Coatings to reduce wood preservative leaching.

PubMed

Nejad, Mojgan; Cooper, Paul

2010-08-15

The efficiency of semitransparent penetrating stains to reduce leaching of wood preservative components was evaluated. Five commercial wood deck finishes were applied to untreated and chromated copper arsenate (CCA), alkaline copper quat (ACQ), and copper azole (CA) treated wood, and leachates were collected and analyzed during 3 years of natural weathering exposure in Toronto, Canada. All stains evaluated effectively reduced the cumulative leaching of all inorganic preservative components by about 60% on average. Although most coatings showed significant film degradation starting around 12 months, the reduced leaching persisted even after 3 years. This suggests that temporary protection of wood with a coating during the early stages of use resulted in long-term reduction in preservative leaching potential. A two-week screening leaching test was able to predict the long-term leaching performance of different coatings reasonably well. Cured coating glass transition temperature (Tg) and liquid coating viscosity were the most important variables affecting a leaching prediction model. To effectively reduce leaching of preservative components from treated wood, coatings should have Tg low enough to withstand stresses caused by freezing in winter and have adequate viscosity to form a barrier film layer on the wood surface.

Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

Treesearch

Samuel L. Zelinka

2013-01-01

This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

Water repellents and water-repellent preservatives for wood

Treesearch

R. Sam Williams; William C. Feist

1999-01-01

Water repellents and water-repellent preservatives increase the durability of wood by enabling the wood to repel liquid water. This report focuses on water-repellent finishes for wood exposed outdoors above ground. The report includes a discussion of the effects of outdoor exposure on wood, the characteristics of water repellent and water-repellent preservative...

SYNERGISTIC WOOD PRESERVATIVES FOR REPLACEMENT OF CCA

EPA Science Inventory

The objective of this project was to evaluate the potential synergistic combinations of environmentally-safe biocides as wood preservatives. These wood preservatives could be potential replacements for the heavy-metal based CCA.

Didecyldimethylammonium chloride [DDAC] was...

Guide for Use of Wood Preservatives in Historic Structures

Treesearch

Stan Lebow; Ronald W. Anthony

2012-01-01

This document provides guidance on wood preservation options in the context of historic preservation. Preserving wooden building materials is critical to historic preservation practitioners. Biodeterioration can be minimized through design, construction practices, maintenance, and, if necessary, by use of wood preservatives. Moisture is the primary cause of...

Flavanoid biocides: Wood preservatives based on condensed tannins

Treesearch

Peter Laks; Peggy A. McKaig; Richard W. Hemingway

1988-01-01

The condensed tannins are natural wood preservatives found in high concentrations in the bark and wood of some tree species. Condensed tannin-containing bark extracts from loblolly pine (Pinus taeda) were evaluated as wood preservatives using standard methods. Bark extracts by themselves did not cause any reduction in weight loss of pressure-treated...

The application of near infrared (NIR) spectroscopy to inorganic preservative-treated wood

Treesearch

Chi-Leung So; Stan T. Lebow; Leslie H. Groom; Timothy G. Rials

2004-01-01

There is a growing need to find a rapid, inexpensive, and reliable method to distinguish between treated and untreated waste wood. This paper evaluates the ability of near infrared (NIR) spectroscopy with multivariate analysis (MVA) to distinguish preservative types and retentions. It is demonstrated that principal component analysis (PCA) can differentiate lumber...

Interaction of copper wood preservatives and adhesives

Treesearch

Charles R. Frihart

2003-01-01

Compared to other substrates, wood is generally easy to bond. However, adhesion is diminished when the wood surface is covered by chemicals, whether natural oils and resins or added chemicals. Among the chemicals added to wood are fire retardants and wood preservatives. Chromated copper arsenate (CCA) has been widely used to protect wood against rot and termites, but...

Gliomas and exposure to wood preservatives.

PubMed Central

Cordier, S; Poisson, M; Gerin, M; Varin, J; Conso, F; Hemon, D

1988-01-01

A case-referent study was undertaken to look for occupational risk factors among patients with glioma treated in a neurological hospital in Paris between 1975 and 1984. In the study group were 125 men with gliomas (aged less than or equal to 65) and 238 patients (also less than or equal to 65) admitted for non-neoplastic, non-malformative vascular diseases in the same department during the same period constituting the reference group. All diagnoses were confirmed by tomodensitometry. Information on occupational history was obtained from a postal questionnaire and from medical records. Comparison of cases and referents showed a significant excess risk among teachers (OR = 4.1) and a raised risk among wood workers (OR = 1.6). Four of nine cases of glioma who had been employed as wood workers reported that a colleague had suffered from glioma (those reports were confirmed by hospital records). None were reported among 11 referent wood workers. Using a complementary questionnaire on wood work, exposure assessment to wood preservatives and solvents showed that frequent exposure to organochlorine wood preservatives and to organic solvents occurred more often among cases than referent wood workers (p less than 0.10). PMID:3196664

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

PubMed Central

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55–65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0–25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

PubMed

Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T

Bioremediation of treated wood with fungi

Treesearch

Barbara L. Illman; Vina W. Yang

2006-01-01

The authors have developed technologies for fungal bioremediation of waste wood treated with oilborne or metal-based preservatives. The technologies are based on specially formulated inoculum of wood-decay fungi, obtained through strain selection to obtain preservative-tolerant fungi. This waste management approach provides a product with reduced wood volume and the...

Direct current testing to measure corrosiveness of wood preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; Donald S. Stone; James T. Gilbertson

2007-01-01

A qualitative test that mimics the corrosion behaviour of metals in contact with treated wood without using wood specimens would be of great value in rapidly evaluating the corrosiveness of new wood preservatives. The objective of this study was to determine whether the linear polarisation resistance of metals immersed in a solution of preservative chemicals is related...

40 CFR 429.90 - Applicability; description of the wood preserving-Boulton subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... CATEGORY Wood Preserving-Boulton Subcategory § 429.90 Applicability; description of the wood preserving... introduction of process wastewater pollutants into a publicly owned treatment works from wood preserving...

40 CFR 429.90 - Applicability; description of the wood preserving-Boulton subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the wood... CATEGORY Wood Preserving-Boulton Subcategory § 429.90 Applicability; description of the wood preserving... introduction of process wastewater pollutants into a publicly owned treatment works from wood preserving...

40 CFR 429.90 - Applicability; description of the wood preserving-Boulton subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the wood... CATEGORY Wood Preserving-Boulton Subcategory § 429.90 Applicability; description of the wood preserving... introduction of process wastewater pollutants into a publicly owned treatment works from wood preserving...

Methods for Mitigating the Environmental Risks Associated with Wood Preservatives

Treesearch

Dennis Hayward; Stan T. Lebow; Kenneth M. Brooks

2011-01-01

As noted in earlier chapters, the treatment of wood is both art and science. Wood is a variable material; treatment results tend to vary with the preservative and wood species and even within boards of the same species. This means that treated wood often contains a range of preservative retentions. Some pieces will have less than the desired retention, while others may...

PRODUCTS OF INCOMPLETE COMBUSTION FROM DIRECT BURNING OF PENTACHLOROPHENOL-TREATED WOOD WASTES

EPA Science Inventory

The report gives results of a study to identify potential air pollution problems from the combustion of waste wood treated with pentachlorophenol preservative for energy production in a boiler. The study emphasized the characterization of the products of incomplete combustion (PI...

PRESERVATIVE LEACHING FROM WEATHERED CCA-TREATED WOOD

EPA Science Inventory

Disposal of discarded CCA-treated wood in landfills raises concerns with respect to leaching of preservative compounds. When unweathered CCA-treated wood is leached using the toxicity characteristic leaching procedure (TCLP), arsenic concentrations exceed the toxicity characteris...

Preservative-treated wood and alternative products in the Forest Service

Treesearch

James (Scott) Groenier; Stan Lebow

2006-01-01

When treated wood is used in field settings, the possibility of environmental contamination raises concerns. There is increasing pressure to be environmentally friendly and to reduce, restrict, or eliminate the use of wood preservatives because of the concern that toxic constituents may leach from the treated wood. This report will provide an overview of preservative...

A new shock wave assisted wood preservative injection system

NASA Astrophysics Data System (ADS)

Rao, K. S.; Ravikumar, G.; Lai, Ram; Jagadeesh, G.

Preservative treatment of many tropical hard woods and bamboo pose severe problem. A number of wood preservatives (chemical formulations toxic to wood decay/ destroying organisms like fungi, wood destroying termites, marine borers etc.) and wood impregnating techniques are currently in use for improving bio resistance of timber and bamboo and thereby enhancing service life for different end uses. How ever, some species of tropical hardwoods and many species of bamboo are difficult to treat, posing technical problems. In this paper we report preliminary results of treatment of bamboo with a novel Shockwave assisted injection treatment. Samples (30×2.5×1.00 cm) of an Indian species of bamboo Dendrocalamus strictus prepared from defect free culms of dry bamboo are placed in the driven section of a vertical shock tube filled with the 4Coppepr-Chrome-Arsenic(CCA) preservative solution.The bamboo samples are subjected to repeated shock wave loading (3 shots) with typical over pressures of 30 bar. The results from the study indicate excellent penetration and retention of CCA preservative in bamboo samples. The method itself is much faster compared to the conventional methods like pressure treatment or hot and cold process.

40 CFR 429.80 - Applicability; description of the wood preserving-steam subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the wood... Wood Preserving Steam Subcategory § 429.80 Applicability; description of the wood preserving—steam... process wastewater pollutants into publicly owned treatment works from wood preserving processes that use...

40 CFR 429.80 - Applicability; description of the wood preserving-steam subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the wood... Wood Preserving Steam Subcategory § 429.80 Applicability; description of the wood preserving—steam... process wastewater pollutants into publicly owned treatment works from wood preserving processes that use...

40 CFR 429.80 - Applicability; description of the wood preserving-steam subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... Wood Preserving Steam Subcategory § 429.80 Applicability; description of the wood preserving—steam... process wastewater pollutants into publicly owned treatment works from wood preserving processes that use...

40 CFR 429.90 - Applicability; description of the wood preserving-Boulton subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... Wood Preserving-Boulton Subcategory § 429.90 Applicability; description of the wood preserving—Boulton... process wastewater pollutants into a publicly owned treatment works from wood preserving operations which...

40 CFR 429.90 - Applicability; description of the wood preserving-Boulton subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the wood... Wood Preserving-Boulton Subcategory § 429.90 Applicability; description of the wood preserving—Boulton... process wastewater pollutants into a publicly owned treatment works from wood preserving operations which...

BIOREMEDIATION FIELD INITIATIVE SITE PROFILE: ESCAMBIA WOOD PRESERVING SITE - BROOKHAVEN

EPA Science Inventory

The Escambia Wood Preserving Site—Brookhaven in Brookhaven, Mississippi, is a former wood preserving facility that used pentachlo- rophenol (PCP) and creosote to treat wooden poles. The site contains two pressure treatment cylinders, a wastewater treatment system, five bulk pr...

Corrosion avoidance with new wood preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2006-01-01

The increased use of alkaline copper quaternary (ACQ) and copper azole (CuAz) as wood preservatives for residential construction has led to concerns about the corrosion performance of fasteners. Information on the effects of these preservatives on the corrosion rate is limited, although Simpson Strong Tie has published a technical bulletin indicating that both ACQ and...

BIOREMEDIATION AT WOOD-PRESERVING SITES

EPA Science Inventory

The removal of organic compounds from ground water during bioremediation at wood-preserving sites is a function of the stoichiometric demand for electron acceptors (oxygen, nitrate, and sulfate) to metabolize the organic contaminants and the supply of the electron acceptors in th...

Waste wood as bioenergy feedstock. Climate change impacts and related emission uncertainties from waste wood based energy systems in the UK.

PubMed

Röder, Mirjam; Thornley, Patricia

2018-04-01

Considering the urgent need to shift to low carbon energy carriers, waste wood resources could provide an alternative energy feedstock and at the same time reduce emissions from landfill. This research examines the climate change impacts and related emission uncertainties of waste wood based energy. For this, different grades of waste wood and energy application have been investigated using lifecycle assessment. Sensitivity analysis has then been applied for supply chain processes and feedstock properties for the main emission contributing categories: transport, processing, pelletizing, urea resin fraction and related N 2 O formation. The results show, depending on the waste wood grade, the conversion option, scale and the related reference case, that emission reductions of up to 91% are possible for non-treated wood waste. Compared to this, energy from treated wood waste with low contamination can achieve up to 83% emission savings, similar to untreated waste wood pellets, but in some cases emissions from waste wood based energy can exceed the ones of the fossil fuel reference - in the worst case by 126%. Emission reductions from highly contaminated feedstocks are largest when replacing electricity from large-scale coal and landfill. The highest emission uncertainties are related to the wood's resin fraction and N 2 O formation during combustion and, pelletizing. Comparing wood processing with diesel and electricity powered equipment also generated high variations in the results, while emission variations related to transport are relatively small. Using treated waste wood as a bioenergy feedstock can be a valid option to reduce emissions from energy production but this is only realisable if coal and landfill gas are replaced. To achieve meaningful emission reduction in line with national and international climate change targets, pre-treatment of waste wood would be required to reduce components that form N 2 O during the energy conversion. Copyright © 2017

Methanol from wood waste : a technical and economic study

Treesearch

A. E. Hokanson; R. M. Rowell

1977-01-01

A methanol-from-wood waste facility having a capacity of 50 million gallons per year requires 1,500 ovendry tons (ODT) of wood waste per day. The yield of methanol from wood is about 38 percent, or about 100 gallons per ODT of wood. This yield is based on all process energy required coming from the wood waste. At a wood waste cost of $15/ODT, the selling price of...

Tolerance to wood preservatives by copper-tolerant wood-rot fungi native to south-central Chile.

PubMed

Guillén, Yudith; Navias, David; Machuca, Angela

2009-02-01

Understanding the effect of heavy metals and wood preservatives on the growth of wood-rot fungi native to a certain region may improve reliability in determining the effectiveness of antifungal products, particularly when dealing with new formulations. In this investigation, strains of copper-tolerant wood-rot fungi native to south-central Chile were evaluated against two preservatives: commercial chromated copper arsenate type C (CCA-C) and a new formulation with boron and silicon (BS). Thirteen native strains, mainly white-rot fungi, were selected for their high growth rates in solid medium containing 3 mM of copper. A short-term test was then carried out, consisting of adding cellulose disks impregnated with different concentrations of preservatives to solid culture media inoculated with selected copper tolerant strains. There was a great variability in interspecific and intraspecific responses to the presence of copper and preservatives in culture media. Among the native and commercial strains evaluated, the white-rot fungi Trametes versicolor 38 and mainly Ganoderma australe 100 were notable for their tolerance to all the CCA-C and BS concentrations. The brown-rot fungus Wolfiporia cocos, used as reference strain, showed a high tolerance to CCA-C, but not to BS preservative. T. versicolor 38 and G. australe 100 were selected for subsequent studies on preserved wood degradation.

TREATMENT TECHNOLOGY PERFORMANCE AND COST DATA FOR REMEDIATION OF WOOD PRESERVING SITES

EPA Science Inventory

Wood preserving has been an industry in North America for more than 100 years. During this time wood preserving facilities have utilized a variety of compounds, including pentachlorophenol (PCP), creosote, and certain metals to extend the useful life of wood products. Past operat...

Amplicon-Based Sequencing of Soil Fungi from Wood Preservative Test Sites

PubMed Central

Kirker, Grant T.; Bishell, Amy B.; Jusino, Michelle A.; Palmer, Jonathan M.; Hickey, William J.; Lindner, Daniel L.

2017-01-01

Soil samples were collected from field sites in two AWPA (American Wood Protection Association) wood decay hazard zones in North America. Two field plots at each site were exposed to differing preservative chemistries via in-ground installations of treated wood stakes for approximately 50 years. The purpose of this study is to characterize soil fungal species and to determine if long term exposure to various wood preservatives impacts soil fungal community composition. Soil fungal communities were compared using amplicon-based DNA sequencing of the internal transcribed spacer 1 (ITS1) region of the rDNA array. Data show that soil fungal community composition differs significantly between the two sites and that long-term exposure to different preservative chemistries is correlated with different species composition of soil fungi. However, chemical analyses using ICP-OES found levels of select residual preservative actives (copper, chromium and arsenic) to be similar to naturally occurring levels in unexposed areas. A list of indicator species was compiled for each treatment-site combination; functional guild analyses indicate that long-term exposure to wood preservatives may have both detrimental and stimulatory effects on soil fungal species composition. Fungi with demonstrated capacity to degrade industrial pollutants were found to be highly correlated with areas that experienced long-term exposure to preservative testing. PMID:29093702

Forest biomass and wood waste resources

Treesearch

K. Skog; P. Lebow; D. Dykstra; P. Miles; B.J. Stokes; R.D. Perlack; M. Buford; J. Barbour; D. McKeever

2011-01-01

This chapter provides estimates of forest biomass and wood waste quantities, as well as roadside costs (i.e., supply curves) for each county in the contiguous United States. Roadside price is the price a buyer pays for wood chips at a roadside in the forest, at a processing mill location in the case of mill residue, or at a landfill for urban wood wastes prior to any...

Online sorting of recovered wood waste by automated XRF-technology: part II. Sorting efficiencies.

PubMed

Hasan, A Rasem; Solo-Gabriele, Helena; Townsend, Timothy

2011-04-01

Sorting of waste wood is an important process practiced at recycling facilities in order to detect and divert contaminants from recycled wood products. Contaminants of concern include arsenic, chromium and copper found in chemically preserved wood. The objective of this research was to evaluate the sorting efficiencies of both treated and untreated parts of the wood waste stream, and metal (As, Cr and Cu) mass recoveries by the use of automated X-ray fluorescence (XRF) systems. A full-scale system was used for experimentation. This unit consisted of an XRF-detection chamber mounted on the top of a conveyor and a pneumatic slide-way diverter which sorted wood into presumed treated and presumed untreated piles. A randomized block design was used to evaluate the operational conveyance parameters of the system, including wood feed rate and conveyor belt speed. Results indicated that online sorting efficiencies of waste wood by XRF technology were high based on number and weight of pieces (70-87% and 75-92% for treated wood and 66-97% and 68-96% for untreated wood, respectively). These sorting efficiencies achieved mass recovery for metals of 81-99% for As, 75-95% for Cu and 82-99% of Cr. The incorrect sorting of wood was attributed almost equally to deficiencies in the detection and conveyance/diversion systems. Even with its deficiencies, the system was capable of producing a recyclable portion that met residential soil quality levels established for Florida, for an infeed that contained 5% of treated wood. Copyright © 2010 Elsevier Ltd. All rights reserved.

Efficacy of copper borax preservative against wood decay

Treesearch

William Abbott; Bessie Woodward; Michael West

2001-01-01

In this study, a wood preservative containing active ingredients of 43.5% borax and 3.1% copper hydroxide was evaluated in soil-block tests in accordance with AWPA E10. Results suggested thatthe copper hydroxide was not contributing to fungal toxicity at preservative threshold levels. Thresholds determined for this preservative were very close to those previously...

Tolerance of Serpula lacrymans to copper-based wood preservatives

Treesearch

Anne Christine Steenkjaer Hastrup; Frederick Green; Carol A. Clausen; Bo Jensen

2005-01-01

Serpula lacrymans, the dry rot fungus, is considered the most economically important wood decay fungus in certain temperate regions of the world, namely northern Europe, Japan, and Australia. Previously, copper-based wood preservatives were commonly used for pressure treatment of wood for building construction, but some decay fungi are known to be copper tolerant. In...

TREATABILITY STUDIES FOR WOOD PRESERVING SITES

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA), National Risk Management Research Laboratory (NRMRL), Site Management Support Branch, conducted a comprehensive treatability project for wood preserving sites in 1995 and 1996. This is a compilation report on the treatability studi...

Successful approaches to recycling urban wood waste

Treesearch

Solid Waste Association of North America

2002-01-01

This report presents eight case studies of successful urban wood waste recycling projects and businesses. These studies document the success of recovered products such as lumber and lumber products, mulch, boiler fuel, and alternative cover for landfills. Overall, wood waste accounts for about 17% of the total waste received at municipal solid waste landfills in the...

An investigation into the potential of ionic silver as a wood preservative

Treesearch

Benjamin Dorau; Rachel Arango; Frederick Green

2004-01-01

On December 3 1, 2003, the wood preservation industry, in conjunction with the Environmental Protection Agency, voluntarily phased out the use of chromated copper arsenate (CCA)-treated lumber for residential applications. This ended over 25 years of CCA as the predominant wood preservative in the United States. The first generation of replacement preservatives,...

Marine exposure of preservative-treated small wood panels

Treesearch

B. R. Johnson; D. I. Gutzmer

1984-01-01

Small wood panels treated with many different chemicals have been exposed to limnorian and teredine marine borers in the sea at Key West, Florida. These preservatives and treatments include creosotes with and without modification, waterborne salts, salt-creosote dual treatments, chemical modifications of wood, and modified polymers. In spite of the accelerated nature...

New Developments in Wood-Destroying Organisms from the International Research Group on Wood Preservation \\t

Treesearch

Elmer L. Schmidt

1991-01-01

New developments in wood-destroying organisms and in wood protection from the 20th annual meeting (May 1989 at Lappeenranta, Finland) of the International Research Group on Wood Preservation (IRG) are highlighted in the areas of biological control of fungi, dry rot, decay mechanisms and product problems, new techniques, insect problems and control, and developments in...

Furniture wood wastes: Experimental property characterisation and burning tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna

2009-10-15

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675more » to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.« less

The use of urban wood waste as an energy resource

NASA Astrophysics Data System (ADS)

Khudyakova, G. I.; Danilova, D. A.; Khasanov, R. R.

2017-06-01

The capabilities use of wood waste in the Ekaterinburg city, generated during the felling of trees and sanitation in the care of green plantations in the streets, parks, squares, forest parks was investigated in this study. In the cities at the moment, all the wood, that is removed from city streets turns into waste completely. Wood waste is brought to the landfill of solid household waste, and moreover sorting and evaluation of the quantitative composition of wood waste is not carried out. Several technical solutions that are used in different countries have been proposed for the energy use of wood waste: heat and electrical energy generation, liquid and solid biofuel production. An estimation of the energy potential of the city wood waste was made, for total and for produced heat and electrical energy based on modern engineering developments. According to our estimates total energy potential of wood waste in the city measure up more 340 thousand GJ per year.

Pretreatment Characteristics of Waste Oak Wood by Ammonia Percolation

NASA Astrophysics Data System (ADS)

Kim, Jun-Seok; Kim, Hyunjoon; Lee, Jin-Suk; Lee, Joon-Pyo; Park, Soon-Chul

A log of waste oak wood collected from a Korean mushroom farm has been tested for ammonia percolation pretreatment. The waste log has different physical characteristics from that of virgin oak wood. The density of the waste wood was 30% lower than that of virgin oak wood. However, there is little difference in the chemical compositions between the woods. Due to the difference in physical characteristics, the optimal pretreatment conditions were also quite different. While for waste oak the optimum temperature was determined to be 130°C, for virgin oak wood the optimum pretreatment was only achieved at 170°C. Presoaking for 12 h with ammonia solution before pretreatment was helpful to increase the delignification efficiency.

Kraft pulping of industrial wood waste

Treesearch

Aziz Ahmed; Masood Akhtar; Gary C. Myers; Gary M. Scott

1998-01-01

Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

Bioremediation and degradation of CCA-treated wood waste.

Treesearch

Barbara L Illman; Vina W. Yang

2004-01-01

Bioprocessing CCA wood waste is an efficient and economical alternative to depositing the waste in landfills, especially if landfill restrictions on CCA waste are imposed nation wide. We have developed bioremediation and degradation technologies for microbial processing of CCA waste. The technologies are based on specially formulated inoculum of wood decay fungi,...

Characterization and potential recycling of home building wood waste

Treesearch

Philip A. Araman; D.P. Hindman; M.F. Winn

2010-01-01

Construction waste represents a significant portion of landfill waste, estimated as 17% of the total waste stream. Wood construction waste of a 2000 square foot single family home we found to be 1500-3700 lbs of solid-sawn wood, and 1000-1800 lbs of engineered wood products (EWP). Much of the solid-sawn lumber and EWPs could be recycled into several products. Through a...

Serpula lacrymans, the dry rot fungus and tolerance towards copper-based wood preservatives

Treesearch

Anne Christine Steenkjaer Hastrup; Frederick Green; Carol Clausen; Bo Jensen

2005-01-01

Serpula lacrymans (Wulfen : Fries) Schröter, the dry rot fungus, is considered the most economically important wood decay fungus in temperate regions of the world i.e. northern Europe, Japan and Australia. Previously copper based wood preservatives were the most commonly used preservatives for pressure treatment of wood for building constructions. Because of a...

Evaluation of nonpressure wood preservatives for military applications

Treesearch

Stan T. Lebow; Samuel L. Zelinka; Rachel A. Arango; Bessie M. Woodward; Patricia K. Lebow; Katie M. Ohno; Nathaniel P. Chotlos

2017-01-01

Zinc naphthenate (ZnN) has been widely used for dip treatment of Department of Defense wood packaging materials but is no longer available. Research was conducted to evaluate the preservative efficacy and corrosiveness of U.S. Environmental Protection Agency (EPA) registered alternatives to ZnN. Efficacy of “green” preservatives (defined here as not containing...

USEPA SHEDS MODEL: METHODOLOGY FOR EXPOSURE ASSESSMENT FOR WOOD PRESERVATIVES

EPA Science Inventory

A physically-based, Monte Carlo probabilistic model (SHEDS-Wood: Stochastic Human Exposure and Dose Simulation model for wood preservatives) has been applied to assess the exposure and dose of children to arsenic (As) and chromium (Cr) from contact with chromated copper arsenat...

Guide for minimizing the effect of preservative-treated wood on sensitive environments

Treesearch

Stan T. Lebow; Michael Tippie

2001-01-01

Preservative-treated wood is often used for construction of highway and foot bridges, wetland boardwalks, and other structures in or over water or sensitive environments. In these applications it is important that release of preservative from the wood into the environment is minimized. This publication addresses this concern by describing the various types of pressure-...

Wood preservatives : choosing the right one

Treesearch

Matt Humphries; Stan Lebow; David Moses

2009-01-01

If you are having trouble choosing the right wood preservative system for your application, you are not alone. Dozens of products are available, some older types have gone out of use, others may be completely inappropriate for your application. As designers, specifiers and builders, you need to understand key information to be able to navigate through all of these...

40 CFR 429.70 - Applicability; description of the wood preserving-water borne or nonpressure subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the wood... PROCESSING POINT SOURCE CATEGORY Wood Preserving-Water Borne or Nonpressure Subcategory § 429.70 Applicability; description of the wood preserving-water borne or nonpressure subcategory. This subpart applies...

40 CFR 429.70 - Applicability; description of the wood preserving-water borne or nonpressure subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... PROCESSING POINT SOURCE CATEGORY Wood Preserving-Water Borne or Nonpressure Subcategory § 429.70 Applicability; description of the wood preserving-water borne or nonpressure subcategory. This subpart applies...

40 CFR 429.70 - Applicability; description of the wood preserving-water borne or nonpressure subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the wood... PROCESSING POINT SOURCE CATEGORY Wood Preserving-Water Borne or Nonpressure Subcategory § 429.70 Applicability; description of the wood preserving-water borne or nonpressure subcategory. This subpart applies...

40 CFR 429.70 - Applicability; description of the wood preserving-water borne or nonpressure subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the wood... SOURCE CATEGORY Wood Preserving-Water Borne or Nonpressure Subcategory § 429.70 Applicability; description of the wood preserving-water borne or nonpressure subcategory. This subpart applies to discharges...

40 CFR 429.70 - Applicability; description of the wood preserving-water borne or nonpressure subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... SOURCE CATEGORY Wood Preserving-Water Borne or Nonpressure Subcategory § 429.70 Applicability; description of the wood preserving-water borne or nonpressure subcategory. This subpart applies to discharges...

40 CFR 429.80 - Applicability; description of the wood preserving-steam subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Preserving Steam Subcategory § 429.80 Applicability; description of the wood preserving—steam subcategory...

40 CFR 429.80 - Applicability; description of the wood preserving-steam subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the wood... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Preserving Steam Subcategory § 429.80 Applicability; description of the wood preserving—steam subcategory...

Evaluation of wood species and preservatives for WisDOT sign posts.

DOT National Transportation Integrated Search

2013-10-01

The Wisconsin Department of Transportation (WisDOT) uses preservative-treated wood posts for much of the signage along state highways because wood is relatively inexpensive, easy to install, and has the necessary strength properties to tolerate typic...

Amplicon-Based Sequencing of Soil Fungi from Wood Preservative Test Sites

Treesearch

Grant T. Kirker; Amy B. Bishell; Michelle A. Jusino; Jonathan M. Palmer; William J. Hickey; Daniel L. Lindner

2017-01-01

Soil samples were collected from field sites in two AWPA (American Wood Protection Association) wood decay hazard zones in North America. Two field plots at each site were exposed to differing preservative chemistries via in-ground installations of treated wood stakes for approximately 50 years. The purpose of this study is to characterize soil fungal species and to...

Technical Note: Comparison of accelerated methods for evaluating leaching from preservative-treated wood

Treesearch

Stan T. Lebow; Patricia K. Lebow; Kolby C. Hirth

2017-01-01

Current standardized methods are not well-suited for estimating in-service preservative leaching from treated wood products. This study compared several alternative leaching methods to a commonly used standard method, and to leaching under natural exposure conditions. Small blocks or lumber specimens were pressure treated with a wood preservative containing borax and...

Bioremediation of treated wood with bacteria

Treesearch

Carol A. Clausen

2006-01-01

This chapter reviews prior research in the field of bacterial bioremediation for wood treated with oilborne and inorganic preservatives. Current state of the art is summarized along with potential benefits and pitfalls of a pilot-scale bioremediation process for CCA-treated waste wood.

Mineral preservatives in the wood of Stradivari and Guarneri.

