40 CFR 63.3370 - How do I demonstrate compliance with the emission standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

... equivalent allowable organic HAP (Equation 13a or b of § 63.3370). (4) Use of a capture system and control... control devices (i) Average equivalent organic HAP emission rate does not exceed 0.2 kg organic HAP per kg... material applied on the web coating line or group of web coating lines controlled by a common control...

40 CFR 63.3290 - Does this subpart apply to me?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Hazardous Air Pollutants: Paper and Other Web Coating What This Subpart Covers § 63.3290 Does... is a major source of HAP, as defined in § 63.2, at which web coating lines are operated. ...

40 CFR 63.3290 - Does this subpart apply to me?

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating What This Subpart... existing facility that is a major source of HAP, as defined in § 63.2, at which web coating lines are...

40 CFR 63.3290 - Does this subpart apply to me?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants: Paper and Other Web Coating What This Subpart Covers § 63.3290 Does... is a major source of HAP, as defined in § 63.2, at which web coating lines are operated. ...

The Environmental Assessment and Management (TEAM) Guide: New York Supplement

DTIC Science & Technology

2010-03-01

pressure-sensitive tape regardless of substance (including paper , fabric or plastic film) and related web coating processes on plastic film such as...Cartridge Filter - a replaceable cartridge filter that contains one of the following as the filter medium: paper , activated carbon, or paper and activated...associated drying or curing areas. A single coating line ends after drying or curing and before other surface coatings are applied. For any web

40 CFR 60.441 - Definitions and symbols.

Code of Federal Regulations, 2010 CFR

2010-07-01

... web. Coating line means any number or combination of adhesive, release, or precoat coating applicators... solids content of the coated adhesive, release, or precoat as measured by Method 24. Flashoff area means... than an adhesive or release is applied to a surface during the production of a pressure sensitive tape...

The Environmental Assessment and Management (TEAM) Guide: West Virginia Supplement

DTIC Science & Technology

2010-01-01

WVCSR 45-21-19) [Citation Revised January 2008]. • Paper Coating Line - a web coating line where coating is applied to paper . Printing presses are...from a ny stack, pi pe, a ir pol lution c ontrol de vice, or f rom a ny ot her equipment or facilities associated with a c hemical processing unit...to, hoods, ducts, fans, booths, ovens, dryers , e tc.) that contains, collects, and transports an air pollutant to a control device (WVCSR 45-21-2.9

40 CFR 63.5110 - What special definitions are used in this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... equipment used to apply an organic coating to the surface of metal coil. A coil coating line includes a web... emission limitation (including any operating limit) or work practice standard; (2) Fails to meet any term... before July 18, 2000, and it has not subsequently undergone reconstruction as defined in § 63.2. Facility...

Solar cells and modules from dentritic web silicon

NASA Technical Reports Server (NTRS)

Campbell, R. B.; Rohatgi, A.; Seman, E. J.; Davis, J. R.; Rai-Choudhury, P.; Gallagher, B. D.

1980-01-01

Some of the noteworthy features of the processes developed in the fabrication of solar cell modules are the handling of long lengths of web, the use of cost effective dip coating of photoresist and antireflection coatings, selective electroplating of the grid pattern and ultrasonic bonding of the cell interconnect. Data on the cells is obtained by means of dark I-V analysis and deep level transient spectroscopy. A histogram of over 100 dentritic web solar cells fabricated in a number of runs using different web crystals shows an average efficiency of over 13%, with some efficiencies running above 15%. Lower cell efficiency is generally associated with low minority carrier time due to recombination centers sometimes present in the bulk silicon. A cost analysis of the process sequence using a 25 MW production line indicates a selling price of $0.75/peak watt in 1986. It is concluded that the efficiency of dentritic web cells approaches that of float zone silicon cells, reduced somewhat by the lower bulk lifetime of the former.

40 CFR 63.4321 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... compliant material option for any individual web coating/printing operation, for any group of web coating/printing operations in the affected source, or for all the web coating/printing operations in the affected... HAP concentration option for any web coating/printing operation(s) in the affected source for which...

40 CFR 63.4321 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... compliant material option for any individual web coating/printing operation, for any group of web coating/printing operations in the affected source, or for all the web coating/printing operations in the affected... HAP concentration option for any web coating/printing operation(s) in the affected source for which...

40 CFR 63.4331 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2011 CFR

2011-07-01

... web coating/printing operations, you may use the emission rate without add-on controls option for any individual web coating/printing operation, for any group of web coating/printing operations in the affected source, or for all the web coating/printing operations as a group in the affected source. You must use...

40 CFR 63.4331 - How do I demonstrate initial compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... web coating/printing operations, you may use the emission rate without add-on controls option for any individual web coating/printing operation, for any group of web coating/printing operations in the affected source, or for all the web coating/printing operations as a group in the affected source. You must use...

40 CFR 63.3370 - How do I demonstrate compliance with the emission standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating... material, i, in a month, kg. Mvret = Mass of volatile matter retained in the coated web after curing or...-purchased coating material, i, in a month, kg. Mvret = Mass of volatile matter retained in the coated web...

40 CFR 63.3370 - How do I demonstrate compliance with the emission standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

... or group of web coating lines controlled by a common control device during the month. (vi) If... monthly HAP applied (Equation 6 of § 63.3370) is less than the calculated equivalent allowable organic HAP (Equation 13a or b of § 63.3370). (4) Use of a capture system and control device (i) Overall organic HAP...

Thin film-coated polymer webs

DOEpatents

Wenz, Robert P.; Weber, Michael F.; Arudi, Ravindra L.

1992-02-04

The present invention relates to thin film-coated polymer webs, and more particularly to thin film electronic devices supported upon a polymer web, wherein the polymer web is treated with a purifying amount of electron beam radiation.

40 CFR 63.4292 - What operating limits must I meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Limitations § 63.4292 What operating limits must I meet? (a) For any web coating/printing operation, slashing operation, or dyeing/finishing operation on which you use the compliant material option; web coating..., you are not required to meet any operating limits. (b) For any controlled web coating/printing...

40 CFR 63.4291 - What are my options for meeting the emission limits?

Code of Federal Regulations, 2010 CFR

2010-07-01

... emission capture systems and add-on controls, the organic HAP emission rate for the web coating/printing... demonstrate that all capture systems and control devices for the web coating/printing operation(s) meet the... capture systems and control devices for the web coating/printing operation(s) meet the operating limits...

40 CFR 63.4292 - What operating limits must I meet?

Code of Federal Regulations, 2010 CFR

2010-07-01

... systems on the web coating/printing operation(s) and dyeing/finishing operations for which you use this... Limitations § 63.4292 What operating limits must I meet? (a) For any web coating/printing operation, slashing operation, or dyeing/finishing operation on which you use the compliant material option; web coating...

40 CFR 63.4351 - How do I demonstrate initial compliance?

Code of Federal Regulations, 2011 CFR

2011-07-01

... period. The device must be initially certified by the manufacturer to be accurate to within ±2.0 percent... to paragraph (d)(2) of this section. q = Number of controlled web coating/printing operations except... option for any individual web coating/printing operation, for any group of web coating/printing...

40 CFR 63.4351 - How do I demonstrate initial compliance?

Code of Federal Regulations, 2010 CFR

2010-07-01

... period. The device must be initially certified by the manufacturer to be accurate to within ±2.0 percent... to paragraph (d)(2) of this section. q = Number of controlled web coating/printing operations except... option for any individual web coating/printing operation, for any group of web coating/printing...

40 CFR 63.4292 - What operating limits must I meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Other Textiles Emission Limitations § 63.4292 What operating limits must I meet? (a) For any web coating... material option; web coating/printing operation or dyeing/finishing operation on which you use the emission... controlled web coating/printing operation or dyeing/finishing operation on which you use the emission rate...

40 CFR 63.4292 - What operating limits must I meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Other Textiles Emission Limitations § 63.4292 What operating limits must I meet? (a) For any web coating... material option; web coating/printing operation or dyeing/finishing operation on which you use the emission... controlled web coating/printing operation or dyeing/finishing operation on which you use the emission rate...

40 CFR 63.4292 - What operating limits must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Other Textiles Emission Limitations § 63.4292 What operating limits must I meet? (a) For any web coating... material option; web coating/printing operation or dyeing/finishing operation on which you use the emission... controlled web coating/printing operation or dyeing/finishing operation on which you use the emission rate...

Effect of Elasticity on Stability of Viscoelastic Liquid Curtain

NASA Astrophysics Data System (ADS)

Mohammad Karim, Alireza; Suszynski, Wieslaw; Francis, Lorraine; Carvalho, Marcio; University of Minnesota, Twin Cities Collaboration; Pontifícia Universidade Católica do Rio de Janeiro Collaboration; Dow Chemical Company Collaboration

2016-11-01

Curtain coating is one the preferred methods for high-speed precision application of single-layer and multi-layer coatings in industry. Despite the extensive variety of applications of curtain coating, its operation is challenging and uniform coating is only obtained in a certain range of operating parameters, called the coating window. The two main physical mechanisms that limit curtain coating are the breakup of the liquid curtain, below a critical flow rate, and the catastrophic event of air entrainment, which occurs above a certain web speed. The rheological characteristics of the coating liquid play an important role on these mechanisms, but the fundamental understanding of the role of rheology is still not complete. In this work, we analyze the relative importance of shear and extensional viscosity on both curtain breakup and dynamic contact line instability (i.e. air entrainment). Aqueous solutions of polyethylene oxide (PEO) and polyethylene glycol (PEG) of different molecular weights were used as model liquids to obtain fluids with different levels of extensional thickening behavior. We would like to acknowledge the financial support from the Dow Chemical Company.

75 FR 8807 - Delegation of National Emission Standards for Hazardous Air Pollutants for Source Categories...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-26

.... JJJJ Paper and Other Web X X X Coating. KKKK Surface Coating of X X X Metal Cans. MMMM Miscellaneous... X X Facilities. S Pulp and Paper X T Halogenated Solvent Cleaning.. X X U Group I Polymers and... Automobiles X and Light-Duty Trucks. JJJJ Paper and Other Web Coating... X KKKK Surface Coating of Metal Cans...

40 CFR 60.741 - Definitions, symbols, and cross-reference tables.

Code of Federal Regulations, 2010 CFR

2010-07-01

... prepolymers to a supporting web other than paper, plastic film, metallic foil, or metal coil. Substrate means... (i) entering the emission control device, in dry standard cubic meters per hour when Method 18 or 25... coats a continuous web to produce a substrate with a polymeric coating. Should the coating process not...

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2013 CFR

2013-07-01

... part 51 to determine the mass fraction of TVH liquid input from each regulated material used in the web.... TVHi = Mass fraction of TVH in regulated material, i, that is applied in the web coating/printing or... the mass of liquid TVH in regulated materials applied in the web coating/printing or dyeing/finishing...

77 FR 37905 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-25

... Activities; Submission to OMB for Review and Approval; Comment Request; NESHAP for Paper and Other Web... electronic docket, go to www.regulations.gov . Title: NESHAP for Paper and Other Web Coating (Renewal). ICR... and Other Web Coating is subject to the General Provisions of the NESHAP at 40 CFR part 63, subpart A...

Compliance Options Diagrams for the Paper and Other Web Coating National Emission Standards for Hazardous Air Pollutants (NESHAP)

EPA Pesticide Factsheets

This January 2004 document contains 14 diagrams illustrating the different compliance options available for those facilities that fall under the Paper and Web Coating Maximum Achievable control Technology (MACT).

The Barrier Properties of PET Coated DLC Film Deposited by Microwave Surface-Wave PECVD

NASA Astrophysics Data System (ADS)

Yin, Lianhua; Chen, Qiang

2017-12-01

In this paper we report the investigation of diamond-like carbon (DLC) deposited by microwave surface-wave plasma enhanced chemical vapor deposition (PECVD) on the polyethylene terephthalate (PET) web for the purpose of the barrier property improvement. In order to characterize the properties of DLC coatings, we used several substrates, silicon wafer, glass, and PET web and KBr tablet. The deposition rate was obtained by surface profiler based on the DLC deposited on glass substrates; Fourier transform infrared spectroscope (FTIR) was carried out on KBr tablets to investigate chemical composition and bonding structure; the morphology of the DLC coating was analyzed by atomic force microscope (AFM) on Si substrates. For the barrier properties of PET webs, we measured the oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) after coated with DLC films. We addressed the film barrier property related to process parameters, such as microwave power and pulse parameter in this work. The results show that the DLC coatings can greatly improve the barrier properties of PET webs.

Paper and Other Web Coating: National Emission Standards for Hazardous Air Pollutants (NESHAP)

EPA Pesticide Factsheets

Find information on the NESHAP for paper and other web coatings. Read the rule summary, history and supporting documents including fact sheets, responses to public comments, related rules, and compliance and applicability information for this regulation.

Paper and Other Web Coating National Emission Standards for Hazardous Air Pollutants (NESHAP) Questions and Answers

EPA Pesticide Factsheets

This May 2003 document contains questions and answers on the Paper and Web Coating National Emission Standards for Hazardous Air Pollutants (NESHAP) regulation. The questions cover topics such as compliance, applicability, and initial notification.

Atmospheric pressure spatial atomic layer deposition web coating with in situ monitoring of film thickness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yersak, Alexander S.; Lee, Yung C.; Spencer, Joseph A.

Spectral reflectometry was implemented as a method for in situ thickness monitoring in a spatial atomic layer deposition (ALD) system. Al{sub 2}O{sub 3} films were grown on a moving polymer web substrate at 100 °C using an atmospheric pressure ALD web coating system, with film growth of 0.11–0.13 nm/cycle. The modular coating head design and the in situ monitoring allowed for the characterization and optimization of the trimethylaluminum and water precursor exposures, purge flows, and web speed. A thickness uniformity of ±2% was achieved across the web. ALD cycle times as low as 76 ms were demonstrated with a web speed of 1 m/smore » and a vertical gap height of 0.5 mm. This atmospheric pressure ALD system with in situ process control demonstrates the feasibility of low-cost, high throughput roll-to-roll ALD.« less

Infrared-thermography imaging system multiapplications for manufacturing

NASA Astrophysics Data System (ADS)

Stern, Sharon A.

1990-03-01

Imaging systems technology has been utilized traditionally for diagnosing structural envelope or insulation problems in the general thermographic comunity. Industrially, new applications for utilizing thermal imaging technology have been developed i n pred i cti ve/preventi ye mai ntenance and prod uct moni tori ng prociures at Eastman Kodak Company, the largest photographic manufacturering producer in the world. In the manufacturing processes used at Eastman Kodak Company, new applications for thermal imaging include: (1) Fluid transfer line insulation (2) Web coating drying uniformity (3) Web slitter knives (4) Heating/cooling coils (5) Overheated tail bearings, and (6) Electrical phase imbalance. The substantial cost benefits gained from these applications of infrared thermography substantiate the practicality of this approach and indicate the desirability of researching further appl i cati ons.

40 CFR 60.740 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... fraction; (3) Web coating operations that print an image on the surface of the substrate or any coating... coating operation and any onsite coating mix preparation equipment used to prepare coatings for the... coatings at one plant for shipment to another plant for use in an affected facility (coating operation) or...

EVALUATION OF BARRIERS TO THE USE OF RADIATION CURED COATINGS IN WIDE-WEB FLEXOGRAPHIC PRINTING

EPA Science Inventory

The report gives results of a study to investigate and identify the technical, economic, and educational barriers to the use and implementation of radiation-curable coatings (primarily ultraviolet (UV) curable inks) in the wide-web flexographic printing industry. (NOTE: In suppor...

Paper and Other Web Coating Maximum Achievable Control Technology (MACT): Work Practice, Testing, Monitoring, Recordkeeping, and Reporting Summary Table

EPA Pesticide Factsheets

This April 2004 document is a table that details the various requirements of the Paper and Other Web Coating NESHAP, broken down by category. This table covers applicability, recordkeeping, emission limits, work practice standards, and other requirements

Development of Ultraviolet (UV) Radiation Protective Fabric Using Combined Electrospinning and Electrospraying Technique

NASA Astrophysics Data System (ADS)

Sinha, Mukesh Kumar; Das, B. R.; Kumar, Kamal; Kishore, Brij; Prasad, N. Eswara

2017-06-01

The article reports a novel technique for functionization of nanoweb to develop ultraviolet (UV) radiation protective fabric. UV radiation protection effect is produced by combination of electrospinning and electrospraying technique. A nanofibrous web of polyvinylidene difluoride (PVDF) coated on polypropylene nonwoven fabric is produced by latest nanospider technology. Subsequently, web is functionalized by titanium dioxide (TiO2). The developed web is characterized for evaluation of surface morphology and other functional properties; mechanical, chemical, crystalline and thermal. An optimal (judicious) nanofibre spinning condition is achieved and established. The produced web is uniformly coated by defect free functional nanofibres in a continuous form of useable textile structural membrane for ultraviolet (UV) protective clothing. This research initiative succeeds in preparation and optimization of various nanowebs for UV protection. Field Emission Scanning Electron Microscope (FESEM) result reveals that PVDF webs photo-degradative behavior is non-accelerated, as compared to normal polymeric grade fibres. Functionalization with TiO2 has enhanced the photo-stability of webs. The ultraviolet protection factor of functionalized and non-functionalized nanowebs empirically evaluated to be 65 and 24 respectively. The developed coated layer could be exploited for developing various defence, para-military and civilian UV protective light weight clothing (tent, covers and shelter segments, combat suit, snow bound camouflaging nets). This research therefore, is conducted in an attempt to develop a scientific understanding of PVDF fibre coated webs for photo-degradation and applications for defence protective textiles. This technological research in laboratory scale could be translated into bulk productionization.

Compliance Timeline and Applicability Determination for Paper and Other Web Coating National Emission Standards for Hazardous Air Pollutants (NESHAP)

EPA Pesticide Factsheets

This February 2003 document contains a diagram of dates and events for compliance with the NESHAP for Paper and Other Web Coating. Also on this page is an April 2004 flow chart to determine if the NESHAP applies to your facility.

Fact Sheet and Executive Summary for the National Emission Standards of Hazardous Air Pollutants (NESHAP) for Paper and Other Web Coating

EPA Pesticide Factsheets

This page contains the August 2002 final rule fact sheet on the NESHAP for Paper and Other Web Coating. Also on this page is an April 2004 presentation that on the NESHAP, designed to be used for basic education

40 CFR 63.4352 - How do I demonstrate continuous compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., shutdown, or malfunction of the emission capture system, add-on control device, or web coating/printing... specified in Table 2 to this subpart, then you must assume that the emission capture system and add-on..., thinning, and cleaning materials applied during a deviation on a controlled web coating/printing operation...

The role of capture spiral silk properties in the diversification of orb webs.

PubMed

Tarakanova, Anna; Buehler, Markus J

2012-12-07

Among a myriad of spider web geometries, the orb web presents a fascinating, exquisite example in architecture and evolution. Orb webs can be divided into two categories according to the capture silk used in construction: cribellate orb webs (composed of pseudoflagelliform silk) coated with dry cribellate threads and ecribellate orb webs (composed of flagelliform silk fibres) coated by adhesive glue droplets. Cribellate capture silk is generally stronger but less-extensible than viscid capture silk, and a body of phylogenic evidence suggests that cribellate capture silk is more closely related to the ancestral form of capture spiral silk. Here, we use a coarse-grained web model to investigate how the mechanical properties of spiral capture silk affect the behaviour of the whole web, illustrating that more elastic capture spiral silk yields a decrease in web system energy absorption, suggesting that the function of the capture spiral shifted from prey capture to other structural roles. Additionally, we observe that in webs with more extensible capture silk, the effect of thread strength on web performance is reduced, indicating that thread elasticity is a dominant driving factor in web diversification.

The role of capture spiral silk properties in the diversification of orb webs

PubMed Central

Tarakanova, Anna; Buehler, Markus J.

2012-01-01

Among a myriad of spider web geometries, the orb web presents a fascinating, exquisite example in architecture and evolution. Orb webs can be divided into two categories according to the capture silk used in construction: cribellate orb webs (composed of pseudoflagelliform silk) coated with dry cribellate threads and ecribellate orb webs (composed of flagelliform silk fibres) coated by adhesive glue droplets. Cribellate capture silk is generally stronger but less-extensible than viscid capture silk, and a body of phylogenic evidence suggests that cribellate capture silk is more closely related to the ancestral form of capture spiral silk. Here, we use a coarse-grained web model to investigate how the mechanical properties of spiral capture silk affect the behaviour of the whole web, illustrating that more elastic capture spiral silk yields a decrease in web system energy absorption, suggesting that the function of the capture spiral shifted from prey capture to other structural roles. Additionally, we observe that in webs with more extensible capture silk, the effect of thread strength on web performance is reduced, indicating that thread elasticity is a dominant driving factor in web diversification. PMID:22896566

The Environmental Assessment and Management (TEAM) Guide: Iowa Supplement

DTIC Science & Technology

2010-02-01

limited to, paper shredding, copying, photographic activities, and blueprinting machines. This does not include incinerators. r. Laundry dryers ...exemptions from these standards may apply. (Part 63, Subpart IIII) cj. Emission standards for hazardous air pollutants: paper and other web ...coating. This standard applies to a facility that is engaged in the coating of paper , plastic film, metallic foil, and other web surfaces located at a

Coatings Boost Solar-Cell Outputs

NASA Technical Reports Server (NTRS)

Rohatgi, Ajeet; Campbell, Robert B.; O'Keefe, T. W.; Rai-Choudbury, Posenjit; Hoffman, Richard A.

1988-01-01

Efficiencies increased by more-complete utilization of incident light. Electrical outputs of thin solar photovoltaic cells made of dendritic-web silicon increased by combination of front-surface, antireflective coatings and back-surface, reflective coatings. Improvements achieved recently through theoretical and experimental studies of ways to optimize coatings for particular wavelengths of incident light, cell thicknesses, and cell materials.

In-Line Monitoring of a Pharmaceutical Pan Coating Process by Optical Coherence Tomography.

PubMed

Markl, Daniel; Hannesschläger, Günther; Sacher, Stephan; Leitner, Michael; Buchsbaum, Andreas; Pescod, Russel; Baele, Thomas; Khinast, Johannes G

2015-08-01

This work demonstrates a new in-line measurement technique for monitoring the coating growth of randomly moving tablets in a pan coating process. In-line quality control is performed by an optical coherence tomography (OCT) sensor allowing nondestructive and contact-free acquisition of cross-section images of film coatings in real time. The coating thickness can be determined directly from these OCT images and no chemometric calibration models are required for quantification. Coating thickness measurements are extracted from the images by a fully automated algorithm. Results of the in-line measurements are validated using off-line OCT images, thickness calculations from tablet dimension measurements, and weight gain measurements. Validation measurements are performed on sample tablets periodically removed from the process during production. Reproducibility of the results is demonstrated by three batches produced under the same process conditions. OCT enables a multiple direct measurement of the coating thickness on individual tablets rather than providing the average coating thickness of a large number of tablets. This gives substantially more information about the coating quality, that is, intra- and intertablet coating variability, than standard quality control methods. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

In-line monitoring of pellet coating thickness growth by means of visual imaging.

PubMed

Oman Kadunc, Nika; Sibanc, Rok; Dreu, Rok; Likar, Boštjan; Tomaževič, Dejan

2014-08-15

Coating thickness is the most important attribute of coated pharmaceutical pellets as it directly affects release profiles and stability of the drug. Quality control of the coating process of pharmaceutical pellets is thus of utmost importance for assuring the desired end product characteristics. A visual imaging technique is presented and examined as a process analytic technology (PAT) tool for noninvasive continuous in-line and real time monitoring of coating thickness of pharmaceutical pellets during the coating process. Images of pellets were acquired during the coating process through an observation window of a Wurster coating apparatus. Image analysis methods were developed for fast and accurate determination of pellets' coating thickness during a coating process. The accuracy of the results for pellet coating thickness growth obtained in real time was evaluated through comparison with an off-line reference method and a good agreement was found. Information about the inter-pellet coating uniformity was gained from further statistical analysis of the measured pellet size distributions. Accuracy and performance analysis of the proposed method showed that visual imaging is feasible as a PAT tool for in-line and real time monitoring of the coating process of pharmaceutical pellets. Copyright © 2014 Elsevier B.V. All rights reserved.

Material-Process-Performance Relationships for Roll-to-Roll Coated PEM Electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauger, Scott; Neyerlin, K.C.; Stickel, Jonathan

2017-04-26

Roll-to-roll (R2R) coating is the most economical and highest throughput method for producing fuel cell electrodes. R2R coating encompasses many different methodologies to create uniform films on a moving web substrate. Here we explore two coating methods, gravure and slot die, to understand the impacts of each on film uniformity and performance.

40 CFR 63.825 - Standards: Product and packaging rotogravure and wide-web flexographic printing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... inks, coatings, varnishes, adhesives, primers, solvents, reducers, thinners, and other materials... calculated equivalent allowable mass based on the organic HAP and solids contents of the inks, coatings... (b)(1) through (b)(10) of this section: (1) Demonstrate that each ink, coating, varnish, adhesive...

40 CFR 63.825 - Standards: Product and packaging rotogravure and wide-web flexographic printing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... inks, coatings, varnishes, adhesives, primers, solvents, reducers, thinners, and other materials... calculated equivalent allowable mass based on the organic HAP and solids contents of the inks, coatings... (b)(1) through (b)(10) of this section: (1) Demonstrate that each ink, coating, varnish, adhesive...

40 CFR 63.825 - Standards: Product and packaging rotogravure and wide-web flexographic printing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... inks, coatings, varnishes, adhesives, primers, solvents, reducers, thinners, and other materials... calculated equivalent allowable mass based on the organic HAP and solids contents of the inks, coatings... (b)(1) through (b)(10) of this section: (1) Demonstrate that each ink, coating, varnish, adhesive...

A study on the applicability of in-line measurements in the monitoring of the pellet coating process.

PubMed

Hudovornik, Grega; Korasa, Klemen; Vrečer, Franc

2015-07-30

Special populations including paediatric and elderly patients often need advanced approaches in treatment, such as one-a-day dosing, which is achieved with modified release formulations or alternative routes of applications such as nasogastric route. Pellets are a dosage form that is frequently used in such formulations. The aim of the present work was to study the applicability of two in-line techniques, namely, Near Infrared Spectroscopy (NIR) and Spatial Filtering Technique (SFT) in the pellet coating process. The first objective of our work was to develop a prediction model for moisture content determination with the in-line NIR and to test its robustness in terms of sensitivity to changes in composition of the pellets and performance in wide range of moisture content. Secondly, the in-line SFT measurement was correlated with different off-line particle size methods. The third objective was to evaluate the ability of both in-line techniques for the detection of undesired deviations during the process, such as pellet attrition and agglomeration. Finally, the ability to predict coating thickness with the in-line NIR probe was evaluated. Results suggested that NIR prediction model for moisture content was less robust outside the calibration range and was also sensitive to changes in composition of the film coating. Nevertheless, satisfactory prediction was achieved in the case when coating composition was partially altered and adequate calibration range was used. The SFT probe results were in good correlation with off-line particle size measurement methods and proved to be an effective tool for coating thickness determination during the coating, however, the probe failed to accurately show the actual amount of the agglomerates formed during the process. In experiment when pellet attrition was initiated, both probes successfully detected abrasion of the pellet surface in real time. Furthermore, a predictive NIR model for coating thickness was made and showed a good potential to measure coating thickness in-line, suggesting that the NIR probe can be used as a single tool to monitor water content, coating thickness, and deviations in the coating process. Copyright © 2015 Elsevier B.V. All rights reserved.

Seed Nutrition and Quality, Seed Coat Boron and Lignin Are Influenced by Delayed Harvest in Exotically-Derived Soybean Breeding Lines under High Heat.

PubMed

Bellaloui, Nacer; Smith, James R; Mengistu, Alemu

2017-01-01

The timing of harvest is a major factor affecting seed quality in soybean, particularly in Midsouthern USA, when rain during harvest period is not uncommon. The objective of this research was to evaluate the effects of time of harvest on soybean seed quality (seed composition, germination, seed coat boron, and lignin) in high germinability (HG) breeding lines (50% exotic) developed under high heat. The hypothesis was that seeds of HG lines possess physiological and genetic traits for a better seed quality at harvest maturity and delayed harvest. A 2-year field experiment was conducted under irrigated conditions. Results showed that, at harvest maturity, the exotic HG lines had higher seed protein, oleic acid, sugars, seed coat boron, and seed coat lignin, but lower seed oil compared with the non-exotic checks (Control), confirming our hypothesis. At 28 days after harvest maturity (delayed harvest), the content of seed protein, oleic acid, sugars, seed coat boron, and seed coat lignin were higher in some of the HG lines compared with the checks, indicating a possible involvement of these seed constituents, especially seed coat boron and seed coat lignin, in maintaining seed coat integrity and protecting seed coat against physical damage. Highly significant positive correlations were found between germination and seed protein, oleic acid, sugars, and seed coat boron and seed coat lignin. Highly significant negative correlation was found between germination and oil, linoleic acid, seed coat wrinkling, shattering, and hard seed. Yields of some HG lines were competitive with checks. This research demonstrated that time of harvesting is an important factor influencing seed protein and oil production. Also, since high oleic acid is desirable for oxidative stability, shelf-life and biodiesel properties, using HG lines could positively influence these important traits. This result should suggest to breeders of some of the advantages of selecting for high seed coat boron and lignin, and inform growers of the importance of timely harvest for maintaining high seed quality.

Multi-chamber deposition system

DOEpatents

Jacobson, Richard L.; Jeffrey, Frank R.; Westerberg, Roger K.

1989-10-17

A system for the simultaneous deposition of different coatings onto a thin web within a large volume vacuum chamber is disclosed which chamber is provided with a plurality of deposition chambers in which the different layers are deposited onto the film as its moves from a supply roll to a finished take-up roll of coated web. The deposition chambers provided within the large vacuum chamber are provided with separate seals which minimize back diffusion of any dopant gas from adjacent deposition chambers.

Multi-chamber deposition system

DOEpatents

Jacobson, Richard L.; Jeffrey, Frank R.; Westerberg, Roger K.

1989-06-27

A system for the simultaneous deposition of different coatings onto a thin web within a large volume vacuum chamber is disclosed which chamber is provided with a plurality of deposition chambers in which the different layers are deposited onto the film as its moves from a supply roll to a finished take-up roll of coated web. The deposition chambers provided within the large vacuum chamber are provided with separate seals which minimize back diffusion of any dopant gas from adjacent deposition chambers.

Optical coherence tomography as a novel tool for in-line monitoring of a pharmaceutical film-coating process.

PubMed

Markl, Daniel; Hannesschläger, Günther; Sacher, Stephan; Leitner, Michael; Khinast, Johannes G

2014-05-13

Optical coherence tomography (OCT) is a contact-free non-destructive high-resolution imaging technique based on low-coherence interferometry. This study investigates the application of spectral-domain OCT as an in-line quality control tool for monitoring pharmaceutical film-coated tablets. OCT images of several commercially-available film-coated tablets of different shapes, formulations and coating thicknesses were captured off-line using two OCT systems with centre wavelengths of 830nm and 1325nm. Based on the off-line image evaluation, another OCT system operating at a shorter wavelength was selected to study the feasibility of OCT as an in-line monitoring method. Since in spectral-domain OCT motion artefacts can occur as a result of the tablet or sensor head movement, a basic understanding of the relationship between the tablet speed and the motion effects is essential for correct quantifying and qualifying of the tablet coating. Experimental data was acquired by moving the sensor head of the OCT system across a static tablet bed. Although examining the homogeneity of the coating turned more difficult with increasing transverse speed of the tablets, the determination of the coating thickness was still highly accurate at a speed up to 0.7m/s. The presented OCT setup enables the investigation of the intra- and inter-tablet coating uniformity in-line during the coating process. Copyright © 2014 Elsevier B.V. All rights reserved.

A novel in-line NIR spectroscopy application for the monitoring of tablet film coating in an industrial scale process.

PubMed

Möltgen, C-V; Puchert, T; Menezes, J C; Lochmann, D; Reich, G

2012-04-15

Film coating of tablets is a multivariate pharmaceutical unit operation. In this study an innovative in-line Fourier-Transform Near-Infrared Spectroscopy (FT-NIRS) application is described which enables real-time monitoring of a full industrial scale pan coating process of heart-shaped tablets. The tablets were coated with a thin hydroxypropyl methylcellulose (HPMC) film of up to approx. 28 μm on the tablet face as determined by SEM, corresponding to a weight gain of 2.26%. For a better understanding of the aqueous coating process the NIR probe was positioned inside the rotating tablet bed. Five full scale experimental runs have been performed to evaluate the impact of process variables such as pan rotation, exhaust air temperature, spray rate and pan load and elaborate robust and selective quantitative calibration models for the real-time determination of both coating growth and tablet moisture content. Principal Component (PC) score plots allowed each coating step, namely preheating, spraying and drying to be distinguished and the dominating factors and their spectral effects to be identified (e.g. temperature, moisture, coating growth, change of tablet bed density, and core/coat interactions). The distinct separation of HPMC coating growth and tablet moisture in different PCs enabled a real-time in-line monitoring of both attributes. A PLS calibration model based on Karl Fischer reference values allowed the tablet moisture trajectory to be determined throughout the entire coating process. A 1-latent variable iPLS weight gain calibration model with calibration samples from process stages dominated by the coating growth (i.e. ≥ 30% of the theoretically applied amount of coating) was sufficiently selective and accurate to predict the progress of the thin HPMC coating layer. At-line NIR Chemical Imaging (NIR-CI) in combination with PLS Discriminant Analysis (PLSDA) verified the HPMC coating growth and physical changes at the core/coat interface during the initial stages of the coating process. In addition, inter- and intra-tablet coating variability throughout the process could be assessed. These results clearly demonstrate that in-line NIRS and at-line NIR-CI can be applied as complimentary PAT tools to monitor a challenging pan coating process. Copyright © 2012 Elsevier B.V. All rights reserved.

40 CFR 63.821 - Designation of affected sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... packaging rotogravure or wide-web flexographic printing presses at a facility plus any other equipment at... packaging rotogravure or wide-web flexographic press which is used primarily for coating, laminating, or... applied by the press using wide-web flexographic print stations in each month never exceeds 5 percent of...

Effectiveness of off-line and web-based promotion of health information web sites.

PubMed

Jones, Craig E; Pinnock, Carole B

2002-01-01

The relative effectiveness of off-line and web-based promotional activities in increasing the use of health information web sites by target audiences were compared. Visitor sessions were classified according to their method of arrival at the site (referral) as external web site, search engine, or "no referrer" (i.e., visitor arriving at the site by inputting URL or using bookmarks). The number of Australian visitor sessions correlated with no referrer referrals but not web site or search-engine referrals. Results showed that the targeted consumer group is more likely to access the web site as a result of off-line promotional activities. The properties of target audiences likely to influence the effectiveness of off-line versus on-line promotional strategies include the size of the Internet using population of the target audience, their proficiency in the use of the Internet, and the increase in effectiveness of off-line promotional activities when applied to locally defined target audiences.

In line NIR quantification of film thickness on pharmaceutical pellets during a fluid bed coating process.

PubMed

Lee, Min-Jeong; Seo, Da-Young; Lee, Hea-Eun; Wang, In-Chun; Kim, Woo-Sik; Jeong, Myung-Yung; Choi, Guang J

2011-01-17

Along with the risk-based approach, process analytical technology (PAT) has emerged as one of the key elements to fully implement QbD (quality-by-design). Near-infrared (NIR) spectroscopy has been extensively applied as an in-line/on-line analytical tool in biomedical and chemical industries. In this study, the film thickness on pharmaceutical pellets was examined for quantification using in-line NIR spectroscopy during a fluid-bed coating process. A precise monitoring of coating thickness and its prediction with a suitable control strategy is crucial to the quality assurance of solid dosage forms including dissolution characteristics. Pellets of a test formulation were manufactured and coated in a fluid-bed by spraying a hydroxypropyl methylcellulose (HPMC) coating solution. NIR spectra were acquired via a fiber-optic probe during the coating process, followed by multivariate analysis utilizing partial least squares (PLS) calibration models. The actual coating thickness of pellets was measured by two separate methods, confocal laser scanning microscopy (CLSM) and laser diffraction particle size analysis (LD-PSA). Both characterization methods gave superb correlation results, and all determination coefficient (R(2)) values exceeded 0.995. In addition, a prediction coating experiment for 70min demonstrated that the end-point can be accurately designated via NIR in-line monitoring with appropriate calibration models. In conclusion, our approach combining in-line NIR monitoring with CLSM and LD-PSA can be applied as an effective PAT tool for fluid-bed pellet coating processes. Copyright © 2010 Elsevier B.V. All rights reserved.

In-line agglomeration degree estimation in fluidized bed pellet coating processes using visual imaging.

PubMed

Mehle, Andraž; Kitak, Domen; Podrekar, Gregor; Likar, Boštjan; Tomaževič, Dejan

2018-05-09

Agglomeration of pellets in fluidized bed coating processes is an undesirable phenomenon that affects the yield and quality of the product. In scope of PAT guidance, we present a system that utilizes visual imaging for in-line monitoring of the agglomeration degree. Seven pilot-scale Wurster coating processes were executed under various process conditions, providing a wide spectrum of process outcomes. Images of pellets were acquired during the coating processes in a contactless manner through an observation window of the coating apparatus. Efficient image analysis methods were developed for automatic recognition of discrete pellets and agglomerates in the acquired images. In-line obtained agglomeration degree trends revealed the agglomeration dynamics in distinct phases of the coating processes. We compared the in-line estimated agglomeration degree in the end point of each process to the results obtained by the off-line sieve analysis reference method. A strong positive correlation was obtained (coefficient of determination R 2 =0.99), confirming the feasibility of the approach. The in-line estimated agglomeration degree enables early detection of agglomeration and provides means for timely interventions to retain it in an acceptable range. Copyright © 2018 Elsevier B.V. All rights reserved.

Parallel Simulation of Three-Dimensional Free-Surface Fluid Flow Problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

BAER,THOMAS A.; SUBIA,SAMUEL R.; SACKINGER,PHILIP A.

2000-01-18

We describe parallel simulations of viscous, incompressible, free surface, Newtonian fluid flow problems that include dynamic contact lines. The Galerlin finite element method was used to discretize the fully-coupled governing conservation equations and a ''pseudo-solid'' mesh mapping approach was used to determine the shape of the free surface. In this approach, the finite element mesh is allowed to deform to satisfy quasi-static solid mechanics equations subject to geometric or kinematic constraints on the boundaries. As a result, nodal displacements must be included in the set of problem unknowns. Issues concerning the proper constraints along the solid-fluid dynamic contact line inmore » three dimensions are discussed. Parallel computations are carried out for an example taken from the coating flow industry, flow in the vicinity of a slot coater edge. This is a three-dimensional free-surface problem possessing a contact line that advances at the web speed in one region but transitions to static behavior in another part of the flow domain. Discussion focuses on parallel speedups for fixed problem size, a class of problems of immediate practical importance.« less

Reflectance infrared spectroscopy for in-line monitoring of nicotine during a coating process for an oral thin film.

PubMed

Hammes, Florian; Hille, Thomas; Kissel, Thomas

2014-02-01

A process analytical method using reflectance infrared spectrometry was developed for the in-line monitoring of the amount of the active pharmaceutical ingredient (API) nicotine during a coating process for an oral thin film (OTF). In-line measurements were made using a reflectance infrared (RI) sensor positioned after the last drying zone of the coating line. Real-time spectra from the coating process were used for modelling the nicotine content. Partial least squares (PLS1) calibration models with different data pre-treatments were generated. The calibration model with the most comparable standard error of calibration (SEC) and the standard error of cross validation (SECV) was selected for an external validation run on the production coating line with an independent laminate. Good correlations could be obtained between values estimated from the reflectance infrared data and the reference HPLC test method, respectively. With in-line measurements it was possible to allow real-time adjustments during the production process to keep product specifications within predefined limits hence avoiding loss of material and batch. Copyright © 2013 Elsevier B.V. All rights reserved.

Diffractive optical element-based glossmeter for the on-line measurement of normal reflectance on a printed porous coated paper

NASA Astrophysics Data System (ADS)

Oksman, Antti; Kuivalainen, Kalle; Ta˚G, Carl-Mikael; Juuti, Mikko; Mattila, Rauno; Hietala, Eero; Gane, Patrick A. C.; Peiponen, Kai-Erik

2011-04-01

Gloss of a product, such as print gloss, is mainly inspected with conventional white light glossmeters both at laboratory or production facilities. However, problems occur in conventional gloss measurement when the inspected surface is vertically moved in the plane of incidence and reflection or when the measurement area is small or curved. For a partial solution to these problems, we have previously introduced diffractive optical element-based glossmeters (DOGs) for the gloss inspection in laboratories and off-line use. We present a new construction of DOG, termed μDOG 1D, for the one-dimensional on-line print gloss measurement, in the form of the reflectance determination normal to the surface. The function of the glossmeter is demonstrated by laboratory tests and on-line measurements at a heat-set web offset printing machine. It is shown that gloss (i.e., normal reflectance) and minute gloss variation of papers and prints can be measured at the printing line using the glossmeter. This glossmeter is expected to be useful in real-time monitoring of the gloss and surface-specific absorption not only in the printing industry but also in inspection of products in other industrial sectors, such as metal finishing, laminating, paper, and construction materials manufacturing.

Automated pharmaceutical tablet coating layer evaluation of optical coherence tomography images

NASA Astrophysics Data System (ADS)

Markl, Daniel; Hannesschläger, Günther; Sacher, Stephan; Leitner, Michael; Khinast, Johannes G.; Buchsbaum, Andreas

2015-03-01

Film coating of pharmaceutical tablets is often applied to influence the drug release behaviour. The coating characteristics such as thickness and uniformity are critical quality parameters, which need to be precisely controlled. Optical coherence tomography (OCT) shows not only high potential for off-line quality control of film-coated tablets but also for in-line monitoring of coating processes. However, an in-line quality control tool must be able to determine coating thickness measurements automatically and in real-time. This study proposes an automatic thickness evaluation algorithm for bi-convex tables, which provides about 1000 thickness measurements within 1 s. Beside the segmentation of the coating layer, optical distortions due to refraction of the beam by the air/coating interface are corrected. Moreover, during in-line monitoring the tablets might be in oblique orientation, which needs to be considered in the algorithm design. Experiments were conducted where the tablet was rotated to specified angles. Manual and automatic thickness measurements were compared for varying coating thicknesses, angles of rotations, and beam displacements (i.e. lateral displacement between successive depth scans). The automatic thickness determination algorithm provides highly accurate results up to an angle of rotation of 30°. The computation time was reduced to 0.53 s for 700 thickness measurements by introducing feasibility constraints in the algorithm.

Simulation to coating weight control for galvanizing

NASA Astrophysics Data System (ADS)

Wang, Junsheng; Yan, Zhang; Wu, Kunkui; Song, Lei

2013-05-01

Zinc coating weight control is one of the most critical issues for continuous galvanizing line. The process has the characteristic of variable-time large time delay, nonlinear, multivariable. It can result in seriously coating weight error and non-uniform coating. We develop a control system, which can automatically control the air knives pressure and its position to give a constant and uniform zinc coating, in accordance with customer-order specification through an auto-adaptive empirical model-based feed forward adaptive controller, and two model-free adaptive feedback controllers . The proposed models with controller were applied to continuous galvanizing line (CGL) at Angang Steel Works. By the production results, the precise and stability of the control model reduces over-coating weight and improves coating uniform. The product for this hot dip galvanizing line does not only satisfy the customers' quality requirement but also save the zinc consumption.

40 CFR 63.4320 - By what date must I conduct the initial compliance demonstration?

Code of Federal Regulations, 2010 CFR

2010-07-01

... period, the organic HAP content of each coating and printing material you applied and the mass fraction... applicable limit in Table 1 to this subpart, and documentation that in web coating/printing operations you...

Vacuum-deposited polymer/silver reflector material

NASA Astrophysics Data System (ADS)

Affinito, John D.; Martin, Peter M.; Gross, Mark E.; Bennett, Wendy D.

1994-09-01

Weatherable, low cost, front surface, solar reflectors on flexible substrates would be highly desirable for lamination to solar concentrator panels. The method to be described in this paper may permit such reflector material to be fabricated for less the 50$CNT per square foot. Vacuum deposited Polymer/Silver/Polymer reflectors and Fabry-Perot interference filters were fabricated in a vacuum web coating operation on polyester substrates. Reflectivities were measured in the wavelength range from .4 micrometers to .8 micrometers . It is hoped that a low cost substrate can be used with the substrate laminated to the concentrator and the weatherable acrylic polymer coating facing the sun. This technique should be capable of deposition line speeds approaching 1500 linear feet/minute2. Central to this technique is a new vacuum deposition process for the high rate deposition of polymer films. This polymer process involves the flash evaporation of an acrylic monomer onto a moving substrate. The monomer is subsequently cured by an electron beam or ultraviolet light. This high speed polymer film deposition process has been named the PML process- for Polymer Multi- Layer.

Diversity of selected Lupinus angustifolius L. genotypes at the phenotypic and DNA level with respect to microscopic seed coat structure and thickness.

PubMed

Clements, Jon; Galek, Renata; Kozak, Bartosz; Michalczyk, Dariusz Jan; Piotrowicz-Cieślak, Agnieszka Iwona; Sawicka-Sienkiewicz, Ewa; Stawiński, Stanislaw; Zalewski, Dariusz

2014-01-01

The paper investigates seed coat characteristics (as a percentage of overall seed diameter) in Lupinus angustifolius L., a potential forage crop. In the study ten L. angustifolius genotypes, including three Polish cultivars, two Australian cultivars, three mutants originated from cv. 'Emir', and one Belarusian and one Australian breeding line were evaluated. The highest seed coat percentage was recorded in cultivars 'Sonet' and 'Emir'. The lowest seed coat thickness percentage (below 20%) was noted for breeding lines 11257-19, LAG24 and cultivar 'Zeus' (17.87%, 18.91% 19.60%, respectively). Despite having low seed weight, the Australian line no. 11257-19 was characterized by a desirable proportion of seed coat to the weight of seeds. In general, estimation of the correlation coefficient indicated a tendency that larger seeds had thinner coats. Scanning Electron Microscopy images showed low variation of seed coat sculpture and the top of seeds covered with a cuticle. Most of the studied genotypes were characterized by a cristatepapillate seed coat surface, formed by elongated polygonal cells. Only breeding line no. 11267-19 had a different shape of the cells building the surface layer of the coat. In order to illustrate genetic diversity among the genotypes tested, 24 ISSR primers were used. They generated a total of 161 polymorphic amplification products in 10 evaluated narrow-leaved lupin genotypes.

Measurement of the Intertablet Coating Uniformity of a Pharmaceutical Pan Coating Process With Combined Terahertz and Optical Coherence Tomography In-Line Sensing.

