Pharmacokinetics and efficiency of brain targeting of ginsenosides Rg1 and Rb1 given as Nao-Qing microemulsion.

PubMed

Li, Tao; Shu, Ya-Jun; Cheng, Jia-Yin; Liang, Run-Cheng; Dian, Shao-Na; Lv, Xiao-Xun; Yang, Meng-Qi; Huang, Shu-Ling; Chen, Gang; Yang, Fan

2015-02-01

Nao-Qing solution has been shown to be clinically effective in the treatment of acute ischemic stroke (AIS). The purpose of this study was to improve the pharmacokinetics and brain uptake of Nao-Qing, administered as an oil-in-water microemulsion. Sprague-Dawley (SD) rats were given Nao-Qing microemulsion by intranasal or intragastric routes. Samples of blood, brain, heart, liver, lung and kidney were collected at pre-determined time intervals, and the contents of ginsenosides Rg1 and Rb1 (active ingredients of the Nao-Qing microemulsion) were analyzed by high-performance liquid chromatography (HPLC). The results showed that contents of ginsenosides Rg1 and Rb1 in Nao-Qing microemulsion was 8475.13 ± 54.61 μg/ml and 6633.42 ± 527.27 μg/ml, respectively, and that the particle size, pH and viscosity of the microemulsion were 19.9 ± 5.07 nm, 6.1 and 3.056 × 10(-3 )Pas, respectively. Absorption of ginsenoside Rg1 was higher than that of ginsenoside Rb1, which was barely detectable after intragastric administration; furthermore, the concentration of ginsenoside Rg1 in blood and other tissues at each time point was lower for intragastric than for intranasal administration. Compared with intragastric administration, intranasal administration resulted in a shorter tmax (0.08 versus 1 h), a higher Cmax (16.65 versus 11.29 μg/ml), and a higher area under the concentration-time curve (AUC) (592.91 versus 101.70 μgċh/ml) in the brain. The relative rates of uptake (Re) and the ratio of peak concentration (Ce) in the brain were 126.31% and 147.48% for ginsenoside Rg1, respectively. These data illustrate that intranasal administration can promote the absorption of drugs in Nao-Qing microemulsion and achieve fast effect.

"To Feel at Home in the Wonderful World of Modern Science": New Chinese Historiography and Qing Intellectual History.

PubMed

Sela, Ori

2017-09-01

Argument In recent decades a large body of scholarship on the first half of twentieth-century China has successfully shown the ways in which history and historiography had been constructed at the time, as well as the links between history, national identity, education, and politics that was forged during this period. In this paper, I examine Qing intellectual history, in particular that of the mid or "High Qing." I discuss the development of the historiography of this field in the early twentieth century by drawing on the larger developments in historiography; by demonstrating how these developments had shaped Qing intellectual history for later times; by focusing on the historical actors' sense of the importance of "science," being "scientific," and "modernization"; and, by unraveling the intimate connections to older historiographical narratives going back all the way to the eighteenth and nineteenth centuries.

Colitis with wall thickening and edematous changes during oral administration of the powdered form of Qing-dai in patients with ulcerative colitis: a report of two cases.

PubMed

Kondo, Satoru; Araki, Toshimitsu; Okita, Yoshiki; Yamamoto, Akira; Hamada, Yasuhiko; Katsurahara, Masaki; Horiki, Noriyuki; Nakamura, Misaki; Shimoyama, Takahiro; Yamamoto, Takayuki; Takei, Yoshiyuki; Kusunoki, Masato

2018-03-16

Orally administered Qing-dai, called indigo naturalis in Latin, is reportedly useful for the treatment of ulcerative colitis. We herein describe two patients with ulcerative colitis who developed colitis with wall thickening and edematous changes during oral administration of the powdered form of Qing-dai. In Case 1, a 35-year-old man developed colitis similar to ischemic colitis with bloody stool that recurred each time he ingested Qing-dai. He had no signs of recurrence upon withdrawal of Qing-dai. In Case 2, a 43-year-old woman underwent ileocecal resection for treatment of an intussusception 2 months after beginning oral administration of Qing-dai. Edema and congestion but no ulceration were present in the mucosa of the resected specimen. Both patients exhibited abdominal pain with bloody diarrhea, and abdominal computed tomography showed marked wall edema affecting an extensive portion of the large bowel.

[Contention on the theory of processing techniques of Chinese materia medica in the Ming-Qing period].

PubMed

Chen, Bin; Jia, Tianzhu

2015-03-01

On the basis of the golden stage of development of processing techniques of medicinals in the Song dynasty, the theory and techniques of processing in the Ming-Qing dynasties developed and accomplished further. The knowledge of some physicians on the processing of common medicinal, such as Radix rehmannia and Radixophiopogonis, was questioned, with new idea of processing methods put forward and argued against those insisting traditional ones, marking the progress of the art of processing. By reviewing the contention of technical theory of medicinal processing in the Ming-Qing period, useful references can be provided for the inheritance and development of the traditional art of processing medicinals.

The Rise of Women's Modern Schooling in Late Qing China (1840-1911)

ERIC Educational Resources Information Center

Liu, Xiaoyi

2009-01-01

The rise of women's modern schooling in late Qing China was deemed to be, by the historical trend of modern China, a progress that coincided with China's modernization and national self-strengthening movement after the humiliating defeat of the Opium War. This article is an examination of this process from 1840 to 1911, which had undergone three…

Pharmacokinetics and disposition of monoterpene glycosides derived from Paeonia lactiflora roots (Chishao) after intravenous dosing of antiseptic XueBiJing injection in human subjects and rats.

PubMed

Cheng, Chen; Lin, Jia-zhen; Li, Li; Yang, Jun-ling; Jia, Wei-wei; Huang, Yu-hong; Du, Fei-fei; Wang, Feng-qing; Li, Mei-juan; Li, Yan-fen; Xu, Fang; Zhang, Na-ting; Olaleye, Olajide E; Sun, Yan; Li, Jian; Sun, Chang-hai; Zhang, Gui-ping; Li, Chuan

2016-04-01

Monoterpene glycosides derived from Paeonia lactiflora roots (Chishao) are believed to be pharmacologically important for the antiseptic herbal injection XueBiJing. This study was designed to characterize the pharmacokinetics and disposition of monoterpene glycosides. Systemic exposure to Chishao monoterpene glycosides was assessed in human subjects receiving an intravenous infusion and multiple infusions of XueBiJing injection, followed by assessment of the pharmacokinetics of the major circulating compounds. Supportive rat studies were also performed. Membrane permeability and plasma-protein binding were assessed in vitro. A total of 18 monoterpene glycosides were detected in XueBiJing injection (content levels, 0.001-2.47 mmol/L), and paeoniflorin accounted for 85.5% of the total dose of monoterpene glycosides detected. In human subjects, unchanged paeoniflorin exhibited considerable levels of systemic exposure with elimination half-lives of 1.2-1.3 h; no significant metabolite was detected. Oxypaeoniflorin and albiflorin exhibited low exposure levels, and the remaining minor monoterpene glycosides were negligible or undetected. Glomerular-filtration-based renal excretion was the major elimination pathway of paeoniflorin, which was poorly bound to plasma protein. In rats, the systemic exposure level of paeoniflorin increased proportionally as the dose was increased. Rat lung, heart, and liver exposure levels of paeoniflorin were lower than the plasma level, with the exception of the kidney level, which was 4.3-fold greater than the plasma level; brain penetration was limited by the poor membrane permeability. Due to its significant systemic exposure and appropriate pharmacokinetic profile, as well as previously reported antiseptic properties, paeoniflorin is a promising XueBiJing constituent of therapeutic importance.

The administration of Sheng Hua Tang immediately after delivery to reduce the incidence of retained placenta in Holstein dairy cows.

PubMed

Cui, Dongan; Wang, Xuezhi; Wang, Lei; Wang, Xurong; Zhang, Jingyan; Qin, Zhe; Li, Jianxi; Yang, Zhiqiang

2014-03-15

Sheng Hua Tang, a classical herbal formula consisting of Radix Angelicae sinensis, Ligustici rhizoma, Semen persicae, Zingiberis rhizoma, and Radix glycyrrhizae, is known to be beneficial in alleviating postpartum diseases and facilitating a return to normal reproductive function. This study investigated whether the administration of Sheng Hua Tang within 2 to 4 hours after delivery was effective as a preventive treatment for reducing the risk of retained placenta in Holstein dairy cows. A total of 357 cows, each of which had delivered its calf spontaneously, were randomly allocated to one of two groups. In the treatment group, the cows (n = 175) received Sheng Hua Tang with an oral dose of 0.36 g crude herb per kg·body weight once daily for three consecutive days. The controls (n = 182) received no treatment. The placental retention proportion was 4.0% and 17.0% within 12 hours after delivery in the treated and control animals, respectively (P < 0.01). We found decreases in the calving-to-first-service interval (73.2 ± 25.1 vs. 81.9 ± 32.8 days; P < 0.01), calving-to-conception interval (93.4 ± 38.8 vs. 114.6 ± 42.9 days; P < 0.01), and service per conception (1.5 ± 0.8 vs. 1.9 ± 1.0 days; P < 0.01) in the treatment group compared with the control group. The first artificial insemination conception proportion was higher in the treatment group than in the control group (60.4% vs. 41.1%; P = 0.01). Moreover, the between-group difference in the proportion of cows that were pregnant within 180 days postpartum approached statistical significance (88.2% vs. 80.6%; P = 0.07). Sheng Hua Tang showed beneficial effects in reducing the incidence of retained placenta and improving subsequent reproductive performance in cows. This preventive treatment strategy would be effective in improving the management of puerperal health. The potential benefits of Sheng Hua Tang warrant further investigation to determine whether this preventive treatment strategy can be endorsed as

Traditional Chinese Medicine Induced Liver Injury

PubMed Central

2014-01-01

Traditional Chinese Medicine (TCM) is popular around the world and encompasses many different practices with particular emphasis on herbal TCM. Using the PubMed database, a literature search was undertaken to assess the extent herbal TCM products exert rare hepatotoxicity. Analysis of reported cases revealed numerous specified herbal TCM products with potential hepatotoxicity. Among these were An Shu Ling, Bai Fang, Bai Xian Pi, Ban Tu Wan, Bo He, Bo Ye Qing Niu Dan, Bofu Tsu Sho San, Boh Gol Zhee, Cang Er Zi, Chai Hu, Chaso, Chi R Yun, Chuan Lian Zi, Ci Wu Jia, Da Chai Hu Tang, Da Huang, Du Huo, Gan Cao, Ge Gen, Ho Shou Wu, Hu Bohe You, Hu Zhang, Huang Qin, Huang Yao Zi, Hwang Geun Cho, Ji Gu Cao, Ji Ji, Ji Xue Cao, Jiguja, Jin Bu Huan, Jue Ming Zi, Kamishoyosan, Kudzu, Lei Gong Teng, Long Dan Xie Gan Tang, Lu Cha, Ma Huang, Mao Guo Tian Jie Cai, Onshido, Polygonum multiflorum, Qian Li Guang, Ren Shen, Sairei To, Shan Chi, Shen Min, Shi Can, Shi Liu Pi, Shou Wu Pian, Tian Hua Fen, White flood, Wu Bei Zi, Xi Shu, Xiao Chai Hu Tang, Yin Chen Hao, Zexie, Zhen Chu Cao, and various unclassified Chinese herbal mixtures. Causality was firmly established for a number of herbal TCM products by a positive reexposure test result, the liver specific scale of CIOMS (Council for International Organizations of Medical Sciences), or both. Otherwise, the quality of case data was mixed, especially regarding analysis of the herb ingredients because of adulteration with synthetic drugs, contamination with heavy metals, and misidentification. In addition, non-herbal TCM elements derived from Agaricus blazei, Agkistrodon, Antelope, Bombyx, Carp, Fish gallbladder, Phellinus, Scolopendra, Scorpio, and Zaocys are also known or potential hepatotoxins. For some patients, the clinical course was severe, with risks for acute liver failure, liver transplantation requirement, and lethality. In conclusion, the use of few herbal TCM products may rarely be associated with hepatotoxicity in some

[A brief investigation on Gu Dehua, a female healer from Wuzhong in the Qing Dynasty].

PubMed

Lin, Z K; Song, W J

2016-09-28

The female healer is a special community in traditional Chinese medical professionals. Since the Song-Yuan Dynasties, although the literati class holding the social voices and the male healers acting as medical orthodoxy were always suspicious of the female healers' behaviors and their medical morality, and tarnished their images through all kinds of media. Meanwhile, the female healers were still badly needed on the account of recognition of distinction between sexes between both sexes due to the rising of neo-Confucianism. An excellent female healer could still earn wide respect from the society. Gu Dehua was a famous female healer from Wuzhong in the Qing Dynasty's Daoguang-Xianfeng period. By investigating Gu Delua's family conditions, deeds and works, and her career, the community of the female healers in the Ming-Qing Dynasties can be thus understood.

Determine the Role of Canonical Wnt Signaling in Ovarian Tumorigenesis

DTIC Science & Technology

2011-10-01

oncogenic Ras. Nature, 2000. 406(6792): p. 207-10. 11 16. Kuilman, T., et al., The essence of senescence. Genes Dev, 2010. 24(22): p. 2463- 79. 17...Benjamin G. Bitler, Jasmine P. Nicodemus, Hua Li, et al. Senescence Wnt5a Suppresses Epithelial Ovarian Cancer by Promoting Cellular...Suppresses Epithelial Ovarian Cancer by Promoting Cellular Senescence Benjamin G. Bitler1, Jasmine P. Nicodemus1, Hua Li1, Qi Cai2, Hong Wu3, Xiang

A Primary Study on the Recording Method of Interior Decoration in Qing Dynasty - A Case Study of Interior Decoration of Jingfu Palace

NASA Astrophysics Data System (ADS)

Rong, X.; He, B.; Zhuang, L.

2017-08-01

The existing interior decoration of Qing Dynasty is the master of that of each dynasty, with its diversified forms and complicated functions. As early as 1920s, the Rehabilitation Committee of Qing court recorded the interior furnishing in the Forbidden City by using Chinese traditional documentary method. Today, along with the constantly updated techniques, the recording method for the current situation of interior decoration has gradually developed from two-dimensional drawings into digital and comprehensive record. However, the current research results are mostly limited to a single field. This paper takes the digital record and reproduction about the current situation of interior decoration in Jingfu Palace in the Forbidden City as an example. Through the use of photogrammetry, 3D laser scanning, virtual display and other technology and equipment at the forefront of architectural field, it makes qualitative and quantitative record about the interior decoration inside Jingfu Palace. By combing with the interpretation of historical documents, it restores the original design ideas hidden behind the current situation of interior decoration, so as to summarize the best recording and reproducing method of interior decoration of Qing Dynasty.

Renewable Energy in China: Xiao Qing Dao Village Power Wind/Diesel Hybrid Pilot Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2006-01-01

In 2000, DOE/NREL and the State Power Corporation of China (SPCC) developed a pilot project to electrify Xiao Qing Dao, a small island located in China's Yellow Sea. The project demonstrates the practicality of renewable energy systems for medium-scale, off-grid applications. It consists of four 10 k-W wind turbines connected to a 30-kW diesel generator, a 40-kW inverter and a battery bank.

Electronic structure of the ingredient planes of Bi2Sr2CaCu2O8 + δ and Bi2Sr2CuO6 + δ superconductors

NASA Astrophysics Data System (ADS)

Ma, Xucun

Understanding the mechanism of high transition temperature superconductivity in cuprates has been hindered by the apparent complexity of their multilayered crystal structure. Using a cryogenic scanning tunneling microscopy (STM), we report on layer-by-layer probing of the electronic structures of the ingredient planes (BiO, SrO, CuO2) of Bi2Sr2CaCu2O8 + δ (Bi-2212) and Bi2Sr2CuO6 + δ (Bi-2201) superconductors prepared by argon-ion bombardment and annealing (IBA) technique. We show that the well-known pseudogap (PG) feature observed by STM is inherently a property of the charge reservoir planes and thus irrelevant directly to Cooper pairing. The CuO2 planes are exclusively characterized by a small gap inside the PG. The small gap becomes invisible near Tc, which we identify as the superconducting gap. The results constitute severe constraints on any microscopic model for high Tc superconductivity in cuprates. Contributors: Yan-Feng Lv, Wen-Lin Wang, Hao Ding, Yang Wang, Yong Zhong, Ying Ding, Ruidan Zhong, John Schneeloch, Gen-Da Gu, Lili Wang, Ke He, Shuai-Hua Ji, Lin Zhao, Xing-Jiang Zhou Can-Li Song, and Qi-Kun Xue. NSF and MOST of China.

Introduction: Paving the Old-New Way from Qing to China.

PubMed

Sela, Ori

2017-09-01

The funeral procession of Sheng Xuanhuai (, 1844-1916) - the renowned Qing scholar-official, financier, and "father of Chinese industrialism" - meandered through the streets of Shanghai on 18 November 1917. The funeral was a grand event, one that was purportedly documented in film, later to be distributed as the first "news short-film" () in China. The North China Herald reported on the event in some detail, at times in rather florid language, and suggested that "the cortege was splendid and impressive, bringing back the days of the Manchu emperors. The ceremonial costumes, the musical instruments and much more of the accoutrements dated back to the days of the Empire" ("Sheng Kung-pao's Funeral," 1917, 467-68). And indeed, the procession included a variety of ritual customs and insignia from Qing (1644-1911) times: imperial banners, ancestral tablets, Buddhist and Daoist priests, paper artifacts, and much more. Simultaneously, nonetheless, other kinds of participants and objects - new and not of imperial pedigree - were part of and intermixed with the older materials: certificates of rank were carried on cars; boy scouts and college students marched alongside the priests; many of the participants arrived by train (mainly from Sheng's hometown, Suzhou); and as the Shanghai portion of the procession ended, it continued by steamer to Suzhou. The conclusion of the North China Herald account, however, seems to have emphasized a dichotomy of old and new rather than a joyful mix of the two: Hundreds of men, dressed in the ancient costume of the old dynasties, bore a strong contrast to the eight behind them, sons of intimate friends of the deceased. They were on horseback and wore high silk hats, frock coats and white breeches tucked in riding boots. Truly the passing of the old and the entering of the new. (Ibid.; emphasis added) This view - the old giving way to the new - was not just an off-hand (Western) journalistic analysis; it was part of a larger discourse about

Comparative analysis of the main bioactive components of Xin-Sheng-Hua granule and its single herbs by ultrahigh performance liquid chromatography with tandem mass spectrometry.

PubMed

Pang, Hanqing; Wang, Jun; Tang, Yuping; Xu, Huiqin; Wu, Liang; Jin, Yi; Zhu, Zhenhua; Guo, Sheng; Shi, Xuqin; Huang, Shengliang; Sun, Dazheng; Duan, Jin-Ao

2016-11-01

Xin-Sheng-Hua granule, a representative formula for postpartum hemorrhage, has been used clinically to treat postpartum diseases. Its main bioactive components comprise aromatic acids, phthalides, alkaloids, flavonoids, and gingerols among others. To investigate the changes in main bioactive constituents in its seven single herbs before and after compatibility, a rapid, simple, and sensitive method was developed for comparative analysis of 27 main bioactive components by using ultrahigh-performance liquid chromatography with triple quadrupole electrospray tandem mass spectrometry for the first time. The sufficient separation of 27 target constituents was achieved on a Thermo Scientific Hypersil GOLD column (100 mm × 3 mm, 1.9 μm) within 20 min under the optimized chromatographic conditions. Compared with the theoretical content, the observed content of each analyte showed remarkable differences in Xin-Sheng-Hua granule except thymine, p-coumaric acid, senkyunolide I, senkyunolide H, and ligustilide; the total contents of 27 components increased significantly, and the content variation degrees for the different components were gingerols > flavonoids > aromatic acids > alkaloids > phthalides. The results could provide a good reference for the quality control of Xin-Sheng-Hua granule and might be helpful to interpret the drug interactions based on variation of bioactive components in formulae. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[The affinity between Le family of Tong Ren Tang and acu-moxibustion as viewed from Mian xue tang zhen jiu ji cheng (Mian Xuetang's Synthetic Work of Acu-moxibustion)].

PubMed

Huang, L X

2017-11-28

This compilation process of Mian xue tang zhen jiu ji cheng ( Mian Xuetang ' s Synthetic Work of Acu - moxibustion )was quite mysterious, the book's advent coincidentally met with several major historical events which made its value of decoding its historical functions far beyond its academic value. The editor of this book is Le Xianyang, the founder of Tong Ren Tang. While compiling this book, he also made a replica of Ming-Dynasty's Zhengtong bronze statue. More than 200 years later, Le Jingyu, the 12th generation of the Le family revised Ming Tang Tu inherited from his ancestors and engraved Ming Tang Tu on the stone for its standardization. This great achievement of Le family was no less than the recasting of the Tiansheng bronze statue and the reengraving Tong ren shu xue zhen jiu tu jing ( Illustrated Manual of Acupuncture Points of the Bronze Figure ) by support of state power for building the Beijing Imperial Hospital in the eighth year of the Zhengtong reign (1443).

RETRACTED: Relationship between the ACE I/D gene polymorphism and T1DN susceptibility/risk of T1DM developing into T1DN in the Caucasian population.

PubMed

Zhou, Tian-Biao; Guo, Xue-Feng; Jiang, Zongpei; Li, Hong-Yan

2015-12-01

26, 2015 doi: 10.1177/1470320314566019 Tian-Biao Zhou, Xue-Feng Guo, Zongpei Jiang, and Hong-Yan Li Relationship between the ACE I/D gene polymorphism and T1DN susceptibility/risk of T1DM developing into T1DN in the Caucasian population Journal of Renin-Angiotensin-Aldosterone System 1470320314563425, first published on February 1, 2015 doi: 10.1177/1470320314563425 Chun-Hua Yang and Tian-Biao Zhou Relationship between the angiotensinogen A1166C gene polymorphism and the risk of diabetes mellitus developing into diabetic nephropathy Journal of Renin-Angiotensin-Aldosterone System 1470320314566221, first published on February 1, 2015 doi: 10.1177/1470320314566221 Chun-Hua Yang and Tian-Biao Zhou Association of the ACE I/D gene polymorphism with sepsis susceptibility and sepsis progression Journal of Renin-Angiotensin-Aldosterone System 1470320314568521, first published on February 3, 2015 doi: 10.1177/1470320314568521 Articles published in an issue Guohui Liu, Tian-Biao Zhou, Zongpei Jiang, and Dongwen Zheng Association of ACE I/D gene polymorphism with T2DN susceptibility and the risk of T2DM developing into T2DN in a Caucasian population Journal of Renin-Angiotensin-Aldosterone System March 2015 16: 165-171, first published on November 14, 2014 doi: 10.1177/1470320314557849 Weiqiang Zhong, Zhongliang Huang, Yong Wu, Zongpei Jiang, and Tian-Biao Zhou Association of aldosterone synthase (CYP11B2) gene polymorphism with IgA nephropathy risk and progression of IgA nephropathy Journal of Renin-Angiotensin-Aldosterone System September 2015 16: 660-665, first published on August 20, 2014 doi: 10.1177/1470320314524011.

[Chinese books on human anatomy published in the late Qing dynasty].

PubMed

Matsumoto, Hideshi

2007-12-01

Quanti-chanwei (1881) is the first technical book on human anatomy written in Chinese and brought to Modern China. It was compiled and translated on the basis of Anatomy, Descriptive and Surgical (first edition in 1858) by Henry Gray. Quanti-chanwei was published with intent to establish Chinese translations for terms referring to anatomy, and it gained broad support from medical missionaries who mainly served in Guangdong, Shanghai, and Fuzhou at that time. Quanti-tongkao (1886) was also complied and translated on the basis of Gray' Anatomy, Descriptive and Surgical. It was published from Jingshi Tongwen Guan, The Academy of Foreign Languages in the Qing dynasty, and they selected different words for the translation into Chinese from Quanti-chanwei. Thus, although Gray' Anatomy, Descriptive and Surgical played a great role in the introduction of Western Medicine into Modern China, there was no accordance between the national government and the provinces regarding Chinese translations for terms referring to anatomy.

Spin and pseudospin symmetric Dirac particles in the field of Tietz—Hua potential including Coulomb tensor interaction

NASA Astrophysics Data System (ADS)

Sameer, M. Ikhdair; Majid, Hamzavi

2013-09-01

Approximate analytical solutions of the Dirac equation for Tietz—Hua (TH) potential including Coulomb-like tensor (CLT) potential with arbitrary spin—orbit quantum number κ are obtained within the Pekeris approximation scheme to deal with the spin—orbit coupling terms κ(κ ± 1)r-2. Under the exact spin and pseudospin symmetric limitation, bound state energy eigenvalues and associated unnormalized two-component wave functions of the Dirac particle in the field of both attractive and repulsive TH potential with tensor potential are found using the parametric Nikiforov—Uvarov (NU) method. The cases of the Morse oscillator with tensor potential, the generalized Morse oscillator with tensor potential, and the non-relativistic limits have been investigated.

Bibliography of Literature on China’s Glaciers and Permafrost. Part I. 1938-1979.

DTIC Science & Technology

1982-09-01

The Quaternary Period Glaciers of China. Kexue Chubanshe, 1975. Li Chengsan and Guo Lingzhi : Glacier topography at Kangding-bianfu. Dizhi Lunping...Vol. 4, No. 1, 1939. Li Chengsan and Gao Yongyuan: Glacier topography in the Daba Shan at Guangyuan. Dili, Vol. 2, Nos. 1-2, 1942. Guo Lingzhi ...Mountains region. Zhongguo Disiji Yanjiu, Vol. 1, No. 1, 1958. Guo Lingzhi and Xue Yuqun: A discussion of the relationship of the Fen River and the

Ionic liquid and aqueous two-phase extraction based on salting-out coupled with high-performance liquid chromatography for the determination of seven rare ginsenosides in Xue-Sai-Tong injection.

PubMed

Li, Lan-Jie; Jin, Yong-Ri; Wang, Xiao-Zhong; Liu, Ying; Wu, Qian; Shi, Xiao-Lei; Li, Xu-Wen

2015-09-01

A method of ionic liquid salt aqueous two-phase extraction coupled with high-performance liquid chromatography has been developed for the analysis of seven rare ginsenosides including Rg6 , F4 , 20(S)-Rg3 , 20(R)-Rg3 , Rk3 , Rk1 , and Rg5 in Xue-Sai-Tong injection. The injection was mixed with ionic liquid 1-butyl-3-methylimidazolium bromide aqueous solution, and a mixture was obtained. With the addition of sodium dodecyl sulfate and dipotassium phosphate into the mixture, the aqueous two-phase mixture was formed after ultrasonic treatment and centrifuged. Rare ginsenosides were extracted into the upper phase. To obtain a high extraction factors, various influences were considered systematically, such as the volume of ionic liquid, the category and amount of salts, the amount of sodium dodecyl sulfate, the pH value of system, and the time of ultrasonic treatment. Under the optimal condition, rare ginsenosides in Xue-Sai-Tong injection were enriched and detected, the recoveries of seven rare ginsenosides ranged from 90.05 to 112.55%, while relative standard deviations were lower than 2.50%. The developed method was reliable, rapid and sensitive for the determination of seven rare ginsenosides in the injections. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Protective effect of a Chinese Medicine formula He-Ying-Qing-Re Formula on diabetic retinopathy.

PubMed

Wang, Leilei; Wang, Ning; Tan, Hor-yue; Zhang, Yinjian; Feng, Yibin

2015-07-01

He-Ying-Qing-Re Formula (HF) is a formula modified from "Si-Miao-Yong-An Decoction", a traditional Chinese medical classic emerged in the Qing dynasty and has been reported for treatment of vascular diseases. HF, containing 8 herbs, has been used in local hospital for decades as a complementary method for diabetic retinopathy (DR) with retinal vascular dysfunction. Clinical reports revealed HF could ameliorate vision defects, microaneurysms, hemorrhages and macular edema. The aim of this study is to investigate the anti-DR action of HF and its underlying mechanism experimentally. Chromatographic fingerprinting of HF and rodent model of DR were established; hypoglycemic effect of HF was measured by fasting, random blood glucose and glucose tolerance test; vascular degeneration was measured by retinal digestion; blood-retina-barrier (BRB) permeability was assessed with Evans Blue leakage assay. Advanced glycation end products (AGEs) were measured in vitro and in vivo level; Migration of retinal vascular endothelial cells were determined by wound healing and transwell chamber assays; permeability of endothelial monolayer was monitored with dextran transport. AGEs-related proteins and signaling were measured with immunoblotting and immunohistochemistry. Chlorogenic acid, ferulic acid and arctin were identified as major components in HF; HF suppresses retinal vasculature degeneration and BRB permeability damage without significant inhibition on hyperglycemia; HF reduces in vitro and in vivo formation of AGEs and AGEs-induced migration as well as permeability of retinal vascular endothelial cells. Expression of tight junction proteins Zo-1 and Claudin-1 was increased while activation of AGEs receptor and downstream signaling Akt were suppressed upon HF treatment. HF exhibits protective effect against diabetic retinopathy, which may be associated with inhibition on AGEs and recovery on endothelial dysfunction via modulation of tight junction and AGEs downstream signaling

JPRS Report, China Red Flag No 15, 1 August 1987

DTIC Science & Technology

1987-10-07

9-13) (Xiao Ke) • • • • • 1* Consolidate and Develop a New Type of Army-Government and Army-People Relationship (pp 14-17) (Wang Fang, Li Qing...the Socialist Commodity Economy (pp 44-46) ( Li Guangyuan) 78 ’Emotional Investment’ Viewed From Various Angles (p 47) (Lei Ke) 85 Singing the...counted as a setback, but it was precisely during the setback of the great revolution that our Army was founded. During the 25,000- li Long March

Traditional Chinese medicine compound ShengJinRunZaoYangXue granules for treatment of primary Sjögren's syndrome: a randomized, double-blind, placebo-controlled clinical trial.

PubMed

Hu, Wei; Qian, Xian; Guo, Feng; Zhang, Miaojia; Lyu, Chengyin; Tao, Juan; Gao, Zhong'en; Zhou, Zhengqiu

2014-01-01

Traditional Chinese medical treatment of primary Sjögren's syndrome has advantages over Western medicine in terms of fewer side effects and improved patient conditions. This study was a multicenter, randomized, double-blind, placebo-controlled clinical trial of the efficacy and safety of ShengJinRunZaoYangXue granules for the treatment of primary Sjögren's syndrome, including the symptoms of dry mouth and dry eye. We undertook a 6-week, double-blind, randomized trial involving 240 patients with primary Sjögren's syndrome at five centers in East China. A computer-generated randomization schedule assigned patients at a 2:1 ratio to receive either ShengJinRunZaoYangXue granules or placebo once daily. Patients and investigators were blinded to treatment allocation. The primary endpoints were the salivary flow rate, Schirmer test results, and sugar test results. Intention-to-treat and per-protocol analyses were performed. All 240 patients were randomly allocated to either the treatment group (n = 160, ShengJinRunZaoYangXue granules) or placebo group (n = 80) and were included in the intention-to-treat analysis. After program violation and loss to follow-up, a total of 199 patients were included in the per-protocol analysis. At six week, intention-to-treat and per-protocol analyses of the left-eye Schirmer I test results showed an improved difference of 1.36 mm/5 min (95% CI: 0.03 to 2.69 mm/5 min) and 1.35 mm/5 min (95% CI: 0.04 to 2.73 mm/5 min), respectively, and those of the right-eye Schirmer I test results showed an improved difference of 1.12 mm/5 min (95% CI: 0.02 to 2.22 mm/5 min) and 1.12 mm/5 min (95% CI: -0.02 to 2.27 mm/5 min), respectively. There was no significant difference between the two groups before treatment. After treatment, the between-group and within-group before-and-after paired comparison results were statistically significant (P < 0.05). Intention-to-treat and per-protocol analyses showed an improved salivary flow rate by 0.04 ml/15 min (95

Comparative pharmacokinetics of swertiamarin in rats after oral administration of swertiamarin alone, Qing Ye Dan tablets and co-administration of swertiamarin and oleanolic acid.

PubMed

Xu, Gui-li; Li, Hong-liang; He, Jian-chang; Feng, En-fu; Shi, Pan-pan; Liu, Yue-qiong; Liu, Chang-xiao

2013-08-26

Qing Ye Dan is a well-known herbal drug that is widely used to treat viral hepatitis in the Yi and Hani minority regions in the Yunnan province of China. An LC-MS/MS method was developed to determine the levels of swertiamarin in rat plasma. Swertiamarin and naringin (internal standard, IS) were extracted from rat plasma using solid-phase extraction (SPE) to purify the samples. The pharmacokinetics of the following different administration methods of swertiamarin in rats were studied: oral administration of swertiamarin alone, a Qing Ye Dan tablet (QYDT) and co-administration of swertiamarin and oleanolic acid, with each method delivering approximately 20mg/kg of swertiamarin. Non-compartmental pharmacokinetic profiles were constructed by using the software DAS (version 2.1.1), and the pharmacokinetic parameters were compared using an unpaired Student's t-test. The results showed that the pharmacokinetic parameters Cmax, AUC0-∞, Vz/F and CLz/F were significantly different (P<0.05) among the three types of swertiamarin administration. The data indicate that oleanolic acid and the other ingredients present in QYDT could affect the pharmacokinetic behaviour of swertiamarin in rats. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

New molten salt systems for high temperature molten salt batteries: Ternary and quaternary molten salt systems based on LiF-LiCl, LiF-LiBr, and LiCl-LiBr

NASA Astrophysics Data System (ADS)

Fujiwara, Syozo; Inaba, Minoru; Tasaka, Akimasa

Using a new simulative technique developed by us, we systematically investigated new ternary or quaternary molten salt systems, which are based on LiF-LiCl, LiF-LiBr, and LiCl-LiBr binary systems, for use as electrolytes in thermal batteries, and evaluated their ionic conductivities and melting points experimentally. It was confirmed experimentally that LiF-LiBr-KF (melting point: 425 °C, ionic conductivity at 500 °C: 2.52 S cm -1), LiCl-LiBr-KF (405 °C, 2.56 S cm -1), LiCl-LiBr-NaF-KF (425 °C, 3.11 S cm -1), LiCl-LiBr-NaCl-KCl (420 °C, 2.73 S cm -1), and LiCl-LiBr-NaBr-KBr (420 °C, 2.76 S cm -1) meet our targets for both melting point (350-430 °C) and ionic conductivity (2.0 S cm -1 and higher at 500 °C). A single cell using the newly developed LiCl-LiBr-NaCl-KCl molten salt as an electrolyte was prepared, and the DC-IR of the cell decreased by 20% than that of a single cell using the conventional LiCl-KCl molten salt. It was therefore concluded that the use of new quaternary molten salt systems can improve the discharge rate-capability in practical battery applications because of their high ionic conductivities.

Theoretical Study of Hydrogen Adsorption on the GaN(0001) Surface

DTIC Science & Technology

2004-06-01

423 (1999) 70. [39] J.E. Northrup, J. Neugebauer, R.M. Feenstra, A.R. Smith, Phys. Rev. B 61 (2000) 9932. [40] K. Nakamura, T. Hayashi , A. Tachibana, K...Hasegawa, I.S.T. Tsong, T. Sakurai, T. Ohno , Phys. Rev. Lett. 82 (1999) 3074. [45] K. Raghavachari, Q. Fu, G. Chen, L. Li, C.H. Li, D.C. Law, R.F. Hicks, J...Xue, S. Kuwano, J.T. Sadowski, K.F. Kelly, T. Sakurai, T. Ohno , Phys. Rev. Lett. 84 (2000) 4015. [78] S. Vézian, F. Semond, J. Massies, D.W. Bullock, Z

Lithium salts for advanced lithium batteries: Li-metal, Li-O 2, and Li-S

DOE PAGES

Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik; ...

2015-06-01

Presently lithium hexafluorophosphate (LiPF 6) is the dominant Li-salt used in commercial rechargeable lithium-ion batteries (LIBs) based on a graphite anode and a 3-4 V cathode material. While LiPF 6 is not the ideal Li-salt for every important electrolyte property, it has a uniquely suitable combination of properties (temperature range, passivation, conductivity, etc.) rendering it the overall best Li-salt for LIBs. However, this may not necessarily be true for other types of Li-based batteries. Indeed, next generation batteries, for example lithium-metal (Li-metal), lithium-oxygen (Li-O 2), and lithium sulphur (Li-S), require a re-evaluation of Li-salts due to the different electrochemical andmore » chemical reactions and conditions within such cells. Furthermore, this review explores the critical role Li-salts play in ensuring in these batteries viability.« less

Clinical trials for treating recurrent head and neck cancer with boron neutron capture therapy using the Tsing-Hua Open Pool Reactor.

PubMed

Wang, Ling-Wei; Liu, Yen-Wan Hsueh; Chou, Fong-In; Jiang, Shiang-Huei

2018-06-19

Head and neck (HN) cancer is an endemic disease in Taiwan, China. Locally recurrent HN cancer after full-dose irradiation poses a therapeutic challenge, and boron neutron capture therapy (BNCT) may be a solution that could provide durable local control with tolerable toxicity. The Tsing-Hua Open Pool Reactor (THOR) at National Tsing-Hua University in Hsin-Chu, provides a high-quality epithermal neutron source for basic and clinical BNCT research. Our first clinical trial, entitled "A phase I/II trial of boron neutron capture therapy for recurrent head and neck cancer at THOR", was carried out between 2010 and 2013. A total of 17 patients with 23 recurrent HN tumors who had received high-dose photon irradiation were enrolled in the study. The fructose complex of L-boronophenylalanine was used as a boron carrier, and a two-fraction BNCT treatment regimen at 28-day intervals was used for each patient. Toxicity was acceptable, and although the response rate was high (12/17), re-recurrence within or near the radiation site was common. To obtain better local control, another clinical trial entitled "A phase I/II trial of boron neutron capture therapy combined with image-guided intensity-modulated radiotherapy (IG-IMRT) for locally recurrent HN cancer" was initiated in 2014. The first administration of BNCT was performed according to our previous protocol, and IG-IMRT was initiated 28 days after BNCT. As of May 2017, seven patients have been treated with this combination. The treatment-related toxicity was similar to that previously observed with two BNCT applications. Three patients had a complete response, but locoregional recurrence was the major cause of failure despite initially good responses. Future clinical trials combining BNCT with other local or systemic treatments will be carried out for recurrent HN cancer patients at THOR.

[Application and case analysis on the problem-based teaching of Jingluo Shuxue Xue (Science of Meridian and Acupoint) in reference to the team oriented learning method].

PubMed

Ma, Ruijie; Lin, Xianming

2015-12-01

The problem based teaching (PBT) has been the main approach to the training in the universities o the world. Combined with the team oriented learning method, PBT will become the method available to the education in medical universities. In the paper, based on the common questions in teaching Jingluo Shuxue Xue (Science of Meridian and Acupoint), the concepts and characters of PBT and the team oriented learning method were analyzed. The implementation steps of PBT were set up in reference to the team oriented learning method. By quoting the original text in Beiji Qianjin Yaofang (Essential recipes for emergent use worth a thousand gold), the case analysis on "the thirteen devil points" was established with PBT.

Sensilla on the Antennae and Ovipositor of the Sea Buckthorn Carpenter Moth, Holcocerus hippophaecolus Hua et al (Lepidoptera: Cossidae).

PubMed

Wang, R; Zhang, L; Xu, L L; Zong, S X; Luo, Y Q

2015-02-01

Holcocerus hippophaecolus Hua et al (Lepidoptera: Cossidae) is an important boring pest that damages the sea buckthorn Hippophae rhamnoides. Larvae of H. hippophaecolus cause major losses of this shrub in Northern China, with severe economic and ecological consequences. In this study, we used scanning electron microscopy to investigate the typology, morphology, and distribution of sensilla on the antennae and ovipositor of H. hippophaecolus. In total, seven subtypes of sensilla were found on the antennae, i.e., chaetica, trichodea (two subtypes), basiconica (two subtypes), coeloconica, and Böhm bristles. In addition, three types of sensilla were detected on the ovipositor, i.e., chaetica, trichodea, and basiconica. The identification of these sensilla types could provide morphological evidence to facilitate a better understanding of the host location, mate finding, and oviposition processes of this important species.

A rapid UFLC-MS/MS method for simultaneous determination of formononetin, cryptotanshinone, tanshinone IIA and emodin in rat plasma and its application to a pharmacokinetic study of Bu Shen Huo Xue formula.

PubMed

Xu, Yuping; Huang, Kexin; Pan, Yu; Wang, Xianqin; Yan, Pengcheng; Ren, Yiping; Xiang, Zheng

2013-08-01

Bu Shen Huo Xue formula (BSHX) is a traditional Chinese medicine prescription used for clinical treatment of chronic kidney diseases. A rapid and selective Ultra fast liquid chromatography with tandem mass spectrometry (UFLC-MS/MS) method was developed for simultaneous determination of four bioactive components of BSHX including formononetin, cryptotanshinone, tanshinone IIA, and emodin in control and unilateral ureteral obstruction (UUO) model rat plasma for the first time. Atorvastatin was used as the internal standard (IS). Plasma samples were extracted by liquid-liquid extraction with ethyl acetate. The chromatographic separation was carried out on a Shim-pack XR-ODS III column with a gradient mobile phase consisting of acetonitrile and 0.1% formic acid. The detection was performed on a triple-quad tandem mass spectrometer by multiple reaction monitoring (MRM) via electrospray ionization (ESI) source with positive ionization mode for formononetin, cryptotanshinone, tanshinone IIA, and negative mode for emodin. The method was linear for four analytes over the range of investigated concentration with all coefficients of determination (R(2)) greater than 0.9938. The lower limits of quantification (LLOQ) for formononetin, cryptotanshinone, tanshinone IIA, and emodin were defined as 0.3, 0.5, 1.5, and 0.3ng/mL, respectively. The rapid and sensitive method was fully validated and successfully applied to the pharmacokinetic study of formononetin, cryptotanshinone, tanshinone IIA and emodin in rats following oral administration of Bu Shen Huo Xue formula. Copyright © 2013 Elsevier B.V. All rights reserved.

Between the Living and the Dead: Trauma Medicine and Forensic Medicine in the Mid-Qing

PubMed Central

Wu, Yi-Li

2015-01-01

This paper analyzes the influence of forensic medicine on therapeutic medicine through a case study of Qian Xiuchang and Hu Tingguang, two Chinese doctors who specialized in treating traumatic injuries. During the early nineteenth century, both men compiled medical treatises that sought to improve on a scholarly model of “rectifying bones” articulated in 1742 by the Imperially-Compiled Golden Mirror of the Medical Lineage. Both texts also incorporated information from forensic medicine, including official inquest diagrams and checklists promulgated by the Qing government. I show that they drew on these forensic materials to help address two interlinked medical issues: understanding the effects of injury on different parts of the body, and clarifying the location and form of the body’s bones. Overall, I suggest that the exchange of ideas between the realm of therapeutic medicine and forensic medicine was an important epistemological strategy that doctors and officials alike employed to improve their knowledge of the material body. PMID:26512255

Between the Living and the Dead: Trauma Medicine and Forensic Medicine in the Mid-Qing.

PubMed

Wu, Yi-Li

2015-03-01

This paper analyzes the influence of forensic medicine on therapeutic medicine through a case study of Qian Xiuchang and Hu Tingguang, two Chinese doctors who specialized in treating traumatic injuries. During the early nineteenth century, both men compiled medical treatises that sought to improve on a scholarly model of "rectifying bones" articulated in 1742 by the Imperially-Compiled Golden Mirror of the Medical Lineage . Both texts also incorporated information from forensic medicine, including official inquest diagrams and checklists promulgated by the Qing government. I show that they drew on these forensic materials to help address two interlinked medical issues: understanding the effects of injury on different parts of the body, and clarifying the location and form of the body's bones. Overall, I suggest that the exchange of ideas between the realm of therapeutic medicine and forensic medicine was an important epistemological strategy that doctors and officials alike employed to improve their knowledge of the material body.

Cytotaxonomy and molecular phylogeny of the genus Cerapanorpa Gao, Ma & Hua, 2016 (Mecoptera: Panorpidae).

PubMed

Miao, Ying; Ma, Na; Hua, Bao-Zhen

2017-07-03

The species of the genus Cerapanorpa Gao, Ma & Hua, 2016 (Mecoptera: Panorpidae) are characterized mainly by the presence of a finger-like anal horn on tergum VI of males and are distributed in the Oriental and eastern Palearctic regions. Herein, we investigated the pachytene banding patterns and reconstructed the Bayesian time-calibrated tree of some species of Cerapanorpa. All species examined display achiasmate meiosis and the same meiformula 2n = 42 + X0, reconfirming the monophyly of Cerapanorpa. The great variations in the size and number of heterochromatic bands suggest that they are reliable traits for species delimitation in Cerapanorpa. The existence of natural C-banding polymorphism indicates that chromosomal rearrangements likely have contributed to the diversification of chromosomal bands in Cerapanorpa. The closely related species of Cerapanorpa are reconfirmed to be evolutionarily independent entities by cytogenetic and molecular data. The divergence time estimated from the BEAST analysis shows that Cerapanorpa likely originated in the period from the Rupelian (30.7 Ma) to the Burdigalian (19.9 Ma), and most diversification occurred from the Burdigalian to the Piacenzian (17.4-2.8 Ma) in the Neogene. Our data suggest that chromosome rearrangements likely play a significant role in the speciation of Cerapanorpa.

Hydrogen retention in Li and Li-C-O films

NASA Astrophysics Data System (ADS)

Buzi, Luxherta; Nelson, Andrew O.; Yang, Yuxin; Kaita, Robert; Koel, Bruce E.

2017-10-01

The efficiency of Li in binding H isotopes has led to reduced recycling in magnetic fusion devices and improved plasma performance. Since elemental Li surfaces are challenging to maintain in fusion devices due to the presence of impurities, parameterizing and understanding the mechanisms for H retention in various Li compounds (Li-C-O), in addition to pure Li, is crucial for Li plasma-facing material applications. To determine H retention in Li and Li-C-O films, measurements were done under ultrahigh vacuum conditions using temperature programmed desorption (TPD). Thin Li films (20 monolayers) were deposited on a nickel single crystal substrate and irradiated with 500 eV H2+ions at surface temperatures from 90K to 520K. Initial measurements on Li and Li-O films showed that the retention was comparable and dropped exponentially with surface temperature, from 95% at 90 K to 35% at 520 K. Auger electron spectroscopy and TPD showed that H was retained as lithium hydride (LiH) in pure Li and as lithium hydroxide (LiOH) in Li2O, which decomposed to H2O and Li2O at temperatures higher than 470K. H retention in Li-C and Li-C-O films will be determined over a similar temperature range, and the sputtering rate of these layers with H ions will also be reported. This material is based upon work supported by the U.S. Department of Energy, Office of Science/Fusion Energy Sciences under Award Number DE-SC0012890.

First Public Report on the Military Academy Chinese People’s Liberation Army Military Pictures Collection (Selected Articles),

DTIC Science & Technology

1986-10-10

Cooperation, by Liu Jienyang, Zhao Rueishan, Ze Fu .......... 35 > A Visit to the Institute of Guided Missile Technology, by Zhang Juzheng, Li Weiliang...4,. *1 .4 9- -I. .p *. .4 I-.- a. S.... .4 11 l.a. 9-.4 *49.4*~*9*~. ° - S’: Key: (1) Analyst Li Xien studies techniques hard in the field in...leader Chairman Hua, Vice Chairmen Ye Jianying , Deng Xiao- ping, Wang Dongxing and other leaders of the party, state and militaryarrived at the

JPRS Report, Arms Control

DTIC Science & Technology

1989-11-13

manufacturing or using beam facilities. Radiation signs and necessary protection security interlocking mechanisms, alarm systems, or signals must be...JPRS-TAC-89-037 13 NOVEMBER 1989 JPRS tit Arms Control 715 159 REPRODUCED BY US DEPARTMENT OF COMMERCE NATIONAL TECHNICAL INFORMATION SERVICE...Xue Ren; J1EFANGJUN BAO 20 Oct] 4 Li Peng Signs Radiation Protection Decree [XINHUA 1 Nov] 5 Nuclear Technology Applied to Nonmilitary Use

Molecular Relaxation in LiNO3-LiClO4 and Li2CO3-Li2SO4 Solid Binary Systems

NASA Astrophysics Data System (ADS)

Aliev, A. R.; Akhmedov, I. R.; Kakagasanov, M. G.; Aliev, Z. A.; Gafurov, M. M.; Amirov, A. M.

2018-06-01

The paper presents spectroscopic combinational scattering investigations of the molecular relaxation in LiNO3-LiClO4 and Li2CO3-Li2SO4 solid binary systems. It is found that the relaxation time for ν1(A) vibrations of NO3 - anion in LiNO3-LiClO4 system is lower than in LiNO3 crystal. And the relaxation time for ν1(A) vibrations of CO3 2- anion in Li2CO3-Li2SO4 system is lower than in Li2CO3 crystal. The increase in the relaxation time is explained by the additional relaxation mechanism of the excited mode of nitrate and carbon ions which is observed in these systems. This mechanism is linked to the vibrations of other anions (ClO4 - or SO4 2-) and a nucleation of the lattice phonon. Experiments show that the additional relaxation mechanism occurs due to the vibration difference which corresponds to the area of rather a high density of states of the phonon spectrum.

Ab initio and kinetic Monte Carlo study of lithium diffusion in LiSi, Li12Si7, Li13Si5 and Li15Si4

NASA Astrophysics Data System (ADS)

Moon, Janghyuk; Lee, Byeongchan; Cho, Maenghyo; Cho, Kyeongjae

2016-10-01

The kinetics of lithium atoms in various Li-Si binary compounds are investigated using density functional theory calculations and kinetic Monte Carlo calculations. The values of the Li migration energy barriers are identified by NEB calculations with vacancy-mediated, interstitial and exchange migration mechanisms in crystalline LiSi, Li12Si7, Li13Si4, and Li15Si4. A comparison of these NEB results shows that the vacancy-mediated Li migration is identified as the dominant diffusion mechanisms in Li-Si compounds. The diffusion coefficients of Li in Li-Si compounds at room temperature are determined by KMC simulation. From the KMC results, the recalculated migration energy barriers in LiSi, Li12Si7, Li13Si4, and Li15Si4 correspond to 0.306, 0.301, 0.367 and 0.320 eV, respectively. Compared to the Li migration energy barrier of 0.6 eV in crystalline Si, the drastic reduction in the Li migration energy barriers in the lithiated silicon indicates that the initial lithiation of the Si anode is the rate-limiting step. Furthermore, it is also found that Si migration is possible in Li-rich configurations. On the basis of these findings, the underlying mechanisms of kinetics on the atomic scale details are elucidated.

RETRACTED: Association of the ACE I/D gene polymorphism with sepsis susceptibility and sepsis progression.

PubMed

Yang, Chun-Hua; Zhou, Tian-Biao

2015-12-01

This article has been included in a multiple retraction: Chun-Hua Yang and Tian-Biao Zhou Association of the ACE I/D gene polymorphism with sepsis susceptibility and sepsis progression Journal of Renin-Angiotensin-Aldosterone System 1470320314568521, first published on February 3, 2015 doi: 10.1177/1470320314568521 This article has been retracted at the request of the Editors and the Publisher. After conducting a thorough investigation, SAGE found that the submitting authors of a number of papers published in the Journal of the Renin-Angiotensin Aldosterone System ( JRAAS) (listed below) had supplied fabricated contact details for their nominated reviewers. The Editors accepted these papers based on the reports supplied by the individuals using these fake reviewer email accounts. After concluding that the peer review process was therefore seriously compromised, SAGE and the journal Editors have decided to retract all affected articles. Online First articles (these articles will not be published in an issue) Wenzhuang Tang, Tian-Biao Zhou, and Zongpei Jiang Association of the angiotensinogen M235T gene polymorphism with risk of diabetes mellitus developing into diabetic nephropathy Journal of Renin-Angiotensin-Aldosterone System 1470320314563426, first published on December 18, 2014 doi: 10.1177/1470320314563426 Tian-Biao Zhou, Hong-Yan Li, Zong-Pei Jiang, Jia-Fan Zhou, Miao-Fang Huang, and Zhi-Yang Zhou Role of renin-angiotensin-aldosterone system inhibitors in radiation nephropathy Journal of Renin-Angiotensin-Aldosterone System 1470320314563424, first published on December 18, 2014 doi: 10.1177/1470320314563424 Weiqiang Zhong, Zongpei Jiang, and Tian-Biao Zhou Association between the ACE I/D gene polymorphism and T2DN susceptibility: The risk of T2DM developing into T2DN in the Asian population Journal of Renin-Angiotensin-Aldosterone System 1470320314566019, first published on January 26, 2015 doi: 10.1177/1470320314566019 Tian-Biao Zhou, Xue-Feng Guo, Zongpei

Kinetic measurement and prediction of the hydrogen outgassing from the polycrystalline LiH/Li 2O/LiOH system

NASA Astrophysics Data System (ADS)

Dinh, L. N.; Grant, D. M.; Schildbach, M. A.; Smith, R. A.; Siekhaus, W. J.; Balazs, B.; Leckey, J. H.; Kirkpatrick, J. R.; McLean, W.

2005-12-01

Due to the exothermic reaction of lithium hydride (LiH) salt with water during transportation and handling, there is always a thin film of lithium hydroxide (LiOH) present on the LiH surface. In dry or vacuum storage, this thin LiOH film slowly decomposes. The technique of temperature-programmed reaction/decomposition (TPR) was employed in combination with the isoconversion method of thermal analysis to determine the outgassing kinetics of H 2O from pure LiOH and H 2 and H 2O from this thin LiOH film. H 2 production via the reaction of LiH with LiOH, forming a lithium oxide (Li 2O) interlayer, is thermodynamically favored, with the rate of further reaction limited by diffusion through the Li 2O and the stability of the decomposing LiOH. Lithium hydroxide at the LiOH/vacuum interface also decomposes easily to Li 2O, releasing H 2O which subsequently reacts with LiH in a closed system to form H 2. At the onset of dry decomposition, where H 2 is the predominant product, the activation energy for outgassing from a thin LiOH film is lower than that for bulk LiOH. However, as the reactions at the LiH/Li 2O/LiOH and at the LiOH/vacuum interfaces proceed, the overall activation energy barrier for the outgassing approaches that of bulk LiOH decomposition. The kinetics developed here predict a hydrogen evolution profile in good agreement with hydrogen release observed during long term isothermal storage.

China’s Nuclear Force Modernization

DTIC Science & Technology

2005-01-01

of mass destruction, see 美伊 战 争 引发核竞 赛？[U.S. War on Iraq Initiated Nuclear Races?], 世界新闻报 [World News Journal], 1 May 2003. 41. Lewis and Hua...Plana, Spain, May 2003. ———.美伊 战 争 引发核竞赛？[U.S. War on Iraq Initiated Nuclear Races?], 世界新闻报 [World News Journal], no. 33, 1 May 2003. Lewis, John, Hua...彬 [Zhou Baogen and Li Bin], 党派政治对冷 战 后美国军控政策的 影响 [Impacts of Party Politics on Ameri- can Arms Control Policy after the Cold War], 世界经济与政治论坛 [Forum

New molten salt systems for high-temperature molten salt batteries: LiF-LiCl-LiBr-based quaternary systems

NASA Astrophysics Data System (ADS)

Fujiwara, Syozo; Inaba, Minoru; Tasaka, Akimasa

To develop novel multi-component molten salt systems more effectively, we developed a simulative technique using the CALPHAD (Calculation of Phase Diagram and Thermodynamics) method to estimate the ionic conductivity and the melting point. The validity of this new simulative technique was confirmed by comparing the simulated ionic conductivities and melting points of typical high-temperature molten salts, such as LiF-LiCl-LiBr, LiF-LiBr-KBr, LiCl-LiBr-KBr, and LiCl-LiBr-LiI, with those reported data in the literature or experimentally obtained. This simulative technique was used to develop new quaternary molten salt systems for use as electrolytes in high-temperature molten salt batteries (called thermal batteries). The targets of the ionic conductivity and the melting point were set at 2.0 S cm -1 and higher at 500 °C, and in the range of 350-430 °C, respectively, to replace the LiCl-KCl system (1.85 S cm -1 at 500 °C) within the conventional design of the heat generation system for thermal batteries. Using the simulative method, six kinds of novel quaternary systems, LiF-LiCl-LiBr-MX (M = Na and K; X = F, Cl, and Br), which contain neither environmentally instable anions such as iodides nor expensive cations such as Rb + and Cs +, were proposed. Experimental results showed that the LiF-LiCl-LiBr-0.10NaX (X = Cl and Br) and LiF-LiCl-LiBr-0.10KX (X = F, Cl, and Br) systems meet our targets of both the ionic conductivity and the melting point.

Unravelling Li-Ion Transport from Picoseconds to Seconds: Bulk versus Interfaces in an Argyrodite Li6PS5Cl-Li2S All-Solid-State Li-Ion Battery.

PubMed

Yu, Chuang; Ganapathy, Swapna; de Klerk, Niek J J; Roslon, Irek; van Eck, Ernst R H; Kentgens, Arno P M; Wagemaker, Marnix

2016-09-07

One of the main challenges of all-solid-state Li-ion batteries is the restricted power density due to the poor Li-ion transport between the electrodes via the electrolyte. However, to establish what diffusional process is the bottleneck for Li-ion transport requires the ability to distinguish the various processes. The present work investigates the Li-ion diffusion in argyrodite Li6PS5Cl, a promising electrolyte based on its high Li-ion conductivity, using a combination of (7)Li NMR experiments and DFT based molecular dynamics simulations. This allows us to distinguish the local Li-ion mobility from the long-range Li-ion motional process, quantifying both and giving a coherent and consistent picture of the bulk diffusion in Li6PS5Cl. NMR exchange experiments are used to unambiguously characterize Li-ion transport over the solid electrolyte-electrode interface for the electrolyte-electrode combination Li6PS5Cl-Li2S, giving unprecedented and direct quantitative insight into the impact of the interface on Li-ion charge transport in all-solid-state batteries. The limited Li-ion transport over the Li6PS5Cl-Li2S interface, orders of magnitude smaller compared with that in the bulk Li6PS5Cl, appears to be the bottleneck for the performance of the Li6PS5Cl-Li2S battery, quantifying one of the major challenges toward improved performance of all-solid-state batteries.

Binding energy of donor impurity states and optical absorption in the Tietz-Hua quantum well under an applied electric field

NASA Astrophysics Data System (ADS)

Al, E. B.; Kasapoglu, E.; Sakiroglu, S.; Duque, C. A.; Sökmen, I.