PubMed

Nagyvary, Joseph; Guillemette, Renald N; Spiegelman, Clifford H

2009-01-01

Following the futile efforts of generations to reach the high standard of excellence achieved by the luthiers in Cremona, Italy, by variations of design and plate tuning, current interest is being focused on differences in material properties. The long-standing question whether the wood of Stradivari and Guarneri were treated with wood preservative materials could be answered only by the examination of wood specimens from the precious antique instruments. In a recent communication (Nature, 2006), we reported about the degradation of the wood polymers in instruments of Stradivari and Guarneri, which could be explained only by chemical manipulations, possibly by preservatives. The aim of the current work was to identify the minerals from the small samples of the maple wood which were available to us from the antique instruments. The ashes of wood from one violin and one cello by Stradivari, two violins by Guarneri, one viola by H. Jay, one violin by Gand-Bernardel were analyzed and compared with a variety of commercial tone woods. The methods of analysis were the following: back-scattered electron imaging, X-ray fluorescence maps for individual elements, wave-length dispersive spectroscopy, energy dispersive X-ray spectroscopy and quantitative microprobe analysis. All four Cremonese instruments showed the unmistakable signs of chemical treatments in the form of chemicals which are not present in natural woods, such as BaSO4, CaF2, borate, and ZrSiO4. In addition to these, there were also changes in the common wood minerals. Statistical evaluation of 12 minerals by discriminant analysis revealed: a. a difference among all four Cremona instruments, b. the difference of the Cremonese instruments from the French and English antiques, and c. only the Cremonese instruments differed from all commercial woods. These findings may provide the answer why all attempts to recreate the Stradivarius from natural wood have failed. There are many obvious implications with regard to

CONTAMINANTS AND REMEDIAL OPTIONS AT WOOD PRESERVING SITES

EPA Science Inventory

This document provides information that facilitates characterization of the site and selection of treatment technologies at wood preserving sites, to meet the regulations’ acceptable cleanup levels. It does not provide risk-assessment information or policy guidance related to det...

Fast analysis of wood preservers using laser induced breakdown spectroscopy

NASA Astrophysics Data System (ADS)

Uhl, A.; Loebe, K.; Kreuchwig, L.

2001-06-01

Laser-induced breakdown spectroscopy (LIBS) is used for the investigation of wood preservers in timber and in furniture. Both experiments in laboratory and practical applications in recycling facilities and on a building site prove the new possibilities for the fast detection of harmful agents in wood. A commercial system was developed for mobile laser-plasma-analysis as well as for industrial use in sorting plants. The universal measuring principle in combination with an Echelle optics permits real simultaneous multi-element-analysis in the range of 200-780 nm with a resolution of a few picometers. It enables the user to detect main and trace elements in wood within a few seconds, nearly independent of the matrix, knowing that different kinds of wood show an equal elemental composition. Sample preparation is not required. The quantitative analysis of inorganic wood preservers (containing, e.g. Cu, Cr, B, As, Pb, Hg) has been performed exactly using carbon as reference element. It can be shown that the detection limits for heavy metals in wood are in the ppm-range. Additional information is given concerning the quantitative analysis. Statistical data, e.g. the standard deviation (S.D.), were determined and calibration curves were used for each particular element. A comparison between ICP-AES and LIBS is given using depth profile correction factors regarding the different penetration depths with respect to the different volumes in wood analyzed by both analytical methods.

Performance of copper-based wood preservatives in soil bed exposures

Treesearch

Stan T. Lebow; Thomas Nilsson; Jeffrey J. Morrell

Copper-based biocides are widely used to protect wood from biological attack in a variety of environments. Chromated copper arsenate (CCA) is the dominant copper-based preservative for wood protection (J. T. MICKLEWRIGHT, 1989). First developed in India in the 1930s, CCA contains a very effective combination of materials. Copper provides protection against most...

Exposure testing of fasteners in preservative treated wood : gravimetric corrosion rates and corrosion product analyses

Treesearch

Samuel L. Zelinka; Rebecca J. Sichel; Donald S. Stone

2010-01-01

Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27oC at 100% relative humidity for 1 year. The...

40 CFR 268.30 - Waste specific prohibitions-wood preserving wastes.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) SOLID WASTES (CONTINUED) LAND DISPOSAL RESTRICTIONS Prohibitions on Land Disposal § 268.30 Waste... prohibited from land disposal: the wastes specified in 40 CFR part 261 as EPA Hazardous Waste numbers F032, F034, and F035. (b) Effective May 12, 1999, the following wastes are prohibited from land disposal...

40 CFR 268.30 - Waste specific prohibitions-wood preserving wastes.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) SOLID WASTES (CONTINUED) LAND DISPOSAL RESTRICTIONS Prohibitions on Land Disposal § 268.30 Waste... prohibited from land disposal: the wastes specified in 40 CFR part 261 as EPA Hazardous Waste numbers F032, F034, and F035. (b) Effective May 12, 1999, the following wastes are prohibited from land disposal...

40 CFR 268.30 - Waste specific prohibitions-wood preserving wastes.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) SOLID WASTES (CONTINUED) LAND DISPOSAL RESTRICTIONS Prohibitions on Land Disposal § 268.30 Waste... prohibited from land disposal: the wastes specified in 40 CFR part 261 as EPA Hazardous Waste numbers F032, F034, and F035. (b) Effective May 12, 1999, the following wastes are prohibited from land disposal...

Waste-wood-derived fillers for plastics

Treesearch

Brent English; Craig M. Clemons; Nicole Stark; James P. Schneider

1996-01-01

Filled thermoplastic composites are stiffer, stronger, and more dimensionally stable than their unfilled counterparts. Such thermoplastics are usually provided to the end-user as a precompounded, pelletized feedstock. Typical reinforcing fillers are inorganic materials like talc or fiberglass, but materials derived from waste wood, such as wood flour and recycled paper...

A Tool for Estimating Variability in Wood Preservative Treatment Retention

Treesearch

Patricia K. Lebow; Adam M. Taylor; Timothy M. Young

2015-01-01

Composite sampling is standard practice for evaluation of preservative retention levels in preservative-treated wood. Current protocols provide an average retention value but no estimate of uncertainty. Here we describe a statistical method for calculating uncertainty estimates using the standard sampling regime with minimal additional chemical analysis. This tool can...

INDEPENDENT POWER PLANT USING WOOD WASTE

EPA Science Inventory

A 1 MWe power plant using waste wood is to be installed at a U.S. Marine Corps base, which will supply all the wood for the plant from a landfill site. The core energy conversion technology is a down-draft gasifier supplying approximately 150 Btu/scf gas to both spark ignition an...

In Vitro Pulmonary Toxicity Assessment of Nano-Enabled Outdoor Wood Preservatives

EPA Science Inventory

Nanoscale CuCO3 (1 - 400 nm) and CeO2 (5 - 7 nm) particles are employed as a preservative and UV coating for outdoor wood, respectively. CuCO3 and CeO2 treated outdoor wood provide a product and application with a risk of dermal and/or inhalation exposures to a mixture of nanomat...

TREATMENT TECHNOLOGY FOR REMEDIATION OF WOOD PRESERVING SITES: OVERVIEW

EPA Science Inventory

This is the first in a series of five articles describing the applicability, performance and cost of technologies for the remediation of contaminated soil and water at wood preserving sites. Site-specific treatability studies conducted under the supervision of the USEPA NRMRL fro...

Evaluation of wood species and preservatives for Wisconsin transportation sign posts : [research brief].

DOT National Transportation Integrated Search

2013-12-01

The Wisconsin Department of Transportation (WisDOT) administers approximately 11,800 miles of state highways. It uses preservative-treated wood posts for much of the signage along these highways because wood is relatively inexpensive, easy to install...

Wolfiporia cocos : a potential agent for composting of bioprocessing Douglas-fir wood treated with copper-based preservatives

Treesearch

Rodney. De Groot; Bessie. Woodward

1998-01-01

In laboratory experiments, Douglas-fir wood blocks that were treated with copper- based wood preservatives were challenged with two wood decay fungi known to be tolerant of copper. Factors influencing the amount of decay, as determined by loss of weight in the test blocks, were preservative, then fungus. Within those combinations, the relative importance of...

Micronized copper wood preservatives: an efficiency and potential health risk assessment for copper-based nanoparticles.

PubMed

Civardi, Chiara; Schwarze, Francis W M R; Wick, Peter

2015-05-01

Copper (Cu) is an essential biocide for wood protection, but fails to protect wood against Cu-tolerant wood-destroying fungi. Recently Cu particles (size range: 1 nm-25 μm) were introduced to the wood preservation market. The new generation of preservatives with Cu-based nanoparticles (Cu-based NPs) is reputedly more efficient against wood-destroying fungi than conventional formulations. Therefore, it has the potential to become one of the largest end uses for wood products worldwide. However, during decomposition of treated wood Cu-based NPs and/or their derivate may accumulate in the mycelium of Cu-tolerant fungi and end up in their spores that are dispersed into the environment. Inhaled Cu-loaded spores can cause harm and could become a potential risk for human health. We collected evidence and discuss the implications of the release of Cu-based NPs by wood-destroying fungi and highlight the exposure pathways and subsequent magnitude of health impact. Copyright © 2015 Elsevier Ltd. All rights reserved.

Movement and fate of creosote waste in ground water, Pensacola, Florida; U.S. Geological Survey toxic waste-ground-water contamination program

USGS Publications Warehouse

Mattraw, Harold C.; Franks, Bernard J.

1986-01-01

Ground- and surface-water contamination by pesticides used in the wood-preserving industry is widespread in the United States. Pine poles were treated with wood preservatives from 1902 to 1981 at a creosote works near Pensacola, Florida. Diesel fuel, creosote, and pentachlorophenol were discharged to two unlined impoundments that had a direct hydraulic connection to the sand-and-gravel aquifer. Evidence of wood-preserving waste contamination appears to be confined to the upper 30 meters of the aquifer. The waste plume extends downgradient approximately 300 meters south toward Pensacola Bay. In 1983, the creosote works site was selected by the U.S. Geological Survey's Office of Hazardous Waste Hydrology as a national research demonstration area to apply the latest techniques for characterizing hazardous waste problems. The multidisciplinary research effort is aimed at studying processes that affect the occurrence, transport, transformations, and fate of the toxic contaminants associated with wood preservatives in the environment. Clusters of two to five wells were constructed at different depths at nine sites to define the depth of contamination. Research studies are investigating sorption, dispersion, dilution, chemical reactions, bacterially mediated transformations, quality assurance, plume hydrodynamics, and the ultimate fate of these complex organic wastes.

Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

Treesearch

Ronald W. Anthony; Stan T. Lebow

2015-01-01

Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

Life cycle assessment of wood wastes: A case study of ephemeral architecture.

PubMed

Rivela, Beatriz; Moreira, María Teresa; Muñoz, Iván; Rieradevall, Joan; Feijoo, Gumersindo

2006-03-15

One of the most commonly used elements in ephemeral architecture is a particleboard panel. These types of wood products are produced from wood wastes and they are used in temporary constructions such as trade fairs. Once the event is over, they are usually disposed into landfills. This paper intends to assess the environmental effects related to the use of these wood wastes in the end-of-life stage. The Life Cycle Assessment (LCA) of two scenarios was performed, considering the recycling of wood waste for particleboard manufacture and energy generation from non-renewable resources (Scenario 1) versus the production of energy from the combustion of wood waste and particleboard manufacture with conventional wooden resources (Scenario 2). A sensitive analysis was carried out taking into account the influence of the percentage of recycled material and the emissions data from wood combustion. According to Ecoindicator 99 methodology, Damage to Human Health and Ecosystem Quality are more significant in Scenario 2 whereas Scenario 1 presents the largest contribution to Damage to Resources. Between the two proposed alternatives, the recycling of wood waste for particleboard manufacture seems to be more favorable under an environmental perspective.

Application of hinokitiol potassium salt for wood preservative.

PubMed

Hu, Junyi; Shen, Yu; Pang, Song; Gao, Yun; Xiao, Guoyong; Li, Shujun; Xu, Yingqian

2013-12-01

The decay of wood and other cellulosic materials by fungi cause significant economic loss. The widely used chromated copper arsenate was prohibited for the environmental impact and safety of arsenic and chromium. It was found that natural product hinokitiol (HK) had fungicidal and insecticidal activities, and its toxicity was bearable for the environment. We described the practical synthesis of HK-K salt. According to the GB/T18261-2000 and LY/T1283-1998, wood preservative performance of HK-K salt was tested. The results showed that the best inhibitory concentration of HK-K salt was 50 mg/L, for which the prevention effectiveness on mold is better, the killed value is between 0 and 1, and the corrosion-resistant for wood-rotting fungi is grade A. Copyright © 2013 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

WOOD PRODUCTS IN THE WASTE STREAM: CHARACTERIZATION AND COMBUSTION EMISSIONS - VOLUME 2. APPENDICES

EPA Science Inventory

The report gives results of a study of technical, public policy, and regulatory issues that affect the processing and combustion of waste wood for fuel. (NOTE: Waste wood is wood that is separated from a solid-waste stream, processed into a uniform-sized product, and reused for o...

Chapter 15: Discussion on Prior Commercial Wood Preservation Systems That Performed Less Well Than Expected

Treesearch

Tor P. Schultz; Darrel D. Nicholas; Patti Lebow

2014-01-01

This article reviews five prior commercial wood preservatives that had efficacy concerns. A common factor among all five systems was minimal or no field testing of the proposed system prior to commercialization. Also, the formulation of a successful preservative was twice changed, and one successful system was employed with a new wood species. There is no intent to...

Selection, production, procurement, and use of preservative treated wood : supplementing federal specification TT-W-571

Treesearch

Lee R. Gjovik; Roy H. Baechler

1977-01-01

This report has been prepared to supplement Federal Specification TT-W-571 “Wood Preservation: Treating Practices.” developed for the General Services Administration by the U.S. Department of Agriculture, Forest Service, Forest Products Laboratory, the Specification is used by Federal agencies, State agencies, and private users in procuring preservative-treated wood....

Comparison of performance of wood extractives as preservatives in field tests against termites and decay in the USA and Pakistan

Treesearch

Babar Hassan; Sohail Ahmed; Mark Mankowski; Grant Kirker

2017-01-01

Increasing environmental regulations have limited the use of certain broad spectrum synthetic pesticides as wood preservatives creating a need for more environmentally benign wood preservative systems. Biocidal compounds from natural products have been proposed as alternatives to commercial wood preservatives, but field data from long term performance testing is...

Chapter 14: Evaluating the Leaching of Biocides from Preservative-Treated Wood Products

Treesearch

Stan T. Lebow

2014-01-01

Leaching of biocides is an important consideration in the long term durability and any potential for environmental impact of treated wood products. This chapter discusses factors affecting biocide leaching, as well as methods of evaluating rate and quantity of biocide released. The extent of leaching is a function of preservative formulation, treatment methods, wood...

Wood preservation

Treesearch

Rebecca E. Ibach

1999-01-01

When left untreated in many outdoor applications, wood becomes subject to degradation by a variety of natural causes. Although some trees possess naturally occurring resistance to decay (Ch. 3, Decay Resistance), many are in short supply or are not grown in ready proximity to markets. Because most commonly used wood species, such as Southern Pine, ponderosa pine, and...

Performance of Northeastern United States wood species treated with copper based preservatives: 10 year above-ground decking evaluation

Treesearch

S. T. Lebow; S. A. Halverson

2015-01-01

Research was conducted to evaluate the decking performance of northeastern United States wood species treated with copper based preservatives. Decking specimens were treated with one of four wood preservatives and exposed near Madison, Wisconsin. Specimens were evaluated for biological attack and dimensional stability. After 10 years, none of the preservative treated...

THE TREATMENT OF CONTAMINATED WATER AT REMEDIAL WOOD PRESERVING SITES

EPA Science Inventory

Contaminated groundwater and surface water have posed a great challenge in restoring wood preserving sites to beneficial use. Often contaminated groundwater plumes extend far beyond the legal property limits, adversely impacting drinking water supplies and crop lands. To contain,...

Gasification of Wood and Non-wood Waste of Timber Production as Perspectives for Development of Bioenergy

NASA Astrophysics Data System (ADS)

Kislukhina, Irina A.; Rybakova, Olga G.

2018-03-01

The article deals with biomass gasification technology using the gasification plant running on wood chips and pellets, produced from essential oils waste (waste of coniferous boughs). During the study, the authors solved the process task of improving the quality of the product gas derived from non-wood waste of timber production (coniferous boughs) due to the extraction of essential oils and the subsequent thermal processing of spent coniferous boughs at a temperature of 250-300°C degrees without oxygen immediately before pelleting. The paper provides the improved biomass gasification process scheme including the grinding of coniferous boughs, essential oil distillation and thermal treatment of coniferous boughs waste and pelletizing.

WOOD PRODUCTS IN THE WASTE STREAM: CHARACTERIZATION AND COMBUSTION EMISSIONS - VOLUME 1. TECHNICAL REPORT

EPA Science Inventory

The report gives results of a study of technical, public policy, and regulatory issues that affect the processing and combustion of waste wood for fuel. (NOTE: Waste wood is wood that is separated from a solid-waste stream, processed into a uniform-sized product, and reused for o...

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

PubMed

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

SOLIDIFICATION/STABILIZATION: A LOW COST TREATMENT FOR WOOD PRESERVING SITES

EPA Science Inventory

Over 600 curent and former wood preserving sites have been identified across the U.S. Many of these have been placed on the EPA Superfund NPL (National Priorities List). Most of these sites contain soils contaminated with pentachlorophenol, dioxins, and/or creosote. Treatability...

State-of-the-art of waste wood supply chain in Germany and selected European countries.

PubMed

Garcia, Carlos A; Hora, Guido

2017-12-01

According to the statistic office of the European Union (Eurostat), Germany is the main producer of waste wood in Europe followed by France, United Kingdom, Italy and Finland. Based on the characteristics of the waste wood, it can be classified in four (4) categories: A I, A II, A III and A IV. This paper focuses in the A I waste wood since is the only category able to be used directly for both material and energy purposes without a previously pre-treatment. Currently, most of this waste wood is used for direct energy production due to the previous government legislation that promoted its use directly in incineration facilities. However, the newest Renewable Energy Act (EEG 2017) may promote the cascade-use of A I waste wood prior to be intended for energy purposes. Nonetheless, the government incentives to the energy sector is not the only bottleneck that the use of A I waste wood as raw material in the wood-based industry has to overcome. The peak availability, collection logistics (collection centers and transportation) and recycling facility location are some of the parameters that must be considered in order to design the "best" supply chain network for A I waste wood. This work presents a detailed description of the effect of the hierarchical strategic decision in the proper design of the waste wood supply chain. Additionally, the global picture of waste wood recycling in different European countries (UK, Italy and Finland) is briefly presented. Copyright © 2017. Published by Elsevier Ltd.

CCA-treated wood disposed in landfills and life-cycle trade-offs with waste-to-energy and MSW landfill disposal.

PubMed

Jambeck, Jenna; Weitz, Keith; Solo-Gabriele, Helena; Townsend, Timothy; Thorneloe, Susan

2007-01-01

Chromated copper arsenate (CCA)-treated wood is a preservative treated wood construction product that grew in use in the 1970s for both residential and industrial applications. Although some countries have banned the use of the product for some applications, others have not, and the product continues to enter the waste stream from construction, demolition and remodeling projects. CCA-treated wood as a solid waste is managed in various ways throughout the world. In the US, CCA-treated wood is disposed primarily within landfills; however some of the wood is combusted in waste-to-energy (WTE) facilities. In other countries, the predominant disposal option for wood, sometimes including CCA-treated wood, is combustion for the production of energy. This paper presents an estimate of the quantity of CCA-treated wood entering the disposal stream in the US, as well as an examination of the trade-offs between landfilling and WTE combustion of CCA-treated wood through a life-cycle assessment and decision support tool (MSW DST). Based upon production statistics, the estimated life span and the phaseout of CCA-treated wood, recent disposal projections estimate the peak US disposal rate to occur in 2008, at 9.7 million m(3). CCA-treated wood, when disposed with construction and demolition (C&D) debris and municipal solid waste (MSW), has been found to increase arsenic and chromium concentrations in leachate. For this reason, and because MSW landfills are lined, MSW landfills have been recommended as a preferred disposal option over unlined C&D debris landfills. Between landfilling and WTE for the same mass of CCA-treated wood, WTE is more expensive (nearly twice the cost), but when operated in accordance with US Environmental Protection Agency (US EPA) regulations, it produces energy and does not emit fossil carbon emissions. If the wood is managed via WTE, less landfill area is required, which could be an influential trade-off in some countries. Although metals are concentrated

Treated wood preservatives linked to aquatic damage, human illness, and death--a societal problem.

PubMed

Edlich, Richard F; Winters, Kathryne L; Long, William B

2005-01-01

On February 12, 2002, the US Environmental Protection Agency (EPA) announced a voluntary decision by industry to move consumer use of treated lumber products away from a variety of pressure-treated wood that contains arsenate (As) by December 31, 2003, in favor of new alternative wood preservatives. Chromated copper arsenate (CCA) is a chemical mixture consisting of three pesticidal compounds (As, chromium, and copper) registered for wood preservative uses. CCA is injected into wood by a process that uses high pressure to saturate wood products with the chemical. Only people who have received the proper safety training should use CCA to treat wood products. Around the home, CCA-treated wood is commonly used for decks, walkways, fences, gazebos, boat docks, and playground equipment. Other common uses of CCA-treated wood include highway noise barriers, sign posts, utility posts, and retaining walls. As of January 1, 2004, the EPA is no longer allowing CCA products to be used to treat wood intended for any of these residential uses. This decision will facilitate the voluntary transition to new alternative wood preservatives that do not contain As in both the manufacturing and retail sectors. To its credit, the EPA has developed consumer safety information sheets, hanging signs, end signs, and bin stickers that provide comprehensive information about the dangers of CCA-treated wood, use-site, and handling precautions. The EPA has not concluded that CCA-treated wood poses any unreasonable risk to the public or the environment. Nevertheless, As is a known human carcinogen and, thus, the EPA believes that any reduction in the levels of potential exposure to As is desirable. The toxicologic manifestations have been primarily related to the effects of As exposure from drinking water sources and include the following: acute poisoning incidents, cardiovascular effects, diabetes mellitus, and cancer. Understanding the biomethylation of As is central to elucidating its action

Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

PubMed

Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

2015-12-01

The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome. Copyright © 2015 Elsevier Ltd. All rights reserved.

BIOREMEDIATION TREATABILITY STUDIES OF CONTAMINATED SOILS AT WOOD PRESERVING SITES

EPA Science Inventory

Bioremediationis used frequently at sites contaminated with organic hazardous chemical where releases from processing vessels and the mismanagement of reagents and generated waste have contributed to significant impairment of the environment. At wood treater sites, process reagen...

Chemical yields from low-temperature pyrolysis of CCA-treated wood

Treesearch

Qirong Fu; Dimitris Argyropolous; Lucian Lucia; David Tilotta; Stan Lebow

2009-01-01

Low-temperature pyrolysis offers a feasible option for wood-waste management and the recovery of a variety of useful chemicals. The effect of chromated copper arsenate (CCA) wood preservative on the yield and composition of various pyrolysis products was investigated in the present research. A novel quantitative 31P nuclear magnetic resonance (...

Transformation and Release of Micronized Cu used as a Wood Preservative in Treated Wood in Wetland Soil

EPA Science Inventory

Micronized Cu (µ-Cu) is used as a wood preservative, replacing toxic Chromated Copper Arsenates. Micronized Cu is Malachite [Cu2CO3(OH)2] that has been milled to micron/submicron particles, many with diameters less than 100 nm, and then mixed with quat or azol biocides. I...

Transformation and Release of Micronized Cu Used as a Wood Preservative in Treated Wood in Wetland Soil.

EPA Science Inventory

Micronized Cu (µ-Cu) is used as a wood preservative, replacing toxic Chromated Copper Arsenates. Micronized Cu is Malachite [Cu2CO3(OH)2] that has been milled to micron/submicron particles, many with diameters less than 100 nm, and then mixed with quat or azol biocides. I...

Evaluating the corrosiveness of southern pine treated with several wood preservatives using electrochemical techniques

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; Donald S. Stone

2009-01-01

Chromated copper arsenate (CCA), the most widely used wood preservative of the past 50 years, has been replaced for most uses with alkaline-copper systems such as alkaline copper quaternary (ACQ), copper azole (CuAz) and micronized copper quaternary (MCQ). Preliminary research using high-temperature, high-humidity environments have shown that some of these wood...

Migration of wood-preserving chemicals in contaminated groundwater in a sand aquifer at Pensacola, Florida

USGS Publications Warehouse

Goerlitz, D.F.; Troutman, D.E.; Godsy, E.M.; Franks, B.J.

1985-01-01

Operation of a wood-preserving facility for nearly 80 years at Pensacola, FL, contaminated the near-surface groundwater with creosote and pentachlorophenol. The major source of aquifer contamination was unlined surface impoundments that were in direct hydraulic contact with the groundwater. Episodes of overtopping the impoundments and overland flow of treatment liquor and waste were also significant to the migration and contamination of the groundwater. Solutes contaminating the ground-water are mainly naphthalene and substituted phenols. Sorption did not influence retardation of solutes in transport in the groundwater. Phenol and the mono substituted methylphenols appear to be undergoing bio-transformation. Pentachlorophenol (PCP) was not found in significant concentrations in the groundwater possibly because the solubility of PCP is approximately 5 mg/L at pH 6, near the average acidity for the groundwater.

Ground-contact durability of wood treated with borax-copper preservative

Treesearch

Stan T. Lebow; Bessie Woodward; Patricia K. Lebow

2007-01-01

This study evaluated the ability of a borax-copper(BC) preservative to protect wood exposed in ground contact. Southern pine sapwood stakes were pressure-treated with 0.9%, 1.4%, 2.3%, and 4.7% BC solution concentrations and placed into the ground at test sites near Mississippi, or Madison, Wisconsin. Untreated stakes and stakes treated with 1% chromated copper...

Comparison of Wood Preservatives in Stake Tests (1983 Progress Report).

DTIC Science & Technology

1983-12-01

to "X-disease" (hyperkeratosis) in cattle . These oils are therefore not recommended for preservative treatment of wood with which cattle 4 may come in...welam Molmol(W sies saidal) liss. 6.1 of- - - - a. - 0 a . .F a e o a mWi is . 0 .1 a s - - - - - m - - * - l e t a 1 4i .8 blawaeted castrate asis

North American Wood Waste Forum: Summary of Group Feedback, 2-3, 2012

Treesearch

Bob Falk

2012-01-01

This report summarizes the feedback and recommendations of the North American Wood Recovery Group. This report summarizes the barriers and opportunities in wood recovery, reuse, and recycling as identified by this group of stakeholders from the wood industry, waste industry, and relevant government agencies.

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste...

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste...

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste...

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2010 CFR

2010-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste...

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste...

Preservation of hyphal-forming brown- and white-rot wood-inhabiting basidiomycetes

Treesearch

Suki C. Croan

2001-01-01

Lyophilization is an excellent technique for the long-term preservation of hyphal-forming brown-and white-rot wood-inhabiting basidiomycotina. However, vegetative mycelial isolates are not lyophilizable. In this study, 10 brown-rot and 10 white-rot basidiomycetous non-sporulating, non-chlamydosporulating, and non-bubillerferous basidiomycetes fungi were tested for...

Energetic valorization of wood waste: estimation of the reduction in CO2 emissions.

PubMed

Vanneste, J; Van Gerven, T; Vander Putten, E; Van der Bruggen, B; Helsen, L

2011-09-01

This paper investigates the potential CO(2) emission reductions related to a partial switch from fossil fuel-based heat and electricity generation to renewable wood waste-based systems in Flanders. The results show that valorization in large-scale CHP (combined heat and power) systems and co-firing in coal plants have the largest CO(2) reduction per TJ wood waste. However, at current co-firing rates of 10%, the CO(2) reduction per GWh of electricity that can be achieved by co-firing in coal plants is five times lower than the CO(2) reduction per GWh of large-scale CHP. Moreover, analysis of the effect of government support for co-firing of wood waste in coal-fired power plants on the marginal costs of electricity generation plants reveals that the effect of the European Emission Trading Scheme (EU ETS) is effectively counterbalanced. This is due to the fact that biomass integrated gasification combined cycles (BIGCC) are not yet commercially available. An increase of the fraction of coal-based electricity in the total electricity generation from 8 to 10% at the expense of the fraction of gas-based electricity due to the government support for co-firing wood waste, would compensate entirely for the CO(2) reduction by substitution of coal by wood waste. This clearly illustrates the possibility of a 'rebound' effect on the CO(2) reduction due to government support for co-combustion of wood waste in an electricity generation system with large installed capacity of coal- and gas-based power plants, such as the Belgian one. Copyright © 2011 Elsevier B.V. All rights reserved.

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Within...

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Within...

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2010 CFR

2010-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Within...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... percent wood wastes, clean lumber and/or yard waste? (a) After the date the initial test for opacity is...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2010 CFR

2010-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... percent wood wastes, clean lumber and/or yard waste? (a) After the date the initial test for opacity is...

Leaching of wood preservative components and their mobility in the environment : summary of pertinent literature

Treesearch

S. Lebow

1996-01-01

Preservative-treated wood is an economical, durable, and aesthetically pleasing building material; therefore, it is a natural choice for construction projects in our National Forests, National Parks, and other public lands. However, we need to ensure that the chemicals used in treated wood do not pose a threat to people or the environment. The purpose of this report is...

Technology Evaluation Report: Biological Treatment of Wood Preserving Site Groundwater by Biotrol, Inc

EPA Science Inventory

Biological Treatment of Wood Preserving SITE Groundwater by Biotrol, Inc. BioTrol's pilot-scale, fixed-film biological treatment system was evaluated for its effectiveness at removing pentachlorophenol from groundwater. The system employs indigenous microorganisms amended wit...

Nondestructive methods of evaluating quality of wood in preservative-treated piles

Treesearch

Xiping Wang; Robert J. Ross; John R. Erickson; John W. Forsman; Gary D. McGinnis; Rodney C. De Groot

2000-01-01

Stress-wave-based nondestructive evaluation methods were used to evaluate the potential quality and modulus of elasticity (MOE) of wood in used preservative-treated Douglas-fir and southern pine piles. Stress wave measurements were conducted on each pile section. Stress wave propagation speeds in the piles were then obtained to estimate their MOE. This was followed by...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of...

40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... Only Wood Waste, Clean Lumber, and Yard Waste § 60.2972 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of appendix A of this...

