Testing and evaluation of a slot and tab construction technique for light-weight wood-fiber-based structural panels under bending

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2015-01-01

This paper presented construction and strain distributions for light-weight wood-fiber-based structural panels with tri-grid core made from phenolic impregnated laminated paper composites under bending. A new fastening configuration of slots in the faces and tabs on the core was applied to the face/core interfaces of the sandwich panel in addition to epoxy resin. Both...

Wood Bond Testing

NASA Technical Reports Server (NTRS)

1989-01-01

A joint development program between Hartford Steam Boiler Inspection Technologies and The Weyerhaeuser Company resulted in an internal bond analyzer (IBA), a device which combines ultrasonics with acoustic emission testing techniques. It is actually a spinoff from a spinoff, stemming from a NASA Lewis invented acousto-ultrasonic technique that became a system for testing bond strength of composite materials. Hartford's parent company, Acoustic Emission Technology Corporation (AET) refined and commercialized the technology. The IBA builds on the original system and incorporates on-line process control systems. The IBA determines bond strength by measuring changes in pulsar ultrasonic waves injected into a board. Analysis of the wave determines the average internal bond strength for the panel. Results are displayed immediately. Using the system, a mill operator can adjust resin/wood proportion, reduce setup time and waste, produce internal bonds of a consistent quality and automatically mark deficient products.

Preliminary investigation of biological resistance, water absorption and swelling of thermally compressed pine wood panels

Treesearch

Oner Unsal; S. Nami Kartal; Zeki Candan; Rachel Arango; Carol A. Clausen; Frederick Green

2008-01-01

Wood can be modified by compressive, thermal and chemical treatments. Compression of wood under thermal conditions is resulted in densification of wood. This study evaluated decay and termite resistance of thermally compressed pine wood panels at either 5 or 7 MPa and at either 120 or 150°C for one hour. The process caused increases in density and decreases in...

Wood-based panel plant locations and timber availability in selected U.S. states

Treesearch

T. McKeever; H. N. Spelter

1998-01-01

This report lists wood-based panel industry plant locations, production capacities, timber inventories, and wood costs for 24 U.S. states. Industry sectors covered include medium-density fiberboard, particleboard, softwood plywood, and oriented strandboard. Maps of major forest producing states show plant locations and the underlying density of timber stocking by...

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1LIGHT THREE PANEL WOOD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR OF KITCHEN/UTILITY AREA SHOWING 1-LIGHT THREE PANEL WOOD OUTSIDE DOOR SOUTH SIDE OF HOUSE, PLUMBING HOOKUPS FOR WASHER BELOW BUILT-IN CABINETS AT PHOTO LEFT, AND PAIRED ARRANGEMENTS OF 4-LIGHT OVER 4-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS ON SOUTH AND WEST WALLS. VIEW TO SOUTH. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Cord Wood Testing in a Non-Catalytic Wood Stove

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butcher, T.; Trojanowski, R.; Wei, G.

EPA Method 28 and the current wood stove regulations have been in-place since 1988. Recently, EPA proposed an update to the existing NSPS for wood stove regulations which includes a plan to transition from the current crib wood fuel to cord wood fuel for certification testing. Cord wood is seen as generally more representative of field conditions while the crib wood is seen as more repeatable. In any change of certification test fuel, there are questions about the impact on measured results and the correlation between tests with the two different fuels. The purpose of the work reported here ismore » to provide data on the performance of a noncatalytic stove with cord wood. The stove selected has previously been certified with crib wood which provides a basis for comparison with cord wood. Overall, particulate emissions were found to be considerably higher with cord wood.« less

Static in-plane shear behaviour of prefabricated wood-wool panel wallettes

NASA Astrophysics Data System (ADS)

Noh, M. S. Md; Ahmad, Z.; Ibrahim, A.; Kamarudin, A. F.; Mokhatar, S. N.

2018-04-01

The green construction material and technique are the current issue toward improving sustainability in the construction industry in Malaysia. The use of construction material that produced from renewable resources is a part of the effort for greening this industry. WWCP (Wood-wool cement panel) is a wood based product available to the construction industry to be used as a structural building wall element. This renewable material has the potential to replace the less eco-friendly materials such as bricks and other masonry element. However, the behaviour of wall subjected to the different load conditions is not well established and therefore, this study aimed to investigate the structural behaviour of the small scale wall (wallettes) subjected to in-plane lateral load. As a comparison, two types of fabrication technique of wallettes with dimension of 1200 mm × 1200 mm (± 30 mm) were considered. The conventional vertical stacking technique was denoted as W1 and new propose techniques (cross laminated) was denoted as W2. Three replicates of each type were fabricated and tested under in-plane lateral load until failure. The test results revealed that, the wallettes fabricated using the new fabrication technique significantly increased two times in load carrying capacity compared to wallettes with conventional technique.

Experimental and Theoretical Modal Analysis of Full-Sized Wood Composite Panels Supported on Four Nodes

PubMed Central

Guan, Cheng; Zhang, Houjiang; Wang, Xiping; Miao, Hu; Zhou, Lujing; Liu, Fenglu

2017-01-01

Key elastic properties of full-sized wood composite panels (WCPs) must be accurately determined not only for safety, but also serviceability demands. In this study, the modal parameters of full-sized WCPs supported on four nodes were analyzed for determining the modulus of elasticity (E) in both major and minor axes, as well as the in-plane shear modulus of panels by using a vibration testing method. The experimental modal analysis was conducted on three full-sized medium-density fiberboard (MDF) and three full-sized particleboard (PB) panels of three different thicknesses (12, 15, and 18 mm). The natural frequencies and mode shapes of the first nine modes of vibration were determined. Results from experimental modal testing were compared with the results of a theoretical modal analysis. A sensitivity analysis was performed to identify the sensitive modes for calculating E (major axis: Ex and minor axis: Ey) and the in-plane shear modulus (Gxy) of the panels. Mode shapes of the MDF and PB panels obtained from modal testing are in a good agreement with those from theoretical modal analyses. A strong linear relationship exists between the measured natural frequencies and the calculated frequencies. The frequencies of modes (2, 0), (0, 2), and (2, 1) under the four-node support condition were determined as the characteristic frequencies for calculation of Ex, Ey, and Gxy of full-sized WCPs. The results of this study indicate that the four-node support can be used in free vibration test to determine the elastic properties of full-sized WCPs. PMID:28773043

Review of wood-based panel sector in United States and Canada

Treesearch

H. N. Spelter; D. B. McKeever; I. Durbak

1997-01-01

Structural and nonstructural panels have been the fastest growing sector among wood products for the past two decades. The recent spate of plant construction and drop in product prices indicate slower growth and consolidation in the next 2 years. Growth in demand is unlikely to catch up with projected capacities until the next century, unless attrition of some existing...

Significance of wood extractives for wood bonding.

PubMed

Roffael, Edmone

2016-02-01

Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

Fuzzy logic applied to prospecting for areas for installation of wood panel industries.

PubMed

Dos Santos, Alexandre Rosa; Paterlini, Ewerthon Mattos; Fiedler, Nilton Cesar; Ribeiro, Carlos Antonio Alvares Soares; Lorenzon, Alexandre Simões; Domingues, Getulio Fonseca; Marcatti, Gustavo Eduardo; de Castro, Nero Lemos Martins; Teixeira, Thaisa Ribeiro; Dos Santos, Gleissy Mary Amaral Dino Alves; Juvanhol, Ronie Silva; Branco, Elvis Ricardo Figueira; Mota, Pedro Henrique Santos; da Silva, Lilianne Gomes; Pirovani, Daiani Bernardo; de Jesus, Waldir Cintra; Santos, Ana Carolina de Albuquerque; Leite, Helio Garcia; Iwakiri, Setsuo

2017-05-15

Prospecting for suitable areas for forestry operations, where the objective is a reduction in production and transportation costs, as well as the maximization of profits and available resources, constitutes an optimization problem. However, fuzzy logic is an alternative method for solving this problem. In the context of prospecting for suitable areas for the installation of wood panel industries, we propose applying fuzzy logic analysis for simulating the planting of different species and eucalyptus hybrids in Espírito Santo State, Brazil. The necessary methodological steps for this study are as follows: a) agriclimatological zoning of different species and eucalyptus hybrids; b) the selection of the vector variables; c) the application of the Euclidean distance to the vector variables; d) the application of fuzzy logic to matrix variables of the Euclidean distance; and e) the application of overlap fuzzy logic to locate areas for installation of wood panel industries. Among all the species and hybrids, Corymbia citriodora showed the highest percentage values for the combined very good and good classes, with 8.60%, followed by Eucalyptus grandis with 8.52%, Eucalyptus urophylla with 8.35% and Urograndis with 8.34%. The fuzzy logic analysis afforded flexibility in prospecting for suitable areas for the installation of wood panel industries in the Espírito Santo State can bring great economic and social benefits to the local population with the generation of jobs, income, tax revenues and GDP increase for the State and municipalities involved. The proposed methodology can be adapted to other areas and agricultural crops. Copyright © 2017 Elsevier Ltd. All rights reserved.

Properties of structural panels fabricated from bioremediated CCA-treated wood: pilot scale

Treesearch

Carol A. Clausen; James H. Muehl; Andrzej M. Krzysik

2006-01-01

Particleboard and flakeboard panels were fabricated from remediated CCA-treated southern yellow pine. Treated wood, flaked or comminuted into particles, was remediated in 12-kg batches using oxalic acid extraction, followed by bioleaching with the metal-tolerant bacterium Bacillus licheniformis. Remediation resulted in removal of 80 percent Cu, 71 percent Cr, and 89...

Experimental and theoretical modal analysis of full-sized wood composite panels supported on four nodes

Treesearch

Cheng Guan; Houjiang Zhang; Xiping Wang; Hu Miao; Lujing Zhou; Fenglu Liu

2017-01-01

Key elastic properties of full-sized wood composite panels (WCPs) must be accurately determined not only for safety, but also serviceability demands. In this study, the modal parameters of full-sized WCPs supported on four nodes were analyzed for determining the modulus of elasticity (E) in both major and minor axes, as well as the in-plane shear modulus of panels by...

Comparison of Wood Composite Properties Using Cantilever-Beam Bending

Treesearch

Houjiang Zhang; John F. Hunt; Lujing Zhou

2015-01-01

Wood-based composite panels generally are first tested out-of-plane in the primarypanel directionfollowed by the cross panel direction, but rarely edgewise. While most applications use wood-based composites in the flat-wise orientation and only need the out-of-plane properties, there are construction configurations where edgewise properties are needed for improved...

Orthogonal model and experimental data for analyzing wood-fiber-based tri-axial ribbed structural panels in bending

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2017-01-01

This paper presents an analysis of 3-dimensional engineered structural panels (3DESP) made from wood-fiber-based laminated paper composites. Since the existing models for calculating the mechanical behavior of core configurations within sandwich panels are very complex, a new simplified orthogonal model (SOM) using an equivalent element has been developed. This model...

Titanium Honeycomb Panel Testing

NASA Technical Reports Server (NTRS)

Richards, W. Lance; Thompson, Randolph C.

1996-01-01

Thermal-mechanical tests were performed on a titanium honeycomb sandwich panel to experimentally validate the hypersonic wing panel concept and compare test data with analysis. Details of the test article, test fixture development, instrumentation, and test results are presented. After extensive testing to 900 deg. F, non-destructive evaluation of the panel has not detected any significant structural degradation caused by the applied thermal-mechanical loads.

Development of fire-resistant wood structural panels

NASA Technical Reports Server (NTRS)

Vaughan, T. W.; Etzold, R.

1977-01-01

Structural panels made with Xylok 210 resin as the binder had a burn-through resistance at least equal to the structural panels made with Kerimid 500. Therefore, because of its comparative ease of handling, Xylok 210 was selected as the resin binder to provide the baseline panel for the study of a means of improving the flame-spread resistance of the structural panels. The final resin-filler system consisted of Xylok 210 binder with the addition of ammonium oxalate and ammonium phosphate to the strands of the surface layers, using 24% of each salt based upon the air-dry weight of the strands. This system resulted in a panel with a flame-spread code of about 60, a Class 2 classification. A standard phenolic based structural panel had a flame-spread greater than 200 for laboratory prepared panels. The burn-through tests indicated an average burn-through time of 588 seconds for the specimens made with the final system. This compares to an average burn-through time of 287 seconds for the standard phenolic base structural specimen. One full-size panel was made with the final system.

Wood-based composites and panel products

Treesearch

John A. Youngquist

1999-01-01

Because wood properties vary among species, between trees of the same species, and between pieces from the same tree, solid wood cannot match reconstituted wood in the range of properties that can be controlled in processing. When processing variables are properly selected, the end result can sometimes surpass nature’s best effort. With solid wood, changes in...

Corrosion of metals in wood : comparing the results of a rapid test method with long-term exposure tests across six wood treatments

Treesearch

Samuel L. Zelinka; Donald S. Stone

2011-01-01

This paper compares two methods of measuring the corrosion of steel and galvanized steel in wood: a long-term exposure test in solid wood and a rapid test method where fasteners are electrochemically polarized in extracts of wood treated with six different treatments. For traditional wood preservatives, the electrochemical extract method correlates with solid wood...

Furniture wood wastes: Experimental property characterisation and burning tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna

2009-10-15

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675more » to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.« less

Simplified analytical model and balanced design approach for light-weight wood-based structural panel in bending

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2016-01-01

This paper presents a simplified analytical model and balanced design approach for modeling lightweight wood-based structural panels in bending. Because many design parameters are required to input for the model of finite element analysis (FEA) during the preliminary design process and optimization, the equivalent method was developed to analyze the mechanical...

Performance evaluation of cross-flow membrane system for wastewater reuse from the wood-panels industry.

PubMed

Dizge, Nadir

2014-01-01

The objectives of this investigation were to perform a series of lab-scale membrane separation experiments under various operating conditions to investigate the performance behaviour of nanofiltration membrane (NF 270) for wastewater reuse from the wood-panels industry. The operating condition effects, e.g. cross-flow velocity (CFV), trans membrane pressure (TMP) and temperature, on the permeate flux and contaminant rejection efficiency were investigated. Moreover, three different samples: (1) raw wastewater collected from the wood-panels industry; (2) ultrafiltration pre-treated wastewater (UF-NF); and (3) coagulation/flocculation pre-treated wastewater (CF-NF) were employed in this study. The UF-NF was proposed as a pre-treatment process because it could reduce the chemical oxygen demand (COD) effectively with lower energy consumption than CF-NF. The performance of NF 270 membrane was assessed by measurements of the many parameters (pH, conductivity, total dissolved solids, COD, suspended solids, total nitrogen, nitrite, nitrate, and total phosphate) under various operating conditions. It was noted that the contaminant rejection was affected by changing TMP and CFV. It was concluded that the purified water stream can be recycled into the process for water reuse or safely disposed to the river.

 Thermal Insulation System Made of Wood and Paper for Use in Residential Construction

Treesearch

Zoltán Pásztory; Tibor Horváth; Samuel V. Glass; Samuel L. Zelinka

2015-01-01

This article introduces an insulation system that takes advantage of the low thermal conductivity of still air and is made of wood and paper. The insulation, called the Mirrorpanel, is constructed as a panel of closely spaced layers of coated paper and held together in a frame of wood or fiberboard. Panels have been fabricated and tested at the laboratory scale, whole...

Acoustic testing of high temperature panels

NASA Technical Reports Server (NTRS)

Leatherwood, Jack D.; Clevenson, Sherman A.; Powell, Clemans A.; Daniels, Edward F.

1990-01-01

Results are presented of a series of thermal-acoustic tests conducted on the NASA Langley Research Center Thermal-Acoustic Test Apparatus to (1) investigate techniques for obtaining strain measurements on metallic and carbon-carbon materials at elevated temperature; (2) document the dynamic strain response characteristics of several superalloy honeycomb thermal protection system panels at elevated temperatures of up to 1200 F; and (3) determine the strain response and sonic fatigue behavior of four carbon-carbon panels at both ambient and elevated temperatures. A second study tested four carbon-carbon panels to document panel dynamic response characteristics at ambient and elevated temperature, determine time to failure and faliure modes, and collect continuous strain data up to panel failure. Strain data are presented from both types of panels, and problems encountered in obtaining reliable strain data on the carbon-carbon panels are described. The failure modes of the carbon-carbon panels are examined.

Orbiter radiator panel solar focusing test

NASA Technical Reports Server (NTRS)

Howell, H. R.

1982-01-01

A test was conducted to determine the solar reflections from the Orbiter radiator panels. A one-tenth scale model of the forward and mid-forward radiator panels in the deployed position was utilized in the test. Test data was obtained to define the reflected one-sun envelope for the embossed silver/Teflon radiator coating. The effects of the double contour on the forward radiator panels were included in the test. Solar concentrations of 2 suns were measured and the one-sun envelope was found to extend approximately 86 inches above the radiator panel. A limited amount of test data was also obtained for the radiator panels with the smooth silver/Teflon coating to support the planned EVA on the Orbiter STS-5 flight. Reflected solar flux concentrations as high as 8 suns were observed with the smooth coating and the one-sun envelope was determined to extend 195 inches above the panel. It is recommended that additional testing be conducted to define the reflected solar environment beyond the one-sun boundary.

Wood particleboard and flakeboard : types, grades, and uses

Treesearch

C. G. Carll

1986-01-01

This report is for those who use or may want to use wood particleboard. The term bparticleboardc is used as defined in the American Society for Testing and Materials (ASTM) Standard D 1554, which includes flakeboards as a subclass of particleboards, and not as used in the lumber trade where the term is usually reserved for panels made of fine wood particles such as...

Evaluating the warping of laminated particleboard panels

Treesearch

Zhiyong Cai

2004-01-01

Laminated wood composites have been used widely in the secondary manufacturing processes in the wood panel industries. Warping, which is defined as the out-of-plane deformation of an initially flat panel, is a longstanding problem associated with the use of laminated wood composites. The mechanism of warping is still not fully understood. A new two- dimensional warping...

Structural and thermal testing of lightweight reflector panels

NASA Technical Reports Server (NTRS)

Mcgregor, J.; Helms, R.; Hill, T.

1992-01-01

The paper describes the test facility developed for testing large lightweight reflective panels with very accurate and stable surfaces, such as the mirror panels of composite construction developed for the NASA's Precision Segmented Reflector (PSR). Special attention is given to the panel construction and the special problems posed by the characteristics of these panels; the design of the Optical/Thermal Vacuum test facility for structural and thermal testing, developed at the U.S. AFPL; and the testing procedure. The results of the PSR panel test program to date are presented. The test data showed that the analytical approaches used for the panel design and for the prediction of the on-orbit panel behavior were adequate.

Wood and Other Materials Used to Construct Nonresidential Buildings - Canada

Treesearch

David B. McKeever; Joe Elling

2014-01-01

Low-rise nonresidential building construction is an important market in Canada for lumber, engineered wood products, structural wood panels, and nonstructural wood panels. This report examines wood products consumption in 2012 for construction of selected low-rise nonresidential buildings types that have six or fewer stories. Buildings with more than six stories are...

Orbiter radiator panel solar focusing test

NASA Technical Reports Server (NTRS)

Howell, H. R.; Rankin, J. G.

1983-01-01

Test data are presented which define the area around the Orbiter radiator panels for which the solar reflections are concentrated to one-sun or more. The concave shape of the panels and their specular silver/Teflon coating causes focusing of the reflected solar energy which could have adverse heating effects on equipment or astronaut extravehicular activity (EVA) in the vicinity of the radiator panels. A room ambient test method was utilized with a one-tenth scale model of the radiator panels.

Electrochemical corrosion testing of fasteners in extracts of treated wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; Donald S. Stone

2008-01-01

A recent change in wood preservatives has highlighted the need for a rapid, quantitative test to measure the corrosion rates of metals in contact with treated wood that could be used to evaluate new fasteners or new wood preservatives. A new method was developed where polarisation resistance tests were conducted on fasteners exposed to a water extract of wood treated...

Wood preservative testing

Treesearch

Rebecca Ibach; Stan T. Lebow

2012-01-01

Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

Gene panel testing for inherited cancer risk.

PubMed

Hall, Michael J; Forman, Andrea D; Pilarski, Robert; Wiesner, Georgia; Giri, Veda N

2014-09-01

Next-generation sequencing technologies have ushered in the capability to assess multiple genes in parallel for genetic alterations that may contribute to inherited risk for cancers in families. Thus, gene panel testing is now an option in the setting of genetic counseling and testing for cancer risk. This article describes the many gene panel testing options clinically available to assess inherited cancer susceptibility, the potential advantages and challenges associated with various types of panels, clinical scenarios in which gene panels may be particularly useful in cancer risk assessment, and testing and counseling considerations. Given the potential issues for patients and their families, gene panel testing for inherited cancer risk is recommended to be offered in conjunction or consultation with an experienced cancer genetic specialist, such as a certified genetic counselor or geneticist, as an integral part of the testing process. Copyright © 2014 by the National Comprehensive Cancer Network.

4. "TEST CONDUCTORS PANEL AT TEST STAND 1A, DIRECTORATE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. "TEST CONDUCTORS PANEL AT TEST STAND 1-A, DIRECTORATE OF MISSILE CAPTIVE TEST, EDWARDS AFB, 15 JAN 58, 3098.58." A photograph of the control room, with seven men watching monitors and instrument panels. Photo no. "3098 58; G-AFFTC 15 JAN 58; Test Conductors Panel T.S. 1-A". - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Control Center, Test Area 1-115, near Altair & Saturn Boulevards, Boron, Kern County, CA

Physical and mechanical properties of bio-composites from wood particles and liquefied wood resin

Treesearch

Hui Pan; Todd F. Shupe; Chung-Yun Hse

2009-01-01

Compression molded composites were made from wood particles and a liquefied wood/phenol/formaldehyde co-condensed resin. Based on our previous research, a phenol to wood (P/W) ratio of 2/1 was chosen for this study. The two experimental variables selected were: 1) liquefaction temperature (150o and 180oC) and 2) cooking method (atmospheric and sealed). Panels were...

Combined Loads Test Fixture for Thermal-Structural Testing Aerospace Vehicle Panel Concepts

NASA Technical Reports Server (NTRS)

Fields, Roger A.; Richards, W. Lance; DeAngelis, Michael V.

2004-01-01

A structural test requirement of the National Aero-Space Plane (NASP) program has resulted in the design, fabrication, and implementation of a combined loads test fixture. Principal requirements for the fixture are testing a 4- by 4-ft hat-stiffened panel with combined axial (either tension or compression) and shear load at temperatures ranging from room temperature to 915 F, keeping the test panel stresses caused by the mechanical loads uniform, and thermal stresses caused by non-uniform panel temperatures minimized. The panel represents the side fuselage skin of an experimental aerospace vehicle, and was produced for the NASP program. A comprehensive mechanical loads test program using the new test fixture has been conducted on this panel from room temperature to 500 F. Measured data have been compared with finite-element analyses predictions, verifying that uniform load distributions were achieved by the fixture. The overall correlation of test data with analysis is excellent. The panel stress distributions and temperature distributions are very uniform and fulfill program requirements. This report provides details of an analytical and experimental validation of the combined loads test fixture. Because of its simple design, this unique test fixture can accommodate panels from a variety of aerospace vehicle designs.

Direct current testing to measure corrosiveness of wood preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; Donald S. Stone; James T. Gilbertson

2007-01-01

A qualitative test that mimics the corrosion behaviour of metals in contact with treated wood without using wood specimens would be of great value in rapidly evaluating the corrosiveness of new wood preservatives. The objective of this study was to determine whether the linear polarisation resistance of metals immersed in a solution of preservative chemicals is related...

Pressure Testing of a Minimum Gauge PRSEUS Panel

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew J.; Rouse, Marshall; Linton, Kim A.; Li, Victor P.

2011-01-01

Advanced aircraft configurations that have been developed to increase fuel efficiency require advanced, novel structural concepts capable of handling the unique load conditions that arise. One such concept is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) developed by the Boeing Company. The PRSEUS concept is being investigated by NASA s Environmentally Responsible Aviation (ERA) Program for use in a hybrid-wing body (HWB) aircraft. This paper summarizes the analysis and test of a PRSEUS panel subjected to internal pressure, the first such pressure test for this structural concept. The pressure panel used minimum gauge skin, with stringer and frame configurations consistent with previous PRSEUS tests. Analysis indicated that for the minimum gauge skin panel, the stringer locations exhibit fairly linear response, but the skin bays between the stringers exhibit nonlinear response. Excellent agreement was seen between nonlinear analysis and test results in the critical portion at the center of the panel. The pristine panel was capable of withstanding the required 18.4 psi pressure load condition without exhibiting any damage. The impacted panel was capable of withstanding a pressure load in excess of 28 psi before initial failure occurred at the center stringer, and the panel was capable of sustaining increased pressure load after the initial failure. This successful PRSEUS panel pressure panel test was a critical step in the building block approach for enabling the use of this advanced structural concept on future aircraft, such as the HWB.

Some Properties of Composite Panels Made from Wood Flour and Recycled Polyethylene

PubMed Central

Ozdemir, Turgay; Mengeloglu, Fatih

2008-01-01

This study investigated the effect of board type (unmodified vs. MAPE modified) on the surface quality and thickness swelling-water absorption properties of recycled high density polyethylene (HDPE) based wood plastic composites. Additionally, two commercially available coatings (cellulosic coating and polyurethane lacquer coating) were also applied to composite surfaces and their adhesion strength, abrasion and scratch resistance, and gloss values were determined. This study showed that modification of the composites with MAPE coupling agent increased the surface smoothness and reduced the water absorption and thickness swelling of the panels. Abrasion resistance of the composites was also improved through MAPE modification. Regardless of board type, higher scratch resistance and gloss values were observed for polyurethane lacquer coated samples compared to those of cellulosic varnish coated ones. Improvement of adhesion strength was also seen on SEM micrographs. PMID:19330092

Airborne sound transmission loss characteristics of wood-frame construction

NASA Astrophysics Data System (ADS)

Rudder, F. F., Jr.

1985-03-01

This report summarizes the available data on the airborne sound transmission loss properties of wood-frame construction and evaluates the methods for predicting the airborne sound transmission loss. The first part of the report comprises a summary of sound transmission loss data for wood-frame interior walls and floor-ceiling construction. Data bases describing the sound transmission loss characteristics of other building components, such as windows and doors, are discussed. The second part of the report presents the prediction of the sound transmission loss of wood-frame construction. Appropriate calculation methods are described both for single-panel and for double-panel construction with sound absorption material in the cavity. With available methods, single-panel construction and double-panel construction with the panels connected by studs may be adequately characterized. Technical appendices are included that summarize laboratory measurements, compare measurement with theory, describe details of the prediction methods, and present sound transmission loss data for common building materials.

Test evaluation of a laminated wood wind turbine blade concept

NASA Technical Reports Server (NTRS)

Faddoul, J. R.

1981-01-01

A series of tests conducted on a root end section of a laminated wood wind turbine blade are reported. The blade to hub transition of the wood blade uses steel studs cast into the wood D spar with a filled epoxy. Both individual studs and a full scale, short length, root section were tested. Results indicate that the bonded stud concept is more than adequate for both the 30 year life fatigue loads and for the high wind or hurricane gust loads.

Supersonic Panel Flutter Test Results for Flat Fiber-Glass Sandwich Panels with Foamed Cores

NASA Technical Reports Server (NTRS)

Tuovila, W. J.; Presnell, John G., Jr.

1961-01-01

Flutter tests have been made on flat panels having a 1/4 inch-thick plastic-foam core covered with thin fiber-glass laminates. The testing was done in the Langley Unitary Plan wind tunnel at Mach numbers from 1.76 t o 2.87. The flutter boundary for these panels was found to be near the flutter boundary of thin metal panels when compared on the basis of an equivalent panel stiffness. The results also demonstrated that the depth of the cavity behind the panel has a pronounced influence on flutter. Changing the cavity depth from 1 1/2 inches to 1/2 inch reduced the dynamic pressure at start of flutter by 40 percent. No flutter was obtained when the spacers on the back of the panel were against the bottom of the cavity.

Prediction of obeche wood-induced asthma by specific skin prick testing.

PubMed

Hannu, T; Lindström, I; Palmroos, P; Kuuliala, O; Sauni, R

2013-09-01

It has previously been shown that a positive skin prick test (SPT) result is a good predictor of a positive specific inhalation challenge (SIC) in patients with occupational asthma (OA) related to wheat or rye flours. This association has not been previously studied in OA attributable to obeche wood. To describe a clinical series of patients with OA induced by obeche wood. To investigate if the SPT result can be used as a predictor for the outcome of SIC tests. OA was diagnosed according to patient history, lung function examinations and SIC tests, as well as the determination of obeche SPTs. We analysed sensitivity, specificity and positive (PPV) and negative predictive values (NPV) at different wheal sizes of the SPTs and drew receiver-operating characteristic plots using the SIC test result as the gold standard. Obeche wood SIC tests were performed on 34 symptomatic workers. Of these, 27 workers had a positive test result and were diagnosed as having OA. The minimal cut-off value with a PPV of 100% was an SPT wheal of 3.5 mm from obeche wood. This means that all workers with a wheal size of ≥ 3.5 mm from obeche wood had a positive SIC. Positive SPT results in symptomatic workers were good predictors of a positive SIC. SIC with obeche wood may be unnecessary in strongly sensitized workers.

Isocyanate and total inhalable particulate air measurements in the European wood panel industry.

PubMed

Vangronsveld, E; Berckmans, S; Verbinnen, K; Van Leeuw, C; Bormans, C

2010-11-01

It is well known that the use of MDI (methylene diphenyldiisocyanate) as an alternative for formaldehyde-based resins is seen as a responsible option to reduce formaldehyde emissions for CWP (Composite Wood Products) in buildings. However, there are concerns raised regarding the exposure risk of workers. The purpose of this article is to provide the reader with factual information to demonstrate that the use of MDI compared to other agents used in CWP production processes does not pose increased inhalation exposure risks for workers. Personal and area air measurements were carried out at nine Composite Wood Panel plants throughout Europe to assess potential inhalation exposures to MDI and wood dust as Total Inhalable Particulates (TIP). In total, 446 pairs of samples were collected for MDI and TIP of which 283 pairs were personal samples and the remaining 163 pairs were area samples collected at key locations along the production line. This data together with published formaldehyde exposure data has been used to evaluate the exposure safety margin opposite what are considered relevant occupational exposure limits. The methods used for sampling and analysing MDI and TIP are based on internationally accepted methods, i.e. MDHS 25/3 (or ISO 16702) for MDI, and MDHS 14/3 for TIP. The job functions with an increased exposure profile for TIP were the cleaners, drying operators and quality control staff, and for MDI, the cleaners and quality control staff. The areas with an increased exposure profile for TIP are the conveyor area from OSB blender to former area and the OSB press infeed, and for MDI the OSB weigh belt and OSB former bin area. The exposure safety margin opposite the selected exposure limits can be ranked as MDI>TIP>formaldehyde (high margin of safety to low margin of safety), indicating that the use of MDI also reduces the exposure risks to workers during production of CWP compared to formaldehyde. By reducing the airborne TIP concentrations, a respiratory

Outgassing tests on iras solar panel samples

NASA Technical Reports Server (NTRS)

Premat, G.; Zwaal, A.; Pennings, N. H.

1980-01-01

Several outgassing tests were carried out on representative solar panel samples in order to determine the extent of contamination that could be expected from this source. The materials for the construction of the solar panels were selected as a result of contamination obtained in micro volatile condensable materials tests.

The Space Station Photovoltaic Panels Plasma Interaction Test Program: Test plan and results

NASA Technical Reports Server (NTRS)

Nahra, Henry K.; Felder, Marian C.; Sater, Bernard L.; Staskus, John V.

1989-01-01

The Plasma Interaction Test performed on two space station solar array panels is addressed. This includes a discussion of the test requirements, test plan, experimental set-up, and test results. It was found that parasitic current collection was insignificant (0.3 percent of the solar array delivered power). The measured arcing threshold ranged from -210 to -457 V with respect to the plasma potential. Furthermore, the dynamic response of the panels showed the panel time constant to range between 1 and 5 microsec, and the panel capacitance to be between .01 and .02 microF.

The Space Station photovoltaic panels plasma interaction test program - Test plan and results

NASA Technical Reports Server (NTRS)

Nahra, Henry K.; Felder, Marian C.; Sater, Bernard L.; Staskus, John V.

1990-01-01

The plasma Interaction Test performed on two space station solar array panels is addressed. This includes a discussion of the test requirements, test plan, experimental set-up, and test results. It was found that parasitic current collection was insignificant (0.3 percent of the solar array delivered power). The measured arcing threshold ranged from -210 to -457 V with respect to the plasma potential. Furthermore, the dynamic response of the panels showed the panel time constant to range between 1 and 5 microsec, and the panel capacitance to be between .01 and .02 microF.

Gene panel testing for hereditary breast cancer.

PubMed

Winship, Ingrid; Southey, Melissa C

2016-03-21

Inherited predisposition to breast cancer is explained only in part by mutations in the BRCA1 and BRCA2 genes. Most families with an apparent familial clustering of breast cancer who are investigated through Australia's network of genetic services and familial cancer centres do not have mutations in either of these genes. More recently, additional breast cancer predisposition genes, such as PALB2, have been identified. New genetic technology allows a panel of multiple genes to be tested for mutations in a single test. This enables more women and their families to have risk assessment and risk management, in a preventive approach to predictable breast cancer. Predictive testing for a known family-specific mutation in a breast cancer predisposition gene provides personalised risk assessment and evidence-based risk management. Breast cancer predisposition gene panel tests have a greater diagnostic yield than conventional testing of only the BRCA1 and BRCA2 genes. The clinical validity and utility of some of the putative breast cancer predisposition genes is not yet clear. Ethical issues warrant consideration, as multiple gene panel testing has the potential to identify secondary findings not originally sought by the test requested. Multiple gene panel tests may provide an affordable and effective way to investigate the heritability of breast cancer.

Hybrid TE panel test results

NASA Technical Reports Server (NTRS)

Bifano, W. J.

1972-01-01

Test results are presented for a nine couple (3 x 3 array) thermoelectric panel of hybrid thermocouples. In the hybrid couple, a hollow cylinder of p-type Si-Ge is used to encapsulate a segmented PbTe/Si-Ge n-leg. The hybrid couple is predicted to offer a 10- to 15-percent improvement in performance relative to all Si-Ge couples. The efficiency, output power, and internal resistance of the panel as well as the resistances of the individual hybrid couples are presented as a function of test time covering a period of more than 2600 hours. Initial test results indicated hybrid couple performance consistent with design predictions. Extraneous resistance ranged from 20 to 25% of the hybrid couple thermoelectric resistance.

Shear-Panel Test Fixture Eliminates Corner Stresses

NASA Technical Reports Server (NTRS)

Kiss, J. J.; Farley, G. L.; Baker, D. J.

1984-01-01

New design eliminates corner stresses while maintaining uniform stress across panel. Shear panel test fixture includes eight frames and eight corner pins. Fixture assembled in two halves with shear panel sandwiched in between. Results generated from this fixture will result in good data base for design of efficient aircraft structures and other applications.

Southern Exports of Wood Products 1968-80

Treesearch

Harold W. Wisdom; James E. Granskog; R. J. Peeler

1983-01-01

Exports of wood products from the South have risen sharply since the mid 1970's. Lumber shipments are the largest export group, while panel products have exhibited the fastest growth. Hardwood logs, wood chips, and prefabricated wooden structures have been the primary contributors to the growth of roundwood and miscellaneous wood product exports. Western Europe...

Preparation and testing of plant seed meal-based wood adhesives.

PubMed

He, Zhongqi; Chapital, Dorselyn C

2015-03-05

Recently, the interest in plant seed meal-based products as wood adhesives has steadily increased, as these plant raw materials are considered renewable and environment-friendly. These natural products may serve as alternatives to petroleum-based adhesives to ease environmental and sustainability concerns. This work demonstrates the preparation and testing of the plant seed-based wood adhesives using cottonseed and soy meal as raw materials. In addition to untreated meals, water washed meals and protein isolates are prepared and tested. Adhesive slurries are prepared by mixing a freeze-dried meal product with deionized water (3:25 w/w) for 2 hr. Each adhesive preparation is applied to one end of 2 wood veneer strips using a brush. The tacky adhesive coated areas of the wood veneer strips are lapped and glued by hot-pressing. Adhesive strength is reported as the shear strength of the bonded wood specimen at break. Water resistance of the adhesives is measured by the change in shear strength of the bonded wood specimens at break after water soaking. This protocol allows one to assess plant seed-based agricultural products as suitable candidates for substitution of synthetic-based wood adhesives. Adjustments to the adhesive formulation with or without additives and bonding conditions could optimize their adhesive properties for various practical applications.

Attic Retrofits Using Nail-Base Insulated Panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, David; Kochkin, Vladimir

This project developed and demonstrated a roof/attic energy retrofit solution using nail-base insulated panels for existing homes where traditional attic insulation approaches are not effective or feasible. Nail-base insulated panels (retrofit panels) consist of rigid foam insulation laminated to one face of a wood structural panel. The prefabricated panels are installed above the existing roof deck during a reroofing effort.

Exposure test of fasteners in preservative-treated wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2006-01-01

This study examined nails and screws exposed to ACQ-treated wood for up to 12 months in a controlled environment. The environment (27ºC, 100% relative humidity) was chosen so that comparisons could be made with previous exposure tests run using CCA-treated wood in the same environment. Five types of fasteners (common 8d nail, hot-dipped galvanized 8d nail, 4d aluminum...

Test results from large wing and fuselage panels

NASA Technical Reports Server (NTRS)

Madan, Ram C.; Voldman, Mike

1993-01-01

This paper presents the first results in an assessment of the strength, stiffness, and damage tolerance of stiffened wing and fuselage subcomponents. Under this NASA funded program, 10 large wing and fuselage panels, variously fabricated by automated tow placement and dry-stitched preform/resin transfer molding, are to be tested. The first test of an automated tow placement six-longeron fuselage panel under shear load was completed successfully. Using NASTRAN finite-element analysis the stiffness of the panel in the linear range prior to buckling was predicted within 3.5 percent. A nonlinear analysis predicted the buckling load within 10 percent and final failure load within 6 percent. The first test of a resin transfer molding six-stringer wing panel under compression was also completed. The panel failed unexpectedly in buckling because of inadequate supporting structure. The average strain was 0.43 percent with a line load of 20.3 kips per inch of width. This strain still exceeds the design allowable strains. Also, the stringers did not debond before failure, which is in contrast to the general behavior of unstitched panels.

