Impact of freeway weaving segment design on light-duty vehicle exhaust emissions.

PubMed

Li, Qing; Qiao, Fengxiang; Yu, Lei; Chen, Shuyan; Li, Tiezhu

2018-06-01

In the United States, 26% of greenhouse gas emissions is emitted from the transportation sector; these emisssions meanwhile are accompanied by enormous toxic emissions to humans, such as carbon monoxide (CO), nitrogen oxides (NO x ), and hydrocarbon (HC), approximately 2.5% and 2.44% of a total exhaust emissions for a petrol and a diesel engine, respectively. These exhaust emissions are typically subject to vehicles' intermittent operations, such as hard acceleration and hard braking. In practice, drivers are inclined to operate intermittently while driving through a weaving segment, due to complex vehicle maneuvering for weaving. As a result, the exhaust emissions within a weaving segment ought to vary from those on a basic segment. However, existing emission models usually rely on vehicle operation information, and compute a generalized emission result, regardless of road configuration. This research proposes to explore the impacts of weaving segment configuration on vehicle emissions, identify important predictors for emission estimations, and develop a nonlinear normalized emission factor (NEF) model for weaving segments. An on-board emission test was conducted on 12 subjects on State Highway 288 in Houston, Texas. Vehicles' activity information, road conditions, and real-time exhaust emissions were collected by on-board diagnosis (OBD), a smartphone-based roughness app, and a portable emission measurement system (PEMS), respectively. Five feature selection algorithms were used to identify the important predictors for the response of NEF and the modeling algorithm. The predictive power of four algorithm-based emission models was tested by 10-fold cross-validation. Results showed that emissions are also susceptible to the type and length of a weaving segment. Bagged decision tree algorithm was chosen to develop a 50-grown-tree NEF model, which provided a validation error of 0.0051. The estimated NEFs are highly correlated with the observed NEFs in the training data set as well as in the validation data set, with the R values of 0.91 and 0.90, respectively. Existing emission models usually rely on vehicle operation information to compute a generalized emission result, regardless of road configuration. In practice, while driving through a weaving segment, drivers are inclined to perform erratic maneuvers, such as hard braking and hard acceleration due to the complex weaving maneuver required. As a result, the exhaust emissions within a weaving segment vary from those on a basic segment. This research proposes to involve road configuration, in terms of the type and length of a weaving segment, in constructing an emission nonlinear model, which significantly improves emission estimations at a microscopic level.

Flow-Tube Reactor Experiments on the High Temperature Oxidation of Carbon Weaves

NASA Technical Reports Server (NTRS)

Panerai, Francesco; White, Jason D.; Robertson, Robert; Borner, Arnaud; Ferguson, Joseph C.; Mansour, Nagi N.

2017-01-01

Under entry conditions carbon weaves used in thermal protection systems (TPS) decompose via oxidation. Modeling this phenomenon is challenging due to the different regimes encountered along a flight trajectory. Approaches using equilibrium chemistry may lead to over-estimated mass loss and recession at certain conditions. Concurrently, there is a shortcoming of experimental data on carbon weaves to enable development of improved models. In this work, a flow-tube test facility was used to measure the oxidation of carbon weaves at temperatures up to 1500 K. The material tested was the 3D carbon weave used for the heat shield of the NASA Adaptive Deployable Entry and Placement Technology, ADEPT. Oxidation was characterized by quantifying decomposition gases (CO and CO2), by mass measurements, and by microscale surface analysis. The current set of measurements contributes to the development of finite rate chemistry models for carbon fabrics used in woven TPS materials.

The Effect of Various Weave Designs on Mechanical Behavior of Lamina Intraply Composite Made from Kenaf Fiber Yarn

NASA Astrophysics Data System (ADS)

Yuhazri, M. Y.; Amirhafizan, M. H.; Abdullah, A.; Sihombing, H.; Saarah, A. B.; Fadzol, O. M.

2016-11-01

The development of lamina intraply composite is a novel approach that can be adopted to address the challenges of balance mechanical properties of polymer composite. This research will focuses on the effects of weave designs on the mechanical behavior of a single ply or also known as lamina intraply composite. The six (6) specimens of lamina intraply composites were made by kenaf fiber as a reinforcement and unsaturated polyester resin as a matrix in various weave designs which were plain, twill, satin, basket, mock leno and leno weave. The vacuum infusion technique was adopted due to advantages over hand lay-up. It was found that the plain, twill and satin weave exhibited better mechanical properties on tensile strength. The fiber content of the specimen was 40% and the result of the resin content of the specimen was 60% due to the higher permeability of natural fiber.

4. VIEW WEST FROM DOOR OF NORTHERN ROOM OF WEAVING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. VIEW WEST FROM DOOR OF NORTHERN ROOM OF WEAVING HOUSE, SHOWING FIREPLACE AND REMAINS OF COTTON GIN (The gin is thought to have been made locally in the 19th century by William Ellison, a free black carpenter and enterpreneur; see data pages.) - Borough House, Weaving House, State Route 261 & Garners Ferry Road, Stateburg, Sumter County, SC

Angle-Ply Weaving

NASA Technical Reports Server (NTRS)

Farley, Gary L.

1990-01-01

Bias-direction or angle-ply weaving is proposed new process for weaving fibers along bias in conventional planar fabric or in complicated three-dimensional multilayer fabric preform of fiber-reinforced composite structure. Based upon movement of racks of needles and corresponding angle yarns across fabric as fabric being formed. Fibers woven along bias increases shear stiffness and shear strength of preform, increasing value of preform as structural member.

Cancer incidence among women flax textile manufacturing workers in Lithuania.

PubMed

Kuzmickiene, Irena; Stukonis, Mecys

2010-07-01

To determine site-specific cancer incidence among women spinning-weaving and dyeing-finishing workers in the largest flax textile factory in Lithuania. The cancer incidence of a cohort of 3447 women workers from a flax textile factory was investigated for the period 1978-2002. All subjects were employed at the plant in the period 1957-2000 for a minimum of 12 months. Standardised incidence ratios (SIRs) were estimated by use of the corresponding national rates. SIRs were calculated for the spinning-weaving and dyeing-finishing work categories, and for two durations of employment categories (<10 years, > or =10 years). The cancer SIRs among spinning-weaving and dyeing-finishing workers were 0.84 (95% CI 0.69 to 1.00) and 0.90 (95% CI 0.52 to 1.44). An incidence deficit for non-melanoma skin cancer was found for the spinning-weaving unit (SIR 0.45, 95% CI 0.18 to 0.92). The risk of oral cavity and pharynx cancer was significantly increased in spinning-weaving unit workers with <10 years of employment (SIR 5.71, 95% CI 1.56 to 14.60). A significant excess of thyroid cancer and nervous system cancer was found among dyeing-finishing workers. The overall cancer and non-melanoma skin cancer incidence rate among flax spinning-weaving workers was lower compared with the Lithuanian population. The present findings lend some support to an excess of thyroid and nervous system cancers among dyeing-finishing workers and of oral cavity and pharynx cancer in spinning-weaving workers.

25 CFR 309.13 - What are examples of other weaving and textiles that are Indian products?

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 2 2011-04-01 2011-04-01 false What are examples of other weaving and textiles that are Indian products? 309.13 Section 309.13 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR PROTECTION OF INDIAN ARTS AND CRAFTS PRODUCTS § 309.13 What are examples of other weaving and textiles that...

25 CFR 309.13 - What are examples of other weaving and textiles that are Indian products?

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false What are examples of other weaving and textiles that are Indian products? 309.13 Section 309.13 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR PROTECTION OF INDIAN ARTS AND CRAFTS PRODUCTS § 309.13 What are examples of other weaving and textiles that...

A triaxial supramolecular weave

NASA Astrophysics Data System (ADS)

Lewandowska, Urszula; Zajaczkowski, Wojciech; Corra, Stefano; Tanabe, Junki; Borrmann, Ruediger; Benetti, Edmondo M.; Stappert, Sebastian; Watanabe, Kohei; Ochs, Nellie A. K.; Schaeublin, Robin; Li, Chen; Yashima, Eiji; Pisula, Wojciech; Müllen, Klaus; Wennemers, Helma

2017-11-01

Despite recent advances in the synthesis of increasingly complex topologies at the molecular level, nano- and microscopic weaves have remained difficult to achieve. Only a few diaxial molecular weaves exist—these were achieved by templation with metals. Here, we present an extended triaxial supramolecular weave that consists of self-assembled organic threads. Each thread is formed by the self-assembly of a building block comprising a rigid oligoproline segment with two perylene-monoimide chromophores spaced at 18 Å. Upon π stacking of the chromophores, threads form that feature alternating up- and down-facing voids at regular distances. These voids accommodate incoming building blocks and establish crossing points through CH-π interactions on further assembly of the threads into a triaxial woven superstructure. The resulting micrometre-scale supramolecular weave proved to be more robust than non-woven self-assemblies of the same building block. The uniform hexagonal pores of the interwoven network were able to host iridium nanoparticles, which may be of interest for practical applications.

Risky driving behaviors in Tehran, Iran.

PubMed

Shams, Mohsen; Rahimi-Movaghar, Vafa

2009-03-01

Iran has one of the highest fatality rates due to road traffic crashes (RTC) in the world. The disability adjusted life years (DALYs) for RTC in Iran is more than 1,300,000 years, which is more than that for any other disease such as cardiovascular or cancer. We evaluated risky driving behaviors in Tehran, the capital of Iran. A retrospective analysis was conducted based on the data obtained from the Tehran Police Safety Driving Department. Offenses and crashes were studied in different municipal districts in Tehran from March 2006 to March 2007. The inclusion criteria were risky driving behaviors fined by the police. Nonbehavioral offences were excluded. There were 3,821,798 offenses in Tehran. Not wearing a seat belt was the most common (59%) example of risky driving behavior, followed by tailgating, not wearing motorcycle helmets, talking on the cell phone while driving, overtaking from the wrong side, speeding, not driving between the lanes, weaving in and out of traffic, left deviation, and changing lanes without signals. The most common causes of RTC in Tehran are speeding, overtaking from the wrong side, and the rapid changing of driving lanes. The study factors effective in preventing risky driving behaviors in Tehran is recommended. The consideration of specific characteristics of the municipal districts is necessary to reduce risky driving behaviors.

PEDOT:PSS-Based Piezo-Resistive Sensors Applied to Reinforcement Glass Fibres for in Situ Measurement during the Composite Material Weaving Process

PubMed Central

Trifigny, Nicolas; Kelly, Fern M.; Cochrane, Cédric; Boussu, François; Koncar, Vladan; Soulat, Damien

2013-01-01

The quality of fibrous reinforcements used in composite materials can be monitored during the weaving process. Fibrous sensors previously developed in our laboratory, based on PEDOT:PSS, have been adapted so as to directly measure the mechanical stress on fabrics under static or dynamic conditions. The objective of our research has been to develop new sensor yarns, with the ability to locally detect mechanical stresses all along the warp or weft yarn. This local detection is undertaken inside the weaving loom in real time during the weaving process. Suitable electronic devices have been designed in order to record in situ measurements delivered by this new fibrous sensor yarn. PMID:23959238

A pooled analysis of on-the-road highway driving studies in actual traffic measuring standard deviation of lateral position (i.e., "weaving") while driving at a blood alcohol concentration of 0.5 g/L.

PubMed

Jongen, S; Vermeeren, A; van der Sluiszen, N N J J M; Schumacher, M B; Theunissen, E L; Kuypers, K P C; Vuurman, E F P M; Ramaekers, J G

2017-03-01

The on-the-road highway driving test is generally regarded as a gold standard for assessing drug-induced driving impairment. The primary outcome measure is the standard deviation of lateral position (SDLP), a measure of road tracking error or "weaving". The test has been calibrated for incremental doses of alcohol almost 30 years ago in order to define the impact of drug-induced impairment in terms of blood alcohol concentration (BAC) equivalents. Drug-induced changes in SDLP exceeding 2.4 cm have been evaluated as clinically relevant ever since. The present analysis was conducted to assess the robustness of the alcohol effect in a range of on-the-road driving studies which have been conducted since the initial alcohol calibration study. The present study pooled data of 182 participants from nine placebo-controlled crossover studies who performed the highway driving test, while their BAC was at or just below the legal limit for drivers (i.e., 0.5 g/L). Overall, mean SDLP increased with 2.5 cm (95% CI 2.0-2.9 cm). Equivalence testing showed that the clinical relevance criterion value of 2.4 cm fell well within the 95% CI in each individual study. Gender did not affect alcohol-induced changes in SDLP. These results demonstrate the robustness and validity of the clinical relevance criterion for SDLP as measured during on-the-road driving.

Weaving and neural complexity in symmetric quantum states

NASA Astrophysics Data System (ADS)

Susa, Cristian E.; Girolami, Davide

2018-04-01

We study the behaviour of two different measures of the complexity of multipartite correlation patterns, weaving and neural complexity, for symmetric quantum states. Weaving is the weighted sum of genuine multipartite correlations of any order, where the weights are proportional to the correlation order. The neural complexity, originally introduced to characterize correlation patterns in classical neural networks, is here extended to the quantum scenario. We derive closed formulas of the two quantities for GHZ states mixed with white noise.

American Society of Composites, 32nd Technical Conference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aitharaju, Venkat; Wollschlager, Jeffrey; Plakomytis2, Dimitrios

This paper will present a general methodology by which weave draping manufacturing simulation results can be utilized to include the effects of weave draping and scissor angle in a structural multiscale simulation. While the methodology developed is general in nature, this paper will specifically demonstrate the methodology applied to a truncated pyramid, utilizing manufacturing simulation weave draping results from ESI PAM-FORM, and multiscale simulation using Altair Multiscale Designer (MDS) and OptiStruct. From a multiscale simulation perspective, the weave draping manufacturing simulation results will be used to develop a series of woven unit cells which cover the range of weave scissormore » angles existing within the part. For each unit cell, a multiscale material model will be developed, and applied to the corresponding spatial locations within the structural simulation mesh. In addition, the principal material orientation will be mapped from the wave draping manufacturing simulation mesh to the structural simulation mesh using Altair HyperMesh mapping technology. Results of the coupled simulation will be compared and verified against experimental data of the same available via General Motors (GM) Department of Energy (DOE) project.« less

Towards integrated modelling: full image simulations for WEAVE

NASA Astrophysics Data System (ADS)

Dalton, Gavin; Ham, Sun Jeong; Trager, Scott; Abrams, Don Carlos; Bonifacio, Piercarlo; Aguerri, J. A. L.; Middleton, Kevin; Benn, Chris; Rogers, Kevin; Stuik, Remko; Carrasco, Esperanza; Vallenari, Antonella; Jin, Shoko; Lewis, Jim

2016-08-01

We present an integrated end-end simulation of the spectral images that will be obtained by the weave spectrograph, which aims to include full modelling of all effects from the top of the atmosphere to the detector. These data are based in input spectra from a combination of library spectra and synthetic models, and will be used to provide inputs for an endend test of the full weave data pipeline and archive systems, prior to 1st light of the instrument.

Weaving and neural complexity in symmetric quantum states

DOE PAGES

Susa, Cristian E.; Girolami, Davide

2017-12-27

Here, we study the behaviour of two different measures of the complexity of multipartite correlation patterns, weaving and neural complexity, for symmetric quantum states. Weaving is the weighted sum of genuine multipartite correlations of any order, where the weights are proportional to the correlation order. The neural complexity, originally introduced to characterize correlation patterns in classical neural networks, is here extended to the quantum scenario. We derive closed formulas of the two quantities for GHZ states mixed with white noise.

Weaving and neural complexity in symmetric quantum states

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susa, Cristian E.; Girolami, Davide

Here, we study the behaviour of two different measures of the complexity of multipartite correlation patterns, weaving and neural complexity, for symmetric quantum states. Weaving is the weighted sum of genuine multipartite correlations of any order, where the weights are proportional to the correlation order. The neural complexity, originally introduced to characterize correlation patterns in classical neural networks, is here extended to the quantum scenario. We derive closed formulas of the two quantities for GHZ states mixed with white noise.

Musculoskeletal problems in Iranian hand-woven carpet industry: guidelines for workstation design.

PubMed

Choobineh, Alireza; Hosseini, Mostafa; Lahmi, Mohammadali; Khani Jazani, Reza; Shahnavaz, Houshang

2007-09-01

Long hours of static work with awkward posture at traditionally designed looms can cause high prevalence of musculoskeletal disorders (MSDs) among carpet weavers. A comprehensive study was conducted in this industry with the objectives of determination of MSDs symptoms prevalence; identification of major factors associated with MSDs symptoms in carpet weaving occupation; and development of guidelines for weaving workstation design. In the present paper, this ergonomics study is presented. The study consisted of two phases. In the first phase, MSDs symptoms in nine Iranian provinces were surveyed by questionnaire among 1439 randomly selected weavers. Working posture and weaving workstations were ergonomically assessed as well. The results of this phase revealed that symptoms from the musculoskeletal system occurred in high rate among weavers with the prevalence significantly higher than that of the general Iranian population (P<0.001). It was found that the majority of ergonomics shortcomings originated from ill-designed weaving workstation. Based on the findings, some general guidelines for workstation design were presented. In the second phase, considering the general guidelines, an adjustable workstation was designed and constructed. To develop quantitative guidelines for optimizing workstation set-up, in the laboratory, nine sets of experimental conditions were tested, and working posture and weavers' perceptions were measured. The results of this lab work showed that working posture was acceptable for both the researchers and the weavers when the weaving height was adjusted 20 cm above the elbow height and a high seat with forward slope was used. By combining the results of the two phases, guidelines for weaving workstation design were presented. In this ergonomics-oriented workstation, loom is vertical. Seat, loom and weaving heights are adjustable. There is enough leg room under the loom. The seat with 10 degrees forward slope is adjusted 15 cm above the popliteal height of the weaver. Weaving height is set at 20 cm above the elbow height. It is believed that the recommended workstation improves working posture and results in reduced postural stress on weavers' bodies and, consequently, reduced prevalence of MSDs symptoms.

Prediction of progressive damage and strength of plain weave composites using the finite element method

NASA Astrophysics Data System (ADS)

Srirengan, Kanthikannan

The overall objective of this research was to develop the finite element code required to efficiently predict the strength of plain weave composite structures. Towards which, three-dimensional conventional progressive damage analysis was implemented to predict the strength of plain weave composites subjected to periodic boundary conditions. Also, modal technique for three-dimensional global/local stress analysis was developed to predict the failure initiation in plain weave composite structures. The progressive damage analysis was used to study the effect of quadrature order, mesh refinement and degradation models on the predicted damage and strength of plain weave composites subjected to uniaxial tension in the warp tow direction. A 1/32sp{nd} part of the representative volume element of a symmetrically stacked configuration was analyzed. The tow geometry was assumed to be sinusoidal. Graphite/Epoxy system was used. Maximum stress criteria and combined stress criteria were used to predict failure in the tows and maximum principal stress criterion was used to predict failure in the matrix. Degradation models based on logical reasoning, micromechanics idealization and experimental comparisons were used to calculate the effective material properties with of damage. Modified Newton-Raphson method was used to determine the incremental solution for each applied strain level. Using a refined mesh and the discount method based on experimental comparisons, the progressive damage and the strength of plain weave composites of waviness ratios 1/3 and 1/6 subjected to uniaxial tension in the warp direction have been characterized. Plain weave composites exhibit a brittle response in uniaxial tension. The strength decreases significantly with the increase in waviness ratio. Damage initiation and collapse were caused dominantly due to intra-tow cracking and inter-tow debonding respectively. The predicted strength of plain weave composites of racetrack geometry and waviness ratio 1/25.7 was compared with analytical predictions and experimental findings and was found to match well. To evaluate the performance of the modal technique, failure initiation in a short woven composite cantilevered plate subjected to end moment and transverse end load was predicted. The global/local predictions were found to reasonably match well with the conventional finite element predictions.

Investigation of Mechanical and Electromagnetic Interference Shielding Properties of Nickel-CFRP Textile Composites

NASA Astrophysics Data System (ADS)

Tugirumubano, Alexandre; Vijay, Santhiyagu Joseph; Go, Sun Ho; Kwac, Lee Ku; Kim, Hong Gun

2018-05-01

The most common materials used for electromagnetic interference shielding are metals and their alloys. However, those materials are heavy and highly reflective. In order to eliminate or reduce the intensity of wave radiation in their working environment, lightweight materials that have interference shielding properties are needed. In this paper, nickel wire mesh yarns (warps) were woven into carbon fibers-reinforced plastic yarns (wefts) to produce metal-carbon textile composite materials. The plain weave and 2/2 twill weave techniques were used, and the woven fabrics were laminated to manufacture experimental test samples. The nickel, which has high magnetic permeability and good electric conductivity, and carbon fibers, which have good electrical, thermal and mechanical properties, were used together to achieve the desired properties. The shielding effectiveness of each sample was investigated using a network analyzer connected with coaxial transmission line test in accordance with ASTM 4935-99 standard, with the frequencies ranging from 500 MHz to 1.5 GHz. Here, the plain weave structure showed higher shielding effectiveness than twill weave. The absorption losses for both materials were relatively greater than reflection losses. In reference to the orientation of wire mesh yarns about the loading axis, the tensile strengths in the transversal direction were 19.04 and 16.34% higher than the tensile strengths in longitudinal direction for plain weave and twill weave, respectively. The fractography analysis with SEM showed a ductile fracture of wire mesh and brittle fracture of epoxy matrix and carbon fibers.

Investigation of Mechanical and Electromagnetic Interference Shielding Properties of Nickel-CFRP Textile Composites

NASA Astrophysics Data System (ADS)

Tugirumubano, Alexandre; Vijay, Santhiyagu Joseph; Go, Sun Ho; Kwac, Lee Ku; Kim, Hong Gun

2018-04-01

The most common materials used for electromagnetic interference shielding are metals and their alloys. However, those materials are heavy and highly reflective. In order to eliminate or reduce the intensity of wave radiation in their working environment, lightweight materials that have interference shielding properties are needed. In this paper, nickel wire mesh yarns (warps) were woven into carbon fibers-reinforced plastic yarns (wefts) to produce metal-carbon textile composite materials. The plain weave and 2/2 twill weave techniques were used, and the woven fabrics were laminated to manufacture experimental test samples. The nickel, which has high magnetic permeability and good electric conductivity, and carbon fibers, which have good electrical, thermal and mechanical properties, were used together to achieve the desired properties. The shielding effectiveness of each sample was investigated using a network analyzer connected with coaxial transmission line test in accordance with ASTM 4935-99 standard, with the frequencies ranging from 500 MHz to 1.5 GHz. Here, the plain weave structure showed higher shielding effectiveness than twill weave. The absorption losses for both materials were relatively greater than reflection losses. In reference to the orientation of wire mesh yarns about the loading axis, the tensile strengths in the transversal direction were 19.04 and 16.34% higher than the tensile strengths in longitudinal direction for plain weave and twill weave, respectively. The fractography analysis with SEM showed a ductile fracture of wire mesh and brittle fracture of epoxy matrix and carbon fibers.

Weaving Arctic Networks of Support and Engaged Accountability

NASA Astrophysics Data System (ADS)

Warnick, W. K.

2003-12-01

This presentation will provide a preview of a new project which explores the potential of applying emerging educational research in conjunction with the latest polar research through a multifaceted approach designed to weave networks of support and engaged accountability between Arctic researchers, teachers, and learners. This presentation will outline how Sunwood's (2002) WoSEA educational model might be utilized to facilitate and study methods of engaging and supporting teachers and scientists in collaborative Arctic research and pedagogy. The model we are proposing employs action research methodology to provide educators and scientists the opportunity to engage in reflection on their own practice, and enhancement of their own practice through extensive connection and collaboration between education and scientific professionals, thus contributing to the cumulative development of a lifelong learning continuum. Our Weaving the Arctic project will amplify and enhance the voice, knowledge and expertise of Arctic researchers and teachers as each participant explores, shares, and showcases their experience, knowledge, and the products of their practice. Weaving thus holds great promise for addressing science education needs, particularly the critical needs surrounding enhancement and retention of STEM teachers in K-12 (especially rural) schools. This presentation will share the promise of our Weaving model.

The WEAVE-LOFAR Survey

NASA Astrophysics Data System (ADS)

Smith, D. J. B.; Best, P. N.; Duncan, K. J.; Hatch, N. A.; Jarvis, M. J.; Röttgering, H. J. A.; Simpson, C. J.; Stott, J. P.; Cochrane, R. K.; Coppin, K. E.; Dannerbauer, H.; Davis, T. A.; Geach, J. E.; Hale, C. L.; Hardcastle, M. J.; Hatfield, P. W.; Houghton, R. C. W.; Maddox, N.; McGee, S. L.; Morabito, L.; Nisbet, D.; Pandey-Pommier, M.; Prandoni, I.; Saxena, A.; Shimwell, T. W.; Tarr, M.; van Bemmel, I.; Verma, A.; White, G. J.; Williams, W. L.

2016-12-01

In these proceedings we highlight the primary scientific goals and design of the WEAVE-LOFAR survey, which will use the new WEAVE spectrograph on the 4.2m William Herschel Telescope to provide the primary source of spectroscopic information for the LOFAR Surveys Key Science Project. Beginning in 2018, WEAVE-LOFAR will generate more than 10^6 R=5000 365-960nm spectra of low-frequency selected radio sources, across three tiers designed to efficiently sample the redshift-luminosity plane, and produce a data set of enormous legacy value. The radio frequency selection, combined with the high multiplex and throughput of the WEAVE spectrograph, make obtaining redshifts in this way very efficient, and we expect that the redshift success rate will approach 100 per cent at z < 1. This unprecedented spectroscopic sample - which will be complemented by an integral field component - will be transformational in key areas, including studying the star formation history of the Universe, the role of accretion and AGN-driven feedback, properties of the epoch of reionisation, cosmology, cluster haloes and relics, as well as the nature of radio galaxies and protoclusters. Each topic will be addressed in unprecedented detail, and with the most reliable source classifications and redshift information in existence.

Safety performance for freeway weaving segments.

DOT National Transportation Integrated Search

2014-09-01

The intensive lane change maneuvers at weaving sections often result in safety and operational problems. : Various factors, including the design of ramp roadways, use of auxiliary lanes, and continuity of lanes will have : significant effects on the ...

Tailorable advanced blanket insulation using aluminoborosilicate and alumina batting

NASA Technical Reports Server (NTRS)

Calamito, Dominic P.

1989-01-01

Two types of Tailorable Advanced Blanket Insulation (TABI) flat panels for Advanced Space Transportation Systems were produced. Both types consisted of integrally woven, 3-D fluted core having parallel faces and connecting ribs of Nicalon yarns. The triangular cross section flutes of one type was filled with mandrels of processed Ultrafiber (aluminoborosilicate) stitchbonded Nextel 440 fibrous felt, and the second type wall filled with Saffil alumina fibrous felt insulation. Weaving problems were minimal. Insertion of the fragile insulation mandrels into the fabric flutes was improved by using a special insertion tool. An attempt was made to weave fluted core fabrics from Nextel 440 yarns but was unsuccessful because of the yarn's fragility. A small sample was eventually produced by an unorthodox weaving process and then filled with Saffil insulation. The procedures for setting up and weaving the fabrics and preparing and inserting insulation mandrels are discussed. Characterizations of the panels produced are also presented.

A comparative analysis of image features between weave embroidered Thangka and piles embroidered Thangka

NASA Astrophysics Data System (ADS)

Li, Zhenjiang; Wang, Weilan

2018-04-01

Thangka is a treasure of Tibetan culture. In its digital protection, most of the current research focuses on the content of Thangka images, not the fabrication process. For silk embroidered Thangka of "Guo Tang", there are two craft methods, namely, weave embroidered and piles embroidered. The local texture of weave embroidered Thangka is rough, and that of piles embroidered Thangka is more smooth. In order to distinguish these two kinds of fabrication processes from images, a effectively segmentation algorithm of color blocks is designed firstly, and the obtained color blocks contain the local texture patterns of Thangka image; Secondly, the local texture features of the color block are extracted and screened; Finally, the selected features are analyzed experimentally. The experimental analysis shows that the proposed features can well reflect the difference between methods of weave embroidered and piles embroidered.

The meaning and value of traditional occupational practice: a Karen woman's story of weaving in the United States.

PubMed

Smith, Yda J; Stephenson, Stephanie; Gibson-Satterthwaite, Michelle

2013-01-01

This case study sought to understand the meaning of restoring traditional weaving as an occupation among Karen women from Burma who now live in an urban city in the United States and to examine the impact of weaving on their daily lives in terms of identity, empowerment, social support, and opportunities for entrepreneurship. The story of one Karen woman, Paw Law Eh, is described. Her story exemplifies the negative consequences of restricted access to familiar and meaningful daily activities, or "occupations", the relationship between occupation and self-identity, how participation in valued occupations can enhance social networks, and the restorative effects that are possible when engagement in meaningful occupations are maintained or restored. Her story demonstrates that occupational therapists have the skills and opportunity to contribute significantly to the well-being of Karen women by supporting the restoration of the occupation of weaving.

Anomalous Stretchable Conductivity Using an Engineered Tricot Weave.

PubMed

Lee, Yong-Hee; Kim, Yoonseob; Lee, Tae-Ik; Lee, Inhwa; Shin, Jaeho; Lee, Hyun Soo; Kim, Taek-Soo; Choi, Jang Wook

2015-12-22

Robust electric conduction under stretching motions is a key element in upcoming wearable electronic devices but is fundamentally very difficult to achieve because percolation pathways in conductive media are subject to collapse upon stretching. Here, we report that this fundamental challenge can be overcome by using a parameter uniquely available in textiles, namely a weaving structure. A textile structure alternately interwoven with inelastic and elastic yarns, achieved via a tricot weave, possesses excellent elasticity (strain up to 200%) in diagonal directions. When this textile is coated with conductive nanomaterials, proper textile engineering allows the textile to obtain an unprecedented 7-fold conductivity increase, with conductivity reaching 33,000 S cm(-1), even at 130% strain, due to enhanced interyarn contacts. The observed stretching conductivity can be described well using a modified 3D percolation theory that reflects the weaving effect and is also utilized for stretchable electronic interconnects and supercapacitors with high performance.

Cognitive dimensions of talim: evaluating weaving notation through cognitive dimensions (CDs) framework.

PubMed

Kaur, Gagan Deep

2017-05-01

The design process in Kashmiri carpet weaving is distributed over a number of actors and artifacts and is mediated by a weaving notation called talim. The script encodes entire design in practice-specific symbols. This encoded script is decoded and interpreted via design-specific conventions by weavers to weave the design embedded in it. The cognitive properties of this notational system are described in the paper employing cognitive dimensions (CDs) framework of Green (People and computers, Cambridge University Press, Cambridge, 1989) and Blackwell et al. (Cognitive technology: instruments of mind-CT 2001, LNAI 2117, Springer, Berlin, 2001). After introduction to the practice, the design process is described in 'The design process' section which includes coding and decoding of talim. In 'Cognitive dimensions of talim' section, after briefly discussing CDs framework, the specific cognitive dimensions possessed by talim are described in detail.

78 FR 18314 - Foreign-Trade Zone 169-Manatee County, Florida; Application for Production Authority; ASO, LLC...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-26

... of the finished product) include the following: 100% polyester, 100% cotton dyed plain weave, and 62% cotton/38% polyester plain weave (duty rates range from 7 to 12%). In accordance with the Board's...

Snakes in the Grass: Weaving Success for Everyone.

ERIC Educational Resources Information Center

Ide, Janet L.

2000-01-01

Describes "Snakes in the Grass," a weaving project used with special needs students. Discusses the preliminary skill-building activities used, the process for creating the students' individual snakes, and the preparation and process for how the students wove the snakes. (CMK)

The effect of woven and non-woven fiber structure on mechanical properties polyester composite reinforced kenaf

NASA Astrophysics Data System (ADS)

Ratim, S.; Bonnia, N. N.; Surip, S. N.

2012-07-01

The effects of woven and non-woven kenaf fiber on mechanical properties of polyester composites were studied at different types of perform structures. Composite polyester reinforced kenaf fiber has been prepared via hand lay-up process by varying fiber forms into plain weave, twill and mats structure. The reinforcing efficiency of different fiber structure was compared with control of unreinforced polyester sample. It was found that the strength and stiffness of the composites are largely affected by fiber structure. A maximum value for tensile strength of composite was obtained for twill weave pattern of fiber structure while no significant different for plain weave and mat structure. The elastic modulus of composite has shown some improvement on plain and twill weave pattern. Meanwhile, lower value of modulus elasticity achieved by mats structure composite as well as control sample. The modulus of rupture and impact resistance were also analyzed. The improvement of modulus of rupture value can be seen on plain and twill weave pattern. However impact resistance doesn't show significant improvement in all types of structure except for mat fiber. The mechanical properties of kenaf fiber reinforced polyester composite found to be increased with woven and non-woven fiber structures in composite.

Oh What a Tangled Biofilm Web Bacteria Weave

MedlinePlus

... What a Tangled Biofilm Web Bacteria Weave Inside Life Science View All Articles | Inside Life Science Home Page Oh What a Tangled Biofilm Web ... Cellular Conversations Learning from Bacterial Chatter This Inside Life Science article also appears on LiveScience . Learn about related ...

Use of better designed hand knotting carpet looms and workplace interventions to improve working conditions of adult carpet weavers and to reduce hazardous child labor in carpet weaving in Pakistan.

PubMed

Awan, Saeed; Nasrullah, Muazzam

2013-01-01

Children and adults involved in carpet weaving are prone to a number of health and safety problems. This paper describes initial impact of an ergonomically designed loom and work place modifications, to encourage young and adult workers to weave carpets and reduce the hazardous child labor in carpet weaving in the province of Punjab, Pakistan. A new carpet loom with improved ergonomic and safety features suitable for adult carpet weavers was designed. Model carpet weaving worksites based on the new loom and better work environment were created in 30 villages. The impact of new loom compared with the traditional looms was assessed through structured questionnaires and health examinations after 24 months. Adolescent (15-17 years) and adult (> 17 years) participants included 75 respondents (males 10.7%, n=8; females 89.3%, n=67) operating under the new conditions and 92 respondents (males 12%, n=11; females 88%, n=81) operating under traditional conditions. Results indicated an improvement of health related complaints among those working in the new conditions, most notable were the differences in joint pain (p=0.002) and respiratory health (p=0.02). Improvement of income was also reported by workers at model workplaces. Also, no children below the age of 14 were found to be working at the new looms. The results indicate that individuals who adopted new looms and workplace interventions reported less joint pain and better respiratory health than those working with traditional looms in a traditional work environment. By reducing the risks in the workplace, this ergonomic intervention has the potential to reduce or eliminate hazardous child labor from carpet weaving.

Procedure for analysis and design of weaving sections : volume 2, users guide.

DOT National Transportation Integrated Search

1983-12-01

This research was performed to complete and advance the status of recently developed procedures for analysis and design of weaving sections (known as the Leisch method and-initially published in the 1979 issue of ITE Journal). The objective was to en...

ZnO nanosheet arrays constructed on weaved titanium wire for CdS-sensitized solar cells

PubMed Central

2014-01-01

Ordered ZnO nanosheet arrays were grown on weaved titanium wires by a low-temperature hydrothermal method. CdS nanoparticles were deposited onto the ZnO nanosheet arrays using the successive ionic layer adsorption and reaction method to make a photoanode. Nanoparticle-sensitized solar cells were assembled using these CdS/ZnO nanostructured photoanodes, and their photovoltaic performance was studied systematically. The best light-to-electricity conversion efficiency was obtained to be 2.17% under 100 mW/cm2 illumination, and a remarkable short-circuit photocurrent density of approximately 20.1 mA/cm2 was recorded, which could attribute to the relatively direct pathways for transportation of electrons provided by ZnO nanosheet arrays as well as the direct contact between ZnO and weaved titanium wires. These results indicate that CdS/ZnO nanostructures on weaved titanium wires would open a novel possibility for applications of low-cost solar cells. PMID:24618047

Standard operation procedures for conducting the on-the-road driving test, and measurement of the standard deviation of lateral position (SDLP).

PubMed

Verster, Joris C; Roth, Thomas

2011-01-01

This review discusses the methodology of the standardized on-the-road driving test and standard operation procedures to conduct the test and analyze the data. The on-the-road driving test has proven to be a sensitive and reliable method to examine driving ability after administration of central nervous system (CNS) drugs. The test is performed on a public highway in normal traffic. Subjects are instructed to drive with a steady lateral position and constant speed. Its primary parameter, the standard deviation of lateral position (SDLP), ie, an index of 'weaving', is a stable measure of driving performance with high test-retest reliability. SDLP differences from placebo are dose-dependent, and do not depend on the subject's baseline driving skills (placebo SDLP). It is important that standard operation procedures are applied to conduct the test and analyze the data in order to allow comparisons between studies from different sites.

Two new species of the orb-weaving spider genus Alpaida (Araneae, Araneidae) from Peru.

PubMed

Deza, Mariajosé; Andía, Juan Manuel

2014-07-02

Two new species of the orb-weaving spider genus Alpaida O. P.-Cambridge, 1889 are described and illustrated; Alpaida losamigos n. sp. based on females from Madre de Dios, and Alpaida penca n. sp. based on females and males from Cajamarca.

Weaving in the Story of Science

ERIC Educational Resources Information Center

Kirchhoff, Allison

2008-01-01

Stories weave common elements of the nature of science between topics and activities, regardless of whether it's short historical narratives about scientists or current event articles that are read. Stories also can help students realize the important contributions of persons of color, women, and other traditionally underrepresented groups. In…

A sustainable slashing industry using biodegradable sizes from modified soy protein to replace petro-based poly(vinyl alcohol).

PubMed

Zhao, Yi; Zhao, Yuzhu; Xu, Helan; Yang, Yiqi

2015-02-17

Biodegradable sizing agents from triethanolamine (TEA) modified soy protein could substitute poly(vinyl alcohol)(PVA) sizes for high-speed weaving of polyester and polyester/cotton yarns to substantially decrease environmental pollution and impel sustainability of textile industry. Nonbiodegradable PVA sizes are widely used and mainly contribute to high chemical oxygen demand (COD) in textile effluents. It has not been possible to effectively degrade, reuse or replace PVA sizes so far. Soy protein with good biodegradability showed potential as warp sizes in our previous studies. However, soy protein sizes lacked film flexibility and adhesion for required high-speed weaving. Additives with multiple hydroxyl groups, nonlinear molecule, and electric charge could physically modify secondary structure of soy protein and lead to about 23.6% and 43.3% improvement in size adhesion and ability of hair coverage comparing to unmodified soy protein. Industrial weaving results showed TEA-soy protein had relative weaving efficiency 3% and 10% higher than PVA and chemically modified starch sizes on polyester/cotton fabrics, and had relative weaving efficiency similar to PVA on polyester fabrics, although with 3- 6% lower add-on. In addition, TEA-soy sizes had a BOD5/COD ratio of 0.44, much higher than 0.03 for PVA, indicating that TEA-soy sizes were easily biodegradable in activated sludge.

Procedure for analysis and design of weaving sections : volume 1, research findings and development of techniques for application.

DOT National Transportation Integrated Search

1983-12-01

This research was performed to complete and advance the status of recently developed : procedures for analysis and design of weaving sections (known as the Leisch method and-initially published in the 1979 issue of ITE Journal). The objective was to ...

Weaving Contexts of Participation Online: The Digital Tapestry of Secondary English Teachers

ERIC Educational Resources Information Center

Rodesiler, Luke

2014-01-01

This article presents research from a qualitative study exploring five secondary English teachers' professionally oriented participation online. Drawing upon Cole's (1996) "surround" and "weaving" views of context, the specific line of research featured here was guided by the following question: What are the features of the…

Wissa Wassef's Experiment: The Phoenix of Egyptian Weaving.

ERIC Educational Resources Information Center

Court, Elsbeth

1985-01-01

The gallery and weaving workshops of the Wissa Wassef School, located near Cairo, Egypt, are described. The school was started 30 years ago by the Egyptian architect Wissa Wassef, who believed in innate creativity and the need to encourage artistic creation by the practice of the craft from early childhood. (RM)

30 CFR 7.23 - Application requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... products if the products differ only in: weight of the finished product; weight or weave of the same fabric... information: (1) Trade name. (2) Product designations (for example, style and code number). (3) Color. (4...) Scrim: Type, denier, weight, weave, the supplier, supplier's stock number or designation, and percent of...

30 CFR 7.23 - Application requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... products if the products differ only in: weight of the finished product; weight or weave of the same fabric... information: (1) Trade name. (2) Product designations (for example, style and code number). (3) Color. (4...) Scrim: Type, denier, weight, weave, the supplier, supplier's stock number or designation, and percent of...

Evaluation of the impact response of textile composites

NASA Technical Reports Server (NTRS)

Portanova, M. A.

1995-01-01

An evaluation of the impact damage resistance and impact damage tolerance of stitched and unstitched uniweaves, 2-D braids, and 3-D weaves was conducted. Uniweave laminates were tested at four thicknesses to determine the sensitivity of the tests to this parameter. Several braid and weave parameters were also varied to establish their velocity (large mass) impacts and then loaded in tension or compression to measure residual strength. Experimental results indicate that stitching significantly improves the uniweaves' damage resistance. The 2-D braids and 3-D weaves offered less damage resistance than the stitched materials. Stitching also improved the compression after impact (CAI) and tension after impact (TAI) strengths of the uniweave materials.