2018-04-01

For a quantum well which has the Tietz-Hua potential, the ground and some excited donor impurity binding energies and the total absorption coefficients, including linear and third order nonlinear terms for the transitions between the related impurity states with respect to the structure parameters and the impurity position as well as the electric field strength are investigated. The binding energies were obtained using the effective-mass approximation within a variational scheme and the optical transitions between any two impurity states were calculated by using the density matrix formalism and the perturbation expansion method. Our results show that the effects of the electric field and the structure parameters on the optical transitions are more pronounced. So we can adjust the red or blue shift in the peak position of the absorption coefficient by changing the strength of the electric field as well as the structure parameters.

Madame Li Li: Communist Revolutionary, Adult Educator, Lifelong Learner

ERIC Educational Resources Information Center

Boshier, Roger; Huang, Yan

2009-01-01

Prior to 1949 the Chinese Communist Party orchestrated innovative and participatory forms of adult education. This article concerns Madame Li Li, a leading Chinese Communist woman adult educator. Western delegates at the International Council for Adult Education 1984 Shanghai symposium on adult education were fascinated by Madame Li Li because,…

On the Corrosion Performance of Monel 400 in Molten LiCl-Li2O-Li at 923 K

NASA Astrophysics Data System (ADS)

Phillips, William; Merwin, Augustus; Chidambaram, Dev

2018-06-01

The corrosion resistance of a Ni-Cu alloy, Monel 400, in molten LiCl-Li2O-Li at 923 K (650 °C) was investigated. Exposure testing of Monel 400 samples submerged in molten LiCl-2 wt pct Li2O solutions with Li concentrations between zero and 1 wt pct was performed at 923 K (650°C) for 20 hours. Post exposure surface analysis was performed using X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, optical microscopy, micro-Vickers hardness testing, and X-ray photoelectron spectroscopy, while inductively coupled plasma optical emission spectroscopy was used to quantify the rate of material leaching. The extent of material degradation was observed to be strongly correlated to the concentration of metallic Li in the molten LiCl-Li2O system.

Li + Defects in a Solid-State Li Ion Battery: Theoretical Insights with a Li 3 OCl Electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stegmaier, Saskia; Voss, Johannes; Reuter, Karsten

In a solid-state Li ion battery, the solid-state electrolyte exits principally in regions of high externally applied potentials, and this varies rapidly at the interfaces with electrodes due to the formation of electrochemical double layers. Here, we investigate the implications of these for a model solid-state Li ion battery Li|Li 3OCl|C, where C is simply a metallic intercalation cathode. We use DFT to calculate the potential dependence of the formation energies of the Li + charge carriers in superionic Li 3OCl. We find that Li+ vacancies are the dominant species at the cathode while Li+ interstitials dominate at the anode.more » With typical Mg aliovalent doping of Li 3OCl, Li + vacancies dominate the bulk of the electrolyte as well, with freely mobile vacancies only ~ 10 -4 of the Mg doping density at room temperature. We study the repulsive interaction between Li+ vacancies and find that this is extremely short range, typically only one lattice constant due to local structural relaxation around the vacancy and this is significantly shorter than pure electrostatic screening. We model a Li 3OCl- cathode interface by treating the cathode as a nearly ideal metal using a polarizable continuum model with an ε r = 1000. There is a large interface segregation free energy of ~ - 1 eV per Li + vacancy. Combined with the short range for repulsive interactions of the vacancies, this means that very large vacancy concentrations will build up in a single layer of Li 3OCl at the cathode interface to form a compact double layer. The calculated potential drop across the interface is ~ 3 V for a nearly full concentration of vacancies at the surface. This suggests that nearly all the cathode potential drop in Li 3OCl occurs at the Helmholtz plane rather than in a diffuse space-charge region. We suggest that the conclusions found here will be general to other superionic conductors as well.« less

Li + Defects in a Solid-State Li Ion Battery: Theoretical Insights with a Li 3 OCl Electrolyte

DOE PAGES

Stegmaier, Saskia; Voss, Johannes; Reuter, Karsten; ...

2017-04-26

In a solid-state Li ion battery, the solid-state electrolyte exits principally in regions of high externally applied potentials, and this varies rapidly at the interfaces with electrodes due to the formation of electrochemical double layers. Here, we investigate the implications of these for a model solid-state Li ion battery Li|Li 3OCl|C, where C is simply a metallic intercalation cathode. We use DFT to calculate the potential dependence of the formation energies of the Li + charge carriers in superionic Li 3OCl. We find that Li+ vacancies are the dominant species at the cathode while Li+ interstitials dominate at the anode.more » With typical Mg aliovalent doping of Li 3OCl, Li + vacancies dominate the bulk of the electrolyte as well, with freely mobile vacancies only ~ 10 -4 of the Mg doping density at room temperature. We study the repulsive interaction between Li+ vacancies and find that this is extremely short range, typically only one lattice constant due to local structural relaxation around the vacancy and this is significantly shorter than pure electrostatic screening. We model a Li 3OCl- cathode interface by treating the cathode as a nearly ideal metal using a polarizable continuum model with an ε r = 1000. There is a large interface segregation free energy of ~ - 1 eV per Li + vacancy. Combined with the short range for repulsive interactions of the vacancies, this means that very large vacancy concentrations will build up in a single layer of Li 3OCl at the cathode interface to form a compact double layer. The calculated potential drop across the interface is ~ 3 V for a nearly full concentration of vacancies at the surface. This suggests that nearly all the cathode potential drop in Li 3OCl occurs at the Helmholtz plane rather than in a diffuse space-charge region. We suggest that the conclusions found here will be general to other superionic conductors as well.« less

BATTLE (Biomarker-based Approach of Targeted Therapy for Lung Cancer Elimination)

DTIC Science & Technology

2012-04-01

Wistuba,Ignacio Ivan Woods ,Denise M Wu,Huakang Xue,Yuwen Yang,Bijun Yin,Ming Zhang,Guangcheng Zhang,Li Army...Oncol. 2009; 27: 271–8. 127 Ishii Y, Rex M, Scotting PJ et al. Region-specific expression of chicken Sox2 in the developing gut and lung epithelium... Wood ER, Shewchuk L, Hassel A, et al. Discovery of an in- hibitor of insulin-like growth factor 1 receptor activation: implications for cellular potency

Minimum Error Bounded Efficient L1 Tracker with Occlusion Detection (PREPRINT)

DTIC Science & Technology

2011-01-01

Minimum Error Bounded Efficient `1 Tracker with Occlusion Detection Xue Mei\\ ∗ Haibin Ling† Yi Wu†[ Erik Blasch‡ Li Bai] \\Assembly Test Technology...proposed BPR-L1 tracker is tested on several challenging benchmark sequences involving chal- lenges such as occlusion and illumination changes. In all...point method de - pends on the value of the regularization parameter λ. In the experiments, we found that the total number of PCG is a few hundred. The

The Dangers of ‘Warming and Replenishing’ (wenbu 溫補) during the Ming to Qing Epistemic Transition

PubMed Central

de Vries, Leslie

2016-01-01

Through a case study of Zhao Xianke’s 趙獻可 One Principle through Medicine (Yiguan 醫貫) (1617?) and Xu Dachun’s 徐大椿 (1693–1771) denouncements of this text, my article zooms in on divergent discourses on the safety and efficacy of medicinal substances and compounds in late imperial China. Although Xu Dachun’s fierce attacks on the popular ‘warming and replenishing’ (wenbu 溫補) therapies can be situated in an epistemic shift from the cosmology of ‘Song learning’ (songxue 宋學) towards the philology of ‘Han learning’ (hanxue 漢學) and ‘evidential research’ (kaozheng 考證), I argue that more complex issues were at stake as well. Changed political, social, ethical, and economic realities shaped new and multifaceted perceptions of the nature of medicine, the medical profession, and the usage of medicinals in the aftermath of the Ming to Qing transition. PMID:27818620

The organic materials in the Five Northern Provinces' Assembly Hall: disclosing the painting technique of the Qing dynasty painters in civil buildings

NASA Astrophysics Data System (ADS)

Lluveras-Tenorio, A.; Bonaduce, I.; Sabatini, F.; Degano, I.; Blaensdorf, C.; Pouyet, E.; Cotte, M.; Ma, L.; Colombini, M. P.

2015-11-01

The beiwusheng huiguan (`Meeting hall of the Five Northern Dynasties') is a building complex from the Qing dynasty (1636-1912 ad) located in Wafangdian, near Ziyang, in the south of the Chinese Province of Shaanxi. Two of the preserved halls are richly decorated with wall paintings dated probably in 1848 ad and representing scenes of the `Romance of the Three Kingdoms' and Confucian moral tales. They are a rare example of well-preserved mural paintings of high artistic value inside civil buildings. The aims of this paper are the chemical characterization and localization of organic materials used as binders and colorants in the wall paintings. A multi-analytical approach, consisting in the combined use of gas chromatographic-mass spectrometric techniques (GC/MS and Py-GC/MS) and high-pressure liquid chromatography with diode array detector (HPLC-DAD), was chosen for these purposes. Proteinaceous materials (animal glue and egg), saccharide material (fruit tree gum) and a siccative oil were identified in different paint layers supplying invaluable information about the painting technique used. Moreover, the analyses of organic dyes allowed identifying indigo and gallic acid in more than one sample adding fundamental information about Chinese artists' techniques in mural paintings, missing from the previous studies. To shed light on the gilding technique, the distribution of the painting materials was achieved by means of synchrotron radiation Fourier transform infrared spectroscopy (SR micro-FTIR) and X-ray fluorescence (SR micro-XRF). The results obtained from the multi-analytical approach enabled us to determine the organic materials both binders and organic colorants used by Chinese artisans, highlighting the high technical level achieved in nineteenth century. The binding media and the organic colorants identified, as well as their distribution, allowed the discussion on the painting technique used by the artists of the Qing dynasty giving information for the

Seasonal characteristics of oxalic acid and related SOA in the free troposphere of Mt. Hua, central China: implications for sources and formation mechanisms.

PubMed

Meng, Jingjing; Wang, Gehui; Li, Jianjun; Cheng, Chunlei; Ren, Yanqin; Huang, Yao; Cheng, Yuting; Cao, Junji; Zhang, Ting

2014-09-15

PM10 aerosols from the summit of Mt. Hua (2060 m a.s.l) in central China during the winter and summer of 2009 were analyzed for dicarboxylic acids, ketocarboxylic acids and α-dicarbonyls. Molecular composition of dicarboxylic acids (C2-C11) in the free tropospheric aerosols reveals that oxalic acid (C2, 399 ± 261 ng m(-3) in winter and 522 ± 261 ng m(-3) in summer) is the most abundant species in both seasons, followed by malonic (C3) and succinic (C4) acids, being consistent with that on ground levels. Most of the diacids are more abundant in summer than in winter, but adipic (C6) and phthalic (Ph) acids are twice lower in summer, suggesting more significant impact of anthropogenic pollution on the wintertime alpine atmosphere. Moreover, glyoxal (Gly) and methylglyoxal (mGly) are also lower in summer (12 ± 6.1 ng m(-3)) than in winter (22 ± 13 ng m(-3)). As both dicarbonyls are a major precursor of C2, their seasonal variation patterns, which are opposite to those of the diacids, indicate that the mountain troposphere is more oxidative in summer. C2 showed strong linear correlations with levoglucosan in winter and oxidation products of isoprene and monoterpene in summer. PCA analysis further suggested that the wintertime C2 and related SOA in the Mt. Hua troposphere mostly originate from photochemical oxidations of anthropogenic pollutants emitted from biofuel and coal combustion in lowland regions. On contrast, the summertime C2 and related SOA mostly originate from further oxidation of the mountainous isoprene and monoterpene oxidation products. The AIM model calculation results showed that oxalic acid concentration well correlated with particle acidity (R(2)=0.60) but not correlated with particle liquid water content, indicating that particle acidity favors the organic acid formation because aqueous-phase C2 production is the primary mechanism of C2 formation in ambient aerosols and is driven by acid-catalyzed oxidation. Copyright © 2014 Elsevier B.V. All

Kinetic Monte Carlo Study of Li Intercalation in LiFePO4.

PubMed

Xiao, Penghao; Henkelman, Graeme

2018-01-23

Even as a commercial cathode material, LiFePO 4 remains of tremendous research interest for understanding Li intercalation dynamics. The partially lithiated material spontaneously separates into Li-poor and Li-rich phases at equilibrium. Phase segregation is a surprising property of LiFePO 4 given its high measured rate capability. Previous theoretical studies, aiming to describe Li intercalation in LiFePO 4 , include both atomic-scale density functional theory (DFT) calculations of static Li distributions and entire-particle-scale phase field models, based upon empirical parameters, studying the dynamics of the phase separation. Little effort has been made to bridge the gap between these two scales. In this work, DFT calculations are used to fit a cluster expansion for the basis of kinetic Monte Carlo calculations, which enables long time scale simulations with accurate atomic interactions. This atomistic model shows how the phases evolve in Li x FePO 4 without parameters from experiments. Our simulations reveal that an ordered Li 0.5 FePO4 phase with alternating Li-rich and Li-poor planes along the ac direction forms between the LiFePO 4 and FePO 4 phases, which is consistent with recent X-ray diffraction experiments showing peaks associated with an intermediate-Li phase. The calculations also help to explain a recent puzzling experiment showing that LiFePO 4 particles with high aspect ratios that are narrower along the [100] direction, perpendicular to the [010] Li diffusion channels, actually have better rate capabilities. Our calculations show that lateral surfaces parallel to the Li diffusion channels, as well as other preexisting sites that bind Li weakly, are important for phase nucleation and rapid cycling performance.

Li Distribution Heterogeneity in Solid Electrolyte Li10GeP2S12 upon Electrochemical Cycling Probed by 7Li MRI.

PubMed

Chien, Po-Hsiu; Feng, Xuyong; Tang, Mingxue; Rosenberg, Jens T; O'Neill, Sean; Zheng, Jin; Grant, Samuel C; Hu, Yan-Yan

2018-04-19

All-solid-state rechargeable batteries embody the promise for high energy density, increased stability, and improved safety. However, their success is impeded by high resistance for mass and charge transfer at electrode-electrolyte interfaces. Li deficiency has been proposed as a major culprit for interfacial resistance, yet experimental evidence is elusive due to the challenges associated with noninvasively probing the Li distribution in solid electrolytes. In this Letter, three-dimensional 7 Li magnetic resonance imaging (MRI) is employed to examine Li distribution homogeneity in solid electrolyte Li 10 GeP 2 S 12 within symmetric Li/Li 10 GeP 2 S 12 /Li batteries. 7 Li MRI and the derived histograms reveal Li depletion from the electrode-electrolyte interfaces and increased heterogeneity of Li distribution upon electrochemical cycling. Significant Li loss at interfaces is mitigated via facile modification with a poly(ethylene oxide)/bis(trifluoromethane)sulfonimide Li salt thin film. This study demonstrates a powerful tool for noninvasively monitoring the Li distribution at the interfaces and in the bulk of all-solid-state batteries as well as a convenient strategy for improving interfacial stability.

Thermal stability of LiPF 6 salt and Li-ion battery electrolytes containing LiPF 6

NASA Astrophysics Data System (ADS)

Yang, Hui; Zhuang, Guorong V.; Ross, Philip N.

The thermal stability of the neat lithium hexafluorophosphate (LiPF 6) salt and of 1 molal (m) solutions of LiPF 6 in prototypical Li-ion battery solvents was studied with thermogravimetric analysis (TGA) and on-line Fourier transform infrared (FTIR). Pure LiPF 6 salt is thermally stable up to 107 °C in a dry inert atmosphere, and its decomposition path is a simple dissociation producing lithium fluoride (LiF) as solid and PF 5 as gaseous products. In the presence of water (300 ppm) in the carrier gas, its decomposition onset temperature is lowered as a result of direct thermal reaction between LiPF 6 and water vapor to form phosphorous oxyfluoride (POF 3) and hydrofluoric acid (HF). No new products were observed in 1 m solutions of LiPF 6 in ethylene carbonate (EC), dimethyl carbonate (DMC) and ethyl methyl carbonate (EMC) by on-line TGA-FTIR analysis. The storage of the same solutions in sealed containers at 85 °C for 300-420 h did not produce any significant quantity of new products as well. In particular, no alkylflurophosphates were found in the solutions after storage at elevated temperature. In the absence of either an impurity like alcohol or cathode active material that may (or may not) act as a catalyst, there is no evidence of thermally induced reaction between LiPF 6 and the prototypical Li-ion battery solvents EC, PC, DMC or EMC.

Li2S Film Formation on Lithium Anode Surface of Li-S batteries.

PubMed

Liu, Zhixiao; Bertolini, Samuel; Balbuena, Perla B; Mukherjee, Partha P

2016-02-01

The precipitation of lithium sulfide (Li2S) on the Li metal anode surface adversely impacts the performance of lithium-sulfur (Li-S) batteries. In this study, a first-principles approach including density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations is employed to theoretically elucidate the Li2S/Li metal surface interactions and the nucleation and growth of a Li2S film on the anode surface due to long-chain polysulfide decomposition during battery operation. DFT analyses of the energetic properties and electronic structures demonstrate that a single molecule adsorption on Li surface releases energy forming chemical bonds between the S atoms and Li atoms from the anode surface. Reaction pathways of the Li2S film formation on Li metal surfaces are investigated based on DFT calculations. It is found that a distorted Li2S (111) plane forms on a Li(110) surface and a perfect Li2S (111) plane forms on a Li(111) surface. The total energy of the system decreases along the reaction pathway; hence Li2S film formation on the Li anode surface is thermodynamically favorable. The calculated difference charge density of the Li2S film/Li surface suggests that the precipitated film would interact with the Li anode via strong chemical bonds. AIMD simulations reveal the role of the anode surface structure and the origin of the Li2S formation via decomposition of Li2S8 polysulfide species formed at the cathode side and dissolved in the electrolyte medium in which they travel to the anode side during battery cycling.

Recovery of Li from alloys of Al- Li and Li- Al using engineered scavenger compounds

DOEpatents

Riley, W. D.; Jong, B. W.; Collins, W. K.; Gerdemann, S. J.

1994-01-01

A method of producing lithium of high purity from lithium aluminum alloys using an engineered scavenger compound, comprising: I) preparing an engineered scavenger compound by: a) mixing and heating compounds of TiO2 and Li2CO3 at a temperature sufficient to dry the compounds and convert Li.sub.2 CO.sub.3 to Li.sub.2 O; and b) mixing and heating the compounds at a temperature sufficient to produce a scavenger Li.sub.2 O.3TiO.sub.2 compound; II) loading the scavenger into one of two electrode baskets in a three electrode cell reactor and placing an Al-Li alloy in a second electrode basket of the three electrode cell reactor; III) heating the cell to a temperature sufficient to enable a mixture of KCl-LiCl contained in a crucible in the cell to reach its melting point and become a molten bath; IV) immersing the baskets in the bath until an electrical connection is made between the baskets to charge the scavenger compound with Li until there is an initial current and voltage followed by a fall off ending current and voltage; and V) making a connection between the basket electrode containing engineered scavenger compound and a steel rod electrode disposed between the basket electrodes and applying a current to cause Li to leave the scavenger compound and become electrodeposited on the steel rod electrode.

International Conference on Organometallic Chemistry (13th) Held in Torino, Europe on 4-9 September 1988. Abstracts

DTIC Science & Technology

1988-09-09

On Synthesis Of Dialkyl d-Trimethylsilyloxyalkylphosphonates Zhao Yong-Zhen and Li Zhong- Rua Dpartment o chemistry, Hua Zhong Normal University, Wuhan...Jose Vicente. Jose-AntelC hAd. Na-Yeij~xa Qhicote. Ju~an-Francisco Gutliez-Jugo. Carmen Ramirez do Arel lano. Departamento do Oulmica InordanIca...Peruzzini, Jos& Antonio Ramirez , Alberto Vacca, Francesco Vizza and Fabrizio Zanobini, Istituto per lo Studio della Stereochimica ed Energetica dei

Ultralong Lifespan and Ultrafast Li Storage: Single-Crystal LiFePO4 Nanomeshes.

PubMed

Zhang, Yan; Zhang, Hui Juan; Feng, Yang Yang; Fang, Ling; Wang, Yu

2016-01-27

A novel LiFePO4 material, in the shape of a nanomesh, has been rationally designed and synthesized based on the low crystal-mismatch strategy. The LiFePO4 nanomesh possesses several advantages in morphology and crystal structure, including a mesoporous structure, its crystal orientation that is along the [010] direction, and a shortened Li-ion diffusion path. These properties are favorable for their application as cathode in Li-ion batteries, as these will accelerate the Li-ion diffusion rate, improve the Li-ion exchange between the LiFePO4 nanomesh and the electrolyte, and reduce the Li-ion capacitive behavior during Li intercalation. So the LiFePO4 nanomesh exhibits a high specific capacity, enhanced rate capability, and strengthened cyclability. The method developed here can also be extended to other similar systems, for instance, LiMnPO4 , LiCoPO4 , and LiNiPO4 , and may find more applications in the designed synthesis of functional materials. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

First Principles Investigation of Li/Fe-Oxide as a High Energy Material for Hybrid All-in-One Li-ion/Li-O2 Batteries

NASA Astrophysics Data System (ADS)

Kinaci, Alper; Trahey, Lynn; Thackeray, Michael M.; Kirklin, Scott; Wolverton, Christopher; Chan, Maria K. Y.; CenterElectrical Energy Storage Collaboration

2014-03-01

We recently introduced a vision for high energy all-in-one electrode/electrocatalyst materials that can be used in hybrid Li-ion/Li-O2 (Li-air) cells. Recent experiments using Li5FeO4 demonstrated substantially smaller voltage polarizations and hence higher energy efficiency compared to standard Li-O2 cells forming Li2O2. The mechanism by which the charge process activates the Li5FeO4, however, is not well understood. Here, we present first principles density functional theory (DFT) calculations to establish the thermodynamic conditions for the extraction of Li/Li +O from Li5FeO4. A step-by-step, history-dependent, removal process has been followed and the stability of the Li and Li +O deficient samples is investigated on the basis of the energies of the extraction reactions. Various stages of Li/Li +O removal are identified, and structural changes and electronic structure evolution, as well as computed XRD, XANES, and PDF characterizations are reported.

Advanced Lithium Anodes for Li/Air and Li/Water Batteries

DTIC Science & Technology

2005-10-05

µm thick protective glass- ceramic membrane . The value of Li discharged capacity in this experiment is significantly larger than the Li thickness...polarization solid-state cell used for determination of electronic current across glass- ceramic membrane Final Report Page 27 of 45 10/05/2005...Li anode/aqueous electrolyte interface without destruction of the 50 µm thick protective glass- ceramic membrane . The thickness of the Li foil used in

The Impact of Li Grain Size on Coulombic Efficiency in Li Batteries.

PubMed

Mehdi, B Layla; Stevens, Andrew; Qian, Jiangfeng; Park, Chiwoo; Xu, Wu; Henderson, Wesley A; Zhang, Ji-Guang; Mueller, Karl T; Browning, Nigel D

2016-10-05

One of the most promising means to increase the energy density of state-of-the-art lithium Li-ion batteries is to replace the graphite anode with a Li metal anode. While the direct use of Li metal may be highly advantageous, at present its practical application is limited by issues related to dendrite growth and low Coulombic efficiency, CE. Here operando electrochemical scanning transmission electron microscopy (STEM) is used to directly image the deposition/stripping of Li at the anode-electrolyte interface in a Li-based battery. A non-aqueous electrolyte containing small amounts of H 2 O as an additive results in remarkably different deposition/stripping properties as compared to the "dry" electrolyte when operated under identical electrochemical conditions. The electrolyte with the additive deposits more Li during the first cycle, with the grain sizes of the Li deposits being significantly larger and more variable. The stripping of the Li upon discharge is also more complete, i.e., there is a higher cycling CE. This suggests that larger grain sizes are indicative of better performance by leading to more uniform Li deposition and an overall decrease in the formation of Li dendrites and side reactions with electrolyte components, thus potentially paving the way for the direct use of Li metal in battery technologies.

Garnet-type solid-state fast Li ion conductors for Li batteries: critical review.

PubMed

Thangadurai, Venkataraman; Narayanan, Sumaletha; Pinzaru, Dana

2014-07-07

Batteries are electrochemical devices that store electrical energy in the form of chemical energy. Among known batteries, Li ion batteries (LiBs) provide the highest gravimetric and volumetric energy densities, making them ideal candidates for use in portable electronics and plug-in hybrid and electric vehicles. Conventional LiBs use an organic polymer electrolyte, which exhibits several safety issues including leakage, poor chemical stability and flammability. The use of a solid-state (ceramic) electrolyte to produce all-solid-state LiBs can overcome all of the above issues. Also, solid-state Li batteries can operate at high voltage, thus, producing high power density. Various types of solid Li-ion electrolytes have been reported; this review is focused on the most promising solid Li-ion electrolytes based on garnet-type metal oxides. The first studied Li-stuffed garnet-type compounds are Li5La3M2O12 (M = Nb, Ta), which show a Li-ion conductivity of ∼10(-6) at 25 °C. La and M sites can be substituted by various metal ions leading to Li-rich garnet-type electrolytes, such as Li6ALa2M2O12, (A = Mg, Ca, Sr, Ba, Sr0.5Ba0.5) and Li7La3C2O12 (C = Zr, Sn). Among the known Li-stuffed garnets, Li6.4La3Zr1.4Ta0.6O12 exhibits the highest bulk Li-ion conductivity of 10(-3) S cm(-1) at 25 °C with an activation energy of 0.35 eV, which is an order of magnitude lower than that of the currently used polymer, but is chemically stable at higher temperatures and voltages compared to polymer electrolytes. Here, we discuss the chemical composition-structure-ionic conductivity relationship of the Li-stuffed garnet-type oxides, as well as the Li ion conduction mechanism.

Xiangkun Li | NREL

Science.gov Websites

Xiangkun Li Xiangkun Li Engineer - Energy Optimization Modeling Xiangkun.Li@nrel.gov | 303-275-4372 focus areas include renewable energy integration, energy systems optimization, and power flow modeling

The Impact of Li Grain Size on Coulombic Efficiency in Li Batteries

PubMed Central

Mehdi, B. Layla; Stevens, Andrew; Qian, Jiangfeng; Park, Chiwoo; Xu, Wu; Henderson, Wesley A.; Zhang, Ji-Guang; Mueller, Karl T.; Browning, Nigel D.

2016-01-01

One of the most promising means to increase the energy density of state-of-the-art lithium Li-ion batteries is to replace the graphite anode with a Li metal anode. While the direct use of Li metal may be highly advantageous, at present its practical application is limited by issues related to dendrite growth and low Coulombic efficiency, CE. Here operando electrochemical scanning transmission electron microscopy (STEM) is used to directly image the deposition/stripping of Li at the anode-electrolyte interface in a Li-based battery. A non-aqueous electrolyte containing small amounts of H2O as an additive results in remarkably different deposition/stripping properties as compared to the “dry” electrolyte when operated under identical electrochemical conditions. The electrolyte with the additive deposits more Li during the first cycle, with the grain sizes of the Li deposits being significantly larger and more variable. The stripping of the Li upon discharge is also more complete, i.e., there is a higher cycling CE. This suggests that larger grain sizes are indicative of better performance by leading to more uniform Li deposition and an overall decrease in the formation of Li dendrites and side reactions with electrolyte components, thus potentially paving the way for the direct use of Li metal in battery technologies. PMID:27703188

The Impact of Li Grain Size on Coulombic Efficiency in Li Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mehdi, B. Layla; Stevens, Andrew; Qian, Jiangfeng

One of the most promising means to increase the energy density of state-of-the-art lithium (Li)-ion batteries is to replace the graphite anode with a Li metal anode1, 2, 3. While the direct use of Li metal may be highly advantageous4,5, at present its practical application is limited by issues related to dendrite growth and low Coulombic efficiency (CE)6. Here operando electrochemical scanning transmission electron microscopy (STEM) is used to directly image the deposition/stripping of Li at the anode-electrolyte interface in a Li-based battery. A non-aqueous electrolyte containing small amounts of H2O as an additive results in remarkably different deposition/stripping propertiesmore » as compared to the "dry" electrolyte when operated under identical electrochemical conditions. The electrolyte with the additive deposits more Li during the first cycle, with the grain sizes of the Li deposits being significantly larger and more variable. The stripping of the Li upon discharge is also more complete, i.e., there is a higher cycling CE. This suggests that larger grain sizes are indicative of better performance by leading to more uniform Li deposition and an overall decrease in the formation of Li dendrites and side reactions with electrolyte components, thus potentially paving the way for the direct use of Li metal in battery technologies.« less

Epidemics in Ming and Qing China: Impacts of changes of climate and economic well-being.

PubMed

Pei, Qing; Zhang, David D; Li, Guodong; Winterhalder, Bruce; Lee, Harry F

2015-07-01

We investigated the mechanism of epidemics with the impacts of climate change and socio-economic fluctuations in the Ming and Qing Dynasties in China (AD 1368-1901). Using long-term and high-quality datasets, this study is the first quantitative research that verifies the 'climate change → economy → epidemics' mechanism in historical China by statistical methods that include correlation analysis, Granger causality analysis, ARX, and Poisson-ARX modeling. The analysis provides the evidences that climate change could only fundamentally lead to the epidemics spread and occurrence, but the depressed economic well-being is the direct trigger of epidemics spread and occurrence at the national and long term scale in historical China. Moreover, statistical modeling shows that economic well-being is more important than population pressure in the mechanism of epidemics. However, population pressure remains a key element in determining the social vulnerability of the epidemics occurrence under climate change. Notably, the findings not only support adaptation theories but also enhance our confidence to address climatic shocks if economic buffering capacity can be promoted steadily. The findings can be a basis for scientists and policymakers in addressing global and regional environmental changes. Copyright © 2015 Elsevier Ltd. All rights reserved.

NiaoDuQing granules relieve chronic kidney disease symptoms by decreasing renal fibrosis and anemia

PubMed Central

Wang, Xu; Yu, Suyun; Jia, Qi; Chen, Lichuan; Zhong, Jinqiu; Pan, Yanhong; Shen, Peiliang; Shen, Yin; Wang, Siliang; Wei, Zhonghong; Cao, Yuzhu; Lu, Yin

2017-01-01

NiaoDuQing (NDQ) granules, a traditional Chinese medicine, has been clinically used in China for over fourteen years to treat chronic kidney disease (CKD). To elucidate the mechanisms underlying the therapeutic benefits of NDQ, we designed an approach incorporating chemoinformatics, bioinformatics, network biology methods, and cellular and molecular biology experiments. A total of 182 active compounds were identified in NDQ granules, and 397 putative targets associated with different diseases were derived through ADME modelling and target prediction tools. Protein-protein interaction networks of CKD-related and putative NDQ targets were constructed, and 219 candidate targets were identified based on topological features. Pathway enrichment analysis showed that the candidate targets were mostly related to the TGF-β, the p38MAPK, and the erythropoietin (EPO) receptor signaling pathways, which are known contributors to renal fibrosis and/or renal anemia. A rat model of CKD was established to validate the drug-target mechanisms predicted by the systems pharmacology analysis. Experimental results confirmed that NDQ granules exerted therapeutic effects on CKD and its comorbidities, including renal anemia, mainly by modulating the TGF-β and EPO signaling pathways. Thus, the pharmacological actions of NDQ on CKD symptoms correlated well with in silico predictions. PMID:28915563

Electrochemical behavior of Li/LiV3O8 secondary cells

NASA Astrophysics Data System (ADS)

Bak, Hyo Rim; Lee, Jae Ha; Kim, Bok Ki; Yoon, Woo Young

2013-03-01

Li/LiV3O8 secondary cells with Li-foil and Li-powder anodes were fabricated, and their electrical properties were compared. Using the powder anode, a cell with an initial discharge capacity of 260 mAh g-1 that could be operated for over 100 cycles was obtained. The porous Li-powder electrode was safely synthesized by pressing an emulsion droplet onto an SUS mesh. A threefold increase in the electrical conductivity of the LiV3O8 cathode was achieved by the addition of carbon using a vibration pot mill. Using the powder anode resulted in 80% capacity retention at the 100th cycle, while that using the foil electrode was 46%; the 1.0 Crate/ 0.1 C-rate capacity ratio also increased from 44% to 60%. A cell employing the LiV3O8-carbon composite cathode showed better electrical performance, a capacity retention of 90% after 50 cycles, and an increase in rate capacity ratio. The crystal structure and morphology of the LiV3O8-C composite were investigated by x-ray diffraction and scanning electron microscopy.

Theoretical study of LiK and LiK+ in adiabatic representation

NASA Astrophysics Data System (ADS)

Al-dossary, Omar M.; Khelifi, Neji

2014-01-01

The potential energy curves have been calculated for the electronic states of the molecule LiK within the range 3 to 300 a.u., of the internuclear distance R. Using an ab initio method, through a semiempirical spin-orbit pseudo-potential for the Li (1 s 2) and K (1 s 22 s 22 p 63 s 23 p 6) cores and core valence correlation correction added to the electrostatic Hamiltonian with Gaussian basis sets for both atoms. The core valence effects including core-polarization and core-valence correlation are taken into account by using an l-dependent core-polarization potential. The molecular orbitals have been derived from self-consistent field (SCF) calculation. The spectroscopic constants, dipole moments and vibrational levels of the lowest electronic states of the LiK molecule dissociating into K (4 s, 4 p, 5 s, 3 d, and 5 p) + Li (2 s, 2 p, 3 s, and 3 p) in 1, 3Σ, 1, 3Π, and 1, 3Δ symmetries. Adiabatic results are also reported for 2Σ, 2Π, and 2Δ electronic states of the molecular ion LiK+ dissociating into Li (2 s, 2 p, 3 s, and 3 p) + K+ and Li+ + K (4 s, 4 p, 5 s, 3 d, and 5 p). The comparison of the present results with those available in the literature shows a very good agreement in spectroscopic constants of some lowest states of the LiK and LiK+ molecules, especially with the available theoretical works. The existence of numerous avoided crossing between electronic states of 2Σ and 2Π symmetries is related to the charge transfer process between the two ionic systems Li+K and LiK+.

Tuning Features of Chinese Folk Song Singing: A Case Study of Hua'er Music.

PubMed

Yang, Yang; Welch, Graham; Sundberg, Johan; Himonides, Evangelos

2015-07-01

The learning and teaching of different singing styles, such as operatic and Chinese folk singing, was often found to be very challenging in professional music education because of the complexity of varied musical properties and vocalizations. By studying the acoustical and musical parameters of the singing voice, this study identified distinctive tuning characteristics of a particular folk music in China-Hua'er music-to inform the ineffective folk singing practices, which were hampered by the neglect of inherent tuning issues in music. Thirteen unaccompanied folk song examples from four folk singers were digitally audio recorded in a sound studio. Using an analyzing toolkit consisting of Praat, PeakFit, and MS Excel, the fundamental frequencies (F0) of these song examples were extracted into sets of "anchor pitches" mostly used, which were further divided into 253 F0 clusters. The interval structures of anchor pitches within each song were analyzed and then compared across 13 examples providing parameters that indicate the tuning preference of this particular singing style. The data analyses demonstrated that all singers used a tuning pattern consisting of five major anchor pitches suggesting a nonequal-tempered bias in singing. This partly verified the pentatonic scale proposed in previous empirical research but also argued a potential misunderstanding of the studied folk music scale that failed to take intrinsic tuning issues into consideration. This study suggests that, in professional music training, any tuning strategy should be considered in terms of the reference pitch and likely tuning systems. Any accompanying instruments would need to be tuned to match the underlying tuning bias. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Investigation of the role of 10Li resonances in the halo structure of 11Li through the 11Li (p , d)10Li transfer reaction

NASA Astrophysics Data System (ADS)

Sanetullaev, A.; Kanungo, R.; Tanaka, J.; Alcorta, M.; Andreoiu, C.; Bender, P.; Chen, A. A.; Christian, G.; Davids, B.; Fallis, J.; Fortin, J. P.; Galinski, N.; Gallant, A. T.; Garrett, P. E.; Hackman, G.; Hadinia, B.; Ishimoto, S.; Keefe, M.; Krücken, R.; Lighthall, J.; McNeice, E.; Miller, D.; Purcell, J.; Randhawa, J. S.; Roger, T.; Rojas, A.; Savajols, H.; Shotter, A.; Tanihata, I.; Thompson, I. J.; Unsworth, C.; Voss, P.; Wang, Z.

2016-04-01

The first measurement of the one-neutron transfer reaction 11Li(p,d)10Li performed using the IRIS facility at TRIUMF with a 5.7 A MeV11Li beam interacting with a solid H2 target is reported. The 10Li residue was populated strongly as a resonance peak with energy Er = 0.62 ± 0.04 MeV having a total width Γ = 0.33 ± 0.07 MeV. The angular distribution of this resonance is characterized by neutron occupying the 1p1/2 orbital. A DWBA analysis yields a spectroscopic factor of 0.67 ± 0.12 for p1/2 removal strength from the ground state of 11Li to the region of the peak.

The Interstellar 7Li/6Li Ratio in the Diffuse Gas Near IC 443

NASA Astrophysics Data System (ADS)

Ritchey, A. M.; Taylor, C. J.; Federman, S. R.; Lambert, D. L.

2010-11-01

Supernova remnants are believed to be the primary acceleration sites of Galactic cosmic rays (GCR), which are essential to gas-phase interstellar chemistry since they are a major source of ionization in both diffuse and dense environments. The interaction of accelerated particles with interstellar gas will also synthesize isotopes of the light elements Li, Be, and B through the spallation of CNO nuclei (producing all stable LiBeB isotopes) and through α+α fusion (yielding 6Li and 7Li, only). Type II supernovae may provide an additional source of 7Li and 11B during core collapse through neutrino-induced spallation in the He and C shells of the progenitor star (the ν-process). However, direct observational evidence for light element synthesis resulting from cosmic-ray or neutrino-induced spallation is rare. Here, we examine 7Li/6Li isotope ratios along four lines of sight through the supernova remnant IC 443 using observations of the Li I λ6707 doublet made with the Hobby-Eberly Telescope (HET) at McDonald Observatory. The 7Li/6Li ratio in the general interstellar medium is expected to be similar to the ratio of ~12 that characterizes solar system material. A local enhancement in the cosmic-ray flux will act to lower 7Li/6Li, yielding a ratio of ~2 when cosmic rays dominate Li synthesis. Gamma-ray emission from IC 443 provides strong evidence for the interaction of cosmic rays accelerated by the remnant with the ambient atomic and molecular gas. Yet this material has also been contaminated by the ejecta of a Type II supernova, which should be enriched in 7Li. We are seeking 7Li/6Li ratios that are either higher than the solar system ratio as a result of the ν-process or lower due to cosmic-ray spallation. Since the fine structure separation of the Li I doublet is comparable to the isotope shift (~7 km s-1) and each fine structure line is further split into hyperfine components, the velocity structure along the line of sight must be carefully constrained if

Li isotopes in archean zircons

NASA Astrophysics Data System (ADS)

Bouvier, A.; Ushikubo, T.; Kita, N.; Cavosie, A. J.; Kozdon, R.; Valley, J. W.

2009-12-01

Li is a fluid mobile, moderately incompatible element with a large mass difference between its two stable isotopes. Different processes can fractionate 7Li/6Li (fluid-rock interaction, metamorphic reactions, and Li diffusion), leading to variation by over 50‰ of δ7Li for common crustal material. These large variations make δ7Li a potential tracer of continental weathering and of the fluids affecting magma sources. Here, we report δ7Li and trace elements in Archean igneous zircons from TTG and sanukitoid granitoids from the Superior Province (Canada) in order to characterize Li in Archean zircons from well-described samples. These data are compared to detrital zircons from the Jack Hills (Western Australia) for which parent rock-type is uncertain. This study aims to better understand Li substitution in zircon and to evaluate the utility of δ7Li and [Li] for Archean petrogenesis. Zircons (n=71) were analyzed for δ7Li and trace elements (Li, P, Ca, Ti, V, Fe, Y, REE, U, Th) using an IMS-1280 ion microprobe. Most of the zircons display typical igneous REE patterns and zoning by CL. [Li] averages 13.1 ± 9 for TTG, 25.7 ± 19 for Sanukitoid and 31.0 ± 14 ppm for Jack Hills zircons, which are distinct from mantle-related zircons (<0.1 ppm). Values of δ7Li average 1.0 ± 4.5‰ for TTGs, 6.3 ± 4.4‰ for sanukitoids and -2.6 ± 8.8‰ for Jack Hills samples. Trace elements were analyzed from single spots in order to evaluate coupled substitutions. Atomic ratios (3Li+Y+REE)/P average 2.6, showing that Li and trivalent atoms are not charge-balanced by P, and suggesting that Li does not replace Zr, according to the xenotime substitution. However, (Y+REE)/(Li+P) atomic ratios average 1.0 ± 0.6, supporting the hypothesis that Li is interstitial and partly compensates trivalent cations. Several observations in this study suggest that [Li] is primary in the studied zircons: i) if Li is interstitial, charge-balance and slow diffusion of REE would control Li mobility

Investigation of the role of 10Li resonances in the halo structure of 11Li through the 11Li(p,d)10Li transfer reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanetullaev, A.; Kanungo, R.; Tanaka, J.

2016-03-02

Here, the first measurement of the one-neutron transfer reaction 11Li(p,d) 10Li performed using the IRIS facility at TRIUMF with a 5.7A MeV 11Li beam interacting with a solid H 2 target is reported. The 10Li residue was populated strongly as a resonance peak with energy E r = 0.62 ± 0.04 MeV having a total width Γ = 0.33 ± 0.07 MeV. The angular distribution of this resonance is characterized by neutron occupying the 1p 1/2 orbital. A DWBA analysis yields a spectroscopic factor of 0.67 ± 0.12 for p 1/2 removal strength from the ground state of 11Li tomore » the region of the peak.« less

G-LiHT: Goddard's LiDAR, Hyperspectral and Thermal Airborne Imager

NASA Technical Reports Server (NTRS)

Cook, Bruce; Corp, Lawrence; Nelson, Ross; Morton, Douglas; Ranson, Kenneth J.; Masek, Jeffrey; Middleton, Elizabeth

2012-01-01

Scientists at NASA's Goddard Space Flight Center have developed an ultra-portable, low-cost, multi-sensor remote sensing system for studying the form and function of terrestrial ecosystems. G-LiHT integrates two LIDARs, a 905 nanometer single beam profiler and 1550 nm scanner, with a narrowband (1.5 nanometers) VNIR imaging spectrometer and a broadband (8-14 micrometers) thermal imager. The small footprint (approximately 12 centimeters) LIDAR data and approximately 1 meter ground resolution imagery are advantageous for high resolution applications such as the delineation of canopy crowns, characterization of canopy gaps, and the identification of sparse, low-stature vegetation, which is difficult to detect from space-based instruments and large-footprint LiDAR. The hyperspectral and thermal imagery can be used to characterize species composition, variations in biophysical variables (e.g., photosynthetic pigments), surface temperature, and responses to environmental stressors (e.g., heat, moisture loss). Additionally, the combination of LIDAR optical, and thermal data from G-LiHT is being used to assess forest health by sensing differences in foliage density, photosynthetic pigments, and transpiration. Low operating costs (approximately $1 ha) have allowed us to evaluate seasonal differences in LiDAR, passive optical and thermal data, which provides insight into year-round observations from space. Canopy characteristics and tree allometry (e.g., crown height:width, canopy:ground reflectance) derived from G-LiHT data are being used to generate realistic scenes for radiative transfer models, which in turn are being used to improve instrument design and ensure continuity between LiDAR instruments. G-LiHT has been installed and tested in aircraft with fuselage viewports and in a custom wing-mounted pod that allows G-LiHT to be flown on any Cessna 206, a common aircraft in use throughout the world. G-LiHT is currently being used for forest biomass and growth estimation

Investigations of Li-containing SiCN(O) ceramics via 7Li MAS NMR.

PubMed

Gumann, Sina; Nestle, Nikolaus; Liebau-Kunzmann, Verena; Riedel, Ralf

2007-04-01

Lithium-containing silicon (oxy)carbonitride ceramics (SiCN(O):Li) were synthesized via precursor-to-ceramic-transformation of Li-containing (poly)silazanes. The precursors were obtained by lithiation of 2,4,6-trimethyl-2,4,6-trivinylcyclotrisilazane with n-butyllithium and by reaction of a commercial poly(organosilazane) VL20 with metallic lithium. The annealing treatment was carried out at temperatures between 200 and 1400 degrees C in argon (DeltaT=200 degrees C) and yielded Li-containing silicon (oxy)carbonitride. X-ray powder diffraction revealed that the resulting SiCN(O):Li ceramics were basically amorphous up to temperatures of 1000 degrees C and formed LiSi(2)N(3), graphite and silicon carbide as crystalline phases at higher temperatures. (7)Li MAS NMR spectroscopy was carried out to investigate the structure of the Li-containing phases and to study the reaction path of metallic Li with polysilazane. Based on the NMR spectra, there is almost no difference found in the chemical shift of the SiCN(O):Li ceramics obtained at different temperatures. Accordingly, Li is assigned to be mainly coordinated to N and O present as contaminant element. Relaxation time measurements showed that the most mobile Li(+) species seems to be present in the product obtained in the pyrolysis temperature range between 600 and 1000 degrees C.

Electrochemical performance of LiNi0.4Co0.2Mn0.4O2 prepared by different molten salt flux: LiNO3-LiCl and LiNO3-KNO3

NASA Astrophysics Data System (ADS)

Satyanarayana, M.; James, Joseph; U. V., Varadaraju

2017-10-01

LiNi0.4Co0.2Mn0.4O2 material synthesized at different temperatures by using LiNO3-LiCl and LiNO3-KNO3 molten salt as a reaction medium. The phase purity of the samples obtained by powder X-ray diffraction measurement which suggests layered α-NaFeO2 type is obtained at 800-900 °C using LiNO3-LiCl flux and at 750-850 °C using LiNO3-KNO3 flux. The surface morphology change with flux media at different temperature are obtained by scanning electron microscopy analysis. The galvanostatic cycling results show that the high stable reversible discharge capacity of 155 (±3) mAh g-1 obtained for treated compound at 900 °C for 1 h (using LiNO3-LiCl) with coloumbic efficiency of 99%. The reversible discharge capacity of 140 and 130 (±3) mAh g-1 obtained for treated compound at 750 and 850 °C, respectively (using LiNO3-KNO3).

Experimental study of the effect of polyanionic cellulose on process of filtrate loss of low-solids drilling fluid

NASA Astrophysics Data System (ADS)

yang, P.

2013-12-01

Experimental study of the effect of polyanionic cellulose on process of filtrate loss of low-solids drilling fluid Ping Yang 1,2, Min-hui Wu2, Xue-wen Zhu2, Tao Deng2, Xue-qing Sun2 1. Key Laboratory of Geotechnical and Underground Engineering of Ministry of Education, Tongji University, Shanghai 200092,China 2. Department of Geotechnical Engineering,Tongji University,Shanghai 200092,China Abstract The process of filtrate loss of low-solids drilling fluid was tested by changing the polyanionic cellulose content in low-solids drilling fluid. The effect of polyanionic cellulose on process of filtrate loss of low-solids drilling fluid was analyzed. The test results showed that when time of filtration is same, the volume of filtrate loss decreases linearly with increasing polyanionic cellulose content. When polyanionic cellulose content is same, the rate of filtrate loss decreases nonlinearly with increasing time and the rate of filtrate loss will reach a stable value.The volume of filtrate loss in 7 to 8 minutes can reaches half of the total volume of filtrate loss. At the same time, the rate of filtrate loss of drilling fluid decreases nonlinearly with increasing viscosity.When the apparent viscosity is between 3.5~4.15 MPa.s, decrease speed of rate of filtrate loss of drilling fluid is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss. Keyword Polyanionic Cellulose,Drilling Fluid,Process of Filtrate Loss Acknowledgments This investigation was supported by the National Natural Science Foundation of China (projects No. 41002093 and 41072205); the Fundamental Research Funds for the Central Universities; the Shanghai Leading Academic Discipline Project (project No. B308), Tongji University; and the Program for Young Excellent Talents, Tongji University. The authors are extremely grateful for the financial support from these five organizations.

Metallic Li colloids studied by Li-7 MAS NMR in electron-irradiated LiF

NASA Astrophysics Data System (ADS)

Zogal, O. J.; Beuneu, F.; Vajda, P.; Florian, P.; Massiot, D.

Li-7 MAS NMR spectra of 2.5 MeV electron-irradiated LiF crystals have been measured in a field of 9.4 T. Besides the resonance line of the ionic compound, a second well-separated spectrum is observed in the region of the Knight shift value for metallic lithium. At room temperature, the latter can be decomposed into two components with different Knight shift and linewidth values. When the temperature is increased, line narrowing takes place at first, indicating shortening of correlation times for self-diffusion, independently in both components. Above 370 K, both lines broaden and approach each other before collapsing into a single line. The high ppm component disappears after crossing the melting temperature of metallic lithium (454 K). The two lines are attributed to different types of metallic Li: one to bulk-like metal, the other to Li present initially under pressure and relaxing to the former under thermal treatment.

Li plating as unwanted side reaction in commercial Li-ion cells - A review

NASA Astrophysics Data System (ADS)

Waldmann, Thomas; Hogg, Björn-Ingo; Wohlfahrt-Mehrens, Margret

2018-04-01

Deposition of Lithium metal on anodes contributes significantly to ageing of Li-ion cells. Lithium deposition is connected not only to a drastic limitation of life-time, but also to fast-charging capability and safety issues. Lithium deposition in commercial Li-ion cells is not limited to operation conditions at low temperatures. In recent publications various types of commercial cells were investigated using complimentary analysis methods. Five cell types studied in literature (18650, 26650, pouch) serve as a basis for comparison when and why Li deposition happens in commercial Li-ion cells. In the present paper, we reviewed literature on (i) causes, (ii) hints and evidences for Li deposition, (iii) macroscopic morphology of Li deposition/plating, (iv) ageing mechanisms and shapes of capacity fade curves involving Li deposition, and (v) influences of Li deposition on safety. Although often discussed, safety issues regarding Li deposition are not only limited to dendrite growth and internal short circuits, but also to exothermic reactions in the presence of Lithium metal. Furthermore, we tried to connect knowledge from different length scales including the macroscopic level (Li-ion cells, operating conditions, gradients in cells, electrochemical tests, safety tests), the microscopic level (electrodes, particles, microstructure), and the atomic level (atoms, ions, molecules, energy barriers).

Insights into the Li Intercalation and SEI Formation on LiSi Nanoclusters

DOE PAGES

Hankins, Kie; Soto, Fernando A.; Balbuena, Perla B.

2017-01-01

We report a first-principles atomic level assessment of the lithiation and reactivity of pre-lithiated Si clusters. Density functional theory formation energy calculations reveal that the pre-lithiated Li 16Si 16 cluster exposed to two different Li fluxes can store Li between the concentrations of Li 2.5Si and Li 3.5Si. This increase in storage capacity is attributed to the start of an amorphization process in the cluster, and more importantly these results show that the intercalation reaction can be controlled by the flux of the Li-ions. However, in a real battery, the lithiation of the anode occurs simultaneously to the electrode-electrolyte reactions.more » Here we simulate the solid-electrolyte interphase (SEI) formation and simultaneous lithiation of a Li 16Si 16 cluster in contact with two different electrolyte solutions: one with pure ethylene carbonate (EC), and another with a 1 M solution of LiPF 6 in EC. Our ab initio molecular dynamics simulations show that the solvent and salt are decomposed leading to the initial stages of the SEI layer formation and large part of the added Li becomes part of the SEI. Interestingly, the pure EC solution results in lower storage capacity and higher reactivity, whereas the presence of the salt causes the opposite effect: higher lithiation and reduced reactivity.« less

Electrochemical performances of LiMnPO4 synthesized from non-stoichiometric Li/Mn ratio.

PubMed

Xiao, Jie; Chernova, Natasha A; Upreti, Shailesh; Chen, Xilin; Li, Zheng; Deng, Zhiqun; Choi, Daiwon; Xu, Wu; Nie, Zimin; Graff, Gordon L; Liu, Jun; Whittingham, M Stanley; Zhang, Ji-Guang

2011-10-28

In this paper, the influences of the lithium content in the starting materials on the final performances of as-prepared Li(x)MnPO(4) (x hereafter represents the starting Li content in the synthesis step which does not necessarily mean that Li(x)MnPO(4) is a single phase solid solution in this work.) are systematically investigated. It has been revealed that Mn(2)P(2)O(7) is the main impurity when Li < 1.0 while Li(3)PO(4) begins to form once x > 1.0. The interactions between Mn(2)P(2)O(7) or Li(3)PO(4) impurities and LiMnPO(4) are studied in terms of the structural, electrochemical, and magnetic properties. At a slow rate of C/50, the reversible capacity of both Li(0.5)MnPO(4) and Li(0.8)MnPO(4) increases with cycling. This indicates a gradual activation of more sites to accommodate a reversible diffusion of Li(+) ions that may be related to the interaction between Mn(2)P(2)O(7) and LiMnPO(4) nanoparticles. Among all of the different compositions, Li(1.1)MnPO(4) exhibits the most stable cycling ability probably because of the existence of a trace amount of Li(3)PO(4) impurity that functions as a solid-state electrolyte on the surface. The magnetic properties and X-ray absorption spectroscopy (XAS) of the MnPO(4)·H(2)O precursor, pure and carbon-coated Li(x)MnPO(4) are also investigated to identify the key steps involved in preparing a high-performance LiMnPO(4). This journal is © the Owner Societies 2011

Mechanistic insights of Li+ diffusion within doped LiFePO4 from Muon Spectroscopy.

PubMed

Johnson, Ian D; Ashton, Thomas E; Blagovidova, Ekaterina; Smales, Glen J; Lübke, Mechthild; Baker, Peter J; Corr, Serena A; Darr, Jawwad A

2018-03-07

The Li + ion diffusion characteristics of V- and Nb-doped LiFePO 4 were examined with respect to undoped LiFePO 4 using muon spectroscopy (µSR) as a local probe. As little difference in diffusion coefficient between the pure and doped samples was observed, offering D Li values in the range 1.8-2.3 × 10 -10  cm 2 s -1 , this implied the improvement in electrochemical performance observed within doped LiFePO 4 was not a result of increased local Li + diffusion. This unexpected observation was made possible with the µSR technique, which can measure Li + self-diffusion within LiFePO 4 , and therefore negated the effect of the LiFePO 4 two-phase delithiation mechanism, which has previously prevented accurate Li + diffusion comparison between the doped and undoped materials. Therefore, the authors suggest that µSR is an excellent technique for analysing materials on a local scale to elucidate the effects of dopants on solid-state diffusion behaviour.

Layered Li-Mn-M-oxides as cathodes for Li-ion batteries:. Recent trends

NASA Astrophysics Data System (ADS)

Shaju, K. M.; Subba Rao, G. V.; Chowdari, B. V. R.

2002-12-01

There is an increasing demand for manganese (Mn) based mixed oxides which can effectively replace the presently used LiCoO2 as cathode in Li-ion batteries (LIB). The well-studied spinel, LiMn2O4 and its doped derivatives give a capacity of 100-120 mAh/g, but show capacity-fading on cycling especially above 55°C. The layered LiMnO2, isostructural to LiCoO2 (so called O3-structure) can be a viable cathode. However, studies have shown that it undergoes conversion to spinel structure on cycling and thus gives capacity-fading. Other alternative systems recently studied are: O2-structured layered Li-M-Mn-oxides with the general formula Li(2/3)+x(MyMn1-y)O2, M = Li, Ni, Co; x ≤ 0.33 and y = 0.1-0.67, O3-Li(Ni1/2Mn1/2)O2, Li(NixCo1-2xMnx)O2, and M'-substituted Li2MnO3 (M' = Ni, Co, Cr). Some of them are shown to have stable cycling performance, good rate-capability and structural stability over charge-discharge cycling in the 2.5-4.6 V region. Further, the electrochemical processes in the above mixed oxides have been shown to involve Ni2+/4+ or Cr3+/6+ redox couple, thus invoking novel ideas to develop new cathode materials. A brief review of the work done on the above O2- and O3-layered Li-Mn-M-oxides (M = metal) as cathodes for LIB is presented.

Ab initio identification of the Li-rich phase in LiFePO4.

PubMed

Zeng, Hua; Gu, Yue; Teng, Gaofeng; Liu, Yimeng; Zheng, Jiaxin; Pan, Feng

2018-06-27

A recent discovery of anionic redox activity in Li-rich layered compounds opens a new direction for the design of high-capacity cathode materials for lithium-ion batteries. Here using extensive ab initio calculations, the thermodynamic existence of the Li-rich phase in LiFePO4 to form Li1+xFe1-xPO4 with x not exceeding 12.5% has been proved. Anionic redox activity and structural stability during delithiation are further investigated. Interestingly, it is found that Li1+xFe1-xPO4 cannot be delithiated completely and thus cannot achieve extra capacity by anionic redox activity, because the local oxygen-ion redox will cause the fracture of the rigid framework formed by phosphate tetrahedral polyanions. Although an extra capacity cannot be realized, the excess Li-ions at Fe sites can enhance the Li-ion diffusivity along the adjacent [010] channel and contribute to the shift from 1D to 2D/3D diffusion. This study provides a fresh perspective on olivine-type LiFePO4 and offers some important clues on designing Li-rich cathode materials with high energy density.

Computational Studies of Solubilities of LiO 2 and Li 2O 2 in Aprotic Solvents

DOE PAGES

Cheng, Lei; Redfern, Paul; Lau, Kah Chun; ...

2017-08-12

Knowledge of the solubilities of Li 2O 2 and LiO 2 in aprotic solvents is important for insight into the discharge and charge processes of Li-O 2 batteries, but these quantities are not well known. In this contribution, the solvation free energies of molecular LiO 2 and Li 2O 2 in various organic solvents were calculated using various explicit and implicit solvent models, as well as ab initio molecular dynamics (AIMD) methods. Best estimates for the solvation energies from these calculations along with calculated lattice energies of Li 2O 2 and LiO 2 were used to determine the solubility ofmore » bulk LiO 2 and Li 2O 2. The computed solubility of LiO 2 (1.8 × 10 -2 M) is about 15 orders higher than that of Li 2O 2 (2.0 × 10 -17 M) due to a much less negative lattice energy of bulk LiO 2 compared to that of Li 2O 2. The difference in solubilities between LiO 2 and Li 2O 2 likely will affect the nucleation and growth mechanisms and resulting morphologies of the products formed during battery discharge, influencing the performance of the battery cell. In conclusion, the calculated LiO 2 and Li 2O 2 solubilities provide important information for fundamental studies of discharge and charge chemistries in Li-O 2 batteries.« less

Computational Studies of Solubilities of LiO 2 and Li 2O 2 in Aprotic Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Lei; Redfern, Paul; Lau, Kah Chun

Knowledge of the solubilities of Li 2O 2 and LiO 2 in aprotic solvents is important for insight into the discharge and charge processes of Li-O 2 batteries, but these quantities are not well known. In this contribution, the solvation free energies of molecular LiO 2 and Li 2O 2 in various organic solvents were calculated using various explicit and implicit solvent models, as well as ab initio molecular dynamics (AIMD) methods. Best estimates for the solvation energies from these calculations along with calculated lattice energies of Li 2O 2 and LiO 2 were used to determine the solubility ofmore » bulk LiO 2 and Li 2O 2. The computed solubility of LiO 2 (1.8 × 10 -2 M) is about 15 orders higher than that of Li 2O 2 (2.0 × 10 -17 M) due to a much less negative lattice energy of bulk LiO 2 compared to that of Li 2O 2. The difference in solubilities between LiO 2 and Li 2O 2 likely will affect the nucleation and growth mechanisms and resulting morphologies of the products formed during battery discharge, influencing the performance of the battery cell. In conclusion, the calculated LiO 2 and Li 2O 2 solubilities provide important information for fundamental studies of discharge and charge chemistries in Li-O 2 batteries.« less

Li14P2O3N6 and Li7PN4: Computational study of two nitrogen rich crystalline LiPON electrolyte materials

NASA Astrophysics Data System (ADS)

Al-Qawasmeh, Ahmad; Holzwarth, N. A. W.

