Areas on which to focus when seeking to reduce the greenhouse gas emissions of commercial waste management. A case study of a hypermarket, Finland.

PubMed

Hupponen, M; Grönman, K; Horttanainen, M

2018-03-22

This study focuses on commercial waste, which has received less attention than household waste in regards to greenhouse gas emission research. First, the global warming potential (GWP) of commercial waste management was calculated. Second, the impacts of different waste fractions and the processes of waste management were recognised. Third, the key areas on which to focus when aiming to reduce the greenhouse gas emissions of commercial waste management were determined. This study was conducted on the waste generated by a real hypermarket in South-East Finland and included eight different waste fractions. The waste treatment plants were selected based on the actual situation. Three different scenarios were employed to evaluate the environmental impact of managing mixed waste: landfilling, combustion and more accurate source separation. The GaBi software and impact assessment methodology CML 2001 were used to perform a life cycle assessment of the environmental impacts associated with the waste management. The results indicated that the total GWP of commercial waste management could be reduced by 93% by directing the mixed waste to combustion instead of landfill. A further 5% GWP reduction could be achieved by more accurate source separation of the mixed waste. Utilisation of energy waste had the most significant influence (41-52%) on the total GWP (-880 to -860 kgCO 2 -eq./t), followed by landfilling of mixed waste (influence 15-23% on the total GWP, 430 kgCO 2 -eq./t), recycling polyethylene (PE) plastic (influence 18-21% on the total GWP, -1800 kgCO 2 -eq./t) and recycling cardboard (influence 11-13% on the total GWP, 51 kgCO 2 -eq./t). A key focus should be placed on treatment processes and substitutions, especially in terms of substitutions of energy waste and PE plastic. This study also clarified the importance of sorting PE plastic, even though the share of this waste fraction was not substantial. The results of this paper were compared to those of previous studies. The output of this analysis indicated that the total GWP can be significantly reduced by identifying an alternative recycling or incineration location for cardboard where it is used to substitute virgin material or replace fossil fuels respectively. In conclusion, it is essential to note that waste management companies have a notable influence on the emissions of commercial waste management because they choose the places at which the waste fractions are treated and utilised. Copyright © 2018 Elsevier Ltd. All rights reserved.

Health care waste management practice in a hospital.

PubMed

Paudel, R; Pradhan, B

2010-10-01

Health-care waste is a by-product of health care. Its poor management exposes health-care workers, waste handlers and the community to infections, toxic effects and injuries including damage of the environment. It also creates opportunities for the collection of disposable medical equipment, its re-sale and potential re-use without sterilization, which causes an important burden of disease worldwide. The purpose of this study was to find out health care waste management practice in hospital. A cross-sectional study was conducted in Narayani Sub-Regional Hospital, Birgunj from May to October 2006 using both qualitative and quantitative methods. Study population was four different departments of the hospital (Medical/Paediatric, Surgical/Ortho, Gynae/Obstetric and Emergency), Medical Superintendent, In-charges of four different departments and all sweepers. Data was collected using interview, group discussion, observation and measurement by weight and volume. Total health-care waste generated was 128.4 kg per day while 0.8 kg per patient per day. The composition of health care waste was found to be 96.8 kg (75.4%) general waste, 24.1 kg (8.8%) hazardous waste and 7.5 kg (5.8%) sharps per day by weight. Health staffs and sweepers were not practicing the waste segregation. Occupational health and safety was not given due attention. Majority of the sweepers were unaware of waste management and need of safety measures to protect their own health. Health care waste management practice in the hospital was unsatisfactory because of the lack of waste management plan and carelessness of patients, visitors and staffs. Therefore the hospital should develop the waste management plan and strictly follow the National Health Care Waste Management Guideline.

Medical Waste Management in Community Health Centers.

PubMed

Tabrizi, Jafar Sadegh; Rezapour, Ramin; Saadati, Mohammad; Seifi, Samira; Amini, Behnam; Varmazyar, Farahnaz

2018-02-01

Non-standard management of medical waste leads to irreparable side effects. This issue is of double importance in health care centers in a city which are the most extensive system for providing Primary Health Care (PHC) across Iran cities. This study investigated the medical waste management standards observation in Tabriz community health care centers, northwestern Iran. In this triangulated cross-sectional study (qualitative-quantitative), data collecting tool was a valid checklist of waste management process developed based on Iranian medical waste management standards. The data were collected in 2015 through process observation and interviews with the health center's staff. The average rate of waste management standards observance in Tabriz community health centers, Tabriz, Iran was 29.8%. This case was 22.8% in dimension of management and training, 27.3% in separating and collecting, 31.2% in transport and temporary storage, and 42.9% in sterilization and disposal. Lack of principal separation of wastes, inappropriate collecting and disposal cycle of waste and disregarding safety tips (fertilizer device performance monitoring, microbial cultures and so on) were among the observed defects in health care centers supported by quantitative data. Medical waste management was not in a desirable situation in Tabriz community health centers. The expansion of community health centers in different regions and non-observance of standards could predispose to incidence the risks resulted from medical wastes. So it is necessary to adopt appropriate policies to promote waste management situation.

Development of demand forecasting tool for natural resources recouping from municipal solid waste.

PubMed

Zaman, Atiq Uz; Lehmann, Steffen

2013-10-01

Sustainable waste management requires an integrated planning and design strategy for reliable forecasting of waste generation, collection, recycling, treatment and disposal for the successful development of future residential precincts. The success of the future development and management of waste relies to a high extent on the accuracy of the prediction and on a comprehensive understanding of the overall waste management systems. This study defies the traditional concepts of waste, in which waste was considered as the last phase of production and services, by putting forward the new concept of waste as an intermediate phase of production and services. The study aims to develop a demand forecasting tool called 'zero waste index' (ZWI) for measuring the natural resources recouped from municipal solid waste. The ZWI (ZWI demand forecasting tool) quantifies the amount of virgin materials recovered from solid waste and subsequently reduces extraction of natural resources. In addition, the tool estimates the potential amount of energy, water and emissions avoided or saved by the improved waste management system. The ZWI is tested in a case study of waste management systems in two developed cities: Adelaide (Australia) and Stockholm (Sweden). The ZWI of waste management systems in Adelaide and Stockholm is 0.33 and 0.17 respectively. The study also enumerates per capita energy savings of 2.9 GJ and 2.83 GJ, greenhouse gas emissions reductions of 0.39 tonnes (CO2e) and 0.33 tonnes (CO2e), as well as water savings of 2.8 kL and 0.92 kL in Adelaide and Stockholm respectively.

A total quality management approach to healthcare waste management in Namazi Hospital, Iran.

PubMed

Askarian, Mehrdad; Heidarpoor, Peigham; Assadian, Ojan

2010-11-01

Healthcare waste comprises all wastes generated at healthcare facilities, medical research centers and laboratories. Although 75-90% of these wastes are classified as household waste posing no potential risk, 10-25% are deemed to be hazardous, representing a potential threat to healthcare workers, patients, the environment and even the general population, if not disposed of appropriately. If hazardous and non-hazardous waste is mixed and not segregated prior to disposal, costs will increase substantially. Medical waste management is a worldwide issue. In Iran, the majority of problems are associated with an exponential growth in the healthcare sector together with low- or non-compliance with guidelines and recommendations. The aim of this study was to reduce the amounts of infectious waste by clear definition and segregation of waste at the production site in Namazi Hospital in Shiraz, Iran. Namazi Hospital was selected as a study site with an aim to achieving a significant decrease in infectious waste and implementing a total quality management (TQM) method. Infectious and non-infectious waste was weighed at 29 admission wards over a 1-month period. Before the introduction of the new guidelines and the new waste management concept, weight of total waste was 6.67 kg per occupied bed per day (kg/occupied bed/day), of which 73% was infectious and 27% non-infectious waste. After intervention, total waste was reduced to 5.92 kg/occupied bed/day, of which infectious waste represented 61% and non-infectious waste 30%. The implementation of a new waste management concept achieved a 26% reduction in infectious waste. A structured waste management concept together with clear definitions and staff training will result in waste reduction, consequently leading to decreased expenditure in healthcare settings. Copyright © 2010 Elsevier Ltd. All rights reserved.

Disaster waste management: a review article.

PubMed

Brown, Charlotte; Milke, Mark; Seville, Erica

2011-06-01

Depending on their nature and severity, disasters can create large volumes of debris and waste. The waste can overwhelm existing solid waste management facilities and impact on other emergency response and recovery activities. If poorly managed, the waste can have significant environmental and public health impacts and can affect the overall recovery process. This paper presents a system overview of disaster waste management based on existing literature. The main literature available to date comprises disaster waste management plans or guidelines and isolated case studies. There is ample discussion on technical management options such as temporary storage sites, recycling, disposal, etc.; however, there is little or no guidance on how these various management options are selected post-disaster. The literature does not specifically address the impact or appropriateness of existing legislation, organisational structures and funding mechanisms on disaster waste management programmes, nor does it satisfactorily cover the social impact of disaster waste management programmes. It is envisaged that the discussion presented in this paper, and the literature gaps identified, will form a basis for future comprehensive and cohesive research on disaster waste management. In turn, research will lead to better preparedness and response to disaster waste management problems. Copyright © 2011 Elsevier Ltd. All rights reserved.

Disaster waste management: A review article

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Charlotte, E-mail: charlotte.brown@pg.canterbury.ac.nz; Milke, Mark, E-mail: mark.milke@canterbury.ac.nz; Seville, Erica, E-mail: erica.seville@canterbury.ac.nz

2011-06-15

Depending on their nature and severity, disasters can create large volumes of debris and waste. The waste can overwhelm existing solid waste management facilities and impact on other emergency response and recovery activities. If poorly managed, the waste can have significant environmental and public health impacts and can affect the overall recovery process. This paper presents a system overview of disaster waste management based on existing literature. The main literature available to date comprises disaster waste management plans or guidelines and isolated case studies. There is ample discussion on technical management options such as temporary storage sites, recycling, disposal, etc.;more » however, there is little or no guidance on how these various management options are selected post-disaster. The literature does not specifically address the impact or appropriateness of existing legislation, organisational structures and funding mechanisms on disaster waste management programmes, nor does it satisfactorily cover the social impact of disaster waste management programmes. It is envisaged that the discussion presented in this paper, and the literature gaps identified, will form a basis for future comprehensive and cohesive research on disaster waste management. In turn, research will lead to better preparedness and response to disaster waste management problems.« less

Hazardous healthcare waste management in the Kingdom of Bahrain.

PubMed

Mohamed, L F; Ebrahim, S A; Al-Thukair, A A

2009-08-01

Hazardous healthcare waste has become an environmental concern for many developing countries including the Kingdom of Bahrain. There have been several significant obstacles facing the Kingdom in dealing with this issue including; limited documentation regarding generation, handling, management, and disposal of waste. This in turn hinders efforts to plan better healthcare waste management. In this paper, hazardous waste management status in the Kingdom has been investigated through an extensive survey carried out on selected public and private healthcare premises. Hazardous waste management practices including: waste generation, segregation, storage, collection, transportation, treatment, and disposal were determined. The results of this study along with key findings are discussed and summarized. In addition; several effective recommendations and improvements of hazardous waste management are suggested.

Solid industrial wastes and their management in Asegra (Granada, Spain)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casares, M.L.; Ulierte, N.; Mataran, A.

ASEGRA is an industrial area in Granada (Spain) with important waste management problems. In order to properly manage and control waste production in industry, one must know the quantity, type, and composition of industrial wastes, as well as the management practices of the companies involved. In our study, questionnaires were used to collect data regarding methods of waste management used in 170 of the 230 businesses in the area of study. The majority of these companies in ASEGRA are small or medium-size, and belong to the service sector, transport, and distribution. This was naturally a conditioning factor in both themore » type and management of the wastes generated. It was observed that paper and cardboard, plastic, wood, and metals were the most common types of waste, mainly generated from packaging (49% of the total volume), as well as material used in containers and for wrapping products. Serious problems were observed in the management of these wastes. In most cases they were disposed of by dumping, and very rarely did businesses resort to reuse, recycling or valorization. Smaller companies encountered greater difficulties when it came to effective waste management. The most frequent solution for the disposal of wastes in the area was dumping.« less

Trend of the research on construction and demolition waste management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yuan Hongping, E-mail: hpyuan2005@gmail.com; Shen Liyin, E-mail: bsshen@polyu.edu.hk

2011-04-15

Research interests in addressing construction and demolition (C and D) waste management issues have resulted in a large amount of publications during the last decade. This study demonstrates that there is no systematic examination on the research development in literature in the discipline of C and D waste management. This study presents the latest research trend in the discipline through analyzing the publications from 2000 to 2009 in eight major international journals. The analysis is conducted on the number of papers published annually, main authors' contributions, research methods and data analysis methods adopted, and research topics covered. The results exhibitmore » an increasing research interest in C and D waste management in recent years. Researchers from developed economies have contributed significantly to the development of the research in the discipline. Some developing countries such as Malaysia and China have also been making good efforts in promoting C and D waste management research. The findings from this study also indicate that survey and case study are major methods for data collection, and the data are mostly processed through descriptive analysis. It is anticipated that more future studies on C and D waste management will be led by researchers from developing economies, where construction works will remain their major economic activities. On the other hand, more sophisticated modeling and simulating techniques have been used effectively in a number of studies on C and D waste management research, and this is considered a major methodology for future research in the discipline. C and D waste management will continue to be a hot research topic in the future, in particularly, the importance of human factors in C and D waste management has emerged as a new challenging topic.« less

Trend of the research on construction and demolition waste management.

PubMed

Yuan, Hongping; Shen, Liyin

2011-04-01

Research interests in addressing construction and demolition (C&D) waste management issues have resulted in a large amount of publications during the last decade. This study demonstrates that there is no systematic examination on the research development in literature in the discipline of C&D waste management. This study presents the latest research trend in the discipline through analyzing the publications from 2000 to 2009 in eight major international journals. The analysis is conducted on the number of papers published annually, main authors' contributions, research methods and data analysis methods adopted, and research topics covered. The results exhibit an increasing research interest in C&D waste management in recent years. Researchers from developed economies have contributed significantly to the development of the research in the discipline. Some developing countries such as Malaysia and China have also been making good efforts in promoting C&D waste management research. The findings from this study also indicate that survey and case study are major methods for data collection, and the data are mostly processed through descriptive analysis. It is anticipated that more future studies on C&D waste management will be led by researchers from developing economies, where construction works will remain their major economic activities. On the other hand, more sophisticated modeling and simulating techniques have been used effectively in a number of studies on C&D waste management research, and this is considered a major methodology for future research in the discipline. C&D waste management will continue to be a hot research topic in the future, in particularly, the importance of human factors in C&D waste management has emerged as a new challenging topic. Copyright © 2010 Elsevier Ltd. All rights reserved.

Critical management practices influencing on-site waste minimization in construction projects.

PubMed

Ajayi, Saheed O; Oyedele, Lukumon O; Bilal, Muhammad; Akinade, Olugbenga O; Alaka, Hafiz A; Owolabi, Hakeem A

2017-01-01

As a result of increasing recognition of effective site management as the strategic approach for achieving the required performance in construction projects, this study seeks to identify the key site management practices that are requisite for construction waste minimization. A mixed methods approach, involving field study and survey research were used as means of data collection. After confirmation of construct validity and reliability of scale, data analysis was carried out through a combination of Kruskal-Wallis test, descriptive statistics and exploratory factor analysis. The study suggests that site management functions could significantly reduce waste generation through strict adherence to project drawings, and by ensuring fewer or no design changes during construction process. Provision of waste skips for specific materials and maximisation of on-site reuse of materials are also found to be among the key factors for engendering waste minimization. The result of factor analysis suggests four factors underlying on-site waste management practices with 96.093% of total variance. These measures include contractual provisions for waste minimization, waste segregation, maximisation of materials reuse and effective logistic management. Strategies through which each of the underlying measures could be achieved are further discussed in the paper. Findings of this study would assist construction site managers and other site operatives in reducing waste generated by construction activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing the management of healthcare waste in Hawassa city, Ethiopia.

PubMed

Israel Deneke Haylamicheal; Mohamed Aqiel Dalvie; Biruck Desalegn Yirsaw; Hanibale Atsbeha Zegeye

2011-08-01

Inadequate management of healthcare waste is a serious concern in many developing countries due to the risks posed to human health and the environment. This study aimed to evaluate healthcare waste management in Hawassa city, Ethiopia. The study was conducted in nine healthcare facilities (HCFs) including hospitals (four), health centres (two) and higher clinics (three) in two phases, first to assess the waste management aspect and second to determine daily waste generation rate. The result showed that the median quantity of waste generated at the facilities was 3.46 kg bed(-1) day(-1) (range: 1.48-8.19 kg bed(-1) day(-1)). The quantity of waste per day generated at a HCF increased as occupancy increased (p < 0.001). The percentage hazardous waste generated at government HCFs was more than at private HCFs (p < 0.05). The proportion of hazardous waste (20-63.1%) generated at the different HCFs was much higher than the WHO recommendation (10-25%). There was no waste segregation in most HCFs and only one used a complete color coding system. Solid waste and wastewater were stored, transported, treated and disposed inappropriately at all HCFs. Needle-stick injuries were prevalent in 25-100% of waste handlers employed at these HCFs. Additionally, low levels of training and awareness of waste legislation was prevalent amongst staff. The study showed that management of healthcare waste at HCFs to be poor. Waste management practices need to be improved through improved legislation and enforcement, and training of staff in the healthcare facilities in Hawassa.

Between hype and veracity; privatization of municipal solid waste management and its impacts on the informal waste sector.

PubMed

Sandhu, Kiran; Burton, Paul; Dedekorkut-Howes, Aysin

2017-01-01

The informal waste recycling sector has been an indispensable but ironically invisible part of the waste management systems in developing countries as India, often completely disregarded and overlooked by decision makers and policy frameworks. The turn towards liberalization of economy since 1991 in India opened the doors for privatization of urban services and the waste sector found favor with private companies facilitated by the local governments. In joining the privatization bandwagon, the local governments aim to create an image of a progressive city demonstrated most visibly through apt management of municipal solid waste. Resultantly, the long important stakeholder, the informal sector has been sidelined and left to face the adverse impacts of privatization. There is hardly any recognition of its contributions or any attempt to integrate it within the formal waste management systems. The study investigates the impacts of privatization on the waste pickers in waste recycling operations. Highlighting the other dimension of waste collection and management in urban India the study focuses on the waste pickers and small time informal scrap dealers and this is done by taking the case study of Amritsar city, which is an important historic centre and a metropolitan city in the state of Punjab, India. The paper develops an analytical framework, drawing from literature review to analyze the impacts. In conclusion, it supports the case for involving informal waste sector towards achieving sustainable waste management in the city. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparison of municipal solid waste management systems in Canada and Ghana: A case study of the cities of London, Ontario, and Kumasi, Ghana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Asase, Mizpah; Yanful, Ernest K.; Mensah, Moses

2009-10-15

Integrated waste management has been accepted as a sustainable approach to solid waste management in any region. It can be applied in both developed and developing countries. The difference is the approach taken to develop the integrated waste management system. This review looks at the integrated waste management system operating in the city of London, Ontario-Canada and how lessons can be drawn from the system's development and operation that will help implement a sustainable waste management system in the city of Kumasi, Ghana. The waste management system in London is designed such that all waste generated in the city ismore » handled and disposed of appropriately. The responsibility of each sector handling waste is clearly defined and monitored. All major services are provided and delivered by a combination of public and private sector forces. The sustainability of the waste management in the city of London is attributed to the continuous improvement strategy framework adopted by the city based on the principles of integrated waste management. It is perceived that adopting a strategic framework based on the principles of integrated waste management with a strong political and social will, can transform the current waste management in Kumasi and other cities in developing countries in the bid for finding lasting solutions to the problems that have plagued the waste management system in these cities.« less

Study of waste management towards sustainable green campus in Universitas Gadjah Mada

NASA Astrophysics Data System (ADS)

Setyowati, Mega; Kusumawanto, Arif; Prasetya, Agus

2018-05-01

Waste management is a part of the green campus achievement program. Universitas Gadjah Mada has a Standard Operating Procedure for managing produced waste. Waste produced by each building or work unit is temporarily accommodated in the waste depot before dumped into the landfill. This research aims to study the waste management system in UGM, in accordance with the concept of a green campus. The concept of green campus to improve the efficiency of waste management needs to be supported by various parties. The success of the green campus program relies on an integrated approach, a sustainable implementation that involves stakeholders of the university. In actualizing the concept of a green campus, the university has its own waste processing system. The organic produced waste is processed into compost, while plastic waste is converted into alternative fuel. Overall, the waste management system that UGM owns is ineffective and inefficient, it was proved by the fact that there is still much waste dumped into the landfill. UGM provides a laboratory that is specialized to process waste that is produced by UGM. It is planned to be able to reduce the amount of waste that is dumped into the landfill. According to the results, vermicomposting technology, the manufacture of liquid fertilizer from leachate, and the manufacture of the composite from a mixture of leaves and paper were offered as solutions.

Design and implementation of integrated solid wastes management pattern in industrial zones, case study of Shahroud, Iran.

PubMed

Saeid, Nazemi; Roudbari, Aliakbar; Yaghmaeian, Kamyar

2014-01-14

The aim of the study was to design and implementation of integrated solid wastes management pattern in Shahroud industrial zone, evaluates the results and determine possible performance problems. This cross - sectional study was carried out for 4 years in Shahroud industrial zone and the implementation process included:1- Qualitative and quantitative analysis of all solid waste generated in the city, 2- determine the current state of solid waste management in the zone and to identify programs conducted, 3- Design and implementation of integrated solid wastes management pattern including design and implementation of training programs, laws, penalties and incentives and explain and implement programs for all factories and 4- The monitoring of the implementation process and determine the results. Annually, 1,728 tons of solid wastes generated in the town including 1603 tons of industrial wastes and 125 tons of municipal wastes. By implementing this pattern, the two separated systems of collection and recycling of domestic and industrial wastes was launched in this zone. Also consistent with the goals, the amount of solid wastes generated and disposed in 2009 was 51.5 and 28.6 kg per 100 million Rials production, respectively. Results showed that implementation of pattern of separated collection, training programs, capacity building, providing technical services, completing chain of industries and strengthening the cooperation between industrial estate management and industrial units could greatly reduce the waste management problems.

From waste to sustainable materials management: Three case studies of the transition journey.

PubMed

Silva, Angie; Rosano, Michele; Stocker, Laura; Gorissen, Leen

2017-03-01

Waste policy is increasingly moving on from the 'prevention of waste' to a 'sustainable materials policy' focused agenda recognising individual wastes as a resource. In order to comparatively analyse policy developments in enhanced waste management, three case studies were selected; San Francisco's Zero Waste Program, Flanders's Sustainable Materials Management Initiative and Japan's Sound Material-Cycle Society Plan. These case studies were chosen as an opportunity to investigate the variety of leading approaches, governance structures, and enhanced waste policy outcomes, emerging globally. This paper concludes that the current transitional state of waste management across the world, is only in the first leg of the journey towards Circular Economy closed loop production models of waste as a resource material. It is suggested that further development in government policy, planning and behaviour change is required. A focus on material policy and incorporating multiple front runners across industry and knowledge institutions are offered as potential directions in the movement away from end-pipe land-fill solutions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Baseline for food waste generation - A case study in Universiti Tun Hussein Onn Malaysia cafeterias

NASA Astrophysics Data System (ADS)

Alias, A. R.; Mokhlis, N. A. Mohd; Zainun, N. Y.

2017-11-01

Increasing population and economy status have contributed to the increasing volume of solid wastes produced in Malaysia and it creates problems on the existing solid waste management system. Ineffective waste management system was one of the issues that often discussed. The purpose of this study was to suggest the best method for managing food waste in Universiti Tun Hussein Onn Malaysia (UTHM) cafeterias. The scope of the study was to identify the type and quantity of waste generated in each cafeteria. The study area was carried out at six cafeteria in UTHM including residential college cafeteria which are Tun Dr. Ismail (TDI), Tun Fatimah (TF) and Tun Syed Nasir (TSN), G3’s cafeteria, Arked, and Dr. Munie’s cafeteria located at the Faculty of Civil and Environmental Engineering (FKAAS). In this study, food waste was quantified in unit of kilogram (kg). Results of the study showed that total food waste in selected UTHM’s cafeterias was 6197.5 kg for two months. Food waste generated in G3’s cafeteria was the highest value with 1823.5 kg among another cafeteria. This is due to strategic location for students and staff to take meals, the variety of food sold and reasonable price were major factors of generating food waste. Meanwhile, the Dr. Munie's Cafeteria located in FKAAS recorded the least total production of food waste as staffs and students take their meals at others cafeterias. Through literature review, there are list of methods on waste management were identified and composting method was suggested for food waste management in UTHM since the waste was produce in very large quantity.

Identifying potential environmental impacts of waste handling strategies in textile industry.

PubMed

Yacout, Dalia M M; Hassouna, M S

2016-08-01

Waste management is a successful instrument to minimize generated waste and improve environmental conditions. In spite of the large share of developing countries in the textile industry, limited information is available concerning the waste management strategies implemented for textiles on those countries and their environmental impacts. In the current study, two waste management approaches for hazardous solid waste treatment of acrylic fibers (landfill and incineration) were investigated. The main research questions were: What are the different impacts of each waste management strategy? Which waste management strategy is more ecofriendly? Life cycle assessment was employed in order to model the environmental impacts of each waste streaming approach separately then compare them together. Results revealed that incineration was the more ecofriendly approach. Highest impacts of both approaches were on ecotoxicity and carcinogenic potentials due to release of metals from pigment wastes. Landfill had an impact of 46.8 % on human health as compared to 28 % by incineration. Incineration impact on ecosystem quality was higher than landfill impact (68.4 and 51.3 %, respectively). As for resources category, incineration had a higher impact than landfill (3.5 and 2.0 %, respectively). Those impacts could be mitigated if state-of-the-art landfill or incinerator were used and could be reduced by applying waste to energy approaches for both management systems In conclusion, shifting waste treatment from landfill to incineration would decrease the overall environmental impacts and allow energy recovery. The potential of waste to energy approach by incineration with heat recovery could be considered in further studies. Future research is needed in order to assess the implementation of waste management systems and the preferable waste management strategies in the textile industry on developing countries.

Fine granular of shredded waste tyre for road kerb application as improvised road furniture

NASA Astrophysics Data System (ADS)

Munikanan, Vikneswaran; Yahya, Muhamad Azani; Yusof, Mohammed Alias; Radzi, Muhammad Haris Fauzan

2018-02-01

Solid waste management in Malaysia was still in a backward stage. Population growth, urbanization and rapid industrialization led to an increase in the solid waste generated by society. Solid waste management is one of the main problems faced by the community, especially in the city. Solid waste management costs of the collection, collecting, transporting waste to the landfill, is very high. The quantity of solid waste should be reduced in order to reduce government spending. Moreover, improper solid waste management caused a negative impact on people and the environment. Method of recycling is one of the best alternatives to reduce the number of solid waste. Therefore, this study was to identify methods of recycling used tires to be used in civil engineering. This study was conducted to determine the effectiveness and properties of rubber from used tires to be add in the road kerb design.

Solid-waste management in Jalandhar city and its impact on community health

PubMed Central

Puri, Avinash; Kumar, Manoj; Johal, Eonkar

2008-01-01

In this study, solid-waste management practices were evaluated in order to find out its link with occurrence of vector-borne disease. Strategies for solid-waste management were employed as practical model to solve the problems regarding pollution which is originated by solid-waste. PMID:20040983

Health Care Waste Management Practice in Health Care Institutions of Nepal.

PubMed

Joshi, H D; Acharya, T; Ayer, R; Dhakal, P; Karki, K B; Dhimal, M

2017-01-01

Medical waste is considered as a major public health hazard. In a developing country like Nepal, there is much concern about the management practice of medical waste. This study aimed to assess Health Care Waste Management practice among Health Care Institutions in Nepal. A cross sectional study was carried out between July 2012 to June 2013 in 62 different Health Care Institutions, selected from stratified proportionate random sampling technique from all administrative regions of Nepal. A structured questionnaire and observation checklist were used for data collection. The waste generation rate is found significantly correlated with bed capacity, patient flow rate and annual budget spent in the hospital. It is found significantly higher in Teaching hospital than other Health Care Institutions of Nepal. An average of 3.3 kg/day/patient of medical waste (2.0 kg/day/patient non-hazardous and 1.0 kg/day/patient hazardous waste) was generated during the study period. Further, it was found that most of the Health care wastes were not disinfected before transportation to waste disposal sites. Very limited number of Health Care Institutions had conducted Environmental Assessment. Similarly, some of the Health Care Institutions had not followed Health care waste management guideline 2009 of Nepal Government. We found poor compliance of medical waste management practice as per existing legislation of Government of Nepal. Hence, additional effort is needed for improvement of Health care waste management practice at Health Care Institutions of Nepal.

Greenhouse gas emissions of waste management processes and options: A case study.

PubMed

de la Barrera, Belen; Hooda, Peter S

2016-07-01

Increasing concern about climate change is prompting organisations to mitigate their greenhouse gas emissions. Waste management activities also contribute to greenhouse gas emissions. In the waste management sector, there has been an increasing diversion of waste sent to landfill, with much emphasis on recycling and reuse to prevent emissions. This study evaluates the carbon footprint of the different processes involved in waste management systems, considering the entire waste management stream. Waste management data from the Royal Borough of Kingston upon Thames, London (UK), was used to estimate the carbon footprint for its (Royal Borough of Kingston upon Thames) current source segregation system. Second, modelled full and partial co-mingling scenarios were used to estimate carbon emissions from these proposed waste management approaches. The greenhouse gas emissions from the entire waste management system at Royal Borough of Kingston upon Thames were 12,347 t CO2e for the source-segregated scenario, and 11,907 t CO2e for the partial co-mingled model. These emissions amount to 203.26 kg CO2e t(-1) and 196.02 kg CO2e t(-1) municipal solid waste for source-segregated and partial co-mingled, respectively. The change from a source segregation fleet to a partial co-mingling fleet reduced the emissions, at least partly owing to a change in the number and type of vehicles. © The Author(s) 2016.

Assessment of environmental policy implementation in solid waste management in Kathmandu, Nepal.

PubMed

Dangi, Mohan B; Schoenberger, Erica; Boland, John J

2017-06-01

In Nepal, full-fledged environmental legislation was rare before the democratic constitution of 1990. The first law covering the environment and sustainability was the Environment Protection Act 1997. While the Solid Waste Act was introduced in 1987, the problem of solid waste management still surfaces in Kathmandu. In order to understand the bedrock of this unrelenting failure in solid waste management, the manuscript digs deeper into policy implementation by dissecting solid waste rules, environmental legislations, relevant local laws, and solid waste management practices in Kathmandu, Nepal. A very rich field study that included surveys, interviews, site visits, and literature review provided the basis for the article. The study shows that volumes of new Nepalese rules are crafted without effective enforcement of their predecessors and there is a frequent power struggle between local government bodies and central authority in implementing the codes and allocating resources in solid waste management. The study concludes that Kathmandu does not require any new instrument to address solid waste problems; instead, it needs creation of local resources, execution of local codes, and commitment from central government to allow free exercise of these policies.

Developing a master plan for hospital solid waste management: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karamouz, Mohammad; Zahraie, Banafsheh; Kerachian, Reza

2007-07-01

Disposal of about 1750 tons of solid wastes per day is the result of a rapid population growth in the province of Khuzestan in the south west of Iran. Most of these wastes, especially hospital solid wastes which have contributed to the pollution of the environment in the study area, are not properly managed considering environmental standards and regulations. In this paper, the framework of a master plan for managing hospital solid wastes is proposed considering different criteria which are usually used for evaluating the pollution of hospital solid waste loads. The effectiveness of the management schemes is also evaluated.more » In order to rank the hospitals and determine the share of each hospital in the total hospital solid waste pollution load, a multiple criteria decision making technique, namely analytical hierarchy process (AHP), is used. A set of projects are proposed for solid waste pollution control and reduction in the proposed framework. It is partially applied for hospital solid waste management in the province of Khuzestan, Iran. The results have shown that the hospitals located near the capital city of the province, Ahvaz, produce more than 43% of the total hospital solid waste pollution load of the province. The results have also shown the importance of improving management techniques rather than building new facilities. The proposed methodology is used to formulate a master plan for hospital solid waste management.« less

Geographic information system-based healthcare waste management planning for treatment site location and optimal transportation routeing.

PubMed

Shanmugasundaram, Jothiganesh; Soulalay, Vongdeuane; Chettiyappan, Visvanathan

2012-06-01

In Lao People's Democratic Republic (Lao PDR), a growth of healthcare centres, and the environmental hazards and public health risks typically accompanying them, increased the need for healthcare waste (HCW) management planning. An effective planning of an HCW management system including components such as the treatment plant siting and an optimized routeing system for collection and transportation of waste is deemed important. National government offices at developing countries often lack the proper tools and methodologies because of the high costs usually associated with them. However, this study attempts to demonstrate the use of an inexpensive GIS modelling tool for healthcare waste management in the country. Two areas were designed for this study on HCW management, including: (a) locating centralized treatment plants and designing optimum travel routes for waste collection from nearby healthcare facilities; and (b) utilizing existing hospital incinerators and designing optimum routes for collecting waste from nearby healthcare facilities. Spatial analysis paved the way to understand the spatial distribution of healthcare wastes and to identify hotspots of higher waste generating locations. Optimal route models were designed for collecting and transporting HCW to treatment plants, which also highlights constraints in collecting and transporting waste for treatment and disposal. The proposed model can be used as a decision support tool for the efficient management of hospital wastes by government healthcare waste management authorities and hospitals.

Reverse logistics network for municipal solid waste management: The inclusion of waste pickers as a Brazilian legal requirement.

PubMed

Ferri, Giovane Lopes; Chaves, Gisele de Lorena Diniz; Ribeiro, Glaydston Mattos

2015-06-01

This study proposes a reverse logistics network involved in the management of municipal solid waste (MSW) to solve the challenge of economically managing these wastes considering the recent legal requirements of the Brazilian Waste Management Policy. The feasibility of the allocation of MSW material recovery facilities (MRF) as intermediate points between the generators of these wastes and the options for reuse and disposal was evaluated, as well as the participation of associations and cooperatives of waste pickers. This network was mathematically modelled and validated through a scenario analysis of the municipality of São Mateus, which makes the location model more complete and applicable in practice. The mathematical model allows the determination of the number of facilities required for the reverse logistics network, their location, capacities, and product flows between these facilities. The fixed costs of installation and operation of the proposed MRF were balanced with the reduction of transport costs, allowing the inclusion of waste pickers to the reverse logistics network. The main contribution of this study lies in the proposition of a reverse logistics network for MSW simultaneously involving legal, environmental, economic and social criteria, which is a very complex goal. This study can guide practices in other countries that have realities similar to those in Brazil of accelerated urbanisation without adequate planning for solid waste management, added to the strong presence of waste pickers that, through the characteristic of social vulnerability, must be included in the system. In addition to the theoretical contribution to the reverse logistics network problem, this study aids in decision-making for public managers who have limited technical and administrative capacities for the management of solid wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

A mathematical model for municipal solid waste management - A case study in Hong Kong.

PubMed

Lee, C K M; Yeung, C L; Xiong, Z R; Chung, S H

2016-12-01

With the booming economy and increasing population, the accumulation of waste has become an increasingly arduous issue and has aroused the attention from all sectors of society. Hong Kong which has a relative high daily per capita domestic waste generation rate in Asia has not yet established a comprehensive waste management system. This paper conducts a review of waste management approaches and models. Researchers highlight that mathematical models provide useful information for decision-makers to select appropriate choices and save cost. It is suggested to consider municipal solid waste management in a holistic view and improve the utilization of waste management infrastructures. A mathematical model which adopts integer linear programming and mixed integer programming has been developed for Hong Kong municipal solid waste management. A sensitivity analysis was carried out to simulate different scenarios which provide decision-makers important information for establishing Hong Kong waste management system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Towards Sustainable Ambon Bay: Evaluation of Solid Waste Management in Ambon City

NASA Astrophysics Data System (ADS)

Maryati, S.; Miharja, M.; Iscahyono, A. F.; Arsallia, S.; Humaira, AN S.

2017-07-01

Ambon Bay is a strategic area in the context of regional economic development, however it also faced environmental problems due to economic development and the growth of population. One of the environmental problems in the Ambon Bay is the growing solid waste which in turn lowers the quality of the water. The purpose of this study is to evaluate solid waste management in the Ambon City and propose recommendation in order to reduce solid waste in the Ambon Bay. The analytical method used is descriptive analysis by comparing a number of criteria based on the concept of solid waste management in coastal region with the current conditions of solid waste management in Ambon City. Criteria for waste management are divided into generation, storage, collection, transport, transfer and disposal. From the results of analysis, it can be concluded that the components of solid waste management at transport, transfer, and disposal level are generally still adequate, but solid waste management at source, storage and collection level have to be improved.

Solid waste management in Thailand: an overview and case study (Tha Khon Yang sub-district).

PubMed

Yukalang, Nachalida; Clarke, Beverley Dawn; Ross, Kirstin Elizabeth

2017-09-26

Due to rapid urbanization, solid waste management (SWM) has become a significant issue in several developing countries including Thailand. Policies implemented by the Central Thai Government to manage SWM issues have had only limited success. This article reviews current municipal waste management plans in Thailand and examines municipal waste management at the local level, with focus on the Tha Khon Yang sub-district surrounding Mahasarakham University in Mahasarakham Province. Within two decades this area has been converted from a rural to an urban landscape featuring accommodation for over 45,000 university students and a range of business facilities. This development and influx of people has outpaced the government's ability to manage municipal solid waste (MSW). There are significant opportunities to improve local infrastructure and operational capacity; but there are few mechanisms to provide and distribute information to improve community participation in waste management. Many community-based waste management projects, such as waste recycling banks, the 3Rs (reduce, reuse and recycle), and waste-to-biogas projects have been abandoned. Additionally, waste from Tha Kon Yang and its surrounding areas has been transferred to unsanitary landfills; there is also haphazard dumping and uncontrolled burning of waste, which exacerbate current pollution issues.

Investigating factors influencing construction waste management efforts in developing countries: an experience from Thailand.

PubMed

Manowong, Ektewan

2012-01-01

Rapid economic growth and urbanization in developing countries lead to extensive construction activities that generate a large amount of waste. A challenge is how to manage construction waste in the most sustainable way. In the developing world, research on construction waste management is scarce and such academic knowledge needs to be responsive to actual practices in the industry in order to be implemented. As construction projects involve a number of participants and stakeholders, their participation and commitment can have a major influence on the goals of green and sustainable construction for urban development. This study provides a significant step in conducting a very first research of this kind in Thailand by aiming to investigate the level of construction stakeholders' commitment as well as the achievement of construction waste management in order to improve short-term practices and to establish a long-term strategic construction waste management plan. In this study, a structural equation model was employed to investigate the influence of factors that are related to environmental aspects, social aspects, and economic aspect of construction waste management. Concern about health and safety was found to be the most significant and dominant influence on the achievement of sustainable construction waste management. Other factors affecting the successful management of construction waste in Thai construction projects were also identified. It is perceived that this study has potential to contribute useful guidelines for practitioners both in Thailand and other developing countries with similar contexts.

Preliminary study on enhancing waste management best practice model in Malaysia construction industry

NASA Astrophysics Data System (ADS)

Jamaludin, Amril Hadri; Karim, Nurulzatushima Abdul; Noor, Raja Nor Husna Raja Mohd; Othman, Nurulhidayah; Malik, Sulaiman Abdul

2017-08-01

Construction waste management (CWM) is the practice of minimizing and diverting construction waste, demolition debris, and land-clearing debris from disposal and redirecting recyclable resources back into the construction process. Best practice model means best choice from the collection of other practices that was built for purpose of construction waste management. The practice model can help the contractors in minimizing waste before the construction activities will be started. The importance of minimizing wastage will have direct impact on time, cost and quality of a construction project. This paper is focusing on the preliminary study to determine the factors of waste generation in the construction sites and identify the effectiveness of existing construction waste management practice conducted in Malaysia. The paper will also include the preliminary works of planned research location, data collection method, and analysis to be done by using the Analytical Hierarchy Process (AHP) to help in developing suitable waste management best practice model that can be used in the country.

Towards the effective plastic waste management in Bangladesh: a review.

PubMed

Mourshed, Monjur; Masud, Mahadi Hasan; Rashid, Fazlur; Joardder, Mohammad Uzzal Hossain

2017-12-01

The plastic-derived product, nowadays, becomes an indispensable commodity for different purposes. A huge amount of used plastic causes environmental hazards that turn in danger for marine life, reduces the fertility of soil, and contamination of ground water. Management of this enormous plastic waste is challenging in particular for developing countries like Bangladesh. Lack of facilities, infrastructure development, and insufficient budget for waste management are some of the prime causes of improper plastic management in Bangladesh. In this study, the route of plastic waste production and current plastic waste management system in Bangladesh have been reviewed extensively. It emerges that no technical and improved methods are adapted in the plastic management system. A set of the sustainable plastic management system has been proposed along with the challenges that would emerge during the implementation these strategies. Successful execution of the proposed systems would enhance the quality of plastic waste management in Bangladesh and offers enormous energy from waste.

Comparative Analysis of Households Solid Waste Management in Rural and Urban Ghana

PubMed Central

Appiah, Divine Odame; Poku, Adjoa Afriyie; Garsonu, Emmanuel Kofi

2016-01-01

The comparative analysis of solid waste management between rural and urban Ghana is largely lacking. This study investigated the solid waste situation and the organisation of solid waste management in both urban and rural settings from the perspective of households. The study employed cross-sectional survey covering both rural and urban districts in the Ashanti and Greater Accra Regions of Ghana. The study systematically sampled houses from which 400 households and respondents were randomly selected. Pearson's Chi square test was used to compare demographic and socioeconomic variables in rural and urban areas. Multivariate Test, Tests of Between-Subjects Effects, and Pair-Wise Comparisons were performed through one-way MANOVA to determine whether or not solid waste situations in rural and urban areas are significantly different. The results revealed that location significantly affects solid waste management in Ghana. Urban communities had lower mean scores than rural communities for poor solid waste situation in homes. However, urban communities had higher mean scores than rural communities for poor solid waste situation in principal streets and dumping sites. The study recommends that the local government authorities implement very comprehensive policies (sanitary inspection, infrastructure development, and community participation) that will take into consideration the specific solid waste management needs of both urban and rural areas. PMID:27807453

Comparative Analysis of Households Solid Waste Management in Rural and Urban Ghana.

PubMed

Boateng, Simon; Amoako, Prince; Appiah, Divine Odame; Poku, Adjoa Afriyie; Garsonu, Emmanuel Kofi

2016-01-01

The comparative analysis of solid waste management between rural and urban Ghana is largely lacking. This study investigated the solid waste situation and the organisation of solid waste management in both urban and rural settings from the perspective of households. The study employed cross-sectional survey covering both rural and urban districts in the Ashanti and Greater Accra Regions of Ghana. The study systematically sampled houses from which 400 households and respondents were randomly selected. Pearson's Chi square test was used to compare demographic and socioeconomic variables in rural and urban areas. Multivariate Test, Tests of Between-Subjects Effects, and Pair-Wise Comparisons were performed through one-way MANOVA to determine whether or not solid waste situations in rural and urban areas are significantly different. The results revealed that location significantly affects solid waste management in Ghana. Urban communities had lower mean scores than rural communities for poor solid waste situation in homes. However, urban communities had higher mean scores than rural communities for poor solid waste situation in principal streets and dumping sites. The study recommends that the local government authorities implement very comprehensive policies (sanitary inspection, infrastructure development, and community participation) that will take into consideration the specific solid waste management needs of both urban and rural areas.

Application of life cycle assessment for hospital solid waste management: A case study.

PubMed

Ali, Mustafa; Wang, Wenping; Chaudhry, Nawaz

2016-10-01

This study was meant to determine environmental aspects of hospital waste management scenarios using a life cycle analysis approach. The survey for this study was conducted at the largest hospital in a major city of Pakistan. The hospital was thoroughly analyzed from November 2014 to January 2015 to quantify its wastes by category. The functional unit of the study was selected as 1 tonne of disposable solid hospital waste. System boundaries included transportation of hospital solid waste and its treatment and disposal by landfilling, incineration, composting, and material recycling methods. These methods were evaluated based on their greenhouse gas emissions. Landfilling and incineration turned out to be the worst final disposal alternatives, whereas composting and material recovery displayed savings in emissions. An integrated system (composting, incineration, and material recycling) was found as the best solution among the evaluated scenarios. This study can be used by policymakers for the formulation of an integrated hospital waste management plan. This study deals with environmental aspects of hospital waste management scenarios. It is an increasing area of concern in many developing and resource-constrained countries of the world. The life cycle analysis (LCA) approach is a useful tool for estimation of greenhouse gas emissions from different waste management activities. There is a shortage of information in existing literature regarding LCA of hospital wastes. To the best knowledge of the authors this work is the first attempt at quantifying the environmental footprint of hospital waste in Pakistan.

A model to minimize joint total costs for industrial waste producers and waste management companies.

PubMed

Tietze-Stöckinger, Ingela; Fichtner, Wolf; Rentz, Otto

2004-12-01

The model LINKopt is a mixed-integer, linear programming model for mid- and long-term planning of waste management options on an inter-company level. There has been a large increase in the transportation of waste material in Germany, which has been attributed to the implementation of the European Directive 75/442/EEC on waste. Similar situations are expected to emerge in other European countries. The model LINKopt has been developed to determine a waste management system with minimal decision-relevant costs considering transportation, handling, storage and treatment of waste materials. The model can serve as a tool to evaluate various waste management strategies and to obtain the optimal combination of investment options. In addition to costs, ecological aspects are considered by determining the total mileage associated with the waste management system. The model has been applied to a German case study evaluating different investment options for a co-operation between Daimler-Chrysler AG at Rastatt, its suppliers, and the waste management company SITA P+R GmbH. The results show that the installation of waste management facilities at the premises of the waste producer would lead to significant reductions in costs and transportation.

Hospital waste management in developing countries: A mini review.

PubMed

Ali, Mustafa; Wang, Wenping; Chaudhry, Nawaz; Geng, Yong

2017-06-01

Health care activities can generate different kinds of hazardous wastes. Mismanagement of these wastes can result in environmental and occupational health risks. Developing countries are resource-constrained when it comes to safe management of hospital wastes. This study summarizes the main issues faced in hospital waste management in developing countries. A review of the existing literature suggests that regulations and legislations focusing on hospital waste management are recent accomplishments in many of these countries. Implementation of these rules varies from one hospital to another. Moreover, wide variations exist in waste generation rates within as well as across these countries. This is mainly attributable to a lack of an agreement on the definitions and the methodology among the researchers to measure such wastes. Furthermore, hospitals in these countries suffer from poor waste segregation, collection, storage, transportation and disposal practices, which can lead to occupational and environmental risks. Knowledge and awareness regarding proper waste management remain low in the absence of training for hospital staff. Moreover, hospital sanitary workers, and scavengers, operate without the provision of safety equipment or immunization. Unsegregated waste is illegally recycled, leading to further safety risks. Overall, hospital waste management in developing countries faces several challenges. Sustainable waste management practices can go a long way in reducing the harmful effects of hospital wastes.

Current practices of construction waste reduction through 3R practice among contractors in malaysia: Case study in penang

NASA Astrophysics Data System (ADS)

Ng, L. S.; Tan, L. W.; Seow, T. W.

2017-11-01

The effectiveness of the implementation of construction waste reduction through 3R reflects the sustainability in construction waste management. Weak implementation of construction waste reduction through 3R among contractors will lead to unsustainable construction waste management. Increase in construction waste on landfills is critical especially on islands where land is very limited for solid waste disposal. This aim of this paper is to investigate current practice of construction waste reduction through 3R practice among contractors in Penang, Malaysia. The findings reported herein is based on feedbacks from 143 construction contractors of grade CIDB G7, G6 and G5 in Penang and experts from Penang Local Authority, CIDB in Penang and its Headquarters, National Solid Waste Management Department, and Headquarters of Solid Waste and Public Cleansing Management Corporation. Interviews and questionnaire surveys have been found that 3R practice is not mandatory in construction waste management in Penang. Only 39.8% construction contractors practiced 3R in managing their waste. Therefore, 3R practices should be emphasized in construction industry. Reducing wastes through 3R practices in construction industry is a way forward towards sustainable construction waste management especially in expanding the lifetime of landfill.

Design and implementation of integrated solid wastes management pattern in industrial zones, case study of Shahroud, Iran

PubMed Central

2014-01-01

Background The aim of the study was to design and implementation of integrated solid wastes management pattern in Shahroud industrial zone, evaluates the results and determine possible performance problems. This cross - sectional study was carried out for 4 years in Shahroud industrial zone and the implementation process included:1- Qualitative and quantitative analysis of all solid waste generated in the city, 2- determine the current state of solid waste management in the zone and to identify programs conducted, 3- Design and implementation of integrated solid wastes management pattern including design and implementation of training programs, laws, penalties and incentives and explain and implement programs for all factories and 4- The monitoring of the implementation process and determine the results. Results Annually, 1,728 tons of solid wastes generated in the town including 1603 tons of industrial wastes and 125 tons of municipal wastes. By implementing this pattern, the two separated systems of collection and recycling of domestic and industrial wastes was launched in this zone. Also consistent with the goals, the amount of solid wastes generated and disposed in 2009 was 51.5 and 28.6 kg per 100 million Rials production, respectively. Conclusion Results showed that implementation of pattern of separated collection, training programs, capacity building, providing technical services, completing chain of industries and strengthening the cooperation between industrial estate management and industrial units could greatly reduce the waste management problems. PMID:24423020

Environmental impacts and benefits of state-of-the-art technologies for E-waste management.

PubMed

Ikhlayel, Mahdi

2017-10-01

This study aims to evaluate the environmental impacts and benefits of state-of-the-art technologies for proper e-waste handling using Jordan as a case study. Life Cycle Assessment (LCA) was employed to evaluate five advanced management systems represent state-of-the-art treatment technologies, including sanitary landfilling; proper recycling of metals, materials, and precious metals (PMs); and incineration of plastic and the hazardous portion of printed circuit boards (PCBs). Six e-waste products that contribute the most to the e-waste in Jordan were included in the assessment of each scenario, which resulted in 30 total cases of e-waste management. The findings indicated that landfills for the entire components of the e-waste stream are the worst option and should be avoided. The most promising e-waste management scenario features integrated e-waste processes based on the concept of Integrated Waste Management (IWM), including recycling materials such as non-PMs and PMs, incinerating plastic and the hazardous content of PCBs using the energy recovered from incineration, and using sanitary landfills of residues. For this scenario, the best environmental performance was obtained for the treatment of mobile phones. Incineration of the portion of hazardous waste using energy recovery is an option that deserves attention. Because scenario implementation depends on more than just the environmental benefits (e.g., economic cost and technical aspects), the study proposes a systematic approach founded on the IWM concept for e-waste management scenario selection. Copyright © 2017 Elsevier Ltd. All rights reserved.

Exploring Secondary School Students' Understanding and Practices of Waste Management in Ogun State, Nigeria

ERIC Educational Resources Information Center

Ifegbesan, Ayodeji

2010-01-01

This study examined the level of awareness, knowledge and practices of secondary schools students with regard to waste management. Few studies have captured waste management problems in Nigerian educational institutions, particularly the views of students. Using a structured, self-administered questionnaire, 650 students were surveyed from six…

Indicators of waste management efficiency related to different territorial conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Passarini, Fabrizio, E-mail: fabrizio.passarini@unibo.it; Vassura, Ivano, E-mail: ivano.vassura@unibo.it; Monti, Francesco, E-mail: fmonti84@gmail.com

2011-04-15

The amount of waste produced and the control of separate collection are crucial issues for the planning of a territorial Integrated Waste Management System, enabling the allocation of each sorted waste fraction to the proper treatment and recycling processes. The present study focuses on assessing indicators of different waste management systems in areas characterized by different territorial conditions. The investigated case study concerns the municipalities of Emilia Romagna (northern Italy), which present a rather uniform socioeconomic situation, but a variety of geographic, urban and waste management characteristics. A survey of waste generation and collection rates was carried out, and correlatedmore » with the different territorial conditions, classifying the municipalities according to altitude and population density. The best environmental performances, in terms of high separate collection rate, were found on average in rural areas in the plain, while the lowest waste generation was associated with rural hill towns.« less

[Assessment of medical waste management in a Palestinian hospital].

PubMed

Al-Khatib, I A; Khatib, R A

2006-01-01

We studied medical waste management in a Palestinian hospital in the West Bank and the role of municipality in this management. In general, "good management practices" were inadequate; there was insufficient separation between hazardous and non-hazardous wastes, an absence of necessary rules and regulations for the collection of wastes from the hospital wards and the on-site transport to a temporary storage location inside and outside the hospital and inadequate waste treatment and disposal of hospital wastes along with municipal garbage. Moreover, training of personnel was lacking and protective equipment and measures for staff were not available. No special landfills for hazardous wastes were found within the municipality.

Hospital waste management in Brazil: a case study.

PubMed

Mattoso, V D; Schalch, V

2001-12-01

The evaluation of the current definition, classification and quantification of hospital waste being carried out by hospitals in different countries is extremely important to avoid improper waste management practices. In this work, the waste management from a 400-bed Brazilian hospital which generates about 386 kg per day of hospital waste was studied. The generation rate of just over one kg per bed per day was considered small, although more than 50% of the waste from non-isolation wards consisted of food waste. It was also interesting to note that the highest generation rate per patient per day was found in private rooms and the lowest rate in the public ones. The waste practices used in this hospital are discussed in terms of current Brazilian legislation.

Rules and management of biomedical waste at Vivekananda Polyclinic: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, Saurabh; Boojh, Ram; Mishra, Ajai

Hospitals and other healthcare establishments have a 'duty of care' for the environment and for public health, and have particular responsibilities in relation to the waste they produce (i.e., biomedical waste). Negligence, in terms of biomedical waste management, significantly contributes to polluting the environment, affects the health of human beings, and depletes natural and financial resources. In India, in view of the serious situation of biomedical waste management, the Ministry of Environment and Forests, within the Government of India, ratified the Biomedical Waste (Management and Handling) Rules, in July 1998. The present paper provides a brief description of the biomedicalmore » waste (Management and Handling) Rules 1998, and the current biomedical waste management practices in one of the premier healthcare establishments of Lucknow, the Vivekananda Polyclinic. The objective in undertaking this study was to analyse the biomedical waste management system, including policy, practice (i.e., storage, collection, transportation and disposal), and compliance with the standards prescribed under the regulatory framework. The analysis consisted of interviews with medical authorities, doctors, and paramedical staff involved in the management of the biomedical wastes in the Polyclinic. Other important stakeholders that were consulted and interviewed included environmental engineers (looking after the Biomedical Waste Cell) of the State Pollution Control Board, and randomly selected patients and visitors to the Polyclinic. A general survey of the facilities of the Polyclinic was undertaken to ascertain the efficacy of the implemented measures. The waste was quantified based on random samples collected from each ward. It was found that, although the Polyclinic in general abides by the prescribed regulations for the treatment and disposal of biomedical waste, there is a need to further build the capacity of the Polyclinic and its staff in terms of providing state-of-the-art facilities and on-going training in order to develop a model biomedical waste management system in the Polyclinic. There is also a need to create awareness among all other stakeholders about the importance of biomedical waste management and related regulations. Furthermore, healthcare waste management should go beyond data compilation, enforcement of regulations, and acquisition of better equipment. It should be supported through appropriate education, training, and the commitment of the healthcare staff and management and healthcare managers within an effective policy and legislative framework.« less

Rules and management of biomedical waste at Vivekananda Polyclinic: a case study.

PubMed

Gupta, Saurabh; Boojh, Ram; Mishra, Ajai; Chandra, Hem

2009-02-01

Hospitals and other healthcare establishments have a "duty of care" for the environment and for public health, and have particular responsibilities in relation to the waste they produce (i.e., biomedical waste). Negligence, in terms of biomedical waste management, significantly contributes to polluting the environment, affects the health of human beings, and depletes natural and financial resources. In India, in view of the serious situation of biomedical waste management, the Ministry of Environment and Forests, within the Government of India, ratified the Biomedical Waste (Management and Handling) Rules, in July 1998. The present paper provides a brief description of the biomedical waste (Management and Handling) Rules 1998, and the current biomedical waste management practices in one of the premier healthcare establishments of Lucknow, the Vivekananda Polyclinic. The objective in undertaking this study was to analyse the biomedical waste management system, including policy, practice (i.e., storage, collection, transportation and disposal), and compliance with the standards prescribed under the regulatory framework. The analysis consisted of interviews with medical authorities, doctors, and paramedical staff involved in the management of the biomedical wastes in the Polyclinic. Other important stakeholders that were consulted and interviewed included environmental engineers (looking after the Biomedical Waste Cell) of the State Pollution Control Board, and randomly selected patients and visitors to the Polyclinic. A general survey of the facilities of the Polyclinic was undertaken to ascertain the efficacy of the implemented measures. The waste was quantified based on random samples collected from each ward. It was found that, although the Polyclinic in general abides by the prescribed regulations for the treatment and disposal of biomedical waste, there is a need to further build the capacity of the Polyclinic and its staff in terms of providing state-of-the-art facilities and on-going training in order to develop a model biomedical waste management system in the Polyclinic. There is also a need to create awareness among all other stakeholders about the importance of biomedical waste management and related regulations. Furthermore, healthcare waste management should go beyond data compilation, enforcement of regulations, and acquisition of better equipment. It should be supported through appropriate education, training, and the commitment of the healthcare staff and management and healthcare managers within an effective policy and legislative framework.

Disaster waste management in Italy: Analysis of recent case studies.

PubMed

Gabrielli, Francesco; Amato, Alessia; Balducci, Susanna; Magi Galluzzi, Lorenzo; Beolchini, Francesca

2018-01-01

The geomorphology of the Italian territory causes the incidence of many disasters like earthquakes and floods, with the consequent production of large volumes of waste. The management of such huge flows, produced in a very short time, may have a high impact on the whole emergency response. Moreover, historical data related to disaster waste management are often not easily accessible; on the other hand, the availability of data concerning previous events could support the emergency managers, that have to take a decision in a very short time. In this context, the present paper analyses four relevant recent case studies in Italy, dealing with disaster waste management after geologic and hydrologic natural events. Significant differences have been observed in the quantity and types of generated wastes, and, also, in the management approach. Such differences are mainly associated with the kind of disaster (i.e. earthquake vs. flood), to the geographical location (i.e. internal vs. coastal area), to the urbanisation level (i.e. industrial vs. urban). The study allowed the identification of both strengths and weaknesses of the applied waste management strategies, that represent "lessons to learn" for future scenarios. Even though it deals with Italian case studies, this manuscript may have a high impact also at international level, making available for the first-time emergency waste management data, that are considered an indispensable support for decision makers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Costs associated with the management of waste from healthcare facilities: An analysis at national and site level.