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2008

Treesearch

David McKeever

2010-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only. Buildings with five or more stories are normally severely restricted by building code from being wood...

Preparation and Testing of Plant Seed Meal-based Wood Adhesives

PubMed Central

He, Zhongqi; Chapital, Dorselyn C.

2015-01-01

Recently, the interest in plant seed meal-based products as wood adhesives has steadily increased, as these plant raw materials are considered renewable and environment-friendly. These natural products may serve as alternatives to petroleum-based adhesives to ease environmental and sustainability concerns. This work demonstrates the preparation and testing of the plant seed-based wood adhesives using cottonseed and soy meal as raw materials. In addition to untreated meals, water washed meals and protein isolates are prepared and tested. Adhesive slurries are prepared by mixing a freeze-dried meal product with deionized water (3:25 w/w) for 2 hr. Each adhesive preparation is applied to one end of 2 wood veneer strips using a brush. The tacky adhesive coated areas of the wood veneer strips are lapped and glued by hot-pressing. Adhesive strength is reported as the shear strength of the bonded wood specimen at break. Water resistance of the adhesives is measured by the change in shear strength of the bonded wood specimens at break after water soaking. This protocol allows one to assess plant seed-based agricultural products as suitable candidates for substitution of synthetic-based wood adhesives. Adjustments to the adhesive formulation with or without additives and bonding conditions could optimize their adhesive properties for various practical applications. PMID:25867092

Application of laboratory fungal resistance tests to solid wood and wood-plastic composite

Treesearch

Craig Merrill Clemons; Rebecca E. Ibach

2003-01-01

The fungal resistance of high density polyethylene filled with 50% wood flour was investigated using laboratory soil block tests. Modifications to standard test methods were made to increase initial moisture content, increase exposure surface area, and track moisture content, mechanical properties, and weight loss over the exposure period. Mechanical properties...

Identification of test methods for determining wood guardrail post integrity.

DOT National Transportation Integrated Search

2015-06-01

Wood guardrail posts are subject to decay and deterioration, yet most DOTs have minimal or no : inspection procedures in place for wood guardrail posts. The objective of this study was to : identify nondestructive testing technologies to assess the c...

Fire containment tests of aircraft interior panels

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.; Leon, H. A.; Williamson, R. B.; Hasegawa, H.; Fisher, F.; Draemel, R.; Marcussen, W. H.; Hilado, C. J.

1976-01-01

The paper describes an experimental program carried out to evaluate a possible method for testing the fire-containment qualities of aircraft interior panels. The experimental apparatus consisted of a burner that simulates various fire loads under different ventilation conditions in an enclosure of approximately the same size as an aircraft lavatory module. Two fire-containment tests are discussed in which two adjoining walls of the enclosure were made from state-of-the-art composite panels; rats were exposed to the combustion products in order to evaluate the toxic threat posed by those products. The results show that the burner can be employed to represent various fire-load conditions and that the methodology developed for fire containment can be useful in evaluating the fire resistance of composite panels before conducting large-scale tests. It is concluded that elements of the fire-containment criteria include the temperature rise on the backface of the panels as a function of time, the flame burn-through by either decomposition or severe distortion of the material, and the toxicity of the combustion gases evolved.

Exterior building details of Building B, east façade: embedded wood ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior building details of Building B, east façade: embedded wood beams and interrupted dentil course cornice resulting from the removal of the third floor tuberculosis ward, yard level paneled Dutch door, second level two a typical six-light wood casement windows over a single-panel wood door with four light exits to fire escape; westerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Analysis of off-axis tension test of wood specimens

Treesearch

Jen Y. Liu

2002-01-01

This paper presents a stress analysis of the off-axis tension test of clear wood specimens based on orthotropic elasticity theory. The effects of Poisson's ratio and shear coupling coefficient on stress distribution are analyzed in detail. The analysis also provides a theoretical foundation for the selection of a 10° grain angle in wood specimens for the...

Improving the environmental profile of wood panels via co-production of ethanol and acetic acid.

PubMed

Earles, J Mason; Halog, Anthony; Shaler, Stephen

2011-11-15

The oriented strand board (OSB) biorefinery is an emerging technology that could improve the building, transportation, and chemical sectors' environmental profiles. By adding a hot water extraction stage to conventional OSB panel manufacturing, hemicellulose polysaccharides can be extracted from wood strands and converted to renewably sourced ethanol and acetic acid. Replacing fossil-based gasoline and acetic acid has the potential to reduce greenhouse gas (GHG) emissions, among other possible impacts. At the same time, hemicellulose extraction could improve the environmental profile of OSB panels by reducing the level of volatile organic compounds (VOCs) emitted during manufacturing. In this study, the life cycle significance of such GHG, VOC, and other emission reductions was investigated. A process model was developed based on a mix of laboratory and industrial-level mass and energy flow data. Using these data a life cycle assessment (LCA) model was built. Sensitive process parameters were identified and used to develop a target production scenario for the OSB biorefinery. The findings suggest that the OSB biorefinery's deployment could substantially improve human and ecosystem health via reduction of select VOCs compared to conventionally produced OSB, gasoline, and acetic acid. Technological advancements are needed, however, to achieve desirable GHG reductions.

Configuration and Sizing of a Test Fixture for Panels Under Combined Loads

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.

2006-01-01

Future air and space structures are expected to utilize composite panels that are subjected to combined mechanical loads, such as bi-axial compression/tension, shear and pressure. Therefore, the ability to accurately predict the buckling and strength failures of such panels is important. While computational analysis can provide tremendous insight into panel response, experimental results are necessary to verify predicted performances of these panels to judge the accuracy of computational methods. However, application of combined loads is an extremely difficult task due to the complex test fixtures and set-up required. Presented herein is a comparison of several test set-ups capable of testing panels under combined loads. Configurations compared include a D-box, a segmented cylinder and a single panel set-up. The study primarily focuses on the preliminary sizing of a single panel test configuration capable of testing flat panels under combined in-plane mechanical loads. This single panel set-up appears to be best suited to the testing of both strength critical and buckling critical panels. Required actuator loads and strokes are provided for various square, flat panels.

Propagating figured wood in black walnut

Treesearch

James R. McKenna; Wayne A. Geyer; Keith E. Woeste; Daniel L. Cassens

2015-01-01

Figured black walnut lumber is a specialty wood product that commands a high price for manufacturing fine furniture and interior paneling. Two common figured grain patterns occur in walnut; they are known as "fiddle-back" or "curly" grain, depending on the number of horizontal lines visible in the grain of the finished wood. The occurrence of...

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2003

Treesearch

David B. McKeever; Craig Adair; Jennifer O' Connor

2005-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only, because buildings with five or more stories are normally severely restricted by building code from...

Radiative, actively cooled panel tests results

NASA Technical Reports Server (NTRS)

Shore, C. P.; Nowak, R. J.; Sharpe, E. L.

1978-01-01

The radiative, actively cooled panel designed to withstand a uniform incident heat flux of 136 kW/sq m to a 444 K surface temperature was evaluated. The test program consisted of preliminary static thermal mechanical loading and aerothermal flow tests. Test results are briefly discussed.

Bond quality of phenol-based adhesives containing liquefied creosote-treated wood

Treesearch

Chung-Yun Hse; Feng Fu; Hui Pan

2009-01-01

Liquefaction of spent creosote-treated wood was studied to determine the technological practicability of its application in converting treated wood waste into resin adhesives. A total of 144 plywood panels were fabricated with experimental variables included 2 phenol to wood (P/W) ratios in liquefaction, 6 resin formulations (3 formaldehyde/liquefied wood (F/...

Mechanical properties of wood-based composite materials

Treesearch

Zhiyong Cai; Robert J. Ross

2010-01-01

The term composite is used to describe any wood material bonded together with adhesives. The current product mix ranges from fiberboard to laminated beams and components. In this chapter, wood-based composite materials are classified into the following categories: panel products (plywood, oriented strandboard (OSB), particleboard, fiberboard, medium-density fiberboard...

Syndromic Panel-Based Testing in Clinical Microbiology.

PubMed

Ramanan, Poornima; Bryson, Alexandra L; Binnicker, Matthew J; Pritt, Bobbi S; Patel, Robin

2018-01-01

The recent development of commercial panel-based molecular diagnostics for the rapid detection of pathogens in positive blood culture bottles, respiratory specimens, stool, and cerebrospinal fluid has resulted in a paradigm shift in clinical microbiology and clinical practice. This review focuses on U.S. Food and Drug Administration (FDA)-approved/cleared multiplex molecular panels with more than five targets designed to assist in the diagnosis of bloodstream, respiratory tract, gastrointestinal, or central nervous system infections. While these panel-based assays have the clear advantages of a rapid turnaround time and the detection of a large number of microorganisms and promise to improve health care, they present certain challenges, including cost and the definition of ideal test utilization strategies (i.e., optimal ordering) and test interpretation. Copyright © 2017 American Society for Microbiology.

Laboratory tests on fungal resistance of wood filled polyethylene composites

Treesearch

Craig M. Clemons; Rebecca E. Ibach

2002-01-01

A standard method for determining the durability of structural wood was modified for testing the fungal resistance of composites made from high density polyethylene filled with 50% wood flour. Moisture content, mechanical properties, and weight loss were measured over 12 weeks exposure to brown-and white-rot fungi. Mechanical properties were decreased, but irreversible...

Solar panel thermal cycling testing by solar simulation and infrared radiation methods

NASA Technical Reports Server (NTRS)

Nuss, H. E.

1980-01-01

For the solar panels of the European Space Agency (ESA) satellites OTS/MAROTS and ECS/MARECS the thermal cycling tests were performed by using solar simulation methods. The performance data of two different solar simulators used and the thermal test results are described. The solar simulation thermal cycling tests for the ECS/MARECS solar panels were carried out with the aid of a rotatable multipanel test rig by which simultaneous testing of three solar panels was possible. As an alternative thermal test method, the capability of an infrared radiation method was studied and infrared simulation tests for the ultralight panel and the INTELSAT 5 solar panels were performed. The setup and the characteristics of the infrared radiation unit using a quartz lamp array of approx. 15 sq and LN2-cooled shutter and the thermal test results are presented. The irradiation uniformity, the solar panel temperature distribution, temperature changing rates for both test methods are compared. Results indicate the infrared simulation is an effective solar panel thermal testing method.

Stress Testing of Organic Light- Emitting Diode Panels and Luminaires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Lynn; Rountree, Kelley; Mills, Karmann

This report builds on previous DOE efforts with OLED technology by updating information on a previously benchmarked OLED product (the Chalina luminaire from Acuity Brands) and provides new benchmarks on the performance of Brite 2 and Brite Amber OLED panels from OLEDWorks. During the tests described here, samples of these devices were subjected to continuous operation in stress tests at elevated ambient temperature environments of 35°C or 45°C. In addition, samples were also operated continuously at room temperature in a room temperature operational life test (RTOL). One goal of this study was to investigate whether these test conditions can acceleratemore » failure of OLED panels, either through panel shorting or an open circuit in the panel. These stress tests are shown to provide meaningful acceleration of OLED failure modes, and an acceleration factor of 2.6 was calculated at 45°C for some test conditions. In addition, changes in the photometric properties of the emitted light (e.g., luminous flux and chromaticity maintenance) was also evaluated for insights into the long-term stability of these products compared to earlier generations. Because OLEDs are a lighting system, electrical testing was also performed on the panel-driver pairs to provide insights into the impact of the driver on long-term panel performance.« less

From laboratory corrosion tests to a corrosion lifetime for wood fasteners : progress and challenges

Treesearch

Samuel L. Zelinka; Dominique Derome; Samuel V. Glass

2010-01-01

Determining a “corrosion-lifetime” for fasteners embedded in wood treated with recently adopted preservative systems depends upon successfully relating results of laboratory tests to in-service conditions. In contrast to laboratory tests where metal is embedded in wood at constant temperature and moisture content, the in-service temperature and moisture content of wood...

Asphalt and Wood Shingling. Roofing Workbook and Tests.

ERIC Educational Resources Information Center

Brown, Arthur

This combination workbook and set of tests contains materials on asphalt and wood shingling that have been designed to be used by those studying to enter the roofing and waterproofing trade. It consists of seven instructional units and seven accompanying objective tests. Covered in the individual units are the following topics: shingling…

Life testing of a nine-couple hybrid thermoelectric panel

NASA Technical Reports Server (NTRS)

Bifano, W. J.

1973-01-01

Life test data are presented for a nine couple thermoelectric panel of hybrid couples tested at an average hot junction temperature of 840 C (1113 K). In the hybrid couple, a hollow cylinder of p-type Si-Ge is used to encapsulate a segmented PbTe/Si-Ge n-leg. The output power and internal resistance of the panel as well as the resistances of the individual hybrid couples are presented as functions of test time covering a period of more than 4200 hours. Test results indicated improved stability relative to hybrid couples tested at higher temperatures. Thermal cycling of the panel resulted in an order of magnitude increase in room temperature resistance. However, very little change in resistance at operating temperatures was noted following the thermal cycles.

Preliminary study on flakeboard panels made from aspen slash wood

Treesearch

Yan Yu; Alan Rudie; Zhiyong Cai

2010-01-01

The disposal of forest-thinning residue is one of the major problems for sustainable forest management. The purpose of this study was to investigate the technical possibility of utilizing aspen logging slash wood with a diameter ranging from 50 to 76 mm for flakeboard production. Influences of weight ratio between slash wood and commercial flakes on the selected...

Manufacture, assembly, and delivery of beryllium test panels

NASA Technical Reports Server (NTRS)

1972-01-01

Details of the fabrication and assembly of two 99 cm by 99 cm (39 in. by 39 in.) beryllium heat shield test panels are presented. Each panel consists of two hat-stiffened, formed skins which overlap a transverse slip joint at the center of the panel; clips join the two skins at the slip joint, and continuous standoffs are provided at the ends of the panel. The hat-stiffeners are joined to the skin by furnace-brazing, using the braze alloy BAg 18. The parts are generally 0.051 cm (0.020 in.) thick. Tools used to form the detail parts are shown, together with the results of preliminary forming and brazing trials to verify processing techniques. Problems encountered in the manufacture of the panels are discussed.

Fire Resistance of Large-Scale Cross-Laminated Timber Panels

NASA Astrophysics Data System (ADS)

Henek, Vladan; Venkrbec, Václav; Novotný, Miloslav

2017-12-01

Wooden structures are increasingly being used in the construction of residential buildings. A common and often published reason to avoid wooden structures is their insufficient fire resistance, which reduces bearing capacity. For this reason, composite sandwich structures began to be designed to eliminate this drawback, as well as others. Recently, however, the trend is for a return to the original, wood-only variant and a search is underway for new technical means of improving the properties of such structures. Many timber structure technologies are known, but structures made from cross-laminated timber (CLT) panels have been used very often in recent years. CLT panels, also known as X-LAM, are currently gaining popularity in Europe. In the case of CLT panels composed of several layers of boards, they can be said to offer a certain advantage in that after the surface layer of a board has burnt and the subsurface layer has dried, oxygen is not drawn to the unburned wood for further combustion and thus the burning process ceases. CLT panels do not need to be specially modified or coated with fire resistant materials, although they are usually lined with gypsum-fibre fire resistant boards due to guidelines set out in the relevant standards. This paper presents a new method for the assessment of load-bearing perimeter walls fabricated from CLT panels without the use of an inner fire-retardant lining to ensure fire resistance at the level required by European standards (i.e. those harmonized for the Czech construction industry). The calculations were verified through laboratory tests which show that better parameters can be achieved during the classification of structures from the fire resistance point of view. The aim of the article is to utilize the results of assessment and testing by an accredited laboratory in order to demonstrate the possibilities of using CLT panels for the construction of multistorey as well as multi-purpose buildings in the Czech Republic.

Test fixture design for boron-aluminum and beryllium test panels

NASA Technical Reports Server (NTRS)

Breaux, C. G.

1973-01-01

A detailed description of the test fixture design and the backup analysis of the fixture assembly and its components are presented. The test fixture is required for the separate testing of two boron-aluminum and two beryllium compression panels. This report is presented in conjunction with a complete set of design drawings on the test fixture system.

Space Station Freedom solar array panels plasma interaction test facility

NASA Technical Reports Server (NTRS)

Martin, Donald F.; Mellott, Kenneth D.

1989-01-01

The Space Station Freedom Power System will make extensive use of photovoltaic (PV) power generation. The phase 1 power system consists of two PV power modules each capable of delivering 37.5 KW of conditioned power to the user. Each PV module consists of two solar arrays. Each solar array is made up of two solar blankets. Each solar blanket contains 82 PV panels. The PV power modules provide a 160 V nominal operating voltage. Previous research has shown that there are electrical interactions between a plasma environment and a photovoltaic power source. The interactions take two forms: parasitic current loss (occurs when the currect produced by the PV panel leaves at a high potential point and travels through the plasma to a lower potential point, effectively shorting that portion of the PV panel); and arcing (occurs when the PV panel electrically discharges into the plasma). The PV solar array panel plasma interaction test was conceived to evaluate the effects of these interactions on the Space Station Freedom type PV panels as well as to conduct further research. The test article consists of two active solar array panels in series. Each panel consists of two hundred 8 cm x 8 cm silicon solar cells. The test requirements dictated specifications in the following areas: plasma environment/plasma sheath; outgassing; thermal requirements; solar simulation; and data collection requirements.

Elevated-Temperature Tests Under Static and Aerodynamic Conditions on Honeycomb-Core Sandwich Panels

NASA Technical Reports Server (NTRS)

Groen, Joseph M.; Johnson, Aldie E., Jr.

1959-01-01

Stainless-steel honeycomb-core sandwich panels which differed primarily in skin thicknesses were tested at elevated temperatures under static and aerodynamic conditions. The results of these tests were evaluated to determine the insulating effectiveness and structural integrity of the panels. The static radiant-heating tests were performed in front of a quartz-tube radiant heater at panel skin temperatures up to 1,5000 F. The aerodynamic tests were made in a Mach 1.4 heated blowdown wind tunnel. The tunnel temperature was augmented by additional heat supplied by a radiant heater which raised the panel surface temperature above 8000 F during air flow. Static radiant-heating tests of 2 minutes duration showed that all the panels protected the load-carrying structure about equally well. Thin-skin panels showed an advantage for this short-time test over thick-skin panels from a standpoint of weight against insulation. Permanent inelastic strains in the form of local buckles over each cell of the honeycomb core caused an increase in surface roughness. During the aero- dynamic tests all of the panels survived with little or no damage, and panel flutter did not occur.

Transient Thermal Testing and Analysis of a Thermally Insulating Structural Sandwich Panel

NASA Technical Reports Server (NTRS)

Blosser, Max L.; Daryabeigi, Kamran; Bird, Richard K.; Knutson, Jeffrey R.

2015-01-01

A core configuration was devised for a thermally insulating structural sandwich panel. Two titanium prototype panels were constructed to illustrate the proposed sandwich panel geometry. The core of one of the titanium panels was filled with Saffil(trademark) alumina fibrous insulation and the panel was tested in a series of transient thermal tests. Finite element analysis was used to predict the thermal response of the panel using one- and two-dimensional models. Excellent agreement was obtained between predicted and measured temperature histories.

Cone calorimeter tests of wood composites

Treesearch

Robert H. White; Kuma Sumathipala

2013-01-01

The cone calorimeter is widely used for the determination of the heat release rate (HRR) of building products and other materials. As part of an effort to increase the availability of cone calorimeter data on wood products, the U.S. Forest Products Laboratory and the American Wood Council conducted this study on composite wood products in cooperation with the Composite...

Panel manipulation in social stress testing: The Bath Experimental Stress Test for Children (BEST-C).

PubMed

Cheetham, Tara J; Turner-Cobb, Julie M

2016-01-01

Whilst acute stress paradigms in adults make use of adult panel members, similar paradigms modified for child participants have not manipulated the panel. Most work has utilised an audience of adult confederates, regardless of the age of the population being tested. The aim of this study was to trial a social stress test for children that provided a meaningful environment using age-matched child peers as panel actors. Thirty-three participants (7-11 years) underwent the Bath Experimental Stress Test for Children (BEST-C). Based on the Trier Social Stress Test (TSST), it comprises a shortened six-minute public speaking task and four-minute maths challenge. It differs from previous stress tests by using age-matched children on the panel, pre-recorded and presented as a live feed, and includes an expanded manipulation check of subjective experience. Salivary cortisol was assessed at four time points, pre-post stress testing; life events, daily hassles and coping strategies were measured through questionnaires. A simple numerical coding scheme was applied to post-test interview data. The BEST-C generated a typical stress and adaptation response in salivary cortisol (p=.032). Age and gender differences were observed during recovery. Cortisol responses mapped directly onto three distinct subjective response patterns: (i) expected response and recovery; (ii) expected response, no recovery; (iii) no response. The BEST-C, utilising child confederates of participant target age is a meaningful social stress test for children. This is the first social stress test developed specifically for children that manipulates panel characteristics by using child confederates and a pre-recorded sham panel. Greater cortisol responses to the test were also found to match subjective verbal accounts of the experience. It offers a meaningful acute stress paradigm with potential applications to other child and adolescent age groups. Furthermore, it leads the way in the use of panel manipulation

Fabrication of low-cost Mod-OA wood composite wind turbine blades

NASA Technical Reports Server (NTRS)

Lark, R. F.; Gougeon, M.; Thomas, G.; Zuteck, M.

1983-01-01

The wood composite blades were fabricated by using epoxy resin-bonded laminates of Douglas fir veneers for the leading edge spar sections and honeycomb-cored birch plywood panels for the blade trailing edge or afterbody sections. The blade was joined to the wind turbine hub assembly by epoxy resin-bonded steel load take-off studs. The wood composite blades were installed in the Mod-OA wind turbine test facility at Kahuku, Hawaii. The wood composite blades have successfully completed high power (average of 150 kW) operations for an eighteen month period (nearly 8,000 hr) before replacement with another set of wood composite blades. The original set of blades was taken out of service because of the failure of the shank on one stud. An inspection of the blades at NASA-Lewis showed that the shank failure was caused by a high stress concentration at a corrosion pit on the shank fillet radius which resulted in fatigue stresses in excess of the endurance limit.

Nonlinear Analysis and Post-Test Correlation for a Curved PRSEUS Panel

NASA Technical Reports Server (NTRS)

Gould, Kevin; Lovejoy, Andrew E.; Jegley, Dawn; Neal, Albert L.; Linton, Kim, A.; Bergan, Andrew C.; Bakuckas, John G., Jr.

2013-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept, developed by The Boeing Company, has been extensively studied as part of the National Aeronautics and Space Administration's (NASA s) Environmentally Responsible Aviation (ERA) Program. The PRSEUS concept provides a light-weight alternative to aluminum or traditional composite design concepts and is applicable to traditional-shaped fuselage barrels and wings, as well as advanced configurations such as a hybrid wing body or truss braced wings. Therefore, NASA, the Federal Aviation Administration (FAA) and The Boeing Company partnered in an effort to assess the performance and damage arrestments capabilities of a PRSEUS concept panel using a full-scale curved panel in the FAA Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility. Testing was conducted in the FASTER facility by subjecting the panel to axial tension loads applied to the ends of the panel, internal pressure, and combined axial tension and internal pressure loadings. Additionally, reactive hoop loads were applied to the skin and frames of the panel along its edges. The panel successfully supported the required design loads in the pristine condition and with a severed stiffener. The panel also demonstrated that the PRSEUS concept could arrest the progression of damage including crack arrestment and crack turning. This paper presents the nonlinear post-test analysis and correlation with test results for the curved PRSEUS panel. It is shown that nonlinear analysis can accurately calculate the behavior of a PRSEUS panel under tension, pressure and combined loading conditions.

Low VOC drying of lumber and wood panel products. Progress report number 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hooda, U.; Banerjee, S.; Ingram, L.

1998-10-01

This project is based on the finding that brief microwave or RF-treatment of wood under low-headspace conditions leads to the release of VOCs. On occasion the authors have found that prolonged irradiation increases turpentine yield much more than anticipated from a simple mass balance; i.e., more pinene appeared to be released than was present in the wood in the first place. If taken at face value, this suggests that brief low-headspace irradiation removes VOCs, while prolonged exposure creates it. While seemingly improbable, this could follow if dielectric heating exposed regions of wood that were otherwise inaccessible to the solvent usedmore » for extraction (unlikely), or if the irradiation induced depolymerization of terpene dimers or higher polymers. In this report the authors attempt to identify the conditions that lead to this apparent enhancement of terpene yield, by constructing relationships between yield and irradiation parameters. The tentative conclusions are that this enhancement only occurs with relatively wet heartwood, and only under prolonged irradiation. An additional conclusion is that continuing analyses of twelve trees in the MSU forest confirm that the absence of a significant seasonal influence on turpentine content. An apparatus for permeability testing has been constructed, and work is underway.« less

Panel Board From Coconut Fibre And Pet Bottle

NASA Astrophysics Data System (ADS)

Ngadiman, Norhayati; Kaamin, Masiri; Abd. Kadir, Aslila; Sahat, Suhaila; Zaini, Aziza; Raihana Nor Zentan, Siti; Ain Ahmad, Nur; Amran, Wan Haizatul Aisyhah Wan

2018-03-01

The rate of global deforestation and its impact on the environment has led particle board manufacture to search for alternative feedstock, especially in countries where wood is less available compared to other cellulosic natural product. Based on the properties of coconut fibre and PET bottle, these two materials can be recycle as raw material for manufacture of panel board. As for this study, the coconut fibre were used as the filler and PET bottle as outer lining of the panel board. Two types of coconut fibre were used which are grinding and un-grinding coconut fibre. At first, the coconut fibre are undergoes softening, grinding, drying and sieving process, while PET bottle was cleaning, shredding, sieving before compacted using hydraulic hot press machine. There are four types of testing that been carried out which are swelling, water absorption, Modulus of Elasticity (MOE) and Modulus of Rupture (MOR). The result show the conventional board has the highest value for MOE test, so it's indicate that the conventional board is less strength from the coconut fibre board. As for water absorption test, the average water absorption of coconut fibre based panel board is less than conventional board. Overall, the coconut fibre board is better than conventional panel board because coconut fibre board are less swelling, has low water absorption, high modulus of rupture and low modulus of elasticity. Based on the finding, this coconut fibre panel board has potential as a stronger and long-lasting panel board than the conventional board in the market. Other than that, the panel also have their own aesthetic value since the recycled plastic bottle used as outer lining is colourful and giving aesthetic value.

The development of an Infrared Environmental System for TOPEX Solar Panel Testing

NASA Technical Reports Server (NTRS)

Noller, E.

1994-01-01

Environmental testing and flight qualification of the TOPEX/POSEIDON spacecraft solar panels were performed with infrared (IR) lamps and a control system that were newly designed and integrated. The basic goal was more rigorous testing of the costly panels' new composite-structure design without jeopardizing their safety. The technique greatly reduces the costs and high risks of testing flight solar panels.

Nondestructive Testing and Evaluation of Wood—50 Years of Research: International Nondestructive Testing and Evaluation of Wood Symposium Series

Treesearch

Robert J. Ross; Xiping Wang

2012-01-01

The International Nondestructive Testing and Evaluation of Wood Symposium Series was initiated by Washington State University and the USDA Forest Products Laboratory (FPL) in 1963 with the convening of a symposium on the topic of nondestructive testing of wood at FPL. Including that meeting, 17 symposia have been held during the last 50 years at various sites around...

CFD Simulations for Arc-Jet Panel Testing Capability Development Using Semi-Elliptical Nozzles

NASA Technical Reports Server (NTRS)

Gokcen, Tahir; Balboni, John A.; Hartman, G. Joseph

2016-01-01

This paper reports computational simulations in support of arc-jet panel testing capability development using semi-elliptical nozzles in a high enthalpy arc-jet facility at NASA Ames Research Center. Two different semi-elliptical nozzle configurations are proposed for testing panel test articles. Computational fluid dynamics simulations are performed to provide estimates of achievable panel surface conditions and useful test area for each configuration. The present analysis comprises three-dimensional simulations of the nonequilibrium flowfields in the semi-elliptical nozzles, test box and flowfield over the panel test articles. Computations show that useful test areas for the proposed two nozzle options are 20.32 centimeters by 20.32 centimeters (8 inches by 8 inches) and 43.18 centimeters by 43.18 centimeters (17 inches by 17 inches). Estimated values of the maximum cold-wall heat flux and surface pressure are 155 watts per centimeters squared and 39 kilopascals for the smaller panel test option, and 44 watts per centimeters squared and 7 kilopascals for the larger panel test option. Other important properties of the predicted flowfields are presented, and factors that limit the useful test area in the semi-free jet test configuration are discussed.

Substantiation Data for Advanced Beaded and Tubular Structural Panels. Volume 3: Testing

NASA Technical Reports Server (NTRS)

Hedges, P. C.; Greene, B. E.

1974-01-01

The test program is described, which was conducted to provide the necessary experimental data to verify the design and analysis methods developed for beaded and tubular panels. Test results are summarized and presented for all local buckling and full size panel tests. Selected representative test data from each of these tests is presented in detail. The results of this program established a valid analysis and design procedure for circular tube panels. Test results from three other configurations show deformational modes which are not adequately accounted for in the present analyses.

Variable Stiffness Panel Structural Analyses With Material Nonlinearity and Correlation With Tests

NASA Technical Reports Server (NTRS)

Wu, K. Chauncey; Gurdal, Zafer

2006-01-01

Results from structural analyses of three tow-placed AS4/977-3 composite panels with both geometric and material nonlinearities are presented. Two of the panels have variable stiffness layups where the fiber orientation angle varies as a continuous function of location on the panel planform. One variable stiffness panel has overlapping tow bands of varying thickness, while the other has a theoretically uniform thickness. The third panel has a conventional uniform-thickness [plus or minus 45](sub 5s) layup with straight fibers, providing a baseline for comparing the performance of the variable stiffness panels. Parametric finite element analyses including nonlinear material shear are first compared with material characterization test results for two orthotropic layups. This nonlinear material model is incorporated into structural analysis models of the variable stiffness and baseline panels with applied end shortenings. Measured geometric imperfections and mechanical prestresses, generated by forcing the variable stiffness panels from their cured anticlastic shapes into their flatter test configurations, are also modeled. Results of these structural analyses are then compared to the measured panel structural response. Good correlation is observed between the analysis results and displacement test data throughout deep postbuckling up to global failure, suggesting that nonlinear material behavior is an important component of the actual panel structural response.

Testing and analysis of flat and curved panels with multiple cracks

DOT National Transportation Integrated Search

1994-08-01

An experimental and analytical investigation of multiple cracking in various types of test specimens is described in this paper. The testing phase is comprised of a flat unstiffened panel series and curved stiffened and unstiffened panel series. The ...

Proceedings of the Symposium on Nondestructive Testing of Wood.

Treesearch

1964-01-01

This report summarizes the main points considered and the conclusions reached during the Symposium on Nondestructive Testing, October 7 to 9, 1963, at the Forest Products Laboratory. The purpose of this symposium was to bring research and industry leaders together to examine what is being done in nondestructive testing and discuss its applications to the wood products...

Testing and analysis of flat and curved panels with multiple cracks

NASA Technical Reports Server (NTRS)

Broek, David; Jeong, David Y.; Thomson, Douglas

1994-01-01

An experimental and analytical investigation of multiple cracking in various types of test specimens is described in this paper. The testing phase is comprised of a flat unstiffened panel series and curved stiffened and unstiffened panel series. The test specimens contained various configurations for initial damage. Static loading was applied to these specimens until ultimate failure, while loads and crack propagation were recorded. This data provides the basis for developing and validating methodologies for predicting linkup of multiple cracks, progression to failure, and overall residual strength. The results from twelve flat coupon and ten full scale curved panel tests are presented. In addition, an engineering analysis procedure was developed to predict multiple crack linkup. Reasonable agreement was found between predictions and actual test results for linkup and residual strength for both flat and curved panels. The results indicate that an engineering analysis approach has the potential to quantitatively assess the effect of multiple cracks in the arrest capability of an aircraft fuselage structure.

Composites from southern pine juvenile wood. Part 3. Juvenile and mature wood furnish mixtures

Treesearch

A.D. Pugel; E.W. Price; Chung-Yun Hse; T.F. Shupe

2004-01-01

Composite panelsmade from mixtures ofmature andjuvenile southern pine (Pinus taeda L.) were evaluated for initial mechanical properties and dimensional stability. The effect that the proportion of juvenile wood had on panel properties was analyzed by regression and rule-of-mixtures models. The mixed furnish data: 1) highlighted the degree to which...

Structural composite panel performance under long-term load

Treesearch

Theodore L. Laufenberg

1988-01-01

Information on the performance of wood-based structural composite panels under long-term load is currently needed to permit their use in engineered assemblies and systems. A broad assessment of the time-dependent properties of panels is critical for creating databases and models of the creep-rupture phenomenon that lead to reliability-based design procedures. This...

Long-Term Durability of Pressure-Treated Wood in a Severe Test Site

Treesearch

Stan Lebow; Bessie Woodward; Grant Kirker; Patricia Lebow

2013-01-01

Improved estimates of the long-term durability of treated wood products are needed to guide choices about construction materials and allow estimates of design life. This report summarizes the long-term decay and insect resistance of treated wood post and lumber specimens placed in ground contact at a test site of the U.S. Department of Agriculture, Forest Service,...

Panel Design Variations in the Multistage Test Using the Mixed-Format Tests

ERIC Educational Resources Information Center

Kim, Jiseon; Chung, Hyewon; Dodd, Barbara G.; Park, Ryoungsun

2012-01-01

This study compared various panel designs of the multistage test (MST) using mixed-format tests in the context of classification testing. Simulations varied the design of the first-stage module. The first stage was constructed according to three levels of test information functions (TIFs) with three different TIF centers. Additional computerized…

Testing painted wood : past practices at the Forest Products Laboratory and recommendations for future research

Treesearch

R. Sam Williams

2009-01-01

A brief history of paint research at the Forest Products Laboratory (FPL) in Madison, Wisconsin, sets the stage for a discussion of testing paint on wood and wood products. Tests include laboratory and outdoor tests, and I discuss them in terms of several degradation mechanisms (loss of gloss and fading, mildew growth, extractives bleed, and cracking, flaking, and...

Correlation Results for a Mass Loaded Vehicle Panel Test Article Finite Element Models and Modal Survey Tests

NASA Technical Reports Server (NTRS)

Maasha, Rumaasha; Towner, Robert L.

2012-01-01

High-fidelity Finite Element Models (FEMs) were developed to support a recent test program at Marshall Space Flight Center (MSFC). The FEMs correspond to test articles used for a series of acoustic tests. Modal survey tests were used to validate the FEMs for five acoustic tests (a bare panel and four different mass-loaded panel configurations). An additional modal survey test was performed on the empty test fixture (orthogrid panel mounting fixture, between the reverb and anechoic chambers). Modal survey tests were used to test-validate the dynamic characteristics of FEMs used for acoustic test excitation. Modal survey testing and subsequent model correlation has validated the natural frequencies and mode shapes of the FEMs. The modal survey test results provide a basis for the analysis models used for acoustic loading response test and analysis comparisons

Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

PubMed

Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

2015-12-01

The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome. Copyright © 2015 Elsevier Ltd. All rights reserved.

Full-Scale Testing and Analysis of Curved Aircraft Fuselage Panels.

DOT National Transportation Integrated Search

1993-12-01

The report presents data on (1) residual strength of aircraft panels containing Multiple-Site Damage (MSD) in lap splices, and (2) fatigue strength of panels subjected to cyclic pressure loading. The testing was conducted using the dedicated Aging Ai...

Wood crib fire free burning test in ISO room

NASA Astrophysics Data System (ADS)

Qiang, Xu; Griffin, Greg; Bradbury, Glenn; Dowling, Vince

2006-04-01

In the research of application potential of water mist fire suppression system for fire fighting in train luggage carriage, a series of experiments were conducted in ISO room on wood crib fire with and without water mist actuation. The results of free burn test without water mist suppression are used as reference in evaluating the efficiency of water mist suppression system. As part of the free burn test, several tests have been done under the hood of ISO room to calibrate the size of the crib fire and these tests can also be used in analyzing the wall effect in room fire hazard. In these free burning experiments, wood cribs of four sizes under the hood were tested. The temperature of crib fire, heat flux around the fire, gas concentration in hood of ISO room were measured in the experiments and two sets of thermal imaging system were used to get the temperature distribution and the typical shape of the free burning flames. From the experiments, the radiation intensity in specific positions around the fire, the effective heat of combustion, mass loss, oxygen consumption rate for different sizes of fire, typical structure of the flame and self extinguishment time was obtained for each crib size.

Flat panel display test and evaluation: procedures, standards, and facilities

NASA Astrophysics Data System (ADS)

Jackson, Timothy W.; Daniels, Reginald; Hopper, Darrel G.

1997-07-01

This paper addresses flat panel display test and evaluation via a discussion of procedures, standards and facilities. Procedures need to be carefully developed and documented to ensure that test accomplished in separate laboratories produce comparable results. The tests themselves must not be a source of inconsistency in test results when such comparisons are made in the course of procurements or new technology prototype evaluations. Standards are necessary to expedite the transition of the new display technologies into applications and to lower the costs of custom parts applied across disparate applications. The flat panel display industry is in the course of ascertaining and formulating such standards as they are of value to designers, manufacturers, marketers and users of civil and military products and equipment. Additionally, in order to inform the DoD and industry, the test and evaluation facilities of the Air Force Research Laboratory Displays Branch are described. These facilities are available to support procurements involving flat panel displays and to examine new technology prototypes. Finally, other government display testing facilities within the Navy and the Army are described.

Wood and Other Materials Used to Construct Nonresidential Buildings in the United States 2011

Treesearch

Craig Adair; David B. McKeever; Chris Gaston; Margaret Stewart

2013-01-01

The construction of low-rise nonresidential buildings is an important market for lumber, engineered wood products, and structural and nonstructural wood panels in the United States. This report examines low-rise nonresidential buildings of six or fewer stories. Those with more than six stories are normally severely restricted by building codes from being wood framed....

Evaluating wood-based composites for incipient fungal decay with the immunodiagnostic wood decay test.