40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... Only Wood Waste, Clean Lumber, and Yard Waste § 60.2972 How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of appendix A of this...

Emissions of toxic pollutants from co-combustion of demolition and construction wood and household waste fuel blends.

PubMed

Edo, Mar; Ortuño, Núria; Persson, Per-Erik; Conesa, Juan A; Jansson, Stina

2018-07-01

Four different types of fuel blends containing demolition and construction wood and household waste were combusted in a small-scale experimental set-up to study the effect of fuel composition on the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), chlorobenzenes (PCBzs), chlorophenols (PCPhs) and polycyclic aromatic hydrocarbons (PAHs). Two woody materials, commercial stemwood (ST) and demolition and construction wood (DC) were selected because of the differences in their persistent organic pollutants (POPs), ash and metals content. For household waste, we used a municipal solid waste (MSW) and a refuse-derived fuel (RDF) from MSW with 5-20 wt% and up to 5 wt% food waste content respectively. No clear effect on the formation of pollutants was observed with different food waste content in the fuel blends tested. Combustion of ST-based fuels was very inefficient which led to high PAH emissions (32 ± 3.8 mg/kg fuel ). The use of DC clearly increased the total PCDD and PCDF emissions (71 ± 26 μg/kg fuel ) and had a clear effect on the formation of toxic congeners (210 ± 87 ng WHO 2005 -TEQ/kg fuel ). The high PCDD and PCDF emissions from DC-based fuels can be attributed to the presence of material contaminants such as small pieces of metals or plastics as well as timber treated with chromated copper arsenate preservatives and pentachlorophenol in the DC source. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of precipitation pattern on leaching of preservative from treated wood and implications for accelerated testing

Treesearch

Stan Lebow

2014-01-01

There is a need to develop improved accelerated test methods for evaluating the leaching of wood preservatives from treated wood exposed to precipitation. In this study the effects of rate of rainfall and length of intervals between rainfall events on leaching was evaluated by exposing specimens to varying patterns of simulated rainfall under controlled laboratory...

40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... Commenced on or After June 16, 2006 Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2972 How must I monitor opacity for air curtain incinerators that burn only wood waste...

40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... Commenced on or After June 16, 2006 Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2972 How must I monitor opacity for air curtain incinerators that burn only wood waste...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... wood wastes, clean lumber, and/or yard waste? (a) Use Method 9 of 40 CFR part 60, Appendix A to...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... wood wastes, clean lumber, and/or yard waste? (a) Use Method 9 of 40 CFR part 60, Appendix A to...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Code of Federal Regulations, 2012 CFR

2012-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the final...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Code of Federal Regulations, 2014 CFR

2014-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the final...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Code of Federal Regulations, 2013 CFR

2013-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the final...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Code of Federal Regulations, 2010 CFR

2010-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the final...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Code of Federal Regulations, 2011 CFR

2011-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard waste? Table 1 of this subpart specifies the final...

Moisture storage and transport properties of preservative treated and untreated southern pine wood

Treesearch

Samuel L. Zelinka; Samuel V. Glass; Charles R. Boardman; Dominique Derome

2016-01-01

Moisture storage and transport properties of southern pine (Pinus spp.) wood were measured for implementation into hygrothermal models. Specimens were untreated or pressure-treated with alkaline copper quaternary (ACQ) preservative. Moisture storage was characterized with sorption isotherms in the hygroscopic region (high capillary pressures) and...

WASTE REDUCTION PRACTICES AT TWO CHROMATED COPPER ARSENATE WOOD-TREATING PLANTS

EPA Science Inventory

Two chromated copper arsenate (CCA) wood-treating plants were assessed for their waste reduction practices. The objectives of this study were to estimate the amount of hazardous wastes that a well-designed and well-main- tained CCA treatment facility would generate and to iden- t...

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Oisik; Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz; Bhattacharyya, Debes

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted bymore » manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications.« less

Quantities of Arsenic-Treated Wood in Demolition Debris Generated by Hurricane Katrina

PubMed Central

Dubey, Brajesh; Solo-Gabriele, Helena M.; Townsend, Timothy G.

2008-01-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood. PMID:17396637

Evaluation of Mechanical Properties of Plywood Treated with a new Wood Preservative (CEB) Chemical

NASA Astrophysics Data System (ADS)

Kalawate, Aparna; Shahoo, Shadhu Charan; Khatua, Pijus Kanti; Das, Himadri Sekhar

2017-04-01

The objective of this study was to explore the physical and mechanical properties of the plywood made with phenolic glue and rubber wood as core veneer with CEB as a wood preservative. The studied properties were glue shear strength in dry, wet mycological, modulus of elasticity, modulus of rupture and tensile strength in parallel to grain direction as per IS:1734 part-4, 11 and 9 (1983) respectively. Results of the above mentioned tests were compared with the prescribed values given in IS 710-2010 and results revealed that samples conformed the prescribed values.

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard...

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard...

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard...

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard...

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber, and yard...

The role of particle size of particulate nano-zinc oxide wood preservatives on termite mortality and leach resistance

NASA Astrophysics Data System (ADS)

Clausen, Carol A.; Kartal, S. Nami; Arango, Rachel A.; Green, Frederick

2011-06-01

Historically most residential wood preservatives were aqueous soluble metal formulations, but recently metals ground to submicron size and dispersed in water to give particulate formulations have gained importance. In this study, the specific role nano-zinc oxide (ZnO) particle size and leach resistance plays in termite mortality resulting from exposure to particulate ZnO-treated wood was investigated. Southern yellow pine (SYP) sapwood impregnated with three concentrations of two particle sizes (30 and 70 nm) of ZnO were compared to wood treated with soluble zinc sulphate (ZnSO4) preservative for leach resistance and termite resistance. Less than four percent leached from the particulate nano-ZnO-treated specimens, while 13 to 25% of the zinc sulphate leached from the soluble treated wood. Nano-ZnO was essentially non-leachable from wood treated with 5% formulation for the 30-nm particle size. In a no-choice laboratory test, eastern subterranean termites ( Reticulitermes flavipes) consumed less than 10% of the leached nano-ZnO-treated wood with 93 to 100% mortality in all treatment concentrations. In contrast, termites consumed 10 to 12% of the leached ZnSO4-treated wood, but with lower mortality: 29% in the 1% treatment group and less than 10% (5 and 8%, respectively) in the group of wood blocks treated with 2.5 and 5.0% ZnSO4. We conclude that termites were repelled from consuming wood treated with nano-ZnO, but when consumed it was more toxic to eastern subterranean termites than wood treated with the soluble metal oxide formulation. There were no differences in leaching or termite mortality between the two particle sizes of nano-ZnO.

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14815 What are the emission limitations for air curtain incinerators that burn 100...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2012 CFR

2012-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14815 What are the emission limitations for air curtain incinerators that burn 100...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14815 What are the emission limitations for air curtain incinerators that burn 100...

Superfund Record of Decision (EPA Region 6): Texarkana Wood Preserving Company, Texarkana, Bowie County, TX. (First remedial action), September 1990

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The 25-acre Texarkana Wood Preserving site is a former wood treating facility in Bowie County, Texas, within the Days Creek 100-year floodplain. Surrounding land use is industrial, residential, and agricultural. Since the early 1900s, several lumber-related businesses have operated at the site, with documented creosote-based wood treating operations starting in 1954. By 1971, Texarkana was also using creosote and pentachlorophenol for wood preserving. State investigations of the site between 1968 and 1984, showed Texarkana to be negligent or delinquent in fulfilling various permit requirements. The Record of Decision (ROD) addresses onsite contaminated soil near the processing ponds and contaminated groundmore » water in a shallow aquifer. The primary contaminants of concern affecting the soil, sediment, sludge, and ground water are organics including dioxin, PAHs, pesticides, and phenols.« less

Assessment of biodeterioration for the screening of new wood preservatives : calculation of stiffness loss in rapid decay testing

Treesearch

Simon R. Przewloka; Douglas M. Crawford; Douglas R. Rammer; Donald L. Buckner; Bessie M. Woodward; Gan Li; Darrel D. Nicholas

2008-01-01

Demand for the development of environmentally benign wood preservatives has increased significantly. To reduce the evaluation time of prospective candidates, reliable accelerated decay methodologies are necessary for laboratory screening of potential preservatives. Ongoing research at Mississippi State University has focused upon utilizing custom built equipment to...

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2014 CFR

2014-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Reconstruction is Commenced on or After June 16, 2006 Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn...

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Code of Federal Regulations, 2013 CFR

2013-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Reconstruction is Commenced on or After June 16, 2006 Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn...

76 FR 62303 - California: Final Authorization of State Hazardous Waste Management Program Revision

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

...) Land Disposal Restrictions Phase IV--Treatment Standards for Wood Preserving Wastes, Paperwork... the Carbamate Land Disposal Restrictions; (5) Clarification of Standards for Hazardous Waste LDR...) Emergency Revision of the Land Disposal Restrictions (LDR) Treatment Standards for Listed Hazardous Wastes...

SOLIDIFICATION/STABILIZATION FOR REMEDIATON OF WOOD PRESERVING SITES: TREATMENT FOR DIOXINS, PCP, CREOSOTE, AND METALS

EPA Science Inventory

This article discusses the use of solidification/stabilization (S/S) to treat soils contaminated with organic and inorganic chemicals at wood preserving sites. Solidification is defined for this article as making a material into a free standing solid. Stabilization is defined as ...

CCA-TREATED WOOD DISPOSED IN LANDFILLS AND LIFE-CYCLE TRADE-OFFS WITH WASTE-TO-ENERGY AND MSW LANDFILL DISPOSAL

EPA Science Inventory

Chromated copper arsenate (CCA) treated wood is a preservative treated wood construction product that grew in use in the 1970s for both residential and industrial applications. In the U.S. CCA-treated wood is disposed primarily within landfills, however some of the wood is combu...

Application of biochar from food and wood waste as green admixture for cement mortar.

PubMed

Gupta, Souradeep; Kua, Harn Wei; Koh, Hui Jun

2018-04-01

Landfilling of food waste due to its low recycling rate is raising serious concerns because of associated soil and water contamination, and emission of methane and other greenhouse gases during the degradation process. This paper explores feasibility of using biochar derived from mixed food waste (FWBC), rice waste (RWBC) and wood waste (mixed wood saw dust, MWBC) as carbon sequestering additive in mortar. RWBC is prepared from boiled plain rice, while FWBC is prepared from combination of rice, meat, and vegetables in fixed proportion. Carbon content in FWBC, RWBC and MWBC were found to be 71%, 66% and 87% by weight respectively. Results show that addition of 1-2wt% of FWBC and RWBC in mortar results in similar mechanical strength as control mix (without biochar). 1wt% of FWBC led to 40% and 35% reduction in water penetration and sorptivity respectively, indicating higher impermeability of mortar. Biochar from mixed wood saw dust performed better in terms of mechanical and permeability properties. Increase in compressive strength and tensile strength by up to 20% was recorded, while depth of water penetration and sorptivity was reduced by about 60% and 38% respectively compared to control. Both FWBC and MWBC were found to act as reinforcement to mortar paste, which resulted in higher ductility than control at failure under flexure. This study suggests that biochar from food waste and mixed wood saw dust has the potential to be successfully deployed as additive in cement mortar, which would also promote waste recycling, and sequester high volume carbon in civil infrastructure. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of inorganic ions on leachability of wood preserving N'N-hydroxynapthalimide (NHA).

Treesearch

S. Nami Kartal; Ben F. Dorau; Stan T. Lebow; Frederick III Green

2004-01-01

Southern yellow pine sapwood stakes and blocks were treated with the sodium salt of the calcium-precipitating compound N’N-hydroxynapthalimide (NHA) and leach tested for 2 weeks using the American Wood-Preservers’ Association (AWPA) standard. Leacheates were measured for NHA using a microplate optical density ultraviolet reader, and leach rates were estimated for tap...

40 CFR 60.2972 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2972 Section 60.2972... PERFORMANCE FOR NEW STATIONARY SOURCES Operator Training and Qualification Air Curtain Incinerators That Burn... incinerators that burn only wood waste, clean lumber, and yard waste? (a) Use Method 9 of appendix A of this...

61. Picking Floor, Large Pile of Waste Rock and Wood ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

61. Picking Floor, Large Pile of Waste Rock and Wood date unknown Historic Photograph, Photographer Unknown; Collection of William Everett, Jr. (Wilkes-Barre, PA), photocopy by Joseph E.B. Elliot - Huber Coal Breaker, 101 South Main Street, Ashley, Luzerne County, PA

Competitiveness in the sawmills and wood preservation industry in the United States and Canada

Treesearch

Rao V Nagubadi; Daowei Zhang

2010-01-01

We examine relative prices, relative productivity levels, and competitiveness in the sawmills and wood preservation industry in the united states and Canada between 1958 and 2003 by using purchasing power parities and bilateral translog production function. Our results show that the competitiveness of the Canadian industy is facilitated by higher relative productivity...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14820 How must I monitor opacity for air curtain incinerators that burn 100 percent...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14820 How must I monitor opacity for air curtain incinerators that burn 100 percent...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or Yard Waste § 62.14820 How must I monitor opacity for air curtain incinerators that burn 100 percent...

Enhancing anti-microbial properties of wood-plastic composites produced from timber and plastic wastes.

PubMed

Wang, Lei; Chen, Season S; Tsang, Daniel C W; Poon, Chi Sun; Ok, Yong Sik

2017-05-01

Considering the resource waste and environmental burden for timber and plastic materials ending up at landfills, this study proposed upcycling wood and plastic waste into value-added wood-plastic composites (WPCs), complying with the standard requirements of flexural strength, thickness swelling, water absorption and thermal insulation. Biological deterioration is a major concern of WPCs. Bacterial survival, fungal attack and algal growth of bactericide-treated WPCs were holistically analysed. Melamine resin was adopted for impregnating anti-microbial agents on the surface. All the agents showed excellent bactericidal rate (Escherichia coli), yet poly-diallyl-dimethyl-ammonium chloride (PolyDADMAC) and silver had the lowest minimum inhibitory concentrations. In terms of weight loss and strength reduction due to fungal decay (Coriolus versicolor), PolyDADMAC, silver and cetyltrimethylammonium bromide (CTAB) imparted the highest resistance on the WPCs. Moreover, PolyDADMAC and copper provided the most protection against algal growth (Chlorella vulgaris), and the former presented durable inhibitory effect. This study presents a value-added solution to wood/plastic waste recycling.

Gene expression analysis of wood decay fungus Fibroporia Radiculosa grown In ACQ-treated wood

Treesearch

Ayfer Akgul; Ali Akgul; Juliet D. Diehl Tang

2018-01-01

Copper-tolerant brown-rot fungi are able todegrade wood treated with copper or copper-based wood preservatives. This research used quantitative reverse transcriptase polymerase chain reaction to explore what genes of the brown-rot fungus, Fibroporia radiculosa, were expressed when the fungus was overcoming the wood preservatives and decaying the...

SOLVENT EXTRACTION AND SOIL WASHING TREATMENT OF CONTAMINATED SOILS FROM WOOD PRESERVING SITES: BENCH SCALE STUDIES

EPA Science Inventory

Bench-scale solvent extraction and soil washing studies were performed on soil samples obtained from three abandoned wood preserving sites that included in the NPL. The soil samples from these sites were contaminated with high levels of polyaromatic hydrocarbons (PAHs), pentachlo...

A Challenge for Radioactive Waste Management: Memory Preservation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Charton, P.; Ouzounian, G.

2008-07-01

ANDRA, the French National Radioactive Waste Management Agency, is responsible for managing all radioactive waste in France over the long term. In the case of short-lived waste for which disposal facilities have a life expectancy of a few centuries, the Agency has set up a system for preserving the memory of those sites. Based on the historical analysis on a comparable timescale and on an appraisal of information-conservation means, a series of regulatory as well as technical provisions was made in order to ensure that sound information be transmitted to future generations. Requirements associated to the provisions deal mostly withmore » legibility and a clear understanding of the information that must be decrypted and understood at least during the lifetime of the facilities (i.e., a few centuries). It must therefore be preserved throughout the same period. Responses to the requirements will be presented notably on various information-recording media, together with the information-diffusion strategy to the different authorities and structures within French society. A concrete illustration of the achievements made so far is the Centre de la Manche Disposal Facility, which was closed down in 1994 and is currently in its post-closure monitoring phase since 2003. In the case of deep geological repositories for long-lived radioactive waste, preserving memory takes a different aspect. First of all, timescales are much longer and are counted in hundreds of thousands of years. It is therefore much more difficult to consider how to maintain the richness of the information over such time periods than it is for short-lived waste. Both the nature and the form of the information to be transmitted must be revised. It would be risky indeed to base memory preservation over the long term on similar mechanisms beyond 1,000 years. Based on the heritage of a much more ancient history, we must seek to find appropriate means in order to develop surface markers and even more to ensure

Hazardous Waste Cleanup: Boricua Wood Processing Incorporated in Toja Baja, Puerto Rico

EPA Pesticide Factsheets

Boricua Wood Processing, Inc. is located on State Road 865 at kilometer 5.5, in Toja Baja. The facility is a manufacturing plant for the pressure injection of liquid preservative solutions into untreated cut lumber. The facility began its activity in 1957.

The challenge of bonding treated wood

Treesearch

Charles R. Frihart

2004-01-01

Wood products are quite durable if exposure to moisture is minimized; however, most uses of wood involve considerable exposure to moisture. To preserve the wood, chemicals are used to minimize moisture pickup, to prevent insect attack, and/or to resist microbial growth. The chemicals used as preservatives can interfere with adhesive bonds to wood. Given the many...

Wood waste decomposition in landfills: An assessment of current knowledge and implications for emissions reporting.

PubMed

O'Dwyer, Jean; Walshe, Dylan; Byrne, Kenneth A

2018-03-01

Large quantities of wood products have historically been disposed of in landfills. The fate of this vast pool of carbon plays an important role in national carbon balances and accurate emission reporting. The Republic of Ireland, like many EU countries, utilises the 2006 Intergovernmental Panel on Climate Change (IPCC) guidelines for greenhouse gas reporting in the waste sector, which provides default factors for emissions estimation. For wood products, the release of carbon is directly proportional to the decomposition of the degradable organic carbon fraction of the product, for which the IPCC provides a value of 0.5 (50%). However, in situ analytic results of the decomposition rates of carbon in landfilled wood do not corroborate this figure; suggesting that carbon emissions are likely overestimated. To assess the impact of this overestimation on emission reporting, carbon decomposition values obtained from literature and the IPCC default factor were applied to the Irish wood fraction of landfilled waste for the years 1957-2016 and compared. Univariate analysis found a statistically significant difference between carbon (methane) emissions calculated using the IPCC default factor and decomposition factors from direct measurements for softwoods (F = 45.362, p = <.001), hardwoods (F = 20.691, p = <.001) and engineered wood products (U = 4.726, p = <.001). However, there was no significant difference between emissions calculated using only the in situ analytic decomposition factors, regardless of time in landfill, location or subsequently, climate. This suggests that methane emissions from the wood fraction of landfilled waste in Ireland could be drastically overestimated; potentially by a factor of 56. The results of this study highlight the implications of emission reporting at a lower tierand prompts further research into the decomposition of wood products in landfills at a national level. Copyright © 2017 Elsevier Ltd. All rights

Influence of corn steep liquor and glucose on colonization of control and CCB (Cu/Cr/B)-treated wood by brown rot fungi

DOE Office of Scientific and Technical Information (OSTI.GOV)

Humar, Miha; Amartey, Sam A.; Pohleven, Franc

2006-07-01

There are increasing problems with regard to the disposal of treated wood waste. Due to heavy metals or arsenic in impregnated wood waste, burning and landfill disposal options are not considered to be environmentally friendly solutions for dealing with this problem. Extraction of the heavy metals and recycling of the preservatives from the wood waste is a much more promising and environmentally friendly solution. In order to study the scale up of this process, copper/chromium/boron-treated wood specimens were exposed to copper tolerant (Antrodia vaillantii and Leucogyrophana pinastri) and copper sensitive wood decay fungi (Gloeophyllum trabeum and Poria monticola). Afterwards, themore » ability of fungal hyphae to penetrate and overgrow the wood specimens was investigated. The fungal growths were stimulated by immersing the specimens into aqueous solution of glucose or corn steep liquor prior to exposure to the fungi. The fastest colonization of the impregnated wood was by the copper tolerant A. vaillantii. Addition of glucose onto the surface of the wood specimens increased the fungi colonization of the specimens; however, immersion of the specimens into the solution of corn steep liquor did not have the same positive influence. These results are important in elucidating copper toxicity in wood decay fungi and for using these fungi for bioremediation of treated wood wastes.« less

Recent trends in preservative treatments for timber bridges

Treesearch

James P. Wacker

2004-01-01

An overview of wood preservatives currently used for timber bridges is presented through a series of case studies from different regions of the United States. New wood species and preservative treatment options for timber bridges have made choosing the appropriate preservative more complicated. The compatibility of wood species and preservative treatment is often...

Modulus of elasticity loss as a rapid indicator of rot-fungal attack on untreated and preservative-treated wood in laboratory tests

Treesearch

Xingxia Ma; Grant T. Kirker; Carol A. Clausen; Mingliang Jiang; Haibin Zhou

2017-01-01

The modulus of elasticity (MOE) of wood is a sensitive indicator of rotfungal attack. To develop an alternative method of rapid assessment of fungal decay in the laboratory, changes in static MOE of untreated and preservative-treated wood were measured during exposure to the brownrot fungus, Gloeophyllum trabeum, and the white-rot fungus, Trametes...

Rooted in Time. Weymouth Woods-Sandhills Nature Preserve: An Environmental Education Designed for Grades 5-6.

ERIC Educational Resources Information Center

North Carolina State Dept. of Environment, Health, and Natural Resources, Raleigh. Div. of Parks and Recreation.

This curriculum guide was developed to provide environmental education through a series of hands-on activities for the classroom and the outdoor setting of Weymouth Woods-Sandhills Nature Preserve, North Carolina. This activity packet, designed for grades 5 and 6, meets established curriculum objectives of the North Carolina Department of Public…

Sodium alginate adhesives as binders in wood fibers/textile waste fibers biocomposites for building insulation.

PubMed

Lacoste, Clément; El Hage, Roland; Bergeret, Anne; Corn, Stéphane; Lacroix, Patrick

2018-03-15

Alginate derived from seaweed is a natural polysaccharide able to form stable gel through carbohydrate functional groups largely used in the food and pharmaceutical industry. This article deals with the use of sodium alginate as an adhesive binder for wood fibres/textile waste fibres biocomposites. Several aldehyde-based crosslinking agents (glyoxal, glutaraldehyde) were compared for various wood/textile waste ratios (100/0, 50/50, 60/40, 70/30 and 0/100 in weight). The fully biomass derived composites whose properties are herewith described satisfy most of the appropriate requirements for building materials. They are insulating with a thermal conductivity in the range 0.078-0.089 W/m/K for an average density in the range 308-333 kg/m3 according to the biocomposite considered. They are semi-rigid with a maximal mechanical strength of 0.84 MPa under bending and 0.44 MPa under compression for 60/40 w/w wood/textile waste biocomposites with a glutaraldehyde crosslinking agent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Demonstration of the efficiency and robustness of an acid leaching process to remove metals from various CCA-treated wood samples.

PubMed

Coudert, Lucie; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Janin, Amélie; Gastonguay, Louis

2014-01-01

In recent years, an efficient and economically attractive leaching process has been developed to remove metals from copper-based treated wood wastes. This study explored the applicability of this leaching process using chromated copper arsenate (CCA) treated wood samples with different initial metal loading and elapsed time between wood preservation treatment and remediation. The sulfuric acid leaching process resulted in the solubilization of more than 87% of the As, 70% of the Cr, and 76% of the Cu from CCA-chips and in the solubilization of more than 96% of the As, 78% of the Cr and 91% of the Cu from CCA-sawdust. The results showed that the performance of this leaching process might be influenced by the initial metal loading of the treated wood wastes and the elapsed time between preservation treatment and remediation. The effluents generated during the leaching steps were treated by precipitation-coagulation to satisfy the regulations for effluent discharge in municipal sewers. Precipitation using ferric chloride and sodium hydroxide was highly efficient, removing more than 99% of the As, Cr, and Cu. It appears that this leaching process can be successfully applied to remove metals from different CCA-treated wood samples and then from the effluents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 1. Technical results. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue-gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 2. Data supplement. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue-gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic and organic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

Preservative treatments for building components

Treesearch

Stan Lebow

2007-01-01

The wood species most commonly used in construction have little natural durability Thus, they are treated with preservatives when used in conditions that favor biodeterioration. The type of preservative used varies with the type of wood product, exposure condition, and specific agent of deterioration. This paper discusses the characteristics of several preservative...

Leaching of CCA-treated wood: implications for waste disposal.

PubMed

Townsend, Timothy; Tolaymat, Thabet; Solo-Gabriele, Helena; Dubey, Brajesh; Stook, Kristin; Wadanambi, Lakmini

2004-10-18

Leaching of arsenic, chromium, and copper from chromated copper arsenate (CCA)-treated wood poses possible environmental risk when disposed. Samples of un-weathered CCA-treated wood were tested using a variety of the US regulatory leaching procedures, including the toxicity characteristic leaching procedure (TCLP), synthetic precipitation leaching procedure (SPLP), extraction procedure toxicity method (EPTOX), waste extraction test (WET), multiple extraction procedure (MEP), and modifications of these procedures which utilized actual MSW landfill leachates, a construction and demolition (C and D) debris leachate, and a concrete enhanced leachate. Additional experiments were conducted to assess factors affecting leaching, such as particle size, pH, and leaching contact time. Results from the regulatory leaching tests provided similar results with the exception of the WET, which extracted greater quantities of metals. Experiments conducted using actual MSW leachate, C and D debris leachate, and concrete enhanced leachate provided results that were within the same order of magnitude as results obtained from TCLP, SPLP, and EPTOX. Eleven of 13 samples of CCA-treated dimensional lumber exceeded the US EPA's toxicity characteristic (TC) threshold for arsenic (5 mg/L). If un-weathered arsenic-treated wood were not otherwise excluded from the definition of hazardous waste, it frequently would require management as such. When extracted with simulated rainwater (SPLP), 9 of the 13 samples leached arsenic at concentrations above 5 mg/L. Metal leachability tended to increase with decreasing particle size and at pH extremes. All three metals leached above the drinking water standards thus possibly posing a potential risk to groundwater. Arsenic is a major concern from a disposal point of view with respect to ground water quality.

Element concentrations in growth rings of trees near an abandoned wood-preserving plant site at Jackson, Tennessee

USGS Publications Warehouse

Yanosky, T.M.; Carmichael, J.K.

1993-01-01

Multielement analysis was performed on individual annual rings of trees growing at and near an abandoned wood-preserving plant site in Jackson, Tennessee, that operated from the early 1930's until 1981. Numerous organic compounds associated with the wood-preserving process have been detected in soils, ground water, and surface water within much of the site. Tree-ring investigations were conducted prior to investigations of ground water downgradient from the site to determine if trees preserved an areal and temporal record of contaminant movement into offsite areas. Increment cores were collected from trees on the abandoned plant site, in downgradient areas west and south of the site, and at two locations presumably unaffected by contamination from the site. Multielement analysis by proton-induced X-ray emission was performed on 5 to 15 individual growth rings from each of 34 trees that ranged in age from about 5 to 50 years. Concentrations of 16 elements were evaluated by analyzing average concentrations within the 1987, 1989, and 1990 rings of all trees; analyzing element-concentration trends along entire core radii; and analyzing element correlations between and among trees. Concentrations of some nutrients and trace metals were elevated in the outermost sapwood rings of some trees that grow south and southwest of the most contaminated part of the site; small trees on the main part of the site and larger trees to the west generally contained fewer rings with elevated concentrations, particularly of trace metals. Concentrations of several elements elevated in tree rings also were elevated in water samples collected from the reach of a stream that flows near the southwestern part of the site. Multielement analysis of each ring of a willow growing along the southern boundary of the site detected extremely large concentrations of chromium, nickel, and iron in rings that formed in 1986 and thereafter. Relative increases in the concentrations of these elements also

What do you need to know to get started with wood and fish waste composting?

Treesearch

Jessie A. Micales

2002-01-01

Mountains and mountains of sawdust, hog fuel and wood chips have been generated by wood-processing mills and accumulated in large mountains in the past. But because of today's environmental con-straints, simply accumulating waste in piles is no longer acceptable. Landfilling may not be an option because of high tipping fees and the high costs of transportation to...

Bone-eating worms from the Antarctic: the contrasting fate of whale and wood remains on the Southern Ocean seafloor

PubMed Central

Glover, Adrian G.; Wiklund, Helena; Taboada, Sergio; Avila, Conxita; Cristobo, Javier; Smith, Craig R.; Kemp, Kirsty M.; Jamieson, Alan J.; Dahlgren, Thomas G.

2013-01-01

We report the results from the first experimental study of the fate of whale and wood remains on the Antarctic seafloor. Using a baited free-vehicle lander design, we show that whale-falls in the Antarctic are heavily infested by at least two new species of bone-eating worm, Osedax antarcticus sp. nov. and Osedax deceptionensis sp. nov. In stark contrast, wood remains are remarkably well preserved with the absence of typical wood-eating fauna such as the xylophagainid bivalves. The combined whale-fall and wood-fall experiment provides support to the hypothesis that the Antarctic circumpolar current is a barrier to the larvae of deep-water species that are broadly distributed in other ocean basins. Since humans first started exploring the Antarctic, wood has been deposited on the seafloor in the form of shipwrecks and waste; our data suggest that this anthropogenic wood may be exceptionally well preserved. Alongside the new species descriptions, we conducted a comprehensive phylogenetic analyses of Osedax, suggesting the clade is most closely related to the frenulate tubeworms, not the vestimentiferans as previous reported. PMID:23945684

Energy from wood waste - A case study

NASA Technical Reports Server (NTRS)

Scola, R.; Daughtrey, K.

1980-01-01

A joint study has been conducted by NASA and Army installations collocated in a dense forest in southwestern Mississippi in order to determine the technical and economic feasibility of using wood waste as a renewable energy source. The study has shown that, with proper forest management, the timber on government lands could eventually support the total energy requirements of 832 billion Btu/yr. Analysis of the current conversion technologies indicates that the direct combustion spreader stoker approach is the best demonstrated technology for this specific application. The economics of the individual powerplants reveal them as attractive alternatives to fossil fueled plants. Environmental aspects are also discussed.