PubMed

Vaccari, Mentore; Tudor, Terry; Perteghella, Andrea

2018-01-01

Given rising spend on the provision of healthcare services, the sustainable management of waste from healthcare facilities is increasingly becoming a focus as a means of reducing public health risks and financial costs. Using data on per capita healthcare spend at the national level, as well as a case study of a hospital in Italy, this study examined the relationship between trends in waste generation and the associated costs of managing the waste. At the national level, healthcare spend as a percentage of gross domestic product positively correlated with waste arisings. At the site level, waste generation and type were linked to department type and clinical performance, with the top three highest generating departments of hazardous healthcare waste being anaesthetics (5.96 kg day -1 bed -1 ), paediatric and intensive care (3.37 kg day -1 bed -1 ) and gastroenterology-digestive endoscopy (3.09 kg day -1 bed -1 ). Annual overall waste management costs were $US5,079,191, or approximately $US2.36 kg -1 , with the management of the hazardous fraction of the waste being highest at $US3,707,939. In Italy, reduction in both waste arisings and the associated costs could be realised through various means, including improved waste segregation, and linking the TARI tax to waste generation.

Impact of intervention on healthcare waste management practices in a tertiary care governmental hospital of Nepal.

PubMed

Sapkota, Binaya; Gupta, Gopal Kumar; Mainali, Dhiraj

2014-09-26

Healthcare waste is produced from various therapeutic procedures performed in hospitals, such as chemotherapy, dialysis, surgery, delivery, resection of gangrenous organs, autopsy, biopsy, injections, etc. These result in the production of non-hazardous waste (75-95%) and hazardous waste (10-25%), such as sharps, infectious, chemical, pharmaceutical, radioactive waste, and pressurized containers (e.g., inhaler cans). Improper healthcare waste management may lead to the transmission of hepatitis B, Staphylococcus aureus and Pseudomonas aeruginosa. This evaluation of waste management practices was carried out at gynaecology, obstetrics, paediatrics, medicine and orthopaedics wards at Government of Nepal Civil Service Hospital, Kathmandu from February 12 to October 15, 2013, with the permission from healthcare waste management committee at the hospital. The Individualized Rapid Assessment tool (IRAT), developed by the United Nations Development Program Global Environment Facility project, was used to collect pre-interventional and post-interventional performance scores concerning waste management. The healthcare waste management committee was formed of representing various departments. The study included responses from focal nurses and physicians from the gynaecology, obstetrics, paediatrics, medicine and orthopaedics wards, and waste handlers during the study period. Data included average scores from 40 responders. Scores were based on compliance with the IRAT. The waste management policy and standard operating procedure were developed after interventions, and they were consistent with the national and international laws and regulations. The committee developed a plan for recycling or waste minimization. Health professionals, such as doctors, nurses and waste handlers, were trained on waste management practices. The programs included segregation, collection, handling, transportation, treatment and disposal of waste, as well as occupational health and safety issues. The committee developed a plan for treatment and disposal of chemical and pharmaceutical waste. Pretest and posttest evaluation scores were 26% and 86% respectively. During the pre-intervention period, the hospital had no HCWM Committee, policy, standard operating procedure or proper color coding system for waste segregation, collection, transportation and storage and the specific well-trained waste handlers. Doctors, nurses and waste handlers were trained on HCWM practices, after interventions. Significant improvements were observed between the pre- and post-intervention periods.

Report: Hospital waste management--awareness and practices: a study of three states in India.

PubMed

Rao, P Hanumantha

2008-06-01

The study was conducted in Andhra Pradesh, Maharashtra and Uttar Pradesh in India. Hospitals/nursing homes and private medical practitioners in urban as well as rural areas and those from the private as well as the government sector were covered. Information on (a) awareness of bio-medical waste management rules, (b) training undertaken and (c) practices with respect to segregation, use of colour coding, sharps management, access to common waste management facilities and disposal was collected. Awareness of Bio-medical Waste Management Rules was better among hospital staff in comparison with private medical practitioners and awareness was marginally higher among those in urban areas in comparison with those in rural areas. Training gained momentum only after the dead-line for compliance was over. Segregation and use of colour codes revealed gaps, which need correction. About 70% of the healthcare facilities used a needle cutter/destroyer for sharps management. Access to Common Waste Management facilities was low at about 35%. Dumping biomedical waste on the roads outside the hospital is still prevalent and access to Common Waste facilities is still limited. Surveillance, monitoring and penal machinery was found to be deficient and these require strengthening to improve compliance with the Bio-medical Waste Management Rules and to safeguard the health of employees, patients and communities.

The role of waste bank partnership in efforts to decrease waste volume in urban: A case study at a waste bank in Kalibaru, Cilodong, Depok City

NASA Astrophysics Data System (ADS)

Suparmini; Junadi, Purnawan

2018-03-01

Waste Bank is a program that the government uses as one of the efforts to tackle the increasingly growing garbage day. The Waste Bank in Depok City serves as a collection of non-organic waste that still has economic value. This study attempts to examine the factors that make Depok City Waste Bank play its role today and its relationship with the community involved in the activities of the Waste Bank. Through qualitative approach with a case study, the authors make observations on the object and conduct in-depth interviews with some informants. This study found four factors that make a Waste Bank continues to play a role, namely the presence of leaders who are reliable (leadership), good management (management), incentive (incentive) and the involvement of partners (partnership). While the characteristics of community-based on the level of education, income levels also affect the community participation in receiving the Waste Bank as a form of waste management in the city of Depok.

Closed Fuel Cycle Waste Treatment Strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vienna, J. D.; Collins, E. D.; Crum, J. V.

This study is aimed at evaluating the existing waste management approaches for nuclear fuel cycle facilities in comparison to the objectives of implementing an advanced fuel cycle in the U.S. under current legal, regulatory, and logistical constructs. The study begins with the Global Nuclear Energy Partnership (GNEP) Integrated Waste Management Strategy (IWMS) (Gombert et al. 2008) as a general strategy and associated Waste Treatment Baseline Study (WTBS) (Gombert et al. 2007). The tenets of the IWMS are equally valid to the current waste management study. However, the flowsheet details have changed significantly from those considered under GNEP. In addition, significantmore » additional waste management technology development has occurred since the GNEP waste management studies were performed. This study updates the information found in the WTBS, summarizes the results of more recent technology development efforts, and describes waste management approaches as they apply to a representative full recycle reprocessing flowsheet. Many of the waste management technologies discussed also apply to other potential flowsheets that involve reprocessing. These applications are occasionally discussed where the data are more readily available. The report summarizes the waste arising from aqueous reprocessing of a typical light-water reactor (LWR) fuel to separate actinides for use in fabricating metal sodium fast reactor (SFR) fuel and from electrochemical reprocessing of the metal SFR fuel to separate actinides for recycle back into the SFR in the form of metal fuel. The primary streams considered and the recommended waste forms include; Tritium in low-water cement in high integrity containers (HICs); Iodine-129: As a reference case, a glass composite material (GCM) formed by the encapsulation of the silver Mordenite (AgZ) getter material in a low-temperature glass is assumed. A number of alternatives with distinct advantages are also considered including a fused silica waste form with encapsulated nano-sized AgI crystals; Carbon-14 immobilized as a CaCO3 in a cement waste form; Krypton-85 stored as a compressed gas; An aqueous reprocessing high-level waste (HLW) raffinate waste immobilized by the vitrification process; An undissolved solids (UDS) fraction from aqueous reprocessing of LWR fuel either included in the borosilicate HLW glass or immobilized in the form of a metal alloy or titanate ceramics; Zirconium-based LWR fuel cladding hulls and stainless steel (SS) fuel assembly hardware super-compacted for disposal or purified for reuse (or disposal as low-level waste, LLW) of Zr by reactive gas separations; Electrochemical process salt HLW incorporated into a glass bonded Sodalite waste form; and Electrochemical process UDS and SS cladding hulls melted into an iron based alloy waste form. Mass and volume estimates for each of the recommended waste forms based on the source terms from a representative flowsheet are reported. In addition to the above listed primary waste streams, a range of secondary process wastes are generated by aqueous reprocessing of LWR fuel, metal SFR fuel fabrication, and electrochemical reprocessing of SFR fuel. These secondary wastes have been summarized and volumes estimated by type and classification. The important waste management data gaps and research needs have been summarized for each primary waste stream and selected waste process.« less

Optimization of greenhouse gas emissions in second-hand consumer product recovery through reuse platforms.

PubMed

Fortuna, Lorena M; Diyamandoglu, Vasil

2017-08-01

Product reuse in the solid waste management sector is promoted as one of the key strategies for waste prevention. This practice is considered to have favorable impact on the environment, but its benefits have yet to be established. Existing research describes the perspective of "avoided production" only, but has failed to examine the interdependent nature of reuse practices within an entire solid waste management system. This study proposes a new framework that uses optimization to minimize the greenhouse gas emissions of an integrated solid waste management system that includes reuse strategies and practices such as reuse enterprises, online platforms, and materials exchanges along with traditional solid waste management practices such as recycling, landfilling, and incineration. The proposed framework uses material flow analysis in combination with an optimization model to provide the best outcome in terms of GHG emissions by redistributing product flows in the integrated solid waste management system to the least impacting routes and processes. The optimization results provide a basis for understanding the contributions of reuse to the environmental benefits of the integrated solid waste management system and the exploration of the effects of reuse activities on waste prevention. A case study involving second-hand clothing is presented to illustrate the implementation of the proposed framework as applied to the material flow. Results of the case study showed the considerable impact of reuse on GHG emissions even for small replacement rates, and helped illustrate the interdependency of the reuse sector with other waste management practices. One major contribution of this study is the development of a framework centered on product reuse that can be applied to identify the best management strategies to reduce the environmental impact of product disposal and to increase recovery of reusable products. Copyright © 2017 Elsevier Ltd. All rights reserved.

A systematic critical review of epidemiological studies on public health concerns of municipal solid waste handling.

PubMed

Ncube, France; Ncube, Esper Jacobeth; Voyi, Kuku

2017-03-01

The ultimate aim of this review was to summarise the epidemiological evidence on the association between municipal solid waste management operations and health risks to populations residing near landfills and incinerators, waste workers and recyclers. To accomplish this, the sub-aims of this review article were to (1) examine the health risks posed by municipal solid waste management activities, (2) determine the strengths and gaps of available literature on health risks from municipal waste management operations and (3) suggest possible research needs for future studies. The article reviewed epidemiological literature on public health concerns of municipal solid waste handling published in the period 1995-2014. The PubMed and MEDLINE computerised literature searches were employed to identify the relevant papers using the keywords solid waste, waste management, health risks, recycling, landfills and incinerators. Additionally, all references of potential papers were examined to determine more articles that met the inclusion criteria. A total of 379 papers were identified, but after intensive screening only 72 met the inclusion criteria and were reviewed. Of these studies, 33 were on adverse health effects in communities living near waste dumpsites or incinerators, 24 on municipal solid waste workers and 15 on informal waste recyclers. Reviewed studies were unable to demonstrate a causal or non-causal relationship due to various limitations. In light of the above findings, our review concludes that overall epidemiological evidence in reviewed articles is inadequate mainly due to methodological limitations and future research needs to develop tools capable of demonstrating causal or non-causal relationships between specific waste management operations and adverse health endpoints.

Multi-criteria decision making to support waste management: A critical review of current practices and methods.

PubMed

Goulart Coelho, Lineker M; Lange, Liséte C; Coelho, Hosmanny Mg

2017-01-01

Solid waste management is a complex domain involving the interaction of several dimensions; thus, its analysis and control impose continuous challenges for decision makers. In this context, multi-criteria decision-making models have become important and convenient supporting tools for solid waste management because they can handle problems involving multiple dimensions and conflicting criteria. However, the selection of the multi-criteria decision-making method is a hard task since there are several multi-criteria decision-making approaches, each one with a large number of variants whose applicability depends on information availability and the aim of the study. Therefore, to support researchers and decision makers, the objectives of this article are to present a literature review of multi-criteria decision-making applications used in solid waste management, offer a critical assessment of the current practices, and provide suggestions for future works. A brief review of fundamental concepts on this topic is first provided, followed by the analysis of 260 articles related to the application of multi-criteria decision making in solid waste management. These studies were investigated in terms of the methodology, including specific steps such as normalisation, weighting, and sensitivity analysis. In addition, information related to waste type, the study objective, and aspects considered was recorded. From the articles analysed it is noted that studies using multi-criteria decision making in solid waste management are predominantly addressed to problems related to municipal solid waste involving facility location or management strategy.

Household waste compositional analysis variation from insular communities in the framework of waste prevention strategy plans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zorpas, Antonis A., E-mail: antonis.zorpas@ouc.ac.cy; Lasaridi, Katia, E-mail: klasaridi@hua.gr; Voukkali, Irene

Highlights: • Waste framework directive has set clear waste prevention procedures. • Household Compositional analysis. • Waste management plans. • Zero waste approach. • Waste generation. - Abstract: Waste management planning requires reliable data regarding waste generation, affecting factors on waste generation and forecasts of waste quantities based on facts. In order to decrease the environmental impacts of waste management the choice of prevention plan as well as the treatment method must be based on the features of the waste that are produced in a specific area. Factors such as culture, economic development, climate, and energy sources have an impactmore » on waste composition; composition influences the need of collecting waste more or less frequently of waste collection and disposition. The research question was to discover the main barriers concerning the compositional analysis in Insular Communities under warm climate conditions and the findings from this study enabled the main contents of a waste management plan to be established. These included advice to residents on waste minimisation, liaison with stakeholders and the expansion of kerbside recycling schemes.« less

A study on the attitudes and behavioural influence of construction waste management in occupied Palestinian territory.

PubMed

Al-Sari, Majed I; Al-Khatib, Issam A; Avraamides, Marios; Fatta-Kassinos, Despo

2012-02-01

As a step towards comprehending what drives the management of construction waste in the occupied Palestinian territory, this paper quantifies construction waste generation and examines how the local contractors' waste management attitudes and behaviour are influenced. Collection of data was based on a survey, carried out in the southern part of the West Bank between April and May 2010. The survey targeted contractors who specialized in the construction of buildings. A logistic regression model was used to investigate the relationship between various attributes and the attitudes and behaviour that the local contractors demonstrate towards waste management. The results showed that during the construction of buildings, 17 to 81 kg of construction waste are generated per square metre of building floor. Although the area of a building is the key factor determining 74.8% of the variation of construction waste generation, the employment of labour-intensive techniques in the study area means that human factors such as the contractor's attitude and behaviour towards waste management, exert a key influence on waste generation. Attitudes towards the 3Rs of waste minimization and behaviour towards waste disposal are generally positive with smaller contractors exhibiting more positive attitudes and more satisfactory behaviour towards waste management. Overall, while contractors' behaviour towards waste sorting and disposal tends to be more satisfactory among contractors who are more conscious about the potential environmental impacts of construction waste, it was generally observed that in the absence of a regulatory framework, the voluntary attitudes and behaviour among the local contractors are mostly driven by direct economic considerations.

Using a contingent valuation approach for improved solid waste management facility: Evidence from Kuala Lumpur, Malaysia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Afroz, Rafia, E-mail: rafia_afroz@yahoo.com; Masud, Muhammad Mehedi

2011-04-15

This study employed contingent valuation method to estimate the willingness to pay (WTP) of the households to improve the waste collection system in Kuala Lumpur, Malaysia. The objective of this study is to evaluate how household WTP changes when recycling and waste separation at source is made mandatory. The methodology consisted of asking people directly about their WTP for an additional waste collection service charge to cover the costs of a new waste management project. The new waste management project consisted of two versions: version A (recycling and waste separation is mandatory) and version B (recycling and waste separation ismore » not mandatory). The households declined their WTP for version A when they were asked to separate the waste at source although all the facilities would be given to them for waste separation. The result of this study indicates that the households were not conscious about the benefits of recycling and waste separation. Concerted efforts should be taken to raise environmental consciousness of the households through education and more publicity regarding waste separation, reducing and recycling.« less

Review of LCA studies of solid waste management systems – Part I: Lessons learned and perspectives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laurent, Alexis, E-mail: alau@dtu.dk; Bakas, Ioannis; Clavreul, Julie

Highlights: • We perform a critical review of 222 LCA studies of solid waste management systems. • Studies mainly concentrated in Europe with little application in developing countries. • Assessments of relevant waste types apart from household waste have been overlooked. • Local specificities of systems prevent a meaningful generalisation of the LCA results. • LCA should support recommendations representative of the local conditions. - Abstract: The continuously increasing solid waste generation worldwide calls for management strategies that integrate concerns for environmental sustainability. By quantifying environmental impacts of systems, life cycle assessment (LCA) is a tool, which can contribute tomore » answer that call. But how, where and to which extent has it been applied to solid waste management systems (SWMSs) until now, and which lessons can be learnt from the findings of these LCA applications? To address these questions, we performed a critical review of 222 published LCA studies of SWMS. We first analysed the geographic distribution and found that the published studies have primarily been concentrated in Europe with little application in developing countries. In terms of technological coverage, they have largely overlooked application of LCA to waste prevention activities and to relevant waste types apart from household waste, e.g. construction and demolition waste. Waste management practitioners are thus encouraged to abridge these gaps in future applications of LCA. In addition to this contextual analysis, we also evaluated the findings of selected studies of good quality and found that there is little agreement in the conclusions among them. The strong dependence of each SWMS on local conditions, such as waste composition or energy system, prevents a meaningful generalisation of the LCA results as we find it in the waste hierarchy. We therefore recommend stakeholders in solid waste management to regard LCA as a tool, which, by its ability of capturing the local specific conditions in the modelling of environmental impacts and benefits of a SWMS, allows identifying critical problems and proposing improvement options adapted to the local specificities.« less

Management of Biomedical Waste: An Exploratory Study.

PubMed

Abhishek, K N; Suryavanshi, Harshal N; Sam, George; Chaithanya, K H; Punde, Prashant; Singh, S Swetha

2015-09-01

Dental operatories pose a threat due to the high chances of infection transmission both to the clinician and the patients. Hence, management of dental waste becomes utmost importance not only for the health benefit of the dentist himself, but also people who can come into contact with these wastes directly or indirectly. The present study was conducted to find out the management of biomedical waste in private dental practice among 3 districts of Karnataka. The study population included 186 private practitioners in 3 districts of Karnataka (Coorg, Mysore, Hassan), South India. A pre-tested self-administered questionnaire was distributed to assess the knowledge and practices regarding dental waste management. Descriptive statistics was used to summarize the results. Out of 186 study subjects, 71 (38%) were females and 115 (62%) were males. The maximum number of participants belonged to the age group of 28-33 years (29%). Undergraduate qualification was more (70%). 90 (48%) participants had an experience of 0-5 years. Chi-square analysis showed a highly significant association between participant who attended continuing dental education (CDE) program and their practice of dental waste management. Education with regards to waste management will help in enhancing practices regarding the same. In order to fill this vacuum CDE programs have to be conducted in pursuance to maintain health of the community.

The effect of food waste disposers on municipal waste and wastewater management.

PubMed

Marashlian, Natasha; El-Fadel, Mutasem

2005-02-01

This paper examines the feasibility of introducing food waste disposers as a waste minimization option within urban waste management schemes, taking the Greater Beirut Area (GBA) as a case study. For this purpose, the operational and economic impacts of food disposers on the solid waste and wastewater streams are assessed. The integration of food waste disposers can reduce the total solid waste to be managed by 12 to 43% under market penetration ranging between 25 and 75%, respectively. While the increase in domestic water consumption (for food grinding) and corresponding increase in wastewater flow rates are relatively insignificant, wastewater loadings increased by 17 to 62% (BOD) and 1.9 to 7.1% (SS). The net economic benefit of introducing food disposers into the waste and wastewater management systems constitutes 7.2 to 44.0% of the existing solid waste management cost under the various scenarios examined. Concerns about increased sludge generation persist and its potential environmental and economic implications may differ with location and therefore area-specific characteristics must be taken into consideration when contemplating the adoption of a strategy to integrate food waste disposers in the waste-wastewater management system.

The Management of Chemical Waste in a University Setting.

ERIC Educational Resources Information Center

Coons, David Michael

This thesis describes a study of the management of chemical waste at the State University of New York at Binghamton. The study revealed that the majority of chemical waste at the university is in the form of hazardous waste. It was hypothesized that the volume, related costs, and potential long-term liability associated with the disposal of…

A Model of Solid Waste Management Based Multilateral Co-Operation in Semi-Urban Community

ERIC Educational Resources Information Center

Kanchanabhandhu, Chanchai; Woraphong, Seree

2016-01-01

The purpose of this research was to construct a model of solid waste management based on multilateral cooperation in semi-urban community. Its specific objectives were to 1) study the solid waste situation and involvement of community in the solid waste management in Wangtaku Sub-district, Muang District, Nakhon Pathom Province; 2) construct a…

The use of multi-criteria decision analysis to tackle waste management problems: a literature review.

PubMed

Achillas, Charisios; Moussiopoulos, Nicolas; Karagiannidis, Avraam; Banias, Georgias; Perkoulidis, George

2013-02-01

Problems in waste management have become more and more complex during recent decades. The increasing volumes of waste produced and social environmental consciousness present prominent drivers for environmental managers towards the achievement of a sustainable waste management scheme. However, in practice, there are many factors and influences - often mutually conflicting - criteria for finding solutions in real-life applications. This paper presents a review of the literature on multi-criteria decision aiding in waste management problems for all reported waste streams. Despite limitations, which are clearly stated, most of the work published in this field is reviewed. The present review aims to provide environmental managers and decision-makers with a thorough list of practical applications of the multi-criteria decision analysis techniques that are used to solve real-life waste management problems, as well as the criteria that are mostly employed in such applications according to the nature of the problem under study. Moreover, the paper explores the advantages and disadvantages of using multi-criteria decision analysis techniques in waste management problems in comparison to other available alternatives.

Integrated management of hazardous waste generated from community sources in Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yodnane, P.; Spaeder, D.J.

A system for the collection, transport, disposal and recycling of hazardous waste was developed as part of an overall master plan for the management of hazardous waste generated from community sources in Thailand. Results of a waste generation survey conducted as part of the study indicated that over 300 million kilograms per year of hazardous waste is generated from non-industrial, community sources such as automotive repair shops, gas stations, hospitals, farms, and households in Thailand. Hazardous waste from community sources consists primarily of used oils, lead-acid and dry cell batteries, cleaning chemicals, pesticides, medical wastes, solvents and fuels. Most ofmore » this waste was found to be mismanaged by codisposing with municipal waste in burning, unlined dumps, dumping directly to land or water courses, dumping into sewers, or recycling improperly, all of which pose serious threats to human health and the environment. The survey data on waste generation quantities and data from a reconnaissance survey of the conditions and operations of 86 existing waste disposal facilities was incorporated into a nationwide Geographic Information System (GIS) database. Based on this data, problems associated with hazardous waste were identified and needs for waste management systems were tabulated. A system was developed for ranking geographic regions according to hazardous waste management problems and needs, in order to prioritize implementation of waste management programs. The data were also used in developing solutions for hazardous waste management, which addressed methods for storing, collecting, transporting, disposing, and recycling the waste. It was recommended that centralized waste management facilities be utilized which included hazardous waste and medical waste incinerators, waste stabilization units, and secure landfills.« less

Factors Influencing Attitude, Safety Behavior, and Knowledge regarding Household Waste Management in Guinea: A Cross-Sectional Study

PubMed Central

Mamady, Keita

2016-01-01

Waste indiscriminate disposal is recognized as an important cause of environmental pollution and is associated with health problems. Safe management and disposal of household waste are an important problem to the capital city of Guinea (Conakry). The objective of this study was to identify socioeconomic and demographic factors associated with practice, knowledge, and safety behavior of family members regarding household waste management and to produce a remedial action plan. I found that no education background, income, and female individuals were independently associated with indiscriminate waste disposal. Unplanned residential area was an additional factor associated with indiscriminate waste disposal. I also found that the community residents had poor knowledge and unsafe behavior in relation to waste management. The promotion of environmental information and public education and implementation of community action programs on disease prevention and health promotion will enhance environmental friendliness and safety of the community. PMID:27092183

Factors Influencing Attitude, Safety Behavior, and Knowledge regarding Household Waste Management in Guinea: A Cross-Sectional Study.

PubMed

Mamady, Keita

2016-01-01

Waste indiscriminate disposal is recognized as an important cause of environmental pollution and is associated with health problems. Safe management and disposal of household waste are an important problem to the capital city of Guinea (Conakry). The objective of this study was to identify socioeconomic and demographic factors associated with practice, knowledge, and safety behavior of family members regarding household waste management and to produce a remedial action plan. I found that no education background, income, and female individuals were independently associated with indiscriminate waste disposal. Unplanned residential area was an additional factor associated with indiscriminate waste disposal. I also found that the community residents had poor knowledge and unsafe behavior in relation to waste management. The promotion of environmental information and public education and implementation of community action programs on disease prevention and health promotion will enhance environmental friendliness and safety of the community.

An Attempt at Quantifying Factors that Affect Efficiency in the Management of Solid Waste Produced by Commercial Businesses in the City of Tshwane, South Africa

PubMed Central

Worku, Yohannes; Muchie, Mammo

2012-01-01

Objective. The objective was to investigate factors that affect the efficient management of solid waste produced by commercial businesses operating in the city of Pretoria, South Africa. Methods. Data was gathered from 1,034 businesses. Efficiency in solid waste management was assessed by using a structural time-based model designed for evaluating efficiency as a function of the length of time required to manage waste. Data analysis was performed using statistical procedures such as frequency tables, Pearson's chi-square tests of association, and binary logistic regression analysis. Odds ratios estimated from logistic regression analysis were used for identifying key factors that affect efficiency in the proper disposal of waste. Results. The study showed that 857 of the 1,034 businesses selected for the study (83%) were found to be efficient enough with regards to the proper collection and disposal of solid waste. Based on odds ratios estimated from binary logistic regression analysis, efficiency in the proper management of solid waste was significantly influenced by 4 predictor variables. These 4 influential predictor variables are lack of adherence to waste management regulations, wrong perception, failure to provide customers with enough trash cans, and operation of businesses by employed managers, in a decreasing order of importance. PMID:23209483

Applying multi-criteria decision-making to improve the waste reduction policy in Taiwan.

PubMed

Su, Jun-Pin; Hung, Ming-Lung; Chao, Chia-Wei; Ma, Hwong-wen

2010-01-01

Over the past two decades, the waste reduction problem has been a major issue in environmental protection. Both recycling and waste reduction policies have become increasingly important. As the complexity of decision-making has increased, it has become evident that more factors must be considered in the development and implementation of policies aimed at resource recycling and waste reduction. There are many studies focused on waste management excluding waste reduction. This study paid more attention to waste reduction. Social, economic, and management aspects of waste treatment policies were considered in this study. Further, a life-cycle assessment model was applied as an evaluation system for the environmental aspect. Results of both quantitative and qualitative analyses on the social, economic, and management aspects were integrated via the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) method into the comprehensive decision-making support system of multi-criteria decision-making (MCDM). A case study evaluating the waste reduction policy in Taoyuan County is presented to demonstrate the feasibility of this model. In the case study, reinforcement of MSW sorting was shown to be the best practice. The model in this study can be applied to other cities faced with the waste reduction problems.

Solid waste management in Linamon, Lanao del Norte

NASA Astrophysics Data System (ADS)

Paragoso, Glaiza P.; Sapar, Cherine Mae A.; Magsayo, Joy R.; Lahoylahoy, Myrna E.; Guarin, Rica Mae B.

2018-01-01

In this modern world, Solid Waste Management is very important in maintaining a high quality of life so humans must manage and store waste efficiently and safely. Almost every day each household generates garbage or wastes. People throw things improperly without knowing the consequences. The main objective of the study was to assess the residents' Solid Waste Management. Specifically, it aimed to answer the following questions: What is the profile of the respondents in terms of age, gender, educational attainment, occupation, monthly income, no. of household member; What is the knowledge of the respondents about Natural Environment?; How do respondents disposed garbage from the household?; What is the level of the respondents concern about proper waste management?; What is the willingness of the respondents to participate in proper Solid Waste Management?; What is the attitude of the respondents towards the Solid Waste Management? The said study was conducted at the Municipality of Linamon, which is a 5th class municipality located at the Eastern Gateway to Lanao del Norte, a south western Province of Northern Mindanao in the Philippines. The study was conducted in the 8 barangays of the Municipality of Linamon, namely: Bosque, Larapan, Mago-ong, Napo, Poblacion, Purakan, Robocon, and Samburon. The Municipality has 3 urban barangays and 4 rural barangays. The study revealed that most of the respondents interviewed were housewives. Out of 313 respondents, 67.10 % did not understand the term natural environment, with major issue currently affecting natural environment as "household garbage'. The respondents dispose the yard trimmings and papers through burning. The plastic and glass is disposed through the garbage truck. The metals and damaged home appliances were disposed by selling it to the junk shop. The respondents disposed their garbage into an open container specifically in a sack, collected by garbage trucks. The study also revealed that the respondents were highly concerned about waste management and willing to participate in proper solid waste management, with attitudes towards solid waste management as highly positive. The researchers recommend initiating educational campaigns for the general public to raise awareness of the natural environment in order to fully understand the term. Incorporate environmental education into school curriculum to raise awareness and develop environmental attitudes in the large youth community.

Municipal solid waste management in Malaysia: practices and challenges.

PubMed

Manaf, Latifah Abd; Samah, Mohd Armi Abu; Zukki, Nur Ilyana Mohd

2009-11-01

Rapid economic development and population growth, inadequate infrastructure and expertise, and land scarcity make the management of municipal solid waste become one of Malaysia's most critical environmental issues. The study is aimed at evaluating the generation, characteristics, and management of solid waste in Malaysia based on published information. In general, the per capita generation rate is about 0.5-0.8 kg/person/day in which domestic waste is the primary source. Currently, solid waste is managed by the Ministry of Housing and Local Government, with the participation of the private sector. A new institutional and legislation framework has been structured with the objectives to establish a holistic, integrated, and cost-effective solid waste management system, with an emphasis on environmental protection and public health. Therefore, the hierarchy of solid waste management has given the highest priority to source reduction through 3R, intermediate treatment and final disposal.

An Exploration of Healthcare Inventory and Lean Management in Minimizing Medical Supply Waste in Healthcare Organizations

ERIC Educational Resources Information Center

Hicks, Rodney

2013-01-01

The purpose of this study was to understand how lean thinking and inventory management technology minimize expired medical supply waste in healthcare organizations. This study was guided by Toyota's theory of lean and Mintzberg's theory of management development to explain why the problem of medical supply waste exists. Government…

A system dynamics approach for hospital waste management in a city in a developing country: the case of Nablus, Palestine.

PubMed

Al-Khatib, Issam A; Eleyan, Derar; Garfield, Joy

2016-09-01

Hospitals and health centers provide a variety of healthcare services and normally generate hazardous waste as well as general waste. General waste has a similar nature to that of municipal solid waste and therefore could be disposed of in municipal landfills. However, hazardous waste poses risks to public health, unless it is properly managed. The hospital waste management system encompasses many factors, i.e., number of beds, number of employees, level of service, population, birth rate, fertility rate, and not in my back yard (NIMBY) syndrome. Therefore, this management system requires a comprehensive analysis to determine the role of each factor and its influence on the whole system. In this research, a hospital waste management simulation model is presented based on the system dynamics technique to determine the interaction among these factors in the system using a software package, ithink. This model is used to estimate waste segregation as this is important in the hospital waste management system to minimize risk to public health. Real data has been obtained from a case study of the city of Nablus, Palestine to validate the model. The model exhibits wastes generated from three types of hospitals (private, charitable, and government) by considering the number of both inpatients and outpatients depending on the population of the city under study. The model also offers the facility to compare the total waste generated among these different types of hospitals and anticipate and predict the future generated waste both infectious and non-infectious and the treatment cost incurred.

Certain Hospital Waste Management Practices in Isfahan, Iran

PubMed Central

Ferdowsi, Ali; Ferdosi, Masoud; Mehrani, Zeinab; Narenjkar, Parisa

2012-01-01

Objectives: Infected hospital wastes are among hazardous wastes, and special treatment methods are needed for their disposal. Having information about present status of medical waste management systems is of great importance in finding weak, and for future planning. Such studies have not been done for most of the hospitals in Iran. Methods: This paper reports the results of a study on the present status of medical waste management in Isfahan hospitals. A ten page researcher made questionnaire was used to collect data in terms of collection, transportation, segregation, treatment and disposal. For assessment of autoclaves, standard tests including TST (Time, Steam, and Temperature) strip test and spore tests were used. Samples were made of stack gases of incinerators. Quantity and composition of hospital wastes in Isfahan were also measured manually. Results: Of all wastes in selected hospitals, 40% were infected wastes (1.59 kg/day/bed), which is 15 to 20% higher than World Health Organization (WHO) standards. TST and Spore test results were negative in all samples. Stack gases analysis showed high concentration of CO in some samples. Besides, the combustion efficiency in some samples is less than 99.5%, which is the standard criterion in Iran. Conclusions: This study may create awareness regarding the magnitude of the problem of waste management in hospitals of Isfahan and may stimulate interests for systematic control efforts for hospital waste disposal. Hospital waste management cannot succeed without documented plans, certain equipment, defined staff trainings, and periodic evaluations. PMID:22826762

Healthcare waste management practice in the West Black Sea Region, Turkey: A comparative analysis with the developed and developing countries.

PubMed

Ciplak, Nesli; Kaskun, Songul

2015-12-01

The need for proper healthcare waste management has been a crucial issue in many developing countries as it is in Turkey. The regulation regarding healthcare wastes in Turkey was updated in 2005 in accordance with the European Union (EU) waste directives, but it still falls behind meeting the requirements of current waste treatment technologies. Therefore, this study aims to reveal deficiencies, inconsistencies, and improper applications of healthcare waste management in the western part of the Turkish Black Sea Region. In this study, it was revealed that nearly 1 million people live in the region, resulting in 5 million hospital admissions annually. All the healthcare waste produced (1000 tons yr(-1)) is treated in an autoclave plant. However, treating some categories of healthcare wastes in autoclave units mismatches with the EU waste regulations, as alternative treatment technologies are not technically able to treat all types of healthcare wastes. A proper waste management system, therefore, requires an internal segregation scheme to divert these wastes from the main healthcare waste stream. The existing malpractice in the region could cause serious health problems if no measure is taken urgently. It is expected that healthcare waste management in the region and then all across Turkey will be improved with the significant deficiencies and inconsistencies pointed out in this research. In developed countries, specific rules and regulations have already been implemented along with the recommendations for handling of healthcare waste. However, in Turkey, these wastes are treated in autoclave units, which mismatches with the European Union waste regulations, as alternative treatment technologies are not technically capable to treat all types of healthcare wastes. The existing malpractice could cause serious health problems if no measure is taken urgently. The authors demonstrated the existing status of Turkish waste management and revealed deficiencies, inconsistencies, and improper applications in comparison with developed and developing nations to align Turkish practice to European Union requirements.

Solid Waste Management Solutions for a Rapidly Urbanizing Area in Thailand: Recommendations Based on Stakeholder Input.

PubMed

Yukalang, Nachalida; Clarke, Beverley; Ross, Kirstin

2018-06-21

Municipal solid waste is a significant problem, particularly in developing countries that lack sufficient infrastructure and useable land mass to process it in an appropriate manner. Some developing nations are experiencing a combination of issues that prevent proper management of solid waste. This paper reviews the management of municipal solid waste in northeast Thailand, using the Tha Khon Yang Sub-district Municipality (TKYSM) in Maha Sarakham Province as a case study. The combination of rapid population and economic growth and its associated affluence has led to an increase in the use of consumer items and a concomitant increase in the production of municipal solid waste. In the TKYSM there is pressure on local government to establish a suitable waste management program to resolve the escalating waste crisis. The aim of this study is to provide viable solutions to waste management challenges in the TKYSM, and potentially to offer guidance to other similar localities also facing the same challenges. It is well established that successful changes to waste management require an understanding of local context and consideration of specific issues within a region. Therefore, extensive community consultation and engagement with local experts was undertaken to develop an understanding of the particular waste management challenges of the TKYSM. Research methods included observations, one-on-one interviews and focus groups with a range of different stakeholders. The outcomes of this research highlight a number of opportunities to improve local infrastructure and operational capacity around solid waste management. Waste management in rural and urban areas needs to be approached differently. Solutions include: development of appropriate policy and implementation plans (based around the recommendations of this paper); reduction of the volume of waste going to landfill by establishing a waste separation system; initiation of a collection service that supports waste separation at source; educating the citizens of the municipality; and the local government staff, and for the local government to seek external support from the local temples and expertise from the nearby university.

Solid waste management problems in secondary schools in Ibadan, Nigeria.

PubMed

Ana, G R E E; Oloruntoba, E O; Shendell, D; Elemile, O O; Benjamin, O R; Sridhar, M K C

2011-09-01

Inappropriate solid waste management practices in schools in less-developed countries, particularly in major urban communities, constitute one of the major factors leading to declining environmental health conditions. The objective of the authors' descriptive, cross-sectional study was to assess solid waste management problems in selected urban schools in Ibadan, Nigeria. Eight secondary schools with average pupil populations not less than 500 per school were selected randomly. Four hundred questionnaires (50 per school) were administered. In addition, an observational checklist was used to assess the physical environment. Paper and plastics were the most frequently generated wastes. Common methods of solid waste disposal reported were use of dustbins for collection and open burning. Major problems perceived with current refuse disposal methods by the study students were odors, pest infestation, and spillages. Littering and spillages of solid waste were also common features reported. Data suggested inadequate waste management facilities and practices in study schools. The lack of refuse bins may have contributed to waste spillages and the burning practices. Odors may have arisen from both the decay of overstored organic waste rich in moisture and emissions from refuse burning. This scenario poses a community environmental health nuisance and may compromise school environmental quality.

A multi-objective model for sustainable recycling of municipal solid waste.

PubMed

Mirdar Harijani, Ali; Mansour, Saeed; Karimi, Behrooz

2017-04-01

The efficient management of municipal solid waste is a major problem for large and populated cities. In many countries, the majority of municipal solid waste is landfilled or dumped owing to an inefficient waste management system. Therefore, an optimal and sustainable waste management strategy is needed. This study introduces a recycling and disposal network for sustainable utilisation of municipal solid waste. In order to optimise the network, we develop a multi-objective mixed integer linear programming model in which the economic, environmental and social dimensions of sustainability are concurrently balanced. The model is able to: select the best combination of waste treatment facilities; specify the type, location and capacity of waste treatment facilities; determine the allocation of waste to facilities; consider the transportation of waste and distribution of processed products; maximise the profit of the system; minimise the environmental footprint; maximise the social impacts of the system; and eventually generate an optimal and sustainable configuration for municipal solid waste management. The proposed methodology could be applied to any region around the world. Here, the city of Tehran, Iran, is presented as a real case study to show the applicability of the methodology.

Awareness about biomedical waste management and knowledge of effective recycling of dental materials among dental students.

PubMed

Ranjan, Rajeev; Pathak, Ruchi; Singh, Dhirendra K; Jalaluddin, Md; Kore, Shobha A; Kore, Abhijeet R

2016-01-01

Biomedical waste management has become a concern with increasing number of dental practitioners in India. Being health care professionals, dentists should be aware regarding safe disposal of biomedical waste and recycling of dental materials to minimize biohazards to the environment. The aim of the present study was to assess awareness regarding biomedical waste management as well as knowledge of effective recycling and reuse of dental materials among dental students. This cross-sectional study was conducted among dental students belonging from all dental colleges of Bhubaneswar, Odisha (India) from February 2016 to April 2016. A total of 500 students (208 males and 292 females) participated in the study, which was conducted in two phases. A questionnaire was distributed to assess the awareness of biomedical waste management and knowledge of effective recycling of dental materials, and collected data was examined on a 5-point unipolar scale in percentages to assess the relative awareness regarding these two different categorizes. The Statistical Package for Social Sciences was used to analyzed collected data. Forty-four percent of the dental students were not at all aware about the management of biomedical waste, 22% were moderately aware, 21% slightly aware, 7% very aware, and 5% fell in extremely aware category. Similarly, a higher percentage of participants (61%) were completely unaware regarding recycling and reusing of biomedical waste. There is lack of sufficient knowledge among dental students regarding management of biomedical waste and recycling or reusing of dental materials. Considering its impact on the environment, biomedical waste management requires immediate academic assessment to increase the awareness during training courses.

Dental solid and hazardous waste management and safety practices in developing countries: Nablus district, Palestine.

PubMed

Al-Khatib, Issam A; Monou, Maria; Mosleh, Salem A; Al-Subu, Mohammed M; Kassinos, Despo

2010-05-01

This study investigated the dental waste management practices and safety measures implemented by dentists in the Nablus district, Palestine. A comprehensive survey was conducted for 97 of the 134 dental clinics to assess the current situation. Focus was placed on hazardous waste produced by clinics and the handling, storage, treatment and disposal measures taken. Mercury, found in dental amalgam, is one of the most problematic hazardous waste. The findings revealed that there is no proper separation of dental waste by classification as demanded by the World Health Organization. Furthermore, medical waste is often mixed with general waste during production, collection and disposal. The final disposal of waste ends up in open dumping sites sometimes close to communities where the waste is burned. Correct management and safety procedures that could be effectively implemented in developing countries were examined. It was concluded that cooperation between dental associations, government-related ministries and authorities needs to be established, to enhance dental waste management and provide training and capacity building programs for all professionals in the medical waste management field.

Waste-efficient materials procurement for construction projects: A structural equation modelling of critical success factors.

PubMed

Ajayi, Saheed O; Oyedele, Lukumon O

2018-05-01

Albeit the understanding that construction waste is caused by activities ranging from all stages of project delivery process, research efforts have been concentrated on design and construction stages, while the possibility of reducing waste through materials procurement process is widely neglected. This study aims at exploring and confirming strategies for achieving waste-efficient materials procurement in construction activities. The study employs sequential exploratory mixed method approach as its methodological framework, using focus group discussion, statistical analysis and structural equation modelling. The study suggests that for materials procurement to enhance waste minimisation in construction projects, the procurement process would be characterised by four features. These include suppliers' commitment to low waste measures, low waste purchase management, effective materials delivery management and waste-efficient Bill of Quantity, all of which have significant impacts on waste minimisation. This implies that commitment of materials suppliers to such measures as take back scheme and flexibility in supplying small materials quantity, among others, are expected of materials procurement. While low waste purchase management stipulates the need for such measures as reduced packaging and consideration of pre-assembled/pre-cut materials, efficient delivery management entails effective delivery and storage system as well as adequate protection of materials during the delivery process, among others. Waste-efficient specification and bill of quantity, on the other hand, requires accurate materials take-off and ordering of materials based on accurately prepared design documents and bill of quantity. Findings of this study could assist in understanding a set of measures that should be taken during materials procurement process, thereby corroborating waste management practices at other stages of project delivery process. Copyright © 2018. Published by Elsevier Ltd.

Awareness of biomedical waste management among health care personnel in jaipur, India.

PubMed

Sharma, Alok; Sharma, Varsha; Sharma, Swati; Singh, Prabhat

2013-03-01

The study aimed to determine the following among the workforce of the Jaipur Dental College, India: their awareness regarding biomedical (BM) waste management policy and practices, their attitude towards biomedical waste management, and their awareness regarding needle-stick injury and its prevalence among different categories of health care providers. A cross-sectional study was conducted using a questionnaire with closed-ended questions. It was distributed to 144 dentists, nurses, laboratory technicians and Class IV employees (cleaners and maintenance personnel) at Jaipur Dental College. The questionnaire was used to assess their knowledge of biomedical medical waste disposal. The resulting answers were graded and the percentage of correct and incorrect answers for each question from all the participants was obtained. Of the 144 questionnaires, 140 were returned and the answers graded. The results showed that there was a poor level of knowledge and awareness of biomedical waste generation hazards, legislation and management among health care personnel. It was surprising that 36% of the nurses had an extremely poor knowledge of biomedical waste generation and legislation and just 15% of the Class IV employees had an excellent awareness of biomedical waste management practice. It can be concluded from the present study that there are poor levels of knowledge and awareness about BM waste generation hazards, legislation and management among health care personnel in Jaipur Dental College. Regular monitoring and training are required at all levels.

Healthcare waste generation and management practice in government health centers of Addis Ababa, Ethiopia.

PubMed

Tadesse, Menelik Legesse; Kumie, Abera

2014-11-25

Healthcare wastes are hazardous organic and inorganic wastes. The waste disposal management in Addis Ababa city is seen unscientific manner. The waste management practice in the health facilities are poor and need improvement. This study will help different organizations, stakeholders and policy makers to correct and improve the existing situation of healthcare waste legislation and enforcement and training of staff in the healthcare facilities in Addis Ababa. The study aimed to assess the existing generation and management practice of healthcare waste in selected government health centers of Addis Ababa. The cross-sectional study was conducted to quantify waste generation rate and evaluate its management system. The study area was Addis Ababa. The sample size was determined by simple random sampling technique, the sampling procedure involved 10 sub-cities of Addis Ababa. Data were collected using both waste collecting and measuring equipment and check list. The Data was entered by EPI INFO version 6.04d and analyzed by and SPSS for WINDOW version15. The mean (±SD) healthcare waste generation rate was 9.61 ± 3.28 kg/day of which (38%) 3.64 ± 1.45 kg/day was general or non-hazardous waste and (62%) 5.97 ± 2.31 kg/day was hazardous. The mean healthcare waste generation rate between health centers was a significant different with Kurskal-Wallis test (χ2 = 21.83, p-value = 0.009). All health centers used safety boxes for collection of sharp wastes and all health centers used plastic buckets without lid for collection and transportation of healthcare waste. Pre treatment of infectious wastes was not practiced by any of the health centers. All health centers used incinerators and had placenta pit for disposal of pathological waste however only seven out of ten pits had proper covering material. Segregation of wastes at point of generation with appropriate collection materials and pre- treatment of infectious waste before disposal should be practiced. Training should be given to healthcare workers and waste handlers. Incinerators must be constructed in a manner that facilitates complete combustion and the lining of placenta pit should be constructed in water tight material.

Environmental evaluation of municipal waste prevention

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gentil, Emmanuel C.; Gallo, Daniele; Christensen, Thomas H., E-mail: thho@env.dtu.dk

Highlights: > Influence of prevention on waste management systems, excluding avoided production, is relatively minor. > Influence of prevention on overall supply chain, including avoided production is very significant. > Higher relative benefits of prevention are observed in waste management systems relying mainly on landfills. - Abstract: Waste prevention has been addressed in the literature in terms of the social and behavioural aspects, but very little quantitative assessment exists of the environmental benefits. Our study evaluates the environmental consequences of waste prevention on waste management systems and on the wider society, using life-cycle thinking. The partial prevention of unsolicited mail,more » beverage packaging and food waste is tested for a 'High-tech' waste management system relying on high energy and material recovery and for a 'Low-tech' waste management system with less recycling and relying on landfilling. Prevention of 13% of the waste mass entering the waste management system generates a reduction of loads and savings in the waste management system for the different impacts categories; 45% net reduction for nutrient enrichment and 12% reduction for global warming potential. When expanding our system and including avoided production incurred by the prevention measures, large savings are observed (15-fold improvement for nutrient enrichment and 2-fold for global warming potential). Prevention of food waste has the highest environmental impact saving. Prevention generates relatively higher overall relative benefit for 'Low-tech' systems depending on landfilling. The paper provides clear evidence of the environmental benefits of waste prevention and has specific relevance in climate change mitigation.« less

Effective Strategies for Enhancing Waste Management at University Campuses

ERIC Educational Resources Information Center

Ebrahimi, Kianoosh; North, Leslie A.

2017-01-01

Purpose: The purpose of this study is to identify and assess the waste management strategies that should be priorities for higher education institutions. The role of policy instruments (i.e. purchasing policies and recycling initiatives) in implementing sustainable zero-waste management programs at higher education institutions was investigated…

A system dynamics-based environmental performance simulation of construction waste reduction management in China.

PubMed

Ding, Zhikun; Yi, Guizhen; Tam, Vivian W Y; Huang, Tengyue

2016-05-01

A huge amount of construction waste has been generated from increasingly higher number of construction activities than in the past, which has significant negative impacts on the environment if they are not properly managed. Therefore, effective construction waste management is of primary importance for future sustainable development. Based on the theory of planned behaviors, this paper develops a system dynamic model of construction waste reduction management at the construction phase to simulate the environmental benefits of construction waste reduction management. The application of the proposed model is shown using a case study in Shenzhen, China. Vensim is applied to simulate and analyze the model. The simulation results indicate that source reduction is an effective waste reduction measure which can reduce 27.05% of the total waste generation. Sorting behaviors are a premise for improving the construction waste recycling and reuse rates which account for 15.49% of the total waste generated. The environmental benefits of source reduction outweigh those of sorting behaviors. Therefore, to achieve better environmental performance of the construction waste reduction management, attention should be paid to source reduction such as low waste technologies and on-site management performance. In the meantime, sorting behaviors encouragement such as improving stakeholders' waste awareness, refining regulations, strengthening government supervision and controlling illegal dumping should be emphasized. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solid waste management challenges for cities in developing countries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abarca Guerrero, Lilliana, E-mail: l.abarca.guerrero@tue.nl; Maas, Ger, E-mail: g.j.maas@tue.nl; Hogland, William, E-mail: william.hogland@lnu.se

2013-01-15

Highlights: Black-Right-Pointing-Pointer Stakeholders. Black-Right-Pointing-Pointer Factors affecting performance waste management systems. Black-Right-Pointing-Pointer Questionnaire as Annex for waste management baseline assessment. - Abstract: Solid waste management is a challenge for the cities' authorities in developing countries mainly due to the increasing generation of waste, the burden posed on the municipal budget as a result of the high costs associated to its management, the lack of understanding over a diversity of factors that affect the different stages of waste management and linkages necessary to enable the entire handling system functioning. An analysis of literature on the work done and reported mainly in publicationsmore » from 2005 to 2011, related to waste management in developing countries, showed that few articles give quantitative information. The analysis was conducted in two of the major scientific journals, Waste Management Journal and Waste Management and Research. The objective of this research was to determine the stakeholders' action/behavior that have a role in the waste management process and to analyze influential factors on the system, in more than thirty urban areas in 22 developing countries in 4 continents. A combination of methods was used in this study in order to assess the stakeholders and the factors influencing the performance of waste management in the cities. Data was collected from scientific literature, existing data bases, observations made during visits to urban areas, structured interviews with relevant professionals, exercises provided to participants in workshops and a questionnaire applied to stakeholders. Descriptive and inferential statistic methods were used to draw conclusions. The outcomes of the research are a comprehensive list of stakeholders that are relevant in the waste management systems and a set of factors that reveal the most important causes for the systems' failure. The information provided is very useful when planning, changing or implementing waste management systems in cities.« less

An assessment of the current municipal solid waste management system in Lahore, Pakistan.

PubMed

Masood, Maryam; Barlow, Claire Y; Wilson, David C

2014-09-01

The current status of solid waste management in Lahore, a metropolitan city of Pakistan, is reviewed in this article using an existing approach, the UN-Habitat city profile. This involves a systematic quantitative and qualitative assessment of physical components and governance features of the current waste management system. A material flow diagram (MFD) is developed, which allows visualisation of the current waste management system with all related inputs and outputs. This study shows that in the current system, waste collection and transportation is the main focus, however the collection coverage is only about 68%. There is no controlled or even semi-controlled waste disposal facility in Lahore. There is no official recycling system in the city. It is estimated that currently ~27% of waste by weight is being recycled through the informal sector. Making use of the organic content of the waste, a composting facility is operative in the city, producing 47,230 tonnes year(-1) of organic compost. Lahore does not perform very well in governance features. Inclusivity of users and providers of the waste management system is low in the city, as not all stakeholders are consulted in the decision making processes. Waste management costs US$20 per tonne of waste, where the main focus is only on waste collection, and the current user fees are much lower than the actual costs. This study recommends that recycling should be promoted by increasing public awareness and integrating the informal sector to make the current system sustainable and financially viable. © The Author(s) 2014.

Call It Trash, Garbage or Refuse: Four Case Studies Illustrate Community Waste Management Options.

ERIC Educational Resources Information Center

Kazzi, John W.

1990-01-01

Describes four successful community programs dealing with waste management issues, developed with assistance from Keep America Beautiful System: litter prevention (Beatrice, Nebraska); composting yard waste (Centralia, Illinois); recycling (Lake Jackson, Texas); and waste-to-energy incineration (Gastonia, North Carolina). Notes related education…

Municipal solid waste management planning for Xiamen City, China: a stochastic fractional inventory-theory-based approach.

PubMed

Chen, Xiujuan; Huang, Guohe; Zhao, Shan; Cheng, Guanhui; Wu, Yinghui; Zhu, Hua

2017-11-01

In this study, a stochastic fractional inventory-theory-based waste management planning (SFIWP) model was developed and applied for supporting long-term planning of the municipal solid waste (MSW) management in Xiamen City, the special economic zone of Fujian Province, China. In the SFIWP model, the techniques of inventory model, stochastic linear fractional programming, and mixed-integer linear programming were integrated in a framework. Issues of waste inventory in MSW management system were solved, and the system efficiency was maximized through considering maximum net-diverted wastes under various constraint-violation risks. Decision alternatives for waste allocation and capacity expansion were also provided for MSW management planning in Xiamen. The obtained results showed that about 4.24 × 10 6  t of waste would be diverted from landfills when p i is 0.01, which accounted for 93% of waste in Xiamen City, and the waste diversion per unit of cost would be 26.327 × 10 3  t per $10 6 . The capacities of MSW management facilities including incinerators, composting facility, and landfills would be expanded due to increasing waste generation rate.

Situation analysis and issues in management of biomedical waste in select small health care facilities in a ward under Bruhat Bengaluru Mahanagara Palike, Bangalore, India.

PubMed

Chethana, Thirthahalli; Thapsey, Hemanth; Gautham, Melur Sukumar; Sreekantaiah, Pruthvish; Suryanarayana, Suradhenupura Puttajois

2014-04-01

Smaller health care facilities especially clinics though believed to generate lesser quantum/categories of medical waste, the number of clinics/small health care settings are considerable. The movement to manage biomedical waste in a safe and scientific manner has gathered momentum among the medium and large hospitals in Bangalore, but there has been a little understanding and focus on the smaller health care facilities/clinics in this aspect. It is important to gather evidence regarding the current situation of bio-medical waste (BMW) management and issues in smaller health care settings, so as to expand the safe management to all points of generation in Bangalore and will also help to plan relevant interventional strategies for the same. Hence an exploratory study was conducted to assess the current situation and issues in management of BMW among small health care facilities (sHCF). This cross sectional study was conducted in T. Dasarahalli (ward number 15) under Bruhat Bengaluru Mahanagar Palike (BBMP) of Bangalore. Data was collected from a convenient sample of 35 nursing homes (<50 beds) and clinics in December 2011. The results of this study indicate that 3 (20 %) of nursing homes had a Policy for Health Care Waste Management, though committees for Infection control and Hospital waste management were absent. Recording system like injury and waste management registers were non-existent. In our study the Common Bio-medical Waste Treatment Facility operator collected waste from 28 (80 %) of the sHCF. Segregation at the point of generation was present in 22 (62.9 %) of the sHCF. Segregation process was compliant as per BMW rules 1998 among 5 (16.1 %) of the sHCF. 18 sHCF workers were vaccinated with hepatitis B and tetanus. Deficiencies were observed in areas of containment, sharps management and disinfection. It was observed that though the quantum and category of waste generated was limited there exist deficiencies which warrant initiation of system development measures including capacity building.

Multi-objective reverse logistics model for integrated computer waste management.

PubMed

Ahluwalia, Poonam Khanijo; Nema, Arvind K

2006-12-01

This study aimed to address the issues involved in the planning and design of a computer waste management system in an integrated manner. A decision-support tool is presented for selecting an optimum configuration of computer waste management facilities (segregation, storage, treatment/processing, reuse/recycle and disposal) and allocation of waste to these facilities. The model is based on an integer linear programming method with the objectives of minimizing environmental risk as well as cost. The issue of uncertainty in the estimated waste quantities from multiple sources is addressed using the Monte Carlo simulation technique. An illustrated example of computer waste management in Delhi, India is presented to demonstrate the usefulness of the proposed model and to study tradeoffs between cost and risk. The results of the example problem show that it is possible to reduce the environmental risk significantly by a marginal increase in the available cost. The proposed model can serve as a powerful tool to address the environmental problems associated with exponentially growing quantities of computer waste which are presently being managed using rudimentary methods of reuse, recovery and disposal by various small-scale vendors.

Hospital waste management status in Iran: a case study in the teaching hospitals of Iran University of Medical Sciences.

PubMed

Farzadkia, Mahdi; Moradi, Arash; Mohammadi, Mojtaba Shah; Jorfi, Sahand

2009-06-01

Hospital waste materials pose a wide variety of health and safety hazards for patients and healthcare workers. Many of hospitals in Iran have neither a satisfactory waste disposal system nor a waste management and disposal policy. The main objective of this research was to investigate the solid waste management in the eight teaching hospitals of Iran University of Medical Sciences. In this cross-sectional study, the main stages of hospital waste management including generation, separation, collection, storage, and disposal of waste materials were assessed in these hospitals, located in Tehran city. The measurement was conducted through a questionnaire and direct observation by researchers. The data obtained was converted to a quantitative measure to evaluate the different management components. The results showed that the waste generation rate was 2.5 to 3.01 kg bed(-1) day(-1), which included 85 to 90% of domestic waste and 10 to 15% of infectious waste. The lack of separation between hazardous and non-hazardous waste, an absence of the necessary rules and regulations applying to the collection of waste from hospital wards and on-site transport to a temporary storage location, a lack of proper waste treatment, and disposal of hospital waste along with municipal garbage, were the main findings. In order to improve the existing conditions, some extensive research to assess the present situation in the hospitals of Iran, the compilation of rules and establishment of standards and effective training for the personnel are actions that are recommended.

Assessing knowledge, performance, and efficiency for hospital waste management-a comparison of government and private hospitals in Pakistan.

