Is There a "Workable" Race-Neutral Alternative to Affirmative Action in College Admissions?

ERIC Educational Resources Information Center

Long, Mark C.

2015-01-01

The 2013 decision by the U.S. Supreme Court in the Fisher v. University of Texas at Austin case clarified when and how it is legally permissible for universities to use an applicant's race or ethnicity in its admissions decisions. The court concluded that such use is permissible when "no workable race-neutral alternatives would produce…

Effects of TEA·HCl hardening accelerator on the workability of cement-based materials

NASA Astrophysics Data System (ADS)

Pan, Wenhao; Ding, Zhaoyang; Chen, Yanwen

2017-03-01

The aim of the test is to research the influence rules of TEA·HCl on the workability of cement paste and concrete. Based on the features of the new hardening accelerator, an experimental analysis system were established through different dosages of hardening accelerator, and the feasibility of such accelerator to satisfy the need of practical engineering was verified. The results show that adding of the hardening accelerator can accelerate the cement hydration, and what’s more, when the dosage was 0.04%, the setting time was the shortest while the initial setting time and final setting time were 130 min and 180 min, respectively. The initial fluidity of cement paste of adding accelerator was roughly equivalent compared with that of blank. After 30 min, fluidity loss would decrease with the dosage increasing, but fluidity may increase. The application of the hardening accelerator can make the early workability of concrete enhance, especially the slump loss of 30 min can improve more significantly. The bleeding rate of concrete significantly decreases after adding TEA·HCl. The conclusion is that the new hardening accelerator can meet the need of the workability of cement-based materials in the optimum dosage range.

Poly(carboxylate ether)-based superplasticizer achieves workability retention in calcium aluminate cement

NASA Astrophysics Data System (ADS)

Akhlaghi, Omid; Menceloglu, Yusuf Ziya; Akbulut, Ozge

2017-01-01

Calcium aluminate cement (CAC) suffers from loss of workability in less than an hour (~15 minutes) after first touch of water. Current superplasticizers that are utilized to modify the viscosity of cement admixtures are designed to target ordinary Portland cement (OPC). The high affinity between these superplasticizers and cement particles were found to be detrimental in CAC systems. Utilization of a monomer that, instead, facilitates gradual adsorption of a superplasticizer provides workability retention. For the first time in literature, we report a superplasticizer that caters to the properties of CAC such as high rate of surface development and surface charge. While neat CAC was almost unworkable after 1 hour, with the addition of only 0.4% of the optimized superplasticizer, 90% fluidity retention was achieved.

Design and Implementation of the PMS Module for ’Argos’

DTIC Science & Technology

1989-12-01

designing , and implementing a fully workable Planned Maintenance System (PMS). This implementation demonstrates both the capabilities and benefits such a...analyzing, designing , and implementing a fully workable Planned Maintenance System (PMS). This implementation demonstrates both the capabilities and... design and implementation. PMS is the system developed by the navy to provide each ship, department, and supervisor with the tools needed to plan

Workability of Safety Education and Training for Workers' Strategy in Accident Reduction in Selected Manufacturing Industries in Lagos State

ERIC Educational Resources Information Center

Ayodele, Rachael B.; Olubayo-Fatiregun, Martina A.

2013-01-01

This study determined the workability of Safety Education and Training for Workers' strategy in reducing accidents. A descriptive survey research design was used. A total of 20 Managerial staff with mean work experience of 13.5 years was selected from 10 manufacturing industries in Lagos State, using intact group method. They were 100% males. Data…

Hearing loss and work participation: a cross-sectional study in Norway.

PubMed

Svinndal, Elisabeth Vigrestad; Solheim, Jorunn; Rise, Marit By; Jensen, Chris

2018-04-27

To study work participation of persons with hearing loss, and associations with hearing disabilities, self-reported workability, fatigue and work accommodation. Cross-sectional internet-based survey. A total of 10,679 persons with hearing loss within working-age were invited to answer the survey, where 3330 answered (35.6%). Degree of hearing loss was associated with low workability, fatigue and work place accommodation, while sick leave was associated with fatigue. Degree of hearing loss was positively associated with being unemployed (p < .001) and having part-time work (p < .01) (often combined with disability benefits) for women. Work place accommodation was more frequently provided among respondents working with sedentary postures, high seniority, long-term sick leave or low workability. Additional unfavourable sensory conditions were associated with decreased employment (p < .001) and workability, and an increase in sick leave (p < .01) and fatigue (p < .001). Hearing loss seemed to influence work participation factors negatively; particularly, for moderate hearing loss and for women, even though the degree of employment was high. A lack of work place accommodation when there was a need for such was found. This implies increased attentiveness towards individual needs concerning the experienced disability a hearing loss may produce. A more frequent use of hearing disability assessment is suggested.

Effect of palm oil fuel ash on compressive strength of palm oil boiler stone lightweight aggregate concrete

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Zamri, N. A.; Kusbiantoro, A.; Lim, N. H. A. S.; Ariffin, M. A. Mohd

2018-04-01

Both palm oil fuel ash (POFA) and palm oil boiler stone (POBS) are by-products which has been continuously generated by local palm oil mill in large amount. Both by products is usually disposed as profitless waste and considered as nuisance to environment. The present research investigates the workability and compressive strength performance of lightweight aggregate concrete (LWAC) made of palm oil boiler stone (POBS) known as palm oil boiler stone lightweight aggregate concrete (POBS LWAC) containing various content of palm oil fuel ash. The control specimen that is POBS LWAC of grade 60 were produced using 100% OPC. Then, another 4 mixes were prepared by varying the POFA percentage from 10%, 20%, 30% and 40% by weight of cement. Fresh mixes were subjected to slump test to determine its workability before casted in form of cubes. Then, all specimens were subjected to water curing up to 28 days and then tested for its compressive strength. It was found out that utilizing of optimum amount of POFA in POBS LWAC would improve the workability and compressive strength of the concrete. However, inclusion of POFA more than optimum amount is not recommended as it will increase the water demand leading to lower workability and strength reduction.

The effect of slag addition on strength development of Class C fly ash geopolymer concrete at normal temperature

NASA Astrophysics Data System (ADS)

Wardhono, Arie; Law, David W.; Sutikno, Dani, Hasan

2017-09-01

This paper presents the effect of slag addition on strength development and workability of fly ash/slag based geopolymer (FASLG) concrete cured at normal temperature. Class C fly ash with high ferrite (Fe) content was used as the primary material. The proportions of fly ash (FA) to slag (SL) are: 1 FA : 0 SL, 0.9 FA : 0.1 SL, 0.7 FA : 0.3 SL, and 0.5 FA : 0.5 SL. The workability and strength properties were determined by slump, vikat, and compressive strength tests. The result shows that the highest compressive strength was achieved by FASLG-3 concrete with 30% slag addition and exhibited a comparable strength to that normal concrete at 28 days. The 30% slag addition also improve the workability and increase the setting time of FASLG concrete specimens. It can be concluded that the slag inclusion on fly ash will improve the performance of geopolymer concrete at normal temperature.

Effect of yttrium on martensite-austenite phase transformation temperatures and high temperature oxidation kinetics of Ti-Ni-Hf high-temperature shape memory alloys

NASA Astrophysics Data System (ADS)

Kim, Jeoung Han; Kim, Kyong Min; Yeom, Jong Taek; Young, Sung

2016-03-01

The effect of yttrium (< 5.5 at%) on the martensite-austenite phase transformation temperatures, microstructural evolution, and hot workability of Ti-Ni-Hf high-temperature shape memory alloys is investigated. For these purposes, differential scanning calorimetry, hot compression, and thermo-gravimetric tests are conducted. The phase transformation temperatures are not noticeably influenced by the addition of yttrium up to 4.5 at%. Furthermore, the hot workability is not significantly affected by the yttrium addition up to 1.0 at%. However, when the amount of yttrium addition exceeds 1.0 at%, the hot workability deteriorates significantly. In contrast, remarkable improvement in the high temperature oxidation resistance due to the yttrium addition is demonstrated. The total thickness of the oxide layers is substantially thinner in the Y-added specimen. In particular, the thickness of (Ti,Hf) oxide layer is reduced from 200 µm to 120 µm by the addition of 0.3 at% Y.

Workability enhancement of geopolymer concrete through the use of retarder

NASA Astrophysics Data System (ADS)

Umniati, B. Sri; Risdanareni, Puput; Zein, Fahmi Tarmizi Zulfikar

2017-09-01

Geopolymer concrete is a type of concrete manufactured without the addition of cement. In geopolymer concrete, along with an activator, cement as the concrete binder can be replaced by the fly ash. This will reduce global demand on cement, and therefore will reduce CO2 emission due to cement production. Thus, geopolymer concrete is commonly known as an eco-friendly concrete. Geopolymer concrete also offers a solution concerning with the utilization of the fly ash waste. However, despite of its environmental advantages, geopolymer concrete has a drawback, namelygeopolymer concrete set quickly, thus reducing its workability. This research aimed to increase the workability of geopolymer concrete by using retarder admixture (Plastocrete RT6 Plus). Retarder used varies within 0.2%, 0.4% and 0.6% of fly ash mass. As a control, geopolymer concrete without retarder (0%) were also made. Activator used in this research was Na2SiO3 mixed with NaOH 10 M solution, with ratio of 1:5. The results showed an optimum composition of geopolymer concrete with 0.6% retarder, where initial setting time occured after 6.75 hours, and the final setting time reached after 9.5 hours. Moreover, the slump of the geopolymer concrete was 8.8 cm, and the slump flow was 24 cm. The compressive strength of the geopolymer concrete at 28 days was 47.21 MPa. The experiment showed that the more retarder added, the setting time of the geopolymer concrete will be increased, thus increasing its workability.

Psychological well-being and workability in child abuse investigators.

PubMed

Tehrani, N

2018-05-17

Working with victims and offenders of child abuse can impact on the health and well-being of police officers and staff. To identify the effects of tenure, work ability, gender and a personal experience of child abuse on symptoms of anxiety, depression and primary and secondary trauma in child abuse investigators (CAIs). Screening questionnaires were sent to police officers and staff. The officers and staff worked in child protection in seven police forces. The surveillance was undertaken online and the data were encrypted and personal identifiers removed. The four clinical measures were Goldberg Anxiety/Depression Scale, Professional Quality of Life and Impact of Events (extended). Eighty-two per cent of 2798 CAIs returned questionnaires. There was a statistically significant relationship between all four clinical symptoms and workability (P < 0.001), between tenure and primary trauma (P < 0.01) and between anxiety, depression, primary trauma and workability and adverse childhood experience (ACE) scores (P < 0.001). Regression analysis showed that workability, tenure and ACE scores explained between 12 and 23% of the variance. There were gender differences with women having higher levels of symptoms; however, the effect size and clinical significance were negligible for all but the primary trauma scores. Psychological surveillance can provide an important source of evidence for occupational health practitioners working with CAIs in informing them of the factors which could be considered in selecting, training, supporting and retaining officers and staff. Psychological surveillance can also help police management to identify ways to monitor the long-term effectiveness and well-being of CAIs.

Study on The Geopolymer Concrete Properties Reinforced with Hooked Steel Fiber

NASA Astrophysics Data System (ADS)

Abdullah, M. M. A. B.; Tahir, M. F. M.; Tajudin, M. A. F. M. A.; Ekaputri, J. J.; Bayuaji, R.; Khatim, N. A. M.

2017-11-01

In this research, Class F fly ash and a mixture of alkaline activators and different amount of hooked steel fiber were used for preparing geopolymer concrete. In order to analyses the effect of hooked steel fiber on the geopolymer concrete, the analysis such as chemical composition of fly ash, workability of fresh geopolymer, water absorption, density, compressive strength of hardened geopolymer concrete have been carried out. Mixtures were prepared with fly ash to alkaline liquid ratio of 2.0 with hooked steel fibers were added to the mix with different amounts which are 1%, 3%, 5% and 7% by the weight of the concrete. Experimental results showed that the compressive strength of geopolymer concrete increases as the hooked steel fibers increases. The optimum compressive strength obtained was up to 87.83 MPa on the 14th day. The density of geopolymer concrete are in the range between 2466 kg/m3 to 2501 kg/m3. In addition, the workability value of geopolymer without hooked steel fibers is 100 mm while the workability value of geopolymer with hooked steel fibers are between 60 mm to 30 mm.

Specialized mechanical properties of pure aluminum by using non-equal channel angular pressing for developing its electrical applications

NASA Astrophysics Data System (ADS)

Fereshteh-Saniee, Faramarz; Asgari, Mohammad; Fakhar, Naeimeh

2016-08-01

Despite valuable electrical characteristics, the use of pure aluminum in different applications has been limited due to its low strength. Non-equal channel angular pressing (NECAP) is a recently proposed severe plastic deformation process with greater induced plastic strain and, consequently, better grain refinement in the product, compared with the well-known equal channel angular pressing technique. This research is concerned with the effects of the process temperature and ram velocity on the mechanical, workability and electrical properties of AA1060 aluminum alloy. Increasing the process temperature can concurrently increase the workability, ductility and electrical conductivity, while it has a reverse influence on the strength of the NECAPed specimen, although the strengths of all the products are higher than the as-received alloy. The influence of the ram speed on the mechanical properties of the processed samples is lower than the process temperature. Finally, a compromised process condition is introduced in order to attain a good combination of workability and strength with well-preserved electrical conductivity for electrical applications of components made of pure aluminum.

Visualization of Concrete Slump Flow Using the Kinect Sensor

PubMed Central

Park, Minbeom

2018-01-01

Workability is regarded as one of the important parameters of high-performance concrete and monitoring it is essential in concrete quality management at construction sites. The conventional workability test methods are basically based on length and time measured by a ruler and a stopwatch and, as such, inevitably involves human error. In this paper, we propose a 4D slump test method based on digital measurement and data processing as a novel concrete workability test. After acquiring the dynamically changing 3D surface of fresh concrete using a 3D depth sensor during the slump flow test, the stream images are processed with the proposed 4D slump processing algorithm and the results are compressed into a single 4D slump image. This image basically represents the dynamically spreading cross-section of fresh concrete along the time axis. From the 4D slump image, it is possible to determine the slump flow diameter, slump flow time, and slump height at any location simultaneously. The proposed 4D slump test will be able to activate research related to concrete flow simulation and concrete rheology by providing spatiotemporal measurement data of concrete flow. PMID:29510510

The Effect of Graphene Oxide on Cement Mortar

NASA Astrophysics Data System (ADS)

Kjaernsmo, Henrik; Kakay, Samdar; Fossa, Kjell T.; Gronli, John

2018-05-01

This paper investigates the effect of water dispersed- and powder Graphene oxide (GO) nanoparticle on fresh cement mortar, microstructure and mechanical strength after 3,7, and 28 days of curing. These properties were studied by treating the cement mortar with 0.03 wt%, 0.05 wt%, and 0.2 wt% GO of the cement weight combined with 0.8wt % polycarboxylate superplasticizer. The results show that the workability decreases as increasing the content of water dispersed GO. The heat of hydration is increased for both types of GO systems. The percent air content in 0.03 wt% and 0.05 wt% GO is almost constant, but increased from 3.2 % to 4.9 % in 0.2 wt% water dispersed GO. The increased air content has effect on poor compaction and workability. GO has the potential of accelerating the hydration process and enhance the early mechanical strength (3 and 7 days), but the workability seems to diminish the mechanical strength after 28 days of curing, particularly for the highest content of water dispersed GO. No distinct influence of GO on the microstructure. The overall results showed that the impact of water dispersed GO was found out to be higher than the powder GO.

Influence of polymer fibers on rheological properties of cement mortars

NASA Astrophysics Data System (ADS)

Malaszkiewicz, Dorota

2017-10-01

The reinforcing effect of fibers in cement composites often results in the improvement of the brittle nature of cementitious materials. But the decrease in the workability of fresh concrete is often the disadvantage of fibers addition. Conventional single-point workability tests cannot characterize workability of concrete in terms of fundamental rheological parameters. To this end, this paper describes an investigation of the influence of synthetic fiber additions (fiber length in the range 12-50 mm and volume fraction in the range 0-4%) on the rheological properties of fiber reinforced fresh mortar (FRFM) and development of these properties over time. The rheometer Viskomat XL was used in this study. Within the limitations of the instrument and testing procedure it is shown that FRFMs conform to the Bingham model. Natural postglacial sand 0/4 mm was used as a fine aggregate and cement CEMI 42.5 R was used as a binder. Three commercial synthetic fibers were selected for these examinations. Rheological properties were expressed in terms of Bingham model parameters g (yield value ) and h (plastic viscosity). Based on the test results it was found out that the fiber type and volume fraction affected both the yield stress and plastic viscosity.

Visualization of Concrete Slump Flow Using the Kinect Sensor.

PubMed

Kim, Jung-Hoon; Park, Minbeom

2018-03-03

Workability is regarded as one of the important parameters of high-performance concrete and monitoring it is essential in concrete quality management at construction sites. The conventional workability test methods are basically based on length and time measured by a ruler and a stopwatch and, as such, inevitably involves human error. In this paper, we propose a 4D slump test method based on digital measurement and data processing as a novel concrete workability test. After acquiring the dynamically changing 3D surface of fresh concrete using a 3D depth sensor during the slump flow test, the stream images are processed with the proposed 4D slump processing algorithm and the results are compressed into a single 4D slump image. This image basically represents the dynamically spreading cross-section of fresh concrete along the time axis. From the 4D slump image, it is possible to determine the slump flow diameter, slump flow time, and slump height at any location simultaneously. The proposed 4D slump test will be able to activate research related to concrete flow simulation and concrete rheology by providing spatiotemporal measurement data of concrete flow.

An Investigation into the Use of Manufactured Sand as a 100% Replacement for Fine Aggregate in Concrete.

PubMed

Pilegis, Martins; Gardner, Diane; Lark, Robert

2016-06-02

Manufactured sand differs from natural sea and river dredged sand in its physical and mineralogical properties. These can be both beneficial and detrimental to the fresh and hardened properties of concrete. This paper presents the results of a laboratory study in which manufactured sand produced in an industry sized crushing plant was characterised with respect to its physical and mineralogical properties. The influence of these characteristics on concrete workability and strength, when manufactured sand completely replaced natural sand in concrete, was investigated and modelled using artificial neural networks (ANN). The results show that the manufactured sand concrete made in this study generally requires a higher water/cement (w/c) ratio for workability equal to that of natural sand concrete due to the higher angularity of the manufactured sand particles. Water reducing admixtures can be used to compensate for this if the manufactured sand does not contain clay particles. At the same w/c ratio, the compressive and flexural strength of manufactured sand concrete exceeds that of natural sand concrete. ANN proved a valuable and reliable method of predicting concrete strength and workability based on the properties of the fine aggregate (FA) and the concrete mix composition.

An Investigation into the Use of Manufactured Sand as a 100% Replacement for Fine Aggregate in Concrete

PubMed Central

Pilegis, Martins; Gardner, Diane; Lark, Robert

2016-01-01

Manufactured sand differs from natural sea and river dredged sand in its physical and mineralogical properties. These can be both beneficial and detrimental to the fresh and hardened properties of concrete. This paper presents the results of a laboratory study in which manufactured sand produced in an industry sized crushing plant was characterised with respect to its physical and mineralogical properties. The influence of these characteristics on concrete workability and strength, when manufactured sand completely replaced natural sand in concrete, was investigated and modelled using artificial neural networks (ANN). The results show that the manufactured sand concrete made in this study generally requires a higher water/cement (w/c) ratio for workability equal to that of natural sand concrete due to the higher angularity of the manufactured sand particles. Water reducing admixtures can be used to compensate for this if the manufactured sand does not contain clay particles. At the same w/c ratio, the compressive and flexural strength of manufactured sand concrete exceeds that of natural sand concrete. ANN proved a valuable and reliable method of predicting concrete strength and workability based on the properties of the fine aggregate (FA) and the concrete mix composition. PMID:28773560

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Cindy Xiaohui; Lim, Chao Voon; Castagne, Sylvie

Titanium and its alloys have a wide range of applications in various industries such as aerospace, medical, automotive and even commercial products. However, formability of titanium alloys has always been an issue. This study presents the results of an investigation on the workability and response of Ti-6Al-4V deformed at different strain rates and lower elevated temperatures with different initial microstructures. Compression tests of cylindrical specimens were performed at various temperatures (300 deg. C, 400 deg. C, 450 deg. C, 500 deg. C) and at different strain rates (0.001 s{sup -1}, 0.02 s{sup -1} and 0.1 s{sup -1}). The effects ofmore » strain rate, temperature and initial microstructure on the workability of the Ti alloy were investigated. Based on these experimental results, workability maps for the respective initial microstructures were developed. Results showed that temperature played an important role in the formability of Ti-6Al-4V titanium alloys unlike strain rate. In addition, feasibility study on Multi-Directional Forging (MDF) was performed and positive results were obtained. It was demonstrated that Ti-6Al-4V titanium alloys can undergo severe plastic deformation at lower elevated temperature (400-500 deg. C) and at a higher strain rate of 0.1 s{sup -1}.« less

Effects of using blended binder of RHA and GGBS on the properties of concrete: A review

NASA Astrophysics Data System (ADS)

Ishak, Nuril Izzeaty; Johari, Megat Azmi Megat; Hashim, Syed Fuad Saiyid

2017-10-01

Concern about protecting and preserving the environment has driven many researchers to innovate the concrete materials in pursuing better mechanical and physical properties of the fresh and hardened concrete. This paper presents an overview of the microstructural properties, workability, and strength performance of concrete incorporated with mineral admixtures from rice husk ash (RHA) and ground granulated blast-furnace slag (GGBS). The substitution of these supplementary cementitious materials as a ternary blended binder concrete has also been included. It was found that, the average of RHA replacement in concrete is about 10%, while for GGBS is in the range of 40 to 50 % replacement of Portland cement. The results from previous studies yield to a better strength and could potentially be used as high performance concrete, but the high replacement with RHA decreased workability and required more water demand due to the micro porous character, high specific surface area and higher in carbon content of the material. Thus, the necessity of using superlasticizer is crucial to improve the workability and strength. The collection of comprehensive literatures elaborated that the usage of RHA and GGBS enhanced the properties of concrete while gives a better solution for the plenteous of waste produced from the agricultural and industrial sectors.

A chemical rationalization of the processing and application of the mortar coatings: Structural, thermodynamic, and fluorescence properties

NASA Astrophysics Data System (ADS)

Lima, Nathan B.; Rogerio, V. A.; Belarmino, Marcia K. D. L.; Silva, Anderson I. S.; Ioras, Renan U. F.; Oliveira, Romilde A.; Lima, Nathalia B. D.

2018-07-01

A chemical rationalization of the processing and application of the roughcast and plaster mortar coatings was advanced. The results revealed that the structural and thermodynamic nature of the hydrogen-bonded complexes between the inorganic precursors and water molecules are associated with the physical properties of both coatings. In this sense, the workability and curing time of the roughcast and the plaster mortars studied, seemingly, are related to the nature of the water solvation in the main components of these materials: calcium hydroxide and silicon dioxide. In addition, PM7 and PM7/COSMO results indicate that the enthalpy of solvation of water by hydrogen bonds in calcium hydroxide is stronger when compared with silicon dioxide systems. Therefore, the presence of free hydrated lime (calcium hydroxide) in the precursor mixture of plaster mortar leads to the large workability and elapsed curing time of this material. On the other hand, the absence of free hydrated lime in the precursor mixture of the roughcast mortar leads to its poor workability and faster elapsed curing time. Further, fluorescence microscopy experiments revealed that the inorganic compounds present in the cement precursor were transformed into different materials, that exhibit red and blue fluorescence. Finally, mechanical tests showed a tensile strength average 0.67 MPa for the plaster mortar material, whereas for the roughcast material is 0.53 MPa.

Digital image transformation and rectification of spacecraft and radar images

USGS Publications Warehouse

Wu, S.S.C.

1985-01-01

Digital image transformation and rectification can be described in three categories: (1) digital rectification of spacecraft pictures on workable stereoplotters; (2) digital correction of radar image geometry; and (3) digital reconstruction of shaded relief maps and perspective views including stereograms. Digital rectification can make high-oblique pictures workable on stereoplotters that would otherwise not accommodate such extreme tilt angles. It also enables panoramic line-scan geometry to be used to compile contour maps with photogrammetric plotters. Rectifications were digitally processed on both Viking Orbiter and Lander pictures of Mars as well as radar images taken by various radar systems. By merging digital terrain data with image data, perspective and three-dimensional views of Olympus Mons and Tithonium Chasma, also of Mars, are reconstructed through digital image processing. ?? 1985.

A Study of Tungsten-Technetium Alloys

NASA Technical Reports Server (NTRS)

Maltz, J. W.

1965-01-01

Technetium is a sister element to rhenium and has many properties that are similar to rhenium. It is predicted that technetium will have about the same effects on tungsten as rhenium in regard to increase in workability, lowered ductile to brittle transition temperature, and improved ductility. The objectives of the current work are to recover technetium from fission product wastes at Hanford Atomic Products Operation and reduce to purified metal; prepare W-Tc alloys containing up to 50 atomic% Tc; fabricate the alloy ingots to sheet stock, assessing the effect of technetium on workability; and perform metallurgical and mechanical properties evaluation of the fabricated alloys. Previous reports have described the separation and purification of 800 g of technetium metal powder, melting of technetium and W-Tc alloys, and some initial observation of the alloy material.

Influence of wood-derived biochar on the physico-mechanical and chemical characteristics of agricultural soils

NASA Astrophysics Data System (ADS)

Ahmed, Ahmed S. F.; Raghavan, Vijaya

2018-01-01

Amendment of soil with biochar has been shown to enhance fertility and increase crop productivity, but the specific influence of biochar on soil workability remains unclear. Select physico-mechanical and chemical properties of clay loam and sandy loam soils were measured after amendment with wood-derived biochar of two particle size ranges (0.5-425 and 425-850 µm) at five dosages ranging from 0.5 to 10% dry weight. Whereas the clay loam soil workability decreased when the finer wood-derived biochar was applied at rates of 6 or 10%, soil fertility was not enhanced. The sandy loam soil, due to Proctor compaction, significantly decreased in bulk density with 6 and 10% wood-derived biochar amendments indicating higher soil resistance to compaction.

Plotting a course from Paris

NASA Astrophysics Data System (ADS)

2015-12-01

A new climate agreement won't solve climate change, but it should nudge the world onto a lower-emissions path. Research must drive deeper transformations by translating proposed solutions into workable action.

A Theoretical Study of Microwave Beam Absorption by a Rectenna

NASA Technical Reports Server (NTRS)

Ott, J. H.; Rice, J. S.; Thorn, D. C.

1981-01-01

The theoretical operational parameters for the workable satellite power system were examined. The system requirements for efficient transmission and reception of an environmentally benign microwave beam were determined.

Developing a workable teacher identity: Building and negotiating identity within a professional network

NASA Astrophysics Data System (ADS)

Rostock, Roseanne

The challenge of attracting and retaining the next generation of teachers who are skilled and committed to meeting the growing demands of the profession is of increasing concern to researchers and policy makers, particularly since 45--50% of beginning teachers leave the profession within five years (Ingersoll & Smith, 2003). Reasons for such attrition include compensation, status and working conditions; however, there is growing evidence that a critical factor in new teacher retention hinges on teachers' ability to accomplish the difficult task of forming a workable professional identity in the midst of competing discourses about teaching (Alsup, 2006; Britzman, 2003). There is little research on professional identity development among those beginning teachers at highest risk for attrition (secondary math and science teachers, and those with strong academic backgrounds). This study explores the professional identity development of early-career math and science teachers who are part of the Knowles Science Teaching Foundation's (KSTF) teaching fellowship program, an external support network that aims to address many of the issues leading to high attrition among this particular population of teachers. Using narrative research methods, I examine three case studies of beginning teachers, exploring how they construct professional identity in relation to various discourse communities and negotiate tensions across multiple discourses. The cases identify both dominant discourses and counter-discourses that the teachers draw upon for important identity development resources. They also demonstrate that the way a teacher manages tensions across competing discourses is important to how well one can negotiate a workable professional identity. In particular, they emphasize the importance of engaging in borderland discourses (Gee, 1996) as a way of taking agency in one's own identity development as well as in transforming one's discourse communities. These cases shed light on how these beginning teachers work to negotiate a workable professional identity that may sustain them in a teaching career. In addition, they help us understand how a support network like KSTF can serve as a resource for helping new teachers construct professional identities, therefore addressing some of the issues that may lead to attrition among this population of new teachers.

Polymer concrete development.

DOT National Transportation Integrated Search

1974-02-01

Our work to date has involved working with aggregate gradations to minimize the voids and with different combinations of monomers, catalysts and promoters to achieve suitable strengths and workability. At present, tests are being made to evaluate the...

Characteristics of SCC with Fly Ash and Manufactured Sand

NASA Astrophysics Data System (ADS)

Praveen Kumar, K.; Radhakrishna

2016-09-01

Self compacting concrete (SCC) of M40 grade was designed. The binder in SCC consists of OPC and fly ash in the ratio of 65:35. River sand was replaced by manufactured sand (M-sand) at replacement levels of 20,40,60,80 and 100%. An attempt was made to evaluate the workability and strength characteristics of self compacting concrete with river sand and manufactured sand as fine aggregates. For each replacement level, constant workability was maintained by varying the dosage of superplasticizer. T50 flow time, V Funnel time, V-funnel T5 time as well as compressive, split tensile and flexural strength of SCC were found at each replacement level of M-sand. They were compared to SCC with river sand. Results indicate favourable use of M-sand in preparation of Self Compacting Concrete.

Learner-Centered (LCI) vs. Teacher-Centered (TCI) Instruction: A Classroom Management Perspective

ERIC Educational Resources Information Center

Minter, Mary Kennedy

2011-01-01

Teacher education should incorporate management and leadership training with an emphasis on student audience analysis. Macro perspectives of teaching are needed for a workable approach to the management of education.

Portland-cement concrete rheology and workability : final report

DOT National Transportation Integrated Search

2012-12-10

Based on research including four best practice studies, the report proposes a framework for Metropolitan Planning Organizations (MPOs) and partners to use to integrate health into metropolitan area transportation planning. The framework addresses bot...

Management: Curse, Cure-All, or Workable Concept?

ERIC Educational Resources Information Center

Prentice, Marjorie

1973-01-01

In order for curriculum workers to plan and organize in an orderly, rational manner, an operating model is described which identifies the necessary components of the system and clearly states relationships between such components. (Author/CB)

A review of warm mix asphalt.

DOT National Transportation Integrated Search

2008-12-01

Warm Mix Asphalt (WMA) technology, recently developed in Europe, is gaining strong interest in the US. By : lowering the viscosity of asphalt binder and/or increasing the workability of mixture using minimal heat, WMA : technology allows the mixing, ...

Self-Consolidating Concrete for Prestressed Bridge Girders : Research Brief

DOT National Transportation Integrated Search

2017-08-01

Self-consolidating concrete (SCC) is commonly used as an alternative to conventional concrete (CC) in precast, prestressed concrete (PSC) bridge girders. The high strength, highly workable mixture can flow through dense reinforcement to fill formwork...

Hazardous Material Transportation Risks in the Puget Sound Region

DOT National Transportation Integrated Search

1981-09-01

In order to contribute to workable hazardous materials accident prevention and response systems, public safety risks of transporting hazardous materials in the Central Puget Sound Region of Washington State are determined. Risk spectrums are obtained...

Investigation on Hot Workability of Homogenized Al-Zn-Mg-Cu Alloy Based on Activation Energy and Processing Map

NASA Astrophysics Data System (ADS)

Peng, Xiaoyan; Su, Wusen; Xiao, Dan; Xu, Guofu

2018-06-01

Hot deformation behaviors of the homogenized Al-Zn-Mg-Cu alloy were studied by uniaxial compression tests carried out at 623-743 K and strain rates of 0.01-10 s-1. The constitutive equation was developed for the activation energy, and thus the activation energy map was constructed. During the hot deformation, the dominated softening mechanisms were the dynamic recovery and dynamic recrystallization, which were most likely to be driven with increasing temperature and decreasing activation energy. Based on the superposition of the activation energy map and the processing map, together with the microstructure characteristics, the optimized hot workability of the alloy was proposed at the domain (670-743 K and 0.01-0.16 s-1), where the peak efficiency was 0.39 and the activation energy range was 196-260 kJ mol-1.

Relating Fresh Concrete Viscosity Measurements from Different Rheometers

PubMed Central

Ferraris, Chiara F.; Martys, Nicos S.

2003-01-01

Concrete rheological properties need to be properly measured and predicted in order to characterize the workability of fresh concrete, including special concretes such as self-consolidating concrete (SCC). It was shown by a round-robin test held in 2000 [1,2] that different rheometer designs gave different values of viscosity for the same concrete. While empirical correlation between different rheometers was possible, for a procedure that is supposed to “scientifically” improve on the empirical slump tests, this situation is unsatisfactory. To remedy this situation, a new interpretation of the data was developed. In this paper, it is shown that all instruments tested could be directly and quantitatively compared in terms of relative plastic viscosity instead of the plastic viscosity alone. This should eventually allow the measurements from various rheometer designs to be directly calibrated against known standards of plastic viscosity, putting concrete rheometry and concrete workability on a sounder materials science basis. PMID:27413607

Properties of concrete containing ground palm oil fuel ash as fine aggregate replacement

NASA Astrophysics Data System (ADS)

Saffuan, W. A.; Muthusamy, K.; Salleh, N. A. Mohd; Nordin, N.

2017-11-01

Environmental degradation resulting from increasing sand mining activities and disposal of palm oil fuel ash (POFA), a solid waste generated from palm oil mill needs to be resolved. Thus, the present research investigates the effect of ground palm oil fuel ash as partial fine aggregate replacement on workability, compressive and flexural strength of concrete. Five mixtures of concrete containing POFA as partial sand replacement designed with 0%, 10%, 20%, 30% and 40% of POFA by the weight of sand were used in this experimental work. The cube and beam specimens were casted and water cured up to 28 days before subjected to compressive strength and flexural strength testing respectively. Finding shows that concrete workability reduces as the amount of POFA added become larger. It is worth to note that 10% of POFA is the best amount to be used as partial fine aggregate replacement to produce concrete with enhanced strength.

Effects of different crumb rubber sizes on the flowability and compressive strength of hybrid fibre reinforced ECC

NASA Astrophysics Data System (ADS)

Khed, Veerendrakumar C.; Mohammed, Bashar S.; Fadhil Nuruddin, Muhd

2018-04-01

The different sizes of crumb rubber have been used to investigate the effects on flowability and the compressive strength of the hybrid fibre reinforced engineered cementitious composite. Two sizes of crumb rubber 30 mesh and 1 to 3mm were used in partial replacement with the fine aggregate up to 60%. The experimental study was carried out through mathematical and statistical analysis by response surface methodology (RSM) using the Design Expert software. The response models have been developed and the results were validated by analysis of variance (ANOVA). It was found that finer sized crumb rubber inclusion had produced better workability and higher compressive strength when compared to the larger size and it was concluded that crumb rubber has negative effect on compressive strength and positive effect on workability. The optimization results are found to an approximately good agreement with the experimental results.

Promoting employee health by integrating health protection, health promotion, and continuous improvement: a longitudinal quasi-experimental intervention study.

PubMed

von Thiele Schwarz, Ulrica; Augustsson, Hanna; Hasson, Henna; Stenfors-Hayes, Terese

2015-02-01

To test the effects of integrating health protection and health promotion with a continuous improvement system (Kaizen) on proximal employee outcomes (health promotion, integration, and Kaizen) and distal outcomes (workability, productivity, self-rated health and self-rated sickness absence). Twelve units in a county hospital in Sweden were randomized to control or intervention groups using a quasiexperimental study design. All staff (approximately 500) provided self-ratings in questionnaires at baseline, and a 12- and 24-month follow-up (response rate, 79% to 87.5%). There was a significant increase in the proximal outcomes over time in the intervention group compared with the control group, and a trend toward improvement in the distal outcomes workability and productivity. Integration seems to promote staff engagement in health protection and promotion, as well as to improve their understanding of the link between work and health.

High strength nickel-base alloy with improved oxidation resistance up to 2200 degrees F

NASA Technical Reports Server (NTRS)

Freche, J. C.; Waters, W. J.

1968-01-01

Modifying the chemistry of the NASA TAZ-8 alloy and utilizing vacuum melting techniques provides a high strength, workable nickel base superalloy with improved oxidation resistance for use up to 2200 degrees F.

Optimizing cementious content in concrete mixtures for required performance.

DOT National Transportation Integrated Search

2012-01-01

"This research investigated the effects of changing the cementitious content required at a given water-to-cement ratio (w/c) on workability, strength, and durability of a concrete mixture. : An experimental program was conducted in which 64 concrete ...

Criteria for Solid Waste Disposal Facilities: A Guide for Owners/Operators

EPA Pesticide Factsheets

EPA's continuing mission to establish the minimum national standards for landfill design, operation, and management that will enhance landfill safety and boost public confidence in landfills as a component of a workable integrated waste management system.

Evaluation of methods to calculate a wetlands water balance.

DOT National Transportation Integrated Search

2000-08-01

The development of a workable approach to estimating mitigation site water budgets is a high priority for VDOT and the wetlands research and design community in general as they attempt to create successful mitigation sites. Additionally, correct soil...

Muck Utilization in Urban Transportation Tunneling Process

DOT National Transportation Integrated Search

1977-12-01

The purpose of this study is to develop a workable approach to muck utilization for transit tunnels, including cut and cover construction, in the urban area. This report presents the results of a detailed investigation into the potential for muck uti...

Report of concrete pavement evaluation : project 105 C-4181-01 Donahoo Road, Wyandotte County.

DOT National Transportation Integrated Search

2013-12-01

The physical properties of hardened concrete cores and fresh concrete test results were compared with aggregate : gradation workability differences. The concrete cores were taken from a rural two-lane concrete road in northeastern Kansas : constructe...

Planning Faculty Reduction.

ERIC Educational Resources Information Center

Rose, Homer C., Jr.; Hample, Stephen R.

1982-01-01

Considerations that can help colleges and universities develop institutionally specific strategies for planning faculty reductions are addressed. It is suggested that an institution can provide a fair and workable reduction plan if it: thoroughly explores alternatives to faculty layoffs; develops explicit standards and procedures for reduction…

Preparing No-Migration Demonstrations for Municipal Solid Waste Disposal Facilities: A Screening Tool

EPA Pesticide Factsheets

EPA's mission to establish the minimum national standards for landfill design, operation, and management that will enhance landfill safety and boost public confidence in landfills as a component of a workable integrated waste management system.

