Specific yield: compilation of specific yields for various materials

USGS Publications Warehouse

Johnson, A.I.

1967-01-01

Specific yield is defined as the ratio of (1) the volume of water that a saturated rock or soil will yield by gravity to (2) the total volume of the rock or soft. Specific yield is usually expressed as a percentage. The value is not definitive, because the quantity of water that will drain by gravity depends on variables such as duration of drainage, temperature, mineral composition of the water, and various physical characteristics of the rock or soil under consideration. Values of specific yields nevertheless offer a convenient means by which hydrologists can estimate the water-yielding capacities of earth materials and, as such, are very useful in hydrologic studies. The present report consists mostly of direct or modified quotations from many selected reports that present and evaluate methods for determining specific yield, limitations of those methods, and results of the determinations made on a wide variety of rock and soil materials. Although no particular values are recommended in this report, a table summarizes values of specific yield, and their averages, determined for 10 rock textures. The following is an abstract of the table. [Table

Development of Large-Eddy Interaction Model for inhomogeneous turbulent flows

NASA Technical Reports Server (NTRS)

Hong, S. K.; Payne, F. R.

1987-01-01

The objective of this paper is to demonstrate the applicability of a currently proposed model, with minimum empiricism, for calculation of the Reynolds stresses and other turbulence structural quantities in a channel. The current Large-Eddy Interaction Model not only yields Reynolds stresses but also presents an opportunity to illuminate typical characteristic motions of large-scale turbulence and the phenomenological aspects of engineering models for two Reynolds numbers.

Quantity, Revisited: An Object-Oriented Reusable Class

NASA Technical Reports Server (NTRS)

Funston, Monica Gayle; Gerstle, Walter; Panthaki, Malcolm

1998-01-01

"Quantity", a prototype implementation of an object-oriented class, was developed for two reasons: to help engineers and scientists manipulate the many types of quantities encountered during routine analysis, and to create a reusable software component to for large domain-specific applications. From being used as a stand-alone application to being incorporated into an existing computational mechanics toolkit, "Quantity" appears to be a useful and powerful object. "Quantity" has been designed to maintain the full engineering meaning of values with respect to units and coordinate systems. A value is a scalar, vector, tensor, or matrix, each of which is composed of Value Components, each of which may be an integer, floating point number, fuzzy number, etc., and its associated physical unit. Operations such as coordinate transformation and arithmetic operations are handled by member functions of "Quantity". The prototype has successfully tested such characteristics as maintaining a numeric value, an associated unit, and an annotation. In this paper we further explore the design of "Quantity", with particular attention to coordinate systems.

Mutually beneficial pollinator diversity and crop yield outcomes in small and large farms.

PubMed

Garibaldi, Lucas A; Carvalheiro, Luísa G; Vaissière, Bernard E; Gemmill-Herren, Barbara; Hipólito, Juliana; Freitas, Breno M; Ngo, Hien T; Azzu, Nadine; Sáez, Agustín; Åström, Jens; An, Jiandong; Blochtein, Betina; Buchori, Damayanti; Chamorro García, Fermín J; Oliveira da Silva, Fabiana; Devkota, Kedar; Ribeiro, Márcia de Fátima; Freitas, Leandro; Gaglianone, Maria C; Goss, Maria; Irshad, Mohammad; Kasina, Muo; Pacheco Filho, Alípio J S; Kiill, Lucia H Piedade; Kwapong, Peter; Parra, Guiomar Nates; Pires, Carmen; Pires, Viviane; Rawal, Ranbeer S; Rizali, Akhmad; Saraiva, Antonio M; Veldtman, Ruan; Viana, Blandina F; Witter, Sidia; Zhang, Hong

2016-01-22

Ecological intensification, or the improvement of crop yield through enhancement of biodiversity, may be a sustainable pathway toward greater food supplies. Such sustainable increases may be especially important for the 2 billion people reliant on small farms, many of which are undernourished, yet we know little about the efficacy of this approach. Using a coordinated protocol across regions and crops, we quantify to what degree enhancing pollinator density and richness can improve yields on 344 fields from 33 pollinator-dependent crop systems in small and large farms from Africa, Asia, and Latin America. For fields less than 2 hectares, we found that yield gaps could be closed by a median of 24% through higher flower-visitor density. For larger fields, such benefits only occurred at high flower-visitor richness. Worldwide, our study demonstrates that ecological intensification can create synchronous biodiversity and yield outcomes. Copyright © 2016, American Association for the Advancement of Science.

Complementary ecosystem services provided by pest predators and pollinators increase quantity and quality of coffee yields

PubMed Central

Classen, Alice; Peters, Marcell K.; Ferger, Stefan W.; Helbig-Bonitz, Maria; Schmack, Julia M.; Maassen, Genevieve; Schleuning, Matthias; Kalko, Elisabeth K. V.; Böhning-Gaese, Katrin; Steffan-Dewenter, Ingolf

2014-01-01

Wild animals substantially support crop production by providing ecosystem services, such as pollination and natural pest control. However, the strengths of synergies between ecosystem services and their dependencies on land-use management are largely unknown. Here, we took an experimental approach to test the impact of land-use intensification on both individual and combined pollination and pest control services in coffee production systems at Mount Kilimanjaro. We established a full-factorial pollinator and vertebrate exclosure experiment along a land-use gradient from traditional homegardens (agroforestry systems), shaded coffee plantations to sun coffee plantations (total sample size = 180 coffee bushes). The exclusion of vertebrates led to a reduction in fruit set of ca 9%. Pollinators did not affect fruit set, but significantly increased fruit weight of coffee by an average of 7.4%. We found no significant decline of these ecosystem services along the land-use gradient. Pest control and pollination service were thus complementary, contributing to coffee production by affecting the quantity and quality of a major tropical cash crop across different coffee production systems at Mount Kilimanjaro. PMID:24500173

Complementary ecosystem services provided by pest predators and pollinators increase quantity and quality of coffee yields.

PubMed

Classen, Alice; Peters, Marcell K; Ferger, Stefan W; Helbig-Bonitz, Maria; Schmack, Julia M; Maassen, Genevieve; Schleuning, Matthias; Kalko, Elisabeth K V; Böhning-Gaese, Katrin; Steffan-Dewenter, Ingolf

2014-03-22

Wild animals substantially support crop production by providing ecosystem services, such as pollination and natural pest control. However, the strengths of synergies between ecosystem services and their dependencies on land-use management are largely unknown. Here, we took an experimental approach to test the impact of land-use intensification on both individual and combined pollination and pest control services in coffee production systems at Mount Kilimanjaro. We established a full-factorial pollinator and vertebrate exclosure experiment along a land-use gradient from traditional homegardens (agroforestry systems), shaded coffee plantations to sun coffee plantations (total sample size = 180 coffee bushes). The exclusion of vertebrates led to a reduction in fruit set of ca 9%. Pollinators did not affect fruit set, but significantly increased fruit weight of coffee by an average of 7.4%. We found no significant decline of these ecosystem services along the land-use gradient. Pest control and pollination service were thus complementary, contributing to coffee production by affecting the quantity and quality of a major tropical cash crop across different coffee production systems at Mount Kilimanjaro.

And, not or: Quality, quantity in scientific publishing

PubMed Central

Allesina, Stefano

2017-01-01

Scientists often perceive a trade-off between quantity and quality in scientific publishing: finite amounts of time and effort can be spent to produce few high-quality papers or subdivided to produce many papers of lower quality. Despite this perception, previous studies have indicated the opposite relationship, in which productivity (publishing more papers) is associated with increased paper quality (usually measured by citation accumulation). We examine this question in a novel way, comparing members of the National Academy of Sciences with themselves across years, and using a much larger dataset than previously analyzed. We find that a member’s most highly cited paper in a given year has more citations in more productive years than in in less productive years. Their lowest cited paper each year, on the other hand, has fewer citations in more productive years. To disentangle the effect of the underlying distributions of citations and productivities, we repeat the analysis for hypothetical publication records generated by scrambling each author’s citation counts among their publications. Surprisingly, these artificial histories re-create the above trends almost exactly. Put another way, the observed positive relationship between quantity and quality can be interpreted as a consequence of randomly drawing citation counts for each publication: more productive years yield higher-cited papers because they have more chances to draw a large value. This suggests that citation counts, and the rewards that have come to be associated with them, may be more stochastic than previously appreciated. PMID:28570567

Production of transgenic-cloned pigs expressing large quantities of recombinant human lysozyme in milk.

PubMed

Lu, Dan; Liu, Shen; Shang, Shengzhe; Wu, Fangfang; Wen, Xiao; Li, Zhiyuan; Li, Yan; Hu, Xiaoxiang; Zhao, Yaofeng; Li, Qiuyan; Li, Ning

2015-01-01

Human lysozyme is a natural non-specific immune factor in human milk that plays an important role in the defense of breastfed infants against pathogen infection. Although lysozyme is abundant in human milk, there is only trace quantities in pig milk. Here, we successfully generated transgenic cloned pigs with the expression vector pBAC-hLF-hLZ-Neo and their first generation hybrids (F1). The highest concentration of recombinant human lysozyme (rhLZ) with in vitro bioactivity was 2759.6 ± 265.0 mg/L in the milk of F0 sows. Compared with wild-type milk, rhLZ milk inhibited growth of Escherichia coli K88 during the exponential growth phase. Moreover, rhLZ in milk from transgenic sows was directly absorbed by the intestine of piglets with no observable anaphylactic reaction. Our strategy may provide a powerful tool for large-scale production of this important human protein in pigs to improve resistance to pathogen infection.

Enhancing Least-Squares Finite Element Methods Through a Quantity-of-Interest

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chaudhry, Jehanzeb Hameed; Cyr, Eric C.; Liu, Kuo

2014-12-18

Here, we introduce an approach that augments least-squares finite element formulations with user-specified quantities-of-interest. The method incorporates the quantity-of-interest into the least-squares functional and inherits the global approximation properties of the standard formulation as well as increased resolution of the quantity-of-interest. We establish theoretical properties such as optimality and enhanced convergence under a set of general assumptions. Central to the approach is that it offers an element-level estimate of the error in the quantity-of-interest. As a result, we introduce an adaptive approach that yields efficient, adaptively refined approximations. Several numerical experiments for a range of situations are presented to supportmore » the theory and highlight the effectiveness of our methodology. Notably, the results show that the new approach is effective at improving the accuracy per total computational cost.« less

Combining Costs and Benefits of Animal Activities to Assess Net Yield Outcomes in Apple Orchards

PubMed Central

Luck, Gary W.