Treesearch

C.A. Clausen; L. Haughton; C. Murphy

2003-01-01

Early and accurate detection of the extent of fungal deterioration during forensic inspection of the building envelope would eliminate excessive or unnecessary replacement of wood-based building materials. Areas of water infiltration in wood-framed building envelopes in the Pacific Northwest were evaluated visually and sampled for moisture content. Wood samples were...

Simulated hail impact testing of photovoltaic solar panels

NASA Technical Reports Server (NTRS)

Moore, D.; Wilson, A.; Ross, R.

1978-01-01

Techniques used to simulate and study the effect of hail on photovoltaic solar panels are described. Simulated hail stones (frozen ice spheres projected at terminal velocity) or steel balls were applied by air guns, gravity drop, or static loading. Tests with simulated hail and steel balls yielded different results. The impact strength of 10 commercially available flat-plate photovoltaic modules was tested. It was found that none of the six panel designs incorporating clear potting silicone material as the outermost layer remained undamaged by 1-in. simulated hailstones, while a photovoltaic module equipped with a 0.188-in.-thick acrylic cover sheet would be able to withstand the impact of a 2-in.-diameter hailstone.

Wood pellets, what else? Greenhouse gas parity times of European electricity from wood pellets produced in the south-eastern United States using different softwood feedstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanssen, Steef V.; Duden, Anna S.; Junginger, Martin

Several EU countries import wood pellets from the south-eastern United States. The imported wood pellets are (co-)fired in power plants with the aim of reducing overall greenhouse gas (GHG) emissions from electricity and meeting EU renewable energy targets. To assess whether GHG emissions are reduced and on what timescale, we construct the GHG balance of wood-pellet electricity. This GHG balance consists of supply chain and combustion GHG emissions, carbon sequestration during biomass growth, and avoided GHG emissions through replacing fossil electricity. We investigate wood pellets from four softwood feedstock types: small roundwood, commercial thinnings, harvest residues, and mill residues. Permore » feedstock, the GHG balance of wood-pellet electricity is compared against those of alternative scenarios. Alternative scenarios are combinations of alternative fates of the feedstock material, such as in-forest decomposition, or the production of paper or wood panels like oriented strand board (OSB). Alternative scenario composition depends on feedstock type and local demand for this feedstock. Results indicate that the GHG balance of wood-pellet electricity equals that of alternative scenarios within 0 to 21 years (the GHG parity time), after which wood-pellet electricity has sustained climate benefits. Parity times increase by a maximum of twelve years when varying key variables (emissions associated with paper and panels, soil carbon increase via feedstock decomposition, wood-pellet electricity supply chain emissions) within maximum plausible ranges. Using commercial thinnings, harvest residues or mill residues as feedstock leads to the shortest GHG parity times (0-6 years) and fastest GHG benefits from wood-pellet electricity. Here, we find shorter GHG parity times than previous studies, for we use a novel approach that differentiates feedstocks and considers alternative scenarios based on (combinations of) alternative feedstock fates, rather than on

Nonparametric estimation and testing of fixed effects panel data models

PubMed Central

Henderson, Daniel J.; Carroll, Raymond J.; Li, Qi

2009-01-01

In this paper we consider the problem of estimating nonparametric panel data models with fixed effects. We introduce an iterative nonparametric kernel estimator. We also extend the estimation method to the case of a semiparametric partially linear fixed effects model. To determine whether a parametric, semiparametric or nonparametric model is appropriate, we propose test statistics to test between the three alternatives in practice. We further propose a test statistic for testing the null hypothesis of random effects against fixed effects in a nonparametric panel data regression model. Simulations are used to examine the finite sample performance of the proposed estimators and the test statistics. PMID:19444335

Potential of chicken feather fibre in wood MDF composites

Treesearch

Jerold E. Winandy; James H. Muehl; Jessie A. Micales; Ashok Raina; Walter Schmidt

2003-01-01

We made a series of aspen fibre medium density fibreboard panels adding various levels of chicken feather fibre to determine the relative effect of the feather fibre-wood fibre mixtures on composite panel properties. Chicken feathers are a waste product left over after processing chickens for meat. The feather fibre amounts used ranged from 20% to 95% and a 5%...

LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

PubMed

Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

2015-04-01

Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Testing compression strength of wood logs by drilling resistance

NASA Astrophysics Data System (ADS)

Kalny, Gerda; Rados, Kristijan; Rauch, Hans Peter

2017-04-01

Soil bioengineering is a construction technique using biological components for hydraulic and civil engineering solutions, based on the application of living plants and other auxiliary materials including among others log wood. Considering the reliability of the construction it is important to know about the durability and the degradation process of the wooden logs to estimate and retain the integral performance of a soil bioengineering system. An important performance indicator is the compression strength, but this parameter is not easy to examine by non-destructive methods. The Rinntech Resistograph is an instrument to measure the drilling resistance by a 3 mm wide needle in a wooden log. It is a quasi-non-destructive method as the remaining hole has no weakening effects to the wood. This is an easy procedure but result in values, hard to interpret. To assign drilling resistance values to specific compression strengths, wooden specimens were tested in an experiment and analysed with the Resistograph. Afterwards compression tests were done at the same specimens. This should allow an easier interpretation of drilling resistance curves in future. For detailed analyses specimens were investigated by means of branch inclusions, cracks and distances between annual rings. Wood specimens are tested perpendicular to the grain. First results show a correlation between drilling resistance and compression strength by using the mean drilling resistance, average width of the annual rings and the mean range of the minima and maxima values as factors for the drilling resistance. The extended limit of proportionality, the offset yield strength and the maximum strength were taken as parameters for compression strength. Further investigations at a second point in time strengthen these results.

Properties of flat-pressed wood plastic composites containing fire retardants

Treesearch

Nadir Ayrilmis; Jan. T. Benthien; Heiko Thoemen; Robert H. White

2011-01-01

This study investigated physical, mechanical, and fire properties of the flat-pressed wood plastic composites (WPCs) incorporated with various fire retardants (FRs) [5 or 15% by weight (wt)] at 50 wt % of the wood flour (WF). The WPC panels were made from dry-blended WF, polypropylene (PP) with maleic anhydride grafted PP (2 wt %), and FR powder formulations using a...

Amplicon-Based Sequencing of Soil Fungi from Wood Preservative Test Sites

PubMed Central

Kirker, Grant T.; Bishell, Amy B.; Jusino, Michelle A.; Palmer, Jonathan M.; Hickey, William J.; Lindner, Daniel L.

2017-01-01

Soil samples were collected from field sites in two AWPA (American Wood Protection Association) wood decay hazard zones in North America. Two field plots at each site were exposed to differing preservative chemistries via in-ground installations of treated wood stakes for approximately 50 years. The purpose of this study is to characterize soil fungal species and to determine if long term exposure to various wood preservatives impacts soil fungal community composition. Soil fungal communities were compared using amplicon-based DNA sequencing of the internal transcribed spacer 1 (ITS1) region of the rDNA array. Data show that soil fungal community composition differs significantly between the two sites and that long-term exposure to different preservative chemistries is correlated with different species composition of soil fungi. However, chemical analyses using ICP-OES found levels of select residual preservative actives (copper, chromium and arsenic) to be similar to naturally occurring levels in unexposed areas. A list of indicator species was compiled for each treatment-site combination; functional guild analyses indicate that long-term exposure to wood preservatives may have both detrimental and stimulatory effects on soil fungal species composition. Fungi with demonstrated capacity to degrade industrial pollutants were found to be highly correlated with areas that experienced long-term exposure to preservative testing. PMID:29093702

Design, construction, and testing of the direct absorption receiver panel research experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavez, J.M.; Rush, E.E.; Matthews, C.W.

1990-01-01

A panel research experiment (PRE) was designed, built, and tested as a scaled-down model of a direct absorption receiver (DAR). The PRE is a 3-MW{sub t}DAR experiment that will allow flow testing with molten nitrate salt and provide a test bed for DAR testing with actual solar heating. In a solar central receiver system DAR, the heat absorbing fluid (a blackened molten nitrate salt) flows in a thin film down a vertical panel (rather than through tubes as in conventional receiver designs) and absorbs the concentrated solar flux directly. The ability of the flowing salt film to absorb flux directly.more » The ability of the flowing salt film to absorb the incident solar flux depends on the panel design, hydraulic and thermal fluid flow characteristics, and fluid blackener properties. Testing of the PRE is being conducted to demonstrate the engineering feasibility of the DAR concept. The DAR concept is being investigated because it offers numerous potential performance and economic advantages for production of electricity when compared to other solar receiver designs. The PRE utilized a 1-m wide by 6-m long absorber panel. The salt flow tests are being used to investigate component performance, panel deformations, and fluid stability. Salt flow testing has demonstrated that all the DAR components work as designed and that there are fluid stability issues that need to be addressed. Future solar testing will include steady-state and transient experiments, thermal loss measurements, responses to severe flux and temperature gradients and determination of peak flux capability, and optimized operation. In this paper, we describe the design, construction, and some preliminary flow test results of the Panel Research Experiment. 11 refs., 8 figs., 2 tabs.« less

Operation UPSHOT-KNOTHOLE, Nevada Proving Grounds, March-June 1953. Project 3.5 Tests on the Response of Wall and Roof Panels and the Transmission of Load to Supporting Structure

DTIC Science & Technology

1955-05-01

56 4.23 Postshot, 3.5ba, Interior of Test Cell . . . . . . . . • • 57 4.24 Postshot, 35.Sbb, Damage to Precast Concrete Channel Roof 6...Predicted Applied and Measured Transmitted Forces, Roof Panel 3.5bb (3-1/2 in. precast concrete channels on steel purlins) . . . o . o . ... . ... 104 5.16...truss rafters 3.Sba Bowstring truss with wood 4500 4200 10 7.1 10 decking, tar and gravel roofing 3.5bb 3-1/2 in. precast concrete channels on steel

A swept wing panel in a low speed flexible walled test section

NASA Technical Reports Server (NTRS)

Goodyer, M. J.

1987-01-01

The testing of two-dimensional airfoil sections in adaptive wall tunnels is relatively widespread and has become routine at all speeds up to transonic. In contrast, the experience with the three-dimensional testing of swept panels in adaptive wall test sections is very limited, except for some activity in the 1940's at NPL, London. The current interest in testing swept wing panels led to the work covered by this report, which describes the design of an adaptive-wall swept-wing test section for a low speed wind tunnel and gives test results for a wing panel swept at 40 deg. The test section has rigid flat sidewalls supporting the panel, and features flexible top and bottom wall with ribs swept at the same angle as the wing. When streamlined, the walls form waves swept at the same angle as the wing. The C sub L (-) curve for the swept wing, determined from its pressure distributions taken with the walls streamlined, compare well with reference data which was taken on the same model, unswept, in a test section deep enough to avoid wall interference.

Review of test methods used to determine the corrosion rate of metals in contact with treated wood

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2005-01-01

The purpose of this literature review is to give an overview of test methods previously used to evaluate the corrosion of metals in contact with wood. This article reviews the test methods used to evaluate the corrosion of metals in contact with wood by breaking the experiments into three groups: exposure tests, accelerated exposure tests, and electrochemical tests....

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

PubMed

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

Capacity, production, and manufacture of woodbased panels in the United States and Canada

Treesearch

Henry Spelter

1996-01-01

Structural and nonstructural panel products have constituted the fastest growing segment of the wood products industries over the past two decades. Based on announced plans, growth will accelerate in the next 2 years. The cost of wood fiber used in these processes has been rising. To keep wood costs as low as possible, a growing share of the new production is being...

Modeling Force Transfer around Openings in Wood-Frame Shear Walls

Treesearch

Minghao Li; Frank Lam; Borjen Yeh; Tom Skaggs; Doug Rammer; James Wacker

2012-01-01

This paper presented a modeling study on force transfer around openings (FTAO) in wood-frame shear walls detailed for FTAO. To understand the load transfer in the walls, this study used a finite-element model WALL2D, which is able to model individual wall components, including framing members, sheathing panels, oriented panel-frame nailed connections, framing...

Future carbon storage in harvested wood products from Ontario's Crown forests

Treesearch

Jiaxin Chen; Stephen J. Colombo; Michael T. Ter-Mikaelian; Linda S. Heath

2008-01-01

This analysis quantifies projected carbon (C) storage in harvested wood products (HWP) from Ontario's Crown forests. The large-scale forest C budget model, FORCARB-ON, was applied to estimate HWP C stock changes using the production approach defined by the Intergovernmental Panel on Climate Change. Harvested wood volume was converted to C mass and allocated to...

Fatigue testing of wood-concrete composite beams.

DOT National Transportation Integrated Search

2013-05-01

Currently, wood-concrete composite structural members are usually applied in building structures. There are a relatively small number (in the low 100s) of known bridge applications involving wood-concrete composites. A problem with using these novel ...

Inward Leakage Variability between Respirator Fit Test Panels – Part I. Deterministic Approach

PubMed Central

Zhuang, Ziqing; Liu, Yuewei; Coffey, Christopher C.; Miller, Colleen; Szalajda, Jonathan

2015-01-01

Inter-panel variability has never been investigated. The objective of this study was to determine the variability between different anthropometric panels used to determine the inward leakage (IL) of N95 filtering facepiece respirators (FFRs) and elastomeric half-mask respirators (EHRs). A total of 144 subjects, who were both experienced and non-experienced N95 FFR users, were recruited. Five N95 FFRs and five N95 EHRs were randomly selected from among those models tested previously in our laboratory. The PortaCount Pro+ (without N95-Companion) was used to measure IL of the ambient particles with a detectable size range of 0.02 to 1 μm. The Occupational Safety and Health Administration standard fit test exercises were used for this study. IL test were performed for each subject using each of the 10 respirators. Each respirator/subject combination was tested in duplicate, resulting in a total 20 IL tests for each subject. Three 35-member panels were randomly selected without replacement from the 144 study subjects stratified by the National Institute for Occupational Safety and Health bivariate panel cell for conducting statistical analyses. The geometric mean (GM) IL values for all 10 studied respirators were not significantly different among the three randomly selected 35-member panels. Passing rate was not significantly different among the three panels for all respirators combined or by each model. This was true for all IL pass/fail levels of 1%, 2%, and 5%. Using 26 or more subjects to pass the IL test, all three panels had consistent passing/failing results for pass/fail levels of 1% and 5%. Some disagreement was observed for the 2% pass/fail level. Inter-panel variability exists, but it is small relative to the other sources of variation in fit testing data. The concern about inter-panel variability and other types of variability can be alleviated by properly selecting: pass/fail level (IL 1–5%); panel size (e.g., 25 or 35); and minimum number of subjects

85. INTERIOR VIEW, DETAIL, HEAD HOUSE, FIRST FLOOR AMBULATORY, WOOD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

85. INTERIOR VIEW, DETAIL, HEAD HOUSE, FIRST FLOOR AMBULATORY, WOOD FLOOR SHOWING ORIGINAL AND REPLACED PANELS, LOOKING SOUTHWEST - Timberline Lodge, Timberline Trail, Government Camp, Clackamas County, OR

Tank testing of a 2500-cm2 solar panel

NASA Technical Reports Server (NTRS)

Bever, R. S.; Staskus, J.

1981-01-01

A 50 cm by 50 cm solar array panel test patch was investigated for spacecraft charging and arcing effects. Bombardment with monochromatic electron was carried out. Some objectives of the test were: (1) to estimate at what voltage of electron bombardment arcing would be probable; (2) to find whether the arc's energy would be tolerable or damagingly large; (3) to try and separate thermal and photoeffects; and, (4) to see whether materials used were such as to minimize arcing. Some conclusions were: In sunlight the tracking data relay satellite's solar panel which has ceria glass on the front and conductive paint on the backside is probably a good design for reducing charge-up. In a geomagnetic substorm simulated in testing there will be arcing at the interconnects during eclipse and transitions into and out of eclipse in testing especially in view of the very cold temperatures that will be reached by this lightweight array. Ceria-doped glass is preferred to fused silica glass for reducing charge build up. The Kapton bare patch should still be conductively painted. The differential voltages on the panel determine when arcing first begins, and the electron beam voltages vary depending upon whether the metallic structure is directly grounded or semifloating.

Accelerated weathering of fire-retardant-treated wood for fire testing

Treesearch

Robert H. White

2009-01-01

Fire-retardant-treated products for exterior applications must be subjected to actual or accelerated weathering prior to fire testing. For fire-retardant-treated wood, the two accelerated weathering methods have been Method A and B of ASTM D 2898. The rain test is Method A of ASTM D 2898. Method B includes exposures to ultraviolet (UV) sunlamps in addition to water...

Traps and attractants for wood-boring insects in ponderosa pine stands in the Black Hills, South Dakota.

PubMed

Costello, Sheryl L; Negrón, José F; Jacobi, William R

2008-04-01

Recent large-scale wildfires have increased populations of wood-boring insects in the Black Hills of South Dakota. Because little is known about possible impacts of wood-boring insects in the Black Hills, land managers are interested in developing monitoring techniques such as flight trapping with semiochemical baits. Two trap designs and four semiochemical attractants were tested in a recently burned ponderosa pine, Pinus ponderosa Dougl. ex Laws., forest in the Black Hills. Modified panel and funnel traps were tested in combination with the attractants, which included a woodborer standard (ethanol and alpha-pinene), standard plus 3-carene, standard plus ipsenol, and standard plus ipsdienol. We found that funnel traps were equally efficient or more efficient in capturing wood-boring insects than modified panel traps. Trap catches of cerambycids increased when we added the Ips spp. pheromone components (ipsenol or ipsdienol) or the host monoterpene (3-carene) to the woodborer standard. During the summers of 2003 and 2004, 18 cerambycid, 14 buprestid, and five siricid species were collected. One species of cerambycid, Monochamus clamator (LeConte), composed 49 and 40% of the 2003 and 2004 trap catches, respectively. Two other cerambycids, Acanthocinus obliquus (LeConte) and Acmaeops proteus (Kirby), also were frequently collected. Flight trap data indicated that some species were present throughout the summer, whereas others were caught only at the beginning or end of the summer.

Initial Results of Multigene Panel Testing for Hereditary Breast and Ovarian Cancer and Lynch Syndrome.

PubMed

Howarth, Dt R; Lum, Sharon S; Esquivel, Pamela; Garberoglio, Carlos A; Senthil, Maheswari; Solomon, Naveenraj L

2015-10-01

Multigene panel testing for hereditary cancer risk has recently become commercially available; however, the impact of its use on patient care is undefined. We sought to evaluate results from implementation of panel testing in a multidisciplinary cancer center. We performed a retrospective review of consecutive patients undergoing genetic testing after initiating use of multigene panel testing at Loma Linda University Medical Center. From February 13 to August 25, 2014, 92 patients were referred for genetic testing based on National Comprehensive Cancer Network guidelines. Testing was completed in 90 patients. Overall, nine (10%) pathogenic mutations were identified: five BRCA1/2, and four in non-BRCA loci. Single-site testing identified one BRCA1 and one BRCA2 mutation. The remaining mutations were identified by use of panel testing for hereditary breast and ovarian cancer. There were 40 variants of uncertain significance identified in 34 patients. The use of panel testing more than doubled the identification rate of clinically significant pathogenic mutations that would have been missed with BRCA testing alone. The large number of variants of uncertain significance identified will require long-term follow-up for potential reclassification. Multigene panel testing provides additional information that may improve patient outcomes.

Wood biodegradation in laboratory-scale landfills.

PubMed

Wang, Xiaoming; Padgett, Jennifer M; De la Cruz, Florentino B; Barlaz, Morton A

2011-08-15

The objective of this research was to characterize the anaerobic biodegradability of major wood products in municipal waste by measuring methane yields, decay rates, the extent of carbohydrate decomposition, carbon storage, and leachate toxicity. Tests were conducted in triplicate 8 L reactors operated to obtain maximum yields. Measured methane yields for red oak, eucalyptus, spruce, radiata pine, plywood (PW), oriented strand board (OSB) from hardwood (HW) and softwood (SW), particleboard (PB) and medium-density fiberboard (MDF) were 32.5, 0, 7.5, 0.5, 6.3, 84.5, 0, 5.6, and 4.6 mL CH(4) dry g(-1), respectively. The red oak, a HW, exhibited greater decomposition than either SW (spruce and radiata), a trend that was also measured for the OSB-HW relative to OSB-SW. However, the eucalyptus (HW) exhibited toxicity. Thus, wood species have unique methane yields that should be considered in the development of national inventories of methane production and carbon storage. The current assumption of uniform biodegradability is not appropriate. The ammonia release from urea formaldehyde as present in PB and MDF could contribute to ammonia in landfill leachate. Using the extent of carbon conversion measured in this research, 0-19.9%, predicted methane production from a wood mixture using the Intergovernmental Panel for Climate Change waste model is only 7.9% of that predicted using the 50% carbon conversion default.

Reaction-to-fire testing and modeling for wood products

Treesearch

Mark A. Dietenberger; Robert H. White

2001-01-01

In this review we primarily discuss our use of the oxygen consumption calorimeter (ASTM E1354 for cone calorimeter and ISO9705 for room/corner tests) and fire growth modeling to evaluate treated wood products. With recent development towards performance-based building codes, new methodology requires engineering calculations of various fire growth scenarios. The initial...

Performance of different SNP panels for parentage testing in two East Asian cattle breeds.

PubMed

Strucken, E M; Gudex, B; Ferdosi, M H; Lee, H K; Song, K D; Gibson, J P; Kelly, M; Piper, E K; Porto-Neto, L R; Lee, S H; Gondro, C

2014-08-01

The International Society for Animal Genetics (ISAG) proposed a panel of single nucleotide polymorphisms (SNPs) for parentage testing in cattle (a core panel of 100 SNPs and an additional list of 100 SNPs). However, markers specific to East Asian taurine cattle breeds were not included, and no information is available as to whether the ISAG panel performs adequately for these breeds. We tested ISAG's core (100 SNP) and full (200 SNP) panels on two East Asian taurine breeds: the Korean Hanwoo and the Japanese Wagyu, the latter from the Australian herd. Even though the power of exclusion was high at 0.99 for both ISAG panels, the core panel performed poorly with 3.01% false-positive assignments in the Hanwoo population and 3.57% in the Wagyu. The full ISAG panel identified all sire-offspring relations correctly in both populations with 0.02% of relations wrongly excluded in the Hanwoo population. Based on these results, we created and tested two population-specific marker panels: one for the Wagyu population, which showed no false-positive assignments with either 100 or 200 SNPs, and a second panel for the Hanwoo, which still had some false-positive assignments with 100 SNPs but no false positives using 200 SNPs. In conclusion, for parentage assignment in East Asian cattle breeds, only the full ISAG panel is adequate for parentage testing. If fewer markers should be used, it is advisable to use population-specific markers rather than the ISAG panel. © 2014 Stichting International Foundation for Animal Genetics.

New method for rapid testing of bond strength for wood adhesives

Treesearch

James M. Wescott; Michael J. Birkeland; Amy E. Traska; Charles R. Frihart; Brice N. Dally

2007-01-01

In developing new adhesives for wood bonding, the testing of bond performance can often be a limiting factor in the development process. Evaluating the bond performance of an adhesive that can be prepared in less than a day often takes several days using standard performance tests. This testing slows the development process and may cause a company to abandon a...

Kickback risk of portable chainsaws while cutting wood of different properties: laboratory tests and deductions

PubMed Central

Dąbrowski, Andrzej

2015-01-01

Portable chainsaws are associated with substantial risk and can cause serious injury to operators, especially during kickback. This paper presents new results from research and analyses conducted regarding the impact between the different properties of wood on this occurrence. In an open area, such differences may include: wood species, humidity, temperature and the facing angle of the wood fibres in relation to the kerf and shape of the wood surface that comes in contact with the tip of the guide bar. This paper investigates chainsaw kickback including the research results on kickback and wood-cutting energy, saw chain speed and the efficiency of the chainsaw engine. It also presents conclusions drawn from the tests that can be useful for chainsaw users, showing the dependencies between the different properties of wood and the risk of injury. PMID:26694003

Wood and Other Materials Used to Construct Nonresidential Buildings in the United States 2011 Executive Summary

Treesearch

David B. McKeever

2013-01-01

The construction of low-rise nonresidential buildings is an important market for lumber, engineered wood products, and structural and nonstructural wood panels in the United States. This report examines low-rise nonresidential buildings of six or fewer stories. Those with more than six stories are normally severely restricted by building codes from being wood framed....

AXAF-I Low Intensity-Low Temperature (LILT) Testing of the Development Verification Test (DVT) Solar Panel

NASA Technical Reports Server (NTRS)

Alexander, Doug; Edge, Ted; Willowby, Doug

1998-01-01

The planned orbit of the AXAF-I spacecraft will subject the spacecraft to both short, less than 30 minutes for solar and less than 2 hours for lunar, and long earth eclipses and lunar eclipses with combined conjunctive duration of up to 3 to 4 hours. Lack of proper Electrical Power System (EPS) conditioning prior to eclipse may cause loss of mission. To avoid this problem, for short eclipses, it is necessary to off-point the solar array prior to or at the beginning of the eclipse to reduce the battery state of charge (SOC). This yields less overcharge during the high charge currents at sun entry. For long lunar eclipses, solar array pointing and load scheduling must be tailored for the profile of the eclipse. The battery SOC, loads, and solar array current-voltage (I-V) must be known or predictable to maintain the bus voltage within acceptable range. To address engineering concerns about the electrical performance of the AXAF-I solar array under Low Intensity and Low Temperature (LILT) conditions, Marshall Space Flight Center (MSFC) engineers undertook special testing of the AXAF-I Development Verification Test (DVT) solar panel in September-November 1997. In the test the DVT test panel was installed in a thermal vacuum chamber with a large view window with a mechanical "flapper door". The DVT test panel was "flash" tested with a Large Area Pulse Solar Simulator (LAPSS) at various fractional sun intensities and panel (solar cell) temperatures. The testing was unique with regards to the large size of the test article and type of testing performed. The test setup, results, and lessons learned from the testing will be presented.

Concentrating Solar Power Central Receiver Panel Component Fabrication and Testing FINAL REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDowell, Michael W; Miner, Kris

The objective of this project is to complete a design of an advanced concentrated solar panel and demonstrate the manufacturability of key components. Then confirm the operation of the key components under prototypic solar flux conditions. This work is an important step in reducing the levelized cost of energy (LCOE) from a central receiver solar power plant. The key technical risk to building larger power towers is building the larger receiver systems. Therefore, this proposed technology project includes the design of an advanced molten salt prototypic sub-scale receiver panel that can be utilized into a large receiver system. Then completemore » the fabrication and testing of key components of the receive design that will be used to validate the design. This project shall have a significant impact on solar thermal power plant design. Receiver panels of suitable size for utility scale plants are a key element to a solar power tower plant. Many subtle and complex manufacturing processes are involved in producing a reliable, robust receiver panel. Given the substantial size difference between receiver panels manufactured in the past and those needed for large plant designs, the manufacture and demonstration on prototype receiver panel components with representative features of a full-sized panel will be important to improving the build process for commercial success. Given the thermal flux limitations of the test facility, the panel components cannot be rendered full size. Significance changes occurred in the projects technical strategies from project initiation to the accomplishments described herein. The initial strategy was to define cost improvements for the receiver, design and build a scale prototype receiver and test, on sun, with a molten salt heat transport system. DOE had committed to constructing a molten salt heat transport loop to support receiver testing at the top of the NSTTF tower. Because of funding constraints this did not happen. A subsequent

Experimental Results From Stitched Composite Multi-Bay Fuselage Panels Tested Under Uni-Axial Compression

NASA Technical Reports Server (NTRS)

Baker, Donald J.

2004-01-01

The experimental results from two stitched VARTM composite panels tested under uni-axial compression loading are presented. The curved panels are divided by frames and stringers into five or six bays with a column of three bays along the compressive loading direction. The frames are supported at the ends to resist out-of-plane translation. Back-to-back strain gages are used to record the strain and displacement transducers were used to record the out-of-plane displacements. In addition a full-field measurement technique that utilizes a camera-based-stero-vision system was used to record displacements. The panels were loaded in increments to determine the first bay to buckle. Loading was discontinued at limit load and the panels were removed from the test machine for impact testing. After impacting at 20 ft-lbs to 25 ft-lbs of energy with a spherical indenter, the panels were loaded in compression until failure. Impact testing reduced the axial stiffness 4 percent and less than 1 percent. Postbuckled axial panel stiffness was 52 percent and 70 percent of the pre-buckled stiffness.

Low frequency noise as a control test for spacial solar panels

NASA Astrophysics Data System (ADS)

Orsal, B.; Alabedra, R.; Ruas, R.

1986-07-01

The present study of low frequency noise in a forward-biased dark solar cell, in order to develop an NDE test method for solar panels, notes that a single cell with a given defect is thus detectable under dark conditions. The test subject was a space solar panel consisting of five cells in parallel and five in series; these cells are of the n(+)-p monocrystalline Si junction type. It is demonstrated that the noise associated with the defective cell is 10-15 times higher than that of a good cell. Replacement of a good cell by a defective one leads to a 30-percent increase in the noise level of the panel as a whole.

Babes in the Woods: The Wanderings of the National Reading Panel.

ERIC Educational Resources Information Center

Yatvin, Joanne

2002-01-01

Former member of the National Reading Panel criticizes the composition, deliberations, and decisions of the panel, authorized by Congress in 1997, leading to its April 2000 report supporting the hierarchy-of-skills reading model. (PKP)

Tuned Chamber Core Panel Acoustic Test Results

NASA Technical Reports Server (NTRS)

Schiller, Noah H.; Allen, Albert R.

2016-01-01

This report documents acoustic testing of tuned chamber core panels, which can be used to supplement the low-frequency performance of conventional acoustic treatment. The tuned chamber core concept incorporates low-frequency noise control directly within the primary structure and is applicable to sandwich constructions with a directional core, including corrugated-, truss-, and fluted-core designs. These types of sandwich structures have long, hollow channels (or chambers) in the core. By adding small holes through one of the facesheets, the hollow chambers can be utilized as an array of low-frequency acoustic resonators. These resonators can then be used to attenuate low-frequency noise (below 400 Hz) inside a vehicle compartment without increasing the weight or size of the structure. The results of this test program demonstrate that the tuned chamber core concept is effective when used in isolation or combined with acoustic foam treatments. Specifically, an array of acoustic resonators integrated within the core of the panels was shown to improve both the low-frequency absorption and transmission loss of the structure in targeted one-third octave bands.

Proceedings: 19th International Nondestructive Testing and Evaluation of Wood Symposium

Treesearch

Robert J. Ross; Raquel Gonçalves; Xiping Wang

2015-01-01

The 19th International Nondestructive Testing and Evaluation of Wood Symposium was hosted by the University of Campinas, College of Agricultural Engineering (FEAGRI/UNICAMP), and the Brazilian Association of Nondestructive Testing and Evaluation (ABENDI) in Rio de Janeiro, Brazil, on September 22–25, 2015. This Symposium was a forum for those involved in nondestructive...

Cooled Ceramic Composite Panel Tested Successfully in Rocket Combustion Facility

NASA Technical Reports Server (NTRS)

Jaskowiak, Martha H.

2003-01-01

Regeneratively cooled ceramic matrix composite (CMC) structures are being considered for use along the walls of the hot-flow paths of rocket-based or turbine-based combined-cycle propulsion systems. They offer the combined benefits of substantial weight savings, higher operating temperatures, and reduced coolant requirements in comparison to components designed with traditional metals. These cooled structures, which use the fuel as the coolant, require materials that can survive aggressive thermal, mechanical, acoustic, and aerodynamic loads while acting as heat exchangers, which can improve the efficiency of the engine. A team effort between the NASA Glenn Research Center, the NASA Marshall Space Flight Center, and various industrial partners has led to the design, development, and fabrication of several types of regeneratively cooled panels. The concepts for these panels range from ultra-lightweight designs that rely only on CMC tubes for coolant containment to more maintainable designs that incorporate metal coolant containment tubes to allow for the rapid assembly or disassembly of the heat exchanger. One of the cooled panels based on an all-CMC design was successfully tested in the rocket combustion facility at Glenn. Testing of the remaining four panels is underway.

Effects of Cancer Genetic Panel Testing on at-Risk Individuals.

PubMed

Frost, Anja S; Toaff, Miriam; Biagi, Tara; Stark, Elizabeth; McHenry, Allison; Kaltman, Rebecca

2018-06-01

To evaluate the role of screening patients at increased risk for hereditary cancer syndromes with an extended panel of cancer predisposition genes to identify actionable genetic mutations. A retrospective chart review was conducted of all patients presenting to a multidisciplinary cancer program for genetic counseling and testing from January 2015 to December 2016. Individuals presenting to the program were identified as at-risk by a personal or family history of cancer, by their health care provider, or by self-referral. All participants met current National Comprehensive Cancer Network criteria for genetic risk evaluation for hereditary cancer. The results of testing and its implications for management, based on National Comprehensive Cancer Network guidelines, were recorded. Of 670 at-risk patients who underwent genetic testing, 66 (9.9%) had BRCA-limited testing; of these, 26 of 670 (3.9%) had a deleterious or likely pathogenic mutation. Expanded panel testing was done for 560 of the 670 patients (83.4%), and abnormal results were found in 65 of 670 (9.7%); non-BRCA mutations (predominantly CHEK2) were found in 49 of the 65 (75%). Abnormal genetic testing was associated with increased surveillance in 96% of those with deleterious mutations, whereas negative testing for a known familial mutation in 45 patients was associated with a downgrade of their risk and reduction of subsequent surveillance and management. Guideline-based management is frequently altered by genetic testing, including panel testing, in patients at risk for cancer. We recommend that obstetrics and gynecology providers routinely refer at-risk patients for genetic counseling and testing when clinically appropriate.

24 CFR 3280.406 - Air chamber test method for certification and qualification of formaldehyde emission levels.

Code of Federal Regulations, 2010 CFR

2010-04-01

... particleboard is produced or surface-finished, whichever is later, the panels must be dead-stacked or air-tight... with the Standard Test Method for Determining Formaldehyde Levels from Wood Products Under Defined Test...

Comparison of Wood Preservatives in Stake Tests (1981 Progress Report).

DTIC Science & Technology

1981-12-01

infected with Trichoderma mold, plus other selected species such as oak, Douglas-fir, and Engelmann spruce. Southern pine untreated control stakes...acetylated wood, cyanoethylated wood, that with thiamine destroyed, chemically modified wood, wood infected with Trichoderma mold, embedded fiberboard (western...14 toA4 41U(4 a ...- 44- Table 31.--Condition of southern pine stakes (2 x 4 in. nominal x 18 in.) of uninfected and Trichoderma mcid-infected wood

17. Building 202, observation room for test cell, showing panel, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. Building 202, observation room for test cell, showing panel, abort button, phones, and observation window. View looking northwest. - Rocket Engine Testing Facility, GRC Building No. 202, NASA Glenn Research Center, Cleveland, Cuyahoga County, OH

Wood fuel consumption and mortality rates in Sub-Saharan Africa: Evidence from a dynamic panel study.

PubMed

Sulaiman, Chindo; Abdul-Rahim, A S; Chin, Lee; Mohd-Shahwahid, H O

2017-06-01

This study examined the impact of wood fuel consumption on health outcomes, specifically under-five and adult mortality in Sub-Saharan Africa, where wood usage for cooking and heating is on the increase. Generalized method of moment (GMM) estimators were used to estimate the impact of wood fuel consumption on under-five and adult mortality (and also male and female mortality) in the region. The findings revealed that wood fuel consumption had significant positive impact on under-five and adult mortality. It suggests that over the studied period, an increase in wood fuel consumption has increased the mortality of under-five and adult. Importantly, it indicated that the magnitude of the effect of wood fuel consumption was more on the under-five than the adults. Similarly, assessing the effect on a gender basis, it was revealed that the effect was more on female than male adults. This finding suggests that the resultant mortality from wood smoke related infections is more on under-five children than adults, and also are more on female adults than male adults. We, therefore, recommended that an alternative affordable, clean energy source for cooking and heating should be provided to reduce the wood fuel consumption. Copyright © 2017 Elsevier Ltd. All rights reserved.

Plans for crash-tested wood bridge railings for concrete decks

Treesearch

Michael A. Ritter; Ronald K. Faller; Barry T. Rosson; Paula D. Hilbrich Lee; Sheila Rimal Duwadi

1998-01-01

As part of a continuing cooperative research between the Midwest Roadside Safety Facility (MwRSF); the USDA Forest Service, Forest Products Laboratory (FPL); and the Federal Highway Administration (FHWA), several crashworthy wood bridge railings and approach railing transitions have been adapted for use on concrete bridge decks. These railings meet testing and...

At-line validation of a process analytical technology approach for quality control of melamine-urea-formaldehyde resin in composite wood-panel production using near infrared spectroscopy.

PubMed

Meder, Roger; Stahl, Wolfgang; Warburton, Paul; Woolley, Sam; Earnshaw, Scott; Haselhofer, Klaus; van Langenberg, Ken; Ebdon, Nick; Mulder, Roger

2017-01-01

The reactivity of melamine-urea-formaldehyde resins is of key importance in the manufacture of engineered wood products such as medium density fibreboard (MDF) and other wood composite products. Often the MDF manufacturing plant has little available information on the resin reactivity other than details of the resin specification at the time of batch manufacture, which often occurs off-site at a third-party resin plant. Often too, fresh resin on delivery at the MDF plant is mixed with variable volume of aged resin in storage tanks, thereby rendering any specification of the fresh resin batch obsolete. It is therefore highly desirable to develop a real-time, at-line or on-line, process analytical technology to monitor the quality of the resin prior to MDF panel manufacture. Near infrared (NIR) spectroscopy has been calibrated against standard quality methods and against 13 C nuclear magnetic resonance (NMR) measures of molecular composition in order to provide at-line process analytical technology (PAT), to monitor the resin quality, particularly the formaldehyde content of the resin. At-line determination of formaldehyde content in the resin was made possible using a six-factor calibration with an R 2 (cal) value of 0.973, and R 2 (CV) value of 0.929 and a root-mean-square error of cross-validation of 0.01. This calibration was then used to generate control charts of formaldehyde content at regular four-hourly periods during MDF panel manufacture in a commercial MDF manufacturing plant.

Adhesive bonding and performance testing of bonded wood products

Treesearch

Charles R. Frihart

2005-01-01

Despite the importance of durable wood bonds, the factors that lead to durability are not well understood, and the internal forces exerted upon the bondline are often overlooked. Durability requires that the bonded assembly resist dimensional changes of wood with fluctuation of wood moisture levels. Both bonding and bond breaking steps need to be understood at cellular...

