (i.e., approximately 80 wt percent). The results of this initial work show that immobilization via vitrification is a viable option for a specific INEEL HAW waste stream. Waste loadings of at least 19 wtmore » percent can be achieved for the `All Blend` stream while maintaining targeted processing and product performance criteria. This waste loading translates into a ZrO{sub 2} content in excess of 15 wt percent in the final glass waste form. Frits developed for this work are based in the alkali borosilicate system. Although the results indicate that vitrification can be used to immobilize the `All Blend` waste stream, the glass compositions are by no means optimized.« less
A Characteristics-Based Approach to Radioactive Waste Classification in Advanced Nuclear Fuel Cycles
NASA Astrophysics Data System (ADS)
Djokic, Denia
The radioactive waste classification system currently used in the United States primarily relies on a source-based framework. This has lead to numerous issues, such as wastes that are not categorized by their intrinsic risk, or wastes that do not fall under a category within the framework and therefore are without a legal imperative for responsible management. Furthermore, in the possible case that advanced fuel cycles were to be deployed in the United States, the shortcomings of the source-based classification system would be exacerbated: advanced fuel cycles implement processes such as the separation of used nuclear fuel, which introduce new waste streams of varying characteristics. To be able to manage and dispose of these potential new wastes properly, development of a classification system that would assign appropriate level of management to each type of waste based on its physical properties is imperative. This dissertation explores how characteristics from wastes generated from potential future nuclear fuel cycles could be coupled with a characteristics-based classification framework. A static mass flow model developed under the Department of Energy's Fuel Cycle Research & Development program, called the Fuel-cycle Integration and Tradeoffs (FIT) model, was used to calculate the composition of waste streams resulting from different nuclear fuel cycle choices: two modified open fuel cycle cases (recycle in MOX reactor) and two different continuous-recycle fast reactor recycle cases (oxide and metal fuel fast reactors). This analysis focuses on the impact of waste heat load on waste classification practices, although future work could involve coupling waste heat load with metrics of radiotoxicity and longevity. The value of separation of heat-generating fission products and actinides in different fuel cycles and how it could inform long- and short-term disposal management is discussed. It is shown that the benefits of reducing the short-term fission-product heat load of waste destined for geologic disposal are neglected under the current source-based radioactive waste classification system, and that it is useful to classify waste streams based on how favorable the impact of interim storage is on increasing repository capacity. The need for a more diverse set of waste classes is discussed, and it is shown that the characteristics-based IAEA classification guidelines could accommodate wastes created from advanced fuel cycles more comprehensively than the U.S. classification framework.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Edwards, T.
2010-10-07
The Defense Waste Processing Facility (DWPF), which is operated by Savannah River Remediation, LLC (SRR), has recently begun processing Sludge Batch 6 (SB6) by combining it with Frit 418 at a nominal waste loading (WL) of 36%. A unique feature of the SB6/Frit 418 glass system, as compared to the previous glass systems processed in DWPF, is that thorium will be a reportable element (i.e., concentrations of elemental thorium in the final glass product greater than 0.5 weight percent (wt%)) for the resulting wasteform. Several activities were initiated based upon this unique aspect of SB6. One of these was anmore » investigation into the impact of thorium on the models utilized in DWPF's Product Composition and Control System (PCCS). While the PCCS is described in more detail below, for now note that it is utilized by Waste Solidification Engineering (WSE) to evaluate the acceptability of each batch of material in the Slurry Mix Evaporator (SME) before this material is passed on to the melter. The evaluation employs models that predict properties associated with processability and product quality from the composition of vitrified samples of the SME material. The investigation of the impact of thorium on these models was conducted by Peeler and Edwards [1] and led to a recommendation that DWPF can process the SB6/Frit 418 glass system with ThO{sub 2} concentrations up to 1.8 wt% in glass. Questions also arose regarding the handling of thorium in the SME batch acceptability process as documented by Brown, Postles, and Edwards [2]. Specifically, that document is the technical bases of PCCS, and while Peeler and Edwards confirmed the reliability of the models, there is a need to confirm that the current implementation of DWPF's PCCS appropriately handles thorium as a reportable element. Realization of this need led to a Technical Task Request (TTR) prepared by Bricker [3] that identified some specific SME-related activities that the Savannah River National Laboratory (SRNL) was requested to conduct. SRNL issued a Task Technical and Quality Assurance (TT&QA) plan [4] in response to the SRR request. The conclusions provided in this report are that no changes need to be made to the SME acceptability process (i.e., no modifications to WSRC-TR-95-00364, Revision 5, are needed) and no changes need to be made to the Product Composition Control System (PCCS) itself (i.e. the spreadsheet utilized by Waste Solidification Engineering (WSE) for acceptability decisions does not require modification) in response to thorium becoming a reportable element for DWPF operations. In addition, the inputs and results for the two test cases requested by WSE for use in confirming the successful activation of thorium as a reportable element for DWPF operations during the processing of SB6 are presented in this report.« less
NASA Astrophysics Data System (ADS)
Shi, Yuan Yuan; Yan, Wei Yu; Huang, Zachary Y.; Wang, Zi Long; Wu, Xiao Bo; Zeng, Zhi Jiang
2013-02-01
The honey bee is a social insect characterized by caste differentiation, by which a young larva can develop into either a queen or a worker. Despite possessing the same genome, queen and workers display marked differences in reproductive capacity, physiology, and behavior. Recent studies have shown that DNA methylation plays important roles in caste differentiation. To further explore the roles of DNA methylation in this process, we analyzed DNA methylome profiles of both queen larvae (QL) and worker larvae (WL) of different ages (2, 4, and 6 day old), by using methylated DNA immunoprecipitation-sequencing (meDIP-seq) technique. The global DNA methylation levels varied between the larvae of two castes. DNA methylation increased from 2-day- to 4-day-old QL and then decreased in 6-day-old larvae. In WL, methylation levels increased with age. The methylcytosines in both larvae were enriched in introns, followed by coding sequence (CDS) regions, CpG islands, 2 kbp downstream and upstream of genes, and 5' and 3' untranslated regions (UTRs). The number of differentially methylated genes (DMGs) in 2-, 4-, and 6-day-old QL and WL was 725, 3,013, and 5,049, respectively. Compared to 4- and 6-day-old WL, a large number of genes in QL were downmethylated, which were involved in many processes including development, reproduction, and metabolic regulation. In addition, some DMGs were concerned with caste differentiation.
Discrimination of wild-growing and cultivated Lentinus edodes by tri-step infrared spectroscopy
NASA Astrophysics Data System (ADS)
Lin, Haojian; Liu, Gang; Yang, Weimei; An, Ran; Ou, Quanhong
2018-01-01
It's not easy to discriminate dried wild-growing Lentinus edodes (WL) and cultivated Lentinus edodes (CL) by conventional method based on the morphological inspection of fruiting bodies. In this paper, fruiting body samples of WL and CL are discriminated by a tri-step IR spectroscopy method, including Fourier transform infrared (FT-IR) spectroscopy, second derivatives infrared (SD-IR) spectroscopy and two-dimensional correlation infrared (2D-IR) spectroscopy under thermal perturbation. The results show that the FT-IR spectra of WL and CL are similar in holistic spectral profile. More significant differences are exhibited in their SD-IR spectra in the range of 1700 - 900 cm-1. Furthermore, more evident differences have been observed in their synchronous 2D-IR spectra in the range of 2970 - 2900, 1678 - 1390, 1250 -1104 and 1090 - 1030 cm-1. The CL has thirteen auto-peaks at 2958, 2921, 1649, 1563, 1450, 1218, 1192, 1161, 1140, 1110, 1082, 1065 and 1047 cm-1, in which the four strongest auto-peaks are at 2921, 1563, 1192 and 1082 cm-1. The WL shows fifteen auto-peaks at 2960, 2937, 2921, 1650, 1615, 1555, 1458, 1219, 1190, 1138, 1111, 1084, 1068, 1048 and 1033 cm-1, in which the four strongest auto-peaks are at 2921, 1650, 1190 and 1068 cm-1. This study shows the potential of FT-IR spectroscopy and 2D correlation analysis in a simple and quick distinction of wild-growing and cultivated mushrooms.
Sørensen, Thorkild I A; Boutin, Philippe; Taylor, Moira A; Larsen, Lesli H; Verdich, Camilla; Petersen, Liselotte; Holst, Claus; Echwald, Søren M; Dina, Christian; Toubro, Søren; Petersen, Martin; Polak, Jan; Clément, Karine; Martínez, J Alfredo; Langin, Dominique; Oppert, Jean-Michel; Stich, Vladimir; Macdonald, Ian; Arner, Peter; Saris, Wim H M; Pedersen, Oluf; Astrup, Arne; Froguel, Philippe
2006-06-01
To study if genes with common single nucleotide polymorphisms (SNPs) associated with obesity-related phenotypes influence weight loss (WL) in obese individuals treated by a hypo-energetic low-fat or high-fat diet. Randomised, parallel, two-arm, open-label multi-centre trial. Eight clinical centres in seven European countries. 771 obese adult individuals. 10-wk dietary intervention to hypo-energetic (-600 kcal/d) diets with a targeted fat energy of 20%-25% or 40%-45%, completed in 648 participants. WL during the 10 wk in relation to genotypes of 42 SNPs in 26 candidate genes, probably associated with hypothalamic regulation of appetite, efficiency of energy expenditure, regulation of adipocyte differentiation and function, lipid and glucose metabolism, or production of adipocytokines, determined in 642 participants. Compared with the noncarriers of each of the SNPs, and after adjusting for gender, age, baseline weight and centre, heterozygotes showed WL differences that ranged from -0.6 to 0.8 kg, and homozygotes, from -0.7 to 3.1 kg. Genotype-dependent additional WL on low-fat diet ranged from 1.9 to -1.6 kg in heterozygotes, and from 3.8 kg to -2.1 kg in homozygotes relative to the noncarriers. Considering the multiple testing conducted, none of the associations was statistically significant. Polymorphisms in a panel of obesity-related candidate genes play a minor role, if any, in modulating weight changes induced by a moderate hypo-energetic low-fat or high-fat diet.
Fernández, María Soledad; Martínez, Mariela Florencia; Pérez, Adriana Alicia; Santini, María Soledad; Gould, Ignacio Tomás; Salomón, Oscar Daniel
2015-12-01
The performance of two light-emitting diode traps with white and black light for capturing phlebotomine sand flies, developed by the Argentinean Leishmaniasis Research Network (REDILA-WL and REDILA-BL traps), were compared with the traditional CDC incandescent light trap. Entomological data were obtained from six sand fly surveys conducted in Argentina in different environments. Data analyses were conducted for the presence and the abundance of Lutzomyia longipalpis, Migonemyia migonei, and Nyssomyia whitmani (106 sites). No differences were found in presence/absence among the three types of traps for all sand fly species (p>0.05). The collection mean of Lu. longipalpis from the REDILA-BL didn´t differ from the CDC trap means, nor were differences seen between the REDILA-WL and the CDC trap collection means (p>0.05), but collections were larger from the REDILA-BL trap compared to the REDILA-WL trap (p<0.05). For Mg. migonei and Ny. whitmani, no differences were found among the three types of traps in the number of individuals captured (p>0.05). These results suggest that both REDILA traps could be used as an alternative capture tool to the original CDC trap for surveillance of these species, and that the REDILA-BL will also allow a comparable estimation of the abundance of these flies to the CDC light trap captures. In addition, the REDILA-BL has better performance than the REDILA-WL, at least for Lu. longipalpis. © 2015 The Society for Vector Ecology.
NASA Astrophysics Data System (ADS)
Lee, Kyoung-Sun; Imada, Shinsuke; Watanabe, Kyoko; Bamba, Yumi; Brooks, David
2017-08-01
An X1.6 flare on 2014 October 22 was observed by multiple spectrometers in UV, EUV and X-ray (Hinode/EIS, IRIS, and RHESSI), and multi-wavelength imaging observations (SDO/AIA and HMI). We analyze a bright kernel that produces a white light (WL) flare with continuum enhancement and a hard X-ray (HXR) peak. Taking advantage of the spectroscopic observations of IRIS and Hinode/EIS, we measure the temporal variation of the plasma properties in the bright kernel in the chromosphere and corona. We find that explosive evaporation was observed when the WL emission occurred. The temporal correlation of the WL emission, HXR peak, and evaporation flows indicates that the WL emission was produced by accelerated electrons. We calculated the energy flux deposited by non-thermal electrons (observed by RHESSI) and compared it to the dissipated energy estimated from a chromospheric line (Mg II triplet) observed by IRIS. The deposited energy flux from the non-thermal electrons is about (3-7.7)x1010 erg cm-2 s-1 for a given low-energy cutoff of 30-40 keV, assuming the thick-target model. The energy flux estimated from the changes in temperature in the chromosphere measured using the Mg II subordinate line is about (4.6-6.7)×109 erg cm-2 s-1: ˜6%-22% of the deposited energy. This comparison of estimated energy fluxes implies that the continuum enhancement was directly produced by the non-thermal electrons.
Active Sites Environmental Monitoring Program: Mid-FY 1991 report
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ashwood, T.L.; Wickliff, D.S.; Morrissey, C.M.
1991-10-01
This report summarizes the activities of the Active Sites Environmental Monitoring Program (ASEMP) from October 1990 through March 1991. The ASEMP was established in 1989 by Solid Waste Operations and the Environmental Sciences Division to provide early detection and performance monitoring at active low-level radioactive waste (LLW) disposal sites in Solid Waste Storage Area (SWSA) 6 and transuranic (TRU) waste storage sites in SWSA 5 as required by chapters II and III of US Department of Energy Order 5820.2A. Monitoring results continue to demonstrate the no LLW is being leached from the storage vaults on the tumulus pads. Loading ofmore » vaults on Tumulus II began during this reporting period and 115 vaults had been loaded by the end of March 1991.« less
Gou, Chengliu; Yang, Zhaohui; Huang, Jing; Wang, Huiling; Xu, Haiyin; Wang, Like
2014-06-01
Anaerobic co-digestion of waste activated sludge and food waste was investigated semi-continuously using continuously stirred tank reactors. Results showed that the performance of co-digestion system was distinctly influenced by temperature and organic loading rate (OLR) in terms of gas production rate (GPR), methane yield, volatile solids (VS) removal efficiency and the system stability. The highest GPR at 55 °C was 1.6 and 1.3 times higher than that at 35 and 45 °C with the OLR of 1 g VSL(-1)d(-1), and the corresponding average CH₄ yields were 0.40, 0.26 and 0.30 L CH₄ g(-1)VSadded, respectively. The thermophilic system exhibited the best load bearing capacity at extremely high OLR of 7 g VSL(-1)d(-1), while the mesophilic system showed the best process stability at low OLRs (< 5 g VSL(-1)d(-1)). Temperature had a more remarkable effect on the richness and diversity of microbial populations than the OLR. Copyright © 2014 Elsevier Ltd. All rights reserved.
Bales, Connie W; Porter Starr, Kathryn N; Orenduff, Melissa C; McDonald, Shelley R; Molnar, Karen; Jarman, Aubrey K; Onyenwoke, Ann; Mulder, Hillary; Payne, Martha E; Pieper, Carl F
2017-05-01
Women have higher rates of obesity than men and develop more pronounced functional deficits as a result. Yet, little is known about how obesity reduction affects their functional status, including whether their responses differ when protein intake is enhanced. The aim of this study was to confirm the feasibility of delivery of a higher-protein (balanced at each meal) calorie-restricted diet in obese women and determine its efficacy for influencing function and retention of lean mass. Obese community-dwelling women [ n = 80; body mass index (in kg/m 2 ), in means ± SDs: 37.8 ± 5.9; aged 45-78 y; 58.8% white] were enrolled in a weight-loss (-500 kcal/d) study and randomly assigned to either a Control-Weight-Loss (C-WL; 0.8 g protein/kg body weight) group or a High-Protein-Weight-Loss (HP-WL; 1.2 g protein/kg body weight; 30 g protein 3 times/d) group in a 1:2 allocation. Primary outcomes were function by 6-min walk test (6MWT) and lean mass by using the BodPod (Life Measurement, Inc.) at 0, 4, and 6 mo. Both groups reduced calorie intakes and body weights ( P < 0.001), and the feasibility of the HP-WL intervention was confirmed. The 6MWT results improved ( P < 0.01) at 4 mo in the HP-WL group and at 6 mo in both groups ( P < 0.001). Both groups improved function by several other measures while slightly decreasing ( P < 0.01) lean mass (-1.0 kg, C-WL; -0.6 kg, HP-WL). Weight loss was greater in white than in black women at both 4 mo (6.0 ± 3.6 compared with 3.7 ± 3.4 kg; P < 0.02) and 6 mo (7.2 ± 4.8 compared with 4.0 ± 4.7 kg; P < 0.04) and tended to be positively related to age ( P < 0.06). A clinically important functional benefit of obesity reduction was confirmed in both study groups, with no significant group effect. Our findings of racial differences in response to the intervention and a potential influence of participant age lend support for further studies sufficiently powered to explore the interaction of race and age with functional responses to obesity reduction in women. This trial was registered at clinicaltrials.gov as NCT02033655.
NASA Astrophysics Data System (ADS)
Hossain, M. A.; Anderson, E. R.; Bhuiyan, M. A.; Hossain, F.; Shah-Newaz, S. M.
2014-12-01
Bangladesh is the lowest riparian of the huge system of the Ganges, Brahmaputra and Meghna (GBM) basins, second to that of Amazan, with 1.75 million sq-km catchment area, only 7% is inside Bangladesh. High inflow from GBM associated with the intense rainfall is the source of flood in Bangladesh. Flood Forecasting and Early Warning (FFEW) is the mandate and responsibility of Bangladesh Water Development Board (BWDB) and Flood Forecasting and Warning Center (FFWC) under BWDB has been carrying out this responsibility since 1972 and operational on 7-days a week during monsoon (May to October). FFEW system started with few hours lead time has been upgraded up to to 5-days with reasonable accuracy. At FFWC numerical Hydrodynamic model is used for generating water level (WL) forecast upto 5-days at 54 points on 29 rivers based on real-time observed WL of 83 and rainfall of 56 stations with boundary estimationa on daily basis. Main challenge of this system is the boundary estimation is the limited upstream data of the transboundary rivers, obstacle for increasing lead-time for FFEW. The satellite based upper catchment data may overcome this limitation. Recent NASA-French joint Satellite mission JASON-2 records Water Elevation (WE) and it may be used within 24 hours. Using JASON-2 recorded WE data of 4 and 3 virtual stations on the Ganges and Brahmaputra rivers , respectively (upper catchment), a new methodology has been developed for increasing lead time of forecast. Correlation between the JASON-2 recorded WE on the virtual stations at the upper catchment and WL of 2 dominating boundary stations at model boundary on the Ganges and Brahmaputra has been derived for generating WL forecast at those 2 boundary stations, which used as input in model. FFWC has started experimental 8-days lead-time WL forecast at 09 stations (5 in Brahmaputra and 4 in Ganges) using generated boundary data and regularly updating the results in the website. The trend of the forecasted WL using JASON-2 data is similar to those upto 5-days forecast generated in the existing system. This is a new approach in FFEW in Bangladesh where boundary estimation becomes possible using JASON-2 observed WE data of the Transboundary rivers. There is scope of further development of this system along with increase of lead time. Reference: www.ffwc.gov.bd
DOE Office of Scientific and Technical Information (OSTI.GOV)
Bowers, Geoffrey M.; Schaef, H. Todd; Loring, John S.