2016-01-01

Diverse animal communities influence ecosystem function in agroecosystems through positive and negative plant-animal interactions. Yet, past research has largely failed to examine multiple interactions that can have opposing impacts on agricultural production in a given context. We collected data on arthropod communities and yield quality and quantity parameters (fruit set, yield loss and net outcomes) in three major apple-growing regions in south-eastern Australia. We quantified the net yield outcome (accounting for positive and negative interactions) of multiple animal activities (pollination, fruit damage, biological control) across the entire growing season on netted branches, which excluded vertebrate predators of arthropods, and open branches. Net outcome was calculated as the number of undamaged fruit at harvest as a proportion of the number of blossoms (i.e., potential fruit yield). Vertebrate exclusion resulted in lower levels of fruit set and higher levels of arthropod damage to apples, but did not affect net outcomes. Yield quality and quantity parameters (fruit set, yield loss, net outcomes) were not directly associated with arthropod functional groups. Model variance and significant differences between the ratio of pest to beneficial arthropods between regions indicated that complex relationships between environmental factors and multiple animal interactions have a combined effect on yield. Our results show that focusing on a single crop stage, species group or ecosystem function/service can overlook important complexity in ecological processes within the system. Accounting for this complexity and quantifying the net outcome of ecological interactions within the system, is more informative for research and management of biodiversity and ecosystem services in agricultural landscapes. PMID:27391022

Combining Costs and Benefits of Animal Activities to Assess Net Yield Outcomes in Apple Orchards.

PubMed

Saunders, Manu E; Luck, Gary W

2016-01-01

Diverse animal communities influence ecosystem function in agroecosystems through positive and negative plant-animal interactions. Yet, past research has largely failed to examine multiple interactions that can have opposing impacts on agricultural production in a given context. We collected data on arthropod communities and yield quality and quantity parameters (fruit set, yield loss and net outcomes) in three major apple-growing regions in south-eastern Australia. We quantified the net yield outcome (accounting for positive and negative interactions) of multiple animal activities (pollination, fruit damage, biological control) across the entire growing season on netted branches, which excluded vertebrate predators of arthropods, and open branches. Net outcome was calculated as the number of undamaged fruit at harvest as a proportion of the number of blossoms (i.e., potential fruit yield). Vertebrate exclusion resulted in lower levels of fruit set and higher levels of arthropod damage to apples, but did not affect net outcomes. Yield quality and quantity parameters (fruit set, yield loss, net outcomes) were not directly associated with arthropod functional groups. Model variance and significant differences between the ratio of pest to beneficial arthropods between regions indicated that complex relationships between environmental factors and multiple animal interactions have a combined effect on yield. Our results show that focusing on a single crop stage, species group or ecosystem function/service can overlook important complexity in ecological processes within the system. Accounting for this complexity and quantifying the net outcome of ecological interactions within the system, is more informative for research and management of biodiversity and ecosystem services in agricultural landscapes.

Effects of fracturing on well yields in the coalfield areas of Wise and Dickenson counties, southwestern Virginia

USGS Publications Warehouse

Wright, W.G.

1985-01-01

Fracturing associated with lineaments are the primary influence on yields from wells in the coalfields of southwestern Virgnia. Graphical comparison of yield from wells shows that wells located in valleys with lineaments produce larger quantities of water than wells in valleys without lineaments. Pumping tests at wells located in valleys with lineaments indicate transmissivities as high as 598 ft2/d, caused principally by secondary permeability. Analysis of data collected from packer-injection tests in a test hole located on a ridge indicate relatively large hydraulic conductivities ranging from 2x10(sup -2) to 1x10(sup -1) feet per day in upper parts of the test hole, compared to values typical of unfractured rocks in the study area. Fracturing due to stress relief contribute to these large values. Yields from wells located on lineaments are consistently higher than well yields from wells in unfractured rock in the study area, but well yields from wells placed randomly in areas suspected of having stress relief fractures cannot be predicted. (USGS)

Using large-scale diagnostic quantities to investigate change in East Coast Lows

NASA Astrophysics Data System (ADS)

Ji, Fei; Evans, Jason P.; Argueso, Daniel; Fita, Lluis; Di Luca, Alejandro

2015-11-01

East Coast Lows (ECLs) are intense low-pressure systems that affect the eastern seaboard of Australia. They have attracted research interest for both their destructive nature and water supplying capability. Estimating the changes in ECLs in the future has a major impact on emergency response as well as water management strategies for the coastal communities on the east coast of Australia. In this study, ECLs were identified using two large-scale diagnostic quantities: isentropic potential vorticity (IPV) and geostrophic vorticity (GV), which were calculated from outputs of historical and future regional climate simulations from the NSW/ACT regional climate modelling (NARCliM) project. The diagnostic results for the historical period were evaluated against a subjective ECL event database. Future simulations using a high emission scenario were examined to estimate changes in frequency, duration, and intensity of ECLs. The use of a relatively high resolution regional climate model makes this the first study to examine future changes in ECLs while resolving the full range of ECL sizes which can be as small as 100-200 km in diameter. The results indicate that it is likely that there will be fewer ECLs, with weaker intensity in the future. There could also be a seasonal shift in ECLs from cool months to warm months. These changes have the potential to significantly impact the water security on the east coast of Australia.

Computing wheat nitrogen requirements from grain yield and protein maps

USDA-ARS?s Scientific Manuscript database

Optical protein sensors and mass-flow yield monitors provide the opportunity to continuously measure grain quality and quantity during harvesting. This chapter illustrates how yield monitor and grain protein measurements may provide useful postharvest information for evaluating water or nitrogen (N)...

Computing wheat nitrogen requirements from grain yield and protein maps

USDA-ARS?s Scientific Manuscript database

Optical protein sensors and mass-flow yield monitors provide the opportunity to continuously measure grain quality and quantity during harvesting. This chapter illustrates how yield monitor and grain protein measurements may provide useful post-harvest information for evaluating water or nitrogen (...

Photosynthesis-related quantities for education and modeling.

PubMed

Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

2013-11-01

A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

Choosing Between Yeast and Bacterial Expression Systems: Yield Dependent

NASA Technical Reports Server (NTRS)

Miller, Rebecca S.; Malone, Christine C.; Moore, Blake P.; Burk, Melissa; Crawford, Lisa; Karr, Laurel J.; Curreri, Peter A. (Technical Monitor)

2002-01-01

Green fluorescent protein (GFP) is a naturally occurring fluorescent protein isolated from the jellyfish Aequorea victoria. The intrinsic fluorescence of the protein is due to a chromophore located in the center of the molecule. Its usefulness has been established as a marker for gene expression and localization of gene products. GFP has recently been utilized as a model protein for crystallization studies at NASA/MSFC, both in earth-based and in microgravity experiments. Because large quantities of purified protein were needed, the cDNA of GFP was cloned into the Pichia pastoris pPICZ(alpha) C strain, with very little protein secreted into the media. Microscopic analysis prior to harvest showed gigantic green fluorescent yeast, but upon harvesting most protein was degraded. Trial fermentations of GFP cloned into pPICZ A for intracellular expression provided unsatisfactory yield. GFP cloned into E, coli was overexpressed at greater than 150 mg/liter, with purification yields at greater than 100mg/liter.

The impact of large-scale circulation patterns on summer crop yields in IP

NASA Astrophysics Data System (ADS)

Capa Morocho, Mirian; Rodríguez Fonseca, Belén; Ruiz Ramos, Margarita

2014-05-01

Large-scale circulations patterns (ENSO, NAO) have been shown to have a significant impact on seasonal weather, and therefore on crop yield over many parts of the world(Garnett and Khandekar, 1992; Aasa et al., 2004; Rozas and Garcia-Gonzalez, 2012). In this study, we analyze the influence of large-scale circulation patterns and regional climate on the principal components of maize yield variability in Iberian Peninsula (IP) using reanalysis datasets. Additionally, we investigate the modulation of these relationships by multidecadal patterns. This study is performed analyzing long time series of maize yield, only climate dependent, computed with the crop model CERES-maize (Jones and Kiniry, 1986) included in Decision Support System for Agrotechnology Transfer (DSSAT v.4.5). To simulate yields, reanalysis daily data of radiation, maximum and minimum temperature and precipitation were used. The reanalysis climate data were obtained from National Center for Environmental Prediction (20th Century and NCEP) and European Centre for Medium-Range Weather Forecasts (ECMWF) data server (ERA 40 and ERA Interim). Simulations were run at five locations: Lugo (northwestern), Lerida (NE), Madrid (central), Albacete (southeastern) and Córdoba (S IP) (Gabaldón et al., 2013). From these time series standardized anomalies were calculated. Afterwards, time series were time filtered to focus on the interannual-to-multiannual variability, splitting up in two components: low frequency (LF) and high frequency (HF) time scales. The principal components of HF yield anomalies in IP were compared with a set of documented patterns. These relationships were compared with multidecadal patterns, as Atlanctic Multidecadal Oscillations (AMO) and Interdecadal Pacific Oscillations (IPO). The results of this study have important implications in crop forecasting. In this way, it may have a positive impact on both public (agricultural planning) and private (decision support to farmers, insurance

Use of bioreactors for culturing human retinal organoids improves photoreceptor yields.

PubMed

Ovando-Roche, Patrick; West, Emma L; Branch, Matthew J; Sampson, Robert D; Fernando, Milan; Munro, Peter; Georgiadis, Anastasios; Rizzi, Matteo; Kloc, Magdalena; Naeem, Arifa; Ribeiro, Joana; Smith, Alexander J; Gonzalez-Cordero, Anai; Ali, Robin R

2018-06-13

The use of human pluripotent stem cell-derived retinal cells for cell therapy strategies and disease modelling relies on the ability to obtain healthy and organised retinal tissue in sufficient quantities. Generating such tissue is a lengthy process, often taking over 6 months of cell culture, and current approaches do not always generate large quantities of the major retinal cell types required. We adapted our previously described differentiation protocol to investigate the use of stirred-tank bioreactors. We used immunohistochemistry, flow cytometry and electron microscopy to characterise retinal organoids grown in standard and bioreactor culture conditions. Our analysis revealed that the use of bioreactors results in improved laminar stratification as well as an increase in the yield of photoreceptor cells bearing cilia and nascent outer-segment-like structures. Bioreactors represent a promising platform for scaling up the manufacture of retinal cells for use in disease modelling, drug screening and cell transplantation studies.