PubMed

Ali, Mustafa; Wang, Wenping; Chaudhry, Nawaz; Geng, Yong; Ashraf, Uzma

2017-04-01

Proper management of healthcare waste is a critical concern in many countries of the world. Rapid urbanization and population growth rates pose serious challenges to healthcare waste management infrastructure in such countries. This study was aimed at assessing the situation of hospital waste management in a major city of Pakistan. Simple random sampling was used to select 12 government and private hospitals in the city. Field visits, physical measurements, and questionnaire survey method were used for data collection. Information was obtained regarding hospital waste generation, segregation, collection, storage, transportation, and disposal. Data envelopment analysis (DEA) was used to classify the hospitals on the basis of their relative waste management efficiencies. The weighted average total waste generation at the surveyed hospitals was discovered to be 1.53 kg/patient/day of which 75.15% consisted of general waste and the remaining consisted of biomedical waste. Of the total waste, 24.54% came from the public hospital and the remaining came from the private hospitals. DEA showed that seven of the surveyed hospitals had scale or pure technical inefficiencies in their waste management activities. The public hospital was relatively less efficient than most of the private hospitals in these activities. Results of the questionnaire survey showed that none of the surveyed hospitals was carrying out waste management in strict compliance with government regulations. Moreover, hospital staff at all the surveyed hospitals had low level of knowledge regarding safe hospital waste management practices. The current situation should be rectified in order to avoid environmental and epidemiological risks.

Assessment of public perception of radioactive waste management in Korea.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trone, Janis R.; Cho, SeongKyung; Whang, Jooho

2011-11-01

The essential characteristics of the issue of radioactive waste management can be conceptualized as complex, with a variety of facets and uncertainty. These characteristics tend to cause people to perceive the issue of radioactive waste management as a 'risk'. This study was initiated in response to a desire to understand the perceptions of risk that the Korean public holds towards radioactive waste and the relevant policies and policy-making processes. The study further attempts to identify the factors influencing risk perceptions and the relationships between risk perception and social acceptance.

Improving integrated waste management at the regional level: the case of Lombardia.

PubMed

Rigamonti, Lucia; Falbo, Alida; Grosso, Mario

2013-09-01

The article summarises the main results of the 'Gestione Rifiuti in Lombardia: Analisi del ciclo di vita' (Waste management in Lombardia region: Life cycle assessment; GERLA) project. Life cycle assessment (LCA) has been selected by Regione Lombardia as a strategic decision support tool in the drafting of its new waste management programme. The goal was to use the life cycle thinking approach to assess the current regional situation and thus to give useful strategic indications for the future waste management. The first phase of the study consisted of the LCA of the current management of municipal waste in the Lombardia region (reference year: 2009). The interpretation of such results has allowed the definition of four possible waste management scenarios for the year 2020, with the final goal being to improve the environmental performance of the regional system. The results showed that the current integrated waste management of Lombardia region is already characterised by good energy and environmental performances. However, there is still room for further improvement: actions based, on the one hand, on a further increase in recycling rates and, on the other hand, on a series of technological modifications, especially in food waste and residual waste management, can be undertaken to improve the overall system.

Reverse logistics network for municipal solid waste management: The inclusion of waste pickers as a Brazilian legal requirement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferri, Giovane Lopes, E-mail: giovane.ferri@aluno.ufes.br; Diniz Chaves, Gisele de Lorena, E-mail: gisele.chaves@ufes.br; Ribeiro, Glaydston Mattos, E-mail: glaydston@pet.coppe.ufrj.br

Highlights: • We propose a reverse logistics network for MSW involving waste pickers. • A generic facility location mathematical model was validated in a Brazilian city. • The results enable to predict the capacity for screening and storage centres (SSC). • We minimise the costs for transporting MSW with screening and storage centres. • The use of SSC can be a potential source of revenue and a better use of MSW. - Abstract: This study proposes a reverse logistics network involved in the management of municipal solid waste (MSW) to solve the challenge of economically managing these wastes considering themore » recent legal requirements of the Brazilian Waste Management Policy. The feasibility of the allocation of MSW material recovery facilities (MRF) as intermediate points between the generators of these wastes and the options for reuse and disposal was evaluated, as well as the participation of associations and cooperatives of waste pickers. This network was mathematically modelled and validated through a scenario analysis of the municipality of São Mateus, which makes the location model more complete and applicable in practice. The mathematical model allows the determination of the number of facilities required for the reverse logistics network, their location, capacities, and product flows between these facilities. The fixed costs of installation and operation of the proposed MRF were balanced with the reduction of transport costs, allowing the inclusion of waste pickers to the reverse logistics network. The main contribution of this study lies in the proposition of a reverse logistics network for MSW simultaneously involving legal, environmental, economic and social criteria, which is a very complex goal. This study can guide practices in other countries that have realities similar to those in Brazil of accelerated urbanisation without adequate planning for solid waste management, added to the strong presence of waste pickers that, through the characteristic of social vulnerability, must be included in the system. In addition to the theoretical contribution to the reverse logistics network problem, this study aids in decision-making for public managers who have limited technical and administrative capacities for the management of solid wastes.« less

Knowledge, Attitude and Practice of Healthcare Managers to Medical Waste Management and Occupational Safety Practices: Findings from Southeast Nigeria.

PubMed

Anozie, Okechukwu Bonaventure; Lawani, Lucky Osaheni; Eze, Justus Ndulue; Mamah, Emmanuel Johnbosco; Onoh, Robinson Chukwudi; Ogah, Emeka Onwe; Umezurike, Daniel Akuma; Anozie, Rita Onyinyechi

2017-03-01

Awareness of appropriate waste management procedures and occupational safety measures is fundamental to achieving a safe work environment, and ensuring patient and staff safety. This study was conducted to assess the attitude of healthcare managers to medical waste management and occupational safety practices. This was a cross-sectional study conducted among 54 hospital administrators in Ebonyi state. Semi-structured questionnaires were used for qualitative data collection and analyzed with SPSS statistics for windows (2011), version 20.0 statistical software (Armonk, NY: IBM Corp). Two-fifth (40%) of healthcare managers had received training on medical waste management and occupational safety. Standard operating procedure of waste disposal was practiced by only one hospital (1.9%), while 98.1% (53/54) practiced indiscriminate waste disposal. Injection safety boxes were widely available in all health facilities, nevertheless, the use of incinerators and waste treatment was practiced by 1.9% (1/54) facility. However, 40.7% (22/54) and 59.3% (32/54) of respondents trained their staff and organize safety orientation courses respectively. Staff insurance cover was offered by just one hospital (1.9%), while none of the hospitals had compensation package for occupational hazard victims. Over half (55.6%; 30/54) of the respondents provided both personal protective equipment and post exposure prophylaxis for HIV. There was high level of non-compliance to standard medical waste management procedures, and lack of training on occupational safety measures. Relevant regulating agencies should step up efforts at monitoring and regulation of healthcare activities and ensure staff training on safe handling and disposal of hospital waste.

Possible global environmental impacts of solid waste practices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, M.M.; Holter, G.M.; DeForest, T.J.

1994-09-01

Pollutants resulting from the management of solid waste have been shown to affect the air, land, oceans, and waterways. In addition, solid wastes have other, more indirect impacts such as reduction in feedstocks of natural resources, because useful materials are disposed of rather than recycled. The objective of this study is to evaluate solid waste management practices that have negative implications on the global environment and develop recommendations for reducing such impacts. Recommendations identifying needed changes are identified that will reduce global impacts of solid waste practices in the future. The scope of this study includes the range of non-hazardousmore » solid wastes produced within our society, including municipal solid waste (MSW) and industrial solid waste (ISW), as well as industry-specific wastes from activities such as construction, demolition, and landclearing. Most solid waste management decisions continue to be made and implemented at very local levels, predominantly with a short-term focus to respond to relatively immediate pressures of landfill shortages, funding problems, political considerations, and the like. In this rush to address immediate local problems, little consideration is being given to potential impacts, either short- or long-term, at the national or global level resulting from solid waste management practices. More and more, the cumulative impacts from local decisions concerning solid waste management are beginning to manifest themselves in broader, longer-term impacts than are being addressed by the decision-makers or, at the very least, are presenting a greater and greater potential for such impacts.« less

A review and framework for understanding the potential impact of poor solid waste management on health in developing countries.

PubMed

Ziraba, Abdhalah K; Haregu, Tilahun Nigatu; Mberu, Blessing

2016-01-01

The increase in solid waste generated per capita in Africa has not been accompanied by a commensurate growth in the capacity and funding to manage it. It is reported that less than 30% of urban waste in developing countries is collected and disposed appropriately. The implications of poorly managed waste on health are numerous and depend on the nature of the waste, individuals exposed, duration of exposure and availability of interventions for those exposed. To present a framework for understanding the linkages between poor solid waste management, exposure and associated adverse health outcomes. The framework will aid understanding of the relationships, interlinkages and identification of the potential points for intervention. Development of the framework was informed by a review of literature on solid waste management policies, practices and its impact on health in developing countries. A configurative synthesis of literature was applied to develop the framework. Several iterations of the framework were reviewed by experts in the field. Each linkage and outcomes are described in detail as outputs of this study. The resulting framework identifies groups of people at a heightened risk of exposure and the potential health consequences. Using the iceberg metaphor, the framework illustrates the pathways and potential burden of ill-health related to solid waste that is hidden but rapidly unfolding with our inaction. The existing evidence on the linkage between poor solid waste management and adverse health outcomes calls to action by all stakeholders in understanding, prioritizing, and addressing the issue of solid waste in our midst to ensure that our environment and health are preserved. A resulting framework developed in this study presents a clearer picture of the linkages between poor solid waste management and could guide research, policy and action.

[Biomedical waste management in five hospitals in Dakar, Senegal].

PubMed

Ndiaye, M; El Metghari, L; Soumah, M M; Sow, M L

2012-10-01

Biomedical waste is currently a real health and environmental concern. In this regard, a study was conducted in 5 hospitals in Dakar to review their management of biomedical waste and to formulate recommendations. This is a descriptive cross-sectional study conducted from 1 April to 31 July 2010 in five major hospitals of Dakar. A questionnaire administered to hospital managers, heads of departments, residents and heads of hospital hygiene departments as well as interviews conducted with healthcare personnel and operators of waste incinerators made it possible to assess mechanisms and knowledge on biomedical waste management. Content analysis of interviews, observations and a data sheet allowed processing the data thus gathered. Of the 150 questionnaires distributed, 98 responses were obtained representing a response rate of 65.3%. An interview was conducted with 75 employees directly involved in the management of biomedical waste and observations were made on biomedical waste management in 86 hospital services. Sharps as well as blood and liquid waste were found in all services except in pharmacies, pharmaceutical waste in 66 services, infectious waste in 49 services and anatomical waste in 11 services. Sorting of biomedical waste was ill-adapted in 53.5% (N = 46) of services and the use of the colour-coding system effective in 31.4% (N = 27) of services. Containers for the safe disposal of sharps were available in 82.5% (N = 71) of services and were effectively utilized in 51.1% (N = 44) of these services. In most services, an illadapted packaging was observed with the use of plastic bottles and bins for waste collection and overfilled containers. With the exception of Hôpital Principal, the main storage area was in open air, unsecured, with biomedical waste littered on the floor and often mixed with waste similar to household refuse. The transfer of biomedical waste to the main storage area was done using trolleys or carts in 67.4% (N = 58) of services and wheelbarrows in 33.7% (N = 29). Biomedical waste was disposed of in old incinerators or in artisanal ovens with a great deal of smoke emanating from these. Working conditions were deemed poor by 81.3% (N = 61) of employees interviewed and personal protection equipment was available in 45.3% (N = 39) of services. Knowledge about biomedical waste management was deemed satisfactory by 62.6% (N = 47) of interviewees and 80% (N = 60) were aware of the health risks related to biomedical waste. The poor management of biomedical waste is a reality in hospital facilities in Dakar. This can be addressed by increasing the awareness of managers for an effective application of the legislation, implementing realistic management programmes and providing the appropriate on-the-job training to staff members.

Awareness about biomedical waste management and knowledge of effective recycling of dental materials among dental students

PubMed Central

Ranjan, Rajeev; Pathak, Ruchi; Singh, Dhirendra K.; Jalaluddin, Md.; Kore, Shobha A.; Kore, Abhijeet R.

2016-01-01

Aims and Objectives: Biomedical waste management has become a concern with increasing number of dental practitioners in India. Being health care professionals, dentists should be aware regarding safe disposal of biomedical waste and recycling of dental materials to minimize biohazards to the environment. The aim of the present study was to assess awareness regarding biomedical waste management as well as knowledge of effective recycling and reuse of dental materials among dental students. Materials and Methods: This cross-sectional study was conducted among dental students belonging from all dental colleges of Bhubaneswar, Odisha (India) from February 2016 to April 2016. A total of 500 students (208 males and 292 females) participated in the study, which was conducted in two phases. A questionnaire was distributed to assess the awareness of biomedical waste management and knowledge of effective recycling of dental materials, and collected data was examined on a 5-point unipolar scale in percentages to assess the relative awareness regarding these two different categorizes. The Statistical Package for Social Sciences was used to analyzed collected data. Results: Forty-four percent of the dental students were not at all aware about the management of biomedical waste, 22% were moderately aware, 21% slightly aware, 7% very aware, and 5% fell in extremely aware category. Similarly, a higher percentage of participants (61%) were completely unaware regarding recycling and reusing of biomedical waste. Conclusion: There is lack of sufficient knowledge among dental students regarding management of biomedical waste and recycling or reusing of dental materials. Considering its impact on the environment, biomedical waste management requires immediate academic assessment to increase the awareness during training courses. PMID:27891315

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alagoez, Aylin Zeren; Kocasoy, Guenay

Health-care waste management has been a significant problem in most economically developing countries as it is in Turkey. Most of the time, the main reason for the mismanagement of these wastes is the lack of appropriate legislation and effective control; other reasons are: financial strains and a lack of awareness. Being aware of the significance of the subject, in this paper the management of the health-care wastes in Istanbul, as a Metropolitan City of Turkey, was analyzed to create an integrated health-care waste management system in the city. Within the scope of the study, the existing situation and management practicesmore » such as the amount of the health-care wastes generated, segregation procedures, collection, temporary storage and transportation of the wastes within and outside of the institution were examined. Deficiencies, inconsistencies and improper applications were revealed. The existing Turkish Medical Wastes Control Regulation and institutional structure of the health-care waste management body were reviewed. After the evaluation and comparison with the requirements of other national and international organizations, items to be changed/added in the Regulation were identified. At the end of the study, the best management methods for the Istanbul City were determined and started to be applied at the institutions. After this study, the existing Regulation has been changed. The modified Regulation was published in 2005 and implementation has started. It is expected that by the application and implementation of the research outcomes, the management of health-care wastes in Istanbul and then in all over Turkey will be improved. The results obtained can also be used in most economically developing countries where there are similar environmental problems and strict budgets.« less

The role of non-governmental organizations in residential solid waste management: a case study of Puducherry, a coastal city of India.

PubMed

Rajamanikam, Ramamoorthy; Poyyamoli, Gopalsamy; Kumar, Sunil; R, Lekshmi

2014-09-01

Poorly planned and uncontrolled urbanization in India has caused a variety of negative, often irreversible, environmental impacts. The impacts appear to be unavoidable and not easily mitigable due to the mounting public health problems caused by non-segregation of solid wastes at source and their subsequent improper management. Recently in India, non-governmental organizations (NGOs) and other civil society organizations have increasingly started to get involved in improving waste management services. Municipal solid waste management being a governmental function, the contribution of NGOs in this field has not been well documented. This study highlights the activities and services of Shuddham, an NGO functioning in the town of Puducherry within the Union Territory of Puducherry in South India. The NGO program promoted much needed awareness and education, encouraged source separation, enhanced door-to-door collection, utilized wastes as raw materials and generated more job opportunities. Even though source separation prior to door-to-door collection is a relatively new concept, a significant percentage of residents (39%) in the study area participated fully, while a further 48% participated in the collection service. The average amount of municipal solid waste generated by residential units in the Raj Bhavan ward was 8582 kg/month of which 47% was recovered through active recycling and composting practices. The study describes the features and performance of NGO-mediated solid waste management, and evaluates the strengths and weaknesses as well as the opportunities and threats of this system to see whether this model can sustainably replace the low-performance conventional solid waste management in practice in the town of Puducherry. The experiences from this case study are expected to provide broad guidelines to better understand the role of NGOs and their contributions towards sustainable waste management practices in urban areas. © The Author(s) 2014.

Dental solid waste characterization and management in Iran: a case study of Sistan and Baluchestan Province.

PubMed

Bazrafshan, Edris; Mohammadi, Leili; Mostafapour, Ferdos Kord; Moghaddam, Alireza Ansari

2014-02-01

The management of dental solid waste continues to be a major challenge, particularly in most healthcare facilities of the developing world. In Iran, few studies on management of dental solid waste and its composition are available. An effort has been made through this study to evaluate the hazardous and infectious status of dental solid waste, keeping in mind its possible role in cross-infection chain. For this study, 123 private dental centres and 36 public dental centres were selected and the composition and generation rate of dental solid waste produced were measured. Dental solid waste was classified to four main categories: (i) domestic-type; (ii) potentially infectious; (iii) chemical and pharmaceutical; and (iv) toxic, which constituted 11.7, 80.3, 6.3, and 1.7%, respectively, of the total. Also, the results indicated that the dental solid waste per patient per day generation rate for total, domestic-type, potentially infectious, chemical and pharmaceutical, and toxic wastes were 169.9, 8.6, 153.3, 11.2, and 3.3 g/patient/d, respectively. Furthermore, the per day generation rates for total, domestic-type, potentially infectious, chemical and pharmaceutical, and toxic wastes were 194.5, 22.6, 156.1, 12.3, and 3.4 kg/d, respectively. According to findings of this study, for best management of dental waste it is suggested that source reduction, separation, reuse, and recycling programmes be implemented and each section of dental waste be collected and disposed of separately and in accordance with related criteria.

Effects of an incinerator project on a healthcare-waste management system.

PubMed

Khammaneechan, Patthanasak; Okanurak, Kamolnetr; Sithisarankul, Pornchai; Tantrakarnapa, Kraichat; Norramit, Poonsup

2011-10-01

This evaluative research study aimed to assess the effects of the central healthcare incinerator project on waste management in Yala Province. The study data were collected twice: at baseline and during the operational phase. A combination of structured interview and observation were used during data collection. The study covered 127 healthcare facilities: government hospitals, healthcare centres, and private clinics. The results showed 63% of healthcare risk waste (HCRW) handlers attended the HCRW management training. Improvements in each stage of the HCRW management system were observed in all groups of facilities. The total cost of the HCRW management system did not change, however; the costs for hospitals decreased, whereas those for clinics increased significantly. It was concluded that the central healthcare waste incinerator project positively affected HCRW management in the area, although the costs of management might increase for a particular group. However, the benefits of changing to a more appropriately managed HCRW system will outweigh the increased costs.

Hospital waste management in El-Beheira Governorate, Egypt.

PubMed

Abd El-Salam, Magda Magdy

2010-01-01

This study investigated the hospital waste management practices used by eight randomly selected hospitals located in Damanhour City of El-Beheira Governorate and determined the total daily generation rate of their wastes. Physico-chemical characteristics of hospital wastes were determined according to standard methods. A survey was conducted using a questionnaire to collect information about the practices related to waste segregation, collection procedures, the type of temporary storage containers, on-site transport and central storage area, treatment of wastes, off-site transport, and final disposal options. This study indicated that the quantity of medical waste generated by these hospitals was 1.249tons/day. Almost two-thirds was waste similar to domestic waste. The remainder (38.9%) was considered to be hazardous waste. The survey results showed that segregation of all wastes was not conducted according to consistent rules and standards where some quantity of medical waste was disposed of with domestic wastes. The most frequently used treatment method for solid medical waste was incineration which is not accepted at the current time due to the risks associated with it. Only one of the hospitals was equipped with an incinerator which is devoid of any air pollution control system. Autoclaving was also used in only one of the selected hospitals. As for the liquid medical waste, the survey results indicated that nearly all of the surveyed hospitals were discharging it in the municipal sewerage system without any treatment. It was concluded that the inadequacies in the current hospital waste management practices in Damanhour City were mainly related to ineffective segregation at the source, inappropriate collection methods, unsafe storage of waste, insufficient financial and human resources for proper management, and poor control of waste disposal. The other issues that need to be considered are a lack of appropriate protective equipment and lack of training and clear lines of responsibilities between the departments involved in hospital waste management. Effective medical waste management programs are multisectoral and require cooperation between all levels of implementation, from national and local governments to hospital staff and private businesses. 2009 Elsevier Ltd. All rights reserved.

Greenhouse gas emissions from solid waste in Beijing: The rising trend and the mitigation effects by management improvements.

PubMed

Yu, Yongqiang; Zhang, Wen

2016-04-01

Disposal of solid waste poses great challenges to city managements. Changes in solid waste composition and disposal methods, along with urbanisation, can certainly affect greenhouse gas emissions from municipal solid waste. In this study, we analysed the changes in the generation, composition and management of municipal solid waste in Beijing. The changes of greenhouse gas emissions from municipal solid waste management were thereafter calculated. The impacts of municipal solid waste management improvements on greenhouse gas emissions and the mitigation effects of treatment techniques of greenhouse gas were also analysed. Municipal solid waste generation in Beijing has increased, and food waste has constituted the most substantial component of municipal solid waste over the past decade. Since the first half of 1950s, greenhouse gas emission has increased from 6 CO2-eq Gg y(-1)to approximately 200 CO2-eq Gg y(-1)in the early 1990s and 2145 CO2-eq Gg y(-1)in 2013. Landfill gas flaring, landfill gas utilisation and energy recovery in incineration are three techniques of the after-emission treatments in municipal solid waste management. The scenario analysis showed that three techniques might reduce greenhouse gas emissions by 22.7%, 4.5% and 9.8%, respectively. In the future, if waste disposal can achieve a ratio of 4:3:3 by landfill, composting and incineration with the proposed after-emission treatments, as stipulated by the Beijing Municipal Waste Management Act, greenhouse gas emissions from municipal solid waste will decrease by 41%. © The Author(s) 2016.

Waste electrical and electronic equipment management and Basel Convention compliance in Brazil, Russia, India, China and South Africa (BRICS) nations.

PubMed

Ghosh, Sadhan Kumar; Debnath, Biswajit; Baidya, Rahul; De, Debashree; Li, Jinhui; Ghosh, Sannidhya Kumar; Zheng, Lixia; Awasthi, Abhishek Kumar; Liubarskaia, Maria A; Ogola, Jason S; Tavares, André Neiva

2016-08-01

Brazil, Russia, India, China and South Africa (BRICS) nations account for one-quarter of the world's land area, having more than 40% of the world's population, and only one-quarter of the world gross national income. Hence the study and review of waste electrical and electronic equipment management systems in BRICS nations is of relevance. It has been observed from the literature that there are studies available comparing two or three country's waste electrical and electronic equipment status, while the study encompassing the BRICS nations considering in a single framework is scant. The purpose of this study is to analyse the existing waste electrical and electronic equipment management systems and status of compliance to Basel convention in the BRICS nations, noting possible lessons from matured systems, such as those in the European Union EU) and USA. The study introduced a novel framework for a waste electrical and electronic equipment management system that may be adopted in BRICS nations and revealed that BRICS countries have many similar types of challenges. The study also identified some significant gaps with respect to the management systems and trans-boundary movement of waste electrical and electronic equipment, which may attract researchers for further research. © The Author(s) 2016.

Safe injections and waste management among healthcare workers at a regional hospital in northern Tanzania.

PubMed

Nilsson, Josefine; Pembe, Andrea B; Urasa, Miriam; Darj, Elisabeth

2013-01-01

Unsafe injections and substandard waste management are public health issues exposing healthcare workers and the community to the risk of infections. The objective of this study was to assess the knowledge and practice of safe injections and health care waste management among healthcare workers at a regional hospital in northern Tanzania. This cross sectional descriptive study was conducted in a regional hospital in northern Tanzania. Data was collected through a self-administered questionnaire with additional observations of the incinerator, injections, waste practices, and the availability of medical supplies. Data was analysed in SPSS descriptive statistics and chi-square tests were performed. A total of 223 of 305 (73%) healthcare workers from different cadres were included in the study. The majority of healthcare workers had adequate knowledge and practice of safe injections, but inadequate knowledge about waste management. The majority of the staff reported knowledge of HIV as a risk factor, however, had less knowledge about other blood-borne infections. Guidelines and posters on post exposure prophylaxes and waste management -were present at the hospital, however, the incinerator had no fence or temperature gauge. In conclusion, healthcare workers reported good knowledge and practice of injections, and high knowledge of HIV transmission routes. However, the hospital is in need of a well functioning incinerator and healthcare workers require sufficient medical supplies. There was a need for continual training about health care waste management and avoidance of blood-borne pathogens that may be transmitted through unsafe injections or poor health care waste management.

Risk Reduction from Minimization of Persistent, Bioaccumulative, and Toxic Waste Materials Within the U.S. Industrial Solid Waste Management System

EPA Science Inventory

This study addressed three questions of interest in national-scale solid and hazardous waste management decision-making within the United States: 1) can we quantify the reduction in risk to human and ecological receptors resulting from the reduction of certain industrial waste s...

Solid Waste Management in Recreational Forest Areas.

ERIC Educational Resources Information Center

Spooner, Charles S.

The Forest Service, U. S. Department of Agriculture, requested the Bureau of Solid Waste Management to conduct a study of National Forest recreation areas to establish waste generation rates for major recreation activities and to determine the cost of solid waste handling for selected Forest Service Districts. This report describes the 1968 solid…

Public Health Risks from Mismanagement of Healthcare Wastes in Shinyanga Municipality Health Facilities, Tanzania

PubMed Central

Kuchibanda, Kizito; Mayo, Aloyce W.

2015-01-01

The increase of healthcare facilities in Shinyanga municipality has resulted in an increase of healthcare wastes, which poses serious threats to the environment, health workers, and the general public. This research was conducted to investigate management practices of healthcare wastes in Shinyanga municipality with a view of assessing health risks to health workers and the general public. The study, which was carried out in three hospitals, involved the use of questionnaires, in-depth interview, and observation checklist. The results revealed that healthcare wastes are not quantified or segregated in all the three hospitals. Healthcare wastes at the Shinyanga Regional Referral Hospital are disposed of by on-site incineration and burning and some wastes are disposed off-site. At Kolandoto DDH only on-site burning and land disposal are practiced, while at Kambarage UHC healthcare solid wastes are incinerated, disposed of on land disposal, and burned. Waste management workers do not have formal training in waste management techniques and the hospital administrations pay very little attention to appropriate management of healthcare wastes. In light of this, it is evident that management of healthcare solid wastes is not practiced in accordance with the national and WHO's recommended standards. PMID:26779565

Use of theoretical waste inventories in planning and monitoring of hazardous waste management systems.

PubMed

Yilmaz, Ozge; Can, Zehra S; Toroz, Ismail; Dogan, Ozgur; Oncel, Salim; Alp, Emre; Dilek, Filiz B; Karanfil, Tanju; Yetis, Ulku

2014-08-01

Hazardous waste (HW) generation information is an absolute necessity for ensuring the proper planning, implementation, and monitoring of any waste management system. Unfortunately, environmental agencies in developing countries face difficulties in gathering data directly from the creators of such wastes. It is possible, however, to construct theoretical HW inventories using the waste generation factors (WGFs). The objective of this study was to develop a complete nationwide HW inventory of Turkey that relies on nation-specific WGFs to support management activities of the Turkish Ministry of Environment and Urbanization (MoEU). Inventory studies relied on WGFs from: (a) the literature and (b) field studies and analysis of waste declarations reflecting country-specific industrial practices. Moreover, new tools were introduced to the monitoring infrastructure of MoEU to obtain a comprehensive waste generation data set. Through field studies and a consideration of country specific conditions, it was possible to more thoroughly elucidate HW generation trends in Turkey, a method that was deemed superior to other alternatives. Declaration and literature based WGFs also proved most helpful in supplementing field observations that could not always be conducted. It was determined that these theoretical inventories could become valuable assets in supporting regulating agencies in developing countries for a more thorough implementation of HW management systems. © The Author(s) 2014.

A dynamic model for assessing the effects of management strategies on the reduction of construction and demolition waste.

PubMed

Yuan, Hongping; Chini, Abdol R; Lu, Yujie; Shen, Liyin

2012-03-01

During the past few decades, construction and demolition (C&D) waste has received increasing attention from construction practitioners and researchers worldwide. A plethora of research regarding C&D waste management has been published in various academic journals. However, it has been determined that existing studies with respect to C&D waste reduction are mainly carried out from a static perspective, without considering the dynamic and interdependent nature of the whole waste reduction system. This might lead to misunderstanding about the actual effect of implementing any waste reduction strategies. Therefore, this research proposes a model that can serve as a decision support tool for projecting C&D waste reduction in line with the waste management situation of a given construction project, and more importantly, as a platform for simulating effects of various management strategies on C&D waste reduction. The research is conducted using system dynamics methodology, which is a systematic approach that deals with the complexity - interrelationships and dynamics - of any social, economic and managerial system. The dynamic model integrates major variables that affect C&D waste reduction. In this paper, seven causal loop diagrams that can deepen understanding about the feedback relationships underlying C&D waste reduction system are firstly presented. Then a stock-flow diagram is formulated by using software for system dynamics modeling. Finally, a case study is used to illustrate the validation and application of the proposed model. Results of the case study not only built confidence in the model so that it can be used for quantitative analysis, but also assessed and compared the effect of three designed policy scenarios on C&D waste reduction. One major contribution of this study is the development of a dynamic model for evaluating C&D waste reduction strategies under various scenarios, so that best management strategies could be identified before being implemented in practice. Copyright © 2011 Elsevier Ltd. All rights reserved.

Evaluation of municipal solid waste management in egyptian rural areas.

PubMed

El-Messery, Mamdouh A; Ismail, Gaber A; Arafa, Anwaar K

2009-01-01

A two years study was conducted to evaluate the solid waste management system in 143 villages representing the Egyptian rural areas. The study covers the legal responsibilities, service availability, environmental impacts, service providers, financial resources, private sector participation and the quality of collection services. According to UN reports more than 55% of Egyptian population lives in rural areas. A drastic change in the consumption pattern altered the quantity and quality of the generated solid wastes from these areas. Poor solid waste management systems are stigmata in most of the Egyptian rural areas. This causes several environmental and health problems. It has been found that solid waste collection services cover only 27% of the surveyed villages, while, the statistics show that 75% of the surveyed villages are formally covered. The service providers are local villager units, private contractors and civil community associations with a percentage share 71%, 24% and 5% respectively. The operated services among these sectors were 25%, 71% and 100% respectively. The share of private sector in solid waste management in rural areas is still very limited as a result of the poverty of these communities and the lack of recyclable materials in their solid waste. It has been found that direct throwing of solid waste on the banks of drains and canals as well as open dumping and uncontrolled burning of solid waste are the common practice in most of the Egyptian rural areas. The available land for landfill is not enough, pitiable designed, defectively constructed and unreliably operated. Although solid waste generated in rural areas has high organic contents, no composting plant was installed. Shortage in financial resources allocated for valorization of solid waste management in the Egyptian rural areas and lower collection fees are the main points of weakness which resulted in poor solid waste management systems. On the other hand, the farmer's participation in solid waste management through the composting of organic matter and using of food waste as an animal feed are considered strength points. However, throwing of solid waste on the banks of water streams, open dumping and uncontrolled burning of solid waste are environmental damaging behaviors that need to be changed. Integrated solid waste management in the Egyptian rural areas is not yet among the priorities of the Egyptian government.

Improving waste segregation while reducing costs in a tertiary-care hospital in a lower-middle-income country in Central America.

PubMed

Johnson, Kyle M; González, Miriam L; Dueñas, Lourdes; Gamero, Mario; Relyea, George; Luque, Laura E; Caniza, Miguela A

2013-07-01

Healthcare waste (HCW) management and segregation are essential to ensure safety, environmental protection and cost control. Poor HCW management increase risks and costs for healthcare institutions. On-going surveillance and training are important to maintain good HCW practices. Our objectives were to evaluate and improve HCW practices at Hospital Bloom, San Salvador, El Salvador. We studied HCW disposal practices by observing waste containers, re-segregating waste placed in biohazardous waste bags, and administering a seven-itemsknowledge survey before and after training in waste management at Hospital Bloom. The training was based on national and international standards. We followed total biohazardous waste production before and after the training. The hospital staff was knowledgeable about waste segregation practices, but had poor compliance with national policies. Re-segregating waste in biohazardous waste bags showed that 61% of this waste was common waste, suggesting that the staff was possibly unaware of the cost of mis-segregating healthcare waste. After staff training in HCW management, the correct responses increased by 44% and biohazardous waste disposal at the hospital reduced by 48%. Better segregation of biohazardous waste and important savings can be obtained by HCW management education of hospital staff. Hospitals can benefit from maximising the use of available resources by sustaining best practices of HCW, especially those in hospitals in lower-middle-income countries.

Solid waste prevention and management at green festivals: A case study of the Andanças Festival, Portugal.

PubMed

Martinho, Graça; Gomes, Ana; Ramos, Mário; Santos, Pedro; Gonçalves, Graça; Fonseca, Miguel; Pires, Ana

2018-01-01

Research on waste prevention and management at green festivals is scarce. The present study helps to fill this gap by analyzing waste prevention/reduction and management measures implemented at the Andanças festival, Portugal. Waste characterization campaigns and a questionnaire survey were conducted during the festival. The results show that the largest amount of waste generated was residual waste, followed by food and kitchen waste and packaging waste. The amount of waste generated per person per day at the festival was lower than that of other festivals for both the entire venue and the canteen. Concerning food and kitchen waste generated at the canteen, the amounts are in accordance with the findings of previous studies, but the amount of the edible fraction is comparatively low. Source separation rates are high, in line with other festivals that engage in food-waste source separation. Factors affecting the participation of attendees in waste prevention measures at the festival are the type of participant, their region of origin, the frequency of visits, and whether they are attending as a family. Efforts must be made to increase the awareness of attendees about waste prevention measures, to develop guidelines and methods to quantify the waste prevention measures, and to formulate policies aimed at increasing the application of the zero-waste principle at festivals. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of a food waste disposer policy on solid waste and wastewater management with economic implications of environmental externalities.

PubMed

Maalouf, Amani; El-Fadel, Mutasem

2017-11-01

In this study, the carbon footprint of introducing a food waste disposer (FWD) policy was examined in the context of its implications on solid waste and wastewater management with economic assessment of environmental externalities emphasizing potential carbon credit and increased sludge generation. For this purpose, a model adopting a life cycle inventory approach was developed to integrate solid waste and wastewater management processes under a single framework and test scenarios for a waste with high organic food content typical of developing economies. For such a waste composition, the results show that a FWD policy can reduce emissions by nearly ∼42% depending on market penetration, fraction of food waste ground, as well as solid waste and wastewater management schemes, including potential energy recovery. In comparison to baseline, equivalent economic gains can reach ∼28% when environmental externalities including sludge management and emissions variations are considered. The sensitivity analyses on processes with a wide range in costs showed an equivalent economic impact thus emphasizing the viability of a FWD policy although the variation in the cost of sludge management exhibited a significant impact on savings. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analysis of the healthcare waste management status in Tehran hospitals.

PubMed

Malekahmadi, Fariba; Yunesian, Masud; Yaghmaeian, Kamyar; Nadafi, Kazem

2014-01-01

Considering the importance of healthcare waste management, following the ratification of the Waste Management law in 2005 and the subsequent approval of its executive bylaw in 2006 and finally the healthcare waste management criteria passing by the parliament in 2008, a review on the status of healthcare waste management is needed to implement the mentioned law properly. In this retrospective study during six months period all public hospitals in Iran's capital city, Tehran, were selected to conduct the survey. Data collected through an expert-standardized questionnaire was analyzed by using SPSS software. The results of the current status of healthcare waste management in Tehran hospitals showed 5.6% of hospitals were ranked excellent, 50.7% good, 26.4% medium, and the 13.9% of hospitals were ranked weak and 3.5% ranked very poor. The findings showed that appropriate technologies should be used to have better disposal stage. As the ratified criteria were not fully observed by all the selected hospitals, training courses and comprehensive program conducting by each hospital could be enjoyed as practical tools to implement the all stages of healthcare waste management properly.

The contribution of waste management to the reduction of greenhouse gas emissions with applications in the city of Bucharest.

PubMed

Sandulescu, Elena

2004-12-01

Waste management is a key process to protect the environment and conserve resources. The contribution of appropriate waste management measures to the reduction of greenhouse gas (GHG) emissions from the city of Bucharest was studied. An analysis of the distribution of waste flows into various treatment options was conducted using the material flows and stocks analysis (MFSA). An optimum scenario (i.e. municipal solid waste stream managed as: recycling of recoverable materials, 8%; incineration of combustibles, 60%; landfilling of non-combustibles, 32%) was modelled to represent the future waste management in Bucharest with regard to its relevance towards the potential for GHG reduction. The results indicate that it can contribute by 5.5% to the reduction of the total amount of GHGs emitted from Bucharest.

The Dental Solid Waste Management in Different Categories of Dental Laboratories in Abha City, Saudi Arabia

PubMed Central

Haralur, Satheesh B.; Al-Qahtani, Ali S.; Al-Qarni, Marie M.; Al-Homrany, Rami M.; Aboalkhair, Ayyob E.; Madalakote, Sujatha S.

2015-01-01

Aim: To study the awareness, attitude, practice and facilities among the different categories of dental laboratories in Abha city. Materials and Methods: A total of 80 dental technicians were surveyed in the study. The dental laboratories included in the study were teaching institute (Group I), Government Hospital (Group II), Private Dental Clinic (Group III) and Independent laboratory (Group IV). The pre-tested anonymous questionnaire was used to understand knowledge, attitude, facilities, practice and orientation regarding biomedical waste management. Results: The knowledge of biomedical waste categories, colour coding and segregation was better among Group I (55-65%) and Group II (65-75%). The lowest standard of waste disposal was practiced at Group IV (15-20%) and Group III (25-35%). The availability of disposal facilities was poor at Group IV. The continuous education on biomedical waste management lacked in all the Groups. Conclusion: The significant improvement in disposal facilities was required at Group III and Group IV laboratories. All dental technicians were in need of regular training of biomedical waste management. Clinical Significance: The dental laboratories are an integral part of dental practice. The dental laboratories are actively involved in the generation, handling and disposal of biomedical waste. Hence, it is important to assess the biomedical waste management knowledge, attitude, facilities and practice among different categories of dental laboratories. PMID:26962373

Issues that Drive Waste Management Technology Development for Space Missions

NASA Technical Reports Server (NTRS)

Fisher, John W.; Levri, Julie A.; Hogan, John A.; Wignarajah, Kanapathipillai

2005-01-01

Waste management technologies for space life support systems are currently at low development levels. Manual compaction of waste in plastic bags and overboard disposal to earth return vehicles are the primary current waste management methods. Particularly on future missions, continuance of current waste management methods would tend to expose the crew to waste hazards, forfeit recoverable resources such as water, consume valuable crew time, contaminate planetary surfaces, and risk return to Earth of extraterrestrial life. Improvement of waste management capabilities is needed for adequate management of wastes. Improvements include recovery of water and other resources, conversion of waste to states harmless to humans, long-term containment of wastes, and disposal of waste. Current NASA requirements documents on waste management are generally not highly detailed. More detailed requirements are needed to guide the development of waste management technologies that will adequately manage waste. In addition to satisfying requirements, waste management technologies must also recover resources. Recovery of resources such as water and habitat volume can reduce mission cost. This paper explores the drivers for waste management technology development including requirements and resource recovery.

Students' Attitudes to Solid Waste Management in a Nigerian University: Implications for Campus-Based Sustainability Education

ERIC Educational Resources Information Center

Ifegbesan, Ayodeji Peter; Ogunyemi, Biodun; Rampedi, Isaac T.

2017-01-01

Purpose: Waste management is a critical element of the campus sustainability movement in which Nigerian universities are yet to actively participate. The purpose of this study was to investigate prevalent waste management practices and the disposition of undergraduate students in a Nigerian University. Design/methodology/approach: Data collection…

Environmental assessment of alternative municipal solid waste management strategies. A Spanish case study.

PubMed

Bovea, M D; Ibáñez-Forés, V; Gallardo, A; Colomer-Mendoza, F J

2010-11-01

The aim of this study is to compare, from an environmental point of view, different alternatives for the management of municipal solid waste generated in the town of Castellón de la Plana (Spain). This town currently produces 207 ton of waste per day and the waste management system employed today involves the collection of paper/cardboard, glass and light packaging from materials banks and of rest waste at street-side containers. The proposed alternative scenarios were based on a combination of the following elements: selective collection targets to be accomplished by the year 2015 as specified in the Spanish National Waste Plan (assuming they are reached to an extent of 50% and 100%), different collection models implemented nationally, and diverse treatments of both the separated biodegradable fraction and the rest waste to be disposed of on landfills. This resulted in 24 scenarios, whose environmental behaviour was studied by applying the life cycle assessment methodology. In accordance with the ISO 14040-44 (2006) standard, an inventory model was developed for the following stages of the waste management life cycle: pre-collection (bags and containers), collection, transport, pre-treatment (waste separation) and treatment/disposal (recycling, composting, biogasification+composting, landfill with/without energy recovery). Environmental indicators were obtained for different impact categories, which made it possible to identify the key variables in the waste management system and the scenario that offers the best environmental behaviour. Finally, a sensitivity analysis was used to test some of the assumptions made in the initial life cycle inventory model. Copyright © 2010 Elsevier Ltd. All rights reserved.

Toxicity potentials from waste cellular phones, and a waste management policy integrating consumer, corporate, and government responsibilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, Seong-Rin; Schoenung, Julie M., E-mail: jmschoenung@ucdavis.ed

Cellular phones have high environmental impact potentials because of their heavy metal content and current consumer attitudes toward purchasing new phones with higher functionality and neglecting to return waste phones into proper take-back systems. This study evaluates human health and ecological toxicity potentials from waste cellular phones; highlights consumer, corporate, and government responsibilities for effective waste management; and identifies key elements needed for an effective waste management strategy. The toxicity potentials are evaluated by using heavy metal content, respective characterization factors, and a pathway and impact model for heavy metals that considers end-of-life disposal in landfills or by incineration. Cancermore » potentials derive primarily from Pb and As; non-cancer potentials primarily from Cu and Pb; and ecotoxicity potentials primarily from Cu and Hg. These results are not completely in agreement with previous work in which leachability thresholds were the metric used to establish priority, thereby indicating the need for multiple or revised metrics. The triple bottom line of consumer, corporate, and government responsibilities is emphasized in terms of consumer attitudes, design for environment (DfE), and establishment and implementation of waste management systems including recycling streams, respectively. The key strategic elements for effective waste management include environmental taxation and a deposit-refund system to motivate consumer responsibility, which is linked and integrated with corporate and government responsibilities. The results of this study can contribute to DfE and waste management policy for cellular phones.« less

Projection of Big Cities Waste Management and Cost Based on Economic and Demographic Factors in Indonesia

NASA Astrophysics Data System (ADS)

Prajati, Gita; Padmi, Tri; Benno Rahardyan, dan

2017-12-01

Nowadays, solid waste management continues to be a major challenge in urban areas, especially in developing country. It is triggered by population growth, economic growth, industrialization and urbanization. Indonesia itselfs categorized into developing country. Indonesia's government has many program in order to increase the economic growth. One of them is MP3EI (Masterplan Percepatan dan Perluasan Pembangunan Ekonomi Indonesia. This program should be suppported by right waste management system. If Indonesia's waste management system can't afford the economic growth, it will trigger health and environmental problems. This study's purpose is to develop the socio-economic-environment model that can be used as a basis planning for the facility and cost of waste management systems. In this paper we used the development of Khajuria model test method. This method used six variables, which are GDP, population, population density, illiteracy, school's period and economic growth. The result showed that development of Khajuria test could explained the influence of economic and demographic factors to waste generation, 65.6%. The projection of waste generation shows that Pangkalpinang, Pekanbaru and Serang are the cities with the highest waste generation for the next five years. The number of dump truck and TPS in DKI Jakarata is the highest within another city, which is 39.37%. For the next five years, the waste management system in our study areas cost maximum 0.8% from GDP (Gross Domestic Products).

Toxicity potentials from waste cellular phones, and a waste management policy integrating consumer, corporate, and government responsibilities.

PubMed

Lim, Seong-Rin; Schoenung, Julie M

2010-01-01

Cellular phones have high environmental impact potentials because of their heavy metal content and current consumer attitudes toward purchasing new phones with higher functionality and neglecting to return waste phones into proper take-back systems. This study evaluates human health and ecological toxicity potentials from waste cellular phones; highlights consumer, corporate, and government responsibilities for effective waste management; and identifies key elements needed for an effective waste management strategy. The toxicity potentials are evaluated by using heavy metal content, respective characterization factors, and a pathway and impact model for heavy metals that considers end-of-life disposal in landfills or by incineration. Cancer potentials derive primarily from Pb and As; non-cancer potentials primarily from Cu and Pb; and ecotoxicity potentials primarily from Cu and Hg. These results are not completely in agreement with previous work in which leachability thresholds were the metric used to establish priority, thereby indicating the need for multiple or revised metrics. The triple bottom line of consumer, corporate, and government responsibilities is emphasized in terms of consumer attitudes, design for environment (DfE), and establishment and implementation of waste management systems including recycling streams, respectively. The key strategic elements for effective waste management include environmental taxation and a deposit-refund system to motivate consumer responsibility, which is linked and integrated with corporate and government responsibilities. The results of this study can contribute to DfE and waste management policy for cellular phones. 2010 Elsevier Ltd. All rights reserved.

Carbon footprint and energy use of food waste management options for fresh fruit and vegetables from supermarkets.

PubMed

Eriksson, Mattias; Spångberg, Johanna

2017-02-01

Food waste is a problem with economic, environmental and social implications, making it both important and complex. Previous studies have addressed food waste management options at the less prioritised end of the waste hierarchy, but information on more prioritised levels is also needed when selecting the best available waste management options. Investigating the global warming potential and primary energy use of different waste management options offers a limited perspective, but is still important for validating impacts from the waste hierarchy in a local context. This study compared the effect on greenhouse gas emissions and primary energy use of different food waste management scenarios in the city of Växjö, Sweden. A life cycle assessment was performed for four waste management scenarios (incineration, anaerobic digestion, conversion and donation), using five food products (bananas, tomatoes, apples, oranges and sweet peppers) from the fresh fruit and vegetables department in two supermarkets as examples when treated as individual waste streams. For all five waste streams, the established waste hierarchy was a useful tool for prioritising the various options, since the re-use options (conversion and donation) reduced the greenhouse gas emissions and the primary energy use to a significantly higher degree than the energy recovery options (incineration and anaerobic digestion). The substitution of other products and services had a major impact on the results in all scenarios. Re-use scenarios where food was replaced therefore had much higher potential to reduce environmental impact than the energy recovery scenarios where fossil fuel was replaced. This is due to the high level of resources needed to produce food compared with production of fossil fuels, but also to fresh fruit and vegetables having a high water content, making them inefficient as energy carriers. Waste valorisation measures should therefore focus on directing each type of food to the waste management system that can substitute the most resource-demanding products or services, even when the whole waste flow cannot be treated with the same method. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determining heavy metals in spent compact fluorescent lamps (CFLs) and their waste management challenges: Some strategies for improving current conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taghipour, Hassan, E-mail: hteir@yahoo.com; Amjad, Zahra; Jafarabadi, Mohamad Asghari

2014-07-15

Highlights: • Heavy metals in spent compact fluorescent lamps (CFLs) determined. • Current waste management condition of CFLs in Iran assessed. • Currently, waste of CFLs is disposed by municipal waste stream in waste landfills. • We propose extended producer responsibility (EPR) for CFLs waste management. - Abstract: From environmental viewpoint, the most important advantage of compact fluorescent lamps (CFLs) is reduction of green house gas emissions. But their significant disadvantage is disposal of spent lamps because of containing a few milligrams of toxic metals, especially mercury and lead. For a successful implementation of any waste management plan, availability ofmore » sufficient and accurate information on quantities and compositions of the generated waste and current management conditions is a fundamental prerequisite. In this study, CFLs were selected among 20 different brands in Iran. Content of heavy metals including mercury, lead, nickel, arsenic and chromium was determined by inductive coupled plasma (ICP). Two cities, Tehran and Tabriz, were selected for assessing the current waste management condition of CFLs. The study found that waste generation amount of CFLs in the country was about 159.80, 183.82 and 153.75 million per year in 2010, 2011 and 2012, respectively. Waste generation rate of CFLs in Iran was determined to be 2.05 per person in 2012. The average amount of mercury, lead, nickel, arsenic and chromium was 0.417, 2.33, 0.064, 0.056 and 0.012 mg per lamp, respectively. Currently, waste of CFLs is disposed by municipal waste stream in waste landfills. For improving the current conditions, we propose by considering the successful experience of extended producer responsibility (EPR) in other electronic waste management. The EPR program with advanced recycling fee (ARF) is implemented for collecting and then recycling CFLs. For encouraging consumers to take the spent CFLs back at the end of the products’ useful life, a proportion of ARF (for example, 50%) can be refunded. On the other hand, the government and Environmental Protection Agency should support and encourage recycling companies of CFLs both technically and financially in the first place.« less

Solid Waste Management Plan. Revision 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-04-26

The waste types discussed in this Solid Waste Management Plan are Municipal Solid Waste, Hazardous Waste, Low-Level Mixed Waste, Low-Level Radioactive Waste, and Transuranic Waste. The plan describes for each type of solid waste, the existing waste management facilities, the issues, and the assumptions used to develop the current management plan.

Estimation of construction waste generation and management in Thailand.

PubMed

Kofoworola, Oyeshola Femi; Gheewala, Shabbir H

2009-02-01

This study examines construction waste generation and management in Thailand. It is estimated that between 2002 and 2005, an average of 1.1 million tons of construction waste was generated per year in Thailand. This constitutes about 7.7% of the total amount of waste disposed in both landfills and open dumpsites annually during the same period. Although construction waste constitutes a major source of waste in terms of volume and weight, its management and recycling are yet to be effectively practiced in Thailand. Recently, the management of construction waste is being given attention due to its rapidly increasing unregulated dumping in undesignated areas, and recycling is being promoted as a method of managing this waste. If effectively implemented, its potential economic and social benefits are immense. It was estimated that between 70 and 4,000 jobs would have been created between 2002 and 2005, if all construction wastes in Thailand had been recycled. Additionally it would have contributed an average savings of about 3.0 x 10(5) GJ per year in the final energy consumed by the construction sector of the nation within the same period based on the recycling scenario analyzed. The current national integrated waste management plan could enhance the effective recycling of construction and demolition waste in Thailand when enforced. It is recommended that an inventory of all construction waste generated in the country be carried out in order to assess the feasibility of large scale recycling of construction and demolition waste.

Characteristics and management of infectious industrial waste in Taiwan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, M.-C.; Lin, Jim Juimin

Infectious industrial waste management in Taiwan is based on the specific waste production unit. In other countries, management is based simply on whether the producer may lead to infectious disease. Thus, Taiwan has a more detailed classification of infectious waste. The advantage of this classification is that it is easy to identify the sources, while the disadvantage lies in the fact that it is not flexible and hence increases cost. This study presents an overview of current management practices for handling infectious industrial waste in Taiwan, and addresses the current waste disposal methods. The number of small clinics in Taiwanmore » increased from 18,183 to 18,877 between 2003 and 2005. Analysis of the data between 2003 and 2005 showed that the majority of medical waste was general industrial waste, which accounted for 76.9%-79.4% of total medical waste. Infectious industrial waste accounted for 19.3%-21.9% of total medical waste. After the SARS event in Taiwan, the amount of infectious waste reached 19,350 tons in 2004, an increase over the previous year of 4000 tons. Waste minimization was a common consideration for all types of waste treatment. In this study, we summarize the percentage of plastic waste in flammable infectious industrial waste generated by medical units, which, in Taiwan was about 30%. The EPA and Taiwan Department of Health have actively promoted different recycling and waste reduction measures. However, the wide adoption of disposable materials made recycling and waste reduction difficult for some hospitals. It has been suggested that enhancing the education of and promoting communication between medical units and recycling industries must be implemented to prevent recyclable waste from entering the incinerator.« less

Healthcare waste management practices and risk perceptions: findings from hospitals in the Algarve region, Portugal.

PubMed

Ferreira, Vera; Teixeira, Margarida Ribau

2010-12-01

The management of healthcare wastes is receiving greater attention because of the risks to both human health and the environment caused by inadequate waste management practices. In that context, the objective of this study was to analyse the healthcare waste management practices in hospitals of the Algarve region, Portugal, and in particular to assess the risk perceptions of, and actual risk to, healthcare staff. The study included three of the six hospitals in the region, covering 41% of the bed capacity. Data were collected via surveys, interviews, and on-site observations. The results indicate that waste separation is the main deficiency in healthcare waste practice, with correct separation being positively related to the degree of daily contact with the waste. Risk perceptions of healthcare staff show the highest levels for the environment (4.24) and waste workers (4.08), and the lowest for patients (3.29) and visitors (2.80), again being positively associated with the degree of daily contact. Risk perceptions of healthcare staff are related to the difficulties of the correct separation of wastes and the lack of knowledge concerning the importance of that separation. The risk of infection with needlesticks/sharps is higher during patient care than during waste handling, and the frequency of these injuries is related to the daily tasks of each healthcare group (doctors, nurses, and housekeepers). Furthermore, legislative definitions and classifications of healthcare wastes appear to have conditioned the management practices associated with, and the perceptions of risk concerning, healthcare wastes. Copyright © 2010 Elsevier Ltd. All rights reserved.

Comparative lifecycle assessment of alternatives for waste management in Rio de Janeiro - Investigating the influence of an attributional or consequential approach.

PubMed

Bernstad Saraiva, A; Souza, R G; Valle, R A B

2017-10-01

The environmental impacts from three management alternatives for organic fraction of municipal solid waste were compared using lifecycle assessment methodology. The alternatives (sanitary landfill, selective collection of organic waste for anaerobic digestion and anaerobic digestion after post-separation of organic waste) were modelled applying an attributional as well as consequential approach, in parallel with the aim of identifying if and how these approaches can affect results and conclusions. The marginal processes identified in the consequential modelling were in general associated with higher environmental impacts than average processes modelled with an attributional approach. As all investigated waste management alternatives result in net-substitution of energy and in some cases also materials, the consequential modelling resulted in lower absolute environmental impacts in five of the seven environmental impact categories assessed in the study. In three of these, the chosen modelling approach can alter the hierarchy between compared waste management alternatives. This indicates a risk of underestimating potential benefits from efficient energy recovery from waste when applying attributional modelling in contexts in which electricity provision historically has been dominated by technologies presenting rather low environmental impacts, but where projections point at increasing impacts from electricity provision in coming years. Thus, in the present case study, the chosen approach affects both absolute and relative results from the comparison. However, results were largely related to the processes identified as affected by investigated changes, and not merely the chosen modelling approach. The processes actually affected by future choices between different waste management alternatives are intrinsically uncertain. The study demonstrates the benefits of applying different assumptions regarding the processes affected by investigated choices - both for provision of energy and materials substituted by waste management processes in consequential LCA modelling, in order to present outcomes that are relevant as decision support within the waste management sector. Copyright © 2017 Elsevier Ltd. All rights reserved.

Waste flow analysis and life cycle assessment of integrated waste management systems as planning tools: Application to optimise the system of the City of Bologna.

PubMed

Tunesi, Simonetta; Baroni, Sergio; Boarini, Sandro

2016-09-01

The results of this case study are used to argue that waste management planning should follow a detailed process, adequately confronting the complexity of the waste management problems and the specificity of each urban area and of regional/national situations. To support the development or completion of integrated waste management systems, this article proposes a planning method based on: (1) the detailed analysis of waste flows and (2) the application of a life cycle assessment to compare alternative scenarios and optimise solutions. The evolution of the City of Bologna waste management system is used to show how this approach can be applied to assess which elements improve environmental performance. The assessment of the contribution of each waste management phase in the Bologna integrated waste management system has proven that the changes applied from 2013 to 2017 result in a significant improvement of the environmental performance mainly as a consequence of the optimised integration between materials and energy recovery: Global Warming Potential at 100 years (GWP100) diminishes from 21,949 to -11,169 t CO2-eq y(-1) and abiotic resources depletion from -403 to -520 t antimony-eq. y(-1) This study analyses at great detail the collection phase. Outcomes provide specific operational recommendations to policy makers, showing the: (a) relevance of the choice of the materials forming the bags for 'door to door' collection (for non-recycled low-density polyethylene bags 22 kg CO2-eq (tonne of waste)(-1)); (b) relatively low environmental impacts associated with underground tanks (3.9 kg CO2-eq (tonne of waste)(-1)); (c) relatively low impact of big street containers with respect to plastic bags (2.6 kg CO2-eq. (tonne of waste)(-1)). © The Author(s) 2016.

Pomace waste management scenarios in Québec--impact on greenhouse gas emissions.

PubMed

Gassara, Fatma; Brar, S K; Pelletier, F; Verma, M; Godbout, S; Tyagi, R D

2011-09-15

Fruit processing industries generate tremendous amount of solid wastes which is almost 35-40% dry weight of the total produce used for the manufacturing of juices. These solid wastes, referred to as, "pomace" contain high moisture content (70-75%) and biodegradable organic load (high BOD and COD values) so that their management is an important issue. During the management of these pomace wastes by different strategies comprising incineration, landfill, composting, solid-state fermentation to produce high-value enzymes and animal feed, there is production of greenhouse gases (GHG) which must be taken into account. In this perspective, this study is unique that discusses the GHG emission analysis of agro-industrial waste management strategies, especially apple pomace waste management and repercussions of value-addition of these wastes in terms of their sustainability using life cycle assessment (LCA) model. The results of the analysis indicated that, among all the apple pomace management sub-models for a functional unit, solid-state fermentation to produce enzymes was the most effective method for reducing GHG emissions (906.81 tons CO(2) eq. per year), while apple pomace landfill resulted in higher GHG emissions (1841.00 tons CO(2) eq. per year). The assessment and inventory of GHG emissions during solid-state fermentation gave positive indications of environmental sustainability for the use of this strategy to manage apple pomace and other agricultural wastes, particularly in Quebec and also extended to other countries. The analysis and use of parameters in this study were drawn from various analytical approaches and data sources. There was absence of some data in the literature which led to consideration of some assumptions in order to calculate GHG emissions. Hence, supplementary experimental studies will be very important to calculate the GHG emissions coefficients during agro-industrial waste management. Copyright © 2011 Elsevier B.V. All rights reserved.

