Experimental investigation of infiltration in soil with occurrence of preferential flow and air trapping

NASA Astrophysics Data System (ADS)

Snehota, Michal; Jelinkova, Vladimira; Sacha, Jan; Cislerova, Milena

2015-04-01

Recently, a number of infiltration experiments have not proved the validity of standard Richards' theory of the flow in soils with wide pore size distribution. Water flow in such soils under near-saturated conditions often exhibits preferential flow and temporal instability of the saturated hydraulic conductivity. An intact sample of coarse sandy loam from Cambisol series containing naturally developed vertically connected macropore was investigated during recurrent ponding infiltration (RPI) experiments conducted during period of 30 hours. RPI experiment consisted of two ponded infiltration runs, each followed by free gravitational draining of the sample. Three-dimensional neutron tomography (NT) image of the dry sample was acquired before the infiltration begun. The dynamics of the wetting front advancement was investigated by a sequence of neutron radiography (NR) images. Analysis of NR showed that water front moved preferentially through the macropore at the approximate speed of 2 mm/sec, which was significantly faster pace than the 0.3 mm/sec wetting advancement in the surrounding soil matrix. After the water started to flow out of the sample, changes in the local water content distribution were evaluated quantitatively by subtracting the NT image of the dry sample from subsequent tomography images. As a next stage, the experiment was repeated on a composed sample packed of ceramic and coarse sand. Series of infiltration runs was conducted in the sample with different initial water contents. The neutron tomography data quantitatively showed that both in natural soil sample containing the macropore and in the composed sample air was gradually transported from the region of fine soil matrix to the macropores or to the coarser material. The accumulation of the air bubbles in the large pores affected the hydraulic conductivity of the sample reducing it up to 50% of the initial value. This supports the hypothesis on strong influence of entrapped air amount and spatial distribution on infiltration into heterogeneous soils. The research was supported by the Czech Science Foundation Project No. 14-03691S.

Infiltration behaviour of elemental mercury DNAPL in fully and partially water saturated porous media.

PubMed

D'Aniello, Andrea; Hartog, Niels; Sweijen, Thomas; Pianese, Domenico

2018-02-01

Mercury is a contaminant of global concern due to its harmful effects on human health and for the detrimental consequences of its release in the environment. Sources of liquid elemental mercury are usually anthropogenic, such as chlor-alkali plants. To date insight into the infiltration behaviour of liquid elemental mercury in the subsurface is lacking, although this is critical for assessing both characterization and remediation approaches for mercury DNAPL contaminated sites. Therefore, in this study the infiltration behaviour of elemental mercury in fully and partially water saturated systems was investigated using column experiments. The properties affecting the constitutive relations governing the infiltration behaviour of liquid Hg 0 , and PCE for comparison, were determined using P c (S) experiments with different granular porous media (glass beads and sands) for different two- and three-phase configurations. Results showed that, in water saturated porous media, elemental mercury, as PCE, acted as a non-wetting fluid. The required entry head for elemental mercury was higher (from about 5 to 7 times). However, due to the almost tenfold higher density of mercury, the required NAPL entry heads of 6.19cm and 12.51cm for mercury to infiltrate were 37.5% to 20.7% lower than for PCE for the same porous media. Although Leverett scaling was able to reproduce the natural tendency of Hg 0 to be more prone than PCE to infiltrate in water saturated porous media, it considerably underestimated Hg 0 infiltration capacity in comparison with the experimental results. In the partially water saturated system, in contrast with PCE, elemental mercury also acted as a nonwetting fluid, therefore having to overcome an entry head to infiltrate. The required Hg 0 entry heads (10.45 and 15.74cm) were considerably higher (68.9% and 25.8%) than for the water saturated porous systems. Furthermore, in the partially water saturated systems, experiments showed that elemental mercury displaced both air and water, depending on the initial water distribution within the pores. This indicates that the conventional wettability hierarchy, in which the NAPL has an intermediate wetting state between the air and the water phases, is not valid for liquid elemental mercury. Therefore, for future modelling of elemental mercury DNAPL infiltration behaviour in variably water saturated porous media, a different formulation of the governing constitutive relations will be required. Copyright © 2018 Elsevier B.V. All rights reserved.

Infiltration into Fractured Bedrock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salve, Rohit; Ghezzehei, Teamrat A.; Jones, Robert

One potential consequence of global climate change and rapid changes in land use is an increased risk of flooding. Proper understanding of floodwater infiltration thus becomes a crucial component of our preparedness to meet the environmental challenges of projected climate change. In this paper, we present the results of a long-term infiltration experiment performed on fractured ash flow tuff. Water was released from a 3 x 4 m{sup 2} infiltration plot (divided into 12 square subplots) with a head of {approx}0.04 m, over a period of {approx}800 days. This experiment revealed peculiar infiltration patterns not amenable to current infiltration models,more » which were originally developed for infiltration into soils over a short duration. In particular, we observed that in part of the infiltration plot, the infiltration rate abruptly increased a few weeks into the infiltration tests. We suggest that these anomalies result from increases in fracture permeability during infiltration, which may be caused by swelling of clay fillings and/or erosion of infill debris. Interaction of the infiltration water with subsurface natural cavities (lithophysal cavities) could also contribute to such anomalies. This paper provides a conceptual model that partly describes the observed infiltration patterns in fractured rock and highlights some of the pitfalls associated with direct extension of soil infiltration models to fractured rock over a long period.« less

SP Response to a Line Source Infiltration for Characterizing the Vadose Zone: Forward Modeling and Inversion

NASA Astrophysics Data System (ADS)

Sailhac, P.

2004-05-01

Field estimation of soil water flux has direct application for water resource management. Standard hydrologic methods like tensiometry or TDR are often difficult to apply because of the heterogeneity of the subsurface, and non invasive tools like ERT, NMR or GPR are limited to the estimation of the water content. Electrical Streaming Potential (SP) monitoring can provide a cost-effective tool to help estimate the nature of the hydraulic transfers (infiltration or evaporation) in the vadose zone. Indeed this technique has improved during the last decade and has been shown to be a useful tool for quantitative groundwater flow characterization (see the poster of Marquis et al. for a review). We now account for our latest development on the possibility of using SP for estimating hydraulic parameters of unsaturated soils from in situ SP measurements during infiltration experiments. The proposed method consists in SP profiling perpendicularly to a line source of steady-state infiltration. Analytic expressions for the forward modeling show a sensitivity to six parameters: the electrokinetic coupling parameter at saturation CS, the soil sorptive number α , the ratio of the constant source strength to the hydraulic conductivity at saturation q/KS, the soil effective water saturation prior to the infiltration experiment Se0, Mualem parameter m, and Archie law exponent n. In applications, all these parameters could be constrained by inverting electrokinetic data obtained during a series of infiltration experiments with varying source strength q.

Laboratory-based geoelectric monitoring of water infiltration in consolidated ground

NASA Astrophysics Data System (ADS)

Yang, Lining; Sun, Qiang; Yang, Haiping

2018-04-01

Infiltration usually plays a significant role in construction failures and transfer of contaminants. Therefore, it is very important to monitor underground water migration. In this study, a soil infiltration experiment was carried out using an indoor model test. The water infiltration characteristics were recorded and analyzed based on the response of the geoelectric field, including the primary field potential, self-potential, excitation current and apparent resistivity. The phreatic water surface and the infiltration velocity were determined. The inversion results were compared with direct observations. The results showed that the changes in the geoelectric field parameters explain the principles of groundwater flow. The infiltration velocity and the phreatic surface can be determined based on the primary field potential response and the excitation current. When the phreatic surface reached the location of the electrodes, the primary field potential and self-potential decreased rapidly whereas the excitation current increased rapidly. The height of the phreatic surface and the infiltration time exhibited a linear relationship for both the observation data and the calculations of the excitation current. The apparent resistivity described the infiltration status in the soil and tracked the phreatic surface accurately.

The influence of wetting dynamics on the residual air distribution

NASA Astrophysics Data System (ADS)

Sacha, J.; Snehota, M.; Trtik, P.; Vontobel, P.

2016-12-01

The amount and distribution of the residual air during the infiltration into a porous soil system has a strong influence on the infiltration rate. Concurrently, the amount of residual air is dependent on the wetting dynamics. In the presented study, two experiments were conducted on the same sample. The first experiment was performed under the constant water level condition (CWL) and the second under the constant water flux condition (CWF) at the top of the sample. The sample that composed of coarse and medium coarse fractions of sand and fine porous ceramics was packed into the quartz glass columns of the inner diameter of 29 mm. The coarse sand represented a highly conductive region connected from the top to the bottom of the sample with the exception of three low (2-3 mm) separation layers made up of the medium coarse sand. Three discs of fine ceramic formed slow flow regions. Infiltration experiments were monitored by neutron radiography on two different beamlines to produce two-dimensional (2D) projections. The CWL experiment was monitored by NEUTRA station with an acquisition time of 16 seconds per projection and the CWF experiment was visualized at BOA station with an acquisition time of 0.25 seconds per projection. Both stations are located at the Paul Scherrer Institut, Switzerland. The acquired radiograms of the dry sample were subtracted from all subsequent radiograms to determine the water thickness in projections. From series of corrected radiograms taken at the different angles three-dimensional (3D) image was reconstructed for steady state part of the experiment CWL and for entire experiment CWF. Then the series of 3D images mapped the wetting of the porous system over the corresponding phase of infiltration process. The results showed a faster steady state infiltration rate during the CWL. In this case, the air was mostly pushed out from the sample by moving wetting front. On the contrary, during the CWF the water infiltrated into the fine ceramics first and then into the medium coarse sand attracted by stronger capillary forces in comparison to the coarse sand. Due to this effect a significant amount of air was trapped in preferential pathways, and consequently blocking the water flow. The presence of medium coarse sand regions had a crucial impact on the water flow and amount of air trapping.

Fate and Transport of Bacteriophage (MS2 and PRD1) During Field-Scale Infiltration at a Research Site in Los Angeles County, CA

NASA Astrophysics Data System (ADS)

Anders, R.; Chrysikopoulos, C. V.

2003-12-01

As the use of tertiary-treated municipal wastewater (recycled water) for replenishment purposes continues to increase, provisions are being established to protect ground-water resources by ensuring that adequate soil-retention time and distance requirements are met for pathogen removal. However, many of the factors controlling virus fate and transport (e.g. hydraulic conditions, ground-water chemistry, and sediment mineralogy) are interrelated and poorly understood. Therefore, conducting field-scale experiments using surrogates for human enteric viruses at an actual recharge basin that uses recycled water may represent the best approach for establishing adequate setback requirements. Three field-scale infiltration experiments were conducted at such a basin using bacterial viruses (bacteriophage) MS2 and PRD1 as surrogates for human viruses, bromide as a conservative tracer, and recycled water. The specific research site consists of a test basin constructed adjacent to a large recharge facility (spreading grounds) located in the Montebello Forebay of Los Angeles County, California. The soil beneath the test basin is predominantly medium to coarse, moderately sorted, grayish-brown sand. The first experiment was conducted over a 2-day period to determine the feasibility of conducting field-scale infiltration experiments using recycled water seeded with high concentrations of bacteriophage and bromide as tracers. Based on the results of the first experiment, a second experiment was completed when similar hydraulic conditions existed at the test basin. The third infiltration experiment was conducted to confirm the results obtained from the second experiment. Data were obtained for samples collected during the second and third field-scale infiltration experiments from the test basin itself and from depths of 0.3, 0.6, 1.0, 1.5, 3.0, and 7.6 m below the bottom of the test basin. These field-scale tracer experiments indicate bacteriophage are attenuated by removal and (or) inactivation during subsurface transport. To simulate the transport and fate of viruses during infiltration, a nonlinear least-squares regression program was used to fit a one-dimensional virus transport model to the experimental data. The model simulates virus transport in homogeneous, saturated porous media with first-order adsorption (or filtration) and inactivation. Furthermore, the model obtains a semi-analytical solution for the special case of a broad pulse and time-dependent source concentration using the principle of superposition. The fitted parameters include the clogging and declogging rate constants and the inactivation constants of suspended and adsorbed viruses. Preliminary results show a reasonable match of the first arrival of bacteriophage and bromide.

Field-Measured Infiltration Properties of Mojave Desert Soils

NASA Astrophysics Data System (ADS)

Perkins, K. S.; Nimmo, J. R.; Winfield, K. A.; Schmidt, K. M.; Miller, D. M.; Stock, J. D.; Singha, K.

2005-12-01

Characteristics typical of alluvial desert soils, such as depositional stratification, desert pavement, biotic crusts, and vesicular horizons strongly influence soil moisture and its variability. Knowledge of infiltration capacity, water retention, and unsaturated hydraulic conductivity is central to the assessment of water availability to plants and animals after infiltration events. These hydraulic parameters are directly related to the degree of soil development. The frequency and magnitude of storm events in conjunction with degree of soil development also affect runoff and erosion. Our purpose is to examine field soil-water behavior and determine unsaturated hydraulic properties needed for large-scale modeling of soil moisture. The results of this study will be used in conjunction with surficial geologic mapping of the Mojave Desert in evaluations of ecological habitat quality. We conducted infiltration/redistribution experiments on three different-aged deposits in the Mojave National Preserve: (1) recently deposited wash sediments, (2) a soil of early Holocene age, and (3) a highly developed soil of late Pleistocene age. In each experiment we ponded water in a 1-m-diameter infiltration ring for 2.3 hr. For several weeks we monitored water content and matric pressure to depths of 1.5 m, and distances of 6 m from the infiltration ring. Measuring techniques included surface electrical resistance tomography, dielectric-constant probes, heat-dissipation probes, and tensiometers. Analysis of the subsurface measurements using an instantaneous-profile technique gives the retention and K properties that will be used in predictive modeling. In each experiment the infiltration rate was nearly constant in time, with infiltration capacity 4 times greater in the youngest than in the oldest soil. Average infiltration flux densities within the ring during the period of ponding were 0.80 m/hr in the active wash, 0.45 m/hr in the Holocene soil, and 0.21 m/hr in the Pleistocene soil. All three deposits have significant gravel (30-70% within the uppermost 1.5 m) with the percentage of silt and clay increasing with deposit age. The low infiltration capacity in the oldest soil is consistent with the presence of the more highly developed vesicular horizon and accumulation of illuvial silt. Depositional stratification in the active wash did not impede downward flow to the same degree as in the early Holocene-age soil, which has some soil horizon development and sparse biotic crust. Infiltrated water spread laterally to at least 1 m beyond the ring perimeter at all sites; the presence of a buried clay-rich horizon in the active wash enhanced spreading at depth to 2 m.

Effects of water collection and mulching combinations on water infiltration and consumption in a semiarid rainfed orchard

NASA Astrophysics Data System (ADS)

Li, Hongchen; Zhao, Xining; Gao, Xiaodong; Ren, Kemeng; Wu, Pute

2018-03-01

Soil water and its efficient use are critical to sustainable productivity of rainfed orchards under the context of climate change in water-limited areas. Here, we combined micro-catchments for collecting hillslope runoff, named fish-scale pits, with mulches to examine water infiltration and water consumption of fruit trees using in situ soil moisture monitoring, the micro-lysimeter and sap flow methods via a two-year experiment in a rainfed jujube orchard on China's Loess Plateau. This experiment included four treatments: fish-scale pit with branch mulching (FB), fish-scale pit with straw mulching (FS), fish-scale pit without mulching (F), and bare land treatment (CK). The results showed that only about 50% of the rainfall infiltrated the soil for CK during the 2014 and 2015 growing seasons. The fish-scale pit without mulching experienced significantly increased rainfall infiltration by 41.38 and 27.30%, respectively, but also increased evaporation by 42.28 and 65.59%, respectively, compared to CK during the two growing seasons. The jujube transpiration significantly increased by 45.64-53.10% over CK, and the evaporation decreased by 42.47-53.50% when fish-scale pits were mulched with branches or straw. Taken together, the results show that the fish-scale pits and mulching combinations efficiently increased rainfall infiltration and jujube evapotranspiration in the experimental jujube orchard. The findings here provide an insight into the field water management for hillslope orchards in water-limited regions.

Impact of climate variations on Managed Aquifer Recharge infiltration basins.

NASA Astrophysics Data System (ADS)

Barquero, Felix; Stefan, Catalin

2017-04-01

KEYWORDS: Managed Aquifer Recharge, field scale infiltration unit, climatic conditions, numerical model Managed Aquifer Recharge (MAR) is a technique that is gaining more attention as a sustainable alternative for areas where water scarcity is increasing. Main concept relies on facilitating the vertical infiltration of a source of fresh water (river water, rainwater, reclaimed water, etc). The groundwater acts as storage of water for further use in the future, for example in times of water scarcity. In some MAR types the soil itself can be used even as a filter for the removal of specific organic and inorganic compounds. In order to promote the benefits of MAR in different zones of the globe with variable climate conditions, including the effects of climate change, a numerical model (HYDRUS 2D/3D) is being set up. Coupled with the model a field-scale rapid infiltration unit (4m x 5m x 1.5m) was constructed with the capacity to log different MAR key parameters in the soil (tension, water content, temperature and electrical conductivity) in space and time. These data will feed the model for its calibration using specific hydrogeological characteristics of the packing material and hydraulic characteristics of the infiltrated fluid. The unit is located in the city of Pirna (German), 200 m north from the Elbe River where the groundwater level varies seasonally between 6 and 9 m below the ground surface. Together with the field scale rapid infiltration unit, a set of multi-parametric sensors (measuring in time: water stage, electrical conductivity, dissolved oxygen and temperature) in six monitoring wells, located on the basin surroundings, were installed. The purpose of these sensors is to estimate, via tracer experiments, the time that the infiltrated water needed to reach the groundwater and the flow speed in which it travelled once it reached the saturated zone. Once calibrated, the model will be able to estimate the flow behaviour under variable climate conditions (temperature, precipitation and evaporation), representative for different climatic zones in the globe. The simulation results of the different climate models reported by the IPCC will also be considered for critical zones where fresh water availability will decrease considerably. In the field, the first results confirmed the arrival, after 14 days of travel time, of the infiltrated river water front to the monitoring wells located next to the infiltration unit. Further tracer experiments have to be performed in order to catch a stronger breakthrough curve in more than one observation point. Interesting open questions arise from the data stored in the trench sensors. How the change of the travel velocity depends on different external parameters like time of operation, cyclic wetting and drying regime and temperature, will be analysed together with the results of the ongoing experiments.

Vadose zone dynamics governing snowmelt infiltration and groundwater recharge in a seasonally frozen, semi-arid landscape

NASA Astrophysics Data System (ADS)

Mohammed, A.; LeBlanc, F.; Cey, E. E.; Hayashi, M.

2016-12-01

Snowmelt infiltration and vadose zone fluxes in seasonally frozen soils are strongly affected by meteorological and soil moisture dynamics occurring during the preceding fall and winter, and complex processes controlling soil hydraulic and thermal regimes. In order to predict their effects on hydrologic processes such as run-off generation, groundwater recharge and plant-water availability in cold regions, an improved understanding of the mechanisms governing coupled water and heat fluxes in the unsaturated zone is needed. Field and laboratory studies were conducted to investigate snowmelt infiltration and groundwater recharge through partially frozen ground over a range of climate and soil conditions in the Canadian Prairies. Meteorological and subsurface field measurements at three sites were combined with laboratory infiltration experiments on frozen undisturbed soil-columns to provide insights into the hydraulic and thermal processes governing water movement. Analysis reveals that antecedent moisture content and thermal profiles both strongly affect subsurface dynamics during infiltration of snowmelt. Preferential flow is also a critical parameter, as both thermal and hydraulic responses were observed at depth prior to complete ground thaw in the field; as well as drainage outflow from the frozen soil column experiments under certain conditions. Results indicate that both diffuse (matrix) and preferential (macropore) flow play significant roles in the infiltration and redistribution of snowmelt water under frozen soil conditions, and shallow groundwater recharge. This study highlights the critical subsurface factors and processes that control infiltration and groundwater recharge in these seasonally frozen landscapes.

Applying Reactive Barrier Technology to Enhance Microbially-mediated Denitrification during Managed Aquifer Recharge

NASA Astrophysics Data System (ADS)

Beganskas, S.; Weir, W. B.; Harmon, R. E.; Gorski, G.; Fisher, A. T.; Saltikov, C.; Young, K. S.; Runneals, D.; Teo, E. K.; Stoneburner, B.; Hernandez, J.

2015-12-01

We are running field experiments to observe and quantify microbially-mediated water quality improvement via denitrification during infiltration in the shallow subsurface. Nitrate is a pervasive groundwater contaminant, and nitrate removal through denitrification can occur during infiltration in natural and anthropogenic systems, including during managed aquifer recharge (MAR). The rate of denitrification can vary depending on factors such as infiltration rate; previous work suggests that denitrification rates can increase monotonically with infiltration rates until reaching a critical threshold. We are performing controlled field tests of variables that affect denitrification rate, including sampling to link water chemistry changes to microbial ecology and activity. This study explores how microbial activity and denitrification rates respond to different infiltration rates and the presence or absence of a reactive material (wood chips, a carbon source). We are conducting four two-week-long tests, each under different conditions. For each test, we measure bulk infiltration rate (the sum of lateral and vertical infiltration), vertical infiltration rate using heat as a tracer, and water level. We collect surface and subsurface water samples daily, and we collect soil samples at the start and end of each test. For each water sample, we are measuring NO3-, NO2-, NH3, DOC, and N and O isotopes in nitrate. Soil samples will be tested for grain size, total C/N, and the presence of microbiological genes associated with denitrification. These results will expand our knowledge of the conditions under which denitrification occurs by implicating specific microorganisms and physical infiltration parameters. Our design has the potential for additional experimentation with variables that impact water chemistry during infiltration. This study has broad applications for designing MAR systems that effectively improve water supply and water quality.

Modelling of percolation rate of stormwater from underground infiltration systems.

PubMed

Burszta-Adamiak, Ewa; Lomotowski, Janusz

2013-01-01

Underground or surface stormwater storage tank systems that enable the infiltration of water into the ground are basic elements used in Sustainable Urban Drainage Systems (SUDS). So far, the design methods for such facilities have not taken into account the phenomenon of ground clogging during stormwater infiltration. Top layer sealing of the filter bed influences the infiltration rate of water into the ground. This study presents an original mathematical model describing changes in the infiltration rate variability in the phases of filling and emptying the storage and infiltration tank systems, which enables the determination of the degree of top ground layer clogging. The input data for modelling were obtained from studies conducted on experimental sites on objects constructed on a semi-technological scale. The experiment conducted has proven that the application of the model developed for the phase of water infiltration enables us to estimate the degree of module clogging. However, this method is more suitable for reservoirs embedded in more permeable soils than for those located in cohesive soils.

Investigations of infiltration processes from flooded areas by column experiments

NASA Astrophysics Data System (ADS)

Mohrlok, U.; Bethge, E.; Golalipour, A.

2009-04-01

In case of inundation of flood plains during flood events there is an increased risk of groundwater contamination due to infiltration of increasingly polluted river water. Specifically in densely populated regions, this groundwater may be used as source for drinking water supply. For the evaluation of this a detailed quantitative understanding of the infiltration processes under such conditions is required. In this context the infiltration related to a flood event can be described by three phases. The first phase is defined by the saturation of the unsaturated soils. Within the second phase infiltration takes place under almost saturated conditions determined by the hydraulic load of the flood water level. The drainage of the soils due to falling groundwater table is characterizing the third phase. Investigations by soil columns gave a detailed insight into the infiltration processes caused by flooding. Inflow at the soil top was established by a fixed water table fed by a Mariotte bottle. Free outflow and a groundwater table were used as lower boundary condition. Inflow and outflow volume were monitored. The evolution of the matrix pressure was observed by micro-tensiometers installed at several depths within the soil column. The flow processes during phase one and two were characterized by a tracer test. Some of the experiments were repeated in order to study the influence of preliminary events. Main results were a difference in infiltration due to the lower boundary condition with regard to inflow rate, outflow dynamics and matrix pressure evolution which is directly related to the water content evolution. Further, the influence of preliminary events was different for the different boundary conditions. A replacement of pre-event water could be observed which was confirmed by volume balances calculated for the infiltration experiments. Although these water balances were almost closed significant dynamics of the matrix pressure remained in soil column in the drainage phase. The detailed analysis of the hydraulic conditions and the flow rates provided an estimate of the unsaturated hydraulic conductivity that could be related to the degree of saturation. Numerical simulations were not able to reproduce these conditions. These results could be used to estimate time scales of flow and solute transport in soils caused by flood events.

Infiltration on mountain slopes: a comparison of three environments.

Treesearch

Carol P. Harden*; P. Delmas Scruggs

2003-01-01

Water is well established as a major driver of the geomorphic change that eventually reduces mountains to lower relief landscapes. Nonetheless, within the altitudinal limits of continuous vegetation in humid climates, water is also an essential factor in slope stability. In this paper, we present results from field experiments to determine infiltration rates at...

Non-isothermal infiltration and tracer transport experiments on large soil columns

NASA Astrophysics Data System (ADS)

Sobotkova, Martina; Snehota, Michal; Cejkova, Eva; Tesar, Miroslav

2016-04-01

Isothermal and non-isothermal infiltration experiments were carried out in the laboratory on large undisturbed soil columns (19 cm in diameter, 25 cm high) taken at the experimental catchments Roklan (Sumava Mountains, Czech Republic) and Uhlirska (Jizera Mountains, Czech republic). The aim of the study was twofold. The first goal was to obtain water flow and heat transport data for indirect parameter estimation of thermal and hydraulic properties of soils from two sites by inverse modelling. The second aim was to investigate the extent of impact of the temperature on saturated hydraulic conductivity (Ksat) and dispersity of solute transport. The temperature of infiltrating water in isothermal experiment (20 °C) was equal to the initial temperature of the sample. For non-isothermal experiment water temperature was 5°C, while the initial temperature of the sample was 20°C as in previous case. The experiment was started by flooding the sample surface. Then water level was maintained at constant level throughout the infiltration run using the optical sensor and peristaltic pump. Concentration pulse of deuterium was applied at the top of the soil sample, during the steady state flow. Initial pressure head in the sample was close to field capacity. Two tensiometers and two temperature sensors were inserted in the soil sample in two depths (9 and 15 cm below the top of the sample). Two additional temperature sensors monitored the temperature entering and leaving the samples. Water drained freely through the perforated plate at the bottom of sample by gravity. Inflow and outflow water flux densities, water pressure heads and soil temperatures were monitored continuously during experiments. Effluent was sampled in regular time intervals and samples were analysed for deuterium concentrations by laser spectroscopy to develop breakthrough curves. The outcome of experiments are the series of measured water fluxes, pressure heads and temperatures ready for inverse modelling by dual permeability. The saturated hydraulic conductivity of soil columns was higher in the case of higher temperature of flowing water. The change was however not proportional to Ksat change induced by temperature change of viscosity only.

Does drought alter hydrological functions in forest soils?

NASA Astrophysics Data System (ADS)

Gimbel, Katharina F.; Puhlmann, Heike; Weiler, Markus

2016-04-01

Climate change is expected to impact the water cycle and severely affect precipitation patterns across central Europe and in other parts of the world, leading to more frequent and severe droughts. Usually when projecting drought impacts on hydrological systems, it is assumed that system properties, like soil properties, remain stable and will not be affected by drought events. To study if this assumption is appropriate, we address the effects of drought on the infiltration behavior of forest soils using dye tracer experiments on six sites in three regions across Germany, which were forced into drought conditions. The sites cover clayey-, loamy- and sandy-textured soils. In each region, we compared a deciduous and a coniferous forest stand to address differences between the main tree species. The results of the dye tracer experiments show clear evidence for changes in infiltration behavior at the sites. The infiltration changed at the clayey plots from regular and homogeneous flow to fast preferential flow. Similar behavior was observed at the loamy plots, where large areas in the upper layers remained dry, displaying signs of strong water repellency. This was confirmed by water drop penetration time (WDPT) tests, which revealed, in all except one plot, moderate to severe water repellency. Water repellency was also accountable for the change of regular infiltration to fingered flow in the sandy soils. The results of this study suggest that the drought history or, more generally, the climatic conditions of a soil in the past are more important than the actual antecedent soil moisture status regarding hydrophobicity and infiltration behavior; furthermore, drought effects on infiltration need to be considered in hydrological models to obtain realistic predictions concerning water quality and quantity in runoff and groundwater recharge.

Combining sprinkling experiments and superconducting gravimetry in the field: a qualitative approach to identify dominant infiltration patterns

NASA Astrophysics Data System (ADS)

Reich, Marvin; Mikolaj, Michal; Blume, Theresa; Güntner, Andreas

2017-04-01

Hydrological process research at the plot to catchment scale commonly involves invasive field methods, leading to a large amount of point data. A promising alternative, which gained increasing interest in the hydrological community over the last years, is gravimetry. The combination of its non-invasive and integrative nature opens up new possibilities to approach hydrological process research. In this study we combine a field-scale sprinkling experiment with continuous superconducting gravity (SG) measurements. The experimental design consists of 8 sprinkler units, arranged symmetrically within a radius of about ten meters around an iGrav (SG) in a field enclosure. The gravity signal of the infiltrating sprinkling water is analyzed using a simple 3D water mass distribution model. We first conducted a number of virtual sprinkling experiments resulting in different idealized infiltration patterns and determined the pattern specific gravity response. In a next step we determined which combination of idealized infiltration patterns was able to reproduce the gravity response of our real-world experiment at the Wettzell Observatory (Germany). This process hypothesis is then evaluated with measured point-scale soil moisture responses and the results of the time-lapse electric resistivity survey which was carried out during the sprinkling experiment. This study demonstrates that a controlled sprinkling experiment around a gravimeter in combination with a simple infiltration model is sufficient to identify subsurface flow patterns and thus the dominant infiltration processes. As gravimeters become more portable and can actually be deployed in the field, their combination with sprinkling experiments as shown here constitutes a promising possibility to investigate hydrological processes in a non-invasive way.

Quantifying mobile and immobile zones during simulated stormwater infiltration through a new permeable pavement material.

PubMed

Bentarzi, Y; Ghenaim, A; Terfous, A; Wanko, A; Poulet, J B

2015-01-01

We have designed a new eco-material for use in permeable pavements in view to ensuring the sustainable management of stormwater in urban areas. The specific characteristic of this material is that it allows the infiltration of rainfall, storing the infiltrated water and trapping the pollutants carried by runoff such as engine oil and heavy metals. This new material is composed of a mixture of crushed concrete , resulting from inert construction waste, and organic material (compost). We performed tracing experiments in view to monitor the flow of the water within this material in order to study its hydrodynamics under heavy rainfall (rain with a return period of 10 years). The experimental results revealed preferential flows due to the heterogeneity of the material and liable to act as a major vector for the mobility of the pollutants transported within the material by stormwater. The work presented in this article consists in quantifying these preferential flows by determining their water contents in mobile (θm) and immobile (θim) water during infiltration. To do this, we used the (NON-EQUILIBRIUM Convection-Dispersion Equation) model, in order to evaluate mobile and stagnant zones in the framework of tracing experiments.

Effect of rainfall infiltration into unsaturated soil using soil column

NASA Astrophysics Data System (ADS)

Ibrahim, A.; Mukhlisin, M.; Jaafar, O.

2018-02-01

Rainfall especially in tropical region caused infiltration to the soil slope. The infiltration may change pore water pressure or matric suction of the soil. The event of rainfall infiltration into soil is a complex mechanism. Therefore, the main objectives of this research paper is to study the influence of rainfall intensity and duration that changed pore water pressure to soil. There are two types of soils used in this study; forest soil and kaolin. Soil column apparatus is used for experiments. Rainfall were applied to the soil and result for 3, 6, 12, 24, 72, 120 and 168 hours were retrieved. Result shows that for the both types of soil, the negative pore water pressures were increased during wetting process and gradually decreased towards drying process. The results also show that pore water pressure at top part was increased greatly as the wetting process started compared to the middle and bottom part of the column.

Effects of white grubs on soil water infiltration.

PubMed

Romero-López, A A; Rodríguez-Palacios, E; Alarcón-Gutiérrez, E; Geissert, D; Barois, I

2015-04-01

Water infiltration rates k were measured in mesocosms with soil and "white grubs" of Ancognatha falsa (Arrow) (Coleoptera: Melolonthidae). Three third instars of A. falsa and three adult earthworms Pontoscolex corethrurus were selected, weighted, and introduced into the mesocosms setting three treatments: soil + A. falsa, soil + P. corethrurus, and control (soil without any macroorganism). The experiment had a completely random design with four replicates per treatment (n = 4). The infiltration rates of soil matrix were assessed in each mesocosms with a minidisk tension infiltrometer. Six measurements were made along the experiment. Results showed that larvae of A. falsa promoted a higher water infiltration in the soil, compared to the control. On day 7, k values were similar among treatments, but k values after 28 days and up to 100 days were much higher in the A. falsa treatment (k = 0.00025 cm s(-1)) if compared to control (k = 0.00011 cm s(-1)) and P. corethrurus (k = 0.00008 cm s(-1)) treatments. The k values were significantly higher in the presence of larvae of A. falsa compared to the control and P. corethrurus treatments. The larvae of A. falsa are potential candidates for new assays on soil water infiltration with different tensions to evaluate the role of pores and holes created by the larvae on soils.

Protoplast Volume:Water Potential Relationship and Bound Water Fraction in Spinach Leaves 1

PubMed Central

Santakumari, Mane; Berkowitz, Gerald A.

1989-01-01

Methods used to estimate the (nonosmotic) bound water fraction (BWF) (i.e. apoplast water) of spinach (Spinacia oleracea L.) leaves were evaluated. Studies using three different methods of pressure/volume (P/V) curve construction all resulted in a similar calculation of BWF; approximately 40%. The theoretically derived BWF, and the water potential (Ψw)/relative water content relationship established from P/V curves were used to establish the relationship between protoplast (i.e. symplast) volume and Ψw. Another method of establishing the protoplast volume/Ψw relationship in spinach leaves was compared with the results from P/V curve experiments. This second technique involved the vacuum infiltration of solutions at a range of osmotic potentials into discs cut from spinach leaves. These solutions contained radioactively labeled H2O and sorbitol. This dual label infiltration technique allowed for simultaneous measurement of the total and apoplast volumes in leaf tissue; the difference yielded the protoplast volume. The dual label infiltration experiments and the P/V curve constructions both showed that below −1 megapascals, protoplast volume decreases sharply with decreasing water potential; with 50% reduction in protoplast volume occurring at −1.8 megapascals leaf water potential. PMID:16666983

Estimation of Infiltration Parameters and the Irrigation Coefficients with the Surface Irrigation Advance Distance

PubMed Central

Beibei, Zhou; Quanjiu, Wang; Shuai, Tan

2014-01-01

A theory based on Manning roughness equation, Philip equation and water balance equation was developed which only employed the advance distance in the calculation of the infiltration parameters and irrigation coefficients in both the border irrigation and the surge irrigation. The improved procedure was validated with both the border irrigation and surge irrigation experiments. The main results are shown as follows. Infiltration parameters of the Philip equation could be calculated accurately only using water advance distance in the irrigation process comparing to the experimental data. With the calculated parameters and the water balance equation, the irrigation coefficients were also estimated. The water advance velocity should be measured at about 0.5 m to 1.0 m far from the water advance in the experimental corn fields. PMID:25061664

Investigating controls on denitrification rates during managed aquifer recharge: Field studies of infiltration

NASA Astrophysics Data System (ADS)

Beganskas, S.; Gorski, G.; Fisher, A. T.; Weir, W. B.; Schmidt, C. M.; Saltikov, C.; Stoneburner, B.; Hernandez, J.; Harmon, R. E.; Weathers, T. S.

2016-12-01

We have designed field experiments to observe and quantify water quality improvement during infiltration in the shallow subsurface, as part of managed aquifer recharge (MAR). We are exploring how microbial diversity and denitrification rate respond to different infiltration rates and the presence or absence of carbon-rich reactive materials (woodchips or biochar). In 2015, we conducted a series of two-week-long field infiltration tests, and in 2016 we are running tests at a new site. For each test, nitrate-rich water (20-25 ppm NO3-N) was continuously applied to 1-m square plots instrumented to measure infiltration rates and sample subsurface water at multiple depths. Soil samples were collected before and after each test to assess microbial diversity. In 2015, we observed infiltration rates of 4-18 m/d, consistent with very sandy soils at our field site. All water samples had >20 ppm DOC, indicating that denitrification was unlikely carbon-limited. There was a net increase in DOC in fluids sampled below woodchips, but no change in DOC in samples from un-amended native soil. Up to 20% of NO3- was removed below woodchips on days with infiltration rates below 15 m/d. Nitrate removal was not observed in native soil, even though infiltration rates were considerably lower, 4 m/d. Isotopic analyses indicate that denitrification is likely the mechanism for nitrate removal. Genomic sequencing of soil microbes shows that microbial populations' relative abundance shifted significantly due to infiltration; further analyses are underway. Our results suggest that rapid infiltration can lead to oxic conditions unfavorable for denitrification, and that a carbon-rich reactive material (woodchips) may stimulate microbially-mediated denitrification. Our experimental design is a novel way to examine factors that impact water quality during infiltration. Nitrate, a pervasive groundwater contaminant, can be removed via denitrification during MAR under some conditions, depending on infiltration rate, available carbon, and substrate material. Our work has applications for designing MAR systems that effectively improve water supply and water quality.

Column Experiments Investigating Wetting and Drying of Soil and Consumption of Organic Contaminants for Managed Aquifer Recharge

NASA Astrophysics Data System (ADS)

Silver, M.; Schueth, C.; Wefer-Roehl, A.; Kuebeck, C.

2014-12-01

The EU FP7 project MARSOL seeks to address water scarcity challenges in arid regions. Within this framework, we conduct a series of experiments to evaluate the potential for water quality improvement and changes in hydraulic conductivity when managed aquifer recharge (MAR) is performed by infiltrating treated wastewater in soils that do not have high potential for sorption. For example, in the Attica (Athens and vicinity) region of Greece, the bedrock is mostly marble, resulting in calcite-rich soils that present little potential for sorption of contaminants to mineral surfaces. This leaves consumption of organic contaminants by microbes as the critical mechanism for water quality improvement, when treated wastewater is infiltrated through such soils. In order to enhance the potential for contaminant consumption by aerobic bacteria in a way that would be realistic to later perform in an infiltration basin, we conduct experiments using a series of wetting and drying cycles. The experimental setup consists of 90-cm long soil columns, fitted with oxygen sensors, time-domain reflectometry sensors (to measure moisture content), sampling ports, oxidation-reduction probes, and head observation tubes. We use the data collected from these sensors and features of the experimental setup to answer the following questions: 1. Does hydraulic conductivity change, from formation of a biofilm or dissolution of calcite (or both)? 2. Are organic contaminants consumed? 3. What effect do wetting and drying cycles have on consumption of organic contaminants? 4. How long can infiltration of treated wastewater last, before oxygen is consumed and conditions become reducing? These questions are investigated by observing the hydraulic head and outflow, performing tracer tests, taking samples from the sampling ports and outflow for chemical analyses, and measuring moisture content and oxygen concentration, in the course of performing multiple wetting and drying cycles. These column experiments will be used to evaluate the potential for new MAR applications in areas facing water scarcity challenges. In the future the experiments will be expanded to test multiple soils and optimize both the soil type and infiltration patterns in order to best obtain water quality improvements through MAR.

Importance of mechanical disaggregation in chemical weathering in a cold alpine environment, San Juan Mountains, Colorado

USGS Publications Warehouse

Hoch, A.R.; Reddy, M.M.; Drever, J.I.

1999-01-01

Weathering of welded tuff near the summit of Snowshoe Mountain (3660 m) in southwestern Colorado was studied by analyzing infiltrating waters in the soil and associated solid phases. Infiltrating waters exhibit anomalously high potassium to silica ratios resulting from dissolution of a potassium-rich glass that occurs as a trace phase in the rock. In laboratory experiments using rock from the field site, initial dissolution generated potassium-rich solutions similar to those observed in the field. The anomalous potassium release decreased over time (about 1 month), after which the dominant cation was calcium, with a much lower potassium to silica ratio. The anomalous potassium concentrations observed in the infiltrating soil solutions result from weathering of freshly exposed rock surfaces. Continual mechanical disaggregation of the rock due to segregation freezing exposes fresh glass to weathering and thus maintains the source of potassium for the infiltrating water. The ongoing process of creation of fresh surfaces by physical processes is an important influence on the composition of infiltrating waters in the vadose zone.

Aquifer recharge with reclaimed water in the Llobregat Delta. Laboratory batch experiments and field test site.

NASA Astrophysics Data System (ADS)

Tobella, J.

2010-05-01

Summary Spain, as most other Mediterranean countries, faces near future water shortages, generalized pollution and loss of water dependent ecosystems. Aquifer recharge represents a promising option to become a source for indirect potable reuse purposes but presence of pathogens as well as organic and inorganic pollutants should be avoided. To this end, understanding the processes of biogeochemical degradation occurring within the aquifer during infiltration is capital. A set of laboratory batch experiments has been assembled in order to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. Data collected during laboratory experiments and monitoring activities at the Sant Vicenç dels Horts test site will be used to build and calibrate a numerical model (i) of the physical-chemical-biochemical processes occurring in the batches and (ii) of multicomponent reactive transport in the unsaturated/saturated zone at the test site. Keywords Aquifer recharge, batch experiments, emerging micropollutants, infiltration, numerical model, reclaimed water, redox conditions, Soil Aquifer Treatment (SAT). 1. Introduction In Spain, the Llobregat River and aquifers, which supply water to Barcelona, have been overexploited for years and therefore, suffer from serious damages: the river dries up on summer, riparian vegetation has disappeared and seawater has intruded the aquifer. In a global context, solutions to water stress problems are urgently needed yet must be sustainable, economical and safe. Recent developments of analytical techniques detect the presence of the so-called "emerging" organic micropollutants in water and soils. Such compounds may affect living organisms when occurring in the environment at very low concentrations (microg/l or ng/l). In wastewater and drinking water treatment plants, a remarkable removal of these chemicals from water can be obtained only using advanced and costly treatments. Nevertheless, a number of studies are demonstrating that physical, chemical and biochemical processes associated with water movement within the subsoil represent a natural alternative way to reduce the presence of these contaminants. This processes are called Soil Aquifer Treatment (SAT). Aquifer recharge will become a source for indirect potable reuse purposes as long as the presence of pathogens and organic and inorganic pollutants is avoided. To this end, understanding the biogeochemical degradation processes occurring within the aquifer during infiltration is capital. 2. Laboratory batch experiments A set of laboratory batch experiments has been assembled to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. The setup of the experiments consists of glass bottles containing 120 g of soil and 240 ml of synthetic water spiked with the mix of micropollutants. A source of easily degradable organic carbon and, depending on the type of test, electron acceptors are added in order to yield aerobic respiration and nitrate/iron/manganese/sulphate reduction conditions. The evolution of the processes is monitored by sacrificing duplicate bottles according to a defined schedule and analysing water for major and minor components as well as for micropollutants. Results from biotic tests are compared with abiotic ones in order to discern biodegradation from other chemical processes. The soil, the synthetic water and the micropollutants selected for the experiments are representative of a test site in the nearby of Barcelona (Spain) where artificial recharge of groundwater through ponds is going to be performed using river water or tertiary effluent from a waste water treatment plant. The results of the experiments improve the knowledge on the behaviour of the selected micropollutants under different redox conditions and provide with useful information on the conditions to develop at the test site during artificial recharge. The data collected during the laboratory experiments and in the test site will be used to build and calibrate a numerical model of the physical-chemical-biochemical processes developing in the batches and of multicomponent reactive transport in the unsaturated/saturated zone in the test site area. 3. Field test site The infiltration site of Sant Vicenç dels Horts has been selected to assessing the biogeochemical processes occurring during SAT. The system consists of two ponds that have been built as compensatory measure for the reduction in natural recharge caused by the construction of the High Speed Train Line. The first pond acts as a decantation pond while the second one acts as an infiltration basin (Figure 1). Recharge water comes from the tertiary treatment plant of the El Prat de Llobregat WWTP and the river (?). The CUADLL (Lower Llobregat Aquifer End-Users Community) is now managing the system operation. Tasks that are currently being carried out at this Test Site aims at (i) improving the local experience on MAR through infiltration ponds operational aspects and (ii) monitoring the changes in water quality during the recharge processes (unsaturated and saturated zone). Special attention is being paid to the fate of emerging organic pollutants (pharmaceuticals, surfactants, pesticides, etc.). The yielding of the monitoring will be compared with the results from the laboratory batch experiments on the behaviour of selected emerging organic pollutants. To this end, observation wells have been constructed, pressure / temperature / electrical conductivity transducers have been installed and the vadose zone under the infiltration pond has been instrumented (tensiometers, water content probes and suction cups). In addition double ring and infiltration tests have been performed in order to forecast the infiltration capacity of the basin.

Observation of flow processes in the vadose zone using ERT on different space and time scales: results, obstacles, and suggestions

NASA Astrophysics Data System (ADS)

Noell, Ursula; Ganz, Christina; Lamparter, Axel; Duijnisveld, Wilhelmus; Bachmann, Jörg

2013-04-01

Electrical resistivity tomography (ERT) observes the flow processes in the vadose zone indirectly. ERT has been used to estimate water flow in different soil types and under different flow conditions using active experiments or monitoring the natural process in many cases. Our experiments in sand and loess soil connected ERT with local soil probing using TDR devices and tensiometers in order to proof the reliability of the ERT inversion results in terms of infiltration velocity. Additionally, a colour tracer was used and sections through the infiltration zones were excavated in order to compare the shape of the dye -stained infiltration zone with the results of the ERT inversion. The data revealed the complicated infiltration pattern with a higher transport velocity in sand and a different shape than expected by classical soil hydraulic models. These results indicate the need for independent observations in order to correctly assess the water storage in the vadose zone with its hydrological consequences, the groundwater recharge and the contamination risk caused by rapid movement of water. ERT can be used for this purpose on different spatial- and time scales but for reliable results various obstacles need to be dealt with. Firstly, the ambiguity of the resistivity because soil resistivity depends on both, soil water content and electrical soil/water conductivity. This obstacle is less severe when the infiltration velocity is investigated, because then only the first onset of resistivity change is interpreted as the water arrival time. Our results show that the arrival of the water front as well as the final infiltration depth can be reliably detected. In contrast, this obstacle is very severe when the amount of water stored is observed using conductive tracer. The problem is not critical during a passive experiment when the natural rain fall and the waters fate through the vadose zone is monitored. The second obstacle is the limited resolution of ERT which deteriorates with depth. The resolution depends on the electrode distances and the depth resolution can be increased by using borehole electrodes. However, if one ha of land is to be observed with a reasonable number of electrodes (some 100) the resolution will be some 10 m. The structures, however, that influence the infiltration process, might be much smaller. Therefore, it is suggested to use ERT as the tool to observe and quantify the infiltration process with regard to time and space on a scale of some meters. For independent proof local TDR devices should be inserted within the investigated area for calibration. These results should then be used to establish a physical soil model that grasps the observed process correctly in time and space. The next step would then be to repeat these local measurements at different locations where the similarity of the processes is at doubt. Only when this is confirmed or discarded, further upscaling steps can be done reliably.

Identifying dominant controls on the water balance of partly sealed surfaces

NASA Astrophysics Data System (ADS)

Schuetz, Tobias; Schübl, Marleen; Siebert, Caroline; Weiler, Markus

2017-04-01

It is the challenge of modern urban development to obtain a near natural state for the urban water balance. For this purpose permeable alternatives to conventional surface sealing have been established during the last decades. A wealth of studies - under laboratory as well as field conditions - has emerged around the globe to examine the hydrological characteristics of different types of pavements. The main results of these studies - measured infiltration and evaporation rates, vary to a great extent between single studies and pavement types due to methodological approaches and local conditions. Within this study we analyze the controls of water balance components of partly sealed urban surfaces derived from an extensive literature review and a series of infiltration experiments conducted on historical and modern pavements within the city of Freiburg, Germany. Measured values published in 48 studies as well as the results of 30 double-ring infiltration experiments were compiled and sorted according to the measured parameter, the pavement type, pavement condition, age of the pavement, porosity of the pavement material and joint filling material as well as joint proportion of joint pavements. The main influencing factors on infiltration / hydraulic conductivity, evaporation rates and groundwater recharge of permeable pavements were identified and quantified using multiple linear regression methods. The analysis showed for both the literature study and our own infiltration experiments that condition and age of the pavement have the major influence on the pavement's infiltration capacity and that maintenance plays an important role for the long-term effectiveness of permeable pavements. For pavements with joints, the porosity of the pavement material seemed to have a stronger influence on infiltration capacity than the proportion of joint surface for which a clear influence could not be observed. Evaporation rates were compared for different surface categories as not enough measured values for different pavement types have been published. The highest evaporation can be expected for joint filling aggregates such as gravel and sand followed by bare soil (as reference), porous pavements and lastly non-porous pavements. The proportion of precipitation lost due to evaporation/evapotranspiration processes was expectedly highest on turf grid pavements, while maximum groundwater recharge rates were identified under non-porous pavements. Our results improve the tools available for urban water management controlling the state of urban water balances from a dominant surface runoff component to either dominant evaporation or groundwater components.

[Infiltration characteristics of soil water on loess slope land under intermittent and repetitive rainfall conditions].

PubMed

Li, Yi; Shao, Ming-An

2008-07-01

Based on the experiments of controlled intermittent and repetitive rainfall on slope land, the infiltration and distribution characteristics of soil water on loess slope land were studied. The results showed that under the condition of intermittent rainfall, the cumulative runoff during two rainfall events increased linearly with time, and the wetting front also increased with time. In the interval of the two rainfall events, the wetting front increased slowly, and the infiltration rate was smaller on steeper slope than on flat surface. During the second rainfall event, there was an obvious decreasing trend of infiltration rate with time. The cumulative infiltration on 15 degrees slope land was larger than that of 25 degrees slope land, being 178 mm and 88 mm, respectively. Under the condition of repetitive rainfall, the initial infiltration rate during each rainfall event was relatively large, and during the first rainfall, both the infiltration rate and the cumulative infiltration at various stages were larger than those during the other three rainfall events. However, after the first rainfall, there were no obvious differences in the infiltration rate among the next three rainfall events. The more the rainfall event, the deeper the wetting front advanced.

Focused Flow During Infiltration Into Ethanol-Contaminated Unsaturated Porous Media

NASA Astrophysics Data System (ADS)

Jazwiec, A.; Smith, J. E.

2017-12-01

The increasing commercial and industrial use of ethanol, e.g. in biofuels, has generated increased incidents of vadose zone contamination by way of ethanol spills and releases. This has increased the interest in better understanding behaviors of ethanol in unsaturated porous media and it's multiphase interactions in the vadose zone. This study uses highly controlled laboratory experiments in a 2-D (0.6mx0.6mx0.01m) flow cell to investigate water infiltration behaviors into ethanol-contaminated porous media. Ethanol and water were applied by either constant head or constant flux methods onto the surface of sands homogenously packed into the flow cell. The constant flux experiments at both low and high application rates were conducted using a rainulator with a row of hypodermic needles connected to a peristaltic pump. The constant head experiments were conducted using an 8cm diameter tension disk infiltrometer set to both low and high tensions. The presence of ethanol contamination generated solute-dependent capillarity induced focused flow (SCIFF) of water infiltration, which was primarily due to decreases in interfacial tensions at the air-liquid interfaces in the unsaturated sands as a function of ethanol concentration. SCIFF was clearly expressed as an unsaturated water flow phenomenon comprised of narrowly focused vertical flow fingers of water within the initially ethanol contaminated porous media. Using analyses of photos and video, comparisons were made between constant flux and constant head application methods. Further comparisons were made between low and high infiltration rates and the two sand textures used. A high degree of sensitivity to minor heterogeneity in relatively homogeneous sands was also observed. The results of this research have implications for rainfall infiltration into ethanol contaminated vadose zones expressing SCIFF, including implications for associated mass fluxes and the nature of flushing of ethanol from the unsaturated zone to groundwaters.

Infiltration into cropped soils: effect of rain and sodium adsorption ratio-impacted irrigation water.

PubMed

Suarez, Donald L; Wood, James D; Lesch, Scott M

2008-01-01

The sodium adsorption ratio (SAR) and salinity criteria for water suitability for irrigation have been developed for conditions where irrigation water is the only water source. It is not clear that these criteria are applicable to environments where there is a combination of rain and irrigation during the growing season. The interaction of rainfall with irrigation water is expected to result in increased sodicity hazard because of the low electrical conductivity of rain. In this study we examined the effects of irrigation waters of SAR 2, 4, 6, 8, and 10 mmol(1/2) L(-1/2) and electrical conductivities of 1 and 2 dS m(-1) on the infiltration rate of two soils with alternating cycles of rain (simulated with a rainfall sprinkler) and irrigation water, separated by drying cycles. The infiltration rate of surface samples from two soils, Kobase silty clay (fine, smectitic, frigid, Torrertic Haplustept) and Glendive very fine sandy loam (coarse-loamy, mixed superactive, calcareous, frigid Aridic Ustifluvent) were evaluated under alfalfa (Medicago sativa) cropped conditions for over 140 d and under full canopy cover. Reductions in infiltration were observed for both soils for SAR above 2, and the reductions became more severe with increasing SAR. Saturated hydraulic conductivity measurements taken from undisturbed cores at the end of the experiment were highly variable, suggesting that in situ infiltration measurements may be preferred when evaluating SAR effects.

Atrazine distribution measured in soil and leachate following infiltration conditions.

PubMed

Neurath, Susan K; Sadeghi, Ali M; Shirmohammadi, Adel; Isensee, Allan R; Torrents, Alba

2004-01-01

Atrazine transport through packed 10 cm soil columns representative of the 0-10 cm soil horizon was observed by measuring the atrazine recovery in the total leachate volume, and upper and lower soil layers following infiltration of 7.5 cm water using a mechanical vacuum extractor (MVE). Measured recoveries were analyzed to understand the influence of infiltration rate and delay time on atrazine transport and distribution in the column. Four time periods (0.28, 0.8, 1.8, and 5.5 h) representing very high to moderate infiltration rates (26.8, 9.4, 4.2, and 1.4 cm/h) were used. Replicate soil columns were tested immediately and following a 2-d delay after atrazine application. Results indicate atrazine recovery in leachate was independent of infiltration rate, but significantly lower for infiltration following a 2-d delay. Atrazine distribution in the 0-1 and 9-10 cm soil layers was affected by both infiltration rate and delay. These results are in contrast with previous field and laboratory studies that suggest that atrazine recovery in the leachate increases with increasing infiltration rate. It appears that the difference in atrazine recovery measured using the MVE and other leaching experiments using intact soil cores from this field site and the rain simulation equipment probably illustrates the effect of infiltrating water interacting with the atrazine present on the soil surface. This work suggests that atrazine mobilization from the soil surface is also dependent on interactions of the infiltrating water with the soil surface, in addition to the rate of infiltration through the surface soil.

Quantification of dynamic soil-vegetation feedbacks following an isotopically labelled precipitation pulse

NASA Astrophysics Data System (ADS)

Piayda, Arndt; Dubbert, Maren; Siegwolf, Rolf; Cuntz, Matthias; Werner, Christiane

2017-05-01

The presence of vegetation alters hydrological cycles of ecosystems. Complex plant-soil interactions govern the fate of precipitation input and water transitions through ecosystem compartments. Disentangling these interactions is a major challenge in the field of ecohydrology and a pivotal foundation for understanding the carbon cycle of semi-arid ecosystems. Stable water isotopes can be used in this context as tracer to quantify water movement through soil-vegetation-atmosphere interfaces. The aim of this study is to disentangle vegetation effects on soil water infiltration and distribution as well as dynamics of soil evaporation and grassland water use in a Mediterranean cork oak woodland during dry conditions. An irrigation experiment using δ18O labelled water was carried out in order to quantify distinct effects of tree and herbaceous vegetation on the infiltration and distribution of event water in the soil profile. Dynamic responses of soil and herbaceous vegetation fluxes to precipitation regarding event water use, water uptake depth plasticity, and contribution to ecosystem soil evaporation and transpiration were quantified. Total water loss to the atmosphere from bare soil was as high as from vegetated soil, utilizing large amounts of unproductive evaporation for transpiration, but infiltration rates decreased. No adjustments of main root water uptake depth to changes in water availability could be observed during the experiment. This forces understorey plants to compete with adjacent trees for water in deeper soil layers at the onset of summer. Thus, understorey plants are subjected to chronic water deficits faster, leading to premature senescence at the onset of drought. Despite this water competition, the presence of cork oak trees fosters infiltration and reduces evapotranspirative water losses from the understorey and the soil, both due to altered microclimatic conditions under crown shading. This study highlights complex soil-plant-atmosphere and inter-species interactions controlling rain pulse transitions through a typical Mediterranean savannah ecosystem, disentangled by the use of stable water isotopes.

Effect of integrating straw into agricultural soils on soil infiltration and evaporation.

PubMed

Cao, Jiansheng; Liu, Changming; Zhang, Wanjun; Guo, Yunlong

2012-01-01

Soil water movement is a critical consideration for crop yield in straw-integrated fields. This study used an indoor soil column experiment to determine soil infiltration and evaporation characteristics in three forms of direct straw-integrated soils (straw mulching, straw mixing and straw inter-layering). Straw mulching is covering the land surface with straw. Straw mixing is mixing straw with the top 10 cm surface soil. Then straw inter-layering is placing straw at the 20 cm soil depth. There are generally good correlations among the mulch integration methods at p < 0.05, and with average errors/biases <10%. Straw mixing exhibited the best effect in terms of soil infiltration, followed by straw mulching. Due to over-burden weight-compaction effect, straw inter-layering somehow retarded soil infiltration. In terms of soil water evaporation, straw mulching exhibited the best effect. This was followed by straw mixing and then straw inter-layering. Straw inter-layering could have a long-lasting positive effect on soil evaporation as it limited the evaporative consumption of deep soil water. The responses of the direct straw integration modes to soil infiltration and evaporation could lay the basis for developing efficient water-conservation strategies. This is especially useful for water-scarce agricultural regions such as the arid/semi-arid regions of China.

Managed aquifer recharge: the fate of pharmaceuticals from infiltrated treated wastewater investigated through soil column experiments

NASA Astrophysics Data System (ADS)

Silver, Matthew; Selke, Stephanie; Balsaa, Peter; Wefer-Roehl, Annette; Kübeck, Christine; Schüth, Christoph

2017-04-01

The EU FP7 project MARSOL addresses water scarcity challenges in arid regions, where managed aquifer recharge (MAR) is an upcoming technology to recharge depleted aquifers using alternative water sources. Within this framework, column experiments were conducted to investigate the fate of pharmaceuticals when secondary treated wastewater (TWW) is infiltrated through a natural soil (organic matter content 6.8%) being considered for MAR. Three parallel experiments were run under conditions of continuous infiltration (one column) and wetting-drying cycles (two columns, with different analytes) over a 16 month time period. The pharmaceuticals diclofenac, ibuprofen, carbamazepine, naproxen, gemfibrozil, and fenoprofen, as well as the antibiotics doxycycline, sulfadimidine, and sulfamethoxazole, are commonly present in treated wastewater in varying concentrations. For the experiments, concentration variability was reduced by spiking the column inflow water with these compounds. Concentrations were periodically analyzed at different depths in each column and the mass passing each depth over the duration of the experiment was calculated. At the end of the experiments, sorbed pharmaceuticals were extracted from soil samples collected from different depths. A pressurized liquid extraction method was developed and resulted in recoveries from spiked post-experiment soil samples ranging from 64% (gemfibrozil) to 82% (carbamazepine) for the six non-antibiotic compounds. Scaling results by these recovery rates, the total mass of pharmaceuticals sorbed to the soil in the columns was calculated and compared to the calculated attenuated mass (i.e. mass that left the water phase). The difference between the attenuated mass and the sorbed mass is considered to be mass that degraded. Results for continuous infiltration conditions indicate that for carbamazepine and diclofenac, sorption is the primary attenuation mechanism, with missing (i.e. degraded) mass lying within the propagated measurement error range. Over the duration of the experiment, 36% of carbamazepine and 59% of diclofenac passed the deeper sediment (depth 71 cm, last sampling point along an 88 cm flowpath through soil) in the water phase. On the other hand, the compounds fenoprofen, gemfibrozil, ibuprofen and naproxen showed degradation rates (degraded relative to total infiltrated mass) of 51%, 57%, 63% and 95%, respectively. Corresponding results for wetting-drying cycles (one column with antibiotics spiked and analyzed, one without) will also be presented, where oxygenated conditions during drying periods and may influence degradation. The results indicate that while substantial portions of mass degrade for some compounds, sorption is also an important mechanism for mass leaving the water phase. Although the most sorbed mass is present near the surface, substantial amounts of mass also sorb at depth. A flowpath through a thick unsaturated zone composed of a soil favorable to sorbing polar organic compounds presents the best chance to attenuate the most mass, but consequently micropollutants will accumulate in the soil if degradation remains low and re-mobilization of the compounds may occur when system conditions change. However, the results of these experiments also suggest that for the chosen soil and infiltration conditions, near-complete degradation of fenoprofen, gemfibrozil, ibuprofen and naproxen is possible considering a substantial unsaturated zone thickness.

Project Work Plan: Sequestration of Strontium-90 Subsurface Contamination in the Hanford 100-N Area by Surface Infiltration of an Apatite Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szecsody, Jim E.

2006-04-30

We propose to develop an infiltration strategy that defines the precipitation rate of an apatite-forming solution and Sr-90 sequestration processes under variably saturated (low water content) conditions. We will develop this understanding through small-scale column studies, intermediate-scale two-dimensional (2-D) experiments, and numerical modeling to quantify individual and coupled processes associated with apatite formation and Sr-90 transport during and after infiltration of the Ca-citrate-PO4 solution. Development of capabilities to simulate these coupled biogeochemical processes during both injection and infiltration will be used to determine the most cost-effective means to emplace an in situ apatite barrier with a longevity of 300 yearsmore » to permanently sequester Sr-90 until it decays. Biogeochemical processes that will be investigated are citrate biodegradation and apatite precipitation rates at varying water contents as a function of water content. Coupled processes that will be investigated include the influence of apatite precipitation (which occupies pore space) on the hydraulic and transport properties of the porous media during infiltration.« less

Passive Microwave Observation of Soil Water Infiltration

NASA Technical Reports Server (NTRS)

Jackson, Thomas J.; Schmugge, Thomas J.; Rawls, Walter J.; ONeill, Peggy E.; Parlange, Marc B.

1997-01-01

Infiltration is a time varying process of water entry into soil. Experiments were conducted here using truck based microwave radiometers to observe small plots during and following sprinkler irrigation. Experiments were conducted on a sandy loam soil in 1994 and a silt loam in 1995. Sandy loam soils typically have higher infiltration capabilities than clays. For the sandy loam the observed brightness temperature (TB) quickly reached a nominally constant value during irrigation. When the irrigation was stopped the TB began to increase as drainage took place. The irrigation rates in 1995 with the silt loam soil exceeded the saturated conductivity of the soil. During irrigation the TB values exhibited a pattern that suggests the occurrence of coherent reflection, a rarely observed phenomena under natural conditions. These results suggested the existence of a sharp dielectric boundary (wet over dry soil) that was increasing in depth with time.

Effect of infiltrated water on rheology of plagioclase feldspar under lower crustal condition

NASA Astrophysics Data System (ADS)

Kido, M.; Muto, J.; Koizumi, S.; Nagahama, H.

2016-12-01

Fluids in the deep crust have an important role in deformation of lithosphere and seismicity. In this study, we performed deformation experiments to reveal rheological properties of plagioclase feldspars as a main constituent of crustal materials with infilitrated water. Axial compression tests on synthetic polycrystalline anorthite (An) were performed in a Griggs-type deformation apparatus at temparature of 900 °C, strain rates of roughly about 10-5 s-1 and various confining pressures of 0.8-1.4 GPa. Distilled water was added on samples before tests. Times for infiltration of water into samples were changed to investigate the variation of strength associated with diffusion of water. Strengths of wet An tended to decrease with infiltration time or strain magnitude. If other conditions such as temperature, time and strain being the same, strengths increase with confining pressures. Recovered samples show that deformation was concentrated in the lower part of samples. Differential stresses were significantly lower than predicted values by a previous flow law for wet An obtained by low pressure gas apparatus ( 0.4 GPa, Rybacki et al., 2006). This implies that the effect of water on mechanical behavior in higher pressure might be larger than those predicted by lower pressure experiments. Ideal water concentration and strength profile of internal of samples were estimated by one-dimensional model of grain boundary diffusion. Estimated strength of internal part of samples was significant higher than measured stresses. There is possibility that cataclastic flow partially occurred in samples. In addition, deformation-enhanced fluid flow probably occurred. In conclusion, strength of wet An depends on water infiltration time, strain magnitude and confining pressure. The results suggest that the strength of fluid-rich regions in the lower crust becomes lower than that predicted by previous studies.

Efficient infiltration of water in the subsurface by using point-wells: A field study

NASA Astrophysics Data System (ADS)

Lopik, J. V.; Schotting, R.; Raoof, A.

2017-12-01

The ability to infiltrate large volumes of water in the subsurface would have great value for battling flooding in urban regions. Moreover, efficient water infiltration is key to optimize underground aquifer storage and recovery (ASR), aquifer thermal energy storage (ATES), as well as construction dewatering systems. Usually, variable infiltration rates of large water quantities could have a huge hydrogeological impact in the upper part of (phreatic) aquifer systems. In urban regions, minimizing excessive groundwater table fluctuations are necessary. A newly developed method, Fast, High Volume Infiltration (FHVI), by Dutch dewatering companies can be used to enable fast injection into the shallow subsurface. Conventional infiltration methods are using injection wells that screen large parts of the aquifer depth, whereas FHVI uses a specific infiltration point (1-m well screen) in the aquifer. These infiltration points are generally thin, high permeable layers in the aquifer of approximately 0.5-2 meter thick, and are embedded by less permeable layers. Currently, much higher infiltration pressures in shallow aquifers can be achieved with FHVI (up to 1 bar) compared to conventional infiltration methods ( 0.2 bar). Despite the high infiltration pressures and high discharge rate near the FHVI-filter, the stresses on shallow groundwater levels are significantly reduced with FHVI. In order to investigate the mechanisms that enable FHVI, a field experiment is conducted in a sandy aquifer to obtain insight in the 3-D hydraulic pressure distribution and flow patterns around a FHVI-filter during infiltration. A detailed characterization of the soil profile is obtained by using soil samples and cone pressure tests with a specific hydraulic profiling tool to track the vertical variation in aquifer permeability. A tracer test with bromide and heat is conducted to investigate preferential flow paths. The experimental data show that tracking small heterogeneities in aquifers and analysing the permeability difference ratio between the aimed infiltration layer and the surrounding layers in the aquifer are key to optimize the configuration of the FHVI-well. The results show that the use of point wells in thin, high permeable layers could drastically improve the efficiency of the infiltration system.

Infiltration and soil erosion modelling on Lausatian post mine sites

NASA Astrophysics Data System (ADS)

Kunth, Franziska; Schmidt, Jürgen

2013-04-01

Land management of reclaimed lignite mine sites requires long-term and safe structuring of recultivation areas. Erosion by water leads to explicit soil losses, especially on heavily endangered water repellent and non-vegetated soil surfaces. Beyond that, weathering of pyrite-containing lignite burden dumps causes sulfuric acid-formation, and hence the acidification of groundwater, seepage water and surface waters. Pyrite containing sediment is detached by precipitation and transported into worked-out open cuts by draining runoff. In addition to ground water influence, erosion processes are therefore involved in acidification of surface waters. A model-based approach for the conservation of man-made slopes of post mining sites is the objective of this ongoing study. The study shall be completed by modeling of the effectiveness of different mine site recultivation scenarios. Erosion risks on man-made slopes in recultivation areas should be determined by applying the physical, raster- and event based computer model EROSION 2D/3D (Schmidt, 1991, 1992; v. Werner, 1995). The widely used erosion model is able to predict runoff as well as detachment, transport and deposition of sediments. Lignite burden dumps contain hydrophobic substances that cover soil particles. Consequently, these soils show strong water repellency, which influences the processes of infiltration and soil erosion on non-vegetated, coal containing dump soils. The influence of water repellency had to be implemented into EROSION 2D/3D. Required input data for soil erosion modelling (e.g. physical soil parameters, infiltration rates, calibration factors, etc.) were gained by soil sampling and rainfall experiments on non-vegetated as well as recultivated reclaimed mine sites in the Lusatia lignite mining region (southeast of Berlin, Germany). The measured infiltration rates on the non-vegetated water repellent sites were extremely low. Therefore, a newly developed water repellency-factor was applied to depict infiltration and erosion processes on water repellent dump soils. For infiltration modelling with EROSION 2D calibration factors (e.g. water repellency factor, skin-factor, etc.) were determined in different steps by calibrating computer modelled infiltration, respectively volume rate of flow to the measured data.

Nutrient transport and transformation beneath an infiltration basin

USGS Publications Warehouse

Sumner, D.M.; Rolston, D.E.; Bradner, L.A.

1998-01-01

Field experiments were conducted to examine nutrient transport and transformation beneath an infiltration basin used for the disposal of treated wastewater. Removal of nitrogen from infiltrating water by denitrification was negligible beneath the basin, probably because of subsurface aeration as a result of daily interruptions in basin loading. Retention of organic nitrogen in the upper 4.6 m of the unsaturated zone (water table depth of approximately 11 m) during basin loading resulted in concentrations of nitrate as much as 10 times that of the applied treated wastewater, following basin 'rest' periods of several weeks, which allowed time for mineralization and nitrification. Approximately 90% of the phosphorus in treated wastewater was removed within the upper 4.6 m of the subsurface, primarily by adsorption reactions, with abundant iron and aluminum oxyhydroxides occurring as soil coatings. A reduction in the flow rate of infiltrating water arriving at the water table may explain the accumulation of relatively coarse (>0.45 ??m), organic forms of nitrogen and phosphorus slightly below the water table. Mineralization and nitrification reactions at this second location of organic nitrogen accumulation contributed to concentrations of nitrate as much as three times that of the applied treated wastewater. Phosphorus, which accumulated below the water table, was immobilized by adsorption or precipitation reactions during basin rest periods.Field experiments were conducted to examine nutrient transport and transformation beneath an infiltration basin used for the disposal of treated wastewater. Removal of nitrogen from infiltrating water by denitrification was negligible beneath the basin, probably because of subsurface aeration as a result of daily interruptions in basin loading. Retention of organic nitrogen in the upper 4.6 m of the unsaturated zone (water table depth of approximately 11 m) during basin loading resulted in concentrations of nitrate as much as 10 times that of the applied treated wastewater, following basin 'rest' periods of several weeks, which allowed time for mineralization and nitrification. Approximately 90% of the phosphorus in treated wastewater was removed within the upper 4.6 m of the subsurface, primarily by adsorption reactions, with abundant iron and aluminum oxyhydroxides occurring as soil coatings. A reduction in the flow rate of infiltrating water arriving at the water table may explain the accumulation of relatively coarse (>0.45 ??m), organic forms of nitrogen and phosphorus slightly below the water table. Mineralization and nitrification reactions at this second location of organic nitrogen accumulation contributed to concentrations of nitrate as much as three times that of the applied treated wastewater. Phosphorus, which accumulated below the water table, was immobilized by adsorption or precipitation reactions during basin rest periods.

Importance of rodents for hydrology: lessons learnt from various field experiments

NASA Astrophysics Data System (ADS)

van Schaik, Loes; Zangerlé, Anne; Schneider, Anne-Kathrin; Schröder, Boris; Eccard, Jana

2017-04-01

organisms are known to create soil macropores of different sizes and with varying extent and orientation: most commonly earthworms, rodents, moles and roots. Preferential flow through macropore networks is dynamic and typically occurs when short individual macropores become connected at the hillslope scale as the nodes between the macropores become wet. Large lateral macropores may contribute to rapid subsurface stormflow of water and solutes at hillslope scale and supply a significant part of the catchment scale discharge during high intensity rainfall events even under relatively dry catchment state. Outflow from soil pipes, especially in the valley bottom or along the banking near to streams, is frequently observed, however, it remains a challenge to measure the spatial distribution, extent and connectivity of macropores at hill slope scales. We hypothesize that local information on organism abundances may be used as an indicator for spatial variability in infiltration, water storage and fluxes at the small scale and that knowledge on the landscape scale spatial distribution of organisms can provide information on connectivity of macropores at hillslope scale. Here we summarize the lessons learnt during three years of measurements aimed at determining the influence of rodent burrows on soil hydrology in a meso-scale catchment. Within the Attert Catchment (297 km2) in Luxembourg we performed sprinkling experiments with a brilliant blue tracer on twelve plots, of which six directly above rodent burrow openings and six on a surface without a rodent burrow opening, in order to examine the influence of the burrow openings on the infiltration pattern. Then we tested the extent of flow through mice burrows in different forest types, with varying geology and slope, by supplying 5 Liters of water with brilliant blue tracer directly to 24 burrow openings at soil surface. We excavated the burrows to measure how far the water was transported laterally in the burrow. Though we have serendipitous evidence of lateral water flow through large macropores in deeper soil layers from other projects, with the experiments we performed with the purpose to characterize this, the water did not seem to infiltrate into the burrow openings at the soil surface at all and the infiltration pattern under burrows was not different from that in soils without these openings. The five liter of brilliant blue dyed water which we poured into burrow openings did not flow far into the burrows, it generally infiltrated straight away into the surrounding soil. These results seem to show that the infiltration of water to rodent macropores during high intensity events does not take place at the soil surface but rather through other macropores, e.g. earthworm channels, which connect to deeper lateral channels. Also the lateral flow of water through the rodent burrows is apparently more effective in the deeper soils, where we occasionally saw a burrow with completely blue walls but little infiltration into the surrounding matrix.

Preferential flow in the vadose zone and interface dynamics: Impact of microbial exudates

NASA Astrophysics Data System (ADS)

Li, Biting; Pales, Ashley R.; Clifford, Heather M.; Kupis, Shyla; Hennessy, Sarah; Liang, Wei-Zhen; Moysey, Stephen; Powell, Brian; Finneran, Kevin T.; Darnault, Christophe J. G.

2018-03-01

In the hydrological cycle, the infiltration process is a critical component in the distribution of water into the soil and in the groundwater system. The nonlinear dynamics of the soil infiltration process yield preferential flow which affects the water distribution in soil. Preferential flow is influenced by the interactions between water, soil, plants, and microorganisms. Although the relationship among the plant roots, their rhizodeposits and water transport in soil has been the subject of extensive study, the effect of microbial exudates has been studied in only a few cases. Here the authors investigated the influence of two artificial microbial exudates-catechol and riboflavin-on the infiltration process, particularly unstable fingered flow, one form of preferential flow. Flow experiments investigating the effects of types and concentrations of microbial exudates on unstable fingered flow were conducted in a two-dimensional tank that was filled with ASTM

Hillslope run-off thresholds with shrink–swell clay soils

USGS Publications Warehouse

Stewart, Ryan D.; Abou Najm, Majdi R.; Rupp, David E.; Lane, John W.; Uribe, Hamil C.; Arumí, José Luis; Selker, John S.

2015-01-01

Irrigation experiments on 12 instrumented field plots were used to assess the impact of dynamic soil crack networks on infiltration and run-off. During applications of intensity similar to a heavy rainstorm, water was seen being preferentially delivered within the soil profile. However, run-off was not observed until soil water content of the profile reached field capacity, and the apertures of surface-connected cracks had closed >60%. Electrical resistivity measurements suggested that subsurface cracks persisted and enhanced lateral transport, even in wet conditions. Likewise, single-ring infiltration measurements taken before and after irrigation indicated that infiltration remained an important component of the water budget at high soil water content values, despite apparent surface sealing. Overall, although the wetting and sealing of the soil profile showed considerable complexity, an emergent property at the hillslope scale was observed: all of the plots demonstrated a strikingly similar threshold run-off response to the cumulative precipitation amount. 

In-situ arsenic removal during groundwater recharge through unsaturated alluvium

USGS Publications Warehouse

O'Leary, David; Izbicki, John; T.J. Kim,; Clark Ajawani,; Suarez, Donald; Barnes, Thomas; Thomas Kulp,; Burgess, Matthew K.; Tseng, Iwen

2015-01-01

OBJECTIVES The purpose of this study was to determine the feasibility and sustainability of in-situ removal of arsenic from water infiltrated through unsaturated alluvium. BACKGROUND Arsenic is naturally present in aquifers throughout the southwestern United States and elsewhere. In January 2006, the U.S. Environmental Protection Agency (EPA) lowered the Maximum Contaminant Level (MCL) for arsenic from 50 to 10 micrograms per liter (g/L). This raised concerns about naturally-occurring arsenic in groundwater. Although commercially available systems using sorbent iron or aluminum oxide resins are available to treat high-arsenic water, these systems are expensive to build and operate, and may generate hazardous waste. Iron and aluminum oxides occur naturally on the surfaces of mineral grains that compose alluvial aquifers. In areas where alluvial deposits are unsaturated, these oxides may sorb arsenic in the same manner as commercial resins, potentially providing an effective low-cost alternative to commercially engineered treatment systems. APPROACH The Antelope Valley within the Mojave Desert of southern California contains a shallow water-table aquifer with arsenic concentrations of 5 g/L, and a deeper aquifer with arsenic concentrations of 30 g/L. Water was pumped from the deep aquifer into a pond and infiltrated through an 80 m-thick unsaturated zone as part of field-scale and laboratory experiments to treat high-arsenic groundwater and recharge the shallow water table aquifer at the site. The field-scale recharge experiment included the following steps: 1) construction of a recharge pond 2) test drilling for sample collection and instrument installation adjacent to the pond 3) monitoring downward migration of water infiltrated from the pond 4) monitoring changes in selected trace-element concentrations as water infiltrated through the unsaturated zone Data from instruments within the borehole adjacent to the pond were supplemented with borehole and surface geophysical data to evaluate the lateral spreading of water as it moved downward through the unsaturated zone. Three laboratory studies were undertaken. Sequential extraction was used to evaluate the abundance of iron, aluminum, and manganese oxides and selected trace elements on operationally defined sites on the surfaces of mineral grains collected before and after infiltration from the pond. Secondly, radio-labeled arsenic-73 microcosm experiments evaluated the potential for incorporation of arsenic sorbed to exchange sites on mineral grains into less reactive crystalline mineral structures with time. Finally, column studies evaluated arsenic sorption and the pH dependence of sorption for selected unsaturated zone materials.RESULTS/CONCLUSIONS Between December 2010 and July 2012, more than 120,000 cubic meters (m3 ) (about 97 acre-feet) of high-arsenic groundwater was pumped from the deep aquifer into a 0.11 hectare (about 0.27 acres) pond and infiltrated though an 80-meter (about 260 feet) thick unsaturated zone to recharge a water-table aquifer. Arsenic concentrations were lowered from 30 to 2 g/L as water infiltrated though the unsaturated zone at the site. Some uranium, possibly associated with past agricultural land use at the site, was mobilized to concentrations as high as 66 g/L within the unsaturated zone during the experiment. Uranium was resorbed and the high uranium concentrations did not reach the water table at the site. Concentrations of other trace elements, including antimony, chromium, vanadium, and selenium were low throughout the study. Infiltration rates from the pond were as high as 0.4 meters per day (1.1 feet per day, ft/d), and the wetting front moved downward about 25 centimeters per day (cm/d) (0.8 ft/d) to a depth of about 50 m (about 165 feet). Clay layers at that depth slowed the downward movement of the wetting front to about 5 cm/d (0.16 ft/d). Lateral movement of the wetting front was monitored using sequential direct-current (DC) surface and sequential electromagnetic (EM) and DC borehole resistivity. Most lateral movement occurred on a clay layer about 50 m (about 165 feet) below land surface. Infiltrated water reached the water table in January 2013. At the water table, the “wetted footprint” of water infiltrated from the pond, indicated by surface resistivity data, was about 13 hectares (about 32 acres). On the basis of data collected at the site, there is enough sorbent material to operate this pond and treat groundwater having an arsenic concentration of 30 g/L to 2 g/L for about 500 years. Toxicity Characteristic Leaching Procedure (TCLP) data showed arsenic concentrations to be below hazardous levels beneath the pond after the experiment. Pond maintenance may be required to keep infiltration rates high, and prevent accumulation of organic material on the pond bottom, although organic material on the pond bottom may increase removal of other trace elements in infiltrated water including chromium, selenium, and vanadium. Laboratory results are consistent with the field data and show sorption of arsenic in 10 cm (0.3 feet) columns to about 2 g/L over a pH range of 6 to 8, and at influent arsenic concentrations as high as 300 g/L, without breakthrough in 50 pore volumes. Column results suggest that the insitu treatment may remove arsenic in a range of hydrogeologic settings, and would not necessarily be restricted to alkaline alluvial aquifers common throughout the southwestern United States. Radiolabeled arsenic-73 experiments show that although arsenic is initially weakly sorbed (and potentially mobile), with time arsenic is incorporated into amorphous materials. One year after sorption onto surface exchange sites, most sorbed arsenic is incorporated into crystalline oxide minerals on the surfaces of primary mineral grains and is less mobile. Results of the study suggest that long-term land use restrictions on sites used for in-situ treatment of arsenic may not be needed to control water applied to surface materials. This minimizes some regulatory concerns about future land use at sites used for in-situ arsenic treatment. However, future land uses that may alter reduction-oxidation conditions in the subsurface should be avoided, such as infiltration of stormwater recharge or recharge with other water having high organic carbon concentrations (including unsewered residential land use, dairy or other confined animal operations).

Novel instruments for in situ continuous Rn-222 measurement in groundwater and the application to river bank infiltration.

PubMed

Gilfedder, B S; Hofmann, H; Cartwright, I

2013-01-15

There is little known about the short-term dynamics of groundwater-surface water exchange in losing rivers. This is partly due to the paucity of chemical techniques that can autonomously collect high-frequency data in groundwater bores. Here we present two new instruments for continuous in situ (222)Rn measurement in bores for quantifying the surface water infiltration rate into an underlying or adjacent aquifer. These instruments are based on (222)Rn diffusion through silicone tube membranes, either wrapped around a pole (MonoRad) or strung between two hollow end pieces (OctoRad). They are combined with novel, robust, low-cost Geiger counter (222)Rn detectors which are ideal for long-term autonomous measurement. The down-hole instruments have a quantitative response time of about a day during low flow, but this decreases to <12 h during high-flow events. The setup was able to trace river water bank infiltration during moderate to high river flow during two field experiments. Mass-balance calculations using the (222)Rn data gave a maximum infiltration rate of 2 m d(-1). These instruments offer the first easily constructible system for continuous (222)Rn analysis in groundwater, and could be used to trace surface water infiltration in many environments including rivers, lakes, wetlands, and coastal settings.

Predicted Infiltration for Sodic/Saline Soils from Reclaimed Coastal Areas: Sensitivity to Model Parameters

PubMed Central

She, Dongli; Yu, Shuang'en; Shao, Guangcheng

2014-01-01

This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline) and 1960 (Soil B, nonsaline) were used, with bulk densities of 1.4 or 1.5 g/cm3. A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ 0 was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils. PMID:25197699

Predicted infiltration for sodic/saline soils from reclaimed coastal areas: sensitivity to model parameters.

PubMed

Liu, Dongdong; She, Dongli; Yu, Shuang'en; Shao, Guangcheng; Chen, Dan

2014-01-01

This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline) and 1960 (Soil B, nonsaline) were used, with bulk densities of 1.4 or 1.5 g/cm(3). A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ₀ was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils.

Two and three-dimensional quantitative neutron imaging of the water distribution during ponded infiltration

NASA Astrophysics Data System (ADS)

Sacha, Jan; Snehota, Michal; Jelinkova, Vladimira

2016-04-01

Information on spatial and temporal water and air distribution in a soil sample during hydrological processes is important for evaluating current and developing new water transport models. Modern imaging techniques such as neutron imaging (NI) allow relatively short acquisition times and high resolution of images. At the same time, the appropriate data processing has to be applied to obtain results free of bias and artifacts. In this study a ponded infiltration experiments were conducted on two soil samples packed into the quartz glass columns of inner diameter of 29 and 34 mm, respectively. First sample was prepared by packing of fine and coarse fractions of sand and the second sample was packed using coarse sand and disks of fine porous ceramic. Ponded infiltration experiments conducted on both samples were monitored by neutron radiography to produce two dimensional (2D) projection images during the transient phase of infiltration. During the steady state flow stage of experiments neutron tomography was utilized to obtain three-dimensional (3D) information on gradual water redistribution. The acquired radiographic images were normalized for background noise and spatial inhomogeneity of the detector, fluctuations of the neutron flux in time and for spatial inhomogeneity of the neutron beam. The radiograms of dry sample were subtracted from all subsequent radiograms to determine water thickness in the 2D projection images. All projections were corrected for beam hardening and neutron scattering by empirical method of Kang et al. (2013). Parameters of the correction method uses were identified by two different approaches. The first approach was based on fitting the NI derived water thickness representing the water filled region in the layer of water above the sample surface to actual water thickness. In the second approach the NI derived volume of water in the entire sample in given time was fitted to corresponding gravimetrically determined amount of water in the sample. Tomography images were reconstructed from the both corrected and uncorrected water thickness maps to obtain the 3D spatial distribution of water content within the sample. Without the correction the beam hardening and scattering effects overestimated the water content values close to the sample perimeter and underestimated the values close to the center of the sample, however the total water content of whole sample was the same in both cases.

Experimental characterization of 3-dimensional gravity-driven fingering in a porous medium

NASA Astrophysics Data System (ADS)

Dalbe, Marie-Julie; Juanes, Ruben

2017-11-01

When water infiltrates a dry porous media, a gravity-driven instability can be observed. Water will penetrate the porous media along preferential paths, called fingers. This gravity-driven unstable multiphase flow has important implications for natural phenomena such as rainwater infiltration in soil and secondary oil migration in reservoir rocks. While several experimental and numerical studies have described the instability in 2-dimensional (2D) settings, fundamental questions remain on the morphodynamics of gravity fingering in 3D. We developed a 3D experimental set-up based on planar laser-induced fluorescence of index-matched fluids that allows us to image this phenomenon dynamically. We study the impact of some crucial parameters such as rainfall rate or grain size on the finger size and velocity. In addition, experiments in stratified media reveal interesting dynamics of finger flow across material interfaces, an essential aspect towards the understanding of water infiltration in soils.

Simulating the evolution of non-point source pollutants in a shallow water environment.

PubMed

Yan, Min; Kahawita, Rene

2007-03-01

Non-point source pollution originating from surface applied chemicals in either liquid or solid form as part of agricultural activities, appears in the surface runoff caused by rainfall. The infiltration and transport of these pollutants has a significant impact on subsurface and riverine water quality. The present paper describes the development of a unified 2-D mathematical model incorporating individual models for infiltration, adsorption, solubility rate, advection and diffusion, which significantly improve the current practice on mathematical modeling of pollutant evolution in shallow water. The governing equations have been solved numerically using cubic spline integration. Experiments were conducted at the Hydrodynamics Laboratory of the Ecole Polytechnique de Montreal to validate the mathematical model. Good correspondence between the computed results and experimental data has been obtained. The model may be used to predict the ultimate fate of surface applied chemicals by evaluating the proportions that are dissolved, infiltrated into the subsurface or are washed off.

Why biochar application did not improve the soil water retention of a sandy soil: An investigation into the underlying mechanisms.

NASA Astrophysics Data System (ADS)

Jeffery, Simon; Meinders, Marcel B. J.; Stoof, Cathelijne; Bezemer, T. Martijn; vande Voorde, Tess F. J.; Mommer, Liesje; Willem van Groenigen, Jan

2015-04-01

Biochar application to soil is currently being widely touted as a means to improve soil quality and to enhance the provision of numerous ecosystem services, including water storage, in soils. However, evidence for hydrological effects in the primary literature remain inconclusive with contradictory effects reported. The mechanisms behind such contradictory results are not yet elucidated. As such we aimed to investigate the effects of biochar on soil water retention and infiltration, as well as the underlying mechanisms. To do so we set up two field experiments with biochar produced from herbaceous feedstock through slow pyrolysis at two temperatures (400°C and 600°C). In the first experiment both biochars were applied at a rate of 10 t ha-1 to separate plots in a sandy soil in a North European grassland. In a separate experiment, the biochar produced at 400°C was applied to a different set of plots in the same grassland at rates equivalent to 1, 5, 20 and 50 t ha-1. Soils from these experiments were analysed for soil water retention and infiltration rate as well as aggregate stability and other soil physical parameters. The pore structure of the biochar was fully characterised using X-ray computed micro-tomography (XRT) and hydrophobicity determined using contact angle measurements. There were no significant effects of biochar application on soil water retention, field saturated conductivity or aggregate stability in either experiment. XRT analysis of the biochars confirmed that the biochars were highly porous, with 48% and 57% porosity for the 400°C and 600°C biochars, respectively. More than 99% of internal pores of the biochar particles were connected to the surface, suggesting a potential role for biochars in improving soil water retention. However, the biochars were highly hydrophobic as demonstrated by the high contact angles when water was applied. We suggest that this hydrophobicity greatly diminished water infiltration into the biochar particles, prohibiting an effect on soil water retention. Our results indicate that, in addition to characterizing pore space, biochars should be analysed for hydrophobicity when assessing their capacity for improving soil physical properties.

Fate of five pharmaceuticals under different infiltration conditions for managed aquifer recharge.