This paper explores the molecular-scale interactions between CO 2 and the representative smectite mineral hectorite under supercritical conditions (90 bar, 50°C) using novel in situ X-ray diffraction (XRD), infrared (IR) spectroscopy, and magic angle spinning (MAS) nuclear magnetic resonance (NMR) techniques. Particular emphasis is placed on understanding the roles of the smectite charge balancing cation (CBC) and H O in these interactions. The data show that supercritical CO 2 (scCO 2) can be adsorbed on external surfaces and in the confined interlayer spaces of hectorite at 50°C and 90 bar, with the uptake of CO 2 into the interlayer favoredmore » at low H 2O content and when the basal spacing is similar to a monolayer hydrate of hectorite (1WL, ~12.5 Å). These results are in agreement with published spectroscopic and molecular modeling data for the related smectite Na-montmorillonite.Charge balancing cations with small radii, large hydration energies, and low polarizabilities tend to scavenge H 2O from humid scCO 2 or retain the H 2O they held before scCO 2 exposure, swelling spontaneously to a bilayer hydrate (2WL) dominated state that largely prevents CO 2-ion interactions and influences the extent of CO 2 intercalation into the interlayer. In contrast, ions with large radii, low hydration energies, and large polarizabilities more readily form close associations with CO 2 with the energetics enabling coexistence of CO 2 and H2O in the interlayer over a wide range of scCO 2 humidities. Integrating our results with those from molecular dynamics simulations of wet CO 2-bearing montmorillonites suggest that adsorbed CO 2 in 1WL-type interlayers is oriented with its long axis parallel to the clay sheets and experiences dynamics dominated by anisotropic rotation about the axis perpendicular to the CO 2 long axis at rates of at least ~105 Hz. If appreciable CO 2 is adsorbed in 2WL-type interlayers, it must experience a mean orientation and dynamic averaging affects that mimic the 1WL-type adsorption environment. External surface adsorbed CO 2 is dynamically similar to the 1WL case, but the CO 2 long axis samples a larger range of orientations with respect to the smectite surface and adopts a different mean angle between the long axis and the smectite surface. Our data also suggest that equilibrating hectorite with a largevolume of scCO 2 at 50°C and 90 bar leads to interlayer dehydration, with the extent of dehydration correlating with the hydrophilicity of the CBC.« less
Use of cationic polymers to reduce pathogen levels during dairy manure separation.
Liu, Zong; Carroll, Zachary S; Long, Sharon C; Gunasekaran, Sundaram; Runge, Troy
2016-01-15
Various separation technologies are used to deal with the enormous amounts of animal waste that large livestock operations generate. When the recycled waste stream is land applied, it is essential to lower the pathogen load to safeguard the health of livestock and humans. We investigated whether cationic polymers, used as a flocculent in the solid/liquid separation process, could reduce the pathogen indicator load in the animal waste stream. The effects of low charge density cationic polyacrylamide (CPAM) and high charge density cationic polydicyandiamide (PDCD) were investigated. Results demonstrated that CPAM was more effective than PDCD for manure coagulation and flocculation, while PDCD was more effective than CPAM in reducing the pathogen indicator loads. However, their combined use, CPAM followed by PDCD, resulted in both improved solids separation and pathogen indicator reduction. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.
Equilibrium Temperature Profiles within Fission Product Waste Forms
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kaminski, Michael D.
2016-10-01
We studied waste form strategies for advanced fuel cycle schemes. Several options were considered for three waste streams with the following fission products: cesium and strontium, transition metals, and lanthanides. These three waste streams may be combined or disposed separately. The decay of several isotopes will generate heat that must be accommodated by the waste form, and this heat will affect the waste loadings. To help make an informed decision on the best option, we present computational data on the equilibrium temperature of glass waste forms containing a combination of these three streams.
Resch, C; Grasmug, M; Smeets, W; Braun, R; Kirchmayr, R
2006-01-01
Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.
Effects of concentrated leachate injection modes on stabilization of landfilled waste.
He, Ruo; Wei, Xiao-Meng; Chen, Min; Su, Yao; Tian, Bao-Hu
2016-02-01
Injection of concentrated leachate to landfills is a simple and cost-effective technology for concentrated leachate treatment. In this study, the effects of injection mode of concentrated leachate and its hydraulic loading rate on the stabilization of landfilled waste were investigated. Compared with the injection of concentrated leachate, the joint injection of leachate and concentrated leachate (1:1, v/v) was more beneficial to the degradation of landfilled waste and mitigated the discharge amount of pollutants at the hydraulic loading rate of 5.9 L m(-2) day(-1). As the hydraulic loading rate of the joint injection of leachate and concentrated leachate was increased from 5.9 to 17.6 L m(-2) day(-1), the organic matter, biologically degradable matter, and total nitrogen of landfilled waste were degraded more rapidly, with the degradation constant of the first-order kinetics of 0.005, 0.004, and 0.003, respectively. Additionally, NO2(-)-N and NO3(-)-N in the concentrated leachate could be well removed in the landfill bioreactors. These results showed that a joint injection of concentrated leachate and raw leachate might be a good way to relieve the inhibitory effect of high concentrations of toxic pollutants in the concentrated leachate and accelerate the stabilization of landfilled waste.
Nowakowski, Piotr
2017-02-01
Waste electrical and electronic equipment (WEEE), also known as e-waste, is one of the most important waste streams with high recycling potential. Materials used in these products are valuable, but some of them are hazardous. The urban mining approach attempts to recycle as many materials as possible, so efficiency in collection is vital. There are two main methods used to collect WEEE: stationary and mobile, each with different variants. The responsibility of WEEE organizations and waste collection companies is to assure all resources required for these activities - bins, containers, collection vehicles and staff - are available, taking into account cost minimization. Therefore, it is necessary to correctly determine the capacity of containers and number of collection vehicles for an area where WEEE need to be collected. There are two main problems encountered in collection, storage and transportation of WEEE: container loading problems and vehicle routing problems. In this study, an adaptation of these two models for packing and collecting WEEE is proposed, along with a practical implementation plan designed to be useful for collection companies' guidelines for container loading and route optimization. The solutions are presented in the case studies of real-world conditions for WEEE collection companies in Poland. Copyright © 2016 Elsevier Ltd. All rights reserved.
He, Jing; Wang, Xing; Yin, Xiao-Bo; Li, Qiang; Li, Xia; Zhang, Yun-Fei; Deng, Yu
2018-06-01
High content of lipids in food waste could restrict digestion rate and give rise to the accumulation of long chain fatty acids in anaerobic digester. In the present study, using waste cooking oil skimmed from food waste as the sole carbon source, the effect of organic loading rate (OLR) on the methane production and microbial community dynamics were well investigated. Results showed that stable biomethane production was obtained at an organic loading rate of 0.5-1.5 g VS L -1 days -1 . The specific biogas/methane yield values at OLR of 1.0 were 1.44 ± 0.15 and 0.98 ± 0.11 L g VS -1 , respectively. The amplicon pyrosequencing revealed the distinct microbial succession in waste cooking oil AD reactors. Acetoclastic methanogens belonging to the genus Methanosaeta were the most dominant archaea, while the genera Syntrophomona, Anaerovibrio and Synergistaceae were the most common bacteria during AD process. Furthermore, redundancy analysis indicated that OLR showed more significant effect on the bacterial communities than that of archaeal communities. Additionally, whether the OLR of lipids increased had slight influence on the acetate fermentation pathway.
Workload Assessment for the Combat Vehicle Command and Control Company- Level Evaluation
1992-04-01
and descriptive statistics are in Appendix F3 . Shell and SITREP Reports. No significant total score workload differences were obtained for these tasks...Cases= 9: missing Cases = 15 OR 16.5 PCT. F2-20 Appendix F3 Prepare/Send CFF Report Variable or term GRP(l) ANOVA factor comparing CVCC with Ml Baseline...subscale score for task CMT4WL5 Effort subscale score for task CMT4WL6 Frustration subscale score for task F3 -1 Deviation Scores: Task 4 - Prepare/Send CFF
Student Support to WL/ML and WL/AA
1993-01-01
the program, so please be candid. I. How did you learn about the Student Support Program? Check one. 14 a) Advertisement (flyer, brochure, campus paper...scientific research 25 27 3 1 3. I was satisfied with the way I spent my time 41 13 2 0 4. I learned a lot 32 21 3 0 5. I feel I contributed to the research...are being sought out and tested daily with the hope that from deep within these crystalline fretworks a signal may appear leading to further study and
Temperature-dependent evolution of the wetting layer thickness during Ge deposition on Si(001).
Bergamaschini, R; Brehm, M; Grydlik, M; Fromherz, T; Bauer, G; Montalenti, F
2011-07-15
The evolution of the wetting layer (WL) thickness during Ge deposition on Si(001) is analyzed with the help of a rate-equation approach. The combined role of thickness, island volume and shape-dependent chemical potentials is considered. Several experimental observations, such as WL thinning following the pyramid-to-dome transformation, are captured by the model, as directly demonstrated by a close comparison with photoluminescence measurements (PL) on samples grown at three different temperatures. The limitations of the model in describing late stages of growth are critically addressed.
Sources and potential application of waste heat utilization at a gas processing facility
NASA Astrophysics Data System (ADS)
Alshehhi, Alyas Ali
Waste heat recovery (WHR) has the potential to significantly improve the efficiency of oil and gas plants, chemical and other processing facilities, and reduce their environmental impact. In this Thesis a comprehensive energy audit at Abu Dhabi Gas Industries Ltd. (GASCO) ASAB gas processing facilities is undertaken to identify sources of waste heat and evaluate their potential for on-site recovery. Two plants are considered, namely ASAB0 and ASAB1. Waste heat evaluation criteria include waste heat grade (i.e., temperature), rate, accessibility (i.e., proximity) to potential on-site waste heat recovery applications, and potential impact of recovery on installation performance and safety. The operating parameters of key waste heat source producing equipment are compiled, as well as characteristics of the waste heat streams. In addition, potential waste heat recovery applications and strategies are proposed, focusing on utilities, i.e., enhancement of process cooling/heating, electrical/mechanical power generation, and steam production. The sources of waste heat identified at ASAB facilities consist of gas turbine and gas generator exhaust gases, flared gases, excess propane cooling capacity, excess process steam, process gas air-cooler heat dissipation, furnace exhaust gases and steam turbine outlet steam. Of the above waste heat sources, exhaust gases from five gas turbines and one gas generator at ASAB0 plant, as well as from four gas turbines at ASAB1 plant, were found to meet the rate (i.e., > 1 MW), grade (i.e., > 180°C), accessibility (i.e., < 50 m from potential on-site WHR applications) and minimal impact criteria on the performance and safety of existing installations, for potential waste heat recovery. The total amount of waste heat meeting these criteria were estimated at 256 MW and 289 MW at ASAB0 and ASAB1 plants, respectively, both of which are substantial. Of the 289 MW waste generated at ASAB1, approximately 173 MW are recovered by waste heat recovery steam generators (WHRSGs), leaving 116 MW unutilized. The following strategies were developed to recover the above waste heat. At ASAB0, it is proposed that exhaust gases from all five gas turbines be used to power a WHRSG. The steam generated by the WHRSG would both i) drive an absorption refrigeration unit for gas turbine inlet air cooling, which would result in additional electric or mechanical power generation, and pre-cooling of process gas, which could reduce the need for or eliminate air coolers, as well as reduce propane chiller load, and ii) serve for heating of lean gas, which would reduce furnace load. At ASAB1, it is proposed that exhaust gases from all four gas turbines be used to generate steam in WHRSG that would drive an absorption refrigeration unit for either gas turbine inlet air cooling for additional electric or mechanical power generation, or pre-cooling of process gas to eliminate air-coolers and reduce propane chiller cooling load. Considering the smaller amount of waste heat available at ASAB1 (116 MW) relative to ASAB0 (237 MW), these above two recovery options could not be implemented simultaneously at ASAB0. To permit the detailed design and techno-economic feasibility evaluation of the proposed waste heat recovery strategies in a subsequent study, the cooling loads and associated electric power consumption of ASAB0 process gas air-coolers were estimated at 21 MW and 1.9 MW, respectively, and 67 MW and 2.2 MW, respectively for ASAB1 plant. In addition, the heating loads and fuel consumption of ASAB0 furnaces used for lean gas re-generation were estimated at 24 MW and 0.0653 MMSCMD, respectively. In modeling work undertaken in parallel with this study at the Petroleum Institute, the waste heat recovery strategies proposed here were found to be thermodynamically and economically feasible, and to lead to substantial energy and cost savings, hence environmental benefits.
Changing ecosystem response to nitrogen load into Buzzards Bay, MA
NASA Astrophysics Data System (ADS)
Williamson, S.; Rheuban, J. E.; Costa, J. E.; Glover, D. M.; Doney, S. C.
2016-02-01
Nitrogen (N) and chlorophyll-a (Chla) concentration in estuarine systems often correlate positively with increased N inputs. Evaluation of a long-term water quality data set (1992 -2013) for Buzzards Bay, MA, however reveals that ecosystem response to N inputs may be changing over time, as represented by increased yield of Chla per unit total nitrogen (TN) from 1992-2013. To determine if this change is caused by changes in nitrogen sources, we estimate nitrogen input from 28 watersheds. Combining parcel specific waste water disposal, land use, and atmospheric deposition data, we estimated N loads into Buzzards Bay from 1985-2013 using a previously verified Nitrogen Loading Model. Of the 28 watersheds analyzed, the six largest watersheds released the largest absolute N loads into receiving estuaries ranging from approximately 50,000-220,000 kg N yr-1. Normalizing N loads by watershed and estuarine areas revealed that smaller watersheds release some of the greatest relative loads into estuaries making these watersheds more vulnerable to increases in N load. A linear regression analysis of N load through time revealed decreasing N loads for most watersheds on the western side of Buzzards Bay which we believe is reflecting decreased atmospheric N from 1985-2013. Out of the ten sub-watersheds on the eastern side, increases in human waste, driven primarily by increased parcels on septic have resulted in overall N load increases for 9 watersheds. Comparison of in situ TN and Chla concentrations with N load estimates for several watersheds and adjoining estuaries suggest that varied ecosystem responses to N load may be reflecting differences in physical stressors such as estuarine morphology, residence time, and climate change. Results of this study also reveal the importance of watershed specific mitigation efforts to best accommodate dominant N sources which may be influenced regionally (atmospheric N) and locally (fertilizer and human waste).
Tränkler, J; Visvanathan, C; Kuruparan, P; Tubtimthai, O
2005-01-01
Considering the quality of design and construction of landfills in developing countries, little information can be derived from randomly taken leachate samples. Leachate generation and composition under monsoon conditions have been studied using lysimeters to simulate sanitary landfills and open cell settings. In this study, lysimeters were filled with domestic waste, highly organic market waste and pre-treated waste. Results over two subsequent dry and rainy seasons indicate that the open cell lysimeter simulation showed the highest leachate generation throughout the rainy season, with leachate flow in all lysimeters coming to a halt during the dry periods. More than 60% of the precipitation was found in the form of leachate. The specific COD and TKN load discharged from the open cell was 20% and 180% more than that of the sanitary landfill lysimeters. Types of waste material and kind of pre-treatment prior to landfilling strongly influenced the pollutant load. Compared to the sanitary landfill lysimeter filled with domestic waste, the specific COD and TKN load discharged from the pre-treated waste lysimeter accounted for only 4% and 16%, respectively. Considering the local settings of tropical landfills, these results suggest that landfill design and operation has to be adjusted. Leachate can be collected and stored during the rainy season, and recirculation of leachate is recommended to maintain a steady and even accelerated degradation during the prolonged dry season. The open cell approach in combination with leachate recirculation is suggested as an option for interim landfill operations.
Tallis, Jason; Hill, Cameron; James, Rob S; Cox, Val M; Seebacher, Frank
2017-01-01
Obesity affects the major metabolic and cellular processes involved in skeletal muscle contractility. Surprisingly, the effect of obesity on isolated skeletal muscle performance remains unresolved. The present study is the first to examine the muscle-specific changes in contractility following dietary-induced obesity using an isolated muscle work-loop (WL) model that more closely represents in vivo muscle performance. Following 16-wk high-calorific feeding, soleus (SOL), extensor digitorum longus (EDL), and diaphragm (DIA) were isolated from female (CD-1) mice, and contractile performance was compared against a lean control group. Obese SOL produced greater isometric force; however, isometric stress (force per unit muscle area), absolute WL power, and normalized WL power (watts per kilogram muscle mass) were unaffected. Maximal isometric force and absolute WL power of the EDL were similar between groups. For both EDL and DIA, isometric stress and normalized WL power were reduced in the obese groups. Obesity caused a significant reduction in fatigue resistance in all cases. Our findings demonstrate a muscle-specific reduction in contractile performance and muscle quality that is likely related to in vivo mechanical role, fiber type, and metabolic profile, which may in part be related to changes in myosin heavy chain expression and AMP-activated protein kinase activity. These results infer that, beyond the additional requirement of moving a larger body mass, functional performance and quality of life may be further limited by poor muscle function in obese individuals. As such, a reduction in muscle performance may be a substantial contributor to the negative cycle of obesity. The effect of obesity on isolated muscle function is surprisingly underresearched. The present study is the first to examine the effects of obesity on isolated muscle performance using a method that more closely represents real-world muscle function. This work uniquely establishes a muscle-specific profile of mechanical changes in relation to underpinning mechanisms. These findings may be important to understanding the negative cycle of obesity and in designing interventions for improving weight status. Copyright © 2017 the American Physiological Society.
An Improved BeiDou-2 Satellite-Induced Code Bias Estimation Method.
Fu, Jingyang; Li, Guangyun; Wang, Li
2018-04-27
Different from GPS, GLONASS, GALILEO and BeiDou-3, it is confirmed that the code multipath bias (CMB), which originate from the satellite end and can be over 1 m, are commonly found in the code observations of BeiDou-2 (BDS) IGSO and MEO satellites. In order to mitigate their adverse effects on absolute precise applications which use the code measurements, we propose in this paper an improved correction model to estimate the CMB. Different from the traditional model which considering the correction values are orbit-type dependent (estimating two sets of values for IGSO and MEO, respectively) and modeling the CMB as a piecewise linear function with a elevation node separation of 10°, we estimate the corrections for each BDS IGSO + MEO satellite on one hand, and a denser elevation node separation of 5° is used to model the CMB variations on the other hand. Currently, the institutions such as IGS-MGEX operate over 120 stations which providing the daily BDS observations. These large amounts of data provide adequate support to refine the CMB estimation satellite by satellite in our improved model. One month BDS observations from MGEX are used for assessing the performance of the improved CMB model by means of precise point positioning (PPP). Experimental results show that for the satellites on the same orbit type, obvious differences can be found in the CMB at the same node and frequency. Results show that the new correction model can improve the wide-lane (WL) ambiguity usage rate for WL fractional cycle bias estimation, shorten the WL and narrow-lane (NL) time to first fix (TTFF) in PPP ambiguity resolution (AR) as well as improve the PPP positioning accuracy. With our improved correction model, the usage of WL ambiguity is increased from 94.1% to 96.0%, the WL and NL TTFF of PPP AR is shorten from 10.6 to 9.3 min, 67.9 to 63.3 min, respectively, compared with the traditional correction model. In addition, both the traditional and improved CMB model have a better performance in these aspects compared with the model which does not account for the CMB correction.
An Improved BeiDou-2 Satellite-Induced Code Bias Estimation Method
Fu, Jingyang; Li, Guangyun; Wang, Li
2018-01-01
Different from GPS, GLONASS, GALILEO and BeiDou-3, it is confirmed that the code multipath bias (CMB), which originate from the satellite end and can be over 1 m, are commonly found in the code observations of BeiDou-2 (BDS) IGSO and MEO satellites. In order to mitigate their adverse effects on absolute precise applications which use the code measurements, we propose in this paper an improved correction model to estimate the CMB. Different from the traditional model which considering the correction values are orbit-type dependent (estimating two sets of values for IGSO and MEO, respectively) and modeling the CMB as a piecewise linear function with a elevation node separation of 10°, we estimate the corrections for each BDS IGSO + MEO satellite on one hand, and a denser elevation node separation of 5° is used to model the CMB variations on the other hand. Currently, the institutions such as IGS-MGEX operate over 120 stations which providing the daily BDS observations. These large amounts of data provide adequate support to refine the CMB estimation satellite by satellite in our improved model. One month BDS observations from MGEX are used for assessing the performance of the improved CMB model by means of precise point positioning (PPP). Experimental results show that for the satellites on the same orbit type, obvious differences can be found in the CMB at the same node and frequency. Results show that the new correction model can improve the wide-lane (WL) ambiguity usage rate for WL fractional cycle bias estimation, shorten the WL and narrow-lane (NL) time to first fix (TTFF) in PPP ambiguity resolution (AR) as well as improve the PPP positioning accuracy. With our improved correction model, the usage of WL ambiguity is increased from 94.1% to 96.0%, the WL and NL TTFF of PPP AR is shorten from 10.6 to 9.3 min, 67.9 to 63.3 min, respectively, compared with the traditional correction model. In addition, both the traditional and improved CMB model have a better performance in these aspects compared with the model which does not account for the CMB correction. PMID:29702559
Oxygen isotopic variations in the outer margins and Wark–Lovering rims of refractory inclusions
Simon, Justin I.; Matzel, Jennifer E. P.; Simon, Steven B.; ...