Optics from Euclid to Huygens.

PubMed

Herzberger, M

1966-09-01

The salient contributions of writers on optics from Euclid to Newton and Huygens are outlined, with a workable bibliography, to encourage present-day workers to restudy the classical writings and to find ideas that lie outside the paths that orthodox optical science has taken.

The Virginia Department of Transportation's statistical specification for hydraulic cement concrete.

DOT National Transportation Integrated Search

1990-01-01

This report reviews some of the principles relating to the application of statistical concepts to be used in the quality assurance and acceptance testing of hydraulic cement concrete. The problems encountered in developing a workable system without a...

Canada

ERIC Educational Resources Information Center

Lawson, Robert F.; Ghosh, Ratna

1986-01-01

Discusses Canada's problems in searching for a national identity and the controversy of the Federal policy of multiculturalism. Presents its objectives within a bilingual framework and the contradictions involved. Suggests a workable model involving assimilation conditioned by regional or local circumstances, useful also as a development strategy.…

Circling through Text: Teaching Research through Multigenre Writing.

ERIC Educational Resources Information Center

Grierson, Sirpa T.

1999-01-01

Describes how the author incorporated her requirements for a term research paper into multigenre writing. Discusses what multigenre is, how it can be taught and assessed, and what makes it such a rich, workable alternative to the traditional research assignment. (SR)

Auditory Localization: An Annotated Bibliography

DTIC Science & Technology

1983-11-01

tranverse plane, natural sound localization in ,-- both horizontal and vertical planes can be performed with nearly the same accuracy as real sound sources...important for unscrambling the competing sounds which so often occur in natural environments. A workable sound sensor has been constructed and empirical

Implementation of a localized roughness specification for use on Louisiana bridges : research project capsule : technology transfer program.

DOT National Transportation Integrated Search

2016-10-01

The Louisiana Transportation Research Center has worked closely with the Bridge : Design section of the Louisiana Department of Transportation and Development : (DOTD) to develop a workable specification for standard and localized roughness : of brid...

Improving U.S. Trade.

ERIC Educational Resources Information Center

Bentsen, Lloyd

1982-01-01

Discusses the need to formulate a coherent trade policy in response to international economic realities. The author argues against a return to trade protectionism and supports efforts to establish workable reciprocity agreements. Increasing import tariffs on high technology products would control access to American markets. (AM)

Annual report of Iowa Highway Research Board research and development activities FY 2010.

DOT National Transportation Integrated Search

2010-12-01

The Highway Division of the Iowa Department of Transportation (Iowa DOT) engages in research and : development for two reasons: first, to find workable solutions to the many problems that require more than : ordinary, routine investigation; and secon...

Being a Teacher of the Behavior Disordered.

ERIC Educational Resources Information Center

Dolce, Russell

1984-01-01

Draws on 13 years experience teaching behavior-disordered students to identify effective teaching methods. Discusses the importance of honesty, fairness, consistency, persistence, intuition, praise, and humor in the teacher-student relationship. Provides eight guidelines for developing a workable and suitable classroom reward system. (JHZ)

A WORKABLE DEFINITION OF SUCCESS

EPA Science Inventory

The most desirable definition of success from the point of view of environmental stewardship is to treat the entire plume to MCLs. Technically, has proven impossible to attain at many sites. A less desirable definition of success is to contain the source of contamination and tr...

Investigation of optimize graded concrete for Oklahoma : phase 1 : final report.

DOT National Transportation Integrated Search

2013-10-01

Optimized Graded Concrete has been a subject widely discussed through the history of concrete. Since aggregates make up over 70% of the volume in a mixture, gradation is critical to the strength, workability, and durability of concrete. In practice o...

Pharmacotherapeutics-Immune Systems: A Required Course that Provides a Framework for Implementing Biotechnology into the Curriculum.

ERIC Educational Resources Information Center

Piascik, Mary M.; Lubawy, William C.

1988-01-01

Inclusion of a course in the pharmacy curriculum that deals primarily with the immune system, its function, malfunction, and therapeutic intervention provides what appears to be a workable focus for discussion of biotechnology. (MSE)

ALLOY FOR USE IN NUCLEAR FISSION

DOEpatents

Spedding, F.A.; Wilhelm, H.A.

1958-03-11

This patent relates to an alloy composition capable of functioning as a solid homogeneous reactor fuel. The alloy consists of a beryllium moderator, together with at least 0.7% of U/sup 235/, and up to 50% thorium to give increased workability to the alloy.

Evaluation of concrete recycling system efficiency for ready-mix concrete plants.

PubMed

Vieira, Luiz de Brito Prado; Figueiredo, Antonio Domingues de

2016-10-01

The volume of waste generated annually in concrete plants is quite large and has important environmental and economic consequences. The use of fresh concrete recyclers is an interesting way for the reuse of aggregates and water in new concrete production. This paper presents a study carried out for over one year by one of the largest ready-mix concrete producers in Brazil. This study focused on the evaluation of two recyclers with distinct material separation systems, herein referred to as drum-type and rotary sieve-type equipment. They were evaluated through characterization and monitoring test programs to verify the behaviour of recovered materials (aggregates, water, and slurry). The applicability of the recovered materials (water and aggregates) was also evaluated in the laboratory and at an industrial scale. The results obtained with the two types of recyclers used were equivalent and showed no significant differences. The only exception was in terms of workability. The drum-type recycler generated fewer cases that required increased pumping pressure. The analysis concluded that the use of untreated slurry is unfeasible because of its intense negative effects on the strength and workability of concrete. The reclaimed water, pre-treated to ensure that its density is less than 1.03g/cm(3), can be used on an industrial scale without causing any harm to the concrete. The use of recovered aggregates consequently induces an increase in water demand and cement consumption to ensure the workability conditions of concrete that is proportional to the concrete strength level. Therefore, the viability of their use is restricted to concretes with characteristic strengths lower than 25MPa. Copyright © 2016 Elsevier Ltd. All rights reserved.

Standard Specification for Language Laboratory.

ERIC Educational Resources Information Center

North Carolina State Dept. of Administration, Raleigh.

This specification covers the components of electronic and electromechanical equipment, nonelectronic materials for the teacher-student positions, and other items of a miscellaneous nature to provide for a complete and workable language laboratory facility. Language laboratory facilities covered by this specification are of two types: (1)…

Standard Specifications for Language Laboratory.

ERIC Educational Resources Information Center

North Carolina State Dept. of Administration, Raleigh.

Specifications are presented covering the components of electronic and electro-mechanical equipment, non-electrical materials for the teacher-student positions, and other items of a miscellaneous nature to provide for a complete, workable language laboratory facility. Instructions for the use of specifications are included for the purchaser,…

Vocational Preparation Curriculum: Welding.

ERIC Educational Resources Information Center

Usoro, Hogan

Designed to be a workable guide for instructors serving the occupational needs of various categories of disadvantaged and handicapped students, this welding curriculum contains fourteen units of self-paced and self-contained instructional materials. The instructional units cover the following topics: job opportunities in welding, safety rules in…

Chemical modification of uniform soils and soils with high/low plasticity index.

DOT National Transportation Integrated Search

2016-08-01

The addition of chemicals into the subgrade has been widely used during construction to improve the soil properties. The chemicals, often Lime Kiln Dust (LKD) and Portland cement, are added to the soil to improve its workability, compactability and e...

Classroom Management in the Elementary Grades. Research Series No. 32.

ERIC Educational Resources Information Center

Brophy, Jere E.; Putnam, Joyce G.

The literature on elementary school classroom management is reviewed. Topics include student characteristics and individual differences, preparing the classroom as a learning environment, organizing instruction and support activities to maximize student engagement in productive tasks, developing workable housekeeping procedures and conduct rules,…

32 CFR 562.5 - Policies.

Code of Federal Regulations, 2010 CFR

2010-07-01

... workable program. The right of orderly campus dissent is recognized. However, anti-ROTC activities which... accomplish program objectives of the host institution. Activities which are part of the host school's... that each cadet realizes the importance of choice of branch preferences and what is involved in making...

Report of concrete pavement evaluation : project 105 C-4181-01 Donahoo Road, Wyandotte County : [technical summary].

DOT National Transportation Integrated Search

2013-12-01

The physical properties of hardened concrete cores and fresh concrete test results were compared with aggregate gradation workability differences. The concrete cores were taken from a rural two-lane concrete road in northeastern Kansas constructed in...

Final report : sampling plan for pavement condition ratings of secondary roads.

DOT National Transportation Integrated Search

1984-01-01

The purpose of this project was to develop a random sampling plan for use in selecting segments of the secondary highway system for evaluation under the Department's PMS. The plan developed is described here. It is a simple, workable, random sampling...

An adaptive bit synchronization algorithm under time-varying environment.

NASA Technical Reports Server (NTRS)

Chow, L. R.; Owen, H. A., Jr.; Wang, P. P.

1973-01-01

This paper presents an adaptive estimation algorithm for bit synchronization, assuming that the parameters of the incoming data process are time-varying. Experiment results have proved that this synchronizer is workable either judged by the amount of data required or the speed of convergence.

MSIAC’s M&S Journal Online: Volume 2, September 2006

DTIC Science & Technology

2006-09-01

engineering fields, such as mechanical and electrical , rely on composability and interchangeability (substitutability) of components into workable systems...Terrain Data for the Vector-in-Command and Engineer Functional Area Models”, Technical Report GL-90-9, September 1990, USAEWES, Vicksburg 8. Frankenstein

Every Child. Volume 13, Number 2, 2007

ERIC Educational Resources Information Center

Elliott, Alison, Ed.

2007-01-01

The theme of this issue of "Every Child" is "Challenging Practice and Challenging Practices." It covers a range of issues challenging the images of a "traditional" children's service. Contents include an editorial by Alison Elliott, "Wise Vision, Workable Solutions and Early Childhood Action," a guest…

TECHNIQUES FOR EFFECTIVE TEACHING.

ERIC Educational Resources Information Center

HASTINGS, GERALDINE; AND OTHERS

A COMPENDIUM OF WORKABLE AND REASONABLE TECHNIQUES TO PROVIDE TEACHERS WITH ALTERNATIVES IN SELECTING LEARNING EXPERIENCES IS PRESENTED. MATERIALS ARE DESIGNED TO AID TEACHERS AND LEARNERS IN ALL SUBJECT MATTER AREAS. TEACHING TECHNIQUES DESCRIBED ARE (1) THE CASE STUDY, (2) DISCUSSIONS SUCH AS SYMPOSIUM, COLLOQUIUM, BUZZ SESSIONS, AND…

Policy-Making in a Negotiating Society

ERIC Educational Resources Information Center

Carey, William D.

1976-01-01

A national disenchantment with knowledge, which sets up a contest between reason and mindlessness, and a strong tilt in the direction of conservative fiscal policy are cited as cause for those seeking support for science to take the initiative and negotiate a workable policy future. (JT)

Criteria Underlying the Formation of Alternative IMS Configurations.

ERIC Educational Resources Information Center

Dave, Ashok

To assist the formation of IMS (Instructional Management System) configurations, three categories of characteristics are developed and explained. Categories 1 and 2 emphasize automation, and the necessity of forming workable configurations to carry out instructional management for Southwest Regional Laboratory developed instructional and/or…

Conditioned Demand and Professional Response.

ERIC Educational Resources Information Center

Rhoades, Gary

1984-01-01

Two basic features of British higher education administration bearing on the workability of recent Leverhulme study proposals for the future of British higher education are examined. Vertical integration, (the relationship of secondary and higher education systems) and a high degree of professionalism enhancing it will influence reforms…

Cost-Effective Uses of Lightweight Aggregate Made from Dredged Material in Construction

DOT National Transportation Integrated Search

2018-01-31

Lightweight aggregate (LWA) can be used in concrete to reduce its self-weight and improve its workability and durability. It could potentially be used as borrow for embankment construction, which is expected to reduce the stresses on the subgrade fou...

23 CFR 669.5 - Objective.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Objective. 669.5 Section 669.5 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS ENFORCEMENT OF HEAVY VEHICLE USE TAX § 669.5 Objective. The objective of this regulation is to establish realistic and workable...

A Workable In-Depth Curriculum Evaluation Plan.

ERIC Educational Resources Information Center

Wakim, Judith H.

1983-01-01

Describes the six-year evolution of a comprehensive evaluation plan used to enhance a nursing program. Includes the plan with specific questions, deadlines, and documentation procedures. The plan provides a rational basis for improvements, orients newcomers, and lets everyone know what their evaluation responsibilities are. (JOW)

Oxidation behaviour of silicon-free tungsten alloys for use as the first wall material

NASA Astrophysics Data System (ADS)

Koch, F.; Brinkmann, J.; Lindig, S.; Mishra, T. P.; Linsmeier, Ch

2011-12-01

The use of self-passivating tungsten alloys as armour material of the first wall of a fusion power reactor may be advantageous concerning safety issues. In earlier studies good performance of the system W-Cr-Si was demonstrated. Thin films of such alloys showed a strongly reduced oxidation rate compared to pure tungsten. However, the formation of brittle tungsten silicides may be disadvantageous for the powder metallurgical production of bulk W-Cr-Si alloys if a good workability is needed. This paper shows the results of screening tests to identify suitable silicon-free alloys with distinguished self-passivation and a potentially good workability. Of all the tested systems W-Cr-Ti alloys showed the most promising results. The oxidation rate was even lower than the one of W-Cr-Si alloys, the reduction factor was about four orders of magnitude compared to pure tungsten. This performance could be conserved even if the content of alloying elements was reduced.

Compressive strength performance of OPS lightweight aggregate concrete containing coal bottom ash as partial fine aggregate replacement

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Mohamad Hafizuddin, R.; Mat Yahaya, F.; Sulaiman, M. A.; Syed Mohsin, S. M.; Tukimat, N. N.; Omar, R.; Chin, S. C.

2018-04-01

Concerns regarding the negative impact towards environment due to the increasing use of natural sand in construction industry and dumping of industrial solid wastes namely coal bottom ash (CBA) and oil palm shell (OPS) has resulted in the development of environmental friendly lightweight concrete. The present study investigates the effect of coal bottom ash as partial fine aggregate replacement towards workability and compressive strength of oil palm shell lightweight aggregate concrete (OPS LWAC). The fresh and mechanical properties of this concrete containing various percentage of coal bottom ash as partial fine aggregate replacement were investigated. The result was compared to OPS LWAC with 100 % sand as a control specimen. The concrete workability investigated by conducting slump test. All specimens were cast in form of cubes and water cured until the testing age. The compressive strength test was carried out at 7 and 28 days. The finding shows that integration of coal bottom ash at suitable proportion enhances the strength of oil palm shell lightweight aggregate concrete.

Rheological and Mechanical Response Modifications for a Self-Leveling Mortar

NASA Astrophysics Data System (ADS)

Katsiadramis, N. J.; Sotiropoulou, A. B.; Pandermarakis, Z. G.

2010-06-01

In many cases cement based materials demand a higher flowability and workability and this conventionally can’t be done without loss of its strength, due to the fact that the common practice to increase the workability is the addition of water. But, nowadays using a third generation superplasticizer (SP) we can achieve the desire flowability without loss of its strength. The action of superplastisizers is to spread efficiently the cement grains and so to wetting better the cement grains giving a more homogeneous mixture with higher strength. Nine different mixtures were prepared adding a small percentage of SP (1%). The conditions to get a self levelling mortar, have to do not only with rheological but also with mechanical demands. The bending and compression test gave the achieving mechanical strength whereas their rheological response came through slump flow and v-funnel flow tests. With the help of a small amount of stabilizer we obtain a robust mixture that deserves the desire response at the field too.

Performance of steel wool fiber reinforced geopolymer concrete

NASA Astrophysics Data System (ADS)

Faris, Meor Ahmad; Abdullah, Mohd Mustafa Al Bakri; Ismail, Khairul Nizar; Muniandy, Ratnasamy; Ariffin, Nurliayana

2017-09-01

In this paper, performance of geopolymer concrete was studied by mixing of Class F fly ash from Manjung power station, Lumut, Perak, Malaysia with alkaline activator which are combination of sodium hydroxide and sodium silicate. Steel wool fiber were added into the geopolymer concrete as reinforcement with different weight percentage vary from 0 % - 5 %. Chemical compositions of Malaysian fly ash was first analyzed by using X-ray fluorescence. All geopolymer concrete reinforced with steel wool fiber with different weight percentage were tested in terms of density, workability, and compression. Result shows Malaysian fly ash identified by using XRF was class F. Density of geopolymer concrete close to density of OPC which is approximately 2400 kg/m3 and the density was increase gradually with the additions of steel fiber. However, the inclusions of steel fibers also shows some reduction to the workability of geopolymer concrete. Besides, the compressive strength was increased with the increasing of fibers addition until maximum of 18.6 % improvement at 3 % of steel fibers.

Slicing of Silicon into Sheet Material: Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1979-01-01

Testing of low cost low suspension power slurry vehicles is presented. Cutting oils are unlikely to work, but a mineral oil with additives should be workable. Two different abrasives were tested. A cheaper silicon carbide from Norton gave excellent results except for excessive kerf loss: the particles were too big. An abrasive treated for lubricity showed no lubricity improvement in mineral oil vehicle. The bounce fixture was tested for the first time under constant cut rate conditions (rather than constant force). Although the cut was not completed before the blades broke, the blade lifetime of thin (100 micrometer) blades was 120 times the lifetime without the fixture. The large prototype saw completed a successful run, producing 90% cutting yield (849 wafers) at 20 wafers/cm. Although inexperience with large numbers of wafers caused cleaning breakage to reduce this yield to 74%, the yield was high enough that the concept of the large saw is proven workable.

Effects of aggregate grading on the properties of steel fibre-reinforced concrete

NASA Astrophysics Data System (ADS)

Acikgens Ulas, M.; Alyamac, K. E.; Ulucan, Z. C.

2017-09-01

This study investigates the effects of changing the aggregate grading and maximum aggregate size (D max ) on the workability and mechanical properties of steel fibre-reinforced concrete (SFRC). Four different gradations and two different D max were used to produce SFRC mixtures with constant cement dosages and water/cement ratios. Twelve different concrete series were tested. To observe the properties of fresh concrete, slump and Ve-Be tests were performed immediately after the mixing process to investigate the effects of time on workability. The hardened properties, such as the compressive, splitting tensile and flexural strengths, were also evaluated. In addition, the toughness of the SFRC was calculated. Based on our test results, we can conclude that the grading of the aggregate and the D max have remarkable effects on the properties of fresh and hardened SFRC. In addition, the toughness of the SFRC was influenced by changing the grading of the aggregate and the D max .

An Analysis of the Alteration Specialist Occupation.

ERIC Educational Resources Information Center

Buerkel, Elaine; Rehling, Joseph H.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the textile service occupation. The industry needs properly trained alteration specialists, bushelmen and dressmakers, in the repairing, remodeling, altering or renovating of garments. Their personal…

Student Housing. A Report.

ERIC Educational Resources Information Center

Tolmach, Judy

This publication describes economical ways to provide better housing for students and provides examples of workable solutions to the problem at various colleges and universities. For more economical and better housing, the author recommends (1) humanizing existing dormitories by changing the standard double rooms into suites of bedrooms with a…

Checklist for Change.

ERIC Educational Resources Information Center

Sills, Angelyn C.

1995-01-01

Describes a straightforward, workable strategy that involves a teacher checklist and short individual or student group conferences, with the goal of academic or behavioral improvements. Teachers can easily tick off marks on the checklist and return the form to the counselor; additionally, students can easily understand the format of the checklist.…

A Cognitive Perspective in the Treatment of Incarcerated Clients.

ERIC Educational Resources Information Center

Walsh, Thomas C.

1990-01-01

Proposes a cognitive therapy model as a workable approach in treating incarcerated clients. Reviews principal components and techniques of cognitive theory. Uses case vignettes to illustrate application of this approach. Delineates key features of cognitive model which relate to treatment of incarcerated population. (Author/ABL)

Yes, the GIGP Really Does Work--And Is Workable!

ERIC Educational Resources Information Center

Burrell, Quentin L.; Fenton, Michael R.

1993-01-01

Discusses the generalized inverse Gaussian-Poisson (GIGP) process for informetric modeling. Negative binomial distribution is discussed, construction of the GIGP process is explained, zero-truncated GIGP is considered, and applications of the process with journals, library circulation statistics, and database index terms are described. (50…

Small Can Be Beautiful.

ERIC Educational Resources Information Center

Van Patten, Betsy

1984-01-01

Grant proposals are most likely to succeed when they are based on solid, well-conceived ideas. Long-range planning is the best way to come up with workable ideas that will convince small foundations of a project's merits. Planning helps identify an institution's top priorities and achieve a consensus. (MLW)

Repeated Prescribed Burning in Aspen

Treesearch

Donald A. Perala

1974-01-01

Infrequent burning weather, low flammability of the aspen-hardwood association, and prolific sprouting and seeding of shrubs and hardwoods made repeated dormant season burning a poor tool to convert good site aspen to conifers. Repeat fall burns for wildlife habitat maintenance is workable if species composition changes are not important.

Student Credit Card Debt in the 21st Century: Options for Financial Aid Administrators.

ERIC Educational Resources Information Center

Oleson, Mark

2001-01-01

Provides multiple workable solutions financial aid offices can offer students throughout their college experience to deal with debt: preventive solutions for avoiding problems with credit card debt, holistic solutions for other related problems, and remedial solutions for existing problems. (EV)

National Defense on the High Frontier.

ERIC Educational Resources Information Center

Graham, Daniel O.

1983-01-01

A new American defense policy based on satellites which can track down and destroy Soviet missiles is less expensive and more workable than is commonly believed. Such a policy would provide a greater margin of safety than the present policy of deterence based on mutually assured destruction. (IS)

QUANTITATIVE DECISION TOOLS AND MANAGEMENT DEVELOPMENT PROGRAMS.

ERIC Educational Resources Information Center

BYARS, LLOYD L.; NUNN, GEOFFREY E.

THIS ARTICLE OUTLINED THE CURRENT STATUS OF QUANTITATIVE METHODS AND OPERATIONS RESEARCH (OR), SKETCHED THE STRENGTHS OF TRAINING EFFORTS AND ISOLATED WEAKNESSES, AND FORMULATED WORKABLE CRITERIA FOR EVALUATING SUCCESS OF OPERATIONS RESEARCH TRAINING PROGRAMS. A SURVEY OF 105 COMPANIES REVEALED THAT PERT, INVENTORY CONTROL THEORY AND LINEAR…

Action Research and Narrative Inquiry: Five Principles for Validation Revisited

ERIC Educational Resources Information Center

Heikkinen, Hannu L. T.; Huttunen, Rauno; Syrjala, Leena; Pesonen, Jyri

2012-01-01

The article continues the discussion of the five quality principles proposed by Heikkinen, Huttunen, and Syrjala, published in 2007 in "Educational Action Research". In the present article, the authors reconsider the five principles: historical continuity; reflexivity; dialectics; workability; and evocativeness. These five principles are…

An Extension Case Study in Institutional Innovation: Microfinance Intermediary Formation

ERIC Educational Resources Information Center

Edelman, Mark A.

2015-01-01

An institutional innovation process led by Extension created a statewide microfinance intermediary. The intermediary provides business technical assistance and microloans to entrepreneurs having difficulty securing conventional credit but having workable business plans. The process included (1) gathering indicators of a problem; (2) formation of a…

Censorship: Managing the Controversy.

ERIC Educational Resources Information Center

National School Boards Association, Alexandria, VA.

In this monograph, certain viewpoints, strategies, and policy tips have been separated from the main text. These "notebooks" of information, taken together, comprise a useful handbook for school officials who want to recognize censorship, put it in perspective, and prepare for consequent controversy. The purpose is to provide workable strategies…

An Analysis of the Landscaping Occupation.

ERIC Educational Resources Information Center

Stemple, Lynn L.; Dilley, John E.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the landscape services occupation. Depending on the preparation and abilities of the individual student, he may enter the landscape area as (1) nursery worker, (2) landscape planter, (3) landscape…

Business Services' Impact on Student Retention: Exploring Student and Administrator Perceptions

ERIC Educational Resources Information Center

Hassabis, Haris

2014-01-01

High student attrition rates for first-year university students affect the financial and long-term sustainability of institutions. Previous researchers failed to provide workable solutions to improving student retention. This study was an exploration of students' and administrators' perceptions of business services and their potential impact on…

Plans, Programs, Strategies for the Future in the Education of Black Elementary and Secondary School Children

ERIC Educational Resources Information Center

Robinson, Andrew A.

1976-01-01

Describes four distinct periods in the history of black education in this country prefacing his description by the assertion that America's genius is its ability to weld together a nation of different peoples into a workable, if not efficient, social order. (Author/AM)

A Peanuty Dilemma

ERIC Educational Resources Information Center

Hoff, Dianne L.; Mitchell, Sidney N.

2010-01-01

Designing school accommodations for students with potentially life-threatening peanut allergies is a daunting challenge for schools. Parents of children with peanut allergies put a lot of pressure on schools to make them peanut-free, even though medical and legal experts say that is not a sound, or even workable, solution. One solution is to…

Improving Bilingual Program Management. A Handbook for Title VII Directors.

ERIC Educational Resources Information Center

DeGeorge, George P., Ed.

Filled with practical advice and workable techniques and strategies to help bilingual program directors deal with the problems they face, this handbook brings together ideas and suggestions from Title VII program directors, state coordinators, and superintendents with experience in bilingual programs. The handbook, written in question and answer…

Cyber Bullying and Academic Performance

ERIC Educational Resources Information Center

Faryadi, Qais

2011-01-01

This research investigates the emotional and physiological effects of cyber bullying on the university students. The primary objective of this investigation is to identify the victims of cyber bullying and critically analyze their emotional state and frame of mind in order to provide them with a workable and feasible intervention in fighting cyber…

Portfolios in Practice: What Is a Portfolio?

ERIC Educational Resources Information Center

Arter, Judith A.

A consortium effort sponsored by the Northwest Regional Evaluation Association has arrived at a workable definition of a portfolio that takes into account the viewpoints of teachers and those interested in large-scale assessment. The modified definition states that: "A student portfolio is a purposeful collection of student work that tells…

Can Your District Survive a Data Disaster?

ERIC Educational Resources Information Center

Smith, Gary

2011-01-01

School business administrators have long recognized the need for a workable data recovery plan regardless of cause. Yet many have not reassessed their current data backup and recovery capabilities, perhaps because they have not experienced a catastrophic failure. There are three reasons school business administrators may not realize or recognize…

Personality Types as an Indicator of Online Student Success and Retention

ERIC Educational Resources Information Center

Meredith, Ben P.

2011-01-01

With online education courses within public institutions realizing lower than average retention and success rates for students, current retention practices and models are falling woefully short of providing workable, viable answers to keeping students and helping them be successful without lowering academic standards. While a relationship between…

An Analysis of the Baking Occupation.

ERIC Educational Resources Information Center

Boyadjid, Thomas A; Paoletti, Donald J.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the baking occupation. Such tasks as choosing ingredients and the actual baking process are logical primary concerns, but also explored are the safety and sanitation factors and management problems in a…

New class of thermosetting plastics has improved strength, thermal and chemical stability

NASA Technical Reports Server (NTRS)

Burns, E. A.; Dubrow, B.; Lubowitz, H. R.

1967-01-01

New class of thermosetting plastics has high hydrocarbon content, high stiffness, thermal stability, humidity resistance, and workability in the precured state. It is designated cyclized polydiene urethane, and is applicable as matrices to prepare chemically stable ablative materials for rocket nose cones of nozzles.

Gardening for All: The Accessible Garden. Revised Edition.

ERIC Educational Resources Information Center

Brock, Holly; Mefford, Gayle

1990-01-01

This pamphlet presents some innovative thoughts and suggestions to make gardening an "accessible" activity for any gardener, able-bodied or disabled. For gardeners with special needs, workability of the garden must take precedence over a conventional garden design. Designs to consider include raised bed gardens, garden containers such as whiskey…

Copyright: A Guide for Public Humanities Projects. Federation Resources 3.

ERIC Educational Resources Information Center

Rozeen, Mark

As public humanities programs increasingly make use of media products, an understanding of copyrights is essential. Some problems pertaining to copyrights may be alleviated by advanced planning, a clear division of responsibilities, and by using reason to determine that policies are workable and fair. The problem involves a growing…

Appraisal and Evaluation: Chimera, Fantasy, or Practicality?

ERIC Educational Resources Information Center

Marland, Michael

1986-01-01

Looks beyond the threatening and remunerative aspects of teacher appraisal in the United Kingdom to the contribution that evaluation can make to professional and school development. Considers five sound reasons for appraisal, the roles and behaviors to be appraised, and some workable approaches and techniques. Effective leadership is the key.…

An Analysis of the Auto Mechanic Occupation.

ERIC Educational Resources Information Center

Conner, Michael; Thoman, LeRoy

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the auto mechanic occupation. It identifies the broad area of skills and knowledge necessary to perform various tasks involved in diagnosis, maintenance, and repair of automotive systems. Selected…

Planning the Library Media Center Facility for the 1990s and Beyond.

ERIC Educational Resources Information Center

Texas Education Agency, Austin.

This manual presents recommendations for incorporating present and future technological changes into workable, efficient, pleasant school library media facilities in two major sections: Planning the Facility and Activity Areas. The first section addresses the planning process (appointing the building committee, evaluating the library media…

New Student Orientation.

ERIC Educational Resources Information Center

Florida A and M Univ., Tallahassee.

At the beginning of the l974-75 term, Florida A & M University innovated the concept of the miniquarter. Its central purpose was to foster the development of the collegiate life styles, attitudes, motivations, and work-study habits almost absolutely demanded by competitive curricula. The idea appeared to be rational, relevant, and workable.…

Classroom Dialogues: Connections amid Incongruities (New Teachers Workshop).

ERIC Educational Resources Information Center

Kroll, Catherine W.

1990-01-01

Describes the workable strategies a student teacher found to deal with student apathy and disinterest. Discusses the use of script writing; balancing "old" literature with writing hot off the presses; using writing about real subjects which captivate student interest to work on writing arguments; and exploring cultural incongruities through…

78 FR 75483 - Federal Travel Regulation (FTR); Relocation Allowances; Commuted Rate

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-12

... Allowances; Commuted Rate AGENCY: Office of Governmentwide Policy (OGP), U.S. General Services Administration (GSA). ACTION: Final rule. SUMMARY: The GSA, OGP, is providing a workable commuted rate to be used by.... 5724(c) requires that GSA maintain a commuted rate incorporating all aspects of household goods...

Dan Says - Continuum Magazine | NREL

Science.gov Websites

good science will reward you with unexpected insights - some more profound than you ever could have insights we gain through the basic science we perform is essential to our applied technology R&D, and answer the fundamental questions of science. Their colleagues forge those new insights into workable

PROCESS OF PRODUCING ACTINIDE METALS

DOEpatents

Magel, T.T.

1959-07-14

The preparation of actinide metals in workable, coherent form is described. In general, the objects of the invention are achieved by heating a mixture of an oxide and a halide of an actinide metal such as uranium with an alkali metal on alkaline earth metal reducing agent in the presence of iodine.

Analyzing Prosocial Content on T.V.

ERIC Educational Resources Information Center

Davidson, Emily S.; Neale, John M.

To enhance knowledge of television content, a prosocial code was developed by watching a large number of potentially prosocial television programs and making notes on all the positive acts. The behaviors were classified into a workable number of categories. The prosocial code is largely verbal and contains seven categories which fall into two…

An Analysis of the Automobile Sales Occupation.

ERIC Educational Resources Information Center

Bohac, Robert D.; Vernon, Robert C.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the auto sales occupation. The analysis follows the salesperson through the essential everyday performance of the tasks in the occupation. The duties involve the process of obtaining the prospects and…

Transfer and development length of prestressing tendons in full-scale AASHTO prestressed concrete girders using self-consolidating concrete.

DOT National Transportation Integrated Search

2009-03-01

Self-consolidating concrete (SCC) is a highly workable concrete that flows through densely reinforced or : complex structural elements under its own weight. The benefits of using SCC include: a) Reducing labor costs : by eliminating the need for mech...

How to Build Public Relationships That Motivate Real Support.

ERIC Educational Resources Information Center

Jackson, Patrick

1986-01-01

Public relations is a process that should produce relationships (not merely favorable public opinion) and should target a few opinion leaders and others who really care about individual schools. As chief public relations officers, principals need to understand the information diffusion process and use workable tactics to produce solid community…

Elusive '68: The Challenge to Pedagogy

ERIC Educational Resources Information Center

Donahue, William Collins

2008-01-01

Teaching '68 presents pedagogical challenges far greater than assembling a set of workable classroom materials. Divisive controversies that were the hallmark of the time--e.g., the debate over the nature and appropriate use of violence--are with us still, though in a somewhat different form. Further, the instructor's own politics and positionality…

An Analysis of the Horticulture Equipment and Services Occupation.

ERIC Educational Resources Information Center

Harbage, Monroe; Lechner, Donald L.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the horticulture equipment and services occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Fourteen duties are…

Implementing the Regular Education Initiative in Secondary Schools: A Different Ball Game.

ERIC Educational Resources Information Center

Schumaker, Jean B.; Deshler, Donald D.

1988-01-01

The article reviews potential barriers to implementing the Regular Education Initiative (REI) in secondary schools and then discusses a set of factors central to developing a workable partnership, one that is compatible with the goals of the REI but that also responds to the unique parameters of secondary schools. (Author/DB)

Eliminating Standardized Tests in College Admissions: The New Affirmative Action?

ERIC Educational Resources Information Center

Zwick, Rebecca

1999-01-01

Eliminating the Scholastic Aptitude Test for college admissions might seem a form of covert affirmative action. Although it is possible to design a workable admissions policy that excludes standardized tests (as 15 percent of colleges have done), banishing admissions tests to further a social-policy goal indirectly is unsound policy. (Contains 25…

An Effective Approach to Drug Education.

ERIC Educational Resources Information Center

Frank, Peter R.

Traditionally, drug abuse education in the public schools has been approached through the use of scare tactics and scientific data. This document suggests that the old methods are not workable, and therefore attention should be directed toward helping the child develop a good self-concept and teaching decision-making skills. In the You and Your…

The Interactive Effects of Rules on Teaching Timetable Flexibility and Resource Utilization.

ERIC Educational Resources Information Center

Wesson, David A.

1995-01-01

Effect of administrative rules concerning scheduling on college faculty's productivity is examined. Three potential effects are that rules interact with other rules to produce rigidity; scheduling changes cause greater disruption as rules and rigidity increase; and at some point, rules prohibit creation of a workable schedule for teaching facility…

Pay-for-Knowledge Compensation Plans: Hypotheses and Survey Results.

ERIC Educational Resources Information Center

Gupta, Nina; And Others

1987-01-01

The authors describe the concept of "pay-for-knowledge" compensation plans and report results from a survey of 20 personnel directors in pay-for-knowledge plants. Results indicate that companies using this system have generally found it workable and feel it would be a mistake to revert to traditional compensation plans. (CH)

Building International Relations for Children through Sister Schools.

ERIC Educational Resources Information Center

Pryor, Carolyn B.

1992-01-01

Inspired by Sister Cities International and the NASSP's school-to-school exchange program, "sister school" pairings have proved to be workable educational programs with long-range impact on participants. Some post-cold war efforts include U.S.-USSR High School Academic Partnerships, Project Harmony, and Center for U.S.-USSR Initiatives.…

Tractor Hydraulics. A Teaching Reference.

ERIC Educational Resources Information Center

American Association for Vocational Instructional Materials, Athens, GA.

The manual was developed to help provide a better understanding of how and why hydraulic principles serve the purposes of weight reduction, increase of physical effort, and more precise control to machines of all types. The four components that are necessary to have a workable hydraulic system--a reservoir, a pump, a valve, and a motor (cylinder)…

SECOND-ORDER PROBLEMS IN STUDIES OF PERCEPTUAL DEVELOPMENT.

ERIC Educational Resources Information Center

WHITE, BURTON L.

RECENT RESEARCH FINDINGS ON THE PERCEPTUAL DEVELOPMENT OF YOUNG INFANTS WERE SURVEYED, AND THE NEED FOR SYNTHESIZING THESE NEW FINDINGS INTO WORKABLE CONCEPTS WAS SUGGESTED FOR THE FRUITFUL STUDY OF HIGHER ORDER CONSIDERATIONS IN THE FUTURE. A DISCUSSION WAS MADE ON THE DEVELOPMENTAL ISSUES OF--(1) SUPERORDINATE CATEGORIES OF PERCEPTUAL FUNCTION,…

An Analysis of the Billing and Bookkeeping Machine Operator Occupation.

ERIC Educational Resources Information Center

Six, Joseph E., Jr.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the billing and bookkeeping machine operating occupation. The analysis was written in general terms due to the diversity in bookkeeping machines on the market, increasing number and variation of the tasks…

Renewable energy and wildlife conservation

USGS Publications Warehouse

Khalil, Mona

2016-09-09

The renewable energy sector is rapidly expanding and diversifying the power supply of the country. Yet, as our Nation works to advance renewable energy and to conserve wildlife, some conflicts arise. To address these challenges, the U.S. Geological Survey (USGS) is conducting innovative research and developing workable solutions to reduce impacts of renewable energy production on wildlife.

A Love towards a Thing Eternal: Spinoza and the Classroom

ERIC Educational Resources Information Center

Shann, Steve; Bauer, Michele; Cunneen, Rachel; Troy, Jaki; Van Blerk, Courtney

2015-01-01

There is a growing concern about the struggles of early career teachers and an understandable questioning of the preparation being offered by teacher education courses. Are our preservice teachers being given workable strategies and techniques to allow them to survive the early years? Is it strategies and techniques that are primarily at issue…

An Analysis of the Commercial Art Occupation.

ERIC Educational Resources Information Center

Mowen, Kenneth A.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the commercial artist occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Seventeen duties are broken down into a…

Inferior Blueberries and Other Excuses I've Heard

ERIC Educational Resources Information Center

Van Winkle, David

2005-01-01

In this article, the author relates the blueberry story, as one of many excuses for barely advancing the status quo, and suggests a workable framework that is common to both education and business. Unfortunately, many business and education leaders seem intent on fixing specific issues and fail to acquire a systemic perspective. These isolated…

Health Education Teaching Ideas: Secondary. Revised Edition.

ERIC Educational Resources Information Center

Loya, Richard, Ed.; Bensley, Loren B., Jr., Ed.