Physical space and its impact on waste management in the neonatal care setting

PubMed Central

Manzi, Sean

2014-01-01

This paper reports an investigation intended to obtain some understanding of how the working environment might influence the practice and knowledge of those involved in the management of healthcare waste. The National Health Service (NHS) has a continuing waste problem, and the way it manages waste harms the environment and consumes resources. It has been estimated that the carbon footprint of the NHS in England is approximately 20 million tons of CO2e. It has been suggested that better waste segregation could lead to more effective recycling, saving up to 42,000 tonnes of CO2. This qualitative study employed non-participant observation and semi-structured interviews. The interviews were carried out with the key informants within the participating neonatal intensive care unit. Findings from this study indicate that space and the physical arrangement of the environment are significant and influential factors in clinical practice. Where the clinical environment is not supportive, poor infection control and waste management practice is likely to occur. However, proximity of staff caused by a lack of physical space might facilitate situated learning and a collective development of knowledge in practice. The implementation of sustainable waste management practices would be more likely to succeed in an environment that facilitates correct waste segregation. PMID:28989373

Household waste compositional analysis variation from insular communities in the framework of waste prevention strategy plans.

PubMed

Zorpas, Antonis A; Lasaridi, Katia; Voukkali, Irene; Loizia, Pantelitsa; Chroni, Christina

2015-04-01

Waste management planning requires reliable data regarding waste generation, affecting factors on waste generation and forecasts of waste quantities based on facts. In order to decrease the environmental impacts of waste management the choice of prevention plan as well as the treatment method must be based on the features of the waste that are produced in a specific area. Factors such as culture, economic development, climate, and energy sources have an impact on waste composition; composition influences the need of collecting waste more or less frequently of waste collection and disposition. The research question was to discover the main barriers concerning the compositional analysis in Insular Communities under warm climate conditions and the findings from this study enabled the main contents of a waste management plan to be established. These included advice to residents on waste minimisation, liaison with stakeholders and the expansion of kerbside recycling schemes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of municipal solid waste management performance by material flow analysis: Theoretical approach and case study.

PubMed

Zaccariello, Lucio; Cremiato, Raffaele; Mastellone, Maria Laura

2015-10-01

The main role of a waste management plan is to define which is the combination of waste management strategies and method needed to collect and manage the waste in such a way to ensure a given set of targets is reached. Objectives have to be sustainable and realistic, consistent with the environmental policies and regulations and monitored to verify the progressive achievement of the given targets. To get the aim, the setting up and quantification of indicators can allow the measurement of efficiency of a waste management system. The quantification of efficiency indicators requires the developing of a material flow analysis over the system boundary, from waste collection to secondary materials selling, processing and disposal. The material flow analysis has been carried out with reference to a case study for which a reliable, time- and site-specific database was available. The material flow analysis allowed the evaluation of the amount of materials sent to recycling, to landfilling and to waste-to-energy, by highlighting that the sorting of residual waste can further increase the secondary materials amount. The utilisation of energy recovery to treat the low-grade waste allows the maximisation of waste diversion from landfill with a low production of hazardous ash. A preliminary economic balance has been carried out to define the gate fee of the waste management system that was in the range of 84-145 € t(-1) without including the separate collection cost. The cost of door-by-door separate collection, designed to ensure the collection of five separate streams, resulted in 250 € t(-1) ±30%. © The Author(s) 2015.

Solid waste management in primary healthcare centers: application of a facilitation tool 1

PubMed Central

Moreira, Ana Maria Maniero; Günther, Wanda Maria Risso

2016-01-01

Abstract Objectives: to propose a tool to facilitate diagnosis, formulation and evaluation of the Waste Management Plan in Primary Healthcare Centers and to present the results of the application in four selected units. Method: descriptive research, covering the stages of formulation /application of the proposed instrument and the evaluation of waste management performance at the units. Results: the tool consists in five forms; specific indicators of waste generation for outpatients healthcare units were proposed, and performance indicators that give scores for compliance with current legislation. In the studied units it is generated common waste (52-60%), infectious-sharps (31-42%) and recyclable (5-17%). The average rates of generation are: 0,09kg of total waste/outpatient assistance and 0,09kg of infectious-sharps waste/outpatient procedure. The compliance with regulations, initially 26-30%, then reached 30-38% a year later. Conclusion: the tool showed to be easy to use, bypassing the existence of a complex range of existing regulatory requirements, allowed to identify non-conformities, pointed out corrective measures and evaluated the performance of waste management. In this sense, it contributes to decision making and management practices relating to waste, tasks usually assigned to nurses. It is recommended that the tool be applied in similar healthcare units for comparative studies, and implementation of necessary adaptations for other medical services. PMID:27556874

Super Saver Investigators: An Elementary, Interdisciplinary, Environmental Studies Activity Guidebook about Solid Waste and Natural Resources.

ERIC Educational Resources Information Center

Landis, David; And Others

This is an elementary, interdisciplinary, environmental studies activity guidebook about solid waste and natural resources. "Super Saver Investigators" what solid waste is, where it is generated, how we manage it and could manage it better, and the consequence of mismanagement. It contains many hands-on, skill enhancing activities for…

40 CFR 273.33 - Waste management.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Waste management. 273.33 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Large Quantity Handlers of Universal Waste § 273.33 Waste management. (a) Universal waste batteries. A large quantity handler of universal waste must manage...

40 CFR 273.13 - Waste management.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Waste management. 273.13 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Small Quantity Handlers of Universal Waste § 273.13 Waste management. (a) Universal waste batteries. A small quantity handler of universal waste must manage...

Investigating solid waste production and associated management practices in private dental units

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kontogianni, S.; Xirogiannopoulou, A.; Karagiannidis, A.

In the municipality of Thessaloniki in 2006 mercury-bearing dental wastes were not managed properly by 80% of dentists and metal-bearing waste was handled in accordance with internationally established best management practices by less than 50% of dentists. Those results were documented through a biennial field-based research study that took place in private dental units within the Thessaloniki Urban Area. For quantifying the waste produced, structured questionnaires were used and interviews with dentists were performed. In the present work, results of this survey are presented; critical parameters and factors affecting the quantity and quality of the dental waste stream are reportedmore » together with the analysis and classification of dominant conditions and needs of the dental sector in the waste management field.« less

Developing a Novel, Sustainable and Beneficial System for the Systematic Management of Hospital Wastes

PubMed Central

Hinduja, Indira N.; Ahuja, Harish S.

2016-01-01

Introduction India is the 2nd most populated country in the world. Population of India is increasing at a tremendous rate. Proportionately, the numbers of people seeking health care are increasing. In that ratio the quantities of hospital wastes, in wider terms, healthcare wastes that are getting generated is also increasing. Current methods for the safe disposal of healthcare wastes are not able to cope up with the rate of generation of healthcare wastes and moreover are not eco-friendly at all. Due to this, the current rules and regulations regarding the safe disposal of healthcare wastes are getting violated, ultimately leading to improper management of healthcare wastes, posing a serious threat to the environment and to the community. Aim To develop a novel, sustainable and beneficial system for the systematic management of healthcare wastes utilizing the strategies of waste reduction, waste segregation and recycling of Non Hazardous Hospital Wastes (NHHWs). Materials and Methods Firstly a detailed study of the Healthcare Waste Management System (HCWMS) operational at the Jaslok Hospital and Research Centre was done. A pilot study was then performed. After that, data regarding the generation and management of healthcare wastes in the other healthcare settings was collected and analyzed. Considering all this, a novel, sustainable and beneficial template system for the systematic management of healthcare wastes was proposed. Lastly the possible positive impacts from the implementation of HCWMSs designed using proposed template HCWMS in significant numbers of healthcare establishments was gauged. Results The healthcare waste management system operational at the Jaslok Hospital and Research Centre was found to be very efficient and provided vital inputs about developing the novel HCWMS. The pilot study was successfully completed generating significant revenue from the hospital’s own NHHWs while managing them in an eco-friendly way. The total healthcare waste generation in Maharashtra was approximately estimated at about 2,89,200kg/day of which about 43,380kg/day was Bio-Medical Wastes (BMWs) while about 2,45,820kg/day were the NHHWs. This stresses the need of implementing HCWMSs in Healthcare Establishments (HCEs) based on the proposed novel template of HCWMS. Conclusion The novel template system is proposed in a detailed manner under various heads in the form of a handbook which is scalable upwards or downwards as per the requirement of a HCE. The enormous economic and environmental positive impacts from the implementation of the HCWMSs based on the proposed HCWMS in significant numbers of HCEs were presented numerically, putting light on the necessity and tremendous potential of this field of research. PMID:27790471

Assessment of College Students' Knowledge and Attitudes toward Solid Waste Management in North Central Zone of Nigeria

ERIC Educational Resources Information Center

Dung, Mohammed Dauda; Makilik, Mangut; Ozoji, Bernadette Ebele

2017-01-01

This study focused on assessment of colleges of education students' knowledge and attitudes toward solid waste management in the North Central zone of Nigeria. The cross-sectional survey design was adopted. A students' knowledge and attitudes toward solid waste management questionnaire were used to collect data from 1,800 students. The findings…

Waste management in primary healthcare centres of Iran.

PubMed

Mesdaghinia, Alireza; Naddafi, Kazem; Mahvi, Amir Hossein; Saeedi, Reza

2009-06-01

The waste management practices in primary healthcare centres of Iran were investigated in the present study. A total of 120 primary healthcare centres located across the country were selected using the cluster sampling method and the current situation of healthcare waste management was determined through field investigation. The quantities of solid waste and wastewater generation per outpatient were found to be 60 g outpatient(-1) day(-1) and 26 L outpatient(-1) day(-1), respectively. In all of the facilities, sharp objects were separated almost completely, but separation of other types of hazardous healthcare solid waste was only done in 25% of the centres. The separated hazardous solid waste materials were treated by incineration, temporary incineration and open burning methods in 32.5, 8.3 and 42.5% of the healthcare centres, respectively. In 16.7% of the centres the hazardous solid wastes were disposed of without any treatment. These results indicate that the management of waste materials in primary healthcare centres in Iran faced some problems. Staff training and awareness, separation of healthcare solid waste, establishment of the autoclave method for healthcare solid waste treatment and construction of septic tanks and disinfection units in the centres that were without access to a sewer system are the major measures that are suggested for improvement of the waste management practices.

Healthcare waste management: current practices in selected healthcare facilities, Botswana.

PubMed

Mbongwe, Bontle; Mmereki, Baagi T; Magashula, Andrew

2008-01-01

Healthcare waste management continues to present an array of challenges for developing countries, and Botswana is no exception. The possible impact of healthcare waste on public health and the environment has received a lot of attention such that Waste Management dedicated a special issue to the management of healthcare waste (Healthcare Wastes Management, 2005. Waste Management 25(6) 567-665). As the demand for more healthcare facilities increases, there is also an increase on waste generation from these facilities. This situation requires an organised system of healthcare waste management to curb public health risks as well as occupational hazards among healthcare workers as a result of poor waste management. This paper reviews current waste management practices at the healthcare facility level and proposes possible options for improvement in Botswana.

Evaluation of composting as a strategy for managing organic wastes from a municipal market in Nicaragua.

PubMed

Aulinas Masó, Montserrat; Bonmatí Blasi, August

2008-07-01

A pilot-scale study was undertaken to evaluate alternatives to the solid waste management of a Central American municipal market located in Estelí, Nicaragua. The municipal solid waste from the local market is the second largest contributor to the municipal solid waste (MSW) stream. Waste from the market without any previous sorting or treatment is open dumped. The options evaluated in this study were windrow composting, windrow composting with yard waste, bokashi and vermicompost. Significant differences between the properties of composts produced were found; however, all of them reduce the initial waste volume and are potential useful agronomic products for a survival agrarian milieu.

Elements affecting food waste in the food service sector.

PubMed

Heikkilä, Lotta; Reinikainen, Anu; Katajajuuri, Juha-Matti; Silvennoinen, Kirsi; Hartikainen, Hanna

2016-10-01

Avoidable food waste is produced in the food service sector, with significant ecological and economical impacts. In order to understand and explain better the complex issue of food waste a qualitative study was conducted on the reasons for its generation in restaurants and catering businesses. Research data were collected during three participatory workshops for personnel from three different catering sector companies in Finland. Based on synthesized qualitative content analysis, eight elements influencing production and reduction of food waste were identified. Results revealed the diversity of managing food waste in the food service sector and how a holistic approach is required to prevent and reduce it. It is crucial to understand that food waste is manageable and should be an integral component of the management system. The model of eight factors provides a framework for recognition and management of food waste in the food service sector. Copyright © 2016 Elsevier Ltd. All rights reserved.

Optimal waste-to-energy strategy assisted by GIS For sustainable solid waste management

NASA Astrophysics Data System (ADS)

Tan, S. T.; Hashim, H.

2014-02-01

Municipal solid waste (MSW) management has become more complex and costly with the rapid socio-economic development and increased volume of waste. Planning a sustainable regional waste management strategy is a critical step for the decision maker. There is a great potential for MSW to be used for the generation of renewable energy through waste incineration or landfilling with gas capture system. However, due to high processing cost and cost of resource transportation and distribution throughout the waste collection station and power plant, MSW is mostly disposed in the landfill. This paper presents an optimization model incorporated with GIS data inputs for MSW management. The model can design the multi-period waste-to-energy (WTE) strategy to illustrate the economic potential and tradeoffs for MSW management under different scenarios. The model is capable of predicting the optimal generation, capacity, type of WTE conversion technology and location for the operation and construction of new WTE power plants to satisfy the increased energy demand by 2025 in the most profitable way. Iskandar Malaysia region was chosen as the model city for this study.

Assessing resident awareness on e-waste management in Bangalore, India: a preliminary case study.

PubMed

Awasthi, Abhishek Kumar; Li, Jinhui

2018-04-01

The generation of e-waste has increased significantly in India, and the informal recycling of e-waste has adverse effects on environment and public health. In this article, the E-waste management is evaluated in accordance from the resident's awareness perspective in Bangalore city, India. The survey data revealed that about 58% male and 42% female responded and 35% of the participants belong to age range between 18 and 25 years. About 60% of respondent's education level was either graduate or post graduate, 27% high school to higher school, 10% higher educated (> post graduate), and 3% primary to middle. Only 30% of the respondents were confident with e-waste rules and regulation, while 39% of the respondents were of very little information. Indian e-waste management has been improving for the last few years and it continues to develop. Therefore, the findings can be valuable for better understanding the resident's awareness for e-waste management and also need to promote the environmentally sound management of e-waste in Bangalore, India.

Evaluation of greenhouse gas emissions from waste management approaches in the islands.

PubMed

Chen, Ying-Chu

2017-07-01

Concerns about waste generation and climate change have attracted worldwide attention. Small islands, which account for more than one-sixth of the global land area, are facing problems caused by global climate change. This study evaluated the greenhouse gas emissions from five small islands surrounding Taiwan. These islands - Penghu County, Liuqui Island, Kinmen County, Matsu Island and Green Island - have their own waste management approaches that can serve as a guideline for waste management with greenhouse gas mitigation. The findings indicate that the total annual greenhouse gas emissions of the islands ranged from 292.1 to 29,096.2 [metric] tonne CO 2 -equivalent. The loading waste volumes and shipping distances were positively related to greenhouse gas emissions from transportation. The greenhouse gas emissions from waste-to-energy plants, mainly carbon dioxide and nitrous oxide, can be offset by energy recovery (approximately 38.6% of greenhouse gas emissions from incineration). In addition, about 34% and 11% of waste generated on the islands was successfully recycled and composted, respectively. This study provides valuable insights into the applicability of a policy framework for waste management approaches for greenhouse gas mitigation.

Energy implications of the thermal recovery of biodegradable municipal waste materials in the United Kingdom.

PubMed

Burnley, Stephen; Phillips, Rhiannon; Coleman, Terry; Rampling, Terence

2011-01-01

Waste management policies and legislation in many developed countries call for a reduction in the quantity of biodegradable waste landfilled. Anaerobic digestion, combustion and gasification are options for managing biodegradable waste while generating renewable energy. However, very little research has been carried to establish the overall energy balance of the collection, preparation and energy recovery processes for different types of wastes. Without this information, it is impossible to determine the optimum method for managing a particular waste to recover renewable energy. In this study, energy balances were carried out for the thermal processing of food waste, garden waste, wood, waste paper and the non-recyclable fraction of municipal waste. For all of these wastes, combustion in dedicated facilities or incineration with the municipal waste stream was the most energy-advantageous option. However, we identified a lack of reliable information on the energy consumed in collecting individual wastes and preparing the wastes for thermal processing. There was also little reliable information on the performance and efficiency of anaerobic digestion and gasification facilities for waste. Copyright © 2011 Elsevier Ltd. All rights reserved.

Factors affecting waste generation: a study in a waste management program in Dhaka City, Bangladesh.

PubMed

Afroz, Rafia; Hanaki, Keisuke; Tudin, Rabaah

2011-08-01

Information on waste generation, socioeconomic characteristics, and willingness of the households to separate waste was obtained from interviews with 402 respondents in Dhaka city. Ordinary least square regression was used to determine the dominant factors that might influence the waste generation of the households. The results showed that the waste generation of the households in Dhaka city was significantly affected by household size, income, concern about the environment, and willingness to separate the waste. These factors are necessary to effectively improve waste management, growth and performance, as well as to reduce the environmental degradation of the household waste.

Comparative study of solid waste management system based on building types in Palembang city

NASA Astrophysics Data System (ADS)

Jimmyanto, Hendrik; Dahlan, Hatta; Zahri, Imron

2017-11-01

Most of the solid waste generation sources come from housing activities. The types of house buildings located in the Palembang is a traditional building which made from wood construction and a permanent house which made from concrete construction. The aim of this study is to calculate the amount of waste generation and to study the community behavior in waste management. The research used an observation and questionnaires that took place in 3 location of the traditional housing and 3 location of the permanent housing with 20 respondents for each location. The results showed that the waste generation in the traditional housing was 1.51 liters/person/day and the permanent housing was 1.63 liters/person/day. The collecting system in traditional housing was taken by the garbage cart every 1 days, while in permanent housing was taken by motorcycle, pick-up car, or dump truck every 1 or 2 days. The questionnaire results showed that 96,67% of the traditional housing and 91,67% of the permanent housing disposed of the waste in a mix condition. Amount of 6,67 % from the traditional housing and 0% of permanent housing managed their waste into compost. Amount of 15 % from traditional housing and 3,33% of permanent housing sold their waste. Based on the results, it can be concluded that the permanent housing has the largest number of waste generation and the people in traditional housing had a tendency to manage the waste better than the permanent housing.

Assessment of health-care waste management in a humanitarian crisis: A case study of the Gaza Strip.

PubMed

Caniato, Marco; Tudor, Terry Louis; Vaccari, Mentore

2016-12-01

Health-care waste management requires technical, financial and human resources, and it is a challenge for low- and middle income countries, while it is often neglected in protracted crisis or emergency situations. Indeed, when health, safety, security or wellbeing of a community is threatened, solid waste management usually receives limited attention. Using the Gaza Strip as the case study region, this manuscript reports on health-care waste management within the context of a humanitarian crisis. The study employed a range of methods including content analyses of policies and legislation, audits of waste arisings, field visits, stakeholder interviews and evaluation of treatment systems. The study estimated a production from clinics and hospitals of 683kg/day of hazardous waste in the Gaza Strip, while the total health-care waste production was 3357 kg/day. A number of challenges was identified including lack of clear definitions and regulations, limited accurate data on which to base decisions and strategies and poor coordination amongst key stakeholders. Hazardous and non-hazardous waste was partially segregated and treatment facilities hardly used, and 75% of the hazardous waste was left untreated. Recommendations for mitigating these challenges posed to patients, staff and the community in general are suggested. The outputs are particularly useful to support decision makers, and re-organize the system according to reliable data and sound assumptions. The methodology can be replicated in other humanitarian settings, also to other waste flows, and other sectors of environmental sanitation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessing future scenarios for health care waste management using a multi-criteria decision analysis tool: A case study in the Turkish West Black Sea Region.

PubMed

Ciplak, Nesli

2015-08-01

The aim of this paper is to identify the best possible health care waste management option in the West Black Sea Region by taking into account economic, social, environmental, and technical aspects in the concept of multi-criteria decision analysis. In the scope of this research, three different health care waste management scenarios that consist of different technology alternatives were developed and compared using a decision-making computer software, called Right Choice, by identifying various criteria, measuring them, and ranking their relative importance from the point of key stakeholders. The results of the study show that the decentralized autoclave technology option coupled with the disposal through land-filling with energy recovery has potential to be an optimum option for health care waste management system, and an efficient health care waste segregation scheme should be given more attention by the authorities in the region. Furthermore, the discussion of the results points out multidisciplinary approach and the equilibrium between social, environmental, economic, and technical criteria. The methodology used in this research was developed in order to enable the decision makers to gain an increased perception of a decision problem. In general, the results and remarks of this study can be used as a basis of future planning and anticipation of needs for investment in the area of health care waste management in the region and also in developing countries that are dealing with the similar waste management problems.

Sustainable solutions for solid waste management in Southeast Asian countries.

PubMed

Ngoc, Uyen Nguyen; Schnitzer, Hans

2009-06-01

Human activities generate waste and the amounts tend to increase as the demand for quality of life increases. Today's rate in the Southeast Asian Nations (ASEANs) is alarming, posing a challenge to governments regarding environmental pollution in the recent years. The expectation is that eventually waste treatment and waste prevention approaches will develop towards sustainable waste management solutions. This expectation is for instance reflected in the term 'zero emission systems'. The concept of zero emissions can be applied successfully with today's technical possibilities in the agro-based processing industry. First, the state-of-the-art of waste management in Southeast Asian countries will be outlined in this paper, followed by waste generation rates, sources, and composition, as well as future trends of waste. Further on, solutions for solid waste management will be reviewed in the discussions of sustainable waste management. The paper emphasizes the concept of waste prevention through utilization of all wastes as process inputs, leading to the possibility of creating an ecosystem in a loop of materials. Also, a case study, focusing on the citrus processing industry, is displayed to illustrate the application of the aggregated material input-output model in a widespread processing industry in ASEAN. The model can be shown as a closed cluster, which permits an identification of opportunities for reducing environmental impacts at the process level in the food processing industry. Throughout the discussion in this paper, the utilization of renewable energy and economic aspects are considered to adapt to environmental and economic issues and the aim of eco-efficiency. Additionally, the opportunities and constraints of waste management will be discussed.

Solid waste management practices in wet coffee processing industries of Gidabo watershed, Ethiopia.

PubMed

Ulsido, Mihret D; Li, Meng

2016-07-01

The financial and social contributions of coffee processing industries within most coffee export-based national economies like Ethiopia are generally high. The type and amount of waste produced and the waste management options adopted by these industries can have negative effects on the environment. This study investigated the solid waste management options adopted in wet coffee processing industries in the Gidabo watershed of Ethiopia. A field observation and assessment were made to identify whether the operational characteristics of the industries have any effect on the waste management options that were practiced. The investigation was conducted on 125 wet coffee processing industries about their solid waste handling techniques. Focus group discussion, structured questionnaires, key informant interview and transect walks are some of the tools employed during the investigation. Two major types of wastes, namely hull-bean-pulp blended solid waste and wastewater rich in dissolved and suspended solids were generated in the industries. Wet mills, on average, released 20.69% green coffee bean, 18.58% water and 60.74% pulp by weight. Even though these wastes are rich in organic matter and recyclables; the most favoured solid waste management options in the watershed were disposal (50.4%) and industrial or household composting (49.6%). Laxity and impulsive decision are the driving motives behind solid waste management in Gidabo watershed. Therefore, to reduce possible contamination of the environment, wastes generated during the processing of red coffee cherries, such as coffee wet mill solid wastes, should be handled properly and effectively through maximisation of their benefits with minimised losses. © The Author(s) 2016.

Bio-Medical Waste Managment in a Tertiary Care Hospital: An Overview.

PubMed

Pandey, Anita; Ahuja, Sanjiv; Madan, Molly; Asthana, Ajay Kumar

2016-11-01

Bio-Medical Waste (BMW) management is of utmost importance as its improper management poses serious threat to health care workers, waste handlers, patients, care givers, community and finally the environment. Simultaneously, the health care providers should know the quantity of waste generated in their facility and try to reduce the waste generation in day-to-day work because lesser amount of BMW means a lesser burden on waste disposal work and cost saving. To have an overview of management of BMW in a tertiary care teaching hospital so that effective interventions and implementations can be carried out for better outcome. The observational study was carried out over a period of five months from January 2016 to May 2016 in Chhatrapati Shivaji Subharti Hospital, Meerut by the Infection Control Team (ICT). Assessment of knowledge was carried out by asking set of questions individually and practice regarding awareness of BMW Management among the Health Care Personnel (HCP) was carried out by direct observation in the workplace. Further, the total BMW generated from the present setup in kilogram per bed per day was calculated by dividing the mean waste generated per day by the number of occupied beds. Segregation of BMW was being done at the site of generation in almost all the areas of the hospital in color coded polythene bags as per the hospital protocol. The different types of waste being collected were infectious solid waste in red bag, soiled infectious waste in yellow bag and sharp waste in puncture proof container and blue bag. Though awareness (knowledge) about segregation of BMW was seen in 90% of the HCP, 30%-35% did not practice. Out of the total waste generated (57912 kg.), 8686.8 kg. (15%) was infectious waste. Average infectious waste generated was 0.341 Kg per bed per day. The transport, treatment and disposal of each collected waste were outsourced and carried out by 'Synergy' waste management Pvt. Ltd. The practice of BMW Management was lacking in 30-35% HCP which may lead to mixing of the 15% infectious waste with the remaining non-infectious. Therefore, training courses and awareness programs about BMW management will be carried out every month targeting smaller groups.

Assessment of medical waste management in seven hospitals in Lagos, Nigeria.

PubMed

Awodele, Olufunsho; Adewoye, Aishat Abiodun; Oparah, Azuka Cyril

2016-03-15

Medical waste (MW) can be generated in hospitals, clinics and places where diagnosis and treatment are conducted. The management of these wastes is an issue of great concern and importance in view of potential public health risks associated with such wastes. The study assessed the medical waste management practices in selected hospitals and also determined the impact of Lagos Waste Management Authority (LAWMA) intervention programs. A descriptive cross-sectional survey method was used. Data were collected using three instrument (questionnaire, site visitation and in -depth interview). Two public (hospital A, B) and five private (hospital C, D, E, F and G) which provide services for low, middle and high income earners were used. Data analysis was done with SPSS version 20. Chi-squared test was used to determine level of significance at p < 0.05. The majority 56 (53.3%) of the respondents were females with mean age of 35.46 (±1.66) years. The hospital surveyed, except hospital D, disposes both general and medical waste separately. All the facilities have the same process of managing their waste which is segregation, collection/on-site transportation, on-site storage and off-site transportation. Staff responsible for collecting medical waste uses mainly hand gloves as personal protective equipment. The intervention programs helped to ensure compliance and safety of the processes; all the hospitals employ the services of LAWMA for final waste disposal and treatment. Only hospital B offered on-site treatment of its waste (sharps only) with an incinerator while LAWMA uses hydroclave to treat its wastes. There are no policies or guidelines in all investigated hospitals for managing waste. An awareness of proper waste management amongst health workers has been created in most hospitals through the initiative of LAWMA. However, hospital D still mixes municipal and hazardous wastes. The treatment of waste is generally done by LAWMA using hydroclave, to prevent environmental hazards except hospital B that treats its sharp with an incinerator. In order to enhance uniform and appropriate waste management practices in the entire State, there is need for capacity building at all levels and also policies and guidelines formulations.

Shuttle era waste management and biowaste monitoring

NASA Technical Reports Server (NTRS)

Sauer, R. L.; Fogal, G. L.

1976-01-01

The acquisition of crew biomedical data has been an important task on manned space missions. The monitoring of biowastes from the crew to support water and mineral balance studies and endocrine studies has been a valuable part of this activity. This paper will present a review of waste management systems used in past programs. This past experience will be cited as to its influence on the Shuttle design. Finally, the Shuttle baseline waste management system and the proposed Shuttle biomedical measurement and sampling systems will be presented.

Solid waste containing persistent organic pollutants in Serbia: From precautionary measures to the final treatment (case study).

PubMed

Stevanovic-Carapina, Hristina; Milic, Jelena; Curcic, Marijana; Randjelovic, Jasminka; Krinulovic, Katarina; Jovovic, Aleksandar; Brnjas, Zvonko

2016-07-01

Sustainable solid waste management needs more dedicated attention in respect of environmental and human health protection. Solid waste containing persistent organic pollutants is of special concern, since persistent organic pollutants are persistent, toxic and of high risk to human health and the environment. The objective of this investigation was to identify critical points in the Serbian system of solid waste and persistent organic pollutants management, to assure the life cycle management of persistent organic pollutants and products containing these chemicals, including prevention and final destruction. Data were collected from the Serbian competent authorities, and led us to identify preventive actions for solid waste management that should reduce or minimise release of persistent organic pollutants into the environment, and to propose actions necessary for persistent organic pollutants solid waste. The adverse impact of persistent organic pollutants is multidimensional. Owing to the lack of treatment or disposal plants for hazardous waste in Serbia, the only option at the moment to manage persistent organic pollutants waste is to keep it in temporary storage and when conditions are created (primarily financial), such waste should be exported for destruction in hazardous waste incinerators. Meanwhile, it needs to be assured that any persistent organic pollutants management activity does not negatively impact recycling flows or disturb progress towards a more circular economy in Serbia. © The Author(s) 2016.

An analysis of household waste management policy using system dynamics modelling.

PubMed

Inghels, Dirk; Dullaert, Wout

2011-04-01

This paper analyses the Flemish household waste management policy. Based on historical data from the period 1991-2006, literature reviews and interviews, both mathematical and descriptive relationships are derived that describe Flemish waste collection, reuse, recycling and disposal behaviour. This provides insights into how gross domestic product (GDP), population and selective collection behaviour have influenced household waste production and collection over time. These relationships are used to model the dynamic relationships underlying household waste management in Flanders by using a system dynamics (SD) modelling approach. Where most SD models in literature are conceptual and descriptive, in the present study a real-life case with both correlational and descriptive relationships was modelled for Flanders, a European region with an outstanding waste management track record. This model was used to evaluate the current Flemish household waste management policy based on the principles of the waste hierarchy, also referred as the Lansink ranking. The results show that Flemish household waste targets up to 2015 can be achieved by the current waste policy measures. It also shows the sensitivity of some key policy parameters such as prevention and reuse. Given the general nature of the model and its limited data requirements, the authors believe that the approach implemented in this model can also assist waste policy makers in other regions or countries to meet their policy targets by simulating the effect of their current and potential household waste policy measures.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, Darrell; Poinssot, Christophe; Begg, Bruce

Management of nuclear waste remains an important international topic that includes reprocessing of commercial nuclear fuel, waste-form design and development, storage and disposal packaging, the process of repository site selection, system design, and performance assessment. Requirements to manage and dispose of materials from the production of nuclear weapons, and the renewed interest in nuclear power, in particular through the Generation IV Forum and the Advanced Fuel Cycle Initiative, can be expected to increase the need for scientific advances in waste management. A broad range of scientific and engineering disciplines is necessary to provide safe and effective solutions and address complexmore » issues. This volume offers an interdisciplinary perspective on materials-related issues associated with nuclear waste management programs. Invited and contributed papers cover a wide range of topics including studies on: spent fuel; performance assessment and models; waste forms for low- and intermediate-level waste; ceramic and glass waste forms for plutonium and high-level waste; radionuclides; containers and engineered barriers; disposal environments and site characteristics; and partitioning and transmutation.« less

Media Choice in Environmental Information Dissemination for Solid Waste Management among Policy Formulators and Implementors: A Case Study of Oyo State, Nigeria

ERIC Educational Resources Information Center

Akintola, B. A.; Temowo, O. O.; Ajiboye, J. O.

2009-01-01

Environmental information has been described as central to the issues of solid waste management and disposal. This study investigated the availability and accessibility of environmental information to the solid waste policy formulators and implementors with regard to the media/channels used for disseminating environmental information to the…

Waste Generation Overview, Course 23263

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simpson, Lewis Edward

This course, Waste Generation Overview Live (COURSE 23263), provides an overview of federal and state waste management regulations, as well as Los Alamos National Laboratory (LANL) policies and procedures for waste management operations. The course covers the activities involved in the cradle-to-grave waste management process and focuses on waste characterization, waste compatibility determinations and classification, and the storage requirements for temporary waste accumulation areas at LANL. When you have completed this course, you will be able to recognize federal, state, and LANL environmental requirements and their impact on waste operations; recognize the importance of the cradle-to-grave waste management process; identifymore » the roles and responsibilities of key LANL waste management personnel (e.g., Waste Generator, Waste Management Coordinator, Waste Stream Profile approver, and Waste Certification Official); characterize a waste stream to determine whether it meets the definition of a hazardous waste, as well as characterize the use and minimum requirements for use of acceptable knowledge (AK) for waste characterization and waste compatibility documentation requirements; and identify the requirements for setting up and managing temporary waste accumulation areas.« less

Life cycle inventory and mass-balance of municipal food waste management systems: Decision support methods beyond the waste hierarchy.

PubMed

Edwards, Joel; Othman, Maazuza; Crossin, Enda; Burn, Stewart

2017-11-01

When assessing the environmental and human health impact of a municipal food waste (FW) management system waste managers typically rely on the principles of the waste hierarchy; using metrics such as the mass or rate of waste that is 'prepared for recycling,' 'recovered for energy,' or 'sent to landfill.' These metrics measure the collection and sorting efficiency of a waste system but are incapable of determining the efficiency of a system to turn waste into a valuable resource. In this study a life cycle approach was employed using a system boundary that includes the entire waste service provision from collection to safe end-use or disposal. A life cycle inventory of seven waste management systems was calculated, including the first service wide inventory of FW management through kitchen in-sink disposal (food waste disposer). Results describe the mass, energy and water balance of each system along with key emissions profile. It was demonstrated that the energy balance can differ significantly from its' energy generation, exemplified by mechanical biological treatment, which was the best system for generating energy from waste but only 5 th best for net-energy generation. Furthermore, the energy balance of kitchen in-sink disposal was shown to be reduced because 31% of volatile solids were lost in pre-treatment. The study also confirmed that higher FW landfill diversion rates were critical for reducing many harmful emissions to air and water. Although, mass-balance analysis showed that the alternative end-use of the FW material may still contain high impact pollutants. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Greenhouse gas emission mitigation relevant to changes in municipal solid waste management system.

PubMed

Pikoń, Krzysztof; Gaska, Krzysztof

2010-07-01

Standard methods for assessing the environmental impact of waste management systems are needed to underpin the development and implementation of sustainable waste management practice. Life cycle assessment (LCA) is a tool for comprehensively ensuring such assessment and covers all impacts associated with waste management. LCA is often called "from cradle to grave" analysis. This paper integrates information on the greenhouse gas (GHG) implications of various management options for some of the most common materials in municipal solid waste (MSW). Different waste treatment options for MSW were studied in a system analysis. Different combinations of recycling (cardboard, plastics, glass, metals), biological treatment (composting), and incineration as well as land-filling were studied. The index of environmental burden in the global warming impact category was calculated. The calculations are based on LCA methodology. All emissions taking place in the whole life cycle system were taken into account. The analysis included "own emissions," or emissions from the system at all stages of the life cycle, and "linked emissions," or emissions from other sources linked with the system in an indirect way. Avoided emissions caused by recycling and energy recovery were included in the analysis. Displaced emissions of GHGs originate from the substitution of energy or materials derived from waste for alternative sources. The complex analysis of the environmental impact of municipal waste management systems before and after application of changes in MSW systems according to European Union regulations is presented in this paper. The evaluation is made for MSW systems in Poland.

Public concerns and behaviours towards solid waste management in Italy.

PubMed

Sessa, Alessandra; Di Giuseppe, Gabriella; Marinelli, Paolo; Angelillo, Italo F

2010-12-01

A self-administered questionnaire investigated knowledge, perceptions of the risks to health associated with solid waste management, and practices about waste management in a random sample of 1181 adults in Italy. Perceived risk of developing cancer due to solid waste burning was significantly higher in females, younger, with an educational level lower than university and who believed that improper waste management is linked to cancer. Respondents who had visited a physician at least once in the last year for fear of contracting a disease due to the non-correct waste management had an educational level lower than university, have modified dietary habits for fear of contracting disease due to improper waste management, believe that improper waste management is linked to allergies, perceive a higher risk of contracting infectious disease due to improper waste management and have participated in education/information activities on waste management. Those who more frequently perform with regularity differentiate household waste collection had a university educational level, perceived a higher risk of developing cancer due to solid waste burning, had received information about waste collection and did not need information about waste management. Educational programmes are needed to modify public concern about adverse health effects of domestic waste.

Exploring the Awareness Regarding E-waste and its Health Hazards among the Informal Handlers in Musheerabad Area of Hyderabad.

PubMed

Mishra, Sapna; Shamanna, B R; Kannan, Srinivasan

2017-01-01

Occupational Health hazards of handling and management of electronic waste is a nascent subject. Improper and unscientific handling of e-waste can invite significant human and environmental health risks. To study the level of awareness about electronic waste and its health hazards amongst informal handlers in Musheerabad, Hyderabad. Ethical approval and informed consents were obtained from Institutional Ethical Committee, University of Hyderabad and from the participants respectively before the commencement of study. This was a descriptive cross-sectional study conducted in randomly selected twenty-six waste handling centers from sixty of them in the locality. From each of the centers four handlers agedbetween 18 and 45 were randomly selected. Total of 104 handlers were interviewed using semi-structured schedule. Interviews were also conducted among 10 owners of such centres on the waste management practices. About 72% of the handlers did not know the meaning of electronic waste and 71% were not aware of associated health risks, 85% did not use any protective gears, while 16% acknowledged health issues attributed to improper handling of e-waste, 77% felt their handling of e-waste was appropriate. Majority of center owners felt that informal e-waste handling does not pose any health risks, and reported that there was no awareness campaign by any agency as of then. This study highlights the need for awareness campaigns on proper e-waste management practices to ensure occupational safety among the waste handlers who belong to lower socio-economic strata.

A system dynamics approach for healthcare waste management: a case study in Istanbul Metropolitan City, Turkey.

PubMed

Ciplak, Nesli; Barton, John R

2012-06-01

Healthcare waste consists of various types of waste materials generated at hospitals, medical research centres, clinics and laboratories. Although 75-90% of this waste is classified as 'domestic' in nature, 20-25% is deemed to be hazardous, which if not disposed of appropriately, poses a risk to healthcare workers, patients, the environment and even the whole community. As long as healthcare waste is mixed with municipal waste and not segregated prior to disposal, costs will increase substantially. In this study, healthcare waste increases along with the potential to decrease the amounts by implementing effective segregation at healthcare facilities are projected to 2040. Our long-term aim is to develop a system to support selection and planning of the future treatment capacity. Istanbul in Turkey was used as the case study area. In order to identify the factors affecting healthcare waste generation in Istanbul, observations were made and interviews conducted in Istanbul over a 3 month period. A system dynamics approach was adopted to build a healthcare waste management model using a software package, Vensim Ple Plus. Based on reported analysis, the non-hazardous municipal fraction co-disposed with healthcare waste is around 65%. Using the projected waste generation flows, reducing a municipal fraction to 30% has the potential to avoid some 8000 t year(-1) of healthcare waste by 2025 and almost 10 000 t year(-1) by 2035. Furthermore, if segregation practices ensured healthcare waste requiring incineration was also selectively managed, 77% of healthcare waste could be diverted to alternative treatment technologies. As the throughput capacity of the only existing healthcare waste treatment facility in Istanbul, Kemerburgaz Incinerator, has already been exceeded, it is evident that improved management could not only reduce overall flows and costs but also permit alternative and cheaper treatment systems (e.g. autoclaving) to be adopted for the healthcare waste.

Domestic waste disposal practice and perceptions of private sector waste management in urban Accra

PubMed Central

2014-01-01

Background Waste poses a threat to public health and the environment if it is not stored, collected, and disposed of properly. The perception of waste as an unwanted material with no intrinsic value has dominated attitudes towards disposal. This study investigates the domestic waste practices, waste disposal, and perceptions about waste and health in an urban community. Methods The study utilised a mixed-method approach. A cross-sectional survey questionnaire and in-depth interview were used to collect data. A total of 364 household heads were interviewed in the survey and six key informants were interviewed with the in-depth interviews. Results The results of the study revealed that 93.1% of households disposed of food debris as waste and 77.8% disposed of plastic materials as waste. The study also showed that 61.0% of the households disposed of their waste at community bins or had waste picked up at their homes by private contractors. The remaining 39.0% disposed of their waste in gutters, streets, holes and nearby bushes. Of those who paid for the services of private contractors, 62.9% were not satisfied with the services because of their cost and irregular collection. About 83% of the respondents were aware that improper waste management contributes to disease causation; most of the respondents thought that improper waste management could lead to malaria and diarrhoea. There was a general perception that children should be responsible for transporting waste from the households to dumping sites. Conclusion Proper education of the public, the provision of more communal trash bins, and the collection of waste by private contractors could help prevent exposing the public in municipalities to diseases. PMID:25005728

Domestic waste disposal practice and perceptions of private sector waste management in urban Accra.

PubMed

Yoada, Ramatta Massa; Chirawurah, Dennis; Adongo, Philip Baba

2014-07-08

Waste poses a threat to public health and the environment if it is not stored, collected, and disposed of properly. The perception of waste as an unwanted material with no intrinsic value has dominated attitudes towards disposal. This study investigates the domestic waste practices, waste disposal, and perceptions about waste and health in an urban community. The study utilised a mixed-method approach. A cross-sectional survey questionnaire and in-depth interview were used to collect data. A total of 364 household heads were interviewed in the survey and six key informants were interviewed with the in-depth interviews. The results of the study revealed that 93.1% of households disposed of food debris as waste and 77.8% disposed of plastic materials as waste. The study also showed that 61.0% of the households disposed of their waste at community bins or had waste picked up at their homes by private contractors. The remaining 39.0% disposed of their waste in gutters, streets, holes and nearby bushes. Of those who paid for the services of private contractors, 62.9% were not satisfied with the services because of their cost and irregular collection. About 83% of the respondents were aware that improper waste management contributes to disease causation; most of the respondents thought that improper waste management could lead to malaria and diarrhoea. There was a general perception that children should be responsible for transporting waste from the households to dumping sites. Proper education of the public, the provision of more communal trash bins, and the collection of waste by private contractors could help prevent exposing the public in municipalities to diseases.

Analysis of waste management issues arising from a field study evaluating decontamination of a biological agent from a building.

PubMed

Lemieux, P; Wood, J; Drake, J; Minamyer, S; Silvestri, E; Yund, C; Nichols, T; Ierardi, M; Amidan, B

2016-01-01

The Bio-response Operational Testing and Evaluation (BOTE) Project was a cross-government effort designed to operationally test and evaluate a response to a biological incident (release of Bacillus anthracis [Ba] spores, the causative agent for anthrax) from initial public health and law enforcement response through environmental remediation. The BOTE Project was designed to address site remediation after the release of a Ba simulant, Bacillus atrophaeus spp. globigii (Bg), within a facility, drawing upon recent advances in the biological sampling and decontamination areas. A key component of response to a biological contamination incident is the proper management of wastes and residues, which is woven throughout all response activities. Waste is generated throughout the response and includes items like sampling media packaging materials, discarded personal protective equipment, items removed from the facility either prior to or following decontamination, aqueous waste streams, and materials generated through the application of decontamination technologies. The amount of residual contaminating agent will impact the available disposal pathways and waste management costs. Waste management is an integral part of the decontamination process and should be included through "Pre-Incident" response planning. Overall, the pH-adjusted bleach decontamination process generated the most waste from the decontamination efforts, and fumigation with chlorine dioxide generated the least waste. A majority of the solid waste generated during pH-adjusted bleach decontamination was the nonporous surfaces that were removed, bagged, decontaminated ex situ, and treated as waste. The waste during the two fumigation rounds of the BOTE Project was associated mainly with sampling activities. Waste management activities may represent a significant contribution to the overall cost of the response/recovery operation. This paper addresses the waste management activities for the BOTE field test. Management of waste is a critical element of activities dealing with remediation of buildings and outdoor areas following a biological contamination incident. Waste management must be integrated into the overall remediation process, along with sampling, decontamination, resource management, and other important response elements, rather than being a stand-alone activity. The results presented in this paper will provide decision makers and emergency planners at the federal/state/tribal/local level information that can be used to integrate waste management into an overall systems approach to planning and response activities.

Factors and values of willingness to pay for improved construction waste management--a perspective of Malaysian contractors.

PubMed

Begum, Rawshan Ara; Siwar, Chamhuri; Pereira, Joy Jacqueline; Jaafar, Abdul Hamid

2007-01-01

Malaysia is facing an increase in the generation of waste and of accompanying problems with the disposal of this waste. In the last two decades, extensive building and infrastructure development projects have led to an increase in the generation of construction waste material. The construction industry has a substantial impact on the environment, and its environmental effects are in direct relation to the quality and quantity of the waste it generates. This paper discusses general characteristics of the construction contractors, the contractors' willingness to pay (WTP) for improved construction waste management, determining factors which affect the amount of their willingness to pay, and suggestions and policy implications in the perspective of construction waste management in Malaysia. The data in this study is based on contractors registered with the construction industry development board (CIDB) of Malaysia. Employing the open ended contingent valuation method, the study assessed the contractors' average maximum WTP for improved construction waste management to be RM69.88 (1US$=3.6 RM) per tonne of waste. The result shows that the average maximum WTP is higher for large contractors than for medium and small contractors. The highest average maximum WTP value is RM88.00 for Group A (large contractors) RM78.25 for Group B (medium-size contractors) and RM55.80 for Group C (small contractors). One of the contributions of this study is to highlight the difference of CIDB registration grade in the WTP for improved construction waste management. It is found that contractors' WTP for improved waste collection and disposal services increases with the increase in contractors' current paid up capital. The identified factors and determinants of the WTP will assist the formulation of appropriate policies in addressing the construction waste problem in Malaysia and indirectly improve the quality of construction in the country.

Municipal solid waste management in Tehran: Changes during the last 5 years.

PubMed

Malmir, Tahereh; Tojo, Yasumasa

2016-05-01

The situation of waste management in Tehran was a typical example of it in developing countries. The amount of municipal solid waste has been increasing and the city has depended on landfill for municipal solid waste management. However, in recent years, various measures have been taken by the city, such as collecting recyclables at the source and increasing the capacity of waste-processing facilities. As a result, significant changes in the waste stream are starting to occur. This study investigated the nature of, and reasons for, the marked changes in the waste stream from 2008 to 2012 by analysing the municipal solid waste statistics published by the Tehran Waste Management Organization in 2013 and survey data on the physical composition of the municipal solid waste. The following trends were identified: Although the generation of municipal solid waste increased by 10% during the 5-year period, the amount of waste directly disposed of to landfill halved and resource recovery almost doubled. An increase in the capacity of a waste-processing facility contributed significantly to these changes. The biodegradable fraction going to landfill was estimated by using the quantity and the composition of each input to the landfill. The estimated result in 2012 decreased to 49% of its value in 2008. © The Author(s) 2016.

Framework for integration of informal waste management sector with the formal sector in Pakistan.

PubMed

Masood, Maryam; Barlow, Claire Y

2013-10-01

Historically, waste pickers around the globe have utilised urban solid waste as a principal source of livelihood. Formal waste management sectors usually perceive the informal waste collection/recycling networks as backward, unhygienic and generally incompatible with modern waste management systems. It is proposed here that through careful planning and administration, these seemingly troublesome informal networks can be integrated into formal waste management systems in developing countries, providing mutual benefits. A theoretical framework for integration based on a case study in Lahore, Pakistan, is presented. The proposed solution suggests that the municipal authority should draw up and agree on a formal work contract with the group of waste pickers already operating in the area. The proposed system is assessed using the integration radar framework to classify and analyse possible intervention points between the sectors. The integration of the informal waste workers with the formal waste management sector is not a one dimensional or single step process. An ideal solution might aim for a balanced focus on all four categories of intervention, although this may be influenced by local conditions. Not all the positive benefits will be immediately apparent, but it is expected that as the acceptance of such projects increases over time, the informal recycling economy will financially supplement the formal system in many ways.

Understanding the role of waste prevention in local waste management: A literature review.

PubMed

Zacho, Kristina O; Mosgaard, Mette A

2016-10-01

Local waste management has so far been characterised by end-of-pipe solutions, landfilling, incineration, and recycling. End-of-pipe solutions build on a different mind-set than life cycle-based approaches, and for this reason, local waste managers are reluctant to consider strategies for waste prevention. To accelerate the transition of waste and resource management towards a more integrated management, waste prevention needs to play a larger role in the local waste management. In this review article, we collect knowledge from the scientific community on waste prevention of relevance to local waste management. We analyse the trends in the waste prevention literature by organising the literature into four categories. The results indicate an increasing interest in waste prevention, but not much literature specifically concerns the integration of prevention into the local waste management. However, evidence from the literature can inform local waste management on the prevention potential; the environmental and social effects of prevention; how individuals in households can be motivated to reduce waste; and how the effects of prevention measures can be monitored. Nevertheless, knowledge is still lacking on local waste prevention, especially regarding the methods for monitoring and how local waste management systems can be designed to encourage waste reduction in the households. We end the article with recommendations for future research. The literature review can be useful for both practitioners in the waste sector and for academics seeking an overview of previous research on waste prevention. © The Author(s) 2016.

Sustainable Materials Management (SMM) - Materials and Waste Management in the United States Key Facts and Figures

EPA Pesticide Factsheets

Each year EPA produces a report called Advancing Sustainable Materials Management: Facts and Figures. It includes information on municipal solid waste (MSW) generation, recycling, composting, combustion with energy recovery and landfilling. The 2014 report provides information on historical tipping fees for MSW, and information on the construction and demolition debris generation, which is outside of the scope of MSW. The Facts and Figures website includes recent reports (2012 to 2014 as well as historical information on materials in the U.S. Municipal Waste Stream, 1960 to 2014 (in tons). The reports for both current and historical waste prevention can be accessed at EPA's SMM website. The recent Annual Facts and Figures reports are accessible at the following link: https://www.epa.gov/smm/advancing-sustainable-materials-management-facts-and-figures-report. Historical data as well as studies and summary tables related to the Advancing Sustainable Materials Management Report are accessible here: https://www.epa.gov/smm/studies-summary-tables-and-data-related-advancing-sustainable-materials-management-report. An excel file containing the data from 1960 - 2014 is located here: https://edg.epa.gov/data/PUBLIC/OLEM/Materials_Municipal_Waste_Stream_1960_to_2014.xlsx. EPA also maintains a list of state and local waste characterization studies (reports are not available for all states). You can search for your state at https://www.epa.gov/smm/advancing-

High-level waste program progress report, April 1, 1980-June 30, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1980-08-01

The highlights of this report are on: waste management analysis for nuclear fuel cycles; fixation of waste in concrete; study of ceramic and cermet waste forms; alternative high-level waste forms development; and high-level waste container development.

Medical waste management training for healthcare managers - a necessity?

PubMed

Ozder, Aclan; Teker, Bahri; Eker, Hasan Huseyin; Altındis, Selma; Kocaakman, Merve; Karabay, Oguz

2013-07-16

This is an interventional study, since a training has been given, performed in order to investigate whether training has significant impact on knowledge levels of healthcare managers (head-nurses, assistant head nurses, hospital managers and deputy managers) regarding bio-medical waste management. The study was conducted on 240 volunteers during June - August 2010 in 12 hospitals serving in Istanbul (private, public, university, training-research hospitals and other healthcare institutions). A survey form prepared by the project guidance team was applied to the participants through the internet before and after the training courses. The training program was composed of 40 hours of theory and 16 hours of practice sessions taught by persons known to have expertise in their fields. Methods used in the analysis of the data chi-square and t-tests in dependent groups. 67.5% (162) of participants were female. 42.5% (102) are working in private, and 21.7% in state-owned hospitals. 50.4% are head-nurses, and 18.3% are hospital managers.A statistically significant difference was found among those who had received medical waste management training (preliminary test and final test) and others who had not (p<0.01). It was observed that information levels of all healthcare managers who had received training on waste management had risen at the completion of that training session. On the subject of waste management, to have trained healthcare employees who are responsible for the safe disposal of wastes in hospitals is both a necessity for the safety of patients and important for its contribution to the economy of the country.

Pattern of medical waste management: existing scenario in Dhaka City, Bangladesh

PubMed Central

Hassan, M Manzurul; Ahmed, Shafiul Azam; Rahman, K Anisur; Biswas, Tarit Kanti

2008-01-01

Background Medical waste is infectious and hazardous. It poses serious threats to environmental health and requires specific treatment and management prior to its final disposal. The problem is growing with an ever-increasing number of hospitals, clinics, and diagnostic laboratories in Dhaka City, Bangladesh. However, research on this critical issue has been very limited, and there is a serious dearth of information for planning. This paper seeks to document the handling practice of waste (e.g. collection, storage, transportation and disposal) along with the types and amount of wastes generated by Health Care Establishments (HCE). A total of 60 out of the existing 68 HCE in the study areas provided us with relevant information. Methods The methodology for this paper includes empirical field observation and field-level data collection through inventory, questionnaire survey and formal and informal interviews. A structured questionnaire was designed to collect information addressing the generation of different medical wastes according to amount and sources from different HCE. A number of in-depth interviews were arranged to enhance our understanding of previous and existing management practice of medical wastes. A number of specific questions were asked of nurses, hospital managers, doctors, and cleaners to elicit their knowledge. The collected data with the questionnaire survey were analysed, mainly with simple descriptive statistics; while the qualitative mode of analysis is mainly in narrative form. Results The paper shows that the surveyed HCE generate a total of 5,562 kg/day of wastes, of which about 77.4 per cent are non-hazardous and about 22.6 per cent are hazardous. The average waste generation rate for the surveyed HCE is 1.9 kg/bed/day or 0.5 kg/patient/day. The study reveals that there is no proper, systematic management of medical waste except in a few private HCE that segregate their infectious wastes. Some cleaners were found to salvage used sharps, saline bags, blood bags and test tubes for resale or reuse. Conclusion The paper reveals that lack of awareness, appropriate policy and laws, and willingness are responsible for the improper management of medical waste in Dhaka City. The paper also shows that a newly designed medical waste management system currently serves a limited number of HCE. New facilities should be established for the complete management of medical waste in Dhaka City. PMID:18221548

40 CFR 60.2620 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What is a waste management plan? 60... Commercial and Industrial Solid Waste Incineration Units that Commenced Construction On or Before November 30, 1999 Model Rule-Waste Management Plan § 60.2620 What is a waste management plan? A waste management...

40 CFR 60.3010 - What is a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false What is a waste management plan? 60... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Waste Management Plan § 60.3010 What is a waste management plan? A waste management plan is a...

40 CFR 60.2620 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What is a waste management plan? 60... Commercial and Industrial Solid Waste Incineration Units Model Rule-Waste Management Plan § 60.2620 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility...

40 CFR 60.3010 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What is a waste management plan? 60... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Waste Management Plan § 60.3010 What is a waste management plan? A waste management plan is a...

40 CFR 60.3010 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What is a waste management plan? 60... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Waste Management Plan § 60.3010 What is a waste management plan? A waste management plan is a...

40 CFR 60.3010 - What is a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false What is a waste management plan? 60... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Waste Management Plan § 60.3010 What is a waste management plan? A waste management plan is a...

45 CFR 671.13 - Waste management for the USAP.

Code of Federal Regulations, 2014 CFR

2014-10-01

... can be taken into account in planning future scientific, logistic and waste management programs. (e... 45 Public Welfare 3 2014-10-01 2014-10-01 false Waste management for the USAP. 671.13 Section 671... WASTE REGULATION Waste Management § 671.13 Waste management for the USAP. (a) In order to provide a...

45 CFR 671.13 - Waste management for the USAP.

Code of Federal Regulations, 2013 CFR

2013-10-01

... can be taken into account in planning future scientific, logistic and waste management programs. (e... 45 Public Welfare 3 2013-10-01 2013-10-01 false Waste management for the USAP. 671.13 Section 671... WASTE REGULATION Waste Management § 671.13 Waste management for the USAP. (a) In order to provide a...

45 CFR 671.13 - Waste management for the USAP.

Code of Federal Regulations, 2012 CFR

2012-10-01

... can be taken into account in planning future scientific, logistic and waste management programs. (e... 45 Public Welfare 3 2012-10-01 2012-10-01 false Waste management for the USAP. 671.13 Section 671... WASTE REGULATION Waste Management § 671.13 Waste management for the USAP. (a) In order to provide a...

45 CFR 671.13 - Waste management for the USAP.

Code of Federal Regulations, 2010 CFR

2010-10-01

... can be taken into account in planning future scientific, logistic and waste management programs. (e... 45 Public Welfare 3 2010-10-01 2010-10-01 false Waste management for the USAP. 671.13 Section 671... WASTE REGULATION Waste Management § 671.13 Waste management for the USAP. (a) In order to provide a...

Practices, Concerns, and Willingness to Participate in Solid Waste Management in Two Urban Slums in Central Uganda

PubMed Central

Ndejjo, Rawlance; Musoke, David; Musinguzi, Geofrey; Halage, Abdullah Ali; Carpenter, David O.; Ssempebwa, John C.

2016-01-01

Poor solid waste management is among the major challenges facing urban slums in developing countries including Uganda. Understanding community concerns and willingness towards involvement in solid waste management improvement initiatives is critical for informing interventions in slums. Methods. We used a cross-sectional study to collect quantitative data from 435 residents in two urban slums in central Uganda. A semistructured questionnaire was used which assessed waste collection practices, separation and disposal methods, concerns regarding solid wastes, and willingness to participate in waste separation and composting. Data was analysed using STATA 12. Results. Food remains (38%) and plastics (37%) formed the biggest proportion of wastes generated in households. Most households (35.9%) disposed of general wastes by open dumping while 27% disposed of plastics by burning. Only 8.8% of households conducted composting while 55% carried out separation for some decomposable wastes. Separation was carried out for only banana peelings and leftover foods for feeding animals. Respondents expressed high willingness to separate (76.6%) and compost (54.9%) solid wastes. Conclusion. Practices in waste disposal and separation were poor despite high willingness to participate in initiatives to improve waste management, highlighting a need for authorities to engage residents of slums to improve their practices. PMID:27066081

Practices, Concerns, and Willingness to Participate in Solid Waste Management in Two Urban Slums in Central Uganda.

PubMed

Mukama, Trasias; Ndejjo, Rawlance; Musoke, David; Musinguzi, Geofrey; Halage, Abdullah Ali; Carpenter, David O; Ssempebwa, John C

2016-01-01

Poor solid waste management is among the major challenges facing urban slums in developing countries including Uganda. Understanding community concerns and willingness towards involvement in solid waste management improvement initiatives is critical for informing interventions in slums. We used a cross-sectional study to collect quantitative data from 435 residents in two urban slums in central Uganda. A semistructured questionnaire was used which assessed waste collection practices, separation and disposal methods, concerns regarding solid wastes, and willingness to participate in waste separation and composting. Data was analysed using STATA 12. Food remains (38%) and plastics (37%) formed the biggest proportion of wastes generated in households. Most households (35.9%) disposed of general wastes by open dumping while 27% disposed of plastics by burning. Only 8.8% of households conducted composting while 55% carried out separation for some decomposable wastes. Separation was carried out for only banana peelings and leftover foods for feeding animals. Respondents expressed high willingness to separate (76.6%) and compost (54.9%) solid wastes. Practices in waste disposal and separation were poor despite high willingness to participate in initiatives to improve waste management, highlighting a need for authorities to engage residents of slums to improve their practices.