2017-10-01

Two lithium oxonitridophosphate materials are computationally examined and found to be promising solid electrolytes for possible use in all solid-state batteries having metallic Li anodes - Li14P2O3N6 and Li7PN4. The first principles simulations are in good agreement with the structural analyses reported in the literature for these materials and the computed total energies indicate that both materials are stable with respect to decomposition into binary and ternary products. The computational results suggest that both materials are likely to form metastable interfaces with Li metal. The simulations also find both materials to have Li ion migration activation energies comparable or smaller than those of related Li ion electrolyte materials. Specifically, for Li7PN4, the experimentally measured activation energy can be explained by the migration of a Li ion vacancy stabilized by a small number of O2- ions substituting for N3- ions. For Li14P2O3N6, the activation energy for Li ion migration has not yet been experimentally measured, but simulations predict it to be smaller than that measured for Li7PN4.

The emergence of the ecological mind in Hua-Yen/Kegon Buddhism and Jungian psychology.

PubMed

Cambray, Joe

2017-02-01

The complexity associated with deep interconnectedness in nature is beginning to be articulated and elaborated in the field of ecological studies. While some parallels to the psyche have been made and the field of Eco-psychology has been developing, Jung's explicit contribution by way of the image of rhizomes has not been considered in detail. Philosopher Gilles Deleuze acknowledges borrowing the term from Jung, though he disagreed with Jung's Empedoclean use of the term. The paper presents some fundamental properties of rhizomes along with contemporary scientific research on mycorrhizal (fungal) networks. Comparisons are made, first with classical symbolic forms, demonstrating some overlap but also some differences. Then comparison of rhizomal networks is made to those found both in mammalian brains and in recent images of the 'cosmic web'. While no hard conclusions can be drawn from these images, their remarkable similarities are suggestive of a need to reconsider what is meant by 'intelligence'. The cosmic web is one of the largest structures in the known universe (clusters of galaxies which form into filaments and walls) with empty spaces in between. Exploration of the structure of this web leads to a discussion of dark matter and dark energy, current hot topics in science, probing into the mysteries of our 'Big-Bang' cosmology. An additional comparison of the emerging image of the universe as a whole with the ancient Chinese Buddhist cosmological vision from the Hua-Yen School (Kegon in Japan) again reveals profound parallels. The potential convergence of aspects of subjective, or meditative, explorations with objective scientific constructions is striking and offers links between East and West, as well as potential confirmation of the objective aspects of empathy. © 2017, The Society of Analytical Psychology.

Solution-processable glass LiI-Li 4SnS 4 superionic conductors for all-solid-state Li-ion batteries

DOE PAGES

Kern Ho Park; Oh, Dae Yang; Choi, Young Eun; ...

2015-12-22

The new, highly conductive (4.1 × 10 –4 S cm –1 at 30 °C), highly deformable, and dry-air-stable glass 0.4LiI-0.6Li 4SnS 4 is prepared using a homogeneous methanol solution. Furthermore, the solution process enables the wetting of any exposed surface of the active materials with highly conductive solidified electrolytes (0.4LiI-0.6Li 4SnS 4), resulting in considerable improvements in electrochemical performances of these electrodes over conventional mixture electrodes.

Li and δ 7Li in mudrocks from the British Caledonides: Metamorphism and source influences

NASA Astrophysics Data System (ADS)

Qiu, Lin; Rudnick, Roberta L.; McDonough, William F.; Merriman, Richard J.

2009-12-01

Mudrocks from three lower Paleozoic basins in the British Caledonides (southern Lake District, northern Lake District and Southern Uplands) were investigated to determine the influence of sub-greenschist facies metamorphism on Li and the factors that control Li in fine-grained terrigenous sedimentary rocks. Metamorphic grade, as determined by KI (Kübler index) does not correlate with Li content ([Li]) and δ 7Li, indicating that sub-greenschist facies metamorphism has negligible effect on Li in these rocks. Collectively, the data for all three basins show a negative correlation between [Li] and δ 7Li and a positive correlation between [Li] and the Chemical Index of Alteration (CIA), suggesting that provenance exerts the greatest control on Li in mudrocks. Samples from the northern Lake District, which were deposited in an extensional basin, have homogeneous REE patterns, similar to shale composites (PAAS), the highest CIA, Th/U and [Li] and the lowest δ 7Li and ɛNd, consistent with their derivation from a highly weathered, ancient continental source. By contrast, mudrocks from the Southern Uplands range to the lowest CIA, Th/U and [Li] and have the highest δ 7Li and ɛNd. These samples were deposited in a forearc basin on the southern margin of the Laurentian craton and contain volcanic detritus. Their REE patterns are the most variable, ranging from average shale-like patterns to less LREE-enriched patterns. The compositional heterogeneity within the Southern Uplands mudrocks is consistent with a mixed provenance that includes juvenile crustal materials (lower [Li], ɛNd and Th/U, higher δ 7Li), likely derived from the arc, as well as more highly weathered continental detritus. Mudrocks from the southern Lake District were deposited in a foreland basin, and exhibit geochemical characteristics intermediate between the northern Lake District and the Southern Uplands mudrocks, indicating their derivation from a mixed source. Our study shows that Li

Committees

NASA Astrophysics Data System (ADS)

2012-11-01

Leadership Team of the IAHR Committee for Hydraulic Machinery and Systems Eduard EGUSQUIZA, UPC Barcelona, Spain, Chair François AVELLAN, EPFL-LMH, Switzerland, Past Chair Richard K FISHER, Voith Hydro Inc., USA, Past Chair Fidel ARZOLA, Edelca, Venezuela Michel COUSTON, Alstom Hydro, France Niklas DAHLBÄCKCK, Vatenfall, Sweden Normand DESY, Andritz VA TECH Hydro Ltd., Canada Chisachi KATO, University of Tokyo, Japan Andrei LIPEJ, Turboinstitut, Slovenija Torbjørn NIELSEN, NTNU, Norway Romeo SUSAN-RESIGA, 'Politehnica' University Timisoara, Romania Stefan RIEDELBAUCH, Stuggart University, Germany Albert RUPRECHT, Stuttgart University, Germany Qing-Hua SHI, Dong Fang Electrical Machinery Co., China Geraldo TIAGO, Universidade Federal de Itajubá, Brazil International Advisory Committee Shouqi YUAN (principal) Jiangsu University China QingHua SHI (principal) Dong Fang Electrical Machinery Co. China Fidel ARZOLA EDELCA Venezuela Thomas ASCHENBRENNER Voith Hydro GmbH & Co. KG Germany Anton BERGANT Litostroj Power doo Slovenia B C BHAOYAL Research & Technology Centre India Hermod BREKKE NTNU Norway Stuart COULSON Voith Hydro Inc. USA Paul COOPER Fluid Machinery Research Inc USA V A DEMIANOV Power Machines OJSC Russia Bart van ESCH Technische Universiteit Eindhoven Netherland Arno GEHRER Andritz Hydro Graz Austria Akira GOTO Ebara Corporation Japan Adiel GUINZBURG The Boeing Company USA D-H HELLMANN KSB AG Germany Ashvin HOSANGADI Combustion Research and Flow Technology USA Byung-Sun HWANG Korea Institute of Material Science Korea Toshiaki KANEMOTO Kyushu Institute of Technology Japan Mann-Eung KIM Korean Register of Shipping Korea Jiri KOUTNIK Voith Hydro GmbH & Co. KG Germany Jinkook LEE Eaton Corporation USA Young-Ho LEE Korea Maritime University Korea Woo-Seop LIM Hyosung Goodsprings Inc Korea Jun MATSUI Yokohama National University Japan Kazuyoshi Mitsubishi H I Ltd, Japan MIYAGAWA Christophe NICOLET Power Vision Engineering Srl Switzerland Maryse PAGE Hydro

Elastic, dynamical, and electronic properties of LiHg and Li3Hg: First-principles study

NASA Astrophysics Data System (ADS)

Wang, Yan; Hao, Chun-Mei; Huang, Hong-Mei; Li, Yan-Ling

2018-04-01

The elastic, dynamical, and electronic properties of cubic LiHg and Li3Hg were investigated based on first-principles methods. The elastic constants and phonon spectral calculations confirmed the mechanical and dynamical stability of the materials at ambient conditions. The obtained elastic moduli of LiHg are slightly larger than those of Li3Hg. Both LiHg and Li3Hg are ductile materials with strong shear anisotropy as metals with mixed ionic, covalent, and metallic interactions. The calculated Debye temperatures are 223.5 K and 230.6 K for LiHg and Li3Hg, respectively. The calculated phonon frequency of the T2 g mode in Li3Hg is 326.8 cm-1. The p states from the Hg and Li atoms dominate the electronic structure near the Fermi level. These findings may inspire further experimental and theoretical study on the potential technical and engineering applications of similar alkali metal-based intermetallic compounds.

Indicators of Provenance Weathering: Li and δ7Li in Mudrocks from the British Caledonides

NASA Astrophysics Data System (ADS)

Qiu, L.; Rudnick, R. L.; McDonough, W. F.; Merriman, R. J.

2008-12-01

We determined the Li concentration [Li] and isotopic composition (δ7Li), as well as major, trace element and Sr and Nd isotopic compositions of mudrocks (mudstone, shale, slate) from three Lower Paleozoic basins within the British Caledonides in order to determine the effects of sub-greenschist facies metamorphism on Li and the factors that control Li in mudrocks. [Li] varies widely, from 29 to 139 ppm, with mudrocks from the northern Lake District generally having higher concentrations (56-136 ppm, average 102 ppm) than those from the Scottish Southern Uplands (28-74 ppm, average 50 ppm) or southern Lake District (40-91 ppm, average 52 ppm) basins. δ7Li of mudrocks from the northern Lake District (δ7Li =-3.2 ±1.6 permil, 2σ) are relatively constant compared to those of the mudrocks from the southern Lake District (-3.4 permil to 0 permil) and the Southern Uplands (-4.4 permil to +3.7 permil). Metamorphic grade, determined by the Kübler index method, does not correlate with [Li] or δ7Li, indicating that sub-greenschist facies metamorphism had little effect on Li in these mudrocks. Collectively, the data for all three basins show a negative correlation between [Li] and δ7Li and a positive correlation between [Li] and the chemical index of alteration (CIA), suggesting that provenance exerts the greatest control on Li in mudrocks. Samples from the northern Lake District, which were deposited in an extensional basin, have homogeneous REE patterns, similar to shale composites (PAAS and NASC), the highest CIA, Th/U and [Li] and the lowest δ7Li and ɛNd, consistent with their derivation from a highly weathered ancient continental source. By contrast, mudrocks from the Southern Uplands range to the lowest CIA, Th/U and [Li] and have the highest δ7Li and ɛNd. These samples were deposited in a subudction zone on the southern margin of the Laurentian craton and contain volcanic detritus derived from a proximal arc. They have the most variable REE patterns, ranging

NASA Goddards LiDAR, Hyperspectral and Thermal (G-LiHT) Airborne Imager

NASA Technical Reports Server (NTRS)

Cook, Bruce D.; Corp, Lawrence A.; Nelson, Ross F.; Middleton, Elizabeth M.; Morton, Douglas C.; McCorkel, Joel T.; Masek, Jeffrey G.; Ranson, Kenneth J.; Ly, Vuong; Montesano, Paul M.

2013-01-01

The combination of LiDAR and optical remotely sensed data provides unique information about ecosystem structure and function. Here, we describe the development, validation and application of a new airborne system that integrates commercial off the shelf LiDAR hyperspectral and thermal components in a compact, lightweight and portable system. Goddard's LiDAR, Hyperspectral and Thermal (G-LiHT) airborne imager is a unique system that permits simultaneous measurements of vegetation structure, foliar spectra and surface temperatures at very high spatial resolution (approximately 1 m) on a wide range of airborne platforms. The complementary nature of LiDAR, optical and thermal data provide an analytical framework for the development of new algorithms to map plant species composition, plant functional types, biodiversity, biomass and carbon stocks, and plant growth. In addition, G-LiHT data enhance our ability to validate data from existing satellite missions and support NASA Earth Science research. G-LiHT's data processing and distribution system is designed to give scientists open access to both low- and high-level data products (http://gliht.gsfc.nasa.gov), which will stimulate the community development of synergistic data fusion algorithms. G-LiHT has been used to collect more than 6,500 km2 of data for NASA-sponsored studies across a broad range of ecoregions in the USA and Mexico. In this paper, we document G-LiHT design considerations, physical specifications, instrument performance and calibration and acquisition parameters. In addition, we describe the data processing system and higher-level data products that are freely distributed under NASA's Data and Information policy.

Feasibility tests of nickel as a containment material of molten Li2O-LiCl salt containing Li metal at 650 °C during electrolytic reduction

NASA Astrophysics Data System (ADS)

Choi, Eun-Young; Lee, Jeong

2017-11-01

In this study, we investigated the feasibility of nickel (Ni) as a material to contain molten Li2O-LiCl salt containing lithium (Li) metal at 650 °C as an electrolyte during the electrolytic reduction process of pyroprocessing (also known as oxide reduction, OR). First, the behaviors of Ni in four different LiCl salts (0.1 wt% Li-LiCl, 1 and 8 wt% Li2O-LiCl, and 8 wt% Li2O-0.1 wt% Li-LiCl) in an argon atmosphere were examined through immersion tests. Then, Ni was used as a vessel material for five consecutive OR runs of simulated oxide fuel using 1.0 wt% Li2O-LiCl salt. The tested Ni was analyzed by microbalance, X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Concentrations of Ni in the salt were measured using inductively coupled plasma atomic emission spectroscopy. No corrosion product of Ni, except Cr2Ni3, was observed on the Ni used for both the salt-immersion tests and the OR runs because the Ni was not exposed to oxygen gas. However, leaching of Ni in the OR salt containing excessive Li metal was observed. Therefore, Ni can be used as the salt containment material in the OR process when excessive Li metal and oxygen gas in the salt are maintained at low levels.

[Clinical and experimental research on chronic bronchitis treated with ke chuan ping decoction].

PubMed

Cheng, C L

1991-04-01

This paper presents the results of clinical observation and experimental research of ke chuan ping (KCP) in treating 31 cases of chronic bronchitis compared with that of traditional prescription qing jin hua tan decoction (QJHT) in other 31 patients with the same conditions randomized as control. The total effective rate of KCP group was 93.55% including 67.74% of basically cured and markedly effective cases. The total effective rate of QJHT group was 74.19% including 41.94% basically cured and markedly effective cases. There were significant differences between them (P less than 0.05). According to laboratory observation KCP had the ability to dilute sputum viscosity, promote pulmonary ventilation function, decrease WBC and raise PO2. Animal experimental research suggested that KCP had the effects on reducing sputum, relieving cough, modifying stridor and inhibiting bacteria. It was proved that KCP is a highly effective recipe for patients with chronic bronchitis. It was also shown that clearing away heat and dispersing phlegm therapy is an important measure for chronic bronchitis with Biao Zheng.

An Ultrahigh Capacity Graphite/Li 2S Battery with Holey-Li 2S Nanoarchitectures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Fangmin; Noh, Hyungjun; Lee, Hongkyung

The pairing of high-capacity Li 2S cathode (1166 mAh g -1) and lithium-free anode (LFA) provides an unparalleled potential in developing safe and energy-dense next-generation secondary batteries. However, the low utilization of the Li 2S cathode and the lack of electrolytes compatible to both electrodes are impeding the development. Here, a novel graphite/Li 2S battery system, which features a self-assembled, holey-Li 2S nanoarchitecture and a stable solid electrolyte interface (SEI) on the graphite electrode, is reported. The holey structure on Li 2S is beneficial in decomposing Li 2S at the first charging process due to the enhanced Li ion extractionmore » and transfer from the Li 2S to the electrolyte. In addition, the concentrated dioxolane (DOL)-rich electrolyte designed lowers the irreversible capacity loss for SEI formation. By using the combined strategies, the graphite/holey-Li 2S battery delivers an ultrahigh discharge capacity of 810 mAh g -1 at 0.1 C (based on the mass of Li 2S) and of 714 mAh g -1 at 0.2 C. Moreover, it exhibits a reversible capacity of 300 mAh g -1 after a record lifecycle of 600 cycles at 1 C. These results suggest the great potential of the designed LFA/holey-Li 2S batteries for practical use.« less

An Ultrahigh Capacity Graphite/Li 2S Battery with Holey-Li 2S Nanoarchitectures

DOE PAGES

Ye, Fangmin; Noh, Hyungjun; Lee, Hongkyung; ...

2018-05-07

The pairing of high-capacity Li 2S cathode (1166 mAh g -1) and lithium-free anode (LFA) provides an unparalleled potential in developing safe and energy-dense next-generation secondary batteries. However, the low utilization of the Li 2S cathode and the lack of electrolytes compatible to both electrodes are impeding the development. Here, a novel graphite/Li 2S battery system, which features a self-assembled, holey-Li 2S nanoarchitecture and a stable solid electrolyte interface (SEI) on the graphite electrode, is reported. The holey structure on Li 2S is beneficial in decomposing Li 2S at the first charging process due to the enhanced Li ion extractionmore » and transfer from the Li 2S to the electrolyte. In addition, the concentrated dioxolane (DOL)-rich electrolyte designed lowers the irreversible capacity loss for SEI formation. By using the combined strategies, the graphite/holey-Li 2S battery delivers an ultrahigh discharge capacity of 810 mAh g -1 at 0.1 C (based on the mass of Li 2S) and of 714 mAh g -1 at 0.2 C. Moreover, it exhibits a reversible capacity of 300 mAh g -1 after a record lifecycle of 600 cycles at 1 C. These results suggest the great potential of the designed LFA/holey-Li 2S batteries for practical use.« less

Electronic structures of filled tetrahedral semiconductors LiMgN and LiZnN: conduction band distortion

NASA Astrophysics Data System (ADS)

Yu, L. H.; Yao, K. L.; Liu, Z. L.

2004-12-01

The band structures of the filled tetrahedral semiconductors LiMgN and LiZnN, viewed as the zinc-blende (MgN) - and (ZnN) - lattices partially filled with He-like Li + ion interstitials, were studied using the full-potential linearized augmented plane wave method (FP-LAPW) within density functional theory. The conduction band distortions of LiMgN and LiZnN, compared to their “parent” zinc-blende analog AlN and GaN, are discussed. It was found that the insertion of Li + ions at the interstitial sites near the cation or anion pushes the conduction band minimum of the X point in the Brillouin zone upward, relative to that of the Γ point, for both (MgN) - and (ZnN) - lattices (the valence band maximum is at Γ for AlN, GaN, LiMgN, and LiZnN), which provides a method to convert a zinc-blende indirect gap semiconductor into a direct gap material, but the conduction band distortion of the β phase (Li + near the cation) is quite stronger than that of the α phase (Li + near the anion). The total energy calculations show the α phase to be more stable than the β phase for both LiMgN and LiZnN. The Li-N and Mg-N bonds exhibit a strong ionic character, whereas the Zn-N bond has a strong covalent character in LiMgN and LiZnN.

LiGa(OTf)(sub 4) as an Electrolyte Salt for Li-Ion Cells

NASA Technical Reports Server (NTRS)

Reddy, V. Prakash; Prakash, G. K. Syria; Hu, Jinbo; Yan, Ping; Smart, Marshall; Bugga, ratnakumar; Chin, Keith; Surampudi, Subarao

2008-01-01

Lithium tetrakis(trifluoromethane sulfo - nato)gallate [abbreviated "LiGa(OTf)4" (wherein "OTf" signifies trifluoro - methanesulfonate)] has been found to be promising as an electrolyte salt for incorporation into both liquid and polymer electrolytes in both rechargeable and non-rechargeable lithium-ion electrochemical cells. This and other ingredients have been investigated in continuing research oriented toward im proving the performances of rechargeable lithium-ion electrochemical cells, especially at low temperatures. This research at earlier stages, and the underlying physical and chemical principles, were reported in numerous previous NASA Tech Briefs articles. As described in more detail in those articles, lithiumion cells most commonly contain nonaqueous electrolyte solutions consisting of lithium hexafluorophosphate (LiPF6) dissolved in mixtures of cyclic and linear alkyl carbonates, including ethylene carbonate (EC), propylene carbonate (PC), dimethyl carbonate (DMC), diethyl carbonate (DEC), and ethyl methyl carbonate (EMC). Although such LiPF6-based electrolyte solutions are generally highly ionically conductive and electrochemically stable, as needed for good cell performance, there is interest in identifying alternate lithium electrolyte salts that, relative to LiPF6, are more resilient at high temperature and are less expensive. Experiments have been performed on LiGa(OTf)4 as well as on several other candidate lithium salts in pursuit of this interest. As part of these experiments, LiGa(OTf)4 was synthesized by the reaction of Ga(OTf)3 with an equimolar portion of LiOTf in a solvent consisting of anhydrous acetonitrile. Evaporation of the solvent yielded LiGa(OTf)4 as a colorless crystalline solid. The LiGa(OTf)4 and the other salts were incorporated into solutions with PC and DMC. The resulting electrolyte solutions exhibited reasonably high ionic conductivities over a relatively wide temperature range down to 40 C (see figure). In cyclic

Line Lists for LiF and LiCl in the X 1Σ+ Ground State

NASA Astrophysics Data System (ADS)

Bittner, Dror M.; Bernath, Peter F.

2018-03-01

Vibration–rotation line lists for 6LiF, 7LiF, 6Li35Cl, 6Li37Cl, 7Li35Cl, and 7Li37Cl in the X 1Σ+ ground states have been prepared. The rovibrational energy levels have been calculated using potential energy surfaces determined by direct potential-fitting employing the rotational and rovibrational transition frequencies of all isotopologues, and required the inclusion of Born–Oppenheimer breakdown terms. Dipole moment functions calculated ab initio at the MRCI/aug-cc-pwCV5Z level have been used for line strength calculations. Partition functions for temperatures up to 5000 K have been calculated. LiF and LiCl are predicted to be present in the atmospheres of hot rocky exoplanets, brown dwarfs, and cool stars.

Electrochemical behavior of LiV3O8 positive electrode in hybrid Li,Na-ion batteries

NASA Astrophysics Data System (ADS)

Maletti, S.; Sarapulova, A.; Tsirlin, A. A.; Oswald, S.; Fauth, F.; Giebeler, L.; Bramnik, N. N.; Ehrenberg, H.; Mikhailova, D.

2018-01-01

Vanadium(V)-containing oxides show superior intercalation properties for alkaline ions, although the performance of the material strongly depends on its surface morphology. In this work, intercalation activity of LiV3O8, prepared by a conventional solid state synthesis, is demonstrated for the first time in non-aqueous Li,Na-ion hybrid batteries with Na as negative electrode, and different Na/Li ratios in the electrolyte. In the pure Na-ion cell, one Na per formula unit of LiV3O8 can be reversibly inserted at room temperature via a two-step process, while further intercalation leads to gradual amorphisation of the material, with a specific capacity of 190 mAhg-1 after 10 cycles in the potential window of 0.8-3.4 V. Hybrid Li,Na-ion batteries feature simultaneous intercalation of Li+ and Na+ cations into LiV3O8, resulting in the formation of a second phase. Depending on the electrolyte composition, this second phase bears structural similarities either to Li0.7Na0.7V3O8 in Na-rich electrolytes, or to Li4V3O8 in Li-rich electrolytes. The chemical diffusion coefficients of Na+ and Li+ in crystalline LiV3O8 are very close, hence explaining the co-intercalation of these cations. As DFT calculations show, once formed, the Li0.7Na0.7V3O8-type structure favors intercalation of Na+, whereas the LiV3O8-type prefers to accommodate Li+ cations.

Li interactions with the B40 fullerene and its application in Li-ion batteries: DFT studies

NASA Astrophysics Data System (ADS)

Moradi, Morteza; Bagheri, Zargham; Bodaghi, Ali

2017-05-01

The interaction of Li and Li+ with a B40 all-boron fullerene was theoretically investigated at the B3LYP, and Minnesota 2006 levels of theory. It was found that, unexpectedly, the interaction Li+ cation with the electron deficient B40 fullerene is stronger than the Li atom. It indicates that the B40 fullerene does not act as a conventional Lewis acid because of its highly correlated structure. Frontier molecular orbitals, partial density of states, and natural bond orbital analyses were used to discuss this unusual behavior. Our calculations indicate that this behavior makes the B40 fullerene more appropriate for application in the Li-ion batteries as anode material. The calculated cell voltage is about 530 mV. Also, it was found that Hartree Fock (HF) exchange percentage of density functionals has a reverse effect on the adsorption energies of Li and Li+. This energy is increased and decreased, respectively, for Li+ and Li adsorptions by increasing %HF exchange. Finally, a potential energy surface for Li and Li+ penetration into B40 fullerene was predicted.

Association and Diffusion of Li(+) in Carboxymethylcellulose Solutions for Environmentally Friendly Li-ion Batteries.

PubMed

Casalegno, Mosè; Castiglione, Franca; Passarello, Marco; Mele, Andrea; Passerini, Stefano; Raos, Guido

2016-07-21

Carboxymethylcellulose (CMC) has been proposed as a polymeric binder for electrodes in environmentally friendly Li-ion batteries. Its physical properties and interaction with Li(+) ions in water are interesting not only from the point of view of electrode preparation-processability in water is one of the main reasons for its environmental friendliness-but also for its possible application in aqueous Li-ion batteries. We combine molecular dynamics simulations and variable-time pulsed field gradient spin-echo (PFGSE) NMR spectroscopy to investigate Li(+) transport in CMC-based solutions. Both the simulations and experimental results show that, at concentrations at which Li-CMC has a gel-like consistency, the Li(+) diffusion coefficient is still very close to that in water. These Li(+) ions interact preferentially with the carboxylate groups of CMC, giving rise to a rich variety of coordination patterns. However, the diffusion of Li(+) in these systems is essentially unrestricted, with a fast, nanosecond-scale exchange of the ions between CMC and the aqueous environment. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reversible Li storage for nanosize cation/anion-disordered rocksalt-type oxyfluorides: LiMoO2 - x LiF (0 ≤ x ≤ 2) binary system

NASA Astrophysics Data System (ADS)

Takeda, Nanami; Hoshino, Satoshi; Xie, Lixin; Chen, Shuo; Ikeuchi, Issei; Natsui, Ryuichi; Nakura, Kensuke; Yabuuchi, Naoaki

2017-11-01

A binary system of LiMoO2 - x LiF (0 ≤ x ≤ 2), Li1+xMoO2Fx, is systematically studied as potential positive electrode materials for rechargeable Li batteries. Single phase and nanosized samples on this binary system are successfully prepared by using a mechanical milling route. Crystal structures and Li storage properties on the binary system are also examined. Li2MoO2F (x = 1), which is classified as a cation-/anion-disordered rocksalt-type structure and is a thermodynamically metastable phase, delivers a large reversible capacity of over 300 mAh g-1 in Li cells with good reversibility. Highly reversible Li storage is realized for Li2MoO2F consisting of nanosized particles based on Mo3+/Mo5+ two-electron redox as evidenced by ex-situ X-ray absorption spectroscopy coupled with ex-situ X-ray diffractometry. Moreover, the presence of the most electronegative element in the framework structure effectively increases the electrode potential of Mo redox through an inductive effect. From these results, potential of nanosized lithium molybdenum oxyfluorides for high-capacity positive electrode materials of rechargeable Li batteries are discussed.

The Impact of Modernization on the Military Capabilities of the People’s Republic of China.

DTIC Science & Technology

1982-04-19

pair of allies on the Standing Committee were Ye Jianying and Li Xiannian, who represented both the veteran cadres who had survived the Cultural...in October with the arrest of the four leading radical figures ("Gang of Four") in a coup lead by the Defense Minister, Marshall Ye Jianying who...Dengkui, and Wu De, from the Politburo. A new Standing Committee was constituted on which Hua Guofeng now sat in lonely isolation; Marshal Ye Jianying and

Photoionization of Li2

NASA Astrophysics Data System (ADS)

Li, Y.; Pindzola, M. S.; Ballance, C. P.; Colgan, J.

2014-05-01

Single and double photoionization cross sections for Li2 are calculated using a time-dependent close-coupling method. The correlation between the outer two electrons of Li2 is obtained by relaxation of the close-coupled equations in imaginary time. Propagation of the close-coupled equations in real time yields single and double photoionization cross sections for Li2. The two active electron cross sections are compared with one active electron distorted-wave and close-coupling results for both Li and Li2. This work was supported in part by grants from NSF and US DoE. Computational work was carried out at NERSC in Oakland, California, NICS in Knoxville, Tennessee, and OLCF in Oak Ridge, Tennessee.

Complex Diffusion Mechanisms for Li in Feldspar: Re-thinking Li-in-Plag Geospeedometry

NASA Astrophysics Data System (ADS)

Holycross, M.; Watson, E. B.

2017-12-01

In recent years, the lithium isotope system has been applied to model processes in a wide variety of terrestrial environments. In igneous settings, Li diffusion gradients have been frequently used to time heating episodes. Lithium partitioning behavior during decompression or cooling events drives Li transfer between phases, but the extent of Li exchange may be limited by its diffusion rate in geologic materials. Lithium is an exceptionally fast diffuser in silicate media, making it uniquely suited to record short-lived volcanic phenomena. The Li-in-plagioclase geospeedometer is often used to time explosive eruptions by applying laboratory-calibrated Li diffusion coefficients to model concentration profiles in magmatic feldspar samples. To quantify Li transport in natural scenarios, experimental measurements are needed that account for changing temperature and oxygen fugacity as well as different feldspar compositions and crystallographic orientation. Ambient pressure experiments were run at RPI to diffuse Li from a powdered spodumene source into polished sanidine, albite, oligoclase or anorthite crystals over the temperature range 500-950 ºC. The resulting 7Li concentration gradients developed in the mineral specimens were evaluated using laser ablation ICP-MS. The new data show that Li diffusion in all feldspar compositions simultaneously operates by both a "fast" and "slow" diffusion mechanism. Fast path diffusivities are similar to those found by Giletti and Shanahan [1997] for Li diffusion in plagioclase and are typically 10 to 20 times greater than slow path diffusivities. Lithium concentration gradients in the feldspar experiments plot in the shape of two superimposed error function curves with the slow diffusion regime in the near-surface of the crystal. Lithium diffusion is most sluggish in sanidine and is significantly faster in the plagioclase feldspars. It is still unclear what diffusion mechanism operates in nature, but the new measurements may impact

Low-lying electronic states of Li 2+ and Li 2-

NASA Astrophysics Data System (ADS)

Konowalow, Daniel D.; Fish, James L.

1984-02-01

Potential curves for the eight lowest lying electronic states of Li2+ and the two lowest-lying states of Li2- are obtained by valence configuration calculations which-utilize an effective core potential. The calculated ionization potential of the ground state of Li2 is found to b. 5.16 eV and its electron affinity is 0.429 eV. Both values are in excellent agreement with recent experimental values and with value deduced from other high quality ab initio quantum mechanical treatments. When our potential curve for the Li2+(12Σg+ state, is corrected for the core-valence correlation error we obtain spectroscopic constants which agree nicely with the experimental values of Bernheim, Gold and Tipton (BGT). For example, we findDe = 10460 ± 140 cm-1 while BGT reportDe = 10469 ± 6 cm-1.

Preparation and some properties of Cu-Li alloys containing up to 20 at. % Li

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendelsohn, M.; Krauss, A.R.; Gruen, D.M.

1985-01-01

Lithium strongly segregates to the surface of Cu-Li alloys, thus substantially lowering the Cu sputtering yield relative to pure Cu. Use of Cu-Li limiters or divertors in tokamaks can therefore be expected to be beneficial in limiting high-Z plasma impurity influx. A large scale (100-200g) method for the preparation of Cu-Li alloys is described. Analysis reveals that on solidification from the melt stratification occurs which leads to compositional inhomogeneity. The results are discussed in the light of the Cu-Li binary phase diagram and rationalized on the basis of large density differences between Cu and Cu-Li solid solutions. It is concludedmore » that obtaining homogeneous Cu-Li solid solutions is a nontrivial task.« less

An Integrative Platform of TCM Network Pharmacology and Its Application on a Herbal Formula, Qing-Luo-Yin

PubMed Central

Zhang, Bo; Wang, Xu; Li, Shao

2013-01-01

The scientific understanding of traditional Chinese medicine (TCM) has been hindered by the lack of methods that can explore the complex nature and combinatorial rules of herbal formulae. On the assumption that herbal ingredients mainly target a molecular network to adjust the imbalance of human body, here we present a-self-developed TCM network pharmacology platform for discovering herbal formulae in a systematic manner. This platform integrates a set of network-based methods that we established previously to catch the network regulation mechanism and to identify active ingredients as well as synergistic combinations for a given herbal formula. We then provided a case study on an antirheumatoid arthritis (RA) formula, Qing-Luo-Yin (QLY), to demonstrate the usability of the platform. We revealed the target network of QLY against RA-related key processes including angiogenesis, inflammatory response, and immune response, based on which we not only predicted active and synergistic ingredients from QLY but also interpreted the combinatorial rule of this formula. These findings are either verified by the literature evidence or have the potential to guide further experiments. Therefore, such a network pharmacology strategy and platform is expected to make the systematical study of herbal formulae achievable and to make the TCM drug discovery predictable. PMID:23653662

Observation of Li Diffusion in Cathode Sheets of Li-ion Battery by μ+SR

NASA Astrophysics Data System (ADS)

Umegaki, Izumi; Kawauchi, Shigehiro; Nozaki, Hiroshi; Sawada, Hiroshi; Nakano, Hiroyuki; Harada, Masashi; Cottrell, Stephen P.; Coomer, Fiona C.; Telling, Mark; Sugiyama, Jun

In order to know the change in Li diffusion during the operation of Li-ion batteries, we have initiated to measure Li diffusion not only in a powder sample but also in a cathode sheet with μ+SR. As the first step, we have measured μ+SR spectra on a cathode sheet, in which a mixture of a cathode material Li(Ni, Co)O2, a binder, and conducting additives is coated on an Al foil. The zero-field μ+SR spectrum exhibited a typical Kubo-Toyabe (KT) type relaxation at 100 K. By subtracting the contribution of the muons stopped in the Al foil, we found that Li+ ion starts to diffuse above 100 K in the Li(Ni, Co)O2. A self diffusion coefficient (DLi) at 300 K was estimated as 10-11 (cm2/s), which comparable with DLi (300 K) in the cathode materials previously reported. This leads to the future "in operando" measurements of DLi in Li-ion batteries.

Electrochemical behaviors of wax-coated Li powder/Li 4Ti 5O 12 cells

NASA Astrophysics Data System (ADS)

Park, Han Eol; Seong, Il Won; Yoon, Woo Young

The wax-coated Li powder specimen was effectively synthesized using the drop emulsion technique (DET). The wax layer on the powder was verified by SEM, Focused Ion Beam (FIB), EDX and XPS. The porosity of a sintered wax-coated Li electrode was measured by linear sweep voltammetry (LSV) and compared with that of a bare, i.e., un-coated Li electrode. The electrochemical behavior of the wax-coated Li powder anode cell was examined by the impedance analysis and cyclic testing methods. The cyclic behavior of the wax-coated Li powder anode with the Li 4Ti 5O 12 (LTO) cathode cell was examined at a constant current density of 0.35 mA cm -2 with the cut-off voltages of 1.2-2.0 V at 25 °C. Over 90% of the initial capacity of the cell remained even after the 300th cycle. The wax-coated Li powder was confirmed to be a stable anode material.

Comparative study of imide-based Li salts as electrolyte additives for Li-ion batteries

NASA Astrophysics Data System (ADS)

Sharova, Varvara; Moretti, Arianna; Diemant, Thomas; Varzi, Alberto; Behm, R. Jürgen; Passerini, Stefano

2018-01-01

Herein, we report the results of a detailed study on the use of different Li imide salts (LiTFSI, LiFSI, and LiFTFSI) as electrolyte additives for lithium-ion batteries. The introduction of lithium imide salts in the electrolyte is shown to considerably improve the first cycle coulombic efficiency and the long-term cycling stability of graphite/LiFePO4 cells. Using LiTFSI, a capacity fading of only ∼2% occurred over 600 cycles while the control cell with the state-of-the-art additive (VC) lost ∼20% of the initial capacity at 20 °C. The results of the XPS and impedance spectroscopy measurements of graphite electrodes show that, after the formation cycle, the SEI obtained in the presence of imide salts is thinner, contains more LiF and is less resistive than that obtained using VC. Despite the beneficial effect of the imide salts on the lithium-ion cell performance, a slightly reduced thermal stability of the SEI is observed.

LiCl-LiI molten salt electrolyte with bismuth-lead positive electrode for liquid metal battery

NASA Astrophysics Data System (ADS)

Kim, Junsoo; Shin, Donghyeok; Jung, Youngjae; Hwang, Soo Min; Song, Taeseup; Kim, Youngsik; Paik, Ungyu

2018-02-01

Liquid metal batteries (LMBs) are attractive energy storage device for large-scale energy storage system (ESS) due to the simple cell configuration and their high rate capability. The high operation temperature caused by high melting temperature of both the molten salt electrolyte and metal electrodes can induce the critical issues related to the maintenance cost and degradation of electrochemical properties resulting from the thermal corrosion of materials. Here, we report a new chemistry of LiCl-LiI electrolyte and Bi-Pb positive electrode to lower the operation temperature of Li-based LMBs and achieve the long-term stability. The cell (Li|LiCl-LiI|Bi-Pb) is operated at 410 °C by employing the LiCl-LiI (LiCl:LiI = 36:64 mol %) electrolyte and Bi-Pb alloy (Bi:Pb = 55.5:44.5 mol %) positive electrode. The cell shows excellent capacity retention (86.5%) and high Coulombic efficiencies over 99.3% at a high current density of 52 mA cm-2 during 1000th cycles.

Configuring PSx tetrahedral clusters in Li-excess Li7P3S11 solid electrolyte

NASA Astrophysics Data System (ADS)

Jung, Wo Dum; Yun, Bin-Na; Jung, Hun-Gi; Choi, Sungjun; Son, Ji-Won; Lee, Jong-Ho; Lee, Jong-Heun; Kim, Hyoungchul

2018-04-01

We demonstrate that the Li-ion conductivity can be improved by adding a certain amount of Li (x = 0.25-0.5) as a charge carrier to the composition of glass-ceramic Li7+xP3S11. Structural analysis clarified that the structural changes caused by the ratio of ortho-thiophosphate tetrahedra PS43- and pyro-thiophosphate ditetrahedra P2S74- affect the Li-ion conductivity. The ratio of PS43- and P2S74- varies depending on x and the highest Li-ion conductivity (2.5 × 10-3 S cm-1) at x = 0.25. All-solid-state LiNi0.8Co0.15Al0.05O2/Li7.25P3S11/In-metal cell exhibits the discharge capacity of 106.2 mAh g-1. This ion conduction enhancement from excess Li is expected to contribute to the future design of sulfide-type electrolytes.

Li diffusion and the effect of local structure on Li mobility in Li2O-SiO2 glasses.

PubMed

Bauer, Ute; Welsch, Anna-Maria; Behrens, Harald; Rahn, Johanna; Schmidt, Harald; Horn, Ingo

2013-12-05

Aimed to improve the understanding of lithium migration mechanisms in ion conductors, this study focuses on Li dynamics in binary Li silicate glasses. Isotope exchange experiments and conductivity measurements were carried out to determine self-diffusion coefficients and activation energies for Li migration in Li2Si3O7 and Li2Si6O13 glasses. Samples of identical composition but different isotope content were combined for diffusion experiments in couples or triples. Diffusion profiles developed between 511 and 664 K were analyzed by femtosecond laser ablation combined with multiple collector inductively coupled plasma mass spectrometry (fs LA-MC-ICP-MS) and secondary ion mass spectrometry (SIMS). Analyses of diffusion profiles and comparison of diffusion data reveal that the isotope effect of lithium diffusion in silicate glasses is rather small, consistent with classical diffusion behavior. Ionic conductivity of glasses was measured between 312 and 675 K. The experimentally obtained self-diffusion coefficient, D(IE), and ionic diffusion coefficient, D(σ), derived from specific DC conductivity provided information about correlation effects during Li diffusion. The D(IE)/D(σ) is higher for the trisilicate (0.27 ± 0.05) than that for the hexasilicate (0.17 ± 0.02), implying that increasing silica content reduces the efficiency of Li jumps in terms of long-range movement. This trend can be rationalized by structural concepts based on nuclear magnetic resonance (NMR) and Raman spectroscopy as well as molecular dynamic simulations, that is, lithium is percolating in low-dimensional, alkali-rich regions separated by a silica-rich matrix.

Effects of substitutional Li on the ferromagnetic response of Li co-doped ZnO:Co nanoparticles.

PubMed

Awan, Saif Ullah; Hasanain, S K; Bertino, Massimo F; Jaffari, G Hassnain

2013-04-17

Li co-doped ZnO:Co (Zn0.96-yCo0.04LiyO , y ≤ 0.1) nanoparticles were synthesized by the sol-gel technique and the correlation between the structural, electronic and magnetic properties was investigated. All the samples show a single phase hexagonal (wurtzite) ZnO structure and no secondary phases were detected. Variational trends in lattice parameters suggest the incorporation of Li in the ZnO:Co system in both substitutional and interstitial sites. Detailed electronic studies have been performed by high-resolution x-ray photoelectron spectroscopy (XPS) to determine the states of Zn, O, Co and Li. It was determined that Co substitutes at Zn sites (CoZn) while the O vacancy and Zn defects did not show much variation with increasing Li concentration. Deconvolution of the Li XPS peak showed a clear non-monotonic trend in the variation of the substitutional Li (LiZn) and interstitial Li (Lii) defects with increasing Li concentration in the particles. The magnetization study of the samples showed that the variation of the moment closely followed the trend of variation of the LiZn defects. The data are interpreted in terms of substitutional Li acting as a hole dopant and optimizing the conditions for ferromagnetism in Co-doped ZnO. Interstitial Li is not seen to be playing this role.

Reversible superconductor-insulator transition in LiTi2O4 induced by Li-ion electrochemical reaction

PubMed Central

Yoshimatsu, K.; Niwa, M.; Mashiko, H.; Oshima, T.; Ohtomo, A.

2015-01-01

Transition metal oxides display various electronic and magnetic phases such as high-temperature superconductivity. Controlling such exotic properties by applying an external field is one of the biggest continuous challenges in condensed matter physics. Here, we demonstrate clear superconductor-insulator transition of LiTi2O4 films induced by Li-ion electrochemical reaction. A compact electrochemical cell of pseudo-Li-ion battery structure is formed with a superconducting LiTi2O4 film as an anode. Li content in the film is controlled by applying a constant redox voltage. An insulating state is achieved by Li-ion intercalation to the superconducting film by applying reduction potential. In contrast, the superconducting state is reproduced by applying oxidation potential to the Li-ion intercalated film. Moreover, superconducting transition temperature is also recovered after a number of cycles of Li-ion electrochemical reactions. This complete reversible transition originates in difference in potentials required for deintercalation of initially contained and electrochemically intercalated Li+ ions. PMID:26541508

Reversible superconductor-insulator transition in LiTi2O4 induced by Li-ion electrochemical reaction.

PubMed

Yoshimatsu, K; Niwa, M; Mashiko, H; Oshima, T; Ohtomo, A

2015-11-06

Transition metal oxides display various electronic and magnetic phases such as high-temperature superconductivity. Controlling such exotic properties by applying an external field is one of the biggest continuous challenges in condensed matter physics. Here, we demonstrate clear superconductor-insulator transition of LiTi2O4 films induced by Li-ion electrochemical reaction. A compact electrochemical cell of pseudo-Li-ion battery structure is formed with a superconducting LiTi2O4 film as an anode. Li content in the film is controlled by applying a constant redox voltage. An insulating state is achieved by Li-ion intercalation to the superconducting film by applying reduction potential. In contrast, the superconducting state is reproduced by applying oxidation potential to the Li-ion intercalated film. Moreover, superconducting transition temperature is also recovered after a number of cycles of Li-ion electrochemical reactions. This complete reversible transition originates in difference in potentials required for deintercalation of initially contained and electrochemically intercalated Li(+) ions.

[Comprehension and explanation of meridians and collaterals theory in the background of the spread of western medicine into the East in the Ming and Qing Dynasties].

PubMed

Li, Su-Yun

2010-06-01

In the background of the spread of western medicine into the East in the Ming and Qing Dynasties, Chinese doctors who had accepted western medicine referred to western medical knowledge and began to use the methods of anatomical observation and demonstrating to explain the objective structure of meridians and collaterals. They tried to adopt the artery and vessel explaining the shape of meridian and the blood circle and pulmonary respiration explaining the circulation of Ying-Wei. When the anatomy structures could not perfectly equal to meridians and collaterals, some doctors put forward the gasification feature of meridian to explain the reason. These results suggest that there are difference between meridians and collaterals and pure anatomy concepts, which serves as significant reference and edification for later generations.

Formation and reduction behaviors of zirconium oxide compounds in LiCl-Li2O melt at 923 K

NASA Astrophysics Data System (ADS)

Sakamura, Yoshiharu; Iizuka, Masatoshi; Kitawaki, Shinichi; Nakayoshi, Akira; Kofuji, Hirohide

2015-11-01

The reduction behaviors of ZrO2, Li2ZrO3 and (U,Pu,Zr)O2 in a LiCl-Li2O salt bath at 923 K were investigated. This study was conducted as part of a feasibility study on the pyrochemical treatment of damaged fuel debris generated by severe accidents at light water reactors. It was demonstrated in electrolytic reduction tests that the uranium in synthetic corium specimens of (U,Pu,Zr)O2 with various ZrO2 contents could be reduced to the metallic form and that part of the zirconium was converted to Li2ZrO3. Zirconium metal and Li2ZrO3 were obtained by the reduction of ZrO2. The reduction of Li2ZrO3 did not proceed even in LiCl containing no Li2O. Moreover, the stable chemical forms of the ZrO2-Li2O complex oxide were investigated as a function of the Li2O concentration in LiCl. ZrO2 was converted to Li2ZrO3 at a Li2O concentration of 0.018 wt%. As the Li2O concentration was increased, Li2ZrO3 was converted to Li6Zr2O7 and then to Li8ZrO6. It is suggested that the removal of Li2ZrO3 from the reduction product is a key point in the pyrochemical treatment of corium.

Presence of Li Clusters in Molten LiCl-Li

PubMed Central

Merwin, Augustus; Phillips, William C.; Williamson, Mark A.; Willit, James L.; Motsegood, Perry N.; Chidambaram, Dev

2016-01-01

Molten mixtures of lithium chloride and metallic lithium are of significant interest in various metal oxide reduction processes. These solutions have been reported to exhibit seemingly anomalous physical characteristics that lack a comprehensive explanation. In the current work, the physical chemistry of molten solutions of lithium chloride and metallic lithium, with and without lithium oxide, was investigated using in situ Raman spectroscopy. The Raman spectra obtained from these solutions were in agreement with the previously reported spectrum of the lithium cluster, Li8. This observation is indicative of a nanofluid type colloidal suspension of Li8 in a molten salt matrix. It is suggested that the formation and suspension of lithium clusters in lithium chloride is the cause of various phenomena exhibited by these solutions that were previously unexplainable. PMID:27145895

Presence of Li clusters in molten LiCl-Li

DOE PAGES

Merwin, Augustus; Phillips, William C.; Williamson, Mark A.; ...

2016-05-05

Molten mixtures of lithium chloride and metallic lithium are of significant interest in various metal oxide reduction processes. These solutions have been reported to exhibit seemingly anomalous physical characteristics that lack a comprehensive explanation. ln the current work, the physical chemistry of molten solutions of lithium chloride and metallic lithium, with and without lithium oxide, was investigated using in situ Raman spectroscopy. The Raman spectra obtained from these solutions were in agreement with the previously reported spectrum of the lithium cluster, Li 8. Furthermore, this observation is indicative of a nanofluid type colloidal suspension of Li 8, in a moltenmore » salt matrix. It is suggested that the formation and suspension of lithium clusters in lithium chloride is the cause of various phenomena exhibited by these solutions that were previously unexplainable.« less

Asymptotic and near-target direct breakup of 6Li and 7Li

NASA Astrophysics Data System (ADS)

Kalkal, Sunil; Simpson, E. C.; Luong, D. H.; Cook, K. J.; Dasgupta, M.; Hinde, D. J.; Carter, I. P.; Jeung, D. Y.; Mohanto, G.; Palshetkar, C. S.; Prasad, E.; Rafferty, D. C.; Simenel, C.; Vo-Phuoc, K.; Williams, E.; Gasques, L. R.; Gomes, P. R. S.; Linares, R.

2016-04-01

Background: Li,76 and 9Be are weakly bound against breakup into their cluster constituents. Breakup location is important for determining the role of breakup in above-barrier complete fusion suppression. Recent works have pointed out that experimental observables can be used to separate near-target and asymptotic breakup. Purpose: Our purpose is to distinguish near-target and asymptotic direct breakup of Li,76 in reactions with nuclei in different mass regions. Method: Charged particle coincidence measurements are carried out with pulsed Li,76 beams on 58Ni and 64Zn targets at sub-barrier energies and compared with previous measurements using 208Pb and 209Bi targets. A detector array providing a large angular coverage is used, along with time-of-flight information to give definitive particle identification of the direct breakup fragments. Results: In interactions of 6Li with 58Ni and 64Zn, direct breakup occurs only asymptotically far away from the target. However, in interactions with 208Pb and 209Bi, near-target breakup occurs in addition to asymptotic breakup. Direct breakup of 7Li into α -t is not observed in interactions with 58Ni and 64Zn. However, near-target dominated direct breakup was observed in measurements with 208Pb and 209Bi. A modified version of the Monte Carlo classical trajectory model code platypus, which explicitly takes into account lifetimes associated with unbound states, is used to simulate sub-barrier breakup reactions. Conclusions: Near-target breakup in interactions with Li,76 is an important mechanism only for the heavy targets 208Pb and 209Bi. There is insignificant near-target direct breakup of 6Li and no direct breakup of 7Li in reactions with 58Ni and 64Zn. Therefore, direct breakup is unlikely to suppress the above-barrier fusion cross section in reactions of Li,76 with 58Ni and 64Zn nuclei.

Relaxation-Induced Memory Effect of LiFePO4 Electrodes in Li-Ion Batteries.

PubMed

Jia, Jianfeng; Tan, Chuhao; Liu, Mengchuang; Li, De; Chen, Yong

2017-07-26

In Li-ion batteries, memory effect has been found in several commercial two-phase materials as a voltage bump and a step in the (dis)charging plateau, which delays the two-phase transition and influences the estimation of the state of charge. Although memory effect has been first discovered in olivine LiFePO 4 , the origination and dependence are still not clear and are critical for regulating the memory effect of LiFePO 4 . Herein, LiFePO 4 has been synthesized by a home-built spray drying instrument, of which the memory effect has been investigated in Li-ion batteries. For as-synthesized LiFePO 4 , the memory effect is significantly dependent on the relaxation time after phase transition. Besides, the voltage bump of memory effect is actually a delayed voltage overshooting that is overlaid at the edge of stepped (dis)charging plateau. Furthermore, we studied the kinetics of LiFePO 4 electrode with electrochemical impedance spectroscopy (EIS), which shows that the memory effect is related to the electrochemical kinetics. Thereby, the underlying mechanism has been revealed in memory effect, which would guide us to optimize two-phase electrode materials and improve Li-ion battery management systems.

A highly efficient Li2O2 oxidation system in Li-O2 batteries.

PubMed

Hase, Yoko; Seki, Juntaro; Shiga, Tohru; Mizuno, Fuminori; Nishikoori, Hidetaka; Iba, Hideki; Takechi, Kensuke

2016-10-06

A novel indirect charging system that uses a redox mediator was demonstrated for Li-O 2 batteries. 4-Methoxy-2,2,6,6-tetramethylpiperidinyl-1-oxyl (MeO-TEMPO) was applied as a mediator to enable the oxidation of Li 2 O 2 , even though Li 2 O 2 is electrochemically isolated. This system promotes the oxidation of Li 2 O 2 without parasitic reactions attributed to electrochemical charging and reduces the charging time.

Molecular evolution of the Li/li chemical defence polymorphism in white clover (Trifolium repens L.).

PubMed

Olsen, K M; Sutherland, B L; Small, L L

2007-10-01

White clover (Trifolium repens) is naturally polymorphic for cyanogenesis (hydrogen cyanide release following tissue damage). The ecological factors favouring cyanogenic and acyanogenic plants have been examined in numerous studies over the last half century, making this one of the best-documented examples of an adaptive polymorphism in plants. White clover cyanogenesis is controlled by two, independently segregating Mendelian genes: Ac/ac controls the presence/absence of cyanogenic glucosides; and Li/li controls the presence/absence of their hydrolysing enzyme, linamarase. In this study, we examine the molecular evolution and population genetics of Li as it relates to the cyanogenesis polymorphism. We report here that Li exists as a single-copy gene in plants possessing linamarase activity, and that the absence of enzyme activity in li/li plants is correlated with the absence of much or all of the gene from the white clover genome. Consistent with this finding, we confirm by reverse transcription-polymerase chain reaction that Li gene expression is absent in plants lacking enzyme activity. In a molecular population genetic analysis of Li and three unlinked genes using a worldwide sample of clover plants, we find an absence of nucleotide variation and statistically significant deviations from neutrality at Li; these findings are consistent with recent positive directional selection at this cyanogenesis locus.

Al-Cu-Li and Al-Mg-Li alloys: Phase composition, texture, and anisotropy of mechanical properties (Review)

NASA Astrophysics Data System (ADS)

Betsofen, S. Ya.; Antipov, V. V.; Knyazev, M. I.

2016-04-01

The results of studying the phase transformations, the texture formation, and the anisotropy of the mechanical properties in Al-Cu-Li and Al-Mg-Li alloys are generalized. A technique and equations are developed to calculate the amounts of the S1 (Al2MgLi), T1 (Al2CuLi), and δ' (Al3Li) phases. The fraction of the δ' phase in Al-Cu-Li alloys is shown to be significantly higher than in Al-Mg-Li alloys. Therefore, the role of the T1 phase in the hardening of Al-Cu-Li alloys is thought to be overestimated, especially in alloys with more than 1.5% Li. A new model is proposed to describe the hardening of Al-Cu-Li alloys upon aging, and the results obtained with this model agree well with the experimental data. A texture, which is analogous to that in aluminum alloys, is shown to form in sheets semiproducts made of Al-Cu-Li and Al-Mg-Li alloys. The more pronounced anisotropy of the properties of lithium-containing aluminum alloys is caused by a significant fraction of the ordered coherent δ' phase, the deformation mechanism in which differs radically from that in the solid solution.

Preparation of Ce- and La-Doped Li4Ti5O12 Nanosheets and Their Electrochemical Performance in Li Half Cell and Li4Ti5O12/LiFePO4 Full Cell Batteries

PubMed Central

Qin, Meng; Li, Yueming; Lv, Xiao-Jun

2017-01-01

This work reports on the synthesis of rare earth-doped Li4Ti5O12 nanosheets with high electrochemical performance as anode material both in Li half and Li4Ti5O12/LiFePO4 full cell batteries. Through the combination of decreasing the particle size and doping by rare earth atoms (Ce and La), Ce and La doped Li4Ti5O12 nanosheets show the excellent electrochemical performance in terms of high specific capacity, good cycling stability and excellent rate performance in half cells. Notably, the Ce-doped Li4Ti5O12 shows good electrochemical performance as anode in a full cell which LiFePO4 was used as cathode. The superior electrochemical performance can be attributed to doping as well as the nanosized particle, which facilitates transportation of the lithium ion and electron transportation. This research shows that the rare earth doped Li4Ti5O12 nanosheets can be suitable as a high rate performance anode material in lithium-ion batteries. PMID:28632167

Rate-dependent, Li-ion insertion/deinsertion behavior of LiFePO4 cathodes in commercial 18650 LiFePO4 cells.

PubMed

Liu, Qi; He, Hao; Li, Zhe-Fei; Liu, Yadong; Ren, Yang; Lu, Wenquan; Lu, Jun; Stach, Eric A; Xie, Jian

2014-03-12

We have performed operando synchrotron high-energy X-ray diffraction (XRD) to obtain nonintrusive, real-time monitoring of the dynamic chemical and structural changes in commercial 18650 LiFePO4/C cells under realistic cycling conditions. The results indicate a nonequilibrium lithium insertion and extraction in the LiFePO4 cathode, with neither the LiFePO4 phase nor the FePO4 phase maintaining a static composition during lithium insertion/extraction. On the basis of our observations, we propose that the LiFePO4 cathode simultaneously experiences both a two-phase reaction mechanism and a dual-phase solid-solution reaction mechanism over the entire range of the flat voltage plateau, with this dual-phase solid-solution behavior being strongly dependent on charge/discharge rates. The proposed dual-phase solid-solution mechanism may explain the remarkable rate capability of LiFePO4 in commercial cells.

Fine structures of the ejaculatory sac and sperm pump of the scorpionfly Panorpa liui Hua (Mecoptera: Panorpidae).

PubMed

Shen, Jian; Hua, Baozhen

2013-08-01

Male adults of Panorpidae possess a special sperm pump, through which the males transfer liquid sperm to the females. However, the structures of the sperm pump and the transfer mechanism have not been satisfactorily elucidated hitherto. In this paper the structures of the ejaculatory sac and sperm pump of the scorpionfly Panorpa liui Hua were investigated using light microscopy and scanning electron microscopy. The ejaculatory sac is located between the basal end of the paired vasa deferentia and the aedeagus, comprising a small anterior part and a large posterior part. The anterior part is simple and functions only as a channel for sperm transfer. The epithelial cells of the large posterior part likely have secretory functions. The sperm pump is formed by the posterior region of the ejaculatory sac and derivates of the genital field, which enclose the pumping chamber, a piston and the associated muscles. The orifice of the ejaculatory duct lies ventrad of the piston. The piston of the sperm pump is heavily sclerotized and controlled by two antagonistic muscle pairs. A pair of simple tubular accessory glands opens to the pumping chamber. Two well-developed sex pheromone glands are located on the ventral side of the ejaculatory sac, and are composed of two fan-shaped lamellae. The epithelium of the sex pheromone glands is single-layered, and forms densely filamentous processes. The ejaculation mechanism is briefly discussed based on the morphology of ejaculatory sac and sperm pump. Copyright © 2013 Elsevier Ltd. All rights reserved.