Spatial and Temporal Uncertainty of Crop Yield Aggregations

NASA Technical Reports Server (NTRS)

Porwollik, Vera; Mueller, Christoph; Elliott, Joshua; Chryssanthacopoulos, James; Iizumi, Toshichika; Ray, Deepak K.; Ruane, Alex C.; Arneth, Almut; Balkovic, Juraj; Ciais, Philippe;

Soil erosion and sediment yield, a double barrel problem in South Africa's only large river network without a dam

NASA Astrophysics Data System (ADS)

Le Roux, Jay

2016-04-01

Soil erosion not only involves the loss of fertile topsoil but is also coupled with sedimentation of dams, a double barrel problem in semi-arid regions where water scarcity is frequent. Due to increasing water requirements in South Africa, the Department of Water and Sanitation is planning water resource development in the Mzimvubu River Catchment, which is the only large river network in the country without a dam. Two dams are planned including a large irrigation dam and a hydropower dam. However, previous soil erosion studies indicate that large parts of the catchment is severely eroded. Previous studies, nonetheless, used mapping and modelling techniques that represent only a selection of erosion processes and provide insufficient information about the sediment yield. This study maps and models the sediment yield comprehensively by means of two approaches over a five-year timeframe between 2007 and 2012. Sediment yield contribution from sheet-rill erosion was modelled with ArcSWAT (a graphical user interface for SWAT in a GIS), whereas gully erosion contributions were estimated using time-series mapping with SPOT 5 imagery followed by gully-derived sediment yield modelling in a GIS. Integration of the sheet-rill and gully results produced a total sediment yield map, with an average of 5 300 t km-2 y-1. Importantly, the annual average sediment yield of the areas where the irrigation dam and hydropower dam will be built is around 20 000 t km-2 y-1. Without catchment rehabilitation, the life expectancy of the irrigation dam and hydropower dam could be 50 and 40 years respectively.

Wafer scale fabrication of carbon nanotube thin film transistors with high yield

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Boyuan; Liang, Xuelei, E-mail: liangxl@pku.edu.cn, E-mail: ssxie@iphy.ac.cn; Yan, Qiuping

Carbon nanotube thin film transistors (CNT-TFTs) are promising candidates for future high performance and low cost macro-electronics. However, most of the reported CNT-TFTs are fabricated in small quantities on a relatively small size substrate. The yield of large scale fabrication and the performance uniformity of devices on large size substrates should be improved before the CNT-TFTs reach real products. In this paper, 25 200 devices, with various geometries (channel width and channel length), were fabricated on 4-in. size ridged and flexible substrates. Almost 100% device yield were obtained on a rigid substrate with high out-put current (>8 μA/μm), high on/off current ratiomore » (>10{sup 5}), and high mobility (>30 cm{sup 2}/V·s). More importantly, uniform performance in 4-in. area was achieved, and the fabrication process can be scaled up. The results give us more confidence for the real application of the CNT-TFT technology in the near future.« less

Brazilian Soybean Yields and Yield Gaps Vary with Farm Size

NASA Astrophysics Data System (ADS)

Jeffries, G. R.; Cohn, A.; Griffin, T. S.; Bragança, A.

2017-12-01

Understanding the farm size-specific characteristics of crop yields and yield gaps may help to improve yields by enabling better targeting of technical assistance and agricultural development programs. Linking remote sensing-based yield estimates with property boundaries provides a novel view of the relationship between farm size and yield structure (yield magnitude, gaps, and stability over time). A growing literature documents variations in yield gaps, but largely ignores the role of farm size as a factor shaping yield structure. Research on the inverse farm size-productivity relationship (IR) theory - that small farms are more productive than large ones all else equal - has documented that yield magnitude may vary by farm size, but has not considered other yield structure characteristics. We examined farm size - yield structure relationships for soybeans in Brazil for years 2001-2015. Using out-of-sample soybean yield predictions from a statistical model, we documented 1) gaps between the 95th percentile of attained yields and mean yields within counties and individual fields, and 2) yield stability defined as the standard deviation of time-detrended yields at given locations. We found a direct relationship between soy yields and farm size at the national level, while the strength and the sign of the relationship varied by region. Soybean yield gaps were found to be inversely related to farm size metrics, even when yields were only compared to farms of similar size. The relationship between farm size and yield stability was nonlinear, with mid-sized farms having the most stable yields. The work suggests that farm size is an important factor in understanding yield structure and that opportunities for improving soy yields in Brazil are greatest among smaller farms.

Quantity Representation in Children and Rhesus Monkeys: Linear Versus Logarithmic Scales

ERIC Educational Resources Information Center

Beran, Michael J.; Johnson-Pynn, Julie S.; Ready, Christopher

2008-01-01

The performances of 4- and 5-year-olds and rhesus monkeys were compared using a computerized task for quantity assessment. Participants first learned two quantity anchor values and then responded to intermediate values by classifying them as similar to either the large anchor or the small anchor. Of primary interest was an assessment of where the…

Quantity and Quality of Computer Use and Academic Achievement: Evidence from a Large-Scale International Test Program

ERIC Educational Resources Information Center

Cheema, Jehanzeb R.; Zhang, Bo

2013-01-01

This study looked at the effect of both quantity and quality of computer use on achievement. The Program for International Student Assessment (PISA) 2003 student survey comprising of 4,356 students (boys, n = 2,129; girls, n = 2,227) was used to predict academic achievement from quantity and quality of computer use while controlling for…

Sustainable yields from large diameter wells in shallow weathered aquifers

NASA Astrophysics Data System (ADS)

Rushton, K. R.; de Silva, C. S.

2016-08-01

Large diameter wells in shallow weathered aquifers provide a valuable source of water for domestic and agricultural purposes in many locations including the Indian subcontinent. However, when used for irrigation, these wells often fail towards the end of the dry season. By considering two case studies in the dry and intermediate rainfall zones of Sri Lanka, reasons for the limited yield of these wells are identified. The first case study is concerned with a sloping catchment; a significant proportion of the precipitation during the rainy season either becomes runoff or passes down-gradient through the aquifer and is discharged at the ground surface. Furthermore, during the dry season, groundwater discharge continues. In the second case study the topography is generally flat but, even though the aquifer fills most years during the rainy season, there is often only sufficient water to irrigate about half of each farmer's holding. These investigations are based on field information and the development of conceptual and computational models. Of critical importance in assessing the long term yield of a well is the formation of a seepage face on the side of the well, with the water table a significant distance above the pumping water level. Consequently the water table may only be lowered to about half the depth of the well. The paper concludes with recommendations for the exploitation of groundwater from shallow weathered aquifers to minimise the risk of failure during the dry season.

Application of cooperative and non-cooperative games in large-scale water quantity and quality management: a case study.

PubMed

Mahjouri, Najmeh; Ardestani, Mojtaba

2011-01-01

In this paper, two cooperative and non-cooperative methodologies are developed for a large-scale water allocation problem in Southern Iran. The water shares of the water users and their net benefits are determined using optimization models having economic objectives with respect to the physical and environmental constraints of the system. The results of the two methodologies are compared based on the total obtained economic benefit, and the role of cooperation in utilizing a shared water resource is demonstrated. In both cases, the water quality in rivers satisfies the standards. Comparing the results of the two mentioned approaches shows the importance of acting cooperatively to achieve maximum revenue in utilizing a surface water resource while the river water quantity and quality issues are addressed.

How tobacco companies have used package quantity for consumer targeting.

PubMed

Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

2018-05-31

Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Immunocapture and microplate-based activity and quantity measurement of pyruvate dehydrogenase in human peripheral blood mononuclear cells.

PubMed

Liu, Xiaowen; Pervez, Hira; Andersen, Lars W; Uber, Amy; Montissol, Sophia; Patel, Parth; Donnino, Michael W

2015-01-01

Pyruvate dehydrogenase (PDH) activity is altered in many human disorders. Current methods require tissue samples and yield inconsistent results. We describe a modified method for measuring PDH activity from isolated human peripheral blood mononuclear cells (PBMCs). RESULTS/METHODOLOGY: We found that PDH activity and quantity can be successfully measured in human PBMCs. Freeze-thaw cycles cannot efficiently disrupt the mitochondrial membrane. Processing time of up to 20 h does not affect PDH activity with proteinase inhibitor addition and a detergent concentration of 3.3% showed maximum yield. Sample protein concentration is correlated to PDH activity and quantity in human PBMCs from healthy subjects. Measuring PDH activity from PBMCs is a novel, easy and less invasive way to further understand the role of PDH in human disease.

Synergistic interactions of ecosystem services: florivorous pest control boosts crop yield increase through insect pollination

PubMed Central

Albrecht, Matthias

2016-01-01

Insect pollination and pest control are pivotal functions sustaining global food production. However, they have mostly been studied in isolation and how they interactively shape crop yield remains largely unexplored. Using controlled field experiments, we found strong synergistic effects of insect pollination and simulated pest control on yield quantity and quality. Their joint effect increased yield by 23%, with synergistic effects contributing 10%, while their single contributions were 7% and 6%, respectively. The potential economic benefit for a farmer from the synergistic effects (12%) was 1.8 times greater than their individual contributions (7% each). We show that the principal underlying mechanism was a pronounced pest-induced reduction in flower lifetime, resulting in a strong reduction in the number of pollinator visits a flower receives during its lifetime. Our findings highlight the importance of non-additive interactions among ecosystem services (ES) when valuating, mapping or predicting them and reveal fundamental implications for ecosystem management and policy aimed at maximizing ES for sustainable agriculture. PMID:26865304

Scaleable processes for the manufacture of therapeutic quantities of plasmid DNA.

PubMed

Shamlou, Parviz Ayazi

2003-06-01

The need for scaleable processes to manufacture therapeutic plasmid DNA (pDNA) is easy to overlook when attention is focused primarily on vector design and establishment of early clinical results. pDNA is a large molecule and has properties that are similar to those of the contaminating chromosomal DNA. These, combined with the low initial concentration of plasmids in the host cell, provide unique process challenges that require significant upfront design to establish robust manufacturing processes that can also comply with current Good Manufacturing Practice ('cGMP') and produce milligram-to-kilogram quantities of pDNA product. This review describes promising scaleable processes that are currently being assessed for production of therapeutic supercoiled pDNA. Fermentation strategies for improving supercoiled plasmid yield and reducing contaminant concentrations are reviewed, and downstream processes are assessed for their ability to efficiently remove cellular contaminants, separate the supercoiled form of the pDNA from its open circular and linear forms, and prepare the purified drug substance for formulation. Current strategies are presented for developing stable delivery systems, and approaches to quality assurance and quality control are discussed.