Part I of this teaching guide contains teaching strategies which originally appeared in the "Journal of Health Education" (JHE) and were included in the first edition of this guide, published in 1983. Part II includes teaching strategies published in JHE since 1983. The guide is designed to be a reference for those seeking workable ideas in…

An Analysis of the Machine Trades Occupation.

ERIC Educational Resources Information Center

Hall, Charles W.; Emory, Harold L.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the machine trades occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Fifteen duties are broken down into a number…

Designing a Workable Framework for Evaluating Distance Language Instruction

ERIC Educational Resources Information Center

Madyarov, Irshat

2009-01-01

Teaching foreign languages at distance is now becoming widespread; so is the need for evaluating online language courses. This article discusses an example of a framework that was applied to evaluate an online English as a foreign language (EFL) course at a Middle Eastern university. The development of the framework investigated areas of interest…

Global Interdependence Education: A Key Resource for the Transformation of Civilization.

ERIC Educational Resources Information Center

Siegmund, Mark

1983-01-01

We must acquire the fullest understanding and use of our life support system and begin a movement of energies away from scarcity and toward self-sufficiency. Global interdependence education can assist in this process. Educators will be called on to demonstrate the workability and necessity of whole-system approaches. (SR)

An Analysis of the Laboratory Assisting Occupation.

ERIC Educational Resources Information Center

McGee, Patricia; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the laboratory assistant occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eleven duties are broken down into a…

48 CFR 1552.215-72 - Instructions for the Preparation of Proposals.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., “Payments Under Time and Materials and Labor-Hour Contracts,” include in the cost proposal the estimated... to reflect the Government's estimate of the offeror's probable costs. Any inconsistency, whether real... hours are the workable hours required by the Government and do not include release time (i.e., holidays...

An Evolving Approach to Learning Problem Solving and Program Development: The Distributed Learning Model

ERIC Educational Resources Information Center

Deek, Fadi; Espinosa, Idania

2005-01-01

Traditionally, novice programmers have had difficulties in three distinct areas: breaking down a given problem, designing a workable solution, and debugging the resulting program. Many programming environments, software applications, and teaching tools have been developed to address the difficulties faced by these novices. Along with advancements…

Taking School Reform Success to "Scale": Governance and Leadership Issues in Two Restructuring Elementary Buildings.

ERIC Educational Resources Information Center

Goldman, Paul; Tindal, Gerald

This paper explores the difficulties of extending good, workable educational ideas to entire schools or districts. Two restructured schools that participated in a 4-year collaborative project that involved multi-age primary classrooms, inclusion of special-needs students in regular classrooms, and increasing specificity in assessing student…

Innovations in Continuing Education. 1979 Award-Winning New Programs. NUEA-ACT Series on Continuing Education. No. 5.

ERIC Educational Resources Information Center

National Univ. Extension Association, Washington, DC.

Seven 1979 innovative programs in continuing education are described which won awards from the American College Testing Program and the National University Extension Association. Awards were granted according to programs' transferability, innovativeness, workability, and impact in one of four categories: instructional programs, student services…

Chapter Innovators Guide, 2000: Models of Innovation Award Winners.

ERIC Educational Resources Information Center

National FFA Organization, Indianapolis, IN.

This guide presents the Future Farmers of America (FFA) 2000 Model of Innovation award winners' projects. Chapters demonstrated abilities to identify goals and objectives, create a workable plan of action, attain and evaluate results, and identify items learned and ways to improve. Chapter 1 discusses the FFA National Chapter Award program that…

Evaluating the Impact of Instructional Multimedia: Workable Techniques.

ERIC Educational Resources Information Center

Rathbun, Gail A.; Goodrum, David A.

A framework is proposed for the formative evaluation of multimedia. It describes techniques that have worked well in the evaluation of software development and gives examples of the use of evaluation results. The focus is primarily on the degree to which the instructional multimedia program supports the user's activities and tasks in the user's…

On the road: workable solutions to the problems of roads and highways

Treesearch

Mary M. Rowland

2004-01-01

Fourteen authors, ranging from transportation specialists to ecologists, have collaborated to write this very useful compendium describing the newly minted discipline of "road ecology." The authors state that road ecology "uses the science of ecology and landscape ecology to explore, understand, and address the interactions of roads and vehicles with...

An Analysis of the Insurance Sales Occupation.

ERIC Educational Resources Information Center

Moore, Gordon; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the insurance sales occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eleven duties are broken down into a number…

Student-Scientist Partnership in Molecular Biology: Finding a Workable Model at an Undergraduate Institution

ERIC Educational Resources Information Center

Clendening, Beverly

2004-01-01

Two molecular genetic projects were undertaken in Drosophila Molecular Genetics in partnership with teachers from High Schools. The students gained experience with DNA extraction through the project and 75% of produce data was usable for research, but the time put in to obtain success was excessive.

An Analysis of the Purchasing Occupation.

ERIC Educational Resources Information Center

Lustic, Gary; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the purchasing occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Fourteen duties are broken down into a number of…

Budgeting: The Basics and Beyond. Learn at Home.

ERIC Educational Resources Information Center

Prochaska-Cue, Kathy; Sugden, Marilyn

Designed as an at-home course to help users develop a realistic budget plan and set up a workable record-keeping system, these course materials provide practical tips, ideas, and suggestions for budgeting. The course begins with a nine-step budgeting process which emphasizes communicating among family members, considering personal or family…

Opening Doors: Students' Perspectives on Juggling Work, Family, and College.

ERIC Educational Resources Information Center

Matus-Grossman, Lisa; Gooden, Susan

Information gathered in focus groups of current, former, and potential students at six community colleges was used to explore institutional and personal access and retention issues faced by students seeking a workable balance of their college, work, and family responsibilities. The six community colleges were as follows: Cabrillo College (Aptos,…

An Analysis of the Lithographic Printing Occupation.

ERIC Educational Resources Information Center

Innis, Gene A.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the lithographic printing occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Nine duties are broken down into a…

Planting Yellow-Poplar--Where We Stand Today

Treesearch

T.E. Russell

1977-01-01

Yellow-poplar can be established on a wide variety of sites with bare-rooted seedlings and standard planting techniques. Many past plantings have performed poorly because substandard seedlings have been planted on unsuitable sites and competing vegetation has not been adequately controlled. Research over the past two decades, however, provides workable guides for site...

The Choctaw Home-Centered Family Education Demonstration Project. Final Report.

ERIC Educational Resources Information Center

Quigley, Patrick A.; And Others

The final report of the four-year (1972-1976) Choctaw Family Education Project identifies the major goal, "to demonstrate a workable early childhood model for rural reservation groups," and consists of an executive summary, a comprehensive report, and a personalized report. Objectives of the project, carried out in 6 Choctaw reservation…

An Analysis of the Residential Remodeling Occupation.

ERIC Educational Resources Information Center

Scruggs, Kenneth

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the residential remodeling occupation. The analysis only briefly covers the many areas of residential remodeling. The document opens with a brief introduction followed by a job description. The bulk of the…

An Analysis of the Carpentry Occupation.

ERIC Educational Resources Information Center

McKinney, Oral O.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the carpentry occupation. The analysis starts with the progress of a house from the first study of the blueprints to the laying out of the excavations and continuing step-by-step until the interior finish…

Normalizing Effective Conflict Management through Academic Curriculum Integration: The Example of Workable Peace

ERIC Educational Resources Information Center

Smith, Stacie Nicole; Fairman, David

2004-01-01

Conflict resolution education (CRE) grew out of several parallel efforts: integrating social justice into schools, concerns about safety and youth violence, and desires to enhance responsible citizenship. Today, CRE encompasses, or is a component of, a broad range of initiatives in schools: violence prevention programs, diversity and tolerance…

Teaching Poetry for Children.

ERIC Educational Resources Information Center

Nist, Joan Stidham

Many prospective language arts teachers are unsure of what poetry really is. While it is impossible to present them with a definitive statement about the nature of poetry, they can be given a workable outline of the attributes of poetry to help them teach poetry to children. Rhythmic patterns can be emphasized to enhance children's enjoyment of…

An Analysis of the Information Receptionist Occupation.

ERIC Educational Resources Information Center

Sams, Helen C.; Snyder, Lois M.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the information receptionist occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Ten duties are broken down into a…

Workability of Mass Concrete. Report 2. Supplemental Proportioning Parameters.

DTIC Science & Technology

1996-09-01

Information given in the report shall not be used in advertising or sales promotion to indicate endorsement of this product by U.S. Government. 14 Chapter 2... SALES PROMOTION TO INDICATE EITHER EXPLICITLY OR IMPLICITLY ENDORSEMENT OF THIS PRODUCT BY THE U.S. GOVERNMENT. FORM EDITION OF 1 SEP 84 IS OBSOLETE

An Analysis of the Industrial Sales Occupation.

ERIC Educational Resources Information Center

Kitzmiller, Charles C.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the industrial sales occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eight duties are broken down into a number…

Target: Tomorrow. Second Career Planning for Military Retirees.

ERIC Educational Resources Information Center

Office of the Assistant Secretary of Defense for Manpower and Reserve Affairs (DOD), Washington, DC.

Intended for the career serviceman, this booklet attempts to provide the retiree with workable solutions to his own retirement situation and to assist him in resolving the transition between military and civilian life. The four steps the serviceman must take in approaching second career employment are given as follows: (1) review his experience,…

Teaching the Best Practice Way: Methods That Matter, K-12

ERIC Educational Resources Information Center

Daniels, Harvey; Bizar, Marilyn

2004-01-01

Everyone talks about "best practice" teaching--what does it actually look like in the classroom? How do working teachers translate complex curriculum standards into simple, workable classroom structures that embody exemplary instruction--and still let kids find joy in learning? In this book, the authors present seven basic teaching structures that…

Using TRIPS flexibilities to facilitate access to medicines

PubMed Central

Owoeye, Olasupo

2013-01-01

Abstract The problem of how to mitigate the impact of pharmaceutical patents on the delivery of essential medicines to the world’s poor is as far from being resolved as it has ever been. Extensive academic commentary and policy debate have achieved little in terms of practical outcomes. Although international instruments are now in place allowing countries to enact legislation that permits the generic manufacture of patented pharmaceuticals, many countries have not yet enacted appropriate legislation and most of those that have yet to make use of it. One major problem is that the requirements of international instruments and implementing legislation are seen as being so stringent as to be unworkable. This paper calls for fresh attempts to enact workable legislation that fits within the prescribed requirements of international law without going beyond them. It argues that high-income nations should refocus on their moral obligation to enact appropriate legislative mechanisms and provide appropriate incentives for their use. Draft legislation currently being considered in Australia is used to illustrate how workable legislative frameworks can be developed. PMID:23825881

Characterization of the Fe-Co-1.5V soft ferromagnetic alloy processed by Laser Engineered Net Shaping (LENS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kustas, Andrew B.; Susan, Donald F.; Johnson, Kyle L.

Processing of the low workability Fe-Co-1.5V (Hiperco® equivalent) alloy is demonstrated using the Laser Engineered Net Shaping (LENS) metals additive manufacturing technique. As an innovative and highly localized solidification process, LENS is shown to overcome workability issues that arise during conventional thermomechanical processing, enabling the production of bulk, near net-shape forms of the Fe-Co alloy. Bulk LENS structures appeared to be ductile with no significant macroscopic defects. Atomic ordering was evaluated and significantly reduced in as-built LENS specimens relative to an annealed condition, tailorable through selection of processing parameters. Fine equiaxed grain structures were observed in as-built specimens following solidification,more » which then evolved toward a highly heterogeneous bimodal grain structure after annealing. The microstructure evolution in Fe-Co is discussed in the context of classical solidification theory and selective grain boundary pinning processes. In conclusion, magnetic properties were also assessed and shown to fall within the extremes of conventionally processed Hiperco® alloys.« less

Characterization of the Fe-Co-1.5V soft ferromagnetic alloy processed by Laser Engineered Net Shaping (LENS)

DOE PAGES

Kustas, Andrew B.; Susan, Donald F.; Johnson, Kyle L.; ...

2018-02-21

Processing of the low workability Fe-Co-1.5V (Hiperco® equivalent) alloy is demonstrated using the Laser Engineered Net Shaping (LENS) metals additive manufacturing technique. As an innovative and highly localized solidification process, LENS is shown to overcome workability issues that arise during conventional thermomechanical processing, enabling the production of bulk, near net-shape forms of the Fe-Co alloy. Bulk LENS structures appeared to be ductile with no significant macroscopic defects. Atomic ordering was evaluated and significantly reduced in as-built LENS specimens relative to an annealed condition, tailorable through selection of processing parameters. Fine equiaxed grain structures were observed in as-built specimens following solidification,more » which then evolved toward a highly heterogeneous bimodal grain structure after annealing. The microstructure evolution in Fe-Co is discussed in the context of classical solidification theory and selective grain boundary pinning processes. In conclusion, magnetic properties were also assessed and shown to fall within the extremes of conventionally processed Hiperco® alloys.« less

Compressive strength of marine material mixed concrete

NASA Astrophysics Data System (ADS)

Adnan; Parung, H.; Tjaronge, M. W.; Djamaluddin, R.

2017-11-01

Many cement factories have been incorporated fly ash with clinker cement to produce blended cement. PCC is a type of blended cement incorporated fly ash that produced in Indonesia cement factories. To promote the sustainable development in the remote islands this present paper attempted to study the suitability of sea water, marine sand that available abundantly surround the remote island with Portland Composite Cement (PCC) and crushed river stone to produce concrete. Slump test was conducted to evaluate the workability of fresh concrete and also compressive strength with stress-strain relationship was carried out to evaluate the hardened concrete that cured with two curing condition (e.g. sea water curing, and tap water-wet burlap curing). Test result indicated that fresh concrete had proper workability and all hardened specimens appeared a good compaction result. Compressive strength of specimens cured which sea water was higher than the specimens which cured by tap water-wet burlap where stress-strain behavior of specimens made with sea water, marine sand, and PCC had similar behavior with specimens which made with PCC and tap water.

Evaluation of workability and strength of green concrete using waste steel scrap

NASA Astrophysics Data System (ADS)

Neeraja, D.; Arshad, Shaik Mohammed; Nawaz Nadaf, Alisha K.; Reddy, Mani Kumar

2017-11-01

This project works on the study of workability and mechanical properties of concrete using waste steel scrap from the lathe industry. Lathe industries produce waste steel scrap from the lathe machines. In this study, an attempt is made to use this waste in concrete, as accumulation of waste steel scrap cause disposal problem. Tests like compressive test, split tensile test, NDT test (UPV test) were conducted to determine the impact of steel scrap in concrete. The percentages of steel scrap considered in the study were 0%, 0.5%, 1%, 1.5%, and 2% respectively by volume of concrete, 7 day, 28 days test were conducted to find out strength of steel scrap concrete. It is observed that split tensile strength of steel scrap concrete is increased slightly. Split tensile strength of Steel scrap concrete is found to be maximum with volume fraction of 2.0% steel scrap. The steel scrap gives good result in split tensile strength of concrete. From the study concluded that steel scrap can be used in concrete to reduce brittleness of concrete to some extent.

Cure Cycle Design Methodology for Fabricating Reactive Resin Matrix Fiber Reinforced Composites: A Protocol for Producing Void-free Quality Laminates

NASA Technical Reports Server (NTRS)

Hou, Tan-Hung

2014-01-01

For the fabrication of resin matrix fiber reinforced composite laminates, a workable cure cycle (i.e., temperature and pressure profiles as a function of processing time) is needed and is critical for achieving void-free laminate consolidation. Design of such a cure cycle is not trivial, especially when dealing with reactive matrix resins. An empirical "trial and error" approach has been used as common practice in the composite industry. Such an approach is not only costly, but also ineffective at establishing the optimal processing conditions for a specific resin/fiber composite system. In this report, a rational "processing science" based approach is established, and a universal cure cycle design protocol is proposed. Following this protocol, a workable and optimal cure cycle can be readily and rationally designed for most reactive resin systems in a cost effective way. This design protocol has been validated through experimental studies of several reactive polyimide composites for a wide spectrum of usage that has been documented in the previous publications.

Sustainability, Eco-Point and Engineering Performance of Different Workability OPC Fly-Ash Mortar Mixes.

PubMed

Razi, Putri Zulaiha; Abdul Razak, Hashim; Khalid, Nur Hafizah A

2016-05-06

This study investigates the engineering performance and CO₂ footprint of mortar mixers by replacing Portland cement with 10%, 20%, 40% and 60% fly ash, a common industrial waste material. Samples of self-compacting mortar (SCM) were prepared with four different water/binder ratios and varying dosages of superplasticizer to give three ranges of workability, i.e. , normal, high and self-compacting mortar mix. The engineering performance was assessed in term of compressive strength after designated curing periods for all mixes. CO₂ footprint was the environmental impact indicator of each production stage. The optimum mix obtained was at 10% replacement rate for all mixes. Total production emission reduced by 56% when the fly ash replacement rate increased from 0% to 60% (maximum). This is translated to a reduction of 80% in eco-points (assuming that the energy consumption rate of production with 0% fly ash is at 100%). Such re-utilization is encouraged since it is able to reduce possible soil toxicity due to sulfur leaching by 5% to 27% and landfill area by 15% to 91% on average.

Hot Deformation Behavior and Intrinsic Workability of Carbon Nanotube-Aluminum Reinforced ZA27 Composites

NASA Astrophysics Data System (ADS)

Liu, Yang; Geng, Cong; Zhu, Yunke; Peng, Jinfeng; Xu, Junrui

2017-04-01

Using a controlled thermal simulator system, hybrid carbon nanotube-aluminum reinforced ZA27 composites were subjected to hot compression testing in the temperature range of 473-523 K with strain rates of 0.01-10 s-1. Based on experimental results, a developed-flow stress model was established using a constitutive equation coupled with strain to describe strain softening arising from dynamic recrystallization. The intrinsic workability was further investigated by constructing three-dimensional (3D) processing maps aided by optical observations of microstructures. The 3D processing maps were constructed based on a dynamic model of materials to delineate variations in the efficiency of power dissipation and flow instability domains. The instability domains exhibited adiabatic shear band and flow localization, which need to be prevented during hot processing. The recommended domain is predicated to be within the temperature range 550-590 K and strain rate range 0.01-0.35 s-1. In this state, the main softening mechanism is dynamic recrystallization. The results from processing maps agree well with the microstructure observations.

Sustainability, Eco-Point and Engineering Performance of Different Workability OPC Fly-Ash Mortar Mixes

PubMed Central

Razi, Putri Zulaiha; Abdul Razak, Hashim; Khalid, Nur Hafizah A.

2016-01-01

This study investigates the engineering performance and CO2 footprint of mortar mixers by replacing Portland cement with 10%, 20%, 40% and 60% fly ash, a common industrial waste material. Samples of self-compacting mortar (SCM) were prepared with four different water/binder ratios and varying dosages of superplasticizer to give three ranges of workability, i.e., normal, high and self-compacting mortar mix. The engineering performance was assessed in term of compressive strength after designated curing periods for all mixes. CO2 footprint was the environmental impact indicator of each production stage. The optimum mix obtained was at 10% replacement rate for all mixes. Total production emission reduced by 56% when the fly ash replacement rate increased from 0% to 60% (maximum). This is translated to a reduction of 80% in eco-points (assuming that the energy consumption rate of production with 0% fly ash is at 100%). Such re-utilization is encouraged since it is able to reduce possible soil toxicity due to sulfur leaching by 5% to 27% and landfill area by 15% to 91% on average. PMID:28773465

Workability and mental wellbeing among therapeutic prison officers.

PubMed

Walker, E J; Jackson, C A; Egan, H H; Tonkin, M

2015-10-01

Previous research has examined how age and health can shape workability (WA). This study seeks to explore how a lack of WA (inability) may affect the health of the employee. To explore the effects of work inability on mental wellbeing among therapeutic prison officers. An anonymous cross-sectional study of prison officers conducted in a category B English prison using the Work Ability Index (WAI) and General Health Questionnaire-28 (GHQ). Fifty-seven officers (59%) participated and of those 95% achieved GHQ caseness. Officers with poorer WA reported significantly higher GHQ scores. Work inability for mental demands had significant associations with anxiety (β = -0.58, 95% CI -4.21 to -1.88, particularly sleep loss; Pearson's r = -0.66). Our findings present clear associations between poor WA and its impact upon mental wellbeing. The results of this study may help to focus on areas for intervention such as improving WA and promoting mental wellbeing. © The Author 2015. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Petro-state constraints on health policy: guidelines for workable reform in Venezuela.

PubMed

Trujillo, Antonio J

2004-01-01

This article reviews the performance of the Venezuelan health care sector and suggests guidelines for workable health policy under difficult conditions. Two special circumstances constrain policy options. First, Venezuelans share a traditional value, solidarity, which includes a strong desire for equity. Reforms must comply with this norm to succeed. Second, foreign sales of state-controlled oil constitute the bulk of the government budget and the gross domestic product (GDP). Petroleum market fluctuations expose the country to extreme economic cycles. In response, policy making and stakeholders adopt a rentier attitude, focusing on preserving or enlarging entitlements to government oil monies. The side effects of this largesse include poor productivity, a weak private sector, a widespread sense of entitlement without accountability, and a crippled state which controls most of the available resources yet is unable to effectively tax, regulate, steer the economy, or pursue long-term policies. The health care sector shares these problems. As a result, Venezuela's health systems are fragmented, poorly coordinated, excessively centralized, inequitable, and ineffective. Policies to improve public health and public and private medical care must take into account these constraints.

Making the Journey: Being and Becoming a Teacher of English Language Arts. Second Edition.

ERIC Educational Resources Information Center

Christenbury, Leila

This book takes a look at the realities of classroom life, offering specific suggestions for dealing effectively with today's students. More than a compendium of activities, the first edition of the book introduced educators to a philosophy of teaching illustrated and implemented by workable, realistic techniques. The second edition of the book…

Teamwork, Soft Skills, and Research Training.

PubMed

Gibert, Anaïs; Tozer, Wade C; Westoby, Mark

2017-02-01

We provide a list of soft skills that are important for collaboration and teamwork, based on our own experience and from an opinion survey of team leaders. Each skill can be learned to some extent. We also outline workable short courses for graduate schools to strengthen teamwork and collaboration skills among research students. Copyright © 2016 Elsevier Ltd. All rights reserved.

An Analysis of the Real Estate Property Managing Occupation.

ERIC Educational Resources Information Center

Bryan, James E.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the real estate property manager occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eleven duties are broken down…

An Analysis of the Payroll Clerking Occupation.

ERIC Educational Resources Information Center

Peal, Sharyn; Rose, Virginia

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the payroll clerk occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Ten duties are broken down into a number of…

Proceedings of the Annual Western Regional Conference on Testing Problems (20th, Oakland, California, May 7, 1971).

ERIC Educational Resources Information Center

Educational Testing Service, Princeton, NJ.

Conference papers include: "The 'New Approach of the California State Colleges'" (Glenn S. Dumke); "Toward Institutional Goal-Consciousness" (Richard E. Peterson); "The Commission on Non-traditional Study - Who Needs It?" (John A. Valentine); "The Impact of Mandated Evaluation on Education" (Alexander I. Law); "A Workable Solution to the Demand…

Legal Issues & Education Technology: A School Leader's Guide. An ITTE Technology Leadership Network Special Report. Second Edition.

ERIC Educational Resources Information Center

Darden, Edwin C., Ed.

This book is intended to help school leaders achieve a workable balance that allows schools to take advantage of the educational and administrative benefits of digital technologies while protecting the district from disruptive and expensive litigation. Chapter 1, "Student Learning and the Law of School Technology," focuses on developing policies…

Plasmoid Propagation.

DTIC Science & Technology

1988-02-12

experimentally , a pulsed power system com- prising separate anode and cathode pulsers was designed and assembled. A double diode was developed to produce...be closed. To initiate this assessment, Mission Research Corporation (MRC) performed a two-year primarily experimental investigation of non - neutral...through from the cathode nad to be designed . Experimentation with several materials and setups produced a workable design , using nylon stocking hose

Prisoners of Time: Implementing a Block Schedule in the High School.

ERIC Educational Resources Information Center

Mistretta, Gerald M.; Polansky, Harvey B.

1997-01-01

A committee comprised of six veteran teachers, the principal, and one parent initiated East Lyme (Connecticut) High School's search for a workable school schedule. The alternative-day block schedule featured semester and full-year course formats, 85-minute time blocks, a 45-minute lunch/club/activity period, and a closed campus. A survey found…

When Dollars Follow Students: The Political Viability, Equity and Workability of Weighted Funding Formulas

ERIC Educational Resources Information Center

Deroche, Timothy R.; Cooper, Bruce S.; Ouchi, William G.

2004-01-01

For more than a decade, education reformers have admired the achievements of the Edmonton Public Schools in Canada, and school districts across the United States have attempted to replicate Edmonton's success with school-site decision making. However, most districts have stopped short of implementing one policy that is central to Edmonton's…

A Workable Balance: Report to Congress on Family and Medical Leave Policies.

ERIC Educational Resources Information Center

Women's Bureau (DOL), Washington, DC.

The competing demands of the workplace and the home have intensified over the last 25 years as the nation has experienced dramatic social and economic changes affecting businesses, employees, and families. In 1993, Congress passed the Family and Medical Leave Act (FMLA) to provide a national policy that supports families in their efforts to strike…

Back to the Agora: Workable Solutions for Small Urban School Facilities. ERIC Digest.

ERIC Educational Resources Information Center

Lawrence, Barbara Kent

The ancient Athenian "agora" functioned as a marketplace for ideas and commerce and offered an ideal place for teaching and learning. This digest suggests adapting such a model to modern needs and describes successful small schools that have done so while reducing costs. Research shows that small schools offer many advantages for…

A Comparison of Increment Core Sampling for Estimating Tree Specific Gravity

Treesearch

Michael A. Taras; Harold E. Wadlgren

1963-01-01

Increment cores have been used to evaluate such tree characteristics as age, rate of growth, percentage of various types of tissue, chemical composition, and density. Of the wood characteristics listed, density has come to be of considerable interest to numerous researchers, since it is highly correlated with the strength properties, workability, and weight of wood....

[Aerogenic risk factors and diagnosis of bauxite pneumoconiosis].

PubMed

Peshkova, A O; Roslaia, N A; Roslyĭ, O F; Likhacheva, E I; Fedoruk, A A; Slyshkina, T V; Vagina, E R

2013-01-01

The research purpose is an estimation of influence of the bauxite dust on the state of the bronchopulmonary system of workers. It has been indicated that exposure of the poor fibrogenic dust while the process of the bauxite ore extraction, results in development of pnevmokoniosis characterized by substantial ventilatory and haemodynamic disorders limiting the workability of patients.

An Analysis of the Auto Body Repair Occupation.

ERIC Educational Resources Information Center

Stranke, Edward J.; Speck, Samuel R.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the auto body mechanic occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eleven duties are broken down into a…

Open Learning in India: Evolution, Diversification and Reaching Out

ERIC Educational Resources Information Center

Sharma, Ramesh C.

2005-01-01

Distance education has a history of over four decades in India. There has been a vast growth in the number of learners who need education and thus also the corresponding channels of providing education. Due to the constraints of the traditional educational sector, open and distance learning has been found to be a workable alternative strategy in…

Reaching Common Ground: Advancing Business Participation in Restructuring Education. Supporting Leaders for Tomorrow, Occasional Paper #6.

ERIC Educational Resources Information Center

Siegel, Peggy M.; Smoley, Eugene R., Jr.

The differences and similarities between education and the private sector are analyzed as they both engage in efforts to fundamentally restructure their operations. To bridge the cultural gap between business and education, a workable strategy that advances direct and sustained private-sector involvement in education reform is proposed. Part 1 of…

An Analysis of the Waste Water Treatment Maintenance Mechanic Occupation.

ERIC Educational Resources Information Center

Clark, Anthony B.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the waste water treatment mechanics occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Twelve duties are broken…

Times Change, but This Ten-Year-Old School Plan Remains Fresh and Functional.

ERIC Educational Resources Information Center

Rist, Marilee C.

1989-01-01

The 1979 passive solar design for Meadow Park Elementary School (Irvine, California) was not used until 1986. Architects had incorporated workable energy-saving features that would give a sizable return on the investment. They maximized use of natural light and used solar features (clerestory windows and interior courtyards) to reduce heat…

Policy Development of Quality Assurance: A Critical Perspective on Past and Future Issues.

ERIC Educational Resources Information Center

van der Westhuizen, L. J.

2000-01-01

Provides an overview of the initiatives and development of policies to establish a workable quality assurance system for institutions of higher education in South Africa in the last decade. Notes challenges such as the government's emphasis on programs of study and its requirement that quality assurance systems include institutional auditing,…

An Analysis of the Television and Radio Service Occupation.

ERIC Educational Resources Information Center

Pomeroy, James W.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the television and radio service occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Eight duties are broken down…

76 FR 18254 - Proposed Information Collection Request (ICR) for the Family Medical Leave Act (FMLA) Employee...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-01

... WHD to determine how those policies affect the work-life balance of workers and the productivity and work flow of employers. The study enables DOL to shape future regulatory options, craft interpretive... Family and Medical Leave. The final report on this survey, titled ``A Workable Balance: Report to...

A preliminary test of estimating forest site quality using species composition in a southern Appalachian watershed

Treesearch

W. Henry McNab; David L. Loftis

2013-01-01

Characteristic arborescent communities of mesophytic or xerophytic species have long been recognized as indicative of forest site quality in the Southern Appalachians, where soil moisture availability is the primary environmental variable affecting productivity. But, a workable quantitative system of site classification based on species composition is not available. We...

Unwritten: (Re)Imagining FE as Social Purpose Education

ERIC Educational Resources Information Center

Mycroft, Lou

2018-01-01

Drawing on stories from ten years of social purpose teacher education in the UK, this paper assumes that the future of further education is still unwritten. It illustrates complex and workable ideas via a theorised sketch of the fictional Bee Learning Programme, an imagined education setting of the future. The narrative that follows is designed to…

Experimental autoimmune hearing loss

PubMed Central

Billings, Peter

2004-01-01

Understanding of autoimmune sensorineural hearing loss (ASNHL) has been hindered by the inaccessibility of the inner ear to biopsy and the lack of workable animal models. A report in this issue of the JCI describes a mouse model of CD4+ T cell–mediated ASNHL induced by immunization with peptides from the inner ear–specific proteins cochlin and β-tectorin. PMID:15085190

An Analysis of the Air Conditioning, Refrigerating and Heating Occupation.

ERIC Educational Resources Information Center

Frass, Melvin R.; Krause, Marvin

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the air conditioning, refrigerating, and heating occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Six duties are…

An Analysis of the Diesel Truck Mechanic Occupation.

ERIC Educational Resources Information Center

Kilo, Joseph L.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the diesel truck mechanic occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Thirteen duties are broken down into a…

Motor Development and Movement Experiences for Young Children (3-7).

ERIC Educational Resources Information Center

Gallahue, David L.

This book's main objective is to help teachers and parents deal more knowledgeably and effectively with children through the medium of movement. The book has been written in such a manner that current theory, research, and practical application are merged into a workable whole. The first five chapters provide the reader with a basis of knowledge…

Classroom Software for the Information Age. Technical Report No. 23.

ERIC Educational Resources Information Center

Sheingold, Karen; And Others

Consumers and producers of educational software must make decisions about what kind of software to buy and create. Both groups must base these decisions on criteria that consider what it is important to learn in our technological era, what is workable, and what is currently practical and cost-effective. Five criteria that are central to these…

Hang in there! Quick takes on Y2K.

PubMed

Lewis, A G; Weingart, V S

1998-11-01

Cliffhangers in movies are great fun. But not in real life. Think Y2K. If you haven't scripted a way to beat the millennium bug, there are workable solutions that can be created in six months. Here's how to begin production: Prioritize activities, expenditures and resources, and apply them to the most vital problems first.

An Analysis of the Real Estate Occupation.

ERIC Educational Resources Information Center

Harestad, Clifford E.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the real estate occupation. It represents an accounting of what must be done, but not how the entire cycle of a residential sale is completed through the services of a real estate person and the…

Directions for Success: Career Assessment and Planning for Learning Disabled High School Students, 1985-86.

ERIC Educational Resources Information Center

Kaplan, Linda; And Others

This four-part report describes Directions for Success, a school-college collaborative project between Middlesex Community College and 15 area school districts designed to provide learning disabled students and their parents with career assessment services and access to information which will enable them to make workable, long-range career plans.…

Proposed Multiconjugate Adaptive Optics Experiment at Lick Observatory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, B J; Gavel, D T; Flath, L M

2001-08-15

While the theory behind design of multiconjugate adaptive optics (MCAO) systems is growing, there is still a paucity of experience building and testing such instruments. We propose using the Lick adaptive optics (AO) system as a basis for demonstrating the feasibility/workability of MCAO systems, testing underlying assumptions, and experimenting with different approaches to solving MCAO system issues.

Non-Formal Vocational Education in Uganda: Practical Empowerment through a Workable Alternative

ERIC Educational Resources Information Center

Blaak, Marit; Openjuru, George L.; Zeelen, Jacques

2013-01-01

This article reflects on the potential of non-formal vocational education in Uganda to improve the quality of life of those excluded from formal education. Based on an exploration of humanizing development theorists Sen, Freire and Nyerere, together with two case studies, practical empowerment is described as a desirable outcome of education for…

PLUTONIUM-URANIUM-TITANIUM ALLOYS

DOEpatents

Coffinberry, A.S.

1959-07-28

A plutonium-uranium alloy suitable for use as the fuel element in a fast breeder reactor is described. The alloy contains from 15 to 60 at.% titanium with the remainder uranium and plutonium in a specific ratio, thereby limiting the undesirable zeta phase and rendering the alloy relatively resistant to corrosion and giving it the essential characteristic of good mechanical workability.

Military Power in a Democratic Society. Teacher and Student Manuals.

ERIC Educational Resources Information Center

Zarlengo, F. John

This unit focuses on the classic problem of the place of military power in a democratic society. Early sections examine the relationship between civil and military authority as developed in colonial America and written into the Constitution. The second half of the unit invites consideration of the relevance and workability of the earlier tradition…

The Pros and Cons of Individualized Programmed Instruction for Indian Students. A Position Paper....

ERIC Educational Resources Information Center

Corcoran, Bert W.

Based on observations and experiences in a Title III (Elementary and Secondary Education Act) project to individualize instruction in the ungraded Rocky Boy Elementary School (grades 1-6, Rocky Boy Indian Reservation, Box Elder, Montana), this position paper considers the problem of finding a suitable or workable curriculum and classroom climate…

Marvelous Signals: The Usefulness of the In-Class Essay.

ERIC Educational Resources Information Center

Crafton, John Micheal

Based on his experience of being trained in a process-centered pedagogy and of working in a product-centered program, a writing instructor discovers that the in-class essay is not only a useful or workable part of a regressive curriculum, but that it is effective and necessary for any progressive process orientation as well. Pragmatic, ethical,…

Educating for a More Public Journalism: Public Journalism and Its Challenges to Journalism Education.

ERIC Educational Resources Information Center

Haas, Tanni

Given the increasing influence of public journalism on the daily routines of newspapers across the United States, students need to be taught how to find a workable balance between consulting and reporting on conventional information sources and consulting and reporting on the perspectives provided by ordinary citizens. This paper discusses ways in…

An Analysis of the Dental Assisting Occupation.

ERIC Educational Resources Information Center

Hough, Sharon L.; And Others

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the dental assistant occupation. The document opens with a brief introduction followed by a job description. The bulk of the document is presented in table form. Six duties are broken down into a number of…

AB1417 Performance Framework for the California Community Colleges: A Report to the Legislature, Pursuant to AB1417

ERIC Educational Resources Information Center

Research and Planning Group for California Community Colleges (RP Group), 2005

2005-01-01

This report to the Legislature and Governor provides recommendations on the design of a workable structure for the annual evaluation of district-level performance for California Community College districts. Under contract with the California Community Colleges Chancellor's Office, a six-member panel of the Research and Planning Group for…

Making It Rich and Personal: Crafting an Institutional Personal Learning Environment

ERIC Educational Resources Information Center

White, Su; Davis, Hugh C.

2011-01-01

Many of the communities interested in learning and teaching technologies within higher education now accept the view that a conception of personal learning environments provides the most realistic and workable perspective of learners' interactions with and use of technology. This view may not be reflected in the behaviour of those parts of a…

Changes in Attitudes Toward Environmental Education and Selected Teaching Behaviors of Teachers Participating in Environmental Education Workshops.

ERIC Educational Resources Information Center

Myer, Teresa A.

This study examined four teacher in-service environmental education programs to: (1) suggest a workable evaluative model for such programs; (2) assess their content with respect to stated activities and objectives; and (3) determine whether or not the experiences correlated with changes in selected teaching behaviors. The research design included…

Learning Relational Ways of Being: What Globally Engaged Scholars Have Learned about Global Engagement and Sustainable Community Development

ERIC Educational Resources Information Center

Ulrich, Mary Eileen

2016-01-01

How does higher education contribute to finding workable and lasting solutions to complex social issues that face communities globally today? How does higher education contribute to global sustainable development goals? The scholarship of engagement encourages faculty, scholars, and students to work together with communities on solutions to…

Achieving Youth Employment and National Security in Nigeria: TVET Imperatives

ERIC Educational Resources Information Center

Ogbuanya, T. C.; Ofonmbuk, Michael

2015-01-01

The rate of unemployment in Nigeria is alarming and could promote social vices some of which are kidnapping, armed robbery, child trafficking, Cultism, Drug peddling and ritual killing. These social vices could in no small measure constitute a threat to national security as a matter of fact. Therefore, the development of a workable Technical and…

Testimony from Learning Disabled College Writers on the Efficacy of Word Processing in their Writing Process. Working Paper.

ERIC Educational Resources Information Center

Collins, Terence; Price, Lynda

As part of a three-year federally funded research program intended to shed light on the writing processes of learning disabled college-aged writers (with special emphasis on the use of technology in creating workable mainstreamed curricula), this paper records in an interview format the responses of students to the program, including word…

Construction of a microscopic agent-based model for firms' dynamics

NASA Astrophysics Data System (ADS)

Iyetomi, Hiroshi; Aoyama, Hideaki; Fujiwara, Yoshi; Ikeda, Yuichi; Kaizoji, Taisei; Soma, Wataru

2005-07-01

A workable microscopic model for firms' dynamics has been constructed. The model consists of firm agents and a bank agent dynamics of which are described by balance sheets. The size distribution of firms and the temporal evolution of the bank show critical dependence on whether or not firms use perfect information on their financial conditions to draw up next production plans.

FABRICATION OF URANIUM-ALUMINUM ALLOYS

DOEpatents

Saller, H.A.