Municipal solid waste generation and disposal in Robe town, Ethiopia.

PubMed

Erasu, Duguma; Faye, Tesfaye; Kiros, Amaha; Balew, Abel

2018-04-20

The amount of solid waste generated in developing countries is rising from time to time due to economic growth, change in consumer behavior and lifestyles of people. But it is hard to manage and handle the increase of solid waste with existing waste management infrastructure. Thus, the management system of solid waste is very poor and become a serious problem. The main purpose of this study is to quantify the volume of solid waste generated and investigate factors affecting generation and disposal of wastes in the study area. The result of this study indicated that total waste generated from households was about 97.092kg/day.Furthermore, the study reveals that the solid waste generation rate of the town is 0.261kg/person/day.About 57.5% of solid waste is properly disposed of to landfill site whereas the remaining 42.5% is illegally dumped at the roadsides and open fields. Implication Statement Nowadays, in developing countries there is high concentration of people in urban areas and cause for the generation of enormous concentration of municipal waste in urban areas. Therefore this finding will be important for various policy makers and town planners. It may also serve as a benchmark for the municipal authorities of the town for whom the problem is still invisible and negligible and can push environmental protection authorities to reexamine the implementation of their policies and strategies with regard to the broader issues of human and environmental health condition of town dwellers.

Hospital solid waste management practices in Limpopo Province, South Africa: A case study of two hospitals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemathaga, Felicia; Maringa, Sally; Chimuka, Luke

2008-07-01

The shortcomings in the management practices of hospital solid waste in Limpopo Province of South Africa were studied by looking at two hospitals as case studies. Apart from field surveys, the generated hospital waste was weighed to compute the generation rates and was followed through various management practices to the final disposal. The findings revealed a major policy implementation gap between the national government and the hospitals. While modern practices such as landfill and incineration are used, their daily operations were not carried according to minimum standards. Incinerator ash is openly dumped and wastes are burned on landfills instead ofmore » being covered with soil. The incinerators used are also not environmentally friendly as they use old technology. The findings further revealed that there is no proper separation of wastes according to their classification as demanded by the national government. The mean percentage composition of the waste was found in the following decreasing order: general waste (60.74%) > medical waste (30.32%) > sharps (8.94%). The mean generation rates were found to be 0.60 kg per patient per day.« less

Sustainable solutions for solid waste management in Southeast Asian countries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uyen Nguyen Ngoc; Schnitzer, Hans

2009-06-15

Human activities generate waste and the amounts tend to increase as the demand for quality of life increases. Today's rate in the Southeast Asian Nations (ASEANs) is alarming, posing a challenge to governments regarding environmental pollution in the recent years. The expectation is that eventually waste treatment and waste prevention approaches will develop towards sustainable waste management solutions. This expectation is for instance reflected in the term 'zero emission systems'. The concept of zero emissions can be applied successfully with today's technical possibilities in the agro-based processing industry. First, the state-of-the-art of waste management in Southeast Asian countries will bemore » outlined in this paper, followed by waste generation rates, sources, and composition, as well as future trends of waste. Further on, solutions for solid waste management will be reviewed in the discussions of sustainable waste management. The paper emphasizes the concept of waste prevention through utilization of all wastes as process inputs, leading to the possibility of creating an ecosystem in a loop of materials. Also, a case study, focusing on the citrus processing industry, is displayed to illustrate the application of the aggregated material input-output model in a widespread processing industry in ASEAN. The model can be shown as a closed cluster, which permits an identification of opportunities for reducing environmental impacts at the process level in the food processing industry. Throughout the discussion in this paper, the utilization of renewable energy and economic aspects are considered to adapt to environmental and economic issues and the aim of eco-efficiency. Additionally, the opportunities and constraints of waste management will be discussed.« less

Removal of radioactive contaminants by polymeric microspheres.

PubMed

Osmanlioglu, Ahmet Erdal

2016-11-01

Radionuclide removal from radioactive liquid waste by adsorption on polymeric microspheres is the latest application of polymers in waste management. Polymeric microspheres have significant immobilization capacity for ionic substances. A laboratory study was carried out by using poly(N-isopropylacrylamide) for encapsulation of radionuclide in the liquid radioactive waste. There are numbers of advantages to use an encapsulation technology in radioactive waste management. Results show that polymerization step of radionuclide increases integrity of solidified waste form. Test results showed that adding the appropriate polymer into the liquid waste at an appropriate pH and temperature level, radionuclide was encapsulated into polymer. This technology may provide barriers between hazardous radioactive ions and the environment. By this method, solidification techniques became easier and safer in nuclear waste management. By using polymer microspheres as dust form, contamination risks were decreased in the nuclear industry and radioactive waste operations.

40 CFR 260.23 - Petitions to amend 40 CFR part 273 to include additional hazardous wastes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking... appropriate for the waste or category of waste; will improve management practices for the waste or category of... waste or category of waste, will improve management practices for the waste or category of waste, and...

40 CFR 260.23 - Petitions to amend 40 CFR part 273 to include additional hazardous wastes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking... appropriate for the waste or category of waste; will improve management practices for the waste or category of... waste or category of waste, will improve management practices for the waste or category of waste, and...

40 CFR 260.23 - Petitions to amend 40 CFR part 273 to include additional hazardous wastes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking... appropriate for the waste or category of waste; will improve management practices for the waste or category of... waste or category of waste, will improve management practices for the waste or category of waste, and...

40 CFR 260.23 - Petitions to amend 40 CFR part 273 to include additional hazardous wastes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking... appropriate for the waste or category of waste; will improve management practices for the waste or category of... waste or category of waste, will improve management practices for the waste or category of waste, and...

The analysis of waste treatment methods and managerial skills towards the effectiveness of CO2 emmissions (an ex post facto study at TPA Bantar Gebang Bekasi)

NASA Astrophysics Data System (ADS)

Ria Rajagukguk, Jenni; Siagian, Lestina

2017-09-01

In the last three years, Java Island produces 29.413.336 m3/year of waste, coming from settlement (house hold) and non-settlement waste. Recently, this waste is managed with conventional technology, composting and recycling. Based on law No. 18 of 2008 on Waste Management, Chapter III Article 5, it is firmly stated that the government and regional governments are responsible for ensuring proper and environmentally sound waste management in accordance with the objectives. The observation of managerial skills is highly needed to investigate the operation of waste management at TPA Bantar Gebang towards the effectiveness of CO2 emissions.The problems are (1)Whether there is any influence between the method of waste management through Biogas Technology to the effectiveness of CO2 emissions. (2) Whether there is any influence between managerial skills to effectiveness of CO2 emission. (3) Whether there is any simultaneous influence between waste management method and managerial skill to CO2 emission effectiveness and (4) how is the method of waste management. Quantitative and egineering method were used to process the data.Biogas Technology variables and Managerial Skill are simultaneously and significantly influenced to CO2 Emission Effectiveness, this is based on Fh > Ft value of 168,453 > 3.072467) and its significance is 0.000 < 0,05. Then Ho was rejected and Ha was accepted which means that variable of Managerial Skill have influence or very big influence to Effeciveness of CO2 Emission, Correlation coefficient value 94,1% which means there is very strong relation between variable of Biogas Technology, Managerial Skill to Effectiveness of CO2 emission. Then Technology management through Biogas Technology is anaerobic biology.

A Spanish model for quantification and management of construction waste.

PubMed

Solís-Guzmán, Jaime; Marrero, Madelyn; Montes-Delgado, Maria Victoria; Ramírez-de-Arellano, Antonio

2009-09-01

Currently, construction and demolition waste (C&D waste) is a worldwide issue that concerns not only governments but also the building actors involved in construction activity. In Spain, a new national decree has been regulating the production and management of C&D waste since February 2008. The present work describes the waste management model that has inspired this decree: the Alcores model implemented with good results in Los Alcores Community (Seville, Spain). A detailed model is also provided to estimate the volume of waste that is expected to be generated on the building site. The quantification of C&D waste volume, from the project stage, is essential for the building actors to properly plan and control its disposal. This quantification model has been developed by studying 100 dwelling projects, especially their bill of quantities, and defining three coefficients to estimate the demolished volume (CT), the wreckage volume (CR) and the packaging volume (CE). Finally, two case studies are included to illustrate the usefulness of the model to estimate C&D waste volume in both new construction and demolition projects.

Investigating motivating factors for sound hospital waste management.

PubMed

Ali, Mustafa; Wang, Wenping; Chaudhry, Nawaz

2016-08-01

Sustainable management of hospital waste requires an active involvement of all key players. This study aims to test the hypothesis that three motivating factors, namely, Reputation, Liability, and Expense, influence hospital waste management. The survey for this study was conducted in two phases, with the pilot study used for exploratory factor analysis and the subsequent main survey used for cross-validation using confirmatory factor analysis. The hypotheses were validated through one-sample t tests. Correlations were established between the three motivating factors and organizational characteristics of hospital type, location, category, and size. The hypotheses were validated, and it was found that the factors of Liability and Expense varied considerably with respect to location and size of a hospital. The factor of Reputation, however, did not exhibit significant variation. In conclusion, concerns about the reputation of a facility and an apprehension of liability act as incentives for sound hospital waste management, whereas concerns about financial costs and perceived overburden on staff act as disincentives. This paper identifies the non economic motivating factors that can be used to encourage behavioral changes regarding waste management at hospitals in resource constrained environments. This study discovered that organizational characteristics such as hospital size and location cause the responses to vary among the subjects. Hence a policy maker must take into account the institutional setting before introducing a change geared towards better waste management outcomes across hospitals. This study covers a topic that has hitherto been neglected in resource constrained countries. Thus it can be used as one of the first steps to highlight and tackle the issue.

Infectious waste management in Japan: A revised regulation and a management process in medical institutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyazaki, M.; Une, H.

In Japan, the waste management practice is carried out in accordance with the Waste Disposal Law of 1970. The first rule of infectious waste management was regulated in 1992, and infectious wastes are defined as the waste materials generated in medical institutions as a result of medical care or research which contain pathogens that have the potential to transmit infectious diseases. Revised criteria for infectious waste management were promulgated by the Ministry of Environment in 2004. Infectious waste materials are divided into three categories: the form of waste; the place of waste generation; the kind of infectious diseases. A reductionmore » of infectious waste is expected. We introduce a summary of the revised regulation of infectious waste management in this article.« less

A Nuclear Waste Management Cost Model for Policy Analysis

NASA Astrophysics Data System (ADS)

Barron, R. W.; Hill, M. C.

2017-12-01

Although integrated assessments of climate change policy have frequently identified nuclear energy as a promising alternative to fossil fuels, these studies have often treated nuclear waste disposal very simply. Simple assumptions about nuclear waste are problematic because they may not be adequate to capture relevant costs and uncertainties, which could result in suboptimal policy choices. Modeling nuclear waste management costs is a cross-disciplinary, multi-scale problem that involves economic, geologic and environmental processes that operate at vastly different temporal scales. Similarly, the climate-related costs and benefits of nuclear energy are dependent on environmental sensitivity to CO2 emissions and radiation, nuclear energy's ability to offset carbon emissions, and the risk of nuclear accidents, factors which are all deeply uncertain. Alternative value systems further complicate the problem by suggesting different approaches to valuing intergenerational impacts. Effective policy assessment of nuclear energy requires an integrated approach to modeling nuclear waste management that (1) bridges disciplinary and temporal gaps, (2) supports an iterative, adaptive process that responds to evolving understandings of uncertainties, and (3) supports a broad range of value systems. This work develops the Nuclear Waste Management Cost Model (NWMCM). NWMCM provides a flexible framework for evaluating the cost of nuclear waste management across a range of technology pathways and value systems. We illustrate how NWMCM can support policy analysis by estimating how different nuclear waste disposal scenarios developed using the NWMCM framework affect the results of a recent integrated assessment study of alternative energy futures and their effects on the cost of achieving carbon abatement targets. Results suggest that the optimism reflected in previous works is fragile: Plausible nuclear waste management costs and discount rates appropriate for intergenerational cost-benefit analysis produce many scenarios where nuclear energy is economically unattractive.

40 CFR 273.52 - Waste management.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 28 2013-07-01 2013-07-01 false Waste management. 273.52 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Universal Waste Transporters § 273.52 Waste management. (a) A universal waste transporter must comply with all applicable U.S. Department of...

40 CFR 273.52 - Waste management.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 28 2012-07-01 2012-07-01 false Waste management. 273.52 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Universal Waste Transporters § 273.52 Waste management. (a) A universal waste transporter must comply with all applicable U.S. Department of...

40 CFR 273.52 - Waste management.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 27 2011-07-01 2011-07-01 false Waste management. 273.52 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Universal Waste Transporters § 273.52 Waste management. (a) A universal waste transporter must comply with all applicable U.S. Department of...

40 CFR 273.52 - Waste management.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 27 2014-07-01 2014-07-01 false Waste management. 273.52 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Universal Waste Transporters § 273.52 Waste management. (a) A universal waste transporter must comply with all applicable U.S. Department of...

40 CFR 273.52 - Waste management.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Waste management. 273.52 Section 273...) STANDARDS FOR UNIVERSAL WASTE MANAGEMENT Standards for Universal Waste Transporters § 273.52 Waste management. (a) A universal waste transporter must comply with all applicable U.S. Department of...

Concept of sustainable waste management in the city of Zagreb: Towards the implementation of circular economy approach.

PubMed

Ribić, Bojan; Voća, Neven; Ilakovac, Branka

2017-02-01

Improvement of the current waste management is one of the main challenges for most municipalities in Croatia, mainly due to legal obligations set in different European Union (EU) directives regarding waste management, such as reduction of waste generation and landfilling, or increase of separately collected waste and recycling rates. This paper highlights the current waste management in the city of Zagreb by analyzing the waste generation, collection, and disposal scenario along with the regulatory and institutional framework. Since the present waste management system mainly depends upon landfilling, with the rate of separate waste collection and recycling far from being adequate, it is necessary to introduce a new system that will take into account the current situation in the city as well as the obligations imposed by the EU. Namely, in the coming years, the Waste Framework and Landfill Directives of the European Union will be a significant driver of change in waste management practices and governance of the city of Zagreb. At present, the yearly separate waste collection makes somewhat less than 5 kg per capita of various waste fractions, i.e., far below the average value for the (28) capital cities of the EU, which is 108 kg per capita. This is possible to achieve only by better and sustainable planning of future activities and facilities, taking into account of environmental, economic, and social aspects of waste management. This means that the city of Zagreb not only will have to invest in new infrastructure to meet the targets, but also will have to enhance public awareness in diverting this waste at the household level. The solution for the new waste management proposed in this paper will certainly be a way of implementing circular economy approach to current waste management practice in the city of Zagreb. Municipal waste management in the developing countries in the EU (new eastern EU members) is often characterized by its limited utilization of recycling activities, inadequate management of nonindustrial hazardous waste, and inadequate landfill disposal. Many cities in Eastern Europe and Zagreb as well are facing serious problems in managing municipal wastes due to the existing solid waste management system that is found to be highly inefficient. The proposed scenario for city of Zagreb in the paper is an innovative upgrading of municipal waste management based on the waste management hierarchy and circular economy approach.

40 CFR 60.2625 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management... Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Waste Management Plan § 60.2625 When must I submit my waste management plan? You must submit a waste management plan no...

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false What is a waste management plan? 60... Industrial Solid Waste Incineration Units Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility and the methods used to...

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false What is a waste management plan? 60... Industrial Solid Waste Incineration Units Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility and the methods used to...

INTEGRATED MULTIMEDIA DECISION-MAKING FOR HUMAN AND ECOLOGICAL RISK ASSESSMENT: A NATIONAL-SCALE STUDY OF LAND APPLICATION OF ARSENIC-BEARING WASTES

EPA Science Inventory

Requisite to the development and application of sound waste management policies, decision-makers must discern the impact of a given waste management approach upon both human and ecological receptors. To configure such policies solely upon the assessment of impact to humans, for ...

Investigation of health care waste management in Binzhou District, China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruoyan, Gai; Xu Lingzhong; Li Huijuan

In China, national regulations and standards for health care waste management were implemented in 2003. To investigate the current status of health care waste management at different levels of health care facilities (HCF) after the implementation of these regulations, one tertiary hospital, one secondary hospital, and four primary health care centers from Binzhou District were visited and 145 medical staff members and 24 cleaning personnel were interviewed. Generated medical waste totaled 1.22, 0.77, and 1.17 kg/bed/day in tertiary, secondary, and primary HCF, respectively. The amount of medical waste generated in primary health care centers was much higher than that inmore » secondary hospitals, which may be attributed to general waste being mixed with medical waste. This study found that the level of the HCF, responsibility for medical waste management in departments and wards, educational background and training experience can be factors that determine medical staff members' knowledge of health care waste management policy. Regular training programs and sufficient provision of protective measures are urgently needed to improve occupational safety for cleaning personnel. Financing and administrative monitoring by local authorities is needed to improve handling practices and the implementation of off-site centralized disposal in primary health care centers.« less

Municipal solid waste management for total resource recycling: a case study on Haulien County in Taiwan.

PubMed

Chang, Yu-Min; Liu, Chien-Chung; Dai, Wen-Chien; Hu, Allen; Tseng, Chao-Heng; Chou, Chieh-Mei

2013-01-01

This work presents the enforcement performance of recent Haulien County, Taiwan municipal solid waste (MSW) recycling management programs. These programs include: Mandatory Refuse Sorting and Recycling, Diverse Bulk Waste Reuse, Pay-as-you-Discharge, Total Food Waste Recycling, Restricted Use on Plastic Shopping Bags & Plastic Tableware, Recycling Fund Management, and Ash Reuse. These programs provide incentives to reduce the MSW quantity growth rate. It was found that the recycled material fraction of MSW generated in 2001 was from 6.8%, but was 32.4% in 2010 and will increase stably by 2-5% yearly in the near future. Survey data for the last few years show that only 2.68% (based on total MSW generated) of food waste was collected in 2001. However, food waste was up to 9.7% in 2010 after the Total Food Waste Recycling program was implemented. The reutilization rate of bottom ash was 20% in 2005 and up to 65% in 2010 owing to Ash Reuse Program enforcement. A quantified index, the Total Recycle Index, was proposed to evaluate MSW management program performance. The demonstrated county will move toward a zero waste society in 2015 if the Total Recycle Index approaches 1.00. Exact management with available programs can lead to slow-growing waste volume and recovery of all MSW.

Analysis of post-mining excavations as places for municipal waste

NASA Astrophysics Data System (ADS)

Górniak-Zimroz, Justyna

2018-01-01

Waste management planning is an interdisciplinary task covering a wide range of issues including costs, legal requirements, spatial planning, environmental protection, geography, demographics, and techniques used in collecting, transporting, processing and disposing of waste. Designing and analyzing this issue is difficult and requires the use of advanced analysis methods and tools available in GIS geographic information systems containing readily available graphical and descriptive databases, data analysis tools providing expert decision support while selecting the best-designed alternative, and simulation models that allow the user to simulate many variants of waste management together with graphical visualization of the results of performed analyzes. As part of the research study, there have been works undertaken concerning the use of multi-criteria data analysis in waste management in areas located in southwestern Poland. These works have proposed the inclusion in waste management of post-mining excavations as places for the final or temporary collection of waste assessed in terms of their suitability with the tools available in GIS systems.

Management of plastic wastes at Brazilian ports and diagnosis of their generation.

PubMed

Neffa Gobbi, Clarice; Lourenço Sanches, Vânia Maria; Acordi Vasques Pacheco, Elen Beatriz; de Oliveira Cavalcanti Guimarães, Maria José; Vasconcelos de Freitas, Marcos Aurélio

2017-11-15

This study evaluated the management of plastic wastes at 20 Brazilian maritime ports, from three sources: vessels, leased and non-leased areas. The data were obtained from documents on port wastes organized in a relational database with defined protocols (closed form). Analysis of the spreadsheets prepared and field visits revealed that the main bottleneck in managing plastic wastes at ports is their segregation. In general, more material is segregated and sent for recycling from leased areas than non-leased ones (administered by the government). This relatively better performance in managing the wastes generated in leased areas is probably due to the need for private operators to comply with the international standards such as the Code of Environmental Practice to satisfy the international market. Copyright © 2017 Elsevier Ltd. All rights reserved.

Health Impact Assessment and Evaluation of a Clinical Waste Management Policy for Cameroon

PubMed Central

Mochungong, Peter Ikome Kuwoh

2013-01-01

Health impact assessment (HIA) was carried out to evaluate development of a clinical waste management policy for Cameroon. Fifteen stakeholders of different portfolios within the health sector were selected during a HIA initiating study trip to the Northwest region of Cameroon. Questionnaires were then developed and emailed to the stakeholders. The stakeholders identified cross-contamination, environmental pollution, physical injuries and poor waste management sites as potential risk factors that can be associated with poor clinical waste management. They recommended strong economic and political capital as a prerequisite for the development and implementation of a successful clinical waste policy. Local impacts on health, according to the stakeholders, should be prioritized in deciding any treatment and disposal option. The whole HIA process run through 2008-2010. PMID:28299096

Exploring the Awareness Regarding E-waste and its Health Hazards among the Informal Handlers in Musheerabad Area of Hyderabad

PubMed Central

Mishra, Sapna; Shamanna, B. R.; Kannan, Srinivasan

2017-01-01

Introduction: Occupational Health hazards of handling and management of electronic waste is a nascent subject. Improper and unscientific handling of e-waste can invite significant human and environmental health risks. Objective: To study the level of awareness about electronic waste and its health hazards amongst informal handlers in Musheerabad, Hyderabad. Methodology: Ethical approval and informed consents were obtained from Institutional Ethical Committee, University of Hyderabad and from the participants respectively before the commencement of study. This was a descriptive cross-sectional study conducted in randomly selected twenty-six waste handling centers from sixty of them in the locality. From each of the centers four handlers agedbetween 18 and 45 were randomly selected. Total of 104 handlers were interviewed using semi-structured schedule. Interviews were also conducted among 10 owners of such centres on the waste management practices. Results: About 72% of the handlers did not know the meaning of electronic waste and 71% were not aware of associated health risks, 85% did not use any protective gears, while 16% acknowledged health issues attributed to improper handling of e-waste, 77% felt their handling of e-waste was appropriate. Majority of center owners felt that informal e-waste handling does not pose any health risks, and reported that there was no awareness campaign by any agency as of then. Conclusion: This study highlights the need for awareness campaigns on proper e-waste management practices to ensure occupational safety among the waste handlers who belong to lower socio-economic strata. PMID:29618915

Analytical method of waste allocation in waste management systems: Concept, method and case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bergeron, Francis C., E-mail: francis.b.c@videotron.ca

Waste is not a rejected item to dispose anymore but increasingly a secondary resource to exploit, influencing waste allocation among treatment operations in a waste management (WM) system. The aim of this methodological paper is to present a new method for the assessment of the WM system, the “analytical method of the waste allocation process” (AMWAP), based on the concept of the “waste allocation process” defined as the aggregation of all processes of apportioning waste among alternative waste treatment operations inside or outside the spatial borders of a WM system. AMWAP contains a conceptual framework and an analytical approach. Themore » conceptual framework includes, firstly, a descriptive model that focuses on the description and classification of the WM system. It includes, secondly, an explanatory model that serves to explain and to predict the operation of the WM system. The analytical approach consists of a step-by-step analysis for the empirical implementation of the conceptual framework. With its multiple purposes, AMWAP provides an innovative and objective modular method to analyse a WM system which may be integrated in the framework of impact assessment methods and environmental systems analysis tools. Its originality comes from the interdisciplinary analysis of the WAP and to develop the conceptual framework. AMWAP is applied in the framework of an illustrative case study on the household WM system of Geneva (Switzerland). It demonstrates that this method provides an in-depth and contextual knowledge of WM. - Highlights: • The study presents a new analytical method based on the waste allocation process. • The method provides an in-depth and contextual knowledge of the waste management system. • The paper provides a reproducible procedure for professionals, experts and academics. • It may be integrated into impact assessment or environmental system analysis tools. • An illustrative case study is provided based on household waste management in Geneva.« less

A solid waste management survey in Davao del Sur (school and household waste management survey)

NASA Astrophysics Data System (ADS)

Trondillo, Mark Jude F.; Amaba, Jeneley A.; Paniza, Lyndelle Ann D.; Cubol, John Rhico V.

2018-02-01

Environmental degradation has become a very alarming issue at present. Human activities have been the primary cause of this unfortunate event which has resulted to other complications such as health problems. The resources are limited and people solely depend on it for living. Thus, the necessity to address these concerns arises. Various solid waste management programs have been established however the people's commitment has continued to challenge the local authorities as well as the cooperating agencies. This study was conducted in order to assess the awareness, practice and attitude towards the existing solid waste management programs of the selected students in Davao del Sur. It also aims to measure the effectiveness and current status of these implemented programs. The study used survey method. One hundred sixty eight of 227 students were surveyed using a validated, self-administered instrument. The study revealed that majority of the students is well aware of the existing solid waste management programs, practice them and is willing to learn more about the issue. Others, on the other hand, do the opposite. It is of great importance that all citizens must commit in the implementation of environmental programs so as to be more effective.

Healthcare waste management: qualitative and quantitative appraisal of nurses in a tertiary care hospital of India.

PubMed

Shivalli, Siddharudha; Sanklapur, Vasudha

2014-01-01

The nurse's role in healthcare waste management is crucial. (1) To appraise nurses quantitatively and qualitatively regarding healthcare waste management; (2) to elicit the determinants of knowledge and attitudes of healthcare waste management. A cross-sectional study was undertaken at a tertiary care hospital of Mangalore, India. Self-administered pretested questionnaire and "nonparticipatory observation" were used for quantitative and qualitative appraisals. Percentage knowledge score was calculated based on their total knowledge score. Nurses' knowledge was categorized as excellent (>70%), good (50-70%), and poor (<50%). Chi square test was applied to judge the association of study variables with their attitudes and knowledge. Out of 100 nurses 47 had excellent knowledge (>70% score). Most (86%) expressed the need of refresher training. No study variable displayed significant association (P > 0.05) with knowledge. Apt segregation practices were followed except in casualty. Patients and entourages misinterpreted the colored containers. Nurses' knowledge and healthcare waste management practices were not satisfactory. There is a need of refresher trainings at optimum intervals to ensure sustainability and further improvement. Educating patients and their entourages and display of segregation information board in local language are recommended.

Commercial treatability study capabilities for application to the US Department of Energy`s anticipated mixed waste streams. Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-09-01

US DOE mixed low-level and mixed transuranic waste inventory was estimated at 181,000 cubic meters (about 2,000 waste streams). Treatability studies may be used as part of DOE`s mixed waste management program. Commercial treatability study suppliers have been identified that either have current capability in their own facilities or have access to licensed facilities. Numerous federal and state regulations, as well as DOE Order 5820.2A, impact the performance of treatability studies. Generators, transporters, and treatability study facilities are subject to regulation. From a mixed- waste standpoint, a key requirement is that the treatability study facility must have an NRC ormore » state license that allows it to possess radioactive materials. From a RCRA perspective, the facility must support treatability study activities with the applicable plans, reports, and documentation. If PCBs are present in the waste, TSCA will also be an issue. CERCLA requirements may apply, and both DOE and NRC regulations will impact the transportation of DOE mixed waste to an off-site treatment facility. DOE waste managers will need to be cognizant of all applicable regulations as mixed-waste treatability study programs are initiated.« less

Designing and examining e-waste recycling process: methodology and case studies.

PubMed

Li, Jinhui; He, Xin; Zeng, Xianlai

2017-03-01

Increasing concerns on resource depletion and environmental pollution have largely obliged electrical and electronic waste (e-waste) should be tackled in an environmentally sound manner. Recycling process development is regarded as the most effective and fundamental to solve the e-waste problem. Based on global achievements related to e-waste recycling in the past 15 years, we first propose a theory to design an e-waste recycling process, including measuring e-waste recyclability and selection of recycling process. And we summarize the indicators and tools in terms of resource dimension, environmental dimension, and economic dimension, to examine the e-waste recycling process. Using the sophisticated experience and adequate information of e-waste management, spent lithium-ion batteries and waste printed circuit boards are chosen as case studies to implement and verify the proposed method. All the potential theory and obtained results in this work can contribute to future e-waste management toward best available techniques and best environmental practices.

Bio-Medical Waste Managment in a Tertiary Care Hospital: An Overview

PubMed Central

Ahuja, Sanjiv; Madan, Molly; Asthana, Ajay Kumar

2016-01-01

Introduction Bio-Medical Waste (BMW) management is of utmost importance as its improper management poses serious threat to health care workers, waste handlers, patients, care givers, community and finally the environment. Simultaneously, the health care providers should know the quantity of waste generated in their facility and try to reduce the waste generation in day-to-day work because lesser amount of BMW means a lesser burden on waste disposal work and cost saving. Aim To have an overview of management of BMW in a tertiary care teaching hospital so that effective interventions and implementations can be carried out for better outcome. Materials and Methods The observational study was carried out over a period of five months from January 2016 to May 2016 in Chhatrapati Shivaji Subharti Hospital, Meerut by the Infection Control Team (ICT). Assessment of knowledge was carried out by asking set of questions individually and practice regarding awareness of BMW Management among the Health Care Personnel (HCP) was carried out by direct observation in the workplace. Further, the total BMW generated from the present setup in kilogram per bed per day was calculated by dividing the mean waste generated per day by the number of occupied beds. Results Segregation of BMW was being done at the site of generation in almost all the areas of the hospital in color coded polythene bags as per the hospital protocol. The different types of waste being collected were infectious solid waste in red bag, soiled infectious waste in yellow bag and sharp waste in puncture proof container and blue bag. Though awareness (knowledge) about segregation of BMW was seen in 90% of the HCP, 30%-35% did not practice. Out of the total waste generated (57912 kg.), 8686.8 kg. (15%) was infectious waste. Average infectious waste generated was 0.341 Kg per bed per day. The transport, treatment and disposal of each collected waste were outsourced and carried out by ‘Synergy’ waste management Pvt. Ltd. Conclusion The practice of BMW Management was lacking in 30-35% HCP which may lead to mixing of the 15% infectious waste with the remaining non-infectious. Therefore, training courses and awareness programs about BMW management will be carried out every month targeting smaller groups. PMID:28050362

Effectiveness of intensive healthcare waste management training model among health professionals at teaching hospitals of Pakistan: a quasi-experimental study.

PubMed

Kumar, Ramesh; Somrongthong, Ratana; Shaikh, Babar Tasneem

2015-02-28

Infectious waste management has always remained a neglected public health problem in the developing countries, resulting in high burden of environmental pollution affecting general masses. Health workers are the key personnel who are responsible for the management of infectious waste at any hospital, however, their proper training and education is must for an optimal performance. This interventional study was conducted to assess the effectiveness of Intensive healthcare waste management (IHWM) training model at two tertiary care hospitals of Rawalpindi city, Pakistan. This study was quasi-experimental pre and post design with control and intervention groups. Out of 275 health care workers enrolled for the study, 138 workers were assigned for intervention group for 3 months trainings, hands-on practicum and reminders on infectious waste management; whereas 137 workers were assigned to the control hospital where routine activities on infectious health care waste management were performed. Pre and post intervention assessment was done for knowledge, attitude and practices (KAP); and was statistically analyzed. Bivariate and multivariate analysis, independent, paired and unpaired t-test, chi-square with p values, and mean of the responses were calculated. Overall the response rate was 92% at the end of intervention. During the baseline survey, 275 healthcare workers (HCW) included doctors, nurses, paramedics and sanitary workers, and after 3 months of intervention, 255 were reached out to complete the questionnaire. With regard to KAP at baseline, there were no significant differences between two groups at baseline, except for gender and department. However, in the post intervention survey, statistically significance difference (<0.05) between intervention and control group's knowledge, attitude and practices was found. Moreover, within the control group no statistically significant difference was reported (>0.05) after 3 months. Study results suggest that IHWM training could be an effective intervention for improving knowledge, attitudes and practices among health workers regarding infectious waste management. Such training should become a regular feature of all hospitals for reducing the hazards attached with infectious wastes.

High-level radioactive waste management alternatives

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1974-05-01

A summary of a comprehensive overview study of potential alternatives for long-term management of high-level radioactive waste is presented. The concepts studied included disposal in geologic formations, disposal in seabeds, disposal in ice caps, disposal into space, and elimination by transmutation. (TFD)

Waste Management Project fiscal year 1998 multi-year work plan, WBS 1.2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobsen, P.H.

The Waste Management Project manages and integrates (non-TWRS) waste management activities at the site. Activities include management of Hanford wastes as well as waste transferred to Hanford from other DOE, Department of Defense, or other facilities. This work includes handling, treatment, storage, and disposal of radioactive, nonradioactive, hazardous, and mixed solid and liquid wastes. Major Waste Management Projects are the Solid Waste Project, Liquid Effluents Project, and Analytical Services. Existing facilities (e.g., grout vaults and canyons) shall be evaluated for reuse for these purposes to the maximum extent possible.

E-waste Management and Refurbishment Prediction (EMARP) Model for Refurbishment Industries.

PubMed

Resmi, N G; Fasila, K A

2017-10-01

This paper proposes a novel algorithm for establishing a standard methodology to manage and refurbish e-waste called E-waste Management And Refurbishment Prediction (EMARP), which can be adapted by refurbishing industries in order to improve their performance. Waste management, particularly, e-waste management is a serious issue nowadays. Computerization has been into waste management in different ways. Much of the computerization has happened in planning the waste collection, recycling and disposal process and also managing documents and reports related to waste management. This paper proposes a computerized model to make predictions for e-waste refurbishment. All possibilities for reusing the common components among the collected e-waste samples are predicted, thus minimizing the wastage. Simulation of the model has been done to analyse the accuracy in the predictions made by the system. The model can be scaled to accommodate the real-world scenario. Copyright © 2017 Elsevier Ltd. All rights reserved.

Eco-dialysis: the financial and ecological costs of dialysis waste products: is a 'cradle-to-cradle' model feasible for planet-friendly haemodialysis waste management?

PubMed

Piccoli, Giorgina Barbara; Nazha, Marta; Ferraresi, Martina; Vigotti, Federica Neve; Pereno, Amina; Barbero, Silvia

2015-06-01

Approximately 2 million chronic haemodialysis patients produce over 2,000,000 tons of waste per year that includes about 600,000 tons of potentially hazardous waste. The aim of the present study was to analyse the characteristics of the waste that is produced through chronic haemodialysis in an effort to identify strategies to reduce its environmental and financial impact. The study included three dialysis machines and disposables for bicarbonate dialysis, haemodiafiltration (HFR) and lactate dialysis. Hazardous waste is defined as waste that comes into contact with bodily fluids. The weight and cost of waste management was evaluated by various policies of differentiation, ranging from a careful-optimal differentiation to a careless one. The amount of time needed for optimal management was recorded in 30 dialysis sessions. Non-hazardous materials were assessed for potential recycling. The amount of plastic waste that is produced per dialysis session ranges from 1.5 to 8 kg (from 1.1 to 8 kg of potentially hazardous waste), depending upon the type of dialysis machine and supplies, differentiation and emptying policies. The financial cost of waste disposal is high, and is mainly related to hazardous waste disposal, with costs ranging from 2.2 to 16 Euro per session (2.7-21 USD) depending on the waste management policy. The average amount of time needed for careful, optimal differentiation disposal is approximately 1 minute for a haemodialysis session and 2 minutes for HFR. The ecological cost is likewise high: less than one-third of non-hazardous waste (23-28%) is potentially recyclable, while the use of different types of plastic, glues, inks and labels prevents the remaining materials from being recycled. Acknowledging the problem of waste management in dialysis could lead to savings of hundreds of millions of Dollars and to the reuse and recycling of hundreds of tons of plastic waste per year on a world-wide scale with considerable financial and ecological savings. © The Author 2015. Published by Oxford University Press on behalf of ERA-EDTA. All rights reserved.

Medical waste management in Ibadan, Nigeria: Obstacles and prospects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coker, Akinwale; School of Engineering and the Built Environment, University of Wolverhampton, Wolverhampton WV1 1SB; Sangodoyin, Abimbola

Quantification and characterization of medical waste generated in healthcare facilities (HCFs) in a developing African nation has been conducted to provide insights into existing waste collection and disposal approaches, so as to provide sustainable avenues for institutional policy improvement. The study, in Ibadan city, Nigeria, entailed a representative classification of nearly 400 healthcare facilities, from 11 local government areas (LGA) of Ibadan, into tertiary, secondary, primary, and diagnostic HCFs, of which, 52 HCFs were strategically selected. Primary data sources included field measurements, waste sampling and analysis and a questionnaire, while secondary information sources included public and private records from hospitalsmore » and government ministries. Results indicate secondary HCFs generate the greatest amounts of medical waste (mean of 10,238 kg/day per facility) followed by tertiary, primary and diagnostic HCFs, respectively. Characterised waste revealed that only {approx}3% was deemed infectious and highlights opportunities for composting, reuse and recycling. Furthermore, the management practices in most facilities expose patients, staff, waste handlers and the populace to unnecessary health risks. This study proffers recommendations to include (i) a need for sustained cooperation among all key actors (government, hospitals and waste managers) in implementing a safe and reliable medical waste management strategy, not only in legislation and policy formation but also particularly in its monitoring and enforcement and (ii) an obligation for each HCF to ensure a safe and hygienic system of medical waste handling, segregation, collection, storage, transportation, treatment and disposal, with minimal risk to handlers, public health and the environment.« less

Environmental performance of household waste management in Europe - An example of 7 countries.

PubMed

Andreasi Bassi, Susanna; Christensen, Thomas H; Damgaard, Anders

2017-11-01

An attributional life cycle assessment (LCA) of the management of 1ton of household waste was conducted in accordance with ISO 14044:2006 and the ILCD Handbook for seven European countries, namely Germany, Denmark, France, UK, Italy, Poland and Greece, representing different household waste compositions, waste management practices, technologies, and energy systems. National data were collected from a range of sources regarding household waste composition, household sorting efficiency, collection, waste treatments, recycling, electricity and heat composition, and technological efficiencies. The objective was to quantify the environmental performance in the different countries, in order to analyze the sources of the main environmental impacts and national differences which affect the results. In most of the seven countries, household waste management provides environmental benefits when considering the benefits of recycling of materials and recovering and utilization of energy. Environmental benefits come from paper recycling and, to a lesser extent, the recycling of metals and glass. Waste-to-energy plants can lead to an environmental load (as in France) or a saving (Germany and Denmark), depending mainly on the composition of the energy being substituted. Sensitivity analysis and a data quality assessment identified a range of critical parameters, suggesting from where better data should be obtained. The study concluded that household waste management is environmentally the best in European countries with a minimum reliance on landfilling, also induced by the implementation of the Waste Hierarchy, though environmental performance does not correlate clearly with the rate of material recycling. From an environmental point of view, this calls for a change in the waste management paradigm, with less focus on where the waste is routed and more of a focus on the quality and utilization of recovered materials and energy. Copyright © 2017 Elsevier Ltd. All rights reserved.

Greenhouse gas footprint and the carbon flow associated with different solid waste management strategy for urban metabolism in Bangladesh.

PubMed

Islam, K M Nazmul

2017-02-15

Greenhouse gas (GHG) emissions from municipal solid waste (MSW) and associated climate change consequences are gripping attention globally, while MSW management as a vital subsystem of urban metabolism significantly influences the urban carbon cycles. This study evaluates the GHG emissions and carbon flow of existing and proposed MSW management in Bangladesh through scenario analysis, including landfill with landfill gas (LFG) recovery, waste to energy (WtE), and material recovery facility (MRF). The analysis indicates that, scenario H 2 and H 5 emitted net GHGs -152.20kg CO 2 eq. and -140.32kg CO 2 eq., respectively, in comparison with 420.88kg CO 2 eq. of scenario H 1 for managing per ton of wastes during the reference year 2015. The annual horizontal carbon flux of the waste input was 319Gg and 158Gg during 2015 in Dhaka and Chittagong, respectively. An integrated strategy of managing the wastes in the urban areas of Bangladesh involving WtE incineration plant and LFG recovery to generate electricity as well as MRF could reverse back 209.46Gg carbon and 422.29Gg carbon to the Chittagong and Dhaka urban system, respectively. This study provides valuable insights for the MSW policy framework and revamp of existing MSW management practices with regards to reduction of GHGs emissions from the waste sector in Bangladesh. Copyright © 2016 Elsevier B.V. All rights reserved.

Non linear relationship between change in awareness in municipal solid waste management and domestic wastewater management - A case of the Jodipan and Ksatrian village, Malang, East Java

NASA Astrophysics Data System (ADS)

Zakiyya, Nida Maisa; Sarli, Prasanti Widyasih; Soewondo, Prayatni

2017-11-01

In developing countries the awareness on the importance of sanitation facilities, whether it is for municipal solid waste or domestic wastewater treatment, is still very low. Jodipan and Ksatrian Village, in Malang, East Java, are two slum areas that have recently been improved visually by using simple colorful paints. The visual improvement was expected to increase the resident's awareness on the importance of keeping the area clean; adjacent to the project, a new municipal waste management system was also put in place, changing the president's behaviour towards municipal solid waste. This study focuses on the relationship between community awareness in municipal solid waste management and domestic wastewater management. The result is expected to be an input for the government to enhance wastewater infrastructure program and its sustainability, related to its awareness on municipal solid waste. A descriptive model through questionnaire to 48 households of Jodipan sub district in Kampung Warna-warni and 69 households of Ksatrian sub district in Kampung 3D by random sampling, with an error of 0.1, was used to conduct this research. A nonlinear relationship between the change in awareness in municipal solid waste management (MSW) and domestic wastewater management was observed, with only 0.1312 of determination coefficient. Weak Spearman correlation coefficient number was found, ranging from 0.284 to 0.39, indicating another parameter turned into a role on affecting the awareness of wastewater. Further study about another parameter (eg. social and economic parameter) intervension on sanitation awareness could be investigated.

Modelling a suitable location for Urban Solid Waste Management using AHP method and GIS -A geospatial approach and MCDM Model

NASA Astrophysics Data System (ADS)

Iqbal, M.; Islam, A.; Hossain, A.; Mustaque, S.

2016-12-01

Multi-Criteria Decision Making(MCDM) is advanced analytical method to evaluate appropriate result or decision from multiple criterion environment. Present time in advanced research, MCDM technique is progressive analytical process to evaluate a logical decision from various conflict. In addition, Present day Geospatial approach (e.g. Remote sensing and GIS) also another advanced technical approach in a research to collect, process and analyze various spatial data at a time. GIS and Remote sensing together with the MCDM technique could be the best platform to solve a complex decision making process. These two latest process combined very effectively used in site selection for solid waste management in urban policy. The most popular MCDM technique is Weighted Linear Method (WLC) where Analytical Hierarchy Process (AHP) is another popular and consistent techniques used in worldwide as dependable decision making. Consequently, the main objective of this study is improving a AHP model as MCDM technique with Geographic Information System (GIS) to select a suitable landfill site for urban solid waste management. Here AHP technique used as a MCDM tool to select the best suitable landfill location for urban solid waste management. To protect the urban environment in a sustainable way municipal waste needs an appropriate landfill site considering environmental, geological, social and technical aspect of the region. A MCDM model generate from five class related which related to environmental, geological, social and technical using AHP method and input the result set in GIS for final model location for urban solid waste management. The final suitable location comes out that 12.2% of the area corresponds to 22.89 km2 considering the total study area. In this study, Keraniganj sub-district of Dhaka district in Bangladesh is consider as study area which is densely populated city currently undergoes an unmanaged waste management system especially the suitable landfill sites for waste dumping site.

Analysis on 3RWB model (Reduce, reuse, recycle, and waste bank) in comprehensive waste management toward community-based zero waste

NASA Astrophysics Data System (ADS)

Affandy, Nur Azizah; Isnaini, Enik; Laksono, Arif Budi

2017-06-01

Waste management becomes a serious issue in Indonesia. Significantly, waste production in Lamongan Regency is increasing in linear with the growth of population and current people activities, creating a gap between waste production and waste management. It is a critical problem that should be solved immediately. As a reaction to the issue, the Government of Lamongan Regency has enacted a new policy regarding waste management through a program named Lamongan Green and Clean (LGC). From the collected data, it showed that the "wet waste" or "organic waste" was approximately 63% of total domestic waste. With such condition, it can be predicted that the trashes will decompose quite quickly. From the observation, it was discovered that the generated waste was approximately 0.25 kg/person/day. Meanwhile, the number of population in Tumenggungan Village, Lamongan (data obtained from Monograph in Lamongan district, 2012) was 4651 people. Thus, it can be estimated the total waste in Lamongan was approximately 0.25 kg/person/day x 4651 characters = 930 kg/day. Within 3RWB Model, several stages have to be conducted. In the planning stage, the promotion of self-awareness among the communities in selecting and managing waste due to their interest in a potential benefit, is done. It indicated that community's awareness of waste management waste grew significantly. Meanwhile in socialization stage, each village staff, environmental expert, and policymaker should bear significant role in disseminating the awareness among the people. In the implementation phase, waste management with 3RWB model is promoted by applying it among of the community, starting from selection, waste management, until recycled products sale through the waste bank. In evaluation stage, the village managers, environmental expert, and waste managers are expected to regularly supervise and evaluate the whole activity of the waste management.

Oak Ridge National Laboratory Waste Management Plan, fiscal year 1994. Revision 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, J.W.

1993-12-01

US Department of Energy (DOE) Order 5820.2A was promulgated in final form on September 26, 1988. The order requires heads of field organizations to prepare and to submit updates on the waste management plans for all operations under their purview according to the format in Chap. 6, {open_quotes}Waste Management Plan Outline.{close_quotes} These plans are to be submitted by the DOE Oak Ridge Operations Office (DOE-ORO) in December of each year and distributed to the DP-12, ES&H-1, and other appropriate DOE Headquarters (DOE-HQ) organizations for review and comment. This document was prepared in response to this requirement for fiscal year (FY)more » 1994. The Oak Ridge National Laboratory (ORNL) waste management mission is reduction, collection, storage, treatment, and disposal of DOE wastes, generated primarily in pursuit of ORNL missions, in order to protect human health and safety and the environment. In carrying out this mission, waste management staff in the Waste Management and Remedial Action Division (WMRAD) will (1) guide ORNL in optimizing waste reduction and waste management capabilities and (2) conduct waste management operations in a compliant, publicly acceptable, technically sound, and cost-efficient manner. Waste management requirements for DOE radioactive wastes are detailed in DOE Order 5820.2A, and the ORNL Waste Management Program encompasses all elements of this order. The requirements of this DOE order and other appropriate DOE orders, along with applicable Tennessee Department of Environment and Conservation and US Environmental Protection Agency (EPA) rules and regulations, provide the principal source of regulatory guidance for waste management operations at ORNL. The objective of this document is compilation and consolidation of information on how the ORNL Waste Management Program is conducted, which waste management facilities are being used to manage wastes, what activities are planned for FY 1994, and how all of the activities are documented.« less

Public-private sector partnership in household waste management as perceived by residents in south-west Nigeria.

PubMed

Ezebilo, Eugene E; Animasaun, Emmanuel D

2012-08-01

In most developing countries public-private sector partnership is becoming increasingly applied in household waste management service delivery especially in urban areas to reduce cost and improve effectiveness. This paper reports a study of householders' perceptions of public-private sector partnership in provision of household waste management services in Ilorin, south-west Nigeria. A multistage random sampling technique was used to select 224 households for the study. The data generated from the survey were analysed using a binary logit model. The results show that most of the respondents were of the opinion that the public-private partnership has not been able to improve household waste management services. Time taken to visit solid waste collection point, income and marital status negatively influenced their perceptions, while activities of sanitary inspectors, occupation and gender had positive influence. The public-private partnership will be more effective and sustainable if the public sector could pay more attention to performance monitoring and accountability.

A fuzzy chance-constrained programming model with type 1 and type 2 fuzzy sets for solid waste management under uncertainty

NASA Astrophysics Data System (ADS)

Ma, Xiaolin; Ma, Chi; Wan, Zhifang; Wang, Kewei

2017-06-01

Effective management of municipal solid waste (MSW) is critical for urban planning and development. This study aims to develop an integrated type 1 and type 2 fuzzy sets chance-constrained programming (ITFCCP) model for tackling regional MSW management problem under a fuzzy environment, where waste generation amounts are supposed to be type 2 fuzzy variables and treated capacities of facilities are assumed to be type 1 fuzzy variables. The evaluation and expression of uncertainty overcome the drawbacks in describing fuzzy possibility distributions as oversimplified forms. The fuzzy constraints are converted to their crisp equivalents through chance-constrained programming under the same or different confidence levels. Regional waste management of the City of Dalian, China, was used as a case study for demonstration. The solutions under various confidence levels reflect the trade-off between system economy and reliability. It is concluded that the ITFCCP model is capable of helping decision makers to generate reasonable waste-allocation alternatives under uncertainties.

Sustainable Materials Management: Non-Hazardous Materials and Waste Management Hierarchy

EPA Pesticide Factsheets

EPA developed the non-hazardous materials and waste management hierarchy in recognition that no single waste management approach is suitable for managing all materials and waste streams in all circumstances.

Perspectives of policy-makers and stakeholders about health care waste management in community-based care in South Africa: a qualitative study.

PubMed

Hangulu, Lydia; Akintola, Olagoke

2017-04-19

In South Africa, a new primary health care (PHC) re-engineering initiative aims to scale up the provision of community-based care (CBC). A central element in this initiative is the use of outreach teams comprising nurses and community health workers to provide care to the largely poor and marginalised communities across the country. The provision of care will inevitably lead to an increase in the amount of health care waste (HCW) generated in homes and suggests the need to pay more attention to the HCW that emanates from homes where there is care of a patient. CBC in South Africa is guided by the home-based care policy. However, this policy does not deal with issues about how HCW should be managed in CBC. This study sought to explore health care waste management (HCWM) in CBC in South Africa from the policy-makers' and stakeholders' perspective. Semi-structured interviews were conducted with 9 policy-makers and 21 stakeholders working in 29 communities in Durban, South Africa. Interviews were conducted in English; were guided by an interview guide with open-ended questions. Data was analysed thematically. The Durban Solid waste (DSW) unit of the eThekwini municipality is responsible for overseeing all waste management programmes in communities. Lack of segregation of waste and illegal dumping of waste were the main barriers to proper management practices of HCW at household level while at the municipal level, corrupt tender processes and inadequate funding for waste management programmes were identified as the main barriers. In order to address these issues, all the policy-makers and stakeholders have taken steps to collaborate and develop education awareness programmes. They also liaise with various government offices to provide resources aimed at waste management programmes. HCW is generated in CBC and it is poorly managed and treated as domestic waste. With the rollout of the new primary health care model, there is a greater need to consider HCWM in CBC. There is need for the Department of Health to work together with the municipality to ensure that they devise measures that will help to deal with improper HCWM in the communities.

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

40 CFR 62.14430 - Must I prepare a waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Must I prepare a waste management plan... 20, 1996 Waste Management Plan § 62.14430 Must I prepare a waste management plan? Yes. All HMIWI owners or operators must have a waste management plan. ...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

40 CFR 62.14430 - Must I prepare a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false Must I prepare a waste management plan... December 1, 2008 Waste Management Plan § 62.14430 Must I prepare a waste management plan? Yes. All HMIWI owners or operators must have a waste management plan. ...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management... Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing construction, reconstruction, or modification. ...

40 CFR 62.14430 - Must I prepare a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false Must I prepare a waste management plan... December 1, 2008 Waste Management Plan § 62.14430 Must I prepare a waste management plan? Yes. All HMIWI owners or operators must have a waste management plan. ...

40 CFR 62.14430 - Must I prepare a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false Must I prepare a waste management plan... 20, 1996 Waste Management Plan § 62.14430 Must I prepare a waste management plan? Yes. All HMIWI owners or operators must have a waste management plan. ...

40 CFR 62.14430 - Must I prepare a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false Must I prepare a waste management plan... 20, 1996 Waste Management Plan § 62.14430 Must I prepare a waste management plan? Yes. All HMIWI owners or operators must have a waste management plan. ...

Waste Management Improvement Initiatives at Atomic Energy of Canada Limited - 13091

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan, Nicholas; Adams, Lynne; Wong, Pierre

2013-07-01

Atomic Energy of Canada Limited's (AECL) Chalk River Laboratories (CRL) has been in operation for over 60 years. Radioactive, mixed, hazardous and non-hazardous wastes have been and continue to be generated at CRL as a result of research and development, radioisotope production, reactor operation and facility decommissioning activities. AECL has implemented several improvement initiatives at CRL to simplify the interface between waste generators and waste receivers: - Introduction of trained Waste Officers representing their facilities or activities at CRL; - Establishment of a Waste Management Customer Support Service as a Single-Point of Contact to provide guidance to waste generators formore » all waste management processes; and - Implementation of a streamlined approach for waste identification with emphasis on early identification of waste types and potential disposition paths. As a result of implementing these improvement initiatives, improvements in waste management and waste transfer efficiencies have been realized at CRL. These included: 1) waste generators contacting the Customer Support Service for information or guidance instead of various waste receivers; 2) more clear and consistent guidance provided to waste generators for waste management through the Customer Support Service; 3) more consistent and correct waste information provided to waste receivers through Waste Officers, resulting in reduced time and resources required for waste management (i.e., overall cost); 4) improved waste minimization and segregation approaches, as identified by in-house Waste Officers; and 5) enhanced communication between waste generators and waste management groups. (authors)« less

A review of mechanochemistry applications in waste management.

PubMed

Guo, Xiuying; Xiang, Dong; Duan, Guanghong; Mou, Peng

2010-01-01

Mechanochemistry is defined to describe the chemical and physicochemical transformation of substances during the aggregation caused by the mechanical energy. Mechanochemical technology has several advantages, such as simple process, ecological safety and the possibility of obtaining a product in the metastable state. It potentially has a prospective application in pollution remediation and waste management. Therefore, this paper aims to give an overall review of the mechanochemistry applications in waste management and the related mechanisms. Based on our study, the modification of fly ash and asbestos-containing wastes (ACWs) can be achieved by mechanochemical technology. Waste metal oxides can be transformed into easily recyclable sulfide by mechanochemical sulfidization. Besides, the waste plastics and rubbers, which are usually very difficult to be recycled, can also be recycled by mechanochemical technology.

A bi-level environmental impact assessment framework for comparing construction and demolition waste management strategies.

PubMed

Yazdanbakhsh, Ardavan

2018-04-27

Several pioneering life cycle assessment (LCA) studies have been conducted in the past to assess the environmental impact of specific methods for managing mineral construction and demolition waste (MCDW), such as recycling the waste for use in concrete. Those studies focus on comparing the use of recycled MCDW and that of virgin components to produce materials or systems that serve specified functions. Often, the approaches adopted by the studies do not account for the potential environmental consequence of avoiding the existing or alternative waste management practices. The present work focuses on how product systems need to be defined in recycling LCA studies and what processes need to be within the system boundaries. A bi-level LCA framework is presented for modelling alternative waste management approaches in which the impacts are measured and compared at two scales of strategy and decision-making. Different functional units are defined for each level, all of which correspond to the same flow of MCDW in a cascade of product systems. For the sole purpose of demonstrating how the framework is implemented an illustrative example is presented, based on real data and a number of simplifying assumptions, which compares the impacts of a number of potential MCDW management strategies in New York City. Copyright © 2018 Elsevier Ltd. All rights reserved.

Composition, Production Rate and Management of Dental Solid Waste in 2017 in Birjand, Iran.

PubMed

Momeni, Habibe; Tabatabaei Fard, Seyyedeh Fatemeh; Arefinejad, Aliye; Afzali, Afsane; Talebi, Farkhonde; Rahmanpour Salmani, Elham

2018-01-01

The presence of toxic and pathogenic agents in the dental waste products has made it to be classified as "hazardous waste." To assess dental waste production rate and composition and approaches used to manage these waste products in 2017 in Birjand, Iran. 48 dental clinics were evaluated in two months of 2017. Sampling was performed from each clinic 3 times a week. Samples were manually divided into 5 categories of chemical-pharmaceutical, infectious, semi-household, sharp and cutting materials, and toxic waste products, and weighed. A checklist containing 25 questions was used to evaluate the aspects of waste management in dental clinics. The total amount of waste products generated in dental clinics was 7848.02 kg/ year in which semi-household waste had the highest quantity (4263.411 kg/year) and toxic waste had the lowest quantity (9.275 kg/year). Components with the highest amounts in dentistry waste products were nylon gloves (16.7%), paper and cardboard (13.4%), latex gloves (10.8%), and pharmaceuticals (10.2%). Waste separation was restricted to sharp and cutting waste. More than half (57%) of dental units were equipped with amalgam filter. Fixing solutions were directly discharged to sewage in 48.6% of clinics. There was no program to reduce waste generation in 54% of the clinics. Autoclave was the main tool for sterilizing dental instruments. This study showed a remarkable share of recyclable materials in the composition of dental waste and lack of special approach to manage waste in dental clinics. It is necessary to plan for minimizing generation of, separating, and recycling waste at source.

Municipal solid waste management in the Southern Province of Sri Lanka: Problems, issues and challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vidanaarachchi, Chandana K.; Yuen, Samuel T.S.; Pilapitiya, Sumith

2006-07-01

This paper describes the problems, issues and challenges faced by Sri Lanka based on the outcome of a recent study conducted in the country's Southern Province. The study consists of a public survey, discussions with local authority staff involved in waste management, discussions with Provincial Council and Government officials, dialogue with local politicians, review of documents and field observations. The study revealed that only 24% of the households have access to waste collection and that in rural areas it was less than 2%. A substantial number of households in areas without waste collection expect local authorities to collect their waste.more » The study also showed that most sites in the province are under capacity to handle any increased demand. Urgent and immediate improvement of the waste disposal sites is necessary to meet the current demand for improved waste collection. The study also revealed that there is a high willingness of people for home composting.« less

Review of LCA studies of solid waste management systems – Part II: Methodological guidance for a better practice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laurent, Alexis, E-mail: alau@dtu.dk; Clavreul, Julie; Bernstad, Anna

Highlights: • We perform a critical review of 222 LCA studies of solid waste management systems. • We analyse the past LCA practice against the ISO standard and ILCD Handbook guidance. • Malpractices exist in many methodological aspects with large variations among studies. • Many of these aspects are important for the reliability of the results. • We provide detailed recommendations to practitioners of waste management LCAs. - Abstract: Life cycle assessment (LCA) is increasingly used in waste management to identify strategies that prevent or minimise negative impacts on ecosystems, human health or natural resources. However, the quality of themore » provided support to decision- and policy-makers is strongly dependent on a proper conduct of the LCA. How has LCA been applied until now? Are there any inconsistencies in the past practice? To answer these questions, we draw on a critical review of 222 published LCA studies of solid waste management systems. We analyse the past practice against the ISO standard requirements and the ILCD Handbook guidelines for each major step within the goal definition, scope definition, inventory analysis, impact assessment, and interpretation phases of the methodology. Results show that malpractices exist in several aspects of the LCA with large differences across studies. Examples are a frequent neglect of the goal definition, a frequent lack of transparency and precision in the definition of the scope of the study, e.g. an unclear delimitation of the system boundaries, a truncated impact coverage, difficulties in capturing influential local specificities such as representative waste compositions into the inventory, and a frequent lack of essential sensitivity and uncertainty analyses. Many of these aspects are important for the reliability of the results. For each of them, we therefore provide detailed recommendations to practitioners of waste management LCAs.« less

An expert system for municipal solid waste management simulation analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsieh, M.C.; Chang, N.B.