Application of sensitivity-analysis techniques to the calculation of topological quantities

NASA Astrophysics Data System (ADS)

Gilchrist, Stuart

2017-08-01

Magnetic reconnection in the corona occurs preferentially at sites where the magnetic connectivity is either discontinuous or has a large spatial gradient. Hence there is a general interest in computing quantities (like the squashing factor) that characterize the gradient in the field-line mapping function. Here we present an algorithm for calculating certain (quasi)topological quantities using mathematical techniques from the field of ``sensitivity-analysis''. The method is based on the calculation of a three dimensional field-line mapping Jacobian from which all the present topological quantities of interest can be derived. We will present the algorithm and the details of a publicly available set of libraries that implement the algorithm.

Defining value through quantity and quality-Chimpanzees (Pan troglodytes) undervalue food quantities when items are broken.

PubMed

Parrish, Audrey E; Evans, Theodore A; Beran, Michael J

2015-02-01

Decision-making largely is influenced by the relative value of choice options, and the value of such options can be determined by a combination of different factors (e.g., the quantity, size, or quality of a stimulus). In this study, we examined the competing influences of quantity (i.e., the number of food items in a set) and quality (i.e., the original state of a food item) of choice items on chimpanzees' food preferences in a two-option natural choice paradigm. In Experiment 1, chimpanzees chose between sets of food items that were either entirely whole or included items that were broken into pieces before being shown to the chimpanzees. Chimpanzees exhibited a bias for whole food items even when such choice options consisted of a smaller overall quantity of food than the sets containing broken items. In Experiment 2, chimpanzees chose between sets of entirely whole food items and sets of initially whole items that were subsequently broken in view of the chimpanzees just before choice time. Chimpanzees continued to exhibit a bias for sets of whole items. In Experiment 3, chimpanzees chose between sets of new food items that were initially discrete but were subsequently transformed into a larger cohesive unit. Here, chimpanzees were biased to choose the discrete sets that retained their original qualitative state rather than toward the cohesive or clumped sets. These results demonstrate that beyond a food set's quantity (i.e., the value dimension that accounts for maximization in terms of caloric intake), other seemingly non-relevant features (i.e., quality in terms of a set's original state) affect how chimpanzees assign value to their choice options. Copyright © 2014 Elsevier B.V. All rights reserved.

Immunocapture and microplate-based activity and quantity measurement of pyruvate dehydrogenase in human peripheral blood mononuclear cells

PubMed Central

Liu, Xiaowen; Pervez, Hira; Andersen, Lars W; Uber, Amy; Montissol, Sophia; Patel, Parth; Donnino, Michael W

2015-01-01

Background Pyruvate dehydrogenase (PDH) activity is altered in many human disorders. Current methods require tissue samples and yield inconsistent results. We describe a modified method for measuring PDH activity from isolated human peripheral blood mononuclear cells (PBMCs). Results/Methodology We found that PDH activity and quantity can be successfully measured in human PBMCs. Freeze-thaw cycles cannot efficiently disrupt the mitochondrial membrane. Processing time of up to 20 h does not affect PDH activity with proteinase inhibitor addition and a detergent concentration of 3.3% showed maximum yield. Sample protein concentration is correlated to PDH activity and quantity in human PBMCs from healthy subjects. Conclusion Measuring PDH activity from PBMCs is a novel, easy and less invasive way to further understand the role of PDH in human disease. PMID:25826140

Accelerated warming and emergent trends in fisheries biomass yields of the world's large marine ecosystems.

PubMed

Sherman, Kenneth; Belkin, Igor M; Friedland, Kevin D; O'Reilly, John; Hyde, Kimberly

2009-06-01

Information on the effects of global climate change on trends in global fisheries biomass yields has been limited in spatial and temporal scale. Results are presented of a global study of the impact of sea surface temperature (SST) changes over the last 25 years on the fisheries yields of 63 large marine ecosystems (LMEs) that annually produce 80% of the world's marine fisheries catches. Warming trends were observed in 61 LMEs around the globe. In 18 of the LMEs, rates of SST warming were two to four times faster during the past 25 years than the globally averaged rates of SST warming reported by the Intergovernmental Panel on Climate Change in 2007. Effects of warming on fisheries biomass yields were greatest in the fast-warming northern Northeast Atlantic LMEs, where increasing trends in fisheries biomass yields were related to zooplankton biomass increases. In contrast, fisheries biomass yields of LMEs in the fast-warming, more southerly reaches of the Northeast Atlantic were declining in response to decreases in zooplankton abundance. The LMEs around the margins of the Indian Ocean, where SSTs were among the world's slowest warming, revealed a consistent pattern of fisheries biomass increases during the past 25 years, driven principally by human need for food security from fisheries resources. As a precautionary approach toward more sustainable fisheries utilization, management measures to limit the total allowable catch through a cap-and-sustain approach are suggested for the developing nations recently fishing heavily on resources of the Agulhas Current, Somali Current, Arabian Sea, and Bay of Bengal LMEs.

Chemical Waste Management for the Conditionally Exempt Small Quantity Generator

NASA Astrophysics Data System (ADS)

Zimmer, Steven W.

1999-06-01

Management of hazardous chemical wastes generated as a part of the curriculum poses a significant task for the individual responsible for maintaining compliance with all rules and regulations from the Environmental Protection Agency and the Department of Transportation while maintaining the principles of OSHA's Lab Standard and the Hazard Communication Standard. For schools that generate relatively small quantities of waste, an individual can effectively manage the waste program without becoming overly burdened by the EPA regulations required for those generating large quantities of waste, if given the necessary support from the institution.

Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

PubMed

Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L

2018-01-01

This study examines whether energy drink use and binge drinking predict sleep quantity, sleep quality, and next-day tiredness among college students. Web-based daily data on substance use and sleep were collected across four semesters in 2009 and 2010 from 667 individuals for up to 56 days each, yielding information on 25,616 person-days. Controlling for average levels of energy drink use and binge drinking (i.e., 4+ drinks for women, 5+ drinks for men), on days when students consumed energy drinks, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not use energy drinks. Similarly, on days when students binge drank, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not binge drink. There was no significant interaction effect between binge drinking and energy drink use on the outcomes.

Drought effects on composition and yield for corn stover, mixed grasses, and Miscanthus as bioenergy feedstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Emerson, Rachel; Hoover, Amber; Ray, Allison

Drought conditions in 2012 were some of the most severe in recent history. The purpose of this study is to examine the impact of drought on quality, quantity, and theoretical ethanol yield (TEY) of three bioenergy feedstocks, corn stover, mixed grasses from Conservation Reserve Program lands, and Miscanthus × giganteus. To assess drought effects on these feedstocks, samples from 2010 (minimal to no drought) and 2012 (severe drought) were compared from multiple locations in the US. In all feedstocks, drought significantly increased extractives and reduced structural sugars and lignin; subsequently, TEYs were reduced 10–15%. Biomass yields were significantly reduced formore » M. × giganteus and mixed grasses. When reduction in quality and quantity were combined, TEYs decreased 26–59%. Drought negatively affected biomass quality and quantity that resulted in significant TEY reductions. As a result, such fluctuations in biomass quality and yield may have significant consequences for developing lignocellulosic biorefineries.« less

Drought effects on composition and yield for corn stover, mixed grasses, and Miscanthus as bioenergy feedstocks

DOE PAGES

Emerson, Rachel; Hoover, Amber; Ray, Allison; ...

2014-07-04

Drought conditions in 2012 were some of the most severe in recent history. The purpose of this study is to examine the impact of drought on quality, quantity, and theoretical ethanol yield (TEY) of three bioenergy feedstocks, corn stover, mixed grasses from Conservation Reserve Program lands, and Miscanthus × giganteus. To assess drought effects on these feedstocks, samples from 2010 (minimal to no drought) and 2012 (severe drought) were compared from multiple locations in the US. In all feedstocks, drought significantly increased extractives and reduced structural sugars and lignin; subsequently, TEYs were reduced 10–15%. Biomass yields were significantly reduced formore » M. × giganteus and mixed grasses. When reduction in quality and quantity were combined, TEYs decreased 26–59%. Drought negatively affected biomass quality and quantity that resulted in significant TEY reductions. As a result, such fluctuations in biomass quality and yield may have significant consequences for developing lignocellulosic biorefineries.« less

Water yield following forest-grass-forest transitions

Treesearch

Katherine J. Elliott; Peter V. Caldwell; Steven T. Brantley; Chelcy F. Miniat; James M. Vose; Wayne Swank

2017-01-01

Many currently forested areas in the southern Appalachians were harvested in the early 1900s and cleared for agriculture or pasture, but have since been abandoned and reverted to forest (old-field succession). Land-use and land-cover changes such as these may have altered the timing and quantity of water yield (Q). We examined 80 years of streamflow and vegetation data...

Analysis of a large dataset of mycorrhiza inoculation field trials on potato shows highly significant increases in yield.

PubMed

Hijri, Mohamed

2016-04-01

An increasing human population requires more food production in nutrient-efficient systems in order to simultaneously meet global food needs while reducing the environmental footprint of agriculture. Arbuscular mycorrhizal fungi (AMF) have the potential to enhance crop yield, but their efficiency has yet to be demonstrated in large-scale crop production systems. This study reports an analysis of a dataset consisting of 231 field trials in which the same AMF inoculant (Rhizophagus irregularis DAOM 197198) was applied to potato over a 4-year period in North America and Europe under authentic field conditions. The inoculation was performed using a liquid suspension of AMF spores that was sprayed onto potato seed pieces, yielding a calculated 71 spores per seed piece. Statistical analysis showed a highly significant increase in marketable potato yield (ANOVA, P < 0.0001) for inoculated fields (42.2 tons/ha) compared with non-inoculated controls (38.3 tons/ha), irrespective of trial year. The average yield increase was 3.9 tons/ha, representing 9.5 % of total crop yield. Inoculation was profitable with a 0.67-tons/ha increase in yield, a threshold reached in almost 79 % of all trials. This finding clearly demonstrates the benefits of mycorrhizal-based inoculation on crop yield, using potato as a case study. Further improvements of these beneficial inoculants will help compensate for crop production deficits, both now and in the future.