1959-12-15

A process is presented for producing a workable article of a uranium- aluminum alloy in which the uranium content is between 14 and 70% by weight; aluminum powder and powdered UAl/sub 2/, UAl/sub 3/, UAl/sub 5/, or UBe/sub 9/ are mixed, and the mixture is compressed into the shape desired and sintered at between 450 and 600 deg C.

Innovative and Workable Ideas for Building Schools. Public/Private Partnerships: A New Way To Fund and Build Schools.

ERIC Educational Resources Information Center

Guhse, David

This report presents case studies illustrating successful public-private financing of school construction. The efforts occurred in Canada, Florida, South Carolina, New York, the District of Columbia, and Texas. The case studies are offered to encourage policy makers in Virginia to consider such an approach to meet the state's school construction…

Effect of Temperature on Acoustic Evaluation of Standing trees and logs: Part 1-Laboratory investigation

Treesearch

Shan Gao; Xiping Wang; Lihai Wang; R. Bruce. Allison

2012-01-01

The goals of this study were to investigate the effect of environment temperature on acoustic velocity of standing trees and green logs and to develop workable models for compensating temperature differences as acoustic measurements are performed in different climates and seasons. The objective of Part 1 was to investigate interactive effects of temperature and...

METHOD OF SUPPRESSING UAl$sub 4$ FORMATION IN U-Al ALLOYS

DOEpatents

Picklesimer, M.L.; Thurber, W.C.

1960-08-23

A method is given for suppressing the formation of UAl/sub 4/ in uranium- - aluminum alloys, thereby rendering these alloys more easily workable. The method comprises incorporating in the base alloy a Group Four element selected from the group consisting of Si, Ti, Ge, Zr, and Sn, the addition preferably being within the range of 0.5to20at.%.

Finding Common Ground: Creating the Library of the Future without Diminishing the Library of the Past. The New Library Series.

ERIC Educational Resources Information Center

LaGuardia, Cheryl, Ed.; Mitchell, Barbara A., Ed.

Adapting today's libraries to better serve tomorrow's needs challenges even the most forward-thinking library staff. This book offers practical, workable solutions from several authorities in the industry. Fifty-five conference papers are included and divided into the following subject areas: "Technology and the Network: Daimons or Demons?";…

Utilization of the Eastern Hardwood Resource by the Hardwood Sawmilling Industry

Treesearch

William Luppold; John Baumgras; John Baumgras

2001-01-01

The eastern hardwood resource contains numerous species that differ in grain, color, texture, and workability. Because the value of hardwoods is derived from appearance, these variations in physical attributes can cause the price for identical grades of hardwood lumber to vary by as much as 600% between species. As a result, there is incentive for primary processors to...

"You Can See the Quality in Front of Your Eyes": Grounding Academic Standards between Rationality and Interpretation

ERIC Educational Resources Information Center

Bloxham, Sue

2012-01-01

This article considers the failure of theory to provide a workable model for academic standards in use. Examining the contrast between theoretical perspectives, it argues that there are four dimensions for which the academy has failed to provide an adequate theoretical account of standards: documented or tacit knowledge of standards; norm or…

Soviet Maintenance Training and the Technological Imperative.

DTIC Science & Technology

1980-06-01

competition arid obligations, the rise of innovators, inventors arid rationalizers , as well as thle irmportance placed on technolo2 ical awareness are...the Communist Party in the training process, socialist competition and obligations, the use of innovators, inventors and rationalizers , as well as the...current military-technical environment . The paper concludes that the Soviets have a workable and relatively effective system for peacetime maintenance

Writing: The Research Paper. Postsecondary Intervention Model for Learning Disabilities. Study Manual #3.

ERIC Educational Resources Information Center

Friedman, Brenda G.; And Others

The manual is intended to help students with language learning disabilities master the academic task of research paper writing. A seven-step procedure is advocated for students and their tutors: (1) select a workable topic, then limit and focus it; (2) use library references to identify sources from which to prepare a working bibliography; (3)…

A Special Section on International Education--What We Can Learn from Russia's Schools

ERIC Educational Resources Information Center

Post, Becky

2005-01-01

Russia's educational system has been successful in producing graduates who excel in mathematics, the sciences, and foreign languages, but these are not the only areas that we might look to as models. Russian and American cultures and educational practices differ in significant ways, and not all of the practices described here would be workable in…

When Measures Change over Time: A Workable Solution for Analysing Change and Growth across Multiple Waves

ERIC Educational Resources Information Center

Lloyd, Jennifer E. V.; Zumbo, Bruno D.; Siegel, Linda S.

2009-01-01

In the past 20 years, the analysis of individual change has become a key focus in educational research. There are several parametric analyses that centre upon quantifying change. Some researchers state that such analyses should only occur if the measure itself remains completely unchanged across waves, arguing that it is not possible to link or…

JPRS Report, China.

DTIC Science & Technology

1991-10-28

Markets [TIGAI XINXI No 14] ......................................... 28 Cotton Purchases Increased To Stabilize Supply [CHINA DAILY 14 Oct...workable measures, and they have received in markets . After 10 years of reform, an over- begun to take action in accordance with the separate whelming...lack the boldness Village and at Taihuangshan Village in Ganquan, and needed to develop markets . In many things they do, they the very large scale on

Managers Confront Competing Practical, Legal, and Ethical Claims: A Comprehensive Teaching Case

ERIC Educational Resources Information Center

McAdams, Tony

2009-01-01

Law classes help reveal the successes of the American legal system. Students observe that the law is honorable, workable, and effective. At the same time, law classes offer the opportunity to look at those situations where the legal system sometimes struggles to achieve its justice goals. Students certainly need to learn that lesson, but they also…

76 FR 32991 - Request (ICR) for the Family Medical Leave Act (FMLA) Employee and Employer Surveys; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-07

... analysis of private sector FMLA policies allows WHD to determine how those policies affect the work-life balance of workers and the productivity and work flow of employers. The study enables DOL to shape future... Commission on Family and Medical Leave. The final report on this survey, titled ``A Workable Balance: Report...

It Is Not Just about the Schedule: Key Factors in Effective Reference Desk Scheduling and Management

ERIC Educational Resources Information Center

Sciammarella, Susan; Fernandes, Maria Isabel; McKay, Devin

2008-01-01

Reference desk scheduling is one of the most challenging tasks in the organizational structure of an academic library. The ability to turn this challenge into a workable and effective function lies with the scheduler and indirectly the cooperation of all librarians scheduled for reference desk service. It is the scheduler's sensitivity to such…

A Framework for Action To Make Private Housing Lead-Safe: A Proposal To Focus National Attention.

ERIC Educational Resources Information Center

Alliance to End Childhood Lead Poisoning, Washington, DC.

This framework sets forth detailed proposals that are crucial to eliminating the epidemic of childhood lead poisoning in the United States. Private housing units can and must be made lead-safe, and this framework is designed to achieve that goal through specific requirements for property owners, a workable schedule, and mechanisms that reinforce…

Your Family Land: Legacy or Memory? An Introduction to the Family Land Protection Process

Treesearch

USDA Forest Service, Northeastern Area, State and Private Forestry

2008-01-01

If you have this perspective, protecting your land from development is a task you certainly can accomplish. Virtually every situation is workable and every problem can be solved. It does require some planning and decisionmaking; however, so the sooner you start the better. Experience has shown that the number one obstacle to the protection of family land...

Systems in Tension: Perceptions of Business and Education in Partnership

ERIC Educational Resources Information Center

Despres, Blane Rolland

2003-01-01

The aim of this research project has been to map the range of perceptions of a sample of people concerning business in partnership with education. From the range of perceptions held by the participants in this dissertation, we can conclude that partnering is not a simple matter of two parties agreeing to some workable union between them for mutual…

Teaching French Vocabulary to English Speaking Students. A Comprehensive and Eclectic Approach.

ERIC Educational Resources Information Center

Howlett, Frederick G.

The greatest need of language teachers today is a workable approach to teaching vocabulary. This is essential if students are to be enabled to achieve communicative competence, that is, to make a transfer from the textbook to the real world of French, as reflected in the French media. An effective and comprehensive approach to teaching vocabulary…

Life Span as the Measure of Performance and Learning in a Business Gaming Simulation

ERIC Educational Resources Information Center

Thavikulwat, Precha

2012-01-01

This study applies the learning curve method of measuring learning to participants of a computer-assisted business gaming simulation that includes a multiple-life-cycle feature. The study involved 249 participants. It verified the workability of the feature and estimated the participants' rate of learning at 17.4% for every doubling of experience.…

School Discipline: Best Practices for Administrators. Second Edition

ERIC Educational Resources Information Center

Rosen, Louis

2005-01-01

In this book, the author offers the best ideas and most workable discipline practices from more than 1,000 school leaders. The book is loaded with updates and gives administrators all the tools they need to create a safe environment, from dealing effectively with the 5% of students who take up 90% of their time, to creating a positive public image…

Building Jobs, Rebuilding Lives: Placing Ex-Offenders with Employers in the Residential and Light Commercial Construction Industry.

ERIC Educational Resources Information Center

Home Builders Inst., Washington, DC.

This guide presents a focused, structured method of facilitating ex-offender employment. Section 1 takes classic marketing techniques and adapts them to the needs of the particular situation, placing ex-offenders in meaningful employment. The set of specific requirements for creating a workable marketing plan is condensed to six basic steps that…

Advanced Solar Observatory (ASO) accommodations requirements study

NASA Technical Reports Server (NTRS)

1989-01-01

Results of an accommodations analysis for the Advanced Solar Observatory on Space Station Freedom are reported. Concepts for the High Resolution Telescope Cluster, Pinhole/Occulter Facility, and High Energy Cluster were developed which can be accommodated on Space Station Freedom. It is shown that workable accommodations concepts are possible. Areas of emphasis for the next stage of engineering development are identified.

Measurement of Workability of Fresh Concrete Using a Mixing Truck

PubMed Central

Amziane, Sofiane; Ferraris, Chiara F.; Koehler, Eric P.

2005-01-01

The main objective of this study is to evaluate the workability of fresh portland cement concrete while it is still in the mixing truck by determining fundamental rheological parameters (plastic viscosity and yield stress). Nine concrete mixtures with different values of yield stress and plastic viscosity were tested in a concrete truck. The measurements made with the truck were based on the typical method of determining the flow behavior in a traditional fluid rheometer; that is, the shear rate in the mixing truck was swept from high to low by varying the rotation speed of the drum. The results of these experiments are discussed and compared with data provided by the ICAR rheometer, a portable rheometer designed for measuring concrete rheology. The test results indicate that the mixing truck equipment is sufficiently sensitive to detect differences in yield stress, slump, and plastic viscosity. However, the plastic viscosity determined by the truck measurement did not correlate with plastic viscosity as measured by the ICAR rheometer, while the yield stress determined by the truck measurement did correlate well with the measured slump and the ICAR rheometer results Suggestions are given on how to improve the mixing truck for better use as a rheometer. PMID:27308103

VALUE: A trans-disciplinary research project - and some challenges in its implementation

NASA Astrophysics Data System (ADS)

Huebener, Heike

2013-04-01

The EU-COST-action VALUE ("Validating and Integrating Downscaling Methods for Climate Change Research") is composed as a trans-disciplinary network activity, meaning that stakeholders and end-users not only from different scientific disciplines (i.e. inter-disciplinary research) but also from outside science are included in the design, planning and progress of the project. This gives the optimal chance to produce really workable project results for the intended end-users. However, some considerable challenges lie this way. These challenges start with identifying and motivating the target-stakeholders, they cover communication in different user-specific languages and reach as far as the question of the freedom of research when under the prompting of politics or economy. We will cover only some of the mentioned challenges; focusing on the identification of the target-stakeholders or end-users, their motivation to participate in the project and on some typical problems arising in this constellation. First experiences from the project will be presented. The aim of the presentation is to instigate discussion on developing workable project structures for trans-disciplinary research, as this will become more and more relevant in future research funding.

Utilization of fly ash as partial sand replacement in oil palm shell lightweight aggregate concrete

NASA Astrophysics Data System (ADS)

Nazrin Akmal, A. Z. Muhammad; Muthusamy, K.; Mat Yahaya, F.; Hanafi, H. Mohd; Nur Azzimah, Z.

2017-11-01

Realization on the increasing demand for river sand supply in construction sector has inspired the current research to find alternative material to reduce the use of natural sand in oil palm shell lightweight aggregate concrete (OPS LWAC) production. The existence of fly ash, a by-product generated from coal power plant, which pose negative impact to the environment when it is disposed as waste, were used in this research. The effect of fly ash content as partial sand replacement towards workability and compressive strength of OPS lightweight aggregate concrete were investigated. Four concrete mixes containing various percentage of fly ash that are 0%, 10%, 20% and 30% by weight of sand were used in the experimental work. All mixes were cast in form of cubes before subjected to water curing until the testing age. Compressive strength test were conducted at 1, 3, 7 and 28 days. The finding shows that the workability of the OPS LWAC decreases when more fly ash are used as sand replacement. It was found that adding of 10% fly ash as sand replacement content resulted in better compressive strength of OPS LWAC, which is higher than the control mix.

Mechanical and Physical Performance of Concrete Including Waste Electrical Cable Rubber

NASA Astrophysics Data System (ADS)

Taner Yildirim, Salih; Pelin Duygun, Nur

2017-10-01

Solid wastes are important environmental problem all over the World. Consumption of the plastic solid waste covers big portion within the total solid waste. Although a numerous plastic material is subjected to the recycling process, it is not easy to be destroyed by nature. One of the recommended way to prevent is to utilize as an aggregate in cement-based material. There are many researches on use of recycling rubber in concrete. However, studies on recycling of waste electrical cable rubber (WECR) in concrete is insufficient although there are many research on waste tyre rubbers in concrete. In this study, fine aggregate was replaced with WECR which were 5%, 10%, and 15 % of the total aggregate volume in the concrete and researched workability, unit weight, water absorption, compressive strength, flexural strength, ultrasonic pulse velocity, modulus of elasticity, and abrasion resistance of concrete. As a result of experimental studies, increase of WECR amount in concrete increases workability due to lack of adherence between cement paste and WECR, and hydrophobic structure of WECR while it influences negatively mechanical properties of concrete. It is possible to use WECR in concrete taking into account the reduction in mechanical properties.

Studying hardness, workability and minimum bending radius in selectively laser-sintered Ti–6Al–4V alloy samples

NASA Astrophysics Data System (ADS)

Galkina, N. V.; Nosova, Y. A.; Balyakin, A. V.

2018-03-01

This research is relevant as it tries to improve the mechanical and service performance of the Ti–6Al–4V titanium alloy obtained by selective laser sintering. For that purpose, sintered samples were annealed at 750 and 850°C for an hour. Sintered and annealed samples were tested for hardness, workability and microstructure. It was found that incomplete annealing of selectively laser-sintered Ti–6Al–4V samples results in an insignificant reduction in hardness and ductility. Sintered and incompletely annealed samples had a hardness of 32..33 HRC, which is lower than the value of annealed parts specified in standards. Complete annealing at temperature 850°C reduces the hardness to 25 HRC and ductility by 15...20%. Incomplete annealing lowers the ductility factor from 0.08 to 0.06. Complete annealing lowers that value to 0.025. Complete annealing probably results in the embrittlement of sintered samples, perhaps due to their oxidation and hydrogenation in the air. Optical metallography showed lateral fractures in both sintered and annealed samples, which might be the reason why they had lower hardness and ductility.

Fever and rash.

PubMed

Schlossberg, D

1996-03-01

The combination of fever and rash comprises an extensive differential diagnosis. Many of the causes of this presentation are life-threatening. In this article, rashes are categorized as petechial, maculopapular, vesicular, erythematous, and urticarial. Each type of rash is then divided into infectious etiologies, both treatable and nontreatable, and noninfectious etiologies. It is usually possible to arrive at a workable differential diagnosis when clinical, historical, and epidemiologic factors are considered.

Digital Adultery, "Meta-Anon Widows," Real-World Divorce, and the Need for a Virtual Sexual Ethic

NASA Astrophysics Data System (ADS)

Spencer, William David

Ethical issues that have emerged around relationships in virtual worlds can inform the way we approach the ethics of human/robot relationships. A workable ethic would be one that treats marriage as an enduring human institution and, while we value robots as worthy works of our hands, they are inappropriate partners for marital or sexual relationships.

Quality mind-set overcomes barriers to success.

PubMed

Anderson, C A; Daigh, R D

1991-02-01

To remove hindrances to fiscal strength, a healthcare facility needs a long-term, organization-wide strategy. Total quality management (TQM) can offer such a solution, but it requires a revised management philosophy. Under TQM, a hospital must adopt a workable definition of quality; develop a customer orientation; form organizational teams to study and revise work processes; involve all employees in quality efforts; and strive for continuous improvements.

The First 60 Days

DTIC Science & Technology

1987-03-23

solution . Using the battalion training NCO, senior guidance counselor, operations NCO, SGM, XO and operations officer as trainers will assist both the... towsrd justification of additional advertising funds, if needed. SProviding a workable Total Army Involvement in Recruiting (TAIR) plan on a quarterly... solution to this problem. 0 Have your CLT visit local reserve canters for assistance in gaining access to schools. Many times, members of the reserve units

The need for expanded exploration of matter-antimatter annihilation for propulsion application

NASA Technical Reports Server (NTRS)

Massier, P. F.

1982-01-01

The use of matter-antimatter annihilation as a propulsion application for interstellar travel is discussed. The physical basis for the superior energy release in such a system is summarized, and the problems associated with antimatter production, collection and storage are assessed. Advances in devising a workable propulsion system are reported, and the parameters of an antimatter propulsion system are described.

DoD Implementation of the Better Buying Power Initiatives

DTIC Science & Technology

2012-12-01

statutory measures (Budget Control Act of 2011), Congress has been directed to face this problem and provide a workable solution or face the evils...Defense Support Program (DSP) to provide the capabilities that the SBIRS has had problems delivering (Richelson, 2007; Werner, 2011). The purpose of the...Defense David Packard took office. They were keen on addressing the problems plaguing defense acquisition: excessive centralization, inefficiencies

Notes of a Racial Caste Baby. Color Blindness and the End of Affirmative Action. Critical America Series.

ERIC Educational Resources Information Center

Fair, Bryan K.

This book is a defense of remedial affirmative action and an assertion that it is a policy that is a fair and workable solution to the chronic problem of racial caste in the United States. The personal narrative of the author, eighth of 10 children born to a single mother on public assistance, is combined with the discussion of American history…

A School for Everyone. Design for a Middle, Junior, or Senior High School that Combines the Old and the New.

ERIC Educational Resources Information Center

Trump, J. Lloyd

The design described in this book incorporates experiences of the past eight years in a Model Schools Project that involved at various times 34 junior and senior high schools. It also translates many of the major statements issued by the NASSP as guidelines for improving schools into a workable model. The chapters show how the school develops the…

Production and evaluation of measuring equipment for share viscosity of polymer melts included nanofiller with injection molding machine

NASA Astrophysics Data System (ADS)

Kameda, Takao; Sugino, Naoto; Takei, Satoshi

2016-10-01

Shear viscosity measurement device was produced to evaluate the injection molding workability for high-performance resins. Observation was possible in shear rate from 10 to 10000 [1/sec] that were higher than rotary rheometer by measuring with a plasticization cylinder of the injection molding machine. The result of measurements extrapolated result of a measurement of the rotary rheometer.

Dark-bright soliton pairs in nonlocal nonlinear media.

PubMed

Lin, Yuan Yao; Lee, Ray-Kuang

2007-07-09

We study the formation of dark-bright vector soliton pairs in nonlocal Kerr-type nonlinear medium. We show, by analytical analysis and direct numerical calculation, that in addition to stabilize of vector soliton pairs nonlocal nonlinearity also helps to reduce the threshold power for forming a guided bright soliton. With help of the nonlocality, it is expected that the observation of dark-bright vector soliton pairs in experiments becomes more workable.

Silk Purse from a Sow's Ear? Why Knowledge Matters and Why the Draft History NC Will Not Improve It

ERIC Educational Resources Information Center

Hall, Katie; Counsell, Christine

2013-01-01

Katie Hall and Christine Counsell attempt to construct a Key Stage 3 scheme of work out of the draft National Curriculum for history that was released for consultation in England in February 2013. They explain the process by which they attempted to convert the programme of study into a coherent, workable plan that would fulfil the stated aims.…

3rd Miami international conference on alternative energy sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nejat Veziroglu, T.

1980-01-01

The conference includes sessions on solar energy, ocean thermal energy, wind energy, hydro power, nuclear breeders and nuclear fusion, synthetic fuels from coal or wastes, hydrogen production and uses, formulation of workable policies on energy use and energy conservation, heat and energy storage, and energy education. The volume of the proceedings presents the papers and lectures in condensed format grouped by subject under forty-two sessions for 319 presentations.

Switching-angle sample spinning NMR probe with a commercially available 20 kHz spinning system

NASA Astrophysics Data System (ADS)

Mizuno, Takashi; Takegoshi, K.; Terao, Takehiko

2004-11-01

A switching-angle sample spinning (SASS) probe workable at high spinning speeds was developed using a commercially available rotor/housing system. Details of the construction are described. As application examples of the SASS probe, we report experiments of powder pattern separation at the spinning speed of 20 kHz and broadband 13C- 13C polarization transfer at 16 kHz.

STEM and Teaching German Language and Literature with an Interdisciplinary Approach: 18th-Century Reports by German Jesuit Missionaries in the German Classroom

ERIC Educational Resources Information Center

Classen, Albrecht

2018-01-01

Recent debates about the future of academia have focused primarily on teaching the STEM subjects. This is certainly a valuable call for action, but it also threatens to ignore the significant contributions of the humanities and other fields. This article presents a workable alternative by way of looking at more technical writings by 18th-century…

Remotely Operated Vehicle ROV/AUV Reliability Study. Phase 2.

DTIC Science & Technology

1989-09-01

produce workable configurations for large diameter cyl nders strong enough to survive high compression forces. 11 1.4.5.1.1 Composites Although FWE...Since the main cylinder in manned submersibles is typically large diameter , and the interior is only partially filled with equipment, these systems...ceramics involve control of tolerances when manufacturing large diameter cylinders, although ongoing R&D may provide solutions to this. The major

Applying lessons learned in communities to programs and policies at the federal level.

PubMed

Chang, Debbie I

2006-01-01

As solutions to the problems of the uninsured are debated, there are lessons to be learned from community-based initiatives. Such efforts can provide information on different models as well as key political lessons. Defining the specific role that community efforts play is also critical. Actively involving community stakeholders of such community initiatives in health care policy debates will result in more workable policies.

Math Notebook (From Theory to Practice). Information for Teachers/Parents of Children with Learning Problems in Mathematics. Volumes 5 and 6.

ERIC Educational Resources Information Center

Sharma, Mahesh C., Ed.; Travaglini, Lillian E., Ed.

1988-01-01

Math Notebook is a publication issued 10 times a year, with each issue focusing on a particular learning problem in mathematics and its diagnosis and remediation through practical, workable strategies for use by teaches, parents, and tutors. All the articles were written by Mahesh C. Sharma, with the exception of "The Japanese Soroban," by Frances…

Reliable Video Analysis Helps Security Company Grow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meurer, Dave; Furgal, Dave; Hobson, Rick

Armed Response Team (ART) has grown to become the largest locally owned security company in New Mexico. With technical assistance from Sandia National Laboratories through the New Mexico Small Business Assistance (NMSBA) Program, ART got help so they could quickly bring workable video security solutions to market. By offering a reliable video analytic camera system, they’ve been able to reduce theft, add hundreds of clients, and increase their number of employees.

Aerospace Materials Process Modelling

DTIC Science & Technology

1988-08-01

development of advanced technologies for the fabrication of close-tolerance parts, in conjunction with the development of advanced materials, plays a key...1883. 17. Gegel, H. L., et al., "Materials Modeling and Intrinsic Workability for Simulation of Bulk Deformiti6n," Advanced Technology of Plasticity, Vol...process in the last three decades. As a result of technological advances gained in aerospace industry there has been an increasing demand for the

Study of Fresh and Hardening Process Properties of Gypsum with Three Different PCM Inclusion Methods

PubMed Central

Serrano, Susana; Barreneche, Camila; Navarro, Antonia; Haurie, Laia; Fernandez, A. Inés; Cabeza, Luisa F.

2015-01-01

Gypsum has two important states (fresh and hardened states), and the addition of phase change materials (PCM) can vary the properties of the material. Many authors have extensively studied properties in the hardened state; however, the variation of fresh state properties due to the addition of Micronal® DS 5001 X PCM into gypsum has been the object of few investigations. Properties in fresh state define the workability, setting time, adherence and shrinkage, and, therefore the possibility of implementing the material in building walls. The aim of the study is to analyze, compare and evaluate the variability of fresh state properties after the inclusion of 10% PCM. PCM are added into a common gypsum matrix by three different methods: adding microencapsulated PCM, making a suspension of PCM/water, and incorporating PCM through a vacuum impregnation method. Results demonstrate that the inclusion of PCM change completely the water required by the gypsum to achieve good workability, especially the formulation containing Micronal® DS 5001 X: the water required is higher, the retraction is lower (50% less) due to the organic nature of the PCM with high elasticity and, the adherence is reduced (up to 45%) due to the difference between the porosity of the different surfaces as well as the surface tension difference. PMID:28793584

Waste tyre rubberized concrete: properties at fresh and hardened state.

PubMed

Aiello, M A; Leuzzi, F

2010-01-01

The main objective of this paper is to investigate the properties of various concrete mixtures at fresh and hardened state, obtained by a partial substitution of coarse and fine aggregate with different volume percentages of waste tyres rubber particles, having the same dimensions of the replaced aggregate. Workability, unit weight, compressive and flexural strength and post-cracking behaviour were evaluated and a comparison of the results for the different rubcrete mixtures were proposed in order to define the better mix proportions in terms of mechanical properties of the rubberized concrete. Results showed in this paper were also compared to data reported in literature. Moreover, a preliminary geometrical, physical and mechanical characterization on scrap tyre rubber shreds was made. The rubberized concrete mixtures showed lower unit weight compared to plain concrete and good workability. The results of compressive and flexural tests indicated a larger reduction of mechanical properties of rubcrete when replacing coarse aggregate rather than fine aggregate. On the other hand, the post-cracking behaviour of rubberized concrete was positively affected by the substitution of coarse aggregate with rubber shreds, showing a good energy absorption and ductility indexes in the range observed for fibrous concrete, as suggested by standard (ASTM C1018-97, 1997). 2010 Elsevier Ltd. All rights reserved.

Effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete

NASA Astrophysics Data System (ADS)

Memon, Fareed Ahmed; Nuruddin, Muhd Fadhil; Shafiq, Nasir

2013-02-01

The effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete (SCGC) was investigated in this paper. The work focused on the concrete mixes with a fixed water-to-geopolymer solid (W/Gs) ratio of 0.33 by mass and a constant total binder content of 400 kg/m3. The mass fractions of silica fume that replaced fly ash in this research were 0wt%, 5wt%, 10wt%, and 15wt%. The workability-related fresh properties of SCGC were assessed through slump flow, V-funnel, and L-box test methods. Hardened concrete tests were limited to compressive, splitting tensile and flexural strengths, all of which were measured at the age of 1, 7, and 28 d after 48-h oven curing. The results indicate that the addition of silica fume as a partial replacement of fly ash results in the loss of workability; nevertheless, the mechanical properties of hardened SCGC are significantly improved by incorporating silica fume, especially up to 10wt%. Applying this percentage of silica fume results in 4.3% reduction in the slump flow; however, it increases the compressive strength by 6.9%, tensile strength by 12.8% and flexural strength by 11.5%.

Antibiotics Smart Use: a workable model for promoting the rational use of medicines in Thailand

PubMed Central

Chongtrakul, Pisonthi; Anuwong, Kunyada; Pumtong, Somying; Kongsomboon, Kedsenee; Butdeemee, Parichart; Khonglormyati, Jurairat; Chomyong, Santi; Tongyoung, Parnuchote; Losiriwat, Suraphol; Seesuk, Piyanooch; Suwanwaree, Pongthep; Tangcharoensathien, Viroj

2012-01-01

Abstract The Antibiotics Smart Use (ASU) programme was introduced in Thailand as a model to promote the rational use of medicines, starting with antibiotics. The programme’s first phase consisted of assessing interventions intended to change prescribing practices; the second phase examined the feasibility of programme scale-up. Currently the programme is in its third phase, which centres on sustainability. This paper describes the concept behind ASU, the programme’s functional modalities, the development of its conceptual framework and the implementation of its first and second phases. To change antibiotic prescription practices, multifaceted interventions at the individual and organizational levels were implemented; to maintain behaviour change and scale up the programme, interventions at the network and policy levels were used. The National Health Security Office has adopted ASU as a pay-for-performance criterion, a major achievement that has led to the programme’s expansion nationwide. Despite limited resources, programme scale-up and sustainability have been facilitated by the promotion of local ownership and mutual recognition, which have generated pride and commitment. ASU is clearly a workable entry point for efforts to rationalize the use of medicines in Thailand. Its long-term sustainability will require continued local commitment and political support, effective auditing and integration of ASU into routine systems with appropriate financial incentives. PMID:23284196

Antibiotics Smart Use: a workable model for promoting the rational use of medicines in Thailand.

PubMed

Sumpradit, Nithima; Chongtrakul, Pisonthi; Anuwong, Kunyada; Pumtong, Somying; Kongsomboon, Kedsenee; Butdeemee, Parichart; Khonglormyati, Jurairat; Chomyong, Santi; Tongyoung, Parnuchote; Losiriwat, Suraphol; Seesuk, Piyanooch; Suwanwaree, Pongthep; Tangcharoensathien, Viroj

2012-12-01

The Antibiotics Smart Use (ASU) programme was introduced in Thailand as a model to promote the rational use of medicines, starting with antibiotics. The programme's first phase consisted of assessing interventions intended to change prescribing practices; the second phase examined the feasibility of programme scale-up. Currently the programme is in its third phase, which centres on sustainability. This paper describes the concept behind ASU, the programme's functional modalities, the development of its conceptual framework and the implementation of its first and second phases. To change antibiotic prescription practices, multifaceted interventions at the individual and organizational levels were implemented; to maintain behaviour change and scale up the programme, interventions at the network and policy levels were used. The National Health Security Office has adopted ASU as a pay-for-performance criterion, a major achievement that has led to the programme's expansion nationwide. Despite limited resources, programme scale-up and sustainability have been facilitated by the promotion of local ownership and mutual recognition, which have generated pride and commitment. ASU is clearly a workable entry point for efforts to rationalize the use of medicines in Thailand. Its long-term sustainability will require continued local commitment and political support, effective auditing and integration of ASU into routine systems with appropriate financial incentives.

Test of cold asphalt storability based on alternative approaches

NASA Astrophysics Data System (ADS)

Abaffyová, Zora; Komačka, Jozef

2017-09-01

Cold asphalt products for potholes repairs should be workable (soft enough) for long time to ensure their applicability. Storability is assessed indirectly using various tests of workability. Therefore, simple test methods (self-compaction and disintegration test) was developed and verified to investigate changes of storability of this group of cold asphalts. Selfcompaction of the tested mixture in the upturned Abram’s cone for the cement concrete slump test and in the mould for the California Bearing Ratio test was assessed in first stage. After that the video record of disintegration test was taken. During this test, the mould was lifted up and the mixture fell off the mould (Abram’s cone) or disintegrate (CBR mould). The drop of surface after 10 min self-compaction and netto time related to falling out or disintegration of the mixture were used to evaluate the mixture from storability point of view. It was found out the self-compaction test has not a potential to reveal and prove changes of mixture properties. Based on the disintegration test results it can be stated this test at 5 °C using the upturned Abram’s cone could be a suitable approach to determine qualitative changes of a cold mixture from storability point of view.

Ascendancy of agricultural biotechnology in the Australian political mainstream coexists with technology criticism by a vocal-minority.

PubMed

Tribe, David

2014-07-03

Australia is a federation of States. This political structure necessitates collaborative arrangements between Australian governments to harmonize national regulation of gene technology and food standards. Extensive political negotiation among institutions of federal government has managed regulation of GM crops and food. Well-developed human resources in Australian government provided numerous policy documents facilitating a transparent political process. Workable legislation has been devised in the face of criticisms of gene technology though the political process. Conflicts between potential disruptions to food commodity trade by precautionary proposals for environmental protection were one cause of political tensions, and differences in policy priorities at regional political levels versus national and international forums for negotiation were another. Australian policy outcomes on GM crops reflect (a) strong economic self-interest in innovative and productive farming, (b) reliance on global agricultural market reforms through the Cairns trade group and the WTO, and (c) the importance of Codex Alimentarius and WTO instruments SPS and TBT. Precautionary frameworks for GM food safety assurance that are inconsistent with WTO obligations were avoided in legislation. Since 2008 the 2 major parties, Australian Labor Party (ALP) and the Liberals appear to have reached a workable consensus at the Federal policy level about an important role for agricultural biotechnology in Australia's economic future.

Ascendancy of agricultural biotechnology in the Australian political mainstream coexists with technology criticism by a vocal-minority

PubMed Central

Tribe, David

2014-01-01

Australia is a federation of States. This political structure necessitates collaborative arrangements between Australian governments to harmonize national regulation of gene technology and food standards. Extensive political negotiation among institutions of federal government has managed regulation of GM crops and food. Well-developed human resources in Australian government provided numerous policy documents facilitating a transparent political process. Workable legislation has been devised in the face of criticisms of gene technology though the political process. Conflicts between potential disruptions to food commodity trade by precautionary proposals for environmental protection were one cause of political tensions, and differences in policy priorities at regional political levels versus national and international forums for negotiation were another. Australian policy outcomes on GM crops reflect (a) strong economic self-interest in innovative and productive farming, (b) reliance on global agricultural market reforms through the Cairns trade group and the WTO, and (c) the importance of Codex Alimentarius and WTO instruments SPS and TBT. Precautionary frameworks for GM food safety assurance that are inconsistent with WTO obligations were avoided in legislation. Since 2008 the 2 major parties, Australian Labor Party (ALP) and the Liberals appear to have reached a workable consensus at the Federal policy level about an important role for agricultural biotechnology in Australia's economic future. PMID:25437242

Properties of concrete containing foamed concrete block waste as fine aggregate replacement

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Budiea, A. M. A.; Zaidan, A. L. F.; Rasid, M. H.; Hazimmah, D. S.

2017-11-01

Environmental degradation due to excessive sand mining dumping at certain places and disposal of foamed concrete block waste from lightweight concrete producing industry are issues that should be resolved for a better and cleaner environment of the community. Thus, the main intention of this study is to investigate the potential of foamed concrete block waste as partial sand replacement in concrete production. The foamed concrete waste (FCW) used in this research that were supplied by a local lightweight concrete producing industry. The workability and compressive strength of concrete containing various percentage of foamed concrete waste as partial sand replacement has been investigated. Prior to the use, the foamed concrete waste were crushed to produce finer particles. Six concrete mixes containing various content of crushed foamed concrete waste that are 0%, 10%, 20%, 30%, 40% and 50% were used in this experimental work. Then the prepared specimens were placed in water curing until the testing age. Compressive strength test and flexural strength tests were conducted at 7, 14 and 28 days. The result shows that integration of crushed foamed concrete waste as partial sand replacement in concrete reduces the mix workability. It is interesting to note that both compressive strength and flexural strength of concrete improves when 30% crushed foamed concrete waste is added as partial sand replacement.

Sustainable High Quality Recycling of Aggregates from Waste-to-Energy, Treated in a Wet Bottom Ash Processing Installation, for Use in Concrete Products

PubMed Central

Van den Heede, Philip; Ringoot, Niels; Beirnaert, Arno; Van Brecht, Andres; Van den Brande, Erwin; De Schutter, Geert; De Belie, Nele

2015-01-01

Nowadays, more efforts towards sustainability are required from the concrete industry. Replacing traditional aggregates by recycled bottom ash (BA) from municipal solid waste incineration can contribute to this goal. Until now, only partial replacement has been considered to keep the concrete workability, strength and durability under control. In this research, the feasibility of a full aggregate replacement was investigated for producing prefabricated Lego bricks. It was found that the required compressive strength class for this purpose (C20/25) could be achieved. Nevertheless, a thorough understanding of the BA properties is needed to overcome other issues. As BA is highly absorptive, the concrete’s water demand is high. This workability issue can be dealt with by subjecting the fine BA fraction to a crushing operation to eliminate the porous elements and by pre-wetting the fine and coarse BA fractions in a controlled manner. In addition, a reactive NaOH washing is needed to avoid formation of longitudinal voids and the resulting expansion due to the metallic aluminum present in the BA. Regarding the long-term behavior, heavy metal leaching and freeze-thaw exposure are not problematic, though there is susceptibility to acetic and lactic acid attack and maybe increased sensitivity to alkali-silica reaction. PMID:28787809

Sustainable High Quality Recycling of Aggregates from Waste-to-Energy, Treated in a Wet Bottom Ash Processing Installation, for Use in Concrete Products.

PubMed

Van den Heede, Philip; Ringoot, Niels; Beirnaert, Arno; Van Brecht, Andres; Van den Brande, Erwin; De Schutter, Geert; De Belie, Nele

2015-12-25

Nowadays, more efforts towards sustainability are required from the concrete industry. Replacing traditional aggregates by recycled bottom ash (BA) from municipal solid waste incineration can contribute to this goal. Until now, only partial replacement has been considered to keep the concrete workability, strength and durability under control. In this research, the feasibility of a full aggregate replacement was investigated for producing prefabricated Lego bricks. It was found that the required compressive strength class for this purpose (C20/25) could be achieved. Nevertheless, a thorough understanding of the BA properties is needed to overcome other issues. As BA is highly absorptive, the concrete's water demand is high. This workability issue can be dealt with by subjecting the fine BA fraction to a crushing operation to eliminate the porous elements and by pre-wetting the fine and coarse BA fractions in a controlled manner. In addition, a reactive NaOH washing is needed to avoid formation of longitudinal voids and the resulting expansion due to the metallic aluminum present in the BA. Regarding the long-term behavior, heavy metal leaching and freeze-thaw exposure are not problematic, though there is susceptibility to acetic and lactic acid attack and maybe increased sensitivity to alkali-silica reaction.