Fabrication of titanium multi-wall Thermal Protection System (TPS) test panel arrays

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E.; Rosenthal, H. A.

1980-01-01

Several arrays were designed and tested. Tests included vibrational and acoustical tests, radiant heating tests, and thermal conductivity tests. A feasible manufacturing technique was established for producing the protection system panels.

Pallets: A Growing Source of Recycled Wood

Treesearch

Robert J. Bush; Vijay S. Reddy; Philip A. Araman

1997-01-01

Considerable volumes of solid hardwoods, solid softwoods, and wood panels are used to manufacture pallets and containers in the United States. Increasing quantities of these materials are recovered from the waste stream for reuse and recycling. Two important groups involved in this recovery and recycling are firms in the pallet industry (SIC 2448) and landfill...

Carbon Mitigation Impacts of Increased Softwood Lumber and Structural Panel Use for Nonresidential Construction in the United States

Treesearch

Prakash Nepal; Kenneth E. Skog; David B. McKeever; Richard D. Bergman; Karen L. Abt; Robert C. Abt

2016-01-01

More wood use in the United States to construct low-rise nonresidential (NR) buildings would increase consumption and production of softwood (SW) lumber, engineered wood products, and structural and nonstructural wood panels. Using a consequential life-cycle analysis, we estimated the change in net CO2 emissions thatwould be caused by increased...

Nondestructive testing for assessing wood members in structures : a review

Treesearch

R. J. Ross; R. F. Pellerin

1994-01-01

Numerous organizations have conducted research to develop nondestructive testing (NDT) techniques for assessing the condition of wood members in structures. A review of this research was published in 1991. This is an update of the 1991 report. It presents a comprehensive review of published research on the development and use of NDT tools for in-place assessment of...

Machine Vision System for Color Sorting Wood Edge-Glued Panel Parts

Treesearch

Qiang Lu; S. Srikanteswara; W. King; T. Drayer; Richard Conners; D. Earl Kline; Philip A. Araman

1997-01-01

This paper describes an automatic color sorting system for hardwood edge-glued panel parts. The color sorting system simultaneously examines both faces of a panel part and then determines which face has the "better" color given specified color uniformity and priority defined by management. The real-time color sorting system software and hardware are briefly...

Consumer and manufacturer perceptions of hardwood panels made from character-marked lumber

Treesearch

D. Nicholls; M. Bumgardner; V. Barber

2010-01-01

Hardwood panels made from edge-glued material are a versatile product that could be within the reach of many smaller wood products firms. However, products would need to be accepted throughout the supply chain for this opportunity to be achieved. This study evaluated preferences of consumers and manufacturers towards edge-glued panels from Alaskan red alder and paper...

Simple go/no-go test for subcritical damage in body armor panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisher, Jason; Chimenti, D. E.

2011-06-23

The development of a simple test for subcritical damage in body armor panels using pressure-sensitive dye-indicator film has been performed and demonstrated effective. Measurements have shown that static indicator levels are accurately reproduced in dynamic loading events. Impacts from hard blunt impactors instrumented with an accelerometer and embedded force transducer were studied. Reliable correlations between the indicator film and instrumented impact force are shown for a range of impact energies. Force and acceleration waveforms with corresponding indicator film results are presented for impact events onto damaged and undamaged panels. We find that panel damage can occur at impact levels farmore » below the National Institute of Justice acceptance test standard.« less

Buckling analysis and test correlation of hat stiffened panels for hypersonic vehicles

NASA Technical Reports Server (NTRS)

Percy, Wendy C.; Fields, Roger A.

1990-01-01

The paper discusses the design, analysis, and test of hat stiffened panels subjected to a variety of thermal and mechanical load conditions. The panels were designed using data from structural optimization computer codes and finite element analysis. Test methods included the grid shadow moire method and a single gage force stiffness method. The agreement between the test data and analysis provides confidence in the methods that are currently being used to design structures for hypersonic vehicles. The agreement also indicates that post buckled strength may potentially be used to reduce the vehicle weight.

EFFECTS OF BURN RATE, WOOD SPECIES, MOISTURE CONTENT AND WEIGHT OF WOOD LOADED ON WOODSTOVE EMISSIONS

EPA Science Inventory

The report gives results of tests of four woodstove operating parameters (burn rate, wood moisture, wood load, and wood species) at two levels each using a half factorial experimental test design to determine statistically significant effects on the emission components CO, CO2, p...

Use of wood in buildings and bridges

Treesearch

James P. Wacker

2010-01-01

In this chapter, the features of various types of building systems are described. Emphasis is placed on how these systems have adapted to the use of modern materials and techniques. For example, where floor, wall, and roof sheathing for light-frame construction were once commonly made from wood boards, sheathing is now commonly made from structural panel products, such...

Experimental and Theoretical Analysis of Sound Absorption Properties of Finely Perforated Wooden Panels

PubMed Central

Song, Boqi; Peng, Limin; Fu, Feng; Liu, Meihong; Zhang, Houjiang

2016-01-01

Perforated wooden panels are typically utilized as a resonant sound absorbing material in indoor noise control. In this paper, the absorption properties of wooden panels perforated with tiny holes of 1–3 mm diameter were studied both experimentally and theoretically. The Maa-MPP (micro perforated panels) model and the Maa-Flex model were applied to predict the absorption regularities of finely perforated wooden panels. A relative impedance comparison and full-factorial experiments were carried out to verify the feasibility of the theoretical models. The results showed that the Maa-Flex model obtained good agreement with measured results. Control experiments and measurements of dynamic mechanical properties were carried out to investigate the influence of the wood characteristics. In this study, absorption properties were enhanced by sound-induced vibration. The relationship between the dynamic mechanical properties and the panel mass-spring vibration absorption was revealed. While the absorption effects of wood porous structure were not found, they were demonstrated theoretically by using acoustic wave propagation in a simplified circular pipe with a suddenly changed cross-section model. This work provides experimental and theoretical guidance for perforation parameter design. PMID:28774063

Experimental and Theoretical Analysis of Sound Absorption Properties of Finely Perforated Wooden Panels.

PubMed

Song, Boqi; Peng, Limin; Fu, Feng; Liu, Meihong; Zhang, Houjiang

2016-11-22

Perforated wooden panels are typically utilized as a resonant sound absorbing material in indoor noise control. In this paper, the absorption properties of wooden panels perforated with tiny holes of 1-3 mm diameter were studied both experimentally and theoretically. The Maa-MPP (micro perforated panels) model and the Maa-Flex model were applied to predict the absorption regularities of finely perforated wooden panels. A relative impedance comparison and full-factorial experiments were carried out to verify the feasibility of the theoretical models. The results showed that the Maa-Flex model obtained good agreement with measured results. Control experiments and measurements of dynamic mechanical properties were carried out to investigate the influence of the wood characteristics. In this study, absorption properties were enhanced by sound-induced vibration. The relationship between the dynamic mechanical properties and the panel mass-spring vibration absorption was revealed. While the absorption effects of wood porous structure were not found, they were demonstrated theoretically by using acoustic wave propagation in a simplified circular pipe with a suddenly changed cross-section model. This work provides experimental and theoretical guidance for perforation parameter design.

Housing and Wood Products Assessment.

DTIC Science & Technology

1982-12-10

1981 to a peak of of floor area, the North Central almost 3 million in 1972 when region 1,670 square feet, the government subsidy programs were South...other masonry alterations. lumber by plywood. Lumber has Interior decorative panel already been effectively elimina- products are also used widely in...possible savings in walls . already been effectively elimi- is 25 percent and 40 percent on nated in these markets and future roofs. Wood joist floor

Test and Analyses of a Composite Multi-Bay Fuselage Panel Under Uni-Axial Compression

NASA Technical Reports Server (NTRS)

Li, Jian; Baker, Donald J.

2004-01-01

A composite panel containing three stringers and two frames cut from a vacuum-assisted resin transfer molded (VaRTM) stitched fuselage article was tested under uni-axial compression loading. The stringers and frames divided the panel into six bays with two columns of three bays each along the compressive loading direction. The two frames were supported at the ends with pins to restrict the out-of-plane translation. The free edges of the panel were constrained by knife-edges. The panel was modeled with shell finite elements and analyzed with ABAQUS nonlinear solver. The nonlinear predictions were compared with the test results in out-of-plane displacements, back-to-back surface strains on stringer flanges and back-to-back surface strains at the centers of the skin-bays. The analysis predictions were in good agreement with the test data up to post-buckling.

Re-design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E., Jr.; Rosenthal, H. A.

1984-01-01

The Titanium Multi-wall Thermal Protection System (TIPS) panel was re-designed to incorporate Ti-6-2-4-2 outer sheets for the hot surface, ninety degree side closures for ease of construction and through panel fastness for ease of panel removal. Thermal and structural tests were performed to verify the design. Twenty-five panels were fabricated and delivered to NASA for evaluation at Langley Research Center and Johnson Space Center.

Craftsmen in the Wood Model Shop at the Lewis Flight Propulsion Laboratory

NASA Image and Video Library

1953-01-21

Craftsmen work in the wood model shop at the National Advisory Committee for Aeronautics (NACA) Lewis Flight Propulsion Laboratory. The Fabrication Division created almost all of the equipment and models used at the laboratory. The Fabrication Shop building contained a number of specialized shops in the 1940s and 1950s. These included a Machine Shop, Sheet Metal Shop, Wood Model and Pattern Shop, Instrument Shop, Thermocouple Shop, Heat Treating Shop, Metallurgical Laboratory, and Fabrication Office. The Wood Model and Pattern Shop created everything from control panels and cabinets to aircraft models molds for sheet metal work.

Is Follow-Up Testing with the FilmArray Gastrointestinal Multiplex PCR Panel Necessary?

PubMed Central

Park, Sholhui; Hitchcock, Matthew M.; Gomez, Carlos A.

2017-01-01

ABSTRACT The FilmArray gastrointestinal (GI) panel (BioFire Diagnostics, Salt Lake City, UT) is a simple, sample-to-answer, on-demand, multiplex, nucleic acid amplification test for syndromic diagnosis of infectious gastroenteritis. The aim of this study was to measure the yield of follow-up testing with FilmArray GI panel within 4 weeks of an initial test. Consecutive adult and pediatric patients tested at an academic institution between August 2015 and June 2016 were included in this study. Of 145 follow-up tests in 106 unique patients with an initial negative result, 134 (92.4%) tests and 98 (92.5%) patients remained negative upon follow-up testing. Excluding targets that are not reported at this institution (Clostridium difficile, enteroaggregative Escherichia coli, enteropathogenic E. coli, and enterotoxigenic E. coli), 137 (94.5%) follow-up tests and 101 (95.3%) patients remained negative. Weekly conversion rates were not significantly different across the 4-week follow-up interval. No epidemiological or clinical factors were significantly associated with a negative to positive conversion. Of 80 follow-up tests in patients with an initial positive result, 43 (53.8%) remained positive for the same target, 34 (42.5%) were negative, and 3 were positive for a different target (3.8%). Follow-up testing with FilmArray GI panel within 4 weeks of a negative result rarely changed the initial result, and the follow-up test reverted to negative less than half the time after an initial positive result. In the absence of clinical or epidemiological evidence for a new infection, follow-up testing should be limited and FilmArray GI panel should not be used as a test of cure. PMID:28122874

Solar energy panel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hyman, M.

1980-03-04

A light-weight, low-cost and high efficiency solar panel includes a light-weight rectangular wood frame which surrounds and houses a copper absorber plate. A pair of spaced glazings, formed from plastic film materials, are disposed above the absorber to define a pair of enclosed air spaces. The lower glazing is capable of withstanding high temperatures and the upper glazing material is capable of providing good weather resistance. The material of the upper glazing extends fully about the frame to protect the entire frame from weathering. Insulation is provided beneath the absorber plate. The frame rests on top of a bottom sheetmore » of insulative foam plastic which is wrapped in a plastic envelope. The surrounding film of the outer glazing is bonded securely to the envelope to encase the entire panel within a protective sealed envelope of weather-resistant plastic film.« less

Full-Scale Test and Analysis of a PRSEUS Fuselage Panel to Assess Damage-Containment Features

NASA Technical Reports Server (NTRS)

Bergan, Andrew; Bakuckas, John G.; Lovejoy, Andrew E.; Jegley, Dawn C.; Linton, Kim A.; Korkosz, Gregory; Awerbuch, Jonathan; Tan, Tein-Min

2011-01-01

Stitched composite technology has the potential to substantially decrease structural weight through enhanced damage containment capabilities. The most recent generation of stitched composite technology, the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept, has been shown to successfully arrest damage at the sub-component level through tension testing of a three stringer panel with damage in the form of a two-bay notch. In a joint effort undertaken by the National Aeronautics and Space Administration (NASA), the Federal Aviation Administration (FAA), and the Boeing Company, further studies are being conducted to characterize the damage containment features of the PRSEUS concept. A full-scale residual strength test will be performed on a fuselage panel to determine if the load capacity will meet strength, deformation, and damage tolerance requirements. A curved panel was designed, fabricated, and prepared for residual strength testing. A pre-test Finite Element Model (FEM) was developed using design allowables from previous test programs to predict test panel deformation characteristics and margins of safety. Three phases of testing with increasing damage severity include: (1) as manufactured; (2) barely visible impact damage (BVID) and visible impact damage (VID); and (3) discrete source damage (DSD) where the panel will be loaded to catastrophic failure. This paper presents the background information, test plan, and experimental procedure. This paper is the first of several future articles reporting the test preparations, results, and analysis conducted in the test program.

Effect of precipitation pattern on leaching of preservative from treated wood and implications for accelerated testing

Treesearch

Stan Lebow

2014-01-01

There is a need to develop improved accelerated test methods for evaluating the leaching of wood preservatives from treated wood exposed to precipitation. In this study the effects of rate of rainfall and length of intervals between rainfall events on leaching was evaluated by exposing specimens to varying patterns of simulated rainfall under controlled laboratory...

Progress and Strategies for Testing of Materials for Solar Panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurtz, Sarah

Accelerated testing is key to confident launch of a new product. However, for new products like solar panels, the best approach is not always clear. The challenge for materials manufacturers is that test times can be long. Also, small-coupon testing may not predict the behavior in the full-size module, but testing of the full-size module is too expensive. As a result, solar panel test standards like IEC 61215 are useful, but are not sufficient. Material manufacturers have needed to define their own test protocols. This presentation will review some historical data (e.g., data show that manufacturers are making great progressmore » toward reducing encapsulant discoloration) and describe advances in material testing (for example, new techniques are being demonstrated on how to more quantitatively assess adhesion, detect tendency for delamination, and understand how encapsulant properties affect other properties like cracking of cells). The International PV Quality Assurance Task Force has been researching climate-specific weathering tests toward the goal of defining international standards that would simplify qualification and quality assurance testing for materials. The status of these tests and the strategies for how to organize these standards to best meet the needs of the industry will be discussed.« less

Cone calorimeter tests of wood-based decking materials

Treesearch

Robert H. White; Mark A. Dietenberger; Nicole M. Stark

2007-01-01

New technologies in building materials have resulted in the use of a wide variety of materials in decks. As part of our effort to address fire concerns in the wildland-urban interface, the Forest Products Laboratory has been examining the fire performance of decking products. In addition to preservative-treated wood, decking products include wood-plastic composites and...

Determination of native (wood derived) formaldehyde by the desiccator method in particleboards generated during panel production

Treesearch

Michael J. Birkeland; Linda Lorenz; James M. Wescott; Charles R. Frihart

2010-01-01

Hot-pressing wood, particularly in the production of wood composites, generates significant ‘‘native’’ (wood-based) formaldehyde (FA), even in the absence of adhesive. The level of native FA relates directly to the time and temperature of hot-pressing. This native FA dissipates in a relatively short time and is not part of the long-term FA emission issue commonly...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

46 CFR 148.325 - Wood chips; wood pellets; wood pulp pellets.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Wood chips; wood pellets; wood pulp pellets. 148.325... § 148.325 Wood chips; wood pellets; wood pulp pellets. (a) This part applies to wood chips and wood pulp... cargo hold. (b) No person may enter a cargo hold containing wood chips, wood pellets, or wood pulp...

Edge-glued panels from Alaska hardwoods: retail manager perspectives

Treesearch

David Nicholls; Matthew Bumgardner; Valerie Barber

2010-01-01

In Alaska, red alder (Alnus rubra Bong.) and paper birch (Betula papyrifera Marsh.) are both lesser-known hardwoods grown, harvested, and manufactured into appearance products, with potential for increased utilization. The production of edgeglued panels from red alder and paper birch offers one expansion opportunity for wood...

Interaction of ozone with wooden building products, treated wood samples and exotic wood species

NASA Astrophysics Data System (ADS)

Schripp, Tobias; Langer, Sarka; Salthammer, Tunga

2012-07-01

Wooden building products indoors are known to be able to affect the perceived air quality depending on their emission strength. The indoor application of modern ecological lacquer systems (eco-lacquers or 'green' lacquers) may be a much stronger source than the substrates itself. Especially with regard to the formation of ultrafine particles by gas-to-particle conversion in the presence of ozone or other reactive species the impact of the applied building products on the indoor air quality has to be addressed. The present study reports a two concentration step ozonation of OSB panels, painted beech boards, and a number of solid 'exotic' wood types in a 1 m³ emission test chamber. The emission of volatile organic compounds (VOC) was recorded as well as the formation of ultrafine particles in the range 7-300 nm. The products are characterized on the basis of their ozone deposition velocity; the obtained values of 0.008-0.381 cm s-1 are comparable with previously published data. Within the samples of the present study one eco-lacquer was the strongest source of VOC (total VOC ˜ 60 mg m-3) while the wooden building products (OSB) were of intermediate emission strength. The lowest emission was found for the solid (exotic) wood samples. The VOC release of the samples corresponded roughly to the particle formation potential. However, the strongest UFP formation was measured for one solid wood sample ('Garapa') which showed a strong surface reaction in the presence of ozone and formed a large number of particles <40 nm. Overall, the experiments demonstrated the necessity of real-life samples for the estimation of UFP indoor air pollution from the ozone chemistry of terpenes.

Design, testing, and damage tolerance study of bonded stiffened composite wing cover panels

NASA Technical Reports Server (NTRS)

Madan, Ram C.; Sutton, Jason O.

1988-01-01

Results are presented from the application of damage tolerance criteria for composite panels to multistringer composite wing cover panels developed under NASA's Composite Transport Wing Technology Development contract. This conceptual wing design integrated aeroelastic stiffness constraints with an enhanced damage tolerance material system, in order to yield optimized producibility and structural performance. Damage tolerance was demonstrated in a test program using full-sized cover panel subcomponents; panel skins were impacted at midbay between stiffeners, directly over a stiffener, and over the stiffener flange edge. None of the impacts produced visible damage. NASTRAN analyses were performed to simulate NDI-detected invisible damage.

Thermal fatigue tests of a radiative heat shield panel for a hypersonic transport

NASA Technical Reports Server (NTRS)

Webb, Granville L.; Clark, Ronald K.; Sharpe, Ellsworth L.

1985-01-01

A pair of corrugation stiffened, beaded skin Rene 41 heat shield panels were exposed to 20,000 thermal cycles between room temperature and 1450 F to evaluate the thermal fatigue response of Rene 41 metallic heat shields for hypersonic cruise aircraft applications. At the conclusion of the tests, the panels retained substantial structural integrity; however, there were cracks and excessive wear in the vicinity of fastener holes and there was an 80-percent loss in ductility of the skin. Shrinkage of the panel which caused the cracks and wear must be considered in design of panels for Thermal Protection Systems (TPS) applications.

An oxidation and erosion test facility for cooled panels

NASA Technical Reports Server (NTRS)

Swartwout, W. H.; Erdos, J. I.; Engers, R. J.; Prescott, C.

1992-01-01

The Panel Oxidation and Erosion Testbed (POET) facility under construction at GASL to provide the required test environment is described. The POET facility comprises three major element including a vitiated air heater, a supersonic nozzle, and a test section. A hydrogen-fueld vitiated air heater will provide the oxidizing and erosive environment. The flow through the test section characterized by low supersonic speed and Mach number of 1.4 will maximize the local heat transfer rate and the local surface shear stress.

Comparison of performance of wood extractives as preservatives in field tests against termites and decay in the USA and Pakistan

Treesearch

Babar Hassan; Sohail Ahmed; Mark Mankowski; Grant Kirker

2017-01-01

Increasing environmental regulations have limited the use of certain broad spectrum synthetic pesticides as wood preservatives creating a need for more environmentally benign wood preservative systems. Biocidal compounds from natural products have been proposed as alternatives to commercial wood preservatives, but field data from long term performance testing is...

Minimum prick test panel for adult patients with asthma and rhinitis in Ankara, Turkey.

PubMed

Comert, Sule; Demir, A Ugur; Karakaya, Gul; Kalyoncu, A Fuat

2014-05-01

Determination of the number and type of allergens needed to be tested in epidemiological studies is important in order to identify most of the sensitized subjects with a cost-effective approach. This study aimed to investigate the minimum skin prick test panel for the identification of at least 95% of the sensitized subjects with symptoms of asthma and/or allergic rhinitis (AR) in Ankara, Turkey. Skin prick test results of 7492 patients who were referred to our outpatient clinic with clinical symptoms of asthma and/or AR between 1991 and 2005 were evaluated retrospectively. Seven allergens were tested in all and 13 allergens in 4202 patients. The allergen group needed for detection of 95% of the sensitized subjects was determined for both the 7 and 13 allergen panels. The study protocol was approved by the local ethics committee of Hacettepe University. The atopy prevalences in the whole study population and in 4202 patients tested with the 13 allergen panel were calculated as 32.2% and 42.6%, respectively. Three allergens (Phleum pratense, Dermatophagoides pteronyssinus and Artemisia vulgaris) within the 7 allergen panel were adequate for the identification of at least 95% of the sensitized subjects. Olea europae was added to the previous three allergens when the 13 allergen panel was applied. Three to four allergens are sufficient for identification at least 95% of sensitized subjects with asthma and/or AR in Ankara, Turkey.

Alaska birch for edge-glued panel production—considerations for wood products manufacturers

Treesearch

David Nicholls

2010-01-01

Edge-glued panels could become a natural extension for the birch (Betula papyrifera Marsh.) lumber industry in Alaska, resulting in greater utilization of the birch resource while allowing producers to explore a wider variety of products and markets. Key advantages of edge-glued panel production include the relatively low cost of equipment, the...

Design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E., Jr.; Rosenthal, H. A.

1980-01-01

A titanium multiwall thermal protection system panel was designed. The panel is a nine sheet sandwich structure consisting of an upper and lower face sheet; four dimpled sheets, three septum sheets, and clips for attachment to a vehicle structure. An acceptable fabrication process was developed, and the panel design was verified through mechanical and thermal testing of component specimens. A design was completed which takes into consideration fabrication techniques, thermal properties, mechanical properties, and materials availability.

The effect of aspen wood characteristics and properties on utilization

Treesearch

Kurt H. Mackes; Dennis L. Lynch

2001-01-01

This paper reviews characteristics and properties of aspen wood, including anatomical structure and characteristics, moisture and shrinkage properties, weight and specific gravity, mechanical properties, and processing characteristics. Uses of aspen are evaluated: sawn and veneer products, composite panels, pulp, excelsior, post and poles, animal bedding, animal food...

An Investigation on Computer-Adaptive Multistage Testing Panels for Multidimensional Assessment

ERIC Educational Resources Information Center

Wang, Xinrui

2013-01-01

The computer-adaptive multistage testing (ca-MST) has been developed as an alternative to computerized adaptive testing (CAT), and been increasingly adopted in large-scale assessments. Current research and practice only focus on ca-MST panels for credentialing purposes. The ca-MST test mode, therefore, is designed to gauge a single scale. The…

Steel test panel helps control additives in pyrophosphate copper plating

NASA Technical Reports Server (NTRS)

Hollar, W. T.

1967-01-01

Test panel helps control maximum tolerance level for plating solution contaminants. It provides low, medium, and high-current density areas such as exist in production plating, and plating is examined for uniformity of texture and ductility.

Why do some wood-adhesive bonds respond poorly to accelerated moisture-resistant tests?

Treesearch

Charles R. Frihart; James M. Wescott

2008-01-01

The most challenging part of developing acceptable adhesives for wood bonding often is to create a bond that will withstand exposure to wet conditions or wet/dry cycles. Products that pass these tests have been developed empirically, but the aspects that make it difficult for adhesives to pass these tests and systematically ways to develop more durable adhesive bonds...

Test/semi-empirical analysis of a carbon/epoxy fabric stiffened panel

NASA Technical Reports Server (NTRS)

Spier, E. E.; Anderson, J. A.

1990-01-01

The purpose of this work-in-progress is to present a semi-empirical analysis method developed to predict the buckling and crippling loads of carbon/epoxy fabric blade stiffened panels in compression. This is a hand analysis method comprised of well known, accepted techniques, logical engineering judgements, and experimental data that results in conservative solutions. In order to verify this method, a stiffened panel was fabricated and tested. Both the best and analysis results are presented.

Carbon Balance and Contribution of Harvested Wood Products in China Based on the Production Approach of the Intergovernmental Panel on Climate Change.

PubMed

Ji, Chunyi; Cao, Wenbin; Chen, Yong; Yang, Hongqiang

2016-11-12

The carbon sequestration of harvested wood products (HWP) plays an important role in climate mitigation. Accounting the carbon contribution of national HWP carbon pools has been listed as one of the key topics for negotiation in the United Nations Framework Convention on Climate Change. On the basis of the revised Production Approach of the Intergovernmental Panel on Climate Change (2013) (IPCC), this study assessed the accounting of carbon stock and emissions from the HWP pool in China and then analyzed its balance and contribution to carbon mitigation from 1960 to 2014. Research results showed that the accumulated carbon stock in China's HWP carbon pool increased from 130 Teragrams Carbon (TgC) in 1960 to 705.6 TgC in 2014. The annual increment in the carbon stock rose from 3.2 TgC in 1960 to 45.2 TgC in 2014. The category of solid wood products accounted for approximately 95% of the annual amount. The reduction in carbon emissions was approximately twelve times that of the emissions from the HWP producing and processing stage during the last decade. Furthermore, the amount of carbon stock and emission reduction increased from 23 TgC in 1960 to 76.1 TgC in 2014. The annual contribution of HWP could compensate for approximately 2.9% of the national carbon dioxide emissions in China.

Carbon Balance and Contribution of Harvested Wood Products in China Based on the Production Approach of the Intergovernmental Panel on Climate Change

PubMed Central

Ji, Chunyi; Cao, Wenbin; Chen, Yong; Yang, Hongqiang

2016-01-01

The carbon sequestration of harvested wood products (HWP) plays an important role in climate mitigation. Accounting the carbon contribution of national HWP carbon pools has been listed as one of the key topics for negotiation in the United Nations Framework Convention on Climate Change. On the basis of the revised Production Approach of the Intergovernmental Panel on Climate Change (2013) (IPCC), this study assessed the accounting of carbon stock and emissions from the HWP pool in China and then analyzed its balance and contribution to carbon mitigation from 1960 to 2014. Research results showed that the accumulated carbon stock in China’s HWP carbon pool increased from 130 Teragrams Carbon (TgC) in 1960 to 705.6 TgC in 2014. The annual increment in the carbon stock rose from 3.2 TgC in 1960 to 45.2 TgC in 2014. The category of solid wood products accounted for approximately 95% of the annual amount. The reduction in carbon emissions was approximately twelve times that of the emissions from the HWP producing and processing stage during the last decade. Furthermore, the amount of carbon stock and emission reduction increased from 23 TgC in 1960 to 76.1 TgC in 2014. The annual contribution of HWP could compensate for approximately 2.9% of the national carbon dioxide emissions in China. PMID:27845760

141. NITROGEN TEST PANEL ON EAST WALL OF AGENA TRANSFER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

141. NITROGEN TEST PANEL ON EAST WALL OF AGENA TRANSFER AREA SHELTER (117A), LSB (BLDG. 770) - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 West, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

Thermal stability tests of CFRP sandwich panels for far infrared astronomy

NASA Technical Reports Server (NTRS)

Hoffmann, W. F.; Helwig, G.; Scheulen, D.

1986-01-01

An account is given of fabrication methods and low temperature figure tests for CFRP sandwich panels, in order to ascertain their applicability to ultralightweight 3-m aperture primary mirrors for balloon-borne sub-mm and far-IF telescopes that must maintain a 1-2 micron rms surface figure accuracy at -40 to -50 C. Optical figure measurements on the first two of a series of four 0.5-m test panels, replicated to a spherical surface, show a radius-of-curvature change and astigmatism down to -60 C; this approximately follows the composite's theoretical predictions and implies that material and process control is excellent, so that the large scale changes observed can be compensated for.

Characterization of wood mulch and leachate/runoff from three wood recycling facilities.

PubMed

Kannepalli, Sarat; Strom, Peter F; Krogmann, Uta; Subroy, Vandana; Giménez, Daniel; Miskewitz, Robert

2016-11-01

Large-scale open storage of wood mulch is common practice at wood recycling facilities. During rain and snow melt, leachate with soluble compounds and suspended particles is released from mulch stockpiles. The objective of this study was to determine the quality of leachate/runoff from wood recycling facilities to evaluate its potential to contaminate receiving waterbodies. Wood mulch (n = 30) and leachate/runoff (n = 26) samples were collected over 1.5 years from three wood recycling facilities in New Jersey, USA. Differences by site were found (p < 0.05) for most of the 21 constituents tested in the solid wood mulch samples. Biochemical oxygen demand (range <20-3000 mg/L), chemical oxygen demand (134-6000 mg/L) and total suspended solids (69-401 mg/L) median concentrations of the leachate/runoff samples were comparable to those of untreated domestic wastewater. Total Kjeldahl N, total P and fecal coliform median values were slightly lower than typical wastewater values. Dose-response studies with leachate/runoff samples using zebrafish (Danio rerio) embryos showed that mortality and developmental defects typically did not occur even at the highest concentration tested, indicating low toxicity, although delayed development did occur. Based on this study, leachate/runoff from wood recycling facilities should not be released to surface waters as it is a potential source of organic contamination and low levels of nutrients. A study in which runoff from a controlled drainage area containing wood mulch of known properties is monitored would allow for better assessment of the potential impact of stormwater runoff from wood recycling facilities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Experimental vibroacoustic testing of plane panels using synthesized random pressure fields.

PubMed

Robin, Olivier; Berry, Alain; Moreau, Stéphane

2014-06-01

The experimental reproduction of random pressure fields on a plane panel and corresponding induced vibrations is studied. An open-loop reproduction strategy is proposed that uses the synthetic array concept, for which a small array element is moved to create a large array by post-processing. Three possible approaches are suggested to define the complex amplitudes to be imposed to the reproduction sources distributed on a virtual plane facing the panel to be tested. Using a single acoustic monopole, a scanning laser vibrometer and a baffled simply supported aluminum panel, experimental vibroacoustic indicators such as the Transmission Loss for Diffuse Acoustic Field, high-speed subsonic and supersonic Turbulent Boundary Layer excitations are obtained. Comparisons with simulation results obtained using a commercial software show that the Transmission Loss estimation is possible under both excitations. Moreover and as a complement to frequency domain indicators, the vibroacoustic behavior of the panel can be studied in the wave number domain.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives

PubMed Central

Shao, Dongwei; Xu, Min; Cai, Liping; Shi, Sheldon Q.

2016-01-01

Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs), this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%–50% at rotor rotational speeds of 15–45 rpm and filled coefficients of 0.55–0.75. Four regression equations, i.e., the tensile strength (Ts), elongation at break (Eb), hardness (Ha) and rebound resilience (Rr) as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the Ts, Eb and Rr of the panels were reduced, Ha was considerably increased by 17%–58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%–3%, which was much lower than commercial wood-based composites. PMID:28773591

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives.

PubMed

Shao, Dongwei; Xu, Min; Cai, Liping; Shi, Sheldon Q

2016-06-14

Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs), this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%-50% at rotor rotational speeds of 15-45 rpm and filled coefficients of 0.55-0.75. Four regression equations, i.e. , the tensile strength ( T s), elongation at break ( E b), hardness ( H a) and rebound resilience ( R r) as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the T s, E b and R r of the panels were reduced, H a was considerably increased by 17%-58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%-3%, which was much lower than commercial wood-based composites.

A research program to reduce interior noise in general aviation airplanes. Design of an acoustic panel test facility

NASA Technical Reports Server (NTRS)

Roskam, J.; Muirhead, V. U.; Smith, H. W.; Henderson, T. D.

1977-01-01

The design, construction, and costs of a test facility for determining the sound transmission loss characteristics of various panels and panel treatments are described. The pressurization system and electronic equipment used in experimental testing are discussed as well as the reliability of the facility and the data gathered. Tests results are compared to pertinent acoustical theories for panel behavior and minor anomalies in the data are examined. A method for predicting panel behavior in the stiffness region is also presented.

Performance of fasteners in wood flour-thermoplastic composite panels

Treesearch

Robert H. Falk; Daniel J. Vos; Steven M. Cramer; Brent W. English

2001-01-01

In the building community, there is a growing demand for high-performance, low-maintenance, and low-cost building products. To meet this demand, natural fiberthermoplastic composites are being used to produce such products as decking, window and door elements, panels, roofing, and siding. In spite of the rapid growth in the use of these composites, little is known...

Acoustic testing to enhance western forest values and meet customer wood quality needs

Treesearch

Peter Carter; David Briggs; Robert J. Ross; Xiping Wang

2005-01-01

Nondestructive testing (NDT) of wood products, such as lumber and veneer, for stiffness and strength evaluation has been proven and commercialized for many years. The NDT concept has been extended and commercialized in the Director HM-200™ tool for testing logs in advance of processing so manufacturers can make more informed log purchases and better match logs to...

Hygrothermal Properties of Cross Laminated Timber and Moisture Response of Wood at High Relative Humidity

NASA Astrophysics Data System (ADS)

AlSayegh, George

Cross Laminated Timber (CLT) is a new wood-based material composed of cross laminated wood boards that form a structural panel. This study focuses on identifying the appropriate methods to determine the hygrothermal properties of CLTs fabricated with Canadian and European Lumber. The laboratory tests carried out in this study will help establish heat, air and moisture response properties to be used for hygrothermal simulation to assess the durability of CLTs in building envelope construction. Measurement of water vapour permeability, liquid water absorption, sorption isotherms, thermal conductivity, and air permeability were performed on three Canadian CLT specimens composed of Hem-Fir, Eastern Spruce-Pine-Fir, and Western Spruce-Pine-Fir and one European specimen composed of Spruce. The hygrothermal properties of CLT, considered in this study, appear to be similar to commonly used wood specimens reported in the literature. However, liquid water absorption coefficients of CLT were found to be generally lower than common wood species, possibly due to the presence of glue between the wood layers which limits the moisture movement across the specimen. On the other hand, the air permeability across the CLT specimens varied due to the glue discontinuity within the specimen which led some CLTs to be permeable, however all the European specimens were found to be impermeable. This study also critically analyzed the significance of equilibrium moisture content (EMC) of wood at high relative humidity, measured by means of a pressure plate apparatus and humidity chambers, on the moisture management performance of a wood-frame stucco wall, using the hygrothermal simulation tool hygIRC-2D. The simulation results indicate that the prediction of the moisture response of a wood-frame stucco wall assembly depends significantly on the method adopted to derive the EMC of wood at high RH.

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED REAR DOOR, AND ROW OF 6-LIGHT OVER 1-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS AROUND EAST CORNER OF HOUSE. VIEW TO EAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Solar concentrator panel and gore testing in the JPL 25-foot space simulator

NASA Technical Reports Server (NTRS)

Dennison, E. W.; Argoud, M. J.

1981-01-01

The optical imaging characteristics of parabolic solar concentrator panels (or gores) have been measured using the optical beam of the JPL 25-foot space simulator. The simulator optical beam has been characterized, and the virtual source position and size have been determined. These data were used to define the optical test geometry. The point source image size and focal length have been determined for several panels. A flux distribution of a typical solar concentrator has been estimated from these data. Aperture photographs of the panels were used to determine the magnitude and characteristics of the reflecting surface errors. This measurement technique has proven to be highly successful at determining the optical characteristics of solar concentrator panels.

Fire resistance of exposed wood members

Treesearch

Robert H. White

2004-01-01

Fire resistance data on exposed wood beams and columns are plentiful, but few studies have been done on exposed wood members in tension and in decks. To provide data to verify the application of a new calculation procedure, a limited series of fire resistance tests were conducted on wood members loaded in tension and on exposed wood decks.

Life cycle assessment of wood wastes: A case study of ephemeral architecture.

PubMed

Rivela, Beatriz; Moreira, María Teresa; Muñoz, Iván; Rieradevall, Joan; Feijoo, Gumersindo

2006-03-15

One of the most commonly used elements in ephemeral architecture is a particleboard panel. These types of wood products are produced from wood wastes and they are used in temporary constructions such as trade fairs. Once the event is over, they are usually disposed into landfills. This paper intends to assess the environmental effects related to the use of these wood wastes in the end-of-life stage. The Life Cycle Assessment (LCA) of two scenarios was performed, considering the recycling of wood waste for particleboard manufacture and energy generation from non-renewable resources (Scenario 1) versus the production of energy from the combustion of wood waste and particleboard manufacture with conventional wooden resources (Scenario 2). A sensitive analysis was carried out taking into account the influence of the percentage of recycled material and the emissions data from wood combustion. According to Ecoindicator 99 methodology, Damage to Human Health and Ecosystem Quality are more significant in Scenario 2 whereas Scenario 1 presents the largest contribution to Damage to Resources. Between the two proposed alternatives, the recycling of wood waste for particleboard manufacture seems to be more favorable under an environmental perspective.

Mechanical properties of wood

Treesearch

David Kretschmann

2010-01-01

The mechanical properties presented in this chapter were obtained from tests of pieces of wood termed “clear” and “straight grained” because they did not contain characteristics such as knots, cross grain, checks, and splits. These test pieces did have anatomical characteristics such as growth rings that occurred in consistent patterns within each piece. Clear wood...

TRMM Solar Array Panels

NASA Technical Reports Server (NTRS)

1998-01-01

This final report presents conclusions/recommendations concerning the TRMM Solar Array; deliverable list and schedule summary; waivers and deviations; as-shipped performance data, including flight panel verification matrix, panel output detail, shadow test summary, humidity test summary, reverse bias test panel; and finally, quality assurance summary.