PubMed

Silver, Matthew; Selke, Stephanie; Balsaa, Peter; Wefer-Roehl, Annette; Kübeck, Christine; Schüth, Christoph

2018-06-18

Infiltration of treated wastewater (TWW) to recharge depleted aquifers, often referred to as managed aquifer recharge, is a solution to replenish groundwater resources in regions facing water scarcity. We present a mass balance approach to infer the amounts of five pharmaceuticals (carbamazepine, diclofenac, fenoprofen, gemfibrozil, and naproxen) degraded in column experiments based on concentrations of pharmaceuticals in the aqueous and solid (sorbed) phases. Column experiments were conducted under three different conditions: continuous infiltration, wetting and drying cycles, and wetting and drying cycles with elevated concentrations of antibiotics (which may reduce microbially aided degradation of other compounds). A mass balance comparing pharmaceutical mass in the water phase over the 16-month duration of the experiments to mass sorbed to the soil was used to infer the mass of pharmaceuticals degraded. Results show sorption as the main attenuation mechanism for carbamazepine. About half of the mass of diclofenac was degraded with wetting and drying cycles, but no significant degradation was found for continuous infiltration, while 32% of infiltrated mass sorbed. Fenoprofen was degraded in the shallow and aerobic part of the soil, but degradation appeared to cease beyond 27 cm depth. Gemfibrozil attenuated through a combination of degradation and sorption, with slight increases in attenuation with depth from both mechanisms. Naproxen degraded progressively with depth, resulting in attenuation of >90% of the mass. In the column with elevated concentrations of antibiotics, the antibiotics attenuated to about 50% or less of inflow concentrations by 27 cm depth and within this zone, less degradation of the other compounds was observed. Copyright © 2018 Elsevier B.V. All rights reserved.

Rapid transport from the surface to wells in fractured rock: a unique infiltration tracer experiment.

PubMed

Levison, Jana K; Novakowski, Kent S

2012-04-01

A unique infiltration tracer experiment was performed whereby a fluorescent dye was applied to the land surface in an agricultural field, near Perth, Ontario, Canada, to simulate the transport of solutes to two pumped monitoring wells drilled into the granitic gneiss aquifer. This experiment, interpreted using the discrete-fracture capability of the numerical model HydroGeoSphere, showed that solute transport from the surface through thin soil (less than 2m) to wells in fractured bedrock can be extremely rapid (on the order of hours). Also, it was demonstrated that maximum concentrations of contaminants originating from the ground surface will not necessarily be the highest in the shallow aquifer horizon. These are important considerations for both private and government-owned drinking water systems that draw water from shallow fractured bedrock aquifers. This research illustrates the extreme importance of protecting drinking water at the source. Copyright © 2012 Elsevier B.V. All rights reserved.

The temperature dependence of ponded infiltration under isothermal conditions

USGS Publications Warehouse

Constantz, J.; Murphy, F.

1991-01-01

A simple temperature-sensitive modification to the Green and Ampt infiltration equation is described; this assumes that the temperature dependence of the hydraulic conductivity is reciprocally equal to the temperature dependence of the viscosity of liquid water, and that both the transmission zone saturation and the wetting front matric potential gradient are independent of temperature. This modified Green and Ampt equation is compared with ponded, isothermal infiltration experiments run on repacked columns of Olympic Sand and Aiken Loam at 5, 25, and 60??C. Experimental results showed increases in infiltration rates of at least 300% between 5 and 60??C for both soil materials, with subsequent increases in cumulative infiltration of even greater magnitudes for the loam. There is good agreement between measured and predicted initial infiltration rates at 25??C for both soil materials, yet at 60??C, the predicted results overestimate initial infiltration rates for the sand and underestimate initial rates for the loam. Measurements of the wetting depth vs. cumulative infiltration indicate that the transmission zone saturation increased with increasing temperature for both soil materials. In spite of this increased saturation with temperature, the final infiltration rates at both 25 and 60??C were predicted accurately using the modified Green and Ampt equation. This suggests that increased saturation occurred primarily in dead-end pore spaces, so that transmission zone hydraulic conductivities were unaffected by these temperature-induced changes in saturation. In conclusion, except for initial infiltration rates at 60??C, the measured influence of temperature on infiltration rates was fully accounted for by the temperature dependence of the viscosity of liquid water. ?? 1991.

Soft-bed experiments beneath Engabreen, Norway: Regelation, infiltration, basal slip and bed deformation

USGS Publications Warehouse

Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Cohen, D.; Moore, P.L.; Jackson, M.; Lappegard, G.; Kohler, J.

2007-01-01

To avoid some of the limitations of studying soft-bed processes through boreholes, a prism of simulated till (1.8 m ?? 1.6 m ?? 0.45 m) with extensive instrumentation was constructed in a trough blasted in the rock bed of Engabreen, a temperate glacier in Norway. Tunnels there provide access to the bed beneath 213 m of ice. Pore-water pressure was regulated in the prism by pumping water to it. During experiments lasting 7-12 days, the glacier regelated downward into the prism to depths of 50-80 mm, accreting ice-infiltrated till at rates predicted by theory. During periods of sustained high pore-water pressure (70-100% of overburden), ice commonly slipped over the prism, due to a water layer at the prism surface. Deformation of the prism was activated when this layer thinned to a sub-millimeter thickness. Shear strain in the till was pervasive and decreased with depth. A model of slip by ploughing of ice-infiltrated till across the prism surface accounts for the slip that occurred when effective pressure was sufficiently low or high. Slip at low effective pressures resulted from water-layer thickening that increased non-linearly with decreasing effective pressure. If sufficiently widespread, such slip over soft glacier beds, which involves no viscous deformation resistance, may instigate abrupt increases in glacier velocity.

Monitoring and modeling very large, rapid infiltration using geophysics during the 2014 Lower Colorado River pulse flow experiment

NASA Astrophysics Data System (ADS)

Kennedy, J.; Macy, J. P.; Callegary, J. B.; Lopez, J. R.

2014-12-01

In March and April 2014, an unprecedented experiment released over 100x106 cubic meters (81,000 acre-feet) of water from Morelos Dam into the normally-dry lower Colorado River below Yuma, Arizona, USA. More than half of the water released from Morelos Dam infiltrated within the limitrophe reach, a 32-km stretch between the Northern U.S.-Mexico International Boundary and the Southern International Boundary, a distance of just 32 river-kilometers. To characterize the spatial and temporal extent of infiltration, scientists from the US Geological Survey, Centro de Investigación Científica y de Educación Superior de Ensenada, Baja California, and Universidad Autónoma de Baja California carried out several geophysical surveys. Frequency-domain electromagnetic transects throughout the limitrophe reach showed that the subsurface comprised exclusively sandy material, with little finer-grained material to impede or otherwise influence infiltration. Direct current resistivity clearly imaged the rising water table near the stream channel. Both techniques provide valuable parameterization and calibration information for a surface-water/groundwater interaction model currently in development. Time-lapse gravity data were collected at 25 stations to expand the monitoring well network and provide storage-coefficient information for the groundwater model. Despite difficult field conditions, precise measurements of large gravity changes showed that changes in groundwater storage in the upper reach of the study area, where groundwater levels were highest, were constrained to the near vicinity of the river channel. Downstream near the Southern International Boundary, however, groundwater storage increased substantially over a large area, expanding into the regional aquifer that supplies irrigation water to surrounding agriculture.

Transmission losses, infiltration and groundwater recharge through ephemeral and intermittent streambeds: A review of applied methods

NASA Astrophysics Data System (ADS)

Shanafield, Margaret; Cook, Peter G.

2014-04-01

Aquifer recharge through ephemeral streambeds is believed to be a major source of groundwater recharge in arid areas; however, comparatively few studies quantify this streamflow recharge. This review synthesizes the available field-based aquifer recharge literature from arid regions around the world. Seven methods for quantifying ephemeral and intermittent stream infiltration and aquifer recharge are reviewed; controlled infiltration experiments, monitoring changes in water content, heat as a tracer of infiltration, reach length water balances, floodwave front tracking, groundwater mounding, and groundwater dating. The pertinent temporal and spatial scales, as well as the advantages and limitations of each method are illustrated with examples from the literature. Comparisons between the methods are used to highlight appropriate uses of each field method, with emphasis on the advantages of using multiple methods within a study in order to avoid the potential drawbacks inherent in any single method. Research needs are identified, including: quantitative uncertainty analysis, long-term data collection and analysis, understanding of the role of riparian vegetation, and reconciliation of transmission losses and infiltration estimates with actual aquifer recharge.

Analysis of Infiltration-Suction Response in Unsaturated Residual Soil Slope in Gelugor, Penang

NASA Astrophysics Data System (ADS)

Ashraf Mohamad Ismail, Mohd; Hasliza Hamzah, Nur; Min, Ng Soon; Hazreek Zainal Abidin, Mohd; Tajudin, Saiful Azhar Ahmad; Madun, Aziman

2018-04-01

Rainfall infiltration on residual soil slope may impair slope stability by altering the pore-water pressure in the soil. A study has been carried out on unsaturated residual soil slope in Gelugor, Penang to determine the changes in matric suction of residual soils at different depth due to rainwater infiltration. The sequence of this study includes the site investigation, field instrumentation, laboratory experiment and numerical modeling. Void ratio and porosity of soil were found to be decreasing with depth while the bulk density and dry density of soil increased due to lower porosity of soil at greater depth. Soil infiltration rate and matric suction of all depths decrease with the increase of volumetric water content as well as the degree of saturation. Numerical modeling was used to verify and predict the relationship between infiltration-suction response and degree of saturation. Numerical models can be used to integrate the rainfall scenarios into quantitative landslide hazard assessments. Thus, development plans and mitigation measures can be designed for estimated impacts from hazard assessments based on collected data.

Aquifer recharge from infiltration basins in a highly urbanized area: the river Po Plain (Italy)

NASA Astrophysics Data System (ADS)

Masetti, M.; Nghiem, S. V.; Sorichetta, A.; Stevenazzi, S.; Santi, E. S.; Pettinato, S.; Bonfanti, M.; Pedretti, D.

2015-12-01

Due to the extensive urbanization in the Po Plain in northern Italy, rivers need to be managed to alleviate flooding problems while maintaining an appropriate aquifer recharge under an increasing percentage of impermeable surfaces. During the PO PLain Experiment field campaign in July 2015 (POPLEX 2015), both active and under-construction infiltration basins have been surveyed and analyzed to identify appropriate satellite observations that can be integrated to ground based monitoring techniques. A key strategy is to have continuous data time series on water presence and level within the basin, for which ground based monitoring can be costly and difficult to be obtained consistently.One of the major and old infiltration basin in the central Po Plain has been considered as pilot area. The basin is active from 2003 with ground based monitoring available since 2009 and supporting the development of a calibrated unsaturated-saturated two-dimensional numerical model simulating the infiltration dynamics through the basin.A procedure to use satellite data to detect surface water change is under development based on satellite radar backscatter data with an appropriate incidence angle and polarization combination. An advantage of satellite radar is that it can observe surface water regardless of cloud cover, which can be persistent during rainy seasons. Then, the surface water change is correlated to the reservoir water stage to determine water storage in the basin together with integrated ground data and to give quantitative estimates of variations in the local water cycle.We evaluated the evolution of the infiltration rate, to obtain useful insights about the general recharge behavior of basins that can be used for informed design and maintenance. Results clearly show when the basin becomes progressively clogged by biofilms that can reduce the infiltration capacity of the basin by as much as 50 times compared to when it properly works under clean conditions.

Aquifer recharge with stormwater runoff in urban areas: Influence of vadose zone thickness on nutrient and bacterial transfers from the surface of infiltration basins to groundwater.

PubMed

Voisin, Jérémy; Cournoyer, Benoit; Vienney, Antonin; Mermillod-Blondin, Florian

2018-10-01

Stormwater infiltration systems (SIS) have been built in urban areas to reduce the environmental impacts of stormwater runoff. Infiltration basins allow the transfer of stormwater runoff to aquifers but their abilities to retain contaminants depend on vadose zone properties. This study assessed the influence of vadose zone thickness (VZT) on the transfer of inorganic nutrients (PO 4 3- , NO 3 - , NH 4 + ), dissolved organic carbon (total -DOC- and biodegradable -BDOC-) and bacteria. A field experiment was conducted on three SIS with a thin vadose zone (<3 m) and three SIS with a thick vadose zone (>10 m). Water samples were collected at three times during a rainy period of 10 days in each infiltration basin (stormwater runoff), in the aquifer impacted by infiltration (impacted groundwater) and in the same aquifer but upstream of the infiltration area (non-impacted groundwater). Inorganic nutrients, organic matter, and dissolved oxygen (DO) were measured on all water samples. Bacterial community structures were investigated on water samples through a next-generation sequencing (NGS) scheme of 16S rRNA gene amplicons (V5-V6). The concentrations of DO and phosphate measured in SIS-impacted groundwaters were significantly influenced by VZT due to distinct biogeochemical processes occurring in the vadose zone. DOC and BDOC were efficiently retained in the vadose zone, regardless of its thickness. Bacterial transfers to the aquifer were overall low, but data obtained on day 10 indicated a significant bacterial transfer in SIS with a thin vadose zone. Water transit time and water saturation of the vadose zone were found important parameters for bacterial transfers. Most bacterial taxa (>60%) from impacted groundwaters were not detected in stormwater runoff and in non-impacted groundwaters, indicating that groundwater bacterial communities were significantly modified by processes associated with infiltration (remobilization of bacteria from vadose zone and/or species sorting). Copyright © 2018 Elsevier B.V. All rights reserved.

Sensitivity of Vadose Zone Water Fluxes to Climate Shifts in Arid Settings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfletschinger, H.; Prömmel, K.; Schüth, C.

2014-01-01

Vadose zone water fluxes in arid settings are investigated regarding their sensitivity to hydraulic soil parameters and meteorological data. The study is based on the inverse modeling of highly defined soil column experiments and subsequent scenario modeling comparing different climate projections for a defined arid region. In arid regions, groundwater resources are prone to depletion due to excessive water use and little recharge potential. Especially in sand dune areas, groundwater recharge is highly dependent on vadose zone properties and corresponding water fluxes. Nevertheless, vadose zone water fluxes under arid conditions are hard to determine owing to, among other reasons, deepmore » vadose zones with generally low fluxes and only sporadic high infiltration events. In this study, we present an inverse model of infiltration experiments accounting for variable saturated nonisothermal water fluxes to estimate effective hydraulic and thermal parameters of dune sands. A subsequent scenario modeling links the results of the inverse model with projections of a global climate model until 2100. The scenario modeling clearly showed the high dependency of groundwater recharge on precipitation amounts and intensities, whereas temperature increases are only of minor importance for deep infiltration. However, simulated precipitation rates are still affected by high uncertainties in the response to the hydrological input data of the climate model. Thus, higher certainty in the prediction of precipitation pattern is a major future goal for climate modeling to constrain future groundwater management strategies in arid regions.« less

Removal of cyanobacterial toxins by sediment passage

NASA Astrophysics Data System (ADS)

Gruetzmacher, G.; Boettcher, G.; Chorus, I.; Bartel, H.

2003-04-01

Cyanbacterial toxins ("Cyanotoxins") comprise a wide range of toxic substances produced by cyanobacteria ("blue-green algae"). Cyanobacteria occur in surface water word wide and can be found in high concentrations during so-called algal blooms when conditions are favourable (e.g. high nutrient levels, high temperatures). Some cyanobacteria produce hepato- or neurotoxins, of which the hepatotoxic microcystins are the most common in Germany. The WHO guideline value for drinking water was set at 1 μg/L. However, maximum concentrations in surface water can reach 25 mg/L, so that a secure method for toxin elimination has to be found when this water is used as source water for drinking water production. In order to assess if cyanotoxins can be removed by sediment passage the German Federal Environmental Agency (UBA) conducted laboratory- and field scale experiments as well as observations on bank filtration field sites. Laboratory experiments (batch- and column experiments for adsorption and degradation parameters) were conducted in order to vary a multitude of experimental conditions. These experiments were followed by field scale experiments on the UBA's experimental field in Berlin. This plant offers the unique possibility to conduct experiments on the behaviour of various agents - such as harmful substances - during infiltration and bank filtration under well-defined conditions on a field scale, and without releasing these substances to the environment. Finally the development of microcystin concentrations was observed between infiltrating surface water and a drinking water well along a transsecte of observation wells. The results obtained show that infiltration and bank filtration normally seem to be secure treatment methods for source water contaminated by microcystins. However, elimination was shown to be difficult under the following circumstances: - dying cyanobacterial population due to insufficient light and / or nutrients, low temperatures or application of algizides (high amount of extracellular microcystins), - sandy material with low shares of clay and silt (little adsorption), - low temperatures (delayed biodegradation), - anoxic conditions (delayed biodegradation), - missing clogging layer or "schmutzdecke" (little bacteria), - no previous contact to microcystins (non adapted bacteria). It is therefore the aim of a new project financed by the KompetenzZentrum Wasser Berlin (KWB) to focus on these critical circumstances in order to find out how to optimise artificial recharge and bank filtration regarding microcystin elimination.

Dynamics of an experimental unconfined aquifer

NASA Astrophysics Data System (ADS)

Lajeunesse, E.; Guérin, A.; Devauchelle, O.

2015-12-01

During a rain event, water infiltrates into the ground where it flows slowly towards rivers. We use a tank filled with glass beads to simulate this process in a simplified laboratory experiment. A sprinkler pipe generates rain, which infiltrates into the porous material. Groundwater exits this laboratory aquifer through one side of the tank. The resulting water discharge increases rapidly during rainfall, and decays slowly after the rain has stopped.A theoretical analysis based on Darcy's law and the shallow-water approximation reveals two asymptotic regimes. At the beginning of a rain event, the water discharge increases linearly with time, with a slope proportional to the rainfall rate at the power of 3/2. Long after the rain has stopped, it decreases as the inverse time squared, as predicted by Polubarinova-Kochina (1962). These predictions compare well against our experimental data.Field measurements from two distinct catchments exhibit the same asymptotic behaviours as our experiment. This observation suggests that, despite the simplicity of the setup, our experimental results could be extended to natural groundwater flows.

Vegetation effects on event water dynamics - Insights from in-situ stable isotope observations and dye patterns

NASA Astrophysics Data System (ADS)

Volkmann, Till; Haberer, Kristine; Gessler, Arthur; Weiler, Markus

2014-05-01

The predicted changes of climate and land-use could have drastic effects on the water balance of ecosystems, particularly under frequent drought and subsequent rewetting conditions. Yet, inference of these effects and related consequences for the structure and functioning of ecosystems, groundwater recharge, leaching of nutrients and pollutants, drinking water availability, and the water cycle is currently impeded by gaps in our understanding of the manifold interactions between vegetation and soil water dynamics. While plants require water and nutrients, they also exert, for instance, important below-ground controls on the distribution and movement of water and chemicals in the rooted soil horizons via uptake and redistribution of water, modification of soil hydraulic properties, and formation of conduits for rapid preferential water flow. This work aims to contribute to fill existing gaps by assessing the effects of different plant types and their rooting systems on the soil water dynamics. Therefore, we conducted artificial drought and subsequent rewetting experiments using isotopically and dye (Brilliant Blue FCF) labeled water on plots of various surface cover (bare soil, grass, beech, oak, vine) established on relatively homogeneous luvisol on loess in southwestern Germany. Detailed insight into the short-term dynamics of event water infiltration and root uptake during the field experiments was facilitated by the application of novel techniques for high-frequency in-situ monitoring of stable isotope signatures in pore and transpiration water using commercial laser-based spectrometers, augmenting conventional observations of soil physicochemical states (soil water content, matric potential, electrical conductivity). The temporal point information is complemented by dye staining profiles, providing a detailed picture of spatial infiltration patterns, and by root density observations. The results of the experiments allow for a comprehensive spatiotemporal characterization of the effects of differing vegetation cover and rooting systems on infiltration, preferential flow path characteristics, and water storage in the rooted soil horizons. This will contribute to an improved ability to estimate environmental change impacts on the fate of water, nutrients, and pollutants in this critical zone and associated feedbacks within the soil-vegetation-atmosphere system.

Effects of thinning intensities on soil infiltration and water storage capacity in a Chinese pine-oak mixed forest.

PubMed

Chen, Lili; Yuan, Zhiyou; Shao, Hongbo; Wang, Dexiang; Mu, Xingmin

2014-01-01

Thinning is a crucial practice in the forest ecosystem management. The soil infiltration rate and water storage capacity of pine-oak mixed forest under three different thinning intensity treatments (15%, 30%, and 60%) were studied in Qinling Mountains of China. The thinning operations had a significant influence on soil infiltration rate and water storage capacity. The soil infiltration rate and water storage capacity in different thinning treatments followed the order of control (nonthinning): <60%, <15%, and <30%. It demonstrated that thinning operation with 30% intensity can substantially improve soil infiltration rate and water storage capacity of pine-oak mixed forest in Qinling Mountains. The soil initial infiltration rate, stable infiltration rate, and average infiltration rate in thinning 30% treatment were significantly increased by 21.1%, 104.6%, and 60.9%, compared with the control. The soil maximal water storage capacity and noncapillary water storage capacity in thinning 30% treatment were significantly improved by 20.1% and 34.3% in contrast to the control. The soil infiltration rate and water storage capacity were significantly higher in the surface layer (0~20 cm) than in the deep layers (20~40 cm and 40~60 cm). We found that the soil property was closely related to soil infiltration rate and water storage capacity.

Rainfall simulation experiments: Influence of water temperature, water quality and plot design on soil erosion and runoff

NASA Astrophysics Data System (ADS)

Iserloh, Thomas; Pegoraro, Dominique; Schlösser, Angelika; Thesing, Hannah; Seeger, Manuel; Ries, Johannes B.

2015-04-01

Field rainfall simulators are designed to study soil erosion processes and provide urgently needed data for various geomorphological, hydrological and pedological issues. Due to the different conditions and technologies applied, there are several methodological aspects under review of the scientific community, particularly concerning design, procedures and conditions of measurement for infiltration, runoff and soil erosion. This study aims at contributing fundamental data for understanding rainfall simulations in depth by studying the effect of the following parameters on the measurement results: 1. Plot design - round or rectangular plot: Can we identify differences in amount of runoff and erosion? 2. Water quality: What is the influence of the water's salt load on interrill erosion and infiltration as measured by rainfall experiments? 3. Water temperature: How much are the results conditioned by the temperature of water, which is subject to changes due to environmental conditions during the experiments? Preliminary results show a moderate increase of soil erosion with the water's salt load while runoff stays almost on the same level. With increasing water temperature, runoff increases continuously. At very high temperatures, soil erosion is clearly increased. A first comparison between round and rectangular plot indicates the rectangular plot to be the most suitable plot shape, but ambiguous results make further research necessary. The analysis of these three factors concerning their influence on runoff and erosion shows that clear methodological standards are necessary in order to make rainfall simulation experiments comparable.

Changes of physicochemical and microbiologicalparameters of infiltration water at Debina intake in Poznan, unique conditions - a flood

NASA Astrophysics Data System (ADS)

Kołaska, Sylwia; Jeż-Walkowiak, Joanna; Dymaczewski, Zbysław

2018-02-01

The paper presents characteristics of Debina infiltration intake which provides water for Poznan and neighbouring communes. The evaluation of effectiveness of infiltration process has been done based on the quality parameters of river water and infiltration water. The analysed water quality parameters are as follows: temperature, iron, manganese, DOCKMnO4, TOC, turbidity, colour, dissolved oxygen, free carbon dioxide, conductivity, total hardness, carbonate hardness, pH, heavy metals, detergents and microorganisms. The paper also includes an assessment of the impact of flood conditions on the quality of infiltration water and operation of infiltration intake. In this part of the paper the following parameters were taken into account: iron, manganese, DOCKMnO4, TOC, turbidity, colour, dissolved oxygen, free carbon dioxide, conductivity, total hardness, the total number of microorganisms in 36°C (mesophilic), the total number of microorganisms in 22°C (psychrophilic), coli bacteria, Clostridium perfringens, Escherichia coli, Enterococci. Analysis of the effects of flood on infiltration process leads to the following conclusions: the deterioration of infiltration water quality was due to the deterioration of river water quality, substantial shortening of groundwater passage and partial disappearance of the aeration zone. The observed deterioration of infiltration water quality did not affect the treated water quality, produced at water treatment plant.

Snowmelt water drives higher soil erosion than rainfall water in a mid-high latitude upland watershed

NASA Astrophysics Data System (ADS)

Wu, Yuyang; Ouyang, Wei; Hao, Zengchao; Yang, Bowen; Wang, Li

2018-01-01

The impacts of precipitation and temperature on soil erosion are pronounced in mid-high latitude areas, which lead to seasonal variations in soil erosion. Determining the critical erosion periods and the reasons behind the increased erosion loads are essential for soil management decisions. Hence, integrated approaches combining experiments and modelling based on field investigations were applied to investigate watershed soil erosion characteristics and the dynamics of water movement through soils. Long-term and continuous data for surface runoff and soil erosion variation characteristics of uplands in a watershed were observed via five simulations by the Soil and Water Assessment Tool (SWAT). In addition, laboratory experiments were performed to quantify the actual soil infiltrabilities in snowmelt seasons (thawed treatment) and rainy seasons (non-frozen treatment). The results showed that over the course of a year, average surface runoff and soil erosion reached peak values of 31.38 mm and 1.46 t ha-1 a-1, respectively, in the month of April. They also ranked high in July and August, falling in the ranges of 23.73 mm to 24.91 mm and 0.55 t ha-1 a-1 to 0.59 t ha-1 a-1, respectively. With the infiltration time extended, thawed soils showed lower infiltrabilities than non-frozen soils, and the differences in soil infiltration amounts between these two were considerable. These results highlighted that soil erosion was very closely and positively correlated with surface runoff. Soil loss was higher in snowmelt periods than in rainy periods due to the higher surface runoff in early spring, and the decreased soil infiltrability in snowmelt periods contributed much to this higher surface runoff. These findings are helpful for identification of critical soil erosion periods when making soil management before critical months, especially those before snowmelt periods.

Effect of Fruits Waste in Biopore Infiltration Hole Toward The Effectiveness of Water Infiltration Rate on Baraya Campus Land of Hasanuddin University

NASA Astrophysics Data System (ADS)

Santosa, Slamet

2018-03-01

The infiltration of water into the soil decreases due to the transfer of soill function or the lack of soil biopores. This study aims to determine the effectiveness of the use of fruits waste toward the water infiltration rate. Observation of the water level decrease is done every 5 minutes interval. Observation of biopore water infiltration rate was done after fruits waste decomposed for 15 and 30 days. Result of standard water infiltration rate at the first of 5 minutes is 2.18 mm/min, then decreases at interval of 5 minutes on next time as the soil begins to saturate the water. Baraya campus soil observed in soil depths of 100cm has a dusty texture character, grayish brown color and clumping structure. Soil character indicates low porosity. While biopore water infiltration rate at the first of 5 minute interval is 6.61and 6.95 mm/min on banana waste; 5.55 and 6.61mm/min on papaya waste and 4.26 and 5.39 mm/min on mango waste. The effectiveness of water infiltration rate is 44.45% and 41.93% on banana; 44.61% and 30.09% on papaya and 15.79% and 28.36% on mango. Study concluded that banana waste causes the water infiltration rate most effective in biopore infiltration hole.

THE VELOCITY OF DNAPL FINGERING IN WATER-SATURATED POROUS MEDIA LABORATORY EXPERIMENTS AND A MOBILE-IMMOBILE-ZONE MODEL. (R826157)

EPA Science Inventory

Dense nonaqueous phase liquids (DNAPLs) are immiscible with water and can give rise to highly fingered fluid distributions when infiltrating through water-saturated porous media. In this paper, a conceptual mobile_¯immobile_¯zone (MIZ) model is pr...

Perfluorinated compounds in infiltrated river rhine water and infiltrated rainwater in coastal dunes.

PubMed

Eschauzier, Christian; Haftka, Joris; Stuyfzand, Pieter J; de Voogt, Pim

2010-10-01

Different studies have shown that surface waters contain perfluorinated compounds (PFCs) in the low ng/L range. Surface waters are used to produce drinking water and PFCs have been shown to travel through the purification system and form a potential threat to human health. The specific physicochemical properties of PFCs cause them to be persistent and some of them to be bioaccumulative and toxic in the environment. This study investigates the evolvement of PFC concentrations in Rhine water and rainwater during dune water infiltration processes over a transect in the dune area of the western part of The Netherlands. The difference between infiltrated river water and rainwater in terms of PFC composition was investigated. Furthermore, isomer profiles were investigated. The compound perfluorobutanesulfonate (PFBS) was found at the highest concentrations of all PFCs investigated, up to 37 ng/L in infiltrated river water (71 ± 13% of ΣPFCs). This is in contrast with the predominant occurrence of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonate (PFOS) reported in literature. The concentrations of PFBS found in infiltrated river Rhine water were significantly higher than those in infiltrated rainwater. For perfluorohexanesulfonate (PFHxS) the opposite was found: infiltrated rainwater contained more than infiltrated river water. The concentrations of PFOA, perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), PFBS, PFOS, and PFHxS in infiltrated river water showed an increasing trend with decreasing age of the water. The relative contribution of the branched PFOA and PFOS isomers to total concentrations of PFOA and PFOS showed a decreasing trend with decreasing age of the water.

Modelling the removal of p-TSA (para-toluenesulfonamide) during rapid sand filtration used for drinking water treatment.

PubMed

Meffe, Raffaella; Kohfahl, Claus; Holzbecher, Ekkehard; Massmann, Gudrun; Richter, Doreen; Dünnbier, Uwe; Pekdeger, Asaf

2010-01-01

A finite element model was set-up to determine degradation rate constants for p-TSA during rapid sand filtration (RSF). Data used for the model originated from a column experiment carried out in the filter hall of a drinking water treatment plant in Berlin (Germany). Aerated abstracted groundwater was passed through a 1.6m long column-shaped experimental sand filter applying infiltration rates from 2 to 6mh(-1). Model results were fitted to measured profiles and breakthrough curves of p-TSA for different infiltration rates using both first-order reaction kinetics and Michaelis-Menten kinetics. Both approaches showed that degradation rates varied both in space and time. Higher degradation rates were observed in the upper part of the column, probably related to higher microbial activity in this zone. Measured and simulated breakthrough curves revealed an adaption phase with lower degradation rates after infiltration rates were changed, followed by an adapted phase with more elevated degradation rates. Irrespective of the mathematical approach and the infiltration rate, degradation rates were very high, probably owing to the fact that filter sands have been in operation for decades, receiving high p-TSA concentrations with the raw water.

Quantification of dynamic soil - vegetation feedbacks following an isotopically labelled precipitation pulse

NASA Astrophysics Data System (ADS)

Piayda, Arndt; Dubbert, Maren; Siegwolf, Rolf; Cuntz, Matthias; Werner, Christiane

2017-04-01

The presence of vegetation alters hydrological cycles of ecosystems. Complex plant-soil interactions govern the fate of precipitation input and water transitions through ecosystem compartments. Disentangling these interactions is a major challenge in the field of ecohydrology and pivotal foundation for understanding the carbon cycle of semi-arid ecosystems. Stable water isotopes can be used in this context as tracer to quantify water movement through soil-vegetation-atmosphere interfaces. The aim of this study is to disentangle vegetation effects on soil water infiltration and distribution as well as dynamics of soil evaporation and grassland water-use in a Mediterranean cork-oak woodland during dry conditions. An irrigation experiment using δ18O-labeled water was carried out in order to quantify distinct effects of tree and herbaceous vegetation on infiltration and distribution of event water in the soil profile. Dynamic responses of soil and herbaceous vegetation fluxes to precipitation regarding event water-use, water uptake depth plasticity and contribution to ecosystem evapotranspiration were quantified. Total water loss to the atmosphere from bare soil was as high as from vegetated soil, utilizing large amounts of unproductive water loss for biomass production, carbon sequestration and nitrogen fixation. During the experiment no adjustments of main root water uptake depth to changes of water availability could be observed, rendering light to medium precipitation events under dry conditions useless. This forces understory plants to compete with adjacent trees for soil water in deeper soil layers. Thus understory plants are faster subject to chronic drought, leading to premature senescence at the onset of drought. Despite this water competition, the presence of Cork oak trees fosters infiltration to large degrees. That reduces drought stress, caused by evapotranspiration, due to favourable micro climatic conditions under tree crown shading. This study highlights complex soil-plant-atmosphere and inter-species interactions in both space and time controlling the fate of rain pulse transitions through a typical Mediterranean savannah ecosystem, disentangled by the use of stable water isotopes.

Effects of Thinning Intensities on Soil Infiltration and Water Storage Capacity in a Chinese Pine-Oak Mixed Forest

PubMed Central

Chen, Lili; Yuan, Zhiyou; Shao, Hongbo; Wang, Dexiang; Mu, Xingmin

2014-01-01

Thinning is a crucial practice in the forest ecosystem management. The soil infiltration rate and water storage capacity of pine-oak mixed forest under three different thinning intensity treatments (15%, 30%, and 60%) were studied in Qinling Mountains of China. The thinning operations had a significant influence on soil infiltration rate and water storage capacity. The soil infiltration rate and water storage capacity in different thinning treatments followed the order of control (nonthinning): <60%, <15%, and <30%. It demonstrated that thinning operation with 30% intensity can substantially improve soil infiltration rate and water storage capacity of pine-oak mixed forest in Qinling Mountains. The soil initial infiltration rate, stable infiltration rate, and average infiltration rate in thinning 30% treatment were significantly increased by 21.1%, 104.6%, and 60.9%, compared with the control. The soil maximal water storage capacity and noncapillary water storage capacity in thinning 30% treatment were significantly improved by 20.1% and 34.3% in contrast to the control. The soil infiltration rate and water storage capacity were significantly higher in the surface layer (0~20 cm) than in the deep layers (20~40 cm and 40~60 cm). We found that the soil property was closely related to soil infiltration rate and water storage capacity. PMID:24883372

Electrical resistivity tomography as monitoring tool for unsaturated zone transport: an example of preferential transport of deicing chemicals.

PubMed

Wehrer, Markus; Lissner, Heidi; Bloem, Esther; French, Helen; Totsche, Kai Uwe

2014-01-01

Non-invasive spatially resolved monitoring techniques may hold the key to observe heterogeneous flow and transport behavior of contaminants in soils. In this study, time-lapse electrical resistivity tomography (ERT) was employed during an infiltration experiment with deicing chemical in a small field lysimeter. Deicing chemicals like potassium formate, which frequently impact soils on airport sites, were infiltrated during snow melt. Chemical composition of seepage water and the electrical response was recorded over the spring period 2010. Time-lapse electrical resistivity tomographs are able to show the infiltration of the melt water loaded with ionic constituents of deicing chemicals and their degradation product hydrogen carbonate. The tomographs indicate early breakthrough behavior in parts of the profile. Groundtruthing with pore fluid conductivity and water content variations shows disagreement between expected and observed bulk conductivity. This was attributed to the different sampling volume of traditional methods and ERT due to a considerable fraction of immobile water in the soil. The results show that ERT can be used as a soil monitoring tool on airport sites if assisted by common soil monitoring techniques.

Hydraulic characteristics and nutrient transport and transformation beneath a rapid infiltration basin, Reedy Creek Improvement District, Orange County, Florida

USGS Publications Warehouse

Sumner, D.M.; Bradner, L.A.

1996-01-01

The Reedy Creek Improvement District disposes of about 7.5 million gallons per day (1992) of reclaimed water through 85 1-acre rapid infiltration basins within a 1,000-acre area of sandy soils in Orange County, Florida. The U.S. Geological Survey conducted field experiments in 1992 at an individual basin to examine and better understand the hydraulic characteristics and nutrient transport and transformation of reclaimed water beneath a rapid infiltration basin. At the time, concentrations of total nitrogen and total phosphorus in reclaimed water were about 3 and 0.25 milligrams per liter, respectively. A two-dimensional, radial, unsaturated/saturated numerical flow model was applied to describe the flow system beneath a rapid infiltration basin under current and hypothetical basin loading scenarios and to estimate the hydraulic properties of the soil and sediment beneath a basin. The thicknesses of the unsaturated and saturated parts of the surficial aquifer system at the basin investigated were about 37 and 52 feet, respectively. The model successfully replicated the field-monitored infiltration rate (about 5.5 feet per day during the daily flooding periods of about 17 hours) and ground-water mounding response during basin operation. Horizontal and vertical hydraulic conductivity of the saturated part of the surficial aquifer system were estimated to be 150 and 45 feet per day, respectively. The field-saturated vertical hydraulic conductivity of the shallow soil, estimated to be about 5.1 feet per day, was considered to have been less than the full- saturation value because of the effects of air entrapment. Specific yield of the surficial aquifer was estimated to be 0.41. The upper 20 feet of the basin subsurface profile probably served as a system control on infiltration because of the relatively low field-saturated, vertical hydraulic conductivity of the sediments within this layer. The flow model indicates that, in the vicinity of the basin, flow in the deeper, saturated zone was relatively slow compared to the more vigorous flow in the shallow saturated zone. The large radial component of flow below the water table in the vicinity of the basin implies that reclaimed water moves preferentially in the shallow part of the saturated zone upon reaching the water table. Therefore, there may be some vertical stratification in the saturated zone, with recently infiltrated water overlying ambient water. The infiltration capacity at the basin would be unaffected by a small (less than 10 feet) increase in background water-table altitude, because the water table would remain below the system control on infiltration. However, water-table rises of 15 and 20 feet were estimated to reduce the infiltration capacity of the basin by 8 and 25 percent, respectively. Model simulations indicate that increasing ponded depth within the basin from 4 to 12 inches and from 4 to 24 inches would increase basin infiltration capacity by less than 6 and 11 percent, respectively. A loading strategy at the basin that relies on long, uninterrupted flooding was shown to offer the possibility of inducing a more anaerobic environment conducive to denitrification while maintaining reclaimed-water disposal capacity. Field measurements indicated that transient, elevated concentrations or "spikes" of nitrate (as high as 33 milligrams per liter as nitrogen) occurred at the leading edge of the infiltrating water and in the shallow saturated zone following a prolonged basin rest period. This phenomenon probably is the result of mineralization and nitrification of organic nitrogen retained with the subsurface during earlier basin loading events. The organic nitrogen was retained in the shallow soil (due to adsorption/straining) and the shallow saturated zone following a prolonged basin rest period. This phenomenon probably is the result of mineralization and nitrification of organic nitrogen retained within the subsurface during earlier basin loading event

Effect of the method of estimation of soil saturated hydraulic conductivity with regards to the design of stormwater infiltration trenches

NASA Astrophysics Data System (ADS)

Paiva coutinho, Artur; Predelus, Dieuseul; Lassabatere, Laurent; Ben Slimene, Erij; Celso Dantas Antonino, Antonio; Winiarski, Thierry; Joaquim da Silva Pereira Cabral, Jaime; Angulo-Jaramillo, Rafael

2014-05-01

Best management practices are based on the infiltration of stormwater (e.g. infiltration into basins or trenches) to reduce the risk of flooding of urban areas. Proper estimations of saturated hydraulic conductivity of the vadose zone are required to avoid inappropriate design of infiltration devices. This article aims at assessing (i) the method-dependency of the estimation of soils saturated hydraulic conductivity and (ii) the consequences of such dependency on the design of infiltration trenches. This is illustrated for the specific case of an infiltration trench to be constructed to receive stormwater from a specific parking surface, 250 m2 in area, in Recife (Brazil). Water infiltration experiments were conducted according to the Beerkan Method, i.e. application of a zero water pressure head through a disc source (D=15 cm) and measures of the amount of infiltrated water with time. Saturated hydraulic conductivity estimates are derived from the analysis of these infiltration tests using several different conceptual approaches: one-dimensional models of Horton(1933) and Philip(1957), three-dimensional methods recently developed (Lassabatere et al., 2006, Wu et al., 1999, and Bagarello et al., 2013) and direct 3-dimensional numerical inversion. The estimations for saturated hydraulic conductivity ranged between 65.5 mm/h and 94 mm/h for one-dimensional methods, whereas using three-dimensional methods saturated hydraulic conductivity ranged between 15.6 mm/h and 50 mm/h. These results shows the need for accounting for 3D geometry, and more generally, the physics of water infiltration in soils, if a proper characterization of soil saturated hydraulic conductivity is targeted. In a second step, each estimate of the saturated hydraulic conductivity was used to calculate the stormwater to be stored in the studied trench for several rainfall events of recurrence intervals of 2 to 25 years. The calculation of these volumes showed a great sensitivity with regards to the estimated values of saturated hydraulic conductivity. The designed volumes of the trench vary from 8.3 m3 to 15.9 m3 for one-dimensional methods and 11.9 m3 to 24.5 m3 for three-dimensional methods, respectively. The results show that any miss-estimation of the saturated hydraulic conductivity of soils may drastically impact the design of infiltration devices and the related extra-costs. Bagarello, B.; Castellini, M.; Di Prima,S.;Giordano ,G.; Iovino, M. (2013). Testing a simplified approach to determine field saturated soil hydraulic conductivity. Procedia Environmental Sciences 19 ( 2013 ) 599 - 608 Horton, R. (1933). The role of infiltration in the hydrologic cycle. American Geophysical Union Transactions 14, 446-460. Lassabatère, L.; Angulo-Jaramillo, R.; Soria, J.M.; Cuenca, R.; Braud, I.; Haverkamp, R.(2006). Beerkan estimation of soil transfer parameters through infiltration experiments - BEST. Soil Science Society of American Journal, Madison, v.70, p.521-532, 2006. Philip, J.R. (1957). The theory of Infiltration: 5. The Influence of the Initial Moisture Content. Soil Science, v.4, n.84, p.329-339, 1957. Wu, L.; Pan, L.; Mitchell, J.; Sanden, B. (1999). Measuring satured hydraulic conductivity using a generalized solution for single-ringle infiltrometers. Soil Sci.Soc.Am.J.63, 788-792

Experimental evaluation of four infiltration models for calcareous soil irrigated with treated untreated grey water and fresh water

NASA Astrophysics Data System (ADS)

Gharaibeh, M. A.; Eltaif, N. I.; Alrababah, M. A.; Alhamad, M. N.

2009-04-01

Infiltration is vital for both irrigated and rainfed agriculture. The knowledge of infiltration characteristics of a soil is the basic information required for designing an efficient irrigation system. The objective of the present study was to model soil infiltration using four models: Green and Ampt, Horton, Kostaikov and modified Kostiakov. Infiltration tests were conducted on field plot irrigated with treated, untreated greywater and fresh water. The field water infiltration data used in these models were based on double ring infiltrometer tests conducted for 4 h. The algebraic parameters of the infiltration models and nonlinear least squares regression were fitted using measured infiltration time [I (t)] data. Among process-based infiltration models, the Horton model performed best and matched the measured I (t) data with lower sum of squares (SS).

Electrical resistivity imaging study of near-surface infiltration

NASA Astrophysics Data System (ADS)

Lampousis, Angelos

High resolution electrical resistivity images (ERI method) were obtained during vadose zone infiltration experiments on agricultural soils in cooperation with Cornell University's Agricultural Stewardship Program, Cooperative Extension of Suffolk County, Extension Education Center, Riverhead, New York [ as well as Cornell University's Long Island Horticultural Research & Extension Center (LIHREC) in Riverhead, New York]. One natural soil was also studied. Infiltration was monitored by means of image analysis of two-dimensional array resistivity generated by a Syscal Kid Switch resistivity system (Griffiths et al., 1990). The data was inverted with the computer program RES2DINV (Loke, 2004). The agricultural soils considered were Riverhead sandy loam (RdA), Haven loam (HaA), and Bridgehampton silt loam (BgA). The natural site was located in the Catskill Mountains of New York State. The soils there are classified as Schoharie silty clay loam. The electrical images of the three sites were compared against established soil properties, including particle size distribution, available water capacity, and soluble salts (from the literature), as well as against site-specific soil samples and penetrometer data, which were collected along with the geophysical measurements. This research evaluates the potential of acquiring high resolution, non-destructive measurements of infiltration in the uppermost 1.5 meter of the vadose zone. The results demonstrate that resistivity differences can detect infiltration in soils typical of the north-eastern United States. Temporal and spatial variations of soil water content in the upper 1.5 meters (relevant to agriculture) of the subsurface can be monitored successfully and non-destructively with ERI. The sensitivity of the method is higher in subsurface environments that demonstrate high overall apparent resistivity values (e.g. high sand content). Under conditions of increased soil heterogeneity, instead of the formation of a continuous water plume as occurred in the homogeneous agricultural soils, the location of the infiltrated water seems to be highly influenced by the soil heterogeneity, and the water front is scattered into discontinuous layers and travels in additional directions. The geophysical results during infiltration correlate well with soil compaction data. It follows that the ERI method can be used as a proxy for soil compaction and water content variations in agricultural applications. In a natural environment, ERI successfully maps the tree root zone of mature trees. Applications include continuous water content monitoring in high value cash crops, such as viticulture (precision agriculture).

Evaluation of infiltration for the determination of palms water needs

NASA Astrophysics Data System (ADS)

Benlarbi, Dalila; Boutaoutaou, Djamel; Saggaï, Sofiane

2018-05-01

In arid climate conditions, irrigation water requirements increase, but available water resources are limited. And therefore the Saharan regions, large consumers of water can be seriously threatened if they do not make the necessary to become as parsimonious as allow the irrigation techniques whose technological aspect on their improvement has been privileged until now but all the problems are not solved. The objective of this work is to know the process of infiltration of water in the soil, i.e.: to try to determine exactly its value with obtaining the best combination (flow of entry, board length and irrigation time) in order to have a more or less uniform distribution in the soil and especially by avoiding significant water losses that would cause rise in the water table. The infiltration will allow us to calculate at any point the dose of water received that we will compare with the needs of the date palm. For this purpose; we varied the input flow for a constant board length. Then we varied the board length for a constant input rate. In both cases we varied the irrigation time according to the water requirements of the date palm. The flow remains of course constant during the entire feeding period. This study is primarily experimental and aims to meet practical applications but not immediately because it is necessary to continue the experiments with several other combinations to achieve practical results.

Water extracts from winery by-products as tobacco defense inducers.

PubMed

Benouaret, Razik; Goujon, Eric; Trivella, Aurélien; Richard, Claire; Ledoigt, Gérard; Joubert, Jean-Marie; Mery-Bernardon, Aude; Goupil, Pascale

2014-10-01

Water extracts from winery by-products exhibited significant plant defense inducer properties. Experiments were conducted on three marc extracts containing various amounts of polyphenols and anthocyanins. Infiltration of red, white and seed grape marc extracts into tobacco leaves induced hypersensitive reaction-like lesions with cell death evidenced by Evans Blue staining. The infiltration zones and the surrounding areas revealed accumulation of autofluorescent compounds under UV light. Leaf infiltration of the three winery by-product extracts induced defense gene expression. The antimicrobial PR1, β-1,3-glucanase PR2, and chitinase PR3 target genes were upregulated locally in tobacco plants following grape marc extract treatments. The osmotin PR5 transcripts accumulated as well in red marc extract treated-tobacco leaves. Overall, the winery by-product extracts elicited an array of plant defense responses making the grape residues a potential use of high value compounds.

Hydrogeophysical monitoring of water infiltration processes

NASA Astrophysics Data System (ADS)

Bevilacqua, Ivan; Cassiani, Giorgio; Deiana, Rita; Canone, Davide; Previati, Maurizio

2010-05-01

Non-invasive subsurface monitoring is growing in the last years. Techniques like ground-penetrating radar (GPR) and electrical resistivity tomography (ERT) can be useful in soil water content monitoring (e.g., Vereecken et al., 2006). Some problems remain (e.g. spatial resolution), but the scale is consistent with many applications and hydrological models. The research has to to provide even more quantitative tools, without remaining in the qualitative realm. This is a very crucial step in the way to provide data useful for hydrological modeling. In this work a controlled field infiltration experiment has been done in August 2009 in the experimental site of Grugliasco, close to the Agricultural Faculty of the University of Torino, Italy. The infiltration has been monitored in time lapse by ERT, GPR, and TDR (Time Domain Reflectometry). The sandy soil characteristics of the site has been already described in another experiment [Cassiani et al. 2009a].The ERT was èperformed in dipole-dipole configuration, while the GPR had 100 MHz and 500 MHz antennas in WARR configuration. The TDR gages had different lengths. The amount of water which was sprinkled was also monitored in time.Irrigation intensity has been always smaller than infiltration capacity, in order not toh ave any surface ponding. Spectral induced polarization has been used to infer constitutive parameters from soil samples [Cassiani et al. 2009b]. 2D Richards equation model (Manzini and Ferraris, 2004) has been then calibrated with the measurements. References. Cassiani, G., S. Ferraris, M. Giustiniani, R. Deiana and C.Strobbia, 2009a, Time-lapse surface-to-surface GPR measurements to monitor a controlled infiltration experiment, in press, Bollettino di Geofisica Teorica ed Applicata, Vol. 50, 2 Marzo 2009, pp. 209-226. Cassiani, G., A. Kemna, A.Villa, and E. Zimmermann, 2009b, Spectral induced polarization for the characterization of free-phase hydrocarbon contamination in sediments with low clay content, Near Surface Geophysics, special issue on Hydrogeophysics, p. 547-562. Manzini G., and Ferraris S. 2004. Mass-conservative finite-volume methods on 2-D unstructured grids for the Richards equation, 'Advances in Water Resources' 27(12):1199-1215, 2004. content with ground penetrating radar: A review. Vadose Zone Journal 2, 476-491. Vereecken H., Binley A., Cassiani G., Kharkhordin I., Revil A. and Titov K. 2006. Applied Hydrogeophysics. Springer-Verlag.

Spatial multi-criteria analysis for selecting potential sites for aquifer recharge via harvesting and infiltration of surface runoff in north Jordan

NASA Astrophysics Data System (ADS)

Steinel, Anke; Schelkes, Klaus; Subah, Ali; Himmelsbach, Thomas

2016-11-01

In (semi-)arid regions, available water resources are scarce and groundwater resources are often overused. Therefore, the option to increase available water resources by managed aquifer recharge (MAR) via infiltration of captured surface runoff was investigated for two basins in northern Jordan. This study evaluated the general suitability of catchments to generate sufficient runoff and tried to identify promising sites to harvest and infiltrate the runoff into the aquifer for later recovery. Large sets of available data were used to create regional thematic maps, which were then combined to constraint maps using Boolean logic and to create suitability maps using weighted linear combination. This approach might serve as a blueprint which could be adapted and applied to similar regions. The evaluation showed that non-committed source water availability is the most restricting factor for successful water harvesting in regions with <200 mm/a rainfall. Experiences with existing structures showed that sediment loads of runoff are high. Therefore, the effectiveness of any existing MAR scheme will decrease rapidly to the point where it results in an overall negative impact due to increased evaporation if maintenance is not undertaken. It is recommended to improve system operation and maintenance, as well as monitoring, in order to achieve a better and constant effectiveness of the infiltration activities.

Multiphase flow experiments, mathematical modeling and numerical simulation of the water - gas - solute movement

NASA Astrophysics Data System (ADS)

Li, Y.; Ma, X.; Su, N.

2013-12-01

The movement of water and solute into and through the vadose zone is, in essence, an issue of immiscible displacement in pore-space network of a soil. Therefore, multiphase flow and transport in porous media, referring to three medium: air, water, and the solute, pose one of the largest unresolved challenges for porous medium fluid seepage. However, this phenomenon has always been largely neglected. It is expected that a reliable analysis model of the multi-phase flow in soil can truly reflect the process of natural movement about the infiltration, which is impossible to be observed directly. In such cases, geophysical applications of the nuclear magnetic resonance (NMR) provides the opportunity to measure the water movements into soils directly over a large scale from tiny pore to regional scale, accordingly enable it available both on the laboratory and on the field. In addition, the NMR provides useful information about the pore space properties. In this study, we proposed both laboratory and field experiments to measure the multi-phase flow parameters, together with optimize the model in computer programming based on the fractional partial differential equations (fPDE). In addition, we establish, for the first time, an infiltration model including solute flowing with water, which has huge influence on agriculture and soil environment pollution. Afterwards, with data collected from experiments, we simulate the model and analyze the spatial variability of parameters. Simulations are also conducted according to the model to evaluate the effects of airflow on water infiltration and other effects such as solute and absorption. It has significant meaning to oxygen irrigation aiming to higher crop yield, and shed more light into the dam slope stability. In summary, our framework is a first-time model added in solute to have a mathematic analysis with the fPDE and more instructive to agriculture activities.

Investigation of artificial recharge of aquifers in Nebraska

USGS Publications Warehouse

Lichtler, William F.; Stannard, David I.; Kouma, Edwin

1980-01-01

Progressive declines of ground-water levels in some areas of Nebraska prompted this investigation into the technical feasibility of recharging aquifers through wells, impoundments, pits, and canals. Information gained from a literature search and from preliminary tests was used to design several artificial-recharge experiments in Nebraska from 1977 to 1979. In well experiments, 0.46 billion gallons of water from an aquifer recharged by the Platte River was transported by pipeline and injected through a well into a sand and gravel aquifer near Aurora. Recharge was at about 730 gallons per minute during tests of 6- and 8-months duration. No evidence of clogging of the aquifer due to chemical reactions, air entrainment, or bacteria was detected in either test. In the 6-month test, evidence of clogging due to fine sediment in the recharge water was detected; however, analysis of this test indicated that recharge could have continued for several years before rehabilitation would have become necessary. Results of the 8-month test confirmed results of the earlier test until casing failure in the supply well and subsequent sediment deposition in the recharge well caused rapid water-level rise in the recharge well. In surface-spreading experiments, maximum infiltration rates from 24-foot-diameter ring infiltrometers near Aurora and Tryon were 0.4 and 11 feet per day, respectively. Results indicate that large-scale surface spreading is feasible only where low-permeability layers are absent in the subsurface. Infiltration rates from reuse pits ranged from 0.01 to 1.6 feet per day, indicating highly variable subsurface permeability. Flow measurements in an irrigation canal near Farwell indicate an infiltration rate of 0.37 feet per day. (USGS)

A cellular automata approach for modeling surface water runoff

NASA Astrophysics Data System (ADS)

Jozefik, Zoltan; Nanu Frechen, Tobias; Hinz, Christoph; Schmidt, Heiko

2015-04-01

This abstract reports the development and application of a two-dimensional cellular automata based model, which couples the dynamics of overland flow, infiltration processes and surface evolution through sediment transport. The natural hill slopes are represented by their topographic elevation and spatially varying soil properties infiltration rates and surface roughness coefficients. This model allows modeling of Hortonian overland flow and infiltration during complex rainfall events. An advantage of the cellular automata approach over the kinematic wave equations is that wet/dry interfaces that often appear with rainfall overland flows can be accurately captured and are not a source of numerical instabilities. An adaptive explicit time stepping scheme allows for rainfall events to be adequately resolved in time, while large time steps are taken during dry periods to provide for simulation run time efficiency. The time step is constrained by the CFL condition and mass conservation considerations. The spatial discretization is shown to be first-order accurate. For validation purposes, hydrographs for non-infiltrating and infiltrating plates are compared to the kinematic wave analytic solutions and data taken from literature [1,2]. Results show that our cellular automata model quantitatively accurately reproduces hydrograph patterns. However, recent works have showed that even through the hydrograph is satisfyingly reproduced, the flow field within the plot might be inaccurate [3]. For a more stringent validation, we compare steady state velocity, water flux, and water depth fields to rainfall simulation experiments conducted in Thies, Senegal [3]. Comparisons show that our model is able to accurately capture these flow properties. Currently, a sediment transport and deposition module is being implemented and tested. [1] M. Rousseau, O. Cerdan, O. Delestre, F. Dupros, F. James, S. Cordier. Overland flow modeling with the Shallow Water Equation using a well balanced numerical scheme: Adding efficiency or sum more complexity?. 2012. [2] Fritz R. Fiedler, J. A. Ramirez. A numerical method for simulating discontinuous shallow flow over an infiltrating surface. In. J. Numer. Mech. Fluids 200: 32: 219-240. [3] C. Mügler, O. Planchon, J. Patin, S. Weill, N. Silvera, P. Richard, E. Mouche. Comparison of Roughness models to simulate overland flow and tracer transport experiments under simulated rainfall at plot scale. Journal of Hydrology. 402 (2011) 25-40.

Grass mulching effect on infiltration, surface runoff and soil loss of three agricultural soils in Nigeria.

PubMed

Adekalu, K O; Olorunfemi, I A; Osunbitan, J A

2007-03-01

Mulching the soil surface with a layer of plant residue is an effective method of conserving water and soil because it reduces surface runoff, increases infiltration of water into the soil and retard soil erosion. The effectiveness of using elephant grass (Pennisetum purpureum) as mulching material was evaluated in the laboratory using a rainfall simulator set at rainfall intensities typical of the tropics. Six soil samples, two from each of the three major soil series representing the main agricultural soils in South Western Nigeria were collected, placed on three different slopes, and mulched with different rates of the grass. The surface runoff, soil loss, and apparent cumulative infiltration were then measured under each condition. The results with elephant grass compared favorably with results from previous experiments using rice straw. Runoff and soil loss decreased with the amount of mulch used and increased with slope. Surface runoff, infiltration and soil loss had high correlations (R = 0.90, 0.89, and 0.86, respectively) with slope and mulch cover using surface response analysis. The mean surface runoff was correlated negatively with sand content, while mean soil loss was correlated positively with colloidal content (clay and organic matter) of the soil. Infiltration was increased and soil loss was reduced greatly with the highest cover. Mulching the soils with elephant grass residue may benefit late cropping (second cropping) by increasing stored soil water for use during dry weather and help to reduce erosion on sloping land.

Infiltration and Evaporation of Diesel and Gasoline Droplets Spilled onto Concrete Pavement

NASA Astrophysics Data System (ADS)

Hilpert, M.; Adria-Mora, B.

2015-12-01

Pollution at gas stations due to small spills that occur during refueling of customer vehicles has received little attention. We have performed laboratory experiments in order to assess the processes of evaporation and infiltration of fuel spilled onto concrete samples. Changes in mass of both spilled diesel and gasoline droplets as a function of time have been analyzed. The infiltrated mass is affected by variations in humidity, among other parameters, which influence the amount of water condensed onto the concrete. Therefore, we used a humidity data logger and statistical tools to predict the evolution of the real mass of infiltrated fuel. The infiltrated mass roughly decreases exponentially, but the difference in behavior between both fuel types is important. The percentage of evaporated mass is much larger for gasoline, while infiltration is more significant for diesel. Also, the percentage of infiltrated liquid depends on the initial droplet mass. We also developed a multiphysics model, which couples pore-scale infiltration to turbulent atmospheric transport, to explain the experimental data. In conclusion, a substantial amount of fuel could both seep into the ground to contaminate groundwater and be released to the atmosphere. More studies are needed to quantify the public health implications of the released pollutants.

GROUND WATER CONTAMINATION POTENTIAL FROM STORMWATER INFILTRATION

EPA Science Inventory

Prior to urbanization, ground water recharge resulted from infiltration of precipitation through pervious surfaces, including grasslands and woods. This infiltration water was relatively uncontaminated. With urbanization, the permeable soil surface area through which recharge by...

Estimating the saturated soil hydraulic conductivity by the near steady-state phase of a beerkan infiltration run

NASA Astrophysics Data System (ADS)

Di Prima, Simone; Bagarello, Vincenzo; Iovino, Massimo

2017-04-01

Simple infiltration experiments carried out in the field allow an easy and inexpensive way of characterizing soil hydraulic behavior, maintaining the functional connection of the sampled soil volume with the surrounding soil. The beerkan method consists of a three-dimensional (3D) infiltration experiment at zero pressure head (Haverkamp et al., 1996). It uses a simple annular ring inserted to a depth of about 0.01 m to avoid lateral loss of the ponded water. Soil disturbance is minimized by the limited ring insertion depth. Infiltration time of small volumes of water repeatedly poured on the confined soil are measured to determine the cumulative infiltration. Different algorithms based on this methodology (the so-called BEST family of algorithms) were developed for the determination of soil hydraulic characteristic parameters (Bagarello et al., 2014a; Lassabatere et al., 2006; Yilmaz et al., 2010). Recently, Bagarello et al. (2014b) developed a Simplified method based on a Beerkan Infiltration run (SBI method) to determine saturated soil hydraulic conductivity, Ks, by only the transient phase of a beerkan infiltration run and an estimate of the α* parameter, expressing the relative importance of gravity and capillary forces during an infiltration process (Reynolds and Elrick, 1990). However, several problems yet arise with the existing BEST-algorithms and the SBI method, including (i) the need of supplementary field and laboratory measurements (Bagarello et al., 2013); (ii) the difficulty to detect a linear relationship between I / √t and √t in the early stage of the infiltration process (Bagarello et al., 2014b); (iii) estimation of negative Ks values for hydrophobic soils (Di Prima et al., 2016). In this investigation, a new Simplified method based on the analysis of the Steady-state Beerkan Infiltration run (SSBI method) was proposed and tested. In particular, analytical data were generated to simulate beerkan infiltration experiments for six contrasting soils (sand, S; loamy sand, LS; sandy loam, SAL; loam, L; silt loam, SIL and silty clay loam, SCL) from UNSODA database and different initial water contents. Comparison with other existing procedures were also carried out. The SSBI method allowed accurate estimation of saturated soil hydraulic conductivity of both field and analytically generated data. For analytically generated data, the most accurate predictions were obtained with the method 2 by Wu et al. (1999) for the S and LS soils (prediction errors not exceeding 3.8%) and with the SSBI method for the other four soils (error < 3.7%). Therefore, this last method performed better than the other tested methods in most cases. The analysis of the field data supported the usability of the SSBI method in different environments and conditions to obtain an acceptable prediction of Ks, i.e. similar to the one that can be obtained with the BEST-steady algorithm (Bagarello et al., 2014a). Finally, this investigation yielded encouraging signs on the applicability of the SSBI method for a trustworthy estimation of Ks by the near steady-state phase of a beerkan infiltration run. REFERENCES Bagarello, V., Castellini, M., Di Prima, S., Giordano, G., Iovino, M., 2013. Testing a Simplified Approach to Determine Field Saturated Soil Hydraulic Conductivity. Procedia Environmental Sciences 19, 599-608. doi:10.1016/j.proenv.2013.06.068 Bagarello, V., Di Prima, S., Iovino, M., 2014a. Comparing Alternative Algorithms to Analyze the Beerkan Infiltration Experiment. Soil Science Society of America Journal 78, 724. doi:10.2136/sssaj2013.06.0231 Bagarello, V., Di Prima, S., Iovino, M., Provenzano, G., 2014b. Estimating field-saturated soil hydraulic conductivity by a simplified Beerkan infiltration experiment. Hydrological Processes 28, 1095-1103. doi:10.1002/hyp.9649 Di Prima, S., Lassabatere, L., Bagarello, V., Iovino, M., Angulo-Jaramillo, R., 2016. Testing a new automated single ring infiltrometer for Beerkan infiltration experiments. Geoderma 262, 20-34. doi:10.1016/j.geoderma.2015.08.006 Haverkamp, R., Arrúe, J., Vandervaere, J., Braud, I., Boulet, G., Laurent, J., Taha, A., Ross, P., Angulo-Jaramillo, R., 1996. Hydrological and thermal behaviour of the vadose zone in the area of Barrax and Tomelloso (Spain): Experimental study, analysis and modeling. Project UE n. EV5C-CT 92, 00-90. Lassabatere, L., Angulo-Jaramillo, R., Soria Ugalde, J.M., Cuenca, R., Braud, I., Haverkamp, R., 2006. Beerkan Estimation of Soil Transfer Parameters through Infiltration Experiments—BEST. Soil Science Society of America Journal 70, 521. doi:10.2136/sssaj2005.0026 Reynolds, W.D., Elrick, D.E., 1990. Ponded Infiltration From a Single Ring: I. Analysis of Steady Flow. Soil Science Society of America Journal 54, 1233. doi:10.2136/sssaj1990.03615995005400050006x Wu, L., Pan, L., Mitchell, J., Sanden, B., 1999. Measuring Saturated Hydraulic Conductivity using a Generalized Solution for Single-Ring Infiltrometers. Soil Science Society of America Journal 63, 788. doi:10.2136/sssaj1999.634788x Yilmaz, D., Lassabatere, L., Angulo-Jaramillo, R., Deneele, D., Legret, M., 2010. Hydrodynamic Characterization of Basic Oxygen Furnace Slag through an Adapted BEST Method. Vadose Zone Journal 9, 107. doi:10.2136/vzj2009.0039

Comparing a simple methodology to evaluate hydrodynamic parameters with rainfall simulation experiments

NASA Astrophysics Data System (ADS)

Di Prima, Simone; Bagarello, Vincenzo; Bautista, Inmaculada; Burguet, Maria; Cerdà, Artemi; Iovino, Massimo; Prosdocimi, Massimo

2016-04-01

Studying soil hydraulic properties is necessary for interpreting and simulating many hydrological processes having environmental and economic importance, such as rainfall partition into infiltration and runoff. The saturated hydraulic conductivity, Ks, exerts a dominating influence on the partitioning of rainfall in vertical and lateral flow paths. Therefore, estimates of Ks are essential for describing and modeling hydrological processes (Zimmermann et al., 2013). According to several investigations, Ks data collected by ponded infiltration tests could be expected to be unusable for interpreting field hydrological processes, and particularly infiltration. In fact, infiltration measured by ponding give us information about the soil maximum or potential infiltration rate (Cerdà, 1996). Moreover, especially for the hydrodynamic parameters, many replicated measurements have to be carried out to characterize an area of interest since they are known to vary widely both in space and time (Logsdon and Jaynes, 1996; Prieksat et al., 1994). Therefore, the technique to be applied at the near point scale should be simple and rapid. Bagarello et al. (2014) and Alagna et al. (2015) suggested that the Ks values determined by an infiltration experiment carried applying water at a relatively large distance from the soil surface could be more appropriate than those obtained with a low height of water pouring to explain surface runoff generation phenomena during intense rainfall events. These authors used the Beerkan Estimation of Soil Transfer parameters (BEST) procedure for complete soil hydraulic characterization (Lassabatère et al., 2006) to analyze the field infiltration experiment. This methodology, combining low and high height of water pouring, seems appropriate to test the effect of intense and prolonged rainfall events on the hydraulic characteristics of the surface soil layer. In fact, an intense and prolonged rainfall event has a perturbing effect on the soil surface and, reasonably, it can better be represented by the high runs than the low runs (Alagna et al., 2015). Obviously, this methodology is also simpler than an approach involving soil characterization both before and after natural or simulated rainfall since it needs less equipment and field work. On the other hand, rainfall simulation experiments are more realistic and accurate, but also more sophisticated and costly (Cerdà, 1997). Rainfall simulation is often used to measure the infiltration process (e.g., Bhardwaj and Singh, 1992; Cerdà, 1999, 1997, 1996; Cerdà and Doerr, 2007; Iserloh et al., 2013; Liu et al., 2011; Tricker, 1979), and it has become an important method for assessing the subjects of soil erosion and soil hydrological processes (Iserloh et al., 2013). Its application allows a quick, specific and reproducible assessment of the meaning and impact of several factors, such as slope, soil type (infiltration, permeability), soil moisture, splash effect of raindrops (aggregate stability), surface structure, vegetation cover and vegetation structure (Bowyer-Bower and Burt, 1989). The objectives of this investigation are: (i) to compare infiltration rates measured by applying water at a relatively large distance from the soil surface with those obtained by rainfall simulation experiments and (ii) to verify if the Ks values determined with the BEST procedure are in line with the occurrence of runoff measured with a more robust methodology. Acknowledgements The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 603498 (RECARE project). References Alagna, V., Bagarello, V., Di Prima, S., Giordano, G., Iovino, M., 2015. Testing infiltration run effects on the estimated hydrodynamic parameters of a sandy-loam soil. Submitted to Geoderma. Bagarello, V., Castellini, M., Di Prima, S., Iovino, M., 2014. Soil hydraulic properties determined by infiltration experiments and different heights of water pouring. Geoderma 213, 492-501. doi:10.1016/j.geoderma.2013.08.032 Bhardwaj, A., Singh, R., 1992. Development of a portable rainfall simulator infiltrometer for infiltration, runoff and erosion studies. Agricultural Water Management 22, 235-248. doi:10.1016/0378-3774(92)90028-U Bouwer, H., 1966. Rapid field measurement of air entry value and hydraulic conductivity of soil as significant parameters in flow system analysis. Water Resour. Res. 2, 729-738. doi:10.1029/WR002i004p00729 Bowyer-Bower, T.A.S., Burt, T.P., 1989. Rainfall simulators for investigating soil response to rainfall. Soil Technology 2, 1-16. doi:10.1016/S0933-3630(89)80002-9 Cerdà, A., 1999. Simuladores de lluvia y su aplicación a la Geomorfologia: estado de la cuestión. Cuadernos de investigación geográfica 45-84. Cerdà, A., 1997. Seasonal changes of the infiltration rates in a Mediterranean scrubland on limestone. Journal of Hydrology 198, 209-225. doi:10.1016/S0022-1694(96)03295-7 Cerdà, A., 1996. Seasonal variability of infiltration rates under contrasting slope conditions in southeast Spain. Geoderma 69, 217-232. doi:10.1016/0016-7061(95)00062-3 Cerdà, A., Doerr, S.H., 2007. Soil wettability, runoff and erodibility of major dry-Mediterranean land use types on calcareous soils. Hydrol. Process. 21, 2325-2336. doi:10.1002/hyp.6755 Iserloh, T., Ries, J.B., Arnáez, J., Boix-Fayos, C., Butzen, V., Cerdà, A., Echeverría, M.T., Fernández-Gálvez, J., Fister, W., Geißler, C., Gómez, J.A., Gómez-Macpherson, H., Kuhn, N.J., Lázaro, R., León, F.J., Martínez-Mena, M., Martínez-Murillo, J.F., Marzen, M., Mingorance, M.D., Ortigosa, L., Peters, P., Regüés, D., Ruiz-Sinoga, J.D., Scholten, T., Seeger, M., Solé-Benet, A., Wengel, R., Wirtz, S., 2013. European small portable rainfall simulators: A comparison of rainfall characteristics. CATENA 110, 100-112. doi:10.1016/j.catena.2013.05.013 Lassabatère, L., Angulo-Jaramillo, R., Soria Ugalde, J.M., Cuenca, R., Braud, I., Haverkamp, R., 2006. Beerkan Estimation of Soil Transfer Parameters through Infiltration Experiments - BEST. Soil Science Society of America Journal 70, 521. doi:10.2136/sssaj2005.0026 Liu, H., Lei, T.W., Zhao, J., Yuan, C.P., Fan, Y.T., Qu, L.Q., 2011. Effects of rainfall intensity and antecedent soil water content on soil infiltrability under rainfall conditions using the run off-on-out method. Journal of Hydrology 396, 24-32. doi:10.1016/j.jhydrol.2010.10.028 Logsdon, S.D., Jaynes, D.B., 1996. Spatial Variability of Hydraulic Conductivity in a Cultivated Field at Different Times. Soil Science Society of America Journal 60, 703. doi:10.2136/sssaj1996.03615995006000030003x Prieksat, M.A., Kaspar, T.C., Ankeny, M.D., 1994. Positional and Temporal Changes in Ponded Infiltration in a Corn Field. Soil Science Society of America Journal 58, 181. doi:10.2136/sssaj1994.03615995005800010026x Tricker, A.S., 1979. The design of a portable rainfall simulator infiltrometer. Journal of Hydrology 41, 143-147. doi:10.1016/0022-1694(79)90111-2 van De Giesen, N.C., Stomph, T.J., de Ridder, N., 2000. Scale effects of Hortonian overland flow and rainfall-runoff dynamics in a West African catena landscape. Hydrol. Process. 14, 165-175. doi:10.1002/(SICI)1099-1085(200001)14:1<165::AID-HYP920>3.0.CO;2-1 Zimmermann, A., Schinn, D.S., Francke, T., Elsenbeer, H., Zimmermann, B., 2013. Uncovering patterns of near-surface saturated hydraulic conductivity in an overland flow-controlled landscape. Geoderma 195-196, 1-11. doi:10.1016/j.geoderma.2012.11.002

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... shaking tables. (7) “Infiltration water” means that water which permeates through the earth into the plant... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., hydrocyclones, or shaking tables. (7) “Infiltration water” means that water which permeates through the earth... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

40 CFR 440.141 - Specialized definitions and provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... shaking tables. (7) “Infiltration water” means that water which permeates through the earth into the plant... drainage, and infiltration and drainage waters which commingle with mine drainage or waters resulting from... increase in volume from precipitation or infiltration, plus the maximum volume of water runoff resulting...

Transport behavior of surrogate biological warfare agents in a simulated landfill: effect of leachate recirculation and water infiltration.

PubMed

Saikaly, Pascal E; Hicks, Kristin; Barlaz, Morton A; de Los Reyes, Francis L

2010-11-15

An understanding of the transport behavior of biological warfare (BW) agents in landfills is required to evaluate the suitability of landfills for the disposal of building decontamination residue (BDR) following a bioterrorist attack on a building. Surrogate BW agents, Bacillus atrophaeus spores and Serratia marcescens, were spiked into simulated landfill reactors that were filled with synthetic building debris (SBD) and operated for 4 months with leachate recirculation or water infiltration. Quantitative polymerase chain reaction (Q-PCR) was used to monitor surrogate transport. In the leachate recirculation reactors, <10% of spiked surrogates were eluted in leachate over 4 months. In contrast, 45% and 31% of spiked S. marcescens and B. atrophaeus spores were eluted in leachate in the water infiltration reactors. At the termination of the experiment, the number of retained cells and spores in SBD was measured over the depth of the reactor. Less than 3% of the total spiked S. marcescens cells and no B. atrophaeus spores were detected in SBD. These results suggest that significant fractions of the spiked surrogates were strongly attached to SBD.

Characterizing Hydrological Processes in Vadose Zone by Direct Infiltration Water Sampling.

NASA Astrophysics Data System (ADS)

Mori, Y.; Higashi, N.; Somura, H.; Takeda, I.; Inoue, M.

2007-12-01

These days, planted forest mountainside was roughly maintained due to the population descent and small birth rate. Because thinning operation would delayed, forest was always dark and floor weed was rare. Management induced non point source pollution like surface soil erosion was suspected, however, we could not approach to the source with the stream water analysis. Therefore, direct soil water sampling device using glass fiber capillary force was developed to examine hydrological processes in watershed. In our design, water was collected just by the capillary force and let the excess water down through so that infiltration water was truly sampled and solute concentration kept the same quality as in soil water. The experiment was conducted at two neighboring Japanese cedar planted forest under different management, i.e., south slope was roughly maintained and west slope was well maintained by thinning operation. Load discharges were higher in south slope and lower in west slope. Infiltration water analysis revealed that ion concentration was gradually decreased at west slope, however in south slope, it dropped to lower level in soil water and increased again in stream water. The trend showed that soil buffering function was poor in south slope. Actually, disk permeameter survey revealed that hydraulic conductivity was small in south slope; TOC and biological activity were lower. This entire soil environment explained the water environmental differences in stream water. Because changes in soil environment affects water environment in the future, monitoring or examination of soil environment was considered as preventive measure for environmentally sound water and solute circulation in watershed.

Trench infiltration for managed aquifer recharge to permeable bedrock

USGS Publications Warehouse

Heilweil, V.M.; Watt, D.E.

2011-01-01

Managed aquifer recharge to permeable bedrock is increasingly being utilized to enhance resources and maintain sustainable groundwater development practices. One such target is the Navajo Sandstone, an extensive regional aquifer located throughout the Colorado Plateau of the western United States. Spreading-basin and bank-filtration projects along the sandstone outcrop's western edge in southwestern Utah have recently been implemented to meet growth-related water demands. This paper reports on a new cost-effective surface-infiltration technique utilizing trenches for enhancing managed aquifer recharge to permeable bedrock. A 48-day infiltration trench experiment on outcropping Navajo Sandstone was conducted to evaluate this alternative surface-spreading artificial recharge method. Final infiltration rates through the bottom of the trench were about 0.5 m/day. These infiltration rates were an order of magnitude higher than rates from a previous surface-spreading experiment at the same site. The higher rates were likely caused by a combination of factors including the removal of lower permeability soil and surficial caliche deposits, access to open vertical sandstone fractures, a reduction in physical clogging associated with silt and biofilm layers, minimizing viscosity effects by maintaining isothermal conditions, minimizing chemical clogging caused by carbonate mineral precipitation associated with algal photosynthesis, and diminished gas clogging associated with trapped air and biogenic gases. This pilot study illustrates the viability of trench infiltration for enhancing surface spreading of managed aquifer recharge to permeable bedrock. ?? 2010.

Unstable infiltration fronts in porous media on laboratory scale

NASA Astrophysics Data System (ADS)

Schuetz, Cindi; Neuweiler, Insa

2014-05-01

Water flow and transport of substances in the unsaturated zone are important processes for the quality and quantity of water in the hydrologic cycle. The water movement through preferential paths is often much faster than standard models (e. g. Richards equation in homogeneous porous media) predict. One type/phenomenon of preferential flow can occur during water infiltration into coarse and/or dry porous media: the so-called gravity-driven fingering flow. To upscale the water content and to describe the averaged water fluxes in order to couple models of different spheres it is necessary to understand and to quantify the behavior of flow instabilities. We present different experiments of unstable infiltration in homogeneous and heterogeneous structures to analyze development and morphology of gravity-driven fingering flow on the laboratory scale. Experiments were carried out in two-dimensional and three-dimensional sand tanks as well as in larger two-dimensional sand tanks with homogeneous and heterogeneous filling of sand and glass beads. In the small systems, water content in the medium was measured at different times. We compare the experiments to prediction of theoretical approaches (e.g. Saffman and Taylor, 1958; Chuoke et al., 1959; Philip 1975a; White et al., 1976; Parlange and Hill, 1976a; Glass et al., 1989a; Glass et al., 1991; Wang et al., 1998c) that quantify properties of the gravity-driven fingers. We use hydraulic parameters needed for the theoretical predictions (the water-entry value (hwe), van Genuchten parameter (Wang et al., 1997, Wang et al., 2000) and saturated conductivity (Ks), van Genuchten parameter (Guarracino, 2007) to simplify the prediction of the finger properties and if necessary to identify a constant correction factor. We find in general that the finger properties correspond well to theoretical predictions. In heterogeneous settings, where fine inclusions are embedded into a coarse material, the finger properties do not change much, while the inclusions act as a storage that is filled during the infiltration process. References: Chouke, R.L., van Meurs, P., and van der Poel, C., 1959. The instability of slow immiscible, viscous liquid-liquid displacements in permeable media, Trans. AIME. 216:188-194. Glass, R.J., Steenhuis, T.S., and Parlange J.-Y., 1989a. Mechanism for finger persistence in homogeneous, unsaturated, porous media: Theory and verification, Soil Sci. 148:60-70. Glass R.J., Parlange, J.-Y., and Steenhuis, T.S., 1991. Immiscible displacement in porous media: Stability analysis of three-dimensional, axisymmetric disturbances with application to gravity-driven wetting front instability, Water Resour. Res., 27, 1947-1956. Guarracino, L., 2007. Estimation of saturated hydraulic conductivity Ks from the van Genuchten shape parameter , Water Resour. Res., 43, W11502. Parlange, J.-Y. and Hill, D.E., 1976a. Theoretical analysis of wetting front instability in soils, Soil Sci. 122:236-239. Philip, J. 1975a. Stability analysis of infiltration, Soil Sci. Soc. Am. Proc. 39:1042-1049. Saffman, P.G. and Taylor, G., 1958. The penetration of a fluid into a porous medium or hele-shaw cell containing a more viscous liquid, Proc. R. Soc. London, 245:312-329. Wang Z., Feyen, J., Nielsen, D.R., and van Genuchten, M.T., 1997. Two-phase flow infiltration equations accounting for air entrapment effects, Water Resour. Res., 33:2759-2767. Wang, Z., Feyen, J., and Elrick, D.E., 1998c. Prediction of fingering in porous media, Water Resour. Res. 34(9):2183-2190. Wang Z., Wu, L., and Wu, Q.J., 2000. Water-entry value as an alternative indicator of soil water-repellency and wettability, Journal of Hydrology., 231-232, 76-83. White, I., Colombera, P.M., and Philip, J.R., 1976. Experimental studies of wetting front instability induced by sudden changes of pressure gradient, Soil Sci. Soc. Am. Proc., 40:824-829.

Measurement of Sedimentary Interbed Hydraulic Properties and Their Hydrologic Influence near the Idaho Nuclear Technology and Engineering Center at the Idaho National Engineering and Environmental Laboratory

USGS Publications Warehouse

Perkins, Kim S.

2003-01-01

Disposal of wastewater to unlined infiltration ponds near the Idaho Nuclear Technology and Engineering Center (INTEC), formerly known as the Idaho Chemical Processing Plant, at the Idaho National Engineering and Environmental Laboratory (INEEL) has resulted in the formation of perched water bodies in the unsaturated zone (Cecil and others, 1991). The unsaturated zone at INEEL comprises numerous basalt flows interbedded with thinner layers of coarse- to fine-grained sediments and perched ground-water zones exist at various depths associated with massive basalts, basalt-flow contacts, sedimentary interbeds, and sediment-basalt contacts. Perched ground water is believed to result from large infiltration events such as seasonal flow in the Big Lost River and wastewater discharge to infiltration ponds. Evidence from a large-scale tracer experiment conducted in 1999 near the Radioactive Waste Management Complex (RWMC), approximately 13 km from the INTEC, indicates that rapid lateral flow of perched water in the unsaturated zone may be an important factor in contaminant transport at the INEEL (Nimmo and others, 2002b). Because sedimentary interbeds, and possibly baked-zone alterations at sediment-basalt contacts (Cecil and other, 1991) play an important role in the generation of perched water it is important to assess the hydraulic properties of these units.

Biochar impact on water infiltration and water quality through a compacted subsoil layer

EPA Science Inventory

Soils in the SE USA Coastal Plain region frequently have a compacted subsoil layer (E horizon), which is a barrier for water infiltration. Four different biochars were evaluated to increase water infiltration through a compacted horizon from a Norfolk soil (fine-loamy, kaolinitic...

Estimating the spatial distribution of artificial groundwater recharge using multiple tracers.

PubMed

Moeck, Christian; Radny, Dirk; Auckenthaler, Adrian; Berg, Michael; Hollender, Juliane; Schirmer, Mario

2017-10-01

Stable isotopes of water, organic micropollutants and hydrochemistry data are powerful tools for identifying different water types in areas where knowledge of the spatial distribution of different groundwater is critical for water resource management. An important question is how the assessments change if only one or a subset of these tracers is used. In this study, we estimate spatial artificial infiltration along an infiltration system with stage-discharge relationships and classify different water types based on the mentioned hydrochemistry data for a drinking water production area in Switzerland. Managed aquifer recharge via surface water that feeds into the aquifer creates a hydraulic barrier between contaminated groundwater and drinking water wells. We systematically compare the information from the aforementioned tracers and illustrate differences in distribution and mixing ratios. Despite uncertainties in the mixing ratios, we found that the overall spatial distribution of artificial infiltration is very similar for all the tracers. The highest infiltration occurred in the eastern part of the infiltration system, whereas infiltration in the western part was the lowest. More balanced infiltration within the infiltration system could cause the elevated groundwater mound to be distributed more evenly, preventing the natural inflow of contaminated groundwater. Dedicated to Professor Peter Fritz on the occasion of his 80th birthday.

The effect of trees on preferential flow and soil infiltrability in an agroforestry parkland in semiarid Burkina Faso.

PubMed

Bargués Tobella, A; Reese, H; Almaw, A; Bayala, J; Malmer, A; Laudon, H; Ilstedt, U

2014-04-01

Water scarcity constrains the livelihoods of millions of people in tropical drylands. Tree planting in these environments is generally discouraged due to the large water consumption by trees, but this view may neglect their potential positive impacts on water availability. The effect of trees on soil hydraulic properties linked to groundwater recharge is poorly understood. In this study, we performed 18 rainfall simulations and tracer experiments in an agroforestry parkland in Burkina Faso to investigate the effect of trees and associated termite mounds on soil infiltrability and preferential flow. The sampling points were distributed in transects each consisting of three positions: (i) under a single tree, (ii) in the middle of an open area, and (iii) under a tree associated with a termite mound. The degree of preferential flow was quantified through parameters based on the dye infiltration patterns, which were analyzed using image analysis of photographs. Our results show that the degree of preferential flow was highest under trees associated with termite mounds, intermediate under single trees, and minimal in the open areas. Tree density also had an influence on the degree of preferential flow, with small open areas having more preferential flow than large ones. Soil infiltrability was higher under single trees than in the open areas or under trees associated with a termite mound. The findings from this study demonstrate that trees have a positive impact on soil hydraulic properties influencing groundwater recharge, and thus such effects must be considered when evaluating the impact of trees on water resources in drylands. Trees in dryland landscapes increase soil infiltrability and preferential flow Termite mounds in association with trees further enhance preferential flow.

The effect of trees on preferential flow and soil infiltrability in an agroforestry parkland in semiarid Burkina Faso

PubMed Central

Bargués Tobella, A; Reese, H; Almaw, A; Bayala, J; Malmer, A; Laudon, H; Ilstedt, U

2014-01-01

Water scarcity constrains the livelihoods of millions of people in tropical drylands. Tree planting in these environments is generally discouraged due to the large water consumption by trees, but this view may neglect their potential positive impacts on water availability. The effect of trees on soil hydraulic properties linked to groundwater recharge is poorly understood. In this study, we performed 18 rainfall simulations and tracer experiments in an agroforestry parkland in Burkina Faso to investigate the effect of trees and associated termite mounds on soil infiltrability and preferential flow. The sampling points were distributed in transects each consisting of three positions: (i) under a single tree, (ii) in the middle of an open area, and (iii) under a tree associated with a termite mound. The degree of preferential flow was quantified through parameters based on the dye infiltration patterns, which were analyzed using image analysis of photographs. Our results show that the degree of preferential flow was highest under trees associated with termite mounds, intermediate under single trees, and minimal in the open areas. Tree density also had an influence on the degree of preferential flow, with small open areas having more preferential flow than large ones. Soil infiltrability was higher under single trees than in the open areas or under trees associated with a termite mound. The findings from this study demonstrate that trees have a positive impact on soil hydraulic properties influencing groundwater recharge, and thus such effects must be considered when evaluating the impact of trees on water resources in drylands. Key Points Trees in dryland landscapes increase soil infiltrability and preferential flow Termite mounds in association with trees further enhance preferential flow PMID:25641996

Rain Gardens: Stormwater Infiltrating Systems

EPA Science Inventory

The hydrological dynamics and changes in stormwater nutrient concentrations within rain gardens were studied by introducing captured stormwater runoff to rain gardens at EPA’s Urban Water Research Facility in Edison, New Jersey. The runoff used in these experiments was collected...

Hydrologic behavior of two engineered barriers following extreme wetting.

PubMed

Porro, I

2001-01-01

Many engineered barriers are expected to function for hundreds of years or longer. Over the course of time, it is likely that some barriers will experience infiltration to the point of breakthrough. This study compares the recovery from breakthrough of two storage-evapotranspiration type engineered barriers. Replicates of test plots comprising thick soil and capillary-biobarrier covers were wetted to breakthrough in 1997. Test plots were kept cleared of vegetation to maximize hydrologic stress during recovery. Following cessation of drainage resulting from the wetting irrigations, water storage levels in all plots were at elevated levels compared with pre-irrigation levels. As a result, infiltration of melting snow during the subsequent spring overloaded the storage capacity and produced drainage in all plots. Relatively rapid melting of accumulated snowfall produced the most significant infiltration events each year during the study. Capillary barriers yielded less total drainage than thick soil barriers. By limiting drainage, capillary barriers increased water storage in the upper portions of the test plots, which led to increased evaporation from the capillary barrier plots compared with thick soil plots. Increased evaporation in the capillary barrier plots allowed more water to infiltrate in the second season following the wetting tests without triggering drainage. All thick soil plots again yielded drainage in the second season. Within two years of intentionally induced breakthrough, evaporation alone (without transpiration) restored the capability of the capillary barrier covers to function as intended, although water storage in these covers remained at elevated levels.

Effects of sodium polyacrylate on water retention and infiltration capacity of a sandy soil.

PubMed

Zhuang, Wenhua; Li, Longguo; Liu, Chao

2013-01-01

Based on the laboratory study, the effects of sodium polyacrylate (SP) was investigated at 5 rates of 0, 0.08, 0.2, 0.5, and 1%, on water retention, saturated hydraulic conductivity(Ks), infiltration characteristic and water distribution profiles of a sandy soil. The results showed that water retention and available water capacity effectively increased with increasing SP rate. The Ks and the rate of wetting front advance and infiltration under certain pond infiltration was significantly reduced by increasing SP rate, which effectively reduced water in a sandy soil leaking to a deeper layer under the plough layer. The effect of SP on water distribution was obviously to the up layer and very little to the following deeper layers. Considering both the effects on water retention and infiltration capacity, it is suggested that SP be used to the sandy soil at concentrations ranging from 0.2 to 0.5%.

Study of penetration behavior of PCB-DNAPL in a sand layer by a column experiment.

PubMed

Okuda, Nobuyasu; Shimizu, Takaaki; Muratani, Masaru; Terada, Akihiko; Hosomi, Masaaki

2014-11-01

To better understand the infiltration performances of high concentration PCB oils (KC-300 and KC-1000 polychlorinated biphenyl (PCB) mixtures), representative dense non-aqueous phase liquid (DNAPL), under both saturated and unsaturated conditions, we conducted experiments on a sand column filled with Toyoura Standard Sand. When PCB oil with the volume comparable to the total porosity in the column was supplied, the residual PCB concentrations under PCB-water conditions were 4.9×10(4)mgkg(-1) in KC-300 and 3.9×10(4)mgkg(-1) in KC-1000. Under PCB-air conditions, residual PCB concentrations were 6.0×10(4)mgkg(-1) and 2.4×10(5)mgkg(-1) in the upper and lower parts for KC-300 and 3.6×10(4)mgkg(-1) and 1.5×10(5)mgkg(-1) in those for KC-1000, respectively, while the rest of the PCBs were infiltrated. On the other hand, when a small amount of PCB oil with the volume far smaller than the total porosity in the column was supplied, the original PCBs were not transported via water permeation. However, lower-chlorinated PCB congeners-e.g., di- or tri-chlorinated biphenyls-preferentially dissolved and were infiltrated from the bottom of the column. These propensities on PCB oil infiltration can be explained in conjunction with the degree of PCB saturation in the sand column. Copyright © 2014 Elsevier Ltd. All rights reserved.