Performance characterizations of asphalt binders and mixtures incorporating silane additive ZycoTherm

NASA Astrophysics Data System (ADS)

Hasan, Mohd Rosli Mohd; Hamzah, Meor Othman; Yee, Teh Sek

2017-10-01

Experimental works were conducted to evaluate the properties of asphalt binders and mixtures produced using a relatively new silane additive, named ZycoTherm. In this study, 0.1wt% ZycoTherm was blended with asphalt binder to enable production of asphalt mixture at lower than normal temperatures, as well as improve mix workability and compactability. Asphalt mixture performances towards pavement distresses in tropical climate region were also investigated. The properties of control asphalt binders (60/70 and 80/10 penetration grade) and asphalt binders incorporating 0.1% ZycoTherm were reported based on the penetration, softening point, rotational viscosity, complex modulus and phase angle. Subsequently, to compare the performance of asphalt mixture incorporating ZycoTherm with the control asphalt mixture, cylindrical samples were prepared at recommended temperatures and air voids depending on the binder types and test requirements. The samples were tested for indirect tensile strength (ITS), resilient modulus, dynamic creep, Hamburg wheel tracking and moisture induced damage. From compaction data using the Servopak gyratory compactor, specimen prepared using ZycoTherm exhibit higher workability and compactability compared to the conventional mixture. From the mixture performance test results, mixtures prepared with ZycoTherm showed comparable if not better performance than the control sample in terms of the resistance to moisture damage, permanent deformation and cracking.

Effect of copolymer latexes on physicomechanical properties of mortar containing high volume fly ash as a replacement material of cement.

PubMed

Negim, El-Sayed; Kozhamzharova, Latipa; Gulzhakhan, Yeligbayeva; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

2014-01-01

This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA) as partial replacement of cement in presence of copolymer latexes. Portland cement (PC) was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA) and 2-hydroxymethylacrylate (2-HEMA). Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM). The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final) were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

Effect of Copolymer Latexes on Physicomechanical Properties of Mortar Containing High Volume Fly Ash as a Replacement Material of Cement

PubMed Central

Kozhamzharova, Latipa; Gulzhakhan, Yeligbayeva; Bekbayeva, Lyazzat; Williams, Craig

2014-01-01

This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA) as partial replacement of cement in presence of copolymer latexes. Portland cement (PC) was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA) and 2-hydroxymethylacrylate (2-HEMA). Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM). The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final) were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes. PMID:25254256

[Study on extraction process of Radix Bupleuri].

PubMed

Zhao, Lei; Liu, Benliang; Wu, Fuxiang; Tao, Lanping; Liu, Jian

2004-10-01

The orthogonal design was used to optimize extraction process of Radix Bupleuri with content of total saponin and yield of the extract as markers. Factors that have been chosen were ethanol concentration, ethanol consumption, extraction times and extraction time. Each factor had three levels. The result showed that the optimum extraction condition was 80% ethanol, 4 times the amount of material, refluxing for 4 times, 60 minutes each time. The optimized process was stable and workable.

Our Greatest Natural Resource: Investing in the Future of Alaska's Children. A Report of the Governor's Interim Commission on Children and Youth.

ERIC Educational Resources Information Center

Alaska Office of the Governor, Juneau.

In 1987, the Governor of Alaska's Interim Commission on Children and Youth was given two tasks: (1) to develop a plan for a first-class child care system for working parents statewide that is workable, fair and sensibly integrates with the public schools; and (2) to produce a comprehensive plan to combat the problems facing Alaskans so they are…

Clinical leadership: the elephant in the room.

PubMed

Edmonstone, John

2009-01-01

The article explores the concept of clinical leadership in the National Health Service in the UK by seeking to establish a workable definition and by contrasting it with managerial leadership, focussing on the 'disconnected hierarchy' in professional organizations. It proposes that the problems faced by clinical leadership relate to the current nature of general management in the NHS and concludes by suggesting that clinical leadership is the 'elephant in the room'-often ignored or unaddressed.

Molecular Probes in Marine Ecology: Concepts, Techniques and Applications.

DTIC Science & Technology

1991-08-16

AD-A240 938 FINAL TECNCAL REPORT Title: Molecular Probes In Marine Ecology: Concepts, Techniques and Applications Office of Naval Research Program ...Contact: Leslie D. Garrick, Office of Sponsored Programs (508) 548-3705, ext. 218 Date: August 16, 1991 91-11818 DISCLAIMER NOTICE THIS DOCUMENT IS BEST...disguise, embi-aces the many questions and seeks workable solutions. The 1990 MBL marine ecology course, entered into its second year of a program in

Environmental Early Warning Systems (EEWS): Equation Writer’s Manual.

DTIC Science & Technology

1986-07-01

Flowchart 17 2-3 Preliminary Equation Form in Non-EEWS Format 20 2-4 Completed EEWS Form for a Coastal Zone Consideration 21 2-5 Data Ready to Be Loaded 24...Area into workable Subtopics. 4. Formulate flowcharts to separate and show interrelationships between Subtopic Areas and their desired outputs. 5...Army demand criteria (Army background). 9. Refine flowcharts for each specific Subtopic Area and estimate difficulty of accomplishing each step (Figure

REVIEW OF "CONCEPTUAL MODELS IN TEACHER EDUCATION," BY JOHN R. VERDUIN, WASHINGTON, D.C., AMERICAN ASSOCIATION FOR COLLEGES OF TEACHER EDUCATION, 1967, PP. 140.

ERIC Educational Resources Information Center

TRAVERS, ROBERT M.W.

THE REVIEWER FAULTS THE AUTHOR FOR "SIMPLE AND UNCRITICAL PRESENTATIONS OF IDEAS" THAT FAIL TO RESULT IN THE PROMISED "WORKABLE DOCUMENT FOR PRACTICING TEACHER EDUCATORS TO USE." THE MATERIAL "SHOWS SO COMPLETE A LACK OF CONCERN FOR SUCH MATTERS AS WHETHER A MODEL HAS OR HAS NOT BEEN DERIVED FROM EMPIRICAL RESEARCH, WHETHER THE MODEL HAS OR HAS…

Via Satellite and Cable. English Summary of the Report of The Swedish Parlimentary Committee on Mass Media, an Inquiry into Cable Expansion and Broadcasting Policy. 1984:65.

ERIC Educational Resources Information Center

Swedish Parliament, Stockholm. Committee on Mass Media.

The Swedish government appointed a parliamentary committee on mass media in 1982 to investigate the mass media structure of the country. The committee was charged with the drafting of workable principles for the further development and utilization of new techniques, e.g., satellites and cable services. This report outlines the main tasks involved…

Reliable Video Analysis Helps Security Company Grow

ScienceCinema

Meurer, Dave; Furgal, Dave; Hobson, Rick

2018-05-11

Armed Response Team (ART) has grown to become the largest locally owned security company in New Mexico. With technical assistance from Sandia National Laboratories through the New Mexico Small Business Assistance (NMSBA) Program, ART got help so they could quickly bring workable video security solutions to market. By offering a reliable video analytic camera system, they’ve been able to reduce theft, add hundreds of clients, and increase their number of employees.

Army Sustainment. Volume 42, Issue 3. May-June 2010

DTIC Science & Technology

2010-06-01

created smart cards, refined the content and layout of routine briefs, and developed a workable battle rhythm for the rotation. Many...of classroom MDMP exercise is their only MDMP experience. (Photo by MAJ Christopher LeCron) MAY–jUNE 2010 17 headquarters’ G/S–4 and LNO, ensuring...CTSSB proceed ing. After organizing the survey data, 10 Centra class- rooms were created in ALMS. These classrooms were designated as the sites for each

Observation unit management of acute decompensated heart failure.

PubMed

Schrock, Jon W; Emerman, Charles L

2009-01-01

Acute decompensated heart failure (ADHF) is a common illness presenting to the emergency department (ED) that is amenable to observation unit (OU) treatment. As the number of baby boomers continues to grow and the incidence of heart failure increases, the financial implications of ADHF treatment will become more prominent. Obtaining institutional support and developing a good working relationship with cardiology colleagues is vital to creating workable ADHF protocols for whichever type of OU an institution decides to use.

Study of enhanced photogalvanic effect of Naphthol Green B in natural sunlight

NASA Astrophysics Data System (ADS)

Koli, Pooran

2015-07-01

The photogalvanic cells based on Naphthol Green B sensitizer-Fructose reductant-Sodium Lauryl Sulphate surfactant has been studied in natural sunlight. The cell has been found workable in natural sunlight with greatly enhanced optimum cell performance. The 1159.2 μW power, 4500 μA short-circuit current, 1070 mV open-circuit potential, 14.49% efficiency and 240 min storage capacity (as half change time) has been observed in optimum cell fabrication conditions.

[Studies on extraction process of Radix Platycodi].

PubMed

Wu, Biyuan; Sun, Jun; Jiang, Hongfang

2002-06-01

The orthogonal design was used to optimize the extraction process of Radix Platycodi with content of total saponin and yield of the extract as markers. Factors that have been chosen were alcohol concentration, alcohol consumption, extraction times and extraction time. Each factor has three levels. The result showed that the optimum extraction condition obtained was 70% alcohol, 3 times the amount of material, refluxing for 5 times, 60 minutes each time, the optimized process was stable and workable.

Electromagnetic density of modes for a finite-size three-dimensional structure.

PubMed

D'Aguanno, Giuseppe; Mattiucci, Nadia; Centini, Marco; Scalora, Michael; Bloemer, Mark J

2004-05-01

The concept of the density of modes has been lacking a precise mathematical definition for a finite-size structure. With the explosive growth in the fabrication of photonic crystals and nanostructures, which are inherently finite in size, a workable definition is imperative. We give a simple and physically intuitive definition of the electromagnetic density of modes based on the Green's function for a generic three-dimensional open cavity filled with a linear, isotropic, dielectric material.

The Generation of Situational Awareness within Autonomous Systems - A Near to Mid term Study - Analysis

DTIC Science & Technology

2006-07-01

mobility in complex terrain, robot system designers are still seeking workable processes for mapbuilding, with enduring problems that either require...human) robot system designers /users can seek to control the consequences of robot actions, deliberate or otherwise. A notable particular application...operators a sufficient feeling of presence; if not, robot system designers will have to provide autonomy to the robot to make up for the gaps in human input

Grout Impregnation of Pre-Placed Recycled Concrete Pavement (RCP) for Rapid Repair of Deteriorated Portland Cement Concrete Airfield Pavement

DTIC Science & Technology

2007-04-01

generation, to reduce the amount of cement required, and to provide additional tensile strength to the concrete. Although there was limited success with...generally less workable and requires more cement due to the increased water requirements. He further states that with the equipment currently...52- Table 9. Results of the Type III Grout Scoping Study Mixture Water Cement Ratio Sand Replicate Compressive Strength MPa (psi) Flow Cone

Corporate objectives and the planning process.

PubMed

White, S

1990-02-01

The embodiment of corporate objectives in a workable planning process enables all employees to develop an identity larger than themselves. This results in a more cohesive body and makes it easier to implement the organization's strategy and mission. The senior executives at University Hospital have a long history with the organization and therefore know it well. Whether the new process makes planning more coordinated and comprehensive will be measured by both the subjective and the objective assessment of these executives.

An Analysis of the Defense Spacecraft Market.

DTIC Science & Technology

1985-12-01

this study suffers from having to obtain most of its data second -hand. Much of the information about the companies in the industry is discerned...argument that pure competition was inadequate as a guide for public policy by citing the theory of the second best, which showed that in the 17 i • 7- J...reliable basis for normative appraisal of actual markets" second , that it is necessary to have explicit criteria of workable competition (128:380). The

Development of Tethered Hsp90 Inhibitors Carrying Radioiodinated Probes to Specifically Discriminate and Kill Malignant Breast Tumor Cells

DTIC Science & Technology

2016-05-01

both active (5) and inactive (12) probes. To obtain a control compound with very similar physical properties but lacking the ability to bind to Hsp90...procedure was developed and then adapted and modified to provide workable protocols for radioiodination. An inactive control molecule was also developed...955-959. 4. Impact. The successful synthesis of both and active and inactive tethered Hsp90 carrying iodine that can be successfully

Psychotherapy of the child with true brain damage.

PubMed

Christ, Adolph E

1978-07-01

Psychotherapy of the child with true brain damage presents special problems and requires special approaches. Those who are cognitively primitive--at the sensorimotor or preoperational stage of development--require a crisis approach; those at the concrete or formal operational stage can be treated with a modified insight-oriented approach. Development of a therapeutic alliance, establishment of workable defense mechanisms, identification and clarification of unalterable cognitive defects and issues of termination unique to this special population are discussed.

Workability of glass reinforced concrete (GRC) with granite and silica sand aggregates

NASA Astrophysics Data System (ADS)

Moceikis, R.; Kičaitė, A.; Keturakis, E.

2017-10-01

Glass fiber reinforced concrete (GRC) opens the door for lightweight and complex shaped innovative construction, adding architectural value to buildings. With panel thickness down to 15 mm, considerable amount of total loads and materials per square meter of facade can be saved, if compared to conventionally used 80 mm thickness outer layer in insulated precast concrete wall elements. Even though GRC is used for over 50 years in such countries as Great Britain, USA and Japan, there are very few examples and little research done in Eastern Europe with this building material. European Commission propagates sustainable design as commitment to energy efficiency, environmental stewardship and conservation. For this reason, GRC plays important role in mowing toward these goals. In this paper, GRC premix recipes including fine granite and silica sands, reinforced with 13mm length alkali resistant glass fibers are investigated. Two CEM I 52,5R cements with different particle sizes were used and severe water dissociation noticed in one of concrete mixes. Cement particle size distribution determined with laser diffraction particle analyser Cilas 1090LD. To determine modulus of rupture (M.O.R.) and limit of proportionality (L.O.P), plates thickness 15 and 20 mm were produced and tested for flexural resistance according to 4-point bending scheme. Concrete workability tests were made according EN 1170-1.

In Situ Synchrotron Radiation X-ray Diffraction Study on Phase and Oxide Growth during a High Temperature Cycle of a NiTi-20 at.% Zr High Temperature Shape Memory Alloy

NASA Astrophysics Data System (ADS)

Carl, Matthew; Van Doren, Brian; Young, Marcus L.

2018-03-01

Ternary additions to binary NiTi shape memory alloys are known to significantly affect the characteristic martensite-to-austenite phase transformation, i.e., decrease or increase transformation temperatures. High temperature shape memory alloys can be created by adding Au, Pt, Pd, Hf, or Zr to binary NiTi in appropriate amounts; however, the majority of these ternary additions are exceedingly expensive, unfortunately making them impractical for most commercial applications. Zr is the exception of the group, but it is often disregarded because of its poor workability and thermal stability. In an effort to find a temperature range that allows for the potential workability of NiTiZr alloys in normal atmosphere environments and to gain understanding as to the cause of failure during processing, a NiTi-20 at.% Zr was subjected to a thermal cycle ranging from RT to 1000 °C with short 15 min holds at select temperatures during both heating and cooling while simultaneously collecting high-energy synchrotron radiation X-ray diffraction measurements. This study provides valuable insight into the kinetics of precipitation and oxide formation and its relationship to processing. In addition, scanning electron microscopy was performed on five samples, each isothermally held to examine precipitation and oxide structure and growth.

In Situ Synchrotron Radiation X-ray Diffraction Study on Phase and Oxide Growth during a High Temperature Cycle of a NiTi-20 at.% Zr High Temperature Shape Memory Alloy

NASA Astrophysics Data System (ADS)

Carl, Matthew; Van Doren, Brian; Young, Marcus L.

2018-02-01

Ternary additions to binary NiTi shape memory alloys are known to significantly affect the characteristic martensite-to-austenite phase transformation, i.e., decrease or increase transformation temperatures. High temperature shape memory alloys can be created by adding Au, Pt, Pd, Hf, or Zr to binary NiTi in appropriate amounts; however, the majority of these ternary additions are exceedingly expensive, unfortunately making them impractical for most commercial applications. Zr is the exception of the group, but it is often disregarded because of its poor workability and thermal stability. In an effort to find a temperature range that allows for the potential workability of NiTiZr alloys in normal atmosphere environments and to gain understanding as to the cause of failure during processing, a NiTi-20 at.% Zr was subjected to a thermal cycle ranging from RT to 1000 °C with short 15 min holds at select temperatures during both heating and cooling while simultaneously collecting high-energy synchrotron radiation X-ray diffraction measurements. This study provides valuable insight into the kinetics of precipitation and oxide formation and its relationship to processing. In addition, scanning electron microscopy was performed on five samples, each isothermally held to examine precipitation and oxide structure and growth.

Low cost fabrication development for oxide dispersion strengthened alloy vanes

NASA Technical Reports Server (NTRS)

Perkins, R. J.; Bailey, P. G.

1978-01-01

Viable processes were developed for secondary working of oxide dispersion strengthened (ODS) alloys to near-net shapes (NNS) for aircraft turbine vanes. These processes were shown capable of producing required microstructure and properties for vane applications. Material cost savings of 40 to 50% are projected for the NNS process over the current procedures which involve machining from rectangular bar. Additional machining cost savings are projected. Of three secondary working processes evaluated, directional forging and plate bending were determined to be viable NNS processes for ODS vanes. Directional forging was deemed most applicable to high pressure turbine (HPT) vanes with their large thickness variations while plate bending was determined to be most cost effective for low pressure turbine (LPT) vanes because of their limited thickness variations. Since the F101 LPT vane was selected for study in this program, development of plate bending was carried through to establishment of a preliminary process. Preparation of ODS alloy plate for bending was found to be a straight forward process using currently available bar stock, providing that the capability for reheating between roll passes is available. Advanced ODS-NiCrAl and ODS-FeCrAl alloys were utilized on this program. Workability of all alloys was adequate for directional forging and plate bending, but only the ODS-FeCrAl had adequate workability for shaped preform extrustion.

Effect of boron waste on the properties of mortar and concrete.

PubMed

Topçu, Iker Bekir; Boga, Ahmet Raif

2010-07-01

Utilization of by-products or waste materials in concrete production are important subjects for sustainable development and industrial ecology concepts. The usages as mineral admixtures or fine aggregates improve the durability properties of concrete and thus increase the economic and environmental advantages for the concrete industry. The effect of clay waste (CW) containing boron on the mechanical properties of concrete was investigated. CW was added in different proportions as cement additive in concrete. The effect of CW on workability and strength of concrete were analysed by fresh and hardened concrete tests. The results obtained were compared with control concrete properties and Turkish standard values. The results showed that the addition of CW had a small effect upon the workability of the concrete but an important effect on the reduction of its strength. It was observed that strength values were quite near to that of control concrete when not more than 10% CW was used in place of cement. In addition to concrete specimens, replacing cement with CW produced mortar specimens, which were investigated for their strength and durability properties. The tests of SO( 4) (2-) and Cl(-) effect as well as freeze-thaw behaviour related to the durability of mortar were performed. Consequently, it can be said that some improvements were obtained in durability properties even if mechanical properties had decreased with increasing CW content.

Supplemental Conceptual Design Study of an Integrated Voice/Data Switching and Multiplexing Technique for an Access Area Exchange

DTIC Science & Technology

1976-11-11

exchange. The basis for this choice was derived from several factors . One was a timing analysis that was made for certain basic time-critical software...randidate 6jrstem designs were developed and _*xamined with respect to L their capability to demonstrate the workability of the basic concept and for factors ...algorithm recuires a bit time completion, while SOF production allows byte timing and the involved = SOF correlation procedure may be perfor-med during

The application of natural science data to land management decision-making

NASA Technical Reports Server (NTRS)

Williams, D. L.; Sharpe, C. P.; Rowe, P. G.

1974-01-01

A natural environmental analysis process which allows the decision maker to know the probable consequences of a decision prior to the act is developed. Emphasis is placed on the fit between the natural environment and the social, economic, and functional attributes of man's communities and the transition from nature in its present state to various forms and intensities of development. Applications of the analysis are examined. It is concluded that the analysis is a workable system for land use management.

Quantifying the benefits to the national economy from secondary applications of NASA technology, executive summary

NASA Technical Reports Server (NTRS)

1976-01-01

The feasibility of systematically quantifying the economic benefits of secondary applications of NASA related R and D was investigated. Based upon the tools of economic theory and econometric analysis, a set of empirical methods was developed and selected applications were made to demonstrate their workability. Analyses of the technological developments related to integrated circuits, cryogenic insulation, gas turbines, and computer programs for structural analysis indicated substantial secondary benefits accruing from NASA's R and D in these areas.

Quantifying the benefits to the national economy from secondary applications of NASA technology

NASA Technical Reports Server (NTRS)

1976-01-01

The feasibility of systematically quantifying the economic benefits of secondary applications of NASA related R and D is investigated. Based upon the tools of economic theory and econometric analysis, it develops a set of empirical methods and makes selected applications to demonstrate their workability. Analyses of the technological developments related to integrated circuits, cryogenic insulation, gas turbines, and computer programs for structural analysis indicated substantial secondary benefits accruing from NASA's R and D in these areas.

DRR is a teenager

NASA Astrophysics Data System (ADS)

Nagy, George

2008-01-01

The fifteenth anniversary of the first SPIE symposium (titled Character Recognition Technologies) on Document Recognition and Retrieval provides an opportunity to examine DRR's contributions to the development of document technologies. Many of the tools taken for granted today, including workable general purpose OCR, large-scale, semi-automatic forms processing, inter-format table conversion, and text mining, followed research presented at this venue. This occasion also affords an opportunity to offer tribute to the conference organizers and proceedings editors and to the coterie of professionals who regularly participate in DRR.

Shedding light on El Farol

NASA Astrophysics Data System (ADS)

Challet, Damien; Marsili, M.; Ottino, Gabriele

2004-02-01

We mathematize El Farol bar problem and transform it into a workable model. We find general conditions on the predictor space under which the convergence of the average attendance to the resource level does not require any intelligence on the side of the agents. Secondly, specializing to a particular ensemble of continuous strategies yields a model similar to the Minority Game. Statistical physics of disordered systems allows us to derive a complete understanding of the complex behavior of this model, on the basis of its phase diagram.

Boiler plant training

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peffley, R.E.

Developing an operator training program depends on each individual power plant's operating characteristics. This paper deals with the development of the existing, workable program used at the Eckert and Erickson Stations - Board of Water and Light, Lansing, Michigan. The Eckert Station is a coal fired complex consisting of 3 to 45 MW, 3 to 80 MW, and 4 process steam boilers. This training program encompasses seven (7) operating classifications administered by a Head Operator. A similar program is employed at a single unit 160 MW Erickson Station, covering three (3) operating classifications.

Recent experience with design and manufacture of cine lenses

NASA Astrophysics Data System (ADS)

Thorpe, Michael D.; Dalzell, Kristen E.

2015-09-01

Modern cine lenses require a high degree of aberration correction over a large and ever expanding image size. At low to medium volume production levels, these highly corrected designs also require a workable tolerance set and compensation scheme for successful manufacture. In this paper we discuss the design and manufacture of cine lenses with reference to current designs both internal and in the patent literature and some experience in design, tolerancing and manufacturing these lenses in medium volume production.

Worldwide Report, Arms Control.

DTIC Science & Technology

1986-02-12

corres- pondent that "the Soviet Union has shown a workable way to rid mankind of the threat of a nuclear disaster . The initiatives set an example for...believe the world can be rid of the threat of nuclear disaster ; the 38 world can be rid of nuclear weapons by the year 2000. For this, all those upon...dangerous. The answer to the question asked by the TASS observer I would give as this: Yes, we believe that the world can be rid of the threat of nuclear

A Study of the Hot Workability of Al-8.5 Wt Pct Mg Alloys for Armor Plate Applications

DTIC Science & Technology

1989-01-01

427°C (500, 600, 700, and 800’F) to determine a suitable deformation temperature for the homogenization study. Later it was learned that a lower...alloys, only occurred above 5200C (.7°). Rater, according to fractographie examinaton, the decrease in e, at higher temperatures and/or higher strain...edge cracks that were several centimeters deep opened up at the drilled thermocouple hole; the remainder of the slab was almost free of edge cracks

Some engineering properties of heavy concrete added silica fume

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akkaş, Ayşe; Başyiğit, Celalettin; Esen, Serap

Many different types of building materials have been used in building construction for years. Heavy concretes can be used as a building material for critical building as it can contain a mixture of many heavy elements. The barite itself for radiation shielding can be used and also in concrete to produce the workable concrete with a maximum density and adequate structural strength. In this study, some engineering properties like compressive strength, elasticity modules and flexure strength of heavy concretes’ added Silica fume have been investigated.

Fatigue and fracture: Overview

NASA Technical Reports Server (NTRS)

Halford, G. R.

1984-01-01

A brief overview of the status of the fatigue and fracture programs is given. The programs involve the development of appropriate analytic material behavior models for cyclic stress-strain-temperature-time/cyclic crack initiation, and cyclic crack propagation. The underlying thrust of these programs is the development and verification of workable engineering methods for the calculation, in advance of service, of the local cyclic stress-strain response at the critical life governing location in hot section compounds, and the resultant crack initiation and crack growth lifetimes.

Slimeware: engineering devices with slime mold.

PubMed

Adamatzky, Andrew

2013-01-01

The plasmodium of the acellular slime mold Physarum polycephalum is a gigantic single cell visible to the unaided eye. The cell shows a rich spectrum of behavioral patterns in response to environmental conditions. In a series of simple experiments we demonstrate how to make computing, sensing, and actuating devices from the slime mold. We show how to program living slime mold machines by configurations of repelling and attracting gradients and demonstrate the workability of the living machines on tasks of computational geometry, logic, and arithmetic.

Low-cost Landsat digital processing system for state and local information systems

NASA Technical Reports Server (NTRS)

Hooper, N. J.; Spann, G. W.; Faust, N. L.; Paludan, C. T. N.

1979-01-01

The paper details a minicomputer-based system which is well within the budget of many state, regional, and local agencies that previously could not afford digital processing capability. In order to achieve this goal a workable small-scale Landsat system is examined to provide low-cost automated processing. It is anticipated that the alternative systems will be based on a single minicomputer, but that the peripherals will vary depending on the capability emphasized in a particular system.

Proceedings of the Annual Symposium on Frequency Control (39th) Held in Philadelphia, Pennsylvania on 29-31 May 1985

DTIC Science & Technology

1985-05-01

distribution, was evaluation of phase shift through best fit of assumed to be the beam response to the microwave theoretical curves and experimental...vibration sidebands o Acceleration as shown in the lower calculated curve . o High-Temperature Exposure o Thermal Vacuum Two of the curves show actual phase ...conclude that the method to measure the phase noise with spectrum estimation is workable, and it has no principle limitation. From the curve it has been

A study of space shuttle energy management, approach and landing analysis

NASA Technical Reports Server (NTRS)

Morth, R.

1973-01-01

The steering system of the space shuttle vehicle is presented for the several hundred miles of flight preceding landing. The guidance scheme is characterized by a spiral turn to dissipate excess potential energy (altitude) prior to a standard straight-in final approach. In addition, the system features pilot oriented control, drag brakes, phugoid damping, and a navigational capacity founded upon an inertial measurement unit and an on-board computer. Analytic formulas are used to calculate, represent, and insure the workability of the system's specifications

An Interactive System of Computer Generated Graphic Displays for Motivating Meaningful Learning of Matrix Operations and Concepts of Matrix Algebra

DTIC Science & Technology

1990-09-01

community’s search for a workable set of standards for school mathematics . In 1989 the National Council of Teachers of Mathematics ( NCTM ) established the...made by the Commission on Standards for School Mathematics to the National Council of Teachers of Mathematics ( NCTM ). Of the 40 students who...Abstract This -s-y evaluated students’ responses to a teaching method designed to involve students and teachers of mathematics in a meaningful learning

A Report on Indian Education: (A) In-Depth Study of Nine Indian Families; (B) Memory and Reasoning in Native Children: An Effort at Improvement Through the Teaching of Cognitive Strategies.

ERIC Educational Resources Information Center

Berger, Allen; And Others

The purpose of this first phase of a 3-phase study was to obtain information to use as a base in developing a workable language arts curriculum. Part A of this report dealt with the techniques and results of in-depth interviews of 9 native families in Canada. Each family engaged in a sorting process to determine categories which were of immediate…

Simulation of salt production process

NASA Astrophysics Data System (ADS)

Muraveva, E. A.

2017-10-01

In this paper an approach to the use of simulation software iThink to simulate the salt production system has been proposed. The dynamic processes of the original system are substituted by processes simulated in the abstract model, but in compliance with the basic rules of the original system, which allows one to accelerate and reduce the cost of the research. As a result, a stable workable simulation model was obtained that can display the rate of the salt exhaustion and many other parameters which are important for business planning.

Continuity and change?: Exploring reactions to a guided self-management intervention in a randomised controlled trial for IBS with reference to prior experience of managing a long term condition

PubMed Central

Rogers, Anne; Lee, Victoria; Kennedy, Anne

2007-01-01

Self-care interventions are promoted as effective strategies for improving the quality of life and health outcomes for individuals with long-term health conditions. Outcome measures used in evaluations using Randomised Controlled Trials (RCTs) are not designed to consider patients' prior management strategies and experience of illness. Yet the experience of illness literature suggests that adjusting to living with chronic illness, together with broader contextual influences, are likely to be relevant to understanding responses to self-management initiatives. Using group and individual interview data we attempt to illuminate the transposition of IBS from a condition unsatisfactorily managed by medicine to one successfully managed within the life worlds of individuals. If routine embedding of complex interventions depends on the accomplishment of integration and workability in patients' everyday lives then the design and evaluation of such interventions should view participation as part of a process of continuity as well as change. Responses to formal self-management can be extended beyond psychological and other quantitatively measured outcomes. A useful addendum to trial outcomes for self-management education is an understanding of change as being inextricably linked to people's previous attempts to, and experience of, managing long-term conditions. We suggest that the benefits of understanding the prior experience of managing illness and contact with health services include the acceptability and workability of complex interventions in patients' everyday lives. PMID:17316438

Modelling the minislump spread of superplasticized PPC paste using RLS with the application of Random Kitchen sink

NASA Astrophysics Data System (ADS)

Sathyan, Dhanya; Anand, K. B.; Jose, Chinnu; Aravind, N. R.

2018-02-01

Super plasticizers(SPs) are added to the concrete to improve its workability with out changing the water cement ratio. Property of fresh concrete is mainly governed by the cement paste which depends on the dispersion of cement particle. Cement dispersive properties of the SP depends up on its dosage and the family. Mini slump spread diameter with different dosages and families of SP is taken as the measure of workability characteristic of cement paste chosen for measuring the rheological properties of cement paste. The main purpose of this study includes measure the dispersive ability of different families of SP by conducting minislump test and model the minislump spread diameter of the super plasticized Portland Pozzolona Cement (PPC)paste using regularized least square (RLS) approach along with the application of Random kitchen sink (RKS) algorithm. For preparing test and training data for the model 287 different mixes were prepared in the laboratory at a water cement ratio of 0.37 using four locally available brand of Portland Pozzolona cement (PPC) and SP belonging to four different families. Water content, cement weight and amount of SP (by considering it as seven separate input based on their family and brand) were the input parameters and mini slump spread diameter was the output parameter for the model. The variation of predicted and measured values of spread diameters were compared and validated. From this study it was observed that, the model could effectively predict the minislump spread of cement paste

Reducing bacterial contamination in an Orthopedic Theatre ventilated by natural ventilation, in a Developing Country.

PubMed

Thomas, Stephanie; Palmer, Rish; Phillipo, Edward; Chipungu, Geoffrey

2016-05-31

All surgical procedures have the potential for infection and some of the main sources are contamination from airborne particles, theatre personnel and the theatre environment.  There is strong evidence that the use of ultra-clean air flow systems in orthopedic operating theatres reduces the incidence of deep sepsis after surgery. In the developing world however, this is often an unrealistic solution. The aim of this study was to establish baseline levels of contamination in a working orthopedic theatre, at the Queen Elizabeth Central Hospital, Blantyre, Malawi. To feedback results to the theatre team, promote infection prevention discussion and work with the team to implement workable and realistic goals to improve the intra-operative environment. Samples were collected from theatre equipment available at the time of surgery, from theatre water and theatre air using passive air sampling techniques. Samples were immediately transferred to the Central Microbiology Laboratory for culture on basic culture media. Bacterial contamination of theatre equipment, intra-operative theatre air and water was detected. Results were discussed with the theatre and infection prevention team who were receptive to feedback with regards to infection prevention strategies and keen to develop simple measures which could be put in place to change practice. In this setting, we suggest that implementing workable and realistic goals such as, establishing baseline rates of bacterial contamination and introduction of strict protocols for asepsis and theatre etiquette, may reduce bacterial contamination rates and subsequent intra-operative infection in the absence of expensive engineering solutions.

Deformation Mechanisms and Formability Window for As-Cast Mg-6Al-2Ca-1Sn-0.3Sr Alloy (MRI 230D)

NASA Astrophysics Data System (ADS)

Suresh, Kalidass; Pitcheswara Rao, Kamineni; Chalasani, Dharmendra; Yellapregada Venkata Rama Krishna, Prasad; Hort, Norbert; Dieringa, Hajo

2018-03-01

The hot deformation characteristics of MRI 230D alloy have been evaluated in the temperature range 260-500 °C and strain rate range 0.0003-10 s-1, on the basis of processing map. The processing map exhibited two domains in the ranges: (1) 300-370 °C and 0.0003-0.001 s-1 and (2) 370-480 °C and 0.0003-0.1 s-1. Dynamic recrystallization occurs in the both domains with basal slip dominating in the first domain along with climb as recovery process and second-order pyramidal slip dominating in the second with the recovery by cross-slip. In Domains (1) and (2), the apparent activation energy values estimated using the kinetic rate equation are 143 and 206 kJ/mole, respectively, the first one being close to that for lattice self-diffusion confirming climb. It is recommended that the alloy is best processed at 450 °C and strain rates less than 0.1 s-1, where non-basal slip and cross-slip occur extensively to impart excellent workability. The alloy exhibits flow instability in the form of adiabatic shear band formation and flow localization at lower temperatures and higher strain rates. Forging of a cup-shaped component was performed under various conditions, and the results validated the predictions of the processing map on the workability domains as well as the instability regimes.

The quest for an accurate accounting of public health expenditures.

PubMed

Atchison, C; Barry, M A; Kanarek, N; Gebbie, K

2000-09-01

This article describes one effort to develop management tools that will help public health administrators and policy makers implement comprehensive public health strategies. It recounts the ongoing development of a methodology through which the Essential Public Health Services can be related to public health budgets, appropriations, and expenditures. Through three pilot projects involving: (1) nine state health agencies, (2) three local health agencies, and (3) all local jurisdictions and the state health agency in one state, a workable methodology for identifying public expenditures for comprehensive public health programming has been identified.

A Boon for Bone Research

NASA Technical Reports Server (NTRS)

1996-01-01

NASA studies for astronaut health in long-term space missions led to the development of the Mechanical Response Tissue Analyzer (MRTA), a research tool for astronaut disuse, osteoporosis and related bone disorders among the general population. Ames Research Center and Stanford University generated a workable device and with Gait Scan, Inc., refined and commercialized it. The MRTA is a portable dsinstrument that measures the bending stiffness of bones using electrically-induced vibration and detects and analyzes the frequencies of the resonating bone. Unlike some other methods, the MRTA uses no radiation and is fast, simple and relatively inexpensive.

Enterprise Cloud Architecture for Chinese Ministry of Railway

NASA Astrophysics Data System (ADS)

Shan, Xumei; Liu, Hefeng

Enterprise like PRC Ministry of Railways (MOR), is facing various challenges ranging from highly distributed computing environment and low legacy system utilization, Cloud Computing is increasingly regarded as one workable solution to address this. This article describes full scale cloud solution with Intel Tashi as virtual machine infrastructure layer, Hadoop HDFS as computing platform, and self developed SaaS interface, gluing virtual machine and HDFS with Xen hypervisor. As a result, on demand computing task application and deployment have been tackled per MOR real working scenarios at the end of article.

Hazardous waste management system--Environmental Protection Agency. Notice of regulatory reform actions; request for comments.

PubMed

1982-12-13

In response to Executive Order 12291 and the President's Task Force on Regulatory Relief, the Environmental Protection Agency is reviewing and reassessing the hazardous waste regulations developed under the Resource Conservation and Recovery Act (RCRA). A variety of activities are underway that will simplify procedures and reduce paperwork, modify existing regulations to make them more workable and cost effective, and control new wastes and new processes. The purpose of this notice is to inform the public of these activities and invite comments on the general approaches being taken.

Performance evaluation of Olympic weightlifters.

PubMed

Garhammer, J

1979-01-01

The comparison of weights lifted by athletes in different bodyweight categories is a continuing problem for the sport of olympic weightlifting. An objective mechanical evaluation procedure was developed using basic ideas from a model proposed by Ranta in 1975. This procedure was based on more realistic assumptions than the original model and considered both vertical and horizontal bar movements. Utilization of data obtained from film of national caliber lifters indicated that the proposed method was workable, and that the evaluative indices ranked lifters in reasonable order relative to other comparative techniques.

Boron and Zirconium from Crucible Refractories in a Complex Heat-Resistant Alloy

NASA Technical Reports Server (NTRS)

Decker, R F; Rowe, John P; Freeman, J W

1958-01-01

In a laboratory study of the factors involved in the influence of induction vacuum melting on 55ni-20cr-15co-4mo-3ti-3al heat resistant alloy, it was found that the major factor was the type of ceramic used as the crucible. The study concluded that trace amounts of boron or zirconium derived from reaction of the melt with the crucible refactories improved creep-rupture properties at 1,600 degrees F. Boron was most effective and, in addition, markedly improved hot-workability.

Top down, bottom up structured programming and program structuring

NASA Technical Reports Server (NTRS)

Hamilton, M.; Zeldin, S.

1972-01-01

New design and programming techniques for shuttle software. Based on previous Apollo experience, recommendations are made to apply top-down structured programming techniques to shuttle software. New software verification techniques for large software systems are recommended. HAL, the higher order language selected for the shuttle flight code, is discussed and found to be adequate for implementing these techniques. Recommendations are made to apply the workable combination of top-down, bottom-up methods in the management of shuttle software. Program structuring is discussed relevant to both programming and management techniques.

Pushing Glass: Engaging Young People in Astronomy Through Amateur Mirror Making Classes

NASA Astrophysics Data System (ADS)

Larsen, K.; Slater, K. H.; Drew, B. J. V.

2008-11-01

One of the activities utilized by amateur astronomers to excite the general public about astronomy is mirror making. This activity requires few basic skills other than patience and perseverance, and the proper instruction. This poster reports on the results of a study of mirror making classes conducted by nine amateur astronomy groups in the Northeast and Mid-Atlantic U.S., including class organizers' reflections on their successes and challenges in recruiting and retaining young men and women through the completion of a workable telescope mirror.