Direct synthesis and characterization of mixed-valent Li 0.5$-$δCoPO 4, a Li-deficient derivative of the Cmcm polymorph of LiCoPO 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ludwig, Jennifer; Alarcon-Suesca, Carlos; Geprags, Stephan

While the majority of research activities on LiCoPO 4 is focussed on the thermodynamically stable olivine-type Pnma polymorph, the metastable Pna2 1 and Cmcm modifications have recently attracted considerable attention due to their interesting material properties. In this study, we present the first Li-deficient structural derivative of the Cmcm modification with the nominal composition Li 0.5–δCoPO 4. As opposed to the substoichiometric olivine ( Pnma) phases Li xCoPO 4 (x = 0; 2/3), which are exclusively accessible by electrochemical or chemical Li extraction techniques, this is also the first time that a direct soft-chemical synthesis route towards a Li xCoPOmore » 4-type material is accomplished. X-ray and neutron diffraction studies indicate that Cmcm-type Li 0.5–δCoPO 4 shows vacancies on both the Li and Co sites, whereas X-ray absorption spectra demonstrate that the structure features heterovalent Co ions (+2/+3) to compensate for the Li deficit. Magnetic measurements reveal a long-range antiferromagnetic order below 10.5 K. A thorough investigation of the thermal stability using thermogravimetric analysis, differential scanning calorimetry, and temperature-dependent in situ X-ray powder diffraction demonstrates that Li 0.5–δCoPO 4 is metastable and exhibits a complex, multi-step thermal decomposition mechanism. In the first step at 394 °C, it decomposes to α-Co 2P 2O 7 ( P2 1/c) and LiCoPO 4 ( Cmcm) upon O 2 release. The LiCoPO 4 ( Cmcm) intermediate is then irreversibly transformed to olivine-type LiCoPO 4 (Pnma) at 686 °C. Furthermore, the material properties of Li 0.5–δCoPO 4 are further compared to the fully lithiated, isostructural LiCoPO 4 ( Cmcm) phase, for which an improved structure solution as well as Co L 2,3-edge X-ray absorption spectra are reported for the first time.« less

Structural characterisation of the Li argyrodites Li7PS6 and Li7PSe6 and their solid solutions: quantification of site preferences by MAS-NMR spectroscopy.

PubMed

Kong, Shiao Tong; Gün, Ozgül; Koch, Barbara; Deiseroth, Hans Jörg; Eckert, Hellmut; Reiner, Christof

2010-05-03

Li(7)PS(6) and Li(7)PSe(6) belong to a class of new solids that exhibit high Li(+) mobility. A series of quaternary solid solutions Li(7)PS(6-x)Se(x) (0 < or = x < or = 6) were characterised by X-ray crystallography and magic-angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopy. The high-temperature (HT) modifications were studied by single-crystal investigations (both F43m, Z=4, Li(7)PS(6): a=9.993(1) A, Li(7)PSe(6): a=10.475(1) A) and show the typical argyrodite structures with strongly disordered Li atoms. HT-Li(7)PS(6) and HT-Li(7)PSe(6) transform reversibly into low-temperature (LT) modifications with ordered Li atoms. X-ray powder diagrams show the structures of LT-Li(7)PS(6) and LT-Li(7)PSe(6) to be closely related to orthorhombic LT-alpha-Cu(7)PSe(6). Single crystals of the LT modifications are not available due to multiple twinning and formation of antiphase domains. The gradual substitution of S by Se shows characteristic site preferences closely connected to the functionalities of the different types of chalcogen atoms (S, Se). High-resolution solid-state (31)P NMR is a powerful method to differentiate quantitatively between the distinct (PS(4-n)Se(n))(3-) local environments. Their population distribution differs significantly from a statistical scenario, revealing a pronounced preference for P-S over P-Se bonding. This preference, shown for the series of LT samples, can be quantified in terms of an equilibrium constant specifying the melt reaction Se(P)+S(2-) <==>S(P)+Se(2-), prior to crystallisation. The (77)Se MAS-NMR spectra reveal that the chalcogen distributions in the second and third coordination sphere of the P atoms are essentially statistical. The number of crystallographically independent Li atoms in both LT modifications was analysed by means of (6)Li{(7)Li} cross polarisation magic angle spinning (CPMAS).

Direct synthesis and characterization of mixed-valent Li 0.5$-$δCoPO 4, a Li-deficient derivative of the Cmcm polymorph of LiCoPO 4

DOE PAGES

Ludwig, Jennifer; Alarcon-Suesca, Carlos; Geprags, Stephan; ...

2017-05-26

While the majority of research activities on LiCoPO 4 is focussed on the thermodynamically stable olivine-type Pnma polymorph, the metastable Pna2 1 and Cmcm modifications have recently attracted considerable attention due to their interesting material properties. In this study, we present the first Li-deficient structural derivative of the Cmcm modification with the nominal composition Li 0.5–δCoPO 4. As opposed to the substoichiometric olivine ( Pnma) phases Li xCoPO 4 (x = 0; 2/3), which are exclusively accessible by electrochemical or chemical Li extraction techniques, this is also the first time that a direct soft-chemical synthesis route towards a Li xCoPOmore » 4-type material is accomplished. X-ray and neutron diffraction studies indicate that Cmcm-type Li 0.5–δCoPO 4 shows vacancies on both the Li and Co sites, whereas X-ray absorption spectra demonstrate that the structure features heterovalent Co ions (+2/+3) to compensate for the Li deficit. Magnetic measurements reveal a long-range antiferromagnetic order below 10.5 K. A thorough investigation of the thermal stability using thermogravimetric analysis, differential scanning calorimetry, and temperature-dependent in situ X-ray powder diffraction demonstrates that Li 0.5–δCoPO 4 is metastable and exhibits a complex, multi-step thermal decomposition mechanism. In the first step at 394 °C, it decomposes to α-Co 2P 2O 7 ( P2 1/c) and LiCoPO 4 ( Cmcm) upon O 2 release. The LiCoPO 4 ( Cmcm) intermediate is then irreversibly transformed to olivine-type LiCoPO 4 (Pnma) at 686 °C. Furthermore, the material properties of Li 0.5–δCoPO 4 are further compared to the fully lithiated, isostructural LiCoPO 4 ( Cmcm) phase, for which an improved structure solution as well as Co L 2,3-edge X-ray absorption spectra are reported for the first time.« less

The properties of and analytical methods for detection of LiOH and Li2CO3

NASA Technical Reports Server (NTRS)

Selvaduray, Guna

1991-01-01

Lithium hydroxide (LiOH) is used as a CO2 absorbent in the Shuttle Extravehicular Mobility Unit (EMU) Portable Life Support System (PLSS). The first objective was to survey parameters that may be used to indicate conversion of LiOH to Li2CO3, and compile a list of all possible properties, including physical, chemical, structural, and electrical, that may serve to indicate the occurrence of reaction. These properties were compiled for the reactant (LiOH), the intermediate monohydrate compound (LiOH.H2O), and the final product (Li2CO3). The second objective was to survey measurement and analytical techniques which may be used in conjunction with each of the properties identified above, to determine the extent of conversion of LiOH to Li2CO3. Both real-time and post-run techniques were of interest. The techniques were also evaluated in terms of complexity, technology readiness, materials/equipment availability, and cost, where possible.

Thermodynamics of Pb17Li-bismuth interactions

NASA Astrophysics Data System (ADS)

Hubberstey, Peter; Sample, Tony

1994-09-01

Thermodynamic calculations of the PbBiLi ternary system have been completed to rationalise the formation of solid Li 3Bi on reaction of liquid Pb17Li with bismuth. At 723 K, the bismuth activity in equilibrium with liquid Pi17Li and solid Li 3Bi is calculated to be 9.50 × 10 -4; this can be correlated to a solubility of 2.09 × 10 -1 mol% Bi(2520 wppm). The corresponding bismuth activity in equilibrium with liquid Pb17Li and solid LiBi is 5.04 × 10 -2 (an extrapolated value as LiBi decomposes peritectically at 688 K). The minimum lithium content of PbLi alloys required to react with unit activity bismuth to form Li 3Bi at 723 K is calculated to be ˜ 1.8 mol% Li. The dominance of Li 3Bi in the PbBiLi system is attributed to its extreme stability as evidenced by both its high melting point (1418 K) and free energy of formation [ ΔGf0(Li 3Bi, c 723 K) = 212.8 kJ mol -1].

A Li-Garnet composite ceramic electrolyte and its solid-state Li-S battery

NASA Astrophysics Data System (ADS)

Huang, Xiao; Liu, Cai; Lu, Yang; Xiu, Tongping; Jin, Jun; Badding, Michael E.; Wen, Zhaoyin

2018-04-01

A high strength Li-Garnet solid electrolyte composite ceramic is successfully prepared via conventional solid state method with Li6.4La3Zr1.4Ta0.6O12 and nano MgO powders. Well sintered ceramic pellets and bars are obtained with 0-9 wt.% MgO. Fracture strength is approximately 135 MPa for composite ceramics with 5-9 wt.% MgO, which is ∼50% higher than that of pure Li6.4La3Zr1.4Ta0.6O12 (90 MPa). Lithium-ion conductivity of the composite is above 5 × 10-4 S cm-1 at room temperature; comparable to the pure Li6.4La3Zr1.4Ta0.6O12 material. SEM cross-sections of the composite ceramic shows a much more uniform microstructure comparing with pure ones, owing to the grain growth inhibition effect of the MgO second phase. A battery cell consisting of Li/composite ceramics/Sulfur-Carbon at 25 °C exhibits a capacity of 685 mAh g-1 at 0.2 C at the 200th cycle, while maintaining a coulombic efficiency of 100%. These results indicate that the composite ceramic Li6.4La3Zr1.4Ta0.6O12-MgO is promising for the production of electrolyte membrane and fabrication of Li-Sulfur batteries.

Tailoring Anisotropic Li-Ion Transport Tunnels on Orthogonally Arranged Li-Rich Layered Oxide Nanoplates Toward High-Performance Li-Ion Batteries.

PubMed

Xu, Ming; Fei, Linfeng; Zhang, Weibing; Li, Tao; Lu, Wei; Zhang, Nian; Lai, Yanqing; Zhang, Zhian; Fang, Jing; Zhang, Kai; Li, Jie; Huang, Haitao

2017-03-08

High-performance Li-rich layered oxide (LRLO) cathode material is appealing for next-generation Li-ion batteries owing to its high specific capacity (>300 mAh g -1 ). Despite intense studies in the past decade, the low initial Coulombic efficiency and unsatisfactory cycling stability of LRLO still remain as great challenges for its practical applications. Here, we report a rational design of the orthogonally arranged {010}-oriented LRLO nanoplates with built-in anisotropic Li + ion transport tunnels. Such a novel structure enables fast Li + ion intercalation and deintercalation kinetics and enhances structural stability of LRLO. Theoretical calculations and experimental characterizations demonstrate the successful synthesis of target cathode material that delivers an initial discharge capacity as high as 303 mAh g -1 with an initial Coulombic efficiency of 93%. After 200 cycles at 1.0 C rate, an excellent capacity retention of 92% can be attained. Our method reported here opens a door to the development of high-performance Ni-Co-Mn-based cathode materials for high-energy density Li-ion batteries.

Single step transformation of sulphur to Li2S2/Li2S in Li-S batteries

PubMed Central

Helen, M.; Reddy, M. Anji; Diemant, Thomas; Golla-Schindler, Ute; Behm, R. Jürgen; Kaiser, Ute; Fichtner, Maximilian

2015-01-01

Lithium-sulphur batteries have generated tremendous research interest due to their high theoretical energy density and potential cost-effectiveness. The commercial realization of Li-S batteries is still hampered by reduced cycle life associated with the formation of electrolyte soluble higher-order polysulphide (Li2Sx, x = 4–8) intermediates, leading to capacity fading, self-discharge, and a multistep voltage profile. Herein, we have realized a practical approach towards a direct transformation of sulphur to Li2S2/Li2S in lithium-sulphur batteries by alteration of the reaction pathway. A coconut shell derived ultramicroporous carbon-sulphur composite cathode has been used as reaction directing template for the sulphur. The lithiation/delithiation and capacity fading mechanism of microporous carbon confined sulphur composite was revealed by analyzing the subsurface using X-ray photoelectron spectroscopy. No higher-order polysulphides were detected in the electrolyte, on the surface, and in the subsurface of the cathode composite. The altered reaction pathway is reflected by a single-step profile in the discharge/charge of a lithium-sulphur cell. PMID:26173723

Tuning Li-Ion Diffusion in α-LiMn 1–x Fe x PO 4 Nanocrystals by Antisite Defects and Embedded β-Phase for Advanced Li-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Jiangtao; Xiao, Yinguo; Tang, Hanting

Olivine-structured LiMn1-xFexPO4 has become a promising candidate for cathode materials owing to its higher working voltage of 4.1 V and thus larger energy density than that of LiFePO4, which has been used for electric vehicles batteries with the advantage of high safety but disadvantage of low energy density due to its lower working voltage of 3.4 V. One drawback of LiMn1-xFexPO4 electrode is its relatively low electronic and Li-ionic conductivity with Li-ion one-dimensional diffusion. Herein, olivine-structured α-LiMn0.5Fe0.5PO4 nanocrystals were synthesized with optimized Li-ion diffusion channels in LiMn1-xFexPO4 nanocrystals by inducing high concentrations of Fe2+-Li+ antisite defects, which showed impressive capacitymore » improvements of approaching 162, 127, 73, and 55 mAh g-1 at 0.1, 10, 50, and 100 C, respectively, and a long-term cycling stability of maintaining about 74% capacity after 1000 cycles at 10 C. By using high-resolution transmission electron microscopy imaging and joint refinement of hard X-ray and neutron powder diffraction patterns, we revealed that the extraordinary high-rate performance could be achieved by suppressing the formation of electrochemically inactive phase (β-LiMn1-xFexPO4, which is first reported in this work) embedded in α-LiMn0.5Fe0.5PO4. Because of the coherent orientation relationship between β- and α- phases, the β-phase embedded would impede the Li+ diffusion along the [100] and/or [001] directions that was activated by the high density of Fe2+-Li+ antisite (4.24%) in α-phase. Thus, by optimizing concentrations of Fe2+-Li+ antisite defects and suppressing β-phase-embedded olivine structure, Li-ion diffusion properties in LiMn1-xFexPO4 nanocrystals can be tuned by generating new Li+ tunneling. These findings may provide insights into the design and generation of other advanced electrode materials with improved rate performance.« less

Tuning Li-Ion Diffusion in α-LiMn 1–xFe xPO 4 Nanocrystals by Antisite Defects and Embedded β-Phase for Advanced Li-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Jiangtao; Xiao, Yinguo; Tang, Hanting

Olivine-structured LiMn 1–xFe xPO 4 has become a promising candidate for cathode materials owing to its higher working voltage of 4.1 V and thus larger energy density than that of LiFePO 4, which has been used for electric vehicles batteries with the advantage of high safety but disadvantage of low energy density due to its lower working voltage of 3.4 V. One drawback of LiMn 1–xFe xPO 4 electrode is its relatively low electronic and Li-ionic conductivity with Li-ion one-dimensional diffusion. In this paper, olivine-structured α-LiMn 0.5Fe 0.5PO 4 nanocrystals were synthesized with optimized Li-ion diffusion channels in LiMn 1–xFemore » xPO 4 nanocrystals by inducing high concentrations of Fe 2+–Li + antisite defects, which showed impressive capacity improvements of approaching 162, 127, 73, and 55 mAh g –1 at 0.1, 10, 50, and 100 C, respectively, and a long-term cycling stability of maintaining about 74% capacity after 1000 cycles at 10 C. By using high-resolution transmission electron microscopy imaging and joint refinement of hard X-ray and neutron powder diffraction patterns, we revealed that the extraordinary high-rate performance could be achieved by suppressing the formation of electrochemically inactive phase (β-LiMn 1–xFe xPO 4, which is first reported in this work) embedded in α-LiMn 0.5Fe 0.5PO 4. Because of the coherent orientation relationship between β- and α-phases, the β-phase embedded would impede the Li + diffusion along the [100] and/or [001] directions that was activated by the high density of Fe 2+–Li + antisite (4.24%) in α-phase. Thus, by optimizing concentrations of Fe 2+–Li + antisite defects and suppressing β-phase-embedded olivine structure, Li-ion diffusion properties in LiMn 1–xFe xPO 4 nanocrystals can be tuned by generating new Li + tunneling. Finally, these findings may provide insights into the design and generation of other advanced electrode materials with improved rate performance.« less

Tuning Li-Ion Diffusion in α-LiMn 1–xFe xPO 4 Nanocrystals by Antisite Defects and Embedded β-Phase for Advanced Li-Ion Batteries

DOE PAGES

Hu, Jiangtao; Xiao, Yinguo; Tang, Hanting; ...

2017-07-13

Olivine-structured LiMn 1–xFe xPO 4 has become a promising candidate for cathode materials owing to its higher working voltage of 4.1 V and thus larger energy density than that of LiFePO 4, which has been used for electric vehicles batteries with the advantage of high safety but disadvantage of low energy density due to its lower working voltage of 3.4 V. One drawback of LiMn 1–xFe xPO 4 electrode is its relatively low electronic and Li-ionic conductivity with Li-ion one-dimensional diffusion. In this paper, olivine-structured α-LiMn 0.5Fe 0.5PO 4 nanocrystals were synthesized with optimized Li-ion diffusion channels in LiMn 1–xFemore » xPO 4 nanocrystals by inducing high concentrations of Fe 2+–Li + antisite defects, which showed impressive capacity improvements of approaching 162, 127, 73, and 55 mAh g –1 at 0.1, 10, 50, and 100 C, respectively, and a long-term cycling stability of maintaining about 74% capacity after 1000 cycles at 10 C. By using high-resolution transmission electron microscopy imaging and joint refinement of hard X-ray and neutron powder diffraction patterns, we revealed that the extraordinary high-rate performance could be achieved by suppressing the formation of electrochemically inactive phase (β-LiMn 1–xFe xPO 4, which is first reported in this work) embedded in α-LiMn 0.5Fe 0.5PO 4. Because of the coherent orientation relationship between β- and α-phases, the β-phase embedded would impede the Li + diffusion along the [100] and/or [001] directions that was activated by the high density of Fe 2+–Li + antisite (4.24%) in α-phase. Thus, by optimizing concentrations of Fe 2+–Li + antisite defects and suppressing β-phase-embedded olivine structure, Li-ion diffusion properties in LiMn 1–xFe xPO 4 nanocrystals can be tuned by generating new Li + tunneling. Finally, these findings may provide insights into the design and generation of other advanced electrode materials with improved rate performance.« less

Continuous flame aerosol synthesis of carbon-coated nano-LiFePO4 for Li-ion batteries

PubMed Central

Waser, Oliver; Büchel, Robert; Hintennach, Andreas; Novák, Petr; Pratsinis, Sotiris E.

2013-01-01

Core-shell, nanosized LiFePO4-carbon particles were made in one step by scalable flame aerosol technology at 7 g/h. Core LiFePO4 particles were made in an enclosed flame spray pyrolysis (FSP) unit and were coated in-situ downstream by auto thermal carbonization (pyrolysis) of swirl-fed C2H2 in an O2-controlled atmosphere. The formation of acetylene carbon black (ACB) shell was investigated as a function of the process fuel-oxidant equivalence ratio (EQR). The core-shell morphology was obtained at slightly fuel-rich conditions (1.0 < EQR < 1.07) whereas segregated ACB and LiFePO4 particles were formed at fuel-lean conditions (0.8 < EQR < 1). Post-annealing of core-shell particles in reducing environment (5 vol% H2 in argon) at 700 °C for up to 4 hours established phase pure, monocrystalline LiFePO4 with a crystal size of 65 nm and 30 wt% ACB content. Uncoated LiFePO4 or segregated LiFePO4-ACB grew to 250 nm at these conditions. Annealing at 800 °C induced carbothermal reduction of LiFePO4 to Fe2P by ACB shell consumption that resulted in cavities between carbon shell and core LiFePO4 and even slight LiFePO4 crystal growth but better electrochemical performance. The present carbon-coated LiFePO4 showed superior cycle stability and higher rate capability than the benchmark, commercially available LiFePO4. PMID:23407817

Chemical obtaining of LiMO2 and LiM2O4 (M=Co, Mn) oxides, for cathodic applications in Li-ion batteries

NASA Astrophysics Data System (ADS)

Y Neira-Guio, A.; Gómez Cuaspud, J. A.; López, E. Vera; Pineda Triana, Y.

2017-12-01

This paper describes the synthesis and characterization of two spinel and olivine-type multicomponent oxides based on LiMO2 and LiM2O4 systems (M=Co and Mn), which represent the current state of the art in the development of cathodes for Li-ion batteries. A simple combustion synthesis process was employed to obtain the nanometric oxides in powder form (crystal sizes around 5-8nm), with a number of improved surface characteristics. The characterization by X-Ray Diffraction (XRD), Scanning and Transmission Electron Microscopy (SEM, TEM) and X-Ray Fluorescence (XRF), allowed to evaluate the morphology and the stoichiometric compositions of solids, obtaining a concordant pure crystalline phase of LiCoO2 and LiMn2O4 oxides identified in a rhombohedral and cubic phase with punctual group R-3m (1 6 6) and Fm-3m (2 2 5) respectively. The electrical characterization of materials developed by impedance spectroscopy solid state, allowed to determine a p-type semiconducting behaviour with conductivity values of 6.2×10-3 and 2.7×10-7 S for LiCoO2 and LiMn2O4 systems, consistent with the state of the art for such materials.

Nuclear Structure in China 2010

NASA Astrophysics Data System (ADS)

Bai, Hong-Bo; Meng, Jie; Zhao, En-Guang; Zhou, Shan-Gui

2011-08-01

Personal view on nuclear physics research / Jie Meng -- High-spin level structures in [symbol]Zr / X. P. Cao ... [et al.] -- Constraining the symmetry energy from the neutron skin thickness of tin isotopes / Lie-Wen Chen ... [et al.] -- Wobbling rotation in atomic nuclei / Y. S. Chen and Zao-Chun Gao -- The mixing of scalar mesons and the possible nonstrange dibaryons / L. R. Dai ... [et al.] -- Net baryon productions and gluon saturation in the SPS, RHIC and LHC energy regions / Sheng-Qin Feng -- Production of heavy isotopes with collisions between two actinide nuclides / Z. Q. Feng ... [et al.] -- The projected configuration interaction method / Zao-Chun Gao and Yong-Shou Chen -- Applications of Nilsson mean-field plus extended pairing model to rare-earth nuclei / Xin Guan ... [et al.] -- Complex scaling method and the resonant states / Jian-You Guo ... [et al.] -- Probing the equation of state by deep sub-barrier fusion reactions / Hong-Jun Hao and Jun-Long Tian -- Doublet structure study in A[symbol]105 mass region / C. Y. He ... [et al.] -- Rotational bands in transfermium nuclei / X. T. He -- Shape coexistence and shape evolution [symbol]Yb / H. Hua ... [et al.] -- Multistep shell model method in the complex energy plane / R. J. Liotta -- The evolution of protoneutron stars with kaon condensate / Ang Li -- High spin structures in the [symbol]Lu nucleus / Li Cong-Bo ... [et al.] -- Nuclear stopping and equation of state / QingFeng Li and Ying Yuan -- Covariant description of the low-lying states in neutron-deficient Kr isotopes / Z. X. Li ... [et al.] -- Isospin corrections for superallowed [symbol] transitions / HaoZhao Liang ... [et al.] -- The positive-parity band structures in [symbol]Ag / C. Liu ... [et al.] -- New band structures in odd-odd [symbol]I and [symbol]I / Liu GongYe ... [et al.] -- The sd-pair shell model and interacting boson model / Yan-An Luo ... [et al.] -- Cross-section distributions of fragments in the calcium isotopes projectile

LETTER TO THE EDITOR: Cross sections of 6Li(t,d1)7Li*[0.478] and 6Li(t,p1)8Li*[0.981] nuclear reactions in the 0-2 MeV energy range

NASA Astrophysics Data System (ADS)

Voronchev, V. T.; Kukulin, V. I.

2000-12-01

An original extrapolation technique developed previously is modified and applied to study nuclear reactions in the 6Li + T system at energies E = 0-2 MeV. Cross sections of gamma-ray-producing reactions 6Li(t,d1)7Li*[0.478] and 6Li(t,p1)8Li*[0.981] with important diagnostic implications are calculated. The (t,d1) nuclear data found exceed those accepted elsewhere by 2.5-3.5 times at sub-barrier energies. The cross sections of the (t,p1) reaction are calculated for the first time.

Relevance of LiPF6 as Etching Agent of LiMnPO4 Colloidal Nanocrystals for High Rate Performing Li-ion Battery Cathodes.

PubMed

Chen, Lin; Dilena, Enrico; Paolella, Andrea; Bertoni, Giovanni; Ansaldo, Alberto; Colombo, Massimo; Marras, Sergio; Scrosati, Bruno; Manna, Liberato; Monaco, Simone

2016-02-17

LiMnPO4 is an attractive cathode material for the next-generation high power Li-ion batteries, due to its high theoretical specific capacity (170 mA h g(-1)) and working voltage (4.1 V vs Li(+)/Li). However, two main drawbacks prevent the practical use of LiMnPO4: its low electronic conductivity and the limited lithium diffusion rate, which are responsible for the poor rate capability of the cathode. The electronic resistance is usually lowered by coating the particles with carbon, while the use of nanosize particles can alleviate the issues associated with poor ionic conductivity. It is therefore of primary importance to develop a synthetic route to LiMnPO4 nanocrystals (NCs) with controlled size and coated with a highly conductive carbon layer. We report here an effective surface etching process (using LiPF6) on colloidally synthesized LiMnPO4 NCs that makes the NCs dispersible in the aqueous glucose solution used as carbon source for the carbon coating step. Also, it is likely that the improved exposure of the NC surface to glucose facilitates the formation of a conductive carbon layer that is in intimate contact with the inorganic core, resulting in a high electronic conductivity of the electrode, as observed by us. The carbon coated etched LiMnPO4-based electrode exhibited a specific capacity of 118 mA h g(-1) at 1C, with a stable cycling performance and a capacity retention of 92% after 120 cycles at different C-rates. The delivered capacities were higher than those of electrodes based on not etched carbon coated NCs, which never exceeded 30 mA h g(-1). The rate capability here reported for the carbon coated etched LiMnPO4 nanocrystals represents an important result, taking into account that in the electrode formulation 80% wt is made of the active material and the adopted charge protocol is based on reasonable fast charge times.

Toward garnet electrolyte–based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface

PubMed Central

Fu, Kun (Kelvin); Gong, Yunhui; Liu, Boyang; Zhu, Yizhou; Xu, Shaomao; Yao, Yonggang; Luo, Wei; Wang, Chengwei; Lacey, Steven D.; Dai, Jiaqi; Chen, Yanan; Mo, Yifei; Wachsman, Eric; Hu, Liangbing

2017-01-01

Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet–type Li7La3Zr2O12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10−3 to 10−4 S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnet solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm2 for the pristine garnet/Li and 75 ohm·cm2 for the surface-engineered garnet/Li. Li7La2.75Ca0.25Zr1.75Nb0.25O12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries. PMID:28435874

Toward garnet electrolyte–based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, Kun; Gong, Yunhui; Liu, Boyang

Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet–type Li 7La 3Zr 2O 12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10 -3 to 10 -4 S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnetmore » solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm2 for the pristine garnet/Li and 75 ohm·cm 2 for the surface-engineered garnet/Li. Li 7La 2.75Ca 0.25Zr 1.75Nb 0.25O 12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries.« less

Toward garnet electrolyte–based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface

DOE PAGES

Fu, Kun; Gong, Yunhui; Liu, Boyang; ...

2017-04-07

Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet–type Li 7La 3Zr 2O 12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10 -3 to 10 -4 S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnetmore » solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm2 for the pristine garnet/Li and 75 ohm·cm 2 for the surface-engineered garnet/Li. Li 7La 2.75Ca 0.25Zr 1.75Nb 0.25O 12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries.« less

Three-Dimensional Honeycomb-Structural LiAlO2-Modified LiMnPO4 Composite with Superior High Rate Capability as Li-Ion Battery Cathodes.

PubMed

Li, Junzhe; Luo, Shaohua; Ding, Xueyong; Wang, Qing; He, Ping

2018-04-04

In the efforts toward the rapidly increasing demands for high-power application, cathode materials with three-dimensional (3D) architectures have been proposed. Here, we report the construction of the 3D LiAlO 2 -LiMnPO 4 /C cathode materials for lithium-ion batteries in an innovation way. The as-prepared 3D active materials LiMnPO 4 /C and the honeycomb-like Li-ion conductor LiAlO 2 framework are used as working electrode directly without additional usage of polymeric binder. The electrochemical performance has been improved significantly due to the special designed core-shell architectures of LiMnPO 4 /C@LiAlO 2 . The 3D binder-free electrode exhibits high rate capability as well as superior cycling stability with a capability of ∼105 mAh g -1 and 98.4% capacity retention after 100 cycles at a high discharge rate of 10 C. Such synthesis method adopted in our work can be further extended to other promising candidates and would also inspire new avenues of development of 3D materials for lithium-ion batteries.

[100]-Oriented LiFePO4 Nanoflakes toward High Rate Li-Ion Battery Cathode.

PubMed

Li, Zhaojin; Peng, Zhenzhen; Zhang, Hui; Hu, Tao; Hu, Minmin; Zhu, Kongjun; Wang, Xiaohui

2016-01-13

[100] is believed to be a tough diffusion direction for Li(+) in LiFePO4, leading to the belief that the rate performance of [100]-oriented LiFePO4 is poor. Here we report the fabrication of 12 nm-thick [100]-oriented LiFePO4 nanoflakes by a simple one-pot solvothermal method. The nanoflakes exhibit unexpectedly excellent electrochemical performance, in stark contrast to what was previously believed. Such an exceptional result is attributed to a decreased thermodynamic transformation barrier height (Δμb) associated with increased active population.

CuLi2Sn and Cu2LiSn: Characterization by single crystal XRD and structural discussion towards new anode materials for Li-ion batteries.

PubMed

Fürtauer, Siegfried; Effenberger, Herta S; Flandorfer, Hans

2014-12-01

The stannides CuLi 2 Sn (CSD-427095) and Cu 2 LiSn (CSD-427096) were synthesized by induction melting of the pure elements and annealing at 400 °C. The phases were reinvestigated by X-ray powder and single-crystal X-ray diffractometry. Within both crystal structures the ordered CuSn and Cu 2 Sn lattices form channels which host Cu and Li atoms at partly mixed occupied positions exhibiting extensive vacancies. For CuLi 2 Sn, the space group F-43m. was verified (structure type CuHg 2 Ti; a =6.295(2) Å; wR 2 ( F ²)=0.0355 for 78 unique reflections). The 4( c ) and 4( d ) positions are occupied by Cu atoms and Cu+Li atoms, respectively. For Cu 2 LiSn, the space group P 6 3 / mmc was confirmed (structure type InPt 2 Gd; a =4.3022(15) Å, c =7.618(3) Å; wR 2 ( F ²)=0.060 for 199 unique reflections). The Cu and Li atoms exhibit extensive disorder; they are distributed over the partly occupied positions 2( a ), 2( b ) and 4( e ). Both phases seem to be interesting in terms of application of Cu-Sn alloys as anode materials for Li-ion batteries.

Modulation of solid electrolyte interphase of lithium-ion batteries by LiDFOB and LiBOB electrolyte additives

NASA Astrophysics Data System (ADS)

Huang, Shiqiang; Wang, Shuwei; Hu, Guohong; Cheong, Ling-Zhi; Shen, Cai

2018-05-01

Solid-electrolyte interphase (SEI) layer is an organic-inorganic composite layer that allows Li+ transport across but blocks electron flow across and prevents solvent diffusing to electrode surface. Morphology, thickness, mechanical and chemical properties of SEI are important for safety and cycling performance of lithium-ion batteries. Herein, we employ a combination of in-situ AFM and XPS to investigate the effects of two electrolyte additives namely lithium difluoro(oxalate)borate (LiDFOB) and lithium bis(oxalato)borate (LiBOB) on SEI layer. LiDFOB is found to result in a thin but hard SEI layer containing more inorganic species (LiF and LiCO3); meanwhile LiBOB promotes formation of a thick but soft SEI layer containing more organic species such as ROCO2Li. Findings from present study will help development of electrolyte additives that promote formation of good SEI layer.

Equilibrium lithium isotope fractionation in Li-rich minerals

NASA Astrophysics Data System (ADS)

Liu, S.; Li, Y.; Liu, J.

2017-12-01

Lithium is the lightest alkali metal, and only exhibits +1 valence state in minerals. It is widely distributed on the Earth, and usually substitutes for Mg in silicate minerals. Li has two stable isotopes, 6Li and 7Li, with the relative abundances of 7.52% and 92.48%, respectively. The large mass difference between 6Li and 7Li could induce significant isotope fractionation in minerals. Li isotopes can provide an important geochemical tracer for mantle processes. However, the fractionation factors for Li in most minerals remain poorly known, which makes the geochemical implications of Li isotope fractionations in minerals difficult to assess. Here, we try to use the vibrational frequencies obtained by the first-principles methods based on density-functional theory to calculate the Li isotope fractionation parameters for amblygonite (LiAlPO4F), bikitaite (LiSi2AlO7H2), eucryptite (LiAlSiO4), lithiophilite (LiMnPO4), lithiophosphate (Li3PO4), montebrasite (LiAlPO5H), and spodumene (LiAlSi2O6) in the temperature range of 0-1200 ºC. For forsterite (Mg2SiO4) and diopside (CaMgSi2O6) in which Li takes the place of Mg, the equilibrium Li isotope fractionation between them also be studied. Our preliminary calculations show that the coordination number of Li seems to play an important role in controlling Li isotope fractionation in these minerals, and concentration of Li in forsterite and diopside seems to have great effects on Li isotope fractionation factors of them.

Measurements of the fundamental thermodynamic parameters of Li/BCX and Li/SOCl2 cells

NASA Technical Reports Server (NTRS)

Kalu, E. E.; White, R. E.; Darcy, E. C.

1992-01-01

Two experimental techniques - equilibrium or reversible cell discharge and measurement of open circuit potential as a function of temperature - are used to determine the thermodynamic data needed to estimate the heat generation characteristics of Li/BCX and Li/SOCl2 cells. The results obtained showed that the reversible cell potential, the temperature dependence of the reversible cell potential, and the thermoneutral potential of the BCX cell were 3.74 V, -0.857 +/- 0.198 mV/K, and 3.994 +/- 0.0603 V, respectively. The respective values obtained for the Li/SOCl2 cell were 3.67 V, -0.776 +/- 0.255 mV/K, and 3.893 +/- 0.0776 V. The difference between the thermoneutral potential of Li/BCX and Li/SCl2 cells is attributable to the difference in their electroactive components.

Reoxidation of uranium metal immersed in a Li2O-LiCl molten salt after electrolytic reduction of uranium oxide

NASA Astrophysics Data System (ADS)

Choi, Eun-Young; Jeon, Min Ku; Lee, Jeong; Kim, Sung-Wook; Lee, Sang Kwon; Lee, Sung-Jai; Heo, Dong Hyun; Kang, Hyun Woo; Jeon, Sang-Chae; Hur, Jin-Mok

2017-03-01

We present our findings that uranium (U) metal prepared by using the electrolytic reduction process for U oxide (UO2) in a Li2O-LiCl salt can be reoxidized into UO2 through the reaction between the U metal and Li2O in LiCl. Two salt types were used for immersion of the U metal: one was the salt used for electrolytic reduction, and the other was applied to the unused LiCl salts with various concentrations of Li2O and Li metal. Our results revealed that the degree of reoxidation increases with the increasing Li2O concentration in LiCl and that the presence of the Li metal in LiCl suppresses the reoxidation of the U metal.

7Li(d,p)8Li transfer reaction in the NCSM/RGM approach

NASA Astrophysics Data System (ADS)

Raimondi, F.; Hupin, G.; Navrátil, P.; Quaglioni, S.

2018-03-01

Recently, we applied an ab initio method, the no-core shell model combined with the resonating group method, to the transfer reactions with light p-shell nuclei as targets and deuteron as the projectile. In particular, we studied the elastic scattering of deuterium on 7Li and the 7Li(d,p)8Li transfer reaction starting from a realistic two-nucleon interaction. In this contribution, we review of our main results on the 7Li(d,p)8Li transfer reaction, and we extend the study of the relevant reaction channels, by showing the dominant resonant phase shifts of the scattering matrix. We assess also the impact of the polarization effects of the deuteron below the breakup on the positive-parity resonant states in the reaction. For this purpose, we perform an analysis of the convergence trend of the phase and eigenphase shifts, with respect to the number of deuteron pseudostates included in the model space.

Antiperovskite Li 3 OCl superionic conductor films for solid-state Li-ion batteries

DOE PAGES

Lü, Xujie; Howard, John W.; Chen, Aiping; ...

2016-02-02

We prepared antiperovskite Li 3OCl superionic conductor films via pulsed laser deposition using a composite target. A significantly enhanced ionic conductivity of 2.0 × 10 -4 S cm -1 at room temperature is achieved, and this value is more than two orders of magnitude higher than that of its bulk counterpart. Moreover, the applicability of Li 3OCl as a solid electrolyte for Li-ion batteries is demonstrated.

Electrodisintegration of Li 6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bishop, G. R.; Bernheim, M.

1963-06-01

For the ( γ,n) reaction in Li 6 a model in which Li 6 splits into a deuteron and an alpha particle that separately absorb the photon energy was recently proposed. The model was tested by studying the inelastic scattering of 101.4-Mev electrons from Li 6. Expressions for the cross sections were obtained, and values calculated for a form factor in the cross sections confirm the validity of the model.

Single-crystalline LiFePO4 nanosheets for high-rate Li-ion batteries.

PubMed

Zhao, Yu; Peng, Lele; Liu, Borui; Yu, Guihua

2014-05-14

The lithiation/delithiation in LiFePO4 is highly anisotropic with lithium-ion diffusion being mainly confined to channels along the b-axis. Controlling the orientation of LiFePO4 crystals therefore plays an important role for efficient mass transport within this material. We report here the preparation of single crystalline LiFePO4 nanosheets with a large percentage of highly oriented {010} facets, which provide the highest pore density for lithium-ion insertion/extraction. The LiFePO4 nanosheets show a high specific capacity at low charge/discharge rates and retain significant capacities at high C-rates, which may benefit the development of lithium batteries with both favorable energy and power density.

Li-atoms-induced structure changes of Guinier–Preston–Bagaryatsky zones in AlCuLiMg alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, S.Y.; Le, Z.; Chen, Z.K.

2016-11-15

Guinier–Preston–Bagaryatsky (GPB) zones are the well-known strengthening precipitates of AlCuMg alloys formed upon thermal ageing. Here we report that when formed in AlCuLiMg alloys the GPB zones can change significantly in morphology and structure. It is shown that though they do still consist of Al, Cu and Mg elements fundamentally, the GPB zones in AlCuLiMg alloys have a rather different structure due to a featured Li-segregation at their interfaces with the matrix and possible Li-replacement of partial Mg atoms in the structure. As such the Li-containing GPB zones often develop from one-dimensional to quasi-two-dimensional precipitates. - Highlights: • We observemore » Guinier–Preston–Bagaryatsky zone variants in AlCuLiMg alloys. • We obtain atomic-resolution images of the precipitates and model their structures. • Li-atoms play a key role in modifying the structure of these precipitate variants.« less

In-house fabrication and testing capabilities for Li and Li-ion 18650 cells

NASA Astrophysics Data System (ADS)

Nagasubramanian, G.

2010-04-01

For over 10 years Sandia Labs have been involved in an US DOE-funded program aimed at developing electric vehicle batteries for transportation applications. Currently this program is called "Advanced Battery Research (ABR)." In this effort we were preparing 18650 cells with electrodes supplied by or purchased from private companies for thermal abuse and electrical characterization studies. Lately, we are coating our own electrodes, building cells and evaluating performance. This paper describes our extensive in-house facilities for slurry making, electrode coating, cell winding etc. In addition, facilities for electrical testing and thermal abuse will be described. This facility allows us to readjust our focus quickly to the changing demands of the still evolving ABR program. Additionally, we continue to make cells for our internal use. We made several 18650 cells both primary (Li-CFx) and secondary (Li-ion) and evaluated performance. For example Li-CFx cells gave ~2.9Ahr capacity at room temperature. Our high voltage Li-ion cells consisting of carbon anode and cathode based on LiNi 0.4Mn 0.3Co 0.3O2 in organic electrolytes exhibited reproducible behavior and gave capacity on the order of 1Ahr. Performance of Li-ion cells at different temperatures and thermal abuse characteristics will be presented.

A High-Performance Li-O2 Battery with a Strongly Solvating Hexamethylphosphoramide Electrolyte and a LiPON-Protected Lithium Anode.

PubMed

Zhou, Bin; Guo, Limin; Zhang, Yantao; Wang, Jiawei; Ma, Lipo; Zhang, Wen-Hua; Fu, Zhengwen; Peng, Zhangquan

2017-08-01

The aprotic Li-O 2 battery has attracted a great deal of interest because theoretically it can store more energy than today's Li-ion batteries. However, current Li-O 2 batteries suffer from passivation/clogging of the cathode by discharged Li 2 O 2 , high charging voltage for its subsequent oxidation, and accumulation of side reaction products (particularly Li 2 CO 3 and LiOH) upon cycling. Here, an advanced Li-O 2 battery with a hexamethylphosphoramide (HMPA) electrolyte is reported that can dissolve Li 2 O 2 , Li 2 CO 3 , and LiOH up to 0.35, 0.36, and 1.11 × 10 -3 m, respectively, and a LiPON-protected lithium anode that can be reversibly cycled in the HMPA electrolyte. Compared to the benchmark of ether-based Li-O 2 batteries, improved capacity, rate capability, voltaic efficiency, and cycle life are achieved for the HMPA-based Li-O 2 cells. More importantly, a combination of advanced research techniques provide compelling evidence that operation of the HMPA-based Li-O 2 battery is backed by nearly reversible formation/decomposition of Li 2 O 2 with negligible side reactions. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reactive transport modeling of Li isotope fractionation

NASA Astrophysics Data System (ADS)

Wanner, C.; Sonnenthal, E. L.

2013-12-01

The fractionation of Li isotopes has been used as a proxy for interaction processes between silicate rocks and any kind of fluids. In particular, Li isotope measurements are powerful because Li is almost exclusively found in silicate minerals. Moreover, the two stable Li isotopes, 6Li and 7Li, differ by 17% in mass introducing a large mass dependent isotope fractionation even at high temperature. Typical applications include Li isotope measurements along soil profiles and of river waters to track silicate weathering patterns and Li isotope measurements of geothermal wells and springs to assess water-rock interaction processes in geothermal systems. For this contribution we present a novel reactive transport modeling approach for the simulation of Li isotope fractionation using the code TOUGHREACT [1]. It is based on a 6Li-7Li solid solution approach similar to the one recently described for simulating Cr isotope fractionation [2]. Model applications include the simulation of granite weathering along a 1D flow path as well as the simulation of a column experiment related to an enhanced geothermal system. Results show that measured δ7Li values are mainly controlled by (i) the degree of interaction between Li bearing primary silicate mineral phases (e.g., micas, feldspars) and the corresponding fluid, (ii) the Li isotope fractionation factor during precipitation of secondary mineral phases (e.g., clays), (iii) the Li concentration in primary and secondary Li bearing mineral phases and (iv) the proportion of dissolved Li that adsorbs to negatively charged surfaces (e.g., clays, Fe/Al-hydroxides). To date, most of these parameters are not very well constrained. Reactive transport modeling thus currently has to rely on many assumptions. Nevertheless, such models are powerful because they are the only viable option if individual contributions of all potential processes on the resulting (i.e., measured) Li isotopic ratio have to be quantitatively assessed. Accordingly, we

Electrochemical performances of co-substituted (La and Li) LiLa{sub x−y}Li{sub y}Ni{sub 1−x}O{sub 2} cathode materials for rechargeable lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohan, P.; Paruthimal Kalaignan, G., E-mail: pkalaignan@yahoo.com

2013-09-01

Graphical abstract: - Highlights: • LiLa{sub x−y}Li{sub x}Ni{sub 1−x}O{sub 2} powders were prepared by a sol–gel method at 600 °C for 10 h. • LiLa{sub x−y}Li{sub x}Ni{sub 1−x}O{sub 2} powder materials had well defined layer structure, and no impurities. • LiLa{sub 0.10}Li{sub 0.10}Ni{sub 0.80}O{sub 2} crystallite size was reduced compared with those of LiNiO{sub 2}. • Li/LiPF{sub 6}/LiLa{sub x−y}Li{sub x}Ni{sub 1−x}O{sub 2} cells were of high charge/discharge capacity, with columbic efficiency at 25 °C and 45 °C. • LiLa{sub 0.10}Li{sub 0.10}Ni{sub 0.80}O{sub 2} good cyclic stability, rate capability and better 45 °C. - Abstract: Co-substituted LiLa{sub x−y}Li{sub y}Ni{sub 1−x}O{sub 2}more » cathode materials were synthesized by sol–gel method using aqueous solutions of metal nitrates and tartaric acid as chelating agent at 600 °C for 10 h. The structure and electrochemical properties of the synthesized materials were characterized by using XRD, SEM, EDAX, TEM, cyclic voltammetry, charge/discharge and electrochemical impedance spectroscopy. XRD studies revealed a well defined layer structure and a linear variation of lattice parameters with the addition of lanthanum and lithium confirmed phase pure compounds in a rhombohedral structure. TEM and SEM analysis shows that LiLa{sub 0.10}Li{sub 0.10}Ni{sub 0.80}O{sub 2} has smaller particle size and regular morphological structure with narrow size distribution than those of LiNiO{sub 2}. Variations of dual mixing and hexagonal ordering with the substituted elements have enhanced the charge/discharge capacities at both room (25 °C) and elevated temperatures (45 °C), respectively. LiLa{sub 0.10}Li{sub 0.10}Ni{sub 0.80}O{sub 2} had high charge/discharge capacity, low irreversible capacity and better elevated temperature performance.« less

LiF dissolution by anion-binding-agent in LiCF x battery systems: Lower ohmic and interfacial resistance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagasubramanian, Ganesan; Fenton, Kyle Ross

2015-02-01

In this paper we will discuss our preliminary thermal and electrochemical data aimed at developing a robust nonflammable Li-CFx cell capable of wide temperature operation. To accomplish this goal, we are evaluating a thermally stable solvent comprised of an anion binding agent (ABA) and lithium fluoride (LiF), typically at a 1:1 molar ratio. In conventional carbonate based electrolytes, ABA is soluble while LiF remains insoluble. However, the neutral ABA solubilizes LiF and forms a salt complex represented as Li+(ABAF-). We are exploiting this unique feature and apply this strategy to CFx chemistry to improve cell performance, due to the CFxmore » cell chemistry generating LiF as discharge product. Continuous solvation of the salt mixture during discharge allows for utilization of electrolytes initially containing sub stoichiometric amount of LiF. The practical benefits are reduced cell weight, mitigation of electrode fouling, and consequently better low temperature performance. Electrolytes containing dimethyl methyl phosphonate (DMMP), 1M tris(pentafluorophenyl) borane (TPFB) and varying concentrations of LiF (1M; 0.5M and 0.1M) were prepared and characterized for ionic conductivity and voltage stability. In general, ionic conductivity decreases with decreasing LiF concentration. The room temperature conductivity for the DMMP 1M TPFB:1M LiF is ~ 9mS/cm and ~3mS/cm for the 1M TPFB:0.1M LiF. Unlike the conductivity, the electrochemical voltage stability did not vary substantially with LiF concentration and the electrolytes showed a stable voltage window in the range 0-3.5V vs. Li +/Li, which is substantially wider than the Li-CFx cell voltage. Flammability measurement performed at our thermal abuse facility demonstrated that the electrolyte was nonflammable. Discharge performance of CFx materials obtained from several vendors was evaluated in 2032 coin cells at room temperature. Experimental results demonstrate a reduction in ohmic resistance and interfacial

Effect of [Li]/[Nb] ratio on composition and defect structure of Zr:Yb:Tm:LiNbO3 crystals

NASA Astrophysics Data System (ADS)

Liu, Chunrui; Dai, Li; Wang, Luping; Shao, Yu; Yan, Zhehua; Xu, Yuheng

2018-04-01

Zr:Yb:Tm:LiNbO3 crystals with various [Li]/[Nb] ratios (0.946, 1.05, 1.20 and 1.38) were grown by the Czochralski technique. Distribution coefficients of Zr4+, Yb3+ and Tm3+ ions were analyzed by the inductively coupled plasma-atomic emission spectrometer (ICP-AES). The influence of [Li]/[Nb] ratio on the composition and defect structure of Zr:Yb:Tm:LiNbO3 crystals was investigated by X-ray diffraction and IR transmission spectrum. The results show that as the [Li]/[Nb] ratio increases in the melt, the distribution coefficients of Yb3+ and Tm3+ ions both increase while that of Zr4+ ion deceases. When the [Li]/[Nb] ratio increases to 1.20 in the melt, Zr:Yb:Tm:LiNbO3 crystal is nearly stoichiometric. In addition, when the [Li]/[Nb] ratio reaches up to 1.38, NbLi4+ are completely replaced and Li+ starts to impel the Zr4+, Yb3+ and Tm3+ into the normal Li sites.

Determine the Role of Canonical Wnt Signaling in Ovarian Tumorigenesis

DTIC Science & Technology

2012-10-01

Acad Sci U S A, 1999. 96(4): p. 1603-8. 11. Kuilman, T., et al., The essence of senescence. Genes Dev, 2010. 24(22): p. 2463- 79. 12. Bernardi, R...Tu,1 Katherine M. Aird,1 Benjamin G. Bitler,1 Jasmine P. Nicodemus,1 Neil Beeharry,2 Bing Xia,3 Tim J. Yen,2 and Rugang Zhang1,2,* 1Women’s Cancer...Bitler, Jasmine P. Nicodemus, Hua Li, et al. Senescence Wnt5a Suppresses Epithelial Ovarian Cancer by Promoting Cellular Updated Version

Ultra-high Thermal Conductivity of Spider Silk: Protein Function Study with Controlled Structure Change and Comparison

DTIC Science & Technology

2016-01-23

a) Papers published in peer-reviewed journals (N/A for none) Enter List of papers submitted or published that acknowledge ARO support from the start...of the project to the date of this printing. List the papers , including journal references, in the following categories: 11.00 10.00 20.00 18.00...Received Paper 1.00 4.00 3.00 2.00 5.00 8.00 Huan Lin, Shen Xu, Chong Li, Hua Dong, Xinwei Wang. Thermal and electrical conduction in 6.4 nm thin gold films

Fabrication and tritium release property of Li2TiO3-Li4SiO4 biphasic ceramics

NASA Astrophysics Data System (ADS)

Yang, Mao; Ran, Guangming; Wang, Hailiang; Dang, Chen; Huang, Zhangyi; Chen, Xiaojun; Lu, Tiecheng; Xiao, Chengjian

2018-05-01

Li2TiO3-Li4SiO4 biphasic ceramic pebbles have been developed as an advanced tritium breeder due to the potential to combine the advantages of both Li2TiO3 and Li4SiO4. Wet method was developed for the pebble fabrication and Li2TiO3-Li4SiO4 biphasic ceramic pebbles were successfully prepared by wet method using the powders synthesized by hydrothermal method. The tritium release properties of the Li2TiO3-Li4SiO4 biphasic ceramic pebbles were evaluated. The biphasic pebbles exhibited good tritium release property at low temperatures and the tritium release temperature was around 470 °C. Because of the isotope exchange reaction between H2 and tritium, the addition of 0.1%H2 to purge gas He could significantly enhance the tritium gas release and the fraction of molecular form of tritium increased from 28% to 55%. The results indicate that the Li2TiO3-Li4SiO4 biphasic ceramic pebbles fabricated by wet method exhibit good tritium release property and hold promising potential as advanced breeder pebbles.

Properties of the LiCl-KCl-Li2O system as operating medium for pyro-chemical reprocessing of spent nuclear fuel

NASA Astrophysics Data System (ADS)

Mullabaev, Albert; Tkacheva, Olga; Shishkin, Vladimir; Kovrov, Vadim; Zaikov, Yuriy; Sukhanov, Leonid; Mochalov, Yuriy

2018-03-01

Crystallization temperatures (liquidus and solidus) in the LiCl-Li2O and (LiCl-KCl)-Li2O systems with the KCl content of 10 and 20 mol.% were obtained with independent methods of thermal analysis using cooling curves, isothermal saturation, and differential scanning calorimetry. The linear sweep voltammetry was applied to control the time of the equilibrium establishment in the molten system after the Li2O addition, which depended on the composition of the base melt and the concentration of Li2O. The fragments of the binary LiCl-Li2O and quazi-binary [LiCl-KCl(10 mol.%)]-Li2O and [LiCl-KCl(20 mol.%)]-Li2O phase diagrams in the Li2O concentration range from 0 to 12 mol.% were obtained. The KCl presence in the LiCl-KCl-Li2O molten mixture in the amount of 10 and 20 mol.% reduces the liquidus temperature by 30 and 80°, respectively, but the region of the homogeneous molten state of the system is considerably narrowed, which complicates its practical application. The Li2O solubility in the molten LiCl, LiCl-KCl(10 mol.%) and LiCl-KCl(20 mol.%) decreases with increasing the KCl content and is equal to 11.5, 7.7 and 3.9 mol.% at 650°С, respectively. The LiCl-KCl melt with 10 mol.% KCl can be recommended for practical use as a medium for the SNF pyro-chemical reprocessing at temperature below 700 °C.

Basic molten salt process-A new route for synthesis of nanocrystalline Li 4Ti 5O 12-TiO 2 anode material for Li-ion batteries using eutectic mixture of LiNO 3-LiOH-Li 2O 2

NASA Astrophysics Data System (ADS)

Rahman, M. M.; Wang, Jia-Zhao; Hassan, Mohd Faiz; Chou, Shulei; Wexler, David; Liu, Hua-Kun

A nanocrystalline Li 4Ti 5O 12-TiO 2 duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO 3-LiOH-Li 2O 2 at 400-500 °C. The microstructure and morphology of the Li 4Ti 5O 12-TiO 2 product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li 4Ti 5O 12; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li 4Ti 5O 12-TiO 2; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g -1 at 0.2 C, 168 mAh g -1 at 0.5 C, 146 mAh g -1 at 1 C, 135 mAh g -1 at 2 C, and 117 mAh g -1 at 5 C. After 100 cycles, the discharge capacity is 138 mAh g -1 at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li 4Ti 5O 12 and the anatase TiO 2.

Storage and Effective Migration of Li-Ion for Defected β-LiFePO4 Phase Nanocrystals.

PubMed

Guo, Hua; Song, Xiaohe; Zhuo, Zengqing; Hu, Jiangtao; Liu, Tongchao; Duan, Yandong; Zheng, Jiaxin; Chen, Zonghai; Yang, Wanli; Amine, Khalil; Pan, Feng

2016-01-13

Lithium iron phosphate, a widely used cathode material, crystallizes typically in olivine-type phase, α-LiFePO4 (αLFP). However, the new phase β-LiFePO4 (βLFP), which can be transformed from αLFP under high temperature and pressure, is originally almost electrochemically inactive with no capacity for Li-ion battery, because the Li-ions are stored in the tetrahedral [LiO4] with very high activation barrier for migration and the one-dimensional (1D) migration channels for Li-ion diffusion in αLFP disappear, while the Fe ions in the β-phase are oriented similar to the 1D arrangement instead. In this work, using experimental studies combined with density functional theory calculations, we demonstrate that βLFP can be activated with creation of effective paths of Li-ion migration by optimized disordering. Thus, the new phase of βLFP cathode achieved a capacity of 128 mAh g(-1) at a rate of 0.1 C (1C = 170 mA g(-1)) with extraordinary cycling performance that 94.5% of the initial capacity retains after 1000 cycles at 1 C. The activation mechanism can be attributed to that the induced disorder (such as FeLiLiFe antisite defects, crystal distortion, and amorphous domains) creates new lithium migration passages, which free the captive stored lithium atoms and facilitate their intercalation/deintercalation from the cathode. Such materials activated by disorder are promising candidate cathodes for lithium batteries, and the related mechanism of storage and effective migration of Li-ions also provides new clues for future design of disordered-electrode materials with high capacity and high energy density.

Spectroelectrochemistry of EuCl 3 in Four Molten Salt Eutectics; 3 LiCl−NaCl, 3 LiCl−2 KCl, LiCl−RbCl, and 3 LiCl−2 CsCl; at 873 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schroll, Cynthia A.; Chatterjee, Sayandev; Levitskaia, Tatiana

Key electrochemical properties affecting pyroprocessing of nuclear fuel were examined in four eutectic melts using using Eu3+/2+ as a representative probe. We report the electrochemical and spectroelectrochemical behavior of EuCl3 in four molten salt eutectics (3 LiCl – NaCl, 3 LiCl – 2 KCl, LiCl – RbCl and 3 LiCl – 2 CsCl) at 873 K. Cyclic voltammetry was used to determine the redox potential for Eu3+/2+ and the applied potentials for spectroelectrochemistry. Single step chronoabsorptometry and thin-layer spectroelectrochemistry were used to obtain the number of electrons transferred, redox potentials and diffusion coefficients for Eu3+ in each eutectic melt. Themore » redox potentials determined by thin-layer spectroelectrochemistry were extremely close to those obtained using cyclic voltammetry. The redox potential for Eu3+/2+ was most positive in the 3 LiCl - NaCl melt, showed a negative shift in the 3 LiCl - 2 KCl melt, and was the most negative in the LiCl - RbCl and 3 LiCl - 2 CsCl eutectics. The diffusion coefficient for Eu3+ followed this same trend; it was the largest in the 3 LiCl - NaCl melt and the smallest in the LiCl - RbCl and 3 LiCl - 2 CsCl melts. The basic one-electron reversible electron transfer for Eu3+/2+ was not changed by melt composition.« less

THE NEW DETECTIONS OF {sup 7}Li/{sup 6}Li ISOTOPIC RATIO IN THE INTERSTELLAR MEDIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawanomoto, S.; Kajino, T.; Aoki, W.