Measurements of {Gamma}(Z{sup O} {yields} b{bar b})/{Gamma}(Z{sup O} {yields} hadrons) using the SLD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neal, H.A. Jr. II

1995-07-01

The quantity R{sub b} = {Gamma}(Z{sup o} {yields}b{bar b})/{Gamma}(Z{sup o} {yields} hadrons) is a sensitive measure of corrections to the Zbb vertex. The precision necessary to observe the top quark mass dependent corrections is close to being achieved. LEP is already observing a 1.8{sigma} deviation from the Standard Model prediction. Knowledge of the top quark mass combined with the observation of deviations from the Standard Model prediction would indicate new physics. Models which include charged Higgs or light SUSY particles yield predictions for R{sub b} appreciably different from the Standard Model. In this thesis two independent methods are used tomore » measure R{sub b}. One uses a general event tag which determines R{sub b} from the rate at which events are tagged as Z{sup o} {yields} b{bar b} in data and the estimated rates at which various flavors of events are tagged from the Monte Carlo. The second method reduces the reliance on the Monte Carlo by separately tagging each hemisphere as containing a b-decay. The rates of single hemisphere tagged events and both hemisphere tagged events are used to determine the tagging efficiency for b-quarks directly from the data thus eliminating the main sources of systematic error present in the event tag. Both measurements take advantage of the unique environment provided by the SLAC Linear Collider (SLC) and the SLAC Large Detector (SLD). From the event tag a result of R{sub b} = 0.230{plus_minus}0.004{sub statistical}{plus_minus}0.013{sub systematic} is obtained. The higher precision hemisphere tag result obtained is R{sub b} = 0.218{plus_minus}0.004{sub statistical}{plus_minus}0.004{sub systematic}{plus_minus}0.003{sub Rc}.« less

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores

PubMed Central

Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

2016-01-01

The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor’s law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases. PMID:27310915

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

PubMed

Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

2016-01-01

The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Synergistic interactions of ecosystem services: florivorous pest control boosts crop yield increase through insect pollination.

PubMed

Sutter, Louis; Albrecht, Matthias

2016-02-10

Insect pollination and pest control are pivotal functions sustaining global food production. However, they have mostly been studied in isolation and how they interactively shape crop yield remains largely unexplored. Using controlled field experiments, we found strong synergistic effects of insect pollination and simulated pest control on yield quantity and quality. Their joint effect increased yield by 23%, with synergistic effects contributing 10%, while their single contributions were 7% and 6%, respectively. The potential economic benefit for a farmer from the synergistic effects (12%) was 1.8 times greater than their individual contributions (7% each). We show that the principal underlying mechanism was a pronounced pest-induced reduction in flower lifetime, resulting in a strong reduction in the number of pollinator visits a flower receives during its lifetime. Our findings highlight the importance of non-additive interactions among ecosystem services (ES) when valuating, mapping or predicting them and reveal fundamental implications for ecosystem management and policy aimed at maximizing ES for sustainable agriculture. © 2016 The Author(s).

Large-scale production of lentiviral vector in a closed system hollow fiber bioreactor

PubMed Central

Sheu, Jonathan; Beltzer, Jim; Fury, Brian; Wilczek, Katarzyna; Tobin, Steve; Falconer, Danny; Nolta, Jan; Bauer, Gerhard

2015-01-01

Lentiviral vectors are widely used in the field of gene therapy as an effective method for permanent gene delivery. While current methods of producing small scale vector batches for research purposes depend largely on culture flasks, the emergence and popularity of lentiviral vectors in translational, preclinical and clinical research has demanded their production on a much larger scale, a task that can be difficult to manage with the numbers of producer cell culture flasks required for large volumes of vector. To generate a large scale, partially closed system method for the manufacturing of clinical grade lentiviral vector suitable for the generation of induced pluripotent stem cells (iPSCs), we developed a method employing a hollow fiber bioreactor traditionally used for cell expansion. We have demonstrated the growth, transfection, and vector-producing capability of 293T producer cells in this system. Vector particle RNA titers after subsequent vector concentration yielded values comparable to lentiviral iPSC induction vector batches produced using traditional culture methods in 225 cm2 flasks (T225s) and in 10-layer cell factories (CF10s), while yielding a volume nearly 145 times larger than the yield from a T225 flask and nearly three times larger than the yield from a CF10. Employing a closed system hollow fiber bioreactor for vector production offers the possibility of manufacturing large quantities of gene therapy vector while minimizing reagent usage, equipment footprint, and open system manipulation. PMID:26151065

Free-ranging dogs assess the quantity of opponents in intergroup conflicts.

PubMed

Bonanni, Roberto; Natoli, Eugenia; Cafazzo, Simona; Valsecchi, Paola

2011-01-01

In conflicts between social groups, the decision of competitors whether to attack/retreat should be based on the assessment of the quantity of individuals in their own and the opposing group. Experimental studies on numerical cognition in animals suggest that they may represent both large and small numbers as noisy mental magnitudes subject to scalar variability, and small numbers (≤4) also as discrete object-files. Consequently, discriminating between large quantities, but not between smaller ones, should become easier as the asymmetry between quantities increases. Here, we tested these hypotheses by recording naturally occurring conflicts in a population of free-ranging dogs, Canis lupus familiaris, living in a suburban environment. The overall probability of at least one pack member approaching opponents aggressively increased with a decreasing ratio of the number of rivals to that of companions. Moreover, the probability that more than half of the pack members withdrew from a conflict increased when this ratio increased. The skill of dogs in correctly assessing relative group size appeared to improve with increasing the asymmetry in size when at least one pack comprised more than four individuals, and appeared affected to a lesser extent by group size asymmetries when dogs had to compare only small numbers. These results provide the first indications that a representation of quantity based on noisy mental magnitudes may be involved in the assessment of opponents in intergroup conflicts and leave open the possibility that an additional, more precise mechanism may operate with small numbers.

Do Social Conditions Affect Capuchin Monkeys' (Cebus apella) Choices in a Quantity Judgment Task?

PubMed

Beran, Michael J; Perdue, Bonnie M; Parrish, Audrey E; Evans, Theodore A

2012-01-01

Beran et al. (2012) reported that capuchin monkeys closely matched the performance of humans in a quantity judgment test in which information was incomplete but a judgment still had to be made. In each test session, subjects first made quantity judgments between two known options. Then, they made choices where only one option was visible. Both humans and capuchin monkeys were guided by past outcomes, as they shifted from selecting a known option to selecting an unknown option at the point at which the known option went from being more than the average rate of return to less than the average rate of return from earlier choices in the test session. Here, we expanded this assessment of what guides quantity judgment choice behavior in the face of incomplete information to include manipulations to the unselected quantity. We manipulated the unchosen set in two ways: first, we showed the monkeys what they did not get (the unchosen set), anticipating that "losses" would weigh heavily on subsequent trials in which the same known quantity was presented. Second, we sometimes gave the unchosen set to another monkey, anticipating that this social manipulation might influence the risk-taking responses of the focal monkey when faced with incomplete information. However, neither manipulation caused difficulty for the monkeys who instead continued to use the rational strategy of choosing known sets when they were as large as or larger than the average rate of return in the session, and choosing the unknown (riskier) set when the known set was not sufficiently large. As in past experiments, this was true across a variety of daily ranges of quantities, indicating that monkeys were not using some absolute quantity as a threshold for selecting (or not) the known set, but instead continued to use the daily average rate of return to determine when to choose the known versus the unknown quantity.

Quantity Stickiness versus Stackelberg Leadership

NASA Astrophysics Data System (ADS)

Ferreira, F. A.

2008-10-01

We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

High-Yield Secretion of Multiple Client Proteins in Aspergillus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Segato, F.; Damasio, A. R. L.; Goncalves, T. A.

2012-07-15

Production of pure and high-yield client proteins is an important technology that addresses the need for industrial applications of enzymes as well as scientific experiments in protein chemistry and crystallization. Fungi are utilized in industrial protein production because of their ability to secrete large quantities of proteins. In this study, we engineered a high-expression-secretion vector, pEXPYR that directs proteins towards the extracellular medium in two Aspergillii host strains, examine the effect of maltose-induced over-expression and protein secretion as well as time and pH-dependent protein stability in the medium. We describe five client proteins representing a core set of hemicellulose degradingmore » enzymes that accumulated up to 50-100 mg/L of protein. Using a recyclable genetic marker that allows serial insertion of multiple genes, simultaneous hyper-secretion of three client proteins in a single host strain was accomplished.« less

Effects of storage temperature on the quantity and integrity of genomic DNA extracted from mice tissues: A comparison of recovery methods

PubMed Central

Al-Griw, Huda H.; Zraba, Zena A.; Al-Muntaser, Salsabiel K.; Draid, Marwan M.; Zaidi, Aisha M.; Tabagh, Refaat M.; Al-Griw, Mohamed A.

2017-01-01

Efficient extraction of genomic DNA (gDNA) from biological materials found in harsh environments is the first step for successful forensic DNA profiling. This study aimed to evaluate two methods for DNA recovery from animal tissues (livers, muscles), focusing on the best storage temperature for DNA yield in term of quality, quantity, and integrity for use in several downstream molecular techniques. Six male Swiss albino mice were sacrificed, liver and muscle tissues (n=32) were then harvested and stored for one week in different temperatures, -20°C, 4°C, 25°C and 40°C. The conditioned animal tissues were used for DNA extraction by Chelex-100 method or NucleoSpinC Blood and Tissue kit. The extracted gDNA was visualized on 1.5% agarose gel electrophoresis to determine the quality of gDNA and analysed spectrophotometrically to determine the DNA concentration and the purity. Both methods, Chelex-100 and NucleoSpin Blood and Tissue kit found to be appropriate for yielding high quantity of gDNA, with the Chelex 100 method yielding a greater quantity (P < 0.045) than the kit. At -20°C, 4°C, and 25°C temperatures, the concentration of DNA yield was numerically lower than at 40°C. The NucleoSpinC Blood and Tissue kit produced a higher (P=0.031) purity product than the Chelex-100 method, particularly for muscle tissues. The Chelex-100 method is cheap, fast, effective, and is a crucial tool for yielding DNA from animal tissues (livers, muscles) exposed to harsh environment with little limitations. PMID:28884076

The shared and unique values of optical, fluorescence, thermal and microwave satellite data for estimating large-scale crop yields

USDA-ARS?s Scientific Manuscript database

Large-scale crop monitoring and yield estimation are important for both scientific research and practical applications. Satellite remote sensing provides an effective means for regional and global cropland monitoring, particularly in data-sparse regions that lack reliable ground observations and rep...

Varieties of quantity estimation in children.