Growth of lead tin telluride crystals in gels

NASA Technical Reports Server (NTRS)

Barber, Patrick G.

1986-01-01

Improved gels and several geometries were investigated for use in growing crystals. The use of lead sulfide test crystals proved workable, but it was impossible to obtain and maintain a sufficiently concentrated telluride ion solution to successfully grow lead telluride crystals. It appears that oxygen in the solution is capable of oxidizing the telluride ion up to tellurium metal. The method may still be successful, but only if precautions are taken to eliminate dissolved oxygen from the gels and aqueous solutions and to maintain a suitable concentration of telluride, Te(2)-(aq.).

A single cell penetration system by ultrasonic driving

NASA Astrophysics Data System (ADS)

Zhou, Zhaoying; Xiao, Mingfei; Yang, Xing; Wu, Ting

2008-12-01

The researches of single cell's control and operation are the hotspots in whole world. Among the various technologies, the transmission of ectogenic genetic materials between cell membrane is very significant. Imitating the Chinese traditional acupuncture therapy, a new ultrasonic resonance driving method, is imported to drive a cell's penetration probe. A set of the single cell penetration system was established to perform this function. This system includes four subsystems: driving part, micromanipulation part, observation and measurement part, and actuation part. Some fish egg experiments indicate that this system is workable and effective.

Network Centric Operations (NCO) Case Study. The British Approach to Low-Intensity Operations: Part 2

DTIC Science & Technology

2007-02-12

Imperial War Museum Sound Archive, Accession No. 16397 (6 January 1996 ) 46 Jackson, p .45 47 Nagl, p .66-7 48 Stubbs, p .71 49 Nagl, p .93 Part II 16...Coogan, The Troubles, (London: Arrow, 1996 ), p .145 Part II 61 of 246 but there really appeared to be nothing in between to provide workable...Psychological Ops Capability Since 1945’, British Army Review, December 1996 , p .5 Part II 62 of 246 weakness caused by the lack of both numbers and

Collaboration between traditional practitioners and primary health care staff in South Africa: developing a workable partnership for community mental health services.

PubMed

Campbell-Hall, Vicky; Petersen, Inge; Bhana, Arvin; Mjadu, Sithembile; Hosegood, Victoria; Flisher, Alan J

2010-09-01

The majority of the black African population in South Africa utilize both traditional and public sector Western systems of healing for mental health care. There is a need to develop models of collaboration that promote a workable relationship between the two healing systems. The aim of this study was to explore perceptions of service users and providers of current interactions between the two systems of care and ways in which collaboration could be improved in the provision of community mental health services. Qualitative individual and focus group interviews were conducted with key health care providers and service users in one typical rural South African health sub-district. The majority of service users held traditional explanatory models of illness and used dual systems of care, with shifting between treatment modalities reportedly causing problems with treatment adherence. Traditional healers expressed a lack of appreciation from Western health care practitioners but were open to training in Western biomedical approaches and establishing a collaborative relationship in the interests of improving patient care. Western biomedically trained practitioners were less interested in such an arrangement. Interventions to acquaint traditional practitioners with Western approaches to the treatment of mental illness, orientation of Western practitioners towards a culture-centred approach to mental health care, as well as the establishment of fora to facilitate the negotiation of respectful collaborative relationships between the two systems of healing are required at district level to promote an equitable collaboration in the interests of improved patient care.

GH/IGF-I Transgene Expression on Muscle Homeostasis

NASA Technical Reports Server (NTRS)

Schwartz, Robert J.

1999-01-01

We propose to test the hypothesis that the growth hormone/ insulin like growth factor-I axis through autocrine/paracrine mechanisms may provide long term muscle homeostasis under conditions of prolonged weightlessness. As a key alternative to hormone replacement therapy, ectopic production of hGH, growth hormone releasing hormone (GHRH), and IGF-I will be studied for its potential on muscle mass impact in transgenic mice under simulated microgravity. Expression of either hGH or IGF-I would provide a chronic source of a growth-promoting protein whose biosynthesis or secretion is shut down in space. Muscle expression of the IGF-I transgene has demonstrated about a 20% increase in hind limb muscle mass over control nontransgenic litter mates. These recent experiments, also establish the utility of hind-limb suspension in mice as a workable model to study atrophy in weight bearing muscles. Thus, transgenic mice will be used in hind-limb suspension models to determine the role of GH/IGF-I on maintenance of muscle mass and whether concentric exercises might act in synergy with hormone treatment. As a means to engineer and ensure long-term protein production that would be workable in humans, gene therapy technology will be used by to monitor muscle mass preservation during hind-limb suspension, after direct intramuscular injection of a genetically engineered muscle-specific vector expressing GHRH. Effects of this gene-based therapy will be assessed in both fast twitch (medial gastrocnemius) and slow twitch muscle (soleus). End-points include muscle size, ultrastructure, fiber type, and contractile function, in normal animals, hind limb suspension, and reambutation.

Should catastrophic risks be included in a regulated competitive health insurance market?

PubMed

van de Ven, W P; Schut, F T

1994-11-01

In 1988 the Dutch government launched a proposal for a national health insurance based on regulated competition. The mandatory benefits package should be offered by competing insurers and should cover both non-catastrophic risks (like hospital care, physician services and drugs) and catastrophic risks (like several forms of expensive long-term care). However, there are two arguments to exclude some of the catastrophic risks from the competitive insurance market, at least during the implementation process of the reforms. Firstly, the prospects for a workable system of risk-adjusted payments to the insurers that should take away the incentives for cream skimming are, at least during the next 5 years, more favorable for the non-catastrophic risks than for the catastrophic risks. Secondly, even if a workable system of risk-adjusted payments can be developed, the problem of quality skimping may be relevant for some of the catastrophic risks, but not for non-catastrophic risks. By 'quality skimping' we mean the reduction of the quality of care to a level which is below the minimum level that is acceptable to society. After 5 years of health care reforms in the Netherlands new insights have resulted in a growing support to confine the implementation of the reforms to the non-catastrophic risks. In drawing (and redrawing) the exact boundaries between different regulatory regimes for catastrophic and non-catastrophic risks, the expected benefits of a cost-effective substitution of care have to be weighted against the potential harm caused by cream skimming and quality skimping.

Third world programs confront adolescent fertility.

PubMed

1978-08-01

Recently, there have been efforts to identify workable youth programs and effective research projects that could deal with the problem of adolescent fertility. Typical objectives identified at various conferences concerned with this problem included the following: 1) focus attention on the adverse medical and socioeconomic efforts of early pregnancy; 2) draw attention to the current dimensions of adolescent fertility and its changing patterns; 3) encourage development of programs; and 4) impress decision makers with the importance of programs for adolescents. These conferences express a sense of urgency in developing programs before teen-age pregnancy reaches epidemic proportions. Most of the projects already underway are still pilot efforts and have an impact on a very small sector of the population. Yet, they are positive steps toward a solution of the rising problems of adolescent fertility and help to identify workable solutions. A few of these projects -- underway in Colombia, Argentina, Chile, Cost Rica, Guatemala and Mexico -- are reviewed. The consensus of all conferences held to date has been that cross-cultural interchanges is crucial to the spread of programs and ideas that can be adapted to local conditions. 2 key recommendations have emerged from a meeting of donor and support agencies held in Washington, D.C. in May: 1) a major conference should take place during the International Year of the Child (1979) that would focus on early sexual activity and fertility and 2) an Adolescent Fertility Council should be appointed. An Adolescent Fertility Council would provide a structure to correlate and stimulate interaction, while recognizing that country and culture specific programs are essential.

Postmortem sperm procurement: a legal perspective.

PubMed

Kahan, S E; Seftel, A D; Resnick, M I

1999-06-01

Postmortem sperm procurement with subsequent artificial insemination has become a technically feasible method for posthumous conception. A variety of legal questions exist involving the rights and relationships of the deceased, his family and his issue. We addressed these questions and designed a workable protocol for postmortem sperm procurement. MEDLINE, WESTLAW and LEXIS medical literature, and case law searches were conducted. United States and international case law, United States (federal and state) statutes, Uniform Law Commissions Acts, and law review commentaries and articles were reviewed. While postmortem sperm procurement is being requested throughout the United States, no standard protocol or procedural guidelines have been established by federal or state statute. Furthermore, the courts have not yet addressed this specific scenario in reported case law. Statutes and case law do address related factual scenarios and issues, including property rights in human bodies, rules governing transplantation of human organs/body parts, rights of parties in in vivo sperm bank donations and responsibilities of parents to the conceptus of artificial insemination. A workable protocol can be established by analyzing case law and statutes addressing factually similar scenarios. Urologists must focus on the express intent of the decedent and limit any postmortem sperm retrieval to the specific requests made by the decedent. Decedent requests should be documented in writing. The decedent must be competent and of majority age. In the absence of decedent expressed affirmative directive calling for sperm retrieval, no other relative or guardian may authorize this retrieval. Issues regarding the legitimacy and inheritance rights of the conceptus will most consistently be addressed when explicitly provided for in the will of the decedent.

Comparative performance of conventional OPC concrete and HPC designed by densified mixture design algorithm

NASA Astrophysics Data System (ADS)

Huynh, Trong-Phuoc; Hwang, Chao-Lung; Yang, Shu-Ti

2017-12-01

This experimental study evaluated the performance of normal ordinary Portland cement (OPC) concrete and high-performance concrete (HPC) that were designed by the conventional method (ACI) and densified mixture design algorithm (DMDA) method, respectively. Engineering properties and durability performance of both the OPC and HPC samples were studied using the tests of workability, compressive strength, water absorption, ultrasonic pulse velocity, and electrical surface resistivity. Test results show that the HPC performed good fresh property and further showed better performance in terms of strength and durability as compared to the OPC.

Toward an integrated computerized patient record.

PubMed

Dole, T R; Luberti, A A

2000-04-01

Developing a comprehensive electronic medical record system to serve ambulatory care providers in a large health care enterprise requires significant time and resources. One approach to achieving this system is to devise a series of short-term, workable solutions until a complete system is designed and implemented. The initial solution introduced a basic (mini) medical record system that provided an automated problem/summary sheet and decentralization of ambulatory-based medical records. The next step was to partner with an information system vendor committed to continued development of the long-term system capable of supporting the health care organization well into the future.

Congenital abnormalities of the osseous spine: a radiological approach.

PubMed

Vanhoenacker, F M; De Schepper, A M; Parizel, P M

2005-01-01

The spine may act as a useful window to the diagnosis of many congenital malformations syndromes and skeletal dysplasias. However, radiological identification of these syndromes remains a difficult task, because there are so many syndromes and dysplasias to remember. Moreover, many spinal abnormalities are non-specific and there is much overlap between different genetic and congenital disorders. Consequently, many radiologists cringe when these topics are discussed. The purpose of this short review is to provide the general radiologist a workable primer for systematic analysis of spinal abnormalities encountered in genetic disorders, which may be helpful in (differential) diagnosis.

Ohio`s Voluntary Action Program: An economic development tool or a subtle environmental loophole?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akinmoladun, T.M.; Lewis, R.A.

In an effort to remediate and reuse abandoned or contaminated industrial properties, the Ohio State legislature passed a law in 1994 that created the Ohio Voluntary Action Program (VAP). VAP consists of a series of incentives for property owners and prospective buyers to accelerate cleanup and reuse of abandoned sites or brownfields. This paper examines the essence of this unconventional approach to socio-economic development and environmental restoration. The weaknesses of the program are discussed, and recommendations are made to make the program more workable, more realistic, and conducive to environmental protection and public health.

Development of a Fiber Laser Welding Capability for the W76, MC4702 Firing Set

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samayoa, Jose

2010-05-12

Development work to implement a new welding system for a Firing Set is presented. The new system is significant because it represents the first use of fiber laser welding technology at the KCP. The work used Six-Sigma tools for weld characterization and to define process performance. Determinations of workable weld parameters and comparison to existing equipment were completed. Replication of existing waveforms was done utilizing an Arbitrary Pulse Generator (APG), which was used to modulate the fiber laser’s exclusive continuous wave (CW) output. Fiber laser weld process capability for a Firing Set is demonstrated.

Empowering battered women transnationally: the case for postmodern interventions.

PubMed

Mills, L

1996-05-01

Violence against women by their intimate partners remains a leading cause of injury and death to women worldwide. Governments around the globe are searching for appropriate solutions to woman abuse. This article examines transnational legal interventions instituted to respond to the problem of intimate violence and assesses the propriety of the criminal model on which they are based. Using postmodern social work theory and practice, the article promotes the idea of a more workable alternative response to the problem--a domestic violence commission that places control over her actions and reactions in the hands of the battered woman.

Elements in the history of the Periodic Table.

PubMed

Rouvray, Dennis H

2004-06-01

Discovery of the Periodic Table was rendered possible only after four decisive prerequisites had been achieved. These were (i) the abandonment of the metaphysical and occult notions of elements that typified the alchemical era; (ii) the adoption of a modern and workable definition of an element; (iii) the development of analytical chemical techniques for the isolation of the elements and determination of their properties; and (iv) the devising of a means of associating each element with a characteristic natural number. The Periodic Table made its appearance on cue almost as soon as these preconditions had been fulfilled.

Arsenic in the groundwater: Occurrence, toxicological activities, and remedies.

PubMed

Jha, S K; Mishra, V K; Damodaran, T; Sharma, D K; Kumar, Parveen

2017-04-03

Arsenic (As) contamination in groundwater has become a geo-environmental as well as a toxicological problem across the globe affecting more than 100-million people in nearly 21 countries with its associated disease "arsenicosis." Arsenic poisoning may lead to fatal skin and internal cancers. In present review, an attempt has been made to generate awareness among the readers about various sources of occurrence of arsenic, its geochemistry and speciation, mobilization, metabolism, genotoxicity, and toxicological exposure on humans. The article also emphasizes the possible remedies for combating the problem. The knowledge of these facts may help to work on some workable remedial measure.

Relativistic bound states in three space-time dimensions in Minkowski space

NASA Astrophysics Data System (ADS)

Gutierrez, C.; Gigante, V.; Frederico, T.; Tomio, Lauro

2016-01-01

With the aim to derive a workable framework for bound states in Minkowski space, we have investigated the Nakanishi perturbative integral representation of the Bethe-Salpeter (BS) amplitude in two-dimensions (2D) in space and time (2+1). The homogeneous BS amplitude, projected onto the light-front plane, is used to derive an equation for the Nakanishi weight function. The formal development is illustrated in detail and applied to the bound system composed by two scalar particles interacting through the exchange of a massive scalar. The explicit forms of the integral equations are obtained in ladder approximation.

Testing the limits of the 'joint account' model of genetic information: a legal thought experiment.

PubMed

Foster, Charles; Herring, Jonathan; Boyd, Magnus

2015-05-01

We examine the likely reception in the courtroom of the 'joint account' model of genetic confidentiality. We conclude that the model, as modified by Gilbar and others, is workable and reflects, better than more conventional legal approaches, both the biological and psychological realities and the obligations owed under Articles 8 and 10 of the European Convention on Human Rights (ECHR). Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The Redox Flow System for solar photovoltaic energy storage

NASA Technical Reports Server (NTRS)

Odonnell, P.; Gahn, R. F.; Pfeiffer, W.

1976-01-01

The interfacing of a Solar Photovoltaic System and a Redox Flow System for storage was workable. The Redox Flow System, which utilizes the oxidation-reduction capability of two redox couples, in this case iron and titanium, for its storage capacity, gave a relatively constant output regardless of solar activity so that a load could be run continually day and night utilizing the sun's energy. One portion of the system was connected to a bank of solar cells to electrochemically charge the solutions, while a separate part of the system was used to electrochemically discharge the stored energy.

Optical calculation of correlation filters for a robotic vision system

NASA Technical Reports Server (NTRS)

Knopp, Jerome

1989-01-01

A method is presented for designing optical correlation filters based on measuring three intensity patterns: the Fourier transform of a filter object, a reference wave and the interference pattern produced by the sum of the object transform and the reference. The method can produce a filter that is well matched to both the object, its transforming optical system and the spatial light modulator used in the correlator input plane. A computer simulation was presented to demonstrate the approach for the special case of a conventional binary phase-only filter. The simulation produced a workable filter with a sharp correlation peak.

Marketing your expertise.

PubMed

Czaplewski, L M

1999-01-01

Marketing an existing or new venture is a vital part of business. For the nurse entrepreneur, marketing involves applying previously learned skills to new situations. The methods used to market a service may mean the difference between success and failure. Unfortunately many entrepreneurs think that because they have a great idea, clients will beat a path to their door. Marketing requires planning, creativity, time, and money. It is an ongoing process that must be evaluated regularly. When marketing achieves results, clients commit to using the entrepreneur's services and profits are realized. Basic marketing concepts are considered, and strategies for developing a workable marketing plan are presented.

Study of Carbide Evolution During Thermo-Mechanical Processing of AISI D2 Tool Steel

NASA Astrophysics Data System (ADS)

Bombac, D.; Fazarinc, M.; Podder, A. Saha; Kugler, G.

2013-03-01

The microstructure of a cold-worked tool steel (AISI D2) with various thermo-mechanical treatments was examined in the current study to identify the effects of these treatments on phases. X-ray diffraction was used to identify phases. Microstructural changes such as spheroidization and coarsening of carbides were studied. Thermodynamic calculations were used to verify the results of the differential thermal analysis. It was found that soaking temperature and time have a large influence on dissolution, precipitation, spheroidization, and coalescence of carbides present in the steel. This consequently influences the hot workability and final properties.

Uniting geology and craftsmanship to find the optimal soapstone for restoration of the Nidaros soapstone Cathedral in Norway

NASA Astrophysics Data System (ADS)

Aslaksen Aasly, Kari; Meyer, Gurli Birgitte; Kløve Keiding, Jakob; Langås, Rune; Lund, Vegard

2017-04-01

The Nidaros Cathedral situated in Trondheim, Norway is a restored cathedral resting on the remnants of an original medieval church sanctified St Olav. The cathedral became one of the most important sanctuary for pilgrimage during the Middle Ages and still is today. In a European context the cathedral, along with a certain group of other churches and monasteries in Norway, is unique by being build from soapstone (steatite). This talc and chlorite dominated metamorphic rock is relatively soft, heat resistant and dense making the material ideal for cooking pots, stoves and all kinds of utensils. Soapstone has therefore been appreciated, used and quarried since the Stone Age in Norway. At the onset of Christianity the choice of soapstone from harder rock types was not difficult for the building owners combining the vision of stone churches in Norway with the skills of wood carving traditions of local handicraftsmen. The best example is the Nidaros Cathedral built in the 11th to 14th century. In 1869, the Nidaros Cathedral Restoration Workshop (NDR) was founded with the purpose of restoring the cathedral using original craftsman's techniques and authentic materials. The restoration was originally completed in 1969, but is still ongoing due to weathering of certain used soapstone types. A major challenge remains to find soapstone resources of the right quality. Core issues relate to avoid rocks with cracks and cleavage, a demand for homogeneity, maintaining esthetic authenticity, resistance to weathering (disintegration) and last but not least the ultimatum of workability. Thus locating new soapstone resources depends strongly on geological understanding, quarry experience and stone carver's knowledge. The present work is based on close cooperation between stone carvers and geologists in a common goal of uniting knowledge and experience in defining qualities of soapstone for various purposes of restoration. Cooperate observations of geology and carving properties in the very same spots has been performed during fieldwork, through studies of drill cores and during carving in the workshop of NDR. Through careful geological translation of terms and experience from the stone carvers, a series of stone properties have been outlined. Supplementary studies of alteration and damages to stone has added significantly to the present bank of knowledge. The internal qualities of a soapstone has subsequently been described in terms of the geological processes forming it and the cycles of deformation altering it. The most important conclusion from this work is, that most deposits holds contradictions between workability and durability. The workability calls for soft minerals while the durability is dependent on weathering resistant and hard minerals. Only a narrow window exists in which the softness is united with resistance to alteration.

Barriers to Advance Care Planning at the End of Life: An Explanatory Systematic Review of Implementation Studies

PubMed Central

Lund, Susi; Richardson, Alison; May, Carl

2015-01-01

Context Advance Care Plans (ACPs) enable patients to discuss and negotiate their preferences for the future including treatment options at the end of life. Their implementation poses significant challenges. Objective To investigate barriers and facilitators to the implementation of ACPs, focusing on their workability and integration in clinical practice. Design An explanatory systematic review of qualitative implementation studies. Data sources Empirical studies that reported interventions designed to support ACP in healthcare. Web of Knowledge, Ovid MEDLINE, CINAHL, PsycINFO, British Nursing Index and PubMed databases were searched. Methods Direct content analysis, using Normalization Process Theory, to identify and characterise relevant components of implementation processes. Results 13 papers identified from 166 abstracts were included in the review. Key factors facilitating implementation were: specially prepared staff utilizing a structured approach to interactions around ACPs. Barriers to implementation were competing demands of other work, the emotional and interactional nature of patient-professional interactions around ACPs, problems in sharing decisions and preferences within and between healthcare organizations. Conclusions This review demonstrates that doing more of the things that facilitate delivery of ACPs will not reduce the effects of those things that undermine them. Structured tools are only likely to be partially effective and the creation of a specialist cadre of ACP facilitators is unlikely to be a sustainable solution. The findings underscore both the challenge and need to find ways to routinely incorporate ACPs in clinical settings where multiple and competing demands impact on practice. Interventions most likely to meet with success are those that make elements of Advance Care Planning workable within complex and time pressured clinical workflows. PMID:25679395

Assessing manual dexterity: Comparing the WorkAbility Rate of Manipulation Test with the Minnesota Manual Dexterity Test.

PubMed

Wang, Ying-Chih; Wickstrom, Rick; Yen, Sheng-Che; Kapellusch, Jay; Grogan, Kimberly A

2017-05-10

Cross-sectional study. The WorkAbility Rate of Manipulation Test (WRMT), an adaptation of the Minnesota Manual Dexterity Test (MMDT), contains a revised board and protocols to improve its utility for therapy or fitness assessment. To describe the development and preliminary psychometric properties of WRMT. Sixty-six healthy participants completed MMDT and WRMT in a random order followed by a user experience survey. We compared tests using repeated-measures analysis of variance, test-retest reliability, and examined agreement between tests. Despite the similarities of these 2 instruments, the different administration protocols resulted in statistically different score distributions (P < .001). Results supported good test-retest reliability of WRMT (placing test ICC = 0.88-0.90 and turning test ICC = 0.68-0.82). The WRMT correlated moderately with MMDT (r = 0.81 in placing test and r = 0.44-0.57 in turning test). Bland-Altman plot showed that the differences in completion time were 3.8 seconds between placing tests and 19.6 (both hands), 0.3 (right hand), and 3.9 (left hand) seconds between turning tests. Overall, participants felt that the instruction of WRMT was easier to follow (44%) and preferred its setup, color, and depth of the test board (49%). Time required to complete 1 panel of 20 disks correlated highly with the time needed to finish a complete trial of 60 disks in both MMDT (r = 0.91-0.97) and WRMT (r = 0.88-0.95). Caution is warranted in comparing scores from these 2 test variants. 3b. Copyright © 2017 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Sense and Sensibility: The Case for the Nationwide Inclusion of Engineering in the K-12 Curriculum

NASA Technical Reports Server (NTRS)

Lindberg, Robert E.; Pinelli, Thomas E.; Batterson, James G.

2008-01-01

The competitive status of the United States is inextricably linked to innovation just as innovation is inseparable from science, technology, engineering, and mathematics. To stay competitive in innovation requires that the United States produce a 21st century workforce complete with requisite education, training, skills, and motivation. If we accept a priori that science, technology, engineering, and mathematics education are crucial to competitiveness and innovation and that, in terms of innovation, mathematics, science, and engineering are interdependent, why are mathematics and science uniformly ubiquitous in the K-12 curriculum while engineering is conspicuously absent? We are passionate in our belief that the uniform addition of engineering to the K-12 curriculum will help ensure that the nation has "the right" 21st Century workforce. Furthermore, we believe that a nationwide effort, led by a coalition of engineering academics, practitioners, and societies is required to turn this goal into reality. However, accomplishing this goal necessitates, as we are reminded by the title of Jane Austen's timeless novel, "Sense and Sensibility", a workable solution that seeks the "middle ground" between passion and reason. We begin our paper by making two essential points: Engineers are not scientists. Engineering exists separate from science, has its own specialized knowledge community apart from science, and it is largely responsible for many of the most significant advancements and improvements in the quality of our life. Our workable solution requires that K-12 education, nationwide, accommodate the inclusion of engineering as a stand alone curriculum and we offer three reasons to support our position: (1) workforce development, (2) stimulating interest in STEM (science, technology, engineering, and mathematics) courses and careers, and (3) creating a technologically literate society. We conclude with some thoughts on how this important goal can be accomplished.

Effect of Rice Husk Ash and Fly Ash on the workability of concrete mixture in the High-Rise Construction

NASA Astrophysics Data System (ADS)

Van Tang, Lam; Bulgakov, Boris; Bazhenova, Sofia; Aleksandrova, Olga; Pham, Anh Ngoc; Dinh Vu, Tho

2018-03-01

The dense development of high-rise construction in urban areas requires a creation of new concretes with essential properties and innovative technologies for preparing concrete mixtures. Besides, it is necessary to develop new ways of presenting concrete mixture and keeping their mobility. This research uses the mathematical method of two-factors rotatable central compositional planning to imitate the effect of amount of rice husk (RHA) and fly ash of thermal power plants (FA) on the workability of high-mobility concrete mixtures. The results of this study displays regression equation of the second order dependence of the objective functions - slump cone and loss of concrete mixture mobility due to the input factors - the amounts RHA (x1) and FA (x2), as well as the surface expression image of these regression equations. An analysis of the regression equations also shows that the amount of RHA and FA had a significant influence on the concrete mixtures mobility. In fact, the particles of RHA and FA will play the role as peculiar "sliding bearings" between the grains of cement leading to the dispersion of cement in the concrete mixture. Therefore, it is possible to regulate the concrete mixture mobility when transporting fresh concrete to the formwork during the high-rise buildings construction in the hot and humid climate of Vietnam. Although the average value of slump test of freshly mixed concrete, measured 60 minutes later after the mixing completion, decreased from 18.2 to 10.52 cm, this value still remained within the allowable range to maintain the mixing and and the delivery of concrete mixture by pumping.

Genipin diffusion and reaction into a gelatin matrix for tissue engineering applications.

PubMed

Montemurro, Francesca; De Maria, Carmelo; Orsi, Gianni; Ghezzi, Lisa; Tinè, Maria Rosaria; Vozzi, Giovanni

2017-04-01

Genipin is a natural low-toxic cross-linker for molecules with primary amino groups, and its use with collagen and gelatin has shown a great potential in tissue engineering applications. The fabrication of scaffolds with a well-organized micro and macro topology using additive manufacturing systems requires an accurate control of working parameters, such as reaction rate, gelling time, and diffusion constant. A polymeric system of 5% w/v gelatin in PBS with 2 mg/mL collagen solutions in a 1:1 weight ratio was used as template to perform measurements varying genipin concentration in a range of 0.1-1.5% w/w with respect to gelatin. In the first part of this work, the reaction rate of the polymeric system was estimated using a new colorimetric analysis of the reaction. Then its workability time, closely related to the gelling time, was evaluated thanks to rheological analysis: finally, the quantification of static and dynamic diffusion constants of genipin across nonreacting and reacting membranes, made respectively by agarose and gelatin, was performed. It was shown that the colorimetric analysis is a good indicator of the reaction progress. The gelling time depends on the genipin concentration, but a workability window of 40 min guaranteed up to 0.5% w/w genipin. The dynamic diffusion constant of genipin in the proposed polymeric system is in the order of magnitude of 10 -7 . The obtained results indicated the possibility to use the genipin, gelatin, and collagen, in the proposed concentrations, to build well-defined hydrogel scaffolds with both extrusion-based and 3D ink-jet system. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 473-480, 2017. © 2015 Wiley Periodicals, Inc.

What work has to be done to implement collaborative care for depression? Process evaluation of a trial utilizing the Normalization Process Model

PubMed Central

2010-01-01

Background There is a considerable evidence base for 'collaborative care' as a method to improve quality of care for depression, but an acknowledged gap between efficacy and implementation. This study utilises the Normalisation Process Model (NPM) to inform the process of implementation of collaborative care in both a future full-scale trial, and the wider health economy. Methods Application of the NPM to qualitative data collected in both focus groups and one-to-one interviews before and after an exploratory randomised controlled trial of a collaborative model of care for depression. Results Findings are presented as they relate to the four factors of the NPM (interactional workability, relational integration, skill-set workability, and contextual integration) and a number of necessary tasks are identified. Using the model, it was possible to observe that predictions about necessary work to implement collaborative care that could be made from analysis of the pre-trial data relating to the four different factors of the NPM were indeed borne out in the post-trial data. However, additional insights were gained from the post-trial interview participants who, unlike those interviewed before the trial, had direct experience of a novel intervention. The professional freedom enjoyed by more senior mental health workers may work both for and against normalisation of collaborative care as those who wish to adopt new ways of working have the freedom to change their practice but are not obliged to do so. Conclusions The NPM provides a useful structure for both guiding and analysing the process by which an intervention is optimized for testing in a larger scale trial or for subsequent full-scale implementation. PMID:20181163

Application of P.O and R-SAC mortar for 3D printing in construction

NASA Astrophysics Data System (ADS)

Lin, J. C.; Wu, X.; Yang, W.; Zhao, R. X.; Qiao, L. G.

2018-01-01

Compared with traditional properties of building materials, 3D printing materials should have controllable setting time, appropriate workability and superior mechanical properties. Adaptability of two types of cementitious system on the 3D printing were investigated in this paper. Results showed that both of them can match of 3D printing process with the working window time required (10-90min) by using the compound adjustable solidification agents, which have the high mechanical properties (3d⩾30MPa, 28d> 63MPa), and appropriate suitable parameter range of fluidity (R-SAC:210-240mm,P.O:200-220mm).

Photovoltaics module interface: General purpose primers

NASA Technical Reports Server (NTRS)

Boerio, J.

1985-01-01

The interfacial chemistry established between ethylene vinyl acetate (EVA) and the aluminized back surface of commercial solar cells was observed experimentally. The technique employed is called Fourier Transform Infrared (FTIR) spectroscopy, with the infrared signal being reflected back from the aluminum surface through the EVA film. Reflection infrared (IR) spectra are given and attention is drawn to the specific IR peak at 1080/cm which forms on hydrolytic aging of the EVA/aluminum system. With this fundamental finding, and the workable experimental techniques, candidate silane coupling agents are employed at the interface, and their effects on eliminating or slowing hydrolytic aging of the EVA/aluminum interface are monitored.

Interactive specification acquisition via scenarios: A proposal

NASA Technical Reports Server (NTRS)

Hall, Robert J.

1992-01-01

Some reactive systems are most naturally specified by giving large collections of behavior scenarios. These collections not only specify the behavior of the system, but also provide good test suites for validating the implemented system. Due to the complexity of the systems and the number of scenarios, however, it appears that automated assistance is necessary to make this software development process workable. Interactive Specification Acquisition Tool (ISAT) is a proposed interactive system for supporting the acquisition and maintenance of a formal system specification from scenarios, as well as automatic synthesis of control code and automated test generation. This paper discusses the background, motivation, proposed functions, and implementation status of ISAT.

How to run a successful Journal

PubMed Central

Jawaid, Shaukat Ali; Jawaid, Masood

2017-01-01

Publishing and successfully running a good quality peer reviewed biomedical scientific journal is not an easy task. Some of the pre-requisites include a competent experienced editor supported by a team. Long term sustainability of a journal will depend on good quality manuscripts, active editorial board, good quality of reviewers, workable business model to ensure financial support, increased visibility which will ensure increased submissions, indexation in various important databases, online availability and easy to use website. This manuscript outlines the logistics and technical issues which need to be resolved before starting a new journal and ensuring sustainability of a good quality peer reviewed journal. PMID:29492089

Invisible players: a family systems model.

PubMed

Hellstedt, Jon

2005-10-01

This article attempts to demonstrate that the family is a key player in the athlete's development and performance, sometimes invisible, but often all too visible. The practice of clinical sport psychology is enriched by a family-based orientation to the assessment and treatment of athletes. Creating a workable family system is a challenge for parents. They have many difficult decisions to make, and are often without support and direction in making those choices. Sport psychiatrists and psychologists can be helpful to parents as well as athletes by using family-based assessments and treatment interventions that provide education, challenge, and support as they negotiate the tasks and transitions in the family life cycle.

Design fabrication and nondestructive testing of six experimental AGCarb/Intermold 3 cylinder assemblies

NASA Technical Reports Server (NTRS)

Thacher, E. F.

1972-01-01

Six subscale Intermold cylinder assemblies with a total of twelve different concepts for transition to AGCarb were fabricated. Three of the cylinder assemblies were made by helically winding the hoop fibers and three were of orthogonal configuration. The fabrication process is summarized and details of each manufacturing method are given. The objectives of the test program were to: (1) demonstrate the fabricability of the Intermold 3 subscale flanges, (2) produce an integral transition from Intermold 3 to AGCarb material, (3) define a workable manufacturing process, and (4) identify a best suited inspection method. The objectives were met and the results are described.

Ultrafine cementitious grout

DOEpatents

Ahrens, Ernst H.

1999-01-01

An ultrafine cementitious grout in three particle grades containing Portland cement, pumice as a pozzolanic material and superplasticizer in the amounts of about 30 wt. % to about 70 wt. % Portland cement; from about 30 wt. % to about 70 wt. % pumice containing at least 70% amorphous silicon dioxide; and from 1.2 wt. % to about 5.0 wt. % superplasticizer. The superplasticizer is dispersed in the mixing water prior to the addition of dry grout and the W/CM ratio is about 0.4 to 1/1. The grout has very high strength and very low permeability with good workability. The ultrafine particle sizes allow for sealing of microfractures below 10 .mu.m in width.

Sowing the Seeds: Reproduction and Educational Reform in China. Essay Review [of "Power in Education: The Case of Miao University Students and Its Significance for American Culture" (Henry T. Trueba, Yali Zou); "Radicalism and Education Reform in 20th-Century China: The Search for an Ideal Development Model" (Suzanne Pepper); and "Teacher Education in the People's Republic of China" (Rhea A. Ashmore, Zhen Cao)].

ERIC Educational Resources Information Center

Liu, Judith; Kelly, Donald P.

1998-01-01

Three recent books that deal with China's continuing quest to create a workable educational system address the evolution of teacher education, the position of ethnic minority groups in higher education, and the historical social consequences of educational policies. Taken together, the works indicate the institutionalization of Western-style…

An Output Approach to Incentive Reimbursement for Hospitals

PubMed Central

Ro, Kong-kyun; Auster, Richard

1969-01-01

A method of incentive reimbursement for health care institutions is described that is designed to stimulate the providers' efficiency. The two main features are: (1) reimbursement based on a weighted average of actual cost and mean cost plus or minus an appropriate number of standard deviations; (2) output defined as episodes of illness given adequate treatment instead of days of hospitalization. It is suggested that despite the operational difficulties involved in a method of payment based on an output approach, the flexibility incorporated into the determination of reimbursement by use of the properties of a normal frequency distribution would make the system workable. PMID:5349002

Study of Fuze Structure and Reliability Design Based on the Direct Search Method

NASA Astrophysics Data System (ADS)

Lin, Zhang; Ning, Wang

2017-03-01

Redundant design is one of the important methods to improve the reliability of the system, but mutual coupling of multiple factors is often involved in the design. In my study, Direct Search Method is introduced into the optimum redundancy configuration for design optimization, in which, the reliability, cost, structural weight and other factors can be taken into account simultaneously, and the redundant allocation and reliability design of aircraft critical system are computed. The results show that this method is convenient and workable, and applicable to the redundancy configurations and optimization of various designs upon appropriate modifications. And this method has a good practical value.

Ab initio calculation of one-nucleon halo states

NASA Astrophysics Data System (ADS)

Rodkin, D. M.; Tchuvil'sky, Yu M.

2018-02-01

We develop an approach to microscopic and ab initio description of clustered systems, states with halo nucleon and one-nucleon resonances. For these purposes a basis combining ordinary shell-model components and cluster-channel terms is built up. The transformation of clustered wave functions to the uniform Slater-determinant type is performed using the concept of cluster coefficients. The resulting basis of orthonormalized wave functions is used for calculating the eigenvalues and the eigenvectors of Hamiltonians built in the framework of ab initio approaches. Calculations of resonance and halo states of 5He, 9Be and 9B nuclei demonstrate that the approach is workable and labor-saving.

Towards an electro-magnetic field separation of deposited material implemented in an ion beam sputter process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malobabic, Sina; Jupe, Marco; Ristau, Detlev

Nowadays, Ion Beam Sputter (IBS) processes are very well optimized on an empirical basis. To achieve further progresses, a modification of the IBS process by guiding the coating material using an axial magnetic field and an additional electrical field has been studied. The electro-magnetic (EM) field leads to a significant change in plasma properties and deposition rate distributions, whereas an increase in deposition rate along the centerline of the axial EM field around 150% was observed. These fundamental studies on the prototype are the basis for the development of an applicable and workable design of a separation device.

More inclusive workplaces: fact or fiction? The case of Norway.

PubMed

Olsen, T; Svendal, A; Amundsen, I

2005-10-01

Over the past years focus on different workfare programmes in Norway has increased in order to meet a number of identified problems in the labour market. The Tripartite Agreement on a More Inclusive Workplace of October 2001 is one of the measures introduced to create a more inclusive workplace, reduce the utilization of disability benefits and sick leave, and retain senior employees longer. Recommended methodology is improved employee-employer dialogue and increased focus on what the employee can do (workability). This paper is a critical review of why the Agreement has, so far, not lived up to the expectations. We also question whether the logic of the Tripartite Agreement is the solution to the problem.

Calculation of free turbulent mixing by interaction approach.

NASA Technical Reports Server (NTRS)

Morel, T.; Torda, T. P.

1973-01-01

The applicability of Bradshaw's interaction hypothesis to two-dimensional free shear flows was investigated. According to it, flows with velocity extrema may be considered to consist of several interacting layers. The hypothesis leads to a new expression for the shear stress which removes the usual restriction that shear stress vanishes at the velocity extremum. The approach is based on kinetic energy and the length scale equations. The compressible flow equations are simplified by restriction to low Mach numbers, and the range of their applicability is discussed. The empirical functions of the turbulence model are found here to be correlated with the spreading rate of the shear layer. The analysis demonstrates that the interaction hypothesis is a workable concept.