Weaving the tapestry of learning: simulation, standardized patients, and virtual communities.

PubMed

Holland, Brian; Landry, Karen; Mountain, Angela; Middlebrooks, Mary Alice; Heim, Deborah; Missildine, Kathy

2013-01-01

Using situated cognition learning theory, nursing faculty developed simulated clinical learning experiences integrating virtual communities and standardized patients. These learning experiences provide authenticity and realism not easily achieved using the individual techniques in isolation. The authors describe the process of weaving these strategies into a rich learning experience for students.

An Absorbing Look at Terry-Cloth Towels

ERIC Educational Resources Information Center

Moyer, Richard; Everett, Susan

2010-01-01

This article describes a lesson where students explore the absorbency of several towels with different weaves and weights. The lesson follows the 5E learning-cycle model and incorporates engineering in the sense of product testing with a focus on the relationship between the weave of a towel and its absorbency. The National Science Education…

SRB thermal curtain design support

NASA Technical Reports Server (NTRS)

Dixon, Carl A.; Lundblad, Wayne E.; Koenig, John R.

1992-01-01

Improvements in SRB Thermal Curtain were identified by thermal design featuring: selection of materials capable of thermal protection and service temperatures by tri-layering quartz, S2 glass, and Kevlar in thinner cross section; weaving in single piece (instead of 24 sections) to achieve improved strength; and weaving to reduce manufacturing cost with angle interlock construction.

Learning and Teaching Together: Weaving Indigenous Ways of Knowing into Education

ERIC Educational Resources Information Center

Tanaka, Michele T. D.

2016-01-01

Across Canada, new curriculum initiatives require teachers to introduce students to Aboriginal content. In response, many teachers unfamiliar with Aboriginal approaches to learning and teaching are seeking ways to respectfully weave this material into their lessons. At the same time, many teachers are also grappling with how to foster inclusive…

75 FR 53642 - Narrow Woven Ribbons With Woven Selvedge From the People's Republic of China: Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-01

... any color, style, pattern, or weave construction, including but not limited to single-faced satin..., styles, patterns, and/or weave constructions; Have been subjected to, or composed of materials that have... DEPARTMENT OF COMMERCE International Trade Administration [C-570-953] Narrow Woven Ribbons With...

The Weaving of a Tapestry: A Metaphor for Teacher Education Curriculum Development

ERIC Educational Resources Information Center

Simon, Susan E

2013-01-01

Teacher educators rightfully dream of delivering inspiring programs to benefit future teachers and the students they will in turn inspire. However, in the current teacher education environment in Australia, the artisan's craft of weaving rich texture and producing a masterpiece is potentially over-shadowed by the educational administrator's…

2D net shape weaving for cost effective manufacture of textile reinforced composites

NASA Astrophysics Data System (ADS)

Vo, D. M. P.; Kern, M.; Hoffmann, G.; Cherif, C.

2017-10-01

Despite significant weight and performance advantages over metal parts, the today’s demand for fibre-reinforced polymer composites (FRPC) has been limited mainly by their large manufacturing cost. The combination of dry textile preforms and low-cost consolidation processes such as resin transfer molding (RTM) has been appointed as a promising approach to low-cost FRPC manufacture. At the current state of the art, tooling and impregnation technology is well understood whereas preform fabrication technology has not been developed effectively. This paper presents an advanced 2D net shape weaving technology developed with the aim to establish a more cost effective system for the manufacture of dry textile preforms for FRPC. 2D net shape weaving is developed based on open reed weave (ORW) technology and enables the manufacture of 2D contoured woven fabrics with firm edge, so that oversize cutting and hand trimming after molding are no longer required. The introduction of 2D net shape woven fabrics helps to reduce material waste, cycle time and preform manufacturing cost significantly. Furthermore, higher grade of automation in preform fabrication can be achieved.

Development of 3D woven cellular structures for adaptive composites based on thermoplastic hybrid yarns

NASA Astrophysics Data System (ADS)

Sennewald, C.; Vorhof, M.; Schegner, P.; Hoffmann, G.; Cherif, C.; Boblenz, J.; Sinapius, M.; Hühne, C.

2018-05-01

Flexible cellular 3D structures with structure-inherent compliance made of fiber-reinforced composites have repeatedly aroused the interest of international research groups. Such structures offer the possibility to meet the increasing demand for flexible and adaptive structures. The aim of this paper is the development of cellular 3D structures based on weaving technology. Considering the desired geometry of the 3D structure, algorithms are developed for the formation of geometry through tissue sub-areas. Subsequently, these sub-areas are unwound into the weaving level and appropriate weave patterns are developed. A particular challenge is the realization of compliant mechanisms in the woven fabric. This can be achieved either by combining different materials or, in particular, by implementing large stiffness gradients by means of varying the woven fabrics thickness, whereas differences in wall thickness have to be realized with a factor of 1:10. A manufacturing technology based on the weaving process is developed for the realization of the developed 3D cellular structures. To this end, solutions for the processing of hybrid thermoplastic materials (e.g. tapes), solutions for the integration of inlays in the weaving process (thickening of partial areas), and solutions for tissue retraction, as well as for the fabric pull-off (linear pull-off system) are being developed. In this way, woven cellular 3D structures with woven outer layers and woven joint areas (compliance) can be realized in a single process step and are subsequently characterized.

Influence of Fibre Architecture on Impact Damage Tolerance in 3D Woven Composites

NASA Astrophysics Data System (ADS)

Potluri, P.; Hogg, P.; Arshad, M.; Jetavat, D.; Jamshidi, P.

2012-10-01

3D woven composites, due to the presence of through-thickness fibre-bridging, have the potential to improve damage tolerance and at the same time to reduce the manufacturing costs. However, ability to withstand damage depends on weave topology as well as geometry of individual tows. There is an extensive literature on damage tolerance of 2D prepreg laminates but limited work is reported on the damage tolerance of 3D weaves. In view of the recent interest in 3D woven composites from aerospace as well as non-aerospace sectors, this paper aims to provide an understanding of the impact damage resistance as well as damage tolerance of 3D woven composites. Four different 3D woven architectures, orthogonal, angle interlocked, layer-to-layer and modified layer-to-layer structures, have been produced under identical weaving conditions. Two additional structures, Unidirectional (UD) cross-ply and 2D plain weave, have been developed for comparison with 3D weaves. All the four 3D woven laminates have similar order of magnitude of damage area and damage width, but significantly lower than UD and 2D woven laminates. Damage Resistance, calculated as impact energy per unit damage area, has been shown to be significantly higher for 3D woven laminates. Rate of change of CAI strength with impact energy appears to be similar for all four 3D woven laminates as well as UD laminate; 2D woven laminate has higher rate of degradation with respect to impact energy. Undamaged compression strength has been shown to be a function of average tow waviness angle. Additionally, 3D weaves exhibit a critical damage size; below this size there is no appreciable reduction in compression strength. 3D woven laminates have also exhibited a degree of plasticity during compression whereas UD laminates fail instantly. The experimental work reported in this paper forms a foundation for systematic development of computational models for 3D woven architectures for damage tolerance.

Weaving Student Engagement into the Core Practices of Schools. A National Dropout Prevention Center/Network Position Paper

ERIC Educational Resources Information Center

Dary, Teri; Pickeral, Terry; Shumer, Rob; Williams, Anderson

2016-01-01

This position paper on student engagement is organized in response to major questions on how student engagement aligns with dropout prevention. Through a set of questions and responses, the "Weaving Student Engagement Into the Core Practices of Schools" position paper on student engagement : (1) defines the term "student…

Weaving the Cloth of Literacy: The Relationship between Braille and Reading.

ERIC Educational Resources Information Center

Zago, P. A.

1996-01-01

This brief article uses a weaving metaphor to address the relationship between braille and reading, with prior knowledge (the warp threads) interacting with reading content (the weft threads) by means of braille (the shuttle). Reading is seen to be an interactive process between reader, text, and the context of the reading situation. (DB)

75 FR 41808 - Narrow Woven Ribbons With Woven Selvedge From the People's Republic of China: Final Determination...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-19

... may: Also include natural or other non-man-made fibers; Be of any color, style, pattern, or weave..., twill, jacquard, or a combination of two or more colors, styles, patterns, and/or weave constructions... DEPARTMENT OF COMMERCE International Trade Administration [A-570-952] Narrow Woven Ribbons With...

POF-yarn weaves: controlling the light out-coupling of wearable phototherapy devices

PubMed Central

Quandt, Brit M.; Pfister, Marisa S.; Lübben, Jörn F.; Spano, Fabrizio; Rossi, René M.; Bona, Gian-Luca; Boesel, Luciano F.

2017-01-01

Neonatal jaundice (hyperbilirubinaemia) is common in neonates and, often, intensive blue-light phototherapy is required to prevent long-term effects. A photonic textile can overcome three major incubator-related concerns: Insulation of the neonate, human contact, and usage restraints. This paper describes the development of a homogeneous luminous textile from polymer optical fibres to use as a wearable, long-term phototherapy device. The bend out-coupling of light from the POFs was related to the weave production, e.g. weave pattern and yarn densities. Comfort, determined by friction against a skin model and breathability, was investigated additionally. Our textile is the first example of phototherapeutic clothing that is produced sans post-processing allowing for faster commercial production. PMID:29082067

WEAVE-QSO: A Massive Intergalactic Medium Survey for the William Herschel Telescope

NASA Astrophysics Data System (ADS)

Pieri, M. M.; Bonoli, S.; Chaves-Montero, J.; Pâris, I.; Fumagalli, M.; Bolton, J. S.; Viel, M.; Noterdaeme, P.; Miralda-Escudé, J.; Busca, N. G.; Rahmani, H.; Peroux, C.; Font-Ribera, A.; Trager, S. C.

2016-12-01

In these proceedings we describe the WEAVE-QSO survey, which will observe around 400,000 high redshift quasars starting in 2018. This survey is part of a broader WEAVE survey to be conducted at the 4.2m William Herschel Telescope. We will focus on chiefly on the science goals, but will also briefly summarise the target selection methods anticipated and the expected survey plan. Understanding the apparent acceleration in the expansion of the Universe is one of the key scientific challenges of our time. Many experiments have been proposed to study this expansion, using a variety of techniques. Here we describe a survey that can measure this acceleration and therefore help elucidate the nature of dark energy: a survey of the Lyα forest (and quasar absorption in general) in spectra towards z>2 quasars (QSOs). Further constraints on neutrino masses and warm dark matter are also anticipated. The same data will also shed light on galaxy formation via study of the properties of inflowing/outflowing gas associated with nearby galaxies and in a cosmic web context. Gas properties are sensitive to density, temperature, UV radiation, metallicity and abundance pattern, and so constraint galaxy formation in a variety of ways. WEAVE-QSO will study absorbers with a dynamic range spanning more than 8 orders of magnitude in column density, their thermal broadening, and a host of elements and ionization species. A core principal of the WEAVE-QSO survey is the targeting of QSOs with near 100% efficiency principally through use of the J-PAS (r < 23.2) and Gaia (r ≲ 20) data.

Design and optimization of a novel bio-loom to weave melt-spun absorbable polymers for bone tissue engineering.

PubMed

Gilmore, Jordon; Burg, Timothy; Groff, Richard E; Burg, Karen J L

2017-08-01

Bone graft procedures are currently among the most common surgical procedures performed worldwide, but due to high risk of complication and lack of viable donor tissue, there exists a need to develop alternatives for bone defect healing. Tissue engineering, for example, combining biocompatible scaffolds with mesenchymal stem cells to achieve new bone growth, is a possible solution. Recent work has highlighted the potential for woven polymer meshes to serve as bone tissue engineering scaffolds; since, scaffolds can be iteratively designed by adjusting weave settings, material types, and mesh parameters. However, there are a number of material and system challenges preventing the implementation of such a tissue engineering strategy. Fiber compliance, tensile strength, brittleness, cross-sectional geometry, and size present specific challenges for using traditional textile weaving methods. In the current work, two potential scaffold materials, melt-spun poly-l-lactide, and poly-l-lactide-co-ε-caprolactone, were investigated. An automated bio-loom was engineered and built to weave these materials. The bio-loom was used to successfully demonstrate the weaving of these difficult-to-handle fiber types into various mesh configurations and material combinations. The dobby-loom design, adapted with an air jet weft placement system, warp tension control system, and automated collection spool, provides minimal damage to the polymer fibers while overcoming the physical constraints presented by the inherent material structure. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1342-1351, 2017. © 2016 Wiley Periodicals, Inc.

Weaving Wisdom with Hard Work: Accomplished Student Learns, Grows, and Gives Back

ERIC Educational Resources Information Center

Kuhl, Eleanor

2010-01-01

Linda Taylor (Dine) raises sheep and horses, creates sculpture, paints, teaches traditional weaving classes, hunts solo for elk and deer, and volunteers at the Methodist Thrift Shop. In the past, she has also cared for Native children in need, and she is currently applying to foster a Navajo girl. On weekends, she sells bales of hay at the…

The Power of Social Networks: A Model for Weaving the Scholarship of Teaching and Learning into Institutional Culture

ERIC Educational Resources Information Center

Williams, Andrea L.; Verwood, Roselynn; Beery, Theresa A.; Dalton, Helen; McKinnon, James; Strickland, Karen; Pace, Jessica; Poole, Gary

2013-01-01

This paper offers a guide for those seeking to integrate the Scholarship of Teaching and Learning (SoTL) into higher education institutions to improve the quality of student learning. The authors posit that weaving SoTL into institutional cultures requires the coordinated actions of individuals working in linked social networks rather than…

75 FR 41804 - Notice of Final Determination of Sales at Less Than Fair Value: Narrow Woven Ribbons with Woven...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-19

... include natural or other non-man-made fibers; be of any color, style, pattern, or weave construction..., jacquard, or a combination of two or more colors, styles, patterns, and/or weave constructions; have been... of Sales at Less Than Fair Value: Narrow Woven Ribbons with Woven Selvedge from Taiwan AGENCY: Import...

Fibre positioning algorithms for the WEAVE spectrograph

NASA Astrophysics Data System (ADS)

Terrett, David L.; Lewis, Ian J.; Dalton, Gavin; Abrams, Don Carlos; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Middleton, Kevin; Trager, Scott C.

2014-07-01

WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. It is a multi-object "pick and place" fibre fed spectrograph with more than one thousand fibres, similar in concept to the Australian Astronomical Observatory's 2dF1 instrument with two observing plates, one of which is observing the sky while other is being reconfigured by a robotic fibre positioner. It will be capable of acquiring more than 10000 star or galaxy spectra a night. The WEAVE positioner concept uses two robots working in tandem in order to reconfigure a fully populated field within the expected 1 hour dwell-time for the instrument (a good match between the required exposure times and the limit of validity for a given configuration due to the effects of differential refraction). This presents additional constraints and complications for the software that determines the optimal path from one configuration to the next, particularly given the large number of fibre crossings implied by the 1000 fibre multiplex. This paper describes the algorithms and programming techniques used in the prototype implementations of the field configuration tool and the fibre positioner robot controller developed to support the detailed design of WEAVE.

Simulation of Complex Cracking in Plain Weave C/SiC Composite under Biaxial Loading

NASA Technical Reports Server (NTRS)

Cheng, Ron-Bin; Hsu, Su-Yuen

2012-01-01

Finite element analysis is performed on a mesh, based on computed geometry of a plain weave C/SiC composite with assumed internal stacking, to reveal the pattern of internal damage due to biaxial normal cyclic loading. The simulation encompasses intertow matrix cracking, matrix cracking inside the tows, and separation at the tow-intertow matrix and tow-tow interfaces. All these dissipative behaviors are represented by traction-separation cohesive laws. Not aimed at quantitatively predicting the overall stress-strain relation, the simulation, however, does not take the actual process of fiber debonding into account. The fiber tows are represented by a simple rule-of-mixture model where the reinforcing phase is a hypothetical one-dimensional material. Numerical results indicate that for the plain weave C/SiC composite, 1) matrix-crack initiation sites are primarily determined by large intertow matrix voids and interlayer tow-tow contacts, 2) the pattern of internal damage strongly depends on the loading path and initial stress, 3) compressive loading inflicts virtually no damage evolution. KEY WORDS: ceramic matrix composite, plain weave, cohesive model, brittle failure, smeared crack model, progressive damage, meso-mechanical analysis, finite element.

Acoustic emission monitoring of damage in ceramic matrix composites: Effects of weaves and feature

NASA Astrophysics Data System (ADS)

Ojard, Greg; Mordasky, Matt; Kumar, Rajesh

2018-04-01

Ceramic matrix composites (CMCs) are a class of high temperature materials with better damage tolerance properties compared to monolithic ceramics. The improved toughness is attributed to weak interface coating between the fiber and the matrix that allows for crack deflection and fiber pull-out. Thus, CMCs have gained consideration over monolithic materials for high temperature applications such as in gas turbines. The current standard fiber architecture for CMCs is a harness satin (HS) balanced weave (5HS and 8HS); however, other architectures such as uni-weave materials (tape layup) are now being considered due to fiber placement control and higher fiber volume fraction in the tensile loading direction. Engineering components require additional features in the CMC laminates, such as holes for attachments. Past work has shown that acoustic emission could differentiate the effect of changing interface conditions due to heat treatment effects. The focus of the present work is to investigate the effects of different weaves and the presence of a feature on damage behavior of CMCs as observed via acoustic emission technique. The results of the tensile testing with acoustic emission monitoring will be presented and discussed.

Out-of-plane properties

NASA Technical Reports Server (NTRS)

Jackson, Wade C.; Portanova, Marc A.

1995-01-01

This paper summarizes three areas of research which were performed to characterize out-of-plane properties of composite materials. In the first investigation, a series of tests was run to characterize the through-the-thickness tensile strength for a variety of composites that included 2D braids, 2D and 3D weaves, and prepreg tapes. A new test method based on a curved beam was evaluated. Failures were significantly different between the 2D materials and the 3D weaves. The 2D materials delaminated between layers due to out-of-plane tensile stresses while the 3D weaves failed due to the formation of radial cracks between the surface plies caused by high circumferential stresses along the inner radius. The strength of the 2D textile composites did not increase relative to the tapes. Final failure in the 3D weaves was caused by a circumferential crack similar to the 2D materials and occurred at a lower bending moment than in other materials. The early failures in the 3D weaves were caused by radial crack formation rather than a low through-the-thickness strength. The second investigation focused on the development of a standard impact test method to measure impact damage resistance. The only impact tests that currently exist are compression after impact (CAI) tests which incorporate elements of both damage resistance and damage tolerance. A new impact test method is under development which uses a quasi-static indentation (QSI) test to directly measure damage resistance. Damage resistance is quantified in terms of the contact force to produce a unit of damage where a metric for damage may be area in C-scan, depth of residual dent , penetration, damage growth, etc. A final draft of an impact standard that uses a QSI test method will be presented to the ASTM Impact Task Group on impact. In the third investigation, the impact damage resistance behavior of a variety of textile materials was studied using the QSI test method. In this study, the force where large damage initiates was measured and the delamination size as a function of force was determined. The force to initiate large damage was significantly lower in braids and weaves. The delamination diameter - impact forace relationship was quanitfied using a damage resistance parameter, Q(*), which related delamination diameter to imapct force over a range of delamination sizes. Using this Q(*) parameter to rate the materials, the stitched uniweaves, toughened epoxy tapes, and through-the-thickness orthogonal interlock weave were the most damage resistant.

Learning to Weave the Threads of Honor: Understanding the Value of Female Schooling in Southern Morocco

ERIC Educational Resources Information Center

Naji, Myriem

2012-01-01

This article is concerned with the role of formal education in the upward social mobility of women in the Sirwa, a marginal Berber region of southern Morocco where carpets are produced by women, and marketed by men. To explore why girls' education in weaving takes precedence over formal education, the article considers the place of women's…

Outdoor Education across America: "Weaving the Web." Selected Papers, Activities, and Resources from the 1987 National Outdoor Education Conference (Cortland, New York, October 9-12, 1987).

ERIC Educational Resources Information Center

Yerkes, Rita, Comp.; And Others

Selected through a refereed process from presentations given by speakers at the "1987 Outdoor Education across America: Weaving the Web" Conference, the content represents philosophy, ideas, program activities, and research of outdoor practitioners and leaders across America. The 25 presentations/workshops are summarized under the broad…

The WEAVE focus translation system: from design to construction

NASA Astrophysics Data System (ADS)

Canchado, Manuel; Romero, Antonio; Maroto, Óscar; Tomas, Albert; Martín-Nuño, Carlos; Casalta, Joan Manel; Prida, Joaquín.; L. Aguerri, J. Alfonso; Herreros, José Miguel; Delgado, José Miguel; Burgal, José Alonso; Abrams, Don Carlos; Dee, Kevin; Dalton, Gavin; Bonifacio, Piercarlo; Trager, Scott C.; Vallenari, Antonella

2016-07-01

WEAVE is a new wide-field spectroscopy facility proposed for the prime focus of the 4.2m William Herschel Telescope (WHT), placed in La Palma, Canary Islands, Spain. To allow for the compensation of the effects of temperature-induced and gravity-induced image degradation, the WEAVE prime focus assembly will be translated along the telescope optical axis. The assembly comprises the prime focus corrector with integrated ADC, a central mount for the corrector, an instrument rotator and a twin-focal-plane fibre positioner. Translation is accomplished through the use of a set of purpose-built actuators; collectively referred to as the Focus Translation System (FTS), formed by four independently-controlled Focus Translation Units (FTUs), eight vanes connecting the FTUs to a central can, and a central can hosting WEAVE Instrument. Each FTU is capable of providing a maximum stroke of +/-4mm with sufficient, combined force to move the five-tonne assembly with a positional accuracy of +/-20μm at a resolution of 5μm. The coordinated movement of the four FTUs allows +/-3mm WEAVE focus adjustment in the optical axis and +/-0.015° tilt correction in one axis. The control of the FTS is accomplished through a PLC-based subsystem that receives positional demands from the higher-level Instrument Control System. SENER has been responsible for designing, manufacturing and testing the FTS and the equipment required to manipulate and store the FTS together with the instrument. This manuscript describes the final design of the FTS along with the analyses and simulations that were performed, discusses the manufacturing procedures and the results of early verification prior to integration with the telescope. The plans for mounting the whole system on the telescope are also discussed.

Developments in fiber-positioning technology for the WEAVE instrument at the William Herschel Telescope

NASA Astrophysics Data System (ADS)

Schallig, Ellen; Lewis, Ian J.; Gilbert, James; Dalton, Gavin; Brock, Matthew; Abrams, Don Carlos; Middleton, Kevin; Aguerri, J. Alfonso L.; Bonifacio, Piercarlo; Carrasco, Esperanza; Trager, Scott C.; Vallenari, Antonella

2016-08-01

WEAVE is the next-generation wide-field optical spectroscopy facility for the William Herschel Telescope (WHT) on La Palma in the Canary Islands, Spain. It is a multi-object "pick-and-place" fibre-fed spectrograph with a 1000 fibre multiplex behind a new dedicated 2° prime focus corrector. The WEAVE positioner concept uses two robots working in tandem in order to reconfigure a fully populated field within the expected 1 hour dwell-time for the instrument (a good match between the required exposure times and the limit of validity for a given configuration due to the effects of differential refraction). In this paper we describe some of the final design decisions arising from the prototyping phase of the instrument design and provide an update on the current manufacturing status of the fibre positioner system.

Hemp reinforced composites: surface treatment, manufacturing method and fabric type effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cicala, G.; Cristaldi, G.; Recca, G.

2010-06-02

Hemp mats and weaved fabrics were used as received and after surface treatment as reinforcement for composites. Mercerization and amino silane surface treatments improved fibre/matrix adhesion and, as results, the mechanical properties of the composites were also improved. However, if surface treatment was too severe degradation of the mechanical properties of the single fibre was observed and this resulted in a reinforcing efficiency loss. Weaved fabrics obtained from twisted fibres in unidirectional and 0/90 deg. architecture were used. The use of weaved fabrics lead to high improvements of composite mechanical properties despite the absence of fibre's surface treatment. The specimensmore » manufactured by LRTM (Light Resin Transfer Moulding) showed enhanced mechanical properties compared to specimens made by hand lay up. Mechanical models were also used to predict the mechanical properties of the composites.« less

Hemp reinforced composites: surface treatment, manufacturing method and fabric type effects

NASA Astrophysics Data System (ADS)

Cicalạ, G.; Cristaldi, G.; Recca, G.

2010-06-01

Hemp mats and weaved fabrics were used as received and after surface treatment as reinforcement for composites. Mercerization and amino silane surface treatments improved fibre/matrix adhesion and, as results, the mechanical properties of the composites were also improved. However, if surface treatment was too severe degradation of the mechanical properties of the single fibre was observed and this resulted in a reinforcing efficiency loss. Weaved fabrics obtained from twisted fibres in unidirectional and 0/90° architecture were used. The use of weaved fabrics lead to high improvements of composite mechanical properties despite the absence of fibre's surface treatment. The specimens manufactured by LRTM (Light Resin Transfer Moulding) showed enhanced mechanical properties compared to specimens made by hand lay up. Mechanical models were also used to predict the mechanical properties of the composites.

Seamless Collapsible Fuel Tanks. Phase 1

DTIC Science & Technology

1982-03-01

TITLE (and Subtitle) 5. TYrE OF REPORT & PERIOD COVERED Final Report: Phase I Seamless Collapsible Fuel Tanks April 1980 - March 1982 6. PERFORMING...KEY WORDS (Continue on reverse side it neceessery nd identify by block number) tubular weaving, pillow tanks, fuel resistance , water resistance ...ends x 28 picks per inch in a plain or basket weave. The fabric is then coated both sides with an appropriate fuel- resistant compound, usually a nitrile

An Ontological Approach to Developing Information Operations Applications for Use on the Semantic Web

DTIC Science & Technology

2008-09-01

IWPC 21 Berners - Lee , Tim . (1999). Weaving the Web. New York: HarperCollins Publishers, Inc. 22... Berners - Lee , Tim . (1999). Weaving the Web. New York: HarperCollins Publishers, Inc. Berners - Lee , T., Hendler, J., & Lassila, O. (2001). The Semantic...environment where software agents roaming from page to page can readily carry out sophisticated tasks for users. T. Berners - Lee , J. Hendler, and O

Flame-resistant pure and hybrid woven fabrics from basalt

NASA Astrophysics Data System (ADS)

Jamshaid, H.; Mishra, R.; Militky, J.

2017-10-01

This work has been formulated to investigate the burning behavior of different type of fabrics. The main concentration is to see how long the fabric resists after it catches the fire and the propagation of fire can be reduced by using flame resistant fiber i.e basalt. Basalt fiber is an environmental friendly material with low input, high output, low energy consumption and less emission. The goal of present investigations is to show the dependence of fabric flammability on its structure parameters i.e weave type, blend type etc. Fabric weaves have strong effect on flammability properties. Plain weave has the lowest burning rate as the density of the plain weave fabric is more and the structure is tight which gives less chances of flame passing through the fabric. Thermal stability is evaluated with TGA of all hybrid and nonhybrid fabrics and compared. The thermal stability of the basalt fiber is excellent. When comparing thermal analysis curves for hybrid samples it demonstrates that thermal stability of the samples containing basalt is much higher than the non- hybrid samples. Percentage weight loss is less in hybrid samples as compared to non-hybrid samples. The effectiveness of hybridization on samples may be indicated by substantial lowering of the decomposition mass. Correlation was made between flammability with the infrared radiations (IR)

Failure Behaviour of Aluminium/CFRP Laminates with Varying Fibre Orientation in Quasi-static Indentation Test

NASA Astrophysics Data System (ADS)

Romli, N. K.; Rejab, M. R. M.; Bachtiar, D.; Siregar, J.; Rani, M. F.; Salleh, Salwani Mohd; Merzuki, M. N. M.

2018-03-01

The response of the aluminium/carbon laminate was examined by an experimental work. The investigation on fibre metal laminate behaviour was done through an indentation test in a quasi-static loading. The hybrid laminate was fabricated by a compression moulding technique and used two types of carbon fibre orientations; plain weave and unidirectional. The plain weave orientation is dry fibre, and unidirectional orientation is prepreg type fibre. The plain weave carbon fibre and aluminium alloy 2024-0 was laminated by using thermoset epoxy while the unidirectional carbon fibre was pressed by using a hot press machine and cured under a specific temperature and pressure. A compression moulding technique was used for the FML fabrication. The aluminium sheet metal has been roughening by a metal sanding method which to improve the bonding between the fibre and metal layer. The main objective of this paper is to determine the failure response of the laminate under five variation of the crosshead speeds in the quasi-static loading. Based on the experimental data of the test, the result of 1 mm/min in the plain weave CFRP has lower loading than unidirectional fibre which the value of both was 4.11 kN and 4.69 kN, respectively.

Making Air Pollution Visible: A Tool for Promoting Environmental Health Literacy.

PubMed

Cleary, Ekaterina Galkina; Patton, Allison P; Wu, Hsin-Ching; Xie, Alan; Stubblefield, Joseph; Mass, William; Grinstein, Georges; Koch-Weser, Susan; Brugge, Doug; Wong, Carolyn

2017-04-12

Digital maps are instrumental in conveying information about environmental hazards geographically. For laypersons, computer-based maps can serve as tools to promote environmental health literacy about invisible traffic-related air pollution and ultrafine particles. Concentrations of these pollutants are higher near major roadways and increasingly linked to adverse health effects. Interactive computer maps provide visualizations that can allow users to build mental models of the spatial distribution of ultrafine particles in a community and learn about the risk of exposure in a geographic context. The objective of this work was to develop a new software tool appropriate for educating members of the Boston Chinatown community (Boston, MA, USA) about the nature and potential health risks of traffic-related air pollution. The tool, the Interactive Map of Chinatown Traffic Pollution ("Air Pollution Map" hereafter), is a prototype that can be adapted for the purpose of educating community members across a range of socioeconomic contexts. We built the educational visualization tool on the open source Weave software platform. We designed the tool as the centerpiece of a multimodal and intergenerational educational intervention about the health risk of traffic-related air pollution. We used a previously published fine resolution (20 m) hourly land-use regression model of ultrafine particles as the algorithm for predicting pollution levels and applied it to one neighborhood, Boston Chinatown. In designing the map, we consulted community experts to help customize the user interface to communication styles prevalent in the target community. The product is a map that displays ultrafine particulate concentrations averaged across census blocks using a color gradation from white to dark red. The interactive features allow users to explore and learn how changing meteorological conditions and traffic volume influence ultrafine particle concentrations. Users can also select from multiple map layers, such as a street map or satellite view. The map legends and labels are available in both Chinese and English, and are thus accessible to immigrants and residents with proficiency in either language. The map can be either Web or desktop based. The Air Pollution Map incorporates relevant language and landmarks to make complex scientific information about ultrafine particles accessible to members of the Boston Chinatown community. In future work, we will test the map in an educational intervention that features intergenerational colearning and the use of supplementary multimedia presentations. ©Ekaterina Galkina Cleary, Allison P Patton, Hsin-Ching Wu, Alan Xie, Joseph Stubblefield, William Mass, Georges Grinstein, Susan Koch-Weser, Doug Brugge, Carolyn Wong. Originally published in JMIR Public Health and Surveillance (http://publichealth.jmir.org), 12.04.2017.

Room- and Low-Temperature Deformation of Multilayered Fiberglass Plastics Reinforced with a Fabric of Sateen Weave

NASA Astrophysics Data System (ADS)

Kucher, N. K.; Dveyrin, A. Z.; Zarazovskii, M. N.; Zemtsov, M. P.

2004-05-01

The regularities of elastic deformation of multilayered fiberglass plastics reinforced with a fabric of sateen weave are studied. The effect of cooling to 77 K on the averaged elastic characteristics of the orthotropic material is analyzed. The efficiency of mathematical modeling in calculating the stiffness and compliance parameters of the woven composites based on the geometry and mechanical properties of their constituents is investigated.

Quantifying Damage at Multiple Loading Rates to Kevlar KM2 Fibers Due to Weaving and Finishing

DTIC Science & Technology

2013-06-01

ARL-TR-6465 June 2013 Approved for public release; distribution is unlimited. NOTICES...ARL-TR-6465 June 2013 Quantifying Damage at Multiple Loading Rates to Kevlar KM2 Fibers Due to Weaving and Finishing Brett D. Sanborn...OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE (DD-MM-YYYY) June 2013 2. REPORT TYPE Final 3. DATES

Brookside Mills, Knox County, TN

EPA Pesticide Factsheets

Brookside Mills, located in Knox County, TN, was a textile mill that was founded in 1885 and at its peak employed over 1,000 people. Its former uses included fabric weaving, dying, and sewing operations. It was at some point a department store, and during a portion of its history, coal was used as an energy source. Weaving operations continued in some form at the Brookside factory until 1969. In 1996 the buildings were demolished.

Air-condition Control System of Weaving Workshop Based on LabVIEW

NASA Astrophysics Data System (ADS)

Song, Jian

The project of air-condition measurement and control system based on LabVIEW is put forward for the sake of controlling effectively the environmental targets in the weaving workshop. In this project, which is based on the virtual instrument technology and in which LabVIEW development platform by NI is adopted, the system is constructed on the basis of the virtual instrument technology. It is composed of the upper PC, central control nodes based on CC2530, sensor nodes, sensor modules and executive device. Fuzzy control algorithm is employed to achieve the accuracy control of the temperature and humidity. A user-friendly man-machine interaction interface is designed with virtual instrument technology at the core of the software. It is shown by experiments that the measurement and control system can run stably and reliably and meet the functional requirements for controlling the weaving workshop.

FRACTURE STRENGTH AND TIME DEPENDENT PROPERTIES OF 0/90 AND ±55-BRAIDED WEAVE SiC/SiC TYPE-S FIBER COMPOSITES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henager, Charles H.

PNNL has performed mechanical property tests on two types of Hi-Nicalon Type-S fiber SiC/SiC composites for the general purpose of evaluating such composites for control rod guide tube applications in the NGNP high-temperature gas-cooled reactor design. The mechanical testing consisted of 4-point bend strength, 4-point single-edge notched bend fracture toughness, and 4-point bend slow crack growth testing on both composites from ambient to 1600°C (1873K). The two composite materials that were tested included a ±55°-braided-weave composite with Type-S fibers inclined at 55° to the principal composite axes to simulate a braided tube architecture and a Type-S 0/90 satin-weave composite asmore » a reference material.« less

Low-temperature mechanical properties of glass/epoxy laminates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, R. P.; Madhukar, M.; Thaicharoenporn, B.

2014-01-27

Selected mechanical properties of glass/epoxy laminate candidates for use in the electrical turn and ground insulation of the ITER Central solenoid (CS) modules were measured. Short-beam shear and flexural tests have been conducted on various E-glass cloth weaves/epoxy laminates at 295 and 77 K. Types of glass weave include 1581, 7500, 7781, and 38050, which represent both satin and plain weaves. The epoxy, planned for use for vacuum-pressure impregnation of the CS module, consists of an anhydride-cured bisphenol F resin system. Inter-laminar shear strength, flexural elastic modulus, and flexural strength have been measured. The data indicate that these properties aremore » dependent on the volume percent of glass. Short-beam shear strength was measured as a function of the span-to-thickness ratio for all laminates at 77 K. Comprehensive fractography was conducted to obtain the failure mode of each short-beam shear test sample.« less

Knitting and weaving artificial muscles

PubMed Central

Maziz, Ali; Concas, Alessandro; Khaldi, Alexandre; Stålhand, Jonas; Persson, Nils-Krister; Jager, Edwin W. H.

2017-01-01

A need exists for artificial muscles that are silent, soft, and compliant, with performance characteristics similar to those of skeletal muscle, enabling natural interaction of assistive devices with humans. By combining one of humankind’s oldest technologies, textile processing, with electroactive polymers, we demonstrate here the feasibility of wearable, soft artificial muscles made by weaving and knitting, with tunable force and strain. These textile actuators were produced from cellulose yarns assembled into fabrics and coated with conducting polymers using a metal-free deposition. To increase the output force, we assembled yarns in parallel by weaving. The force scaled linearly with the number of yarns in the woven fabric. To amplify the strain, we knitted a stretchable fabric, exhibiting a 53-fold increase in strain. In addition, the textile construction added mechanical stability to the actuators. Textile processing permits scalable and rational production of wearable artificial muscles, and enables novel ways to design assistive devices. PMID:28138542

Low-temperature mechanical properties of glass/epoxy laminates

NASA Astrophysics Data System (ADS)

Reed, R. P.; Madhukar, M.; Thaicharoenporn, B.; Martovetsky, N. N.

2014-01-01

Selected mechanical properties of glass/epoxy laminate candidates for use in the electrical turn and ground insulation of the ITER Central solenoid (CS) modules were measured. Short-beam shear and flexural tests have been conducted on various E-glass cloth weaves/epoxy laminates at 295 and 77 K. Types of glass weave include 1581, 7500, 7781, and 38050, which represent both satin and plain weaves. The epoxy, planned for use for vacuum-pressure impregnation of the CS module, consists of an anhydride-cured bisphenol F resin system. Inter-laminar shear strength, flexural elastic modulus, and flexural strength have been measured. The data indicate that these properties are dependent on the volume percent of glass. Short-beam shear strength was measured as a function of the span-to-thickness ratio for all laminates at 77 K. Comprehensive fractography was conducted to obtain the failure mode of each short-beam shear test sample.

Integral Textile Structure for 3-D CMC Turbine Airfoils

NASA Technical Reports Server (NTRS)

Marshall, David B. (Inventor); Cox, Brian N. (Inventor); Sudre, Olivier H. (Inventor)

2017-01-01

An integral textile structure for 3-D CMC turbine airfoils includes top and bottom walls made from an angle-interlock weave, each of the walls comprising warp and weft fiber tows. The top and bottom walls are merged on a first side parallel to the warp fiber tows into a single wall along a portion of their widths, with the weft fiber tows making up the single wall interlocked through the wall's thickness such that delamination of the wall is inhibited. The single wall suitably forms the trailing edge of an airfoil; the top and bottom walls are preferably joined along a second side opposite the first side and parallel to the radial fiber tows by a continuously curved section in which the weave structure remains continuous with the weave structure in the top and bottom walls, the continuously curved section being the leading edge of the airfoil.

Ceramic Fiber Structures for Cryogenic Load-Bearing Applications

NASA Technical Reports Server (NTRS)

Jaskowiak, Martha H.; Eckel, Andrew J.

2009-01-01

This invention is intended for use as a load-bearing device under cryogenic temperatures and/or abrasive conditions (i.e., during missions to the Moon). The innovation consists of small-diameter, ceramic fibers that are woven or braided into devices like ropes, belts, tracks, or cables. The fibers can be formed from a variety of ceramic materials like silicon carbide, carbon, aluminosilicate, or aluminum oxide. The fiber architecture of the weave or braid is determined by both the fiber properties and the mechanical requirements of the application. A variety of weave or braid architectures is possible for this application. Thickness of load-bearing devices can be achieved by using either a 3D woven structure, or a layered, 2D structure. For the prototype device, a belt approximately 0.10 in. (0.25 cm) thick, and 3.0 in. (7.6 cm) wide was formed by layering and stitching a 2D aluminosilicate fiber weave.

Manufacture of multi-layer woven preforms

NASA Technical Reports Server (NTRS)

Mohamed, M. H.; Zhang, Z.; Dickinson, L.

1988-01-01

This paper reviews current three-dimensional weaving processes and discusses a process developed at the Mars Mission Research Center of North Carolina State University to weave three-dimensional multilayer fabrics. The fabrics may vary in size and complexity from simple panels to T-section or I-section beams to large stiffened panels. Parameters such as fiber orientation, volume fraction of the fiber required in each direction, yarn spacings or density, etc., which determine the physical properties of the composites are discussed.

Computer Representation of Fabric Pattern Weaves as Woven Fabric Samples and Texture Maps for Educational and Industrial Applications.

ERIC Educational Resources Information Center

Murtha, Judith Rush

The purpose of this study was to write a computer program that would not only output a color pattern weave to a cathode ray tube (CRT), but would also analyze a painted design and output a printed diagram that would show how to set up a loom in order to produce the woven design. The first of seven chapters describes the problem and the intent of…

The HARPS-N archive through a Cassandra, NoSQL database suite?

NASA Astrophysics Data System (ADS)

Molinari, Emilio; Guerra, Jose; Harutyunyan, Avet; Lodi, Marcello; Martin, Adrian

2016-07-01

The TNG-INAF is developing the science archive for the WEAVE instrument. The underlying architecture of the archive is based on a non relational database, more precisely, on Apache Cassandra cluster, which uses a NoSQL technology. In order to test and validate the use of this architecture, we created a local archive which we populated with all the HARPSN spectra collected at the TNG since the instrument's start of operations in mid-2012, as well as developed tools for the analysis of this data set. The HARPS-N data set is two orders of magnitude smaller than WEAVE, but we want to demonstrate the ability to walk through a complete data set and produce scientific output, as valuable as that produced by an ordinary pipeline, though without accessing directly the FITS files. The analytics is done by Apache Solr and Spark and on a relational PostgreSQL database. As an example, we produce observables like metallicity indexes for the targets in the archive and compare the results with the ones coming from the HARPS-N regular data reduction software. The aim of this experiment is to explore the viability of a high availability cluster and distributed NoSQL database as a platform for complex scientific analytics on a large data set, which will then be ported to the WEAVE Archive System (WAS) which we are developing for the WEAVE multi object, fiber spectrograph.