2016-05-02
Oxygen isotopic variations across the outer margins and Wark–Lovering (WL) rims of a diverse suite of six coarse-grained Types A and B refractory inclusions from both oxidized and reduced CV3 chondrites suggest that CAIs originated from a 16O-rich protosolar gas reservoir and were later exposed to both relatively 17,18O-rich and 16O-rich reservoirs. The O-isotope profiles of CAIs can be explained by changes in the composition of gas near the protoSun or the migration of CAIs through a heterogeneous nebula. Variability within the inclusion interiors appears to have been set prior to WL rim growth. Modeling the isotopic zoning profiles asmore » diffusion gradients between inclusion interiors and edges establishes a range of permissible time–temperature combinations for their exposure in the nebula. At mean temperatures of 1400 K, models that match the isotope gradients in the inclusions yield timescales ranging from 5 × 10 3 to 3 × 10 5 years. Assuming CAIs originated with a relatively 16O-rich (protosolar) isotopic composition, differences among the melilite interiors and the isotopic gradients in their margins imply the existence of a number of isotopically distinct reservoirs. In addition, evidence at the edges of some CAIs for subsequent isotopic exchange may relate to the beginning of rim formation. In the WL rim layers surrounding the interiors, spinel is relatively 16O-rich but subtly distinct among different CAIs. Melilite is often relatively 16O-poor, but rare relatively 16O-rich grains also exist. Pyroxene generally exhibits intermediate O-isotope compositions and isotopic zoning. Olivine in both WL and accretionary rims, when present, is isotopically heterogeneous. The extreme isotopic heterogeneity among and within individual WL rim layers and in particular, the observed trends of outward 16O-enrichments, suggest that rims surrounding CAIs contained in CV3 chondrites, like the inclusions themselves, formed from a number of isotopically distinct gas reservoirs. Collectively, these results support numerical protoplanetary disk models in which CAIs were transported between several distinct nebular reservoirs multiple times prior to accretion onto a parent body.« less
Lynn, Tin Mar; Liu, Qiong; Hu, Yajun; Yuan, Hongzhao; Wu, Xiaohong; Khai, Aye Aye; Wu, Jinshui; Ge, Tida
2017-07-01
Studying shifts in microbial communities under different land use can help in determining the impact of land use on microbial diversity. In this study, we analyzed four different land-use types to determine their bacterial and archaeal diversity and abundance. Three natural ecosystems, that is, wetland (WL), grassland (GL), and forest (FR) soils, and one agricultural soil, that is, tea plantation (TP) soil, were investigated to determine how land use shapes bacterial and archaeal diversity. For this purpose, molecular analyses, such as quantitative polymerase chain reaction (Q-PCR), 16S rRNA gene sequencing, and terminal restriction fragment length polymorphism (T-RFLP), were used. Soil physicochemical properties were determined, and statistical analyses were performed to identify the key factors affecting microbial diversity in these soils. Phylogenetic affiliations determined using the Ribosomal Database Project (RDP) database and T-RFLP revealed that the soils had differing bacterial diversity. WL soil was rich in only Proteobacteria, whereas GR soil was rich in Proteobacteria, followed by Actinobacteria. FR soil had higher abundance of Chloroflexi species than these soils. TP soil was rich in Actinobacteria, followed by Chloroflexi, Acidobacteria, Proteobacteria, and Firmicutes. The archaeal diversity of GL and FR soils was similar in that most of their sequences were closely related to Nitrososphaerales (Thaumarchaeota phylum). In contrast, WL soil, followed by TP soil, had greater archaeal diversity than other soils. Eight different archaeal classes were found in WL soil, and Pacearchaeota class was the richest one. The abundance of bacterial and archaeal 16S rRNA gene copies in WL and GL soils was significantly higher than that in FR and TP soils. Redundancy analysis showed that bacterial diversity was influenced by abiotic factors, e.g., total organic carbon and pH, whereas total nitrogen, pH, and cation exchange capacity (CEC) significantly affected archaeal community composition. Pearson correlation analysis showed that bacterial and archaeal 16S rRNA gene abundance had the highest correlation with clay content (r > 0.905, P < 0.01), followed by total-P, CEC, pH, and silt (%). These results will lead to more comprehensive understanding of how land use affects microbial distribution.
Xie, D; Li, J; Wang, Z X; Cao, J; Li, T T; Chen, J L; Chen, Y X
2011-12-01
Our previous studies demonstrated that green and blue monochromatic lights were effective to stimulate immune response of the spleen in broilers. This study was designed to investigate the effects of monochromatic light on both gut mucosal mechanical and immunological barriers. A total of 120 Arbor Acre male broilers on post-hatching day (P) 0 were exposed to red light, green light (GL), blue light (BL), and white light (WL) for 49 d, respectively. As compared with broilers exposed to WL, the broilers exposed to GL showed that the villus height of small intestine was increased by 19.5% (P = 0.0205) and 38.8% (P = 0.0149), the crypt depth of small intestine was decreased by 15.1% (P = 0.0049) and 10.1% (P = 0.0005), and the ratios of villus height to crypt depth were increased by 39.3% (P < 0.0001) and 52.5% (P < 0.0001) at P7 and P21, respectively. Until P49, an increased villus height (33.6%, P = 0.0076), a decreased crypt depth (15.4%, P = 0.0201), and an increased villus height-to-crypt depth ratio (58.5%, P < 0.0001) were observed in the BL group as compared with the WL group. On the other hand, the numbers of intestinal intraepithelial lymphocytes (27.9%, P < 0.0001 and 37.0%, P < 0.0001), goblet cells (GC, 22.1%, P < 0.0001 and 18.1%, P < 0.0001), and IgA(+) cells (14.8%, P = 0.0543 and 47.9%, P = 0.0377) in the small intestine were significantly increased in the GL group as compared with the WL group at P7 and P21, respectively. The numbers of intestinal intraepithelial lymphocytes (36.2%, P < 0.0001), GC (26.5%, P < 0.0001), and IgA(+) cells (68.0%, P = 0.0177) in the BL group were also higher than those in the WL group at P49. These results suggest that both mucosal mechanical and immunological barriers of the small intestine may be improved by rearing broilers under GL at an early age and under BL at an older age.
Effect of water level drawdown on decomposition in boreal peatlands
NASA Astrophysics Data System (ADS)
Straková, Petra; Penttilä, Timo; Laiho, Raija
2010-05-01
Plant litter production and decomposition are key processes in element cycling in most ecosystems. In peatlands, there has been a long-term imbalance between litter production and decay caused by high water levels (WL) and consequent anoxia. This has resulted in peatlands being a significant sink of carbon (C) from the atmosphere. However, peatlands are experiencing both "natural" (global climate change) and anthropogenic (ditching) changes that threaten their ability to retain this ecosystem identity and function. Many of these alterations can be traced back to WL drawdown, which can cause increased aeration, higher acidity, falling temperatures, and a greater probability of drought. Such changes are also associated with an increasing decomposition rate, and therefore a greater amount of C released back to the atmosphere. Yet studies about how the overall C balance of peatlands will be affected have come up with conflicting conclusions, demonstrating that the C store could increase, decrease, or remain static. A factor that has been largely overlooked is the change in litter type composition following persistent WL drawdown. It is the aim of our study, then, to help to resolve this issue. We studied the effects of short-term (ca. 4 years) and long-term (ca. 40 years) persistent WL drawdown on the decomposition of numerous types of above-ground and below-ground plant litters at three boreal peatland sites: bog, oligotrophic fen and mesotrophic fen. We thus believe that enough permutations have been created to obtain a good assessment of how each factor, site nutrient level, WL regime, and litter type composition, influences decomposition. We used the litter bag method to measure the decomposition rates: placed measured amounts of plant litter, or cellulose strips as a control, into closed mesh bags, and installed the bags in the natural environment for decomposition for each litter type for varying amounts of time. Following litter bag recovery, the litter was cleaned of excess debris and analyzed for changes in mass, enzyme activity, mesofauna presence, and microbial community composition, among other things. The experiment has a run-time of ten years, the results from the first two years are presented in the poster.
Zhao, Jinfang; Xu, Liyuan; Wang, Yongze; Zhao, Xiao; Wang, Jinhua; Garza, Erin; Manow, Ryan; Zhou, Shengde
2013-06-07
Polylactic acid (PLA), a biodegradable polymer, has the potential to replace (at least partially) traditional petroleum-based plastics, minimizing "white pollution". However, cost-effective production of optically pure L-lactic acid is needed to achieve the full potential of PLA. Currently, starch-based glucose is used for L-lactic acid fermentation by lactic acid bacteria. Due to its competition with food resources, an alternative non-food substrate such as cellulosic biomass is needed for L-lactic acid fermentation. Nevertheless, the substrate (sugar stream) derived from cellulosic biomass contains significant amounts of xylose, which is unfermentable by most lactic acid bacteria. However, the microorganisms that do ferment xylose usually carry out heterolactic acid fermentation. As a result, an alternative strain should be developed for homofermentative production of optically pure L-lactic acid using cellulosic biomass. In this study, an ethanologenic Escherichia coli strain, SZ470 (ΔfrdBC ΔldhA ΔackA ΔpflB ΔpdhR ::pflBp6-acEF-lpd ΔmgsA), was reengineered for homofermentative production of L-lactic acid from xylose (1.2 mole xylose = > 2 mole L-lactic acid), by deleting the alcohol dehydrogenase gene (adhE) and integrating the L-lactate dehydrogenase gene (ldhL) of Pediococcus acidilactici. The resulting strain, WL203, was metabolically evolved further through serial transfers in screw-cap tubes containing xylose, resulting in the strain WL204 with improved anaerobic cell growth. When tested in 70 g L-1 xylose fermentation (complex medium), WL204 produced 62 g L-1 L-lactic acid, with a maximum production rate of 1.631 g L-1 h-1 and a yield of 97% based on xylose metabolized. HPLC analysis using a chiral column showed that an L-lactic acid optical purity of 99.5% was achieved by WL204. These results demonstrated that WL204 has the potential for homofermentative production of L-lactic acid using cellulosic biomass derived substrates, which contain a significant amount of xylose.
Oxygen isotopic variations in the outer margins and Wark-Lovering rims of refractory inclusions
NASA Astrophysics Data System (ADS)
Simon, Justin I.; Matzel, Jennifer E. P.; Simon, Steven B.; Hutcheon, Ian D.; Ross, D. Kent; Weber, Peter K.; Grossman, Lawrence
2016-08-01
Oxygen isotopic variations across the outer margins and Wark-Lovering (WL) rims of a diverse suite of six coarse-grained Types A and B refractory inclusions from both oxidized and reduced CV3 chondrites suggest that CAIs originated from a 16O-rich protosolar gas reservoir and were later exposed to both relatively 17,18O-rich and 16O-rich reservoirs. The O-isotope profiles of CAIs can be explained by changes in the composition of gas near the protoSun or the migration of CAIs through a heterogeneous nebula. Variability within the inclusion interiors appears to have been set prior to WL rim growth. Modeling the isotopic zoning profiles as diffusion gradients between inclusion interiors and edges establishes a range of permissible time-temperature combinations for their exposure in the nebula. At mean temperatures of 1400 K, models that match the isotope gradients in the inclusions yield timescales ranging from 5 × 103 to 3 × 105 years. Assuming CAIs originated with a relatively 16O-rich (protosolar) isotopic composition, differences among the melilite interiors and the isotopic gradients in their margins imply the existence of a number of isotopically distinct reservoirs. Evidence at the edges of some CAIs for subsequent isotopic exchange may relate to the beginning of rim formation. In the WL rim layers surrounding the interiors, spinel is relatively 16O-rich but subtly distinct among different CAIs. Melilite is often relatively 16O-poor, but rare relatively 16O-rich grains also exist. Pyroxene generally exhibits intermediate O-isotope compositions and isotopic zoning. Olivine in both WL and accretionary rims, when present, is isotopically heterogeneous. The extreme isotopic heterogeneity among and within individual WL rim layers and in particular, the observed trends of outward 16O-enrichments, suggest that rims surrounding CAIs contained in CV3 chondrites, like the inclusions themselves, formed from a number of isotopically distinct gas reservoirs. Collectively, these results support numerical protoplanetary disk models in which CAIs were transported between several distinct nebular reservoirs multiple times prior to accretion onto a parent body.
Stummer, Walter; Tonn, Jörg-Christian; Mehdorn, Hubertus Maximilian; Nestler, Ulf; Franz, Kea; Goetz, Claudia; Bink, Andrea; Pichlmeier, Uwe
2011-03-01
Accumulating data suggest more aggressive surgery in patients with malignant glioma to improve outcome. However, extended surgery may increase morbidity. The randomized Phase III 5-aminolevulinic acid (ALA) study investigated 5-ALA-induced fluorescence as a tool for improving resections. An interim analysis demonstrated more frequent complete resections with longer progression-free survival (PFS). However, marginal differences were found regarding neurological deterioration and the frequency of additional therapies. Presently, the authors focus on the latter aspects in the final study population, and attempt to determine how safety might be affected by cytoreductive surgery. Patients with malignant gliomas were randomized for fluorescence-guided (ALA group) or conventional white light (WL) (WL group) microsurgery. The final intent-to-treat population consisted of 176 patients in the ALA and 173 in the WL group. Primary efficacy variables were contrast-enhancing tumor on early MR imaging and 6-month PFS. Among secondary outcome measures, the National Institutes of Health Stroke Scale (NIH-SS) score and the Karnofsky Performance Scale (KPS) score were used for assessing neurological function. More frequent complete resections and improved PFS were confirmed, with higher median residual tumor volumes in the WL group (0.5 vs 0 cm(3), p = 0.001). Patients in the ALA group had more frequent deterioration on the NIH-SS at 48 hours. Patients at risk were those with deficits unresponsive to steroids. No differences were found in the KPS score. Regarding outcome, a combined end point of risks and neurological deficits was attempted, which demonstrated results in patients in the ALA group to be superior to those in participants in the WL group. Interestingly, the cumulative incidence of repeat surgery was significantly reduced in ALA patients. When stratified by completeness of resection, patients with incomplete resections were quicker to deteriorate neurologically (p = 0.0036). Extended resections performed using a tool such as 5-ALA-derived tumor fluorescence, carries the risk of temporary impairment of neurological function. However, risks are higher in patients with deficits unresponsive to steroids.
Paschoal, Marco Aurelio; Santos-Pinto, Lourdes; Lin, Meng
2014-01-01
Abstract Objective: Investigate the photodynamic antimicrobial effect by the combination of a novel noncoherent broad spectrum visible light and low concentrations of curcumin and toluidine blue over suspensions of Streptococcus mutans. Background data: Long illumination times to activate photosensitizers (PS) and the use of high concentrations of these drugs in photodynamic antimicrobial chemotherapy (PACT) are limitations of its application as an antimicrobial technology in dental practice. Materials and methods: Planktonic suspensions of S. mutans were standardized and submitted to PACT treatment at low concentrations of curcumin (C) (0.075; 0.75 and 7.5 μM) and toluidine blue (T) (0.25; 2.5 and 25 μM) exposed to 42 J/cm2 (12.2 sec; set power: 3.930 mW) of a white light (WL) (output wavelength range: 400–700 nm; beam diameter: 12 mm) (C+WL+ and T+WL+, PACT groups; incubation time, C: 60 sec; T: 5 min); isolated effect of both C (C+WL−) and T concentrations (T+WL−); effect of light source (C−WL+ and T−WL+) and suspensions neither submitted to PS nor to light-emitting diode (LED) illumination (control groups, C−WL− and T−WL−). Aliquots of each group were diluted and cultured on blood agar plates and the number of colony-forming units (CFU)/mL was recorded, transformed into log10 and analyzed by ANOVA and Tukey's test at a cutoff value at 0.05. Results: The groups submitted to PACT presented a bacterial reduction value of>5-log10 to both tested PS in comparison with control groups (p<0.05). PS or light source used alone demonstrated no antimicrobial effect on the number of viable bacterial counts. Conclusions: The combination of a novel noncoherent light at short illumination exposure time with low concentrations of studied PS achieved a lethal photoinactivation of S. mutans, and can be considered an effective antimicrobial in vitro approach for reducing the number of micro-organisms involved with the dental caries process. PMID:24552467
40 CFR 270.24 - Specific part B information requirements for process vents.
Code of Federal Regulations, 2010 CFR
2010-07-01
...., identify the hazardous waste management units on a facility plot plan). (2) Information and data supporting... concentrations) that represent the conditions that exist when the waste management unit is operating at the... when the hazardous waste management unit is or would be operating at the highest load or capacity level...
Epsilon Metal Waste Form for Immobilization of Noble Metals from Used Nuclear Fuel
DOE Office of Scientific and Technical Information (OSTI.GOV)
Crum, Jarrod V.; Strachan, Denis M.; Rohatgi, Aashish
2013-10-01
Epsilon metal (ε-metal), an alloy of Mo, Pd, Rh, Ru, and Tc, is being developed as a waste form to treat and immobilize the undissolved solids and dissolved noble metals from aqueous reprocessing of commercial used nuclear fuel. Epsilon metal is an attractive waste form for several reasons: increased durability relative to borosilicate glass, it can be fabricated without additives (100% waste loading), and in addition it also benefits borosilicate glass waste loading by eliminating noble metals from the glass and thus the processing problems related there insolubility in glass. This work focused on the processing aspects of the epsilonmore » metal waste form development. Epsilon metal is comprised of refractory metals resulting in high reaction temperatures to form the alloy, expected to be 1500 - 2000°C making it a non-trivial phase to fabricate by traditional methods. Three commercially available advanced technologies were identified: spark-plasma sintering, microwave sintering, and hot isostatic pressing, and investigated as potential methods to fabricate this waste form. Results of these investigations are reported and compared in terms of bulk density, phase assemblage (X-ray diffraction and elemental analysis), and microstructure (scanning electron microscopy).« less
Epsilon metal waste form for immobilization of noble metals from used nuclear fuel
NASA Astrophysics Data System (ADS)
Crum, Jarrod V.; Strachan, Denis; Rohatgi, Aashish; Zumhoff, Mac
2013-10-01
Epsilon metal (ɛ-metal), an alloy of Mo, Pd, Rh, Ru, and Tc, is being developed as a waste form to treat and immobilize the undissolved solids and dissolved noble metals from aqueous reprocessing of commercial used nuclear fuel. Epsilon metal is an attractive waste form for several reasons: increased durability relative to borosilicate glass, it can be fabricated without additives (100% waste loading), and in addition it also benefits borosilicate glass waste loading by eliminating noble metals from the glass, thus the processing problems related to their insolubility in glass. This work focused on the processing aspects of the epsilon metal waste form development. Epsilon metal is comprised of refractory metals resulting in high alloying temperatures, expected to be 1500-2000 °C, making it a non-trivial phase to fabricate by traditional methods. Three commercially available advanced technologies were identified: spark-plasma sintering, microwave sintering, and hot isostatic pressing, and investigated as potential methods to fabricate this waste form. Results of these investigations are reported and compared in terms of bulk density, phase assemblage (X-ray diffraction and elemental analysis), and microstructure (scanning electron microscopy).
DOE Office of Scientific and Technical Information (OSTI.GOV)
Jantzen, Carol; Herman, Connie; Crawford, Charles
One of the immobilization technologies under consideration as a Supplemental Treatment for Hanford’s Low Activity Waste (LAW) is Fluidized Bed Steam Reforming (FBSR). The FBSR technology forms a mineral waste form at moderate processing temperatures thus retaining and atomically bonding the halides, sulfates, and technetium in the mineral phases (nepheline, sodalite, nosean, carnegieite). Additions of kaolin clay are used instead of glass formers and the minerals formed by the FBSR technology offers (1) atomic bonding of the radionuclides and constituents of concern (COC) comparable to glass, (2) short and long term durability comparable to glass, (3) disposal volumes comparable tomore » glass, and (4) higher Na2O and SO{sub 4} waste loadings than glass. The higher FBSR Na{sub 2}O and SO{sub 4} waste loadings contribute to the low disposal volumes but also provide for more rapid processing of the LAW. Recent FBSR processing and testing of Hanford radioactive LAW (Tank SX-105 and AN-103) waste is reported and compared to previous radioactive and non-radioactive LAW processing and testing.« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ghosh, A.; Hsiung, S.M.; Chowdhury, A.H.