1996-12-31

Optimization techniques were usually used to model the complicated metropolitan solid waste management system to search for the best dynamic combination of waste recycling, facility siting, and system operation, where sophisticated and well-defined interrelationship are required in the modeling process. But this paper applied the Concurrent Object-Oriented Simulation (COOS), a new simulation software construction method, to bridge the gap between the physical system and its computer representation. The case study of Kaohsiung solid waste management system in Taiwan is prepared for the illustration of the analytical methodology of COOS and its implementation in the creation of an expert system.

The concept of value stream mapping to reduce of work-time waste as applied the smart construction management

NASA Astrophysics Data System (ADS)

Elizar, Suripin, Wibowo, Mochamad Agung

2017-11-01

Delays in construction sites occur due to systematic additions of time waste in various activities that are part of the construction process. Work-time waste is non-adding value activity which used to differentiate between physical construction waste found on site and other waste which occurs during the construction process. The aim of this study is identification using the concept of Value Stream Mapping (VSM) to reduce of work-time waste as applied the smart construction management.VSM analysis is a method of business process improvement. The application of VSM began in the manufacturing community. The research method base on theoretically informed case study and literature review. The data have collected using questionnaire through personal interviews from 383 respondents on construction project in Indonesia. The results show that concept of VSM can identify causes of work-time waste. Base on result of questioners and quantitative approach analysis was obtained 29 variables that influence of work-time waste or non-value-adding activities. Base on three cases of construction project founded that average 14.88% of working time was classified as waste. Finally, the concept of VSM can recommend to identification of systematic for reveal current practices and opportunities for improvement towards global challenges. The concept of value stream mapping can help optimize to reduce work-time waste and improve quality standard of construction management. The concept is also can help manager to make a decision to reduce work-time waste so as to obtain of result in more efficient for performance and sustainable construction project.

Health-care waste management in India.

PubMed

Patil, A D; Shekdar, A V

2001-10-01

Health-care waste management in India is receiving greater attention due to recent regulations (the Biomedical Wastes (Management & Handling) Rules, 1998). The prevailing situation is analysed covering various issues like quantities and proportion of different constituents of wastes, handling, treatment and disposal methods in various health-care units (HCUs). The waste generation rate ranges between 0.5 and 2.0 kg bed-1 day-1. It is estimated that annually about 0.33 million tonnes of waste are generated in India. The solid waste from the hospitals consists of bandages, linen and other infectious waste (30-35%), plastics (7-10%), disposable syringes (0.3-0.5%), glass (3-5%) and other general wastes including food (40-45%). In general, the wastes are collected in a mixed form, transported and disposed of along with municipal solid wastes. At many places, authorities are failing to install appropriate systems for a variety of reasons, such as non-availability of appropriate technologies, inadequate financial resources and absence of professional training on waste management. Hazards associated with health-care waste management and shortcomings in the existing system are identified. The rules for management and handling of biomedical wastes are summarised, giving the categories of different wastes, suggested storage containers including colour-coding and treatment options. Existing and proposed systems of health-care waste management are described. A waste-management plan for health-care establishments is also proposed, which includes institutional arrangements, appropriate technologies, operational plans, financial management and the drawing up of appropriate staff training programmes.

THE IMPACT OF MUNICIPAL SOLID WASTE MANAGEMENT ON GREENHOUSE GAS EMISSIONS IN THE UNITED STATES

EPA Science Inventory

Technological advancements in United States (U.S.) municipal solid waste (MSW) disposal and a focus on the environmental advantages of integrated MSW management have greatly reduced the environmental impacts of MSW management, including greenhouse gas (GHG) emissions. This study ...

Hazardous-waste analysis plan for LLNL operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, R.S.

The Lawrence Livermore National Laboratory is involved in many facets of research ranging from nuclear weapons research to advanced Biomedical studies. Approximately 80% of all programs at LLNL generate hazardous waste in one form or another. Aside from producing waste from industrial type operations (oils, solvents, bottom sludges, etc.) many unique and toxic wastes are generated such as phosgene, dioxin (TCDD), radioactive wastes and high explosives. One key to any successful waste management program must address the following: proper identification of the waste, safe handling procedures and proper storage containers and areas. This section of the Waste Management Plan willmore » address methodologies used for the Analysis of Hazardous Waste. In addition to the wastes defined in 40 CFR 261, LLNL and Site 300 also generate radioactive waste not specifically covered by RCRA. However, for completeness, the Waste Analysis Plan will address all hazardous waste.« less

The Optimized Integration of the Decontamination Plan and the Radwaste Management Plan into Decommissioning Plan to the VVR-S Research Reactor from Romania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barariu, G.

2008-07-01

The paper presents the progress of the Decontamination Plan and Radioactive Waste Management Plan which accompanies the Decommissioning Plan for research reactor VVR-S located in Magurele, Ilfov, near Bucharest, Romania. The new variant of the Decommissioning Plan was elaborated taking into account the IAEA recommendation concerning radioactive waste management. A new feasibility study for VVR-S decommissioning was also elaborated. The preferred safe management strategy for radioactive wastes produced by reactor decommissioning is outlined. The strategy must account for reactor decommissioning, as well as rehabilitation of the existing Radioactive Waste Treatment Plant and the upgrade of the Radioactive Waste Disposal Facilitymore » at Baita-Bihor. Furthermore, the final rehabilitation of the laboratories and reusing of cleaned reactor building is envisaged. An inventory of each type of radioactive waste is presented. The proposed waste management strategy is selected in accordance with the IAEA assistance. Environmental concerns are a part of the radioactive waste management strategy. In conclusion: The current version 8 of the Draft Decommissioning Plan which include the Integrated concept of Decontamination and Decommissioning and Radwaste Management, reflects the substantial work that has been incorporated by IFIN-HH in collaboration with SITON, which has resulted in substantial improvement in document The decommissioning strategy must take into account costs for VVR-S Reactor decommissioning, as well as costs for much needed refurbishments to the radioactive waste treatment plant and the Baita-Bihor waste disposal repository. Several improvements to the Baita-Bihor repository and IFIN-HH waste treatment facility were proposed. The quantities and composition of the radioactive waste generated by VVR-S Reactor dismantling were again estimated by streams and the best demonstrated practicable processing solution was proposed. The estimated quantities of materials to be managed in the near future raise some issues that need to be solved swiftly, such as treatment of aluminum and lead and graphite management. It is envisaged that these materials to be treated to Subsidiary for Nuclear Research (SCN) Pitesti. (authors)« less

Knowledge and awareness regarding biomedical waste management in dental teaching institutions in India- A systematic review

PubMed Central

Kapoor, Daljit; Nirola, Ashutosh; Kapoor, Vinod

2014-01-01

Objectives: Proper handling, treatment and disposal of biomedical wastes are important elements in any health care setting. Not much attention has been paid to the management of Biomedical Waste (BMW) in recent years, in dental colleges and hospitals in India. The present systematic review was conducted to assess knowledge and awareness regarding BMW management among staff and students of dental teaching institutions in India. Material and Methods: A systematic review of relevant cross-sectional studies was conducted regarding BMW management in India in dental teaching institutions in India. Six studies were finally included in the present review after conducting both electronic and manual search like Pubmed, EMBASE etc. and after making necessary exclusions. Potential biases were addressed and relevant data was extracted by the concerned investigators. Results: Six studies were finally included in the review. Colour coding of wastes was not done by 67% of the subjects in one of the studies conducted in Haryana. Almost all the subjects agreed to the fact that exposure to hazardous health care waste can result in disease or infection in another study. According to another study reports, none of the respondents was able to list the legislative act regarding BMW when asked. Conclusions: The results of the present review showed that knowledge and awareness level of subjects was inadequate and there is considerable variation in practice and management regarding BMW. There is a great need for continuing education and training programmes to be conducted in dental teaching institutions in India. Key words:Biomedical waste, knowledge, awareness, dentists, institution. PMID:25593667

Knowledge and awareness regarding biomedical waste management in dental teaching institutions in India- A systematic review.

PubMed

Kapoor, Daljit; Nirola, Ashutosh; Kapoor, Vinod; Gambhir, Ramandeep-Singh

2014-10-01

Proper handling, treatment and disposal of biomedical wastes are important elements in any health care setting. Not much attention has been paid to the management of Biomedical Waste (BMW) in recent years, in dental colleges and hospitals in India. The present systematic review was conducted to assess knowledge and awareness regarding BMW management among staff and students of dental teaching institutions in India. A systematic review of relevant cross-sectional studies was conducted regarding BMW management in India in dental teaching institutions in India. Six studies were finally included in the present review after conducting both electronic and manual search like Pubmed, EMBASE etc. and after making necessary exclusions. Potential biases were addressed and relevant data was extracted by the concerned investigators. Six studies were finally included in the review. Colour coding of wastes was not done by 67% of the subjects in one of the studies conducted in Haryana. Almost all the subjects agreed to the fact that exposure to hazardous health care waste can result in disease or infection in another study. According to another study reports, none of the respondents was able to list the legislative act regarding BMW when asked. The results of the present review showed that knowledge and awareness level of subjects was inadequate and there is considerable variation in practice and management regarding BMW. There is a great need for continuing education and training programmes to be conducted in dental teaching institutions in India. Key words:Biomedical waste, knowledge, awareness, dentists, institution.

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What is a waste management plan? 60... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Preconstruction Siting Analysis Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that...

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What is a waste management plan? 60... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Preconstruction Siting Analysis Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that...

40 CFR 60.2620 - What is a waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What is a waste management plan? 60... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emissions Guidelines and Compliance Times for..., 1999 Model Rule-Waste Management Plan § 60.2620 What is a waste management plan? A waste management...

40 CFR 60.3010 - What is a waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What is a waste management plan? 60... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Emission Guidelines and Compliance Times for... Rule-Waste Management Plan § 60.3010 What is a waste management plan? A waste management plan is a...

RFID technology for hazardous waste management and tracking.

PubMed

Namen, Anderson Amendoeira; Brasil, Felipe da Costa; Abrunhosa, Jorge José Gouveia; Abrunhosa, Glaucia Gomes Silva; Tarré, Ricardo Martinez; Marques, Flávio José Garcia

2014-09-01

The illegal dumping of hazardous waste is one of the most concerning occurrences related to illegal waste activities. The waste management process is quite vulnerable, especially when it comes to assuring the right destination for the delivery of the hazardous waste. The purpose of this paper is to present a new system design and prototype for applying the RFID technology so as to guarantee the correct destination for the hazardous waste delivery. The aim of this innovative approach, compared with other studies that employ the same technology to the waste disposal process, is to focus on the certification that the hazardous waste will be delivered to the right destination site and that no inappropriate disposal will occur in the transportation stage. These studies were carried out based on data collected during visits to two hazardous waste producer companies in Brazil, where the material transportation and delivery to a company in charge of the waste disposal were closely monitored. © The Author(s) 2014.

Characterization of urban solid waste in Chihuahua, Mexico.

PubMed

Gomez, Guadalupe; Meneses, Montserrat; Ballinas, Lourdes; Castells, Francesc

2008-12-01

The characterization of urban solid waste generation is fundamental for adequate decision making in the management strategy of urban solid waste in a city. The objective of this study is to characterize the waste generated in the households of Chihuahua city, and to compare the results obtained in areas of the city with three different socioeconomic levels. In order to identify the different socioeconomic trends in waste generation and characterization, 560 samples of solid waste were collected during 1 week from 80 households in Chihuahua and were hand sorted and classified into 15 weighted fractions. The average waste generation in Chihuahua calculated in this study was 0.676 kg per capita per day in April 2006. The main fractions were: organic (48%), paper (16%) and plastic (12%). Results show an increased waste generation associated with the socioeconomic level. The characterization in amount and composition of urban waste is the first step needed for the successful implementation of an integral waste management system.

Application of material flow analysis to estimate the efficiency of e-waste management systems: the case of Lithuania.

PubMed

Gurauskiene, Inga; Stasiskiene, Zaneta

2011-07-01

Electrical and electronic equipment (EEE) has penetrated everyday life. The EEE industry is characterized by a rapid technological change which in turn prompts consumers to replace EEE in order to keep in step with innovations. These factors reduce an EEE life span and determine the exponential growth of the amount of obsolete EEE as well as EEE waste (e-waste). E-waste management systems implemented in countries of the European Union (EU) are not able to cope with the e-waste problem properly, especially in the new EU member countries. The analysis of particular e-waste management systems is essential in evaluation of the complexity of these systems, describing and quantifying the flows of goods throughout the system, and all the actors involved in it. The aim of this paper is to present the research on the regional agent based material flow analysis in e-waste management systems, as a measure to reveal the potential points for improvement. Material flow analysis has been performed as a flow of goods (EEE). The study has shown that agent-based EEE flow analysis incorporating a holistic and life cycle thinking approach in national e-waste management systems gives a broader view to the system than a common administrative one used to cover. It helps to evaluate the real efficiency of e-waste management systems and to identify relevant impact factors determining the current operation of the system.

Radioactive Wastes.

PubMed

Choudri, B S; Charabi, Yassine; Baawain, Mahad; Ahmed, Mushtaque

2017-10-01

Papers reviewed herein present a general overview of radioactive waste related activities around the world in 2016. The current reveiw include studies related to safety assessments, decommission and decontamination of nuclear facilities, fusion facilities, transportation. Further, the review highlights on management solutions for the final disposal of low and high level radioactive wastes (LLW and HLW), interim storage and final disposal options for spent fuel (SF), and tritiated wastes, with a focus on environmental impacts due to the mobility of radionuclides in ecosystem, water and soil alongwith other progress made in the management of radioactive wastes.

[Household waste management in the health district of Builaska in Mbuji-Mayi, Democratic Republic of Congo].

PubMed

Kangoy, Kasangye; Ngoyi, John; Mudimbiyi, Olive

2016-01-01

The presence of household waste on public roads affects environmental health leading to unsanitary conditions which may cause disease outbreaks, some of which may occur in epidemic form. Over the past two decades, waste management has become increasingly complex both for developing and underdeveloping countries. This study aims to determine the types of waste and the management of waste generated by the households. This descriptive cross-sectional study conducted in the health district of Bulaska, Kasai Oriental, is a forward-looking approach based upon interview and active observation. The questionnaire was addressed to the head of household or the delegate out of 170 households, representing a convenience sample, from 21 to 25 June 2010. This study revealed that: 94.7% of respondents who answered our questionnaire were female; 47% of respondents had a primary level of study; 41.1% of respondents were housewives; the average household size was 7 people per household; in 83.5% of cases the wastes generated were solid. 50% of households in the health area used public road for trash disposal. Given the results of this study, further development of awareness programs on environmental sanitation is necessary.

Toward zero waste: composting and recycling for sustainable venue based events.

PubMed

Hottle, Troy A; Bilec, Melissa M; Brown, Nicholas R; Landis, Amy E

2015-04-01

This study evaluated seven different waste management strategies for venue-based events and characterized the impacts of event waste management via waste audits and the Waste Reduction Model (WARM). The seven waste management scenarios included traditional waste handling methods (e.g. recycle and landfill) and management of the waste stream via composting, including purchasing where only compostable food service items were used during the events. Waste audits were conducted at four Arizona State University (ASU) baseball games, including a three game series. The findings demonstrate a tradeoff among CO2 equivalent emissions, energy use, and landfill diversion rates. Of the seven waste management scenarios assessed, the recycling scenarios provide the greatest reductions in CO2 eq. emissions and energy use because of the retention of high value materials but are compounded by the difficulty in managing a two or three bin collection system. The compost only scenario achieves complete landfill diversion but does not perform as well with respect to CO2 eq. emissions or energy. The three game series was used to test the impact of staffed bins on contamination rates; the first game served as a baseline, the second game employed staffed bins, and the third game had non staffed bins to determine the effect of staffing on contamination rates. Contamination rates in both the recycling and compost bins were tracked throughout the series. Contamination rates were reduced from 34% in the first game to 11% on the second night (with the staffed bins) and 23% contamination rates at the third game. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessment of the health care waste generation rates and its management system in hospitals of Addis Ababa, Ethiopia, 2011

PubMed Central

2013-01-01

Background Healthcare waste management options are varying in Ethiopia. One of the first critical steps in the process of developing a reliable waste management plan requires a widespread understanding of the amount and the management system. This study aimed to assess the health care waste generation rate and its management system in some selected hospitals located in Addis Ababa, Ethiopia. Methods Six hospitals in Addis Ababa, (three private and three public), were selected using simple random sampling method for this work. Data was recorded by using an appropriately designed questionnaire, which was completed for the period of two months. The calculations were based on the weights of the health care wastes that were regularly generated in the selected hospitals over a one week period during the year 2011. Average generation indexes were determined in relation to certain important factors, like the type of hospitals (public vs private). Results The median waste generation rate was found to be varied from 0.361- 0.669 kg/patient/day, comprised of 58.69% non-hazardous and 41.31% hazardous wastes. The amount of waste generated was increased as the number of patients flow increased (rs=1). Public hospitals generated high proportion of total health care wastes (59.22%) in comparison with private hospitals (40.48%). The median waste generation rate was significantly vary between hospitals with Kruskal-Wallis test (X2=30.65, p=0.0001). The amount of waste was positively correlated with the number of patients (p < 0.05). The waste separation and treatment practices were very poor. Other alternatives for waste treatment rather than incineration such as a locally made autoclave should be evaluated and implemented. Conclusion These findings revealed that the management of health care waste at hospitals in Addis Ababa city was poor. PMID:23311573

Current status of waste management in Botswana: A mini-review.

PubMed

Mmereki, Daniel

2018-05-01

Effective waste management practices are not all about legislative solutions, but a combination of the environmental, social, technical, technically skilled human resources, financial and technological resources, resource recycling, environmental pollution awareness programmes and public participation. As a result of insufficient resources, municipal solid waste (MSW) in transition and developing countries like Botswana remains a challenge, and it is often not yet given highest priority. In Botswana, the environment, public health and other socio-economic aspects are threatened by waste management practices due to inadequate implementation and enforcement mechanisms of waste management policy. This mini-review paper describes the panorama of waste management practices in Botswana and provides information to competent authorities responsible for waste management and to researchers to develop and implement an effective waste management system. Waste management practices in Botswana are affected by: lack of effective implementation of national waste policy, fragmented tasks and overlapping mandates among relevant institutions; lack of clear guidelines on the responsibilities of the generators and public authorities and on the associated economic incentives; and lack of consistent and comprehensive solid waste management policies; lack of intent by decision-makers to prepare national waste management plans and systems, and design and implement an integrated sustainable municipal solid waste management system. Due to these challenges, there are concerns over the growing trend of the illegal dumping of waste, creating mini dumping sites all over the country, and such actions jeopardize the efforts of lobbying investors and tourism business. Recommendations for concerted efforts are made to support decision makers to re-organize a sustainable waste management system, and this paper provides a reference to other emerging economies in the region and the world.

[Medical wastes management: aspects of internal handling in the city of Marituba, Pará State, Brazil].

PubMed

Sales, Carla Cristina de Lima; Spolti, Gracieli Pâmela; Lopes, Maria do Socorro Bezerra; Lopes, David Franco

2009-01-01

Medical wastes offer a potential risk to public health and the environment before an inadequate management. This study aims to verify aspects of internal handling of medical wastes in the city of Marituba, Pará State. By means of questionnaires and field visits, a descriptive and observational study was performed in 13 health establishments in the city. The total volume of generated medical wastes was about 13,000 kg/week. There were deficiencies in many stages of the internal handling, for example the internal treatment that was performed in only one of the establishments, external storage made in 4 establishments and in precarious ways, among many others. Also, there were conformities as packing in adequate bags and containers as well as common waste separation. In general way, the federal norms were not accomplished and management of medical wastes in health establishments needs adequacy in every stage of the handling in order to control and reduce risks, decreasing the quantity of residues.

Management strategies on the industrialization road of state-of-the-art technologies for e-waste recycling: the case study of electrostatic separation--a review.

PubMed

Xue, Mianqiang; Li, Jia; Xu, Zhenming

2013-02-01

Electronic waste (e-waste) management is pressing as global production has increased significantly in the past few years and is rising continuously at a fast rate. Many countries are facing hazardous e-waste mountains, most of which are disposed of by backyard recyclers, creating serious threats to public health and ecosystems. Industrialization of state-of-the-art recycling technologies is imperative to enhance the comprehensive utilization of resources and to protect the environment. This article aims to provide an overview of management strategies solving the crucial problems during the process of industrialization. A typical case study of electrostatic separation for recycling waste printed circuit boards was discussed in terms of parameters optimization, materials flow control, noise assessment, risk assessment, economic evaluation and social benefits analysis. The comprehensive view provided by the review could be helpful to the progress of the e-waste recycling industry.

Berkeley Lab - Materials Sciences Division

Science.gov Websites

? Click Here! Resources for MSD Safety MSD Safety MSD's Integrated Safety Management Plan [PDF] Safety culture and policies at MSD MSD0010: Integrated Safety Management: Principles and Case Studies Calendar for MSD classes on Integrated Safety Management MSD0015 Handout - Waste Briefing Document [PDF] Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belsher, Jeremy D.; Pierson, Kayla L.; Gimpel, Rod F.

The Hanford site in southeast Washington contains approximately 207 million liters of radioactive and hazardous waste stored in 177 underground tanks. The U.S. Department of Energy's Office of River Protection is currently managing the Hanford waste treatment mission, which includes the storage, retrieval, treatment and disposal of the tank waste. Two recent studies, employing the modeling tools managed by the One System organization, have highlighted waste cleanup mission sensitivities. The Hanford Tank Waste Operations Simulator Sensitivity Study evaluated the impact that varying 21 different parameters had on the Hanford Tank Waste Operations Simulator model. It concluded that inaccuracies in themore » predicted phase partitioning of a few key components can result in significant changes in the waste treatment duration and in the amount of immobilized high-level waste that is produced. In addition, reducing the efficiency with which tank waste is retrieved and staged can increase mission duration. The 2012 WTP Tank Utilization Assessment concluded that flowsheet models need to include the latest low-activity waste glass algorithms or the waste treatment mission duration and the amount of low activity waste that is produced could be significantly underestimated. (authors)« less

Management of waste electrical and electronic equipment in Romania: A mini-review.

PubMed

Ciocoiu, Carmen Nadia; Colesca, Sofia Elena; Rudăreanu, Costin; Popescu, Maria-Loredana

2016-02-01

Around the world there are growing concerns for waste electrical and electronic equipment. This is motivated by the harmful effects of waste electrical and electronic equipment on the environment, but also by the perspectives of materials recovery. Differences between countries regarding waste electrical and electronic equipment management are notable in the European Union. Romania is among the countries that have made significant efforts to comply with European Union regulations, but failed reaching the collection target. The article presents a mini review of the waste electrical and electronic equipment management system in Romania, based on legislation and policy documents, statistical data, research studies and reports published by national and international organisations. The article debates subjects like legislative framework, the electrical and electronic equipment Romanian market, the waste electrical and electronic equipment collection system, waste electrical and electronic equipment processing and waste electrical and electronic equipment behaviour. The recast of the European directive brings new challenges to national authorities and to other stakeholders involved in the waste electrical and electronic equipment management. Considering the fact that Romania has managed a collection rate of roughly 1 kg capita(-1) in the last years, the new higher collection targets established by the waste electrical and electronic equipment Directive offer a serious challenge for the management system. Therefore, another aim of the article is to highlight the positive and negative aspects in the Romanian waste electrical and electronic equipment field, in order to identify the flows that should be corrected and the opportunities that could help improve this system to the point of meeting the European standards imposed by the European Directive. © The Author(s) 2015.

Energy implications of the thermal recovery of biodegradable municipal waste materials in the United Kingdom

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnley, Stephen, E-mail: s.j.burnley@open.ac.uk; Phillips, Rhiannon, E-mail: rhiannon.jones@environment-agency.gov.uk; Coleman, Terry, E-mail: terry.coleman@erm.com

2011-09-15

Highlights: > Energy balances were calculated for the thermal treatment of biodegradable wastes. > For wood and RDF, combustion in dedicated facilities was the best option. > For paper, garden and food wastes and mixed waste incineration was the best option. > For low moisture paper, gasification provided the optimum solution. - Abstract: Waste management policies and legislation in many developed countries call for a reduction in the quantity of biodegradable waste landfilled. Anaerobic digestion, combustion and gasification are options for managing biodegradable waste while generating renewable energy. However, very little research has been carried to establish the overall energymore » balance of the collection, preparation and energy recovery processes for different types of wastes. Without this information, it is impossible to determine the optimum method for managing a particular waste to recover renewable energy. In this study, energy balances were carried out for the thermal processing of food waste, garden waste, wood, waste paper and the non-recyclable fraction of municipal waste. For all of these wastes, combustion in dedicated facilities or incineration with the municipal waste stream was the most energy-advantageous option. However, we identified a lack of reliable information on the energy consumed in collecting individual wastes and preparing the wastes for thermal processing. There was also little reliable information on the performance and efficiency of anaerobic digestion and gasification facilities for waste.« less

Waste electrical and electronic equipment (WEEE) estimation: A case study of Ahvaz City, Iran.

PubMed

Alavi, Nadali; Shirmardi, Mohammad; Babaei, Aliakbar; Takdastan, Afshin; Bagheri, Nastaran

2015-03-01

The development of new technologies and the increasing consumption of electronic and electrical equipment have led to increased generation of e-waste in the municipal waste streams. This waste due to the presence of hazardous substances in its composition needs specific attention and management. The present study was carried out in Ahvaz metropolis using a survey method in 2011. For estimating the amount of waste electrical and electronic equipment (WEEE) generated, the "use and consumption" method was used. In order to determine the amounts of the electrical and electronic equipment that were used and their lifetime, and for investigating the current status of e-waste management in Ahvaz, an appropriate questionnaire was devised. In 2011, the total number of discarded electronic items was 2,157,742 units. According to the average weight of the equipment, the total generation of e-waste was 9952.25 metric tons per year and was 9.95 kg per capita per year. The highest e-waste generated was related to air conditioners, with 3125.36 metric tons per year, followed by the wastes from refrigerators and freezers, washing machines, and televisions. The wastes from desktop computers and laptops were 418 and 63 metric tons/year, respectively, and the corresponding values per capita were 0.42 and 0.063 kg, respectively. These results also showed that 10 tons fixed phones, 25 tons mobile phones, and by considering an average lifetime of 3 years for each lamp about 320 tons lamps were generated as e-waste in Ahvaz in the year 2011. Based on this study, currently there is not an integrated system for proper management of WEEE in Ahvaz, and this waste stream is collected and disposed of with other municipal waste. Some measures, including a specific collection system, recycling of valuable substances, and proper treatment and disposal, should be done about such waste. Ahvaz is one of the most important economic centers of Iran, and to the best of our knowledge, no study has been carried out to estimate the generation of waste electrical and electronic equipment (WEEE) in this city. Therefore, the authors estimated the generation of the WEEE by the "use and consumption" method. The results of this study can be useful not only for decision-making organizations of Ahvaz to manage and recycle this type of waste but also can be used as a method to estimate the generation of e-waste in different locations of the world, especially in places where the generation of such waste could be a risk to human health and the environment.

76 FR 55846 - Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon Dioxide...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-09

... 2050-AG60 Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon... hazardous waste management under the Resource Conservation and Recovery Act (RCRA) to conditionally exclude... and recordkeeping requirements. 40 CFR Part 261 Environmental protection, Hazardous waste, Solid waste...

Health concerns and hazardous waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yassi, A.; Weeks, J.; Kraut, A.

1990-01-01

This report discusses health effects of hazardous waste and emphasizes human health concerns related to establishing a hazardous waste management facility. The study reviewed world epidemiological and public health literature to identify cases of suspected or substantiated claims of public health impacts associated with hazardous waste management facilities and potential products or emissions from such facilities, and placed them into perspective, including possible routes and consequences of exposure, risk assessment, and the toxicity of selected organic and inorganic compounds.

Hazardous and toxic waste management in Botswana: practices and challenges.

PubMed

Mmereki, Daniel; Li, Baizhan; Meng, Liu

2014-12-01

Hazardous and toxic waste is a complex waste category because of its inherent chemical and physical characteristics. It demands for environmentally sound technologies and know-how as well as clean technologies that simultaneously manage and dispose it in an environmentally friendly way. Nevertheless, Botswana lacks a system covering all the critical steps from importation to final disposal or processing of hazardous and toxic waste owing to limited follow-up of the sources and types of hazardous and toxic waste, lack of modern and specialised treatment/disposal facilities, technical know-how, technically skilled manpower, funds and capabilities of local institutions to take lead in waste management. Therefore, because of a lack of an integrated system, there are challenges such as lack of cooperation among all the stakeholders about the safe management of hazardous and toxic waste. Furthermore, Botswana does not have a systematic regulatory framework regarding monitoring and hazardous and toxic waste management. In addition to the absence of a systematic regulatory framework, inadequate public awareness and dissemination of information about hazardous and toxic waste management, slower progress to phase-out persistent and bio-accumulative waste, and lack of reliable and accurate information on hazardous and toxic waste generation, sources and composition have caused critical challenges to effective hazardous and toxic waste management. It is, therefore, important to examine the status of hazardous and toxic waste as a waste stream in Botswana. By default; this mini-review article presents an overview of the current status of hazardous and toxic waste management and introduces the main challenges in hazardous and toxic waste management. Moreover, the article proposes the best applicable strategies to achieve effective hazardous and toxic waste management in the future. © The Author(s) 2014.

Biomedical waste management: study on the awareness and practice among healthcare workers in a tertiary teaching hospital.

PubMed

Joseph, L; Paul, H; Premkumar, J; Paul, R; Michael, J S

2015-01-01

Bio-medical waste has a higher potential of infection and injury to the healthcare worker, patient and the surrounding community. Awareness programmes on their proper handling and management to healthcare workers can prevent the spread of infectious diseases and epidemics. This study was conducted in a tertiary care hospital to assess the impact of training, audits and education/implementations from 2009 to 2012 on awareness and practice of biomedical waste segregation. Our study reveals focused training, strict supervision, daily surveillance, audits inspections, involvement of hospital administrators and regular appraisals are essential to optimise the segregation of biomedical waste.

Waste management outlook for mountain regions: Sources and solutions.

PubMed

Semernya, Larisa; Ramola, Aditi; Alfthan, Björn; Giacovelli, Claudia

2017-09-01

Following the release of the global waste management outlook in 2015, the United Nations Environment Programme (UN Environment), through its International Environmental Technology Centre, is elaborating a series of region-specific and thematic waste management outlooks that provide policy recommendations and solutions based on current practices in developing and developed countries. The Waste Management Outlook for Mountain Regions is the first report in this series. Mountain regions present unique challenges to waste management; while remoteness is often associated with costly and difficult transport of waste, the potential impact of waste pollutants is higher owing to the steep terrain and rivers transporting waste downstream. The Outlook shows that waste management in mountain regions is a cross-sectoral issue of global concern that deserves immediate attention. Noting that there is no 'one solution fits all', there is a need for a more landscape-type specific and regional research on waste management, the enhancement of policy and regulatory frameworks, and increased stakeholder engagement and awareness to achieve sustainable waste management in mountain areas. This short communication provides an overview of the key findings of the Outlook and highlights aspects that need further research. These are grouped per source of waste: Mountain communities, tourism, and mining. Issues such as waste crime, plastic pollution, and the linkages between exposure to natural disasters and waste are also presented.

Understanding the perceptions, roles and interactions of stakeholder networks managing health-care waste: A case study of the Gaza Strip

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caniato, M., E-mail: marcocaniato@gmail.com; Tudor, T.; Vaccari, M.

Highlights: • We systematically review scientific literature about health-care waste management. • We identify and discuss gaps, trends, efforts, and key-factors. • We suggest areas for improvement and best practices reported in literature. • We include recommendations for policy makers, practitioners and researchers. • We promote a holistic and harmonized approach to health-care waste management. - Abstract: The sustainable management of waste requires a holistic approach involving a range of stakeholders. What can often be difficult is to understand the manner in which different types of stakeholder networks are composed and work, and how best to enhance their effectiveness. Usingmore » social network analysis and stakeholder analysis of healthcare waste management stakeholders in the case study region of the Gaza Strip, this study aimed to understand and examine the manner in which the networks functioned. The Ministry of Health was found to be the most important stakeholder, followed by municipalities and solid waste management councils. Some international agencies were also mentioned, with specific roles, while other local institutions had a limited influence. Finally while health-care facilities had a strong interest in waste management, they were generally poorly informed and had limited links to each other. The manner in which the networks operated was complicated and influenced by differences in perception, sharing of information, access to finance and levels of awareness. The lack of a clear legal framework generated various mistakes about roles and responsibilities in the system, and evidently regulation was not an effective driver for improvement. Finally stakeholders had different priorities according to the waste management issues they were involved with, however segregation at the source was identified as a key requirement by most. Areas for improving the effectiveness of the networks are suggested. The analysis utilized an innovative methodology, which involved a large number of stakeholders. Such an approach served to raise interest and awareness at different levels (public authorities, health providers, supporting actors, others), stimulate the discussion about the adoption of specific policies, and identify the effective way forward.« less

Environmental-Economic Assessment Of Generation, Flow And Efficiency Of Use Of Production And Consumption Waste

NASA Astrophysics Data System (ADS)

Mikhailov, V. G.; Golofastova, N. N.; Galanina, T. V.; Koroleva, T. G.; Mikhailova, Ya S.

2017-01-01

The article deals with the issues of environmental and economic analysis of industrial and economic activities of an enterprise to assess the generation, flow and efficiency of production and consumption waste. The purpose of research is the analysis and the development of theoretical propositions for the functioning of the system of environmental and economic indicators for the effective management of production and consumption waste in the enterprise. The analysis of the existing systems of environmental and economic indicators taking into consideration the industry characteristics and the types of negative impacts is carried out. The main result of the study is the development of the system of environmental and economic indicators of production and consumption waste, adapted to the modern requirements. The results of the study can be recommended to support the effective management decision-making concerning waste management and the establishment of appropriate infrastructure.

Dynamic analysis for solid waste management systems: an inexact multistage integer programming approach.

PubMed

Li, Yongping; Huang, Guohe

2009-03-01

In this study, a dynamic analysis approach based on an inexact multistage integer programming (IMIP) model is developed for supporting municipal solid waste (MSW) management under uncertainty. Techniques of interval-parameter programming and multistage stochastic programming are incorporated within an integer-programming framework. The developed IMIP can deal with uncertainties expressed as probability distributions and interval numbers, and can reflect the dynamics in terms of decisions for waste-flow allocation and facility-capacity expansion over a multistage context. Moreover, the IMIP can be used for analyzing various policy scenarios that are associated with different levels of economic consequences. The developed method is applied to a case study of long-term waste-management planning. The results indicate that reasonable solutions have been generated for binary and continuous variables. They can help generate desired decisions of system-capacity expansion and waste-flow allocation with a minimized system cost and maximized system reliability.

Characterization of industrial waste from a natural gas distribution company and management strategies: a case study of the East Azerbaijan Gas Company (Iran).

PubMed

Taghipour, Hassan; Aslhashemi, Ahmad; Assadi, Mohammad; Khodaei, Firoz; Mardangahi, Baharak; Mosaferi, Mohammad; Roshani, Babak

2012-10-01

Although a fundamental prerequisite for the successful implementation of any waste management plan is the availability of sufficient and accurate data, there are few available studies regarding the characterization and management of gas distribution company waste (GDCW). This study aimed to characterize the industrial waste generated by the East Azerbaijan Gas Distribution Company (EAGDC) and to present environmental management strategies. The EAGDC serves 57 cities and 821 villages with a total population of more than 2.5 million as well as numerous industrial units. The methodology of this study was based on a checklist of data collected from each zone of the company, site visits (observation), and quantity and quality analysis according to the formal data available from different zones. The results indicate that more than 35 different kinds of industrial solid waste are generated in different industrial installations. The most important types of generated waste include empty barrels (including mercaptans, diesel fuel, deionized waters and oil), faulty gas meters and regulators, a variety of industrial oils, sleeves, filter elements and faulty pipes, valves and fittings. The results indicated that, currently, GDCW is generally handled and disposed of with domestic waste, deposited in companies' installation yards and stores or, sometimes, recycled through non-scientific approaches that can create health risks to the public and the environment, even though most of the GDCW was determined to be recyclable or reusable materials. This study concludes that gas distribution companies must pay more attention to source reduction, recycling and reusing of waste to preserve natural resources, landfill space and the environment.

40 CFR 62.14585 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false When must I submit my waste management... Commenced Construction On or Before November 30, 1999 Waste Management Plan § 62.14585 When must I submit my waste management plan? You must submit a waste management plan no later than April 5, 2004. ...

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What is a waste management plan? 60... Which Modification or Reconstruction Is Commenced on or After June 1, 2001 Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both...

40 CFR 60.3011 - When must I submit my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false When must I submit my waste management... Model Rule-Waste Management Plan § 60.3011 When must I submit my waste management plan? You must submit a waste management plan no later than 60 days following the initial performance test as specified in...

40 CFR 62.14585 - When must I submit my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false When must I submit my waste management... Commenced Construction On or Before November 30, 1999 Waste Management Plan § 62.14585 When must I submit my waste management plan? You must submit a waste management plan no later than April 5, 2004. ...

40 CFR 62.14580 - What is a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false What is a waste management plan? 62... Construction On or Before November 30, 1999 Waste Management Plan § 62.14580 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility and the methods used to...

40 CFR 60.3011 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management... Model Rule-Waste Management Plan § 60.3011 When must I submit my waste management plan? You must submit a waste management plan no later than 60 days following the initial performance test as specified in...

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false What is a waste management plan? 60... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false When must I submit my waste management... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing...

40 CFR 62.14585 - When must I submit my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false When must I submit my waste management... Commenced Construction On or Before November 30, 1999 Waste Management Plan § 62.14585 When must I submit my waste management plan? You must submit a waste management plan no later than April 5, 2004. ...

40 CFR 60.3011 - When must I submit my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false When must I submit my waste management... Model Rule-Waste Management Plan § 60.3011 When must I submit my waste management plan? You must submit a waste management plan no later than 60 days following the initial performance test as specified in...

40 CFR 60.2055 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What is a waste management plan? 60... Which Modification or Reconstruction Is Commenced on or After June 1, 2001 Waste Management Plan § 60.2055 What is a waste management plan? A waste management plan is a written plan that identifies both...

40 CFR 60.2900 - When must I submit my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false When must I submit my waste management... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2900 When must I submit my waste management plan? You must submit a waste management plan prior to commencing...

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false What is a waste management plan? 60... Modification or Reconstruction is Commenced on or After June 16, 2006 Waste Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility...

40 CFR 62.14585 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false When must I submit my waste management... Commenced Construction On or Before November 30, 1999 Waste Management Plan § 62.14585 When must I submit my waste management plan? You must submit a waste management plan no later than April 5, 2004. ...

40 CFR 62.14580 - What is a waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false What is a waste management plan? 62... Construction On or Before November 30, 1999 Waste Management Plan § 62.14580 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility and the methods used to...

40 CFR 60.3011 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management... Model Rule-Waste Management Plan § 60.3011 When must I submit my waste management plan? You must submit a waste management plan no later than 60 days following the initial performance test as specified in...

40 CFR 62.14580 - What is a waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false What is a waste management plan? 62... Construction On or Before November 30, 1999 Waste Management Plan § 62.14580 What is a waste management plan? A waste management plan is a written plan that identifies both the feasibility and the methods used to...

Municipal solid-waste management in Istanbul.

PubMed

Kanat, Gurdal

2010-01-01

Istanbul, with a population of around 13 million people, is located between Europe and Asia and is the biggest city in Turkey. Metropolitan Istanbul produces about 14,000 tons of solid waste per day. The aim of this study was to assess the situation of municipal solid-waste (MSW) management in Istanbul. This was achieved by reviewing the quantity and composition of waste produced in Istanbul. Current requirements and challenges in relation to the optimization of Istanbul's MSW collection and management system are also discussed, and several suggestions for solving the problems identified are presented. The recovery of solid waste from the landfills, as well as the amounts of landfill-generated biogas and electricity, were evaluated. In recent years, MSW management in Istanbul has improved because of strong governance and institutional involvement. However, efforts directed toward applied research are still required to enable better waste management. These efforts will greatly support decision making on the part of municipal authorities. There remains a great need to reduce the volume of MSW in Istanbul. 2010 Elsevier Ltd. All rights reserved.

Reclamation of landfills and dumps of municipal solid waste in a energy efficient waste management system: methodology and practice

NASA Astrophysics Data System (ADS)

Orlova, Tatyana; Melnichuk, Aleksandr; Klimenko, Kseniya; Vitvitskaya, Valentina; Popovych, Valentina; Dunaieva, Ielizaveta; Terleev, Vitaly; Nikonorov, Aleksandr; Togo, Issa; Volkova, Yulia; Mirschel, Wilfried; Garmanov, Vitaly

2017-10-01

The article considers the methodological and practical aspects of reclamation of landfills and dumps of municipal solid waste in a waste management system. The general tendencies of system development in the context of elements of the international concept of waste hierarchy are analyzed. Statistics of the formation and burial of domestic waste indicate a strategic non-alternative to the rejection of landfill technologies in favor of environmentally, energy efficient and economically expedient ways of utilization of municipal waste as a world trend. Practical approaches to the study of territories on which there are dumps and landfills are considered to justify the design solutions for reclamation.

Adherence to Healthcare Waste Management Guidelines among Nurses and Waste Handlers in Thika Sub-county- Kenya.

PubMed

Njue, P Mwaniki; Cheboi, K Solomon; Shadrak, Oiye

2015-10-01

Despite the set guidelines on Healthcare Waste Management in Kenya, mixing of different categories of waste, crude dumping and poor incineration are still a common phenomenon in public health facilities in Thika Subcounty, Kenya. Thika Subcounty generates 560 Kilograms of healthcare waste daily, which is risk to the many patients (admission rate of 26%). This may pose a potential environmental risk and be a source of disease diffusion. This research explored the adherence to healthcare waste management waste guidelines in health care facilities among the nurses and waste handlers. This was a cross sectional survey in which mixed methods were applied. A census and proportionate random sampling method were used. Quantitative data was analyzed using Statistical Package for Social Science (SPSS) version 20.0, while qualitative data was analyzed manually into themes. Full adherence to the seven waste disposal guidelines was low (16.3%). Knowledge on waste segregation, waste separation then disposal and means of transports were statistically significant in relation to adherence. The type of incinerator and burning status, protection maintenance and supply of adequate waste bins were also important to adherence level. Adherence level was low (16.3%,) and insignificantly different among nurses and waste handlers. From this finding, compliance remains a key challenge. Strategies targeted at contextualizing waste regulations and guidelines into local settings are necessary and important. Policy makers may design and implement standard incinerators across all the health facilities. This study is not exhaustive; therefore, it is necessary to carry out a study linking poor treatment and disposal of clinical waste to purported health outcomes in Kenya.

National information network and database system of hazardous waste management in China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma Hongchang

1996-12-31

Industries in China generate large volumes of hazardous waste, which makes it essential for the nation to pay more attention to hazardous waste management. National laws and regulations, waste surveys, and manifest tracking and permission systems have been initiated. Some centralized hazardous waste disposal facilities are under construction. China`s National Environmental Protection Agency (NEPA) has also obtained valuable information on hazardous waste management from developed countries. To effectively share this information with local environmental protection bureaus, NEPA developed a national information network and database system for hazardous waste management. This information network will have such functions as information collection, inquiry,more » and connection. The long-term objective is to establish and develop a national and local hazardous waste management information network. This network will significantly help decision makers and researchers because it will be easy to obtain information (e.g., experiences of developed countries in hazardous waste management) to enhance hazardous waste management in China. The information network consists of five parts: technology consulting, import-export management, regulation inquiry, waste survey, and literature inquiry.« less

Domestic food practices: A study of food management behaviors and the role of food preparation planning in reducing waste.

PubMed

Romani, Simona; Grappi, Silvia; Bagozzi, Richard P; Barone, Ada Maria

2018-02-01

Recent research has started to show the key role of daily food provision practices in affecting household food waste. Building on and extending these previous contributions, the objective of this paper is to investigate how individuals' everyday practices regarding food (e.g., shopping, cooking, eating, etc.) lead to food waste, and how policy makers and the food industry can implement effective strategies to influence such practices and ultimately help consumers reduce food waste. The research performs three Studies; a critical incident qualitative study (Study 1; N = 514) and a quantitative, survey-based study (Study 2; N = 456) to identify and examine relevant food management behaviors associated with domestic waste. Lastly, findings from a field experiment (Study 3; N = 210) suggest that a specific educational intervention, directed at increasing consumers' perceived skills related to food preparation planning behaviors, reduces domestic food waste. Implications of the research for policy makers and the food industry are discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Problems of solid waste management on Mount Kilimanjaro: a challenge to tourism.

PubMed

Kaseva, Mengiseny E; Moirana, Josia L

2010-08-01

We report on the findings of a study on the problems of solid waste management (SWM) on Mountain Kilimanjaro (MK) which is located within Kilimanjaro National Park (KINAPA) in Northern Tanzania. The study was prompted by the fact that flourishing tourism on the mountain over the years has resulted in an increase in the tonnage of solid waste (SW) generated, posing serious challenges in its collection and disposal. The methodology employed in this study included physical observations and questionnaire surveys, as well as waste sorting and weighing to quantify and characterize waste loads collected from each tourist route station covered in this study. On the basis of the established SW generation rate (0.6 kg ca(-1) day(-1)) a total amount of SW generated was estimated to range from about 87 tones (in 2003) to 125 tones (in 2006). An improvement in SW collection from 64% in 2003 to 94% in 2006 was also noted. This improvement can be attributed to the trash-in-trash-out (TITO) system of SW collection which is currently practiced by the management of KINAPA for SWM on MK. The study also highlights potential environmental pollution including air pollution from open burning and pit disposal of SW. Based on average percentage values of waste components and the estimated quantity of waste generated, it was established that the total waste quantum contains about 34% of recyclables. The study recommends that resource recovery and conservation measures through waste recycling and re-use be instituted as one of the options for sustainable SWM on MK.

Exploring residents' attitudes and willingness to pay for solid waste management in Macau.

PubMed

Song, Qingbin; Wang, Zhishi; Li, Jinhui

2016-08-01

Increasing public attention has been brought to bear on the solid waste management in Macau, due to the continually increasing generation of amount and the limited space. In this study, we discussed residents' attitudes and willingness to pay (WTP) for solid waste management through a questionnaire survey. The results showed that Macau residents owned a relatively high environmental awareness. In regard to Macau environmental quality, most respondents (92.4 %) expressed their satisfactions on the current situation. About 50.2 % respondents thought that the solid waste pollution in Macau should be paid more attention than the other three environmental pollution ways (air pollution, water pollution, and soil pollution). The survey data revealed the positive attitudes toward source separation in Macau. About 95.7 % respondents were willing to sort the solid waste at home, if the government required them to do it. In addition, for the question on how to improve the solid waste issues in Macau, "Enhancing residents' environmental awareness" was considered as the most effective method, accounting for about 38.5 % respondents. In our study, most respondents (85.4 %) also provided positive answers to the questions about WTP. Using the logistic regression method, these survey results support the hypothesis that the probability of the respondents' saying "yes" to the WTP question increases with education level. The monthly mean WTP was 38.5 MOP per household, and the annual WTP was approximately 79.7 million MOP for all of Macau. The results of our study can help managers develop more effective environmental management policies for solid waste disposal.

Environmental and health impacts of household solid waste handling and disposal practices in third world cities: the case of the Accra Metropolitan Area, Ghana.

PubMed

Boadi, Kwasi Owusu; Kuitunen, Markku

2005-11-01

Inadequate provision of solid waste management facilities in Third World cities results in indiscriminate disposal and unsanitary environments, which threatens the health of urban residents. The study reported here examined household-level waste management and disposal practices in the Accra Metropolitan Area, Ghana. The residents of Accra currently generate large amounts of solid waste, beyond the management capabilities of the existing waste management system. Because the solid waste infrastructure is inadequate, over 80 percent of the population do not have home collection services. Only 13.5 percent of respondents are served with door-to-door collection of solid waste, while the rest dispose of their waste at communal collection points, in open spaces, and in waterways. The majority of households store their waste in open containers and plastic bags in the home. Waste storage in the home is associated with the presence of houseflies in the kitchen (r = .17, p < .0001). The presence of houseflies in the kitchen during cooking is correlated with the incidence of childhood diarrhea (r = .36, p < .0001). Inadequate solid waste facilities result in indiscriminate burning and burying of solid waste. There is an association between waste burning and the incidence of respiratory health symptoms among adults (r = .25, p < .0001) and children (r = .22, p < .05). Poor handling and disposal of waste are major causes of environmental pollution, which creates breeding grounds for pathogenic organisms, and the spread of infectious diseases. Improving access to solid waste collection facilities and services will help achieve sound environmental health in Accra.

GIS-based planning system for managing the flow of construction and demolition waste in Brazil.

PubMed

Paz, Diogo Henrique Fernandes da; Lafayette, Kalinny Patrícia Vaz; Sobral, Maria do Carmo

2018-05-01

The objective of this article was to plan a network for municipal management of construction and demolition waste in Brazil with the assistance of a geographic information system, using the city of Recife as a case study. The methodology was carried out in three stages. The first was to map the illegal construction and demolition of waste disposal points across Recife and classify the waste according to its recyclability. In sequence, a method for indicating suitable areas for installation of voluntary delivery points, for small waste generators, are presented. Finally, a method for indicating suitable areas for the installation of trans-shipment and waste sorting areas, developed for large generators, is presented. The results show that a geographic information system is an essential tool in the planning of municipal construction and demolition waste management, in order to facilitate the spatial analysis and control the generation, sorting, collection, transportation, and final destination of construction and demolition waste, increasing the rate of recovery and recycling of materials.

Hazardous Waste: Learn the Basics of Hazardous Waste

MedlinePlus

... to set up a framework for the proper management of hazardous waste. Need More Information on Hazardous Waste? The RCRA Orientation Manual provides ... facility management standards, specific provisions governing hazardous waste management units ... information on the final steps in EPA’s hazardous waste ...

Modular life cycle assessment of municipal solid waste management.

PubMed

Haupt, M; Kägi, T; Hellweg, S

2018-05-31

Life cycle assessment (LCA) is commonly applied to examine the environmental performance of waste management systems. The system boundaries are, however, often limited to either one tonne of material or to specific waste treatments and are, therefore, lacking a systems perspective. Here, a framework is proposed to assess complete waste management systems based on actual waste flows, assessed with a detailed material flow analysis (MFA) in a modular MFA/LCA approach. The transformation of the MFA into a product-process-matrix facilitates a direct link between MFA and LCA, therefore allowing for the assessment of variations in flows. To allow for an up-to-date and geographically specific assessment, 190 LCA modules were set up based on primary industrial data and the ecoinvent database. The LCA modules show where there have been improvements in different recycling processes over the past years (e.g. for paper recycling) and highlight that, from an environmental perspective, closed-loop recycling is not always preferable to open-loop recycling. In a case study, the Swiss municipal solid waste management system, of which there is already a detailed MFA, was modeled using the new LCA modules and applying the modular MFA/LCA approach. Five different mass flow distribution scenarios for the Swiss municipal solid waste management system were assessed to show the environmental impact of political measures and to test the sensitivity of the results to key parameters. The results of the case study highlight the importance of the dominant fractions in the overall environmental impacts assessment; while the metal fraction has the highest impact on a per kilogram basis, paper, cardboard, glass and mixed municipal solid waste were found to dominate the environmental impacts of the Swiss waste management system due to their mass. The scenarios also highlight the importance of the energy efficiency of municipal solid waste incineration plants and the credits from material substitution as key variables. In countries with advanced waste management systems such as Switzerland, there is limited improvement potential with further increases in recycling rates. In these cases, the focus of political measures should be laid on (i) the utilization of secondary materials in applications where they replace high-impact primary production, and (ii) an increased recovery of energy in waste-to-energy plants. Copyright © 2018. Published by Elsevier Ltd.

Making waste management public (or falling back to sleep)

PubMed Central

Lougheed, Scott; Rowe, R Kerry; Kuyvenhoven, Cassandra

2014-01-01

Human-produced waste is a major environmental concern, with communities considering various waste management practices, such as increased recycling, landfilling, incineration, and waste-to-energy technologies. This article is concerned with how and why publics assemble around waste management issues. In particular, we explore Noortje Marres and Bruno Latour’s theory that publics do not exist prior to issues but rather assemble around objects, and through these assemblages, objects become matters of concern that sometimes become political. The article addresses this theory of making things public through a study of a small city in Ontario, Canada, whose landfill is closed and waste diversion options are saturated, and that faces unsustainable costs in shipping its waste to the United States, China, and other regions. The city’s officials are undertaking a cost–benefit assessment to determine the efficacy of siting a new landfill or other waste management facility. We are interested in emphasizing the complexity of making (or not making) landfills public, by exploring an object in action, where members of the public may or may not assemble, waste may or may not be made into an issue, and waste is sufficiently routinized that it is not typically transformed from an object to an issue. We hope to demonstrate Latour’s third and fifth senses of politics best account for waste management’s trajectory as a persistent yet inconsistent matter of public concern. PMID:25051590

The S-curve for forecasting waste generation in construction projects.

PubMed

Lu, Weisheng; Peng, Yi; Chen, Xi; Skitmore, Martin; Zhang, Xiaoling

2016-10-01

Forecasting construction waste generation is the yardstick of any effort by policy-makers, researchers, practitioners and the like to manage construction and demolition (C&D) waste. This paper develops and tests an S-curve model to indicate accumulative waste generation as a project progresses. Using 37,148 disposal records generated from 138 building projects in Hong Kong in four consecutive years from January 2011 to June 2015, a wide range of potential S-curve models are examined, and as a result, the formula that best fits the historical data set is found. The S-curve model is then further linked to project characteristics using artificial neural networks (ANNs) so that it can be used to forecast waste generation in future construction projects. It was found that, among the S-curve models, cumulative logistic distribution is the best formula to fit the historical data. Meanwhile, contract sum, location, public-private nature, and duration can be used to forecast construction waste generation. The study provides contractors with not only an S-curve model to forecast overall waste generation before a project commences, but also with a detailed baseline to benchmark and manage waste during the course of construction. The major contribution of this paper is to the body of knowledge in the field of construction waste generation forecasting. By examining it with an S-curve model, the study elevates construction waste management to a level equivalent to project cost management where the model has already been readily accepted as a standard tool. Copyright © 2016 Elsevier Ltd. All rights reserved.

A system dynamic modeling approach for evaluating municipal solid waste generation, landfill capacity and related cost management issues.

PubMed

Kollikkathara, Naushad; Feng, Huan; Yu, Danlin

2010-11-01

As planning for sustainable municipal solid waste management has to address several inter-connected issues such as landfill capacity, environmental impacts and financial expenditure, it becomes increasingly necessary to understand the dynamic nature of their interactions. A system dynamics approach designed here attempts to address some of these issues by fitting a model framework for Newark urban region in the US, and running a forecast simulation. The dynamic system developed in this study incorporates the complexity of the waste generation and management process to some extent which is achieved through a combination of simpler sub-processes that are linked together to form a whole. The impact of decision options on the generation of waste in the city, on the remaining landfill capacity of the state, and on the economic cost or benefit actualized by different waste processing options are explored through this approach, providing valuable insights into the urban waste-management process. Copyright © 2010 Elsevier Ltd. All rights reserved.

A system dynamic modeling approach for evaluating municipal solid waste generation, landfill capacity and related cost management issues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kollikkathara, Naushad, E-mail: naushadkp@gmail.co; Feng Huan; Yu Danlin

2010-11-15

As planning for sustainable municipal solid waste management has to address several inter-connected issues such as landfill capacity, environmental impacts and financial expenditure, it becomes increasingly necessary to understand the dynamic nature of their interactions. A system dynamics approach designed here attempts to address some of these issues by fitting a model framework for Newark urban region in the US, and running a forecast simulation. The dynamic system developed in this study incorporates the complexity of the waste generation and management process to some extent which is achieved through a combination of simpler sub-processes that are linked together to formmore » a whole. The impact of decision options on the generation of waste in the city, on the remaining landfill capacity of the state, and on the economic cost or benefit actualized by different waste processing options are explored through this approach, providing valuable insights into the urban waste-management process.« less

Towards Zero Waste in emerging countries - A South African experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matete, Ntlibi; Trois, Cristina

2008-07-01

The aim of this paper is to describe the optimisation of Waste Minimisation/Zero Waste strategies into an already established integrated waste management system and to present a Zero Waste model for post-consumer waste for urban communities in South Africa. The research was undertaken towards the fulfilment of the goals of the Polokwane Declaration on Waste Management , which has set as its target the reduction of waste generation and disposal by 50% and 25%, respectively, by 2012 and the development of a plan for Zero Waste by 2022. Two communities, adjacent to the Mariannhill Landfill site in Durban, were selectedmore » as a case study for a comparative analysis of formal and informal settlements. Since the waste generated from these two communities is disposed of at the Mariannhill landfill, the impact of Zero Waste on landfill volumes could be readily assessed. A Zero Waste scheme, based on costs and landfill airspace savings, was proposed for the area. The case study demonstrates that waste minimisation schemes can be introduced into urban areas, in emerging countries, with differing levels of service and that Zero Waste models are appropriate to urban areas in South Africa.« less

Conflicting Expertise and Uncertainty: Quality Assurance in High-Level Radioactive Waste Management.