PubMed

Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

2015-06-01

In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3 children were asked to map continuous quantities, discrete nonsymbolic quantities (numerosities), and symbolic (Arabic) numbers onto a visual line. Numerical quantity was matched for the symbolic and discrete nonsymbolic conditions, whereas cumulative surface area was matched for the continuous and discrete quantity conditions. Crucially, in the discrete condition children's estimation could rely either on the cumulative area or numerosity. All children showed a linear mapping for continuous quantities, whereas a developmental shift from a logarithmic to a linear mapping was observed for both nonsymbolic and symbolic numerical quantities. Analyses on individual estimates suggested the presence of two distinct strategies in estimating discrete nonsymbolic quantities: one based on numerosity and the other based on spatial extent. In Experiment 2, a non-spatial continuous quantity (shades of gray) and new discrete nonsymbolic conditions were added to the set used in Experiment 1. Results confirmed the linear patterns for the continuous tasks, as well as the presence of a subset of children relying on numerosity for the discrete nonsymbolic numerosity conditions despite the availability of continuous visual cues. Overall, our findings demonstrate that estimation of numerical and non-numerical quantities is based on different processing strategies and follow different developmental trajectories. (c) 2015 APA, all rights reserved).

48 CFR 52.236-16 - Quantity Surveys.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 2 2013-10-01 2013-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

48 CFR 52.236-16 - Quantity Surveys.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 2 2011-10-01 2011-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

48 CFR 52.236-16 - Quantity Surveys.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

48 CFR 52.236-16 - Quantity Surveys.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 2 2014-10-01 2014-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

48 CFR 52.236-16 - Quantity Surveys.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Quantity Surveys. 52.236... Quantity Surveys. As prescribed in 36.516, the contracting officer may insert the following clause in... payment based on quantity surveys is contemplated: Quantity Surveys (APR 1984) (a) Quantity surveys shall...

Stand-yield prediction for managed Ocala sand pine

Treesearch

D.L. Rockwood; B. Yang; K.W. Outcalt

1997-01-01

Sand pine is a very important species in Florida, producing significant quantities of fiber. The purpose of this study was to develop the site index and stand-level growth and yield equations managers need to make informed decisions. Data were collected from 35 seeded plots of Ocala sand pine covering a range of site indexes, ages, and densities in 1982-83. These plots...

Spatial derivatives of flow quantities behind curved shocks of all strengths

NASA Technical Reports Server (NTRS)

Darden, C. M.

1984-01-01

Explicit formulas in terms of shock curvature are developed for spatial derivatives of flow quantities behind a curved shock for two-dimensional inviscid steady flow. Factors which yield the equations indeterminate as the shock strength approaches 0 have been cancelled analytically so that formulas are valid for shocks of any strength. An application for the method is shown in the solution of shock coalescence when nonaxisymmetric effects are felt through derivatives in the circumferential direction. The solution of this problem requires flow derivatives behind the shock in both the axial and radial direction.

Feeding Moringa oleifera fresh or ensiled to dairy cows--effects on milk yield and milk flavor.

PubMed

Mendieta-Araica, Bryan; Spörndly, Eva; Reyes-Sánchez, Nadir; Spörndly, Rolf

2011-06-01

Moringa oleifera, either fresh or ensiled, was compared with Elephant grass as a main feedstuff for dairy cows. To test the effects feed had on milk yield, milk composition, ration digestibility, and the organoleptic characteristics of milk, six lactating dairy cows were used in a Changeover 3 × 3 Latin Square experiment, replicated twice. With equal intake of metabolizable energy the intake of protein and fiber differed (p < 0.001) between all diets where fresh Moringa had the highest and the Elephant grass diet had the lowest intake. Compared with the control diet, ensiled Moringa had higher digestibility (P < 0.05) of both protein and fiber. With the exception of DM digestibility, no digestibility differences were found between fresh Moringa and Moringa silage treatments. Milk yield did not differ between any of the treatments and averaged 13.7 kg cow day(-1). Milk composition was similar among all treatments. Milk from the fresh Moringa treatment, however, had a grassy flavor and aroma, significantly different from the other two treatments, even though it was normal in color and appearance. No organoleptic differences were found between milk from the control treatment and the Moringa silage treatment. The conclusion is that Moringa silage can be fed to dairy cows in large quantities to produce the same quantity and quality of milk as traditional diets.

Simulation of fatigue crack growth under large scale yielding conditions

NASA Astrophysics Data System (ADS)

Schweizer, Christoph; Seifert, Thomas; Riedel, Hermann

2010-07-01

A simple mechanism based model for fatigue crack growth assumes a linear correlation between the cyclic crack-tip opening displacement (ΔCTOD) and the crack growth increment (da/dN). The objective of this work is to compare analytical estimates of ΔCTOD with results of numerical calculations under large scale yielding conditions and to verify the physical basis of the model by comparing the predicted and the measured evolution of the crack length in a 10%-chromium-steel. The material is described by a rate independent cyclic plasticity model with power-law hardening and Masing behavior. During the tension-going part of the cycle, nodes at the crack-tip are released such that the crack growth increment corresponds approximately to the crack-tip opening. The finite element analysis performed in ABAQUS is continued for so many cycles until a stabilized value of ΔCTOD is reached. The analytical model contains an interpolation formula for the J-integral, which is generalized to account for cyclic loading and crack closure. Both simulated and estimated ΔCTOD are reasonably consistent. The predicted crack length evolution is found to be in good agreement with the behavior of microcracks observed in a 10%-chromium steel.

Quantity discounts on a virtual good: The results of a massive pricing experiment at King Digital Entertainment

PubMed Central

Levitt, Steven D.; List, John A.; Neckermann, Susanne; Nelson, David

2016-01-01

We report on a natural field experiment on quantity discounts involving more than 14 million consumers. Implementing price reductions ranging from 9–70% for large purchases, we found remarkably little impact on revenue, either positively or negatively. There was virtually no increase in the quantity of customers making a purchase; all the observed changes occurred for customers who already were buyers. We found evidence that infrequent purchasers are more responsive to discounts than frequent purchasers. There was some evidence of habit formation when prices returned to pre-experiment levels. There also was some evidence that consumers contemplating small purchases are discouraged by the presence of extreme quantity discounts for large purchases. PMID:27382146

Molecular dynamics simulations with electronic stopping can reproduce experimental sputtering yields of metals impacted by large cluster ions

NASA Astrophysics Data System (ADS)

Tian, Jiting; Zhou, Wei; Feng, Qijie; Zheng, Jian

2018-03-01

An unsolved problem in research of sputtering from metals induced by energetic large cluster ions is that molecular dynamics (MD) simulations often produce sputtering yields much higher than experimental results. Different from the previous simulations considering only elastic atomic interactions (nuclear stopping), here we incorporate inelastic electrons-atoms interactions (electronic stopping, ES) into MD simulations using a friction model. In this way we have simulated continuous 45° impacts of 10-20 keV C60 on a Ag(111) surface, and found that the calculated sputtering yields can be very close to the experimental results when the model parameter is appropriately assigned. Conversely, when we ignore the effect of ES, the yields are much higher, just like the previous studies. We further expand our research to the sputtering of Au induced by continuous keV C60 or Ar100 bombardments, and obtain quite similar results. Our study indicates that the gap between the experimental and the simulated sputtering yields is probably induced by the ignorance of ES in the simulations, and that a careful treatment of this issue is important for simulations of cluster-ion-induced sputtering, especially for those aiming to compare with experiments.

Controls on Stormwater Runoff Quality and Quantity in Semi-arid, Urban Catchments

NASA Astrophysics Data System (ADS)

Gallo, E. L.; Brooks, P. D.; Lohse, K. A.

2009-12-01

Utilization of recharged urban runoff to complement municipal water supply has gained importance in arid regions where populations and their urban footprint continue to grow, and where water resources are scarce. However, our understanding of how runoff quantity and quality respond to urbanization in arid landscapes is largely incomplete and poses a challenge for water resources management. Here we address the question: What controls the hydrologic and hydrochemical responses of arid urban catchments? We collected water samples and stream stage data from 5 urban catchments of varied land uses (low, medium and high density residential, mixed and commercial land use) in southern Arizona during the summer rainfall seasons of 2007 and 2008. The most homogeneous catchments, as indicated by the index of landscape heterogeneity, were the least and most impervious, while the most heterogeneous sites had mid-range imperviousness. Hydrochemical responses were mixed, did not correlate with imperviousness or vegetation abundance, and were not strongly controlled by land use. Clustering analysis highlight hydrologic and sourcing controls on hydrochemistry, specifically conservative solute transport, land use specific and geologic solute sourcing and atmospheric deposition. Overall, water yields were surprisingly small (< 15%) and increased with imperviousness. Our data show that discharge responses were more sensitive to rainfall magnitude in homogeneous sites. We suggest that imperviousness and rainfall magnitude control water yields; whereas landscape heterogeneity may control a catchment’s sensitivity to generate runoff. The coupling of landscape and hydrology in controlling hydrochemistry is well illustrated by chloride (Cl), a non-reactive hydrologic tracer that was positively correlated with a large number of solutes such as ammonium, dissolved organic carbon, cadmium and zinc. We observed the highest concentrations and coefficients of variation of Cl at least and most

48 CFR 36.516 - Quantity surveys.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

48 CFR 36.516 - Quantity surveys.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

48 CFR 36.516 - Quantity surveys.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

48 CFR 36.516 - Quantity surveys.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

48 CFR 36.516 - Quantity surveys.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Quantity surveys. 36.516... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.516 Quantity surveys. The contracting officer may insert the clause at 52.236-16, Quantity Surveys, in solicitations and contracts when...

Radiation quantities and units

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-04-15

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations inmore » subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25(4) required an extension of Part B.« less

14 CFR 27.1551 - Oil quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 29.1551 - Oil quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 27.1551 - Oil quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 29.1551 - Oil quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 27.1551 - Oil quantity indicator.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 29.1551 - Oil quantity indicator.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 29.1551 Section 29... Placards § 29.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

14 CFR 27.1551 - Oil quantity indicator.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 27.1551 Section 27... § 27.1551 Oil quantity indicator. Each oil quantity indicator must be marked with enough increments to indicate readily and accurately the quantity of oil. ...

Quantitative analysis of relationships between irradiation parameters and the reproducibility of cyclotron-produced (99m)Tc yields.