We have determined the isotopic abundance ratio of {sup 7}Li/{sup 6}Li in the interstellar media (ISMs) along lines of sight to HD169454 and HD250290 using the High-Dispersion Spectrograph on the Subaru Telescope. We also observed {zeta} Oph for comparison with previous data. The observed abundance ratios were {sup 7}Li/{sup 6}Li = 8.1{sup +3.6} {sub -1.8} and 6.3{sup +3.0} {sub -1.7} for HD169454 and HD250290, respectively. These values are in reasonable agreement with those observed previously in the solar neighborhood ISMs within {+-}2{sigma} error bars and are also consistent with our measurement of {sup 7}Li/{sup 6}Li = 7.1{sup +2.9} {sub -1.6}more » for a cloud along the line of sight to {zeta} Oph. This is good evidence for homogeneous mixing and instantaneous recycling of the gas component in the Galactic disk. We also discuss several source compositions of {sup 7}Li, Galactic cosmic-ray interactions, stellar nucleosynthesis, and big bang nucleosynthesis.« less

Thermal and Cycle-Life Behavior of Commercial Li-ion and Li-Polymer Cells

NASA Technical Reports Server (NTRS)

Zimmerman, Albert H.; Quinzio, M. V.

2001-01-01

Accelerated and real-time LEO cycle-life test data will be presented for a range of commercial Li-ion and Li-polymer (gel type) cells indicating the ranges of performance that can be obtained, and the performance screening tests that must be done to assure long life. The data show large performance variability between cells, as well as a highly variable degradation signature during non-cycling periods within the life tests. High-resolution Dynamic Calorimetry data will be presented showing the complex series of reactions occurring within these Li cells as they are cycled. Data will also be presented for cells being tested using an Adaptive Charge Control Algorithm (ACCA) that continuously adapts itself to changes in cell performance, operation, or environment to both find and maintain the optimum recharge over life. The ACCA has been used to prevent all unneeded overcharge for Li cells, NiCd cells and NiH2 cells. While this is important for all these cell types, it is most critical for Li-ion cells, which are not designed with electrochemical tolerance for overcharge.

Li-ion diffusion kinetics in LiCoPO 4 thin films deposited on NASICON-type glass ceramic electrolytes by magnetron sputtering

NASA Astrophysics Data System (ADS)

Xie, J.; Imanishi, N.; Zhang, T.; Hirano, A.; Takeda, Y.; Yamamoto, O.

LiCoPO 4 thin films were deposited on Li 1+ x+ yAl xTi 2- xSi yP 3- yO 12 (LATSP) solid electrolyte by radio frequency magnetron sputtering and were characterized by X-ray diffraction and scanning electron microscope. The films show a (1 1 1) preferred orientation upon annealing and are chemically stable with LATSP up to 600 °C in air. An all-solid-state Li/PEO 18-Li(CF 3SO 2) 2N/LATSP/LiCoPO 4/Au cell was fabricated to investigate the electrochemical performance and Li-ion chemical diffusion coefficients, D˜Li , of the LiCoPO 4 thin films. The potential dependence of D˜Li values of the LiCoPO 4 thin film was investigated by potentiostatic intermittent titration technique and was compared with those of the LiFePO 4 thin film. These results showed that the intercalation mechanism of Li-ion in LiCoPO 4 is different from that in LiFePO 4.

Fast Li-Ion Transport in Amorphous Li 2Si 2O 5: An Ab Initio Molecular Dynamics Simulation

DOE PAGES

Lei, Xueling; Wang, Jie; Huang, Kevin

2016-05-03

The present study reports an ab-initio molecular dynamics (AIMD) simulation of ionic diffusion in the amorphous Li 2Si 2O 5 in a temperature range of 573–823 K. The results show that the amorphous Li 2Si 2O 5 is primarily a Li + conductor with negligible O 2- and Si 4+ contributions. The obtained activation energy of 0.47 eV for Li + diffusion is higher than Na + in the analogue amorphous Na 2Si 2O 5, but close to other types of Li + conductors. The predicted Li + conductivity is on the order of 10 -2 S·cm -1 at 623–823more » K. Our simulations also reveal that Li + in the amorphous Li 2Si 2O 5 diffuses via a hopping mechanism between the nearest sites in the channels formed by two adjacent SiO 4 layers.« less

Synthesis of LiFePO4/Li2SiO3/reduced Graphene Oxide (rGO) Composite via Hydrothermal Method

NASA Astrophysics Data System (ADS)

Arifin, M.; Iskandar, F.; Aimon, A. H.; Munir, M. M.; Nuryadin, B. W.

2016-08-01

LiFePO4 is a type of cathode active material used for lithium ion batteries. It has a high electrochemical performance. However, it suffers from certain disadvantages such as a very low intrinsic electronic conductivity and low ionic diffusion. This study was conducted to increase the conductivity of LiFePO4. We have investigated the addition of Li2SiO3 and reduced graphene oxide (rGO) to LiFePO4. The objective of this research was to synthesize LiFePO4/Li2SiO3/rGO via hydrothermal method. Fourier transform infrared spectroscopy (FTIR) measurement showed that the peaks corresponded to the vibration of LiFePO4/Li2SiO3. Further, X-ray diffraction (XRD) measurement confirmed a single phase of LiFePO4. Finally, scanning electron microscopy (SEM) images showed that rGO was distributed on the LiFePO4/Li2SiO3 structure.

Density functional theory study of lithium diffusion at the interface between olivine-type LiFePO4 and LiMnPO4

NASA Astrophysics Data System (ADS)

Shi, Jianjian; Wang, Zhiguo; Qing Fu, Yong

2016-12-01

Coating LiMnPO4 with a thin layer of LiFePO4 shows a better electrochemical performance than the pure LiFePO4 and LiMnPO4, thus it is critical to understand Li diffusion at their interfaces to improve the performance of electrode materials. Li diffusion at the (1 0 0)\\text{LiFeP{{\\text{O}}4}} //(1 0 0)\\text{LiMnP{{\\text{O}}4}} , (0 1 0)\\text{LiFeP{{\\text{O}}4}} //(0 1 0)\\text{LiMnP{{\\text{O}}4}} , and (0 0 1)\\text{LiFeP{{\\text{O}}4}} //(0 0 1)\\text{LiMnP{{\\text{O}}4}} interfaces between LiFePO4 and LiMnPO4 was investigated using density functional theory. The calculated diffusion energy barriers are 0.55 eV for Li to diffuse along the (0 0 1) interface, 0.44 and 0.49 eV for the Li diffusion inside the LiMnPO4 and along the (1 0 0) interface, respectively. When Li diffuses from the LiFePO4 to LiMnPO4 by passing through the (0 1 0) interfaces, the diffusion barriers are 0.45 and 0.60 eV for the Li diffusions in both sides. The diffusion barriers for Li to diffuse in LiMnPO4 near the interfaces decrease compared with those in the pure LiMnPO4. The calculated diffusion coefficient of Li along the (1 0 0) interface is in the range of 3.65  ×  10-11-5.28  ×  10-12 cm2 s-1, which is larger than that in the pure LiMnPO4 with a value of 7.5  ×  10-14 cm2 s-1. Therefore, the charging/discharging rate performance of the LiMnPO4 can be improved by surface coating with the LiFePO4.

An insight into intrinsic interfacial properties between Li metals and Li10GeP2S12 solid electrolytes.

PubMed

Chen, Bingbing; Ju, Jiangwei; Ma, Jun; Zhang, Jianjun; Xiao, Ruijuan; Cui, Guanglei; Chen, Liquan

2017-11-29

Density functional theory simulations and experimental studies were performed to investigate the interfacial properties, including lithium ion migration kinetics, between lithium metal anode and solid electrolyte Li 10 GeP 2 S 12 (LGPS). The LGPS[001] plane was chosen as the studied surface because the easiest Li + migration pathway is along this direction. The electronic structure of the surface states indicated that the electrochemical stability was reduced at both the PS 4 - and GeS 4 -teminated surfaces. For the interface cases, the equilibrium interfacial structures of lithium metal against the PS 4 -terminated LGPS[001] surface (Li/PS 4 -LGPS) and the GeS 4 -terminated LGPS[001] surface (Li/GeS 4 -LGPS) were revealed based on the structural relaxation and adhesion energy analysis. Solid electrolyte interphases were expected to be formed at both Li/PS 4 -LGPS and Li/GeS 4 -LGPS interfaces, resulting in an unstable state of interface and large interfacial resistance, which was verified by the EIS results of the Li/LGPS/Li cell. In addition, the simulations of the migration kinetics show that the energy barriers for Li + crossing the Li/GeS 4 -LGPS interface were relatively low compared with the Li/PS 4 -LGPS interface. This may contribute to the formation of Ge-rich phases at the Li/LGPS interface, which can tune the interfacial structures to improve the ionic conductivity for future all-solid-state batteries. This work will offer a thorough understanding of the Li/LGPS interface, including local structures, electronic states and Li + diffusion behaviors in all-solid-state batteries.

Dynamic polarizabilities and Van der Waals coefficients for alkali atoms Li, Na and alkali dimer molecules Li2, Na2 and NaLi

NASA Astrophysics Data System (ADS)

Mérawa, M.; Dargelos, A.

1998-07-01

The present paper gives an account of investigations of the polarizability of the alkali atoms Li, Na, diatomics homonuclear and heteronuclear Li2, Na2 and NaLi at SCF (Self Consistent Field) level of approximation and at correlated level, using a time Time-Dependent Gauge Invariant method (TDGI). Our static polarizability values agree with the best experimental and theoretical determinations. The Van der Waals C6 coefficients for the atom-atom, atom-dimer and dimer-dimer interactions have been evaluated. Les polarisabilités des atomes alcalins Li, Na, et des molécules diatomiques homonucléaires et hétéronucléaire Li2, Na2 et NaLi, ont été calculées au niveau SCF (Self Consistent Field) et au niveau corrélé à partir d'une méthode invariante de jauge dépendante du temps(TDGI). Nos valeurs des polarisabilités statiques sont en accord avec les meilleurs déterminations expérimentales et théoriques. Les coefficients C6 de Van de Waals pour les interactions atome-atome, atome-dimère et dimère-dimère ont également été évalués.

Bulk thermal capacity determination for Li/BCX and Li/SOClN2 cells

NASA Technical Reports Server (NTRS)

Kalu, E. E.; White, R. E.; Darcy, E. C.

1992-01-01

The bulk heat capacities of Li/BCX and Li/SOClN2 cells were determined at 0 and 100 percent depth-of-discharge for 2.0 V cut-off voltage, in the temperature range 0 to 60 C by a method that did not involve the destruction of the cell nor the contact of cell with a liquid. The heat capacities are found to be dependent on state-of-charge, increasing with depth-of-discharge. The Li/BCX DD-cell has a lower heat capacity than a high rate Li/SOCl2 D-cell. The results obtained by this method compare favorably well with results reported in the literature through other methods. The bulk heat capacities of the cells did not change significantly in the temperature range 0 to 60 C.

Enabling High Energy Density Li-Ion Batteries through Li{sub 2}O Activation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abouimrane, Ali; Cui, Yanjie; Chen, Zonghai

2016-09-01

Lithium oxide (Li2O) is activated in the presence of a layered composite cathode material (HEM) significantly increasing the energy density of lithium-ion batteries. The degree of activation depends on the current rate, electrolyte salt, and anode type. In full-cell tests, the Li2O was used as a lithium source to counter the first-cycle irreversibility of high-capacity composite alloy anodes. When Li2O is mixed with HEM to serve as a cathode, the electrochemical performance was improved in a full cell having an SiO-SnCoC composite as an anode. The mechanism behind the Li2O activation could also explain the first charge plateau and themore » abnormal high capacity associated with these high energy cathode materials.« less

Correlation of anisotropy and directional conduction in β-Li 3PS 4 fast Li + conductor

DOE PAGES

Chen, Yan; Cai, Lu; Liu, Zengcai; ...

2015-07-06

Our letter reports the correlation of anisotropy and directional conduction in the fast Li + conductor β-Li 3PS 4, one of the low-symmetry crystalline electrolyte candidates. The material has both high conductivity and good stability that serves well for the large-scale energy storage applications of all-solid-state lithium ion batteries. The anisotropic physical properties, demonstrated here by the thermal expansion coefficients, are crucial for compatibility in the solid-state system and battery performance. Neutron and X-ray powder diffraction measurements were done to determine the crystal structure and thermal stability. Moreover, the crystallographic b-axis was revealed as a fast expansion direction, while negligiblemore » thermal expansion was observed along the a-axis around the battery operating temperatures. The anisotropic behavior has its structural origin from the Li + conduction channels with incomplete Li occupancy and a flexible connection of LiS 4 and PS 4 tetrahedra within the framework. This indicates a strong correlation in the direction of the ionic transport in the low-symmetry Li + conductor.« less

Storage and Effective Migration of Li-Ion for Defected β-LiFePO 4 Phase Nanocrystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Hua; Song, Xiaohe; Zhuo, Zengqing

2016-01-13

Lithium iron phosphate, a widely used cathode material, crystallizes typically in olivine-type phase, α-LiFePO4 (αLFP). However, the new phase β-LiFePO4 (βLFP), which can be transformed from αLFP under high temperature and pressure, is originally almost electrochemically inactive with no capacity for Li-ion battery, because the Li-ions are stored in the tetrahedral [LiO4] with very high activation barrier for migration and the one-dimensional (1D) migration channels for Li-ion diffusion in αLFP disappear, while the Fe ions in the β-phase are oriented similar to the 1D arrangement instead. In this work, using experimental studies combined with density functional theory calculations, we demonstratemore » that βLFP can be activated with creation of effective paths of Li-ion migration by optimized disordering. Thus, the new phase of βLFP cathode achieved a capacity of 128 mAh g–1 at a rate of 0.1 C (1C = 170 mA g–1) with extraordinary cycling performance that 94.5% of the initial capacity retains after 1000 cycles at 1 C. The activation mechanism can be attributed to that the induced disorder (such as FeLiLiFe antisite defects, crystal distortion, and amorphous domains) creates new lithium migration passages, which free the captive stored lithium atoms and facilitate their intercalation/deintercalation from the cathode. Such materials activated by disorder are promising candidate cathodes for lithium batteries, and the related mechanism of storage and effective migration of Li-ions also provides new clues for future design of disordered-electrode materials with high capacity and high energy density.« less

Li-ion transport in all-solid-state lithium batteries with LiCoO 2 using NASICON-type glass ceramic electrolytes

NASA Astrophysics Data System (ADS)

Xie, J.; Imanishi, N.; Zhang, T.; Hirano, A.; Takeda, Y.; Yamamoto, O.

LiCoO 2 thin films were deposited on the NASICON-type glass ceramics, Li 1+ x+ yAl xTi 2- xSi yP 3- yO 12, by radio frequency (RF) magnetron sputtering and were annealed at different temperatures. The as-deposited and the annealed LiCoO 2 thin films were characterized by X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM). It was found that the films exhibited a (1 0 4) preferred orientation after annealing and Co 3O 4 was observed by annealing over 500 °C due to the reaction between the LiCoO 2 and the glass ceramics. The effect of annealing temperature on the interfacial resistance of glass ceramics/LiCoO 2 and Li-ion transport in the bulk LiCoO 2 thin film was investigated by galvanostatic cycling, cyclic voltammetry (CV), potentiostatic intermittent titration technique (PITT) and electrochemical impedance spectroscopy (EIS) with the Li/PEO/glass ceramics/LiCoO 2 cell. The cell performance was limited by the Li-ion diffusion resistance in Ohara/LiCoO 2 interface as well as in bulk LiCoO 2.

Relaxation-phenomena in LiAl/FeS-cells

NASA Astrophysics Data System (ADS)

Borger, W.; Kappus, W.; Panesar, H. S.

A theoretical model of the capacity of strongly relaxing electrochemical systems is applied to the LiAl/FeS system. Relaxation phenomena in LiAl and FeS electrodes can be described by this model. Experimental relaxation data indicate that lithium transport through the alpha-LiAl layer to the particle surface is the capacity limiting process at high discharge current density in the LiAl electrode in LiCl-KCl and LiF-LiCl-LiBr mixtures. Strong relaxation is observed in the FeS electrode with LiCl-KCl electrolyte caused by lithium concentration gradients and precipitation of KCl in the pores.

From chemistry to mechanics: bulk modulus evolution of Li-Si and Li-Sn alloys via the metallic electronegativity scale.

PubMed

Li, Keyan; Xie, Hui; Liu, Jun; Ma, Zengsheng; Zhou, Yichun; Xue, Dongfeng

2013-10-28

Toward engineering high performance anode alloys for Li-ion batteries, we proposed a useful method to quantitatively estimate the bulk modulus of binary alloys in terms of metallic electronegativity (EN), alloy composition and formula volume. On the basis of our proposed potential viewpoint, EN as a fundamental chemistry concept can be extended to be an important physical parameter to characterize the mechanical performance of Li-Si and Li-Sn alloys as anode materials for Li-ion batteries. The bulk modulus of binary alloys is linearly proportional to the combination of average metallic EN and atomic density of alloys. We calculated the bulk moduli of Li-Si and Li-Sn alloys with different Li concentrations, which can agree well with the reported data. The bulk modulus of Li-Si and Li-Sn alloys decreases with increasing Li concentration, leading to the elastic softening of the alloys, which is essentially caused by the decreased strength of constituent chemical bonds in alloys from the viewpoint of EN. This work provides a deep understanding of mechanical failure of Si and Sn anodes for Li-ion batteries, and permits the prediction of the composition dependent bulk modulus of various lithiated alloys on the basis of chemical formula, metallic EN and cell volume (or alloy density), with no structural details required.

Composite Li metal anode with vertical graphene host for high performance Li-S batteries

NASA Astrophysics Data System (ADS)

Zhang, Y. J.; Liu, S. F.; Wang, X. L.; Zhong, Y.; Xia, X. H.; Wu, J. B.; Tu, J. P.

2018-01-01

Efficient and stable operation of a lithium metal anode has become the enabling factor for next-generation high energy density storage system. Here, vertical graphene (VG) arrays are used as the scaffold structure for high performance Li metal batteries. The melt infusion method is employed to encapsulate Li inside the VG scaffold structure, and the lithiophilic Si layer is coated onto the array surface by magnetron sputtering to assist this melt-infusion process. The porous scaffold structure can control the volume expansion and inhibit the formation of dendritic lithium significantly, leading to the excellent electrochemical performance of the Li composite anode. In addition, the Li-S full batteries with the composite anode display enhanced cycling reversibility.

Li Anode Technology for Improved Performance

NASA Technical Reports Server (NTRS)

Chen, Tuqiang

2011-01-01

A novel, low-cost approach to stabilization of Li metal anodes for high-performance rechargeable batteries was developed. Electrolyte additives are selected and used in Li cell electrolyte systems, promoting formation of a protective coating on Li metal anodes for improved cycle and safety performance. Li batteries developed from the new system will show significantly improved battery performance characteristics, including energy/power density, cycle/ calendar life, cost, and safety.

Effects of traditional Chinese patent medicine on essential hypertension: a systematic review.

PubMed

Xiong, Xingjiang; Wang, Pengqian; Zhang, Yuqing; Li, Xiaoke

2015-02-01

that focus on mortality and cardiovascular events during long-term follow-up are warranted before TCPM can be recommended for hypertensive patients. Two TCPMs, Song ling xue mai kang capsules and Yang xue qing nao granules, should be prioritized for further research.

Pressure-induced ferroelectric to paraelectric transition in LiTaO 3 and (Li,Mg)TaO 3

DOE PAGES

Yamanaka, Takamitsu; Nakamoto, Yuki; Takei, Fumihiko; ...

2016-02-16

X-ray powder diffraction and Raman scattering of LiTaO 3 (LT) and (Li,Mg)TaO 3 (LMT) have been measured under pressure up to 46 GPa. Above 30 GPa, the ferroelectric rhombohedral phase (R3c, Z – 6) of LiTaO 3 transforms to a paraelectric orthorhombic phase (Pnma with Z – 4) with a large hysteresis. Rietveld profile fitting analysis shows that the Li-O bond is compressed and approaches that of Ta-O with pressure. The cation distribution analysis of the orthorhombic perovskite structure shows that Li and Ta are located in the octahedral 8-fold coordination sites. Difference Fourier |F obs(hkl)| - |F cal(hkl)| mapsmore » of LiTaO 3 and (Li,Mg)TaO 3 indicate polarization in the c axis direction and a more distinct electron density distribution around the Ta position for (Li,Mg)TaO 3 compared to LiTaO 3. The observed effective charges indicate that for (Li,Mg)TaO 3 without vacancies Ta 5+ becomes less ionized as a function of Mg substitution. Considering both site occupancy and effective charge analysis, Ta 5+ is reduced to Ta 4.13+. Mg 2+ and O 2- change to Mg 1.643+ and O 1.732 -, respectively. The space- and time-averaged structures of the dynamical vibration of atoms can be elucidated from the electron density analysis by difference Fourier and temperature factors T(hkl) in the structure refinement. The refinement of the temperature factor is consistent with the cation distribution assuming full stoichiometry. The residual electron density induced from the excess electron in (Li,Mg)TaO 3 indicates more electrons around the Ta site, as confirmed by the effective charge analysis. Raman spectra of LiTaO 3 and (Li,Mg)TaO 3 show notable changes over the measured pressure range. Raman peaks centered at 250 cm –1 and 350 cm –1 at ambient pressure merge above 8 GPa, which we associate with the diminishing of difference in distances between Li-O and Ta-O bonds with pressure in both materials. Finally, Raman spectra show significant changes at 28 GPa and 33 GPa for

Composited reduced graphene oxide into LiFePO4/Li2SiO3 and its electrochemical impedance spectroscopy properties

NASA Astrophysics Data System (ADS)

Arifin, M.; Rus, Y. B.; Aimon, A. H.; Iskandar, F.; Winata, T.; Abdullah, M.; Khairurrijal, K.

2017-03-01

LiFePO4 is commonly used as cathode material for Li-ion batteries due to its stable operational voltage and high specific capacity. However, it suffers from certain disadvantages such as low intrinsic electronic conductivity and low ionic diffusion. This study was conducted to analyse the effect of reduced graphene oxide (rGO) on the electrochemical properties of LiFePO4/Li2SiO3 composite. This composite was synthesized by a hydrothermal method. Fourier transform infrared spectroscopy measurement identified the O-P-O, Fe-O, P-O, and O-Si-O- bands in the LiFePO4/Li2SiO3 composite. X-ray diffraction measurement confirmed the formation of LiFePO4. Meanwhile, Raman spectroscopy confirmed the number of rGO layers. Further, scanning electron microscopy images showed that rGO was distributed around the LiFePO4/Li2SiO3 particles. Finally, the electrochemical impedance spectroscopy results showed that the addition of 1 wt% of rGO to the LiFePO4/Li2SiO3 composite reduced charge transfer resistance. It may be concluded that the addition of 1 wt% rGO to LiFePO4/Li2SiO3 composite can enhance its electrochemical performance as a cathode material.

Rechargeable LiNiO2/carbon cells

NASA Astrophysics Data System (ADS)

Dahn, J. R.; von Sacken, U.; Juzkow, M. W.; Al-Janaby, H.

1991-08-01

Rechargeable cells can be made using two different intercalation compounds, in which the chemical potential of the intercalant differs by several eV, for the electrodes. The factors that play a role in the selection of appropriate lithium intercalation compounds for such cells are discussed. For the ease of cell assembly, the cathode should be stable in air when it is fully intercalated, like LiNiO2. For the anode, the chemical potential of the intercalated Li should be close to that of Li metal, like it is in Li(x)C6. The intercalation of Li in LiNiO2 is discussed, and then in petroleum coke. Then, it is shown that LiNiO2/coke cells have high energy density, long cycle life, excellent high-temperature performance, low self-discharge rates, can be repeatedly discharged to zero volts without damage, and are easily fabricated. It is considered that this type of cell shows far more promise for widespread applications than traditional secondary Li cells using metallic Li anodes.

Capturing and Processing Soil GHG Fluxes Using the LI-COR LI-8100A

NASA Astrophysics Data System (ADS)

Xu, Liukang; McDermitt, Dayle; Hupp, Jason; Johnson, Mark; Madsen, Rod

2015-04-01

The LI-COR LI-8100A Automated Soil CO2 Flux System is designed to measure soil CO2 efflux using automated chambers and a non-steady state measurement protocol. While CO2 is an important gas in many contexts, it is not the only gas of interest for many research applications. With some simple plumbing modifications, many third party analyzers capable of measuring other trace gases, e.g. N2O, CH4, or 13CO2 etc., can be interfaced with the LI-8100A System, and LI-COR's data processing software (SoilFluxPro™) can be used to compute fluxes for these additional gases. In this paper we describe considerations for selecting an appropriate third party analyzer to interface with the system, how to integrate data into the system, and the procedure used to compute fluxes of additional gases in SoilFluxPro™. A case study is presented to demonstrate methane flux measurements using an Ultra-Portable Greenhouse Gas Analyzer (Ultra-Portable GGA, model 915-0011), manufactured by Los Gatos Research and integrated into the LI-8100A System. Laboratory and field test results show that the soil CO2 efflux based on the time series of CO2 data measured either with the LI-8100A System or with the Ultra-Portable GGA are essentially the same. This suggests that soil GHG fluxes measured with both systems are reliable.

Genetic trail for the early migrations of Aisin Gioro, the imperial house of the Qing dynasty.

PubMed

Wei, Lan-Hai; Yan, Shi; Yu, Ge; Huang, Yun-Zhi; Yao, Da-Li; Li, Shi-Lin; Jin, Li; Li, Hui

2017-03-01

The House of Aisin Gioro, the imperial clan of Qing dynasty (1644-1911), affected the history of China and the formation of Manchu ethnicity greatly. However, owing to the lack of historical records and archeological evidences, the origin of the House of Aisin Gioro remains ambiguous. To clarify the origin of Aisin Gioro clan, we conducted whole Y-chromosome sequencing on three samples and Y-single-nucleotide polymorphism (Y-SNP) genotyping on other four samples beside those reported in previous work. We confirmed that the paternal lineage of the Aisin Gioro clan belongs to haplogroup C3b1a3a2-F8951, a brother branch of C3*-Star Cluster (currently named as C3b1a3a1-F3796, once linked to Genghis Khan), which is quite different from the predominant lineage C3c-M48 in other Tungusic-speaking populations. We also determined a series of unique Y-SNP markers for the Aisin Gioro clan. Diversity analyses of haplogroup C3b1a3a2-F8951 revealed the early migration of the ancestors of the Aisin Gioro clan from the middle reaches of Amur River to their later settlement in southeastern Manchuria. Hence, our results suggest that the Aisin Gioro clan may be descendants of ancient populations in Transbaikal region and closely related to origin of current Daur populations. Our research indicated that detailed research of stemma and deep sequencing of Y chromosomes are helpful to explore the prehistoric activities of populations lacking historical records and archeological evidences.

Li4SiO4-Based Artificial Passivation Thin Film for Improving Interfacial Stability of Li Metal Anodes.

PubMed

Kim, Ji Young; Kim, A-Young; Liu, Guicheng; Woo, Jae-Young; Kim, Hansung; Lee, Joong Kee

2018-03-14

An amorphous SiO 2 (a-SiO 2 ) thin film was developed as an artificial passivation layer to stabilize Li metal anodes during electrochemical reactions. The thin film was prepared using an electron cyclotron resonance-chemical vapor deposition apparatus. The obtained passivation layer has a hierarchical structure, which is composed of lithium silicide, lithiated silicon oxide, and a-SiO 2 . The thickness of the a-SiO 2 passivation layer could be varied by changing the processing time, whereas that of the lithium silicide and lithiated silicon oxide layers was almost constant. During cycling, the surface of the a-SiO 2 passivation layer is converted into lithium silicate (Li 4 SiO 4 ), and the portion of Li 4 SiO 4 depends on the thickness of a-SiO 2 . A minimum overpotential of 21.7 mV was observed at the Li metal electrode at a current density of 3 mA cm -2 with flat voltage profiles, when an a-SiO 2 passivation layer of 92.5 nm was used. The Li metal with this optimized thin passivation layer also showed the lowest charge-transfer resistance (3.948 Ω cm) and the highest Li ion diffusivity (7.06 × 10 -14 cm 2 s -1 ) after cycling in a Li-S battery. The existence of the Li 4 SiO 4 artificial passivation layer prevents the corrosion of Li metal by suppressing Li dendritic growth and improving the ionic conductivity, which contribute to the low charge-transfer resistance and high Li ion diffusivity of the electrode.

The influence of temperature and salinity on the Li/Ca and d7Li of inorganic and biogenic carbonates

NASA Astrophysics Data System (ADS)

Marriott, C.; Staubwasser, M.; Crompton, R.; Henderson, G.

2003-04-01

Lithium is the sixth most abundant metal in the ocean. It is conservative with a residence time of around 1Ma and has two stable isotopes ^7Li and ^6Li that are not actively involved in biological processes. Isotopic fractionation is observed during incorporation into calcium carbonate but no previous work has systematically examined the controls on this fractionation. We have investigated Li incorporation and isotopic fraction in both inorganically precipitated calcite and coralline aragonite (1). In both cases there is an inverse correlation of Li concentration with temperature and no significant variation in isotopic fractionation. A decrease in D Li/Ca from 0.0092 to 0.0030 is seen over a temperature range of 5--30^oC, whilst an offset of approximately -8.5 ppm is seen in the δ^7Li ratio relative to the growth solution. The temperature dependence of Li/Ca has an increased sensitivity at low temperatures and might therefore be useful in examining changes in bottom water temperature. We are now investigating Li/Ca and δ^7Li of foraminifera. Previous work (2) has suggested little variability in Li/Ca with temperature, although this was for samples from warmer water where Li/Ca is not sensitive. In this study, Uvigerina are examined in a series of core top samples from the Arabian Sea with a depth range of 95--1800m and corresponding temperature range of 5--20^oC. A series of inorganic calcite samples have also been precipitated in order to examine the effect of salinity on Li/Ca, δ^7Li and δ44Ca over a salinity range of 10--50 psu. The distribution coefficient of Li shows a positive correlation with salinity over this range. δ^7Li and δ44Ca measurements for these samples are presently being analysed. (1) Marriott et al., 2002, GCA, 66, A485 (2) Delaney et al., 1985, GCA, 49, 1327

The effect of Li2CO3 substitution on synthesis of LiBOB compounds as salt of electrolyte battery lithium ion

NASA Astrophysics Data System (ADS)

Lestariningsih, Titik; Wigayati, Etty Marty; Sabrina, Qolby; Prihandoko, Bambang; Priyono, Slamet

2018-04-01

Development of the synthesis of LiB(C2O4)2 compounds continues to evolve along with the need for electrolyte salts to support the research of the manufacture of lithium ion batteries. A study had been conducted on the effect of Li2CO3 substitution on the synthesis of LiB(C2O4)2 or LiBOB compounds. LiBOB was a major candidate to replace LiPF6 as a highly toxic lithium battery electrolyte and harmful to human health. Synthesis of Lithium bis(oxalato) borate used powder metallurgy method. The raw materials used are H2C2O4.2H2O, Li2CO3 or LiOH and H2BO3 from Merck Germany products. The materials are mixed with 2: 1: 1 mol ratio until homogeneous. The synthesis of LiBOB refers to previous research, where the heating process was done gradually. The first stage heating is carried out at 120°C for 4 hours, then the next stage heating is carried out at 240°C for 7 hours. The sample variation in this study was to distinguish the lithium source from Li2CO3 and LiOH. Characterization was done by XRD to know the phase formed, FTIR to confirm that functional group of LiB(C2O4)2 compound, SEM to know the morphological structure, and TG/DTA to know the thermal properties. The results of the analysis shows that LiBOB synthesis using Lithium source from Li2CO3 has succeeded to form LiBOB compound with more LiBOB phase composition is 59.1% and 40.9% LiBOB hydrate phase, SEM morphology shows powder consist of elongated round particle porous and similar to LiBOB commercial and show higher thermal stability.

Development of many-body polarizable force fields for Li-battery applications: 2. LiTFSI-doped Oligoether, polyether, and carbonate-based electrolytes.

PubMed

Borodin, Oleg; Smith, Grant D

2006-03-30

A quantum chemistry study of Li(+) interactions with ethers, carbonates, alkanes, and a trifluoromethanesulfonylimide anion (TFSI(-)) was performed at the MP2, B3LYP, and HF levels using the aug-cc-pvDz basis set for solvents and TFSI(-) anion, and [8s4p3d/5s3p2d]-type basis set for Li. A classical many-polarizable force field was developed for the LiTFSI salt interacting with ethylene carbonate (EC), gamma-butyrolactone (GBL), dimethyl carbonate (DMC), acetone, oligoethers, n-alkanes, and perfluoroalkanes. Molecular dynamics (MD) simulations were performed for EC/LiTFSI, PC/LiTFSI, GBL/LiTFSI, DMC/LiTFSI, 1,2-dimethoxyethane/LiTFSI, pentaglyme/LiTFSI, and poly(ethylene oxide) (MW = 2380)/LiTFSI electrolytes at temperatures from 298 to 423 K and salt concentrations from 0.3 to 5 M. The ion and solvent self-diffusion coefficients, electrolyte conductivity, electrolyte density, LiTFSI apparent molar volumes, and structure of the Li(+) cation environment predicted by MD simulations were found in good agreement with experimental data.

Excellent rate capability and cycling stability in Li+-conductive Li2SnO3-coated LiNi0.5Mn1.5O4 cathode materials for lithium-ion batteries.

PubMed

Mou, Jirong; Deng, Yunlong; Song, Zhicui; Zheng, Qiaoji; Lam, Kwok Ho; Lin, Dunmin

2018-05-22

High-voltage LiNi0.5Mn1.5O4 is a promising cathode candidate for lithium-ion batteries (LIBs) due to its considerable energy density and power density, but the material generally undergoes serious capacity fading caused by side reactions between the active material and organic electrolyte. In this work, Li+-conductive Li2SnO3 was coated on the surface of LiNi0.5Mn1.5O4 to protect the cathode against the attack of HF, mitigate the dissolution of Mn ions during cycling and improve the Li+ diffusion coefficient of the materials. Remarkable improvement in cycling stability and rate performance has been achieved in Li2SnO3-coated LiNi0.5Mn1.5O4. The 1.0 wt% Li2SnO3-coated LiNi0.5Mn1.5O4 cathode exhibits excellent cycling stability with a capacity retention of 88.2% after 150 cycles at 0.1 C and rate capability at high discharge rates of 5 C and 10 C, presenting discharge capacities of 119.5 and 112.2 mAh g-1, respectively. In particular, a significant improvement in cycling stability at 55 °C is obtained after the coating of 1.0 wt% Li2SnO3, giving a capacity retention of 86.8% after 150 cycles at 1 C and 55 °C. The present study provides a significant insight into the effective protection of Li-conductive coating materials for a high-voltage LiNi0.5Mn1.5O4 cathode material.

Electrodeposition of Mg-Li-Al-La Alloys on Inert Cathode in Molten LiCl-KCl Eutectic Salt

NASA Astrophysics Data System (ADS)

Han, Wei; Chen, Qiong; Sun, Yi; Jiang, Tao; Zhang, Milin

2011-12-01

Electrochemical preparation of Mg-Li-Al-La alloys on inert electrodes was investigated in LiCl-KCl melt at 853 K (580 °C). Cyclic voltammograms (CVs) and square wave voltammograms (SWVs) show that the existence of AlCl3 or AlF3 could promote La deposition on an active Al substrate, which is predeposited on inert electrodes. All electrochemical tests show that the reduction of La3+ is a one-step reduction process with three electrons exchanged. The reduction of La(III)→La(0) occurred at -2.04 V, and the underpotential deposition (UPD) of La was detected at -1.55 V ( vs Ag/AgCl). The same phenomena concerning La UPD were observed on two inert cathodes, W and Mo. In addition, Mg-Li-Al-La alloys were obtained by galvanostatic electrolysis on the W cathode from La2O3 in LiCl-KCl-MgCl2-KF melts with aluminum as the anode. X-ray diffraction (XRD) measurements indicated that various phases like the Al2La, Al12Mg17, and βLi phase (LiMg/Li3Mg7) existed in the Mg-Li-Al-La alloys. The distribution of Mg, Al, and La in Mg-Li-Al-La alloys from the analysis of a scan electron micrograph (SEM) and energy dispersive spectrometry (EDS) indicated that the elements Mg, Al, and La distributed homogeneously in the alloys.

Electrochemical characteristics of Li/LiMn 2O 4 cells using gel polymer electrolytes

NASA Astrophysics Data System (ADS)

Kim, Dong-Won; Ko, Jang-Myoun; Chun, Jong-Han

Gel polymer electrolytes composed of acrylonitrile-methylmethacrylate (AM) copolymer and 1 M LiClO 4-ethylene carbonate (EC)/propylene carbonate (PC) are prepared. The ionic conductivity reaches 1.9×10 -3 S cm -1 in a gel polymer electrolyte with 20 wt.% of AM copolymer and 80 wt.% of LiClO 4-EC/PC at room temperature. These systems showed no solvent exudation from the matrix polymer due to enhanced compatibility between AM copolymer and organic liquid electrolyte. A Li/gel polymer electrolyte/LiMn 2O 4 cell has a reversible capacity of 132 mAh g -1 in the voltage range of 3.0-4.3 V at the C/5 rate and shows good cycling performance with a coulombic efficiency >99%.

Simulation and analysis of stress in a Li-ion battery with a blended LiMn2O4 and LiNi0.8Co0.15Al0.05O2 cathode

NASA Astrophysics Data System (ADS)

Dai, Yiling; Cai, Long; White, Ralph E.

2014-02-01

Stress generation due to Li ion insertion into/extraction from LiMn2O4 particles is studied with a mathematical model for a lithium ion battery with pure LiMn2O4 or mixed LiMn2O4 and LiNi0.8Co0.15Al0.05O2 cathode. The simulated stress profile in a pure LiMn2O4 electrode shows nonuniformity across the positive electrode. The cathode blended model predicts that the stress generated in the LiMn2O4 particles is reduced at the end of discharge due to adding LiNi0.8Co0.15Al0.05O2 to the cathode. The effect of the variation in the blend ratio on the stress generation is also investigated.

High resolution Li depth profiling of solid state Li ion battery by TERD technique with high energy light ions

NASA Astrophysics Data System (ADS)

Morita, K.; Tsuchiya, B.; Ohnishi, J.; Yamamoto, T.; Iriyama, Y.; Tsuchida, H.; Majima, T.; Suzuki, K.

2018-07-01

Li depth profiles in Au/Si/LiPON/LCO/Au (LCO = LiCoO2, LiPON = Li3.3PO3.8N0.2) thin films battery under charging condition, prepared on self-supporting Al substrate, have been in situ measured by means of transmission elastic recoil detection (TERD) and Rutherford backscattering spectroscopy (RBS) techniques not only with 5.4 MeV He2+ ion beam without absorber, but also 9 MeV O4+ ion beam with Al absorber. In experiments with 5.4 MeV He2+, well-resolved step-wise TERD spectra have been observed, from which thickness and Li composition of constituent films of the battery are directly estimated. The Li transport from LCO to Si films through LiPON as well as return-back of Li from Si to LCO films and Li leakage into the Al substrate out of the battery system by over-charging under charging condition have been observed in the experiments both 5.4 MeV He2+ and 9 MeV O4+. The latter result indicates that these techniques are applicable to testing degradation of the battery performance by repetition of charging and discharging. Both results are compared in details with each other.

Radiation and Thermal Transformations of Hydrogen Defects in Li6F and LiF:OH

NASA Astrophysics Data System (ADS)

Akhvlediani, Z. G.; Akhvlediani, I. G.

2010-11-01

Hydrogen and tritium defects formed in LiF under the action of neutron radiation under different conditions have been studied. It is shown that U-centers are registered in LiF:OH without additional heating of the sample after irradiation. The behavior of H0 and T0 atoms in Li6 F irradiated at 20 K was studied, and the places of their stabilization were established.

On the thermal behavior of model Li-Li xCoO 2 systems containing ionic liquids in standard electrolyte solutions

NASA Astrophysics Data System (ADS)

Larush, L.; Borgel, V.; Markevich, E.; Haik, O.; Zinigrad, E.; Aurbach, D.; Semrau, G.; Schmidt, M.

We report herein on the possibility of using ionic liquids (ILs) as additives to conventional electrolyte solutions, based on alkyl carbonates and LiPF 6 for attenuating thermal reactions in Li battery systems. As a model, a Li-Li 0.5CoO 2 system was used. The ionic liquids chosen included cations based on derivatives of pyrrolidinium and imidazolium, and the anions bioxalato borate (C 4O 8B -, BOB), (CH 3SO 2) 2N - (TFSI), and PF 3(C 2S 5) 3 - (FAP). The thermal behavior of solutions alone, solutions with Li metal, Li 0.5CoO 2 and Li metal + Li 0.5CoO 2 was studied. It was found that the presence of 10% of ILs, with derivatives of pyrrolidinium cations and FAP or TFSI anions in standard EC-DMC/LiPF 6 solutions, improves considerably the thermal stability of Li 0.5CoO 2 in electrolyte solutions. The onset temperatures of the thermal reactions of Li 0.5CoO 2 with solution species are higher and their heat evolution is considerably lower, when they contain these ionic liquids as additives. This finding opens the door for further studies and optimization of the use of selected ILs as additives that may improve the safety features of Li-ion batteries.

Li-adsorption on doped Mo2C monolayer: A novel electrode material for Li-ion batteries

NASA Astrophysics Data System (ADS)

Mehta, Veenu; Tankeshwar, K.; Saini, Hardev S.

2018-04-01

A first principle calculation has been used to study the electronic and magnetic properties of pristine and N/Mn-doped Mo2C with and without Li-adsorption. The pseudopotential method implemented in SIESTA code based on density functional theory with generalized gradient approximation (GGA) as exchange-correlation (XC) potential has been employed. Our calculated results revealed that the Li gets favorably adsorbed on the hexagonal centre in pristine Mo2C and at the top of C-atom in case of N/Mn-doped Mo2C. The doping of Mn and N atom increases the adsorption of Li in Mo2C monolayer which may results in enhancement of storage capacity in Li-ion batteries. The metallic nature of Li-adsorbed pristine and N/Mn-doped Mo2C monolayer implies a good electronic conduction which is crucial for anode materials for its applications in rechargeable batteries. Also, the open circuit voltage for single Li-adsorption in doped Mo2C monolayer comes in the range of 0.4-1.0 eV which is the optimal range for any material to be used as an anode material. Our result emphasized the enhanced performance of doped Mo2C as an anode material in Li-ion batteries.

Lost in Translation (LiT)

PubMed Central

Dollery, Colin T

2014-01-01

Translational medicine is a roller coaster with occasional brilliant successes and a large majority of failures. Lost in Translation 1 (‘LiT1’), beginning in the 1950s, was a golden era built upon earlier advances in experimental physiology, biochemistry and pharmacology, with a dash of serendipity, that led to the discovery of many new drugs for serious illnesses. LiT2 saw the large-scale industrialization of drug discovery using high-throughput screens and assays based on affinity for the target molecule. The links between drug development and university sciences and medicine weakened, but there were still some brilliant successes. In LiT3, the coverage of translational medicine expanded from molecular biology to drug budgets, with much greater emphasis on safety and official regulation. Compared with R&D expenditure, the number of breakthrough discoveries in LiT3 was disappointing, but monoclonal antibodies for immunity and inflammation brought in a new golden era and kinase inhibitors such as imatinib were breakthroughs in cancer. The pharmaceutical industry is trying to revive the LiT1 approach by using phenotypic assays and closer links with academia. LiT4 faces a data explosion generated by the genome project, GWAS, ENCODE and the ‘omics’ that is in danger of leaving LiT4 in a computerized cloud. Industrial laboratories are filled with masses of automated machinery while the scientists sit in a separate room viewing the results on their computers. Big Data will need Big Thinking in LiT4 but with so many unmet medical needs and so many new opportunities being revealed there are high hopes that the roller coaster will ride high again. PMID:24428732

The Use of Redox Mediators for Enhancing Utilization of Li2S Cathodes for Advanced Li-S Battery Systems.

PubMed

Meini, Stefano; Elazari, Ran; Rosenman, Ariel; Garsuch, Arnd; Aurbach, Doron

2014-03-06

The development of Li2S electrodes is a crucial step toward industrial manufacturing of Li-S batteries, a promising alternative to Li-ion batteries due to their projected two times higher specific capacity. However, the high voltages needed to activate Li2S electrodes, and the consequent electrolyte solution degradation, represent the main challenge. We present a novel concept that could make feasible the widespread application of Li2S electrodes for Li-S cell assembly. In this concept, the addition of redox mediators as additives to the standard electrolyte solution allows us to recover most of Li2S theoretical capacity in the activation cycle at potentials as low as 2.9 VLi, substantially lower than the typical potentials >4 VLi needed with standard electrolyte solution. Those novel additives permit us to preserve the electrolyte solution from being degraded, allowing us to achieve capacity as high as 500 mAhg(-1)Li2S after 150 cycles with no major structural optimization of the electrodes.

Dopant occupancy and exposure energy in Hf:Nd:LiNbO3 crystal as a function of [Li]/[Nb] ratios

NASA Astrophysics Data System (ADS)

Dai, Li; Liu, Chunrui; Han, Xianbo; Yan, Zhehua; Tan, Chao; Wang, Luping; Xu, Yuheng

2017-09-01

A series of Hf: Nd: LiNbO3 crystals with various [Li]/[Nb] ratios ([Li]/[Nb] = 0.94, 1.05, 1.20, 1.38) in the melt were grown by conventional Czochralski technique. The distribution coefficients of Hf4+ and Nd3+ ions were recorded by an inductively coupled plasma-atomic emission spectrometer (ICP-AES). The effective distribution coefficient of Hf4+ is reduced and that of Nd3+ is increased with the increase of [Li]/[Nb] ratio in the melts. In all cases, the effective distribution coefficients is less than 1. The IR transmission spectroscopy of the Hf: Nd: LiNbO3 crystals were measured, getting the results that Hf: Yb: Ho: LiNbO3 crystals with 1.05 [Li]/[Nb] ratios was the stoichiometric. The optical damage resistance ability of Hf:Nd:LiNbO3 crystals were studied by light-induced scattering exposure energy flux threshold method and it increases with the increasing of [Li]/[Nb] ratios. When the [Li]/[Nb] ratio is 1.38 in the melt (the sample 4#), the exposure energy achieves 687.35 J/cm2, approximately 441 folds than that of the sample 1# ([Li]/[Nb] = 0.94) in magnitude.

Data mining of molecular dynamics data reveals Li diffusion characteristics in garnet Li7La3Zr2O12

NASA Astrophysics Data System (ADS)

Chen, Chi; Lu, Ziheng; Ciucci, Francesco

2017-01-01

Understanding Li diffusion in solid conductors is essential for the next generation Li batteries. Here we show that density-based clustering of the trajectories computed using molecular dynamics simulations helps elucidate the Li diffusion mechanism within the Li7La3Zr2O12 (LLZO) crystal lattice. This unsupervised learning method recognizes lattice sites, is able to give the site type, and can identify Li hopping events. Results show that, while the cubic LLZO has a much higher hopping rate compared to its tetragonal counterpart, most of the Li hops in the cubic LLZO do not contribute to the diffusivity due to the dominance of back-and-forth type jumps. The hopping analysis and local Li configuration statistics give evidence that Li diffusivity in cubic LLZO is limited by the low vacancy concentration. The hopping statistics also shows uncorrelated Poisson-like diffusion for Li in the cubic LLZO, and correlated diffusion for Li in the tetragonal LLZO in the temporal scale. Further analysis of the spatio-temporal correlation using site-to-site mutual information confirms the weak site dependence of Li diffusion in the cubic LLZO as the origin for the uncorrelated diffusion. This work puts forward a perspective on combining machine learning and information theory to interpret results of molecular dynamics simulations.

Y-doped Li 8ZrO 6: A Li-Ion Battery Cathode Material with High Capacity

DOE PAGES

Huang, Shuping; Wilson, Benjamin E.; Wang, Bo; ...

2015-08-11

We study—experimentally and theoretically—the energetics, structural changes, and charge flows during the charging and discharging processes for a new high-capacity cathode material, Li 8ZrO 6 (LZO), which we study both pure and yttrium-doped. We quantum mechanically calculated the stable delithiated configurations, the delithiation energy, the charge flow during delithiation, and the stability of the delithiated materials. We find that Li atoms are easier to extract from tetrahedral sites than octahedral ones. We calculate a large average voltage of 4.04 eV vs Li/Li + for delithiation of the first Li atom in a primitive cell, which is confirmed by galvanostatic charge/dischargemore » cycling data. Energy calculations indicate that topotactic delithiation is kinetically favored over decomposition into Li, ZrO 2, and O 2 during the charging process, although the thermodynamic energy of the topotactic reaction is less favorable. When one or two lithium atoms are extracted from a primitive cell of LZO, its volume and structure change little, whereas extraction of the third lithium greatly distorts the layered structure. The Li 6ZrO 6 and Li 5ZrO 6 delithiation products can be thermodynamically metastable to release of O 2. Experimentally, materials with sufficiently small particle size for efficient delithiation and relithiation were achieved within an yttrium-doped LZO/carbon composite cathode that exhibited an initial discharge capacity of at least 200 mAh/g over the first 10 cycles, with 142 mAh/g maintained after 60 cycles. Computations predict that during the charging process, the oxygen ion near the Li vacancy is oxidized for both pure LZO and yttrium-doped LZO, which leads to a small-polaron hole.« less

Y-doped Li 8ZrO 6: A Li-Ion Battery Cathode Material with High Capacity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Shuping; Wilson, Benjamin E.; Wang, Bo

We study—experimentally and theoretically—the energetics, structural changes, and charge flows during the charging and discharging processes for a new high-capacity cathode material, Li 8ZrO 6 (LZO), which we study both pure and yttrium-doped. We quantum mechanically calculated the stable delithiated configurations, the delithiation energy, the charge flow during delithiation, and the stability of the delithiated materials. We find that Li atoms are easier to extract from tetrahedral sites than octahedral ones. We calculate a large average voltage of 4.04 eV vs Li/Li + for delithiation of the first Li atom in a primitive cell, which is confirmed by galvanostatic charge/dischargemore » cycling data. Energy calculations indicate that topotactic delithiation is kinetically favored over decomposition into Li, ZrO 2, and O 2 during the charging process, although the thermodynamic energy of the topotactic reaction is less favorable. When one or two lithium atoms are extracted from a primitive cell of LZO, its volume and structure change little, whereas extraction of the third lithium greatly distorts the layered structure. The Li 6ZrO 6 and Li 5ZrO 6 delithiation products can be thermodynamically metastable to release of O 2. Experimentally, materials with sufficiently small particle size for efficient delithiation and relithiation were achieved within an yttrium-doped LZO/carbon composite cathode that exhibited an initial discharge capacity of at least 200 mAh/g over the first 10 cycles, with 142 mAh/g maintained after 60 cycles. Computations predict that during the charging process, the oxygen ion near the Li vacancy is oxidized for both pure LZO and yttrium-doped LZO, which leads to a small-polaron hole.« less

Simulation of First-Charge Oxygen-Dimerization and Mn-Migration in Li-Rich Layered Oxides xLi 2MnO 3 ·(1 – x )Li MO 2 and Implications for Voltage Fade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benedek, Roy; Iddir, Hakim

The instabilities of Li-rich layered oxide xLi 2MnO 3•(1-x)LiMO 2 (lithium-ion-battery cathode materials) during the first charge are investigated using first-principles dynamical simulation. To complement our earlier simulations for (x = 0.4, M = Ni 0.5Mn 0.5), we address here: pure Li 2MnO 3; small x; M compositions that include Co; a composite with Co spinel: Li 2MnO 3•Li 2M 2O 4; a Li 2MnO 3 slab. Lastly, we discuss how the threshold fraction f of Li 2(1-f)MnO 3 delithiation at which instabilities occur at the surface, fth(surface), differs from that in the bulk, f th(bulk). Approaches to inhibit voltagemore » fade are discussed.« less

Simulation of First-Charge Oxygen-Dimerization and Mn-Migration in Li-Rich Layered Oxides xLi 2MnO 3 ·(1 – x )Li MO 2 and Implications for Voltage Fade

DOE PAGES

Benedek, Roy; Iddir, Hakim

2017-03-08

The instabilities of Li-rich layered oxide xLi 2MnO 3•(1-x)LiMO 2 (lithium-ion-battery cathode materials) during the first charge are investigated using first-principles dynamical simulation. To complement our earlier simulations for (x = 0.4, M = Ni 0.5Mn 0.5), we address here: pure Li 2MnO 3; small x; M compositions that include Co; a composite with Co spinel: Li 2MnO 3•Li 2M 2O 4; a Li 2MnO 3 slab. Lastly, we discuss how the threshold fraction f of Li 2(1-f)MnO 3 delithiation at which instabilities occur at the surface, fth(surface), differs from that in the bulk, f th(bulk). Approaches to inhibit voltagemore » fade are discussed.« less

The crystalline phases present in carbon cathodes of discharged Li/SOCl/sub 2/-LiAlCl/sub 4/ cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, R.M.; Surampudi, S.; Bankston, C.P.

1989-05-01

The authors describe the x-ray diffraction patterns of 100% discharged Schawinigan black cathodes from Li/SOCl/sub 2-/LiAlCl/sub 4/ cells obtained using a high resolution Guinier camera. The previous assignments of the diffraction lines to Li/sub 2/O/sub 2/ and rhombohedral sulfur are all found to be incorrect; all sharp Bragg diffraction lines not assignable to anhydrous LiCl can be assigned to LiCl1 . H/sub 2/O.

Some optical properties of KTP, LiIO3, and LiNbO3

NASA Technical Reports Server (NTRS)

Gettemy, Donald J.; Harker, William C.; Lindholm, Glenn; Barnes, Norman P.

1988-01-01

Measurements of the absorption coefficient for KTP, LiIO3, and LiNbO3 are discussed. The variation of the refractive index with temperature has been measured for KTP and LiIO3. It is necessary to know both the absorption coefficient beta and the variation in the indexes of refraction with temperature change dn/dT to determine the average power limit of a nonlinear interaction. With the dn/dT information, it is also possible to estimate the temperature half width of any nonlinear interaction by calculating the variation of the phase-matching condition with temperature.

Synthesis and optical characterization of LiKB4O7, Li2B6O10, and LiCsB6O10 glasses.

PubMed

Adamiv, V; Teslyuk, I; Dyachok, Ya; Romanyuk, G; Krupych, O; Mys, O; Martynyuk-Lototska, I; Burak, Ya; Vlokh, R

2010-10-01

In the current work we report on the synthesis of LiKB(4)O(7), Li(2)B(6)O(10), and LiCsB(6)O(10) borate glasses. The results for their piezo-optic, acousto-optic, acoustic, elastic, refractive, optical transmission, and optical resistance properties are also presented. It is shown that some of these glasses represent efficient acousto-optic materials that are transparent down to the vacuum ultraviolet range and highly resistant to laser radiation.

Electrochemical Codeposition of Al-Li-Mg Alloys at Solid Aluminum Electrode from LiCl-KCl-MgCl2 Molten Salt System

NASA Astrophysics Data System (ADS)

Ye, Ke; Zhang, Mi Lin; Chen, Ye; Han, Wei; de Yan, Yong; Cao, Peng

2010-06-01

The electrochemical codeposition of Mg and Li at an aluminium electrode in LiCl-KCl (50:50 wt pct) melts containing different concentrations of MgCl2 at 893 K (620 °C) to form Al-Li-Mg alloys was investigated. Cyclic voltammograms showed that the potential of Li metal deposition at an Al electrode, before the addition of MgCl2, is more positive than that of Li metal deposition at an Mo electrode, which indicated the formation of an Al-Li alloy. The underpotential deposition of magnesium at an aluminium electrode leads to the formation of Al-Mg alloys, and the succeeding underpotential deposition of lithium on predeposited Al-Mg alloys leads to the formation of Al-Li-Mg alloys. Chronopotentiometric measurements indicated that the codeposition of Mg and Li occurs at current densities lower than -0.668 A cm-2 in LiCl-KCl-MgCl2 (8 wt pct) melts at an aluminium electrode. The chronoamperometric studies indicated that the onset potential for the codeposition of Mg and Li is -2.000 V, and the codeposition of Mg and Li at an aluminium electrode is formed into Al-Li-Mg alloys when the applied potentials are more negative than -2.000 V. X-ray diffraction and inductively coupled plasma analysis indicated that Al-Li-Mg alloys with different lithium and magnesium contents were prepared via potentiostatic and galvanostatic electrolysis. The microstructure of typical dual phases of the Al-Li-Mg alloy was characterized by an optical microscope and by scanning electron microscopy. The analysis of energy dispersive spectrometry showed that the elements of Al and Mg distribute homogeneously in the Al-Li-Mg alloy. The lithium and magnesium contents of Al-Li-Mg alloys can be controlled by MgCl2 concentrations and by electrolytic parameters.

A Stable, Magnetic, and Metallic Li3O4 Compound as a Discharge Product in a Li-Air Battery.

PubMed

Yang, Guochun; Wang, Yanchao; Ma, Yanming

2014-08-07

The Li-air battery with the specific energy exceeding that of a Li ion battery has been aimed as the next-generation battery. The improvement of the performance of the Li-air battery needs a full resolution of the actual discharge products. Li2O2 has been long recognized as the main discharge product, with which, however, there are obvious failures on the understanding of various experimental observations (e.g., magnetism, oxygen K-edge spectrum, etc.) on discharge products. There is a possibility of the existence of other Li-O compounds unknown thus far. Here, a hitherto unknown Li3O4 compound as a discharge product of the Li-air battery was predicted through first-principles swarm structure searching calculations. The new compound has a unique structure featuring the mixture of superoxide O2(-) and peroxide O2(2-), the first such example in the Li-O system. The existence of superoxide O2(-) creates magnetism and hole-doped metallicity. Findings of Li3O4 gave rise to direct explanations of the unresolved experimental magnetism, triple peaks of oxygen K-edge spectra, and the Raman peak at 1125 cm(-1) of the discharge products. Our work enables an opportunity for the performance of capacity, charge overpotential, and round-trip efficiency of the Li-air battery.

Emergence of Metallic Properties at LiFePO4 Surfaces and LiFePO4/Li2S Interfaces: An Ab Initio Study.