Administrative Settlement Agreement and Order on Consent for Removal Action - Kentucky Wood Preserving Superfund Site. Docket No. 04-2009-3762

EPA Pesticide Factsheets

Contains legal agreement for the Kentucky Wood Preserving Superfund site under CERCLA Sections 104, 106(a), 107 and 122, Winchester, Kentucky, February 9, 2009 Region ID: 04 DocID: 10452978, DocDate: 02-09-2009

Integrated Study of the Potential Application of Remediated CCA Treated Spruce Wood in MDF Production

Treesearch

Ronald Sabo; Altaf H. Basta; Jerrold E. Winandy

2013-01-01

Public health awareness has increased in the past few years regarding the disposal of chromated copper arsenate (CCA) preservative-treated wood wastes. This study demonstrates the potential for using remediated CCA lumber and alternative fiber sources, such as sugar cane bagasse, to produce medium density fiberboard (MDF). The role of both remediated CCA loaded spruce...

Counter-current acid leaching process for copper azole treated wood waste.

PubMed

Janin, Amélie; Riche, Pauline; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Morris, Paul

2012-09-01

This study explores the performance of a counter-current leaching process (CCLP) for copper extraction from copper azole treated wood waste for recycling of wood and copper. The leaching process uses three acid leaching steps with 0.1 M H2SO4 at 75degrees C and 15% slurry density followed by three rinses with water. Copper is recovered from the leachate using electrodeposition at 5 amperes (A) for 75 min. Ten counter-current remediation cycles were completed achieving > or = 94% copper extraction from the wood during the 10 cycles; 80-90% of the copper was recovered from the extract solution by electrodeposition. The counter-current leaching process reduced acid consumption by 86% and effluent discharge volume was 12 times lower compared with the same process without use of counter-current leaching. However, the reuse of leachates from one leaching step to another released dissolved organic carbon and caused its build-up in the early cycles.

The influence of sawmill wood wastes on the distribution and population of macroinvertebrates at Benin River, Niger Delta area, Nigeria.

PubMed

Arimoro, Francis O; Osakwe, Emeka I

2006-05-01

The impact of sawmill wood wastes on the distribution of benthic macroinvertebrates at the Sapele section of Benin River, Niger Delta, Nigeria, was investigated from March 2005 to August 2005. A total of 434 individuals were collected by kick-sampling method, representing 21 taxa of benthic macroinvertebrates. Three stations, 1, 2, and 3, were selected from upstream of the site, receiving wood wastes discharge, the impacted site and its down stream, respectively. Among the water quality variables, conductivity, dissolved oxygen, biochemical oxigen demand (BOD(5)), nitrate-nitrogen, phosphate-phosphorus, transparency, and alkalinity were significantly different (P<0.05) among the stations. Orthogonal comparison by Duncan's multiple range test showed that station 2 (the impacted site) was the cause of the difference. More sensitive species such as Ephemeroptera or Plecoptera were completely absent from station 2, the impacted site. Species abundance was similar in station 1 and 3, indicating that the wood wastes must have adversely affected the distribution of these macroinvertebrates, especially the intolerant species. The wood waste discharge not only altered the water chemistry, but also stimulated the abundance of less-sensitive macroinvertebrate species.

Micronized Copper Wood Preservatives: Efficacy of Ion, Nano, and Bulk Copper against the Brown Rot Fungus Rhodonia placenta

PubMed Central

Civardi, Chiara; Schubert, Mark; Fey, Angelika; Wick, Peter; Schwarze, Francis W. M. R.

2015-01-01

Recently introduced micronized copper (MC) formulations, consisting of a nanosized fraction of basic copper (Cu) carbonate (CuCO3·Cu(OH)2) nanoparticles (NPs), were introduced to the market for wood protection. Cu NPs may presumably be more effective against wood-destroying fungi than bulk or ionic Cu compounds. In particular, Cu- tolerant wood-destroying fungi may not recognize NPs, which may penetrate into fungal cell walls and membranes and exert their impact. The objective of this study was to assess if MC wood preservative formulations have a superior efficacy against Cu-tolerant wood-destroying fungi due to nano effects than conventional Cu biocides. After screening a range of wood-destroying fungi for their resistance to Cu, we investigated fungal growth of the Cu-tolerant fungus Rhodonia placenta in solid and liquid media and on wood treated with MC azole (MCA). In liquid cultures we evaluated the fungal response to ion, nano and bulk Cu distinguishing the ionic and particle effects by means of the Cu2+ chelator ammonium tetrathiomolybdate (TTM) and measuring fungal biomass, oxalic acid production and laccase activity of R. placenta. Our results do not support the presence of particular nano effects of MCA against R. placenta that would account for an increased antifungal efficacy, but provide evidence that attribute the main effectiveness of MCA to azoles. PMID:26554706

Micronized Copper Wood Preservatives: Efficacy of Ion, Nano, and Bulk Copper against the Brown Rot Fungus Rhodonia placenta.

PubMed

Civardi, Chiara; Schubert, Mark; Fey, Angelika; Wick, Peter; Schwarze, Francis W M R

2015-01-01

Recently introduced micronized copper (MC) formulations, consisting of a nanosized fraction of basic copper (Cu) carbonate (CuCO3·Cu(OH)2) nanoparticles (NPs), were introduced to the market for wood protection. Cu NPs may presumably be more effective against wood-destroying fungi than bulk or ionic Cu compounds. In particular, Cu- tolerant wood-destroying fungi may not recognize NPs, which may penetrate into fungal cell walls and membranes and exert their impact. The objective of this study was to assess if MC wood preservative formulations have a superior efficacy against Cu-tolerant wood-destroying fungi due to nano effects than conventional Cu biocides. After screening a range of wood-destroying fungi for their resistance to Cu, we investigated fungal growth of the Cu-tolerant fungus Rhodonia placenta in solid and liquid media and on wood treated with MC azole (MCA). In liquid cultures we evaluated the fungal response to ion, nano and bulk Cu distinguishing the ionic and particle effects by means of the Cu2+ chelator ammonium tetrathiomolybdate (TTM) and measuring fungal biomass, oxalic acid production and laccase activity of R. placenta. Our results do not support the presence of particular nano effects of MCA against R. placenta that would account for an increased antifungal efficacy, but provide evidence that attribute the main effectiveness of MCA to azoles.

Field testing of the experimental wood preservative N'N-naphtaloylhydroxylamine : five and eight years results

Treesearch

Frederick Green; Rachel A. Arango; Stan T. Lebow

2010-01-01

Field trials were designed to evaluate the ability of the experimental wood preservative N’N-naphthaloylhydroxylamine (NHA) to inhibit fungal decay and termite damage at the USDA Harrison Experimental Forest (HEF) in Saucier, MS. Twenty replicate 19 x 19 x 457 mm (0.75 x 0.75 x 18 in.) southern yellow pine stakes and 10 replicate 19 x 19 x 76 mm (0.75 x 0.75 x 3 in.)...

Production and characterization of activated carbon from wood wastes

NASA Astrophysics Data System (ADS)

Ramirez, A. P.; Giraldo, S.; Ulloa, M.; Flórez, E.; Y Acelas, N.

2017-12-01

Cedarwood (Cedrela Angustifolia) and teak (Tectona Grandis) woods are typically used for furniture manufacture because they have high durability, are light and easy to work. During these manufacturing process, large amount of these wastes is generated causing disposal environmental problems. In this paper, the residual wastes (sawdust) of Cedar (C) and Teak (T) are transformed into an activated material. The chemical composition of both biomass (C and T) was determinate by TGA (Thermogravimetric Analysis). Activated materials were characterized in surface area following the BET (Brunauer, Emmett and Teller) method, morphology using SEM (Scanning Electron Microscopy) and to know their functional groups a FTIR (Fourier Transform Infrared Spectroscopy) analysis was done. Their adsorption capacity was evaluated by removal of Methylene Blue (MB) and Congo Red (CR) from aqueous solutions.

Preservative treatment of wood for farm use

Treesearch

J. Oscar Blew

1965-01-01

With all the favorable properties that contribute to its wide use in farming, wood nevertheless needs to be used intelligently, and protected from certain natural enemies. For example, while some species of wood are naturally resistant to attack by decay fungi and harmful insects, most species lack adequate resistance when exposed to attack, This is not serious when...

36 CFR 13.1110 - May I collect or burn interstadial wood?

Code of Federal Regulations, 2010 CFR

2010-07-01

... interstadial wood? 13.1110 Section 13.1110 Parks, Forests, and Public Property NATIONAL PARK SERVICE... and Preserve General Provisions § 13.1110 May I collect or burn interstadial wood? Collecting or burning interstadial wood (aged wood preserved in glacial deposits) is prohibited. ...

36 CFR 13.1110 - May I collect or burn interstadial wood?

Code of Federal Regulations, 2011 CFR

2011-07-01

... interstadial wood? 13.1110 Section 13.1110 Parks, Forests, and Public Property NATIONAL PARK SERVICE... and Preserve General Provisions § 13.1110 May I collect or burn interstadial wood? Collecting or burning interstadial wood (aged wood preserved in glacial deposits) is prohibited. ...

Effect of natural ageing on volume stability of MSW and wood waste incineration residues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gori, Manuela, E-mail: manuela.gori@dicea.unifi.it; Bergfeldt, Britta; Reichelt, Jürgen

2013-04-15

Highlights: ► Natural weathering on BA from MSW and wood waste incineration was evaluated. ► Type of mineral phases, pH and volume stability were considered. ► Weathering reactions effect in improved stability of the materials. - Abstract: This paper presents the results of a study on the effect of natural weathering on volume stability of bottom ash (BA) from municipal solid waste (MSW) and wood waste incineration. BA samples were taken at different steps of treatment (fresh, 4 weeks and 12 weeks aged) and then characterised for their chemical and mineralogical composition and for volume stability by means of themore » mineralogical test method (M HMVA-StB), which is part of the German quality control system for using aggregates in road construction (TL Gestein-StB 04). Changes of mineralogical composition with the proceeding of the weathering treatment were also monitored by leaching tests. At the end of the 12 weeks of treatment, almost all the considered samples resulted to be usable without restrictions in road construction with reference to the test parameter volume stability.« less

A comparison of wood preservatives in posts in southern Mississippi : results from a half-decade of testing

Treesearch

Mike H. Freeman; Douglas Crawford; Patricia Lebow; James A. Brient

2005-01-01

Wood preservatives extend the useful service life of all wooden commodities used above ground and in ground contact, Over SO years ago, the USDA-Forest Products Lab established tests in a high decay and high termite hazard zone in southern Mississippi. During the last five decades, periodic reports have been issued by researchers located at the USDA-FPL, in Madison, WI...

The Statistics of wood assays for preservative retention

Treesearch

Patricia K. Lebow; Scott W. Conklin

2011-01-01

This paper covers general statistical concepts that apply to interpreting wood assay retention values. In particular, since wood assays are typically obtained from a single composited sample, the statistical aspects, including advantages and disadvantages, of simple compositing are covered.

Comparison of Wood Preservatives in Stake Tests (1981 Progress Report).

DTIC Science & Technology

1981-12-01

infected with Trichoderma mold, plus other selected species such as oak, Douglas-fir, and Engelmann spruce. Southern pine untreated control stakes...acetylated wood, cyanoethylated wood, that with thiamine destroyed, chemically modified wood, wood infected with Trichoderma mold, embedded fiberboard (western...14 toA4 41U(4 a ...- 44- Table 31.--Condition of southern pine stakes (2 x 4 in. nominal x 18 in.) of uninfected and Trichoderma mcid-infected wood

Electrochemical corrosion testing of fasteners in extracts of treated wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; Donald S. Stone

2008-01-01

A recent change in wood preservatives has highlighted the need for a rapid, quantitative test to measure the corrosion rates of metals in contact with treated wood that could be used to evaluate new fasteners or new wood preservatives. A new method was developed where polarisation resistance tests were conducted on fasteners exposed to a water extract of wood treated...

Advances in corrosion testing of metals in contact with treated wood

Treesearch

Samuel Zelinka; D.S. Stone

2010-01-01

A January 2004 change in the regulation of wood preservatives used in the U.S.has increased the use of newer wood preservatives, such as alkaline copper quaternary (ACQ) and copper azole (CuAz). These preservatives contain high amounts of cupric ions, which may be reduced to copper metal at the expense of less noble steel and galvanized fasteners in the wood....

A review of double-diffusion wood preservation suitable for Alaska.

Treesearch

K. Josephine Pavia

2006-01-01

Currently, all treated lumber used in Alaska is imported from the 48 contiguous states and Canada because there are no wood-treating facilities in Alaska. This report explores conventional and alternative wood-treating methods and reviews previous studies and laboratory tests on treated wood. In investigating wood treatment as a possible processing option for Alaska...

Unique preservative tolerance in Tyromyces palustris

Treesearch

Frederick Green; Rachel A. Arango; Carol A. Clausen

2005-01-01

Fungal tolerance to wood preservatives has been critically important for many years. The tolerance of type cultures to common wood preservatives is, in fact, noted in the AWPA Standards [1]. Gloeophyllum trabeum Mad-617, for example, is particularly tolerant to phenolic and arsenic compounds. One important group of decay fungi that has been studied extensively are...

A PROBABILISTIC EXPOSURE ASSESSMENT FOR CHILDREN WHO CONTACT CCA-TREATED PLAYSETS AND DECKS USING THE STOCHASTIC HUMAN EXPOSURE AND DOSE SIMULATION (SHEDS) MODEL FOR THE WOOD PRESERVATIVE EXPOSURE SCENARIO

EPA Science Inventory

The U.S. Environmental Protection Agency has conducted a probabilistic exposure and dose assessment on the arsenic (As) and chromium (Cr) components of Chromated Copper Arsenate (CCA) using the Stochastic Human Exposure and Dose Simulation model for wood preservatives (SHEDS-Wood...

36 CFR 13.1110 - May I collect or burn interstadial wood?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false May I collect or burn... and Preserve General Provisions § 13.1110 May I collect or burn interstadial wood? Collecting or burning interstadial wood (aged wood preserved in glacial deposits) is prohibited. ...

36 CFR 13.1110 - May I collect or burn interstadial wood?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false May I collect or burn... and Preserve General Provisions § 13.1110 May I collect or burn interstadial wood? Collecting or burning interstadial wood (aged wood preserved in glacial deposits) is prohibited. ...

Superfund Record of Decision (EPA Region 6): Texarkana Wood Preserving Company, Operable Unit 2, Texarkana, TX, September 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This decision document presents the selected remedial action for Operable Unit Two for the Texarkana Wood Preserving Company (TWPC) Superfund Site (Site) in Texarkana, Texas. This operable unit is the second of two operable units planned for the Site. Operable Unit Two involves remediation of the deeper ground water contaminated above the action levels in a limited area of the Silty Sand Zone around Monitoring Well-16.

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint

DOEpatents

Moens, Luc

1995-01-01

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350.degree. and 375.degree. C. to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan.

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint

DOEpatents

Moens, L.

1995-07-11

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350 and 375 C to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan. 2 figs.

REGULATORY PERSPECTIVE ON MANAGING RISKS AT WOOD TREATING SITES

EPA Science Inventory

Over 700 sites in the United States have been identified where wood preserving operations have been conducted. The most common types of wood preservatives found at these sites are creosote, pentachlorophenol (PCP), and copper chromated arsenate (CCA). When properly used and dis...

Exposure test of fasteners in preservative-treated wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2006-01-01

This study examined nails and screws exposed to ACQ-treated wood for up to 12 months in a controlled environment. The environment (27ºC, 100% relative humidity) was chosen so that comparisons could be made with previous exposure tests run using CCA-treated wood in the same environment. Five types of fasteners (common 8d nail, hot-dipped galvanized 8d nail, 4d aluminum...

Inventories of woody residues and solid wood waste in the United States, 2002

Treesearch

David B. McKeever

2004-01-01

Large amounts of woody residues and wood waste are generated annually in the United States. In 2002, an estimated 240 million metric tons was generated during the extraction of timber from the Nation’s forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in...

Health assessment for Texarkana Wood Preserving Company, Texarkana, Bowie County, Texas, Region 6. CERCLIS No. TXD008056152. Addendum. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Texarkana Wood Preserving Company (TWPC) is a National Priorities List site located in northeastern Texas, at the southern extremity of the City of Texarkana in Bowie County. The TWPC site has been used for various lumber-related activities since the early 1900s and for creosoting operations since the early 1950s. Contaminated soils, groundwater, surface water, and surface water sediments have been detected on and off of the TWPC site. The primary contaminants of concern are polycyclic aromatic hydrocarbons, pentachlorophenol, chlorinated dibenzodioxins and chlorinated dibenzofurans. The population at greatest risk of exposure to these contaminants are on-site workers engaged in remedialmore » activities. There are currently no residences or businesses located immediately adjacent to the site and no documentation that contaminated groundwater is being used for potable purposes. The Texarkana Wood Preserving Company site has been evaluated by the Agency for Toxic Substances and Disease Registry (ATSDR) Health Activities Recommendation Panel (HARP) for appropriate follow-up with respect to health activities.« less

Environmental impact of preservative-treated wood in a wetland boardwalk.

Treesearch

Stan T. Lebow; Patricia K. Lebow; Daniel O. Foster; Kenneth M. Brooks

Forest Service, Bureau of Land Management, and industry partners are cooperating in a study of the leaching and environmental effects of a wetland boardwalk. The construction project is considered bworst casec because the site has high rainfall and large volumes of treated wood were used. Separate boardwalk test sections were constructed using untreated wood or wood...

Variability in evaluating environmental impacts of treated wood.

Treesearch

Stan Lebow; Paul Cooper; Patricia. Lebow

2004-01-01

Preservative treated wood contains components that may be toxic to non-target organisms if released into the environment in sufficient quantities. Numerous studies have been conducted to determine the rate of preservative release from treated wood and/or the extent of their subsequent accumulation in the environment. These studies have produced a wide range of results...

Variability in evaluating environmental impacts of treated wood.

Treesearch

Stan T. Lebow; Paul Cooper; Patricia K. Lebow

2004-01-01

Preservative-treated wood contains components that may be toxic to non-target organisms if released into the environment in sufficient quantities. Numerous studies have been conducted to determine the rate of preservative release from treated wood and/or the extent of their subsequent accumulation in the environment. These studies have produced a wide range of results...

Corrosion of metals in wood : comparing the results of a rapid test method with long-term exposure tests across six wood treatments

Treesearch

Samuel L. Zelinka; Donald S. Stone

2011-01-01

This paper compares two methods of measuring the corrosion of steel and galvanized steel in wood: a long-term exposure test in solid wood and a rapid test method where fasteners are electrochemically polarized in extracts of wood treated with six different treatments. For traditional wood preservatives, the electrochemical extract method correlates with solid wood...

Reusing remediated CCA-treated wood

Treesearch

Carol A. Clausen

2003-01-01

Options for recycling and reusing chromated-copper-arsenate- (CCA) treated material include dimensional lumber and round wood size reduction, composites, and remediation. Size reduction by remilling, shaving, or resawing CCA-treated wood reduces the volume of landfilled waste material and provides many options for reusing used treated wood. Manufacturing composite...

Woody residues and solid waste wood available for recovery in the United States, 2002

Treesearch

David B. McKeever; Robert H. Falk

2004-01-01

Large amounts of woody residues and solid wood waste are generated annually in the United States from the extraction of timber from forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in the construction and demolition of buildings and structures, and in the...

Corrosion avoidance with new wood preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2007-01-01

This article focuses on considerations that need to be made when choosing products, other than stainless steel, to minimize corrosion of metals in contact with treated wood. With so many ?corrosion-resistant? alternative products on the market, it is important to know the fundamental principles of corrosion protection to make informed decisions when designing...

Wood plastic composites from agro-waste materials: Analysis of mechanical properties.

PubMed

Nourbakhsh, Amir; Ashori, Alireza

2010-04-01

This article presents the application of agro-waste materials (i.e., corn stalk, reed stalk, and oilseed stalk) in order to evaluate and compare their suitability as reinforcement for thermoplastics as an alternative to wood fibers. The effects of fiber loading and CaCO(3) content on the mechanical properties were also studied. Overall trend shows that with addition of agro-waste materials, tensile and flexural properties of the composites are significantly enhanced. Oilseed fibers showed superior mechanical properties due to their high aspect ratio and chemical characteristics. The order of increment in the mechanical properties of the composites is oilseed stalk >corn stalk>reed stalk at all fiber loadings. The tensile and flexural properties of the composite significantly decreased with increasing CaCO(3) content, due to the reduction of interface bond between the fiber and matrix. It can be concluded from this study that the used agro-waste materials are attractive reinforcements from the standpoint of their mechanical properties. Copyright 2009 Elsevier Ltd. All rights reserved.

Superfund Record of Decision Amendment (EPA Region 6): Texarkana Wood Preserving Co. , Texarkana, TX, March 13, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This decision document presents an amendment to the selected remedial action for the Texarkana Wood Preserving Co. Superfund Site. This amendment fundamentally changes the Record of Decision (ROD) executed by the Regional Administrator on September 25, 1990. This amended remedy will seal and contain soils contaminated with greater than 3 ppm (parts per million) benzo(a)pyrene equivalents, 2450 ppm total poly aromatic hydrocarbons (PAH), 20 ppb (parts per billion) as 2,3,7,8 TCDD equivalents and 150 ppm pentachlorophenol beneath a soil cap.

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of flymore » ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and

Research update for the treated wood reusing program at the Calhoun Research Station

Treesearch

Cheng Piao; Todd F. Shupe; Leslie Groom; W. Allen Nipper

2009-01-01

The reusability of decommissioned treated wood is primarily dependent on residual preservative retention and residual strength of the wood after service. Therefore, determining the residual preservative retention, bonding performance, and residual strength of spent treated wood can provide vital information to further recycling efforts. This report summarizes the...

Chemical modification : a non-toxic approach to wood preservation

Treesearch

Roger M. Rowell

2005-01-01

Reaction of wood with anhydrides, isocyanates, and epoxides reduces the moisture content of the cell wall and increases the resistance of the modified wood to attack by fungi. As the level of bonded chemical increases. the cell wall equilibrium moisture content decreases and the resistance to attack by white-and brown-rot fungi increases. There is a direct relationship...

The potential of food preservation to reduce food waste.

PubMed

Martindale, Wayne

2017-02-01

While we state it seems unthinkable to throw away nearly a third of the food we produce, we still continue to overlook that we are all very much part of this problem because we all consume meals. The amount of food wasted clearly has an impact on our view of what we think a sustainable meal is and our research suggests food waste is a universal function that can help us determine the sustainability of diets. Achieving sustainability in food systems depends on the utilisation of both culinary skills and knowledge of how foods make meals. These are overlooked by the current food waste debate that is concerned with communicating the problem with food waste rather than solutions to it. We aim to change this oversight with the research presented here that demonstrates the need to consider the role of food preservation to reduce food waste and the requirement for new marketing terms associated with sustainability actions that can be used to stimulate changes in consumption behaviours. We have chosen frozen food to demonstrate this because our research has shown that the use of frozen foods results in 47 % less household food waste than fresh food categories. This has created a step-change in how we view food consumption and has stimulated consumer movements that act across different products and supply chains to enable the consumption of the sustainable meal.

Creosote movement from treated wood immersed in fresh water

Treesearch

Sung-Mo Kang; Jeffrey J. Morrell; John Simonsen; Stan Lebow

2005-01-01

Creosote has a long history of successful use as a wood preservative, but polycyclic aromatic hydrocarbons in this preservative have raised environmental concerns, particularly when creosote-treated wood is used in aquatic environments. A number of models have been developed to predict the risk of creosote use in aquatic environments, but one limitation of these models...

Scaled-up remediation of CCA-treated wood

Treesearch

Carol A. Clausen; William R. Kenealy

2004-01-01

Bioremediation is a novel approach to recycling waste wood treated with chromated copper arsenate (CCA). Remediating CCA-treated waste wood diverts this fiber source from our landfills and provides tangible secondary products from the cleaned fiber. On a laboratory scale, this method, which utilizes oxalic acid extraction and bioleaching with a metal- tolerant...

Hydrogeology and flow of water in a sand and gravel aquifer contaminated by wood-preserving compounds, Pensacola, Florida

USGS Publications Warehouse

Franks, B.J.

1988-01-01

The sand and gravel aquifer in southern Escambia County, Florida , is a typical surficial aquifer composed of quartz sands and gravels interbedded locally with silts and clays. Problems of groundwater contamination from leaking surface impoundments are common in surficial aquifers and are a subject of increasing concern and attention. A potentially widespread contamination problem involves organic chemicals from wood-preserving processes. Because creosote is the most extensively used industrial preservative in the United States, an abandoned wood-treatment plant near Pensacola was chosen for investigation. This report describes the hydrogeology and groundwater flow system of the sand and gravel aquifer near the plant. A three-dimensional simulation of groundwater flow in the aquifer was evaluated under steady-state conditions. The model was calibrated on the basis of observed water levels from January 1986. Calibration criteria included reproducing all water levels within the accuracy of the data (one-half contour interval in most cases). Sensitivity analysis showed that the simulations were most sensitive to recharge and vertical leakance of the confining units between layers 1 and 2, and relatively insensitive to changes in hydraulic conductivity and transmissivity and to other changes in vertical leakance. Applications of the results of the calibrated flow model in evaluation of solute transport may require further discretization of the contaminated area, including more sublayers, than were needed for calibration of the groundwater flow system itself. (USGS)

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

PubMed

Saqib, Naeem; Bäckström, Mattias

2014-12-01

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

Common wood decay fungi found in the Caribbean Basin

Treesearch

D. Jean Lodge

2016-01-01

There are hundreds of wood-decay fungi in the Caribbean Basin, but relatively few of these are likely to grow on manmade structures built of wood or wood-composites. The wood-decay fungi of greatest concern are those that cause brown-rot, and especially brown-rot fungi that are resistant to copper-based wood preservatives. Some fungi that grow in the Caribbean and...

Considerations in recycling of wood-plastic composites

Treesearch

J.E. Winandy; N.M. Stark; C.M. Clemons

2004-01-01

Wood-plastic composite decking has made major advances in material performance, processing and user acceptance. The growth of wood-plastic composite decking in North America has grown from less than 1 % in mid- 0's to over 10% today with growth projected by several studies to reach +20% before the end of this decade (2010). Preservative-treated wood decking...

Wood wastes and residues generated along the Colorado Front Range as a potential fuel source

Treesearch

Julie E. Ward; Kurt H. Mackes; Dennis L. Lynch

2004-01-01

Throughout the United States there is interest in utilizing renewable fuel sources as an alternative to coal and nat-ural gas. This project was initiated to determine the availability of wood wastes and residues for use as fuel in ce-ment kilns and power plants located along the Colorado Front Range. Research was conducted through literature searches, phone surveys,...

How Much Wood Would Wood Waste Waste if None Were Used for Fuel?

ERIC Educational Resources Information Center

Franklin, Ben A.

1978-01-01

The recent trend in using wood for energy is examined with new developments for gaining greater efficiency from an old source. The threat of deforestation is acknowledged and discussed, particularly in relation to Appalachia. (KR)

Comparative study on liquefaction of creosote and chromated copper arsenate (CCA)-treated wood and untreated southern pine wood: effects of acid catalyst content, liquefaction time, temperature, and phenol to wood ratio

Treesearch

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Creosote- and chromated copper arsenate (CCA)-treated wood waste and untreated southern pine wood were liquefied with phenol and sulfuric acid. The effects of sulfuric acid content, liquefaction time, liquefaction temperature, and phenol to wood ratio on liquefaction rate (i.e., wood residue content) were investigated and analyzed by analysis of variance (...

Adhesive bonding of wood treated with ACQ and copper azole preservatives

Treesearch

Linda F. Lorenz; Charles Frihart

2006-01-01

Treated wood has generally been more difficult to bond than untreated wood for a variety of reasons. Alkaline copper quat (ACQ) and copper azole (CA-B), the most prominent substitutes for chromated copper arsenate (CCA), are difficult to bond consistently. Using a phenol-resorcinol- formaldehyde (PRF) adhesive formulated for bonding to CCA-treated wood, we examined the...

Mechanical properties evaluation of extruded wood polymer composites

NASA Astrophysics Data System (ADS)

Zaini, A. S. Syah M.; Rus, Anika Zafiah M.; Rahman, Norherman Abdul; Jais, Farhana Hazwanee M.; Fauzan, M. Zarif; Sufian, N. Afiqah

2017-09-01

The rapidly expanding of interest in the manufacture of composite materials from waste industrial and agricultural materials is due to high demand for environmentally friendly materials. Wood polymer composite (WPC) are being used in many type of applications such as in the automobile, electronic, aerospace industry and construction. Therefore, this research study is to determine the mechanical properties behaviour of WPC after an extended Ultra Violet (UV) irradiation exposure. The fabricated sample has been used and to be compared in this research is consists of rice husk, waste fibre and polypropylene (PP) with 4 different types of WPC which are wood block waste (WBW), wood block virgin (WBV), wood sheet (WS) and wood sheet waste (WSW). The extruded specimens were tested for mechanical properties such as strength under compression, puncture strength and impact resistance, and density. In addition, the specimen has been irradiated with the UV exposure at 5000 hours, 10000 hours and 15000 hours. Generally, the mechanical properties the WPC which made from the recycled material were lower than the WPC from virgin material but the density was comparable between the two products after UV irradiation exposure.

Lignin-Retaining Transparent Wood.

PubMed

Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

2017-09-11

Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Lignin‐Retaining Transparent Wood

PubMed Central

Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin

2017-01-01

Abstract Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light‐transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high‐lignin‐content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK−1, and work‐tofracture of 1.2 MJ m−3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy‐saving buildings. PMID:28719095

Assessment of the potential quality of preservative-treated pilings removed from service : [abstract

Treesearch

Xiping Wang; John W. Forsman; John R. Erickson; Robert J. Ross; Douglas J. Gardner; Gary D. McGinnis; Rodney C. DeGroot

1999-01-01

Preservative-treated wood products are important construction materials. Preservative-treated wood pilings, after removal from service, constitute a major disposal problem for managers of waterfront facilities. For example, approximately 7,000 to 8,000 tons of mechanically or biologically deteriorated wood pilings are currently removed from U.S. naval facilities...