PubMed

Lin, Hungyen; Dong, Yue; Markl, Daniel; Williams, Bryan M; Zheng, Yalin; Shen, Yaochun; Zeitler, J Axel

2017-04-01

We present in-line coating thickness measurements acquired simultaneously using 2 independent sensing modalities: terahertz pulsed imaging (TPI) and optical coherence tomography (OCT). Both techniques are sufficiently fast to resolve the coating thickness of individual pharmaceutical tablets in situ during the film coating operation, and both techniques are direct structural imaging techniques that do not require multivariate calibration. The TPI sensor is suitable to measure coatings greater than 50 μm and can penetrate through thick coatings even in the presence of pigments over a wide range of excipients. Due to the long wavelength, terahertz radiation is not affected by scattering from dust within the coater. In contrast, OCT can resolve coating layers as thin as 20 μm and is capable of measuring the intratablet coating uniformity and the intertablet coating thickness distribution within the coating pan. However, the OCT technique is less robust when it comes to the compatibility with excipients, dust, and potentially the maximum coating thickness that can be resolved. Using a custom-built laboratory scale coating unit, the coating thickness measurements were acquired independently by the TPI and OCT sensors throughout a film coating operation. Results of the in-line TPI and OCT measurements were compared against one another and validated with off-line TPI and weight gain measurements. Compared with other process analytical technology sensors, such as near-infrared and Raman spectroscopy, the TPI and OCT sensors can resolve the intertablet thickness distribution based on sampling a significant fraction of the tablet populations in the process. By combining 2 complementary sensing modalities, it was possible to seamlessly monitor the coating process over the range of film thickness from 20 μm to greater than 250 μm. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

An accurate and efficient method for piezoelectric coated functional devices based on the two-dimensional Green’s function for a normal line force and line charge

NASA Astrophysics Data System (ADS)

Hou, Peng-Fei; Zhang, Yang

2017-09-01

Because most piezoelectric functional devices, including sensors, actuators and energy harvesters, are in the form of a piezoelectric coated structure, it is valuable to present an accurate and efficient method for obtaining the electro-mechanical coupling fields of this coated structure under mechanical and electrical loads. With this aim, the two-dimensional Green’s function for a normal line force and line charge on the surface of coated structure, which is a combination of an orthotropic piezoelectric coating and orthotropic elastic substrate, is presented in the form of elementary functions based on the general solution method. The corresponding electro-mechanical coupling fields of this coated structure under arbitrary mechanical and electrical loads can then be obtained by the superposition principle and Gauss integration. Numerical results show that the presented method has high computational precision, efficiency and stability. It can be used to design the best coating thickness in functional devices, improve the sensitivity of sensors, and improve the efficiency of actuators and energy harvesters. This method could be an efficient tool for engineers in engineering applications.

Changes in polyphenols of the seed coat during the after-darkening process in pinto beans (Phaseolus vulgaris L.).

PubMed

Beninger, Clifford W; Gu, Liwei; Prior, Ronald L; Junk, Donna C; Vandenberg, Albert; Bett, Kirstin E

2005-10-05

Proanthocyanidins and flavonoids were isolated and identified from seed coats of two aged and nonaged pinto bean lines: 1533-15 and CDC Pintium. The seed coat of 1533-15 darkens slowly and never darkens to the same extent as CDC Pintium. Analysis of the overall level of proanthocyanidins using a vanillin assay demonstrated that aged and nonaged seed coats of CDC Pintium had significantly higher levels of proanthocyanidins than aged and nonaged 1533-15 seed coats. Aged and nonaged seed coats of both lines were found to contain one main flavonol monomer, kaempferol, and three minor flavonols, kaempferol 3-O-glucoside, kaempferol 3-O-glucosylxylose, and kaempferol 3-O-acetylglucoside. These compounds were identified by NMR and ESI-MS analysis (except for kaempferol 3-O-acetylglucoside, which was tentatively identified only by ESI-MS analysis) and quantified using HPLC-DAD. The combined concentrations of all the kaempferol compounds in seed coats of CDC Pintium were significantly higher than in seed coats of 1533-15, and the combined contents did not change after aging. The content of kaempferol decreased nearly by half in the seed coats of CDC Pintium after aging, whereas no significant change was observed in the seed coats of 1533-15. Proanthocyanidin fractions from both lines, aged and nonaged, were subjected to LC-MS/MS analysis and found to be composed primarily of procyanidins. Procyanidins in the seed coats were predominantly polymers with the degree of polymers higher than 10. The proportion of these polymers decreased after aging, while that of the low-molecular-weight procyanidins increased. A catechin-kaempferol adduct was tentatively identified in both lines by LC-MS/MS, and the concentration increased in the seed coats after aging.

Nanocrystalline films for gas-reactive applications

DOEpatents

Eastman, Jeffrey A.; Thompson, Loren J.

2004-02-17

A gas sensor for detection of oxidizing and reducing gases, including O.sub.2, CO.sub.2, CO, and H.sub.2, monitors the partial pressure of a gas to be detected by measuring the temperature rise of an oxide-thin-film-coated metallic line in response to an applied electrical current. For a fixed input power, the temperature rise of the metallic line is inversely proportional to the thermal conductivity of the oxide coating. The oxide coating contains multi-valent cation species that change their valence, and hence the oxygen stoichiometry of the coating, in response to changes in the partial pressure of the detected gas. Since the thermal conductivity of the coating is dependent on its oxygen stoichiometry, the temperature rise of the metallic line depends on the partial pressure of the detected gas. Nanocrystalline (<100 nm grain size) oxide coatings yield faster sensor response times than conventional larger-grained coatings due to faster oxygen diffusion along grain boundaries rather than through grain interiors.

Electrochromic properties of polyaniline-coated fiber webs for tissue engineering applications.

PubMed

Beregoi, Mihaela; Busuioc, Cristina; Evanghelidis, Alexandru; Matei, Elena; Iordache, Florin; Radu, Mihaela; Dinischiotu, Anca; Enculescu, Ionut

2016-08-30

By combining the electrospinning method advantages (high surface-to-volume ratio, controlled morphology, varied composition and flexibility for the resulting structures) with the electrical activity of polyaniline, a new core-shell-type material with potential applications in the field of artificial muscles was synthesized. Thus, a poly(methylmethacrylate) solution was electrospun in optimized conditions to obtain randomly oriented polymer fiber webs. Further, a gold layer was sputtered on their surface in order to make them conductive and improve the mechanical properties. The metalized fiber webs were then covered with a PANI layer by in situ electrochemical polymerization starting from aniline and using sulphuric acid as oxidizing agent. By applying a small voltage on PANI-coated fiber webs in the presence of an electrolyte, the oxidation state of PANI changes, which is followed by the device color modification. The morphological, electrical and biological properties of the resulting multilayered material were also investigated. Copyright © 2015 Elsevier B.V. All rights reserved.

Students' Reaction to WebCT: Implications for Designing On-Line Learning Environments

ERIC Educational Resources Information Center

Osman, Mohamed Eltahir

2005-01-01

There is a growing number of web-based and web-assisted course development tools and products that can be used to create on-line learning environment. The utility of these products, however, varies greatly depending on their feasibility, prerequisite infrastructure, technical features, interface, and course development and management tools. WebCT…

Automated X-ray quality control of catalytic converters

NASA Astrophysics Data System (ADS)

Shashishekhar, N.; Veselitza, D.

2017-02-01

Catalytic converters are devices attached to the exhaust system of automobile or other engines to eliminate or substantially reduce polluting emissions. They consist of coated substrates enclosed in a stainless steel housing. The substrate is typically made of ceramic honeycombs; however stainless steel foil honeycombs are also used. The coating is usually a slurry of alumina, silica, rare earth oxides and platinum group metals. The slurry also known as the wash coat is applied to the substrate in two doses, one on each end of the substrate; in some cases multiple layers of coating are applied. X-ray imaging is used to inspect the applied coating depth on a substrate to confirm compliance with quality requirements. Automated image analysis techniques are employed to measure the coating depth from the X-ray image. Coating depth is assessed by analysis of attenuation line profiles in the image. Edge detection algorithms with noise reduction and outlier rejection are used to calculate the coating depth at a specified point along an attenuation line profile. Quality control of the product is accomplished using several attenuation line profile regions for coating depth measurements, with individual pass or fail criteria specified for each region.

Diversity of Selected Lupinus angustifolius L. Genotypes at the Phenotypic and DNA Level with Respect to Microscopic Seed Coat Structure and Thickness

PubMed Central

Clements, Jon; Galek, Renata; Kozak, Bartosz; Michalczyk, Dariusz Jan; Piotrowicz-Cieślak, Agnieszka Iwona; Sawicka-Sienkiewicz, Ewa; Stawiński, Stanislaw; Zalewski, Dariusz

2014-01-01

The paper investigates seed coat characteristics (as a percentage of overall seed diameter) in Lupinus angustifolius L., a potential forage crop. In the study ten L. angustifolius genotypes, including three Polish cultivars, two Australian cultivars, three mutants originated from cv. ‘Emir’, and one Belarusian and one Australian breeding line were evaluated. The highest seed coat percentage was recorded in cultivars ‘Sonet’ and ‘Emir’. The lowest seed coat thickness percentage (below 20%) was noted for breeding lines 11257-19, LAG24 and cultivar ‘Zeus’ (17.87%, 18.91% 19.60%, respectively). Despite having low seed weight, the Australian line no. 11257-19 was characterized by a desirable proportion of seed coat to the weight of seeds. In general, estimation of the correlation coefficient indicated a tendency that larger seeds had thinner coats. Scanning Electron Microscopy images showed low variation of seed coat sculpture and the top of seeds covered with a cuticle. Most of the studied genotypes were characterized by a cristatepapillate seed coat surface, formed by elongated polygonal cells. Only breeding line no. 11267-19 had a different shape of the cells building the surface layer of the coat. In order to illustrate genetic diversity among the genotypes tested, 24 ISSR primers were used. They generated a total of 161 polymorphic amplification products in 10 evaluated narrow-leaved lupin genotypes. PMID:25119983

Thermoplastic coating of carbon fibers

NASA Technical Reports Server (NTRS)

Edie, D. D.; Lickfield, G. C.; Allen, L. E.; Mccollum, J. R.

1989-01-01

A continuous powder coating system was developed for coating carbon fiber with LaRC-TPI (Langley Research Center-Thermoplastic Polyimide), a high-temperature thermoplastic polymide invented by NASA-Langley. The coating line developed used a pneumatic fiber spreader to separate the individual fibers. The polymer was applied within a recirculating powder coating chamber then melted using a combination of direct electrical resistance and convective heating to make it adhere to the fiber tow. The tension and speed of the line were controlled with a dancer arm and an electrically driven fiber wind-up and wind-off. The effects of heating during the coating process on the flexibility of the prepreg produced were investigated. The uniformity with which the fiber tow could be coated with polymer also was examined. Composite specimens were fabricated from the prepreg and tested to determine optimum process conditions. The study showed that a very uniform and flexible prepeg with up to 50 percent by volume polymer could be produced with this powder coating system. The coating line minimized powder loss and produced prepeg in lengths of up to 300 m. The fiber spreading was found to have a major effect on the coating uniformity and flexibility. Though test results showed low composite tensile strengths, analysis of fracture surfaces under scanning electron microscope indicated that fiber/matrix adhesion was adequate.

How Did the Spider Cross the River? Behavioral Adaptations for River-Bridging Webs in Caerostris darwini (Araneae: Araneidae)

PubMed Central

Gregorič, Matjaž; Agnarsson, Ingi; Blackledge, Todd A.; Kuntner, Matjaž

2011-01-01

Background Interspecific coevolution is well described, but we know significantly less about how multiple traits coevolve within a species, particularly between behavioral traits and biomechanical properties of animals' “extended phenotypes”. In orb weaving spiders, coevolution of spider behavior with ecological and physical traits of their webs is expected. Darwin's bark spider (Caerostris darwini) bridges large water bodies, building the largest known orb webs utilizing the toughest known silk. Here, we examine C. darwini web building behaviors to establish how bridge lines are formed over water. We also test the prediction that this spider's unique web ecology and architecture coevolved with new web building behaviors. Methodology We observed C. darwini in its natural habitat and filmed web building. We observed 90 web building events, and compared web building behaviors to other species of orb web spiders. Conclusions Caerostris darwini uses a unique set of behaviors, some unknown in other spiders, to construct its enormous webs. First, the spiders release unusually large amounts of bridging silk into the air, which is then carried downwind, across the water body, establishing bridge lines. Second, the spiders perform almost no web site exploration. Third, they construct the orb capture area below the initial bridge line. In contrast to all known orb-weavers, the web hub is therefore not part of the initial bridge line but is instead built de novo. Fourth, the orb contains two types of radial threads, with those in the upper half of the web doubled. These unique behaviors result in a giant, yet rather simplified web. Our results continue to build evidence for the coevolution of behavioral (web building), ecological (web microhabitat) and biomaterial (silk biomechanics) traits that combined allow C. darwini to occupy a unique niche among spiders. PMID:22046378

Pharmaceutical Film Coating Catalog for Spectral Domain Optical Coherence Tomography.

PubMed

Lin, Hungyen; Dong, Yue; Markl, Daniel; Zhang, Zijian; Shen, Yaochun; Zeitler, J Axel

2017-10-01

Optical coherence tomography (OCT) has recently been demonstrated to measure the film coating thickness of pharmaceutical tablets and pellets directly. The results enable the analysis of inter- and intra-tablet coating variability at an off-line and in-line setting. To date, only a few coating formulations have been tried and there is very little information on the applicability of OCT to other coatings. As it is well documented that optical methods including OCT are prone to scattering leading to limited penetration, some pharmaceutical coatings may not be measurable altogether. This study presents OCT measurements of 22 different common coatings for the assessment of OCT applicability. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Impact of humidity on functionality of on-paper printed electronics.

PubMed

Bollström, Roger; Pettersson, Fredrik; Dolietis, Peter; Preston, Janet; Osterbacka, Ronald; Toivakka, Martti

2014-03-07

A multilayer coated paper substrate, combining barrier and printability properties was manufactured utilizing a pilot-scale slide curtain coating technique. The coating structure consists of a thin mineral pigment layer coated on top of a barrier layer. The surface properties, i.e. smoothness and surface porosity, were adjusted by the choice of calendering parameters. The influence of surface properties on the fine line printability and conductivity of inkjet-printed silver lines was studied. Surface roughness played a significant role when printing narrow lines, increasing the risk of defects and discontinuities, whereas for wider lines the influence of surface roughness was less critical. A smooth, calendered surface resulted in finer line definition, i.e. less edge raggedness. Dimensional stability and its influence on substrate surface properties as well as on the functionality of conductive tracks and transistors were studied by exposure to high/low humidity cycles. The barrier layer of the multilayer coated paper reduced the dimensional changes and surface roughness increase caused by humidity and helped maintain the conductivity of the printed tracks. Functionality of a printed transistor during a short, one hour humidity cycle was maintained, but a longer exposure to humidity destroyed the non-encapsulated transistor.

Rubber-coated bellows improves vibration damping in vacuum lines

NASA Technical Reports Server (NTRS)

Hegland, D. E.; Smith, R. J.

1966-01-01

Compact-vibration damping systems, consisting of rubber-coated metal bellows with a sliding O-ring connector, are used in vacuum lines. The device presents a metallic surface to the vacuum system and combines flexibility with the necessary stiffness. It protects against physical damage, reduces fatigue failure, and provides easy mating of nonparallel lines.

40 CFR 63.4360 - What are the general requirements for performance tests?

Code of Federal Regulations, 2010 CFR

2010-07-01

... obtain a waiver of the performance test according to the provisions in § 63.7(h). (1) Representative web... under representative operating conditions for the web coating/printing or dyeing/finishing operation...) Representative emission capture system and add-on control device operating conditions. You must conduct the...

Progress in the development of advanced solar reflectors

NASA Astrophysics Data System (ADS)

Kennedy, C.; Jorgensen, G.

1994-01-01

Solar thermal technologies require large mirrors to provide concentrated sunlight for renewable power generation. Such materials must be inexpensive and maintain high specular reflectance for extended lifetimes in severe outdoor environments. Polymer reflectors are lighter than glass mirrors, offer greater system design flexibility, and have the potential for lower cost. During the past year, collaborative cost-shared research and development between the National Renewable Energy Laboratory (NREL) and industrial partners has identified candidate materials that perform better than the state-of-the-art commercial silvered-polymer reflectors in terms of corrosion degradation and resistance to delamination failure. Additional cooperative efforts will produce new alternative materials with reduced costs due to high speed production line capability. NREL welcomes continued and expanded interest and web coating industry involvement in developing advanced solar reflector materials.

Review of Thermal Spray Coating Applications in the Steel Industry: Part 2—Zinc Pot Hardware in the Continuous Galvanizing Line

NASA Astrophysics Data System (ADS)

Matthews, S.; James, B.

2010-12-01

This two-part article series reviews the application of thermal spray coating technology in the production of steel and steel sheet products. Part 2 of this article series is dedicated to coating solutions in the continuous galvanizing line. The corrosion mechanisms of Fe- and Co-based bulk materials are briefly reviewed as a basis for the development of thermal spray coating solutions. WC-Co thermal spray coatings are commonly applied to low Al-content galvanizing hardware due to their superior corrosion resistance compared to Fe and Co alloys. The effect of phase degradation, carbon content, and WC grain size are discussed. At high Al concentrations, the properties of WC-Co coatings degrade significantly, leading to the application of oxide-based coatings and corrosion-resistant boride containing coatings. The latest results of testing are summarized, highlighting the critical coating parameters.

46 CFR 160.055-1 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Repellant Treated. MIL-W-17337D—Webbing, Woven, Nylon. MIL-C-43006D—Cloth and Strip Laminated, Vinyl-Nylon High Strength, Flexible. (2) Federal Specifications: CCC-C-700G—Cloth, Coated, Vinyl, Coated (Artificial Leather). CCC-C-426D—Cloth, Drill, Cotton. (3) Federal Standards: No. 191—Textile Test Methods. No...

46 CFR 160.055-1 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Repellant Treated. MIL-W-17337D—Webbing, Woven, Nylon. MIL-C-43006D—Cloth and Strip Laminated, Vinyl-Nylon High Strength, Flexible. (2) Federal Specifications: CCC-C-700G—Cloth, Coated, Vinyl, Coated (Artificial Leather). CCC-C-426D—Cloth, Drill, Cotton. (3) Federal Standards: No. 191—Textile Test Methods. No...

46 CFR 160.055-1 - Incorporation by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Repellant Treated. MIL-W-17337D—Webbing, Woven, Nylon. MIL-C-43006D—Cloth and Strip Laminated, Vinyl-Nylon High Strength, Flexible. (2) Federal Specifications: CCC-C-700G—Cloth, Coated, Vinyl, Coated (Artificial Leather). CCC-C-426D—Cloth, Drill, Cotton. (3) Federal Standards: No. 191—Textile Test Methods. No...

46 CFR 160.055-1 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Repellant Treated. MIL-W-17337D—Webbing, Woven, Nylon. MIL-C-43006D—Cloth and Strip Laminated, Vinyl-Nylon High Strength, Flexible. (2) Federal Specifications: CCC-C-700G—Cloth, Coated, Vinyl, Coated (Artificial Leather). CCC-C-426D—Cloth, Drill, Cotton. (3) Federal Standards: No. 191—Textile Test Methods. No...

Real-time data processing for in-line monitoring of a pharmaceutical coating process by optical coherence tomography

NASA Astrophysics Data System (ADS)

Markl, Daniel; Ziegler, Jakob; Hannesschläger, Günther; Sacher, Stephan; Buchsbaum, Andreas; Leitner, Michael; Khinast, Johannes G.

2014-05-01

Coating of tablets is a widely applied unit operation in the pharmaceutical industry. Thickness and uniformity of the coating layer are crucial for efficacy as well as for compliance. Not only due to different initiatives it is thus essential to monitor and control the coating process in-line. Optical coherence tomography (OCT) was already shown in previous works to be a suitable candidate for in-line monitoring of coating processes. However, to utilize the full potential of the OCT technology an automatic evaluation of the OCT measurements is essential. The automatic evaluation is currently implemented in MATLAB and includes several steps: (1) extraction of features of each A-scan, (2) classification of Ascan measurements based on their features, (3) detection of interfaces (air/coating and coating/tablet core), (4) correction of distortions due to the curvature of the bi-convex tablets and the oblique orientation of the tablets, and (5) determining the coating thickness. The algorithm is tested on OCT data acquired by moving the sensor head of the OCT system across a static tablet bed. The coating thickness variations of single tablets (i.e., intra-tablet coating variability) can additionally be analyzed as OCT allows the measurement of the coating thickness on multiple displaced positions on one single tablet. Specifically, the information about those parameters emphasizes the high capability of the OCT technology to improve process understanding and to assure a high product quality.

71 FR 66315 - Notice of Availability of Invention for Licensing; Government-Owned Invention

Federal Register 2010, 2011, 2012, 2013, 2014

2006-11-14

... Coating and Method of Formulator.//Navy Case No. 97,486: Processing Semantic Markups in Web Ontology... Rotating Clip.//Navy Case No. 97,886: Adding Semantic Support to Existing UDDI Infrastructure.//Navy Case..., Binding, and Integration of Non-Registered Geospatial Web Services.//Navy Case No. 98,094: Novel, Single...

Mapping of AFLP markers linked to seed coat colour loci in Brassica juncea (L.) Czern.

PubMed

Sabharwal, V; Negi, M S; Banga, S S; Lakshmikumaran, M

2004-06-01

Association mapping of the seed-coat colour with amplified fragment length polymorphism (AFLP) markers was carried out in 39 Brassica juncea lines. The lines had genetically diverse parentages and varied for seed-coat colour and other morphological characters. Eleven AFLP primer combinations were used to screen the 39 B. juncea lines, and a total of 335 polymorphic bands were detected. The bands were analysed for association with seed-coat colour using multiple regression analysis. This analysis revealed 15 markers associated with seed-coat colour, obtained with eight AFLP primer combinations. The marker E-ACA/M-CTG(350 )explained 69% of the variation in seed-coat colour. This marker along with markers E-AAC/M-CTC(235 )and E-AAC/M-CTA(250) explained 89% of the total variation. The 15 associated markers were validated for linkage with the seed-coat colour loci using a recombinant inbred line (RIL) mapping population. Bands were amplified with the eight AFLP primer combinations in 54 RIL progenies. Of the 15 associated markers, 11 mapped on two linkage groups. Eight markers were placed on linkage group 1 at a marker density of 6.0 cM, while the remaining three were mapped on linkage group 2 at a marker density of 3.6 cM. Marker E-ACA/M-CTG(350 )co-segregated with Gene1 controlling seed-coat colour; it was specific for yellow seed-coat colour and mapped to linkage group 1. Marker E-AAC/M-CTC(235) (AFLP8), which had been studied previously, was present on linkage group 2; it was specific for brown seed-coat colour. Since AFLP markers are not adapted for large-scale applications in plant breeding, it is important to convert these to sequence-characterised amplified region (SCAR) markers. Marker E-AAC/M-CTC(235) (AFLP8) had been previously converted into a SCAR. Work is in progress to convert the second of the linked markers, E-ACA/M-CTG(350), to a SCAR. The two linked AFLP markers converted to SCARs will be useful for developing yellow-seeded B. juncea lines by means of marker-assisted selection.

Selection of bean lines that combine resistance to web blight and common bacterial blight

USDA-ARS?s Scientific Manuscript database

Web blight caused by Thanatephorus cucumeris Frank (Donk) causes significant reductions in the yield and quality of beans produced in the humid, lowland tropics. A total of 644 lines from different breeding programs were evaluated for reaction to web blight and other diseases using conventional plan...

Ultra-Smooth As-Deposited Optical Films

DTIC Science & Technology

2004-03-31

reduction. • Conformal Coatings . Unlike other PVD processes which are strictly line-of- sight, PLASMION’s NMIBD has demonstrated the ability to create...a few days (for in-line coating machine, or roll-to-roll machine). In our project we use the box chamber and deposition materials: SiO2 and Ta2O5 ...are widely used for optical applications; these may be roughly divided into low and high technology categories. Low technology coatings (a relative

PAT-tools for process control in pharmaceutical film coating applications.

PubMed

Knop, Klaus; Kleinebudde, Peter

2013-12-05

Recent development of analytical techniques to monitor the coating process of pharmaceutical solid dosage forms such as pellets and tablets are described. The progress from off- or at-line measurements to on- or in-line applications is shown for the spectroscopic methods near infrared (NIR) and Raman spectroscopy as well as for terahertz pulsed imaging (TPI) and image analysis. The common goal of all these methods is to control or at least to monitor the coating process and/or to estimate the coating end point through timely measurements. Copyright © 2013 Elsevier B.V. All rights reserved.

Impact of Processing Conditions on Inter-tablet Coating Thickness Variations Measured by Terahertz In-Line Sensing

PubMed Central

Lin, Hungyen; May, Robert K; Evans, Michael J; Zhong, Shuncong; Gladden, Lynn F; Shen, Yaochun; Zeitler, J Axel

2015-01-01

A novel in-line technique utilising pulsed terahertz radiation for direct measurement of the film coating thickness of individual tablets during the coating process was previously developed and demonstrated on a production-scale coater. Here, we use this technique to monitor the evolution of tablet film coating thickness and its inter-tablet variability during the coating process under a number of different process conditions that have been purposefully induced in the production-scale coating process. The changes that were introduced to the coating process include removing the baffles from the coater, adding uncoated tablets to the running process, halting the drum, blockage of spray guns and changes to the spray rate. The terahertz sensor was able to pick up the resulting changes in average coating thickness in the coating drum and we report the impact of these process changes on the resulting coating quality. © 2015 The Authors. Journal of Pharmaceutical Sciences published by Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci 104:2513–2522, 2015 PMID:26037660

Coating process optimization through in-line monitoring for coating weight gain using Raman spectroscopy and design of experiments.

PubMed

Kim, Byungsuk; Woo, Young-Ah

2018-05-30

In this study the authors developed a real-time Process Analytical Technology (PAT) of a coating process by applying in-line Raman spectroscopy to evaluate the coating weight gain, which is a quantitative analysis of the film coating layer. The wide area illumination (WAI) Raman probe was connected to the pan coater for real-time monitoring of changes in the weight gain of coating layers. Under the proposed in-line Raman scheme, a non-contact, non-destructive analysis was performed using WAI Raman probes with a spot size of 6 mm. The in-line Raman probe maintained a focal length of 250 mm, and a compressed air line was designed to protect the lens surface from spray droplets. The Design of Experiment (DOE) was applied to identify factors affecting the Raman spectra background of laser irradiation. The factors selected for DOE were the strength of compressed air connected to the probe, and the shielding of light by the transparent door connecting the probe to the pan coater. To develop a quantitative model, partial least squares (PLS) models as multivariate calibration were developed based on the three regions showing the specificity of TiO 2 individually or in combination. For the three single peaks (636 cm -1 , 512 cm -1 , 398 cm -1 ), least squares method (LSM) was applied to develop three univariate quantitative analysis models. One of best multivariate quantitative model having a factor of 1 gave the lowest RMSEP of 0.128, 0.129, and 0.125, respectively for prediction batches. When LSM was applied to the single peak at 636 cm -1 , the univariate quantitative model with an R 2 of 0.9863, slope of 0.5851, and y-intercept of 0.8066 had the lowest RMSEP of 0.138, 0.144, and 0.153, respectively for prediction batches. The in-line Raman spectroscopic method for the analysis of coating weight gain was verified by considering system suitability and parameters such as specificity, range, linearity, accuracy, and precision in accordance with ICH Q2 regarding method validation. The proposed in-line Raman spectroscopy can be utilized as a PAT for product quality assurance as it offers real-time monitoring of quantitative changes in coating weight gain and process end-points during the film coating process. Copyright © 2018 Elsevier B.V. All rights reserved.

Color representation and interpretation of special effect coatings.

PubMed

Ferrero, A; Perales, E; Rabal, A M; Campos, J; Martínez-Verdú, F M; Chorro, E; Pons, A

2014-02-01

A representation of the color gamut of special effect coatings is proposed and shown for six different samples, whose colors were calculated from spectral bidirectional reflectance distribution function (BRDF) measurements at different geometries. The most important characteristic of the proposed representation is that it allows a straightforward understanding of the color shift to be done both in terms of conventional irradiation and viewing angles and in terms of flake-based parameters. A different line was proposed to assess the color shift of special effect coatings on a*,b*-diagrams: the absorption line. Similar to interference and aspecular lines (constant aspecular and irradiation angles, respectively), an absorption line is the locus of calculated color coordinates from measurement geometries with a fixed bistatic angle. The advantages of using the absorption lines to characterize the contributions to the spectral BRDF of the scattering at the absorption pigments and the reflection at interference pigments for different geometries are shown.

The Zel'dovich approximation: key to understanding cosmic web complexity

NASA Astrophysics Data System (ADS)

Hidding, Johan; Shandarin, Sergei F.; van de Weygaert, Rien

2014-02-01

We describe how the dynamics of cosmic structure formation defines the intricate geometric structure of the spine of the cosmic web. The Zel'dovich approximation is used to model the backbone of the cosmic web in terms of its singularity structure. The description by Arnold et al. in terms of catastrophe theory forms the basis of our analysis. This two-dimensional analysis involves a profound assessment of the Lagrangian and Eulerian projections of the gravitationally evolving four-dimensional phase-space manifold. It involves the identification of the complete family of singularity classes, and the corresponding caustics that we see emerging as structure in Eulerian space evolves. In particular, as it is instrumental in outlining the spatial network of the cosmic web, we investigate the nature of spatial connections between these singularities. The major finding of our study is that all singularities are located on a set of lines in Lagrangian space. All dynamical processes related to the caustics are concentrated near these lines. We demonstrate and discuss extensively how all 2D singularities are to be found on these lines. When mapping this spatial pattern of lines to Eulerian space, we find a growing connectedness between initially disjoint lines, resulting in a percolating network. In other words, the lines form the blueprint for the global geometric evolution of the cosmic web.

Solvent-resistant sol-gel polydimethyldiphenylsiloxane coating for on-line hyphenation of capillary microextraction with high-performance liquid chromatography.

PubMed

Segro, Scott S; Malik, Abdul

2008-09-26

A sol-gel polydimethyldiphenylsiloxane (PDMDPS) coating was developed for capillary microextraction on-line hyphenated with high-performance liquid chromatography (HPLC). This coating was created using methyltrimethoxysilane (MTMS) as the sol-gel precursor and di-hydroxy-terminated PDMDPS as the sol-gel active polymer. The methyl and phenyl groups on the sol-gel active polymer and the methyl groups on the sol-gel precursor ultimately turned into pendant groups providing the ability to extract non-polar analytes. A 40-cm segment of 0.25 mm I.D. fused silica capillary containing the sol-gel PDMDPS coating was installed as an external sampling loop in an HPLC injection port. Aqueous samples containing polycyclic aromatic hydrocarbons (PAHs), aromatic compounds, ketones, and aldehydes were passed through this capillary wherein the analytes were extracted by the sol-gel coating. The extracted analytes were then transferred to the HPLC column using isocratic or gradient elution with an acetonitrile/water mobile phase. This capillary demonstrated excellent extraction capability for non-polar (e.g., polycyclic aromatic hydrocarbons and aromatic compounds) as well as moderately polar compounds, such as aromatic amines, ketones, and aldehydes. The test results indicate that PDMDPS can be successfully immobilized into a sol-gel network and that the resulting solvent-resistant sol-gel organic-inorganic hybrid coating can be effectively used for on-line hyphenation of capillary microextraction with high-performance liquid chromatography. The test results also indicate that the sol-gel PDMDPS coated capillary is resistant to high-temperature solvents, making it suitable for applications in high-temperature HPLC. To the best of our knowledge, this is the first report on the creation of a silica-based sol-gel PDMDPS coating used in capillary microextraction on-line hyphenated to HPLC.

Section BB Hatch Coating; Framing Plan on Line C Lodging ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Section B-B Hatch Coating; Framing Plan on Line C Lodging Knees at Hatch; Elevation A-A Hull Framing; Section at Hatch Frame 36, Starboard Looking Aft; Midship Section Frame 37, Port Looking Aft - Steam Schooner WAPAMA, Kaiser Shipyard No. 3 (Shoal Point), Richmond, Contra Costa County, CA

[The influence of immobilized fibronectin on karyotypic variability of two rat kangaroo kidney cell lines].

PubMed

Polianskaia, G G; Goriachaia, T S; Pinaev, G P

2007-01-01

The numerical and structural karyotypic variability has been investigated in "markerless" Rat kangaroo kidney cell lines NBL-3-17 and NBL-3-11 when cultivating on a fibronectin-coated surface. In cell line NBL-3-17, cultivated on the fibronectin-coated surface for 1, 2, 4 and 8 days, the character of cell distribution for the chromosome number has changed. These changes involve a significant decrease in frequency of cells with modal number of chromosomes, and an increase in frequency of cells with lower chromosomal number. Many new additional structural variants of the karyotype (SVK) appear. The observed alterations seem to be due preference adhesion of cells with lower chromosome number, disturbances of mitotic apparatus and selection of SVK, which are more adopted to changes in culture conditions. Detachment of cells from the fibronectin-coated surface, followed by 5 days cultivation on a hydrophilic surface restored control distribution. In cell line NBL-3-11, cultivated on the fibronectin-coated surface for 1, 2, 4 and 8 days, the character of numerical karyotypic variability did not change compared to control variants. In cell line NBL-3-17 the frequency of chromosomal aberrations under cultivation on the fibronectin-coated surface for 1, 2, 4 and 8 days did not change relative to control variants. In cell line NBL-3-11 the frequency of chromosomal aberrations under the same conditions significantly increases, mainly at the expence of chromosomal, chromatid breaks and dicentrics (telomeric association) relative to control variants. We discuss possible reasons of differences in the character of numerical and structural karyotypic variability between cell lines NBL-3-17 (hypotriploid) and NBL-3-11 (hypodiploid) under cultivation on fibronectin. The reasons of the observed interline karyotypic differences possibly consist in peculiarity of karyotypic structure of cell line NBL-3-11 and in the change of gene expression, namely in a dose of certain functioning genes in the hypotryploid cell line NBL-3-17.

40 CFR 52.1100 - Original identification of plan section.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Coating, Interior Sheet Drum Lining). (i) Incorporation by reference. (A) Revisions to COMAR 10.18.21.10... paper and plastic parts coating, including definitions for the terms fountain, letterpress printing... coating, and the addition of definitions for the terms sheet-fed paper coating and ultraviolet curable...

Integrated Glass Coating Manufacturing Line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brophy, Brenor

2015-09-30

This project aims to enable US module manufacturers to coat glass with Enki’s state of the art tunable functionalized AR coatings at the lowest possible cost and highest possible performance by encapsulating Enki’s coating process in an integrated tool that facilitates effective process improvement through metrology and data analysis for greater quality and performance while reducing footprint, operating and capital costs. The Phase 1 objective was a fully designed manufacturing line, including fully specified equipment ready for issue of purchase requisitions; a detailed economic justification based on market prices at the end of Phase 1 and projected manufacturing costs andmore » a detailed deployment plan for the equipment.« less

40 CFR 60.491 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the exterior of a two-piece beverage can body. The exterior base coat provides corrosion resistance... surface coating line used to apply a coating to the interior of a two-piece beverage can body. This coating provides a protective film between the contents of the beverage can and the metal can body. The...

40 CFR 60.491 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the exterior of a two-piece beverage can body. The exterior base coat provides corrosion resistance... surface coating line used to apply a coating to the interior of a two-piece beverage can body. This coating provides a protective film between the contents of the beverage can and the metal can body. The...

40 CFR 60.491 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the exterior of a two-piece beverage can body. The exterior base coat provides corrosion resistance... surface coating line used to apply a coating to the interior of a two-piece beverage can body. This coating provides a protective film between the contents of the beverage can and the metal can body. The...

40 CFR 60.491 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the exterior of a two-piece beverage can body. The exterior base coat provides corrosion resistance... surface coating line used to apply a coating to the interior of a two-piece beverage can body. This coating provides a protective film between the contents of the beverage can and the metal can body. The...

Impact-Resistant Ceramic Coating

NASA Technical Reports Server (NTRS)

Wheeler, W. H.; Creedon, J. F.; Izu, Y. D.

1986-01-01

Refractory fibers more than double strength of coating. Impact strengths of ceramic coatings increase with increasing whisker content. Silicon carbide whiskers clearly produce largest increase, and improvement grows even more with high-temperature sintering. Coating also improves thermal and mechanical properties of electromagnetic components, mirrors, furnace linings, and ceramic parts of advanced internal-combustion engines.

Taming contact line instability for pattern formation

PubMed Central

Deblais, A.; Harich, R.; Colin, A.; Kellay, H.

2016-01-01

Coating surfaces with different fluids is prone to instability producing inhomogeneous films and patterns. The contact line between the coating fluid and the surface to be coated is host to different instabilities, limiting the use of a variety of coating techniques. Here we take advantage of the instability of a receding contact line towards cusp and droplet formation to produce linear patterns of variable spacings. We stabilize the instability of the cusps towards droplet formation by using polymer solutions that inhibit this secondary instability and give rise to long slender cylindrical filaments. We vary the speed of deposition to change the spacing between these filaments. The combination of the two gives rise to linear patterns into which different colloidal particles can be embedded, long DNA molecules can be stretched and particles filtered by size. The technique is therefore suitable to prepare anisotropic structures with variable properties. PMID:27506626

Taming contact line instability for pattern formation.

PubMed

Deblais, A; Harich, R; Colin, A; Kellay, H

2016-08-10

Coating surfaces with different fluids is prone to instability producing inhomogeneous films and patterns. The contact line between the coating fluid and the surface to be coated is host to different instabilities, limiting the use of a variety of coating techniques. Here we take advantage of the instability of a receding contact line towards cusp and droplet formation to produce linear patterns of variable spacings. We stabilize the instability of the cusps towards droplet formation by using polymer solutions that inhibit this secondary instability and give rise to long slender cylindrical filaments. We vary the speed of deposition to change the spacing between these filaments. The combination of the two gives rise to linear patterns into which different colloidal particles can be embedded, long DNA molecules can be stretched and particles filtered by size. The technique is therefore suitable to prepare anisotropic structures with variable properties.

75 FR 19252 - Delegation of New Source Performance Standards and National Emission Standards for Hazardous Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

... Industrial Process Cooling X Towers. R Gasoline Distribution X S Pulp & Paper MACT I X T Halogenated Solvent.... IIII Auto & Light Duty Truck (Surface X Coating). JJJJ Paper & Other Webs (Surface X Coating). KKKK... subparts B, H, I, K, Q, R, T, and W. For the part 63 NESHAPs, this includes the NESHAPs set forth in the...

75 FR 67625 - Delegation of National Emission Standards for Hazardous Air Pollutants for Source Categories...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... Paper X X T Halogenated Solvent X X X Cleaning. U Group I Polymers and Resins X X W Epoxy Resins... Trucks. JJJJ Paper and Other Web Coating X X KKKK Surface Coating of Metal X X Cans. MMMM Miscellaneous...,'' ``us,'' and ``our'' refer to EPA. Table of Contents I. Background A. Delegation of NESHAP B. Clark...

Ultra-High Efficiency / Low Hydrogen Embrittlement Nanostructured Zn-Based Electrodeposits as Environmentally Benign Cd-Replacement Coatings for High Strength Steel Fasteners

DTIC Science & Technology

2011-04-01

forma The prese corrosion coating) w conversio converted not develo before and a : Example un ted Zn-Ni ac : Example s Zn-Ni alkalin nt of scribing...Protection Agency, 1998. Retrieved from web July 30th 2009. Available online at www.epa.gov/ iris /subst/0141.htm. 3 M. Bielawski, Surface and

A-E Services to Perform a Cathodic Protection Survey of the Bulk Fuel Terminals at N.S.C. Pearl Harbor, Hawaii. Volume I.

DTIC Science & Technology

1982-06-01

20) From VC-D to VC-E a. 8" Avgas Line - Coated Steel (21) From FC -E to Victor Dock #1 a. 12" Avgas Line - Coated Steel (22) From Air Force Scraper...14. Bldg. S776 3" Ballast Line to VC-2 - 775 3" Ballast Line to Loading Rack - 775 15. 6" Water Line, 10’ N of Bldg. S776 - 745 6" AFFF Line, N of...S776 3" Ballast line to VC-2 - 740 - 775 35 3" Ballast line to Loading Rack - 740 - 775 35 15. 6" Water line 10’ N of Bldg. S776 - 710 - 745 35 6" AFFF

Wilson Lines and Webs in Higher-Order QCD

NASA Astrophysics Data System (ADS)

White, Chris D.

2018-03-01

Wilson lines have a number of uses in non-abelian gauge theories. A topical example in QCD is the description of radiation in the soft or collinear limit, which must often be resummed to all orders in perturbation theory. Correlators involving a pair of Wilson lines are known to exponentiate in terms of special Feynman diagrams called "webs". I will show how this language can be extended to an arbitrary number of Wilson lines, which introduces novel new combinatoric structures (web mixing matrices) of interest in their own right. I will also summarise recent results obtained from applying this formalism at three-loop order, before concluding with a list of open problems.

Augmenting MFL Tools with Sensors That Assess Coating Condition

DOT National Transportation Integrated Search

2009-03-16

External coatings are routinely used to protect transmission pipelines from corrosion; however, coatings may degrade or disbond over time enabling corrosion to occur. Transmission pipeline operators often use magnetic flux leakage (MFL) in-line inspe...

Low Contribution of PbO2-Coated Lead Service Lines to Water Lead Contamination at the Tap

EPA Science Inventory

To determine if field experience corroborates that formation of stable PbO2 coatings on lead service lines (LSLs) provides an effective lead contamination control strategy, lead profile sampling was undertaken at eight home kitchen taps in three US cities (Newport, Rhode Island; ...

Effect of sealer coating and storage methods on the surface roughness of soft liners.

PubMed

Usta Kutlu, Ilknur; Yanikoğlu, Nuran Dinckal; Kul, Esra; Duymuş, Zeynep Yesïl; Sağsöz, Nurdan Polat

2016-03-01

A soft lining is applied under a removable prosthesis for various reasons. The porosity of the lining material may increase colonization by microorganisms and cause tissue inflammation. The purpose of this in vitro study was to evaluate the effect of sealer coating on the surface roughness of soft lining materials under 4 different conditions. A total of 125 specimens were prepared. One high-temperature silicone-based soft lining material and 2 room-temperature-polymerized soft lining materials (1 silicone-based and 1 methacrylate-based) were used. Twenty-five specimens of each room-temperature soft lining material were coated with 2 layers of surface sealer. Additionally, 5 specimens of each material were stored in either distilled water, Coca-Cola, denture cleanser, saliva, or air. The surface roughness was measured at baseline and after 1, 7, 14, and 28 days. Surface roughness values were analyzed with repeated measures analysis of variance, and the Bonferroni multiple comparison test was performed using time-dependent groups and storage methods. In the time-dependent groups, methacrylate-based sealer-coated soft liners exhibited a significant increase in roughness (1.74-2.09 μm, P<.001), and silicone-based sealer-coated soft liners exhibited a decrease in roughness, but it was not significant (2.16-2.02 μm, P>.05). Therefore, the sealer coating was not effective in reducing surface roughness. Among the time-dependent storage methods, the denture cleanser exhibited an almost significant increase in roughness (1.83-1.99 μm, P=.054). Coca-Cola and artificial saliva did not show a significant difference (P>.05). However, a significant decrease in roughness was found with distilled water (P=.02) and air (P<.001). Statistically significant differences in surface roughness were found among the different types of soft liners. The sealer coating had no significant effect, and denture cleanser slightly increased the surface roughness. Contrary to expectations, the roughness did not increase in all groups over time. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

On-line defect detection of aluminum coating using fiber optic sensor

NASA Astrophysics Data System (ADS)

Patil, Supriya S.; Shaligram, A. D.

2015-03-01

Aluminum metallization using the sprayed coating for exhaust mild steel (MS) pipes of tractors is a standard practice for avoiding rusting. Patches of thin metal coats are prone to rusting and are thus considered as defects in the surface coating. This paper reports a novel configuration of the fiber optic sensor for on-line checking the aluminum metallization uniformity and hence for defect detection. An optimally chosen high bright 440 nm BLUE LED (light-emitting diode) launches light into a transmitting fiber inclined at the angle of 60° to the surface under inspection placed adequately. The reflected light is transported by a receiving fiber to a blue enhanced photo detector. The metallization thickness on the coated surface results in visually observable variation in the gray shades. The coated pipe is spirally inspected by a combination of linear and rotary motions. The sensor output is the signal conditioned and monitored with RISHUBH DAS. Experimental results show the good repeatability in the defect detection and coating non-uniformity measurement.

Microscopic analysis and simulation of check-mark stain on the galvanized steel strip

NASA Astrophysics Data System (ADS)

So, Hongyun; Yoon, Hyun Gi; Chung, Myung Kyoon

2010-11-01

When galvanized steel strip is produced through a continuous hot-dip galvanizing process, the thickness of adhered zinc film is controlled by plane impinging air gas jet referred to as "air-knife system". In such a gas-jet wiping process, stain of check-mark or sag line shape frequently appears. The check-mark defect is caused by non-uniform zinc coating and the oblique patterns such as "W", "V" or "X" on the coated surface. The present paper presents a cause and analysis of the check-mark formation and a numerical simulation of sag lines by using the numerical data produced by Large Eddy Simulation (LES) of the three-dimensional compressible turbulent flow field around the air-knife system. It was found that there is alternating plane-wise vortices near the impinging stagnation region and such alternating vortices move almost periodically to the right and to the left sides on the stagnation line due to the jet flow instability. Meanwhile, in order to simulate the check-mark formation, a novel perturbation model has been developed to predict the variation of coating thickness along the transverse direction. Finally, the three-dimensional zinc coating surface was obtained by the present perturbation model. It was found that the sag line formation is determined by the combination of the instantaneous coating thickness distribution along the transverse direction near the stagnation line and the feed speed of the steel strip.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, S. R.; Daniel, A.

The purpose of the Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC and Southwire Company was to jointly develop a low cost, commercially viable, water-repellant anti-icing coating system for high voltage transmission lines. Icing of power lines and other structures caused by freezing rain events occurs annually in the United States, and leads to severe and prolonged power outages. These outages cause untold economic and personal distress for many American families and businesses. Researchers at the Department of Energy?s Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee have previously developed a set of superhydrophobic coatings with remarkable anti-icingmore » properties that could potentially be sprayed or painted onto high-tension power lines and pylons. These coatings drastically reduce ice accumulation on these structures during freezing rain events. The project involved obtaining technical input, supplies and test high voltage cables from Southwire, along with the joint development of anti-icing coating techniques, which would result in a commercial license agreement between Southwire and ORNL, and potentially other companies requiring water repellent anti-icing coatings.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, Scott Robert

The purpose of the Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC and Southwire Company was to jointly develop a low cost, commercially viable, water-repellant anti-icing coating system for high voltage transmission lines. Icing of power lines and other structures caused by freezing rain events occurs annually in the United States, and leads to severe and prolonged power outages. These outages cause untold economic and personal distress for many American families and businesses. Researchers at the Department of Energy s Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee have previously developed a set of superhydrophobic coatings with remarkablemore » anti-icing properties that could potentially be sprayed or painted onto high-tension power lines and pylons. These coatings drastically reduce ice accumulation on these structures during freezing rain events. The project involved obtaining technical input, supplies and test high voltage cables from Southwire, along with the joint development of anti-icing coating techniques, which would result in a commercial license agreement between Southwire and ORNL, and potentially other companies requiring water repellent anti-icing coatings.« less

40 CFR 63.3350 - If I use a control device to comply with the emission standards, what monitoring must I do?

Code of Federal Regulations, 2010 CFR

2010-07-01

... must be certified by the manufacturer to be accurate to within ±2.0 percent by mass. (e) Continuous... Pollutants: Paper and Other Web Coating General Requirements for Compliance with the Emission Standards and... standards, what monitoring must I do? (a) A summary of monitoring you must do follows: If you operate a web...