PubMed

Timoshevskii, Vladimir; Feng, Zimin; Bevan, Kirk H; Zaghib, Karim

2015-08-26

The atomic and electronic structures of the LiFePO4 (LFP) surface, both bare and reconstructed upon possible oxygenation, are theoretically studied by ab initio methods. On the basis of total energy calculations, the atomic structure of the oxygenated surface is proposed, and the effect of surface reconstruction on the electronic properties of the surface is clarified. While bare LFP(010) surface is insulating, adsorption of oxygen leads to the emergence of semimetallic behavior by inducing the conducting states in the band gap of the system. The physical origin of these conducting states is investigated. We further demonstrate that deposition of Li2S layers on top of oxygenated LFP(010) surface leads to the formation of additional conducting hole states in the first layer of Li2S surface because of the charge transfer from sulfur p-states to the gap states of LFP surface. This demonstrates that oxygenated LFP surface not only provides conducting layers itself, but also induces conducting channels in the top layer of Li2S. These results help to achieve further understanding of potential role of LFP particles in improving the performance of Li-S batteries through emergent interface conductivity.

cathode material for Li-ion batteries

NASA Astrophysics Data System (ADS)

Wang, Yanming; Wang, Yajing; Wang, Fei

2014-05-01

Well-crystallized Li2NiTiO4 nanoparticles are rapidly synthesized by a molten salt method using a mixture of NaCl and KCl salts. X-ray diffraction pattern and scanning electron microscopic image show that Li2NiTiO4 has a cubic rock salt structure with an average particle size of ca. 50 nm. Conductive carbon-coated Li2NiTiO4 is obtained by a facile ball milling method. As a novel 4 V positive cathode material for Li-ion batteries, the Li2NiTiO4/C delivers high discharge capacities of 115 mAh g-1 at room temperature and 138 mAh g-1 and 50°C, along with a superior cyclability.

Data mining of molecular dynamics data reveals Li diffusion characteristics in garnet Li7La3Zr2O12

PubMed Central

Chen, Chi; Lu, Ziheng; Ciucci, Francesco

2017-01-01

Understanding Li diffusion in solid conductors is essential for the next generation Li batteries. Here we show that density-based clustering of the trajectories computed using molecular dynamics simulations helps elucidate the Li diffusion mechanism within the Li7La3Zr2O12 (LLZO) crystal lattice. This unsupervised learning method recognizes lattice sites, is able to give the site type, and can identify Li hopping events. Results show that, while the cubic LLZO has a much higher hopping rate compared to its tetragonal counterpart, most of the Li hops in the cubic LLZO do not contribute to the diffusivity due to the dominance of back-and-forth type jumps. The hopping analysis and local Li configuration statistics give evidence that Li diffusivity in cubic LLZO is limited by the low vacancy concentration. The hopping statistics also shows uncorrelated Poisson-like diffusion for Li in the cubic LLZO, and correlated diffusion for Li in the tetragonal LLZO in the temporal scale. Further analysis of the spatio-temporal correlation using site-to-site mutual information confirms the weak site dependence of Li diffusion in the cubic LLZO as the origin for the uncorrelated diffusion. This work puts forward a perspective on combining machine learning and information theory to interpret results of molecular dynamics simulations. PMID:28094317

RETRACTED: Association between the ACE I/D gene polymorphism and T2DN susceptibility: The risk of T2DM developing into T2DN in the Asian population.

PubMed

Zhong, Weiqiang; Jiang, Zongpei; Zhou, Tian-Biao

2015-12-01

.1177/1470320314566019 Tian-Biao Zhou, Xue-Feng Guo, Zongpei Jiang, and Hong-Yan Li Relationship between the ACE I/D gene polymorphism and T1DN susceptibility/risk of T1DM developing into T1DN in the Caucasian population Journal of Renin-Angiotensin-Aldosterone System 1470320314563425, first published on February 1, 2015 doi: 10.1177/1470320314563425 Chun-Hua Yang and Tian-Biao Zhou Relationship between the angiotensinogen A1166C gene polymorphism and the risk of diabetes mellitus developing into diabetic nephropathy Journal of Renin-Angiotensin-Aldosterone System 1470320314566221, first published on February 1, 2015 doi: 10.1177/1470320314566221 Chun-Hua Yang and Tian-Biao Zhou Association of the ACE I/D gene polymorphism with sepsis susceptibility and sepsis progression Journal of Renin-Angiotensin-Aldosterone System 1470320314568521, first published on February 3, 2015 doi: 10.1177/1470320314568521 Articles published in an issue Guohui Liu, Tian-Biao Zhou, Zongpei Jiang, and Dongwen Zheng Association of ACE I/D gene polymorphism with T2DN susceptibility and the risk of T2DM developing into T2DN in a Caucasian population Journal of Renin-Angiotensin-Aldosterone System March 2015 16: 165-171, first published on November 14, 2014 doi: 10.1177/1470320314557849 Weiqiang Zhong, Zhongliang Huang, Yong Wu, Zongpei Jiang, and Tian-Biao Zhou Association of aldosterone synthase (CYP11B2) gene polymorphism with IgA nephropathy risk and progression of IgA nephropathy Journal of Renin-Angiotensin-Aldosterone System September 2015 16: 660-665, first published on August 20, 2014 doi: 10.1177/1470320314524011.

Dehydrogenation kinetics and reversibility of LiAlH4-LiBH4 doped with Ti-based additives and MWCNT

NASA Astrophysics Data System (ADS)

Thaweelap, Natthaporn; Utke, Rapee

2016-11-01

Dehydrogenation kinetics and reversibility of LiAlH4-LiBH4 doped with Ti-based additives (TiCl3 and Ti-isopropoxide), multiwall carbon nanotubes (MWCNT), and MWCNT impregnated with Ti-based additives are proposed. Reduction of dehydrogenation temperature as well as improvements of kinetics and reversibility, especially decomposition of thermodynamically stable hydride (LiBH4) is obtained from the samples doped with Ti-isopropoxide and MWCNT. This can be due to the fact that the formations of LixAl(1-x)B2 and LiH-Al containing phase during dehydrogenation favor decomposition of LiH, leading to increment of hydrogen capacity, and stabilization of boron in solid state, resulting in improvement of reversibility. Besides, the curvatures and thermal conductivity of MWCNT benefit hydrogen diffusion and heat transfer during de/rehydrogenation. Nevertheless, deficient hydrogen content reversible is observed in all samples due to the irreversible of LiAlH4 and/or Li3AlH6 as well as the formation of stable phase (Li2B12H12) during de/rehydrogenation.

Quantum Chemical Insight into the LiF Interlayer Effects in Organic Electronics: Reactions between Al Atom and LiF Clusters.

PubMed

Wu, Shui-Xing; Kan, Yu-He; Li, Hai-Bin; Zhao, Liang; Wu, Yong; Su, Zhong-Min

2015-08-06

It is well known that the aluminum cathode performs dramatically better when a thin lithium fluoride (LiF) layer inserted in organic electronic devices. The doping effect induced by the librated Li atom via the chemical reactions producing AlF3 as byproduct was previously proposed as one of possible mechanisms. However, the underlying mechanism discussion is quite complicated and not fully understood so far, although the LiF interlayer is widely used. In this paper, we perform theoretical calculations to consider the reactions between an aluminum atom and distinct LiF clusters. The reaction pathways of the Al-(LiF)n (n = 2, 4, 16) systems were discovered and the energetics were theoretically evaluated. The release of Li atom and the formation of AlF3 were found in two different chemical reaction routes. The undissociated Al-(LiF)n systems have chances to change to some structures with loosely bound electrons. Our findings about the interacted Al-(LiF)n systems reveal new insights into the LiF interlayer effects in organic electronics applications.

Improved charging performance of Li-O2 batteries by forming Ba-incorporated Li2O2 as the discharge product

NASA Astrophysics Data System (ADS)

Matsuda, Shoichi; Uosaki, Kohei; Nakanishi, Shuji

2017-06-01

Although Li-O2 batteries can potentially achieve greater than two-fold higher energy densities than Li-ion batteries, the basic performance of Li-O2 batteries remains poor. In particular, the large over-potential of positive electrode reactions during the charging process results in low round-trip energy efficiency and limited cycle life, and is therefore the main barrier to the practical use of rechargeable Li-O2 batteries. In the present study, we demonstrate that the charging performance of Li-O2 batteries can be significantly improved by simply adding barium (Ba) ions into the electrolyte. Elemental analysis revealed that Ba-incorporated Li2O2 was obtained as the main discharge product of a Li-O2 cell operated in the presence of Ba2+. Notably, the improvement of charging performance was confirmed to originate from the Ba-incorporated Li2O2 deposits, rather than the Ba2+ present in the electrolyte. The present results suggest that the incorporation of heteroatoms into the discharge product is an effective approach for improving the charging performance of Li-O2 batteries.

Facile molten salt synthesis of Li2NiTiO4 cathode material for Li-ion batteries.

PubMed

Wang, Yanming; Wang, Yajing; Wang, Fei

2014-01-01

Well-crystallized Li2NiTiO4 nanoparticles are rapidly synthesized by a molten salt method using a mixture of NaCl and KCl salts. X-ray diffraction pattern and scanning electron microscopic image show that Li2NiTiO4 has a cubic rock salt structure with an average particle size of ca. 50 nm. Conductive carbon-coated Li2NiTiO4 is obtained by a facile ball milling method. As a novel 4 V positive cathode material for Li-ion batteries, the Li2NiTiO4/C delivers high discharge capacities of 115 mAh g(-1) at room temperature and 138 mAh g(-1) and 50°C, along with a superior cyclability.

Facile molten salt synthesis of Li2NiTiO4 cathode material for Li-ion batteries

PubMed Central

2014-01-01

Well-crystallized Li2NiTiO4 nanoparticles are rapidly synthesized by a molten salt method using a mixture of NaCl and KCl salts. X-ray diffraction pattern and scanning electron microscopic image show that Li2NiTiO4 has a cubic rock salt structure with an average particle size of ca. 50 nm. Conductive carbon-coated Li2NiTiO4 is obtained by a facile ball milling method. As a novel 4 V positive cathode material for Li-ion batteries, the Li2NiTiO4/C delivers high discharge capacities of 115 mAh g-1 at room temperature and 138 mAh g-1 and 50°C, along with a superior cyclability. PMID:24855459

Li-S batteries: Firing for compactness

NASA Astrophysics Data System (ADS)

Li, Yanguang; Chen, Fengjiao

2017-07-01

Conventional Li-S batteries have a non-compact cathode structure containing low areal loading of active materials. Now, a strategy of burning Li foils in a CS2 vapour is presented, which leads to the formation of highly compact Li2S nanoparticles as a lithiated sulfur cathode, offering promising battery performance.

Stabilization of Li Metal Anode in DMSO-Based Electrolytes via Optimization of Salt-Solvent Coordination for Li-O 2 Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Bin; Xu, Wu; Yan, Pengfei

The conventional DMSO-based electrolyte (1 M lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in DMSO) is unstable against the Li metal anode and therefore cannot be used directly in practical Li-O2 batteries. Here, we demonstrate that a highly concentrated electrolyte based on LiTFSI in DMSO (with a molar ratio of 1:3) can greatly improve the stability of the Li metal anode against DMSO and significantly improve the cycling stability of Li-O2 batteries. This highly concentrated electrolyte contains no free DMSO solvent molecules, but only complexes of (TFSI–)a-Li+-(DMSO)b (where a + b = 4), and thus enhances their stability with Li metal anodes. In addition,more » such salt-solvent complexes have higher Gibbs activation energy barriers than the free DMSO solvent molecules, indicating improved stability of the electrolyte against the attack of superoxide radical anions. Therefore, the stability of this highly concentrated electrolyte at both Li metal anodes and carbon-based air electrodes has been greatly enhanced, resulting in improved cyclic stability of Li-O2 batteries. The fundamental stability of the electrolyte with free-solvent against the chemical and electrochemical reactions can also be used to enhance the stability of other electrochemical systems.« less

Synthesis and characterization of PVA blended LiClO4 as electrolyte material for battery Li-ion

NASA Astrophysics Data System (ADS)

Gunawan, I.; Deswita; Sugeng, B.; Sudaryanto

2017-07-01

It have been synthesized the materials for Li ion battery electrolytes, namely PVA with the addition of LiClO4 salt were varied 0, 5, 10, 15 and 20% by weight respectively. The objective of this study is to control the ionic conductivity in traditional polymer electrolytes, to improve ionic conductivity with the addition of lithium perchlorat (LiClO4). These electrolyte materials prepared by PVA powder was dissolved into distilled water and added LiClO4 salt were varied. After drying the solution, PVA sheet blended LiClO4 salt as electrolyte material for Li ion battery obtained. PVA blended LiClO4 salt crystallite form was confirmed using X-Ray Difraction (XRD) equipment. Observation of the morphology done by using Scanning Electron Microscope (SEM). While the electrical conductivity of the material is measured using LCR meter. The results of XRD pattern of LiClO4 shows intense peaks at angles 2θ = 23.2, 32.99, and 36.58°, which represent the crystalline nature of the salt. Particles morphology of the sample revealed by scanning electron microscopy are irregular in shape and agglomerated, with mean size 200-300 nm. It can be concluded that polycrystalline particles are composed of large number of crystallites. The study of conductivity by using LCR meter shows that all the graphs represent the DC and AC conductivity phenomena.

Li2.97Mg0.03VO4: High rate capability and cyclability performances anode material for rechargeable Li-ion batteries

NASA Astrophysics Data System (ADS)

Dong, Youzhong; Zhao, Yanming; Duan, He; Singh, Preetam; Kuang, Quan; Peng, Hongjian

2016-07-01

Mg-doped composite, Li2.97Mg0.03VO4, with an orthorhombic structure was prepared by a sol-gel method. The effects of the Mg doping on the structure and electrochemical performance of Li3VO4 were investigated. The X-ray diffraction pattern shows that the Mg doping does not change the crystal structure of Li3VO4. The EDS mappings indicated the fairly uniform distribution of Mg throughout the grains of Li2.97Mg0.03VO4. Electronic conductivity of Mg-doped Li3VO4 increased by two orders of magnitude compared to that of pure Li3VO4. CV and EIS measurement confirms that the Li2.97Mg0.03VO4 sample exhibits a smaller polarization and transfer resistance and a higher lithium diffusion coefficient compared with the pure Li3VO4. Due to the better electrochemical kinetics properties, Mg-doped Li3VO4 showed a significant improved performance compared to the pure Li3VO4, especially for the high rate capability. At the higher discharge/charge rate (2C), the discharge and charge capacities of 415.5 and 406.1 mAh/g have been obtained for the Li2.97Mg0.03VO4 which is more than three times higher the discharge/charge capacities of Li3VO4. The discharge and charge capacities of pure Li3VO4 are only 126.4 and 125.8 mAh/g respectively. The excellent electrochemical performance of Li2.97Mg0.03VO4 enables it as a promising anode material for rechargeable lithium-ion batteries.

Li2S/Carbon Nanocomposite Strips from a Low-Temperature Conversion of Li2SO4 as High-Performance Lithium-Sulfur Cathodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Fangmin; Noh, Hyungjun; Lee, Jin Hong

2018-03-12

Carbothermal conversion of Li2SO4 provides a cost-effective strategy to fabricate high-capacity Li2S cathodes, however, Li2S cathodes derived from Li2SO4 at high temperatures (> 800 oC), having high crystallinity and large crystal size, result in a low utilization of Li2S. Here, we report a Li2SO4/poly(vinyl alcohol)-derived Li2S/Carbon nanocomposite (Li2S@C) strips at a record low temperature of 635 oC. These Li2S@C nanocomposite strips as a cathode shows a low initial activation potential (2.63 V), a high initial discharge capacity (805 mAh g-1 Li2S) and a high cycling stability (0.2 C and 1 C). These improvedresults could be ascribed to the nano-sized Li2Smore » particles as well as their low crystallinity due to the PVA-induced carbon network and the low conversion temperature, respectively. An XPS analysis reveals that the C=C and C=O bonds derived from the carbonization of PVA can promote the conversion of Li2SO4 at the low temperature.« less

Revision of the Li13Si4 structure.

PubMed

Zeilinger, Michael; Fässler, Thomas F

2013-11-06

Besides Li17Si4, Li16.42Si4, and Li15Si4, another lithium-rich representative in the Li-Si system is the phase Li13Si4 (trideca-lithium tetra-silicide), the structure of which has been determined previously [Frank et al. (1975 ▶). Z. Naturforsch. Teil B, 30, 10-13]. A careful analysis of X-ray diffraction patterns of Li13Si4 revealed discrepancies between experimentally observed and calculated Bragg positions. Therefore, we redetermined the structure of Li13Si4 on the basis of single-crystal X-ray diffraction data. Compared to the previous structure report, decisive differences are (i) the introduction of a split position for one Li site [occupancy ratio 0.838 (7):0.162 (7)], (ii) the anisotropic refinement of atomic displacement parameters for all atoms, and (iii) a high accuracy of atom positions and unit-cell parameters. The asymmetric unit of Li13Si4 contains two Si and seven Li atoms. Except for one Li atom situated on a site with symmetry 2/m, all other atoms are on mirror planes. The structure consists of isolated Si atoms as well as Si-Si dumbbells surrounded by Li atoms. Each Si atom is either 12- or 13-coordinated. The isolated Si atoms are situated in the ab plane at z = 0 and are strictly separated from the Si-Si dumbbells at z = 0.5.

Interfacial Li-ion localization in hierarchical carbon anodes

DOE PAGES

McNutt, Nicholas W.; Rios, Orlando; Maroulas, Vasileios; ...

2016-10-24

An understanding of the nanoscale structure and energetics of carbon composites is critical for their applications in electric energy storage. Here, we study the properties of carbon anodes synthesized from low-cost renewable lignin biopolymers for use in energy storage applications such as Li-ion batteries. The anodes possess both nanoscale and mesoscale order, consisting of carbon nanocrystallites distributed within an amorphous carbon matrix. Molecular dynamics simulations of an experimentally validated model of the anode is used to elucidate the nature of Li-ion storage. We report the discovery of a novel mechanism of Li-ion storage, one in which Li+ is not intercalatedmore » between layers of carbon (as is the case in graphitic anodes), but rather is localized at the interface of crystalline carbon domains. In particular, the effects of Li-ion binding energy on the Li-Li, Li-H, and Li-C pair distribution functions are revealed, along with the effect on charge distribution. As a result, the atomic environments surrounding the Li-ions are grouped on the basis of ion energy and then convolved into archetypal structural motifs that reveal deep insight into the geometry of ion localization in disordered systems.« less

Nanotechnology in Li-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mukaibo, Hitomi

2010-06-04

This is the second of three talks on nanostructures for li-ion batteries. The talks provide an up-to-date review of the issues and challenges facing Li-ion battery research with special focus on how nanostructures/ nanotechnology are being applied to this field. Novel materials reported as prospective candidates for anode, cathode and electrolyte will be summarized. The expected role of nanostructures in improving the performance of Li-ion batteries and the actual pros and cons of using such structures in this device will be addressed. Electrochemical experiments used to study Li-ion batteries will also be discussed. This includes the introduction to the standardmore » experimental set-up and how experimental data (from charge-discharge experiments, cyclic voltammetry, impedance spectroscopy, etc) are interpreted.« less

Enhanced ionic conductivity with Li 7O 2Br 3 phase in Li 3OBr anti-perovskite solid electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Jinlong; Li, Shuai; Zhang, Yi

Cubic anti-perovskites with general formula Li 3OX (X = Cl, Br, I) were recently reported as superionic conductors with the potential for use as solid electrolytes in all-solid-state lithium ion batteries. These electrolytes are nonflammable, low-cost, and suitable for thermoplastic processing. However, the primary obstacle of its practical implementation is the relatively low ionic conductivity at room temperature. In this work, we synthesized a composite material consisting of two anti-perovskite phases, namely, cubic Li 3OBr and layered Li 7O 2Br 3, by solid state reaction routes. The results indicate that with the phase fraction of Li 7O 2Br 3 increasingmore » to 44 wt. %, the ionic conductivity increased by more than one order of magnitude compared with pure phase Li 3OBr. Formation energy calculations revealed the meta-stable nature of Li 7O 2Br 3, which supports the great difficulty in producing phase-pure Li 7O 2Br 3 at ambient pressure. Here, methods of obtaining phase-pure Li 7O 2Br 3 will continue to be explored, including both high pressure and metathesis techniques.« less

Enhanced ionic conductivity with Li 7O 2Br 3 phase in Li 3OBr anti-perovskite solid electrolyte

DOE PAGES

Zhu, Jinlong; Li, Shuai; Zhang, Yi; ...

2016-09-07

Cubic anti-perovskites with general formula Li 3OX (X = Cl, Br, I) were recently reported as superionic conductors with the potential for use as solid electrolytes in all-solid-state lithium ion batteries. These electrolytes are nonflammable, low-cost, and suitable for thermoplastic processing. However, the primary obstacle of its practical implementation is the relatively low ionic conductivity at room temperature. In this work, we synthesized a composite material consisting of two anti-perovskite phases, namely, cubic Li 3OBr and layered Li 7O 2Br 3, by solid state reaction routes. The results indicate that with the phase fraction of Li 7O 2Br 3 increasingmore » to 44 wt. %, the ionic conductivity increased by more than one order of magnitude compared with pure phase Li 3OBr. Formation energy calculations revealed the meta-stable nature of Li 7O 2Br 3, which supports the great difficulty in producing phase-pure Li 7O 2Br 3 at ambient pressure. Here, methods of obtaining phase-pure Li 7O 2Br 3 will continue to be explored, including both high pressure and metathesis techniques.« less

Concentration dependence of Li+/Na+ diffusion in manganese hexacyanoferrates

NASA Astrophysics Data System (ADS)

Takachi, Masamitsu; Fukuzumi, Yuya; Moritomo, Yutaka

2016-06-01

Manganese hexacyanoferrates (Mn-HCFs) with a jungle-gym-type structure are promising cathode materials for Li+/Na+ secondary batteries (LIBs/SIBs). Here, we investigated the diffusion constants D Li/D Na of Li+/Na+ against the Li+/Na+ concentration x Na/x Li and temperature (T) of A 1.32Mn[Fe(CN)6]0.833.6H2O (A = Li and Na). We evaluated the activation energy E\\text{a}\\text{Li}/E\\text{a}\\text{Na} of D Li/D Na against x Na/x Li. We found that E\\text{a}\\text{Na} steeply increases with x Na from 0.41 eV at x Na = 0.69 to 0.7 eV at 1.1. The increase in E\\text{a}\\text{Na} is ascribed to the occupancy effect of the Na+ site. The increase in E\\text{a}\\text{Li} is suppressed, probably because the number of Li+ sites is three times that of Na+ sites.

Influence of Li3BO3 additives on the Li+ conductivity and stability of Ca/Ta-substituted Li6.55(La2.95Ca0.05)(Zr1.5Ta0.5)O12 electrolytes

NASA Astrophysics Data System (ADS)

Zhang, L. C.; Yang, J. F.; Gao, Y. X.; Wang, X. P.; Fang, Q. F.; Chen, C. H.

2017-07-01

The cubic Ca/Ta-substituted Li6.55(La2.95Ca0.05)(Zr1.5Ta0.5)O12 (LLCZTO) electrolytes were synthesized at 800 °C with Li3BO3 as additives. The optimal amount of Li3BO3 and its influences on the microstructure, crystal structures, Li+ conductivity and the stability of the Li6.55(La2.95Ca0.05)(Zr1.5Ta0.5)O12 were studied by SEM, XRD and EIS. Among all the samples, when the molar ratio of Li3BO3 to the Li6.55(La2.95Ca0.05)(Zr1.5Ta0.5)O12 is 4:5, the highest Li+ conductivity of 1.33 × 10-4 S cm-1 at 30 °C is obtained. When the LLCZTO samples are exposed in air, the Li+ conductivity is deteriorated possibly owing to the side reactions between the LLCZTO and the H2O or CO2 in the air. The Li3BO3 addition can alleviate such deterioration of the Li+ conductivity.

LiDAR for data efficiency.

DOT National Transportation Integrated Search

2011-09-30

This report documents the AHMCT research project: LiDAR for Data Efficiency for the Washington State Department of Transportation (WSDOT). The research objective was to evaluate mobile LiDAR technology to enhance safety, determine efficiency ga...

Albert LiVecchi | NREL

Science.gov Websites

Albert LiVecchi Photo of Al Livecchi Albert LiVecchi Laboratory Program Manager- Water Power Al.Livecchi@nrel.gov | 303-384-7138 Al has been part of the Wind and Water Power Program Management Team at focuses on marine and hydrokinetic technologies. As Water Power Laboratory Program Manager, Al is

EGFR LI and Ki-67 LI are independent prognostic parameters influencing survivals of surgically treated squamous cell lung cancer patients.

PubMed

Niemiec, J; Kolodziejski, L; Dyczek, S

2005-01-01

In literature there are still opinion differences concerning the prognostic significance of epidermal growth factor receptor (EGFR) expression and proliferative potential in patients with non small cell lung cancer (NSCLC). This prompted us to study those parameters. The Ki-67 labeling index (Ki-67 LI), EGFR labeling index (EGFR LI), and mitotic index (MI) were analyzed in the group of 78 consecutive, surgically treated squamous cell lung cancer (SqCLC) patients. The expression of Ki-67 and EGFR protein was visualized on formalin fixed, paraffin embedded sections using immunohistochemistry (IHC). Mitotic index was assessed on formalin fixed, paraffin embedded sections, stained with hematoxylin and eosin using morphological criteria. Mean values of Ki-67 LI and MI were higher for G2+G3 tumors than for G1 tumors. EGFR LI was higher for G1+G2 than for G3 tumors, and for pT3 than for pT1+pT2 tumors. Patients having tumors with Ki-67 < or =28% or (EGFR LI < or =13% or EGFR LI >80%) survived significantly shorter than those having tumors with Ki-67 LI >28% or 13%< EGFR LI < or =80%. In multivariate analysis, 13%> or = EGFR LI <80% and Ki-67 LI < or =28% were independent negative prognostic parameters influencing survivals of SqCLC patients.

Evaluation of Li{sub 3}N accumulation in a fused LiCl/Li salt matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eberle, C.S.

1998-09-01

Pyrochemical conditioning of spent nuclear fuel for the purpose of final disposal is currently being demonstrated at Argonne National Laboratory (ANL), and ongoing research in this area includes the demonstration of this process on spent oxide fuel. In conjunction with this research, a pilot scale of the preprocessing stage is being designed by ANL-West to demonstrate the in situ hot cell capability of the chemical reduction process. An impurity evaluation was completed for a Li/LiCl salt matrix in the presence of spent light water reactor uranium oxide fuel. A simple analysis was performed in which the sources of impurities inmore » the salt matrix were only from the cell atmosphere. Only reactions with the lithium were considered. The levels of impurities were shown to be highly sensitive system conditions. A predominance diagram for the Li-O-N system was constructed for the device, and the general oxidation, nitridation, and combined reactions were calculated as a function of oxygen and nitrogen partial pressure. These calculations and hot cell atmosphere data were used to determine the total number and type of impurities expected in the salt matrix, and the mass rate for the device was determined.« less

White blood cell count and the incidence of hyperuricemia: insights from a community-based study.

PubMed

Liu, Jian; Shen, Pingyan; Ma, Xiaobo; Yu, Xialian; Ni, Liyan; Hao, Xu; Wang, Weiming; Chen, Nan

2018-06-23

Hyperuricemia (HUA) is a risk factor for chronic kidney disease (CKD). The relationship between HUA and white blood cell (WBC) count remains unknown. A sampling survey for CKD was conducted in Sanlin community in 2012 and 2014. CKD was defined as proteinuria in at least the microalbuminuric stage or an estimated GFR of 60 mL/(min∙1.73 m 2 ). HUA was defined as serum uric acid > 420 μmol/L in men and > 360 μmol/L in women. This study included 1024 participants. The prevalence of HUAwas 17.77%. Patients with HUA were more likely to have higher levels of WBC count, which was positively associated with HUA prevalence. This association was also observed in participants without CKD, diabetes mellitus, hyperlipidemia, or obesity. Multivariate logistic regression analysis showed that WBC count was independently associated with the risk for HUA in male and female participants. Compared with participants without HUA, inflammatory factors such as high-sensitivity C-reactive protein, tumor necrosis factor-α, and interleukin 6 increased in participants with HUA. Hence, WBC count is positively associated with HUA, and this association is independent of conventional risk factors for CKD.

Li2 B12 and Li3 B12 : Prediction of the Smallest Tubular and Cage-like Boron Structures.

PubMed

Dong, Xue; Jalife, Said; Vásquez-Espinal, Alejandro; Ravell, Estefanía; Pan, Sudip; Cabellos, José Luis; Liang, Wei-Yan; Cui, Zhong-Hua; Merino, Gabriel

2018-04-16

An intriguing structural transition from the quasi-planar form of B 12 cluster upon the interaction with lithium atoms is reported. High-level computations show that the lowest energy structures of LiB 12 , Li 2 B 12 , and Li 3 B 12 have quasi-planar (C s ), tubular (D 6d ), and cage-like (C s ) geometries, respectively. The energetic cost of distorting the B 12 quasi-planar fragment is overcompensated by an enhanced electrostatic interaction between the Li cations and the tubular or cage-like B 12 fragments, which is the main reason of such drastic structural changes, resulting in the smallest tubular (Li 2 B 12 ) and cage-like (Li 3 B 12 ) boron structures reported to date. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Burning lithium in CS2 for high-performing compact Li2 S-graphene nanocapsules for Li-S batteries

NASA Astrophysics Data System (ADS)

Tan, Guoqiang; Xu, Rui; Xing, Zhenyu; Yuan, Yifei; Lu, Jun; Wen, Jianguo; Liu, Cong; Ma, Lu; Zhan, Chun; Liu, Qi; Wu, Tianpin; Jian, Zelang; Shahbazian-Yassar, Reza; Ren, Yang; Miller, Dean J.; Curtiss, Larry A.; Ji, Xiulei; Amine, Khalil

2017-07-01

Tremendous efforts have been made to design the cathode of Li-S batteries to improve their energy density and cycling life. However, challenges remain in achieving fast electronic and ionic transport while accommodating the significant cathode volumetric change, especially for the cathode with a high practical mass loading. Here we report a cathode architecture, which is constructed by burning lithium foils in a CS2 vapour. The obtained structure features crystalline Li2S nanoparticles wrapped by few-layer graphene (Li2S@graphene nanocapsules). Because of the improvement on the volumetric efficiency for accommodating sulfur active species and electrical properties, the cathode design enables promising electrochemical performance. More notably, at a loading of 10 mgLi2S cm-2, the electrode exhibits a high reversible capacity of 1,160 mAh g-1s, namely, an area capacity of 8.1 mAh cm-2. Li2S@graphene cathode demonstrates a great potential for Li-ion batteries, where the Li2S@graphene-cathode//graphite-anode cell displays a high capacity of 730 mAh g-1s as well as stable cycle performance.

High-pressure synthesis and electrochemical behavior of layered (1-a)LiNi{sub 1-y}Al{sub y}O{sub 2}.aLi[Li{sub 1/3}Ni{sub 2/3}]O{sub 2} oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shinova, E.; Zhecheva, E.; Stoyanova, R.

Layered (1-a)LiNi{sub 1-y}Al{sub y}O{sub 2}.aLi[Li{sub 1/3}Ni{sub 2/3}]O{sub 2} oxides, 0=Li{sub 2}O{sub 2} under high pressure. The structural characterization of the layered oxides was performed using powder XRD, IR spectroscopy and EPR spectroscopy at 9.23 and 115GHz. It has been found that the high-pressure favors Al substitution for Ni in the NiO{sub 2}-layers of layered LiNiO{sub 2}. A random Al/Ni distribution in the layer was found. The incorporation of extra Li in the Ni{sub 1-y}Al{sub y}O{sub 2}-layer starts at a precursor composition Li/(Ni+Al)>1.2. While pure NiO{sub 2}-layersmore » are able to incorporate under high-pressure up to 1/3Li, the appearance of Al in the NiO{sub 2}-layers hinders Li{sup +} dissolution (Li<(1-y)/3). In addition, with increasing Al content there is a strong cationic mixing between the layers. High-frequency EPR of Ni{sup 3+} indicates that the structural interaction of LiAl{sub y}Ni{sub 1-y}O{sub 2} with Li[Li{sub 1/3}Ni{sub 2/3}]O{sub 2} proceeds via the formation of domains comprising different amount of Ni{sup 3+} ions. The use of Li{sub 1.08}Al{sub 0.09}Ni{sub 0.83}O{sub 2} as a cathode material in a lithium ion cells displays a first irreversible Li extraction at 4.8V, after which a reversible lithium insertion/extraction between 3.0 and 4.5V is observed on further cycling.« less

The Nature of Electrochemical Delithiation of Li-Mg Alloy Electrodes: Neutron Computed Tomography and Modeling of Li Diffusion and Delithiation Phenomenon

DOE PAGES

Zhang, Yuxuan; Chandran, K.S. Ravi; Jagannathan, M.; ...

2016-12-05

Li-Mg alloys are promising as positive electrodes (anodes) for Li-ion batteries due to the high Li storage capacity and the relatively lower volume change during the lithiation/delithiation process. They also present a unique opportunity to image the Li distribution through the electrode thickness at various delithiation states. In this work, spatial distributions of Li in electrochemically delithiated Li-Mg alloy electrodes have been quantitatively determined using neutron tomography. Specifically, the Li concentration profiles along thickness direction are determined. A rigorous analytical model to quantify the diffusion-controlled delithiation, accompanied by phase transition and boundary movement, has also been developed to explain themore » delithiation mechanism. The analytical modeling scheme successfully predicted the Li concentration profiles which agreed well with the experimental data. It is demonstrated that during discharge Li is removed by diffusion through the solid solution Li-Mg phases and this proceeds with β→α phase transition and the associated phase boundary movement through the thickness of the electrode. This is also accompanied by electrode thinning due to the change in molar volume during delithiation. In conclusion, following the approaches developed here, one can develop a rigorous and quantitative understanding of electrochemical delithiation in electrodes of electrochemical cells, similar to that in the present Li-Mg electrodes.« less

The Nature of Electrochemical Delithiation of Li-Mg Alloy Electrodes: Neutron Computed Tomography and Modeling of Li Diffusion and Delithiation Phenomenon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yuxuan; Chandran, K.S. Ravi; Jagannathan, M.

Li-Mg alloys are promising as positive electrodes (anodes) for Li-ion batteries due to the high Li storage capacity and the relatively lower volume change during the lithiation/delithiation process. They also present a unique opportunity to image the Li distribution through the electrode thickness at various delithiation states. In this work, spatial distributions of Li in electrochemically delithiated Li-Mg alloy electrodes have been quantitatively determined using neutron tomography. Specifically, the Li concentration profiles along thickness direction are determined. A rigorous analytical model to quantify the diffusion-controlled delithiation, accompanied by phase transition and boundary movement, has also been developed to explain themore » delithiation mechanism. The analytical modeling scheme successfully predicted the Li concentration profiles which agreed well with the experimental data. It is demonstrated that during discharge Li is removed by diffusion through the solid solution Li-Mg phases and this proceeds with β→α phase transition and the associated phase boundary movement through the thickness of the electrode. This is also accompanied by electrode thinning due to the change in molar volume during delithiation. In conclusion, following the approaches developed here, one can develop a rigorous and quantitative understanding of electrochemical delithiation in electrodes of electrochemical cells, similar to that in the present Li-Mg electrodes.« less

Developing New Electrolytes for Advanced Li-ion Batteries

NASA Astrophysics Data System (ADS)

McOwen, Dennis Wayne

The use of renewable energy sources is on the rise, as new energy generating technologies continue to become more efficient and economical. Furthermore, the advantages of an energy infrastructure which relies more on sustainable and renewable energy sources are becoming increasingly apparent. The most readily available of these renewable energy sources, wind and solar energy in particular, are naturally intermittent. Thus, to enable the continued expansion and widespread adoption of renewable energy generating technology, a cost-effective energy storage system is essential. Additionally, the market for electric/hybrid electric vehicles, which both require efficient energy storage, continues to grow as more consumers seek to reduce their consumption of gasoline. These vehicles, however, remain quite expensive, due primarily to costs associated with storing the electrical energy. High-voltage and thermally stable Li-ion battery technology is a promising solution for both grid-level and electric vehicle energy storage. Current limitations in materials, however, limit the energy density and safe operating temperature window of the battery. Specifically, the state-of-the-art electrolyte used in Li-ion batteries is not compatible with recently developed high-voltage positive electrodes, which are one of the most effectual ways of increasing the energy density. The electrolyte is also thermally unstable above 50 °C, and prone to thermal runaway reaction if exposed to prolonged heating. The lithium salt used in such electrolytes, LiPF6, is a primary contributor to both of these issues. Unfortunately, an improved lithium salt which meets the myriad property requirements for Li-ion battery electrolytes has eluded researchers for decades. In this study, a renewed effort to find such a lithium salt was begun, using a recently developed methodology to rapidly screen for desirable properties. Four new lithium salts and one relatively new but uncharacterized lithium salt were

Aligned Li+ Tunnels in Core-Shell Li(NixMnyCoz)O2@LiFePO4 Enhances Its High Voltage Cycling Stability as Li-ion Battery Cathode.

PubMed

Wu, Zhongzhen; Ji, Shunping; Liu, Tongchao; Duan, Yandong; Xiao, Shu; Lin, Yuan; Xu, Kang; Pan, Feng

2016-10-12

Layered transition-metal oxides (Li[Ni x Mn y Co z ]O 2 , NMC, or NMCxyz) due to their poor stability when cycled at a high operating voltage (>4.5 V) have limited their practical applications in industry. Earlier researches have identified Mn(II)-dissolution and some parasitic reactions between NMC surface and electrolyte, especially when NMC is charged to a high potential, as primarily factors responsible for the fading. In our previous work, we have achieved a capacity of NMC active material close to theoretical value and optimized its cycling performance by a depolarized carbon nanotubes (CNTs) network and an unique "pre-lithiation process" that generates an in situ organic coating (∼40 nm) to prevent Mn(II) dissolution and minimize the parasitic reactions. Unfortunately, this organic coating is not durable enough during a long-term cycling when the cathode operates at a high potential (>4.5 V). This work attempts to improve the surface protection of the NMC532 particles by applying an active inorganic coating consisting of nanosized- and crystal-orientated LiFePO 4 (LFP) (about 50 nm, exposed (010) face) to generate a core-shell nanostructure of Li(Ni x Mn y Co z )O 2 @LiFePO 4 . Transmission electron microscopy (TEM) and etching X-ray photoelectron spectroscopy have confirmed an intimate contact coating (about 50 nm) between the original structure of NMC and LFP single-particle with atomic interdiffusion at the core-shell interface, and an array of interconnected aligned Li + tunnels are observed at the interface by cross-sectional high-resolution TEM, which were formed by ball-milling and then strictly controlling the temperature below 100 °C. Batteries based on this modified NMC cathode material show a high reversible capacity when cycled between 3.0 and 4.6 V during a long-term cycling.

Electrolytes in Support of 5V Li-ion Batteries

DTIC Science & Technology

2010-12-16

candidates LiCoPO4, LiNi0.5Mn1.5O4, Li2FeCoPO4 etc, projected to deliver 15~40% more energy than state-of-art LiFePO4 The additive invented by SEDD is...battery pack for HEV as example: 300 V hybrid electric system • requires at least 100 LiFePO4 Li ion cells in series • power electronics, protection...FOR PUBLIC RELEASE The “5V” Li ion cathode needs a “5V” electrolyte • Potentially up to 40% greater energy density than LiFePO4 • Higher voltage at

Optically pumped cerium-doped LiSrAlF.sub.6 and LiCaAlF.sub.6

DOEpatents

Marshall, Christopher D.; Payne, Stephen A.; Krupke, William F.

1996-01-01

Ce.sup.3+ -doped LiSrAlF.sub.6 crystals are pumped by ultraviolet light which is polarized along the c axis of the crystals to effectively energize the laser system. In one embodiment, the polarized fourth harmonic light output from a conventional Nd:YAG laser operating at 266 nm is arranged to pump Ce:LiSrAlF.sub.6 with the pump light polarized along the c axis of the crystal. The Ce:LiSrAlF.sub.6 crystal may be placed in a laser cavity for generating tunable coherent ultraviolet radiation in the range of 280-320 nm. Additionally, Ce-doped crystals possessing the LiSrAlF.sub.6 type of chemical formula, e.g. Ce-doped LiCaAlF.sub.6 and LiSrGaF.sub.6, can be used. Alternative pump sources include an ultraviolet-capable krypton or argon laser, or ultraviolet emitting flashlamps. The polarization of the pump light will impact operation. The laser system will operate efficiently when light in the 280-320 nm gain region is injected or recirculated in the system such that the beam is also polarized along the c axis of the crystal. The Ce:LiSrAlF.sub.6 laser system can be configured to generate ultrashort pulses, and it may be used to pump other devices, such as an optical parametric oscillator.

Revision of the Li13Si4 structure

PubMed Central

Zeilinger, Michael; Fässler, Thomas F.

2013-01-01

Besides Li17Si4, Li16.42Si4, and Li15Si4, another lithium-rich representative in the Li–Si system is the phase Li13Si4 (trideca­lithium tetra­silicide), the structure of which has been determined previously [Frank et al. (1975 ▶). Z. Naturforsch. Teil B, 30, 10–13]. A careful analysis of X-ray diffraction patterns of Li13Si4 revealed discrepancies between experimentally observed and calculated Bragg positions. Therefore, we redetermined the structure of Li13Si4 on the basis of single-crystal X-ray diffraction data. Compared to the previous structure report, decisive differences are (i) the introduction of a split position for one Li site [occupancy ratio 0.838 (7):0.162 (7)], (ii) the anisotropic refinement of atomic displacement parameters for all atoms, and (iii) a high accuracy of atom positions and unit-cell parameters. The asymmetric unit of Li13Si4 contains two Si and seven Li atoms. Except for one Li atom situated on a site with symmetry 2/m, all other atoms are on mirror planes. The structure consists of isolated Si atoms as well as Si–Si dumbbells surrounded by Li atoms. Each Si atom is either 12- or 13-coordinated. The isolated Si atoms are situated in the ab plane at z = 0 and are strictly separated from the Si–Si dumbbells at z = 0.5. PMID:24454148

Structural and thermodynamic similarities of phases in the Li-Tt (Tt = Si, Ge) systems: redetermination of the lithium-rich side of the Li-Ge phase diagram and crystal structures of Li17Si4.0-xGex for x = 2.3, 3.1, 3.5, and 4 as well as Li4.1Ge.

PubMed

Zeilinger, Michael; Fässler, Thomas F

2014-10-28

A reinvestigation of the lithium-rich section of the Li-Ge phase diagram reveals the existence of two new phases, Li17Ge4 and Li4.10Ge (Li16.38Ge4). Their structures are determined by X-ray diffraction experiments of large single crystals obtained from equilibrated melts with compositions Li95Ge5 and Li85Ge15. Excess melt is subsequently removed through isothermal centrifugation at 400 °C and 530 °C, respectively. Li17Ge4 crystallizes in the space group F4[combining macron]3m (a = 18.8521(3) Å, V = 6700.1(2) Å(3), Z = 20, T = 298 K) and Li4.10Ge (Li16.38Ge4) in Cmcm (a = 4.5511(2) Å, b = 22.0862(7) Å, c = 13.2751(4) Å, V = 1334.37(8) Å(3), Z = 16, T = 123 K). Both phases are isotypic with their Si counterparts and are further representative of the Li17Pb4 and Li4.11Si structure types. Additionally, the solid solutions Li17Si4-xGex follows Vegard's law. A comparison of the GeLin coordination polyhedra shows that isolated Ge atoms are 13- and 14-coordinated in Li17Ge4, whereas in Li16.38Ge4 the Ge atoms possess coordination numbers 12 and 13. Regarding the thermodynamic stability, Li16.38Ge4 is assigned a high-temperature phase existing between ∼400 °C and 627 °C, whereas Li17Ge4 decomposes peritectically at 520-522 °C. Additionally, the decomposition of Li16.38Ge4 below ∼400 °C was found to be very sluggish. These findings are manifested by differential scanning calorimetry, long-term annealing experiments and the results from melt equilibration experiments. Interestingly, the thermodynamic properties of the lithium-rich tetrelides Li17Tt4 and Li4.1Tt (Li16.4Tt4) are very similar (Tt = Si, Ge). Besides Li15Tt4, Li14Tt6, Li12Tt7, and LiTt, the title compounds are further examples of isotypic tetrelides in the systems Li-Tt.

Irradiation behavior of LiAlO 2 and Li 2ZrO 3 ceramics in the ALICE 3 experiment

NASA Astrophysics Data System (ADS)

Rasneur, B.; Thevenot, G.; Bouilloux, Y.

1992-09-01

Within the framework of the investigation of ceramic breeders for the DEMO relevant solid blankets developed in Europe, the ALICE 3 experiment was foreseen to study the irradiation behavior of the ceramics. The irradiation was performed in the core of the OSIRIS reactor for 46 FPD (full power days) at 400°C and 600°C. The three ceramics in the configuration contemplated in the BIT and BOT concepts were tested, i.e. LiAlO 2 and Li 2ZrO 3 pellets, Li 4SiO 4 and Li 2ZrO 3 pebbles, respectively. In this paper are reported the results of the post-irradiation examination carried out at CEA on CEA Li 2ZrO 3 and LiAlO 2 specimens: dimensions, X-ray diffraction, ultimate bending strength, diametral compressive strength and residual tritium.

Searching for “LiCrIIPO4”

NASA Astrophysics Data System (ADS)

Mosymow, E.; Glaum, R.; Kremer, R. K.

2014-10-01

The two new phosphates LiCrII4(PO4)3 and Li5CrII2CrIII(PO4)4 are discovered as equilibrium phases (ϑ=800 °C) in the quarternary system Li/Cr/P/O. Their crystal structures have been determined from single-crystal X-ray diffraction data {LiCrII4(PO4)3: violet-blue, Pnma (no. 62), Z=4, a=6.175(1) Å, b=14.316(3) Å, c=10.277(2) Å, 100 parameters, R1=0.028, wR2=0.08, 2060 unique reflections with Fo>4σ(Fo); Li5CrII2CrIII(PO4)4: greyish-green, P1bar (no. 2), Z=1, a=4.9379(7) Å, b=7.917(2) Å, c=8.426(2) Å, α=109.98(2)°, β=90.71(1)°, γ=104.91(1)°, 131 parameters, R1=0.022, wR2=0.067, 1594 unique reflections with Fo>4σ(Fo)}. Li5CrII2CrIII(PO4)4 adopts an hitherto unknown structure type. The crystal structure of LiCrII4(PO4)3 is isotypic to that of NaCdII4(PO4)3 and related to that of the mineral silicocarnotite Ca5(PO4)2(SiO4). Significant disorder between Li+ and Cr2+ is observed for both crystal structures. The oxidation states assigned to chromium in these two phosphates are in agreement with UV/vis/NIR absorption spectra and magnetic susceptibility data recorded for both compounds. Instead of “LiCrIIPO4” mixtures of LiCrII4(PO4)3, Li5CrII2CrIII(PO4)4, Cr2O3, and CrP are observed at equilibrium. Instead of “Li2CrIIP2O7” four-phase mixtures consisting of Li9CrIII3(P2O7)3(PO4)2, Li3CrIII2(PO4)3, LiCrP2O7, and CrP were obtained.

Optical quasi-soliton solutions for higher-order nonlinear Schrödinger equation with variable coefficients

NASA Astrophysics Data System (ADS)

Zhang, Jiefang; Yang, Qin; Dai, Chaoqing

2005-04-01

Optical quasi-soliton solutions for higher-order nonlinear Schrödinger equation (HNLS) with variable coefficients are considered. Based on the extended tanh-function method, we successfully obtained bright and dark quasi-soliton solutions under certain parametric conditions. We conclude that the parameter k(z) is unnecessary to be zero compared with [R. Yang et al., Opt. Commun. 242 (2004) 285]. Furthermore, we choose appropriate optical fiber parameters D2(z) and D3(z) to control the velocity of quasi-soliton and time shift, and discuss the evolution behavior of the special quasi-soliton. For D3(z) = α(z) = f(z) = 0, that is to say, under the absence of the higher order terms, we give same results as early reported in [R.Y. Hao, L. Li, Z.H. Li, W.R. Xue, G.S. Zhou, Opt. Commun. 236 (2004) 79]. As discussed examples, we also analyze three optical systems with real physical significance and obtain results which can be recovered in earlier papers.

Solution based synthesis of mixed-phase materials in the Li2TiO3-Li4SiO4 system

NASA Astrophysics Data System (ADS)

Hanaor, Dorian A. H.; Kolb, Matthias H. H.; Gan, Yixiang; Kamlah, Marc; Knitter, Regina

2015-01-01

As candidate tritium breeder materials for use in the ITER helium cooled pebble bed, ceramic multiphasic compounds lying in the region of the quasi-binary lithium metatitanate-lithium orthosilicate system may exhibit mechanical and physical advantages relative to single phase materials. Here we present an organometallic solution-based synthesis procedure for the low-temperature fabrication of compounds in the Li2TiO3-Li4SiO4 region and investigate phase stability and transformations through temperature varied X-ray diffraction and scanning calorimetry. Results demonstrate that the metatitanate and metasilicate phases Li2TiO3 and Li2SiO3 readily crystallise in nanocrystalline form at temperatures below 180 °C. Lithium deficiency in the region of 5% results from Li sublimation from Li4SiO4 and/or from excess Li incorporation in the metatitanate phase and brings about a stoichiometry shift, with product compounds exhibiting mixed lithium orthosilicate/metasilicate content towards the Si rich region and predominantly Li2TiO3 content towards the Ti rich region. Above 1150 °C the transformation of monoclinic to cubic γ-Li2TiO3 disordered solid-solution occurs while the melting of silicate phases indicates a likely monotectic type system with a solidus line in the region 1050-1100 °C. Synthesis procedures involving a lithium chloride precursor are not likely to be a viable option for breeder pebble synthesis as this route was found to yield materials with a more significant Li-deficiency exhibiting the crystallisation of the Li2TiSiO5 phase at intermediate compositions.

6Li in metal-poor halo stars: real or spurious?

NASA Astrophysics Data System (ADS)

Steffen, M.; Cayrel, R.; Bonifacio, P.; Ludwig, H.-G.; Caffau, E.

2010-03-01

The presence of convective motions in the atmospheres of metal-poor halo stars leads to systematic asymmetries of the emergent spectral line profiles. Since such line asymmetries are very small, they can be safely ignored for standard spectroscopic abundance analysis. However, when it comes to the determination of the 6Li/7Li isotopic ratio, q(Li)=n(6Li)/n(7Li), the intrinsic asymmetry of the 7Li line must be taken into account, because its signature is essentially indistinguishable from the presence of a weak 6Li blend in the red wing of the 7Li line. In this contribution we quantity the error of the inferred 6Li/7Li isotopic ratio that arises if the convective line asymmetry is ignored in the fitting of the λ6707 Å lithium blend. Our conclusion is that 6Li/7Li ratios derived by Asplund et al. (2006), using symmetric line profiles, must be reduced by typically Δq(Li) ≈ 0.015. This diminishes the number of certain 6Li detections from 9 to 4 stars or less, casting some doubt on the existence of a 6Li plateau.

Li+-Permeable Film on Lithium Anode for Lithium Sulfur Battery.

PubMed

Yang, Yan-Bo; Liu, Yun-Xia; Song, Zhiping; Zhou, Yun-Hong; Zhan, Hui

2017-11-08

Lithium-sulfur (Li-S) battery is an important candidate for next-generation energy storage. However, the reaction between polysulfide and lithium (Li) anode brings poor cycling stability, low Coulombic efficiency, and Li corrosion. Herein, we report a Li protection technology. Li metal was treated in crown ether containing electrolyte, and thus, treated Li was further used as the anode in Li-S cell. Due to the coordination between Li + and crown ether, a Li + -permeable film can be formed on Li, and the film is proved to be able to block the detrimental reaction between Li anode and polysulfide. By using the Li anode pretreated in 2 wt % B15C5-containing electrolyte, Li-S cell exhibits significantly improved cycling stability, such as∼900 mAh g -1 after 100 cycles, and high Coulombic efficiency of>93%. In addition, such effect is also notable when high S loading condition is applied.

Fast neutron measurements with 7Li and 6Li enriched CLYC scintillators

NASA Astrophysics Data System (ADS)

Giaz, A.; Blasi, N.; Boiano, C.; Brambilla, S.; Camera, F.; Cattadori, C.; Ceruti, S.; Gramegna, F.; Marchi, T.; Mattei, I.; Mentana, A.; Million, B.; Pellegri, L.; Rebai, M.; Riboldi, S.; Salamida, F.; Tardocchi, M.

2016-07-01

The recently developed Cs2LiYCl6:Ce (CLYC) crystals are interesting scintillation detectors not only for their gamma energy resolution (<5% at 662 keV) but also for their capability to identify and measure the energy of both gamma rays and fast/thermal neutrons. The thermal neutrons were detected by the 6Li(n,α)t reaction while for the fast neutrons the 35Cl(n,p)35S and 35Cl(n,α)32P neutron-capture reactions were exploited. The energy of the outgoing proton or α particle scales linearly with the incident neutron energy. The kinetic energy of the fast neutrons can be measured using both the Time Of Flight (TOF) technique and using the CLYC energy signal. In this work, the response to monochromatic fast neutrons (1.9-3.8 MeV) of two CLYC 1″×1″ crystals was measured using both the TOF and the energy signal. The observables were combined to identify fast neutrons, to subtract the thermal neutron background and to identify different fast neutron-capture reactions on 35Cl, in other words to understand if the detected particle is an α or a proton. We performed a dedicated measurement at the CN accelerator facility of the INFN Legnaro National Laboratories (Italy), where the fast neutrons were produced by impinging a proton beam (4.5, 5.0 and 5.5 MeV) on a 7LiF target. We tested a CLYC detector 6Li-enriched at about 95%, which is ideal for thermal neutron measurements, in parallel with another CLYC detector 7Li-enriched at more than 99%, which is suitable for fast neutron measurements.

Laboratory submillimeter transition frequencies of Li-7H and Li-6H. [used for abundance investigations in red giant stars

NASA Technical Reports Server (NTRS)

Plummer, G. M.; Herbst, E.; De Lucia, F. C.

1984-01-01

The fundamental (J = 1 - 0) rotational transition frequencies of Li-7H and Li-6H in their ground (v = 0) vibrational states and of Li-7H in its first excited (v = 1) vibrational state have been measured in the laboratory. Use of these transition frequencies should permit astronomical investigations of LiH abundances in red giant stars of high lithium abundance.

Laser performance of in-band pumped Er : LiYF4 and Er : LiLuF4 crystals

NASA Astrophysics Data System (ADS)

Gorbachenya, K. N.; Kurilchik, S. V.; Kisel, V. E.; Yasukevich, A. S.; Kuleshov, N. V.; Nizamutdinov, A. S.; Korableva, S. L.; Semashko, V. V.

2016-02-01

Spectroscopic properties of Er : LiLuF4 and Er : LiYF4 crystals in the spectral region near 1.5 μm and the lasing characteristics of these crystals under in-band pumping at a wavelength of 1522 nm are studied. With the Er : LiLuF4 crystal, the maximum slope efficiency with respect to the absorbed pump power was 44% at a wavelength of 1609 nm. Continuous-wave operation of an inband pumped Er : LiYF4 laser is obtained for the first time. The output power at a wavelength of 1606 nm was 58 mW with a slope efficiency of 21%.

Structure evolution and thermal stability of high-energy density Li-ion battery cathode Li 2VO 2F

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiaoya; Huang, Yiqing; Ji, Dongsheng

Lithium-ion batteries (LIBs) provide high-energy-density electrochemical energy storage, which plays a central role in advancing technologies ranging from portable electronics to electric vehicles (EVs). However, a demand for lighter, more compact devices and for extended range EVs continues to fuel the need for higher energy density storage systems. Li 2VO 2F, which is synthesized in its lithiated state, allows two-electron transfer per formula during the electrochemical reaction providing a high theoretical capacity of 462 mAh/g. Herein, the synthesis and electrochemical performance of Li 2VO 2F are optimized. The thermal stability of Li 2VO 2F, which is related to the safetymore » of a battery is studied by thermal gravimetric analysis. The structure and vanadium oxidation state evolution along Li cycling are studied by ex-situ X-ray diffraction and absorption techniques. It is shown that the rock-salt structure of pristine Li 2VO 2F is stable up to at least 250°C, and is preserved upon Li cycling, which proceeds by the solid-solution mechanism. However, not all Li can be removed from the structure upon charge to 4.5 V, limiting the experimentally obtained capacity.« less

Structure evolution and thermal stability of high-energy density Li-ion battery cathode Li 2VO 2F

DOE PAGES

Wang, Xiaoya; Huang, Yiqing; Ji, Dongsheng; ...

2017-05-24

Lithium-ion batteries (LIBs) provide high-energy-density electrochemical energy storage, which plays a central role in advancing technologies ranging from portable electronics to electric vehicles (EVs). However, a demand for lighter, more compact devices and for extended range EVs continues to fuel the need for higher energy density storage systems. Li 2VO 2F, which is synthesized in its lithiated state, allows two-electron transfer per formula during the electrochemical reaction providing a high theoretical capacity of 462 mAh/g. Herein, the synthesis and electrochemical performance of Li 2VO 2F are optimized. The thermal stability of Li 2VO 2F, which is related to the safetymore » of a battery is studied by thermal gravimetric analysis. The structure and vanadium oxidation state evolution along Li cycling are studied by ex-situ X-ray diffraction and absorption techniques. It is shown that the rock-salt structure of pristine Li 2VO 2F is stable up to at least 250°C, and is preserved upon Li cycling, which proceeds by the solid-solution mechanism. However, not all Li can be removed from the structure upon charge to 4.5 V, limiting the experimentally obtained capacity.« less

Administration of Lactobacillus salivarius LI01 or Pediococcus pentosaceus LI05 improves acute liver injury induced by D-galactosamine in rats.

PubMed

Lv, Long-Xian; Hu, Xin-Jun; Qian, Gui-Rong; Zhang, Hua; Lu, Hai-Feng; Zheng, Bei-Wen; Jiang, Li; Li, Lan-Juan

2014-06-01

This work investigated the effect of the intragastric administration of five lactic acid bacteria from healthy people on acute liver failure in rats. Sprague-Dawley rats were given intragastric supplements of Lactobacillus salivarius LI01, Lactobacillus salivarius LI02, Lactobacillus paracasei LI03, Lactobacillus plantarum LI04, or Pediococcus pentosaceus LI05 for 8 days. Acute liver injury was induced on the eighth day by intraperitoneal injection of 1.1 g/kg body weight D-galactosamine (D-GalN). After 24 h, samples were collected to determine the level of liver enzymes, liver function, histology of the terminal ileum and liver, serum levels of inflammatory cytokines, bacterial translocation, and composition of the gut microbiome. The results indicated that pretreatment with L. salivarius LI01 or P. pentosaceus LI05 significantly reduced elevated alanine aminotransferase and aspartate aminotransferase levels, prevented the increase in total bilirubin, reduced the histological abnormalities of both the liver and the terminal ileum, decreased bacterial translocation, increased the serum level of interleukin 10 and/or interferon-γ, and resulted in a cecal microbiome that differed from that of the liver injury control. Pretreatment with L. plantarum LI04 or L. salivarius LI02 demonstrated no significant effects during this process, and pretreatment with L. paracasei LI03 aggravated liver injury. To the best of our knowledge, the effects of the three species-L. paracasei, L. salivarius, and P. pentosaceus-on D-GalN-induced liver injury have not been previously studied. The excellent characteristics of L. salivarius LI01 and P. pentosaceus LI05 enable them to serve as potential probiotics in the prevention or treatment of acute liver failure.