Signal processing and analyzing works of art

NASA Astrophysics Data System (ADS)

Johnson, Don H.; Johnson, C. Richard, Jr.; Hendriks, Ella

2010-08-01

In examining paintings, art historians use a wide variety of physico-chemical methods to determine, for example, the paints, the ground (canvas primer) and any underdrawing the artist used. However, the art world has been little touched by signal processing algorithms. Our work develops algorithms to examine x-ray images of paintings, not to analyze the artist's brushstrokes but to characterize the weave of the canvas that supports the painting. The physics of radiography indicates that linear processing of the x-rays is most appropriate. Our spectral analysis algorithms have an accuracy superior to human spot-measurements and have the advantage that, through "short-space" Fourier analysis, they can be readily applied to entire x-rays. We have found that variations in the manufacturing process create a unique pattern of horizontal and vertical thread density variations in the bolts of canvas produced. In addition, we measure the thread angles, providing a way to determine the presence of cusping and to infer the location of the tacks used to stretch the canvas on a frame during the priming process. We have developed weave matching software that employs a new correlation measure to find paintings that share canvas weave characteristics. Using a corpus of over 290 paintings attributed to Vincent van Gogh, we have found several weave match cliques that we believe will refine the art historical record and provide more insight into the artist's creative processes.

Polymer Infiltration Studies

NASA Technical Reports Server (NTRS)

Marchello, Joseph M.

1991-01-01

Progress was made on the preparation of carbon fiber composites using advanced polymer resins. Processes reported include powder towpreg process, weaving towpreg made from dry powder prepreg, composite from powder coated towpreg, and toughening of polyimide resin (PMR) composites by semi-interpenetrating networks. Several important areas of polymer infiltration into fiber bundles will be researched. Preparation to towpreg for textile preform weaving and braiding and for automated tow placement is a major goal, as are the continued development of prepregging technology and the various aspects of composite part fabrication.

Investigating comfort properties of 3/1 Z twill weaved denim fabrics

NASA Astrophysics Data System (ADS)

Taştan Özkan, E.; Kaplangiray, B.

2017-10-01

Denim jeans are preferred because of durability and easy washing properties. Nowadays the expectations of consumers from denim fabrics are changed towards design and comfort properties. Fort this reason, thermal and moisture comfort properties of denim fabrics should be examined. This paper aims to investigate thermal, air permeability and moisture management properties of 3/1 Z twill weaved denim fabrics. These fabrics are produced mainly from cotton with different yarn count and cover factors are close to each other.

Modeling Geometry and Progressive Failure of Material Interfaces in Plain Weave Composites

NASA Technical Reports Server (NTRS)

Hsu, Su-Yuen; Cheng, Ron-Bin

2010-01-01

A procedure combining a geometrically nonlinear, explicit-dynamics contact analysis, computer aided design techniques, and elasticity-based mesh adjustment is proposed to efficiently generate realistic finite element models for meso-mechanical analysis of progressive failure in textile composites. In the procedure, the geometry of fiber tows is obtained by imposing a fictitious expansion on the tows. Meshes resulting from the procedure are conformal with the computed tow-tow and tow-matrix interfaces but are incongruent at the interfaces. The mesh interfaces are treated as cohesive contact surfaces not only to resolve the incongruence but also to simulate progressive failure. The method is employed to simulate debonding at the material interfaces in a ceramic-matrix plain weave composite with matrix porosity and in a polymeric matrix plain weave composite without matrix porosity, both subject to uniaxial cyclic loading. The numerical results indicate progression of the interfacial damage during every loading and reverse loading event in a constant strain amplitude cyclic process. However, the composites show different patterns of damage advancement.

Experimental and numerical analysis of the influence of tyres' properties on the straight running stability of a sport-touring motorcycle

NASA Astrophysics Data System (ADS)

Cossalter, Vittore; Doria, Alberto; Formentini, Matteo; Peretto, Martino

2012-03-01

The behaviour of a motorcycle on the road is largely governed by tyre properties. This paper presents experimental and numerical analyses dealing with the influence of tyre properties on the stability of weave and wobble in straight running. The final goal is to find optimal sets of tyre properties that improve the stability of a motorcycle. The investigation is based on road tests carried out on a sport-touring motorcycle equipped with sensors. Three sets of tyres are tested at different speeds in the presence of weave and wobble. The analysis of telemetry data highlights significant differences in the trends of frequency and damping of weave and wobble against speed. The experimental analysis is integrated by a parametric numerical analysis. Tyre properties are varied according to the design of experiments method, in order to highlight the single effects on stability of lateral and cornering coefficient of front and rear tyres.

Comparative Study of 3-Dimensional Woven Joint Architectures for Composite Spacecraft Structures

NASA Technical Reports Server (NTRS)

Jones, Justin S.; Polis, Daniel L.; Segal, Kenneth N.

2011-01-01

The National Aeronautics and Space Administration (NASA) Exploration Systems Mission Directorate initiated an Advanced Composite Technology (ACT) Project through the Exploration Technology Development Program in order to support the polymer composite needs for future heavy lift launch architectures. As an example, the large composite structural applications on Ares V inspired the evaluation of advanced joining technologies, specifically 3D woven composite joints, which could be applied to traditionally manufactured barrel segments. Implementation of these 3D woven joint technologies may offer enhancements in damage tolerance without sacrificing weight. However, baseline mechanical performance data is needed to properly analyze the joint stresses and subsequently design/down-select a preform architecture. Six different configurations were designed and prepared for this study; each consisting of a different combination of warp/fill fiber volume ratio and preform interlocking method (z-fiber, fully interlocked, or hybrid). Tensile testing was performed for this study with the enhancement of a dual camera Digital Image Correlation (DIC) system which provides the capability to measure full-field strains and three dimensional displacements of objects under load. As expected, the ratio of warp/fill fiber has a direct influence on strength and modulus, with higher values measured in the direction of higher fiber volume bias. When comparing the z-fiber weave to a fully interlocked weave with comparable fiber bias, the z-fiber weave demonstrated the best performance in two different comparisons. We report the measured tensile strengths and moduli for test coupons from the 6 different weave configurations under study.

Using Response Surface Methods to Correlate the Modal Test of an Inflatable Test Article

NASA Technical Reports Server (NTRS)

Gupta, Anju

2013-01-01

This paper presents a practical application of response surface methods (RSM) to correlate a finite element model of a structural modal test. The test article is a quasi-cylindrical inflatable structure which primarily consists of a fabric weave, with an internal bladder and metallic bulkheads on either end. To mitigate model size, the fabric weave was simplified by representing it with shell elements. The task at hand is to represent the material behavior of the weave. The success of the model correlation is measured by comparing the four major modal frequencies of the analysis model to the four major modal frequencies of the test article. Given that only individual strap material properties were provided and material properties of the overall weave were not available, defining the material properties of the finite element model became very complex. First it was necessary to determine which material properties (modulus of elasticity in the hoop and longitudinal directions, shear modulus, Poisson's ratio, etc.) affected the modal frequencies. Then a Latin Hypercube of the parameter space was created to form an efficiently distributed finite case set. Each case was then analyzed with the results input into RSM. In the resulting response surface it was possible to see how each material parameter affected the modal frequencies of the analysis model. If the modal frequencies of the analysis model and its corresponding parameters match the test with acceptable accuracy, it can be said that the model correlation is successful.

The mechanical design for the WEAVE prime focus corrector system

NASA Astrophysics Data System (ADS)

Abrams, Don Carlos; Dee, Kevin; Agócs, Tibor; Lhome, Emilie; Peñate, José; Jaskó, Attila; Bányai, Evelin; Burgal, José A.; Dalton, Gavin; Middleton, Kevin; Bonifacio, Piercarlo; Aguerri, J. Alfonso L.; Trager, S. C.; Balcells, Marc

2014-08-01

WEAVE is the next-generation, wide-field, optical spectroscopy facility for the William Herschel Telescope (WHT) in La Palma, Canary Islands, Spain. The WHT will undergo a significant adaptation to accommodate this facility. A two- degree Prime Focus Corrector (PFC), that includes an Atmospheric Dispersion Compensator, is being planned and is currently in its final design phase. To compensate for the effects of temperature-induced image degradation, the entire PFC system will be translated along the telescope optical axis. The optical system comprises six lenses, the largest of which will have a diameter of 1.1m. Now that the optical elements are in production, the designs for the lens cells and the mounting arrangements are being analysed to ensure that the image quality of the complete system is better than 1.0 arcsec (80% encircled energy diameter) over the full field of view. The new PFC system is designed to be routinely interchanged with the existing top-end ring. This will maximise the versatility of the WHT and allow the two top-end systems to be interchanged as dictated by the scientific needs of the astronomers that will use WEAVE and other instruments on the telescope. This manuscript describes the work that has been carried out in developing the designs for the mechanical subsystems and the plans for mounting the lenses to attain an optical performance that is commensurate with the requirements derived from planning the WEAVE surveys.

Working Conditions in Carpet Weaving Workshops and Muscu-loskeletal Complaints among Workers in Tabriz - Iran

PubMed Central

Nazari, Jalil; Mahmoudi, Nader; Dianat, Iman; Graveling, Richard

2012-01-01

Background: Carpet weaving operations usualy involve poor working conditions that can lead to the development of musculoskeletal disorders (MSDs). This study investigated MSDs among car¬pet weavers in relation to working conditions from workers' view in Tabriz City, Northwest Iran. Methods: This cross-sectional and descriptive study was conducted in city of Tabriz, Iran. Data were col¬lected using interviews and questionnaires. The study population consisted of 200 randomly selected healthy weavers from twenty five active carpet weaving workshops. Results: The results showed a high prevalence of musculoskeletal problems among the study population. The most commonly affected body areas were neck, lower back, ankles/feet, hands/wrists, upper back, shoulders and knees, respectively. More than half of the weavers were not satisfied with the thermal con¬dition, noise level and cleanliness of the air in the workshops. The result indicated a significant relation¬ship between upper back symptoms and daily working time and between lower back symptoms and the numbers of rows of knots woven in a day. Weavers' satisfaction with hand tools shape and thermal condi¬tion of the workshops were associated with lower back symptoms, whereas satisfaction with weaving looms were associated with upper back complaints. Conclusion: The poor working condition of hand-woven carpet workshops such as environmental con¬ditions and work station design and tools should be the subject of ergonomics interventions. PMID:24688943

Woven TPS Mechanical Property Evaluation

NASA Technical Reports Server (NTRS)

Gonzales, Gregory Lewis; Kao, David Jan-Woei; Stackpoole, Margaret M.

2013-01-01

Woven Thermal Protection Systems (WTPS) is a relatively new program funded by the Office of the Chief Technologist (OCT). The WTPS approach to producing TPS architectures uses precisely engineered 3-D weaving techniques that allow tailoring material characteristics needed to meet specific mission requirements. A series of mechanical tests were performed to evaluate performance of different weave types, and get a better understanding of failure modes expected in these three-dimensional architectures. These properties will aid in material down selection and guide selection of the appropriate WTPS for a potential mission.

A Gaussian Weave for Kinematical Loop Quantum Gravity

NASA Astrophysics Data System (ADS)

Corichi, A.; Reyes, J. M.; Ashtekar, A.

Remarkable efforts in the study of the semiclassical regime of kinematical loop quantum gravity are currently underway. In this note, we construct a ``quasicoherent'' weave state using Gaussian factors. In a similar fashion to some other proposals, this state is peaked in both the connection and the spin network basis. However, the state constructed here has the novel feature that, in the spin network basis, the main contribution for this state is given by the fundamental representation, independently of the value of the parameter that regulates the Gaussian width.

Development of 3D Woven Ablative Thermal Protection Systems (TPS) for NASA Spacecraft

NASA Technical Reports Server (NTRS)

Feldman, Jay D.; Ellerby, Don; Stackpoole, Mairead; Peterson, Keith; Venkatapathy, Ethiraj

2015-01-01

The development of a new class of thermal protection system (TPS) materials known as 3D Woven TPS led by the Entry Systems and Technology Division of NASA Ames Research Center (ARC) will be discussed. This effort utilizes 3D weaving and resin infusion technologies to produce heat shield materials that are engineered and optimized for specific missions and requirements. A wide range of architectures and compositions have been produced and preliminarily tested to prove the viability and tailorability of the 3D weaving approach to TPS.

An evaluation of the real-world safety effect of a lane change driver support system and characteristics of lane change crashes based on insurance claims data.

PubMed

Isaksson-Hellman, Irene; Lindman, Magdalena

2018-02-28

Lane changes, which frequently occur when vehicles travel on major roads, may contribute to critical situations that significantly affect the traffic flow and traffic safety. Thus, knowledge of lane change situations is important for infrastructure improvements as well as for driver support systems and automated driving development projects. The objectives of this study were to evaluate the crash avoidance performance of a lane change driver support system, the Blind Spot Information System (BLIS) in Volvo car models, and to describe the characteristics of lane change crashes by analyzing detailed information from insurance claim reports. An overall evaluation of the safety effect of BLIS was performed by analyzing crash rate differences in lane change situations for cars with and without the optionally mounted BLIS system based on a population of 380,000 insured vehicle years. Further, crashes in which the repair cost of the host vehicle exceeded approximately US$1,250 were selected and compared. Finally, the study examined different precrash factors and crash configurations, using in-depth insurance claims data from representative lane change crash cases including all severity levels in a population of more than 200,000 insured vehicle years. The technology did not significantly reduce the overall number of crashes when all types of lane change crashes and severity levels were considered, though a significant crash-reducing effect of 31% for BLIS cars was found when more severe crashes with a repair cost exceeding US$1,250 were analysed. Cars with the BLIS technology also have a 30% lower claim cost on average for reported lane change crashes, indicating reduced crash severity. When stratifying the data into specific situations, by collecting precrash information in a case-by-case study, the influence of BLIS was indicated to differ for the evaluated situations, although no significant results were found. For example, during general lane change maneuvers (i.e., not while exiting or entering highways or during weaving/merging situations) the crash rate was reduced by 14%, whereas in weaving/merging situations the crash rate increased. The insurance data analyzed provided useful information about real-world lane change crash characteristics by covering collisions in all crash severities and thus revealed information beyond what is available in, for example, data sets of police-reported crashes. This will guide further development of driver support systems. For crashes with repair cost exceeding US$1,250, a significant crash reduction was found, although the technology did not significantly reduce the total number of lane change crashes. An average lower insurance claim cost for cars equipped with the BLIS technology also indicated that the technology contributes to reduced crash severity even if crashes were not totally avoided. Stratifying the data into different lane change crash situations gave indications of the condition-specific performance of the system, even if the results were not statistically significant at the 95% level.

Comparative Study of 3-Dimensional Woven Joint Architectures for Composite Spacecraft Structures

NASA Technical Reports Server (NTRS)

Jones, Justin S.; Polis, Daniel L.; Rowles, Russell R.; Segal, Kenneth N.

2011-01-01

The National Aeronautics and Space Administration (NASA) Exploration Systems Mission Directorate initiated an Advanced Composite Technology (ACT) Project through the Exploration Technology Development Program in order to support the polymer composite needs for future heavy lift launch architectures. As an example, the large composite structural applications on Ares V inspired the evaluation of advanced joining technologies, specifically 3D woven composite joints, which could be applied to segmented barrel structures needed for autoclave cured barrel segments due to autoclave size constraints. Implementation of these 3D woven joint technologies may offer enhancements in damage tolerance without sacrificing weight. However, baseline mechanical performance data is needed to properly analyze the joint stresses and subsequently design/down-select a preform architecture. Six different configurations were designed and prepared for this study; each consisting of a different combination of warp/fill fiber volume ratio and preform interlocking method (Z-fiber, fully interlocked, or hybrid). Tensile testing was performed for this study with the enhancement of a dual camera Digital Image Correlation (DIC) system which provides the capability to measure full-field strains and three dimensional displacements of objects under load. As expected, the ratio of warp/fill fiber has a direct influence on strength and modulus, with higher values measured in the direction of higher fiber volume bias. When comparing the Z-fiber weave to a fully interlocked weave with comparable fiber bias, the Z-fiber weave demonstrated the best performance in two different comparisons. We report the measured tensile strengths and moduli for test coupons from the 6 different weave configurations under study.

Evaluation of Solid Modeling Software for Finite Element Analysis of Woven Ceramic Matrix Composites

NASA Technical Reports Server (NTRS)

Nemeth, Noel N.; Mital, Subodh; Lang, Jerry

2010-01-01

Three computer programs, used for the purpose of generating 3-D finite element models of the Repeating Unit Cell (RUC) of a textile, were examined for suitability to model woven Ceramic Matrix Composites (CMCs). The programs evaluated were the open-source available TexGen, the commercially available WiseTex, and the proprietary Composite Material Evaluator (COMATE). A five-harness-satin (5HS) weave for a melt-infiltrated (MI) silicon carbide matrix and silicon carbide fiber was selected as an example problem and the programs were tested for their ability to generate a finite element model of the RUC. The programs were also evaluated for ease-of-use and capability, particularly for the capability to introduce various defect types such as porosity, ply shifting, and nesting of a laminate. Overall, it was found that TexGen and WiseTex were useful for generating solid models of the tow geometry; however, there was a lack of consistency in generating well-conditioned finite element meshes of the tows and matrix. TexGen and WiseTex were both capable of allowing collective and individual shifting of tows within a ply and WiseTex also had a ply nesting capability. TexGen and WiseTex were sufficiently userfriendly and both included a Graphical User Interface (GUI). COMATE was satisfactory in generating a 5HS finite element mesh of an idealized weave geometry but COMATE lacked a GUI and was limited to only 5HS and 8HS weaves compared to the larger amount of weave selections available with TexGen and WiseTex.

Biomolecular Evidence of Silk from 8,500 Years Ago

PubMed Central

Gong, Yuxuan; Li, Li; Gong, Decai; Yin, Hao; Zhang, Juzhong

2016-01-01

Pottery, bone implements, and stone tools are routinely found at Neolithic sites. However, the integrity of textiles or silk is susceptible to degradation, and it is therefore very difficult for such materials to be preserved for 8,000 years. Although previous studies have provided important evidence of the emergence of weaving skills and tools, such as figuline spinning wheels and osseous lamellas with traces of filament winding, there is a lack of direct evidence proving the existence of silk. In this paper, we explored evidence of prehistoric silk fibroin through the analysis of soil samples collected from three tombs at the Neolithic site of Jiahu. Mass spectrometry was employed and integrated with proteomics to characterize the key peptides of silk fibroin. The direct biomolecular evidence reported here showed the existence of prehistoric silk fibroin, which was found in 8,500-year-old tombs. Rough weaving tools and bone needles were also excavated, indicating the possibility that the Jiahu residents may possess the basic weaving and sewing skills in making textile. This finding may advance the study of the history of silk, and the civilization of the Neolithic Age. PMID:27941996

Twofold orthogonal weavings on cuboids

PubMed Central

Kovács, Flórián

2016-01-01

Some closed polyhedral surfaces can be completely covered by two-way, twofold (rectangular) weaving of strands of constant width. In this paper, a construction for producing all possible geometries for such weavable cuboids is proposed: a theorem on spherical octahedra is proven first that all further theory is based on. The construction method of weavable cuboids itself relies on successive truncations of an initial tetrahedron and is also extended for cases of degenerate (unbounded) polyhedra. Arguments are mainly based on the plane geometry of the development of the respective polyhedra, in connection with some of three-dimensional projective properties of the same. PMID:27118910

The geometry of periodic knots, polycatenanes and weaving from a chemical perspective: a library for reticular chemistry.

PubMed

Liu, Yuzhong; O'Keeffe, Michael; Treacy, Michael M J; Yaghi, Omar M

2018-05-04

The geometry of simple knots and catenanes is described using the concept of linear line segments (sticks) joined at corners. This is extended to include woven linear threads as members of the extended family of knots. The concept of transitivity that can be used as a measure of regularity is explained. Then a review is given of the simplest, most 'regular' 2- and 3-periodic patterns of polycatenanes and weavings. Occurrences in crystal structures are noted but most structures are believed to be new and ripe targets for designed synthesis.

The ING observatory in the 2015-2025 decade

NASA Astrophysics Data System (ADS)

Balcells, M.

2015-05-01

The Isaac Newton Group, after nearly 30 years of productive operation of the William Herschel, Isaac Newton and Jacobus Kapteyn telescopes, is reviewing its science focus. The central goal is to respond to the changes in the astronomical landscapes in UK, the Netherlands, and especially in Spain, now a mature world-player community with access to 10-m class telescopes on La Palma and Paranal. The current model, which exploits scientific and instrumentation diversity, will continue to be offered until 2017. In the meantime, an ING-led consortium is building WEAVE, a next-generation spectroscopic facility for the WHT. WEAVE is a multi-fibre system capable of deploying either 1000 single-fibre probes, 25 mini-IFUs or a single large IFU, to feed a two-arm bench spectrograph which delivers resolving powers of either 5000 or 20,000. WEAVE will exploit a new field corrector at the WHT that enlarges the prime-focus FOV diameter from the current 40 arcmin to 2 degrees. WEAVE will be used to carry out massive surveys that exploit Gaia data in topics of Milky Way astronomy and stellar evolution; surveys that carry out galaxy evolution studies linked to various multi-wavelength surveys, including the LOFAR radio telescope; and redshift surveys of distant galaxies for cosmology. Community fibres will be available. The expectation is that these surveys will use 70% of the WHT time until at least 2022. The rest of the time will be available via normal TAC allocations, for use of facility instrumentation. Plans for the INT include involving external institutions in the provision of new instrumentation and/or telescope upgrades in exchange for significant fractions of telescope time.

Effect of natural fiber types and sodium silicate coated on natural fiber mat/PLA composites: Tensile properties and rate of fire propagation

NASA Astrophysics Data System (ADS)

Thongpin, C.; Srimuk, J.; hipkam, N.; Wachirapong, P.

2015-07-01

In this study, 3 types of natural fibres, i.e. jute, sisal and abaca, were plain weaved to fibre mat. Before weaving, the fibres were treated with 5% NaOH to remove hemi cellulose and lignin. The weaving was performed by hand using square wooden block fit with nails for weaving using one and two types of natural fibres as weft and warp fibre to produce natural fibre mat. The fibre mat was also impregnated in sodium silicate solution extracted from rich husk ash. The pH of the solution was adjusted to pH 7 using H2SO4 before impregnation. After predetermined time, sodium silicate was gelled and deposited on the mat. The fabric mat and sodium silicate coated mat were then impregnated with PLA solution to produce prepreg. Dried pepreg was laminated with PLA sheet using compressing moulding machine to obtain natural fibre mat/PLA composite. The composite containing abaca aligned in longitudinal direction with respect to tension force enhanced Young's modulus more than 300%. Fibre mat composites with abaca aligned in longitudinal direction also showed tensile strength enhancement nearly 400% higher than neat PLA. After coating with sodium silicate, the tensile modulus of the composites was found slightly increased. The silicate coating was disadvantage on tensile strength of the composite due to the effect of sodium hydroxide solution that was used as solvent for silicate extraction from rice husk ash. However, sodium silicate could retard rate of fire propagation about 50%compare to neat PLA and about 10% reduction compared to fibre mat composites without sodium silicate coated fibre mat.

Textile Technologies and Tissue Engineering: A Path Towards Organ Weaving

PubMed Central

Akbari, Mohsen; Tamayol, Ali; Bagherifard, Sara; Serex, Ludovic; Mostafalu, Pooria; Faramarzi, Negar; Mohammadi, Mohammad Hossein

2016-01-01

Textile technologies have recently attracted great attention as potential biofabrication tools for engineering tissue constructs. Using current textile technologies, fibrous structures can be designed and engineered to attain the required properties that are demanded by different tissue engineering applications. Several key parameters such as physiochemical characteristics of fibers, pore size and mechanical properties of the fabrics play important role in the effective use of textile technologies in tissue engineering. This review summarizes the current advances in the manufacturing of biofunctional fibers. Different textile methods such as knitting, weaving, and braiding are discussed and their current applications in tissue engineering are highlighted. PMID:26924450

Thermal-Mechanical Response of Cracked Satin Weave CFRP Composites at Cryogenic Temperatures

NASA Astrophysics Data System (ADS)

Watanabe, S.; Shindo, Y.; Narita, F.; Takeda, T.

2008-03-01

This paper examines the thermal-mechanical response of satin weave carbon fiber reinforced polymer (CFRP) laminates with internal and/or edge cracks subjected to uniaxial tension load at cryogenic temperatures. Cracks are considered to occur in the transverse fiber bundles and extend through the entire thickness of the fiber bundles. Two-dimentional generalized plane strain finite element models are developed to study the effects of residual thermal stresses and cracks on the mechanical behavior of CFRP woven laminates. A detailed examination of the Young's modulus and stress distributions near the crack tip is carried out which provides insight into material behavior at cryogenic temperatures.

The effect of fibre orientation on a TWCP composite

NASA Astrophysics Data System (ADS)

Barnes, N. R.; Hughes, A.; Wood, D. C.; Appleby-Thomas, G. J.; Leighs, J. A.; Goff, M.; Hazell, P. J.

2014-05-01

Multiple authors have shown that orientation can greatly affect the shock profiles seen in composites. Carbon fibre composites are employed in multiple sectors, with their use in the aerospace industry becoming more prevalent. An angle of 20° between the outer surface and the weave direction has been shown to provide a good compromise between strength and ablation, making orientation an important property. Using a single stage gas gun with manganin pressure gauges the shock response of both a 90° and 45° layup TWCP composite was investigated up to a particle velocity of approximately 1 mm μs-1, in both the Us-up and pressure-volume planes. Comparisons in terms of shock propagation were also made with a previously investigated TWCP orientation of 0° . This allowed a detailed interrogation of the effects of weave orientation in this important TWCP composite to be made. It was found that the shock response was not greatly altered by orientation of the carbon fibre weave above a certain particle velocity. This was due to the 90° behaving elastically until a particle velocity of 0.6 mm μs-1. Above this value the experimental data had very little deviation regardless of the angle.

The Impact of Ergonomically Designed Workstations on Shoulder EMG Activity during Carpet Weaving

PubMed Central

Motamedzade, Majid; Afshari, Davood; Soltanian, Alireza

2014-01-01

Background: The present study aimed to evaluate the biomechanical exposure to the trapezius muscle activity in female weavers for a prolonged period in the workstation A (suggested by previous studies) and workstation B (proposed by the present study). Methods: Electromyography data were collected from nine females during four hours for each ergonomically designed workstation at the Ergonomics Laboratory, Hamadan, Iran. The design criteria for ergonomically designed workstations were: 1) weaving height (20 and 3 cm above elbow height for workstations A and B, respectively), and 2) seat type (10° and 0° forwardsloping seat for workstations A and B, respectively). Results: The amplitude probability distribution function (APDF) analysis showed that the left and right upper trapezius muscle activity was almost similar at each workstation. Trapezius muscle activity in the workstation A was signifi­cantly greater than workstations B (P<0.001). Conclusion: In general, use of workstation B leads to significantly reduced muscle activity levels in the upper trapezius as compared to workstation A in weavers. Despite the positive impact of workstation B in reducing trapezius muscle activity, it seems that constrained postures of the upper arm during weaving may be associated with musculoskeletal symptoms. PMID:25650180

The Impact of Ergonomically Designed Workstations on Shoulder EMG Activity during Carpet Weaving.

PubMed

Motamedzade, Majid; Afshari, Davood; Soltanian, Alireza

2014-01-01

The present study aimed to evaluate the biomechanical exposure to the trapezius muscle activity in female weavers for a prolonged period in the workstation A (suggested by previous studies) and workstation B (proposed by the present study). Electromyography data were collected from nine females during four hours for each ergonomically designed workstation at the Ergonomics Laboratory, Hamadan, Iran. The design criteria for ergonomically designed workstations were: 1) weaving height (20 and 3 cm above elbow height for workstations A and B, respectively), and 2) seat type (10° and 0° forwardsloping seat for workstations A and B, respectively). The amplitude probability distribution function (APDF) analysis showed that the left and right upper trapezius muscle activity was almost similar at each workstation. Trapezius muscle activity in the workstation A was signifi-cantly greater than workstations B (P<0.001). In general, use of workstation B leads to significantly reduced muscle activity levels in the upper trapezius as compared to workstation A in weavers. Despite the positive impact of workstation B in reducing trapezius muscle activity, it seems that constrained postures of the upper arm during weaving may be associated with musculoskeletal symptoms.

Weaving for heart valve tissue engineering.

PubMed

Liberski, Albert; Ayad, Nadia; Wojciechowska, Dorota; Kot, Radoslaw; Vo, Duy M P; Aibibu, Dilibaier; Hoffmann, Gerald; Cherif, Chokri; Grobelny-Mayer, Katharina; Snycerski, Marek; Goldmann, Helmut

2017-11-01

Weaving is a resourceful technology which offers a large selection of solutions that are readily adaptable for tissue engineering (TE) of artificial heart valves (HV). The different ways that the yarns are interlaced in this technique could be used to produce complex architectures, such as the three-layer architecture of the leaflets. Once the assembly is complete, growth of cells in the scaffold would occur in the orientation of the yarn, enabling the deposition of extra cellular matrixes proteins in an oriented manner. Weaving technology is a rapidly evolving field that, first, needs to be understood, and then explored by tissue engineers, so that it could be used to create efficient scaffolds. Similarly, the textile engineers need to gain a basic understanding of key structural and mechanical aspects of the heart valve. The aim of this review is to provide the platform for joining these two fields and to enable cooperative research efforts. Moreover, examples of woven medical products and patents as well as related publication are discussed in this review, nevertheless due to the large, and continuously growing volume of data, only the aspects strictly associated with HVTE lay in the scope of this paper. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of fiber architecture on flexural characteristics and fracture of fiber-reinforced dental composites.

PubMed

Karbhari, Vistasp M; Strassler, Howard

2007-08-01

The aim of this study was to compare and elucidate the differences in damage mechanisms and response of fiber-reinforced dental resin composites based on three different brands under flexural loading. The types of reinforcement consisted of a unidirectional E-glass prepreg (Splint-It from Jeneric/Petron Inc.), an ultrahigh molecular weight polyethylene fiber based biaxial braid (Connect, Kerr) and an ultrahigh molecular weight polyethylene fiber based leno-weave (Ribbond). Three different commercially available fiber reinforcing systems were used to fabricate rectangular bars, with the fiber reinforcement close to the tensile face, which were tested in flexure with an emphasis on studying damage mechanisms and response. Eight specimens (n=8) of each type were tested. Overall energy capacity as well as flexural strength and modulus were determined and results compared in light of the different abilities of the architectures used. Under flexural loading unreinforced and unidirectional prepreg reinforced dental composites failed in a brittle fashion, whereas the braid and leno-weave reinforced materials underwent significant deformation without rupture. The braid reinforced specimens showed the highest peak load. The addition of the unidirectional to the matrix resulted in an average strain of 0.06mm/mm which is 50% greater than the capacity of the unreinforced matrix, whereas the addition of the braid and leno-weave resulted in increases of 119 and 126%, respectively, emphasizing the higher capacity of both the UHM polyethylene fibers and the architectures to hold together without rupture under flexural loading. The addition of the fiber reinforcement substantially increases the level of strain energy in the specimens with the maximum being attained in the braid reinforced specimens with a 433% increase in energy absorption capability above the unreinforced case. The minimum scatter and highest consistency in response is seen in the leno-weave reinforced specimens due to the details of the architecture which restrict fabric shearing and movement during placement. It is crucial that the appropriate selection of fiber architectures be made not just from a perspective of highest strength, but overall damage tolerance and energy absorption. Differences in weaves and architectures can result in substantially different performance and appropriate selection can mitigate premature and catastrophic failure. The study provides details of materials level response characteristics which are useful in selection of the fiber reinforcement based on specifics of application.

Acute and subchronic effects of bilastine (20 and 40 mg) and hydroxyzine (50 mg) on actual driving performance in healthy volunteers.

PubMed

Conen, Silke; Theunissen, Eef L; Van Oers, Anita C M; Valiente, Román; Ramaekers, Johannes G

2011-11-01

Bilastine is a new second-generation H1 antagonist. Although bilastine has been demonstrated to produce little or no performance impairment in laboratory tests, it cannot be excluded that it produces impairments in real-life performance such as driving. This study aims to assess the effects of two doses of bilastine (20 and 40 mg) on actual driving after single and repeated administration. Hydroxyzine 50 mg was included as an active control. Twenty-two participants (11 females, 11 males) were tested in a placebo-controlled, randomized, double-blind, four-way cross-over design. Participants were treated with once-daily doses for eight consecutive days. On day 1 and 8 of each treatment period participants performed an actual highway driving test. The primary variable was standard deviation of lateral position (SDLP), a measure of weaving. Results demonstrated that hydroxyzine significantly increased SDLP on days 1 and 8 of treatment. Bilastine did not affect SDLP. It is concluded that hydroxyzine produces severe driving impairment after single doses and that this impairment only partly mitigates over time due to a lack of complete tolerance. Bilastine did not produce any driving impairment after single and repeated doses and can be safely used in traffic in doses up to 40 mg.

Creep of plain weave polymer matrix composites

NASA Astrophysics Data System (ADS)

Gupta, Abhishek

Polymer matrix composites are increasingly used in various industrial sectors to reduce structural weight and improve performance. Woven (also known as textile) composites are one class of polymer matrix composites with increasing market share mostly due to their lightweight, their flexibility to form into desired shape, their mechanical properties and toughness. Due to the viscoelasticity of the polymer matrix, time-dependent degradation in modulus (creep) and strength (creep rupture) are two of the major mechanical properties required by engineers to design a structure reliably when using these materials. Unfortunately, creep and creep rupture of woven composites have received little attention by the research community and thus, there is a dire need to generate additional knowledge and prediction models, given the increasing market share of woven composites in load bearing structural applications. Currently, available creep models are limited in scope and have not been validated for any loading orientation and time period beyond the experimental time window. In this thesis, an analytical creep model, namely the Modified Equivalent Laminate Model (MELM), was developed to predict tensile creep of plain weave composites for any orientation of the load with respect to the orientation of the fill and warp fibers, using creep of unidirectional composites. The ability of the model to predict creep for any orientation of the load is a "first" in this area. The model was validated using an extensive experimental involving the tensile creep of plain weave composites under varying loading orientation and service conditions. Plain weave epoxy (F263)/ carbon fiber (T300) composite, currently used in aerospace applications, was procured as fabrics from Hexcel Corporation. Creep tests were conducted under two loading conditions: on-axis loading (0°) and off-axis loading (45°). Constant load creep, in the temperature range of 80-240°C and stress range of 1-70% UTS of the composites, was experimentally evaluated for time periods ranging from 1--120 hours under both loading conditions. The composite showed increase in creep with increase in temperature and stress. Creep of composite increased with increase in angle of loading, from 1% under on-axis loading to 31% under off-axis loading, within the tested time window. The experimental creep data for plain weave composites were superposed using TTSP (Time Temperature Superposition Principle) to obtain a master curve of experimental data extending to several years and was compared with model predictions to validate the model. The experimental and model results were found in good agreement within an error range of +/-1-3% under both loading conditions. A parametric study was also conducted to understand the effect of microstructure of plain weave composites on its on-axis and off-axis creep. Generation of knowledge in this area is also "first". Additionally, this thesis generated knowledge on time-dependent damage m woven composites and its effect on creep and tensile properties and their prediction.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruvinsky, Anatoly M., E-mail: anatoly.ruvinsky@astrazeneca.com; Center for Bioinformatics, The University of Kansas, Lawrence, Kansas 66047; Vakser, Ilya A.

Ferritin-like molecules show a remarkable combination of the evolutionary conserved activity of iron uptake and release that engage different pores in the conserved ferritin shell. It was hypothesized that pore selection and iron traffic depend on dynamic allostery with no conformational changes in the backbone. In this study, we detect the allosteric networks in Pseudomonas aeruginosa bacterioferritin (BfrB), bacterial ferritin (FtnA), and bullfrog M and L ferritins (Ftns) by a network-weaving algorithm (NWA) that passes threads of an allosteric network through highly correlated residues using hierarchical clustering. The residue-residue correlations are calculated in the packing-on elastic network model that introducesmore » atom packing into the common packing-off model. Applying NWA revealed that each of the molecules has an extended allosteric network mostly buried inside the ferritin shell. The structure of the networks is consistent with experimental observations of iron transport: The allosteric networks in BfrB and FtnA connect the ferroxidase center with the 4-fold pores and B-pores, leaving the 3-fold pores unengaged. In contrast, the allosteric network directly links the 3-fold pores with the 4-fold pores in M and L Ftns. The majority of the network residues are either on the inner surface or buried inside the subunit fold or at the subunit interfaces. We hypothesize that the ferritin structures evolved in a way to limit the influence of functionally unrelated events in the cytoplasm on the allosteric network to maintain stability of the translocation mechanisms. We showed that the residue-residue correlations and the resultant long-range cooperativity depend on the ferritin shell packing, which, in turn, depends on protein sequence composition. Switching from the packing-on to the packing-off model reduces correlations by 35%–38% so that no allosteric network can be found. The influence of the side-chain packing on the allosteric networks explains the diversity in mechanisms of iron traffic suggested by experimental approaches.« less

Weaving child psychoanalysis: Past, present, and future.

PubMed

Brinich, Paul M

2013-01-01

Using the metaphor of a fabric woven from many threads, this paper describes nine of the many conceptual strands that have contributed to the development of child psychoanalysis over its first century. It notes the unfortunate isolation (sometimes self-imposed) of child analysis from related fields (including adult analysis) and argues that we must recognize both the strengths and weaknesses of our psychoanalytic tools if we are to collaborate with and profit from the work of nonanalytic colleagues. It closes with the suggestion that the continued weaving of child analysis will require the creation of new looms, structures that are able to support a new generation of child analysts and the continued elaboration of the field.

Towards an Integrated Model of the WEAVE Performance

NASA Astrophysics Data System (ADS)

Ham, S. J.; Dalton, G.

2016-10-01

WEAVE is a new facility instrument for the 4.2 m William Herschel Telescope (WHT). The instrument has a 2° field of view and covers a wavelength range of 366-950 nm with up to 960 simultaneous spectra in each observation. The spectrograph consists of a collimator mirror and two correcting lenses before a VPH grating and two 8-lens cameras. The two cameras have been designed to have the same lens shapes. Here we report on the development of detailed simulations for the verification of the whole data reduction procedure and analysis pipeline, and for the generation of high signal-to-noise reference images that can be used as fitting templates for fiber positions and PSF mapping.

Verification of Commercial Motor Performance for WEAVE at the William Herschel Telescope

NASA Astrophysics Data System (ADS)

Gilbert, J.; Dalton, G.; Lewis, I.

2016-10-01

WEAVE is a 1000-fiber multi-object spectroscopic facility for the 4.2 m William Herschel Telescope. It will feature a double-headed pick-and-place fiber positioning robot comprising commercially available robotic axes. This paper presents results on the performance of these axes, obtained by testing a prototype system in the laboratory. Positioning accuracy is found to be better than the manufacturer's published values for the tested cases, indicating that the requirement for a maximum positioning error of 8.0 microns is achievable. Field reconfiguration times well within the planned 60 minute observation window are shown to be likely when individual axis movements are combined in an efficient way.

The male of the orb-weaving spider Plebs mitratus (Simon, 1895) and a redescription of the female (Araneae, Araneidae).

PubMed

Paul, Jimmy; Sankaran, Pradeep M; Joseph, Mathew M; Sebastian, Pothalil A

2016-10-28

The orb-weaving spider genus Plebs Joseph & Framenau, 2012 currently has only two representatives in India: Plebs himalayaensis (Tikader, 1975) from the Himalayas and Plebs mitratus (Simon, 1895) from the Nilgiris and Anamudi Shola National Park (World Spider Catalog 2016), both are found in high altitude mountainous habitats (Joseph & Framenau 2012). Both species were known only from females (World Spider Catalog 2016), although Sherriffs (1918, 1919) provided a description of an immature male of P. mitratus. In the present paper, we provide the first description of the adult male of P. mitratus, together with the detailed redescription of its female demonstrating considerable intraspecific variation.

Notes on the orb-weaving spider genus Alpaida (Araneae, Araneidae) with description of four new species from Rio de Janeiro, Brazil.

PubMed

Baptista, Renner Luiz Cerqueira; De Souza Castanheira, Pedro; Prado, AndrÉ Wanderley do

2018-04-11

Four new species of the orb-weaving spider genus Alpaida O. P.-Cambridge, 1889 from Rio de Janeiro state, Brazil are illustrated and described based on males and females from the following municipalities: Alpaida imperatrix new species (Macaé and Rio de Janeiro); Alpaida imperialis new species (Mendes and Rio de Janeiro); Alpaida marista new species (Mendes and Pinheiral); and Alpaida mendensis new species (Mendes). Furthermore, two new synonymies are herein proposed: Alpaida lanei Levi, 1988 = Alpaida atomaria (Simon, 1895) and Alpaida caxias Levi, 1988 = Alpaida tijuca Levi, 1988, alongside new records for both species and also Alpaida venger Castanheira Baptista, 2015.