Long-term stability of emplacement drifts and potential near-field fluid flow resulting from coupled effects are among the concerns for safe disposal of high-level nuclear waste (HLW). A number of factors can induce drift instability or change the near-field flow patterns. Repetitive seismic loads from earthquakes and thermal loads generated by the decay of emplaced waste are two significant factors. One of two key technical uncertainties (KTU) that can potentially pose a high risk of noncompliance with the performance objectives of 10 CFR Part 60 is the prediction of thermal-mechanical (including repetitive seismic load) effects on stability of emplacement drifts andmore » the engineered barrier system. The second KTU of concern is the prediction of thermal-mechanical-hydrological (including repetitive seismic load) effects on the host rock surrounding the engineered barrier system. The Rock Mechanics research project being conducted at the Center for Nuclear Waste Regulatory Analyses (CNWRA) is intended to address certain specific technical issues associated with these two KTUs. This research project has two major components: (i) seismic response of rock joints and a jointed rock mass and (ii) coupled thermal-mechanical-hydrological (TMH) response of a jointed rock mass surrounding the engineered barrier system (EBS). This final report summarizes the research activities concerned with the repetitive seismic load aspect of both these KTUs.« less
Examining Mediators and Moderators of Yoga for Women With Breast Cancer Undergoing Radiotherapy
Ratcliff, Chelsea G.; Milbury, Kathrin; Chandwani, Kavita D.; Chaoul, Alejandro; Perkins, George; Nagarathna, Raghuram; Haddad, Robin; Nagendra, Hongasandra Ramarao; Raghuram, N. V.; Spelman, Amy; Arun, Banu; Wei, Qi; Cohen, Lorenzo
2016-01-01
Hypothesis. This study examines moderators and mediators of a yoga intervention targeting quality-of-life (QOL) outcomes in women with breast cancer receiving radiotherapy.Methods. Women undergoing 6 weeks of radiotherapy were randomized to a yoga (YG; n = 53) or stretching (ST; n = 56) intervention or a waitlist control group (WL; n = 54). Depressive symptoms and sleep disturbances were measured at baseline. Mediator (posttraumatic stress symptoms, benefit finding, and cortisol slope) and outcome (36-item Short Form [SF]-36 mental and physical component scales [MCS and PCS]) variables were assessed at baseline, end-of-treatment, and 1-, 3-, and 6-months posttreatment. Results. Baseline depressive symptoms (P = .03) and sleep disturbances (P < .01) moderated the Group × Time effect on MCS, but not PCS. Women with high baseline depressive symptoms in YG reported marginally higher 3-month MCS than their counterparts in WL (P = .11). Women with high baseline sleep disturbances in YG reported higher 3-months MCS than their counterparts in WL (P < .01) and higher 6-month MCS than their counterparts in ST (P = .01). YG led to greater benefit finding than ST and WL across the follow-up (P = .01). Three-month benefit finding partially mediated the effect of YG on 6-month PCS. Posttraumatic stress symptoms and cortisol slope did not mediate treatment effect on QOL. Conclusion. Yoga may provide the greatest mental-health–related QOL benefits for those experiencing pre-radiotherapy sleep disturbance and depressive symptoms. Yoga may improve physical-health–related QOL by increasing ability to find benefit in the cancer experience. PMID:26867802
Wacker, Jan
2018-01-01
The influence of positive emotions on the balance between cognitive stability and flexibility has been suggested to (a) differ among various positive emotional/motivational states (e.g., of varying approach motivation intensity), and (b) be mediated by brain dopamine (DA). Frontal EEG alpha asymmetry (ASY) is considered an indicator of approach motivational states and may be modulated by DA. The personality trait of extraversion is strongly linked to positive emotions and is now thought to reflect DA-based individual differences in incentive/approach motivation. The present study independently manipulated positive emotion (high approach wanting-expectancy [WE] vs. low approach warmth-liking [WL]) and dopamine (placebo vs. DA D2 blocker sulpiride) to examine their effects on both cognitive stability-flexibility and emotion-related ASY changes. The results showed numerically lower stability-flexibility in WE versus WL under placebo and a complete reversal of this effect under the D2 blocker, no differentiation between WE and WL groups in terms of emotion-related ASY change, but an association between self-reported WE and WL and ASY changes toward left and right frontal cortical activity, respectively. Finally, extraversion was positively associated with both stability-flexibility and ASY changes toward left frontal cortical activity under placebo, and these associations were completely reversed under the D2 blocker. The results (a) support a dopaminergic basis for frontal EEG asymmetry, extraversion, and the modulating effect of positive emotions on stability-flexibility, and (b) extend previous reports of cognitive differences between introverts and extraverts. © 2017 Society for Psychophysiological Research.
Reig García-Galbis, Manuel; Rizo Baeza, Mercedes; Cortés Castell, Ernesto
2015-09-01
WL%: percentage of weight loss; % FL: percentage fat loss; PNLWF: patients who lose weight or fat; PLWF: patients who lose weight and fat. assess whether the% WL and FL% in the dietary treatment was affected by gender, age, BMI and assistance to the query. 4,700 consultations, 670 patients (BMI ≥25), in the south-east of Spain (2006-12). Balanced and hypo-caloric diet was used. Two types of patients: PNLWF and PLWF (91.9%). in PLWF, men and those attending a greater number of occasions to the consultation have shown a greater loss against women (%FL: 23.0 vs 14.3%, p = 0.000; %WL: 7.7 vs 6.6%, p = 0.020), and those who attend less frequently (%FL: 19.1 vs 7.3%, p = 0.000; %WL: 7.8 vs 2.9%, p = 0.000). Multinomial regression analysis (PNLWF / PLWF) indicates that only attend more than one and a half to the consultation is a factor in the loss, OR 8.3 (IC 95% 4.5-15.1; p = 0.000). the body fat measurement provides additional information lost weight; Most patients attend more than six weeks, obtained a high %FL; attendance is a predictor of loss; the %FL indicates that the dietary management plays a major role in the resolution of this pathology; It is recommended to design practical schemes of action process nutritionists according to the IMCI and variable. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.
Sørensen, Thorkild I. A; Boutin, Philippe; Taylor, Moira A; Larsen, Lesli H; Verdich, Camilla; Petersen, Liselotte; Holst, Claus; Echwald, Søren M; Dina, Christian; Toubro, Søren; Petersen, Martin; Polak, Jan; Clément, Karine; Martínez, J. Alfredo; Langin, Dominique; Oppert, Jean-Michel; Stich, Vladimir; Macdonald, Ian; Arner, Peter; Saris, Wim H. M; Pedersen, Oluf; Astrup, Arne; Froguel, Philippe
2006-01-01
Objectives: To study if genes with common single nucleotide polymorphisms (SNPs) associated with obesity-related phenotypes influence weight loss (WL) in obese individuals treated by a hypo-energetic low-fat or high-fat diet. Design: Randomised, parallel, two-arm, open-label multi-centre trial. Setting: Eight clinical centres in seven European countries. Participants: 771 obese adult individuals. Interventions: 10-wk dietary intervention to hypo-energetic (−600 kcal/d) diets with a targeted fat energy of 20%–25% or 40%–45%, completed in 648 participants. Outcome Measures: WL during the 10 wk in relation to genotypes of 42 SNPs in 26 candidate genes, probably associated with hypothalamic regulation of appetite, efficiency of energy expenditure, regulation of adipocyte differentiation and function, lipid and glucose metabolism, or production of adipocytokines, determined in 642 participants. Results: Compared with the noncarriers of each of the SNPs, and after adjusting for gender, age, baseline weight and centre, heterozygotes showed WL differences that ranged from −0.6 to 0.8 kg, and homozygotes, from −0.7 to 3.1 kg. Genotype-dependent additional WL on low-fat diet ranged from 1.9 to −1.6 kg in heterozygotes, and from 3.8 kg to −2.1 kg in homozygotes relative to the noncarriers. Considering the multiple testing conducted, none of the associations was statistically significant. Conclusions: Polymorphisms in a panel of obesity-related candidate genes play a minor role, if any, in modulating weight changes induced by a moderate hypo-energetic low-fat or high-fat diet. PMID:16871334
Examining Mediators and Moderators of Yoga for Women With Breast Cancer Undergoing Radiotherapy.
Ratcliff, Chelsea G; Milbury, Kathrin; Chandwani, Kavita D; Chaoul, Alejandro; Perkins, George; Nagarathna, Raghuram; Haddad, Robin; Nagendra, Hongasandra Ramarao; Raghuram, N V; Spelman, Amy; Arun, Banu; Wei, Qi; Cohen, Lorenzo
2016-09-01
Hypothesis This study examines moderators and mediators of a yoga intervention targeting quality-of-life (QOL) outcomes in women with breast cancer receiving radiotherapy.Methods Women undergoing 6 weeks of radiotherapy were randomized to a yoga (YG; n = 53) or stretching (ST; n = 56) intervention or a waitlist control group (WL; n = 54). Depressive symptoms and sleep disturbances were measured at baseline. Mediator (posttraumatic stress symptoms, benefit finding, and cortisol slope) and outcome (36-item Short Form [SF]-36 mental and physical component scales [MCS and PCS]) variables were assessed at baseline, end-of-treatment, and 1-, 3-, and 6-months posttreatment. Results Baseline depressive symptoms (P = .03) and sleep disturbances (P < .01) moderated the Group × Time effect on MCS, but not PCS. Women with high baseline depressive symptoms in YG reported marginally higher 3-month MCS than their counterparts in WL (P = .11). Women with high baseline sleep disturbances in YG reported higher 3-months MCS than their counterparts in WL (P < .01) and higher 6-month MCS than their counterparts in ST (P = .01). YG led to greater benefit finding than ST and WL across the follow-up (P = .01). Three-month benefit finding partially mediated the effect of YG on 6-month PCS. Posttraumatic stress symptoms and cortisol slope did not mediate treatment effect on QOL. Conclusion Yoga may provide the greatest mental-health-related QOL benefits for those experiencing pre-radiotherapy sleep disturbance and depressive symptoms. Yoga may improve physical-health-related QOL by increasing ability to find benefit in the cancer experience. © The Author(s) 2016.
Validity of the Talk Test for exercise prescription after myocardial revascularization.
Zanettini, Renzo; Centeleghe, Paola; Franzelli, Cristina; Mori, Ileana; Benna, Stefania; Penati, Chiara; Sorlini, Nadia
2013-04-01
For exercise prescription, rating of perceived exertion is the subjective tool most frequently used in addition to methods based on percentage of peak exercise variables. The aim of this study was the validation of a subjective method widely called the Talk Test (TT) for optimization of training intensity in patients with recent myocardial revascularization. Fifty patients with recent myocardial revascularization (17 by coronary artery bypass grafting and 33 by percutaneous coronary intervention) were enrolled in a cardiac rehabilitation programme. Each patient underwent three repetitions of the TT during three different exercise sessions to evaluate the within-patient and between-operators reliability in assessing the workload (WL) at TT thresholds. These parameters were then compared with the data of a final cardiopulmonary exercise testing, and the WL range between the individual aerobic threshold (AeT) and anaerobic threshold (AnT) was considered as the optimal training zone. The within-patient and between-operators reliability in assessing TT thresholds were satisfactory. No significant differences were found between patients' and physiotherapists' evaluations of WL at different TT thresholds. WL at Last TT+ was between AeT and AnT in 88% of patients and slightly
Toapanta-Gaibor, N G; Suñer-Poblet, M; Cintra-Cabrera, M; Pérez-Valdivia, M Á; Suárez-Benjumea, A; Gonzalez-Roncero, F M; Bernal-Blanco, G; Rocha-Castilla, J L; Gentil-Govantes, M Á
2018-03-01
End-stage renal disease patients' access to the renal transplant (RT) waiting list (WL) depends on general criteria and their specific application in the different treatment units. Study in nonhospital hemodialysis centers (n = 9), dependent on an adult RT center. Cases included 228 patients considered to have nonactive status on the WL due to incomplete immunologic data (no blood group or HLA typing) or temporary contraindication from an incomplete pretransplant study (nonimmunologic) or comorbidity. Each individual situation was studied by reviewing the center's clinical history with the nephrologist in charge. Three situations were classified three groups. (1) Patients in this group had incomplete basic study (65 patients, 28.5%) pending cardiologic evaluation in 34%; urologic evaluation, 26%; both 18%; others, 9%; study not initiated, 12%. (2) Patients in this group had pre-existing or onset comorbidities (117 patients, 51.3%) pending studies or confirmed resolution: obesity, 30%; cancer, 17%; cardiovascular disease, 14%; digestive pathology, 10%; infection, 9%; neuropsychiatric disorders, 7%; multiple, 13%. (3) Patients in this group had other situations contraindicating RT (46 patients, 20.2%): poor therapeutic adherence, 30%; negative will of the patient, 26%; social issues, 9%; excluded by the center (not reported), 35%. We detected a high incidence of cases pending basic tests for inclusion on the WL. Obesity can be highlighted as the most frequent cause for noninclusion. Further support and coordination is required with referral hospital centers to increase and refine the RT WL. Copyright © 2017 Elsevier Inc. All rights reserved.
NASA Astrophysics Data System (ADS)
Lee, Kyoung-Sun; Imada, Shinsuke; Kyoko, Watanabe; Bamba, Yumi; Brooks, David H.
2016-10-01
An X1.6 flare occurred at the AR 12192 on 2014 October 22 at14:02 UT was observed by Hinode, IRIS, SDO, and RHESSI. We analyze a bright kernel which produces a white light (WL) flare with continuum enhancement and a hard X-ray (HXR) peak. Taking advantage of the spectroscopic observations of IRIS and Hinode/EIS, we measure the temporal variation of the plasma properties in the bright kernel in the chromosphere and corona. We found that explosive evaporation was observed when the WL emission occurred, even though the intensity enhancement in hotter lines is quite weak. The temporal correlation of the WL emission, HXR peak, and evaporation flows indicate that the WL emission was produced by accelerated electrons. To understand the white light emission processes, we calculated the deposited energy flux from the non-thermal electrons observed by RHESSI and compared it to the dissipated energy estimated from the chromospheric line (Mg II triplet) observed by IRIS. The deposited energy flux from the non-thermal electrons is about 3.1 × 1010erg cm-2 s-1 when we consider a cut-off energy 20 keV. The estimated energy flux from the temperature changes in the chromosphere measured from the Mg II subordinate line is about 4.6-6.7×109erg cm-2 s-1, ˜ 15-22% of the deposited energy. By comparison of these estimated energy fluxes we conclude that the continuum enhancement was directly produced by the non-thermal electrons.
Häkkinen, K; Mero, A; Kauhanen, H
1989-03-01
Three prebubescent athlete groups of endurance runners (E; n = 4), sprinters (S; n = 4) and weightlifters (WL; n = 4) and one control group (C; n = 6) as well as one junior but postpubescent weightlifter group (JWL; n = 6) volunteered as subjects in order to investigate specific effects of endurance, sprint and strength training on physical performance capacity during a 1 year follow-up period. The prepubescent E-group had higher (p less than 0.05) VO2 max (66.5 +/- 2.9 ml x kg1 x min-1) already at the beginning of the study than the other three groups. The prepubescent WL-group demonstrated greater (p less than 0.05) maximal muscular strength than the E-group and the WL-group increased its strength greatly by 21.4% (p less than 0.05) during the follow-up. No significant differences were observed in physical performance capacity between the prepubescent WL- and S-groups. Both groups demonstrated a slightly (ns.) better force-time curve recorded from the leg extensor muscles than the E-group and significant (p less than 0.05) increases occurred in these two groups in dynamic explosive performance during the follow-up. The postpubescent JWL-group demonstrated much greater (p less than 0.001) muscular mass and maximal strength than the prepubescent groups. No significant changes occurred in explosive types of performances in these athletes but significant (p less than 0.05) increase took place in the maximal neural activation and strength of the leg extensor muscles during the 1 year.(ABSTRACT TRUNCATED AT 250 WORDS)
LoCuSS: THE SUNYAEV-ZEL'DOVICH EFFECT AND WEAK-LENSING MASS SCALING RELATION
DOE Office of Scientific and Technical Information (OSTI.GOV)
Marrone, Daniel P.; Carlstrom, John E.; Gralla, Megan
2012-08-01
We present the first weak-lensing-based scaling relation between galaxy cluster mass, M{sub WL}, and integrated Compton parameter Y{sub sph}. Observations of 18 galaxy clusters at z {approx_equal} 0.2 were obtained with the Subaru 8.2 m telescope and the Sunyaev-Zel'dovich Array. The M{sub WL}-Y{sub sph} scaling relations, measured at {Delta} = 500, 1000, and 2500 {rho}{sub c}, are consistent in slope and normalization with previous results derived under the assumption of hydrostatic equilibrium (HSE). We find an intrinsic scatter in M{sub WL} at fixed Y{sub sph} of 20%, larger than both previous measurements of M{sub HSE}-Y{sub sph} scatter as well asmore » the scatter in true mass at fixed Y{sub sph} found in simulations. Moreover, the scatter in our lensing-based scaling relations is morphology dependent, with 30%-40% larger M{sub WL} for undisturbed compared to disturbed clusters at the same Y{sub sph} at r{sub 500}. Further examination suggests that the segregation may be explained by the inability of our spherical lens models to faithfully describe the three-dimensional structure of the clusters, in particular, the structure along the line of sight. We find that the ellipticity of the brightest cluster galaxy, a proxy for halo orientation, correlates well with the offset in mass from the mean scaling relation, which supports this picture. This provides empirical evidence that line-of-sight projection effects are an important systematic uncertainty in lensing-based scaling relations.« less
High-level conversion of L-lysine into 5-aminovalerate that can be used for nylon 6,5 synthesis.
Park, Si Jae; Oh, Young Hoon; Noh, Won; Kim, Hye Young; Shin, Jae Ho; Lee, Eun Gyo; Lee, Seungwoon; David, Yokimiko; Baylon, Mary Grace; Song, Bong Keun; Jegal, Jonggeon; Lee, Sang Yup; Lee, Seung Hwan
2014-10-01
L-Lysine is a potential feedstock for the production of bio-based precursors for engineering plastics. In this study, we developed a microbial process for high-level conversion of L-lysine into 5-aminovalerate (5AVA) that can be used as a monomer in nylon 6,5 synthesis. Recombinant Escherichia coli WL3110 strain expressing Pseudomonas putida delta-aminovaleramidase (DavA) and lysine 2-monooxygenase (DavB) was grown to high density in fed-batch culture and used as a whole cell catalyst. High-density E. coli WL3110 expressing DavAB, grown to an optical density at 600 nm (OD600 ) of 30, yielded 36.51 g/L 5AVA from 60 g/L L-lysine in 24 h. Doubling the cell density of E. coli WL3110 improved the conversion yield to 47.96 g/L 5AVA from 60 g/L of L-lysine in 24 h. 5AVA production was further improved by doubling the L-lysine concentration from 60 to 120 g/L. The highest 5AVA titer (90.59 g/L; molar yield 0.942) was obtained from 120 g/L L-lysine by E. coli WL3110 cells grown to OD600 of 60. Finally, nylon 6,5 was synthesized by bulk polymerization of ϵ-caprolactam and δ-valerolactam prepared from microbially synthesized 5AVA. The hybrid system demonstrated here has promising possibilities for application in the development of industrial bio-nylon production processes. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Glass science tutorial: Lecture No. 7, Waste glass technology for Hanford
DOE Office of Scientific and Technical Information (OSTI.GOV)
Kruger, A.A.
1995-07-01
This paper presents the details of the waste glass tutorial session that was held to promote knowledge of waste glass technology and how this can be used at the Hanford Reservation. Topics discussed include: glass properties; statistical approach to glass development; processing properties of nuclear waste glass; glass composition and the effects of composition on durability; model comparisons of free energy of hydration; LLW glass structure; glass crystallization; amorphous phase separation; corrosion of refractories and electrodes in waste glass melters; and glass formulation for maximum waste loading.
Assessment of microwave-based clinical waste decontamination unit.