NMR 1D-imaging of water infiltration into mesoporous matrices.

PubMed

Le Feunteun, Steven; Diat, Olivier; Guillermo, Armel; Poulesquen, Arnaud; Podor, Renaud

2011-04-01

It is shown that coupling nuclear magnetic resonance (NMR) 1D-imaging with the measure of NMR relaxation times and self-diffusion coefficients can be a very powerful approach to investigate fluid infiltration into porous media. Such an experimental design was used to study the very slow seeping of pure water into hydrophobic materials. We consider here three model samples of nuclear waste conditioning matrices which consist in a dispersion of NaNO(3) (highly soluble) and/or BaSO(4) (poorly soluble) salt grains embedded in a bitumen matrix. Beyond studying the moisture progression according to the sample depth, we analyze the water NMR relaxation times and self-diffusion coefficients along its 1D-concentration profile to obtain spatially resolved information on the solution properties and on the porous structure at different scales. It is also shown that, when the relaxation or self-diffusion properties are multimodal, the 1D-profile of each water population is recovered. Three main levels of information were disclosed along the depth-profiles. They concern (i) the water uptake kinetics, (ii) the salinity and the molecular dynamics of the infiltrated solutions and (iii) the microstructure of the water-filled porosities: open networks coexisting with closed pores. All these findings were fully validated and enriched by NMR cryoporometry experiments and by performing environmental scanning electronic microscopy observations. Surprisingly, results clearly show that insoluble salts enhance the water progression and thereby increase the capability of the material to uptake water. Copyright © 2011 Elsevier Inc. All rights reserved.

Quantifying the effects of wildfire on changes in soil properties by surface burning of soils from the Boulder Creek Critical Zone Observatory

USGS Publications Warehouse

Wieting, Celeste; Ebel, Brian A.; Singha, Kamini

2017-01-01

Study regionThis study used intact soil cores collected at the Boulder Creek Critical Zone Observatory near Boulder, Colorado, USA to explore fire impacts on soil properties.Study focusThree soil scenarios were considered: unburned control soils, and low- and high-temperature burned soils. We explored simulated fire impacts on field-saturated hydraulic conductivity, dry bulk density, total organic carbon, and infiltration processes during rainfall simulations.New hydrological insights for the regionSoils burned to high temperatures became more homogeneous with depth with respect to total organic carbon and bulk density, suggesting reductions in near-surface porosity. Organic matter decreased significantly with increasing soil temperature. Tension infiltration experiments suggested a decrease in infiltration rates from unburned to low-temperature burned soils, and an increase in infiltration rates in high-temperature burned soils. Non-parametric statistical tests showed that field-saturated hydraulic conductivity similarly decreased from unburned to low-temperature burned soils, and then increased with high-temperature burned soils. We interpret these changes result from the combustion of surface and near-surface organic materials, enabling water to infiltrate directly into soil instead of being stored in the litter and duff layer at the surface. Together, these results indicate that fire-induced changes in soil properties from low temperatures were not as drastic as high temperatures, but that reductions in surface soil water repellency in high temperatures may increase infiltration relative to low temperatures.

Characteristics of water infiltration in layered water repellent soils

USDA-ARS?s Scientific Manuscript database

Hydrophobic soil can influence soil water infiltration, but information regarding the impacts of different levels of hydrophobicity within a layered soil profile is limited. An infiltration study was conducted to determine the effects of different levels of hydrophobicity and the position of the hyd...

Quantification of sewer system infiltration using delta(18)O hydrograph separation.

PubMed

Prigiobbe, V; Giulianelli, M

2009-01-01

The infiltration of parasitical water into two sewer systems in Rome (Italy) was quantified during a dry weather period. Infiltration was estimated using the hydrograph separation method with two water components and delta(18)O as a conservative tracer. The two water components were groundwater, the possible source of parasitical water within the sewer, and drinking water discharged into the sewer system. This method was applied at an urban catchment scale in order to test the effective water-tightness of two different sewer networks. The sampling strategy was based on an uncertainty analysis and the errors have been propagated using Monte Carlo random sampling. Our field applications showed that the method can be applied easily and quickly, but the error in the estimated infiltration rate can be up to 20%. The estimated infiltration into the recent sewer in Torraccia is 14% and can be considered negligible given the precision of the method, while the old sewer in Infernetto has an estimated infiltration of 50%.

Removal of organic micropollutants in an artificial recharge system

NASA Astrophysics Data System (ADS)

Valhondo, C.; Nödler, K.; Köck-Schulmeyer, M.; Hernandez, M.; Licha, T.; Ayora, C.; Carrera, J.

2012-04-01

Emerging contaminants including pharmaceutically active compounds (PhACs), personal care products (PCPs) and pesticides are increasingly being identified in the environment. Emerging pollutants and their transformation products show low concentration in the environment (ng/L), but the effects of the mixtures and lifelong exposure to humans are currently unknown. Many of these contaminants are removed under aerobic conditions in water treatment plants. However, several pharmaceuticals and metabolites present in wastewater are not eliminated by conventional treatment processes. Several lab studies, however, show that the behaviour of many of these micropollutants is affected by the dominant redox conditions. However, data from field experiments are limited and sometimes contradictory. Artificial recharge is a widespread technology to increase the groundwater resources. In this study we propose a design to enhance the natural remediation potential of the aquifer with the installation of a reactive layer at the bottom of the infiltration pond. This layer is a mixture of compost, aquifer material, clay and iron oxide. This layer is intended to provide an extra amount of DOC to the recharge water and to promote biodegradation by means of the development of different redox zones along the travel path through the unsaturated zone and within the aquifer. Moreover, compost, clay and iron oxide of the layer are assumed to increase sorption surfaces for neutral, cationic and anionic compounds, respectively. The infiltration system is sited in Sant Vicenç dels Horts (Barcelona, Spain). It consists of a decantation pond, receiving raw water from the Llobregat River (highly affected from treatment plant effluents), and an infiltration pond (5600 m2). The infiltration rate is around 1 m3/m2/day. The system is equipped with a network of piezometers, suction cups and tensiometers. Infiltration periods have been performed before and after the installation of the reactive layer. Water from the Infiltration pond, the unsaturated zone and groundwater have been sampled and analyzed in order to elucidate the effect of the reactive layer. First results of micropollutants under natural conditions show significant removal rates of atenolol and Ibuprofen as well as the recalcitrant behaviour of carbamazepine. Once the layer was installed, carbamazepine concentration in groundwater samples was lower than the concentration in the infiltration water. These preliminary results are promising but, however, they need to be confirmed by further analysis, which will be conducted during the next weeks.

Smart Fluids in Hydrology: Use of Non-Newtonian Fluids for Pore Structure Characterization

NASA Astrophysics Data System (ADS)

Abou Najm, M. R.; Atallah, N. M.; Selker, J. S.; Roques, C.; Stewart, R. D.; Rupp, D. E.; Saad, G.; El-Fadel, M.

2015-12-01

Classic porous media characterization relies on typical infiltration experiments with Newtonian fluids (i.e., water) to estimate hydraulic conductivity. However, such experiments are generally not able to discern important characteristics such as pore size distribution or pore structure. We show that introducing non-Newtonian fluids provides additional unique flow signatures that can be used for improved pore structure characterization while still representing the functional hydraulic behavior of real porous media. We present a new method for experimentally estimating the pore structure of porous media using a combination of Newtonian and non-Newtonian fluids. The proposed method transforms results of N infiltration experiments using water and N-1 non-Newtonian solutions into a system of equations that yields N representative radii (Ri) and their corresponding percent contribution to flow (wi). This method allows for estimating the soil retention curve using only saturated experiments. Experimental and numerical validation comparing the functional flow behavior of different soils to their modeled flow with N representative radii revealed the ability of the proposed method to represent the water retention and infiltration behavior of real soils. The experimental results showed the ability of such fluids to outsmart Newtonian fluids and infer pore size distribution and unsaturated behavior using simple saturated experiments. Specifically, we demonstrate using synthetic porous media that the use of different non-Newtonian fluids enables the definition of the radii and corresponding percent contribution to flow of multiple representative pores, thus improving the ability of pore-scale models to mimic the functional behavior of real porous media in terms of flow and porosity. The results advance the knowledge towards conceptualizing the complexity of porous media and can potentially impact applications in fields like irrigation efficiencies, vadose zone hydrology, soil-root-plant continuum, carbon sequestration into geologic formations, soil remediation, petroleum reservoir engineering, oil exploration and groundwater modeling.

Infiltration of late Palaeozoic evaporative brines in the reelfoot rift: A possible salt source for Illinois Basin formation waters and MVT mineralizing fluids

USGS Publications Warehouse

Rowan, E.L.; De Marsily, G.

2001-01-01

Salinities and homogenization temperatures of fluid inclusions in Mississippi Valley-type (MVT) deposits provide important insights into the regional hydrology of the Illinois basin/Reelfoot rift system in late Palaeozoic time. Although the thermal regime of this basin system has been plausibly explained, the origin of high salinities in the basin fluids remains enigmatic. Topographically driven flow appears to have been essential in forming these MVT districts, as well as many other districts worldwide. However, this type of flow is recharged by fresh water making it difficult to account for the high salinities of the mineralizing fluids over extended time periods. Results of numerical experiments carried out in this study provide a possible solution to the salinity problem presented by the MVT zinc-lead and fluorite districts at the margins of the basin system. Evaporative concentration of surface water and subsequent infiltration into the subsurface are proposed to account for large volumes of brine that are ultimately responsible for mineralization of these districts. This study demonstrates that under a range of geologically reasonable conditions, brine infiltration into an aquifer in the deep subsurface can coexist with topographically driven flow. Infiltration combined with regional flow and local magmatic heat sources in the Reelfoot rift explain the brine concentrations as well as the temperatures observed in the Southern Illinois and Upper Mississippi Valley districts.

A MODFLOW Infiltration Device Package for Simulating Storm Water Infiltration.

PubMed

Jeppesen, Jan; Christensen, Steen

2015-01-01

This article describes a MODFLOW Infiltration Device (INFD) Package that can simulate infiltration devices and their two-way interaction with groundwater. The INFD Package relies on a water balance including inflow of storm water, leakage-like seepage through the device faces, overflow, and change in storage. The water balance for the device can be simulated in multiple INFD time steps within a single MODFLOW time step, and infiltration from the device can be routed through the unsaturated zone to the groundwater table. A benchmark test shows that the INFD Package's analytical solution for stage computes exact results for transient behavior. To achieve similar accuracy by the numerical solution of the MODFLOW Surface-Water Routing (SWR1) Process requires many small time steps. Furthermore, the INFD Package includes an improved representation of flow through the INFD sides that results in lower infiltration rates than simulated by SWR1. The INFD Package is also demonstrated in a transient simulation of a hypothetical catchment where two devices interact differently with groundwater. This simulation demonstrates that device and groundwater interaction depends on the thickness of the unsaturated zone because a shallow groundwater table (a likely result from storm water infiltration itself) may occupy retention volume, whereas a thick unsaturated zone may cause a phase shift and a change of amplitude in groundwater table response to a change of infiltration. We thus find that the INFD Package accommodates the simulation of infiltration devices and groundwater in an integrated manner on small as well as large spatial and temporal scales. © 2014, National Ground Water Association.

A field method for measurement of infiltration

USGS Publications Warehouse

Johnson, A.I.

1963-01-01

The determination of infiltration--the downward entry of water into a soil (or sediment)--is receiving increasing attention in hydrologic studies because of the need for more quantitative data on all phases of the hydrologic cycle. A measure of infiltration, the infiltration rate, is usually determined in the field by flooding basins or furrows, sprinkling, or measuring water entry from cylinders (infiltrometer rings). Rates determined by ponding in large areas are considered most reliable, but the high cost usually dictates that infiltrometer rings, preferably 2 feet in diameter or larger, be used. The hydrology of subsurface materials is critical in the study of infiltration. The zone controlling the rate of infiltration is usually the least permeable zone. Many other factors affect infiltration rate--the sediment (soil) structure, the condition of the sediment surface, the distribution of soil moisture or soil- moisture tension, the chemical and physical nature of the sediments, the head of applied water, the depth to ground water, the chemical quality and the turbidity of the applied water, the temperature of the water and the sediments, the percentage of entrapped air in the sediments, the atmospheric pressure, the length of time of application of water, the biological activity in the sediments, and the type of equipment or method used. It is concluded that specific values of the infiltration rate for a particular type of sediment are probably nonexistent and that measured rates are primarily for comparative use. A standard field-test method for determining infiltration rates by means of single- or double-ring infiltrometers is described and the construction, installation, and operation of the infiltrometers are discussed in detail.

Mechanisms of water infiltration into conical hydrophobic nanopores.

PubMed

Liu, Ling; Zhao, Jianbing; Yin, Chun-Yang; Culligan, Patricia J; Chen, Xi

2009-08-14

Fluid channels with inclined solid walls (e.g. cone- and slit-shaped pores) have wide and promising applications in micro- and nano-engineering and science. In this paper, we use molecular dynamics (MD) simulations to investigate the mechanisms of water infiltration (adsorption) into cone-shaped nanopores made of a hydrophobic graphene sheet. When the apex angle is relatively small, an external pressure is required to initiate infiltration and the pressure should keep increasing in order to further advance the water front inside the nanopore. By enlarging the apex angle, the pressure required for sustaining infiltration can be effectively lowered. When the apex angle is sufficiently large, under ambient condition water can spontaneously infiltrate to a certain depth of the nanopore, after which an external pressure is still required to infiltrate more water molecules. The unusual involvement of both spontaneous and pressure-assisted infiltration mechanisms in the case of blunt nanocones, as well as other unique nanofluid characteristics, is explained by the Young's relation enriched with the size effects of surface tension and contact angle in the nanoscale confinement.

The use of One-Dimensional Laboratory Experiments to Assess Hydraulic Processes in Wastewater Soil Absorption Systems

NASA Astrophysics Data System (ADS)

Huntzinger, D. N.; McCray, J. E.; Siegrist, R.; Lowe, K.; VanCuyk, S.

2001-05-01

Sixteen, one-dimensional column lysimeters have been developed to evaluate the influence of loading regime and infiltrative surface character on hydraulic performance in wastewater soil absorption systems. A duplicate design was utilized to evaluate two infiltrative surface conditions (gravel-free vs. gravel-laden) under four hydraulic loading regimes representative of possible field conditions. By loading the columns at rates of 25 to 200 cm/day, the 17 weeks of column operation actually reflect up to approximately 13 yrs of field operation (at 5 cm/day). Therefore, the cumulative mass throughput and infiltrative rate loss for each loading regime can be examined to determine the viability of accelerated loading as a means to compress the time scale of observation, while still producing meaningfully results for the field scale. During operation, the columns were loaded with septic tank effluent at a prescribed rate and routinely monitoring for applied effluent composition, infiltration rate, time-dependant soil water content, water volume throughput, and percolate composition. Bromide tracer tests were completed prior to system startup and at weeks 2, 6, and 17 of system operation. Hydraulic characterization of the columns is based on measurements of the hydraulic loading rate, volumetric throughput, soil water content, and bromide breakthrough curves. Incipient ponding of wastewater developed during the 1st week of operation for columns loaded at the highest hydraulic rate (loading regimes 1 and 2), and during the 3rd and 6th week of operation for loading regimes 3 and 4, respectfully. The bromide breakthrough curves exhibit later breakthrough and tailing as system life increases, indicating the development of spatially variability in hydraulic conductivity within the column and the development of a clogging zone at the infiltrative surface. Throughput is assessed for each loading regime to determine the infiltration rate loss versus days of operation. Loading regimes 1 and 2 approach a comparable long-term throughput rate less than 20 cm/day, while loading regimes 3 and 4 reach a long-term throughput rate of less than 10 cm/day. These one-dimensional columns allow for the analysis of infiltrative rate loss and hydraulic behavior as a result of infiltrative surface character and loading regime.

Managed aquifer recharge of treated wastewater: water quality changes resulting from infiltration through the vadose zone.

PubMed

Bekele, Elise; Toze, Simon; Patterson, Bradley; Higginson, Simon

2011-11-01

Secondary treated wastewater was infiltrated through a 9 m-thick calcareous vadose zone during a 39 month managed aquifer recharge (MAR) field trial to determine potential improvements in the recycled water quality. The water quality improvements of the recycled water were based on changes in the chemistry and microbiology of (i) the recycled water prior to infiltration relative to (ii) groundwater immediately down-gradient from the infiltration gallery. Changes in the average concentrations of several constituents in the recycled water were identified with reductions of 30% for phosphorous, 66% for fluoride, 62% for iron and 51% for total organic carbon when the secondary treated wastewater was infiltrated at an applied rate of 17.5 L per minute with a residence time of approximately four days in the vadose zone and less than two days in the aquifer. Reductions were also noted for oxazepam and temazepam among the pharmaceuticals tested and for a range of microbial pathogens, but reductions were harder to quantify as their magnitudes varied over time. Total nitrogen and carbamazepine persisted in groundwater down-gradient from the infiltration galleries. Infiltration does potentially offer a range of water quality improvements over direct injection to the water table without passage through the unsaturated zone; however, additional treatment options for the non-potable water may still need to be considered, depending on the receiving environment or the end use of the recovered water. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

[Effects of soil crusts on surface hydrology in the semiarid Loess hilly area].

PubMed

Wei, Wei; Wen, Zhi; Chen, Li-Ding; Chen, Jin; Wu, Dong-Ping

2012-11-01

Soil crusts are distributed extensively in the Chinese Loess Plateau and play key roles in surface hydrological processes. In this study, a typical loess hilly region in Anjiagou catchment, Dingxi city, Gansu province was selected as the study region, and soil crusts in the catchment were investigated. Then, the hydrological effect of soil crusts was studied by using multi-sampling and hydrological monitoring experiments. Several key results were shown as follows. Firstly, compared with bared soil without crust cover, soil crusts can greatly reduce the bulk density, improve the porosity of soil, and raise the holding capacity of soil moisture which ranges from 1.4 to 1.9 times of that of bared soil. Secondly, the role of soil crust on rainfall interception was very significant. Moss crust was found to be strongest on rainfall interception, followed by synantectic crusts and lichen crusts. Bared soil without covering crusts was poorest in resisting rainfall splash. Thirdly, hydrological simulation experiments indicate that soil crusts play a certain positive role in promoting the water infiltration capacity, and the mean infiltration rate of the crusted soil was 2 times higher than that of the no-crust covered soils. While the accumulated infiltrated water amounts was also far higher than that of the bared soil.

Infiltration in unsaturated layered fluvial deposits at Rio Bravo : photo essay and data summary.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brainard, James Robert; Glass, Robert John, Jr.

2007-08-01

An infiltration and dye transport experiment was conducted to visualize flow and transport processes in a heterogeneous, layered, sandy-gravelly fluvial deposit adjacent to Rio Bravo Boulevard in Albuquerque, NM. Water containing red dye followed by blue-green dye was ponded in a small horizontal zone ({approx}0.5 m x 0.5 m) above a vertical outcrop ({approx}4 m x 2.5 m). The red dye lagged behind the wetting front due to slight adsorption thus allowing both the wetting front and dye fronts to be observed in time at the outcrop face. After infiltration, vertical slices were excavated to the midpoint of the infiltrometermore » exposing the wetting front and dye distribution in a quasi three-dimensional manner. At small-scale, wetting front advancement was influenced by the multitude of local capillary barriers within the deposit. However at the scale of the experiment, the wetting front appeared smooth with significant lateral spreading {approx} twice that in the vertical, indicating a strong anisotropy due to the pronounced horizontal layering. The dye fronts exhibited appreciably more irregularity than the wetting front, as well as the influence of preferential flow features (a fracture) that moved the dye directly to the front, bypassing the fresh water between.« less

Role of slope on infiltration: A review

NASA Astrophysics Data System (ADS)

Morbidelli, Renato; Saltalippi, Carla; Flammini, Alessia; Govindaraju, Rao S.

2018-02-01

Partitioning of rainfall at the soil-atmosphere interface is important for both surface and subsurface hydrology, and influences many events of major hydrologic interest such as runoff generation, aquifer recharge, and transport of pollutants in surface waters as well as the vadose zone. This partitioning is achieved through the process of infiltration that has been widely investigated at the local scale, and more recently also at the field scale, by models that were designed for horizontal surfaces. However, infiltration, overland flows, and deep flows in most real situations are generated by rainfall over sloping surfaces that bring in additional effects. Therefore, existing models for local infiltration into homogeneous and layered soils and those as for field-scale infiltration, have to be adapted to account for the effects of surface slope. Various studies have investigated the role of surface slope on infiltration based on a theoretical formulations for the dynamics of infiltration, extensions of the Green-Ampt approach, and from laboratory and field experiments. However, conflicting results have been reported in the scientific literature on the role of surface slope on infiltration. We summarize the salient points from previous studies and provide plausible reasons for discrepancies in conclusions of previous authors, thus leading to a critical assessment of the current state of our understanding on this subject. We offer suggestions for future efforts to advance our knowledge of infiltration over sloping surfaces.

Study of the water transportation characteristics of marsh saline soil in the Yellow River Delta.

PubMed

He, Fuhong; Pan, Yinghua; Tan, Lili; Zhang, Zhenhua; Li, Peng; Liu, Jia; Ji, Shuxin; Qin, Zhaohua; Shao, Hongbo; Song, Xueyan

2017-01-01

One-dimensional soil column water infiltration and capillary adsorption water tests were conducted in the laboratory to study the water transportation characteristics of marsh saline soil in the Yellow River Delta, providing a theoretical basis for the improvement, utilization and conservation of marsh saline soil. The results indicated the following: (1) For soils with different vegetation covers, the cumulative infiltration capacity increased with the depth of the soil layers. The initial infiltration rate of soils covered by Suaeda and Tamarix chinensis increased with depth of the soil layers, but that of bare soil decreased with soil depth. (2) The initial rate of capillary rise of soils with different vegetation covers showed an increasing trend from the surface toward the deeper layers, but this pattern with respect to soil depth was relatively weak. (3) The initial rates of capillary rise were lower than the initial infiltration rates, but infiltration rate decreased more rapidly than capillary water adsorption rate. (4) The two-parameter Kostiakov model can very well-simulate the changes in the infiltration and capillary rise rates of wetland saline soil. The model simulated the capillary rise rate better than it simulated the infiltration rate. (5) There were strong linear relationships between accumulative infiltration capacity, wetting front, accumulative capillary adsorbed water volume and capillary height. Copyright © 2016 Elsevier B.V. All rights reserved.

Water and solute transport parameterization form a soil of semi-arid region of northeast of Brazil

NASA Astrophysics Data System (ADS)

Netto, A. M.; Antonino, A. C. D.; Lima, L. J. S.; Angulo-Jaramillo, R.; Montenegro, S. M. G.

2003-04-01

Water and solute transfer modeling needs the transport parameters as input data. Classical theory, Fickian advection-dispersion, is not successfully applied to account for solute transport along with preferential flow pathways. This transport may be operating at scales smaller than spatial discretization used in a field scale numerical model. An axisymetric infiltration using a single ring infiltrometer along with a conservative tracer (Cl^-) is an efficient and easy method to use in fields tools. Two experiments were accomplished on a Yellow Oxissol in a 4,0 ha area in Centro de Ciências Agrárias, UFPB, Areia City, Paraíba State, Brazil (6^o 58'S, 35o 41'W and 645 m), in a 50 × 50 m grid (16 points): a) cultivated with beans (Vigna Unguinculata (L.) Walp.), and b) bare soil after harvest. The unsaturated hydraulic conductivity K and sorptivity S were estimated from short time or long time analysis of cumulative three dimensional infiltration. Single tracer technique was used for the calculation of mobile water fraction f by measuring the solute concentration underneath the ring infiltrometer, at the end of infiltration. A solute transfer numerical model, based on the mobile-immobile water concept, was used for the determination of the solute transport parameters. The mobile water fraction f, the dispersion coefficient D, and the mass transfer coefficient α, were estimated from both the measured infiltration depth and concentration profile underneath the ring infiltrometer. The presence of preferential flow was due to the soil nature (aggregated soil, macropores, flux instabilities and heterogeneity). The lateral solute transfer is not only diffusive but also convective. The parameters deduced from the numerical model associated to the solute profile concentration are representative of this phenomenon.

The removal of microorganisms and organic micropollutants from wastewater during infiltration to aquifers after irrigation of farmland in the Tula Valley, Mexico.

PubMed

Chávez, Alma; Maya, Catalina; Gibson, Richard; Jiménez, Blanca

2011-05-01

The Tula Valley receives untreated wastewater from Mexico City for agricultural irrigation, half of which infiltrates to aquifers from where drinking water is extracted. Samples of wastewater and infiltrated water from three areas of the valley were analyzed for microorganisms, organic micropollutants, and some basic parameters. Concentrations of microorganisms in the infiltrated water were generally very low but the incidence of fecal coliforms (present in 68% of samples), somatic bacteriophages (36%), Giardia spp. (14%), and helminth eggs (8%) suggested a health risk. Organic micropollutants, often present at high concentrations in the wastewater, were generally absent from the infiltrated water except carbamazepine which was in 55% of samples (up to 193 ng/L). There was no correlation between carbamazepine concentrations and the presence of microorganisms but highest concentrations of carbamazepine and boron coincided. A treatment such as nanofiltration would be necessary for the infiltrated water to be a safe potable supply. Copyright © 2011 Elsevier Ltd. All rights reserved.

Soil water infiltration affected by biofuel and grain crop production systems in claypan landscape

USDA-ARS?s Scientific Manuscript database

The effect of soil management systems on water infiltration is very crucial within claypan landscapes to maximize production as well as minimize environmental risks. The objective of this study was to assess the effect of topsoil thickness on water infiltration in claypan soils for grain and biofuel...

Electrical Resistance Imaging for Evaluation of Soil-Water Behavior in Desert Ecosystems

NASA Astrophysics Data System (ADS)

Nimmo, J. R.; Perkins, K. S.; Schmidt, K. M.; Miller, D. M.; Stock, J. D.; Singha, K.

2009-05-01

As part of an effort to evaluate habitat types in the Mojave National Preserve, we conducted infiltration/redistribution experiments to investigate unsaturated hydraulic properties and soil-water dynamics. Two investigated locations contrasted sharply in degree of pedogenic development: (1) recently deposited sediments in an active wash and (2) a highly developed soil of late Pleistocene age. Water flow through these materials may be strongly influenced by such features as biotic crusts, vesicular horizons, textural variations, calcic horizons, preferential flow paths, and other forms of vertical and lateral spatial variability. In each location we ponded water in a 1-m-diameter infiltration ring for 2.3 h, generating 1.93 m of infiltration in the active wash and 0.52 m in the Pleistocene soil. Combining input flux data with quantitative knowledge of water content and soil water pressure over space and time provides a basis for estimating soil hydraulic properties. TDR probes and tensiometers, placed outside but within a few m of the infiltration pond at depths to 1.5 m, provided subsurface hydraulic data. In addition to probe measurements, we conducted electrical resistance imaging (ERI) measurements during the infiltration period and for six days of redistribution. Electrodes were in two crossed lines at the surface, 24 in each, at 0.5 m spacing. On each line data were collected over an eight- minute period using a hybrid geometry, with 0 to 6 electrodes skipped between those used for the measurement. Relative change in the inverted resistivities relates to relative change in soil water content. Spatially exhaustive and minimally invasive characterization is valuable because of the extreme difficulty of quantifying soil-moisture distribution over a broad heterogeneous area using a set of individual probes. Soil moisture data directly under the ponded area are especially important, and ERI was our only means for such measurements because probe installation would have required either power drilling machinery (not permitted at this wilderness location), or the punching of holes in surficial layers whose flow-impeding effects are crucial to the system under investigation. ERI results show that the relatively coarse and homogeneous active wash sediments have minimal small-scale variation in water content and comparatively little ability to retain water over time. In the older soil, infiltrated water does not go nearly as deep, but spreads to a slightly greater lateral extent; both effects are consistent with the development of horizons that contrast sharply in texture, structure, or calcification. Water content in this developed soil shows pronounced spatial variability, especially in the direction across rather than down the alluvial fan. Certain small (<1 m3) parcels of the Pleistocene soil at depths less than 0.5 m have especially great ability to retain water. The juxtaposition of these with parcels of soil that strongly transmit but weakly retain water creates a net enhancing effect on the root-accessible soil's ability to hold water over extended time, as is vital in a climate of infrequent infiltration. Present ERI results indicate the basic spatial distribution of resistivity and its evolution over time. The rate of spreading of subsurface water, as well as the shape, character, and heterogeneity of its distribution, can be inferred from these, so the results already have substantial ecohydrologic value. Advances in ERI data inversion and water- content calibration would lead toward greatly enhanced value for quantifying unsaturated hydraulic properties and water fluxes.

Applying 2-D resistivity imaging and ground penetrating radar (GPR) methods to identify infiltration of water in the ground surface

NASA Astrophysics Data System (ADS)

Yusof, Azim Hilmy Mohamad; Azman, Muhamad Iqbal Mubarak Faharul; Ismail, Nur Azwin; Ismail, Noer El Hidayah

2017-07-01

Infiltration of water into the soil mostly happens in area near to the ocean or area where rain occurred frequently. This paper explains about the water infiltration process that occurred vertically and horizontally at the subsurface layer. Infiltration act as an indicator of the soil's ability to allow water movement into and through the soil profile. This research takes place at Teluk Kumbar, Pulau Pinang, area that located near to the sea. Thus, infiltration process occurs actively. The study area consists of unconsolidated marine clay, sand and gravel deposits. Furthermore, the methods used for this research is 2-D Resistivity Imaging by using Wenner-Schlumberger array with 2.5 m minimum electrode spacing, and the second method is Ground Penetrating Radar (GPR) with antenna frequency of 250MHz. 2-D Resistivity Imaging is used to investigate the subsurface layer of the soil. Other than that, this method can also be used to investigate the water infiltration that happens horizontally. GPR is used to investigate shallow subsurface layer and to investigate the water infiltration from above. The results of inversion model of 2-D Resistivity Imaging shows that the subsurface layer at distance of 0 m to 20 m are suspected to be salt water intrusion zone due to the resistivity value of 0 Ω.m to 1 Ω.m. As for the radargram results from the GPR, the anomaly seems to be blurry and unclear, and EM waves signal can only penetrate up to 1.5 m depth. This feature shows that the subsurface layer is saturated with salt water. Applying 2-D resistivity imaging and GPR method were implemented to each other in identifying infiltration of water in the ground surface.

New procedure for sampling infiltration to assess post-fire soil water repellency

Treesearch

P. R. Robichaud; S. A. Lewis; L. E. Ashmun

2008-01-01

The Mini-disk Infiltrometer has been adapted for use as a field test of post-fire infiltration and soil water repellency. Although the Water Drop Penetration Time (WDPT) test is the common field test for soil water repellency, the Mini-disk Infiltrometer (MDI) test takes less time, is less subjective, and provides a relative infiltration rate. For each test, the porous...

The effect of trees on preferential flow and soil infiltrability in an agroforestry parkland in semiarid Burkina Faso

NASA Astrophysics Data System (ADS)

Bargués Tobella, A.; Reese, H.; Almaw, A.; Bayala, J.; Malmer, A.; Laudon, H.; Ilstedt, U.

2014-04-01

Water scarcity constrains the livelihoods of millions of people in tropical drylands. Tree planting in these environments is generally discouraged due to the large water consumption by trees, but this view may neglect their potential positive impacts on water availability. The effect of trees on soil hydraulic properties linked to groundwater recharge is poorly understood. In this study, we performed 18 rainfall simulations and tracer experiments in an agroforestry parkland in Burkina Faso to investigate the effect of trees and associated termite mounds on soil infiltrability and preferential flow. The sampling points were distributed in transects each consisting of three positions: (i) under a single tree, (ii) in the middle of an open area, and (iii) under a tree associated with a termite mound. The degree of preferential flow was quantified through parameters based on the dye infiltration patterns, which were analyzed using image analysis of photographs. Our results show that the degree of preferential flow was highest under trees associated with termite mounds, intermediate under single trees, and minimal in the open areas. Tree density also had an influence on the degree of preferential flow, with small open areas having more preferential flow than large ones. Soil infiltrability was higher under single trees than in the open areas or under trees associated with a termite mound. The findings from this study demonstrate that trees have a positive impact on soil hydraulic properties influencing groundwater recharge, and thus such effects must be considered when evaluating the impact of trees on water resources in drylands.

Misrepresentation of hydro-erosional processes in rainfall simulations using disturbed soil samples

NASA Astrophysics Data System (ADS)

Thomaz, Edivaldo L.; Pereira, Adalberto A.

2017-06-01

Interrill erosion is a primary soil erosion process which consists of soil detachment by raindrop impact and particle transport by shallow flow. Interill erosion affects other soil erosion sub-processes, e.g., water infiltration, sealing, crusting, and rill initiation. Interrill erosion has been widely studied in laboratories, and the use of a sieved soil, i.e., disturbed soil, has become a standard method in laboratory experiments. The aims of our study are to evaluate the hydro-erosional response of undisturbed and disturbed soils in a laboratory experiment, and to quantify the extent to which hydraulic variables change during a rainstorm. We used a splash pan of 0.3 m width, 0.45 m length, and 0.1 m depth. A rainfall simulation of 58 mm h- 1 lasting for 30 min was conducted on seven replicates of undisturbed and disturbed soils. During the experiment, several hydro-physical parameters were measured, including splashed sediment, mean particle size, runoff, water infiltration, and soil moisture. We conclude that use of disturbed soil samples results in overestimation of interrill processes. Of the nine assessed parameters, four displayed greater responses in the undisturbed soil: infiltration, topsoil shear strength, mean particle size of eroded particles, and soil moisture. In the disturbed soil, five assessed parameters displayed greater responses: wash sediment, final runoff coefficient, runoff, splash, and sediment yield. Therefore, contextual soil properties are most suitable for understanding soil erosion, as well as for defining soil erodibility.

Environmental Technology Verification Report: Grouts for Wastewater Collection Systems, Avanti International AV-118 Acrylic Chemical Grout

EPA Science Inventory

Municipalities are discovering rapid degradation of infrastructures in wastewater collection and treatment facilities due to the infiltration of water from the surrounding environments. Wastewater facilities are not only wet, but also experience hydrostatic pressure conditions un...

[Effects of rainfall intensity on rainfall infiltration and redistribution in soil on Loess slope land].

PubMed

Li, Yi; Shao, Ming'an

2006-12-01

With simulation test, this paper studied the patterns of rainfall infiltration and redistribution in soil on typical Loess slope land, and analyzed the quantitative relations between the infiltration and redistribution and the movement of soil water and mass, with rainfall intensity as the main affecting factor. The results showed that rainfall intensity had significant effects on the rainfall infiltration and water redistribution in soil, and the microcosmic movement of soil water. The larger the rainfall intensity, the deeper the wetting front of rainfall infiltration and redistribution was, and the wetting front of soil water redistribution had a slower increase velocity than that of rainfall infiltration. The power function of the wetting front with time, and also with rainfall intensity, was fitted well. There was also a quantitative relation between the wetting front of rainfall redistribution and the duration of rainfall. The larger the rainfall intensity, the higher the initial and steady infiltration rates were, and the cumulative infiltration increased faster with time. Moreover, the larger the rainfall intensity, the smaller the wetting front difference was at the top and the end of the slope. With the larger rainfall intensity, both the difference of soil water content and its descending trend between soil layers became more obvious during the redistribution process on slope land.

Determination of infiltration and percolation rates along a reach of the Santa Fe River near La Bajada, New Mexico

USGS Publications Warehouse

Thomas, Carole L.; Stewart, Amy E.; Constantz, Jim E.

2000-01-01

Two methods, one a surface-water method and the second a ground-water method, were used to determine infiltration and percolation rates along a 2.5-kilometer reach of the Santa Fe River near La Bajada, New Mexico. The surface-water method uses streamflow measurements and their differences along a stream reach, streamflow-loss rates, stream surface area, and evaporation rates to determine infiltration rates. The ground-water method uses heat as a tracer to monitor percolation through shallow streambed sediments. Data collection began in October 1996 and continued through December 1997. During that period the stream reach was instrumented with three streamflow gages, and temperature profiles were monitored from the stream-sediment interface to about 3 meters below the streambed at four sites along the reach. Infiltration is the downward flow of water through the stream- sediment interface. Infiltration rates ranged from 92 to 267 millimeters per day for an intense measurement period during June 26- 28, 1997, and from 69 to 256 millimeters per day during September 27-October 6, 1997. Investigators calculated infiltration rates from streamflow loss, stream surface-area measurements, and evaporation-rate estimates. Infiltration rates may be affected by unmeasured irrigation-return flow in the study reach. Although the amount of irrigation-return flow was none to very small, it may result in underestimation of infiltration rates. The infiltration portion of streamflow loss was much greater than the evaporation portion. Infiltration accounted for about 92 to 98 percent of streamflow loss. Evaporation-rate estimates ranged from 3.4 to 7.6 millimeters per day based on pan-evaporation data collected at Cochiti Dam, New Mexico, and accounted for about 2 to 8 percent of streamflow loss. Percolation is the movement of water through saturated or unsaturated sediments below the stream-sediment interface. Percolation rates ranged from 40 to 109 millimeters per day during June 26-28, 1997. Percolation rates were not calculated for the September 27-October 6, 1997, period because a late summer flood removed the temperature sensors from the streambed. Investigators used a heat-and-water flow model, VS2DH (variably saturated, two- dimensional heat), to calculate near-surface streambed infiltration and percolation rates from temperatures measured in the stream and streambed. Near the stream-sediment interface, infiltration and percolation rates are comparable. Comparison of infiltration and percolation rates showed that infiltration rates were greater than percolation rates. The method used to calculate infiltration rates accounted for net loss or gain over the entire stream reach, whereas the method used to calculate percolation was dependent on point measurements and, as applied in this study, neglected the nonvertical component of heat and water fluxes. In general, using the ground-water method was less labor intensive than making a series of streamflow measurements and relied on temperature, an easily measured property. The ground-water method also eliminated the difficulty of measuring or estimating evaporation from the water surface and was therefore more direct. Both methods are difficult to use during periods of flood flow. The ground-water method has problems with the thermocouple-wire temperature sensors washing out during flood events. The surface- water method often cannot be used because of safety concerns for personnel making wading streamflow measurements.

The role of contact angle on unstable flow formation during infiltration and drainage in wettable porous media

NASA Astrophysics Data System (ADS)

Wallach, Rony; Margolis, Michal; Graber, Ellen R.

2013-10-01

The impact of contact angle on 2-D spatial and temporal water-content distribution during infiltration and drainage was experimentally studied. The 0.3-0.5 mm fraction of a quartz dune sand was treated and turned subcritically repellent (contact angle of 33°, 48°, 56°, and 75° for S33, S48, S56, and S75, respectively). The media were packed uniformly in transparent flow chambers and water was supplied to the surface as a point source at different rates (1-20 ml/min). A sequence of gray-value images was taken by CCD camera during infiltration and subsequent drainage; gray values were converted to volumetric water content by water volume balance. Narrow and long plumes with water accumulation behind the downward moving wetting front (tip) and negative water gradient above it (tail) developed in the S56 and S75 media during infiltration at lower water application rates. The plumes became bulbous with spatially uniform water-content distribution as water application rates increased. All plumes in these media propagated downward at a constant rate during infiltration and did not change their shape during drainage. In contrast, regular plume shapes were observed in the S33 and S48 media at all flow rates, and drainage profiles were nonmonotonic with a transition plane at the depth that water reached during infiltration. Given that the studied media have similar pore-size distributions, the conclusion is that imbibition hindered by the nonzero contact angle induced pressure buildup at the wetting front (dynamic water-entry value) that controlled the plume shape and internal water-content distribution during infiltration and drainage.

Can ash clog soil pores?

NASA Astrophysics Data System (ADS)

Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

2015-04-01

Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands evaluated here. Infiltration reductions and increases in runoff in these systems are more likely caused by the hydrologic effects of the textural interface between ash and soil, or by other fire-induced changes such as vegetation removal, decrease in roughness, and changes in soil water repellency. This is important information for determining the desired focus of post-fire management activities.

Modelling infiltration processes in frozen soils

NASA Astrophysics Data System (ADS)

Ireson, A. M.; Barbour, L. S.

2014-12-01

Understanding the hydrological processes in soils subject to significant freeze-thaw is fraught by "experimental vagaries and theoretical imponderables" (Miller 1980, Applications of soil physics). The infiltration of snowmelt water and the subsequent transmission of unfrozen water during thawing, is governed by hydraulic conductivity values which are changing with both ice and unfrozen water content. Water held within pores is subject to capillary forces, which results in a freezing point depression (i.e. water remains in the liquid state slightly below 0°C). As the temperature drops below zero, water freezes first in the larger pores, and then in progressively smaller pores. Since the larger pores also are the first to empty by drainage, these pores may be air filled during freezing, while smaller water filled pores freeze. This explains why an unsaturated, frozen soil may still have a considerable infiltration capacity. Infiltration into frozen soil is a critical phenomena related to the risk of flooding in the Canadian prairies, controlling the partitioning of snowmelt into either infiltration or runoff. We propose a new model, based on conceptualizing the pore space as a bundle of capillary tubes (with significant differences to the capillary bundle model of Wannatabe and Flury, 2008, WRR, doi:10.1029/2008WR007102) which allows any air-filled macropores to contribute to the potential infiltration capacity of the soil. The patterns of infiltration and water movement during freeze-thaw from the model are compared to field observations from the Canadian prairies and Boreal Plains.

Ecological engineering to control bioclogging: an original field study coupling infiltration and biological measurements

NASA Astrophysics Data System (ADS)

Gette-bouvarot, Morgane; Mermillod-Blondin, Florian; Lassabatere, Laurent; Lemoine, Damien; Delolme, Cécile; Volatier, Laurence

2014-05-01

Infiltration systems are increasingly used in urban areas for several purposes such as flood prevention and groundwater recharge. However, their functioning is often impacted by clogging that leads to decreases in hydraulic and water treatment performances. These systems are commonly built with sand as infiltration medium, a media subject to rapid clogging by the combined and overlapping processes of pore occlusion by fine particles and biofilm development. In a previous study, we pointed out that the phototrophic component of biofilms developed at the surface layer of infiltration systems (algae, cyanobacteria) could reduce by up to 60-fold the saturated hydraulic conductivity. Consequently, it appears crucial to control biofilm growth to maintain porous infiltration media performances. The present study aimed to test the influence of biotic (addition of animals or macrophytes) and abiotic (light reduction) treatments on biofilm development and associated hydraulic properties in an infiltration device dedicated to aquifer recharge with river water in Lyon Area (France). Twenty-five benthic enclosures were used to test 5 "treatments" on non-manipulated surface layer under field conditions. Three biotic treatments consisted in the introduction of: (i) an invertebrate acting as algae grazer (Viviparus viviparus), (ii) an invertebrate that digs galleries in sediments (Tubifex tubifex), and (iii) a macrophyte that could inhibit benthic biofilm by allelopathic activity (Vallisneria spiralis L). The fourth treatment was designed to simulate shading. The last "treatment" was a control which monitored the evolution of the system during the experiment without manipulation (addition of macro-organisms or shading). Each treatment was replicated five times. The experiment was conducted for 6 weeks, and sampling of the surface layer (0-1 cm) was carried out in each enclosure at the beginning (t0) and the end (tf). We coupled biological characterizations (organic matter, algal biomass, bacterial abundances, microbial enzymatic activities, EPS composition, and photosynthetic efficiency) with in situ hydraulic conductivity measurements (falling head method, five measures per enclosure at t0 and tf). Our results showed that some treatments could regulate benthic biofilm growth and improve infiltration rate. For instance, V. viviparus treatment resulted in a decrease in chlorophyll-a, EPS sugar and protein contents and an associated increase of infiltration rate, while it decreased in the control treatment. These results are very promising for the future development of ecological engineering solutions to prevent biological clogging in systems dedicated to infiltration. To our knowledge, this study is the first to highlight such potential role of macro-organisms under field conditions.

Hydraulic characterization of a sealed loamy soil in a Mediterranean vineyard

NASA Astrophysics Data System (ADS)

Alagna, Vincenzo; Di Prima, Simone; Bagarello, Vincenzo; Guaitoli, Fabio; Iovino, Massimo; Keesstra, Saskia; Cerdà, Artemi

2017-04-01

Water infiltration measurements constitute a common way for an indirect characterization of sealed/crusted soils (Alagna et al., 2013). The Beerkan Estimation of Soil Transfer (BEST) parameters procedure by Lassabatere et al. (2006) is very attractive for practical use since it allows an estimation of both the soil water retention and hydraulic conductivity functions. The BEST method considers certain analytical formulae for the hydraulic characteristic curves and estimates their shape parameters, which are texture dependent, from particle-size analysis by physical-empirical pedotransfer functions. Structure dependent scale parameters are estimated by a beerkan experiment, i.e. a three-dimensional (3D) field infiltration experiment at ideally zero pressure head. BEST substantially facilitates the hydraulic characterization of unsaturated soils, and it is gaining popularity in soil science (Bagarello et al., 2014a; Di Prima, 2015; Di Prima et al., 2016b). Bagarello et al. (2014b) proposed a beerkan derived procedure to explain surface runoff and disturbance phenomena at the soil surface occurring during intense rainfall events. Di Prima et al. (2016a) applied this methodology in a vineyard with a sandy-loam texture. These authors compared this simple methodology with rainfall simulation experiments establishing a physical link between the two methodologies through the kinetic energy of the rainfall and the gravitational potential energy of the water used for the beerkan runs. They also indirectly demonstrated the occurrence of a certain degree of compaction and mechanical breakdown using a minidisk infiltrometer (Decagon, 2014). With this device, they reported a reduction of the unsaturated hydraulic conductivity by 2.3 times, due to the seal formation. The ability of the BEST method to distinguish between crusted and non-crusted soils was demonstrated by Souza et al. (2014). However, the potential of the beerkan runs to detect the effect of the seal on flow and BEST estimates is still largely unknown since only a few investigations have been carried out. In this study, the BEST method was applied to check the impact of sealing on soil hydraulic conductivity in a Mediterranean vineyard (western Sicily, Italy) under conventional tillage. An area of approximately 150 m2 was sampled on three different sampling campaigns covering two growing seasons. Beerkan infiltration experiments were carried out along the rows direction and in the inter-row areas. A 55 mm rainfall event that occurred between the first and second sampling campaigns contributed to form a sealed layer at the soil surface. The presence of the seal implied that the saturated soil hydraulic conductivity, Ks, was 1.5-1.8 times lower than that measured in the absence of the sealed layer. The seal layer only affected water infiltration between the rows, suggesting that the protective role of vegetation along the rows was effective. The tillage practices carried out in the spring 2016 removed any existing surface sealed layer and thereby increased soil infiltration properties, suggesting a cycling occurrence of layering phenomena within the year. In fact, differences between the Ks values measured between the rows (second against first and third sampling campaigns) were statistically significant. In this investigation, the sampling strategy implying beerkan tests carried out along and between the vine-rows was successfully applied. This strategy allowed to assess the reduction in hydraulic conductivity with extemporaneous measurements alone. Its main advantage is that it allows a rapid assessment of sealing severity affecting water infiltration taking advantage of the protective role of the vegetation along the rows. In conclusion, the hypothesis that the beerkan runs are suitable enough to detect the effect of the seal on flow and Ks values estimated by BEST was reasonable. In the future, testing the proposed procedure in conjunction with others field methodologies for soil hydraulic characterization implying alteration at the soil surface, such as rainfall simulation experiments or the beerkan derived procedure discussed above, should contribute to a better understanding of sealing severity affecting water infiltration on bare soils. Ring insertion for the infiltration run does not seem to alter the sealed layer but more investigations are required with reference to this point. Acknowledgements This study was supported by grants from the Research Project CISV under grant n˚ 2014COMM-0363 CUP 872114000570002. References Alagna, V., Bagarello, V., Di Prima, S., Giordano, G. and Iovino, M.: A simple field method to measure the hydrodynamic properties of soil surface crust, Journal of Agricultural Engineering, 44(25), 74-79, doi:10.4081/jae.2013.(s1):e14, 2013. Bagarello, V., Di Prima, S., Giordano, G. and Iovino, M.: A test of the Beerkan Estimation of Soil Transfer parameters (BEST) procedure, Geoderma, 221-222, 20-27, doi:10.1016/j.geoderma.2014.01.017, 2014a. Bagarello, V., Castellini, M., Di Prima, S. and Iovino, M.: Soil hydraulic properties determined by infiltration experiments and different heights of water pouring, Geoderma, 213, 492-501, doi:10.1016/j.geoderma.2013.08.032, 2014b. Decagon: Minidisk Infiltrometer User's Manual, Decagon Devices, Inc., Pullman, USA, 24, 2014. Di Prima, S.: Automated single ring infiltrometer with a low-cost microcontroller circuit, Computers and Electronics in Agriculture, 118, 390-395, doi:10.1016/j.compag.2015.09.022, 2015. Di Prima, S., Bagarello, V., Angulo-Jaramillo, R., Bautista, I., Burguet, M., Cerdà, A., Iovino, M., Lassabatère, L. and Prosdocimi, M.: Comparing Beerkan infiltration tests with rainfall simulation experiments for hydraulic characterization of a sandy-loam soil, Submitted to Hydrological Processes, 2016a. Di Prima, S., Lassabatere, L., Bagarello, V., Iovino, M. and Angulo-Jaramillo, R.: Testing a new automated single ring infiltrometer for Beerkan infiltration experiments, Geoderma, 262, 20-34, doi:10.1016/j.geoderma.2015.08.006, 2016b. Lassabatere, L., Angulo-Jaramillo, R., Soria Ugalde, J. M., Cuenca, R., Braud, I. and Haverkamp, R.: Beerkan Estimation of Soil Transfer Parameters through Infiltration Experiments—BEST, Soil Science Society of America Journal, 70(2), 521, doi:10.2136/sssaj2005.0026, 2006. Souza, E. S., Antonino, A. C. D., Heck, R. J., Montenegro, S. M. G. L., Lima, J. R. S., Sampaio, E. V. S. B., Angulo-Jaramillo, R. and Vauclin, M.: Effect of crusting on the physical and hydraulic properties of a soil cropped with Castor beans (Ricinus communis L.) in the northeastern region of Brazil, Soil and Tillage Research, 141, 55-61, doi:10.1016/j.still.2014.04.004, 2014.

LNAPL Removal from Unsaturated Porous Media using Surfactant Infiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong, Lirong; Oostrom, Martinus

A series of unsaturated column experiments was performed to evaluate light non-aqueous phase liquid (LNAPL) fate and removal during surfactant solution infiltration. Surfactant-LNAPL phase behavior tests were conducted to optimize the remedial solutions. Packed sand and site sediment columns were first processed to establish representative LNAPL smear zone under unsaturated conditions. Infiltration of low-concentration surfactant was then applied in a stepwise flush mode, with 0.3 column pore volume (PV) of solution in each flush. The influence of infiltrated surfactant solution volume and pH on LNAPL removal was assessed. A LNAPL bank was observed at the very front of the firstmore » surfactant infiltration in each column, indicating that a very low surfactant concentration is needed to reduce the LNAPL-water interfacial tension sufficiently enough to mobilize trapped LNAPL under unsaturated conditions. More LNAPL was recovered as additional steps of surfactant infiltration were applied. Up to 99% LNAPL was removed after six infiltration steps, with less than 2.0 PV of total surfactant solution application, suggesting surfactant infiltration may be an effective method for vadose zone LNAPL remediation. The influence of pH tested in this study (3.99~10.85) was insignificant because the buffering capacity of the sediment kept the pH in the column higher than the zero point charge, pHzpc, of the sediment and therefore the difference between surfactant sorption was negligible.« less

Stormwater infiltration and the 'urban karst' - A review

NASA Astrophysics Data System (ADS)

Bonneau, Jeremie; Fletcher, Tim D.; Costelloe, Justin F.; Burns, Matthew J.

2017-09-01

The covering of native soils with impervious surfaces (e.g. roofs, roads, and pavement) prevents infiltration of rainfall into the ground, resulting in increased surface runoff and decreased groundwater recharge. When this excess water is managed using stormwater drainage systems, flow and water quality regimes of urban streams are severely altered, leading to the degradation of their ecosystems. Urban streams restoration requires alternative approaches towards stormwater management, which aim to restore the flow regime towards pre-development conditions. The practice of stormwater infiltration-achieved using a range of stormwater source-control measures (SCMs)-is central to restoring baseflow. Despite this, little is known about what happens to the infiltrated water. Current knowledge about the impact of stormwater infiltration on flow regimes was reviewed. Infiltration systems were found to be efficient at attenuating high-flow hydrology (reducing peak magnitudes and frequencies) at a range of scales (parcel, streetscape, catchment). Several modelling studies predict a positive impact of stormwater infiltration on baseflow, and empirical evidence is emerging, but the fate of infiltrated stormwater remains unclear. It is not known how infiltrated water travels along the subsurface pathways that characterise the urban environment, in particular the 'urban karst', which results from networks of human-made subsurface pathways, e.g. stormwater and sanitary sewer pipes and associated high permeability trenches. Seepage of groundwater into and around such pipes is possible, meaning some infiltrated stormwater could travel along artificial pathways. The catchment-scale ability of infiltration systems to restore groundwater recharge and baseflow is thus ambiguous. Further understanding of the fate of infiltrated stormwater is required to ensure infiltration systems deliver optimal outcomes for waterway flow regimes.

Electrical Imaging of Infiltration in Agricultural Soils on Long Island, New York

NASA Astrophysics Data System (ADS)

Lampousis, A.; Kenyon, P. M.; Sanwald, K.; Steiner, N.

2007-12-01

High resolution electrical resistivity imaging of vadose zone infiltration experiments was conducted on agricultural soils by the City College and Graduate Center of CUNY, in cooperation with Cornell University's Agricultural Stewardship Program and Long Island Horticultural Research and Extension Center (LIHREC) in Riverhead, New York. Measurements were made in active vineyards with a commercial resistivity imaging system, using a half- meter electrode spacing. Soils considered were Riverhead sandy loam (RdA), Haven loam (HaA), and Bridgehampton silty loam (BgA). The Riverhead and Haven soils are the most common types found on eastern Long Island. The Bridgehampton is considered the most fertile. Soil samples and measurements of soil compaction were collected at the same time as the geophysical measurements. In addition, remote sensing data were obtained for the three sites and processed to produce normalized difference vegetation index (NDVI) data to evaluate potential correlations between vegetation vigor, soil texture and water migration patterns. Applications of this study include continuous water content monitoring in high value cash crops (precision agriculture). Changes in electrical resistivity during infiltration are clearly visible at all three locations. Preliminary analysis of the results shows correlations of baseline resistivity with particle size distributions and correlations between changes in resistivity during infiltration and soil compaction data. Time-lapse electrical images of the three sites will also be compared with published properties for these soils, including particle size distribution, saturated hydraulic conductivity, available water capacity, and surface texture.

The Effects of More Extreme Rainfall Patterns on Infiltration and Nutrient Losses in Agricultural Soils

NASA Astrophysics Data System (ADS)

Hess, L.; Basso, B.; Hinckley, E. L. S.; Robertson, G. P.; Matson, P. A.

2015-12-01

In the coming century, the proportion of total rainfall that falls in heavy storm events is expected to increase in many areas, especially in the US Midwest, a major agricultural region. These changes in rainfall patterns may have consequences for hydrologic flow and nutrient losses, especially in agricultural soils, with potentially negative consequences for receiving ground- and surface waters. We used a tracer experiment to examine how more extreme rainfall patterns may affect the movement of water and solutes through an agricultural soil profile in the upper Midwest, and to what extent tillage may moderate these effects. Two rainfall patterns were created with 5m x 5m rainout shelters at the Kellogg Biological Station LTER site in replicated plots with either conventional tillage or no-till management. Control rainfall treatments received water 3x per week, and extreme rainfall treatments received the same total amount of water but once every two weeks, to simulate less frequent but larger storms. In April 2015, potassium bromide (KBr) was added as a conservative tracer of water flow to all plots, and Br- concentrations in soil water at 1.2m depth were measured weekly from April through July. Soil water Br- concentrations increased and peaked more quickly under the extreme rainfall treatment, suggesting increased infiltration and solute transfer to depth compared to soils exposed to control rainfall patterns. Soil water Br- also increased and peaked more quickly in no-till than in conventional tillage treatments, indicating differences in flow paths between management systems. Soil moisture measured every 15 minutes at 10, 40, and 100cm depths corroborates tracer experiment results: rainfall events simulated in extreme rainfall treatments led to large increases in deep soil moisture, while the smaller rainfall events simulated under control conditions did not. Deep soil moisture in no-till treatments also increased sooner after water application as compared to in conventional soils. Our results suggest that exposure to more extreme rainfall patterns will likely increase infiltration depth and nutrient losses in agricultural soils. In particular, soils under no-till management, which leads to development of preferential flow paths, may be particularly vulnerable to vertical nutrient losses.

Difficulties in the evaluation and measuring of soil water infiltration

NASA Astrophysics Data System (ADS)

Pla-Sentís, Ildefonso

2013-04-01

Soil water infiltration is the most important hydrological parameter for the evaluation and diagnosis of the soil water balance and soil moisture regime. Those balances and regimes are the main regulating factors of the on site water supply to plants and other soil organisms and of other important processes like runoff, surface and mass erosion, drainage, etc, affecting sedimentation, flooding, soil and water pollution, water supply for different purposes (population, agriculture, industries, hydroelectricity), etc. Therefore the evaluation and measurement of water infiltration rates has become indispensable for the evaluation and modeling of the previously mentioned processes. Infiltration is one of the most difficult hydrological parameters to evaluate or measure accurately. Although the theoretical aspects of the process of soil water infiltration are well known since the middle of the past century, when several methods and models were already proposed for the evaluation of infiltration, still nowadays such evaluation is not frequently enough accurate for the purposes being used. This is partially due to deficiencies in the methodology being used for measuring infiltration, including some newly proposed methods and equipments, and in the use of non appropriate empirical models and approaches. In this contribution we present an analysis and discussion about the main difficulties found in the evaluation and measurement of soil water infiltration rates, and the more commonly committed errors, based on the past experiences of the author in the evaluation of soil water infiltration in many different soils and land conditions, and in their use for deducing soil water balances under variable and changing climates. It is concluded that there are not models or methods universally applicable to any soil and land condition, and that in many cases the results are significantly influenced by the way we use a particular method or instrument, and by the alterations in the soil conditions by the land management, but also due to the manipulation of the soil before and during the measurement. Direct "in situ" field evaluations have to be preferred in any case to indirect deductions from other soil characteristics measured under laboratory conditions in the same soils, or in other soils, through the so called "pedo-transfer" functions, or through the use of stochastic models such as the SCS Curve Number Method, or of other models using empirical or physical approaches, which have demonstrated to be of limited value in most of the cases. References Philip, J. R., 1954., An infiltration equation with physical significance: Soil Sci..,v. 77, p. 153-157. Philip, J. R., 1958. The theory of infiltration, pt. 7: Soil Sci., v. 85, no. 6, p. 333-337. Pla, I.1981. Simuladores de lluvia para el estudio de relaciones suelo-agua bajo agricultura de secano en los trópicos. Rev. Fac. Agron. XII(1-2):81-93.Maracay (Venezuela) Pla, I. 1986. A routine laboratory index to predict the effects of soil sealing on soil and water conservation. En "Assesment of Soil Surface Sealing and Crusting". 154-162.State Univ. of Ghent.Gante (Bélgica Pla, I., 1997. A soil water balance model for monitoring soil erosion processes and effects on steep lands in the tropics. Soil Technology. 11(1):17-30. Elsevier Pla, I., M.C. Ramos, S. Nacci, F. Fonseca y X. Abreu. 2005. Soil moisture regime in dryland vineyards of Catalunya (Spain) as influenced by climate, soil and land management. "Integrated Soil and Water Management for Orchard Development". FAO Land and Water Bulletin 10. 41-49. Roma (Italia). Pla, I., 2006. Hydrological approach for assessing desertification processes in the Mediterranean region. In W.G. Kepner et al. (Editors), Desertification in the Mediterranean Region. A Security Issue. 579-600 Springer. Heidelberg (Germany) Pla, I. 2011. Evaluación y Modelización Hidrológica para el Diagnóstico y Prevención de "Desastres Naturales". Gestión y Ambiente 14 (3): 17-22. UN-Medellín (Colombia). ISSN 0124.177X Pla, I. 2011. Medición y evaluación de propiedades físicas de los suelos: dificultades y errores más frecuentes. II-Propiedades hidrológicas. Suelos Ecuatoriales 40 (2): 94-127 Reynolds W.D., B.T. Bowman, R.R. Brunke, C.F. Drury and C.S. Tan. 2000. Comparison of Tension Infiltrometer, Pressure Infiltrometer, and Soil Core Estimates of Saturated Hydraulic Conductivity . Soil Science Society of America Journal 64:478-484 Richards, L. A., 1952. Report of the Subcommittee on Permeability and Infiltration, Committee on Terminology, Soil Science Society of America: Soil Sci. Soc.America Proc., v. 16, p. 85-88. Segal, E., S.A.Bradford, P. Shouse; N. Lazarovich, and D. Corwin. 2008. Integration of Hard and Soft Data to Characterize Field-Scale Hydraulic Properties for Flow and Transport Studies. Vadose Zone J 7:878-889 Young, E. 1991. Infiltration measurements, a review. Hydrological processes 5: 309-320

Preliminary estimates of spatially distributed net infiltration and recharge for the Death Valley region, Nevada-California

USGS Publications Warehouse

Hevesi, J.A.; Flint, A.L.; Flint, L.E.

2002-01-01

A three-dimensional ground-water flow model has been developed to evaluate the Death Valley regional flow system, which includes ground water beneath the Nevada Test Site. Estimates of spatially distributed net infiltration and recharge are needed to define upper boundary conditions. This study presents a preliminary application of a conceptual and numerical model of net infiltration. The model was developed in studies at Yucca Mountain, Nevada, which is located in the approximate center of the Death Valley ground-water flow system. The conceptual model describes the effects of precipitation, runoff, evapotranspiration, and redistribution of water in the shallow unsaturated zone on predicted rates of net infiltration; precipitation and soil depth are the two most significant variables. The conceptual model was tested using a preliminary numerical model based on energy- and water-balance calculations. Daily precipitation for 1980 through 1995, averaging 202 millimeters per year over the 39,556 square kilometers area of the ground-water flow model, was input to the numerical model to simulate net infiltration ranging from zero for a soil thickness greater than 6 meters to over 350 millimeters per year for thin soils at high elevations in the Spring Mountains overlying permeable bedrock. Estimated average net infiltration over the entire ground-water flow model domain is 7.8 millimeters per year.To evaluate the application of the net-infiltration model developed on a local scale at Yucca Mountain, to net-infiltration estimates representing the magnitude and distribution of recharge on a regional scale, the net-infiltration results were compared with recharge estimates obtained using empirical methods. Comparison of model results with previous estimates of basinwide recharge suggests that the net-infiltration estimates obtained using this model may overestimate recharge because of uncertainty in modeled precipitation, bedrock permeability, and soil properties for locations such as the Spring Mountains. Although this model is preliminary and uncalibrated, it provides a first approximation of the spatial distribution of net infiltration for the Death Valley region under current climatic conditions.

Relation of pathways and transit times of recharge water to nitrate concentrations using stable isotopes

USGS Publications Warehouse

Landon, M.K.; Delin, G.N.; Komor, S.C.; Regan, C.P.

2000-01-01

Oxygen and hydrogen stable isotope values of precipitation, irrigation water, soil water, and ground water were used with soil-moisture contents and water levels to estimate transit times and pathways of recharge water in the unsaturated zone of a sand and gravel aquifer. Nitrate-nitrogen (nitrate) concentrations in ground water were also measured to assess their relation to seasonal recharge. Stable isotope values indicated that recharge water usually had a transit time through the unsaturated zone of several weeks to months. However, wetting fronts usually moved through the unsaturated zone in hours to weeks. The much slower transit of isotopic signals than that of wetting fronts indicates that recharge was predominantly composed of older soil water that was displaced downward by more recent infiltrating water. Comparison of observed and simulated isotopic values from pure-piston flow and mixing-cell water and isotope mass balance models indicates that soil water isotopic values were usually highly mixed. Thus, movement of recharge water did not occur following a pure piston-flow displacement model but rather follows a hydrid model involving displacement of mixed older soil water with new infiltration water. An exception to this model occurred in a topographic depression, where movement of water along preferential flowpaths to the water table occurred within hours to days following spring thaw as result of depression-focused infiltration of snow melt. In an adjacent upland area, recharge of snow melt occurred one to two months later. Increases in nitrate concentrations at the water table during April-May 1993 and 1994 in a topographic lowland within a corn field were related to recharge of water that had infiltrated the previous summer and was displaced from the unsaturated zone by spring infiltration. Increases in nitrate concentrations also occurred during July-August 1994 in response to recharge of water that infiltrated during May-August 1994. These results indicate that the largest ground water nitrate concentrations were associated with recharge of water that infiltrated into the soil during May-August, when most nitrogen fertilizer was applied.

Hydrogeology, degradation of ground-water quality, and simulation of infiltration from the Delaware River into the Potomac aquifers, northern Delaware

USGS Publications Warehouse

Phillips, S.W.

1987-01-01

Brackish water is infiltrating from the Delaware River into the underlying Potomac aquifers in the Cretaceous Potomac Formation in northern Delaware. Evidence that infiltration at the river is actually occurring includes chloride concentrations in the aquifers that are above ambient levels and chemical characteristics of groundwater and river water that are similar. Water quality within the Potomac aquifers has been degraded by the infiltration of river water and by leachate from waste disposal sites. The ambient groundwater has chloride concentrations from 10 to 21 mg/L. Chemical analyses indicate that the ambient groundwater is a sodium magnesium calcium-chloride sulfate bicarbonate type. Areas of the Potomac aquifers that have been degraded have chloride concentrations from 40 to 8,600 m/L, with specific conductances of 200 to 27 ,200 microsiemens/cm at 25 C. Chemical analyses indicate the groundwater in these areas is a sodium-chlorate type. Two wells in the lower Potomac aquifer near the Wilmington Marine Terminal also have been affected by the infiltration of river water. Leachate from waste disposal sites has caused localized groundwater degradation in all three Potomac aquifers, especially north of the Delaware Memorial Bridge and at sites near Army Creek and Red Lion Creek. Chloride concentrations up to 8,600 mg/L have resulted from waste disposal leachate. Simulated infiltration of river water into the Potomac aquifers accounts for approximately 6 to 12% of the total aquifer recharge in the area of influence of the pumping. There is a direct correlation between the rate of infiltration of river water and the total well-field pumpage. The rate of infiltration of river water for the pumping scenarios ranged from 0.31 to 0.62 million gal/day. Simulations of freshwater injection demonstrated that 12 barriers wells, each injecting 300 gal/min, would be needed to create a barrier against the infiltration of river water in the upper Potomac aquifer, whereas the middle Potomac aquifer would require 7 wells in injecting 200 gal/min. (Author 's abstract)

Wetting properties of fungi mycelium alter soil infiltration and soil water repellency in a γ-sterilized wettable and repellent soil.

PubMed

Chau, Henry Wai; Goh, Yit Kheng; Vujanovic, Vladimir; Si, Bing Cheng

2012-12-01

Soil water repellency (SWR) has a drastic impact on soil quality resulting in reduced infiltration, increased runoff, increased leaching, reduced plant growth, and increased soil erosion. One of the causes of SWR is hydrophobic fungal structures and exudates that change the soil-water relationship. The objective of this study was to determine whether SWR and infiltration could be manipulated through inoculation with fungi. The effect of fungi on SWR was investigated through inoculation of three fungal strains (hydrophilic -Fusarium proliferatum, chrono-amphiphilic -Trichoderma harzianum, and hydrophobic -Alternaria sp.) on a water repellent soil (WR-soil) and a wettable soil (W-soil). The change in SWR and infiltration was assessed by the water repellency index and cumulative infiltration respectively. F. proliferatum decreased the SWR on WR-soil and slightly increased SWR in W-soil, while Alternaria sp. increased SWR in both the W-soil and the WR-soil. Conversely T. harzianum increased the SWR in the W-soil and decreased the SWR in the WR-soil. All strains showed a decrease in infiltration in W-soil, while only the F. proliferatum and T. harzianum strain showed improvement in infiltration in the WR-soil. The ability of fungi to alter the SWR and enmesh soil particles results in changes to the infiltration dynamics in soil. Copyright © 2012 The British Mycological Society. Published by Elsevier Ltd. All rights reserved.

Effects of unsaturated zone on ground-water mounding

USGS Publications Warehouse

Sumner, D.M.; Rolston, D.E.; Marino, M.A.

1999-01-01

The design of infiltration basins used to dispose of treated wastewater or for aquifer recharge often requires estimation of ground-water mounding beneath the basin. However, the effect that the unsaturated zone has on water-table response to basin infiltration often has been overlooked in this estimation. A comparison was made between two methods used to estimate ground-water mounding-an analytical approach that is limited to the saturated zone and a numerical approach that incorporates both the saturated and the unsaturated zones. Results indicate that the error that is introduced by a method that ignores the effects of the unsaturated zone on ground-water mounding increases as the basin-loading period is shortened; as the depth to the water table increases, with increasing subsurface anisotropy; and with the inclusion of fine-textured strata. Additionally, such a method cannot accommodate the dynamic nature of basin infiltration, the finite transmission time of the infiltration front to the water table, or the interception of the basin floor by the capillary fringe.The design of infiltration basins used to dispose of treated wastewater or for aquifer recharge often requires estimation of ground-water mounding beneath the basin. However, the effect that the unsaturated zone has on water-table response to basin infiltration often has been overlooked in this estimation. A comparison was made between two methods used to estimate ground-water mounding - an analytical approach that is limited to the saturated zone and a numerical approach that incorporates both the saturated and the unsaturated zones. Results indicate that the error that is introduced by a method that ignores the effects of the unsaturated zone on ground-water mounding increases as the basin-loading period is shortened; as the depth to the water table increases, with increasing subsurface anisotropy; and with the inclusion of fine-textured strata. Additionally, such a method cannot accommodate the dynamic nature of basin infiltration, the finite transmission time of the infiltration front to the water, or the interception of the basin floor by the capillary fringe.

The influence of compost addition on the water repellency of brownfield soils

NASA Astrophysics Data System (ADS)

Whelan, Amii; Kechavarzi, Cedric; Sakrabani, Ruben; Coulon, Frederic; Simmons, Robert; Wu, Guozhong

2010-05-01

Compost application to brownfield sites, which can facilitate the stabilisation and remediation of contaminants whilst providing adequate conditions for plant growth, is seen as an opportunity to divert biodegradable wastes from landfill and put degraded land back into productive use. However, although compost application is thought to improve soil hydraulic functioning, there is a lack of information on the impact of large amounts of compost on soil water repellency. Water repellency in soils is attributed to the accumulation of hydrophobic organic compounds released as root exudates, fungal and microbial by-products and decomposition of organic matter. It has also been shown that brownfield soils contaminated with petroleum-derived organic contaminants can exhibit strong water repellency, preventing the rapid infiltration of water and leading potentially to surface run off and erosion of contaminated soil. However, hydrophobic organic contaminants are known to become sequestrated by partitioning into organic matter or diffusing into nano- and micropores, making them less available over time (ageing). The effect of large amounts of organic matter addition through compost application on the water repellency of soils contaminated with petroleum-derived organic contaminants requires further investigation. We characterised the influence of compost addition on water repellency in the laboratory by measuring the Water Drop Penetration Time (WDPT), sorptivity and water repellency index through infiltration experiments on soil samples amended with two composts made with contrasting feedstocks (green waste and predominantly meat waste). The treatments consisted of a sandy loam, a clay loam and a sandy loam contaminated with diesel fuel and aged for 3 years, which were amended with the two composts at a rate equivalent to 750t/ha. In addition core samples collected from a brownfield site, amended with compost at three different rates (250, 500 and 750t/ha) in 2007, were also tested. The results show that the water repellency of air dried samples is significantly higher in samples amended with composts and increases with increasing organic matter content. The WDPT suggests that compost, when dry, is hydrophobic. Diesel contamination leads to a decrease in sorptivity compared to uncontaminated controls and wettability is not re-established following the addition of compost. Finally, the increase in compost volume (i.e. application rate) in the field samples leads to an increase in water repellency. The infiltration tests, carried out using a miniature tension infiltrometer, also illustrate different effects of hydrophobicity on infiltration, with some samples demonstrating reduced infiltration and low sorptivity but others showing no infiltration at all until the breakdown of repellency at later times. This investigation is currently being complemented by a study of the influence of hydrophobic organic contaminant sequestration with time (i.e. ageing), estimated by measuring the changes in the available fraction of polycyclic aromatic hydrocarbons (PAHs), on the water repellency of compost amended brownfield soils.

Estimate of the soil water retention curve from the sorptivity and β parameter calculated from an upward infiltration experiment

NASA Astrophysics Data System (ADS)

Moret-Fernández, D.; Latorre, B.

2017-01-01

The water retention curve (θ(h)), which defines the relationship between the volumetric water content (θ) and the matric potential (h), is of paramount importance to characterize the hydraulic behaviour of soils. Because current methods to estimate θ(h) are, in general, tedious and time consuming, alternative procedures to determine θ(h) are needed. Using an upward infiltration curve, the main objective of this work is to present a method to determine the parameters of the van Genuchten (1980) water retention curve (α and n) from the sorptivity (S) and the β parameter defined in the 1D infiltration equation proposed by Haverkamp et al. (1994). The first specific objective is to present an equation, based on the Haverkamp et al. (1994) analysis, which allows describing an upward infiltration process. Secondary, assuming a known saturated hydraulic conductivity, Ks, calculated on a finite soil column by the Darcy's law, a numerical procedure to calculate S and β by the inverse analysis of an exfiltration curve is presented. Finally, the α and n values are numerically calculated from Ks, S and β. To accomplish the first specific objective, cumulative upward infiltration curves simulated with HYDRUS-1D for sand, loam, silt and clay soils were compared to those calculated with the proposed equation, after applying the corresponding β and S calculated from the theoretical Ks, α and n. The same curves were used to: (i) study the influence of the exfiltration time on S and β estimations, (ii) evaluate the limits of the inverse analysis, and (iii) validate the feasibility of the method to estimate α and n. Next, the θ(h) parameters estimated with the numerical method on experimental soils were compared to those obtained with pressure cells. The results showed that the upward infiltration curve could be correctly described by the modified Haverkamp et al. (1994) equation. While S was only affected by early-time exfiltration data, the β parameter had a significant influence on the long-time exfiltration curve, which accuracy increased with time. The 1D infiltration model was only suitable for β < 1.7 (sand, loam and silt). After omitting the clay soil, an excellent relationship (R2 = 0.99, p < 0.005) was observed between the theoretical α and n values of the synthetic soils and those estimated from the inverse analysis. Consistent results, with a significant relationship (p < 0.001) between the n values estimated with the pressure cell and the upward infiltration analysis, were also obtained on the experimental soils.

Interfacial spreading effects on one-dimensional organic liquid imbibition in water-wetted porous media

NASA Astrophysics Data System (ADS)

McBride, J. F.; Simmons, C. S.; Cary, J. W.

1992-10-01

The spreading coefficient, Csp, determines whether an organic immiscible liquid, OIL, will form a lens ( Csp < 0) or will spread spontaneously ( Csp > 0) on a water surface. An OIL that forms a lens does not perfectly wet the water surface and therefore has a contact angle greater than 0°. The one-dimensional rate at which an OIL spreads spontaneously on a water surface is proportional to the square root of Csp. Of the OIL's that pose a contaminant threat to the subsurface, the majority has a non-zero Csp. To test the influence of such interfacial spreading phenomena on OIL infiltration in a pristine vadose zone, upward OIL and water imbibition infiltration experiments were performed in glass-bead columns, moistened with water, by using OIL's with different Csp. An analytical model for saturated liquid front rise was used to inversely estimate the effective capillary pressure head at the front and the average liquid conductivity. A nonspreading OIL ( Csp ≪ 0) exhibited a reduced capillary pressure head in the water-wetted glass beads. A spontaneously spreading OIL ( Csp ≫0) manifested an enhanced capillary pressure head. Reduced capillary pressure head was associated with an increase in average conductivity, and enhanced capillary pressure head was associated with a decrease in average conductivity when compared to the average water conductivity during water imbibition. The employed experimental method and mathematical analysis of dynamic flow, subject to interfacial spreading phenomena, are practical for quantifying parameters for use in sharp-front OIL infiltration models, but more research is needed to determine how to incorporate the spreading coefficient in numerical multiphase flow models.

30 CFR 816.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... minimizes acidic, toxic, or other harmful infiltration to ground-water systems and by managing excavations... water by preventing erosion, the formation of polluted runoff, and the infiltration of polluted water...

30 CFR 816.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... minimizes acidic, toxic, or other harmful infiltration to ground-water systems and by managing excavations... water by preventing erosion, the formation of polluted runoff, and the infiltration of polluted water...

30 CFR 816.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... minimizes acidic, toxic, or other harmful infiltration to ground-water systems and by managing excavations... water by preventing erosion, the formation of polluted runoff, and the infiltration of polluted water...

40 CFR 440.131 - General provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... permitted. (e) Groundwater infiltration provision. In the event a new source subject to a no discharge requirement can demonstrate that groundwater infiltration contributes a substantial amount of water to the... volume of water equivalent to the amount of groundwater infiltration. This discharge shall be subject to...

40 CFR 440.131 - General provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... permitted. (e) Groundwater infiltration provision. In the event a new source subject to a no discharge requirement can demonstrate that groundwater infiltration contributes a substantial amount of water to the... volume of water equivalent to the amount of groundwater infiltration. This discharge shall be subject to...

40 CFR 440.131 - General provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... permitted. (e) Groundwater infiltration provision. In the event a new source subject to a no discharge requirement can demonstrate that groundwater infiltration contributes a substantial amount of water to the... volume of water equivalent to the amount of groundwater infiltration. This discharge shall be subject to...

Groundwater infiltration, surface water inflow and sewerage exfiltration considering hydrodynamic conditions in sewer systems.

PubMed

Karpf, Christian; Hoeft, Stefan; Scheffer, Claudia; Fuchs, Lothar; Krebs, Peter

2011-01-01

Sewer systems are closely interlinked with groundwater and surface water. Due to leaks and regular openings in the sewer system (e.g. combined sewer overflow structures with sometimes reverse pressure conditions), groundwater infiltration and surface water inflow as well as exfiltration of sewage take place and cannot be avoided. In the paper a new hydrodynamic sewer network modelling approach will be presented, which includes--besides precipitation--hydrographs of groundwater and surface water as essential boundary conditions. The concept of the modelling approach and the models to describe the infiltration, inflow and exfiltration fluxes are described. The model application to the sewerage system of the City of Dresden during a flood event with complex conditions shows that the processes of infiltration, exfiltration and surface water inflows can be described with a higher reliability and accuracy, showing that surface water inflow causes a pronounced system reaction. Further, according to the simulation results, a high sensitivity of exfiltration rates on the in-sewer water levels and a relatively low influence of the dynamic conditions on the infiltration rates were found.

Installing artificial macropores in degraded soils to enhance vertical infiltration and increase soil carbon content

NASA Astrophysics Data System (ADS)

Mori, Yasushi; Fujihara, Atsushi; Yamagishi, Kazuto

2014-12-01

Of all terrestrial media (including vegetation and the atmosphere), soil is the largest store of carbon. Soils also have important functions such as water storage and plant support roles. However, at present, these characteristics do not fully function, because of, for example, climate-change-induced heavy rainfall would wash away the organic-rich surface soils. In this study, artificial macropores were introduced into exposed soil plots for the purpose of enhancing infiltration, and fibrous material was inserted to reinforce the macropore structure. As expected, the capillary force caused by the fibers drew surface water deeper into the soil profile before saturation. Additionally, the same capillary force promoted vertical transport, while micropores (matrix) enhanced horizontal flow. Our results show that infiltration was more effective in the fiber-containing macropores than in empty macropores. Additionally, our column experiments showed that artificial macropores reduced surface runoff when the rainfall intensities were 2, 4, and 20 mm · h-1 but not for 80 mm · h-1. In field experiments, soil moisture sensors installed at depths of 10, 30, and 50 cm responded well to rainfall, showing that artificial macropores were able to successfully introduce surface water into the soil profile. One year after the artificial macropores were installed, a field survey carried out to assess soil organic matter and plant growth showed that plant biomass had doubled and that there was a significant increase in soil carbon. This novel technique has many advantages as it mimics natural processes, is low cost, and has a simple structure.

Using the natural biodegradation potential of shallow soils for in-situ remediation of deep vadose zone and groundwater.

PubMed

Avishai, Lior; Siebner, Hagar; Dahan, Ofer; Ronen, Zeev

2017-02-15

In this study, we examined the ability of top soil to degrade perchlorate from infiltrating polluted groundwater under unsaturated conditions. Column experiments designed to simulate typical remediation operation of daily wetting and draining cycles of contaminated water amended with an electron donor. Covering the infiltration area with bentonite ensured anaerobic conditions. The soil remained unsaturated, and redox potential dropped to less than -200mV. Perchlorate was reduced continuously from ∼1150mg/L at the inlet to ∼300mg/L at the outlet in daily cycles. Removal efficiency was between 60 and 84%. No signs of bioclogging were observed during three operation months although occasional iron reduction observed due to excess electron donor. Changes in perchlorate reducing bacteria numbers were inferred from an increased in pcrA gene abundances from ∼10 5 to 10 7 copied per gram at the end of the experiment indicating the growth of perchlorate-reducing bacteria. We proposed that the topsoil may serve as a bioreactor to treat high concentrations of perchlorate from the contaminated groundwater. The treated water that infiltrates from the topsoil through the vadose zone could be used to flush perchlorate from the deep vadose zone into the groundwater where it is retrieved again for treatment in the topsoil. Copyright © 2016 Elsevier B.V. All rights reserved.

A new method for indirectly estimating infiltration of paddy fields in situ

NASA Astrophysics Data System (ADS)

Xu, Yunqiang; Su, Baolin; Wang, Hongqi; He, Jingyi

2018-06-01

Infiltration is one of the major procedures in water balance research and pollution load estimation in paddy fields. In this study, a new method for indirectly estimating infiltration of paddy fields in situ was proposed and implemented in Taihu Lake basin. Since when there were no rainfall, irrigation and artificial drainage, the water depth variation process of a paddy field is only influenced by evapotranspiration and infiltration (E + F). Firstly, (E + F) was estimated by deciding the steady decreasing rate of water depth; then the evapotranspiration (ET) of the paddy field was calculated by using the crop coefficient method with the recommended FAO-56 Penman-Monteith equation; finally, the infiltration of the paddy field was obtained by subtracting ET from (E + F). Results show that the mean infiltration of the studied paddy field during rice jointing-booting period was 7.41 mm day-1, and the mean vertical infiltration and lateral seepage of the paddy field were 5.46 and 1.95 mm day-1 respectively.

18 CFR 430.13 - Protected area permits for new withdrawals.

Code of Federal Regulations, 2012 CFR

2012-04-01

... approved by the Commission. (3) A program to monitor and control ground water infiltration to the receiving sewer system. The program must quantify ground water infiltration to the system and document reductions in infiltration. The program should include such measures as leakage surveys of sewer mains, metering...

Thematic issue on soil water infiltration

USDA-ARS?s Scientific Manuscript database

Infiltration is the term applied to the process of water entry into the soil, generally by downward flow through all or part of the soil surface. Understanding of infiltration concept and processes has greatly improved, over the past 30 years, and new insights have been given into modeling of non-un...

18 CFR 430.13 - Protected area permits for new withdrawals.

Code of Federal Regulations, 2014 CFR

2014-04-01

... approved by the Commission. (3) A program to monitor and control ground water infiltration to the receiving sewer system. The program must quantify ground water infiltration to the system and document reductions in infiltration. The program should include such measures as leakage surveys of sewer mains, metering...

18 CFR 430.13 - Protected area permits for new withdrawals.

Code of Federal Regulations, 2013 CFR

2013-04-01

... approved by the Commission. (3) A program to monitor and control ground water infiltration to the receiving sewer system. The program must quantify ground water infiltration to the system and document reductions in infiltration. The program should include such measures as leakage surveys of sewer mains, metering...

18 CFR 430.13 - Protected area permits for new withdrawals.

Code of Federal Regulations, 2011 CFR

2011-04-01

... approved by the Commission. (3) A program to monitor and control ground water infiltration to the receiving sewer system. The program must quantify ground water infiltration to the system and document reductions in infiltration. The program should include such measures as leakage surveys of sewer mains, metering...

Variably-saturated groundwater modeling for optimizing managed aquifer recharge using trench infiltration

USGS Publications Warehouse

Heilweil, Victor M.; Benoit, Jerome; Healy, Richard W.

2015-01-01

Spreading-basin methods have resulted in more than 130 million cubic meters of recharge to the unconfined Navajo Sandstone of southern Utah in the past decade, but infiltration rates have slowed in recent years because of reduced hydraulic gradients and clogging. Trench infiltration is a promising alternative technique for increasing recharge and minimizing evaporation. This paper uses a variably saturated flow model to further investigate the relative importance of the following variables on rates of trench infiltration to unconfined aquifers: saturated hydraulic conductivity, trench spacing and dimensions, initial water-table depth, alternate wet/dry periods, and number of parallel trenches. Modeling results showed (1) increased infiltration with higher hydraulic conductivity, deeper initial water tables, and larger spacing between parallel trenches, (2) deeper or wider trenches do not substantially increase infiltration, (3) alternating wet/dry periods result in less overall infiltration than keeping the trenches continuously full, and (4) larger numbers of parallel trenches within a fixed area increases infiltration but with a diminishing effect as trench spacing becomes tighter. An empirical equation for estimating expected trench infiltration rates as a function of hydraulic conductivity and initial water-table depth was derived and can be used for evaluating feasibility of trench infiltration in other hydrogeologic settings

Effect of soil disturbance on recharging fluxes: Case study on the Snake River Plain, Idaho National Laboratory, USA

USGS Publications Warehouse

Nimmo, J.R.; Perkins, K.S.

2008-01-01

Soil structural disturbance influences the downward flow of water that percolates deep enough to become aquifer recharge. Data from identical experiments in an undisturbed silt-loam soil and in an adjacent simulated waste trench composed of the same soil material, but disturbed, included (1) laboratory- and field-measured unsaturated hydraulic properties and (2) field-measured transient water content profiles through 24 h of ponded infiltration and 75 d of redistribution. In undisturbed soil, wetting fronts were highly diffuse above 2 m depth, and did not go much deeper than 2 m. Darcian analysis suggests an average recharge rate less than 2 mm/year. In disturbed soil, wetting fronts were sharp and initial infiltration slower; water moved slowly below 2 m without obvious impediment. Richards' equation simulations with realistic conditions predicted sharp wetting fronts, as observed for disturbed soil. Such simulations were adequate for undisturbed soil only if started from a post-initial moisture distribution that included about 3 h of infiltration. These late-started simulations remained good, however, through the 76 d of data. Overall results suggest the net effect of soil disturbance, although it reduces preferential flow, may be to increase recharge by disrupting layer contrasts. ?? Springer-Verlag 2007.

Construction and performance of a long-term earthen liner experiment

USGS Publications Warehouse

Cartwright, Keros; Krapac, Ivan G.; Bonaparte, Rudolph

1990-01-01

In land burial schemes, compacted soil barriers with low hydraulic conductivity are commonly used in cover and liner systems to control the movement of liquids and prevent groundwater contamination. An experimental liner measuring 8 x 15 x 0.9 m was constructed with design criteria and equipment to simulate construction of soil liners built at waste disposal facilities. The surface of the liner was flooded with a 29.5 cm deep pond on April 12, 1988. Infiltration of water into the liner has been monitored for two years using 4 large-ring (1.5 m OD) and 32 small-ring (0.28 m OD) infiltrometers, and a water-balance that accounts for total infiltration and evaporation. Average long-term infiltration fluxes based on two years of monitoring are 5.8 x 10-9 cm/s, 6.0 x 10-8 cm/s and 5.6 x 10-8 for the large-ring, small-ring, and water-balance data, respectively. The saturated hydraulic conductivity of the liner based on small-ring data, estimated using Darcy's Law and the Green-Ampt Approximation, is 3 x 10-8 and 4 x 10-8 cm/s, respectively. All sets of data indicate that the liner's performance exceed that which is required by the U.S. EPA.