40 CFR 63.3350 - If I use a control device to comply with the emission standards, what monitoring must I do?

Code of Federal Regulations, 2011 CFR

2011-07-01

... must be certified by the manufacturer to be accurate to within ±2.0 percent by mass. (e) Continuous... Pollutants: Paper and Other Web Coating General Requirements for Compliance with the Emission Standards and... standards, what monitoring must I do? (a) A summary of monitoring you must do follows: If you operate a web...

Noncontact conductivity and dielectric measurement for high throughput roll-to-roll nanomanufacturing

NASA Astrophysics Data System (ADS)

Orloff, Nathan D.; Long, Christian J.; Obrzut, Jan; Maillaud, Laurent; Mirri, Francesca; Kole, Thomas P.; McMichael, Robert D.; Pasquali, Matteo; Stranick, Stephan J.; Alexander Liddle, J.

2015-11-01

Advances in roll-to-roll processing of graphene and carbon nanotubes have at last led to the continuous production of high-quality coatings and filaments, ushering in a wave of applications for flexible and wearable electronics, woven fabrics, and wires. These applications often require specific electrical properties, and hence precise control over material micro- and nanostructure. While such control can be achieved, in principle, by closed-loop processing methods, there are relatively few noncontact and nondestructive options for quantifying the electrical properties of materials on a moving web at the speed required in modern nanomanufacturing. Here, we demonstrate a noncontact microwave method for measuring the dielectric constant and conductivity (or geometry for samples of known dielectric properties) of materials in a millisecond. Such measurement times are compatible with current and future industrial needs, enabling real-time materials characterization and in-line control of processing variables without disrupting production.

Noncontact conductivity and dielectric measurement for high throughput roll-to-roll nanomanufacturing

PubMed Central

Orloff, Nathan D.; Long, Christian J.; Obrzut, Jan; Maillaud, Laurent; Mirri, Francesca; Kole, Thomas P.; McMichael, Robert D.; Pasquali, Matteo; Stranick, Stephan J.; Alexander Liddle, J.

2015-01-01

Advances in roll-to-roll processing of graphene and carbon nanotubes have at last led to the continuous production of high-quality coatings and filaments, ushering in a wave of applications for flexible and wearable electronics, woven fabrics, and wires. These applications often require specific electrical properties, and hence precise control over material micro- and nanostructure. While such control can be achieved, in principle, by closed-loop processing methods, there are relatively few noncontact and nondestructive options for quantifying the electrical properties of materials on a moving web at the speed required in modern nanomanufacturing. Here, we demonstrate a noncontact microwave method for measuring the dielectric constant and conductivity (or geometry for samples of known dielectric properties) of materials in a millisecond. Such measurement times are compatible with current and future industrial needs, enabling real-time materials characterization and in-line control of processing variables without disrupting production. PMID:26592441

Mediterranean report/heated pipeline offloads tankers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-08-01

The first heated submarine pipeline in Europe, according to Anonima Petroli Italiana, is now in operation from their Falconara Refinery near Ancona, Italy, to an existing offshore loading facility. The 3850 m long, 24 inch wide line, laid on the seabottom at 3-14 m depths, was built to offload high pour/high viscosity crudes requiring a minimum constant discharge temperature of 45-65 C. Four 3.5 mm heating pipes (three operating and one spare) were stretch-welded to the outside of the line at 45 degree angles to each other; they are heated at about 100 m/m by a parasitic current formed onmore » the pipe while 1500 volt current is passed through a cable inside the pipe. The heating system is equipped with an electric feeding installation, automatic power regulation, and remote sensors applied along the sea line. The heating pipes were protected with a coat of epoxy tar paint, a 50 mm thick and 70 kg/cm dense sprayed-on urethane foam coat, a sheath of butyric elastomer covered with an adhering 3 mm coat of polyethylene, and a concrete coat for protection and weighting. Specially designed water stops were placed at both ends of every line section under the waterproofing. Industria Construzioni Opere Publiche prefabricated the line on shore and laid it from shore.« less

Polyphenol oxidase activity and differential accumulation of polyphenolics in seed coats of pinto bean (Phaseolus vulgaris L.) characterize postharvest color changes.

PubMed

Marles, M A Susan; Vandenberg, Albert; Bett, Kirstin E

2008-08-27

Postharvest darkening of pinto bean (Phaseolus vulgaris L.) was evaluated in a population of recombinant inbred lines derived from a cross between CDC Pintium (a regular-darkening line) and 1533-15 (a slow-darkening line). Flavonoid metabolite concentrations, polyphenol oxidase activity, lignin concentration, and seed coat anatomy characteristics were assessed for cosegregation with the darkening phenotype. Significantly lower kaempferol concentrations (p = 0.00001) together with differences in polyphenol oxidase activity (p = 0.0045) were two of the key findings associated with these recombinant inbred lines. In addition, two different assays (thioglycolic acid and Klason lignin) to quantify lignin together with an assessment of extractable condensed tannin were used to estimate the contribution of these polymers to changes in the seed coat tissue. This is the first report of precise biochemical characterization of polyphenolics that associate with postharvest darkening in legumes.

7 CFR 51.2763 - Damage.

Code of Federal Regulations, 2010 CFR

2010-01-01

... cuts, web or frass; (d) Freezing injury causing hard, translucent or discolored flesh; and, (e) Dirt when the surface of the kernel is heavily smeared, thickly flecked or coated with dirt, seriously...

Quantifying Pharmaceutical Film Coating with Optical Coherence Tomography and Terahertz Pulsed Imaging: An Evaluation.

PubMed

Lin, Hungyen; Dong, Yue; Shen, Yaochun; Zeitler, J Axel

2015-10-01

Spectral domain optical coherence tomography (OCT) has recently attracted a lot of interest in the pharmaceutical industry as a fast and non-destructive modality for quantification of thin film coatings that cannot easily be resolved with other techniques. Because of the relative infancy of this technique, much of the research to date has focused on developing the in-line measurement technique for assessing film coating thickness. To better assess OCT for pharmaceutical coating quantification, this paper evaluates tablets with a range of film coating thickness measured using OCT and terahertz pulsed imaging (TPI) in an off-line setting. In order to facilitate automated coating quantification for film coating thickness in the range of 30-200 μm, an algorithm that uses wavelet denoising and a tailored peak finding method is proposed to analyse each of the acquired A-scan. Results obtained from running the algorithm reveal an increasing disparity between the TPI and OCT measured intra-tablet variability when film coating thickness exceeds 100 μm. The finding further confirms that OCT is a suitable modality for characterising pharmaceutical dosage forms with thin film coatings, whereas TPI is well suited for thick coatings. © 2015 The Authors. Journal of Pharmaceutical Sciences published by Wiley Periodicals, Inc. and the American Pharmacists Association.

7 CFR 51.2721 - Damage.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., web or frass; (d) Freezing injury causing hard, translucent or discolored flesh; and (e) Dirt when the surface of the kernel is heavily smeared, thickly flecked or coated with dirt, seriously affecting its...

High Resolution Quantitative Microbeam Analysis of Ir-coated Geological Specimens Using Conventionally Coated Standards

NASA Astrophysics Data System (ADS)

Armstrong, J. T.; Crispin, K. L.

2012-12-01

Traditionally, quantitative electron microbeam analyses of insulating specimens are performed after coating the materials with thin conducting layers of carbon. For x-ray lines greater than 1 keV in energy and beam voltages in excess of 10 keV, the results are insensitive to the exact thickness of the carbon coat. High resolution imaging, low voltage analysis, and analysis of specimens containing low levels of carbon require the use of substitute conductive coats. Typical substitutes for carbon coats (e.g., Au, Au-Pd, Cr, Al) require either using similarly coated standards or substantial corrections to be applied. Even when using modern multi-layer correction algorithms or Monte Carlo calculations, significant errors can result (e.g., Armstrong 2009, Armstrong and Crispin, 2012). We propose the use of ultra-thin layers of Ir as a substitute for C in the analysis of insulating geological specimens. Ir has been found to be an excellent coating material for high resolution imaging (e.g., Echlin, 2009). Sputtered layers as thin as 0.5 nm are found to be conductive, and layers of just a few nm provide good protection against beam damage with sub-nm grain size (Sebring et al., 1999). We have analyzed a series of geological materials with Ir coats between 1 - 8 nm and found similar levels of effects on emitted x-ray intensities as produced with typical carbon coat thicknesses (10-25 nm). E.g., for Ir thicknesses less than 5 nm, the reduction of intensity for x-ray lines between 1 and 7 keV are between 1-3% for a beam energy of 15 keV. The reduction in intensity for higher-energy lines such as Fe-K is actually less than produced by typical C-coats. We will present the results of these experiments and propose simple algorithmic equations which fit these data.

40 CFR 63.5880 - How do I determine how much neat resin plus is applied to the line and how much neat gel coat...

Code of Federal Regulations, 2010 CFR

2010-07-01

... SOURCE CATEGORIES National Emissions Standards for Hazardous Air Pollutants: Reinforced Plastic... gel coat plus is applied to the line each year. (a) Track formula usage by end product/thickness combinations. (b) Use in-house records to show usage. This may be either from automated systems or manual...

Optical Coatings With Graded Index Layers For High Power Laser Applications: Design

NASA Astrophysics Data System (ADS)

Zukic, Muamer; Guenther, Karl H.

1988-06-01

Graded index layers provide a greater flexibility for the design of optical coatings than "homogeneous" layers. A graded index layer can replace the whole or a part of a traditional multilayer stack of alternating thin films of high and low refractive index. This paper presents design examples for broadband antireflection coatings, narrowband high reflectors (also referred to as minus filters or rejection line filters), and non-polarizing beam splitters. Optimized refractive index profiles are derived for broadband antireflection coatings for various combinations of incident medium and substrate. The rejection line filter example uses a sinusoidal (rugate) index profile. The non-polarizing beamsplitter summarizes the topical contents of a paper presented in another conference at the same symposium.

On-line tritium production monitor

DOEpatents

Mihalczo, John T.

1993-01-01

A scintillation optical fiber system for the on-line monitoring of nuclear reactions in an event-by-event manner is described. In the measurement of tritium production one or more optical fibers are coated with enriched .sup.6 Li and connected to standard scintillation counter circuitry. A neutron generated .sup.6 Li(n )T reaction occurs in the coated surface of .sup.6 Li-coated fiber to produce energetic alpha and triton particles one of which enters the optical fiber and scintillates light through the fiber to the counting circuit. The coated optical fibers can be provided with position sensitivity by placing a mirror at the free end of the fibers or by using pulse counting circuits at both ends of the fibers.

On-line tritium production monitor

DOEpatents

Mihalczo, J.T.

1993-11-23

A scintillation optical fiber system for the on-line monitoring of nuclear reactions in an event-by-event manner is described. In the measurement of tritium production one or more optical fibers are coated with enriched {sup 6}Li and connected to standard scintillation counter circuitry. A neutron generated {sup 6}Li(n)T reaction occurs in the coated surface of {sup 6}Li-coated fiber to produce energetic alpha and triton particles one of which enters the optical fiber and scintillates light through the fiber to the counting circuit. The coated optical fibers can be provided with position sensitivity by placing a mirror at the free end of the fibers or by using pulse counting circuits at both ends of the fibers. 5 figures.

Evaluation of in-line Raman data for end-point determination of a coating process: Comparison of Science-Based Calibration, PLS-regression and univariate data analysis.

PubMed

Barimani, Shirin; Kleinebudde, Peter

2017-10-01

A multivariate analysis method, Science-Based Calibration (SBC), was used for the first time for endpoint determination of a tablet coating process using Raman data. Two types of tablet cores, placebo and caffeine cores, received a coating suspension comprising a polyvinyl alcohol-polyethylene glycol graft-copolymer and titanium dioxide to a maximum coating thickness of 80µm. Raman spectroscopy was used as in-line PAT tool. The spectra were acquired every minute and correlated to the amount of applied aqueous coating suspension. SBC was compared to another well-known multivariate analysis method, Partial Least Squares-regression (PLS) and a simpler approach, Univariate Data Analysis (UVDA). All developed calibration models had coefficient of determination values (R 2 ) higher than 0.99. The coating endpoints could be predicted with root mean square errors (RMSEP) less than 3.1% of the applied coating suspensions. Compared to PLS and UVDA, SBC proved to be an alternative multivariate calibration method with high predictive power. Copyright © 2017 Elsevier B.V. All rights reserved.

77 FR 14279 - National Volatile Organic Compound Emission Standards for Aerosol Coatings-Addition of Dimethyl...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-09

... revises Table 1 of the final rule by moving the units, expressed as grams of ozone per gram of product (g... 2A, 2B, and 2C by adding units, expressed as grams of ozone per gram of VOC (g O 3 /g VOC), to the... Webbing/Veiling Coatings WFC 0.85 Weld-Through Primers WTP 1.00 Wood Stains WSP 1.40 [[Page 14284

Development and in-line validation of a Process Analytical Technology to facilitate the scale up of coating processes.

PubMed

Wirges, M; Funke, A; Serno, P; Knop, K; Kleinebudde, P

2013-05-05

Incorporation of an active pharmaceutical ingredient (API) into the coating layer of film-coated tablets is a method mainly used to formulate fixed-dose combinations. Uniform and precise spray-coating of an API represents a substantial challenge, which could be overcome by applying Raman spectroscopy as process analytical tool. In pharmaceutical industry, Raman spectroscopy is still mainly used as a bench top laboratory analytical method and usually not implemented in the production process. Concerning the application in the production process, a lot of scientific approaches stop at the level of feasibility studies and do not manage the step to production scale and process applications. The present work puts the scale up of an active coating process into focus, which is a step of highest importance during the pharmaceutical development. Active coating experiments were performed at lab and production scale. Using partial least squares (PLS), a multivariate model was constructed by correlating in-line measured Raman spectral data with the coated amount of API. By transferring this model, being implemented for a lab scale process, to a production scale process, the robustness of this analytical method and thus its applicability as a Process Analytical Technology (PAT) tool for the correct endpoint determination in pharmaceutical manufacturing could be shown. Finally, this method was validated according to the European Medicine Agency (EMA) guideline with respect to the special requirements of the applied in-line model development strategy. Copyright © 2013 Elsevier B.V. All rights reserved.

The WEB 2.0 induced paradigm shift in the e-learning and the role of crowdsourcing in dental education.

PubMed

Thurzo, A; Stanko, P; Urbanova, W; Lysy, J; Suchancova, B; Makovnik, M; Javorka, V

2010-01-01

Authors evaluated the effect of the WEB 2.0 environment on dental education and estimated the difference in retention of knowledge by cephalometric analysis in orthodontics between conventional education and off-line e-learning. Five years of experience with complex web-based e-learning system allowed the evaluation by retrospective analysis and on-line questionnaire. The results revealed the current trends in on-line behavior of students based on the WEB 2.0 innovative technologies like Ajax. Results confirmed an increasing number of resources with a rising frequency of e-learning materials. The study confirmed that e-learning of the same subject is more efficient in immediate examination after the lecture with even better results after 12 and 24 months against the control group (Tab. 3, Fig. 1, Ref. 26).

Development of Process Analytical Technology (PAT) methods for controlled release pellet coating.

PubMed

Avalle, P; Pollitt, M J; Bradley, K; Cooper, B; Pearce, G; Djemai, A; Fitzpatrick, S

2014-07-01

This work focused on the control of the manufacturing process for a controlled release (CR) pellet product, within a Quality by Design (QbD) framework. The manufacturing process was Wurster coating: firstly layering active pharmaceutical ingredient (API) onto sugar pellet cores and secondly a controlled release (CR) coating. For each of these two steps, development of a Process Analytical Technology (PAT) method is discussed and also a novel application of automated microscopy as the reference method. Ultimately, PAT methods should link to product performance and the two key Critical Quality Attributes (CQAs) for this CR product are assay and release rate, linked to the API and CR coating steps respectively. In this work, the link between near infra-red (NIR) spectra and those attributes was explored by chemometrics over the course of the coating process in a pilot scale industrial environment. Correlations were built between the NIR spectra and coating weight (for API amount), CR coating thickness and dissolution performance. These correlations allow the coating process to be monitored at-line and so better control of the product performance in line with QbD requirements. Copyright © 2014 Elsevier B.V. All rights reserved.

Vapor deposition on doublet airfoil substrates: Control of coating thickness and microstructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodgers, Theron M.; Zhao, Hengbei; Wadley, Haydn N. G., E-mail: haydn@virginia.edu

Gas jet assisted vapor deposition processes for depositing coatings are conducted at higher pressures than conventional physical vapor deposition methods, and have shown promise for coating complex shaped substrates including those with non-line-of-sight (NLS) regions on their surface. These regions typically receive vapor atoms at a lower rate and with a wider incident angular distribution than substrate regions in line-of-sight (LS) of the vapor source. To investigate the coating of such substrates, the thickness and microstructure variation along the inner (curved) surfaces of a model doublet airfoil containing both LS and NLS regions has been investigated. Results from atomistic simulationsmore » and experiments confirm that the coating's thickness is thinner in flux-shadowed regions than in other regions for all the coating processes investigated. They also indicated that the coatings columnar microstructure and pore volume fraction vary with surface location through the LS to NLS transition zone. A substrate rotation strategy for optimizing the thickness over the entire doublet airfoil surface was investigated, and led to the identification of a process that resulted in only small variation of coating thickness, columnar growth angle, and pore volume fraction on all doublet airfoil surfaces.« less

Punctuated evolution of viscid silk in spider orb webs supported by mechanical behavior of wet cribellate silk

NASA Astrophysics Data System (ADS)

Piorkowski, Dakota; Blackledge, Todd A.

2017-08-01

The origin of viscid capture silk in orb webs, from cribellate silk-spinning ancestors, is a key innovation correlated with significant diversification of web-building spiders. Ancestral cribellate silk consists of dry nanofibrils surrounding a stiff, axial fiber that adheres to prey through van der Waals interactions, capillary forces, and physical entanglement. In contrast, viscid silk uses chemically adhesive aqueous glue coated onto a highly compliant and extensible flagelliform core silk. The extensibility of the flagelliform fiber accounts for half of the total work of adhesion for viscid silk and is enabled by water in the aqueous coating. Recent cDNA libraries revealed the expression of flagelliform silk proteins in cribellate orb-weaving spiders. We hypothesized that the presence of flagelliform proteins in cribellate silk could have allowed for a gradual shift in mechanical performance of cribellate axial silk, whose effect was masked by the dry nature of its adhesive. We measured supercontraction and mechanical performance of cribellate axial silk, in wet and dry states, for two species of cribellate orb web-weaving spiders to see if water enabled flagelliform silk-like performance. We found that compliance and extensibility of wet cribellate silk increased compared to dry state as expected. However, when compared to other silk types, the response to water was more similar to other web silks, like major and minor ampullate silk, than to viscid silk. These findings support the punctuated evolution of viscid silk mechanical performance.

Methods for making deposited films with improved microstructures

DOEpatents

Patten, James W.; Moss, Ronald W.; McClanahan, Edwin D.

1982-01-01

Methods for improving microstructures of line-of-sight deposited films are described. Columnar growth defects ordinarily produced by geometrical shadowing during deposition of such films are eliminated without resorting to post-deposition thermal or mechanical treatments. The native, as-deposited coating qualities, including homogeneity, fine grain size, and high coating-to-substrate adherence, can thus be retained. The preferred method includes the steps of emitting material from a source toward a substrate to deposit a coating non-uniformly on the substrate surface, removing a portion of the coating uniformly over the surface, again depositing material onto the surface, but from a different direction, and repeating the foregoing steps. The quality of line-of-sight deposited films such as those produced by sputtering, progressively deteriorates as the angle of incidence between the flux and the surface becomes increasingly acute. Depositing non-uniformly, so that the coating becomes progressively thinner as quality deteriorates, followed by uniformly removing some of the coating, such as by resputtering, eliminates the poor quality portions, leaving only high quality portions of the coating. Subsequently sputtering from a different direction applies a high quality coating to other regions of the surface. Such steps can be performed either simultaneously or sequentially to apply coatings of a uniformly high quality, closed microstructure to three-dimensional or larger planar surfaces.

Deposited films with improved microstructures

DOEpatents

Patten, James W.; Moss, Ronald W.; McClanahan, Edwin D.

1984-01-01

Methods for improving microstructures of line-of-sight deposited films are described. Columnar growth defects ordinarily produced by geometrical shadowing during deposition of such films are eliminated without resorting to post-deposition thermal or mechanical treatments. The native, as-deposited coating qualities, including homogeneity, fine grain size, and high coating-to-substrate adherence, can thus be retained. The preferred method includes the steps of emitting material from a source toward a substrate to deposit a coating non-uniformly on the substrate surface, removing a portion of the coating uniformly over the surface, again depositing material onto the surface, but from a different direction, and repeating the foregoing steps. The quality of line-of-sight deposited films such as those produced by sputtering, progressively deteriorates as the angle of incidence between the flux and the surface becomes increasingly acute. Depositing non-uniformly, so that the coating becomes progressively thinner as quality deteriorates, followed by uniformly removing some of the coating, such as by resputtering, eliminates the poor quality portions, leaving only high quality portions of the coating. Subsequently sputtering from a different direction applies a high quality coating to other regions of the surface. Such steps can be performed either simultaneously or sequentially to apply coatings of a uniformly high quality, closed microstructure to three-dimensional or large planar surfaces.

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

Quantifying Pharmaceutical Film Coating with Optical Coherence Tomography and Terahertz Pulsed Imaging: An Evaluation

PubMed Central

Lin, Hungyen; Dong, Yue; Shen, Yaochun; Zeitler, J Axel

2015-01-01

Spectral domain optical coherence tomography (OCT) has recently attracted a lot of interest in the pharmaceutical industry as a fast and non-destructive modality for quantification of thin film coatings that cannot easily be resolved with other techniques. Because of the relative infancy of this technique, much of the research to date has focused on developing the in-line measurement technique for assessing film coating thickness. To better assess OCT for pharmaceutical coating quantification, this paper evaluates tablets with a range of film coating thickness measured using OCT and terahertz pulsed imaging (TPI) in an off-line setting. In order to facilitate automated coating quantification for film coating thickness in the range of 30–200 μm, an algorithm that uses wavelet denoising and a tailored peak finding method is proposed to analyse each of the acquired A-scan. Results obtained from running the algorithm reveal an increasing disparity between the TPI and OCT measured intra-tablet variability when film coating thickness exceeds 100 μm. The finding further confirms that OCT is a suitable modality for characterising pharmaceutical dosage forms with thin film coatings, whereas TPI is well suited for thick coatings. © 2015 The Authors. Journal of Pharmaceutical Sciences published by Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci 104:3377–3385, 2015 PMID:26284354

Quantifying Pharmaceutical Film Coating with Optical Coherence Tomography and Terahertz Pulsed Imaging: An Evaluation.

PubMed

Lin, Hungyen; Dong, Yue; Shen, Yaochun; Axel Zeitler, J

2015-10-01

Spectral domain optical coherence tomography (OCT) has recently attracted a lot of interest in the pharmaceutical industry as a fast and non-destructive modality for quantification of thin film coatings that cannot easily be resolved with other techniques. Because of the relative infancy of this technique, much of the research to date has focused on developing the in-line measurement technique for assessing film coating thickness. To better assess OCT for pharmaceutical coating quantification, this paper evaluates tablets with a range of film coating thickness measured using OCT and terahertz pulsed imaging (TPI) in an off-line setting. In order to facilitate automated coating quantification for film coating thickness in the range of 30-200μm, an algorithm that uses wavelet denoising and a tailored peak finding method is proposed to analyse each of the acquired A-scan. Results obtained from running the algorithm reveal an increasing disparity between the TPI and OCT measured intra-tablet variability when film coating thickness exceeds 100μm. The finding further confirms that OCT is a suitable modality for characterising pharmaceutical dosage forms with thin film coatings, whereas TPI is well suited for thick coatings. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci 104:3377-3385, 2015. Copyright © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

ICI optical data storage tape

NASA Technical Reports Server (NTRS)

Mclean, Robert A.; Duffy, Joseph F.

1992-01-01

Optical data storage tape is now a commercial reality. The world's first successful development of a digital optical tape system is complete. This is based on the Creo 1003 optical tape recorder with ICI 1012 write-once optical tape media. Flexible optical media offers many benefits in terms of manufacture; for a given capital investment, continuous, web-coating techniques produce more square meters of media than batch coating. The coated layers consist of a backcoat on the non-active side; on the active side there is a subbing layer, then reflector, dye/polymer, and transparent protective overcoat. All these layers have been tailored for ease of manufacture and specific functional characteristics.

Optical coherence tomography for non-destructive analysis of coatings in pharmaceutical tablets

NASA Astrophysics Data System (ADS)

Markl, Daniel; Hannesschläger, Günther; Sacher, Stephan; Khinast, Johannes G.; Leitner, Michael

2013-04-01

Tablet coating is a common pharmaceutical technique to apply a thin continuous layer of solid on the top of a tablet or a granule containing active pharmaceutical ingredients (APIs). Coating thickness and homogeneity are critical parameters regarding the drug release rate, and consequently a direct or indirect monitoring strategy of these critical process parameters is essential. With the aid of Optical Coherence Tomography (OCT) it is not only possible to measure the absolute coating thickness, but also to detect inhomogeneities in the coating or substrate material. In this work the possible application of OCT as in-line method for monitoring pharmaceutical tablet film coating is studied. Firstly, the feasibility of OCT for analysis tablet coating is examined. Seven different commercially available film-coated tablets with different shapes, formulations and coating thicknesses were investigated off-line. OCT images were acquired by two different spectral-domain OCT systems operating at center wavelengths of 830 and 1325 nm. Since the images of both systems allow the analysis of the coatings, the OCT system employing the shorter wavelength and thus providing a higher axial resolution was selected for the further experiments. The influence of a moving tablet bed on OCT images was analyzed by considering a static tablet bed and moving the sensor head along the tablet bed. The ability to analyze the coating homogeneity is limited to a speed up to 0.3 m/s. However, determining the coating thickness and inter-coating uniformity is still possible up to a speed of 0.7 m/s.

Ultra-high-stability, pH-resistant sol-gel titania poly(tetrahydrofuran) coating for capillary microextraction on-line coupled to high-performance liquid chromatography.

PubMed

Segro, Scott S; Cabezas, Yaniel; Malik, Abdul

2009-05-15

A sol-gel titania poly(tetrahydrofuran) (poly-THF) coating was developed for capillary microextraction hyphenated on-line with high-performance liquid chromatography (HPLC). Poly-THF was covalently bonded to the sol-gel titania network which, in turn, became chemically anchored to the inner surface of a 0.25mm I.D. fused silica capillary. For sample preconcentration, a 38-cm segment of the sol-gel titania poly-THF coated capillary was installed on an HPLC injection port as a sampling loop. Aqueous samples containing a variety of analytes were passed through the capillary and, during this process, the analytes were extracted by the sol-gel titania poly-THF coating on the inner surface of the capillary. Using isocratic and gradient elution with acetonitrile/water mobile phases, the extracted analytes were desorbed into the on-line coupled HPLC column for separation and UV detection. The sol-gel titania poly-THF coating was especially efficient in extracting polar analytes, such as underivatized phenols, alcohols, amines, and aromatic carboxylic acids. In addition, this coating was capable of extracting moderately polar and nonpolar analytes, such as ketones and polycyclic aromatic hydrocarbons. The sol-gel titania poly-THF coated capillary was also able to extract polypeptides at pH values near their respective isoelectric points. Extraction of these compounds can be important for environmental and biomedical applications. The observed extraction behavior can be attributed to the polar and nonpolar moieties in the poly-THF structure. This coating was found to be stable under extremely low and high pH conditions-even after 18h of exposure to 1M HCl (pH approximately 0.0) and 1M NaOH (pH approximately 14.0).

The Environmental Assessment and Management (TEAM) Guide: Delaware Supplement

DTIC Science & Technology

2010-01-01

December 2008]. • Coating or Printing - coating is the application of a uniform layer of material across the entire width of a web . Printing is...excess solvent by spinning, and drying by tumbling in any air stream. The facility includes, but is not limited to, any washer, dryer , or filter...mergency f ire , r escue o r co mmunications cal ls a nd operated either by the Delaware Emergency Management Agency or by any public agency or

SMALL DIAMETER CEMENT LINING FROM STAIRWAY. United States Pipe ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SMALL DIAMETER CEMENT LINING FROM STAIRWAY. - United States Pipe & Foundry Company Plant, Coating, Painting, Lining & Packaging Building, 2023 St. Louis Avenue at I-20/59, Bessemer, Jefferson County, AL

Aphid-parasitoid community structure on genetically modified wheat.

PubMed

von Burg, Simone; van Veen, Frank J F; Álvarez-Alfageme, Fernando; Romeis, Jörg

2011-06-23

Since the introduction of genetically modified (GM) plants, one of the main concerns has been their potential effect on non-target insects. Many studies have looked at GM plant effects on single non-target herbivore species or on simple herbivore-natural enemy food chains. Agro-ecosystems, however, are characterized by numerous insect species which are involved in complex interactions, forming food webs. In this study, we looked at transgenic disease-resistant wheat (Triticum aestivum) and its effect on aphid-parasitoid food webs. We hypothesized that the GM of the wheat lines directly or indirectly affect aphids and that these effects cascade up to change the structure of the associated food webs. Over 2 years, we studied different experimental wheat lines under semi-field conditions. We constructed quantitative food webs to compare their properties on GM lines with the properties on corresponding non-transgenic controls. We found significant effects of the different wheat lines on insect community structure up to the fourth trophic level. However, the observed effects were inconsistent between study years and the variation between wheat varieties was as big as between GM plants and their controls. This suggests that the impact of our powdery mildew-resistant GM wheat plants on food web structure may be negligible and potential ecological effects on non-target insects limited.

Impacting Motivation in the Virtual Classroom

ERIC Educational Resources Information Center

Artyushina, Galina; Sheypak, Olga

2012-01-01

Teachers, educational managers and learners must realize that new opportunities are offered by modern on-line communication. A person with basic Internet and Web skills is open to a new world of knowledge, from free Web surfing and self-organized education--through on-line resources and familiarization with Internet culture, its places, sites,…

WMI2, the Student's On-Line Symbolic Calculator

ERIC Educational Resources Information Center

Kovacs, Zoltan

2011-01-01

Student activities focused on discovering mathematics play an important role in the teaching and learning process. WebMathematics Interactive (WMI2) was developed to offer a fast and user-friendly on-line web interface to enhance the quality of both theoretical and applied mathematics courses. For the teacher, in the classroom, it provides…

Web-Based Menus: Font Size and Line Spacing Preferences.

ERIC Educational Resources Information Center

Pacheco, Janice; Day, Barbara Taylor; Cribelli, Susan; Jordan, John; Murry, Brandon; Persichitte, Kay A.

The study investigated the elements of font size and line spacing in World Wide Web menus for both a scrolled and not scrolled condition with a sample of undergraduate university students. Subjects were 185 students enrolled in 13 section of educational technology preservice teacher courses at the University of Northern Colorado. Students were…

24. The DryingRoom in the coating mill at Lawrence, Mass. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. The Drying-Room in the coating mill at Lawrence, Mass. After the paper has received its coating from the coating-machine shown in the previous picture, it passes in a continuous web to the drying-room. Blasts of hot air coming out of galvanized ducts beneath support it for a distance of 100 feet, until it reaches the drying-chamber in the rear of the room. Here it hangs in festoons much like those of cotton cloth shown on page 219. In the picture the paper is passing from right to left. After leaving the drying-room it is wound on rolls, as shown in the next picture. (p.238.) - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

Estimation of genetic parameters and selection of high-yielding, upright common bean lines with slow seed-coat darkening.

PubMed

Alvares, R C; Silva, F C; Melo, L C; Melo, P G S; Pereira, H S

2016-11-21

Slow seed coat darkening is desirable in common bean cultivars and genetic parameters are important to define breeding strategies. The aims of this study were to estimate genetic parameters for plant architecture, grain yield, grain size, and seed-coat darkening in common bean; identify any genetic association among these traits; and select lines that associate desirable phenotypes for these traits. Three experiments were set up in the winter 2012 growing season, in Santo Antônio de Goiás and Brasília, Brazil, including 220 lines obtained from four segregating populations and five parents. A triple lattice 15 x 15 experimental design was used. The traits evaluated were plant architecture, grain yield, grain size, and seed-coat darkening. Analyses of variance were carried out and genetic parameters such as heritability, gain expected from selection, and correlations, were estimated. For selection of superior lines, a "weight-free and parameter-free" index was used. The estimates of genetic variance, heritability, and gain expected from selection were high, indicating good possibility for success in selection of the four traits. The genotype x environment interaction was proportionally more important for yield than for the other traits. There was no strong genetic correlation observed among the four traits, which indicates the possibility of selection of superior lines with many traits. Considering simultaneous selection, it was not possible to join high genetic gains for the four traits. Forty-four lines that combined high yield, more upright plant architecture, slow darkening grains, and commercial grade size were selected.

Performance of multilayer coated diffraction gratings in the EUV

NASA Technical Reports Server (NTRS)

Keski-Kuha, Ritva A. M.; Thomas, Roger J.; Gum, Jeffrey S.; Condor, Charles E.

1990-01-01

The effect of multilayer coating application on the performance of a diffraction grating in the EUV spectral region was evaluated by examining the performance of a 3600-line/mm and a 1200-line/mm replica blazed gratings, designed for operation in the 300-A spectral region in first order. A ten-layer IrSi multilayer optimized for 304 A was deposited using electron-beam evaporation. The grating efficiency was measured on the SURF II calibration beamline in a chamber designed for calibrating the solar EUV rocket telescope and spectrograph multilayer coatings. A significant (by a factor of about 7) enhancement in grating efficiency in the 300-A region was demonstrated.

Development of optical WGM resonators for biosensors

NASA Astrophysics Data System (ADS)

Brice, I.; Pirktina, A.; Ubele, A.; Grundsteins, K.; Atvars, A.; Viter, R.; Alnis, J.

2017-12-01

Whispering Gallery Mode (WGM) resonators are very sensitive to nanoparticles attaching to the surface. We simulate this process using COMSOL Wave Optics module. Our spherical WGM resonators are produced by melting a tip of an optical fiber and we measure optical Q factors in the 105 range. Molecular oxygen lines of the air in the 760 nm region are used as reference markers when looking for the shifts of the WGM resonance lines. We demonstrate WGM microresonator surface coating with a layer of ZnO nanorods as well as with polystyrene microspheres. Coatings produce increased contact surface. Additional layer of antigens/antibodies will be coated to make high-specificity biosensors.

On-line capacity-building program on "analysis of data" for medical educators in the South Asia region: a qualitative exploration of our experience.

PubMed

Dongre, A R; Chacko, T V; Banu, S; Bhandary, S; Sahasrabudhe, R A; Philip, S; Deshmukh, P R

2010-11-01

In medical education, using the World Wide Web is a new approach for building the capacity of faculty. However, there is little information available on medical education researchers' needs and their collective learning outcomes in such on-line environments. Hence, the present study attempted: 1)to identify needs for capacity-building of fellows in a faculty development program on the topic of data analysis; and 2) to describe, analyze and understand the collective learning outcomes of the fellows during this need-based on-line session. The present research is based on quantitative (on-line survey for needs assessment) and qualitative (contents of e-mails exchanged in listserv discussion) data which were generated during the October 2009 Mentoring and Learning (M-L) Web discussion on the topic of data analysis. The data sources were shared e-mail responses during the process of planning and executing the M-L Web discussion. Content analysis was undertaken and the categories of discussion were presented as a simple non-hierarchical typology which represents the collective learning of the project fellows. We identified the types of learning needs on the topic 'Analysis of Data' to be addressed for faculty development in the field of education research. This need-based M-L Web discussion could then facilitate collective learning on such topics as 'basic concepts in statistics', tests of significance, Likert scale analysis, bivariate correlation, and simple regression analysis and content analysis of qualitative data. Steps like identifying the learning needs for an on-line M-L Web discussion, addressing the immediate needs of learners and creating a flexible reflective learning environment on the M-L Web facilitated the collective learning of the fellows on the topic of data analysis. Our outcomes can be useful in the design of on-line pedagogical strategies for supporting research in medical education.

SMALL DIAMETER PRECEMENT LINING FROM CATWALK ABOVE. United States ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SMALL DIAMETER PRE-CEMENT LINING FROM CATWALK ABOVE. - United States Pipe & Foundry Company Plant, Coating, Painting, Lining & Packaging Building, 2023 St. Louis Avenue at I-20/59, Bessemer, Jefferson County, AL

Method and apparatus for measuring on-line failure of turbine thermal barrier coatings

DOEpatents

Zombo, Paul J.; Lemieux, Dennis; Diatzikis, Evangelos

2010-04-06

A method of remotely monitoring the radiant energy (6) emitted from a turbine component such as a turbine blade (1) having a low-reflective surface coating (3) which may be undergoing potential degradation is used to determine whether erosion, spallation, delamination, or the like, of the coating (3) is occurring.

Astronomy On-Line Programme Enters "hot Week"

NASA Astrophysics Data System (ADS)

1996-11-01

World's Biggest Astronomy WWW-Event Attracts Thousands of Students The Astronomy On-line Programme (See ESO Press Release 09/96 of 18 June 1996) began officially on 1 October and is now about to enter its most intense phase, known as the Hot Week . On 18 - 22 November, an estimated 4000 astronomy-interested, mostly young people in Europe and on four other continents will get together during five days in what - not unexpected - has become the world's biggest astronomy event ever organised on the World Wide Web. This carefully structured Programme is carried out in collaboration between the European Association for Astronomy Education (EAAE), the European Southern Observatory and the European Commission, under the auspices of the Fourth European Week for Scientific and Technological Culture. The Programme has already had a most visible impact on the school education of natural sciences in various countries; for instance, the Internet-connection of schools has been advanced in some, in order to allow groups to participate. There have been numerous contacts among the groups across the borders and there are clear signs that many Astronomy On-line participants have progressed to use the impressive possibilities of the Web in an efficient and structured way. There has been a lively media interest in Astronomy On-line all over Europe and it is expected to increase during the next week. The current status of Astronomy On-line It is obvious that the pilot function of the Astronomy On-line Programme in the use of the Web has been very effective and that the associated dissemination of astronomical knowledge has been successful. At this time, more than 650 groups have registered with Astronomy On-line. Most come from 31 different European countries and a few dozen groups are located in North and South America as well as in Asia and Australia. Together they have experienced the steady build-up of Astronomy On-line over the past weeks, by means of numerous contributions from a large number of teachers, amateur astronomers and others interested in this field of science. The Astronomy On-line concept is that of a well-structured marketplace with a number of different shops which cater to the participants with a great variety of interesting and educational activities. These range from the availability of useful links to educational and scientific Web sites all around the world, collaborative projects where many participants in different countries work together to achieve an astronomical result and, not the least, the possibility to submit observing programmes to a dozen telescopes at 10 major observatories, including La Silla in Chile. In the early phases of Astronomy On-line , coordinated observations were performed of a lunar eclipse on 27 September and a partial solar eclipse on 12 October. Both events attracted many hundreds of observers from groups in almost all European countries and provisional reports have already been published on the Web. Many beautiful photographs and interesting reports about the activities of the individual groups are also available at their special Web sites. The Hot Week will last from Monday to Friday, 18-22 November and the time interval from 15:00-21:00 UT (16:00 - 22:00 Central European Time) will be the busiest. During this period, a variety of activities will take place. For instance, the groups will have the opportunity to contact professional astronomers at many observatories. They will also be invited to follow the other developments, e.g. the astronomical observations. The resulting images will immediately be made available on the Web. There will also be a Final Event involving all the groups. How to obtain more information about Astronomy On-line Astronomy On-line may be accessed through: http://www.eso.org/astronomyonline/ and http://www.algonet.se/~sirius/eaae.htm. National Astronomy On-line Committees have been established in many European countries. They have set up National Astronomy On-line Web-sites which can be reached directly from the sites indicated above. Information about the individual groups, their participants' interests as well as their postal, E-mail and Web addresses are also available, sorted by country. The addresses of the National organisers of Astronomy On-line may be found at these Web sites. A full report about this unique pilot project will become available before the end of this year. How to obtain ESO Press Information ESO Press Information is made available on the World-Wide Web (URL: http://www.eso.org../). ESO Press Photos may be reproduced, if credit is given to the European Southern Observatory.

Vibration Analysis of Commercial Thermal Barrier Coatings

DTIC Science & Technology

2008-06-01

Twenty-six beam specimens were cut by Kerf Waterjet in Dayton, OH. All specimens were cut from a single sheet of 1.6 mm thick Ti- 6Al - 4V . The beams...strain range, as measured at the center of the beam, for the mag spinel ranged from 874με to 905με. The yield stress for Ti- 6Al - 4V is 980 MPa (MatWeb...40  Figure 14: SEM Image of Mag Spinel and Bond Coat on Titanium ............................... 42  Figure 15: Beam

Membrane Bioreactor/Ultra Low Energy Reverse Osmosis Membrane Process for Forward Operating Base Wastewater Reuse

DTIC Science & Technology

2014-08-01

of the GEGR pilot membrane coater; b) configuration of the coating station; and c) web path of the dip-knife coating process for RO membrane...Energy-dispersive X-ray spectroscopy EPA Environmental Protection Agency F:M Food-To-Microorganism Ratio FOB Forward Operating Base FT- IR Fourier...report 03/2014 3.3 Submit draft Interim report/Go No-Go decision point white paper 05/2013 3.4 Submit final report 05/2014 3.5 Final debrief

Using PlacesOnline in Instructional Activities

ERIC Educational Resources Information Center

Longan, Michael W.; Owusu, Francis; Roseman, Curtis C.

2008-01-01

PlacesOnLine.org is a Web portal that provides easy access to high quality Web sites that focus on places from around the world. It is intended for use by a wide range of people, including professional geographers, teachers and students at all levels, and the general public. This article explores the potential uses of PlacesOnLine as an…

High voltage isolation transformer

NASA Technical Reports Server (NTRS)

Clatterbuck, C. H.; Ruitberg, A. P. (Inventor)

1985-01-01

A high voltage isolation transformer is provided with primary and secondary coils separated by discrete electrostatic shields from the surfaces of insulating spools on which the coils are wound. The electrostatic shields are formed by coatings of a compound with a low electrical conductivity which completely encase the coils and adhere to the surfaces of the insulating spools adjacent to the coils. Coatings of the compound also line axial bores of the spools, thereby forming electrostatic shields separating the spools from legs of a ferromagnetic core extending through the bores. The transformer is able to isolate a high constant potential applied to one of its coils, without the occurrence of sparking or corona, by coupling the coatings, lining the axial bores to the ferromagnetic core and by coupling one terminal of each coil to the respective coating encasing the coil.

High voltage isolation transformer

NASA Astrophysics Data System (ADS)

Clatterbuck, C. H.; Ruitberg, A. P.

1985-04-01

A high voltage isolation transformer is provided with primary and secondary coils separated by discrete electrostatic shields from the surfaces of insulating spools on which the coils are wound. The electrostatic shields are formed by coatings of a compound with a low electrical conductivity which completely encase the coils and adhere to the surfaces of the insulating spools adjacent to the coils. Coatings of the compound also line axial bores of the spools, thereby forming electrostatic shields separating the spools from legs of a ferromagnetic core extending through the bores. The transformer is able to isolate a high constant potential applied to one of its coils, without the occurrence of sparking or corona, by coupling the coatings, lining the axial bores to the ferromagnetic core and by coupling one terminal of each coil to the respective coating encasing the coil.

Development of search prefilters for infrared library searching of clear coat paint smears.

PubMed

Lavine, Barry K; Fasasi, Ayuba; Mirjankar, Nikhil; Sandercock, Mark

2014-02-01

Search prefilters developed from spectral data collected on two 6700 Thermo-Nicolet FTIR spectrometers were able to identify the respective manufacturing plant and the production line of an automotive vehicle from its clear coat paint smear using IR transmission spectra collected on a Bio-Rad 40A or Bio-Rad 60 FTIR spectrometer. All four spectrometers were equipped with DTGS detectors. An approach based on instrumental line functions was used to transfer the classification model between the Thermo-Nicolet and Bio-Rad instruments. In this study, 209 IR spectra of clear coat paint smears comprising the training set were collected using two Thermo-Nicolet 6700 IR spectrometers, whereas the validation set consisted of 242 IR spectra of clear coats obtained using two Bio-Rad FTIR instruments. © 2013 Published by Elsevier B.V.

Spin-on bottom antireflective coating defect reduction by proper filter selection and process optimization

NASA Astrophysics Data System (ADS)

Brakensiek, Nickolas L.; Kidd, Brian; Mesawich, Michael; Stevens, Don, Jr.; Gotlinsky, Barry

2003-06-01

A design of experiment (DOE) was implemented to show the effects of various point of use filters on the coat process. The DOE takes into account the filter media, pore size, and pumping means, such as dispense pressure, time, and spin speed. The coating was executed on a TEL Mark 8 coat track, with an IDI M450 pump, and PALL 16 stack Falcon filters. A KLA 2112 set at 0.69 μm pixel size was used to scan the wafers to detect and identify the defects. The process found for DUV42P to maintain a low defect coating irrespective of the filter or pore size is a high start pressure, low end pressure, low dispense time, and high dispense speed. The IDI M450 pump has the capability to compensate for bubble type defects by venting the defects out of the filter before the defects are in the dispense line and the variable dispense rate allows the material in the dispense line to slow down at the end of dispense and not create microbubbles in the dispense line or tip. Also the differential pressure sensor will alarm if the pressure differential across the filter increases over a user-determined setpoint. The pleat design allows more surface area in the same footprint to reduce the differential pressure across the filter and transport defects to the vent tube. The correct low defect coating process will maximize the advantage of reducing filter pore size or changing the filter media.

Effect of location and ionic interaction on photocatalytic activity of silver nanoparticles stabilized with polyDOPA

NASA Astrophysics Data System (ADS)

Cheon, Ja Young; Park, Won Ho

2018-05-01

PVA nanofibrous webs containing silver nanoparticles (Ag NPs) stabilized with poly(3,4-dihydroxyphenylalanine) (polyDOPA) were prepared using either the electrospinning or coating methods. The Ag NPs incorporated in the nanofibers were identified using SEM, TEM, TGA, and XRD. The catalytic reactions of the PVA nanofibrous webs containing the Ag NPs were compared using organic dyes under UV-vis spectroscopy. The location (inside and outside) of the Ag NPs in the nanofibers and the charge interaction between the dye and the Ag NPs had a significant effect on the catalytic reaction rate. When the Ag NPs existed in the outside of the nanofiber due to the coating method, the reaction rate was increased due to the presence of more contact sites with respect to the organic dye. Also, an electrostatic attraction between the organic dye and the pDA surrounding the Ag NPs increased the catalytic reaction rate. Therefore, it was demonstrated that the location and the surface charge of the Ag NPs in the nanofibrous web should be considered as crucial factors in terms of the catalytic performance of the Ag NPs for model dyes.