40 CFR 261.35 - Deletion of certain hazardous waste codes following equipment cleaning and replacement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... cleaning and replacement. (a) Wastes from wood preserving processes at plants that do not resume or... parts per trillion (ppt), sample weight of 1000 g, IS spiking level of 1 ppt, final extraction volume of... previously used and the date on which their use ceased in each process at the plant; (3) Formulations...

40 CFR 261.35 - Deletion of certain hazardous waste codes following equipment cleaning and replacement.

Code of Federal Regulations, 2011 CFR

2011-07-01

... cleaning and replacement. (a) Wastes from wood preserving processes at plants that do not resume or... parts per trillion (ppt), sample weight of 1000 g, IS spiking level of 1 ppt, final extraction volume of... previously used and the date on which their use ceased in each process at the plant; (3) Formulations...

Extraction of hexavalent chromium from chromated copper arsenate treated wood under alkaline conditions.

PubMed

Radivojevic, Suzana; Cooper, Paul A

2008-05-15

Information on chromium (Cr) oxidation states is essential for the assessment of environmental and health risks associated with the overall life-cycle of chromated copper arsenate (CCA) treated wood products because of differences in toxicity between trivalent [Cr(III)] and hexavalent [Cr(VI)] chromium compounds. Hypothetical Cr(VI) fixation products were investigated in CCA type C treated sawdust of aspen and red pine during or following preservative fixation by extraction with Cr(VI)-specific extractants. Cr(VI) was found only in alkaline extracts of treated wood. A major source of Cr(VI) was method-induced oxidation of fixed Cr(III) during alkaline extraction, as confirmed by demonstrated oxidation of Cr(III) from CrCl3 treated wood. Oxidation of nontoxic and immobile Cr(III) to toxic and mobile Cr(VI) was facilitated by the presence of wood at pH > 8.5. Thermodynamic equilibrium between Cr(III) and Cr(VI) is affected by pH, temperature, rates of dissolution of CrIII) compounds, and oxygen availability. Results of this study recommend against alkaline extraction protocols for determination of Cr(VI) in treated wood. This Cr oxidation mechanism can act as a previously unrecognized route for generation of hazardous Cr(VI) if CCA treated wood is exposed to alkaline conditions during its production, use, or waste management.

Effects of permethrin treated wood on the subterranean termite Reticulitermes flavipes (Kollar) and comparison of solvent extraction for HPLC analysis of permethrin in wood

Treesearch

Mark Mankowski; Blossie Boyd; Geoffrey Webb

2016-01-01

Permethrin is a common insecticide used in wood preservation. It is an effective synthetic pyrethroid that is considered to be less toxic to higher organisms than organochlorine insecticides. In wood preservation, it can be used in combination with fungicides such as 3-iodo-2-propynyl butyl carbamate (IPBC). Permethrin has a dual mode of action as it is a repellent and...

Use of treated woods in roof assembly.

PubMed

Edlich, Richard F; Winters, Kathryne L; Long, William B; Gubler, K Dean; Britt, L D

2005-01-01

On February 12, 2002, the US Environmental Protection Agency (EPA) announced a voluntary decision by industry to move consumer use of treated lumber products away from a variety of pressure-treated wood that contains Arsenate (As) by December 31, 2003, in favor of new alternative wood preservatives. It is the purpose of this report to outline legislative efforts to ban the use of chromated copper arsenate (CCA)-treated wood for residential roofing in the State of Oregon. At the time that the legislation was introduced, it was coincidental that the National Roofing Contractors Association (NRCA) recommended that CCA-treated wood should not be used in residential roofing. A summary of the report is included in this review. Finally, we discuss some of the potentially harmful environmental hazards of wood preservatives on the environment. In addition to the toxicity of pressure-treated wood on our environment, we point out that wood as well as pressure-treated wood assemblies are highly flammable. Consequently, we recommend the use of residential roofing systems that have Class A fire protection for the homeowner. Because residential roof fires remain a life-threatening danger to residential homeowners in the United States, we describe a national fire prevention program for reducing residential roof fires by use of an Underwriters Laboratories Inc. (UL) and National Fire Protection Association Class A fire-rated roof system.

Nanotechnology : implications for the wood preservation industry

Treesearch

Carol A. Clausen

2007-01-01

Nanotechnology has the potential to greatly impact the wood protection industry through the creation of nanomaterials with unique properties. Nanobiocides may find applications as co-biocides, or may alter treatability properties such as penetration and biocide distribution. Nanocarrier delivery systems may increase the applications for organic biocides through...

Chapter 23: Corrosion of Metals in Wood Products

Treesearch

Samuel L. Zelinka

2014-01-01

The corrosion of metals in contact with wood has been studied for over 80 years, and in most situations wood is not corrosive [1]. Recently, however, the durability of fasteners in preservative--treated wood has become a concern. Changes in legislation and certification in the United States, the European Union, and Australasia have restricted the use of chromated...

Observed relationships between wood density and solution uptake during pressure treatment

Treesearch

Steve Halverson; Stan Lebow

2011-01-01

A better understanding of the relationship between wood properties and solution uptake during pressure treatment could lead to improvements in treatment quality and more efficient use of preservatives. In this study several years of treatment data representing a range of wood species, charge conditions and preservative formulations were analyzed to evaluate the...

Recycling of wood for particle board production: accounting of greenhouse gases and global warming contributions.

PubMed

Merrild, Hanna; Christensen, Thomas H

2009-11-01

The greenhouse gas (GHG) emissions related to the recycling of wood waste have been assessed with the purpose to provide useful data that can be used in accounting of greenhouse gas emissions. Here we present data related to the activities in a material recovery facility (MRF) where wood waste is shredded and foreign objects are removed in order to produce wood chips for use in the production of particleboard. The data are presented in accordance with the UOD (upstream, operational, downstream) framework presented in Gentil et al. (Waste Management & Research, 27, 2009). The GHG accounting shows that the emissions related to upstream activities (5 to 41 kg CO(2)-equivalents tonne( -1) wood waste) and to activities at the MRF (approximately 5 kg CO(2)-equivalents tonne(-1) wood waste) are negligible compared to the downstream processing (-560 to -120 kg CO(2)equivalents tonne(-1) wood waste). The magnitude of the savings in GHG emissions downstream are mainly related to savings in energy consumption for drying of fresh wood for particleboard production. However, the GHG account highly depends on the choices made in the modelling of the downstream system. The inclusion of saved electricity from avoided chipping of virgin wood does not change the results radically (-665 to -125 kg CO(2)-equivalents tonne(- 1) wood waste). However, if in addition it is assumed that the GHG emissions from combustion of wood has no global warming potential (GWP) and that the energy produced from excess wood due to recycling substitutes energy from fossil fuels, here assumed to be coal, potentially large downstream GHG emissions savings can be achieved by recycling of waste wood (-1.9 to -1.3 tonnes CO(2)-equivalents tonne(- 1) wood waste). As the data ranges are broad, it is necessary to carefully evaluate the feasibility of the data in the specific system which the GHG accounting is to be applied to.

The role of extractives in naturally durable wood species

Treesearch

G.T. Kirker; A.B. Blodgett; R.A. Arango; P.K. Lebow; C.A. Clausen

2013-01-01

There are numerous examples of wood species that naturally exhibit enhanced performance and longevity in outside exposure independent of preservative treatment. Wood extractives are largely considered to be the contributing factor when evaluating and predicting the performance of a naturally durable wood species. However, little test methodology exists that focuses on...

Harvester ant bioassay for assessing hazardous chemical waste sites. [Pogonomyrmex owhyeei

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gano, K.A.; Carlile, D.W.; Rogers, L.E.

1985-05-01

A technique was developed for using harvester ants, Pogonomyrmex owhyeei, in terrestrial bioassays. Procedures were developed for maintaining stock populations, handling ants, and exposing ants to toxic materials. Relative toxicities were determined by exposing ants to 10 different materials. These materials included three insecticides, Endrin, Aldrin, and Dieldrin; one herbicide, 2,4-D; three complex industrial waste residuals, wood preservative sludge, drilling fluid, and slop oil; and three heavy metals, copper zinc, and cadium. Ants were exposed in petri dishes containing soil amended with a particular toxicant. Under these test conditions, ants showed no sensitivity to the metals or 2,4-D. Ants weremore » sensitive to the insecticides and oils in repeated tests, and relative toxicity remained consistent throughout. Aldrin was the most toxic material followed by Dieldrin, Endrin, wood preservative sludge, drilling fluid, and slop oil. 12 refs., 2 figs., 2 tabs.« less

Synchrotron applications in wood preservation and deterioration

Treesearch

Barbara L. Illman

2003-01-01

Several non-intrusive synchrotron techniques are being used to detect and study wood decay. The techniques use high intensity synchrotron-generated X-rays to determine the atomic structure of materials with imaging, diffraction, and absorption. Some of the techniques are X-ray absorption near edge structure (XANES), X-ray fluorescence spectroscopy (XFS), X-ray...

Innovations in Wood Protection in the age of Nanotechnology

Treesearch

Carol A. Clausen

2014-01-01

Advances in wood protection based on nanotechnology are being developed to improve resistance of wood products to biodeterioration, reduce environmental impacts from chemical leaching and resist UV degradation of in-service wood. A number of different approaches have been explored. First, the nanometals zinc oxide and copper oxide were evaluated as preservative...

Finishability of CCA pressure-treated wood

Treesearch

Alan Ross; Richard Carlson; William Feist; Steven Bussjaeger

2000-01-01

Thus, a need arose for the development of surface finishes for CCA-treated wood that could address the special requirements of this substrate and provide protection against the ravages of water, sunlight, mildew, and other aspects of weathering and wear. Initially, this need was not addressed, most wood preserving companies had little expertise in surface finishes and...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.Y.; Valenti, J.C.; Tabor, D.G.

The use of waste wood as fuel for producing energy is a promising supplement to fossil fuels for many regions of the country. In addition to recovering energy and conserving landfill space, burning waste wood fuels also mitigates global warming created by fossil fuel combustion. However, the environmental consequences resulting from emissions generated by combustion of waste wood which contains paints, resins, or preservatives are not well understood. The combustion of waste wood treated with chemicals may produce potentially hazardous products of incomplete combustion (PIC) emissions such as dioxins. Characterization of PIC emissions from the combustion of waste wood previouslymore » treated with pentachlorophenol is reported in this study. Utility poles and crossbars are typically treated with a preservative such as pentachlorophenol in order to prolong their service life. They are disposed of by landfilling after being taken out of service. Burning such wood waste in boilers for steam generation becomes an increasingly attractive waste management alternative as it contains substantial energy value and reduces landfilling costs. Pilot-scale combustion tests were conducted under well controlled conditions in a 0.58 MW (2 million Btu/hr) combustor to compare PIC emissions from burning untreated wood and pentachlorophenol-treated wood. Sampling and analyses for a wide variety of PICs, including volatile organic compounds (VOCs), semivolatile organic compounds, and dioxins and furans, were performed to assess the effect of pentachlorophenol preservative present in wood on PIC emissions.« less

Effect of Trichoderma-enriched organic charcoal in the integrated wood protection strategy

PubMed Central

Gandía, Mónica; Marcos, Jose F.; Bas, Maria del Carmen; Fink, Siegfried

2017-01-01

The gradual elimination of chromium from wood preservative formulations results in higher Cu leaching and increased susceptibility to wood decay fungi. Finding a sustainable strategy in wood protection has become of great interest among researchers. The objective of these in vitro studies was to demonstrate the effect of T-720-enriched organic charcoal (biochar) against five wood decay basidiomycetes isolated from strongly damaged poles. For this purpose, the antagonistic potential of Trichoderma harzianum (strain T-720) was confirmed among other four Trichoderma spp. against five brown-rot basidiomycetes in dual culture tests. T-720 was genetically transformed and tagged with the green fluorescent protein (GFP) in order to study its antagonistic mechanism against wood decay basidiomycetes. It was also demonstrated that T-720 inhibits the oxalic acid production by basidiomycetes, a well-known mechanism used by brown-rot fungi to detoxify Cu from impregnated wood. Additionally, this study evaluated the effect of biochar, alone or in combination with T-720, on Cu leaching by different preservatives, pH stabilization and prevention of wood decay caused by five basidiomycetes. Addition of biochar resulted in a significant Cu binding released from impregnated wood specimens. T-720-enriched biochar showed a significant reduction of wood decay caused by four basidiomycetes. The addition of T-720-enriched biochar to the soil into which utility poles are placed may improve the efficiency of Cr-free wood preservatives. PMID:28797118

Effect of Trichoderma-enriched organic charcoal in the integrated wood protection strategy.

PubMed

Ribera, Javier; Gandía, Mónica; Marcos, Jose F; Bas, Maria Del Carmen; Fink, Siegfried; Schwarze, Francis W M R

2017-01-01

The gradual elimination of chromium from wood preservative formulations results in higher Cu leaching and increased susceptibility to wood decay fungi. Finding a sustainable strategy in wood protection has become of great interest among researchers. The objective of these in vitro studies was to demonstrate the effect of T-720-enriched organic charcoal (biochar) against five wood decay basidiomycetes isolated from strongly damaged poles. For this purpose, the antagonistic potential of Trichoderma harzianum (strain T-720) was confirmed among other four Trichoderma spp. against five brown-rot basidiomycetes in dual culture tests. T-720 was genetically transformed and tagged with the green fluorescent protein (GFP) in order to study its antagonistic mechanism against wood decay basidiomycetes. It was also demonstrated that T-720 inhibits the oxalic acid production by basidiomycetes, a well-known mechanism used by brown-rot fungi to detoxify Cu from impregnated wood. Additionally, this study evaluated the effect of biochar, alone or in combination with T-720, on Cu leaching by different preservatives, pH stabilization and prevention of wood decay caused by five basidiomycetes. Addition of biochar resulted in a significant Cu binding released from impregnated wood specimens. T-720-enriched biochar showed a significant reduction of wood decay caused by four basidiomycetes. The addition of T-720-enriched biochar to the soil into which utility poles are placed may improve the efficiency of Cr-free wood preservatives.

CCA retention and its effects on the bonding performance of decommissioned treated wood: a preliminary study

Treesearch

Cheng Piao; Todd F. Shupe; Mark Gibson; Chung Y. Hse

2009-01-01

Chromated copper arsenate (CCA) continues to be widely used as a wood preservative for industrial uses in the U.S. Disposal of treated wood is a potential long-term environmental liability. Current practices for disposing of decommissioned preservative-treated wood include landfilling and incineration, which are increasingly impractical due to environmental...

Statistical analysis of influence of soil source on leaching of arsenic and copper from CCA-C treated wood

Treesearch

Patricia Lebow; Richard Ziobro; Linda Sites; Tor Schultz; David Pettry; Darrel Nicholas; Stan Lebow; Pascal Kamdem; Roger Fox; Douglas Crawford

2006-01-01

Leaching of wood preservatives affects the long-term efficacy and environmental impact of treated wood. Soil properties and wood characteristicscan affectleaching of woad preservatives, but these effects are not well understood. This paper reports a statistical analysis of the effects of soil and wood properties on leaching of arsenic (As) and copper (Cu) from southern...

IN SITU BIOREMEDIATION STRATEGIES FOR ORGANIC WOOD PRESERVATIVES

EPA Science Inventory

Laboratory biotreatability studies evaluated the use of bioventing and biosparging plus groundwater circulation (UVB technology) for their potential abililty to treat soil and groundwater containing creosote and pentachlorophenol. Soils from two former wood-treatment facilities w...

Changing Face of Wood Science in Modern Era: Contribution of Nanotechnology.

PubMed

Mishra, Pawan Kumar; Giagli, Kyriaki; Tsalagkas, Dimitrios; Mishra, Harshita; Talegaonkar, Sushma; Gryc, Vladimír; Wimmer, Rupert

2018-02-14

Wood science and nanomaterials science interact together in two different aspects; a) fabrication of lignocellulosic nanomaterials derived from wood and plant-based sources and b) surface or bulk wood modification by nanoparticles. In this review, we attempt to visualize the impact of nanoparticles on the wood coating and preservation treatments based on a thorough registration of the patent databases. The study was carried out as an overview of the scientifically most followed trends on nanoparticles utilization in wood science and wood protection depicted by recent universal filed patents. This review is exclusively targeted on the solid (timber) wood as a subject material. Utilization of mainly metal nanoparticles as photoprotection, antibacterial, antifungal, antiabrasive and functional component on wood modification treatments was found to be widely patented. Additionally, an apparent minimization in the emission of volatile organic compounds (VOCs) has been succeeded. Bulk wood preservation and more importantly, wood coating, splay the range of strengthening wood dimensional stability and biological degradation, against moisture absorption and fungi respectively. Nanoparticle materials have addressed various issues of wood science in a more efficient and environmental way than the traditional methods. Nevertheless, abundant tests and regulations are still needed before industrializing or recycling these products. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Leaching of flakeboard produced from recycled CCA-treated wood into deionized water

Treesearch

W. Li; T.F. Shupe; Chung-Yun Hse

2004-01-01

The disposal of preservative-treated wood is becoming a larger issue for the forest products industry due to increasing public concern and scrutiny as well as costs associated with traditional disposal, i.e., landfilling. Recycling of preservative-treated wood has great potential. In this study, flakeboard was produced from decommissioned guardrail posts that had been...

Wood Pallets and Landfills - Status and Opportunities for Economic Recovery and Recycling

Treesearch

Philip A. Araman; Robert J. Bush; A.L. Hammett; E. Brad Hager

1998-01-01

Wood pallet recovery, repair, and recycling are sound environmental activities that can reduce both forest resource demands and waste in landfills. Our studies found that 6.16 million tons of wood pallets (or 223.6 million pallets) entered municipal solid waste (MSW) and construction and demolition (C&D) landfill facilities in 1995. At the same time, wood pallet...

A Better Way to Burn Wood.

ERIC Educational Resources Information Center

Robison, Rita

1979-01-01

Wood pyrolysis is a process that burns wood without air, producing gas and oil that are then burned for heat. Now being tested at Maryville College, Tennessee, the process is expected to cut fuel costs, solve a waste disposal problem, and produce charcoal for sale. (Author/MLF)

High-Throughput DNA sequencing of ancient wood.

PubMed

Wagner, Stefanie; Lagane, Frédéric; Seguin-Orlando, Andaine; Schubert, Mikkel; Leroy, Thibault; Guichoux, Erwan; Chancerel, Emilie; Bech-Hebelstrup, Inger; Bernard, Vincent; Billard, Cyrille; Billaud, Yves; Bolliger, Matthias; Croutsch, Christophe; Čufar, Katarina; Eynaud, Frédérique; Heussner, Karl Uwe; Köninger, Joachim; Langenegger, Fabien; Leroy, Frédéric; Lima, Christine; Martinelli, Nicoletta; Momber, Garry; Billamboz, André; Nelle, Oliver; Palomo, Antoni; Piqué, Raquel; Ramstein, Marianne; Schweichel, Roswitha; Stäuble, Harald; Tegel, Willy; Terradas, Xavier; Verdin, Florence; Plomion, Christophe; Kremer, Antoine; Orlando, Ludovic

2018-03-01

Reconstructing the colonization and demographic dynamics that gave rise to extant forests is essential to forecasts of forest responses to environmental changes. Classical approaches to map how population of trees changed through space and time largely rely on pollen distribution patterns, with only a limited number of studies exploiting DNA molecules preserved in wooden tree archaeological and subfossil remains. Here, we advance such analyses by applying high-throughput (HTS) DNA sequencing to wood archaeological and subfossil material for the first time, using a comprehensive sample of 167 European white oak waterlogged remains spanning a large temporal (from 550 to 9,800 years) and geographical range across Europe. The successful characterization of the endogenous DNA and exogenous microbial DNA of 140 (~83%) samples helped the identification of environmental conditions favouring long-term DNA preservation in wood remains, and started to unveil the first trends in the DNA decay process in wood material. Additionally, the maternally inherited chloroplast haplotypes of 21 samples from three periods of forest human-induced use (Neolithic, Bronze Age and Middle Ages) were found to be consistent with those of modern populations growing in the same geographic areas. Our work paves the way for further studies aiming at using ancient DNA preserved in wood to reconstruct the micro-evolutionary response of trees to climate change and human forest management. © 2018 John Wiley & Sons Ltd.

Concepts in the development of new accelerated test methods for wood decay

Treesearch

Darrel D. Nicholas; Douglas Crawford

2003-01-01

Efforts to develop new environmentally friendly wood preservatives are seriously handicapped by the extended time period required to carry out the evaluation needed to establish confidence in the long term performance of new preservative systems. Studies in our laboratory have shown that using strength loss as a measure of the extent of wood decay makes it possible to...

Research on biodeterioration of wood, 1987-1992. 1. Decay mechanisms and biocontrol. Forest Service research paper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Highley, T.L.; Clausen, C.A.; Croan, S.C.

1994-03-01

Growing concerns about the environment present an urgent need for new approaches to preserving wood. Some commonly used preservatives have been banned or restricted in several countries. The research paper first describes current knowledge about how white-and-brown rot fungi decay wood and then delineates research in to problem areas: (1) control of wood decay through targeting biosynthetic and degradative pathways, and (2) biological control (biocontrol) of wood decay through non-decay micro-organisms.

New environmentally-benign concepts in wood protection: the combination of organic biocides and non-biocidal additives

Treesearch

Frederick Green; Tor P. Schultz

2003-01-01

The principal wood preservative for residential use is currently a broad-spectrum biocide which contains As, Cr and Cu. However, the use of totally organic wood preservative systems in certain applications or localities may be required in the future. This will greatly increase the price of treated wood. The combination of organic biocides with non-biocidal additives to...

Protecting wood fences for yard and garden

Treesearch

R. C. De Groot; W. C. Feist; W. E. Eslyn; L. R. Gjovik

For maximum protection against wood decay and termites, use posts that have an in-depth preservative treatment, preferably a pressure treatment for below ground use. When selecting posts of naturally decay-resistant woods, choose posts with mostly heartwood. Horizontal rails require more protection from decay than do vertical boards. In regions of high and moderate...

How much arsenic is released when CCA wood is burned?

Treesearch

Charles K. McMahon; Parshall B. Bush; Edwin A. Woolson

1986-01-01

Abstract. Waterborne salts have been used to preserve wood for many years. One of the more common formulations contains copper, chromium, and arsenic salts and is known as chromated copper arsenate, or CCA. Questions have been raised about the amount of arsenic released when CCA treated wood is burned in wood stoves, fireplaces, or boilers....

CAMP LEJEUNE ENERGY FROM WOOD (CLEW) PROJECT

EPA Science Inventory

The paper discusses EPA's Camp Lejeune Energy from Wood (CLEW) project, a demonstration project that converts wood energy to electric power, and provides waste utilization and pollution alleviation. The 1-MWe plant operates a reciprocating engine-generator set on synthetic gas f...

Some Exploitation Properties of Wood Plastic Hybrid Composites Based on Polypropylene and Plywood Production Waste

NASA Astrophysics Data System (ADS)

Kajaks, Janis; Kalnins, Karlis; Uzulis, Sandris; Matvejs, Juris

2015-12-01

During the last 20-30 years many researchers have paid attention to the studies of properties of thewood polymer composites (WPC). A lot of works are closely related to investigations of exploitation properties of wood fibres or wood flour containing polyolefine composites [1, 2]. The most useful from wide selection of polyolefines are polypropylenes, but timber industry waste materials comprising lignocellulose fibres are often used as reinforcement of WPC [3-12]. Plywood industry is not an exception - part of waste materials (by-products) are used for heat energy, i.e. burned. In this work we have approbated reinforcing of polypropylene (PP) with one of the plywood industry by-products, such as birch plywood sawdust (PSWD),which containswood fibre fractions with different length [13]. The main fraction (50%) includes fibres with length l = 0.5 - 1 mm. Our previous study [13] has confirmed that PSWD is a promising filler for PP reinforcing. Addition of PSWD up to 40-50 wt.% has increased WPC tensile and flexural modulus, but decreased deformation ability of PP matrix, impact strength, water resistance and fluidity of composite melts. It was shown [13] that modification of the composites with interfacial modifier - coupling agent maleated polypropylene (MAPP content up to 5-7 wt.%) considerably improved all the abovementioned properties. SEM investigations also confirmed positive action of coupling agent on strengthening of adhesion interaction between components wood and PP matrix. Another way how to make better properties of the WPC is to form hybridcomposites [1, 14-24]. Very popular WPC modifiers are nanoparticle additions like organonanoclays, which increase WPC physical-mechanical properties - microhardness, water resistance and diminish barrier properties and combustibility [1, 2, 14-17, 19, 20]. The goal of this study was to investigate organonanoclays influence on plywood production industry by-product birch plywood sawdust (PSWD) containing

Effects of surface inactivation, high temperature drying and preservative treatment on surface roughness and colour of alder and beech wood

NASA Astrophysics Data System (ADS)

Aydin, Ismail; Colakoglu, Gursel

2005-10-01

Although extensive research has been conducted in wood surface quality analysis, a unified approach to surface quality characterisation does not exist. Measurements of the variation in surface roughness and surface colour are used widely for the evaluation of wood surface quality. Colour is a basic visual feature for wood and wood-based products. Colour measurement is one of the quality control tests that should be carried out because the colour deviations are spotted easily by the consumers. On the other hand, a common problem faced by plywood manufacturers is panel delamination, for which a major cause is poor quality glue-bonds resulting from rough veneer. Rotary cut veneers with dimensions of 500 mm × 500 mm × 2 mm manufactured from alder ( Alnus glutinosa subsp. barbata) and beech ( Fagus orientalis Lipsky) logs were used as materials in this study. Veneer sheets were oven-dried in a veneer dryer at 110 °C (normal drying temperature) and 180 °C (high drying temperature) after peeling process. The surfaces of some veneers were then exposed at indoor laboratory conditions to obtain inactive wood surfaces for glue bonds, and some veneers were treated with borax, boric acid and ammonium acetate solutions. After these treatments, surface roughness and colour measurements were made on veneer surfaces. High temperature drying process caused a darkening on the surfaces of alder and beech veneers. Total colour change value (Δ E*) increased linear with increasing exposure time. Among the treatment solutions, ammonium acetate caused the biggest colour change while treatment with borax caused the lowest changes in Δ E* values. Considerable changes in surface roughness after preservative treatment did not occur on veneer surfaces. Generally, no clear changes were obtained or the values mean roughness profile ( Ra) decreased slightly in Ra values after the natural inactivation process.

MUNICIPAL WASTE COMBUSTION ASSESSMENT: WASTE CO-FIRING

EPA Science Inventory

The report is an overview of waste co-firing and auxiliary fuel fired technology and identifies the extent to which co-firing and auxiliary fuel firing are practised. Waste co-firing is defined as the combustion of wastes (e. g., sewage sludge, medical waste, wood waste, and agri...

MUNICIPAL WASTE COMBUSTION ASSESSMENT: WASTE CO- FIRING

EPA Science Inventory

The report is an overview of waste co-firing and auxiliary fuel fired technology and identifies the extent to which co-firing and auxiliary fuel firing are practised. Waste co-firing is defined as the combustion of wastes (e. g., sewage sludge, medical waste, wood waste, and agri...

Physical and chemical evaluation of furniture waste briquettes.

PubMed

Moreno, Ana Isabel; Font, Rafael; Conesa, Juan A

2016-03-01

Furniture waste is mainly composed of wood and upholstery foam (mostly polyurethane foam). Both of these have a high calorific value, therefore, energy recovery would be an appropriate process to manage these wastes. Nevertheless, the drawback is that the energy content of these wastes is limited due to their low density mainly that of upholstery foam. Densification of separate foam presents difficulties due to its elastic character. The significance of this work lies in obtaining densified material by co-densification of furniture wood waste and polyurethane foam waste. Densification of furniture wood and the co-densification of furniture wood waste with polyurethane foam have been studied. On the one hand, the parameters that have an effect on the quality of the furniture waste briquettes have been analysed, i.e., moisture content, compaction pressure, presence of lignin, etc. The maximum weight percentage of polyurethane foam that can be added with furniture wood waste to obtain durable briquettes and the optimal moisture were determined. On the other hand, some parameters were analysed in order to evaluate the possible effect on the combustion. The chemical composition of waste wood was compared with untreated wood biomass; the higher nitrogen content and the concentration of some metals were the most important differences, with a significant difference of Ti content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pristine Early Eocene wood buried deeply in kimberlite from northern Canada.

PubMed

Wolfe, Alexander P; Csank, Adam Z; Reyes, Alberto V; McKellar, Ryan C; Tappert, Ralf; Muehlenbachs, Karlis

2012-01-01

We report exceptional preservation of fossil wood buried deeply in a kimberlite pipe that intruded northwestern Canada's Slave Province 53.3±0.6 million years ago (Ma), revealed during excavation of diamond source rock. The wood originated from forest surrounding the eruption zone and collapsed into the diatreme before resettling in volcaniclastic kimberlite to depths >300 m, where it was mummified in a sterile environment. Anatomy of the unpermineralized wood permits conclusive identification to the genus Metasequoia (Cupressaceae). The wood yields genuine cellulose and occluded amber, both of which have been characterized spectroscopically and isotopically. From cellulose δ(18)O and δ(2)H measurements, we infer that Early Eocene paleoclimates in the western Canadian subarctic were 12-17°C warmer and four times wetter than present. Canadian kimberlites offer Lagerstätte-quality preservation of wood from a region with limited alternate sources of paleobotanical information.

Groundwater Fate and Transport Modeling for Texarkana Wood Preserving Company Superfund Site, Texarkana, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnett, Ronald Chester

Fate and transport model results are presented for the Texarkana Wood Preserving Company (TWPC)superfund site. The conceptual model assumes two sources of contamination, specifically, the areas around the old and new process areas. Recent data show the presence of non-aqueous phase liquids (NAPL) in the aquifer that are also sources of dissolved contamination in the aquifer. A flow model was constructed and calibrated against measured hydraulic heads at permanent monitoring wells. Good matches were obtained between model simulated heads and most measured heads. An unexplained exception occurs at monitoring well MW-13 down gradient of the site beyond the measured contaminantmore » plume where the model predicts heads that are more than 2 ft. lower than reported field measurements. Adjusting hydraulic parameters in the model could not account for this anomaly and still preserve the head matches at other wells. There is likely a moderate deficiency in the conceptual model or perhaps a data error. Other information such as substantial amounts of infiltrating surface water in the area or a correction in surveyed elevation would improve the flow model. A particle tracking model calculated a travel time from the new process area to the Day’s Creek discharge location on the order of 40 years. Travel times from the old process area to Day’s Creek were calculated to be on the order of 80 years. While these calculations are subject to some uncertainty, travel times of decades are indicated.« less

STOCHASTIC HUMAN EXPOSURE AND DOSE SIMULATION MODEL FOR THE WOOD PRESERVATIVE SCENARIO (SHEDS-WOOD), VERSION 2 MODEL SAS CODE

EPA Science Inventory

Concerns have been raised regarding the safety of young children contacting arsenic and chromium residues while playing on and around Chromated Copper Arsenate (CCA) treated wood playground structures and decks. Although CCA registrants voluntarily canceled treated wood for resi...