Pressure Drop Across Woven Screens Under Uniform and Nonuniform Flow Conditions. [flow characteristics of water through Dutch twill and square weave fabrics

NASA Technical Reports Server (NTRS)

Ludewig, M.; Omori, S.; Rao, G. L.

1974-01-01

Tests were conducted to determine the experimental pressure drop and velocity data for water flowing through woven screens. The types of materials used are dutch twill and square weave fabrics. Pressure drop measures were made at four locations in a rectangular channel. The data are presented as change in pressure compared with the average entry velocity and the numerical relationship is determined by dividing the volumetric flow rate by the screen area open to flow. The equations of continuity and momentum are presented. A computer program listing an extension of a theoretical model and data from that computer program are included.

Textile Technologies and Tissue Engineering: A Path Toward Organ Weaving.

PubMed

Akbari, Mohsen; Tamayol, Ali; Bagherifard, Sara; Serex, Ludovic; Mostafalu, Pooria; Faramarzi, Negar; Mohammadi, Mohammad Hossein; Khademhosseini, Ali

2016-04-06

Textile technologies have recently attracted great attention as potential biofabrication tools for engineering tissue constructs. Using current textile technologies, fibrous structures can be designed and engineered to attain the required properties that are demanded by different tissue engineering applications. Several key parameters such as physiochemical characteristics of fibers, microarchitecture, and mechanical properties of the fabrics play important roles in the effective use of textile technologies in tissue engineering. This review summarizes the current advances in the manufacturing of biofunctional fibers. Different textile methods such as knitting, weaving, and braiding are discussed and their current applications in tissue engineering are highlighted. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Scale-up of nature's tissue weaving algorithms to engineer advanced functional materials.

PubMed

Ng, Joanna L; Knothe, Lillian E; Whan, Renee M; Knothe, Ulf; Tate, Melissa L Knothe

2017-01-11

We are literally the stuff from which our tissue fabrics and their fibers are woven and spun. The arrangement of collagen, elastin and other structural proteins in space and time embodies our tissues and organs with amazing resilience and multifunctional smart properties. For example, the periosteum, a soft tissue sleeve that envelops all nonarticular bony surfaces of the body, comprises an inherently "smart" material that gives hard bones added strength under high impact loads. Yet a paucity of scalable bottom-up approaches stymies the harnessing of smart tissues' biological, mechanical and organizational detail to create advanced functional materials. Here, a novel approach is established to scale up the multidimensional fiber patterns of natural soft tissue weaves for rapid prototyping of advanced functional materials. First second harmonic generation and two-photon excitation microscopy is used to map the microscopic three-dimensional (3D) alignment, composition and distribution of the collagen and elastin fibers of periosteum, the soft tissue sheath bounding all nonarticular bone surfaces in our bodies. Then, using engineering rendering software to scale up this natural tissue fabric, as well as multidimensional weaving algorithms, macroscopic tissue prototypes are created using a computer-controlled jacquard loom. The capacity to prototype scaled up architectures of natural fabrics provides a new avenue to create advanced functional materials.

Scale-up of nature’s tissue weaving algorithms to engineer advanced functional materials

NASA Astrophysics Data System (ADS)

Ng, Joanna L.; Knothe, Lillian E.; Whan, Renee M.; Knothe, Ulf; Tate, Melissa L. Knothe

2017-01-01

We are literally the stuff from which our tissue fabrics and their fibers are woven and spun. The arrangement of collagen, elastin and other structural proteins in space and time embodies our tissues and organs with amazing resilience and multifunctional smart properties. For example, the periosteum, a soft tissue sleeve that envelops all nonarticular bony surfaces of the body, comprises an inherently “smart” material that gives hard bones added strength under high impact loads. Yet a paucity of scalable bottom-up approaches stymies the harnessing of smart tissues’ biological, mechanical and organizational detail to create advanced functional materials. Here, a novel approach is established to scale up the multidimensional fiber patterns of natural soft tissue weaves for rapid prototyping of advanced functional materials. First second harmonic generation and two-photon excitation microscopy is used to map the microscopic three-dimensional (3D) alignment, composition and distribution of the collagen and elastin fibers of periosteum, the soft tissue sheath bounding all nonarticular bone surfaces in our bodies. Then, using engineering rendering software to scale up this natural tissue fabric, as well as multidimensional weaving algorithms, macroscopic tissue prototypes are created using a computer-controlled jacquard loom. The capacity to prototype scaled up architectures of natural fabrics provides a new avenue to create advanced functional materials.

Flexible Elements in the Mechanisms of Weaving Machines

NASA Astrophysics Data System (ADS)

Žák, J.

Weaving machines use several mechanisms to produce a fabric; their relative (mutual) position is exactly defined at any point of working cycle and must be maintained as accurately as possible. From that, it results some requirements on their design, such as stiffness of the joint frame, synchronization of their drives, accuracy and stiffness of particular links of those mechanisms and minimization of the clearances between them. In this paper, we have attempted to outline the possibility of replacing the binary links by using the flexible mechanism elements. In this step, we always removed one rotary constraint at least which is necessary when using a binary link, i.e., a rod, pitman or connecting rod. In practice, it means reducing the number of bearings which have a limited service life, require maintenance and when using them we cannot avoid the formation of clearances. In the case of a slay of the CAMEL weaving machine, it was furthermore possible to use the deformation energy to a relief of the drive, its better regulation and an overall reduction of energy consumption. Although this procedure is not subject to the use of special materials, there can be advantageously used fiber composites whose certain features make the design of such mechanisms easy to a great extent.

Harvesting Energy from the Counterbalancing (Weaving) Movement in Bicycle Riding

PubMed Central

Yang, Yoonseok; Yeo, Jeongjin; Priya, Shashank

2012-01-01

Bicycles are known to be rich source of kinetic energy, some of which is available for harvesting during speedy and balanced maneuvers by the user. A conventional dynamo attached to the rim can generate a large amount of output power at an expense of extra energy input from the user. However, when applying energy conversion technology to human powered equipments, it is important to minimize the increase in extra muscular activity and to maximize the efficiency of human movements. This study proposes a novel energy harvesting methodology that utilizes lateral oscillation of bicycle frame (weaving) caused by user weight shifting movements in order to increase the pedaling force in uphill riding or during quick speed-up. Based on the 3D motion analysis, we designed and implemented the prototype of an electro-dynamic energy harvester that can be mounted on the bicycle's handlebar to collect energy from the side-to-side movement. The harvester was found to generate substantial electric output power of 6.6 mW from normal road riding. It was able to generate power even during uphill riding which has never been shown with other approaches. Moreover, harvesting of energy from weaving motion seems to increase the economy of cycling by helping efficient usage of human power. PMID:23112598

Harvesting energy from the counterbalancing (weaving) movement in bicycle riding.

PubMed

Yang, Yoonseok; Yeo, Jeongjin; Priya, Shashank

2012-01-01

Bicycles are known to be rich source of kinetic energy, some of which is available for harvesting during speedy and balanced maneuvers by the user. A conventional dynamo attached to the rim can generate a large amount of output power at an expense of extra energy input from the user. However, when applying energy conversion technology to human powered equipments, it is important to minimize the increase in extra muscular activity and to maximize the efficiency of human movements. This study proposes a novel energy harvesting methodology that utilizes lateral oscillation of bicycle frame (weaving) caused by user weight shifting movements in order to increase the pedaling force in uphill riding or during quick speed-up. Based on the 3D motion analysis, we designed and implemented the prototype of an electro-dynamic energy harvester that can be mounted on the bicycle's handlebar to collect energy from the side-to-side movement. The harvester was found to generate substantial electric output power of 6.6 mW from normal road riding. It was able to generate power even during uphill riding which has never been shown with other approaches. Moreover, harvesting of energy from weaving motion seems to increase the economy of cycling by helping efficient usage of human power.

Duplication and concerted evolution of MiSp-encoding genes underlie the material properties of minor ampullate silks of cobweb weaving spiders.

PubMed

Vienneau-Hathaway, Jannelle M; Brassfield, Elizabeth R; Lane, Amanda Kelly; Collin, Matthew A; Correa-Garhwal, Sandra M; Clarke, Thomas H; Schwager, Evelyn E; Garb, Jessica E; Hayashi, Cheryl Y; Ayoub, Nadia A

2017-03-14

Orb-web weaving spiders and their relatives use multiple types of task-specific silks. The majority of spider silk studies have focused on the ultra-tough dragline silk synthesized in major ampullate glands, but other silk types have impressive material properties. For instance, minor ampullate silks of orb-web weaving spiders are as tough as draglines, due to their higher extensibility despite lower strength. Differences in material properties between silk types result from differences in their component proteins, particularly members of the spidroin (spider fibroin) gene family. However, the extent to which variation in material properties within a single silk type can be explained by variation in spidroin sequences is unknown. Here, we compare the minor ampullate spidroins (MiSp) of orb-weavers and cobweb weavers. Orb-web weavers use minor ampullate silk to form the auxiliary spiral of the orb-web while cobweb weavers use it to wrap prey, suggesting that selection pressures on minor ampullate spidroins (MiSp) may differ between the two groups. We report complete or nearly complete MiSp sequences from five cobweb weaving spider species and measure material properties of minor ampullate silks in a subset of these species. We also compare MiSp sequences and silk properties of our cobweb weavers to published data for orb-web weavers. We demonstrate that all our cobweb weavers possess multiple MiSp loci and that one locus is more highly expressed in at least two species. We also find that the proportion of β-spiral-forming amino acid motifs in MiSp positively correlates with minor ampullate silk extensibility across orb-web and cobweb weavers. MiSp sequences vary dramatically within and among spider species, and have likely been subject to multiple rounds of gene duplication and concerted evolution, which have contributed to the diverse material properties of minor ampullate silks. Our sequences also provide templates for recombinant silk proteins with tailored properties.

Ballistic damage in hybrid composite laminates

NASA Astrophysics Data System (ADS)

Phadnis, Vaibhav A.; Pandya, Kedar S.; Naik, Niranjan K.; Roy, Anish; Silberschmidt, Vadim V.

2015-07-01

Ballistic damage of hybrid woven-fabric composites made of plain-weave E-glass- fabric/epoxy and 8H satin-weave T300 carbon-fabric/epoxy is studied using a combination of experimental tests, microstructural studies and finite-element (FE) analysis. Ballistic tests were conducted with a single-stage gas gun. Fibre damage and delamination were observed to be dominating failure modes. A ply-level FE model was developed, with a fabric-reinforced ply modelled as a homogeneous orthotropic material with capacity to sustain progressive stiffness degradation due to fibre/matrix cracking, fibre breaking and plastic deformation under shear loading. Simulated damage patterns on the front and back faces of fabric-reinforced composite plates provided an insight into their damage mechanisms under ballistic loading.

Roughness induced transition and heat transfer augmentation in hypersonic environments

NASA Astrophysics Data System (ADS)

Wassel, A. T.; Shih, W. C. L.; Courtney, J. F.

Boundary layer transition and surface heating distributions on graphite, fine weave carbon-carbon, and metallic nosetip materials were derived from surface temperature responses measured in nitrogen environments during both free-flight and track-guided testing in hypersonic environments. Innovative test procedures were developed, and heat transfer results were validated against established theory through experiments using a super-smooth tungsten model. Quantitative definitions of mean transition front locations were established by deriving heat flux distributions from measured temperatures, and comparisons made with existing nosetip transition correlations. Qualitative transition locations were inferred directly from temperature distributions to investigate preferred orientations on fine weave nosetips. Levels of roughness augmented heat transfer were generally shown to be below values predicted by state-of-the-art methods.

Ploy and counterploy in predator-prey interactions: Orb-weaving spiders versus bombardier beetles*

PubMed Central

Eisner, Thomas; Dean, Jeffrey

1976-01-01

Bombardier beetles (Brachinus spp.) offered to orb-weaving spiders are either captured or lost, depending on the attack strategy of the spider. Nephila clavipes grasps a beetle directly and attempts to bite it outright, but is repelled by the beetle's defensive spray. As the spider recovers from the spray, the beetle makes its escape from the web. Argiope first imprisons the beetle by wrapping it delicately in silk, without causing it to spray. When the spider then proceeds to bite, the wrapping protects it against the full effects of the spray. The wrapping strategy may be generally effective against chemically protected insects, and it is suggested that this may be one of its principal adaptive justifications. Images PMID:16592308

Isotropy equilibrium of the double woven fabric with cotton face and wool reverse fibrous compositions

NASA Astrophysics Data System (ADS)

Rahnev, I.; Rimini, G.

2017-10-01

The equilibrium of the masses and the mechanical properties between the warp and the weft is a determining factor for the quality of the woven fabrics. When the fabric has a multi-layered structure and is designed for protective clothing, the uniform distribution of the elastical resistance acquires a paramount importance for the consumer properties. Isotropy in the sense of absolute equalising of the properties between the base and the weft evaluates the achieved optimum cohesion between the weaving threads and directs the weaving cycle settings. The possible variation of the ratio between the elastic modules of the warp and the weft, depending on the weft spacing and the warp tension, is the basic idea of this article.

Weaving meanings from the deliberative process of collegiate management in nursing1

PubMed Central

Higashi, Giovana Dorneles Callegaro; Erdmann, Alacoque Lorenzini

2014-01-01

Objective to understand the meanings of the collegiate deliberations attributed by its members on an undergraduate nursing course. Method Grounded Theory, interviews being held with 30 participants, making up 4 sample groups, between January and June 2012, in a public higher education institution. Result 5 categories emerged, indicating the phenomenon and weaving the paradigmatic model: Understanding the experience of the complex relationships and interactions in the deliberations of collegiate management in nursing: intertwining divergences, convergences, dialogs, collectivities and diversities. This deliberative process presents various meanings involving discussion, and divergent, convergent and complementary positions, through dialog, commitment and negotiation. Conclusion the deliberations in the collegiate of nursing, intertwining dialogs, collectivities and diversities, mold the complex relational fabrics. PMID:26107835

Exotensioned structural members with energy-absorbing effects

DOEpatents

Brockwell, Michael Ian

2014-01-07

Structural members having enhanced load bearing capacity per unit mass include a skeleton structure formed from strips of material. Notches may be placed on the strips and a weave of tensile material placed in the notches and woven around the skeleton structure. At least one pair of structural members can be jointed together to provide very strong joints due to a weave patterns of tensile material, such as Kevlar, that distributes stress throughout the structure, preventing stress from concentrating in one area. Methods of manufacturing such structural members include molding material into skeletons of desired cross section using a matrix of molding segments. Total catastrophic failures in composite materials are substantially avoided and the strength to weight ratio of structures can be increased.

Exotensioned structural members with energy-absorbing effects

DOEpatents

Brockwell, Michael Ian

2017-08-22

Structural members having enhanced load bearing capacity per unit mass include a skeleton structure formed from strips of material. Notches may be placed on the strips and a weave of tensile material placed in the notches and woven around the skeleton structure. At least one pair of structural members can be jointed together to provide very strong joints due to a weave patterns of tensile material, such as Kevlar, that distributes stress throughout the structure, preventing stress from concentrating in one area. Methods of manufacturing such structural members include molding material into skeletons of desired cross section using a matrix of molding segments. Total catastrophic failures in composite materials are substantially avoided and the strength to weight ratio of structures can be increased.

Exotensioned structural members with energy-absorbing effects

DOEpatents

Brockwell, Michael Ian

2015-08-11

Structural members having enhanced load bearing capacity per unit mass include a skeleton structure formed from strips of material. Notches may be placed on the strips and a weave of tensile material placed in the notches and woven around the skeleton structure. At least one pair of structural members can be jointed together to provide very strong joints due to a weave patterns of tensile material, such as Kevlar, that distributes stress throughout the structure, preventing stress from concentrating in one area. Methods of manufacturing such structural members include molding material into skeletons of desired cross section using a matrix of molding segments. Total catastrophic failures in composite materials are substantially avoided and the strength to weight ratio of structures can be increased.

Effects of Structural Flexibility on Motorcycle Straight Running Stability by using Energy Flow Method

NASA Astrophysics Data System (ADS)

Marumo, Yoshitaka; Katayama, Tsuyoshi

This study uses the energy flow method to analyze how structural flexibility affects the motorcycle wobble and weave modes. Lateral bending of the front fork and torsion of the main frame affect the wobble mode stability. These are based on the gyroscopic effect of the front wheel in the steering motion by considering structural flexibility. At high speeds, lateral bending of the front fork and torsion of the rear swing arm more significantly affect the weave mode stability. These are primarily due to the phase changes of the external force generated by the yaw rate in the lateral motion. The phase change of the yaw rate force in the lateral motion originates from the phase change of the tire side forces.

Lightweight engine containment. [Kevlar shielding

NASA Technical Reports Server (NTRS)

Weaver, A. T.

1977-01-01

Kevlar fabric styles and weaves were studied, as well as methods of application for advanced gas turbine engines. The Kevlar material was subjected to high speed impacts by simple projectiles fired from a rifle, as well as more complex shapes such as fan blades released from gas turbine rotors in a spin pit. Just contained data was developed for a variety of weave and/or application techniques, and a comparative containment weight efficiency was established for Kevlar containment applications. The data generated during these tests is being incorporated into an analytical design system so that blade containment trade-off studies between Kevlar and metal case engine structures can be made. Laboratory tests and engine environment tests were performed to determine the survivability of Kevlar in a gas turbine environment.

In-process fault detection for textile fabric production: onloom imaging

NASA Astrophysics Data System (ADS)

Neumann, Florian; Holtermann, Timm; Schneider, Dorian; Kulczycki, Ashley; Gries, Thomas; Aach, Til

2011-05-01

Constant and traceable high fabric quality is of high importance both for technical and for high-quality conventional fabrics. Usually, quality inspection is carried out by trained personal, whose detection rate and maximum period of concentration are limited. Low resolution automated fabric inspection machines using texture analysis were developed. Since 2003, systems for the in-process inspection on weaving machines ("onloom") are commercially available. With these defects can be detected, but not measured quantitative precisely. Most systems are also prone to inevitable machine vibrations. Feedback loops for fault prevention are not established. Technology has evolved since 2003: Camera and computer prices dropped, resolutions were enhanced, recording speeds increased. These are the preconditions for real-time processing of high-resolution images. So far, these new technological achievements are not used in textile fabric production. For efficient use, a measurement system must be integrated into the weaving process; new algorithms for defect detection and measurement must be developed. The goal of the joint project is the development of a modern machine vision system for nondestructive onloom fabric inspection. The system consists of a vibration-resistant machine integration, a high-resolution machine vision system, and new, reliable, and robust algorithms with quality database for defect documentation. The system is meant to detect, measure, and classify at least 80 % of economically relevant defects. Concepts for feedback loops into the weaving process will be pointed out.

Uncommon Teaching in an Unexpected Place

ERIC Educational Resources Information Center

Shore, Rebecca

2014-01-01

Continued physical well-being is important, especially within the aging teacher ranks. The story of one veteran exercise instructor emphasizes fitness and weaves best classroom practices throughout the narrative.

The Carry Loom.

ERIC Educational Resources Information Center

Mihalow, Paula

1980-01-01

Presents instructions for building a simple, inexpensive, one-piece loom that is easy for students and teachers to work with, transport, and store. A short list of books for weaving instruction is appended. (Author/SJL)

College Dorms Ringing an Inner Court.

ERIC Educational Resources Information Center

AIA Journal, 1979

1979-01-01

An AIA Honor Award was given for the Pembroke Dormitories at Brown University. The dormitories, said the jury, are an "outstanding example of weaving an institution into the urban fabric." (Author/MLF)

Adult Learning, Transformative Education, and Indigenous Epistemology

ERIC Educational Resources Information Center

McEachern, Diane

2016-01-01

This chapter describes an innovative program that weaves together adult learning, transformative education, and indigenous epistemology in order to prepare Alaskan rural indigenous social service providers to better serve their communities.

Microstructure of Matrix in UHTC Composites

NASA Technical Reports Server (NTRS)

Johnson, Sylvia; Stackpoole, Margaret; Gusman, Michael I.; Chavez-Garia Jose; Doxtad, Evan

2011-01-01

Approaches to controlling the microstructure of Ultra High Temperature Ceramics (UHTCs) are described.. One matrix material has been infiltrated into carbon weaves to make composite materials. The microstructure of these composites is described.

25 CFR 170.121 - What is a cultural access road?

Code of Federal Regulations, 2014 CFR

2014-04-01

... example: (1) Sacred and medicinal sites; (2) Gathering medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing...

25 CFR 1000.126 - What does “special geographic, historical or cultural” mean?

Code of Federal Regulations, 2011 CFR

2011-04-01

... sites; (2) Gathering of medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing, and gathering. ...

25 CFR 1000.126 - What does “special geographic, historical or cultural” mean?

Code of Federal Regulations, 2012 CFR

2012-04-01

... sites; (2) Gathering of medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing, and gathering. ...

25 CFR 1000.126 - What does “special geographic, historical or cultural” mean?

Code of Federal Regulations, 2014 CFR

2014-04-01

... sites; (2) Gathering of medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing, and gathering. ...

25 CFR 170.121 - What is a cultural access road?

Code of Federal Regulations, 2011 CFR

2011-04-01

... example: (1) Sacred and medicinal sites; (2) Gathering medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing...

25 CFR 170.121 - What is a cultural access road?

Code of Federal Regulations, 2013 CFR

2013-04-01

... example: (1) Sacred and medicinal sites; (2) Gathering medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing...

25 CFR 1000.126 - What does “special geographic, historical or cultural” mean?

Code of Federal Regulations, 2013 CFR

2013-04-01

... sites; (2) Gathering of medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing, and gathering. ...

25 CFR 170.121 - What is a cultural access road?

Code of Federal Regulations, 2012 CFR

2012-04-01

... example: (1) Sacred and medicinal sites; (2) Gathering medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing...

25 CFR 1000.126 - What does “special geographic, historical or cultural” mean?

Code of Federal Regulations, 2010 CFR

2010-04-01

... sites; (2) Gathering of medicines or materials such as grasses for basket weaving; or (3) Other traditional activities, including, but not limited to, subsistence hunting, fishing, and gathering. ...

Weavability of dry polymer powder towpreg

NASA Technical Reports Server (NTRS)

Hugh, Maylene K.; Marchello, Joseph M.; Maiden, Janice R.; Johnston, Norman J.

1993-01-01

Carbon fiber yarns (3k, 6k, 12k) were impregnated with LARC (tm) thermoplastic polyimide dry powder. Parameters for weaving these yarns were established. Eight-harness satin fabrics were successfully woven from each of the three classes of yarns and consolidated into test specimens to determine mechanical properties. It was observed that for optimum results warp yarns should have flexural rigidities between 10,000 and 100,000 mg-cm. Tow handling minimization, low tensioning, and tow bundle twisting were used to reduce fiber breakage, the separation of filaments, and tow-to-tow abrasion. No apparent effect of tow size or twist was observed on either tension or compression modulus. However, fiber damage and processing costs favor the use of 12k yarn bundles versus 3k or 6k yarn bundles in the weaving of powder-coated towpreg.

Performance Technology Program (PTP-S 2). Volume 9: Evaluation of reentry vehicle nosetip transition and heat transfer in the AEDC hyperballistics track G

NASA Astrophysics Data System (ADS)

Wassel, A. T.; Shih, W. C. L.; Curtis, R. J.

1981-01-01

Boundary layer transition and surface heating distributions on graphite fine weave carbon-carbon, and metallic nosetip materials were derived from surface temperature responses measured in nitrogen environments during both free-flight and track-guided testing in the AEDC Hyperballistics Range/Track G. Innovative test procedures were developed, and heat transfer results were validated against established theory through experiments using a super-smooth tungsten model. Quantitative definitions of mean transition front locations were established by deriving heat flux distributions from measured temperatures, and comparisons made with existing nosetip transition correlations. Qualitative transition locations were inferred directly from temperature distributions to investigate preferred orientations on fine weave nosetips. Levels of roughness augmented heat transfer were generally shown to be below values predicted by state of the art methods.

Advanced resin systems and 3D textile preforms for low cost composite structures

NASA Technical Reports Server (NTRS)

Shukla, J. G.; Bayha, T. D.

1993-01-01

Advanced resin systems and 3D textile preforms are being evaluated at Lockheed Aeronautical Systems Company (LASC) under NASA's Advanced Composites Technology (ACT) Program. This work is aimed towards the development of low-cost, damage-tolerant composite fuselage structures. Resin systems for resin transfer molding and powder epoxy towpreg materials are being evaluated for processability, performance and cost. Three developmental epoxy resin systems for resin transfer molding (RTM) and three resin systems for powder towpregging are being investigated. Various 3D textile preform architectures using advanced weaving and braiding processes are also being evaluated. Trials are being conducted with powdered towpreg, in 2D weaving and 3D braiding processes for their textile processability and their potential for fabrication in 'net shape' fuselage structures. The progress in advanced resin screening and textile preform development is reviewed here.

The development of thermoplastic fibre based reinforcements for the rotational moulding process

NASA Astrophysics Data System (ADS)

Alemán, D. N. Castellanos; McCourt, M.; Kearns, M. P.; Martin, P. J.; Butterfield, J.

2018-05-01

Rotational moulding is a method used to produce hollow plastic parts through the heating, melting and cooling of polymer powder within a metal mould. A wide range of products are made using this process, such as fluid containment tanks, boats, light weight vehicle bodies and marine buoys. Rotomoulded composites using thermoplastic fibres are of increasing interest to the industry, as they have the potential to significantly improve impact strength, whilst reducing part weight, resulting in a structure that is 100% recyclable compared to a traditional composite. A series of self-reinforced thermoplastic weaves can be used to produce a number of composite structures using the rotational moulding process. This work outlines the improvements obtained from the range of rotomoulded composites structures, as well as preforms that could be used in future rotational moulding work. Characteristics of self-reinforced materials were exploited with the aim of increasing the mechanical properties, preserving the weaves and increasing the nature of the material adhesion. Addition of the fabrics in the cooling stage was shown to be of great interest as this avoided exposure of the material to the peak temperature, which may affect the integrity of the fabric. Placing the weave during cooling was useful as the material could receive the maximum amount of tensile force during the impact test. A total of nine diverse types of compounds were manufactured and tested, with seven of the impact tests showing an increase in strength greater than 50%.

Computational Homogenization of Mechanical Properties for Laminate Composites Reinforced with Thin Film Made of Carbon Nanotubes

NASA Astrophysics Data System (ADS)

El Moumen, A.; Tarfaoui, M.; Lafdi, K.

2018-06-01

Elastic properties of laminate composites based Carbone Nanotubes (CNTs), used in military applications, were estimated using homogenization techniques and compared to the experimental data. The composite consists of three phases: T300 6k carbon fibers fabric with 5HS (satin) weave, baseline pure Epoxy matrix and CNTs added with 0.5%, 1%, 2% and 4%. Two step homogenization methods based RVE model were employed. The objective of this paper is to determine the elastic properties of structure starting from the knowledge of those of constituents (CNTs, Epoxy and carbon fibers fabric). It is assumed that the composites have a geometric periodicity and the homogenization model can be represented by a representative volume element (RVE). For multi-scale analysis, finite element modeling of unit cell based two step homogenization method is used. The first step gives the properties of thin film made of epoxy and CNTs and the second is used for homogenization of laminate composite. The fabric unit cell is chosen using a set of microscopic observation and then identified by its ability to enclose the characteristic periodic repeat in the fabric weave. The unit cell model of 5-Harness satin weave fabric textile composite is identified for numerical approach and their dimensions are chosen based on some microstructural measurements. Finally, a good comparison was obtained between the predicted elastic properties using numerical homogenization approach and the obtained experimental data with experimental tests.

A tree island approach to inferring phylogeny in the ant subfamily Formicinae, with especial reference to the evolution of weaving.

PubMed

Johnson, Rebecca N; Agapow, Paul-Michael; Crozier, Ross H

2003-11-01

The ant subfamily Formicinae is a large assemblage (2458 species (J. Nat. Hist. 29 (1995) 1037), including species that weave leaf nests together with larval silk and in which the metapleural gland-the ancestrally defining ant character-has been secondarily lost. We used sequences from two mitochondrial genes (cytochrome b and cytochrome oxidase 2) from 18 formicine and 4 outgroup taxa to derive a robust phylogeny, employing a search for tree islands using 10000 randomly constructed trees as starting points and deriving a maximum likelihood consensus tree from the ML tree and those not significantly different from it. Non-parametric bootstrapping showed that the ML consensus tree fit the data significantly better than three scenarios based on morphology, with that of Bolton (Identification Guide to the Ant Genera of the World, Harvard University Press, Cambridge, MA) being the best among these alternative trees. Trait mapping showed that weaving had arisen at least four times and possibly been lost once. A maximum likelihood analysis showed that loss of the metapleural gland is significantly associated with the weaver life-pattern. The graph of the frequencies with which trees were discovered versus their likelihood indicates that trees with high likelihoods have much larger basins of attraction than those with lower likelihoods. While this result indicates that single searches are more likely to find high- than low-likelihood tree islands, it also indicates that searching only for the single best tree may lose important information.

Computational Homogenization of Mechanical Properties for Laminate Composites Reinforced with Thin Film Made of Carbon Nanotubes

NASA Astrophysics Data System (ADS)

El Moumen, A.; Tarfaoui, M.; Lafdi, K.

2017-08-01

Elastic properties of laminate composites based Carbone Nanotubes (CNTs), used in military applications, were estimated using homogenization techniques and compared to the experimental data. The composite consists of three phases: T300 6k carbon fibers fabric with 5HS (satin) weave, baseline pure Epoxy matrix and CNTs added with 0.5%, 1%, 2% and 4%. Two step homogenization methods based RVE model were employed. The objective of this paper is to determine the elastic properties of structure starting from the knowledge of those of constituents (CNTs, Epoxy and carbon fibers fabric). It is assumed that the composites have a geometric periodicity and the homogenization model can be represented by a representative volume element (RVE). For multi-scale analysis, finite element modeling of unit cell based two step homogenization method is used. The first step gives the properties of thin film made of epoxy and CNTs and the second is used for homogenization of laminate composite. The fabric unit cell is chosen using a set of microscopic observation and then identified by its ability to enclose the characteristic periodic repeat in the fabric weave. The unit cell model of 5-Harness satin weave fabric textile composite is identified for numerical approach and their dimensions are chosen based on some microstructural measurements. Finally, a good comparison was obtained between the predicted elastic properties using numerical homogenization approach and the obtained experimental data with experimental tests.

Flexible-pile thermal sealant

NASA Technical Reports Server (NTRS)

Anderson, G. E.; Fell, D. M.; Tesinsky, J. S.

1977-01-01

Brushlike material insulates variable-width gaps where severe thermal stress is present. Weave-and-tuft strip has low thermal conductivity, working temperature range from -454 to 2,000 F, low load compressibility, and good inhibition of plasma flow.

Excursions out-of-lane versus standard deviation of lateral position as outcome measure of the on-the-road driving test.

PubMed

Verster, Joris C; Roth, Thomas

2014-07-01

The traditional outcome measure of the Dutch on-the-road driving test is the standard deviation of lateral position (SDLP), the weaving of the car. This paper explores whether excursions out-of-lane are a suitable additional outcome measure to index driving impairment. A literature search was conducted to search for driving tests that used both SDLP and excursions out-of-lane as outcome measures. The analyses were limited to studies examining hypnotic drugs because several of these drugs have been shown to produce next-morning sedation. Standard deviation of lateral position was more sensitive in demonstrating driving impairment. In fact, solely relying on excursions out-of-lane as outcome measure incorrectly classifies approximately half of impaired drives as unimpaired. The frequency of excursions out-of-lane is determined by the mean lateral position within the right traffic lane. Defining driving impairment as having a ΔSDLP > 2.4 cm, half of the impaired driving tests (51.2%, 43/84) failed to produce excursions out-of-lane. Alternatively, 20.9% of driving tests with ΔSDLP < 2.4 cm (27/129) had at least one excursion out-of-lane. Excursions out-of-lane are neither a suitable measure to demonstrate driving impairment nor is this measure sufficiently sensitive to differentiate adequately between differences in magnitude of driving impairment. Copyright © 2014 John Wiley & Sons, Ltd.

Split off-specular reflection and surface scattering from woven materials

NASA Astrophysics Data System (ADS)

Pont, Sylvia C.; Koenderink, Jan J.

2003-03-01

We measured radiance distributions for black lining cloth and copper gauze using the convenient technique of wrapping the materials around a circular cylinder, irradiating it with a parallel light source and collecting the scattered radiance by a digital camera. One family of parallel threads (weave or weft) was parallel to the cylinder generator. The most salient features for such glossy plane weaves are a splitting up of the reflection peak due to the wavy variations in local slopes of the threads around the cylinders and a surface scattering lobe due to the threads that run along the cylinder. These scattering characteristics are quite different from the (off-)specular peaks and lobes that were found before for random rough specular surfaces. The split off-specular reflection is due to the regular structures in our samples of man-made materials. We derived simple approximations for these reflectance characteristics using geometrical optics.

The effect of fibre orientation on a TWCP composite

NASA Astrophysics Data System (ADS)

Barnes, Nicholas; Wood, David; Appleby-Thomas, Gareth; Leighs, James; Roberts, Andrew; Hazell, Paul

2013-06-01

Multiple authors have shown that orientation can greatly affect the shock profiles seen in composites. Carbon fibre composites are employed in multiple sectors, with their use in the aerospace industry becoming more prevalent. An angle of 20° between the outer surface and the weave direction provides a good compromise between strength and ablation. Using a single stage gas gun with manganin pressure gauges the shock response of both a 90° and 45° layup TWCP composite were investigated up to a particle velocity of c.a. 1 mm μs-1, in both the US-up and pressure-volume plane. Comparisons in terms of shock propagation were also made with previously investigated TWCP orientations of 0° and 20° as well as other carbon fibre based composites from the literature. This allowed a detailed interrogation of the effects of weave orientation in this important TWCP composite to be made.

The Layer of Kevlar Angle-interlock Woven Fabric Effect on the Tensile Properties of Composite Materials

NASA Astrophysics Data System (ADS)

Xie, Wan-Chen; Guo, Xu-Yi; Yan, Tao; Zhang, Shang-Yong

2017-09-01

This article is based on the structure of three-dimensional angle-interlock longitudinal.The 3-layer, 5-layer, 7-layer and 9-layer of angle-interlock 3D fabrics are woven on sample weaving machine respectively with the 1500D Kevlar fiber twist filament produced by United States DuPont. At the same time, Kevlar plain weave fabric is woven, and three, five, seven and nine layers’ fabric are to be compared. In the process of VARTM composite technology, epoxy resin is matrix material, acetone is diluent, triethylene tetramine is curing agent and the five different fabrics are the reinforced materials respectively. Finally, eight different three-dimensional woven fabric composites were prepared. In this paper, the tensile properties of eight kinds of three-dimensional woven fabric composites were tested respectively.Finally, it is concluded that the five-layer angle-interlock woven fabric prepared by Kevlar fiber shows the best tensile property.

Environmental change and economic development in coastal Peru between 5,800 and 3,600 years ago

PubMed Central

Sandweiss, Daniel H.; Solís, Ruth Shady; Moseley, Michael E.; Keefer, David K.; Ortloff, Charles R.

2009-01-01

Between ≈5,800 and 3,600 cal B.P. the biggest architectural monuments and largest settlements in the Western Hemisphere flourished in the Supe Valley and adjacent desert drainages of the arid Peruvian coast. Intensive net fishing, irrigated orchards, and fields of cotton with scant comestibles successfully sustained centuries of increasingly complex societies that did not use ceramics or loom-based weaving. This unique socioeconomic adaptation was abruptly abandoned and gradually replaced by societies more reliant on food crops, pottery, and weaving. Here, we review evidence and arguments for a severe cycle of natural disasters—earthquakes, El Niño flooding, beach ridge formation, and sand dune incursion—at ≈3,800 B.P. and hypothesize that ensuing physical changes to marine and terrestrial environments contributed to the demise of early Supe settlements. PMID:19164564

Powder-Coated Towpreg: Avenues to Near Net Shape Fabrication of High Performance Composites

NASA Technical Reports Server (NTRS)

Johnston, N. J.; Cano, R. J.; Marchello, J. M.; Sandusky, D. A.

1995-01-01

Near net shape parts were fabricated from powder-coated preforms. Key issues including powder loss during weaving and tow/tow friction during braiding were addressed, respectively, by fusing the powder to the fiber prior to weaving and applying a water-based gel to the towpreg prior to braiding. A 4:1 debulking of a complex 3-D woven powder-coated preform was achieved in a single step utilizing expansion rubber molding. Also, a process was developed for using powder-coated towpreg to fabricate consolidated ribbon having good dimensional integrity and low voids. Such ribbon will be required for in situ fabrication of structural components via heated head advanced tow placement. To implement process control and ensure high quality ribbon, the ribbonizer heat transfer and pulling force were modeled from fundamental principles. Most of the new ribbons were fabricated from dry polyarylene ether and polymide powders.

The Electrical and Thermal Conductivity of Woven Pristine and Intercalated Graphite Fiber-Polymer Composites

NASA Technical Reports Server (NTRS)

Gaier, James R.; Vandenburg, Yvonne Yoder; Berkebile, Steven; Stueben, Heather; Balagadde, Frederick

2002-01-01

A series of woven fabric laminar composite plates and narrow strips were fabricated from a variety of pitch-based pristine and bromine intercalated graphite fibers in an attempt to determine the influence of the weave on the electrical and thermal conduction. It was found generally that these materials can be treated as if they are homogeneous plates. The rule of mixtures describes the resistivity of the composite fairly well if it is realized that only the component of the fibers normal to the equipotential surface will conduct current. When the composite is narrow with respect to the fiber weave, however, there is a marked angular dependence of the resistance which was well modeled by assuming that the current follows only along the fibers (and not across them in a transverse direction), and that the contact resistance among the fibers in the composite is negligible. The thermal conductivity of composites made from less conductive fibers more closely followed the rule of mixtures than that of the high conductivity fibers, though this is thought to be an artifact of the measurement technique. Electrical and thermal anisotropy could be induced in a particular region of the structure by weaving together high and low conductivity fibers in different directions, though this must be done throughout all of the layers of the structure as interlaminar conduction precludes having only the top layer carry the anisotropy. The anisotropy in the thermal conductivity is considerably less than either that predicted by the rule of mixtures or the electrical resistivity.

Influence of fibre reinforcement on selected mechanical properties of dental composites.

PubMed

Niewczas, Agata M; Zamościńska, Jolanta; Krzyżak, Aneta; Pieniak, Daniel; Walczak, Agata; Bartnik, Grzegorz

2017-01-01

For splinting or designing adhesive bridges, reconstructive composite structures with increased mechanical properties owing to embedded reinforcement fibres are used. The aim of this article was to determine the influence of glass and aramid fibres on the mechanical strength of composites reinforced with these fibres. Two polymer-ceramic microhybrid materials: Boston and Herculite were tested. Three types of reinforcement fibres were used: aramid (Podwiązka) with a single layer weave, a single layer weave glass fibre (FSO) and triple layer weave glass fibre (FSO evo). Tests were conducted in accordance with the requirements of ISO 4049:2009. The following material types were chosen for research: Boston, Boston + Podwiązka, Herculite, Herculite + Podwiązka, Herculite + FSO and Herculite + FSO evo. The scope of research included: flexural strength B, bending modulus of elasticity εB and work to failure of the reinforced composite Wfb. Additionally, microscopic observations of fracture occurring in samples were made. In comparison: the Herculite (97.7 MPa) type with the Herculite + FSO evo (177.5 MPa) type was characterized by the highest strength. Fibre reinforcement resulted in decreasing the elasticity modulus: Herculite + reinforcement (6.86 GPa; 6.33 GPa; 6.11 GPa) in comparison with the Herculite (9.84 GPa) and respectively Boston + reinforcement (10.08 GPa) as compared with the Boston (11.81 GPa). Using glass fibres increases flexural strength of the test composites. Using aramid fibres does not change their strength. The elasticity modulus of the reinforced reconstructive structures decreases after application of either type of fibres. However, their resistance to the crack initiation increases.

Shoulder girdle muscle activity and fatigue in traditional and improved design carpet weaving workstations.

PubMed

Allahyari, Teimour; Mortazavi, Narges; Khalkhali, Hamid Reza; Sanjari, Mohammad Ali

2016-01-01

Work-related musculoskeletal disorders in the neck and shoulder regions are common among carpet weavers. Working for prolonged hours in a static and awkward posture could result in an increased muscle activity and may lead to musculoskeletal disorders. Ergonomic workstation improvements can reduce muscle fatigue and the risk of musculoskeletal disorders. The aim of this study is to assess and to compare upper trapezius and middle deltoid muscle activity in 2 traditional and improved design carpet weaving workstations. These 2 workstations were simulated in a laboratory and 12 women carpet weavers worked for 3 h. Electromyography (EMG) signals were recorded during work in bilateral upper trapezius and bilateral middle deltoid. The root mean square (RMS) and median frequency (MF) values were calculated and used to assess muscle load and fatigue. Repeated measure ANOVA was performed to assess the effect of independent variables on muscular activity and fatigue. The participants were asked to report shoulder region fatigue on the Borg's Category-Ratio scale (Borg CR-10). Root mean square values in workstation A are significantly higher than in workstation B. Furthermore, EMG amplitude was higher in bilateral trapezius than in bilateral deltoid. However, muscle fatigue was not observed in any of the workstations. The results of the study revealed that muscle load in a traditional workstation was high, but fatigue was not observed. Further studies investigating other muscles involved in carpet weaving tasks are recommended. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Understanding personal narratives: an approach to practice.