Hoffman, P N; Hanley, M J
1994-12-01
A clinical waste decontamination unit that used microwave-generated heat was assessed for operator safety and efficacy. Tests with loads artificially contaminated with aerosol-forming particles showed that no particles were detected outside the machine provided the seals and covers were correctly seated. Thermometric measurement of a self-generated steam decontamination cycle was used to determine the parameters needed to ensure heat disinfection of the waste reception hopper, prior to entry for maintenance or repair. Bacterial and thermometric test pieces were passed through the machine within a full load of clinical waste. These test pieces, designed to represent a worst case situation, were enclosed in aluminium foil to shield them from direct microwave energy. None of the 100 bacterial test pieces yielded growth on culture and all 100 thermal test pieces achieved temperatures in excess of 99 degrees C during their passage through the decontamination unit. It was concluded that this method may be used to render safe the bulk of of ward-generated clinical waste.
Weck, Florian; Neng, Julia M B; Schwind, Julia; Höfling, Volkmar
2015-08-01
Dysfunctional evaluations of somatic symptoms are considered a central factor in maintaining hypochondriasis. The aim of the current study was to investigate whether exposure therapy (ET) without cognitive restructuring is sufficient to change dysfunctional evaluations of somatic symptoms. The current study was based on a randomized controlled trial and compared patients with hypochondriasis (N=73) receiving ET or cognitive therapy (CT) to a wait list (WL) control group. In both the ET and CT groups, dysfunctional symptom evaluations changed significantly compared with the WL group. No differences between the ET and CT groups emerged. The relationship between the treatment condition (active treatment vs. WL) and reductions in health anxiety was mediated by changes in somatic symptom evaluations only in a specific card sorting procedure. We conclude that addressing dysfunctional symptom evaluations is a necessary precondition for the effective treatment of hypochondriasis. However, the results indicate that ET and CT appear to change those processes to a similar degree. Copyright © 2015 Elsevier Ltd. All rights reserved.
Effect of yoga on musculoskeletal discomfort and motor functions in professional computer users.
Telles, Shirley; Dash, Manoj; Naveen, K V
2009-01-01
The self-rated musculoskeletal discomfort, hand grip strength, tapping speed, and low back and hamstring flexibility (based on a sit and reach task) were assessed in 291 professional computer users. They were then randomized as Yoga (YG; n=146) and Wait-list control (WL; n=145) groups. Follow-up assessments for both groups were after 60 days during which the YG group practiced yoga for 60 minutes daily, for 5 days in a week. The WL group spent the same time in their usual recreational activities. At the end of 60 days, the YG group (n=62) showed a significant decrease in the frequency, intensity and degree of interference due to musculoskeletal discomfort, an increase in bilateral hand grip strength, the right hand tapping speed, and low back and hamstring flexibility (repeated measures ANOVA and post hoc analysis with Bonferroni adjustment). In contrast, the WL group (n=56) showed an increase in musculoskeletal discomfort and a decrease in left hand tapping speed. The results suggest that yoga practice is a useful addition to the routine of professional computer users.
Anti-inflammatory effects of phenolic crude extracts from five fractions of Corchorus Olitorius L.
Yan, Yeong-Yu; Wang, Yue-Wen; Chen, Su-Lin; Zhuang, Shu-Ru; Wang, Chin-Kun
2013-06-01
Corchorus olitorius L. is grown in Taiwan during summer. Tender leaves are crushed and washed by running water before eating. Five fractions including crude phenolic extracts (using 80 per cent aqueous acetone) of whole plant, leaf, stem, washed leaf (WL) and dried water washing material (WW) were used in this study. Linoleic acid autoxidation inhibitions on all fractions were higher than that on α-tocopherol. Except for WL and WW, other fractions also showed DPPH radical scavenging efficiency. The effect of all fractions on the regulation of inflammatory responses in lipopolysaccharide (LPS)-stimulated J774A.1 macrophage cells was investigated. All fractions diminished LPS-induced protein expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase 2 (COX-2). Nitric oxide (NO) and prostaglandin E2 (PGE(2)), downstream products, were also suppressed in dose-dependent manners, except for WL and WW. Oxidative modification and loss of leaf phenolics after kneading and washing greatly affected DPPH radical scavenging and inflammatory responses. Copyright © 2012 Elsevier Ltd. All rights reserved.
Space disposal of nuclear wastes
NASA Technical Reports Server (NTRS)
Priest, C. C.; Nixon, R. F.; Rice, E. E.
1980-01-01
The DOE has been studying several options for nuclear waste disposal, among them space disposal, which NASA has been assessing. Attention is given to space disposal destinations noting that a circular heliocentric orbit about halfway between Earth and Venus is the reference option in space disposal studies. Discussion also covers the waste form, showing that parameters to be considered include high waste loading, high thermal conductivity, thermochemical stability, resistance to leaching, fabrication, resistance to oxidation and to thermal shock. Finally, the Space Shuttle nuclear waste disposal mission profile is presented.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Smith, M. E.; Jones, T. M.; Miller, D. H.
Several Slurry-Fed Melt Rate Furnace (SMRF) tests with earlier projections of the Sludge Batch 4 (SB4) composition have been performed.1,2 The first SB4 SMRF test used Frits 418 and 320, however it was found after the test that the REDuction/OXidation (REDOX) correlation at that time did not have the proper oxidation state for manganese. Because the manganese level in the SB4 sludge was higher than previous sludge batches tested, the impact of the higher manganese oxidation state was greater. The glasses were highly oxidized and very foamy, and therefore the results were inconclusive. After resolving this REDOX issue, Frits 418,more » 425, and 503 were tested in the SMRF with the updated baseline SB4 projection. Based on dry-fed Melt Rate Furnace (MRF) tests and the above mentioned SMRF tests, two previous frit recommendations were made by the Savannah River National Laboratory (SRNL) for processing of SB4 in the Defense Waste Processing Facility (DWPF). The first was Frit 503 based on the June 2006 composition projections.3 The recommendation was changed to Frit 418 as a result of the October 2006 composition projections (after the Tank 40 decant was implemented as part of the preparation plan). However, the start of SB4 processing was delayed due to the control room consolidation outage and the repair of the valve box in the Tank 51 to Tank 40 transfer line. These delays resulted in changes to the projected SB4 composition. Due to the slight change in composition and based on preliminary dry-fed MRF testing, SRNL believed that Frit 510 would increase throughput in processing SB4 in DWPF. Frit 418, which was used in processing Sludge Batch 3 (SB3), was a viable candidate and available in DWPF. Therefore, it was used during the initial SB4 processing. Due to the potential for higher melt rates with Frit 510, SMRF tests with the latest SB4 composition (1298 canisters) and Frits 510 and 418 were performed at a targeted waste loading (WL) of 35%. The '1298 canisters' describes the number of equivalent canisters that would be produced from the beginning of the current contract period before SB3 is blended with SB4. The melt rate for the SMRF SB4/Frit 510 test was 14.6 grams/minute. Due to cold cap mounding problems with the SMRF SB4/Frit 418 feed at 50 weight % solids that prevented a melt rate determination, this feed was diluted to 45 weight % solids. The melt rate for this diluted feed was 8.9 grams/minute. A correction factor of 1.2 for estimating the melt rate at 50 weight % solids from 45 weight % solids test results (based on previous SMRF testing5) was then used to estimate a melt rate of 10.7 grams/minute for SB4/Frit 418 at 50 weight % solids. Therefore, the use of Frit 510 versus Frit 418 with SB4 resulted in a higher melt rate (14.6 versus an estimated 10.7 grams/minute). For reference, a previous SMRF test with SB3/Frit 418 feed at 35% waste loading and 50 weight % solids resulted in a melt rate of 14.1 grams/minute. Therefore, depending on the actual feed rheology, the use of Frit 510 with SB4 could result in similar melt rates as experienced with SB3/Frit 418 feed in the DWPF.« less
Thermal Analysis for Ion-Exchange Column System
DOE Office of Scientific and Technical Information (OSTI.GOV)
Lee, Si Y.; King, William D.
2012-12-20
Models have been developed to simulate the thermal characteristics of crystalline silicotitanate ion exchange media fully loaded with radioactive cesium either in a column configuration or distributed within a waste storage tank. This work was conducted to support the design and operation of a waste treatment process focused on treating dissolved, high-sodium salt waste solutions for the removal of specific radionuclides. The ion exchange column will be installed inside a high level waste storage tank at the Savannah River Site. After cesium loading, the ion exchange media may be transferred to the waste tank floor for interim storage. Models weremore » used to predict temperature profiles in these areas of the system where the cesium-loaded media is expected to lead to localized regions of elevated temperature due to radiolytic decay. Normal operating conditions and accident scenarios (including loss of solution flow, inadvertent drainage, and loss of active cooling) were evaluated for the ion exchange column using bounding conditions to establish the design safety basis. The modeling results demonstrate that the baseline design using one central and four outer cooling tubes provides a highly efficient cooling mechanism for reducing the maximum column temperature. In-tank modeling results revealed that an idealized hemispherical mound shape leads to the highest tank floor temperatures. In contrast, even large volumes of CST distributed in a flat layer with a cylindrical shape do not result in significant floor heating.« less
Performance assessment of two-stage anaerobic digestion of kitchen wastes.
Bo, Zhang; Pin-Jing, He
2014-01-01
This study is aimed at investigating the performance of the two-phase anaerobic digestion of kitchen wastes in a lab-scale setup. The semi-continuous experiment showed that the two-phase anaerobic digestion of kitchen wastes had a bioconversion rate of 83%, biogas yield of 338 mL x (g chemical oxygen demand (COD))(-1) and total solid conversion of 63% when the entire two-phase anaerobic digestion process was subjected to an organic loading rate (OLR) of 10.7 g x (L d)(-1). In the hydrolysis-acidogenesis process, the efficiency of solubilization decreased from 72.6% to 41.1%, and the acidogenesis efficiency decreased from 31.8% to 17.8% with an increase in the COD loading rate. On the other hand, the performance of the subsequent methanogenic process was not susceptible to the increase in the feeding COD loading rate in the hydrolysis-acidogenesis stage. Lactic acid was one of the main fermentation products, accounting for over 40% of the total soluble COD in the fermentation liquid. The batch experiments indicated that the lactic acid was the earliest predominant fermentation product, and distributions of fermentation products were pH dependent. Results showed that increasing the feeding OLR of kitchen wastes made the two-stage anaerobic digestion process more effective. Moreover, there was a potential improvement in the performance of anaerobic digestion of kitchen wastes with a corresponding improvement in the hydrolysis process.
2005-12-01
available in local home centers. For termite and other infestations, the BOP contacts the U.S. Air Force for treatment. For such materials, the BOP...property. These include 80k85, 8SR44, 8Wl13 and 8Wll4. Moore (1901, 1918) visited these sites, all of which were listed as mounds on the original...site forms. 80k85 (formerly 8Wl12)1 was a circular mound , 2.5ft in height and 35ft in diameter (Moore 1918:531 ). 1 Moore found no trace of burials
Integration of Statistical and Physical Models of Short Fatigue Crack Growth.
1987-02-01
M.R. James and B.N. Cox, *Fundamental Characterization of Surface Microplasticity ," Final Report on NSF Grant No. DMR-8310652, July 1986. 23. W.L...Dec. 1985. 24. W.L. Morris, B.N. Cox and M.R. James, " Microplastic Deformation of Al 2219- T85 I," to be published in Acta Metall. 25. B.N. Cox, W.L...Morris and M.R. James, "Two-Stage Microplastic Surface Defor- mation in Al 2219-T851," to be published in Acta Metall. 26. W.L. Morris, M.R. James and
7. VIEW SOUTHEAST, SHOWING WEST SIDE FROM LAND, WITH WASTE ...
7. VIEW SOUTHEAST, SHOWING WEST SIDE FROM LAND, WITH WASTE PAPER BUNDLED ON DOCK, AWAITING LOADING ONTO ODIGITRIA B - Connecticut State Pier, State Pier Road at Thames River, New London, New London County, CT
NASA Astrophysics Data System (ADS)
Stefanovsky, S. V.; Stefanovsky, O. I.; Kadyko, M. I.; Nikonov, B. S.
2018-03-01
Sodium aluminum (iron) phosphate glass ceramics containing of up to 20 wt.% rare earth (RE) oxides simulating pyroprocessing waste were produced by melting at 1250 °C followed by either quenching or slow cooling to room temperature. The iron-free glass-ceramics were composed of major glass and minor phosphotridymite and monazite. The iron-bearing glass-ceramics were composed of major glass and minor monazite and Na-Al-Fe orthophosphate at low waste loadings (5-10 wt.%) and major orthophosphate and minor monazite as well as interstitial glass at high waste loadings (15-20 wt.%). Slowly cooled samples contained higher amount of crystalline phases than quenched ones. Monazite is major phase for REs. Leach rates from the materials of major elements (Na, Al, Fe, P) are 10-5-10-7 g cm-2 d-1, RE elements - lower than 10-5 g cm-2 d-1.
40 CFR 60.58b - Compliance and performance testing.
Code of Federal Regulations, 2010 CFR
2010-07-01
... demonstrated municipal waste combustor unit load shall be the highest 4-hour arithmetic average load achieved... shall be the highest 4-hour arithmetic average temperature achieved at the particulate matter control...
Waste Load Allocation for Conservative Substances to Protect Aquatic Organisms
NASA Astrophysics Data System (ADS)
Hutcheson, M. R.
1992-01-01
A waste load allocation process is developed to determine the maximum effluent concentration of a conservative substance that will not harm fish and wildlife propagation. If this concentration is not exceeded in the effluent, the acute toxicity criterion will not be violated in the receiving stream, and the chronic criterion will not be exceeded in the zone of passage, defined in many state water quality standards to allow the movement of aquatic organisms past a discharge. Considerable simplification of the concentration equation, which is the heart of any waste load allocation, is achieved because it is based on the concentration in the receiving stream when the concentration gradient on the zone of passage boundary is zero. Consequently, the expression obtained for effluent concentration is independent of source location or stream morphology. Only five independent variables, which are routinely available to regulatory agencies, are required to perform this allocation. It aids in developing permit limits which are protective without being unduly restrictive or requiring large expenditures of money and manpower on field investigations.
NASA Astrophysics Data System (ADS)
Wibowo, Agus Tri; Handayani, Naniek Utami
2017-11-01
Petrokimia Gresik is one of the largest fertilizer producer in Indonesia which has a cross-country network of supply chain and distribution throughout the archipelago, either in bulk fertilizer or in bag fertilizer. This research was conducted at PT. PG port which is the main point of the logistics activities in the firm itself, either loading or unloading. This research focus on the process of loading the in bag fertilizer. Problems that occur in this process are due to the inefficiency of the flow of the Supply Chain, caused by the presence of waste and non-value-added activities. The purpose of this study was to determine what kind of waste that occurs during the process, as well as suggestions for improvements using the concept of Lean Supply Chain and Value Stream Mapping, and look for the cause of the problem using the 5 Whys method. The most influential types of waste during the process stream is Waiting Time (20.42%), and Non-Value Added activies of 51.9%. By using 5Whys, the largest cause of waste found are the length of the truck waiting for the cargo, numbers of crane are already inproper, and the absence of the scheduling and charge allocation. Recommended solutions are scheduling and allocation, creation of special line in the warehouse, and supplying cranes with appropriate load speed. Based on improvement suggestions, total NVA predicted to be reduced to 59.8%.
Femtosecond Visible Transient Absorption Spectroscopy of Chlorophyll f-Containing Photosystem I.
Kaucikas, Marius; Nürnberg, Dennis; Dorlhiac, Gabriel; Rutherford, A William; van Thor, Jasper J
2017-01-24
Photosystem I (PSI) from Chroococcidiopsis thermalis PCC 7203 grown under far-red light (FRL; >725 nm) contains both chlorophyll a and a small proportion of chlorophyll f. Here, we investigated excitation energy transfer and charge separation using this FRL-grown form of PSI (FRL-PSI). We compared femtosecond transient visible absorption changes of normal, white-light (WL)-grown PSI (WL-PSI) with those of FRL-PSI using excitation at 670 nm, 700 nm, and (in the case of FRL-PSI) 740 nm. The possibility that chlorophyll f participates in energy transfer or charge separation is discussed on the basis of spectral assignments. With selective pumping of chlorophyll f at 740 nm, we observe a final ∼150 ps decay assigned to trapping by charge separation, and the amplitude of the resulting P700 +• A 1 -• charge-separated state indicates that the yield is directly comparable to that of WL-PSI. The kinetics shows a rapid 2 ps time constant for almost complete transfer to chlorophyll f if chlorophyll a is pumped with a wavelength of 670 nm or 700 nm. Although the physical role of chlorophyll f is best supported as a low-energy radiative trap, the physical location should be close to or potentially within the charge-separating pigments to allow efficient transfer for charge separation on the 150 ps timescale. Target models can be developed that include a branching in the formation of the charge separation for either WL-PSI or FRL-PSI. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.
Roberts, Michael D.; Company, Joseph M.; Brown, Jacob D.; Toedebusch, Ryan G.; Padilla, Jaume; Jenkins, Nathan T.; Laughlin, M. Harold
2012-01-01
According to the latest data from the Center for Disease Control and Prevention 17%, or 12.5 million, of children and adolescents aged 2–19 years in the United States are obese. Physical inactivity is designated as one of the actual causes of US deaths and undoubtedly contributes to the obesity epidemic in children and adults. Examining the effects of inactivity on physiological homeostasis during youth is crucial given that 58% of children between the ages 6–11 yr old fail to obtain the recommended 60 min/day of physical activity and 92% of adolescents fail to achieve this goal [Troiano et al. Med Sci Sports Exerc. 40, 2008]. Nonetheless, invasive mechanistic studies in children linking diminished physical activity with metabolic maladies are lacking for obvious ethical reasons. The rodent wheel lock (WL) model was adopted by our laboratory and others to study how different organ systems of juvenile rats respond to a cessation of daily physical activity. Our WL model houses rats in cages equipped with voluntary running wheels starting at 28 days of age. After a certain period of voluntary running (3 to 6 wk), the wheels are locked, thus preventing the rats' primary source of physical activity. The studies discussed herein suggest that obesity-associated maladies including skeletal muscle insulin resistance, hypothalamic leptin resistance, fatty acid oxidation impairments in skeletal muscle and adipose tissue, nonalcoholic fatty liver disease, and endothelial dysfunction are initiated in juvenile animals that are restrained from voluntary exercise via WL. The use of the juvenile rodent WL or other inactivity models will continue to provide a powerful clinical translational tool that can be used for primordial prevention of human childhood obesity. PMID:22696577
Femoral rotational asymmetry is a common anatomical variant.
Newman, Christopher R; Walter, William L; Talbot, Simon
2018-05-01
The sulcus line (SL) is a three-dimensional landmark that corrects for individual variation in the coronal alignment of the trochlear groove in contrast to the traditional Whiteside's line (WL). Femoral rotational asymmetry (FRA) is an anatomical variation in which the posterior condyles and trochlear groove are not perpendicular to each other. This study aims to measure the SL and assess its reliability relative to WL, in addition to measuring and classifying the FRA. A retrospective analysis of a series of 191 CT scans of nonarthritic knees was performed. Measurements were taken of rotational landmarks in three-dimensional reconstructions. The variability and outlier rate of SL was less than WL (P < 0.05), however, it was also greater than the posterior condylar line (PC) (P < 0.05). Averaging the PC + 3° and the SL did not change the rate of femoral malrotation relative to the surgical epicondylar axis (SEA) (P > 0.05), however it decreased the rate of change of the rotational alignment of the trochlear groove between the native knee and the prosthetic knee from 31% to 5% (P < 0.05). FRA was classified and was >5° in 56/191 (29%) of cases. The SL technique is more accurate than WL for determining the rotational alignment of the trochlear groove. Nonarthritic femora have a high rate of rotational asymmetry. Identifying and classifying FRA in individual cases allows the femoral component to be inserted in a position which gives the best possible match to both the native posterior condyles and trochlear groove. Clin. Anat. 31:551-559, 2018. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.
Algorithm for prioritization of patients on the waiting list for liver transplantation.