Morphology, composition, and mixing state of primary particles from combustion sources - crop residue, wood, and solid waste.

PubMed

Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A P; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye; Li, Weijun

2017-07-11

Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combustion released OM and S-rich particles. Interestingly, particles from hardwood (pear wood and bamboo) and softwood (cypress and pine wood) combustion were mainly soot and OM in the flaming phase, respectively. The combustion of foam boxes, rubber tires, and plastic bottles/bags in the flaming phase released large amounts of soot internally mixed with a small amount of OM, whereas the combustion of printed circuit boards and copper-core cables emitted large amounts of OM with Br-rich inclusions. In addition, the printed circuit board combustion released toxic metals containing Pb, Zn, Sn, and Sb. The results are important to document properties of primary particles from combustion sources, which can be used to trace the sources of ambient particles and to know their potential impacts in human health and radiative forcing in the air.

RCRA, superfund and EPCRA hotline training module. Introduction to: Drip pads (40 cfr parts 264/265, subpart w) updated July 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-07-01

In 1990, EPA promulgated listings for wastes from wood preserving processes. Many of these wastes are generated by allowing preservative to drip from wood onto concrete pads, called drip pads. To facilitate proper handling of these wastes, EPA developed design and operating standards for drip pads used to manage hazardous wastes. This module explains these standards. It defines a drip pad and summarizes the design and operating standards for drip pads. It describes the relationship between generator accumulation provisions and drip pads.

Pristine Early Eocene Wood Buried Deeply in Kimberlite from Northern Canada

PubMed Central

Wolfe, Alexander P.; Csank, Adam Z.; Reyes, Alberto V.; McKellar, Ryan C.; Tappert, Ralf; Muehlenbachs, Karlis

2012-01-01

We report exceptional preservation of fossil wood buried deeply in a kimberlite pipe that intruded northwestern Canada’s Slave Province 53.3±0.6 million years ago (Ma), revealed during excavation of diamond source rock. The wood originated from forest surrounding the eruption zone and collapsed into the diatreme before resettling in volcaniclastic kimberlite to depths >300 m, where it was mummified in a sterile environment. Anatomy of the unpermineralized wood permits conclusive identification to the genus Metasequoia (Cupressaceae). The wood yields genuine cellulose and occluded amber, both of which have been characterized spectroscopically and isotopically. From cellulose δ18O and δ2H measurements, we infer that Early Eocene paleoclimates in the western Canadian subarctic were 12–17°C warmer and four times wetter than present. Canadian kimberlites offer Lagerstätte-quality preservation of wood from a region with limited alternate sources of paleobotanical information. PMID:23029080

Cone calorimeter tests of wood-based decking materials

Treesearch

Robert H. White; Mark A. Dietenberger; Nicole M. Stark

2007-01-01

New technologies in building materials have resulted in the use of a wide variety of materials in decks. As part of our effort to address fire concerns in the wildland-urban interface, the Forest Products Laboratory has been examining the fire performance of decking products. In addition to preservative-treated wood, decking products include wood-plastic composites and...

Comparison of methods for evaluating ground-contact copper preservative depletion

Treesearch

Stan Lebow; Steven Halverson

2008-01-01

Depletion of the biocide(s) used to treat wood has a major influence on service life and environmental concerns. However, little is known about the extent of depletion from the specific leaching method employed. Wood treated with two types of copper-based preservatives were leached using three different methods: field stakes (American Wood Protection Association (AWPA...

Formosan and native subterranean termite attack of pressure-treated SPF wood species exposed in Louisiana

Treesearch

Stan Lebow; Todd Shupe; Bessie Woodward; Douglas Crawford; Brian Via; Cherilyn Hatfield

2006-01-01

This study evaluated the relative ability of three types of wood preservatives to inhibit attack by Formosan subterranean termites (FST) (Coptotermes formosanus Shiraki) and native subterranean termites (Reticulitermes spp.). The study also evaluated the roles of preservative retention and penetration in preventing termite damage. Sections of boards from six wood...

The principles, procedures and pitfalls in identifying archaeological and historical wood samples

PubMed Central

Cartwright, Caroline R.

2015-01-01

Background The science of wood anatomy has evolved in recent decades to add archaeological and historical wood to its repertoire of documenting and characterizing modern and fossil woods. The increasing use of online wood anatomy databases and atlases has fostered the adoption of an international consensus regarding terminology, largely through the work of the International Association of Wood Anatomists (IAWA). Scope and Conclusions This review presents an overview for the general reader of the current state of principles and procedures involved in the study of the wood anatomy of archaeological and historical specimens, some of which may be preserved through charring, waterlogging, desiccation or mineral replacement. By means of selected case studies, the review evaluates to what extent varying preservation of wood anatomical characteristics limits the level of identification to taxon. It assesses the role played by increasingly accessible scanning electron microscopes and complex optical microscopes, and whether these, on the one hand, provide exceptional opportunities for high-quality imaging and analysis of difficult samples, but, on the other hand, might be misleading the novice into thinking that advanced technology can be a substitute for specialized botanical training in wood anatomy. PMID:25953039

Corrosion of metals in treated wood examined by synchrotron based xanes and XFM

Treesearch

Samuel L. Zelinka; Joseph E. Jakes; Grant T. Kirker; Leandro Passarini; Barry Lai

2016-01-01

Copper based waterborne wood preservatives are frequently used to extend the service life of wood products used in outdoor environments. While these copper based treatments protect the wood from fungal decay and insect attack, they increase the corrosion of metals embedded or in contact with the treated wood. Over the past ten years, several studies have looked at the...

Bond quality of phenol-based adhesives containing liquefied creosote-treated wood

Treesearch

Chung-Yun Hse; Feng Fu; Hui Pan

2009-01-01

Liquefaction of spent creosote-treated wood was studied to determine the technological practicability of its application in converting treated wood waste into resin adhesives. A total of 144 plywood panels were fabricated with experimental variables included 2 phenol to wood (P/W) ratios in liquefaction, 6 resin formulations (3 formaldehyde/liquefied wood (F/...

Wood and fish residuals composting in Alaska

Treesearch

David Nicholls; Thomas Richard; Jesse A. Micales

2002-01-01

The unique climates and industrial mix in southeast and south central Alaska are challenges being met by the region's organics recyclers. OMPOSTING wood residuals in Alaska has become increasingly important in recent years as wood processors and other industrial waste managers search for environmentally sound and profitable outlets. Traditionally, Alaska?s...

Preservation treatment for wood bridge application

Treesearch

Jake Bigelow; Stan Lebow; Carol A. Clausen; Lowell Greimann; Terry J. Wipf

2009-01-01

Timber can often be a cost-effective construction material for new bridges. The durability of the bridge greatly depends on proper attention to construction details and fabrication, as well as proper preservative treatment before, during, and after construction. Material repair and replacement costs for bridges are a considerable expense for highway agencies. To...

Monitoring of a landslide stabilized with bioengineering techniques in 1997, northern Tuscany. Vegetation development analysis and state of preservation of wood

NASA Astrophysics Data System (ADS)

Errico, Alessandro; Giambastiani, Yamuna; Guastini, Enrico; Dani, Andrea

2014-05-01

In 1996 a large landslide occurred in the chestnut grove nearby Pomezzana, a small town situated in the mountains of northern Tuscany, Italy. No damages were registered to population nor infrastructures, but the residual risks deriving from the effects of the event needed to be solved by means of a stabilization of the ground and reforestation. The choice has been found among bioengineering techniques, which perfectly fit in the ecosystem, landscape and the economic budgets of mountain engineering. A complex project has been implemented, using several different typologies of wooden structures, combined with rooted plants, wooden cuttings and grass seeding on the slopes. The most of the stabilization effect was assigned to the cribwalls, construct using local chestnut wood. Works ended in 1997. In 2013, 16 years later, a monitoring on the vegetation development and the state of preservation of the wood in cribwalls has been conducted. On vegetation, it has been surveyed the composition of species, diameter and height. Moreover, by means of a GPS device, the position of every plant has been registered and transcribed on GIS softwares for elaboration. The conservation of wood in cribwalls has been checked using a Resistograph, drilling each structure in three areas (at the two ends and roughly in the middle) and testing every order. The root systems of two plants have been excavated to calculate the RAR value for different depths, in order to quantify the contribution of roots in land stabilization. The soil has been also analyzed to determine structure, texture and geotechnical properties. Combining these data with the topographic survey conducted by the designers of the work, it has been possible to calculate the Safety Factor for landslide triggering using the model Slip4ex. The results show a good preservation rate of wooden structures, combined with a high contribution of roots in stabilization. The registered tree species (mainly Alnus glutinosa) were almost all

Preferential soft-tissue preservation in the Hot Creek carbonate spring deposit, British Columbia, Canada

NASA Astrophysics Data System (ADS)

Rainey, Dustin K.; Jones, Brian

2010-05-01

The relict Holocene Hot Creek carbonate spring deposit in southeast British Columbia is characterized by excellent preservation of soft-tissue organisms (e.g. cyanobacteria), but poor preservation of organisms with hard-tissue (e.g. wood, diatoms). The deposit is formed mainly of calcified cyanobacteria, with fewer mineralized macrophytes (plants), bryophytes (mosses), wood, and diatoms. Cyanobacteria grew as solitary filaments ( Lyngbya) and as radiating hemispherical colonies ( Rivularia). Both were preserved by encrustation and encapsulation while alive, and as casts after filament death and decay. Sheath impregnation was rare to absent. Filament encrustation, whereby calcite crystals nucleated on, and grew away from the sheath exterior, produced moulds that replicated external filament morphology, but hastened filament decay. Filament encapsulation, whereby calcite nucleated in the vicinity of, and grew towards the encapsulated filament, promoted sheath preservation even after trichome decay. Subsequent calcite precipitation inside the hollow sheath generated sheath casts. The inability of mineralizing spring water to penetrate durable cell walls meant that bryophytes, macrophytes, and most wood was preserved by encrustation. Some wood resisted complete decay for several thousand years, and its lignified cell walls allowed rare permineralizations. Diatoms were not preserved in the relict deposit because the frustules were dissolved by the basic spring water. Amorphous calcium carbonate produced by photosynthetic CO 2 removal may have acted as nucleation sites for physicochemically precipitated calcite. Thus, metabolic activities of floral organisms probably initiated biotic mineralization, but continuous inorganic calcite precipitation on and in flora ensured that soft tissues were preserved.

Chemical remediation of wood treated with micronised, nano or soluble copper preservatives

Treesearch

Saip Nami Kartal; Evren Terzi; Bessie Woodward; Carol A. Clausen; Stan T. Lebow

2013-01-01

The potential for extraction of copper from wood treated with micronised, nano or soluble forms of copper has been evaluated in view of chemical remediation. In focus were EDTA, oxalic acid, bioxalate, and D-gluconic acid for extraction of Cu from treated wood. Bioxalate extractions for 24 h resulted in Cu removal over 95% for all tested...

LEACHING OF CCA-TREATED WOOD: IMPLICATIONS FOR WASTE DISPOSAL

EPA Science Inventory

Leaching of arsenic, chromium, and copper from chromated copper arsenate (CCA)-treated wood poses possible environmental risk when disposed. Samples of un-weathered CCA-treated wood were tested using a variety of US regulatory leaching procedures, including the toxicity character...

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Code of Federal Regulations, 2013 CFR

2013-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not..., 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3065 What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Code of Federal Regulations, 2012 CFR

2012-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not..., 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3065 What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Code of Federal Regulations, 2014 CFR

2014-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not..., 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3065 What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Code of Federal Regulations, 2010 CFR

2010-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not..., 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3065 What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Code of Federal Regulations, 2011 CFR

2011-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not..., 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3065 What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Effects of herbicide (Round-up®) on Alliaria petiolata (Bieb.) Cavara & Grande (garlic mustard), an invasive biennial, and subsequent effects on the native plant community in Hueston Woods State Nature Preserve, Ohio

Treesearch

Adriane M. Carlson; David L. Gorchov

2003-01-01

Alliaria petiolata (Garlic Mustard) is invasive throughout the northeast U.S. and has become established in the Nature Preserve at Hueston Woods State Park in southwest Ohio. The Park is attempting eradication by spot-spraying Round-up® herbicide each fall.

Chemical characterisation of the whole plant cell wall of archaeological wood: an integrated approach.

PubMed

Zoia, Luca; Tamburini, Diego; Orlandi, Marco; Łucejko, Jeannette Jacqueline; Salanti, Anika; Tolppa, Eeva-Liisa; Modugno, Francesca; Colombini, Maria Perla

2017-07-01

Wood artefacts undergo complex alteration and degradation during ageing, and gaining information on the chemical composition of wood in archaeological artefacts is fundamental to plan conservation strategies. In this work, an integrated analytical approach based on innovative NMR spectroscopy procedures, gel permeation chromatography and analytical pyrolysis coupled with gas chromatography/mass spectrometry (Py-GC-MS) was applied for the first time on archaeological wood from the Oseberg collection (Norway), in order to evaluate the chemical state of preservation of the wood components, without separating them. We adopted ionic liquids (ILs) as non-derivatising solvents, thus obtaining an efficient dissolution of the wood, allowing us to overcome the difficulty of dissolving wood in its native form in conventional molecular solvents. Highly substituted lignocellulosic esters were therefore obtained under mild conditions by reacting the solubilised wood with either acetyl chloride or benzoyl chloride. A phosphytilation reaction was also performed using 2-chloro-4,4,5,5-tetramethyl-1,3,2-dioxaphospholan. As a result, the functionalised wood developed an enhanced solubility in molecular solvents, thus enabling information about modifications of lignin, depolymerisation of cellulose and structure of lignin-carbohydrate complexes to be obtained by means of spectroscopic (2D-HSQC-NMR and 31 P-NMR) and chromatographic (gel permeation chromatography) techniques. Py-GC-MS was used to investigate the degradation undergone by the lignocellulosic components on the basis of their pyrolysis products, without any pre-treatment of the samples. The application of all these combined techniques enabled a comprehensive characterisation of the whole cell wall of archaeological wood and the evaluation of its state of preservation. High depletion of carbohydrates and high extent of lignin oxidation were highlighted in the alum-treated objects, whereas a good preservation state was found

Extending service life of timber bridges with preservatives

Treesearch

James P. Wacker; Douglas M. Crawford

2003-01-01

Treated timber bridges have been widely used for railroad and highway bridges throughout the United States during the 20th century. However, improvements in preservative technology are needed as a result of changing environmental views and public perceptions concerning the use of preservative treated wood in aquatic environments. Within the past 15 years, three...

Estimating preservative release from treated wood exposed to precipitation

Treesearch

Stan Lebow; Patricia Lebow; Daniel Foster

2008-01-01

Accelerated leaching methods are needed to better estimate emissions from treated wood used above ground or above water. In this study, we evaluated leaching methods using continuous immersion, dip immersion, and simulated rainfall approaches. Copper and/or boron emissions were measured for specimens treated with either chromated copper arsenate Type C (CCA-C) or a...

Assessment of chemical and material contamination in waste wood fuels--A case study ranging over nine years.

PubMed

Edo, Mar; Björn, Erik; Persson, Per-Erik; Jansson, Stina

2016-03-01

The increased demand for waste wood (WW) as fuel in Swedish co-combustion facilities during the last years has increased the import of this material. Each country has different laws governing the use of chemicals and therefore the composition of the fuel will likely change when combining WW from different origins. To cope with this, enhanced knowledge is needed on WW composition and the performance of pre-treatment techniques for reduction of its contaminants. In this study, the chemical and physical characteristics of 500 WW samples collected at a co-combustion facility in Sweden between 2004 and 2013 were investigated to determine the variation of contaminant content over time. Multivariate data analysis was used for the interpretation of the data. The concentrations of all the studied contaminants varied widely between sampling occasions, demonstrating the highly variable composition of WW fuels. The efficiency of sieving as a pre-treatment measure to reduce the levels of contaminants was not sufficient, revealing that sieving should be used in combination with other pre-treatment methods. The results from this case study provide knowledge on waste wood composition that may benefit its management. This knowledge can be applied for selection of the most suitable pre-treatments to obtain high quality sustainable WW fuels. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Influence of biochars, compost and iron grit, alone and in combination, on copper solubility and phytotoxicity in a Cu-contaminated soil from a wood preservation site.

PubMed

Oustriere, Nadège; Marchand, Lilian; Galland, William; Gabbon, Lunel; Lottier, Nathalie; Motelica, Mikael; Mench, Michel

2016-10-01

Two biochars, a green waste compost and iron grit were used, alone and in combination, as amendment to improve soil properties and in situ stabilize Cu in a contaminated soil (964mgCukg(-1)) from a wood preservation site. The pot experiment consisted in 9 soil treatments (% w/w): untreated Cu-contaminated soil (Unt); Unt soil amended respectively with compost (5%, C), iron grit (1%, Z), pine bark-derived biochar (1%, PB), poultry-manure-derived biochar (1%, AB), PB or AB+C (5%, PBC and ABC), and PB or AB+Z (1%, PBZ and ABZ). After a 3-month reaction period, the soil pore water (SPW) was sampled in potted soils and dwarf beans were grown for a 2-week period. In the SPW, all amendments decreased the Cu(2+) concentration, but total Cu concentration increased in all AB-amended soils due to high dissolved organic matter (DOM) concentration. No treatment improved root and shoot DW yields, which even decreased in the ABC and ABZ treatments. The PBZ treatment decreased total Cu concentration in the SPW while reducing the gap with common values for root and shoot yields of dwarf bean plants. A field trial is underway before any recommendation for the PB-based treatments. Copyright © 2016 Elsevier B.V. All rights reserved.

Chemical modification : a non-toxic approach to wood preservation

Treesearch

Roger M. Rowell

2006-01-01

Wood can be chemically modified to reduce the moisture content of the cell wall and increases decay resistance. As the level of bonded chemical increases, the cell wall equilibrium moisture content decreases and the resistance to attack by white-and brown-rot fungi increases. There is a direct relationship between the decrease in cell wall moisture Content and...

Removal of arsenic from toxic ash after combustion of impregnated wood

NASA Astrophysics Data System (ADS)

Ottosen, L. M.; Pedersen, A. J.; Kristensen, I. V.; Ribeiro, A. B.

2003-05-01

ln the next ten years the amounts of waste wood impregnated with Cu, Cr and As (CCA) is expected to increase dramatically. Mixed with municipal solid waste for incineration the wood constitutes a problem because As emission is not hindered through common flue gas treatment. Furthermore the ashes will contain higher concentrations of Cu, Cr and As. In different countries initiatives has been taken or are implemented to sort the impregnated wood from other waste and handle the wood separately. This handling can involve combustion in special plants. This paper deals with electrodialytic treatment of ash from combustion of CCA treated wood. The total concentrations in the ash were very high: 69gCu/kg, 62gCr/kg and 35gAs/kg. A SEM/EDX analysis showed that Cr was mainly build into the matrix structure of the ash. Cu, too, but some Cu was also precipitated on the surface of the particles. As, on the other hand, was only found associated with Ca and thus probably in a soluble form. As is the main problem of the ash due to the high toxicity and mobility and thus the treatment aims at removing this element. It was shown that during 5 days of electrodialytic treatment 92% As could be removed.

Moisture Sorption, Biological Durability, and Mechanical Performance of WPC Containing Modified Wood and Polylactates

Treesearch

B. Kristoffer Segerholm; Rebecca E. Ibach; Mats Westin

2012-01-01

Biological durability is an important feature for wood-plastic composites (WPC) intended for outdoor applications. One route to achieving WPC products with increased biological durability is to use wood preservative agents in the formulation of the WPC. Another option could be to use a chemically modified wood component that already exhibits increased resistance to...

Performance and thermal behavior of wood plastic composite produced by nonmetals of pulverized waste printed circuit boards.

PubMed

Guo, Jie; Tang, Yinen; Xu, Zhenming

2010-07-15

A new kind of wood plastic composite (WPC) was produced by compounding nonmetals from waste printed circuit boards (PCBs), recycled high-density polyethylene (HDPE), wood flour and other additives. The blended granules were then extruded to profile WPC products by a conical counter-rotating twin-screw extruder. The results showed that the addition of nonmetals in WPC improved the flexural strength and tensile strength and reduced screw withdrawal strength. When the added content of nonmetals was 40%, the flexural strength of WPC was 23.4 MPa, tensile strength was 9.6 MPa, impact strength was 3.03 J/m(2) and screw withdrawal strength was 1755 N. Dimensional stability and fourier transform infrared spectroscopy (FTIR) of WPC panels were also investigated. Furthermore, thermogravimetric analysis showed that thermal degradation of WPC mainly included two steps. The first step was the decomposition of wood flour and nonmetals from 260 to 380 degrees C, and the second step was the decomposition of HDPE from 440 to 500 degrees C. The performance and thermal behavior of WPC produced by nonmetals from PCBs achieves the standard of WPC. It offers a novel method to treat nonmetals from PCBs. 2010 Elsevier B.V. All rights reserved.

From laboratory corrosion tests to a corrosion lifetime for wood fasteners : progress and challenges

Treesearch

Samuel L. Zelinka; Dominique Derome; Samuel V. Glass

2010-01-01

Determining a “corrosion-lifetime” for fasteners embedded in wood treated with recently adopted preservative systems depends upon successfully relating results of laboratory tests to in-service conditions. In contrast to laboratory tests where metal is embedded in wood at constant temperature and moisture content, the in-service temperature and moisture content of wood...

Physical and chemical characterization of waste wood derived biochars.

PubMed

Yargicoglu, Erin N; Sadasivam, Bala Yamini; Reddy, Krishna R; Spokas, Kurt

2015-02-01

Biochar, a solid byproduct generated during waste biomass pyrolysis or gasification in the absence (or near-absence) of oxygen, has recently garnered interest for both agricultural and environmental management purposes owing to its unique physicochemical properties. Favorable properties of biochar include its high surface area and porosity, and ability to adsorb a variety of compounds, including nutrients, organic contaminants, and some gases. Physical and chemical properties of biochars are dictated by the feedstock and production processes (pyrolysis or gasification temperature, conversion technology and pre- and post-treatment processes, if any), which vary widely across commercially produced biochars. In this study, several commercially available biochars derived from waste wood are characterized for physical and chemical properties that can signify their relevant environmental applications. Parameters characterized include: physical properties (particle size distribution, specific gravity, density, porosity, surface area), hydraulic properties (hydraulic conductivity and water holding capacity), and chemical and electrochemical properties (organic matter and organic carbon contents, pH, oxidation-reduction potential and electrical conductivity, zeta potential, carbon, nitrogen and hydrogen (CHN) elemental composition, polycyclic aromatic hydrocarbons (PAHs), heavy metals, and leachable PAHs and heavy metals). A wide range of fixed carbon (0-47.8%), volatile matter (28-74.1%), and ash contents (1.5-65.7%) were observed among tested biochars. A high variability in surface area (0.1-155.1g/m(2)) and PAH and heavy metal contents of the solid phase among commercially available biochars was also observed (0.7-83 mg kg(-1)), underscoring the importance of pre-screening biochars prior to application. Production conditions appear to dictate PAH content--with the highest PAHs observed in biochar produced via fast pyrolysis and lowest among the gasification

The use of a paper/wood/plastics mixing as a model waste to study the incineration of municipal solid waste in fluidized beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desroches-Ducarne, E.; Marty, E.; Martin, G.

1997-12-31

Municipal Solid Waste (MSW) incineration in fluidized beds has recently become the subject of intense research. In this paper, the authors chose to elaborate a simple model waste prepared with 4 of the main MSW components (paper, wood, PE, and PVC). The behaviors of typical French MSW and model waste during their combustion in a fluidized bed incinerator were studied. To establish the comparison, the emissions of NO, N{sub 2}O, SO{sub 2} and HCl were investigated. Moreover, experiments were performed according to statistical experimental designs to examine the effect of various operating parameters including bed temperature, excess air, limestone feedingmore » rate and waste moisture. On a qualitative point of view, the impact of the combustion conditions on the pollutants emissions was found to be the same for the two wastes. Bed temperature and excess air have, in both cases, an important impact on NO and N{sub 2}O emissions. Nitrogen oxides production was also directly related to limestone feed content. Very high sulphur and chlorine retention was obtained when limestone was added at much larger excess to the feed. N{sub 2}O emissions are less important during the model waste combustion. The nitrogen functionality seems to give rise to such a phenomenon. In MSW, nitrogen is included in high molecules which is released for a great part as HCN or remains in char, which are the main sources of N{sub 2}O. To confirm this assumption, tests for measuring the HCN/NH{sub 3} ratio for each fuel were performed.« less

Dilute phosphoric acid-catalysed hydrolysis of municipal bio-waste wood shavings using autoclave parr reactor system.

PubMed

Orozco, Angela M; Al-Muhtaseb, Ala'a H; Albadarin, Ahmad B; Rooney, David; Walker, Gavin M; Ahmad, Mohammad N M

2011-10-01

The visibility of using municipal bio-waste, wood shavings, as a potential feedstock for ethanol production was investigated. Dilute acid hydrolysis of wood shavings with H₃PO₄ was undertaken in autoclave parr reactor. A combined severity factor (CSF) was used to integrate the effects of hydrolysis times, temperature and acid concentration into a single variable. Xylose concentration reached a maximum value of 17 g/100 g dry mass corresponding to a yield of 100% at the best identified conditions of 2.5 wt.% H₃PO₄, 175 °C and 10 min reaction time corresponding to a CSF of 1.9. However, for glucose, an average yield of 30% was obtained at 5 wt.% H₃PO₄, 200 °C and 10 min. Xylose production increased with increasing temperature and acid concentration, but its transformation to the degradation product furfural was also catalysed by those factors. The maximum furfural formed was 3 g/100 g dry mass, corresponding to the 24% yield. Copyright © 2011 Elsevier Ltd. All rights reserved.

Assessing Potential Acidification of Marine Archaeological Wood Based on Concentration of Sulfur Species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The presence of sulfur in marine archaeological wood presents a challenge to conservation. Upon exposure to oxygen, sulfur compounds in waterlogged wooden artifacts are being oxidized, producing sulfuric acid. This speeds the degradation of the wood, potentially damaging specimens beyond repair. Sulfur K-edge x-ray absorption spectroscopy was used to identify the species of sulfur present in samples from the timbers of the Mary Rose, a preserved 16th century warship known to undergo degradation through acidification. The results presented here show that sulfur content varied significantly on a local scale. Only certain species of sulfur have the potential to produce sulfuricmore » acid by contact with oxygen and seawater in situ, such as iron sulfides and elemental sulfur. Organic sulfurs, such as the amino acids cysteine and methionine, may produce acid but are integral parts of the wood's structure and may not be released from the organic matrix. The sulfur species contained in the sample reflect the exposure to oxygen while submerged, and this exposure can differ greatly over time and position. A better understanding of the species pathway to acidifications required, along with its location, in order to suggest a more customized and effective preservation strategy. Waterlogged archaeological wood, frequently in the form of shipwrecks, is being excavated for historical purposes in many countries around the world. Even after extensive efforts towards preservation, scientists are discovering that accumulation of sulfate salts results in acidic conditions on the surfaces of the artifacts. Sulfuric acid degrades structural fibers in the wood by acid hydrolysis of cellulose, accelerating the decomposition of the ship timbers. Determining the sulfur content of waterlogged wood is now of great importance in maritime archaeology. Artifact preservation is often more time consuming and expensive than the original excavation; but it is key to the availability of objects

Effects of humidity on the magnetic and woody characteristics of powder-type magnetic wood

NASA Astrophysics Data System (ADS)

Oka, H.; Tokuta, H.; Namizaki, Y.; Sekino, N.

2004-05-01

Among three types of proposed magnetic wood, powder-type magnetic wood can be made of recycled magnetic materials from IT devices, consumer electronics and waste wood. Because of its wood powder content, powder-type magnetic wood shows special characteristics different from those of typical magnetic materials. We focused on the relationship between humidity and magnetic characteristics of powder-type magnetic wood. The magnetic powder ratio, wood powder density and magnetic binder density were all examined as parameters for AC permeability.

Consumer willingness to pay for a naturally decay-resistant wood product.

Treesearch

Geoffrey Donovan; Hayley Hesseln

2004-01-01

Chromated copper arsenate (CCA) is the most widely used chemical wood preservative in the United States. Concerns about the safety of CCA led to an agreement between the Environmental Protection Agency and the wood treatment industry to withdraw CCA for nonindustrial uses by the end of 2003. In light of the publicity surrounding the withdrawal of CCA, this article...

Evidence of cellulose digestion in the wood boring isopod Sphaeroma terebrans

Treesearch

Lori K. Benson; Stanley A. Rice; Bruce R. Johnson

1999-01-01

Sphaeroma terebrans Bate is a widespread estuarine, wood-boring, isopod found in red mangrove (Rhizophora mangle) forests of tropical and subtropical estuarine waters. Because it causes extensive damage to man-made structures in marine coastal zones and is resistant to common methods of wood preservation it is important to understand fully how S. terebrans uses the...

Role of construction debris in release of copper, chromium, and arsenic from treated wood structures

Treesearch

Stan T. Lebow; Steven A. Halverson; Jeffrey J. Morrell; John Simonsen

Recent research on the release of wood preservatives from treated wood used in sensitive environments has not considered the potential contribution from construction residues. This study sought to develop leaching rate data for small construction debris and compare those to the release rate from treated wood itself. Western hemlock boards were pressure treated with...