Safer Pleasure Boats

NASA Technical Reports Server (NTRS)

1976-01-01

'Flamarest' coating developed by Avco Corporation for NASA to protect fuel lines and tanks is sprayed on the interior of polyester boat hull in commercial application. About 30 mils of the coating prevented structural damage to hull during test in which a 13 minute interior gasoline fire was started. An unprotected hull would begin to burn in 30 seconds. Same material applied as tape to wrap fuel lines effectively insulates hose when charred while also reducing spread of flame.

Coating of large-sized optics for the instruments of observation

NASA Astrophysics Data System (ADS)

Mouricaud, Daniel

2008-07-01

SAGEM has developed a line of product specific to the large-sized parts. The means available make it possible today to coat substrates of dimensions going until 1m50. Current developments address coating of substrate up to 2m20. A specific focus has been held on the wavefront deformation due to the coating. Principle contributors of this deformation are introduced and analyzed as well as some experimental results.

Experimental use of Line-X coated steel pipe piles, Clay Hill Bridge (#2157) replacement project over the Mousam River, Route 9/Western Avenue, Kennebunk, Maine.

DOT National Transportation Integrated Search

2013-02-01

Steel pipe piles used by MaineDOT for bridge construction are typically coated with a fusion-bonded epoxy (FBE). FBE is a powder-based coating with properties similar to traditional : epoxies. Its name is derived from the process by which it adheres ...

Stent Coating Integrity of Durable and Biodegradable Coated Drug Eluting Stents.

PubMed

Yazdani, Saami K; Sheehy, Alexander; Pacetti, Stephen; Rittlemeyer, Brandon; Kolodgie, Frank D; Virmani, Renu

2016-10-01

Coatings consisting of a polymer and drug are widely used in drug-eluting stents (DES) and are essential in providing programmable drug release kinetics. Among other factors, stent coating technologies can influence blood compatibility, affect acute and sub-acute healing, and potentially trigger a chronic inflammatory response. The aim of this study was to investigate the short-term (7 and 28 days) and long-term (90 and 180 days) coating integrity of the Xience Prime Everolimus-Eluting Stent (EES), Resolute Zotarolimus-Eluting Stent (ZES), Taxus Paclitaxel-Eluting Stent (PES), and Nobori Biolimus A9-Eluting Stent (BES) in a rabbit ilio-femoral stent model. Stented arteries (n = 48) were harvested and the tissue surrounding the implanted stents digested away with an enzymatic solution. Results demonstrated that the majority of struts of EES were without any coating defects with a few struts showing minor defects. Similarly, for the ZES, most of the struts were without coating defects at all time points except at 180 days. The majority of PES demonstrated mostly webbing and uneven coating. In the BES group, the majority of strut coating showed polymer cracking. Overall, the EES and ZES had fewer coating defects than the PES and BES. Coating defects, however increase over time for the ZES, whereas the percent of coating irregularities remained constant for the EES. These results provide, for the first time, a comparison of the long-term durability of these drug-eluting stent coatings in vivo. © 2016, Wiley Periodicals, Inc.

Study of Corrosion Resistance Improvement by Metallic Coating for Overhead Transmission Line Conductor

NASA Astrophysics Data System (ADS)

Isozaki, Masanori; Adachi, Kouichi; Hita, Takanori; Asano, Yuji

Applying anti-corrosion grease and aluminum clad steel (AC) wires to ACSR has adopted as general methods to prevent overhead transmission line conductors and/or wires from corrosion. However, there are some cases that ineffectiveness of those means are reported on some transmission lines passing through acid atmosphere in the vicinity of a factory exhausting acid smoke. The feature of the corrosion caused by acid atmosphere is to show a higher speed in its progressing as well known. As means against such acid corrosion, application of high purity aluminum, selective removal of inter-metallic compound in aluminum and plastic coating wires has been reported before, and each has both of advantage and disadvantage actually. In the former letter, we reported the new type of anti-corrosion grease that shows an excellent property against acid atmosphere as well as in a salty circumstance. Here presents a new type of anti-corrosion technology of applying high corrosion resistance aluminum alloy or zinc coatings on each component wires of a conductor that we succeed in developing through a serial study of anti-corrosion methods on overhead transmission lines.

Does hydroxyapatite coating have no advantage over porous coating in primary total hip arthroplasty? A meta-analysis.

PubMed

Chen, Yun-Lin; Lin, Tiao; Liu, An; Shi, Ming-Min; Hu, Bin; Shi, Zhong-Li; Yan, Shi-Gui

2015-01-28

There are some arguments between the use of hydroxyapatite and porous coating. Some studies have shown that there is no difference between these two coatings in total hip arthroplasty (THA), while several other studies have shown that hydroxyapatite has advantages over the porous one. We have collected the studies in Pubmed, MEDLINE, EMBASE, and the Cochrane library from the earliest possible years to present, with the search strategy of "(HA OR hydroxyapatite) AND ((total hip arthroplasty) OR (total hip replacement)) AND (RCT* OR randomiz* OR control* OR compar* OR trial*)". The randomized controlled trials and comparative observation trials that evaluated the clinical and radiographic effects between hydroxyapatite coating and porous coating were included. Our main outcome measurements were Harris hip score (HHS) and survival, while the secondary outcome measurements were osteolysis, radiolucent lines, and polyethylene wear. Twelve RCTs and 9 comparative observation trials were included. Hydroxyapatite coating could improve the HHS (p < 0.01), reduce the incidence of thigh pain (p = 0.01), and reduce the incidence of femoral osteolysis (p = 0.01), but hydroxyapatite coating had no advantages on survival (p = 0.32), polyethylene wear (p = 0.08), and radiolucent lines (p = 0.78). Hydroxyapatite coating has shown to have an advantage over porous coating. The HHS and survival was duration-dependent-if given the sufficient duration of follow-up, hydroxyapatite coating would be better than porous coating for the survival. The properties of hydroxyapatite and the implant design had influence on thigh pain incidence, femoral osteolysis, and polyethylene wear. Thickness of 50 to 80 μm and purity larger than 90% increased the thigh pain incidence. Anatomic design had less polyethylene wear.

Assessing an Infant Feeding Web Site as a Nutrition Education Tool for Child Care Providers

ERIC Educational Resources Information Center

Clark, Alena; Anderson, Jennifer; Adams, Elizabeth; Baker, Susan; Barrett, Karen

2009-01-01

Objective: Determine child care providers' infant feeding knowledge, attitude and behavior changes after viewing the infant feeding Web site and determine the effectiveness of the Web site and bilingual educational materials. Design: Intervention and control groups completed an on-line pretest survey, viewed a Web site for 3 months, and completed…

From webs to polylogarithms

NASA Astrophysics Data System (ADS)

Gardi, Einan

2014-04-01

We compute a class of diagrams contributing to the multi-leg soft anomalous dimension through three loops, by renormalizing a product of semi-infinite non-lightlike Wilson lines in dimensional regularization. Using non-Abelian exponentiation we directly compute contributions to the exponent in terms of webs. We develop a general strategy to compute webs with multiple gluon exchanges between Wilson lines in configuration space, and explore their analytic structure in terms of α ij , the exponential of the Minkowski cusp angle formed between the lines i and j. We show that beyond the obvious inversion symmetry α ij → 1 /α ij , at the level of the symbol the result also admits a crossing symmetry α ij → - α ij , relating spacelike and timelike kinematics, and hence argue that in this class of webs the symbol alphabet is restricted to α ij and . We carry out the calculation up to three gluons connecting four Wilson lines, finding that the contributions to the soft anomalous dimension are remarkably simple: they involve pure functions of uniform weight, which are written as a sum of products of polylogarithms, each depending on a single cusp angle. We conjecture that this type of factorization extends to all multiple-gluon-exchange contributions to the anomalous dimension.

Fiber optic interferometry for industrial process monitoring and control applications

NASA Astrophysics Data System (ADS)

Marcus, Michael A.

2002-02-01

Over the past few years we have been developing applications for a high-resolution (sub-micron accuracy) fiber optic coupled dual Michelson interferometer-based instrument. It is being utilized in a variety of applications including monitoring liquid layer thickness uniformity on coating hoppers, film base thickness uniformity measurement, digital camera focus assessment, optical cell path length assessment and imager and wafer surface profile mapping. The instrument includes both coherent and non-coherent light sources, custom application dependent optical probes and sample interfaces, a Michelson interferometer, custom electronics, a Pentium-based PC with data acquisition cards and LabWindows CVI or LabView based application specific software. This paper describes the development evolution of this instrument platform and applications highlighting robust instrument design, hardware, software, and user interfaces development. The talk concludes with a discussion of a new high-speed instrument configuration, which can be utilized for high speed surface profiling and as an on-line web thickness gauge.

Microstructural Effects and Properties of Non-line-of-Sight Coating Processing via Plasma Spray-Physical Vapor Deposition

NASA Astrophysics Data System (ADS)

Harder, Bryan J.; Zhu, Dongming; Schmitt, Michael P.; Wolfe, Douglas E.

2017-08-01

Plasma spray-physical vapor deposition (PS-PVD) is a unique processing method that bridges the gap between conventional thermal spray and vapor phase methods, and enables highly tailorable coatings composed of a variety of materials in thin, dense layers or columnar microstructures with modification of the processing conditions. The strengths of this processing technique are material and microstructural flexibility, deposition speed, and potential for non-line-of-sight (NLOS) capability by vaporization of the feedstock material. The NLOS capability of PS-PVD is investigated here using yttria-stabilized zirconia and gadolinium zirconate, which are materials of interest for turbine engine applications. PS-PVD coatings were applied to static cylindrical substrates approximately 6-19 mm in diameter to study the coating morphology as a function of angle. In addition, coatings were deposited on flat substrates under various impingement configurations. Impingement angle had significant effects on the deposition mode, and microscopy of coatings indicated that there was a shift in the deposition mode at approximately 90° from incidence on the cylindrical samples, which may indicate the onset of more turbulent flow and PVD-like growth. Coatings deposited at non-perpendicular angles exhibited a higher density and nearly a 2× improvement in erosion performance when compared to coatings deposited with the torch normal to the surface.

Cross Coating Weight Control by Electromagnetic Strip Stabilization at the Continuous Galvanizing Line of ArcelorMittal Florange

NASA Astrophysics Data System (ADS)

Guelton, Nicolas; Lopès, Catherine; Sordini, Henri

2016-08-01

In hot dip galvanizing lines, strip bending around the sink roll generates a flatness defect called crossbow. This defect affects the cross coating weight distribution by changing the knife-to-strip distance along the strip width and requires a significant increase in coating target to prevent any risk of undercoating. The already-existing coating weight control system succeeds in eliminating both average and skew coating errors but cannot do anything against crossbow coating errors. It has therefore been upgraded with a flatness correction function which takes advantage of the possibility of controlling the electromagnetic stabilizer. The basic principle is to split, for every gage scan, the coating weight cross profile of the top and bottom sides into two, respectively, linear and non-linear components. The linear component is used to correct the skew error by realigning the knives with the strip, while the non-linear component is used to distort the strip in the stabilizer in such a way that the strip is kept flat between the knives. Industrial evaluation is currently in progress but the first results have already shown that the strip can be significantly flattened between the knives and the production tolerances subsequently tightened without compromising quality.

77 FR 22780 - Certain New Chemicals; Receipt and Status Information

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... phenolic- epoxy coating system used to produce a water-immersion lining on concrete and steel. The coating... 06/17/2012 Shepherd Color Company (S) Colored pigment (S) Niobium sulfur tin zinc used. oxide. P-12...

INTERIOR VIEW, LOOKING WEST, WITH PIPE BEING SPRAYED WITH ZINC ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING WEST, WITH PIPE BEING SPRAYED WITH ZINC COATING. - United States Pipe & Foundry Company Plant, Coating, Painting, Lining & Packaging Building, 2023 St. Louis Avenue at I-20/59, Bessemer, Jefferson County, AL

Dancing girl flap: a new flap suitable for web release.

PubMed

Shinya, K

1999-12-01

To create a deep web, a flap must be designed to have a high elongation effect in one direction along the mid-lateral line of the finger and also to have a shortening effect in the other direction, crossing at a right angle to the mid-lateral line. The dancing girl flap is a modification of a four-flap Z-plasty with two additional Z-plasties. It has a high elongation effect in one direction (>550%) and a shortening effect in the other direction at a right angle (<33%), creating a deep, U-shaped surface. This new flap can be used to release severe scar contracture with a web, and is most suitable for incomplete syndactyly with webs as high as the proximal interphalangeal joint.

Analysis of liquid-phase chemical detection using guided shear horizontal-surface acoustic wave sensors.

PubMed

Li, Zhonghui; Jones, Yolanda; Hossenlopp, Jeanne; Cernosek, Richard; Josse, Fabien

2005-07-15

Direct chemical sensing in liquid environments using polymer-guided shear horizontal surface acoustic wave sensor platforms on 36 degrees rotated Y-cut LiTaO3 is investigated. Design considerations for optimizing these devices for liquid-phase detection are systematically explored. Two different sensor geometries are experimentally and theoretically analyzed. Dual delay line devices are used with a reference line coated with poly (methyl methacrylate) (PMMA) and a sensing line coated with a chemically sensitive polymer, which acts as both a guiding layer and a sensing layer or with a PMMA waveguide and a chemically sensitive polymer. Results show the three-layer model provides higher sensitivity than the four-layer model. Contributions from mass loading and coating viscoelasticity changes to the sensor response are evaluated, taking into account the added mass, swelling, and plasticization. Chemically sensitive polymers are investigated in the detection of low concentrations (1-60 ppm) of toluene, ethylbenzene, and xylenes in water. A low-ppb level detection limit is estimated from the present experimental measurements. Sensor properties are investigated by varying the sensor geometries, coating thickness combinations, coating properties, and curing temperature for operation in liquid environments. Partition coefficients for polymer-aqueous analyte pairs are used to explain the observed trend in sensitivity for the polymers PMMA, poly(isobutylene), poly(epichlorohydrin), and poly(ethyl acrylate) used in this work.

The New Web-Based Hera Data Processing System at the HEASARC

NASA Technical Reports Server (NTRS)

Pence, W.

2011-01-01

The HEASARC at NASA/GSFC has provide an on-line astronomical data processing system called Hera for several years. Hera provides a complete data processing environment, including installed software packages, local data storage, and the CPU resources needed to process the user's data. The original design of Hera, however, has 2 requirements that has limited it's usefulness for some users, namely, that 1) the user must download and install a small helper program on their own computer before using Hera, and 2) Hera requires that several computer ports/sockets be allowed to communicate through any local firewalls on the users machine. Both of these restrictions can be problematic for some users, therefore we are now migrating Hera into a purely Web based environment which only requires a standard Web browser. The first release of Web Hera is now publicly available at http://heasarc.gsfc.nasa.gov/webheara/. It currently provides a standard graphical interface for running hundreds of different data processing programs that are available in the HEASARC's ftools software package. Over the next year we to add more features to Web Hera, including an interactive command line interface, and more display and line capabilities.

The structurally effect of surface coated rhamnogalacturonan I on response of the osteoblast-like cell line SaOS-2.

PubMed

Svava, Rikke; Gurzawska, Katarzyna; Yihau, Yu; Haugshøj, Kenneth Brian; Dirscherl, Kai; Levery, Steven B; Jørgensen, Niklas Rye; Gotfredsen, Klaus; Damager, Iben; Ulvskov, Peter; Jørgensen, Bodil

2014-06-01

Osseointegration is important when implants are inserted into the bone and can be improved by biochemical surface coating of the implant. In this paper enzymatically modified rhamnogalacturonan I (RG-I) from apple and lupin was used for biochemical coating of aminated surfaces and the importance of the quality of RG-I, the nature of the binding, the fine structure of RG-I, and its effect on SaOS-2 cell line cultured on coated surfaces was investigated. SaOS-2 cells are osteoblast-like cells and a well-established in vitro model of bone-matrix forming osteoblasts. Purification by gel filtration could remove small fragments of galacturonic acid (GalA) and binding studies showed that the purity of the RG-I molecules was important for the quality of the coating. The structure of RG-I and osteoblast-like cells' viability were positively correlated so that high content of 1,4-linked galactose (Gal) and a low content of arabinose in the RG-I molecules favored cell viability. These results indicate that coating of implants with RG-I affect osseointegration positively. Copyright © 2013 Wiley Periodicals, Inc.

The line roughness improvement with plasma coating and cure treatment for 193nm lithography and beyond

NASA Astrophysics Data System (ADS)

Zheng, Erhu; Huang, Yi; Zhang, Haiyang

2017-03-01

As CMOS technology reaches 14nm node and beyond, one of the key challenges of the extension of 193nm immersion lithography is how to control the line edge and width roughness (LER/LWR). For Self-aligned Multiple Patterning (SaMP), LER becomes larger while LWR becomes smaller as the process proceeds[1]. It means plasma etch process becomes more and more dominant for LER reduction. In this work, we mainly focus on the core etch solution including an extra plasma coating process introduced before the bottom anti reflective coating (BARC) open step, and an extra plasma cure process applied right after BARC-open step. Firstly, we leveraged the optimal design experiment (ODE) to investigate the impact of plasma coating step on LER and identified the optimal condition. ODE is an appropriate method for the screening experiments of non-linear parameters in dynamic process models, especially for high-cost-intensive industry [2]. Finally, we obtained the proper plasma coating treatment condition that has been proven to achieve 32% LER improvement compared with standard process. Furthermore, the plasma cure scheme has been also optimized with ODE method to cover the LWR degradation induced by plasma coating treatment.

Putting post-registration nursing students on-line: important lessons learned.

PubMed

Wharrad, Heather J; Cook, Elaine; Poussa, Cherry

2005-05-01

A web site and discussion forum to support a part time degree course for nurses was introduced not only to support student learning but also to encourage students to use and develop their IT skills. Previous cohorts had identified that health informatics skills needed to be addressed more explicitly throughout the programme. The aims of the project were to: (i) evaluate the use of the web site and discussion forum; (ii) determine the barriers to using the web site and discussion forum; (iii) identify ways of overcoming any barriers. The first aim was addressed by analysing web page hits and contributions to the discussion forum. Students' experiences of using the web site and the discussion forum were collected using a questionnaire and followed up by a focus group made up of high and low users of the discussion forum. Students who had accessed the web site most often felt they had been able to communicate with their peers (Spearman's rho, p < 0.01) and had gained peer support by accessing the web site (Spearman's rho, p > 0.05). None of the participants in this study had used a discussion forum before and whilst some students had the skills and confidence to contribute to the on-line discussions, others 'lurked' and some did not access the discussion facility at all. Strategies for improving the engagement and quality of on-line learning are proposed from the lessons learned during this study.

Applicability of near-infrared spectroscopy in the monitoring of film coating and curing process of the prolonged release coated pellets.

PubMed

Korasa, Klemen; Hudovornik, Grega; Vrečer, Franc

2016-10-10

Although process analytical technology (PAT) guidance has been introduced to the pharmaceutical industry just a decade ago, this innovative approach has already become an important part of efficient pharmaceutical development, manufacturing, and quality assurance. PAT tools are especially important in technologically complex operations which require strict control of critical process parameters and have significant effect on final product quality. Manufacturing of prolonged release film coated pellets is definitely one of such processes. The aim of the present work was to study the applicability of the at-line near-infrared spectroscopy (NIR) approach in the monitoring of pellet film coating and curing steps. Film coated pellets were manufactured by coating the active ingredient containing pellets with film coating based on polymethacrylate polymers (Eudragit® RS/RL). The NIR proved as a useful tool for the monitoring of the curing process since it was able to determine the extent of the curing and hence predict drug release rate by using partial least square (PLS) model. However, such approach also showed a number of limitations, such as low reliability and high susceptibility to pellet moisture content, and was thus not able to predict drug release from pellets with high moisture content. On the other hand, the at-line NIR was capable to predict the thickness of Eudragit® RS/RL film coating in a wide range (up to 40μm) with good accuracy even in the pellets with high moisture content. To sum up, high applicability of the at-line NIR in the monitoring of the prolonged release pellets production was demonstrated in the present study. The present findings may contribute to more efficient and reliable PAT solutions in the manufacturing of prolonged release dosage forms. Copyright © 2016 Elsevier B.V. All rights reserved.

76 FR 62419 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... Agency's Web site and call the appropriate advisory committee hot line/phone line to learn about possible... wrinkles in the face. The AQUAMID dermal filler is intended for use in mid-to-deep sub-dermal implantation... before the meeting. If FDA is unable to post the background material on its Web site prior to the meeting...

Drying of fiber webs

DOEpatents

Warren, David W.

1997-01-01

A process and an apparatus for high-intensity drying of fiber webs or sheets, such as newsprint, printing and writing papers, packaging paper, and paperboard or linerboard, as they are formed on a paper machine. The invention uses direct contact between the wet fiber web or sheet and various molten heat transfer fluids, such as liquified eutectic metal alloys, to impart heat at high rates over prolonged durations, in order to achieve ambient boiling of moisture contained within the web. The molten fluid contact process causes steam vapor to emanate from the web surface, without dilution by ambient air; and it is differentiated from the evaporative drying techniques of the prior industrial art, which depend on the uses of steam-heated cylinders to supply heat to the paper web surface, and ambient air to carry away moisture, which is evaporated from the web surface. Contact between the wet fiber web and the molten fluid can be accomplished either by submersing the web within a molten bath or by coating the surface of the web with the molten media. Because of the high interfacial surface tension between the molten media and the cellulose fiber comprising the paper web, the molten media does not appreciately stick to the paper after it is dried. Steam generated from the paper web is collected and condensed without dilution by ambient air to allow heat recovery at significantly higher temperature levels than attainable in evaporative dryers.

40 CFR 63.3410 - What records must I keep?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Section 63.3410 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating Notifications, Reports, and Records § 63...

40 CFR 63.3410 - What records must I keep?

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 63.3410 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating Notifications, Reports, and Records § 63...

Consequences of electrical conductivity in an orb spider's capture web

NASA Astrophysics Data System (ADS)

Vollrath, Fritz; Edmonds, Donald

2013-12-01

The glue-coated and wet capture spiral of the orb web of the garden cross spider Araneus diadematus is suspended between the dry silk radial and web frame threads. Here, we experimentally demonstrate that the capture spiral is electrically conductive because of necks of liquid connecting the droplets even if the thread is stretched. We examine how this conductivity of the capture spiral may lead to entrapment of charged airborne particles such as pollen, spray droplets and even insects. We further describe and model how the conducting spiral will also locally distort the Earth's ambient electric field. Finally, we examine the hypothesis that such distortion could be used by potential prey to detect the presence of a web but conclude that any effect would probably be too small to allow an insect to take evasive action.

Development of high-efficiency solar cells on silicon web

NASA Technical Reports Server (NTRS)

Meier, D. L.; Greggi, J.; Rai-Choudhury, P.

1986-01-01

Work is reported aimed at identifying and reducing sources of carrier recombination both in the starting web silicon material and in the processed cells. Cross-sectional transmission electron microscopy measurements of several web cells were made and analyzed. The effect of the heavily twinned region on cell efficiency was modeled, and the modeling results compared to measured values for processed cells. The effects of low energy, high dose hydrogen ion implantation on cell efficiency and diffusion length were examined. Cells were fabricated from web silicon known to have a high diffusion length, with a new double layer antireflection coating being applied to these cells. A new contact system, to be used with oxide passivated cells and which greatly reduces the area of contact between metal and silicon, was designed. The application of DLTS measurements to beveled samples was further investigated.

Approximation of effective moisture-diffusion coefficient to characterize performance of a barrier coating

NASA Astrophysics Data System (ADS)

Nagai, Shingo

2013-11-01

We report estimation of the effective diffusion coefficient of moisture through a barrier coating to develop an encapsulation technology for the thin-film electronics industry. This investigation targeted a silicon oxide (SiOx) film that was deposited on a plastic substrate by a large-process-area web coater. Using the finite difference method based on diffusion theory, our estimation of the effective diffusion coefficient of a SiOx film corresponded to that of bulk glass that was previously reported. This result suggested that the low diffusivities of barrier films can be obtained on a mass-production level in the factory. In this investigation, experimental observations and mathematical confirmation revealed the limit of the water vapor transmission rate on the single barrier coating.

New temperable solar coatings: Tempsol

NASA Astrophysics Data System (ADS)

Demiryont, Hulya

2001-11-01

This paper deals with the large area deposition and coating properties of the thermo-stable (temperable/bendable) solar coating material, CuO, and some new optical coating systems comprising CuO films for architectural and automotive/transportation applications. The CuO solar coating is combined with other coating layers, for example, an anti-reflection film, a reflection film, a coloration coating layer, etc., which are also thermo-stable. The film systems are developed at the research laboratory by D.C. Magnetron reactive sputtering process. The new developed technologies then transferred to the production line. Product performances are compared before and after heat treatment of the coating systems. Performance tables and other physical properties, including optical parameters, mechanical and environmental stability, storage properties, etc., are also presented for this new product series.

Intelligent Web-Based Learning System with Personalized Learning Path Guidance

ERIC Educational Resources Information Center

Chen, C. M.

2008-01-01

Personalized curriculum sequencing is an important research issue for web-based learning systems because no fixed learning paths will be appropriate for all learners. Therefore, many researchers focused on developing e-learning systems with personalized learning mechanisms to assist on-line web-based learning and adaptively provide learning paths…

78 FR 2919 - Proposed Priority-National Institute on Disability and Rehabilitation Research-Disability and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-15

... Rehabilitation Research--Disability and Rehabilitation Research Project--Inclusive Cloud and Web Computing CFDA... inclusive Cloud and Web computing. The Assistant Secretary may use this priority for competitions in fiscal... Priority for Inclusive Cloud and Web Computing'' in the subject line of your electronic message. FOR...

Advanced Visualization and Interactive Display Rapid Innovation and Discovery Evaluation Research Program task 8: Survey of WEBGL Graphics Engines

DTIC Science & Technology

2015-01-01

1 3.0 Methods, Assumptions, and Procedures ...18 4.6.3. LineUp Web... Procedures A search of the internet looking at web sites specializing in graphics, graphics engines, web browser applications, and games was conducted to

"I Guess It Was Pretty Fun": Using WebQuests in the Middle School Classroom.

ERIC Educational Resources Information Center

Lipscomb, George

2003-01-01

Notes that the WebQuest helps students harness the vast amount of on-line resources available. Presents a list of 10 suggestions that may help teachers unfamiliar with WebQuests, especially those in the history classroom, to use them more effectively. Concludes that students learned a great deal about the Civil War by doing the WebQuest, and the…

Multilingual Speech and Language Processing

DTIC Science & Technology

2003-04-01

client software handles the user end of the transaction. Historically, four clients were provided: e-mail, web, FrameMaker , and command line. By...command-line client and an API. The API allows integration of CyberTrans into a number of processes including word processing packages ( FrameMaker ...preservation and logging, and others. The available clients remain e-mail, Web and FrameMaker . Platforms include both Unix and PC for clients, with

Free-standing coating patterns fabricated by ultraviolet contact lithography using photosensitive sol-gel coatings

NASA Astrophysics Data System (ADS)

Xiang, Youlai; Du, Ai; Li, Xiaoguang; Sun, Wei; Wu, Shuai; Li, Tiemin; Liu, Mingfang; Zhou, Bin

2017-07-01

Photosensitive ZrO2-SiO2 hybrid sol-gel coatings containing large contents of chelating rings were prepared by using the zirconium n-butoxide (TBOZ) and methyltriethoxysilane (MTES) as hybrid precursors, and benzoylacetone (BZAC) as chelating agent. The change of ultraviolet (UV) absorption spectra, chemical composition, and optical properties of ZrO2-SiO2 hybrid sol-gel coatings were analyzed before and after UV exposure and calcination. The refractive index of the ZrO2-SiO2 hybrid gel coatings decreased from 1.673 to 1.561 with the increase of the molar content of MTES in precursors. The sol-gel coating patterns with the periods of 20.24 μm, 10.11 μm and 3.99 μm on the PAMS substrates were firstly obtained by using the photosensitive ZrO2-SiO2 hybrid sol-gel films as fundamental materials through a process of UV contact lithography with photo masks and etching with ethanol. Finally, the free-standing gel coating patterns supported by copper grids, with the period of 12.70 μm and line width of 4.93 μm, and the period of 14.20 μm and line width of 3.82 μm, were obtained by removing the PAMS thermal degradation sacrifice layer after being calcined at 330 °C. Micrometer-periodic free-standing gel coating patterns with different structure have potential applications in the laser physical experiments.

HealthLines: Heart-Safe Exercise

MedlinePlus

... funded by the National Institute of Environmental Health Sciences and the National Institute of Allergy and Infectious Diseases. Check Out Health-Helpful Web Sites MedlinePlus.gov and other NIH Web sites ...

In-line quality control of moving objects by means of spectral-domain OCT

NASA Astrophysics Data System (ADS)

Markl, Daniel; Hannesschläger, Günther; Buchsbaum, Andreas; Sacher, Stephan; Khinast, Johannes G.; Leitner, Michael

2014-08-01

In-line quality control of intermediate and final products is essential in various industries. This may imply determining the thickness of a foil or evaluating the homogeneity of coating applied to a pharmaceutical tablet. Such a qualitative and quantitative monitoring in a depth-resolved manner can be accomplished using optical coherence tomography (OCT). In-line quality control based on OCT requires additional consideration of motion effects for the system design as well as for data interpretation. This study focuses on transverse motion effects that can arise in spectral-domain (SD-) OCT systems. The impact of a transverse movement is analyzed for a constant relative speed difference up to 0.7 m/s between sample and sensor head. In particular, transverse motion is affecting OCT system properties such as the beam displacement (distance between adjacent A-scans) and transverse resolution. These properties were evaluated theoretically and experimentally for OCT images of a resolution target and pharmaceutical film-coated tablets. Both theoretical and experimental analyses highlight the shift of the transverse resolution limiting factor from the optics to the beam displacement above a relative speed difference between sensor head and sample of 0.42 m/s (for the presented SD-OCT setup). Speeds above 0.4 m/s are often demanded when monitoring industrial processes, such as a coating process when producing film-coated tablets. This emphasizes the importance of a fast data acquisition when using OCT as in-line quality control tool.

77 FR 5489 - Identification of Human Cell Lines Project

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-03

...-01] Identification of Human Cell Lines Project AGENCY: National Institute of Standards and Technology... cell line samples as part of the Identification of Human Cell Lines Project. All data and corresponding... cell lines accepted on the NIST Applied Genetics Group Web site at http://www.nist.gov/mml/biochemical...

An Application of X-Ray Fluorescence as Process Analytical Technology (PAT) to Monitor Particle Coating Processes.

PubMed

Nakano, Yoshio; Katakuse, Yoshimitsu; Azechi, Yasutaka

2018-06-01

An attempt to apply X-Ray Fluorescence (XRF) analysis to evaluate small particle coating process as a Process Analytical Technologies (PAT) was made. The XRF analysis was used to monitor coating level in small particle coating process with at-line manner. The small particle coating process usually consists of multiple coating processes. This study was conducted by a simple coating particles prepared by first coating of a model compound (DL-methionine) and second coating by talc on spherical microcrystalline cellulose cores. The particles with two layered coating are enough to demonstrate the small particle coating process. From the result by the small particle coating process, it was found that the XRF signal played different roles, resulting that XRF signals by first coating (layering) and second coating (mask coating) could demonstrate the extent with different mechanisms for the coating process. Furthermore, the particle coating of the different particle size has also been investigated to evaluate size effect of these coating processes. From these results, it was concluded that the XRF could be used as a PAT in monitoring particle coating processes and become powerful tool in pharmaceutical manufacturing.

Remote sensing education and Internet/World Wide Web technology

USGS Publications Warehouse

Griffith, J.A.; Egbert, S.L.

2001-01-01

Remote sensing education is increasingly in demand across academic and professional disciplines. Meanwhile, Internet technology and the World Wide Web (WWW) are being more frequently employed as teaching tools in remote sensing and other disciplines. The current wealth of information on the Internet and World Wide Web must be distilled, nonetheless, to be useful in remote sensing education. An extensive literature base is developing on the WWW as a tool in education and in teaching remote sensing. This literature reveals benefits and limitations of the WWW, and can guide its implementation. Among the most beneficial aspects of the Web are increased access to remote sensing expertise regardless of geographic location, increased access to current material, and access to extensive archives of satellite imagery and aerial photography. As with other teaching innovations, using the WWW/Internet may well mean more work, not less, for teachers, at least at the stage of early adoption. Also, information posted on Web sites is not always accurate. Development stages of this technology range from on-line posting of syllabi and lecture notes to on-line laboratory exercises and animated landscape flyovers and on-line image processing. The advantages of WWW/Internet technology may likely outweigh the costs of implementing it as a teaching tool.

Differential Effects of Tissue Culture Coating Substrates on Prostate Cancer Cell Adherence, Morphology and Behavior

PubMed Central

Liberio, Michelle S.; Sadowski, Martin C.; Soekmadji, Carolina; Davis, Rohan A.; Nelson, Colleen C.

2014-01-01

Weak cell-surface adhesion of cell lines to tissue culture surfaces is a common problem and presents technical limitations to the design of experiments. To overcome this problem, various surface coating protocols have been developed. However, a comparative and precise real-time measurement of their impact on cell behavior has not been conducted. The prostate cancer cell line LNCaP, derived from a patient lymph node metastasis, is a commonly used model system in prostate cancer research. However, the cells’ characteristically weak attachment to the surface of tissue culture vessels and cover slips has impeded their manipulation and analysis and use in high throughput screening. To improve the adherence of LNCaP cells to the culture surface, we compared different coating reagents (poly-l-lysine, poly-l-ornithine, collagen type IV, fibronectin, and laminin) and culturing conditions and analyzed their impact on cell proliferation, adhesion, morphology, mobility and gene expression using real-time technologies. The results showed that fibronectin, poly-l-lysine and poly-l-ornithine improved LNCaP cells adherence and provoked cell morphology alterations, such as increase of nuclear and cellular area. These coating reagents also induced a higher expression of F-actin and reduced cell mobility. In contrast, laminin and collagen type IV did not improve adherence but promoted cell aggregation and affected cell morphology. Cells cultured in the presence of laminin displayed higher mobility than control cells. All the coating conditions significantly affected cell viability; however, they did not affect the expression of androgen receptor-regulated genes. Our comparative findings provide important insight for the selection of the ideal coating reagent and culture conditions for the cancer cell lines with respect to their effect on proliferation rate, attachment, morphology, migration, transcriptional response and cellular cytoskeleton arrangement. PMID:25375165

Guide to the Internet. The world wide web.

PubMed Central

Pallen, M.

1995-01-01

The world wide web provides a uniform, user friendly interface to the Internet. Web pages can contain text and pictures and are interconnected by hypertext links. The addresses of web pages are recorded as uniform resource locators (URLs), transmitted by hypertext transfer protocol (HTTP), and written in hypertext markup language (HTML). Programs that allow you to use the web are available for most operating systems. Powerful on line search engines make it relatively easy to find information on the web. Browsing through the web--"net surfing"--is both easy and enjoyable. Contributing to the web is not difficult, and the web opens up new possibilities for electronic publishing and electronic journals. Images p1554-a Fig 5 PMID:8520402

Electrodeposited MCrAlY Coatings for Gas Turbine Engine Applications

NASA Astrophysics Data System (ADS)

Zhang, Y.

2015-11-01

Electrolytic codeposition is a promising alternative process for fabricating MCrAlY coatings. The coating process involves two steps, i.e., codeposition of CrAlY-based particles and a metal matrix of Ni, Co, or (Ni,Co), followed by a diffusion heat treatment to convert the composite coating to the desired MCrAlY microstructure. Despite the advantages such as low cost and non-line-of-sight, this coating process is less known than electron beam-physical vapor deposition and thermal spray processes for manufacturing high-temperature coatings. This article provides an overview of the electro-codeposited MCrAlY coatings for gas turbine engine applications, highlighting the unique features of this coating process and some important findings in the past 30 years. Challenges and research opportunities for further optimization of this type of MCrAlY coatings are also discussed.

A new pulsed laser deposition technique: scanning multi-component pulsed laser deposition method.

PubMed

Fischer, D; de la Fuente, G F; Jansen, M

2012-04-01

The scanning multi-component pulsed laser deposition (PLD) method realizes uniform depositions of desired coatings by a modified pulsed laser deposition process, preferably with a femto-second laser-system. Multi-component coatings (single or multilayered) are thus deposited onto substrates via laser induced ablation of segmented targets. This is achieved via horizontal line-scanning of a focused laser beam over a uniformly moving target's surface. This process allows to deposit the desired composition of the coating simultaneously, starting from the different segments of the target and adjusting the scan line as a function of target geometry. The sequence and thickness of multilayers can easily be adjusted by target architecture and motion, enabling inter/intra layer concentration gradients and thus functional gradient coatings. This new, simple PLD method enables the achievement of uniform, large-area coatings. Case studies were performed with segmented targets containing aluminum, titanium, and niobium. Under the laser irradiation conditions applied, all three metals were uniformly ablated. The elemental composition within the rough coatings obtained was fixed by the scanned area to Ti-Al-Nb = 1:1:1. Crystalline aluminum, titanium, and niobium were found to coexist side by side at room temperature within the substrate, without alloy formation up to 600 °C. © 2012 American Institute of Physics

Trace Metal Associations with Manganese-Rich Surface Coatings of Lead Service Lines

EPA Science Inventory

Analysis of lead service line samples from U. S. Environmental Protection Agency’s long-term research program to evaluate control and metal release from domestic drinking water service lines has revealed that Manganese-rich solids also contain Iron and sometimes Aluminum have fre...

Low cost solar array project: Cell and module formation research area. Process research of non-CZ silicon material

NASA Technical Reports Server (NTRS)

1983-01-01

Meniscus coates tests, back junction formation using a new boron containing liquid, tests of various SiO2 and boron containing liquids, pelletized silicon for replenishment during web growth, and ion implantation compatibility/feasibility study are discussed.

40 CFR 63.4311 - What reports must I submit?

Code of Federal Regulations, 2010 CFR

2010-07-01

...-on controls, or the organic HAP overall control efficiency compliance option for web coating/printing... emission rate with add-on controls option, the organic HAP overall control efficiency option, or the oxidizer outlet organic HAP concentration option and there were no periods during which the continuous...

Paper and Other Web Coating National Emission Standards for Hazardous Air Pollutants (NESHAP): Applicability Determination Memo

EPA Pesticide Factsheets

This November 2003 memo indicates that size presses or size press alternative (SP/SPA), and on-machine coaters that apply sizing or water-based clays as a component of papermaking system are not subject to requirement of Subpart JJJJ.

40 CFR 63.3320 - What emission standards must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true What emission standards must I meet? 63... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating Emission Standards...

Highly efficient blazed grating with multilayer coating for tender X-ray energies.

PubMed

Senf, F; Bijkerk, F; Eggenstein, F; Gwalt, G; Huang, Q; Kruijs, R; Kutz, O; Lemke, S; Louis, E; Mertin, M; Packe, I; Rudolph, I; Schäfers, F; Siewert, F; Sokolov, A; Sturm, J M; Waberski, Ch; Wang, Z; Wolf, J; Zeschke, T; Erko, A

2016-06-13

For photon energies of 1 - 5 keV, blazed gratings with multilayer coating are ideally suited for the suppression of stray and higher orders light in grating monochromators. We developed and characterized a blazed 2000 lines/mm grating coated with a 20 period Cr/C- multilayer. The multilayer d-spacing of 7.3 nm has been adapted to the line distance of 500 nm and the blaze angle of 0.84° in order to provide highest efficiency in the photon energy range between 1.5 keV and 3 keV. Efficiency of the multilayer grating as well as the reflectance of a witness multilayer which were coated simultaneously have been measured. An efficiency of 35% was measured at 2 keV while a maximum efficiency of 55% was achieved at 4 keV. In addition, a strong suppression of higher orders was observed which makes blazed multilayer gratings a favorable dispersing element also for the low X-ray energy range.

Corrosion study of bare and coated stainless steel

NASA Technical Reports Server (NTRS)

Morrison, J. D.

1972-01-01

A program was conducted at Kennedy Space Center from February 1968 to February 1971 to evaluate the performance of austenitic stainless steel alloys used in fluid systems lines. For several years, there had been numerous failures of stainless steel hardware caused by pitting and stress corrosion cracking. Several alloys were evaluated for effectiveness of certain sacrificial-type protective coverings in preventing corrosion failures. Samples were tested in specially designed racks placed 91 meters (100 yards) above high-tide line at Cape Kennedy. It is concluded that: (1) unprotected tubing samples showed evidence of pitting initiation after 2 weeks; (2) although some alloys develop larger pits than others, it is probable that the actual pitting rate is independent of alloy type; (3) the deepest pitting occurred in the sheltered part of the samples; and (4) zinc-rich coatings and an aluminum-filled coating have afforded sacrificial protection against pitting for at least 28 months. It is believed that a much longer effective coating life can be expected.

Low surface energy polymeric release coating for improved contact print lithography

NASA Astrophysics Data System (ADS)

Mancini, David P.; Resnick, Douglas J.; Gehoski, Kathleen A.; Popovich, Laura L.; Chang, Daniel

2002-03-01

Contact printing has been used for decades in many various lithography applications in the microelectronic industry. While vacuum contact printing processes offer sub-micron resolution and high throughput, they often suffer from some important drawbacks. One of the most common problems is degradation in both resolution and defect density which occurs when the same mask si used for multiple exposures without frequent mask cleans. This is largely due to the relatively high surface energy of both quartz and chrome and the tendency of most photoresists to adhere to these surfaces. As a result, when a mask and wafer are pressed into intimate contact, resist will tend to stick to the mask creating a defect on the wafer, effectively propagating defects to subsequent wafers. In this study, DuPont Teflon AF 1601S is used as a photomask coating and evaluated for its ability to act as a release agent and reduce defects while maintaining resolution for multiple exposures. Teflon AF is an amorphous, transparent, low surface energy, polymeric material that can be spin coated into a thin conformal film. Tests have shown that when using an uncoated mask in vacuum contact, resolution of 0.75 micrometers dense lines is severely degraded after less than 10 consecutive exposures. However, when the mask is coated, 0.75 micrometers dense lines were successfully resolved using vacuum contact for over 200 exposures without cleaning. In addition, it has been demonstrated that Teflon AF coatings impart to a mask a self-cleaning capability, since particles tend to stick to the photoresist rather than the mask. A coated mask, which was purposefully contaminated with particulates, resolved 0.75 micrometers dense lines on all but the first wafer of a series of 25 consecutive exposures. The patented mask releases layer process has successfully been demonstrated with a positive novolak resist. Additional data which describes the system chemistry, dilution and coating process, and film morphology are also presented.

"Ask a slave" and interpreting race on public history's front line: interview with Azie Mira Dungey.

PubMed

Dungey, Azie Mira; Tyson, Amy M

2014-02-01

In this interview, Azie Mira Dungey (creator of the web series, "Ask a Slave") and Amy M. Tyson (Associate Professor of History at DePaul University and author of The Wages of History: Emotional Labor on Public History's Front Lines) discuss Dungey's web series, as well as her experiences as a living history interpreter at both the Smithsonian Museum of American History and at Mount Vernon.

Drying of fiber webs

DOEpatents

Warren, D.W.

1997-04-15

A process and an apparatus are disclosed for high-intensity drying of fiber webs or sheets, such as newsprint, printing and writing papers, packaging paper, and paperboard or linerboard, as they are formed on a paper machine. The invention uses direct contact between the wet fiber web or sheet and various molten heat transfer fluids, such as liquefied eutectic metal alloys, to impart heat at high rates over prolonged durations, in order to achieve ambient boiling of moisture contained within the web. The molten fluid contact process causes steam vapor to emanate from the web surface, without dilution by ambient air; and it is differentiated from the evaporative drying techniques of the prior industrial art, which depend on the uses of steam-heated cylinders to supply heat to the paper web surface, and ambient air to carry away moisture, which is evaporated from the web surface. Contact between the wet fiber web and the molten fluid can be accomplished either by submersing the web within a molten bath or by coating the surface of the web with the molten media. Because of the high interfacial surface tension between the molten media and the cellulose fiber comprising the paper web, the molten media does not appreciatively stick to the paper after it is dried. Steam generated from the paper web is collected and condensed without dilution by ambient air to allow heat recovery at significantly higher temperature levels than attainable in evaporative dryers. 6 figs.

Using the World Wide Web for GIDEP Problem Data Processing at Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

McPherson, John W.; Haraway, Sandra W.; Whirley, J. Don

1999-01-01

Since April 1997, Marshall Space Flight Center has been using electronic transfer and the web to support our processing of the Government-Industry Data Exchange Program (GIDEP) and NASA ALERT information. Specific aspects include: (1) Extraction of ASCII text information from GIDEP for loading into Word documents for e-mail to ALERT actionees; (2) Downloading of GIDEP form image formats in Adobe Acrobat (.pdf) for internal storage display on the MSFC ALERT web page; (3) Linkage of stored GRDEP problem forms with summary information for access from the MSFC ALERT Distribution Summary Chart or from an html table of released MSFC ALERTs (4) Archival of historic ALERTs for reference by GIDEP ID, MSFC ID, or MSFC release date; (5) On-line tracking of ALERT response status using a Microsoft Access database and the web (6) On-line response to ALERTs from MSFC actionees through interactive web forms. The technique, benefits, effort, coordination, and lessons learned for each aspect are covered herein.

Transport of poly(acrylic acid) coated 2-line ferrihydrite nanoparticles in saturated aquifer sediments for environmental remediation

NASA Astrophysics Data System (ADS)

Xiang, Aishuang; Zhou, Sheng; Koel, Bruce E.; Jaffé, Peter R.

2014-04-01

Groundwater remediation using iron oxide and zero-valent iron nanoparticles (NPs) can be effective, but is limited in many applications due to the NP strong retention in groundwater-saturated porous media after injection, the passivation of the porous surface, and the high cost of nanomaterials versus macro scale iron. In this study, we investigated transport of bare and polymer-coated 2-line ferrihydrite NPs (30-300 nm) in saturated aquifer sediments. The influence of poly(acrylic acid) (PAA) polymer coatings was studied on the colloidal stability and transport in sediments packed column tests simulating groundwater flow in saturated sediments. In addition, the influence of calcium cations was investigated by transport measurements using sediments with calcium concentrations in the aqueous phase ranging from 0.5 (typical for most sediments) to 2 mM. Measurements were also made of zeta potential, hydrodynamic diameter, polymer adsorption and desorption properties, and bio-availability of PAA-coated NPs. We found that NP transport through the saturated aquifer sediments was improved by PAA coating and that the transport properties could be tuned by adjusting the polymer concentration. We further discovered that PAA coatings enhanced NP transport, compared to bare NPs, in all calcium-containing experiments tested, however, the presence of calcium always exhibited a negative effect on NP transport. In tests of bioavailability, the iron reduction rate of the coated and bare NPs by Geobacter sulfurreducens was the same, which shows that the PAA coating does not significantly reduce NP Fe(III) bioavailability. Our results demonstrate that much improved transport of iron oxide NP can be achieved in saturated aquifer sediments by introducing negatively charged polyelectrolytes and optimizing polymer concentrations, and furthermore, these coated NPs retain their bioavailability that is needed for applications in bio-environmental remediation.