Resonance Tests on Glass Reinforced Plastic Composite Panels.

DTIC Science & Technology

1981-04-01

glass -- fibre woven roving and glass - fibre chopped strand mat. BP Cellobond A2785-CV resin was used to bond the glass fibre layers to the foam. A rib was...foam slabs were filled with putty. The differences between the panels were the number of layers of glass fibre used on each side, the density of the...ORGANISATION AERONAUTICAL RESEARCH LABORATORIES MELBOURNE, VICTORIA Structures Technical Memorandum 329 RESONANCE TESTS O GLASS REINFORCED PLASTIC

First insights into macro- and meiofaunal colonisation patterns on paired wood/slate substrata at Atlantic deep-sea hydrothermal vents

NASA Astrophysics Data System (ADS)

Cuvelier, Daphne; Beesau, Julie; Ivanenko, Viatcheslav N.; Zeppilli, Daniela; Sarradin, Pierre-Marie; Sarrazin, Jozée

2014-05-01

In 2006, paired wood and slate panels, each equipped with a temperature probe, were deployed on three different localities on and around the Eiffel Tower edifice (Lucky Strike vent field, Mid-Atlantic Ridge) within close proximity of visible hydrothermal activity. Recovery of these panels took place in 2008. For this two-year deployment period, the composition of colonising organisms (both macro-and meiofauna) was assessed, along with image analyses of the deployment sites in 2006 and 2008. Very few significant differences in colonisation between organic (wood) and inorganic (slate) panels were revealed. Rather, the locality of deployment and the local environmental conditions and hydrothermal activity were found to influence taxonomic composition. Variability in microhabitat conditions and biological interactions were hypothesised to interact jointly in shaping new faunal communities on the colonisation substrata.

5-inch-size liquid crystal flat panel display evaluation test by flight simulator

NASA Astrophysics Data System (ADS)

Kawahara, Hiroyasu; Watanabe, Akira; Wakairo, Kaoru; Udagawa, Tomoyuki; Kurihara, Yoichiro

An evaluation test is conducted on the function, performance, and display format of a 5x5 inch flat panel display (FPD) in a flight simulator. The FPD utilizes a color liquid crystal panel that is compact and lightweight and has excellent visibility. The simulator evaluation test is carried out in sequence with the conventional takeoff and landing to altitude, and then conversion to STOL procedures for flight path and subsequent approach and landing. It is shown that the liquid crystal display could be employed as a satisfactory indicator for aircraft instrumentation.

Compression debarking of wood chips.

Treesearch

Rodger A. Arola; John R. Erickson

1973-01-01

Presents results from 2 years testing of a single-pass compression process for debarking wood chips of several species. The most significant variable was season of cut. Depending on species, approximately 70% of the bark was removed from wood cut in the growing season while approximately 45% was removed from wood cut in the dormant season.

Weathering Characteristics of Wood Plastic Composites Reinforced with Extracted or Delignified Wood Flour

PubMed Central

Chen, Yao; Stark, Nicole M.; Tshabalala, Mandla A.; Gao, Jianmin; Fan, Yongming

2016-01-01

This study investigated weathering performance of an HDPE wood plastic composite reinforced with extracted or delignified wood flour (WF). The wood flour was pre-extracted with three different solvents, toluene/ethanol (TE), acetone/water (AW), and hot water (HW), or sodium chlorite/acetic acid. The spectral properties of the composites before and after artificial weathering under accelerated conditions were characterized by Fourier transform infrared (FTIR) spectroscopy, the surface color parameters were analyzed using colorimetry, and the mechanical properties were determined by a flexural test. Weathering of WPC resulted in a surface lightening and a decrease in wood index (wood/HDPE) and flexural strength. WPCs that were reinforced with delignified wood flour showed higher ΔL* and ΔE* values, together with lower MOE and MOR retention ratios upon weathering when compared to those with non-extracted control and extracted WF. PMID:28773732

Hepatitis Panel: MedlinePlus Lab Test Information

MedlinePlus

... this page: https://medlineplus.gov/labtests/hepatitispanel.html Hepatitis Panel To use the sharing features on this page, please enable JavaScript. What is a Hepatitis Panel? Hepatitis is a type of liver disease. ...

Amplicon-Based Sequencing of Soil Fungi from Wood Preservative Test Sites

Treesearch

Grant T. Kirker; Amy B. Bishell; Michelle A. Jusino; Jonathan M. Palmer; William J. Hickey; Daniel L. Lindner

2017-01-01

Soil samples were collected from field sites in two AWPA (American Wood Protection Association) wood decay hazard zones in North America. Two field plots at each site were exposed to differing preservative chemistries via in-ground installations of treated wood stakes for approximately 50 years. The purpose of this study is to characterize soil fungal species and to...

Strength of anisotropic wood and synthetic materials. [plywood, laminated wood plastics, glass fiber reinforced plastics, polymeric film, and natural wood

NASA Technical Reports Server (NTRS)

Ashkenazi, Y. K.

1981-01-01

The possibility of using general formulas for determining the strength of different anisotropic materials is considered, and theoretical formulas are applied and confirmed by results of tests on various nonmetallic materials. Data are cited on the strength of wood, plywood, laminated wood plastics, fiber glass-reinforced plastics and directed polymer films.

Optimization of wood plastic composite decks

NASA Astrophysics Data System (ADS)

Ravivarman, S.; Venkatesh, G. S.; Karmarkar, A.; Shivkumar N., D.; Abhilash R., M.

2018-04-01

Wood Plastic Composite (WPC) is a new class of natural fibre based composite material that contains plastic matrix reinforced with wood fibres or wood flour. In the present work, Wood Plastic Composite was prepared with 70-wt% of wood flour reinforced in polypropylene matrix. Mechanical characterization of the composite was done by carrying out laboratory tests such as tensile test and flexural test as per the American Society for Testing and Materials (ASTM) standards. Computer Aided Design (CAD) model of the laboratory test specimen (tensile test) was created and explicit finite element analysis was carried out on the finite element model in non-linear Explicit FE code LS - DYNA. The piecewise linear plasticity (MAT 24) material model was identified as a suitable model in LS-DYNA material library, describing the material behavior of the developed composite. The composite structures for decking application in construction industry were then optimized for cross sectional area and distance between two successive supports (span length) by carrying out various numerical experiments in LS-DYNA. The optimized WPC deck (Elliptical channel-2 E10) has 45% reduced weight than the baseline model (solid cross-section) considered in this study with the load carrying capacity meeting acceptance criterion (allowable deflection & stress) for outdoor decking application.

Capacity, production, and manufacturing of woodbased panels in North America

Treesearch

Henry Spelter

1994-01-01

This report is an informational report about four wood-based panel industries: particleboard, oriented strandboard, medium density fiberboard, and Southern Pine plywood. Items highlighted are trends in manufacturing and new plant costs, industry manufacturing capacity, and location. Recent data show the greatest amount of growth taking place in the oriented strandboard...

RELATIVE LEACHING AND AQUATIC TOXICITY OF PRESSURE-TREATED WOOD PRODUCTS USING BATCH LEACHING TESTS

EPA Science Inventory

Samples of southern yellow pine dimensional lumber, each treated with one of five different waterborne chemical preservatives, were leached using 18-hour batch leaching tests. The wood preservatives included chromated copper arsenate (CCA), alkaline copper quaternary (ACQ), coppe...

Hepatic (Liver) Function Panel

MedlinePlus

... Educators Search English Español Blood Test: Hepatic (Liver) Function Panel KidsHealth / For Parents / Blood Test: Hepatic (Liver) ... kidneys ) is working. What Is a Hepatic (Liver) Function Panel? A liver function panel is a blood ...

Craftsmen say "we want edge-glued, standard-size panels"

Treesearch

Philip A. Araman; Hugh W. Reynolds

1983-01-01

Wood craftsmen would like an alternative to hardwood lumber and plywood and softwood products. They are very interested in edge-glued, standard-size panels. These conclusions are based on interviews with craftsmen at two trade shows, and the results are included in this report along with our recommendations for optimum acceptance by craftsmen of this new product.

Advances in corrosion testing of metals in contact with treated wood

Treesearch

Samuel Zelinka; D.S. Stone

2010-01-01

A January 2004 change in the regulation of wood preservatives used in the U.S.has increased the use of newer wood preservatives, such as alkaline copper quaternary (ACQ) and copper azole (CuAz). These preservatives contain high amounts of cupric ions, which may be reduced to copper metal at the expense of less noble steel and galvanized fasteners in the wood....

Mean reversion in the current account of forty-eight african countries: Evidence from the Panel SURADF test

NASA Astrophysics Data System (ADS)

Chu, Hsiao-Ping; Chang, Tsangyao; Chang, Hsu-Ling; Su, Chi-Wei; Yuan, Young

2007-10-01

Here, the Panel seemingly unrelated regressions augmented Dickey-Fuller test (SURADF) test, first introduced and advanced by Breuer et al. [Misleading inferences from panel unit-root tests with an illustration from purchasing power parity, Rev. Int. Econ. 9(3) (2001) 482-493], is used to investigate the mean-reverting behavior of the current account of 48 African countries during the 1980-2004 periods. The empirical results from numerous panel-based unit root tests, conducted earlier, indicated that the current account of each of these countries is stationary; however, when Breuer et al.'s (2001) Panel SURADF test is conducted, it is found that a unit root exists in the current account of 11 of the countries studied. These results have one extremely important policy implication for the 48 African countries studied: the current account deficit of most is sustainable, and thus signifying that those nations should have no incentive to default on their international debt.

Sequestration of carbon in harvested wood products for the United States

Treesearch

Kenneth E. Skog

2008-01-01

The Intergovernmental Panel on Climate Change (IPCC) provides guidelines for countries to report greenhouse gas removals by sinks and emissions from sources. These guidelines allow use of several accounting approaches when reporting the contribution of harvested wood products (HWP) under the United Nations Framework Convention on Climate Change. Using extensions of...

Effects of recycled fiber on the properties of fiberboard panels

Treesearch

Chin-yin Hwang; Chung-yun Hse; Todd F. Shupe

2005-01-01

This study examined the effects of recycled and virgin wood fiber on the properties of fiberboard. Replacing virgin fiber with recycled fiber adversely affected physical and mechanical properties of fiberboard. Bending properties and dimensional stability were linearly dependent on virgin fiber ratios. Based on strength properties, panels with 20 and 40 percent...

Panel established to revise position statement on climate change

NASA Astrophysics Data System (ADS)

President Robert Dickinson has appointed a panel to review the current AGU position statement on climate change and greenhouse gases, and to consider revising the statement to reflect scientific progress over the last four years. Marvin Geller of the State University of New York-Stonybrook chairs the panel.Other panel members include: Andre Berger, George Lemaître Catholic University of Louvain, Belgium; Anny Cazenave, Observatoire Midi-Pyrénées, Toulouse, France; John Christy, University of Alabama, Huntsville; Ellen Druffel, University of California, Irvine; Jack Fellows, University Consortium for Atmospheric Research, Boulder; Hiroshi Kanzawa, Nagoya University, Japan; William Schlesinger, Duke University, Durham; William (Jim) Shuttleworth, University of Arizona; Eric Sundquist, U.S. Geological Survey, Woods Hole; Richard Turco, University of California, Los Angeles; Ilana Wainer, Universidade Cidade Sao Paulo, Brazil.

Testing a Novel Method to Approximate Wood Specific Gravity of Trees

Treesearch

Michael C. Wiemann; G. Bruce Williamson

2012-01-01

Wood specific gravity (SG) has long been used by foresters as an index for wood properties. More recently, SG has been widely used by ecologists as a plant functional trait and as a key variable in estimates of biomass. However, sampling wood to determine SG can be problematic; at present, the most common method is sampling with an increment borer to extract a bark-to-...

Full-scale shear wall tests for force transfer around openings

Treesearch

Tom Skaggs; Borjen Yeh; Frank Lam; Douglas Rammer; James Wacker

2010-01-01

Wood structural panel sheathed shear walls and diaphragms are the primary lateral-load resisting elements in wood-frame construction. The historical performance of light-frame structures in North America are very good due, in part, to model building codes that are designed to preserve life safety, as well as the inherent redundancy of wood-frame construction using wood...

Wood products and other building materials used in new residential construction in Canada, with comparison to previous studies

Treesearch

Joe Elling; David B. McKeever

2015-01-01

New residential construction is a critical driver of the demand for lumber, structural panels and engineered wood products in Canada. For the period 2010 through 2013, residential construction accounted for roughly 23 percent of the lumber consumed in Canada and 47 percent of structural panel usage. Insufficient data concerning imports and exports prevent estimates of...

Pyrolysis kinetics and combustion of thin wood using advanced cone calorimetry test method

Treesearch

Mark A. Dietenberger

2011-01-01

Mechanistic pyrolysis kinetics analysis of extractives, holocellulose, and lignin in solid wood over entire heating regime was possible using specialized cone calorimeter test and new mathematical analysis tools. Added hardware components include: modified sample holder for thin specimen with tiny thermocouples, methane ring burner with stainless steel mesh above cone...

Cone calorimeter testing of foam core sandwich panels treated with intumescent paper underneath the veneer (FRV)

Treesearch

Mark A. Dietenberger; Ali Shalbafan; Johannes Welling

2017-01-01

Surfaces of novel foam core sandwich panels were adhered with intumescent fire‐retardant paper underneath the veneers (FRV) to improve their flammability properties. The panels were evaluated by means of cone calorimeter test (ASTM E 1354). Variables tested were different surface layer treatments, adhesives used for veneering, surface layer thicknesses, and processing...

Factors that lead to failure with wood adhesive bonds

Treesearch

Charles R. Frihart; James F. Beecher

2016-01-01

Understanding what makes a good wood adhesive is difficult since the type of adhesive, wood species, bonding process, and resultant products vary considerably. Wood bonds are subjected to a variety of tests that reflect the different product performance criteria in diverse countries. The most common tests involve some type of moisture resistance; both wood and adhesive...

Low VOC drying of lumber and wood panel products. Progress report Number 9

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, H.; Banerjee, S.; Conners, T.

1999-01-01

Results from a multi-year study show that a significant part of the extensive variability observed in oriented strand board (OSB) flake dryer emissions can be traced to physiological effects, and the rest can be attributed to handling and other factors. Low-headspace treatment of lumber was scaled up to the 50 kg level. The amount of turpentine collected was of the same magnitude as that released upon drying lumber. For the process to be economical, the wood must first be brought to about 95 C with steam, and then processed with RF. Attempts to remove VOCs from OSB through low-headspace bymore » placing a curtain over the wood failed because of leaks. A more rigid container will be required. RF-treatment does not alter the gas permeability of lumber.« less

Design and evaluation of low-cost laminated wood composite blades for intermediate size wind turbines: Blade design, fabrication concept, and cost analysis

NASA Technical Reports Server (NTRS)

Lieblein, S.; Gaugeon, M.; Thomas, G.; Zueck, M.

1982-01-01

As part of a program to reduce wind turbine costs, an evaluation was conducted of a laminated wood composite blade for the Mod-OA 200 kW wind turbine. The effort included the design and fabrication concept for the blade, together with cost and load analyses. The blade structure is composed of laminated Douglas fir veneers for the primary spar and nose sections, and honeycomb cored plywood panels for the trailing edges sections. The attachment of the wood blade to the rotor hub was through load takeoff studs bonded into the blade root. Tests were conducted on specimens of the key structural components to verify the feasibility of the concept. It is concluded that the proposed wood composite blade design and fabrication concept is suitable for Mod-OA size turbines (125-ft diameter rotor) at a cost that is very competitive with other methods of manufacture.

Testing solar panels for small-size satellites: the UPMSAT-2 mission

NASA Astrophysics Data System (ADS)

Roibás-Millán, E.; Alonso-Moragón, A.; Jiménez-Mateos, A. G.; Pindado, S.

2017-11-01

At present, the development of small-size satellites by universities, companies and research institutions has become usual practice, and is spreading rapidly. In this kind of project cost plays a significant role. One of the main areas are the assembly, integration and test (AIT) plans, which carry an associated cost for simulating environmental conditions. For instance, in the power subsystems test and, in particular, in the testing of solar panels, the irradiance and temperature conditions might be optimum so the performance of the system can be shown next to real operational conditions. To reproduce the environmental conditions in terms of irradiance, solar simulators are usually used, which carries an associated increase in cost for testing the equipment. The aim of this paper is to present an alternative and inexpensive way to perform AIT plans on spacecraft power subsystems, from a testing campaign performed using outdoor clean-sky conditions and an isolation system to protect the panels. A post-process of the measured data is therefore needed, taking into account the conditions in which the test has been accomplished. The I-V characteristics obtained are compared with a theoretical 1-diode/2-resistor equivalent electric circuit, achieving enough precision based solely on the manufacturer’s data.

Effects of tree species and wood particle size on the properties of cement-bonded particleboard manufacturing from tree prunings.

PubMed

Nasser, Ramadan A; Al-Mefarrej, H A; Abdel-Aal, M A; Alshahrani, T S

2014-09-01

This study investigated the possibility of using the prunings of six locally grown tree species in Saudi Arabia for cement-bonded particleboard (CBP) production. Panels were made using four different wood particle sizes and a constant wood/cement ratio (1/3 by weight) and target density (1200 kg/m3). The mechanical properties and dimensional stability of the produced panels were determined. The interfacial area and distribution of the wood particles in cement matrix were also investigated by scanning electron microscopy. The results revealed that the panels produced from these pruning materials at a target density of 1200 kg m(-3) meet the strength and dimensional stability requirements of the commercial CBP panels. The mean moduli of rupture and elasticity (MOR and MOE) ranged from 9.68 to 11.78 N mm2 and from 3952 to 5667 N mm2, respectively. The mean percent water absorption for twenty four hours (WA24) ranged from 12.93% to 23.39%. Thickness swelling values ranged from 0.62% to 1.53%. For CBP panels with high mechanical properties and good dimensional stability, mixed-size or coarse particles should be used. Using the tree prunings for CBPs production may help to solve the problem of getting rid of these residues by reducing their negative effects on environment, which are caused by poor disposal of such materials through direct combustion process and appearance of black cloud and then the impact on human health or the random accumulation and its indirect effects on the environment.

Fabrication and testing of fire resistant graphite composite panels

NASA Technical Reports Server (NTRS)

Roper, W. D.

1986-01-01

Eight different graphite composite panels were fabricated using four different resin matrices. The resin matrices included Hercules 71775, a blend of vinylpolystyrpyridine and bismaleimide, H795, a bismaleimide, Cycom 6162, a phenolic, and PSP 6022m, a polystyrylpyridine. Graphite panels were fabricated using fabric or unidirectional tape. Described are the processes for preparing these panels and some of their mechanical, thermal and flammability properties. Panel properties are compared with state-of-the-art epoxy fiberglass composite panels.

Microbial Community Analysis of Naturally Durable Wood in an Above Ground Field Test

Treesearch

G.T. Kirker; S.V. Diehl; P.K. Lebow

2014-01-01

This paper presents preliminary results of an above ground field test wherein eight naturally durable wood species were exposed concurrently at two sites in North America. Surface samples were taken at regular intervals from non-durable controls and compared to their more durable counterparts. Terminal Restriction Fragment Length Polymorphism was performed to...

Toxicity of chromated copper arsenate (CCA)-treated wood to non-target marine fouling communities in Langstone Harbour, Portsmouth, UK.

PubMed

Brown, C J; Eaton, R A

2001-04-01

The effect of the anti-marine-borer timber preservative chromated copper arsenate (CCA) (a pressure impregnated solution of copper, chromium and arsenic compounds) on non-target marine fouling animals was investigated during a subtidal exposure trial. Panels of Scots pine treated to target retentions of 12, 24 and 48 kg CCA per m-3 of wood, plus untreated controls were submerged at a coastal site on the south coast of the UK for 6, 12 and 18 months. After each exposure period the fouling communities that formed on the surface of panels were assessed both qualitatively and quantitatively. Community structure was similar on panels treated to the three CCA loadings, but was significantly different from community structure on untreated panels. The total number of species (species richness) was similar on all panels, although the number of individual organisms attached to the surface of panels was significantly higher on CCA-treated panels than on untreated panels. k-dominance curves revealed that the difference in numbers of individuals between CCA-treated and untreated panels was caused by higher numbers of the dominant species (Elminius modestus, Hydroides ezoensis, and Electra pilosa) on CCA-treated panels. Other species were present in similar numbers on panels of all treatments. Results indicate that there are no detrimental toxic effects to epibiota caused by the presence of CCA preservative within the matrix of the wood at any of the treatment levels. Differences in community structure between CCA-treated and untreated panels may be due to enhanced larval settlement on CCA-treated timber by some species as a result of modifications to the surface properties of the timber by the CCA preservative.

Evaluation of Precast Panels for Airfield Pavement Repair. Phase 2: Results of Accelerated Pavement Testing

DTIC Science & Technology

2013-09-01

ER D C/ G SL T R -1 3 -2 4 Evaluation of Precast Panels for Airfield Pavement Repair Phase II: Results of Accelerated Pavement Testing...default. ERDC/GSL TR-13-24 September 2013 Evaluation of Precast Panels for Airfield Pavement Repair Phase II: Results of Accelerated Pavement ... pavement testing using a C-17 load cart to evaluate the performance of a precast portland cement concrete (PCC) pavement repair system. The system

HRR Upgrade to mass loss calorimeter and modified Schlyter test for FR Wood

Treesearch

Mark A. Dietenberger; Charles R. Boardman

2013-01-01

Enhanced Heat Release Rate (HRR) methodology has been extended to the Mass Loss Calorimeter (MLC) and the Modified Schlyter flame spread test to evaluate fire retardant effectiveness used on wood based materials. Modifications to MLC include installation of thermopile on the chimney walls to correct systematic errors to the sensible HRR calculations to account for...

Composite panel development at JPL

NASA Technical Reports Server (NTRS)

Mcelroy, Paul; Helms, Rich

1988-01-01

Parametric computer studies can be use in a cost effective manner to determine optimized composite mirror panel designs. An InterDisciplinary computer Model (IDM) was created to aid in the development of high precision reflector panels for LDR. The materials properties, thermal responses, structural geometries, and radio/optical precision are synergistically analyzed for specific panel designs. Promising panels designs are fabricated and tested so that comparison with panel test results can be used to verify performance prediction models and accommodate design refinement. The iterative approach of computer design and model refinement with performance testing and materials optimization has shown good results for LDR panels.

Authenticated DNA from Ancient Wood Remains

PubMed Central

LIEPELT, SASCHA; SPERISEN, CHRISTOPH; DEGUILLOUX, MARIE-FRANCE; PETIT, REMY J.; KISSLING, ROY; SPENCER, MATTHEW; DE BEAULIEU, JACQUES-LOUIS; TABERLET, PIERRE; GIELLY, LUDOVIC; ZIEGENHAGEN, BIRGIT

2006-01-01

• Background The reconstruction of biological processes and human activities during the last glacial cycle relies mainly on data from biological remains. Highly abundant tissues, such as wood, are candidates for a genetic analysis of past populations. While well-authenticated DNA has now been recovered from various fossil remains, the final ‘proof’ is still missing for wood, despite some promising studies. • Scope The goal of this study was to determine if ancient wood can be analysed routinely in studies of archaeology and palaeogenetics. An experiment was designed which included blind testing, independent replicates, extensive contamination controls and rigorous statistical tests. Ten samples of ancient wood from major European forest tree genera were analysed with plastid DNA markers. • Conclusions Authentic DNA was retrieved from wood samples up to 1000 years of age. A new tool for real-time vegetation history and archaeology is ready to use. PMID:16987920

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

NASA Technical Reports Server (NTRS)

Frady, Gregory P.; Duvall, Lowery D.; Fulcher, Clay W. G.; Laverde, Bruce T.; Hunt, Ronald A.

2011-01-01

A rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for a curved orthogrid panel typical of launch vehicle skin structures. Several test article configurations were produced by adding component equipment of differing weights to the flight-like vehicle panel. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was employed to describe the assumed correlation of phased input sound pressures across the energized panel. This application demonstrates the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software modules developed for the RPTF method can be easily adapted for

EXAMINING EVIDENCE IN U.S. PAYER COVERAGE POLICIES FOR MULTI-GENE PANELS AND SEQUENCING TESTS.

PubMed

Chambers, James D; Saret, Cayla J; Anderson, Jordan E; Deverka, Patricia A; Douglas, Michael P; Phillips, Kathryn A

2017-01-01

The aim of this study was to examine the evidence payers cited in their coverage policies for multi-gene panels and sequencing tests (panels), and to compare these findings with the evidence payers cited in their coverage policies for other types of medical interventions. We used the University of California at San Francisco TRANSPERS Payer Coverage Registry to identify coverage policies for panels issued by five of the largest US private payers. We reviewed each policy and categorized the evidence cited within as: clinical studies, systematic reviews, technology assessments, cost-effectiveness analyses (CEAs), budget impact studies, and clinical guidelines. We compared the evidence cited in these coverage policies for panels with the evidence cited in policies for other intervention types (pharmaceuticals, medical devices, diagnostic tests and imaging, and surgical interventions) as reported in a previous study. Fifty-five coverage policies for panels were included. On average, payers cited clinical guidelines in 84 percent of their coverage policies (range, 73-100 percent), clinical studies in 69 percent (50-87 percent), technology assessments 47 percent (33-86 percent), systematic reviews or meta-analyses 31 percent (7-71 percent), and CEAs 5 percent (0-7 percent). No payers cited budget impact studies in their policies. Payers less often cited clinical studies, systematic reviews, technology assessments, and CEAs in their coverage policies for panels than in their policies for other intervention types. Payers cited clinical guidelines in a comparable proportion of policies for panels and other technology types. Payers in our sample less often cited clinical studies and other evidence types in their coverage policies for panels than they did in their coverage policies for other types of medical interventions.

Nondestructive Evaluation of Wood: Second Edition

Treesearch

Robert J. Ross

2015-01-01

This report summarizes information on nondestructive testing and evaluation of wood. It includes information on a wide range of nondestructive assessment technologies and their uses for evaluating various wood products.

Effects of Acid Deposition on Wood

Treesearch

Mark Knaebe

2013-01-01

Since acid deposition increases the rate of deterioration of unpainted wood, it can also affect the performance of paint applied to this weathered wood. In tests conducted near Madison, Wisconsin, smooth-planed wood was allowed to weather before painting. Exposure for as little as 2 weeks shortened the service life of the subsequently applied paint. The paint bond was...

Wood handbook : wood as an engineering material.

Treesearch

Forest Products Laboratory

1999-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Wood handbook : wood as an engineering material

Treesearch

Robert J. Ross; Forest Products Laboratory USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

A research program to reduce interior noise in general aviation airplanes: Investigation of the characteristics of an acoustic panel test facility

NASA Technical Reports Server (NTRS)

Grosveld, F.; Vanaken, J.

1978-01-01

Sound pressure levels in the test facility were studied that are caused by varying: (1) microphone positions; (2) equalizer setting; and (3) panel clamping forces. Measurements were done by using a Beranek tube or this Beranek tube in combinations with an extension tube and a special test section. In all configurations tests were executed with and without a test panel installed. The influence of the speaker back panel and the back panel of the Beranek tube on the sound pressure levels inside the test tube were also investigated. It is shown that the definition of noise reduction is more useful in relation to this test facility than transmission loss.

Analysis of Global Ultrasonic Sensor Data from a Full Scale Wing Panel Test

NASA Astrophysics Data System (ADS)

Michaels, Jennifer E.; Michaels, Thomas E.; Martin, Ramaldo S.

2009-03-01

A full scale wing panel fatigue test was undertaken in 2007 as a part of the DARPA Structural Integrity Prognosis System (SIPS) program. Both local and global ultrasonic sensors were installed on the wing panel and data were recorded periodically over a period of about seven weeks. The local ultrasonic sensors interrogated a small number of selected fastener holes, and the global ultrasonic sensors were arranged in a spatially distributed array surrounding an area encompassing multiple fastener holes of interest. The global ultrasonic sensor data is the focus of the work reported here. Waveforms were recorded from all pitch-catch sensor pairs as a function of static load while fatiguing was paused. The time windows over which the waveforms were recorded were long enough to include most of the reverberating energy. Partway through the test simulated defects were temporarily introduced by gluing masses onto the surface of the wing panel, and waveforms were recorded immediately before their attachment and after their removal. The overall fatigue test was terminated while cracks originating from the fastener holes were still relatively small and before they reached the surface of the wing panel. Both detection and localization results are shown for the artificial damage, and the overall repeatability and stability of the signals are analyzed. Also shown is an analysis of how the reverberating signals change as a function of applied load. The fastener hole fatigue cracks were not detected by the global transducer array, which is not surprising given the final sizes of the cracks as determined by later destructive analysis. However, signals were stable throughout the entire fatigue test, and effects of load on the received signals were significant, both in the short-time and long-time signal regimes.

Test and analysis of a stitched RFI graphite-epoxy panel with a fuel access door

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.; Waters, W. Allen, Jr.

1994-01-01

A stitched RFI graphite-epoxy panel with a fuel access door was analyzed using a finite element analysis and loaded to failure in compression. The panel was initially 56-inches long and 36.75-inches wide and the oval access door was 18-inches long and 15-inches wide. The panel was impact damaged with impact energy of 100 ft-lb prior to compressive loading; however, no impact damage was detectable visually or by A-scan. The panel carried a failure load of 695,000 Ib and global failure strain of .00494 in/in. Analysis indicated the panel would fail due to collapse at a load of 688,100 Ib. The test data indicate that the maximum strain in a region near the access door was .0096 in/in and analysis indicates a local surface strain of .010 in/in at the panel's failure load. The panel did not fail through the impact damage, but instead failed through bolt holes for attachment of the access door in a region of high strain.

Laser welded steel sandwich panel bridge deck development : finite element analysis and stake weld strength tests.

DOT National Transportation Integrated Search

2009-09-01

This report summarizes the analysis of laser welded steel sandwich panels for use in bridge structures and : static testing of laser stake welded lap shear coupons. Steel sandwich panels consist of two face sheets : connected by a relatively low-dens...

Rice straw-wood particle composite for sound absorbing wooden construction materials.

PubMed

Yang, Han-Seung; Kim, Dae-Jun; Kim, Hyun-Joong

2003-01-01

In this study, rice straw-wood particle composite boards were manufactured as insulation boards using the method used in the wood-based panel industry. The raw material, rice straw, was chosen because of its availability. The manufacturing parameters were: a specific gravity of 0.4, 0.6, and 0.8, and a rice straw content (10/90, 20/80, and 30/70 weight of rice straw/wood particle) of 10, 20, and 30 wt.%. A commercial urea-formaldehyde adhesive was used as the composite binder, to achieve 140-290 psi of bending modulus of rupture (MOR) with 0.4 specific gravity, 700-900 psi of bending MOR with 0.6 specific gravity, and 1400-2900 psi of bending MOR with a 0.8 specific gravity. All of the composite boards were superior to insulation board in strength. Width and length of the rice straw particle did not affect the bending MOR. The composite boards made from a random cutting of rice straw and wood particles were the best and recommended for manufacturing processes. Sound absorption coefficients of the 0.4 and 0.6 specific gravity boards were higher than the other wood-based materials. The recommended properties of the rice straw-wood particle composite boards are described, to absorb noises, preserve the temperature of indoor living spaces, and to be able to partially or completely substitute for wood particleboard and insulation board in wooden constructions.

New views on antidiarrheal effect of wood creosote: is wood creosote really a gastrointestinal antiseptic?

PubMed

Ataka, Koji; Ito, Masafumi; Shibata, Takashi

2005-12-01

Wood creosote, the principal ingredient in Seirogan, has a long history as a known gastrointestinal microbicidal agent. When administered orally, the intraluminal concentration of wood creosote is not sufficiently high to achieve this microbicidal effect. Through further animal tests, we have shown that antimotility and antisecretory actions are the principal antidiarrheal effects of wood creosote. Wood creosote inhibits intestinal secretion induced by enterotoxins by blocking the Cl(-) channel on the intestinal epithelium. Wood creosote also decreases intestinal motility accelerated by mechanical, chemical, or electrical stimulus by the inhibition of the Ca(2+) influx into the smooth muscle cells. In this overview, the antimotility and antisecretory effects of wood creosote are compared with those of loperamide. Wood creosote was observed to inhibit stimulated colonic motility, but not normal jejunal motility. Loperamide inhibits normal jejunal motility, but not stimulated colonic motility. Both wood creosote and loperamide inhibit intestinal secretion accelerated by acetylcholine. Wood creosote was found to have greater antisecretory effects in the colon than loperamide. Based upon these findings, we conclude that the antidiarrheal effects of wood creosote are due to both antisecretory activity in the intestine and antimotility in the colon, but not due to the microbicidal activity as previously thought. Wood creosote was found to have no effects on normal intestinal activity. These conclusions are supported by the results of a recent clinical study comparing wood creosote and loperamide, which concluded that wood creosote was more efficacious in relieving abdominal pain and comparable to loperamide in relieving diarrhea.

EXAMINING EVIDENCE IN U.S. PAYER COVERAGE POLICIES FOR MULTI-GENE PANELS AND SEQUENCING TESTS

PubMed Central

Chambers, James D.; Saret, Cayla J.; Anderson, Jordan E.; Deverka, Patricia A.; Douglas, Michael P.; Phillips, Kathryn A.

2017-01-01

Objectives The aim of this study was to examine the evidence payers cited in their coverage policies for multi-gene panels and sequencing tests (panels), and to compare these findings with the evidence payers cited in their coverage policies for other types of medical interventions. Methods We used the University of California at San Francisco TRANSPERS Payer Coverage Registry to identify coverage policies for panels issued by five of the largest US private payers. We reviewed each policy and categorized the evidence cited within as: clinical studies, systematic reviews, technology assessments, cost-effectiveness analyses (CEAs), budget impact studies, and clinical guidelines. We compared the evidence cited in these coverage policies for panels with the evidence cited in policies for other intervention types (pharmaceuticals, medical devices, diagnostic tests and imaging, and surgical interventions) as reported in a previous study. Results Fifty-five coverage policies for panels were included. On average, payers cited clinical guidelines in 84 percent of their coverage policies (range, 73–100 percent), clinical studies in 69 percent (50–87 percent), technology assessments 47 percent (33–86 percent), systematic reviews or meta-analyses 31 percent (7–71 percent), and CEAs 5 percent (0–7 percent). No payers cited budget impact studies in their policies. Payers less often cited clinical studies, systematic reviews, technology assessments, and CEAs in their coverage policies for panels than in their policies for other intervention types. Payers cited clinical guidelines in a comparable proportion of policies for panels and other technology types. Conclusions Payers in our sample less often cited clinical studies and other evidence types in their coverage policies for panels than they did in their coverage policies for other types of medical interventions. PMID:29065945

Laser processing of phenolic wood substitutes

NASA Astrophysics Data System (ADS)

Quintero, F.; Riveiro, A.; Lusquiños, F.; Penide, J.; Arias-González, F.; del Val, J.; Comesaña, R.; Boutinguiza, M.; Pou, J.

2013-11-01

Phenolic resin boards (PRB) are wood substitutes that comprises of a thick core exclusively made of phenolic resin covered by a thin sheet of melamine resin imitating the aspect of natural wood. The use of these materials in furniture and in construction industry has proliferated during last years. Boards made of phenolic resins are dense, hard and very difficult to cut using band saws, disc saws, or milling cutters. Nevertheless, these difficulties can be overcome by means of laser cutting, which is one of the most firmly established techniques for separating materials. This is due to the great advantages of this technique over traditional cutting methods, such as its versatility and flexibility that allow effective cutting. Nevertheless, charring of the cut edge surface caused by laser induced thermal degradation degrades the cut quality under non-optimized processing conditions. In this research work the viability and quality of CO2 laser cutting process of phenolic resin boards and wood particleboard panels has been evaluated. The present work validates the cut of phenolic resin boards by CO2 lasers using a high laser power and elevated cutting speeds. Moreover, this process involves a serious health hazard since the combustion and decomposition of wood may produce fumes and vapors, which can be toxic and carcinogenic according to the International Chemical Safety Cards (ICSC). Therefore, this work was complemented by the assessment of the potential toxicity of the condensed residues formed on the cut edges, and assessment of the chemistry of the generated fumes by chromatography.

Field performance testing of improved engineered wood fiber surfaces for accessible playground areas

Treesearch

Theodore L. Laufenberg; Jerrold E. Winandy

2003-01-01

Some engineered wood fiber (EWF) surfaces on playgrounds are soft and uneven, which creates difficulties for those who use mobility aids, such as wheelchairs and walkers. The outdoor field testing reported in this study is part of an effort to stabilize EWF to improve accessibility. The concept is to mix a binder with the upper surface of EWF to create a stiff (firm)...

Subscale Testing of a Ceramic Composite Cooled Panel Led to Its Design and Fabrication for Scramjet Engine Testing

NASA Technical Reports Server (NTRS)

Jaskowiak, Martha H.

2004-01-01

In a partnership between the NASA Glenn Research Center and Pratt & Whitney, a ceramic heat exchanger panel intended for use along the hot-flow-path walls of future reusable launch vehicles was designed, fabricated, and tested. These regeneratively cooled ceramic matrix composite (CMC) panels offer lighter weight, higher operating temperatures, and reduced coolant requirements in comparison to their more traditional metallic counterparts. A maintainable approach to the design was adopted which allowed the panel components to be assembled with high-temperature fasteners rather than by permanent bonding methods. With this approach, the CMC hot face sheet, the coolant containment system, and backside structure were all fabricated separately and could be replaced individually as the need occurred during use. This maintainable design leads to both ease of fabrication and reduced cost.

Construction of low-cost, Mod-OA wood composite wind turbine blades

NASA Technical Reports Server (NTRS)

Lark, R. F.

1983-01-01

Two sixty-foot, low-cost, wood composite blades for service on 200 kW Mod-OA wind turbines were constructed. The blades were constructed of epoxy resin-bonded Douglas fir veneers for the leading edge sections, and paper honeycombcored, birch plywood faced panels for the afterbody sections. The blades were joined to the wind turbine hub by epoxy resin-bonded steel load take-off studs embedded into the root end of the blades. The blades were installed on the 200 kW Mod-OA wind turbine facility at Kahuku, Hawaii, The blades completed nearly 8,000 hours of operation over an 18 month period at an average power of 150 kW prior to replacement with another set of wood composite blades. The blades were replaced because of a corrosion failure of the steel shank on one stud. Inspections showed that the wood composite structure remained in excellent condition.