PubMed

Tanguay, J; Hou, X; Buckley, K; Schaffer, P; Bénard, F; Ruth, T J; Celler, A

2015-05-21

Cyclotron production of (99m)Tc through the (100)Mo(p,2n) (99m)Tc reaction channel is actively being investigated as an alternative to reactor-based (99)Mo generation by nuclear fission of (235)U. An exciting aspect of this approach is that it can be implemented using currently-existing cyclotron infrastructure to supplement, or potentially replace, conventional (99m)Tc production methods that are based on aging and increasingly unreliable nuclear reactors. Successful implementation will require consistent production of large quantities of high-radionuclidic-purity (99m)Tc. However, variations in proton beam currents and the thickness and isotopic composition of enriched (100)Mo targets, in addition to other irradiation parameters, may degrade reproducibility of both radionuclidic purity and absolute (99m)Tc yields. The purpose of this article is to present a method for quantifying relationships between random variations in production parameters, including (100)Mo target thicknesses and proton beam currents, and reproducibility of absolute (99m)Tc yields (defined as the end of bombardment (EOB) (99m)Tc activity). Using the concepts of linear error propagation and the theory of stochastic point processes, we derive a mathematical expression that quantifies the influence of variations in various irradiation parameters on yield reproducibility, quantified in terms of the coefficient of variation of the EOB (99m)Tc activity. The utility of the developed formalism is demonstrated with an example. We show that achieving less than 20% variability in (99m)Tc yields will require highly-reproducible target thicknesses and proton currents. These results are related to the service rate which is defined as the percentage of (99m)Tc production runs that meet the minimum daily requirement of one (or many) nuclear medicine departments. For example, we show that achieving service rates of 84.0%, 97.5% and 99.9% with 20% variations in target thicknesses requires producing on average

Quantitative analysis of relationships between irradiation parameters and the reproducibility of cyclotron-produced 99mTc yields

NASA Astrophysics Data System (ADS)

Tanguay, J.; Hou, X.; Buckley, K.; Schaffer, P.; Bénard, F.; Ruth, T. J.; Celler, A.

2015-05-01

Cyclotron production of 99mTc through the 100Mo(p,2n) 99mTc reaction channel is actively being investigated as an alternative to reactor-based 99Mo generation by nuclear fission of 235U. An exciting aspect of this approach is that it can be implemented using currently-existing cyclotron infrastructure to supplement, or potentially replace, conventional 99mTc production methods that are based on aging and increasingly unreliable nuclear reactors. Successful implementation will require consistent production of large quantities of high-radionuclidic-purity 99mTc. However, variations in proton beam currents and the thickness and isotopic composition of enriched 100Mo targets, in addition to other irradiation parameters, may degrade reproducibility of both radionuclidic purity and absolute 99mTc yields. The purpose of this article is to present a method for quantifying relationships between random variations in production parameters, including 100Mo target thicknesses and proton beam currents, and reproducibility of absolute 99mTc yields (defined as the end of bombardment (EOB) 99mTc activity). Using the concepts of linear error propagation and the theory of stochastic point processes, we derive a mathematical expression that quantifies the influence of variations in various irradiation parameters on yield reproducibility, quantified in terms of the coefficient of variation of the EOB 99mTc activity. The utility of the developed formalism is demonstrated with an example. We show that achieving less than 20% variability in 99mTc yields will require highly-reproducible target thicknesses and proton currents. These results are related to the service rate which is defined as the percentage of 99mTc production runs that meet the minimum daily requirement of one (or many) nuclear medicine departments. For example, we show that achieving service rates of 84.0%, 97.5% and 99.9% with 20% variations in target thicknesses requires producing on average 1.2, 1.5 and 1.9 times the

The accuracy of less: Natural bounds explain why quantity decreases are estimated more accurately than quantity increases.

PubMed

Chandon, Pierre; Ordabayeva, Nailya

2017-02-01

Five studies show that people, including experts such as professional chefs, estimate quantity decreases more accurately than quantity increases. We argue that this asymmetry occurs because physical quantities cannot be negative. Consequently, there is a natural lower bound (zero) when estimating decreasing quantities but no upper bound when estimating increasing quantities, which can theoretically grow to infinity. As a result, the "accuracy of less" disappears (a) when a numerical or a natural upper bound is present when estimating quantity increases, or (b) when people are asked to estimate the (unbounded) ratio of change from 1 size to another for both increasing and decreasing quantities. Ruling out explanations related to loss aversion, symbolic number mapping, and the visual arrangement of the stimuli, we show that the "accuracy of less" influences choice and demonstrate its robustness in a meta-analysis that includes previously published results. Finally, we discuss how the "accuracy of less" may explain asymmetric reactions to the supersizing and downsizing of food portions, some instances of the endowment effect, and asymmetries in the perception of increases and decreases in physical and psychological distance. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

14 CFR 23.1551 - Oil quantity indicator.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

14 CFR 23.1551 - Oil quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

14 CFR 23.1551 - Oil quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

14 CFR 23.1551 - Oil quantity indicator.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indicator. 23.1551 Section 23... Information Markings and Placards § 23.1551 Oil quantity indicator. Each oil quantity indicator must be marked in sufficient increments to indicate readily and accurately the quantity of oil. ...

Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

NASA Astrophysics Data System (ADS)

Roşu, M. M.; Tarbă, C. I.; Neagu, C.

2016-11-01

The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

30 CFR 75.325 - Air quantity.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working face...

14 CFR 25.1551 - Oil quantity indication.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

14 CFR 25.1551 - Oil quantity indication.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

14 CFR 25.1551 - Oil quantity indication.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

14 CFR 25.1551 - Oil quantity indication.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Oil quantity indication. 25.1551 Section 25... Placards § 25.1551 Oil quantity indication. Each oil quantity indicating means must be marked to indicate the quantity of oil readily and accurately. [Amdt. 25-72, 55 FR 29786, July 20, 1990] ...

FURFURAL YIELD AND DECOMPOSITION IN SODIUM 2,4DIMETHYLBENZENESULFONATE--SULFURIC ACID--WATER SOLUTIONS.

DTIC Science & Technology

Batch-type microreactors (about 1/40 milliliter of reactants) were used to measure furfural yields from acidified xylose solutions containing sodium...It was found that presence of the salt did not affect the quantity of furfural produced, but greatly increased the rate of formation. The regular...increase in rate of furfural formation was directly related to the increase in the rate xylose decomposition, and furfural yields for all salt and acid

Find_tfSBP: find thermodynamics-feasible and smallest balanced pathways with high yield from large-scale metabolic networks.

PubMed

Xu, Zixiang; Sun, Jibin; Wu, Qiaqing; Zhu, Dunming

2017-12-11

Biologically meaningful metabolic pathways are important references in the design of industrial bacterium. At present, constraint-based method is the only way to model and simulate a genome-scale metabolic network under steady-state criteria. Due to the inadequate assumption of the relationship in gene-enzyme-reaction as one-to-one unique association, computational difficulty or ignoring the yield from substrate to product, previous pathway finding approaches can't be effectively applied to find out the high yield pathways that are mass balanced in stoichiometry. In addition, the shortest pathways may not be the pathways with high yield. At the same time, a pathway, which exists in stoichiometry, may not be feasible in thermodynamics. By using mixed integer programming strategy, we put forward an algorithm to identify all the smallest balanced pathways which convert the source compound to the target compound in large-scale metabolic networks. The resulting pathways by our method can finely satisfy the stoichiometric constraints and non-decomposability condition. Especially, the functions of high yield and thermodynamics feasibility have been considered in our approach. This tool is tailored to direct the metabolic engineering practice to enlarge the metabolic potentials of industrial strains by integrating the extensive metabolic network information built from systems biology dataset.

Large-scale Assessment Yields Evidence of Minimal Use of Reasoning Skills in Traditionally Taught Classes

NASA Astrophysics Data System (ADS)

Thacker, Beth

2017-01-01

Large-scale assessment data from Texas Tech University yielded evidence that most students taught traditionally in large lecture classes with online homework and predominantly multiple choice question exams, when asked to answer free-response (FR) questions, did not support their answers with logical arguments grounded in physics concepts. In addition to a lack of conceptual understanding, incorrect and partially correct answers lacked evidence of the ability to apply even lower level reasoning skills in order to solve a problem. Correct answers, however, did show evidence of at least lower level thinking skills as coded using a rubric based on Bloom's taxonomy. With the introduction of evidence-based instruction into the labs and recitations of the large courses and in a small, completely laboratory-based, hands-on course, the percentage of correct answers with correct explanations increased. The FR format, unlike other assessment formats, allowed assessment of both conceptual understanding and the application of thinking skills, clearly pointing out weaknesses not revealed by other assessment instruments, and providing data on skills beyond conceptual understanding for course and program assessment. Supported by National Institutes of Health (NIH) Challenge grant #1RC1GM090897-01.

High-Yield Synthesis of Stoichiometric Boron Nitride Nanostructures

DOE PAGES

Nocua, José E.; Piazza, Fabrice; Weiner, Brad R.; ...

2009-01-01

Boron nimore » tride (BN) nanostructures are structural analogues of carbon nanostructures but have completely different bonding character and structural defects. They are chemically inert, electrically insulating, and potentially important in mechanical applications that include the strengthening of light structural materials. These applications require the reliable production of bulk amounts of pure BN nanostructures in order to be able to reinforce large quantities of structural materials, hence the need for the development of high-yield synthesis methods of pure BN nanostructures. Using borazine ( B 3 N 3 H 6 ) as chemical precursor and the hot-filament chemical vapor deposition (HFCVD) technique, pure BN nanostructures with cross-sectional sizes ranging between 20 and 50 nm were obtained, including nanoparticles and nanofibers. Their crystalline structure was characterized by (XRD), their morphology and nanostructure was examined by (SEM) and (TEM), while their chemical composition was studied by (EDS), (FTIR), (EELS), and (XPS). Taken altogether, the results indicate that all the material obtained is stoichiometric nanostructured BN with hexagonal and rhombohedral crystalline structure.« less

Modelling Pasture-based Automatic Milking System Herds: The Impact of Large Herd on Milk Yield and Economics.