WebWatcher: Machine Learning and Hypertext

DTIC Science & Technology

1995-05-29

WebWatcher: Machine Learning and Hypertext Thorsten Joachims, Tom Mitchell, Dayne Freitag, and Robert Armstrong School of Computer Science Carnegie...HTML-page about machine learning in which we in- serted a hyperlink to WebWatcher (line 6). The user follows this hyperlink and gets to a page which...AND SUBTITLE WebWatcher: Machine Learning and Hypertext 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... from the web coating/printing operation surfaces they are applied to occurs within the capture system... system efficiency? 63.4361 Section 63.4361 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... emission capture system efficiency? You must use the procedures and test methods in this section to...

40 CFR 63.3400 - What notifications and reports must I submit?

Code of Federal Regulations, 2011 CFR

2011-07-01

... National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating Notifications... under § 63.9(b), provided the same information is contained in the permit application as required by... compliance report must contain the information in paragraphs (c)(2)(i) through (vi) of this section: (i...

40 CFR 63.3400 - What notifications and reports must I submit?

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating... under § 63.9(b), provided the same information is contained in the permit application as required by... compliance report must contain the information in paragraphs (c)(2)(i) through (vi) of this section: (i...

40 CFR 63.3400 - What notifications and reports must I submit?

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating... under § 63.9(b), provided the same information is contained in the permit application as required by... compliance report must contain the information in paragraphs (c)(2)(i) through (vi) of this section: (i...

40 CFR 63.3320 - What emission standards must I meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true What emission standards must I meet? 63... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Hazardous Air Pollutants: Paper and Other Web Coating Emission Standards and Compliance Dates...

Best Practices in Supporting Persistence of Distant Education Students through Integrated Web-Based Systems

ERIC Educational Resources Information Center

McCracken, Holly

2009-01-01

The importance of the interconnectedness of academic, student, and technical support processes intrinsic to the provision of on-line instruction has been frequently depicted as a "service Web," with students at the center of the infrastructure. However, as programming to support distance learning continues to develop, such service Webs have grown…

Pre-Service Teachers Critically Evaluate Scientific Information on the World-Wide Web: What Makes Information Believable?

ERIC Educational Resources Information Center

Iding, Marie; Klemm, E. Barbara

2005-01-01

The present study addresses the need for teachers to critically evaluate the credibility, validity, and cognitive load associated with scientific information on Web sites, in order to effectively teach students to evaluate scientific information on the World Wide Web. A line of prior research investigating high school and university students'…

A Checklist for Designing and Evaluating Physical Education Program Web Sites

ERIC Educational Resources Information Center

Tucker, Michael; Hill, Grant

2009-01-01

Creating a physical education department web site is an excellent way to promote a positive image of the program, because students and parents are able to find important information and improve the lines of communication. A well-designed physical education web site can even encourage students to increase their physical activity levels. Improved…

Accessibility of School Districts' Web Sites: A Descriptive Study

ERIC Educational Resources Information Center

Bray, Marty; Flowers, Claudia; Gibson, Patricia

2003-01-01

Many school districts (SDs) use the World Wide Web (WWW or Web) to disseminate a wide variety of information about things such as district events, policies, and a wide variety of student information. On-line barriers limit the accessibility of the WWW for persons and students with disabilities and thus can limit their access to vital information.…

FASTQ quality control dashboard

DOE Office of Scientific and Technical Information (OSTI.GOV)

2016-07-25

FQCDB builds up existing open source software, FastQC, implementing a modern web interface for across parsed output of FastQC. In addition, FQCDB is extensible as a web service to include additional plots of type line, boxplot, or heatmap, across data formatted according to guidelines. The interface is also configurable via more readable JSON format, enabling customization by non-web programmers.

The Business Information Services: Old-Line Online Moves to the Web.

ERIC Educational Resources Information Center

O'Leary, Mick

1997-01-01

Although the availability of free information on the World Wide Web has placed traditional, fee-based proprietary online services on the defensive, most major online business services are now on the Web. Highlights several business information providers: Profound, NewsNet and ProQuest Direct, Dow Jones and Wall Street Journal Interactive Edition,…

49 CFR 190.11 - Availability of informal guidance and interpretive assistance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... established a Web site and a telephone line to OPS headquarters where information on and advice about compliance with the pipeline safety regulations specified in 49 CFR parts 190-199 is available. The Web site..., individuals may leave a recorded voicemail message or post a message on the OPS Web site. The telephone number...

Replacement for a Flex Hose Coating at the Space Shuttle Launch Pad

NASA Technical Reports Server (NTRS)

Whitten, Mary; Vinje, Rubiela; Curran, Jerome; Meneghelli, Barry; Calle, Luz Marina

2009-01-01

Aerocoat AR-7 is a coating that has been used to protect stainless steel flex hoses at NASA's Kennedy Space Center launch complex and hydraulic lines of the mobile launch platform (MLP). This coating has great corrosion control performance and low temperature application. AR-7 was developed by NASA and produced exclusively for NASA but its production has been discontinued due to its high content of volatile organic compounds (VOC) and significant environmental impact. The purpose of this project was to select and evaluate candidate coatings to find a replacement coating that is more environmentally friendly, with similar properties to AR-7. No coatings were identified that perform the same as AR-7 in all areas. Candidate coatings failed in comparison to AR-7 in salt fog, beachside atmospheric exposure, pencil hardness, Mandrel bend, chemical compatibility, adhesion, and ease of application tests. However, two coatings were selected for further evaluation.

Community LINE Source Model (C-LINE)

EPA Science Inventory

This presentation provides an introduction for the live demo and explains the purpose of C-LINE and its key features. C-LINE is a web-based model designed to inform the community user of local air quality impacts due to mobile-sources in their region of interest using a simplifie...

Plasma-sprayed titanium coating to polyetheretherketone improves the bone-implant interface.

PubMed

Walsh, William R; Bertollo, Nicky; Christou, Chrisopher; Schaffner, Dominik; Mobbs, Ralph J

2015-05-01

Rapid and stable fixation at the bone-implant interface would be regarded as one of the primary goals to achieve clinical efficacy, regardless of the surgical site. Although mechanical and physical properties of polyetheretherketone (PEEK) provide advantages for implant devices, the hydrophobic nature and the lack of direct bone contact remains a limitation. To examine the effects of a plasma-sprayed titanium coated PEEK on the mechanical and histologic properties at the bone-implant interface. A preclinical laboratory study. Polyetheretherketone and plasma-sprayed titanium coated PEEK implants (Ti-bond; Spinal Elements, Carlsbad, CA, USA) were placed in a line-to-line manner in cortical bone and in a press-fit manner in cancellous bone of adult sheep using an established ovine model. Shear strength was assessed in the cortical sites at 4 and 12 weeks, whereas histology was performed in cortical and cancellous sites at both time points. The titanium coating dramatically improved the shear strength at the bone-implant interface at 4 weeks and continued to improve with time compared with PEEK. Direct bone ongrowth in cancellous and cortical sites can be achieved using a plasma-sprayed titanium coating on PEEK. Direct bone to implant bonding can be achieved on PEEK in spite of its hydrophobic nature using a plasma-sprayed titanium coating. The plasma-sprayed titanium coating improved mechanical properties in the cortical sites and the histology in cortical and cancellous sites. Copyright © 2015 Elsevier Inc. All rights reserved.

40 CFR 63.5170 - How do I demonstrate compliance with the standards?

Code of Federal Regulations, 2011 CFR

2011-07-01

... for individual or groups of coil coating lines; or overall organic HAP control efficiency is at least... compliant coatings and control devices and maintaining an acceptable equivalent emission rate Average... facility. (6) Control efficiency calculation of HAP emitted. For each work station or group of work...

40 CFR 63.5170 - How do I demonstrate compliance with the standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... for individual or groups of coil coating lines; or overall organic HAP control efficiency is at least... compliant coatings and control devices and maintaining an acceptable equivalent emission rate Average... facility. (6) Control efficiency calculation of HAP emitted. For each work station or group of work...

Cryogenic-temperature profiling of high-power superconducting lines using local and distributed optical-fiber sensors.

PubMed

Chiuchiolo, Antonella; Palmieri, Luca; Consales, Marco; Giordano, Michele; Borriello, Anna; Bajas, Hugues; Galtarossa, Andrea; Bajko, Marta; Cusano, Andrea

2015-10-01

This contribution presents distributed and multipoint fiber-optic monitoring of cryogenic temperatures along a superconducting power transmission line down to 30 K and over 20 m distance. Multipoint measurements were conducted using fiber Bragg gratings sensors coated with two different functional overlays (epoxy and poly methyl methacrylate (PMMA)) demonstrating cryogenic operation in the range 300-4.2 K. Distributed measurements exploited optical frequency-domain reflectometry to analyze the Rayleigh scattering along two concatenated fibers with different coatings (acrylate and polyimide). The integrated system has been placed along the 20 m long cryostat of a superconducting power transmission line, which is currently being tested at the European Organization for Nuclear Research (CERN). Cool-down events from 300-30 K have been successfully measured in space and time, confirming the viability of these approaches to the monitoring of cryogenic temperatures along a superconducting transmission line.

5 CFR 1640.6 - Methods of providing information.

Code of Federal Regulations, 2010 CFR

2010-01-01

... part to participants by making it available on the TSP Web site. A participant can request paper copies of that information from the TSP by calling the ThriftLine, submitting a request through the TSP Web...

The 10 Hottest Technologies in Telecom.

ERIC Educational Resources Information Center

Flanagan, Patrick

1997-01-01

Presents the fourth annual listing of the 10 "hottest" telecommunications technologies. Describes Web broadcasting, remote-access servers, extranets, Internet telephony, enterprise network directory services, Web site management tools, IP (Internet Protocols) switching, wavelength division multiplexing, digital subscriber lines, and…

5 CFR 1640.6 - Methods of providing information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... part to participants by making it available on the TSP Web site. A participant can request paper copies of that information from the TSP by calling the ThriftLine, submitting a request through the TSP Web...

5 CFR 1640.6 - Methods of providing information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... part to participants by making it available on the TSP Web site. A participant can request paper copies of that information from the TSP by calling the ThriftLine, submitting a request through the TSP Web...

Clustergrammer, a web-based heatmap visualization and analysis tool for high-dimensional biological data

PubMed Central

Fernandez, Nicolas F.; Gundersen, Gregory W.; Rahman, Adeeb; Grimes, Mark L.; Rikova, Klarisa; Hornbeck, Peter; Ma’ayan, Avi

2017-01-01

Most tools developed to visualize hierarchically clustered heatmaps generate static images. Clustergrammer is a web-based visualization tool with interactive features such as: zooming, panning, filtering, reordering, sharing, performing enrichment analysis, and providing dynamic gene annotations. Clustergrammer can be used to generate shareable interactive visualizations by uploading a data table to a web-site, or by embedding Clustergrammer in Jupyter Notebooks. The Clustergrammer core libraries can also be used as a toolkit by developers to generate visualizations within their own applications. Clustergrammer is demonstrated using gene expression data from the cancer cell line encyclopedia (CCLE), original post-translational modification data collected from lung cancer cells lines by a mass spectrometry approach, and original cytometry by time of flight (CyTOF) single-cell proteomics data from blood. Clustergrammer enables producing interactive web based visualizations for the analysis of diverse biological data. PMID:28994825

Neural Network Substorm Identification: Enabling TREx Sensor Web Modes

NASA Astrophysics Data System (ADS)

Chaddock, D.; Spanswick, E.; Arnason, K. M.; Donovan, E.; Liang, J.; Ahmad, S.; Jackel, B. J.

2017-12-01

Transition Region Explorer (TREx) is a ground-based sensor web of optical and radio instruments that is presently being deployed across central Canada. The project consists of an array of co-located blue-line, full-colour, and near-infrared all-sky imagers, imaging riometers, proton aurora spectrographs, and GNSS systems. A key goal of the TREx project is to create the world's first (artificial) intelligent sensor web for remote sensing space weather. The sensor web will autonomously control and coordinate instrument operations in real-time. To accomplish this, we will use real-time in-line analytics of TREx and other data to dynamically switch between operational modes. An operating mode could be, for example, to have a blue-line imager gather data at a one or two orders of magnitude higher cadence than it operates for its `baseline' mode. The software decision to increase the imaging cadence would be in response to an anticipated increase in auroral activity or other programmatic requirements. Our first test for TREx's sensor web technologies is to develop the capacity to autonomously alter the TREx operating mode prior to a substorm expansion phase onset. In this paper, we present our neural network analysis of historical optical and riometer data and our ability to predict an optical onset. We explore the preliminary insights into using a neural network to pick out trends and features which it deems are similar among substorms.

Advances in far-ultraviolet reflective and transmissive coatings for space applications

NASA Astrophysics Data System (ADS)

Rodríguez-de Marcos, Luis; Aznárez, José A.; Méndez, José A.; Larruquert, Juan I.; Vidal-Dasilva, M.; Malvezzi, A. Marco; Giglia, Angelo; Capobianco, Gerardo; Massone, Giuseppe; Fineschi, Silvano; Nannarone, Stefano

2016-07-01

Exploitation of far ultraviolet (FUV, 100-200 nm) observations extends to most areas of modern astronomy, from detailed observations of Solar System objects, the interstellar medium, exoplanets, stars and galaxies, to studies of crucial cosmological relevance. Despite several developments in recent decades, yet many observations are not possible due to technical limitations, of which one of the most important is the lack of optical coatings with high throughput. Development and optimization of such efficient FUV coatings have been identified in several roadmap reports as a key goal for future missions. The success of this development will ultimately improve the performance of nowadays feasible optical instruments and will enable new scientific imaging capabilities. GOLD's research is devoted to developing novel coatings with enhanced performance for space optics. Several deposition systems are available for the deposition of multilayer coatings. A deposition system was developed to deposit FUV coatings to satisfy space requirements. It consists of a 75-cm-diameter deposition chamber pumped with a cryo-pump and placed in an ISO-6 clean room. This chamber is available for deposition by evaporation of top-requirement coatings such as Al/ MgF2 mirrors or (Al/MgF2)n multilayer coatings for transmittance filters. A plan to add an Ion-Beam-Sputtering system in this chamber is under way. In this and other chambers at GOLD the following FUV coatings can be prepared: Transmittance filters based on (Al/MgF2)n multilayer coatings. These filters can be designed to have a peak at the FUV spectral line or band of interest and a high peak-to-visible transmittance ratio. Filters can be designed with a peak transmittance at a wavelength as short as 120 nm and with a transmittance in the visible smaller than 10-5. Narrowband reflective coatings peaked close to H Lyman β (102.6 nm) with a reflectance at H Lyman α (121.6 nm) two orders of magnitude below the one at 102.6 nm. Other potential spectral lines at which these coatings could be peaked are the OVI doublet (103.2, 103.8 nm). Narrowband reflective mirrors based on (MgF2/LaF3)n multilayers peaked at a wavelength as short as 120 nm. Target wavelengths include lines of high interest for space observations, such as H Lyman α (121.6 nm), OI (130.4 and 135.6 nm), CIV (154.8, 155.1 nm), among others. Coating-based linear polarizers tuned at H Lyman α (121.6 nm) both based on reflectance or on transmittance. Reflective polarizers present a high efficiency. Transmissive polarizers have a more modest peak performance compared to reflective polarizers; however, they involve spectral filtering properties to reject the long FUV and even more the near UV to the IR, which turn them competitive compared to reflective polarizers. In this communication we present a summary of our research on the above FUV coatings developed at GOLD.

4 Metre diameter penstock construction for the Raymond Reservoir Hydro Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, H.D.; Alexander, M.

1995-12-31

A four metre diameter 770 m long buried steel penstock was constructed for the 20 MW Raymond Reservoir Hydro Project in southern Alberta. The penstock delivers up to 56.7 m{sup 3}/sec of irrigation water at an effective head of 44 m to a 2.6 m diameter Kaplan turbine. The hydro facility was commissioned in the spring of 1994. The steel pipe was delivered to the site in 18 m long sections from a fabrication plant located 250 km away. Specialized equipment was engineered and constructed to externally coat and internally line the pipe sections on site. The pipe sections, weighingmore » from 27,000 to 30,000 kg, were rolled and moved on a specially built lathe during the external sandblasting and tape wrapping operation. The external tape wrapping is one element of the cathodic protection system for the steel pipe. Specialized equipment was modified to sandblast the interior to white metal and then mechanically apply three coats of internal epoxy lining. The internal lining improves the hydraulic characteristics of the pipe in addition to protecting the pipe from corrosion. This innovative approach to coating and lining the pipe resulted in an exceptionally high quality product at an affordable cost.« less

Vincristine-sulphate-loaded liposome-templated calcium phosphate nanoshell as potential tumor-targeting delivery system.

PubMed

Thakkar, Hetal Paresh; Baser, Amit Kumar; Parmar, Mayur Prakashbhai; Patel, Ketul Harshadbhai; Ramachandra Murthy, Rayasa

2012-06-01

Vincristine-sulfate-loaded liposomes were prepared with an aim to improve stability, reduce drug leakage during systemic circulation, and increase intracellular uptake. Liposomes were prepared by the thin-film hydration method, followed by coating with calcium phosphate, using the sequential addition approach. Prepared formulations were characterized for size, zeta potential, drug-entrapment efficiency, morphology by transmission electron microscopy (TEM), in vitro drug-release profile, and in vitro cell cytotoxicity study. Effect of formulation variables, such as drug:lipid ratio as well as nature and volume of hydration media, were found to affect drug entrapment, and the concentration of calcium chloride in coating was found to affect size and coating efficiency. Size, zeta potential, and TEM images confirmed that the liposomes were effectively coated with calcium phosphate. The calcium phosphate nanoshell exhibited pH-dependent drug release, showing significantly lower release at pH 7.4, compared to the release at pH 4.5, which is the pH of the tumor interstitium. The in vitro cytotoxicity study done on the lung cancer cell line indicated that coated liposomes are more cytotoxic than plain liposomes and drug solution, indicating their potential for intracellular drug delivery. The cell-uptake study done on the lung cancer cell line indicated that calcium-phosphate-coated liposomes show higher cell uptake than uncoated liposomes.

Low Contribution of PbO 2 -Coated Lead Service Lines to Water Lead Contamination at the Tap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Triantafyllidou, Simoni; Schock, Michael R.; DeSantis, Michael K.

2015-02-24

To determine if residential water sampling corroborates the expectation that formation of stable PbO2 coatings on lead service lines (LSLs) provides an effective lead release control strategy, lead profile sampling was evaluated for eight home kitchen taps in three U.S. cities with observed PbO2-coated LSLs (Newport, Rhode Island; Cincinnati and Oakwood, Ohio). After various water standing times, these LSLs typically released similar or lower peak lead levels (1 to 18 μg/L) than the lead levels from the respective kitchen faucets (1 to 130 μg/L), and frequently 50–80% lower than the lead levels typically reported from Pb(II)-coated LSLs in comparable publishedmore » sampling studies. Prolonged stagnation (10–101 h) at the Cincinnati sites produced varying results. One site showed minimal (0–4 μg/L) increase in lead release from the PbO2-coated LSL, and persistence of free chlorine residual. However, the other site showed up to a 3-fold increase proportional to standing time, with essentially full depletion of the chlorine residual. Overall, lead release was consistently much lower than that reported in studies of Pb(II)-coated LSL scales, suggesting that natural formation of PbO2 in LSLs is an effective lead “corrosion” control strategy.« less

Redox-responsive microbeads containing thiolated pectin-doxorubicin conjugate inhibit tumor growth and metastasis: An in vitro and in vivo study.

PubMed

Cheewatanakornkool, Kamonrak; Niratisai, Sathit; Dass, Crispin R; Sriamornsak, Pornsak

2018-07-10

The objective of this study was to investigate the in vitro cytotoxicity and in vivo anticancer efficacy of redox-responsive microbeads containing thiolated pectin-doxorubicin (DOX) conjugate. Oral microbeads were coated with an enteric polymer to protect the drug from release in the upper gastrointestinal (GI) tract and allow redox-triggered drug release in the colon. Morphology, particle size, drug content, and in vitro drug release behavior of the microbeads were characterized; in vitro cytotoxicity was tested on mouse colon carcinoma, human colorectal adenocarcinoma, and human bone osteosarcoma cell lines. In vivo anticancer efficacy of coated microbeads was examined in BALB/c mice with murine colon carcinoma. These coated microbeads significantly inhibited the growth of all cell lines. The in vivo study confirmed delivery of DOX to the colorectal tumor site, redox-responsiveness, and anticancer efficacy of coated microbeads. Coated microbeads also effectively inhibited primary tumor growth and suppressed tumor metastases without gross toxicity to the non-target tissue. No noticeable damage was found in mouse GI tissues, indicating lack of DOX toxicity. These novel coated microbeads containing thiolated pectin-DOX conjugate may be a promising vehicle for targeted clinical delivery of DOX to the colorectal cancer site by oral administration. Crown Copyright © 2018. Published by Elsevier B.V. All rights reserved.

Characterization, Corrosion Resistance, and Cell Response of High-Velocity Flame-Sprayed HA and HA/TiO2 Coatings on 316L SS

NASA Astrophysics Data System (ADS)

Singh, Tejinder Pal; Singh, Harpreet; Singh, Hazoor

2012-09-01

The main aim of this study is to evaluate corrosion and biocompatibility behavior of thermal spray hydroxyapatite (HA) and hydroxyapatite/titania bond (HA/TiO2)-coated 316L stainless steel (316L SS). In HA/TiO2 coatings, TiO2 was used as a bond coat between HA top coat and 316L SS substrate. The coatings were characterized by x-ray diffraction and scanning electron microscopy/energy dispersive spectroscopy, and corrosion resistance determined for the uncoated substrate and the two coatings. The biological behavior was investigated by the cell culture studies using osteosarcoma cell line KHOS-NP (R-970-5). The corrosion resistance of the steel was found to increase after the deposition of the HA and HA/TiO2 bond coatings. Both HA, as well as, HA/TiO2 coatings exhibit excellent bond strength of 49 and 47 MPa, respectively. The cell culture studies showed that HA-coated 316L SS specimens appeared more biocompatible than the uncoated and HA/TiO2-coated 316L SS specimens.

Characterization of surface modified polyester fabric.

PubMed

Joseph, Roy; Shelma, R; Rajeev, A; Muraleedharan, C V

2009-12-01

Woven polyethylene terephthalate (PET) fabric has been used in the construction of vascular grafts and sewing ring of prosthetic heart valves. In an effort to improve haemocompatibility and tissue response to PET fabric, a fluoropolymer, polyvinylidine fluoride (PVDF), was coated on PET fabric by dip coating technique. The coating was found to be uniform and no significant changes occurred on physical properties such as water permeability and burst strength. Cell culture cytotoxicity studies showed that coated PET was non-cytotoxic to L929 fibroblast cell lines. In vitro studies revealed that coating improved haemocompatibility of PET fabric material. Coating reduced platelet consumption of PET fabric by 50%. Upon surface modification leukocyte consumption of PET was reduced by 24%. About 60% reduction in partial thromboplastin time (PTT) observed when PET was coated with PVDF. Results of endothelial cell proliferation studies showed that surface coating did not have any substantial impact on cell proliferation. Overall results indicate that coating has potential to improve haemocompatibility of PET fabric without affecting its mechanical performance.

The World Wide Web and Chemistry Books On Line

ERIC Educational Resources Information Center

Palmer, W. P.

1997-01-01

This paper illustrates the educational uses of the Word Wide Web in a university situation; it gives an account some of the ways in which the World Wide Web and other information technologies have been used to extend the scope of the history of science generally and the history of chemistry in particular. I observed that the World Wide Web…

Web Survey Design in ASP.Net 2.0: A Simple Task with One Line of Code

ERIC Educational Resources Information Center

Liu, Chang

2007-01-01

Over the past few years, more and more companies have been investing in electronic commerce (EC) by designing and implementing Web-based applications. In the world of practice, the importance of using Web technology to reach individual customers has been presented by many researchers. This paper presents an easy way of conducting marketing…

The Use of Web-Based Portfolios in College Physical Education Activity Courses

ERIC Educational Resources Information Center

Hastie, Peter A.; Sinelnikov, Oleg A.

2007-01-01

This paper describes the introduction of web-based portfolios as a means of authentic assessment in collegiate physical education classes. Students in three volleyball classes were required to contribute to web-based team portfolios, and at the end of the semester, were able to make comment upon this process. A six-item on-line survey used to…

Impact of Web Based Learning on EFL: Using On-Line Discussion Forum (ODF) to Enhance Students' Writing Skill

ERIC Educational Resources Information Center

Akmal

2017-01-01

Web based learning is considered as a breakthrough in the teaching of writing skill to the pre-service teachers at University of PGRI Semarang, Indonesia. The students should write argumentative, persuasive, and descriptive essays. This research offers significant contribution in term of the impact of web based learning on writing skill of English…

E A R T H - S C I E N C E S L I N K S

Science.gov Websites

TSUNAMI! NOAA TSUNAMI Project TSUNAMI Web Site TSUNAMIS in the circum-Pacific Ring of Fire The TSUNAMI DINOSAURS PLATE TECTONICS The Dinosaur Web Pages DINOSAURIA ON-LINE Fossils & Dinosaurs Earth Through opportunities in the earth sciences Geologic Time USGS Learning Web Geoscience Information Center National

Outdoor Programs On-Line: Creating a Link with Participants, Staff and Community.

ERIC Educational Resources Information Center

Poff, Raymond

As use of the Internet and the World Wide Web increases, patrons expect that organizations will utilize the technology, and outdoor programs can benefit from doing so. Web sites can be thought of as miniature information booths containing information an agency wants to make available to the public. Outdoor programs can use the Web for many tasks,…

PROCESS FOR PRODUCTION OF URANIUM

DOEpatents

Crawford, J.W.C.

1959-09-29

A process is described for the production of uranium by the autothermic reduction of an anhydrous uranium halide with an alkaline earth metal, preferably magnesium One feature is the initial reduction step which is brought about by locally bringing to reaction temperature a portion of a mixture of the reactants in an open reaction vessel having in contact with the mixture a lining of substantial thickness composed of calcium fluoride. The lining is prepared by coating the interior surface with a plastic mixture of calcium fluoride and water and subsequently heating the coating in situ until at last the exposed surface is substantially anhydrous.

High-Reflectivity Multi-Layer Coatings for the CLASP Sounding Rocket Project

NASA Technical Reports Server (NTRS)

Narukage, Noriyuki; Kano, Ryohei; Bando, Takamasa; Ishikawa, Ryoko; Kubo, Masahito; Katsukawa, Yukio; Ishikawa, Shin-nosuke; Kobiki, Toshihiko; Giono, Gabriel; Auchere, Frederic;

A Distributed System for Learning Programming On-Line

ERIC Educational Resources Information Center

Verdu, Elena; Regueras, Luisa M.; Verdu, Maria J.; Leal, Jose P.; de Castro, Juan P.; Queiros, Ricardo

2012-01-01

Several Web-based on-line judges or on-line programming trainers have been developed in order to allow students to train their programming skills. However, their pedagogical functionalities in the learning of programming have not been clearly defined. EduJudge is a project which aims to integrate the "UVA On-line Judge", an existing…

Mixed composition materials suitable for vacuum web sputter coating

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Rutledge, Sharon K.; Dever, Joyce A.; Bruckner, Eric J.; Walters, Patricia; Hambourger, Paul D.

1996-01-01

Ion beam sputter deposition techniques were used to investigate simultaneous sputter etching of two component targets so as to produce mixed composition films. Although sputter deposition has been largely confined to metals and metal oxides, at least one polymeric material, poly-tetra-fluorethylene, has been demonstrated to produce sputtered fragments which repolymerize upon deposition to produce a highly cross-linked fluoropolymer resembling that of the parent target Fluoropolymer-filled silicon dioxide and fluoropolymer-filled aluminum oxide coatings have been deposited by means of ion beam sputter coat deposition resulting in films having material properties suitable for aerospace and commercial applications. The addition of fluoropolymer to silicon dioxide films was found to increase the hydrophobicity of the resulting mixed films; however, adding fluoropolymer to aluminum oxide films resulted in a reduction in hydrophobicity, thought to be caused by aluminum fluoride formation.

Uncovering Information Hidden in Web Archives: Glimpse at Web Analysis Building on Data Warehouses; Towards Continuous Web Archiving: First Results and an Agenda for the Future; The Open Video Digital Library; After Migration to an Electronic Journal Collection: Impact on Faculty and Doctoral Students; Who Is Reading On-Line Education Journals? Why? And What Are They Reading?; Report on eLibrary@UBC4: Research, Collaboration and the Digital Library - Visions for 2010.

ERIC Educational Resources Information Center

Rauber, Andreas; Bruckner, Robert M.; Aschenbrenner, Andreas; Witvoet, Oliver; Kaiser, Max; Masanes, Julien; Marchionini, Gary; Geisler, Gary; King, Donald W.; Montgomery, Carol Hansen; Rudner, Lawrence M.; Gellmann, Jennifer S.; Miller-Whitehead, Marie; Iverson, Lee

2002-01-01

These six articles discuss Web archives and Web analysis building on data warehouses; international efforts at continuous Web archiving; the Open Video Digital Library; electronic journal collections in academic libraries; online education journals; and an electronic library symposium at the University of British Columbia. (LRW)

The Planetary Data System Distributed Inventory System

NASA Technical Reports Server (NTRS)

Hughes, J. Steven; McMahon, Susan K.

1996-01-01

The advent of the World Wide Web (Web) and the ability to easily put data repositories on-line has resulted in a proliferation of digital libraries. The heterogeneity of the underlying systems, the autonomy of the individual sites, and distributed nature of the technology has made both interoperability across the sites and the search for resources within a site major research topics. This article will describe a system that addresses both issues using standard Web protocols and meta-data labels to implement an inventory of on-line resources across a group of sites. The success of this system is strongly dependent on the existence of and adherence to a standards architecture that guides the management of meta-data within participating sites.

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2011 CFR

2011-07-01

... determine the mass fraction of TVH liquid input from each regulated material used in the web coating.../printing or dyeing/finishing operation during the capture efficiency test run, kg. TVHi = Mass fraction of... enclosure or building enclosure. The liquid-to-uncaptured-gas protocol compares the mass of liquid TVH in...

40 CFR 63.4371 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... wiper blades. Thus, it includes any cleaning material used in the web coating and printing subcategory... process operation run at atmospheric pressure would be a different operating scenario from the same dyeing process operation run under pressure. Organic HAP content means the mass of organic HAP per mass of solids...

40 CFR 63.4371 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... wiper blades. Thus, it includes any cleaning material used in the web coating and printing subcategory... process operation run at atmospheric pressure would be a different operating scenario from the same dyeing process operation run under pressure. Organic HAP content means the mass of organic HAP per mass of solids...

40 CFR 63.4371 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... wiper blades. Thus, it includes any cleaning material used in the web coating and printing subcategory... process operation run at atmospheric pressure would be a different operating scenario from the same dyeing process operation run under pressure. Organic HAP content means the mass of organic HAP per mass of solids...

40 CFR 63.4371 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... wiper blades. Thus, it includes any cleaning material used in the web coating and printing subcategory... process operation run at atmospheric pressure would be a different operating scenario from the same dyeing process operation run under pressure. Organic HAP content means the mass of organic HAP per mass of solids...

40 CFR 63.4371 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... wiper blades. Thus, it includes any cleaning material used in the web coating and printing subcategory... process operation run at atmospheric pressure would be a different operating scenario from the same dyeing process operation run under pressure. Organic HAP content means the mass of organic HAP per mass of solids...

High Critical Current in Metal Organic Derived YBCO Films

DTIC Science & Technology

2010-10-31

process, particularly in reel-to- reel manufacturing equipment. During Phase I, a “three-step” conversion process was developed to de- convolute the...Task 3. After reaction, the 40-mm web was coated on both sides with a silver layer then slit into eight 4-mm width tapes which were laminated between

46 CFR 164.018-5 - Specifications and standards incorporated by reference.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (August 12, 1970), entitled “Cloth, Drill, Cotton.” (4) Federal Specification CCC-C-443 E (December 2, 1974), entitled “Cloth, Duck, Cotton (Single and Plied Filling Yarns, Flat).” (5) Federal Test Method... MIL-C-17415 E (April 16, 1964), entitled “Cloth, Coated, and Webbing, Inflatable Boat and...

46 CFR 164.018-5 - Specifications and standards incorporated by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (August 12, 1970), entitled “Cloth, Drill, Cotton.” (4) Federal Specification CCC-C-443 E (December 2, 1974), entitled “Cloth, Duck, Cotton (Single and Plied Filling Yarns, Flat).” (5) Federal Test Method... MIL-C-17415 E (April 16, 1964), entitled “Cloth, Coated, and Webbing, Inflatable Boat and...

46 CFR 164.018-5 - Specifications and standards incorporated by reference.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (August 12, 1970), entitled “Cloth, Drill, Cotton.” (4) Federal Specification CCC-C-443 E (December 2, 1974), entitled “Cloth, Duck, Cotton (Single and Plied Filling Yarns, Flat).” (5) Federal Test Method... MIL-C-17415 E (April 16, 1964), entitled “Cloth, Coated, and Webbing, Inflatable Boat and...

46 CFR 164.018-5 - Specifications and standards incorporated by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (August 12, 1970), entitled “Cloth, Drill, Cotton.” (4) Federal Specification CCC-C-443 E (December 2, 1974), entitled “Cloth, Duck, Cotton (Single and Plied Filling Yarns, Flat).” (5) Federal Test Method... MIL-C-17415 E (April 16, 1964), entitled “Cloth, Coated, and Webbing, Inflatable Boat and...

Genetic transformation of sweet orange with the coat protein gene of Citrus psorosis virus and evaluation of resistance against the virus.

PubMed

Zanek, María Cecilia; Reyes, Carina Andrea; Cervera, Magdalena; Peña, Eduardo José; Velázquez, Karelia; Costa, Norma; Plata, Maria Inés; Grau, Oscar; Peña, Leandro; García, María Laura

2008-01-01

Citrus psorosis is a serious viral disease affecting citrus trees in many countries. Its causal agent is Citrus psorosis virus (CPsV), the type member of genus Ophiovirus. CPsV infects most important citrus varieties, including oranges, mandarins and grapefruits, as well as hybrids and citrus relatives used as rootstocks. Certification programs have not been sufficient to control the disease and no sources of natural resistance have been found. Pathogen-derived resistance (PDR) can provide an efficient alternative to control viral diseases in their hosts. For this purpose, we have produced 21 independent lines of sweet orange expressing the coat protein gene of CPsV and five of them were challenged with the homologous CPV 4 isolate. Two different viral loads were evaluated to challenge the transgenic plants, but so far, no resistance or tolerance has been found in any line after 1 year of observations. In contrast, after inoculation all lines showed characteristic symptoms of psorosis in the greenhouse. The transgenic lines expressed low and variable amounts of the cp gene and no correlation was found between copy number and transgene expression. One line contained three copies of the cp gene, expressed low amounts of the mRNA and no coat protein. The ORF was cytosine methylated suggesting a PTGS mechanism, although the transformant failed to protect against the viral load used. Possible causes for the failed protection against the CPsV are discussed.

40 CFR 63.5170 - How do I demonstrate compliance with the standards?

Code of Federal Regulations, 2014 CFR

2014-07-01

... percent on a monthly basis for individual or groups of coil coating lines; or overall organic HAP control... combination of compliant coatings and control devices and maintaining an acceptable equivalent emission rate... facility. (6) Control efficiency calculation of HAP emitted. For each work station or group of work...

40 CFR 63.5170 - How do I demonstrate compliance with the standards?

Code of Federal Regulations, 2012 CFR

2012-07-01

... percent on a monthly basis for individual or groups of coil coating lines; or overall organic HAP control... combination of compliant coatings and control devices and maintaining an acceptable equivalent emission rate... facility. (6) Control efficiency calculation of HAP emitted. For each work station or group of work...

40 CFR 63.5170 - How do I demonstrate compliance with the standards?

Code of Federal Regulations, 2013 CFR

2013-07-01

... percent on a monthly basis for individual or groups of coil coating lines; or overall organic HAP control... combination of compliant coatings and control devices and maintaining an acceptable equivalent emission rate... facility. (6) Control efficiency calculation of HAP emitted. For each work station or group of work...

High-resolution Thermal Micro-imaging Using Europium Chelate Luminescent Coatings

DOE PAGES

Benseman, Timothy M.; Hao, Yang; Vlasko-Vlasov, Vitalii K.; ...

2017-04-16

Europium thenoyltrifluoroacentonate (EuTFC) has an optical luminescence line at 612 nm, whose activation efficiency decreases strongly with temperature. If a sample coated with a thin film of this material is micro-imaged, the 612 nm luminescent response intensity may be converted into a direct map of sample surface temperature.

Online Coupling of Flow-Field Flow Fractionation and Single Particle Inductively Coupled Plasma-Mass Spectrometry: Characterization of Nanoparticle Surface Coating Thickness and Aggregation State

EPA Science Inventory

Surface coating thickness and aggregation state have strong influence on the environmental fate, transport, and toxicity of engineered nanomaterials. In this study, flow-field flow fractionation coupled on-line with single particle inductively coupled plasma-mass spectrometry i...

The Effectiveness of Surface Coatings on Preventing Interfacial Reaction During Ultrasonic Welding of Aluminum to Magnesium

NASA Astrophysics Data System (ADS)

Panteli, Alexandria; Robson, Joseph D.; Chen, Ying-Chun; Prangnell, Philip B.

2013-12-01

High power ultrasonic spot welding (USW) is a solid-state joining process that is advantageous for welding difficult dissimilar material couples, like magnesium to aluminum. USW is also a useful technique for testing methods of controlling interfacial reaction in welding as the interface is not greatly displaced by the process. However, the high strain rate deformation in USW has been found to accelerate intermetallic compound (IMC) formation and a thick Al12Mg17 and Al3Mg2 reaction layer forms after relatively short welding times. In this work, we have investigated the potential of two approaches for reducing the IMC reaction rate in dissimilar Al-Mg ultrasonic welds, both involving coatings on the Mg sheet surface to (i) separate the join line from the weld interface, using a 100- μm-thick Al cold spray coating, and (ii) provide a diffusion barrier layer, using a thin manganese physical vapor deposition (PVD) coating. Both methods were found to reduce the level of reaction and increase the failure energy of the welds, but their effectiveness was limited due to issues with coating attachment and survivability during the welding cycle. The effect of the coatings on the joint's interface microstructure, and the fracture behavior have been investigated in detail. Kinetic modeling has been used to show that the benefit of the cold spray coating can be attributed to the reaction rate reverting to that expected under static conditions. This reduces the IMC growth rate by over 50 pct because at the weld line, the high strain rate dynamic deformation in USW normally enhances diffusion through the IMC layer. In comparison, the thin PVD barrier coating was found to rapidly break up early in USW and become dispersed throughout the deformation layer reducing its effectiveness.

tRNAscan-SE On-line: integrating search and context for analysis of transfer RNA genes.

PubMed

Lowe, Todd M; Chan, Patricia P

2016-07-08

High-throughput genome sequencing continues to grow the need for rapid, accurate genome annotation and tRNA genes constitute the largest family of essential, ever-present non-coding RNA genes. Newly developed tRNAscan-SE 2.0 has advanced the state-of-the-art methodology in tRNA gene detection and functional prediction, captured by rich new content of the companion Genomic tRNA Database. Previously, web-server tRNA detection was isolated from knowledge of existing tRNAs and their annotation. In this update of the tRNAscan-SE On-line resource, we tie together improvements in tRNA classification with greatly enhanced biological context via dynamically generated links between web server search results, the most relevant genes in the GtRNAdb and interactive, rich genome context provided by UCSC genome browsers. The tRNAscan-SE On-line web server can be accessed at http://trna.ucsc.edu/tRNAscan-SE/. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Sub-10-nm suspended nano-web formation by direct laser writing

NASA Astrophysics Data System (ADS)

Wang, Sihao; Yu, Ye; Liu, Hailong; Lim, Kevin T. P.; Madurai Srinivasan, Bharathi; Zhang, Yong Wei; Yang, Joel K. W.

2018-06-01

A diffraction-limited three-dimensional (3D) direct laser writing (DLW) system based on two-photon polymerization can routinely pattern structures at the 100 nm length scale. Several schemes have been developed to improve the patterning resolution of 3D DLW but often require customized resist formulations or multi-wavelength exposures. Here, we introduce a scheme to produce suspended nano-webs with feature sizes below 10 nm in IP-Dip resist using sub-threshold exposure conditions in a commercial DLW system. The narrowest suspended lines (nano-webs) measured 7 nm in width. Larger ∼20 nm nano-webs were patterned with ∼80% yield at increased laser powers. In addition, closely spaced nano-gaps with a center-to-center distance of 33 nm were produced by patterning vertically displaced suspended lines followed by metal deposition and liftoff. We provide hypotheses and present preliminary results for a mechanism involving the initiation of a percolative path and a strain-induced narrowing in the nano-web formation. Our approach allows selective features to be patterned with dimensions comparable to the sub-10 nm patterning capability of electron-beam lithography (EBL).

Energy absorption device for shock loading

NASA Astrophysics Data System (ADS)

Howard, C. D.; Lagrange, Donald E.; Beatty, David A.; Littman, David C.

1995-02-01

A shock energy absorbing device provides shock protection for the riser line employed to attach an aerodynamic deceleration device to a primary body during deployment of the system into an airstream. During deployment, for example, by dropping an unopened parachute and attached load or by rocket delivery of the unopened parachute and attached load, the parachute is made to open at a desired altitude whereupon very large shock tension forces are generated which are applied to the line. In order to protect the line from failing under these forces and to reduce the requirement for a bulky, heavy line, a shock absorber is provided in the form of a block having one or more breakable web portions formed therein and through which the riser line is threaded. Upon deployment of the system into an airstream, the shock tension forces operate to fracture some or all of the breakable web portions thereby dissipating the shock energy generated during deployment and protecting the riser line from failure.

40 CFR Table 2 of Subpart Aaaaaaa... - Emission Limits for Asphalt Roofing Manufacturing (Coating) Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Coater-only production lines a. Limit PAH emissions to 0.0002 lb/ton of asphalt roofing product...-only production lines a. Limit PAH emissions to 0.0007 lb/ton of asphalt roofing product manufactured... saturator/coater production lines a. Limit PAH emissions to 0.0009 lb/ton of asphalt roofing product...

The effects of simulated low Earth orbit environments on spacecraft thermal control coatings

NASA Technical Reports Server (NTRS)

Dever, Joyce A.; Rutledge, Sharon K.; Bruckner, Eric J.; Stidham, Curtis R.; Stueber, Thomas J.; Booth, Roy E.

1993-01-01

Candidate Space Station Freedom radiator coatings including Z-93, YB-71, anodized aluminum and SiO(x) coated silvered Teflon have been characterized for optical properties degradation upon exposure to environments containing atomic oxygen, vacuum ultraviolet (VUV) radiation, and/or silicone contamination. YB-71 coating showed a blue-gray discoloration, which has not been observed in space, upon exposure in atomic oxygen facilities which also provide exaggerated VUV radiation. This is evidence that damage mechanisms occur in these ground laboratory facilities which are different from those which occur in space. Radiator coatings exposed to an electron cyclotron resonance (ECR) atomic oxygen source in the presence of silicone-containing samples showed severe darkening from the intense VUV radiation provided by the ECR and from silicone contamination. Samples exposed to atomic oxygen from the ECR source and to VUV lamps, simultaneously, with in situ reflectance measurement, showed that significantly greater degradation occurred when samples received line-of-site ECR beam exposure than when samples were exposed to atomic oxygen scattered off of quartz surfaces without line-of-site view of the ECR beam. For white paints, exposure to air following atomic oxygen/VUV exposure reversed the darkening due to VUV damage. This illustrates the importance of in situ reflectance measurement.

Geometrical control of dissipation during the spreading of liquids on soft solids

NASA Astrophysics Data System (ADS)

Zhao, Menghua; Dervaux, Julien; Narita, Tetsuharu; Lequeux, François; Limat, Laurent; Roché, Matthieu

2018-02-01

Gel layers bound to a rigid substrate are used in cell culture to control differentiation and migration and to lower the friction and tailor the wetting of solids. Their thickness, often considered a negligible parameter, affects cell mechanosensing or the shape of sessile droplets. Here, we show that the adjustment of coating thickness provides control over energy dissipation during the spreading of flowing matter on a gel layer. We combine experiments and theory to provide an analytical description of both the statics and the dynamics of the contact line between the gel, the liquid, and the surrounding atmosphere. We extract from this analysis a hitherto-unknown scaling law that predicts the dynamic contact angle between the three phases as a function of the properties of the coating and the velocity of the contact line. Finally, we show that droplets moving on vertical substrates coated with gel layers having linear thickness gradients drift toward regions of higher energy dissipation. Thus, thickness control opens the opportunity to design a priori the path followed by large droplets moving on gel-coated substrates. Our study shows that thickness is another parameter, besides surface energy and substrate mechanics, to tune the dynamics of liquid spreading and wetting on a compliant coating, with potential applications in dew collection and free-surface flow control.

Removal of virus and toxin using heatable multi-walled carbon nanotube web filters

NASA Astrophysics Data System (ADS)

Jang, Hoon-Sik; Jeon, Sang Koo; Ryu, Kwon-Sang; Nahm, Seung Hoon

2016-02-01

Many studies have used a carbon nanotube (CNT) filter for pathogen removal and/or inactivation by means of electrochemical or electrochlorination. The large surface area, fine pore size and high electrical and thermal conductivity of CNTs make them suitable and distinct to use for the filtering and removal of pathogens. Here, we grew spin-capable multi-walled CNTs (MWCNTs) and manufactured a web filter using the spun MWCNTs. Botulinum toxin type E light chain (BoT/E-LC) and vaccinia virus (VV) were filtered using the MWCNT web filters and were evaporated and removed by applying direct current (DC) voltage to both sides of the MWCNT webs, excluding electrochemical or electrochlorination. The filtering and removal of BoT/E-LC and VV were performed after seven layers of the MWCNT sheets were coated onto a silicon oxide porous plate. The electrical resistance of the webs in the seven layer sheet was 293 Ω. The temperature of MWCNTs webs was linearly increased to ˜300 °C at 210 V of DC voltage. This temperature was enough to remove BoT/E-LC and VV. From the SEM and XPS results, we confirmed that BoT/E-LC and VV on the MWCNT webs were almost removed by applying a DC voltage and that some element (N, Na, Cl, etc.) as residues on the MWCNT webs remained.