Wood : adhesives

Treesearch

A.H. Conner

2001-01-01

This chapter on wood adhesives includes: 1) Classification of wood adhesives 2) Thermosetting wood adhesives 3) Thermoplastic adhesives, 4) Wood adhesives based on natural sources 5) Nonconventional bonding of wood 6) Wood bonding.

Adhesives for assembly of lightweight wood containers

Treesearch

R. S. Kurtenacker

1964-01-01

This report discusses the screening of various adhesive and mastic systems for possible use in assembling lightweight wood containers. Results showed that dynamic tests of simulated box corners correlated reasonably well with rough handling evaluations of eight selected systems when used to assemble lightweight wood boxes made from a Group I container wood....

Lightweight composites for modular panelized construction

NASA Astrophysics Data System (ADS)

Vaidya, Amol S.

Rapid advances in construction materials technology have enabled civil engineers to achieve impressive gains in the safety, economy, and functionality of structures built to serve the common needs of society. Modular building systems is a fast-growing modern, form of construction gaining recognition for its increased efficiency and ability to apply modern technology to the needs of the market place. In the modular construction technique, a single structural panel can perform a number of functions such as providing thermal insulation, vibration damping, and structural strength. These multifunctional panels can be prefabricated in a manufacturing facility and then transferred to the construction site. A system that uses prefabricated panels for construction is called a "panelized construction system". This study focuses on the development of pre-cast, lightweight, multifunctional sandwich composite panels to be used for panelized construction. Two thermoplastic composite panels are proposed in this study, namely Composite Structural Insulated Panels (CSIPs) for exterior walls, floors and roofs, and Open Core Sandwich composite for multifunctional interior walls of a structure. Special manufacturing techniques are developed for manufacturing these panels. The structural behavior of these panels is analyzed based on various building design codes. Detailed descriptions of the design, cost analysis, manufacturing, finite element modeling and structural testing of these proposed panels are included in this study in the of form five peer-reviewed journal articles. The structural testing of the proposed panels involved in this study included flexural testing, axial compression testing, and low and high velocity impact testing. Based on the current study, the proposed CSIP wall and floor panels were found satisfactory, based on building design codes ASCE-7-05 and ACI-318-05. Joining techniques are proposed in this study for connecting the precast panels on the construction

MTR WING, TRA604. PRECAST CONCRETE PANELS AND DIMENSIONS FOR PANELS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MTR WING, TRA-604. PRECAST CONCRETE PANELS AND DIMENSIONS FOR PANELS K THROUGH Q. BLAW-KNOX 3150-804-21, SHEET #2, 11/1950. INL INDEX NO. 531-0604-62-098-100645, REV. 2. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

Feasibility of producing value-added wood products from reclaimed hemlock lumber

Treesearch

John J. Janowiak; Robert H. Falk; Jeffery D. Kimmel

2007-01-01

This study evaluated the feasibility of producing value-added wood products from hemlock lumber salvaged from building deconstruction. About 6,000 board feet of lumber, ranging in size from 3 in. by 8 in. to 3 in. by 12 in., was remilled into four products including log cabin siding, V-groove paneling, beadboard (wainscoting), and tongue and groove flooring. The...

12. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN FOURPANEL WOOD DOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. INTERIOR OF KITCHEN/UTILITY AREA SHOWING OPEN FOUR-PANEL WOOD DOOR TO SOUTH BEDROOM AT PHOTO CENTER RIGHT, OPEN DOORWAY TO LIVING ROOM AT PHOTO CENTER LEFT, AND BUILT-IN CABINETS AND CEILING VENT BETWEEN THE DOORS AND AROUND THE STOVE/RANGE POSITION. VIEW TO NORTHEAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Antinuclear antibody panel

MedlinePlus

... ANA panel; ANA reflexive panel; SLE - ANA; Systemic lupus erythematosus - ANA ... have signs of an autoimmune disorder, particularly systemic lupus erythematosus . This test may be done if you ...

Testing and Analysis Validation of a Metallic Repair Applied to a PRSEUS Tension Panel

NASA Technical Reports Server (NTRS)

Przekop, Adam; Jegley, Dawn C.

2013-01-01

A design and analysis of a repair concept applicable to a stiffened composite panel based on the Pultruded Rod Stitched Efficient Unitized Structure was recently completed. The damage scenario considered was a midbay-to-midbay saw-cut with a severed stiffener, flange and skin. Advanced modeling techniques such as mesh-independent definition of compliant fasteners and elastic-plastic material properties for metal parts were utilized in the finite element analysis supporting the design effort. A bolted metallic repair was selected so that it could be easily applied in the operational environment. The present work describes results obtained from a tension panel test conducted to validate both the repair concept and finite element analysis techniques used in the design effort. The test proved that the proposed repair concept is capable of sustaining load levels that are higher than those resulting from the current working stress allowables. This conclusion enables upward revision of the stress allowables that had been kept at an overly-conservative level due to concerns associated with repairability of the panels. Correlation of test data with finite element analysis results is also presented and assessed.

Detailed analysis and test correlation of a stiffened composite wing panel

NASA Technical Reports Server (NTRS)

Davis, D. Dale, Jr.

1991-01-01

Nonlinear finite element analysis techniques are evaluated by applying them to a realistic aircraft structural component. A wing panel from the V-22 tiltrotor aircraft is chosen because it is a typical modern aircraft structural component for which there is experimental data for comparison of results. From blueprints and drawings supplied by the Bell Helicopter Textron Corporation, a very detailed finite element model containing 2284 9-node Assumed Natural-Coordinate Strain (ANS) elements was generated. A novel solution strategy which accounts for geometric nonlinearity through the use of corotating element reference frames and nonlinear strain displacements relations is used to analyze this detailed model. Results from linear analyses using the same finite element model are presented in order to illustrate the advantages and costs of the nonlinear analysis as compared with the more traditional linear analysis. Strain predictions from both the linear and nonlinear stress analyses are shown to compare well with experimental data up through the Design Ultimate Load (DUL) of the panel. However, due to the extreme nonlinear response of the panel, the linear analysis was not accurate at loads above the DUL. The nonlinear analysis more accurately predicted the strain at high values of applied load, and even predicted complicated nonlinear response characteristics, such as load reversals, at the observed failure load of the test panel. In order to understand the failure mechanism of the panel, buckling and first ply failure analyses were performed. The buckling load was 17 percent above the observed failure load while first ply failure analyses indicated significant material damage at and below the observed failure load.

Nondestructive testing methods to predict effect of degradation on wood : a critical assessment

Treesearch

J. Kaiserlik

1978-01-01

Results are reported for an assessment of methods for predicting strength of wood, wood-based, or related material. Research directly applicable to nondestructive strength prediction was very limited. In wood, strength prediction research is limited to vibration decay, wave attenuation, and multiparameter "degradation models." Nonwood methods with potential...

Test-Anchored Vibration Response Predictions for an Acoustically Energized Curved Orthogrid Panel with Mounted Components

NASA Technical Reports Server (NTRS)

Frady, Gregory P.; Duvall, Lowery D.; Fulcher, Clay W. G.; Laverde, Bruce T.; Hunt, Ronald A.

2011-01-01

rich body of vibroacoustic test data was recently generated at Marshall Space Flight Center for component-loaded curved orthogrid panels typical of launch vehicle skin structures. The test data were used to anchor computational predictions of a variety of spatially distributed responses including acceleration, strain and component interface force. Transfer functions relating the responses to the input pressure field were generated from finite element based modal solutions and test-derived damping estimates. A diffuse acoustic field model was applied to correlate the measured input sound pressures across the energized panel. This application quantifies the ability to quickly and accurately predict a variety of responses to acoustically energized skin panels with mounted components. Favorable comparisons between the measured and predicted responses were established. The validated models were used to examine vibration response sensitivities to relevant modeling parameters such as pressure patch density, mesh density, weight of the mounted component and model form. Convergence metrics include spectral densities and cumulative root-mean squared (RMS) functions for acceleration, velocity, displacement, strain and interface force. Minimum frequencies for response convergence were established as well as recommendations for modeling techniques, particularly in the early stages of a component design when accurate structural vibration requirements are needed relatively quickly. The results were compared with long-established guidelines for modeling accuracy of component-loaded panels. A theoretical basis for the Response/Pressure Transfer Function (RPTF) approach provides insight into trends observed in the response predictions and confirmed in the test data. The software developed for the RPTF method allows easy replacement of the diffuse acoustic field with other pressure fields such as a turbulent boundary layer (TBL) model suitable for vehicle ascent. Structural responses

Damage Assessment of a Full-Scale Six-Story wood-frame Building Following Triaxial shake Table Tests

Treesearch

John W. van de Lindt; Rakesh Gupta; Shiling Pei; Kazuki Tachibana; Yasuhiro Araki; Douglas Rammer; Hiroshi Isoda

2012-01-01

In the summer of 2009, a full-scale midrise wood-frame building was tested under a series of simulated earthquakes on the world's largest shake table in Miki City, Japan. The objective of this series of tests was to validate a performance-based seismic design approach by qualitatively and quantitatively examining the building's seismic performance in terms of...

2014 Consensus conference on viscoelastic test-based transfusion guidelines for early trauma resuscitation: Report of the panel.

PubMed

Inaba, Kenji; Rizoli, Sandro; Veigas, Precilla V; Callum, Jeannie; Davenport, Ross; Hess, John; Maegele, Marc

2015-06-01

There has been an increased interest in the use of viscoelastic testing to guide blood product replacement during the acute resuscitation of the injured patient. Currently, no uniformly accepted guidelines exist for how this technology should be integrated into clinical care. In September 2014, an international multidisciplinary group of leaders in the field of trauma coagulopathy and resuscitation was assembled for a 2-day consensus conference in Philadelphia, Pennsylvania. This panel included trauma surgeons, hematologists, blood bank specialists, anesthesiologists, and the lay public.Nine questions regarding the impact of viscoelastic testing in the early resuscitation of trauma patients were developed before the conference by panel consensus. Early use was defined as baseline viscoelastic test result thresholds obtained within the first minutes of hospital arrival-when conventional laboratory results are not available. The available data for each question were then reviewed in person using standardized presentations by the expert panel. A consensus summary document was then developed and reviewed by the panel in an open forum. Finally, a two-round Delphi poll was administered to the panel of experts regarding viscoelastic thresholds for triggering the initiation of specific treatments including fibrinogen, platelets, plasma, and prothrombin complex concentrates. This report summarizes the findings and recommendations of this consensus conference.

A study to ascertain the viability of ultrasonic nondestructive testing to determine the mechanical characteristics of wood/agricultural hardboards with soybean based adhesives

NASA Astrophysics Data System (ADS)

Colen, Charles Raymond, Jr.

There have been numerous studies with ultrasonic nondestructive testing and wood fiber composites. The problem of the study was to ascertain whether ultrasonic nondestructive testing can be used in place of destructive testing to obtain the modulus of elasticity (MOE) of the wood/agricultural material with comparable results. The uniqueness of this research is that it addressed the type of content (cornstalks and switchgrass) being used with the wood fibers and the type of adhesives (soybean-based) associated with the production of these composite materials. Two research questions were addressed in the study. The major objective was to determine if one can predict the destructive test MOE value based on the nondestructive test MOE value. The population of the study was wood/agricultural fiberboards made from wood fibers, cornstalks, and switchgrass bonded together with soybean-based, urea-formaldehyde, and phenol-formaldehyde adhesives. Correlational analysis was used to determine if there was a relationship between the two tests. Regression analysis was performed to determine a prediction equation for the destructive test MOE value. Data were collected on both procedures using ultrasonic nondestructing testing and 3-point destructive testing. The results produced a simple linear regression model for this study which was adequate in the prediction of destructive MOE values if the nondestructive MOE value is known. An approximation very close to the entire error in the model equation was explained from the destructive test MOE values for the composites. The nondestructive MOE values used to produce a linear regression model explained 83% of the variability in the destructive test MOE values. The study also showed that, for the particular destructive test values obtained with the equipment used, the model associated with the study is as good as it could be due to the variability in the results from the destructive tests. In this study, an ultrasonic signal was used

Nondestructive and Strain Testing of Composite Sandwich Panels

NASA Astrophysics Data System (ADS)

Goyings, Ryan

In April 2006, Sikorsky Aircraft received a contract from the United States Marine Corps (USMC) to develop a successor to their CH-53E heavy-lift helicopter. The new designation is the CH-53K "Super Stallion" and provides increased operating capabilities through the use of design revisions that incorporate extensive use of carbon fiber composites and composite sandwich panels. "The CH-53K will have five times the capability at half of the operational cost of the aircraft it's replacing. It will be the most capable helicopter ever produced. With more than twice the combat radius of the CH-53E, the CH-53K uses mature technology to deliver a fully shipboard compatible platform to meet current and future Marine Corps requirements". Upon introduction, it will be the largest rotary wing aircraft in the United States Department of Defense. The USMC will incorporate the CH-53K into the Joint Operations Concept of Full Spectrum Dominance and Sea Power 21 thereby enabling rapid, decisive operations and the early termination of conflict by projecting and sustaining forces to distant anti-access, area-denial environments. Even with an increased lift capability, the CH-53K is a slow moving, low flying helicopter susceptible to damage from small arms fire. There is no field level composite repair capability within any maintained documents published by the Department of Defense. Purdue University has developed a field level rapid repair technique capable of returning strength and integrity to damaged carbon composite structural components. The patch is made from carbon fiber weave that is applied using a field capable Vacuum Assisted Resin Transfer Molding (VARTM). This thesis seeks to validate, using nondestructive testing methods and strain monitoring, the manufacturing, damage, and repair process of composite sandwich panels representative of the CH-53K structural panels.

Water repellency and dimensional stability of wood

Treesearch

Roger M. Rowell; W. Bart Banks

1985-01-01

A discussion of the interaction between wood and water makes clear the distinction between water repellency of wood (a rate of change) and dimensional stability (a level of equilibrium). A review of methods of treating wood follows, leading to comparison of their effectiveness, description of test procedures to evaluate treatments, and discussion of deficiencies of the...

21 CFR 610.44 - Use of reference panels by manufacturers of test kits.

Code of Federal Regulations, 2012 CFR

2012-04-01

... kits. 610.44 Section 610.44 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Disease Agents § 610.44 Use of reference panels by manufacturers of test kits. (a) When available and appropriate to verify acceptable sensitivity and specificity, you, a manufacturer of test kits, must use a...

21 CFR 610.44 - Use of reference panels by manufacturers of test kits.

Code of Federal Regulations, 2014 CFR

2014-04-01

... kits. 610.44 Section 610.44 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Disease Agents § 610.44 Use of reference panels by manufacturers of test kits. (a) When available and appropriate to verify acceptable sensitivity and specificity, you, a manufacturer of test kits, must use a...

21 CFR 610.44 - Use of reference panels by manufacturers of test kits.

Code of Federal Regulations, 2013 CFR

2013-04-01

... kits. 610.44 Section 610.44 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Disease Agents § 610.44 Use of reference panels by manufacturers of test kits. (a) When available and appropriate to verify acceptable sensitivity and specificity, you, a manufacturer of test kits, must use a...

21 CFR 610.44 - Use of reference panels by manufacturers of test kits.

Code of Federal Regulations, 2011 CFR

2011-04-01

... kits. 610.44 Section 610.44 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Disease Agents § 610.44 Use of reference panels by manufacturers of test kits. (a) When available and appropriate to verify acceptable sensitivity and specificity, you, a manufacturer of test kits, must use a...

21 CFR 610.44 - Use of reference panels by manufacturers of test kits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... kits. 610.44 Section 610.44 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Disease Agents § 610.44 Use of reference panels by manufacturers of test kits. (a) When available and appropriate to verify acceptable sensitivity and specificity, you, a manufacturer of test kits, must use a...

Test and Analysis of Foam Impacting a 6x6 Inch RCC Flat Panel

NASA Technical Reports Server (NTRS)

Lessard, Wendy B.

2006-01-01

This report presents the testing and analyses of a foam projectile impacting onto thirteen 6x6 inch flat panels at a 90 degrees incidence angle. The panels tested in this investigation were fabricated of Reinforced-Carbon-Carbon material and were used to aid in the validation of an existing material model, MAT58. The computational analyses were performed using LS-DYNA, which is a physics-based, nonlinear, transient, finite element code used for analyzing material responses subjected to high impact forces and other dynamic conditions. The test results were used to validate LS-DYNA predictions and to determine the threshold of damage generated by the MAT58 cumulative damage material model. The threshold of damage parameter represents any external or internal visible RCC damage detectable by nondestructive evaluation techniques.

DEVELOPING A NO-VOC WOOD TOPCOAT

EPA Science Inventory

The paper reports an evaluation of a new low-VOC (volatile organic compound) wood coating technology, its performance characteristics, and its application and emissions testing. The low-VOC wood coating selected for the project was a two-component, water-based epoxy coating. Poly...

Wood products used for residential repair and remodeling in the United States, 1991

Treesearch

D. B. McKeever; R. G. Anderson

Large amounts of lumber and wood panel products are used annually for the repair and remodeling of residential structures and properties in the United States. In response to the need by government and industry for detailed information on this important market for timber products, a study was conducted by the Timber Demand and Technology...

MODELING OF ALKANE EMISSIONS FROM A WOOD STAIN

EPA Science Inventory

The article discusses full-scale residential house tests to evaluate the effects of organic emissions from a wood finishing product--wood stain--on indoor air quality (IAQ). The test house concentrations of three alkane species, nonane, decane, and undecane, were measured as a fu...

Impact of a rapid respiratory panel test on patient outcomes.

PubMed

Rogers, Beverly B; Shankar, Prabhu; Jerris, Robert C; Kotzbauer, David; Anderson, Evan J; Watson, J Renee; O'Brien, Lauren A; Uwindatwa, Francine; McNamara, Kelly; Bost, James E

2015-05-01

Evolution of polymerase chain reaction testing for infectious pathogens has occurred concurrent with a focus on value-based medicine. To determine if implementation of the FilmArray rapid respiratory panel (BioFire Diagnostics, Salt Lake City, Utah) (hereafter RRP), with a shorter time to the test result and expanded panel, results in different outcomes for children admitted to the hospital with an acute respiratory tract illness. Patient outcomes were compared before implementation of the RRP (November 1, 2011, to January 31, 2012) versus after implementation of the RRP (November 1, 2012, to January 31, 2013). The study included inpatients 3 months or older with an acute respiratory tract illness, most admitted through the emergency department. Testing before RRP implementation used batched polymerase chain reaction analysis for respiratory syncytial virus and influenza A and B, with additional testing for parainfluenza 1 through 3 in approximately 11% of patients and for human metapneumovirus in less than 1% of patients. The RRP tested for respiratory syncytial virus, influenza A and B, parainfluenza 1 through 4, human metapneumovirus, adenovirus, rhinovirus/enterovirus, and coronavirus NL62. The pre-RRP group had 365 patients, and the post-RRP group had 771 patients. After RRP implementation, the mean time to the test result was shorter (383 minutes versus 1119 minutes, P < .001), and the percentage of patients with a result in the emergency department was greater (51.6% versus 13.4%, P < .001). There was no difference in whether antibiotics were prescribed, but the duration of antibiotic use was shorter after RRP implementation (P = .003) and was dependent on receiving test results within 4 hours. If the test result was positive, the inpatient length of stay (P = .03) and the time in isolation (P = .03) were decreased after RRP implementation compared with before RRP implementation. The RRP decreases the duration of antibiotic use, the length of inpatient stay

Design of an Advanced Wood Composite Rotor and Development of Wood Composite Blade Technology

NASA Technical Reports Server (NTRS)

Stroebel, Thomas; Dechow, Curtis; Zuteck, Michael

1984-01-01

In support of a program to advance wood composite wind turbine blade technology, a design was completed for a prototype, 90-foot diameter, two-bladed, one-piece rotor, with all wood/epoxy composite structure. The rotor was sized for compatibility with a generator having a maximum power rating of 4000 kilowatts. Innovative features of the rotor include: a teetering hub to minimize the effects of gust loads, untwisted blades to promote rotor power control through stall, joining of blades to the hub structure via an adhesive bonded structural joint, and a blade structural design which was simplified relative to earlier efforts. The prototype rotor was designed to allow flexibility for configuring the rotor upwind or downwind of the tower, for evaluating various types of teeter dampers and/or elastomeric stops, and with variable delta-three angle settings of the teeter shaft axis. The prototype rotor was also designed with provisions for installing pressure tap and angle of attack instrumentation in one blade. A production version rotor cost analysis was conducted. Included in the program were efforts directed at developing advanced load take-off stud designs for subsequent evaluation testing by NASA, development of aerodynamic tip brake concepts, exploratory testing of a wood/epoxy/graphite concept, and compression testing of wood/epoxy laminate, with scarf-jointed plies.

A Better Way to Burn Wood.

ERIC Educational Resources Information Center

Robison, Rita

1979-01-01

Wood pyrolysis is a process that burns wood without air, producing gas and oil that are then burned for heat. Now being tested at Maryville College, Tennessee, the process is expected to cut fuel costs, solve a waste disposal problem, and produce charcoal for sale. (Author/MLF)

Effect of Thermal Treatment of Fast Growing Wood Fibers on Physical and Mechanical Properties of Light Medium Density Fiberboard

NASA Astrophysics Data System (ADS)

Jarusombuti, Songklod; Ayrilmis, Nadir; Fueangvivat, Vallayuth; Bauchongkol, Piyawade

2011-06-01

This study investigated physical and mechanical properties of the light medium density fiberboard (MDF) panels made from thermally treated wood fibers of eucalyptus camaldulensis at three different temperatures (393 K, 423 K or 453 K) for 30 or 60 min in a laboratory autoclave. The average thickness swelling of the panels decreased by 16-54% depending on the treatment temperature and time. However, the modulus of rupture, modulus of elasticity, and internal bond strength decreased by 16-37%, 9-25% and 10-39%, respectively. Based on the findings obtained from the present study, it may be said that wood fibers of E. camaldulensis treated at 453 K - 30 min can be used in the light MDF manufacture for use in humid conditions, such as kitchen and bathroom furniture requiring improved dimensional stability.

Electrical design for origami solar panels and a small spacecraft test mission

NASA Astrophysics Data System (ADS)

Drewelow, James; Straub, Jeremy

2017-05-01

Efficient power generation is crucial to the design of spacecraft. Mass, volume, and other limitations prevent the use of traditional spacecraft support structures from being suitable for the size of solar array required for some missions. Folding solar panel / panel array systems, however, present a number of design challenges. This paper considers the electrical design of an origami system. Specifically, it considers how to provide low impedance, durable channels for the generated power and the electrical aspects of the deployment system and procedure. The ability to dynamically reconfigure the electrical configuration of the solar cells is also discussed. Finally, a small satellite test mission to demonstrate the technology is proposed, before concluding.

Ultrasonic-Based Nondestructive Evaluation Methods for Wood: A Primer and Historical Review

Treesearch

Adam C. Senalik; Greg Schueneman; Robert J. Ross

2014-01-01

The authors conducted a review of ultrasonic testing and evaluation of wood and wood products, starting with a description of basic ultrasonic inspection setups and commonly used equations. The literature review primarily covered wood research presented between 1965 and 2013 in the Proceedings of the Nondestructive Testing of Wood Symposiums. A table that lists the...

Ecology of the Wood-boring Bivalve Martesia striata (Pholadidae) in Indian Waters

NASA Astrophysics Data System (ADS)

Yennawar, P. L.; Thakur, N. L.; Anil, A. C.; Venkat, K.; Wagh, A. B.

1999-08-01

Martesia striata (Linnaeus) is one of the dominant wood-boring organisms found in Indian waters. Incidence of this organism in the Zuari estuary (Goa) was evaluated by exposing wooden panels (Mangifera indica) to the marine environment between January 1996 and January 1997. Effects of salinity variation on embryonic and larval development were evaluated (salinity 0, 10, 20, 30, 35, 40 and 50, temperature 25 °C) and maximum metamorphic success was observed at 30 salinity. Results of the rearing experiments, destruction pattern of wood in the environment and reproductive biology indicate that although recruitment is halted during the monsoon, adults survive and become reproductively mature in the following post-monsoon, leading to increased recruitment during pre-monsoon months.

Wood flour

Treesearch

Craig M. Clemons; Daniel F. Caufield

2005-01-01

The term “wood flour” is somewhat ambiguous. Reineke states that the term wood flour “is applied somewhat loosely to wood reduced to finely divided particles approximating those of cereal flours in size, appearance, and texture”. Though its definition is imprecise, the term wood flour is in common use. Practically speaking, wood flour usually refers to wood particles...

Wood flour

Treesearch

Craig M. Clemons

2010-01-01

The term “wood flour” is somewhat ambiguous. Reineke states that the term wood flour “is applied somewhat loosely to wood reduced to finely divided particles approximating those of cereal flours in size, appearance, and texture.” Though its definition is imprecise, the term wood flour is in common use. Practically speaking, wood flour usually refers to wood particles...

Construction of Hydrophobic Wood Surface and Mechanical Property of Wood Cell Wall on Nanoscale Modified by Dimethyldichlorosilane

NASA Astrophysics Data System (ADS)

Yang, Rui; Wang, Siqun; Zhou, Dingguo; Zhang, Jie; Lan, Ping; Jia, Chong

2018-01-01

Dimethyldichlorosilane was used to improve the hydrophobicity of wood surface. The water contact angle of the treated wood surface increased from 85° to 143°, which indicated increased hydrophobicity. The nanomechanical properties of the wood cell wall were evaluated using a nanoindentation test to analyse the hydrophobic mechanism on the nano scale. The elastic modulus of the cell wall was significantly affected by the concentration but the influence of treatment time is insignificant. The hardness of the cell wall for treated samples was significantly affected by both treatment time and concentration. The interaction between treatment time and concentration was extremely significant for the elastic modulus of the wood cell wall.

Heat release rate of wood-plastic composites

Treesearch

N. M. Stark; R. H. White; C. M. Clemons

1997-01-01

Wood-plastic composites are becoming more important as a material that fulfills recycling needs. In this study, fire performance tests were conducted on several compositions of wood and plastic materials using the Ohio State University rate of heat release apparatus. Test results included five-minute average heat release rate in kW/m2 (HRR avg) and maximum heat release...

The Kiln Drying of Wood for Airplanes

NASA Technical Reports Server (NTRS)

Tiemann, Harry D

1919-01-01

This report is descriptive of various methods used in the kiln drying of woods for airplanes and gives the results of physical tests on different types of woods after being dried by the various kiln-drying methods.

Effect of citric acid modification of aspen wood on sorption of copper ion

Treesearch

James D. McSweeny; Roger M. Rowell; Soo Hong Min

2006-01-01

Milled aspen wood was thermochemically modified with citric acid for the purpose of improving the copper (Cu2+) ion sorption capacity of the wood when tested in 24-hour equilibrium batch tests. The wood-citric acid adducts provided additional carboxyl groups to those in the native wood and substantially increased Cu2+ ion uptake of the modified wood compared with that...

Full-Scale Test and Analysis Results of a PRSEUS Fuselage Panel to Assess Damage Containment Features

NASA Technical Reports Server (NTRS)

Bergan, Andrew; Bakuckas, John G., Jr.; Lovejoy, Andrew; Jegley, Dawn; Linton, Kim; Neal, Bert; Korkosz, Gregory; Awerbuch, Jonathan; Tan, Tein-Min

2012-01-01

Integrally stitched composite technology is an area that shows promise in enhancing the structural integrity of aircraft and aerospace structures. The most recent generation of this technology is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. The goal of the PRSEUS concept relevant to this test is to provide damage containment capability for composite structures while reducing overall structural weight. The National Aeronautics and Space Administration (NASA), the Federal Aviation Administration (FAA), and The Boeing Company have partnered in an effort to assess the damage containment features of a full-scale curved PRSEUS panel using the FAA Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility. A single PRSEUS test panel was subjected to axial tension, internal pressure, and combined axial tension and internal pressure loads. The test results showed excellent performance of the PRSEUS concept. No growth of Barely Visible Impact Damage (BVID) was observed after ultimate loads were applied. With a two-bay notch severing the central stringer, damage was contained within the two-bay region well above the required limit load conditions. Catastrophic failure was well above the ultimate load level. Information describing the test panel and procedure has been previously presented, so this paper focuses on the experimental procedure, test results, nondestructive inspection results, and preliminary test and analysis correlation.

Bio-based wood adhesives--preparation, characterization, and testing

USDA-ARS?s Scientific Manuscript database

Adhesive bonding plays an increasing role in the forest product industry and is a key factor for efficiently utilizing timber and other lignocellulosic resources. As synthetic wood adhesives are mostly derived from depleting petrochemical resources and have resulted in increasing environmental conce...

Static and fatigue testing of full-scale fuselage panels fabricated using a Therm-X(R) process

NASA Technical Reports Server (NTRS)

Dinicola, Albert J.; Kassapoglou, Christos; Chou, Jack C.

1992-01-01

Large, curved, integrally stiffened composite panels representative of an aircraft fuselage structure were fabricated using a Therm-X process, an alternative concept to conventional two-sided hard tooling and contour vacuum bagging. Panels subsequently were tested under pure shear loading in both static and fatigue regimes to assess the adequacy of the manufacturing process, the effectiveness of damage tolerant design features co-cured with the structure, and the accuracy of finite element and closed-form predictions of postbuckling capability and failure load. Test results indicated the process yielded panels of high quality and increased damage tolerance through suppression of common failure modes such as skin-stiffener separation and frame-stiffener corner failure. Finite element analyses generally produced good predictions of postbuckled shape, and a global-local modelling technique yielded failure load predictions that were within 7% of the experimental mean.

Surface Profiling and Core Evaluation of Aluminum Honeycomb Sandwich Aircraft Panels Using Multi-Frequency Eddy Current Testing

PubMed Central

Reyno, Tyler; Underhill, P. Ross; Krause, Thomas W.; Marsden, Catharine; Wowk, Diane

2017-01-01

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high-resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm2 area with dents ranging in depth from 0.13–1.01 mm was analyzed. The method was accurate at 1600 kHz to within 0.05 mm (2σ) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment. PMID:28906434

Surface Profiling and Core Evaluation of Aluminum Honeycomb Sandwich Aircraft Panels Using Multi-Frequency Eddy Current Testing.

PubMed

Reyno, Tyler; Underhill, P Ross; Krause, Thomas W; Marsden, Catharine; Wowk, Diane

2017-09-14

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high-resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1600 kHz to within 0.05 mm (2σ) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

The stress-strain relationships in wood and fiber-reinforced plastic laminae of reinforced glued-laminated wood beams

NASA Astrophysics Data System (ADS)

Tingley, Daniel Arthur

The reinforcement of wood and wood composite structural products to improve their mechanical properties has been in practice for many years. Recently, the use of high-strength fiber-reinforced plastic (FRP) as a reinforcement in such applications has been commercialized. The reinforcement is manufactured using a standard pultrusion process or alternatively a sheet-forming process commonly referred to as "pulforming". The high-modulus fibers are predominately unidirectional, although off-axis fibers are often used to enhance off-axis properties. The fibers used are either of a single type or multiple types, which are called "hybrids". Unidirectional, single, and hybrid fiber FRP physical properties and characteristics were compared to wood. Full-scale reinforced glulams were tested. Aramid-reinforced plastics (ARP) used as tensile reinforcements were found to be superior in strength applications to other types of FRP made with fiber, such as carbon and fiberglass. Carbon/aramid-reinforced plastic (CARP) was shown to be superior in both modulus and strength design situations. Fiberglass was shown to be suitable only in hybrid situations with another fiber such as aramid or carbon and only in limited use situations where modulus was a design criteria. The testing and analysis showed that the global response of reinforced glulam beams is controlled by localized strength variations in the wood such as slope of grain, knots, finger joints, etc. in the tensile zone. The elemental tensile strains in the extreme wood tensile laminae, due to global applied loads, were found to be well below the strain at failure in clear wood samples recovered from the failure area. Two areas affecting the relationship between the wood and the FRP were investigated: compatibility of the wood and FRP materials and interface characteristics between the wood and FRP. The optimum strain value at yield point for an FRP was assessed to be slightly higher than the clear wood value in tension for a

Stress-wave velocity of wood-based panels: effect of moisture, product type, and material direction

Treesearch

Guangping Han; Qinglin Wu; Xiping Wang

2006-01-01

The effect of moisture on longitudinal stress-wave velocity (SWV), bending stiffness. and bending strength of commercial oriented strandboard, plywood. particleboard. and southern pine lumber was evaluated. It was shown that the stress-wave verocity decreased in general with increases in panel moisture content (MC). At a given MC level. SWV varied with panel type and...

Low VOC drying of lumber and wood panel products. Progress report Number 9 [January 1999

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, H.; Banerjee, S.; Conners, T.

1999-01-01

Results from a multi-year study show that a significant part of the extensive variability observed in oriented strand board (OSB) flake dryer emissions can be traced to physiological effects, and the rest can be attributed to handling and other factors. Low-headspace treatment of lumber was scaled up to the 50 kg level. The amount of turpentine collected was of the same magnitude as that released upon drying lumber. For the process to be economical, the wood must first be brought to about 95 C with steam, and then processed with RF. Attempts to remove VOCs from OSB through low-headspace bymore » placing a curtain over the wood failed because of leaks. A more rigid container will be required. RF-treatment does not alter the gas permeability of lumber.« less

Thermal testing techniques for space shuttle thermal protection system panels

NASA Technical Reports Server (NTRS)

Cox, B. G.

1972-01-01

An experimental system was developed for evaluation of the effects of aerodynamic heating and cooling, vacuum, and pressure loading on candidate insulation packages proposed for use on the space shuttle. The system includes a number of design features which facilitate rapid recycle times. This is necessary to efficiently conduct extensive thermal cycling tests on these insulation packages to determine their reuse capabilities. The heart of the system is a 26-inch graphite element radiant heater. A susceptor plate functions as a uniform-temperature intermediate radiating surface. The susceptor also forms the lid of an inert atmosphere enclosure which separates the heater from the oxidizing test atmosphere. In some tests the plate properly simulates the heating from an actual flight heat-shield panel. Although other materials were used at lower required test temperatures, 2500 F was routinely achieved using a coated columbium susceptor plate.

6. COMPRESSOR CONTROL PANELS: AT LEFT, 6,000 P.S.I. PANEL, CIRCA ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. COMPRESSOR CONTROL PANELS: AT LEFT, 6,000 P.S.I. PANEL, CIRCA 1957; AT RIGHT, FACING CAMERA, 10,000 P.S.I. PANEL. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Helium Compression Plant, Test Area 1-115, intersection of Altair & Saturn Boulevards, Boron, Kern County, CA

Moisture content of wood for interior use...Douglas-fir and robusta eucalyptus samples studied

Treesearch

R. Sidney Boone

1967-01-01

Panels of Douglas-fir and robusta eucalyptus blocks showed little seasonal variation in Equilibrium Moisture Content (EMC) of wood at 19 indoor locations on Oahu, Hawaii. Differences in EMC between locations were more variable. Minimum EMC at nonair-conditioned locations was 10 percent;at air-conditioned locations. 8 percent. Maximum EMC at nonairconditioned locations...

Inhibition and stimulation effects in communities of wood decay fungi: exudates from colonized wood influence growth by other species.

PubMed

Heilmann-Clausen, J; Boddy, L

2005-04-01

The effects of exudates from uncolonized and from partly decayed beech wood on the extension rates of 16 later stage decay fungi were investigated. The partly decayed wood had been colonized by the pyrenomycete Eutypa spinosa, or the basidiomycetes Fomes fomentarius, Stereum hirsutum, and Trametes versicolor, all known as common early decay agents in European beech forests. Sterilized wood pieces were placed onto 0.5% malt agar, opposite to small agar plugs containing the test fungi. The latter showed very variable and species-specific growth responses to the various wood types. The presence of uncolonized wood stimulated extension rates in many species, whereas the four previously decayed wood types had variable stimulatory or inhibitory effects. Wood decayed by S. hirsutum resulted in reduced extension rate, delayed growth, or total inhibition in the majority of species, thus it is suggested that this species uses secondary metabolites in a defensive strategy. A single species was, however, stimulated in the presence of S. hirsutum-decayed wood. In contrast, the presence of wood decayed by F. fomentarius was stimulatory to 45% of the species. The other previously decayed wood types generally resulted in more variable responses, depending upon species. The results are discussed in an ecological context and it is suggested that the exudates from the partly decayed wood that are responsible for the reported effects may function as infochemicals, structuring microbial communities in wood.

Response of Microtermes mycophagus (Isoptera: Termitidae) to twenty one wood species

PubMed Central

Saeed, Shafqat

2015-01-01

The responses of termite species to bait depend upon the quality of the food used in the stations. Woods are the most common food sources for termites but different termite species behave differently to different wood species and types. The knowledge of the preference status of different wood species to a termite species helps in effective monitoring and baiting program. The current study was carried out to evaluate the preference of 21 wood species to the termite, Microtermes mycophagus in the field by no-choice and choice feeding tests. The results indicated silk cotton tree and sacred fig woods as the most preferred wood species with mean mass losses of 71.21 ± 5.09% and 68.38 ± 7.27% in no-choice test and 95.02 ± 1.65% and 91.69 ± 2.07% in choice tests, respectively. White cedar was the least preferred wood species with mean mass losses of 7.49 ± 1.64% and 13.92 ± 1.89% in no choice and choice feeding tests, respectively. Based on present studies, sapwood of silk cotton tree and sacred fig may be used in effective monitoring and baiting program against M. mycophagus. PMID:26312171

Thermal/Dynamic Characterization Test of the Solar Array Panel for Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Jenkins, Kathleen; Hershfeld, Donald J.

1999-01-01

The Hubble Space Telescope has experienced a problem maintaining pointing accuracy during emergence of the spacecraft from the Earth's shadow. The problem has been attributed to the rapid thermal gradient that develops when the heat from the Sun strikes the cold solar arrays. The thermal gradient causes the solar arrays to deflect or bend and this motion is sufficient to disturb the pointing control system. In order to alleviate this problem, a new design for the solar arrays has been fabricated. These new solar arrays will replace the current solar arrays during a future Hubble servicing mission. The new solar arrays have been designed so that the effective net motion of the center of mass of each panel is essentially zero. Although the solar array thermal deflection problem has been studied extensively over a period of years, a full scale test of the actual flight panels was required in order to establish confidence in the analyses. This test was conducted in the JPL Solar Simulation Facility in April, 1999. This presentation will discuss the objectives and methods of the test and present some typical test data.