ERIC Educational Resources Information Center

Fitzgerald, Michael R.; McCabe, Amy Snyder

1991-01-01

Dynamics of a large, expensive, and controversial surface and underground evaluation of a radioactive waste management program at the Yucca Mountain power plant are reviewed. The use of private contractors in the quality assurance study complicates the evaluation. This case study illustrates high stakes evaluation problems. (SLD)

Comparing Pedagogies for Plastic Waste Management at University Level

ERIC Educational Resources Information Center

Yeung, Siu-Kit; So, Wing-Mui Winnie; Cheng, Nga-Yee Irene; Cheung, Tsz-Yan; Chow, Cheuk-Fai

2017-01-01

Purpose: This paper aims to compare the learning outcomes of gaming simulation and guided inquiry in sustainability education on plastic waste management. The current study targets the identification of success factors in these teaching approaches. Design/methodology/approach: This study used a quasi-experimental design with undergraduate…

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 60.35e - Waste management guidelines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Waste management guidelines. 60.35e... Hospital/Medical/Infectious Waste Incinerators § 60.35e Waste management guidelines. For approval, a State plan shall include the requirements for a waste management plan at least as protective as those...

40 CFR 62.14590 - What should I include in my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... in my waste management plan? A waste management plan must include consideration of the reduction or separation of waste-stream elements such as paper, cardboard, plastics, glass, batteries, or metals; or the... waste management measures already in place, the costs of additional measures, the emissions reductions...

E-waste management in India: A mini-review.

PubMed

Awasthi, Abhishek Kumar; Wang, Mengmeng; Wang, Zhishi; Awasthi, Mrigendra Kumar; Li, Jinhui

2018-05-01

Environmental deterioration and health risk due to improper e-waste management has become a serious issue in India. The major portion of e-waste reaches an unorganized e-waste recycling sector and is then treated by using crude methods. This review article presents a brief highlight on e-waste management status, legislation, and technology uses in India. The present e-waste management needs to be more focused on environmentally sound management, by more active support from all the participants involved in the e-waste flow chain in India.

Toward zero waste: Composting and recycling for sustainable venue based events

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hottle, Troy A., E-mail: troy.hottle@asu.edu; Bilec, Melissa M., E-mail: mbilec@pitt.edu; Brown, Nicholas R., E-mail: nick.brown@asu.edu

Highlights: • Venues have billions of customers per year contributing to waste generation. • Waste audits of four university baseball games were conducted to assess venue waste. • Seven scenarios including composting were modeled using EPA’s WARM. • Findings demonstrate tradeoffs between emissions, energy, and landfill avoidance. • Sustainability of handling depends on efficacy of collection and treatment impacts. - Abstract: This study evaluated seven different waste management strategies for venue-based events and characterized the impacts of event waste management via waste audits and the Waste Reduction Model (WARM). The seven waste management scenarios included traditional waste handling methods (e.g.more » recycle and landfill) and management of the waste stream via composting, including purchasing where only compostable food service items were used during the events. Waste audits were conducted at four Arizona State University (ASU) baseball games, including a three game series. The findings demonstrate a tradeoff among CO{sub 2} equivalent emissions, energy use, and landfill diversion rates. Of the seven waste management scenarios assessed, the recycling scenarios provide the greatest reductions in CO{sub 2} eq. emissions and energy use because of the retention of high value materials but are compounded by the difficulty in managing a two or three bin collection system. The compost only scenario achieves complete landfill diversion but does not perform as well with respect to CO{sub 2} eq. emissions or energy. The three game series was used to test the impact of staffed bins on contamination rates; the first game served as a baseline, the second game employed staffed bins, and the third game had non staffed bins to determine the effect of staffing on contamination rates. Contamination rates in both the recycling and compost bins were tracked throughout the series. Contamination rates were reduced from 34% in the first game to 11% on the second night (with the staffed bins) and 23% contamination rates at the third game.« less

FSILP: fuzzy-stochastic-interval linear programming for supporting municipal solid waste management.

PubMed

Li, Pu; Chen, Bing

2011-04-01

Although many studies on municipal solid waste management (MSW management) were conducted under uncertain conditions of fuzzy, stochastic, and interval coexistence, the solution to the conventional linear programming problems of integrating fuzzy method with the other two was inefficient. In this study, a fuzzy-stochastic-interval linear programming (FSILP) method is developed by integrating Nguyen's method with conventional linear programming for supporting municipal solid waste management. The Nguyen's method was used to convert the fuzzy and fuzzy-stochastic linear programming problems into the conventional linear programs, by measuring the attainment values of fuzzy numbers and/or fuzzy random variables, as well as superiority and inferiority between triangular fuzzy numbers/triangular fuzzy-stochastic variables. The developed method can effectively tackle uncertainties described in terms of probability density functions, fuzzy membership functions, and discrete intervals. Moreover, the method can also improve upon the conventional interval fuzzy programming and two-stage stochastic programming approaches, with advantageous capabilities that are easily achieved with fewer constraints and significantly reduces consumption time. The developed model was applied to a case study of municipal solid waste management system in a city. The results indicated that reasonable solutions had been generated. The solution can help quantify the relationship between the change of system cost and the uncertainties, which could support further analysis of tradeoffs between the waste management cost and the system failure risk. Copyright © 2010 Elsevier Ltd. All rights reserved.

Solid waste production and its management in dental clinics in Gorgan, northern Iran.

PubMed

Nabizadeh, R; Faraji, H; Mohammadi, A A

2014-10-01

Waste produced in dental clinics has been the topic of investigations for many years. These waste materials have important health impacts and are hazardous to humans and the environment. To investigating solid waste production and its management in dental clinics in Gorgan, northern Iran. In this cross-sectional study, 45 of 143 public dental practices and 5 of 25 private dental practices were selected and studied. From each clinic, 3 samples were taken and analyzed at the end of successive working days (Tuesday and Wednesday). Samples were manually sorted into 50 components. The measured components were then classified on the basis of their characteristics, hazard potentials, and WHO classification. The total annual amount of dental waste produced in public and private dental practices in Gorgan was 12 015.1 and 3135.0 kg, respectively. Production percentages of infectious, domestic, chemical and pharmaceutical, and toxic waste in public dental practices were 38.4%, 33.7%, 6.6%, and 0.6%, respectively. The percentages for private practices were 8.7%, 10.6%, 1.1%, and 0.1%, respectively. Dental waste management in Gorgan is inadequate; dental waste is not properly segregated, collected, and disposed, as demanded by the WHO. Employees in dentist offices must be trained in correct handling of waste products and the associated risks.

Pyrolysis and co-composting of municipal organic waste in Bangladesh: A quantitative estimate of recyclable nutrients, greenhouse gas emissions, and economic benefits.

PubMed

Mia, Shamim; Uddin, Md Ektear; Kader, Md Abdul; Ahsan, Amimul; Mannan, M A; Hossain, Mohammad Monjur; Solaiman, Zakaria M

2018-05-01

Waste causes environmental pollution and greenhouse gas (GHG) emissions when it is not managed sustainably. In Bangladesh, municipal organic waste (MOW) is partially collected and landfilled. Thus, it causes deterioration of the environment urging a recycle-oriented waste management system. In this study, we propose a waste management system through pyrolysis of selective MOW for biochar production and composting of the remainder with biochar as an additive. We estimated the carbon (C), nitrogen (N), phosphorus (P) and potassium (K) recycling potentials in the new techniques of waste management. Waste generation of a city was calculated using population density and per capita waste generation rate (PWGR). Two indicators of economic development, i.e., gross domestic product (GDP) and per capita gross national income (GNI) were used to adopt PWGR with a projected contribution of 5-20% to waste generation. The projected PWGR was then validated with a survey. The waste generation from urban areas of Bangladesh in 2016 was estimated between 15,507 and 15,888 t day -1 with a large share (∼75%) of organic waste. Adoption of the proposed system could produce 3936 t day -1 biochar blended compost with an annual return of US $210 million in 2016 while it could reduce GHG emission substantially (-503 CO 2 e t -1 municipal waste). Moreover, the proposed system would able to recover ∼46%, 54%, 54% and 61% of total C, N, P and K content in the initial waste, respectively. We also provide a projection of waste generation and nutrient recycling potentials for the year 2035. The proposed method could be a self-sustaining policy option for waste management as it would generate ∼US$51 from each tonne of waste. Moreover, a significant amount of nutrients can be recycled to agriculture while contributing to the reduction in environmental pollution and GHG emission. Copyright © 2018 Elsevier Ltd. All rights reserved.

40 CFR 62.14432 - When must my waste management plan be completed?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false When must my waste management plan be... Before June 20, 1996 Waste Management Plan § 62.14432 When must my waste management plan be completed? As specified in §§ 62.14463 and 62.14464, you must submit your waste management plan with your initial report...

40 CFR 62.14432 - When must my waste management plan be completed?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false When must my waste management plan be... Before June 20, 1996 Waste Management Plan § 62.14432 When must my waste management plan be completed? As specified in §§ 62.14463 and 62.14464, you must submit your waste management plan with your initial report...

40 CFR 62.14432 - When must my waste management plan be completed?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false When must my waste management plan be... Before December 1, 2008 Waste Management Plan § 62.14432 When must my waste management plan be completed? As specified in §§ 62.14463 and 62.14464, you must submit your waste management plan with your...

40 CFR 60.2625 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management... or Before November 30, 1999 Model Rule-Waste Management Plan § 60.2625 When must I submit my waste management plan? You must submit a waste management plan no later than the date specified in table 1 of this...

40 CFR 62.14432 - When must my waste management plan be completed?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false When must my waste management plan be... Before June 20, 1996 Waste Management Plan § 62.14432 When must my waste management plan be completed? As specified in §§ 62.14463 and 62.14464, you must submit your waste management plan with your initial report...

The constraints of good governance practice in national solid waste management policy (NSWMP) implementation: A case study of Malaysia

NASA Astrophysics Data System (ADS)

Wee, Seow Ta; Abas, Muhamad Azahar; Chen, Goh Kai; Mohamed, Sulzakimin

2017-10-01

Nowadays, international donors have emphasised on the adoption of good governance practices in solid waste management which include policy implementation. In Malaysia, the National Solid Waste Management Policy (NSWMP) was introduced as the main guideline for its solid waste management and the Malaysian government has adopted good governance practice in the NSMWP implementation. However, the good governance practices implemented by the Malaysian government encountered several challenges. This study was conducted to explore the good governance constraints experienced by stakeholders in the NSWMP implementation. An exploratory research approach is applied in this study through in-depth interviews with several government agencies and concessionaires that involved in the NSWMP implementation in Malaysia. A total of six respondents took part in this study. The findings revealed three main good governance constraints in the NSWMP implementation, namely inadequate fund, poor staff's competency, and ambiguity of policy implementation system. Moreover, this study also disclosed that the main constraint influenced the other constraints. Hence, it is crucial to identify the main constraint in order to minimise its impact on the other constraints.

Application of material flow analysis to municipal solid waste in Maputo City, Mozambique.

PubMed

Dos Muchangos, Leticia Sarmento; Tokai, Akihiro; Hanashima, Atsuko

2017-03-01

Understanding waste flows within an urban area is important for identifying the main problems and improvement opportunities for efficient waste management. Assessment tools such as material flow analysis (MFA), an extensively applied method in waste management studies, provide a structured and objective evaluating process to characterize the waste management system best, to identify its shortcomings and to propose suitable strategies. This paper presents the application of MFA to municipal solid waste management (MSWM) in Maputo City, the capital of Mozambique. The results included the identification and quantification of the main input and output flows of the MSWM system in 2007 and 2014, from the generation, material recovery and collection, to final disposal and the unaccounted flow of municipal solid waste (MSW). We estimated that the waste generation increased from 397×10 3  tonnes in 2007 to 437×10 3  tonnes in 2014, whereas the total material recovery was insignificant in both years - 3×10 3 and 7×10 3  tonnes, respectively. As for collection and final disposal, the official collection of waste to the local dumpsite in the inner city increased about threefold, from 76×10 3 to 253×10 6  tonnes. For waste unaccounted for, the estimates indicated a reduction during the study period from 300×10 3 to 158×10 3  tonnes, due to the increase of collection services. The emphasized aspects include the need for practical waste reduction strategies, the opportunity to explore the potential for material recovery, careful consideration regarding the growing trend of illegal dumping and the urgency in phasing-out from the harmful practice of open dumping.

Household solid waste characteristics and management in Chittagong, Bangladesh.

PubMed

Sujauddin, Mohammad; Huda, S M S; Hoque, A T M Rafiqul

2008-01-01

Solid waste management (SWM) is a multidimensional challenge faced by urban authorities, especially in developing countries like Bangladesh. We investigated per capita waste generation by residents, its composition, and the households' attitudes towards waste management at Rahman Nagar Residential Area, Chittagong, Bangladesh. The study involved a structured questionnaire and encompassed 75 households from five different socioeconomic groups (SEGs): low (LSEG), lower middle (LMSEG), middle (MSEG), upper middle (UMSEG) and high (HSEG). Wastes, collected from all of the groups of households, were segregated and weighed. Waste generation was 1.3 kg/household/day and 0.25 kg/person/day. Household solid waste (HSW) was comprised of nine categories of wastes with vegetable/food waste being the largest component (62%). Vegetable/food waste generation increased from the HSEG (47%) to the LSEG (88%). By weight, 66% of the waste was compostable in nature. The generation of HSW was positively correlated with family size (r xy=0.236, p<0.05), education level (r xy=0.244, p<0.05) and monthly income (r xy=0.671, p<0.01) of the households. Municipal authorities are usually the responsible agencies for solid waste collection and disposal, but the magnitude of the problem is well beyond the ability of any municipal government to tackle. Hence dwellers were found to take the service from the local waste management initiative. Of the respondents, an impressive 44% were willing to pay US dollars 0.3 to US dollars 0.4 per month to waste collectors and it is recommended that service charge be based on the volume of waste generated by households. Almost a quarter (22.7%) of the respondents preferred 12-1 pm as the time period for their waste to be collected. This study adequately shows that household solid waste can be converted from burden to resource through segregation at the source, since people are aware of their role in this direction provided a mechanism to assist them in this pursuit exists and the burden is distributed according to the amount of waste generated.

Household solid waste characteristics and management in Chittagong, Bangladesh

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sujauddin, Mohammad; Huda, S.M.S.; Hoque, A.T.M. Rafiqul

2008-07-01

Solid waste management (SWM) is a multidimensional challenge faced by urban authorities, especially in developing countries like Bangladesh. We investigated per capita waste generation by residents, its composition, and the households' attitudes towards waste management at Rahman Nagar Residential Area, Chittagong, Bangladesh. The study involved a structured questionnaire and encompassed 75 households from five different socioeconomic groups (SEGs): low (LSEG), lower middle (LMSEG), middle (MSEG), upper middle (UMSEG) and high (HSEG). Wastes, collected from all of the groups of households, were segregated and weighed. Waste generation was 1.3 kg/household/day and 0.25 kg/person/day. Household solid waste (HSW) was comprised of ninemore » categories of wastes with vegetable/food waste being the largest component (62%). Vegetable/food waste generation increased from the HSEG (47%) to the LSEG (88%). By weight, 66% of the waste was compostable in nature. The generation of HSW was positively correlated with family size (r{sub xy} = 0.236, p < 0.05), education level (r{sub xy} = 0.244, p < 0.05) and monthly income (r{sub xy} = 0.671, p < 0.01) of the households. Municipal authorities are usually the responsible agencies for solid waste collection and disposal, but the magnitude of the problem is well beyond the ability of any municipal government to tackle. Hence dwellers were found to take the service from the local waste management initiative. Of the respondents, an impressive 44% were willing to pay US$0.3 to US$0.4 per month to waste collectors and it is recommended that service charge be based on the volume of waste generated by households. Almost a quarter (22.7%) of the respondents preferred 12-1 pm as the time period for their waste to be collected. This study adequately shows that household solid waste can be converted from burden to resource through segregation at the source, since people are aware of their role in this direction provided a mechanism to assist them in this pursuit exists and the burden is distributed according to the amount of waste generated.« less

Healthcare waste management in Asia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prem Ananth, A.; Prashanthini, V.; Visvanathan, C., E-mail: visu@ait.ac.t

The risks associated with healthcare waste and its management has gained attention across the world in various events, local and international forums and summits. However, the need for proper healthcare waste management has been gaining recognition slowly due to the substantial disease burdens associated with poor practices, including exposure to infectious agents and toxic substances. Despite the magnitude of the problem, practices, capacities and policies in many countries in dealing with healthcare waste disposal, especially developing nations, is inadequate and requires intensification. This paper looks upon aspects to drive improvements to the existing healthcare waste management situation. The paper placesmore » recommendation based on a 12 country study reflecting the current status. The paper does not advocate for any complex technology but calls for changes in mindset of all concerned stakeholders and identifies five important aspects for serious consideration. Understanding the role of governments and healthcare facilities, the paper also outlines three key areas for prioritized action for both parties - budget support, developing policies and legislation and technology and knowledge management.« less

Healthcare waste management in Asia.

PubMed

Ananth, A Prem; Prashanthini, V; Visvanathan, C

2010-01-01

The risks associated with healthcare waste and its management has gained attention across the world in various events, local and international forums and summits. However, the need for proper healthcare waste management has been gaining recognition slowly due to the substantial disease burdens associated with poor practices, including exposure to infectious agents and toxic substances. Despite the magnitude of the problem, practices, capacities and policies in many countries in dealing with healthcare waste disposal, especially developing nations, is inadequate and requires intensification. This paper looks upon aspects to drive improvements to the existing healthcare waste management situation. The paper places recommendation based on a 12 country study reflecting the current status. The paper does not advocate for any complex technology but calls for changes in mindset of all concerned stakeholders and identifies five important aspects for serious consideration. Understanding the role of governments and healthcare facilities, the paper also outlines three key areas for prioritized action for both parties - budget support, developing policies and legislation and technology and knowledge management.

Tribal Waste Management Program

EPA Pesticide Factsheets

The EPA’s Tribal Waste Management Program encourages environmentally sound waste management practices that promote resource conservation through recycling, recovery, reduction, clean up, and elimination of waste.

Management of construction and demolition wastes as secondary building resources

NASA Astrophysics Data System (ADS)

Manukhina, Lyubov; Ivanova, Irina

2017-10-01

The article analyzes the methods of management of construction and demolition wastes. The authors developed suggestions for improving the management system of the turnover of construction and demolition wastes. Today the issue of improving the management of construction and demolition wastes is of the same importance as problems of protecting the life-support field from pollution and of preserving biological and land resources. The authors educed the prospective directions and methods for improving the management of the turnover processes for construction and demolition wastes, including the evaluation of potential of wastes as secondary raw materials and the formation of a centralized waste management system.

Allocation of solid waste collection bins and route optimisation using geographical information system: A case study of Dhanbad City, India.

PubMed

Khan, D; Samadder, S R

2016-07-01

Collection of municipal solid waste is one of the most important elements of municipal waste management and requires maximum fund allocated for waste management. The cost of collection and transportation can be reduced in comparison with the present scenario if the solid waste collection bins are located at suitable places so that the collection routes become minimum. This study presents a suitable solid waste collection bin allocation method at appropriate places with uniform distance and easily accessible location so that the collection vehicle routes become minimum for the city Dhanbad, India. The network analyst tool set available in ArcGIS was used to find the optimised route for solid waste collection considering all the required parameters for solid waste collection efficiently. These parameters include the positions of solid waste collection bins, the road network, the population density, waste collection schedules, truck capacities and their characteristics. The present study also demonstrates the significant cost reductions that can be obtained compared with the current practices in the study area. The vehicle routing problem solver tool of ArcGIS was used to identify the cost-effective scenario for waste collection, to estimate its running costs and to simulate its application considering both travel time and travel distance simultaneously. © The Author(s) 2016.

40 CFR 273.13 - Waste management.

Code of Federal Regulations, 2013 CFR

2013-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A small quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.13 - Waste management.

Code of Federal Regulations, 2012 CFR

2012-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A small quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.33 - Waste management.

Code of Federal Regulations, 2013 CFR

2013-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A large quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.33 - Waste management.

Code of Federal Regulations, 2012 CFR

2012-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A large quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.13 - Waste management.

Code of Federal Regulations, 2011 CFR

2011-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A small quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.13 - Waste management.

Code of Federal Regulations, 2014 CFR

2014-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A small quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.33 - Waste management.

Code of Federal Regulations, 2014 CFR

2014-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A large quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

40 CFR 273.33 - Waste management.

Code of Federal Regulations, 2011 CFR

2011-07-01

... immediately closed after removal): (i) Sorting batteries by type; (ii) Mixing battery types in one container... Waste management. (a) Universal waste batteries. A large quantity handler of universal waste must manage universal waste batteries in a way that prevents releases of any universal waste or component of a universal...

Optimised management of orphan wastes in the UK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doudou, Slimane; McTeer, Jennifer; Wickham, Stephen

2013-07-01

Orphan wastes have properties preventing them from being managed according to existing or currently planned management routes, or lack characterisation so that their management is uncertain. The identification of new management opportunities for orphan wastes could realise significant benefits by reducing the number of processing facilities required, reducing waste volumes, reducing hazard or leading to the development of centres of excellence for the processing of certain types of orphan wastes. Information on the characteristics of orphan waste existing at nuclear licensed sites across the UK has been collated and a database developed to act as a repository for the informationmore » gathered. The database provides a capability to analyse the data and to explore possible treatment technologies for each orphan waste type. Thirty five distinct orphan waste types have been defined and possible treatment options considered. Treatment technologies (including chemical, high temperature, immobilisation and physical technologies) that could be applied to one or more of the generic orphan waste streams have been identified. Wiring diagrams have been used to highlight the waste treatment / lifecycle management options that are available for each of the generic orphan groups as well as identifying areas for further research and development. This work has identified the potential for optimising the management of orphan wastes in a number of areas, and many potential opportunities were identified. Such opportunities could be investigated by waste managers at waste producing nuclear sites, to facilitate the development of new management routes for orphan wastes. (authors)« less

Development of a waste management protocol based on assessment of knowledge and practice of healthcare personnel in surgical departments.

PubMed

Mostafa, Gehan M A; Shazly, Mona M; Sherief, Wafaa I

2009-01-01

Good healthcare waste management in a hospital depends on a dedicated waste management team, good administration, careful planning, sound organization, underpinning legislation, adequate financing, and full participation by trained staff. Hence, waste management protocols must be convenient and sensible. To assess the knowledge and practice related to waste management among doctors, nurses, and housekeepers in the surgical departments at Al-Mansoura University Hospital, and to design and validate a waste management protocol for the health team in these settings. This cross-sectional study was carried out in the eight surgical departments at Al-Mansoura University Hospital. All health care personnel and their assistants were included: 38 doctors, 106 nurses, and 56 housekeepers. Two groups of jury were included for experts' opinions validation of the developed protocol, one from academia (30 members) and the other from service providers (30 members). Data were collected using a self-administered knowledge questionnaire for nurses and doctors, and an interview questionnaire for housekeepers. Observation checklists were used for assessment of performance. The researchers developed the first draft of the waste management protocol according to the results of the analysis of the data collected in the assessment phase. Then, the protocol was presented to the jury group for validation, and then was implemented. Only 27.4% of the nurses, 32.1% of the housekeepers, and 36.8% of the doctors had satisfactory knowledge. Concerning practice, 18.9% of the nurses, 7.1% of the housekeepers, and none of the doctors had adequate practice. Nurses' knowledge score had a statistically significant weak positive correlation with the attendance of training courses (r=0.23, p<0.05). Validation of the developed protocol was done, and the percent of agreement ranged between 60.0% and 96.7% for the service group, and 60.0% and 90.0% for the academia group. The majority of the doctors, nurses, and housekeepers have unsatisfactory knowledge and inadequate practice related to health care waste management. The knowledge among nurses is positively affected by attendance of training programs. Based on the findings, a protocol for healthcare waste management was developed and validated. It is recommended to implement the developed waste management protocol for the surgical departments in the designed hospital, with establishment of waste management audits.

Treatment of an Anonymous Recipient: Solid-Waste Management Simulation Game

ERIC Educational Resources Information Center

Wu, Ko-Chiu; Huang, Po-Yuan

2015-01-01

This study developed a game simulation based on problem solving in the management of urban waste. We then investigated the factors affecting the decisions made by players. During gameplay, the players sought to guide the development of a city via management strategies involving a balance of economic growth and environmental protection. Nature…

Temporal evolution of the environmental performance of implementing selective collection in municipal waste management systems in developing countries: A Brazilian case study.

PubMed

Ibáñez-Forés, Valeria; Bovea, María D; Coutinho-Nóbrega, Claudia; de Medeiros-García, Hozana R; Barreto-Lins, Raissa

2018-02-01

The aim of this study is to analyse the evolution of the municipal solid waste management system of João Pessoa (Brazil), which was one of the Brazilian pioneers cities in implementing door-to-door selective collection programmes, in order to analyse the effect of policy decisions adopted in last decade with regard to selective collection. To do it, this study focuses on analysing the evolution, from 2005 to 2015, of the environmental performance of the municipal solid waste management (MSWM) system implemented in different sorting units with selective collection programmes by applying the Life Cycle Assessment (LCA) methodology and using as a starting point data collected directly from the different stakeholders involved in the MSWM system. This article presents the temporal evolution of environmental indicators measuring the environmental performance of the MSWM system implemented in João Pessoa by sorting unit, for each stage of the life cycle of the waste (collection, classification, intermediate transports, recycling and landfilling), for each waste fraction and for each collection method (selective collection or mixed collection), with the aim of identifying the key aspects with the greatest environmental impact and their causes. Results show on one hand, that environmental behaviour of waste management in a door-to-door selective collection programme significantly improves the behaviour of the overall waste management system. Consequently, the potential to reduce the existing environmental impact based on citizens' increased participation in selective collection is evidenced, so the implementation of awareness-raising campaigns should be one of the main issues of the next policies on solid waste. On the other hand, increasing the amount of recyclable wastes collected selectively, implementing alternative methods for valorising the organic fraction (compost/biomethanization) and improving the efficiency of the transportation stage by means of optimizing vehicles or routes, are essential actions to reduce the overall net environmental impact generated by the MSWM system. Copyright © 2017 Elsevier Ltd. All rights reserved.

Greenhouse gases emissions from waste management practices using Life Cycle Inventory model.

PubMed

Chen, Tsao-Chou; Lin, Cheng-Fang

2008-06-30

When exploring the correlation between municipal solid waste management and green house gas emission, the volume and physical composition of the waste matter must be taken into account. Due to differences in local environments and lifestyles the quantity and composition of waste often vary. This leads to differences in waste treatment methods and causes different volumes of greenhouse gases (GHGs), highlighting the need for local research. In this study the Life Cycle Inventory method was used with global warming indicator GHGs as the variables. By quantifying the data and adopting a region-based approach, this created a model of household MSWM in Taipei City, a metropolitan region in Taiwan. To allow analysis and comparison a compensatory system was then added to expand the system boundary. The results of the analysis indicated that out of all the solid waste management sub-models for a function unit, recycling was the most effective method for reducing GHG emissions while using kitchen food waste as swine feeding resulted in the most GHG emissions. As for the impact of waste collection vehicles on emissions, if the efficiency of transportation could be improved and energy consumption reduced, this will help solid waste management to achieve its goal of reducing GHG emissions.

Hazardous healthcare waste management in the Kingdom of Bahrain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, L.F.; Ebrahim, S.A.; Al-Thukair, A.A.

2009-08-15

Hazardous healthcare waste has become an environmental concern for many developing countries including the Kingdom of Bahrain. There have been several significant obstacles facing the Kingdom in dealing with this issue including; limited documentation regarding generation, handling, management, and disposal of waste. This in turn hinders efforts to plan better healthcare waste management. In this paper, hazardous waste management status in the Kingdom has been investigated through an extensive survey carried out on selected public and private healthcare premises. Hazardous waste management practices including: waste generation, segregation, storage, collection, transportation, treatment, and disposal were determined. The results of this studymore » along with key findings are discussed and summarized. In addition; several effective recommendations and improvements of hazardous waste management are suggested.« less

Cultivating Composting Culture Activities among Citizens and Its Beneficial to Prolong the Landfill Lifespan

NASA Astrophysics Data System (ADS)

Azura Zakarya, Irnis; Azri Jamial, Khairul; Mat Tanda, Norazlinda

2018-03-01

Currently, the Ministry of Housing and Local Government manage solid waste in Malaysia, with the participation of the private sector. Food waste represents almost 60% of the total municipal solid waste disposed in the landfill. Material valorisation of food waste usually conducted by biological processes such as composting. Compost, an organic amendment, is the final product of the composting process. These processes are efficient, low cost and environmentally friendly alternative for managing food waste and are used extensively worldwide. Therefore, organic solid waste management practices program for the communities in Perlis was conducted. The main objective of this program was to instilling environment awareness especially among Perlis citizens. This study was investigated the impact of food waste or kitchen waste composting to the citizens in Perlis State and the beneficial of compost fertilizer to our environment especially in plant growth. Composting method was taught to the food premises owner, individuals, teachers, and students and their responses to the composting practices were then summarized. In future, we can prolong our landfill lifespan by practicing organic waste composting and can preserving our environment.

Marine pollution and management of shores; Pollutions marines et amenagement des rivages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aubert, M.; Aubert, J.

1973-01-01

The fourteen chapters of the book are presented in three sections entitled description of marine pollution, oceanographic techniques in marine pollution studies, and prevention of marine pollution and management of shores. The first section discusses thermal, bacterial, radioactive, chemical and organic pollution. In the chapter on thermal pollution, emphasis is placed on the effects of heated effluents on the ecological balance of estuaries. Effects of waste products from nuclear industries are discussed in the chapter on radioactive pollution as well as the development of fission products, radioactive wastes from nuclear-propulsion ships, wastes from nuclear accidents, and wastes from atomic bombmore » explosions. Measures for prevention of pollution include management of stream mouths and studies on pollution of parts and artificial beaches. (approximately 200 references) (HLW)« less

Waste Generation Overview Refresher, Course 21464

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simpson, Lewis Edward

This course, Waste Generation Overview Refresher (COURSE 21464), provides an overview of federal and state waste management regulations, as well as Los Alamos National Laboratory (LANL) policies and procedures for waste management operations. The course covers the activities involved in the cradle-to- grave waste management process and focuses on waste characterization, waste compatibility determinations and classification, and the storage requirements for temporary waste accumulation areas at LANL.

[Management of hazardous waste in a hospital].

PubMed

Neveu C, Alejandra; Matus C, Patricia

2007-07-01

An inadequate management of hospital waste, that have toxic, infectious and chemical wastes, is a risk factor for humans and environment. To identify, quantify and assess the risk associated to the management of hospital residues. A cross sectional assessment of the generation of hazardous waste from a hospital, between June and August 2005, was performed. The environmental risk associated to the management of non-radioactive hospital waste was assessed and the main problems related to solid waste were identified. The rate of generation of hazardous non-radioactive waste was 1.35 tons per months or 0.7 kg/bed/day. Twenty five percent of hazardous liquid waste were drained directly to the sewage system. The drug preparation unit of the pharmacy had the higher environmental risk associated to the generation of hazardous waste. The internal transport of hazardous waste had a high risk due to the lack of trip planning. The lack of training of personnel dealing with these waste was another risk factor. Considering that an adequate management of hospital waste should minimize risks for patients, the hospital that was evaluated lacks an integral management system for its waste.

40 CFR 60.2755 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false When must I submit my waste management... waste management plan? You must submit the waste management plan no later than the date specified in... Compliance Times for Commercial and Industrial Solid Waste Incineration Units that Commenced Construction On...

40 CFR 62.14715 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false When must I submit my waste management... submit my waste management plan? You must submit the waste management plan no later than April 5, 2004. ... POLLUTANTS Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That...

40 CFR 62.14715 - When must I submit my waste management plan?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false When must I submit my waste management... submit my waste management plan? You must submit the waste management plan no later than April 5, 2004. ... POLLUTANTS Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That...

40 CFR 60.2755 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management... waste management plan? You must submit the waste management plan no later than the date specified in... Compliance Times for Commercial and Industrial Solid Waste Incineration Units that Commenced Construction On...

40 CFR 62.14715 - When must I submit my waste management plan?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 9 2014-07-01 2014-07-01 false When must I submit my waste management... submit my waste management plan? You must submit the waste management plan no later than April 5, 2004. ... POLLUTANTS Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That...

40 CFR 62.14715 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 9 2012-07-01 2012-07-01 false When must I submit my waste management... submit my waste management plan? You must submit the waste management plan no later than April 5, 2004. ... POLLUTANTS Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That...

40 CFR 62.14715 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... POLLUTANTS Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That... 40 Protection of Environment 8 2011-07-01 2011-07-01 false When must I submit my waste management... submit my waste management plan? You must submit the waste management plan no later than April 5, 2004. ...

40 CFR 62.14580 - What is a waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Federal Plan Requirements for Commercial and Industrial Solid Waste Incineration Units That Commenced Construction On or Before November 30, 1999 Waste Management Plan § 62.14580 What is a waste management plan? A... 40 Protection of Environment 8 2011-07-01 2011-07-01 false What is a waste management plan? 62...

40 CFR 62.14432 - When must my waste management plan be completed?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 9 2013-07-01 2013-07-01 false When must my waste management plan be... POLLUTANTS Federal Plan Requirements for Hospital/Medical/Infectious Waste Incinerators Constructed On Or Before December 1, 2008 Waste Management Plan § 62.14432 When must my waste management plan be completed...

Waste Management Information System (WMIS) User Guide

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. E. Broz

2008-12-22

This document provides the user of the Waste Management Information System (WMIS) instructions on how to use the WMIS software. WMIS allows users to initiate, track, and close waste packages. The modular design supports integration and utilization of data throuh the various stages of waste management. The phases of the waste management work process include generation, designation, packaging, container management, procurement, storage, treatment, transportation, and disposal.

Household-level dynamics of food waste production and related beliefs, attitudes, and behaviours in Guelph, Ontario.

PubMed

Parizeau, Kate; von Massow, Mike; Martin, Ralph

2015-01-01

It has been estimated that Canadians waste $27 billion of food annually, and that half of that waste occurs at the household level (Gooch et al., 2010). There are social, environmental, and economic implications for this scale of food waste, and source separation of organic waste is an increasingly common municipal intervention. There is relatively little research that assesses the dynamics of household food waste (particularly in Canada). The purpose of this study is to combine observations of organic, recyclable, and garbage waste production rates to survey results of food waste-related beliefs, attitudes, and behaviours at the household level in the mid-sized municipality of Guelph, Ontario. Waste weights and surveys were obtained from 68 households in the summer of 2013. The results of this study indicate multiple relationships between food waste production and household shopping practices, food preparation behaviours, household waste management practices, and food-related attitudes, beliefs, and lifestyles. Notably, we observed that food awareness, waste awareness, family lifestyles, and convenience lifestyles were related to food waste production. We conclude that it is important to understand the diversity of factors that can influence food wasting behaviours at the household level in order to design waste management systems and policies to reduce food waste. Copyright © 2014 Elsevier Ltd. All rights reserved.

WHO collaboration in hazardous waste management in the Western Pacific Region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogawa, Hisashi

Since April 1989 when the World Health Organization`s (WHO`s) activities in hazardous waste management in the Western Pacific Region were presented at the Pacific Basin Conference in Singapore, WHO and its Member States have carried out a number of collaborative activities in hazardous waste management. These activities focused on three main areas: national capacity building in the management of toxic chemicals and hazardous wastes in rapidly industrializing countries, management of clinical or medical waste, and hazardous waste management in Pacific Island countries. This paper summarizes these collaborative activities, identifies the main problems and issues encountered, and discusses future prospects ofmore » WHO collaboration with its Member States in the area of hazardous waste management. 1 fig., 1 tab.« less

Applying Nightingale charts to evaluate the heterogeneity of biomedical waste in a Hospital

PubMed Central

Paiz, Janini Cristina; Bigolin, Marcio; Schneider, Vania Elisabete; Stedile, Nilva Lúcia Rech

2014-01-01

OBJECTIVES: to evaluate the heterogeneity of biomedical waste (BW) using Nightingale charts. METHOD: cross-sectional study consisting of data collection on wastes (direct observation of receptacles, physical characterisation, and gravimetric composition), development of a Management Information System, and creation of statistical charts. RESULTS: the wastes with the greatest degree of heterogeneity are, in order, recyclable, infectious, and organic wastes; chemical waste had the most efficient segregation; Nightingale charts are useful for quick visualisation and systematisation of information on heterogeneity. CONCLUSION: the development of a management information system and the use of Nightingale charts allows for the identification and correction of errors in waste segregation, which increase health risks and contamination by infectious and chemical wastes and reduce the sale and profit from recyclables. PMID:25591088

C balance, carbon dioxide emissions and global warming potentials in LCA-modelling of waste management systems.

PubMed

Christensen, Thomas H; Gentil, Emmanuel; Boldrin, Alessio; Larsen, Anna W; Weidema, Bo P; Hauschild, Michael

2009-11-01

Global warming potential (GWP) is an important impact category in life-cycle-assessment modelling of waste management systems. However, accounting of biogenic CO(2) emissions and sequestered biogenic carbon in landfills and in soils, amended with compost, is carried out in different ways in reported studies. A simplified model of carbon flows is presented for the waste management system and the surrounding industries, represented by the pulp and paper manufacturing industry, the forestry industry and the energy industry. The model calculated the load of C to the atmosphere, under ideal conditions, for 14 different waste management scenarios under a range of system boundary conditions and a constant consumption of C-product (here assumed to be paper) and energy production within the combined system. Five sets of criteria for assigning GWP indices to waste management systems were applied to the same 14 scenarios and tested for their ability to rank the waste management alternatives reflecting the resulting CO(2) load to the atmosphere. Two complete criteria sets were identified yielding fully consistent results; one set considers biogenic CO(2) as neutral, the other one did not. The results showed that criteria for assigning global warming contributions are partly linked to the system boundary conditions. While the boundary to the paper industry and the energy industry usually is specified in LCA studies, the boundary to the forestry industry and the interaction between forestry and the energy industry should also be specified and accounted for.

Waste management/waste certification plan for the Oak Ridge National Laboratory Environmental Restoration Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, C. Jr.; Hunt-Davenport, L.D.; Cofer, G.H.

1995-03-01

This Waste Management/Waste Certification (C) Plan, written for the Environmental Restoration (ER) Program at Oak Ridge National Laboratory (ORNL), outlines the criteria and methodologies to be used in the management of waste generated during ORNL ER field activities. Other agreed upon methods may be used in the management of waste with consultation with ER and Waste Management Organization. The intent of this plan is to provide information for the minimization, handling, and disposal of waste generated by ER activities. This plan contains provisions for the safe and effective management of waste consistent with the U.S. Environmental Protection Agency`s (EPA`s) guidance.more » Components of this plan have been designed to protect the environment and the health and safety of workers and the public. It, therefore, stresses that investigation derived waste (IDW) and other waste be managed to ensure that (1) all efforts be made to minimize the amount of waste generated; (2) costs associated with sampling storage, analysis, transportation, and disposal are minimized; (3) the potential for public and worker exposure is not increased; and (4) additional contaminated areas are not created.« less

Research on solid waste management system: to improve existing situation in Corlu Town of Turkey.

PubMed

Tinmaz, Esra; Demir, Ibrahim

2006-01-01

Over the past decades, uncontrolled population growth and rapid urbanization and industrialization have resulted in environmental problems in Corlu Town, Turkey. One of the most important problems is solid waste due to inadequate management practices. Nowadays, increasing public awareness of the environment compels local authorities to define and to adopt new solutions for waste management. This paper presents a general overview of current solid waste management practices in Corlu Town and principles of the recommended municipal solid waste (MSW) management system. In Corlu, 170 tonnes of municipal solid waste are generated each day, or 1.150 kg per capita per day. Approximately one-half of the municipal solid waste generated is organic material and 30% of the MSW consists of recyclable materials. The recommended system deals with maximizing recycling and minimizing landfilling of municipal solid waste, and consists of separation at source, collection, sorting, recycling, composting and sanitary landfilling. This study also analyzed the recommended system with respect to feasibility and economics. To evaluate whether the suggested system is cost effective or not, the operating cost of the recommended system and market prices of recyclable materials were compared, and the results show that the recommended system will reduce required landfill volume up to 27% of compared to the present situation. The profit of the recommended system is estimated to be about 80 million US dollars.

Multi-criteria evaluation in strategic environmental assessment for waste management plan, a case study: the city of Belgrade.

PubMed

Josimović, Boško; Marić, Igor; Milijić, Saša

2015-02-01

Strategic Environmental Assessment (SEA) is one of the key instruments for implementing sustainable development strategies in planning in general; in addition to being used in sectoral planning, it can also be used in other areas such as waste management planning. SEA in waste management planning has become a tool for considering the benefits and consequences of the proposed changes in space, also taking into account the capacity of space to sustain the implementation of the planned activities. In order to envisage both the positive and negative implications of a waste management plan for the elements of sustainable development, an adequate methodological approach to evaluating the potential impacts must be adopted and the evaluation results presented in a simple and clear way, so as to allow planners to make relevant decisions as a precondition for the sustainability of the activities planned in the waste management sector. This paper examines the multi-criteria evaluation method for carrying out an SEA for the Waste Management Plan for the city of Belgrade (BWMP). The method was applied to the evaluation of the impacts of the activities planned in the waste management sector on the basis of the environmental and socioeconomic indicators of sustainability, taking into consideration the intensity, spatial extent, probability and frequency of impact, by means of a specific planning approach and simple and clear presentation of the obtained results. Copyright © 2014 Elsevier Ltd. All rights reserved.

Destined for indecision? A critical analysis of waste management practices in England from 1996 to 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, T.D.; Shaw, P.J.; Williams, I.D., E-mail: idw@soton.ac.uk

Highlights: • Critical analysis of municipal waste management practices and performance in England. • Trends visualised via innovative ternary plots and changes and reasons explored. • Performance 1996–2013 moved slowly away from landfill dominance. • Large variations in %s of waste landfilled, incinerated and recycled/composted. • Progress to resource efficiency slow; affected by poor planning and hostile disputes. - Abstract: European nations are compelled to reduce reliance on landfill as a destination for household waste, and should, in principle, achieve this goal with due recognition of the aims and principles of the waste hierarchy. Past research has predominantly focused onmore » recycling, whilst interactions between changing waste destinies, causes and drivers of household waste management change, and potential consequences for the goal of the waste hierarchy are less well understood. This study analysed Local Authority Collected Waste (LACW) for England, at national, regional and sub-regional level, in terms of the destination of household waste to landfill, incineration and recycling. Information about waste partnerships, waste management infrastructure and collection systems was collected to help identify and explain changes in waste destinies. Since 1996, the proportion of waste landfilled in England has decreased, in tandem with increases in recycling and incineration. At the regional and sub-regional (Local Authority; LA) level, there have been large variations in the relative proportions of waste landfilled, incinerated and recycled or composted. Annual increases in the proportion of household waste incinerated were typically larger than increases in the proportion recycled. The observed changes took place in the context of legal and financial drivers, and the circumstances of individual LAs (e.g. landfill capacity) also explained the changes seen. Where observed, shifts from landfill towards incineration constitute an approach whereby waste management moves up the waste hierarchy as opposed to an attempt to reach the most preferred option(s); in terms of resource efficiency, this practice is sub-optimal. The requirement to supply incinerators with a feedstock over their lifespan reduces the benefits of developing of recycling and waste reduction, although access to incineration infrastructure permits short-term and marked decreases in the proportion of LACW landfilled. We conclude that there is a need for clearer national strategy and co-ordination to inform and guide policy, practice, planning and investment in infrastructure such that waste management can be better aligned with the principles of the circular economy and resource efficiency. If the ongoing stand-off between national political figures and the waste sector continues, England’s waste policy remains destined for indecision.« less

Participatory approach, acceptability and transparency of waste management LCAs: case studies of Torino and Cuneo.

PubMed

Blengini, Gian Andrea; Fantoni, Moris; Busto, Mirko; Genon, Giuseppe; Zanetti, Maria Chiara

2012-09-01

The paper summarises the main results obtained from two extensive applications of Life Cycle Assessment (LCA) to the integrated municipal solid waste management systems of Torino and Cuneo Districts in northern Italy. Scenarios with substantial differences in terms of amount of waste, percentage of separate collection and options for the disposal of residual waste are used to discuss the credibility and acceptability of the LCA results, which are adversely affected by the large influence of methodological assumptions and the local socio-economic constraints. The use of site-specific data on full scale waste treatment facilities and the adoption of a participatory approach for the definition of the most sensible LCA assumptions are used to assist local public administrators and stakeholders showing them that LCA can be operational to waste management at local scale. Copyright © 2012 Elsevier Ltd. All rights reserved.

Strategies for waste management in small and medium towns of developing countries: a case study of India.

PubMed

Sundaravadivel, M; Vigneswaran, S

2003-01-01

This paper evaluates the issues of waste management in small and medium towns (SMTs) (with population in the range of 10,000-100,000) of India, and identifies the need for a multi-disciplinary approach encompassing technological, economic and financial aspects of the issues to effect improvements. A comprehensive set of cross-disciplinary strategies is suggested to improve the prevailing conditions with environmentally appropriate, economically efficient and financially self-sustaining waste management services. Based on a case study of four SMTs in the State of Tamil Nadu in India, this paper evaluates the application of the suggested strategies and offers policy recommendations.

Community Air Sensor Network CAIRSENSE Project: Lower ...

EPA Pesticide Factsheets

Presentation slides on the CAIRSENSE project, Atlanta field study testing low cost air sensors against FEM instruments. To be presented at the Air and Waste Management Association conference. Presentation slides on the CAIRSENSE project, Atlanta field study testing low cost air sensors against FEM instruments. To be presented at the Air and Waste Management Association conference.

SPECIAL ISSUE OF THE JOURNAL OF THE AIR & WASTE MANAGEMENT ASSOCIATION ON THE PARTICULATE MATTER SUPERSITES PROGRAM AND RELATED STUDIES

EPA Science Inventory

This article is the preface or editors note to the dedicated issue of the Journal of the Air & Waste Management Association for a selection of scientific papers from the specialty conference entitled, "Particulate Matter Supersites Program and Related Studies," that was...

An integrated approach for the management of demolition waste in Cyprus.

PubMed

Kourmpanis, Basilis; Papadopoulos, Achilleas; Moustakas, Konstantinos; Kourmoussis, Fotis; Stylianou, Marinos; Loizidou, Maria

2008-12-01

This study investigated the generation and management of demolition waste (DW) in Cyprus. A methodology has been developed and applied for the estimation of the quantities of the waste stream under examination, since quantitative primary data were not available. The existing situation relating to the practices applied for the management of DW was investigated and assessed. Furthermore, a multi-criteria analysis method (PROMETHEE II) was developed and applied in order to examine alternative systems that could be implemented for the management of the DW in the country. In particular, nine management systems (scenarios) were examined, evaluated and ranked according to their efficiency using seventeen individual criteria, divided into four groups (social-legislative, environmental, economic and technical). The ranking of the alternative waste management scenarios indicated that the optimum management system for possible implementation in the island included complete selective demolition procedures and transfer of mixed recyclable materials to the recycling centre and non-recyclable material to landfill.

Management of immunization solid wastes in Kano State, Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oke, I.A.

Inadequate management of waste generated from injection activities can have a negative impact on the community and environment. In this paper, a report on immunization wastes management in Kano State (Nigeria) is presented. Eight local governments were selected randomly and surveyed by the author. Solid wastes generated during the Expanded Programme on Immunization were characterised using two different methods: one by weighing the waste and the other by estimating the volume. Empirical data was obtained on immunization waste generation, segregation, storage, collection, transportation, and disposal; and waste management practices were assessed. The study revealed that immunization offices were accommodated inmore » either in local government buildings, primary health centres or community health care centres. All of the stations demonstrated a high priority for segregation of the infectious wastes. It can be deduced from the data obtained that infectious waste ranged from 67.6% to 76.7% with an average of 70.1% by weight, and 36.0% to 46.1% with an average of 40.1% by volume. Non-infectious waste generated ranged from 23.3% to 32.5% with an average of 29.9% by weight and 53.9% to 64.0% with an average of 59.9% by volume. Out of non-infectious waste (NIFW) and infectious waste (IFW), 66.3% and 62.4% by weight were combustible and 33.7% and 37.6% were non-combustible respectively. An assessment of the treatment revealed that open pit burning and burial and small scale incineration were the common methods of disposal for immunization waste, and some immunization centres employed the services of the state or local government owned solid waste disposal board for final collection and disposal of their immunization waste at government approved sites.« less

40 CFR 60.2755 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management... Compliance Times for Commercial and Industrial Solid Waste Incineration Units Model Rule-Recordkeeping and Reporting § 60.2755 When must I submit my waste management plan? You must submit the waste management plan...

76 FR 63252 - Hazardous and Solid Waste Management System: Identification and Listing of Special Wastes...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-12

...-2011-0392; FRL-9476-6] RIN 2050-AE81 Hazardous and Solid Waste Management System: Identification and... Protection Agency (Agency or EPA) in conjunction with the proposed rule: Hazardous and Solid Waste Management...-0392. (4) Mail: Send two copies of your comments to Hazardous and Solid Waste Management System...

40 CFR 60.3011 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false When must I submit my waste management... Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Waste Management Plan § 60.3011 When must I submit my waste management plan? You must submit...

A system dynamics model to evaluate effects of source separation of municipal solid waste management: A case of Bangkok, Thailand.

PubMed

Sukholthaman, Pitchayanin; Sharp, Alice

2016-06-01

Municipal solid waste has been considered as one of the most immediate and serious problems confronting urban government in most developing and transitional economies. Providing solid waste performance highly depends on the effectiveness of waste collection and transportation process. Generally, this process involves a large amount of expenditures and has very complex and dynamic operational problems. Source separation has a major impact on effectiveness of waste management system as it causes significant changes in quantity and quality of waste reaching final disposal. To evaluate the impact of effective source separation on waste collection and transportation, this study adopts a decision support tool to comprehend cause-and-effect interactions of different variables in waste management system. A system dynamics model that envisages the relationships of source separation and effectiveness of waste management in Bangkok, Thailand is presented. Influential factors that affect waste separation attitudes are addressed; and the result of change in perception on waste separation is explained. The impacts of different separation rates on effectiveness of provided collection service are compared in six scenarios. 'Scenario 5' gives the most promising opportunities as 40% of residents are willing to conduct organic and recyclable waste separation. The results show that better service of waste collection and transportation, less monthly expense, extended landfill life, and satisfactory efficiency of the provided service at 60.48% will be achieved at the end of the simulation period. Implications of how to get public involved and conducted source separation are proposed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Construction and demolition waste generation rates for high-rise buildings in Malaysia.

PubMed

Mah, Chooi Mei; Fujiwara, Takeshi; Ho, Chin Siong

2016-12-01

Construction and demolition waste continues to sharply increase in step with the economic growth of less developed countries. Though the construction industry is large, it is composed of small firms with individual waste management practices, often leading to the deleterious environmental outcomes. Quantifying construction and demolition waste generation allows policy makers and stakeholders to understand the true internal and external costs of construction, providing a necessary foundation for waste management planning that may overcome deleterious environmental outcomes and may be both economically and environmentally optimal. This study offers a theoretical method for estimating the construction and demolition project waste generation rate by utilising available data, including waste disposal truck size and number, and waste volume and composition. This method is proposed as a less burdensome and more broadly applicable alternative, in contrast to waste estimation by on-site hand sorting and weighing. The developed method is applied to 11 projects across Malaysia as the case study. This study quantifies waste generation rate and illustrates the construction method in influencing the waste generation rate, estimating that the conventional construction method has a waste generation rate of 9.88 t 100 m -2 , the mixed-construction method has a waste generation rate of 3.29 t 100 m -2 , and demolition projects have a waste generation rate of 104.28 t 100 m -2 . © The Author(s) 2016.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banar, Mufide; Cokaygil, Zerrin; Ozkan, Aysun

Life cycle assessment (LCA) methodology was used to determine the optimum municipal solid waste (MSW) management strategy for Eskisehir city. Eskisehir is one of the developing cities of Turkey where a total of approximately 750 tons/day of waste is generated. An effective MSW management system is needed in this city since the generated MSW is dumped in an unregulated dumping site that has no liner, no biogas capture, etc. Therefore, five different scenarios were developed as alternatives to the current waste management system. Collection and transportation of waste, a material recovery facility (MRF), recycling, composting, incineration and landfilling processes weremore » considered in these scenarios. SimaPro7 libraries were used to obtain background data for the life cycle inventory. One ton of municipal solid waste of Eskisehir was selected as the functional unit. The alternative scenarios were compared through the CML 2000 method and these comparisons were carried out from the abiotic depletion, global warming, human toxicity, acidification, eutrophication and photochemical ozone depletion points of view. According to the comparisons and sensitivity analysis, composting scenario, S3, is the more environmentally preferable alternative. In this study waste management alternatives were investigated only on an environmental point of view. For that reason, it might be supported with other decision-making tools that consider the economic and social effects of solid waste management.« less

Arsenic: a roadblock to potential animal waste management solutions.

PubMed

Nachman, Keeve E; Graham, Jay P; Price, Lance B; Silbergeld, Ellen K

2005-09-01

The localization and intensification of the poultry industry over the past 50 years have incidentally created a largely ignored environmental management crisis. As a result of these changes in poultry production, concentrated animal feeding operations (CAFOs) produce far more waste than can be managed by land disposal within the regions where it is produced. As a result, alternative waste management practices are currently being implemented, including incineration and pelletization of waste. However, organic arsenicals used in poultry feed are converted to inorganic arsenicals in poultry waste, limiting the feasibility of waste management alternatives. The presence of inorganic arsenic in incinerator ash and pelletized waste sold as fertilizer creates opportunities for population exposures that did not previously exist. The removal of arsenic from animal feed is a critical step toward safe poultry waste management.

40 CFR 62.14431 - What must my waste management plan include?

Code of Federal Regulations, 2010 CFR

2010-07-01

... waste management plan must identify both the feasibility of, and the approach for, separating certain components of solid waste from the health care waste stream in order to reduce the amount of toxic emissions from incinerated waste. The waste management plan you develop may address, but is not limited to, paper...

40 CFR 62.14431 - What must my waste management plan include?

Code of Federal Regulations, 2011 CFR

2011-07-01

... waste management plan must identify both the feasibility of, and the approach for, separating certain components of solid waste from the health care waste stream in order to reduce the amount of toxic emissions from incinerated waste. The waste management plan you develop may address, but is not limited to, paper...

Industrial-waste management in developing countries: the case of Lebanon.

PubMed

el-Fadel, M; Zeinati, M; el-Jisr, K; Jamali, D

2001-04-01

This paper presents a critical assessment of the existing Lebanese industrial sector, namely the current status and classification of industrial establishments based on a comparative synthesis and analysis of recent nationwide surveys and studies pertaining to industrial-waste management. Characterisation of solid and liquid industrial wastes generated, including hazardous wastes, is presented together with current and projected waste loads, recycling opportunities, and export/import practices. Institutional capacity and needs pertaining to the enforcement of relevant environmental legislation, staffing and resources, monitoring schemes, and public participation are critically evaluated. Finally, realistic options for industrial-waste management in the context of country-specific institutional economic and technical limitations are outlined. The industrial sector in Lebanon consists of small-scale industries (84% employ less than 10 persons), primarily involved in light manufacturing (96%). These industries which are distributed among 41 ill-defined zones and deficient in appropriate physical infrastructure, generate solid, liquid, and hazardous waste estimated at 346,730 tons/year, 20,169,600 m3/year and between 3000 to 15,000 tons/year, respectively. Although the growth of this sector contributes significantly to the socio-economic development of the country (industry accounts for 17% of the gross domestic product), in the absence of a comprehensive environmental management plan, this expansion may not be sustained into the coming millennium. The anticipated expansion will inevitably amplify adverse environmental impacts associated with industrial activities due to rising waste volumes and improper waste handling and disposal practices. These impacts are further aggravated by a deficient institutional framework, a lack of adequate environmental laws, and lax enforcement of regulations governing industrial-waste management.

Implementation of SAP Waste Management System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frost, M.L.; LaBorde, C.M.; Nichols, C.D.

2008-07-01

The Y-12 National Security Complex (Y-12) assumed responsibility for newly generated waste on October 1, 2005. To ensure effective management and accountability of newly generated waste, Y-12 has opted to utilize SAP, Y-12's Enterprise Resource Planning (ERP) tool, to track low-level radioactive waste (LLW), mixed waste (MW), hazardous waste, and non-regulated waste from generation through acceptance and disposal. SAP Waste will include the functionality of the current waste tracking system and integrate with the applicable modules of SAP already in use. The functionality of two legacy systems, the Generator Entry System (GES) and the Waste Information Tracking System (WITS), andmore » peripheral spreadsheets, databases, and e-mail/fax communications will be replaced by SAP Waste. Fundamentally, SAP Waste will promote waste acceptance for certification and disposal, not storage. SAP Waste will provide a one-time data entry location where waste generators can enter waste container information, track the status of their waste, and maintain documentation. A benefit of the new system is that it will provide a single data repository where Y-12's Waste Management organization can establish waste profiles, verify and validate data, maintain inventory control utilizing hand-held data transfer devices, schedule and ship waste, manage project accounting, and report on waste handling activities. This single data repository will facilitate the production of detailed waste generation reports for use in forecasting and budgeting, provide the data for required regulatory reports, and generate metrics to evaluate the performance of the Waste Management organization and its subcontractors. SAP Waste will replace the outdated and expensive legacy system, establish tools the site needs to manage newly generated waste, and optimize the use of the site's ERP tool for integration with related business processes while promoting disposition of waste. (authors)« less

Determining heavy metals in spent compact fluorescent lamps (CFLs) and their waste management challenges: some strategies for improving current conditions.

PubMed

Taghipour, Hassan; Amjad, Zahra; Jafarabadi, Mohamad Asghari; Gholampour, Akbar; Norouz, Prviz

2014-07-01

From environmental viewpoint, the most important advantage of compact fluorescent lamps (CFLs) is reduction of green house gas emissions. But their significant disadvantage is disposal of spent lamps because of containing a few milligrams of toxic metals, especially mercury and lead. For a successful implementation of any waste management plan, availability of sufficient and accurate information on quantities and compositions of the generated waste and current management conditions is a fundamental prerequisite. In this study, CFLs were selected among 20 different brands in Iran. Content of heavy metals including mercury, lead, nickel, arsenic and chromium was determined by inductive coupled plasma (ICP). Two cities, Tehran and Tabriz, were selected for assessing the current waste management condition of CFLs. The study found that waste generation amount of CFLs in the country was about 159.80, 183.82 and 153.75 million per year in 2010, 2011 and 2012, respectively. Waste generation rate of CFLs in Iran was determined to be 2.05 per person in 2012. The average amount of mercury, lead, nickel, arsenic and chromium was 0.417, 2.33, 0.064, 0.056 and 0.012 mg per lamp, respectively. Currently, waste of CFLs is disposed by municipal waste stream in waste landfills. For improving the current conditions, we propose by considering the successful experience of extended producer responsibility (EPR) in other electronic waste management. The EPR program with advanced recycling fee (ARF) is implemented for collecting and then recycling CFLs. For encouraging consumers to take the spent CFLs back at the end of the products' useful life, a proportion of ARF (for example, 50%) can be refunded. On the other hand, the government and Environmental Protection Agency should support and encourage recycling companies of CFLs both technically and financially in the first place. Copyright © 2014 Elsevier Ltd. All rights reserved.