[Virus resistance in transgenic watermelon plants containing a WMV-2 coat protein gene].

PubMed

Wang, Hui-Zhong; Zhao, Pei-Jie; Xu, Ji-Chen; Zhao, Huai; Zhang, Hong-Sheng

2003-01-01

Virus disease is a major cause that affects the quality and output of watermelon which is an important fruit in summer. So it is really urgent to develop disease resistance plants. But it takes a long time to breed such plants in conventional ways, and it is very difficult to get ideal result. With the development of plant genetic engineering, new ways have been found to breed plants with disease resistance. By using plant transgenic technique, much progress was been made in plant improvement. There are many successful cases of transgenic plants against corresponding virus disease through transferring coat protein gene. This paper reports the results of inheritance, segregation, expression of WMV-2 coat protein gene in inbred transgenic watermelon and its resistance to virus. Through PCR analysis of inbred plants, we found WMV-2 coat protein gene in the genome of progeny R1 separated with 3:1. After successive selection and identification of 4 generations, 8 transgenic pure lines with almost the same agronomic traits were obtained from 3 independent transformants of T7, T11 and T32. The result of Western blotting shows all 3 different transgenic lines of R4T7-1, R4T11-3 and R4T32-7 can produce coat protein. Disease resistance experiment on transgenic plants with WMV-2 shows that, compared with the control groups, transgenic plants can delay the disease infection and reduce the incidence and the symptoms of virus disease. And the transgenic line R4T32-7 expressed high resistance to infection by WMV-2, which lays a foundation for breeding of disease resistant varieties through plant transgenic technique.

Examination of a carton sealing line using a thermographic scanner

NASA Astrophysics Data System (ADS)

Kleinfeld, Jack M.

1999-03-01

The study of the operation and performance of natural gas fired sealing lines for polyethylene coated beverage containers was performed. Both thermal and geometric data was abstracted from the thermal scans and used to characterize the performance of the sealing line. The impact of process operating variables such as line speed and carton to carton spacing was studied. Recommendations for system improvements, instrumentation and process control were made.

Feasibility of Raman spectroscopy as PAT tool in active coating.

PubMed

Müller, Joshua; Knop, Klaus; Thies, Jochen; Uerpmann, Carsten; Kleinebudde, Peter

2010-02-01

Active coating is a specific application of film coating where the active ingredient is comprised in the coating layer. This implementation is a challenging operation regarding the achievement of desired amount of coating and coating uniformity. To guarantee the quality of such dosage forms it is desirable to develop a tool that is able to monitor the coating operation and detect the end of the process. Coating experiments were performed at which the model drug diprophylline is coated in a pan coater on placebo tablets and tablets containing the active ingredient itself. During the active coating Raman spectra were recorded in-line. The spectral measurements were correlated with the average weight gain and the amount of coated active ingredient at each time point. The developed chemometric model was tested by monitoring further coated batches. Furthermore, the effects of pan rotation speed and working distance on the acquired Raman signal and, hence, resulting effect of the chemometric model were examined. Besides coating on placebo cores it was possible to determine the amount of active ingredient in the film when coated onto cores containing the same active ingredient. In addition, the method is even applicable when varying the process parameters and measurement conditions within a restricted range. Raman spectroscopy is an appropriate process analytical technology too.

Microbial Penetration and Utilization of Organic Aircraft Fuel-Tank Coatings1

PubMed Central

Crum, M. G.; Reynolds, R. J.; Hedrick, H. G.

1967-01-01

Microorganisms have been found as contaminants in various types of aircraft fuel tanks. Their presence introduces problems in the operation of the aircraft, including destruction of components such as the organic coatings used as protective linings in the fuel tanks. Microbial penetration and utilization of the currently used organic coatings, EC 776, DV 1180, PR 1560, and DeSoto 1080, were determined by changes in electrical resistances of the coatings; mycelial weight changes; growth counts of the bacteria; and manometric determinations on Pseudomonas aeruginosa (GD-FW B-25) and Cladosporium resinae (QMC-7998). The results indicate EC 776 and DV 1180 to be less resistant to microbial degradation than the other coatings. Organic coatings, serving as a source of nutrition, would be conducive to population buildups in aircraft fuel tanks. Images Fig. 1 PMID:16349744

Community-LINE Source Model (C-LINE) to estimate roadway emissions

EPA Pesticide Factsheets

C-LINE is a web-based model that estimates emissions and dispersion of toxic air pollutants for roadways in the U.S. This reduced-form air quality model examines what-if scenarios for changes in emissions such as traffic volume fleet mix and vehicle speed.

Maximizing the quantum efficiency of microchannel plate detectors - The collection of photoelectrons from the interchannel web using an electric field

NASA Technical Reports Server (NTRS)

Taylor, R. C.; Hettrick, M. C.; Malina, R. F.

1983-01-01

High quantum efficiency and two-dimensional imaging capabilities make the microchannel plate (MCP) a suitable detector for a sky survey instrument. The Extreme Ultraviolet Explorer satellite, to be launched in 1987, will use MCP detectors. A feature which limits MCP efficiency is related to the walls of individual channels. The walls are of finite thickness and thus form an interchannel web. Under normal circumstances, this web does not contribute to the detector's quantum efficiency. Panitz and Foesch (1976) have found that in the case of a bombardment with ions, electrons were ejected from the electrode material coating the web. By applying a small electric field, the electrons were returned to the MCP surface where they were detected. The present investigation is concerned with the enhancement of quantum efficiencies in the case of extreme UV wavelengths. Attention is given to a model and a computer simulation which quantitatively reproduce the experimental results.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higgins, G.L.; Bates, C.R.

A new procedure for testing elevated-temperature cathodic disbondment (C.D.) in fusion-bonded epoxy (FBE) pipeline coatings appears consistent and reliable. Further, its results question C.D. theories that fail to account for effects at above-ambient temperatures. The work to develop this procedure also included experiments that demonstrated how the relative performance of coating systems - especially FBE line-pipe coatings operated at elevated temperature - could not be predicted from ambient-temperature assessment. Data reported in this third in a series on pipeline-protection technology confirm and expand on these aspects and introduce more recent results on the behavior of FBE coatings subjected to elevated-temperaturemore » C.D. testing.« less

75 FR 64314 - Oncologic Drugs Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

... check the Agency's Web site and call the appropriate advisory committee hot line/phone line to learn... the proposed trade name Zictifa (vandetanib) Tablets, manufactured by iPR Pharmaceuticals, Inc...

76 FR 46304 - Pediatric Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-02

... Agency's Web site and call the appropriate advisory committee hot line/phone line to learn about possible... (zolmitriptan). There will be an informational update on Kaletra (lopinavir/ritonavir) oral solution and tablets...

Development of high-efficiency solar cells on silicon web

NASA Technical Reports Server (NTRS)

Meier, D. L.

1986-01-01

Achievement of higher efficiency cells by directing efforts toward identifying carrier loss mechanisms; design of cell structures; and development of processing techniques are described. Use of techniques such as deep-level transient spectroscopy (DLTS), laser-beam-induced current (LBIC), and transmission electron microscopy (TEM) indicated that dislocations in web material rather than twin planes were primarily responsible for limiting diffusion lengths in the web. Lifetimes and cell efficiencies can be improved from 19 to 120 microns, and 8 to 10.3% (no AR), respectively, by implanting hydrogen at 1500 eV and a beam current density of 2.0 mA/sq cm. Some of the processing improvements included use of a double-layer AR coating (ZnS and MgF2) and an addition of an aluminum back surface reflectors. Cells of more than 16% efficiency were achieved.

Are we effectively informing patients? A quantitative analysis of on-line patient education resources from the American Society of Neuroradiology.

PubMed

Hansberry, D R; Agarwal, N; Gonzales, S F; Baker, S R

2014-07-01

The ubiquitous use of the Internet by the public in an attempt to better understand their health care requires the on-line resources written at an appropriate level to maximize comprehension for the average user. The National Institutes of Health and the American Medical Association recommend on-line patient education resources written at a third-to-seventh grade level. We evaluated the readability of the patient education resources provided on the Web site of the American Society of Neuroradiology (http://www.asnr.org/patientinfo/). All patient education material from the ASNR Web site and the Society of Neurointerventional Surgery Web site were downloaded and evaluated with the computer software, Readability Studio Professional Edition, by using 10 quantitative readability scales: the Flesch Reading Ease, Flesch-Kincaid Grade Level, Simple Measure of Gobbledygook, Coleman-Liau Index, Gunning Fog Index, New Dale-Chall, FORCAST Formula, Fry Graph, Raygor Reading Estimate, and New Fog Count. An unpaired t test was used to compare the readability level of resources available on the American Society of Neuroradiology and the Society of Neurointerventional Surgery Web sites. The 20 individual patient education articles were written at a 13.9 ± 1.4 grade level with only 5% written at <11th grade level. There was no statistical difference between the level of readability of the resources on the American Society of Neuroradiology and Society of Neurointerventional Surgery Web sites. The patient education resources on these Web sites fail to meet the guidelines of the National Institutes of Health and American Medical Association. Members of the public may fail to fully understand these resources and would benefit from revisions that result in more comprehensible information cast in simpler language. © 2014 by American Journal of Neuroradiology.

A biological method for in-situ synthesis of hydroxyapatite-coated magnetite nanoparticles using Enterobacter aerogenes: Characterization and acute toxicity assessments.

PubMed

Ahmadzadeh, Elham; Talebnia Rowshan, Farid; Hosseini, Morteza

2017-04-01

Hydroxyapatite (HA)-coated magnetite nanoparticles (MNPs) are being widely investigated for various applications in medical engineering and wastewater treatment. In this work, the MNPs were thoroughly coated by bacterial synthesized HA nanoparticles during biomineralization process using Enterobacter aerogenes. The resulting bacterial-induced precipitate was then calcined at 600°C and investigated with respect to structural characteristics, particle size and magnetic strength by XRD, FT-IR, SEM, EDS, TEM and VSM analyses. The effects of MNPs and HA-coated MNPs (HA-MNPs) on the viability of human MCF-7 cell lines were also investigated via mitochondrial activity test (MTT) and lactate dehydrogenase (LDH) assays. The powder characterization results showed appropriate structural properties for HA-MNPs samples. The particles diameter size of the MNPs and HA-MNPs were in the range of 3-25nm and 20-80nm, respectively. The biologically-synthesized HA-MNPs formed a stable suspension in water while keeping their magnetic property. The saturation magnetization (Ms) of HA-MNPs was measured at ~10emug -1 which was in good agreement with the structural composition of this sample. Finally, the results of the cell lines viability indicated that coating of toxic MNPs via biomineralization was a promising approach in order to synthesize bio-compatible magnetic nanoparticles with suitable physical and chemical structural characteristics. The toxicity level of MNPs was reduced by 10 fold when coated by bacterial-synthesized HA. Copyright © 2016 Elsevier B.V. All rights reserved.

76 FR 80929 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-27

... Activities; Submission to OMB for Review and Approval; Comment Request; NSPS for Metal Coil Surface Coating... information about the electronic docket, go to http://www.regulations.gov . Title: NSPS for Metal Coil Surface... promulgated on November 1, 1982. These regulations apply to the following surface coating lines in the metal...

Monitoring Coating Thickness During Plasma Spraying

NASA Technical Reports Server (NTRS)

Miller, Robert A.

1990-01-01

High-resolution video measures thickness accurately without interfering with process. Camera views cylindrical part through filter during plasma spraying. Lamp blacklights part, creating high-contrast silhouette on video monitor. Width analyzer counts number of lines in image of part after each pass of spray gun. Layer-by-layer measurements ensure adequate coat built up without danger of exceeding required thickness.

A General Purpose Connections type CTI Server Based on SIP Protocol and Its Implementation

NASA Astrophysics Data System (ADS)

Watanabe, Toru; Koizumi, Hisao

In this paper, we propose a general purpose connections type CTI (Computer Telephony Integration) server that provides various CTI services such as voice logging where the CTI server communicates with IP-PBX using the SIP (Session Initiation Protocol), and accumulates voice packets of external line telephone call flowing between an IP telephone for extension and a VoIP gateway connected to outside line networks. The CTI server realizes CTI services such as voice logging, telephone conference, or IVR (interactive voice response) with accumulating and processing voice packets sampled. Furthermore, the CTI server incorporates a web server function which can provide various CTI services such as a Web telephone directory via a Web browser to PCs, cellular telephones or smart-phones in mobile environments.

Simulation Comparisons of Three Different Meander Line Dipoles

DTIC Science & Technology

2015-01-01

Paez C I. Design formulas for a meandered dipole. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014. 2. Nguyen, VH, Phan, HP, Hoang...MH. Improving radiation characteristics of UHF RFID antennas by zigzag structures. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014...geometry-based, frequency-independent lumped element model. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014. 5. Olaode OO, Palmer WD

Supplementing Introductory Biology with On-Line Curriculum

ERIC Educational Resources Information Center

McGroarty, Estelle; Parker, Joyce; Heidemann, Merle; Lim, Heejun; Olson, Mark; Long, Tammy; Merrill, John; Riffell, Samuel; Smith, James; Batzli, Janet; Kirschtel, David

2004-01-01

We developed web-based modules addressing fundamental concepts of introductory biology delivered through the LON-CAPA course management system. These modules were designed and used to supplement large, lecture-based introductory biology classes. Incorporating educational principles and the strength of web-based instructional technology, choices…

Quantitative fabrication, performance optimization and comparison of PEG and zwitterionic polymer antifouling coatings.

PubMed

Xing, Cheng-Mei; Meng, Fan-Ning; Quan, Miao; Ding, Kai; Dang, Yuan; Gong, Yong-Kuan

2017-09-01

A versatile fabrication and performance optimization strategy of PEG and zwitterionic polymer coatings is developed on the sensor chip of surface plasma resonance (SPR) instrument. A random copolymer bearing phosphorylcholine zwitterion and active ester side chains (PMEN) and carboxylic PEG coatings with comparable thicknesses were deposited on SPR sensor chips via amidation coupling on the precoated polydopamine (PDA) intermediate layer. The PMEN coating showed much stronger resistance to bovine serum albumin (BSA) adsorption than PEG coating at very thin thickness (∼1nm). However, the BSA resistant efficacy of PEG coating could exceed that of PMEN due to stronger steric repelling effect when the thickness increased to 1.5∼3.3nm. Interestingly, both the PEG and PMEN thick coatings (≈3.6nm) showed ultralow fouling by BSA and bovine plasma fibrinogen (Fg). Moreover, changes in the PEG end group from -OH to -COOH, protein adsorption amount could increase by 10-fold. Importantly, the optimized PMEN and PEG-OH coatings were easily duplicated on other substrates due to universal adhesion of the PDA layer, showed excellent resistance to platelet, bacteria and proteins, and no significant difference in the antifouling performances was observed. These detailed results can explain the reported discrepancy in performances between PEG and zwitterionic polymer coatings by thickness. This facile and substrate-independent coating strategy may benefit the design and manufacture of advanced antifouling biomedical devices and long circulating nanocarriers. Prevention of biofouling is one of the biggest challenges for all biomedical applications. However, it is very difficult to fabricate a highly hydrophilic antifouling coating on inert materials or large devices. In this study, PEG and zwitterion polymers, the most widely investigated polymers with best antifouling performance, are conveniently immobilized on different kinds of substrates from their aqueous solutions by precoating a polydopamine intermediate layer as the universal adhesive and readily re-modifiable surface. Importantly, the coating fabrication and antifouling performance can be monitored and optimized quantitatively by a surface plasma resonance (SPR) system. More significantly, the SPR on-line optimized coatings were successfully duplicated off-line on other substrates, and supported by their excellent antifouling properties. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Publishing biomedical journals on the World-Wide Web using an open architecture model.

PubMed Central

Shareck, E. P.; Greenes, R. A.

1996-01-01

BACKGROUND: In many respects, biomedical publications are ideally suited for distribution via the World-Wide Web, but economic concerns have prevented the rapid adoption of an on-line publishing model. PURPOSE: We report on our experiences with assisting biomedical journals in developing an online presence, issues that were encountered, and methods used to address these issues. Our approach is based on an open architecture that fosters adaptation and interconnection of biomedical resources. METHODS: We have worked with the New England Journal of Medicine (NEJM), as well as five other publishers. A set of tools and protocols was employed to develop a scalable and customizable solution for publishing journals on-line. RESULTS: In March, 1996, the New England Journal of Medicine published its first World-Wide Web issue. Explorations with other publishers have helped to generalize the model. CONCLUSIONS: Economic and technical issues play a major role in developing World-Wide Web publishing solutions. PMID:8947685

40 CFR 63.4322 - How do I demonstrate continuous compliance with the emission limitations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... which the mass fraction of organic HAP, determined according to the requirements of § 63.4321(e)(1)(iv... report required by § 63.4311, you must identify any web coating/printing operation, slashing operation, or dyeing/finishing operation for which you used the compliant material option. If there were no...

Multipurpose Prepregging Machine

NASA Technical Reports Server (NTRS)

Johnston, N. J.; Wilkinson, Steven; Marchello, J. M.; Dixon, D.

1995-01-01

Machine designed and built for variety of uses involving coating or impregnating ("prepregging") fibers, tows, yarns, or webs or tapes made of such fibrous materials with thermoplastic or thermosetting resins. Prepreg materials produced used to make matrix/fiber composite materials. Comprises modules operated individually, sequentially, or simultaneously, depending on nature of specific prepreg material and prepregging technique used. Machine incorporates number of safety features.

77 FR 8575 - National Emissions Standards for Hazardous Air Pollutants: Secondary Aluminum Production

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-14

... heating in a scrap dryer, delacquering kiln or decoating kiln to remove coatings or other contaminants... instructions for submitting comments. Email: a-and-r[email protected] , Attention Docket ID Number EPA-HQ-OAR...://www.regulations.gov Web site is an ``anonymous access'' system, which means the EPA will not know your...

40 CFR 63.4310 - What notifications must I submit?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., using Equation 1 of § 63.4321. (ii) For the emission rate without add-on controls option as specified in...) For the emission rate without add-on controls option as specified in § 63.4291(c)(2) for dyeing...-on controls option as specified in § 63.4291(a)(3) for web coating/printing operations, provide the...

40 CFR 63.4341 - How do I demonstrate initial compliance?

Code of Federal Regulations, 2011 CFR

2011-07-01

... accurate to within ±2.0 percent of the mass of volatile organic matter recovered. (ii) For each solvent... Equation 2 of § 63.4331. q = Number of controlled web coating/printing operations not using a liquid-liquid... compliance period. The device must be initially certified by the manufacturer to be accurate to within ±2.0...

40 CFR 63.4341 - How do I demonstrate initial compliance?

Code of Federal Regulations, 2010 CFR

2010-07-01

... accurate to within ±2.0 percent of the mass of volatile organic matter recovered. (ii) For each solvent... Equation 2 of § 63.4331. q = Number of controlled web coating/printing operations not using a liquid-liquid... compliance period. The device must be initially certified by the manufacturer to be accurate to within ±2.0...

Spider orb webs rely on radial threads to absorb prey kinetic energy

PubMed Central

Sensenig, Andrew T.; Lorentz, Kimberly A.; Kelly, Sean P.; Blackledge, Todd A.

2012-01-01

The kinetic energy of flying insect prey is a formidable challenge for orb-weaving spiders. These spiders construct two-dimensional, round webs from a combination of stiff, strong radial silk and highly elastic, glue-coated capture spirals. Orb webs must first stop the flight of insect prey and then retain those insects long enough to be subdued by the spiders. Consequently, spider silks rank among the toughest known biomaterials. The large number of silk threads composing a web suggests that aerodynamic dissipation may also play an important role in stopping prey. Here, we quantify energy dissipation in orb webs spun by diverse species of spiders using data derived from high-speed videos of web deformation under prey impact. By integrating video data with material testing of silks, we compare the relative contributions of radial silk, the capture spiral and aerodynamic dissipation. Radial silk dominated energy absorption in all webs, with the potential to account for approximately 100 per cent of the work of stopping prey in larger webs. The most generous estimates for the roles of capture spirals and aerodynamic dissipation show that they rarely contribute more than 30 per cent and 10 per cent of the total work of stopping prey, respectively, and then only for smaller orb webs. The reliance of spider orb webs upon internal energy absorption by radial threads for prey capture suggests that the material properties of the capture spirals are largely unconstrained by the selective pressures of stopping prey and can instead evolve freely in response to alternative functional constraints such as adhering to prey. PMID:22431738

Spider orb webs rely on radial threads to absorb prey kinetic energy.

PubMed

Sensenig, Andrew T; Lorentz, Kimberly A; Kelly, Sean P; Blackledge, Todd A

2012-08-07

The kinetic energy of flying insect prey is a formidable challenge for orb-weaving spiders. These spiders construct two-dimensional, round webs from a combination of stiff, strong radial silk and highly elastic, glue-coated capture spirals. Orb webs must first stop the flight of insect prey and then retain those insects long enough to be subdued by the spiders. Consequently, spider silks rank among the toughest known biomaterials. The large number of silk threads composing a web suggests that aerodynamic dissipation may also play an important role in stopping prey. Here, we quantify energy dissipation in orb webs spun by diverse species of spiders using data derived from high-speed videos of web deformation under prey impact. By integrating video data with material testing of silks, we compare the relative contributions of radial silk, the capture spiral and aerodynamic dissipation. Radial silk dominated energy absorption in all webs, with the potential to account for approximately 100 per cent of the work of stopping prey in larger webs. The most generous estimates for the roles of capture spirals and aerodynamic dissipation show that they rarely contribute more than 30 per cent and 10 per cent of the total work of stopping prey, respectively, and then only for smaller orb webs. The reliance of spider orb webs upon internal energy absorption by radial threads for prey capture suggests that the material properties of the capture spirals are largely unconstrained by the selective pressures of stopping prey and can instead evolve freely in response to alternative functional constraints such as adhering to prey.

Roadway data representation and application development : final report, December 2009.

DOT National Transportation Integrated Search

2009-08-06

The Straight-line Diagrammer, a web-based application to produce Straight-line Diagrams (SLDs) automatically, was developed in this project to replace old application (AutoSLD) which has outdated structure and limited capabilities.

Diagrammatic exponentiation for products of Wilson lines

NASA Astrophysics Data System (ADS)

Mitov, Alexander; Sterman, George; Sung, Ilmo

2010-11-01

We provide a recursive diagrammatic prescription for the exponentiation of gauge theory amplitudes involving products of Wilson lines and loops. This construction generalizes the concept of webs, originally developed for eikonal form factors and cross sections with two eikonal lines, to general soft functions in QCD and related gauge theories. Our coordinate space arguments apply to arbitrary paths for the lines.

A Web-Based Synchronous Collaborative Review Tool: A Case Study of an On-Line Graduate Course

ERIC Educational Resources Information Center

Serce, Fatma Cemile; Yildirim, Soner

2006-01-01

On-line collaboration is an instructional method that facilitates collaboration in an on-line learning setting. To promote effective collaboration, it is vital to reveal both the student's and the instructor's point of view pertaining to effective on-line collaboration. In this study, the effectiveness of a learning management system in on-line…

Versatile Coating

NASA Technical Reports Server (NTRS)

1990-01-01

A radome at Logan Airport and a large parabolic antenna at the Wang Building in Massachusetts are protected from weather, corrosion and ultraviolet radiation by a coating, specially designed for antennas and radomes, known as CRC Weathertite 6000. The CRC 6000 line that emerged from Boyd Coatings Research Co., Inc. is a solid dispersion of fluorocarbon polymer and polyurethane that yields a tough, durable film with superior ultraviolet resistance and the ability to repel water and ice over a long term. Additionally, it provides resistance to corrosion, abrasion, chemical attacks and impacts. Material can be used on a variety of substrates, such as fiberglass, wood, plastic and concrete in addition to steel and aluminum. In addition Boyd Coatings sees CRC 6000 applicability as an anti-icing system coated on the leading edge of aircraft wings.

A Web Tool for Research in Nonlinear Optics

NASA Astrophysics Data System (ADS)

Prikhod'ko, Nikolay V.; Abramovsky, Viktor A.; Abramovskaya, Natalia V.; Demichev, Andrey P.; Kryukov, Alexandr P.; Polyakov, Stanislav P.

2016-02-01

This paper presents a project of developing the web platform called WebNLO for computer modeling of nonlinear optics phenomena. We discuss a general scheme of the platform and a model for interaction between the platform modules. The platform is built as a set of interacting RESTful web services (SaaS approach). Users can interact with the platform through a web browser or command line interface. Such a resource has no analogues in the field of nonlinear optics and will be created for the first time therefore allowing researchers to access high-performance computing resources that will significantly reduce the cost of the research and development process.

Effect of particle in-flight behavior on the composition of thermal barrier coatings

NASA Astrophysics Data System (ADS)

Zhao, L.; Bai, Y.; Tang, J. J.; Liu, K.; Ding, C. H.; Yang, J. F.; Han, Z. H.

2013-12-01

In this work, 6 to 11 mol% YO1.5-stabilized zirconia (YSZ) coatings were deposited by supersonic and conventional atmospheric plasma spraying. During spraying, the surface temperature and velocity of in-flight particles were monitored by Spray Watch 2i on-line system. The phase composition of as-sprayed coatings was analyzed by X-ray diffractometry (XRD). Lattice parameters, tetragonality and the content of YO1.5 (mol%) of as-sprayed coatings were calculated according to the position of (0 0 4) and (4 0 0) diffraction peaks. It was found that the as-sprayed coatings were composed of metastable non-transformable tetragonal phase (t‧). However, the amount of YO1.5 (mol%) in the as-sprayed coatings decreased with the increase of melting index of in-flight particles due to the partial evaporation of YO1.5 during spraying.

Aerocoat 7 Replacement Coatings

NASA Technical Reports Server (NTRS)

2008-01-01

Kennedy Space Center has used Aerocoat 7 (AR-7) to protect stainless-steel flex hoses at Launch Complex (LC-39) and hydraulic lines of the Mobile Launcher Platform (MLP) because it provides excellent corrosion protection in low-temperature applications. The Sovereign Company produced AR-7 exclusively for NASA but discontinued production because the coating released high levels of volatile organic compounds (VOCs) and had a significant environmental impact. The purpose of this project was to select and evaluate potential replacement coatings for AR-7 that would be more environmentally sound. The physical and mechanical properties of commercially available coatings were investigated through the Internet. The ideal coating would be fluid enough to penetrate the outer mesh of a stainless-steel flex hose and coat the inner hose, and flexible enough to withstand the movement of the hose, as well as the expansion and contraction of its metal caused by changes in temperature.

Development of improved high temperature coatings for IN-792 + HF

NASA Technical Reports Server (NTRS)

Profant, D. D.; Naik, S. K.

1981-01-01

The development for t-55 l712 engine of high temperature for integral turbine nozzles with improved thermal fatigue resistance without sacrificing oxidation/corrosion protection is discussed. The program evaluated to coating systems which comprised one baseline plasma spray coating (12% Al-NiCoCrALY), three aluminide coatings including the baseline aluminide (701), two CoNiCrAly (6% Al) + aluminide systems and four NiCoCrY + aluminide coating were evaluated. The two-step coating processes were investigated since it offered the advantage of tailoring the composition as well as properly coating surfaces of an integral or segmented nozzle. Cyclic burner rig thermal fatigue and oxidation/corrosion tests were used to evaluate the candidate coating systems. The plasma sprayed 12% Al-NiCoCrAlY was rated the best coating in thermal fatigue resistance and outperformed all coatings by a factor between 1.4 to 2.5 in cycles to crack initiation. However, this coatings is not applicable to integral or segmented nozzles due to the line of sight limitation of the plasma spray process. The 6% Al-CoNiCrAlY + Mod. 701 aluminide (32 w/o Al) was rated the best coating in oxidation/corrosion resistance and was rated the second best in thermal fatigue resistance.

Performance Prediction for Coatings. Proceedings of a Workshop at the Naval Civil Engineering Laboratory, 15 September 1986

DTIC Science & Technology

1987-10-01

Facilities" (A-65) Summary: Samples of the coating systems prepared for NCEL performance prediction studies were tested by alternate immersion in salt...coating sample where the yeast growth is inhibited over a 72-hour period. 5 - .. -, a . - - tL .naa t ~ ~S ~* r* J.r~ ¶Sf ~ ~t~ 9n~ PbP. bPjht fLMM...which is employed as a means of measuring the decibels of attenuation of the echoes caused by the sample on the line. The exponential decay of the

Thermoplastic coating of carbon fibers

NASA Technical Reports Server (NTRS)

Edie, D. D.; Lickfield, G. C.; Drews, M. J.; Ellison, M. S.; Allen, L. E.; Mccollum, J. R.; Thomas, H. L.

1988-01-01

Now that quantities of prepreg were made on the thermoplastic coating line, they are being formed into both textile preform structures and directly into composite samples. The textile preforms include both woven and knitted structures which will be thermoformed into a finished part. In order to determine if the matrix resin is properly adhering to the fibers or if voids are being formed in the coating process, the tensile strength and modulus of these samples will be tested. The matrix uniformity of matrix distribution in these samples is also being determined using an image analyzer.

Use of World Wide Web server and browser software to support a first-year medical physiology course.

PubMed

Davis, M J; Wythe, J; Rozum, J S; Gore, R W

1997-06-01

We describe the use of a World Wide Web (Web) server to support a team-taught physiology course for first-year medical students. Our objectives were to reduce the number of formal lecture hours and enhance student enthusiasm by using more multimedia materials and creating opportunities for interactive learning. On-line course materials, consisting of administrative documents, lecture notes, animations, digital movies, practice tests, and grade reports, were placed on a departmental computer with an Internet connection. Students used Web browsers to access on-line materials from a variety of computing platforms on campus, at home, and at remote sites. To assess use of the materials and their effectiveness, we analyzed 1) log files from the server, and 2) the results of a written course evaluation completed by all students. Lecture notes and practice tests were the most-used documents. The students' evaluations indicated that computer use in class made the lecture material more interesting, while the on-line documents helped reinforce lecture materials and the textbook. We conclude that the effectiveness of on-line materials depends on several different factors, including 1) the number of instructors that provide materials; 2) the quantity of other materials handed out; 3) the degree to which computer use is demonstrated in class and integrated into lectures; and 4) the ease with which students can access the materials. Finally, we propose that additional implementation of Internet-based resources beyond what we have described would further enhance a physiology course for first-year medical students.

The ChIP-Seq tools and web server: a resource for analyzing ChIP-seq and other types of genomic data.

PubMed

Ambrosini, Giovanna; Dreos, René; Kumar, Sunil; Bucher, Philipp

2016-11-18

ChIP-seq and related high-throughput chromatin profilig assays generate ever increasing volumes of highly valuable biological data. To make sense out of it, biologists need versatile, efficient and user-friendly tools for access, visualization and itegrative analysis of such data. Here we present the ChIP-Seq command line tools and web server, implementing basic algorithms for ChIP-seq data analysis starting with a read alignment file. The tools are optimized for memory-efficiency and speed thus allowing for processing of large data volumes on inexpensive hardware. The web interface provides access to a large database of public data. The ChIP-Seq tools have a modular and interoperable design in that the output from one application can serve as input to another one. Complex and innovative tasks can thus be achieved by running several tools in a cascade. The various ChIP-Seq command line tools and web services either complement or compare favorably to related bioinformatics resources in terms of computational efficiency, ease of access to public data and interoperability with other web-based tools. The ChIP-Seq server is accessible at http://ccg.vital-it.ch/chipseq/ .

Designing a web site for high school geoscience teaching in Iceland

NASA Astrophysics Data System (ADS)

Douglas, George R.

1998-08-01

The need to construct an earth science teaching site on the web prompted a survey of existing sites which, in spite of containing much of value, revealed many weaknesses in basic design, particularly as regards the organisation of links to information resources. Few web sites take into consideration the particular pedagogic needs of the high school science student and there has, as yet, been little serious attempt to exploit and organise the more outstanding advantages offered by the internet to science teaching, such as accessing real-time data. A web site has been constructed which, through basic design, enables students to access relevant information resources over a wide range of subjects and topics easily and rapidly, while at the same time performing an instructional role in how to handle both on-line and off-line resources. Key elements in the design are selection and monitoring by the teacher, task oriented pages and the use of the Dewey decimal classification system. The intention is to increase gradually the extent to which most teaching tasks are carried out via the web pages, in the belief that they can become an efficient central point for all the earth science curriculum.

Development of an air knife to remove seed coat fragments during lint cleaning

USDA-ARS?s Scientific Manuscript database

An air knife is a tool commonly used to blow off debris in a manufacturing line. The knife may also be used to break the attachment force between a lint cleaner saw and a seed coat fragment (SCF) with attached fiber, and remove them. Work continued on evaluating an auxiliary air knife mounted on t...

Extreme ultraviolet performance of a multilayer coated high density toroidal grating

NASA Technical Reports Server (NTRS)

Thomas, Roger J.; Keski-Kuha, Ritva A. M.; Neupert, Werner M.; Condor, Charles E.; Gum, Jeffrey S.

1991-01-01

The performance of a multilayer coated diffraction grating has been evaluated at EUV wavelengths both in terms of absolute efficiency and spectral resolution. The application of ten-layer Ir/Si multilayer coating to a 3600-lines/mm blazed toroidal replica grating produced a factor of 9 enhancement in peak efficiency near the design wavelength of about 30 nm in first order, without degrading its excellent quasistigmatic spectral resolution. The measured EUV efficiency peaked at 3.3 percent and was improved over the full spectral range between 25 and 35 nm compared with the premultilayer replica which had a standard gold coating. In addition, the grating's spectral resolution of greater than 5000 was maintained.

Metal-coated Bragg grating reflecting fibre

NASA Astrophysics Data System (ADS)

Chamorovskiy, Yu. K.; Butov, O. V.; Kolosovskiy, A. O.; Popov, S. M.; Voloshin, V. V.; Vorob'ev, I. L.; Vyatkin, M. Yu.

2017-03-01

High-temperature optical fibres (OF) with fibre Bragg gratings (FBG) arrays written over a long length and in-line metal coating have been made for the first time. The optical parameters of the FBG arrays were tested by the optical frequency domain reflectometer (OFDR) method in a wide temperature range, demonstrating no degradation in reflection at heating up to 600 °C for a fibre with Al coating. The mechanical strength of the developed fibre was practically the same as "ordinary" OF with similar coating, showing the absence of the influence of FBG writing process on fibre strength. Further experiments are necessary to evaluate the possibility of further increases in the operational temperature range.

Bootstrapping and Maintaining Trust in the Cloud

DTIC Science & Technology

2016-03-16

of infrastructure-as-a- service (IaaS) cloud computing services such as Ama- zon Web Services, Google Compute Engine, Rackspace, et. al. means that...Implementation We implemented keylime in ∼3.2k lines of Python in four components: registrar, node, CV, and tenant. The registrar offers a REST-based web ...bootstrap key K. It provides an unencrypted REST-based web service for these two functions. As described earlier, the pro- tocols for exchanging data

Analysis of plastic deformation in silicon web crystals

NASA Technical Reports Server (NTRS)

Spitznagel, J. A.; Seidensticker, R. G.; Lien, S. Y.; Mchugh, J. P.; Hopkins, R. H.

1987-01-01

Numerical calculation of 111-plane 110-line slip activity in silicon web crystals generated by thermal stresses is in good agreement with etch pit patterns and X-ray topographic data. The data suggest that stress redistribution effects are small and that a model, similar to that proposed by Penning (1958) and Jordan (1981) but modified to account for dislocation annihilation and egress, can be used to describe plastic flow effects during silicon web growth.

X-ray Photoelectron Spectroscopy Database (Version 4.1)

National Institute of Standards and Technology Data Gateway

SRD 20 X-ray Photoelectron Spectroscopy Database (Version 4.1) (Web, free access)   The NIST XPS Database gives access to energies of many photoelectron and Auger-electron spectral lines. The database contains over 22,000 line positions, chemical shifts, doublet splittings, and energy separations of photoelectron and Auger-electron lines.

Study on the wiping gas jet in continuous galvanizing line

NASA Astrophysics Data System (ADS)

Kweon, Yong-Hun; Kim, Heuy-Dong

2011-09-01

In the continuous hot-dip galvanizing process, the gas-jet wiping is used to control the coating thickness of moving steel strip. The high speed gas-jet discharged from the nozzle slot impinges on the strip, and at this moment, wipes the liquid coating layer dragged by a moving strip. The coating thickness is generally influenced on the flow characteristics of wiping gas-jet such as the impinging pressure distribution, pressure gradient and shear stress distribution on the surface of strip. The flow characteristics of wiping gas-jet mentioned above depends upon considerably both the process operating conditions such as the nozzle pressure, nozzle-to-strip distance and line speed, and the geometry of gas-jet wiping apparatus such as the height of nozzle slot. In the present study, the effect of the geometry of nozzle on the coating thickness is investigated with the help of a computational fluid dynamics method. The height of nozzle slot is varied in the range of 0.6mm to 1.7mm. A finite volume method (FVM) is employed to solve two-dimensional, steady, compressible Navier-Stokes equations. Based upon the results obtained, the effect of the height of nozzle slot in the gas-jet wiping process is discussed in detail. The computational results show that for a given standoff distance between the nozzle to the strip, the effective height of nozzle slot exists in achieving thinner coating thickness.

The Impact of Supplementary On-Line Resources on Academic Performance: A Study of First-Year University Students Studying Economics

ERIC Educational Resources Information Center

Birch, Elisa; Williams, Andrew

2013-01-01

This paper examines the impact of supplementary web-based materials on students' academic performance in a first-year economics unit at university. In particular, the paper considers the impact of students' usage of the unit's webpage, voluntary on-line discussion board, voluntary on-line quizzes and voluntary on-line homework questions on their…

42 CFR 423.128 - Dissemination of Part D plan information.

Code of Federal Regulations, 2013 CFR

2013-10-01

... coverage determination and redetermination processes via an Internet Web site; and (iii) A system that... determination by contacting the plan sponsor's toll free customer service line or by accessing the plan sponsor's internet Web site. (8) Quality assurance policies and procedures. A description of the quality...

42 CFR 423.128 - Dissemination of Part D plan information.

Code of Federal Regulations, 2012 CFR

2012-10-01

... coverage determination and redetermination processes via an Internet Web site; and (iii) A system that... determination by contacting the plan sponsor's toll free customer service line or by accessing the plan sponsor's internet Web site. (8) Quality assurance policies and procedures. A description of the quality...

42 CFR 423.128 - Dissemination of Part D plan information.

Code of Federal Regulations, 2014 CFR

2014-10-01

... coverage determination and redetermination processes via an Internet Web site; and (iii) A system that... determination by contacting the plan sponsor's toll free customer service line or by accessing the plan sponsor's internet Web site. (8) Quality assurance policies and procedures. A description of the quality...

76 FR 77559 - Meeting of Humanities Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-13

... THE NATIONAL FOUNDATION ON THE ARTS AND THE HUMANITIES Meeting of Humanities Panel AGENCY: The... world history for the EDSITEment Web site. EDSITEment is an on-line educational partnership between the... creation of content for world history on the Endowment's EDSITEment Web site. Agenda: 9 a.m. to 12 p.m...

Sustainable Materials Management (SMM) Web Academy Webinar: Wasted Food to Energy: How 6 Water Resource Recovery Facilities are Boosting Biogas Production & the Bottom Line

EPA Pesticide Factsheets

This is a webinar page for the Sustainable Management of Materials (SMM) Web Academy webinar titled Let’s WRAP (Wrap Recycling Action Program): Best Practices to Boost Plastic Film Recycling in Your Community

Interactive Information Organization: Techniques and Evaluation

DTIC Science & Technology

2001-05-01

information search and access. Locating interesting information on the World Wide Web is the main task of on-line search engines . Such engines accept a...likelihood of being relevant to the user’s request. The majority of today’s Web search engines follow this scenario. The ordering of documents in the

Real-Time Collaboration of Virtual Laboratories through the Internet

ERIC Educational Resources Information Center

Jara, Carlos A.; Candelas, Francisco A.; Torres, Fernando; Dormido, Sebastian; Esquembre, Francisco; Reinoso, Oscar

2009-01-01

Web-based learning environments are becoming increasingly popular in higher education. One of the most important web-learning resources is the virtual laboratory (VL), which gives students an easy way for training and learning through the Internet. Moreover, on-line collaborative communication represents a practical method to transmit the…

Webquests in Social Studies Education

ERIC Educational Resources Information Center

Vanguri, Pradeep R.; Sunal, Cynthia Szymanski; Wilson, Elizabeth K.; Wright, Vivian H.

2004-01-01

WebQuests provide the opportunity to combine technology with educational concepts and to incorporate inquiry-based learning. WebQuests also have the ability to integrate on-line resources with student-centered, activity-based learning. Three courses in the College of Education at The University of Alabama and at West Virginia University…

22 CFR 42.33 - Diversity immigrants.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-line and submit to the Department of State via a Web site established by the Department of State for the purpose of receiving such petitions. The Department will specify the address of the Web site prior... neutral, light-colored background. Photos taken with very dark or patterned, busy backgrounds will not be...

22 CFR 42.33 - Diversity immigrants.

Code of Federal Regulations, 2012 CFR

2012-04-01

...-line and submit to the Department of State via a Web site established by the Department of State for the purpose of receiving such petitions. The Department will specify the address of the Web site prior... neutral, light-colored background. Photos taken with very dark or patterned, busy backgrounds will not be...

22 CFR 42.33 - Diversity immigrants.

Code of Federal Regulations, 2013 CFR

2013-04-01

...-line and submit to the Department of State via a Web site established by the Department of State for the purpose of receiving such petitions. The Department will specify the address of the Web site prior... neutral, light-colored background. Photos taken with very dark or patterned, busy backgrounds will not be...

22 CFR 42.33 - Diversity immigrants.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-line and submit to the Department of State via a Web site established by the Department of State for the purpose of receiving such petitions. The Department will specify the address of the Web site prior... neutral, light-colored background. Photos taken with very dark or patterned, busy backgrounds will not be...

22 CFR 42.33 - Diversity immigrants.

Code of Federal Regulations, 2014 CFR

2014-04-01

...-line and submit to the Department of State via a Web site established by the Department of State for the purpose of receiving such petitions. The Department will specify the address of the Web site prior... neutral, light-colored background. Photos taken with very dark or patterned, busy backgrounds will not be...

Biomedical Online Learning: The Route to Success

ERIC Educational Resources Information Center

Harvey, Patricia J.; Cookson, Barry; Meerabeau, Elizabeth; Muggleston, Diana

2003-01-01

The potential of the World Wide Web for rapid global communication is driving the creation of specifically tailored courses for employees, yet few practitioners have the necessary experience in on-line teaching methods, or in preparing documents for the web. Experience gained in developing six online training modules for the biotechnology and…

CliniWeb: managing clinical information on the World Wide Web.

PubMed

Hersh, W R; Brown, K E; Donohoe, L C; Campbell, E M; Horacek, A E

1996-01-01

The World Wide Web is a powerful new way to deliver on-line clinical information, but several problems limit its value to health care professionals: content is highly distributed and difficult to find, clinical information is not separated from non-clinical information, and the current Web technology is unable to support some advanced retrieval capabilities. A system called CliniWeb has been developed to address these problems. CliniWeb is an index to clinical information on the World Wide Web, providing a browsing and searching interface to clinical content at the level of the health care student or provider. Its database contains a list of clinical information resources on the Web that are indexed by terms from the Medical Subject Headings disease tree and retrieved with the assistance of SAPHIRE. Limitations of the processes used to build the database are discussed, together with directions for future research.

Tribological performance of quaternary CrSiCN coatings under dry and lubricated conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lorenzo-Martin, C.; Ajayi, O.; Erdemir, A.

This paper presents an experimental study of friction and wear performance of quaternary CrSiCN coatings deposited on a hardened H-13 steel substrate by a plasma enhanced magnetron sputtering (PEMS) technique. Friction and wear tests were conducted with a reciprocating line contact between a hardened 4370 steel roller and coated and uncoated flat specimens under dry and lubricated conditions. The effects of coating thickness (1, 3.5 and 7.5 μm) on the mechanical properties, friction and wear performance were also assessed. In dry sliding, the friction of coated surfaces was about the same as for uncoated surfaces, except for the 1-μm coating,more » which had higher friction. Friction for coated surfaces under lubricated contact was in general higher than for uncoated surfaces. There was no measurable wear on any of the coated surfaces, under either dry or lubricated conditions. However, wear was higher on the steel roller counterface sliding against the coated surfaces, with the amount of wear proportional to the mating coating thickness. The effectiveness of formulated lubricant additives was also modified by the coating, resulting in major effects on friction and wear behavior. Finally, this reduction in lubricant additive efficacy is due to the fact that the additives were designed and optimized for ferrous surfaces.« less

Tribological performance of quaternary CrSiCN coatings under dry and lubricated conditions

DOE PAGES

Lorenzo-Martin, C.; Ajayi, O.; Erdemir, A.; ...

2017-06-15

This paper presents an experimental study of friction and wear performance of quaternary CrSiCN coatings deposited on a hardened H-13 steel substrate by a plasma enhanced magnetron sputtering (PEMS) technique. Friction and wear tests were conducted with a reciprocating line contact between a hardened 4370 steel roller and coated and uncoated flat specimens under dry and lubricated conditions. The effects of coating thickness (1, 3.5 and 7.5 μm) on the mechanical properties, friction and wear performance were also assessed. In dry sliding, the friction of coated surfaces was about the same as for uncoated surfaces, except for the 1-μm coating,more » which had higher friction. Friction for coated surfaces under lubricated contact was in general higher than for uncoated surfaces. There was no measurable wear on any of the coated surfaces, under either dry or lubricated conditions. However, wear was higher on the steel roller counterface sliding against the coated surfaces, with the amount of wear proportional to the mating coating thickness. The effectiveness of formulated lubricant additives was also modified by the coating, resulting in major effects on friction and wear behavior. Finally, this reduction in lubricant additive efficacy is due to the fact that the additives were designed and optimized for ferrous surfaces.« less

Electron beam physical vapor deposition of YSZ electrolyte coatings for SOFCs

NASA Astrophysics Data System (ADS)

He, Xiaodong; Meng, Bin; Sun, Yue; Liu, Bochao; Li, Mingwei

2008-09-01

YSZ electrolyte coatings were prepared by electron beam physical vapor deposition (EB-PVD) at a high deposition rate of up to 1 μm/min. The YSZ coating consisted of a single cubic phase and no phase transformation occurred after annealing treatment at 1000 °C. A typical columnar structure was observed in this coating by SEM and feather-like characteristics appeared in every columnar grain. In columnar grain boundaries there were many micron-sized gaps and pores. In TEM image, many white lines were found, originating from the alignment of nanopores existing within feather-like columnar grains. The element distribution along the cross-section of the coating was homogeneous except Zr with a slight gradient. The coating exhibited a characteristic anisotropic behavior in electrical conductivity. In the direction perpendicular to coating surface the electrical conductivity was remarkably higher than that in the direction parallel to coating surface. This mainly attributed to the typical columnar structure for EB-PVD coating and the existence of many grain boundaries along the direction parallel to coating surface. For as-deposited coating, the gas permeability coefficient of 9.78 × 10 -5 cm 4 N -1 s -1 was obtained and this value was close to the critical value of YSZ electrolyte layer required for solid oxide fuel cell (SOFC) operation.