Electrical conductivity in Li2O2 and its role in determining capacity limitations in non-aqueous Li-O2 batteries

NASA Astrophysics Data System (ADS)

Viswanathan, V.; Thygesen, K. S.; Hummelshøj, J. S.; Nørskov, J. K.; Girishkumar, G.; McCloskey, B. D.; Luntz, A. C.

2011-12-01

Non-aqueous Li-air or Li-O2 cells show considerable promise as a very high energy density battery couple. Such cells, however, show sudden death at capacities far below their theoretical capacity and this, among other problems, limits their practicality. In this paper, we show that this sudden death arises from limited charge transport through the growing Li2O2 film to the Li2O2-electrolyte interface, and this limitation defines a critical film thickness, above which it is not possible to support electrochemistry at the Li2O2-electrolyte interface. We report both electrochemical experiments using a reversible internal redox couple and a first principles metal-insulator-metal charge transport model to probe the electrical conductivity through Li2O2 films produced during Li-O2 discharge. Both experiment and theory show a "sudden death" in charge transport when film thickness is ˜5 to 10 nm. The theoretical model shows that this occurs when the tunneling current through the film can no longer support the electrochemical current. Thus, engineering charge transport through Li2O2 is a serious challenge if Li-O2 batteries are ever to reach their potential.

Investigation of the Decomposition Mechanism of Lithium Bis(oxalate)borate (LiBOB) Salt in the Electrolyte of an Aprotic Li-O 2 Battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lau, Kah Chun; Lu, Jun; Low, John

2014-03-13

The stability of the lithium bis(oxalate) borate (LiBOB) salt against lithium peroxide (Li2O2) in an aprotic Li-O2 cell is investigated. From theoretical and experimental findings, we find that the chemical decomposition of LiBOB in electrolytes leads to the formation lithium oxalate during discharge of a Li-O2 cell. According to DFT calculations, the formation of lithium oxalate as the reaction product is exothermic, and therefore is thermodynamically feasible. This reaction seems to be independent of solvents used in the Li-O2 cell, and therefore LiBOB is probably not suitable to be used as the salt in Li-O2 cell electrolytes.

Evolution of the Li-Yu Lake at Eastern Taiwan: Evidences from Magnetic Proxies and Pollen Analysis

NASA Astrophysics Data System (ADS)

Lee, T.; Wang, L.; Chen, S.

2008-12-01

The Li-Yu Lake located at Hua-Lien County of eastern Taiwan seems to be originally a river and was trapped by a landslide to form a lake after. To investigate the truth, a lacustrine sediment core of about 8 meters was raised from the lake and magnetic proxies and pollen analysis were employed to analyze it. Based on the C- 14 dating, this core provides the information for the last 7000 years Magnetic proxies point out that the records could be clearly distinguished into two parts from the depth of about 2.6 meters : the deeper part dominates very coarse grained with higher oxidized magnetic minerals and vice versa at the shallower part. This boundary corresponds an ages of about 2300 yrB.P. Pollen analysis reveals that no pollen could be found at the depths below 2.8 meters; only aquatic plant pollens, such as Poaceae, Cyperaceae and Mynophyllum, were found at the depth between 2.8-2.5 meters; tree and shrub pollens began to appear at about 2.5 m in depth. These results proposed that sediments below 2.8 m (before 2400 yrBP) might be a river deposit; the river was blocked at its northern end to form a lake between 2300-2400 yrBP in consideration of the topography, and regular lake deposits occurred after 2300 yrBP. Furthermore, magnetic proxies were found to have a clear change during the age interval of about 900-600 yrBP. Pollen patterns also support this point. It is proposed that the river piracy might have happened at the southern area of the lake at this time. The literatures recording the human activity in this area seem to support this point of view.

Complete Decomposition of Li2CO3 in Li-O2 Batteries Using Ir/B4C as Noncarbon-Based Oxygen Electrode.

PubMed

Song, Shidong; Xu, Wu; Zheng, Jianming; Luo, Langli; Engelhard, Mark H; Bowden, Mark E; Liu, Bin; Wang, Chong-Min; Zhang, Ji-Guang

2017-03-08

Instability of carbon-based oxygen electrodes and incomplete decomposition of Li 2 CO 3 during charge process are critical barriers for rechargeable Li-O 2 batteries. Here we report the complete decomposition of Li 2 CO 3 in Li-O 2 batteries using the ultrafine iridium-decorated boron carbide (Ir/B 4 C) nanocomposite as a noncarbon based oxygen electrode. The systematic investigation on charging the Li 2 CO 3 preloaded Ir/B 4 C electrode in an ether-based electrolyte demonstrates that the Ir/B 4 C electrode can decompose Li 2 CO 3 with an efficiency close to 100% at a voltage below 4.37 V. In contrast, the bare B 4 C without Ir electrocatalyst can only decompose 4.7% of the preloaded Li 2 CO 3 . Theoretical analysis indicates that the high efficiency decomposition of Li 2 CO 3 can be attributed to the synergistic effects of Ir and B 4 C. Ir has a high affinity for oxygen species, which could lower the energy barrier for electrochemical oxidation of Li 2 CO 3 . B 4 C exhibits much higher chemical and electrochemical stability than carbon-based electrodes and high catalytic activity for Li-O 2 reactions. A Li-O 2 battery using Ir/B 4 C as the oxygen electrode material shows highly enhanced cycling stability than those using the bare B 4 C oxygen electrode. Further development of these stable oxygen-electrodes could accelerate practical applications of Li-O 2 batteries.

Nanostructural evolution and behavior of H and Li in ion-implanted γ-LiAlO 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Weilin; Zhang, Jiandong; Edwards, Danny J.

In-situ He+ ion irradiation is performed under a helium ion microscope to study nanostructural evolution in polycrystalline gamma-LiAlO2 pellets. Various locations within a grain, across grain boundaries and at a cavity are selected. The results exhibit He bubble formation, grain-boundary cracking, nanoparticle agglomeration, increasing surface brightness with dose, and material loss from the surface. Similar brightening effects at grain boundaries are also observed under a scanning electron microscope. Li diffusion and loss from polycrystalline gamma-LiAlO2 is faster than its monocrystalline counterpart during H2+ ion implantation at elevated temperatures. There is also more significant H diffusion and release from polycrystalline pelletsmore » during thermal annealing of 300 K implanted samples. Grain boundaries and cavities could provide a faster pathway for H and Li diffusion. H release is slightly faster from the 573 K implanted monocrystalline gamma-LiAlO2 during annealing at 773 K. Metal hydrides could be formed preferentially along the grain boundaries to immobilize hydrogen.« less

LiNbO3 Cylinder Fiber

NASA Technical Reports Server (NTRS)

2004-01-01

We have successfully fabricate optical fiber with a thin layer of LiNbO3 at the boundary of the glass core and dear glass cladding. The construction of this fiber is based on our successful Semiconductor Cylinder Fibers (SCF). A schematic representation of a LiNbO3 Cylinder Fiber is shown. These fibers can be used as light modulators, sonar detectors and in other applications. The core diameter of the fiber is sufficiently small compared to the light wavelength and the indices of refraction of the core and cladding glasses are sufficiently close in value so that there is sufficient light at the core cladding boundary to interact with the LiNbO3 layer. This fiber functions best when just a single light mode propagates through the fiber. The idea for a LiNbO3 Cylinder Fiber came from Dr. Tracee Jamison of NASA. The optical properties of LiNbO3 can be changed with strain or the application of an electric field. Thus these fibers can be used as acoustic sensors as for example in a sonar. They can also be used as electric field operated light modulators. However, for this application the fibers would be made with a cross section in the form of a 'D'. The core with its surrounding LiNbO, layer would be close to the flat portion of the 'D' shaped fiber. Two metal contacts would be deposited on the flat portion of the fiber on either side of the core. A voltage applied across these contacts will result in an electric field in the core region that can be used for modulating the optical properties of the LiNbO, layer. To our knowledge this is the first ever LiNbO, Cylinder Fiber made.

LiNbO3 Cylinder Fiber

NASA Technical Reports Server (NTRS)

Kornreich, Philip

2004-01-01

We have successfully fabricate optical fiber with a thin layer of LiNbO3 at the boundary of the glass core and clear glass cladding. The construction of this fiber is based on our successful Semiconductor Cylinder Fibers (SCF). A schematic representation of a LiN bo, Cylinder Fiber. These fibers can be used as light modulators, sonar detectors and in other applications. The core diameter of the fiber is sufficiently small compared to the light wavelength and the indices of refraction of the core and cladding glasses are sufficiently close in value so that there is sufficient light at the core cladding boundary to interact with the LiNbO3 layer. This fiber functions best when just a single light mode propagates through the fiber. The idea for a LiNbO3 Cylinder Fiber came from Dr. Tracee Jamison of NASA. The optical properties of LiNbO3 can be changed with strain or the application of an electric field. Thus these fibers can be used as acoustic sensors as for example in a sonar. They can also be used as electric field operated light modulators. However, for this application the fibers would be made with a cross section in the form of a "D". The core with its surrounding LiNbO, layer would be close to the flat portion of the "D" shaped fiber. Two metal contacts would be deposited on the flat portion of the fiber on either side of the core. A voltage applied across these contacts will result in an electric field in the core region that can be used for modulating the optical properties of the LiNbO3 layer. To our knowledge this is the first ever LiNbO3 Cylinder Fiber made.

Investigations of the electronic and magnetic properties of newly (001) surface LiCrS and LiCrSe half-Heusler compounds

NASA Astrophysics Data System (ADS)

Hussain, Moaid K.

2018-04-01

We analyzed the electronic and magnetic properties of newly (001) surface LiCrS and LiCrSe half-Heusler compounds with the C1b structure, based on calculations of the first principles. We examine the influences of (001) surface and correlation interactions on the structural properties and electricity and magnetism of the bulk and surface (001) LiCrS and LiCrSe half-Heusler compounds with two ideal terminations named Cr-S and li-li and Cr-Se and li-term terminated (001) surfaces, respectively. We noticed that the half-metallicity assured in the bulk is kept at the Cr-S and Cr-Se terminations, with a total spin polarization equal to 100%, with a wide range in the energy gap, and the magnetic moments calculated for both terminations were found to be equal to 29 µB/f.u., which have a great scientifics in varied application. For the li-li and li-term terminations, we noticed that the half-metallicity is destroy with a total spin polarization equal to 84 and 67%, respectively, with a magnetic moment of 25.5 µB/f.u. The calculated magnetic moment of all terminations was found of all the subsurface is close to that of the bulk system and this makes these compounds of maximum benefit in the pilot applications of spintronic systems.

Optically pumped cerium-doped LiSrAlF{sub 6} and LiCaAlF{sub 6}

DOEpatents

Marshall, C.D.; Payne, S.A.; Krupke, W.F.

1996-05-14

Ce{sup 3+}-doped LiSrAlF{sub 6} crystals are pumped by ultraviolet light which is polarized along the c axis of the crystals to effectively energize the laser system. In one embodiment, the polarized fourth harmonic light output from a conventional Nd:YAG laser operating at 266 nm is arranged to pump Ce:LiSrAlF{sub 6} with the pump light polarized along the c axis of the crystal. The Ce:LiSrAlF{sub 6} crystal may be placed in a laser cavity for generating tunable coherent ultraviolet radiation in the range of 280-320 nm. Additionally, Ce-doped crystals possessing the LiSrAlF{sub 6} type of chemical formula, e.g. Ce-doped LiCaAlF{sub 6} and LiSrGaF{sub 6}, can be used. Alternative pump sources include an ultraviolet-capable krypton or argon laser, or ultraviolet emitting flashlamps. The polarization of the pump light will impact operation. The laser system will operate efficiently when light in the 280-320 nm gain region is injected or recirculated in the system such that the beam is also polarized along the c axis of the crystal. The Ce:LiSrAlF{sub 6} laser system can be configured to generate ultrashort pulses, and it may be used to pump other devices, such as an optical parametric oscillator. 10 figs.

Uniform Li deposition regulated via three-dimensional polyvinyl alcohol nanofiber networks for effective Li metal anodes.

PubMed

Wang, Gang; Xiong, Xunhui; Lin, Zhihua; Zheng, Jie; Fenghua, Zheng; Li, Youpeng; Liu, Yanzhen; Yang, Chenghao; Tang, Yiwei; Liu, Meilin

2018-05-31

Lithium metal anodes are considered to be the most promising anode material for next-generation advanced energy storage devices due to their high reversible capacity and extremely low anode potential. Nevertheless, the formation of dendritic Li, induced by the repeated breaking and repairing of solid electrolyte interphase layers, always causes poor cycling performance and low coulombic efficiency, as well as serious safety problems, which have hindered the practical application of Li anodes for a long time. Herein, we design an electrode by covering a polyvinyl alcohol layer with a three-dimensional nanofiber network structure through an electrospinning technique. The polar functional groups on the surface of the polymer nanofibers can restrict the deposition of Li along the fibers and regulate the deposition of Li uniformly in the voids between the nanofibers. Owing to the structural features of the polymer, the modified Li|Cu electrode displays excellent cycle stability, with a high coulombic efficiency of 98.6% after 200 cycles at a current density of 1 mA cm-2 under a deposition capacity of 1 mA h cm-2, whilst the symmetric cell using the polymer modified Li anode shows stable cycling with a low hysteresis voltage of ∼80 mV over 600 h at a current density of 5 mA cm-2.

Outstanding Li-storage performance of LiFePO4@MWCNTs cathode material with 3D network structure for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Sun, Xiaodong; Zhang, Le

2018-05-01

In this work, the MWCNTs-decorated LiFePO4 microspheres (LiFePO4@MWCNTs) with a 3D network structure have been synthesized by a facile and efficient spray-drying approach followed by solid-state reaction in a reduction atmosphere. In the as-prepared composite, the MWCNTs around LiFePO4 nanoparticles can provide 3D conductive networks which greatly facilitate the transport of Li+-ion and electron during the electrochemical reaction. Compared to the pure LiFePO4 material, the LiFePO4@MWCNTs composite as cathode for lithium-ion batteries exhibits significantly improved Li-storage performance in terms of rate capability and cyclic stability. Therefore, we can speculate that the spray-drying approach is a promising route to prepare the high-performance electrode materials with 3D network structure for electrochemical energy storage.

Thermophysical properties of LiCoO₂-LiMn₂O₄ blended electrode materials for Li-ion batteries.

PubMed

Gotcu, Petronela; Seifert, Hans J

2016-04-21

Thermophysical properties of two cathode types for lithium-ion batteries were measured by dependence on temperature. The cathode materials are commercial composite thick films containing LiCoO2 and LiMn2O4 blended active materials, mixed with additives (binder and carbon black) deposited on aluminium current collector foils. The thermal diffusivities of the cathode samples were measured by laser flash analysis up to 673 K. The specific heat data was determined based on measured composite specific heat, aluminium specific heat data and their corresponding measured mass fractions. The composite specific heat data was measured using two differential scanning calorimeters over the temperature range from 298 to 573 K. For a comprehensive understanding of the blended composite thermal behaviour, measurements of the heat capacity of an additional LiMn2O4 sample were performed, and are the first experimental data up to 700 K. Thermal conductivity of each cathode type and their corresponding blended composite layers were estimated from the measured thermal diffusivity, the specific heat capacity and the estimated density based on metallographic methods and structural investigations. Such data are highly relevant for simulation studies of thermal management and thermal runaway in lithium-ion batteries, in which the bulk properties are assumed, as a common approach, to be temperature independent.

In situ catalytic synthesis of high-graphitized carbon-coated LiFePO4 nanoplates for superior Li-ion battery cathodes.

PubMed

Ma, Zhipeng; Fan, Yuqian; Shao, Guangjie; Wang, Guiling; Song, Jianjun; Liu, Tingting

2015-02-04

The low electronic conductivity and one-dimensional diffusion channel along the b axis for Li ions are two major obstacles to achieving high power density of LiFePO4 material. Coating carbon with excellent conductivity on the tailored LiFePO4 nanoparticles therefore plays an important role for efficient charge and mass transport within this material. We report here the in situ catalytic synthesis of high-graphitized carbon-coated LiFePO4 nanoplates with highly oriented (010) facets by introducing ferrocene as a catalyst during thermal treatment. The as-obtained material exhibits superior performances for Li-ion batteries at high rate (100 C) and low temperature (-20 °C), mainly because of fast electron transport through the graphitic carbon layer and efficient Li(+)-ion diffusion through the thin nanoplates.

Transport Properties of LiTFSI-Acetamide Room Temperature Molten Salt Electrolytes Applied in an Li-Ion Battery

NASA Astrophysics Data System (ADS)

Yang, Chao-Chen; Hsu, Hsin-Yi; Hsu, Chen-Ruei

2007-11-01

In the present work some transport properties of the binary room temperature molten salt (RTMS) lithium bis(trifluoromethane sulfone)imide (LiTFSI)-acetamide [LiN(SO2CF3)2-CH3CONH2], applied in an Li-ion battery, have been investigated. The phase diagram was determined by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The result reveals that the binary RTMS has an eutectic point at 201 K and the 30 mol% LiTFSI composition. The electric conductivity was measured using a direct current computerized method. The result shows that the conductivities of the melts increase with increasing temperature and acetamide content. The densities of all melts decrease with increasing temperature and acetamide content. The equivalent conductivities were fitted by the Arrhenius equation, where the activation energies were 18.15, 18.52, 20.35, 25.08 kJ/mol for 10, 20, 30, 40 mol% LiTFSI, respectively. Besides the relationships between conductivity, density composition and temperature, of the ion interaction is discussed.

Data products of NASA Goddard's LiDAR, hyperspectral, and thermal airborne imager (G-LiHT)

NASA Astrophysics Data System (ADS)

Corp, Lawrence A.; Cook, Bruce D.; McCorkel, Joel; Middleton, Elizabeth M.

2015-06-01

Scientists in the Biospheric Sciences Laboratory at NASA's Goddard Space Flight Center have undertaken a unique instrument fusion effort for an airborne package that integrates commercial off the shelf LiDAR, Hyperspectral, and Thermal components. G-LiHT is a compact, lightweight and portable system that can be used on a wide range of airborne platforms to support a number of NASA Earth Science research projects and space-based missions. G-LiHT permits simultaneous and complementary measurements of surface reflectance, vegetation structure, and temperature, which provide an analytical framework for the development of new algorithms for mapping plant species composition, plant functional types, biodiversity, biomass, carbon stocks, and plant growth. G-LiHT and its supporting database are designed to give scientists open access to the data that are needed to understand the relationship between ecosystem form and function and to stimulate the advancement of synergistic algorithms. This system will enhance our ability to design new missions and produce data products related to biodiversity and climate change. G-LiHT has been operational since 2011 and has been used to collect data for a number of NASA and USFS sponsored studies, including NASA's Carbon Monitoring System (CMS) and the American ICESat/GLAS Assessment of Carbon (AMIGA-Carb). These acquisitions target a broad diversity of forest communities and ecoregions across the United States and Mexico. Here, we will discuss the components of G-LiHT, their calibration and performance characteristics, operational implementation, and data processing workflows. We will also provide examples of higher level data products that are currently available.

Probing anode degradation in automotive Li-ion batteries

NASA Astrophysics Data System (ADS)

Kwon, Ou Jung

The lithium-ion battery is drawing attention as a power source for future clean and fuel-efficient vehicles. Although the Li-ion battery presently shows best performance for energy density and power density compared to other rechargeable batteries, some degradation problems still remain as key challenges for long-term durability in automotive applications. Among those problems, Li deposition is well known for causing permanent capacity loss. Fundamental mechanisms of Li deposition in the carbon anode are, however, not fully understood, especially at subzero temperature and/or under high rate charge. This dissertation introduces comprehensive study of Li deposition using automotive 18650 Li-ion cells. The mechanism and relevant diagnostic methods as well as preventive charging protocol are discussed. In part one, a new diagnostic tool is introduced utilizing 3-electrode cell system, which measures thermodynamic and kinetic parameters of cathode and anode, respectively, as a function of temperature and SOC (state of charge): open circuit potential (OCP); Li diffusion coefficient in active particles; and internal resistance. These data are employed to understand electrochemical reaction and its thermal interaction under charging conditions that result in Li deposition. Part two provides a threshold parameter for the onset of Li deposition, which is not commonly used anode potential but charge capacity, or more specifically the amount of Li+ ions participating in intercalation reaction without Li deposition at given charging circumstances. This is called the critical charge capacity in this thesis, beyond which capacity loss at normal operating condition is observed, which becomes more serious as temperature is lowered and/or charge C-rate increases. Based on these experimental results, the mechanism of Li deposition is proposed as the concept of anode particle surface saturation, meaning that once the anode particle surface is saturated with Li in any charging

Insight into fast ion migration kinetics of a new hybrid single Li-ion conductor based on aluminate complexes for solid-state Li-ion batteries.

PubMed

Feng, Yancong; Tan, Rui; Zhao, Yan; Gao, Rongtan; Yang, Luyi; Yang, Jinlong; Li, Hao; Zhou, Guofu; Chen, Haibiao; Pan, Feng

2018-03-29

A novel hybrid single Li-ion conductor (SLIC) for a Li-ion solid electrolyte was prepared by mixing aluminate complexes-polyethylene glycol (LiAl-PEG) and polyethylene oxide (PEO) for solid-state Li-ion batteries. The LiAl-PEG/PEO blend possesses high thermal stability and electrochemical stability with an oxidation decomposition voltage up to 4.8 V. Notably, this hybrid SLIC exhibits not only excellent Li-ion migration kinetics, but also good ionic conductivity as high as 4.0 × 10-5 and 2.6 × 10-4 S cm-1 at 30 and 100 °C, respectively, which is much higher than previously reported SLICs. Importantly, by the combination of molecular dynamics simulations and experiment measurements, the mechanisms of Li-ion migration across the SLIC (LiAl-PEG), the salt-in-polymer (LiClO4/PEO) and the optimized SLIC (LiAl-PEG/PEO) were systematically investigated for the first time. The new hopping transport mechanism was verified for the SLIC system at the nanoscale. As for the hybrid SLIC, PEO chains enhance the segmental mobility of the ether-chains bonded with Al atoms, improve the ionicity, and provide extra ionic paths for Li transfer, resulting in the optimized Li-ion migration kinetics of LiAl-PEG/PEO.

(Cu,C)Ba2Ca3Cu4Ox (LiF)y: addition of LiF—an effective way to synthesize overdoped superconductor

NASA Astrophysics Data System (ADS)

Badica, P.; Iyo, A.; Aldica, G.; Kito, H.; Crisan, A.; Tanaka, Y.

2004-03-01

(Cu,C)Ba2Ca3Cu4Ox superconductor with addition of y mol LiF has been synthesized by a high-pressure method. For the same synthesis conditions it was found that (almost) single-phase Cu, C-1234 samples can be synthesized for yLiF = 0-0.1 if the amount of z mol AgO oxidizer is increased linearly from zAgO = 0.45 to 0.73 and for yLiF = 0.1-0.2 if zAgO = 0.73 = constant. Transport measurements (rgr(T) and room-temperature Seebeck coefficient) have shown that these samples are overdoped: LiF is an effective addition for synthesis of overdoped Cu, C-1234 with a controlled level of carriers. LiF addition continuously decreases Tc. The critical point at yLiF = 0.1 is discussed as the solubility limit of LiF and/or the point where the doping mechanism changes. It is proposed that the reason is the reaction of extra Li with C and O to form Li2CO3, inducing a lower concentration of C in Cu, C-1234/LiF crystals, and at the same time a possible substitution of Li not only for the Cu site but also for the Ca site, resulting in formation of a higher amount of residual Ca0.828CuO2 (for yLiF>0.1). LiF induces the formation of a liquid phase and acts as a flux promoting the formation of Cu,C-12 (n-1)n with n \\ge 4 . LiF modifies to some degree the grain growth from a 3D to a 2D type (thinner platelike grains have been observed in the LiF added samples).

Natural ageing responses of duplex structured Mg-Li based alloys

PubMed Central

Li, C. Q.; Xu, D. K.; Wang, B. J.; Sheng, L. Y.; Qiao, Y. X.; Han, E. H.

2017-01-01

Natural ageing responses of duplex structured Mg-6%Li and Mg-6%Li-6%Zn-1.2%Y alloys have been investigated. Microstructural analyses revealed that the precipitation and coarsening process of α-Mg particles could occur in β-Li phases of both two alloys during ageing process. Since a certain amount of Mg atoms in β-Li phases were consumed for the precipitation of abundant tiny MgLiZn particles, the size of α-Mg precipitates in Mg-6%Li-6%Zn-1.2%Y alloy was relatively smaller than that in Mg-6%Li alloy. Micro hardness measurements demonstrated that with the ageing time increasing, the α-Mg phases in Mg-6%Li alloy could have a constant hardness value of 41 HV, but the contained β-Li phases exhibited a slight age-softening response. Compared with the Mg-6%Li alloy, the age-softening response of β-Li phases in Mg-6%Li-6%Zn-1.2%Y alloy was much more profound. Meanwhile, a normal age-hardening response of α-Mg phases was maintained. Tensile results indicated that obvious ageing-softening phenomenon in terms of macro tensile strength occurred in both two alloys. Failure analysis demonstrated that for the Mg-6%Li alloy, cracks were preferentially initiated at α-Mg/β-Li interfaces. For the Mg-6%Li-6%Zn-1.2%Y alloy, cracks occurred at both α-Mg/β-Li interfaces and slip bands in α-Mg and β-Li phases. PMID:28053318

The Technology of LiFi: A Brief Introduction

NASA Astrophysics Data System (ADS)

Ramadhani, E.; Mahardika, G. P.

2018-03-01

Light Fidelity (LiFi) is a Visible Light Communication (VLC) based technology that making a light as a media of communication replacing the cable wire communication. LiFi is evolve to overcome the rate speed in WiFi, while using LiFi the rate speed can reach until 14 Gbps. This paper presents an introduction of the LiFi technology including the architecture, modulation, performance, and the challenges. The result of this paper can be used as a reference and knowledge to develop some of the LiFi technology.

Self-assembled LiFePO4 nanowires with high rate capability for Li-ion batteries.

PubMed

Peng, Lele; Zhao, Yu; Ding, Yu; Yu, Guihua

2014-08-28

Controlling the dimensions in the nanometer scale of olivine-type LiFePO4 has been regarded as one of the most effective strategies to improve its electrochemical performance for Li-ion batteries. In this communication, we demonstrate a novel LiFePO4 nanoarchitecture, which is composed of self-assembled single-crystalline nanowires and exhibits good rate capability with a reversible capacity of ∼110 mA h g(-1) at a current rate of 30 C, and a stable capacity retention of ∼86% after 1000 cycles at a current rate of 10 C.

Potential energy surfaces of the low-lying electronic states of the Li + LiCs system

NASA Astrophysics Data System (ADS)

Jasik, P.; Kilich, T.; Kozicki, J.; Sienkiewicz, J. E.

2018-03-01

Ab initio quantum chemistry calculations are performed for the mixed alkali triatomic system. Global minima of the ground and first excited doublet states of the trimer are found and Born-Oppenheimer potential energy surfaces of the Li atom interacting with the LiCs molecule were calculated for these states. The lithium atom is placed at various distances and bond angles from the lithium-caesium dimer. Three-body nonadditive forces of the Li2Cs molecule in the global minimum are investigated. Dimer-atom interactions are found to be strongly attractive and may be important in the experiments, particularly involving cold alkali polar dimers.

Electrochemical performance of all-solid-state Li batteries based LiMn 0.5Ni 0.5O 2 cathode and NASICON-type electrolyte

NASA Astrophysics Data System (ADS)

Xie, J.; Imanishi, N.; Zhang, T.; Hirano, A.; Takeda, Y.; Yamamoto, O.; Zhao, X. B.; Cao, G. S.

LiNi 0.5Mn 0.5O 2 thin films have been deposited on the NASICON-type glass ceramics, Li 1+ x+ yAl xTi 2- xSi yP 3- yO 12 (LATSP), by radio frequency (RF) magnetron sputtering followed by annealing. The films have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectroscopy. All-solid-state Li/PEO 18-Li(CF 3SO 2) 2N/LATSP/LiNi 0.5Mn 0.5O 2/Au cells are fabricated using the LiNi 0.5Mn 0.5O 2 thin films and the LATSP electrolyte. The electrochemical performance of the cells is investigated by galvanostatic cycling, cyclic voltammetry (CV), potentiostatic intermittent titration technique (PITT) and electrochemical impedance spectroscopy (EIS). Interfacial reactions between LiNi 0.5Mn 0.5O 2 and LATSP occur at a temperature as low as 300 °C with the formation of Mn 3O 4, resulting in an increased obstacle for Li-ion diffusion across the LiNi 0.5Mn 0.5O 2/LATSP interface. The electrochemical performance of the cells is limited by the interfacial resistance between LATSP and LiNi 0.5Mn 0.5O 2 as well as the Li-ion diffusion kinetics in LiNi 0.5Mn 0.5O 2 bulk.

Structural and Electrochemical Characterization of Pure LiFePO 4 and Nanocomposite C- LiFePO 4 Cathodes for Lithium Ion Rechargeable Batteries

DOE PAGES

Kumar, Arun; Thomas, R.; Karan, N. K.; ...

2009-01-01

Pure limore » thium iron phosphate ( LiFePO 4 ) and carbon-coated LiFePO 4 (C- LiFePO 4 ) cathode materials were synthesized for Li-ion batteries. Structural and electrochemical properties of these materials were compared. X-ray diffraction revealed orthorhombic olivine structure. Micro-Raman scattering analysis indicates amorphous carbon, and TEM micrographs show carbon coating on LiFePO 4 particles. Ex situ Raman spectrum of C- LiFePO 4 at various stages of charging and discharging showed reversibility upon electrochemical cycling. The cyclic voltammograms of LiFePO 4 and C- LiFePO 4 showed only a pair of peaks corresponding to the anodic and cathodic reactions. The first discharge capacities were 63, 43, and 13 mAh/g for C/5, C/3, and C/2, respectively for LiFePO 4 where as in case of C- LiFePO 4 that were 163, 144, 118, and 70 mAh/g for C/5, C/3, C/2, and 1C, respectively. The capacity retention of pure LiFePO 4 was 69% after 25 cycles where as that of C- LiFePO 4 was around 97% after 50 cycles. These results indicate that the capacity and the rate capability improved significantly upon carbon coating.« less

Identifying the Structure of the Intermediate, Li 2/3CoPO 4, Formed during Electrochemical Cycling of LiCoPO 4

DOE PAGES

Strobridge, Fiona C.; Clément, Raphaële J.; Leskes, Michal; ...

2014-11-03

In situ synchrotron diffraction measurements and subsequent Rietveld refinements are used to show that the high energy density cathode material LiCoPO 4 (space group Pnma) undergoes two distinct two-phase reactions upon charge and discharge, both occurring via an intermediate Li 2/3(Co 2+) 2/3(Co 3+) 1/3PO 4 phase. Two resonances are observed for Li 2/3CoPO 4 with intensity ratios of 2:1 and 1:1 in the 31P and 7Li NMR spectra, respectively. An ordering of Co 2+/Co 3+ oxidation states is proposed within a (a × 3b × c) supercell, and Li +/vacancy ordering is investigated using experimental NMR data in combinationmore » with first-principles solid-state DFT calculations. In the lowest energy configuration, both the Co 3+ ions and Li vacancies are found to order along the b-axis. Two other low energy Li +/vacancy ordering schemes are found only 5 meV per formula unit higher in energy. All three configurations lie below the LiCoPO 4–CoPO 4 convex hull and they may be readily interconverted by Li + hops along the b-direction.« less

Electrical conductivity in Li2O2 and its role in determining capacity limitations in non-aqueous Li-O2 batteries.

PubMed

Viswanathan, V; Thygesen, K S; Hummelshøj, J S; Nørskov, J K; Girishkumar, G; McCloskey, B D; Luntz, A C

2011-12-07

Non-aqueous Li-air or Li-O(2) cells show considerable promise as a very high energy density battery couple. Such cells, however, show sudden death at capacities far below their theoretical capacity and this, among other problems, limits their practicality. In this paper, we show that this sudden death arises from limited charge transport through the growing Li(2)O(2) film to the Li(2)O(2)-electrolyte interface, and this limitation defines a critical film thickness, above which it is not possible to support electrochemistry at the Li(2)O(2)-electrolyte interface. We report both electrochemical experiments using a reversible internal redox couple and a first principles metal-insulator-metal charge transport model to probe the electrical conductivity through Li(2)O(2) films produced during Li-O(2) discharge. Both experiment and theory show a "sudden death" in charge transport when film thickness is ~5 to 10 nm. The theoretical model shows that this occurs when the tunneling current through the film can no longer support the electrochemical current. Thus, engineering charge transport through Li(2)O(2) is a serious challenge if Li-O(2) batteries are ever to reach their potential. © 2011 American Institute of Physics

Three-volt lithium-ion battery with Li[Ni 1/2Mn 3/2]O 4 and the zero-strain insertion material of Li[Li 1/3Ti 5/3]O 4

NASA Astrophysics Data System (ADS)

Ariyoshi, Kingo; Yamamoto, Satoshi; Ohzuku, Tsutomu

A 3 V lithium-ion cell with Li[Ni 1/2Mn 3/2]O 4 ( Fd 3¯m ; a=8.17 Å) and the zero-strain insertion material of Li[Li 1/3Ti 5/3]O 4 ( Fd 3¯m ; a=8.36 Å) was examined with an emphasis on rate-capability and cycle life. This cell showed a quite flat operating voltage of 3.2 V with excellent cycleability. Accelerated cycle tests indicated that 83% of the initial capacity was delivered and stored even after 1100 cycles. Although the calculated energy density of a Li[Li 1/3Ti 5/3]O 4/Li[Ni 1/2Mn 3/2]O 4 cell was about 250 Wh kg -1 or 1000 Wh dm -3 based on the active material weight or volume, the 3 V lithium-ion battery exhibited positive characteristic features, such as flatness in operating voltage, high rate capability, and cycle life.

Measuring Li + inventory losses in LiCoO 2/graphite cells using Raman microscopy

DOE PAGES

Snyder, Chelsea Marie; Apblett, Christopher A.; Grillet, Anne; ...

2016-03-25

Here, the contribution from loss of Li + inventory to capacity fade is described for slow rates (C/10) and long-term cycling (up to 80 cycles). It was found through electrochemical testing and ex-situ Raman analysis that at these slow rates, the entirety of capacity loss up to 80 cycles can be explained by loss of Li + inventory in the cell. The Raman spectrum of LiCoO 2 is sensitive to the state of lithiation and can therefore be leveraged to quantify the state of lithiation for individual particles. With these Raman derived estimates, the lithiation state of the cathode inmore » the discharged state is compared to electrochemical data as a function of cycle number. High correlation is found between Raman quantifications of cycleable lithium and the capacity fade. Additionally, the linear relationship between discharge capacity and cell overpotential suggests that the loss of capacity stems from an impedance rise of the electrodes, which based on Li inventory losses, is caused by SEI formation and repair.« less

3D non-LTE corrections for the 6Li/7Li isotopic ratio in solar-type stars

NASA Astrophysics Data System (ADS)

Harutyunyan, G.; Steffen, M.; Mott, A.; Caffau, E.; Israelian, G.; González Hernández, J. I.; Strassmeier, K. G.

Doppler shifts induced by convective motions in stellar atmospheres affect the shape of spectral absorption lines and create slightly asymmetric line profiles. It is important to take this effect into account in modeling the subtle depression created by the 6Li isotope which lies on the red wing of the Li I 670.8 nm resonance doublet line, since convective motions in stellar atmospheres can mimic a presence of 6Li when intrinsically symmetric theoretical line profiles are presumed for the analysis of the 7Li doublet \\citep{cayrel2007}. Based on CO5BOLD hydrodynamical model atmospheres, we compute 3D non-local thermodynamic equilibrium (NLTE) corrections for the 6Li/7Li isotopic ratio by using a grid of 3D NLTE and 1D LTE synthetic spectra. These corrections must be added to the results of the 1D LTE analysis to correct them for the combined 3D non-LTE effects. As one would expect, the resulting corrections are always negative and they range between 0 and -5 %, depending on effective temperature, surface gravity, and metallicity. For each metallicity we derive an analytic expression approximating the 3D NLTE corrections as a function of effective temperature, surface gravity and projected rotational velocity.

An Investigation of Facile One-Pot Synthesis of Li2FeSiO4/C Composite for Li Ion Batteries

NASA Astrophysics Data System (ADS)

Thirumoolam, Mani Chandran; Manikandan, Ananda Kumar; Sivaramakrishnan, Balaji; Kaluvan, Hariharan; Gowravaram, Mohan Rao

2018-03-01

Li2FeSiO4 and its carbon composite are prepared by an urea-assisted combustion method. The synthesis has been carried out in different urea concentrations, namely 1 Molar (M), 2 M and 3 M urea in the cost-effective ambient atmospheric condition. The x-ray diffraction analysis confirms the orthorhombic structure of Li2FeSiO4 compounds. The urea-assisted combustion reaction enhanced the phase purity of the compound and prevented the oxidation of ferrous ions in Li2FeSiO4. The x-ray photo electron spectroscopy analysis further confirmed the reduction of Fe3+ concentration in Li2FeSiO4 while adding urea. The Li2FeSiO4 compound formation in the presence of urea occurred at a temperature < 623 K. The one-pot synthesis of Li2FeSiO4/C with the help of starch and urea in ambient atmospheric condition resulted in Li2FeSiO4 with an orthorhombic crystal structure. The carbon coating in an amorphous nature is observed and the lattice dimension values of Li2FeSiO4/C are 6.248 Å, 5.330 Å, and 5.029 Å. The lattice parameter has remained unchanged with carbon addition. The addition of 5% carbon to Li2FeSiO4 improves the electrical conductivity and lithium diffusion coefficient to 7.24 × 10-4 S cm-1 and 5.54 × 10-6 cm2, respectively. The coulombic efficiency and capacity retention after 50 cycles of Li2FeSiO4/C composite are around 83% and 95%, respectively.

DMSO-Li2O2 Interface in the Rechargeable Li-O2 Battery Cathode: Theoretical and Experimental Perspectives on Stability.

PubMed

Schroeder, Marshall A; Kumar, Nitin; Pearse, Alexander J; Liu, Chanyuan; Lee, Sang Bok; Rubloff, Gary W; Leung, Kevin; Noked, Malachi

2015-06-03

One of the greatest obstacles for the realization of the nonaqueous Li-O2 battery is finding a solvent that is chemically and electrochemically stable under cell operating conditions. Dimethyl sulfoxide (DMSO) is an attractive candidate for rechargeable Li-O2 battery studies; however, there is still significant controversy regarding its stability on the Li-O2 cathode surface. We performed multiple experiments (in situ XPS, FTIR, Raman, and XRD) which assess the stability of the DMSO-Li2O2 interface and report perspectives on previously published studies. Our electrochemical experiments show long-term stable cycling of a DMSO-based operating Li-O2 cell with a platinum@carbon nanotube core-shell cathode fabricated via atomic layer deposition, specifically with >45 cycles of 40 h of discharge per cycle. This work is complemented by density functional theory calculations of DMSO degradation pathways on Li2O2. Both experimental and theoretical evidence strongly suggests that DMSO is chemically and electrochemically stable on the surface of Li2O2 under the reported operating conditions.

Rechargeable Li/Li(x)CoO(2) 100 Ah/600 Ah Battery With Integral Smart Charge Control

DTIC Science & Technology

1999-03-01

Rechargeable Li/LixCo02100 Ah/600 Ah Battery with Integral Smart Charge Control By Charles J. Kelly ^ (Alliant Techsystems, Inc., Alliant Power...Rechargeable Li/LixCo02100 Ah/600 Ah Battery with Integral Smart Charge Control By Charles J. Kelly (Alliant Techsystems, Inc., Alliant Power Sources...AND SUBTITLE Rechargeable Li/LixCo02100 Ah/600 Ah Battery with Integral Smart Charge Control 6 AUTHOR(S) C. J. Kelly (Alliant Power Sources Co

Measurement of fast neutron detection efficiency with 6Li and 7Li enriched CLYC scintillators

NASA Astrophysics Data System (ADS)

Mentana, A.; Camera, F.; Giaz, A.; Blasi, N.; Brambilla, S.; Ceruti, S.; Gini, L.; Groppi, F.; Manenti, S.; Million, B.; Riboldi, S.

2016-10-01

The CLYC (Cs2LiYC6:Ce) crystal belongs to the elpasolite scintillator family, discovered about 15 years ago. It is a very interesting material because of its good energy resolution and its capability to identify and measure gamma rays and fast/thermal neutrons. In the present work, the fast neutron detection efficiency for two different CLYC cylindrical samples has been measured. These two crystals, both with dimension (thickness x diameter) 1”×1”, were respectively enriched with more than 99% of 7Li (CLYC-7) and with ∼ 95% of 6Li (CLYC-6). The presence of the 6Li isotope makes the CLYC-6 ideal to detect thermal neutrons. In order to compare the two scintillators, only the detection efficiency for fast neutrons was considered, neglecting the energy region associated to thermal neutrons in both the crystals. The measurement was performed at the L.A.S.A. Laboratory of INFN and University of Milano (Italy), using a 241Am-Be source.

Novel Organic-Inorganic Hybrid Electrolyte to Enable LiFePO4 Quasi-Solid-State Li-Ion Batteries Performed Highly around Room Temperature.

PubMed

Tan, Rui; Gao, Rongtan; Zhao, Yan; Zhang, Mingjian; Xu, Junyi; Yang, Jinlong; Pan, Feng

2016-11-16

A novel type of organic-inorganic hybrid polymer electrolytes with high electrochemical performances around room temperature is formed by hybrid of nanofillers, Y-type oligomer, polyoxyethylene and Li-salt (PBA-Li), of which the T g and T m are significantly lowered by blended heterogeneous polyethers and embedded nanofillers with benefit of the dipole modification to achieve the high Li-ion migration due to more free-volume space. The quasi-solid-state Li-ion batteries based on the LiFePO 4 /15PBA-Li/Li-metal cells present remarkable reversible capacities (133 and 165 mAh g -1 @0.2 C at 30 and 45 °C, respectively), good rate ability and stable cycle performance (141.9 mAh g -1 @0.2 C at 30 °C after 150 cycles).

Electrochemistry of Europium(III) Chloride in 3 LiCl – NaCl, 3 LiCl – 2 KCl, LiCl – RbCl, and 3 LiCl – 2 CsCl Eutectics at Various Temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schroll, Cynthia A.; Chatterjee, Sayandev; Levitskaia, Tatiana G.

Here we report the effect of changing the eutectic melt composition on the electrochemical properties of europium(III) chloride under pyroprocessing conditions. The number of electrons transferred, redox potentials and diffusion coefficients were determined using various electrochemical and spectroelectrochemical techniques in four different eutectic mixtures (3 LiCl - NaCl, 3 LiCl - 2 KCl, 3 LiCl - RbCl, and 3 LiCl - 2 CsCl) while varying the temperature of the melt. It was determined that Eu3+ undergoes a one electron reduction to Eu2+ in each melt at all temperatures evaluated. Within all the melts a positive shift in the redox potentialmore » as well as an increase in the diffusion coefficient for Eu3+ was observed as the temperature increased. Also observed was a positive shift in the redox potential and increase in the diffusion coefficient for Eu3+ as the weighted average of the cationic radii for the melt decreased.« less

Lithium hydroxide, LiOH, at elevated densities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermann, Andreas; Ashcroft, N. W.; Hoffmann, Roald

2014-07-14

We discuss the high-pressure phases of crystalline lithium hydroxide, LiOH. Using first-principles calculations, and assisted by evolutionary structure searches, we reproduce the experimentally known phase transition under pressure, but we suggest that the high-pressure phase LiOH-III be assigned to a new hydrogen-bonded tetragonal structure type that is unique amongst alkali hydroxides. LiOH is at the intersection of both ionic and hydrogen bonding, and we examine the various ensuing structural features and their energetic driving mechanisms. At P = 17 GPa, we predict another phase transition to a new phase, Pbcm-LiOH-IV, which we find to be stable over a wide pressuremore » range. Eventually, at extremely high pressures of 1100 GPa, the ground state of LiOH is predicted to become a polymeric structure with an unusual graphitic oxygen-hydrogen net. However, because of its ionic character, the anticipated metallization of LiOH is much delayed; in fact, its electronic band gap increases monotonically into the TPa pressure range.« less

Effect of Hua Yu Xiao Zheng decoction on the expression levels of vascular endothelial growth factor and angiopoietin-2 in rats with endometriosis.

PubMed

Chen, Zhen-Zhen; Gong, Xin

2017-12-01

The aims of the present study were to investigate the effects of a traditional Chinese medicine, Hua Yu Xiao Zheng (HYXZ) decoction, on surgically induced endometriosis in a rat model and to determine the possible underlying regulatory mechanisms. A total of 108 female Sprague-Dawley rats were divided into the control group (n=12) and endometriosis group (EM group; n=96), in which endometriosis was surgically induced in model rats by autotransplantation of endometrial tissues and 72 rats survived. After 3 weeks, the EM model rats were randomly divided into four subgroups (n=18), including the untreated model group, and three groups administered 7, 14 or 21 g/kg HYXZ decoction. Following 28 days of treatment, the associated proteins and genes of ectopic endometrial tissues were analyzed using immunohistochemistry, western blotting and quantitative polymerase chain reaction to investigate the underlying mechanisms. Compared with the model group, the size of the endometriotic implants decreased significantly in the HYXZ-treated groups. Furthermore, the expression levels of vascular endothelial growth factor (VEGF) and angiopoietin-2 (Ang-2) were significantly decreased in HYXZ-treated groups compared with the model group. These results indicate that HYXZ affected the inhibition of angiogenesis and decreased the endometriotic implant volumes and histopathological scores. The effectiveness of HYXZ may be partially attributed to the decrease of VEGF and Ang-2 expression levels in the ectopic endometrium.

Li-ion site disorder driven superionic conductivity in solid electrolytes: a first-principles investigation of β-Li 3PS 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phani Dathar, Gopi Krishna; Balachandran, Janakiraman; Kent, Paul R. C.

The attractive safety and long-term stability of all solid-state batteries has added a new impetus to the discovery and development of solid electrolytes for lithium batteries. Recently several superionic lithium conducting solid electrolytes have been discovered. All the superionic lithium containing compounds (β-Li 3PS 4 and Li 10GeP 2S 12 and oxides, predominantly in the garnet phase) have partially occupied sites. This naturally begs the question of understanding the role of partial site occupancies (or site disorder) in optimizing ionic conductivity in these family of solids. In this paper, we find that for a given topology of the host lattice,more » maximizing the number of sites with similar Li-ion adsorption energies, which gives partial site occupancy, is a natural way to increase the configurational entropy of the system and optimize the conductivity. For a given topology and density of Li-ion adsorption sites, the ionic conductivity is maximal when the number of mobile Li-ions are equal to the number of mobile vacancies, also the very condition for achieving maximal configurational entropy. We demonstrate applicability of this principle by elucidating the role of Li-ion site disorder and the local chemical environment in the high ionic conductivity of β-Li 3PS 4. In addition, for β-Li 3PS 4 we find that a significant density of vacancies in the Li-ion sub-lattice (~25%) leads to sub-lattice melting at (~600 K) leading to a molten form for the Li-ions in an otherwise solid anionic host. This gives a lithium site occupancy that is similar to what is measured experimentally. We further show that quenching this disorder can improve conductivity at lower temperatures. As a consequence, we discover that (a) one can optimize ionic conductivity in a given topology by choosing a chemistry/composition that maximizes the number of mobile-carriers i.e. maximizing both mobile Li-ions and vacancies, and (b) when the concentration of vacancies becomes significant

Li-ion site disorder driven superionic conductivity in solid electrolytes: a first-principles investigation of β-Li 3PS 4

DOE PAGES

Phani Dathar, Gopi Krishna; Balachandran, Janakiraman; Kent, Paul R. C.; ...

2016-12-09

The attractive safety and long-term stability of all solid-state batteries has added a new impetus to the discovery and development of solid electrolytes for lithium batteries. Recently several superionic lithium conducting solid electrolytes have been discovered. All the superionic lithium containing compounds (β-Li 3PS 4 and Li 10GeP 2S 12 and oxides, predominantly in the garnet phase) have partially occupied sites. This naturally begs the question of understanding the role of partial site occupancies (or site disorder) in optimizing ionic conductivity in these family of solids. In this paper, we find that for a given topology of the host lattice,more » maximizing the number of sites with similar Li-ion adsorption energies, which gives partial site occupancy, is a natural way to increase the configurational entropy of the system and optimize the conductivity. For a given topology and density of Li-ion adsorption sites, the ionic conductivity is maximal when the number of mobile Li-ions are equal to the number of mobile vacancies, also the very condition for achieving maximal configurational entropy. We demonstrate applicability of this principle by elucidating the role of Li-ion site disorder and the local chemical environment in the high ionic conductivity of β-Li 3PS 4. In addition, for β-Li 3PS 4 we find that a significant density of vacancies in the Li-ion sub-lattice (~25%) leads to sub-lattice melting at (~600 K) leading to a molten form for the Li-ions in an otherwise solid anionic host. This gives a lithium site occupancy that is similar to what is measured experimentally. We further show that quenching this disorder can improve conductivity at lower temperatures. As a consequence, we discover that (a) one can optimize ionic conductivity in a given topology by choosing a chemistry/composition that maximizes the number of mobile-carriers i.e. maximizing both mobile Li-ions and vacancies, and (b) when the concentration of vacancies becomes significant

Electrochemical Formation of Mg-Li-Sm Alloys by Codeposition from LiCl-KCl-MgCl2-SmCl3 Molten Salts

NASA Astrophysics Data System (ADS)

Han, Wei; Wang, Fengli; Tian, Yang; Zhang, Milin; Yan, Yongde

2011-12-01

In this article, the electrochemical method of preparing Mg-Li-Sm alloys by codeposition in LiCl-KCl-MgCl2-SmCl3 melts was investigated. Transient electrochemical techniques, such as cyclic voltammetry, chronopotentiometry, and chronoamperometry were used to explore the electrochemical formation of Mg-Li-Sm alloys. Chronopotentiograms demonstrated that the codepositon of Mg, Li, and Sm occurred when current densities were more negative than -0.31 A cm-2. Chronoamperograms indicated that the onset potential for the codeposition of Mg, Li, and Sm was -2.40 V, and the codeposition of Mg, Li, and Sm was formed when the applied potentials were more negative than -2.40 V. The different phases of Mg-Li-Sm alloys were prepared by galvanostatic electrolysis and characterized by X-ray diffraction (XRD), optical microscope (OM), and scanning electron microscopy (SEM). An inductively coupled plasma (ICP) analysis showed that the lithium and samarium contents in Mg-Li-Sm alloys could be controlled by the concentrations of MgCl2 and SmCl3. The results demonstrated that Sm could refine the grains dramatically. When the Sm content was 0.8 wt pct, the grain size was the finest.

Benchmark Linelists and Radiative Cooling Functions for LiH Isotopologues

NASA Astrophysics Data System (ADS)

Diniz, Leonardo G.; Alijah, Alexander; Mohallem, José R.

2018-04-01

Linelists and radiative cooling functions in the local thermodynamic equilibrium limit have been computed for the six most important isotopologues of lithium hydride, 7LiH, 6LiH, 7LiD, 6LiD, 7LiT, and 6LiT. The data are based on the most accurate dipole moment and potential energy curves presently available, the latter including adiabatic and leading relativistic corrections. Distance-dependent reduced vibrational masses are used to account for non-adiabatic corrections of the rovibrational energy levels. Even for 7LiH, for which linelists have been reported previously, the present linelist is more accurate. Among all isotopologues, 7LiH and 6LiH are the best coolants, as shown by the radiative cooling functions.

LiDAR utility for natural resource managers

Treesearch

Andrew Thomas Hudak; Jeffrey Scott Evans; Alistair Mattthew Stuart Smith

2009-01-01

Applications of LiDAR remote sensing are exploding, while moving from the research to the operational realm. Increasingly, natural resource managers are recognizing the tremendous utility of LiDAR-derived information to make improved decisions. This review provides a cross-section of studies, many recent, that demonstrate the relevance of LiDAR across a suite of...

High Rate Performing Li-ion Battery

DTIC Science & Technology

2015-02-09

this storage capacity is known so far the highest among all phosphate-based cathode materials. Unlike olivine LiFePO4 with inherent low lithium ion...1 ). 24 However, similar to LiFePO4 , the main drawback of LVP is its intrinsic poor electronic conductivity (10 −8 Scm −1 ) 25 which can hinder...Fisher, C. A. J. & Slater, P. R. Atomic-scale Investigation of Defects, Dopants, and Lithium Transport in the LiFePO4 Olivine-type Battery

Lithium and Isotopic Ratio Li6/Li7 in Magnetic roAp Stars as an Indicator of Active Processes

NASA Astrophysics Data System (ADS)

Polosukhina, N.; Shavrina, A.; Lyashko, D.; Nesvacil, N.; Drake, N.; Smirnova, M.

2015-04-01

The lines of lithium at 6708 Å and 6103 Å are analyzed in high resolution spectra of some sharp-lined and slowly rotating roAp stars. Three spectral synthesis codes— STARSP, ZEEMAN2, and SYNTHM—were used. New lines of rare earth elements (REE) from the DREAM database and the lines calculated on the basis of the NIST energy levels were included. Magnetic splitting and other line broadening processes were taken into account. For both lithium lines, the enhanced abundances of lithium in the atmospheres of the stars studied are obtained. The lithium abundance determined from the Li 6103 Å line is higher than that from the Li 6708 Å for all the stars. This may be evidence of vertical lithium stratification, abnormal temperature distribution, or unidentified blending of the 6103 Å line. Our work on two roAp stars, HD 83368 and HD 60435 (Shavrina et al. 2001) provides evidence of an enhanced lithium abundance near the magnetic-field poles. We can expect similar effects in the sharp-lined roAp stars. High lithium abundance for all the stars and the estimates of the 6Li/7Li ratio (0.2-0.5) can be explained by production of Li in the cosmic ray spallation reactions in the interstellar medium where the stars were born, and by preservation of the original 6Li and 7Li by strong magnetic fields of these stars. The values of the 6Li/7Li ratio expected from production by cosmic rays are about 0.5-0.8 (Knauth et al. 2003; Webber et al. 2002). New laboratory and theoretical gf-values for REE lines are necessary in order to refine our estimates of lithium abundances and the isotopic ratio.

Evidence for anionic redox activity in a tridimensional-ordered Li-rich positive electrode β-Li2IrO3

NASA Astrophysics Data System (ADS)

Pearce, Paul E.; Perez, Arnaud J.; Rousse, Gwenaelle; Saubanère, Mathieu; Batuk, Dmitry; Foix, Dominique; McCalla, Eric; Abakumov, Artem M.; van Tendeloo, Gustaaf; Doublet, Marie-Liesse; Tarascon, Jean-Marie

2017-05-01

Lithium-ion battery cathode materials have relied on cationic redox reactions until the recent discovery of anionic redox activity in Li-rich layered compounds which enables capacities as high as 300 mAh g-1. In the quest for new high-capacity electrodes with anionic redox, a still unanswered question was remaining regarding the importance of the structural dimensionality. The present manuscript provides an answer. We herein report on a β-Li2IrO3 phase which, in spite of having the Ir arranged in a tridimensional (3D) framework instead of the typical two-dimensional (2D) layers seen in other Li-rich oxides, can reversibly exchange 2.5 e- per Ir, the highest value ever reported for any insertion reaction involving d-metals. We show that such a large activity results from joint reversible cationic (Mn+) and anionic (O2)n- redox processes, the latter being visualized via complementary transmission electron microscopy and neutron diffraction experiments, and confirmed by density functional theory calculations. Moreover, β-Li2IrO3 presents a good cycling behaviour while showing neither cationic migration nor shearing of atomic layers as seen in 2D-layered Li-rich materials. Remarkably, the anionic redox process occurs jointly with the oxidation of Ir4+ at potentials as low as 3.4 V versus Li+/Li0, as equivalently observed in the layered α-Li2IrO3 polymorph. Theoretical calculations elucidate the electrochemical similarities and differences of the 3D versus 2D polymorphs in terms of structural, electronic and mechanical descriptors. Our findings free the structural dimensionality constraint and broaden the possibilities in designing high-energy-density electrodes for the next generation of Li-ion batteries.

Li 2Se as a Neutron Scintillator

DOE PAGES

Du, Mao-Hua; Shi, Hongliang; Singh, David J.

2015-06-23

We show that Li 2Se:Te is a potential neutron scintillator material based on density functional calculations. Li 2Se exhibits a number of properties favorable for efficient neutron detection, such as a high Li concentration for neutron absorption, a small effective atomic mass and a low density for reduced sensitivity to background gamma rays, and a small band gap for a high light yield. Our calculations show that Te doping should lead to the formation of deep acceptor complex V Li-Te Se, which can facilitate efficient light emission, similar to the emission activation in Te doped ZnSe.

Enhanced thermal safety and high power performance of carbon-coated LiFePO4 olivine cathode for Li-ion batteries

NASA Astrophysics Data System (ADS)

Zaghib, K.; Dubé, J.; Dallaire, A.; Galoustov, K.; Guerfi, A.; Ramanathan, M.; Benmayza, A.; Prakash, J.; Mauger, A.; Julien, C. M.

2012-12-01

The carbon-coated LiFePO4 Li-ion oxide cathode was studied for its electrochemical, thermal, and safety performance. This electrode exhibited a reversible capacity corresponding to more than 89% of the theoretical capacity when cycled between 2.5 and 4.0 V. Cylindrical 18,650 cells with carbon-coated LiFePO4 also showed good capacity retention at higher discharge rates up to 5C rate with 99.3% coulombic efficiency, implying that the carbon coating improves the electronic conductivity. Hybrid Pulse Power Characterization (HPPC) test performed on LiFePO4 18,650 cell indicated the suitability of this carbon-coated LiFePO4 for high power HEV applications. The heat generation during charge and discharge at 0.5C rate, studied using an Isothermal Microcalorimeter (IMC), indicated cell temperature is maintained in near ambient conditions in the absence of external cooling. Thermal studies were also investigated by Differential Scanning Calorimeter (DSC) and Accelerating Rate Calorimeter (ARC), which showed that LiFePO4 is safer, upon thermal and electrochemical abuse, than the commonly used lithium metal oxide cathodes with layered and spinel structures. Safety tests, such as nail penetration and crush test, were performed on LiFePO4 and LiCoO2 cathode based cells, to investigate on the safety hazards of the cells upon severe physical abuse and damage.