Theoretical study of production of unique glasses in space

NASA Technical Reports Server (NTRS)

Larsen, D. C.

1974-01-01

Analytical functional relationships describing homogeneous nucleation and crystallization in various supercooled liquids were developed. The time and temperature dependent relationships of nucleation and crystallization (intrinsic properties) are being used to relate glass forming tendency to extrinsic parameters such as cooling rate through computer simulation. Single oxide systems are being studied initially to aid in developing workable kinetic models and to indicate the primary materials parameters affecting glass formation. The theory and analytical expressions developed for simple systems is then extended to complex oxide systems. A thorough understanding of nucleation and crystallization kinetics of glass forming systems provides a priori knowledge of the ability of a given system to form a glass.

Multi-scale modeling of microstructure dependent intergranular brittle fracture using a quantitative phase-field based method

DOE PAGES

Chakraborty, Pritam; Zhang, Yongfeng; Tonks, Michael R.

2015-12-07

In this study, the fracture behavior of brittle materials is strongly influenced by their underlying microstructure that needs explicit consideration for accurate prediction of fracture properties and the associated scatter. In this work, a hierarchical multi-scale approach is pursued to model microstructure sensitive brittle fracture. A quantitative phase-field based fracture model is utilized to capture the complex crack growth behavior in the microstructure and the related parameters are calibrated from lower length scale atomistic simulations instead of engineering scale experimental data. The workability of this approach is demonstrated by performing porosity dependent intergranular fracture simulations in UO 2 and comparingmore » the predictions with experiments.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palmer, P.A.

The Lasagna project is the first of what we expect will be several large cooperative projects between industry consortia and government to develop improved remediation technologies. In 1992, Monsanto Company began contacting other major corporations to see if they were experiencing similar difficulties in applying cost-effective, or even workable technologies for industrial site remediation. Both General Electric and DuPont were early participants in the effort to develop a meeting with the EPA to discuss technical problems faced in cleanup, research needs, and ways to accelerate development of more cost-effective techniques. This paper provides some background on how this cooperative processmore » came to reality, what the Lasagna process is and how the cooperative arrangements and financing are structured.« less

Contentious Conversations: Using Mediation Techniques in Difficult Clinical Ethics Consultations.

PubMed

Fiester, Autumn

2015-01-01

Mediators utilize a wide range of skills in the process of facilitating dialogue and resolving conflicts. Among the most useful techniques for clinical ethics consultants (CECs)-and surely the least discussed-are those employed in acrimonious, hostile conversations between stakeholders. In the context of clinical ethics disputes or other bedside conflicts, good mediation skills can reverse the negative interactions that have prevented the creation of workable treatment plans or ethical consensus. This essay lays out the central framework mediators use in distinguishing positions from interests and describes a set of strategies for managing contentious ethics consultations or working with "difficult" patients, families, or patient-careprovider interactions. Copyright 2015 The Journal of Clinical Ethics. All rights reserved.

Oriented microtexturing on the surface of high-speed steel cutting tool

NASA Astrophysics Data System (ADS)

Filippov, A. V.; Tarasov, S. Yu.; Podgornyh, O. A.; Shamarin, N. N.; Filippova, E. O.

2016-11-01

Microtexturing the metal cutting tool surfaces is a novel technique intended for enhancing the workability of these tools. The microtexturing is used in machining the titanium alloys for air-space applications for reducing the adhesion wear of metal cutting blades. This paper is focused on forming the microtextured dotted, banded and overlapped areas on the surfaces of high-speed steel samples. The treated areas have been examined using laser scanning microscopy for the microtexture pattern and roughness. It has been shown that the microtextured surfaces obtained on the high-speed steel samples were free of cracks. Surface pattern and roughness of all three microtextured areas have been examined and analyzed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelic, Andjelka; Zagonel, Aldo A.

A system dynamics model was developed in response to the apparent decline in STEM candidates in the United States and a pending shortage. The model explores the attractiveness of STEM and STEM careers focusing on employers and the workforce. Policies such as boosting STEM literacy, lifting the H-1B visa cap, limiting the offshoring of jobs, and maintaining training are explored as possible solutions. The system is complex, with many feedbacks and long time delays, so solutions that focus on a single point of the system are not effective and cannot solve the problem. A deeper understanding of parts of themore » system that have not been explored to date is necessary to find a workable solution.« less

Pilot retrofit test of refrigerant R-134a for GDSCC

NASA Technical Reports Server (NTRS)

Albus, J.; Brown, B.; Dungao, M.; Spencer, G.

1994-01-01

NASA has issued an interim policy requiring all of its Centers to eliminate consumption (purchase) of stratospheric ozone-depleting substances, including chlorofluorocarbons (CFC's), by 1995. Also, plans must be outlined for the eventual phase out of their usage. The greatest source of CFC consumption and usage at the Goldstone Deep Space Communications Complex is refrigerant R-12, which is used in many of the facility's air-conditioning systems. A pilot retrofit test shows that retrofitting R-12 air-conditioning systems with hydrofluorocarbon R-13a would be a workable means to comply with the R-12 portion of NASA's policy. Results indicate acceptable cost levels and nearly equivalent system performance.

Multi-scale modeling of microstructure dependent intergranular brittle fracture using a quantitative phase-field based method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakraborty, Pritam; Zhang, Yongfeng; Tonks, Michael R.

In this study, the fracture behavior of brittle materials is strongly influenced by their underlying microstructure that needs explicit consideration for accurate prediction of fracture properties and the associated scatter. In this work, a hierarchical multi-scale approach is pursued to model microstructure sensitive brittle fracture. A quantitative phase-field based fracture model is utilized to capture the complex crack growth behavior in the microstructure and the related parameters are calibrated from lower length scale atomistic simulations instead of engineering scale experimental data. The workability of this approach is demonstrated by performing porosity dependent intergranular fracture simulations in UO 2 and comparingmore » the predictions with experiments.« less

Mechanical and physical properties of cement blended with sewage sludge ash.

PubMed

Garcés, P; Pérez Carrión, M; García-Alcocel, E; Payá, J; Monzó, J; Borrachero, M V

2008-12-01

The aim of this paper is to evaluate the compatibility of sewage sludge ash (SSA) with various types of commercially available cements (CEM I and CEM II types, cements with several proportions of clinker). The behaviour of mortars fabricated with various percentages (10-30% by weight) of the cement replaced by SSA has been analyzed in terms of workability, mechanical strength, porosity and shrinkage/expansion. SSA exhibits moderate pozzolanic activity; the highest compressive strengths were obtained with 10% of the cement replaced by SSA. The CEM II/B-M (V-LL) 42.5R cement is considered ideal for preparing mortars containing SSA. Shrinkage data demonstrate that sulphates present in SSA are not reactive towards cement.

Meeting the DHCP Challenge: A Model for Implementing a Decentralized Hospital Computer Program

PubMed Central

Catellier, Julie; Benway, Paula K.; Perez, Kathleen

1987-01-01

The James A. Haley Veterans' Hospital in Tampa has been a consistent leader in the implementation of automated systems within the VA. Our approach has been essentially to focus on obtaining maximum user involvement and contribution to the automation program within the Medical Center. Since clinical acceptance is vital to a viable program, a great deal of our efforts have been aimed at maximizing the training and participation of physicians, nurses and other clinical staff. The following is a description of our organization structure relative to this topic. We believe it to be a highly workable approach which can be easily implemented structurally at any hospital — public or private.

Optimum design of Geodesic dome’s jointing system

NASA Astrophysics Data System (ADS)

Tran, Huy. T.

2018-04-01

This study attempts to create a new design for joint connector of Geodesic dome. A new type of joint connector design is proposed for flexible rotating connection; comparing it to another, this design is cheaper and workable. After calculating the bearing capacity of the sample according to EC3 and Vietnam standard TCVN 5575-2012, FEM model of the design sample is carried out in many specific situation to consider the stress distribution, the deformation, the local destruction… in the connector. The analytical results and the FE data are consistent. The FE analysis also points out the behavior of some details that simple calculation cannot show. Hence, we can choose the optimum design of joint connector.

Evaluation of super-water reducers for highway applications

NASA Astrophysics Data System (ADS)

Whiting, D.

1981-03-01

Super-water reducers were characterized and evaluated as potential candidates for production of low water to cement ratio, high strength concretes for highway construction applications. Admixtures were composed of either naphthalene or melamine sulfonated formaldehyde condensates. A mini-slump procedure was used to assess dosage requirements and behavior of workability with time of cement pastes. Required dosage was found to be a function of tricalcium aluminate content, alkali content, and fineness of the cement. Concretes exhibited high rates of slump loss when super-water reducers were used. The most promising area of application of these products appears to be in production of dense, high cement content concrete using mobile concrete mixer/transporters.

Atomic Bomb: The Story of the Manhattan Project; How nuclear physics became a global geopolitical game-changer

NASA Astrophysics Data System (ADS)

Reed, Bruce Cameron

2015-06-01

This volume, prepared by an acknowledged expert on the Manhattan Project, gives a concise, fast-paced account of all major aspects of the project at a level accessible to an undergraduate college or advanced high-school student familiar with some basic concepts of energy, atomic structure, and isotopes. The text describes the underlying scientific discoveries that made nuclear weapons possible, how the project was organized, the daunting challenges faced and overcome in obtaining fissile uranium and plutonium, and in designing workable bombs, the dramatic Trinity test carried out in the desert of southern New Mexico in July 1945, and the bombings of Hiroshima and Nagasaki.

Mechanical Properties and Microstructure of Class C Fly Ash-Based Geopolymer Paste and Mortar.

PubMed

Li, Xueying; Ma, Xinwei; Zhang, Shoujie; Zheng, Enzu

2013-04-09

This paper presents workability, compressive strength and microstructure for geopolymer pastes and mortars made of class C fly ash at mass ratios of water-to-fly ash from 0.30 to 0.35. Fluidity was in the range of 145-173 mm for pastes and 131-136 mm for mortars. The highest strengths of paste and mortar were 58 MPa and 85 MPa when they were cured at 70 °C for 24 h. In XRD patterns, unreacted quartz and some reacted product were observed. SEM examination indicated that reacted product has formed and covered the unreacted particles in the paste and mortar that were consistent with their high strength.

Performance Measures for Evaluating Public Participation Activities in the Office of Environmental Management (DOE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carnes, S.A.

2001-02-15

Public participation in Office of Environmental Management (EM) activities throughout the DOE complex is a critical component of the overall success of remediation and waste management efforts. The challenges facing EM and its stakeholders over the next decade or more are daunting (Nuclear Waste News 1996). Achieving a mission composed of such challenges will require innovation, dedication, and a significant degree of good will among all stakeholders. EM's efforts to date, including obtaining and using inputs offered by EM stakeholders, have been notable. Public participation specialists have accepted and met challenges and have consistently tried to improve their performance. Theymore » have reported their experiences both formally and informally (e.g., at professional conferences and EM Public Participation Network Workshops, other internal meetings of DOE and contractor public participation specialists, and one-on-one consultations) in order to advance the state of their practice. Our research, and our field research in particular (including our interactions with many representatives of numerous stakeholder groups at nine DOE sites with diverse EM problems), have shown that it, is possible to develop coherent results even in a problem domain as complex as that of EM. We conclude that performance-based evaluations of public participation appear possible, and we have recommended an approach, based on combined and integrated multi-stakeholder views on the attributes of successful public participation and associated performance indicators, that seems workable and should be acceptable to diverse stakeholders. Of course, as an untested recommendation, our approach needs the validation that can only be achieved by application (perhaps at a few DOE sites with ongoing EM activities). Such an application would serve to refine the proposed approach in terms of its clarity, its workability, and its potential for full-scale use by EM and, potentially, other government agencies and private sector concerns.« less

Innovative farmers and regulatory gatekeepers: Genetically modified crops regulation and adoption in developing countries

PubMed Central

Sinebo, Woldeyesus; Maredia, Karim

2016-01-01

ABSTRACT The regulation of genetically modified (GM) crops is a topical issue in agriculture and environment over the past 2 decades. The objective of this paper is to recount regulatory and adoption practices in some developing countries that have successfully adopted GM crops so that aspiring countries may draw useful lessons and best practices for their biosafatey regulatory regimes. The first 11 mega-GM crops growing countries each with an area of more than one million hectares in 2014 were examined. Only five out of the 11 countries had smooth and orderly adoption of these crops as per the regulatory requirement of each country. In the remaining 6 countries (all developing countries), GM crops were either introduced across borders without official authorization, released prior to regulatory approval or unapproved seeds were sold along with the approved ones in violation to the existing regulations. Rapid expansion of transgenic crops over the past 2 decades in the developing world was a result of an intense desire by farmers to adopt these crops irrespective of regulatory roadblocks. Lack of workable biosafety regulatory system and political will to support GM crops encouraged unauthorized access to GM crop varieties. In certain cases, unregulated access in turn appeared to result in the adoption of substandard or spurious technology which undermined performance and productivity. An optimal interaction among the national agricultural innovation systems, biosafety regulatory bodies, biotech companies and high level policy makers is vital in making a workable regulated progress in the adoption of GM crops. Factoring forgone opportunities to farmers to benefit from GM crops arising from overregulation into biosafety risk analysis and decision making is suggested. Building functional biosafety regulatory systems that balances the needs of farmers to access and utilize the GM technology with the regulatory imperatives to ensure adequate safety to the environment and human health is recommended. PMID:26954893

Assessments of low emission asphalt mixtures produced using combinations of foaming agents

NASA Astrophysics Data System (ADS)

Mohd Hasan, Mohd Rosli

The asphalt foaming techniques have been used over the last couple of decades as an alternative to the traditional method of preparing asphalt mixtures. Based on positive feedback from the industry, this study was initiated to explore and evaluate the performance of the Warm Mix Asphalt (WMA) mixture produced through a foaming process using physical and chemical foaming agents, which are ethanol and sodium bicarbonate (NaHCO3), respectively. The success of this project may lead to new theories and provide an environmentally friendly technique to produce asphalt mixtures. This may advance the understanding of the foaming process and improve the performance of WMA to support sustainable development. Theoretically, ethanol can function in the same manner as water but requires less energy to foam due to its lower boiling point, 78°C. During the asphalt foaming process, numerous bubbles were generated by the vaporized ethanol, which significantly increased the volume of the asphalt binder, hence the coating potential of aggregates improves. The sodium bicarbonate was incorporated to enhance the quantity of bubbles and its stability. Therefore, understanding foaming agents, their solubility, chemical reactions, chemical function groups and rheological properties of the foamed binder are essential to help control the foam structure and final properties of the foamed WMA mixture. In order to understand the overall performance of newly developed foaming WMA, this material was evaluated for moisture susceptibility, rutting potential, and resistance to fracture and thermal cracking. The coatability, workability and compactability of foamed asphalt mixtures during production were also evaluated. Based on the results, it was found that the newly proposed foaming WMA has high potential to promote sustainable development by lowering the energy consumption and impacts on the environment. The ethanol is efficient in lowering the viscosity of asphalt binders, enhancing the workability, and having a higher expulsion rate from the foamed binder compared to water as a foaming agent. The addition of foaming agents to the asphalt binder has also lowered the activation energy of the asphalt binder, which has high potential in lowering the energy demand during production processes. The foamed WMA mixture prepared at 100°C was found to have behavior comparable with the control Hot Mix Asphalt (HMA) prepared at 155°C in terms of coatability, workability and compactability. Based on the mixture performance tests, the foamed WMA has a comparable or better performance than the HMA in terms of resistance to moisture damage, permanent deformation, fracture cracking and thermal cracking. The application of nano-hydrated lime is efficient in enhancing the aggregate coatability and improving the bearing capacity of asphalt pavement to lower the rutting potential and moisture susceptibility of foamed WMA mixtures. Limitations for each of the related parameters are also reported in this dissertation for the lab production of foamed WMA mixtures using ethanol and NaHCO 3 as foaming agents. The specified values were made based on the binder test, service characteristics and performance of foamed WMA mixtures in order to yield a comparable or better performance than the control HMA. Field validations should be carried out to understand the overall performance and durability of the proposed foaming WMA.

Image Analysis in Plant Sciences: Publish Then Perish.

PubMed

Lobet, Guillaume

2017-07-01

Image analysis has become a powerful technique for most plant scientists. In recent years dozens of image analysis tools have been published in plant science journals. These tools cover the full spectrum of plant scales, from single cells to organs and canopies. However, the field of plant image analysis remains in its infancy. It still has to overcome important challenges, such as the lack of robust validation practices or the absence of long-term support. In this Opinion article, I: (i) present the current state of the field, based on data from the plant-image-analysis.org database; (ii) identify the challenges faced by its community; and (iii) propose workable ways of improvement. Copyright © 2017 Elsevier Ltd. All rights reserved.

Engineering Data Compendium. Human Perception and Performance, Volume 1

NASA Technical Reports Server (NTRS)

Boff, Kenneth R. (Editor); Lincoln, Janet E. (Editor)

1988-01-01

The concept underlying the Engineering Data Compendium was the product an R and D program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design of military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by system designers. The present four volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is Volume 1, which contains sections on Visual Acquisition of Information, Auditory Acquisition of Information, and Acquisition of Information by Other Senses.

Space-based solar power conversion and delivery systems study. Volume 2: Engineering analysis

NASA Technical Reports Server (NTRS)

1977-01-01

The technical and economic feasibility of Satellite Solar Power Systems was studied with emphasis on the analysis and definition of an integrated strawman configuration concept, from which credible cost data could be estimated. Specifically, system concepts for each of the major subprogram areas were formulated, analyzed, and iterated to the degree necessary for establishing an overall, workable baseline system design. Cost data were estimated for the baseline and used to conduct economic analyses. The baseline concept selected was a 5-GW crystal silicon truss-type photovoltaic configuration, which represented the most mature concept available. The overall results and major findings, and the results of technical analyses performed during the final phase of the study efforts are reported.

Glimpsing over the event horizon: evolution of nuclear pores and envelope.

PubMed

Jékely, Gáspár

2005-02-01

The origin of eukaryotes from prokaryotic ancestors is one of the major evolutionary transitions in the history of life. The nucleus, a membrane bound compartment for confining the genome, is a central feature of eukaryotic cells and its origin also has to be a central feature of any workable theory that ventures to explain eukaryotic origins. Recent bioinformatic analyses of components of the nuclear pore complex (NPC), the nuclear envelope (NE), and the nuclear transport systems revealed exciting evolutionary connections (e.g., between NPC and coated vesicles) and provided a useful record of the phyletic distribution and history of NPC and NE components. These analyses allow us to refine theories on the origin and evolution of the nucleus, and consequently, of the eukaryotic cell.

A novel kind of concrete superplasticizer based on aryl isocyanate polycondensates

NASA Astrophysics Data System (ADS)

Ding, Bei; Qian, Shanshan; Qiu, Ying; Wang, Yi; Zheng, Chunyang; Wang, Gaoming

2017-03-01

A novel superplasticizer was synthesized by polycondensation of Alkyl phenol phosphate and toluene diisocyanate grafting with methoxy polyoxyethylene ether (MPEG). The chemical structure and molecular weight of polycondensates molecules were determined by 1H nuclear magnetic resonance (NMR) and gel permeation chromatography respectively. The experimental results indicated that the polycondensates of Alkyl phenol phosphate and toluene diisocyanate grafting with MPEG not only exhibited good water-reducing properties but also demonstrated effective anti-clay abilities alone. Furthermore, the polycondensates showed good fluidity maintaining abilities within 1-3 h and good workability of concrete. The results of T500 Time experiments show that lower plastic viscosity of the polycondensates leads to fresh concrete much “looser” than conventional PCEs in self-compacting concrete.

Still Virtual After All These Years: Recent Developments in the Virtual Solar Observatory

NASA Astrophysics Data System (ADS)

Gurman, J. B.; Bogart, R. S.; Davey, A. R.; Hill, F.; Martens, P. C.; Zarro, D. M.; Team, T. v.

2008-05-01

While continuing to add access to data from new missions, including Hinode and STEREO, the Virtual Solar Observatory is also being enhanced as a research tool by the addition of new features such as the unified representation of catalogs and event lists (to allow joined searches in two or more catalogs) and workable representation and manipulation of large numbers of search results (as are expected from the Solar Dynamics Observatory database). Working with our RHESSI colleagues, we have also been able to improve the performance of IDL-callable vso_search and vso_get functions, to the point that use of those routines is a practical alternative to reproducing large subsets of mission data on one's own LAN.

Geopolymer concretes: a green construction technology rising from the ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allouche, E.

2009-07-01

Researchers at Louisiana Tech University have embarked on a multi-year research initiative to develop applications for inorganic polymer concrete, or geopolymer concrete, in the area of civil construction, and to bring solve of these applications to market. One objective was to produce a spray-on coating for use in the harsh environment of wastewater conveyance and treatment facilities. Another project is to establish relationships between fly ash composition and particle size distribution and the mechanical attributes and workability of the resulting geopolymer concrete. A third project is to develop a 'smart' geopolymer concrete whose response to a given electric current canmore » be correlated to the stress level to which the structure is subjected. 1 fig., 6 photos.« less

Developing a Team-taught Capstone Course in Neuroscience.

PubMed

Kennedy, Susan; Hassebrock, Frank

2012-01-01

Capstone courses are becoming increasingly visible on college and university campuses. In this paper, we describe a capstone experience for undergraduate students pursuing our neuroscience concentration. The course is intended to provide an in-depth and interdisciplinary examination of contemporary topics in the field of neuroscience, and is designed for students who have completed the majority of requirements for the concentration. We describe the evolution of such a course, the goals and objectives of the course, and offer a workable model for similar courses in the context of a liberal arts institution. We summarize the positive aspects of such a course, describe the challenges involved in creating a course of this nature, and offer suggestions for successful similar capstone courses in Neuroscience.

[Fifty years of psychiatry at the interface between psyche and soma: a SWOT analysis].

PubMed

van Houdenhove, B; Luyten, P

2008-01-01

During the past 50 years the border area between psychiatry and somatic medicine has undergone remarkable changes. Theories have become better-founded, both psychologically and neurobiologically, research has become more sophisticated, and liaison-psychiatrists and health psychiatrist/behavioural medicine psychologists have played an increasingly active role in this domain. At the beginning of the 21st century modern psychosomatic medicine is facing new challenges; these include how to create a workable diagnostic classification system, how to instruct and educate both health professionals and lay-persons to an adequate level, how to utilize innovative research paradigms without having recourse to reductionism and how to implement in medical practice treatments that are geared to the needs of the individual patient.

Representing motion in a static image: constraints and parallels in art, science, and popular culture.

PubMed

Cutting, James E

2002-01-01

Representing motion in a picture is a challenge to artists, scientists, and all other imagemakers. Moreover, it presents a problem that will not go away with electronic and digital media, because often the pedagogical purpose of the representation of motion is more important than the motion itself. All satisfactory solutions evoke motion-for example, dynamic balance (or broken symmetry), stroboscopic sequences, affine shear (or forward lean), and photographic blur-but they also typically sacrifice the accuracy of the motion represented, a solution often unsuitable for science. Vector representations superimposed on static images allow for accuracy, but are not applicable to all situations. Workable solutions are almost certainly case specific and subject to continual evolution through exploration by imagemakers.

Engineering Data Compendium. Human Perception and Performance, Volume 2

NASA Technical Reports Server (NTRS)

Boff, Kenneth R. (Editor); Lincoln, Janet E. (Editor)

1988-01-01

The concept underlying the Engineering Data Compendium was the product of a Research and Development program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design of military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by system designers. The present volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is Volume 2, which contains sections on Information Storage and Retrieval, Spatial Awareness, Perceptual Organization, and Attention and Allocation of Resources.

The use of individualized contract plans as a method of performance evaluation for allied health faculty.

PubMed

Mitcham, M D; Vericella, B J

1985-11-01

Results from a two-year study of the individualized contract plan (ICP) approach to faculty evaluation indicate this is a workable method of performance evaluation for allied health faculty. The ICP was found to be individualized, systematic, flexible, and objective. Faculty members and department chairpersons differed in their perception of the effectiveness of the ICP, but both groups supported its continued use. Five major recommendations were made regarding the continued use of the ICP as a method of faculty performance evaluation: (1) separate evaluation and professional development aspects, (2) link results to the institutional reward structure, (3) administer the ICP uniformly among departments, (4) develop a monitoring mechanism, and (5) foster open communication among all participants in the system.

Finite element simulations and experimental investigations on ductile fracture in cold forging of aluminum alloy

NASA Astrophysics Data System (ADS)

Amiri, Amir; Nikpour, Amin; Saraeian, Payam

2018-05-01

Forging is one of the manufacturing processes of aluminium parts which has two major categories: called hot and cold forging. In the cold forging, the dimensional and geometrical accuracy of final part is high. However, fracture may occur in some aluminium alloys during the process because of less workability. Fracture in cold forging can be in the form of ductile, brittle or combination of both depending on the alloy type. There are several criteria for predicting fracture in cold forging. In this study, cold forging process of 6063 aluminium alloy for three different parts is simulated in order to predict fracture. The results of numerical simulations of Freudenthal criterion is in conformity with experimental tests.

Engineering data compendium. Human perception and performance, volume 3

NASA Technical Reports Server (NTRS)

Boff, Kenneth R. (Editor); Lincoln, Janet E. (Editor)

1988-01-01

The concept underlying the Engineering Data Compendium was the product of a research and development program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design of military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by system designers. The present four volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is Volume 3, containing sections on Human Language Processing, Operator Motion Control, Effects of Environmental Stressors, Display Interfaces, and Control Interfaces (Real/Virtual).

Ethics in American health 1: ethical approaches to health policy.

PubMed

Ruger, Jennifer Prah

2008-10-01

I trace the evolution of ethical approaches to health policy in the United States and examine a number of critical unresolved issues pertaining to the current set of frameworks. Several themes emerge. First, fair procedures claim more attention than substantive and procedural principles. Second, in the case of public deliberation, more focus has been placed on factors such as procedural mechanisms than on understanding how individuals and groups value different aspects of health and agree on health-related decisions. Third, the nation needs workable frameworks to guide collective choices about valuable social ends and their trade-offs; purely procedural strategies are limited in illuminating overarching health policy and ethics questions. There is a need to integrate consequential and procedural approaches to health ethics and policy.

Catheter-based photoacoustic endoscope

PubMed Central

Yang, Joon-Mo; Li, Chiye; Chen, Ruimin; Zhou, Qifa; Shung, K. Kirk; Wang, Lihong V.

2014-01-01

Abstract. We report a flexible shaft-based mechanical scanning photoacoustic endoscopy (PAE) system that can be potentially used for imaging the human gastrointestinal tract via the instrument channel of a clinical video endoscope. The development of such a catheter endoscope has been an important challenge to realize the technique’s benefits in clinical settings. We successfully implemented a prototype PAE system that has a 3.2-mm diameter and 2.5-m long catheter section. As the instrument’s flexible shaft and scanning tip are fully encapsulated in a plastic catheter, it easily fits within the 3.7-mm diameter instrument channel of a clinical video endoscope. Here, we demonstrate the intra-instrument channel workability and in vivo animal imaging capability of the PAE system. PMID:24887743

Overview of the Inland California Translational Consortium

NASA Astrophysics Data System (ADS)

Malkas, Linda H.

2017-05-01

The mission of the Inland California Translational Consortium (ICTC), an independent research consortium comprising a unique hub of regional institutions (City of Hope [COH], California Institute of Technology [Caltech], Jet Propulsion Laboratory [JPL], University of California Riverside [UCR], and Claremont Colleges Keck Graduate Institute [KGI], is to institute a new paradigm within the academic culture to accelerate translation of innovative biomedical discoveries into clinical applications that positively affect human health and life. The ICTC actively supports clinical translational research as well as the implementation and advancement of novel education and training models for the translation of basic discoveries into workable products and practices that preserve and improve human health while training and educating at all levels of the workforce using innovative forward-thinking approaches.

A 15,000-hour cyclic endurance test of an 8-centimeter-diameter electron bombardment mercury ion thruster

NASA Technical Reports Server (NTRS)

Nakanishi, S.

1976-01-01

A laboratory model 8 cm thruster with improvements to minimize ion chamber erosion and peeling of sputtered metal was subjected to a cyclic endurance test for 15,040 hours and 460 restarts. A charted history of several thruster operating variables and off-normal events are shown in 600-hour segments at three points in the test. The transient behavior of these variables during a typical start-stop cycle is presented. Finding of the post-test inspection confirmed most of the expected results. Charge exchange ions caused normal accelerator grid erosion. The workability of the various design features was substantiated, and attainable improvements in propellant utilization efficiency should significantly reduce accelerator erosion.

The micromechanics model analysis of the viscosity regulation of ultra-high strength concrete with low viscosity

NASA Astrophysics Data System (ADS)

Zhu, M.; Wang, F. G.; Wang, F. Z.; Liu, Y. P.

2017-02-01

The plastic viscosity of mortar and concrete with different binder content, sand ratio, water-binder ratio, microbead dosage and different class and dosage of fly ash were tested and calculated according tomicromechanics model proposed by A. Ghanbari and B.L. Karihaloo, The correlations between these parameters and fresh concrete workability were also investigated, which showed i. high consistence with the objective reality. When binder content, microbead dosage, fly ash dosage or the water-binder ratio was increased or sand ratio was reduced, the fresh concrete viscosity would decrease correspondingly. However their effects were not that same. The relationships between T50 a, V-funnel and inverted slump time with fresh concrete viscosity were established, respectively.

Engineering data compendium. Human perception and performance. User's guide

NASA Technical Reports Server (NTRS)

Boff, Kenneth R. (Editor); Lincoln, Janet E. (Editor)

1988-01-01

The concept underlying the Engineering Data Compendium was the product of a research and development program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design and military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from the existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by systems designers. The present four volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is the first volume, the User's Guide, containing a description of the program and instructions for its use.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krause, R.A.; Patel, D.I.; Gathy, B.D.

This report on how public transit is financed today was written from the point of view of the states' current fiscal condition. While the economic forecast varies from state to state, not one projects a future of growing surpluses. The report documents and analyzes mass-transit funding sources, both past and present, and looks at their future potential. The 12-state overview may help others uncover methods and programs workable in their situations. The survey findings regarding the question - How do states finance their mass-transit programs - show that states use revenues from various sources such as license fees, bond issues,more » highway user taxes, tolls and so on. States are exploring new funding mechanisms such as special assessment districts, public/private ventures, lottery funds, and so on.« less

Developing a Team-taught Capstone Course in Neuroscience

PubMed Central

Kennedy, Susan; Hassebrock, Frank

2012-01-01

Capstone courses are becoming increasingly visible on college and university campuses. In this paper, we describe a capstone experience for undergraduate students pursuing our neuroscience concentration. The course is intended to provide an in-depth and interdisciplinary examination of contemporary topics in the field of neuroscience, and is designed for students who have completed the majority of requirements for the concentration. We describe the evolution of such a course, the goals and objectives of the course, and offer a workable model for similar courses in the context of a liberal arts institution. We summarize the positive aspects of such a course, describe the challenges involved in creating a course of this nature, and offer suggestions for successful similar capstone courses in Neuroscience. PMID:23493882

Still Virtual After All These Years: Recent Developments in the Virtual Solar Observatory

NASA Technical Reports Server (NTRS)

Gurman, Joseph B.; Bogart; Davey; Hill; Masters; Zarro

2008-01-01

While continuing to add access to data from new missions, including Hinode and STEREO, the Virtual Solar Observatory is also being enhanced as a research tool by the addition of new features such as the unified representation of catalogs and event lists (to allow joined searches in two or more catalogs) and workable representation and manipulation of large numbers of search results (as are expected from the Solar Dynamics Observatory database). Working with our RHESSI colleagues, we have also been able to improve the performance of IDL-callable vso_search and vso_get functions, to the point that use of those routines is a practical alternative to reproducing large subsets of mission data on one's own LAN.

Efficient synthetic methods for the installation of boron-nitrogen bonds in conjugated organic molecules.

PubMed

Morgan, Matthew M; Piers, Warren E

2016-04-14

Polycyclic aromatic hydrocarbons in which one or more CC units have been replaced by isoelectronic BN units have attracted interest as potentially improved organic materials in various devices. This promise has been hampered by a lack of access to gram quantities of these materials. However, the exploitation of keystone reactions such as ring closing metathesis, borylative cyclization of amino styrenes and electrophilic borylation has lead to strategies for access to workable amounts of material. These strategies can be augmented by judicious postfunctionalization reactions to diversify the library of materials available. This Frontier article highlights some of the recent successes and shows that the long promised applications of BN-doped PAHs are beginning to be explored in a meaningful way.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Froehlich, D.P.; Schumacher, J.A.

This is a quarterly progress report describing recent efforts aimed at building and testing the Field Grid Sense (FGS) system for yield mapping and machine control during harvesting. Secondly, the aim is to use Field Grid Sense with chemical application equipment to demonstrate a workable in-field system. More specifically, the operation of the patented hardware/software FGS system will be tested in crop harvesting to demonstrate the systems` utility and to analyze the flexibility of operation under true field conditions. Additionally, FGS will again be used with chemical application equipment -- equipment that needs modification to correct one or two slightmore » shortcomings. This action will create improved systems and establish the worthiness, efficiency and necessity of chemical application equipment that is controlled and directed via the FGS package.« less

Mechanical Properties and Microstructure of Class C Fly Ash-Based Geopolymer Paste and Mortar

PubMed Central

Li, Xueying; Ma, Xinwei; Zhang, Shoujie; Zheng, Enzu

2013-01-01

This paper presents workability, compressive strength and microstructure for geopolymer pastes and mortars made of class C fly ash at mass ratios of water-to-fly ash from 0.30 to 0.35. Fluidity was in the range of 145–173 mm for pastes and 131–136 mm for mortars. The highest strengths of paste and mortar were 58 MPa and 85 MPa when they were cured at 70 °C for 24 h. In XRD patterns, unreacted quartz and some reacted product were observed. SEM examination indicated that reacted product has formed and covered the unreacted particles in the paste and mortar that were consistent with their high strength. PMID:28809222

Social Media, Power, and the Future of VBAC.

PubMed

Romano, Amy M; Gerber, Hilary; Andrews, Desirre

2010-01-01

The Internet has been called a disruptive technology because it has shifted power and altered the economics of doing business, whether that business is selling books or providing health care. Social media have accelerated the pace of disruption by enabling interactive information sharing and blurring the lines between the "producers" and "consumers" of knowledge, goods, and services. In the wake of the National Institutes of Health Consensus Development Conference on Vaginal Birth After Cesarean (VBAC) and major national recommendations for maternity care reform, activated, engaged consumers face an unprecedented opportunity to drive meaningful changes in VBAC access and safety. This article examines the role of social networks in informing women about VBAC, producing low-cost, accessible decision aids, and enabling multi-stakeholder collaborations toward workable solutions that remove barriers women face in accessing VBAC.

Studies of thermochemical water-splitting cycles

NASA Technical Reports Server (NTRS)

Remick, R. J.; Foh, S. E.

1980-01-01

Higher temperatures and more isothermal heat profiles of solar heat sources are developed. The metal oxide metal sulfate class of cycles were suited for solar heat sources. Electrochemical oxidation of SO2 and thermochemical reactions are presented. Electrolytic oxidation of sulfur dioxide in dilute sulfuric acid solutions were appropriate for metal oxide metal sulfate cycles. The cell voltage at workable current densities required for the oxidation of SO2 was critical to the efficient operation of any metal oxide metal sulfate cycle. A sulfur dioxide depolarized electrolysis cell for the splitting of water via optimization of the anode reaction is discussed. Sulfuric acid concentrations of 30 to 35 weight percent are preferred. Platinized platinum or smooth platinum gave the best anode kinetics at a given potential of the five materials examined.

Rewarding peer reviewers: maintaining the integrity of science communication.

PubMed

Gasparyan, Armen Yuri; Gerasimov, Alexey N; Voronov, Alexander A; Kitas, George D

2015-04-01

This article overviews currently available options for rewarding peer reviewers. Rewards and incentives may help maintain the quality and integrity of scholarly publications. Publishers around the world implemented a variety of financial and nonfinancial mechanisms for incentivizing their best reviewers. None of these is proved effective on its own. A strategy of combined rewards and credits for the reviewers1 creative contributions seems a workable solution. Opening access to reviews and assigning publication credits to the best reviews is one of the latest achievements of digitization. Reviews, posted on academic networking platforms, such as Publons, add to the transparency of the whole system of peer review. Reviewer credits, properly counted and displayed on individual digital profiles, help distinguish the best contributors, invite them to review and offer responsible editorial posts.

Effect of Admixtures on the Yield Stresses of Cement Pastes under High Hydrostatic Pressures

PubMed Central

Yim, Hong Jae; Kim, Jae Hong; Kwon, Seung Hee

2016-01-01

When cement-based materials are transported at a construction site, they undergo high pressures during the pumping process. The rheological properties of the materials under such high pressures are unknown, and estimating the workability of the materials after pumping is a complex problem. Among various influential factors on the rheology of concrete, this study investigated the effect of mineral and chemical admixtures on the high-pressure rheology. A rheometer was fabricated that could measure the rheological properties while maintaining a high pressure to simulate the pumping process. The effects of superplasticizer, silica fume, nanoclay, fly ash, or ground granulated blast furnace slag were investigated when mixed with two control cement pastes. The water-to-cement ratios were 0.35 and 0.50. PMID:28773273

The "real world" barriers and solutions to Candida vaccine patent prosecutions

PubMed Central

Wang, Shyh-Jen

2012-01-01

The US Patent and Trademark Office (USPTO) adopts recent patent courts’ opinions (such as KSR In re Fisher and Ariad v. Lilly) in patent examinations, which would certainly create barriers to biotech patent prosecution. To identify the barriers to Candida vaccine patent prosecution, we analyzed 99 US-granted patents from January 2001 to May 2012 related to Candida vaccines. The rejections were based on factors that included obviousness, novelty, indefiniteness, double patenting, enablement, written description and utility. Based on this investigation, we find that some of these rejections were actually avoidable, and then further provide workable solutions to avoid some of the barriers, especially those related to patentability. These principles recited in this study should also be applicable to other fields of vaccines and immunotherapeutics. PMID:22894949

Edge-illumination x-ray phase contrast imaging with Pt-based metallic glass masks

NASA Astrophysics Data System (ADS)

Saghamanesh, Somayeh; Aghamiri, Seyed Mahmoud-Reza; Olivo, Alessandro; Sadeghilarijani, Maryam; Kato, Hidemi; Kamali-Asl, Alireza; Yashiro, Wataru

2017-06-01

Edge-illumination x-ray phase contrast imaging (EI XPCI) is a non-interferometric phase-sensitive method where two absorption masks are employed. These masks are fabricated through a photolithography process followed by electroplating which is challenging in terms of yield as well as time- and cost-effectiveness. We report on the first implementation of EI XPCI with Pt-based metallic glass masks fabricated by an imprinting method. The new tested alloy exhibits good characteristics including high workability beside high x-ray attenuation. The fabrication process is easy and cheap, and can produce large-size masks for high x-ray energies within minutes. Imaging experiments show a good quality phase image, which confirms the potential of these masks to make the EI XPCI technique widely available and affordable.