Gambato, M; Senzolo, M; Canova, D; Germani, G; Tomat, S; Masier, A; Russo, F P; Perissinotto, E; Zanus, G; Cillo, U; Burra, P
2007-01-01
Prioritization of patients on the waiting list (WL) for OLT is still a critical issue. Numerous models have been developed to predict mortality before and after OLT. The aim of the study was to prospectively evaluate cirrhotics with and without hepatocellular carcinoma (HCC) undergoing orthotopic liver transplantation (OLT) severity of liver disease on the WL and at transplant, mortality on the WL and after OLT, and their correlations. An algorithm based on seven patient variables (MELD, CTP, UNOS, HCC, BMI, waiting time, age) was created by software dedicated to prioritize patients on the waiting list. We evaluated 118 patients including 75 men and 43 women of age range 19 to 66 years, who underwent OLT from July 2004 to June 2006. Mean CTP and MELD at listing were 8.44 (range 6-12) and 13 (range 2-24), respectively. Overall mortality on the WL at 24 months was 13%, which was significantly higher among patients with MELD > 25 compared to patients with MELD 0 to 15 (P < .0001) or MELD 16 to 25 (P = .0007) at listing. Mean MELD at OLT was 15 (range 7-36), which was significantly lower in patients with than without HCC (MELD 12 vs 16; P = .0003). Six hundred-day patient survival was significantly lower among patients with MELD > 25 compared to patients with MELD < 25 at OLT (P = .017), whereas no difference in survival was observed between patients with and without HCC. The sickest patients are characterized by high mortality both on the waiting list and after liver transplantation. Patients with HCC are transplanted in better condition compared to patients without HCC with the same survival.
Ebrahim, Aqeel Khalil; Wadachi, Reiko; Suda, Hideaki
2007-04-01
The aim of this study was to evaluate the accuracy of five electronic apex locators (EALs) in determining the working length (WL) of teeth after removal of the root canal obturation materials. A total of 32 extracted straight, single-rooted teeth were used. The actual canal length (AL) was determined and the WL was established by subtracting 0.5 mm from the AL. The root canals were instrumented and divided into two groups. One group (n = 6) served as control, while the other group (n = 26) was the experimental group. In the experimental group, the root canals were obturated using vertically compacted gutta-percha with AH 26 sealer. In both groups, the access cavities were restored with a provisional restoration and stored for 15 days at 37 degrees C and 100% humidity. The root canal obturation material was removed, and the teeth were then mounted in an experimental apparatus. Five EALs were used: Dentaport ZX, ProPex, Foramatron D10, Apex NRG and Apit 7. For the electronic measurement of canal length, a size 25 K-file was used. During measurement, the canal was irrigated with 2.5% sodium hypochlorite. The difference (D) between the AL and the electronically determined length (EDL), AL-EDL, was calculated and recorded for each measurement. Data were analysed by two-way anova and Fisher's PLSD test. In both groups, statistically significant differences were found among the EALs (P < 0.01). In conclusion, the Dentaport ZX, ProPex and Foramatron D10 were more accurate than the other two EALs in determining the WL in teeth after removal of the root canal obturation materials. However, the Apex NRG and Apit 7 were also reliable for determination of the WL in the majority of the cases.
Optimized detection of shear peaks in weak lensing maps
NASA Astrophysics Data System (ADS)
Marian, Laura; Smith, Robert E.; Hilbert, Stefan; Schneider, Peter
2012-06-01
We present a new method to extract cosmological constraints from weak lensing (WL) peak counts, which we denote as ‘the hierarchical algorithm’. The idea of this method is to combine information from WL maps sequentially smoothed with a series of filters of different size, from the largest down to the smallest, thus increasing the cosmological sensitivity of the resulting peak function. We compare the cosmological constraints resulting from the peak abundance measured in this way and the abundance obtained by using a filter of fixed size, which is the standard practice in WL peak studies. For this purpose, we employ a large set of WL maps generated by ray tracing through N-body simulations, and the Fisher matrix formalism. We find that if low signal-to-noise ratio (?) peaks are included in the analysis (?), the hierarchical method yields constraints significantly better than the single-sized filtering. For a large future survey such as Euclid or Large Synoptic Survey Telescope, combined with information from a cosmic microwave background experiment like Planck, the results for the hierarchical (single-sized) method are Δns= 0.0039 (0.004), ΔΩm= 0.002 (0.0045), Δσ8= 0.003 (0.006) and Δw= 0.019 (0.0525). This forecast is conservative, as we assume no knowledge of the redshifts of the lenses, and consider a single broad bin for the redshifts of the sources. If only peaks with ? are considered, then there is little difference between the results of the two methods. We also examine the statistical properties of the hierarchical peak function: Its covariance matrix has off-diagonal terms for bins with ? and aperture mass of M < 3 × 1014 h-1 M⊙, the higher bins being largely uncorrelated and therefore well described by a Poisson distribution.
DOE Office of Scientific and Technical Information (OSTI.GOV)
F. Cui; F.J. Presuel-Moreno; R.G. Kelly
2005-10-13
The ability of a SS316L surface wetted with a thin electrolyte layer to serve as an effective cathode for an active localized corrosion site was studied computationally. The dependence of the total net cathodic current, I{sub net}, supplied at the repassivation potential E{sub rp} (of the anodic crevice) on relevant physical parameters including water layer thickness (WL), chloride concentration ([Cl{sup -}]) and length of cathode (Lc) were investigated using a three-level, full factorial design. The effects of kinetic parameters including the exchange current density (i{sub o,c}) and Tafel slope ({beta}{sub c}) of oxygen reduction, the anodic passive current density (i{submore » p}) (on the cathodic surface), and E{sub rp} were studied as well using three-level full factorial designs of [Cl{sup -}] and Lc with a fixed WL of 25 {micro}m. The study found that all the three parameters WL, [Cl{sup -}] and Lc as well as the interactions of Lc x WL and Lc x [Cl{sup -}] had significant impact on I{sub net}. A five-factor regression equation was obtained which fits the computation results reasonably well, but demonstrated that interactions are more complicated than can be explained with a simple linear model. Significant effects on I{sub net} were found upon varying either i{sub o,c}, {beta}{sub c}, or E{sub rp}, whereas i{sub p} in the studied range was found to have little impact. It was observed that I{sub net} asymptotically approached maximum values (I{sub max}) when Lc increased to critical minimum values. I{sub max} can be used to determine the stability of coupled localized corrosion and the critical Lc provides important information for experimental design and corrosion protection.« less
A Lactate Kinetics Method for Assessing the Maximal Lactate Steady State Workload
Hering, Gernot O.; Hennig, Ewald M.; Riehle, Hartmut J.; Stepan, Jens
2018-01-01
During a continuously increasing exercise workload (WL) a point will be reached at which arterial lactate accumulates rapidly. This so-called lactate threshold (LT) is associated with the maximal lactate steady state workload (MLSSW), the highest WL, at which arterial lactate concentration [LA] does not change. However, the physiological range in which the LT and the MLSSW occur has not been demonstrated directly. We used minor WL variations in the MLSSW range to assess arterial lactate kinetics in 278 treadmill and 148 bicycle ergometer exercise tests. At a certain workload, minimal further increment of running speed (0.1–0.15 m/s) or cycling power (7–10 W) caused a steep elevation of [LA] (0.9 ± 0.43 mM, maximum increase 2.4 mM), indicating LT achievement. This sharp [LA] increase was more pronounced when higher WL increments were used (0.1 vs. 0.30 m/s, P = 0.02; 0.15 vs. 0.30 m/s, P < 0.001; 7 vs. 15 W, P = 0.002; 10 vs. 15 W, P = 0.001). A subsequent workload reduction (0.1 m/s/7 W) stopped the [LA] increase indicating MLSSW realization. LT based determination of running speed (MLSSW) was highly reproducible on a day-to-day basis (r = 0.996, P < 0.001), valid in a 10 km constant velocity setting (r = 0.981, P < 0.001) and a half marathon race (r = 0.969, P < 0.001). These results demonstrate a fine-tuned regulation of exercise-related lactate metabolism, which can be reliably captured by assessing lactate kinetics at the MLSSW. PMID:29651253
Garvey, W. Timothy; Greenway, Frank L.; Zhou, Sharon; Fain, Randi; Pilson, Robert; Fujioka, Ken; Aronne, Louis J.
2017-01-01
Objective To assess the short‐term tolerability of lorcaserin alone or with two dose regimens of phentermine. Methods This was a 12‐week, randomized, double‐blind, pilot safety study of N = 238 nondiabetic patients with obesity or overweight with ≥1 comorbidity randomized to lorcaserin 10 mg twice daily (BID; LOR BID) alone or with phentermine 15 mg once daily (QD; LOR BID+PHEN QD) or 15 mg twice daily (LOR BID+PHEN BID). Patients reporting ≥ 1 of 9 potentially serotonergic adverse events (AEs), mean weight loss (WL), and ≥5% WL are reported. Results N = 238 were randomized, and N = 235 were treated. N = 94 reported potentially serotonergic AEs: 37.2% LOR BID, 42.3% LOR BID+PHEN QD, and 40.5% LOR BID+PHEN BID. AEs leading to discontinuation were reported approximately twice as often in the LOR BID+PHEN BID group versus the LOR BID group. Mean WL was 3.5 kg/3.3%, 7.0 kg/6.7%, and 7.6 kg/7.2% for LOR BID, LOR BID+PHEN QD, and LOR BID+PHEN BID, respectively. At least 5% WL was achieved by 28.2% LOR BID, 59.0% LOR BID+PHEN QD (P = 0.0002 vs. LOR BID), and 70.9% LOR BID+PHEN BID (P < 0.0001 vs. LOR BID) patients. Conclusions Phentermine added to lorcaserin enhanced short‐term weight loss but did not increase incidence of potentially serotonergic AEs; however, phentermine twice daily increased discontinuation compared to both lorcaserin alone and lorcaserin plus phentermine once daily. PMID:28440045
Smith, Steven R; Garvey, W Timothy; Greenway, Frank L; Zhou, Sharon; Fain, Randi; Pilson, Robert; Fujioka, Ken; Aronne, Louis J
2017-05-01
To assess the short-term tolerability of lorcaserin alone or with two dose regimens of phentermine. This was a 12-week, randomized, double-blind, pilot safety study of N = 238 nondiabetic patients with obesity or overweight with ≥1 comorbidity randomized to lorcaserin 10 mg twice daily (BID; LOR BID) alone or with phentermine 15 mg once daily (QD; LOR BID+PHEN QD) or 15 mg twice daily (LOR BID+PHEN BID). Patients reporting ≥ 1 of 9 potentially serotonergic adverse events (AEs), mean weight loss (WL), and ≥5% WL are reported. N = 238 were randomized, and N = 235 were treated. N = 94 reported potentially serotonergic AEs: 37.2% LOR BID, 42.3% LOR BID+PHEN QD, and 40.5% LOR BID+PHEN BID. AEs leading to discontinuation were reported approximately twice as often in the LOR BID+PHEN BID group versus the LOR BID group. Mean WL was 3.5 kg/3.3%, 7.0 kg/6.7%, and 7.6 kg/7.2% for LOR BID, LOR BID+PHEN QD, and LOR BID+PHEN BID, respectively. At least 5% WL was achieved by 28.2% LOR BID, 59.0% LOR BID+PHEN QD (P = 0.0002 vs. LOR BID), and 70.9% LOR BID+PHEN BID (P < 0.0001 vs. LOR BID) patients. Phentermine added to lorcaserin enhanced short-term weight loss but did not increase incidence of potentially serotonergic AEs; however, phentermine twice daily increased discontinuation compared to both lorcaserin alone and lorcaserin plus phentermine once daily. © 2017 The Authors. Obesity published by Wiley Periodicals, Inc. on behalf of The Obesity Society (TOS).
Impact of needle insertion depth on the removal of hard-tissue debris.
Perez, R; Neves, A A; Belladonna, F G; Silva, E J N L; Souza, E M; Fidel, S; Versiani, M A; Lima, I; Carvalho, C; De-Deus, G
2017-06-01
To evaluate the effect of depth of insertion of an irrigation needle tip on the removal of hard-tissue debris using micro-computed tomographic (micro-CT) imaging. Twenty isthmus-containing mesial roots of mandibular molars were anatomically matched based on similar morphological dimensions using micro-CT evaluation and assigned to two groups (n = 10), according to the depth of the irrigation needle tip during biomechanical preparation: 1 or 5 mm short of the working length (WL). The preparation was performed with Reciproc R25 file (tip size 25, .08 taper) and 5.25% NaOCl as irrigant. The final rinse was 17% EDTA followed by bidistilled water. Then, specimens were scanned again, and the matched images of the canals, before and after preparation, were examined to quantify the amount of hard-tissue debris, expressed as the percentage volume of the initial root canal volume. Data were compared statistically using the Mann-Whitney U-test. None of the tested needle insertion depths yielded root canals completely free from hard-tissue debris. The insertion depth exerted a significant influence on debris removal, with a significant reduction in the percentage volume of hard-tissue debris when the needle was inserted 1 mm short of the WL (P < 0.05). The insertion depth of irrigation needles significantly influenced the removal of hard-tissue debris. A needle tip positioned 1 mm short of the WL resulted in percentage levels of hard-tissue debris removal almost three times higher than when positioned 5 mm from the WL. © 2016 International Endodontic Journal. Published by John Wiley & Sons Ltd.
Tennert, Christian; Herbert, Josef; Altenburger, Markus Jörg; Wrbas, Karl-Thomas
2010-10-01
An exact determination of the apical root canal diameter is crucial for correct cleaning and shaping of a root canal. The aim of this study was to investigate the discrepancies of the initial apical root canal diameter and the diameter that is measured by the initial apical file (IAF) after cervical flaring using current rotary nickel-titanium systems. Mesiobuccal canals of 40 extracted mandibular molars were randomly assigned to four groups. In the first group, root canals were not flared. Root canals of the other groups were preflared using FlexMaster (VDW, Munich, Germany), ProTaper (Dentsply, Konstanz, Germany), or RaCe (FKG Dentaire, Genf, Switzerland) instruments. The tooth length was determined by inserting an ISO 06 K-file to the apical foramen. The working length (WL) was set 1 mm short of the apical foramen. File sizes were increased after binding sensation was felt at the WL. Transversal sections of the WL regions were examined under stereomicroscope, and the diameter of the root canal and the IAF at WL were assessed. Canals preflared with RaCe instruments had the lowest discrepancy between the apical root canal diameter and the IAF diameter (15.7 ± 9.7 μm) followed by ProTaper (22.2 ± 11.0 μm) and FlexMaster (35.0 ± 17.2 μm). Preflaring of root canals prevents underestimation of the actual apical root canal diameter. The type of instruments used for preflaring show differences on the accuracy of IAF determination. Preflaring with larger tapered instruments leads to a more accurate apical sizing, and this information is crucial concerning the appropriate final diameter for complete apical shaping. Copyright © 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.
Roberts, Michael D; Company, Joseph M; Brown, Jacob D; Toedebusch, Ryan G; Padilla, Jaume; Jenkins, Nathan T; Laughlin, M Harold; Booth, Frank W
2012-08-01
According to the latest data from the Center for Disease Control and Prevention 17%, or 12.5 million, of children and adolescents aged 2-19 years in the United States are obese. Physical inactivity is designated as one of the actual causes of US deaths and undoubtedly contributes to the obesity epidemic in children and adults. Examining the effects of inactivity on physiological homeostasis during youth is crucial given that 58% of children between the ages 6-11 yr old fail to obtain the recommended 60 min/day of physical activity and 92% of adolescents fail to achieve this goal [Troiano et al. Med Sci Sports Exerc. 40, 2008]. Nonetheless, invasive mechanistic studies in children linking diminished physical activity with metabolic maladies are lacking for obvious ethical reasons. The rodent wheel lock (WL) model was adopted by our laboratory and others to study how different organ systems of juvenile rats respond to a cessation of daily physical activity. Our WL model houses rats in cages equipped with voluntary running wheels starting at 28 days of age. After a certain period of voluntary running (3 to 6 wk), the wheels are locked, thus preventing the rats' primary source of physical activity. The studies discussed herein suggest that obesity-associated maladies including skeletal muscle insulin resistance, hypothalamic leptin resistance, fatty acid oxidation impairments in skeletal muscle and adipose tissue, nonalcoholic fatty liver disease, and endothelial dysfunction are initiated in juvenile animals that are restrained from voluntary exercise via WL. The use of the juvenile rodent WL or other inactivity models will continue to provide a powerful clinical translational tool that can be used for primordial prevention of human childhood obesity.
Waste treatment in silicon production operations
NASA Technical Reports Server (NTRS)
Coleman, Larry M. (Inventor); Tambo, William (Inventor)
1985-01-01
A battery of special burners, each adapted for the treatment of a particular range of waste material formed during the conversion of metallurgical grade silicon to high purity silane and silicon, is accompanied by a series arrangement of filters to recover fumed silica by-product and a scrubber to recover muriatic acid as another by-product. All of the wastes are processed, during normal and plant upset waste load conditions, to produce useful by-products in an environmentally acceptable manner rather than waste materials having associated handling and disposal problems.
Assessment of spill flow emissions on the basis of measured precipitation and waste water data
NASA Astrophysics Data System (ADS)
Hochedlinger, Martin; Gruber, Günter; Kainz, Harald
2005-09-01
Combined sewer overflows (CSOs) are substantial contributors to the total emissions into surface water bodies. The emitted pollution results from dry-weather waste water loads, surface runoff pollution and from the remobilisation of sewer deposits and sewer slime during storm events. One possibility to estimate overflow loads is a calculation with load quantification models. Input data for these models are pollution concentrations, e.g. Total Chemical Oxygen Demand (COD tot), Total Suspended Solids (TSS) or Soluble Chemical Oxygen Demand (COD sol), rainfall series and flow measurements for model calibration and validation. It is important for the result of overflow loads to model with reliable input data, otherwise this inevitably leads to bad results. In this paper the correction of precipitation measurements and the sewer online-measurements are presented to satisfy the load quantification model requirements already described. The main focus is on tipping bucket gauge measurements and their corrections. The results evidence the importance of their corrections due the effects on load quantification modelling and show the difference between corrected and not corrected data of storm events with high rain intensities.
A study on the optimal hydraulic loading rate and plant ratios in recirculation aquaponic system.
Endut, Azizah; Jusoh, A; Ali, N; Wan Nik, W B; Hassan, A
2010-03-01
The growths of the African catfish (Clarias gariepinus) and water spinach (Ipomoea aquatica) were evaluated in recirculation aquaponic system (RAS). Fish production performance, plant growth and nutrient removal were measured and their dependence on hydraulic loading rate (HLR) was assessed. Fish production did not differ significantly between hydraulic loading rates. In contrast to the fish production, the water spinach yield was significantly higher in the lower hydraulic loading rate. Fish production, plant growth and percentage nutrient removal were highest at hydraulic loading rate of 1.28 m/day. The ratio of fish to plant production has been calculated to balance nutrient generation from fish with nutrient removal by plants and the optimum ratio was 15-42 gram of fish feed/m(2) of plant growing area. Each unit in RAS was evaluated in terms of oxygen demand. Using specified feeding regime, mass balance equations were applied to quantify the waste discharges from rearing tanks and treatment units. The waste discharged was found to be strongly dependent on hydraulic loading rate. 2009 Elsevier Ltd. All rights reserved.
Sarkar, Omprakash; Venkata Mohan, S
2017-10-01
Application of pre-aeration (AS) to waste prior to feeding was evaluated on acidogenic process in a semi-pilot scale biosystem for the production of biobased products (biohydrogen, volatile fatty acids (VFA) and biohythane) from food waste. Oxygen assisted in pre-hydrolysis of waste along with the suppression of methanogenic activity resulting in enhanced acidogenic product formation. AS operation resulted in 97% improvement in hydrogen conversion efficiency (HCE) and 10% more VFA production than the control. Increasing the organic load (OL) of food waste in association with AS application improved the productivity. The application of AS also influenced concentration and composition of fatty acid. Highest fraction of acetic (5.3g/l), butyric (0.7g/l) and propionic acid (0.84g/l) was achieved at higher OL (100g COD/l) with good degree of acidification (DOA). AS strategy showed positive influence on biofuel (biohydrogen and biohythane) production along with the biosynthesis of short chain fatty acids functioning as a low-cost pretreatment strategy in a single stage bioprocess. Copyright © 2017 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Husnan, M. A.; Ismail, H.; Shuib, R. K.
2018-02-01
Recently, the interest of polymer industry researchers have grown rapidly on the use of specific techniques which can reduce cost and utilize rubber waste into the processing form. The increasing of cognizance in environmental matters and the desire to sustain the resources had fortified the practice of recycling waste materials. In this work, the effect of carbon black loading on curing characteristics and mechanical properties of virgin acrylonitrile butadiene rubber/recycled acrylonitrile butadiene rubber (NBRv/NBRr) blends were studied. Cure time (t90), scorch time (tS2) and swelling percentage decreased but minimum torque (ML) and maximum torque (MH) increased with increasing carbon black (CB) loading in the blends. Increasing CB loading also increased tensile strength, tensile modulus (M100), hardness and compression set but decreased elongation at break (Eb) of NBRv/NBRr blends.