Mechanochemical Synthesis of Li2MnO3 Shell/LiMO2 (M = Ni, Co, Mn) Core-Structured Nanocomposites for Lithium-Ion Batteries

PubMed Central

Noh, Jae-Kyo; Kim, Soo; Kim, Haesik; Choi, Wonchang; Chang, Wonyoung; Byun, Dongjin; Cho, Byung-Won; Chung, Kyung Yoon

2014-01-01

Core/shell-like nanostructured xLi2MnO3·(1−x)LiMO2 (M = Ni, Co, Mn) composite cathode materials are successfully synthesized through a simple solid-state reaction using a mechanochemical ball-milling process. The LiMO2 core is designed to have a high-content of Ni, which increases the specific capacity. The detrimental surface effects arising from the high Ni-content are countered by the Li2MnO3 shell, which stabilizes the nanoparticles. The electrochemical performances and thermal stabilities of the synthesized nanocomposites are compared with those of bare LiMO2. In particular, the results of time-resolved X-ray diffraction (TR-XRD) analyses of xLi2MnO3·(1−x)LiMO2 nanocomposites as well as their differential scanning calorimetry (DSC) profiles demonstrate that the Li2MnO3 shell is effective in stabilizing the LiMO2 core at high temperatures, making the nanocomposites highly suitable from a safety viewpoint. PMID:24784478

Isotope scattering and phonon thermal conductivity in light atom compounds: LiH and LiF

DOE PAGES

Lindsay, Lucas R.

2016-11-08

Engineered isotope variation is a pathway toward modulating lattice thermal conductivity (κ) of a material through changes in phonon-isotope scattering. The effects of isotope variation on intrinsic thermal resistance is little explored, as varying isotopes have relatively small differences in mass and thus do not affect bulk phonon dispersions. However, for light elements isotope mass variation can be relatively large (e.g., hydrogen and deuterium). Using a first principles Peierls-Boltzmann transport equation approach the effects of isotope variance on lattice thermal transport in ultra-low-mass compound materials LiH and LiF are characterized. The isotope mass variance modifies the intrinsic thermal resistance viamore » modulation of acoustic and optic phonon frequencies, while phonon-isotope scattering from mass disorder plays only a minor role. This leads to some unusual cases where values of isotopically pure systems ( 6LiH, 7Li 2H and 6LiF) are lower than the values from their counterparts with naturally occurring isotopes and phonon-isotope scattering. However, these differences are relatively small. The effects of temperature-driven lattice expansion on phonon dispersions and calculated κ are also discussed. This work provides insight into lattice thermal conductivity modulation with mass variation and the interplay of intrinsic phonon-phonon and phonon-isotope scattering in interesting light atom systems.« less

Direct view on the phase evolution in individual LiFePO4 nanoparticles during Li-ion battery cycling.

PubMed

Zhang, Xiaoyu; van Hulzen, Martijn; Singh, Deepak P; Brownrigg, Alex; Wright, Jonathan P; van Dijk, Niels H; Wagemaker, Marnix

2015-09-23

Phase transitions in Li-ion electrode materials during (dis)charge are decisive for battery performance, limiting high-rate capabilities and playing a crucial role in the cycle life of Li-ion batteries. However, the difficulty to probe the phase nucleation and growth in individual grains is hindering fundamental understanding and progress. Here we use synchrotron microbeam diffraction to disclose the cycling rate-dependent phase transition mechanism within individual particles of LiFePO4, a key Li-ion electrode material. At low (dis)charge rates well-defined nanometer thin plate-shaped domains co-exist and transform much slower and concurrent as compared with the commonly assumed mosaic transformation mechanism. As the (dis)charge rate increases phase boundaries become diffuse speeding up the transformation rates of individual grains. Direct observation of the transformation of individual grains reveals that local current densities significantly differ from what has previously been assumed, giving new insights in the working of Li-ion battery electrodes and their potential improvements.

Direct view on the phase evolution in individual LiFePO4 nanoparticles during Li-ion battery cycling

PubMed Central

Zhang, Xiaoyu; van Hulzen, Martijn; Singh, Deepak P.; Brownrigg, Alex; Wright, Jonathan P.; van Dijk, Niels H.; Wagemaker, Marnix

2015-01-01

Phase transitions in Li-ion electrode materials during (dis)charge are decisive for battery performance, limiting high-rate capabilities and playing a crucial role in the cycle life of Li-ion batteries. However, the difficulty to probe the phase nucleation and growth in individual grains is hindering fundamental understanding and progress. Here we use synchrotron microbeam diffraction to disclose the cycling rate-dependent phase transition mechanism within individual particles of LiFePO4, a key Li-ion electrode material. At low (dis)charge rates well-defined nanometer thin plate-shaped domains co-exist and transform much slower and concurrent as compared with the commonly assumed mosaic transformation mechanism. As the (dis)charge rate increases phase boundaries become diffuse speeding up the transformation rates of individual grains. Direct observation of the transformation of individual grains reveals that local current densities significantly differ from what has previously been assumed, giving new insights in the working of Li-ion battery electrodes and their potential improvements. PMID:26395323

Li-Ion Cell Development for Low Temperature Applications

NASA Technical Reports Server (NTRS)

Huang, C.-K.; Sakamoto, J. S.; Surampudi, S.; Wolfenstine, J.

2000-01-01

JPL is involved in the development of rechargeable Li-ion cells for future Mars Exploration Missions. The specific objectives are to improve the Li-ion cell cycle life performance and rate capability at low temperature (<<-20 C) in order to enhance survivability of the Mars lander and rover batteries. Poor Li-ion rate capability at low temperature has been attributed to: (1) the electrolytes becoming viscous or freezing and/or (2) reduced electrode capacity that results from decreased Li diffusivity. Our efforts focus on increasing the rate capability at low temperature for Li-ion cells. In order to improve the rate capability we evaluated the following: (1) cathode performance at low temperatures, (2) electrode active material particle size on low temperature performance and (3) Li diffusivity at room temperature and low temperatures. In this paper, we will discuss the results of our study.

A promising tritium breeding material: Nanostructured 2Li2TiO3-Li4SiO4 biphasic ceramic pebbles

NASA Astrophysics Data System (ADS)

Dang, Chen; Yang, Mao; Gong, Yichao; Feng, Lan; Wang, Hailiang; Shi, Yanli; Shi, Qiwu; Qi, Jianqi; Lu, Tiecheng

2018-03-01

As an advanced tritium breeder material for the fusion reactor blanket of the International Thermonuclear Experimental Reactor (ITER), Li2TiO3-Li4SiO4 biphasic ceramic has attracted widely attention due to its merits. In this paper, the uniform precursor powders were prepared by hydrothermal method, and nanostructured 2Li2TiO3-Li4SiO4 biphasic ceramic pebbles were fabricated by an indirect wet method at the first time. In addition, the composition dependence (x/y) of their microstructure characteristics and mechanical properties were investigated. The results indicated that the crush load of biphasic ceramic pebbles was better than that of single phase ceramic pebbles under identical conditions. The 2Li2TiO3-Li4SiO4 ceramic pebbles have good morphology, small grain size (90 nm), satisfactory crush load (37.8 N) and relative density (81.8 %T.D.), which could be a promising breeding material in the future fusion reactor.

Promoting formation of noncrystalline Li2O2 in the Li-O2 battery with RuO2 nanoparticles.

PubMed

Yilmaz, Eda; Yogi, Chihiro; Yamanaka, Keisuke; Ohta, Toshiaki; Byon, Hye Ryung

2013-10-09

Low electrical efficiency for the lithium-oxygen (Li-O2) electrochemical reaction is one of the most significant challenges in current nonaqueous Li-O2 batteries. Here we present ruthenium oxide nanoparticles (RuO2 NPs) dispersed on multiwalled carbon nanotubes (CNTs) as a cathode, which dramatically increase the electrical efficiency up to 73%. We demonstrate that the RuO2 NPs contribute to the formation of poorly crystalline lithium peroxide (Li2O2) that is coated over the CNT with large contact area during oxygen reduction reaction (ORR). This unique Li2O2 structure can be smoothly decomposed at low potential upon oxygen evolution reaction (OER) by avoiding the energy loss associated with the decomposition of the more typical Li2O2 structure with a large size, small CNT contact area, and insulating crystals.

High-Rate and Long-Term Cycle Stability of Li-S Batteries Enabled by Li2S/TiO2-Impregnated Hollow Carbon Nanofiber Cathodes.

PubMed

Wang, Xinran; Bi, Xuanxuan; Wang, Shaona; Zhang, Yi; Du, Hao; Lu, Jun

2018-05-16

The high theoretical energy density of lithium-sulfur (Li-S) batteries makes them an alternative battery technology to lithium ion batteries. However, Li-S batteries suffer from low sulfur loading, poor charge transport, and dissolution of lithium polysulfide. In our study, we use the lithiated S, Li 2 S, as the cathode material, coupled with electrospun TiO 2 -impregnated hollow carbon nanofibers (TiO 2 -HCFs), which serve as the conductive agent and protective barrier for Li 2 S in Li-S batteries. TiO 2 -HCFs provide much improved electron/ionic conductivity and serve as a physical barrier, which prevents the dissolution of lithium polysulfides. The Li 2 S/TiO 2 -HCF composite delivers a discharge capacity of 851 mA h g Li 2 S -1 at 0.1C and the bilayer TiO 2 -HCFs/Li 2 S/TiO 2 -HCF composite delivers a high specific capacity of 400 mA h g Li 2 S -1 at 5C.

Effect of the Hydrofluoroether Cosolvent Structure in Acetonitrile-Based Solvate Electrolytes on the Li+ Solvation Structure and Li-S Battery Performance.

PubMed

Shin, Minjeong; Wu, Heng-Liang; Narayanan, Badri; See, Kimberly A; Assary, Rajeev S; Zhu, Lingyang; Haasch, Richard T; Zhang, Shuo; Zhang, Zhengcheng; Curtiss, Larry A; Gewirth, Andrew A

2017-11-15

We evaluate hydrofluoroether (HFE) cosolvents with varying degrees of fluorination in the acetonitrile-based solvate electrolyte to determine the effect of the HFE structure on the electrochemical performance of the Li-S battery. Solvates or sparingly solvating electrolytes are an interesting electrolyte choice for the Li-S battery due to their low polysulfide solubility. The solvate electrolyte with a stoichiometric ratio of LiTFSI salt in acetonitrile, (MeCN) 2 -LiTFSI, exhibits limited polysulfide solubility due to the high concentration of LiTFSI. We demonstrate that the addition of highly fluorinated HFEs to the solvate yields better capacity retention compared to that of less fluorinated HFE cosolvents. Raman and NMR spectroscopy coupled with ab initio molecular dynamics simulations show that HFEs exhibiting a higher degree of fluorination coordinate to Li + at the expense of MeCN coordination, resulting in higher free MeCN content in solution. However, the polysulfide solubility remains low, and no crossover of polysulfides from the S cathode to the Li anode is observed.

Effect of the Hydrofluoroether Cosolvent Structure in Acetonitrile-Based Solvate Electrolytes on the Li+ Solvation Structure and Li-S Battery Performance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Minjeong; Wu, Heng-Liang; Narayanan, Badri

We evaluate hydrofluoroether (HFE) cosolvents with varying degrees of fluorination in the acetonitrile-based solvate electrolyte to determine the effect of the HFE structure on the electrochemical performance of the Li-S battery. Solvates or sparingly solvating electrolytes are an interesting electrolyte choice for the Li-S battery due to their low polysulfide solubility. The solvate electrolyte with a stoichiometric ratio of LiTFSI salt in acetonitrile, (MeCN)(2)-LiTFSI, exhibits limited polysulfide solubility due to the high concentration of LiTFSI. We demonstrate that the addition of highly fluorinated HFEs to the solvate yields better capacity retention compared to that of less fluorinated HFE cosolvents. Ramanmore » and NMR spectroscopy coupled with ab initio molecular dynamics simulations show that HFEs exhibiting a higher degree of fluorination coordinate to Li+ at the expense of MeCN coordination, resulting in higher free MeCN content in solution. However, the polysulfide solubility remains low, and no crossover of polysulfides from the S cathode to the Li anode is observed.« less

Nanostructured LiMn2O4 composite as high-rate cathode for high performance aqueous Li-ion hybrid supercapacitors

NASA Astrophysics Data System (ADS)

Chen, Lina; Zhai, Wei; Chen, Long; Li, Deping; Ma, Xiaoxin; Ai, Qing; Xu, Xiaoyan; Hou, Guangmei; Zhang, Lin; Feng, Jinkui; Si, Pengchao; Ci, Lijie

2018-07-01

Nanostructured spinel LiMn2O4 and super P composite with much enhanced electrochemical performance especially ultrahigh rate capability as the cathode for aqueous hybrid supercapacitors is synthesized by ball milling commercial LiMn2O4 particles together with super P. The as-prepared composite delivers a high capacitance of 306 F g-1 at the current density of 1 A g-1 and superb rate ability of 228.6 F g-1 at 40 A g-1 in 1 M Li2SO4 aqueous electrolyte. The capacitance of the nanostructured composite is 3.5 times higher than that of pristine LiMn2O4 even being charged and discharged 80 times faster. The excellent performances are ascribed to the nanosized LiMn2O4 well dispersed into the conductive carbon matrix. LiMn2O4 and super P composite//active carbon hybrid supercapacitor is assembled and the energy density can reach up to 21.58 Wh kg-1 at 293.16 W kg-1 and 13 Wh kg-1 at 5200 W kg-1. The hybrid device also shows an excellent cycling performance, which retains 85% of the initial capacitance after 4500 cycles. This work provides an effectively facile way to produce high performance LiMn2O4-based cathodes for hybrid suercapacitors in practical applications.

Potassium Ions Promote Solution-Route Li2O2 Formation in the Positive Electrode Reaction of Li-O2 Batteries.

PubMed

Matsuda, Shoichi; Kubo, Yoshimi; Uosaki, Kohei; Nakanishi, Shuji

2017-03-16

Lithium-oxygen system has attracted much attention as a battery with high energy density that could satisfy the demands for electric vehicles. However, because lithium peroxide (Li 2 O 2 ) is formed as an insoluble and insulative discharge product at the positive electrode, Li-O 2 batteries have poor energy capacities. Although Li 2 O 2 deposition on the positive electrode can be avoided by inducing solution-route pathway using electrolytes composed of high donor number (DN) solvents, such systems generally have poor stability. Herein we report that potassium ions promote the solution-route formation of Li 2 O 2 . The present findings suggest that potassium or other monovalent ions have the potential to increase the volumetric energy density and life cycles of Li-O 2 batteries.

Relating the 3D electrode morphology to Li-ion battery performance; a case for LiFePO4

NASA Astrophysics Data System (ADS)

Liu, Zhao; Verhallen, Tomas W.; Singh, Deepak P.; Wang, Hongqian; Wagemaker, Marnix; Barnett, Scott

2016-08-01

One of the main goals in lithium ion battery electrode design is to increase the power density. This requires insight in the relation between the complex heterogeneous microstructure existing of active material, conductive additive and electrolyte providing the required electronic and Li-ion transport. FIB-SEM is used to determine the three phase 3D morphology, and Li-ion concentration profiles obtained with Neutron Depth Profiling (NDP) are compared for two cases, conventional LiFePO4 electrodes and better performing carbonate templated LiFePO4 electrodes. This provides detailed understanding of the impact of key parameters such as the tortuosity for electron and Li-ion transport though the electrodes. The created hierarchical pore network of the templated electrodes, containing micron sized pores, appears to be effective only at high rate charge where electrolyte depletion is hindering fast discharge. Surprisingly the carbonate templating method results in a better electronic conductive CB network, enhancing the activity of LiFePO4 near the electrolyte-electrode interface as directly observed with NDP, which in a large part is responsible for the improved rate performance both during charge and discharge. The results demonstrate that standard electrodes have a far from optimal charge transport network and that significantly improved electrode performance should be possible by engineering the microstructure.

Garnet Electrolyte with an Ultralow Interfacial Resistance for Li-Metal Batteries.

PubMed

Li, Yutao; Chen, Xi; Dolocan, Andrei; Cui, Zhiming; Xin, Sen; Xue, Leigang; Xu, Henghui; Park, Kyusung; Goodenough, John B

2018-05-23

Garnet-structured Li 7 La 3 Zr 2 O 12 is a promising solid Li-ion electrolyte for all-solid-state Li-metal batteries and Li-redox-flow batteries owing to its high Li-ion conductivity at room temperature and good electrochemical stability with Li metal. However, there are still three major challenges unsolved: (1) the controversial electrochemical window of garnet, (2) the impractically large resistance at a garnet/electrode interface and the fast lithium-dendrite growth along the grain boundaries of the garnet pellet, and (3) the fast degradation during storage. We have found that these challenges are closely related to a thick Li 2 CO 3 layer and the Li-Al-O glass phase on the surface of garnet materials. Here we introduce a simple method to remove Li 2 CO 3 and the protons in the garnet framework by reacting garnet with carbon at 700 °C; moreover, the amount of the Li-Al-O glass phase with a low Li-ion conductivity in the grain boundary on the garnet surface was also reduced. The surface of the carbon-treated garnet pellets is free of Li 2 CO 3 and is wet by a metallic lithium anode, an organic electrolyte, and a solid composite cathode. The carbon post-treatment has reduced significantly the interfacial resistances to 28, 92 (at 65 °C), and 45 Ω cm 2 at Li/garnet, garnet/LiFePO 4 , and garnet/organic-liquid interfaces, respectively. A symmetric Li/garnet/Li, an all-solid-state Li/garnet/LiFePO 4 , and a hybrid Li-S cell show small overpotentials, high Coulombic efficiencies, and stable cycling performance.

Tracing Waste Water with Li isotopes

NASA Astrophysics Data System (ADS)

Millot, R.; Desaulty, A. M.

2015-12-01

The contribution of human activities such as industries, agriculture and various domestic inputs, becomes more and more significant in the chemical composition of the dissolved load of rivers. Human factors act as a supplementary key process. Therefore the mass-balance for the budget of catchments and river basins include anthropogenic disturbances. In the present study, we investigate waste water tracing by the use of Li isotopes in a small river basin near Orléans in France (l'Egoutier, 15 km² and 5 km long). It is well known that Li has strategic importance for numerous industrial applications including its use in the production of batteries for both mobile devices (computers, tablets, smartphones, etc.) and electric vehicles, but also in pharmaceutical formulations. In the present work, we collected river waters samples before and after the release from a waste water treatment plant connected to an hospital. Lithium isotopic compositions are rather homogeneous in river waters with δ7Li values around -0.5‰ ± 1 along the main course of the stream (n=7). The waste water sample is very different from the natural background of the river basin with Li concentration being twice of the values without pollution and significant heavy lithium contribution (δ7Li = +4‰). These preliminary results will be discussed in relation with factors controlling the distribution of Li and its isotopes in this specific system and compared with the release of other metals such as Pb or Zn.

Device fabrication, characterization, and thermal neutron detection response of LiZnP and LiZnAs semiconductor devices

NASA Astrophysics Data System (ADS)

Montag, Benjamin W.; Ugorowski, Philip B.; Nelson, Kyle A.; Edwards, Nathaniel S.; McGregor, Douglas S.

2016-11-01

Nowotny-Juza compounds continue to be explored as candidates for solid-state neutron detectors. Such a device would have greater efficiency, in a compact form, than present day gas-filled 3He and 10BF3 detectors. The 6Li(n,t)4He reaction yields a total Q-value of 4.78 MeV, larger than 10B, an energy easily identified above background radiations. Hence, devices fabricated from semiconductor compounds having either natural Li (nominally 7.5% 6Li) or enriched 6Li (usually 95% 6Li) as constituent atoms may provide a material for compact high efficiency neutron detectors. Starting material was synthesized by preparing equimolar portions of Li, Zn, and As sealed under vacuum (10-6 Torr) in quartz ampoules lined with boron nitride and subsequently reacted in a compounding furnace [1]. The raw synthesized material indicated the presence high impurity levels (material and electrical property characterizations). A static vacuum sublimation in quartz was performed to help purify the synthesized material [2,3]. Bulk crystalline samples were grown from the purified material [4,5]. Samples were cut using a diamond wire saw, and processed into devices. Bulk resistivity was determined from I-V curve measurements, ranging from 106-1011 Ω cm. Devices were characterized for sensitivity to 5.48 MeV alpha particles, 337 nm laser light, and neutron sensitivity in a thermal neutron diffracted beam at the Kansas State University TRIGA Mark II nuclear reactor. Thermal neutron reaction product charge induction was measured with a LiZnP device, and the reaction product spectral response was observed.

Genetics Home Reference: Li-Fraumeni syndrome

MedlinePlus

... are some genetic conditions more common in particular ethnic groups? Genetic Changes The CHEK2 and TP53 genes are associated with Li-Fraumeni syndrome . More than half of all families with Li-Fraumeni syndrome have inherited mutations in ...

Experimental simulation of internal short circuit in Li-ion and Li-ion-Polymer cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Wei; Wang, Hsin; Maleki, Hossein

A multi-parameter controlled pinch test was developed to study the occurrence of internal short circuits in Li-ion and Li-ion-polymer cells. By tuning the control parameters (i.e., cell voltage as well as pinching area, load, and speed), the pinch test can reproducibly create ~1 to 2 mm wide internal short between a cell jelly-roll s inner layer electrodes. This recreates conditions similar to those that may occur during service. Furthermore, the pinch test is used to determine thermal stability of two Li-ion-polymer cells of different designs built by the same manufacturer. The pinch test method can be used to help distinguishmore » cells with design features or characteristics that lower risk of potential thermal events created by internal short circuits.« less

Polymer-ionic liquid ternary systems for Li-battery electrolytes: Molecular dynamics studies of LiTFSI in a EMIm-TFSI and PEO blend

NASA Astrophysics Data System (ADS)

Costa, Luciano T.; Sun, Bing; Jeschull, Fabian; Brandell, Daniel

2015-07-01

This paper presents atomistic molecular dynamics simulation studies of lithium bis(trifluoromethane)sulfonylimide (LiTFSI) in a blend of 1-ethyl-3-methylimidazolium (EMIm)-TFSI and poly(ethylene oxide) (PEO), which is a promising electrolyte material for Li- and Li-ion batteries. Simulations of 100 ns were performed for temperatures between 303 K and 423 K, for a Li:ether oxygen ratio of 1:16, and for PEO chains with 26 EO repeating units. Li+ coordination and transportation were studied in the ternary electrolyte system, i.e., PEO16LiTFSIṡ1.0 EMImTFSI, by applying three different force field models and are here compared to relevant simulation and experimental data. The force fields generated significantly different results, where a scaled charge model displayed the most reasonable comparisons with previous work and overall consistency. It is generally seen that the Li cations are primarily coordinated to polymer chains and less coupled to TFSI anion. The addition of EMImTFSI in the electrolyte system enhances Li diffusion, associated to the enhanced TFSI dynamics observed when increasing the overall TFSI anion concentration in the polymer matrix.

Polymer-ionic liquid ternary systems for Li-battery electrolytes: Molecular dynamics studies of LiTFSI in a EMIm-TFSI and PEO blend.

PubMed

Costa, Luciano T; Sun, Bing; Jeschull, Fabian; Brandell, Daniel

2015-07-14

This paper presents atomistic molecular dynamics simulation studies of lithium bis(trifluoromethane)sulfonylimide (LiTFSI) in a blend of 1-ethyl-3-methylimidazolium (EMIm)-TFSI and poly(ethylene oxide) (PEO), which is a promising electrolyte material for Li- and Li-ion batteries. Simulations of 100 ns were performed for temperatures between 303 K and 423 K, for a Li:ether oxygen ratio of 1:16, and for PEO chains with 26 EO repeating units. Li(+) coordination and transportation were studied in the ternary electrolyte system, i.e., PEO16LiTFSI⋅1.0 EMImTFSI, by applying three different force field models and are here compared to relevant simulation and experimental data. The force fields generated significantly different results, where a scaled charge model displayed the most reasonable comparisons with previous work and overall consistency. It is generally seen that the Li cations are primarily coordinated to polymer chains and less coupled to TFSI anion. The addition of EMImTFSI in the electrolyte system enhances Li diffusion, associated to the enhanced TFSI dynamics observed when increasing the overall TFSI anion concentration in the polymer matrix.

Polymer-ionic liquid ternary systems for Li-battery electrolytes: Molecular dynamics studies of LiTFSI in a EMIm-TFSI and PEO blend

DOE Office of Scientific and Technical Information (OSTI.GOV)

Costa, Luciano T., E-mail: ltcosta@id.uff.br; Sun, Bing; Jeschull, Fabian

2015-07-14

This paper presents atomistic molecular dynamics simulation studies of lithium bis(trifluoromethane)sulfonylimide (LiTFSI) in a blend of 1-ethyl-3-methylimidazolium (EMIm)-TFSI and poly(ethylene oxide) (PEO), which is a promising electrolyte material for Li- and Li-ion batteries. Simulations of 100 ns were performed for temperatures between 303 K and 423 K, for a Li:ether oxygen ratio of 1:16, and for PEO chains with 26 EO repeating units. Li{sup +} coordination and transportation were studied in the ternary electrolyte system, i.e., PEO{sub 16}LiTFSI⋅1.0 EMImTFSI, by applying three different force field models and are here compared to relevant simulation and experimental data. The force fields generatedmore » significantly different results, where a scaled charge model displayed the most reasonable comparisons with previous work and overall consistency. It is generally seen that the Li cations are primarily coordinated to polymer chains and less coupled to TFSI anion. The addition of EMImTFSI in the electrolyte system enhances Li diffusion, associated to the enhanced TFSI dynamics observed when increasing the overall TFSI anion concentration in the polymer matrix.« less

Charging a Li-O₂ battery using a redox mediator.

PubMed

Chen, Yuhui; Freunberger, Stefan A; Peng, Zhangquan; Fontaine, Olivier; Bruce, Peter G

2013-06-01

The non-aqueous Li-air (O2) battery is receiving intense interest because its theoretical specific energy exceeds that of Li-ion batteries. Recharging the Li-O2 battery depends on oxidizing solid lithium peroxide (Li2O2), which is formed on discharge within the porous cathode. However, transporting charge between Li2O2 particles and the solid electrode surface is at best very difficult and leads to voltage polarization on charging, even at modest rates. This is a significant problem facing the non-aqueous Li-O2 battery. Here we show that incorporation of a redox mediator, tetrathiafulvalene (TTF), enables recharging at rates that are impossible for the cell in the absence of the mediator. On charging, TTF is oxidized to TTF(+) at the cathode surface; TTF(+) in turn oxidizes the solid Li2O2, which results in the regeneration of TTF. The mediator acts as an electron-hole transfer agent that permits efficient oxidation of solid Li2O2. The cell with the mediator demonstrated 100 charge/discharge cycles.

Laser performance of in-band pumped Er : LiYF{sub 4} and Er : LiLuF{sub 4} crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorbachenya, K N; Kisel, V E; Yasukevich, A S

2016-02-28

Spectroscopic properties of Er : LiLuF{sub 4} and Er : LiYF{sub 4} crystals in the spectral region near 1.5 μm and the lasing characteristics of these crystals under in-band pumping at a wavelength of 1522 nm are studied. With the Er : LiLuF{sub 4} crystal, the maximum slope efficiency with respect to the absorbed pump power was 44% at a wavelength of 1609 nm. Continuous-wave operation of an inband pumped Er : LiYF{sub 4} laser is obtained for the first time. The output power at a wavelength of 1606 nm was 58 mW with a slope efficiency of 21%. (lasers)

Riverine Li isotope fractionation in small mountainous rivers of Taiwan

NASA Astrophysics Data System (ADS)

Huang, K. F.; Liu, Y. H.; Wang, R. M.; Chung, C. H.; You, C. F.

2016-12-01

Riverine lithium (Li) and its isotopes became of increasing interest over the last decade due to its great potential as a tracer for silicate weathering processes and carbon cycle. However, little is known about the main controls on the riverine Li isotope fractionation in tropical small mountainous rivers (SMRs). Here we condcut the first deatiled study of the Li isotopic composition (δ7Li) of river-borne dissolved and solid materials in the SMRs around Taiwan to characterize behaviors of riverine Li and δ7Li in different geomorrphic setting and at wet/dry seasons. Riverine Li and δ7Li range from 0.15 to 6.37 μM with δ7Li of +8.6 to +18.2 ‰ at the wet season, and 0.23 to 18.8 μM with δ7Li of +8.2 to +20.3 ‰ at the dry season. Of special interest is that high dissolved δ7Li values are observed at the wet season and the downstream of the river catchments. By combining the multiple isotope systems and river chemistry, our results suggest that in the high-relief and tectonically active terrain, the high δ7Li values at the wet season are most likely controlled by more intense chemcical weathering, particularly by the greater extent of uptake of 6Li into secondary minierals during weathering. Seasonal variations in the dissolved loads and riverine δ7Li are also found and can be attributed to a greater contribution from carbonate weathering at the wet season, highlighting a different response of primary mineral dissolution/secondary mineral formation to climatic forcing in the SMRs of Taiwan.

Study of Li atom diffusion in amorphous Li3PO4 with neural network potential

NASA Astrophysics Data System (ADS)

Li, Wenwen; Ando, Yasunobu; Minamitani, Emi; Watanabe, Satoshi

2017-12-01

To clarify atomic diffusion in amorphous materials, which is important in novel information and energy devices, theoretical methods having both reliability and computational speed are eagerly anticipated. In the present study, we applied neural network (NN) potentials, a recently developed machine learning technique, to the study of atom diffusion in amorphous materials, using Li3PO4 as a benchmark material. The NN potential was used together with the nudged elastic band, kinetic Monte Carlo, and molecular dynamics methods to characterize Li vacancy diffusion behavior in the amorphous Li3PO4 model. By comparing these results with corresponding DFT calculations, we found that the average error of the NN potential is 0.048 eV in calculating energy barriers of diffusion paths, and 0.041 eV in diffusion activation energy. Moreover, the diffusion coefficients obtained from molecular dynamics are always consistent with those from ab initio molecular dynamics simulation, while the computation speed of the NN potential is 3-4 orders of magnitude faster than DFT. Lastly, the structure of amorphous Li3PO4 and the ion transport properties in it were studied with the NN potential using a large supercell model containing more than 1000 atoms. The formation of P2O7 units was observed, which is consistent with the experimental characterization. The Li diffusion activation energy was estimated to be 0.55 eV, which agrees well with the experimental measurements.

Evidence for anionic redox activity in a tridimensional-ordered Li-rich positive electrode β-Li2IrO3.

PubMed

Pearce, Paul E; Perez, Arnaud J; Rousse, Gwenaelle; Saubanère, Mathieu; Batuk, Dmitry; Foix, Dominique; McCalla, Eric; Abakumov, Artem M; Van Tendeloo, Gustaaf; Doublet, Marie-Liesse; Tarascon, Jean-Marie

2017-05-01

Lithium-ion battery cathode materials have relied on cationic redox reactions until the recent discovery of anionic redox activity in Li-rich layered compounds which enables capacities as high as 300 mAh g -1 . In the quest for new high-capacity electrodes with anionic redox, a still unanswered question was remaining regarding the importance of the structural dimensionality. The present manuscript provides an answer. We herein report on a β-Li 2 IrO 3 phase which, in spite of having the Ir arranged in a tridimensional (3D) framework instead of the typical two-dimensional (2D) layers seen in other Li-rich oxides, can reversibly exchange 2.5 e - per Ir, the highest value ever reported for any insertion reaction involving d-metals. We show that such a large activity results from joint reversible cationic (M n+ ) and anionic (O 2 ) n- redox processes, the latter being visualized via complementary transmission electron microscopy and neutron diffraction experiments, and confirmed by density functional theory calculations. Moreover, β-Li 2 IrO 3 presents a good cycling behaviour while showing neither cationic migration nor shearing of atomic layers as seen in 2D-layered Li-rich materials. Remarkably, the anionic redox process occurs jointly with the oxidation of Ir 4+ at potentials as low as 3.4 V versus Li + /Li 0 , as equivalently observed in the layered α-Li 2 IrO 3 polymorph. Theoretical calculations elucidate the electrochemical similarities and differences of the 3D versus 2D polymorphs in terms of structural, electronic and mechanical descriptors. Our findings free the structural dimensionality constraint and broaden the possibilities in designing high-energy-density electrodes for the next generation of Li-ion batteries.

Infrastructure Investment Protection with LiDAR

DOT National Transportation Integrated Search

2012-10-15

The primary goal of this research effort was to explore the wide variety of uses of LiDAR technology and to evaluate their : applicability to NCDOT practices. NCDOT can use this information about LiDAR in determining how and when the : technology can...

Si(Li) X-ray astronomical spectroscopy

NASA Technical Reports Server (NTRS)

Holt, S. S.

1975-01-01

The general considerations involved in the choice of Si(Li) as a non-dispersive spectrometer for X-ray astronomy are discussed. In particular, its adaptation to HEAO-B is described as an example of the space-borne application of Si(Li) technology.

LiDAR for Air Quality Measurements

DOT National Transportation Integrated Search

2017-02-02

The overall goal of this research is to investigate a unique light detection and ranging (LiDAR) technology for ambient air quality measurement of particulate matter. The ODU team has recently received a state-of-the-art elastic LiDAR from NASA Langl...

Extraction of Li and Co from Li-ion Batteries by Chemical Methods

NASA Astrophysics Data System (ADS)

Guzolu, Jafar Sharrivar; Gharabaghi, Mahdi; Mobin, Mohammad; Alilo, Hojat

2017-04-01

In this work a process involving ultrasonic washing and leaching and precipitation was used to recover Li and Co from spent Li-ion batteries. Ultrasonic washing was used to reduce energy consumption and pollution whereas hydrochloric acid was used as leaching reagent. 98 % of Li and nearly 99 % of Co were obtained under optimum condition of 5 M hydrochloric acid solution, temperature of 95 °C, reaction time of 70 min, and solid-liquid ratio of 10 g/L. In this process at first nickel, copper, iron, aluminum, cobalt, and manganese were precipitated from leaching solution using sodium hydroxide at pH f 12.5 and reaction time of 1 h and temperature was 55 °C and all metal recoveries were more than 99 %. In the precipitation experiments, lithium loss was only 18.34 %. In the next stage, white lithium carbonate was precipitated by addition of saturated sodium carbonate solution to the left filtrate from first precipitation step. The purity of the recovered powder of lithium was 95 %.

Quantum-Chemical Approach to NMR Chemical Shifts in Paramagnetic Solids Applied to LiFePO4 and LiCoPO4.

PubMed

Mondal, Arobendo; Kaupp, Martin

2018-04-05

A novel protocol to compute and analyze NMR chemical shifts for extended paramagnetic solids, accounting comprehensively for Fermi-contact (FC), pseudocontact (PC), and orbital shifts, is reported and applied to the important lithium ion battery cathode materials LiFePO 4 and LiCoPO 4 . Using an EPR-parameter-based ansatz, the approach combines periodic (hybrid) DFT computation of hyperfine and orbital-shielding tensors with an incremental cluster model for g- and zero-field-splitting (ZFS) D-tensors. The cluster model allows the use of advanced multireference wave function methods (such as CASSCF or NEVPT2). Application of this protocol shows that the 7 Li shifts in the high-voltage cathode material LiCoPO 4 are dominated by spin-orbit-induced PC contributions, in contrast with previous assumptions, fundamentally changing interpretations of the shifts in terms of covalency. PC contributions are smaller for the 7 Li shifts of the related LiFePO 4 , where FC and orbital shifts dominate. The 31 P shifts of both materials finally are almost pure FC shifts. Nevertheless, large ZFS contributions can give rise to non-Curie temperature dependences for both 7 Li and 31 P shifts.

Synthèse et étude structrale de lyonsite-type (Na0,4,Li0,6)(Fe,Li2)(MoO4)3

PubMed Central

Souilem, Amira; Zid, Mohamed Faouzi; Driss, Ahmed

2015-01-01

The new compound (Na0.4,Li0.6)(Fe,Li2)(MoO4)3 was synthesized by cooling from the melt. Its anionic framework is built up from two distinct MO6 octa­hedra, each containing disordered Li+ and Fe3+ ions in 0.6:0.4 and 0.7:0.3 ratios, and two MoO4 tetra­hedra, which link by vertex-sharing of their O atoms. These tetra­meric units are further linked by sharing edges between octa­hedra and by formation of M—O—Mo (M = Fe/Li) bridges, forming ribbons propagating in the [100] direction. The ribbons are cross-linked in both the b- and c-axis directions, giving rise to a three-dimensional framework having [100] tunnels in which the monovalent Na+/Li+ cations (0.4:0.6 ratio) lie. Bond-valence calculations are consistent with the disorder model for the cations. The structure of the title compound, which is isotypic with Li3Fe(MoO4)3 and Li3Ga(MoO4)3, is compared briefly with those of LiFeMo2O8 and Li1.6Mn2.2(MoO4)3. PMID:26090130

LiDAR - An emerging tool for geological applications

USGS Publications Warehouse

Stoker, Jason M.

2012-01-01

Over the past five to ten years the use and applicability of light detection and ranging (LiDAR) technology has increased dramatically. As a result, more and more LiDAR data now are being collected across the country for a wide range of applications, and LiDAR currently is the technology of choice for high resolution terrain model creation, 3-D city and infrastructure modeling, forestry, and a wide range of scientific applications. LiDAR is a key technology for geological applications both within and outside the U.S. Geological Survey, and efforts are underway to try to collect high resolution LiDAR data for the entire United States (https://pubs.usgs.gov/fs/2012/3089/pdf/fs2012-3089.pdf).

Electronic structures of superionic conductor Li3N

NASA Astrophysics Data System (ADS)

Aoki, Masaru; Ode, Yoshiyuki; Tsumuraya, Kazuo

2011-03-01

Lithium nitride is a superionic conductor with high Li conductivity. The compound has been studied extensively because of its potential utility as electrolyte in solid-state batteries. Though the mobility of the cations within the crystalline solid is high comparable to that of molten salts, the mechanism of the high mobility of the cations remains unsolved. To clarify the origin of the mobility we investigate the electronic states of the Li cations in the Li 3 N crystal with the first principles electronic structure analysis, focusing a correlation between the cations and the ionicities of the constituent atoms. We have found the existence of the covalent bonding between the Li atoms in the Li 3 N crystal in spite of the ionized states of the constituent atoms.

Femtosecond Cr:LiSAF and Cr:LiCAF lasers pumped by tapered diode lasers.

PubMed

Demirbas, Umit; Schmalz, Michael; Sumpf, Bernd; Erbert, Götz; Petrich, Gale S; Kolodziejski, Leslie A; Fujimoto, James G; Kärtner, Franz X; Leitenstorfer, Alfred

2011-10-10

We report compact, low-cost and efficient Cr:Colquiriite lasers that are pumped by high brightness tapered laser diodes. The tapered laser diodes provided 1 to 1.2 W of output power around 675 nm, at an electrical-to-optical conversion efficiency of about 30%. Using a single tapered diode laser as the pump source, we have demonstrated output powers of 500 mW and 410 mW together with slope efficiencies of 47% and 41% from continuous wave (cw) Cr:LiSAF and Cr:LiCAF lasers, respectively. In cw mode-locked operation, sub-100-fs pulse trains with average power between 200 mW and 250 mW were obtained at repetition rates around 100 MHz. Upon pumping the Cr:Colquiriite lasers with two tapered laser diodes (one from each side of the crystal), we have observed scaling of cw powers to 850 mW in Cr:LiSAF and to 650 mW in Cr:LiCAF. From the double side pumped Cr:LiCAF laser, we have also obtained ~220 fs long pulses with 5.4 nJ of pulse energy at 77 MHz repetition rate. These are the highest energy levels reported from Cr:Colquiriite so far at these repetition rates. Our findings indicate that tapered diodes in the red spectral region are likely to become the standard pump source for Cr:Colquiriite lasers in the near future. Moreover, the simplified pumping scheme might facilitate efficient commercialization of Cr:Colquiriite systems, bearing the potential to significantly boost applications of cw and femtosecond lasers in this spectral region (750-1000 nm).

Devaney chaos, Li-Yorke chaos, and multi-dimensional Li-Yorke chaos for topological dynamics

NASA Astrophysics Data System (ADS)

Dai, Xiongping; Tang, Xinjia

2017-11-01

Let π : T × X → X, written T↷π X, be a topological semiflow/flow on a uniform space X with T a multiplicative topological semigroup/group not necessarily discrete. We then prove: If T↷π X is non-minimal topologically transitive with dense almost periodic points, then it is sensitive to initial conditions. As a result of this, Devaney chaos ⇒ Sensitivity to initial conditions, for this very general setting. Let R+↷π X be a C0-semiflow on a Polish space; then we show: If R+↷π X is topologically transitive with at least one periodic point p and there is a dense orbit with no nonempty interior, then it is multi-dimensional Li-Yorke chaotic; that is, there is a uncountable set Θ ⊆ X such that for any k ≥ 2 and any distinct points x1 , … ,xk ∈ Θ, one can find two time sequences sn → ∞ ,tn → ∞ with Moreover, let X be a non-singleton Polish space; then we prove: Any weakly-mixing C0-semiflow R+↷π X is densely multi-dimensional Li-Yorke chaotic. Any minimal weakly-mixing topological flow T↷π X with T abelian is densely multi-dimensional Li-Yorke chaotic. Any weakly-mixing topological flow T↷π X is densely Li-Yorke chaotic. We in addition construct a completely Li-Yorke chaotic minimal SL (2 , R)-acting flow on the compact metric space R ∪ { ∞ }. Our various chaotic dynamics are sensitive to the choices of the topology of the phase semigroup/group T.

New generation Li+ NASICON glass-ceramics for solid state Li+ ion battery applications

NASA Astrophysics Data System (ADS)

Sharma, Neelakshi; Dalvi, Anshuman

2018-04-01

Lithiumion conducting NASICON glass-ceramics have been prepared by a novel planetary ball milling assisted synthesis route. Structural, thermal and electrical investigations have been carried out on the novel composites composed of LiTi(PO4)3 (LTP) and 50[Li2SO4]-50[Li2O-P2O5] ionic glass reveal interesting results. Composites were prepared keeping the concentration of the ionic glass fixed at 20 wt%. X-ray diffraction and diffe rential thermal analysis confirm the glass-ceramic formation. Moreover, the structure of LTP remains intact during the glass -ceramic formation. Electrical conductivity of the glass-ceramic composite is found to be higher than that of the pristine glass (50LSLP) and LTP. The bulk and grain boundary conductivities of LTP exhibit improvement in composite. Owing to high ionic conductivity and thermal stability, novel glass -ceramic seems to be a promising candidate for all solid-state battery applications.

Neutron detection with LiInSe2

NASA Astrophysics Data System (ADS)

Bell, Zane W.; Burger, A.; Matei, Liviu; Groza, Michael; Stowe, Ashley; Tower, Joshua; Kargar, Alireza; Hong, Huicong

2015-08-01

The detection of thermal neutrons has traditionally been accomplished with 3He-tubes, but with the recent shortage of 3He, much research has gone into finding suitable replacements. Both relatively inefficient 10B- and 6LiF-coated silicon diodes and HgI2 have been known for many years, and engineered structures in Si that have been filled with 10B and 6LiF have shown promise. These devices are intended to realize an optimal juxtaposition of neutron-sensitive material and semiconductor and thereby simulate a semiconductor containing B or Li. Such material has been realized for the first time in the form of 6LiInSe2 in which collectable charge from the 6Li(n,t) reaction indicates a neutron event. In this paper we report neutron and gamma responses of 6LiInSe2, we show pulse height spectra from pure gamma sources and from a thermal neutron source, and we derive the μτ product from the position of spectral features as a function of bias voltage. In addition, we demonstrate the observation of the beta decay of 116mIn in samples exposed to thermal neutrons. This feature of the response serves as an additional confirmation of exposure to neutrons.

First-principles calculated decomposition pathways for LiBH 4 nanoclusters

DOE PAGES

Huang, Zhi -Quan; Chen, Wei -Chih; Chuang, Feng -Chuan; ...

2016-05-18

Here, we analyze thermodynamic stability and decomposition pathways of LiBH 4 nanoclusters using grand-canonical free-energy minimization based on total energies and vibrational frequencies obtained from density-functional theory (DFT) calculations. We consider (LiBH 4) n nanoclusters with n = 2 to 12 as reactants, while the possible products include (Li) n, (B) n, (LiB) n, (LiH) n, and Li 2B nH n; off-stoichiometric LinBnHm (m ≤ 4n) clusters were considered for n = 2, 3, and 6. Cluster ground-state configurations have been predicted using prototype electrostatic ground-state (PEGS) and genetic algorithm (GA) based structural optimizations. Free-energy calculations show hydrogen release pathwaysmore » markedly differ from those in bulk LiBH 4. While experiments have found that the bulk material decomposes into LiH and B, with Li 2B 12H 12 as a kinetically inhibited intermediate phase, (LiBH 4) n nanoclusters with n ≤ 12 are predicted to decompose into mixed Li nB n clusters via a series of intermediate clusters of Li nB nH m (m ≤ 4n). The calculated pressure-composition isotherms and temperature-pressure isobars exhibit sloping plateaus due to finite size effects on reaction thermodynamics. Generally, decomposition temperatures of free-standing clusters are found to increase with decreasing cluster size due to thermodynamic destabilization of reaction products.« less

Ultraviolet-infrared laser-induced domain inversion in MgO-doped congruent LiNbO3 and near stoichiometric LiTaO3 crystals

NASA Astrophysics Data System (ADS)

Zhi, Ya'nan; Qu, Weijuan; Liu, De'an; Sun, Jianfeng; Yan, Aimin; Liu, Liren

2008-08-01

Laser-induced domain inversion is a promising technique for domain engineering in LiNbO3 and LiTaO3. The ultraviolet-infrared laser induced domain inversions in MgO-doped congruent LiNbO3 and near stoichiometric LiTaO3 crystals are investigated for the first time here. Within the wavelength range from 351 to 799 nm, the different reductions of nucleation field induced by the focused continuous laser irradiation are systematically investigated in the MgO-doped congruent LiNbO3 crystals. The investigation of ultrashort-pulse laser-induced domain inversion in MgO-doped congruent LiNbO3 is performed with 800 nm wavelength irradiation. The focused continuous ultraviolet laser-induced ferroelectric domain inversion in the near stoichiometric LiTaO3 is also investigated. The different physical explanations, based on space charge field and defect formation, are presented for the laser-induced domain inversion, and the solid experimental proofs are also presented. The results provide the solid experimental proofs and feasible schemes for the further investigation of laser-induced domain engineering in MgO-doped LiNbO3 and near stoichiometric LiTaO3 crystals. The important characteristics of domain inversion, including domain wall and internal field, in LiNbO3 crystals are also investigated by the digital holographic interferometry with an improved reconstruction method, and some creative experimental results and conclusions are achieved.

Li 2OHCl crystalline electrolyte for stable metallic lithium anodes

DOE PAGES

Hood, Zachary D.; Wang, Hui; Samuthira Pandian, Amaresh; ...

2016-01-22

In a classic example of stability from instability, we show that Li 2OHCl solid electrolyte forms a stable solid electrolyte interface (SEI) with metallic lithium anode. The Li 2OHCl solid electrolyte can be readily achieved through simple mixing of air-stable LiOH and LiCl precursors with a mild processing temperature under 400 °C. Additionally, we show that continuous, dense Li 2OHCl membranes can be fabricated at temperatures less than 400 °C, standing in great contrast to current processing temperatures of over 1600 °C for most oxide-based solid electrolytes. The ionic conductivity and Arrhenius activation energy were explored for the LiOH-LiCl systemmore » of crystalline solid electrolytes where Li 2OHCl with increased crystal defects was found to have the highest ionic conductivity and reasonable Arrhenius activation energy. The Li 2OHCl solid electrolyte displays stability against metallic lithium, even in extreme conditions past the melting point of lithium metal. Furthermore, to understand this excellent stability, we show that SEI formation is critical in stabilizing the interface between metallic lithium and the Li 2OHCl solid electrolyte.« less

Li Isotope Studies of Olivine in Mantle Xenoliths by SIMS

NASA Technical Reports Server (NTRS)

Bell, D. R.; Hervig, R. L.; Buseck, P. R.

2005-01-01

Variations in the ratio of the stable isotopes of Li are a potentially powerful tracer of processes in planetary and nebular environments [1]. Large differences in the 7Li/6Li ratio between the terrestrial upper mantle and various crustal materials make Li isotope composition a potentially powerful tracer of crustal recycling processes on Earth [2]. Recent SIMS studies of terrestrial mantle and Martian meteorite samples report intra-mineral Li isotope zoning [3-5]. Substantial Li isotope heterogeneity also exists within and between the components of chondritic meteorites [6,7]. Experimental studies of Li diffusion suggest the potential for rapid isotope exchange at elevated temperatures [8]. Large variations in 7Li, exceeding the range of unaltered basalts, occur in terrestrial mantle-derived xenoliths from individual localities [9]. The origins of these variations are not fully understood.

Core-shell Li2S@Li3PS4 nanoparticles incorporated into graphene aerogel for lithium-sulfur batteries with low potential barrier and overpotential

NASA Astrophysics Data System (ADS)

Jiao, Zheng; Chen, Lu; Si, Jian; Xu, Chuxiong; Jiang, Yong; Zhu, Ying; Yang, Yaqing; Zhao, Bing

2017-06-01

Lithium sulfide as a promising cathode material not only have a high theoretical specific capacity, but also can be paired with Li-free anode material to avoid potential safety issues. However, how to prepare high electrochemical performance material is still challenge. Herein, we present a facile way to obtain high crystal quality Li2S nanomaterials with average particle size of about 55 nm and coated with Li3PS4 to form the nano-scaled core-shell Li2S@Li3PS4 composite. Then nano-Li2S@Li3PS4/graphene aerogel is prepared by a simple liquid infiltration-evaporation coating process and used directly as a composite cathode without metal substrate for lithium-sulfur batteries. Electrochemical tests demonstrate that the composite delivers a high discharge capacity of 934.4 mAh g-1 in the initial cycle and retains 485.5 mAh g-1 after 100 cycles at 0.1 C rate. In addition, the composite exhibits much lower potential barrier (∼2.40 V) and overpotential compared with previous reports, indicating that Li2S needs only a little energy to be activated. The excellent electrochemical performances could be attributed to the tiny particle size of Li2S and the superionic conducting Li3PS4 coating layer, which can shorten Li-ion and electron diffusion paths, improve the ionic conductivity, as well as retarding polysulfides dissolution into the electrolyte to some extent.

N+6Li system with flexible cluster wave function

NASA Astrophysics Data System (ADS)

Stubeda, D. J.; Fujiwara, Y.; Tang, Y. C.

1982-12-01

The n+6Li and p+6Li systems are studied with the single-channel resonating-group method. The 6Li internal wave function used is either a single translationally-invariant harmonic-oscillator shell-model function or a superposition of two such functions. The result shows that the main features of this system do not depend sensitively on which of these functions is employed, although significant differences in cross-section values do appear at backward angles. The fit to experimental data is only fair, indicating that the present calculation should be refined by including the N+6Li*(3+) inelastic channel, by taking into better account d+α clustering in 6Li, by carefully considering the effect of specific distortion, and by, perhaps, also adopting a noncentral nucleon-nucleon potential in the formulation. NUCLEAR REACTIONS 6Li(p, p), 6Li(n, n) calculated phase shifts and σ(θ). Resonating-group method with complex-generator-coordinate technique.

In operando quantitation of Li concentration for a commercial Li-ion rechargeable battery using high-energy X-ray Compton scattering.

PubMed

Suzuki, Kosuke; Suzuki, Ayahito; Ishikawa, Taiki; Itou, Masayoshi; Yamashige, Hisao; Orikasa, Yuki; Uchimoto, Yoshiharu; Sakurai, Yoshiharu; Sakurai, Hiroshi

2017-09-01

Compton scattering is one of the most promising probes for quantitating Li under in operando conditions, since high-energy X-rays, which have high penetration power, are used as the incident beam and the Compton-scattered energy spectrum has specific line-shapes for each element. An in operando quantitation method to determine the Li composition in electrodes has been developed by using line-shape (S-parameter) analysis of the Compton-scattered energy spectrum. In this study, S-parameter analysis has been applied to a commercial coin cell Li-ion rechargeable battery and the variation of the S-parameters during the charge/discharge cycle at the positive and negative electrodes has been obtained. By using calibration curves for Li composition in the electrodes, the change in Li composition of the positive and negative electrodes has been determined using the S-parameters simultaneously.

DISCOVERY OF SUPER-Li-RICH RED GIANTS IN DWARF SPHEROIDAL GALAXIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirby, Evan N.; Fu, Xiaoting; Deng, Licai

2012-06-10

Stars destroy lithium (Li) in their normal evolution. The convective envelopes of evolved red giants reach temperatures of millions of kelvin, hot enough for the {sup 7}Li(p, {alpha}){sup 4}He reaction to burn Li efficiently. Only about 1% of first-ascent red giants more luminous than the luminosity function bump in the red giant branch exhibit A(Li) > 1.5. Nonetheless, Li-rich red giants do exist. We present 15 Li-rich red giants-14 of which are new discoveries-among a sample of 2054 red giants in Milky Way dwarf satellite galaxies. Our sample more than doubles the number of low-mass, metal-poor ([Fe/H] {approx}< -0.7) Li-richmore » red giants, and it includes the most-metal-poor Li-enhanced star known ([Fe/H] = -2.82, A(Li){sub NLTE} = 3.15). Because most of the stars have Li abundances larger than the universe's primordial value, the Li in these stars must have been created rather than saved from destruction. These Li-rich stars appear like other stars in the same galaxies in every measurable regard other than Li abundance. We consider the possibility that Li enrichment is a universal phase of evolution that affects all stars, and it seems rare only because it is brief.« less

Controllable synthesis, morphology evolution and electrochemical properties of LiFePO4 cathode materials for Li-ion batteries.

PubMed

Song, Jianjun; Wang, Lin; Shao, Guangjie; Shi, Meiwu; Ma, Zhipeng; Wang, Guiling; Song, Wei; Liu, Shuang; Wang, Caixia

2014-05-07

Monodispersed LiFePO4 nanocrystals with diverse morphologies were successfully synthesized via a mild and controllable solvothermal approach with a mixture of ethylene glycol and oleic acid as the solvent. Morphology evolution of LiFePO4 nanoparticles from nanoplates to nanorods can be simply realized by varying the volume ratio of oleic acid to ethylene glycol. Moreover, the mechanism of competitive adsorption between ethylene glycol and oleic acid was proposed for the formation of different morphologies. Electrochemical measurements show that the LiFePO4/C nanorods have an initial discharge capacity of 155 mA h g(-1) at 0.5 C with a capacity retention of 80% at a high rate of 5 C, which confirms that LiFePO4/C nanorods exhibit excellent rate capability and cycling stability.

Li15Al3Si6 (Li14.6Al3.4Si6), a compound displaying a heterographite-like anionic framework.

PubMed

Spina, Laurent; Tillard, Monique; Belin, Claude

2003-02-01

The title compound, lithium aluminium silicide (15/3/6), crystallizes in the hexagonal centrosymmetric space group P6(3)/m. The three-dimensional structure of this ternary compound may be depicted as two interpenetrating lattices, namely a graphite-like Li(3)Al(3)Si(6) layer and a distorted diamond-like lithium lattice. As is commonly found for LiAl alloys, the Li and Al atoms are found to share some crystallographic sites. The diamond-like lattice is built up of Li cations, and the graphite-like anionic layer is composed of Si, Al and Li atoms in which Si and Al are covalently bonded [Si-Al = 2.4672 (4) A].

Synthesis and electrochemical characterization of mesoporous Li2FeSiO4/C composite cathode material for Li-ion batteries

NASA Astrophysics Data System (ADS)

Kumar, Ajay; Jayakumar, O. D.; Bazzi, Khadije; Nazri, Gholam-Abbas; Naik, Vaman M.; Naik, Ratna

2015-03-01

Lithium iron silicate (Li2FeSiO4) has the potential as cathode for Li ion batteries due to its high theoretical capacity (~ 330 mAh/g) and improved safety. The application of Li2FeSiO4 as cathode material has been challenged by its poor electronic conductivity and slow lithium ion diffusion in the solid phase. In order to solve these problems, we have synthesized mesoporous Li2FeSiO4/C composites by sol-gel method using the tri-block copolymer (P123) as carbon source. The phase purity and morphology of the composite materials were characterized by x-ray diffraction, SEM and TEM. The XRD pattern confirmed the formation of ~ 12 nm size Li2FeSiO4 crystallites in composites annealed at 600 °C for 6 h under argon atmosphere. The electrochemical properties are measured using the composite material as positive electrode in a standard coin cell configuration with lithium as the active anode and the cells were tested using AC impedance spectroscopy, cyclic voltammetry, and galvanostatic charge/discharge cycling. The Li2FeSiO4/C composites showed a discharge capacity of ~ 240 mAh/g at a rate of C/30 at room temperature. The effect of different annealing temperature and synthesis time on the electrochemical performance of Li2FeSiO4/C will be presented.

Stationary Flowing Liquid Lithium (SFLiLi) systems for tokamaks

NASA Astrophysics Data System (ADS)

Zakharov, Leonid; Gentile, Charles; Roquemore, Lane

2013-10-01

The present approach to magnetic fusion which relies on high recycling plasma-wall interaction has exhausted itself at the level of TFTR, JET, JT-60 devices with no realistic path to the burning plasma. Instead, magnetic fusion needs a return to its original idea of insulation of the plasma from the wall, which was the dominant approach in the 1970s and upon implementations has a clear path to the DEMO device with PDT ~= 100 MW and Qelectric > 1 . The SFLiLi systems of this talk is the technology tool for implementation of the guiding idea of magnetic fusion. It utilizes the unique properties of flowing LiLi to pump plasma particles and, thus, insulate plasma from the walls. The necessary flow rate, ~= 1 g3/s, is very small, thus, making the use of lithium practical and consistent with safety requirements. The talk describes how chemical activity of LiLi, which is the major technology challenge of using LiLi in tokamaks, is addressed by SFLiLi systems at the level of already performed (HT-7) experiment, and in ongoing implementations for a prototype of SFLiLi for tokamak divertors and the mid-plane limiter for EAST tokamak (to be tested in the next experimental campaign). This work is supported by US DoE contract No. DE-AC02-09-CH11466.

Structure of an LiKSO 4 single crystal studied by 7Li and 39K NMR at low temperature

NASA Astrophysics Data System (ADS)