Artificial groundwater recharge as integral part of a water resources system in a humid environment

NASA Astrophysics Data System (ADS)

Kupfersberger, Hans; Stadler, Hermann

2010-05-01

In Graz, Austria, artificial groundwater recharge has been operated as an integral part of the drinking water supply system for more than thirty years. About 180 l/s of high quality water from pristine creeks (i.e. no pre-treatment necessary) are infiltrated via sand and lawn basins and infiltration trenches into two phreatic aquifers to sustain the extraction of approximately 400 l/s. The remaining third of drinking water for roughly 300.000 people is provided by a remote supply line from the East alpine karst region Hochschwab. By this threefold model the water supply system is less vulnerable to external conditions. In the early 1980's the infiltration devices were also designed as a hydraulic barrier against riverbank infiltration from the river Mur, which at that time showed seriously impaired water quality due to upstream paper mills. This resulted into high iron and manganese groundwater concentrations which lead to clogging of the pumping wells. These problems have been eliminated in the meantime due to the onsite purification of paper mill effluents and the construction of many waste water treatment plants. The recharge system has recently been thoroughly examined to optimize the operation of groundwater recharge and to provide a basis for further extension. The investigations included (i) field experiments and laboratory analyses to improve the trade off between infiltration rate and elimination capacities of the sand filter basins' top layer, (ii) numerical groundwater modelling to compute the recovery rate of the recharged water, the composition of the origin of the pumped water, emergency scenarios due to the failure of system parts, the transient capture zones of the withdrawal wells and the coordination of recharge and withdrawal and (iii) development of an online monitoring setup combined with a decision support system to guarantee reliable functioning of the entire structure. Additionally, the depreciation, maintenance and operation costs of the managed aquifer recharge system have been evaluated. Among numerous results it could be shown that replacing the lawn by sand basins and operating them constantly during winter holds the largest potential to increase the infiltration volume. However, this is only an option for new to build structures since the current basin positions would lead to large direct losses of recharged groundwater into the river Mur. Adjusting the timing of infiltration and withdrawal based on subsurface travel time yields an increase of the pumped amount of about 11% given about the same extension the wells' capture zones. The overall costs of artificial groundwater recharge amount to 0,15 €/m³ excluding pumping and distribution costs compared to a water price of about 1,5 €/m³ charged to consumers. Currently, the implications of building a hydro power plant adjacent to the recharge site are evaluated emphasizing the need for innovative solutions given only limited land resources. On the basis of the projected impacts of climate change on the availability of surface water and groundwater in the South-Eastern alpine regions, the aquifers can act as a buffer system to help overcome the timely shift between supply and demand. Thus, also in predominantly humid regions artificial groundwater recharge represents a viable and sustainable solution to safeguard the supply of drinking water in the long term.

[Soil infiltration of snowmelt water in the southern Gurbantunggut Desert, Xinjiang, China].

PubMed

Hu, Shun-jun; Chen, Yong-bao; Zhu, Hai

2015-04-01

Soil infiltration of snow-melt water is an important income item of water balance in arid desert. The soil water content in west slope, east slope and interdune of sand dune in the southern Gurbantunggut Desert was monitored before snowfall and after snow melting during the winters of 2012-2013 and 2013-2014. According to the principle of water balance, soil infiltration of snow-melt in the west slope, east slope, interdune and landscape scale was calculated, and compared with the results measured by cylinder method. The results showed that the soil moisture recharge from unfrozen layer of unsaturated soil to surface frozen soil was negligible because the soil moisture content before snowfall was lower, soil infiltration of snow-melt water was the main source of soil water of shallow soil, phreatic water did not evaporate during freezing period, and did not get recharge after the snow melting. Snowmelt water in the west slope, east slope, interdune and landscape scale were 20-43, 27-43, 32-45, 26-45 mm, respectively.

Accounting for Hydrologic State in Ground-Penetrating Radar Classification Systems

DTIC Science & Technology

2014-04-22

water content as a result of infiltration processes. • Demonstrated that effective medium approximations (one-dimensional flow and ray theory...280 290 300 310 320 330 340 -5 0 5 10 15 20 (a) (b) (c) Page 8 of 32 Figure 6: a) Conceptual model of flow experiment and GPR rays showing... ray theory for GPR) for characterizing the hydrologic state of the subsurface under arbitrary water content conditions. Figure 7: Comparison of

Numerical results on the contribution of an earthworm hole to infiltration

NASA Astrophysics Data System (ADS)

Pezzotti, Dario; Barontini, Stefano; Casali, Federico; Comincini, Mattia; Peli, Marco; Ranzi, Roberto; Rizzo, Gabriele; Tomirotti, Massimo; Vitale, Paolo

2017-04-01

On 9 March 2016 the WormEx I experiment was launched at the experimental site of Cividate Camuno (274ma.s.l., Oglio river basin, Central Italian Alps), aiming at contributing to understand how the soil-fauna digging activity affects soil-water flow. Particularly the experiment investigates the effects of earthworms holes on the soil-water constitutive laws, in the uppermost layers of a shallow anthropized soil. In this framework a set of simulations of the water flow in presence of an earthworm hole was preliminarily performed. The FV-FD numerical code AdHydra was used to solve the Richards equation in an axis-symmetric 2D domain around a vertical earthworm hole. The hole was represented both as a void cylinder and as a virtual porous domain with typical constitutive laws of a Δ-soil. The hypothesis of Poiseuille flow and the Jourin-Borelli law applied to determine its conductivity and soil-water retention relationship. Different scenarios of hole depth and infiltration rate were explored. As a result a meaningful change in the downflow condition was observed when burrows intersect a layered soil, both in saturated and partially unsaturated soils, in case a perched water table onsets at the interface between an upper and more conductive soil layer and a lower and less conductive one. These results may contribute to a better understanding of the streamflow generation processes and soil-water movement in shallow layered soils.

Effect of Post-Infiltration Soil Aeration at Different Growth Stages on Growth and Fruit Quality of Drip-Irrigated Potted Tomato Plants (Solanum lycopersicum)

PubMed Central

Li, Yuan; Jia, Zongxia; Niu, Wenquan; Wang, Jingwei; Zhang, Mingzhi

2015-01-01

Soil hydraulic principles suggest that post-infiltration hypoxic conditions would be induced in the plant root-zone for drip-irrigated tomato production in small pots filled with natural soil. No previous study specifically examined the response of tomato plants (Solanum lycopersicum) at different growth stages to low soil aeration under these conditions. A 2 × 6 factorial experiment was conducted to quantify effects of no post-infiltration soil aeration versus aeration during 5 different periods (namely 27–33, 34–57, 58–85, 86–99, and 27–99 days after sowing), on growth and fruit quality of potted single tomato plants that were sub-surface trickle-irrigated every 2 days at 2 levels. Soil was aerated by injecting 2.5 liters of air into each pot through the drip tubing immediately after irrigation. Results showed that post-infiltration aeration, especially during the fruit setting (34–57 DAS) and enlargement (58–85 DAS) growth stages, can positively influence the yield, root dry weight and activity, and the nutritional (soluble solids and vitamin C content), taste (titratable acidity), and market quality (shape and firmness) of the tomato fruits. Interactions between irrigation level and post-infiltration aeration on some of these fruit quality parameters indicated a need for further study on the dynamic interplay of air and water in the root zone of the plants under the conditions of this experiment. PMID:26630675

Effect of Post-Infiltration Soil Aeration at Different Growth Stages on Growth and Fruit Quality of Drip-Irrigated Potted Tomato Plants (Solanum lycopersicum).

PubMed

Li, Yuan; Jia, Zongxia; Niu, Wenquan; Wang, Jingwei; Zhang, Mingzhi

2015-01-01

Soil hydraulic principles suggest that post-infiltration hypoxic conditions would be induced in the plant root-zone for drip-irrigated tomato production in small pots filled with natural soil. No previous study specifically examined the response of tomato plants (Solanum lycopersicum) at different growth stages to low soil aeration under these conditions. A 2 × 6 factorial experiment was conducted to quantify effects of no post-infiltration soil aeration versus aeration during 5 different periods (namely 27-33, 34-57, 58-85, 86-99, and 27-99 days after sowing), on growth and fruit quality of potted single tomato plants that were sub-surface trickle-irrigated every 2 days at 2 levels. Soil was aerated by injecting 2.5 liters of air into each pot through the drip tubing immediately after irrigation. Results showed that post-infiltration aeration, especially during the fruit setting (34-57 DAS) and enlargement (58-85 DAS) growth stages, can positively influence the yield, root dry weight and activity, and the nutritional (soluble solids and vitamin C content), taste (titratable acidity), and market quality (shape and firmness) of the tomato fruits. Interactions between irrigation level and post-infiltration aeration on some of these fruit quality parameters indicated a need for further study on the dynamic interplay of air and water in the root zone of the plants under the conditions of this experiment.

Selected techniques for monitoring water movement through unsaturated alluvium during managed aquifer recharge

USGS Publications Warehouse

Nawikas, Joseph M.; O'Leary, David R.; Izbicki, John A.; Burgess, Matthew K.

2016-10-21

Managed aquifer recharge is used to augment natural recharge to aquifers. It can be used to replenish aquifers depleted by pumping or to store water during wetter years for withdrawal during drier years. Infiltration from ponds is a commonly used, inexpensive approach for managed aquifer recharge.At some managed aquifer-recharge sites, the time when infiltrated water arrives at the water table is not always clearly shown by water-level data. As part of site characterization and operation, it can be desirable to track downward movement of infiltrated water through the unsaturated zone to identify when it arrives at the water table.

Issues in the inverse modeling of a soil infiltration process

NASA Astrophysics Data System (ADS)

Kuraz, Michal; Jacka, Lukas; Leps, Matej

2017-04-01

This contribution addresses issues in evaluation of the soil hydraulic parameters (SHP) from the Richards equation based inverse model. The inverse model was representing single ring infiltration experiment on mountainous podzolic soil profile, and was searching for the SHP parameters of the top soil layer. Since the thickness of the top soil layer is often much lower than the depth required to embed the single ring or Guelph permeameter device, the SHPs for the top soil layer are very difficult to measure directly. The SHPs for the top soil layer were therefore identified here by inverse modeling of the single ring infiltration process, where, especially, the initial unsteady part of the experiment is expected to provide very useful data for evaluating the retention curve parameters (excluding the residual water content) and the saturated hydraulic conductivity. The main issue, which is addressed in this contribution, is the uniqueness of the Richards equation inverse model. We tried to answer the question whether is it possible to characterize the unsteady infiltration experiment with a unique set of SHPs values, and whether are all SHP parameters vulnerable with the non-uniqueness. Which is an important issue, since we could further conclude whether the popular gradient methods are appropriate here. Further the issues in assigning the initial and boundary condition setup, the influence of spatial and temporal discretization on the values of the identified SHPs, and the convergence issues with the Richards equation nonlinear operator during automatic calibration procedure are also covered here.

Methodology to assess water presence on speleothems during periods of low precipitation, with implications for recharge sources - Kartchner Caverns, Arizona

USGS Publications Warehouse

Blasch, Kyle W.

2011-01-01

Beginning in January 2005, recharge processes and the presence of water on speleothems were monitored in Kartchner Caverns during a 44-month period when annual rainfall rates were 6 to 18 percent below the long-term mean. Electrical-resistance sensors designed to detect the presence of water were used to identify ephemeral streamflow in the channels overlying the cave as well as the movement of water within the cave system. Direct infiltration of precipitation through overhead rocks provided consistent inflow to the cave, but precipitation rates and subsequent infiltration rates were reduced during the comparatively dry years. Ephemeral stream-channel recharge through autogenic and allogenic processes, the predominant recharge mechanism during wetter periods, was limited to two low-volume events. From visual observations, it appeared that recharge from channel infiltration was equal to or less than recharge from overhead infiltration. Electrical-resistance sensors were able to detect thin films of water on speleothems, including stalactites, ribbons, and stalagmites. These films of water were directly attributed to overhead infiltration of precipitation. Periods of low precipitation resulted in decreased speleothem wetness.

Infiltration in soils with a saturated surface

NASA Astrophysics Data System (ADS)

Hogarth, W. L.; Lockington, D. A.; Barry, D. A.; Parlange, M. B.; Haverkamp, R.; Parlange, J.-Y.

2013-05-01

An earlier infiltration equation relied on curve fitting of infiltration data for the determination of one of the parameters, which limits its usefulness in practice. This handicap is removed here, and the parameter is now evaluated by linking it directly to soil-water properties. The new predictions of infiltration using this evaluation are quite accurate. Positions and shapes of soil-water profiles are also examined in detail and found to be predicted analytically with great precision.

Long-term stormwater quantity and quality performance of permeable pavement systems.

PubMed

Brattebo, Benjamin O; Booth, Derek B

2003-11-01

This study examined the long-term effectiveness of permeable pavement as an alternative to traditional impervious asphalt pavement in a parking area. Four commercially available permeable pavement systems were evaluated after 6 years of daily parking usage for structural durability, ability to infiltrate precipitation, and impacts on infiltrate water quality. All four permeable pavement systems showed no major signs of wear. Virtually all rainwater infiltrated through the permeable pavements, with almost no surface runoff. The infiltrated water had significantly lower levels of copper and zinc than the direct surface runoff from the asphalt area. Motor oil was detected in 89% of samples from the asphalt runoff but not in any water sample infiltrated through the permeable pavement. Neither lead nor diesel fuel were detected in any sample. Infiltrate measured 5 years earlier displayed significantly higher concentrations of zinc and significantly lower concentrations of copper and lead.

40 CFR 440.144 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

...-cut mine plant site shall not exceed the volume of infiltration, drainage and mine drainage waters... of infiltration, drainage and mine drainage waters which is in excess of the make up water required...

40 CFR 440.144 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

...-cut mine plant site shall not exceed the volume of infiltration, drainage and mine drainage waters... of infiltration, drainage and mine drainage waters which is in excess of the make up water required...

Sequestration of Sr-90 Subsurface Contamination in the Hanford 100-N Area by Surface Infiltration of a Ca-Citrate-Phosphate Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szecsody, James E.; Rockhold, Mark L.; Oostrom, Martinus

The objective of this project is to develop a method to emplace apatite precipitate in the 100N vadose zone, which results in sorption and ultimately incorporation of Sr-90 into the apatite structure. The Ca-citrate-PO4 solution can be infiltrated into unsaturated sediments to result in apatite precipitate to provide effective treatment of Sr-90 contamination. Microbial redistribution during solution infiltration and a high rate of citrate biodegradation for river water microbes (water used for solution infiltration) results in a relatively even spatial distribution of the citrate biodegradation rate and ultimately apatite precipitate in the sediment. Manipulation of the Ca-citrate-PO4 solution infiltration strategymore » can be used to result in apatite precipitate in the lower half of the vadose zone (where most of the Sr-90 is located) and within low-K layers (which are hypothesized to have higher Sr-90 concentrations). The most effective infiltration strategy to precipitate apatite at depth (and with sufficient lateral spread) was to infiltrate a high concentration solution (6 mM Ca, 15 mM citrate, 60 mM PO4) at a rapid rate (near ponded conditions), followed by rapid, then slow water infiltration. Repeated infiltration events, with sufficient time between events to allow water drainage in the sediment profile can be used to buildup the mass of apatite precipitate at greater depth. Low-K heterogeneities were effectively treated, as the higher residual water content maintained in these zones resulted in higher apatite precipitate concentration. High-K zones did not receive sufficient treatment by infiltration, although an alternative strategy of air/surfactant (foam) was demonstrated effective for targeting high-K zones. The flow rate manipulation used in this study to treat specific depths and heterogeneities are not as easy to implement at field scale due to the lack of characterization of heterogeneities and difficulty tracking the wetting front over a large subsurface area. However, the use of real-time surface and cross-borehole geophysics can be used to track the infiltrating Ca-citrate-PO4 front so some adjustments can be made in the infiltration rate to precipitate apatite in desired zones. In addition, the reactive transport code used in this study with field scale physical parameters for sediments can be used to evaluate infiltration strategies along with preliminary water infiltration tests at field scale.« less

Impact of stormwater infiltration basins on groundwater quality, Perth metropolitan region, Western Australia

NASA Astrophysics Data System (ADS)

Appleyard, S. J.

1993-08-01

Twelve bores were sunk adjacent to three stormwater infiltration basins in the Perth metropolitan area to examine the impact of runoff from a light industrial area, a medium-density residential area, and a major arterial road on groundwater quality, and to examine the hydrological response of the aquifer to runoff recharge. Automatic and manual water level monitoring between April and November 1990 indicated that groundwater levels responded within minutes to recharge from the infiltration basins. Peak water levels of up to 2.5 m above rest levels occurred 6 24 h after the commencement of ponding in the infiltration basins. There was a marked reduction in salinity and increase in dissolved oxygen concentrations in the upper part of the aquifer downgradient of the infiltration basins. Concentrations of toxic metals, nutrients, pesticides, and phenolic compounds in groundwater near the infiltration basins were low and generally well within Australian drinking water guidelines. However, sediment in the base of an infiltration basin draining a major road contained in excess of 3500 ppm of lead. Phthalates, which are US EPA priority pollutants, were detected in all but one bore near the infiltration basins. Their detection may be a sampling artifact, but they may also be derived from the plastic litter that accumulates in the infiltration basins. The concentration of iron in groundwater near the infiltration basins appears to be controlled by dissolved oxygen concentrations, with high iron concentrations occurring where dissolved oxygen concentrations are low. Pumping bores located near infiltration basins may suffer from iron encrustation problems caused by the mixing of shallow, oxygenated groundwater with water containing higher concentrations of iron from deeper in the aquifer.

Evaluation of the potential for artificial ground-water recharge in eastern San Joaquin County, California; Phase 3

USGS Publications Warehouse

Hamlin, S.N.

1987-01-01

Infiltration tests were used to evaluate the potential of basin spreading surface water as a means of artificially recharging the aquifer system in eastern San Joaquin County, California. Two infiltration sites near Lockeford and Linden were selected on the basis of information collected during the first two phases of the study. Data from the infiltration tests indicate that the two sites are acceptable for recharge by the basin-spreading method. Infiltration rates ranged between 6.7 and 10.5 ft/day near Lockeford and between 2.6 and 11.2 ft/day near Linden. Interpretation of these data is limited by lack of information on the response of the saturated zone during testing and by the inherent difficulty in extrapolating the results of small-scale tests to larger long-term operations. Lithology is a major factor that controls infiltration rates at the test sites. The unsaturated zone is characterized by heterogeneous layers of coarse- and fine- grained materials. Clay layers of low hydraulic conductivity commonly form discontinuous lenses that may cause a transient perched water table to develop during recharge. Water level measurements from wells screened in the unsaturated zone indicate that the perched water table could reach the land surface after 2 and 5 months of recharge near Lockeford and Linden, respectively. These figures probably represent the minimum time necessary for saturation of the land. Another major factor that affects infiltration rates is the quality of the recharge water, particularly the suspended sediment content. The clogging action of suspended sediment may be minimized by: (1) pretreatment of recharge water in a settling pond, (2) adherence to a routine program of monitoring and maintenance, and (3) proper design of the recharge facility. Other factors that affect infiltration rates include basin excavation technique, basin shape, and maintenance procedures. Efficient operation of the recharge facility requires careful attention to the relation between subsurface water levels and infiltration rates. (Author 's abstract)

Biochars impact on water infiltration and water quality through a compacted subsoil layer.

PubMed

Novak, Jeff; Sigua, Gilbert; Watts, Don; Cantrell, Keri; Shumaker, Paul; Szogi, Ariel; Johnson, Mark G; Spokas, Kurt

2016-01-01

Soils in the SE USA Coastal Plain region frequently have a compacted subsoil layer (E horizon), which is a barrier for water infiltration. Four different biochars were evaluated to increase water infiltration through a compacted horizon from a Norfolk soil (fine-loamy, kaolinitic, thermic, Typic Kandiudult). In addition, we also evaluated biochars effect on water quality. Biochars were produced by pyrolysis at 500 °C from pine chips (Pinus taeda), poultry litter (Gallus domesticus) feedstocks, and as blends (50:50 and 80:20) of pine chip:poultry litter. Prior to pyrolysis, the feedstocks were pelletized and sieved to >2-mm pellets. Each biochar was mixed with the subsoil at 20 g/kg (w/w) and the mixture was placed in columns. The columns were leached four times with Milli-Q water over 128 d of incubation. Except for the biochar produced from poultry litter, all other applied biochars resulted in significant water infiltration increases (0.157-0.219 mL min(-1); p<0.05) compared to the control (0.095 mL min(-1)). However, water infiltration in each treatment were influenced by additional water leaching. Leachates were enriched in PO4, SO4, Cl, Na, and K after addition of poultry litter biochar, however, their concentrations declined in pine chip blended biochar treatments and after multiple leaching. Adding biochars (except 100% poultry litter biochar) to a compacted subsoil layer can initially improve water infiltration, but, additional leaching revealed that the effect remained only for the 50:50 pine chip:poultry litter blended biochar while it declined in other biochar treatments. Published by Elsevier Ltd.

Dynamics of flood water infiltration and ground water recharge in hyperarid desert.

PubMed

Dahan, Ofer; Tatarsky, Boaz; Enzel, Yehouda; Kulls, Christoph; Seely, Mary; Benito, Gererdo

2008-01-01

A study on flood water infiltration and ground water recharge of a shallow alluvial aquifer was conducted in the hyperarid section of the Kuiseb River, Namibia. The study site was selected to represent a typical desert ephemeral river. An instrumental setup allowed, for the first time, continuous monitoring of infiltration during a flood event through the channel bed and the entire vadose zone. The monitoring system included flexible time domain reflectometry probes that were designed to measure the temporal variation in vadose zone water content and instruments to concurrently measure the levels of flood and ground water. A sequence of five individual floods was monitored during the rainy season in early summer 2006. These newly generated data served to elucidate the dynamics of flood water infiltration. Each flood initiated an infiltration event which was expressed in wetting of the vadose zone followed by a measurable rise in the water table. The data enabled a direct calculation of the infiltration fluxes by various independent methods. The floods varied in their stages, peaks, and initial water contents. However, all floods produced very similar flux rates, suggesting that the recharge rates are less affected by the flood stages but rather controlled by flow duration and available aquifer storage under it. Large floods flood the stream channel terraces and promote the larger transmission losses. These, however, make only a negligible contribution to the recharge of the ground water. It is the flood duration within the active streambed, which may increase with flood magnitude that is important to the recharge process.

Physical and mathematical modeling of transient infiltration through shallow layered pyroclastic deposits

NASA Astrophysics Data System (ADS)

Damiano, Emilia; Greco, Roberto; Guida, Andrea; Olivares, Lucio; Picarelli, Luciano

2017-04-01

Layered pyroclastic deposits covering steep slopes, characteristic of large mountainous areas of Campania (southern Italy), are often affected by shallow landslides triggered by heavy rainfall events. In fact, the equilibrium of such deposits is usually guaranteed by the contribution to soil shear strength offered by soil suction, which decreases during wetting. As the return period of the triggering events has been in many cases not extreme, other factors concur to establish triggering conditions. In this respect, heterogeneities, strongly affecting transient infiltration, may in some cases play a crucial role. In this study, the effect of the presence of soil layers, characterized by markedly different hydraulic properties, on the rainwater infiltration process is investigated. In fact, the pyroclastic covers of Campania, being the result of the deposition of materials originated by several eruptions of the nearby volcanic complexes, usually consist of alternating layers of ashes (silty sands) and pumices (gravel with sand). The presence of coarse-textured pumices between finer ashes strongly affects the infiltration process. In fact, the pumices, which are characterized by saturated hydraulic conductivity larger than ashes, are capable of retaining less water than ashes in unsaturated conditions, so that their unsaturated hydraulic conductivity is usually very small. Hence, depending on the water potential distribution throughout the cover at the onset of rainfall, pumices may act as a barrier to the propagation of the wet front (the so-called capillary barrier effect), or, approaching saturation, let the water pass through them very quickly. Such a complex behavior has been studied by means of a series of infiltration experiments carried out in an instrumented flume in the Geotechnical Laboratory of the University of Campania (http://www.dicdea.unina2.it/it/dipartimento/laboratori/laboratorio-di-geotecnica). Starting from different initial moisture conditions, small scale physical models of layered slopes, with various geometry and inclination, have been subjected to rainfalls of various intensities. During the infiltration processes and the following water redistribution phases, soil moisture and matric potential have been measured at various locations by means of TDR probes and tensiometers, respectively. The interpretation of the experimental results has been aided by a 2D mathematical model based on the integration of Richards' equation with the finite differences method. The obtained results indicate that a layer of dry pumices may induce lateral redistribution of water through the overlying ashes. In steep sloping deposits, this may favor the establishment of downslope directed subsurface runoff, which drains part of the infiltrating water towards the toe of the slope. In real slopes, depending on local morphology, such a downslope flow may have a beneficial effect on slope stability, as some water is drained out of the slope, or may even contribute to the establishment of triggering conditions, as it can result in flow concentration leading to local failure.

Seasonal Variation of Infiltration Rates in a Managed Aquifer Recharge System: A Belgian Example

NASA Astrophysics Data System (ADS)

Samanta, S.; Sheng, Z.; Munster, C. L.; Houtte, E. V.

2017-12-01

Managed Aquifer Recharge (MAR) is a powerful tool in addressing water resources management issues. The Torreele water reuse facility is using MAR to address the problem of water sustainability in a coastal aquifer of Belgium. The Torreele MAR facility uses infiltration ponds to maintain the groundwater level and to prevent saltwater intrusion into the aquifer. The source of recharge is treated wastewater from the Torreele wastewater treatment plant (TWWTP) located 1.2 km inland. The TWWTP uses a state-of-the-art filtration mechanism with a combination of ultrafiltration (UF) and Reverse Osmosis (RO) techniques to assure that recharge water is of very high quality. Data collected at the Torreele MAR facility indicates reduced infiltration rates during the winter season when pond water temperatures vary from 1 to 10ºC. The proposed hypothesis for these lower infiltration rates may be a reduction in hydraulic conductivity due to changes in water viscosity. This study involves the determination of relationship between water temperature, infiltration rates, and hydraulic conductivity at the Torreele MAR facility. The results of this study will lead to an effective administration of the facility and provide an extensive understanding of the system.

24 CFR 3280.307 - Resistance to elements and use.

Code of Federal Regulations, 2010 CFR

2010-04-01

... shall be designed, and assembled to protect against the infiltration of air and water, except for any... infiltration of air or water. (c) Where adjoining materials or assemblies of materials are of such nature that... transportation, sealants shall be of a type that maintains protection against infiltration or penetration by air...

24 CFR 3280.307 - Resistance to elements and use.

Code of Federal Regulations, 2013 CFR

2013-04-01

... shall be designed, and assembled to protect against the infiltration of air and water, except for any... infiltration of air or water. (c) Where adjoining materials or assemblies of materials are of such nature that... transportation, sealants shall be of a type that maintains protection against infiltration or penetration by air...

24 CFR 3280.307 - Resistance to elements and use.

Code of Federal Regulations, 2011 CFR

2011-04-01

... shall be designed, and assembled to protect against the infiltration of air and water, except for any... infiltration of air or water. (c) Where adjoining materials or assemblies of materials are of such nature that... transportation, sealants shall be of a type that maintains protection against infiltration or penetration by air...

24 CFR 3280.307 - Resistance to elements and use.

Code of Federal Regulations, 2012 CFR

2012-04-01

... shall be designed, and assembled to protect against the infiltration of air and water, except for any... infiltration of air or water. (c) Where adjoining materials or assemblies of materials are of such nature that... transportation, sealants shall be of a type that maintains protection against infiltration or penetration by air...

24 CFR 3280.307 - Resistance to elements and use.

Code of Federal Regulations, 2014 CFR

2014-04-01

... shall be designed, and assembled to protect against the infiltration of air and water, except for any... infiltration of air or water. (c) Where adjoining materials or assemblies of materials are of such nature that... transportation, sealants shall be of a type that maintains protection against infiltration or penetration by air...

Natural water purification and water management by artificial groundwater recharge

PubMed Central

Balke, Klaus-Dieter; Zhu, Yan

2008-01-01

Worldwide, several regions suffer from water scarcity and contamination. The infiltration and subsurface storage of rain and river water can reduce water stress. Artificial groundwater recharge, possibly combined with bank filtration, plant purification and/or the use of subsurface dams and artificial aquifers, is especially advantageous in areas where layers of gravel and sand exist below the earth’s surface. Artificial infiltration of surface water into the uppermost aquifer has qualitative and quantitative advantages. The contamination of infiltrated river water will be reduced by natural attenuation. Clay minerals, iron hydroxide and humic matter as well as microorganisms located in the subsurface have high decontamination capacities. By this, a final water treatment, if necessary, becomes much easier and cheaper. The quantitative effect concerns the seasonally changing river discharge that influences the possibility of water extraction for drinking water purposes. Such changes can be equalised by seasonally adapted infiltration/extraction of water in/out of the aquifer according to the river discharge and the water need. This method enables a continuous water supply over the whole year. Generally, artificially recharged groundwater is better protected against pollution than surface water, and the delimitation of water protection zones makes it even more save. PMID:18357624

Natural water purification and water management by artificial groundwater recharge.

PubMed

Balke, Klaus-Dieter; Zhu, Yan

2008-03-01

Worldwide, several regions suffer from water scarcity and contamination. The infiltration and subsurface storage of rain and river water can reduce water stress. Artificial groundwater recharge, possibly combined with bank filtration, plant purification and/or the use of subsurface dams and artificial aquifers, is especially advantageous in areas where layers of gravel and sand exist below the earth's surface. Artificial infiltration of surface water into the uppermost aquifer has qualitative and quantitative advantages. The contamination of infiltrated river water will be reduced by natural attenuation. Clay minerals, iron hydroxide and humic matter as well as microorganisms located in the subsurface have high decontamination capacities. By this, a final water treatment, if necessary, becomes much easier and cheaper. The quantitative effect concerns the seasonally changing river discharge that influences the possibility of water extraction for drinking water purposes. Such changes can be equalised by seasonally adapted infiltration/extraction of water in/out of the aquifer according to the river discharge and the water need. This method enables a continuous water supply over the whole year. Generally, artificially recharged groundwater is better protected against pollution than surface water, and the delimitation of water protection zones makes it even more save.

Estimated infiltration, percolation, and recharge rates at the Rillito Creek focused recharge investigation site, Pima County, Arizona: Chapter H in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Hoffmann, John P.; Blasch, Kyle W.; Pool, Don R.; Bailey, Matthew A.; Callegary, James B.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

A large fraction of ground water stored in the alluvial aquifers in the Southwest is recharged by water that percolates through ephemeral stream-channel deposits. The amount of water currently recharging many of these aquifers is insufficient to meet current and future demands. Improving the understanding of streambed infiltration and the subsequent redistribution of water within the unsaturated zone is fundamental to quantifying and forming an accurate description of streambed recharge. In addition, improved estimates of recharge from ephemeral-stream channels will reduce uncertainties in water-budget components used in current ground-water models.This chapter presents a summary of findings related to a focused recharge investigation along Rillito Creek in Tucson, Arizona. A variety of approaches used to estimate infiltration, percolation, and recharge fluxes are presented that provide a wide range of temporal- and spatial-scale measurements of recharge beneath Rillito Creek. The approaches discussed include analyses of (1) cores and cuttings for hydraulic and textural properties, (2) environmental tracers from the water extracted from the cores and cuttings, (3) seepage measurements made during sustained streamflow, (4) heat as a tracer and numerical simulations of the movement of heat through the streambed sediments, (5) water-content variations, (6) water-level responses to streamflow in piezometers within the stream channel, and (7) gravity changes in response to recharge events. Hydraulic properties of the materials underlying Rillito Creek were used to estimate long-term potential recharge rates. Seepage measurements and analyses of temperature and water content were used to estimate infiltration rates, and environmental tracers were used to estimate percolation rates through the thick unsaturated zone. The presence or lack of tritium in the water was used to determine whether or not water in the unsaturated zone infiltrated within the past 40 years. Analysis of water-level and temporal-gravity data were used to estimate recharge volumes. Data presented in this chapter were collected from 1999 though 2002. Precipitation and streamflow during this period were less than the long-term average; however, two periods of significant streamflow resulted in recharge—one in the summer of 1999 and the other in the fall/winter of 2000.Flux estimates of infiltration and recharge vary from less than 0.1 to 1.0 cubic meter per second per kilometer of streamflow. Recharge-flux estimates are larger than infiltration estimates. Larger recharge fluxes than infiltration fluxes are explained by the scale of measurements. Methods used to estimate recharge rates incorporate the largest volumetric and temporal scales and are likely to have fluxes from other nearby sources, such as unmeasured tributaries, whereas the methods used to estimate infiltration incorporate the smallest scales, reflecting infiltration rates at individual measurement sites.

Ground-water flow and numerical simulation of recharge from streamflow infiltration near Pine Nut Creek, Douglas County, Nevada

USGS Publications Warehouse

Maurer, Douglas K.

2002-01-01

Ground-water flow and recharge from infiltration near Pine Nut Creek, east of Gardnerville, Nevada, were simulated using a single-layer numerical finite-difference model as part of a study made by the U.S. Geological Survey in cooperation with the Carson Water Subconservancy District. The model was calibrated to 190 water-level measurements made in 27 wells in December 2000, and in 9 wells from August 1999 through April 2001. The purpose of this study was to estimate reasonable limits for the approximate volume of water that may be stored by recharge through infiltration basins, and the rate at which recharged water would dissipate or move towards the valley floor. Measured water levels in the study area show that infiltration from the Allerman Canal and reservoir has created a water-table mound beneath them that decreases the hydraulic gradient east of the canal and increases the gradient west of the canal. North of Pine Nut Creek, the mound causes ground water to flow toward the northern end of the reservoir. South of Pine Nut Creek, relatively high water levels probably are maintained by the mound beneath the Allerman Canal and possibly by greater rates of recharge from the southeast. Water-level declines near Pine Nut Creek from August 1999 through April 2001 probably are caused by dissipation of recharge from infiltration of Pine Nut Creek streamflow in the springs of 1998 and 1999. Using the calibrated model, a simulation of recharge through a hypothetical infiltration basin covering 12.4 acres near Pine Nut Creek applied 700 acre-feet per year of recharge over a six-month period, for a total of 3,500 acre-feet after 5 consecutive years. This recharge requires a diversion rate of about 2 cubic feet per second and an infiltration rate of 0.3 foot per day. The simulations showed that recharge of 3,500 acre-feet caused water levels near the basin to rise over 70 feet, approaching land surface, indicating 3,500 acre-feet is the maximum that may be stored in a 5-year period, given the basin location and surface area used in the simulations. Greater amounts probably could be stored if separate infiltration basins were installed at different locations along the Pine Nut Creek alluvial fan, applying the recharge over a larger area. The water-table mound resulting from recharge extended 7,000 feet north, west, and south of the infiltration basin. After recharge ceased, water levels near the center of the mound declined rapidly to within 20 feet of initial levels after 2 years, and within 10 feet of initial levels after 7 years. The recharge mound dissipates laterally across the modeled area at decreasing rates over time. A water-level rise of 1 foot moved westward towards the valley floor 660 feet from peak conditions after 1 year, and averaged 550 feet, 440 feet, and 330 feet per year for the periods 1-4, 4-7, and 7-10 years, respectively, after recharge ceased. Simulations of subsequent pumping from hypothetical wells near the infiltration basin were made by applying pumping near the basin beginning 1 year after recharge of 3,500 acre-feet ceased. Pumping was applied over a 6-month period for 4 years from one well at 400 acre-feet per year, withdrawing 1,600 acre-feet or 45 percent of that recharged, and from two wells totaling 800 acre-feet per year, withdrawing 3,200 acre-feet or 90 percent of that recharged. Pumping of 1,600 acre-feet caused water-levels near the infiltration basin to decline only slightly below initial levels. Pumping of 3,200 acre-feet caused water-levels near the infiltration basin to decline a maximum of 30 feet below initial levels, with smaller declines extending laterally in all directions for 4,000 feet from the pumping wells. Water-level declines are a result of pumping at a rate sufficient to withdraw the majority of the water recharged through the infiltration basin. Although the declines may affect water levels in nearby domestic wells, the simulations show that water levels recover quickly after

44 CFR 60.3 - Flood plain management criteria for flood-prone areas.

Code of Federal Regulations, 2012 CFR

2012-10-01

... minimize or eliminate infiltration of flood waters into the systems; and (6) Require within flood-prone... infiltration of flood waters into the systems and discharges from the systems into flood waters and (ii) onsite...

44 CFR 60.3 - Flood plain management criteria for flood-prone areas.

Code of Federal Regulations, 2014 CFR

2014-10-01

... minimize or eliminate infiltration of flood waters into the systems; and (6) Require within flood-prone... infiltration of flood waters into the systems and discharges from the systems into flood waters and (ii) onsite...

44 CFR 60.3 - Flood plain management criteria for flood-prone areas.

Code of Federal Regulations, 2013 CFR

2013-10-01

... minimize or eliminate infiltration of flood waters into the systems; and (6) Require within flood-prone... infiltration of flood waters into the systems and discharges from the systems into flood waters and (ii) onsite...

Hydro-mechanical mechanism and thresholds of rainfall-induced unsaturated landslides

NASA Astrophysics Data System (ADS)

Yang, Zongji; Lei, Xiaoqin; Huang, Dong; Qiao, Jianping

2017-04-01

The devastating Ms 8 Wenchuan earthquake in 2008 created the greatest number of co-seismic mountain hazards ever recorded in China. However, the dynamics of rainfall induced mass remobilization and transport deposits after giant earthquake are not fully understood. Moreover, rainfall intensity and duration (I-D) methods are the predominant early warning indicators of rainfall-induced landslides in post-earthquake region, which are a convenient and straight-forward way to predict the hazards. However, the rainfall-based criteria and thresholds are generally empirical and based on statistical analysis,consequently, they ignore the failure mechanisms of the landslides. This study examines the mechanism and hydro-mechanical behavior and thresholds of these unsaturated deposits under the influence of rainfall. To accomplish this, in situ experiments were performed in an instrumented landslide deposit, The field experimental tests were conducted on a natural co-seismic fractured slope to 1) simulate rainfall-induced shallow failures in the depression channels of a debris flow catchment in an earthquake-affected region, 2)explore the mechanisms and transient processes associated with hydro-mechanical parameter variations in response to the infiltration of rainfall, and 3) identify the hydrologic parameter thresholds and critical criteria of gravitational erosion in areas prone to mass remobilization as a source of debris flows. These experiments provided instrumental evidence and directly proved that post-earthquake rainfall-induced mass remobilization occurred under unsaturated conditions in response to transient rainfall infiltration, and revealed the presence of transient processes and the dominance of preferential flow paths during rainfall infiltration. A hydro-mechanical method was adopted for the transient hydrologic process modelling and unsaturated slope stability analysis. and the slope failures during the experimental test were reproduced by the model, indicating that the decrease in matrix suction and increase in moisture content in response to rainfall infiltration contributed greatly to post-earthquake shallow mass movement. Thus, a threshold model for the initiation of mass remobilization is proposed based on correlations between slope stability and volumetric water content and matrix suction As a complement to rainfall-based early warning strategies, the water content and suction threshold models based on the water infiltration induced slope failure mechanism. the proposed method are expected to improve the accuracy of prediction and early warnings of post-earthquake mountain hazards

On the physics of unstable infiltration, seepage, and gravity drainage in partially saturated tuffs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faybishenko, B.; Bodvarsson, G.S.; Salve, R.

2002-04-01

To improve understanding of the physics of dynamic instabilities in unsaturated flow processes within the Paintbrush nonwelded unit (PTn) and the middle nonlithophysal portion of the Tonopah Spring welded tuff unit (TSw) of Yucca Mountain, we analyzed data from a series of infiltration tests carried out at two sites (Alcove 4 and Alcove 6) in the Exploratory Studies Facility, using analytical and empirical functions. The analysis of infiltration rates measured at both sites showed three temporal scales of infiltration rate: (1) a macro-scale trend of overall decreasing flow, (2) a meso-scale trend of fast and slow motion exhibiting three-stage variationsmore » of the flow rate (decreasing, increasing, and [again] decreasing flow rate, as observed in soils in the presence of entrapped air), and (3) micro-scale (high frequency) fluctuations. Infiltration tests in the nonwelded unit at Alcove 4 indicate that this unit may effectively dampen episodic fast infiltration events; however, well-known Kostyakov, Horton, and Philip equations do not satisfactorily describe the observed trends of the infiltration rate. Instead, a Weibull distribution model can most accurately describe experimentally determined time trends of the infiltration rate. Infiltration tests in highly permeable, fractured, welded tuff at Alcove 6 indicate that the infiltration rate exhibits pulsation, which may have been caused by multiple threshold effects and water-air redistribution between fractures and matrix. The empirical relationships between the extrinsic seepage from fractures, matrix imbibition, and gravity drainage versus the infiltration rate, as well as scaling and self-similarity for the leading edge of the water front are the hallmark of the nonlinear dynamic processes in water flow under episodic infiltration through fractured tuff. Based on the analysis of experimental data, we propose a conceptual model of a dynamic fracture flow and fracture-matrix interaction in fractured tuff, incorporating the time dependent processes of water redistribution in the fracture-matrix system.« less

An efficient and guaranteed stable numerical method for continuous modeling of infiltration and redistribution with a shallow dynamic water table

NASA Astrophysics Data System (ADS)

Lai, Wencong; Ogden, Fred L.; Steinke, Robert C.; Talbot, Cary A.

2015-03-01

We have developed a one-dimensional numerical method to simulate infiltration and redistribution in the presence of a shallow dynamic water table. This method builds upon the Green-Ampt infiltration with Redistribution (GAR) model and incorporates features from the Talbot-Ogden (T-O) infiltration and redistribution method in a discretized moisture content domain. The redistribution scheme is more physically meaningful than the capillary weighted redistribution scheme in the T-O method. Groundwater dynamics are considered in this new method instead of hydrostatic groundwater front. It is also computationally more efficient than the T-O method. Motion of water in the vadose zone due to infiltration, redistribution, and interactions with capillary groundwater are described by ordinary differential equations. Numerical solutions to these equations are computationally less expensive than solutions of the highly nonlinear Richards' (1931) partial differential equation. We present results from numerical tests on 11 soil types using multiple rain pulses with different boundary conditions, with and without a shallow water table and compare against the numerical solution of Richards' equation (RE). Results from the new method are in satisfactory agreement with RE solutions in term of ponding time, deponding time, infiltration rate, and cumulative infiltrated depth. The new method, which we call "GARTO" can be used as an alternative to the RE for 1-D coupled surface and groundwater models in general situations with homogeneous soils with dynamic water table. The GARTO method represents a significant advance in simulating groundwater surface water interactions because it very closely matches the RE solution while being computationally efficient, with guaranteed mass conservation, and no stability limitations that can affect RE solvers in the case of a near-surface water table.

Water fluxes in root-soil-systems investigated by Magnetic resonance imaging

NASA Astrophysics Data System (ADS)

Haber-Pohlmeier, Sabina; Javaux, Mathieu; Pohlmeier, Andreas

2010-05-01

Water flux through soils is one of the most important control function with respect to the water supply for root and plant growth. The understanding of these processes bases generally on the interplay between experimental investigations and the development of theory and numerical models. In recent time detailed 3D models have been developed, but experimental information is mainly available from two-dimensional rhizotrons or only with coarse resolution from water content measurements by means of TDR probes and tensiometers. An emerging powerful tool for high resolution, non-invasive imaging of water content and fluxes in soils in saturated and unsaturated state is Nuclear Magnetic Resonance Imaging (MRI)[1,2]. With respect to water fluxes the slow flow velocities do not allow the direct monitoring by MRI flow imaging so indirect methods like transport of contrast agents should be applied. Therefore we have chosen Gd-DTPA [3], a negatively charged paramagnetic Gd-complex, as tracer for the investigation of water fluxes during i) infiltration and ii) injection experiments of unsaturated model soil with maize and lupin plants. The contrast of the NMR measurements was optimised using high resolution T1 weighted spin echo sequences. With respect to the infiltration experiment we observed that during rapid infiltration from the bottom the plume moved homogeneously into the bulk soil, but leaves out the immediate surrounding of the maize roots. After this initial period a continuously increasing enrichment of tracer in this region is monitored, but no uptake by the plant within one hour. Continuing these studies injection experiments have been performed where the tracer was placed in a small volume in the direct vicinity of the roots, and the entire water content changed only minimal even under quite dry conditions. For a well developed lupin root system we observed diffusive spreading followed by a very slow transporte of the plume to the root system over a period of two days. The important difference to the short term experiment is the observation of tracer uptake followed by an upward transport in the inner root tissues. This could also be proved by a following chemical analysis showing decreasing Gd content from the roots over the shoot to the leaves. In parallel a high resolution 3d image of the root system architecture was performed, in order to compare the experimentally observed motion of the plume with detailed 3D model calculations of water uptake and tracer transport. References: 1. Pohlmeier, A., et al., Imaging water fluxes in porous media by magnetic resonance imaging using D2O as a tracer. Mag. Res. Imag., 2008. 27(2): p. 285-292. 2. Pohlmeier, A., et al., Changes in Soil Water Content Resulting from Ricinus Root Uptake Monitored by Magnetic Resonance Imaging Vadose Zone Journal, 2008. 7: p. 1010-1017. 3. Haber-Pohlmeier, S., Stapf S. and Pohlmeier A., Waterflow monitored by tracer transport in natural porouse media using MRI. Vadose Zone Journal, submitted

Assessment of Physical, Chemical, and Hydrologic Factors Affecting the Infiltration of Treated Wastewater in theNew Jersey Coastal Plain, with Emphasis on theHammonton Land Application Facility

USGS Publications Warehouse

Reilly, Timothy J.; Romanok, Kristin M.; Tessler, Steven; Fischer, Jeffrey M.

2010-01-01

A hydrogeologic and water-quality investigation of the Hammonton Land Application Facility (Hammonton LAF) in Hammonton, New Jersey, was conducted to determine the factors that impede the infiltration of treated wastewater and to assess the potential for similar conditions to exist elsewhere in the Coastal Plain of New Jersey (particularly within the Pinelands National Reserve). Gamma logs, sediment cores, and hydraulic-profile testing indicate that extensive fine-grained strata and iron-cemented sands underlying the Hammonton LAF may impede infiltration and lead to the perching of diluted treated wastewater. Perched water was observed in augured holes adjacent to infiltration trenches, and analysis of wastewater loading and infiltration data indicates that infiltration trenches may receive lateral flow from multiple perched-water sources. Analysis of water-quality properties characteristic of treated wastewater show that although infiltrated wastewater is reaching the underlying aquifer, lengthy holding times and a long recharge pathway greatly reduce the concentrations of nitrate, boron, and many organic compounds typical of wastewater. Conditions at two currently operating facilities and one potential future facility in the New Jersey Coastal Plain were compared to those at the Hammonton Land Application Facility (LAF). Facilities operating as designed are not underlain by the restrictive strata that exist at the Hammonton LAF. Careful characterization of the geology and hydrology of the unsaturated zone underlying infiltration structures of future facilities in the New Jersey Coastal Plain and similar hydrogeologic settings will help to avoid constructing infiltration structures over or within low-hydraulic-conductivity strata that will decrease infiltration rates.

The Perspective of Riverbank Filtration in China

NASA Astrophysics Data System (ADS)

Li, J.; Teng, Y.; Zhai, Y.; Zuo, R.

2014-12-01

Sustainable drinking water supply can affect the health of people, and the surrounding ecosystems. According to statistics of the monitoring program of drinking water sources in 309 at or above prefecture level of China in 2013, the major pollutants index were total phosphorus, ammonia and manganese in surface drinking water sources, respectively, iron, ammonia and manganese in groundwater drinking water sources, respectively. More than 150 drinking water emergency environmental accidents happened since 2006, 52 of these accidents led to the disruption of water supply in waterworks, and a population of over ten million were affected. It indicated that there is a potential risk for people's health by the use of river water directly and it is necessary to require alternative techniques such as riverbank filtration for improving the drinking water quality. Riverbank filtration is an inexpensive natural process, not only smoothing out normal pollutant concentration found in surface water but also significantly reducing the risk from such emergency events as chemical spill into the river. Riverbank filtration technique has been used in many countries more than 100 years, including China. In China, in 1950s, the bank infiltration technique was first applied in northeast of China. Extensive bank infiltration application was conducted in 1980s, and more than 300 drinking water sources utilities bank infiltration established mainly near the Songhua River Basin, the Yellow River Basin, Haihe River Basin. However, the comparative lack of application and researches on riverbank filtration have formed critical scientific data gap in China. As the performance of riverbank filtration technique depend on not only the design and setting such as well type, pumping rate, but also the local hydrogeology and environmental properties. We recommend more riverbank filtration project and studies to be conducted to collect related significant environmental geology data in China. Additionally, the experience has demonstrated a number of water quality improvements associated with riverbank filtration. It is important to stress that the fate and behavior of emerging organic contaminants during riverbank filtration should be taken into special consideration.

Identification of an urban fractured-rock aquifer dynamics using an evolutionary self-organizing modelling

NASA Astrophysics Data System (ADS)

Hong, Yoon-Seok; Rosen, Michael R.

2002-03-01

An urban fractured-rock aquifer system, where disposal of storm water is via 'soak holes' drilled directly into the top of fractured-rock basalt, has a highly dynamic nature where theories or knowledge to generate the model are still incomplete and insufficient. Therefore, formulating an accurate mechanistic model, usually based on first principles (physical and chemical laws, mass balance, and diffusion and transport, etc.), requires time- and money-consuming tasks. Instead of a human developing the mechanistic-based model, this paper presents an approach to automatic model evolution in genetic programming (GP) to model dynamic behaviour of groundwater level fluctuations affected by storm water infiltration. This GP evolves mathematical models automatically that have an understandable structure using function tree representation by methods of natural selection ('survival of the fittest') through genetic operators (reproduction, crossover, and mutation). The simulation results have shown that GP is not only capable of predicting the groundwater level fluctuation due to storm water infiltration but also provides insight into the dynamic behaviour of a partially known urban fractured-rock aquifer system by allowing knowledge extraction of the evolved models. Our results show that GP can work as a cost-effective modelling tool, enabling us to create prototype models quickly and inexpensively and assists us in developing accurate models in less time, even if we have limited experience and incomplete knowledge for an urban fractured-rock aquifer system affected by storm water infiltration.

An Induced Infiltration and Groundwater Transfer Project to Enhance Recharge in the Lower Mississippi River Valley Alluvial Aquifer: Modeling and Analysis

NASA Astrophysics Data System (ADS)

Rigby, J.; Haugh, C. J.; Barlow, J.

2015-12-01

The Lower Mississippi River Basin is one of the major agricultural production regions in the United States producing over two-thirds of the rice, nearly half of sugarcane produced in the U.S., as well as significant amounts of soybeans, corn, and cotton. While the region experiences over 50 inches of precipitation annually, reaching yield potential for crops requires irrigation. Approximately 75% of crop acres in the alluvial valley are irrigated, and the expectation is that all acreage will eventually be irrigated. Currently over 90% of water for crop irrigation is derived from the shallow alluvial aquifer outpacing net recharge by several million acre-feet per year. This has resulted in severe groundwater declines in Arkansas and an increasingly threatening situation in northwestern Mississippi. In Mississippi, direct injection has received increasing attention as a means of artificial recharge, though water quality remains a concern both for the integrity of the aquifer and efficiency of injection. This project considers the use of pumping wells near major rivers known to be in connection with the aquifer to induce additional infiltration of surface water by steepening local gradients. The pumped water would be transferred by pipeline to areas within the regional cone of depression where it is then injected to enhance groundwater recharge. Groundwater flow modeling with zone budget analysis is used to evaluate the potential for net supply gains from induced infiltration at potential sites along major rivers in the region. The groundwater model will further evaluate the impact of the transfer and direct injection on regional water tables.

A new investigation on the water isotopes in the Badain Jaran Desert, China, for inferring water origination

NASA Astrophysics Data System (ADS)

Wu, X.; Wang, Y.; Wang, X. S.; Hu, B.

2017-12-01

Stable isotope δ2H, δ18O and d-excess values of water have previously been used to study the hydraulic connection of groundwater between the surrounding areas such as Heihe River Basin, Qilian Mountain and the Badain Jaran desert (BJD), China. We choose to focus on the effects of strong evaporation on the isotopic characteristics of water in the desert to better understand the origin of water in the BJD. A series of evaporation experiments were conducted in the desert to examine how it may change during evaporation and infiltration under local environmental conditions. Evaporation from open water was monitored in two experiments using local groundwater and lake water, respectively. And evaporation of soil water was observed in three pits which were excavated to different depths below a flat ground surface to install the evaporation-infiltration systems. Water samples were also collected from lakes, a spring and local unconfined aquifer for analyses of stable hydrogen and oxygen isotope ratios, and d-excess values in the BJD. The results show that water isotope contents became progressively enriched along an evaporation line, and the d-excess values decreased with the evaporation. The strong relationship of d-excess and δ18O values was observed from both the experiments and the water samples of groundwater and lakes, which is considered to be a signature of strong evaporation. Also, all the values of groundwater and lake water samples fall along with the evaporation line established through the evaporation experiments, indicating that lakes and groundwater in the study area have evolved from meteoric precipitation under modern or similar to modern climatic conditions. Analysis of a few previously published d-excess and δ18O values of groundwater from the BJD, Lake Eyre Basin, Australia, and Jabal Hafit mountain, United Arab Emirates reveals strong relationships between the two, suggesting similar recharge processes as observed in the BJD. This study demonstrated that the characteristic water isotopic patterns resulting from evaporation could be utilized to help resolve ambiguities in the interpretation of water isotope data in terms of recharge sources, especially, in the arid regions, such as the central Australia and the deserts of United Arab Emirates.

[Characters of infiltration and preferential flow of black soil in Northeast China under different tillage patterns].

PubMed

Li, Wen-Feng; Zhang, Xiao-Ping; Liang, Ai-Zhen; Shen, Yan; Shi, Xiu-Huan; Luo, Jin-Ming; Yang, Xue-Ming

2008-07-01

By using dye tracer and double-ring infiltrometer techniques, the characters of infiltration and preferential flow of black soil under no-tillage (NT) and fall moldboard plow (MP) were compared after six years continuous management. The results showed that the infiltration rate was higher under NT than under MP. When the infiltration reached steady, the infiltration rate and accumulative infiltration capacity under NT were 1.35 and 1.44 times as high as those under MP, respectively. The penetration depth of methylene blue reached a depth of 43 cm in NT soil, being 16 cm deeper than that in MP soil. Comparing with MP soil, NT soil had better development of pore structure and more biological pores, and presented better preferential flow character, which were of importance for water infiltration and soil and water conservation.

Controlled laboratory experiments and modeling of vegetative filter strips with shallow water tables

NASA Astrophysics Data System (ADS)

Fox, Garey A.; Muñoz-Carpena, Rafael; Purvis, Rebecca A.

2018-01-01

Natural or planted vegetation at the edge of fields or adjacent to streams, also known as vegetative filter strips (VFS), are commonly used as an environmental mitigation practice for runoff pollution and agrochemical spray drift. The VFS position in lowlands near water bodies often implies the presence of a seasonal shallow water table (WT). In spite of its potential importance, there is limited experimental work that systematically studies the effect of shallow WTs on VFS efficacy. Previous research recently coupled a new physically based algorithm describing infiltration into soils bounded by a water table into the VFS numerical overland flow and transport model, VFSMOD, to simulate VFS dynamics under shallow WT conditions. In this study, we tested the performance of the model against laboratory mesoscale data under controlled conditions. A laboratory soil box (1.0 m wide, 2.0 m long, and 0.7 m deep) was used to simulate a VFS and quantify the influence of shallow WTs on runoff. Experiments included planted Bermuda grass on repacked silt loam and sandy loam soils. A series of experiments were performed including a free drainage case (no WT) and a static shallow water table (0.3-0.4 m below ground surface). For each soil type, this research first calibrated VFSMOD to the observed outflow hydrograph for the free drainage experiments to parameterize the soil hydraulic and vegetation parameters, and then evaluated the model based on outflow hydrographs for the shallow WT experiments. This research used several statistical metrics and a new approach based on hypothesis testing of the Nash-Sutcliffe model efficiency coefficient (NSE) to evaluate model performance. The new VFSMOD routines successfully simulated the outflow hydrographs under both free drainage and shallow WT conditions. Statistical metrics considered the model performance valid with greater than 99.5% probability across all scenarios. This research also simulated the shallow water table experiments with both free drainage and various water table depths to quantify the effect of assuming the former boundary condition. For these two soil types, shallow WTs within 1.0-1.2 m below the soil surface influenced infiltration. Existing models will suggest a more protective vegetative filter strip than what actually exists if shallow water table conditions are not considered.

Land use, water and Mediterranean landscapes: modelling long-term dynamics of complex socio-ecological systems.

PubMed

Barton, C Michael; Ullah, Isaac I; Bergin, Sean

2010-11-28

The evolution of Mediterranean landscapes during the Holocene has been increasingly governed by the complex interactions of water and human land use. Different land-use practices change the amount of water flowing across the surface and infiltrating the soil, and change water's ability to move surface sediments. Conversely, water amplifies the impacts of human land use and extends the ecological footprint of human activities far beyond the borders of towns and fields. Advances in computational modelling offer new tools to study the complex feedbacks between land use, land cover, topography and surface water. The Mediterranean Landscape Dynamics project (MedLand) is building a modelling laboratory where experiments can be carried out on the long-term impacts of agropastoral land use, and whose results can be tested against the archaeological record. These computational experiments are providing new insights into the socio-ecological consequences of human decisions at varying temporal and spatial scales.

Monitoring induced denitrification during managed aquifer recharge in an infiltration pond

NASA Astrophysics Data System (ADS)

Grau-Martínez, Alba; Folch, Albert; Torrentó, Clara; Valhondo, Cristina; Barba, Carme; Domènech, Cristina; Soler, Albert; Otero, Neus

2018-06-01

Managed aquifer recharge (MAR) is a well-known technique for improving water quality and increasing groundwater resources. Denitrification (i.e. removal of nitrate) can be enhanced during MAR by coupling an artificial recharge pond with a permeable reactive layer (PRL). In this study, we examined the suitability of a multi-isotope approach for assessing the long-term effectiveness of enhancing denitrification in a PRL containing vegetal compost. Batch laboratory experiments confirmed that the PRL was still able to enhance denitrification two years after its installation in the infiltration pond. At the field scale, changes in redox indicators along a flow path and below the MAR-PRL system were monitored over 21 months during recharge and non-recharge periods. Results showed that the PRL was still releasing non-purgeable dissolved organic carbon five years after its installation. Nitrate concentration coupled with isotopic data collected from the piezometer network at the MAR system indicated that denitrification was occurring in the saturated zone immediately beneath the infiltration pond, where recharged water and native groundwater mix. Furthermore, longer operational periods of the MAR-PRL system increased denitrification extent. Multi-isotope analyses are therefore proved to be useful tools in identifying and quantifying denitrification in MAR-PRL systems.

Evaluation of a distributed catchment scale water balance model

NASA Technical Reports Server (NTRS)

Troch, Peter A.; Mancini, Marco; Paniconi, Claudio; Wood, Eric F.

1993-01-01

The validity of some of the simplifying assumptions in a conceptual water balance model is investigated by comparing simulation results from the conceptual model with simulation results from a three-dimensional physically based numerical model and with field observations. We examine, in particular, assumptions and simplifications related to water table dynamics, vertical soil moisture and pressure head distributions, and subsurface flow contributions to stream discharge. The conceptual model relies on a topographic index to predict saturation excess runoff and on Philip's infiltration equation to predict infiltration excess runoff. The numerical model solves the three-dimensional Richards equation describing flow in variably saturated porous media, and handles seepage face boundaries, infiltration excess and saturation excess runoff production, and soil driven and atmosphere driven surface fluxes. The study catchments (a 7.2 sq km catchment and a 0.64 sq km subcatchment) are located in the North Appalachian ridge and valley region of eastern Pennsylvania. Hydrologic data collected during the MACHYDRO 90 field experiment are used to calibrate the models and to evaluate simulation results. It is found that water table dynamics as predicted by the conceptual model are close to the observations in a shallow water well and therefore, that a linear relationship between a topographic index and the local water table depth is found to be a reasonable assumption for catchment scale modeling. However, the hydraulic equilibrium assumption is not valid for the upper 100 cm layer of the unsaturated zone and a conceptual model that incorporates a root zone is suggested. Furthermore, theoretical subsurface flow characteristics from the conceptual model are found to be different from field observations, numerical simulation results, and theoretical baseflow recession characteristics based on Boussinesq's groundwater equation.

Water infiltration and hydraulic conductivity in a natural Mediterranean oak forest: impacts of hydrology-oriented silviculture on soil hydraulic properties

NASA Astrophysics Data System (ADS)

Di Prima, Simone; Bagarello, Vincenzo; Bautista, Inmaculada; Cerdà, Artemi; Cullotta, Sebastiano; del Campo, Antonio; González-Sanchis, María; Iovino, Massimo; Maetzke, Federico

2016-04-01

In the last years researchers reported an increasing need to have more awareness on the intimate link between land use and soil hydrological properties (soil organic matter storage, water infiltration, hydraulic conductivity) and their possible effects on water retention (e.g., Bens et al., 2006; del Campo et al., 2014; González-Sanchis et al., 2015; Molina and del Campo, 2012). In the Mediterranean ecosystems, special attention needs to be paid to the forest-water relationships due to the natural scarcity of water. Adaptive forest management (AFM) aims to adapt the forest to water availability by means of an artificial regulation of the forest structure and density in order to promote tree and stand resilience through enhancing soil water availability (del Campo et al., 2014). The opening of the canopy, due to the removal of a certain number of trees, is an important practice for the management of forests. It results in important modifications to the microclimatic conditions that influence the ecophysiological functioning of trees (Aussenac and Granier, 1988). However, the effect of thinning may vary depending on the specific conditions of the forest (Andréassian, 2004; Brooks et al., 2003; Cosandey et al., 2005; Lewis et al., 2000; Molina and del Campo, 2012). Different authors reported that a reduction in forest cover increases water yield due to the subsequent reduction in evapotranspiration (Brooks et al., 2003; González-Sanchis et al., 2015; Hibbert, 1983; Zhang et al., 2001). On the other hand, the water increase may be easily evaporated from the soil surface (Andréassian, 2004). In this context, determining soil hydraulic properties in forests is essential for understanding and simulating the hydrological processes (Alagna et al., 2015; Assouline and Mualem, 2002), in order to adapt a water-saving management to a specific case, or to study the effects of a particular management practice. However, it must be borne in mind that changes brought about by the practice of forest management persist for almost one century. It is therefore important to monitor managed sites over longer periods, since short-term investigations are insufficient to detect changes that may influence e.g. larger parts of watersheds (Bens et al., 2006). In addition, soil hydraulic properties exhibit strong spatial and temporal variations and a large number of determinations are required to assess the magnitude of the variation within the selected area (Logsdon and Jaynes, 1996). The use of simple and rapid field techniques is therefore important to obtain reliable data with a sustainable effort (Bagarello et al., 2014; Di Prima et al., 2016). The Beerkan Estimation of Soil Transfer (BEST) parameters procedure by Lassabatere et al. (2006) is very attractive for practical use since it allows an estimation of both the soil water retention and the hydraulic conductivity functions from cumulative infiltration collected during a ponded field experiment and a few routinely laboratory determinations. Lassabatere et al. (2006) suggested to measure the infiltration time of small volumes of water repeatedly poured on the soil surface confined by a ring inserted to a depth of about 1 cm into the soil. BEST considers a zero ponded infiltration model which was assumed to be appropriate for an infiltration run performed with small, but positive, pressure heads. This assumption was supported by numerical tests carried out by Touma et al. (2007). Recently, Di Prima (2015) developed a method to automate data collection with a compact infiltrometer under constant head conditions. The device, maintaining a small quasi-constant head of water (i.e., 2-3 mm) on the infiltration surface, is equipped with a differential pressure transducer to measure the stepwise drop of water level in the reservoir, and, in turn, to quantify cumulative infiltration into the soil. The data acquisition system has been designed with low cost components and it is based on the open source microcontroller platform, Arduino. The very limited cost of the system could represent a step towards a cheaper and more widespread application of accurate and automated infiltration rate measurement. However, automatic data collection increases measurement speed, permits measurement at short time intervals, improves measurement precision, allows for more efficient data handling and analysis, and reduces the amount of effort involved and the potential for errors that may occur when manual procedures are applied (Di Prima et al., 2016). The main objective of this study was to determine soil hydraulic properties by using the combination of the automated infiltrometer and the BEST algorithm in a natural Mediterranean oak forest. The forest is located in a typical Mediterranean area, within the public forest La Hunde, Valencia (NE Spain). Two contiguous plots established in previous studies conducted by González-Sanchis et al. (2015) were selected, one of them was thinned reducing the forest density from 861 to 414 tree per ha. Control plot was not thinned. These authors studied the water cycle during the period 2012-2013. In particular, they characterized and compared the plots in term of throughfall, stemflow, soil moisture and transpiration, concluding that the AFM results in an increasing water availability, and at the same time in a substantial maintenance of overland and surface flow, precluding therefore enhancement of erosion rate. In this paper, the focus was put on the impacts of thinning on soil hydraulic properties, such as infiltration capacity, hydraulic conductivity and soil water retention, determined by simplified and low-cost methods in connection with a hydrology-oriented silviculture. Acknowledgements This study is a part of research projects: "Indagini sperimentali per la simulazione dei processi di formazione del deflusso superficiale nei suoli boscati, Progetto FIRB 2012 - MIMOSE", and "CGL2011-28776-C02-02, HYDROSIL" References Alagna, V., Bagarello, V., Di Prima, S., Iovino, M., 2015. Determining hydraulic properties of a loam soil by alternative infiltrometer techniques. Hydrol. Process. doi:10.1002/hyp.10607 Andréassian, V., 2004. Waters and forests: from historical controversy to scientific debate. Journal of Hydrology 291, 1-27. doi:10.1016/j.jhydrol.2003.12.015 Assouline, S., Mualem, Y., 2002. Infiltration during soil sealing: The effect of areal heterogeneity of soil hydraulic properties. Water Resour. Res. 38, 1286. doi:10.1029/2001WR001168 Aussenac, G., Granier, A., 1988. Effects of thinning on water stress and growth in Douglas-fir. Canadian Journal of Forest Research 18, 100-105. doi:10.1139/x88-015 Bagarello, V., Di Prima, S., Iovino, M., Provenzano, G., 2014. Estimating field-saturated soil hydraulic conductivity by a simplified Beerkan infiltration experiment. Hydrological Processes 28, 1095-1103. doi:10.1002/hyp.9649 Bens, O., Wahl, N.A., Fischer, H., Hüttl, R.F., 2006. Water infiltration and hydraulic conductivity in sandy cambisols: impacts of forest transformation on soil hydrological properties. Eur J Forest Res 126, 101-109. doi:10.1007/s10342-006-0133-7 Brooks, K.N., Folliott, P.F., Gregersen, H.M., DeBano, L.F., 2003. Hydrology and the Management of Watersheds. Hydrology and the Management of Watersheds 575. Cosandey, C., Andréassian, V., Martin, C., Didon-Lescot, J.F., Lavabre, J., Folton, N., Mathys, N., Richard, D., 2005. The hydrological impact of the mediterranean forest: a review of French research. Journal of Hydrology 301, 235-249. doi:10.1016/j.jhydrol.2004.06.040 del Campo, A.D., Fernandes, T.J.G., Molina, A.J., 2014. Hydrology-oriented (adaptive) silviculture in a semiarid pine plantation: How much can be modified the water cycle through forest management? European Journal of Forest Research 133, 879-894. doi:10.1007/s10342-014-0805-7 Di Prima, S., 2015. Automated single ring infiltrometer with a low-cost microcontroller circuit. Computers and Electronics in Agriculture 118, 390-395. doi:10.1016/j.compag.2015.09.022 Di Prima, S., Lassabatere, L., Bagarello, V., Iovino, M., Angulo-Jaramillo, R., 2016. Testing a new automated single ring infiltrometer for Beerkan infiltration experiments. Geoderma 262, 20-34. doi:10.1016/j.geoderma.2015.08.006 González-Sanchis, M., del Campo, A., Lidón, A., Lull, C., Bautista, I., García-Prats, A., Francés, F., others, 2015. Incorporación de criterios eco-hidrológicos en la gestión forestal: adaptación a la escasez de agua de una masa marginal de encina. Cuadernos de la Sociedad Española de Ciencias Forestales. Hibbert, A.R., 1983. Water Yield Improvement Potential by Vegetation Management on Western Rangelands1. JAWRA Journal of the American Water Resources Association 19, 375-381. doi:10.1111/j.1752-1688.1983.tb04594.x Lassabatère, L., Angulo-Jaramillo, R., Soria Ugalde, J.M., Cuenca, R., Braud, I., Haverkamp, R., 2006. Beerkan Estimation of Soil Transfer Parameters through Infiltration Experiments - BEST. Soil Science Society of America Journal 70, 521. doi:10.2136/sssaj2005.0026 Lewis, D., Singer, M.J., Dahlgren, R.A., Tate, K.W., 2000. Hydrology in a California oak woodland watershed: a 17-year study. Journal of Hydrology 240, 106-117. doi:10.1016/S0022-1694(00)00337-1 Logsdon, S.D., Jaynes, D.B., 1996. Spatial Variability of Hydraulic Conductivity in a Cultivated Field at Different Times. Soil Science Society of America Journal 60, 703. doi:10.2136/sssaj1996.03615995006000030003x Molina, A.J., del Campo, A.D., 2012. The effects of experimental thinning on throughfall and stemflow: A contribution towards hydrology-oriented silviculture in Aleppo pine plantations. Forest Ecology and Management 269, 206-213. doi:10.1016/j.foreco.2011.12.037 Touma, J., Voltz, M., Albergel, J., 2007. Determining soil saturated hydraulic conductivity and sorptivity from single ring infiltration tests. European Journal of Soil Science 58, 229-238. doi:10.1111/j.1365-2389.2006.00830.x Zhang, L., Dawes, W.R., Walker, G.R., 2001. Response of mean annual evapotranspiration to vegetation changes at catchment scale. Water Resour. Res. 37, 701-708. doi:10.1029/2000WR900325

Infiltration and quality of water for two arroyo channels, Albuquerque, New Mexico, 1988-92

USGS Publications Warehouse

Thomas, Carole L.

1995-01-01

Selected reaches of Grant Line Arroyo and Tijeras Arroyo in Albuquerque, New Mexico, were studied to collect information about the amount and quality of infiltration through arroyo channels. Infiltration rate was calculated for selected reaches of Grant Line Arroyo and Tijeras Arroyo based on instantaneous streamflow-loss volumes, wetted channel area, and instantaneous evaporation rates measured during 1988-92. Infiltration rates at Grant Line Arroyo ranged from 0.0 to 0.6 foot per day, and at Tijeras Arroyo from 2.28 to 30 feet per day. The evaporation rate ranged from one-tenth of 1 percent to 2 percent of the infiltration rate. Infiltration rates differed with the location of the reach isolated for measurement and with the time of day of the infiltration-rate measurement. Differences in intrinsic permeability of the sediments may be the most important factor affecting spatial variations in infiltration. The most important factor affecting temporal variations in infiltration may be the temperature of the water and sediment where infiltration occurs. Annual evaporation rates were greatest over saturated stream sediments and ranged from 802 to 1,025 millimeters per year or from 31.57 to 40.35 inches per year. Annual evaporation rates were least over unsaturated, unvegetated soil and ranged from 174 to 291 millimeters per year or from 6.85 to 11.46 inches per year. Annual evapotranspiration rates over grasses or shrubs or both were about one-half the rates over saturated stream sediments. Rates were similar for Grant Line and Tijeras Arroyos. The land- surface vegetation, availability of water at the land surface, availability of energy to enable a change of state from water to vapor, existence of a vapor concentration gradient, and a turbulent atmosphere to carry the vapor away may be the factors that determine the amount of evaporation and evapotranspiration. Water in Grant Line Arroyo and Tijeras Arroyo met U. S. Environmental Protection Agency drinking-water regulations for nitrate, volatile organic compounds, dissolved lead, and dissolved and total arsenic, barium, cadmium, chromium, copper, iron, silver, zinc, selenium, chloride, and sulfate concentrations. Total lead concentration in one sample from Tramway Floodway Channel, a tributary to Tijeras Arroyo, was 55 micrograms per liter, exceeding the Environmental Protection Agency drinking-water regulation of 50 micrograms per liter. Dissolved-solids concentrations calculated from the sum of cations and anions usually exceeded the Environmental Protection Agency drinking-water dissolved-solids regulation of 500 milligrams per liter at Tijeras Arroyo above Four Hills Bridge.

Migration and transformation of different phosphorus forms in rainfall runoff in bioretention system.

PubMed

Song, Yujia; Song, Shoufa

2018-06-04

Artificial bioretention system consisting of Ophiopogon japonicus infiltration medium was used to simulate an infiltration experiment of rainfall runoff. Continuous extraction method was used to detect contents of inorganic phosphorus (P) under exchangeable state (Ex-P) and aluminium phosphate (Al-P) and iron phosphate (Fe-P) at different depths (0, 5, 15 and 35 cm) of soil infiltration medium in bioretention system. Effluent total P (TP) concentration of the system was also monitored. Results indicated that the adsorption of inorganic P, Al-P and Fe-P by soil infiltration medium was implemented layer by layer from top to bottom and gradually weakened. Moreover, Ex-P was gradually transformed into Al-P and Fe-P, whereas Al-P was gradually transformed into Fe-P; thus, Ex-P content reduced layer by layer, whereas Al-P and Fe-P gradually accumulated. The TP removal rate in runoff rainwater by the system was more than 90%, where the TP that was not used by plants was under dynamic equilibrium in water-soil-root system/biological system.

Prediction of unsaturated flow and water backfill during infiltration in layered soils

NASA Astrophysics Data System (ADS)

Cui, Guotao; Zhu, Jianting

2018-02-01

We develop a new analytical infiltration model to determine water flow dynamics around layer interfaces during infiltration process in layered soils. The model mainly involves the analytical solutions to quadratic equations to determine the flux rates around the interfaces. Active water content profile behind the wetting front is developed based on the solution of steady state flow to dynamically update active parameters in sharp wetting front infiltration equations and to predict unsaturated flow in coarse layers before the front reaches an impeding fine layer. The effect of water backfill to saturate the coarse layers after the wetting front encounters the impeding fine layer is analytically expressed based on the active water content profiles. Comparison to the numerical solutions of the Richards equation shows that the new model can well capture water dynamics in relation to the arrangement of soil layers. The steady state active water content profile can be used to predict the saturation state of all layers when the wetting front first passes through these layers during the unsteady infiltration process. Water backfill effect may occur when the unsaturated wetting front encounters a fine layer underlying a coarse layer. Sensitivity analysis shows that saturated hydraulic conductivity is the parameter dictating the occurrence of unsaturated flow and water backfill and can be used to represent the coarseness of soil layers. Water backfill effect occurs in coarse layers between upper and lower fine layers when the lower layer is not significantly coarser than the upper layer.

Characterizing Heterogeneity in Infiltration Rates During Managed Aquifer Recharge.

PubMed

Mawer, Chloe; Parsekian, Andrew; Pidlisecky, Adam; Knight, Rosemary

2016-11-01

Infiltration rate is the key parameter that describes how water moves from the surface into a groundwater aquifer during managed aquifer recharge (MAR). Characterization of infiltration rate heterogeneity in space and time is valuable information for MAR system operation. In this study, we utilized fiber optic distributed temperature sensing (FO-DTS) observations and the phase shift of the diurnal temperature signal between two vertically co-located fiber optic cables to characterize infiltration rate spatially and temporally in a MAR basin. The FO-DTS measurements revealed spatial heterogeneity of infiltration rate: approximately 78% of the recharge water infiltrated through 50% of the pond bottom on average. We also introduced a metric for quantifying how the infiltration rate in a recharge pond changes over time, which enables FO-DTS to be used as a method for monitoring MAR and informing maintenance decisions. By monitoring this metric, we found high-spatial variability in how rapidly infiltration rate changed during the test period. We attributed this variability to biological pore clogging and found a relationship between high initial infiltration rate and the most rapid pore clogging. We found a strong relationship (R 2  = 0.8) between observed maximum infiltration rates and electrical resistivity measurements from electrical resistivity tomography data taken in the same basin when dry. This result shows that the combined acquisition of DTS and ERT data can improve the design and operation of a MAR pond significantly by providing the critical information needed about spatial variability in parameters controlling infiltration rates. © 2016, National Ground Water Association.

Experimental study of water fluxes in a residential area: 2. Road infiltration, runoff and evaporation

NASA Astrophysics Data System (ADS)

Ragab, R.; Rosier, P.; Dixon, A.; Bromley, J.; Cooper, J. D.

2003-08-01

Lack of accurate data has led some hydrologists and city planners to assume that urban infiltration is zero and runoff is 100% of the rainfall. These assumptions lead to an over estimation of road runoff volume and an underestimation of direct recharge to groundwater, which is already rising under some UK cities. This study investigates infiltration and runoff processes and quantifies the percentage of rainfall that contributes to storm drainage, and that which infiltrates through different types of road surface. Access tubes were installed for measuring soil water content using a neutron probe in three car parks, a road and a grass site at the Centre for Ecology and Hydrology, Crowmarsh Gifford, Wallingford. Storm drainage was recorded at the exit of the Thamesmead Estate in Crowmarsh Gifford, just before the drain joins the River Thames at Wallingford. Rainfall and water table depth were also recorded. Weekly measurements of soil moisture content indicated that the top 40 cm layer is not influenced by water-table fluctuations and, therefore, positive changes in soil moisture could be attributed to infiltration of rainfall through the surface. Depending on the nature of the surface, subsurface layers, level of traffic, etc., between 6 and 9% of rainfall was found to infiltrate through the road surfaces studied. The storm drainage generated by road runoff revealed a flow pattern similar to that of the receiving watercourse (River Thames) and increased with the increase of infiltration and soil water content below the road surface. The ratio of runoff to rainfall was 0·7, 0·9 and 0·5 for annual, winter (October-March) and summer (April-September) respectively. As the results of the infiltration indicated that 6 to 9% of annual rainfall infiltrates through the road surface, this means that evaporation represents, 21-24% of annual rainfall, with more evaporation taking place during summer than winter.

30 CFR 817.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... infiltration to ground-water systems and by managing excavations and other disturbances to prevent or control... formation of polluted runoff, and the infiltration of polluted water. Storage shall be limited to the period...

30 CFR 817.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... infiltration to ground-water systems and by managing excavations and other disturbances to prevent or control... formation of polluted runoff, and the infiltration of polluted water. Storage shall be limited to the period...

30 CFR 817.41 - Hydrologic-balance protection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... infiltration to ground-water systems and by managing excavations and other disturbances to prevent or control... formation of polluted runoff, and the infiltration of polluted water. Storage shall be limited to the period...

Infiltration Variability in Agricultural Soil Aggregates Caused by Air Slaking

NASA Astrophysics Data System (ADS)

Korenkova, L.; Urik, M.

2018-04-01

This article reports on variation in infiltration rates of soil aggregates as a result of phenomenon known as air slaking. Air slaking is caused by the compression and subsequent escape of air captured inside soil aggregates during water saturation. Although it has been generally assumed that it occurs mostly when dry aggregates are rapidly wetted, the measurements used for this paper have proved that it takes place even if the wetting is gradual, not just immediate. It is a phenomenon that contributes to an infiltration variability of soils. In measuring the course of water flow through the soil, several small aggregates of five agricultural soils were exposed to distilled water at zero tension in order to characterize their hydraulic properties. Infiltration curves obtained for these aggregates demonstrate the effect of entrapped air on the increase and decrease of infiltration rates. The measurements were performed under various moisture conditions of the A-horizon aggregates using a simple device.

Absorption of water and lubricating oils into porous nylon

NASA Technical Reports Server (NTRS)

Bertrand, P. A.

1995-01-01

Oil and water absorption from air into sintered porous nylon can be described by infiltration into the pores of the material. This process can be modeled by a diffusion-like mechanism. For water absorption, we find a formal diffusion coefficient of 1.5 x 10(exp -4)sq cm/min when the nylon is initially dry. The diffusion coefficient is 4 x 10(exp -6)sq cm/min when the nylon is oil-impregnated prior to air exposure. In a 52% RH atmosphere, dry nylon absorbs 3% w/w water, and oil-impregnated nylon absorbs 0.6% w/w water. For oil absorption there are three steps: (1) surface absorption and infiltration into (2) larger and (3) smaller pores. Surface absorption is too fast to be measured in these experiments. The diffusion coefficient for the second step is 6 x 10(exp -4)sq cm/min for SRG-60 oil into dry nylon and 4 x 10(exp -4)sq cm/min for air-equilibrated nylon. The diffusion coefficient for the third step is about 1 x 10(exp -6)sq cm/min for both cases. The total amount of oil absorbed is 31% w/w. The interaction between water and nylon is not as strong as that between water and cotton-phenolic: oil can replace water, and only a small amount of water can enter previously oil-impregnated nylon.

Shallow water table effects on water, sediment, and pesticide transport in vegetative filter strips - Part 1: nonuniform infiltration and soil water redistribution

NASA Astrophysics Data System (ADS)

Muñoz-Carpena, Rafael; Lauvernet, Claire; Carluer, Nadia

2018-01-01

Vegetation buffers like vegetative filter strips (VFSs) are often used to protect water bodies from surface runoff pollution from disturbed areas. Their typical placement in floodplains often results in the presence of a seasonal shallow water table (WT) that can decrease soil infiltration and increase surface pollutant transport during a rainfall-runoff event. Simple and robust components of hydrological models are needed to analyze the impacts of WT in the landscape. To simulate VFS infiltration under realistic rainfall conditions with WT, we propose a generic infiltration solution (Shallow Water table INfiltration algorithm: SWINGO) based on a combination of approaches by Salvucci and Entekhabi (1995) and Chu (1997) with new integral formulae to calculate singular times (time of ponding, shift time, and time to soil profile saturation). The algorithm was tested successfully on five distinct soils, both against Richards's numerical solution and experimental data in terms of infiltration and soil moisture redistribution predictions, and applied to study the combined effects of varying WT depth, soil type, and rainfall intensity and duration. The results show the robustness of the algorithm and its ability to handle various soil hydraulic functions and initial nonponding conditions under unsteady rainfall. The effect of a WT on infiltration under ponded conditions was found to be effectively decoupled from surface infiltration and excess runoff processes for depths larger than 1.2 to 2 m, being shallower for fine soils and shorter events. For nonponded initial conditions, the influence of WT depth also varies with rainfall intensity. Also, we observed that soils with a marked air entry (bubbling pressure) exhibit a distinct behavior with WT near the surface. The good performance, robustness, and flexibility of SWINGO supports its broader use to study WT effects on surface runoff, infiltration, flooding, transport, ecological, and land use processes. SWINGO is coupled with an existing VFS model in the companion paper (Lauvernet and Muñoz-Carpena, 2018), where the potential effects of seasonal or permanent WTs on VFS sediment and pesticide trapping are studied.

Water repellent soils following prescribed burning treatments and a wildfire in the oak savannas of the Malpai Borderlands Region

Treesearch

Cody L. Stropki; Peter F. Ffolliott; Gerald J. Gottfried

2009-01-01

Water repellent (hydrophobic) soils impact the infiltration process of a water budget by restricting the movement of water into and through a soil body. The infiltration of water into a water repellent soil can be inhibited or completely impeded in which case much of the incoming precipitation reaching the soil surface becomes overland flow. One mechanism causing the...

An analytical solution to the one-dimensional heat conduction-convection equation in soil

USDA-ARS?s Scientific Manuscript database

Heat transfer in soil occurs by conduction and convection. Infiltrating water affects soil temperature distributions, and measuring soil temperature distributions below infiltrating water can provide a signal for the flux of water. In earlier work a sine wave function (hereinafter referred to as the...

Streambed infiltration and ground-water flow from the trout creek drainage, an intermittent tributary to the Humboldt River, north-central Nevada: Chapter K in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Prudic, David E.; Niswonger, Richard G.; Harrill, James R.; Wood, James L.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

Ground water is abundant in many alluvial basins of the Basin and Range Physiographic Province of the western United States. Water enters these basins by infiltration along intermittent and ephemeral channels, which originate in the mountainous regions before crossing alluvial fans and piedmont alluvial plains. Water also enters the basins as subsurface ground-water flow directly from the mountains, where infiltrated precipitation recharges water-bearing rocks and sediments at these higher elevations. Trout Creek, a typical intermittent stream in the Middle Humboldt River Basin in north-central Nevada, was chosen to develop methods of estimating and characterizing streambed infiltration and ground-water recharge in mountainous terrains. Trout Creek has a drainage area of about 4.8 × 107 square meters. Stream gradients range from more than 1 × 10–1 meter per meter in the mountains to 5 × 10–3 meter per meter at the foot of the piedmont alluvial plain. Trout Creek is perennial in short reaches upstream of a northeast-southwest trending normal fault, where perennial springs discharge to the channel. Downstream from the fault, the water table drops below the base of the channel and the stream becomes intermittent.Snowmelt generates streamflow during March and April, when streamflow extends onto the piedmont alluvial plain for several weeks in most years. Rates of streambed infiltration become highest in the lowest reaches, at the foot of the piedmont alluvial plain. The marked increases in infiltration are attributed to increases in streambed permeability together with decreases in channel-bed armoring, the latter which increases the effective area of the channel. Large quartzite cobbles cover the streambed in the upper reaches of the stream and are absent in the lowest reach. Such changes in channel deposits are common where alluvial fans join piedmont alluvial plains. Poorly sorted coarse and fine sediments are deposited near the head of the fan, while finer-grained but better sorted gravels and sands are deposited near the foot.All flow in Trout Creek is lost to infiltration in the upper and middle reaches of the channel during years of normal to below-normal precipitation. During years of above-normal precipitation, streamflow extends beyond the piedmont alluvial plain to the lower reaches of the channel, where high rates of infiltration result in rapid stream loss. The frequency and duration of streambed infiltration is sufficient to maintain high water contents and low chloride concentrations, compared with interchannel areas, to depths of at least 6 m beneath the channel. Streamflow, streambed infiltration, and unsaturated-zone thickness are all highly variable along intermittent streams, resulting in recharge that is highly variable as well.Average annual ground-water recharge in the mountainous part of the Trout Creek drainage upstream of Marigold Mine was estimated on the basis of chloride balance to be 5.2 × 105 cubic meters. Combined with an average annual surface runoff exiting the mountains of 3.4 × 105cubic meters, the total annual volume of inflow to alluvial-basin sediments from the mountainous part of the Trout Creek is 8.6 × 105 cubic meters, assuming that all runoff infiltrates the stream channel. This equates to about 7 percent of average annual precipitation, which is about the same percentage estimated for ground-water recharge using the original Maxey-Eakin method.

Ephemeral-stream channel and basin-floor infiltration and recharge in the Sierra Vista subwatershed of the Upper San Pedro Basin, Southeastern Arizona: Chapter J in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Coes, A.L.; Pool, D.R.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

The timing and location of streamflow in the San Pedro River are partially dependent on the aerial distribution of recharge in the Sierra Vista subwatershed. Previous investigators have assumed that recharge in the subwatershed occurs only along the mountain fronts by way of stream-channel infiltration near the contact between low-permeability rocks of the mountains and the basin fill. Recent studies in other alluvial basins of the Southwestern United States, however, have shown that significant recharge can occur through the sediments of ephemeral stream channels at locations several kilometers distant from the mountains. The purpose of this study was to characterize the spatial distribution of infiltration and subsequent recharge through the ephemeral channels in the Sierra Vista subwatershed.Infiltration fluxes in ephemeral channels and through the basin floor of the subwatershed were estimated by using several methods. Data collected during the drilling and coring of 16 boreholes included physical, thermal, and hydraulic properties of sediments; chloride concentrations of sediments; and pore-water stable-isotope values and tritium activity. Surface and subsurface sediment temperatures were continuously measured at each borehole.Twelve boreholes were drilled in five ephemeral stream channels to estimate infiltration within ephemeral channels. Active infiltration was verified to at least 20 meters at 11 of the 12 borehole sites on the basis of low sediment-chloride concentrations, high soil-water contents, and pore-water tritium activity similar to present-day precipitation. Consolidated sediments at the twelfth site prevented core recovery and estimation of infiltration. Analytical and numerical methods were applied to determine the surface infiltration flux required to produce the observed sediment-temperature fluctuations at six sites. Infiltration fluxes were determined for summer ephemeral flow events only because no winter flows were recorded at the sites during the monitoring period.Four boreholes were drilled in the basin floor to estimate infiltration in areas between ephemeral channels. Infiltration fluxes through the basin floor ranged from less than 1 centimeter to 6 centimeters per year. At a site in semiconsolidated to consolidated basin-fill conglomerate, the long-term infiltration fluxes were very low (less than 1 centimeter per year). Chloride, tritium, and stable-isotope data indicate long periods of no net deep downward percolation flux beneath the basin floor. At a site in unconsolidated to semiconsolidated basin-fill sand and gravel, infiltration fluxes were high (2 to 6 centimeters per year). Chloride, tritium, and stable-isotope data indicate active infiltration to 8 meters, and a decrease in infiltration below 8 meters. The change in the infiltration rate below 8 meters is controlled by an increase in the silt and clay content of the sediment.Ephemeral-channel recharge for the entire subwatershed was estimated by upscaling the calculated infiltration fluxes and weighting the fluxes by streamflow duration, evaporation, and transpiration. In contrast to previous assumptions, recharge from ephemeral-streamflow infiltration occurs not only near the mountain fronts, but also along significant lengths of ephemeral channels. Although most of the ephemeral streams in the subwatershed flow less than a few days per year, the available streamflow quickly infiltrates past depths where it is available for evapotranspiration. This water likely stays in the unsaturated zone until it is vertically displaced by infiltrated water from subsequent streamflows and eventually recharges the regional aquifer. Ephemeral-channel infiltration during 2001 and 2002 was estimated to account for about 12 to 19 percent of the estimated average annual recharge in the Sierra Vista subwatershed.

2D and 3D Ground Penetrating Radar monitoring of a reinforced concrete asphalt plate affected by mechanical deformation.

NASA Astrophysics Data System (ADS)

Bavusi, M.; Dumoulin, J.; Loperte, A.; Rizzo, E.; Soldovieri, F.