Development of naphthenic acid fractionation with supercritical fluid extraction for use in wood decay testing

Treesearch

Brett Niemi; Wayne St. John; Bessie Woodward; Rodney DeGroot; Gary McGinnis

2000-01-01

In recent years, the performance of copper naphthenate as a wood preservative has been in question. To understand the varying results of copper naphthenate in preventing wood decay, a closer look at eight naphthenic acid (NA) supplies was undertaken. Initial studies of NA samples from individual suppliers revealed large differences in chemical composition and wood...

Protection of Wood from Microorganisms by Laccase-Catalyzed Iodination

PubMed Central

Engel, J.; Thöny-Meyer, L.; Schwarze, F. W. M. R.; Ihssen, J.

2012-01-01

In the present work, Norway spruce wood (Picea abies L.) was reacted with a commercial Trametes versicolor laccase in the presence of potassium iodide salt or the phenolic compounds thymol and isoeugenol to impart an antimicrobial property to the wood surface. In order to assess the efficacy of the wood treatment, a leaching of the iodinated and polymerized wood and two biotests including bacteria, a yeast, blue stain fungi, and wood decay fungi were performed. After laccase-catalyzed oxidation of the phenols, the antimicrobial effect was significantly reduced. In contrast, the enzymatic oxidation of iodide (I−) to iodine (I2) in the presence of wood led to an enhanced resistance of the wood surface against all microorganisms, even after exposure to leaching. The efficiency of the enzymatic wood iodination was comparable to that of a chemical wood preservative, VP 7/260a. The modification of the lignocellulose by the laccase-catalyzed iodination was assessed by the Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) technique. The intensities of the selected lignin-associated bands and carbohydrate reference bands were analyzed, and the results indicated a structural change in the lignin matrix. The results suggest that the laccase-catalyzed iodination of the wood surface presents an efficient and ecofriendly method for wood protection. PMID:22865075

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler.

PubMed

Samaras, P; Skodras, G; Sakellaropoulos, G P; Blumenstock, M; Schramm, K W; Kettrup, A

2001-01-01

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.

FIELD-SCALE LEACHING OF ARSENIC, CHROMIUM AND COPPER FROM WEATHERED TREATED WOOD

PubMed Central

Hasan, A. Rasem; Hu, Ligang; Solo-Gabriele, Helena M.; Fieber, Lynne; Cai, Yong; Townsend, Timothy G.

2010-01-01

Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m2. Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m3), medium (4.8 kg/m3) and high (35.4 kg/m3) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m3 as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (<40 mg) in all CCA treated wood samples. Copper leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals’ leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers. PMID:20053493

Wood surface modification by in-situ sol-gel deposition of hybrid inorganic-organic thin films

Treesearch

Mandla A. Tshabalala; Li-Piin Sung

2007-01-01

Interest in the use of nanoparticles of iron, titanium, aluminum, and zinc oxides in transparent coatings for wood is increasing. Such nano-composite coatings have the potential of not only preserving the natural color of the wood, but also stabilizing the wood surface against the combined degradative effects of sunlight and moisture. The nanoparticles can be used as...

Evaluating the natural durability of native and tropical wood species against Reticulitermes flavipes

Treesearch

R.A. Arango; F. Green; K. Hintz; R.B. Miller

2004-01-01

Environmental pressures to eliminate arsenate from wood preservatives has resulted in voluntary removal of CCA for residential applications in the United States. A new generation of copper organic preservatives has been formulated to replace CCA for decking and in-ground applications but there is no guarantee that these preservatives represent a permanent solution to...

Lifecycle Assessment of Biofuel Production from Wood Pyrolysis Technology

ERIC Educational Resources Information Center

Manyele, S. V.

2007-01-01

Due to a stronger dependency on biomass for energy, there is a need for improved technologies in biomass-to-energy conversion in Tanzania. This paper presents a life cycle assessment (LCA) of pyrolysis technology used for conversion of wood and wood waste to liquid biofuel. In particular, a survey of environmental impacts of the process is…

Mechanical Properties of Longleaf Pine Treated with Waterborne Salt Preservatives.

DTIC Science & Technology

1983-08-01

were measured on small clear bending specimens of longleaf pine sapwood treated with three wateroorne salt preservative systems. Preservative...wood, but the results of past research in this area (appendix I: Literature) are inconsistent and inconclusive, particularly at high loadings of...pine sapwood either air or kiln dried after treatment to retentions from 0.25 to 2.5 lb/ft3. ACA has no effect on MOR. but CCA-type preservatives

Synthesis of wood treatment alternatives for timber railroad structures.

DOT National Transportation Integrated Search

2011-12-01

A wealth of information exists on various wood preservatives, treatment techniques, curing practices, and other engineered : controls, along with alternative materials for replacement. This study was initiated to review and synthesize available : inf...

U.S. Geological Survey program on toxic waste--ground-water contamination; proceedings of the Third technical meeting, Pensacola, Florida, March 23-27, 1987

USGS Publications Warehouse

Franks, Bernard J.

1987-01-01

Because of the widespread distribution of creosote in the environment, an abandoned wood-treatment plant in Pensacola, Fla., was selected by the U.S. Geological Survey Office of Hazardous Waste Hydrology as one of three national research demonstration areas in order to increase our understanding of hydrologic processes affecting the distributions of contaminants in ground water. The site was selected because of its long, uninterrupted history (1902 81) of discharging wastewaters to unlined surface impoundments, availability of a preliminary data base (Troutman and others, 1984), and the high probability of useful technology transfer from an investigation of the fate of organic compounds associated with wood-preserving wastewaters in the subsurface environment.

Optically Transparent Wood from a Nanoporous Cellulosic Template: Combining Functional and Structural Performance.

PubMed

Li, Yuanyuan; Fu, Qiliang; Yu, Shun; Yan, Min; Berglund, Lars

2016-04-11

Optically transparent wood (TW) with transmittance as high as 85% and haze of 71% was obtained using a delignified nanoporous wood template. The template was prepared by removing the light-absorbing lignin component, creating nanoporosity in the wood cell wall. Transparent wood was prepared by successful impregnation of lumen and the nanoscale cellulose fiber network in the cell wall with refractive-index-matched prepolymerized methyl methacrylate (MMA). During the process, the hierarchical wood structure was preserved. Optical properties of TW are tunable by changing the cellulose volume fraction. The synergy between wood and PMMA was observed for mechanical properties. Lightweight and strong transparent wood is a potential candidate for lightweight low-cost, light-transmitting buildings and transparent solar cell windows.

Blood Preservation Study.

DTIC Science & Technology

1983-10-01

red cells during storage. We discovered that periodic mixing during storage increases the levels of 2,3- diphosphoglycerate , and probably as a...214. 21. Wood, L.A. and Beutler, E. 1973. The effect of periodic mixing on the preservation of 2,3- diphosphoglycerate (2,3- dpg) levels in stored blood...determine the rate of depletion of 2,3- diphosphoglycerate from stored red cells, to determine the effect of different storage conditions on the rate

Natural durability of tropical and native woods against termite damage by Reticulitermes flavipes (Kollar)

Treesearch

Rachel A. Arango; Frederick Green; Kristina Hintz; Patricia K. Lebow; Regis B. Miller

2006-01-01

Environmental pressure has resulted in voluntary removal of chromated copper arsenate (CCA) from wood preservatives in residential applications in the United States. A new generation of copper organic preservatives was formulated as replacements, but these preservatives may not provide a permanent solution to all related problems. Some of these issues include concern...

Exploring the role of wood waste landfills in early detection of non-native alien wood-boring beetles

Treesearch

Davide Rassati; Massimo Faccoli; Lorenzo Marini; Robert A. Haack; Andrea Battisti; Edoardo Petrucco Toffolo

2015-01-01

Non-native wood-boring beetles (Coleoptera) represent one of the most commonly intercepted groups of insects at ports worldwide. The development of early detection methods is a crucial step when implementing rapid response programs so that non-native wood-boring beetles can be quickly detected and a timely action plan can be produced. However, due to the limited...

RELATIVE LEACHING AND AQUATIC TOXICITY OF PRESSURE-TREATED WOOD PRODUCTS USING BATCH LEACHING TESTS

EPA Science Inventory

Samples of southern yellow pine dimensional lumber, each treated with one of five different waterborne chemical preservatives, were leached using 18-hour batch leaching tests. The wood preservatives included chromated copper arsenate (CCA), alkaline copper quaternary (ACQ), coppe...

Shell-armored wood cobbles as a potential criterion for detrital coal deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiMarco, M.J.; Nummedal, D.

1986-01-01

Shell-armored wood cobbles occur on detrital-peat beaches along the seaward edge of the Mississippi Delta. Shell material consists exclusively of Mulinia lateralis, a dwarf surf clam. Soft, heavy, waterlogged wood fragments are abraded and become armored by hard shells in response to wave activity on the beach. Although their preservation potential is suspect, fossilized shell-armored wood clasts would probably be recognized as a type of coal ball and might indicate an allochthonous origin for the host coal.

Quaternized wood as sorbent for hexavalent chromium.

PubMed

Low, K S; Lee, C K; Lee, C Y

2001-01-01

The potential of quaternized wood (QW) chips in removing hexavalent chromium from synthetic solution and chrome waste under both batch and continuous-flow conditions was investigated. Sorption was found to be dependent on pH, metal concentration, and temperature. QW chips provide higher sorption capacity and wider pH range compared with untreated wood chips. The equilibrium data could be fitted into the Langmuir isotherm model, and maximum sorption capacities were calculated to be 27.03 and 25.77 mg/g in synthetic chromate solution and chrome waste, respectively. The presence of sulfate in high concentration appeared to suppress the uptake of chromium by QW chips. Column studies showed that bed depth influenced the breakthrough time greatly whereas flow rate of influent had little effect on its sorption on the column.

Long-term soil accumulation of chromium, copper, and arsenic adjacent to preservative-treated wood.

Treesearch

S. Lebow; D. Foster; J. Evans

2004-01-01

Chromated copper arsenate (CCA) treated wood has been used extensively in outdoor applications. The Environmental Protection Agency (EPA) and CCA producers recently reached an agreement to limit future use of CCA for some types of applications. One area of concern is the long-term accumulation of leached CCA in soil adjacent to treated wood structures. Interpreting...

Generation and Recovery of Solid Wood Waste in the U.S.

Treesearch

Bob Falk; David McKeever

2012-01-01

North America has a vast system of hardwood and softwood forests, and the wood harvested from this resource is widely used in many applications. These include lumber and other building materials, furniture, crating, containers, pallets and other consumer goods. This wide array of wood products generates not only a large amount of industrial wood by-product during the...

Synchrotron based x-ray fluorescence microscopy confirms copper in the corrosion products of metals in contact with treated wood

Treesearch

Samuel L. Zelinka; Joseph E. Jakes; Grant T. Kirker; David Vine; Stefan Vogt

2017-01-01

Copper based waterborne wood preservatives are frequently used to extend the service life of wood products when subjected to frequent moisture exposure. While these copper based treatments protect the wood from fungal decay and insect attack, they increase the corrosion of metals embedded or in contact with the treated wood. Previous research has shown the most...

In vitro bioaccessibility of copper azole following simulated dermal transfer from pressure-treated wood

EPA Science Inventory

Micronized copper azole (MCA) and micronized copper quaternary are the latest wood preservatives to replace the liquid lkaline copper and chromated copper arsenate preservatives due to concerns over the toxicity or lack of effectiveness of the earlier formulations. Today, the use...

On the patterns and processes of wood in northern California streams

NASA Astrophysics Data System (ADS)

Benda, Lee; Bigelow, Paul

2014-03-01

Forest management and stream habitat can be improved by clarifying the primary riparian and geomorphic controls on streams. To this end, we evaluated the recruitment, storage, transport, and the function of wood in 95 km of streams (most drainage areas < 30 km2) in northern California, crossing four coastal to inland regions with different histories of forest management (managed, less-managed, unmanaged). The dominant source of variability in stream wood storage and recruitment is driven by local variation in rates of bank erosion, forest mortality, and mass wasting. These processes are controlled by changes in watershed structure, including the location of canyons, floodplains and tributary confluences; types of geology and topography; and forest types and management history. Average wood storage volumes in coastal streams are 5 to 20 times greater than inland sites primarily from higher riparian forest biomass and growth rates (productivity), with some influence by longer residence time of wood in streams and more wood from landsliding and logging sources. Wood recruitment by mortality (windthrow, disease, senescence) was substantial across all sites (mean 50%) followed by bank erosion (43%) and more locally by mass wasting (7%). The distances to sources of stream wood are controlled by recruitment process and tree height. Ninety percent of wood recruitment occurs within 10 to 35 m of channels in managed and less-managed forests and upward of 50 m in unmanaged Sequoia and coast redwood forests. Local landsliding extends the source distance. The recruitment of large wood pieces that create jams (mean diameter 0.7 m) is primarily by bank erosion in managed forests and by mortality in unmanaged forests. Formation of pools by wood is more frequent in streams with low stream power, indicating the further relevance of environmental context and watershed structure. Forest management influences stream wood dynamics, where smaller trees in managed forests often generate

Wood chips for fuel and energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-01-01

A separate abstract was prepared for each of 13 individual presentations. Included in the appendices is: (1) a reprint from the journal Pulp and Paper, June 1978, by Larry Burkholder entitled, Wholetree Chipping Provides an Answer to Multiple Wood Fiber Use; and (2) a pictorial and graphical description of the York-Shipley (York, PA) Fluid Flame Solid Wastes Converter and list of installations using the converter. Also inluded as appendices are: (a) literature available on energy from biomass; (b) Canadian Government sources of information on use of biomass energy for industrial purposes; (c) list of New York State Dept. of Environmentalmore » Conservation Directors and Regional Foresters; (d) Northeast wood-fired boiler consulting firms; (e) list of suppliers of wood and wood residues as an energy source; (f) list of manufacturers of combustion and heat-recovery systems; (g) list of manufacturers of pollution control and monitoring equipment; and (h) potential sources of financing for energy-related projects in New York.« less

Blood Preservation Study.

DTIC Science & Technology

1983-01-01

1977. 3. Wood LA and Beutler E: The effect of periodic mixing on the preservation of 2,3- diphosphoglycerate (2,3-DPG) levels in stored blood. Blood 42:17...ATP levels and the viability of red cells was investigated; and several procedures for protein extraction from red cells were performed. DO 1473... levels are a disappointing parameter with respect to predicting the viability of stored red cells (5-8). There is a great need to identify measurements

Evaluation of waste mushroom logs as a potential biomass resource for the production of bioethanol.

PubMed

Lee, Jae-Won; Koo, Bon-Wook; Choi, Joon-Weon; Choi, Don-Ha; Choi, In-Gyu

2008-05-01

In order to investigate the possibility of using waste mushroom logs as a biomass resource for alternative energy production, the chemical and physical characteristics of normal wood and waste mushroom logs were examined. Size reduction of normal wood (145 kW h/tone) required significantly higher energy consumption than waste mushroom logs (70 kW h/tone). The crystallinity value of waste mushroom logs was dramatically lower (33%) than normal wood (49%) after cultivation by Lentinus edodes as spawn. Lignin, an enzymatic hydrolysis inhibitor in sugar production, decreased from 21.07% to 18.78% after inoculation of L. edodes. Total sugar yields obtained by enzyme and acid hydrolysis were higher in waste mushroom logs than in normal wood. After 24h fermentation, 12 g/L ethanol was produced on waste mushroom logs, while normal wood produced 8 g/L ethanol. These results indicate that waste mushroom logs are economically suitable lignocellulosic material for the production of fermentable sugars related to bioethanol production.

Sawmill "Waste"

Treesearch

Fred C. Simmons; Adna R. Bond

1955-01-01

Sawmills have the reputation of being very wasteful in converting logs and bolts into lumber and timbers. Almost everyone has seen the great heaps of sawdust and slabs that collect at sawmills. Frequently the question is asked, "Why doesn't somebody do something about this terrible waste of wood?"

Functionality of liquid smoke as an all-natural antimicrobial in food preservation.

PubMed

Lingbeck, Jody M; Cordero, Paola; O'Bryan, Corliss A; Johnson, Michael G; Ricke, Steven C; Crandall, Philip G

2014-06-01

The smoking of foods, especially meats, has been used as a preservation technique for centuries. Today, smoking methods often involve the use of wood smoke condensates, commonly known as liquid smoke. Liquid smoke is produced by condensing wood smoke created by the pyrolysis of sawdust or wood chips followed by removal of the carcinogenic polyaromatic hydrocarbons. The main products of wood pyrolysis are phenols, carbonyls and organic acids which are responsible for the flavor, color and antimicrobial properties of liquid smoke. Several common food-borne pathogens such as Listeria monocytogenes, Salmonella, pathogenic Escherichia coli and Staphylococcus have shown sensitivity to liquid smoke in vitro and in food systems. Therefore liquid smoke has potential for use as an all-natural antimicrobial in commercial applications where smoke flavor is desired. This review will cover the application and effectiveness of liquid smoke and fractions of liquid smoke as an all-natural food preservative. This review will be valuable for the industrial and research communities in the food science and technology areas. Copyright © 2014. Published by Elsevier Ltd.

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

Summary of Resource Conservation and Recovery Act State Authorization Rule Checklist 179

EPA Pesticide Factsheets

Land Disposal Restrictions -- Phase IV: Treatment Standards for Wood Preserving Wastes, Treatment Standards for Metal Wastes, Zinc Micronutrient Fertilizers, Carbamate Treatment Standards, and K088 Treatment Standards

Jackfruit (Artocarpus heterophyllus lamk) wood waste as a textile natural dye by micowave-assisted extraction method

NASA Astrophysics Data System (ADS)

Qadariyah, Lailatul; Gala, Selfina; Widoretno, Dhaniar Rulandri; Kunhermanti, Delita; Bhuana, Donny S.; Sumarno, Mahfud, Mahfud

2017-05-01

The development of technology causes most of textile industries in Indonesia prefer to use synthetic dyes in the fabric dyeing process. In fact, synthetic dyes is able to have negative effect since it is is toxic to the health of workers and environment. To resolve this issues, one way to do is to use natural dyes. One of untapped potential in Indonesia is wood waste of jackfruit from furniture industry. Jackfruit wood itself containing dyestuffs which gives yellow color pigment so that it can be used as an alternative source of natural dyes. The purpose of this research is to study the effect of extraction time, mass to solvent volume ratio, and microwave power to yield of dyes. The extract of dye analyzed by UV-Visible Spectrophotometer and GC-MS, along the coloring and endurance tests of natural dyes on fabric and compare it with synthetic dyes. In this research, material is going to be extracted is the wood of jackfruit (Artocarpus heterophyllus lamk) with material size between 35 mesh - 60 mesh. The extraction process is done by using ethanol 96%. Extraction using MAE is carried out at the ratio of materials to solvent of 0,02-0,1 g/mL, the microwave power of 100-800 Watt, and the extraction time of 10-90 minutes. The conclusion is at microwave power of 400 Watt, material to solvent ratio of the 0,02 g/mL, the yield is 3,39% while at microwave power of 600 Watt, material to solvent ratio of the 0,02 g/mL, the yield is 3,67% with extraction time of 30 minutes. The highest recovery from ethanol 96% solvent is 60,41%. The result of UV-Vis Spectrophotometry and GC-MS test show that there is a chromophore compound in the extract of natural dye. The test results show the natural dyes of jackfruit wood can be used to coloring on the textile because it can gives staining result permanently.

Penetration and Effectiveness of Micronized Copper in Refractory Wood Species

PubMed Central

Civardi, Chiara; Van den Bulcke, Jan; Schubert, Mark; Michel, Elisabeth; Butron, Maria Isabel; Boone, Matthieu N.; Dierick, Manuel; Van Acker, Joris; Wick, Peter; Schwarze, Francis W. M. R.

2016-01-01

The North American wood decking market mostly relies on easily treatable Southern yellow pine (SYP), which is being impregnated with micronized copper (MC) wood preservatives since 2006. These formulations are composed of copper (Cu) carbonate particles (CuCO3·Cu(OH)2), with sizes ranging from 1 nm to 250 μm, according to manufacturers. MC-treated SYP wood is protected against decay by solubilized Cu2+ ions and unreacted CuCO3·Cu(OH)2 particles that successively release Cu2+ ions (reservoir effect). The wood species used for the European wood decking market differ from the North American SYP. One of the most common species is Norway spruce wood, which is poorly treatable i.e. refractory due to the anatomical properties, like pore size and structure, and chemical composition, like pit membrane components or presence of wood extractives. Therefore, MC formulations may not suitable for refractory wood species common in the European market, despite their good performance in SYP. We evaluated the penetration effectiveness of MC azole (MCA) in easily treatable Scots pine and in refractory Norway spruce wood. We assessed the effectiveness against the Cu-tolerant wood-destroying fungus Rhodonia placenta. Our findings show that MCA cannot easily penetrate refractory wood species and could not confirm the presence of a reservoir effect. PMID:27649315

Penetration and Effectiveness of Micronized Copper in Refractory Wood Species.

PubMed

Civardi, Chiara; Van den Bulcke, Jan; Schubert, Mark; Michel, Elisabeth; Butron, Maria Isabel; Boone, Matthieu N; Dierick, Manuel; Van Acker, Joris; Wick, Peter; Schwarze, Francis W M R

2016-01-01

The North American wood decking market mostly relies on easily treatable Southern yellow pine (SYP), which is being impregnated with micronized copper (MC) wood preservatives since 2006. These formulations are composed of copper (Cu) carbonate particles (CuCO3·Cu(OH)2), with sizes ranging from 1 nm to 250 μm, according to manufacturers. MC-treated SYP wood is protected against decay by solubilized Cu2+ ions and unreacted CuCO3·Cu(OH)2 particles that successively release Cu2+ ions (reservoir effect). The wood species used for the European wood decking market differ from the North American SYP. One of the most common species is Norway spruce wood, which is poorly treatable i.e. refractory due to the anatomical properties, like pore size and structure, and chemical composition, like pit membrane components or presence of wood extractives. Therefore, MC formulations may not suitable for refractory wood species common in the European market, despite their good performance in SYP. We evaluated the penetration effectiveness of MC azole (MCA) in easily treatable Scots pine and in refractory Norway spruce wood. We assessed the effectiveness against the Cu-tolerant wood-destroying fungus Rhodonia placenta. Our findings show that MCA cannot easily penetrate refractory wood species and could not confirm the presence of a reservoir effect.

Fifty-Year Durability Evaluation of Posts Treated with Industrial Wood Preservatives

Treesearch

Stan T. Lebow; Patricia Lebow; Bessie Woodward; Grant T. Kirker; Rachel Arango

2015-01-01

Long-term durability data are needed to improve service life estimates for treated wood products used as critical structural supports in industrial applications. This article reports the durability of longleaf pine (Pinus palustris) posts pressure treated with ammoniacal copper arsenate (ACA), chromated copper arsenate (CCA), creosote, or...

Online elemental analysis of process gases with ICP-OES: A case study on waste wood combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wellinger, Marco, E-mail: marco.wellinger@gmail.com; Ecole Polytechnique Federale de Lausanne; Wochele, Joerg

2012-10-15

Highlights: Black-Right-Pointing-Pointer Simultaneous measurements of 23 elements in process gases of a waste wood combustor. Black-Right-Pointing-Pointer Mobile ICP spectrometer allows measurements of high quality at industrial plants. Black-Right-Pointing-Pointer Continuous online measurements with high temporal resolution. Black-Right-Pointing-Pointer Linear correlations among element concentrations in the raw flue gas were detected. Black-Right-Pointing-Pointer Novel sampling and calibration methods for ICP-OES analysis of process gases. - Abstract: A mobile sampling and measurement system for the analysis of gaseous and liquid samples in the field was developed. An inductively coupled plasma optical emission spectrometer (ICP-OES), which is built into a van, was used as detector. Themore » analytical system was calibrated with liquid and/or gaseous standards. It was shown that identical mass flows of either gaseous or liquid standards resulted in identical ICP-OES signal intensities. In a field measurement campaign trace and minor elements in the raw flue gas of a waste wood combustor were monitored. Sampling was performed with a highly transport efficient liquid quench system, which allowed to observe temporal variations in the elemental process gas composition. After a change in feedstock an immediate change of the element concentrations in the flue gas was detected. A comparison of the average element concentrations during the combustion of the two feedstocks showed a high reproducibility for matrix elements that are expected to be present in similar concentrations. On the other hand elements that showed strong differences in their concentration in the feedstock were also represented by a higher concentration in the flue gas. Following the temporal variations of different elements revealed strong correlations between a number of elements, such as chlorine with sodium, potassium and zinc, as well as arsenic with lead, and calcium with strontium.« less

Extractive waste exploitation towards the natural resource preservation: two Italian case studies

NASA Astrophysics Data System (ADS)

Antonella Dino, Giovanna; Rossetti, Piergiorgio; Biglia, Giulio; Mehta, Neha; Rodeghiero, Franco

2017-04-01

In 2012 the extractive industry represented the second most important sector in terms of waste quantities produced in the EU-27 (29% or 734 million tons). Italy was and still is one of the most important countries as for quarry and mine exploitation, with a consequent huge production of extractive waste (EW; represented by rock waste, operating residues and tailings), which are present in mining dumps (EW facilities). The EU guidelines about waste management aim to the exploitation, based on environmental protection, of any kind of material which can be recovered and recycled, with a consequent natural resources preservation. The decision n. 1600/2002/CE, establishing the VI Environment Action Program, pushes to the revision of the legislation on waste and to the development of specific actions for waste prevention and management. The decisive factors to achieve these results are the minimization of waste production and the recovery of as much waste as possible from the different productive cycles and from landfills, including EW facilities. According to this approach, "WASTE" must be considered as a "RESOURCE", and "LANDFILLS" as "NEW ORE BODIES". In the recent years several projects investigate the recovery of Critical Raw Materials (CRM) and SRM from landfills (Smart Ground, Prosum, etc.). The main objective of the present research, which is one of the activities linked to Smart Ground project (Grant Agreement No 641988), is the estimation of the SRM and CRM present in two selected Italian EW facilities: - Campello Monti mining site (NE Piedmont Region), important for Ni exploitation. The area is characterized by the presence of EW facilities, mainly represented by rock waste and operating residues. - Gorno mining site (N Lombardy Region), famous for Zn exploitation. The area is characterized by the presence of several EW facility areas, mainly represented by rock waste dumps and tailing basins. To appreciate if an EW facility can be considered as an "ore body

Preliminary investigation on the natural durability of guayule (Parthenium argentatum) based wood products

Treesearch

Francis S. Nakayama; Poo. Chow; Dilpreet S. Bajwa; John A. Youngquist; James H. Muehl; Andrzej M. Krzysik

2000-01-01

Conventional preservatives used to protect wood from insect and microbial damages are presently of major concern to human health and the environment. Finding alternative and economical preservatives has not been successful. Previous studies have shown that the resinous material extracted from the guayule plant (Parthenium argentatum, Gray) has both insect- and...

Gene expression analysis of copper tolerance and wood decay in the brown rot fungus Fibroporia radiculosa

USDA-ARS?s Scientific Manuscript database

Many brown rot fungi are capable of rapidly degrading wood and are copper-tolerant. To better understand the genes that control these processes, we examined gene expression of Fibroporia radiculosa growing on wood treated with a copper-based preservative that combined copper carbonate with dimethyld...

USARCENT AOR Contingency Base Waste Stream Analysis: An Analysis of Solid Waste Streams at Five Bases in the U. S. Army Central (USARCENT) Area of Responsibility

DTIC Science & Technology

2013-03-31

certainly remain comingled with other solid waste. For example, some bases provided containers for segregation of recyclables including plastic and...prevalent types of solid waste are food (19.1% by average sample weight), wood (18.9%), and plastics (16.0%) based on analysis of bases in...within the interval shown. Food and wood wastes are the largest components of the average waste stream (both at ~19% by weight), followed by plastic

Distribution of borates around point source injections in wood members exposed outside

Treesearch

Rodney C. De Groot; Colin C. Felton; Douglas M. Crawford

2000-01-01

In bridge timbers, wood decay is usually found where water has accessed the end-grain surfaces. In preservative-treated members, end-grain surfaces are most likely to be those resulting from on-site framing cuts or borings. Because these at-risk surfaces are easy to see, it seems feasible to establish a program where diffusible preservatives are repetitively inserted...

Assessing the Long-Term Efficacy of Geotextiles in Preserving Archaeological Wooden Shipwrecks in the Marine Environment

NASA Astrophysics Data System (ADS)

Pournou, Anastasia

2017-09-01

Archaeological wood cannot be found preserved in the marine ecosystem unless it is buried in anoxic or dysoxic sediments. These habitats do not allow the growth and activity of wood degraders, and thus wooden shipwrecks can survive within these environments for centuries. However, due to natural factors or anthropogenic interventions wood can be re-exposed to the oxygenated water column, where it disintegrates rapidly. In such cases, in situ preservation becomes a main priority, as lifting and conservation are not usually feasible. One of the most common in situ preservation methods is the covering of wood with geotextiles. To date however, even though this method has been used worldwide the past decades, its long-term performance and effectiveness hasn't been evaluated. This work presents, for the first time, results on the efficacy of geotextiles used for 12 years on a shipwreck found in the Mediterranean. Fabric performance was evaluated based on wreck timbers condition, its physical, mechanical and hydraulic properties and the ecological and hydrographical profile of the underwater site created, following its application. Obtained results demonstrated that wreck timbers covered with geotextiles did not show signs of attack during the 12 years of in situ preservation. Geotextiles properties were found to be adequately retained when compared with properties of new unused geotextiles. The fabric had entrapped sediment and was colonised by the local flora and fauna, re-establishing anoxic conditions. This work showed that geotextiles can successfully preserve in situ wooden shipwrecks in high biodeterioration risk environments for at least a 10 year period.