The contribution of multidimensional spatial analysis to a waste management policy: implementation of the ELECTRE method for characterizing transfer centers in the region of Oran

NASA Astrophysics Data System (ADS)

Saidi, A.; Trache, M. A.; Khelfi, M. F.

2016-08-01

The social and economic activity steadily growing in our cities creates a significant waste production in constantly evolving. The management of this waste is problematic because it is the center of many issues and interests. Indeed, any action or decision to the collection, transportation, treatment and disposal of waste should be considered in the economic, social, political and especially environmental aspect. A global Geomatic solution requires implementing a GIS with powerful multidimensional spatial analysis tools that support really waste management problem. Algeria has adopted a solution of waste landfill for all urban cities. In the Oran region, it exists three Centers Controlled landfill (CET) which the most important is that of Hassi-Bounif. This center currently meeting the needs of the region is unsustainable solution at the long-term because of its rapid saturation and its geographic location, which is still far from city centers (20-30 km) implying a negative impact on the vehicle park collecting such frequent breakdowns, the rapid degradation, slow delivery time and especially the high cost of the maintenance operation. This phenomenon is aggravated by the absence of real and actual initiatives targeting the recycling and recovery of waste, which makes the CET an endpoint for all types of waste. We present in this study, the use of the ELECTRE method (Multicriteria Analysis) integrated into a GIS to characterize the impact of the implementation of transfers centers at Oran region. The results of this study will accentuate the advantages of the activation of waste warehouse closer to the city, and relieving considerably the volume of transfer towards CET. The objective of our presentation is to show the leading role of the new Geomatics tools and the multidimensional spatial analysis in the apprehension of an environmental problem such the waste management and more generally in the urban management.

Urban solid waste generation and disposal in Mexico: a case study.

PubMed

Buenrostro, O; Bocco, G; Bernache, G

2001-04-01

The adequate management of municipal solid waste in developing countries is difficult because of the scarcity of studies about their composition. This paper analyses the composition of urban solid waste (USW) in the city of Morelia, Michoacán, Mexico. Residential and non-residential waste sources were sampled, and a structured interview was made to evaluate the socioeconomic characteristics of the studied area. Also, to determine the seasonal patterns of solid waste generation and the efficiency level of the collection service, quantification of solid waste deposited in the dumping ground was measured. Our results show that the recorded amount of SW deposited in the municipal dumping-ground is less than the estimated amount of SW generated; for this reason, the former amount is not recommended as an unbiased indicator for planning public waste collection services. It is essential that dumping-grounds are permanently monitored and that the incoming waste be weighed in order to have a more efficient record of USW deposited in the dumping-ground per day; these data are fundamental for developing adequate managing strategies.

Trade study for water and waste management concepts. Task 7: Support special analysis. [cost analysis of life support systems for waste utilization during space missions

NASA Technical Reports Server (NTRS)

1975-01-01

Cost analyses and tradeoff studies are given for waste management in the Space Station, Lunar Surface Bases, and interplanetary space missions. Crew drinking water requirements are discussed and various systems to recycle water are examined. The systems were evaluated for efficiency and weight savings. The systems considered effective for urine water recovery were vapor compression, flash evaporation, and air evaporation with electrolytic pretreatment. For wash water recovery, the system of multifiltration was selected. A wet oxidation system, which can process many kinds of wastes, is also considered.

The Management of the Radioactive Waste Generated by Cernavoda NPP, Romania, an Example of International Cooperation - 13449

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barariu, Gheorghe

2013-07-01

The design criteria and constraints for the development of the management strategy for radioactive waste generated from operating and decommissioning of CANDU Nuclear Units from Cernavoda NPP in Romania, present many specific aspects. The main characteristics of CANDU type waste are its high concentrations of tritium and radiocarbon. Also, the existing management strategy for radioactive waste at Cernavoda NPP provides no treatment or conditioning for radioactive waste disposal. These characteristics embodied a challenging effort, in order to select a proper strategy for radioactive waste management at present, when Romania is an EU member and a signatory country of the Jointmore » Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. The helping of advanced countries in radioactive waste management, directly or into the frame of the international organizations, like IAEA, become solve the aforementioned challenges at adequate level. (authors)« less

Occupational Exposure to Infection: A study on Healthcare Waste Handlers of a Tertiary Care Hospital in South India.

PubMed

Shivalli, Siddharudha; Sowmyashree, H

2015-11-01

Occupational exposure to infection is an important public health concern. Such accidents are associated with a few, but pose significant risk to worker's health, family and the community. 1) To assess the knowledge and attitude of waste handlers regarding healthcare waste management in tertiary care hospital of Mangalore. 2) To assess the occupational risk of exposure to infection in their work setting. A cross-sectional study was conducted among healthcare waste handlers (involved in collection, storage and safe disposal) in a tertiary care hospital of Mangalore, India. A semi-structured and pre-tested proforma was used to assess respondents' knowledge and percentage score was calculated based on a scoring system. Chi square and independent sample t tests were applied to judge the association of study variables with knowledge and occupational risk of infection. A total of 43 healthcare waste handlers participated in the study and all were females. Almost half of them had poor knowledge (< 50% score) about healthcare waste management. As much as 41.8% of them had exposure to healthcare waste and 'needle stick injury' was the most common type. Age, literacy and experience did not significantly (p>0.05) influence the knowledge and occupational risk of infection. Respondents' knowledge regarding healthcare waste management was unsatisfactory. They were at high risk of occupational exposure to infection. It emphasizes the need of refresher training and reinforcement of personal protection measures in their work setting. © Journal of the Association of Physicians of India 2011.

40 CFR 60.2899 - What is a waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What is a waste management plan? 60.2899 Section 60.2899 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Management Plan § 60.2899 What is a waste management plan? A waste management plan is a written plan that...

Web-GIS oriented systems viability for municipal solid waste selective collection optimization in developed and transient economies.

PubMed

Rada, E C; Ragazzi, M; Fedrizzi, P

2013-04-01

Municipal solid waste management is a multidisciplinary activity that includes generation, source separation, storage, collection, transfer and transport, processing and recovery, and, last but not least, disposal. The optimization of waste collection, through source separation, is compulsory where a landfill based management must be overcome. In this paper, a few aspects related to the implementation of a Web-GIS based system are analyzed. This approach is critically analyzed referring to the experience of two Italian case studies and two additional extra-European case studies. The first case is one of the best examples of selective collection optimization in Italy. The obtained efficiency is very high: 80% of waste is source separated for recycling purposes. In the second reference case, the local administration is going to be faced with the optimization of waste collection through Web-GIS oriented technologies for the first time. The starting scenario is far from an optimized management of municipal solid waste. The last two case studies concern pilot experiences in China and Malaysia. Each step of the Web-GIS oriented strategy is comparatively discussed referring to typical scenarios of developed and transient economies. The main result is that transient economies are ready to move toward Web oriented tools for MSW management, but this opportunity is not yet well exploited in the sector. Copyright © 2013 Elsevier Ltd. All rights reserved.

Thirty-year solid waste generation forecast for facilities at SRS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-07-01

The information supplied by this 30-year solid waste forecast has been compiled as a source document to the Waste Management Environmental Impact Statement (WMEIS). The WMEIS will help to select a sitewide strategic approach to managing present and future Savannah River Site (SRS) waste generated from ongoing operations, environmental restoration (ER) activities, transition from nuclear production to other missions, and decontamination and decommissioning (D&D) programs. The EIS will support project-level decisions on the operation of specific treatment, storage, and disposal facilities within the near term (10 years or less). In addition, the EIS will provide a baseline for analysis ofmore » future waste management activities and a basis for the evaluation of the specific waste management alternatives. This 30-year solid waste forecast will be used as the initial basis for the EIS decision-making process. The Site generates and manages many types and categories of waste. With a few exceptions, waste types are divided into two broad groups-high-level waste and solid waste. High-level waste consists primarily of liquid radioactive waste, which is addressed in a separate forecast and is not discussed further in this document. The waste types discussed in this solid waste forecast are sanitary waste, hazardous waste, low-level mixed waste, low-level radioactive waste, and transuranic waste. As activities at SRS change from primarily production to primarily decontamination and decommissioning and environmental restoration, the volume of each waste s being managed will change significantly. This report acknowledges the changes in Site Missions when developing the 30-year solid waste forecast.« less

Vermicomposting as manure management strategy for urban small-holder animal farms – Kampala case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lalander, Cecilia Helena, E-mail: cecilia.lalander@slu.se; Komakech, Allan John; Department of Agricultural & Bio-systems Engineering, Makerere University, Kampala

Highlights: • Poor manure management can increase burden of disease and environmental impact. • A low-maintenance vermicompost reactor was set-up in Kampala, Uganda. • High material reduction (45.9%) and waste-to-biomass conversion (3.6% on a TS basis). • Five year return on investment of 275% of system in Uganda. • Technically and economically viable system for improved urban manure management. - Abstract: Inadequate organic waste management can contribute to the spread of diseases and have negative impacts on the environment. Vermicomposting organic waste could have dual beneficial effects by generating an economically viable animal feed protein in the form of wormmore » biomass, while alleviating the negative effects of poor organic waste management. In this study, a low-maintenance vermicomposting system was evaluated as manure and food waste management system for small-holder farmers. A vermicomposting system using the earthworm species Eudrilus eugeniae and treating cow manure and food waste was set up in Kampala, Uganda, and monitored for 172 days. The material degradation and protein production rates were evaluated after 63 days and at the end of the experiment. The material reduction was 45.9% and the waste-to-biomass conversion rate was 3.5% in the vermicomposting process on a total solids basis. A possible increase in the conversion rate could be achieved by increasing the frequency of worm harvesting. Vermicomposting was found to be a viable manure management method in small-scale urban animal agriculture; the return of investment was calculated to be 280% for treating the manure of a 450 kg cow. The vermicompost was not sanitised, although hygiene quality could be improved by introducing a post-stabilisation step in which no fresh material is added. The value of the animal feed protein generated in the process can act as an incentive to improve current manure management strategies.« less

Clinical solid waste management practices and its impact on human health and environment - A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hossain, Md. Sohrab; Santhanam, Amutha; Nik Norulaini, N.A.

2011-04-15

Research highlights: > Appropriate waste management technology for safe handling and disposal of clinical solid waste. > Infectious risk assessment on unsafe handling of clinical solid waste. > Recycling-reuse program of clinical solid waste materials. > Effective sterilization technology to reduce exposure of infectious risk. - Abstract: The management of clinical solid waste (CSW) continues to be a major challenge, particularly, in most healthcare facilities of the developing world. Poor conduct and inappropriate disposal methods exercised during handling and disposal of CSW is increasing significant health hazards and environmental pollution due to the infectious nature of the waste. This articlemore » summarises a literature review into existing CSW management practices in the healthcare centers. The information gathered in this paper has been derived from the desk study of open literature survey. Numerous researches have been conducted on the management of CSW. Although, significant steps have been taken on matters related to safe handling and disposal of the clinical waste, but improper management practice is evident from the point of initial collection to the final disposal. In most cases, the main reasons of the mismanagement of CSW are the lack of appropriate legislation, lack of specialized clinical staffs, lack of awareness and effective control. Furthermore, most of the healthcare centers of the developing world have faced financial difficulties and therefore looking for cost effective disposal methods of clinical waste. This paper emphasizes to continue the recycle-reuse program of CSW materials after sterilization by using supercritical fluid carbon dioxide (SF-CO2) sterilization technology at the point of initial collection. Emphasis is on the priority to inactivate the infectious micro-organisms in CSW. In that case, waste would not pose any threat to healthcare workers. The recycling-reuse program would be carried out successfully with the non-specialized clinical staffs. Therefore, the adoption of SF-CO2 sterilization technology in management of clinical solid waste can reduce exposure to infectious waste, decrease labor, lower costs, and yield better compliance with regulatory. Thus healthcare facilities can both save money and provide a safe environment for patients, healthcare staffs and clinical staffs.« less

Waste management system

NASA Technical Reports Server (NTRS)

Sauer, R. L.; Jorgensen, G. K.

1975-01-01

The function of the waste management system was to control the disposition of solid and liquid wastes and waste stowage gases. The waste management system consisting of a urine subsystem and a fecal subsystem is described in detail and its overall performance is evaluated. Recommendations for improvement are given.

Turning a hazardous waste lagoon into reclaimed land for wildlife management: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leong, A.K.

Brownfields are turning back to green. This paper presents a case study of a former dump site for hazardous waste that has been remediated and will be developed into an enhanced wildlife management habitat. This successful remediation case combined various investigations, remedial designs, risk assessments, ecological studies, and engineering practices. 3 refs., 1 fig., 1 tab.

Tribal Decisions-Makers Guide to Solid Waste Management: Chapter 2 - Developing Solid Waste Management Plans

EPA Pesticide Factsheets

Solid waste management plans offer a host of benefits for tribes and Alaskan Native villages. Through the preparation of these plans, you can assess your cur-rent and future waste management needs, set priorities, and allocate resources accordingly.

Greening MSW management systems by saving footprint: The contribution of the waste transportation.

PubMed

Peri, G; Ferrante, P; La Gennusa, M; Pianello, C; Rizzo, G

2018-08-01

Municipal solid waste (MSW) management constitutes a highly challenging issue to cope with in order of moving towards more sustainable urban policies. Despite new Standards call for recycling and reusing materials contained in the urban waste, several municipalities still use landfilling as a waste disposal method. Other than the environmental pressure exerted by these plants, waste transportation from the collection points to the landfill needs a specific attention to correctly assess the whole burden of the waste management systems. In this paper, the Ecological Footprint (EF) indicator is applied to the actual MSW of the city of Palermo (Sicily). Results show that the effects produced by the involved transportation vehicles are not negligible, compared to those generated by the other segments of the waste management system. This issue is further deepened by analysing the role of transportation in an upgraded waste management system that is represented by the newly designed waste management plan of Palermo. The computed saved ecological footprint is used here for suitably comparing the environmental performances of the MSW system in both scenarios. Finally, the suitability of the EF method to address not only complete waste management plans but also single segments of the waste management system, is also discussed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Production patterns of packaging waste categories generated at typical Mediterranean residential building worksites.

PubMed

González Pericot, N; Villoria Sáez, P; Del Río Merino, M; Liébana Carrasco, O

2014-11-01

The construction sector is responsible for around 28% of the total waste volume generated in Europe, which exceeds the amount of household waste. This has led to an increase of different research studies focusing on construction waste quantification. However, within the research studies made, packaging waste has been analyzed to a limited extent. This article focuses on the packaging waste stream generated in the construction sector. To this purpose current on-site waste packaging management has been assessed by monitoring ten Mediterranean residential building works. The findings of the experimental data collection revealed that the incentive measures implemented by the construction company to improve on-site waste sorting failed to achieve the intended purpose, showing low segregation ratios. Subsequently, through an analytical study the generation patterns for packaging waste are established, leading to the identification of the prevailing kinds of packaging and the products responsible for their generation. Results indicate that plastic waste generation maintains a constant trend throughout the whole construction process, while cardboard becomes predominant towards the end of the construction works with switches and sockets from the electricity stage. Understanding the production patterns of packaging waste will be beneficial for adapting waste management strategies to the identified patterns for the specific nature of packaging waste within the context of construction worksites. Copyright © 2014 Elsevier Ltd. All rights reserved.

Material and energy recovery in integrated waste management systems: a life-cycle costing approach.

PubMed

Massarutto, Antonio; de Carli, Alessandro; Graffi, Matteo

2011-01-01

A critical assumption of studies assessing comparatively waste management options concerns the constant average cost for selective collection regardless the source separation level (SSL) reached, and the neglect of the mass constraint. The present study compares alternative waste management scenarios through the development of a desktop model that tries to remove the above assumption. Several alternative scenarios based on different combinations of energy and materials recovery are applied to two imaginary areas modelled in order to represent a typical Northern Italian setting. External costs and benefits implied by scenarios are also considered. Scenarios are compared on the base of the full cost for treating the total waste generated in the area. The model investigates the factors that influence the relative convenience of alternative scenarios. Copyright © 2011 Elsevier Ltd. All rights reserved.

Results of a hospital waste survey in private hospitals in Fars province, Iran

DOE Office of Scientific and Technical Information (OSTI.GOV)

Askarian, Mehrdad; Vakili, Mahmood; Kabir, Gholamhosein

2004-07-01

Hospital waste is considered dangerous because it may possess pathogenic agents and can cause undesirable effects on human health and the environment. In Iran, neither rules have been compiled nor does exact information exist regarding hospital waste management. The survey presented in this article was carried out in all 15 private hospitals of Fars province (Iran) from the total numbers of 50 governmental and private hospitals located in this province, in order to determine the amount of different kinds of waste produced and the present situation of waste management. The results indicated that the waste generation rate is 4.45 kg/bed/day,more » which includes 1830 kg (71.44%) of domestic waste, 712 kg (27.8%) of infectious waste, and 19.6 kg (0.76%) of sharps. Segregation of the different types of waste is not carried out perfectly. Two (13.3%) of the hospitals use containers without lids for on-site transport of wastes. Nine (60%) of the hospitals are equipped with an incinerator and six of them (40%) have operational problems with the incinerators. In all hospitals municipal workers transport waste outside the hospital premises daily or at the most on alternative days. In the hospitals under study, there aren't any training courses about hospital waste management and the hazards associated with them. The training courses that are provided are either ineffective or unsuitable. Performing extensive studies all over the country, compiling and enacting rules, establishing standards and providing effective personnel training are the main challenges for the concerned authorities and specialists in this field.« less

The Integrated Waste Tracking System - A Flexible Waste Management Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Robert Stephen

2001-02-01

The US Department of Energy (DOE) Idaho National Engineering and Environmental Laboratory (INEEL) has fully embraced a flexible, computer-based tool to help increase waste management efficiency and integrate multiple operational functions from waste generation through waste disposition while reducing cost. The Integrated Waste Tracking System (IWTS)provides comprehensive information management for containerized waste during generation,storage, treatment, transport, and disposal. The IWTS provides all information necessary for facilities to properly manage and demonstrate regulatory compliance. As a platformindependent, client-server and Web-based inventory and compliance system, the IWTS has proven to be a successful tracking, characterization, compliance, and reporting tool that meets themore » needs of both operations and management while providing a high level of management flexibility.« less

Web-GIS oriented systems viability for municipal solid waste selective collection optimization in developed and transient economies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rada, E.C., E-mail: Elena.Rada@ing.unitn.it; Ragazzi, M.; Fedrizzi, P.

Highlights: ► As an appropriate solution for MSW management in developed and transient countries. ► As an option to increase the efficiency of MSW selective collection. ► As an opportunity to integrate MSW management needs and services inventories. ► As a tool to develop Urban Mining actions. - Abstract: Municipal solid waste management is a multidisciplinary activity that includes generation, source separation, storage, collection, transfer and transport, processing and recovery, and, last but not least, disposal. The optimization of waste collection, through source separation, is compulsory where a landfill based management must be overcome. In this paper, a few aspectsmore » related to the implementation of a Web-GIS based system are analyzed. This approach is critically analyzed referring to the experience of two Italian case studies and two additional extra-European case studies. The first case is one of the best examples of selective collection optimization in Italy. The obtained efficiency is very high: 80% of waste is source separated for recycling purposes. In the second reference case, the local administration is going to be faced with the optimization of waste collection through Web-GIS oriented technologies for the first time. The starting scenario is far from an optimized management of municipal solid waste. The last two case studies concern pilot experiences in China and Malaysia. Each step of the Web-GIS oriented strategy is comparatively discussed referring to typical scenarios of developed and transient economies. The main result is that transient economies are ready to move toward Web oriented tools for MSW management, but this opportunity is not yet well exploited in the sector.« less

Understanding the perceptions, roles and interactions of stakeholder networks managing health-care waste: A case study of the Gaza Strip.

PubMed

Caniato, M; Tudor, T; Vaccari, M

2015-01-01

The sustainable management of waste requires a holistic approach involving a range of stakeholders. What can often be difficult is to understand the manner in which different types of stakeholder networks are composed and work, and how best to enhance their effectiveness. Using social network analysis and stakeholder analysis of healthcare waste management stakeholders in the case study region of the Gaza Strip, this study aimed to understand and examine the manner in which the networks functioned. The Ministry of Health was found to be the most important stakeholder, followed by municipalities and solid waste management councils. Some international agencies were also mentioned, with specific roles, while other local institutions had a limited influence. Finally while health-care facilities had a strong interest in waste management, they were generally poorly informed and had limited links to each other. The manner in which the networks operated was complicated and influenced by differences in perception, sharing of information, access to finance and levels of awareness. The lack of a clear legal framework generated various mistakes about roles and responsibilities in the system, and evidently regulation was not an effective driver for improvement. Finally stakeholders had different priorities according to the waste management issues they were involved with, however segregation at the source was identified as a key requirement by most. Areas for improving the effectiveness of the networks are suggested. The analysis utilized an innovative methodology, which involved a large number of stakeholders. Such an approach served to raise interest and awareness at different levels (public authorities, health providers, supporting actors, others), stimulate the discussion about the adoption of specific policies, and identify the effective way forward. Copyright © 2014 Elsevier Ltd. All rights reserved.

Application of TOPSIS and VIKOR improved versions in a multi criteria decision analysis to develop an optimized municipal solid waste management model.

PubMed

Aghajani Mir, M; Taherei Ghazvinei, P; Sulaiman, N M N; Basri, N E A; Saheri, S; Mahmood, N Z; Jahan, A; Begum, R A; Aghamohammadi, N

2016-01-15

Selecting a suitable Multi Criteria Decision Making (MCDM) method is a crucial stage to establish a Solid Waste Management (SWM) system. Main objective of the current study is to demonstrate and evaluate a proposed method using Multiple Criteria Decision Making methods (MCDM). An improved version of Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) applied to obtain the best municipal solid waste management method by comparing and ranking the scenarios. Applying this method in order to rank treatment methods is introduced as one contribution of the study. Besides, Viekriterijumsko Kompromisno Rangiranje (VIKOR) compromise solution method applied for sensitivity analyses. The proposed method can assist urban decision makers in prioritizing and selecting an optimized Municipal Solid Waste (MSW) treatment system. Besides, a logical and systematic scientific method was proposed to guide an appropriate decision-making. A modified TOPSIS methodology as a superior to existing methods for first time was applied for MSW problems. Applying this method in order to rank treatment methods is introduced as one contribution of the study. Next, 11 scenarios of MSW treatment methods are defined and compared environmentally and economically based on the waste management conditions. Results show that integrating a sanitary landfill (18.1%), RDF (3.1%), composting (2%), anaerobic digestion (40.4%), and recycling (36.4%) was an optimized model of integrated waste management. An applied decision-making structure provides the opportunity for optimum decision-making. Therefore, the mix of recycling and anaerobic digestion and a sanitary landfill with Electricity Production (EP) are the preferred options for MSW management. Copyright © 2015 Elsevier Ltd. All rights reserved.

Frequent Questions About Universal Waste

EPA Pesticide Factsheets

Frequent questions such as Who is affected by the universal waste regulations? What is “mercury-containing equipment”? How are waste batteries managed under universal waste? How are waste pesticides managed under universal waste?

Municipal solid waste management planning considering greenhouse gas emission trading under fuzzy environment.

PubMed

Zhang, Xiaodong; Huang, Gordon

2014-03-15

Waste management activities can release greenhouse gases (GHGs) to the atmosphere, intensifying global climate change. Mitigation of the associated GHG emissions is vital and should be considered within integrated municipal solid waste (MSW) management planning. In this study, a fuzzy possibilistic integer programming (FPIM) model has been developed for waste management facility expansion and waste flow allocation planning with consideration of GHG emission trading in an MSW management system. It can address the interrelationships between MSW management planning and GHG emission control. The scenario of total system GHG emission control is analyzed for reflecting the feature that GHG emission credits may be tradable. An interactive solution algorithm is used to solve the FPIM model based on the uncertainty-averse preferences of decision makers in terms of p-necessity level, which represents the certainty degree of the imprecise objective. The FPIM model has been applied to a hypothetical MSW planning problem, where optimal decision schemes for facility expansion and waste flow allocation have been achieved with consideration of GHG emission control. The results indicate that GHG emission credit trading can decrease total system cost through re-allocation of GHG emission credits within the entire MSW management system. This will be helpful for decision makers to effectively determine the allowable GHG emission permits in practices. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of an analytical method for quantitative comparison of the e-waste management systems in Thailand, Laos, and China.

PubMed

Liang, Li; Sharp, Alice

2016-11-01

This study employed a set of quantitative criteria to analyse the three parameters; namely policy, process, and practice; of the respective e-waste management systems adopted in Thailand, Laos, and China. Questionnaire surveys were conducted to determine the current status of the three parameters in relation to mobile phones. A total of five, three, and six variables under Policy (P 1 ), Process (P 2 ), and Practice (P 3 ), respectively, were analysed and their weighted averages were calculated. The results showed that among the three countries surveyed, significant differences at p<0.01 were observed in all the P 1 , P 2 , and P 3 variables, except P 305 (sending e-waste to recovery centres) and P 306 (treating e-waste by retailers themselves). Based on the quantitative method developed in this study, Laos' e-waste management system received the highest scores in both P 1 average (0.130) and P 3 average (0.129). However, in the combined P total , China scored the highest (0.141), followed by Laos (0.132) and Thailand (0.121). This method could be used to assist decision makers in performing quantitative analysis of complex issues associating with e-waste management in a country. © The Author(s) 2016.

Improving the medical records department processes by lean management.

PubMed

Ajami, Sima; Ketabi, Saeedeh; Sadeghian, Akram; Saghaeinnejad-Isfahani, Sakine

2015-01-01

Lean management is a process improvement technique to identify waste actions and processes to eliminate them. The benefits of Lean for healthcare organizations are that first, the quality of the outcomes in terms of mistakes and errors improves. The second is that the amount of time taken through the whole process significantly improves. The purpose of this paper is to improve the Medical Records Department (MRD) processes at Ayatolah-Kashani Hospital in Isfahan, Iran by utilizing Lean management. This research was applied and an interventional study. The data have been collected by brainstorming, observation, interview, and workflow review. The study population included MRD staff and other expert staff within the hospital who were stakeholders and users of the MRD. The MRD were initially taught the concepts of Lean management and then formed into the MRD Lean team. The team then identified and reviewed the current processes subsequently; they identified wastes and values, and proposed solutions. The findings showed that the MRD units (Archive, Coding, Statistics, and Admission) had 17 current processes, 28 wastes, and 11 values were identified. In addition, they offered 27 comments for eliminating the wastes. The MRD is the critical department for the hospital information system and, therefore, the continuous improvement of its services and processes, through scientific methods such as Lean management, are essential. The study represents one of the few attempts trying to eliminate wastes in the MRD.

Electronic waste management approaches: An overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiddee, Peeranart; Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, Mawson Lakes Campus, Adelaide, SA 5095; Naidu, Ravi, E-mail: ravi.naidu@crccare.com

2013-05-15

Highlights: ► Human toxicity of hazardous substances in e-waste. ► Environmental impacts of e-waste from disposal processes. ► Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) to and solve e-waste problems. ► Key issues relating to tools managing e-waste for sustainable e-waste management. - Abstract: Electronic waste (e-waste) is one of the fastest-growing pollution problems worldwide given the presence if a variety of toxic substances which can contaminate the environment and threaten human health, if disposal protocols are not meticulously managed. This paper presents an overview of toxic substances present inmore » e-waste, their potential environmental and human health impacts together with management strategies currently being used in certain countries. Several tools including Life Cycle Assessment (LCA), Material Flow Analysis (MFA), Multi Criteria Analysis (MCA) and Extended Producer Responsibility (EPR) have been developed to manage e-wastes especially in developed countries. The key to success in terms of e-waste management is to develop eco-design devices, properly collect e-waste, recover and recycle material by safe methods, dispose of e-waste by suitable techniques, forbid the transfer of used electronic devices to developing countries, and raise awareness of the impact of e-waste. No single tool is adequate but together they can complement each other to solve this issue. A national scheme such as EPR is a good policy in solving the growing e-waste problems.« less

77 FR 59879 - Idaho: Incorporation by Reference of Approved State Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

...: Incorporation by Reference of Approved State Hazardous Waste Management Program AGENCY: Environmental Protection... ``Approved State Hazardous Waste Management Programs,'' Idaho's authorized hazardous waste program. The EPA... Federal Register, the EPA is codifying and incorporating by reference the State's hazardous waste program...

77 FR 46994 - Oklahoma: Incorporation by Reference of State Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-07

... State regulations that are authorized and that the EPA will enforce under the Solid Waste Disposal Act...: Incorporation by Reference of State Hazardous Waste Management Program AGENCY: Environmental Protection Agency... ``Approved State Hazardous Waste Management Programs'', Oklahoma's authorized hazardous waste program. The...

77 FR 29275 - Oklahoma: Incorporation by Reference of State Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-17

... State regulations that are authorized and that the EPA will enforce under the Solid Waste Disposal Act...: Incorporation by Reference of State Hazardous Waste Management Program AGENCY: Environmental Protection Agency... ``Approved State Hazardous Waste Management Programs'', Oklahoma's authorized hazardous waste program. The...

75 FR 36609 - Oklahoma: Incorporation by Reference of State Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

...: Incorporation by Reference of State Hazardous Waste Management Program AGENCY: Environmental Protection Agency... ``Approved State Hazardous Waste Management Programs'', Oklahoma's authorized hazardous waste program. The... State regulations that are authorized and that the EPA will enforce under the Solid Waste Disposal Act...

77 FR 3224 - New Mexico: Incorporation by Reference of State Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-23

... Mexico: Incorporation by Reference of State Hazardous Waste Management Program AGENCY: Environmental... entitled ``Approved State Hazardous Waste Management Programs,'' New Mexico's authorized hazardous waste... of the State regulations that are authorized and that the EPA will enforce under the Solid Waste...

Waste management and recycling in the former Soviet Union: the City of Bishkek, Kyrgyz Republic (Kyrgyzstan).

PubMed

Sim, Natasha M; Wilson, David C; Velis, Costas A; Smith, Stephen R

2013-10-01

The UN-Habitat Integrated Sustainable Waste Management (ISWM) benchmarking methodology was applied to profile the physical and governance features of municipal solid waste (MSW) management in the former Soviet Union city of Bishkek, capital of the Kyrgyz Republic. Most of the ISWM indicators were in the expected range for a low-income city when compared with 20 reference cities. Approximately 240,000 t yr(-1) of MSW is generated in Bishkek (equivalent to 200 kg capita(-1) yr(-1)); collection coverage is over 80% and 90% of waste disposed goes to semi-controlled sites operating with minimal environmental standards. The waste composition was a distinctive feature, with relatively high paper content (20-27% wt.) and intermediate organic content (30-40% wt.). The study provides the first quantitative estimates of informal sector recycling, which is currently unrecognised by the city authorities. Approximately 18% wt. of generated MSW is recycled, representing an estimated annual saving to the city authorities of US$0.7-1.1 million in avoided collection/disposal costs. The waste management system is controlled by a centralised municipal waste enterprise (Tazalyk); therefore, institutional coherence is high relative to lower-middle and low-income cities. However, performance on other governance factors, such as inclusivity and financial sustainability, is variable. Future priorities in Bishkek include extending collection to unserved communities; improving landfill standards; increasing recycling rates through informal sector cooperation; improving data availability; and engaging all stakeholders in waste management strategy decisions. Extending the scope and flexibility of the ISWM protocol is recommended to better represent the variation in conditions that occur in waste management systems in practice.

Municipal solid waste development phases: Evidence from EU27.

PubMed

Vujić, Goran; Gonzalez-Roof, Alvaro; Stanisavljević, Nemanja; Ragossnig, Arne M

2015-12-01

Many countries in the European Union (EU) have very developed waste management systems. Some of its members have managed to reduce their landfilled waste to values close to zero during the last decade. Thus, European Union legislation is very stringent regarding waste management for their members and candidate countries, too. This raises the following questions: Is it possible for developing and developed countries to comply with the European Union waste legislation, and under what conditions? How did waste management develop in relation to the economic development in the countries of the European Union? The correlation between waste management practices and economic development was analysed for 27 of the European Union Member States for the time period between 1995 and 2007. In addition, a regression analysis was performed to estimate landfilling of waste in relation to gross domestic product for every country. The results showed a strong correlation between the waste management variables and the gross domestic product of the EU27 members. The definition of the municipal solid waste management development phases followed a closer analysis of the relation between gross domestic product and landfilled waste. The municipal solid waste management phases are characterised by high landfilling rates at low gross domestic product levels, and landfilling rates near zero at high gross domestic product levels. Hence the results emphasize the importance of wider understanding of what is required for developing countries to comply with the European Union initiatives, and highlight the importance of allowing developing countries to make their own paths of waste management development. © The Author(s) 2015.

75 FR 20942 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Removal of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-22

... of the waste generation and management information for saccharin and its salts, which demonstrate... partnership with the States, biennially collects information regarding the generation, management, and final... Based on the Available Toxicological Information and Waste Generation and Management Information for...

77 FR 60919 - Tennessee: Final Authorization of State Hazardous Waste Management Program Revisions

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-05

...: Final Authorization of State Hazardous Waste Management Program Revisions AGENCY: Environmental..., Division of Solid Waste Management, 5th Floor, L & C Tower, 401 Church Street, Nashville, Tennessee 37243... RCRA hazardous waste management program. We granted authorization for changes to Tennessee's program on...

Oak Ridge Reservation Waste Management Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, J.W.

1995-02-01

This report presents the waste management plan for the Oak Ridge Reservation facilities. The primary purpose is to convey what facilities are being used to manage wastes, what forces are acting to change current waste management systems, and what plans are in store for the coming fiscal year.

40 CFR 60.2060 - When must I submit my waste management plan?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false When must I submit my waste management plan? 60.2060 Section 60.2060 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Management Plan § 60.2060 When must I submit my waste management plan? You must submit a waste management...

40 CFR 60.2060 - When must I submit my waste management plan?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false When must I submit my waste management plan? 60.2060 Section 60.2060 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Management Plan § 60.2060 When must I submit my waste management plan? You must submit a waste management...

40 CFR 60.2060 - When must I submit my waste management plan?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false When must I submit my waste management plan? 60.2060 Section 60.2060 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Management Plan § 60.2060 When must I submit my waste management plan? You must submit a waste management...

Let's Waste Less Waste, Level 4. Teacher Guide. Operation Waste Watch.

ERIC Educational Resources Information Center

Virginia State Dept. of Waste Management, Richmond. Div. of Litter & Recycling.

Operation Waste Watch is a series of seven sequential learning units which addresses the subject of litter control and solid waste management. Each unit may be used in a variety of ways, depending on the needs and schedules of individual schools, and may be incorporated into various social studies, science, language arts, health, mathematics, and…

Medical waste management in Jordan: A study at the King Hussein Medical Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oweis, Rami; Al-Widyan, Mohamad; Al-Limoon, Ohood

2005-07-01

As in many other developing countries, the generation of regulated medical waste (RMW) in Jordan has increased significantly over the last few decades. Despite the serious impacts of RMW on humans and the environment, only minor attention has been directed to its proper handling and disposal. This study was conducted in the form of a case study at one of Jordan's leading medical centers, namely, the King Hussein Medical Center (KHMC). Its purpose was to report on the current status of medical waste management at KHMC and propose possible measures to improve it. In general, it was found that themore » center's administration was reasonably aware of the importance of medical waste management and practiced some of the measures to adequately handle waste generated at the center. However, it was also found that significant voids were present that need to be addressed in the future including efficient segregation, the use of coded and colored bags, better handling and transfer means, and better monitoring and tracking techniques, as well as the need for training and awareness programs for the personnel.« less

The radioactive waste management policy and practice in the Czech Republic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucerka, M.

1996-12-31

In recent period, the new Czech Atomic Law is in the final stage of preparation, and the author expects that Parliament of the Czech Republic will approve it in the first half of the year 1996. Partly the law deals with new distribution of responsibilities among bodies involved in utilization of nuclear energy and ionizing radiation, the state and local authorities. The new provisions include also radioactive waste management activities. These provisions clarify the relations between radioactive waste generators and state, and define explicitly duties of waste generators. One of the most important duties is to cover all expenses formore » radioactive waste management now and in the future, including radioactive waste disposal and decommissioning of nuclear facilities. The law establishes radioactive waste management and decommissioning funds and the new, on waste generators independent radioactive waste management organization, controlled by state, to ensure the safety of inhabitants and the environment, and a optimization of expenses. Parallel to the preparation of the law, the Ministry of Industry and Trade prepares drafts of a statute of the radioactive waste management organization and its control board, and of the methodology and rules of management the radioactive waste fund. First drafts of these documents are expected to be complete in January 1996. The paper will describe recent practice and policy of the radioactive waste management including uranium mining and milling tailings, amounts of waste and its activities, economical background, and safety. A special attention will be paid to description of expected changes in connection with the new Atomic Law and expected steps and time schedule of reorganization of the radioactive waste management structure in the Czech Republic.« less

EPA office of solid waste (OSW) report to Congress

DOE Office of Scientific and Technical Information (OSTI.GOV)

Derkics, D.

1996-12-31

An EPA Office of Solid Waste Report to Congress is presented in outline form. The following topics are discussed: special waste chronology; statutory hazardous waste exemption; 1988 report to Congress findings; 1993 regulatory determination; current (1996), regulatory status of fossil fuel combustion wastes; co-management study; Electric Power Research Institute (EPRI) activities; EPRI coal ash field study sites; oil ash total combustion; fossil fuel combustion; current EPA activities; and Federal Register Notice.

Community mobilization and household level waste management for dengue vector control in Gampaha district of Sri Lanka; an intervention study.

PubMed

Abeyewickreme, W; Wickremasinghe, A R; Karunatilake, K; Sommerfeld, J; Axel, Kroeger

2012-12-01

Waste management through community mobilization to reduce breeding places at household level could be an effective and sustainable dengue vector control strategy in areas where vector breeding takes place in small discarded water containers. The objective of this study was to assess the validity of this assumption. An intervention study was conducted from February 2009 to February 2010 in the populous Gampaha District of Sri Lanka. Eight neighborhoods (clusters) with roughly 200 houses each were selected randomly from high and low dengue endemic areas; 4 of them were allocated to the intervention arm (2 in the high and 2 in the low endemicity areas) and in the same way 4 clusters to the control arm. A baseline household survey was conducted and entomological and sociological surveys were carried out simultaneously at baseline, at 3 months, at 9 months and at 15 months after the start of the intervention. The intervention programme in the treatment clusters consisted of building partnerships of local stakeholders, waste management at household level, the promotion of composting biodegradable household waste, raising awareness on the importance of solid waste management in dengue control and improving garbage collection with the assistance of local government authorities. The intervention and control clusters were very similar and there were no significant differences in pupal and larval indices of Aedes mosquitoes. The establishment of partnerships among local authorities was well accepted and sustainable; the involvement of communities and households was successful. Waste management with the elimination of the most productive water container types (bowls, tins, bottles) led to a significant reduction of pupal indices as a proxy for adult vector densities. The coordination of local authorities along with increased household responsibility for targeted vector interventions (in our case solid waste management due to the type of preferred vector breeding places) is vital for effective and sustained dengue control.

Community mobilization and household level waste management for dengue vector control in Gampaha district of Sri Lanka; an intervention study

PubMed Central

Abeyewickreme, W; Wickremasinghe, A R; Karunatilake, K; Sommerfeld, Johannes; Kroeger, Axel

2012-01-01

Introduction Waste management through community mobilization to reduce breeding places at household level could be an effective and sustainable dengue vector control strategy in areas where vector breeding takes place in small discarded water containers. The objective of this study was to assess the validity of this assumption. Methods An intervention study was conducted from February 2009 to February 2010 in the populous Gampaha District of Sri Lanka. Eight neighborhoods (clusters) with roughly 200 houses each were selected randomly from high and low dengue endemic areas; 4 of them were allocated to the intervention arm (2 in the high and 2 in the low endemicity areas) and in the same way 4 clusters to the control arm. A baseline household survey was conducted and entomological and sociological surveys were carried out simultaneously at baseline, at 3 months, at 9 months and at 15 months after the start of the intervention. The intervention programme in the treatment clusters consisted of building partnerships of local stakeholders, waste management at household level, the promotion of composting biodegradable household waste, raising awareness on the importance of solid waste management in dengue control and improving garbage collection with the assistance of local government authorities. Results The intervention and control clusters were very similar and there were no significant differences in pupal and larval indices of Aedes mosquitoes. The establishment of partnerships among local authorities was well accepted and sustainable; the involvement of communities and households was successful. Waste management with the elimination of the most productive water container types (bowls, tins, bottles) led to a significant reduction of pupal indices as a proxy for adult vector densities. Conclusion The coordination of local authorities along with increased household responsibility for targeted vector interventions (in our case solid waste management due to the type of preferred vector breeding places) is vital for effective and sustained dengue control. PMID:23318240

About the Managing and Transforming Waste Streams Tool

EPA Pesticide Factsheets

The Managing and Transforming Waste Streams Tool was developed by a team of zero waste consultants and solid waste program managers making informed observations from hands-on work in communities, with contributions from EPA.

76 FR 4823 - Hazardous Waste Management System; Identifying and Listing Hazardous Waste Exclusion

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-27

... Waste Management System; Identifying and Listing Hazardous Waste Exclusion AGENCY: Environmental... hazardous wastes. The Agency has decided to grant the petition based on an evaluation of waste-specific... excludes the petitioned waste from the requirements of hazardous waste regulations under the Resource...

40 CFR 60.55c - Waste management plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... plan. The owner or operator of an affected facility shall prepare a waste management plan. The waste management plan shall identify both the feasibility and the approach to separate certain components of solid waste from the health care waste stream in order to reduce the amount of toxic emissions from...

40 CFR 60.55c - Waste management plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... plan. The owner or operator of an affected facility shall prepare a waste management plan. The waste management plan shall identify both the feasibility and the approach to separate certain components of solid waste from the health care waste stream in order to reduce the amount of toxic emissions from...

Biomedical waste management in Ayurveda hospitals - current practices & future prospectives.

PubMed

Rajan, Renju; Robin, Delvin T; M, Vandanarani

2018-03-16

Biomedical waste management is an integral part of traditional and contemporary system of health care. The paper focuses on the identification and classification of biomedical wastes in Ayurvedic hospitals, current practices of its management in Ayurveda hospitals and its future prospective. Databases like PubMed (1975-2017 Feb), Scopus (1960-2017), AYUSH Portal, DOAJ, DHARA and Google scholar were searched. We used the medical subject headings 'biomedical waste' and 'health care waste' for identification and classification. The terms 'biomedical waste management', 'health care waste management' alone and combined with 'Ayurveda' or 'Ayurvedic' for current practices and recent advances in the treatment of these wastes were used. We made a humble attempt to categorize the biomedical wastes from Ayurvedic hospitals as the available data about its grouping is very scarce. Proper biomedical waste management is the mainstay of hospital cleanliness, hospital hygiene and maintenance activities. Current disposal techniques adopted for Ayurveda biomedical wastes are - sewage/drains, incineration and land fill. But these methods are having some merits as well as demerits. Our review has identified a number of interesting areas for future research such as the logical application of bioremediation techniques in biomedical waste management and the usage of effective micro-organisms and solar energy in waste disposal. Copyright © 2017 Transdisciplinary University, Bangalore and World Ayurveda Foundation. Published by Elsevier B.V. All rights reserved.

The opportunity of tracking food waste in school canteens: Guidelines for self-assessment.

PubMed

Derqui, Belén; Fernandez, Vicenc

2017-11-01

Reducing food waste is one of the key challenges of the food system and addressing it in the institutional catering industry can be a quick win. In particular, school canteens are a significant source of food waste and therefore embody a great opportunity to address food waste. The goal of our research is the development of guidelines for audit and self-assessment in measuring and managing food waste produced at school canteens. The purpose of the tool is to standardise food waste audits to be executed either by scholars, school staff or by catering companies with the objective of measuring and reducing food waste at schools. We performed a research among public and private schools and catering companies from which we obtained the key performance indicators to be measured and then pilot-tested the resulting tool in four schools with over 2900 pupil participants, measuring plate waste from over 10,000 trays. This tool will help managers in their efforts towards more sustainable organisations at the same time as the standardisation of food waste audits will provide researchers with comparable data. The study suggests that although there is low awareness on the amount of food wasted at school canteens, managers and staff are highly interested in the topic and would be willing to implement audits and reduction measures. The case study also showed that our tool is easy to implement and not disruptive. Copyright © 2017 Elsevier Ltd. All rights reserved.

Decommissioning the Romanian Water-Cooled Water-Moderated Research Reactor: New Environmental Perspective on the Management of Radioactive Waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barariu, G.; Giumanca, R.

2006-07-01

Pre-feasibility and feasibility studies were performed for decommissioning of the water-cooled water-moderated research reactor (WWER) located in Bucharest - Magurele, Romania. Using these studies as a starting point, the preferred safe management strategy for radioactive wastes produced by reactor decommissioning is outlined. The strategy must account for reactor decommissioning, as well as for the rehabilitation of the existing Radioactive Waste Treatment Plant and for the upgrade of the Radioactive Waste Disposal Facility at Baita-Bihor. Furthermore, the final rehabilitation of the laboratories and ecological reconstruction of the grounds need to be provided for, in accordance with national and international regulations. Inmore » accordance with IAEA recommendations at the time, the pre-feasibility study proposed three stages of decommissioning. However, since then new ideas have surfaced with regard to decommissioning. Thus, taking into account the current IAEA ideology, the feasibility study proposes that decommissioning of the WWER be done in one stage to an unrestricted clearance level of the reactor building in an Immediate Dismantling option. Different options and the corresponding derived preferred option for waste management are discussed taking into account safety measures, but also considering technical, logistical and economic factors. For this purpose, possible types of waste created during each decommissioning stage are reviewed. An approximate inventory of each type of radioactive waste is presented. The proposed waste management strategy is selected in accordance with the recommended international basic safety standards identified in the previous phase of the project. The existing Radioactive Waste Treatment Plant (RWTP) from the Horia Hulubei Institute for Nuclear Physics and Engineering (IFIN-HH), which has been in service with no significant upgrade since 1974, will need refurbishing due to deterioration, as well as upgrading in order to ensure the plant complies with current safety standards. This plant will also need to be adapted to treat wastes generated by WWER dismantling. The Baita-Bihor National Radioactive Waste Disposal Facility consists of two galleries in an abandoned uranium mine located in the central-western part of the Bihor Mountains in Transylvania. The galleries lie at a depth of 840 m. The facility requires a considerable overhaul. Several steps recommended for the upgrade of the facility are explored. Environmental concerns have lately become a crucial part of the radioactive waste management strategy. As such, all decisions must be made with great regard for land utilization around nuclear objectives. (authors)« less

75 FR 76691 - Oregon; Correction of Federal Authorization of the State's Hazardous Waste Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-09

...; Correction of Federal Authorization of the State's Hazardous Waste Management Program AGENCY: Environmental... to the State of Oregon's federally authorized RCRA hazardous waste management program. On January 7... changes the State of Oregon made to its federally authorized RCRA Hazardous Waste Management Program...

75 FR 918 - Oregon: Final Authorization of State Hazardous Waste Management Program Revision

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-07

... Authorization of State Hazardous Waste Management Program Revision AGENCY: Environmental Protection Agency (EPA... hazardous waste management program under the Resource Conservation and Recovery Act, as amended (RCRA). On... has decided that the revisions to the Oregon hazardous waste management program satisfy all of the...

Laboratory Waste Management. A Guidebook.

ERIC Educational Resources Information Center

American Chemical Society, Washington, DC.

A primary goal of the American Chemical Society Task Force on Laboratory Waste Management is to provide laboratories with the information necessary to develop effective strategies and training programs for managing laboratory wastes. This book is intended to present a fresh look at waste management from the laboratory perspective, considering both…

76 FR 63509 - Small Business Size Standards: Administrative and Support, Waste Management and Remediation Services

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-12

... Small Business Size Standards: Administrative and Support, Waste Management and Remediation Services... Standards: Administrative and Support, Waste Management and Remediation Services AGENCY: U.S. Small Business...) Sector 56, Administrative and Support, Waste Management and Remediation Services. As part of its ongoing...

Building Staff Competencies and Selecting Communications Methods for Waste Management Programs.

ERIC Educational Resources Information Center

Richardson, John G.

The Waste Management Institute provided in-service training to interested County Extension agents in North Carolina to enable them to provide leadership in developing and delivering a comprehensive county-level waste management program. Training included technical, economic, environmental, social, and legal aspects of waste management presented in…

Management of solid waste

NASA Astrophysics Data System (ADS)

Thompson, W. T.; Stinton, L. H.

1980-04-01

Compliance with the latest regulatory requirements addressing disposal of radioactive, hazardous, and sanitary solid waste criteria in the selection, design, and operation of solid waste management facilities. Due to the state of flux of these regulatory requirements from EPA and NRC, several waste management options were of solid waste. The current regulatory constraints and the design and operational requirements for construction of both storage and disposal facilities for use in management of DOE-ORO solid waste are highlighted. Capital operational costs are included for both disposal and storage options.

E-waste management and sustainability: a case study in Brazil.

PubMed

Azevedo, Luís Peres; da Silva Araújo, Fernando Gabriel; Lagarinhos, Carlos Alberto Ferreira; Tenório, Jorge Alberto Soares; Espinosa, Denise Crocce Romano

2017-11-01

The advancement of technology and development of new electronic and electrical equipment with a reduced life cycle has increased the need for the disposal of them (called Waste of Electric and Electronic Equipment or simply e-waste) due to defects presented during use, replacement of obsolete equipment, and ease of acquisition of new equipment. There is a lack of consumer awareness regarding the use, handling storage, and disposal of this equipment. In Brazil, the disposal of post-consumer waste is regulated by the National Solid Waste Policy, established by Law No. 12305 and regulated on the 23rd December 2010. Under this legislation, manufacturers and importers are required to perform a project for the Reverse Logistics of e-waste, though its implementation is not well defined. This work focuses on the verification of the sustainability of reverse logistics suggested by the legislation and the mandatory points, evaluating its costs and the possible financial gain with recycling of the waste. The management of reverse logistics and recycling of waste electrical and electronic equipment, or simply recycling of e-waste, as suggested by the government, will be the responsibility of the managing organization to be formed by the manufacturers/importers in Brazil.

Destined for indecision? A critical analysis of waste management practices in England from 1996 to 2013.

PubMed

Farmer, T D; Shaw, P J; Williams, I D

2015-05-01

European nations are compelled to reduce reliance on landfill as a destination for household waste, and should, in principle, achieve this goal with due recognition of the aims and principles of the waste hierarchy. Past research has predominantly focused on recycling, whilst interactions between changing waste destinies, causes and drivers of household waste management change, and potential consequences for the goal of the waste hierarchy are less well understood. This study analysed Local Authority Collected Waste (LACW) for England, at national, regional and sub-regional level, in terms of the destination of household waste to landfill, incineration and recycling. Information about waste partnerships, waste management infrastructure and collection systems was collected to help identify and explain changes in waste destinies. Since 1996, the proportion of waste landfilled in England has decreased, in tandem with increases in recycling and incineration. At the regional and sub-regional (Local Authority; LA) level, there have been large variations in the relative proportions of waste landfilled, incinerated and recycled or composted. Annual increases in the proportion of household waste incinerated were typically larger than increases in the proportion recycled. The observed changes took place in the context of legal and financial drivers, and the circumstances of individual LAs (e.g. landfill capacity) also explained the changes seen. Where observed, shifts from landfill towards incineration constitute an approach whereby waste management moves up the waste hierarchy as opposed to an attempt to reach the most preferred option(s); in terms of resource efficiency, this practice is sub-optimal. The requirement to supply incinerators with a feedstock over their lifespan reduces the benefits of developing of recycling and waste reduction, although access to incineration infrastructure permits short-term and marked decreases in the proportion of LACW landfilled. We conclude that there is a need for clearer national strategy and co-ordination to inform and guide policy, practice, planning and investment in infrastructure such that waste management can be better aligned with the principles of the circular economy and resource efficiency. If the ongoing stand-off between national political figures and the waste sector continues, England's waste policy remains destined for indecision. Copyright © 2015 Elsevier Ltd. All rights reserved.

Life cycle assessment of ship-generated waste management of Luka Koper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuin, Stefano, E-mail: sz.cvr@vegapark.ve.i; Belac, Elvis; Marzi, Boris

2009-12-15

Sea ports and the related maritime activities (e.g. shipping, shipbuilding, etc.) are one of the main driver of Europe's growth, jobs, competitiveness and prosperity. The continuously growth of shipping sectors has however introduced some environmental concerns, particularly with respect to ship-generated waste management. The port of Koper, one of the major ports on the northern Adriatic Coast, is the focus of this study. In this paper, a life cycle assessment was performed to identify and quantify the environmental impacts caused by the ship-generated waste management of port of Koper. Carcinogens substance (e.g. dioxins) and inorganic emissions, especially heavy metals, resultedmore » to be the most critical environmental issues, while the fossil fuels consumption is reduced by recovery of ship-generated oils. Moreover, the final treatment of ship waste was found to be critical phase of the management, and the landfill have a significant contribute to the overall environmental load. These results can be useful in the identification of the best practices and in the implementation of waste management plans in ports.« less

Implementation of spatial smart waste management system in malaysia

NASA Astrophysics Data System (ADS)

Omar, M. F.; Termizi, A. A. A.; Zainal, D.; Wahap, N. A.; Ismail, N. M.; Ahmad, N.

2016-06-01

One of the challenges to innovate and create an IoT -enabled solution is in monitoring and management of the environment. Waste collection utilizing the Internet of Things (IoT) with the technology of smart wireless sensors will able to gather fill-level data from waste containers hence providing a waste monitoring solution that brings up savings in waste collection costs. One of the challenges to the local authority is how to monitor the works of contractor effective and efficiently in waste management. This paper will propose to the local authority the implementation of smart waste management in Malaysia to improve the city management and to provide better services to the public towards smart city applications.

Development of tools for evaluating integrated municipal waste management using life-cycle management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thorneloe, S.; Weitz, K.; Nishtala, S.

1998-08-01

Municipal solid waste (MSW) management increasingly is based on integrated systems. The US initiated research in 1994 through funding by the US Environmental Protection Agency and the US Department of Energy to develop (1) a decision support tool; (2) a database; and (3) case studies. This paper provides an overview of the research that is in process.

Impact of an educational program on knowledge and practice of health care staff toward pharmaceutical waste management in Gaza, Palestine.

PubMed

Tabash, Mohammed I; Hussein, Rim A; Mahmoud, Aleya H; El-Borgy, Mohamed D; Abu-Hamad, Bassam A

2016-04-01

In health care facilities, pharmaceutical waste is generally discharged down the drain or sent to landfill. Poor knowledge about their potential downstream impacts may be a primary factor for improper disposal behavior. The objective of this study was to determine the impact of an intervention program on knowledge and practice of health care staff regarding pharmaceutical waste management. The study was designed as a pre/posttest intervention study. Total sample size was 530 in the pre-intervention phase, and then a subsample of 69 individuals was selected for the intervention and the post-intervention phases. Paired-sample t test was used to assess the difference between pretest and follow-up test results. A statistically significant improvement in knowledge and practice was achieved (P<0.001). Poor knowledge and poor practice levels (scores<50%) were found to improve to satisfactory levels (scores≥75%). Therefore, educational programs could be considered as an effective tool for changing health care staff practice in pharmaceutical waste management. In health care facilities, pharmaceutical waste is generally discharged down the drain or sent to landfill. A lack of knowledge about the potential impacts of this type of waste may be a leading factor in improper disposal behavior. Following an educational program, statistically significant improvement in knowledge and practice of health care staff as regards to pharmaceutical waste management (PWM) was achieved. It is thus recommended that authorities implement training-of-trainers (TOT) programs to educate health care staff on PWM and organize refreshment workshops regularly.

Magnitude of anthropogenic phosphorus storage in the agricultural production and the waste management systems at the regional and country scales.

PubMed

Chowdhury, Rubel Biswas; Chakraborty, Priyanka

2016-08-01

Based on a systematic review of 17 recent substance flow analyses of phosphorus (P) at the regional and country scales, this study presents an assessment of the magnitude of anthropogenic P storage in the agricultural production and the waste management systems to identify the potential for minimizing unnecessary P storage to reduce the input of P as mineral fertilizer and the loss of P. The assessment indicates that in case of all (6) P flow analyses at the regional scale, the combined mass of annual P storage in the agricultural production and the waste management systems is greater than 50 % of the mass of annual P inflow as mineral fertilizer in the agricultural production system, while this is close to or more than 100 % in case of half of these analyses. At the country scale, in case of the majority (7 out of 11) of analyses, the combined mass of annual P storage in the agricultural production and the waste management systems has been found to be roughly equivalent or greater than 100 % of the mass of annual P inflow as mineral fertilizer in the agricultural production system, while it ranged from 30 to 60 % in the remaining analyses. A simple scenario analysis has revealed that the annual storage of P in this manner over 100 years could result in the accumulation of a massive amount of P in the agricultural production and the waste management systems at both the regional and country scales. This study suggests that sustainable P management initiatives at the regional and country scales should put more emphasis on minimizing unwanted P storage in the agricultural production and the waste management systems.

Developing Tribal Integrated Waste Management Plans

EPA Pesticide Factsheets

An IWMP outlines how the tribe will reduce, manage, and dispose of its waste. It identifies existing waste systems, assesses needs, and sets forth the ways to design, implement, and monitor a more effective and sustainable waste management program.

Theoretical Framework for Plastic Waste Management in Ghana through Extended Producer Responsibility: Case of Sachet Water Waste.

PubMed

Quartey, Ebo Tawiah; Tosefa, Hero; Danquah, Kwasi Asare Baffour; Obrsalova, Ilona

2015-08-20

Currently, use and disposal of plastic by consumers through waste management activities in Ghana not only creates environmental problems, but also reinforces the notion of a wasteful society. The magnitude of this problem has led to increasing pressure from the public for efficient and practical measures to solve the waste problem. This paper analyses the impact of plastic use and disposal in Ghana. It emphasizes the need for commitment to proper management of the impacts of plastic waste and effective environmental management in the country. Sustainable Solid Waste Management (SSWM) is a critical problem for developing countries with regards to climate change and greenhouse gas emission, and also the general wellbeing of the populace. Key themes of this paper are producer responsibility and management of products at end of life. The paper proposes two theatrical recovery models that can be used to address the issue of sachet waste in Ghana.