Kavazanjian, Edward; Gutierrez, Angel
2017-10-01
A large scale centrifuge test of a geomembrane-lined landfill subject to waste settlement and seismic loading was conducted to help validate a numerical model for performance based design of geomembrane liner systems. The test was conducted using the 240g-ton centrifuge at the University of California at Davis under the U.S. National Science Foundation Network for Earthquake Engineering Simulation Research (NEESR) program. A 0.05mm thin film membrane was used to model the liner. The waste was modeled using a peat-sand mixture. The side slope membrane was underlain by lubricated low density polyethylene to maximize the difference between the interface shear strength on the top and bottom of the geomembrane and the induced tension in it. Instrumentation included thin film strain gages to monitor geomembrane strains and accelerometers to monitor seismic excitation. The model was subjected to an input design motion intended to simulate strong ground motion from the 1994 Hyogo-ken Nanbu earthquake. Results indicate that downdrag waste settlement and seismic loading together, and possibly each phenomenon individually, can induce potentially damaging tensile strains in geomembrane liners. The data collected from this test is publically available and can be used to validate numerical models for the performance of geomembrane liner systems. Published by Elsevier Ltd.
Experimental Primer on the Trapped Ion Quantum Computer
1998-01-01
analogously), then exposing this ion to a traveling- wave electric field E�r� � E0 cos �k rÿ wLt � j� with frequency wL, phase j, and wavevector k, results...eih�a�a y��ij � Sjÿ eÿih�a�a y�ÿij� �4� in a frame rotating at wL, where terms oscillating faster than W j �Wj wz; w0� have been neglected. Here, h...of the single bit rotation gate and the two-bit controlled-NOT gate [34]. For brevity, we concentrate on these two gates and how they can be
Sannappa, J; Ningappa, C
2014-03-01
An extensive studies on the indoor activity concentrations of thoron, radon and their progeny in the granite region in the state of Karnataka, India, has been carried out since, 2007 in the scope of a lung cancer epidemiological study using solid-state nuclear track detector-based double-chamber dosemeters (LR-115, type II plastic track detector). Seventy-four dwellings of different types were selected for the measurement. The dosemeters containing SSNTD detectors were fixed 2 m above the floor. After an exposure time of 3 months (90 d), films were etched to reveal tracks. From the track density, the concentrations of radon and thoron were evaluated. The value of the indoor concentration of thoron and radon in the study area varies from 16 to 170 Bq m(-3) and 18 to 300 Bq m(-3) with medians of 66 and 82.3 Bq m(-3), respectively, and that of their progeny varies from 1.8 to 24 mWL with a median of 3.6 mWL and 1.6 to 19.6 mWL, respectively. The concentrations of indoor thoron, radon and their progeny and their equivalent effective doses are discussed.
General Dental Practitioners’ Concept towards Using Radiography and Apex-Locators in Endodontics
Raoof, Maryam; Heidaripour, Maryam; Shahravan, Arash; Haghani, Jahangir; Afkham, Arash; Razifar, Mahsa; Mohammadizadeh, Sakineh
2014-01-01
Introduction: Despite being the gold standard as well as a routine technique in endodontics, radiographic working length (WL) determination owns many drawbacks. Electronic apex-locators (EALs) are recommended to complement radiographies. The aim of this study was to evaluate the perceptions of Iranian general dental practitioners (GDPs) towards using radiography and EAL. Methods and Materials: Three hundred and ninety one GDPs attending the 53th Iranian Dental Association Congress completed a questionnaire focusing on the use of radiography and EALs during the various stages of root canal treatment. The data was analyzed with the chi-square test with the level of significance set at 0.05. The results were then calculated as frequencies and percentages. Results: More than half of the GDPs reported using radiographs as the sole method for WL determination. A total of 30.4% of the practitioners were using the combined approach during root canal therapy of a single-rooted tooth, while 38.9% used this method in multi-rooted teeth. Approximately half of the respondents would not order follow-up radiographies after root canal treatment. Conclusion: Radiography continues to be the most common method for WL determination in Iran. PMID:25386209
Surface morphology and structure of Ge layer on Si(111) after solid phase epitaxy
NASA Astrophysics Data System (ADS)
Yoshida, Ryoma; Tosaka, Aki; Shigeta, Yukichi
2018-05-01
The surface morphology change of a Ge layer on a Si(111) surface formed by solid phase epitaxy has been investigated with a scanning tunneling microscope (STM). The Ge film was deposited at room temperature and annealed at 400 °C or 600 °C. The STM images of the sample surface after annealing at 400 °C show a flat wetting layer (WL) with small three-dimensional islands on the WL. After annealing at 600 °C, the STM images show a surface roughening with large islands. From the relation between the average height of the roughness and the deposited layer thickness, it is confirmed that the diffusion of Ge atoms becomes very active at 600 °C. The Si crystal at the interface is reconstructed and the intermixing occurs over 600 °C. However, the intermixing is fairly restricted in the solid phase epitaxy growth at 400 °C. The surface morphology changes with the crystallization at 400 °C are discussed by the shape of the islands formed on the WL surface. It is shown that the diffusion of the Ge atoms in the amorphous phase is active even at 400 °C.
The Magnetic Field of the Class I Protostar WL 17
NASA Astrophysics Data System (ADS)
Johns-Krull, Christopher M.; Greene, T. P.; Doppmann, G.; Covey, K. R.
2007-12-01
Strong stellar magnetic fields are believed to truncate the inner accretion disks around young stars, redirecting the accreting material to the high latitude regions of the stellar surface. In the past few years, observations of strong stellar fields on Classical T Tauri stars [class II young stellar objects (YSOs)] with field strengths in general agreement with the predictions of magnetopsheric accretion theory have bolstered this picture. Currently, nothing is known about the magnetic field properties of younger, more embedded class I YSOs. It is during this protostellar evolutionary phase that stars accrete most of their final mass, but the physics governing this process remains poorly understood. Here, we use high resolution near infrared spectra obtained with NIRSPEC on Keck and with PHOENIX on Gemini South to measure the magnetic field properties of the class I protostar WL 17. We find clear signatures of a strong stellar magnetic field. Initial analysis of this data suggests a surface average field strength of 3.6 kG on the surface of WL 17. This is the highest mean surface field detected to date on any YSO. We present our field measurements and discuss how they fit with the general model of magnetospheric accretion in young stars.
Static critical behavior of the q-states Potts model: High-resolution entropic study
NASA Astrophysics Data System (ADS)
Caparica, A. A.; Leão, Salviano A.; DaSilva, Claudio J.
2015-11-01
Here we report a precise computer simulation study of the static critical properties of the two-dimensional q-states Potts model using very accurate data obtained from a modified Wang-Landau (WL) scheme proposed by Caparica and Cunha-Netto (2012). This algorithm is an extension of the conventional WL sampling, but the authors changed the criterion to update the density of states during the random walk and established a new procedure to windup the simulation run. These few changes have allowed a more precise microcanonical averaging which is essential to a reliable finite-size scaling analysis. In this work we used this new technique to determine the static critical exponents β, γ, and ν, in an unambiguous fashion. The static critical exponents were determined as β = 0.10811(77) , γ = 1.4459(31) , and ν = 0.8197(17) , for the q = 3 case, and β = 0.0877(37) , γ = 1.3161(69) , and ν = 0.7076(10) , for the q = 4 Potts model. A comparison of the present results with conjectured values and with those obtained from other well established approaches strengthens this new way of performing WL simulations.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Choo, S. M.; Lee, K. J.; Park, S. M.
2015-04-27
The magnetotransport properties of Pb(Pd,Co)O{sub 2} and PbPdO{sub 2} thin films were investigated. In magnetoconductance curves, we observed a crossover between weak anti-localization (WAL) and weak localization (WL) depending on the annealing and Co doping in PbPdO{sub 2} thin films. For the Pb(Pd,Co)O{sub 2} case showing WAL signals, the ex-situ annealing weakens the Pd-O hybridization by stabilizing Co{sup 3+} states and generating Pd{sup 1+} states, instead of Pd{sup 2+}, so that the spin-orbit coupling (SOC) strength is significantly reduced. It causes the dominant magnetotransport mechanism change from WAL to WL. This annealing effect is compared with the PbPdO{sub 2} case,more » which possesses WL signals. The annealing process stabilizes the oxygen states and enhances the Pd-O hybridization, and consequently the SOC strength is enhanced. Our experimental results are well explained by the Hikami-Larkin-Nagaoka theory in terms of two important physical parameters; SOC strength-related α and inelastic scattering length l{sub ϕ}.« less
Northwest Africa 10758: A New CV3 Chondrite Bearing a Giant CAI with Hibonite-Rich Wark-Lovering Rim
NASA Technical Reports Server (NTRS)
Ross, D. K.; Simon, J. I.; Zolensky, M.
2017-01-01
Northwest Africa (NWA) 10758 is a newly identified carbonaceous chondrite that is a Bali-like oxidized CV3. The large Ca-Al rich inclusion (CAI) in this sample is approx. 2.4 x 1.4 cm. The CAI is transitional in composition between type A and type B, with interior mineralogy dominated by melilite, plus less abundant spinel and Al-Ti rich diopside, and only very minor anorthite (Fig. 1A). This CAI is largely free of secondary alteration in the exposed section we examined, with almost no nepheline, sodalite or Ca-Fe silicates. The Wark-Lovering (WL) rim on this CAI is dominated by hibonite, with lower abundances of spinel and perovskite, and with hibonite locally overlain by melilite plus perovskite (as in Fig. 1B). Note that the example shown in 1B is exceptional. Around most of the CAI, hibonite + spinel + perovskite form the WL rim, without overlying melilite. The WL rim can be unusually thick, ranging from approx.20 microns up to approx. 150 microns. A well-developed, stratified accretionary rim infills embayments of the CAI, and thins over protuberances in the convoluted CAI surface.
NWA10758: A New CV3 Chondrite Bearing a Giant CAI with Hibonite-Rich Wark-Lovering Rim
NASA Technical Reports Server (NTRS)
Ross, D. K.; Simon, J. I.; Zolensky, M.
2017-01-01
Northwest Africa (NWA) 10758 is a newly identified carbonaceous chondrite that is a Bali-like oxidized CV3. The large Ca-Al rich inclusion (CAI) in this sample is approx. 2.4 x 1.4 cm. The CAI is transitional in composition between type A and type B, with interior mineralogy dominated by melilite, plus less abundant spinel and Al-Ti rich diopside, and only very minor anorthite (Fig. 1A). This CAI is largely free of secondary alteration in the exposed section we examined, with almost no nepheline, sodalite or Ca-Fe silicates. The Wark-Lovering (WL) rim on this CAI is dominated by hibonite, with lower abundances of spinel and perovskite, and with hibonite locally overlain by melilite plus perovskite (as in Fig. 1B). Note that the example shown in 1B is exceptional. Around most of the CAI, hibonite + spinel + perovskite form the WL rim, without overlying melilite. The WL rim can be unusually thick, ranging from approx. 20 microns up to approx. 150 microns. A well-developed, stratified accretionary rim infills embayments of the CAI, and thins over protuberances in the convoluted CAI surface.
Optimal updating magnitude in adaptive flat-distribution sampling
NASA Astrophysics Data System (ADS)
Zhang, Cheng; Drake, Justin A.; Ma, Jianpeng; Pettitt, B. Montgomery
2017-11-01
We present a study on the optimization of the updating magnitude for a class of free energy methods based on flat-distribution sampling, including the Wang-Landau (WL) algorithm and metadynamics. These methods rely on adaptive construction of a bias potential that offsets the potential of mean force by histogram-based updates. The convergence of the bias potential can be improved by decreasing the updating magnitude with an optimal schedule. We show that while the asymptotically optimal schedule for the single-bin updating scheme (commonly used in the WL algorithm) is given by the known inverse-time formula, that for the Gaussian updating scheme (commonly used in metadynamics) is often more complex. We further show that the single-bin updating scheme is optimal for very long simulations, and it can be generalized to a class of bandpass updating schemes that are similarly optimal. These bandpass updating schemes target only a few long-range distribution modes and their optimal schedule is also given by the inverse-time formula. Constructed from orthogonal polynomials, the bandpass updating schemes generalize the WL and Langfeld-Lucini-Rago algorithms as an automatic parameter tuning scheme for umbrella sampling.
Transformation of lymphocytes by Herpesvirus papio.
Falk, L A; Henle, G; Henle, W; Deinhardt, F; Schudel, A
1977-08-15
Cotton-topped (CT) or white-lipped (WL) marmoset lymphocytes were transformed in vitro with herpesvirus papio (HVP) into permanently growing lymphoblastoid cell lines (LCL). Five of 9 HVP-transformed CT cell lines contained cells with antigens reacting with antibodies to Epstein-Barr virus (EBV) capsid antigen (VCA) and/or to EBV-induced early antigens (EA). None of 12 WL LCL revealed such antigen-producing cells. Cells from both groups of cultures failed to react with antibodies to the EBV-specified nuclear antigen (EBNA). Exposure of baboon circulating lymphocytes to X-irradiated HVP or EBV-carring cells, or to suspensions of EBV resulted in establishment of LCL which all contained VCA and/or EA-positive, but no EBNA-positive cells. Nuclear antigens were undetectable also with anti-VCA-positive sera from baboons, chimpanzees, or other non-human primates. DNA-complementary RNA (cRNA) filter hybridization with EBV cRNA showed that with one exception transformed CT or WL marmoset cells contained at least 1-2 virus genome equivalents per cell, while at least 12-25 virus genome equivalents per cell were detected in transformed baboon cells. These data need confirmation by DNA-DNA reassociation kinetics.
Optimal updating magnitude in adaptive flat-distribution sampling.
Zhang, Cheng; Drake, Justin A; Ma, Jianpeng; Pettitt, B Montgomery
2017-11-07
We present a study on the optimization of the updating magnitude for a class of free energy methods based on flat-distribution sampling, including the Wang-Landau (WL) algorithm and metadynamics. These methods rely on adaptive construction of a bias potential that offsets the potential of mean force by histogram-based updates. The convergence of the bias potential can be improved by decreasing the updating magnitude with an optimal schedule. We show that while the asymptotically optimal schedule for the single-bin updating scheme (commonly used in the WL algorithm) is given by the known inverse-time formula, that for the Gaussian updating scheme (commonly used in metadynamics) is often more complex. We further show that the single-bin updating scheme is optimal for very long simulations, and it can be generalized to a class of bandpass updating schemes that are similarly optimal. These bandpass updating schemes target only a few long-range distribution modes and their optimal schedule is also given by the inverse-time formula. Constructed from orthogonal polynomials, the bandpass updating schemes generalize the WL and Langfeld-Lucini-Rago algorithms as an automatic parameter tuning scheme for umbrella sampling.
Makaronidis, Janine M; Neilson, Sabrina; Cheung, Wui-Hang; Tymoszuk, Urszula; Pucci, Andrea; Finer, Nicholas; Doyle, Jacqueline; Hashemi, Majid; Elkalaawy, Mohamed; Adamo, Marco; Jenkinson, Andrew; Batterham, Rachel L
2016-12-01
Reduced energy intake drives weight loss following Roux-en-Y gastric bypass (RYGB) and sleeve gastrectomy (SG) procedures. Post-operative changes in subjective appetite, taste, and smell and food preferences are reported and suggested to contribute to reduced energy intake. We aimed to investigate the prevalence of these changes following RYGB and SG and to evaluate their relationship with weight loss. 98 patients post-RYGB and 155 post-SG from a single bariatric centre were recruited to a cross-sectional study. Participants completed a questionnaire, previously utilised in post-operative bariatric patients, to assess the prevalence of post-operative food aversions and subjective changes in appetite, taste and smell. Anthropometric data were collected and percentage weight loss (%WL) was calculated. The relationship between food aversions, changes in appetite, taste and smell and %WL was assessed. The influence of time post-surgery, gender and type 2 diabetes (T2D) were evaluated. Following RYGB and SG the majority of patients reported food aversions (RYGB = 62%, SG = 59%), appetite changes (RYGB = 91%, SG = 91%) and taste changes (RYGB = 64%, SG = 59%). Smell changes were more common post-RYGB than post-SG (RYGB = 41%, SG = 28%, p = 0.039). No temporal effect was observed post-RYGB. In contrast, the prevalence of appetite changes decreased significantly with time following SG. Post-operative appetite changes associated with and predicted higher %WL post-SG but not post-RYGB. Taste changes associated with and predicted higher %WL following RYGB but not post-SG. There was no gender effect post-RYGB. Post-SG taste changes were less common in males (female = 65%, males = 40%, p = 0.008). T2D status in females did not influence post-operative subjective changes. However, in males with T2D, taste changes were less common post-SG than post-RYGB together with lower %WL (RYGB = 27.5 ± 2.7, SG = 14.6 ± 2.1, p = 0.003). Further research is warranted to define the biology underlying these differences and to individualise treatments. Copyright © 2016 Elsevier Ltd. All rights reserved.
de Bruin, Eduard J; Bögels, Susan M; Oort, Frans J; Meijer, Anne Marie
2015-12-01
To investigate the efficacy of cognitive behavioral therapy for insomnia (CBTI) in adolescents. A randomized controlled trial of CBTI in group therapy (GT), guided internet therapy (IT), and a waiting list (WL), with assessments at baseline, directly after treatment (post-test), and at 2 months follow-up. Diagnostic interviews were held at the laboratory of the Research Institute of Child Development and Education at the University of Amsterdam. Treatment for GT occurred at the mental health care center UvAMinds in Amsterdam, the Netherlands. One hundred sixteen adolescents (mean age = 15.6 y, SD = 1.6 y, 25% males) meeting DSM-IV criteria for insomnia, were randomized to IT, GT, or WL. CBTI of 6 weekly sessions, consisted of psychoeducation, sleep hygiene, restriction of time in bed, stimulus control, cognitive therapy, and relaxation techniques. GT was conducted in groups of 6 to 8 adolescents, guided by 2 trained sleep therapists. IT was applied through an online guided self-help website with programmed instructions and written feedback from a trained sleep therapist. Sleep was measured with actigraphy and sleep logs for 7 consecutive days. Symptoms of insomnia and chronic sleep reduction were measured with questionnaires. Results showed that adolescents in both IT and GT, compared to WL, improved significantly on sleep efficiency, sleep onset latency, wake after sleep onset, and total sleep time at post-test, and improvements were maintained at follow-up. Most of these improvements were found in both objective and subjective measures. Furthermore, insomnia complaints and symptoms of chronic sleep reduction also decreased significantly in both treatment conditions compared to WL. Effect sizes for improvements ranged from medium to large. A greater proportion of participants from the treatment conditions showed high end-state functioning and clinically significant improvement after treatment and at follow-up compared to WL. This study is the first randomized controlled trial that provides evidence that cognitive behavioral therapy for insomnia is effective for the treatment of adolescents with insomnia, with medium to large effect sizes. There were small differences between internet and group therapy, but both treatments reached comparable endpoints. This study was part of the clinical trial: Effectiveness of cognitive behavioral therapy for sleeplessness in adolescents; URL: http://www.isrctn.com/ISRCTN33922163; registration: ISRCTN33922163. © 2015 Associated Professional Sleep Societies, LLC.