F-15B in on ramp with close-up of test panels covered with advanced spray-on foam insulation materia

NASA Technical Reports Server (NTRS)

1999-01-01

Test panels covered with an advanced foam insulation material for the Space Shuttle's giant external fuel tank were test flown aboard an F-15B research aircraft at NASA's Dryden Flight Research Center, Edwards, Calif. Six panels were mounted on the left side of a heavily instrumented Flight Text Fixture mounted underneath the F-15B's fuselage. Insulation on this panel was finely machined over a horizontal rib structure to simulate in-line airflow past the tank; other panels had the ribs mounted vertically or had the insulation left in a rough as-sprayed surface. The tests were part of an effort by NASA's Marshall Space Flight Center to determine why small particles of the new insulation flaked off the tank on recent Shuttle missions. The tests with Dryden's F-15B were designed to replicate the pressure environment the Shuttle encounters during the first minute after launch. No noticeable erosion of the insulation material was noted after the flight experiment at Dryden.

Genetic Testing Integration Panels (GTIPs): A novel approach for considering integration of direct-to-consumer and other new genetic tests into patient care

PubMed Central

Uhlmann, Wendy R.; Sharp, Richard R.

2014-01-01

There has been a dramatic increase in the number of genetic tests available but few tests have practice guidelines. In addition, many tests have become available outside of genetics clinics through direct-to-consumer (DTC) companies and several offer tests not considered standard of care. To address several practical challenges associated with the rapid introduction of clinical and DTC genetic tests, we propose that genetic counselors and geneticists organize expert panels in their institutions to discuss the integration of new tests into patient care. We propose the establishment of Genetic Testing Integration Panels (GTIPs) to bring together local experts in medical genetics, genetic counseling, bioethics and law, health communication and clinical laboratory genetics. We describe key features of this approach and consider some of the potential advantages and limitations of using a GTIP to address the many clinical challenges raised by rapidly emerging clinical and DTC genetic tests. PMID:22246561

Exploring Valued-Added Options - Edge-Glued Panels and Blanks Offer Value-Added Opportunities

Treesearch

Bob Smith; Philip A. Araman

1997-01-01

As sawmills search for new opportunities to add value to rough sawn lumber, many consider producing dimension parts as one solution. Assembling dimension parts into edge-glued panels or standard blanks can add even further value. Blanks are defined as pieces of solid wood (which may be edge-glued) that are manufactured to a predetermined size. This article discusses...

A review of double-diffusion wood preservation suitable for Alaska.

Treesearch

K. Josephine Pavia

2006-01-01

Currently, all treated lumber used in Alaska is imported from the 48 contiguous states and Canada because there are no wood-treating facilities in Alaska. This report explores conventional and alternative wood-treating methods and reviews previous studies and laboratory tests on treated wood. In investigating wood treatment as a possible processing option for Alaska...

Dynamic tests of composite panels of an aircraft wing

NASA Astrophysics Data System (ADS)

Splichal, Jan; Pistek, Antonin; Hlinka, Jiri

2015-10-01

The paper describes the analysis of aerospace composite structures under dynamic loading. Today, it is common to use design procedures based on assumption of static loading only, and dynamic loading is rarely assumed and applied in design and certification of aerospace structures. The paper describes the application of dynamic loading for the design of aircraft structures, and the validation of the procedure on a selected structure. The goal is to verify the possibility of reducing the weight through improved design/modelling processes using dynamic loading instead of static loading. The research activity focuses on the modelling and testing of a composite panel representing a local segment of an aircraft wing section, investigating in particular the buckling behavior under dynamic loading. Finite Elements simulation tools are discussed, as well as the advantages of using a digital optical measurement system for the evaluation of the tests. The comparison of the finite element simulations with the results of the tests is presented.

What we miss if standard panel is used for skin prick testing?

PubMed

Cavkaytar, Ozlem; Buyuktiryaki, Betul; Sag, Erdal; Soyer, Ozge; Sekerel, Bulent E

2015-09-01

Although standard skin prick test (SPT) panels are crucial for routine investigation of sensitization in daily clinical practice, it has limitations in terms of missing allergens. To find out sensitization rates (SR)s to additional panel of allergens and their relative contributions in allergic diseases. SPTs with a battery of aeroallergens [tree pollen (A.glutinosa, C.arizonica, J.communis, T.platyphyllos, R.pseudoacacia), weed pollen (R.acetosa, U.dioica, A.artemisifolia), smut mix, yeast mix, storage mites (SM) (B.tropicalis, L.destructor, T.putrescentiae, A.siro), mouse and budgerigar epithelia], were performed to 318 participants (6-18 years) who were previously identified to be sensitized to at least one of the aeroallergens found in standard battery. Forty percent of participants were sensitized to at least one additional aerollergen. Three most frequent sensitizations were to B.tropicalis (11.3%), R.pseudoacacia (9.7%) and L.destructor (8.2%). SR for tree pollen increased from 6.9% to 19.8%, for mites increased from 26.3% to 31.6% and for moulds increased from 5.3% to 9.4% with addition of respective group of other allergens to battery. Furthermore, higher rates for additional tree pollen sensitization was found among patients with "only AR" (21%) compared to patients with "only asthma" (4.6%, p =0.006), contrarily higher rates for SM sensitization was found among patients with "only asthma" (20%) compared to patients with "only AR" (3.2%, p =0.003) CONCLUSIONS: Though some of sensitizations may occur due to cross-reactivity, almost 40% of sensitized children were also co-sensitized to the additional allergens tested. Physicians should consider further steps when a negative or inconsistent result is achieved through a standard skin test panel.

Chapter 6: Wood energy and competing wood product markers

Treesearch

Kenneth E. Skog; Robert C. Abt; Karen Abt

2014-01-01

Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

Wood adhesives : vital for producing most wood products

Treesearch

Charles R. Frihart

2011-01-01

A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

An illumination test is performed on the solar panel of a GOES-L satellite

NASA Technical Reports Server (NTRS)

1999-01-01

Workers (right) at Astrotech, Titusville, Fla., arrange the lights for an illumination test on the solar panel of the GOES-L weather satellite. The test is verifying the circuitry on the panel. The satellite is to be launched from Cape Canaveral Air Station aboard an Atlas II rocket in late March. The GOES-L is the fourth of a new advanced series of geostationary weather satellites for the National Oceanic and Atmospheric Administration. It is a three-axis inertially stabilized spacecraft that will provide pictures and perform atmospheric sounding at the same time. Once launched, the satellite, to be designated GOES-11, will undergo checkout and provide backup capabilities for the existing, aging GOES East weather satellite.

A new checkerboard panel for testing bacterial markers in periodontal disease.

PubMed

Dahlén, G; Leonhardt, A

2006-02-01

Various microbiological methods have been used for testing bacterial markers for periodontitis and periodontal disease progression. Most studies have used only a limited number of well recognized bacterial species. The purpose of the present study was to evaluate the association of 13 more recently identified bacterial species in a new panel in comparison with 12 previously more recognized periodontotopathogens ('old panel') using the 'checkerboard' DNA-DNA hybridization method. Fifty individuals were chosen who showed at least one site with a probing pocket depth of 6 mm or more (disease) and bleeding on probing and at least one site with a probing pocket depth of 3 mm and without bleeding on probing (health). One diseased and one healthy site on each individual were sampled with the paperpoint technique and the samples were processed in the checkerboard technique against deoxigenin-labeled whole genomic probes to 25 subgingival species representing 12 well recognized and 13 newly identified periodontitis associated species. Twenty-four (out of 25) species were detected more frequently in the subgingival plaque of diseased than healthy sites both at score 1 (> 10(4)) and score 3 (> 10(5)). A significant difference at the higher score (score 3) was noticed for all species of the old panel except for three (Streptococcus intermedius, Selenomonas noxia, and Eikenella corrodens). Of the species in the new panel only Prevotella tannerae, Filifactor alocis, and Porphyromonas endodontalis showed a statistical significant difference between diseased and healthy sites. It was concluded that P. tannerae, F. alocis, and P. endodontalis should be added to the 12 species used for routine diagnostics of periodontitis-associated bacterial flora.

The role of extractives in naturally durable wood species

Treesearch

G.T. Kirker; A.B. Blodgett; R.A. Arango; P.K. Lebow; C.A. Clausen

2013-01-01

There are numerous examples of wood species that naturally exhibit enhanced performance and longevity in outside exposure independent of preservative treatment. Wood extractives are largely considered to be the contributing factor when evaluating and predicting the performance of a naturally durable wood species. However, little test methodology exists that focuses on...

Lap Shear Testing of Candidate Radiator Panel Adhesives

NASA Technical Reports Server (NTRS)

Ellis, David; Briggs, Maxwell; McGowan, Randy

2013-01-01

During testing of a subscale radiator section used to develop manufacturing techniques for a full-scale radiator panel, the adhesive bonds between the titanium heat pipes and the aluminum face sheets failed during installation and operation. Analysis revealed that the thermal expansion mismatch between the two metals resulted in relatively large shear stresses being developed even when operating the radiator at moderate temperatures. Lap shear testing of the adhesive used in the original joints demonstrated that the two-part epoxy adhesive fell far short of the strength required. A literature review resulted in several candidate adhesives being selected for lap shear joint testing at room temperature and 398 K, the nominal radiator operating temperature. The results showed that two-part epoxies cured at room and elevated temperatures generally did not perform well. Epoxy film adhesives cured at elevated temperatures, on the other hand, did very well with most being sufficiently strong to cause yielding in the titanium sheet used for the joints. The use of an epoxy primer generally improved the strength of the joint. Based upon these results, a new adhesive was selected for the second subscale radiator section.

Are epoxy-wood bonds durable enough?

Treesearch

Charles R. Frihart

2005-01-01

An important aspect of any adhesive bond is that the bond maintains its integrity during its end use. Epoxies form highly durable bonds with many substrates but are usually not considered capable of forming completely durable bonds with wood by standard accelerated tests. However, epoxies are sold for wood boat construction, and some data have indicated that epoxies...

Buckling characteristics of hypersonic aircraft wing tubular panels

NASA Technical Reports Server (NTRS)

Ko, William L.; Shideler, John L.; Fields, Roger A.

1986-01-01

The buckling characteristics of Rene 41 tubular panels installed as wing panels on a hypersonic wing test structure (HWTS) were determined nondestructively through use of a force/stiffness technique. The nondestructive buckling tests were carried out under different combined load conditions and different temperature environments. Two panels were subsequently tested to buckling failure in a universal tension compression testing machine. In spite of some data scattering because of large extrapolations of data points resulting from termination of the test at a somewhat low applied load, the overall test data correlated fairly well with theoretically predicted buckling interaction curves. The structural efficiency of the tubular panels was slightly higher than that of the beaded panels which they replaced.

Wood and Sediment Dynamics in River Corridors

NASA Astrophysics Data System (ADS)

Wohl, E.; Scott, D.

2015-12-01

Large wood along rivers influences entrainment, transport, and storage of mineral sediment and particulate organic matter. We review how wood alters sediment dynamics and explore patterns among volumes of instream wood, sediment storage, and residual pools for dispersed pieces of wood, logjams, and beaver dams. We hypothesized that: volume of sediment per unit area of channel stored in association with wood is inversely proportional to drainage area; the form of sediment storage changes downstream; sediment storage correlates most strongly with wood load; and volume of sediment stored behind beaver dams correlates with pond area. Lack of data from larger drainage areas limits tests of these hypotheses, but analyses suggest a negative correlation between sediment volume and drainage area and a positive correlation between wood and sediment volume. The form of sediment storage in relation to wood changes downstream, with wedges of sediment upstream from jammed steps most prevalent in small, steep channels and more dispersed sediment storage in lower gradient channels. Use of a published relation between sediment volume, channel width, and gradient predicted about half of the variation in sediment stored upstream from jammed steps. Sediment volume correlates well with beaver pond area. Historically more abundant instream wood and beaver populations likely equated to greater sediment storage within river corridors. This review of the existing literature on wood and sediment dynamics highlights the lack of studies on larger rivers.

Concepts in the development of new accelerated test methods for wood decay

Treesearch

Darrel D. Nicholas; Douglas Crawford

2003-01-01

Efforts to develop new environmentally friendly wood preservatives are seriously handicapped by the extended time period required to carry out the evaluation needed to establish confidence in the long term performance of new preservative systems. Studies in our laboratory have shown that using strength loss as a measure of the extent of wood decay makes it possible to...

Thermal and structural tests of a hydrogen cooled panel

NASA Technical Reports Server (NTRS)

Richard, C. E.; Duncan, J. D.; Gellersen, E. W.; Demogenes, C.

1972-01-01

An experimental evaluation of the thermal and structural performance of a hydrogen-cooled panel is presented. The panel, which was of brazed Inconel 625 and Inconel 718 construction, was designed for a heat flux of 100 BTU per second-foot squared and an external surface pressure of 100 psi.

PANEL LIBRARY AND EDITOR

NASA Technical Reports Server (NTRS)

Raible, E.

1994-01-01

The Panel Library and Editor is a graphical user interface (GUI) builder for the Silicon Graphics IRIS workstation family. The toolkit creates "widgets" which can be manipulated by the user. Its appearance is similar to that of the X-Windows System. The Panel Library is written in C and is used by programmers writing user-friendly mouse-driven applications for the IRIS. GUIs built using the Panel Library consist of "actuators" and "panels." Actuators are buttons, dials, sliders, or other mouse-driven symbols. Panels are groups of actuators that occupy separate windows on the IRIS workstation. The application user can alter variables in the graphics program, or fire off functions with a click on a button. The evolution of data values can be tracked with meters and strip charts, and dialog boxes with text processing can be built. Panels can be stored as icons when not in use. The Panel Editor is a program used to interactively create and test panel library interfaces in a simple and efficient way. The Panel Editor itself uses a panel library interface, so all actions are mouse driven. Extensive context-sensitive on-line help is provided. Programmers can graphically create and test the user interface without writing a single line of code. Once an interface is judged satisfactory, the Panel Editor will dump it out as a file of C code that can be used in an application. The Panel Library (v9.8) and Editor (v1.1) are written in C-Language (63%) and Scheme, a dialect of LISP, (37%) for Silicon Graphics 4D series workstations running IRIX 3.2 or higher. Approximately 10Mb of disk space is required once compiled. 1.5Mb of main memory is required to execute the panel editor. This program is available on a .25 inch streaming magnetic tape cartridge in UNIX tar format for an IRIS, and includes a copy of XScheme, the public-domain Scheme interpreter used by the Panel Editor. The Panel Library Programmer's Manual is included on the distribution media. The Panel Library and

August 2007 FIFRA Scientific Advisory Panel Recommendations for SHEDS-Dietary and SHEDS-Residential Modules (Summarized) and EPA Responses

EPA Science Inventory

Over the past ten years, the Agency has requested the Panel to review several probabilistic dietary exposure software models. These have included DEEM-FCID™, Calendex-FCID, CARES™, LifeLine™, and an earlier (specialized) version of SHEDS (SHEDS-Wood) designed to assess exposure...

Investigation of panel-to-panel connections and block-outs for full-depth precast concrete bridge decks.

DOT National Transportation Integrated Search

2015-06-01

Experimental tests were performed at Virginia Tech to investigate transverse panel-to-panel connections and horizontal shear : connector block-outs for full-depth precast concrete bridge deck panels. The connections were designed for a deck replaceme...

Wood preservation

Treesearch

Stan T. Lebow

2010-01-01

Many commonly used wood species can deteriorate if exposed to conditions that support growth of wood-degrading organisms (see Chap. 14). Wood products can be protected from the attack of decay fungi, harmful insects, or marine borers by applying chemical preservatives. Preservative treatments greatly increase the life of wood structures, thus reducing replacement costs...

The decay of wood in landfills in contrasting climates in Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ximenes, Fabiano, E-mail: fabiano.ximenes@dpi.nsw.gov.au; Björdal, Charlotte; Cowie, Annette

Highlights: • We examine decay in wood from landfills in contrasting environments in Australia. • Analysis is based on changes in chemical composition and microscopy. • Climate did not influence levels of decay observed. • Microscopy of retrieved samples revealed most of the decay was aerobic in nature. • Current default factors for wood decay in landfills overestimate methane emissions. - Abstract: Wood products in landfill are commonly assumed to decay within several decades, returning the carbon contained therein to the atmosphere, with about half the carbon released as methane. However, the rate and extent of decay is not wellmore » known, as very few studies have examined the decay of wood products in landfills. This study reports on the findings from landfill excavations conducted in the Australian cities of Sydney and Cairns located in temperate and tropical environments, respectively. The objective of this study was to determine whether burial of the wood in warmer, more tropical conditions in Cairns would result in greater levels of decay than occurs in the temperate environment of Sydney. Wood samples recovered after 16–44 years in landfill were examined through physical, chemical and microscopic analyses, and compared with control samples to determine the carbon loss. There was typically little or no decay in the wood samples analysed from the landfill in Sydney. Although there was significant decay in rainforest wood species excavated from Cairns, decay levels for wood types that were common to both Cairns and Sydney landfills were similar. The current Intergovernmental Panel on Climate Change (IPCC, 2006) default decay factor for organic materials in landfills is 50%. In contrast, the carbon loss determined for Pinus radiata recovered from Sydney and Cairns landfills was 7.9% and 4.4%, respectively, and 0% for Agathis sp. This suggests that climate did not influence decay, and that the more extensive levels of decay observed for some wood

Toxicity of pyrolysis gases from wood

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Huttlinger, N. V.; Oneill, B. A.; Kourtides, D. A.; Parker, J. A.

1977-01-01

The toxicity of the pyrolysis gases from nine wood samples was investigated. The samples of hardwoods were aspen poplar, beech, yellow birch, and red oak. The samples of softwoods were western red cedar, Douglas fir, western hemlock, eastern white pine, and southern yellow pine. There was no significant difference between the wood samples under rising temperature conditions, which are intended to simulate a developing fire, or under fixed temperature conditions, which are intended to simulate a fully developed fire. This test method is used to determine whether a material is significantly more toxic than wood under the preflashover conditions of a developing fire.

Full-Scale Experimental Verification of Soft-Story-Only Retrofits of Wood-Frame Buildings using Hybrid Testing

Treesearch

Elaina Jennings; John W. van de Lindt; Ershad Ziaei; Pouria Bahmani; Sangki Park; Xiaoyun Shao; Weichiang Pang; Douglas Rammer; Gary Mochizuki; Mikhail Gershfeld

2015-01-01

The FEMA P-807 Guidelines were developed for retrofitting soft-story wood-frame buildings based on existing data, and the method had not been verified through full-scale experimental testing. This article presents two different retrofit designs based directly on the FEMA P-807 Guidelines that were examined at several different seismic intensity levels. The...

Dangerous (toxic) atmospheres in UK wood pellet and wood chip fuel storage.

PubMed

Simpson, Andrew T; Hemingway, Michael A; Seymour, Cliff

2016-09-01

There is growing use of wood pellet and wood chip boilers in the UK. Elsewhere fatalities have been reported, caused by carbon monoxide poisoning following entry into wood pellet storage areas. The aim of this work was to obtain information on how safely these two fuels are being stored in the UK. Site visits were made to six small-scale boiler systems and one large-scale pellet warehouse, to assess storage practice, risk management systems and controls, user knowledge, and potential for exposure to dangerous atmospheres. Real time measurements were made of gases in the store rooms and during laboratory tests on pellets and chips. Volatile organic compounds (VOCs) emitted and the microbiological content of the fuel was also determined. Knowledge of the hazards associated with these fuels, including confined space entry, was found to be limited at the smaller sites, but greater at the large pellet warehouse. There has been limited risk communication between companies supplying and maintaining boilers, those manufacturing and supplying fuel, and users. Risk is controlled by restricting access to the store rooms with locked entries; some store rooms have warning signs and carbon monoxide alarms. Nevertheless, some store rooms are accessed for inspection and maintenance. Laboratory tests showed that potentially dangerous atmospheres of carbon monoxide and carbon dioxide, with depleted levels of oxygen may be generated by these fuels, but this was not observed at the sites visited. Unplanned ventilation within store rooms was thought to be reducing the build-up of dangerous atmospheres. Microbiological contamination was confined to wood chips.

Dangerous (toxic) atmospheres in UK wood pellet and wood chip fuel storage

PubMed Central

Simpson, Andrew T.; Hemingway, Michael A.; Seymour, Cliff

2016-01-01

ABSTRACT There is growing use of wood pellet and wood chip boilers in the UK. Elsewhere fatalities have been reported, caused by carbon monoxide poisoning following entry into wood pellet storage areas. The aim of this work was to obtain information on how safely these two fuels are being stored in the UK. Site visits were made to six small-scale boiler systems and one large-scale pellet warehouse, to assess storage practice, risk management systems and controls, user knowledge, and potential for exposure to dangerous atmospheres. Real time measurements were made of gases in the store rooms and during laboratory tests on pellets and chips. Volatile organic compounds (VOCs) emitted and the microbiological content of the fuel was also determined. Knowledge of the hazards associated with these fuels, including confined space entry, was found to be limited at the smaller sites, but greater at the large pellet warehouse. There has been limited risk communication between companies supplying and maintaining boilers, those manufacturing and supplying fuel, and users. Risk is controlled by restricting access to the store rooms with locked entries; some store rooms have warning signs and carbon monoxide alarms. Nevertheless, some store rooms are accessed for inspection and maintenance. Laboratory tests showed that potentially dangerous atmospheres of carbon monoxide and carbon dioxide, with depleted levels of oxygen may be generated by these fuels, but this was not observed at the sites visited. Unplanned ventilation within store rooms was thought to be reducing the build-up of dangerous atmospheres. Microbiological contamination was confined to wood chips. PMID:27030057

Performance-oriented packaging testing of PPP-B-601 ERAPS wood box for packing Group II solid hazardous material. Test report for Oct 91

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, E.

1991-10-01

Qualification tests were performed to determine whether the in-service PPP-B-601 ERAPS Wood Box could be utilized to contain properly dunnaged solid type hazardous materials weighing up to a gross weight of 237 kg (523 pounds). The tests were conducted in accordance with Performance Oriented Packaging (POP) requirements specified by the United Nations Recommendations on the Transportation of Dangerous Goods. The box has conformed to the POP performance requirements; i.e., the box successfully retained its contents throughout the stacking, vibration and drop tests.

Pretreatment Characteristics of Waste Oak Wood by Ammonia Percolation

NASA Astrophysics Data System (ADS)

Kim, Jun-Seok; Kim, Hyunjoon; Lee, Jin-Suk; Lee, Joon-Pyo; Park, Soon-Chul

A log of waste oak wood collected from a Korean mushroom farm has been tested for ammonia percolation pretreatment. The waste log has different physical characteristics from that of virgin oak wood. The density of the waste wood was 30% lower than that of virgin oak wood. However, there is little difference in the chemical compositions between the woods. Due to the difference in physical characteristics, the optimal pretreatment conditions were also quite different. While for waste oak the optimum temperature was determined to be 130°C, for virgin oak wood the optimum pretreatment was only achieved at 170°C. Presoaking for 12 h with ammonia solution before pretreatment was helpful to increase the delignification efficiency.

Development and Evaluation of Stitched Sandwich Panels

NASA Technical Reports Server (NTRS)

Stanley, Larry E.; Adams, Daniel O.; Reeder, James R. (Technical Monitor)

2001-01-01

This study explored the feasibility and potential benefits provided by the addition of through-the-thickness reinforcement to sandwich structures. Through-the-thickness stitching is proposed to increase the interlaminar strength and damage tolerance of composite sandwich structures. A low-cost, out-of-autoclave processing method was developed to produce composite sandwich panels with carbon fiber face sheets, a closed-cell foam core, and through-the-thickness Kevlar stitching. The sandwich panels were stitched in a dry preform state, vacuum bagged, and infiltrated using Vacuum Assisted Resin Transfer Molding (VARTM) processing. For comparison purposes, unstitched sandwich panels were produced using the same materials and manufacturing methodology. Test panels were produced initially at the University of Utah and later at NASA Langley Research Center. Four types of mechanical tests were performed: flexural testing, flatwise tensile testing, core shear testing, and edgewise compression testing. Drop-weight impact testing followed by specimen sectioning was performed to characterize the damage resistance of stitched sandwich panels. Compression after impact (CAI) testing was performed to evaluate the damage tolerance of the sandwich panels. Results show significant increases in the flexural stiffness and strength, out-of-plane tensile strength, core shear strength, edgewise compression strength, and compression-after-impact strength of stitched sandwich structures.

Advances in the diagnosis of hereditary kidney cancer: Initial results of a multigene panel test.

PubMed

Nguyen, Kevin A; Syed, Jamil S; Espenschied, Carin R; LaDuca, Holly; Bhagat, Ansh M; Suarez-Sarmiento, Alfredo; O'Rourke, Timothy K; Brierley, Karina L; Hofstatter, Erin W; Shuch, Brian

2017-11-15

Panel testing has been recently introduced to evaluate hereditary cancer; however, limited information is available regarding its use in kidney cancer. The authors retrospectively reviewed test results and clinical data from patients who underwent targeted multigene panel testing of up to 19 genes associated with hereditary kidney cancer from 2013 to 2016. The frequency of positive (mutation/variant likely pathogenic), inconclusive (variant of unknown significance), and negative results was evaluated. A logistic regression analysis evaluated predictive factors for a positive test. Patients (n = 1235) had a median age at diagnosis of 46 years, which was significantly younger than the US population of individuals with kidney cancer (P < .0001). Overall, 6.1%, 75.5%, and 18.4% of individuals had positive, negative, and inconclusive results, respectively. The most commonly altered genes included folliculin (FLCN) and fumarate hydratase (FH), which were altered in 1.8% and 1.3% of patients, respectively. Tuberous Sclerosis Complex 2 (TSC2), mesenchymal epithelial transition factor proto-oncogene (MET), and PMS1 homolog 2 (PMS2) had the highest rates of variants of unknown significance, which were identified in 2.7%, 2.2%, and 1.7% of patients, respectively. Early age of onset was the only factor that was identified as predictive of a positive test on multivariate analysis (odds ratio, 0.975; P = .0052) and may be the only identifying characteristic of low-penetrant syndromes, such as those associated with MITF (melanogenesis-associated transcription factor) mutations, which do not have singular histology or a family history of kidney cancer. Panel tests may be particularly useful for patients who lack distinguishing clinical characteristics of known hereditary kidney cancer syndromes. The current results support the use of early age of onset for genetic counseling and/or testing. Cancer 2017;123:4363-71. © 2017 American Cancer Society. © 2017 American

Skin prick testing to aeroallergen extracts: what is the optimal panel in children and adolescents in Turkey?

PubMed

Şahiner, Umit Murat; Civelek, Ersoy; Yavuz, Süleyman Tolga; Büyüktiryaki, Ayşe Betül; Tuncer, Ayfer; Şekerel, Bülent Enis

2012-01-01

The skin prick test (SPT) is the standard tool for the diagnosis of IgE-mediated allergic diseases. The number and spectrum of allergen extracts to be applied for the diagnosis of sensitized patients in order to achieve the most cost-effective and informative results are critical from both economic and scientific viewpoints. In order to determine the minimum test battery panel necessary to cover at least 95% of the cases of SPT sensitization in children and adolescents (2-18 years) with suspected respiratory allergies, we retrospectively analyzed the SPT results of the largest referral center of the country. Over a 2.5-year period, a total of 2,457 children (male/female ratio 1.51) with a median (range) age of 6.8 years (2.0-18.0) were subjected to SPT. Eight hundred and sixty-two (35.1%) children were found to be sensitized to at least one of the 30 aeroallergen extracts tested. The most common sensitizations were to grasses (Festuca pratensis, Phleum pratense, Dactylis glomerata, and Lolium perenne), house dust mites (Dermatophagoides pteronyssinus and Dermatophagoides farinae), cat, weeds (Chenopodium, Plantago, and Artemisia), and moulds (Alternaria and Cladosporium). The sensitization rates increased in conjunction with an increase in age. Testing with 12, 8, and 7 allergens was sufficient to identify over 95% of the sensitized preschool children, school children, and adolescents, respectively. An SPT panel covering 12 allergen extracts was sufficient to detect most of the sensitized children and adolescents with recurrent respiratory symptoms. As the patients grow older, a smaller test panel is required compared to the panels used at younger ages. Copyright © 2011 S. Karger AG, Basel.

Development of a tornado safe room door from wood Products: door design and impact testing

Treesearch

Robert H. Falk; James J. Bridwell

2016-01-01

In this study, a tornado safe room door built from wood products and steel sheeting was developed and impact-tested according to tornado safe room standards. Results indicate that an door constructed from as few as two sheets of 23/32-in. (18.26-mm) construction-grade plywood and overlaid with 18-gauge (0.05-in.- (1.27- mm-) thick) steel can pass the required impact...

Economics of Concrete and Wood Tie Track Structures

DOT National Transportation Integrated Search

1978-08-01

This report presents results from an evaluation of the economic benefits of concrete- versus wood-tie track. The analysis includes the life-cycle capital, maintenance, and renewal costs for concrete- and wood-tie track for four specific test cases an...

Coatings to reduce wood preservative leaching.

PubMed

Nejad, Mojgan; Cooper, Paul

2010-08-15

The efficiency of semitransparent penetrating stains to reduce leaching of wood preservative components was evaluated. Five commercial wood deck finishes were applied to untreated and chromated copper arsenate (CCA), alkaline copper quat (ACQ), and copper azole (CA) treated wood, and leachates were collected and analyzed during 3 years of natural weathering exposure in Toronto, Canada. All stains evaluated effectively reduced the cumulative leaching of all inorganic preservative components by about 60% on average. Although most coatings showed significant film degradation starting around 12 months, the reduced leaching persisted even after 3 years. This suggests that temporary protection of wood with a coating during the early stages of use resulted in long-term reduction in preservative leaching potential. A two-week screening leaching test was able to predict the long-term leaching performance of different coatings reasonably well. Cured coating glass transition temperature (Tg) and liquid coating viscosity were the most important variables affecting a leaching prediction model. To effectively reduce leaching of preservative components from treated wood, coatings should have Tg low enough to withstand stresses caused by freezing in winter and have adequate viscosity to form a barrier film layer on the wood surface.

Velcro mechanics in wood

Treesearch

David Kretschmann

2003-12-01

The remarkable deformability of wood in a moist environment resembles that of ductile metals. A combination of traditional mechanical tests and cutting-edge diffraction experiments reveal the molecular mechanism that determines such behaviour.

Wide Panel Testing Technique for Evaluating Repair Weld Strengths

NASA Technical Reports Server (NTRS)

Rogers, Patrick R.; Bynum, Julian E.; Shah, Sandeep R.

1998-01-01

This paper describes a new tensile testing technique for evaluating the overall effect of a repair weld on the strength of a welded joint. Previously, repair weld strengths have been evaluated using one-inch width tensile specimens, but this technique does not capture all of the effects that result from a repair. The new technique involves testing of "wide panel" tensile specimens which contain the full length of a repair weld within a longer initial weld, allowing the specimen to capture the combined effects of residual stresses, local strength degradation, and load redistribution around a repair. The development of strains in the repair area of standard aluminum alloy specimens and new high-performance aluminum-lithium alloy specimens was observed and evaluated using photoelastic material. The results of this evaluation show an increased sensitivity to repair welding residual stresses in the aluminum-lithium alloy specimens.

Competitive outcomes between wood-decaying fungi are altered in burnt wood.

PubMed

Edman, Mattias; Eriksson, Anna-Maria

2016-06-01

Fire is an important disturbance agent in boreal forests where it creates a wide variety of charred and other types of heat-modified dead wood substrates, yet how these substrates affect fungal community structure and development within wood is poorly understood. We allowed six species of wood-decaying basidiomycetes to compete in pairs in wood-discs that were experimentally burnt before fungal inoculation. The outcomes of interactions in burnt wood differed from those in unburnt control wood for two species:Antrodia sinuosanever lost on burnt wood and won over its competitor in 67% of the trials compared to 40% losses and 20% wins on unburnt wood. In contrast, Ischnoderma benzoinumwon all interactions on unburnt wood compared to 33% on burnt wood. However, the responses differed depending on the identity of the competing species, suggesting an interaction between competitor and substrate type. The observed shift in competitive balance between fungal species probably results from chemical changes in burnt wood, but the underlying mechanism needs further investigation. Nevertheless, the results indicate that forest fires indirectly structure fungal communities by modifying dead wood, and highlight the importance of fire-affected dead wood substrates in boreal forests. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

The fractal characteristic of facial anthropometric data for developing PCA fit test panels for youth born in central China.

PubMed

Yang, Lei; Wei, Ran; Shen, Henggen

2017-01-01

New principal component analysis (PCA) respirator fit test panels had been developed for current American and Chinese civilian workers based on anthropometric surveys. The PCA panels used the first two principal components (PCs) obtained from a set of 10 facial dimensions. Although the PCA panels for American and Chinese subjects adopted the bivairate framework with two PCs, the number of the PCs retained in the PCA analysis was different between Chinese subjects and Americans. For the Chinese youth group, the third PC should be retained in the PCA analysis for developing new fit test panels. In this article, an additional number label (ANL) is used to explain the third PC in PCA analysis when the first two PCs are used to construct the PCA half-facepiece respirator fit test panel for Chinese group. The three-dimensional box-counting method is proposed to estimate the ANLs by calculating fractal dimensions of the facial anthropometric data of the Chinese youth. The linear regression coefficients of scale-free range R 2 are all over 0.960, which demonstrates that the facial anthropometric data of the Chinese youth has fractal characteristic. The youth subjects born in Henan province has an ANL of 2.002, which is lower than the composite facial anthropometric data of Chinese subjects born in many provinces. Hence, Henan youth subjects have the self-similar facial anthropometric characteristic and should use the particular ANL (2.002) as the important tool along with using the PCA panel. The ANL method proposed in this article not only provides a new methodology in quantifying the characteristics of facial anthropometric dimensions for any ethnic/racial group, but also extends the scope of PCA panel studies to higher dimensions.

Periodate and hypobromite modification of Southern pine wood to improve sorption of copper ion

Treesearch

James D. McSweeny; Roger M. Rowell; George C. Chen; Thomas L. Eberhardt; Min Soo-Hong

2008-01-01

Milled southern pine wood was modified with sequential treatments of sodium periodate and sodium hypobromite for the purpose of improving copper ion (Cu2+) sorption capacity of the wood when tested in 24-h equilibrium batch tests. The modified wood provided additional carboxyl groups to those in the native wood and substantially increased Cu2+ uptake over that of...

Extension of the ACE solar panels is tested in SAEF-II

NASA Technical Reports Server (NTRS)

1997-01-01

Extension of the solar panels is tested on the Advanced Composition Explorer (ACE) spacecraft in KSC's Spacecraft Assembly and Encapsulation Facility-II (SAEF-II). Scheduled for launch on a Delta II rocket from Cape Canaveral Air Station on Aug. 25, ACE will study low-energy particles of solar origin and high-energy galactic particles. The collecting power of instruments aboard ACE is 10 to 1,000 times greater than anything previously flown to collect similar data by NASA.

The Effect of Kiln Drying on the Strength of Airplane Woods

NASA Technical Reports Server (NTRS)

Wilson, T R C

1920-01-01

This report is a very complete treatise on the comparative strength of air and kiln dried wood. The series of tests includes 26 species of wood, approximately 100 kiln runs, and over 10,000 mechanical tests.

Propulsion and Energetics Panel Working Group 15 on the Uniform Engine Test Programme

DTIC Science & Technology

1990-02-01

earlier test of uniform aerodynamic models in wind tunnels under the auspices of the Fluid Dynamics Panel. A formal proposal was presented to the...this major new effort and members of the engine test community throughout AGARD were selected to serve on Working Group 15 along with PEP...STPA/MO 4 Mr J.R.Bednarsk; 4 Avenue de Ia Porte d’lssy PE-63 75015 Paris Naval Air Propulsion Center PO Box 7176 GERMANY Trenton. New Jersey 08628

Residual Strength Pressure Tests and Nonlinear Analyses of Stringer- and Frame-Stiffened Aluminum Fuselage Panels with Longitudinal Cracks

NASA Technical Reports Server (NTRS)

Young, Richard D.; Rouse, Marshall; Ambur, Damodar R.; Starnes, James H., Jr.

1999-01-01

The results of residual strength pressure tests and nonlinear analyses of stringer- and frame-stiffened aluminum fuselage panels with longitudinal cracks are presented. Two types of damage are considered: a longitudinal crack located midway between stringers, and a longitudinal crack adjacent to a stringer and along a row of fasteners in a lap joint that has multiple-site damage (MSD). In both cases, the longitudinal crack is centered on a severed frame. The panels are subjected to internal pressure plus axial tension loads. The axial tension loads are equivalent to a bulkhead pressure load. Nonlinear elastic-plastic residual strength analyses of the fuselage panels are conducted using a finite element program and the crack-tip-opening-angle (CTOA) fracture criterion. Predicted crack growth and residual strength results from nonlinear analyses of the stiffened fuselage panels are compared with experimental measurements and observations. Both the test and analysis results indicate that the presence of MSD affects crack growth stability and reduces the residual strength of stiffened fuselage shells with long cracks.

Residual Strength Pressure Tests and Nonlinear Analyses of Stringer-and Frame-Stiffened Aluminum Fuselage Panels with Longitudinal Cracks

NASA Technical Reports Server (NTRS)

Young, Richard D.; Rouse, Marshall; Ambur, Damodar R.; Starnes, James H., Jr.

1998-01-01

The results of residual strength pressure tests and nonlinear analyses of stringer- and frame-stiffened aluminum fuselage panels with longitudinal cracks are presented. Two types of damage are considered: a longitudinal crack located midway between stringers, and a longitudinal crack adjacent to a stringer and along a row of fasteners in a lap joint that has multiple-site damage (MSD). In both cases, the longitudinal crack is centered on a severed frame. The panels are subjected to internal pressure plus axial tension loads. The axial tension loads are equivalent to a bulkhead pressure load. Nonlinear elastic-plastic residual strength analyses of the fuselage panels are conducted using a finite element program and the crack-tip-opening-angle (CTOA) fracture criterion. Predicted crack growth and residual strength results from nonlinear analyses of the stiffened fuselage panels are compared with experimental measurements and observations. Both the test and analysis results indicate that the presence of MSD affects crack growth stability and reduces the residual strength of stiffened fuselage shells with long cracks.