2012-04-01

The main facility of Hydrogeosite Laboratory of the Italian National Research Council (Marsico Nuovo, CNR) is a 3m x 7m x 10m reinforced concrete pool filled by siliceous sand designed for hydrologic experiments. One of its peculiarities is the possibility to vary the water table depth by using a proper hydraulic system [1]. In the framework of the FP7 ISTIMES project (Integrated System for Transport Infrastructure surveillance and Monitoring by Electromagnetic Sensing), a 3m x 3m layered structure has been purposely built and placed in the pool of the Hydrogeosite Laboratory with the aim to carry out a long term monitoring, by using jointly several electromagnetic sensing technologies, during two different phases simulating the rising of the water table and a mechanical solicitation. Several layers composed the structure from the top to the bottom, such as: 5 cm of asphalt; 5-10 cm of reinforced concrete; 20-25 cm of conglomerate, 55 cm of sand. Moreover, in the sand layer, three (metallic and plastic) pipes of different size were buried to simulate utilities. Ground Penetrating Radar (GPR) surveys were performed by using a the GSSI SIR 3000 system equipped with 400 MHz and 1500 MHz central frequency antennas. Surveys carried out by means of 400 MHz antenna allowed to detect and localize the three pipes (one in plastic and two in metal) and to investigate the effects of the sand water content on their radar signature. Surveys carried out by using 1500 MHz antenna were focused to characterize the shallower layers of the structure. The Hydrogeosite experiment consisted in following stages: • Arising of a water table by infiltration from the bottom; • Water gravity infiltration condescendingly; • Infiltration by peristaltic pump in the very shallow layers of the structure; • Water table drawdown; • Mechanical structure deformation; • Asphalt plate restoration after mechanical solicitation. After each stage a series of GPR surveys was performed. Moreover, a zero setting acquisition was carried out before perturbing the plate. Described experience demonstrates the GPR is a reliable technique for the: • foundation soil characterization and monitoring • Reinforced structural elements monitoring • asphalt/reinforced concrete characterization and monitoring • detection of water infiltration, structural elements, defects • evaluation of restoration intervention. In fact, the GPR technique was able to investigate the layers beyond the asphalt and provides a spatial resolution complying with the needs of the technical problem at hand by use of different antennas. Moreover noticeable performances of this technique can be further improved by implementing 3D processing and MT inversion procedures in order to increase the amount of information by the survey [2]. Acknowledgements. The research leading to these results has received funding from the European Community's Seventh Framework Programme (FP7/2007-2013) under Grant Agreement n. 225663 Joint Call FP7-ICT-SEC-2007-1 [1] Lapenna, V.; Cuomo, V.; Rizzo, E.; Fiore, S.; Troisi, S.; Straface, S. (2006). A new Large Lab-scale Facility for Hydro-Geophysical Experiments: Hydrogeosite. American Geophysical Union, Fall Meeting 2006, abstract #H31B-1422 [2] Bavusi M., Soldovieri F., Di Napoli R., Loperte A., Di Cesare A., Ponzo F.C and Lapenna V. (2011). Ground penetrating radar and microwave tomography 3D applications for the deck evaluation of the Musmeci bridge in Potenza, Italy. J. Geophys. Eng. 8 S33 doi:10.1088/1742-2132/8/3/S04

3D time-lapse Electrical Resistivity Tomography (ERT) to monitor subsurface flow processes during a sprinkling and injection experiment on a mountain slope

NASA Astrophysics Data System (ADS)

Inauen, C.; Green, A.; Rabenstein, L.; Greenhalgh, S.; Kinzelbach, W.; Doetsch, J.; Hertrich, M.; Smoorenburg, M.; Volze, N.

2012-04-01

Understanding the relationships between precipitation volumes, surface runoff and subsurface storage, drainage and flow processes on mountain slopes is critical for flood management in alpine regions. In the Schächen catchment (central Switzerland) an unexpectedly delayed and heavy flood reaction to a long duration rainfall event was observed in 2005. It is believed that the steep creeping landmass slopes with thick soils were responsible for the delay. To better comprehend and visualise water infiltration and runoff formation we conducted a 3D time-lapse ERT experiment during a water sprinkling and injection experiment on the side of a hill in the Schächental region presumed representative of soil and other conditions associated with the delayed flood. Constant sprinkling at a rate of about 10mm/h was applied to a plot of area 30m x 5m. The electrical conductivity of the sprinkled water was approximately that of the pore water (25mS/m). A total of 33 consecutive ERT data sets, each comprising 3521 measured electrode configurations, were recorded with a 96-electrode array over an area of 27.5m x 14m, which included two thirds of the sprinkled area. Each electrode configuration was measured at a repeat interval of 2 to 2.8 hours. The entire 3D ERT monitoring experiment was divided into two separate time intervals: (1) the initial 25 hour period involving only freshwater sprinkling, until steady state was reached, (2) the following 35 hour period during which, in addition to the sprinkling, salt water was injected in two boreholes at a depth of 1m (unsaturated zone). The salt water injections were separated by 17 hours, and monitored until 14 hours after sprinkling stopped. During the first interval all changes in the subsurface resistivity are caused by changes in the water saturation and the temperature of the fluid, whereas in the second interval they are mainly due to changes in salt concentration of the pore fluid. Supplementary measurements of water table elevation and fluid electric conductivity were made in several boreholes. To image the subsurface resistivity changes, we inverted the ratios of time-lapse resistances to their background (pre-sprinkling) values. The sprinkling during time interval 1 allowed us to examine near-surface infiltration. Even from the first time window, the emergence of a shallow wetting front could be observed in the inverted depth sections as a decrease in bulk resistivity. Both salt water plumes during interval 2 were found to move laterally as well as vertically through the soil into a zone of fissured Flysch. Below the water table, the plume could be tracked further as a weaker ERT signal, which shows a flow component parallel to the water table in the downslope direction where it eventually breaks the surface. 3D ERT monitoring has proven to be a powerful tool to monitor water sprinkling and injection experiments. Due to its advantageous ability to resolve changes, both in time and in space, it captured most of the soil moisture and flow dynamics. Processes, such as infiltration and drainage, which are important for the understanding of runoff formation, could be readily visualized.

A soil water budget model for precipitation-induced shallow landslides

NASA Astrophysics Data System (ADS)

Yeh, Hsin-Fu; Lee, Cheng-Haw

2013-04-01

Precipitation infiltration influences both the quantity and quality of slope systems. Knowledge of the mechanisms leading to precipitation-induced slope failures is of great importance to the management of landslide hazard. In this study, a soil water balance model is developed to estimate soil water flux during the process of infiltration from rainfall data, with consideration of storm periods and non-storm periods. Two important assumptions in this study are given: (1) instantaneous uniform distribution of the degree of effective saturation and (2) a linear relationship between evapotranspiration and the related degree of saturation degree. For storm periods, the Brooks and Corey model estimates both the soil water retention curve (SWRC) and soil water parameters. The infiltration partition is employed by an infinite-series solution of Philip in conjunction with the time compression approximation (TCA). For none-storm periods, evapotranspiration can be derived for the moisture depletion of soil water. This study presents a procedure for calculating the safety factor for an unsaturated slope suffering from precipitation infiltration. The process of infiltration into a slope due to rainfall and its effect on soil slope behavior are examined using modified Mohr-Coulomb failure criterion in conjunction with a soil water balance model. The results indicate that the matric suction, which is closely related to slope stability, is affected by the effective degree of saturation controlled by rainfall events.

Design and application of a drip-type rainfall simulator adapted to steep topography and low intensity-rainfall characteristics in the Coastal Range of Southern Chile

NASA Astrophysics Data System (ADS)

Mohr, Christian; Anton, Huber

2010-05-01

Besides being adaptable for measuring infiltration, overland flow and sediment transport simultaneously, rainfall simulator systems allow the observation of the processes of runoff generation and soil erosion, too. This enables the assimilation of additional qualitative data and makes a rainfall simulator system a very valid method in the investigation of soil-hydrological response to precipitation events. In the present study a cheap, handy, transportable and easy to set up rainfall simulator applicable for the steep terrain conditions of the Southern Chilean Coastal range was designed based on Bowyer-Bower & Burt (1989). The used drip-type rainfall simulator had to fulfill two main requirements: adaptive to steep topography and little in water consumption. The used simulator is set up by a dismountable rectangular metal rack of 0.5x1.0m basal surface and 2.5m height. The metallic structure enables the attachment of plastic boards for wind protection. Fixable telescopic extensions allow a firm adjustment to slopes up to 45°. Horizontal metallic frames at different heights increase the stability of the structure and carry the devices of the rainfall simulator. On the uppermost frame, two containers provided with calibrated scales spend the water to a fast reacting receptacle assuring constant water supply and pressure by the Mariotte's principle. The rainfall intensity is adjusted by a control-panel according to the Bernoulli principle. This guarantees a constant water flow which was verified by the water-volume leaving the calibrated containers on top. Interchangeable glass-tubes of different diameters in the control-panel permit the generation of various precipitation intensities (4-60 mm/h; SD =0.16mm). The frame beneath carries an acrylic glass box with approx. 600 drop-formers (fishing line inside a 0.76mm Tygon-tube) at its bottom. 20 cm below, a framed 5mm-spacing-mesh serves as a raindrop randomizer. At the base of the simulator sheet metals avoid lateral leakage of overland flow leading the runoff to a cemented trough. The experiments were conducted until a steady state infiltration rate was observed or the runoff ceased. The runoff samples are taken manually in intervals of 5 or 10 min depending on the simulated intensity and amount of runoff. All bottled samples were filtered to determine the sediment concentration. To test the system's effectiveness a pilot-study was conducted in a granitic soil catchment. The obtained values of the infiltration rate indicate that soil physical properties in this area facilitate rapid infiltration and slope did not show main influence. The sediment concentration showed high variability due to heterogeneity of surface and soil characteristics. In a succeeding study 36 rainfall simulations prior to clear-cuts during dry summer-season and rainy winter-season were carried out to determine the effect of both silvicultural practices on micro-scale. Soil hydrological response showed preferential flow patterns and variable infiltration-rates due to topsoil disturbance in the course of previous timber-harvests and differences in soil depth, hydrophobic organic layers and imbedded rocks. Maximum steady state infiltration rates ranged between 7.3 and 32.3 mm/h. In contrast to the expected results, maximum infiltration occurred at steep slopes. Only little sediment transport was measured. Only under high precipitation on steep slopes a moderate sediment transport (0.074 g/l) was documented. Post clear-cut infiltration experiments will be conducted in Jan.-March 2010. Furthermore, a modified tipping-bucket-device will be installed as a runoff collector-device to gain better temporal resolution.

Partitioning Hydrologic and Biological Drivers of Discharge Loss in Arctic Headwater Streams

NASA Astrophysics Data System (ADS)

Koch, J. C.; Carey, M.; O'Donnell, J. A.; Records, M. K.; Sjoberg, Y.; Zimmerman, C. E.

2017-12-01

The Arctic-Boreal transition (ABT) zone of Alaska is experiencing unprecedented warming, leading to permafrost thaw and vegetation change. Both of these processes are likely to affect streams and stream ecosystems, but there is little direct empirical evidence regarding the magnitude of these effects and their relative importance. To understand how permafrost thaw and vegetation are affecting streams at the ABT, we monitored 8 first-order streams that drain catchments varying in elevation, aspect, and vegetation cover. Data were obtained from meteorological stations, continuous stream discharge, seepage runs, and stream tracer experiments. Hydrograph analysis indicated that runoff ratios in south-facing catchments were lower than north-facing catchments and decreased over the season. Seepage runs indicated that south-facing catchments lost a large portion of water (up to 50% per km stream reach) in the late summer, while north-facing catchments were gaining water. All streams displayed diel variability in discharge, but with different daily and seasonal trends related to aspect and elevation. South-facing, forested catchment streams showed diel discharge timing consistent with cycles in evapotranspiration rates, while the signal in north-facing catchments and those dominated by tundra was more consistent with thermal controls on water viscosity and groundwater discharge to streams. Together, these signals indicate that the warmer, south-facing catchments are losing a large portion of water to a combination of infiltration and evapotranspiration. The seasonal trends are consistent with higher infiltration rates beneath south-facing streams as the ground thaws over the summer. The magnitude and seasonal dynamics of the diel signatures help separate biological (i.e. evapotranspiration) vs. physical controls (i.e. frozen ground hydrology) on stream-catchment interactions, which vary depending on aspect, elevation, and vegetation cover. Warming, and subsequent increases in infiltration and evapotranspiration rates may cause some south-facing streams to become ephemeral in the near future. This infiltration feeds aquifers and ultimately larger rivers, potentially explaining hydrograph shifts observed on the larger, river scale in permafrost environments.

Laboratory experiments on solute transport in bimodal porous media under cyclic precipitation-evaporation boundary conditions

NASA Astrophysics Data System (ADS)

Cremer, Clemens; Neuweiler, Insa

2016-04-01

Flow and solute transport in the shallow subsurface is strongly governed by atmospheric boundary conditions. Erratically varying infiltration and evaporation cycles lead to alternating upward and downward flow, as well as spatially and temporally varying water contents and associated hydraulic conductivity of the prevailing materials. Thus presenting a highly complicated, dynamic system. Knowledge of subsurface solute transport processes is vital to assess e.g. the entry of, potentially hazardous, solutes to the groundwater and nutrient uptake by plant roots and can be gained in many ways. Besides field measurements and numerical simulations, physical laboratory experiments represent a way to establish process understanding and furthermore validate numerical schemes. With the aim to gain a better understanding and to quantify solute transport in the unsaturated shallow subsurface under natural precipitation conditions in heterogeneous media, we conduct physical laboratory experiments in a 22 cm x 8 cm x 1 cm flow cell that is filled with two types of sand and apply cyclic infiltration-evaporation phases at the soil surface. Pressure at the bottom of the domain is kept constant. Following recent studies (Lehmann and Or, 2009; Bechtold et al., 2011a), heterogeneity is introduced by a sharp vertical interface between coarse and fine sand. Fluorescent tracers are used to i) qualitatively visualize transport paths within the domain and ii) quantify solute leaching at the bottom of the domain. Temporal and spatial variations in water content during the experiment are derived from x-ray radiographic images. Monitored water contents between infiltration and evaporation considerably changed in the coarse sand while the fine sand remained saturated throughout the experiments. Lateral solute transport through the interface in both directions at different depths of the investigated soil columns were observed. This depended on the flow rate applied at the soil surface and significantly influenced solute leaching. Dynamic boundary conditions generally resulted in faster initial breakthrough and stronger tailing. References: Bechtold, M., S. Haber-Pohlmeier, J. Vanderborght, A. Pohlmeier, T.P.A. Ferré and H. Veerecken. 2011a. Near-surface solute redistribution during evaporation. Geophys. Res. Lett., 38, L17404, doi:10.1029/2011GL048147. Lehmann, P. and D. Or. 2009. Evaporation and capillary coupling across vertical textural contrasts in porous media. Phys. Rev. E, 80, 046318, doi:10.1103/PhysRevE.80.046318.

Modeling runoff and microbial overland transport with KINEROS2/STWIR model: Accuracy and uncertainty as affected by source of infiltration parameters

EPA Science Inventory

Infiltration is important to modeling the overland transport of microorganisms in environmental waters. In watershed- and hillslope scale-models, infiltration is commonly described by simple equations relating infiltration rate to soil saturated conductivity and by empirical para...

Green-ampt infiltration parameters in riparian buffers

Treesearch

L.M. Stahr; D.E. Eisenhauer; M.J. Helmers; Mike G. Dosskey; T.G. Franti

2004-01-01

Riparian buffers can improve surface water quality by filtering contaminants from runoff before they enter streams. Infiltration is an important process in riparian buffers. Computer models are often used to assess the performance of riparian buffers. Accurate prediction of infiltration by these models is dependent upon accurate estimates of infiltration parameters....

Mixed artificial grasslands with more roots improved mine soil infiltration capacity

NASA Astrophysics Data System (ADS)

Wu, Gao-Lin; Yang, Zheng; Cui, Zeng; Liu, Yu; Fang, Nu-Fang; Shi, Zhi-Hua

2016-04-01

Soil water is one of the critical limiting factors in achieving sustainable revegetation. Soil infiltration capacity plays a vital role in determining the inputs from precipitation and enhancing water storage, which are important for the maintenance and survival of vegetation patches in arid and semi-arid areas. Our study investigated the effects of different artificial grasslands on soil physical properties and soil infiltration capacity. The artificial grasslands were Medicago sativa, Astragalus adsurgens, Agropyron mongolicum, Lespedeza davurica, Bromus inermis, Hedysarum scoparium, A. mongolicum + Artemisia desertorum, A. adsurgens + A. desertorum and M. sativa + B. inermis. The soil infiltration capacity index (SICI), which was based on the average infiltration rate of stage I (AIRSI) and the average infiltration rate of stage III (AIRS III), was higher (indicating that the infiltration capacity was greater) under the artificial grasslands than that of the bare soil. The SICI of the A. adsurgens + A. desertorum grassland had the highest value (1.48) and bare soil (-0.59) had the lowest value. It was evident that artificial grassland could improve soil infiltration capacity. We also used principal component analysis (PCA) to determine that the main factors that affected SICI were the soil water content at a depth of 20 cm (SWC20), the below-ground root biomasses at depths of 10 and 30 cm (BGB10, BGB30), the capillary porosity at a depth of 10 cm (CP10) and the non-capillary porosity at a depth of 20 cm (NCP20). Our study suggests that the use of Legume-poaceae mixtures and Legume-shrub mixtures to create grasslands provided an effective ecological restoration approach to improve soil infiltration properties due to their greater root biomasses. Furthermore, soil water content, below-ground root biomass, soil capillary porosity and soil non-capillary porosity were the main factors that affect the soil infiltration capacity.

Spatial regression between soil surface elevation, water storage in root zone and biomass productivity of alfalfa within an irrigated field

NASA Astrophysics Data System (ADS)

Zeyliger, Anatoly; Ermolaeva, Olga

2014-05-01

Efficiency of water use for the irrigation purposes is connected to the variety of circumstances, factors and processes appearing along the transportation path of water from its sources to the root zone of the plant. Water efficiency of agricultural irrigation is connected with variety of circumstances, the impacts and the processes occurring during the transportation of water from water sources to plant root zone. Agrohydrological processes occur directly at the irrigated field, these processes linked to the infiltration of the applied water subsequent redistribution of the infiltrated water within the root zone. One of them are agrohydrological processes occurring directly on an irrigated field, connected with infiltration of water applied for irrigation to the soil, and the subsequent redistribution of infiltrated water in the root zone. These processes have the strongly pronounced spatial character depending on the one hand from a spatial variation of some hydrological characteristics of soils, and from other hand with distribution of volume of irrigation water on a surface of the area of an irrigated field closely linked with irrigation technology used. The combination of water application parameters with agrohydrological characteristics of soils and agricultural vegetation in each point at the surface of an irrigated field leads to formation of a vector field of intensity of irrigation water. In an ideal situation, such velocity field on a soil surface should represent uniform set of vertically directed collinear vectors. Thus values of these vectors should be equal to infiltration intensities of water inflows on a soil surface. In soil profile the field of formed intensities of a water flow should lead to formation in it of a water storage accessible to root system of irrigated crops. In practice this ideal scheme undergoes a lot of changes. These changes have the different nature, the reasons of occurrence and degree of influence on the processes connected with formation of water flow and water storage. The major changes are formed as a result of imposing of the intensity fields on a soil surface and its field capillary infiltration rate. Excess of the first intensity over the second in each point of soil surface leads to formation of a layer of intensity of water not infiltrated in soil. Thus generate the new field of vectors of intensity which can consist of vertically directed vector of speed of evaporation, a quasi horizontal vector of intensity of a surface water flow and quasi vertical vector of intensity of a preferential flow directed downwards. Principal cause of excess of irrigation water application intensity over capillary infiltration rate can be on the one hand spatial non-uniformity of irrigation water application, and with other spatial variability of capillary infiltration rate, connected with spatial variability of water storage in the top layers of soil. As a result the spatial redistribution of irrigation water over irrigated filed forms distortions of ideal model of irrigation water storage in root zone of soil profile. The major differences consist in increasing of water storage in the depressions of a relief of an irrigated field and accordingly in their reduction on elevated zones of a relief, as well as losses of irrigation water outside of boundaries of a root zone of an irrigated field, in vertical, and horizontal directions. One of key parameters characterizing interaction between irrigation technology and soil state an irrigated field are intensity of water application, intensity and volume of a capillary infiltration, the water storage in root zone at the moment of infiltration starting and a topography of an irrigated field. Fnalyzing of spatial links between these characteristics a special research had been carried out on irrigated by sprinkler machine called Fregate at alfalfa field during the summer of 2012. This research carried out at experimental farm of the research institute VolgNIIGiM situated at a left bank of Volga River of Saratov Region of Russia (N51.384650°, E46.055890°). The digital elevation model of soil surface has been created, as well as monitoring of spatial water storage with EM 38 device and of a biomass were carried out. Layers of corresponding spatial data have been created and analyzed. The carried out analysis of spatial regresses has shown presence of links between productivity of a biomass of a alfalfa, water storage and topography. The obtained results shows the significance to include spatial characteristics of the topography and water storage to the irrigation models, as well as adaptation of sprinkler technology to allow differentiate the volume and rate of the applied water within the field. Special attention should be done to quantify relationships between uniform technology of water application by sprinkler and spatial nonuniformity of moisture storage (zoning of high soil moisture in depressions) in soil and as consequence of infiltration capacity.

Unconfined aquifer response to infiltration basins and shallow pump tests

NASA Astrophysics Data System (ADS)

Ostendorf, David W.; DeGroot, Don J.; Hinlein, Erich S.

2007-05-01

SummaryWe measure and model the unsteady, axisymmetric response of an unconfined aquifer to delayed, arbitrary recharge. Water table drainage follows the initial elastic aquifer response, as modeled for uniform, instantaneous recharge by Zlotnik and Ledder [Zlotnik, V., Ledder, G., 1992. Groundwater flow in a compressible unconfined aquifer with uniform circular recharge. Water Resources Research 28(6), 1619-1630] and delayed drainage by Moench [Moench, A.F., 1995. Combining the Neuman and Boulton models for flow to a well in an unconfined aquifer. Ground Water 33(3), 378-384]. We extend their analyses with a convolution integral that models the delayed response of an aquifer to infiltration from a circular infiltration basin. The basin routes the hydrograph to the water table with a decay constant dependent on a Brooks and Corey [Brooks, R.H., Corey, A.T., 1966. Properties of porous media affecting fluid flow. Journal of the Irrigation and Drainage Division ASCE 92(2), 61-88] unsaturated permeability exponent. The resulting closed form model approaches Neuman's [Neuman, S.P., 1972. Theory of flow in unconfined aquifers considering delayed response of the water table. Water Resources Research 8(4), 1031-1045] partially penetrating pump test equation for a small source radius, instantaneous, uniform drainage and a shallow screen section. Irrigation pump data at a well characterized part of the Plymouth-Carver Aquifer in southeastern Massachusetts calibrate the small source model, while infiltration data from the closed drainage system of State Route 25 calibrate the infiltration basin model. The calibrated permeability, elasticity, specific yield, and permeability exponent are plausible and consistent for the pump and infiltration data sets.

Assessing the fate of organic micropollutants during riverbank filtration utilizing field studies and laboratory test systems

NASA Astrophysics Data System (ADS)

Schmidt, C. K.; Lange, F. T.; Sacher, F.; Baus, C.; Brauch, H.-J.

2003-04-01

In Germany and other highly populated countries, several waterworks use riverbank filtration as a first step in the treatment of river water for water supplies. Unfortunately, industrial and municipal discharges and the influence of agriculture lead to the pollution of rivers and lakes by a number of organic chemicals. In order to assess the impact of those organic micropollutants on the quality of drinking water, it is necessary to clarify their fate during infiltration and underground passage. The fate of organic micropollutants in a river water-groundwater infiltration system is mainly determined by adsorption mechanisms and biological transformations. One possibility to simulate the microbial degradation of single compounds during riverbank filtration is the use of laboratory test filter systems, that are operated as biological fixed-bed reactors under aerobic conditions. The benefit and meaningfulness of those test filters was evaluated on the basis of selected target compounds by comparing the results derived from test filter experiments with field studies under environmental conditions at the River Rhine. Samples from the river and from groundwater of a well characterized aerobic infiltration pathway were analyzed over a time period of several years for a spectrum of organic micropollutants. Target compounds comprised several contaminants relevant for the aquatic environment, such as complexing agents, aromatic sulfonates, pharmaceuticals (including iodinated X ray contrast media), and MTBE. Furthermore, the behaviour of some target compounds during aerobic riverbank filtration was compared to their fate along a section of an anaerobic (oxygen-depleted) aquifer at the River Ruhr that is characterized by a transition state between sulfate reduction and methane production. While some organic micropollutants showed no major differences, the elimination of others turned out to be clearly dependent on the underlying redox processes in the groundwater. The observations demonstrate, that levels of many organic micropollutants present in natural river waters can be reduced or even eliminated during aerobic and anaerobic bankfiltration. As such, the water quality is improved and subsequent treatment steps, such as granular activated carbon filtration, may be supported and simplified leading to decreased water treatment costs. Test filter experiments are a suitable tool to predict the extent of elimination of emerging organic contaminants during aerobic bankfiltration.

Documentation of Computer Program INFIL3.0 - A Distributed-Parameter Watershed Model to Estimate Net Infiltration Below the Root Zone

USGS Publications Warehouse

,

2008-01-01

This report documents the computer program INFIL3.0, which is a grid-based, distributed-parameter, deterministic water-balance watershed model that calculates the temporal and spatial distribution of daily net infiltration of water across the lower boundary of the root zone. The bottom of the root zone is the estimated maximum depth below ground surface affected by evapotranspiration. In many field applications, net infiltration below the bottom of the root zone can be assumed to equal net recharge to an underlying water-table aquifer. The daily water balance simulated by INFIL3.0 includes precipitation as either rain or snow; snowfall accumulation, sublimation, and snowmelt; infiltration into the root zone; evapotranspiration from the root zone; drainage and water-content redistribution within the root-zone profile; surface-water runoff from, and run-on to, adjacent grid cells; and net infiltration across the bottom of the root zone. The water-balance model uses daily climate records of precipitation and air temperature and a spatially distributed representation of drainage-basin characteristics defined by topography, geology, soils, and vegetation to simulate daily net infiltration at all locations, including stream channels with intermittent streamflow in response to runoff from rain and snowmelt. The model does not simulate streamflow originating as ground-water discharge. Drainage-basin characteristics are represented in the model by a set of spatially distributed input variables uniquely assigned to each grid cell of a model grid. The report provides a description of the conceptual model of net infiltration on which the INFIL3.0 computer code is based and a detailed discussion of the methods by which INFIL3.0 simulates the net-infiltration process. The report also includes instructions for preparing input files necessary for an INFIL3.0 simulation, a description of the output files that are created as part of an INFIL3.0 simulation, and a sample problem that illustrates application of the code to a field setting. Brief descriptions of the main program routine and of each of the modules and subroutines of the INFIL3.0 code, as well as definitions of the variables used in each subroutine, are provided in an appendix.

Analytical Analyses of Spatial and Temporal Characteristics of Infiltrated Water for Managed Aquifer Recharge

NASA Astrophysics Data System (ADS)

Zlotnik, V. A.; Ledder, G.; Kacimov, A. R.

2014-12-01

Disposal of excessive runoff or treated sewage into wadis and ephemeral streams is a common practice and an important hydrological problem in many Middle Eastern countries. While chemical and biological properties of the injected treated wastewater may be different from those of the receiving aquifer, the density contrast between the two fluids can be small. Therefore, studies of the fluid interface for variable density fluids or water intrusion are not directly relevant in many Managed Aquifer Recharge (MAR) problems. Other factors, such as the transient nature of injection and lack of detailed aquifer information must be considered. The disposed water reaching the water table through the vadose zone creates groundwater mounds, deforms the original water table, and develops finite-size convex-concave lenses of treated water over receiving water. After cessation of infiltration, these mounds flatten, water levels become horizontal, and infiltrated water becomes fully embedded in the receiving aquifer. The shape of the treated water body is controlled by the aquifer parameters, the magnitude of ambient flow, and the duration, rate, and cyclicity of infiltration. In case of limited aquifer data, advective transport modeling offers the most appropriate tools for predicting plume shapes over time, but surprisingly little work has been done on this important 3D flow problem. We investigate the lateral and vertical spreading of infiltrated water combining techniques of spatial velocity analyses by Zlotnik and Ledder (1992, 1993) with particle tracking. This approach allows for evaluating the geometry of the plume and the protection zone, the flow development phases, and other temporal and spatial effects and results can be used in conditions of limited data availability and quality. (Funding was provided by the USAID, DAI Subcontract 1001624-12S-19745)

Soil physical and hydrological properties under three biofuel crops in Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonin, Catherine; Lal, Dr. Rattan; Schmitz, Matthias

While biofuel crops are widely studied and compared for their energy and carbon footprints, less is known about their effects on other soil properties, particularly hydrologic characteristics. Soils under three biofuel crops, corn (Zea mays), switchgrass (Panicum virgatum), and willow (Salix spp.), were analyzed seven years after establishment to assess the effects on soil bulk density ({rho}{sub b}), penetration resistance (PR), water-holding capacity, and infiltration characteristics. The PR was the highest under corn, along with the lowest associated water content, while PR was 50-60% lower under switchgrass. In accordance with PR data, surface (0-10 cm) bulk density also tended tomore » be lower under switchgrass. Both water infiltration rates and cumulative infiltration amounts varied widely among and within the three crops. Because the Philip model did not fit the data, results were analyzed using the Kostiakov model instead. Switchgrass plots had an average cumulative infiltration of 69 cm over 3 hours with a constant infiltration rate of 0.28 cm min{sup -1}, compared with 37 cm and 0.11 cm min{sup -1} for corn, and 26 cm and 0.06 cm min{sup -1} for willow, respectively. Results suggest that significant changes in soil physical and hydrologic properties may require more time to develop. Soils under switchgrass may have lower surface bulk density, higher field water capacity, and a more rapid water infiltration rate than those under corn or willow.« less

Early formation of preferential flow in a homogeneous snowpack observed by micro-CT

NASA Astrophysics Data System (ADS)

Avanzi, Francesco; Petrucci, Giacomo; Matzl, Margret; Schneebeli, Martin; De Michele, Carlo

2017-05-01

We performed X-ray microtomographic observations of wet-snow metamorphism during controlled continuous melting and melt-freeze events in the laboratory. Three blocks of snow were sieved into boxes and subjected to cyclic, superficial heating or heating-cooling to reproduce vertical water infiltration patterns in snow similarly to natural conditions. Periodically, samples were taken at different heights and scanned. Results suggest that wet-snow metamorphism dynamics are highly heterogeneous even in an initially homogeneous snowpack. Consistent with previous work, we observed an increase with time in the thickness of the ice structure, which is a measure of grain size. However, this was coupled with large temporal scatter between consecutive measurements of the specific surface area and of the statistical moments of grain thickness distributions. Because of marked differences in the right tail, grain thickness distributions did not show shape invariance with time, contrary to previous analyses. In our experiments, wet-snow metamorphism showed two strikingly different patterns: homogeneous coarsening superimposed by faster heterogeneous coarsening in areas that were affected by preferential percolation of water. Liquid water movement in snow and fast structural evolution may be thus intrinsically coupled by early formation of preferential flow at local scale. These observations suggest that further experiments are highly needed to fully understand wet-snow metamorphism and infiltration patterns in a natural snowpack.

Application of a groundwater flow model for real-time well field management - lessons learned

NASA Astrophysics Data System (ADS)

Marti, B.; Kaiser, H.-P.; Kuhlmann, U.; Hendricks Franssen, H.-J.; Kinzelbach, W.

2012-04-01

The Hardhof well field, which lies in the city of Zurich, Switzerland, provides roughly 15 % of the towns drinking water demand from the Limmat valley aquifer. Groundwater and river filtrate are withdrawn in four large horizontal wells, each with a capacity of up to 48'000 m3 per day. The well field is threatened by potential pollution from leachate of a nearby land fill, possible accidents on the adjacent rail and road lines, and by diffuse pollution from former industrial sites and sewers located upstream of the well field. A line of recharge wells and basins forms a hydraulic barrier against the potentially contaminated water and increases the capacity of the well field. Currently, a genetic algorithm coupled to a 3-dimensional groundwater flow model is applied at the well field to determine optimal infiltration rates on a daily basis. This real-time control is based on particle backtracking in a quasi-stationary flow field. It estimates the origin of the water in the four horizontal wells and calculates the amount of potentially contaminated water in each well. Running the model iteratively and refining the parameters of the genetic algorithm at the end of each step yields the recommended daily infiltration rates. The current model accurately predicts the change of piezometric head due to changes in the river stage. However, during periods of large abstraction rates, the model underestimates the piezometric heads in the Hardhof area. In addition, the infiltration rates suggested by the control do not always agree with the experience of the Zurich water works (e.g. during periods with large abstraction rates) and hence the actually applied infiltration rates are sometimes chosen differently from the calculated ones. This work analyzes the performance of the model and the control during the year 2011. The computed heads of the on-line model are compared to the measured piezometric heads in over 80 measurement locations in the model area. Furthermore, differences between the computed management decisions and the actual management decisions are analyzed and suggestions for an improved management are made.

Artificial recharge of groundwater through sprinkling infiltration: impacts on forest soil and the nutrient status and growth of Scots pine.

PubMed

Nöjd, Pekka; Lindroos, Antti-Jussi; Smolander, Aino; Derome, John; Lumme, Ilari; Helmisaari, Heljä-Sisko

2009-05-01

We studied the chemical changes in forest soil and the effects on Scots pine trees caused by continuous sprinkling infiltration over a period of two years, followed by a recovery period of two years. Infiltration increased the water input onto the forest soil by a factor of approximately 1000. After one year of infiltration, the pH of the organic layer had risen from about 4.0 to 6.7. The NH(4)-N concentration in the organic layer increased, most probably due to the NH(4) ions in the infiltration water, as the net N mineralization rate did not increase. Sprinkling infiltration initiated nitrification in the mineral soil. Macronutrient concentrations generally increased in the organic layer and mineral soil. An exception, however, was the concentration of extractable phosphorus, which decreased strongly during the infiltration period and did not show a recovery within two years. The NO(3)-N and K concentrations had reverted back to their initial level during the two-year recovery period, while the concentrations of Ca, Mg and NH(4)-N were still elevated. Nutrient concentrations in the pine needles increased on the infiltrated plots. However, the needle P concentration increased, despite the decrease in plant-available P in the soil. Despite the increase in the nutrient status, there were some visible signs of chlorosis in the current-year needles after two years of infiltration. The radial growth of the pines more than doubled on the infiltrated plots, which suggests that the very large increase in the water input onto the forest floor had no adverse effect on the functioning of the trees. However, a monitoring period of four years is not sufficient for detecting potential long term detrimental effects on forest trees.

Adsorption and transport of As (V) in soil columns: Effect of As concentration, pH and sediment properties

USDA-ARS?s Scientific Manuscript database

It has been proposed that ground water contaminated with low concentrations of As (V) be remediated by infiltration and recharge into infiltration basins using the subsurface materials to adsorb the metal. This low cost remediation scheme allows for production of water that meets the drinking water ...

Thermal and hydraulic considerations regarding the fate of water discharged by the outflow channels to the Martian northern plains

NASA Technical Reports Server (NTRS)

Clifford, S. M.

1993-01-01

The identification of possible shorelines in the Martian northern plains suggests that the water discharged by the circum-Chryse outflow channels may have led to the formation of transient seas, or possibly even an ocean, covering as much as one-third of the planet. Speculations regarding the possible fate of this water have included local ponding and reinfiltration into the crust; freezing, sublimation, and eventual cold-trapping at higher latitudes; or the in situ survival of this now frozen water to the present day -- perhaps aided by burial beneath a protective cover of eolian sediment or lavas. Although neither cold-trapping at higher latitudes nor the subsequent freezing and burial of flood waters can be ruled out, thermal and hydraulic considerations effectively eliminate the possibility that any significant reassimilation of this water by local infiltration has occurred given climatic conditions resembling those of today. The arguments against the local infiltration of flood water into the northern plains are two-fold. First, given the climatic and geothermal conditions that are thought to have prevailed on Mars during the Late Hesperian (the period of peak outflow channel activity in the northern plains), the thickness of the cryosphere in Chryse Planitia is likely to have exceeded 1 km. A necessary precondition for the widespread occurrence of groundwater is that the thermodynamic sink represented by the cryosphere must already be saturated with ice. For this reason, the ice-saturated cryosphere acts as an impermeable barrier that effectively precludes the local resupply of subpermafrost groundwater by the infiltration of water discharged to the surface by catastraphic floods. Note that the problem of local infiltration is not significantly improved even if the cryosphere were initially dry, for as water attempts to infiltrate the cold, dry crust, it will quickly freeze, creating a seal that prevents any further infiltration from the ponded water above. The second argument against the local infiltration of flood water in the northern plains is based on hydraulic considerations. Repeated impacts have likely brecciated the Martian crust down to a depth of roughly 10 km. Given a value of permeability no greater than that inferred for the top 10 km of the Earth's crust (approximately 10(exp -2) darcies), a timescale as much as a billion years or more for the Martian groundwater system to achieve hydrostatic equilibrium, and the approximately 2-4 km elevation difference between the outflow channel source regions and the northern plains, the water confined beneath the frozen crust of the northern plains should have been under a significant hydraulic head. Thus, the existence of a hydraulic pathway between the ponded flood waters above the northern plains and the confined aquifer lying beneath it would not have led to the infiltration of flood water back into the crust, but rather the additional expulsion of groundwater onto the surface.

PILOT-SCALE EVALUATION OF ENGINEERED BARIER SYSTEMS FOR THE YUCCA MOUNTAIN PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.W. Webb; J.T. George; R.E. Finley

This paper describes two quarter-scale experiments (1.4 m diameter) and associated numerical analyses on granular backfill engineered barrier systems in support of the Yucca Mountain Project for the potential repository. The two configurations include a sloped capillary barrier and a plain backfill. The tests involve application of dyed water as a constant line infiltration source along the top of the test set-up, monitoring water movement through the test, and measuring water exiting the experiments. A complete water balance estimate is made for each test, and observed water movement is compared with (1) detailed numerical analyses conducted using the TOUGH2 codemore » for unsaturated flow in porous media and (2) posttest observations. The results of the testing and analyses show that for the injection rates and configuration applied, the capillary barrier design diverts a significant amount of all injected water and the TOUGH2 pretest predictions show qualitative and quantitative agreement with the experimental data.« less

40 CFR 440.143 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... an open-cut mine plant site shall not exceed the volume of infiltration, drainage and mine drainage... of infiltration, drainage and mine drainage waters which is in excess of the make up water required...

40 CFR 440.143 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... an open-cut mine plant site shall not exceed the volume of infiltration, drainage and mine drainage... of infiltration, drainage and mine drainage waters which is in excess of the make up water required...

Simulating Heterogeneous Infiltration and Contaminant leaching Processes at Chalk River, Ontario

NASA Astrophysics Data System (ADS)

Ali, M. A.; Ireson, A. M.; Keim, D.

2015-12-01

A study is conducted at a waste management area in Chalk River, Ontario to characterize flow and contaminant transport with the aim of contributing to improved hydrogeological risk assessment in the context of waste management. Field monitoring has been performed to gain insights into the unsaturated zone characteristics, moisture dynamics, and contaminant transport rates. The objective is to provide quantitative estimates of surface fluxes (quantification of infiltration and evaporation) and investigations of unsaturated zone processes controlling water infiltration and spatial variability in head distributions and flow rates. One particular issue is to examine the effectiveness of the clayey soil cap installed to prevent infiltration of water into the waste repository and the top sand soil cover above the clayey layer to divert the infiltrated water laterally. The spatial variability in the unsaturated zone properties and associated effects on water flow and contaminant transport observed at the site, have led to a concerted effort to develop improved model of flow and transport based on stochastic concepts. Results obtained through the unsaturated zone model investigations are combined with the hydrogeological and geochemical components and develop predictive tools to assess the long term fate of the contaminants at the waste management site.

Relaxation of water infiltration pulses observed with GPR

NASA Astrophysics Data System (ADS)

Hantschel, Lisa; Hemmer, Benedikt; Roth, Kurt

2017-04-01

We observe the relaxation of infiltration pulses in sandy soil with ground-penetrating radar (GPR). The spatial distribution of water in the infiltration area and its temporal evolution is represented by ordinary reflections at layer boundaries as well as multiple reflections at the wetting front and the pulse boundaries. The structure of these highly resolved signals are reproduced by numerical simulations of electromagnetic wave propagation. The temporally highly resolved electrical fields reveal the origin also of complex reflection signals. The usage of these more complex signals might allow a more detailed representation of the infiltration process by direct analysis as well as in combination with inversion techniques.

Forward modeling to investigate inversion artifacts resulting from time-lapse electrical resistivity tomography during rainfall simulations

NASA Astrophysics Data System (ADS)

Carey, Austin M.; Paige, Ginger B.; Carr, Bradley J.; Dogan, Mine

2017-10-01

Time-lapse electrical resistivity tomography (ERT) is commonly used as a minimally invasive tool to study infiltration processes. In 2014, we conducted field studies coupling variable intensity rainfall simulation with high-resolution ERT to study the real-time partitioning of rainfall into surface and subsurface response. The significant contrast in resistivity in the subsurface from large changes in subsurface moisture resulted in artifacts during the inversion process of the time-lapse ERT data collected using a dipole-dipole electrode array. These artifacts, which are not representative of real subsurface moisture dynamics, have been shown to arise during time-lapse inversion of ERT data and may be subject to misinterpretation. Forward modeling of the infiltration process post field experiments using a two-layer system (saprolite overlain by a soil layer) was used to generate synthetic datasets. The synthetic data were used to investigate the influence of both changes in volumetric moisture content and electrode configuration on the development of the artifacts identified in the field datasets. For the dipole-dipole array, we found that a decrease in the resistivity of the bottom layer by 67% resulted in a 50% reduction in artifact development. Artifacts for the seven additional array configurations tested, ranged from a 19% increase in artifact development (using an extended dipole-dipole array) to as much as a 96% decrease in artifact development (using a wenner-alpha array), compared to that of the dipole-dipole array. Moreover, these arrays varied in their ability to accurately delineate the infiltration front. Model results showed that the modified pole-dipole array was able to accurately image the infiltration zone and presented fewer artifacts for our experiments. In this study, we identify an optimal array type for imaging rainfall-infiltration dynamics that reduces artifacts. The influence of moisture contrast between the infiltrating water and the bulk subsurface material was characterized and shown to be a major factor in contributing to artifact development. Through forward modeling, this study highlights the importance of considering array type and subsurface moisture conditions when using time-lapse resistivity to obtain reliable estimates of vadose zone flow processes during rainfall-infiltration events.

RUNON a hitherto little noticed factor - Field experiments comparing RUNOFF/RUNON processes

NASA Astrophysics Data System (ADS)

Kohl, Bernhard; Achleitner, Stefan; Lumassegger, Simon

2017-04-01

When ponded water moves downslope as overland flow, an important process called runon manifests itself, but is often ignored in rainfall-runoff studies (Nahar et al. 2004) linking infiltration exclusively to rainfall. Runon effects on infiltration have not yet or only scarcely been evaluated (e.g. Zheng et al. 2000). Runoff-runon occurs when spatially variable infiltration capacities result in runoff generated in one location potentially infiltrating further downslope in an area with higher infiltration capacity (Jones et al. 2013). Numerous studies report inverse relationships between unit area volumes of overland flow and plot lengths (Jones et al. 2016). This is an indication that the effects of rainfall and runon often become blurred. We use a coupled hydrological/2D hydrodynamic model to simulate surface runoff and pluvial flooding including the associated infiltration process. In frame of the research project SAFFER-CC (sensitivity assessment of critical condition for local flash floods - evaluating the recurrence under climate change) the influence of land use and soil conservation on pluvial flash flood modeling is assessed. Field experiments are carried out with a portable irrigation spray installation at different locations with a plot size 5m width and 10m length. The test plots were subjected first to a rainfall with constant intensity of 100 mm/h for one hour. Consecutively a super intense, one hour mid accentuated rainfall hydrograph was applied after 30 minutes at the same plots, ranging from 50 mm/h to 200 mm/h for 1hour. Finally, runon was simulated by upstream feeding of the test plots using two different inflow intensities. The irrigation test showed expected differences of runoff coefficients depending on the various agricultural management. However, these runoff coefficients change with the applied process (rainfall or runon). While a decrease was observed on a plot with a closed litter layer, runoff coefficient from runon increases on poor covered plots. At the same time, a similar variety in the characteristics of the infiltration behavior between rainfall and runoff could be observed. This extension of artificial rainfall simulations with concurrent and successive runon tests will enhance our process understanding.

Numerical analysis of groundwater recharge through stony soils using limited data

NASA Astrophysics Data System (ADS)

Hendrickx, J. M. H.; Khan, A. S.; Bannink, M. H.; Birch, D.; Kidd, C.

1991-10-01

This study evaluates groundwater recharge on an alluvial fan in Quetta Valley (Baluchistan, Pakistan), through deep stony soils with limited data of soil texture, soil profile descriptions, water-table depths and meteorological variables. From the soil profile descriptions, a representative profile was constructed with typical soil layers. Next, the texture of each layer was compared with textures of soils with known soil physical characteristics; it is assumed that soils from the same textural class have similar water retention and hydraulic conductivity curves. Finally, the water retention and hydraulic conductivity curves were transformed to account for the volume of stones in each layer; this varied between 0 and 60 vol. %. These data were used in a transient finite difference model and in a steady-state analytical solution to evaluate the travel time of the recharge water and the maximum annual recharge volume. Travel times proved to be less sensitive to differences in soil physical characteristics than to differences in annual infiltration rates. Therefore, estimation of soil physical characteristics from soil texture data alone appears justified for this study. Estimated travel times on the alluvial fan in the Quetta Valley vary between 1.6 years, through a soil profile of 25 m with an infiltration rate of 120 cm year -1, to 18.3 years through a soil profile of 100 m with an infiltration rate of 40 cm year -1. When the infiltration rate of the soil exceeds 40 cm day -1, the infiltration process proceeds so fast that evaporation losses are small. If the depth of ponding at the start of infiltration is more than 1 m, at least 90% of the applied recharge water will reach the water table, providing that the ponding area is bare of vegetation.

Laboratory simulated transport of microcystin-LR and cylindrospermopsin in groundwater under the influence of stormwater ponds: implications for harvesting of infiltrated stormwater

USGS Publications Warehouse

O'Reilly, Andrew M.; Wanielista, Martin P.; Loftin, Keith A.; Chang, Ni-Bin; Schirmer, Mario; Hoehn, Eduard; Vogt, Tobias

2011-01-01

Water shortages in the southeastern United States have led to a need for more intensive management and usage of stormwater for beneficial uses such as irrigation. Harvesting of infiltrated stormwater from horizontal wells in sandy aquifer sediments beneath stormwater ponds has emerged as an alternative in need of evaluation. Cyanobacteria may proliferate in stormwater ponds; cyanotoxins produced by these organisms represent potential public health concerns. Results of two, saturated flow, sand column experiments indicate breakthrough of microcystin-LR (MCLR) and cylindrospermopsin (CYL) within 1―2 pore volumes indicating little removal attributable to sorption. Concentration-based MCLR removal efficiencies up to 90% were achieved, which we hypothesize were predominantly due to biodegradation. In contrast, CYL removal efficiencies were generally less than 15%. On the basis of these results, removal of sandy soil in the stormwater pond bottom and addition of sorption media with greater binding affinities to cyanotoxins may enhance natural attenuation processes prior to water withdrawal.

Infiltration and recharge at Sand Hollow, an upland bedrock basin in southwestern Utah: Chapter I in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Heilweil, Victor M.; Solomon, D. Kip; Gardner, Philip M.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

Permeable bedrock aquifers in arid regions of the southwestern United States are being used increasingly as a source of water for rapidly growing populations, yet in many areas little is known about recharge processes and amounts available for sustainable development. Environmental tracers were used in this study to investigate infiltration and recharge to the Navajo Sandstone at Sand Hollow in the eastern Mojave Desert of southwestern Utah. Average annual precipitation is about 210 millimeters per year. Tracers included bromide, chloride, deuterium, oxygen-18, and tritium. The basin-wide average recharge rate, based on ground-water chloride mass balance, is about 8 millimeters per year, or 4 percent of precipitation. However, infiltration and recharge are highly variable spatially within Sand Hollow. Recharge primarily occurs both as focused infiltration of runoff from areas of outcropping bedrock and as direct infiltration beneath coarse surficial soils. Locations with higher rates generally have lower vadose-zone and ground-water chloride concentrations, smaller vadose-zone oxygen-18 evaporative shifts, and higher ground-water tritium concentrations. Infiltration rates estimated from vadose-zone tritium concentrations at borehole sites within Sand Hollow range from 1 to more than 57 millimeters per year; rates calculated from average vadose-zone chloride concentrations between land surface and the bottom of the chloride bulge range from 0 to 9 millimeters per year; rates calculated from average vadose-zone chloride concentrations below the chloride bulge range from 0.5 to 15 millimeters per year; and rates calculated from ground-water chloride concentrations range from 3 to 60 millimeters per year. A two-end-member deuterium-mixing model indicates that about 85 percent of ground-water recharge in Sand Hollow occurs in the 50 percent of the basin covered by coarser soils and bedrock. Vadose-zone chloride concentrations at individual boreholes represent as much as 12,000 years of accumulation, whereas vadose-zone tritium has only been accumulating during the past 50 years. Environmental tracers at Sand Hollow indicate the possibility of a cyclical recharge pattern from higher infiltration rates earlier in the Holocene to lower rates later in the Holocene, back again to higher infiltration rates during the past 50 years.

Modelling spatial distribution of soil steady state infiltration rate in an urban park (Vingis Parkas, Vilnius, Lithuania)

NASA Astrophysics Data System (ADS)

Pereira, Paulo; Cerda, Artemi; Depellegrin, Daniel; Misiune, Ieva; Bogunovic, Igor; Menchov, Oleksandr

2016-04-01

Within the hydrological process, infiltration is a key component as control the partitioning of the rainfall into runoff or soil water (Cerdà, 1997). And the infiltration process is determining the fate of the soil development and the human impact in the soil system (Brevik et al., 2015). On forest soils, the infiltration use to be high due to the macropore flow, which drainages the surface runoff usually generated by the hydrophobic response of soil reach in organic matter (Hewelke et al., 2015) or as a consequence of forest fires (Jordán et al., 2010; Pereira et al., 2014) due to the development of water repellent substances (Mao et al., 2015), which are mainly associated to the ash (Pereira et al., 2014; Pereira et al., 2015). To understand the role the infiltration plays in the soil development and the runoff generation is important, and also is necessary to understand how some factors such as vegetation, crust, stones, litter, mulches… play in the hydrological, erosional and pedological system (Cerdà, 2001; Keesstra, 2007; Liu et al., 2014; Bisantino et al., 2015; Cassinari et al., 2015, Cerdà et al., 2015; Mohawesh et al., 2015; Terribile et al., 2015). The well-know importance of the infiltration process did not resulted in the research on the infiltration on urban areas, although there is where the infiltration is more altered. Water infiltration is extremely important in urbanized areas, since the majority of the surfaces are sealed by concrete, asphalt and other materials. Soil sealing increases exponentially the impacts of flash floods and reduces soil infiltration capacity. This decreases importantly one of the most important services provided by soil: water storage and infiltration. In this context, the existence of green areas and urban parks are of major importance to mitigate the impact of human settlements in soil water infiltration. The aim of this work is to assess the spatial distribution of steady-state soil water infiltration in the larger urban park in Vilnius, Vinguis Parkas. The studied area is located near the Neris River and occupies an area of approximately 162 hectares. Inside the park a total of 95 randomly points were selected to measure soil steady infiltration, between April and September of 2016. At each sampling point, 4 infiltration measurements were carried out using a cylinder infiltrometer with 15 cm higher and a diameter of 7 cm (Cerda, 1996). Each experiment has the duration of 1 hour and the measurements of the infiltrated water were carried out 1, 2, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 and 60 minutes (Cerda, 1996). The steady state infiltration value of each sampling point corresponds to the average value of the 4 measurements. In each point, the 4 measurements were separated by 5 meters to take in account the spatial variability (Neris et al., 2013). In total 380 infiltration tests were carried out (95x4). Previous to data modelling, data normality was assessed using the shapiro wilk-test and homogeneity of the variances, using Levene test, respectively. The original data was not normally distributed and, only respected the Gaussian distribution and heteroscedasticity after a logarithmic transformation. Data modelling was carried out using transformed data. The accuracy of steady-state soil infiltration spatial distribution was carried out testing several interpolation methods, as Inverse Distance to a Weight (IDW) with the power of 1,2,3,4 and 5, Local Polynomial methods, with the power of 1 and 2 Radial Basis Functions - Spline With Tension (SPT), Completely Regularized Spline (CRS), Multiquadratic (MTQ), Inverse Multiquadratic (IMTQ) and Thin Plate Spline (TPS) - and Geostatistical methods as, Ordinary Kriging (OK), Simple Kriging (SK) and Universal Kriging (UK) (Pereira et al., 2015). Methods performance was assessed calculating the Root Square Mean Error (RMSE) from the errors obtained from cross-validation. The results showed that on average steady state infiltration rate was 69 mm h-1, with a minimum of 12.72 mm h-1 and a maximum of 692.31 mm h-1. The spatial variability was extremely high (coefficient of variation of 153.71). Among the methods tested the most accurate was SK (RMSE=0.542) and the least precise TPS (RMSE=0.695). With the exception of the IDW5, all the correlations between observed and estimated values were significant at a p<0.05. All the residuals followed the normal distribution. Steady state infiltration was high in the southern and central part of the plot (where the human impact is high) and low in the northern part of the park, where forests are denser. References Bisantino, T., Bingner, R., Chouaib, W., Gentile, F., Trisorio Liuzzi, G. (2015) Estimation of runoff, peak discharge and sediment load at the event scale in a medium-size mediterranean watershed using the annagnps model Land Degradation and Development, 26, 340-355. Brevik, E. C., Cerdà, A., Mataix-Solera, J., Pereg, L., Quinton, J. N., Six, J., Van Oost, K. (2015) The interdisciplinary nature of SOIL. SOIL, 1, 117-129. Cassinari, C., Manfredi, P., Giupponi, L., Trevisan, M., Piccini, C. (2015). Relationship between hydraulic properties and plant coverage of the closed-landfill soils in Piacenza (Po Valley, Italy). Solid Earth, 6, 929-943. Cerdà, A. (1996) Seasonal variability of infiltration rates under contrasting slope conditions in southeast Spain. Geoderma, 69, 217-232. Cerdà, A., González-Pelayo, O., Giménez-Morera, A., Jordán, A., Pereira, P., Novara, A., Brevik, E.C., Prosdocimi, M., Mahmoodabadi, M., Keesstra, S., García Orenes, F., Ritsema, C. (2015) The use of barley straw residues to avoid high erosion and runoff rates on persimmon plantations in Eastern Spain under low frequency - high magnitude simulated rainfall events. Soil Research (In press) Cerdà, A. (2001) Effects of rock fragment cover on soil infiltration, interrill runoff and erosion. European Journal of Soil Science, 52, 59-68. Cerdà, A. (1997) Seasonal changes of the infiltration rates in a mediterranean scrubland on limestone. Journal of Hydrology, 198, 209-225. Hewelke, E., Szatyłowicz, J., Gnatowski, T., Oleszczuk, R. (2015) Effects of soil water repellency on moisture patterns in a degraded sapric histosol, Land Degradation and Development, DOI: 10.1002/ldr.2305 Jordán, A., González, F.A., Zavala, L.M. (2010) Re-establishment of soil water repellency after destruction by intense burning in a Mediterranean heathland (SW Spain). Hydrological Processes, 24, 736-748. Keesstra, S.D. (2007) Impact of natural reforestation on floodplain sedimentation in the Dragonja basin, SW Slovenia. Earth Surface Processes and Landforms, 32, 49-65. Liu, Z., Yao, Z., Huang, H., Wu, S., Liu, G. (2014) Land use and climate changes and their impacts on runoff in the Yarlung Zangbo river basin, China. Land Degradation and Development, 25, 203-215. Mao, J., Nierop, K.G.J., Rietkerk, M., Dekker, S.C. (2015) Predicting soil water repellency using hydrophobic organic compounds and their vegetation origin. SOIL, 1, 411-425. Mohawesh, Y., Taimeh, A., Ziadat, F. (2015) Effects of land use changes and soil conservation intervention on soil properties as indicators for land degradation under a Mediterranean climate Solid Earth, 6, 857-868. Neris, J., Jimenez, C., Fuentes, J., Morillas, G., Tejedor, M. (2012) Vegetation and land-use effects on soil properties and water infiltration of Andisols in Tenerife (Canary Islands, Spain). Catena, 98, 55-62. Pereira, P., Cerda, A., Ubeda, X., Mataix-Solera, J., Arcenegui, V., Zavala, L. (2015) Modelling the impacts of wildfire on ash thickness in short-term period. Land Degradation and Development, 26, 180-192. Pereira, P., Úbeda, X., Martin, D., Mataix-Solera, J., Cerdà, A., Burguet, M. Wildfire effects on extractable elements in ash from a Pinus pinaster forest in Portugal (2014) Hydrological Processes, 28, 3681-3690. Pereira, P., Úbeda, X., Mataix-Solera, J., Oliva, M., Novara, A. (2014) Short-term changes in soil Munsell colour value, organic matter content and soil water repellency after a spring grassland fire in Lithuania. Solid Earth, 5, 209-225. Terribile, F., Agrillo, A., Bonfante, A., Buscemi, G., Colandrea, M., D'Antonio, A., De Mascellis, R., De Michele, C., Langella, G., Manna, P., Marotta, L., Mileti, F.A., Minieri, L., Orefice, N., Valentini, S., Vingiani, S., Basile, A. A (2015) Web-based spatial decision supporting system for land management and soil conservation. Solid Earth, 6, 903-928.

Infiltration and solute transport experiments in unsaturated sand and gravel, Cape Cod, Massachusetts: Experimental design and overview of results

USGS Publications Warehouse

Rudolph, David L.; Kachanoski , R. Gary; Celia, Michael A.; LeBlanc, Denis R.; Stevens, Jonathon H.

1996-01-01

A series of infiltration and tracer experiments was conducted in unsaturated sand and gravel deposits on Cape Cod, Massachusetts. A network of 112 porous cup lysimeters and 168 time domain reflectometry (TDR) probes was deployed at depths from 0.25 to 2.0 m below ground surface along the centerline of a 2-m by 10-m test plot. The test plot was irrigated at rates ranging from 7.9 to 37.0 cm h−1 through a sprinkler system. Transient and steady state water content distributions were monitored with the TDR probes and spatial properties of water content distributions were determined from the TDR data. The spatial variance of the water content tended to increase as the average water content increased. In addition, estimated horizontal correlation length scales for water content were significantly smaller than those estimated by previous investigators for saturated hydraulic conductivity. Under steady state flow conditions at each irrigation rate, a sodium chloride solution was released as a tracer at ground surface and tracked with both the lysimeter and TDR networks. Transect-averaged breakthrough curves at each monitoring depth were constructed both from solute concentrations measured in the water samples and flux concentrations inferred from the TDR measurements. Transport properties, including apparent solute velocities, dispersion coefficients, and total mass balances, were determined independently from both sets of breakthrough curves. The dispersion coefficients tended to increase with depth, reaching a constant value with the lysimeter data and appearing to increase continually with the TDR data. The variations with depth of the solute transport parameters, along with observations of water and solute mass balance and spatial distributions of water content, provide evidence of significant three-dimensional flow during the irrigation experiments. The TDR methods are shown to efficiently provide dense spatial and temporal data sets for both flow and solute transport in unsaturated sediments with minimal sediment and flow field disturbance. Combined implementation of lysimeters and TDR probes can enhance data interpretation particularly when three-dimensional flow conditions are anticipated.

Comparing dynamic recording of infiltration by X-Ray tomography to the results of a dual porosity model for structured soils

NASA Astrophysics Data System (ADS)

Lissy, Anne-Sophie; Sammartino, Stephane; Di Pietro, Liliana; Lecompte, François; Ruy, Stephane

2017-04-01

With climate change, preferential flow phenomenon in soil could be predominant in Mediterranean zone. Understanding this phenomenon becomes a fundamental issue for preserving the water resource in quantity (drinking water) and quality (pesticide content). Non-invasive imaging technics, as X-ray tomography, allow studying water infiltration in laboratory with time-lapse imaging to visualize preferential flow path in soil columns (Sammartino et al. 2012). The modeling of water flow with a dual porosity model (matrix and macropores) integrates these fast flow phenomena (Ilhem 2014). These models, however needs more explicit links with the soil structure. The comparison of experimental results of infiltration (dynamics images and mass data) and modeling could improve our comprehension of preferential flow phenomenon and allow a better integration of the functional macroporosity (i.e. which drains water infiltration during a rain event) in such mass transfer models (Sammartino et al. 2015). Soil columns (Ø 12 cm - hauteur 13 cm, clay-loamy & medium sandy loam) have been sampled in the field to preserve their structure (field plowed or not). Several rains have been simulated in the laboratory and the last one was performed in an X-ray medical scanner (Siemens Somatom® 128 slices) at the CIRE platform (INRA, Centre - Val de Loire). Total and functional macro porosities were identified from time lapse tridimensional images. Water dynamics in the porosities was characterized from the identification and analysis of voxels filled by water. With an image resolution of 350μm only water in the largest macropores can be identified. The modeling of these experiments was carried out via the VirtualSoil platform (UMR Emmah, Avignon; www6.inra.fr/vsoil) using a water flow model coupling Darcy-Richards and KDW equations (Di Pietro et al., 2003). The simulated water flux drained by macropores is similar to the experimental hydrograph obtained for rainfalls on soils close to the saturation. The model reproduced well the flow dynamics: (1) breakthrough time (arrival time of the first drop at the bottom of the column) and (2) the total drained water quantity. A sensitivity analysis of this model is in progress in order to determine the influence of each KDW parameters (two kinematic parameters and one dispersion parameter) and to probe where the functional soil structure could be accounted for in the model structure or in the model parameters. First results show that the kinematic parameters modify the breakthrough time and the slope of the drainage curve. Keywords: functional macroporosity, modeling, RX tomography, infiltration, Richards and KDW equations. Sammartino et al., 2012. A novel method to visualize and characterize preferential flow in undisturbed soil cores by using multislice helical CT. Vadose Zone Journal. Sammartino et Lissy, 2015. Identifying the functional macropore network related to preferential flow in structured soils, Vadose Zone Journal, vol. 14, no. 10. Di Pietro et al. 2003. Predicting preferential water flow in soils by traveling-dispersive waves. Journal of Hydrology (278), pp.64-75. Adel Ilhem (2014) - Modélisation des transferts d'eau dans les sols hétérogènes (internship report)

Low Impact Development in Army Construction

DTIC Science & Technology

2012-05-01

recycling , to reduce outdoor potable water consumption by a minimum of 50 percent over that consumed by conventional means (plant species and plant...Infiltration trenches • Subsurface infiltration beds • Bioretention • Level spreaders • Native revegetation • Pervious pavement with infiltration

Variation of Desert Soil Hydraulic Properties with Pedogenic Maturity

NASA Astrophysics Data System (ADS)

Nimmo, J. R.; Perkins, K. S.; Mirus, B. B.; Schmidt, K. M.; Miller, D. M.; Stock, J. D.; Singha, K.

2006-12-01

Older alluvial desert soils exhibit greater pedogenic maturity, having more distinct desert pavements, vesicular (Av) horizons, and more pronounced stratification from processes such as illuviation and salt accumulation. These and related effects strongly influence the soil hydraulic properties. Older soils have been observed to have lower saturated hydraulic conductivity, and possibly greater capacity to retain water, but the quantitative effect of specific pedogenic features on the soil water retention or unsaturated hydraulic conductivity (K) curves is poorly known. With field infiltration/redistribution experiments on three different-aged soils developed within alluvial wash deposits in the Mojave National Preserve, we evaluated effective hydraulic properties over a scale of several m horizontally and to 1.5 m depth. We then correlated these properties with pedogenic features. The selected soils are (1) recently deposited sediments, (2) a soil of early Holocene age, and (3) a highly developed soil of late Pleistocene age. In each experiment we ponded water in a 1-m-diameter infiltration ring for 2.3 hr. For several weeks we monitored subsurface water content and matric pressure using surface electrical resistance imaging, dielectric-constant probes, heat-dissipation probes, and tensiometers. Analysis of these data using an inverse modeling technique gives the water retention and K properties needed for predictive modeling. Some properties show a consistent trend with soil age. Progressively more developed surface and near-surface features such as desert pavement and Av horizons are the likely cause of an observed consistent decline of infiltration capacity with soil age. Other properties, such as vertical flow retardation by layer contrasts, appear to have a more complicated soil-age dependence. The wash deposits display distinct depositional layering that has a retarding effect on vertical flow, an effect that may be less pronounced in the older Holocene soil, where the original depositional structure has a relatively modest influence. Anisotropy at the scale of centimeters is of major importance in the Pleistocene soil, with developed horizons that tend to hold water within about 0.5 m of the surface for a longer duration than in the two younger soils. Correlation of these and related pedogenic features with soil hydraulic properties is a first step toward the estimation of effective hydraulic properties of widely varying Mojave Desert soils, as needed for large-scale evaluation of soil moisture dynamics in relation to ecological habitat quality.

A simulation of rainfall infiltration based on two-phase flow

NASA Astrophysics Data System (ADS)

Wang, Jun; Xi, Niannian; Liu, Gang; Hao, Shuang

2016-04-01

Rainfall infiltration in slope usually is one of major reasons cause landslide, which involves multiphase flow coupling with soil, water and gas. In order to study the mechanism of landslide caused by rainfall infiltration, a simulation of rainfall infiltration of DaPing slope, which locates in the Three Gorges Region of China, is presented based on the numerical solution of governing equations of two-phase flow in this paper. The results of this research suggest that there are two sections can be divided in the surface of slope, one is inflow area and the other is overflow area, according to where it is infiltration and discharge. The general inflow area is on the upside of slope, while the overflow area is on the underside. The middle section of slope is on a fluctuant position between inflow and overflow area, which is dramatically affected by the water content inside of slope. Moreover, the average rate of infiltration is more stable in both inflow and overflow area, whose numerical value is depend on the geometry and transmission characteristics of slope. And the factors of rainfall characteristics, surface flow and temperature have little effect on them. Furthermore, in the inflow area, when rainfall intensity is higher than infiltration the rain on the surface of slope will run off, otherwise water and gas will completely infiltrate through soil. The situation is different in the overflow area whose overland flow condition is depended on whether it is saturated or not inside of slope. When it is saturated in the slope, there is no infiltration in the overflow area. But when it is unsaturated, the infiltration intensity will equal to rainfall intensity. In a summary, the difference from inflow and overflow area is the evidence that the landslide may likely to happen on the slope of overflow area when it comes to a rainfall. It is disadvantageous for slope stability when transmitting the pressure of saturated water weight at the top of slope through the pore gas to groundwater, the groundwater pressure will increased sharply.

[Effects of biochar addition into soils in semiarid land on water infiltration under the condition of the same bulk density].

PubMed

Qi, Rui-Peng; Zhang, Lei; Yan, Yong-Hao; Wen, Man; Zheng, Ji-Yong

2014-08-01

Making clear the effects of biochar addition on soil water infiltration process can provide the scientific basis for the evaluation of the influence of biochar application on soil hydrology in semi-arid region. In this paper, through the soil column simulation method in laboratory, the effects of biochar of three sizes (1-2 mm, 0.25-1 mm and ≤ 0.25 mm) at 4 doses (10, 50, 100 and 150 g x kg(-1)) on the cumulative infiltration, the permeability and the stable infiltration rate of two different soils (anthrosol and aeolian sandy soil) were studied. The results showed that the infiltration capacity of the anthrosol was obviously increased compared to the control, however, the one in the aeolian sandy soil was decreased due to the biochar addition. At 100 minutes after infiltration starting, the averaged cumulative infiltration was increased by 25.1% in the anthrosol with comparison to the control. Contrarily, the averaged cumulative infiltration was decreased by 11.1% in the aeolian sandy soil at 15 minutes after infiltration starting. When the dose was the same, biochar with different particle sizes improved the infiltration for the anthrosol, but for the different dose treatments, the particle size of biochar which showed the greatest improvement was different. As for the aeolian sandy soil, the infiltration increased at the dose of 10 g x kg(-1) after the addition of biochar with different particle sizes, while decreased at the higher dose of 50, 100 and 150 g x kg(-1). The cumulative infiltration of the aeolian sandy soil was decreased with the increase in addition amount of biochar with the same particle size, while it was not so for the anthrosol. The determination coefficient fitted by the Philip infiltration model ranged from 0.965 to 0.999, suggesting this model was suitable for the simulation of soil water infiltration process after biochar application. Statistical analysis of main effects showed that the biochar particle size, the biochar addition amount, and the interactive effect had statistically significant effect on the soil permeability and stable infiltration rate in the two soils. In conclusion, the biochar had different effects on the soils with different textures, moreover, there was a positive correlation relationship between the impact and the addition amount.

Influence of seasonal climatic variability on shallow infiltration at Yucca Mountain

USGS Publications Warehouse

Hevesi, Joseph A.; Flint, Alan L.

1993-01-01

To analyze infiltration and the redistribution of moisture in alluvial deposits at Yucca Mountain, water content profiles at a 13.5 m deep borehole were measured at monthly intervals using a neutron moisture probe. Increases in water content to a maximum depth of 1.8 m in response to winter season precipitation were noted. Below a depth of 1.8 m, a gradual drying trend was indicated. A simulation study showed that, although small amounts of water may be percolating through the deep nonwetted ones of the profile, the influence of climatic variability on infiltration through thick alluvial deposits at Yucca Mountain is greatly mitigated by evapotranspiration.

Infiltration on sloping terrain and its role on runoff generation and slope stability

NASA Astrophysics Data System (ADS)

Loáiciga, Hugo A.; Johnson, J. Michael

2018-06-01

A modified Green-and-Ampt model is formulated to quantify infiltration on sloping terrain underlain by homogeneous soil wetted by surficial water application. This paper's theory for quantifying infiltration relies on the mathematical statement of the coupled partial differential equations (pdes) governing infiltration and runoff. These pdes are solved by employing an explicit finite-difference numerical method that yields the infiltration, the infiltration rate, the depth to the wetting front, the rate of runoff, and the depth of runoff everywhere on the slope during external wetting. Data inputs consist of a water application rate or the rainfall hyetograph of a storm of arbitrary duration, soil hydraulic characteristics and antecedent moisture, and the slope's hydraulic and geometric characteristics. The presented theory predicts the effect an advancing wetting front has on slope stability with respect to translational sliding. This paper's theory also develops the 1D pde governing suspended sediment transport and slope degradation caused by runoff influenced by infiltration. Three examples illustrate the application of the developed theory to calculate infiltration and runoff on a slope and their role on the stability of cohesive and cohesionless soils forming sloping terrain.

Modeling Integrated Cave Drip Recharge Data using DReAM (Daily Recharge Assessment Model) in a Dry Eastern Mediterranean Area, Sif Cave - Israel

NASA Astrophysics Data System (ADS)

Anker, Y.; Sheffer, N. A.; Scanlon, B. R.; Gimburg, A.; Morin, E.

2010-12-01

Understanding recharge mechanisms and controls in karst regions is extremely important for managing water resources because of the dynamic nature of the system. To better understand this mechanism, a cave in the recharge area of the karstic Western Mountain Aquifer (WMA) of Israel was equipped to measure precipitation infiltration (2006-2008) by collecting integrated water drips from three areas in the cave (14, 46, and 52 m2 areas). Barrels equipped with pressure transducers record drip rate and volume for each of the three areas and enable estimation of recharge. A water budget model - DReAM (Daily Recharge Assessment Model) was used to quantify and predict infiltration behavior at the cave. DReAM includes calculations of all water cycle components - precipitation, evapotranspiration, runoff and recharge. The model was calibrated and validated using two independent sets of values, providing good agreement between calculated and observed data. Modeling results agree with previous studies that show: 1) three distinct flow paths (slow, intermediate, and fast flows) of water infiltrating at the cave; 2) a threshold of ~100 mm rain at the beginning of the rainy season for infiltration to begin; and 3) a decrease in lag time between rain events and infiltration response throughout the rainy season. This modeling tool and analysis approach can translate precipitation to groundwater recharge which will be very important for projecting future water resources in response to climate variability.

Simulation of Groundwater Mounding Beneath Hypothetical Stormwater Infiltration Basins

USGS Publications Warehouse

Carleton, Glen B.

2010-01-01

Groundwater mounding occurs beneath stormwater management structures designed to infiltrate stormwater runoff. Concentrating recharge in a small area can cause groundwater mounding that affects the basements of nearby homes and other structures. Methods for quantitatively predicting the height and extent of groundwater mounding beneath and near stormwater Finite-difference groundwater-flow simulations of infiltration from hypothetical stormwater infiltration structures (which are typically constructed as basins or dry wells) were done for 10-acre and 1-acre developments. Aquifer and stormwater-runoff characteristics in the model were changed to determine which factors are most likely to have the greatest effect on simulating the maximum height and maximum extent of groundwater mounding. Aquifer characteristics that were changed include soil permeability, aquifer thickness, and specific yield. Stormwater-runoff variables that were changed include magnitude of design storm, percentage of impervious area, infiltration-structure depth (maximum depth of standing water), and infiltration-basin shape. Values used for all variables are representative of typical physical conditions and stormwater management designs in New Jersey but do not include all possible values. Results are considered to be a representative, but not all-inclusive, subset of likely results. Maximum heights of simulated groundwater mounds beneath stormwater infiltration structures are the most sensitive to (show the greatest change with changes to) soil permeability. The maximum height of the groundwater mound is higher when values of soil permeability, aquifer thickness, or specific yield are decreased or when basin depth is increased or the basin shape is square (and values of other variables are held constant). Changing soil permeability, aquifer thickness, specific yield, infiltration-structure depth, or infiltration-structure shape does not change the volume of water infiltrated, it changes the shape or height of the groundwater mound resulting from the infiltration. An aquifer with a greater soil permeability or aquifer thickness has an increased ability to transmit water away from the source of infiltration than aquifers with lower soil permeability; therefore, the maximum height of the groundwater mound will be lower, and the areal extent of mounding will be larger. The maximum height of groundwater mounding is higher when values of design storm magnitude or percentage of impervious cover (from which runoff is captured) are increased (and other variables are held constant) because the total volume of water to be infiltrated is larger. The larger the volume of infiltrated water the higher the head required to move that water away from the source of recharge if the physical characteristics of the aquifer are unchanged. The areal extent of groundwater mounding increases when soil permeability, aquifer thickness, design-storm magnitude, or percentage of impervious cover are increased (and values of other variables are held constant). For 10-acre sites, the maximum heights of the simulated groundwater mound range from 0.1 to 18.5 feet (ft). The median of the maximum-height distribution from 576 simulations is 1.8 ft. The maximum areal extent (measured from the edge of the infiltration basins) of groundwater mounding of 0.25-ft ranges from 0 to 300 ft with a median of 51 ft for 576 simulations. Stormwater infiltration at a 1-acre development was simulated, incorporating the assumption that the hypothetical infiltration structure would be a pre-cast concrete dry well having side openings and an open bottom. The maximum heights of the simulated groundwater-mounds range from 0.01 to 14.0 ft. The median of the maximum-height distribution from 432 simulations is 1.0 ft. The maximum areal extent of groundwater mounding of 0.25-ft ranges from 0 to 100 ft with a median of 10 ft for 432 simulations. Simulated height and extent of groundwater mounding associ

Water quality of stormwater generated from an airport in a cold climate, function of an infiltration pond, and sampling strategy with limited resources.

PubMed

Jia, Yu; Ehlert, Ludwig; Wahlskog, Cecilia; Lundberg, Angela; Maurice, Christian

2017-12-05

Monitoring pollutants in stormwater discharge in cold climates is challenging. An environmental survey was performed by sampling the stormwater from Luleå Airport, Northern Sweden, during the period 2010-2013, when urea was used as a main component of aircraft deicing/anti-icing fluids (ADAFs). The stormwater collected from the runway was led through an oil trap to an infiltration pond to store excess water during precipitation periods and enhance infiltration and water treatment. Due to insufficient capacity, an emergency spillway was established and equipped with a flow meter and an automatic sampler. This study proposes a program for effective monitoring of pollutant discharge with a minimum number of sampling occasions when use of automatic samplers is not possible. The results showed that 90% of nitrogen discharge occurs during late autumn before the water pipes freeze and during snow melting, regardless of the precipitation during the remaining months when the pollutant discharge was negligible. The concentrations of other constituents in the discharge were generally low compared to guideline values. The best data quality was obtained using flow controlled sampling. Intensive time-controlled sampling during late autumn (few weeks) and snow melting (2 weeks) would be sufficient for necessary information. The flow meters installed at the rectangular notch appeared to be difficult to calibrate and gave contradictory results. Overall, the spillway was dry, as water infiltrated into the pond, and stagnant water close to the edge might be registered as flow. Water level monitoring revealed that the infiltration capacity gradually decreased with time.

Using artificial sweeteners to identify contamination sources and infiltration zones in a coupled river-aquifer system

NASA Astrophysics Data System (ADS)

Bichler, Andrea; Muellegger, Christian; Hofmann, Thilo

2014-05-01

In shallow or unconfined aquifers the infiltration of contaminated river water might be a major threat to groundwater quality. Thus, the identification of possible contamination sources in coupled surface- and groundwater systems is of paramount importance to ensure water quality. Micropollutants like artificial sweeteners are promising markers for domestic waste water in natural water bodies. Compounds, such as artificial sweeteners, might enter the aquatic environment via discharge of waste water treatment plants, leaky sewer systems or septic tanks and are ubiquitously found in waste water receiving waters. The hereby presented field study aims at the (1) identification of contamination sources and (2) delineation of infiltration zones in a connected river-aquifer system. River bank filtrate in the groundwater body was assessed qualitatively and quantitatively using a combined approach of hydrochemical analysis and artificial sweeteners (acesulfame ACE) as waste water markers. The investigated aquifer lies within a mesoscale alpine head water catchment and is used for drinking water production. It is hypothesized that a large proportion of the groundwater flux originates from bank filtrate of a nearby losing stream. Water sampling campaigns in March and July 2012 confirmed the occurrence of artificial sweeteners at the investigated site. The municipal waste water treatment plant was identified as point-source for ACE in the river network. In the aquifer ACE was present in more than 80% of the monitoring wells. In addition, water samples were classified according to their hydrochemical composition, identifying two predominant types of water in the aquifer: (1) groundwater influenced by bank filtrate and (2) groundwater originating from local recharge. In combination with ACE concentrations a third type of water could be discriminated: (3) groundwater influence by bank filtrate but infiltrated prior to the waste water treatment plant. Moreover, the presence of ACE at elevated concentrations in aquifer zones dominated by local recharge indicated another point-source of domestic waste water. The combined analysis of ACE and conventional hydrochemical data proved to be useful to identify different sources of waste water. It is shown that the combination of physicochemical parameters and artificial sweeteners allow for a clear delineation of infiltration areas in the investigated aquifer system.

Short-Term Summer Inundation as a Measure to Counteract Acidification in Rich Fens

PubMed Central

Mettrop, Ivan S.; Cusell, Casper; Kooijman, Annemieke M.; Lamers, Leon P. M.

2015-01-01

In regions with intensive agriculture, water level fluctuation in wetlands has generally become constricted within narrow limits. Water authorities are, however, considering the re-establishment of fluctuating water levels as a management tool in biodiverse, base-rich fens (‘rich fens’). This includes temporary inundation with surface water from ditches, which may play an important role in counteracting acidification in order to conserve and restore biodiversity. Inundation may result in an increased acid neutralizing capacity (ANC) for two reasons: infiltration of base-rich inundation water into peat soils, and microbial alkalinity generation under anaerobic conditions. The main objectives of this study were to test whether short-term (2 weeks) summer inundation is more effective than short-term winter inundation to restore the ANC in the upper 10 cm of non-floating peat soils, and to explain potential differences. Large-scale field experiments were conducted for five years in base-rich fens and Sphagnum-dominated poor fens. Winter inundation did not result in increased porewater ANC, because infiltration was inhibited in the waterlogged peat and evapotranspiration rates were relatively low. Also, low temperatures limit microbial alkalinity generation. In summer, however, when temperature and evapotranspiration rates are higher, inundation resulted in increased porewater Ca and HCO3 - concentrations, but only in areas with characteristic rich fen bryophytes. This increase was not only due to stronger infiltration into the soil, but also to higher microbial alkalinity generation under anaerobic conditions. In contrast, porewater ANC did not increase in Sphagnum-plots as a result of the ability of Sphagnum spp. to acidify their environment. In both rich and poor fens, flooding-induced P-mobilization remained sufficiently low to safeguard P-limited vegetation. NO3 - and NH4 + dynamics showed no considerable changes either. In conclusion, short-term summer inundation with base-rich and nutrient-poor surface water is considered beneficial in the management of non-floating rich fens, and much more effective than winter inundation. PMID:26637121

Evaluation of different field methods for measuring soil water infiltration

NASA Astrophysics Data System (ADS)

Pla-Sentís, Ildefonso; Fonseca, Francisco

2010-05-01

Soil infiltrability, together with rainfall characteristics, is the most important hydrological parameter for the evaluation and diagnosis of the soil water balance and soil moisture regime. Those balances and regimes are the main regulating factors of the on site water supply to plants and other soil organisms and of other important processes like runoff, surface and mass erosion, drainage, etc, affecting sedimentation, flooding, soil and water pollution, water supply for different purposes (population, agriculture, industries, hydroelectricity), etc. Therefore the direct measurement of water infiltration rates or its indirect deduction from other soil characteristics or properties has become indispensable for the evaluation and modelling of the previously mentioned processes. Indirect deductions from other soil characteristics measured under laboratory conditions in the same soils, or in other soils, through the so called "pedo-transfer" functions, have demonstrated to be of limited value in most of the cases. Direct "in situ" field evaluations have to be preferred in any case. In this contribution we present the results of past experiences in the measurement of soil water infiltration rates in many different soils and land conditions, and their use for deducing soil water balances under variable climates. There are also presented and discussed recent results obtained in comparing different methods, using double and single ring infiltrometers, rainfall simulators, and disc permeameters, of different sizes, in soils with very contrasting surface and profile characteristics and conditions, including stony soils and very sloping lands. It is concluded that there are not methods universally applicable to any soil and land condition, and that in many cases the results are significantly influenced by the way we use a particular method or instrument, and by the alterations in the soil conditions by the land management, but also due to the manipulation of the surface soil before and during the measurement. Due to the commonly found high variability, natural or induced by land management, of the soil surface and subsurface hydrological properties, and to the limitations imposed by the requirements of water for the measurements, there is proposed a simple and handy method, which do not use high volumes of water, adaptable to very different soil and land conditions, and that allow many repeated measurements with acceptable accuracy for most of the purposes. References Pla, I., 1997. A soil water balance model for monitoring soil erosion processes and effects on steep lands in the tropics. Soil Technology. 11(1):17-30. Elsevier Pla, I., 2006. Hydrological approach for assessing desertification processes in the Mediterranean region. In W.G. Kepner et al. (Editors), Desertification in the Mediterranean Region. A Security Issue. 579-600 Springer. Heidelberg (Germany) Reynolds W.D., B.T. Bowman, R.R. Brunke, C.F. Drury and C.S. Tan. 2000. Comparison of Tension Infiltrometer, Pressure Infiltrometer, and Soil Core Estimates of Saturated Hydraulic Conductivity . Soil Science Society of America Journal 64:478-484 Segal, E., S.A.Bradford, P. Shouse; N. Lazarovich, and D. Corwin. 2008. Integration of Hard and Soft Data to Characterize Field-Scale Hydraulic Properties for Flow and Transport Studies. Vadose Zone J 7:878-889 Young, E. 1991. Infiltration measurements, a review. Hydrological processes 5: 309-320.

Infiltration of pesticides in surface water into nearby drinking water supply wells

NASA Astrophysics Data System (ADS)

Malaguerra, F.; Albrechtsen, H.; Binning, P. J.

2010-12-01

Drinking water wells are often placed near streams because streams often overly permeable sediments and the water table is near the surface in valleys, and so pumping costs are reduced. The lowering of the water table by pumping wells can reverse the natural flow from the groundwater to the stream, inducing infiltration of surface water to groundwater and consequently to the drinking water well. Many attenuation processes can take place in the riparian zone, mainly due to mixing, biodegradation and sorption. However, if the water travel time from the surface water to the pumping well is too short, or if the compounds are poorly degradable, contaminants can reach the drinking water well at high concentrations, jeopardizing drinking water quality. Here we developed a reactive transport model to evaluate the risk of contamination of drinking water wells by surface water pollution. The model was validated using data of a tracer experiment in a riparian zone. Three compounds were considered: an older pesticide MCPP (Mecoprop) which is mobile and persistent, glyphosate (Roundup), a new biodegradable and strongly sorbed pesticide, and its degradation product AMPA. Global sensitivity analysis using the method of Morris was employed to identify the dominant model parameters. Results showed that the presence of an aquitard and its characteristics (degree of fracturing and thickness), pollutant properties and well depth are the crucial factors affecting the risk of drinking water well contamination from surface water. Global sensitivity analysis results were compared with rank correlation statistics between pesticide concentrations and geological parameters derived from a comprehensive database of Danish drinking water wells. Aquitard thickness and well depth are the most critical parameters in both the model and observed data.

Stable oxygen isotope analysis reveal vegetation influence on soil water movement and ecosystem water fluxes in a semi-arid oak woodland

NASA Astrophysics Data System (ADS)

Piayda, Arndt; Dubbert, Maren; Werner, Christiane; Cuntz, Matthias

2015-04-01

Mechanistically disentangling the role and function of vegetation within the hydrological cycle is one of the key questions in the interdisciplinary field of ecohydrology. The presence of vegetation can have various impacts on soil water relations: transpiration of active vegetation causes great water losses, rainfall is intercepted, soil evaporation can be reduced and infiltration, hydraulic redistribution and translatory flow might be altered. In drylands, covering around 40% of the global land surface, the carbon cycle is closely coupled to water availability due to (seasonal) droughts. Specifically savannah type ecosystems, which cover large areas worldwide, are, due to their bi-layered structure, very suitable to study the effects of distinct vegetation types on the ecosystem water cycle. Oxygen isotope signatures (δ18O) have been used to partition ecosystem evapotranspiration (ET ) because of the distinct isotopic compositions of water transpired by leaves relative to soil evaporated vapor. Recent developments in laser spectroscopy enable measurements of δ18O in the vapor phase with high temporal resolution in the field and bear a novel opportunity to trace water movement within the ecosystem. In the present study, the effects of distinct vegetation layers (i.e. trees and herbaceous vegetation) on soil water infiltration and redistribution as well as ecosystem water fluxes in a Mediterranean cork-oak woodland are disentangled. An irrigation experiment was carried out using δ18O labeled water to quantify the distinct effects of trees and herbaceous vegetation on 1) infiltration and redistribution of water in the soil profile and 2) to disentangle the effects of tree cover on the contribution of unproductive soil evaporation and understory transpiration to total ET . First results proof that stable δ18O isotopes measured onsite with laser spectroscopy is a valuable tool to trace water movement in the soil showing a much higher sensitivity than common TDR-type probes. It was possible to track soil water redistribution even beyond zero net water flux measured with TDR probes. Under shaded conditions beneath tree crowns, infiltration of precipitation reaches much deeper depths due to the limited radiation energy input and thus, reduced evaporative losses, compared to open areas between crowns. As a consequence, the isotopic enrichment back to initial conditions (as observed before the artificial precipitation event) was strongly delayed. Despite the higher water availability beneath tree crowns, transpiration of understory plants and soil evaporation rates were reduced compared to the open area due to the lack of energy. However, transpiration could be maintained much longer and at higher rates after the precipitation event then soil evaporation. These first results support previous findings at this site where a clear difference in understory plant community structure was observed. Beneath tree crowns, favorable water conditions enables a higher occurrence of grasses and nitrogen fixing forbs, whereas in between tree crowns drought adapted native species became dominant.

Thermal effect on the dynamic infiltration of water into single-walled carbon nanotubes.

PubMed

Zhao, Jianbing; Liu, Ling; Culligan, Patricia J; Chen, Xi

2009-12-01

Thermally induced variation in wetting ability in a confined nanoenvironment, indicated by the change in infiltration pressure as water molecules enter a model single-walled carbon nanotube submerged in aqueous environment, is investigated using molecular dynamics simulations. The temperature-dependent infiltration behavior is impacted in part by the thermally excited radial oscillation of the carbon nanotube, and in part by the variations of fundamental physical properties at the molecular level, including the hydrogen bonding interaction. The thermal effect is also closely coupled with the nanotube size effect and loading rate effect. Manipulation of the thermally responsive infiltration properties could facilitate the development of a next-generation thermal energy converter based on nanoporous materials.

Numerical model of water flow in a fractured basalt vadose zone: Box Canyon Site, Idaho

NASA Astrophysics Data System (ADS)

Doughty, Christine

2000-12-01

A numerical model of a fractured basalt vadose zone has been developed on the basis of the conceptual model described by Faybishenko et al. [[his issue]. The model has been used to simulate a ponded infiltration test in order to investigate infiltration through partially saturated fractured basalt. A key question addressed is how the fracture pattern geometry and fracture connectivity within a single basalt flow of the Snake River Plain basalt affect water infiltration. The two-dimensional numerical model extends from the ground surface to a perched water body 20 m below and uses an unconventional quasi-deterministic approach with explicit but highly simplified representation of major fractures and other important hydrogeologic features. The model adequately reproduces the majority of the field observation and provides insights into the infiltration process that cannot be obtained by data collection alone, demonstrating its value as a component of field studies.

A process to estimate net infiltration using a site-scale water-budget approach, Rainier Mesa, Nevada National Security Site, Nevada, 2002–05

USGS Publications Warehouse

Smith, David W.; Moreo, Michael T.; Garcia, C. Amanda; Halford, Keith J.; Fenelon, Joseph M.