Nanoscale View of Dewetting and Coating on Partially Wetted Solids.

PubMed

Deng, Yajun; Chen, Lei; Liu, Qiao; Yu, Jiapeng; Wang, Hao

2016-05-19

There remain significant gaps in our ability to predict dewetting and wetting despite the extensive study over the past century. An important reason is the absence of nanoscopic knowledge about the processes near the moving contact line. This experimental study for the first time obtained the liquid morphology within 10 nm of the contact line, which was receding at low speed (U < 50 nm/s). The results put an end to long-standing debate about the microscopic contact angle, which turned out to be varying with the speed as opposed to the constant-angle assumption that has been frequently employed in modeling. Moreover, a residual film of nanometer thickness ubiquitously remained on the solid after the receding contact line passed. This microscopic residual film modified the solid surface and thus made dewetting far from a simple reverse of wetting. A complete scenario for dewetting and coating is provided.

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Method 204A or 204F of appendix M to 40 CFR part 51 to determine the mass fraction of TVH liquid input... the capture efficiency test run, kg. TVHi = Mass fraction of TVH in regulated material, i, that is... protocol compares the mass of liquid TVH in regulated materials applied in the web coating/printing or...

40 CFR 63.4361 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Method 204A or 204F of appendix M to 40 CFR part 51 to determine the mass fraction of TVH liquid input... the capture efficiency test run, kg. TVHi = Mass fraction of TVH in regulated material, i, that is... protocol compares the mass of liquid TVH in regulated materials applied in the web coating/printing or...

76 FR 42560 - Approval and Promulgation of Air Quality Implementation Plans; Vermont; Reasonably Available...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-19

... 2006, EPA-453/R-06-003) 3. Paper, Film, and Foil Coatings (September 2007, EPA-453/R-07- 003) 4. Metal....regulations.gov Web site is an ``anonymous access'' system, which means EPA will not know your identity or... is not publicly available, i.e., CBI or other information whose disclosure is restricted by statute...

Characterization of the coating and tablet core roughness by means of 3D optical coherence tomography.

PubMed

Markl, Daniel; Wahl, Patrick; Pichler, Heinz; Sacher, Stephan; Khinast, Johannes G

2018-01-30

This study demonstrates the use of optical coherence tomography (OCT) to simultaneously characterize the roughness of the tablet core and coating of pharmaceutical tablets. OCT is a high resolution non-destructive and contactless imaging methodology to characterize structural properties of solid dosage forms. Besides measuring the coating thickness, it also facilitates the analysis of the tablet core and coating roughness. An automated data evaluation algorithm extracts information about coating thickness, as well as tablet core and coating roughness. Samples removed periodically from a pan coating process were investigated, on the basis of thickness and profile maps of the tablet core and coating computed from about 480,000 depth measurements (i.e., 3D data) per sample. This data enables the calculation of the root mean square deviation, the skewness and the kurtosis of the assessed profiles. Analyzing these roughness parameters revealed that, for the given coating formulation, small valleys in the tablet core are filled with coating, whereas coarse features of the tablet core are still visible on the final film-coated tablet. Moreover, the impact of the tablet core roughness on the coating thickness is analyzed by correlating the tablet core profile and the coating thickness map. The presented measurement method and processing could be in the future transferred to in-line OCT measurements, to investigate core and coating roughness during the production of film-coated tablets. Copyright © 2017. Published by Elsevier B.V.

Ultrafast web inspection with hybrid dispersion laser scanner.

PubMed

Chen, Hongwei; Wang, Chao; Yazaki, Akio; Kim, Chanju; Goda, Keisuke; Jalali, Bahram

2013-06-10

We report an ultrafast web inspector that operates at a 1000 times higher scan rate than conventional methods. This system is based on a hybrid dispersion laser scanner that performs line scans at nearly 100 MHz. Specifically, we demonstrate web inspection with detectable resolution of 48.6 μm/pixel (scan direction) × 23 μm (web flow direction) within a width of view of 6 mm at a record high scan rate of 90.9 MHz. We demonstrate the identification and evaluation of particles on silicon wafers. This method holds great promise for speeding up quality control and hence reducing manufacturing costs.

Audiovisual Speech Web-Lab: an Internet teaching and research laboratory.

PubMed

Gordon, M S; Rosenblum, L D

2001-05-01

Internet resources now enable laboratories to make full-length experiments available on line. A handful of existing web sites offer users the ability to participate in experiments and generate usable data. We have integrated this technology into a web site that also provides full discussion of the theoretical and methodological aspects of the experiments using text and simple interactive demonstrations. The content of the web site (http://www.psych.ucr.edu/avspeech/lab) concerns audiovisual speech perception and its relation to face perception. The site is designed to be useful for users of multiple interests and levels of expertise.

Multiparameter cell affinity chromatography: separation and analysis in a single microfluidic channel.

PubMed

Li, Peng; Gao, Yan; Pappas, Dimitri

2012-10-02

The ability to sort and capture more than one cell type from a complex sample will enable a wide variety of studies of cell proliferation and death and the analysis of disease states. In this work, we integrated a pneumatic actuated control layer to an affinity separation layer to create different antibody-coating regions on the same fluidic channel. The comparison of different antibody capture capabilities to the same cell line was demonstrated by flowing Ramos cells through anti-CD19- and anti-CD71-coated regions in the same channel. It was determined that the cell capture density on the anti-CD19 region was 2.44 ± 0.13 times higher than that on the anti-CD71-coated region. This approach can be used to test different affinity molecules for selectivity and capture efficiency using a single cell line in one separation. Selective capture of Ramos and HuT 78 cells from a mixture was also demonstrated using two antibody regions in the same channel. Greater than 90% purity was obtained on both capture areas in both continuous flow and stop flow separation modes. A four-region antibody-coated device was then fabricated to study the simultaneous, serial capture of three different cell lines. In this case the device showed effective capture of cells in a single separation channel, opening up the possibility of multiple cell sorting. Multiparameter sequential blood sample analysis was also demonstrated with high capture specificity (>97% for both CD19+ and CD4+ leukocytes). The chip can also be used to selectively treat cells after affinity separation.

40 CFR Table 2 to Subpart Kkkk of... - Emission Limits for Existing Affected Sources

Code of Federal Regulations, 2010 CFR

2010-07-01

... coating a. Two-piece beverage cans—all coatingsb. Two-piece food cans—all coatings c. One-piece aerosol.... Three-piece can assembly a. Inside spray 0.29 (2.43). b. Aseptic side seam stripes on food cans 1.94 (16.16). c. Nonaseptic side seam stripes on food cans 0.79 (6.57). d. Side seam stripes on general line...

Automated array assembly task, phase 1

NASA Technical Reports Server (NTRS)

Carbajal, B. G.

1977-01-01

Various aspects of a sensitivity analysis, in particular, the impact of variations in metal sheet resistivity, metal line width, diffused layer sheet resistance, junction depth, base layer lifetime, optical coating thickness and optical coating refractive index and on process reproducibility for A's diffusion from a polymer dopant source and on module fabrication were studied. Model calculations show that acceptable process windows exist for each of these parameters.

On-Line Literature: The Challenge of Integrating Web-Based Materials

ERIC Educational Resources Information Center

Ruzich, Constance M.

2012-01-01

This classroom research discusses the challenges of integrating face-to-face interactions with the use of on-line resources in secondary English classrooms. Examining the lesson plans of pre-service and early career teachers in the US, I found that the uses of on-line resources were frequently neither coherent nor consistent with the goals and…

Report: Controls and Oversight Needed to Improve Administration of EPA’s Customer Service Lines

EPA Pesticide Factsheets

Report #13-P-0432, September 26, 2013. The EPA has a variety of resources—including telephone hotlines, Web clearinghouses, and other online reference information—which the OIG has categorized as customer service lines (CSLs).

Surface-charge-dependent cell localization and cytotoxicity of cerium oxide nanoparticles.

PubMed

Asati, Atul; Santra, Santimukul; Kaittanis, Charalambos; Perez, J Manuel

2010-09-28

Cerium oxide nanoparticles (nanoceria) have shown great potential as antioxidant and radioprotective agents for applications in cancer therapy. Recently, various polymer-coated nanoceria preparations have been developed to improve their aqueous solubility and allow for surface functionalization of these nanoparticles. However, the interaction of polymer-coated nanoceria with cells, their uptake mechanism, and subcellular localization are poorly understood. Herein, we engineered polymer-coated cerium oxide nanoparticles with different surface charges (positive, negative, and neutral) and studied their internalization and toxicity in normal and cancer cell lines. The results showed that nanoceria with a positive or neutral charge enters most of the cell lines studied, while nanoceria with a negative charge internalizes mostly in the cancer cell lines. Moreover, upon entry into the cells, nanoceria is localized to different cell compartments (e.g., cytoplasm and lysosomes) depending on the nanoparticle's surface charge. The internalization and subcellular localization of nanoceria plays a key role in the nanoparticles' cytotoxicity profile, exhibiting significant toxicity when they localize in the lysosomes of the cancer cells. In contrast, minimal toxicity is observed when they localize into the cytoplasm or do not enter the cells. Taken together, these results indicate that the differential surface-charge-dependent localization of nanoceria in normal and cancer cells plays a critical role in the nanoparticles' toxicity profile.

Fault location method for unexposed gas trunk line insulation at stray current constant effect area

NASA Astrophysics Data System (ADS)

Tsenev, A. N.; Nosov, V. V.; Akimova, E. V.

2017-10-01

For the purpose of gas trunk lines safe operation, two types of pipe wall metal anticorrosion protection are generally used - the passive (insulation coating) protection and the active (electrochemical) protection. In the process of a pipeline long-term operation, its insulation is subject to wear and damage. Electrochemical protection means of a certain potential value prevent metal dissolution in the soil. When insulation wear and tear attains a level of insufficiency of the protection potential value, the insulating coating needs repair which is a labor-consuming procedure. To reduce the risk of such situation, it is necessary to make inspection rounds to monitor the condition of pipe insulation. A method for pipeline insulation coating unexposed fault location based on Pearson method is considered, wherein a working cathodic protection station signal of 100 Hz frequency is used, which makes installation of a generator unnecessary, and also a specific generator signal of 1 kHz frequency is used at high noise immunity and sensitivity of the instrument complex. This method enables detection and sizing of unexposed pipeline defects within the zones of earth current permanent action. High noise immunity of selective indicators allows for operation in proximity to 110 kV, 220 kV, and 500 kV power transmission lines in action.

Development and characterization of polymer-coated liposomes for vaginal delivery of sildenafil citrate.

PubMed

Refai, Hanan; Hassan, Doaa; Abdelmonem, Rehab

2017-11-01

Vaginal administration of sildenafil citrate has shown recently to develop efficiently the uterine lining with subsequent successful embryo implantation following in vitro fertilization. The aim of the present study was to develop sildenafil-loaded liposomes coated with bioadhesive polymers for enhanced vaginal retention and improved drug permeation. Three liposomal formulae were prepared by thin-film method using different phospholipid:cholesterol ratios. The optimal liposomal formulation was coated with bioadhesive polymers (chitosan and HPMC). A marked increase in liposomal size and zeta potential was observed for all coated liposomal formulations. HPMC-coated liposomes showed the greater bioadhesion and higher entrapment efficiency than chitosan-coated formulae. The in vitro release studies showed prolonged release of sildenafil from coated liposomes as compared to uncoated liposomes and sildenafil solution. Ex vivo permeation study revealed the enhanced permeation of coated relative to uncoated liposomes. Chitosan-coated formula demonstrated highest drug permeation and was thus selected for further investigations. Transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FTIR) confirmed the successful coating of the liposomes by chitosan. Histopathological in vivo testing proved the efficacy of chitosan-coated liposomes to improve blood flow to the vaginal endometrium and to increase endometrial thickness. Chitosan-coated liposomes can be considered as potential novel drug delivery system intended for the vaginal administration of sildenafil, which would prolong system's retention at the vaginal site and enhance the permeation of sildenafil to uterine blood circulation.

Solar Lyman-Alpha Polarization Observation of the Chromosphere and Transition Region by the Sounding Rocket Experiment CLASP

NASA Technical Reports Server (NTRS)

Narukage, Noriyuki; Kano, Ryohei; Bando, Takamasa; Ishikawa, Ryoko; Kubo, Masahito; Katsukawa, Yukio; Ishikawa, Shinnosuke; Hara, Hiroshi; Suematsu, Yoshinori; Giono, Gabriel;

Citrus psorosis virus coat protein-derived hairpin construct confers stable transgenic resistance in citrus against psorosis A and B syndromes.

PubMed

De Francesco, A; Costa, N; García, M L

2017-04-01

Citrus psorosis virus (CPsV) is the causal agent of psorosis, a serious and widespread citrus disease. Two syndromes of psorosis, PsA and PsB, have been described. PsB is the most aggressive and rampant form. Previously, we obtained Pineapple sweet orange plants transformed with a hairpin construct derived from the CPsV coat protein gene (ihpCP). Some of these plants were resistant to CPsV 90-1-1, a PsA isolate homologous to the transgene. In this study, we found that expression of the ihpCP transgene and siRNA production in lines ihpCP-10 and -15 were stable with time and propagation. In particular, line ihpCP-15 has been resistant for more than 2 years, even after re-inoculation. The ihpCP plants were also resistant against a heterologous CPsV isolate that causes severe PsB syndrome. Line ihpCP-15 manifested complete resistance while line ihpCP-10 was tolerant to the virus, although with variable behaviour, showing delay and attenuation in PsB symptoms. These lines are promising for a biotech product aimed at eradicating psorosis.

76 FR 68301 - Airworthiness Directives; Bell Helicopter Textron, Inc. (Bell), Model 205A-1, 205B, 210, and 212...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... the inspection area for any edge delamination, as indicated by a dark line located along any bond line... docket Web site, you can find and read the comments to any of our dockets, including the name of the... indicated by a dark line located along any bond line, or a crack in the paint finish. An edge delamination...

Software framework for the upcoming MMT Observatory primary mirror re-aluminization

NASA Astrophysics Data System (ADS)

Gibson, J. Duane; Clark, Dusty; Porter, Dallan

2014-07-01

Details of the software framework for the upcoming in-situ re-aluminization of the 6.5m MMT Observatory (MMTO) primary mirror are presented. This framework includes: 1) a centralized key-value store and data structure server for data exchange between software modules, 2) a newly developed hardware-software interface for faster data sampling and better hardware control, 3) automated control algorithms that are based upon empirical testing, modeling, and simulation of the aluminization process, 4) re-engineered graphical user interfaces (GUI's) that use state-of-the-art web technologies, and 5) redundant relational databases for data logging. Redesign of the software framework has several objectives: 1) automated process control to provide more consistent and uniform mirror coatings, 2) optional manual control of the aluminization process, 3) modular design to allow flexibility in process control and software implementation, 4) faster data sampling and logging rates to better characterize the approximately 100-second aluminization event, and 5) synchronized "real-time" web application GUI's to provide all users with exactly the same data. The framework has been implemented as four modules interconnected by a data store/server. The four modules are integrated into two Linux system services that start automatically at boot-time and remain running at all times. Performance of the software framework is assessed through extensive testing within 2.0 meter and smaller coating chambers at the Sunnyside Test Facility. The redesigned software framework helps ensure that a better performing and longer lasting coating will be achieved during the re-aluminization of the MMTO primary mirror.

HYGROMETER

DOEpatents

Stover, C.M.

1963-01-29

This pntent relates to a hygrometer having a rapid and essentially straight line response to changes in relntive humidity and a high degree of sensitivity to moisture in the low relative humiaity range. In particular, the hygrometer comprises a metal plate coated with a hygrometric oxide coating, and electrical leads coupled to the metal plate and the oxide coating, respectively. When a change in relative humidity occurs, a change in the resistance and capacitance between the leads takes place owing to the hygrometric action of the oxide coating. Thus, with a voltage being applied to the leads, a change in capacitance and resistance between them causes a proportional change in the current between the leads. This may be read upon a suitable indicator for determining the relative humidity at any given instant. (AEC)

Pressure Vessel with Impact and Fire Resistant Coating and Method of Making Same

NASA Technical Reports Server (NTRS)

DeLay, Thomas K. (Inventor)

2005-01-01

An impact and fire resistant coating laminate is provided which serves as an outer protective coating for a pressure vessel such as a composite overwrapped vessel with a metal lining. The laminate comprises a plurality of fibers (e.g., jute twine or other, stronger fibers) which are wound around the pressure vessel and an epoxy matrix resin for the fibers. The epoxy matrix resin including a plurality of microspheres containing a temperature responsive phase change material which changes phase in response to exposure thereof to a predetermined temperature increase so as to afford increased insulation and hear absorption.

Pressure vessel with impact and fire resistant coating and method of making same

NASA Technical Reports Server (NTRS)

DeLay, Thomas K. (Inventor)

2005-01-01

An impact and fire resistant coating laminate is provided which serves as an outer protective coating for a pressure vessel such as a composite overwrapped vessel with a metal lining. The laminate comprises a plurality of fibers (e.g., jute twine or other, stronger fibers) which are wound around the pressure vessel and an epoxy matrix resin for the fibers. The epoxy matrix resin including a plurality of microspheres containing a temperature responsive phase change material which changes phase in response to exposure thereof to a predetermined temperature increase so as to afford increased insulation and heat absorption.

42 CFR 423.128 - Dissemination of Part D plan information.

Code of Federal Regulations, 2011 CFR

2011-10-01

... plan sponsor's toll free customer service line or by accessing the plan sponsor's internet Web site. (8... redetermination processes via an Internet Web site; and (iii) A system that transmits codes to network pharmacies...— (1) A toll-free customer call center that— (i) Is open during usual business hours. (ii) Provides...

The New Frontier: Conquering the World Wide Web by Mule.

ERIC Educational Resources Information Center

Gresham, Morgan

1999-01-01

Examines effects of teaching hypertext markup language on students' perceptions of class goals in a networked composition classroom. Suggests sending documents via file transfer protocol by command line and viewing the Web with a textual browser shifted emphasis from writing to coding. Argues that helping students identify a balance between…

Weaving a Syllaweb: Consideration before Constructing an On-line Syllabus.

ERIC Educational Resources Information Center

Johnston, Joyce P.

This paper explores the practical and philosophical issues involved in Web site construction so that the finished site truly reflects its creator. The author uses the term "syllaweb" for a hyperlinked syllabus and declares that it was an outgrowth of Vannevar Bush's original description of computerized graphical communication as a web,…

Designing a Web Site to Share Information with Parents

ERIC Educational Resources Information Center

Englund, Lillian White

2009-01-01

This article discusses the development and use of an on-line portfolio process. It presents a background rationale for the need and effectiveness of a communication tool that supports the use of the portfolio process throughout the education of a child with identified disabilities. The process for developing the individualized Web page is…

Sustained release vancomycin-coated titanium alloy using a novel electrostatic dry powder coating technique may be a potential strategy to reduce implant-related infection.

PubMed

Han, Jing; Yang, Yi; Lu, Junren; Wang, Chenzhong; Xie, Youtao; Zheng, Xuebin; Yao, Zhenjun; Zhang, Chi

2017-07-24

In order to tackle the implant-related infection, a novel way was developed in this study to coat vancomycin particles mixed with controlled release coating materials onto the surface of titanium alloy by using an electrostatic dry powder coating technique. To characterize this sustained release antibacterial coating, surface morphology, in vitro and in vivo drug release were sequentially evaluated. In vitro cytotoxicity was tested by Cell Counting Kit-8 (CCK-8) assay and cytological changes were observed by inverted microscope. The antibacterial properties against MRSA, including a bacterial growth inhibition assay and a colony-counting test by spread plate method were performed. Results indicated that the vancomycin-coated sample was biocompatible for Human osteoblast cell line MG-63 and displayed effective antibacterial ability against MRSA. The coating film was revealed uniform by scanning electron microscopy. Both the in vitro and in vivo drug release kinetics showed an initially high release rate, followed by an extended period of sustained drug release over 7 days. These results suggest that with good biocompatibility and antibacterial ability, the sustained release antibacterial coating of titanium alloy using our novel electrostatic dry powder coating process may provide a promising candidate for the treatment of orthopedic implant-related infection.

Comparative analysis of electrophysical properties of ceramic tantalum pentoxide coatings, deposited by electron beam evaporation and magnetron sputtering methods

NASA Astrophysics Data System (ADS)

Donkov, N.; Mateev, E.; Safonov, V.; Zykova, A.; Yakovin, S.; Kolesnikov, D.; Sudzhanskaya, I.; Goncharov, I.; Georgieva, V.

2014-12-01

Ta2O5 ceramic coatings have been deposited on glass substrates by e-beam evaporation and magnetron sputtering methods. For the magnetron sputtering process Ta target was used. X-ray diffraction measurements show that these coatings are amorphous. XPS survey spectra of the ceramic Ta2O5 coatings were obtained. All spectra consist of well-defined XPS lines of Ta 4f, 4d, 4p and 4s; O 1s; C 1s. Ta 4f doublets are typical for Ta2O5 coatings with two main peaks. Scanning electron microscopy and atomic force microscopy images of the e-beam evaporated and magnetron sputtered Ta2O5 ceramic coatings have revealed a relatively flat surface with no cracks. The dielectric properties of the tantalum pentoxide coatings have been investigated in the frequency range of 100 Hz to 1 MHz. The electrical behaviour of e-beam evaporated and magnetron sputtered Ta2O5 ceramic coatings have also been compared. The deposition process conditions principally effect the structure parameters and electrical properties of Ta2O5 ceramic coatings. The coatings deposited by different methods demonstrate the range of dielectric parameters due to the structural and stoichiometric composition changes

NASA Tech Briefs, March 2005

NASA Technical Reports Server (NTRS)

2005-01-01

Topics covered include: Scheme for Entering Binary Data Into a Quantum Computer; Encryption for Remote Control via Internet or Intranet; Coupled Receiver/Decoders for Low-Rate Turbo Codes; Processing GPS Occultation Data To Characterize Atmosphere; Displacing Unpredictable Nulls in Antenna Radiation Patterns; Integrated Pointing and Signal Detector for Optical Receiver; Adaptive Thresholding and Parameter Estimation for PPM; Data-Driven Software Framework for Web-Based ISS Telescience; Software for Secondary-School Learning About Robotics; Fuzzy Logic Engine; Telephone-Directory Program; Simulating a Direction-Finder Search for an ELT; Formulating Precursors for Coating Metals and Ceramics; Making Macroscopic Assemblies of Aligned Carbon Nanotubes; Ball Bearings Equipped for In Situ Lubrication on Demand; Synthetic Bursae for Robots; Robot Forearm and Dexterous Hand; Making a Metal-Lined Composite-Overwrapped Pressure Vessel; Ex Vivo Growth of Bioengineered Ligaments and Other Tissues; Stroboscopic Goggles for Reduction of Motion Sickness; Articulating Support for Horizontal Resistive Exercise; Modified Penning-Malmberg Trap for Storing Antiprotons; Tumbleweed Rovers; Two-Photon Fluorescence Microscope for Microgravity Research; Biased Randomized Algorithm for Fast Model-Based Diagnosis; Fast Algorithms for Model-Based Diagnosis; Simulations of Evaporating Multicomponent Fuel Drops; Formation Flying of Tethered and Nontethered Spacecraft; and Two Methods for Efficient Solution of the Hitting- Set Problem.

76 FR 68166 - Discontinuing the Mass Mailing of Paper Fee Schedules to Registered Attorneys, Agents, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-03

... current fee schedule is essentially built into the on-line systems (e.g., EFS-Web, TEAS, accessible... applications are filed on-line via TEAS. The official, current USPTO fee schedule will continue to be available...

Web-based multimedia information retrieval for clinical application research

NASA Astrophysics Data System (ADS)

Cao, Xinhua; Hoo, Kent S., Jr.; Zhang, Hong; Ching, Wan; Zhang, Ming; Wong, Stephen T. C.

2001-08-01

We described a web-based data warehousing method for retrieving and analyzing neurological multimedia information. The web-based method supports convenient access, effective search and retrieval of clinical textual and image data, and on-line analysis. To improve the flexibility and efficiency of multimedia information query and analysis, a three-tier, multimedia data warehouse for epilepsy research has been built. The data warehouse integrates clinical multimedia data related to epilepsy from disparate sources and archives them into a well-defined data model.

Protective immune response of chickens to oral vaccination with thermostable live Fowlpox virus vaccine (strain TPV-1) coated on oiled rice.

PubMed

Wambura, Philemon N; Godfrey, S K

2010-03-01

The objective of the present study was to develop and evaluate a local vaccine (strain TPV-1) against Fowl pox (FP) in chickens. Two separate groups of chickens were vaccinated with FP vaccine through oral (coated on oiled rice) and wing web stab routes, respectively. The results showed that the haemagglutination-inhibition (HI) antibody titres in both vaccinated groups were comparable and significantly higher (P < 0.05) than the control chickens. It was further revealed that 14 days after vaccination HI GMT of > or =2 log(2) was recorded in chickens vaccinated by oral and wing web stab routes whereas 35 days after vaccination the HI antibody titres reached 5.6 log(2) and 6.3 log(2), respectively. Moreover, in both groups the birds showed 100% protection against challenge virus at 35 days after vaccination. The findings from the present study have shown that oral route is equally effective as wing web stab route for vaccination of chickens against FP. However, the oral route can be used in mass vaccination of birds thus avoid catching individual birds for vaccination. It was noteworthy that strain TPV-1 virus could be propagated by a simple allantoic cavity inoculation and harvesting of allantoic fluid where it survived exposure at 57 degrees C for 2 hours. If the oral vaccination technique is optimized it may be used in controlling FP in scavenging and feral chickens. In conclusion, the present study has shown that FP vaccine (strain TPV-1) was safe, thermostable, immunogenic and efficacious in vaccinated chickens.

Modified corrosion protection coatings for Concrete tower of Transmission line

NASA Astrophysics Data System (ADS)

Guo, Kai; Jing, Xiangyang; Wang, Hongli; Yue, Zengwu; Wu, Yaping; Mi, Xuchun; Li, Xingeng; Chen, Suhong; Fan, Zhibin

2017-12-01

By adding nano SiO2 particles, an enhanced K-PRTV anti-pollution flashover coating had been prepared. Optical profile meter (GT-K), atomic force microscopy (AFM) and infrared spectrometer (FT-IR) characterization were carried out on the coating surface analysis. With the use of modified epoxy resin as the base material, the supplemented by phosphate as a corrosion stabilizer, to achieve a corrosion of steel and galvanized steel with rust coating. Paint with excellent adhesion, more than 10MPa (1), resistant to neutral salt spray 1000h does not appear rust point. At the same time coating a large amount of ultra-fine zinc powder can be added for the tower galvanized layer zinc repair function, while the paint in the zinc powder for the tower to provide sacrificial anode protection, to achieve self-repair function of the coating. Compared to the market with a significant reduction in the cost of rust paint, enhance the anti-corrosion properties.

Legibility Evaluation Using Point-of-regard Measurement

NASA Astrophysics Data System (ADS)

Saito, Daisuke; Saito, Keiichi; Saito, Masao

Web site visibility has become important because of the rapid dissemination of World Wide Web, and combinations of foreground and background colors are crucial in providing high visibility. In our previous studies, the visibilities of several web-safe color combinations were examined using a psychological method. In those studies, simple stimuli were used because of experimental restriction. In this paper, legibility of sentences on web sites was examined using a psychophisiological method, point-of-regard measurement, to obtain other practical data. Ten people with normal color sensations ranging from ages 21 to 29 were recruited. The number of characters per line in each page was arranged in the same number, and the four representative achromatic web-safe colors, that is, #000000, #666666, #999999 and #CCCCCC, were examined. The reading time per character and the gaze time per line were obtained from point-of-regard measurement, and the normalized with the reading time and the gaze time of the three colors were calculated and compared. As the results, it was shown that the time of reading and gaze become long at the same ratio when the contrast decreases by point-of-regard measurement. Therefore, it was indicated that the legibility of color combinations could be estimated by point-of-regard measurement.

Carbon nanotube-coating accelerated cell adhesion and proliferation on poly (L-lactide)

NASA Astrophysics Data System (ADS)

Hirata, Eri; Akasaka, Tsukasa; Uo, Motohiro; Takita, Hiroko; Watari, Fumio; Yokoyama, Atsuro

2012-12-01

The surface of a polylactic acid (PLLA) was coated multiwalled carbon nanotubes (MWCNTs) in order to improve the surface properties. In addition, its surface characteristics and cell culturing properties were examined. Whole surface of PLLA was homogeneously covered by MWCNTs maintained a unique tubular structure. MWCNT-coated PLLA showed remarkable higher wettability than uncoated PLLA. Human osteosarcoma cell line (Saos2) adhered well on the CNT-coated PLLA whereas there are few cells attached on the uncoated PLLA at 2 h after seeding. The number of the cells on uncoated PLLA was still smaller than on the MWCNT-coated PLLA at 1 and 3 days. Moreover, The DNA content in the cells attached to the MWCNT-coated PLLA was significantly higher than that on the uncoated PLLA (p < 0.05) at 1 and 3 days. There was no significant difference between the scaffolds for ALP activity normalized by DNA content at both term (p > 0.1). Therefore MWCNT-coating on PLLA improved the surface wettability and initial cell attachment at early stage.

Put the lid on VOC emissions from maintenance coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, R.E.

1996-11-01

After the coating film is applied to the substrate, the solvents evaporate and generally become an environmental liability. Solvents used by the coatings industry have been a major environmental issue for many years. Over the years, regulations have been aimed at reducing or eliminating photochemically reactive solvents--those that react in the atmosphere with nitrogen oxides in the atmosphere with nitrogen oxides in the presence of sunlight and heat to form ozones. Many of the solvents used in the coatings industry are, in fact, photochemically reactive. The rules regulating the maintenance coatings industry can generally be divided into three categories: 1.more » Rules aimed at restricting the VOCs in steel fabricating shops and paint shops. 2. Rules aimed at regulating the emission of VOCs from coatings applied in the field such as on bridges or industrial structures. 3. Rules aimed at the shipbuilding industry where coatings are applied to marine vessels. The paper discusses reducing VOCs, penetrating sealers, mastics, tank linings, inorganic zincs, topcoats--waterborne acrylics, zero-VOC urethane/water systems, and solventless topcoats.« less

Naturally inspired SERS substrates fabricated by photocatalytically depositing silver nanoparticles on cicada wings

PubMed Central

2014-01-01

Densely stacked Ag nanoparticles with an average diameter of 199 nm were effectively deposited on TiO2-coated cicada wings (Ag/TiO2-coated wings) from a water-ethanol solution of AgNO3 using ultraviolet light irradiation at room temperature. It was seen that the surfaces of bare cicada wings contained nanopillar array structures. In the optical absorption spectra of the Ag/TiO2-coated wings, the absorption peak due to the localized surface plasmon resonance (LSPR) of Ag nanoparticles was observed at 440 nm. Strong Surface-enhanced Raman scattering (SERS) signals of Rhodamine 6G adsorbed on the Ag/TiO2-coated wings were clearly observed using the 514.5-nm line of an Ar+ laser. The Ag/TiO2-coated wings can be a promising candidate for naturally inspired SERS substrates. PMID:24959110

Naturally inspired SERS substrates fabricated by photocatalytically depositing silver nanoparticles on cicada wings

NASA Astrophysics Data System (ADS)

Tanahashi, Ichiro; Harada, Yoshiyuki

2014-06-01

Densely stacked Ag nanoparticles with an average diameter of 199 nm were effectively deposited on TiO2-coated cicada wings (Ag/TiO2-coated wings) from a water-ethanol solution of AgNO3 using ultraviolet light irradiation at room temperature. It was seen that the surfaces of bare cicada wings contained nanopillar array structures. In the optical absorption spectra of the Ag/TiO2-coated wings, the absorption peak due to the localized surface plasmon resonance (LSPR) of Ag nanoparticles was observed at 440 nm. Strong Surface-enhanced Raman scattering (SERS) signals of Rhodamine 6G adsorbed on the Ag/TiO2-coated wings were clearly observed using the 514.5-nm line of an Ar+ laser. The Ag/TiO2-coated wings can be a promising candidate for naturally inspired SERS substrates.

Plasma-sprayed, self-lubricating coatings for use from cryogenic temperatures to 870 deg C (1600 deg F)

NASA Technical Reports Server (NTRS)

Sliney, H. E.

1975-01-01

A plasma-sprayed coating is described with good lubricating properties over a wide temperature range. The coating, designated NASA LUBE PS101, contains silver, nichrome, calcium fluoride, and an oxidation protective glass. Oscillating tests were conducted of self-aligning, plain cylindrical bearings, in which the bore was lined with 0.025 cm (0.010 in.) thick coatings of PS101; these were conducted at a radial load of 3.5 x 10 to the 7th power N/sq m (5000 psi) in nitrogen gas at -107 C (-160 F), in vacuum at room temperature, and in air from room temperature to 870 C (1600 F). Friction coefficients were less than 0.25 in all cases and wear rates were low. The coating is not brittle, and it has adequate oxidation resistance in air to at least 870 C.

40 CFR 63.4300 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... which you use the emission rate without add-on controls option, as specified in § 63.4291(a)(2) or (c)(2... with add-on controls option, as specified in § 63.4291(a)(3) or (c)(3), and any web coating/printing... must be in compliance with the operating limits for emission capture systems and add-on control devices...

40 CFR 63.4300 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... which you use the emission rate without add-on controls option, as specified in § 63.4291(a)(2) or (c)(2... with add-on controls option, as specified in § 63.4291(a)(3) or (c)(3), and any web coating/printing... must be in compliance with the operating limits for emission capture systems and add-on control devices...

40 CFR 63.4300 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... which you use the emission rate without add-on controls option, as specified in § 63.4291(a)(2) or (c)(2... with add-on controls option, as specified in § 63.4291(a)(3) or (c)(3), and any web coating/printing... must be in compliance with the operating limits for emission capture systems and add-on control devices...

40 CFR 63.4300 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... which you use the emission rate without add-on controls option, as specified in § 63.4291(a)(2) or (c)(2... with add-on controls option, as specified in § 63.4291(a)(3) or (c)(3), and any web coating/printing... must be in compliance with the operating limits for emission capture systems and add-on control devices...

40 CFR 63.4300 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... which you use the emission rate without add-on controls option, as specified in § 63.4291(a)(2) or (c)(2... with add-on controls option, as specified in § 63.4291(a)(3) or (c)(3), and any web coating/printing... must be in compliance with the operating limits for emission capture systems and add-on control devices...

Single Layer Broadband Anti-Reflective Coatings for Plastic Substrates Produced by Full Wafer and Roll-to-Roll Step-and-Flash Nano-Imprint Lithography

PubMed Central

Burghoorn, Marieke; Roosen-Melsen, Dorrit; de Riet, Joris; Sabik, Sami; Vroon, Zeger; Yakimets, Iryna; Buskens, Pascal

2013-01-01

Anti-reflective coatings (ARCs) are used to lower the reflection of light on the surface of a substrate. Here, we demonstrate that the two main drawbacks of moth eye-structured ARCs—i.e., the lack of suitable coating materials and a process for large area, high volume applications—can be largely eliminated, paving the way for cost-efficient and large-scale production of durable moth eye-structured ARCs on polymer substrates. We prepared moth eye coatings on polymethylmethacrylate (PMMA) and polycarbonate using wafer-by-wafer step-and-flash nano-imprint lithography (NIL). The reduction in reflection in the visible field achieved with these coatings was 3.5% and 4.0%, respectively. The adhesion of the coating to both substrates was good. The moth eye coating on PMMA demonstrated good performance in three prototypical accelerated ageing tests. The pencil hardness of the moth eye coatings on both substrates was <4B, which is less than required for most applications and needs further optimization. Additionally, we developed a roll-to-roll UV NIL pilot scale process and produced moth eye coatings on polyethylene terephthalate (PET) at line speeds up to two meters per minute. The resulting coatings showed a good replication of the moth eye structures and, consequently, a lowering in reflection of the coated PET of 3.0%. PMID:28788301

The use of drug-coated balloons in the treatment of femoropopliteal and infrapopliteal disease.

PubMed

Li, Jun; Karim, Adham; Shishehbor, Mehdi

2018-05-25

While the field of endovascular interventions has evolved in the last decade, technological advancements have rendered drug-coated balloons (DCBs) to be the first line therapy for femoropopliteal artery disease. As the knowledge continues to advance, the application of DCB to the infrapopliteal segments and its role in the setting of plaque modification atherectomy to minimize stent utilization will be further elucidated.

Broadband reflectance coatings for vacuum ultraviolet application

NASA Technical Reports Server (NTRS)

Herzig, Howard; Fleetwood, C. M., Jr.; Flint, B. K.

1987-01-01

An experimental investigation has obtained results indicating that neither LaF3 nor LiYF4 are acceptable alternatives to MgF2 as coatings for vacuum-deposited aluminum mirrors from which high UV reflectance down to 1150 A is required. Nevertheless, LaF3 may prove useful in those specialized applications in which the suppression of lower wavelength emissions, such as the 1216-A hydrogen line, is desirable.

Solder flow over fine line PWB surface finishes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hosking, F.M.; Hernandez, C.L.

1998-08-01

The rapid advancement of interconnect technology has stimulated the development of alternative printed wiring board (PWB) surface finishes to enhance the solderability of standard copper and solder-coated surfaces. These new finishes are based on either metallic or organic chemistries. As part of an ongoing solderability study, Sandia National Laboratories has investigated the solder flow behavior of two azole-based organic solderability preservations, immersion Au, immersion Ag, electroless Pd, and electroless Pd/Ni on fine line copper features. The coated substrates were solder tested in the as-fabricated and environmentally-stressed conditions. Samples were processed through an inerted reflow machine. The azole-based coatings generally providedmore » the most effective protection after aging. Thin Pd over Cu yielded the best wetting results of the metallic coatings, with complete dissolution of the Pd overcoat and wetting of the underlying Cu by the flowing solder. Limited wetting was measured on the thicker Pd and Pd over Ni finishes, which were not completely dissolved by the molten solder. The immersion Au and Ag finishes yielded the lowest wetted lengths, respectively. These general differences in solderability were directly attributed to the type of surface finish which the solder came in contact with. The effects of circuit geometry, surface finish, stressing, and solder processing conditions are discussed.« less

Study of sintering behavior of vapor forms of 1-octanethiol coated copper nanoparticles for application to ink-jet printing technology.

PubMed

Kwon, Jinhyeong; Park, Shinyoung; Haque, Md Mominul; Kim, Young-Seok; Lee, Caroline Sunyong

2012-04-01

Sub-50 nm copper nanoparticles coated with sub-5 nm 1-octanethiol layer for oxidation inhibition were examined to confirm the 1-octanethiol removal temperature as the sub-50 nm copper nanoparticles are sintered. As a result, 1-octanethiol Self-Assembled Multi-layers (SAMs) on sub-50 nm copper nanoparticles were successfully removed before sintering of copper nanoparticles so that a high density of copper line could be obtained. Finally, the line resistivity was measured and compared to verify the effect of sintering in different atmospheres. As a result, electrical resistivity of the copper pattern sintered in hydrogen atmosphere was measured at 6.96 x 10(-6) ohm-cm whereas that of the copper pattern sintered in mixed gas atmosphere was measured at 2.62 x 10(-5) ohm-cm. Thus, sintering of copper patterns was successfully done to show low electrical resistivity values. Moreover, removal of 1-octanethiol coating after sintering process was confirmed using X-ray photoelectron spectroscopy (XPS) analysis. By showing no sulfur content, XPS results indicate that 1-octanethiol is completely removed. Therefore, the vapor form of 1-octanethiol coating layers can be safely used as an oxidation inhibition layer for low temperature sintering processes and ink-jet applications.

Whey protein solution coating for fat-uptake reduction in deep-fried chicken breast strips.

PubMed

Dragich, Ann M; Krochta, John M

2010-01-01

This study investigated the use of whey protein, as an additional coating, in combination with basic, well-described predust, batter, and breading ingredients, for fat-uptake reduction in fried chicken. Chicken breasts were cut into strips (1 x 5 x 10 cm) and coated with wheat flour (WF) as a predust, dipped in batter, coated with WF as a breading, then dipped in 10% denatured whey protein isolate (DWPI) aqueous solution (wet basis). A WF-batter-WF treatment with no DWPI solution dip was included as a control. Coated chicken strips were deep-fried at 160 degrees C for 5 min. A Soxhlet-type extraction was performed to determine the fat content of the meat fraction of fried samples, the coating fraction of fried samples, raw chicken, and raw coating ingredients. The WF-batter-WF-10% DWPI solution had significantly lower fat uptake than the WF-batter-WF control, by 30.67% (dry basis). This article describes applied research involving fat reduction in coated deep-fried chicken. The methods used in this article were intended to achieve maximized fat reduction while maintaining a simple procedure applicable to actual food processing lines.

Effect of the deposition temperature on corrosion resistance and biocompatibility of the hydroxyapatite coatings

NASA Astrophysics Data System (ADS)

Vladescu, A.; Braic, M.; Azem, F. Ak; Titorencu, I.; Braic, V.; Pruna, V.; Kiss, A.; Parau, A. C.; Birlik, I.

2015-11-01

Hydroxyapatite (HAP) ceramics belong to a class of calcium phosphate-based materials, which have been widely used as coatings on titanium medical implants in order to improve bone fixation and thus to increase the lifetime of the implant. In this study, HAP coatings were deposited from pure HAP targets on Ti6Al4V substrates using the radio-frequency magnetron sputtering technique at substrate temperatures ranging from 400 to 800 °C. The surface morphology and the crystallographic structure of the films were investigated by atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The corrosion resistance of the coatings in saliva solution at 37 °C was evaluated by potentiodynamic polarization. Additionally, the human osteosarcoma cell line (MG-63) was used to test the biocompatibility of the coatings. The results showed that all of the coatings grown uniformly and that the increasing substrate temperature induced an increase in their crystallinity. Corrosion performance of the coatings was improved with the increase of the substrate temperature from 400 °C to 800 °C. Furthermore, all the coatings support the attachment and growth of the osteosarcoma cells with regard to the in vitro test findings.

The Tribological Performance of Surface Treated Ti6A14V as Sliding Against Si3N4 Ball and 316L Stainless Steel Cylinder

NASA Astrophysics Data System (ADS)

Kao, W. H.; Su, Y. L.; Horng, J. H.; Huang, H. C.

2016-12-01

Closed field unbalanced magnetron sputtering was used to deposit diamond-like carbon (Ti-C:H) coatings on Ti6Al4V alloy and gas nitrided Ti6Al4V alloy. Four different specimens were prepared, namely untreated Ti6Al4V alloy (Ti6Al4V), gas nitrided Ti6Al4V alloy (N-Ti6Al4V), Ti-C:H-coated Ti6Al4V alloy (Ti-C:H/Ti6Al4V) and Ti-C:H-coated gas nitrided Ti6Al4V alloy (Ti-C:H/N-Ti6Al4V). The tribological properties of the four specimens were evaluated using a reciprocating wear tester sliding against a Si3N4 ball (point contact mode) and 316L stainless steel cylinder (line contact mode). The wear tests were performed in a 0.89 wt.% NaCl solution. The results showed that the nitriding treatment increased the surface roughness and hardness of the Ti6Al4V alloy and improved the wear resistance as a result. In addition, the Ti-C:H coating also improved the tribological performance of Ti6Al4V. For example, compared to the untreated Ti6Al4V sample, the Ti-C:H coating reduced the wear depth and friction coefficient by 340 times and 10 times, respectively, in the point contact wear mode, and 151 times and 9 times, respectively, in the line contact wear mode. It is thus inferred that diamond-like carbon coatings are of significant benefit in extending the service life of artificial biomedical implants.

Sequence Alignment to Predict Across Species Susceptibility (SeqAPASS): A web-based tool for addressing the challenges of cross-species extrapolation of chemical toxicity

EPA Science Inventory

Conservation of a molecular target across species can be used as a line-of-evidence to predict the likelihood of chemical susceptibility. The web-based Sequence Alignment to Predict Across Species Susceptibility (SeqAPASS) tool was developed to simplify, streamline, and quantitat...

Global Conflicts On-line: Technoliteracy and Developing an Internet-Based Conflict Archive.

ERIC Educational Resources Information Center

Tuathail, Gearoid O; McCormack, Derek

1998-01-01

Reflects on the experience of teaching a large undergraduate course on the geography of global conflict. A World Wide Web site featuring an archive of conflicts around the globe was designed and integrated into the course. Discusses issues concerning the design and maintenance of the Web site and its usefulness as a learning resource. (MJP)

Facilitating Participation: From the EML Web Site to the Learning Network for Learning Design

ERIC Educational Resources Information Center

Hummel, Hans G. K.; Tattersall, Colin; Burgos, Daniel; Brouns, Francis; Kurvers, Hub; Koper, Rob

2005-01-01

This article investigates conditions for increasing active participation in on-line communities. As a case study, we use three generations of facilities designed to promote learning in the area of Educational Modelling Languages. Following a description of early experience with a conventional web site and with a community site offering facilities…

Evaluating CSL/CFL Website Usability: A User-Centered Design Approach

ERIC Educational Resources Information Center

Huang, Chung-Kai; Hsin, Ching-O; Chiu, Chiung-Hui

2010-01-01

With the widespread availability of Internet and computer technology, on-line web-based learning has become prevalent in the field of teaching Chinese as a second/foreign language (CSL/CFL). This study examined the concepts of usability and types of design elements that help construct an effective web-based learning environment, as well as their…

Efficacy of a Web-Based, Tailored, Alcohol Prevention/Intervention Program for College Students: 3-Month Follow-Up

ERIC Educational Resources Information Center

Bingham, C. Raymond; Barretto, Andrea Ippel; Walton, Maureen A.; Bryant, Christopher M.; Shope, Jean T.; Raghunathan, Trivellore E.

2011-01-01

This study presents the results of an efficacy evaluation of a web-based brief motivational alcohol prevention/intervention program called "Michigan Prevention and Alcohol Safety for Students" (M-PASS). Four on-line sessions providing individually-tailored feedback were delivered to first-year college students over 9 weeks. Non- and…

Critical loads and levels: Leveraging existing monitoring data

Treesearch

D. G. Fox; A. R. Riebau; R. Fisher

2006-01-01

A snapshot of current air quality in the National Parks and Wilderness areas of the US is presented based on data from the 165 site Interagency Monitoring of Protected Visual Environments, or IMPROVE program, and other relevant air quality monitoring programs. This snapshot is provided using the VIEWS web service, an on-line web-based data warehouse, analysis, and...