PubMed

Sander, Ruth

2005-04-01

Nurses can collaborate with people to express their stories or life journey portraits through arts such as dance, painting, photography, weaving or story-telling, and to cast themselves as heroes in their own stories rather than victims of life's circumstances.

Weaving Silos--A Leadership Challenge: A Cross-Functional Team Approach to Supporting Web-Based Student Services

ERIC Educational Resources Information Center

Kleemann, Gary L.

2005-01-01

The author reviews the evolution of Web services--from information sharing to transactional to relationship building--and the progression from first-generation to fourth-generation Web sites. (Contains 3 figures.)

Weaving Traditional Ecological Knowledge into Biological Education: A Call to Action.

ERIC Educational Resources Information Center

Kimmerer, Robin Wall

2002-01-01

Traditional ecological knowledge has value not only for the wealth of biological information it contains but also for the cultural framework of respect, reciprocity, and responsibility in which it is embedded. (Contains 48 references.) (DDR)

Confronting Discrimination and the Integrative Curriculum.

ERIC Educational Resources Information Center

Manning-Miller, Carmen

1993-01-01

Argues for the importance of weaving disability issues into all the courses in a journalism curriculum. Discusses ways to do so in classes on the news editorial, on public relations and advertising, and on mass media history, policy, and ethics. (SR)

25 CFR 309.13 - What are examples of other weaving and textiles that are Indian products?

Code of Federal Regulations, 2012 CFR

2012-04-01

..., including, but not limited to, cornhusk, raffia, tule, horsehair, cotton, wool, fiber, linen, rabbit skin..., star quilts, pictorial appliqué wall hangings, fiber woven bags, embroidered dance shawls, rabbit skin...

25 CFR 309.13 - What are examples of other weaving and textiles that are Indian products?

Code of Federal Regulations, 2013 CFR

2013-04-01

..., including, but not limited to, cornhusk, raffia, tule, horsehair, cotton, wool, fiber, linen, rabbit skin..., star quilts, pictorial appliqué wall hangings, fiber woven bags, embroidered dance shawls, rabbit skin...

25 CFR 309.13 - What are examples of other weaving and textiles that are Indian products?

Code of Federal Regulations, 2014 CFR

2014-04-01

..., including, but not limited to, cornhusk, raffia, tule, horsehair, cotton, wool, fiber, linen, rabbit skin..., star quilts, pictorial appliqué wall hangings, fiber woven bags, embroidered dance shawls, rabbit skin...

23 CFR 771.117 - Categorical exclusions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... management systems, electronic payment equipment, automatic vehicle locaters, automated passenger counters..., reconstruction, adding shoulders, or adding auxiliary lanes (e.g., parking, weaving, turning, climbing). (2... fringe parking facilities. (5) Construction of new truck weigh stations or rest areas. (6) Approvals for...

40 CFR 410.32 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Low Water Use Processing... 9.0 at all times. Water Jet Weaving Pollutant or pollutant property BPT limitations Maximum for any...

Silk produced by hornets: thermophotovoltaic properties-a review.

PubMed

Kirshboim, S; Ishay, J S

2000-09-01

This article deals with the silk weave produced by pupating larvae of the Oriental hornet and its electric properties. Larvae of this hornet commence pupation at approximately 2 weeks of age. Creation of the cocoonal silk weave requires a number of hours and the encased pupa remains in the cocoon for approximately 2 more weeks before ecloding as an adult. The silk weave is initially of a creamish white color, but gradually becomes brown-gray owing to the activity of certain bacteria secreted in the silk. The silk weave is composed of fibers arranged in multiple layers with interposed surfaces occupying a considerable part of the area and containing pockets of bacteria. The spun silk contains both metallic and non-metallic elements, mostly K and Cl but also Mg, P, S, Ca, Ti and V. Shaped as a dome, the silk projects considerably beyond the cell proper, contributing importantly to its total volume and providing a shield for the contained pupa against predators, parasites, or extreme changes in temperature, as well as affording a 'sterile and clean room' in which the pupa can form its new cuticle without the interference of contaminating dust particles or the turbulence of air currents. The silk is endowed with electric properties. Inter alia, a thermoelectric phenomenon was observed in the dark, namely, upon increase in temperature the current rose to several hundred nano Amperes (nA); in light, a photovoltaic effect was observed involving voltages of several dozen millivolts (mV), with a sharp transition between the current and voltage during transition from darkness to light. Also recorded was a very high electric capacitance, amounting to scores of milli farads (mF). In all, the pupal silk behaves like an organic semiconductor, in that its electric properties are temperature-dependent, and it also displays ferroelectric properties. Additionally, a luminescence phenomenon was recorded on the silk, wherein excitation at wavelengths within the UV(i.e. 249, 290 and 312 nm) range yielded an emission spectrum at a wavelength of 450 and of 530 nm. The silk caps are anisotropic in that the emission from the outside is lower than that from the inside. By way of recap, the various mentioned properties of the pupal silk are discussed from their biological and physical aspects.

Chaos Theory: Self-Organization and Symbolic Representation in Family Systems.

ERIC Educational Resources Information Center

Butz, Michael R.; Carlson, J. Matthew; Carlson, Jon

1998-01-01

Proposes an integration of the use of symbols and metaphors that illustrates nonlinear dynamics through a case example weaving together contemporary science and human development in the context of family therapy. Discusses areas of future study. (Author/MKA)

The Experiences and Insights of One Community College Foster Alum and One Community College Faculty Advocate

ERIC Educational Resources Information Center

Westland, Melinda A.; Totten, Volena

2018-01-01

Using personal narratives, in this chapter the authors weave together two distinct perspectives to illuminate the stark reality of many students' experiences as they transition from the foster care system to postsecondary education.

In Practice: Weaving the Campus Safety Net by Integrating Student Health Issues into the Curriculum

ERIC Educational Resources Information Center

Olson, Todd A.; Riley, Joan B.

2009-01-01

Georgetown University has developed an innovative approach to addressing student health and wellness issues through curriculum infusion--a collaborative pedagogy that introduces real-life health issues faced by college students into their academic courses.

Latin American Folk Art Prints

ERIC Educational Resources Information Center

Navah, Jan

2011-01-01

Latin American customs and colors play an important role as second graders are introduced to multicultural experiences through food, music, dance, art, and craft. In this article, the author describes a printing project inspired by Guatemalan weavings and amate bark paintings. (Contains 2 online resources.)

Public roads : a journal of highway research. Vol. 25, No. 10

DOT National Transportation Integrated Search

1949-10-01

In this issue of Public Roads appears the first portion of an important work on highway capacity and its practical applications. The second half of the report, dealing with intersections at grade, weaving sections and unsignalized cross movements, ra...

Power Teaching

ERIC Educational Resources Information Center

Fluellen, Jerry E., Jr.

2007-01-01

Power Teaching weaves four factors into a seamless whole: standards, teaching thinking, research based strategies, and critical inquiry. As a prototype in its first year of development with an urban fifth grade class, the power teaching model connects selected district standards, thinking routines from Harvard University Project Zero Research…

Preparing Students for the 21st Century through the Study of World Music

ERIC Educational Resources Information Center

Beegle, Amy Christine

2014-01-01

This column provides examples of activities that general music teachers might use to weave global awareness into web-based lessons to promote the development of information literacy, media literacy, and communication literacy through the study of world music.

Braid read-only memory

NASA Technical Reports Server (NTRS)

Mckenna, J. F.

1973-01-01

Transformer-type memory is fault-tolerant array of independent read-only memory units. Information pattern in each unit is written by weaving wires through array of linear (nonswitching) transformers. Presence or absence of a bit is determined by whether a given wire threads or bypasses given transformer.

Be the Change You Wish to See: An Interview with Arun Gandhi.

ERIC Educational Resources Information Center

B'Hahn, Carmella

2001-01-01

Arun Gandhi was taught well by his legendary grandfather, Mohandas K. Ghandi. In this interview, he weaves his wisdom about facing adversity, anger, and prejudice with his personal stories of life's challenges, including the assassination of his grandfather. (BF)

Improving Writing: Resources, Strategies, Assessments.

ERIC Educational Resources Information Center

Lenski, Susan Davis; Johns, Jerry L.

Comprehensive and practical, this book provides resources, strategies, and assessments that seamlessly weave writing into everyday classroom routines. The resources in the book include reproducible student worksheets, transparency masters, teacher and student examples, and technology tips in the form of Web site addresses. Strategies throughout…

Weaves as an Interconnection Fabric for ASIM's and Nanosatellites

NASA Technical Reports Server (NTRS)

Gorlick, Michael M.

1995-01-01

Many of the micromachines under consideration require computer support, indeed, one of the appeals of this technology is the ability to intermix mechanical, optical, analog, and digital devices on the same substrate. The amount of computer power is rarely an issue, the sticking point is the complexity of the software required to make effective use of these devices. Micromachines are the nano-technologist's equivalent of 'golden screws'. In other words, they will be piece parts in larger assemblages. For example, a nano-satellite may be composed of stacked silicon wafers where each wafer contains hundreds to thousands of micromachines, digital controllers, general purpose computers, memories, and high-speed bus interconnects. Comparatively few of these devices will be custom designed, most will be stock parts selected from libraries and catalogs. The novelty will lie in the interconnections. For example, a digital accelerometer may be a component part in an adaptive suspension, a monitoring element embedded in the wrapper of a package, or a portion of the smart skin of a launch vehicle. In each case, this device must inter-operate with other devices and probes for the purposes of command, control, and communication. We propose a software technology called 'weaves' that will permit large collections of micromachines and their attendant computers to freely intercommunicate while preserving modularity, transparency, and flexibility. Weaves are composed of networks of communicating software components. The network, and the components comprising it, may be changed even while the software, and the devices it controls, are executing. This unusual degree of software plasticity permits micromachines to dynamically adapt the software to changing conditions and allows system engineers to rapidly and inexpensively develop special purpose software by assembling stock software components in custom configurations.

Micromechanics of fatigue in woven and stitched composites

NASA Technical Reports Server (NTRS)

Cox, B. N.; Carter, W. C.; Dadkhah, M. S.; Morris, W. L.

1994-01-01

The goals of this research program were to: (1) determine how microstructural factors, especially the architecture of reinforcing fibers, control stiffness, strength, and fatigue life in 3D woven composites; (2) identify mechanisms of failure; (3) model composite stiffness; (4) model notched and unnotched strength; and (5) model fatigue life. We have examined a total of eleven different angle and orthogonal interlock woven composites. Extensive testing has revealed that these 3D woven composites possess an extraordinary combination of strength, damage tolerance, and notch insensitivity in compression and tension and in monotonic and cyclic loading. In many important regards, 3D woven composites far outstrip conventional 2D laminates or stitched laminates. Detailed microscopic analysis of damage has led to a comprehensive picture of the essential mechanisms of failure and how they are related to the reinforcement geometry. The critical characteristics of the weave architecture that promote favorable properties have been identified. Key parameters are tow size and the distributions in space and strength of geometrical flaws. The geometrical flaws should be regarded as controllable characteristics of the weave in design and manufacture. In addressing our goals, the simplest possible models of properties were always sought, in a blend of old and new modeling concepts. Nevertheless, certain properties, especially regarding damage tolerance, ultimate failure, and the detailed effects of weave architecture, require computationally intensive stochastic modeling. We have developed a new model, the 'binary model,' to carry out such tasks in the most efficient manner and with faithful representation of crucial mechanisms. This is the final report for contract NAS1-18840. It covers all work from April 1989 up to the conclusion of the program in January 1993.

Weaving a Formal Methods Education with Problem-Based Learning

NASA Astrophysics Data System (ADS)

Gibson, J. Paul

The idea of weaving formal methods through computing (or software engineering) degrees is not a new one. However, there has been little success in developing and implementing such a curriculum. Formal methods continue to be taught as stand-alone modules and students, in general, fail to see how fundamental these methods are to the engineering of software. A major problem is one of motivation — how can the students be expected to enthusiastically embrace a challenging subject when the learning benefits, beyond passing an exam and achieving curriculum credits, are not clear? Problem-based learning has gradually moved from being an innovative pedagogique technique, commonly used to better-motivate students, to being widely adopted in the teaching of many different disciplines, including computer science and software engineering. Our experience shows that a good problem can be re-used throughout a student's academic life. In fact, the best computing problems can be used with children (young and old), undergraduates and postgraduates. In this paper we present a process for weaving formal methods through a University curriculum that is founded on the application of problem-based learning and a library of good software engineering problems, where students learn about formal methods without sitting a traditional formal methods module. The process of constructing good problems and integrating them into the curriculum is shown to be analagous to the process of engineering software. This approach is not intended to replace more traditional formal methods modules: it will better prepare students for such specialised modules and ensure that all students have an understanding and appreciation for formal methods even if they do not go on to specialise in them.

A Novel Junctional Tether Weave Technique for Adult Spinal Deformity: 2-Dimensional Operative Video.

PubMed

Buell, Thomas J; Mullin, Jeffrey P; Nguyen, James H; Taylor, Davis G; Garces, Juanita; Mazur, Marcus D; Buchholz, Avery L; Shaffrey, Mark E; Yen, Chun-Po; Shaffrey, Christopher I; Smith, Justin S

2018-06-05

Proximal junctional kyphosis (PJK) is a common problem after multilevel spine instrumentation for adult spinal deformity. Various anti-PJK techniques such as junctional tethers for ligamentous augmentation have been proposed. We present an operative video demonstrating technical nuances of junctional tether "weave" application. A 70-yr-old male with prior L2-S1 instrumented fusion presented with worsening back pain and posture. Imaging demonstrated pathological loss of lumbar lordosis (flat back deformity), proximal junctional failure, and pseudarthrosis. The patient had severe global and segmental sagittal malalignment, with sagittal vertical axis (SVA, C7-plumbline) measuring 22.3 cm, pelvic incidence (PI) 55°, lumbar lordosis (LL) 8° in kyphosis, pelvic tilt (PT) 30°, and thoracic kyphosis (TK) 6°. The patient gave informed consent for surgery and use of imaging for medical publication. Briefly, surgery first involved re-instrumentation with bilateral pedicle screws from T10 to S1. After right-sided iliac screw fixation (left-sided iliac screw fixation was not performed due to extensive prior iliac crest bone graft harvesting), we then completed a L2-3 Smith-Petersen osteotomy, extended L4 pedicle subtraction osteotomy, and L3-4 interbody arthrodesis with a 12° lordotic cage (9 × 14 × 40 mm). Cobalt Chromium rods were placed spanning the instrumentation bilaterally, and accessory supplemental rods spanning the PSO were attached. An anti-PJK junctional tether "weave" was then implemented using 4.5 mm polyethylene tape (Mersilene tape [Ethicon, Somerville, New Jersey]). Postoperative imaging demonstrated improved alignment (SVA 2.8 cm, PI 55°, LL 53°, PT 25°, TK 45°) and no significant neurological complications occurred during convalescence or at 6 mo postop.

Beyond Basket Weaving: Multicultural Education and Whole-School Reform.

ERIC Educational Resources Information Center

May, Stephen A.

This paper outlines the various limitations of several multicultural education initiatives and explores the conditions necessary for making multicultural education actually work. The conditions examined include the centrality of first language maintenance and the reconstituting of curriculum, pedagogy, evaluation, and organization at the school…

Establishing a Framework for Quality

ERIC Educational Resources Information Center

Lehman, Kirby

2006-01-01

The Jenks School District applies a continuous improvement approach that focuses on academics, arts, activities, athletics and attitude, weaving in leadership, professional development, technology and data-based decision making to prepare all learners to be productive, responsible citizens. Since 1998, the Jenks School District has embraced a…

Teaching as Jazz

ERIC Educational Resources Information Center

Tomlinson, Carol Ann; Germundson, Amy

2007-01-01

Tomlinson and Germundson compare teaching well to playing jazz well. Excellent teaching involves a blend of techniques and theory; expressiveness; syncopation; call and response, and, frequently, improvisation. Weaving in analogies to jazz, the authors delineate four elements of such teaching: curriculum that helps students connect to big ideas,…

Flipping the HSI Narrative: An HSI Positionality

ERIC Educational Resources Information Center

Núñez, Anne-Marie

2017-01-01

Historically, the predominant narrative framing Hispanic-Serving Institutions (HSIs) is that they are monolithic and underperforming, inscribed in a false dichotomy as "Hispanic-Serving" or merely "Hispanic-Enrolling" (Núñez, Hurtado, & Calderón Galdeano, 2015). Together, these narrative threads weave a deficit perspective…

"The World in a Drop of Water": The Feminist Vision of Patricia Howell.

ERIC Educational Resources Information Center

Holmlund, Chris

1993-01-01

Discusses two films ("Dos veces mujer" and "Intima raiz") of Patricia Howell. Demonstrates how thoroughly the feminist themes Howell's films weave together around motherhood are inflected by the specific Latin American and Costa Rican contexts in which she works. (RS)

Intergenerational Programs: Weaving Hearts and Minds.

ERIC Educational Resources Information Center

Duggar, Margaret Lynn; And Others

This publication spotlights the success and diversity of Florida's many intergenerational programs. It describes what intergenerational programming is and the three community needs that intergenerational programs address. Statistics on older persons as well as youth and families in Florida are followed by a listing of what intergenerational…

75 FR 65609 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-26

.../50 x 2/50 Thread Count (warp): 32 to 33 cm Thread Count (weft): 25.5 to 26.5 picks/cm Weave Type...: Piece dyed, then over dyed (single uniform color) Finishing Processes: (CRF) Finish softeners, singed...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

19 CFR 10.212 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... in” means that all of the components of the textile or apparel article (including thread, decorative...,” when used with reference to fabric(s), means that all of the production processes, starting with... with a fabric by a weaving, knitting, needling, tufting, felting, entangling or other process, took...

Helping Them Grow.

ERIC Educational Resources Information Center

Brodkin, Adele M.; And Others

1995-01-01

Three articles discuss how to help elementary students grow. The first explains how teachers can weave a broader safety net for children with chaotic lives. The second presents year-end cooperative games for testing students' communication skills. The third offers take-home summer activities for parents and children. (SM)

Patchwork Plagiarism

ERIC Educational Resources Information Center

Cooper, Janice

2007-01-01

In this Information Age, students produce research projects by piecing together passages quoted verbatim and stitched together with a few introductory or transitional words. They assemble research as patchwork quilts rather than weaving a fabric of new knowledge. This common practice raises ethical issues and poses new challenges for library media…

Weaving Social Foundations through Dance Pedagogy: A Pedagogy of Uncovering

ERIC Educational Resources Information Center

Barr, Sherrie; Risner, Doug

2014-01-01

Today's dance educators enter classrooms populated by increasingly diverse students in which teachers' pedagogical knowledge necessitates heightened understandings of race, ethnicity, social class, gender, and sexuality. Uncovering taken-for-granted assumptions, dominant stereotypes, and educational structures that reproduce social…

Operant Variability: Procedures and Processes

ERIC Educational Resources Information Center

Machado, Armando; Tonneau, Francois

2012-01-01

Barba's (2012) article deftly weaves three main themes in one argument about operant variability. From general theoretical considerations on operant behavior (Catania, 1973), Barba derives methodological guidelines about response differentiation and applies them to the study of operant variability. In the process, he uncovers unnoticed features of…

Rationalizing Cooperation: Moroccan Craft, Politics, and Education

ERIC Educational Resources Information Center

Nicholas, Claire

2018-01-01

State attempts to rationalize Moroccan craft education reflect the ambivalent status of traditional knowledge in a modern economy. Female artisans, recently organized as a cooperative, navigate this ambivalence in a weaving "theory" class and in their "occupation" of the cooperative structure itself. During performances of…

Student Leadership: Challenges and Possibilities

ERIC Educational Resources Information Center

Nel, Willy

2016-01-01

In my attempt to adhere to the request that I provide an interpretation of the theme for the session, "Critical Engagement, Innovation and Inclusivity", and cognisant of the primary audience, I weave student leadership responsibilities, challenges and possibilities into the address. Events since the plenary address have however…

Modeling Woven Polymer Matrix Composites with MAC/GMC

NASA Technical Reports Server (NTRS)

Bednarcyk, Brett A.; Arnold, Steven M. (Technical Monitor)

2000-01-01

NASA's Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) is used to predict the elastic properties of plain weave polymer matrix composites (PMCs). The traditional one step three-dimensional homogertization procedure that has been used in conjunction with MAC/GMC for modeling woven composites in the past is inaccurate due to the lack of shear coupling inherent to the model. However, by performing a two step homogenization procedure in which the woven composite repeating unit cell is homogenized independently in the through-thickness direction prior to homogenization in the plane of the weave, MAC/GMC can now accurately model woven PMCs. This two step procedure is outlined and implemented, and predictions are compared with results from the traditional one step approach and other models and experiments from the literature. Full coupling of this two step technique with MAC/ GMC will result in a widely applicable, efficient, and accurate tool for the design and analysis of woven composite materials and structures.

Manufacturing process for the WEAVE prime focus corrector optics for the 4.2m William Hershel Telescope

NASA Astrophysics Data System (ADS)

Lhomé, Emilie; Agócs, Tibor; Abrams, Don Carlos; Dee, Kevin M.; Middleton, Kevin F.; Tosh, Ian A.; Jaskó, Attila; Connor, Peter; Cochrane, Dave; Gers, Luke; Jonas, Graeme; Rakich, Andrew; Benn, Chris R.; Balcells, Marc; Trager, Scott C.; Dalton, Gavin B.; Carrasco, Esperanza; Vallenari, Antonella; Bonifacio, Piercarlo; Aguerri, J. Alfonso L.

2016-07-01

In this paper, we detail the manufacturing process for the lenses that will constitute the new two-degree field-of-view Prime Focus Corrector (PFC) for the 4.2m William Herschel Telescope (WHT) optimised for the upcoming WEAVE Multi-Object Spectroscopy (MOS) facility. The corrector, including an Atmospheric Dispersion Corrector (ADC), is made of six large lenses, the largest being 1.1-meter diameter. We describe how the prescriptions of the optical design were translated into manufacturing specifications for the blanks and lenses. We explain how the as-built glass blank parameters were fed back into the optical design and how the specifications for the lenses were subsequently modified. We review the critical issues for the challenging manufacturing process and discuss the trade-offs that were necessary to deliver the lenses while maintaining the optimal optical performance. A short description of the lens optical testing is also presented. Finally, the subsequent manufacturing steps, including assembly, integration, and alignment are outlined.

The effect of weave orientation on the BRDF of tarp samples

NASA Astrophysics Data System (ADS)

Georgiev, Georgi; Butler, James J.

2003-10-01

The results of bi-directional reflectance distribution function (BRDF) measurements of four tarp samples obtained from NASA"s Stennis Space Center (SSC) are presented. The measurements were performed in the Diffuser Calibration Facility (DCaF) at NASA"s Goddard Space Flight Center (GSFC). The samples are of similar material structure but different reflectance. The experimental data were obtained with a Xe arc lamp/monochromator light source as well as laser light sources in the ultraviolet, visible, and near infrared spectral regions. The BRDF data were recorded at four incident zenith angles and at five incident azimuth angles. The dependence of the measured BRDF on weave orientation was analyzed and presented. 8 degree irectional/hemispherical reflectance data were also measured for each tarp sample, and those results are also reported. All results are NIST traceable through calibrated standard plates. The specular and diffuse scatter data obtained from these studies are used by NASA"s SSC in their field-based, vicarious calibration of satellite and airborne remote sensing instruments.

The influence of varied gravito-inertial fields on the cardiac response of orb-weaving spiders

NASA Technical Reports Server (NTRS)

Finck, A.

1982-01-01

The Gz transfer function was described for the orb weaving spider A. sericatus. The functional relationship between the heartrate and the intensity of G is linear in the form of: Y = a Log Gz-1 +k. The heartrate in unrestrained animals was recorded by a laser plethysmograph developed specifically for this purpose. Following a control, sample heartrate were taken postrotation between 1.001 and 1.5 Gz in 6 steps. The underlying distribution of heartrates does not appear significantly different from a Gaussian distribution. A method of varnishing the legs of the spider was developed. This was done in order to compromise the lyriform organs, especially those located on the patellae. The lyriform organ is hypothesized to serve the receptor role in the transduction of gravity related stimuli. In preliminary animals the Gz function, post varnishing of the patellae, appears to be changed in the direction of poorer discrimination. We also observed that the resting heartrate following the varnish procedure is substantially increased.

Analysis of woven and braided fabric reinforced composites

NASA Technical Reports Server (NTRS)

Naik, Rajiv A.

1994-01-01

A general purpose micromechanics analysis that discretely models the yarn architecture within the textile repeating unit cell, was developed to predict overall, three dimensional, thermal and mechanical properties. This analytical technique was implemented in a user-friendly, personal computer-based, windows compatible code called Textile Composite Analysis for Design (TEXCAD). TEXCAD was used to analyze plain, 5-harness satin, and 8-harness satin weave composites along with 2-D braided and 2x2, 2-D triaxial braided composites. The calculated overall stiffnesses correlated well with available 3-D finite element results and test data for both the woven and the braided composites. Parametric studies were performed to investigate the effects of yarn size on the yarn crimp and the overall thermal and mechanical constants for plain weave composites. The effects of braid angle were investigated for the 2-D braided composites. Finally, the effects of fiber volume fraction on the yarn undulations and the thermal and mechanical properties of 2x2, 2-D triaxial braided composites were also investigated.

Musculoskeletal symptoms as related to ergonomic factors in Iranian hand-woven carpet industry and general guidelines for workstation design.

PubMed

Choobineh, Alireza; Lahmi, Mohammadali; Shahnavaz, Houshang; Jazani, Reza Khani; Hosseini, Mostafa

2004-01-01

Carpet weaving is a high risk occupation for developing musculoskeletal disorders (MSDs). The objectives of the present study, which was carried out in the Iranian hand-woven carpet industry, were determination of the prevalence of MSD symptoms, identification of major factors associated with MSD symptoms and development of guidelines for workstation design. 1,439 randomly selected weavers participated in this study. A questionnaire was used to collect data on MSD symptoms. The results revealed that the prevalence rates for symptoms in different body regions were high as compared to the general Iranian population (for neck, back and large joints, p <.0001). The results of multivariate analyses showed that major ergonomic factors associated with musculoskeletal symptoms were loom type, working posture, daily working time and seat type. Based on the results, some general guidelines for designing weaving workstations were developed. A prototype test showed that the new workstation was acceptable for subject tests and that it improved working posture.

Handbook of Research on Literacy and Diversity

ERIC Educational Resources Information Center

Morrow, Lesley Mandel, Ed.; Rueda, Robert, Ed.; Lapp, Diane, Ed.

2009-01-01

This is the first research handbook to address all dimensions of diversity that have an impact on literacy achievement. Leading experts examine how teaching and learning intersect with cultural and language differences and socioeconomic disparities in today's increasingly diverse schools and communities. The volume weaves compelling research…

Reading Assessment and Instruction for All Learners

ERIC Educational Resources Information Center

Schumm, Jeanne Shay, Ed.

2006-01-01

Weaving together the latest knowledge and best practices for teaching children to read, this indispensable text and professional resource provides a complete guide to differentiated instruction for diverse learners. Uniquely integrative, the book places the needs of English language learners and students with disabilities front and center instead…

The Social Weaving of a Reading Atmosphere

ERIC Educational Resources Information Center

Sequeiros, Paula

2011-01-01

This paper discusses how public library readers in Almeida Garrett, Porto, create a reading atmosphere, focusing on meanings associated with aural conditions. Through a qualitative, single case study, ethnographic and interview techniques were applied. Readers' actual practices and discourses, through a theoretical sample, and those of managers,…

Weaving Mathematical Instructional Strategies into Inclusive Settings.

ERIC Educational Resources Information Center

Karp, Karen S.; Voltz, Deborah L.

2000-01-01

This article describes a framework that allows teachers in inclusive elementary settings to interweave instructional strategies from a variety of paradigms to meet individual learning needs in inclusive mathematics classes. Factors to be considered are highlighted and an instructional continuum from more teacher-centered strategies to more…

Epoxy Phosphonate Crosslinkers for Providing Flame Resistance to Cotton Textiles

USDA-ARS?s Scientific Manuscript database

Two new monomers (2-methyl-oxiranylmethyl)-phosphonic acid dimethyl ester (3) and [2-(dimethoxy-phosphorylmethyl)-oxyranylmethyl]-phosphonic acid dimethyl ester (6) were prepared and used with dicyandiamide (7) and citric acid (8) to impart flame resistance to cotton plain weave, twill, and 80:20-co...

Women at Work.

ERIC Educational Resources Information Center

Valiant, Sharon

During the prehistoric era, most advances in society were developed by women. These advances included agriculture, building, weaving, basketry, pottery, woodworking, trading, and domesticating animals. Pottery and basketry allowed for the long-term storage of food and water and permitted humanity to stop living the nomadic life and begin the first…

Weaving Women's Health across Clinical Clerkships.

ERIC Educational Resources Information Center

Magrane, Diane; Ephgrave, Kimberly; Jacobs, Michael; Rusch, Roberta

2000-01-01

Describes three approaches to designing and implementing women's health curricula: (1) adding courses to existing curricula; (2) delegating parts of the curriculum to existing courses; and (3) creating new interdisciplinary curricula. Discusses how each might be applied to the topic of domestic violence. Emphasizes the importance of collaborative…

Science Fair Report: Flight of the Split-Fingered Fastball.

ERIC Educational Resources Information Center

Mitchell, Richard J.

1991-01-01

Reports on the results of an eighth grade student's experiments, conducted with a moving car, concerning the aerodynamics of a baseball in flight. Describes the peculiar diving ability of the split-fingered fastball, as well as the dancing and weaving effect of the knuckleball. (JJK)

Weaving New Retail and Consumer Landscapes in the Scottish Borders

ERIC Educational Resources Information Center

Findlay, Anne; Sparks, Leigh

2008-01-01

New retail locations and formats and changing consumer capabilities and behaviours (including "switching") have encouraged "outshopping" from rural to urban areas. Rural areas have been suffering from a decline in the provision of services, including retailing. One "solution" has been the strengthening of market towns…

77 FR 5580 - Notice of Intent To Seek Approval To Extend an Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-03

... Program supports innovation in the integrative conduct of research, education and knowledge transfer... disciplines, weaving together knowledge creation, knowledge integration, and knowledge transfer. STCs conduct... organizations, and/or other public/private entities. New knowledge thus created is meaningfully linked to...

Weaving a Stronger Fabric for Improved Outcomes

ERIC Educational Resources Information Center

Lobry de Bruyn, Lisa; Prior, Julian; Lenehan, Jo

2014-01-01

Purpose: To explain how training and education events (TEEs) can be designed to increase the likelihood of achieving behavioural objectives. Approach: The approach combined both a quantitative review of evaluation surveys undertaken at the time of the TEE, and qualitative telephone interviews with selected attendees (2025% of the total population…

Doing Academic Writing Differently: A Feminist Bricolage

ERIC Educational Resources Information Center

Handforth, Rachel; Taylor, Carol A.

2016-01-01

This article emerged as the product of a collaboration between two individuals at different stages of our academic careers, one a beginning researcher and the other a senior academic. Written as an experimental "bricolage", the article weaves together two main threads to chart our engagements with feminist research and with writing…

Masters of Weaving: The Complex Role of Special Education Teachers

ERIC Educational Resources Information Center

Hillel Lavian, Rivka

2015-01-01

Special education teachers work under more difficult, more intense, and more demanding conditions than mainstream teachers. Relations between teachers, pupils, and parents are more complex than in mainstream education due to the intensity, intimacy, vulnerability, and commitment involved. Teachers require special skills so they can practice…

Weaving History through the Major

ERIC Educational Resources Information Center

Mayfield, Betty

2014-01-01

The benefits of including the study of the history of mathematics in the education of mathematics majors have been discussed at length elsewhere. Many colleges and universities now offer a History of Mathematics course for mathematics majors, for mathematics education majors, or for general credit. At Hood College, we emphasize our commitment to…

Use of synthetic ground covers to control weeds in blackberries

USDA-ARS?s Scientific Manuscript database

Weed control in blackberries (Rubus spp.) is a serious problem for organic producers and those who wish to reduce their reliance on herbicides. Three landscape fabrics (Dewitt, Texel, and a white polyester weave) and one industrial grade white on black plastic were used for weed control in conjucti...

"Green" School Programs. Research Brief

ERIC Educational Resources Information Center

Johnston, J. Howard

2009-01-01

What are "Green School" programs and how do they benefit students, teachers and the community? Green School programs seek to weave concepts of sustainability and environmental awareness into the social and academic culture of the school community. Green schools are high performance facilities that have been designed, built, renovated operated or…

Higher Order Thinking in the Dance Studio

ERIC Educational Resources Information Center

Moffett, Ann-Thomas

2012-01-01

The author identifies higher order thinking as an essential component of dance training for students of all ages and abilities. Weaving together insights from interviews with experts in the field of dance education with practical pedagogical applications within an Improvisation and Composition class for talented and gifted youth, this article…

10 CFR Appendix D to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Clothes Dryers

Code of Federal Regulations, 2011 CFR

2011-01-01

... granite weave, which is a blended fabric of 50 percent cotton and 50 percent polyester and weighs within... 50 percent polyester fibers. (b) Cloth material that is 24 inches by 36 inches and has been hemmed to...

Silicon-fiber blanket solar-cell array concept

NASA Technical Reports Server (NTRS)

Eliason, J. T.

1973-01-01

Proposed economical manufacture of solar-cell arrays involves parallel, planar weaving of filaments made of doped silicon fibers with diffused radial junction. Each filament is a solar cell connected either in series or parallel with others to form a blanket of deposited grids or attached electrode wire mesh screens.

A Body of Writing, 1990-1999.

ERIC Educational Resources Information Center

Davies, Bronwyn

This book weaves together some of the author's most influential writings of the 1990s to offer a unique engagement with poststructuralism that defies the boundaries between theory and embodied practice. The sophisticated and nuanced discussions of subjectivity, agency, epistemology, feminism, and power are embedded in vital depictions of life…

Multicultural Prism: Voices from the Field. [Volume 1.

ERIC Educational Resources Information Center

Adams, J. Q., Ed.; Welsch, Janice R., Ed.

This book weaves together original essays with several that have been published earlier to address establishing the context for multicultural education, implementing multicultural perspectives in the classroom, and assessing the impact of multicultural education. The book also presents two annotated bibliographies. Following a foreword by J. Q.…

19 CFR 10.16 - Assembly abroad.

Code of Federal Regulations, 2013 CFR

2013-04-01

... steps or steps incidental to assembly. Example 3. The manufacture abroad of cloth on a loom using thread... weaving operation, and the thread or yarn does not qualify for the exemption. However, American-made thread used to sew buttons or garment components is qualified for the exemption because it is used in an...

19 CFR 10.16 - Assembly abroad.

Code of Federal Regulations, 2010 CFR

2010-04-01

... steps or steps incidental to assembly. Example 3. The manufacture abroad of cloth on a loom using thread... weaving operation, and the thread or yarn does not qualify for the exemption. However, American-made thread used to sew buttons or garment components is qualified for the exemption because it is used in an...

19 CFR 10.16 - Assembly abroad.

Code of Federal Regulations, 2011 CFR

2011-04-01

... steps or steps incidental to assembly. Example 3. The manufacture abroad of cloth on a loom using thread... weaving operation, and the thread or yarn does not qualify for the exemption. However, American-made thread used to sew buttons or garment components is qualified for the exemption because it is used in an...

19 CFR 10.16 - Assembly abroad.

Code of Federal Regulations, 2012 CFR

2012-04-01

... steps or steps incidental to assembly. Example 3. The manufacture abroad of cloth on a loom using thread... weaving operation, and the thread or yarn does not qualify for the exemption. However, American-made thread used to sew buttons or garment components is qualified for the exemption because it is used in an...

19 CFR 10.16 - Assembly abroad.

Code of Federal Regulations, 2014 CFR

2014-04-01

... steps or steps incidental to assembly. Example 3. The manufacture abroad of cloth on a loom using thread... weaving operation, and the thread or yarn does not qualify for the exemption. However, American-made thread used to sew buttons or garment components is qualified for the exemption because it is used in an...

Constructs for Web 2.0 Learning Environments: A Theatrical Metaphor

ERIC Educational Resources Information Center

Tu, Chih-Hsiung; Blocher, Michael; Roberts, Gayle

2008-01-01

Web 2.0 technologies empower learners to create personalized and community-based collaborative environments. Social networking technology affords learners to weave their human networks through active connections to understand what we know and we want to know. Social acts that bring out identities, awareness, relationships, connections, and…

Now We Get It! Boosting Comprehension with Collaborative Strategic Reading

ERIC Educational Resources Information Center

Klingner, Janette K.; Vaughn, Sharon; Boardman, Alison; Swanson, Elizabeth

2012-01-01

Collaborative Strategic Reading is an innovative new approach to teaching reading that weaves together two instructional programs: cooperative learning and reading comprehension strategy instruction. In small groups, students work through the four main steps-Preview, "Click and Clunk," Get the Gist, and Wrap Up-helping each other improve…

Felting as Expressive Art Form.

ERIC Educational Resources Information Center

Cirillo, Sandi

1998-01-01

Describes felting as the process of making felt using sheep's wool from fibers without weaving or knitting. Explains that teachers can incorporate felting into a lesson exploring the background behind this process, as an extension of collage or textile arts, as a means to studying abstract art, or in a fashion design unit. (CMK)

Beyond DreamWeaving: Honoring Our Connections.

ERIC Educational Resources Information Center

Russell, Martha M.

DreamWeavers listen for the dreams within themselves and within others. The process of career counseling, career management coaching and career/life planning invites practitioners to consistently listen for the dreams, understand that dreams are visions and that visions guide us to action. This paper highlights how career practitioners are called…

78 FR 56658 - Notice of Solicitation of Applications for Allocation of Tariff Rate Quotas on the Import of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-13

... DEPARTMENT OF COMMERCE International Trade Administration Notice of Solicitation of Applications... Weave Such Fabrics in the United States AGENCY: Department of Commerce, International Trade Administration. ACTION: The Department of Commerce (Department) is soliciting applications for an allocation of...

Electronic Notes.

ERIC Educational Resources Information Center

Krauthamer, Helene

2001-01-01

Describes a workshop used with classes doing Web research for their English papers in a computer lab. Shows how this is a good opportunity for students to learn to find, evaluate, and save Web sources, how to read critically and annotate the sources, and how to weave them into working drafts and avoid plagiarism. (SR)

Blurred Lines: The School Librarian and the Instructional Technology Specialist

ERIC Educational Resources Information Center

Johnston, Melissa P.

2015-01-01

"Empowering Learners: Guidelines for School Library Media Programs" (AASL, 2009) charges school librarians "to play a leading role in weaving such skills throughout the curriculum so that all members of the school community are effective users of ideas and information" (p. 46). Providing leadership in technology integration for…

Deconstructive Misalignment: Archives, Events, and Humanities Approaches in Academic Development

ERIC Educational Resources Information Center

Holmes, Trevor M.; Sutherland, Kathryn A.

2015-01-01

Using poetry, role play, readers' theatre, and creative manipulations of space through yarn and paper weaving, a workshop in 2008 challenged one of educational development's more pervasive and least questioned notions ("constructive alignment" associated most often with the work of John Biggs). This paper describes the reasoning behind…

Rethinking Mathematics: Teaching Social Justice by the Numbers

ERIC Educational Resources Information Center

Gutstein, Eric, Ed.; Peterson, Bob, Ed.

2005-01-01

This unique collection of more than 30 articles shows teachers how to weave social-justice principles throughout the math curriculum, and how to integrate social-justice math into other curricular areas as well. "Rethinking Mathematics" presents teaching ideas, lesson plans and reflections by practicing classroom teachers and distinguished…

Seamless Language Learning: Second Language Learning with Social Media

ERIC Educational Resources Information Center

Wong, Lung-Hsiang; Chai, Ching Sing; Aw, Guat Poh

2017-01-01

This conceptual paper describes a language learning model that applies social media to foster contextualized and connected language learning in communities. The model emphasizes weaving together different forms of language learning activities that take place in different learning contexts to achieve seamless language learning. it promotes social…

Poetry Workshop. Weave Poetry Through Your Day.

ERIC Educational Resources Information Center

Cullinan, Bee

1998-01-01

Presents a poetry across-the-curriculum activity designed to help primary school students build word-recognition skills and an appreciation for the natural world. Students read a poem about polliwogs aloud, discuss the sounds, examine spelling patterns, and investigate scientific details about polliwogs. The poem, "Polliwogs" is included. (SM)

"Drama" and "Nuclear War" as Representative Anecdotes of Burke's Theories of Ontology and Epistemology.