Ethics in American Health 1: Ethical Approaches to Health Policy

PubMed Central

2008-01-01

I trace the evolution of ethical approaches to health policy in the United States and examine a number of critical unresolved issues pertaining to the current set of frameworks. Several themes emerge. First, fair procedures claim more attention than substantive and procedural principles. Second, in the case of public deliberation, more focus has been placed on factors such as procedural mechanisms than on understanding how individuals and groups value different aspects of health and agree on health-related decisions. Third, the nation needs workable frameworks to guide collective choices about valuable social ends and their trade-offs; purely procedural strategies are limited in illuminating overarching health policy and ethics questions. There is a need to integrate consequential and procedural approaches to health ethics and policy. PMID:18703449

The role of lipid nanoparticles and its surface modification in reaching the brain: an approach for neurodegenerative diseases treatment.

PubMed

Pedraz, Jose Luis; Igartua, Manoli; Maria, Rosa; Hernando, Sara

2018-05-09

Nanomedicine is a field of science that employs materials in the nanometer scale. Specifically, the use of nanoparticles (NPs) has some medical applications due to their structure, for example, the ability to cross the biological barriers, and their effectiveness avoiding some drug delivery problems. Because of that, in the last years, the use of NPs has been raised as a workable solution for neurodegenerative diseases (ND) treatment [1,2]. NDs are characterized by a continuous structural and functional neuronal loss, usually correlated with neuronal death. Between NDs, Alzheimer disease (AD) and Parkinson's disease (PD) are the most common disorders worldwide, becoming a serious economic burden and public health problem [3]. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Eliminating barriers to personalized medicine

PubMed Central

2014-01-01

With the emergence of high-throughput discovery platforms, robust preclinical small-animal models, and efficient clinical trial pipelines, it is becoming possible to envision a time when the treatment of human neurologic diseases will become personalized. The emergence of precision medicine will require the identification of subgroups of patients most likely to respond to specific biologically based therapies. This stratification only becomes possible when the determinants that contribute to disease heterogeneity become more fully elucidated. This review discusses the defining factors that underlie disease heterogeneity relevant to the potential for individualized brain tumor (optic pathway glioma) treatments arising in the common single-gene cancer predisposition syndrome, neurofibromatosis type 1 (NF1). In this regard, NF1 is posited as a model genetic condition to establish a workable paradigm for actualizing precision therapeutics for other neurologic disorders. PMID:24975854

Comparing the use of sewage sludge ash and glass powder in cement mortars.

PubMed

Chen, Zhen; Poon, Chi Sun

2017-06-01

This study explored the suitability of using sewage sludge ash (SSA) and mixed-colored glass powder (MGP) as construction materials in cement mortars. Positive findings from this study may help promote the recycling of waste SSA and MGP in construction works. The results indicated that the SSA decreased while MGP improved the mortar workability. The SSA exhibited very low pozzolanic activity, but the cement mortar prepared with 20% SSA yielded strength values slightly superior to those of the glass mortars due to its water absorption ability. MGP can serve as a pozzolan and when 20% of cement was replaced by MGP, apparent compressive strength gains were found at later curing ages. The SSA could be used to mitigate ASR expansion while the MGP was superior in resisting drying shrinkage.

Rewarding Peer Reviewers: Maintaining the Integrity of Science Communication

PubMed Central

2015-01-01

This article overviews currently available options for rewarding peer reviewers. Rewards and incentives may help maintain the quality and integrity of scholarly publications. Publishers around the world implemented a variety of financial and nonfinancial mechanisms for incentivizing their best reviewers. None of these is proved effective on its own. A strategy of combined rewards and credits for the reviewers1 creative contributions seems a workable solution. Opening access to reviews and assigning publication credits to the best reviews is one of the latest achievements of digitization. Reviews, posted on academic networking platforms, such as Publons, add to the transparency of the whole system of peer review. Reviewer credits, properly counted and displayed on individual digital profiles, help distinguish the best contributors, invite them to review and offer responsible editorial posts. PMID:25829801

Generic, Type-Safe and Object Oriented Computer Algebra Software

NASA Astrophysics Data System (ADS)

Kredel, Heinz; Jolly, Raphael

Advances in computer science, in particular object oriented programming, and software engineering have had little practical impact on computer algebra systems in the last 30 years. The software design of existing systems is still dominated by ad-hoc memory management, weakly typed algorithm libraries and proprietary domain specific interactive expression interpreters. We discuss a modular approach to computer algebra software: usage of state-of-the-art memory management and run-time systems (e.g. JVM) usage of strongly typed, generic, object oriented programming languages (e.g. Java) and usage of general purpose, dynamic interactive expression interpreters (e.g. Python) To illustrate the workability of this approach, we have implemented and studied computer algebra systems in Java and Scala. In this paper we report on the current state of this work by presenting new examples.

Implications for complex cognition from the hafting of tools with compound adhesives in the Middle Stone Age, South Africa

PubMed Central

Wadley, Lyn; Hodgskiss, Tamaryn; Grant, Michael

2009-01-01

Compound adhesives made from red ochre mixed with plant gum were used in the Middle Stone Age (MSA), South Africa. Replications reported here suggest that early artisans did not merely color their glues red; they deliberately effected physical transformations involving chemical changes from acidic to less acidic pH, dehydration of the adhesive near wood fires, and changes to mechanical workability and electrostatic forces. Some of the steps required for making compound adhesive seem impossible without multitasking and abstract thought. This ability suggests overlap between the cognitive abilities of modern people and people in the MSA. Our multidisciplinary analysis provides a new way to recognize complex cognition in the MSA without necessarily invoking the concept of symbolism. PMID:19433786

Managed Entry Agreements for Pharmaceuticals in the Context of Adaptive Pathways in Europe.

PubMed

Bouvy, Jacoline C; Sapede, Claudine; Garner, Sarah

2018-01-01

As per the EMA definition, adaptive pathways is a scientific concept for the development of medicines which seeks to facilitate patient access to promising medicines addressing high unmet need through a prospectively planned approach in a sustainable way. This review reports the findings of activities undertaken by the ADAPT-SMART consortium to identify enablers and explore the suitability of managed entry agreements for adaptive pathways products in Europe. We found that during 2006-2016 outcomes-based managed entry agreements were not commonly used for products with a conditional marketing authorization or authorized under exceptional circumstances. The barriers and enablers to develop workable managed entry agreements models for adaptive pathways products were discussed through interviews and a multi-stakeholder workshop with a number of recommendations made in this paper.

[Lifestyle interventions at work?].

PubMed

Hulshof, Carel T J

2013-01-01

So far many worksite lifestyle or health promotion programmes have shown only moderate evidence of effectiveness and cost-effectiveness. However, participation in work is in itself an important determinant of health. For this reason ensuring of fitting work and sustained workability should be an aspect of health policy. Workers' health is not only determined by their working environment but also by health practices and lifestyle factors. Under certain preconditions (e.g. on a voluntary basis, confidentiality, integration with health protection) lifestyle interventions during work time can contribute to a healthier working population. As such programmes may result in financial and social benefits for employers, they should be partly responsible for paying the costs. From a societal perspective, governmental commitment to a preventive policy and the involvement of health and income insurance companies are also required.

Use of steel slag as a new material for roads

NASA Astrophysics Data System (ADS)

Ochoa Díaz, R.; Romero Farfán, M.; Cardenas, J.; Forero, J.

2017-12-01

This research paper aims to analyse the behaviour of MDC-19 hot dense asphalt mixtures with steel slag as coarse aggregate, by using asphalt 80-100, in order to verify if this residue has suitable characteristics that allow its use. The physical and mechanical characterization was accomplished using phosphorous slag from the company Acerías Paz del Río S.A. The working formula was then determined for each mixture using the RAMCODES methodology, the briquettes were produced in the laboratory and then, the design verification was performed. Taking into account the results obtained, it is concluded that the use of phosphorous slag as coarse aggregate in asphalt mixtures is workable, since acceptable design parameters and verification are obtained that meet the specifications for use as a rolling layer.

An overall approach to health care for indigenous peoples.

PubMed

King, Malcolm

2009-12-01

Indigenous peoples across all the continents of the globe live with major gaps in health status and health outcomes associated with well-described social determinants of health, such as poverty and poor education. Indigenous peoples face additional health determinant issues associated with urbanization, isolation from traditional territories, and loss of cultural continuity. Indigenous children are particularly vulnerable as they grow up in isolation from their cultural and social roots and yet are also separated from the mainstream environment of their society. Programs to address these difficult health issues should be viewed as complex clinical interventions with health researchers, social scientists, and clinicians working together with Indigenous peoples to identify the most pressing needs and most appropriate and workable solutions that will result in effective policies and practices.

Roles of airships in economic development

NASA Technical Reports Server (NTRS)

Beier, G. J.; Hidalgo, G. C.

1975-01-01

It is proposed that airships of known and tested technology could, in some cases, perform routine transport missions more economically than conventional transport modes. If infrastructure for direct surface transport is already in place or if such infrastructure can be justified by the size of the market and there are no unusual impediments to constructing it, then the airships of tested technology cannot normally compete. If, however, the surface routes would be unusually expensive or circuitous, or if they involve several transhipments, or if the market size is too small to spread infrastructure costs of conventional transport, the airships of tested technology present a workable alternative. A series of special cases are considered. The cases, though unusual, are not unique; there are several similar possible applications which, in total, would provide a reasonably large market for airships.

a Floating Mobile Quay for Super Container Ships in a Hub Port

NASA Astrophysics Data System (ADS)

Chae, Jang-Won; Park, Woo-Sun

A floating mobile quay (FMQ), which is an innovative berth system, has functions of not only both side loading/unloading but also direct transshipment to feeder ships in a hub port. Applying the FMQ to a hub port such as the west terminal of Busan New Port of Korea, it is shown from a physical modeling and field model test that the quay is dynamically stable and workable in the prevailing wave condition and also safe in a design storm condition, respectively. The terminal productivity is increased by 30% comparing with the present land based berth. The B/C ratio of the new berth system is evaluated as 1.13 considering super-large container ships. It appears that the FMQ is a technically and economically feasible system in the hub port.

Some thoughts on the management of large, complex international space ventures

NASA Astrophysics Data System (ADS)

Lee, T. J.; Kutzer, Ants; Schneider, W. C.

The nations of the world have already collaborated on a number of joint space ventures of varying complexities. To name a few of the variations in management arrangements, the schemes have included the utilization of one nation's spacecraft to orbit another's experiment, the launch of another's spacecraft, the development of an offline article (such as the Spacelab), and the cooperative development of the Space Station Freedom (S.S. Freedom). Today, as the scope of the problems and solutions involved in establishing a permanently manned colony on the Moon and exploring the surface of Mars become clearer, the idea of a major sharing of the enormous tasks among the spacefaring nations seems more and more necessary and, indeed, required. For such a major, complex project, success depends upon the management as much as it does on the technology. If the project is not organized in a logical and workable manner with clear areas of responsibility and with an agreed-to chain of command, it is in as much jeopardy as it is if the resources are not available. It is vital that thought and analysis be put on this aspect of a "Mission from Planet Earth" early, to insure that the project is not divided into an impractical organizational structure and that agreements are not made which are unsound. As an example of the questions to be explored, the lead organization can take many forms. Clearly, there must be a recognized leader to make the many difficult programmatic decisions which will arise. The lead could be assigned to one nation; it could be assigned to a new international group; it could be assigned to a consortium; or granted to a committee. Each has implications and problems to be explored. This paper will open the discussions. It is the intent of this paper to begin the process based upon the authors' experiences in various international projects. It is to arouse interest and discussion not to select a final solution. Final solutions will depend upon capabilities, financial regards, and politics (some of the variables), and the management scheme will have to take all into account. The scheme selected must be firm, logical, and workable.

Effect of care management program structure on implementation: a normalization process theory analysis.

PubMed

Holtrop, Jodi Summers; Potworowski, Georges; Fitzpatrick, Laurie; Kowalk, Amy; Green, Lee A

2016-08-15

Care management in primary care can be effective in helping patients with chronic disease improve their health status, however, primary care practices are often challenged with implementation. Further, there are different ways to structure care management that may make implementation more or less successful. Normalization process theory (NPT) provides a means of understanding how a new complex intervention can become routine (normalized) in practice. In this study, we used NPT to understand how care management structure affected how well care management became routine in practice. Data collection involved semi-structured interviews and observations conducted at 25 practices in five physician organizations in Michigan, USA. Practices were selected to reflect variation in physician organizations, type of care management program, and degree of normalization. Data were transcribed, qualitatively coded and analyzed, initially using an editing approach and then a template approach with NPT as a guiding framework. Seventy interviews and 25 observations were completed. Two key structures for care management organization emerged: practice-based care management where the care managers were embedded in the practice as part of the practice team; and centralized care management where the care managers worked independently of the practice work flow and was located outside the practice. There were differences in normalization of care management across practices. Practice-based care management was generally better normalized as compared to centralized care management. Differences in normalization were well explained by the NPT, and in particular the collective action construct. When care managers had multiple and flexible opportunities for communication (interactional workability), had the requisite knowledge, skills, and personal characteristics (skill set workability), and the organizational support and resources (contextual integration), a trusting professional relationship (relational integration) developed between practice providers and staff and the care manager. When any of these elements were missing, care management implementation appeared to be affected negatively. Although care management can introduce many new changes into delivery of clinical practice, implementing it successfully as a new complex intervention is possible. NPT can be helpful in explaining differences in implementing a new care management program with a view to addressing them during implementation planning.

Social Media, Power, and the Future of VBAC

PubMed Central

Romano, Amy M.; Gerber, Hilary; Andrews, Desirre

2010-01-01

The Internet has been called a disruptive technology because it has shifted power and altered the economics of doing business, whether that business is selling books or providing health care. Social media have accelerated the pace of disruption by enabling interactive information sharing and blurring the lines between the “producers” and “consumers” of knowledge, goods, and services. In the wake of the National Institutes of Health Consensus Development Conference on Vaginal Birth After Cesarean (VBAC) and major national recommendations for maternity care reform, activated, engaged consumers face an unprecedented opportunity to drive meaningful changes in VBAC access and safety. This article examines the role of social networks in informing women about VBAC, producing low-cost, accessible decision aids, and enabling multi-stakeholder collaborations toward workable solutions that remove barriers women face in accessing VBAC. PMID:21170180

The "real world" barriers and solutions to Candida vaccine patent prosecutions: an analysis of U.S. Patent and Trademark Office actions on related applications.

PubMed

Wang, Shyh-Jen

2012-10-01

The US Patent and Trademark Office (USPTO) adopts recent patent courts' opinions (such as KSR In re Fisher and Ariad v. Lilly) in patent examinations, which would certainly create barriers to biotech patent prosecution. To identify the barriers to Candida vaccine patent prosecution, we analyzed 99 US-granted patents from January 2001 to May 2012 related to Candida vaccines. The rejections were based on factors that included obviousness, novelty, indefiniteness, double patenting, enablement, written description and utility. Based on this investigation, we find that some of these rejections were actually avoidable, and then further provide workable solutions to avoid some of the barriers, especially those related to patentability. These principles recited in this study should also be applicable to other fields of vaccines and immunotherapeutics.

From stack-firing to pyromania: medico-legal concepts of insane arson in British, US and European contexts, c. 1800-1913. Part 2 .

PubMed

Andrews, Jonathan

2010-12-01

The second part of this paper explores deepening doubts about pyromania as a special insanity, British debates post-1890, and pyromania's supplanting with the broader diagnostic category of insane incendiarism. It assesses the conceptual importance of revenge and morbid-motivations for arson, and the relationship of Victorian and Edwardian concepts of arson to more modern psychiatric research.The main objective is to ascertain the extent to which Victorian and Edwardian medico-psychologists and medical legists arrived at meaningful and workable definitions of criminal insanity linked to arson. It concludes by emphasizing the limitations, contentiousness and inconsistencies in the use of technical terms such as'pyromania', contrasted with the qualified success of authorities in arriving at more viable and broadly acceptable explanations of insane firesetting.

Development and successful application of a "Community-First" communication model for community-based environmental health research.

PubMed

Emmett, Edward Anthony; Zhang, Hong; Shofer, Frances Susan; Rodway, Nancy; Desai, Chintan; Freeman, David; Hufford, Mary

2009-02-01

Effectively communicate results from a community exposure study to meet predetermined community priorities, maintaining ethical principles of autonomy, empowerment and justice. The community established principles for the communications and a plan to inform study participants, community and other stakeholders of results and recommendations in a novel sequence: the "Community-First" communication model. The communications resulted in positive actions including company sponsored free bottled water, accepted by 77.6% of eligible households. Over 95% of participants in a follow-up survey had made some change to residential water supplies. Serum perfluorooctanoate levels were reduced. Government agencies acted on the results. The unique communication approach generated workable solutions to the problem investigated, raised community awareness and modified behaviors. Information generated a "free market" of community-level solutions. Each major stakeholder voluntarily adopted a "precautionary principle."

Status of the atomized uranium silicide fuel development at KAERI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, C.K.; Kim, K.H.; Park, H.D.

1997-08-01

While developing KMRR fuel fabrication technology an atomizing technique has been applied in order to eliminate the difficulties relating to the tough property of U{sub 3}Si and to take advantage of the rapid solidification effect of atomization. The comparison between the conventionally comminuted powder dispersion fuel and the atomized powder dispersion fuel has been made. As the result, the processes, uranium silicide powdering and heat treatment for U{sub 3}Si transformation, become simplified. The workability, the thermal conductivity and the thermal compatibility of fuel meat have been investigated and found to be improved due to the spherical shape of atomized powder.more » In this presentation the overall developments of atomized U{sub 3}Si dispersion fuel and the planned activities for applying the atomizing technique to the real fuel fabrication are described.« less

A novel grounded to floating admittance converter with electronic control

NASA Astrophysics Data System (ADS)

Prasad, Dinesh; Ahmad, Javed; Srivastava, Mayank

2018-01-01

This article suggests a new grounded to floating admittance convertor employing only two voltage differencing transconductance amplifiers (VDTAs). The proposed circuit can convert any arbitrary grounded admittance into floating admittance with electronically controllable scaling factor. The presented converter enjoys the following beneficial: (1) no requirement of any additional passive element (2) scaling factor can be tuned electronically through bias currents of VDTAs (3) no matching constraint required (4) low values of active/passive sensitivity indexes and (5) excellent non ideal behavior that indicates no deviation in circuit behavior even under non ideal environment. Application of the proposed configuration in realization of floating resistor and floating capacitor has been presented and the workability of these floating elements has been confirmed by active filter design examples. SPICE simulations have been performed to demonstrate the performance of the proposed circuits.

Analysis of the eukaryotic community and metabolites found in clay wall material used in the construction of traditional Japanese buildings.

PubMed

Kitajima, Sakihito; Kamei, Kaeko; Nishitani, Maiko; Sato, Hiroyuki

2010-01-01

Clay wall (tsuchikabe in Japanese) material for Japanese traditional buildings is manufactured by fermenting a mixture of clay, sand, and rice straw. The aim of this study was to understand the fermentation process in order to gain insight into the ways waste biomass can be used to produce useful materials. In this study, in addition to Clostridium, we suggested that the family Nectriaceae and the Scutellinia sp. of fungi were important in degrading cell wall materials of rice straw, such as cellulose and/or lignin. The microorganisms in the clay wall material produced sulfur-containing inorganic compounds that may sulfurate minerals in clay particles, and polysaccharides that give viscosity to clay wall material, thus increasing workability for plastering, and possibly giving water-resistance to the dried clay wall.

'Plans are useless'.

PubMed

Bland, Michael

2013-01-01

An essential element in crisis recovery is the protection and/or recovery of reputation. This calls for a crisis communications function that is of more than passing interest to the business continuity specialist and which presents two major challenges in this era of process-driven management: (1) it is an inexact science, more about common sense, psychology, empathy and 'playing it by ear' than about box ticking; (2) it does not lend itself to detailed, rigid plans, although some degree of planning is essential. This paper outlines a flexible approach that will help the crisis team to develop a workable communications plan that strikes a balance between being too detailed and too sketchy. It argues that the whole management team should be involved in developing the plan and sets a number of questions, which, on being answered, will help a realistic, achievable and effective plan to evolve.

From slogans to strategy: a workable approach to customer satisfaction and retention.

PubMed

Timm, P R

1997-01-01

Too many organizations confuse slogans, good intentions, or mechanical phrases with customer service. Most recognize that the most powerful way to prosper in today's economy is to enhance customer satisfaction and loyalty. But customer service has little to do with mottos, slogans, or mechanical phrases. The real management challenge lies in translating the slogans into employee actions that create customer satisfaction and loyalty--in creating a strategy for ensuring good service intentions and exceptional service results. This article shows a logical, theoretically sound approach to building and implementing what I call an E-Plus Customer Satisfaction strategy. Incidentally, I use the term "customer" throughout this article, but I recognize that we have different terms in various organizations. So feel free to substitute "patient", "guest", "client", or any other synonym. The principles are the same.

Quantum Information Science: An Update

NASA Astrophysics Data System (ADS)

Kwek, L. C.; Zen, Freddy P.

2016-08-01

It is now roughly thirty years since the incipient ideas on quantum information science was concretely formalized. Over the last three decades, there has been much development in this field, and at least one technology, namely devices for quantum cryptography, is now commercialized. Yet, the holy grail of a workable quantum computing machine still lies faraway at the horizon. In any case, it took nearly several centuries before the vacuum tubes were invented after the first mechanical calculating were constructed, and several decades later, for the transistor to bring the current computer technology to fruition. In this review, we provide a short survey of the current development and progress in quantum information science. It clearly does not do justice to the amount of work in the past thirty years. Nevertheless, despite the modest attempt, this review hopes to induce younger researchers into this exciting field.

Effects of Using Silica Fume and Polycarboxylate-Type Superplasticizer on Physical Properties of Cementitious Grout Mixtures for Semiflexible Pavement Surfacing

PubMed Central

Karim, Mohamed Rehan; Mahmud, Hilmi; Mashaan, Nuha S.; Katman, Herdayati; Husain, Nadiah Md

2014-01-01

Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-sample t-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout. PMID:24526911

Nuclear weapons are illegal threats

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyrowitz, E.L.

Challenging Harry Almond's position that nuclear deterrence is workable, the author contends that there is no historical basis for believing that anticipation of the horrors of war will be an effective deterrent. He questions the belief that the nuclear balance of terror has maintained the peace for the past 40 years because an arms race is inherently unstable. The argument that the pursuit of national interests takes precedence over any limitation imposed by international law reflects a perception of international law that is comparable to the Third Reich. The bases for a legal evaluation of the status of nuclear weaponsmore » under international law come from express and implicit treaty provisions, international custom, general principles of international law, judicial decisions, resolutions at the United Nations, and the opinions of qualified jurists as well as military necessity.« less

[An application of low-invasive access in ultrasound-guided surgery of liquid formation of the abdominal cavity and retroperitoneal space].

PubMed

Demin, D B; Laĭkov, A V; Funygin, M S; Chegodaeva, A A; Solodov, Iu Iu; Butina, K V

2014-01-01

The article presents a low-invasive method in the intraoperative ultrasound-guided surgery. The method had several steps: an access (2-3 cm) was made to a liquid formation with the following aspiration of contents, a necrotic detritus was removed through the wound tract using simultaneous ultrasound examination of efficacy of emptying the cavity with drainage. This means allowed the performance of single-stage sanitization and drainage of cavity formations, which contained the liquid and dense necrotic tissues in the lumen. The method was effective, technically workable in any surgical hospital. At the same time, it was economically reasonable, because there wasn't need to buy an additional equipment. The application of the means considerably shortened a hospital stay and the lethality was reduced.

Lupus community panel proposals for optimising clinical trials: 2018

PubMed Central

Merrill, Joan T; Manzi, Susan; Aranow, Cynthia; Askenase, Anca; Bruce, Ian; Chakravarty, Eliza; Chong, Ben; Costenbader, Karen; Dall’Era, Maria; Ginzler, Ellen; Hanrahan, Leslie; Kalunian, Ken; Merola, Joseph; Raymond, Sandra; Rovin, Brad; Saxena, Amit; Werth, Victoria P

2018-01-01

Formidable impediments stand in the way of treatment development for lupus. These include the unwieldy size of current trials, international competition for scarce patients, complex outcome measures and a poor understanding of these outcomes in the world at large. The heterogeneity of the disease itself coupled to superimposition of variegated background polypharmacy has created enough immunological noise to virtually ensure the failure of lupus treatment trials, leaving an understandable suspicion that at least some of the results in testing failed drugs over the years may not have been negative, but merely uninterpretable. The authors have consulted with many clinical trial investigators, biopharmaceutical developers and stakeholders from government and voluntary sectors. This paper examines the available evidence that supports workable trial designs and proposes approaches to improve the odds of completing interpretable treatment development programs for lupus. PMID:29657738

Active porous transition towards spatiotemporal control of molecular flow in a crystal membrane

NASA Astrophysics Data System (ADS)

Takasaki, Yuichi; Takamizawa, Satoshi

2015-11-01

Fluidic control is an essential technology widely found in processes such as flood control in land irrigation and cell metabolism in biological tissues. In any fluidic control system, valve function is the key mechanism used to actively regulate flow and miniaturization of fluidic regulation with precise workability will be particularly vital in the development of microfluidic control. The concept of crystal engineering is alternative to processing technology in microstructure construction, as the ultimate microfluidic devices must provide molecular level control. Consequently, microporous crystals can instantly be converted to microfluidic devices if introduced in an active transformability of porous structure and geometry. Here we show that the introduction of a stress-induced martensitic transition mechanism converts a microporous molecular crystal into an active fluidic device with spatiotemporal molecular flow controllability through mechanical reorientation of subnanometre channels.

A 15,000-hour cyclic endurance test of an 8-centimeter-diameter electron bombardment mercury ion thruster

NASA Technical Reports Server (NTRS)

Nakanishi, S.

1976-01-01

A laboratory model 8-cm thruster with improvements to minimize ion chamber erosion and peeling of sputtered metal was subjected to a cyclic endurance test for 15,040 hours and 460 restarts. A charted history of several thruster operating variables and off-normal events are shown in 600-hour segments at three points in the test. The transient behavior of these variables during a typical start-stop cycle is presented. Performance and operating characteristics were nearly constant throughout the test except for a change in the accelerator back-streaming limit. Findings of the post-test inspection confirmed most of the expected results. Charge-exchange ions caused normal accelerator grid erosion. The workability of the various design features have been substantiated, and attainable improvements in propellant utilization efficiency should significantly reduce accelerator erosion.

Job boredom and its correlates in 87 Finnish organizations.

PubMed

Harju, Lotta; Hakanen, Jari J; Schaufeli, Wilmar B

2014-09-01

To investigate the correlates of job boredom in 87 Finnish workplaces (N = 11,468) and to examine the associations between job boredom, health outcomes, and job attitudes. We applied the Dutch Boredom Scale to measure job boredom. Hierarchical logistic regression analysis and odds ratio estimates were used for further examination of the variables. Male, under-36-year-old employees and employees working in transportation, manufacturing, arts, recreation, and entertainment experienced the most job boredom. Job boredom increased the likelihood of employees' turnover and early retirement intentions, poor self-rated health, poor workability, and stress symptoms. Job boredom is a phenomenon that concerns a wide range of industries. We found a clear association between job boredom and negative health- and work-related perceptions. The results support the notion that job boredom can be harmful to employee health.

Design, Development and Testing of Airplanes for Mars Exploration

NASA Technical Reports Server (NTRS)

Hall, David W.

2004-01-01

The opportunity for a piggyback mission to Mars aboard an Ariane 5 rocket in the early spring of 1999 set off feverish design activity at several NASA centers. This report describes the contract work done by faculty, students, and consultants at the California Polytechnic State University in San Luis Obispo California (Cal poly/SLO) to support the NASA/Ames design, construction and test efforts to develop a simple and robust Mars Flyer configuration capable of performing a practical science mission on Mars. The first sections will address the conceptual design of a workable Mars Flyer configuration which started in the spring and summer of 1999. The following sections will focus on construction and flight test of two full-scale vehicles. The final section will reflect on the overall effort and make recommendations for future work.

Protective coping: a grounded theory of educative interactions in palliative care nursing.

PubMed

Morgan, A

2001-02-01

The development of a workable caring partnership in palliative care between the nurse, patient and informal carer is contingent upon the nurse's use of effective interactions that will not only inform, but also help individuals to work towards common beneficial goals. This article summarizes a research project undertaken in Western Australia, which examined the symbolic nature and characteristics of educative interactions. Their therapeutic value was interpreted in order to construct a theory, which in turn, explained their function. Protective coping, which deals with overcoming or minimizing stressors to the individual, has been identified as a basic social interactional process that is fundamental to the optimization of patients' well being during terminal illness care. An understanding of the knowledge-power relationship in palliative care is crucial if subsequent educative outcomes are to be positively influenced.

Experiences with Cray multi-tasking

NASA Technical Reports Server (NTRS)

Miya, E. N.

1985-01-01

The issues involved in modifying an existing code for multitasking is explored. They include Cray extensions to FORTRAN, an examination of the application code under study, designing workable modifications, specific code modifications to the VAX and Cray versions, performance, and efficiency results. The finished product is a faster, fully synchronous, parallel version of the original program. A production program is partitioned by hand to run on two CPUs. Loop splitting multitasks three key subroutines. Simply dividing subroutine data and control structure down the middle of a subroutine is not safe. Simple division produces results that are inconsistent with uniprocessor runs. The safest way to partition the code is to transfer one block of loops at a time and check the results of each on a test case. Other issues include debugging and performance. Task startup and maintenance (e.g., synchronization) are potentially expensive.

Visual display aid for orbital maneuvering - Experimental evaluation

NASA Technical Reports Server (NTRS)

Grunwald, Arthur J.; Ellis, Stephen R.

1993-01-01

An interactive proximity operations planning system, which allows on-site planning of fuel-efficient, multiburn maneuvers in a potential multispacecraft environment, has been experimentally evaluated. An experiment has been carried out in which nonastronaut operators with brief initial training were required to plan a trajectory to retrieve an object accidentally separated from a dual-keel Space Station, for a variety of different orbital situations. The experiments have shown that these operators were able to plan workable trajectories, satisfying a number of operational constraints. Fuel use and planning time were strongly correlated, both with the angle at which the object was separated and with the existence of spatial constraints. Planning behavior was found to be strongly operator-dependent. This finding calls for the need for standardizing planning strategies through operator training or the use of semiautomated planning schemes.

The use of by-products from metallurgical and mineral industries as filler in cement-based materials.

PubMed

Moosberg, Helena; Lagerblad, Björn; Forssberg, Eric

2003-02-01

This investigation has been made in order to make it possible to increase the use of by-products in cement-based materials. Use of by-products requires a screening procedure that will reliably determine their impact on concrete. A test procedure was developed. The most important properties were considered to be strength development, shrinkage, expansion and workability. The methods used were calorimetry, flow table tests, F-shape measurements, measurements of compressive and flexural strength and shrinkage/expansion measurements. Scanning electron microscopy was used to verify some results. Twelve by-products were collected from Swedish metallurgical and mineral industries and classified according to the test procedure. The investigation showed that the test procedure clearly screened out the materials that can be used in the production of concrete from the unsuitable ones.

Measuring the efficiency of a healthcare waste management system in Serbia with data envelopment analysis.

PubMed

Ratkovic, Branislava; Andrejic, Milan; Vidovic, Milorad

2012-06-01

In 2007, the Serbian Ministry of Health initiated specific activities towards establishing a workable model based on the existing administrative framework, which corresponds to the needs of healthcare waste management throughout Serbia. The objective of this research was to identify the reforms carried out and their outcomes by estimating the efficiencies of a sample of 35 healthcare facilities engaged in the process of collection and treatment of healthcare waste, using data envelopment analysis. Twenty-one (60%) of the 35 healthcare facilities analysed were found to be technically inefficient, with an average level of inefficiency of 13%. This fact indicates deficiencies in the process of collection and treatment of healthcare waste and the information obtained and presented in this paper could be used for further improvement and development of healthcare waste management in Serbia.

Magnetic resonance image segmentation using multifractal techniques

NASA Astrophysics Data System (ADS)

Yu, Yue-e.; Wang, Fang; Liu, Li-lin

2015-11-01

In order to delineate target region for magnetic resonance image (MRI) with diseases, the classical multifractal spectrum (MFS)-segmentation method and latest multifractal detrended fluctuation spectrum (MF-DFS)-based segmentation method are employed in our study. One of our main conclusions from experiments is that both of the two multifractal-based methods are workable for handling MRIs. The best result is obtained by MF-DFS-based method using Lh10 as local characteristic. The anti-noises experiments also suppot the conclusion. This interest finding shows that the features can be better represented by the strong fluctuations instead of the weak fluctuations for the MRIs. By comparing the multifractal nature between lesion and non-lesion area on the basis of the segmentation results, an interest finding is that the gray value's fluctuation in lesion area is much severer than that in non-lesion area.

Numerical marching techniques for fluid flows with heat transfer

NASA Technical Reports Server (NTRS)

Hornbeck, R. W.

1973-01-01

The finite difference formulation and method of solution is presented for a wide variety of fluid flow problems with associated heat transfer. Only a few direct results from these formulations are given as examples, since the book is intended primarily to serve a discussion of the techniques and as a starting point for further investigations; however, the formulations are sufficiently complete that a workable computer program may be written from them. In the appendixes a number of topics are discussed which are of interest with respect to the finite difference equations presented. These include a very rapid method for solving certain sets of linear algebraic equations, a discussion of numerical stability, the inherent error in flow rate for confined flow problems, and a method for obtaining high accuracy with a relatively small number of mesh points.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bodnarczuk, M.

How does one assure that both quality and creativity are obtained in basic research environments QA theoreticians have attempted to develop workable definitions of quality, but in more reflective moments, these definitions often fail to capture the deeper essence of the idea of quality.'' This paper asserts that creativity (as a product of the human mind) is a concrete interface between perfunctory definitions of quality (conformance to specifications) and more philosophical speculations about the nature of quality- related ultimates'' like elegance or beauty. In addition, we describe the distinction between creative ideas and creative acts and highlight one of themore » major inhibitors of creativity, fear. Finally we show that highly creative people often have an irreverent attitude toward boundaries and established authority, and discuss how one can allow for this when designing a QA program in a basic research environment.« less

Single point incremental forming: Formability of PC sheets

NASA Astrophysics Data System (ADS)

Formisano, A.; Boccarusso, L.; Carrino, L.; Lambiase, F.; Minutolo, F. Memola Capece

2018-05-01

Recent research on Single Point Incremental Forming of polymers has slightly covered the possibility of expanding the materials capability window of this flexible forming process beyond metals, by demonstrating the workability of thermoplastic polymers at room temperature. Given the different behaviour of polymers compared to metals, different aspects need to be deepened to better understand the behaviour of these materials when incrementally formed. Thus, the aim of the work is to investigate the formability of incrementally formed polycarbonate thin sheets. To this end, an experimental investigation at room temperature was conducted involving formability tests; varying wall angle cone and pyramid frusta were manufactured by processing polycarbonate sheets with different thicknesses and using tools with different diameters, in order to draw conclusions on the formability of polymer sheets through the evaluation of the forming angles and the observation of the failure mechanisms.

"Physics Stories": How the Early Technologies of High Voltage and High Vacuum Led to "Modern Physics"

NASA Astrophysics Data System (ADS)

Greenslade, Thomas B.

2018-05-01

Some of you may remember the 1979 television series "Connections" that was written and narrated by James Burke, a British science writer. Burke's technique was to choose a number of seemingly unrelated ideas and show how they led to developments in science and technology. This is an enjoyable business, even if some of the connections seem to be stretched at times, and led to a book by Burke. In a number of talks that I have given over the years, I have made somewhat less fanciful connections that suggest how the technologies of high vacuum and high voltage led to what used to be called "modern physics." Today we might limit the "modern" era to the years from 1890 to 1920 that gave the first workable theories of small-scale physics.

Practical experiences with new types of highly modified asphalt binders

NASA Astrophysics Data System (ADS)

Špaček, Petr; Hegr, Zdeněk; Beneš, Jan

2017-09-01

As a result of steadily increasing traffic load on the roads in the Czech Republic, we should be focused on the innovative technical solutions, which will lead to extending the life time of asphalt pavements. One of these ways could be the future use of bitumen with a higher degree of polymer modification. This paper discusses experience with comparison of new highly polymer modified asphalt binder type with conventional polymer modified asphalt binder and unmodified binder with penetration grade 50/70. There are compared the results of various types laboratory tests of asphalt binders, as well as the results of asphalt mixtures laboratory tests. The paper also mentions the experience with workability and compactability of asphalt mixture with highly polymer modified asphalt binder during the realization of the experimental reference road section by the Skanska company in the Czech Republic.

Effects of using silica fume and polycarboxylate-type superplasticizer on physical properties of cementitious grout mixtures for semiflexible pavement surfacing.

PubMed

Koting, Suhana; Karim, Mohamed Rehan; Mahmud, Hilmi; Mashaan, Nuha S; Ibrahim, Mohd Rasdan; Katman, Herdayati; Husain, Nadiah Md

2014-01-01

Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-sample t-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout.

Managed Entry Agreements for Pharmaceuticals in the Context of Adaptive Pathways in Europe

PubMed Central

Bouvy, Jacoline C.; Sapede, Claudine; Garner, Sarah

2018-01-01

As per the EMA definition, adaptive pathways is a scientific concept for the development of medicines which seeks to facilitate patient access to promising medicines addressing high unmet need through a prospectively planned approach in a sustainable way. This review reports the findings of activities undertaken by the ADAPT-SMART consortium to identify enablers and explore the suitability of managed entry agreements for adaptive pathways products in Europe. We found that during 2006–2016 outcomes-based managed entry agreements were not commonly used for products with a conditional marketing authorization or authorized under exceptional circumstances. The barriers and enablers to develop workable managed entry agreements models for adaptive pathways products were discussed through interviews and a multi-stakeholder workshop with a number of recommendations made in this paper. PMID:29636692