2017-08-29

This report documents a process used to estimate net infiltration from precipitation, evapotranspiration (ET), and soil data acquired at two sites on Rainier Mesa. Rainier Mesa is a groundwater recharge area within the Nevada National Security Site where recharged water flows through bedrock fractures to a deep (450 meters) water table. The U.S. Geological Survey operated two ET stations on Rainier Mesa from 2002 to 2005 at sites characterized by pinyon-juniper and scrub-brush vegetative cover. Precipitation and ET data were corrected to remove measurement biases and gap-filled to develop continuous datasets. Net infiltration (percolation below the root zone) and changes in root-zone water storage were estimated using a monthly water-balance model.Site-scale water-budget results indicate that the heavily-fractured welded-tuff bedrock underlying thin (<40 centimeters) topsoil is a critical water source for vegetation during dry periods. Annual precipitation during the study period ranged from fourth lowest (182 millimeters [mm]) to second highest (708 mm) on record (record = 55 years). Annual ET exceeded precipitation during dry years, indicating that the fractured-bedrock reservoir capacity is sufficient to meet atmospheric-evaporative demands and to sustain vegetation through extended dry periods. Net infiltration (82 mm) was simulated during the wet year after the reservoir was rapidly filled to capacity. These results support previous conclusions that preferential fracture flow was induced, resulting in an episodic recharge pulse that was detected in nearby monitoring wells. The occurrence of net infiltration only during the wet year is consistent with detections of water-level rises in nearby monitoring wells that occur only following wet years.

40 CFR 440.131 - General provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... met. In no case shall a pH limitation below 5.0 be permitted. (e) Groundwater infiltration provision... infiltration contributes a substantial amount of water to the tailing impoundment or wastewater holding... groundwater infiltration. This discharge shall be subject to the limitations for mine drainage applicable to...

40 CFR 440.131 - General provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... met. In no case shall a pH limitation below 5.0 be permitted. (e) Groundwater infiltration provision... infiltration contributes a substantial amount of water to the tailing impoundment or wastewater holding... groundwater infiltration. This discharge shall be subject to the limitations for mine drainage applicable to...

Streamflow, infiltration, and ground-water recharge at Abo Arroyo, New Mexico: Chapter D in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Stewart-Deaker, Amy E.; Stonestrom, David A.; Moore, Stephanie J.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

Abo Arroyo, an ephemeral tributary to the Rio Grande, rises in the largest upland catchment on the eastern side of the Middle Rio Grande Basin (MRGB). The 30-kilometer reach of channel between the mountain front and its confluence with the Rio Grande is incised into basin-fill sediments and separated from the regional water table by an unsaturated zone that reaches 120 meters thick. The MRGB portion of the arroyo is dry except for brief flows generated by runoff from the upland catchment. Though brief, ephemeral flows provide a substantial fraction of ground-water recharge in the southeastern portion of the MRGB. Previous estimates of average annual recharge from Abo Arroyo range from 1.3 to 21 million cubic meters. The current study examined the timing, location, and amount of channel infiltration using streamflow data and environmental tracers during a four-year period (water years 1997–2000). A streamflow-gaging station (“gage”) was installed in a bedrock-controlled reach near the catchment outlet to provide high-frequency data on runoff entering the basin. Streamflow at the gage, an approximate bound on potential tributary recharge to the basin, ranged from 0.8 to 15 million cubic meters per year. Storm-generated runoff produced about 98 percent of the flow in the wettest year and 80 percent of the flow in the driest year. Nearly all flows that enter the MRGB arise from monsoonal storms in July through October. A newly developed streambed temperature method indicated the presence and duration of ephemeral flows downstream of the gage. During the monsoon season, abrupt downward shifts in streambed temperatures and suppressed diurnal ranges provided generally clear indications of flow. Streambed temperatures during winter showed that snowmelt is also effective in generating channel infiltration. Controlled infiltration experiments in dry arroyo sediments indicated that most ephemeral flow is lost to seepage before reaching the Rio Grande. Streambed temperature records confirmed this, providing evidence of only two flows reaching the Rio Grande during a three-year period (water years 1998–2000). Sub-channel chloride concentrations indicate that approximately half of the seepage loss eventually becomes ground-water recharge. Vertical profiles of pore-water chloride in transects adjacent to the channel indicate that basin-floor recharge outside the arroyo is negligible under current climatic conditions.

Are there prospects for enhanced groundwater recharge via infiltration of urban stormwater runoff?

EPA Science Inventory

This presentation will cover the basics of what a storm water best management practices and focus on infiltration-type practices using the example of rain gardens. I will demonstrate how water moves through rain gardens with a simple hydrologic model and discuss ancillary benefit...

Estimating effective soil properties of heterogeneous areas for modeling infiltration and redistribution

USDA-ARS?s Scientific Manuscript database

Field scale water infiltration and soil-water and solute transport models require spatially-averaged “effective” soil hydraulic parameters to represent the average flux and storage. The values of these effective parameters vary for different conditions, processes, and component soils in a field. For...

Gas-partitioning tracer test to qualify trapped gas during recharge

USGS Publications Warehouse

Heilweil, Victor M.; Kip, Solomon D.; Perkins, Kim S.; Ellett, Kevin M.

2004-01-01

Dissolved helium and bromide tracers were used to evaluate trapped gas during an infiltration pond experiment. Dissolved helium preferentially partitioned into trapped gas bubbles, or other pore air, because of its low solubility in water. This produced observed helium retardation factors of as much as 12 relative to bromide. Numerical simulations of helium breakthrough with both equilibrium and kinetically limited advection/dispersion/retardation did not match observed helium concentrations. However, better fits were obtained by including a decay term representing the diffusive loss of helium through interconnected, gas-filled pores. Calculations indicate that 7% to more than 26% of the porosity beneath the pond was filled with gas. Measurements of laboratory hydraulic properties indicate that a 10% decrease in saturation would reduce the hydraulic conductivity by at least one order of magnitude in the well-sorted sandstone, but less in the overlying soils. This is consistent with in situ measurements during the experiment, which show steeper hydraulic gradients in sandstone than in soil. Intrinsic permeability of the soil doubled during the first six months of the experiment, likely caused by a combination of dissolution and thermal contraction of trapped gas. Managers of artificial recharge basins may consider minimizing the amount of trapped gas by using wet, rather than dry, tilling to optimize infiltration rates, particularly in well-sorted porous media in which reintroduced trapped gas may cause substantial reductions in permeability. Trapped gas may also inhibit the amount of focused infiltration that occurs naturally during ephemeral flood events along washes and playas.

Gas-partitioning tracer test to quantify trapped gas during recharge

USGS Publications Warehouse

Heilweil, V.M.; Solomon, D.K.; Perkins, K.S.; Ellett, K.M.

2004-01-01

Dissolved helium and bromide tracers were used to evaluate trapped gas during an infiltration pond experiment. Dissolved helium preferentially partitioned into trapped gas bubbles, or other pore air, because of its low solubility in water. This produced observed helium retardation factors of as much as 12 relative to bromide. Numerical simulations of helium breakthrough with both equilibrium and kinetically limited advection/dispersion/retardation did not match observed helium concentrations. However, better fits were obtained by including a decay term representing the diffusive loss of helium through interconnected, gas-filled pores. Calculations indicate that 7% to more than 26% of the porosity beneath the pond was filled with gas. Measurements of laboratory hydraulic properties indicate that a 10% decrease in saturation would reduce the hydraulic conductivity by at least one order of magnitude in the well-sorted sandstone, but less in the overlying soils. This is consistent with in situ measurements during the experiment, which show steeper hydraulic gradients in sandstone than in soil. Intrinsic permeability of the soil doubled during the first six months of the experiment, likely caused by a combination of dissolution and thermal contraction of trapped gas. Managers of artificial recharge basins may consider minimizing the amount of trapped gas by using wet, rather than dry, tilling to optimize infiltration rates, particularly in well-sorted porous media in which reintroduced trapped gas may cause substantial reductions in permeability. Trapped gas may also inhibit the amount of focused infiltration that occurs naturally during ephemeral flood events along washes and playas.

Estimating recharge at Yucca Mountain, Nevada, USA: Comparison of methods

USGS Publications Warehouse

Flint, A.L.; Flint, L.E.; Kwicklis, E.M.; Fabryka-Martin, J. T.; Bodvarsson, G.S.

2002-01-01

Obtaining values of net infiltration, groundwater travel time, and recharge is necessary at the Yucca Mountain site, Nevada, USA, in order to evaluate the expected performance of a potential repository as a containment system for high-level radioactive waste. However, the geologic complexities of this site, its low precipitation and net infiltration, with numerous mechanisms operating simultaneously to move water through the system, provide many challenges for the estimation of the spatial distribution of recharge. A variety of methods appropriate for arid environments has been applied, including water-balance techniques, calculations using Darcy's law in the unsaturated zone, a soil-physics method applied to neutron-hole water-content data, inverse modeling of thermal profiles in boreholes extending through the thick unsaturated zone, chloride mass balance, atmospheric radionuclides, and empirical approaches. These methods indicate that near-surface infiltration rates at Yucca Mountain are highly variable in time and space, with local (point) values ranging from zero to several hundred millimeters per year. Spatially distributed net-infiltration values average 5 mm/year, with the highest values approaching 20 mm/year near Yucca Crest. Site-scale recharge estimates range from less than 1 to about 12 mm/year. These results have been incorporated into a site-scale model that has been calibrated using these data sets that reflect infiltration processes acting on highly variable temporal and spatial scales. The modeling study predicts highly non-uniform recharge at the water table, distributed significantly differently from the non-uniform infiltration pattern at the surface.

Numerical model of water flow and solute accumulation in vertisols using HYDRUS 2D/3D code

NASA Astrophysics Data System (ADS)

Weiss, Tomáš; Dahan, Ofer; Turkeltub, Tuvia

2015-04-01

Keywords: dessication-crack-induced-salinization, preferential flow, conceptual model, numerical model, vadose zone, vertisols, soil water retention function, HYDRUS 2D/3D Vertisols cover a hydrologically very significant area of semi-arid regions often through which water infiltrates to groundwater aquifers. Understanding of water flow and solute accumulation is thus very relevant to agricultural activity and water resources management. Previous works suggest a conceptual model of dessication-crack-induced-salinization where salinization of sediment in the deep section of the vadose zone (up to 4 m) is induced by subsurface evaporation due to convective air flow in the dessication cracks. It suggests that the salinization is induced by the hydraulic gradient between the dry sediment in the vicinity of cracks (low potential) and the relatively wet sediment further from the main cracks (high potential). This paper presents a modified previously suggested conceptual model and a numerical model. The model uses a simple uniform flow approach but unconventionally prescribes the boundary conditions and the hydraulic parameters of soil. The numerical model is bound to one location close to a dairy farm waste lagoon, but the application of the suggested conceptual model could be possibly extended to all semi-arid regions with vertisols. Simulations were conducted using several modeling approaches with an ultimate goal of fitting the simulation results to the controlling variables measured in the field: temporal variation in water content across thick layer of unsaturated clay sediment (>10 m), sediment salinity and salinity the water draining down the vadose zone to the water table. The development of the model was engineered in several steps; all computed as forward solutions by try-and-error approach. The model suggests very deep instant infiltration of fresh water up to 12 m, which is also supported by the field data. The paper suggests prescribing a special atmospheric boundary to the wall of the crack (so that the solute can accumulate due to evaporation on the crack block wall, and infiltrating fresh water can push the solute further down) - in order to do so, HYDRUS 2D/3D code had to be modified by its developers. Unconventionally, the main fitting parameters were: parameter a and n in the soil water retention curve and saturated hydraulic conductivity. The amount of infiltrated water (within a reasonable range), the infiltration function in the crack and the actual evaporation from the crack were also used as secondary fitting parameters. The model supports the previous findings that significant amount (~90%) of water from rain events must infiltrate through the crack. It was also noted that infiltration from the crack has to be increasing with depth and that the highest infiltration rate should be somewhere between 1-3m. This paper suggests a new way how to model vertisols in semi-arid regions. It also supports the previous findings about vertisols: especially, the utmost importance of soil cracks as preferential pathways for water and contaminants and soil cracks as deep evaporators.

Laboratory testing on infiltration in single synthetic fractures

NASA Astrophysics Data System (ADS)

Cherubini, Claudia; Pastore, Nicola; Li, Jiawei; Giasi, Concetta I.; Li, Ling

2017-04-01

An understanding of infiltration phenomena in unsaturated rock fractures is extremely important in many branches of engineering for numerous reasons. Sectors such as the oil, gas and water industries are regularly interacting with water seepage through rock fractures, yet the understanding of the mechanics and behaviour associated with this sort of flow is still incomplete. An apparatus has been set up to test infiltration in single synthetic fractures in both dry and wet conditions. To simulate the two fracture planes, concrete fractures have been moulded from 3D printed fractures with varying geometrical configurations, in order to analyse the influence of aperture and roughness on infiltration. Water flows through the single fractures by means of a hydraulic system composed by an upstream and a downstream reservoir, the latter being subdivided into five equal sections in order to measure the flow rate in each part to detect zones of preferential flow. The fractures have been set at various angles of inclination to investigate the effect of this parameter on infiltration dynamics. The results obtained identified that altering certain fracture parameters and conditions produces relevant effects on the infiltration process through the fractures. The main variables influencing the formation of preferential flow are: the inclination angle of the fracture, the saturation level of the fracture and the mismatch wavelength of the fracture.

Feedbacks Between Bioclogging and Infiltration in Losing River Systems

NASA Astrophysics Data System (ADS)

Newcomer, M. E.; Hubbard, S. S.; Fleckenstein, J. H.; Schmidt, C.; Maier, U.; Thullner, M.; Ulrich, C.; Rubin, Y.

2014-12-01

Reduction in riverbed permeability due to biomass growth is a well-recognized yet poorly understood process associated with losing connected and disconnected rivers. Although several studies have focused on riverbed bioclogging processes at the pore-scale, few studies have quantified bioclogging feedback cycles at the scale relevant for water resources management, or at the meander-scale. At this scale, often competing hydrological-biological processes influence biomass dynamics and infiltration. Disconnection begins when declines in the water table form an unsaturated zone beneath the river maximizing seepage. Simultaneously, bioclogging reduces the point-scale infiltration flux and can either limit the nutrient flux and reduce bioclogging, or preferentially focus infiltration elsewhere and enhance bioclogging. These feedbacks are highly dependent on geomorphology and seasonal patterns of discharge and water temperature. To assess the mutual influences of disconnection, biomass growth, and temperature changes on infiltration in a geomorphologically complex river system, we built a 3D numerical model, conditioned on field data, using the reactive-transport simulator MIN3P. Results show that in disconnected regions of the river, biomass growth reduced vertical seepage downward and extended the unsaturated zone length; however these changes were contingent upon disconnection. Mid-way through the seasonal cycle, biomass declined in these same regions due to limited nutrient flux. Seepage and biomass continued to oscillate with a lag correlation of 1 month. Connected regions, however, showed the largest infiltration rates, nutrient fluxes, and concentrations of biomass. Despite the reduction in conductivity from biomass, flow remains high in connected regions because the feedback between bioclogging and infiltration is not as pronounced due to the sharpening hydraulic gradient. Bioclogging ultimately shapes the pattern of flow, however geomorphology dominates the strength of connection. Recognition of the feedbacks between geomorphological patterns and heterogeneous biomass on meander scale hydrological processes can lead to better estimates of local water volumes and capacities, especially when these systems are used as municipal and public water supply sources.

Evaluating the performance of water purification in a vegetated groundwater recharge basin maintained by short-term pulsed infiltration events.

PubMed

Mindl, Birgit; Hofer, Julia; Kellermann, Claudia; Stichler, Willibald; Teichmann, Günter; Psenner, Roland; Danielopol, Dan L; Neudorfer, Wolfgang; Griebler, Christian

2015-01-01

Infiltration of surface water constitutes an important pillar in artificial groundwater recharge. However, insufficient transformation of organic carbon and nutrients, as well as clogging of sediments often cause major problems. The attenuation efficiency of dissolved organic carbon (DOC), nutrients and pathogens versus the risk of bioclogging for intermittent recharge were studied in an infiltration basin covered with different kinds of macrovegetation. The quality and concentration of organic carbon, major nutrients, as well as bacterial biomass, activity and diversity in the surface water, the porewater, and the sediment matrix were monitored over one recharge period. Additionally, the numbers of viral particles and Escherichia coli were assessed. Our study showed a fast establishment of high microbial activity. DOC and nutrients have sustainably been reduced within 1.2 m of sediment passage. Numbers of E. coli, which were high in the topmost centimetres of sediment porewater, dropped below the detection limit. Reed cover was found to be advantageous over bushes and trees, since it supported higher microbial activities along with a good infiltration and purification performance. Short-term infiltration periods of several days followed by a break of similar time were found suitable for providing high recharge rates, and good water purification without the risk of bioclogging.

Water filtration rate and infiltration/accumulation of low density lipoproteins in 3 different modes of endothelial/smooth muscle cell co-cultures.

PubMed

Ding, ZuFeng; Fan, YuBo; Deng, XiaoYan

2009-11-01

Using different endothelial/smooth muscle cell co-culture modes to simulate the intimal structure of blood vessels, the water filtration rate and the infiltration/accumulation of LDL of the cultured cell layers were studied. The three cell culture modes of the study were: (i) The endothelial cell monolayer (EC/Phi); (ii) endothelial cells directly co-cultured on the smooth muscle cell monolayer (EC-SMC); (iii) endothelial cells and smooth muscle cells cultured on different sides of a Millicell-CM membrane (EC/SMC). It was found that under the same condition, the water filtration rate was the lowest for the EC/SMC mode and the highest for the EC/Phi mode, while the infiltration/accumulation of DiI-LDLs was the lowest in the EC/Phi mode and the highest in the EC-SMC mode. It was also found that DiI-LDL infiltration/accumulation in the cultured cell layers increased with the increasing water filtration rate. The results from the in vitro model study therefore suggest that the infiltration/accumulation of the lipids within the arterial wall is positively correlated with concentration polarization of atherogenic lipids, and the integrity of the endothelium plays an important role in the penetration and accumulation of atherogenic lipids in blood vessel walls.

Catch crops impact on soil water infiltration in vineyards

NASA Astrophysics Data System (ADS)

Cerdà, Artemi; Bagarello, Vincenzo; Iovino, Massimo; Ferro, Vito; Keesstra, Saskia; Rodrigo-Comino, Jesús; García Diaz, Andrés; di Prima, Simone

2017-04-01

Infiltration is the key component of the hydrological cycle (Cerdà, 1999; Bagarello et al.,, 2014; Zema et al., 2016). Infiltration determines the partitioning of rainfall into runoff and subsurface flow (Cerdà, 1996; Bagarello et al., 2006; Wang et al., 2016). In the Mediterranean, agriculture resulted in the degradation of the soil structure, reduction of the organic matter and increase in the soil losses (Cerdà et al., 2009; Laudicina et al., 2015; Iovino et al., 2016; Willaarts et al., 2016). There is an urgent need to restore the agriculture soils to avoid floods, reduce the carbon emissions and avoid reservoir siltation (Aksakal et al., 2016; Ben Slimane et al., 2016; Yagüe et al., 2016). Catch Crops are widespread used due to their impact on the soil fertility (Mwango et al., 2016; Nishigaki et al., 2016 ; Nawaz et al., 2016). Catch crops also increase the amount of organic matter but little is known about the effect on soil infiltration. Two paired plots were selected in Les Alcusses (Moixent municipality) in Eastern Iberian Peninsula to compare the infiltration rates between a 8-years catch crop (Vicia sp) with a control (plough) soil. The measurements were carried out by means of ring infiltrometer in August 2014 and December 2014 under dry and wet conditions (Cerdà, 2001; Di Prima et al., 2016). The results show that the steady-state infiltration rates were 1.8 higher during the summer period, and that the catch crops did not increase the infiltration rates. Acknowledgements The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n 603498 (RECARE project) and the CGL2013- 47862-C2-1-R and CGL2016-75178-C2-2-R national research projects. References Aksakal, E. L., Sari, S., & Angin, I. (2016). Effects of vermicompost application on soil aggregation and certain physical properties. Land Degradation and Development, 27(4), 983-995. doi:10.1002/ldr.2350 Bagarello, V., Castellini, M., Di Prima, S., & Iovino, M. (2014). Soil hydraulic properties determined by infiltration experiments and different heights of water pouring. Geoderma, 213, 492-501. Bagarello, V., Elrick, D. E., Iovino, M., & Sgroi, A. (2006). A laboratory analysis of falling head infiltration procedures for estimating the hydraulic conductivity of soils. Geoderma, 135, 322-334. Ben Slimane, A., Raclot, D., Evrard, O., Sanaa, M., Lefevre, I., & Le Bissonnais, Y. (2016). Relative contribution of Rill/Interrill and Gully/Channel erosion to small reservoir siltation in mediterranean environments. Land Degradation and Development, 27(3), 785-797. doi:10.1002/ldr.2387 Cerdà, A. (1996). Seasonal variability of infiltration rates under contrasting slope conditions in southeast spain. Geoderma, 69(3-4), 217-232. Cerdà, A. (1999). Seasonal and spatial variations in infiltration rates in badland surfaces under mediterranean climatic conditions. Water Resources Research, 35(1), 319-328. doi:10.1029/98WR01659 Cerdà, A. (2001). Effects of rock fragment cover on soil infiltration, interrill runoff and erosion. European Journal of Soil Science, 52(1), 59-68. doi:10.1046/j.1365-2389.2001.00354.x Cerdà, A., Morera, A. G., & Bodí, M. B. (2009). Soil and water losses from new citrus orchards growing on sloped soils in the western mediterranean basin. Earth Surface Processes and Landforms, 34(13), 1822-1830. doi:10.1002/esp.1889 di Prima, S., Lassabatère, L., Bagarello, V., Iovino, M., & Angulo-Jaramillo, R. (2016). Testing a new automated single ring infiltrometer for Beerkan infiltration experiments. Geoderma, 262, 20-34. Iovino, M., Castellini, M., Bagarello, V., & Giordano, G. (2016). Using static and dynamic indicators to evaluate soil physical quality in a sicilian area. Land Degradation and Development, 27(2), 200-210. doi:10.1002/ldr.2263 Laudicina, V. A., Novara, A., Barbera, V., Egli, M., & Badalucco, L. (2015). Long-term tillage and cropping system effects on chemical and biochemical characteristics of soil organic matter in a mediterranean semiarid environment. Land Degradation and Development, 26(1), 45-53. doi:10.1002/ldr.2293 Mamedov, A. I., Bar-Yosef, B., Levkovich, I., Rosenberg, R., Silber, A., Fine, P., & Levy, G. J. (2016). Amending soil with sludge, manure, humic acid, orthophosphate and phytic acid: Effects on infiltration, runoff and sediment loss. Land Degradation and Development, 27(6), 1629-1639. doi:10.1002/ldr.2474 Mwango, S. B., Msanya, B. M., Mtakwa, P. W., Kimaro, D. N., Deckers, J., & Poesen, J. (2016). Effectiveness OF mulching under miraba in controlling soil erosion, fertility restoration and crop yield in the usambara mountains, tanzania. Land Degradation and Development, 27(4), 1266-1275. doi:10.1002/ldr.2332 Nawaz, A., Farooq, M., Lal, R., Rehman, A., Hussain, T., & Nadeem, A. (2016). Influence of sesbania brown manuring and rice residue mulch on soil health, weeds and system productivity of conservation rice-wheat systems. Land Degradation and Development, doi:10.1002/ldr.2578 Nishigaki, T., Shibata, M., Sugihara, S., Mvondo-Ze, A. D., Araki, S., & Funakawa, S. (2016). Effect of mulching with vegetative residues on soil water erosion and water balance in an oxisol cropped by cassava in east cameroon. Land Degradation and Development, doi:10.1002/ldr.2568 Wang, Y., Fan, J., Cao, L., & Liang, Y. (2016). Infiltration and runoff generation under various cropping patterns in the red soil region of china. Land Degradation and Development, 27(1), 83-91. doi:10.1002/ldr.2460 Willaarts, B. A., Oyonarte, C., Muñoz-Rojas, M., Ibáñez, J. J., & Aguilera, P. A. (2016). Environmental factors controlling soil organic carbon stocks in two contrasting mediterranean climatic areas of southern spain. Land Degradation and Development, 27(3), 603-611. doi:10.1002/ldr.2417 Yagüe, M. R., Domingo-Olivé, F., Bosch-Serra, À. D., Poch, R. M., & Boixadera, J. (2016). Dairy cattle manure effects on soil quality: Porosity, earthworms, aggregates and soil organic carbon fractions. Land Degradation and Development, 27(7), 1753-1762. doi:10.1002/ldr.2477 Zema, D. A., Labate, A., Martino, D., & Zimbone, S. M. (2016). Comparing different infiltration methods of the HEC-HMS model: The case study of the mésima torrent (southern italy). Land Degradation and Development, doi:10.1002/ldr.2591

Visualization of soil-moisture change in response to precipitation within two rain gardens in Ohio

USGS Publications Warehouse

Dumouchelle, Denise H.; Darner, Robert A.

2014-01-01

Stormwater runoff in urban areas is increasingly being managed by means of a variety of treaments that reduce or delay runoff and promote more natural infiltration. One such treatment is a rain garden, which is built to detain runoff and allow for water infiltration and uptake by plants.Water flow into or out of a rain garden can be readily monitored with a variety of tools; however, observing the movement of water within the rain garden is less straightforward. Soil-moisture probes in combination with an automated interpolation procedure were used to document the infiltration of water into two rain gardens in Ohio. Animations show changes in soil moisture in the rain gardens during two precipitation events. At both sites, the animations demonstrate underutilization of the rain gardens.

Hydrogeologic barriers to the infiltration of treated wastewater at the Joint Base McGuire-Dix-Lakehurst Land Application Site, Burlington County, New Jersey

USGS Publications Warehouse

Fiore, Alex R.

2016-09-02

For the final phase of wastewater treatment operations at Joint Base McGuire-Dix-Lakehurst in Burlington County, New Jersey, treated effluent is pumped to 12 infiltration basins on a Land Application Site to recharge the unconfined Kirkwood-Cohansey aquifer system. Two of the 12 infiltration basins are operationally ineffective because discharged effluent fails to percolate and remains ponded on the basin surfaces. A study conducted by the U.S. Geological Survey, in cooperation with the U.S. Department of Defense, investigated the potential hydrogeologic conditions preventing infiltration in these basins by testing the geophysical, lithological, and hydraulic characteristics of the aquifer material underlying the site. Saturated sand, sandy clay, and unsaturated sand were encountered in succession through the upper 4 feet of sediment below land surface at the two ineffective basins. Water levels in auger borings penetrating the clay and underlying dry sand were measured as deeper than water levels in nested auger borings in the saturated sand overlying the clay, which indicates a downward vertical gradient was established after removal of the clay in the deeper borings created a conduit for drainage from the surficial saturated sands. Ground-penetrating radar surveys and additional water levels measured in piezometer wells adjacent to the infiltration basins indicated a lack of connectivity between the ponded basin water and the regional water table, and demonstrated that perched conditions were not present in native formation materials outside the inoperable basins. Therefore, the near-surface low permeability clay is likely preventing infiltration from the basin surface and causes the ineffectiveness of the two basins for wastewater land application operations.

Case study: design, operation, maintenance and water quality management of sustainable storm water ponds for roof runoff.

PubMed

Scholz, Miklas

2004-12-01

The purpose of this case study was to optimise design, operation and maintenance guidelines, and to assess the water treatment potential of a storm water pond system after 15 months of operation. The system was based on a combined silt trap, attenuation pond and vegetated infiltration basin. This combination was used as the basis for construction of a roof water runoff system from a single domestic property. United Kingdom Building Research Establishment and Construction Industry Research and Information Association, and German Association for Water, Wastewater and Waste design guidelines were tested. These design guidelines failed because they did not consider local conditions. The infiltration function for the infiltration basin was logarithmic. Algal control techniques were successfully applied, and treatment of rainwater runoff from roofs was found to be largely unnecessary for recycling (e.g., watering plants). However, seasonal and diurnal variations of biochemical oxygen demand, dissolved oxygen and pH were recorded.

Evaluation of diffuse and preferential flow pathways of infiltrated precipitation and irrigation using oxygen and hydrogen isotopes

NASA Astrophysics Data System (ADS)

Ma, Bin; Liang, Xing; Liu, Shaohua; Jin, Menggui; Nimmo, John R.; Li, Jing

2017-05-01

Subsurface-water flow pathways in three different land-use areas (non-irrigated grassland, poplar forest, and irrigated arable land) in the central North China Plain were investigated using oxygen (18O) and hydrogen (2H) isotopes in samples of precipitation, soils, and groundwater. Soil water in the top 10 cm was significantly affected by both evaporation and infiltration. Water at 10-40 cm depth in the grassland and arable land, and 10-60 cm in poplar forest, showed a relatively short residence time, as a substantial proportion of antecedent soil water was mixed with a 92-mm storm infiltration event, whereas below those depths (down to 150 cm), depleted δ18O spikes suggested that some storm water bypassed the shallow soil layers. Significant differences, in soil-water content and δ18O values, within a small area, suggested that the proportion of immobile soil water and water flowing in subsurface pathways varies depending on local vegetation cover, soil characteristics and irrigation applications. Soil-water δ18O values revealed that preferential flow and diffuse flow coexist. Preferential flow was active within the root zone, independent of antecedent soil-water content, in both poplar forest and arable land, whereas diffuse flow was observed in grassland. The depleted δ18O spikes at 20-50 cm depth in the arable land suggested the infiltration of irrigation water during the dry season. Temporal isotopic variations in precipitation were subdued in the shallow groundwater, suggesting more complete mixing of different input waters in the unsaturated zone before reaching the shallow groundwater.

The Impact of Solar Arrays on Arid Soil Hydrology: Some Numerical Simulations

NASA Astrophysics Data System (ADS)

Luo, Y.; Berli, M.; Koonce, J.; Shillito, R.; Dijkema, J.; Ghezzehei, T. A.; Yu, Z.

2016-12-01

Hot deserts are prime locations for solar energy generation but also recognized as particularly fragile environments. Minimizing the impact of facility-scale solar installations on desert environments is therefore of increasing concern. This study focuses on the impact of photovoltaic solar arrays on the water balance of arid soil underneath the array. The goal was to explore whether concentrated rainwater infiltration along the solar panel drip lines would lead to deeper infiltration and an increase in soil water storage in the long term. A two-dimensional HYDRUS model was developed to simulate rainwater infiltration into the soil within a photovoltaic solar array. Results indicate that rainwater infiltrates deeper below the drip lines compared to the areas between solar panels but only for coarse textured soil. Finer-textured soils redistribute soil moisture horizontally and the concentrating effect of solar panels on rainwater infiltration appears to be small.

Dynamic fuzzy modeling of storm water infiltration in urban fractured aquifers

USGS Publications Warehouse

Hong, Y.-S.; Rosen, Michael R.; Reeves, R.R.

2002-01-01

In an urban fractured-rock aquifer in the Mt. Eden area of Auckland, New Zealand, disposal of storm water is via "soakholes" drilled directly into the top of the fractured basalt rock. The dynamic response of the groundwater level due to the storm water infiltration shows characteristics of a strongly time-varying system. A dynamic fuzzy modeling approach, which is based on multiple local models that are weighted using fuzzy membership functions, has been developed to identify and predict groundwater level fluctuations caused by storm water infiltration. The dynamic fuzzy model is initialized by the fuzzy clustering algorithm and optimized by the gradient-descent algorithm in order to effectively derive the multiple local models-each of which is associated with a locally valid model that represents the groundwater level state as a response to different intensities of rainfall events. The results have shown that even if the number of fuzzy local models derived is small, the fuzzy modeling approach developed provides good prediction results despite the highly time-varying nature of this urban fractured-rock aquifer system. Further, it allows interpretable representations of the dynamic behavior of the groundwater system due to storm water infiltration.

Measurement and evaluation of percolation drainage systems capacity in real conditions

NASA Astrophysics Data System (ADS)

Markovic, G.; Zelenakova, M.

2017-10-01

The drainage system must ensure a safe disposal of the surface water without endangering the buildings and safety of people. Despite the common use of rainwater infiltration facilities, there is still only limited data available evaluating the long-term capacity of such systems especially for underground infiltration facilities. This study presents experimental measurements and evaluation of long-term infiltration efficiency in real conditions and emphasizes the importance of hydrogeological survey. The measurements of infiltration efficiency were applied to an existing percolation drainage system - infiltration shafts. Infiltration shafts were made in year 2007 so that its drainage operation takes more than 8 years. This study was started in 2011 and still continues and presents 5 years measurements of infiltration efficiency for this infiltration facility.

Analysis of Instrumentation to Monitor the Hydrologic Performance of Green Infrastructure at the Edison Environmental Center

EPA Science Inventory

Infiltration is one of the primary functional mechanisms of green infrastructure stormwater controls, so this study explored selection and placement of embedded soil moisture and water level sensors to monitor surface infiltration and infiltration into the underlying soil for per...

Monitoring infiltration and recharge of playa lakes in the Texas Southern High Plains

USDA-ARS?s Scientific Manuscript database

Preliminary results from playa lakes monitored by the Texas Water Development Board (TWDB) suggest that a small volume of deep infiltration and recharge to the Ogallala aquifer occurs along the margins of the lake beds, while the majority of infiltration associated with a typical inundation remains ...

40 CFR 133.103 - Special considerations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... total flow to the POTW (i.e., wastewater plus inflow plus infiltration) is less than 275 gallons per... influent wastewater does not result from either excessive infiltration or clear water industrial discharges... excessive infiltration is discussed in 40 CFR 35.2005(b)(28), plus the additional criterion that either 40...

40 CFR 133.103 - Special considerations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... total flow to the POTW (i.e., wastewater plus inflow plus infiltration) is less than 275 gallons per... influent wastewater does not result from either excessive infiltration or clear water industrial discharges... excessive infiltration is discussed in 40 CFR 35.2005(b)(28), plus the additional criterion that either 40...

Applicability of five models to simulate water infiltration into soil with added biochar

USDA-ARS?s Scientific Manuscript database

As a soil amendment, biochar can reduce soil bulk density, increase soil porosity, and alter soil aggregates and thus affect the infiltration. Researchers have proposed and revised several theoretical models to describe the process of soil infiltration. Although these models have been successfully u...

40 CFR 133.103 - Special considerations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... total flow to the POTW (i.e., wastewater plus inflow plus infiltration) is less than 275 gallons per... influent wastewater does not result from either excessive infiltration or clear water industrial discharges... excessive infiltration is discussed in 40 CFR 35.2005(b)(28), plus the additional criterion that either 40...

40 CFR 133.103 - Special considerations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... total flow to the POTW (i.e., wastewater plus inflow plus infiltration) is less than 275 gallons per... influent wastewater does not result from either excessive infiltration or clear water industrial discharges... excessive infiltration is discussed in 40 CFR 35.2005(b)(28), plus the additional criterion that either 40...

40 CFR 133.103 - Special considerations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... total flow to the POTW (i.e., wastewater plus inflow plus infiltration) is less than 275 gallons per... influent wastewater does not result from either excessive infiltration or clear water industrial discharges... excessive infiltration is discussed in 40 CFR 35.2005(b)(28), plus the additional criterion that either 40...

Engineering report single-shell tank farms interim measures to limit infiltration through the vadose zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

HAASS, C.C.

1999-10-14

Identifies, evaluates and recommends interim measures for reducing or eliminating water sources and preferential pathways within the vadose zone of the single-shell tank farms. Features studied: surface water infiltration and leaking water lines that provide recharge moisture, and wells that could provide pathways for contaminant migration. An extensive data base, maps, recommended mitigations, and rough order of magnitude costs are included.

On-site infiltration of road runoff using pervious pavements with subjacent infiltration trenches as source control strategy.

PubMed

Fach, S; Dierkes, C

2011-01-01

The focus in this work was on subsoil infiltration of stormwater from parking lots. With regard to operation, reduced infiltration performance due to clogging and pollutants in seepage, which may contribute to contaminate groundwater, are of interest. The experimental investigation covered a pervious pavement with a subjacent infiltration trench draining an impervious area of 2 ha. In order to consider seasonal effects on the infiltration performance, the hydraulic conductivity was measured tri-monthly during monitoring with a mobile sprinkling unit. To assess natural deposits jointing, road bed, gravel of infiltration trenches and subsoil were analysed prior to commencement of monitoring for heavy metals, polycyclic aromatic and mineral oil type hydrocarbons. Furthermore, from 22 storm events, water samples of rainfall, surface runoff, seepage and ground water were analysed with regard to the above mentioned pollutants. The study showed that the material used for the joints had a major impact on the initial as well as the final infiltration rates. Due to its poor hydraulic conductivity, limestone gravel should not be used as jointing. Furthermore, it is recommended that materials for the infiltration facilities are ensured free of any contaminants prior to construction. Polycyclic aromatic and mineral oil type hydrocarbons were, with the exception of surface runoff, below detection limits. Heavy metal concentrations of groundwater were with the exception of lead (because of high background concentrations), below the permissible limits.

Fate of human viruses in groundwater recharge systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaughn, J.M.; Landry, E.F.

1980-03-01

The overall objective of this research program was to determine the ability of a well-managed tertiary effluent-recharge system to return virologically acceptable water to the groundwater aquifer. The study assessed the quality of waters renovated by indigenous recharge operations and investigated a number of virus-soil interrelationships. The elucidation of the interactions led to the establishment of basin operating criteria for optimizing virus removal. Raw influents, chlorinated tertiary effluents, and renovated wastewater from the aquifer directly beneath a uniquely designed recharge test basin were assayed on a weekly basis for the presence of human enteroviruses and coliform bacteria. High concentrations ofmore » viruses were routinely isolated from influents but were isolated only on four occasions from tertiary-treated sewage effluents. In spite of the high quality effluent being recharged, viruses were isolated from the groundwater observation well, indicating their ability to penetrate the unsaturated zone. Results of poliovirus seeding experiments carried out in the test basin clearly indicated the need to operate recharge basins at low (e.g. 1 cm/h) infiltration rates in areas having soil types similar to those found at the study site. The method selected for reducing the test basin infiltration rate involved clogging the basin surface with settled organic material from highly turbid effluent. Alternative methods for slowing infiltration rates are discussed in the text.« less

Soil water infiltration impacted by maize (zea mays) growth on sloping agricultural land of the loess plateau

USDA-ARS?s Scientific Manuscript database

Increasing infiltration rates of sloping agricultural land from arid and semiarid regions not only affects water supply and precipitation transformations in soil directly, but also impacts erosion intensity. This is extremely important to the Loess Plateau regions of Northwest China, where a majorit...

Effect of topsoil thickness on soil water infiltration in corn-soybean rotation and switchgrass production systems

USDA-ARS?s Scientific Manuscript database

Switchgrass and corn are sometimes used as a resource for biofuel production. The effect of production management systems on water infiltration is very critical in claypan landscape to increase production as well as minimize economic and environmental risks. The objective of this study was to evalua...

Soil water infiltration affected by topsoil thickness in row crop and switchgrass production systems

USDA-ARS?s Scientific Manuscript database

Conversion of annual grain crop systems to biofuel production systems can restore soil hydrologic function; however, information on these effects is limited. Hence, the objective of this study was to evaluate the influence of topsoil thickness on water infiltration in claypan soils for grain and swi...

Negative trade-off between changes in vegetation water use and infiltration recovery after reforesting degraded pasture land in the Nepalese Lesser Himalaya

NASA Astrophysics Data System (ADS)

Ghimire, C. P.; Bruijnzeel, L. A.; Lubczynski, M. W.; Bonell, M.

2014-03-01

This work investigates the trade-off between increases in vegetation water use and rain water infiltration afforded by soil improvement after reforesting severely degraded grassland in the Lesser Himalaya of Central Nepal. The hillslope hydrological functioning (surface- and sub-soil hydraulic conductivities and overland flow generation) and the evapotranspiration (rainfall interception and transpiration) of the following contrasting vegetation types were quantified and examined in detail: (i) a nearly undisturbed natural broad-leaved forest; (ii) a mature, intensively-used pine plantation; and (iii) a highly degraded pasture. Planting pines increased vegetation water use relative to the pasture and natural forest situation by 355 and 55 mm year-1, respectively. On balance, the limited amount of extra infiltration afforded by the pine plantation relative to the pasture (only 90 mm year-1 due to continued soil degradation associated with regular harvesting of litter and understory vegetation in the plantation) proved insufficient to compensate the higher water use of the pines. As such, observed declines in dry season flows in the study area are thought to reflect the higher water use of the pines although the effect could be moderated by better forest and soil management promoting infiltration. In contrast, a comparison of the water use of the natural forest and degraded pasture suggests that replacing the latter by (mature) broad-leaved forest would (ultimately) have a near-neutral effect on dry season flows as the approximate gains in infiltration and evaporative losses were very similar (ca. 300 m year-1 each). The results of the present study underscore the need for proper forest management for optimum hydrological functioning as well as the importance of protecting the remaining natural forests in the region.

Negative trade-off between changes in vegetation water use and infiltration recovery after reforesting degraded pasture land in the Nepalese Lesser Himalaya

NASA Astrophysics Data System (ADS)

Ghimire, C. P.; Bruijnzeel, L. A.; Lubczynski, M. W.; Bonell, M.

2014-12-01

This work investigates the trade-off between increases in vegetation water use and rain water infiltration afforded by soil improvement after reforesting severely degraded grassland in the Lesser Himalaya of central Nepal. The hillslope hydrological functioning (surface and subsurface soil hydraulic conductivities and overland flow generation) and the evapotranspiration (rainfall interception and transpiration) of the following contrasting vegetation types were quantified and examined in detail: (i) a nearly undisturbed, natural broadleaved forest; (ii) a 25-year-old, intensively-used pine plantation; and (iii) a highly degraded pasture. Planting pines increased vegetation water use relative to the pasture and natural forest situation by 355 and 55 mm year-1, respectively. On balance, the limited amount of extra infiltration afforded by the pine plantation relative to the pasture (only 90 mm year-1 due to continued soil degradation associated with regular harvesting of litter and understory vegetation in the plantation) proved insufficient to compensate the higher water use of the pines. As such, observed declines in dry season flows in the study area are thought to mainly reflect the higher water use of the pines although the effect could be moderated by better forest and soil management promoting infiltration. In contrast, a comparison of the water use of the natural forest and degraded pasture suggests that replacing the latter by (mature) broadleaved forest would (ultimately) have a near-neutral effect on dry season flows as the approximate gains in infiltration and evaporative losses were very similar (ca. 300 mm year-1 each). The results of the present study underscore the need for proper forest management for optimum hydrological functioning as well as the importance of protecting the remaining natural forests in the region.

PACE-90 water and solute transport calculations for 0.01, 0.1, and 0. 5 mm/yr infiltration into Yucca Mountain; Yucca Mountain Site Characterization Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dykhuizen, R.C.; Eaton, R.R.; Hopkins, P.L.

1991-12-01

Numerical results are presented for the Performance Assessment Calculational Exercise (PACE-90). One- and two-dimensional water and solute transport are presented for steady infiltration into Yucca Mountain. Evenly distributed infiltration rates of 0.01, 0.1, and 0.5 mm/yr were considered. The calculations of solute transport show that significant amounts of radionuclides can reach the water table over 100,000 yr at the 0.5 mm/yr rate. For time periods less than 10,000 yr or infiltrations less than 0.1 mm/yr very little solute reaches the water table. The numerical simulations clearly demonstrate that multi-dimensional effects can result in significant decreases in the travel time ofmore » solute through the modeled domain. Dual continuum effects are shown to be negligible for the low steady state fluxes considered. However, material heterogeneities may cause local amplification of the flux level in multi-dimensional flows. These higher flux levels may then require modeling of a dual continuum porous medium.« less

Providing the physical basis of SCS curve number method and its proportionality relationship from Richards' equation

NASA Astrophysics Data System (ADS)

Hooshyar, M.; Wang, D.

2016-12-01

The empirical proportionality relationship, which indicates that the ratio of cumulative surface runoff and infiltration to their corresponding potentials are equal, is the basis of the extensively used Soil Conservation Service Curve Number (SCS-CN) method. The objective of this paper is to provide the physical basis of the SCS-CN method and its proportionality hypothesis from the infiltration excess runoff generation perspective. To achieve this purpose, an analytical solution of Richards' equation is derived for ponded infiltration in shallow water table environment under the following boundary conditions: 1) the soil is saturated at the land surface; and 2) there is a no-flux boundary which moves downward. The solution is established based on the assumptions of negligible gravitational effect, constant soil water diffusivity, and hydrostatic soil moisture profile between the no-flux boundary and water table. Based on the derived analytical solution, the proportionality hypothesis is a reasonable approximation for rainfall partitioning at the early stage of ponded infiltration in areas with a shallow water table for coarse textured soils.

An analytical solution of Richards' equation providing the physical basis of SCS curve number method and its proportionality relationship

NASA Astrophysics Data System (ADS)

Hooshyar, Milad; Wang, Dingbao

2016-08-01

The empirical proportionality relationship, which indicates that the ratio of cumulative surface runoff and infiltration to their corresponding potentials are equal, is the basis of the extensively used Soil Conservation Service Curve Number (SCS-CN) method. The objective of this paper is to provide the physical basis of the SCS-CN method and its proportionality hypothesis from the infiltration excess runoff generation perspective. To achieve this purpose, an analytical solution of Richards' equation is derived for ponded infiltration in shallow water table environment under the following boundary conditions: (1) the soil is saturated at the land surface; and (2) there is a no-flux boundary which moves downward. The solution is established based on the assumptions of negligible gravitational effect, constant soil water diffusivity, and hydrostatic soil moisture profile between the no-flux boundary and water table. Based on the derived analytical solution, the proportionality hypothesis is a reasonable approximation for rainfall partitioning at the early stage of ponded infiltration in areas with a shallow water table for coarse textured soils.

Experimental quantification of solute transport through the vadose zone under dynamic boundary conditions with dye tracers and optical methods.

NASA Astrophysics Data System (ADS)

Cremer, Clemens; Neuweiler, Insa

2017-04-01

Knowledge of subsurface solute transport processes is vital to investigate e.g. groundwater contamination, nutrient uptake by plant roots and to implement remediation strategies. Beside field measurements and numerical simulations, physical laboratory experiments represent a way to establish process understanding and furthermore validate numerical schemes. Atmospheric forcings, such as erratically varying infiltration and evaporation cycles, subject the shallow subsurface to local and temporal variations in water content and associated hydraulic conductivity of the prevailing porous media. Those variations in material properties can cause flow paths to differ between upward and downward flow periods. Thereby, the unsaturated subsurface presents a highly complicated, dynamic system. Following an extensive systematical numerical investigation of flow and transport through bimodal, unsaturated porous media under dynamic boundary conditions (Cremer et al., 2016), we conduct physical laboratory experiments in a 22 cm x 8 cm x 1 cm flow cell where we introduce structural heterogeneity in the form sharp material interfaces between different porous media. In all experiments, a constant pressure head is implemented at the lower boundary, while cyclic infiltration-evaporation phases are applied at the soil surface. As a reference case a stationary infiltration with a rate corresponding to the cycle-averaged infiltration rate is applied. By initial application of dye tracers, solute transport within the domain is visualized such that transport paths and redistribution processes can be observed in a qualitative manner. Solute leaching is quantified at the bottom outlet, where breakthrough curves are obtained via spectroscopy. Liquid and vapor flow in and out of the domain is obtained from multiple balances. Thereby, the interplay of material structural heterogeneity and alternating flow (transport) directions and flow (transport) paths is investigated. Results show lateral transport through the material interface which differs between the stationary (unilateral) and dynamic cases (bilateral). This qualitative observation is confirmed by breakthrough curves for dynamic experiments which generally show the trend of faster initial breakthrough and increased tailing when compared to stationary infiltration results. Literature Cremer, C.J.M., I. Neuweiler, M. Bechtold, J. Vanderborght (2016): Solute Transport in Heterogeneous Soil with Time-Dependent Boundary Conditions, Vadose Zone Journal 15 (6) DOI: 10.2136/vzj2015.11.0144

Numerical demonstration of surfactant concentration-dependent capillarity and viscosity effects on infiltration from a constant flux line source

NASA Astrophysics Data System (ADS)

Henry, Eric J.; Smith, James E.

2006-09-01

SummarySurface infiltration line sources can deliver surfactant solutions for agricultural purposes or for use in subsurface remediation. Though the prediction of water distribution below a line source has received considerable attention in the scientific literature, little has been has been reported on how infiltration of surfactant solution from a line source differs from water infiltration. Few numerical models are capable of simulating surfactant-induced changes in moisture characteristic and hydraulic conductivity properties of unsaturated soil, so it is difficult to assess the importance of these effects when designing surfactant application schemes. We investigated surfactant infiltration behavior by using the variably-saturated flow and transport model HYDRUS-2D [Simunek, J., Sejna, M., van Genuchten, M.Th., 1999. The HYDRUS-2D software package for simulating the two-dimensional movement of water, heat, and multiple solutes in variably-saturated media, Version 2.0. IGWMC-TPS-53C. International Ground Water Modeling Center, Colorado School of Mines, Golden, CO] which was modified by [Henry, E.J., Smith, J.E., Warrick, A.W., 2002. Two-dimensional modeling of flow and transport in the vadose zone with surfactant-induced flow. Water Resour. Res. 38. DOI: doi:10.1029/2001WR000674] to incorporate surfactant effects on unsaturated flow. Significant differences were found between pure water and surfactant solution infiltration into a fine sand that was initially at residual moisture content. The surfactant solution wetted a larger area, both horizontally and vertically, relative to water, while the distribution of water within the wetted zone was more uniform than in the surfactant system. The surfactant system exhibited transient localized drainage and rewetting caused by surfactant-induced capillary pressure gradients within the wetting front. A standard unsaturated flow model (i.e., one that does not include surfactant effects on flow) is not capable of capturing the transient flow behavior. However, our results show that by using an effective scaled media (ESM) approach a standard model can be used to simulate later-time hydraulic conditions in a surfactant system.

Fate of Arsenic during Red River Water Infiltration into Aquifers beneath Hanoi, Vietnam

PubMed Central

2016-01-01

Recharge of Red River water into arsenic-contaminated aquifers below Hanoi was investigated. The groundwater age at 40 m depth in the aquifer underlying the river was 1.3 ± 0.8 years, determined by tritium–helium dating. This corresponds to a vertical flow rate into the aquifer of 19 m/year. Electrical conductivity and partial pressure of CO2 (PCO2) indicate that water recharged from the river is present in both the sandy Holocene and gravelly Pleistocene aquifers and is also abstracted by the pumping station. Infiltrating river water becomes anoxic in the uppermost aquifer due to the oxidation of dissolved organic carbon. Further downward, sedimentary carbon oxidation causes the reduction of As-containing Fe-oxides. Because the release of arsenic by reduction of Fe-oxides is controlled by the reaction rate, arsenic entering the solution becomes highly diluted in the high water flux and contributes little to the groundwater arsenic concentration. Instead, the As concentration in the groundwater of up to 1 μM is due to equilibrium-controlled desorption of arsenic, adsorbed to the sediment before river water started to infiltrate due to municipal pumping. Calculations indicate that it will take several decades of river water infiltration to leach arsenic from the Holocene aquifer to below the World Health Organization limit of 10 μg/L. PMID:27958705

Fate of Arsenic during Red River Water Infiltration into Aquifers beneath Hanoi, Vietnam.

PubMed

Postma, Dieke; Mai, Nguyen Thi Hoa; Lan, Vi Mai; Trang, Pham Thi Kim; Sø, Helle Ugilt; Nhan, Pham Quy; Larsen, Flemming; Viet, Pham Hung; Jakobsen, Rasmus

2017-01-17

Recharge of Red River water into arsenic-contaminated aquifers below Hanoi was investigated. The groundwater age at 40 m depth in the aquifer underlying the river was 1.3 ± 0.8 years, determined by tritium-helium dating. This corresponds to a vertical flow rate into the aquifer of 19 m/year. Electrical conductivity and partial pressure of CO 2 (P CO 2 ) indicate that water recharged from the river is present in both the sandy Holocene and gravelly Pleistocene aquifers and is also abstracted by the pumping station. Infiltrating river water becomes anoxic in the uppermost aquifer due to the oxidation of dissolved organic carbon. Further downward, sedimentary carbon oxidation causes the reduction of As-containing Fe-oxides. Because the release of arsenic by reduction of Fe-oxides is controlled by the reaction rate, arsenic entering the solution becomes highly diluted in the high water flux and contributes little to the groundwater arsenic concentration. Instead, the As concentration in the groundwater of up to 1 μM is due to equilibrium-controlled desorption of arsenic, adsorbed to the sediment before river water started to infiltrate due to municipal pumping. Calculations indicate that it will take several decades of river water infiltration to leach arsenic from the Holocene aquifer to below the World Health Organization limit of 10 μg/L.

Quantitative framework for preferential flow initiation and partitioning

USGS Publications Warehouse

Nimmo, John R.

2016-01-01

A model for preferential flow in macropores is based on the short-range spatial distribution of soil matrix infiltrability. It uses elementary areas at two different scales. One is the traditional representative elementary area (REA), which includes a sufficient heterogeneity to typify larger areas, as for measuring field-scale infiltrability. The other, called an elementary matrix area (EMA), is smaller, but large enough to represent the local infiltrability of soil matrix material, between macropores. When water is applied to the land surface, each EMA absorbs water up to the rate of its matrix infiltrability. Excess water flows into a macropore, becoming preferential flow. The land surface then can be represented by a mesoscale (EMA-scale) distribution of matrix infiltrabilities. Total preferential flow at a given depth is the sum of contributions from all EMAs. Applying the model, one case study with multi-year field measurements of both preferential and diffuse fluxes at a specific depth was used to obtain parameter values by inverse calculation. The results quantify the preferential–diffuse partition of flow from individual storms that differed in rainfall amount, intensity, antecedent soil water, and other factors. Another case study provided measured values of matrix infiltrability to estimate parameter values for comparison and illustrative predictions. These examples give a self-consistent picture from the combination of parameter values, directions of sensitivities, and magnitudes of differences caused by different variables. One major practical use of this model is to calculate the dependence of preferential flow on climate-related factors, such as varying soil wetness and rainfall intensity.

Air Permeability and Infiltration Differences Associated with Grass and Gravel Streambeds in an Urban Environment

NASA Astrophysics Data System (ADS)

Witte, B.; Ferlin, C.; Gallo, E. L.; Lohse, K. A.; Meixner, T.; Brooks, P. D.; Ferre, T. A.

2010-12-01

Storm water infiltration and recharge is a key component of sustainable water resource management in rapidly expanding urban areas of arid and semi-arid regions. Near surface streambed permeability affects the partitioning of stream flows to infiltration and subsequent groundwater recharge, or increasing runoff to be conveyed downstream. Therefore, in this study, we assessed how air permeability varied among distinct stream beds of ephemeral urban washes in the semi-arid southwest. A Soil Core Air Permeameter (SCAP) was used to quantify in situ air permeability at sixteen sites in the Tucson, Arizona metropolitan area. Significant air permeability differences between gravel and grass lined ephemeral stream beds were found, where the average air permeability at the gravel sites was 3.58 x10-2 ± 1.11 x 10-2 mm2 (mean ± std error) and the air permeability at the grass sites was 7.13 x 10-3 ± 2.02 x 10-3 mm2. A previously published linear correlation between air permeability and saturated hydraulic conductivity was used to predict saturated hydraulic conductivity at the ephemeral stream beds of this study. Preliminary results suggest that the predicted saturated hydraulic conductivity values are comparable to ring infiltration measurements taken in the field. Findings from this study indicate that the higher porosity and decreased vegetation at the gravel lined urban washes enhanced infiltration rates, which may lead to decreased storm water runoff. However, higher infiltration rates at gravel lined sites may result in less time for processing of potential pollutants with negative implications for water quality.

An Experimental Investigation of Infiltration in a Shallow Karst System

NASA Astrophysics Data System (ADS)

Bellin, A.; Becker, M. W.; Borsato, A.

2008-12-01

We present preliminary results of a field investigation of infiltration in a karst terrain in the Dolomiti del Brenta ridge, North-East Italy. A sub-horizontal cave 40 m deep drains a small catchment of about 6,000 m2 at the elevation of 2,600 m a.s.l. in a fractured triassic dolomite formation. The surface is characterized by a thin soil cover, vertical fractures, and karst collapse features (dolines). Water infiltrates through the dolines and vertical shafts which are connected to an unsaturated cave system. Within the cave, water discharge, temperature, and electric conductivity are recorded. Meterological conditions were measured at a weather station installed within the cave contributing area. Furthermore, in order to study residence time distribution in the summer 2007 we conducted a tracer experiment by injecting fluorescein in one of the dolines and recording its concentration within the cave. The recorded time series are statistically non-stationary with a wavelet spectrum strongly variable in time. However, a closer inspection of the water discharge wavelet spectrum reveals three periods in which the local power spectrum is nearly time invariant: November-April, April -July and August-October. In the first period we observe a slow exponential decline of the water discharge. The season is dominated by release of water from subsurface storage, in absence of surface input. In the second period, the system is dominated by snowmelt with a time lag that reduces from 9 hours to 1 hour through the melting season. The variation in time apparently corresponds with reduction in snowpack thickness. In the final period, the system is dominated by rainfall. The lag time in this period is on the order of 1 hour or less. These results suggest that in this hydrologic system the distribution of the residence time, and thus the transfer function relating input to output signals, is not state invariant, as typically assumed in applications. Rather, hydraulic residence time is seasonally variable and linked to both surface and subsurface hydrologic conditions.

Simulated ground-water flow and sources of water in the Killbuck Creek Valley near Wooster, Wayne County, Ohio

USGS Publications Warehouse

Breen, K.J.; Kontis, A.L.; Rowe, G.L.; Haefner, R.J.

1995-01-01

The stratified-drift aquifer in the 3,000-ft (feet)-wide and 100-ft-deep buried valley of Killbuck Creek near Wooster in northeastern Ohio was studied. The stratified drift with adjacent sandstone and shale bedrock produce a system of ground-water flow representative of the western part of the glaciated north-eastern United States. The stratified-drift aquifer is an excellent source of water for municipal and industrial wells. The aquifer is recharged locally by water from precipitation on the valley floor and uplands, by infiltration from streams, and by lateral flow to the valley from the uplands. As a result, the aquifer is vulnerable to surface or subsurface spills of contaminants in the valley or the adjacent uplands. Quality of water in the stratified drift is affected by influx of water from bedrock lateral to or beneath the valley. This influx is controlled, in part, by the pumping stress placed on the stratified-drift aquifer. Hydrogeologic and aqueous-geochemical data were analyzed to establish the framework necessary for stead-state and transient simulations of ground-water flow in stratified drift and bedrock with a three-layer ground-water-flow model. A new model routine, the Variable-Recharge procedure, was developed to simulate areal recharge and the contribution of the uplands to the drift system. This procedure allows for water applied to land surface to infiltrate or to be rejected. Rejected recharge and ground water discharged when the water table is at land surface form surface runoff-this excess upland water can be redirected as runoff to other parts of the model. Infiltration of streamwater, areal recharge to uplands and valley, and lateral subsurface flow from the uplands to the valley are sources of water to the stratufued0druft aquifer. Water is removed from the stratified-drift aquifer at Wooster primarily by production wells pumping at a rate of approximately 8.5 ft3/s (cubic feet per second). The ground-water budget resulting from two types of simulations of ground-water flow in this study indicates the primary sources of water to the wells are recharge at or near land surface and lateral subsurface flow from the shale and sandstone bedrock. Components of recharge at land surface include induced infiltration from streams, precipitation on the valley floor, and infiltration of unchanneled upland runoff that reaches the valley floor. The steady-state simulation was designed to represent conditions during the fall of 1984. The transient simulation was designed to represent an 11-day snowmelt event, 23 February to 5 March 1985, that caused water levels to rise significantly throughout the valley. Areal recharge to the valley and flow from the uplands to the valley were determined through the Variable-Recharge procedure. The total steady-state recharge to the valley was 12.5 ft3/s. Upland sources, areal valley recharge, and induced infiltration from Killnuck Creek accounted for 63, 23, and 8 percent, respectively, of the valley recharge. An analysis of the simulated vertical flow to the buried stratified drift through surficial slit, clay, and fine sand indicates that about 75 percent of the total recharge to the buried deposits is the sum of areally extensive, relatively small flows less than about 0.01 ft? /s per model node), whereas about 25 percent of the recharge results from a really restricted, relatively large flows (greater than about 0.01 ft? /s per model node). The large-magnitude flows are located primarily beneath Clear and Little Killbuck Creeks where seepage provides abundant recharge and the surficial sediments grade into coarser alluvial-fan deposits. Chemical and isotopic studies of ground water and streamwater combined with measurements of stream infiltration provide independent support for the conclusions derived from computer simulation of ground-water flow. In addition, the chemical and isotopic studies helped quantity the rate and pathways of infiltrating water from

Use of a three-dimensional model for the analysis of the ground-water flow system in Parker Valley, Arizona and California

USGS Publications Warehouse

Tucci, Patrick

1982-01-01

A three-dimensional, finite-difference model was used to simulate ground-water flow conditions in Parker Valley. The study evaluated present knowledge and concepts of the ground-water system and the ability of the model to represent the system. Modeling assumptions and generalized physical parameters that were used may have transfer value in the construction and calibration of models of other basins along the lower Colorado River. The aquifer was simulated in two layers to represent the three-dimensional system. Ground-water conditions were simulated for 1940-41, the mid-1960's, and 1980. Overall model results generally compared favorably with available field information. The model results showed that for 1940-41 the Colorado River was a losing stream through out Parker Valley. Infiltration of surface water from the river was the major source of recharge. The dominant mechanism of discharge was evapotranspiration by phreatophytes. Agricultural development between 1941 and the mid-1960 's resulted in significant changes to the ground-water system. Model results for conditions in the mid-1960 's showed that the Colorado River had become a gaining stream in the northern part of the valley as a result of higher water levels. The rise in water levels was caused by infiltration of applied irrigation water. Diminished water-level gradients from the river in the rest of the valley reduced the amount of infiltration of surface water from the river. Models results for conditions in 1980 showed that ground-water level rises of several feet caused further reduction in the amount of surface-water infiltration from the river. (USGS)

Generalization and formalization of the US EPA procedure for design of treated wastewater aquifer recharge basins: II. Retrofit of Souhil Wadi (Nabeul, Tunisia) pilot plant.

PubMed

Kallali, Hamadi; Yoshida, Mitsuo; Tarhouni, Jamila; Jedidi, Naceur

2013-01-01

The 'Cap Bon' peninsula in Tunisia suffers from intensive tourist activities, high demographic increase and industrial development. As groundwater had been for a long time the main water source, aquifers had been subject to a severe depletion and seawater intrusion. Despite the measures taken prohibiting new drillings and water carrying by the construction of a waterway linking the region to the north-west region of Tunisia, the problem of water shortage persists. Artificial recharge of groundwater with treated wastewater has been decided as a technique to replenish the region aquifers. A pilot plant was constructed in the early 1980s in Souhil Wadi (Nabeul) area. Many experiments have been carried out on this plant and have led to controversial opinions about its performance and its impact on groundwater contamination. This contribution concerns the application of the procedure that we developed from the generalization and the formalization of the United States Environmental Protection Agency (US EPA) methodology for the design of treated wastewater aquifer recharge basins. This upgrading procedure implemented in a spreadsheet, has been used to retrofit the Souhil Wadi facility in order to improve its performance. This method highlighted the importance of the safety factor to estimate wastewater infiltration rate from clean water permeability measurements. It has, also, demonstrated the discordance between the initial design parameters of Souhil Wadi facility and their current status as they have changed with time and the infiltration capacity of the basins has been affected by clogging. Indeed, it has been demonstrated that with the current state of clogging of the basins, the design infiltration rate limited by the most restrictive layer (6.1 cm/hr) corresponds to 22% of the surface infiltration rate reached after a drying period of 10 d, which means that we need more basins to absorb the daily loading rate. The design method leads to the construct ion of five basins of 961 m(2) (31 × 31 m) each, with one basin being flooded for 3 d with 27 cm of water daily and rested for 10 d. The current status is completely different as only four basins are constructed with 324 m(2) each. Many actions in the short, medium and long term have been advised in order to improve the system performance.

Topic III - Infiltration and Drainage: A section in Joint US Geological Survey, US Nuclear Regulatory Commission workshop on research related to low-level radioactive waste disposal, May 4-6, 1993, National Center, Reston, Virginia; Proceedings (WRI 95-4015)

USGS Publications Warehouse

Prudic, David E.; Gee, Glendon; Stevens, Peter R.; Nicholson, Thomas J.

1996-01-01

Infiltration into and drainage from facilities for the disposal of low-level radioactive wastes is considered the major process by which non-volatile contaminants are transported away from the facilities. The session included 10 papers related to the processes of infiltration and drainage, and to the simulation of flow and transport through the unsaturated zone. The first paper, presented by David Stonestrom, was an overview regarding the application of unsaturated flow theory to infiltration and drainage. Stonestrom posed three basic questions, which are:How well do we know the relevant processes affecting flow and transport?How well can we measure the parametric functions used to quantify flow and transport?How do we treat complexities inherent in field settings?The other nine papers presented during the session gave some insight to these questions. Topics included: laboratory measurement of unsaturated hydraulic conductivities at low water contents, by John Nimmo; use of environmental tracers to identify preferential flow through fractured media and to quantify drainage, by Edmund Prych and Edwin Weeks; field experiments to evaluate relevant processes affecting infiltration and drainage, by Brian Andraski, Glendon Gee, and Peter Wierenga; and the use of determinist'c and stochastic models for simulating flow and transport through heterogeneous sediments, by Richard Hills, Lynn Gelhar, and Shlomo Neuman.

Movement of water infiltrated from a recharge basin to wells

USGS Publications Warehouse

O'Leary, David R.; Izbicki, John A.; Moran, Jean E.; Meeth, Tanya; Nakagawa, Brandon; Metzger, Loren; Bonds, Chris; Singleton, Michael J.

2012-01-01

Local surface water and stormflow were infiltrated intermittently from a 40-ha basin between September 2003 and September 2007 to determine the feasibility of recharging alluvial aquifers pumped for public supply, near Stockton, California. Infiltration of water produced a pressure response that propagated through unconsolidated alluvial-fan deposits to 125 m below land surface (bls) in 5 d and through deeper, more consolidated alluvial deposits to 194 m bls in 25 d, resulting in increased water levels in nearby monitoring wells. The top of the saturated zone near the basin fluctuates seasonally from depths of about 15 to 20 m. Since the start of recharge, water infiltrated from the basin has reached depths as great as 165 m bls. On the basis of sulfur hexafluoride tracer test data, basin water moved downward through the saturated alluvial deposits until reaching more permeable zones about 110 m bls. Once reaching these permeable zones, water moved rapidly to nearby pumping wells at rates as high as 13 m/d. Flow to wells through highly permeable material was confirmed on the basis of flowmeter logging, and simulated numerically using a two-dimensional radial groundwater flow model. Arsenic concentrations increased slightly as a result of recharge from 2 to 6 μg/L immediately below the basin. Although few water-quality issues were identified during sample collection, high groundwater velocities and short travel times to nearby wells may have implications for groundwater management at this and at other sites in heterogeneous alluvial aquifers.

Measurement of infiltration rates in urban sewer systems by use of oxygen isotopes.

PubMed

De Bénédittis, J; Bertrand-Krajewski, J L

2005-01-01

The paper presents the principle of a method to measure infiltration rates in sewer systems based on the use of oxygen isotopes and its application in Lyon (France). In the urban area of Lyon, significant differences in delta 18O that can reach 3 per thousand are observed between the oxygen isotopic compositions of groundwater originating from Rhone, Saone and from their associated alluvial aquifers. Drinking water supplying Lyon results mainly from pumping in the Rhone alluvial aquifer. Therefore, in some areas, the difference of isotopic composition between wastewater resulting from the consumption of drinking water and local groundwater can be used to measure infiltration in sewer systems. The application in the catchment of Ecully shows that the infiltration flow rate presents strong fluctuations at an hourly scale: it varies between 15 and 40 m3/h. This variability could be explained by non-constant discharges of pumping and by variations of the water level in the sewer.

MORPHOLOGICAL CHANGES IN MICE LIVER IN DYNAMICS OF CONCANAVALIN A - INDUCED HEPATITIS.

PubMed

Pavlovych, S I; Makogon, N V; Grushka, N G; Bryzgina, T M; Janchiy, R I

The injure of the liver tissue and its infiltration by cells of the innate and adaptive immunity in dynamics of Con A-induced hepatitis in mice was studied. The semiquantitative method of damage rate of microcirculation channel and liver parenchyma was used, leukocyte liver infiltration and cellular composition of infiltrates were investigated also. Primary liver reaction to the Con-A was the inflammatory changes in the vascular bed, followed by disturbances in the parenchyma.The sufficient increasing of leukocyte migration to the liver was revealed. Besides, the neutrophile infiltration was increased first with a maximum at 6 hours of the experiment (63,9 ±4,6%, p<0,001 to the control level) ,and then the lymphocyte infiltration was increased with creation of manycellular lymphocytemacrophage infiltrates (62% at 48 hours comparing to 6 hours of experiment) and sufficient quantity of plasma cells population (4,9%, p<0,05 comparing to 6 hours of experiment). The obtained data gives the base to suggest that the elevated infiltration of liver tissue by leukocytes, particularly by lymphocytes and monocytes, together with necrotic death increasing creats the conditions for effective intracellular interaction and immune response to autoantigenes. This can be the essential pathogenic mechanism of development of autoimmune liver deseases.

Monitoring Soil Infiltration In Semi-Arid Regions With Meteosat And A Coupled Model Approach Using PROMET And SLC

NASA Astrophysics Data System (ADS)

Klug, P.; Bach, H.; Migdall, S.

2013-12-01

In arid regions the infiltration of sparse rainfalls and resulting ground water recharge is a critical quantity for the water cycle. With the PROMET model the infiltration process can be simulated in detail, since 4 soil layers together with the hourly calculation time step allow simulating the vertical water transport. Wet soils are darker than dry soils. Using the SLC reflectance model this effect can be simulated and compared to temporal high resolution time series of measured reflectances from Meteosat in order to monitor the drying process. This study demonstrates how MSG can be used to better parameterize the simulation of the infiltration process and reduce uncertainties in ground water recharge estimation. The study is carried out in the frame of the EU FP7 project CLIMB (Climate Induced Changes on the Hydrology of Mediterranean Basins). According to climate projections, Mediterranean countries are at risk of changes in the hydrological budget, the agricultural productivity and drinking water supply in the future. The CLIMB FP-7 project coordinated by the University of Munich (LMU) aims at employing integrated hydrological modelling in a new framework to reduce existing uncertainties in climate change impact analysis of the Mediterranean region [1, 2].

Estimation of biotransformation and sorption of emerging organic compounds (EOCs) during artificial recharge through a reactive barrier.

NASA Astrophysics Data System (ADS)

Valhondo, C.; Martinez-Landa, L.; Carrera, J.; Hidalgo, J. J.; Ayora, C.

2016-12-01

The reuse of lesser quality water such as effluents from wastewater treatment plants or effluent-receiving water bodies has been promoted due to the water shortages affecting many regions of the world. Artificial recharge through infiltration basins is known to improve several water quality parameters including the attenuation of emerging organic compounds (EOCs). Many of these contaminants exhibit redox dependent biotransformation because the redox state is one of the factors controlling microbial community development. Together with biotransformation, sorption also affects the behavior of EOCs in their passage through the soil. We studied EOCs attenuation in an infiltration system is located in Sant Vicenç dells Horts on the Llobregat delta (Barcelona, Spain), where the local water agency has an artificial recharge pilot project . The Llobregat river water used for the artificial recharge is affected by treatment plant effluents which contain EOCs. A reactive barrier consisting of vegetable compost, clay, and iron oxide was installed in the bottom of the infiltration basin to enhance biotransformation and sorption of EOCs. The barrier releases dissolved organic carbon, which favors the development of a broad range of redox environments, and supplies neutral, cationic, and anionic surfaces to favor sorption of different types of contaminants. Results were excellent, but quantitative evaluation of the EOCs attenuation requires knowledge of the residence time distribution of infiltrated water. A tracer test was performed by adding tracers to the infiltration water and interpreting the breakthrough curves at diverse monitoring points with a 2D multilayer numerical model. The calibrated model quantify degradation, as a first order law, and sorption through a linear distribution coefficient for ten selected EOCs. Results indicate higher degradation rates and sorption coefficients in the reactive barrier than in the rest of the aquifer for nine and eight of the ten studied EOCs, respectively, which demonstrates the efficiency of the reactive barrier to enhance the removal of EOCs.

Spatial variability of induced ground-water recharge beneath the Russian River, California

NASA Astrophysics Data System (ADS)

Rosenberry, D. O.; Hatch, C. E.; Cox, M. H.; Zamora, C.; Cloud, A.; Constantz, J. E.; Seymour, D.

2004-12-01

The Sonoma County Water Agency extracts water from the alluvial aquifer adjacent to and beneath the Russian River via large-volume Ranney-type collector wells. To aid in this extraction, the stage of the river is increased approximately 3 meters by an inflatable dam. In addition, raising the dam allows water to be diverted into infiltration basins that are located adjacent to the river. Removal of aquifer water induces large fluxes from surface water to ground water through the beds of the infiltration basins and the river. Total extraction during maximum summer withdrawals via five collector wells indicates an average flux from surface water to ground water through the riverbed and infiltration basins of 153 cm/d. Measurements of flux using in-river and in-pond piezometers, diurnal sediment-temperature data, and seepage meters, indicate that actual seepage fluxes are spatially variable and large seepage fluxes are concentrated in specific locations, some of which may not be intuitive. For example, we expected greatest induced seepage fluxes to occur above laterals that extend beneath the river and deliver water to a collector well. Seepage flux along a transverse transect of the riverbed that was located above laterals from one of the collector wells averaged 10 cm/d. At the same time, seepage flux along a transect that was 500 m upstream, and farther from the influence of the collector-well system, averaged 40 cm/d. Seepage fluxes from the central portion of one of the recharge basins averaged 3 cm/d whereas seepage fluxes near the margin of that infiltration basin averaged 250 cm/d. Seepage fluxes derived from in-stream-piezometer Darcy calculations were surprisingly consistent with seepage fluxes derived from seepage-meter measurements. Seepage fluxes derived from temperature measurements were slightly less comparable to the piezometer and seepage-meter measurements. The 121 cm/d average of all seepage-flux measurements was similar to the spatially-integrated rate (153 cm/d) based on the volume of water extracted from the river by the pumping wells divided by the affected area of the riverbed and the flooded infiltration ponds.

Hydrogeophysics and geochemistry reveal heterogeneity and water quality improvements in aquifer recharge and recovery (ARR) (Invited)

NASA Astrophysics Data System (ADS)

Parsekian, A.; Regnery, J.; Wing, A.; Knight, R. J.; Drewes, J. E.

2013-12-01

Aquifer recharge and recover (ARR) is the process of infiltrating water into the ground for storage and withdrawal through wells at a later time. Two significant challenges faced during the design of ARR systems are 1) evaluating aquifer heterogeneity and 2) understanding the rock fluid interactions; these knowledge gaps may have profound impacts on the volume of recoverable water and the improvement in water quality in comparison with the source-water. Our objective in this research is to leverage the advantages of hydrogeophysical measurements and geochemical sampling to reveal the properties of an aquifer through which ARR water travels with the goal of informing current operations and future design decisions. Combined geophysical and geochemical investigations reveal subsurface heterogeneity, indicate possible flow paths though the aquifer and quantify specific reductions in contaminant concentrations. Ground penetrating radar (GPR), electromagnetic induction (EMI) and electrical resistivity tomography (ERT) were used to image the subsurface throughout two key infiltration/extraction areas of an ARR site in Colorado, USA. The most valuable results came from 2.5D ERT revealing the structural patterns and suggesting the distribution of textural composition of unconsolidated sediments. Geochemical measurements on transects intersecting the geophysical measurements resolved bulk parameters (i.e. total organic carbon, cations, anions) and trace organic contaminants (e.g. trace organic compounds) and were also used to estimate mixing and water travel times and assess the performance of the ARR site regarding water quality and quantity. Our results indicate that the subsurface is highly heterogeneous at our study site and that the coarse-grained sedimentary units, acting as the best conduit for transporting water, are likely discontinuous. The electrical resistivity measurements indicate certain areas of the infiltration basins may have good hydraulic connections to the extraction wells, while other infiltration basins may be separated by fine-grained materials from their respective extraction wells. The geochemical results imply consistent improvements in water quality that can be achieved within short travel times (<5 days) at this ARR site receiving riverbank filtered water for infiltration.

Water Repellent Soils: The use of electrical resistivity tomography in a small scale catchment model to evaluate the effectiveness of surfactants.

NASA Astrophysics Data System (ADS)

Lowe, Mary-Anne; Mathes, Falko; McGrath, Gavan; Leopold, Matthias

2017-04-01

Soil water repellence effects large areas of land in Western Australia causing large forfeits in agricultural profit. Surfactants are a potential management tool, however, in field trials they have had varied success and their impact on water movement is poorly understood. This study employs a novel approach to determine the effectiveness of surfactants at modifying infiltration into water repellent soils. Using a physical catchment model (0.6 m × 0.6 m) with soils arranged in a ridge and furrow topography, irrigation and runoff were quantified. Electrical resistivity tomography (ERT) was used to measure changes in soil moisture patterns in two dimensions. Two sandy soils with contrasting severity of water repellence, as measured by the Molarity of Ethanol Droplet (MED) test, were assessed. The impact of two surfactants, at an equivalent rate of 1 L ha-1, and an untreated control were monitored over 5 wetting events. With surfactant application the very severely water repellent soil (MED 4.2 M) showed an increase in infiltration of up to 31%, which was concentrated under the area of surfactant application in the furrow. Volumetric water contents beneath the furrow increased up to 40% below 20 mm depth. Water infiltration into the untreated soil with low water repellence (MED 1.0 M) was 98%, and this did not significantly change with surfactant application. This physical catchment model, combined with hydrological and geophysical monitoring provides a useful tool to assess the effectiveness of surfactants in increasing water infiltration and subsurface soil moisture in water repellent soils. The work is part of the Australian CRC for Polymer project.

Hydrogeochemical processes of wastewater leakage purification from a thermal power plant.

PubMed

Pavlov, Sergey Kh; Chudnenko, Konstantin V

2015-01-01

The hydrogeochemical conditions of a large flatland-type ash dump (Eastern Siberia, Russia) were studied. High-alkalinity sulphate water with high calcium content was found to infiltrate into the aquifer from the ash dump. The water was transformed into neutral bicarbonate solutions. Simulation of physicochemical interactions of the clarified water with ash, sandstone, and soil demonstrated that the composition of the resulting simulated solutions is similar to composition of the transformed clarified water leaking into the aquifer, and moving at various distances from their place of infiltration towards the discharge area.

River infiltration to a subtropical alluvial aquifer inferred using multiple environmental tracers

NASA Astrophysics Data System (ADS)

Lamontagne, S.; Taylor, A. R.; Batlle-Aguilar, J.; Suckow, A.; Cook, P. G.; Smith, S. D.; Morgenstern, U.; Stewart, M. K.

2015-06-01

Chloride (Cl-), stable isotope ratios of water (δ18O and δ2H), sulfur hexafluoride (SF6), tritium (3H), carbon-14 (14C), noble gases (4He, Ne, and Ar), and hydrometry were used to characterize groundwater-surface water interactions, in particular infiltration rates, for the Lower Namoi River (New South Wales, Australia). The study period (four sampling campaigns between November 2009 and November 2011) represented the end of a decade-long drought followed by several high-flow events. The hydrometry showed that the river was generally losing to the alluvium, except when storm-derived floodwaves in the river channel generated bank recharge—discharge cycles. Using 3H/14C-derived estimates of groundwater mean residence time along the transect, infiltration rates ranged from 0.6 to 5 m yr-1. However, when using the peak transition age (a more realistic estimate of travel time in highly dispersive environments), the range in infiltration rate was larger (4-270 m yr-1). Both river water (highest δ2H, δ18O, SF6, 3H, and 14C) and an older groundwater source (lowest δ2H, δ18O, SF6, 3H, 14C, and highest 4He) were found in the riparian zone. This old groundwater end-member may represent leakage from an underlying confined aquifer (Great Artesian Basin). Environmental tracers may be used to estimate infiltration rates in this riparian environment but the presence of multiple sources of water and a high dispersion induced by frequent variations in the water table complicates their interpretation.

Analysis of Instrumentation Selection and Placement to Monitor the Hydrologic Performance of Permeable Pavement Systems and Bioinfiltration Areas at the Edison Environmental Center in New Jersey - proceedings paper

EPA Science Inventory

Infiltration is one of the primary functional mechanisms of green infrastructure stormwater controls, so this study explored selection and placement of embedded soil moisture, water level, and temperature sensors to monitor surface infiltration and infiltration into the underlyin...

Chemical quality of base flow in 18 selected streams in the upper Susquehanna River basin, New York

USGS Publications Warehouse

Hetcher, Kari K.; Miller, Todd S.; Komor, Steven C.

2004-01-01

Ground water from four production wells in the villages of Afton, Sidney, Unadilla, and Otego was analyzed for chlorofluorocarbons (CFCs) to indicate the approximate age of the water in these wells and the potential for induced infiltration of river water. The water at two of these wells is probably between 26 and 50 years old; the ages of water at the other two wells could not be reliably estimated because of CFC contamination from a nonatmospheric source. The two wells for which CFC analysis gave reliable results (Afton and Otego) probably do not induce infiltration of river water into the aquifer.

Efficiencies of multilayer infiltration systems for the removal of urban runoff pollutants.

PubMed

Hou, Lizhu; Liu, Fang; Feng, Chuanping; Wan, Li

2013-01-01

Current rates of urban development will result in water runoff becoming a major complication of urban water pollution. To address the worsening situation regarding water resource shortage and pollution, novel multilayer infiltration systems were designed and their effectiveness for removing pollutants in urban runoff tested experimentally. The multilayer infiltration systems effectively removed most pollutants, including organic matter (chemical oxygen demand (CODCr)), total nitrogen (TN), ammonia-nitrogen (NH4(+)-N) and total phosphorus (TP). CODCr, TN, NH4(+)-N, and TP were reduced by 68.67, 23.98, 82.66 and 92.11%, respectively. The main mechanism for nitrogen removal was biological nitrogen removal through nitrification and denitrification. Phosphorus in the urban runoff was removed mainly by fixation processes in the soil, such as adsorption and chemical precipitation. The results indicate that the proposed novel system has potential for removal of pollutants from urban runoff and subsequent reuse of the treated water.

Streamflow, infiltration, and recharge in Arroyo Hondo, New Mexico: Chapter F in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Moore, Stephanie J.; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

Infiltration events in channels that flow only sporadically produce focused recharge to the Tesuque aquifer in the Española Basin. The current study examined the quantity and timing of streamflow and associated infiltration in Arroyo Hondo, an unregulated mountain-front stream that enters the basin from the western slope of the Sangre de Cristo Mountains. Traditional methods of stream gaging were combined with environmental-tracer based methods to provide the estimates. The study was conducted during a three-year period, October 1999–October 2002. The period was characterized by generally low precipitation and runoff. Summer monsoonal rains produced four brief periods of streamflow in water year 2000, only three of which extended beyond the mountain front, and negligible runoff in subsequent years. The largest peak flow during summer monsoon events was 0.59 cubic meters per second. Snowmelt was the main contributor to annual streamflow. Snowmelt produced more cumulative flow downstream from the mountain front during the study period than summer monsoonal rains.The presence or absence of streamflow downstream of the mountain front was determined by interpretation of streambed thermographs. Infiltration rates were estimated by numerical modeling of transient vertical streambed temperature profiles. Snowmelt extended throughout the instrumented reach during the spring of 2001. Flow was recorded at a station two kilometers downstream from the mountain front for six consecutive days in March. Inverse modeling of this event indicated an average infiltration rate of 1.4 meters per day at this location. For the entire study reach, the estimated total annual volume of infiltration ranged from 17,100 to 246,000 m3 during water years 2000 and 2001. During water year 2002, due to severe drought, streamflow and streambed infiltration in the study reach were both zero.

Water vapor mass balance method for determining air infiltration rates in houses

Treesearch

David R. DeWalle; Gordon M. Heisler

1980-01-01

A water vapor mass balance technique that includes the use of common humidity-control equipment can be used to determine average air infiltration rates in buildings. Only measurements of the humidity inside and outside the home, the mass of vapor exchanged by a humidifier/dehumidifier, and the volume of interior air space are needed. This method gives results that...

The impact of sewage-contaminated river water on groundwater ammonium and arsenic concentrations at a riverbank filtration site in central Delhi, India

NASA Astrophysics Data System (ADS)

Groeschke, Maike; Frommen, Theresa; Taute, Thomas; Schneider, Michael

2017-11-01

The groundwater abstracted at a well field near the Yamuna River in Central Delhi, India, has elevated ammonium (NH4 +) concentrations up to 35 mg/L and arsenic (As) concentrations up to 0.146 mg/L, constituting a problem with the provision of safe drinking and irrigation water. Infiltrating sewage-contaminated river water is the primary source of the NH4 + contamination in the aquifer, leading to reducing conditions which probably trigger the release of geogenic As. These conclusions are based on the evaluation of six 8-27-m deep drillings, and 13 surface-water and 69 groundwater samples collected during seven field campaigns (2012-2013). Results indicate that losing stream conditions prevail and the river water infiltrates into the shallow floodplain aquifer (up to 16 m thickness), which consists of a 1-2-m thick layer of calcareous nodules (locally known as kankar) overlain by medium sand. Because of its higher hydraulic conductivity (3.7 × 10-3 m/s, as opposed to 3.5 × 10-4 m/s in the sand), the kankar layer serves as the main pathway for the infiltrating water. However, the NH4 + plume front advances more rapidly in the sand layer because of its significantly lower cation exchange capacity. Elevated As concentrations were only observed within the NH4 + plume indicating a causal connection with the infiltrating reducing river water.

Constraints on the Hydrologic Settings and Recharge of the Freshwater Lenses in Kuwait

NASA Astrophysics Data System (ADS)

Milewski, A.; Sultan, M.; Al-Dousari, A.

2010-12-01

The majority of the World’s arid and semi-arid countries receive rare, yet extreme, precipitation events. Recharge is minimal due to high evaporation and low infiltration rates. We show that Kuwait experiences geologic and hydrologic settings that are quite different, conditions that promote groundwater recharge. Kuwait is generally flat (slope: 2m/km) and is largely covered (80% of Kuwait’s land) by alluvial deposits with high infiltration capacities; these conditions inhibit runoff and promote infiltration and recharge of aquifers. On the average Kuwait receives 200 mm/yr over a few, but intensive events. Groundwater flows from the SW to the NE and the salinity increases along the flow gradient reaching salinities of 150,000 TDS in the NE. The presence of saline and hypersaline groundwater on local and/or regional scales in arid and hyperarid environments is usually considered as unwelcome news to hydrogeologists. That is not the case everywhere in Kuwait. In the southern regions, infiltrating fresh water mixes with the saline groundwater (TDS: 5,000 to 10,000) in the unconfined aquifers rendering it unsuitable for drinking and irrigation purposes, whereas in the northern regions, infiltrating water form lenses of fresh water on top of the highly saline (TDS >35,000) unconfined aquifers. Using the Raudhatain Watershed (3,696 km^2) in northern Kuwait as our test site, and knowing the locations of fresh water lenses in the watershed, we identified settings which facilitate the formation of these lenses and used these criteria to identify additional potential occurrences. Identified criteria include the presence of gentle slopes, permeable surface material, infrequent yet intensive (>20mm/hr) precipitation events, drainage depressions to collect the limited runoff, and presence of regional unconfined saline aquifers. Approximately 20 locations (size: 3 km2 to 150 km^2) were identified. Over the investigated period (1998- 2006), 25 precipitation events were reported, five of which exceeded 20 mm/hr; no flows were reported at the watershed outlet and no long-term ponding was detected on Landsat TM images acquired shortly after (1 to 14 days) each of the precipitation events suggesting that infiltration is quite high. This suggestion is supported by: (1) examination of NDVI images (from Landsat TM) and soil moisture images (from AMSR-E) which show that the observed increases in soil moisture content and vegetation index following a large precipitation events are not restricted to the valley network, and (2) the highly porous nature of the mapped soils (e.g., gravel, sand) and the high infiltration rates (up to 9m/day) reported for these soils. Using the SWAT continuous rainfall runoff model and taking advantage of global remote sensing datasets and GIS technologies, we estimate: (1) the average annual precipitation, runoff, and recharge at: 837 x 106m3, 6.9 x 10^6m^3, and 636 x 10^6m^3, respectively, and (2) recharge in the identified depressions at 41.6 x 10^6m^3. Results demonstrate the enhanced opportunities for groundwater recharge in the examined watershed and highlight the potential for similar applications in arid areas elsewhere.