ERIC Educational Resources Information Center

Williams, David Cratis

Using Kenneth Burke's conceptualization of the "representative anecdote," this paper explicates Burke's own theoretical frame. By examining Burke's system through the two anecdotes of "drama" and "nuclear war," the paper demonstrates that Burke weaves together two distinct theoretical threads, one a theory of Being,…

QUALITY ASSURANCE: THE THREAD THAT WEAVES TOGETHER THE FABRIC OF DIVERSE DISCIPLINES

EPA Science Inventory

Mature Quality Assurance (QA) programs do not call for high quality! However, they most often demand known quality. We can intuitively sense quality in our daily lives.

Protection of the environment is, in part, dependent on the quality of data used in decision making. Wh...

Transaction Circles with Digital Texts as a Foundation for Democratic Practices

ERIC Educational Resources Information Center

Brown, Sally

2015-01-01

Transaction circles weave together elements of guided reading and literature circles in an open conversational structure that supports students as agentive learners. Discourse within these circles utilizing digital informational texts assist in the development of democratic practices even in a time when federal mandates limit curricula and…

Weaving Together Student Supports

ERIC Educational Resources Information Center

Benigni, Mark D.; Miller, Bruce A.

2010-01-01

Public schools must be the catalyst for achieving equity in education. Real equity is not simply achieving equality or about ensuring that everyone gets the same resources and receives the same instruction. Equity is about ensuring that all students get what they need to be successful. Fairness is not providing the same resources, instruction, and…

Four Ways.

ERIC Educational Resources Information Center

Dwyer, Mary Ellen; And Others

1984-01-01

Four art activities for high school students are described: (1) weaving using a vegetable sack; (2) creating kaleidoscope designs, from which students selected a unique, basic shape for a personalized belt buckle; (3) making boomerangs which, when thrown, return to the point of departure; and (4) constructing a mosaic in the school hall. (RM)

Performing Narrative Medicine

ERIC Educational Resources Information Center

Langellier, Kristin M.

2009-01-01

In this article, the author weaves narrative medicine and performance together to consider what might it mean to call narrative medicine a performance. To name narrative medicine as performance is to recognize the texts and bodies, the stories and selves, that participate in its practice--patients' and physicians' embodied stories as well as the…

Pre-Service Teachers' Maturing Perceptions of a TPACK-Framed Signature Pedagogy in Science Education

ERIC Educational Resources Information Center

Hechter, Richard P.

2012-01-01

Teacher education programs across North America are transforming. What were once piecemeal programs consisting of often unrelated courses are now becoming coherent and intertwined trajectories toward teacher certification. Part of this transformation can be attributed to the weaving of "signature pedagogies" throughout overarching…

Student Engagement: Key to Personalized Learning

ERIC Educational Resources Information Center

Ferlazzo, Larry

2017-01-01

Personalized learning has the potential to greatly improve student achievement--but realistic teachers know that any instructional strategy will only be effective if students are willing to do the work. That is why Larry Ferlazzo emphasizes the importance of weaving intrinsic motivation into every personalized learning classroom. Four key elements…

Weaving Traditional Magazine and Journal Resources into the Web.

ERIC Educational Resources Information Center

Vesey, Ken

2003-01-01

Describes the winner of the AASL (American Association of School Libraries) Information Technology Pathfinder Award for 2002 in the secondary category, the "Article Finder," a Web-based hyperguide to finding articles in the Lovett School (Georgia) library media center, a customized information portal highlighting the library's resources…

STELLA Supplements Superior Standards in School!

ERIC Educational Resources Information Center

Andrew, Amy

2009-01-01

Known as the "STELLA" (Standards for Teachers of English Language & Literacy in Australia) Standards Framework, there are a set of nine principles which all teachers of English in Australia should aspire to weave into their professional teaching practices. This article describes the journey that Miss Amy Andrew had embarked on in…

Troublemaker: The Education of Chester Finn

ERIC Educational Resources Information Center

Finn, Chester E., Jr.

2008-01-01

"Troublemaker," the memoir of "Education Next" senior editor and veteran education reformer Chester E. "Checker" Finn Jr., weaves into the chronicle of Finn's life and career the broader history of education reform, in which he has played a vital and sometimes rambunctious role. Currently president of the Thomas B.…

Weaving Together Science and English: An Interconnected Model of Language Development for Emergent Bilinguals

ERIC Educational Resources Information Center

Ciechanowski, Kathryn M.

2014-01-01

This research explores third-grade science and language instruction for emergent bilinguals designed through a framework of planning, lessons, and assessment in an interconnected model including content, linguistic features, and functions. Participants were a team of language specialist, classroom teacher, and researcher who designed…

Untangling the Tangled Webs We Weave: A Team Approach to Cyberspace.

ERIC Educational Resources Information Center

Broidy, Ellen; And Others

Working in a cooperative team environment across libraries and job classifications, librarians and support staff at the University of California at Irvine (UCI) have mounted several successful web projects, including two versions of the Libraries' home page, a virtual reference collection, and Science Library "ANTswer Machine." UCI's…

Teacher Knowledge: A Complex Tapestry

ERIC Educational Resources Information Center

Adoniou, Misty

2015-01-01

Teachers need to know a great deal, in many areas and in multiple ways. Teacher knowledge is a complex tapestry, and teachers must successfully weave the multiple threads. In this article, I present a conceptualisation of teacher knowledge that provides a framework for describing the complexity of teacher knowledge. The framework describes three…

Arts Integration: What Is Really Happening in the Elementary Classroom?

ERIC Educational Resources Information Center

LaJevic, Lisa

2013-01-01

Researching how Arts Integration is practiced in a primary school, this article explores how elementary teachers understand, implement, and experience Arts Integration. Weaving together personal experiences, teacher interviews, focus group sessions, classroom observations, and written texts, I investigate how the arts are often devalued in Arts…

Campus on the Hill.

ERIC Educational Resources Information Center

Martin, Frank Edgerton

2002-01-01

Details the University of Cincinnati's campus master plan, designed to overcome deans'"fiefdoms" and make the best use of the limited remaining open space. Three imperatives shaped the plan: siting new buildings to infill the campus fabric rather than taking open space, siting buildings to shape outdoor spaces, and weaving open spaces as…

Educating for Vocation: Weaving Educational Ideas with Institutional Practices

ERIC Educational Resources Information Center

Roels, Shirley J.

2017-01-01

Theologies of vocation are essential in order to explore questions of purpose, values, and direction with college and university students. Given that educational institutions have embedded values and perspectives, some higher education cultures are more effective than others in fostering a student's sense of life calling. In this article, I…

Celebrating the Earth: Stories, Experiences, and Activities.

ERIC Educational Resources Information Center

Livo, Norma J.

Young learners are invited to learn about the natural world through engaging activities that encourage the observation, exploration, and appreciation of nature. Weaving together a stimulating tapestry of folktales, personal narratives, and hands-on activities, this book teaches children about the earth and all of its creatures--birds, plants,…

Weaving Authenticity and Legitimacy: Latina Faculty Peer Mentoring

ERIC Educational Resources Information Center

Núñez, Anne-Marie; Murakami, Elizabeth T.; Gonzales, Leslie D.

2015-01-01

As an alternative to typical top-down mentoring models, the authors advance a conception of peer mentoring that is based on research about collectivist strategies that Latina faculty employ to navigate the academy. The authors advance recommendations for institutional agents to support mentoring for faculty who are members of historically…

The 1996 Carter G. Woodson Book Awards.

ERIC Educational Resources Information Center

Social Education, 1997

1997-01-01

Discusses this year's recipients of the award that honors books dealing with subjects related to U.S. ethnic minorities and race relations in a manner suitable for young readers. The books include the story of a young Navajo girl learning to weave and an account of the Tuskegee airmen. (MJP)

"Outsiders within"? Deconstructing the Educational Administration Scholar

ERIC Educational Resources Information Center

Wilkinson, Jane; Eacott, Scott

2013-01-01

In this paper, we weave the auto-ethnographic narratives of the two authors with Bourdieu's key concepts of "habitus," "field" and "capital," as we seek to bring to a level of explicitness the reflexive lens which has shaped our scholarly work. In particular, we examine the process of becoming educational…

PLCs, DI, & RTI: A Tapestry for School Change

ERIC Educational Resources Information Center

Stoehr, Judy; Banks, Maria; Allen, Linda

2011-01-01

Rather than buying individual books about professional learning communities (PLCs), differentiated instruction (DI), and Response to Intervention (RTI), invest wisely in one resource that synthesizes all three. The text uses a tapestry analogy to weave together these critical topics to form a comprehensive framework for achieving continuous school…

Laban Movement Analysis Approach to Classical Ballet Pedagogy

ERIC Educational Resources Information Center

Whittier, Cadence

2006-01-01

As a Certified Laban Movement Analyst and a classically trained ballet dancer, I consistently weave the Laban Movement Analysis/Bartenieff Fundamentals (LMA/BF) theories and philosophies into the ballet class. This integration assists in: (1) Identifying the qualitative movement elements both in the art of ballet and in the students' dancing…

77 FR 32938 - Narrow Woven Ribbons With Woven Selvedge From Taiwan: Preliminary Results of Antidumping Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-04

..., style, pattern, or weave construction, including but not limited to single-faced satin, double-faced... DEPARTMENT OF COMMERCE International Trade Administration [A-583-844] Narrow Woven Ribbons With Woven Selvedge From Taiwan: Preliminary Results of Antidumping Duty Administrative Review AGENCY: Import...

Expanding Expectations for Narrative Styles in the Context of Dementia

ERIC Educational Resources Information Center

Guendouzi, Jackie; Davis, Boyd H.; Maclagan, Margaret

2015-01-01

This article uses discourse analyses to examine the narrative styles produced by 2 women with a diagnosis of dementia. Because of constrained cognitive resources, people with dementia (PWD) often use alternative strategies to weave their stories into conversations. People with dementia have difficulty in initiating and maintaining a canonical…

The Tapestry of Language Learning: The Individual in the Communicative Classroom.

ERIC Educational Resources Information Center

Scarcella, Robin C.; Oxford, Rebecca L.

The analogy of a tapestry is used to provide instructional techniques and practices to help teachers of English as a Second Language (ESL) "weave" together environmental factors (classroom interaction, input) and learner cognitive, affective, and social characteristics (learning styles, strategies, motivation) according to the needs of the…

The hydroentanglement system of producing nonwoven fabrics of certain specific attributes and functionalities

USDA-ARS?s Scientific Manuscript database

Although the traditional technologies and processes of producing fabric structures, via yarn spinning, weaving, knitting, lacing, tufting, or the like, continue to be the ‘major league’ players in textile manufacturing today, the modern hydroentanglement system, commonly known as “spunlacing,” has a...

Tapping Ancient Roots: Plaited Paper Baskets

ERIC Educational Resources Information Center

Patrick, Jane

2011-01-01

With ancient roots, basket making has been practiced since the earliest civilizations, and according to textile experts, probably pre-dates pottery. This is partly conjecture since few baskets remain. It is through evidence found in clay impressions that the earliest baskets reveal themselves. Basically, basketry construction is like flat weaving.…

Teaching Bioinformatics and Neuroinformatics by Using Free Web-Based Tools

ERIC Educational Resources Information Center

Grisham, William; Schottler, Natalie A.; Valli-Marill, Joanne; Beck, Lisa; Beatty, Jackson

2010-01-01

This completely computer-based module's purpose is to introduce students to bioinformatics resources. We present an easy-to-adopt module that weaves together several important bioinformatic tools so students can grasp how these tools are used in answering research questions. Students integrate information gathered from websites dealing with…

Effectively Addressing Mental Health Issues in Permanency-Focused Child Welfare Practice

ERIC Educational Resources Information Center

Ornelas, Laura A.; Silverstein, Deborah N.; Tan, Sherylle

2007-01-01

Children and families built by adoption or relative caregiving have specialized needs. This paper proposes a rubric for the central elements of permanency-focused mental health services in child welfare practice. Kinship Center provides an innovative mental health service delivery system, weaving foster and adoptive placement programs, adoption…

Hearing the Messages: Integrating Pueblo Philosophy into Academic Life.

ERIC Educational Resources Information Center

Lowery, Christine T.

1997-01-01

A Pueblo woman with a Ph.D. in social welfare research describes her academic journey, weaving a Pueblo cultural perspective into stories of the doctoral program, her dissertation research on life histories of Indian women recovering from substance abuse, her search for an academic position, the merit review ("a hostile act"), and her…

Practical Tips for Increasing Listening Practice Time

ERIC Educational Resources Information Center

McCaughey, Kevin

2015-01-01

Learning a language--like learning to dance ballet, weaving carpets, or playing the saxophone--takes time and practice. In general, it is safe to say that the more practice one gets, the better one will become. This article will help teachers of English reconsider how to think about listening tasks. It will provide guidance for increasing…

Practice What You Teach: Connecting Curriculum & Professional Learning in Schools

ERIC Educational Resources Information Center

Wiener, Ross; Pimentel, Susan

2017-01-01

To improve teaching and advance student learning requires weaving together the curriculum that students engage with every day with the professional learning of teachers. This paper is designed as a resource for system leaders at the district, state, and charter-management organization (CMO) levels looking to improve instructional outcomes for…

States Seek High School Pathways Weaving Academic, Career Options

ERIC Educational Resources Information Center

Sawchuk, Stephen

2013-01-01

Every student at Wheeling High School takes a full academic courseload. Many of the graduates of this 2,000-student school in Wheeling, Illinois, however, also emerge with significant experience in a career field. Those interested in health careers, for example, can work with student-athletes in the school's athletic training facility, earn a…

Trajectories of At-Homeness and Health in Usual Care and Small House Nursing Homes

ERIC Educational Resources Information Center

Molony, Sheila L.; Evans, Lois K.; Jeon, Sangchoon; Rabig, Judith; Straka, Leslie A.

2011-01-01

Background: Long-term care providers across the United States are building innovative environments called "Green House" or small-house nursing homes that weave humanistic person-centered philosophies into clinical care, organizational policies, and built environments. Purpose: To compare and contrast trajectories of at-homeness and health over…

Campfire Stories with George Catlin--An Encounter of Two Cultures.

ERIC Educational Resources Information Center

National Museum of American Art, Washington, DC.

This lesson plan collection focuses on attitudes and opinions held by Native Americans and European Americans about the United States. The lesson plans are arranged in four sections: (1) "Ancestral Lands" (Debating for Land; Making Treaties and Weaving Wampum; Pipestone Quarry and Westward Expansion: Whose Rock Is It Anyway); (2)…

Re-Learning the Traditional Art of Inuit Grass Basket-Making

ERIC Educational Resources Information Center

Cowan, Cindy

2005-01-01

This paper describes an adult learning project to revitalise the traditional Inuit art of weaving grass baskets. The participants involved in the project, all older women who speak an indigenous first language (Inuktitut) and who have limited experience with formal education, largely on their own initiative, undertook the process of successfully…

Representing Latino/a Culture in Introductory Spanish Textbooks.

ERIC Educational Resources Information Center

Elissondo, Guillermina

This paper examines the kinds of visuals that Spanish language textbooks use to legitimize Latino/a culture, noting how different groups are presented and represented by the narratives; how ethnicity, class, gender, age, and sexual inclinations interplay with power relations, and what ideologies weave the textual fabric of foreign language books.…

The Electronic FERPA: Access in the Digital Age

ERIC Educational Resources Information Center

McConahay, Mark; Hanson, Karen; West, Ann; Woodbeck, Dean

2009-01-01

On every college and university campus, common themes weave throughout identity and access management (IAM) and its relationship to Family Educational Rights and Privacy Act (FERPA). Institutions approach IAM differently as there is not a one-size-fits-all solution. Nevertheless, all face common elements. Over the past few years, a number of…

Weaving Geometry and Algebra Together

ERIC Educational Resources Information Center

Cetner, Michelle

2015-01-01

When thinking about student reasoning and sense making, teachers must consider the nature of tasks given to students along with how to plan to use the tasks in the classroom. Students should be presented with tasks in a way that encourages them to draw connections between algebraic and geometric concepts. This article focuses on the idea that it…

EMERGING POLLUTANTS, AND COMMUNICATING THE SCIENCE OF ENVIRONMENTAL CHEMISTRY AND MASS SPECTROMETRY: PHARMACEUTICALS IN THE ENVIRONMENT

EPA Science Inventory

This paper weaves a rnulti-dimensioned perspective of mass spectrometry as a career against the backdrop of mass spectrometry's key role in the past and future of environmental chemistry. Along the way, some insights are offered for better focusing the spotlight on the discipline...

Understanding and integrating native knowledge to determine and identify high quality ash resources

Treesearch

Suzanne Greenlaw; Marla R. Emery; Robin W. Kimmerer; Michael. Bridgen

2010-01-01

Black ash (Fraxinus nigra) is spiritually, economically, and culturally connected to Native American tribes throughout its range. Considered a cultural keystone species, black ash can be pounded and split along its growth rings to produce exceptionally strong and pliable strips to weave into baskets. Black ash harvesters and basketmakers (...

"EMERGING" POLLUTANTS, AND COMMUNICATING THE SCIENCE OF ENVIRONMENTAL CHEMISTRY AND MASS SPECTROMETRY: PHARMACEUTICALS IN THE ENVIRONMENT

EPA Science Inventory

This paper weaves a rnulti-dimensioned perspective of mass spectrometry as a career against the backdrop of mass spectrometry's key role in the past and future of environmental chemistry. Along the way, some insights are offered for better focusing the spotlight on the discipline...

Weaving a Syllaweb: Consideration before Constructing an On-line Syllabus.

ERIC Educational Resources Information Center

Johnston, Joyce P.

This paper explores the practical and philosophical issues involved in Web site construction so that the finished site truly reflects its creator. The author uses the term "syllaweb" for a hyperlinked syllabus and declares that it was an outgrowth of Vannevar Bush's original description of computerized graphical communication as a web,…

Family-School Relations as Social Capital: Chinese Parents in the United States

ERIC Educational Resources Information Center

Wang, Dan

2008-01-01

Guided by both Coleman and Bourdieu's theories on social capital, I interviewed Chinese immigrant parents to understand their experiences in weaving social connections with the school and teachers to benefit their children's education. This study confirms Coleman's argument that human capital in parents will not transfer to the children…

4-H Textile Science Textile Arts Projects.

ERIC Educational Resources Information Center

Scholl, Jan

This packet contains three 4-H textile arts projects for students in the textile sciences area. The projects cover weaving, knitting, and crocheting. Each project provides an overview of what the student will learn, what materials are needed, and suggested projects for the area. Projects can be adapted for beginning, intermediate, or advanced…

Let Me Do It: Children's Art with Less Stress and More Success.

ERIC Educational Resources Information Center

Spears, Jo Ann Lohl

2002-01-01

Offers suggestions for incorporating inexpensive art activities into early childhood classrooms. Suggests activities for children over 3 years in the areas of art using: paint and food coloring, drawing or scribbling, sculpture or construction, weaving and stitching, clay and dough, paper scraps, and broken crayons. Suggests craft activities for…

Dancing on the Bottom Line: An Unruly Cost-Benefit Analysis of Three Academic Development Initiatives

ERIC Educational Resources Information Center

Sword, Helen

2014-01-01

This article offers an unconventional cost-benefit analysis of three academic development initiatives at a large Australasian university: a three-day foundation course for new academics, a series of one-on-one teaching consultations and a two-year postgraduate certificate program. Weaving together qualitative, quantitative and arts-based…

Provisions of Trustworthiness in Critical Narrative Research: Bridging Intersubjectivity and Fidelity

ERIC Educational Resources Information Center

Moss, Glenda

2004-01-01

This paper is a reflective-reflexive examination of provisions of trustworthiness in critical narrative research. The author presents her understanding of provisions of trustworthiness as a science and as an art, and blurs these boundaries as she acknowledges their tension in practice. She weaves between theory and her experience in two…

Inform, Perform, Transform: Modeling In-School Youth Participatory Action Research through Gameplay

ERIC Educational Resources Information Center

Garcia, Antero

2012-01-01

In this article, the author explores youth participatory action research (YPAR) through gameplay. He describes Ask Anansi, an alternate reality game (ARG) played in the "real world" by weaving elements of storytelling and fiction into the environment played as part of class experience. This game which the author created drove the…

24. VIEW INSIDE BRICK ADDITION ON SOUTHWEST END OF ORIGINAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. VIEW INSIDE BRICK ADDITION ON SOUTHWEST END OF ORIGINAL MILL, LOOKING NORTH. NOTE WOOD TRUSSES AND FLUTED COLUMNS (CAST IRON WITH EGYPTIAN REVIVAL CAPITAL). THIS SECTION OF THE MILL WAS PROBABLY PART OF THE WEAVE ROOM ADDITIONS DURING THE 1860s. - Graniteville Mill, Marshall Street, Graniteville, Aiken County, SC

Roles of Frequency, Attitudes, and Multiple Intelligence Modality Surrounding Electricity Content-Based Reader's Theatre

ERIC Educational Resources Information Center

Hosier, Julie Winchester

2009-01-01

Integration of subjects is something elementary teachers must do to insure required objectives are covered. Science-based Reader's Theatre is one way to weave reading into science. This study examined the roles of frequency, attitudes, and Multiple Intelligence modalities surrounding Electricity Content-Based Reader's Theatre. This study used…

Teaching and Learning Health Justice: Best Practices and Recommendations for Innovation

ERIC Educational Resources Information Center

Rentmeester, Christy A.; Chapple, Helen S.; Haddad, Amy M.; Stone, John R.

2016-01-01

We describe the development and implementation of an online graduate bioethics program that weaves a theme of health justice throughout the curriculum. Our account relies on a constructionist model of curriculum development and adult teaching and learning theory. Our curriculum draws upon core values of Jesuit higher education, including content…

Word Weaving: A Storytelling Workbook. Workshop Edition.

ERIC Educational Resources Information Center

Horne, Catharine

Intended to provide a full range of storytelling techniques, this workbook includes 54 stories and their activities. Some stories are introduced with a fanfare and warmup section based on theatre games; some stories are preceded by commentary and source notes; and some folktales are retold with no preliminaries at all. About half of the stories…

Implementation and Modification of an Anatomy-Based Integrated Curriculum

ERIC Educational Resources Information Center

Klement, Brenda J.; Paulsen, Douglas F.; Wineski, Lawrence E.

2017-01-01

Morehouse School of Medicine elected to restructure its first-year medical curriculum by transitioning from a discipline-based to an integrated program. The anatomy course, with regional dissection at its core, served as the backbone for this integration by weaving the content from prior traditional courses into the curriculum around the anatomy…

Marked Difference

ERIC Educational Resources Information Center

Lampela, Laurel

2008-01-01

Helen Cozza is a contemporary artist living in New Mexico who began working as a painter and moved into printmaking. Prevalent in her work is the use of the grid and the patterns created by weaving. The imagery is reminiscent of the environmental deterioration that Cozza observed in Buffalo and Cleveland where she lived for many years. Cozza knew…

Interwoven Story: A Narrative Study of Textiles as Educators

ERIC Educational Resources Information Center

Tremblay-Dion, Catherine-Laura

2017-01-01

Drawing from both narrative research and Joe Kincheloe's work of research bricolage this study inquired into how textiles have served as educator throughout my life. Weaving, as the earliest and most integral of textile fabrications, is particularly featured in this narrative inquiry. A loom, in its most basic form, consists of three components; a…

How the OCLC CORC Service Is Helping Weave Libraries into the Web.

ERIC Educational Resources Information Center

Covert, Kay

2001-01-01

Describes OCLC's CORC (Cooperative Online Resource Catalog) service. As a state-of-the-art Web-based metadata creation system, CORC is optimized for creating bibliographic records and pathfinders for electronic resources. Discusses how libraries are using CORC in technical services, public services, and collection development and explains the…

Weaving Culture and Core Content into FLEX Programs

ERIC Educational Resources Information Center

Schultz, Kennedy M.

2012-01-01

While immersion programs provide some of the greatest benefits to children learning a new language, many school systems have yet to dedicate the financial and personnel resources necessary to plan and implement such programs on a wide scale. In areas where immersion or formal FLES programming does not exist in the schools, often opportunities to…

Mathematics and Water in the Garden: Weaving Mathematics into the Students' Lived Environment

ERIC Educational Resources Information Center

Clarkson, Philip

2010-01-01

In an earlier issue of "Australian Primary Mathematics Classroom," Sparrow discussed the concept of real-world mathematics and the use of mathematics to explore problems in real-life situations. Environmental issues have provided a context that some teachers have used for teaching mathematics. An example of a particular environmental…

1. EXTERIOR VIEW OF HILLSIDE PLANT FROM INTERSECTION OF LINCOLN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EXTERIOR VIEW OF HILLSIDE PLANT FROM INTERSECTION OF LINCOLN STREET AND 2ND AVENUE. HILLSIDE PLANT WAS BUILT AS CALLAWAY MILLS HILLSIDE COTTON MILL (PARK A. DALLIS, 1914-15). THIS TWO-STORY SECTION WAS BUILT AS A WEAVE SHED. - Hillside Cotton Mill, 1300 Brownwood Avenue, La Grange, Troup County, GA

Proceedings of the Annual Technology Literacy Conference. (7th, Alexandria, Virginia, February 6-9, 1992).

ERIC Educational Resources Information Center

Cheek, Dennis, Ed.

The following papers are included in these proceedings: "Weaving Technology and Human Affairs" (B. Hazeltine); "Positivist and Constructivist Understandings about Science and Their Implications for STS Teaching and Learning" (B. Reeves; C. Ney); "A Modular Conceptual Framework for Technology and Work" (D. Blandow); "A Time of Uncertainty: The…

Living Willow Huts

ERIC Educational Resources Information Center

Keeler, Rusty

2007-01-01

Living Willow Huts are inexpensive to make, fun to plant, easy to grow, and make beautiful spaces for children. They involve planting dormant willow shoots in the ground and weaving them into shapes that will sprout and grow over time. People have been creating similar living architecture throughout the world for centuries in the forms of living…

Proposal for Teaching Evolutionary Biology: A Bridge between Research and Educational Practice

ERIC Educational Resources Information Center

Alvarez Pérez, Eréndira; Ruiz Gutiérrez, Rosaura

2016-01-01

We present quantitative results for the doctoral thesis of the first-named author of this article. The objective was to recommend and test a teaching proposal for core knowledge of evolutionary biology in secondary education. The focus of the study is "Problem cores in teaching". The "Weaving evolutionary thinking" teaching…

"Lalaga Faatasi Aua Le Manuia Mo Taeao": To Weave Together for the Success for Tomorrow

ERIC Educational Resources Information Center

Lee, Kerry; Toso, Meripa

2015-01-01

Teacher educators have a very daunting task requiring currency in their discipline, curricular, policy and institutional imperatives as well as pedagogical and cultural issues. Tertiary institutions are facing increasing expectations to cater for and increase retention of underrepresented groups, whilst class sizes increase and face-to-face…

Weaving the Past into the Present by Digitizing Local History

ERIC Educational Resources Information Center

Schlumpf, Kay; Zschernitz, Rob

2007-01-01

Since its humble beginning, Digital Past, a centralized local history digitization initiative at the North Suburban Library System (NSLS), a multitype consortium in Wheeling, Illinois, has now grown into a large centralized collaboration that consists of 32 libraries and a museum as its primary contributors. With Digital Past, there are various…

A Rainbow of Threads

ERIC Educational Resources Information Center

Mack, Stevie

2011-01-01

In the highlands of Guatemala, the Maya Indians weave colorful, vibrant textiles. Many of these beautiful fabrics are used to make traditional clothing for the men, women, and children who live in the rural villages. In Mayan culture, dress is important for more than just keeping warm and covered. It serves as a sort of uniform that immediately…

Weaving the Web into Course Integrated Instruction.

ERIC Educational Resources Information Center

Wallach, Ruth; McCann, Linda

In the fall 1995, a professor teaching an undergraduate course asked the Reference Center at the University of Southern California to conduct a research session on Dante related resources on the Internet, and to show her students how to search the Dartmouth Dante Project. A simple homepage was created for the class, which listed the course…

Weaving a Secure Web around Education: A Guide to Technology Standards and Security.

ERIC Educational Resources Information Center

National Forum on Education Statistics (ED/OERI), Washington, DC.

The purpose of this guidebook is to assist education agencies and organizations--which include state education agencies or state departments of education, school districts, and schools--in the development, maintenance, and standardization of effective Web sites. Also included is a detailed examination of the procedures necessary to provide…

Discourses of Legitimacy: A Love Song to Our Mongrel Selves

ERIC Educational Resources Information Center

Filmer, Alice A.

2009-01-01

In an intervention that blurs methodological boundaries traditionally separating the researcher from the researched, history from poetry, and the personal from the political, the author weaves a narrative account of her Euro-American family's early history in California into a larger set of social and historical events taking place during the…

Peoples, Processes and Patterns: Islam.

ERIC Educational Resources Information Center

Gibbons, Joan; And Others

Designed for use by elementary and secondary teachers but useful to anyone interested in Islamic art, this booklet considers the ways in which design issues have been solved in Islamic cultures, both in the past and the present. The text covers two major areas: aspects of pattern in Islamic weaving and aspects of Islamic tilework. Under weaving…

The Common Thread: Tips for Weaving Philanthropy into the Campus Fabric

ERIC Educational Resources Information Center

Bennett, Gayle

2013-01-01

Like any profession, advancement has its terms of art: "the ask," "prospects," "quiet phase." A relatively new one is "culture of philanthropy." As in, "We need to build a culture of philanthropy at this institution." The general idea is that everyone from the campus CEO to the students understands…

Get 'Em outside

ERIC Educational Resources Information Center

Weise, Lisa

2012-01-01

There is a movement afoot in the nation--one that goes against the trend toward more testing, less recess, and too many standards to fit into the school day. This movement does not ignore standards; rather, it weaves the standards with the places and meanings that are ever-present outside of the classrooms. Place-based education connects students…

Pedagogical Souvenirs: An Art Educator's Reflections on Field Trips as Professional Development

ERIC Educational Resources Information Center

Kushins, Jodi

2015-01-01

This essay explores the nature and importance of field trips as sites for artistic development, intellectual fulfillment, and pedagogical inspiration. The author weaves personal reflections from a professional field trip and experience teaching art education online with creative and pedagogical references to make a case for experiential learning…

Understanding Early Childhood Mental Health: A Practical Guide for Professionals

ERIC Educational Resources Information Center

Summers, Susan Janko, Ed.; Chazan-Cohen, Rachel, Ed.

2012-01-01

Integrating infant mental health services into early education programs leads to better child outcomes and stronger parent-child relationships--the big question is how to do it appropriately and effectively. Clear answers are in this accessible textbook, created to prepare early childhood professionals and programs to weave best practices in…

An Explosion of Creativity in a Remote Egyptian Village.

ERIC Educational Resources Information Center

Osman, Siham A.

1985-01-01

The Egyptian architect Wissa Wassef believed artistry in crafts to be an innate human characteristic that would be universally expressed under the right conditions, i.e., the practice of the craft from early childhood. When he had Egyptian peasant children with no previous art experience weave tapestries, the results astounded the world. (RM)

Weaving Web 2.0 and the Writing Process with Feminist Pedagogy

ERIC Educational Resources Information Center

Zhao, Ruijie

2010-01-01

This dissertation, as a theoretical study, focused on how Web 2.0 technology potentially helps students gain power, knowledge, and agency in the networked learning environment and how feminist pedagogy conceivably facilitates the implementation of Web 2.0 technology to produce an opportune learning environment. Primarily, this study used feminist…

Geographies of Indigenous Leaders: Landscapes and Mindscapes in the Pacific Northwest

ERIC Educational Resources Information Center

Marker, Michael

2015-01-01

This essay features three stories of "place-based" leadership in two Indigenous communities in the Pacific Northwest. Author Michael Marker weaves together stories from Nisga'a Elders in the Nass Valley of British Columbia, Coast Salish Elders in Washington State, and his own experiences as a researcher, teacher educator, and community…

Weaving Strands of Writer Identity: Self as Author and the NNES "Plagiarist"

ERIC Educational Resources Information Center

Ouellette, Mark A.

2008-01-01

While plagiarism is often viewed in terms of ethical binaries, scholars in composition studies have recognized plagiarism as part of literacy practices governing identity construction. In this light, what is at stake is how writers construct identity by positioning stance-claims according to the standards of respective discourse communities. For…

Writing and Dialogue in, and around, a Senior Secondary Literature Classroom

ERIC Educational Resources Information Center

Bellis, Natalie; Garcia, Jessica

2018-01-01

The tradition of teachers engaging in narrative-based inquiry is now well established, as is its value for creating situated knowledge about teaching. This reflexive autobiographical article weaves together narrative accounts around a senior literature classroom environment. The article features two voices: a teacher (Natalie Bellis) and a Year 12…

Narrating a Critical Indigenous Pedagogy of Place: A Literary Métissage

ERIC Educational Resources Information Center

Lowan-Trudeau, Gregory

2017-01-01

This essay responds to a persistent paucity of narrative and Indigenous perspectives in scholarship related to a critical pedagogy of place. In it Gregory Lowan-Trudeau explores interrelated concepts such as diasporic indigeneity, identity, and critical, place-based education and research through a literary métissage that weaves together Western…

Bearing Witness: Poetry by Teachers about Teaching.

ERIC Educational Resources Information Center

Hatcher, Margaret, Ed.

The purpose of this poetry anthology is to create a positive inspirational yet realistic picture of teachers and the very challenging and complex contexts within which they "weave their magic in students' lives" and make contributions to the world. The anthology aims to show how teachers think and feel about teaching, learning, and their…

75 FR 53632 - Narrow Woven Ribbons With Woven Selvedge From Taiwan and the People's Republic of China...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-01

..., style, pattern, or weave construction, including but not limited to single-faced satin, double-faced... DEPARTMENT OF COMMERCE International Trade Administration [A-583-844, A-570-952] Narrow Woven Ribbons With Woven Selvedge From Taiwan and the People's Republic of China: Antidumping Duty Orders AGENCY...

Weaving Curricular Standards into the Language Classroom: An Action Research Study.

ERIC Educational Resources Information Center

Yamada, Yuko; Moeller, Aleidine J.

2001-01-01

This action research study examines the perspectives and voices of students in a postsecondary Japanese class through an authentic project--a pen pal letter exchange. The project's effects on student motivation and learning are analyzed through the lens of the five goals of the national standards: communication, cultures, connections, comparisons,…

Stories in the Cloth: Art Therapy and Narrative Textiles

ERIC Educational Resources Information Center

Garlock, Lisa Raye

2016-01-01

In this article I weave together the relevance of narrative textile work in therapeutic and human rights contexts; showcase Common Threads, an international nonprofit that uses story cloths with survivors of gender-based violence; outline a master's level art therapy course in story cloths; and relate how textiles helped build a sibling…

The Goat in the Rug.

ERIC Educational Resources Information Center

Blood, Charles L.; Link, Martin

Based on the activities of the real Window Rock weaver, Glenmae, and her goat, Geraldine, this illustrated story incorporates authentic details relative to the Navajo art of rug weaving and is designed for children aged four to eight. Capitalizing on the humor inherent in Geraldine's point of view, the story centers on the goat's observation of…

Examining PT3 Projects Designed to Improve Preservice Education

ERIC Educational Resources Information Center

Mims, Clif; Polly, Drew; Shepherd, Craig; Inan, Fethi

2006-01-01

One of the current goals of public education is technology integration. This is witnessed in current educational literature, by the enormous sums of money schools, colleges, and departments of education (SCDEs) spend to purchase equipment and in the emphasis on weaving technology into the fabric of the educational curriculum. As the integration…

Weaving Social Media into a Business Proposal Project

ERIC Educational Resources Information Center

Li, Xiaoli

2012-01-01

Given that students are enthusiastic about social media or even have expertise in some social media tools, the author decided to design a class project in her Writing for Careers (Business Communication) class that integrates social media in terms of content and project management. This article intends to describe such a class project design as…

China starts tapping rich geothermal resources

NASA Astrophysics Data System (ADS)

Guang, D.

1980-09-01

Attention is given to the electric and power installation running on geothermal energy at Yangbajain, Tibet. Other geothermal projects in Tibet, the Yunnan Province and the North China Plain are also outlined. Applications of geothermal energy are described, including the heating of homes and factories, spinning, weaving, paper-making and the making of wine.

Understanding the Complexities of Cognition and Creativity to Reform Higher Education Practice

ERIC Educational Resources Information Center

Welkener, Michelle M.

2013-01-01

This article focuses on the connections between the cognitive dimension of human meaning-making and creativity, using a metaphor from the artistic process of additive sculpture as a framework. The author weaves together various theoretical perspectives about cognition and creativity and shares the promise of recognizing the nexus of these notions…

How the Flowers Came to Be.

ERIC Educational Resources Information Center

Skinner, Linda; Brescia, William, Ed.

The booklet tells the story of Josephine, a little Choctaw girl, who picks wild flowers and hurts her Aunt's feelings. Josephine later learns from her grandmother the importance of respecting nature and how the flowers came to be. The story introduces constellations, how weaving came to the Choctaw, how the sick were prayed for, and why wild…

"It's the Camaraderie": A History of Parent Cooperative Preschools.

ERIC Educational Resources Information Center

Hewes, Dorothy W.

This book offers a comprehensive history of the parent cooperative preschool movement, a unique educational system that attained its peak in the 1950s and 1960s. The book uses interviews with pioneers and current members of parent cooperatives, official documents, periodicals, and scholarly publications to offer a history that weaves the…

A Computational Lens on Design Research

ERIC Educational Resources Information Center

Hoyles, Celia; Noss, Richard

2015-01-01

In this commentary, we briefly review the collective effort of design researchers to weave theory with empirical results, in order to gain a better understanding of the processes of learning. We seek to respond to this challenging agenda by centring on the evolution of one sub-field: namely that which involves investigations within a…

The evolution of an ancient technology

PubMed Central

2017-01-01

We investigate pattern and process in the transmission of traditional weaving cultures in East and Southeast Asia. Our investigation covers a range of scales, from the experiences of individual weavers (‘micro’) to the broad-scale patterns of loom technologies across the region (‘macro’). Using published sources, we build an empirical model of cultural transmission (encompassing individual weavers, the household and the community), focussing on where cultural information resides and how it is replicated and how transmission errors are detected and eliminated. We compare this model with macro-level outcomes in the form of a new dataset of weaving loom technologies across a broad area of East and Southeast Asia. The lineages of technologies that we have uncovered display evidence for branching, hybridization (reticulation), stasis in some lineages, rapid change in others and the coexistence of both simple and complex forms. There are some striking parallels with biological evolution and information theory. There is sufficient detail and resolution in our findings to enable us to begin to critique theoretical models and assumptions that have been produced during the last few decades to describe the evolution of culture. PMID:28573032

DOE Office of Scientific and Technical Information (OSTI.GOV)

Radhakrishnan, Bala; Gorti, Sarma; Babu, Suresh Sudharsanam

Here, we present phase field simulations incorporating energy contributions due to thermodynamics, and anisotropic interfacial and strain energies, to demonstrate the nucleation and growth of multiple variants of alpha from beta in Ti-6Al-4V under isothermal conditions. The simulations focused on the effect of thermodynamic driving force and nucleation rate on the morphology of the transformed alpha assuming that the partitioning of V between beta and alpha is negligible for short isothermal holds. The results indicate that a high nucleation rate favors the formation of the basket-weave structure. However, at a lower nucleation rate the simulations show the intragranular nucleation ofmore » a colony structure by an autocatalytic nucleation mechanism adjacent to a pre-existing alpha variant. New side-plates of the same variant appear to nucleate progressively and grow to form the colony. The isothermal simulation results are used to offer a possible explanation for the transition from a largely basket weave structure to a colony structure inside narrow layer bands occurring during continuous heating and cooling conditions encountered during laser additive manufacturing of Ti-6Al-4V.« less

A novel effective micromixer having horizontal and vertical weaving flow motion

NASA Astrophysics Data System (ADS)

Yoo, Won-Sul; Go, Jung Sang; Park, Seonghun; Park, Sang-Hu

2012-03-01

The need for small-scale product-related biotechnology (BT) is rapidly increasing. An important product among these is high-performance biochips. In these devices, many microchannels are used for separation, filtering and mixing of various materials; therefore, for compactness, these reactions should be carried out in the small space of microfluidic systems. However, there is no turbulence that can induce materials to be mixed or reacted in the microchannel, especially with low Reynolds number laminar flow. Hence, it is difficult to sufficiently mix different materials. To address this problem, we propose the HVW (horizontal and vertical weaving) micromixer having crossed barriers inside of a microchannel, for effective mixing and reacting different materials. From CFD analysis, we have evaluated the mixing mechanism and efficiency of the HVW mixer. In this work, it is shown that the HVW mixer has the maximum mixing efficiency of 89.9% with a short mixing distance of 450 µm at a Reynolds number of 5 with the barrier angle of 30°, when water and water combined with Rhodamine B figment were used as fluids.

Redescription of the orb-weaving spider Gasteracantha geminata (Fabricius, 1798) (Araneae, Araneidae).