Publishing on the WWW. Part 5 - A brief history of the Internet and the World Wide Web

PubMed Central

Grech, V

2001-01-01

This article focuses on the history of the Internet and the World Wide Web, the media that in recent years have created the concept of objects existing ‘on-line’ in a virtual computer environment. These objects naturally include on-line journals such as Images in Paediatric Cardiology. PMID:22368602

High-Reflectivity Coatings for a Vacuum Ultraviolet Spectropolarimeter

NASA Astrophysics Data System (ADS)

Narukage, Noriyuki; Kubo, Masahito; Ishikawa, Ryohko; Ishikawa, Shin-nosuke; Katsukawa, Yukio; Kobiki, Toshihiko; Giono, Gabriel; Kano, Ryouhei; Bando, Takamasa; Tsuneta, Saku; Auchère, Frédéric; Kobayashi, Ken; Winebarger, Amy; McCandless, Jim; Chen, Jianrong; Choi, Joanne

2017-03-01

Precise polarization measurements in the vacuum ultraviolet (VUV) region are expected to be a new tool for inferring the magnetic fields in the upper atmosphere of the Sun. High-reflectivity coatings are key elements to achieving high-throughput optics for precise polarization measurements. We fabricated three types of high-reflectivity coatings for a solar spectropolarimeter in the hydrogen Lyman-α (Lyα; 121.567 nm) region and evaluated their performance. The first high-reflectivity mirror coating offers a reflectivity of more than 80 % in Lyα optics. The second is a reflective narrow-band filter coating that has a peak reflectivity of 57 % in Lyα, whereas its reflectivity in the visible light range is lower than 1/10 of the peak reflectivity (˜ 5 % on average). This coating can be used to easily realize a visible light rejection system, which is indispensable for a solar telescope, while maintaining high throughput in the Lyα line. The third is a high-efficiency reflective polarizing coating that almost exclusively reflects an s-polarized beam at its Brewster angle of 68° with a reflectivity of 55 %. This coating achieves both high polarizing power and high throughput. These coatings contributed to the high-throughput solar VUV spectropolarimeter called the Chromospheric Lyman-Alpha SpectroPolarimeter (CLASP), which was launched on 3 September, 2015.

Silver/hydroxyapatite composite coatings on porous titanium surfaces by sol-gel method.

PubMed

Qu, Jie; Lu, Xiong; Li, Dan; Ding, Yonghui; Leng, Yang; Weng, Jie; Qu, Shuxin; Feng, Bo; Watari, Fumio

2011-04-01

Hydroxyapatite (HA) coatings loaded with nanosilver particles is an attractive method to impart the HA coating with antibacterial properties. Producing Ag/HA coatings on porous Ti substrates have been an arduous job since commonly used line-of-sight techniques are not able to deposit uniform coatings on the inner pore surfaces of the porous Ti. In this study, porous Ti scaffolds with high porosity and interconnected structures were prepared by polymer impregnating method. A sol-gel process was used to produce uniform Ag/HA composite coatings on the surfaces of porous Ti substrates. Ca(NO(3) )(2) ·4H(2) O and P(2) O(5) in an ethyl alcohol based system was selected to prepare the sol, which ensured the homogeneous distribution of Ag in the sol. The characterization revealed that silver particles uniformly distributed in the coatings without agglomeration. High antibacterial ratio (>95%), against E. coli and S. albus was expressed by the silver-containing coatings (Ag/HA 0.8 and 1.6 wt %). The biocompatibility of the Ag/HA 0.8 surfaces was as good as that of pure HA surface, as revealed by culturing osteoblasts on them. The results indicated that Ag/HA 0.8 had the good balance between the biocompatibility and antibacterial properties of the coatings. Copyright © 2011 Wiley Periodicals, Inc.

Characterization and Properties of Micro-arc Composite Ceramic Coatings on Magnesium Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Long; Jiang, Bailing; Ge, Yanfeng

2013-05-21

Magnesium alloys are of growing interest for many industrial applications due to their favorable strength-to-weight ratio and excellent cast ability. However, one of the limiting factors in the use of magnesium on production vehicles is its poor corrosion resistance. Micro-arc Composite Ceramic (MCC) coatings on AZ91D magnesium alloys were prepared in combination with Micro-arc Oxidation (MAO) and electrophoresis technologies. The microstructure, corrosion resistance, abrasion resistance, stone impact resistance, thermal shock resistance and adhesion of MCC coating were studied, respectively. The surface and cross-section morphologies of MAO and MCC coating showed that the outer organic coating filled the holes on themore » surface of the MAO coating. It acted as a shelter on the MAO coating surface when the MCC coatings were exposed to corrosive environments. The corrosion resistance of the MCC coating was characterized by a copper-accelerated acetic acid salt spray test. The testing results showed that the creep back from scribe lines was less than 1mm and completely fit the evaluation standard. The composite structure of the MCC coating vastly improved the corrosion resistance of Mg alloys. According to testing standards, the resistance to abrasion, stone impact resistance, thermal shock resistance and adhesion of MCC coatings completely met the evaluation standard requirements. The MCC coated AZ91D magnesium alloys possessed excellent properties; this is a promising corrosion and wear resistance surface treatment technology on magnesium alloys for production vehicles.« less

Turbine airfoil to shroud attachment method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, Christian X; Kulkarni, Anand A; James, Allister W

2014-12-23

Bi-casting a platform (50) onto an end portion (42) of a turbine airfoil (31) after forming a coating of a fugitive material (56) on the end portion. After bi-casting the platform, the coating is dissolved and removed to relieve differential thermal shrinkage stress between the airfoil and platform. The thickness of the coating is varied around the end portion in proportion to varying amounts of local differential process shrinkage. The coating may be sprayed (76A, 76B) onto the end portion in opposite directions parallel to a chord line (41) of the airfoil or parallel to a mid-platform length (80) ofmore » the platform to form respective layers tapering in thickness from the leading (32) and trailing (34) edges along the suction side (36) of the airfoil.« less

Discrete nanoparticles induce loss of Legionella pneumophila biofilms from surfaces.

PubMed

Raftery, Tara D; Kerscher, Petra; Hart, Ashley E; Saville, Steven L; Qi, Bin; Kitchens, Christopher L; Mefford, Olin Thompson; McNealy, Tamara L

2014-08-01

Nanoparticles (NPs) have been shown to induce dispersal events in microbial biofilms but the mechanism of the dispersal is unknown. Biofilms contaminate many man-made aquatic systems such as cooling towers, spas and dental lines. Within these biofilms, Legionella pneumophila is a primary pathogen, leading to these environments serving as sources for disease outbreaks. Here we show a reduction in biofilm bio-volume upon treatment with citrate-coated 6-nm platinum NPs, polyethylene glycol (PEG)-coated 11-nm gold NPs, and PEG-coated 8-nm iron oxide NPs. Treatment with citrate-coated 8-nm silver NPs, however, did not reduce biomass. The synthesis of NPs that remain dispersed and resist irreversible aggregation in the exposure media appears to be a key factor in the ability of NPs to induce biofilm dispersal.

46 CFR 160.038-3 - Materials, workmanship, and construction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of the metal chest and fittings shall be given a heavy coat of quick drying red lead, zinc chromate... be constructed of metal and lined with wood. (b) The lining shall be so fitted and finished as to... explosives or pyrotechnics from contact with metal surfaces. (c) The metal shall be 1/8 inch thick and free...

46 CFR 160.038-3 - Materials, workmanship, and construction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of the metal chest and fittings shall be given a heavy coat of quick drying red lead, zinc chromate... be constructed of metal and lined with wood. (b) The lining shall be so fitted and finished as to... explosives or pyrotechnics from contact with metal surfaces. (c) The metal shall be 1/8 inch thick and free...

46 CFR 160.038-3 - Materials, workmanship, and construction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of the metal chest and fittings shall be given a heavy coat of quick drying red lead, zinc chromate... be constructed of metal and lined with wood. (b) The lining shall be so fitted and finished as to... explosives or pyrotechnics from contact with metal surfaces. (c) The metal shall be 1/8 inch thick and free...

46 CFR 160.038-3 - Materials, workmanship, and construction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of the metal chest and fittings shall be given a heavy coat of quick drying red lead, zinc chromate... be constructed of metal and lined with wood. (b) The lining shall be so fitted and finished as to... explosives or pyrotechnics from contact with metal surfaces. (c) The metal shall be 1/8 inch thick and free...

46 CFR 160.038-3 - Materials, workmanship, and construction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of the metal chest and fittings shall be given a heavy coat of quick drying red lead, zinc chromate... be constructed of metal and lined with wood. (b) The lining shall be so fitted and finished as to... explosives or pyrotechnics from contact with metal surfaces. (c) The metal shall be 1/8 inch thick and free...

Peak Lead Levels and Diagnostics in Lead Service Lines Dominated by PbO2 - abstract

EPA Science Inventory

Multiple studies have presented “profiles” of water lead levels from tap to main through lead service lines (LSLs), in systems where the LSLs were coated with common Pb(II) corrosion solids. These Pb(II) solids were either actual Pb(II) minerals or Pb(II) sorbed onto other pipe ...

Removing the Veil: Coates, Neoliberalism, and the Color Line

ERIC Educational Resources Information Center

Humphrey, David

2017-01-01

The words of W. E. B. Du Bois, in his widely-acclaimed work" The Souls of Black Folk," that "the problem of the twentieth century is the problem of the color-line" were a visceral attempt to illuminate the plight of the "Negro" in the United States of America. With this phrase, Du Bois positioned racial valorizations…

Calendar Instruments in Retrospective Web Surveys

ERIC Educational Resources Information Center

Glasner, Tina; van der Vaart, Wander; Dijkstra, Wil

2015-01-01

Calendar instruments incorporate aided recall techniques such as temporal landmarks and visual time lines that aim to reduce response error in retrospective surveys. Those calendar instruments have been used extensively in off-line research (e.g., computer-aided telephone interviews, computer assisted personal interviewing, and paper and pen…

Calibrator device for the extrusion of cable coatings

NASA Astrophysics Data System (ADS)

Garbacz, Tomasz; Dulebová, Ľudmila; Spišák, Emil; Dulebová, Martina

2016-05-01

This paper presents selected results of theoretical and experimental research works on a new calibration device (calibrators) used to produce coatings of electric cables. The aim of this study is to present design solution calibration equipment and present a new calibration machine, which is an important element of the modernized technology extrusion lines for coating cables. As a result of the extrusion process of PVC modified with blowing agents, an extrudate in the form of an electrical cable was obtained. The conditions of the extrusion process were properly selected, which made it possible to obtain a product with solid external surface and cellular core.

An inexpensive and fast method for infiltration coating of complex geometry matrices for ISOL production target applications

NASA Astrophysics Data System (ADS)

Kawai, Y.; Alton, G. D.; Bilheux, J.-C.

2005-12-01

An inexpensive, fast, and close to universal infiltration coating technique has been developed for fabricating fast diffusion-release ISOL targets. Targets are fabricated by deposition of finely divided (∼1 μm) compound materials in a paint-slurry onto highly permeable, complex structure reticulated-vitreous-carbon-foam (RVCF) matrices, followed by thermal heat treatment. In this article, we describe the coating method and present information on the physical integrity, uniformity of deposition, and matrix adherence of SiC, HfC and UC2 targets, destined for on-line use as targets at the Holifield Radioactive Ion Beam Facility (HRIBF).

Performance characteristics of zinc-rich coatings applied to carbon steel

NASA Technical Reports Server (NTRS)

Paton, W. J.

1973-01-01

A program was conducted to evaluate the performance of topcoated and untopcoated zinc-rich coatings. Sacrificial coatings of this type are required for protecting carbon steel structures from the aggressive KSC sea coast environment. A total of 59 commercially available zinc-rich coatings and 47 topcoated materials were exposed for an 18-month period. Test panels were placed in special racks placed approximately 30.5 m (100 feet) above the high tide line at the KSC Corrosion Test Site. Laboratory tests to determine the temperature resistance, abrasion resistance, and adhesion of the untopcoated zinc-rich coatings were also performed. It has been concluded that: (1) The inorganic types of zinc-rich coatings are far superior to the organic types in the KSC environment. (2) Organic zinc-rich coatings applied at 0.1 - 0.15 mm (4-6 mils) film thickness provide better corrosion protection than when applied at the manufacturers' recommended nominal film thickness of .08 mm (3 mils). (3) Topcoats are not necessary, or even desirable, when used in conjunction with zinc-rich coatings in the KSC environment. (4) Some types of inorganic zinc-rich coatings require an extended outdoor weathering period in order to obtain adequate mechanical properties. and (5) A properly formulated inorganic zinc-rich coating is not affected by a 24-hour thermal exposure to 400 C (752 F).

A value-added exopolysaccharide as a coating agent for MRI nanoprobes

NASA Astrophysics Data System (ADS)

Palma, Susana I. C. J.; Rodrigues, Carlos A. V.; Carvalho, Alexandra; Morales, Maria Del Puerto; Freitas, Filomena; Fernandes, Alexandra R.; Cabral, Joaquim M. S.; Roque, Ana C. A.

2015-08-01

Fucopol, a fucose-containing exopolysaccharide (EPS) produced by the bacterium Enterobacter A47 DSM 23139 using glycerol as a carbon source, was employed as a new coating material for iron oxide magnetic nanoparticles (MNPs). The coated particles were assessed as nanoprobes for cell labeling by Magnetic Resonance Imaging (MRI). The MNPs were synthesized by a thermal decomposition method and transferred to an aqueous medium by a ligand-exchange reaction with meso-2,3-dimercaptosuccinic acid (DMSA). Covalent binding of EPS to DMSA-stabilized nanoparticles (MNP-DMSA) resulted in a hybrid magnetic-biopolymeric nanosystem (MNP-DMSA-EPS) with a hydrodynamic size of 170 nm, a negative surface charge under physiological conditions and transverse to longitudinal relaxivity ratio, r2/r1, of 148. In vitro studies with two human cell lines (colorectal carcinoma - HCT116 - and neural stem/progenitor cells - ReNcell VM) showed that EPS promotes internalization of nanoparticles in both cell lines. In vitro MRI cell phantoms showed a superior performance of MNP-DMSA-EPS in ReNcell VM, for which the iron dose-dependent MRI signal drop was obtained at relatively low iron concentrations (12-20 μg Fe per ml) and short incubation times. Furthermore, ReNcell VM multipotency was not affected by culture in the presence of MNP-DMSA or MNP-DMSA-EPS for 14 days. Our study suggests that Fucopol-coated MNPs represent useful cell labeling nanoprobes for MRI.Fucopol, a fucose-containing exopolysaccharide (EPS) produced by the bacterium Enterobacter A47 DSM 23139 using glycerol as a carbon source, was employed as a new coating material for iron oxide magnetic nanoparticles (MNPs). The coated particles were assessed as nanoprobes for cell labeling by Magnetic Resonance Imaging (MRI). The MNPs were synthesized by a thermal decomposition method and transferred to an aqueous medium by a ligand-exchange reaction with meso-2,3-dimercaptosuccinic acid (DMSA). Covalent binding of EPS to DMSA-stabilized nanoparticles (MNP-DMSA) resulted in a hybrid magnetic-biopolymeric nanosystem (MNP-DMSA-EPS) with a hydrodynamic size of 170 nm, a negative surface charge under physiological conditions and transverse to longitudinal relaxivity ratio, r2/r1, of 148. In vitro studies with two human cell lines (colorectal carcinoma - HCT116 - and neural stem/progenitor cells - ReNcell VM) showed that EPS promotes internalization of nanoparticles in both cell lines. In vitro MRI cell phantoms showed a superior performance of MNP-DMSA-EPS in ReNcell VM, for which the iron dose-dependent MRI signal drop was obtained at relatively low iron concentrations (12-20 μg Fe per ml) and short incubation times. Furthermore, ReNcell VM multipotency was not affected by culture in the presence of MNP-DMSA or MNP-DMSA-EPS for 14 days. Our study suggests that Fucopol-coated MNPs represent useful cell labeling nanoprobes for MRI. Electronic supplementary information (ESI) available: Fig. S1-S3. See DOI: 10.1039/c5nr01979f

Chemically Modified Bacteriophage as a Streamlined Approach to Noninvasive Breast Cancer Imaging

DTIC Science & Technology

2012-10-01

major MALDI peaks is 245 Da, which is presumably an aldol addition of the ketone group to the PLP aldehyde (expected change: 248 Da...modification of filamentous (fd) phage. N-terminal alanines (Ala) of the pVIII coat proteins lining the filamentous phage are converted to ketone ...the ∼4200 coat proteins into ketone groups. These sites can then serve as chemospecific handles for the attachment of alkoxyamine groups through

Lithographic performance of recent DUV photoresists

NASA Astrophysics Data System (ADS)

Streefkerk, Bob; van Ingen Schenau, Koen; Buijk, Corine

1998-06-01

Commercially available photoresists from the major photoresist vendors are investigated using a PAS 5500/300 wafer stepper, a 31.1 mm diameter field size high throughput wafer stepper with variable NA capability up to 0.63. The critical dimension (CD) investigated is 0.25 micrometers and lower for dense and isolated lines and 0.25 micrometers for dense contact holes. The photoresist process performance is quantified by measuring exposure-defocus windows for a specific resolution using a CD SEM. Photoresists that are comparable with or better than APEX-E with RTC top coat, which is the current base line process for lines and spaces imaging performance, are Clariant AZ-DX1300 and Shin Etsu SEPR-4103PB50. Most recent photoresists have much improved delay performance when compared to APEX without top coat. Improvement, when an organic BARC is applied, depends on the actual photoresist characteristics. The optimal photoresist found for 0.25 micrometers contact holes is TOK DP015 C. This process operates at optimal conditions.

Real-time imaging, spectroscopy, and structural investigation of cathodic plasma electrolytic oxidation of molybdenum

NASA Astrophysics Data System (ADS)

Stojadinović, Stevan; Tadić, Nenad; Šišović, Nikola M.; Vasilić, Rastko

2015-06-01

In this paper, the results of the investigation of cathodic plasma electrolytic oxidation (CPEO) of molybdenum at 160 V in a mixed solution of borax, water, and ethylene glycol are presented. Real-time imaging and optical emission spectroscopy were used for the characterization of the CPEO. During the process, vapor envelope is formed around the cathode and strong electric field within the envelope caused the generation of plasma discharges. The spectral line shape analysis of hydrogen Balmer line Hβ (486.13 nm) shows that plasma discharges are characterized by the electron number density of about 1.4 × 1021 m-3. The electron temperature of 15 000 K was estimated by measuring molybdenum atomic lines intensity. Surface morphology, chemical, and phase composition of coatings formed by CPEO were characterized by scanning electron microscopy with energy dispersive x-ray spectroscopy and x-ray diffraction. The elemental components of CPEO coatings are Mo and O and the predominant crystalline form is MoO3.

REAP (raster e-beam advanced process) using 50-kV raster e-beam system for sub-100-nm node mask technology

NASA Astrophysics Data System (ADS)

Baik, Ki-Ho; Dean, Robert L.; Mueller, Mark; Lu, Maiying; Lem, Homer Y.; Osborne, Stephen; Abboud, Frank E.

2002-07-01

A chemically amplified resist (CAR) process has been recognized as an approach to meet the demanding critical dimension (CD) specifications of 100nm node technology and beyond. Recently, significant effort has been devoted to optimizing CAR materials, which offer the characteristics required for next generation photomask fabrication. In this paper, a process established with a positive-tone CAR from TOK and 50kV MEBES eXara system is discussed. This resist is developed for raster scan 50 kV e-beam systems. It has high contrast, good coating characteristics, good dry etch selectivity, and high environmental stability. The coating process is conducted in an environment with amine concentration less than 2 ppb. A nitrogen environment is provided during plate transfer steps. Resolution using a 60nm writing grid is 90nm line and space patterns. CD linearity is maintained down to 240nm for isolated lines or spaces by applying embedded proximity effect correction (emPEC). Optimizations of post-apply bake (PAB) and post-expose bake (PEB) time, temperature, and uniformity are completed to improve adhesion, coating uniformity, and resolution. A puddle develop process is optimized to improve line edge roughness, edge slope, and resolution. Dry etch process is optimized on a TetraT system to transfer the resist image into the chrome layer with minimum etch bias.

Modified M20 Beam Position Monitor Testing

NASA Astrophysics Data System (ADS)

Koros, Jessica; Musson, John

2017-09-01

Beam position monitors (BPMs) are used to measure lateral beam position. Two pairs of modified wire BPMs are being evaluated for installation into the injector at Jefferson Lab (JLab). The BPMs were coated with a Non-Evaporable Getter (NEG) to aid in pumping at the electron gun, as an ultra-high vacuum is required to protect the gun and to avoid scattering the beam. Beam in the injector has a large diameter, allowing extraction of second moments to give information about beam profile and emittance. The purpose of this project is to determine the effects of NEG coating on the BPMs and to calculate second moments from beam models on the Goubau Line (G-Line). Using the G-Line, scans of the BPMs were taken before and after NEG coating. Each scan produced an electrical field map, which characterizes properties of the BPM, including scale factors and coupling. Second moments were calculated using superposition of previous scan data, and verification of this method was attempted using several beam models. Results show the BPMs responded well to NEG and that measurement of second moments is possible. Once the BPMs are installed, they will enhance gun vacuum and enable monitoring of shape and trajectory of the beam as it exits the electron gun to ensure quality beam for experiments. This work is made possible through support from NSF award 1659177 to Old Dominion University.

Effectiveness of Vaporous Hydrogen Peroxide for the Decontamination of Representative Military Materials

DTIC Science & Technology

2004-11-16

Agent Resistant Coating (CARC) Geobacillus stearothermophilus ATCC 7953 Flott Glass Galvanized aluminum Polyimid (Kapton) Nylon Webbing Runway...spores were harvested from 7-10 day –old cultures plated upon Lemko Agar. The spores were washed thrice in sterile distilled water (dH2O), and...NEGATIVE SURROGATE Inocula of log-phase Y. ruckeri were prepared immediately before application to sterile coupons. Cells were grown in nutrient

Discovering Central Practitioners in a Medical Discussion Forum Using Semantic Web Analytics.

PubMed

Rajabi, Enayat; Abidi, Syed Sibte Raza

2017-01-01

The aim of this paper is to investigate semantic web based methods to enrich and transform a medical discussion forum in order to perform semantics-driven social network analysis. We use the centrality measures as well as semantic similarity metrics to identify the most influential practitioners within a discussion forum. The centrality results of our approach are in line with centrality measures produced by traditional SNA methods, thus validating the applicability of semantic web based methods for SNA, particularly for analyzing social networks for specialized discussion forums.

Web-Based Media Contents Editor for UCC Websites

NASA Astrophysics Data System (ADS)

Kim, Seoksoo

The purpose of this research is to "design web-based media contents editor for establishing UCC(User Created Contents)-based websites." The web-based editor features user-oriented interfaces and increased convenience, significantly different from previous off-line editors. It allows users to edit media contents online and can be effectively used for online promotion activities of enterprises and organizations. In addition to development of the editor, the research aims to support the entry of enterprises and public agencies to the online market by combining the technology with various UCC items.

Evidence from Multiple Species that Spider Silk Glue Component ASG2 is a Spidroin

PubMed Central

Collin, Matthew A.; Clarke, Thomas H.; Ayoub, Nadia A.; Hayashi, Cheryl Y.

2016-01-01

Spiders in the superfamily Araneoidea produce viscous glue from aggregate silk glands. Aggregate glue coats prey-capture threads and hampers the escape of prey from webs, thereby increasing the foraging success of spiders. cDNAs for Aggregate Spider Glue 1 (ASG1) and 2 (ASG2) have been previously described from the golden orb-weaver, Nephila clavipes, and Western black widow, Latrodectus hesperus. To further investigate aggregate glues, we assembled ASG1 and ASG2 from genomic target capture libraries constructed from three species of cob-web weavers and three species of orb-web weavers, all araneoids. We show that ASG1 is unlikely to be a glue, but rather is part of a widespread arthropod gene family, the peritrophic matrix proteins. For ASG2, we demonstrate its remarkable architectural and sequence similarities to spider silk fibroins, indicating that ASG2 is a member of the spidroin gene family. Thus, spidroins have diversified into glues in addition to task-specific, high performance fibers. PMID:26875681

A Module Experimental Process System Development Unit (MEPSDU)

NASA Technical Reports Server (NTRS)

1981-01-01

Design work for a photovoltaic module, fabricated using single crystal silicon dendritic web sheet material, resulted in the identification of surface treatment to the module glass superstrate which improved module efficiencies. A final solar module environmental test, a simulated hailstone impact test, was conducted on full size module superstrates to verify that the module's tempered glass superstrate can withstand specified hailstone impacts near the corners and edges of the module. Process sequence design work on the metallization process selective, liquid dopant investigation, dry processing, and antireflective/photoresist application technique tasks, and optimum thickness for Ti/Pd are discussed. A noncontact cleaning method for raw web cleaning was identified and antireflective and photoresist coatings for the dendritic webs were selected. The design of a cell string conveyor, an interconnect feed system, rolling ultrasonic spot bonding heat, and the identification of the optimal commercially available programmable control system are also discussed. An economic analysis to assess cost goals of the process sequence is also given.

Reductions in employee productivity impairment observed after implementation of web-based worksite health promotion programs.

PubMed

Silberman, Jordan; Schwartz, Steven; Giuseffi, Danielle L; Wang, Chun; Nevedal, Dana; Bedrosian, Richard

2011-12-01

To assess changes in employee productivity impairment observed after the implementation of several Web-based health promotion programs. Health risk assessments and self-report measures of productivity impairment were administered on-line to more than 43,000 participants of Web-based health promotion programs. Reductions in productivity impairment were observed after 1 month of program utilization. Productivity impairment at 90- and 180-day follow-ups also decreased relative to baseline. Improvements in employee health were associated with reductions in employee productivity impairment. The use of Web-based health promotion programs was associated with reductions in productivity impairment and improvements in employee health. After the implementation of Web-based health promotion programs, reductions in productivity impairment may be observed before reductions in direct health care costs.

Comparing Modes of Delivery: Classroom and On-Line (and Other) Learning.

ERIC Educational Resources Information Center

deLeon, Linda; Killian, Jerri

2000-01-01

Moving beyond question of whether on-line education is beneficial or harmful, explores conditions under which one or another of six instructional methods lecture, collaborative learning, experiential learning, learning contracts, televised courses, and Web-based learning work best. Finds specific methods more appropriate for some subject matters,…

75 FR 71376 - Simplified Network Application Processing System, On-Line Registration and Account Maintenance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-23

...-02] RIN 0694-AE98 Simplified Network Application Processing System, On-Line Registration and Account...'') electronically via BIS's Simplified Network Application Processing (SNAP-R) system. Currently, parties must... Network Applications Processing System (SNAP-R) in October 2006. The SNAP-R system provides a Web based...

The open research system: a web-based metadata and data repository for collaborative research

Treesearch

Charles M. Schweik; Alexander Stepanov; J. Morgan Grove

2005-01-01

Beginning in 1999, a web-based metadata and data repository we call the "open research system" (ORS) was designed and built to assist geographically distributed scientific research teams. The purpose of this innovation was to promote the open sharing of data within and across organizational lines and across geographic distances. As the use of the system...

75 FR 19455 - Intent To Prepare an Environmental Impact Statement for the South Bay Metro Green Line Extension...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

... Corridor. LACMTA operates the Metro transit system in Los Angeles County. The proposed project would..., 2009 and available on the LACMTA Web site ( http://www.metro.net/southbayextension ). Pursuant to 23... Analysis will be available at the meetings and are available on the LACMTA Web site ( http://www.metro.net...

Recommender System and Web 2.0 Tools to Enhance a Blended Learning Model

ERIC Educational Resources Information Center

Hoic-Bozic, Natasa; Dlab, Martina Holenko; Mornar, Vedran

2016-01-01

Blended learning models that combine face-to-face and online learning are of great importance in modern higher education. However, their development should be in line with the recent changes in e-learning that emphasize a student-centered approach and use tools available on the Web to support the learning process. This paper presents research on…

OWL (On-Lie Webstories for Learning): A Unique Web-based Literacy Resource for Primary/Elementary Children.

ERIC Educational Resources Information Center

Juliebo, Moira; Durnford, Carol

2000-01-01

Describes Online Webstories for Learning (OWL), a Web-based resource for elementary school literacy education that was initially developed for use in the United Kingdom. Discusses the importance of including narrative, how OWL is being adapted for use in other countries, and off-line class activities suggested as part of OWL. (Contains 8…

Assessing I-Grid(TM) web-based monitoring for power quality and reliability benchmarking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Divan, Deepak; Brumsickle, William; Eto, Joseph

2003-04-30

This paper presents preliminary findings from DOEs pilot program. The results show how a web-based monitoring system can form the basis for aggregation of data and correlation and benchmarking across broad geographical lines. A longer report describes additional findings from the pilot, including impacts of power quality and reliability on customers operations [Divan, Brumsickle, Eto 2003].

75 FR 11988 - Notice of Request for Approval To Collect New Information: Collection of Safety Culture Data

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-12

... comments using the Internet, you may use the Web site http://www.regulations.gov . Please follow the instructions for submitting an electronic comment. You can also review comments on-line at the same Web site... consequences (e.g., a train in dark territory proceeds beyond its authority); (3) events that are below the FRA...

78 FR 4843 - Hydro Development; Notice of Preliminary Permit Application Accepted for Filing and Soliciting...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-23

...-foot-wide, 98-foot-deep concrete lined vertical shaft containing 10-foot-diameter siphon piping and a... via the Internet. See 18 CFR Sec. 385.2001(a)(1)(iii) and the instructions on the Commission's Web... Commission's Web site at http://www.ferc.gov/docs-filing/elibrary.asp . Enter the docket number (P-14360) in...

Development of Web Interfaces for Analysis Codes

NASA Astrophysics Data System (ADS)

Emoto, M.; Watanabe, T.; Funaba, H.; Murakami, S.; Nagayama, Y.; Kawahata, K.

Several codes have been developed to analyze plasma physics. However, most of them are developed to run on supercomputers. Therefore, users who typically use personal computers (PCs) find it difficult to use these codes. In order to facilitate the widespread use of these codes, a user-friendly interface is required. The authors propose Web interfaces for these codes. To demonstrate the usefulness of this approach, the authors developed Web interfaces for two analysis codes. One of them is for FIT developed by Murakami. This code is used to analyze the NBI heat deposition, etc. Because it requires electron density profiles, electron temperatures, and ion temperatures as polynomial expressions, those unfamiliar with the experiments find it difficult to use this code, especially visitors from other institutes. The second one is for visualizing the lines of force in the LHD (large helical device) developed by Watanabe. This code is used to analyze the interference caused by the lines of force resulting from the various structures installed in the vacuum vessel of the LHD. This code runs on PCs; however, it requires that the necessary parameters be edited manually. Using these Web interfaces, users can execute these codes interactively.

Evaluation of physical activity web sites for use of behavior change theories.

PubMed

Doshi, Amol; Patrick, Kevin; Sallis, James F; Calfas, Karen

2003-01-01

Physical activity (PA) Web sites were assessed for their use of behavior change theories, including constructs of the health belief model, Transtheoretical Model, social cognitive theory, and the theory of reasoned action and planned behavior. An evaluation template for assessing PA Web sites was developed, and content validity and interrater reliability were demonstrated. Two independent raters evaluated 24 PA Web sites. Web sites varied widely in application of theory-based constructs, ranging from 5 to 48 on a 100-point scale. The most common intervention strategies were general information, social support, and realistic goal areas. Coverage of theory-based strategies was low, varying from 26% for social cognitive theory to 39% for health belief model. Overall, PA Web sites provided little assessment, feedback, or individually tailored assistance for users. They were unable to substantially tailor the on-line experience for users at different stages of change or different demographic characteristics.

Comparison of sorafenib-loaded poly (lactic/glycolic) acid and DPPC liposome nanoparticles in the in vitro treatment of renal cell carcinoma.

PubMed

Liu, James; Boonkaew, Benjawan; Arora, Jaspreet; Mandava, Sree Harsha; Maddox, Michael M; Chava, Srinivas; Callaghan, Cameron; He, Jibao; Dash, Srikanta; John, Vijay T; Lee, Benjamin R

2015-03-01

The objective of this study is to develop and compare several Sorafenib-loaded biocompatible nanoparticle models in order to optimize drug delivery and tumor cellular kill thereby improving the quality of Sorafenib-regimented chemotherapy. Sorafenib-loaded poly (lactic-co-glycolic) acid (PLGA), 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) liposomes, and hydrophobically modified chitosan (HMC)-coated DPPC liposomes were evaluated for several characteristics including zeta potential, drug loading, and release profile. Cytotoxicity and uptake trials were also studied using cell line RCC 786-0, a human metastatic clear cell histology renal cell carcinoma cell line. Sorafenib-loaded PLGA particles and HMC-coated DPPC liposomes exhibited significantly improved cell kill compared to Sorafenib alone at lower concentrations, namely 10-15 and 5-15 μM from 24 to 96 h, respectively. At maximum dosage and time (15 μM and 96 h), Sorafenib-loaded PLGA and HMC-coated liposomes killed 88.3 ± 1.8% and 98 ± 1.1% of all tumor cells, significant values compared with Sorafenib 81.8 ± 1.7% (p < 0.01). Likewise, HMC coating substantially improved cell kill for liposome model for all concentrations (5-15 μM) and at time points (24-96 h) (p < 0.01). PLGA and HMC-coated liposomes are promising platforms for drug delivery of Sorafenib. Because of different particle characteristics of PLGA and liposomes, each model can be further developed for unique clinical modalities. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Fabrication and characterization of copper oxide (CuO)–gold (Au)–titania (TiO{sub 2}) and copper oxide (CuO)–gold (Au)–indium tin oxide (ITO) nanowire heterostructures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chopra, Nitin, E-mail: nchopra@eng.ua.edu; Department of Biological Sciences, The University of Alabama, Tuscaloosa, AL 35487; Shi, Wenwu

2014-10-15

Nanoscale heterostructures composed of standing copper oxide nanowires decorated with Au nanoparticles and shells of titania and indium tin oxide were fabricated. The fabrication process involved surfactant-free and wet-chemical nucleation of gold nanoparticles on copper oxide nanowires followed by a line-of-sight sputtering of titania or indium tin oxide. The heterostructures were characterized using high resolution electron microscopy, diffraction, and energy dispersive spectroscopy. The interfaces, morphologies, crystallinity, phases, and chemical compositions were analyzed. The process of direct nucleation of gold nanoparticles on copper oxide nanoparticles resulted in low energy interface with aligned lattice for both the components. Coatings of polycrystalline titaniamore » or amorphous indium tin oxide were deposited on standing copper oxide nanowire–gold nanoparticle heterostructures. Self-shadowing effect due to standing nanowire heterostructures was observed for line-of-sight sputter deposition of titania or indium tin oxide coatings. Finally, the heterostructures were studied using Raman spectroscopy and ultraviolet–visible spectroscopy, including band gap energy analysis. Tailing in the band gap energy at longer wavelengths (or lower energies) was observed for the nanowire heterostructures. - Highlights: • Heterostructures comprised of CuO nanowires coated with Au nanoparticles. • Au nanoparticles exhibited nearly flat and low energy interface with nanowire. • Heterostructures were further sputter-coated with oxide shell of TiO{sub 2} or ITO. • The process resulted in coating of polycrystalline TiO{sub 2} and amorphous ITO shell.« less

On-line coating of glass with tin oxide by atmospheric pressure chemical vapor deposition.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, Mark D.; Sopko, J.F.; Houf, William G.

2006-11-01

Atmospheric pressure chemical vapor deposition (APCVD) of tin oxide is a very important manufacturing technique used in the production of low-emissivity glass. It is also the primary method used to provide wear-resistant coatings on glass containers. The complexity of these systems, which involve chemical reactions in both the gas phase and on the deposition surface, as well as complex fluid dynamics, makes process optimization and design of new coating reactors a very difficult task. In 2001 the U.S. Dept. of Energy Industrial Technologies Program Glass Industry of the Future Team funded a project to address the need for more accuratemore » data concerning the tin oxide APCVD process. This report presents a case study of on-line APCVD using organometallic precursors, which are the primary reactants used in industrial coating processes. Research staff at Sandia National Laboratories in Livermore, CA, and the PPG Industries Glass Technology Center in Pittsburgh, PA collaborated to produce this work. In this report, we describe a detailed investigation of the factors controlling the growth of tin oxide films. The report begins with a discussion of the basic elements of the deposition chemistry, including gas-phase thermochemistry of tin species and mechanisms of chemical reactions involved in the decomposition of tin precursors. These results provide the basis for experimental investigations in which tin oxide growth rates were measured as a function of all major process variables. The experiments focused on growth from monobutyltintrichloride (MBTC) since this is one of the two primary precursors used industrially. There are almost no reliable growth-rate data available for this precursor. Robust models describing the growth rate as a function of these variables are derived from modeling of these data. Finally, the results are used to conduct computational fluid dynamic simulations of both pilot- and full-scale coating reactors. As a result, general conclusions are reached concerning the factors affecting the growth rate in on-line APCVD reactors. In addition, a substantial body of data was generated that can be used to model many different industrial tin oxide coating processes. These data include the most extensive compilation of thermochemistry for gas-phase tin-containing species as well as kinetic expressions describing tin oxide growth rates over a wide range of temperatures, pressures, and reactant concentrations.« less

Finding, Browsing and Getting Data Easily Using SPDF Web Services

NASA Technical Reports Server (NTRS)

Candey, R.; Chimiak, R.; Harris, B.; Johnson, R.; Kovalick, T.; Lal, N.; Leckner, H.; Liu, M.; McGuire, R.; Papitashvili, N.;

Novel chitosan/diclofenac coatings on medical grade stainless steel for hip replacement applications

NASA Astrophysics Data System (ADS)

Finšgar, Matjaž; Uzunalić, Amra Perva; Stergar, Janja; Gradišnik, Lidija; Maver, Uroš

2016-05-01

Corrosion resistance, biocompatibility, improved osteointegration, as well the prevention of inflammation and pain are the most desired characteristics of hip replacement implants. In this study we introduce a novel multi-layered coating on AISI 316LVM stainless steel that shows promise with regard to all mentioned characteristics. The coating is prepared from alternating layers of the biocompatible polysaccharide chitosan and the non-steroid anti-inflammatory drug (NSAID), diclofenac. Electrochemical methods were employed to characterize the corrosion behavior of coated and uncoated samples in physiological solution. It is shown that these coatings improve corrosion resistance. It was also found that these coatings release the incorporated drug in controlled, multi-mechanism manner. Adding additional layers on top of the as-prepared samples, has potential for further tailoring of the release profile and increasing the drug dose. Biocompatibility was proven on human-derived osteoblasts in several experiments. Only viable cells were found on the sample surface after incubation of the samples with the same cell line. This novel coating could prove important for prolongation of the application potential of steel-based hip replacements, which are these days often replaced by more expensive ceramic or other metal alloys.

Novel chitosan/diclofenac coatings on medical grade stainless steel for hip replacement applications

PubMed Central

Finšgar, Matjaž; Uzunalić, Amra Perva; Stergar, Janja; Gradišnik, Lidija; Maver, Uroš

2016-01-01

Corrosion resistance, biocompatibility, improved osteointegration, as well the prevention of inflammation and pain are the most desired characteristics of hip replacement implants. In this study we introduce a novel multi-layered coating on AISI 316LVM stainless steel that shows promise with regard to all mentioned characteristics. The coating is prepared from alternating layers of the biocompatible polysaccharide chitosan and the non-steroid anti-inflammatory drug (NSAID), diclofenac. Electrochemical methods were employed to characterize the corrosion behavior of coated and uncoated samples in physiological solution. It is shown that these coatings improve corrosion resistance. It was also found that these coatings release the incorporated drug in controlled, multi-mechanism manner. Adding additional layers on top of the as-prepared samples, has potential for further tailoring of the release profile and increasing the drug dose. Biocompatibility was proven on human-derived osteoblasts in several experiments. Only viable cells were found on the sample surface after incubation of the samples with the same cell line. This novel coating could prove important for prolongation of the application potential of steel-based hip replacements, which are these days often replaced by more expensive ceramic or other metal alloys. PMID:27215333

Failure Mechanism of a Stellite Coating on Heat-Resistant Steel

NASA Astrophysics Data System (ADS)

Wang, Dong; Zhao, Haixing; Wang, Huang; Li, Yuyan; Liu, Xia; He, Guo

2017-09-01

The Stellite 21 coating on the heat-resistant steel X12CrMoWVNbN10-1-1 (so-called COSTE) used in a steam turbine valve was found to be fatigue broken after service at around 873 K (600 °C) for about 8 years. In order to investigate the failure mechanism, a fresh Stellite 21 coating was also prepared on the same COSTE steel substrate by using the similar deposition parameters for comparison. It was found that the Stellite 21 coating was significantly diluted by the steel, resulting in a thin Fe-rich layer in the coating close to the fusion line. Such high Fe concentration together with the incessant Fe diffusion from the steel substrate to the coating during the service condition (about 873 K (600 °C) for long time) induced the eutectoid decomposition of the fcc α-Co(Fe,Cr,Mo) solid solution, forming an irregular eutectoid microstructure that was composed of the primitive cubic α'-FeCo(Cr,Mo) phase and the tetragonal σ-CrCo(Fe,Mo) phase. The brittle nature of such α'/ σ eutectoid microstructure contributed to the fatigue fracture of the Stellite 21 coating, resulting in an intergranular rupture mode.

In vitro metal ion release and biocompatibility of amorphous Mg67Zn28Ca5 alloy with/without gelatin coating.

PubMed

Chan, W Y; Chian, K S; Tan, M J

2013-12-01

Amorphous zinc-rich Mg-Zn-Ca alloys have exhibited good tissue compatibility and low hydrogen evolution in vivo. However, suboptimal cell-surface interaction on magnesium alloy surface observed in vitro could lead to reduced integration with host tissue for regenerative purpose. This study aims to improve cell-surface interaction of amorphous Mg67Zn28Ca5 alloy by coating a gelatin layer by electrospinning. Coated/uncoated alloys were immersed and extracted for 3 days under different CO2. The immersion results showed that pH and metal ion release in the alloy extracts were affected by gelatin coating and CO2, suggesting their roles in alloy biocorrosion and a mechanism has been proposed for the alloy-CO2 system with/without coating. Cytotoxicity results are evident that gelatin-coated alloy with 2-day crosslinking not only exhibited no indirect cytotoxicity, but also supported attachment of L929 and MG63 cell lines around/on the alloy with high viability. Therefore, amorphous Mg67Zn28Ca5 alloy coated with gelatin by electrospinning technique provides a useful method to improve alloy biocompatibility. © 2013 Elsevier B.V. All rights reserved.

Open Marketplace for Simulation Software on the Basis of a Web Platform

NASA Astrophysics Data System (ADS)

Kryukov, A. P.; Demichev, A. P.

2016-02-01

The focus in development of a new generation of middleware shifts from the global grid systems to building convenient and efficient web platforms for remote access to individual computing resources. Further line of their development, suggested in this work, is related not only with the quantitative increase in their number and with the expansion of scientific, engineering, and manufacturing areas in which they are used, but also with improved technology for remote deployment of application software on the resources interacting with the web platforms. Currently, the services for providers of application software in the context of scientific-oriented web platforms is not developed enough. The proposed in this work new web platforms of application software market should have all the features of the existing web platforms for submissions of jobs to remote resources plus the provision of specific web services for interaction on market principles between the providers and consumers of application packages. The suggested approach will be approved on the example of simulation applications in the field of nonlinear optics.

Biological influence of Ca/P ratio on calcium phosphate coatings by sol-gel processing.

PubMed

Catauro, M; Papale, F; Sapio, L; Naviglio, S

2016-08-01

The objective of this work has been to develop low temperature sol-gel glass coatings to modify the substrate surface and to evaluate their bioactivity and biocompatibility. Glasses, based on SiO2·CaO·P2O5, were synthesized by the sol-gel technique using tetraethyl orthosilicate, calcium nitrate tetrahydrate and triethyl phosphate as precursors of SiO2, CaO and P2O5, respectively. Those materials, still in the sol phase, have been used to coat substrates by means of the dip-coating technique. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) has been used for characterize coatings and a microstructural analysis has been obtained using scanning electron microscopy (SEM). The potential applications of the coatings in the biomedical field were evaluated by bioactivity and biocompatibility tests. The coated substrate was immersed in simulated body fluid (SBF) for 21days and the hydroxyapatite deposition on its surface was subsequently evaluated via SEM-EDXS analysis, as an index of bone-bonding capability. In order to study the cell behavior and response to our silica based materials, prepared via the sol-gel method, with various Ca/P ratio and coating substrate, we have used the human osteoblast-like U2OS cell line. Copyright © 2016 Elsevier B.V. All rights reserved.

Silicon-hydroxyapatite bioactive coatings (Si-HA) from diatomaceous earth and silica. Study of adhesion and proliferation of osteoblast-like cells.

PubMed

López-Alvarez, M; Solla, E L; González, P; Serra, J; León, B; Marques, A P; Reis, R L

2009-05-01

The aim of this study consisted on investigating the influence of silicon substituted hydroxyapatite (Si-HA) coatings over the human osteoblast-like cell line (SaOS-2) behaviour. Diatomaceous earth and silica, together with commercial hydroxyapatite were respectively the silicon and HA sources used to produce the Si-HA coatings. HA coatings with 0 wt% of silicon were used as control of the experiment. Pulsed laser deposition (PLD) was the selected technique to deposit the coatings. The Si-HA thin films were characterized by Fourier Transformed Infrared Spectroscopy (FTIR) demonstrating the efficient transfer of Si to the HA structure. The in vitro cell culture was established to assess the cell attachment, proliferation and osteoblastic activity respectively by, Scanning Electron Microscopy (SEM), DNA and alkaline phosphatase (ALP) quantification. The SEM analysis demonstrated a similar adhesion behaviour of the cells on the tested materials and the maintenance of the typical osteoblastic morphology along the time of culture. The Si-HA coatings did not evidence any type of cytotoxic behaviour when compared with HA coatings. Moreover, both the proliferation rate and osteoblastic activity results showed a slightly better performance on the Si-HA coatings from diatoms than on the Si-HA from silica.

Asbestos Workshop: Sampling, Analysis, and Risk Assessment

DTIC Science & Technology

2012-03-01

coatings Vinyl/asbestos floor tile Automatic transmission components Clutch facings Disc brake pads Drum brake linings Brake blocks Commercial and...A naturally-occurring pliant and fibrous mineral with heat-resistant properties • Serpentine Class: joint compound,‘popcorn’ceilings, brake pads...fabrics, and is used in fire-resistant and insulating materials such as brake linings. The asbestos minerals include chrysotile (white asbestos) and

Effect of Mn on the Formation of Oxide Buildups Upon HVOF-Sprayed MCrAlY-Ceramic-Type Cermet Coatings

NASA Astrophysics Data System (ADS)

Huang, Tsai-Shang

2011-03-01

Thermal spray coatings have been widely used on hearth rolls in a continuous annealing line to improve steel sheet quality and to prolong the roll service life. One of the common defects formed on a working hearth roll is the oxide buildup. HVOF-sprayed CoCrAlY-CrB2-Y2O3 coating was used in this study to duplicate buildups by reacting with Fe and Mn oxides. The reaction was performed in a furnace at 900 °C with inert gases flowing through. After reacting for 8 days, large Mn-rich buildups were formed on the coating while the buildups without Mn were very small. Mn was shown to enhance the formation of buildups. Buildups from a hearth roll were also examined and compared with the laboratory ones.