Application of minidisk infiltrometer to estimate soil water repellency

NASA Astrophysics Data System (ADS)

Alagna, Vincenzo; Iovino, Massimo; Bagarello, Vincenzo; Mataix-Solera, Jorge; Lichner, Ľubomír

2016-04-01

Soil water repellency (SWR) reduces affinity of soils to water resulting in detrimental implication for plants growth as well as for hydrological processes. During the last decades, it has become clear that SWR is much more widespread than formerly thought, having been reported for a wide variety of soils, land uses and climatic conditions. The repellency index (RI), based on soil-water to soil-ethanol sorptivity ratio, was proposed to characterize subcritical SWR that is the situation where a low degree of repellency impedes infiltration but does not prevent it. The minidisk infiltrometer allows adequate field assessment of RI inherently scaled to account for soil physical properties other than hydrophobicity (e.g., the volume, connectivity and the geometry of pores) that directly influence the hydrological processes. There are however some issues that still need consideration. For example, use of a fixed time for both water and ethanol sorptivity estimation may lead to inaccurate RI values given that water infiltration could be negligible whereas ethanol sorptivity could be overestimated due to influence of gravity and lateral diffusion that rapidly come into play when the infiltration process is very fast. Moreover, water and ethanol sorptivity values need to be determined at different infiltration sites thus implying that a large number of replicated runs should be carried out to obtain a reliable estimate of RI for a given area. Minidisk infiltrometer tests, conducted under different initial soil moisture and management conditions in the experimental sites of Ciavolo, Trapani (Italy) and Javea, Alicante (East Spain), were used to investigate the best applicative procedure to estimate RI. In particular, different techniques to estimate the water, Sw, and ethanol, Se, sorptivities were compared including i) a fixed 1-min time interval, ii) the slope of early-time 1D infiltration equation and iii) the two-term transient 3D infiltration equation that explicitly accounts for the effects of gravity and lateral expansion. According to Pekárová et al. (2015), the combination of all the ethanol and water sorptivities was used to calculate an aggregated repellency index, RIa, that accounts for the influence of spatial variability. Alternatively, the plot of the water cumulative infiltration vs. square root of time, exhibiting a clear "hockey-stick-like" shape, was used to estimate a single-test repellency index, RI∗, that overcomes the limitations of the traditional approach given that information on both the hydrophobic and the wettable states of soil are gathered from a unique infiltration test. The mean RI values were affected by the technique used to estimate Sw and Se. In particular, the choice of a fixed time interval lead to overestimation of RI up to a factor of 3.2 as compared with the other techniques. The RIa yielded unbiased estimations of the mean RI values and also allowed to quantify the variability of SWR within a given area. A statistically significant relationship was found between RI∗ and RI but also between RI∗ and the water retention cessation time, that is the time hydrophobic turns into wettable soil, thus indicating that RI∗ is potentially able detect both the degree and the persistence of SWR. Pekárová P., Pekár J., Lichner Ľ. 2015. A new method for estimating soil water repellency index. Biologia, 70(11):1450-1455.

The hydrological response to precipitations of a layered shallow sloping deposit: physical experiments and mathematical modeling

NASA Astrophysics Data System (ADS)

Damiano, Emilia; Greco, Roberto; Guida, Andrea; Olivares, Lucio; Picarelli, Luciano

2016-04-01

Although rainfall-induced landslides are frequent, so that they can be probably considered the most widespread natural hazards, fortunately the occurrence of an extreme rainfall event only rarely corresponds to the triggering of landslides. This is due to the fact that slopes, although often considered as separated systems in the stability analyses, are actually part of a larger, more complex hydrological system, with which continuously exchange water. Indeed, most of the slopes do not fail, and when they are subjected to heavy precipitation, effective draining mechanisms spontaneously develop, such as overland and subsurface runoff, and sometimes even new preferential flow paths originated by mechanical processes, such as piping erosion or deformation cracks. Hence, the triggering of a rainfall-induced landslide requires these dynamically evolving (non-linear) drainage processes to be incapable of releasing the excess of water (and pressure) accumulating within the slope. For the case of shallow sloping covers, the capability of the slope to effectively drain the infiltrating water depends on the hydraulic properties of the involved soils (hydraulic conductivity and water retention curves) and on the hydraulic boundary conditions (at the base of the cover, where it lays upon the bedrock, and at the foot of the slope), which are in turn strongly influenced by the initial moisture state (often indicated as a predisposing cause), owing to the non-linearity of the hydraulic processes. Such an already complex picture is furthermore complicated by heterogeneity. In this study, we focus our attention onto the effects of a layered soil cover with contrasting hydraulic properties on the infiltration and drainage processes in a shallow pyroclastic deposit. This is a typical situation along many pyroclastic-covered slopes of Campania (southern Italy), which present alternations of ashes (silty sands) and pumices (sands with gravel) deposited by volcanic eruptions, and where shallow landslides are sometimes triggered by intense and long-lasting precipitations. Several studies have already pointed out that layering may play a crucial role in the development of the infiltration process, as the coarse-grained pumice layers may behave as capillary barriers, leading to the formation of perched saturated zones. The hydrological behavior of such kind of layered slopes is investigated by means of small-scale infiltration experiments carried out in an instrumented flume in the laboratory. The interpretation of the experimental results is made with the help of a mathematical model of 2-D Richards equation, which allows shedding some light in the hydraulic properties of the pumices, which are hardly measurable with standard laboratory techniques. The obtained results show how, depending on initial moisture conditions, slope inclination angle and applied rainfall intensity, the response of the slope may be very different, and that the formation of a capillary barrier is not always observed.

The role of topography and surface cover upon soil formation along hillslopes in arid climates

NASA Astrophysics Data System (ADS)

Yair, Aaron

1990-09-01

Two north-facing soil toposequences were selected from within the northern Negev desert, Israel, where average annual rainfall ranges from 70 to 200 mm. Both slopes are composed of an upper rocky and a lower colluvial section. Similar trends were found along both slopes. A high salt content was characteristic of soils at the top of the slope; salinity decreased downslope within the rocky slope section. The opposite occurred along the colluvial slopes, with salinity increasing sharply downslope. At any location along the slopes the northernmost soil toposequence site (160 mm average annual rainfall) represents, from a pedological point of view, an environment which is far more arid than its climatologically drier, more southern counterpart. The explanation provided for the variation of soil proporties at the scale of single hillslopes and at the regional scale is the same. It is contended that water input into the soil, and therefore leaching intensity, is positively related to the ratio of bedrock/soil cover. Rocky areas have limited infiltration, thus yielding high runoff rates into adjoining soil-covered areas, and contribute to water concentration, deeper infiltration and leaching intensity. Soil or sediment-covered areas having relatively high absorption capacities will experience reduced runoff, shallow infiltration and decreased water availability for leaching. This leads over time to salt accumulation at a shallow depth. The decrease in rock/soil ratio downslope within the colluvium is therefore held responsible for the corresponding increase in salinity. Similarly, the greater salinity of the soils in the northern site is explained by the fact that its rock/soil ratio is lower than in the southern area. The theoretical and practical implications regarding the relationship between climatic change and landscape evolution in arid areas are briefly discussed.

Chemical spring water measurements coupled with 2d u.d.e.c hydromechanical modelling as an investigation methodology of water infiltration influence on large moving rock mass stability : application to the "la clapière" landslide (france, 06).

NASA Astrophysics Data System (ADS)

Cappa, F.; Guglielmi, Y.; Soukatchoff, V. M.; Mudry, J.; Bertrand, C.; Charmoille, A.

2003-04-01

We present an investigation method of water infiltration influence on Large Moving Rock Mass (LMRM) stability. In the case of huge unstable mountainous slopes, it has been clearly shown that the main driving of instability is gravity and that the major triggering and increasing factor is water located in interstices and fractures of rocks (Noverraz &al., 1998). More particularly, groundwater originates from a localized hydro-mechanical deformation inside fractures that can induce a generalized destabilization of large rock masses (Guglielmi, 1999). However, the understanding of groundwater mechanical effects on landslides and their neighbouring environment is rendered more complex given the large anisotropy of the rock mass as well as the difficulties to apply classic hydrogeological investigation methods in a moving environment. For these reasons, we developped an indirect investigation method based on chemical groundwater measurements coupled with a two-dimensional hydro-mechanical modelling with the Universal Distinct Element Code (UDEC) numerical program, taking the example of the La Clapière landslide (Alpes-Maritimes, France). The methodology we develop firstly establishes a hydro-mechanical conceptual scheme through the analysis of geological, hydrogeological, hydrogeochemistry and landslide velocity measurements. Then, a two-dimensional numerical modelling with UDEC was performed to test the influence of the locations and the intensities of water infiltrations on the hydro-mechanical behaviour of La Clapière’s slope. A geological and hydrogeological analysis reveals a perched saturated zone connected by large conducting-flow fractures to a basal aquifer. The correlations of spring water chemistry data and meteorological events on the slope highlight a large variability of groundwater transits in the slope in time (transit durations of 1 to 21 days) and in space. Infiltration transients correlate with landslide accelerations. Infiltration yields range between 0.4 and 0.8 l.s-1. The most intensive hydro-mechanical response of the landslide is linked to snowmelt in a stable area in the upper part of the slope located between 1800 and a 2500 m high. On the one hand modeling hydro-mechanical effects with UDEC considers a model corresponding to a slope without any unstable zone, and on the other hand, a model including a failure surface in order to simulate the current instability. In the two numerical tests, calculations show that the most unstabilizing water infiltration corresponds to water infiltrations located in the middle part of the slope for weak flow rates of 0.75 l.s-1. This is due to the water infiltration influence on the spatial distribution of strain fields. This result fits with field measurements. This methodology can easily be applied to the monitoring of landslide movements. As it gives relevant information on the spatial and temporal effects of various meteoric infiltrations, it can be applied to improve remedial protocols. This work was partly funded by the French National Program on Natural Hazards (PNRN) and Retina European Program. Guglielmi Y., 1999. Apport de la mesure des couplages hydromécaniques à la connaissance hydrogéologique des réservoirs fissurés. Habilitation à diriger des recherches, Université de Franche-Comté, E.A. 2642 Géosciences : Déformation, Écoulement, Transfert. 187 p. Noverraz F., BonnardC., Dupraz H., and Huguenin L., 1998. Grands glissements de versants et climat. Rapport final PNR 31, vdf hochschulverlag AG an der ETH Zürich, 314 p.

Study on the response of unsaturated soil slope based on the effects of rainfall intensity and slope angle

NASA Astrophysics Data System (ADS)

Ismail, Mohd Ashraf Mohamad; Hamzah, Nur Hasliza

2017-07-01

Rainfall has been considered as the major cause of the slope failure. The mechanism leading to slope failures included the infiltration process, surface runoff, volumetric water content and pore-water pressure of the soil. This paper describes a study in which simulated rainfall events were used with 2-dimensional soil column to study the response of unsaturated soil behavior based on different slope angle. The 2-dimensional soil column is used in order to demonstrate the mechanism of the slope failure. These unsaturated soil were tested with four different slope (15°, 25°, 35° and 45°) and subjected to three different rainfall intensities (maximum, mean and minimum). The following key results were obtained: (1) the stability of unsaturated soil decrease as the rainwater infiltrates into the soil. Soil that initially in unsaturated state will start to reach saturated state when rainwater seeps into the soil. Infiltration of rainwater will reduce the matric suction in the soil. Matric suction acts in controlling soil shear strength. Reduction in matric suction affects the decrease in effective normal stress, which in turn diminishes the available shear strength to a point where equilibrium can no longer be sustained in the slope. (2) The infiltration rate of rainwater decreases while surface runoff increase when the soil nearly achieve saturated state. These situations cause the soil erosion and lead to slope failure. (3) The steepness of the soil is not a major factor but also contribute to slope failures. For steep slopes, rainwater that fall on the soil surface will become surface runoff within a short time compare to the water that infiltrate into the soil. While for gentle slopes, water that becomes surface runoff will move slowly and these increase the water that infiltrate into the soil.

Movement of water infiltrated from a recharge basin to wells.

PubMed

O'Leary, David R; Izbicki, John A; Moran, Jean E; Meeth, Tanya; Nakagawa, Brandon; Metzger, Loren; Bonds, Chris; Singleton, Michael J

2012-01-01

Local surface water and stormflow were infiltrated intermittently from a 40-ha basin between September 2003 and September 2007 to determine the feasibility of recharging alluvial aquifers pumped for public supply, near Stockton, California. Infiltration of water produced a pressure response that propagated through unconsolidated alluvial-fan deposits to 125 m below land surface (bls) in 5 d and through deeper, more consolidated alluvial deposits to 194 m bls in 25 d, resulting in increased water levels in nearby monitoring wells. The top of the saturated zone near the basin fluctuates seasonally from depths of about 15 to 20 m. Since the start of recharge, water infiltrated from the basin has reached depths as great as 165 m bls. On the basis of sulfur hexafluoride tracer test data, basin water moved downward through the saturated alluvial deposits until reaching more permeable zones about 110 m bls. Once reaching these permeable zones, water moved rapidly to nearby pumping wells at rates as high as 13 m/d. Flow to wells through highly permeable material was confirmed on the basis of flowmeter logging, and simulated numerically using a two-dimensional radial groundwater flow model. Arsenic concentrations increased slightly as a result of recharge from 2 to 6 µg/L immediately below the basin. Although few water-quality issues were identified during sample collection, high groundwater velocities and short travel times to nearby wells may have implications for groundwater management at this and at other sites in heterogeneous alluvial aquifers. Ground Water © 2011, National Ground Water Association. Published 2011. This article is a U.S. Government work and is in the public domain in the USA.

Groundwater dynamics in a two-dimensional aquifer

NASA Astrophysics Data System (ADS)

Jules, Valentin; Devauchelle, Olivier; Lajeunesse, Eric

2017-11-01

During a rain event, water infiltrates into the ground where it flows slowly towards a river. The time scale and the geometry of this flow control the chemical composition and the discharge of the river. We use a tank filled with glass beads to simulate this process in a simplified laboratory experiment. A sprinkler pipe generates rain, which infiltrates into the porous material. Groundwater exits this laboratory aquifer through a side of the tank. Guérin et al. (2014) investigated the case of a quasi-horizontal flow. In nature, however, groundwater often follows non-horizontal flowlines. To create a vertical flow, we place the outlet of our experiment high above its bottom. We find that, during rainfall, the discharge Q increases as the rainfall rate R times the square root of time t (Q Rt 1 / 2). This laboratory aquifer thus responds linearly to the forcing. However, long after the rain has stopped, the discharge decreases as the inverse square of time (Q t-2), although linear systems of finite size typically relax exponentially. We investigate this surprising behavior using a combination of complex analysis and numerical methods.

Phase structure within a fracture network beneath a surface pond: Field experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

GLASS JR.,ROBERT J.; NICHOLL,M.J.

2000-05-09

The authors performed a simple experiment to elucidate phase structure within a pervasively fractured welded tuff. Dyed water was infiltrated from a surface pond over a 36 minute period while a geophysical array monitored the wetted region within vertical planes directly beneath. They then excavated the rock mass to a depth of {approximately}5 m and mapped the fracture network and extent of dye staining in a series of horizontal pavements. Near the pond the network was fully stained. Below, the phase structure immediately expanded and with depth, the structure became fragmented and complicated exhibiting evidence of preferential flow, fingers, irregularmore » wetting patterns, and varied behavior at fracture intersections. Limited transient geophysical data suggested that strong vertical pathways form first followed by increased horizontal expansion and connection within the network. These rapid pathways are also the first to drain. Estimates also suggest that the excavation captured from {approximately}10% to 1% or less of the volume of rock interrogated by the infiltration slug and thus the penetration depth could have been quite large.« less

Assessing the efficiency of a coastal Managed Aquifer Recharge (MAR) system in Cyprus.

PubMed

Tzoraki, Ourania; Dokou, Zoi; Christodoulou, George; Gaganis, Petros; Karatzas, George

2018-06-01

Managed Aquifer Recharge (MAR) is becoming an attractive water management option, with more than 223 sites operating in European countries. The quality of the produced water, available for drinking or irrigation processes is strongly depended on the aquifer's hydrogeochemical characteristics and on the MAR system design and operation. The objective of this project is the assessment of the operation efficiency of a MAR system in Cyprus. The coupling of alternative methodologies is used such as water quality monitoring, micro-scale sediment sorption experiments, simulation of groundwater flow and phosphate and copper transport in the subsurface using the FEFLOW model and evaluation of the observed change in the chemical composition of water due to mixing using the geochemical model PHREEQC. The above methodology is tested in the Ezousa MAR project in Cyprus, where treated effluent from the Paphos Waste Water Treatment Plant, is recharged into the aquifer through five sets of artificial ponds along the riverbed. Additionally, groundwater is pumped for irrigation purposes from wells located nearby. A slight attenuation of nutrients is observed, whereas copper in groundwater is overcoming the EPA standards. The FEFLOW simulations reveal no effective mixing in some intermediate infiltration ponds, which is validated by the inverse modeling simulation of the PHREEQC model. Based on the results, better control of the infiltration capacity of some of the ponds and increased travel times are some suggestions that could improve the efficiency of the system. Copyright © 2018 Elsevier B.V. All rights reserved.

Long-term reclaimed water application effects on phosphorus leaching potential in rapid infiltration basins.

PubMed

Moura, Daniel R; Silveira, Maria L; O'Connor, George A; Wise, William R

2011-09-01

Rapid infiltration basins (RIBs) are effective tools for wastewater treatment and groundwater recharge, but continuous application of wastewater can increase soil P concentrations and subsequently impact groundwater quality. The objectives of this study were to (1) investigate the effects of reclaimed water infiltration rate and "age" of RIBs on soil P concentrations at various depths, and (2) estimate the degree (percentage) of sorption equilibrium reached between effluent P and soil attained during reclaimed water application to different RIBs. The study was conducted in four contrasting cells of a RIB system with up to a 25 year history of secondary wastewater application. Soil samples were collected from 0 to 300 cm depth at 30 cm intervals and analyzed for water extractable phosphorus (WEP) and oxalate extractable P, Al, and Fe concentrations. Water extractable P and P saturation ratio (PSR) values were generally greater in the cells receiving reclaimed water compared to control soils, suggesting that reclaimed water P application can increase soil P concentrations and the risk of P movement to greater depths. Differences between treatment and control samples were more evident in cells with longer histories of reclaimed water application due to greater P loading. Data also indicated considerable spatial variability in WEP concentrations and PSR values, especially within cells from RIBs characterized by fast infiltration rates. This occurs because wastewater-P flows through surface soils much faster than the minimum time required for sorption equilibrium to occur. Studies should be conducted to investigate soil P saturation at deeper depths to assess possible groundwater contamination.

40 CFR 60.101a - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... tip to prevent oxygen infiltration (backflow) into the flare tip. For flares with no water seals, the... function of preventing oxygen infiltration (backflow) into the flare tip. [73 FR 35867, June 24, 2008, as...

40 CFR 60.101a - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... infiltration (backflow) into the flare tip. For flares with no water seals, the function of purge gas is... of preventing oxygen infiltration (backflow) into the flare tip. [73 FR 35867, June 24, 2008, as...

Residence time distributions of artificially infiltrated groundwater used for drinking water production

NASA Astrophysics Data System (ADS)

Popp, A. L.; Marçais, J.; Moeck, C.; Brennwald, M. S.; Kipfer, R.

2017-12-01

Public drinking water supply in urban areas is often challenging due to exposure to potential contamination and high water demands. At our study site, a drinking water supply field in Switzerland, managed aquifer recharge (MAR) was implemented to overcome an increasing water demand and decreasing water quality. Water from the river Rhine is put on a system of channels and ponds to artificially infiltrate and hence, increase the natural groundwater availability. The groundwater system consists of two overlying aquifers, with hydraulic connections related to fractures and faults. The deeper aquifer contains contaminants, which possibly originate from nearby landfills and industrial areas. The operating water works aims to pump recently infiltrated water only. However, we suspect that the pumped water contains a fraction of old water due to the fractured zones which serve as hydraulic connection between the two aquifers. With this study, we aim to better understand the mixing patterns between recently infiltrated water and old groundwater to evaluate the risk for contamination of the system. To reach our objective, we used a set of gas tracers (222Rn, 3H/3He, 4He) from fifteen wells distributed throughout the area to estimate the residence time distribution (RTD) of each well. We calibrated the RTD with a Binary Mixing Model, where the fraction of young groundwater is assumed to follow a Piston Flow Model. The older groundwater fraction is calibrated with a Dispersion Model. Our results reflect the heterogeneity of the system with some abstraction wells containing young water only and others showing an admixture of old water which can only be explained by a connection to the deeper aquifer. We also show that our results on calibrated RTDs are in accordance with other geochemical data such as electrical conductivity, major ions and pH. Our results will contribute to a sound conceptual flow and transport understanding and will help to optimize the water supply system.

Characterization by electrical and electromagnetic geophysical methods of the shallow hydrogeological system at Hebron (West Bank, Palestine) in a semi-arid zone

NASA Astrophysics Data System (ADS)

Sirhan, Asal; Hamidi, Mohammad O.

2012-09-01

Multi-electrode geo-electrical and transient electromagnetic surveys were carried out to characterize the nature of the subsurface infiltration zones (5 to 20 m) related to a series of groundwater outlets, and to reveal the geometry of the different aquifers at Bani-Naim, in the south-eastern foothills of the Hebron area, West Bank, Palestine. The purpose of the surveys was to understand the link between water storage/transfer and the characteristics of the geological formations. The strata in this semi-arid region are composed of alternate layers of chalky limestone, hard limestone, marl and chalk. A total of 30 ERT and 15 TDEM were conducted at Bani Naim-Jahir and Bani Naim-Birein. A correlation between the results indicates various infiltration pathways: fractures, feature heterogeneities, and porous chalk. The local heterogeneity on the eastern side were the major pathways for the water infiltration, whereas the thick marl layer underneath acts as a natural impermeable barrier preventing water from infiltrating deeper. A combination of the different geophysical results identified conductive features that correspond to the infiltration zones supplying the dug wells with water. Furthermore, it was established that the fractured chalk and porous chalky limestone act as an aquifer. A three-dimensional visualization of the resistivity allowed a useful reconstruction of the shallow hydrogeological system. Consequently, these studies contribute to regional sustainable development projects in this semi-arid region.

Influence of bioactive particles on the chemical-mechanical properties of experimental enamel resin infiltrants.

PubMed

Sfalcin, Ravana Angelini; Correr, Américo Bortolazzo; Morbidelli, Lucas Rafael; Araújo, Tatiany Gabrielle Freire; Feitosa, Victor Pinheiro; Correr-Sobrinho, Lourenço; Watson, Timothy Frederick; Sauro, Salvatore

2017-07-01

This study aimed at evaluating the chemophysical properties of experimental resin infiltrants (ERIs) doped with different bioactive particles. A control resin infiltrant (CR) was formulated using triethylene glycol dimethacrylate (TEGDMA) and ethoxylated bisphenol A dimethacrylate (BisEMA). Moreover, five experimental ERIs were also created by incorporating the following bioactive fillers (10 wt%) into the CR: hydroxyapatite (Hap), amorphous calcium phosphate (ACP), zinc-polycarboxylated bioactive glass (BAG-Zn), bioactive glass 45S5 (BAG 45S5), and calcium silicate modified with beta tricalcium phosphate (β-TCP). ICON® resin infiltrant was also used as control. All the ERIs used in this study were assessed for degree of conversion (DC), Knoop microhardness (KHN), softening ratio (SR), tensile cohesive strength (TCS), modulus of elasticity (E-modulus), water sorption (WS), and solubility (SL). Data were subjected to ANOVA and Tukey's test (α = 5%). ICON® presented the lowest DC, KHN, TCS, E-modulus, and SR. Incorporation of bioactive fillers into CR caused significant increase in the KHN. Conversely, no significant effect was observed on DC, TCS, and E-modulus. The resin infiltrant containing Hap showed a significant increase in softening ratio, while, ICON® presented the highest WS and SL. The WS of ACP-doped resin infiltrant was significantly higher than that of the Hap-doped infiltrant. The SL of the ACP-doped infiltrant was higher than CR BAG-Zn or BAG 45S5. The incorporation of bioactive particles into experimental resin infiltrants can improve the chemomechanical properties and reduce water sorption and solubility. Resin infiltrants doped with bioactive particles may improve the long-term performance of the treatment of white-spot lesions.

Hydrology Model Formulation within the Training Range Environmental Evaluation and Characterization System (TREECS)

DTIC Science & Technology

2014-02-01

Potential evapotranspiration is computed using the Thornthwaite Method. Infiltration is computed from a water balance. DISCLAIMER: The contents of...precipitation, rainfall, runoff, evapotranspiration , infiltration, and number of days with rainfall. A hydrology model was developed to estimate...temperatures. Potential evapotranspiration (PET) is computed using the Thornthwaite Method. Actual evapotranspiration (ET) and infiltration are computed from a

Analysis of Rainfall Infiltration Law in Unsaturated Soil Slope

PubMed Central

Zhang, Gui-rong; Qian, Ya-jun; Wang, Zhang-chun; Zhao, Bo

2014-01-01

In the study of unsaturated soil slope stability under rainfall infiltration, it is worth continuing to explore how much rainfall infiltrates into the slope in a rain process, and the amount of rainfall infiltrating into slope is the important factor influencing the stability. Therefore, rainfall infiltration capacity is an important issue of unsaturated seepage analysis for slope. On the basis of previous studies, rainfall infiltration law of unsaturated soil slope is analyzed. Considering the characteristics of slope and rainfall, the key factors affecting rainfall infiltration of slope, including hydraulic properties, water storage capacity (θ s - θ r), soil types, rainfall intensities, and antecedent and subsequent infiltration rates on unsaturated soil slope, are discussed by using theory analysis and numerical simulation technology. Based on critical factors changing, this paper presents three calculation models of rainfall infiltrability for unsaturated slope, including (1) infiltration model considering rainfall intensity; (2) effective rainfall model considering antecedent rainfall; (3) infiltration model considering comprehensive factors. Based on the technology of system response, the relationship of rainfall and infiltration is described, and the prototype of regression model of rainfall infiltration is given, in order to determine the amount of rain penetration during a rain process. PMID:24672332

Analysis of rainfall infiltration law in unsaturated soil slope.

PubMed

Zhang, Gui-rong; Qian, Ya-jun; Wang, Zhang-chun; Zhao, Bo

2014-01-01

In the study of unsaturated soil slope stability under rainfall infiltration, it is worth continuing to explore how much rainfall infiltrates into the slope in a rain process, and the amount of rainfall infiltrating into slope is the important factor influencing the stability. Therefore, rainfall infiltration capacity is an important issue of unsaturated seepage analysis for slope. On the basis of previous studies, rainfall infiltration law of unsaturated soil slope is analyzed. Considering the characteristics of slope and rainfall, the key factors affecting rainfall infiltration of slope, including hydraulic properties, water storage capacity (θs - θr), soil types, rainfall intensities, and antecedent and subsequent infiltration rates on unsaturated soil slope, are discussed by using theory analysis and numerical simulation technology. Based on critical factors changing, this paper presents three calculation models of rainfall infiltrability for unsaturated slope, including (1) infiltration model considering rainfall intensity; (2) effective rainfall model considering antecedent rainfall; (3) infiltration model considering comprehensive factors. Based on the technology of system response, the relationship of rainfall and infiltration is described, and the prototype of regression model of rainfall infiltration is given, in order to determine the amount of rain penetration during a rain process.

Borehole environmental tracers for evaluating net infiltration and recharge through desert bedrock

USGS Publications Warehouse

Heilweil, V.M.; Solomon, D.K.; Gardner, P.M.

2006-01-01

Permeable bedrock aquifers in arid regions are being increasingly developed as water supplies, yet little is generally known about recharge processes and spatial and temporal variability. Environmental tracers from boreholes were used in this study to investigate net infiltration and recharge to the fractured Navajo Sandstone aquifer. Vadose zone tracer profiles at the Sand Hollow study site in southwestern Utah look similar to those of desert soils at other sites, indicating the predominance of matrix flow. However, recharge rates are generally higher in the Navajo Sandstone than in unconsolidated soils in similar climates because the sandstone matrix allows water movement but not root penetration. Water enters the vadose zone either as direct infiltration of precipitation through exposed sandstone and sandy soils or as focused infiltration of runoff. Net infiltration and recharge exhibit extreme spatial variability. High-recharge borehole sites generally have large amounts of vadose zone tritium, low chloride concentrations, and small vadose zone oxygen-18 evaporative shifts. Annual net-infiltration and recharge rates at different locations range from about 1 to 60 mm as determined using vadose zone tritium, 0 to 15 mm using vadose zone chloride, and 3 to 60 mm using groundwater chloride. Environmental tracers indicate a cyclical net-infiltration and recharge pattern, with higher rates earlier in the Holocene and lower rates during the late Holocene, and a return to higher rates during recent decades associated with anomalously high precipitation during the latter part of the 20th century. The slightly enriched stable isotopic composition of modern groundwater indicates this recent increase in precipitation may be caused by a stronger summer monsoon or winter southern Pacific El Nin??o storm track. ?? Soil Science Society of America.

From rain tanks to catchments: Use of low-impact development to address hydrologic symptoms of the urban stream syndrome

NASA Astrophysics Data System (ADS)

Grant, S. B.

2015-12-01

Catchment urbanization perturbs the water and sediment budgets of streams, degrades stream health and function, and causes a constellation of flow, water quality and ecological symptoms collectively known as the urban stream syndrome. Low-impact development (LID) technologies address the hydrologic symptoms of the urban stream syndrome by mimicking natural flow paths and restoring a natural water balance. Over annual time scales, the volumes of storm water that should be infiltrated and harvested can be estimated from a catchment-scale water-balance given local climate conditions and pre-urban land cover. For all but the wettest regions of the world, the water balance predicts a much larger volume of storm water runoff should be harvested than infiltrated to restore stream hydrology to a pre-urban state. Efforts to prevent or reverse hydrologic symptoms associated with the urban stream syndrome will therefore require: (1) selecting the right mix of LID technologies that provide regionally tailored ratios of storm water harvesting and infiltration; (2) integrating these LID technologies into next-generation drainage systems; (3) maximizing potential co-benefits including water supply augmentation, flood protection, improved water quality, and urban amenities; and (4) long-term hydrologic monitoring to evaluate the efficacy of LID interventions.

Effect of vegetation construction on runoff and sediment yield and runoff erosion ability on slope surface

NASA Astrophysics Data System (ADS)

Yang, Chun Xia; Xiao, PeiQing; Li, Li; Jiao, Peng

2018-06-01

Land consolidation measures affected the underlying surface erosion environment during the early stage of vegetation construction, and then had an impact on rainfall infiltration, erosion and sediment yield. This paper adopted the field simulated rainfall experiments to analyze the function that pockets site preparation measures affected on rainfall infiltration, runoff sediment yield and runoff erosion ability. The results showed that, the measures can delay the rainfall runoff formation time of the slope by 3'17" and 1'04" respectively. Compared with the same condition of the bare land and natural grassland. The rainfall infiltration coefficient each increased by 76.47% and 14.49%, and infiltration rate increased by 0.26 mm/min and 0.11mm/min respectively; The amount of runoff and sediment yield were reduced because of the pockets site preparation. The amount of runoff reducing rate were 33.51% and 30.49%, and sediment reduction rate were 81.35% and 65.66%, The sediment concentration was decreased by 71.99% and 50.58%; Runoff velocity of bare slope and natural grassland slope decreased by 38.12% and 34.59% respectively after pockets site preparation . The runoff erosion rate decreased by 67.92% and 79.68% respectively. The results will have a great significance for recognizing the effect of water and sediment reduction about vegetation and the existence of its plowing measures at the early period of restoration.

Transpiration and root development of urban trees in structural soil stormwater reservoirs.

PubMed

Bartens, Julia; Day, Susan D; Harris, J Roger; Wynn, Theresa M; Dove, Joseph E

2009-10-01

Stormwater management that relies on ecosystem processes, such as tree canopy interception and rhizosphere biology, can be difficult to achieve in built environments because urban land is costly and urban soil inhospitable to vegetation. Yet such systems offer a potentially valuable tool for achieving both sustainable urban forests and stormwater management. We evaluated tree water uptake and root distribution in a novel stormwater mitigation facility that integrates trees directly into detention reservoirs under pavement. The system relies on structural soils: highly porous engineered mixes designed to support tree root growth and pavement. To evaluate tree performance under the peculiar conditions of such a stormwater detention reservoir (i.e., periodically inundated), we grew green ash (Fraxinus pennsylvanica Marsh.) and swamp white oak (Quercus bicolor Willd.) in either CUSoil or a Carolina Stalite-based mix subjected to three simulated below-system infiltration rates for two growing seasons. Infiltration rate affected both transpiration and rooting depth. In a factorial experiment with ash, rooting depth always increased with infiltration rate for Stalite, but this relation was less consistent for CUSoil. Slow-drainage rates reduced transpiration and restricted rooting depth for both species and soils, and trunk growth was restricted for oak, which grew the most in moderate infiltration. Transpiration rates under slow infiltration were 55% (oak) and 70% (ash) of the most rapidly transpiring treatment (moderate for oak and rapid for ash). We conclude this system is feasible and provides another tool to address runoff that integrates the function of urban green spaces with other urban needs.

Intra-basin variability of snowmelt water balance calculations in a subarctic catchment

NASA Astrophysics Data System (ADS)

McCartney, Stephen E.; Carey, Sean K.; Pomeroy, John W.

2006-03-01

The intra-basin variability of snowmelt and melt-water runoff hydrology in an 8 km2 subarctic alpine tundra catchment was examined for the 2003 melt period. The catchment, Granger Creek, is within the Wolf Creek Research Basin, Yukon, which is typical of mountain subarctic landscapes in northwestern Canada. The study catchment was segmented into nine internally uniform zones termed hydrological response units (HRUs) based on their similar hydrological, physiographic, vegetation and soil properties. Snow accumulation exhibited significant variability among the HRUs, with greatest snow water equivalent in areas of tall shrub vegetation. Melt began first on southerly exposures and at lower elevations, yet average melt rates for the study period varied little among HRUs with the exception of those with steep aspects. In HRUs with capping organic soils, melt water first infiltrated this surface horizon, satisfying its storage capacity, and then percolated into the frozen mineral substrate. Infiltration and percolation into frozen mineral soils was restricted where melt occurred rapidly and organic soils were thin; in this case, melt-water delivery rates exceeded the frozen mineral soil infiltration rate, resulting in high runoff rates. In contrast, where there were slower melt rates and thick organic soils, infiltration was unlimited and runoff was suppressed. The snow water equivalent had a large impact on runoff volume, as soil storage capacity was quickly surpassed in areas of deep snow, diverting the bulk of melt water laterally to the drainage network. A spatially distributed water balance indicated that the snowmelt freshet was primarily controlled by areas with tall shrub vegetation that accumulate large quantities of snow and by alpine areas with no capping organic soils. The intra-basin water balance variability has important implications for modelling freshet in hydrological models.

Evaluation of Water Quality Renovation by Advanced Soil-Based Wastewater Treatment Systems

NASA Astrophysics Data System (ADS)

Cooper, J.; Loomis, G.; Kalen, D.; Boving, T.; Morales, I.; DeLuca, J.; Amador, J.

2013-12-01

25% of US households utilize onsite wastewater treatment systems (OWTS) for wastewater management. Advanced technologies were designed to overcome the inadequate wastewater treatment by conventional OWTS in critical shallow water table areas, such as coastal zones, in order to protect ground water quality. In addition to the septic tank and soil drainfield that comprise a conventional OWTS, advanced systems claim improved water renovation with the addition of sand filtration, timed dosing controls, and shallow placement of the infiltrative zone. We determined water quality renovation functions under current water table and temperature conditions, in anticipation of an experiment to measure OWTS response to a climate change scenario of 30-cm increase in water table elevation and 4C temperature increase. Replicate (n=3) intact soil mesocosms were used to evaluate the effectiveness of drainfields with a conventional wastewater delivery (pipe-and-stone) compared to two types of pressurized, shallow narrow drainfield. Results under steady state conditions indicate complete removal of fecal coliform bacteria, phosphorus and BOD by all soil-based systems. By contrast, removal of total nitrogen inputs was 16% in conventional and 11% for both advanced drainfields. Effluent waters maintained a steady state pH between 3.2 - 3.7 for all technologies. Average DO readings were 2.9mg/L for conventional drainfield effluent and 4.6mg/L for advanced, showing the expected oxygen uptake with shallow placement of the infiltrative zone. The conventional OWTS is outperforming the advanced with respect to nitrogen removal, but renovating wastewater equivalently for all other contaminants of concern. The results of this study are expected to facilitate development of future OWTS regulation and planning guidelines, particularly in coastal zones and in the face of a changing climate.

The Eco-Hydrological Role of Physical Surface Sealing in Dry Environments

NASA Astrophysics Data System (ADS)

Sela, Shai; Svoray, Tal; Assouline, Shmuel

2016-04-01

Soil surface sealing is a widespread natural process in dry environments occurring frequently in bare soil areas between vegetation patches. The low hydraulic conductivity that characterizes the seal layer reduces both infiltration and evaporation fluxes from the soil, and thus has the potential to affect local vegetation water availability and consequently transpiration rates. This effect is investigated here using two separate physically based models - a runoff model, and a root water uptake model. High resolution rainfall data is used to demonstrate the seal layer effect on runoff generation and vegetation water availability, while the seal layer effect on vegetation water uptake is studied using a long-term climatic dataset (44 years) from three dry sites presenting a climatic gradient in the Negev Desert, Israel. The Feddes water uptake parameters for the dominant shrub at the study site (Sarcopoterium spinosum) were acquired using an inverse calibration procedure using data from a lysimeter experiment. The results indicate that the presence of surface sealing increases significantly vegetation water availability through runoff generation. Following water infiltration, the shrub transpiration generally increases if the shrub is surrounded by a seal layer, but this effect can switch from positive to negative depending on initial soil water content, rainfall intensity, and the duration of the subsequent drying intervals. These factors have a marked effect on inter-annual variability of the seal layer effect on the shrub transpiration, which on average was found to be 26% higher under sealed conditions than in the case of unsealed soil surfaces. These results shed light on the importance of surface sealing on the eco-hydrology of dry environments and its contribution to the resilience of woody vegetation.

Numerical simulation of water flow and Nitrate transport through variably saturated porous media in laboratory condition using HYDRUS 2D

NASA Astrophysics Data System (ADS)

Jahangeer, F.; Gupta, P. K.; Yadav, B. K.

2017-12-01

Due to the reducing availability of water resources and the growing competition for water between residential, industrial, and agricultural users, increasing irrigation efficiency, by several methods like drip irrigation, is a demanding concern for agricultural experts. The understanding of the water and contaminants flow through the subsurface is needed for the sustainable irrigation water management, pollution assessment, polluted site remediation and groundwater recharge. In this study, the Windows-based computer software package HYDRUS-2D, which numerically simulates water and solute movement in two-dimensional, variably-saturated porous media, was used to evaluate the distribution of water and Nitrate in the sand tank. The laboratory and simulation experiments were conducted to evaluate the role of drainage, recharge flux, and infiltration on subsurface flow condition and subsequently, on nitrate movement in the subsurface. The water flow in the unsaturated zone model by Richards' equation, which was highly nonlinear and its parameters were largely dependent on the moisture content and pressure head of the partially saturated zone. Following different cases to be considered to evaluate- a) applying drainage and recharge flux to study domains, b) transient infiltration in a vertical soil column and c) subsequently, nitrate transport in 2D sand tank setup. A single porosity model was used for the simulation of water and nitrate flow in the study domain. The results indicate the transient water table position decreases as the time increase significantly by applying drainage flux at the bottom. Similarly, the water table positions in study domains increasing in the domain by applying recharge flux. Likewise, the water flow profile shows the decreasing water table elevation with increasing water content in the vertical domain. Moreover, the nitrate movement was dominated by advective flux and highly affected by the recharge flux in the vertical direction. The findings of the study help to enhance the understanding of the sustainable soil-water resources management and agricultural practices.

Time-lapse gravity data for monitoring and modeling artificial recharge through a thick unsaturated zone

USGS Publications Warehouse

Kennedy, Jeffrey R.; Ferre, Ty P.A.; Creutzfeldt, Benjamin

2016-01-01

Groundwater-level measurements in monitoring wells or piezometers are the most common, and often the only, hydrologic measurements made at artificial recharge facilities. Measurements of gravity change over time provide an additional source of information about changes in groundwater storage, infiltration, and for model calibration. We demonstrate that for an artificial recharge facility with a deep groundwater table, gravity data are more sensitive to movement of water through the unsaturated zone than are groundwater levels. Groundwater levels have a delayed response to infiltration, change in a similar manner at many potential monitoring locations, and are heavily influenced by high-frequency noise induced by pumping; in contrast, gravity changes start immediately at the onset of infiltration and are sensitive to water in the unsaturated zone. Continuous gravity data can determine infiltration rate, and the estimate is only minimally affected by uncertainty in water-content change. Gravity data are also useful for constraining parameters in a coupled groundwater-unsaturated zone model (Modflow-NWT model with the Unsaturated Zone Flow (UZF) package).

Time-lapse gravity data for monitoring and modeling artificial recharge through a thick unsaturated zone

NASA Astrophysics Data System (ADS)

Kennedy, Jeffrey; Ferré, Ty P. A.; Creutzfeldt, Benjamin

2016-09-01

Groundwater-level measurements in monitoring wells or piezometers are the most common, and often the only, hydrologic measurements made at artificial recharge facilities. Measurements of gravity change over time provide an additional source of information about changes in groundwater storage, infiltration, and for model calibration. We demonstrate that for an artificial recharge facility with a deep groundwater table, gravity data are more sensitive to movement of water through the unsaturated zone than are groundwater levels. Groundwater levels have a delayed response to infiltration, change in a similar manner at many potential monitoring locations, and are heavily influenced by high-frequency noise induced by pumping; in contrast, gravity changes start immediately at the onset of infiltration and are sensitive to water in the unsaturated zone. Continuous gravity data can determine infiltration rate, and the estimate is only minimally affected by uncertainty in water-content change. Gravity data are also useful for constraining parameters in a coupled groundwater-unsaturated zone model (Modflow-NWT model with the Unsaturated Zone Flow (UZF) package).

Numerical Analysis of Infiltration Into a Sand Profile Bounded by a Capillary Fringe

NASA Astrophysics Data System (ADS)

Curtis, Alan A.; Watson, Keith K.

1980-04-01

The rapid response sometimes observed in a tile drain system following surface ponding of water is discussed in terms of the air compressibility effect. An earlier numerical study describing water movement into a bounded profile with a lower boundary impermeable to the passage of both air and water is reviewed with particular reference to the validity of the time-dependent boundary condition transformation used in simulating the inhibiting effects of the air pressure increase on infiltration. The extension of the transformation approach to a profile bounded by a capillary fringe is then considered in detail, and the results of numerical analyses are presented for infiltration into two columns of a fine sand initially in hydraulic equilibrium from a prior gravity drainage regime. The shorter column develops a steady state flow condition at short times which is consistent with earlier experimental findings. In contrast, the pressure of the entrapped air in the longer column gradually increases as infiltration proceeds until the analysis is terminated when air escape through the lower boundary is imminent.

On the value of electrical resistivity tomography for monitoring leachate injection in solid state anaerobic digestion plants at farm scale.

PubMed

Degueurce, Axelle; Clément, Rémi; Moreau, Sylvain; Peu, Pascal

2016-10-01

Agricultural waste is a valuable resource for solid state anaerobic digestion (SSAD) thanks to its high solid content (>15%). Batch mode SSAD with leachate recirculation is particularly appropriate for such substrates. However, for successful degradation, the leachate must be evenly distributed through the substrate to improve its moisture content. To study the distribution of leachate in agricultural waste, electrical resistivity tomography (ERT) was performed. First, laboratory-scale experiments were conducted to check the reliability of this method to monitor infiltration of the leachate throughout the solid. Two representative mixtures of agricultural wastes were prepared: a "winter" mixture, with cattle manure, and a "summer" mixture, with cattle manure, wheat straw and hay. The influence of density and water content on electrical resistivity variations was assessed in the two mixtures. An increase in density was found to lead to a decrease in electrical resistivity: at the initial water content, resistivity decreased from 109.7 to 19.5Ω·m in the summer mixture and from 9.8 to 2.7Ω·m in the "winter" mixture with a respective increased in density of 0.134-0.269, and 0.311-0.577. Similarly, resistivity decreased with an increase in water content: for low densities, resistivity dropped from 109.7 to 7.1Ω·m and 9.8 to 4.0Ω·m with an increase in water content from 64 to 90w% and 74 to 93w% for "summer" and "winter" mixtures respectively. Second, a time-lapse ERT was performed in a farm-scale SSAD plant to monitor leachate infiltration. Results revealed very heterogeneous distribution of the leachate in the waste, with two particularly moist areas around the leachate injection holes. However, ERT was successfully applied in the SSAD plant, and produced a reliable 3D map of leachate infiltration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Response mechanism of post-earthquake slopes under heavy rainfall

NASA Astrophysics Data System (ADS)

Qiu, Hong-zhi; Kong, Ji-ming; Wang, Ren-chao; Cui, Yun; Huang, Sen-wang

2017-07-01

This paper uses the catastrophic landslide that occurred in Zhongxing Town, Dujiangyan City, as an example to study the formation mechanism of landslides induced by heavy rainfall in the post-Wenchuan earthquake area. The deformation characteristics of a slope under seismic loading were investigated via a shaking table test. The results show that a large number of cracks formed in the slope due to the tensile and shear forces of the vibrations, and most of the cracks had angles of approximately 45° with respect to the horizontal. A series of flume tests were performed to show how the duration and intensity of rainfall influence the responses of the shaken and non-shaken slopes. Wetting fronts were recorded under different rainfall intensities, and the depth of rainfall infiltration was greater in the shaken slope than in the non-shaken slope because the former experienced a greater extreme rainfall intensity under the same early rainfall and rainfall duration conditions. At the beginning of the rainfall infiltration experiment, the pore water pressure in the slope was negative, and settling occurred at the top of the slope. With increasing rainfall, the pore water pressure changed from negative to positive, and cracks were observed on the back surface of the slope and the shear outlet of the landslide on the front of the slope. The shaken slope was more susceptible to crack formation than the non-shaken slope under the same rainfall conditions. A comparison of the responses of the shaken and non-shaken slopes under heavy rainfall revealed that cracks formed by earthquakes provided channels for infiltration. Soil particles in the cracks of slopes were washed away, and the pore water pressure increased rapidly, especially the transient pore water pressure in the slope caused by short-term concentrated rainfall which decreased rock strength and slope stability.

Artificial sweeteners as waste water markers in a shallow unconfined aquifer

NASA Astrophysics Data System (ADS)

Bichler, Andrea; Muellegger, Christian; Hofmann, Thilo

2013-04-01

One key factor in groundwater quality management is the knowledge of flow paths and recharge. In coupled ground- and surface water systems the understanding of infiltration processes is therefore of paramount importance. Recent studies show that artificial sweeteners - which are used as sugar substitutes in food and beverages - are suitable tracers for domestic wastewater in the aquatic environment. As most rivers receive sewage discharges, artificial sweeteners might be used for tracking surface waters in groundwater. In this study artificial sweeteners are used in combination with conventional tracers (inert anions Cl-, SO42-, stable water isotopes δ18O, δ2H) to identify river water infiltration and the influence of waste water on a shallow unconfined aquifer used for drinking water production. The investigation area is situated in a mesoscale alpine head water catchment. The alluvial aquifer consists of quaternary gravel deposits and is characterized by high hydraulic permeability (kfmax 5 x 10-2 ms-1), high flow velocities (vmax 250 md-1) and a considerable productivity (2,5 m3s-1). A losing stream follows the aquifer in close proximity and is susceptible to infiltrate substantial volumes of water into the alluvial sediments. Water sampling campaigns in March and July 2012 confirmed the occurrence of artificial sweeteners (Acesulfam ACE, Sucralose SUC, Saccharin SAC and Cyclamat CYC) at the investigated site. The local sewage treatment plant was identified as point source of artificial sweeteners in the river water, with ACE concentrations up to 0,6 μgL-1. ACE concentrations in groundwater where approximately of one order of magnitude lower: ACE was present in 33 out of 40 sampled groundwater wells with concentrations up to 0,07 μgL-1, thus indicating considerable influence of sewage water loaded surface water throughout the aquifer. Elevated concentrations of ACE and SAC in single observation wells denote other sources of locally limited contamination. Also, the temporal variability of sweeteners in surface water and the drinking water production well is compared with other tracers. ACE, Cl-and SO42- exhibit similar patterns in the river water. However, this behaviour cannot be observed in the production well, where ACE concentrations are varying compared to Cl- and SO42-.This suggests that the production well does receive groundwater being infiltrated prior to the sewage water treatment plant. Time series analysis of 18O, δ2H will give more insight in travel times and the location of infiltration zones.

On-Farm, Almond Orchard Flooding as a Viable Aquifer Recharge Alternative

NASA Astrophysics Data System (ADS)

Ulrich, C.; Nico, P. S.; Wu, Y.; Newman, G. A.; Conrad, M. E.; Dahlke, H. E.

2017-12-01

In 2014, California legislators passed the Sustainable Groundwater Management Act (SGMA), which requires groundwater sustainability agencies (areas) to identify/prioritize water basins, develop current and projected water use/needs, develop a groundwater management plan, develop fees, etc. One of the challenges for implementing SGMA is the lack of data that can support alternative groundwater recharge methods such as on-farm flooding. Prior to anthropogenic river control, river floodplains captured excess water during overbank flow in the rainy season in the CA central valley. Today levees and canals strategically route rainy season high flows to the delta/ocean when irrigation water is not needed. Utilizing farmland once again as infiltration basins for groundwater banking and aquifer recharge could be a viable answer to California's depleted central valley aquifers. Prior to 2017, U.C. Davis had partnered with the Almond Board of California (ABC) and local growers to study the efficacy of agricultural flooding and the effects on annual almond crops (. LBNL joined this team to help understand the conveyance of recharge water, using electrical resistivity tomography (ERT), into the subsurface (i.e. localized fast paths, depth of infiltration, etc.) during flooding events. The fate of the recharge water is what is significant to understanding the viability of on-farm flooding as an aquifer recharge option. In this study two orchards (in Delhi and Modesto, CA), each approximately 2 acres, were flooded during the almond tree dormant period (January), to recharge 2 acre/ft of water into the local aquifers. ERT was used to characterize (soil structure) and monitor water infiltration over a single flooding event to investigate the fate of applied water. Data were collected every hour prior to flooding (baseline), during, and after all flood water had infiltrated (about 5 days total). Our time-lapse ERT results show a heterogeneous soil structure that leads to non-uniform infiltration (fast paths) and water recharge well below the root zone to a depth below 15m (45ft) at both study sites. These results advocate the use of on-farm flooding as a viable option for groundwater recharge of local aquifers and its usefulness given existing infrastructure and potential to divert water as it heads to the delta/ocean.

Field Validation of Toxicity Tests to Evaluate the Potential for Beneficial Use of Produced Water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph Bidwell; Jonathan Fisher; Naomi Cooper

2008-03-31

This study investigated potential biological effects of produced water contamination derived from occasional surface overflow and possible subsurface intrusion at an oil production site along the shore of Skiatook Lake, Oklahoma. We monitored basic chemistry and acute toxicity to a suite of standard aquatic test species (fathead minnow-Pimephales promelas, Daphnia pulex, Daphnia magna, and Ceriodaphnia dubia) in produced water and in samples taken from shallow groundwater wells on the site. Toxicity identification evaluations and ion toxicity modeling were used to identify toxic constituents in the samples. Lake sediment at the oil production site and at a reference site were alsomore » analyzed for brine intrusion chemically and by testing sediment toxicity using the benthic invertebrates, Chironomus dilutus, and Hyallela azteca. Sediment quality was also assessed with in situ survival and growth studies with H. azteca and the Asian clam, Corbicula fluminea, and by benthic macroinvertebrate community sampling. The produced water was acutely toxic to the aquatic test organisms at concentrations ranging from 1% to 10% of the whole produced water sample. Toxicity identification evaluation and ion toxicity modeling indicated major ion salts and hydrocarbons were the primary mixture toxicants. The standardized test species used in the laboratory bioassays exhibited differences in sensitivity to these two general classes of contaminants, which underscores the importance of using multiple species when evaluating produced water toxicity. Toxicity of groundwater was greater in samples from wells near a produced water injection well and an evaporation pond. Principle component analyses (PCA) of chemical data derived from the groundwater wells indicated dilution by lake water and possible biogeochemical reactions as factors that ameliorated groundwater toxicity. Elevated concentrations of major ions were found in pore water from lake sediments, but toxicity from these ions was limited to sediment depths of 10 cm or greater, which is outside of the primary zone of biological activity. Further, exposure to site sediments did not have any effects on test organisms, and macroinvertebrate communities did not indicate impairment at the oil production site as compared to a reference site. In situ experiments with H. azteca and C. fluminea, indicated a sublethal site effect (on growth of both species), but these could not be definitively linked with produced water infiltration. Severe weather conditions (drought followed by flooding) negatively influenced the intensity of lake sampling aimed at delineating produced water infiltration. Due to the lack of clear evidence of produced water infiltration into the sub-littoral zone of the lake, it was not possible to assess whether the laboratory bioassays of produced water effectively indicate risk in the receiving system. However, the acutely toxic nature of the produced water and general lack of biological effects in the lake at the oil production site suggest minimal to no produced water infiltration into surficial lake sediments and the near-shore water column. This study was able to demonstrate the utility of ion toxicity modeling to support data from toxicity identification evaluations aimed at identifying key toxic constituents in produced water. This information could be used to prioritize options for treating produced water in order to reduce toxic constituents and enhance options for reuse. The study also demonstrated how geographic information systems, toxicity modeling, and toxicity assessment could be used to facilitate future site assessments.« less

Temporal evolution of water repellency and preferential flow in the post-fire

NASA Astrophysics Data System (ADS)

Alanís, Nancy; Jordán, Antonio; Zavala, Lorena M.

2015-04-01

Forest fires usually intensify erosive process due to the reduction of vegetation cover and degradation of aggregation in the topsoil. Another common effect of wildifres is the development of soil water repellency, which in turn favors the formation of runoff, inhibiting or delaying infiltration. Under these conditions, infiltration occurs only when ponded water or runoff flow finds macropores and cracks in the soil surface, producing preferential flow pathways. When water infiltrates through these paths, a significant portion of the soil remains dry, limiting the supply of nutrients to the roots, favoring the rapid leaching of nutrients and agrochemicals, and other impacts on flora and hydrological processes at hillslope- or basin-scale. The existence of irregular wetting fronts has been observed frequently in burned or unburned water repellent soils. Although some authors have suggested that preferential flow paths may be more or less permanent in the case of unburned soils, the temporal evolution of preferential flow has been rarely studied in burned soils during the post-fire, after water repellency decreases or disappears. This research focuses on the temporal evolution of water repellency and preferential flows in an area affected by fire.

Scaling of hydrologic and erosion parameters derived from rainfall simulation

NASA Astrophysics Data System (ADS)

Sheridan, Gary; Lane, Patrick; Noske, Philip; Sherwin, Christopher

2010-05-01

Rainfall simulation experiments conducted at the temporal scale of minutes and the spatial scale of meters are often used to derive parameters for erosion and water quality models that operate at much larger temporal and spatial scales. While such parameterization is convenient, there has been little effort to validate this approach via nested experiments across these scales. In this paper we first review the literature relevant to some of these long acknowledged issues. We then present rainfall simulation and erosion plot data from a range of sources, including mining, roading, and forestry, to explore the issues associated with the scaling of parameters such as infiltration properties and erodibility coefficients.

Alteration of natural (37)Ar activity concentration in the subsurface by gas transport and water infiltration.

PubMed

Guillon, Sophie; Sun, Yunwei; Purtschert, Roland; Raghoo, Lauren; Pili, Eric; Carrigan, Charles R

2016-05-01

High (37)Ar activity concentration in soil gas is proposed as a key evidence for the detection of underground nuclear explosion by the Comprehensive Nuclear Test-Ban Treaty. However, such a detection is challenged by the natural background of (37)Ar in the subsurface, mainly due to Ca activation by cosmic rays. A better understanding and improved capability to predict (37)Ar activity concentration in the subsurface and its spatial and temporal variability is thus required. A numerical model integrating (37)Ar production and transport in the subsurface is developed, including variable soil water content and water infiltration at the surface. A parameterized equation for (37)Ar production in the first 15 m below the surface is studied, taking into account the major production reactions and the moderation effect of soil water content. Using sensitivity analysis and uncertainty quantification, a realistic and comprehensive probability distribution of natural (37)Ar activity concentrations in soil gas is proposed, including the effects of water infiltration. Site location and soil composition are identified as the parameters allowing for a most effective reduction of the possible range of (37)Ar activity concentrations. The influence of soil water content on (37)Ar production is shown to be negligible to first order, while (37)Ar activity concentration in soil gas and its temporal variability appear to be strongly influenced by transient water infiltration events. These results will be used as a basis for practical CTBTO concepts of operation during an OSI. Copyright © 2016 Elsevier Ltd. All rights reserved.

Long term continuous field survey to assess nutrient emission impact from irrigated paddy field into river catchment

NASA Astrophysics Data System (ADS)

Kogure, Kanami; Aichi, Masaatsu; Zessner, Matthias

2017-04-01

In order to achieve good river environment, it is very important to understand and to control nutrient behavior such as Nitrogen and Phosphorus. As we could reduce impact from urban and industrial activities by wastewater treatment, pollution from point sources are likely to be controlled. Besides them, nutrient emission from agricultural activity is dominant pollution source into the river system. In many countries in Asia and Africa, rice is widely cultivated and paddy field covers large areas. In Japan 54% of its arable land is occupied with irrigated paddy field. While paddy field can deteriorate river water quality due to fertilization, it is also suggested that paddy field can purify water. We carried out field survey in middle reach of the Tone River Basin with focus on a paddy field IM. The objectives of the research are 1) understanding of water and nutrient balance in paddy field, 2) data collection for assessing nutrient emission. Field survey was conducted from June 2015 to October 2016 covering two flooding seasons in summer. In our measurement, all input and output were measured regarding water, N and P to quantify water and nutrient balance in the paddy field. By measuring water quality and flow rate of inflow, outflow, infiltrating water, ground water and flooding water, we tried to quantitatively understand water, N and P cycle in a paddy field including seasonal trends, and changes accompanied with rainy events and agricultural activities like fertilization. Concerning water balance, infiltration rate was estimated by following equation. Infiltration=Irrigation water + Precipitation - Evapotranspiration -Outflow We estimated mean daily water balance during flooding season. Infiltration is 11.9mm/day in our estimation for summer in 2015. Daily water reduction depth (WRD) is sum of Evapotranspiration and Infiltration. WRD is 21.5mm/day in IM and agrees with average value in previous research. Regarding nutrient balance, we estimated an annual N and P balance. N and P surplus are calculated by difference between input and output in a paddy field. As to nutrient balance in 2015 surplus shows minus value between input as fertilizer and output as rice product. However, by taking account of input via irrigation water as nutrient source, N and P input and output balance with errors by 9% and 14%. Results of long term continuous survey suggest that irrigation water is one of nutrient sources in rice cultivation.

Seasonal changes of the infiltration rates in urban parks of Valencia City, Eastern Spain

NASA Astrophysics Data System (ADS)

Cerdà, Artemi; Keesstra, Saskia; Burguet, María; Pereira, Paulo; Esteban Lucas-Borja, Manuel; Martinez-Murillo, Juan F.

2016-04-01

Infiltration is a key process of the hydrological cycle. Infiltration also controls the soil water resources, and the development of the vegetation, and moreover, in the Mediterranean, determines the runoff generation (Cerdà, 1996; 1997; 2001). In the Mediterranean, the infiltration in forest soils shows high spatial variability and seasonal and temporal changes (Cerdà, 1999; Bodí and Cerdà, 2009) and is being affected by forest fires (Cerdà, 1998), which introduce a new temporal change in the seasonality of the infiltration rates. Although the forest soils are well assessed, there is no information about the infiltration in urban areas in Mediterranean cities. The Mediterranean dense urban systems use to be treated as impermeable areas. However, the cities show areas covered by vegetation and with soils that allow the rainfall to infiltrate. Those areas are mainly the parks. In order to shed some light on the infiltration capacity of the soils of the urban area of Valencia city 30 rainfall simulations experiments (Cerdà, 1996) and 90 ring infiltrometer (10 cm diameter) measurements were carried out in January 2011, and they were repeated in July 2011, to compare wet (19.4 % of soil moisture) and dry (5.98 % of soil moisture) soils. The infiltration curves where fitted to the Horton (1933) equation and they lasted for 1 hour. The results show that the infiltration is 11 times higher when measured with ring infiltrometer than with the simulated rainfall at 55 mmh-1, and that the infiltration rates where higher in summer than in winter: 2.01 higher for the ring infiltrometer, and 1.45 higher when measured with the rainfall simulator. In comparison to the soils from the forest areas, the infiltration rate in the gardens were lower, with values of 10.23 and 21.65 mm h-1 in average for winter and summer when measured with the rainfall simulator. Similar results were found with the ring infiltrometer. It was also found a clear relationship between the vegetation cover and the infiltration, with high infiltration rates with the grass covers. This is due to the higher infiltration rates of the soils with roots and due to the impact of plant stems on the runoff generation (Wang et al., 2015; Zhao et al., 2015). The importance of the vegetation on the soil infiltration capacity in the gardens of Valencia is a key factor to reduce the runoff sediment concentration such as was found at different scales (Keesstra et al., 2007; Nanko et al., 2015; Pereira et al, 2015; Prosdocimi et al., 2016) Acknowledgements The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 603498 (RECARE project). References Cerdà, A. 1996. Seasonal variability of infiltration rates under contrasting slope conditions in southeast Spain. Geoderma, 69 (3-4), 217-232. Cerdà, A. 1997. Seasonal changes of the infiltration rates in a mediterranean scrubland on limestone. Journal of Hydrology, 198 (1-4), 209-225. DOI: 10.1016/S0022-1694(96)03295-7 Cerdà, A. 1998. Changes in overland flow and infiltration after a rangeland fire in a Mediterranean scrubland, Hydrological Processes, 12 (7), 1031-1042. Cerdà, A. 1999. Seasonal and spatial variations in infiltration rates in badland surfaces under Mediterranean climatic conditions. Water Resources Research, 35 (1), 319-328. DOI: 10.1029/98WR01659 Cerdà, A. 2001.Effects of rock fragment cover on soil infiltration, interrill runoff and erosion. European Journal of Soil Science, 52 (1), 59-68. DOI: 10.1046/j.1365-2389.2001.00354.x Cerdà, A., Bodì, M.B. 2009. Infiltration process in the badlands of the East in the Iberian Peninsula. Progress and challenges. Cuadernos de Investigación Geográfica, 35 (1), 7-42. Keesstra, S.D. 2007. Impact of natural reforestation on floodplain sedimentation in the Dragonja basin, SW Slovenia. Earth Surface Processes and Landforms, 32(1): 49-65. DOI: 10.1002/esp.1360 Nanko, K., Giambelluca, T.W., Sutherland, R.A., Mudd, R.G., Nullet, M.A., Ziegler, A.D. 2015.Erosion potential under miconia calvescens stands on the island of hawai'i. Land Degradation and Development, 26 (3), pp. 218-226. DOI: 10.1002/ldr.2200 Pereira, P., Giménez-Morera, A., Novara, A., Keesstra, S., Jordán, A., Masto, R. E., Brevik, E., Azorin-Molina, C. Cerdà, A. 2015. The impact of road and railway embankments on runoff and soil erosion in eastern Spain. Hydrology and Earth System Sciences Discussions, 12, 12947-12985. Prosdocimi,M., Jordán, A., Tarolli, P., Keesstra, S., Novara, A., Cerdà, A. 2016. The immediate effectiveness of barley straw mulch in reducing soil erodibility and surface runoff generation in Mediterranean vineyards. Science of The Total Environment, 547, 15 ,323-330, doi:10.1016/j.scitotenv.2015.12.076 Wang Y., Fan J., Cao L., Liang Y. 2015. Infiltration and Runoff Generation Under Various Cropping Patterns in the Red Soil Region of China. Land Degradation and Development. DOI: 10. 1002/ldr. 2460 Zhao, C., Gao, J., Huang, Y., Wang, G., Zhang, M. 2015. Effects of Vegetation Stems on Hydraulics of Overland Flow Under Varying Water Discharges. Land Degradation and Development, DOI: 10.1002/ldr.2423

Results of infiltration tests near Scott City, western Kansas

USGS Publications Warehouse

Gillespie, Joe B.; Hargadine, G.D.

1976-01-01

Several types of ring infiltrometers were used to determine infiltration rates in loessial soil near Scott City, Kansas. Test results were evaluated for consistency, and were compared with infiltration rates in the underlying loess and with hydraulic conductivities in the unsaturated zone.Average daily infiltration rates in the Richfield soil ranged from 3 to 5 feet or 0.9 to 1.5 m (metres) after 16 days using 22-inch or 560mm (millimetre) ring infiltrometers; 2.3 feet (0.7 m) after 68 days using a 10-inch (250-mm) ring infiltrometer; and from 1.3 to 2.2 feet (0.4 to 0.7 m) after 38 days using double-ring infiltrometers. By comparison, the average daily infiltration rate in the underlying Peoria Loess using a 10-inch (250-mm) ring infiltrometer was about 13 feet (4.0 m) after 7 days.Tests using the double-ring infiltrometer, a paraffin seal in the 22-inch (560-mm) infiltrometer, and the measurement of flow through concentric areas of the soil core indicated that leakage of water between the infiltrometer wall and the soil was not significant. Lateral movement of the wetting front extended radially 4.7 feet (1.4 m) from the infiltrometer wall.Laboratory tests of a soil core indicated that the lowest hydraulic conductivity was in the depth interval from 3.9 to 8.6 inches (99 to 218 mm). Soil in this interval, which coincides with the depth of cultivation, evidently limits the rate of infiltration.Air-permeability tests in the unsaturated deposits gave a hydraulic conductivity of 0.2 foot per day (0.1 m/day) for the depth interval from 57 to 75 feet (17.0 to 23.0 m) as compared to a hydraulic conductivity of 1.9 feet per day (0.6 m/day) for the depth interval from 0 to 5 feet (0 to 1.5 m). A perched water table probably would occur above this interval during prolonged infiltration.Infiltration rates determined from the different types of ring infiltrometers were not consistent, but the tests showed that substantial quantities of water could infiltrate the Richfield soil.

Combined geophysical methods for mapping infiltration pathways at the Aurora Water Aquifer recharge and recovery site

NASA Astrophysics Data System (ADS)

Jasper, Cameron A.

Although aquifer recharge and recovery systems are a sustainable, decentralized, low cost, and low energy approach for the reclamation, treatment, and storage of post- treatment wastewater, they can suffer from poor infiltration rates and the development of a near-surface clogging layer within infiltration ponds. One such aquifer recharge and recovery system, the Aurora Water site in Colorado, U.S.A, functions at about 25% of its predicted capacity to recharge floodplain deposits by flooding infiltration ponds with post-treatment wastewater extracted from river bank aquifers along the South Platte River. The underwater self-potential method was developed to survey self-potential signals at the ground surface in a flooded infiltration pond for mapping infiltration pathways. A method for using heat as a groundwater tracer within the infiltration pond used an array of in situ high-resolution temperature sensing probes. Both relatively positive and negative underwater self-potential anomalies are consistent with observed recovery well pumping rates and specific discharge estimates from temperature data. Results from electrical resistivity tomography and electromagnetics surveys provide consistent electrical conductivity distributions associated with sediment textures. A lab method was developed for resistivity tests of near-surface sediment samples. Forward numerical modeling synthesizes the geophysical information to best match observed self- potential anomalies and provide permeability distributions, which is important for effective aquifer recharge and recovery system design, and optimization strategy development.

40 CFR 440.144 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... discharged from an open-cut mine plant site shall not exceed the volume of infiltration, drainage and mine... not exceed the volume of infiltration, drainage and mine drainage waters which is in excess of the...

40 CFR 440.144 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... discharged from an open-cut mine plant site shall not exceed the volume of infiltration, drainage and mine... not exceed the volume of infiltration, drainage and mine drainage waters which is in excess of the...

40 CFR 440.144 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... discharged from an open-cut mine plant site shall not exceed the volume of infiltration, drainage and mine... not exceed the volume of infiltration, drainage and mine drainage waters which is in excess of the...

Seawater infiltration effect on thermal degradation of fiber reinforced epoxy composites

NASA Astrophysics Data System (ADS)

Ibrahim, Mohd Haziq Izzuddin bin; Hassan, Mohamad Zaki bin; Ibrahim, Ikhwan; Rashidi, Ahmad Hadi Mohamed; Nor, Siti Fadzilah M.; Daud, Mohd Yusof Md

2018-05-01

Seawater salinity has been associated with the reduction of polymer structure durability. The aim of this study is to investigate the change in thermal degradation of fiber reinforced epoxy composite due to the presence of seawater. Carbon fiber, carbon/kevlar, fiberglass, and jute that reinforced with epoxy resin was laminated through hand-layup technique. Initially, these specimen was sectioned to 5×5 mm dimension, then immersed in seawater and distilled water at room temperature until it has thoroughly saturated. Following, the thermal degradation analysis using Differential Scanning Calorimetry (DSC), the thermic changes due to seawater infiltration was defined. The finding shows that moisture absorption reduces the glass transition temperature (Tg) of fiber reinforced epoxy composite. However, the glass transition temperature (Tg) of seawater infiltrated laminate composite is compareable with distilled water infiltrated laminate composite. The carbon fiber reinfored epoxy has the highest glass transition temperature out of all specimen.

Discrepancy between Snowmelt and Soil Infiltration

NASA Astrophysics Data System (ADS)

Fassnacht, S. R.

2017-12-01

A majority of snowmelt enters the soil and is either transmitted through or stored in the soil. Snowmelt has been estimated from the decrease in snow mass of a snow pillow and soil infiltration has been estimated from near surface TDR probes. Here, these data are from a set of Snow Telemetry (SNOTEL) stations across Colorado. While seasonal totals are similar, it is shown that there is a disconnect between the amount of water melted in a day and the increased daily volume of water measured in the near sub-surface. It is surmised that these differences are a function of the data collection methods, the infiltration rate, and possible lateral flow. An examination of daily infiltration volumes at depth shows a further disconnect, as it is likely that lateral flow complicates the measurements to a true three dimensional problem. The data are informative to illustrate the transmission of meltwater into the soil; methods for improvement are explored.

Review on airflow in unsaturated zones induced by natural forcings

NASA Astrophysics Data System (ADS)

Kuang, Xingxing; Jiao, Jiu Jimmy; Li, Hailong

2013-10-01

Subsurface airflow in unsaturated zones induced by natural forcings is of importance in many environmental and engineering fields, such as environmental remediation, water infiltration and groundwater recharge, coastal soil aeration, mine and tunnel ventilation, and gas exchange between soil and atmosphere. This review synthesizes the published literature on subsurface airflow driven by natural forcings such as atmospheric pressure fluctuations, topographic effect, water table fluctuations, and water infiltration. The present state of knowledge concerning the mechanisms, analytical and numerical models, and environmental and engineering applications related to the naturally occurring airflow is discussed. Airflow induced by atmospheric pressure fluctuations is studied the most because of the applications to environmental remediation and transport of trace gases from soil to atmosphere, which are very important in understanding biogeochemical cycling and global change. Airflow induced by infiltration is also an extensively investigated topic because of its implications in rainfall infiltration and groundwater recharge. Airflow induced by water table fluctuations is important in coastal areas because it plays an important role in coastal environmental remediation and ecological systems. Airflow induced by topographic effect is studied the least. However, it has important applications in unsaturated zone gas transport and natural ventilation of mines and tunnels. Finally, the similarities and differences in the characteristics of the air pressure and airflow are compared and future research efforts are recommended.

Soil water movement in the unsaturated zone of an inland arid region: Mulched drip irrigation experiment

NASA Astrophysics Data System (ADS)

Han, Dongmei; Zhou, Tiantian

2018-04-01

Agricultural irrigation with trans-basin water diversion can effectively relieve the water paucity in arid and semi-arid regions, however, this may be accompanied by eco-environmental problems (e.g., saline soils, rising groundwater levels, water quality problems). The mechanism of soil water movement under irrigation in the unsaturated zone of arid regions is a key scientific problem that should be solved in order to evaluate agricultural water management and further improve current irrigation practices. This study investigated the impact of drip irrigation on soil water movement in the unsaturated zone of a cotton field in an inland arid region (the Karamay Agricultural Development Area), northwest China. Combining in situ observational physical data with temporal variation in stable isotopic compositions of soil water, we described the soil water flow system and mechanism in severe (Plot 1) and mild (Plot 2) saline-alkali cotton fields. The infiltration depths are 0-150 cm for both plots. Drip irrigation scheduling makes no significant contribution to local groundwater recharge, however, groundwater can move into the unsaturated zone through capillary rise during cotton flowering and boll periods. Plot 2 is less prone to having secondary soil salinization than Plot 1 due to the existence of a middle layer (approximately 100 cm thick), which elongated the distance between the root zone and aquifer. Rise in the water table (approximately 60 cm for Plot 1 and 50 cm for Plot 2) could be caused by lateral groundwater flow instead of vertical infiltration. We estimated the soil water storage changes in the unsaturated zone and proposed a conceptual model for deciphering the movement process of soil water. This study provides a scientific basis for determining the rise of groundwater levels and potential development of saline soils and improving agricultural water management in arid regions.

Quantification of groundwater infiltration and surface water inflows in urban sewer networks based on a multiple model approach.

PubMed

Karpf, Christian; Krebs, Peter

2011-05-01

The management of sewer systems requires information about discharge and variability of typical wastewater sources in urban catchments. Especially the infiltration of groundwater and the inflow of surface water (I/I) are important for making decisions about the rehabilitation and operation of sewer networks. This paper presents a methodology to identify I/I and estimate its quantity. For each flow fraction in sewer networks, an individual model approach is formulated whose parameters are optimised by the method of least squares. This method was applied to estimate the contributions to the wastewater flow in the sewer system of the City of Dresden (Germany), where data availability is good. Absolute flows of I/I and their temporal variations are estimated. Further information on the characteristics of infiltration is gained by clustering and grouping sewer pipes according to the attributes construction year and groundwater influence and relating these resulting classes to infiltration behaviour. Further, it is shown that condition classes based on CCTV-data can be used to estimate the infiltration potential of sewer pipes. Copyright © 2011 Elsevier Ltd. All rights reserved.

The infiltration-centrifugation technique for extraction of apoplastic fluid from plant leaves using Phaseolus vulgaris as an example.

PubMed

O'Leary, Brendan M; Rico, Arantza; McCraw, Sarah; Fones, Helen N; Preston, Gail M

2014-12-19

The apoplast is a distinct extracellular compartment in plant tissues that lies outside the plasma membrane and includes the cell wall. The apoplastic compartment of plant leaves is the site of several important biological processes, including cell wall formation, cellular nutrient and water uptake and export, plant-endophyte interactions and defence responses to pathogens. The infiltration-centrifugation method is well established as a robust technique for the analysis of the soluble apoplast composition of various plant species. The fluid obtained by this method is commonly known as apoplast washing fluid (AWF). The following protocol describes an optimized vacuum infiltration and centrifugation method for AWF extraction from Phaseolus vulgaris (French bean) cv. Tendergreen leaves. The limitations of this method and the optimization of the protocol for other plant species are discussed. Recovered AWF can be used in a wide range of downstream experiments that seek to characterize the composition of the apoplast and how it varies in response to plant species and genotype, plant development and environmental conditions, or to determine how microorganisms grow in apoplast fluid and respond to changes in its composition.

The Infiltration-centrifugation Technique for Extraction of Apoplastic Fluid from Plant Leaves Using Phaseolus vulgaris as an Example

PubMed Central

O'Leary, Brendan M.; Rico, Arantza; McCraw, Sarah; Fones, Helen N.; Preston, Gail M.

2014-01-01

The apoplast is a distinct extracellular compartment in plant tissues that lies outside the plasma membrane and includes the cell wall. The apoplastic compartment of plant leaves is the site of several important biological processes, including cell wall formation, cellular nutrient and water uptake and export, plant-endophyte interactions and defence responses to pathogens. The infiltration-centrifugation method is well established as a robust technique for the analysis of the soluble apoplast composition of various plant species. The fluid obtained by this method is commonly known as apoplast washing fluid (AWF). The following protocol describes an optimized vacuum infiltration and centrifugation method for AWF extraction from Phaseolus vulgaris (French bean) cv. Tendergreen leaves. The limitations of this method and the optimization of the protocol for other plant species are discussed. Recovered AWF can be used in a wide range of downstream experiments that seek to characterize the composition of the apoplast and how it varies in response to plant species and genotype, plant development and environmental conditions, or to determine how microorganisms grow in apoplast fluid and respond to changes in its composition. PMID:25549068

Water movement through a thick unsaturated zone underlying an intermittent stream in the western Mojave Desert, southern California, USA

USGS Publications Warehouse

Izbicki, J.A.; Radyk, J.; Michel, R.L.

2000-01-01

Previous studies indicated that small amounts of recharge occur as infiltration of intermittent streamflow in washes in the upper Mojave River basin, in the western Mojave Desert, near Victorville, California. These washes flow only a few days each year after large storms. To reach the water table, water must pass through an unsaturated zone that is more than 130 m thick. Results of this study, done in 1994-1998, showy that infiltration to depths below the root zone did not occur at control sites away from the wash. At these sites, volumetric water contents were as low as 0.01 and water potentials (measured as the combination of solute and matric potentials using a water activity meter) were as negative as -14,000 kPa. Water-vapor movement was controlled by highly negative solute potentials associated with the accumulation of soluble salts in the unsaturated zone. Highly negative matric potentials above and below the zone of maximum solute accumulation result from movement of water vapor toward the highly negative solute potentials at that depth. The ??18O and ??D (delta oxygen-18 and delta deuterium) isotopic composition of water in coarse-grained deposits plots along a Rayleigh distillation line consistent with removal of water in coarse-grained layers by vapor transport. Beneath Oro Grande Wash, water moved to depths below the root zone and, presumably, to the water table about 130 m below land surface. Underneath Oro Grande Wash, volumetric water contents were as high as 0.27 and water potentials (measured as matric potential using tensiometers) were between -1.8 and -50 kPa. On the basis of tritium data, water requires at least 180-260 years to infiltrate to the water table. Clay layers impede the downward movement of water. Seasonal changes in water vapor composition underneath the wash are consistent with the rapid infiltration of a small quantity of water to great depths and subsequent equilibration of vapor with water in the surrounding material. It may be possible to supplement natural recharge from the wash with imported water. Recharge to the wash may be advantageous because the unsaturated zone is not as dry as most areas in the desert and concentrations of soluble salts are generally lower underneath the wash.Previous studies indicated that small amounts of recharge occur as infiltration of intermittent streamflow in washes in the upper Mojave River basin, in the western Mojave Desert, near Victorville, California. These washes flow only a few days each year after large storms. To reach the water table, water must pass through an unsaturated zone that is more than 130 m thick. Results of this study, done in 1994-1998, show that infiltration to depths below the root zone did not occur at control sites away from the wash. At these sites, volumetric water contents were as low as 0.01 and water potentials (measured as the combination of solute and matric potentials using a water activity meter) were as negative as -14,000 kPa. Water-vapor movement was controlled by highly negative solute potentials associated with the accumulation of soluble salts in the unsaturated zone. Highly negative matric potentials above and below the zone of maximum solute accumulation result from movement of water vapor toward the highly negative solute potentials at that depth. The ??18O and ??D (delta oxygen-18 and delta deuterium) isotopic composition of water in coarse-grained deposits plots along a Rayleigh distillation line consistent with removal of water in coarse-grained layers by vapor transport. Beneath Oro Grande Wash, water moved to depths below the root zone and, presumably, to the water table about 130 m below land surface. Underneath Oro Grande Wash, volumetric water contents were as high as 0.27 and water potentials (measured as matric potential using tensiometers) were between -1.8 and -50 kPa. On the basis of tritium data, water requires at least 180-260 years to infiltrate to the water table. Clay layers impede the downwa

Estimating macroporosity in a forest watershed by use of a tension infiltrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watson, K.W.; Luxmoore, R.J.

The ability to obtain sufficient field hydrologic data at reasonable cost can be an important limiting factor in applying transport models. A procedure is described for using ponded-flow- and tension-infiltration measurements to calculate transport parameters in a forest watershed. Thirty infiltration measurements were taken under ponded-flow conditions and at 3, 6, and 15 cm (H/sub 2/O) tension. It was assumed from capillarity theory that pores > 0.1-, 0.05-, and 0.02-cm diam, respectively, were excluded from the transport process during the tension infiltration measurements. Under ponded flow, 73% of the flux was conducted through macropores (i.e., pores > 0.1-cm diam.). Anmore » estimated 96% of the water flux was transmitted through only 0.32% of the soil volume. In general the larger the total water flux the larger the macropore contribution to total water flux. The Shapiro-Wilk normality test indicated that water flux through both matrix pore space and macropores was log-normally distributed in space.« less

Microorganism Removal in Permeable Pavement Parking Lots ...

EPA Pesticide Factsheets

Three types of permeable pavements (pervious concrete, permeable interlocking concrete pavers, and porous asphalt) were monitored at the Edison Environmental Center in Edison, New Jersey for indicator organisms such as fecal coliform, enterococci, and E. coli. Results showed that porous asphalt had much lower concentration in monitored infiltrate compared to pervious concrete and permeable interlocking concrete pavers. Concentrations of monitored organisms in infiltrate from porous asphalt were consistently below the bathing water quality standard. Fecal coliform and enterococci exceeded bathing water quality standards more than 72% and 34% of the time for permeable interlocking concrete pavers and pervious concrete, respectively. Purpose is to evaluate the performance of permeable pavement in removing indicator organisms from infiltrating stormwater runoff.

An Investigation of Fat Infiltration of the Multifidus Muscle in Patients With Severe Neck Symptoms Associated With Chronic Whiplash-Associated Disorder.

PubMed

Karlsson, Anette; Leinhard, Olof Dahlqvist; Åslund, Ulrika; West, Janne; Romu, Thobias; Smedby, Örjan; Zsigmond, Peter; Peolsson, Anneli

2016-10-01

Study Design Cross-sectional study. Background Findings of fat infiltration in cervical spine multifidus, as a sign of degenerative morphometric changes due to whiplash injury, need to be verified. Objectives To develop a method using water/fat magnetic resonance imaging (MRI) to investigate fat infiltration and cross-sectional area of multifidus muscle in individuals with whiplash-associated disorders (WADs) compared to healthy controls. Methods Fat infiltration and cross-sectional area in the multifidus muscles spanning the C4 to C7 segmental levels were investigated by manual segmentation using water/fat-separated MRI in 31 participants with WAD and 31 controls, matched for age and sex. Results Based on average values for data spanning C4 to C7, participants with severe disability related to WAD had 38% greater muscular fat infiltration compared to healthy controls (P = .03) and 45% greater fat infiltration compared to those with mild to moderate disability related to WAD (P = .02). There were no significant differences between those with mild to moderate disability and healthy controls. No significant differences between groups were found for multifidus cross-sectional area. Significant differences were observed for both cross-sectional area and fat infiltration between segmental levels. Conclusion Participants with severe disability after a whiplash injury had higher fat infiltration in the multifidus compared to controls and to those with mild/moderate disability secondary to WAD. Earlier reported findings using T1-weighted MRI were reproduced using refined imaging technology. The results of the study also indicate a risk when segmenting single cross-sectional slices, as both cross-sectional area and fat infiltration differ between cervical levels. J Orthop Sports Phys Ther 2016;46(10):886-893. Epub 2 Sep 2016. doi:10.2519/jospt.2016.6553.

Soil Infiltration Characteristics in Agroforestry Systems and Their Relationships with the Temporal Distribution of Rainfall on the Loess Plateau in China

PubMed Central

Wang, Lai; Zhong, Chonggao; Gao, Pengxiang; Xi, Weimin; Zhang, Shuoxin

2015-01-01

Many previous studies have shown that land use patterns are the main factors influencing soil infiltration. Thus, increasing soil infiltration and reducing runoff are crucial for soil and water conservation, especially in semi-arid environments. To explore the effects of agroforestry systems on soil infiltration and associated properties in a semi-arid area of the Loess Plateau in China, we compared three plant systems: a walnut (Juglans regia) monoculture system (JRMS), a wheat (Triticum aestivum) monoculture system (TAMS), and a walnut-wheat alley cropping system (JTACS) over a period of 11 years. Our results showed that the JTACS facilitated infiltration, and its infiltration rate temporal distribution showed a stronger relationship coupled with the rainfall temporal distribution compared with the two monoculture systems during the growing season. However, the effect of JTACS on the infiltration capacity was only significant in shallow soil layer, i.e., the 0–40 cm soil depth. Within JTACS, the speed of the wetting front’s downward movement was significantly faster than that in the two monoculture systems when the amount of rainfall and its intensity were higher. The soil infiltration rate was improved, and the two peaks of soil infiltration rate temporal distribution and the rainfall temporal distribution coupled in rainy season in the alley cropping system, which has an important significance in soil and water conservation. The results of this empirical study provide new insights into the sustainability of agroforestry, which may help farmers select rational planting patterns in this region, as well as other regions with similar climatic and environmental characteristics throughout the world. PMID:25893832

Soil Infiltration Characteristics in Agroforestry Systems and Their Relationships with the Temporal Distribution of Rainfall on the Loess Plateau in China.

PubMed

Wang, Lai; Zhong, Chonggao; Gao, Pengxiang; Xi, Weimin; Zhang, Shuoxin

2015-01-01

Many previous studies have shown that land use patterns are the main factors influencing soil infiltration. Thus, increasing soil infiltration and reducing runoff are crucial for soil and water conservation, especially in semi-arid environments. To explore the effects of agroforestry systems on soil infiltration and associated properties in a semi-arid area of the Loess Plateau in China, we compared three plant systems: a walnut (Juglans regia) monoculture system (JRMS), a wheat (Triticum aestivum) monoculture system (TAMS), and a walnut-wheat alley cropping system (JTACS) over a period of 11 years. Our results showed that the JTACS facilitated infiltration, and its infiltration rate temporal distribution showed a stronger relationship coupled with the rainfall temporal distribution compared with the two monoculture systems during the growing season. However, the effect of JTACS on the infiltration capacity was only significant in shallow soil layer, i.e., the 0-40 cm soil depth. Within JTACS, the speed of the wetting front's downward movement was significantly faster than that in the two monoculture systems when the amount of rainfall and its intensity were higher. The soil infiltration rate was improved, and the two peaks of soil infiltration rate temporal distribution and the rainfall temporal distribution coupled in rainy season in the alley cropping system, which has an important significance in soil and water conservation. The results of this empirical study provide new insights into the sustainability of agroforestry, which may help farmers select rational planting patterns in this region, as well as other regions with similar climatic and environmental characteristics throughout the world.

Simulation of ground-water flow in the Cedar River alluvial aquifer flow system, Cedar Rapids, Iowa

USGS Publications Warehouse

Turco, Michael J.; Buchmiller, Robert C.

2004-01-01

Model results indicate that the primary sources of inflow to the modeled area are infiltration from the Cedar River (53.0 percent) and regional flow in the glacial and bedrock materials (34.1 percent). The primary sources of outflow from the modeled area are discharge to the Cedar River (45.4 percent) and pumpage (44.8 percent). Current steady-state pumping rates have increased the flow of water from the Cedar River to the alluvial aquifer by 43.8 cubic feet per second. Steady-state and transient hypothetical pumpage scenarios were used to show the relation between changes in pumpage and changes in infiltration of water from the Cedar River. Results indicate that more than 99 percent of the water discharging from municipal wells infiltrates from the Cedar River, that the time required for induced river recharge to equilibrate with municipal pumpage may be 150 days or more, and that ground-water availability in the Cedar Rapids area will not be significantly affected by doubling current pumpage as long as there is sufficient flow in the Cedar River to provide recharge.

30 CFR 785.19 - Surface coal mining and reclamation operations on areas or adjacent to areas including alluvial...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., rate and frequency of rainfall and runoff, surface roughness, slope and vegetative cover, infiltration... the function of storing water, such as permeability, infiltration, porosity, depth and direction of...

30 CFR 785.19 - Surface coal mining and reclamation operations on areas or adjacent to areas including alluvial...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., rate and frequency of rainfall and runoff, surface roughness, slope and vegetative cover, infiltration... the function of storing water, such as permeability, infiltration, porosity, depth and direction of...

30 CFR 785.19 - Surface coal mining and reclamation operations on areas or adjacent to areas including alluvial...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., rate and frequency of rainfall and runoff, surface roughness, slope and vegetative cover, infiltration... the function of storing water, such as permeability, infiltration, porosity, depth and direction of...

30 CFR 785.19 - Surface coal mining and reclamation operations on areas or adjacent to areas including alluvial...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., rate and frequency of rainfall and runoff, surface roughness, slope and vegetative cover, infiltration... the function of storing water, such as permeability, infiltration, porosity, depth and direction of...

30 CFR 785.19 - Surface coal mining and reclamation operations on areas or adjacent to areas including alluvial...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., rate and frequency of rainfall and runoff, surface roughness, slope and vegetative cover, infiltration... the function of storing water, such as permeability, infiltration, porosity, depth and direction of...

Response of rock-fissure seepage to snowmelt in Mount Taihang slope-catchment, North China.

PubMed

Cao, Jiansheng; Liu, Changming; Zhang, Wanjun

2013-01-01

The complex physiographic and hydrogeological systems of mountain terrains facilitate intense rock-fissure seepages and multi-functional ecological interactions. As mountain eco-hydrological terrains are the common water sources of river basins across the globe, it is critical to build sufficient understanding into the hydrological processes in this unique ecosystem. This study analyzes infiltration and soil/rock-fissure seepage processes from a 65 mm snowfall/melt in November 2009 in the typical granitic gneiss slope catchment in the Taihang Mountains. The snowfall, snowmelt and melt-water processes are monitored using soil-water time-domain reflectometry (TDR) probes and tipping bucket flowmeters. The results suggest that snowmelt infiltration significantly influences soil/rock water seepage in the 0-100 cm soil depth of the slope-catchment. It is not only air temperature that influences snowmelt, but also snowmelt infiltration and rock-fissure seepage. Diurnal variations in rock-fissure seepage are in close correlation with air temperature (R(2) > 0.7). Temperature also varies with soil/rock water viscosity, which element in turn influences soil/rock water flow. Invariably, water dynamics in the study area is not only a critical water supply element for domestic, industrial and agricultural uses, but also for food security and social stability.

Ground-water recharge from small intermittent streams in the western Mojave Desert, California: Chapter G in Ground-water recharge in the arid and semiarid southwestern United States (Professional Paper 1703)

USGS Publications Warehouse

Izbicki, John A.; Johnson, Russell U.; Kulongoski, Justin T.; Predmore, Steven; Stonestrom, David A.; Constantz, Jim; Ferré, Ty P.A.; Leake, Stanley A.