PubMed

Sankaran, Pradeep M; Jobi, Malamel J; Sebastian, Pothalil A

2015-02-02

The orb-weaving spider genus Gasteracantha Sundevall, 1833 (Araneidae) is notable for its pronounced sexual size dimorphism. Gasteracantha females are characterized by having a highly sclerotized "spiny" abdomen varying in relative size and number of spines, as well as abdomen dorsally and ventrally provided with varying numbers of sigillae (Cambridge 1879). The genus currently includes 70 described species and 31 subspecies (World Spider Catalog 2014). The Oriental species Gasteracantha geminata (Fabricius, 1798) was originally described from Ramnad (now known as Ramanathapuram) in Tamilnadu State of Southern India based on an unspecified number of female specimen(s). The female of this species has been described and illustrated several times by various authors. Its male is only known from the description of Simon (1895). Simon's original description of the male of G. geminata was supported by two simple but beautiful and informative illustrations: a retrolateral view of the cephalothorax and a dorsal view of the abdomen (Simon 1895, figs. 886, 887). However we lack a clear and detailed description of the male genitalia. The present paper provides detailed redescription of G. geminata and illustrations of the male pedipalp. 

Spontaneous male death during copulation in an orb-weaving spider.

PubMed Central

Foellmer, Matthias W; Fairbairn, Daphne J

2003-01-01

Males of some cannibalistic species of spiders and insects appear to sacrifice themselves by allowing the female to eat them, and the adaptive significance of such drastic terminal reproductive investment has recently been demonstrated for a spider. Typically, the female has to kill the male, but it has been suggested that males of some species in the cannibalistic orb-weaving spider genus Argiope may die in copula without female 'collaboration'. Here, we provide the first experimental evidence to our knowledge of programmed sudden death after onset of copulation in males of the spider Argiope aurantia. Our observations reveal that males invariably die during the insertion of their second pedipalp, regardless of whether they mate with newly moulted, defenceless females or with older mature females that often attack them. We determined experimentally that the death of males is triggered immediately upon insertion of the second palp, when males become unresponsive, and heartbeat ceases within minutes of insertion. We discuss the possible adaptive significance of programmed death during copulation, and argue that male death has evolved in a context other than sexual cannibalism. PMID:14667377

Experimental study of canvas characterization for paintings

NASA Astrophysics Data System (ADS)

Cornelis, Bruno; Dooms, Ann; Munteanu, Adrian; Cornelis, Jan; Schelkens, Peter

2010-02-01

The work described here fits in the context of a larger project on the objective and relevant characterization of paintings and painting canvas through the analysis of multimodal digital images. We captured, amongst others, X-ray images of different canvas types, characterized by a variety of textures and weave patterns (fine and rougher texture; single thread and multiple threads per weave), including raw canvas as well as canvas processed with different primers. In this paper, we study how to characterize the canvas by extracting global features such as average thread width, average distance between successive threads (i.e. thread density) and the spatial distribution of primers. These features are then used to construct a generic model of the canvas structure. Secondly, we investigate whether we can identify different pieces of canvas coming from the same bolt. This is an important element for dating, authentication and identification of restorations. Both the global characteristics mentioned earlier and some local properties (such as deviations from the average pattern model) are used to compare the "fingerprint" of different pieces of cloth coming from the same or different bolts.

GCD TechPort Data Sheets Thermal Protection System Materials (TPSM) Project

NASA Technical Reports Server (NTRS)

Chinnapongse, Ronald L.

2014-01-01

The Thermal Protection System Materials (TPSM) Project consists of three distinct project elements: the 3-Dimensional Multifunctional Ablative Thermal Protection System (3D MAT) project element; the Conformal Ablative Thermal Protection System (CA-TPS) project element; and the Heatshield for Extreme Entry Environment Technology (HEEET) project element. 3D MAT seeks to design, develop and deliver a game changing material solution based on 3-dimensional weaving and resin infusion approach for manufacturing a material that can function as a robust structure as well as a thermal protection system. CA-TPS seeks to develop and deliver a conformal ablative material designed to be efficient and capable of withstanding peak heat flux up to 500 W/ sq cm, peak pressure up to 0.4 atm, and shear up to 500 Pa. HEEET is developing a new ablative TPS that takes advantage of state-of-the-art 3D weaving technologies and traditional manufacturing processes to infuse woven preforms with a resin, machine them to shape, and assemble them as a tiled solution on the entry vehicle substructure or heatshield.

The evolution of an ancient technology.

PubMed

Buckley, Christopher D; Boudot, Eric

2017-05-01

We investigate pattern and process in the transmission of traditional weaving cultures in East and Southeast Asia. Our investigation covers a range of scales, from the experiences of individual weavers ('micro') to the broad-scale patterns of loom technologies across the region ('macro'). Using published sources, we build an empirical model of cultural transmission (encompassing individual weavers, the household and the community), focussing on where cultural information resides and how it is replicated and how transmission errors are detected and eliminated. We compare this model with macro-level outcomes in the form of a new dataset of weaving loom technologies across a broad area of East and Southeast Asia. The lineages of technologies that we have uncovered display evidence for branching, hybridization (reticulation), stasis in some lineages, rapid change in others and the coexistence of both simple and complex forms. There are some striking parallels with biological evolution and information theory. There is sufficient detail and resolution in our findings to enable us to begin to critique theoretical models and assumptions that have been produced during the last few decades to describe the evolution of culture.

Highly efficient and completely flexible fiber-shaped dye-sensitized solar cell based on TiO2 nanotube array

NASA Astrophysics Data System (ADS)

Lv, Zhibin; Yu, Jiefeng; Wu, Hongwei; Shang, Jian; Wang, Dan; Hou, Shaocong; Fu, Yongping; Wu, Kai; Zou, Dechun

2012-02-01

A type of highly efficient completely flexible fiber-shaped solar cell based on TiO2 nanotube array is successfully prepared. Under air mass 1.5G (100 mW cm-2) illumination conditions, the photoelectric conversion efficiency of the solar cell approaches 7%, the highest among all fiber-shaped cells based on TiO2 nanotube arrays and the first completely flexible fiber-shaped DSSC. The fiber-shaped solar cell demonstrates good flexibility, which makes it suitable for modularization using weaving technologies.A type of highly efficient completely flexible fiber-shaped solar cell based on TiO2 nanotube array is successfully prepared. Under air mass 1.5G (100 mW cm-2) illumination conditions, the photoelectric conversion efficiency of the solar cell approaches 7%, the highest among all fiber-shaped cells based on TiO2 nanotube arrays and the first completely flexible fiber-shaped DSSC. The fiber-shaped solar cell demonstrates good flexibility, which makes it suitable for modularization using weaving technologies. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr11532h

High-Toughness Silk Produced by a Transgenic Silkworm Expressing Spider (Araneus ventricosus) Dragline Silk Protein

PubMed Central

Kuwana, Yoshihiko; Sezutsu, Hideki; Nakajima, Ken-ichi; Tamada, Yasushi; Kojima, Katsura

2014-01-01

Spider dragline silk is a natural fiber that has excellent tensile properties; however, it is difficult to produce artificially as a long, strong fiber. Here, the spider (Araneus ventricosus) dragline protein gene was cloned and a transgenic silkworm was generated, that expressed the fusion protein of the fibroin heavy chain and spider dragline protein in cocoon silk. The spider silk protein content ranged from 0.37 to 0.61% w/w (1.4–2.4 mol%) native silkworm fibroin. Using a good silk-producing strain, C515, as the transgenic silkworm can make the raw silk from its cocoons for the first time. The tensile characteristics (toughness) of the raw silk improved by 53% after the introduction of spider dragline silk protein; the improvement depended on the quantity of the expressed spider dragline protein. To demonstrate the commercial feasibility for machine reeling, weaving, and sewing, we used the transgenic spider silk to weave a vest and scarf; this was the first application of spider silk fibers from transgenic silkworms. PMID:25162624

Oldest true orb-weaving spider (Araneae: Araneidae)

PubMed Central

Penney, David; Ortuño, Vicente M

2006-01-01

The aerial orb web woven by spiders of the family Araneidae typifies these organisms to laypersons and scientists alike. Here we describe the oldest fossil species of this family, which is preserved in amber from Álava, Spain and represents the first record of Araneidae from the Lower Cretaceous. The fossils provide direct evidence that all three major orb web weaving families: Araneidae, Tetragnathidae and Uloboridae had evolved by this time, confirming the antiquity of the use of this remarkable structure as a prey capture strategy by spiders. Given the complex and stereotyped movements that all orb weavers use to construct their webs, there is little question regarding their common origin, which must have occurred in the Jurassic or earlier. Thus, various forms of this formidable prey capture mechanism were already in place by the time of the explosive Cretaceous co-radiation of angiosperms and their flying insect pollinators. This permitted a similar co-radiation of spider predators with their flying insect prey, presumably without the need for a ‘catch-up lag phase’ for the spiders. PMID:17148427

High-toughness silk produced by a transgenic silkworm expressing spider (Araneus ventricosus) dragline silk protein.

PubMed

Kuwana, Yoshihiko; Sezutsu, Hideki; Nakajima, Ken-ichi; Tamada, Yasushi; Kojima, Katsura

2014-01-01

Spider dragline silk is a natural fiber that has excellent tensile properties; however, it is difficult to produce artificially as a long, strong fiber. Here, the spider (Araneus ventricosus) dragline protein gene was cloned and a transgenic silkworm was generated, that expressed the fusion protein of the fibroin heavy chain and spider dragline protein in cocoon silk. The spider silk protein content ranged from 0.37 to 0.61% w/w (1.4-2.4 mol%) native silkworm fibroin. Using a good silk-producing strain, C515, as the transgenic silkworm can make the raw silk from its cocoons for the first time. The tensile characteristics (toughness) of the raw silk improved by 53% after the introduction of spider dragline silk protein; the improvement depended on the quantity of the expressed spider dragline protein. To demonstrate the commercial feasibility for machine reeling, weaving, and sewing, we used the transgenic spider silk to weave a vest and scarf; this was the first application of spider silk fibers from transgenic silkworms.

Herbivory in Spiders: The Importance of Pollen for Orb-Weavers

PubMed Central

Eggs, Benjamin; Sanders, Dirk

2013-01-01

Orb-weaving spiders (Araneidae) are commonly regarded as generalist insect predators but resources provided by plants such as pollen may be an important dietary supplementation. Their webs snare insect prey, but can also trap aerial plankton like pollen and fungal spores. When recycling their orb webs, the spiders may therefore also feed on adhering pollen grains or fungal spores via extraoral digestion. In this study we measured stable isotope ratios in the bodies of two araneid species (Aculepeira ceropegia and Araneus diadematus), their potential prey and pollen to determine the relative contribution of pollen to their diet. We found that about 25% of juvenile orb-weaving spiders’ diet consisted of pollen, the other 75% of flying insects, mainly small dipterans and hymenopterans. The pollen grains in our study were too large to be taken up accidentally by the spiders and had first to be digested extraorally by enzymes in an active act of consumption. Therefore, pollen can be seen as a substantial component of the spiders’ diet. This finding suggests that these spiders need to be classified as omnivores rather than pure carnivores. PMID:24312430

Herbivory in spiders: the importance of pollen for orb-weavers.

PubMed

Eggs, Benjamin; Sanders, Dirk

2013-01-01

Orb-weaving spiders (Araneidae) are commonly regarded as generalist insect predators but resources provided by plants such as pollen may be an important dietary supplementation. Their webs snare insect prey, but can also trap aerial plankton like pollen and fungal spores. When recycling their orb webs, the spiders may therefore also feed on adhering pollen grains or fungal spores via extraoral digestion. In this study we measured stable isotope ratios in the bodies of two araneid species (Aculepeira ceropegia and Araneus diadematus), their potential prey and pollen to determine the relative contribution of pollen to their diet. We found that about 25% of juvenile orb-weaving spiders' diet consisted of pollen, the other 75% of flying insects, mainly small dipterans and hymenopterans. The pollen grains in our study were too large to be taken up accidentally by the spiders and had first to be digested extraorally by enzymes in an active act of consumption. Therefore, pollen can be seen as a substantial component of the spiders' diet. This finding suggests that these spiders need to be classified as omnivores rather than pure carnivores.

The effect of warp tension on the colour of jacquard fabric made with different weaves structures

NASA Astrophysics Data System (ADS)

Karnoub, A.; Kadi, N.; Holmudd, O.; Peterson, J.; Skrifvars, M.

2017-10-01

The aims of this paper is to demonstrate the effect of warp tension on fabric colour for several types of weaves structures, and found a relationship between them. The image analyse technique used to determine the proportion of yarns colour appearance, the advantage of this techniques is the rapidity and reliability. The woven fabric samples are consisting of a polyester warp yarn with continuous filaments and density of 33 end/cm, a polypropylene weft yarn with a density of 24 pick/cm, and the warp tension ranged between 12-22 cN/tex. The experimental results demonstrated the effect of the warp tension on the colour of fabric, and this effect is related to several factors, where the large proportion of warp appearance leads to larger effect on fabric colour. The difference in the value of colour differences ΔEcmc is larger is in the range 16 to 20 cN/tex of warp tension. Using statistical methods, a mathematical model to calculate the amount of the colour difference ΔEcmc caused by the change in warp tension had been proposed.

Effects of assumed tow architecture on the predicted moduli and stresses in woven composites

NASA Technical Reports Server (NTRS)

Chapman, Clinton Dane

1994-01-01

This study deals with the effect of assumed tow architecture on the elastic material properties and stress distributions of plain weave woven composites. Specifically, the examination of how a cross-section is assumed to sweep-out the tows of the composite is examined in great detail. The two methods studied are extrusion and translation. This effect is also examined to determine how sensitive this assumption is to changes in waviness ratio. 3D finite elements were used to study a T300/Epoxy plain weave composite with symmetrically stacked mats. 1/32nd of the unit cell is shown to be adequate for analysis of this type of configuration with the appropriate set of boundary conditions. At low waviness, results indicate that for prediction of elastic properties, either method is adequate. At high waviness, certain elastic properties become more sensitive to the method used. Stress distributions at high waviness ratio are shown to vary greatly depending on the type of loading applied. At low waviness, both methods produce similar results.

Using active colloids as machines to weave and braid on the micrometer scale

NASA Astrophysics Data System (ADS)

Goodrich, Carl P.; Brenner, Michael P.

2017-01-01

Controlling motion at the microscopic scale is a fundamental goal in the development of biologically inspired systems. We show that the motion of active, self-propelled colloids can be sufficiently controlled for use as a tool to assemble complex structures such as braids and weaves out of microscopic filaments. Unlike typical self-assembly paradigms, these structures are held together by geometric constraints rather than adhesive bonds. The out-of-equilibrium assembly that we propose involves precisely controlling the 2D motion of active colloids so that their path has a nontrivial topology. We demonstrate with proof-of-principle Brownian dynamics simulations that, when the colloids are attached to long semiflexible filaments, this motion causes the filaments to braid. The ability of the active particles to provide sufficient force necessary to bend the filaments into a braid depends on a number of factors, including the self-propulsion mechanism, the properties of the filament, and the maximum curvature in the braid. Our work demonstrates that nonequilibrium assembly pathways can be designed using active particles.

The Fabric of the Universe: Exploring the Cosmic Web in 3D Prints and Woven Textiles

NASA Astrophysics Data System (ADS)

Diemer, Benedikt; Facio, Isaac

2017-05-01

We introduce The Fabric of the Universe, an art and science collaboration focused on exploring the cosmic web of dark matter with unconventional techniques and materials. We discuss two of our projects in detail. First, we describe a pipeline for translating three-dimensional (3D) density structures from N-body simulations into solid surfaces suitable for 3D printing, and present prints of a cosmological volume and of the infall region around a massive cluster halo. In these models, we discover wall-like features that are invisible in two-dimensional projections. Going beyond the sheer visualization of simulation data, we undertake an exploration of the cosmic web as a three-dimensional woven textile. To this end, we develop experimental 3D weaving techniques to create sphere-like and filamentary shapes and radically simplify a region of the cosmic web into a set of filaments and halos. We translate the resulting tree structure into a series of commands that can be executed by a digital weaving machine, and present a large-scale textile installation.

Using active colloids as machines to weave and braid on the micrometer scale

PubMed Central

Goodrich, Carl P.; Brenner, Michael P.

2017-01-01

Controlling motion at the microscopic scale is a fundamental goal in the development of biologically inspired systems. We show that the motion of active, self-propelled colloids can be sufficiently controlled for use as a tool to assemble complex structures such as braids and weaves out of microscopic filaments. Unlike typical self-assembly paradigms, these structures are held together by geometric constraints rather than adhesive bonds. The out-of-equilibrium assembly that we propose involves precisely controlling the 2D motion of active colloids so that their path has a nontrivial topology. We demonstrate with proof-of-principle Brownian dynamics simulations that, when the colloids are attached to long semiflexible filaments, this motion causes the filaments to braid. The ability of the active particles to provide sufficient force necessary to bend the filaments into a braid depends on a number of factors, including the self-propulsion mechanism, the properties of the filament, and the maximum curvature in the braid. Our work demonstrates that nonequilibrium assembly pathways can be designed using active particles. PMID:28034922

PDF Weaving - Linking Inventory Data and Monte Carlo Uncertainty Analysis in the Study of how Disturbance Affects Forest Carbon Storage

NASA Astrophysics Data System (ADS)

Healey, S. P.; Patterson, P.; Garrard, C.

2014-12-01

Altered disturbance regimes are likely a primary mechanism by which a changing climate will affect storage of carbon in forested ecosystems. Accordingly, the National Forest System (NFS) has been mandated to assess the role of disturbance (harvests, fires, insects, etc.) on carbon storage in each of its planning units. We have developed a process which combines 1990-era maps of forest structure and composition with high-quality maps of subsequent disturbance type and magnitude to track the impact of disturbance on carbon storage. This process, called the Forest Carbon Management Framework (ForCaMF), uses the maps to apply empirically calibrated carbon dynamics built into a widely used management tool, the Forest Vegetation Simulator (FVS). While ForCaMF offers locally specific insights into the effect of historical or hypothetical disturbance trends on carbon storage, its dependence upon the interaction of several maps and a carbon model poses a complex challenge in terms of tracking uncertainty. Monte Carlo analysis is an attractive option for tracking the combined effects of error in several constituent inputs as they impact overall uncertainty. Monte Carlo methods iteratively simulate alternative values for each input and quantify how much outputs vary as a result. Variation of each input is controlled by a Probability Density Function (PDF). We introduce a technique called "PDF Weaving," which constructs PDFs that ensure that simulated uncertainty precisely aligns with uncertainty estimates that can be derived from inventory data. This hard link with inventory data (derived in this case from FIA - the US Forest Service Forest Inventory and Analysis program) both provides empirical calibration and establishes consistency with other types of assessments (e.g., habitat and water) for which NFS depends upon FIA data. Results from the NFS Northern Region will be used to illustrate PDF weaving and insights gained from ForCaMF about the role of disturbance in carbon storage.

Loss of legs: is it or not a handicap for an orb-weaving spider?

NASA Astrophysics Data System (ADS)

Pasquet, Alain; Anotaux, Mylène; Leborgne, Raymond

2011-07-01

Leg loss is a common phenomenon in spiders, and according to the species 5% to 40% of the adults can present at least one missing leg. There is no possibility of regeneration after adult moult and the animal must manage with its missing appendages until its death. With the loss of one or more legs, female orb-weaving spiders can be penalized twice: firstly, because the legs are necessary for web construction and secondly, the legs are essential for the control of the prey after its interception by the web. During development, spiders may be also penalized because regeneration has energetic costs that take away resources for survival, growth and reproduction. All these consequences should influence negatively the development of the spider and thus its fitness. We investigated the impact of leg loss in the orb-weaving spider, Zygiella x-notata by studying its frequency in a natural population and web building and prey capture behaviours in laboratory. In field populations, 9.5% to 13%, of the adult females presented the loss of one or more legs; the majority of individuals had lost only one leg (in 48% of cases, a first one). Leg loss seems to affect all the adult spiders, as there is no difference of mass between intact spiders and those with missing leg. Data obtained with laboratory-reared spiders, showed that the loss of legs due to the moult is rare (less than 1%). Considering changes in web design, spiders with missing legs decreased their silk investment, increased the distance between spiral turns but did not change the capture surface of the web. Under our laboratory experimental conditions, spiders with one or two lost legs did not present any difference in prey capture efficiency. In laboratory conditions, spiders with lost leg(s) did not show any difference in egg sac production or in longevity (adult lifespan) compared to intact spiders.

Receiving care for intimate partner violence in primary care: Barriers and enablers for women participating in the weave randomised controlled trial.

PubMed

O'Doherty, Lorna; Taket, Ann; Valpied, Jodie; Hegarty, Kelsey

2016-07-01

Interventions in health settings for intimate partner violence (IPV) are being increasingly recognised as part of a response to addressing this global public health problem. However, interventions targeting this sensitive social phenomenon are complex and highly susceptible to context. This study aimed to elucidate factors involved in women's uptake of a counselling intervention delivered by family doctors in the weave primary care trial (Victoria, Australia). We analysed associations between women's and doctors' baseline characteristics and uptake of the intervention. We interviewed a random selection of 20 women from an intervention group women to explore cognitions relating to intervention uptake. Interviews were audio-recorded, transcribed, coded in NVivo 10 and analysed using the theory of planned behaviour (TPB). Abuse severity and socio-demographic characteristics (apart from current relationship status) were unrelated to uptake of counselling (67/137 attended sessions). Favourable doctor communication was strongly associated with attendance. Eight themes emerged, including four sets of beliefs that influenced attitudes to uptake: (i) awareness of the abuse and readiness for help; (ii) weave as an avenue to help; (iii) doctor's communication; and (iv) role in providing care for IPV; and four sets of beliefs regarding women's control over uptake: (v) emotional health, (vi) doctors' time, (vii) managing the disclosure process and (viii) viewing primary care as a safe option. This study has identified factors that can promote the implementation and evaluation of primary care-based IPV interventions, which are relevant across health research settings, for example, ensuring fit between implementation strategies and characteristics of the target group (such as range in readiness for intervention). On practice implications, providers' communication remains a key issue for engaging women. A key message arising from this work concerns the critical role of primary care and health services more broadly in reaching victims of domestic violence, and providing immediate and ongoing support (depending on the healthcare context). Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparing treatment effects of oral THC on simulated and on-the-road driving performance: testing the validity of driving simulator drug research.

PubMed

Veldstra, J L; Bosker, W M; de Waard, D; Ramaekers, J G; Brookhuis, K A

2015-08-01

The driving simulator provides a safe and controlled environment for testing driving behaviour efficiently. The question is whether it is sensitive to detect drug-induced effects. The primary aim of the current study was to investigate the sensitivity of the driving simulator for detecting drug effects. As a case in point, we investigated the dose-related effects of oral ∆(9)-tetrahydrocannabinol (THC), i.e. dronabinol, on simulator and on-the-road driving performance in equally demanding driving tasks. Twenty-four experienced driver participants were treated with dronabinol (Marinol®; 10 and 20 mg) and placebo. Dose-related effects of the drug on the ability to keep a vehicle in lane (weaving) and to follow the speed changes of a lead car (car following) were compared within subjects for on-the-road versus in-simulator driving. Additionally, the outcomes of equivalence testing to alcohol-induced effects were investigated. Treatment effects found on weaving when driving in the simulator were comparable to treatment effects found when driving on the road. The effect after 10 mg dronabinol was however less strong in the simulator than on the road and inter-individual variance seemed higher in the simulator. There was, however, a differential treatment effect of dronabinol on reactions to speed changes of a lead car (car following) when driving on the road versus when driving in the simulator. The driving simulator was proven to be sensitive for demonstrating dronabinol-induced effects particularly at higher doses. Treatment effects of dronabinol on weaving were comparable with driving on the road but inter-individual variability seemed higher in the simulator than on the road which may have potential effects on the clinical inferences made from simulator driving. Car following on the road and in the simulator were, however, not comparable.

Thermostructural Properties Of Sic/Sic Panels With 2.5d And 3d Fiber Architectures

NASA Technical Reports Server (NTRS)

Yun, H. M.; DeCarlo, J. A.; Bhatt, R. H.; Jaskowiak, M. H.

2005-01-01

CMC hot-section components in advanced engines for power and propulsion will typically require high cracking strength, high ultimate strength and strain, high creep- rupture resistance, and high thermal conductivity in all directions. In the past, NASA has demonstrated fabrication of a variety of SiC/SiC flat panels and round tubes with various 2D fiber architectures using the high-modulus high-performance Sylramic-iBN Sic fiber and Sic-based matrices derived by CVI, MI, and/or PIP processes. The thermo- mechanical properties of these CMC have shown state-of-the-art performance, but primarily in the in-plane directions. Currently NASA is extending the thermostructural capability of these SiC/SiC systems in the thru-thickness direction by using various 2.5D and 3D fiber architectures. NASA is also using specially designed fabrication steps to optimize the properties of the BN-based interphase and Sic-based matrices. In this study, Sylramic-iBN/SiC panels with 2D plain weave, 2.5D satin weave, 2.5D ply-to-ply interlock weave, and 3D angle interlock fiber architectures, all woven at AITI, were fabricated using matrix densification routes previously established between NASA and GEPSC for CVI-MI processes and between NASA and Starfire-Systems for PIP processes. Introduction of the 2.5 D fiber architecture along with an improved matrix process was found to increase inter-laminar tensile strength from 1.5 -2 to 3 - 4 ksi and thru-thickness thermal conductivity from 15-20 to 30-35 BTU/ft.hr.F with minimal reduction in in-plane strength and creep-rupture properties. Such improvements should reduce thermal stresses and increase the thermostructural operating envelope for SiC/SiC engine components. These results are analyzed to offer general guidelines for selecting fiber architectures and constituent processes for high-performance SiC/SiC engine components.

MDMA ("ecstasy"), methamphetamine and their combination: long-term changes in social interaction and neurochemistry in the rat.

PubMed

Clemens, Kelly J; Van Nieuwenhuyzen, Petra S; Li, Kong M; Cornish, Jennifer L; Hunt, Glenn E; McGregor, Iain S

2004-05-01

3,4-Methylenedioxymethamphetamine (MDMA) and methamphetamine (METH) are illicit drugs that are increasingly used in combination. The acute and long-term effects of MDMA/METH combinations are largely uncharacterised. The current study investigated the behavioural, thermal and neurotoxic effects of MDMA and METH when given alone or in combined low doses. Male rats received four injections, one every 2 h, of vehicle, MDMA (2.5 or 5 mg/kg per injection), METH (2.5 or 5 mg/kg per injection) or combined MDMA/METH (1.25+1.25 mg/kg per injection or 2+2 mg/kg per injection). Drugs were given at an ambient temperature of 28 degrees C to simulate hot nightclub conditions. Body temperature, locomotor activity and head-weaving were assessed during acute drug administration while social interaction, anxiety-related behavior on the emergence test and neurochemical parameters were assessed 4-7 weeks later. All treatments acutely increased locomotor activity, while pronounced head-weaving was seen with both MDMA/METH treatments and the higher dose METH treatment. Acute hyperthermia was greatest with the higher dose MDMA/METH treatment and was also seen with MDMA but not METH treatment. Several weeks after drug administration, both MDMA/METH groups, both METH groups and the higher dose MDMA group showed decreased social interaction relative to controls, while both MDMA/METH groups and the lower dose MDMA group showed increased anxiety-like behaviour on the emergence test. MDMA treatment caused 5-HT and 5-HIAA depletion in several brain regions, while METH treatment reduced dopamine in the prefrontal cortex. Combined MDMA/METH treatment caused 5-HT and 5-HIAA depletion in several brain regions and a unique depletion of dopamine and DOPAC in the striatum. These results suggest that MDMA and METH in combination may have greater adverse acute effects (head-weaving, body temperature) and long-term effects (decreased social interaction, increased emergence anxiety, dopamine depletion) than equivalent doses of either drug alone.

Fatigue of a 3D Orthogonal Non-crimp Woven Polymer Matrix Composite at Elevated Temperature

NASA Astrophysics Data System (ADS)

Wilkinson, M. P.; Ruggles-Wrenn, M. B.

2017-12-01

Tension-tension fatigue behavior of two polymer matrix composites (PMCs) was studied at elevated temperature. The two PMCs consist of the NRPE polyimide matrix reinforced with carbon fibers, but have different fiber architectures: the 3D PMC is a singly-ply non-crimp 3D orthogonal weave composite and the 2D PMC, a laminated composite reinforced with 15 plies of an eight harness satin weave (8HSW) fabric. In order to assess the performance and suitability of the two composites for use in aerospace components designed to contain high-temperature environments, mechanical tests were performed under temperature conditions simulating the actual operating conditions. In all elevated temperature tests performed in this work, one side of the test specimen was at 329 °C while the other side was open to ambient laboratory air. The tensile stress-strain behavior of the two composites was investigated and the tensile properties measured for both on-axis (0/90) and off-axis (±45) fiber orientations. Elevated temperature had little effect on the on-axis tensile properties of the two composites. The off-axis tensile strength of both PMCs decreased slightly at elevated temperature. Tension-tension fatigue tests were conducted at elevated temperature at a frequency of 1.0 Hz with a ratio of minimum stress to maximum stress of R = 0.05. Fatigue run-out was defined as 2 × 105 cycles. Both strain accumulation and modulus evolution during cycling were analyzed for each fatigue test. The laminated 2D PMC exhibited better fatigue resistance than the 3D composite. Specimens that achieved fatigue run-out were subjected to tensile tests to failure to characterize the retained tensile properties. Post-test examination under optical microscope revealed severe delamination in the laminated 2D PMC. The non-crimp 3D orthogonal weave composite offered improved delamination resistance.

Fiber and fabric solar cells by directly weaving carbon nanotube yarns with CdSe nanowire-based electrodes

NASA Astrophysics Data System (ADS)

Zhang, Luhui; Shi, Enzheng; Ji, Chunyan; Li, Zhen; Li, Peixu; Shang, Yuanyuan; Li, Yibin; Wei, Jinquan; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai; Cao, Anyuan

2012-07-01

Electrode materials are key components for fiber solar cells, and when combined with active layers (for light absorption and charge generation) in appropriate ways, they enable design and fabrication of efficient and innovative device structures. Here, we apply carbon nanotube yarns as counter electrodes in combination with CdSe nanowire-grafted primary electrodes (Ti wire) for making fiber and fabric-shaped photoelectrochemical cells with power conversion efficiencies in the range 1% to 2.9%. The spun-twist long nanotube yarns possess both good electrical conductivity and mechanical flexibility compared to conventional metal wires or carbon fibers, which facilitate fabrication of solar cells with versatile configurations. A unique feature of our process is that instead of making individual fiber cells, we directly weave single or multiple nanotube yarns with primary electrodes into a functional fabric. Our results demonstrate promising applications of semiconducting nanowires and carbon nanotubes in woven photovoltaics.Electrode materials are key components for fiber solar cells, and when combined with active layers (for light absorption and charge generation) in appropriate ways, they enable design and fabrication of efficient and innovative device structures. Here, we apply carbon nanotube yarns as counter electrodes in combination with CdSe nanowire-grafted primary electrodes (Ti wire) for making fiber and fabric-shaped photoelectrochemical cells with power conversion efficiencies in the range 1% to 2.9%. The spun-twist long nanotube yarns possess both good electrical conductivity and mechanical flexibility compared to conventional metal wires or carbon fibers, which facilitate fabrication of solar cells with versatile configurations. A unique feature of our process is that instead of making individual fiber cells, we directly weave single or multiple nanotube yarns with primary electrodes into a functional fabric. Our results demonstrate promising applications of semiconducting nanowires and carbon nanotubes in woven photovoltaics. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr31440a

Production And Characterization Of Synthetic Spider Silks Based On Nephila Clavipes Major Ampullate Silk Proteins

NASA Astrophysics Data System (ADS)

An, Bo

The extraordinary mechanical properties of orb-weaving spider silks have served spiders for over 400 million years. However, only in the late 20th century did we start to understand the molecular nature of spider silk that contributes to its incredible properties as biomaterials. Among all seven types of spider silks, major ampullate silk from typical orb-weaving spiders is the toughest of all, it consists of primarily two proteins: MaSp1 and MaSp2. Variable ratios and conserved motifs of these two proteins in all the native spider silks demonstrate the significant role of MaSp1 and MaSp2 in controlling the mechanical properties of the fiber. The amino acid sequences of the orb weaving spider silk proteins have remained almost unchanged for more than 100 million years. Interestingly, MaSp1 and MaSp2 are the only two components in all studied dragline silk fibers from these spiders. The mechanical properties of native dragline silk vary slightly between species, which are believed to relate to the ratio of MaSp1 to MaSp2 in the silk. Both of these facts clearly indicate the importance of these two proteins to the mechanical properties of the fiber. Various types of synthetic spider silk fibers have been produced and studied in an effort to mass-produce man-made fibers with qualities comparable to native spider silk. To investigate the roles of MaSp1 and MaSp2 in silk fiber, synthetic MaSp1 (major abundant protein in Nephila clavipes major ampullate silks) only fibers, MaSp1/MaSp2 protein mixture fibers and chimeric protein fibers with both MaSp1 and MaSp2 sequence features have been produced and tested for mechanical properties. Solid-State Nuclear Magnetic Resonance was used to characterize the structure of silk fibers and reveal the relation between fiber spatial structure and mechanical properties.

Next-day effects of ramelteon (8 mg), zopiclone (7.5 mg), and placebo on highway driving performance, memory functioning, psychomotor performance, and mood in healthy adult subjects.

PubMed

Mets, Monique A J; de Vries, Juna M; de Senerpont Domis, Lieke M; Volkerts, Edmund R; Olivier, Berend; Verster, Joris C

2011-10-01

To evaluate the next-morning residual effects of ramelteon (8 mg), zopiclone (7.5 mg), and placebo on driving performance, memory functioning, psychomotor performance, and mood in healthy adult subjects following bedtime dosing and a middle of the night awakening. Single-center, randomized, double-blind, double-dummy, placebo-controlled, crossover study. Utrecht University, The Netherlands. 30 healthy volunteers (15 males and 15 females). a single dose of ramelteon (8 mg), zopiclone (7.5 mg), and placebo, administered at bedtime. A balance test was performed at night. Other tests were performed the following morning, 8.5 h after administration. Subjects performed a 100-km highway driving test in normal traffic. Primary outcome measure was the standard deviation of the lateral position (SDLP), i.e., the weaving of the car. After driving, cognitive, memory, and psychomotor tests were performed and mood was assessed. SDLP was significantly increased after the intake of ramelteon (+2.2 cm) and zopiclone (+2.9 cm). Ramelteon and zopiclone produced significant impairment on reaction time (P<0.024) in the Sternberg Memory Scanning Test, slow (P<0.007) and fast (P<0.010) tracking, reaction speed (P<0.015) and tracking (P<0.001) in the Divided Attention Test, and delayed recall (P<0.032) in the Word Learning Test. In contrast to ramelteon, zopiclone additionally impaired performance on the Digit Symbol Substitution Test (P<0.001) and the balance test (P<0.001). Ramelteon (8 mg) and zopiclone (7.5 mg) significantly impaired driving performance, cognitive, memory, and psychomotor performance the morning following bedtime administration. In contrast to zopiclone, ramelteon produced no balance impairments. CLINICAL TRIAL IDENTIFIER: NCT00319215 (www.clinicaltrials.gov).

Telling Stories That Are Needed: An Interview with Christopher Myers. Breakfast Speaker Interview

ERIC Educational Resources Information Center

Adomat, Donna Sayers; Lowery, Ruth McKoy; Fain, Jeanne Gilliam

2016-01-01

Christopher Myers won acclaim at a young age as a vibrant illustrator of children's picturebooks. In this interview, Myers discusses how he has advocated for diversity in children's literature through themes that weave throughout his writing and illustration, collaborations with other artists, and his participation in the communities of artists,…

Steering Performance, Tactical Vehicles

DTIC Science & Technology

2015-07-29

5 4.1 General Vehicle and Test Characterization ........................... 5 4.2 Weave Test...able to be driven in a straight line without steer input (i.e., “ hands free”). If the vehicle pulls in either direction, the alignment should be...Evaluation Center (AEC) prior to using military personnel as test participants. 4. TEST PROCEDURES. 4.1 General Vehicle and Test

Paradigm Shift in Education: Weaving Social-Emotional Learning into Language and Literacy Instruction

ERIC Educational Resources Information Center

Dresser, Rocio

2013-01-01

This paper first outlines some of the challenges students and teachers are facing in schools around the country. These challenges include social issues such as violence, drugs and bulling. This coupled with the fact that many instructional programs follow the cognitive-only model and the current push for standardized testing has had a negative…

Weaving the Tapestry: A Student Affairs Perspective on the Leadership Research Agenda

ERIC Educational Resources Information Center

Komives, Susan R.

2013-01-01

The tapestry of leadership development has a long history in American higher education. As a faculty member for the last 26 years of my career teaching the history of student affairs and higher education and studying college student leadership, I enjoyed examining perspectives on the evolution of leadership development and how it grew from being…

Develop a Business Plan. Phase 1. Information Accumulation and Integration

DTIC Science & Technology

1992-02-01

INTEGRATION EXHIBIT VIII I I 3 Behind the Price Tag of a S73.00 Skirt Poly/ coton skidr wholesale price. S35.00: reail price. S73.00. Behind the Price Tag... Finishing SpinningI Technology & Weaving Technology 1 Quality Government Regulations1 Flexibility I I IEXCERPTED FROM: 16th ANNUAL RETAIL/SOFT GOODS BUSINESS

Equity in Standards-Based Elementary Mathematics Classrooms. Weaving Gender Equity into Math Reform.

ERIC Educational Resources Information Center

Perez, Christina

This article discusses the issue of equity in standards-based elementary mathematics classrooms. It is argued that while some of the gaps in mathematics achievement have slowly diminished (e.g., differences in mathematics grades and participation rates between girls and boys in K-12 education have decreased), others remain intractable. Other…

21 CFR 155.190 - Canned tomatoes.

Code of Federal Regulations, 2012 CFR

2012-04-01

... container so as to distribute the contents over the meshes of a circular sieve which has previously been weighed. The diameter of the sieve used is 20.3 centimeters (8 inches) if the quantity of the contents of... is 1.4 kilograms (3 pounds) or more. The meshes of such sieve are made by so weaving wire of 1.4 mm...

21 CFR 155.190 - Canned tomatoes.

Code of Federal Regulations, 2013 CFR

2013-04-01

... container so as to distribute the contents over the meshes of a circular sieve which has previously been weighed. The diameter of the sieve used is 20.3 centimeters (8 inches) if the quantity of the contents of... is 1.4 kilograms (3 pounds) or more. The meshes of such sieve are made by so weaving wire of 1.4 mm...

21 CFR 155.190 - Canned tomatoes.

Code of Federal Regulations, 2014 CFR

2014-04-01

... container so as to distribute the contents over the meshes of a circular sieve which has previously been weighed. The diameter of the sieve used is 20.3 centimeters (8 inches) if the quantity of the contents of... is 1.4 kilograms (3 pounds) or more. The meshes of such sieve are made by so weaving wire of 1.4 mm...

Second Language Learning with the Story Maze Task: Examining the Training Effect of Weaving through Stories

ERIC Educational Resources Information Center

Enkin, Elizabeth

2016-01-01

The maze task is a psycholinguistic experimental procedure that measures real-time incremental sentence processing. The task has recently been tested as a language learning tool with promising results. Therefore, the present study examines the merits of a contextualized version of this task: the story maze. The findings are consistent with…

Indians Weaving in Cyberspace Indigenous Urban Youth Cultures, Identities and Politics of Languages

ERIC Educational Resources Information Center

Jimenez Quispe, Luz

2013-01-01

This study is aimed at analyzing how contemporary urban Aymara youth hip hoppers and bloggers are creating their identities and are producing discourses in texts and lyrics to contest racist and colonial discourses. The research is situated in Bolivia, which is currently engaged in a cultural and political revolution supported by Indigenous…

75 FR 75664 - Determination Under the Textile and Apparel Commercial Availability Provision of the Dominican...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-06

.../or staple fiber; textured and/or non- textured). Yarn Size(s): Various. Thread Count (warp): 43 to 56 ends per cm. Thread Count (weft): 29 to 38 filling pics per cm. Weave Type: Woven twill. Fabric Weight...-dyed. Finishing Processes: Napped on both sides. Janet E. Heinzen, Acting Chairman, Committee for the...

Language of Physics, Language of Math: Disciplinary Culture and Dynamic Epistemology

ERIC Educational Resources Information Center

Redish, Edward F.; Kuo, Eric

2015-01-01

Mathematics is a critical part of much scientific research. Physics in particular weaves math extensively into its instruction beginning in high school. Despite much research on the learning of both physics and math, the problem of how to effectively include math in physics in a way that reaches most students remains unsolved. In this paper, we…

True Teaching Expertise: The Weaving Together of Theory and Practice

ERIC Educational Resources Information Center

Mascio, Bryan

2016-01-01

How do we strengthen the teaching profession? This question weighs on many educators, researchers, politicians, and parents. The public discourse around teaching often feels very negative; it does not clearly define teaching expertise, but it does reflect a very clear belief that many teachers just do not have it. In this article, a former…

Tensile and Laterally Confined Compression Properties of Various 3-Dimensional (3-D) Woven Composites

DTIC Science & Technology

2014-11-01

such as orthogonal (Z- fiber) weave, layer-to-layer, and angle interlock. Figure 1 provides an example of 2 different types of 3-D woven structures...o.~os~~~o. t Deflection (in) (c) 90° Orientation 18 6.4 LCC Test Specimen Failure Analysis LCC posttest failure analysis was conducted

Polymer infiltration studies

NASA Technical Reports Server (NTRS)

Marchello, Joseph M.