Assessing the Long-Term Efficacy of Geotextiles in Preserving Archaeological Wooden Shipwrecks in the Marine Environment

NASA Astrophysics Data System (ADS)

Pournou, Anastasia

2018-04-01

Archaeological wood cannot be found preserved in the marine ecosystem unless it is buried in anoxic or dysoxic sediments. These habitats do not allow the growth and activity of wood degraders, and thus wooden shipwrecks can survive within these environments for centuries. However, due to natural factors or anthropogenic interventions wood can be re-exposed to the oxygenated water column, where it disintegrates rapidly. In such cases, in situ preservation becomes a main priority, as lifting and conservation are not usually feasible. One of the most common in situ preservation methods is the covering of wood with geotextiles. To date however, even though this method has been used worldwide the past decades, its long-term performance and effectiveness hasn't been evaluated. This work presents, for the first time, results on the efficacy of geotextiles used for 12 years on a shipwreck found in the Mediterranean. Fabric performance was evaluated based on wreck timbers condition, its physical, mechanical and hydraulic properties and the ecological and hydrographical profile of the underwater site created, following its application. Obtained results demonstrated that wreck timbers covered with geotextiles did not show signs of attack during the 12 years of in situ preservation. Geotextiles properties were found to be adequately retained when compared with properties of new unused geotextiles. The fabric had entrapped sediment and was colonised by the local flora and fauna, re-establishing anoxic conditions. This work showed that geotextiles can successfully preserve in situ wooden shipwrecks in high biodeterioration risk environments for at least a 10 year period.

Degradation of carbohydrates and lignins in buried woods

USGS Publications Warehouse

Hedges, J.I.; Cowie, G.L.; Ertel, J.R.; James, Barbour R.; Hatcher, P.G.

1985-01-01

Spruce, alder, and oak woods deposited in coastal sediments were characterized versus their modern counterparts by quantification of individual neutral sugars and lignin-derived phenols as well as by scanning electron microscopy, 13C NMR, and elemental analysis. The buried spruce wood from a 2500 yr old deposit was unaltered whereas an alder wood from the same horizon and an oak wood from an open ocean sediment were profoundly degraded. Individual sugar and lignin phenol analyses indicate that at least 90 and 98 wt% of the initial total polysaccharides in the buried alder and oak woods, respectively, have been degraded along with 15-25 wt% of the lignin. At least 75% of the degraded biopolymer has been physically lost from these samples. This evidence is supported by the SEM, 13C NMR and elemental analyses, all of which indicate selective loss of the carbohydrate moiety. The following order of stability was observed for the major biochemical constituents of both buried hardwoods: vanillyl and p-hydroxyl lignin structural units > syringyl lignin structural units > pectin > ??-cellulose > hemicellulose. This sequence can be explained by selective preservation of the compound middle lamella regions of the wood cell walls. The magnitude and selectivity of the indicated diagenetic reactions are sufficient to cause major changes in the chemical compositions of wood-rich sedimentary organic mixtures and to provide a potentially large in situ nutrient source. ?? 1985.

Factors effecting paint performance on wood siding

Treesearch

Christopher G. Hunt; R. Sam Williams; Mark Knaebe; Peter Sotos; Steven Lacher

2009-01-01

Several different studies are compared to assess the effectiveness of commercial water repellent preservatives (WRP’s) in the late 1990’s on vertical and horizontal siding. Besides WRP, variables included wood species, exposure location (Wisconsin or Mississippi), and solid color stain vs. primer + paint. Data on substrate checking and paint flaking are presented....

10 CFR 1303.115 - Preservation of records.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Preservation of records. 1303.115 Section 1303.115 Energy NUCLEAR WASTE TECHNICAL REVIEW BOARD PUBLIC INFORMATION AND REQUESTS § 1303.115 Preservation of records. The Board shall preserve all correspondence pertaining to the requests that it receives under this...

10 CFR 1303.115 - Preservation of records.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Preservation of records. 1303.115 Section 1303.115 Energy NUCLEAR WASTE TECHNICAL REVIEW BOARD PUBLIC INFORMATION AND REQUESTS § 1303.115 Preservation of records. The Board shall preserve all correspondence pertaining to the requests that it receives under this...

10 CFR 1303.115 - Preservation of records.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Preservation of records. 1303.115 Section 1303.115 Energy NUCLEAR WASTE TECHNICAL REVIEW BOARD PUBLIC INFORMATION AND REQUESTS § 1303.115 Preservation of records. The Board shall preserve all correspondence pertaining to the requests that it receives under this...

10 CFR 1303.115 - Preservation of records.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Preservation of records. 1303.115 Section 1303.115 Energy NUCLEAR WASTE TECHNICAL REVIEW BOARD PUBLIC INFORMATION AND REQUESTS § 1303.115 Preservation of records. The Board shall preserve all correspondence pertaining to the requests that it receives under this...

10 CFR 1303.115 - Preservation of records.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Preservation of records. 1303.115 Section 1303.115 Energy NUCLEAR WASTE TECHNICAL REVIEW BOARD PUBLIC INFORMATION AND REQUESTS § 1303.115 Preservation of records. The Board shall preserve all correspondence pertaining to the requests that it receives under this...

Reactive Processing of Environmentally Conscious, Biomorphic Ceramics from Natural Wood Precursors

NASA Technical Reports Server (NTRS)

Singh, M.; Yee, Bo-Moon

2003-01-01

Environmentally conscious, biomorphic ceramics (Ecoceramics) are a new class of materials that are manufactured from renewable resources and wastes. In this study, silicon carbide and oxide-based biomorphic ceramics have been fabricated from pine and jelutong wood precursors. A carbonaceous preform is produced through wood pyrolysis and subsequent infiltration with oxides (ZrO2 sols) and liquid silicon to form ceramics. These biomorphic ceramics show a wide variety of microstructures, densities, and hardness behavior that are determined by the type of wood and infiltrants selected.

Effect of simulated rainfall and weathering on release of preservative elements from CCA treated wood

Treesearch

Stan Lebow; R. Sam Williams; Patricia Lebow

2003-01-01

The release of arsenic from wood pressure-treated with chromated copper arsenate (CCA) can be decreased by application of wood finishes, but little is known about the types of finishes that are best suited for this purpose. This study evaluated the effects of finish water repellent content and ultraviolet (UV) radiation on the release of arsenic, copper, and chromium...

Wood biodegradation in laboratory-scale landfills.

PubMed

Wang, Xiaoming; Padgett, Jennifer M; De la Cruz, Florentino B; Barlaz, Morton A

2011-08-15

The objective of this research was to characterize the anaerobic biodegradability of major wood products in municipal waste by measuring methane yields, decay rates, the extent of carbohydrate decomposition, carbon storage, and leachate toxicity. Tests were conducted in triplicate 8 L reactors operated to obtain maximum yields. Measured methane yields for red oak, eucalyptus, spruce, radiata pine, plywood (PW), oriented strand board (OSB) from hardwood (HW) and softwood (SW), particleboard (PB) and medium-density fiberboard (MDF) were 32.5, 0, 7.5, 0.5, 6.3, 84.5, 0, 5.6, and 4.6 mL CH(4) dry g(-1), respectively. The red oak, a HW, exhibited greater decomposition than either SW (spruce and radiata), a trend that was also measured for the OSB-HW relative to OSB-SW. However, the eucalyptus (HW) exhibited toxicity. Thus, wood species have unique methane yields that should be considered in the development of national inventories of methane production and carbon storage. The current assumption of uniform biodegradability is not appropriate. The ammonia release from urea formaldehyde as present in PB and MDF could contribute to ammonia in landfill leachate. Using the extent of carbon conversion measured in this research, 0-19.9%, predicted methane production from a wood mixture using the Intergovernmental Panel for Climate Change waste model is only 7.9% of that predicted using the 50% carbon conversion default.

Uses for Sawdust, Shavings, And Waste Chips

Treesearch

J. M. Harkin

1969-01-01

Although many outlets are available for the utilization of wood fines, economical disposal of sawdust, shavings, and waste chips remains a problem of growing concern to the wood industry. This report summarizes current uses for wood residues and provides sources of further information on available outlets, processing methods, and economic considerations.

ASSESSING CHILDREN'S EXPOSURES TO THE WOOD PRESERVATIVE CCA (CHROMATED COPPER ARSENATE) ON TREATED PLAYSETS AND DECKS

EPA Science Inventory

Concerns have been raised regarding the safety of young children contacting arsenic and chromium residues while playing on and around Chromated Copper Arsenate (CCA) treated wood playground structures and decks. Although CCA registrants voluntarily canceled treated wood for re...

Evaluating landfill disposal of chromated copper arsenate (CCA) treated wood and potential effects on groundwater: evidence from Florida.

PubMed

Saxe, Jennifer K; Wannamaker, Eric J; Conklin, Scott W; Shupe, Todd F; Beck, Barbara D

2007-01-01

Chromated copper arsenate (CCA) treated wood has been used for more than 50 years. Recent attention has been focused on appropriate disposal of CCA-treated wood when its service life ends. Groups in the US and Europe concerned with the possibility of arsenic migration to groundwater from disposed CCA-treated wood have proposed that consumers be required to dispose of the wood as a hazardous waste, in the most protective of landfills. We examined available data for evidence of arsenic migration from unlined construction and demolition (C&D) debris landfills in Florida, where CCA-treated wood is disposed. Florida was chosen because soil, groundwater, landfill design, weather, and levels of CCA-treated wood use make the state a uniquely sensitive indicator for observing arsenic migration from CCA-treated wood disposal sites, should it occur. We developed and quality-checked a CCA-treated wood disposal model to estimate the amount of wood and associated arsenic disposed. By 2000, an estimated 13 million kg of arsenic in CCA-treated wood was disposed in Florida; however, groundwater monitoring data do not indicate that arsenic is migrating from unlined C&D landfills. Our results provide evidence that highly stringent regulation of CCA-treated wood disposal, such as treatment as a hazardous waste, is unnecessary.

Effect of weathering on chromated copper arsenate (CCA) treated wood : leaching of metal salts and change in water repellency

Treesearch

R. Sam Williams; Stan Lebow; Patricia Lebow

2003-01-01

Wood pressure-treated with chromated copper arsenate (CCA) wood preservative is commonly used for outdoor construction. Oxides of arsenic, copper, and chromium are bound in the wood by a complex series of chemical reactions, but a small percentage of these compounds are gradually released by leaching and weathering. Recent studies suggest that the release of these...

Quantification of metals in preservatively-treated lumber using laser induced breakdown spectroscopy

Treesearch

Brad Gething; John Janowiak; Bob Falk

2006-01-01

The laser induced breakdown spectroscopy (LIBS) technique was evaluated for its capability of quantifying CCA in preservative-treated wood. The results of the study reveal that the LIBS technique can be used to predict the amount of preservative based on chromium peak analysis, but further refinement of the process is necessary before the technique is practiced. The...

Gene Expression Analysis of Copper Tolerance and Wood Decay in the Brown Rot Fungus Fibroporia radiculosa

Treesearch

J. D. Tang; L. A. Parker; A. D. Perkins; T. S. Sonstegard; S. G. Schroeder; D. D. Nicholas; S. V. Diehl

2013-01-01

High-throughput transcriptomics was used to identify Fibroporia radiculosa genes that were differentially regulated during colonization of wood treated with a copper-based preservative. The transcriptome was profiled at two time points while the fungus was growing on wood treated with micronized copper quat (MCQ). A total of 917 transcripts were...

Blood Preservation Study.

DTIC Science & Technology

1979-04-30

10. Wood, L.A. and Beutler, E.: The effect of periodic mixing on the preservation of 2,3- diphosphoglycerate (2,3-DPG)":’::’: levels in stored blood...patient. 1.1.3. .The 2,3- diphosphoglycerate (2,3-DPG) content of blood stored in ACD declines rapidly after one or two days of storage, while" in CPD the...decline of 2,3-DPG levels is delayed for only one week. 2,3-DPG is an important modulator of the affinity of hemoglobin for oxygen (5,6). When the

Increase in energy efficiency of use of vegetable waste

NASA Astrophysics Data System (ADS)

Safin, R. R.; Safiullina, A. K.; Nazipova, F. V.

2017-10-01

Wastes of woodworking which are exposed to granulation for equalization of humidity, dispersion and also for increase in energy efficiency are the most widespread types of alternative fuel in Russia. Besides, one of the effective methods of the increase in calorific capability of granulates now is the preliminary torrefaction of wood waste - heat treatment without air oxygen access. However this technology is rather researched in detail only in relation to wood particles, while pellets from wastes of agricultural productions are also popular in the market in recent years. The possibility of the increase of the efficiency of production of pellets from sunflower pod by torrefaction is considered in this article, and the analysis of their characteristics in comparison with wood pellets is carried out. It is established that the process of heat treatment of waste of sunflower production is similar to torrefaction of wood raw materials in many respects; therefore, the equipment with similar characteristics can be used. According to the received results on pellet’s properties it is established that hygroscopicity and swelling of samples of fuel granules from sunflower pod considerably decreases with the increase in temperature of treatment that simplifies requirements for their storage and transportation. Besides, it is defined that torrefaction of the granulated fuel from sunflower pod does not yield in calorific properties to the similar fuel granules made of wood sawdust. Thus feasibility of use of heat treatment in production of fuel granules from waste of vegetable raw materials is proved.

Variation of arsenic concentration on surfaces of in-service CCA-treated wood planks in a park and its influencing field factors.

PubMed

Tang, Ya; Gao, Wei; Wang, Xiuli; Ding, Shiming; An, Taicheng; Xiao, Weiyang; Wong, Ming H; Zhang, Chaosheng

2015-01-01

Wood preservatives can protect wood from dry rot, fungi, mould and insect damage, and chromated copper arsenate (CCA) has been used as an inorganic preservative for many years. However, wood treated with CCA has been restricted from residential uses in the EU from June 30, 2004, due to its potential toxicity. Such a regulation is not in place in China yet, and CCA-treated wood is widely used in public parks. A portable XRF analyser was used to investigate arsenic (As) concentration on surfaces of in-service CCA-treated wood planks in a popular park as well as the influencing field factors of age in-service, immersion and human footfall. With a total of 1207 readings, the observed As concentrations varied from below the detection limit (<10 mg/kg) to 15,746 mg/kg with a median of 1160 mg/kg. Strong variation of As concentrations were observed in different wood planks of the same age, on the surface of the same piece of wood, inside the same piece of wood, and different surfaces of walkway planks, hand rails and poles in the field. The oldest planks exhibited high As concentrations, which was related to its original treatment with high retention of CCA preservative. The effect of immersion in the field for about 4 months was insignificant for As concentration on the surfaces. However, a significant reduction of As was observed for immersion combined with human footfall (wiping by shoes). Human traffic in general caused slightly reduced and more evenly distributed As concentrations on the wood surfaces. The strong variation, slow aging and relatively weak immersion effects found in this study demonstrate that the in-service CCA-treated wood poses potential health risks to the park users, due to easy dermal contact especially when the wood is wet after rainfall. It is suggested that further comprehensive investigations and risk assessments of CCA-treated wood in residential areas in China are needed, and precautionary measures should be considered to reduce the

Fungal and bacterial community succession differs for three wood types during decay in a forest soil.

PubMed

Prewitt, Lynn; Kang, Youngmin; Kakumanu, Madhavi L; Williams, Mark

2014-08-01

Wood decomposition by soil microorganisms is vital to carbon and nutrient cycles of forested ecosystems. Different wood types decompose at different rates; however, it is not known if there are differences in microbial community succession associated with the decay of different wood types. In this study, the microbial community associated with the decay of pine (decay-susceptible wood), western red cedar (decay resistant) and ACQ-treated pine (Ammoniacal Copper Quaternary, preservative-treated pine for decay resistance) in forest soil was characterized using DNA sequencing, phospholipid fatty acid (PLFA) analysis, and microbial activity over a 26-month period. Bray-Curtis ordination using an internal transcribed spacer (ITS) sequence and PLFA data indicated that fungal communities changed during succession and that wood type altered the pattern of succession. Nondecay fungi decreased over the 26 months of succession; however, by 18 months of decay, there was a major shift in the fungal communities. By this time, Trametes elegans dominated cedar and Phlebia radiata dominated pine and ACQ-treated pine. The description of PLFA associated with ACQ-treated pine resembled cedar more than pine; however, both PLFA and ITS descriptions indicated that fungal communities associated with ACQ-treated pine were less dynamic, perhaps a result of the inhibition by the ACQ preservative, compared with pine and cedar. Overall, fungal community composition and succession were associated with wood type. Further research into the differences in community composition will help to discern their functional importance to wood decay.

Significance of wood extractives for wood bonding.

PubMed

Roffael, Edmone

2016-02-01

Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

Recovery, reuse and recycling by the United States wood packaging industry: 1993-2006

Treesearch

Robert J. Bush; Philip A. Araman; E. Bradley Hager

2007-01-01

The packaging industry is an important market for wood materials, especially low grade hardwoods. Approximately one-third of U.S. hardwood lumber production is utilized in the production of pallets and containers. The industry recovers significant volumes of pallets and containers from the waste stream for re-use, repair, and recycling. Industry by-products (both wood...

Resistance of borax–copper treated wood in aboveground exposure to attack by Formosan subterranean termites

Treesearch

Stan Lebow; Bessie Woodward; Douglas Crawford; William Abbott

2005-01-01

The spread of Formosan subterranean termites (FSTs) in the southern United States has increased public interest in finding a preservative treatment to protect framing lumber from termite attack. This study evaluated the use of a borax-based preservative to protect wood from FST attack. Southern Pine and Douglas-fir specimens were pressure-treated with three...

MODELING AGGREGATE EXPOSURE AND DOSE OF CHILDREN TO A WOOD TREATMENT PRESERVATIVE FROM PLAYSETS AND HOME DECKS

EPA Science Inventory

Pressure- or non-pressure- treated lumber may pose a potential health hazard to children if the children contact certain chemicals in soils around leaching wood structures and/or in dislodgeable residues that may form on the wood surfaces of the structures. A physically-based,...

Pallets: A Growing Source of Recycled Wood

Treesearch

Robert J. Bush; Vijay S. Reddy; Philip A. Araman

1997-01-01

Considerable volumes of solid hardwoods, solid softwoods, and wood panels are used to manufacture pallets and containers in the United States. Increasing quantities of these materials are recovered from the waste stream for reuse and recycling. Two important groups involved in this recovery and recycling are firms in the pallet industry (SIC 2448) and landfill...

The Sea-Floor Mapping Facility at the U.S. Geological Survey Woods Hole Field Center, Woods Hole, Massachusetts

USGS Publications Warehouse

Deusser, Rebecca E.; Schwab, William C.; Denny, Jane F.

2002-01-01

Researchers of the sea-floor mapping facility at the U.S. Geological Survey (USGS) Woods Hole Field Center in Woods Hole, Mass., use state-of-the-art technology to produce accurate geologic maps of the sea floor. In addition to basic bathymetry and morphology, sea-floor maps may contain information about the distribution of sand resources, patterns of coastal erosion, pathways of pollutant transport, and geologic controls on marine biological habitats. The maps may also show areas of human impacts, such as disturbance by bottom fishing and pollution caused by offshore waste disposal. The maps provide a framework for scientific research and provide critical information to decisionmakers who oversee resources in the coastal ocean.

The use of electrochemical impedance spectroscopy (EIS) to measure the corrosion of metals in contact with wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2005-01-01

Although preservative treatments prolong the life of wood, they can also contribute to the corrosion of fasteners. The corrosion of fasteners merits further study because it can affect the long-term durability of structures and fundamental knowledge of corrosion in wood is limited. The goal of this study is to determine the viability of electrochemical impedance...

Eco-friendly wood-based solid-state flexible supercapacitors from wood transverse section slice and reduced graphene oxide

NASA Astrophysics Data System (ADS)

Lv, Shaoyi; Fu, Feng; Wang, Siqun; Huang, Jingda; Hu, La

2015-07-01

An interesting wood-based all-solid-state supercapacitor is produced using reduced graphene oxide (RGO) coated on wood transverse section slice (WTSS) as electrode material by means of a low-cost, eco-friendly, and simple method for the first time. The RGO-coated WTSS electrode has a porous 3D honeycomb framework due to the hierarchical cellular structure of the WTSS substrate and can function as an electrolyte reservoir. This special construction endows this novel electrode with good areal capacitance (102 mF cm-2) and excellent cyclic stability (capacitance retention of 98.9% after 5000 cycles). In addition, the supercapacitors exhibit good mechanical flexibility and preserve almost constant capacitive behavior under different bending conditions. Our study introduces a new and eco-friendly material design for electrodes in future flexible energy storage devices that closely resemble natural materials. [Figure not available: see fulltext.

Wood handbook : wood as an engineering material.

Treesearch

Forest Products Laboratory

1999-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Wood handbook : wood as an engineering material

Treesearch

Robert J. Ross; Forest Products Laboratory USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Waste-to-Energy and Fuel Cell Technologies Overview

DTIC Science & Technology

2011-01-13

Integration of stationary fuel cells with biomass gasification is a developing technology that is in need of demonstration. Innovation for Our...the PureCell®400 Innovation for Our Energy Future Gasification of wood wastes is another potential source of useful fuel gas. Wood waste... Gasification → Cleanup → Fuel Cell Gasification uses high temperature to convert cellulosic materials to fuel gas • Hydrogen (H2) • Carbon monoxide (CO

Copper tolerance of brown-rot fungi : oxalic acid production in southern pine treated with arsenic-free preservatives

Treesearch

Frederick Green; Carol A. Clausen

2005-01-01

The voluntary withdrawal of chromated copper arsenate (CCA)-treated wood from most residential applications has increased the use of non-arsenical copper-based organic wood preservatives. Because the arsenic component of CCA controlled copper tolerant fungi, scientists have renewed interest in and concern about the decay capacity in the important copper-tolerant group...

Isolating metal-tolerant bacteria capable of removing copper, chromium, and arsenic from treated wood

Treesearch

Carol A. Clausen

2000-01-01

Bioremediation of chromated copper arsenate-treated waste wood with one or more metal-tolerant bacteria is a potential method of naturally releasing metals from treated wood fibre. Sampling eight environments with elevated levels of copper, chromium, and arsenic resulted in the isolation of 28 bacteria with the capability of releasing one or more of the components from...

Comparing Life-Cycle Carbon and Energy Impacts for Biofuel, Wood Product, and Forest Management

Treesearch

Bruce Lippke; Richard Gustafson; Richard Venditti; Philip Steele; Timothy A. Volk; Elaine Oneil; Leonard Johnson; Maureen E. Puettmann; Kenneth Skog

2012-01-01

The different uses of wood result in a hierarchy of carbon and energy impacts that can be characterized by their efficiency in displacing carbon emissions and/or in displacing fossil energy imports, both being current national objectives. When waste wood is used for biofuels (forest or mill residuals and thinnings) fossil fuels and their emissions are reduced without...

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, David N.; Emerick, Robert W.; England, Alfred B.

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic compositemore » products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systems—without cell debris removal—is a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for

Temporal dynamics of instream wood in headwater streams draining mixed Carpathian forests

NASA Astrophysics Data System (ADS)

Galia, Tomáš; Šilhán, Karel; Ruiz-Villanueva, Virginia; Tichavský, Radek; Stoffel, Markus

2017-09-01

Instream wood can reside in fluvial systems over varying periods depending on its geographical context, instream position, tree species, piece size, and fluvial environment. In this paper, we investigate the residence time of two typical species representing a majority of instream wood in steep headwaters of the Carpathians and located under mixed forest canopy. Residence times of individual logs were then confronted with other wood parameters (i.e., wood dimensions, mean annual increment rate, tree age, class of wood stabilisation and decay, geomorphic function of wood pieces, and the proportion of the log length within the active channel). Norway spruce (Picea abies (L.) Karst.) samples indicated more than two times longer mean and maximal residence times as compared to European beech (Fagus sylvatica L.) based on the successful cross-dating of 127 logs. Maximum residence time in the headwaters was 128 years for P. abies and 59 years for F. sylvatica. We demonstrate that log age and log diameter played an important role in the preservation of wood in the fluvial system, especially in the case of F. sylvatica instream wood. By contrast, we did not observe any significant trends between wood residence time and total wood length. Instream wood with geomorphic functions (i.e., formation of steps and jams) did not show any differences in residence time as compared to nonfunctional wood. Nevertheless, we found shorter residence times for hillslope-stabilised pieces when compared to pieces located entirely in the channel (either unattached or stabilised by other wood or bed sediments). We also observed changes of instream wood orientation with respect to wood residence time. This suggests some movement of instream wood (i.e., its turning or short-distance transport), including pieces longer than channel width in the steep headwaters studied here (1.5 ≤ W ≤ 3.5 m), over the past few decades.

Cleanups In My Community (CIMC) - Hazardous Waste Corrective Actions, National Layer

EPA Pesticide Factsheets

This data layer provides access to Hazardous Waste Corrective Action sites as part of the CIMC web service. Hazardous waste is waste that is dangerous or potentially harmful to our health or the environment. Hazardous wastes can be liquids, solids, gases, or sludges. They can be discarded commercial products, like cleaning fluids or pesticides, or the by-products of manufacturing processes. The RCRA Corrective Action Program, run by EPA and 43 authorized states and territories, works with facilities that have treated, stored, or disposed of hazardous wastes (TSDs) to protect public health and the environment by investigating and cleaning up hazardous releases to soil, ground water, surface water, and air at their facilities.RCRA Corrective Action sites in all 50 states and four U.S. territories cover 18 million acres of land.EPA estimates that more than 35 million people, roughly 12 percent of the U.S. population, live within one mile of a RCRA Corrective Action site (based on the 2000 U.S. Census).RCRA Corrective Action facilities include many current and former chemical manufacturing plants, oil refineries, lead smelters, wood preservers, steel mills, commercial landfills, and a variety of other types of entities. Due to poor practices prior to environmental regulations, Corrective Action facilities have left large stretches of river sediments laden with PCBs; deposited lead in residential yards and parks beyond site boundaries; polluted drinking water wells

Analyses of the wood preservative component N-cyclohexyl-diazeniumdioxide in impregnated pine sapwood by direct thermal desorption-gas chromatography-mass spectrometry.

PubMed

Jüngel, Peter; de Koning, Sjaak; Brinkman, Udo A Th; Melcher, Eckhard

2002-04-12

Investigations concerning the qualitative and quantitative determination of the organic wood preservative component N-cyclohexyl-diazeniumdioxide (HDO) in treated timber were carried out by means of direct thermal desorption-gas chromatography-mass spectrometry (DTD-GC-MS). It could be shown that the identification of HDO in treated pine sapwood (Pinus sylyestris L.) is relatively simple using this analytical technique. Quantification of this active ingredient can be carried out using the peak area of the specific mass fragment m/z 114. A calibration curve with a high correlation coefficient was obtained in the range from 40 to 550 mg HDO per kg timber. Furthermore it can be deduced that the results obtained are characterised by an excellent reproducibility with standard deviations ranging from 5 to 10% in general. For the chosen experimental set up a detection limit of 4 mg HDO per kg treated pine sapwood was calculated, although merely 20% of the active ingredient was desorbed.

High-resolution reconstruction of Arctic paleoclimate derived from 53 million year old kimberlite-hosted Metasequoia wood

NASA Astrophysics Data System (ADS)

Walker, J. J.; Halfar, J.; Schulze, D.; Gedalof, Z.; Moore, G. W. K.

2009-04-01

The recovery of exceptionally well preserved Eocene wood from kimberlite pipes in the Lac de Gras region of the Northwest Territories, Canada, has allowed for the characterization of the local temperature and hydrologic patterns on an annual scale for this arctic ecosystem (present day latitude: 64 deg N). Wood fragments of ancient Metasequoia sp. trees mixed into the crater facies during kimberlite emplacement were recovered from the Ekati and Diavik diamond mines. Wood recovered from the Ekati "Panda" pipe, which has been dated using Rb-Sr age determination at 53.3 +/- 0.6 million years, is unique in that it exhibits extremely low vitrinite reflectance values, comparable to that of modern near-surface peats. The implication is that the wood has undergone minimal thermal or compressional alteration, thus preserving the geochemical signatures originally formed during growth. Ring width measurements representing over 100 years of climate data show congruence between multiple samples, thus enabling the development of a floating master chronology. Patterns contained in this chronology are of particular interest as the early Eocene was characterized by a period of unusual warming that has been compared to modern day climate change. Wood cellulose does not exchange atoms with its surroundings after formation, making it an ideal candidate for stable isotope analysis once it has been separated from associated whole-wood components. A robotic micromilling device was used to collect whole wood samples of latewood from annual tree rings. The α-cellulose in the samples will be isolated and analyzed for δ13C and δ18O, generating a 34-year floating chronology that can be used to reconstruct decadal scale temperature and humidity patterns. Successful application of this technique suggests that a longer Eocene chronology, using additional wood samples recovered from the Panda pipe as well as samples from neighbouring pipes in the Lac de Gras region, can be developed.

TECHNOLOGY EVALUATION REPORT: BIOLOGICAL TREATMENT OF WOOD PRESERVING SITE GROUNDWATER BY BIOTROL, INC.

EPA Science Inventory

This report provides the in-depth data analysis from the SITE Program's six-week demonstration of BioTrol's Aqueous Treatment System (BATS) at the MacGillis and Gibbs Company wood treatment facility in New Brighton, Minnesota. he pilot scale (5gpm), fixed-film biological system u...

[The influence of oil heat treatment on wood decay resistance by Fourier infrared spectrum analysis].

PubMed

Wang, Ya-Mei; Ma, Shu-Ling; Feng, Li-Qun

2014-03-01

Wood preservative treatment can improve defects of plantation wood such as easy to corrupt and moth eaten. Among them heat-treatment is not only environmental and no pollution, also can improve the corrosion resistance and dimension stability of wood. In this test Poplar and Mongolian Seoteh Pine was treated by soybean oil as heat-conducting medium, and the heat treatment wood was studied for indoor decay resistance; wood chemical components before and after treatment, the effect of heat treatment on wood decay resistance performance and main mechanism of action were analysed by Fourier infrared spectrometric. Results showed that the mass loss rate of poplar fell from 19.37% to 5% and Mongolian Seoteh Pine's fell from 8.23% to 3.15%, so oil heat treatment can effectively improve the decay resistance. Infrared spectrum analysis shows that the heat treatment made wood's hydrophilic groups such as hydroxyl groups in largely reduced, absorbing capacity decreased and the moisture of wood rotting fungi necessary was reduced; during the heat treatment wood chemical components such as cellulose, hemicellu lose were degraded, and the nutrient source of wood rotting fungi growth necessary was reduced. Wood decay fungi can grow in the wood to discredit wood is because of that wood can provide better living conditions for wood decay fungi, such as nutrients, water, oxygen, and so on. The cellulose and hemicellulose in wood is the main nutrition source of wood decay fungi. So the oil heat-treatment can reduce the cellulose, hemicellulose nutrition source of wood decay fungi so as to improve the decay resistance of wood.

Wood : adhesives

Treesearch

A.H. Conner