Hill, Alison M; Harris Jackson, Kristina A; Roussell, Michael A; West, Sheila G; Kris-Etherton, Penny M
2015-01-01
Background: Food-based dietary patterns emphasizing plant protein that were evaluated in the Dietary Approaches to Stop Hypertension (DASH) and OmniHeart trials are recommended for the treatment of metabolic syndrome (MetS). However, the contribution of plant protein to total protein in these diets is proportionally less than that of animal protein. Objective: This study compared 3 diets varying in type (animal compared with plant) and amount of protein on MetS criteria. Design: Sixty-two overweight adults with MetS consumed a healthy American diet for 2 wk before being randomly allocated to either a modified DASH diet rich in plant protein (18% protein, two-thirds plant sources, n = 9 males, 12 females), a modified DASH diet rich in animal protein (Beef in an Optimal Lean Diet: 18.4% protein, two-thirds animal sources, n = 9 males, 11 females), or a moderate-protein diet (Beef in an Optimal Lean Diet Plus Protein: 27% protein, two-thirds animal sources, n = 10 males, 11 females). Diets were compared across 3 phases of energy balance: 5 wk of controlled (all foods provided) weight maintenance (WM), 6 wk of controlled weight loss (minimum 500-kcal/d deficit) including exercise (WL), and 12 wk of prescribed, free-living weight loss (FL). The primary endpoint was change in MetS criteria. Results: All groups achieved ∼5% weight loss at the end of the WL phase and maintained it through FL, with no between-diet differences (WM compared with WL, FL, P < 0.0001; between diets, P = NS). All MetS criteria decreased independent of diet composition (main effect of phase, P < 0.01; between diets, P = NS). After WM, all groups had a MetS prevalence of 80–90% [healthy American diet (HAD) compared with WM, P = NS], which decreased to 50–60% after WL and was maintained through FL (HAD, WM vs WL, FL, P < 0.01). Conclusions: Weight loss was the primary modifier of MetS resolution in our study population regardless of protein source or amount. Our findings demonstrate that heart-healthy weight-loss dietary patterns that emphasize either animal or plant protein improve MetS criteria similarly. This study was registered at clinicaltrials.gov as NCT00937638. PMID:26354540
NASA Astrophysics Data System (ADS)
Carlson, C. W.; Faulds, J. E.
2014-12-01
Positioned between the Sierra Nevada microplate and Basin and Range in western North America, the Walker Lane (WL) accommodates ~20% of the dextral motion between the North American and Pacific plates on predominately NW-striking dextral and ENE to E-W-striking sinistral fault systems. The Terrill Mountains (TM) lie at the northern terminus of a domain of dextral faults accommodating translation of crustal-blocks in the central WL and at the southeast edge of sinistral faults accommodating oroclinal flexure and CW rotation of blocks in the northern WL. As the mechanisms of strain transfer between these disparate fault systems are poorly understood, the thick Oligocene to Pliocene volcanic strata of the TM area make it an ideal site for studying the transfer of strain between regions undergoing differing styles of deformation and yet both accommodating dextral shear. Detailed geologic mapping and paleomagnetic study of ash-flow tuffs in the TM region has been conducted to elucidate Neogene strain accommodation for this transitional region of the WL. Strain at the northernmost TM appears to be transferred from a system of NW-striking dextral faults to a system of ~E-W striking sinistral faults with associated CW flexure. A distinct ~23 Ma paleosol is locally preserved below the tuff of Toiyabe and provides an important marker bed. This paleosol is offset with ~6 km of dextral separation across the fault bounding the NE flank of the TM. This fault is inferred as the northernmost strand of the NW-striking, dextral Benton Spring fault system, with offset consistent with minimums constrained to the south (6.4-9.6 km, Gabbs Valley Range). Paleomagnetic results suggest counter-intuitive CCW vertical-axis rotation of crustal blocks south of the domain boundary in the system of NW-striking dextral faults, similar to some other domains of NW-striking dextral faults in the northern WL. This may result from coeval dextral shear and WNW-directed extension within the left-stepping system of dextral fault. The left steps are analogous to Riedel shears developing above a more through-going shear zone at depth. However, a site directly adjacent to the Benton Springs fault is rotated ~30° CW, likely due to fault drag. These results show the complex and important contribution of vertical-axis rotations in accommodation of dextral shear.
NASA Astrophysics Data System (ADS)
Tang, F. K.; Cui, M.; Lu, Q.; Liu, Y. G.; Guo, H. Y.; Zhou, J. X.
2015-08-01
Changes in soil utilization significantly affect aggregate stability and aggregate-associated soil organic carbon (SOC). A field investigation and indoor analysis were conducted in order to study the soil aggregate stability and organic carbon distribution in the water-stable aggregates (WSA) of the bare land (BL), grassland (GL), shrubland (SL), and woodland (WL) in a typical karst gorge region. The results indicated that the BL, GL, SL, and WL were dominated by particles with sizes > 5 mm under dry sieving treatment, and that the soil aggregate contents of various sizes decreased as the particle size decreased. In addition, the BL, GL, SL, and WL were predominantly comprised of WSA < 0.25 mm under wet sieving treatment, and that the WSA contents initially increased, then decreased, and then increased again as the particle size decreased. Furthermore, at a soil depth of 0-60 cm, the mean weight diameter (MWD), geometrical mean diameter (GMD), and fractal dimensions (D) of the dry aggregates and water-stable aggregates in the different types of land were ranked, in descending order, as WL > GL > SL > BL. The contents of WSA > 0.25 mm, MWD and GMD increased significantly, in that order, and the percentage of aggregate destruction (PAD) and fractal dimensions decreased significantly as the soil aggregate stability improved. The results of this study indicated that, as the SOC contents increased after vegetation restoration, the average SOC content of WL was 2.35, 1.37, and 1.26 times greater than that in the BL, GL, and SL, respectively. The total SOC and SOC associated in WSA of various sizes were the highest at a soil depth of 0-20 cm. In addition, the SOC contents of the WSA increased as the soil aggregate sizes decreased. The SOC contents of the WSA < 0.25 mm were highest except in the bare land, and the SOC contents of the aggregates < 0.25 mm, which ranged from 18.85 to 41.08 %, comprised the majority of the total aggregate SOC contents. The woodland and grassland facilitated WSA stability and SOC protection, thus, promoting the natural restoration of vegetation by reducing artificial disturbances could effectively restore the ecology of and prevent soil erosion in karst regions.
Nishimura, Hiroto; Tan, Li; Sun, Zhao-Yong; Tang, Yue-Qin; Kida, Kenji; Morimura, Shigeru
2016-02-01
Waste paper can serve as a feedstock for ethanol production due to being rich in cellulose and not requiring energy-intensive thermophysical pretreatment. In this study, an efficient process was developed to convert waste paper to ethanol. To accelerate enzymatic saccharification, pH of waste paper slurry was adjusted to 4.5-5.0 with H2SO4. Presaccharification and simultaneous saccharification and fermentation (PSSF) with enzyme loading of 40 FPU/g waste paper achieved an ethanol yield of 91.8% and productivity of 0.53g/(Lh) with an ethanol concentration of 32g/L. Fed-batch PSSF was used to decrease enzyme loading to 13 FPU/g waste paper by feeding two separate batches of waste paper slurry. Feeding with 20% w/w waste paper slurry increased ethanol concentration to 41.8g/L while ethanol yield decreased to 83.8%. To improve the ethanol yield, presaccharification was done prior to feeding and resulted in a higher ethanol concentration of 45.3g/L, a yield of 90.8%, and productivity of 0.54g/(Lh). Ethanol fermentation recovered 33.2% of the energy in waste paper as ethanol. The biochemical methane potential of the stillage eluted from ethanol fermentation was 270.5mL/g VTS and 73.0% of the energy in the stillage was recovered as methane. Integrating ethanol fermentation with methane fermentation, recovered a total of 80.4% of the energy in waste paper as ethanol and methane. Copyright © 2015 Elsevier Ltd. All rights reserved.
Integrated waste and water management system
NASA Technical Reports Server (NTRS)
Murray, R. W.; Sauer, R. L.
1986-01-01
The performance requirements of the NASA Space Station have prompted a reexamination of a previously developed integrated waste and water management system that used distillation and catalytic oxydation to purify waste water, and microbial digestion and incineration for waste solids disposal. This system successfully operated continuously for 206 days, for a 4-man equivalent load of urine, feces, wash water, condensate, and trash. Attention is given to synergisms that could be established with other life support systems, in the cases of thermal integration, design commonality, and novel technologies.
Cesium Sorption/Desorption Experiments with IONSIV(R) IE-911 in Radioactive Waste
DOE Office of Scientific and Technical Information (OSTI.GOV)
Walker, D.D.
2001-02-13
This report describes cesium desorption from IONSIV IE-911 during ambient temperature storage and following temperature increases to 35 and 55 degrees C. This report also describes cesium sorption following return to ambient temperature. The IONSIV IE-911 used in these tests was loaded with cesium from Tank 44F radioactive waste in an ion exchange column test in 1999. Cesium desorbed and resorbed in the presence of Tank 44F waste and simulated waste solutions.
Road Map for Development of Crystal-Tolerant High Level Waste Glasses
DOE Office of Scientific and Technical Information (OSTI.GOV)
Matyas, Josef; Vienna, John D.; Peeler, David
This road map guides the research and development for formulation and processing of crystal-tolerant glasses, identifying near- and long-term activities that need to be completed over the period from 2014 to 2019. The primary objective is to maximize waste loading for Hanford waste glasses without jeopardizing melter operation by crystal accumulation in the melter or melter discharge riser. The potential applicability to the Savannah River Site (SRS) Defense Waste Processing Facility (DWPF) is also addressed in this road map.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Andrews, M.K.
1999-05-10
Using ORNL information on the characterization of the tank waste sludges, SRTC performed extensive bench-scale vitrification studies using simulants. Several glass systems were tested to ensure the optimum glass composition (based on the glass liquidus temperature, viscosity and durability) is determined. This optimum composition will balance waste loading, melt temperature, waste form performance and disposal requirements. By optimizing the glass composition, a cost savings can be realized during vitrification of the waste. The preferred glass formulation was selected from the bench-scale studies and recommended to ORNL for further testing with samples of actual OR waste tank sludges.
DOE Office of Scientific and Technical Information (OSTI.GOV)
S.M. Frank
Work describe in this report represents the final year activities for the 3-year International Nuclear Energy Research Initiative (I-NERI) project: Development and Characterization of New High-Level Waste Forms for Achieving Waste Minimization from Pyroprocessing. Used electrorefiner salt that contained actinide chlorides and was highly loaded with surrogate fission products was processed into three candidate waste forms. The first waste form, a high-loaded ceramic waste form is a variant to the CWF produced during the treatment of Experimental Breeder Reactor-II used fuel at the Idaho National Laboratory (INL). The two other waste forms were developed by researchers at the Korean Atomicmore » Energy Research Institute (KAERI). These materials are based on a silica-alumina-phosphate matrix and a zinc/titanium oxide matrix. The proposed waste forms, and the processes to fabricate them, were designed to immobilize spent electrorefiner chloride salts containing alkali, alkaline earth, lanthanide, and halide fission products that accumulate in the salt during the processing of used nuclear fuel. This aspect of the I-NERI project was to demonstrate 'hot cell' fabrication and characterization of the proposed waste forms. The outline of the report includes the processing of the spent electrorefiner salt and the fabrication of each of the three waste forms. Also described is the characterization of the waste forms, and chemical durability testing of the material. While waste form fabrication and sample preparation for characterization must be accomplished in a radiological hot cell facility due to hazardous radioactivity levels, smaller quantities of each waste form were removed from the hot cell to perform various analyses. Characterization included density measurement, elemental analysis, x-ray diffraction, scanning electron microscopy and the Product Consistency Test, which is a leaching method to measure chemical durability. Favorable results from this demonstration project will provide additional options for fission product immobilization and waste management associated the electrochemical/pyrometallurgical processing of used nuclear fuel.« less
Beisner, Kimberly R.; Marston, Thomas M.; Naftz, David L.; Snyder, Terry; Freeman, Michael L.
2010-01-01
During May, June, and July 2007, 58 solid-phase samples were collected from abandoned uranium mine waste dumps, background sites, and adjacent streambeds in Red, White, and Fry Canyons in southeastern Utah. The objectives of this sampling program were to (1) assess the nonpoint-source chemical loading potential to ephemeral and perennial drainage basins from uranium waste dumps and (2) assess potential effects on human health due to recreational activities on and around uranium waste dumps on Bureau of Land Management property. Uranium waste-dump samples were collected using solid-phase sampling protocols. After collection, solid-phase samples were homogenized and extracted in the laboratory using a leaching procedure. Filtered (0.45 micron) water samples were obtained from the field leaching procedure and were analyzed for major and trace elements at the Inductively Coupled Plasma-Mass Spectrometry Metals Analysis Laboratory at the University of Utah. A subset of the solid-phase samples also were digested with strong acids and analyzed for major ions and trace elements at the U.S. Geological Survey Geologic Division Laboratory in Denver, Colorado. For the initial ranking of chemical loading potential for uranium waste dumps, results of leachate analyses were compared with existing aquatic-life and drinking-water-quality standards. To assess potential effects on human health, solid-phase digestion values for uranium were compared to soil screening levels (SSL) computed using the computer model RESRAD 6.5 for a probable concentration of radium. One or more chemical constituents exceeded aquatic life and drinking-water-quality standards in approximately 64 percent (29/45) of the leachate samples extracted from uranium waste dumps. Most of the uranium waste dump sites with elevated trace-element concentrations in leachates were located in Red Canyon. Approximately 69 percent (31/45) of the strong acid digestible soil concentration values were greater than a calculated SSL. Uranium waste dump sites with elevated leachate and total digestible concentrations may need to be further investigated to determine the most appropriate remediation method.
Approach to the vadose zone monitoring in hazardous and solid waste disposal facilities
NASA Astrophysics Data System (ADS)
Twardowska, Irena
2004-03-01
In the solid waste (SW)disposal sites, in particular at the unlined facilities, at the remediated or newly-constructed units equipped with novel protective/reactive permeable barriers or at lined facilities with leachate collection systems that are prone to failure, the vadose zone monitoring should comprise besides the natural soil layer beneath the landfill, also the anthropogenic vadose zone, i.e. the waste layer and pore solutions in the landfill. The vadose zone screening along the vertical profile of SW facilities with use of direct invasive soil-core and soil-pore liquid techniques shows vertical downward redistribution of inorganic (macroconstituents and heavy metals) and organic (PAHs) contaminant loads in water infiltrating through the waste layer. These loads can make ground water down-gradient of the dump unfit for any use. To avoid damage of protective/reactive permeable barriers and liners, an installation of stationary monitoring systems along the waste layer profile during the construction of a landfill, which are amenable to generate accurate data and information in a near-real time should be considered including:(i) permanent samplers of pore solution, with a periodic pump-induced transport of collected solution to the surface, preferably with instant field measurements;(ii)chemical sensors with continuous registration of critical parameters. These techniques would definitely provide an early alert in case when the chemical composition of pore solution percolating downward the waste profile shows unfavorable transformations, which indicate an excessive contaminant load approaching ground water. The problems concerning invasive and stationary monitoring of the vadose zone in SW disposal facilities will be discussed at the background of results of monitoring data and properties of permeable protective/reactive barriers considered for use.
Tavakoli, Ali; Nikoo, Mohammad Reza; Kerachian, Reza; Soltani, Maryam
2015-04-01
In this paper, a new fuzzy methodology is developed to optimize water and waste load allocation (WWLA) in rivers under uncertainty. An interactive two-stage stochastic fuzzy programming (ITSFP) method is utilized to handle parameter uncertainties, which are expressed as fuzzy boundary intervals. An iterative linear programming (ILP) is also used for solving the nonlinear optimization model. To accurately consider the impacts of the water and waste load allocation strategies on the river water quality, a calibrated QUAL2Kw model is linked with the WWLA optimization model. The soil, water, atmosphere, and plant (SWAP) simulation model is utilized to determine the quantity and quality of each agricultural return flow. To control pollution loads of agricultural networks, it is assumed that a part of each agricultural return flow can be diverted to an evaporation pond and also another part of it can be stored in a detention pond. In detention ponds, contaminated water is exposed to solar radiation for disinfecting pathogens. Results of applying the proposed methodology to the Dez River system in the southwestern region of Iran illustrate its effectiveness and applicability for water and waste load allocation in rivers. In the planning phase, this methodology can be used for estimating the capacities of return flow diversion system and evaporation and detention ponds.
Combustion of a Pb(II)-loaded olive tree pruning used as biosorbent.
Ronda, A; Della Zassa, M; Martín-Lara, M A; Calero, M; Canu, P
2016-05-05
The olive tree pruning is a specific agroindustrial waste that can be successfully used as adsorbent, to remove Pb(II) from contaminated wastewater. Its final incineration has been studied in a thermobalance and in a laboratory flow reactor. The study aims at evaluating the fate of Pb during combustion, at two different scales of investigation. The flow reactor can treat samples approximately 10(2) larger than the conventional TGA. A detailed characterization of the raw and Pb(II)-loaded waste, before and after combustion is presented, including analysis of gas and solids products. The Pb(II)-loaded olive tree pruning has been prepared by a previous biosorption step in a lead solution, reaching a concentration of lead of 2.3 wt%. Several characterizations of the ashes and the mass balances proved that after the combustion, all the lead presents in the waste remained in ashes. Combustion in a flow reactor produced results consistent with those obtained in the thermobalance. It is thus confirmed that the combustion of Pb(II)-loaded olive tree pruning is a viable option to use it after the biosorption process. The Pb contained in the solid remained in the ashes, preventing possible environmental hazards. Copyright © 2016 Elsevier B.V. All rights reserved.
Wilber, William G.; Crawford, Charles G.; Peters, James G.
1979-01-01
The Indiana State Board of Health is developing a State water-quality management plan that includes establishing limits for wastewater effluents discharged into Indiana streams. A digital model calibrated to conditions in Silver Creek was used to develop alternatives for future waste loadings that would be compatible with Indiana stream water-quality standards defined for two critical hydrologic conditions, summer and winter low flows. Effluents from the Sellersburg and Clarksville-North wastewater-treatment facilities are the only point-source waste loads that significantly affect the water quality in the modeled segment of Silver Creek. Model simulations indicate that nitrification is the most significant factor affecting the dissolved-oxygen concentration in Silver Creek during summer and winter low flows. Natural streamflow in Silver Creek during the summer and annual 7-day, 10-year low flow is zero, so no benefit from dilution is provided. Present ammonia-nitrogen and dissolved-oxygen concentrations of effluent from the Sellersburg and Clarksville-North wastewater-treatment facilities will violate current Indiana water-quality standards for ammonia toxicity and dissolved oxygen during summer and winter low flows. The current biochemical-oxygen demand limits for the Sellersburg and Clarksville-North wastewater-treatment facilities are not sufficient to maintain an average dissolved-oxygen concentration of at least 5 milligrams per liter, the State 's water-quality standard for streams. Calculations of the stream 's assimilative capacity indicate that Silver Creek cannot assimilate additional waste loadings and meet current Indiana water-quality standards. (Kosco-USGS)
Microbial Community in a Biofilter for Removal of Low Load Nitrobenzene Waste Gas
Zhai, Jian; Wang, Zhu; Shi, Peng; Long, Chao
2017-01-01
To improve biofilter performance, the microbial community of a biofilter must be clearly defined. In this study, the performance of a lab-scale polyurethane biofilter for treating waste gas with low loads of nitrobenzene (NB) (< 20 g m-3 h-1) was investigated when using different empty bed residence times (EBRT) (64, 55.4 and 34 s, respectively). In addition, the variations of the bacterial community in the biofilm on the longitudinal distribution of the biofilters were analysed by using Illumina MiSeq high-throughput sequencing. The results showed that NB waste gas was successfully degraded in the biofilter. High-throughput sequencing data suggested that the phylum Actinobacteria and genus Rhodococcus played important roles in the degradation of NB. The variations of the microbial community were attributed to the different intermediate degradation products of NB in each layer. The strains identified in this study were potential candidates for purifying waste gas effluents containing NB. PMID:28114416
Evaluating the Rheological Properties of Waste Natural Rubber Latex Modified Binder
NASA Astrophysics Data System (ADS)
Khatijah Abu Bakar, Siti; Ezree Abdulah, Mohd; Mustafa Kamal, Mazlina; Rahman, Raha Abd; Arifin Hadithon, Kamarul; Buhari, Rosnawati; Tajudin, Saiful Azhar Ahmad
2018-03-01
Road surface is designed to be the durable surface material to sustain the traffic loading. However, due to physical and mechanical stress, pavement deterioration is accelerated. Thus, modifying conventional bitumen by improving its properties is seen as the best method to prolong pavement in-service life. The purpose of this paper is to study the effect of waste natural rubber (NR) latex on rheological properties of bitumen. Conventional bitumen PEN 80/100 was modified with different content of waste NR latex using a high shear mixer at temperature of 150°C. The modified binder properties were characterized by conducting physical test (i.e. softening point, penetration and penetration index) and rheological test (i.e. dynamic shear rheometer, DSR). Results showed that, the addition of waste NR latex improved the rheology properties, which indicates by improving of rutting factor (G*/sin δ). This properties improvement has also shows a potential to resist deformation on road surface despite of high traffic loading.