1992-01-01

The preparation is reported of carbon fiber composites using advanced polymer resins. Current and ongoing research activities include: powder towpreg process; weaving, braiding and stitching dry powder prepreg; advanced tow placement; and customized ATP towpreg. The goal of these studies is to produce advanced composite materials for automated part fabrication using textile and robotics technology in the manufacture of subsonic and supersonic aircraft.

Connecting Readers and Writers with Books: Weaving Literature into the School Community.

ERIC Educational Resources Information Center

Harwayne, Shelley; Mandel, Amy; Mayer, Pam; Rhodes, Roberta Pantal; Siegman, Lisa; Werner, Pat

1998-01-01

Argues that the best books will inspire children to pause and think deeply about their own lives and lives of others. Offers brief descriptions of 37 books for children and young readers, including: picture books that promote rich classroom conversations; poetry collections; books to grow up on; picture books for the youngest students; historical…

Helping the Homeless in School and out

ERIC Educational Resources Information Center

Holgersson-Shorter, Helena

2010-01-01

Homeless children can be hard to identify and even harder to help. But teachers can do a great deal to make sure that they do not fall through the cracks. Teachers of highly mobile students must develop the skills to make these children and youth feel welcome while quickly weaving them into classroom routines. They must rapidly assess new…

Death, Murder, and Mayhem: Stories of Violence and Healing on the Plains

ERIC Educational Resources Information Center

Maher, Susan Naramore

2009-01-01

Unexpected, dramatic stories of death have left deep marks on the physical landscape and in the cultural psyche since humans first began to weave narrative from the Plains. When scholars and writers converged in Omaha, Nebraska for the 34th Interdisciplinary Symposium of the Center for Great Plains Center, many stories received scholarly and…

Sharing the Arts of the Blue Ridge Mountains. Final Report, February 1977-January 1978.

ERIC Educational Resources Information Center

Holman, Martha; Gailey, Lamar

Designed to utilize basic skills and develop a vocational or vocational skills, eight adult basic education modules were developed which highlight authentic Blue Ridge Mountain crafts. Modules provide instruction in apple dolls, braided rugs, candles, caning, corn shuck dolls, pottery, quilting, and weaving (see Note). Selection of the crafts was…

The Simultaneity of Experience: Cultural Identity, Magical Realism and the Artefactual in Digital Storytelling

ERIC Educational Resources Information Center

Honeyford, Michelle A.

2013-01-01

This paper explores how students, as multimodal storytellers, can weave powerful narratives blending modes, genres, artefacts and literary conventions to represent the real and imagined in their lives. Part of a larger ethnographic case study of student writing in a middle years class for immigrant students learning English as an additional…

Co-Opting Science: A Preliminary Study of How Students Invoke Science in Value-Laden Discussions

ERIC Educational Resources Information Center

Nielsen, Jan Alexis

2012-01-01

Letting students deliberate on socio-scientific issues is a tricky affair. It is yet unclear how to assess whether, or even support that, students weave science facts into value-laden socio-scientific deliberations without committing the naturalistic fallacy of deducing "ought" from "is". As a preliminary step, this study…

ACHP | News | ACHP Business Meeting Feb. 17 in Washington, D.C.

Science.gov Websites

- America's Great Outdoors Initiative report issued Developing a 21st Century Conservation Agenda - America's Great Outdoors Initiative report issued On Feb. 16, President Obama unveiled the report titled " involved in development of the report and will play a role in its implementation to help weave cultural

Physical Development: Indoor Motor Activities

ERIC Educational Resources Information Center

Strickland, Eric

2005-01-01

In this article, the author features creative ways to fit a lot of movement and fun inside the classroom when there is bad weather. He suggests that, to be creative in the classroom, one can create crawling tunnels for children by moving chairs away from tables and draping sheets or towels over their tops and sides. Or one can weave an obstacle…

Teaching the Moving Child: OT Insights That Will Transform Your K-3 Classroom

ERIC Educational Resources Information Center

Berkey, Sybil M.

2009-01-01

Because sensorimotor and environmental factors have a profound effect on children's learning, every teacher should know how to weave strategies from occupational therapy (OT) into their everyday instruction. This is the guidebook K-3 teachers need to "think like an OT"--and form effective partnerships with OTs in their schools--so all students can…

Multimodal Literacy Narratives: Weaving the Threads of Young Children's Identity through the Arts

ERIC Educational Resources Information Center

Binder, Marni; Kotsopoulos, Sally

2011-01-01

The current study examines how children develop multimodal narratives through the construction of quilt squares and I Am poetry. Creating visual narratives through the use of personal artifacts lays the foundation for this artistic multiple literacy experience. The study focuses on the process and growth that a diverse group of kindergarten…

Weaving Imagination into an Academic Framework: Attitudes, Assignments, and Assessments

ERIC Educational Resources Information Center

Miller, Jeanetta

2009-01-01

The author believes that imagination is alive in the high school classroom, but it is pale and sickly, suffering from a long decline in which teachers have confined it to its most decorous forms of expression--inference and interpretation--and become ambiguous about whether or not it is truly welcome. To rouse imagination in the high school…

Walking Pathways toward Becoming a Culturally Competent Evaluator: Boundaries, Borderlands, and Border Crossings

ERIC Educational Resources Information Center

Symonette, Hazel

2004-01-01

In this article, the author shares insights derived from her journey as an evaluation practitioner and as a capacity-building evaluation facilitator committed to demystifying evaluation as a core development resource. The author weaves in some foundational stories that have shaped and informed her path. Through her work and praxis, she has been…

Weaving Emotional Intelligence into a Home Visiting Model

ERIC Educational Resources Information Center

Enson, Beth; Imberger, Jaci

2017-01-01

This article details the impact of Emotional Intelligence (EI) training on the 10-year evolution of the Taos First Steps Home Visiting program. While EI has become standard fare in corporate training and practice, it is less well known in the world of early childhood services. This article highlights interviews with key personnel, both in-house…

Antihistamines and driving safety.

PubMed

O'Hanlon, J F

1988-10-27

The results of two placebo-controlled driving performance studies confirm laboratory data showing that the nonsedating antihistamine terfenadine does not influence the driving performance of users. The amplitude of vehicle weaving calculated for drivers who received this agent did not differ from control values. Neither terfenadine nor loratadine, another nonsedating antihistamine, potentiated the adverse effects of alcohol on driving performance.

Weaving a Virtual Story--Creating Book Trailers 101

ERIC Educational Resources Information Center

Bates, Naomi

2012-01-01

Book trailers are fast becoming today's marketing technique for newly published books. They have changed the way students select books, and trailers meet the expectations of today's teens who have been brought up on graphic visuals. Book trailers are also quite new, starting as a trend only about four years ago. Since then, they have proliferated,…

Weaving a Web of Support for Students: Assessing ENLACE New Mexico

ERIC Educational Resources Information Center

Excelencia in Education (NJ1), 2009

2009-01-01

In a state where the majority of the population is minority, how youth maneuver through the educational system plays a determining role in the economic well-being of the state. ENLACE New Mexico was created in 2001 to empower the community, students and educators to affect positive change in the public educational system, leading to increased…

Weaving the Web into Your Campaign

ERIC Educational Resources Information Center

Broman, Claudia

2009-01-01

Like anything else, there are good fundraising campaign Web sites and bad fundraising campaign Web sites. The author took a closer look at fundraising campaign sites to see if her intuitive judgments about these could be translated into a logical, research-supported set of best practices. She set up a study that gauged the ease of use and…

Weaving RIE with "Te Whariki": Re-Thinking Family Involvement in Assessment of Learning Dispositions

ERIC Educational Resources Information Center

Cooper, Maria; Hedges, Helen; Dixon, Helen

2014-01-01

Families play important roles in children's learning. Yet, teachers' values and beliefs may sway how families may participate in assessment of their child's learning within early childhood education. This paper reports on a qualitative case study in a New Zealand early childhood setting that explored teachers' views about involving families in…

Herbicide treaments can improve your forest

Treesearch

James H. Miller

1989-01-01

When you plant a young pine stand after harvest, you mimic nature's seeding of the area. Then we often stand back and let nature take its course. Newly planted seedlings must divide their meager energy on two battlefronts: They must push and weave their roots through the tangle already there. At the same time, they must precariously struggle up through layers...

Children of Deb Koh: Young Life in an Iranian Village.

ERIC Educational Resources Information Center

Friedl, Erika

This book is based on ethnographic research carried out between 1965 and 1994 during eight visits to a tribal region in southwest Iran. The book weaves together local practices, cognitive categories, folklore, and anecdotes concerning all aspects of growing up to illuminate the world of children in the village of Deh Koh. The book describes how…

Beyond the Core: Peer Observation Brings Common Core to Vocational and Electives Classes

ERIC Educational Resources Information Center

Thurber Rasmussen, Harriette

2014-01-01

This article describes how a Washington State School District increased professional learning around the Common Core State Standards. The challenge was how to establish a way for career and technical education and electives teachers to learn and apply Common Core in their classes. Weaving Common Core literacy standards into vocational and…

Young Children's Imaginative Play: Is It Valued in Montessori Classrooms?

ERIC Educational Resources Information Center

Soundy, Cathleen S.

2009-01-01

The main purpose of this article is to describe the nature of imaginary play in Montessori classrooms. A transcript from a train ride shows how young children imagine and recreate ideas from their real world experiences and weave them into original new accounts. The author discusses how the play-like action of dramatizing "The Caboose Who Got…

Attitude and Passion: Becoming a Teacher in Early Childhood Education and Care

ERIC Educational Resources Information Center

Maier-Höfer, Claudia

2015-01-01

By focusing on a collective aesthetics based on sensation and affect, researchers, especially in Stockholm, Sweden, are exploring a pedagogy that opens up space for assemblages of desire, acknowledging the expressions of children who transform themselves and their milieus into a weave of bodies, spaces, signs and media. By analysing this pedagogy,…

Beauty and Precision: Weaving Complex Educational Technology Projects with Visual Instructional Design Languages

ERIC Educational Resources Information Center

Derntl, Michael; Parrish, Patrick; Botturi, Luca

2010-01-01

Instructional design and technology products result from many options and constraints. On the one hand, solutions should be creative, effective and flexible; on the other hand, developers and instructors need precise guidance and details on what to do during development and implementation. Communication of and about designs is supported by design…

Weaving It All Together: Meeting Standards, Motivating Students.

ERIC Educational Resources Information Center

Van Horn, Leigh

2002-01-01

Notes the author vowed to prove to herself and to her students that they could meet and exceed the state standards, that they could succeed on any test, and that they could do it while engaging in authentic, context-based reading, writing, speaking, listening, thinking, viewing, and visually representing. Discusses units of study based upon a…

High-Poverty Urban High School Students' Plans for Higher Education: Weaving Their Own Safety Nets

ERIC Educational Resources Information Center

Cilesiz, Sebnem; Drotos, Stephanie M.

2016-01-01

This qualitative study investigates high-poverty urban high school students' views of and plans regarding higher education, using Bourdieu's theory of reproduction in education as theoretical framework. Interview data from 76 students from six high-poverty urban schools in a metropolitan area in the Midwestern United States were analyzed using…

Weaving through Words: Using the Arts To Teach Reading Comprehension Strategies.

ERIC Educational Resources Information Center

Mantione, Roberta D.; Smead, Sabine

This book shows teachers how to help their learners take an active role in becoming strategic thinkers and readers and how to develop meaningful lessons to aid students in their comprehension of text. The book delineates an arts-integrated curriculum that helps teachers teach reading comprehension strategies. It is an in-depth look at the effects…

Seeking the "Truth" in the Stories We Tell: The Role of Critical Race Epistemology in Higher Education Research

ERIC Educational Resources Information Center

Espino, Michelle M.

2012-01-01

This article focuses on how critical race theory informed the author's epistemological perspective and methodological approach as she analyzed Mexican American educational narratives and formulated her identity as a scholar. Using a storytelling technique employed in CRT, the author weaves together her position as the translator of participants'…

Weaving Indigenous Agricultural Knowledge with Formal Education to Enhance Community Food Security: School Competition as a Pedagogical Space in Rural Anchetty, India

ERIC Educational Resources Information Center

Shukla, Shailesh; Barkman, Janna; Patel, Kirit

2017-01-01

Like many socially and economically disadvantaged farming communities around the world, the Anchetty region of Tamil Nadu, India, has been experiencing serious food security challenges mainly due to the loss of traditional foods such as small millets and associated crops (SMAC) and associated indigenous agricultural knowledge (IAK). Drawing on…

An Anishinaabe Tribalography: Investigating and Interweaving Conceptions of Identity during the 1910s on the White Earth Reservation

ERIC Educational Resources Information Center

Doerfler, Jill

2009-01-01

In this article the author uses tribalography as a methodology and connects multiple elements in a textual weaving that constructs an Anishinaabe tribalography. As an Anishinaabe tribalography, this work will follow in the tradition set forth by Gerald Vizenor and Gordon Henry, who, as Kimberly Blaeser asserts, "shift and reshift their…

The ABCs of Teaching Alphabet Knowledge: Affordances and Challenges of "Weaving" Visible and Invisible Pedagogies

ERIC Educational Resources Information Center

Exley, Beryl; Richard-Bossez, Ariane

2013-01-01

As researchers interested in the pursuit of high-quality/high-equity literacy learning outcomes, the authors focus on the learning experiences of five early years French students, with a special regard for those who are already considered as being at risk of educational failure. The authors narrow the empirical focus to a single lesson on a…

Brackish Bayou Blood: Weaving Mixed-Blood Indian-Creole Identity outside the Written Record

ERIC Educational Resources Information Center

Cranford-Gomez, L. Rain

2008-01-01

As a child on the Gulf of Mexico, evacuation to higher ground for floods, hurricanes, and tornado warnings were common. At the end of August 2005, Hurricane Katrina ravaged the homelands of this author's father and grandfather in Louisiana. Hundreds of miles of wetlands, already threatened, were turned to open water; vital brackish waters were…

Caught in the Act: Integrative Studies Where I Least Expected It

ERIC Educational Resources Information Center

Williams, Jeff

2013-01-01

Weaving together stories from history, as well as his own experience, Mr. Williams speaks about how critical public works and policy questions cannot be solved by people trained in one discipline in isolation--arguing that the hyper-specialization of the 20th century swung the pendulum too far. He closes with a reminder of how integrative studies…

The Parent-Child Relationship Competencies: How Three Infant-Parent Psychotherapists Find Paths into Diverse Infant-Family Landscapes

ERIC Educational Resources Information Center

St. John, Maria Seymour

2016-01-01

This article weaves the stories of three practitioner-family relationships and describes how the Parent-Child Relationship Competencies (PCRCs; St. John, 2010) function as a map for assessment and treatment planning. The PCRCs are a set of culturally variable yet universal bi-directional (parent-to-child and child-to-parent) relational capacities…

There-apy: The Use of Task, Imagery, and Symbolism To Connect the Inner and Outer Worlds.

ERIC Educational Resources Information Center

Eisenstein-Naveh, A. Rosa

2001-01-01

Presents a model of therapy called there-apy, which weaves together the use of task, symbolism, and imagery into an ongoing process. Concrete tasks take on symbolic meaning, and symbolism gets actualized through achieving concrete tasks. There-apy connects the individual's outside and inside worlds and often involves the partner or family in the…

"La Universidad De La Vida": A Pedagogy Built to Last

ERIC Educational Resources Information Center

Guajardo, Miguel A.; Guajardo, Francisco J.

2017-01-01

This article weaves the life of a Mexican laborer, who with his wife brought his family to the United States and mentored two university professors, as they became activists in their craft. The professors honor their father through a reflective process where they share and make sense of a series of stories that describe their Papi's experience in…

Transformative Learning in Human Resource Development: Successes in Scholarly Practitioner Applications--Conflict Management, Discursive Processes in Diversity and Leadership Development

ERIC Educational Resources Information Center

Fisher-Yoshida, Beth; Geller, Kathy D.; Wasserman, Ilene C.

2005-01-01

Today's complex global environment calls for leaders to be agile decision makers, engage in critical self-reflection, integrate reflection with action, and partner with those who are different in significant ways. These capabilities and skills are the core qualities of transformative learning. This paper weaves research findings that explore…

It's Not All Ancient History Now: Connecting the Past by Weaving a Threaded Historical Concept

ERIC Educational Resources Information Center

Endacott, Jason

2005-01-01

Proving history's relevance to students is a daunting task that social studies educators face everyday as they create lesson plans that they hope will spark their students' interest in learning about the past. Few educators would argue that demonstrating the relevance of the objectives toward which they are teaching is an unnecessary duty. Perhaps…

Weaving Knowledges: The Development of Empowering Intercultural Learning Spaces for Smallholder Farmers in Papua New Guinea

ERIC Educational Resources Information Center

Pamphilon, Barbara

2015-01-01

Since the early 1970s there has been increasing interest in effective adult education systems and practices as a core foundation for capacity building in developing countries. This paper presents the philosophy behind the concept of an "intercultural learning space" and argues its relevance for such adult learners. Drawing on work in…

Role of School Leadership and Climate in Student Achievement: The Mediating Role of Parental Involvement

ERIC Educational Resources Information Center

Alhosani, Abdulraheem Ali; Singh, Sanjay Kumar; Al Nahyan, Moza Tahnoon

2017-01-01

Purpose: The purpose of this paper is to develop a conceptual model on students' academic achievement that is well grounded in the academic research in the domain. The paper aims to weave together the divergent research findings into a comprehensive model for use by all the stakeholders. Design/methodology/approach: It is a literature review-based…

For Loretta: A Black Woman Literacy Scholar's Journey to Prioritizing Self-Preservation and Black Feminist-Womanist Storytelling

ERIC Educational Resources Information Center

Baker-Bell, April

2017-01-01

In this article, I used "Black feminist-womanist" storytelling to weave together stories from my childhood and early years on the tenure track to illuminate how Black female language and literacy practices and the strongblackwoman trope develop across a life span. Through these stories, I illustrate how I existed, resisted, and persisted…

A Tangled Weave: Tracing Outcomes of Education in Rural Women's Lives in North India

ERIC Educational Resources Information Center

Ghose, Malini; Mullick, Disha

2015-01-01

This paper is based on the findings of a research study which traced 56 rural women learners 15 years after they had participated in an empowerment and education programme in North India. It attempts to understand, from the perspectives of women from marginalised communities, the ways in which participating in the programme had been empowering for…

Making Precarious Immigrant Families and Weaving the Danish Welfare Nation-State Fabric 1970-2010

ERIC Educational Resources Information Center

Padovan-Özdemir, Marta; Moldenhawer, Bolette

2017-01-01

This article explores the making of immigrant families as precarious elements in the governing of the population's welfare within the Danish welfare nation-state since the 1970s. The emphasis is on how immigrant families became a problem of welfare governing, and what knowledge practices and welfare techniques emerged as problem-solving responses.…

Critiquing Child-Centred Pedagogy to Bring Children and Early Childhood Educators into the Centre of a Democratic Pedagogy

ERIC Educational Resources Information Center

Langford, Rachel

2010-01-01

Child-centred pedagogy is both an enduring approach and a revered concept in Western-based teacher preparation. This article weaves together major critiques of child-centred pedagogy that draw on critical feminist, postmodernist and post-structural theories. These critiques have particular relevance for conceptualizing what it can mean to be, and…

Effects of Weave Styles and Crimp Gradients on Damage Tolerance and Energy-Absorption Capacities of Woven Kevlar/Epoxy Composites

DTIC Science & Technology

2015-09-01

Technology Office ( Neil J. Dubois (00T1)) and the Office of Naval Research. The principal investigator was Paul V. Cavallaro (Code 7023). The...Office (RDRL-RO-EN (D. Stepp, W. Mullins)) 2 Navy Clothing and Textile Research Facility, Natick, MA (B. Avellini, L. Caulfield, T. Hart, C. Heath

The quarter-power scaling model does not imply size-invariant hydraulic resistance in plants

Treesearch

Annikki Makela; Harry T. Valentine

2006-01-01

West, Brown, and Enquist (1997, 1999) propose an integrated model of the structure and allometry of plant vascular systems, which has come to be known as the 'WBE model' (Enquist, 2002). The WBE model weaves together area-preserving branching (Leonardo da Vinci), elastic similarity (Greenhill, 1881), the constant ratio of foliage mass to sapwood area (...

Navigating the Structures of Elementary School in the United States and Japan: An Ethnography of the Particular

ERIC Educational Resources Information Center

Damrow, Amy

2014-01-01

This study uses an ecological framework to map one Japanese child's transition between elementary school life in the United States and Japan. I privilege the child's perspective while weaving in parent and teacher views, as well as observation and document data. Implicit and explicit expectations in the focal student's classrooms and schools are…

Following a river wherever it goes: beneath the surface of mountain streams.

Treesearch

Jonathan Thompson; Sally Duncan

2004-01-01

The flow of a mountain stream is difficult to follow, especially when it weaves in and out of the channel, flowing through streambanks and seeping through the streambed. Flowing belowground, the stream water mixes with ground water in the riparian aquifer before reemerging in the channel, sometime later and somewhere further downstream. Underground, the water undergoes...

Textile Arts of India, Curriculum Project. Fulbright Hays Summer Seminar Abroad 1995 (India).

ERIC Educational Resources Information Center

Myers, Barbara

This interdisciplinary unit focuses on five techniques found in the textile arts of India: tie-dye, embroidery, applique, block printing, and weaving. The unit is designed for students in third through sixth grades but could be adapted to other levels. This unit could be incorporated with a study of India's land, history, and geography. The…

Art of the Folk: Mexican Heritage through Arts and Crafts for Boys and Girls.

ERIC Educational Resources Information Center

Linse, Barbara

Instructions for a variety of activities relating to Mexican culture are provided, with brief descriptive and historical notes on Mexican heritage. Arts and crafts from western, central, and southern Mexico are represented as well as many which are common to all of Mexico. Some of the activities included are weaving, chewing gum sculpture, paper…

A Cross-Cultural Collaboration: Using Visual Culture for the Creation of a Socially Relevant Mural in Mexico

ERIC Educational Resources Information Center

Hubbard, Kathy

2010-01-01

In this article, the author describes how high school and university students in Georgia and members of a small weaving pueblo in Oaxaca, Mexico, collaborated in designing and creating a mural in the central market ("mercado") of the pueblo. A number of lessons emerged from this multi-cultural collaboration. First they learned that using…

Guided by Great Feelings of Love: Using Photovoice and Critical Pedagogy to Document the Life Experiences of Undocumented Latino/a Students in Higher Education

ERIC Educational Resources Information Center

Ortega, Ricardo Elias

2013-01-01

Undocumented students have fought for the ability to attend institutions of higher education, but research has often overlooked their experiences outside of the classroom. Weaving together Freirean critical pedagogy and photovoice to create a type of advocacy participatory action research, this project followed eight undocumented Latina/o…

Build a Band Hands-on Challenge: Investigate Sound with PBS's "Design Squad Nation"[TM

ERIC Educational Resources Information Center

Feinberg, Lauren

2010-01-01

This article describes "Build a Band" hands-on activity from "Design Squad Nation," which allows kids to use simple materials to build a four-stringed instrument, then tune it and play a song. Kids explore frequency, pitch, and sound energy while following the steps of the engineering design process. By weaving "Design Squad Nation" episodes,…

Guidelines for Developing and Inserting Material Properties into the Code 65 Composite Material Database

DTIC Science & Technology

2011-12-01

kind of base fiber used Fab-ric uni, stitched, weave, woven roving, textile form, tape, prepreg Laminate Schedu le [0]10 [0]14 [0]36 Manufacturing...roving, textile form, tape, prepreg Laminate Schedule [0]10 [0]14 [0]36 Manufacturing Date 2006 Test Facility/Date 2007 Program of Record AHM&ST...9 Laminate Schedule .......................................................................................................10 Cure

Brown v. Board of Education: A Civil Rights Milestone and Its Troubled Legacy. Pivotal Moments in American History.

ERIC Educational Resources Information Center

Patterson, James T.

This book presents a narrative version of Brown v. Board of Education of Topeka, Kansas, which struck down state-sponsored racial segregation in America's schools. It analyzes the origins and consequences of that landmark case, illuminating the legal, political, and social implications of this decision. The book weaves many controversial issues…

Growing into the Role: Empowerment of a Music Educator through Application of a Symbolic Interaction Theory

ERIC Educational Resources Information Center

Cox, Patricia J.

2004-01-01

This article presents aspects of professional development, using a narrative case-history approach. It represents the author's own case as an illustration of the kind of integrative experience that may occur as women assume professional careers. In this article, the author weaves the scholarly and theoretical components into the reality of a lived…

Weaving a Virtual Web: Practical Approaches to New Information Technologies.

ERIC Educational Resources Information Center

Gruber, Sibylle, Ed.

With sections on using the Web to plan and structure courses, conduct research, and publish student work, as well as a reference essay that reviews Web sites for educators and students, this book reveals the rich variety of ways in which this technology can be used by English and language arts teachers at all levels. The 20 essays in the book…

Processing and Characterization of Liquid-Phase Sintered NiTi Woven Structures

NASA Astrophysics Data System (ADS)

Erdeniz, Dinc; Weidinger, Ryan P.; Sharp, Keith W.; Dunand, David C.

2018-03-01

Porous NiTi is of interest for bone implants because of its unique combination of biocompatibility (encouraging osseointegration), high strength (to prevent fracture), low stiffness (to reduce stress shielding), and shape memory or superelasticity (to deploy an implant). A promising method for creating NiTi structures with regular open channels is via 3D weaving of NiTi wires. This paper presents a processing method to bond woven NiTi wire structures at contact points between wires to achieve structural integrity: (i) a slurry consisting of a blend of NiTi and Nb powders is deposited on the surface of the NiTi wires after the weaving operation; (ii) the powders are melted to create a eutectic liquid phase which collects at contact points; and (iii) the liquid is solidified and binds the NiTi woven structures. The bonded NiTi wire structures exhibited lower transformation temperatures compared to the as-woven NiTi wires because of Nb diffusion into the NiTi wires. A bonded woven sample was deformed in bending and showed near-complete recovery up to 6% strain and recovered nearly half of the deformation up to 19% strain.

DOE Office of Scientific and Technical Information (OSTI.GOV)

An, Bo; Jenkins, Janelle E; Sampath, Sujatha

Dragline silk from orb-weaving spiders is a copolymer of two large proteins, major ampullate spidroin 1 (MaSp1) and 2 (MaSp2). The ratio of these proteins is known to have a large variation across different species of orb-weaving spiders. NMR results from gland material of two different species of spiders, N. clavipes and A. aurantia, indicates that MaSp1 proteins are more easily formed into β-sheet nanostructures, while MaSp2 proteins form random coil and helical structures. To test if this behavior of natural silk proteins could be reproduced by recombinantly produced spider silk mimic protein, recombinant MaSp1/MaSp2 mixed fibers as well asmore » chimeric silk fibers from MaSp1 and MaSp2 sequences in a single protein were produced based on the variable ratio and conserved motifs of MaSp1 and MaSp2 in native silk fiber. Mechanical properties, solid-state NMR, and XRD results of tested synthetic fibers indicate the differing roles of MaSp1 and MaSp2 in the fiber and verify the importance of postspin stretching treatment in helping the fiber to form the proper spatial structure.« less

Characterization of impact damage in woven fiber composites using fiber Bragg grating sensing and NDE

NASA Astrophysics Data System (ADS)

Hiche, Cristobal; Liu, Kuang C.; Seaver, Mark; Wei, Jun; Chattopadhyay, Aditi

2009-03-01

Woven fiber composites are currently being investigated due to their advantages over other materials, making them suitable for low weight, high stiffness, and high interlaminar fracture toughness applications such as missiles, body armor, satellites, and many other aerospace applications. Damage characterization of woven fabrics is a complex task due to their tendency to exhibit different failure modes based on the weave configuration, orientation, ply stacking and other variables. A multiscale model is necessary to accurately predict progressive damage. The present research is an experimental study on damage characterization of three different woven fiber laminates under low energy impact using Fiber Bragg Grating (FBG) sensors and flash thermography. A correlation between the measured strain from FBG sensors and the damaged area obtained from flash thermography imaging has been developed. It was observed that the peak strain in the fabrics were strongly dependent on the weave geometry and decreased at different rates as damage area increased due to dissimilar failure modes. Experimental observations were validated with the development of a multiscale model. A FBG sensor placement model was developed which showed that FBG sensor location and orientation plays a key role in the sensing capabilities of strain on the samples.

Phase field simulations of autocatalytic formation of alpha lamellar colonies in Ti-6Al-4V

DOE PAGES

Radhakrishnan, Bala; Gorti, Sarma; Babu, Suresh Sudharsanam

2016-09-13

Here, we present phase field simulations incorporating energy contributions due to thermodynamics, and anisotropic interfacial and strain energies, to demonstrate the nucleation and growth of multiple variants of alpha from beta in Ti-6Al-4V under isothermal conditions. The simulations focused on the effect of thermodynamic driving force and nucleation rate on the morphology of the transformed alpha assuming that the partitioning of V between beta and alpha is negligible for short isothermal holds. The results indicate that a high nucleation rate favors the formation of the basket-weave structure. However, at a lower nucleation rate the simulations show the intragranular nucleation ofmore » a colony structure by an autocatalytic nucleation mechanism adjacent to a pre-existing alpha variant. New side-plates of the same variant appear to nucleate progressively and grow to form the colony. The isothermal simulation results are used to offer a possible explanation for the transition from a largely basket weave structure to a colony structure inside narrow layer bands occurring during continuous heating and cooling conditions encountered during laser additive manufacturing of Ti-6Al-4V.« less

Urbanisation at multiple scales is associated with larger size and higher fecundity of an orb-weaving spider.

PubMed

Lowe, Elizabeth C; Wilder, Shawn M; Hochuli, Dieter F

2014-01-01

Urbanisation modifies landscapes at multiple scales, impacting the local climate and changing the extent and quality of natural habitats. These habitat modifications significantly alter species distributions and can result in increased abundance of select species which are able to exploit novel ecosystems. We examined the effect of urbanisation at local and landscape scales on the body size, lipid reserves and ovary weight of Nephila plumipes, an orb weaving spider commonly found in both urban and natural landscapes. Habitat variables at landscape, local and microhabitat scales were integrated to create a series of indexes that quantified the degree of urbanisation at each site. Spider size was negatively associated with vegetation cover at a landscape scale, and positively associated with hard surfaces and anthropogenic disturbance on a local and microhabitat scale. Ovary weight increased in higher socioeconomic areas and was positively associated with hard surfaces and leaf litter at a local scale. The larger size and increased reproductive capacity of N.plumipes in urban areas show that some species benefit from the habitat changes associated with urbanisation. Our results also highlight the importance of incorporating environmental variables from multiple scales when quantifying species responses to landscape modification.

Urbanisation at Multiple Scales Is Associated with Larger Size and Higher Fecundity of an Orb-Weaving Spider

PubMed Central

Lowe, Elizabeth C.; Wilder, Shawn M.; Hochuli, Dieter F.

2014-01-01

Urbanisation modifies landscapes at multiple scales, impacting the local climate and changing the extent and quality of natural habitats. These habitat modifications significantly alter species distributions and can result in increased abundance of select species which are able to exploit novel ecosystems. We examined the effect of urbanisation at local and landscape scales on the body size, lipid reserves and ovary weight of Nephila plumipes, an orb weaving spider commonly found in both urban and natural landscapes. Habitat variables at landscape, local and microhabitat scales were integrated to create a series of indexes that quantified the degree of urbanisation at each site. Spider size was negatively associated with vegetation cover at a landscape scale, and positively associated with hard surfaces and anthropogenic disturbance on a local and microhabitat scale. Ovary weight increased in higher socioeconomic areas and was positively associated with hard surfaces and leaf litter at a local scale. The larger size and increased reproductive capacity of N.plumipes in urban areas show that some species benefit from the habitat changes associated with urbanisation. Our results also highlight the importance of incorporating environmental variables from multiple scales when quantifying species responses to landscape modification. PMID:25140809

Modeling the Nonlinear, Strain Rate Dependent Deformation of Woven Ceramic Matrix Composites With Hydrostatic Stress Effects Included

NASA Technical Reports Server (NTRS)

Goldberg, Robert K.; Carney, Kelly S.

2004-01-01

An analysis method based on a deformation (as opposed to damage) approach has been developed to model the strain rate dependent, nonlinear deformation of woven ceramic matrix composites with a plain weave fiber architecture. In the developed model, the differences in the tension and compression response have also been considered. State variable based viscoplastic equations originally developed for metals have been modified to analyze the ceramic matrix composites. To account for the tension/compression asymmetry in the material, the effective stress and effective inelastic strain definitions have been modified. The equations have also been modified to account for the fact that in an orthotropic composite the in-plane shear stiffness is independent of the stiffness in the normal directions. The developed equations have been implemented into a commercially available transient dynamic finite element code, LS-DYNA, through the use of user defined subroutines (UMATs). The tensile, compressive, and shear deformation of a representative plain weave woven ceramic matrix composite are computed and compared to experimental results. The computed values correlate well to the experimental data, demonstrating the ability of the model to accurately compute the deformation response of woven ceramic matrix composites.

Rowing the Weaves of Community Participation: Good Practices in Early Childhood Development (ECD) Program in Rural Central Lombok, West Nusa Tenggara

ERIC Educational Resources Information Center

Abdillah, Ali

2014-01-01

This paper describes the rural community participation within the context of an integrated early childhood development program initiated by the government of Indonesia in partnership with UNICEF and AusAID in Central Lombok (2008-2010). Based on purposive interviews with relevant stakeholders, as well as an analysis of past documents, researchers'…

Weaving Intergenerational Engagement into ESL Instruction: Case Study of a University-Based Program in Hong Kong

ERIC Educational Resources Information Center

Lai, Alan; Kaplan, Matthew

2016-01-01

This article aims to address the practical question of whether there is educational value to embedding second-language (L2) learning experiences in intergenerational contexts. In particular, a case study was conducted of a novel, university-based ESL program in Hong Kong in which a group of older adult volunteers with a high level of English…

Advanced Survivable Radiator Development Program

DTIC Science & Technology

1993-03-01

pyrolytic process. The ceramic fiber is amorphous with a typical elemental composition of 57% silicon, 28% nitrogen, 10% carbon , and 4% oxygen, and has an...exist: Optimum choice dependent on mission, operational requirements, and threat environment Configurations: Fibers , Rods, Fins Carbon - Carbon e ASpecial... Carbon Fiber Area Density ,,,--Stainless Aluminum Be Diamond BC Bond Copper Weave: Be, Al, SS. Ti, Nitinol Configurations: Low Z or High Z. depending

Weaving Webs of Intrigue: Classical Mythology and Analytic Crime Fiction in Rubem Fonseca's "A grande arte"

ERIC Educational Resources Information Center

Ginway, M. Elizabeth

2013-01-01

This study focuses on some of the classical features of Rubem Fonseca's "A grande arte" (1983) in order to emphasize the puzzle-solving tradition of the detective novel that is embedded within Fonseca's crime thriller, producing a work that does not entirely fit into traditional divisions of detective, hardboiled, or crime…

Virtual Prototyping for Personal Protective Equipment and Workplaces

DTIC Science & Technology

1999-03-01

Basket Weave Kevlar-29 Fabric Loosely Draped over 20% Ordnance Gelatin Block Subject to Non-Perforating Impact by .38 Special (130-grain FMJ...Fabric and fabric-like materials are very difficult to model because of the dynamic properties of folding, draping , and stretching. How these...Targets Bare Targets with Insitu Instrumentation V7 Instrumented Targets with Loosely Draped Clothing SL Instrumented Targets with Body Armor

"Ka ulana 'ana i ka piko" (In Weaving You Begin at the Center): Perspectives from a Culturally Specific Approach to Art Education

ERIC Educational Resources Information Center

Dewhurst, Marit; Keawe, Lia O'Neill Moanike'Ala Ah-Lan; MacDowell, Marsha; Okada-Carlson, Cherie N. K.; Wong, Annette Ku'Uipolani

2013-01-01

This essay examines the experiences of "lau hala" ("pandanus" leaf plaiting) weavers for the pedagogical philosophies and strategies embedded in this Hawaiian art form in an effort to broaden the ways in which we understand and practice art education in any setting. Drawing on personal experiences as "lau hala"…

Towards a Pedagogy of the Incomprehensible: Trauma and the Imperative of Critical Witness in Literacy Classrooms

ERIC Educational Resources Information Center

Dutro, Elizabeth

2013-01-01

In this article, I explore questions about what it means to carry, live and invite traumatic stories into the space of a literacy classroom. Weaving illustrative moments from the classroom with trauma theory and research, I ask, What does it mean to embrace the incomprehensible in literacy classrooms? How might the incomprehensible be viewed as a…

2. DETAIL VIEW OF MAIN ELEVATION OF MILL, LOOKING NORTHWEST. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. DETAIL VIEW OF MAIN ELEVATION OF MILL, LOOKING NORTHWEST. NOTE ORIGINAL WINDOWS ON UPPER FLOORS. THE TOP FLOOR CONTAINED SPINNING AND TWISTER EQUIPMENT, THE SECOND FLOOR THE CARD ROOM AND ADDITIONAL SPINNING, AND THE GROUND FLOOR WEAVING, THE CLOTH ROOM, AND SHIPPING. A PARTIAL BASEMENT CONTAINED A MACHINE SHOP, SUPPLY DEPARTMENT, AND OVERFLOW COTTON STORAGE. - Stark Mill, 117 Corinth Road, Hogansville, Troup County, GA

1. VIEW OF SOUTHEAST ELEVATION OF GRANITEVILLE MILL COMPLEX. THIS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW OF SOUTHEAST ELEVATION OF GRANITEVILLE MILL COMPLEX. THIS ONE-STORY BRICK SECTION OF THE MILL WAS BUILT AS A WEAVE ROOM ADDITION IN THE 1860s. THE ORIGINAL MONITOR ROOF HAS BEEN REMOVED, AND THE WINDOWS BRICKED-IN. NOTE ONE OF THE TOWER CUPOLAS OF THE ORIGINAL 1846-48 MILL IN THE RIGHT BACKGROUND. - Graniteville Mill, Marshall Street, Graniteville, Aiken County, SC

Cowboys Count, Monkeys Measure, and Princesses Problem Solve: Building Early Math Skills through Storybooks

ERIC Educational Resources Information Center

Wilburne, Jane M.; Keat, Jane B.; Napoli, Mary P.

2011-01-01

Nervous about teaching math to young children? Too pressed for time to teach all of the math concepts children need to know? Now there's a practical, stress-free guide to one of the most effective ways to enhance children's mathematical thinking in pre-K-Grade 3--by weaving math concepts into storytime. Ready for any educator to pick up and start…

Women of Mexico: The Consecrated and the Commoners, 1519-1900. La Mujer Latina Series.

ERIC Educational Resources Information Center

Gugliotta, Bobette

This collective biography offers insight into the more famous and infamous women in Mexico's history and weaves the tale of how their ways and deeds have shaped both a culture and a nation. The book starts with the conquest and ends with the twentieth century, outlining the lives of Mexican women and their causes. The women described in the book…

FILTER FOR HIGH VELOCITY GAS STREAMS

DOEpatents

Heckman, R.A.; Warner, H.F.

1963-11-01

An air filter that is particularly useful in air-sampling rockets is presented. The filter comprises a cellulose fiber mat having an evenly disposed thin coating of stearic acid. Protective loose weave fabric covers are stitched to the front and back of the fiber mat, the stitching being in the form of a sine wave spiraled from the midpoint of the mat out to its periphery. (AEC)

Weaving Whole Cloth: The Nurture of a Highly Intelligent Child. What Is It Like To Live with a Highly Intelligent Child?

ERIC Educational Resources Information Center

Sargeant, Hope

2000-01-01

The parent of an extremely intelligent child discusses what it is like to live with a child who exhibits a different web of cognition, perception, intuition, and mental processing; the necessity of educational acceleration for learning to achieve and develop self-esteem; and the importance of challenging material in learning the satisfaction of…

Weaving a Fabric of World History? An Analysis of U.S. State High School World History Standards

ERIC Educational Resources Information Center

Marino, Michael; Bolgatz, Jane

2010-01-01

Understanding world history is critical for our development as citizens in our interconnected society. Yet it is not clear that the standards for world history courses in the U.S. foster understanding of the whole world or of its history. The authors argue that the high school world history standards mapped out by various states promulgate a…

A Tapestry of Inquiry and Action: Cycle of Learning Weaves Its Way through Washington District

ERIC Educational Resources Information Center

Rasmussen, Harriette Thurber; Karschney, Kathryn

2012-01-01

Welcome to the West Valley School District in eastern Washington. Home to almost 4,000 students, West Valley made a public commitment more than seven years ago that all students would graduate with the option to attend college. This daunting goal--made even more so by the fact that almost half of the district's high school students come from…

The European Universities, Citizenship and Its Limits: What Won't Solve the Problems of Our Time

ERIC Educational Resources Information Center

Lock, Grahame; Martins, Herminio

2009-01-01

This article attempts to weave together in an original manner a number of themes regarding citizenship and higher education in Europe. Thus, the authors look critically at the notion of citizenship itself; its role in Aristotle and in Hegel's state-versus-civil-society contrast; its relation to the world of work or labour; its connection with the…