Assemblage composition of fungal wood-decay species has a major influence on how climate and wood quality modify decomposition.

PubMed

Venugopal, Parvathy; Junninen, Kaisa; Edman, Mattias; Kouki, Jari

2017-03-01

The interactions among saprotrophic fungal species, as well as their interactions with environmental factors, may have a major influence on wood decay and carbon release in ecosystems. We studied the effect that decomposer diversity (species richness and assemblage composition) has on wood decomposition when the climatic variables and substrate quality vary simultaneously. We used two temperatures (16 and 21°C) and two humidity levels (70% and 90%) with two wood qualities (wood from managed and old-growth forests) of Pinus sylvestris. In a 9-month experiment, the effects of fungal diversity were tested using four wood-decaying fungi (Antrodia xantha, Dichomitus squalens, Fomitopsis pinicola and Gloeophyllum protractum) at assemblage levels of one, two and four species. Wood quality and assemblage composition affected the influence of climatic factors on decomposition rates. Fungal assemblage composition was found to be more important than fungal species richness, indicating that species-specific fungal traits are of paramount importance in driving decomposition. We conclude that models containing fungal wood-decay species (and wood-based carbon) need to take into account species-specific and assemblage composition-specific properties to improve predictive capacity in regard to decomposition-related carbon dynamics. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Development of naphthenic acid fractionation with supercritical fluid extraction for use in wood decay testing

Treesearch

Brett Niemi; Wayne St. John; Bessie Woodward; Rodney DeGroot; Gary McGinnis

2000-01-01

In recent years, the performance of copper naphthenate as a wood preservative has been in question. To understand the varying results of copper naphthenate in preventing wood decay, a closer look at eight naphthenic acid (NA) supplies was undertaken. Initial studies of NA samples from individual suppliers revealed large differences in chemical composition and wood...

Vibration characteristics of teak wood filled steel tubes

NASA Astrophysics Data System (ADS)

Danawade, Bharatesh Adappa; Malagi, Ravindra Rachappa

2018-05-01

The objective of this paper is to determine fundamental frequency and damping ratio of teak wood filled steel tubes. Mechanically bonded teak wood filled steel tubes have been evaluated by experimental impact hammer test using modal analysis. The results of impact hammer test were verified and validated by finite element tool ANSYS using harmonic analysis. The error between the two methods was observed to be within acceptable limit.

Tropical wood resistance to the West Indian drywood termite Cryptotermes brevis: If termites can't chew….

PubMed

Cosme, Lírio; Haro, Marcelo M; Guedes, Nelsa Maria P; Della Lucia, Terezinha Maria C; Guedes, Raul Narciso C

2018-04-01

The importance and impact of invasive species are usually considered based on their economic implications, particularly the direct damage that they cause. The West Indian drywood termite Cryptotermes brevis (Walker) is an example and is a concern in structural lumber, furniture, and other wood products. Despite its importance, its tropical wood preferences and the wood physical characteristics contributing to resistance have not been investigated to date. Here, we developed wood testing units to allow the X-ray recording of termite colonization and then subsequently tested tropical wood resistance to the termite through free-choice and no-choice bioassays using these wood testing units. The relevance of wood density and hardness as determinants of such resistance was also tested, as was termite mandible wear. The wood testing units used allowed the assessment of the termite infestation and wood area loss, enabling subsequent choice bioassays to be performed. While pine (Pinus sp.), jequitiba (Cariniana sp.) and angelim (Hymenolobium petraenum) exhibited the heaviest losses and highest infestations; cumaru (Dipteryx odorata), guariuba (Clarisia racemosa), and purpleheart (Peltogyne sp.) showed the lowest losses and infestations; courbaril (Hymenaea courbaril), eucalyptus (Eucalyptus sp.), and tatajuba (Bagassa guianensis) exhibited intermediary results. Wood hardness and in particular wood density were key determinants of wood resistance to the termites, which exhibited lower infestations associated with greater mandible wear when infesting harder high-density wood. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Cryogenic performance of slotted brazed Rene 41 honeycomb panels

NASA Technical Reports Server (NTRS)

Hepler, A. K.; Swegle, A. R.

1982-01-01

Two brazed Rene 41 honeycomb panels that would incorporate a frame element were designed, fabricated and tested. The panels were representative of the lower surface of an advanced space transportation vehicle. The first panel was a two span panel supported by a center frame and on edges parallel to it. The second panel was a two span panel supported by a center frame and on edges parallel to it. The second panel was a three span panel supported on two frames and on edges parallel to the frames. Each panel had its outer skin slotted to reduce the thermal stresses of the panel skins. The first panel was tested under simulated boost conditions that included liquid hydrogen exposure of the frame and inner skin and radiant heat to 478K on the outer skins. The first panel was tested to investigate the effect of thermal stresses in skins and core caused by the panel being restrained by a cold integral frame and to observe the effects of frost formation and possible liquid air development in and around outer skin slots.

Exposure testing of fasteners in preservative treated wood : gravimetric corrosion rates and corrosion product analyses

Treesearch

Samuel L. Zelinka; Rebecca J. Sichel; Donald S. Stone

2010-01-01

Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27oC at 100% relative humidity for 1 year. The...

On Laminar to Turbulent Transition of Arc-Jet Flow in the NASA Ames Panel Test Facility

NASA Technical Reports Server (NTRS)

Gokcen, Tahir; Alunni, Antonella I.

2012-01-01

This paper provides experimental evidence and supporting computational analysis to characterize the laminar to turbulent flow transition in a high enthalpy arc-jet facility at NASA Ames Research Center. The arc-jet test data obtained in the 20 MW Panel Test Facility include measurements of surface pressure and heat flux on a water-cooled calibration plate, and measurements of surface temperature on a reaction-cured glass coated tile plate. Computational fluid dynamics simulations are performed to characterize the arc-jet test environment and estimate its parameters consistent with the facility and calibration measurements. The present analysis comprises simulations of the nonequilibrium flowfield in the facility nozzle, test box, and flowfield over test articles. Both laminar and turbulent simulations are performed, and the computed results are compared with the experimental measurements, including Stanton number dependence on Reynolds number. Comparisons of computed and measured surface heat fluxes (and temperatures), along with the accompanying analysis, confirm that that the boundary layer in the Panel Test Facility flow is transitional at certain archeater conditions.

Wood fuel preparation

Treesearch

L. H. Reineke

1965-01-01

This report gives information on the preparation of wood fuel from wood residues and other wood raw materials. Types of wood fuel discussed are cordwood, stovewood, slabwood, kindling, chips, hogged fuel, sawdust and shavings, bark, charcoal, alcohol, and briquets. Related information is given on types of machinery for preparing wood fuel and on possible markets for...

Effect of wood flour content on the optical color, surface chemistry, mechanical and morphological properties of wood flour/recycled high density polyethylene (rHDPE) composite

NASA Astrophysics Data System (ADS)

Sheng, Chan Kok; Amin, Khairul Anuar Mat; Kee, Kwa Bee; Hassan, Mohd Faiz; Ali, E. Ghapur E.

2018-05-01

In this study, effect of wood flour content on the color, surface chemistry, mechanical properties and surface morphology of wood-plastic composite (WPC) on different mixture ratios of recycled high density polyethylene (rHDPE) and wood flour were investigated in detail. The presence of wood flour in the composite indicates a significant total color change and a decrease of lightness. Functional groups of wood flour in WPC can be seen clearer from the Fourier transform infrared (FTIR) spectra as the wood flour content increases. The mechanical tensile testing shows that the tensile strength of Young's modulus is improved, whereas the strain and elongation at break were reduced by the addition of wood flour. The gap between the wood flour microvoid fibre and rHDPE matrix becomes closer when the wood flour content is increased as observed by scanning electron microscope (SEM) image. This finding implies a significant improvement on the interaction of interfacial adhesion between the rHDPE matrix and wood flour filler in the present WPC.

Structural fire design : wood

Treesearch

E. L. Schaffer

Analytical procedures to predict the fire endurance of structural wood members have been developed worldwide. This research is reviewed for capability to predict the results of tests in North America and what considerations are necessary to apply the information here. Critical research needs suggested include: (1) Investigation of load levels used in reported tests,...

Potential for Biobased Adhesives in Wood Bonding

Treesearch

Charles R. Frihart

2016-01-01

There has been a resurgence of interest and research on using bio-based materials as wood adhesives; however, they have achieved only limited market acceptance. To better understand this low level of replacement, it is important to understand why adhesives work or fail in moisture durability tests. A holistic model for wood adhesives has been developed that clarifies...

Aircraft woods: their properties, selection, and characteristics

NASA Technical Reports Server (NTRS)

Markwardt, L J

1931-01-01

Strength values of various woods for aircraft design for a 15 per cent moisture condition of material and a 3-second duration of stress are presented, and also a discussion of the various factors affecting the values. The toughness-test method of selecting wood is discussed, and a table of acceptance values for several species is given.

Synthesis of published and unpublished corrosion data from long term tests of fasteners embedded in wood : calculation of corrosion rates and the effect of corrosion on lateral joint strength

Treesearch

Samuel L. Zelinka; Douglas R. Rammer

2011-01-01

In the past 5 years, several accelerated test methods have been developed to measure the corrosion of metals in contact with wood. It is desirable to contrast these accelerated results against those of long term exposure tests. While there have been several published long-term exposure tests performed on metals in treated wood, the data from these studies could not be...

Variation in wood nutrients along a tropical soil fertility gradient.

PubMed

Heineman, Katherine D; Turner, Benjamin L; Dalling, James W

2016-07-01

Wood contains the majority of the nutrients in tropical trees, yet controls over wood nutrient concentrations and their function are poorly understood. We measured wood nutrient concentrations in 106 tree species in 10 forest plots spanning a regional fertility gradient in Panama. For a subset of species, we quantified foliar nutrients and wood density to test whether wood nutrients scale with foliar nutrients at the species level, or wood nutrient storage increases with wood density as predicted by the wood economics spectrum. Wood nutrient concentrations varied enormously among species from fourfold in nitrogen (N) to > 30-fold in calcium (Ca), potassium (K), magnesium (Mg) and phosphorus (P). Community-weighted mean wood nutrient concentrations correlated positively with soil Ca, K, Mg and P concentrations. Wood nutrients scaled positively with leaf nutrients, supporting the hypothesis that nutrient allocation is conserved across plant organs. Wood P was most sensitive to variation in soil nutrient availability, and significant radial declines in wood P indicated that tropical trees retranslocate P as sapwood transitions to heartwood. Wood P decreased with increasing wood density, suggesting that low wood P and dense wood are traits associated with tree species persistence on low fertility soils. Substantial variation among species and communities in wood nutrient concentrations suggests that allocation of nutrients to wood, especially P, influences species distributions and nutrient dynamics in tropical forests. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

The use of wood for wind turbine blade construction

NASA Technical Reports Server (NTRS)

Gougeon, M.; Zuteck, M.

1979-01-01

The interrelationships between moisture and wood, conditions for dry rot spore activity, the protection of wood fibers from moisture, wood resin composites, wood laminating, quality control, and the mechanical properties of wood are discussed. The laminated veneer and the bonded sawn stock fabrication techniques, used in the construction of a turbine blade with a monocoque 'D' section forming the leading edge and a built up trailing edge section, are described. A 20 foot root end sample complete with 24 bonded-in studs was successfully subjected to large onetime loads in both the flatwise and edgewise directions, and to fatigue tests. Results indicate that wood is both a viable and advantageous material for use in wind turbine blades. The basic material is reasonably priced, domestically available, ecologically sound, and easily fabricated with low energy consumption.

Pathogenic and likely pathogenic variant prevalence among the first 10,000 patients referred for next-generation cancer panel testing

PubMed Central

Susswein, Lisa R.; Marshall, Megan L.; Nusbaum, Rachel; Vogel Postula, Kristen J.; Weissman, Scott M.; Yackowski, Lauren; Vaccari, Erica M.; Bissonnette, Jeffrey; Booker, Jessica K.; Cremona, M. Laura; Gibellini, Federica; Murphy, Patricia D.; Pineda-Alvarez, Daniel E.; Pollevick, Guido D.; Xu, Zhixiong; Richard, Gabi; Bale, Sherri; Klein, Rachel T.; Hruska, Kathleen S.; Chung, Wendy K.

2016-01-01

Purpose: Germ-line testing for panels of cancer genes using next-generation sequencing is becoming more common in clinical care. We report our experience as a clinical laboratory testing both well-established, high-risk cancer genes (e.g., BRCA1/2, MLH1, MSH2) as well as more recently identified cancer genes (e.g., PALB2, BRIP1), many of which have increased but less well-defined penetrance. Genet Med 18 8, 823–832. Methods: Clinical genetic testing was performed on over 10,000 consecutive cases referred for evaluation of germ-line cancer genes, and results were analyzed for frequency of pathogenic or likely pathogenic variants, and were stratified by testing panel, gene, and clinical history. Genet Med 18 8, 823–832. Results: Overall, a molecular diagnosis was made in 9.0% of patients tested, with the highest yield in the Lynch syndrome/colorectal cancer panel. In patients with breast, ovarian, or colon/stomach cancer, positive yields were 9.7, 13.4, and 14.8%, respectively. Approximately half of the pathogenic variants identified in patients with breast or ovarian cancer were in genes other than BRCA1/2. Genet Med 18 8, 823–832. Conclusion: The high frequency of positive results in a wide range of cancer genes, including those of high penetrance and with clinical care guidelines, underscores both the genetic heterogeneity of hereditary cancer and the usefulness of multigene panels over genetic tests of one or two genes. Genet Med 18 8, 823–832. PMID:26681312

Wood-based Tri-Axial Sandwich Composite Materials: Design, Fabrication, Testing, Modeling and Application

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2014-01-01

As the demand for sustainable materials increases, there are unique challenges and opportunities to develop light-weight green composites materials for a wide range of applications. Thus wood-based composite materials from renewable forests may provide options for some niche applications while helping to protect our environment. In this paper, the wood-based tri-axial...

Wood Preference of Reticulitermes virginicus (Blattodea: Rhinotermitidae) Using No-, Two-, and Four-Choice Designs and Seven Different Measures of Wood Consumption.

PubMed

Lee, T-Y; Forschler, B T

2016-04-01

Three hundred Reticulitermes virginicus (Banks) workers were exposed to three 1-cm3 wood blocks of either Quercus sp. (Red Oak), Populus sp. (Poplar), Pinus sp. (Pine), or Sequoia sp. (Redwood) placed into one of the three bioassay designs (no-, two-, and four-choice) for 21 d. Termite wood consumption was measured by wood weight loss, resistance class, and visual rating. Wood consumption rates were determined using four formulas in addition to two standardized visual rating scales (American Society for Testing and Materials [ASTM] and American Wood Protection Association [AWPA]) and a preference ranking obtained for each measure. The wood consumption formula, rating scale, and preference rankings were compared by bioassay design. The overall preference ranking of the four wood types as determined by the combination of all three designs was—1) Pine, 2) Red Oak, 3) Redwood, and 4) Poplar. Results indicate that bioassay design influenced both wood consumption and preference rankings. A no-choice design can determine aversion; a four-choice design the most preferred wood; and a two-choice design can illuminate the fine details of comparative preference. The different formulas employed for calculation of consumption rate influenced preference ranking in the no- and four-choice designs but not the two-choice design.

Determinants of Healthcare Expenditure in Economic Cooperation Organization (ECO) Countries: Evidence from Panel Cointegration Tests.

PubMed

Samadi, Alihussein; Homaie Rad, Enayatollah

2013-06-01

Over the last decade there has been an increase in healthcare expenditures while at the same time the inequity in distribution of resources has grown. These two issues have urged the researchers to review the determinants of healthcare expenditures. In this study, we surveyed the determinants of health expenditures in Economic Cooperation Organization (ECO) countries. We used Panel data econometrics methods for the purpose of this research. For long term analysis, we used Pesaran cross sectional dependency test followed by panel unit root tests to show first whether the variables were stationary or not. Upon confirmation of no stationary variables, we used Westerlund panel cointegration test in order to show whether long term relationships exist between the variables. At the end, we estimated the model with Continuous-Updated Fully Modified (CUP-FM) estimator. For short term analysis also, we used Fixed Effects (FE) estimator to estimate the model. A long term relationship was found between the health expenditures per capita and GDP per capita, the proportion of population below 15 and above 65 years old, number of physicians, and urbanisation. Besides, all the variables had short term relationships with health expenditures, except for the proportion of population above 65 years old. The coefficient of GDP was below 1 in the model. Therefore, health is counted as a necessary good in ECO countries and governments must pay due attention to the equal distribution of health services in all regions of the country.

Determinants of Healthcare Expenditure in Economic Cooperation Organization (ECO) Countries: Evidence from Panel Cointegration Tests

PubMed Central

Samadi, Alihussein; Homaie Rad, Enayatollah

2013-01-01

Background: Over the last decade there has been an increase in healthcare expenditures while at the same time the inequity in distribution of resources has grown. These two issues have urged the researchers to review the determinants of healthcare expenditures. In this study, we surveyed the determinants of health expenditures in Economic Cooperation Organization (ECO) countries. Methods: We used Panel data econometrics methods for the purpose of this research. For long term analysis, we used Pesaran cross sectional dependency test followed by panel unit root tests to show first whether the variables were stationary or not. Upon confirmation of no stationary variables, we used Westerlund panel cointegration test in order to show whether long term relationships exist between the variables. At the end, we estimated the model with Continuous-Updated Fully Modified (CUP-FM) estimator. For short term analysis also, we used Fixed Effects (FE) estimator to estimate the model. Results: A long term relationship was found between the health expenditures per capita and GDP per capita, the proportion of population below 15 and above 65 years old, number of physicians, and urbanisation. Besides, all the variables had short term relationships with health expenditures, except for the proportion of population above 65 years old. Conclusion: The coefficient of GDP was below 1 in the model. Therefore, health is counted as a necessary good in ECO countries and governments must pay due attention to the equal distribution of health services in all regions of the country. PMID:24596838

Effects of radio transmitters on migrating wood thrushes

USGS Publications Warehouse

Powell, L.A.; Krementz, D.G.; Lang, J.D.; Conroy, M.J.

1998-01-01

We quantified the effects of radio transmitters on Wood Thrushes (Hylocichla mustelina) using 4 yr of banding and telemetry data from Piedmont National Wildlife Refuge, Georgia. Flight performance models suggest that the 1.6-g transmitter shortens the migratory range of Wood Thrushes by only 60 km, and the estimated migratory range is adequate to accomplish migration even with limited fat stores. We used two strengths of line, 5- and 9-kg test-strength braided Dacron, to attach the transmitters using the thigh-harness method. We recaptured 13 returning radio-marked Wood Thrushes, seven of which were still marked. Six of the seven birds marked with the 5-kg test harnesses lost their transmitters within 1 yr while all six of the 9-kg test harnesses were still attached up to 21 mo later. Radio-marking did not reduce the return rates of adults and immatures, and the transmitters did not cause radio-marked birds to lose more mass than banded-only birds. Wood Thrushes can successfully carry a transmitter during migration with no detectable negative effects. We recommend continued use of the thigh-harness method, but we encourage the use of 5-kg cotton line.

Analysis of soy flour/phenol-formaldehyde adhesives for bonding wood

Treesearch

Linda Lorenz; Charles R. Frihart; James M. Wescott

2005-01-01

The desire to make more environmentally friendly and lower-cost bonded wood products has led to an interest in replacing some phenol and formaldehyde in wood adhe- sives with soybean flour. It is important to develop tests that relate resin production variables to resin properties before and after wood bonding. The protein needs to be denatured, with minimal hydrolysis...

Environmental impact of preservative-treated wood in a wetland boardwalk.

Treesearch

Stan T. Lebow; Patricia K. Lebow; Daniel O. Foster; Kenneth M. Brooks

Forest Service, Bureau of Land Management, and industry partners are cooperating in a study of the leaching and environmental effects of a wetland boardwalk. The construction project is considered bworst casec because the site has high rainfall and large volumes of treated wood were used. Separate boardwalk test sections were constructed using untreated wood or wood...

Advanced Solar Panel Designs

NASA Technical Reports Server (NTRS)

Ralph, E. L.; Linder, E. B.

1995-01-01

Solar panel designs that utilize new high-efficiency solar cells and lightweight rigid panel technologies are described. The resulting designs increase the specific power (W/kg) achievable in the near-term and are well suited to meet the demands of higher performance small satellites (smallsats). Advanced solar panel designs have been developed and demonstrated on two NASA SBIR contracts at Applied Solar. The first used 19% efficient, large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells with a lightweight rigid graphite epoxy isogrid substrate configuration. A 1,445 sq cm coupon was fabricated and tested to demonstrate 60 W/kg with a high potential of achieving 80 W/kg. The second panel design used new 22% efficiency, dual-junction GaInP2/GaAs/Ge solar cells combined with a lightweight aluminum core/graphite fiber mesh facesheet substrate. A 1,445 sq cm coupon was fabricated and tested to demonstrate 105 W/kg with the potential of achieving 115 W/kg.

Wood-related occupations, wood dust exposure, and sinonasal cancer.

PubMed

Hayes, R B; Gerin, M; Raatgever, J W; de Bruyn, A

1986-10-01

A case-control study was conducted to examine the relations between type of woodworking and the extent of wood dust exposure to the risks for specific histologic types of sinonasal cancer. In cooperation with the major treatment centers in the Netherlands, 116 male patients newly diagnosed between 1978 and 1981 with primary malignancies of epithelial origin of this site were identified for study. Living controls were selected from the municipal registries, and deceased controls were selected from the national death registry. Interviews were completed for 91 (78%) cases and 195 (75%) controls. Job histories were coded by industry and occupation. An index of exposure was developed to classify the extent of occupational exposure to wood dust. When necessary, adjustment was made for age and usual cigarette use. The risk for nasal adenocarcinoma was elevated by industry for the wood and paper industry (odds ratio (OR) = 11.9) and by occupation for those employed in furniture and cabinet making (OR = 139.8), in factory joinery and carpentry work (OR = 16.3), and in association with high-level wood dust exposure (OR = 26.3). Other types of nasal cancer were not found to be associated with wood-related industries or occupations. A moderate excess in risk for squamous cell cancer (OR = 2.5) was associated with low-level wood dust exposure; however, no dose-response relation was evident. The association between wood dust and adenocarcinoma was strongest for those employed in wood dust-related occupations between 1930 and 1941. The risk of adenocarcinoma did not appear to decrease for at least 15 years after termination of exposure to wood dust. No cases of nasal adenocarcinoma were observed in men whose first exposure to wood dust occurred after 1941.

LEACHING OF CCA-TREATED WOOD: IMPLICATIONS FOR WASTE DISPOSAL

EPA Science Inventory

Leaching of arsenic, chromium, and copper from chromated copper arsenate (CCA)-treated wood poses possible environmental risk when disposed. Samples of un-weathered CCA-treated wood were tested using a variety of US regulatory leaching procedures, including the toxicity character...

Effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures

Treesearch

Andy W.C. Lee; Zhongli Hong; Douglas R. Phillips; Chung-Yun Hse

1987-01-01

This study investigated the effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures made from six wood species: southern pine, white oak, southern red oak, yellow-poplar, sweetgum, and hickory. Cement/wood ratios varied from 13/1 to 4/1. Wood storage conditions consisted of air-...

Wood preservation

Treesearch

Rebecca E. Ibach

2003-01-01

When wood is exposed to various environmental conditions, many degradation reactions (biological, ultraviolet, mechanical, moisture, and chemical) can occur. To protect wood from biological degradation, chemical preservatives are applied by nonpressure or pressure treatment. Penetration and retention of a chemical depend upon the wood species and the amount of...

Panel fabrication utilizing GaAs solar cells

NASA Technical Reports Server (NTRS)

Mardesich, N.

1984-01-01

The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

Cytochemical localization of cellulases in decayed and nondecayed wood

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murmanis, L.; Highley, T.L.; Palmer, J.G.

1987-01-01

Sawdust from undecayed western hemlock wood and from wood previously decayed by the brown-rot fungus Poria placenta or by the white-rot fungus Ganoderma applanatum was incubated with commercial cellulase from Trichoderma viride. Samples were treated cytochemically to locate cellulase activity and examined by TEM. Results showed that cellulase degraded undecayed wood extensively, with the attack starting on the outer border of a cell wall and progressing inside. Wood decayed by P. placenta, with or without cellulase incubation, and treated by the cytochemical test showed uniform distribution of electron dense particles throughout the cell walls. In wood decayed by G. applanatum,more » cellulase degradation was similar to that in undecayed wood. From measurements of particle diameter it is suggested that electron dense particles are cellulase. It is concluded that brown-rot and white-rot fungi have different effects on the microstructure of wood. The brown-rot fungus appears to open the wood microstructure so that cellulase can diffuse throughout the degraded tracheid wall.« less

Cantilever Beam Static and Dynamic Response Comparison with Mid-Point Bending for Thin MDF composite Panels

Treesearch

John F. Hunt; Houjiang Zhang; Zhiren Guo; Feng Fu

2013-01-01

A new cantilever beam apparatus has been developed to measure static and vibrational properties of small and thin samples of wood or composite panels. The apparatus applies a known displacement to a cantilever beam, measures its static load, then releases it into its natural first mode of transverse vibration. Free vibrational tip displacements as a function of time...

Instrumental intelligent test of food sensory quality as mimic of human panel test combining multiple cross-perception sensors and data fusion.

PubMed

Ouyang, Qin; Zhao, Jiewen; Chen, Quansheng

2014-09-02

Instrumental test of food quality using perception sensors instead of human panel test is attracting massive attention recently. A novel cross-perception multi-sensors data fusion imitating multiple mammal perception was proposed for the instrumental test in this work. First, three mimic sensors of electronic eye, electronic nose and electronic tongue were used in sequence for data acquisition of rice wine samples. Then all data from the three different sensors were preprocessed and merged. Next, three cross-perception variables i.e., color, aroma and taste, were constructed using principal components analysis (PCA) and multiple linear regression (MLR) which were used as the input of models. MLR, back-propagation artificial neural network (BPANN) and support vector machine (SVM) were comparatively used for modeling, and the instrumental test was achieved for the comprehensive quality of samples. Results showed the proposed cross-perception multi-sensors data fusion presented obvious superiority to the traditional data fusion methodologies, also achieved a high correlation coefficient (>90%) with the human panel test results. This work demonstrated that the instrumental test based on the cross-perception multi-sensors data fusion can actually mimic the human test behavior, therefore is of great significance to ensure the quality of products and decrease the loss of the manufacturers. Copyright © 2014 Elsevier B.V. All rights reserved.

Structure-Property Characterization of the Crinkle-Leaf Peach Wood Phenotype: A Future Model System for Wood Properties Research?

NASA Astrophysics Data System (ADS)

Wiedenhoeft, Alex C.; Arévalo, Rafael; Ledbetter, Craig; Jakes, Joseph E.

2016-09-01

Nearly 400 million years of evolution and field-testing by the natural world has given humans thousands of wood types, each with unique structure-property relationships to study, exploit, and ideally, to manipulate, but the slow growth of trees makes them a recalcitrant experimental system. Variations in wood features of two genotypes of peach ( Prunus persica L.) trees, wild-type and crinkle-leaf, were examined to elucidate the nature of weak wood in crinkle-leaf trees. Crinkle-leaf is a naturally-occurring mutation in which wood strength is altered in conjunction with an easily observed `crinkling' of the leaves' surface. Trees from three vigor classes (low growth rate, average growth rate, and high growth rate) of each genotype were sampled. No meaningful tendency of dissimilarities among the different vigor classes was found, nor any pattern in features in a genotype-by-vigor analysis. Wild-type trees exhibited longer vessels and fibers, wider rays, and slightly higher specific gravity. Neither cell wall mechanical properties measured with nanoindentation nor cell wall histochemical properties were statistically or observably different between crinkle-leaf and wild-type wood. The crinkle-leaf mutant has the potential to be a useful model system for wood properties investigation and manipulation if it can serve as a field-observable vegetative marker for altered wood properties.

Flight Test of a Technology Transparent Light Concentration Panel on SMEX/WIRE

NASA Technical Reports Server (NTRS)

Stern, Theodore G.; Lyons, John

2000-01-01

A flight experiment has demonstrated a modular solar concentrator that can be used as a direct substitute replacement for planar photovoltaic panels in spacecraft solar arrays. The Light Concentrating Panel (LCP) uses an orthogrid arrangement of composite mirror strips to form an array of rectangular mirror troughs that reflect light onto standard, high-efficiency solar cells at a concentration ratio of approximately 3:1. The panel area, mass, thickness, and pointing tolerance has been shown to be similar to a planar array using the same cells. Concentration reduces the panel's cell area by 2/3, which significantly reduces the cost of the panel. An opportunity for a flight experiment module arose on NASA's Small Explorer / Wide-Field Infrared Explorer (SMEX/WIRE) spacecraft, which uses modular solar panel modules integrated into a solar panel frame structure. The design and analysis that supported implementation of the LCP as a flight experiment module is described. Easy integration into the existing SMEX-LITE wing demonstrated the benefits of technology transparency. Flight data shows the stability of the LCP module after nearly one year in Low Earth Orbit.

Fatigue test of a fiberglass based composite panel. Increasing the lifetime of freight wagon

NASA Astrophysics Data System (ADS)

Sobek, M.; Baier, A.; Grabowski, Ł.; Majzner, M.

2016-08-01

In the XXI century transportation of goods plays a key role in the economy. Due to a good logistics the economy is able to grow fluently. Although land transportation is carried out mainly through trucks for the last several years there has been noted an increase in the percentage share of rail transport in the freight transport. The main goods transported by railways are mineral fuels, mining and quarrying products. They constitute the greater part of 70% of total transported goods. Transportation of material of such high weight, high hardness and with different shapes involves increased and accelerated wear and tear of the cargo space of the wagon. This process is also magnified by substances used to prevent overheating or goods theft. Usually they are in the form of chemical compounds powder, eg. Calcium. A very large impact on the wear of the freight wagons hull is made because of mechanical damage. Their source comes mostly from loading cargo with impetus and using heavy machines during unloading. A large number of cycles of loading and unloading during the working period causes abrasion of body and as a result after several years a wagon car qualifies for a major maintenance. Possibility of application composite panels in the process of renovating the wagons body could reduce the weight of whole train and prolong the service life between mandatory technical inspection. The Paper "Fatigue test of a fiberglass based composite panel. Increasing the lifetime of freight wagon" presents the research process and the results of the endurance test of the composite panel samples fixed to a metal plate. As a fixing method a stainless steel rivet nut and a stainless steel button head socket screws were chosen. Cyclic and multiple load were applied to test samples using a pneumatic cylinder. Such a methodology simulated the forces resulting from loading and unloading of the wagon and movement of the cargo during transport. In the study a dedicated stand equipped with a

Structure–property characterization of the crinkle-leaf peach wood phenotype: a future model system for wood properties research?

Treesearch

Alex C. Wiedenhoeft; Rafael Arévalo; Craig Ledbetter; Joseph E. Jakes

2016-01-01

Nearly 400 million years of evolution and field-testing by the natural world has given humans thousands of wood types, each with unique structure– property relationships to study, exploit, and ideally, to manipulate, but the slow growth of trees makes them a recalcitrant experimental system. Variations in wood features of two genotypes of peach (Prunus persica L.)...

Advanced solar panel designs

NASA Technical Reports Server (NTRS)

Ralph, E. L.; Linder, E. B.

1996-01-01

Solar panel designs that utilize new high-efficiency solar cells and lightweight rigid panel technologies are described. The resulting designs increase the specific power (W/kg) achievable in the near-term and are well suited to meet the demands of higher performance small satellites (smallsats). Advanced solar panel designs have been developed and demonstrated on two NASA SBIR contracts at Applied Solar. The first used 19% efficient, large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells with a lightweight rigid graphite epoxy isogrid substrate configuration. A 1,445 cm(exp 2) coupon was fabricated and tested to demonstrate 60 W/kg with a high potential of achieving 80 W/kg. The second panel design used new 22% efficiency, dual junction GaInP2/GaAs/Ge solar cells combined with a lightweight aluminum core/graphite fiber mesh facesheet substrate. A 1,445 cm(exp 2) coupon was fabricated and tested to demonstrate 105 W/kg with the potential of achieving 115 W/kg. This paper will address the construction details for the GaAs/isogrid and dual-junction GaAs/carbon mesh panel configurations. These are ultimately sized to provide 75 Watts and 119 Watts respectively for smallsats or may be used as modular building blocks for larger systems. GaAs/isogrid and dual-junction GaAs/carbon mesh coupons have been fabricated and tested to successfully demonstrate critical performance parameters and results are also provided here.

Wood as an adherend

Treesearch

Bryan H. River; Charles B. Vick; Robert H. Gillespie

1991-01-01

Wood is a porous, permeable, hygroscopic, orthotropic, biological composite material of extreme chemical diversity and physical intricacy. Table 1.1 provides an overview of the may variables, including wood variables, that bear on the bonding and performance of wood in wood joints and wood-based materials. Of particular note is the fact that wood properties vary...

Projected wood energy impact on US forest wood resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skog, K.E.

1993-12-31

The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price ofmore » wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).« less

Fabrication and Testing of Carbon Fiber, Graphite-Epoxy Panels for Submillimeter Telescope Use

NASA Astrophysics Data System (ADS)

Rieger, H.; Helwig, G.; Parks, R. E.; Ulich, B. L.

1983-12-01

An experimental carbon-fiber, graphite-epoxy, aluminum Flexcore sandwich panel roughly 1-m square was made by Dornier System, Friedrichshafen, West Germany. The panel was a pre-prototype of the panels to be used in the dish of the 10-m diameter Sub-Millimeter Telescope, a joint project of the Max-Planck-Institute fur Radioastronomie, Bonn, West Germany, and Steward Observatory, the University of Arizona in Tucson. This paper outlines the fabrication process for the panel and indicates the surface accuracy of the panel replication process. To predict the behavior of the panel under various environmental loads, the panel was modeled structurally using anisotropic elements for the core material. Results of this analysis along with experimental verification of these predictions are also given.

Decay of wood and wood-based products above ground in buildings

Treesearch

Charles G. Carll; Terry L. Highley

1999-01-01

This paper is an overview of what we know about occurrence of wood decay above ground within buildings. It presents information concerning under what conditions decay may become established. In laboratory tests involving optimum moisture and temperature conditions for decay fungi, and direct contact with large quantities of specific well-developed decay...

Wood Export and Deposition Dynamics in Mountain Watersheds

NASA Astrophysics Data System (ADS)

Senter, Anne Elizabeth

conditions and accompanying hydrologic responses. Chapter 2 contains development of new theory in support of the introduction of multiplicative coefficients, categorized by water year type, that were used to predict wood export quantities via utilization of an existing discharge-based theoretical equation. This new theory was the product of continued investigations into watershed-scale factors in search of explanation of observed variation of wood export rates into New Bullards Bar Reservoir. The gap between known variability and the attribution of wood export to one hydrologic relation continues to be a persistent issue, as the hierarchical and stochastic temporal and spatial nature of wood budget components remain difficult to quantify. The development of "watershed processes" coefficients was specifically focused on a generalized, parsimonious approach using water year type categories, with validation exercises supporting the approach. In dry years, predictions more closely represented observed wood export quantities, whereas the previously derived annual peak discharge relation yielded large over-predictions. Additional data are needed to continue development of these watershed-specific coefficients. This new approach to wood export prediction may be beneficial in regulated river systems for planning purposes, and its efficacy could be tested in other watersheds. Chapter 3 presents the results of an investigation into wood deposition mechanisms in a 12.2 km segment of the confined, bedrock-dominated South Yuba River watershed. Inclusion of coarse wood particles in the analyses was essential in recognizing depositional patterns, thus supporting the value of utilizing a wider wood-size range. A near-census data collection effort yielded myriad data, of which topographic wetted width and bed elevation data, developed for an observed 4.5-year flood event, were standardized in 10-m intervals and then univariate and linked values were ordered into landform classifications

The Fungal Degradation of Wood and Wood Products Selected Bibliography

DTIC Science & Technology

1981-08-01

Pi 0-Alt^Jihi 1 TECHNICAL LIBRARY SPECIAL PUBLICATION ARLCD-SP-81006 THE FUNGAL DEGRADATION OF WOOD AND WOOD PRODUCTS SELECTED BIBLIOGRAPHY...GOVT ACCESSION NO. READ INSTRUCTIONS BEFORE COMPLETING FORM 3. RECIPIENT’S CATALOG NUMBER 4. TITLE fand SubJltJo; THE FUNGAL DEGRADATION OF...search con- centrated on the microbiological deterioration or degradation of wood (trees) or wood products which are found or used in tropical

Comprehensive embryo testing. Experts' opinions regarding future directions: an expert panel study on comprehensive embryo testing.

PubMed

Hens, Kristien; Dondorp, Wybo J; Geraedts, Joep P M; de Wert, Guido M

2013-05-01

What do scientists in the field of preimplantation genetic diagnosis (PGD) and preimplantation genetic screening (PGS) consider to be the future direction of comprehensive embryo testing? Although there are many biological and technical limitations, as well as uncertainties regarding the meaning of genetic variation, comprehensive embryo testing will impact the IVF/PGD practice and a timely ethical reflection is needed. Comprehensive testing using microarrays is currently being introduced in the context of PGD and PGS, and it is to be expected that whole-genome sequencing will also follow. Current ethical and empirical sociological research on embryo testing focuses on PGD as it is practiced now. However, empirical research and systematic reflection regarding the impact of comprehensive techniques for embryo testing is missing. In order to understand the potential of this technology and to be able to adequately foresee its implications, we held an expert panel with seven pioneers in PGD. We conducted an expert panel in October 2011 with seven PGD pioneers from Belgium, The Netherlands, Germany and the UK. Participants expected the use of comprehensive techniques in the context of PGD. However, the introduction of these techniques in embryo testing requires timely ethical reflection as it involves a shift from choosing an embryo without a particular genetic disease (i.e. PGD) or most likely to result in a successful pregnancy (i.e. PGS) to choosing the best embryo based on a much wider set of criteria. Such ethical reflection should take account of current technical and biological limitations and also of current uncertainties with regard to the meaning of genetic variance. However, ethicists should also not be afraid to look into the future. There was a general agreement that embryo testing will be increasingly preceded by comprehensive preconception screening, thus enabling smart combinations of genetic testing. The group was composed of seven participants from

Finishing of wood