2007-01-01

Population growth has impacted ground-water resources in the western Mojave Desert, where declining water levels suggest that recharge rates have not kept pace with withdrawals. Recharge from the Mojave River, the largest hydrographic feature in the study area, is relatively well characterized. In contrast, recharge from numerous smaller streams that convey runoff from the bounding mountains is poorly characterized. The current study examined four representative streams to assess recharge from these intermittent sources. Hydraulic, thermal, geomorphic, chemical, and isotopic data were used to study recharge processes, from streamflow generation and infiltration to percolation through the unsaturated zone. Ground-water movement away from recharge areas was also assessed.Infiltration in amounts sufficient to have a measurable effect on subsurface temperature profiles did not occur in every year in instrumented study reaches. In addition to streamflow availability, results showed the importance of sediment texture in controlling infiltration and eventual recharge. Infiltration amounts of about 0.7 meters per year were an approximate threshold for the occurrence of ground-water recharge. Estimated travel times through the thick unsaturated zones underlying channels reached several hundred years. Recharging fluxes were influenced by stratigraphic complexity and depositional dynamics. Because of channel meandering, not all water that penetrates beneath the root zone can be assumed to become recharge on active alluvial fans.Away from study washes, elevated chloride concentrations and highly negative water potentials beneath the root zone indicated negligible recharge from direct infiltration of precipitation under current climatic conditions. In upstream portions of washes, generally low subsurface chloride concentrations and near-zero water potentials indicated downward movement of water toward the water table, driven primarily by gravity. Recharging conditions did not extend to the distal ends of all washes. Where urbanization had concentrated spatially distributed runoff into a small number of fixed channels, enhanced infiltration induced recharging conditions, mobilizing accumulated chloride.Estimated amounts of ground-water recharge from the studied reaches were small. Extrapolating on the basis of drainage areas, the estimated aggregate recharge from small intermittent streams is minor compared to recharge from the Mojave River. Recharge is largely controlled by streamflow availability, which primarily reflects precipitation patterns. Precipitation in the Mojave Desert is strongly controlled by topography. Cool moist air masses from the Pacific Ocean are mostly blocked from entering the desert by the high mountains bordering its southern edge. Storms do, however, readily enter the region through Cajon Pass. These storms generate flow in the Mojave River that often reaches Afton Canyon, more than 150 kilometers downstream. The isotopic composition of ground water reflects the localization of recharge beneath the Mojave River. Similar processes occur near San Gorgonio Pass, 75 kilometers southeast from Cajon Pass along the bounding San Andreas Fault.

Hydrogeologic conditions in the town of Shelter Island, Suffolk County, Long Island, New York

USGS Publications Warehouse

Soren, Julian

1978-01-01

Shelter Island, an area of about 11 square miles, in Suffolk County, N.Y., is situated between the north and south forks of eastern Long Island. The upper glacial aquifer is the sole source of freshwater supply for Shelter Island 's population, which currently ranges seasonally from 2,000 to 8,000. Fresh ground water seems to be limited to sand and gravel deposits in the aquifer, which is thin and can be readily infiltrated by surrounding saline ground water. The aquifer is underlain by confining clay formations that contain saline water, and the geologic formations below the clay probably contain saline water also. The fresh ground water is mostly soft and has low dissolved-solids concentrations; however, several wells near shorelines have yielded excessive amounts of chloride. Man-induced contamination of the aquifer is evident but not severe, as shown by somewhat elevated concentrations of nitrate nitrogen and methylene blue active substances (MBAS). Increased pumping will cause deterioration of the fresh ground-water supply by inducing saline-water infiltration and by adding greater volumes of septic-tank and cesspool effluents to the aquifer. Test drilling could help in water-supply management by determining the extent of the aquifer and of fresh ground-water storage, and observation wells could provide early detection of saline-water infiltration. (Woodard-USGS)

Electrodialysis and nanofiltration of surface water for subsequent use as infiltration water.

PubMed

Van der Bruggen, B; Milis, R; Vandecasteele, C; Bielen, P; Van San, E; Huysman, K

2003-09-01

In order to achieve stable groundwater levels, an equilibrium between the use of groundwater for drinking water production and natural or artificial groundwater recharge by infiltration is needed. Local governments usually require that the composition of the water used for artificial recharge is similar to the surface water that is naturally present in the specific recharge area. In this paper, electrodialysis (ED) and nanofiltration were evaluated as possible treatment technologies for surface water from a canal in Flanders, the North of Belgium, in view of infiltration at critical places on heathlands. Both methods were evaluated on the basis of a comparison between the water composition after treatment and the composition of local surface waters. The treatment generally consists of a tuning of pH and the removal of contaminants originating from industrial and agricultural activity, e.g., nitrates and pesticides. Further evaluation of the influence of the composition of the water on the characteristics of the artificial recharge, however, was not envisaged. In a case study of water from the canal Schoten-Dessel, satisfactory concentration reductions of Cl(-), SO(4)(2-), NO(3)(-), HCO(3)(-), Na(+), Mg(2+), K(+) and Ca(2+) were obtained by ultrafiltration pretreatment followed by ED. Nanofiltration with UTC-20, N30F, Desal 51 HL, UTC-60 and Desal 5 DL membranes resulted in an insufficient removal level, especially for the monovalent ions.

From Rain Tanks to Catchments: Use of Low-Impact Development To Address Hydrologic Symptoms of the Urban Stream Syndrome.

PubMed

Askarizadeh, Asal; Rippy, Megan A; Fletcher, Tim D; Feldman, David L; Peng, Jian; Bowler, Peter; Mehring, Andrew S; Winfrey, Brandon K; Vrugt, Jasper A; AghaKouchak, Amir; Jiang, Sunny C; Sanders, Brett F; Levin, Lisa A; Taylor, Scott; Grant, Stanley B

2015-10-06

Catchment urbanization perturbs the water and sediment budgets of streams, degrades stream health and function, and causes a constellation of flow, water quality, and ecological symptoms collectively known as the urban stream syndrome. Low-impact development (LID) technologies address the hydrologic symptoms of the urban stream syndrome by mimicking natural flow paths and restoring a natural water balance. Over annual time scales, the volumes of stormwater that should be infiltrated and harvested can be estimated from a catchment-scale water-balance given local climate conditions and preurban land cover. For all but the wettest regions of the world, a much larger volume of stormwater runoff should be harvested than infiltrated to maintain stream hydrology in a preurban state. Efforts to prevent or reverse hydrologic symptoms associated with the urban stream syndrome will therefore require: (1) selecting the right mix of LID technologies that provide regionally tailored ratios of stormwater harvesting and infiltration; (2) integrating these LID technologies into next-generation drainage systems; (3) maximizing potential cobenefits including water supply augmentation, flood protection, improved water quality, and urban amenities; and (4) long-term hydrologic monitoring to evaluate the efficacy of LID interventions.

Sources of oxygen flux in groundwater during induced bank filtration at a site in Berlin, Germany

NASA Astrophysics Data System (ADS)

Kohfahl, Claus; Massmann, Gudrun; Pekdeger, Asaf

2009-05-01

The microbial degradation of pharmaceuticals found in surface water used for artificial recharge is strongly dependent on redox conditions of the subsurface. Furthermore the durability of production wells may decrease considerably with the presence of oxygen and ferrous iron due to the precipitation of trivalent iron oxides and subsequent clogging. Field measurements are presented for oxygen at a bank filtration site in Berlin, Germany, along with simplified calculations of different oxygen pathways into the groundwater. For a two-dimensional vertical cross-section, oxygen input has been calculated for six scenarios related to different water management strategies. Calculations were carried out in order to assess the amount of oxygen input due to (1) the infiltration of oxic lake water, (2) air entrapment as a result of water table oscillations, (3) diffusive oxygen flux from soil air and (4) infiltrating rainwater. The results show that air entrapment and infiltrating lake water during winter constitute by far the most important mechanism of oxygen input. Oxygen input by percolating rainwater and by diffusive delivery of oxygen in the gas phase is negligible. The results exemplify the importance of well management as a determining factor for water oscillations and redox conditions during artificial recharge.

Advanced Standoff Interdiction Weapon and Sensor System. Volume 1

DTIC Science & Technology

1972-06-15

interdiction system to counter enemy infiltration along the water - ways and roads of Southeast Asia. The sensors were selected to give the helicopter a...was con- ceived as an interdiction system to counter enemy infiltration along the water - ways ard roads of Southeast Asia. The sensors were selected...controller enabled him to fly the helicopter to intercept the moving target. Mount camera film was exposed while the target was being fracked by the

18 CFR 401.35 - Classification of projects for review under Section 3.8 of the Compact.

Code of Federal Regulations, 2010 CFR

2010-04-01

... materials; (6) A change in land cover on major ground water infiltration areas when the amount of land that... infiltration areas; (11) Hydroelectric power projects, including pumped storage projects; (12) Projects or...

18 CFR 401.35 - Classification of projects for review under Section 3.8 of the Compact.

Code of Federal Regulations, 2013 CFR

2013-04-01

... materials; (6) A change in land cover on major ground water infiltration areas when the amount of land that... infiltration areas; (11) Hydroelectric power projects, including pumped storage projects; (12) Projects or...

18 CFR 401.35 - Classification of projects for review under Section 3.8 of the Compact.

Code of Federal Regulations, 2014 CFR

2014-04-01

... materials; (6) A change in land cover on major ground water infiltration areas when the amount of land that... infiltration areas; (11) Hydroelectric power projects, including pumped storage projects; (12) Projects or...

18 CFR 401.35 - Classification of projects for review under Section 3.8 of the Compact.

Code of Federal Regulations, 2012 CFR

2012-04-01

... materials; (6) A change in land cover on major ground water infiltration areas when the amount of land that... infiltration areas; (11) Hydroelectric power projects, including pumped storage projects; (12) Projects or...

40 CFR 35.927-2 - Sewer system evaluation survey.

Code of Federal Regulations, 2014 CFR

2014-07-01

... FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act... transportation and treatment for each defined source of infiltration/inflow. (b) A report shall summarize the... sewer system to eliminate all defined excessive infiltration/inflow. ...

Effects of gravel on infiltration, runoff, and sediment yield in landslide deposit slope in Wenchuan earthquake area, China.

PubMed

Li, Tianyang; He, Binghui; Chen, Zhanpeng; Zhang, Yi; Liang, Chuan; Wang, Renxin

2016-06-01

Amounts of landslide deposits were triggered by the Wenchuan earthquake with magnitude 8.0 on May 12, 2008. The landslide deposits were composed of soil and rock fragments, which play important roles in hydrological and erosion processes in the steep slope of landslide deposits. The mixtures of soil and gravels are common in the top layers of landslide deposits, and its processes are obviously different with the soil without gravels. Based on the data of field investigation, a series of simulated scouring flow experiments with four proportion of gravel (0, 25, 33.3, and 50 %) and three scouring flow rates (4, 8, 12 L/min) under two steep slopes (67.5, 72.7 %) were conducted sequentially to know the effects of proportion of gravel on infiltration capacity, runoff generation, and sediment production in the steep slope of landslide deposit. Results indicated that gravel had promoted or reduced effects on infiltration capacity which could affect further the cumulative runoff volume and cumulative sediment mass increase or decrease. The cumulative infiltration volume in 25 % proportion of gravel was less than those in 0, 33.3, and 50 % proportion of gravel. The cumulative runoff volume was in an order of 25 > 0 > 33.3 > 50 % while cumulative sediment mass ranked as 25 > 33.3 > 0 > 50 % with different proportions of gravel. A significant power relationship was found between scouring time and cumulative runoff volume as well as cumulative sediment mass. The relationship between average soil and water loss rate and proportion of gravel was able to express by quadratic function, with a high degree of reliability. The results have important implications for soil and water conservation and modeling in landslide deposit but also provide useful information for the similar conditions.

Modeling snowmelt infiltration in seasonally frozen ground

NASA Astrophysics Data System (ADS)

Budhathoki, S.; Ireson, A. M.

2017-12-01

In cold regions, freezing and thawing of the soil govern soil hydraulic properties that shape the surface and subsurface hydrological processes. The partitioning of snowmelt into infiltration and runoff has also important implications for integrated water resource management and flood risk. However, there is an inadequate representation of the snowmelt infiltration into frozen soils in most land-surface and hydrological models, creating the need for improved models and methods. Here we apply, the Frozen Soil Infiltration Model, FroSIn, which is a novel algorithm for infiltration in frozen soils that can be implemented in physically based models of coupled flow and heat transport. In this study, we apply the model in a simple configuration to reproduce observations from field sites in the Canadian prairies, specifically St Denis and Brightwater Creek in Saskatchewan, Canada. We demonstrate the limitations of conventional approaches to simulate infiltration, which systematically over-predict runoff and under predict infiltration. The findings show that FroSIn enables models to predict more reasonable infiltration volumes in frozen soils, and also represent how infiltration-runoff partitioning is impacted by antecedent soil moisture.

Infiltration into soils: Conceptual approaches and solutions

NASA Astrophysics Data System (ADS)

Assouline, Shmuel

2013-04-01

Infiltration is a key process in aspects of hydrology, agricultural and civil engineering, irrigation design, and soil and water conservation. It is complex, depending on soil and rainfall properties and initial and boundary conditions within the flow domain. During the last century, a great deal of effort has been invested to understand the physics of infiltration and to develop quantitative predictors of infiltration dynamics. Jean-Yves Parlange and Wilfried Brutsaert have made seminal contributions, especially in the area of infiltration theory and related analytical solutions to the flow equations. This review retraces the landmark discoveries and the evolution of the conceptual approaches and the mathematical solutions applied to the problem of infiltration into porous media, highlighting the pivotal contributions of Parlange and Brutsaert. A historical retrospective of physical models of infiltration is followed by the presentation of mathematical methods leading to analytical solutions of the flow equations. This review then addresses the time compression approximation developed to estimate infiltration at the transition between preponding and postponding conditions. Finally, the effects of special conditions, such as the presence of air and heterogeneity in soil properties, on infiltration are considered.

Residence times and mixing of water in river banks: implications for recharge and groundwater-surface water exchange

NASA Astrophysics Data System (ADS)

Unland, N. P.; Cartwright, I.; Cendón, D. I.; Chisari, R.

2014-12-01

Bank exchange processes within 50 m of the Tambo River, southeast Australia, have been investigated through the combined use of 3H and 14C. Groundwater residence times increase towards the Tambo River, which suggests the absence of significant bank storage. Major ion concentrations and δ2H and δ18O values of bank water also indicate that bank infiltration does not significantly impact groundwater chemistry under baseflow and post-flood conditions, suggesting that the gaining nature of the river may be driving the return of bank storage water back into the Tambo River within days of peak flood conditions. The covariance between 3H and 14C indicates the leakage and mixing between old (~17 200 years) groundwater from a semi-confined aquifer and younger groundwater (<100 years) near the river, where confining layers are less prevalent. It is likely that the upward infiltration of deeper groundwater from the semi-confined aquifer during flooding limits bank infiltration. Furthermore, the more saline deeper groundwater likely controls the geochemistry of water in the river bank, minimising the chemical impact that bank infiltration has in this setting. These processes, coupled with the strongly gaining nature of the Tambo River are likely to be the factors reducing the chemical impact of bank storage in this setting. This study illustrates the complex nature of river groundwater interactions and the potential downfall in assuming simple or idealised conditions when conducting hydrogeological studies.

[Characteristics of soil moisture in artificial impermeable layers].

PubMed

Suo, Gai-Di; Xie, Yong-Sheng; Tian, Fei; Chuai, Jun-Feng; Jing, Min-Xiao

2014-09-01

For the problem of low water and fertilizer use efficiency caused by nitrate nitrogen lea- ching into deep soil layer and soil desiccation in dryland apple orchard, characteristics of soil moisture were investigated by means of hand tamping in order to find a new approach in improving the water and fertilizer use efficiency in the apple orchard. Two artificial impermeable layers of red clay and dark loessial soil were built in soil, with a thickness of 3 or 5 cm. Results showed that artificial impermeable layers with the two different thicknesses were effective in reducing or blocking water infiltration into soil and had higher seepage controlling efficiency. Seepage controlling efficiency for the red clay impermeable layer was better than that for the dark loessial soil impermeable layer. Among all the treatments, the red clay impermeable layer of 5 cm thickness had the highest bulk density, the lowest initial infiltration rate (0.033 mm · min(-1)) and stable infiltration rate (0.018 mm · min(-1)) among all treatments. After dry-wet alternation in summer and freezing-thawing cycle in winter, its physiochemical properties changed little. Increase in years did not affect stable infiltration rate of soil water. The red clay impermeable layer of 5 cm thickness could effectively increase soil moisture content in upper soil layer which was conducive to raise the water and nutrient use efficiency. The approach could be applied to the apple production of dryland orchard.

Mimicking pestcide percolation dynamics in ditches bed by successive column infltration experiment

NASA Astrophysics Data System (ADS)

Dages, Cecile; Samouelian, Anatja; Storck, Veronika; Negro, Sandrine; Huttel, Olivier; Voltz, Marc

2014-05-01

Soil layers underlying ditch beds acquire specific characteristics due to ii) hydrological and erosion/deposition processes occurring within the ditch and ii) management practices (burning, dredging, mowing, …). For example, organic matter contents of the ditch beds can be larger than those in neighboring fields, since ditches act as buffer zones. Besides, in Mediterranean catchments, farmed ditches are known to be zones of groundwater recharge and thereby may contribute to groundwater pollution. The role of farmed ditches in groundwater contamination needs therefore to be clarified. The purpose of this study was to determine the dynamic of pesticide percolation in infiltrating farmed ditches bed during a sequence of flood events. A complementary aim was to determine to which extent pesticide percolation from the ditches is correlated to surface flow water contamination. A succession of 9 flood simulations were performed on an undisturbed soil column sampled in the a ditch of the Roujan catchment (Hérault, France), which belongs to the long term Mediterranean hydrological observatory OMERE (Voltz and Albergel, 2002). The soil column was 15 cm long with a 15 cm inner-diameter. For the first 5 flood simulations, injected water was doped with 14C-diuron, an herbicide used in vineyards; uncontaminated water was injected for the last 4 simulations. Free drainage was imposed at the bottom of the column. Diuron concentration was kept constant during a simulated infiltration experiment, but it was progressively decreased from 1000 to 0 µg/L along the succession of the 9 events to mimic the observed seasonal variation of mean diuron concentration in surface flow at the study site (Louchart et al., 2001). Additionally, the first flood simulation was performed with tritium water to assess references on conservative transport within the soil column. For each simulation, the inflow and outflow hydrogram and chemogram were monitored. Extractable (water and solvent) and non-extractable (NER) diuron residues in the soil column were determined at the end of the simulation. The results show two main points. First, a very significant part of the infiltrated pesticide and its metabolites leached or could have leached, with a dynamic that is not directly linked with surface water concentrations. Indeed, from the third flood, diuron leaching concentrations were higher than injected diuron concentration. Moreover, the chemogram of diuron leaching was very similar for the 2 last flood simulations (with clear water) with diuron concentrations remaining quite high (from 8 to 2 µg/L). Second, water flow and diuron transport mechanisms involve two ways: a fast way attributed to macroporal flow and a slow one that corresponds to microporal flow. The macroporal compartment varied during and along flood simulations inducing different proportion of water and diuron fast flowing. Finally the possibility that farmed ditches contribute to groundwater contamination is high. Contamination mechanisms seem to be complex with a fast way leading to direct contamination of underlying soil layer with actual flooding water and a delayed way leading with past flooding water and involving the remobilization of pollutants stocked within the soil.

Rainfall-runoff model for prediction of waterborne viral contamination in a small river catchment

NASA Astrophysics Data System (ADS)

Gelati, E.; Dommar, C.; Lowe, R.; Polcher, J.; Rodó, X.

2013-12-01

We present a lumped rainfall-runoff model aimed at providing useful information for the prediction of waterborne viral contamination in small rivers. Viral contamination of water bodies may occur because of the discharge of sewage effluents and of surface runoff over areas affected by animal waste loads. Surface runoff is caused by precipitation that cannot infiltrate due to its intensity and to antecedent soil water content. It may transport animal feces to adjacent water bodies and cause viral contamination. We model streamflow by separating it into two components: subsurface flow, which is produced by infiltrated precipitation; and surface runoff. The model estimates infiltrated and non-infiltrated precipitation and uses impulse-response functions to compute the corresponding fractions of streamflow. The developed methodologies are applied to the Glafkos river, whose catchment extends for 102 km2 and includes the city of Patra. Streamflow and precipitation observations are available at a daily time resolution. Waterborne virus concentration measurements were performed approximately every second week from the beginning of 2011 to mid 2012. Samples were taken at several locations: in river water upstream of Patras and in the urban area; in sea water at the river outlet and approximately 2 km south-west of Patras; in sewage effluents before and after treatment. The rainfall-runoff model was calibrated and validated using observed streamflow and precipitation data. The model contribution to waterborne viral contamination prediction was benchmarked by analyzing the virus concentration measurements together with the estimated surface runoff values. The presented methodology may be a first step towards the development of waterborne viral contamination alert systems. Predicting viral contamination of water bodies would benefit sectors such as water supply and tourism.

An update of the distribution of selected radiochemical and chemical constituents in perched ground water, Idaho National Laboratory, Idaho, Emphasis 1999-2001

USGS Publications Warehouse

Davis, Linda C.

2006-01-01

Radiochemical and chemical wastes generated at facilities at the Idaho National Laboratory (INL) were discharged since 1952 to infiltration ponds at the Reactor Technology Complex (RTC) (known as the Test Reactor Area [TRA] until 2005), and the Idaho Nuclear Technology and Engineering Center (INTEC) and buried at the Radioactive Waste Management Complex (RWMC). Disposal of wastewater to infiltration ponds and infiltration of surface water at waste burial sites resulted in formation of perched ground water in basalts and in sedimentary interbeds above the Snake River Plain aquifer. Perched ground water is an integral part of the pathway for waste-constituent migration to the aquifer. The U.S. Geological Survey (USGS), in cooperation with the U.S. Department of Energy, maintains ground-water monitoring networks at the INL to determine hydrologic trends, and to monitor the movement of radiochemical and chemical constituents in wastewater discharged from facilities to both perched ground water and the aquifer. This report presents an analysis of water-quality and water-level data collected from wells completed in perched ground water at the INL during 1999-2001, and summarizes historical disposal data and water-level-and water-quality trends. At the RTC, tritium, strontium-90, cesium-137, dissolved chromium, chloride, sodium, and sulfate were monitored in shallow and deep perched ground water. In shallow perched ground water, no tritium was detected above the reporting level. In deep perched ground water, tritium concentrations generally decreased or varied randomly during 1999-2001. During October 2001, tritium concentrations ranged from less than the reporting level to 39.4?1.4 picocuries per milliliter (pCi/mL). Reportable concentrations of tritium during July-October 2001 were smaller than the reported concentrations measured during July-December 1998. Tritium concentrations in water from wells at the RTC were likely affected by: well's distance from the radioactive-waste infiltration ponds (commonly referred to as the warm-waste ponds); water depth below the ponds; the amount of tritium discharged to radioactive-waste infiltration ponds in the past; discontinued use of radioactive-waste infiltration ponds; radioactive decay; and dilution from disposal of nonradioactive water. During 1999-2001, the strontium-90 concentrations in two wells completed in shallow perched water near the RTC exceeded the reporting level. Strontium-90 concentrations in water from wells completed in deep perched ground water at the RTC varied randomly with time. During October 2001, concentrations in water from five wells exceeded the reporting level and ranged from 2.8?0.7 picocuries per liter (pCi/L) in well USGS 63 to 83.8?2.1 pCi/L in well USGS 54. No reportable concentrations of cesium-137, chromium-51, or cobalt-60 were present in water samples from any of the shallow or deep wells at the RTC during 1999-2001. Dissolved chromium was not detected in shallow perched ground water at the RTC during 1999-2001. Concentrations of dissolved chromium during July-October 2001 in deep perched ground water near the RTC ranged from 10 micrograms per liter (?g/L) in well USGS 61 to 82 ?g/L in well USGS 55. The largest concentrations were in water from wells north and west of the radioactive-waste infiltration ponds. During July-October 2001, dissolved sodium concentrations ranged from 7 milligrams per liter (mg/L) in well USGS 78 to 20 mg/L in all wells except well USGS 68 (413 mg/L). Dissolved chloride concentrations in shallow perched ground water ranged from 10 mg/L in wells CWP 1, 3, and 4 to 53 mg/L in well TRA A 13 during 1999-2001. Dissolved chloride concentrations in deep perched ground water ranged from 5 mg/L in well USGS 78 to 91 mg/L in well USGS 73. The maximum dissolved sulfate concentration in shallow perched ground water was 419 mg/L in well CWP 1 during July 2000. Concentrations of dissolved sulfate in water from wells USGS 54, 60

Nonpoint Source: Agriculture

EPA Pesticide Factsheets

Agricultural runoff as a nonpoint source category of pollution. Resouces to learn more a bout conservation practices to reduce water quality impacts from storm water run off and ground water infiltration

The role of trees in urban stormwater management | Science ...

EPA Pesticide Factsheets

Urban impervious surfaces convert precipitation to stormwater runoff, which causes water quality and quantity problems. While traditional stormwater management has relied on gray infrastructure such as piped conveyances to collect and convey stormwater to wastewater treatment facilities or into surface waters, cities are exploring green infrastructure to manage stormwater at its source. Decentralized green infrastructure leverages the capabilities of soil and vegetation to infiltrate, redistribute, and otherwise store stormwater volume, with the potential to realize ancillary environmental, social, and economic benefits. To date, green infrastructure science and practice have largely focused on infiltration-based technologies that include rain gardens, bioswales, and permeable pavements. However, a narrow focus on infiltration overlooks other losses from the hydrologic cycle, and we propose that arboriculture – the cultivation of trees and other woody plants – deserves additional consideration as a stormwater control measure. Trees interact with the urban hydrologic cycle by intercepting incoming precipitation, removing water from the soil via transpiration, enhancing infiltration, and bolstering the performance of other green infrastructure technologies. However, many of these interactions are inadequately understood, particularly at spatial and temporal scales relevant to stormwater management. As such, the reliable use of trees for stormwater control depe

Non-uniform overland flow-infiltration model for roadside swales

NASA Astrophysics Data System (ADS)

García-Serrana, María; Gulliver, John S.; Nieber, John L.

2017-09-01

There is a need to quantify the hydrologic performance of vegetated roadside swales (drainage ditches) as stormwater control measures (SCMs). To quantify their infiltration performance in both the side slope and the channel of the swale, a model has been developed for coupling a Green-Ampt-Mein-Larson (GAML) infiltration submodel with kinematic wave submodels for both overland flow down the side slope and open channel flow for flow in the ditch. The coupled GAML submodel and overland flow submodel has been validated using data collected in twelve simulated runoff tests in three different highways located in the Minneapolis-St. Paul metropolitan area, MN. The percentage of the total water infiltrated into the side slope is considerably greater than into the channel. Thus, the side slope of a roadside swale is the main component contributing to the loss of runoff by infiltration and the channel primarily conveys the water that runs off the side slope, for the typical design found in highways. Finally, as demonstrated in field observations and the model, the fraction of the runoff/rainfall infiltrated (Vi∗) into the roadside swale appears to increase with a dimensionless saturated hydraulic conductivity (Ks∗), which is a function of the saturated hydraulic conductivity, rainfall intensity, and dimensions of the swale and contributing road surface. For design purposes, the relationship between Vi∗ and Ks∗ can provide a rough estimate of the fraction of runoff/rainfall infiltrated with the few essential parameters that appear to dominate the results.

Infiltration and hydraulic connections from the Niagara River to a fractured-dolomite aquifer in Niagara Falls, New York

USGS Publications Warehouse

Yager, R.M.; Kappel, W.M.

1998-01-01

The spatial distribution of hydrogen and oxygen stable-isotope values in groundwater can be used to distinguish different sources of recharge and to trace groundwater flow directions from recharge boundaries. This method can be particularly useful in fractured-rock settings where multiple lines of evidence are required to delineate preferential flow paths that result from heterogeneity within fracture zones. Flow paths delineated with stable isotopes can be combined with hydraulic data to form a more complete picture of the groundwater flow system. In this study values of ??D and ??18O were used to delineate paths of river-water infiltration into the Lockport Group, a fractured dolomite aquifer, and to compute the percentage of fiver water in groundwater samples from shallow bedrock wells. Flow paths were correlated with areas of high hydraulic diffusivity in the shallow bedrock that were delineated from water-level fluctuations induced by diurnal stage fluctuations in man-made hydraulic structures. Flow paths delineated with the stable-isotope and hydraulic data suggest that fiver infiltration reaches an unlined storm sewer in the bedrock through a drainage system that surrounds aqueducts carrying river water to hydroelectric power plants. This finding is significant because the storm sewer is the discharge point for contaminated groundwater from several chemical waste-disposal sites and the cost of treating the storm sewer's discharge could be reduced if the volume of infiltration from the river were decreased.The spatial distribution of hydrogen and oxygen stable-isotope values in groundwater can be used to distinguish different sources of recharge and to trace groundwater flow directions from recharge boundaries. This method can be particularly useful in fractured-rock settings where multiple lines of evidence are required to delineate preferential flow paths that result from heterogeneity within fracture zones. Flow paths delineated with stable isotopes can be combined with hydraulic data to form a more complete picture of the groundwater flow system. In this study values of ??D and ??18O were used to delineate paths of river-water infiltration into the Lockport Group, a fractured dolomite aquifer, and to compute the percentage of river water in groundwater samples from shallow bedrock wells. Flow paths were correlated with areas of high hydraulic diffusivity in the shallow bedrock that were delineated from water-level fluctuations induced by diurnal stage fluctuations in man-made hydraulic structures. Flow paths delineated with the stable-isotope and hydraulic data suggest that river infiltration reaches an unlined storm sewer in the bedrock through a drainage system that surrounds aqueducts carrying river water to hydroelectric power plants. This finding is significant because the storm sewer is the discharge point for contaminated groundwater from several chemical waste-disposal sites and the cost of treating the storm sewer's discharge could be reduced if the volume of infiltration from the river were decreased.

Artificial recharge through a thick, heterogeneous unsaturated zone

USGS Publications Warehouse

Izbicki, J.A.; Flint, A.L.; Stamos, C.L.

2008-01-01

Thick, heterogeneous unsaturated zones away from large streams in desert areas have not previously been considered suitable for artificial recharge from ponds. To test the potential for recharge in these settings, 1.3 ?? 10 6 m3 of water was infiltrated through a 0.36-ha pond along Oro Grande Wash near Victorville, California, between October 2002 and January 2006. The pond overlies a regional pumping depression 117 m below land surface and is located where thickness and permeability of unsaturated deposits allowed infiltration and saturated alluvial deposits were sufficiently permeable to allow recovery of water. Because large changes in water levels caused by nearby pumping would obscure arrival of water at the water table, downward movement of water was measured using sensors in the unsaturated zone. The downward rate of water movement was initially as high as 6 m/d and decreased with depth to 0.07 m/d; the initial time to reach the water table was 3 years. After the unsaturated zone was wetted, water reached the water table in 1 year. Soluble salts and nitrate moved readily with the infiltrated water, whereas arsenic and chromium were less mobile. Numerical simulations done using the computer program TOUGH2 duplicated the downward rate of water movement, accumulation of water on perched zones, and its arrival at the water table. Assuming 10 ?? 10 6 m3 of recharge annually for 20 years, a regional ground water flow model predicted water level rises of 30 m beneath the ponds, and rises exceeding 3 m in most wells serving the nearby urban area.

Magnetite Authigenesis and the Ancient Martian Atmosphere

NASA Astrophysics Data System (ADS)

Tosca, N. J.; Ahmed, I. A.; Ashpitel, A.; Hurowitz, J.

2017-12-01

Although the Curiosity rover has documented lacustrine sediments at Gale Crater, how liquid water became physically stable is unknown. The early Martian atmosphere is thought to have been dominated by CO2 [1], but the Curiosity rover has provided only ambiguous detections of carbonate minerals at abundances significantly less than 1 wt. % [2, 3], and climate models indicate that in the absence of additional components, multi-bar CO2 atmospheres could not have maintained surface temperatures above freezing. To constrain the composition of the ancient Martian atmosphere, we experimentally investigated the nucleation and growth kinetics of authigenic Fe(II)-minerals in Gale Crater mudstones. Experiments show that as basaltic waters experience pH increases above 8.0, a series of anoxic mineral transformations generates magnetite in days. Electrochemical and dissolved gas analyses show that one stage of this process, the conversion of Fe(OH)2 to green rust, generates H2(g). Experiments including dissolved CO2 show that, despite magnetite formation, Fe(II)-carbonate does not nucleate until significant supersaturation is reached, at PCO2 levels far above previous estimates. Our experimental observations imply that Gale Crater lakes could have been in contact with a CO2-rich atmosphere. In addition, geochemical calculations show that groundwater infiltration into lacustrine sediments triggered magnetite and H2(g) generation at Gale Crater (instead of Fe(II)-carbonate cementation). Groundwater infiltration is consistent with data from the Sheepbed member mudstones, and deep-water mudstones of the Murray formation, both of which contain abundant authigenic magnetite [2, 4]. Low temperature H2 production may have provided a globally significant but transient feedback for stabilizing liquid water on early Mars. Data collected to date by the Curiosity rover are consistent with both estimated timescales and climatic shifts associated with H2-induced warming. Low temperature H2 production also implies that a wide range of biologically relevant chemical reactions may have been operative on the early Martian surface. [1] J. Pollack, et al. (1987) Icarus 71, 203-24. [2] D. Vaniman et al., (2014) Science 343, 8. [3] D. Ming, et al., (2014) Science 343, 1245267. [4] J. Hurowitz, et al. (2017) Science 356, 922.

40 CFR 440.143 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... which may be discharged from an open-cut mine plant site shall not exceed the volume of infiltration... site shall not exceed the volume of infiltration, drainage and mine drainage waters which is in excess...

40 CFR 440.143 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... which may be discharged from an open-cut mine plant site shall not exceed the volume of infiltration... site shall not exceed the volume of infiltration, drainage and mine drainage waters which is in excess...

Influence of surface crusting on infiltration of a loess plateau soil

USDA-ARS?s Scientific Manuscript database

Surface sealing and crusting are common widespread processes that occur in many cultivated soils worldwide, especially in arid and semiarid regions. Soil crusting negatively affects water infiltration, increases surface runoff, reduces seedling emergence, restricts air exchange between the soil and ...

Shallow Groundwater Discharge into Urban Drains: Identifying the Missing Link to Define Urban Typologies for Impact Assessment of Urbanization on Water and Nutrient Balances

NASA Astrophysics Data System (ADS)

Ocampo, C. J.; Oldham, C. E.

2015-12-01

Groundwater and surface water (GW-SW) interaction in drains of many sandy coastal plain areas displays an ephemeral hydrological regime, as often shifts occur in their hydraulic functioning from a losing to a gaining water conditions upon the position of the surrounding shallow water table (SWT). Urbanization in such areas and stormwater management strategies enhancing infiltration have the potential to alter the infiltration rates and the subsurface water storage dynamics with consequences for the residence time of the water and nutrient transformations prior their discharge into receiving SW drains. Identifying first order control on the above processes will assist the improvement of assessment tools for better urban development. This work presents findings on the hydrodynamics of the GW-SW water exchange in two drains of the Perth Coastal Plain area (Western Australia, Australia) impacted by a SWT developing on a layered variable texture soil: a peri-urban drain and a restored living stream drain in urban residential area. A multi-technique approach was used to investigate water mass balance and fluxes over a reach scale and involved continuous records of hydrometric data for GW-SW interactions, passive tracers for water pathway identification, pore water temperature for vertical water exchange, and differential SW discharge using an Acoustic Doppler Current Profiler. Results highlighted differences in the GW-SW interactions between both drains under stormflow and baseflow conditions. A substantial increase of GW discharge into the drain coincided with the full development of a SWT over a seasonal scale at the peri-urban drain, which suggests a more natural water infiltration and redistribution in the subsurface. In contrast, a large volume of infiltrated rain water was discharged into the living stream over a period of few weeks regardless of the development of the surrounding SWT, which suggests the influence of underground pipe system in water redistribution. The results contributed to identify key physical parameters to define urban typologies, quantify the subsurface storage discharge and residence time, and finally assess the transport and transformations of nutrients using a generalised Damköhler number. Future work will populate the framework with other study cases.

Preferential flow, diffuse flow, and perching in an interbedded fractured-rock unsaturated zone

NASA Astrophysics Data System (ADS)

Nimmo, John R.; Creasey, Kaitlyn M.; Perkins, Kim S.; Mirus, Benjamin B.

2017-03-01

Layers of strong geologic contrast within the unsaturated zone can control recharge and contaminant transport to underlying aquifers. Slow diffuse flow in certain geologic layers, and rapid preferential flow in others, complicates the prediction of vertical and lateral fluxes. A simple model is presented, designed to use limited geological site information to predict these critical subsurface processes in response to a sustained infiltration source. The model is developed and tested using site-specific information from the Idaho National Laboratory in the Eastern Snake River Plain (ESRP), USA, where there are natural and anthropogenic sources of high-volume infiltration from floods, spills, leaks, wastewater disposal, retention ponds, and hydrologic field experiments. The thick unsaturated zone overlying the ESRP aquifer is a good example of a sharply stratified unsaturated zone. Sedimentary interbeds are interspersed between massive and fractured basalt units. The combination of surficial sediments, basalts, and interbeds determines the water fluxes through the variably saturated subsurface. Interbeds are generally less conductive, sometimes causing perched water to collect above them. The model successfully predicts the volume and extent of perching and approximates vertical travel times during events that generate high fluxes from the land surface. These developments are applicable to sites having a thick, geologically complex unsaturated zone of substantial thickness in which preferential and diffuse flow, and perching of percolated water, are important to contaminant transport or aquifer recharge.

Preferential flow, diffuse flow, and perching in an interbedded fractured-rock unsaturated zone

USGS Publications Warehouse

Nimmo, John R.; Creasey, Kaitlyn M; Perkins, Kimberlie; Mirus, Benjamin B.

2017-01-01

Layers of strong geologic contrast within the unsaturated zone can control recharge and contaminant transport to underlying aquifers. Slow diffuse flow in certain geologic layers, and rapid preferential flow in others, complicates the prediction of vertical and lateral fluxes. A simple model is presented, designed to use limited geological site information to predict these critical subsurface processes in response to a sustained infiltration source. The model is developed and tested using site-specific information from the Idaho National Laboratory in the Eastern Snake River Plain (ESRP), USA, where there are natural and anthropogenic sources of high-volume infiltration from floods, spills, leaks, wastewater disposal, retention ponds, and hydrologic field experiments. The thick unsaturated zone overlying the ESRP aquifer is a good example of a sharply stratified unsaturated zone. Sedimentary interbeds are interspersed between massive and fractured basalt units. The combination of surficial sediments, basalts, and interbeds determines the water fluxes through the variably saturated subsurface. Interbeds are generally less conductive, sometimes causing perched water to collect above them. The model successfully predicts the volume and extent of perching and approximates vertical travel times during events that generate high fluxes from the land surface. These developments are applicable to sites having a thick, geologically complex unsaturated zone of substantial thickness in which preferential and diffuse flow, and perching of percolated water, are important to contaminant transport or aquifer recharge.

Soil sealing and vesicular layer formation as initial structure development and its effect on infiltration

NASA Astrophysics Data System (ADS)

Badorreck, A.; Gerke, H. H.; Weller, U.; Vontobel, P.

2009-04-01

In the Lusatia mining district (NE-Germany) an artificial catchment was constructed to study initial ecosystem development and runoff generation. As a key process in this early stage, we investigate the surface structure dynamics as it strongly influences erosion, infiltration, matter dynamics, and vegetation establishment. The presented work focuses on observations of soil pore structure formation at the surface at five sites in the catchment and in an adjacent "younger" area composed of comparable sediments. Moreover we've conducted infiltration experiments in the lab and field to relate the soil pore structure to the hydraulic properties. The surface soil was sampled in cylindrical rings (10 cm³) down to 2 cm depth from which bulk density profiles were obtained using X-ray computed tomography (CT) (at UFZ- Halle, Germany) with a resolution of 0.084 mm. The influence of structure on infiltration was investigated using neutron radiography (at the NEUTRA facility of the Paul-Scherrer-Institut, Villigen, Switzerland) to visualise two-dimensional (2D) infiltration patterns. The slab-type samples were equilibrated to different initial water contents and then exposed to drip irrigation (to simulate rainfall) while a series of neutron radiographs were taken. In addition, field measurements with a miniature tension infiltrometer were conduced. The micro-tomographies exhibit formation of surface sealing whose thickness and intensity vary with silt and clay content. The CT images show several coarser- and finer-textured micro-layers at the sample surfaces that were formed as a consequence of repeated washing in of finer particles in underlying coarser sediment. In micro-depressions, the uppermost layers consist of sorted fine sand and silt due to wind erosion. Similar as for desert pavements, a vesicular pore structure developed in these sediments on top, but also scattered in fine sand- and silt-enriched micro-layers. The infiltration rates were severely affected by the surface crusts; however, the rates were independent of the vesicular pore layer.

Mobilization of microspheres from a fractured soil during intermittent infiltration events

USGS Publications Warehouse

Mohanty, Sanjay; Bulicek, Mark; Metge, David W.; Harvey, Ronald W.; Ryan, Joseph N.; Boehm, Alexandria B.

2015-01-01

Pathogens or biocolloids mobilized in the vadose zone may consequently contaminate groundwater. We found that microspheres were mobilized from a fractured soil during intermittent rainfall and the mobilization was greater when the microsphere size was larger and when the soil had greater water permeability.The vadose zone filters pathogenic microbes from infiltrating water and consequently protects the groundwater from possible contamination. In some cases, however, the deposited microbes may be mobilized during rainfall and migrate into the groundwater. We examined the mobilization of microspheres, surrogates for microbes, in an intact core of a fractured soil by intermittent simulated rainfall. Fluorescent polystyrene microspheres of two sizes (0.5 and 1.8 mm) and Br− were first applied to the core to deposit the microspheres, and then the core was subjected to three intermittent infiltration events to mobilize the deposited microspheres. Collecting effluent samples through a 19-port sampler at the base of the core, we found that water flowed through only five ports, and the flow rates varied among the ports by a factor of 12. These results suggest that flow paths leading to the ports had different permeabilities, partly due to macropores. Although 40 to 69% of injected microspheres were retained in the core during their application, 12 to 30% of the retained microspheres were mobilized during three intermittent infiltration events. The extent of microsphere mobilization was greater in flow paths with greater permeability, which indicates that macropores could enhance colloid mobilization during intermittent infiltration events. In all ports, the 1.8-mm microspheres were mobilized to a greater extent than the 0.5-mm microspheres, suggesting that larger colloids are more likely to mobilize. These results are useful in assessing the potential of pathogen mobilization and colloid-facilitated transport of contaminants in the subsurface under natural infiltration events.

A reaction-transport model for calcite precipitation and evaluation of infiltration fluxes in unsaturated fractured rock.

PubMed

Xu, Tianfu; Sonnenthal, Eric; Bodvarsson, Gudmundur

2003-06-01

The percolation flux in the unsaturated zone (UZ) is an important parameter addressed in site characterization and flow and transport modeling of the potential nuclear-waste repository at Yucca Mountain, NV, USA. The US Geological Survey (USGS) has documented hydrogenic calcite abundances in fractures and lithophysal cavities at Yucca Mountain to provide constraints on percolation fluxes in the UZ. The purpose of this study was to investigate the relationship between percolation flux and measured calcite abundances using reactive transport modeling. Our model considers the following essential factors affecting calcite precipitation: (1) infiltration, (2) the ambient geothermal gradient, (3) gaseous CO(2) diffusive transport and partitioning in liquid and gas phases, (4) fracture-matrix interaction for water flow and chemical constituents, and (5) water-rock interaction. Over a bounding range of 2-20 mm/year infiltration rate, the simulated calcite distributions capture the trend in calcite abundances measured in a deep borehole (WT-24) by the USGS. The calcite is found predominantly in fractures in the welded tuffs, which is also captured by the model simulations. Simulations showed that from about 2 to 6 mm/year, the amount of calcite precipitated in the welded Topopah Spring tuff is sensitive to the infiltration rate. This dependence decreases at higher infiltration rates owing to a modification of the geothermal gradient from the increased percolation flux. The model also confirms the conceptual model for higher percolation fluxes in the fractures compared to the matrix in the welded units, and the significant contribution of Ca from water-rock interaction. This study indicates that reactive transport modeling of calcite deposition can yield important constraints on the unsaturated zone infiltration-percolation flux and provide useful insight into processes such as fracture-matrix interaction as well as conditions and parameters controlling calcite deposition.

Effect of oil pollution on fresh groundwater in Kuwait

NASA Astrophysics Data System (ADS)

Al-Sulaimi, J.; Viswanathan, M. N.; Székely, F.

1993-11-01

Massive oil fires in Kuwait were the aftermath of the Gulf War. This resulted in the pollution of air, water, and soil, the magnitude of which is unparalleled in the history of mankind. Oil fires damaged several oil well heads, resulting in the flow of oil, forming large oil lakes. Products of combustion from oil well fires deposited over large areas. Infiltrating rainwater, leaching out contaminants from oil lakes and products of combustion at ground surface, can reach the water table and contaminate the groundwater. Field investigations, supported by laboratory studies and mathematical models, show that infiltration of oil from oil lakes will be limited to a depth of about 2 m from ground surface. Preliminary mathematical models showed that contaminated rainwater can infiltrate and reach the water table within a period of three to four days, particularly at the Raudhatain and Umm Al-Aish regions. These are the only regions in Kuwait where fresh groundwater exists. After reaching the water table, the lateral movement of contaminants is expected to be very slow under prevailing hydraulic gradients. Groundwater monitoring at the above regions during 1992 showed minor levels of vanadium, nickel, and total hydrocarbons at certain wells. Since average annual rainfall in the region is only 120 mm/yr, groundwater contamination due to the infiltration of contaminated rainwater is expected to be a long-term one.

A Stand-Alone Demography and Landscape Structure Module for Earth System Models: Integration with Inventory Data from Temperate and Boreal Forests

NASA Astrophysics Data System (ADS)

Hess, L.; Basso, B.; Hinckley, E. L. S.; Robertson, G. P.; Matson, P. A.

2014-12-01

In the coming century, the proportion of total rainfall that falls in heavy storm events is expected to increase in many areas, especially in the US Midwest, a major agricultural region. These changes in rainfall patterns may have consequences for hydrologic flow and nutrient losses, especially in agricultural soils, with potentially negative consequences for receiving ground- and surface waters. We used a tracer experiment to examine how more extreme rainfall patterns may affect the movement of water and solutes through an agricultural soil profile in the upper Midwest, and to what extent tillage may moderate these effects. Two rainfall patterns were created with 5m x 5m rainout shelters at the Kellogg Biological Station LTER site in replicated plots with either conventional tillage or no-till management. Control rainfall treatments received water 3x per week, and extreme rainfall treatments received the same total amount of water but once every two weeks, to simulate less frequent but larger storms. In April 2015, potassium bromide (KBr) was added as a conservative tracer of water flow to all plots, and Br- concentrations in soil water at 1.2m depth were measured weekly from April through July. Soil water Br- concentrations increased and peaked more quickly under the extreme rainfall treatment, suggesting increased infiltration and solute transfer to depth compared to soils exposed to control rainfall patterns. Soil water Br- also increased and peaked more quickly in no-till than in conventional tillage treatments, indicating differences in flow paths between management systems. Soil moisture measured every 15 minutes at 10, 40, and 100cm depths corroborates tracer experiment results: rainfall events simulated in extreme rainfall treatments led to large increases in deep soil moisture, while the smaller rainfall events simulated under control conditions did not. Deep soil moisture in no-till treatments also increased sooner after water application as compared to in conventional soils. Our results suggest that exposure to more extreme rainfall patterns will likely increase infiltration depth and nutrient losses in agricultural soils. In particular, soils under no-till management, which leads to development of preferential flow paths, may be particularly vulnerable to vertical nutrient losses.

Ranking agricultural practices on soil water improvements: a meta-analysis

NASA Astrophysics Data System (ADS)

Basche, A.; DeLonge, M. S.; Gonzalez, J.

2016-12-01

Increased rainfall variability is well documented in the historic record and predicted to intensify with future climate change. Managing excess water in periods of heavy rain and a lack of water in periods of inadequate precipitation will continue to be a challenge. Improving soil resiliency through increased water storage is a promising strategy to combat effects of both rainfall extremes. The goal of this research is to quantify to what extent various conservation and ecological practices can improve soil hydrology. We are conducting a global meta-analysis focused on studies where conservation and ecological practices are compared to more conventional management. To date we have analyzed 100 studies with more than 450 paired comparisons to understand the effect of management on water infiltration rates, a critical process that ensures water enters the soil profile for crop use, water storage and runoff prevention. The database will be expanded to include studies measuring soil porosity and the water retained at field capacity. Statistical analysis has been done both with both a bootstrap method and a mixed model that weights studies based on precision while accounting for between-study variation. We find that conservation and ecological practices, ranging from no-till, cover crops, crop rotation, perennial crops and agroforestry, on average significantly increased water infiltration rates relative to more conventional practice controls (mean of 75%, standard error 25%). There were significant differences between practices, where perennial and agroforestry systems show the greatest potential for improving water infiltration rates (> 100% increase). Cover crops also lead to a significant increase in water infiltration rates (> 60%) while crop rotations and no-till systems did not consistently demonstrate increases. We also found that studies needed to include alternative management for more than two years to detect a significant increase. Overall this global meta-analysis improves understanding of how alternative management, notably the use of continuous cover in agricultural systems, improves water dynamics. Policies should be designed in a way that allows agricultural producers to prioritize and implement practices that offer greater water conservation while maintaining crop productivity.

Determination of near-saturated hydraulic conductivity by automated minidisk infiltrometer

NASA Astrophysics Data System (ADS)

Klipa, Vladimir; Snehota, Michal; Dohnal, Michal; Zumr, David

2013-04-01

Numerical models in surface and subsurface hydrology require knowledge of infiltration properties of soils for their routine use in the field of water management, environmental protection or agriculture. A new automated tension infiltration module has been designed at the Faculty of Civil Engineering, Czech Technical University in Prague to facilitate the measurements of near-saturated hydraulic conductivity. In the proposed infiltration module the amount of infiltrated water is registered via changes of buoyant force of stationary float attached to the load cell. Presented setup consists of six mini-disk infiltrometer modules held in the light aluminum frame and two Mariotte's bottles. Three infiltrometer modules connected to each Mariotte's bottle allow performing six simultaneous measurements at two different pressure heads. Infiltration modules are connected to the automatic data logging system and consist of: plastic cover with the integrated load cell and the float, reservoir tube (external diameter of 50 mm), and sintered stainless steel plate (diameter of 44.5 mm). The newly developed device was used for determination of near-saturated hydraulic conductivity of soils in experimental catchments Uhlirska (Jizera Mountains, Northern Bohemia) and Kopaninsky creek (Bohemian-Moravian Highlands). The acquired data show a good agreement with the data obtained from previous measurements.

Transient Infiltration Analysis for Infinite Slopes using the Modified Function of Unsaturated Hydraulic Conductivity

NASA Astrophysics Data System (ADS)

Oh, Seboong; Achmad Zaky, Fauzi; Mog Park, Young

2016-04-01

The hydraulic behaviors in the soil layer are crucial to the transient infiltration analysis into natural slopes, in which unsaturated hydraulic conductivity (HC) can be evaluated theoretically from soil water retention curves (SWRC) by Mualem's equation. In the nonlinear infiltration analysis, the solution by some of smooth SWRCs is not converge for heavy rainfall condition, since the gradient of HCs is extremely steep near saturation. The van Genuchten's SWRC model has been modified near saturation and subsequently an analytical HC function was proposed to improve the van Genuchten-Mualem HC. Using the examples on 1-D infiltration analysis by the modified HC model, it is validated that any solutions can be converged for various rainfall conditions to keep numerical stability. Stability analysis based on unsaturated effective stress could simulate the infinite slope failure by the proposed HC model. The pore water pressure and the ratio of saturation increased from the surface to shallow depth (˜1m) and the factor of safety decreased gradually due to infiltration. Acknowledgements This research is supported by grants from Korean NRF (2012M3A2A1050974 and 2015R1A2A2A01), which are greatly appreciated.

Intracavitary moderator balloon combined with (252)Cf brachytherapy and boron neutron capture therapy, improving dosimetry in brain tumour and infiltrations.

PubMed

Brandão, S F; Campos, T P R

2015-07-01

This article proposes a combination of californium-252 ((252)Cf) brachytherapy, boron neutron capture therapy (BNCT) and an intracavitary moderator balloon catheter applied to brain tumour and infiltrations. Dosimetric evaluations were performed on three protocol set-ups: (252)Cf brachytherapy combined with BNCT (Cf-BNCT); Cf-BNCT with a balloon catheter filled with light water (LWB) and the same set-up with heavy water (HWB). Cf-BNCT-HWB has presented dosimetric advantages to Cf-BNCT-LWB and Cf-BNCT in infiltrations at 2.0-5.0 cm from the balloon surface. However, Cf-BNCT-LWB has shown superior dosimetry up to 2.0 cm from the balloon surface. Cf-BNCT-HWB and Cf-BNCT-LWB protocols provide a selective dose distribution for brain tumour and infiltrations, mainly further from the (252)Cf source, sparing the normal brain tissue. Malignant brain tumours grow rapidly and often spread to adjacent brain tissues, leading to death. Improvements in brain radiation protocols have been continuously achieved; however, brain tumour recurrence is observed in most cases. Cf-BNCT-LWB and Cf-BNCT-HWB represent new modalities for selectively combating brain tumour infiltrations and metastasis.

Application and evaluation of the washing effect in the collector well using pilot plant with washing device

NASA Astrophysics Data System (ADS)

Cho, K. H.; Kim, B. J.; Choi, N. C.; Lee, S. J.; Lee, B. H.

2012-04-01

Riverbed/bank filtration (RBF) is a natural process used as a first step in drinking water treatment. RBF systems consist of well fields that draw water from an aquifer that is hydraulically connected to surface waters. The benefits of RBF are multiple and include a reduction of turbidity, total coliform, microbial contaminants natural organic matter, and organic contaminants. Some of the disadvantages of RBF include the difficulty of preventing river water from infiltrating the aquifer in in-stances of severe river contamination, the geochemical reaction of the infiltrate with aquifer materials that may raise the aqueous concentrations of Fe2+, Mn2+, As, NH4+, CH4, Ca2+ and HCO3- , and clogging of the riverbed. For example, has demonstrated that riverbed clogging may decrease the specific capacity of RBF wells (flow reduction in the collector well etc.). The objective of this study is to optimization and evaluation the washing effect on various nozzle type and intervals, soil retention rate in the collector well using pilot plant with washing device for prevention flow reduction in the collector well. The Pilot plant experiments were conducted under various conditions; two kinds nozzle type (spray nozzle of circle type (single - Full Cone, multi - Hollow Cone) and spray nozzle of fan shape type (Veejet)), two different nozzle intervals (200 mm, 400mm) and a various soil retention rate in the collector well (10 ~ 40%). The results of experiment showed that in the nozzle type case, the washing effect of the veeject nozzle was more effective than other (Full Cone, Hollow Cone) nozzle through spray results (range, strength and height). In the nozzle interval conditions, washing effect is 200 mm better than 400 mm through spray distance and soil height. The washing efficiency in the collector well increased on soil retention rate decreased and the nozzle injection pressure increased using washing device

Coupling distributed stormwater collection and managed aquifer recharge: Field application and implications.

PubMed

Beganskas, S; Fisher, A T

2017-09-15

Groundwater is increasingly important for satisfying California's growing fresh water demand. Strategies like managed aquifer recharge (MAR) can improve groundwater supplies, mitigating the negative consequences of persistent groundwater overdraft. Distributed stormwater collection (DSC)-MAR projects collect and infiltrate excess hillslope runoff before it reaches a stream, focusing on 40-400 ha drainage areas (100-1000 ac). We present results from six years of DSC-MAR operation-including high resolution analyses of precipitation, runoff generation, infiltration, and sediment transport-and discuss their implications for regional resource management. This project generated significant water supply benefit over six years, including an extended regional drought, collecting and infiltrating 5.3 × 10 5  m 3 (426 ac-ft). Runoff generation was highly sensitive to sub-daily storm frequency, duration, and intensity, and a single intense storm often accounted for a large fraction of annual runoff. Observed infiltration rates varied widely in space and time. The basin-average infiltration rate during storms was 1-3 m/d, with point-specific rates up to 8 m/d. Despite efforts to limit sediment load, 8.2 × 10 5  kg of fine-grained sediment accumulated in the infiltration basin over three years, likely reducing soil infiltration capacity. Periodic removal of accumulated material, better source control, and/or improved sediment detention could mitigate this effect in the future. Regional soil analyses can maximize DSC-MAR benefits by identifying high-infiltration capacity features and characterizing upland sediment sources. A regional network of DSC-MAR projects could increase groundwater supplies while contributing to improved groundwater quality, flood mitigation, and stakeholder engagement. Copyright © 2017 Elsevier Ltd. All rights reserved.

A DRBEM for steady infiltration from periodic semi-circular channels with two different types of roots distribution

NASA Astrophysics Data System (ADS)

Solekhudin, Imam; Sumardi

2017-05-01

In this study, problems involving steady Infiltration from periodic semicircular channels with root-water uptake function are considered. These problems are governed by Richards equation. This equation can be studied more conveniently by transforming the equation into a modified Helmholtz equation. In these problems, two different types of root-water uptake are considered. A dual reciprocity boundary element method (DRBEM) with a predictor-corrector scheme is used to solve the modified Helmholtz equation numerically. Using the solution obtained, numerical values of suction potential and root-water uptake function can be computed. In addition, amount of water absorbed by the different plant roots distribution can also be computed and compared.

Update to permeable pavement research at the Edison ...

EPA Pesticide Factsheets

Abstract: The EPA’s Urban Watershed Management Branch (UWMB) has been monitoring the permeable pavement demonstration site at the Edison Environmental Center, NJ since 2010. This site has three different types of permeable pavement including: interlocking concrete permeable pavers; porous concrete; and permeable asphalt. The parking lot is instrumented with water content reflectometers and thermistors for continuous monitoring and has four lined sections for each surface to capture permeable pavement infiltrate for water quality analyses.Previous technical releases concerning the demonstration site focused on monitoring techniques, observed chloride and nutrient concentrations, and infiltration and evaporation rates. Thispresentation summarizes past findings and addresses current water quality efforts. This presentation summarizes past findings and addresses current water quality efforts.

Simulation of groundwater flow and interaction of groundwater and surface water on the Lac du Flambeau Reservation, Wisconsin

USGS Publications Warehouse

Juckem, Paul F.; Fienen, Michael N.; Hunt, Randall J.

2014-01-01

The Lac du Flambeau Band of Lake Superior Chippewa and Indian Health Service are interested in improving the understanding of groundwater flow and groundwater/surface-water interaction on the Lac du Flambeau Reservation (Reservation) in southwest Vilas County and southeast Iron County, Wisconsin, with particular interest in an understanding of the potential for contamination of groundwater supply wells and the fate of wastewater that is infiltrated from treatment lagoons on the Reservation. This report describes the construction, calibration, and application of a regional groundwater flow model used to simulate the shallow groundwater flow system of the Reservation and water-quality results for groundwater and surface-water samples collected near a system of waste-water-treatment lagoons. Groundwater flows through a permeable glacial aquifer that ranges in thickness from 60 to more than 200 feet (ft). Seepage and drainage lakes are common in the area and influence groundwater flow patterns on the Reservation. A two-dimensional, steady-state analytic element groundwater flow model was constructed using the program GFLOW. The model was calibrated by matching target water levels and stream base flows through the use of the parameter-estimation program, PEST. Simulated results illustrate that groundwater flow within most of the Reservation is toward the Bear River and the chain of lakes that feed the Bear River. Results of analyses of groundwater and surface-water samples collected downgradient from the wastewater infiltration lagoons show elevated levels of ammonia and dissolved phosphorus. In addition, wastewater indicator chemicals detected in three downgradient wells and a small downgradient stream indicate that infiltrated wastewater is moving southwest of the lagoons toward Moss Lake. Potential effects of extended wet and dry periods (within historical ranges) were evaluated by adjusting precipitation and groundwater recharge in the model and comparing the resulting simulated lake stage and water budgets to stages and water budgets from the calibrated model. Simulated lake water budgets and water level changes illustrate the importance of understanding the position of a lake within the hydrologic system (headwater or downstream), the type of lake (surface-water drainage or seepage lake), and the role of groundwater in dampening the effects of large-scale changes in weather patterns on lake levels. Areas contributing recharge to drinking-water supply wells on the Reservation were delineated using forward particle tracking from the water table to the well. Monte Carlo uncertainty analyses were used to produce maps showing the probability of groundwater capture for areas around each well nest. At the Main Pumphouse site near the Village of Lac du Flambeau, most of the area contributing recharge to the wells occurs downgradient from a large wetland between the wells and the wastewater infiltration lagoons. Nonetheless, a small potential for the wells to capture infiltrated wastewater is apparent when considering uncertainty in the model parameter values. At the West Pumphouse wells south of Flambeau Lake, most of the area contributing recharge is between the wells and Tippecanoe Lake. The extent of infiltrated wastewater from two infiltration lagoons was tracked using the groundwater flow model and Monte Carlo uncertainty analyses. Wastewater infiltrated from the lagoons flows predominantly south toward Moss Lake as it integrates with the regional groundwater flow system. The wastewater-plume-extent simulations support the area-contributing-recharge simulations, indicating that there is a possibility, albeit at low probability, that some wastewater could be captured by water-supply wells. Comparison of simulated water-table contours indicate that the lagoons may mound the water table approximately 4 ft, with diminishing levels of mounding outward from the lagoons. Four scenarios, representing potential alternatives for wastewater management, were simulated (at current discharge rates) to evaluate the potential extent of wastewater in the aquifer and discharge to surface-water bodies associated with each management scenario. Wastewater simulated to infiltrate through a hypothetical diffuser below a wetland south of the current lagoons appears to discharge to the overlying wetland and would likely discharge to Moss Lake as overland flow. Wastewater simulated to discharge to a small lake (Mindy Lake) between Moss and Fence Lakes appears to spread radically over a large area between the lakes. Wastewater simulated to discharge to lagoons south and northeast of the current lagoons also appears to spread radially, but the areas of the aquifer with the highest probability of encountering waste-water contamination would likely be between the lagoons and the nearest lake, where the wastewater would eventually discharge. Probability results for the wastewater-plume-extent scenarios are sensitive to the number of mathematical water particles used to represent infiltrating wastewater and the level of detail in the synthetic grid used for the probability analysis. Thus, probability results from wastewater-plume-extent simulations are qualitative only; however, it is expected that illustrations of relatively high or low probability will be useful as a general guide for decision making. Management problems requiring quantitative estimates of probability are best re-cast into problems evaluating the area that contributes recharge to the location of interest, which is not dependent upon the number of simulated particles or the resolution of a synthetic grid.

Rainfall-runoff characteristics and effects of increased urban density on streamflow and infiltration in the eastern part of the San Jacinto River basin, Riverside County, California

USGS Publications Warehouse

Guay, Joel R.

2002-01-01

To better understand the rainfall-runoff characteristics of the eastern part of the San Jacinto River Basin and to estimate the effects of increased urbanization on streamflow, channel infiltration, and land-surface infiltration, a long-term (1950?98) time series of monthly flows in and out of the channels and land surfaces were simulated using the Hydrologic Simulation Program- FORTRAN (HSPF) rainfall-runoff model. Channel and land-surface infiltration includes rainfall or runoff that infiltrates past the zone of evapotranspiration and may become ground-water recharge. The study area encompasses about 256 square miles of the San Jacinto River drainage basin in Riverside County, California. Daily streamflow (for periods with available data between 1950 and 1998), and daily rainfall and evaporation (1950?98) data; monthly reservoir storage data (1961?98); and estimated mean annual reservoir inflow data (for 1974 conditions) were used to calibrate the rainfall-runoff model. Measured and simulated mean annual streamflows for the San Jacinto River near San Jacinto streamflow-gaging station (North-South Fork subbasin) for 1950?91 and 1997?98 were 14,000 and 14,200 acre-feet, respectively, a difference of 1.4 percent. The standard error of the mean for measured and simulated annual streamflow in the North-South Fork subbasin was 3,520 and 3,160 acre-feet, respectively. Measured and simulated mean annual streamflows for the Bautista Creek streamflow-gaging station (Bautista Creek subbasin) for 1950?98 were 980 acre-feet and 991 acre-feet, respectively, a difference of 1.1 percent. The standard error of the mean for measured and simulated annual streamflow in the Bautista Creek subbasin was 299 and 217 acre-feet, respectively. Measured and simulated annual streamflows for the San Jacinto River above State Street near San Jacinto streamflow-gaging station (Poppet subbasin) for 1998 were 23,400 and 23,500 acre-feet, respectively, a difference of 0.4 percent. The simulated mean annual streamflow for the State Street gaging station at the outlet of the study basin and the simulated mean annual basin infiltration (combined infiltration from all the channels and land surfaces) were 8,720 and 41,600 acre-feet, respectively, for water years 1950-98. Simulated annual streamflow at the State Street gaging station ranged from 16.8 acre-feet in water year 1961 to 70,400 acre-feet in water year 1993, and simulated basin infiltration ranged from 2,770 acre-feet in water year 1961 to 149,000 acre-feet in water year 1983.The effects of increased urbanization on the hydrology of the study basin were evaluated by increasing the size of the effective impervious and non-effective impervious urban areas simulated in the calibrated rainfall-runoff model by 50 and 100 percent, respectively. The rainfall-runoff model simulated a long-term time series of monthly flows in and out of the channels and land surfaces using daily rainfall and potential evaporation data for water years 1950?98. Increasing the effective impervious and non-effective impervious urban areas by 100 percent resulted in a 5-percent increase in simulated mean annual streamflow at the State Street gaging station, and a 2.2-percent increase in simulated basin infiltration. Results of a frequency analysis of the simulated annual streamflow at the State Street gaging station showed that when effective impervious and non-effective impervious areas were increased 100 percent, simulated annual streamflow increased about 100 percent for low-flow conditions and was unchanged for high-flow conditions. The simulated increase in streamflow at the State Street gaging station potentially could infiltrate along the stream channel further downstream, outside of the model area.

Effects of stormwater infiltration on quality of groundwater beneath retention and detention basins

USGS Publications Warehouse

Fischer, D.; Charles, E.G.; Baehr, A.L.

2003-01-01

Infiltration of storm water through detention and retention basins may increase the risk of groundwater contamination, especially in areas where the soil is sandy and the water table shallow, and contaminants may not have a chance to degrade or sorb onto soil particles before reaching the saturated zone. Groundwater from 16 monitoring wells installed in basins in southern New Jersey was compared to the quality of shallow groundwater from 30 wells in areas of new-urban land use. Basin groundwater contained much lower levels of dissolved oxygen, which affected concentrations of major ions. Patterns of volatile organic compound and pesticide occurrence in basin groundwater reflected the land use in the drainage areas served by the basins, and differed from patterns in background samples, exhibiting a greater occurrence of petroleum hydrocarbons and certain pesticides. Dilution effects and volatilization likely decrease the concentration and detection frequency of certain compounds commonly found in background groundwater. High recharge rates in storm water basins may cause loading factors to be substantial even when constituent concentrations in infiltrating storm water are relatively low.

Effect of irrigation with treated wastewater on soil chemical properties and infiltration rate.

PubMed

Bedbabis, Saida; Ben Rouina, Béchir; Boukhris, Makki; Ferrara, Giuseppe

2014-01-15

In Tunisia, water scarcity is one of the major constraints for agricultural activities. The reuse of treated wastewater (TWW) in agriculture can be a sustainable solution to face water scarcity. The research was conducted for a period of four years in an olive orchard planted on a sandy soil and subjected to irrigation treatments: a) rain-fed conditions (RF), as control b) well water (WW) and c) treated wastewater (TWW). In WW and TWW treatments, an annual amount of 5000 m(3) ha(-1) of water was supplied to the orchard. Soil samples were collected at the beginning of the study and after four years for each treatment. The main soil properties such as electrical conductivity (EC), pH, soluble cations, chloride (Cl(-)), sodium adsorption ratio (SAR), organic matter (OM) as well as the infiltration rate were investigated. After four years, either a significant decrease of pH and infiltration rate or a significant increase of OM, SAR and EC were observed in the soil subjected to treated wastewater treatment. Copyright © 2013. Published by Elsevier Ltd.

Importance of unsaturated zone flow for simulating recharge in a humid climate

USGS Publications Warehouse

Hunt, R.J.; Prudic, David E.; Walker, J.F.; Anderson, M.P.

2008-01-01

Transient recharge to the water table is often not well understood or quantified. Two approaches for simulating transient recharge in a ground water flow model were investigated using the Trout Lake watershed in north-central Wisconsin: (1) a traditional approach of adding recharge directly to the water table and (2) routing the same volume of water through an unsaturated zone column to the water table. Areas with thin (less than 1 m) unsaturated zones showed little difference in timing of recharge between the two approaches; when water was routed through the unsaturated zone, however, less recharge was delivered to the water table and more discharge occurred to the surface because recharge direction and magnitude changed when the water table rose to the land surface. Areas with a thick (15 to 26 m) unsaturated zone were characterized by multimonth lags between infiltration and recharge, and, in some cases, wetting fronts from precipitation events during the fall overtook and mixed with infiltration from the previous spring snowmelt. Thus, in thicker unsaturated zones, the volume of water infiltrated was properly simulated using the traditional approach, but the timing was different from simulations that included unsaturated zone flow. Routing of rejected recharge and ground water discharge at land surface to surface water features also provided a better simulation of the observed flow regime in a stream at the basin outlet. These results demonstrate that consideration of flow through the unsaturated zone may be important when simulating transient ground water flow in humid climates with shallow water tables.

Research on the infiltration processes of lawn soils of the Babao River in the Qilian Mountain.

PubMed

Li, GuangWen; Feng, Qi; Zhang, FuPing; Cheng, AiFang

2014-01-01

Using a Guelph Permeameter, the soil water infiltration processes were analyzed in the Babao River of the Qilian Mountain in China. The results showed that the average soil initial infiltration and the steady infiltration rates in the upstream reaches of the Babao River are 1.93 and 0.99 cm/min, whereas those of the middle area are 0.48 cm/min and 0.21 cm/min, respectively. The infiltration processes can be divided into three stages: the rapidly changing stage (0-10 min), the slowly changing stage (10-30 min) and the stabilization stage (after 30 min). We used field data collected from lawn soils and evaluated the performances of the infiltration models of Philip, Kostiakov and Horton with the sum of squared error, the root mean square error, the coefficient of determination, the mean error, the model efficiency and Willmott's index of agreement. The results indicated that the Kostiakov model was most suitable for studying the infiltration process in the alpine lawn soils.

High-resolution stable isotope monitoring reveals differential vegetation-soil water feedbacks among plant functional types

NASA Astrophysics Data System (ADS)

Volkmann, T. H. M.; Haberer, K.; Troch, P. A. A.; Gessler, A.; Weiler, M.

2016-12-01

Understanding the linked dynamics of rain water recharge to soils and its utilization by plants is critical for predicting the impact of climate and land use changes on the productivity of ecosystems and the hydrologic cycle. While plants require vast quantities of water from the soil to sustain growth and function, they exert important direct and indirect controls on the movement of water through the rooted soil horizons, thereby potentially affecting their own resource availability. However, the specific ecohydrological belowground processes associated with different plant types and their rooting systems have been difficult to quantify with traditional methods. Here, we report on the use of techniques for monitoring stable isotopes in soil and plant water pools that allow us to track water infiltration and root uptake dynamics non-destructively and in high resolution. The techniques were applied in controlled rain pulse experiments with distinct plant types (grass, deciduous trees, grapevine) that we let develop on an initially uniform soil for two years. Our results show that plant species and types differed widely in their plasticity and pattern of root uptake under variable water availability. Thereby, and through notably co-acting indirect effects related to differential root system traits and co-evolution of soil properties, the different plants induced contrasting hydrological dynamics in the soil they had inhabited for only a short period of time. Taken together, our data suggest that the studied soil-vegetation systems evolved a positive infiltration-uptake feedback in which hydrological flow pathways underlying different species diverged in a way that complemented their specific water utilization strategy. Such a feedback could present an indirect competitive mechanism by which plants improve their own water supply and modulate hydrological cycling at the land surface. The ability to directly measure this feedback using in situ isotope methodology highlights the great potential for stable isotope research to improve our understanding of the soil-vegetation-atmosphere system.

Stability of infinite slopes under transient partially saturated seepage conditions

NASA Astrophysics Data System (ADS)

Godt, Jonathan W.; ŞEner-Kaya, BaşAk; Lu, Ning; Baum, Rex L.

2012-05-01

Prediction of the location and timing of rainfall-induced shallow landslides is desired by organizations responsible for hazard management and warnings. However, hydrologic and mechanical processes in the vadose zone complicate such predictions. Infiltrating rainfall must typically pass through an unsaturated layer before reaching the irregular and usually discontinuous shallow water table. This process is dynamic and a function of precipitation intensity and duration, the initial moisture conditions and hydrologic properties of the hillside materials, and the geometry, stratigraphy, and vegetation of the hillslope. As a result, pore water pressures, volumetric water content, effective stress, and thus the propensity for landsliding vary over seasonal and shorter time scales. We apply a general framework for assessing the stability of infinite slopes under transient variably saturated conditions. The framework includes profiles of pressure head and volumetric water content combined with a general effective stress for slope stability analysis. The general effective stress, or suction stress, provides a means for rigorous quantification of stress changes due to rainfall and infiltration and thus the analysis of slope stability over the range of volumetric water contents and pressure heads relevant to shallow landslide initiation. We present results using an analytical solution for transient infiltration for a range of soil texture and hydrological properties typical of landslide-prone hillslopes and show the effect of these properties on the timing and depth of slope failure. We follow by analyzing field-monitoring data acquired prior to shallow landslide failure of a hillside near Seattle, Washington, and show that the timing of the slide was predictable using measured pressure head and volumetric water content and show how the approach can be used in a forward manner using a numerical model for transient infiltration.

Controls on the variability of net infiltration to desert sandstone

USGS Publications Warehouse

Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

2007-01-01

As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

Correlation of Water Quality Parameters with Metal Concentrations in Permeable Pavement Infiltrate

EPA Science Inventory

EPA constructed a 4,000-m2 parking lot for research and demonstration of three permeable pavements [permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA)] at the Edison Environmental Center in Edison, NJ in 2009. Infiltrate samples from e...

PROSPECTS FOR ENHANCED GROUNDWATER RECHARGE VIA INFILTRATION OF URBAN STORMWATER RUNOFF: A CASE STUDY

EPA Science Inventory

The rain garden is an urban storm water best management practice that is used to infiltrate runoff close to its source, thereby disconnecting impervious area while providing an avenue for groundwater recharge. Groundwater recharge may provide additional benefits to aquatic ecosys...

Comparison of algorithms and parameterisations for infiltration into organic-covered permafrost soils

USDA-ARS?s Scientific Manuscript database

Infiltration into frozen and unfrozen soils is critical in hydrology, controlling active layer soil water dynamics and influencing runoff. Few Land Surface Models (LSMs) and Hydrological Models (HMs) have been developed, adapted or tested for frozen conditions and permafrost soils. Considering the v...

Soil management and green water in sloping rainfed vineyards

NASA Astrophysics Data System (ADS)

José Marqués Pérez, María; Ruíz-Colmenero, Marta; García-Díaz, Andrés; Bienes Allas, Ramón

2017-04-01

Improved crop production in areas with restricted water availability is of particular interest. Farmers need to maximize the water use efficiency when the possibilities of further extension of irrigation are limited and water is becoming scarce and expensive. Water in rainfed crops depends on rainfall depth and soil characteristics such as texture and structure, water holding capacity, previous moisture, infiltration, soil surface conditions, steepness and slope length. Land management practices can be used to maximise water availability. In previous studies the unwillingness of farmers to change their practices towards more sustainable use was mainly due to the worry about water competition. This work is aimed at understanding the influence of management practices in the water partitioning of this land use. This study was conducted in a sloping vineyard in the centre of Spain. A rain gauge recorded rainfall depth and intensity in the area. Three different soil management practices were considered: 1) traditional tillage, 2) permanent cover and 3) mowed cover of cereals, both sown in the strips between vines. Two moisture sensors were buried at 10 and 35 cm depths. Three replicates per management practice were performed. It is expected that the lack of tillage increase the potential for litter to protect the soil surface against raindrop impact and to contribute to increasing soil organic carbon, and the corresponding increase in infiltration and water holding capacity. The analysis of two years of daily records of rainfall, runoff and soil moisture are intended to establish any influence of management practices on the partitioning of water. Particularly, the so-called "green water" was estimated, i.e. the fraction of rainfall that infiltrates into the soil and will be further available to plants. Soil characteristics such as texture, structure, moisture, infiltration were established. In addition simulated rainfalls carried out in summer and winter over bounded plots having different management practices allowed the record of runoff per minute and further influence in soil moisture. After rainfalls soils were at field capacity and progressively dried in undisturbed conditions. Particle size analysis shows that this soil has 58 % sand, 18% silt and 24% clay, corresponding to a Sandy Clay Loam texture. Total porosity in the topsoil ranges from 49 to 51%, although according to previous studies only the 28% is effective to stock water in their micro and mesopores. In the upper 35 cm these soils are able to store from 0.05 to 0.25 m3 of water per m3 of soil depending on the seasons. At the same time, variations of runoff / infiltration were also noticed depending on the seasons and treatments.

An assessment of the BEST procedure to estimate the soil water retention curve

NASA Astrophysics Data System (ADS)

Castellini, Mirko; Di Prima, Simone; Iovino, Massimo

2017-04-01

The Beerkan Estimation of Soil Transfer parameters (BEST) procedure represents a very attractive method to accurately and quickly obtain a complete hydraulic characterization of the soil (Lassabatère et al., 2006). However, further investigations are needed to check the prediction reliability of soil water retention curve (Castellini et al., 2016). Four soils with different physical properties (texture, bulk density, porosity and stoniness) were considered in this investigation. Sites of measurement were located at Palermo University (PAL site) and Villabate (VIL site) in Sicily, Arborea (ARB site) in Sardinia and in Foggia (FOG site), Apulia. For a given site, BEST procedure was applied and the water retention curve was estimated using the available BEST-algorithms (i.e., slope, intercept and steady), and the reference values of the infiltration constants (β=0.6 and γ=0.75) were considered. The water retention curves estimated by BEST were then compared with those obtained in laboratory by the evaporation method (Wind, 1968). About ten experiments were carried out with both methods. A sensitivity analysis of the constants β and γ within their feasible range of variability (0.1<β<1.9 and of 0.61<γ< 0.79) was also carried out for each soil in order to establish: i) the impact of infiltration constants in the three BEST-algorithms on saturated hydraulic conductivity, Ks, soil sorptivity, S and on the retention curve scale parameter, hg; ii) the effectiveness of the three BEST-algorithms in the estimate of the soil water retention curve. Main results of sensitivity analysis showed that S tended to increase for increasing β values and decreasing values of γ for all the BEST-algorithms and soils. On the other hand, Ks tended to decrease for increasing β and γ values. Our results also reveal that: i) BEST-intercept and BEST-steady algorithms yield lower S and higher Ks values than BEST-slope; ii) these algorithms yield also more variable values. For the latter, a higher sensitiveness of these two alternative algorithms to β than for γ was established. The decreasing sensitiveness to γ may lead to a possible lack in the correction of the simplified theoretical description of the parabolic two-dimensional and one-dimensional wetting front along the soil profile (Smettem et al., 1994). This likely resulted in lower S and higher Ks values. Nevertheless, these differences are expected to be negligible for practical applications (Di Prima et al., 2016). On the other hand, the -intercept and -steady algorithms yielded hg values independent from γ, hence, determining water retention curves by these algorithms appears questionable. The linear regression between the soil water retention curves of BEST-slope and BEST-intercept (note that the same result is obtained with BEST-steady, due to a purely analytical reason) vs. lab method showed the following main results: i) the BEST procedure generally tends to underestimate the soil water retention (the exception was the PAL site); depending on the soil and algorithmic, the root mean square differences, RMSD obtained with BEST and lab method ranged between 0.028 cm3/cm3 (VIL, BEST-slope) and 0.082 cm3/cm3(FOG, BEST-intercept/steady); highest RMSD values (0.124-0.140 cm3/cm3) were obtained in the PAL site; ii) depending on the soil, BEST-slope generally determined lowest RMSD values (by a factor of 1.2-2.1); iii) when the whole variability range of β and γ was considered and a different couple of parameters was chosen (in general, extreme values of the parameters), lower RMSD values were detected in three out of four cases for BEST-slope; iv) the negligible observed differences of RMSD however suggest that using the reference values of infiltration constants, does not worsen significantly the soil water retention curve estimation; v) in 25% of considered soils (PAL site), the BEST procedure was not able to reproduce the retention curve of the soil in a sufficiently accurate way. In conclusion, our results showed that the BEST-slope algorithm appeared to yield more accurate estimates of water retention data with reference to three of the four sampled soils. Conversely, determining water retention curves by the -intercept and -steady algorithms may be questionable, since these algorithms overestimated hg yielding independent values of this parameter from the proportionality coefficient γ. (*) The work was supported by the project "STRATEGA, Sperimentazione e TRAsferimento di TEcniche innovative di aGricoltura conservativA", financed by Regione Puglia - Servizio Agricoltura. References Castellini, M., Iovino, M., Pirastru, M., Niedda, M., Bagarello, V., 2016. Use of BEST Procedure to Assess Soil Physical Quality in the Baratz Lake Catchment (Sardinia, Italy). Soil Sci. Soc. Am. J. 80:742-755. doi:10.2136/sssaj2015.11.0389 Di Prima, S., Lassabatere, L., Bagarello, V., Iovino, M., Angulo-Jaramillo, R., 2016. Testing a new automated single ring infiltrometer for Beerkan infiltration experiments. Geoderma 262, 20-34. doi:10.1016/j.geoderma.2015.08.006 Lassabatère, L., Angulo-Jaramillo, R., Soria Ugalde, J.M., Cuenca, R., Braud, I., Haverkamp, R., 2006. Beerkan Estimation of Soil Transfer Parameters through Infiltration Experiments-BEST. Soil Sci. Soc. Am. J. 70:521-532. doi:10.2136/sssaj2005.0026 Smettem, K.R.J., Parlange, J.Y., Ross, P.J., Haverkamp, R., 1994. Three-dimensional analysis of infiltration from the disc infiltrometer: 1. A capillary-based theory. Water Resour. Res. 30, 2925-2929. doi:10.1029/94WR01787 Wind, G.P. 1968. Capillary conductivity data estimated by a simple method. In: Water in the Unsaturated Zone, Proceedings of Wageningen Syposium, June 1966 Vol.1 (eds P.E. Rijtema & H Wassink), pp. 181-191, IASAH, Gentbrugge, Belgium.

[Effects of different planting modes on the soil permeability of sloping farmlands in purple soil area].

PubMed

Li, Jian-Xing; He, Bing-Hui; Mei, Xue-Mei; Liang, Yan-Ling; Xiong, Jian

2013-03-01

Taking bare land as the control, this paper studied the effects of different planting modes on the soil permeability of sloping farmlands in purple soil area. For the test six planting modes, the soil permeability was in the order of Eriobotrya japonica > Citrus limon > Vetiveria zizanioides hedgerows +corn >Leucaena leucocephala hedgerows + corn> Hemerocallis fulva > corn> bare land, and decreased with increasing depth. The eigenvalues of soil infiltration were in the order of initial infiltration rate> average infiltration rate> stable infiltration rate. The soil permeability had significant positive linear correlations with soil total porosity, non-capillary porosity, initial moisture content, water holding capacity, and organic matter content, and significant negative linear correlation with soil bulk density. The common empirical infiltration model could well fit the soil moisture infiltration processes under the six planting modes, while the Kostiakov equation could not.

Temperature peaks affect fire-induced soil water repellency, infiltration and erosion risk of Mediterranean shrublands. Implications for water and sediment connectivity

NASA Astrophysics Data System (ADS)

Jordán, Antonio; Zavala, Lorena M.; Gordillo-Rivero, Ángel J.; Miriam, Miriam; Keesstra, Saskia; Cerdà, Artemi

2017-04-01

We know that the impact of fire on soil water repellency varies largely with the availability of water and physical and chemical soil properties, as well as the intensity of pre-existing hydrophobicity. However, there are few studies that relate the intensity of post-fire soil hydrophobicity and its persistence to the intensity and duration of thermal peaks occurring during fire. Fundamentally, this is due to the difficulty of quantifying these factors in situ, so that experimental fires are an extremely useful tool. The objective of this work was to study the impact of the intensity and duration of the thermal peaks observed during an experimental fire in the hydrophobicity of previously wet or slightly hydrophobic soils and the consequences of these changes on infiltration, runoff and soil loss (through rainfall simulation) in the immediate (30 days) and medium-term (1 year) post-fire period. In general, soil water repellency increased in all cases, although high temperatures and residence times of moderate thermal peaks caused the greatest impact. Although infiltration rates determined by mini-disk infiltrometer with water generally declined, no significant changes were observed in the same measurement with ethanol (which negates the effect of hydrophobicity).

Stable isotopes of water as a natural tracer for infiltration into urban sewer systems

NASA Astrophysics Data System (ADS)

Kracht, O.; Gresch, M.; de Bénédittis, J.; Prigiobbe, V.; Gujer, W.

2003-04-01

An adequate understanding of the hydraulic interaction between leaky sewers and groundwater is essential for the sustainable management of both sewer systems and aquifers in urbanized areas. Undesirable infiltration of groundwater into sewers can contribute over 50% of the total discharge and is detrimental to treatment plant efficiency. On the other hand, in many European cities groundwater surface levels seem to be particularly controlled by the drainage effect of permeable sewer systems. However, nowadays methods for the quantification of these exchange processes are still subject to considerable uncertainties due to their underlying assumptions. The frequently used assumption that the night time minimum in the diurnal wastewater hydrograph is equal to the "parasitic discharge" has to be reconsidered to today's patterns of human life as well as to the long residence time of wastewater in the sewer networks of modern cities. The suitability of stable water isotopes as a natural tracer to differentiate the origin of water in the sewer ("real" wastewater or infiltrating groundwater) is currently investigated in three different catchment areas. The studies are carried out within the framework of the European research project APUSS (Assessing Infiltration and Exfiltration on the Performance of Urban Sewer Systems): 1) The village of Rümlang (Zürich, Switzerland) is predominantly served with drinking water from the Lake Zürich. A large fraction of the lakes water is derived from precipitation in the Alps. This drinking water represents the intrinsic provenience of the wastewater with an δ18O value around -11,5 per mill and δ^2H value around -82 per mill vs. SMOW. In contrast, the local groundwater is originating from precipitation in a moderate altitude of about 450 m above sea level and shows comparatively enriched mean δ18O values of -9,7 per mill and δ^2H values of -70 per mill with only small natural variations. The isotopic separation between these endmembers is basically sufficient to estimate the ratio of infiltrating water in the sewer. Uncertainties yet derive from varying amounts of local groundwater in the water supply mains. These will be substituted by additionally purchased lake water in the next experimental stage. 2) The experimental site Toraccia (suburb of Rome, Italy) obtains drinking water from the Peschiera springs group that is situated in the central Apennines chain about 90 km north east of Rome. This spring water is transported to Rome by an aqueduct. A first campaign revealed an average mains water δ18O value of -8,4 per mill and δ^2H value of -53 per mill. Potential sources of infiltration are occurrences of perched groundwater. These appear to be enriched compared to the drinking water about 2 to 3 per mill in the δ18O and 10 to 20 per mill in the δ^2H value, but show disadvantageous strong variations. 3) Investigations in the urban area of Lyon (France) benefit from the isotopic differences between underground waters originating from the two rivers Rhone and Saone and their associated alluvial aquifers. The oxygen isotope composition of the Rhone water is roughly 3 per mill lighter than that of the river Saone, due to the large differences in the mean altitude and topographic situation of their catchment basins. Considerable amounts of mains water are extracted by production wells in the Rhone aquifer. In consequence a usable difference in the oxygen isotope composition between wastewater and local groundwater of about 1.5 per mill is available for application studies in certain parts of the city.

Biological soil crust succession impact on soil moisture and temperature in the sub-surface along a rainfall gradient

NASA Astrophysics Data System (ADS)

Zaady, E.; Yizhaq, H.; Ashkenazy, Y.

2012-04-01

Biological soil crusts produce mucilage sheets of polysaccharides that cover the soil surface. This hydrophobic coating can seal the soil micro-pores and thus cause reduction of water permeability and may influence soil temperature. This study evaluates the impact of crust composition on sub-surface water and temperature over time. We hypothesized that the successional stages of biological soil crusts, affect soil moisture and temperature differently along a rainfall gradient throughout the year. Four experimental sites were established along a rainfall gradient in the western Negev Desert. At each site three treatments; crust removal, pure sand (moving dune) and natural crusted were monitored. Crust successional stage was measured by biophysiological and physical measurements, soil water permeability by field mini-Infiltrometer, soil moisture by neutron scattering probe and temperature by sensors, at different depths. Our main interim conclusions from the ongoing study along the rainfall gradient are: 1. the biogenic crust controls water infiltration into the soil in sand dunes, 2. infiltration was dependent on the composition of the biogenic crust. It was low for higher successional stage crusts composed of lichens and mosses and high with cyanobacterial crust. Thus, infiltration rate controlled by the crust is inverse to the rainfall gradient. Continuous disturbances to the crust increase infiltration rates, 3. despite the different rainfall amounts at the sites, soil moisture content below 50 cm is almost the same. We therefore predict that climate change in areas that are becoming dryer (desertification) will have a positive effect on soil water content and vice versa.