PubMed

Islam, M R; Clark, C E F; Garcia, S C; Kerrisk, K L

2015-07-01

The aim of this modelling study was to investigate the effect of large herd size (and land areas) on walking distances and milking interval (MI), and their impact on milk yield and economic penalties when 50% of the total diets were provided from home grown feed either as pasture or grazeable complementary forage rotation (CFR) in an automatic milking system (AMS). Twelve scenarios consisting of 3 AMS herds (400, 600, 800 cows), 2 levels of pasture utilisation (current AMS utilisation of 15.0 t dry matter [DM]/ha, termed as 'moderate'; optimum pasture utilisation of 19.7 t DM/ha, termed as 'high') and 2 rates of incorporation of grazeable complementary forage system (CFS: 0, 30%; CFS = 65% farm is CFR and 35% of farm is pasture) were investigated. Walking distances, energy loss due to walking, MI, reduction in milk yield and income loss were calculated for each treatment based on information available in the literature. With moderate pasture utilisation and 0% CFR, increasing the herd size from 400 to 800 cows resulted in an increase in total walking distances between the parlour and the paddock from 3.5 to 6.3 km. Consequently, MI increased from 15.2 to 16.4 h with increased herd size from 400 to 800 cows. High pasture utilisation (allowing for an increased stocking density) reduced the total walking distances up to 1 km, thus reduced the MI by up to 0.5 h compared to the moderate pasture, 800 cow herd combination. The high pasture utilisation combined with 30% of the farm in CFR in the farm reduced the total walking distances by up to 1.7 km and MI by up to 0.8 h compared to the moderate pasture and 800 cow herd combination. For moderate pasture utilisation, increasing the herd size from 400 to 800 cows resulted in more dramatic milk yield penalty as yield increasing from c.f. 2.6 and 5.1 kg/cow/d respectively, which incurred a loss of up to $AU 1.9/cow/d. Milk yield losses of 0.61 kg and 0.25 kg for every km increase in total walking distance (voluntary return

99Mo Yield Using Large Sample Mass of MoO3 for Sustainable Production of 99Mo

NASA Astrophysics Data System (ADS)

Tsukada, Kazuaki; Nagai, Yasuki; Hashimoto, Kazuyuki; Kawabata, Masako; Minato, Futoshi; Saeki, Hideya; Motoishi, Shoji; Itoh, Masatoshi

2018-04-01

A neutron source from the C(d,n) reaction has the unique capability of producing medical radioisotopes such as 99Mo with a minimum level of radioactive waste. Precise data on the neutron flux are crucial to determine the best conditions for obtaining the maximum yield of 99Mo. The measured yield of 99Mo produced by the 100Mo(n,2n)99Mo reaction from a large sample mass of MoO3 agrees well with the numerical result estimated with the latest neutron data, which are a factor of two larger than the other existing data. This result establishes an important finding for the domestic production of 99Mo: approximately 50% of the demand for 99Mo in Japan could be met using a 100 g 100MoO3 sample mass with a single accelerator of 40 MeV, 2 mA deuteron beams.

Resonant Scanning with Large Field of View Reduces Photobleaching and Enhances Fluorescence Yield in STED Microscopy.

PubMed

Wu, Yong; Wu, Xundong; Lu, Rong; Zhang, Jin; Toro, Ligia; Stefani, Enrico

2015-10-01

Photobleaching is a major limitation of superresolution Stimulated Depletion Emission (STED) microscopy. Fast scanning has long been considered an effective means to reduce photobleaching in fluorescence microscopy, but a careful quantitative study of this issue is missing. In this paper, we show that the photobleaching rate in STED microscopy can be slowed down and the fluorescence yield be enhanced by scanning with high speed, enabled by using large field of view in a custom-built resonant-scanning STED microscope. The effect of scanning speed on photobleaching and fluorescence yield is more remarkable at higher levels of depletion laser irradiance, and virtually disappears in conventional confocal microscopy. With ≥6 GW∙cm(-2) depletion irradiance, we were able to extend the fluorophore survival time of Atto 647N and Abberior STAR 635P by ~80% with 8-fold wider field of view. We confirm that STED Photobleaching is primarily caused by the depletion light acting upon the excited fluorophores. Experimental data agree with a theoretical model. Our results encourage further increasing the linear scanning speed for photobleaching reduction in STED microscopy.

Quantities of Arsenic-Treated Wood in Demolition Debris Generated by Hurricane Katrina

PubMed Central

Dubey, Brajesh; Solo-Gabriele, Helena M.; Townsend, Timothy G.

2008-01-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood. PMID:17396637

Large-scale preparation of plasmid DNA.

PubMed

Heilig, J S; Elbing, K L; Brent, R

2001-05-01

Although the need for large quantities of plasmid DNA has diminished as techniques for manipulating small quantities of DNA have improved, occasionally large amounts of high-quality plasmid DNA are desired. This unit describes the preparation of milligram quantities of highly purified plasmid DNA. The first part of the unit describes three methods for preparing crude lysates enriched in plasmid DNA from bacterial cells grown in liquid culture: alkaline lysis, boiling, and Triton lysis. The second part describes four methods for purifying plasmid DNA in such lysates away from contaminating RNA and protein: CsCl/ethidium bromide density gradient centrifugation, polyethylene glycol (PEG) precipitation, anion-exchange chromatography, and size-exclusion chromatography.

High-throughput and high-yield fabrication of uniaxially-aligned chitosan-based nanofibers by centrifugal electrospinning

PubMed Central

Erickson, Ariane E.; Edmondson, Dennis; Chang, Fei-Chien; Wood, Dave; Gong, Alex; Levengood, Sheeny Lan; Zhang, Miqin

2016-01-01

The inability to produce large quantities of nanofibers has been a primary obstacle in advancement and commercialization of electrospinning technologies, especially when aligned nanofibers are desired. Here, we present a high-throughput centrifugal electrospinning (HTP-CES) system capable of producing a large number of highly-aligned nanofiber samples with high-yield and tunable diameters. The versatility of the design was revealed when bead-less nanofibers were produced from copolymer chitosan/polycaprolactone (C-PCL) solutions despite variations in polymer blend composition or spinneret needle gauge. Compared to conventional electrospinning techniques, fibers spun with the HTP-CES not only exhibited superior alignment, but also better diameter uniformity. Nanofiber alignment was quantified using Fast Fourier Transform (FFT) analysis. In addition, a concave correlation between the needle diameter and resultant fiber diameter was identified. This system can be easily scaled up for industrial production of highly-aligned nanofibers with tunable diameters that can potentially meet the requirements for various engineering and biomedical applications. PMID:26428148

Scaling beta-delayed neutron measurements to large detector areas

NASA Astrophysics Data System (ADS)

Sutanto, F.; Nattress, J.; Jovanovic, I.

2017-08-01

We explore the performance of a cargo screening system that consists of two large-sized composite scintillation detectors and a high-energy neutron interrogation source by modeling and simulation. The goal of the system is to measure β-delayed neutron emission from an illicit special nuclear material by use of active interrogation. This task is challenging because the β-delayed neutron yield is small in comparison with the yield of the prompt fission secondary products, β-delayed neutrons are emitted with relatively low energies, and high neutron and gamma backgrounds are typically present. Detectors used to measure delayed neutron emission must exhibit high intrinsic efficiency and cover a large solid angle, which also makes them sensitive to background neutron radiation. We present a case study where we attempt to detect the presence of 5 kg-scale quantities of 235U in a standard air-filled cargo container using 14 MeV neutrons as a probe. We find that by using a total measurement time of ˜11.6 s and a dose equivalent of ˜1.7 mrem, the presence of 235U can be detected with false positive and false negative probabilities that are both no larger than 0.1%.

A Semi-Vectorization Algorithm to Synthesis of Gravitational Anomaly Quantities on the Earth

NASA Astrophysics Data System (ADS)

Abdollahzadeh, M.; Eshagh, M.; Najafi Alamdari, M.

2009-04-01

The Earth's gravitational potential can be expressed by the well-known spherical harmonic expansion. The computational time of summing up this expansion is an important practical issue which can be reduced by an efficient numerical algorithm. This paper proposes such a method for block-wise synthesizing the anomaly quantities on the Earth surface using vectorization. Fully-vectorization means transformation of the summations to the simple matrix and vector products. It is not a practical for the matrices with large dimensions. Here a semi-vectorization algorithm is proposed to avoid working with large vectors and matrices. It speeds up the computations by using one loop for the summation either on degrees or on orders. The former is a good option to synthesize the anomaly quantities on the Earth surface considering a digital elevation model (DEM). This approach is more efficient than the two-step method which computes the quantities on the reference ellipsoid and continues them upward to the Earth surface. The algorithm has been coded in MATLAB which synthesizes a global grid of 5′Ã- 5′ (corresponding 9 million points) of gravity anomaly or geoid height using a geopotential model to degree 360 in 10000 seconds by an ordinary computer with 2G RAM.

40 CFR 201.21 - Quantities measured.

Code of Federal Regulations, 2011 CFR

2011-07-01

... § 201.21 Quantities measured. The quantities to be measured under the test conditions described below, are the A-weighted sound levels for “fast” or “slow” meter response as defined in the American...

40 CFR 201.21 - Quantities measured.

Code of Federal Regulations, 2010 CFR

2010-07-01

... § 201.21 Quantities measured. The quantities to be measured under the test conditions described below, are the A-weighted sound levels for “fast” or “slow” meter response as defined in the American...

PACKAGING CERTIFICATION PROGRAM METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan, S.; Loftin, B.; Abramczyk, G.

The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials, under both normal and accident conditions, to perform the essential functions of material containment, subcriticality, and maintain external radiation levels withinmore » the specified limits. By placing the contents in a helium leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large dose rate outside the package. Quantifying the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings provides bounding shielding calculations that define mass limits compliant with 10 CFR 71.47 for a set of proposed SGQ isotopes. The approach is based on energy superposition with dose response calculated for a set of spectral groups for a baseline physical packaging configuration. The methodology includes using the MCNP radiation transport code to evaluate a family of neutron and photon spectral groups using the 9977 shipping package and its associated shielded containers as the base case. This results in a set of multipliers for 'dose per particle

Extracting DNA from 'jaws': high yield and quality from archived tiger shark (Galeocerdo cuvier) skeletal material.

PubMed

Nielsen, E E; Morgan, J A T; Maher, S L; Edson, J; Gauthier, M; Pepperell, J; Holmes, B J; Bennett, M B; Ovenden, J R

2017-05-01

Archived specimens are highly valuable sources of DNA for retrospective genetic/genomic analysis. However, often limited effort has been made to evaluate and optimize extraction methods, which may be crucial for downstream applications. Here, we assessed and optimized the usefulness of abundant archived skeletal material from sharks as a source of DNA for temporal genomic studies. Six different methods for DNA extraction, encompassing two different commercial kits and three different protocols, were applied to material, so-called bio-swarf, from contemporary and archived jaws and vertebrae of tiger sharks (Galeocerdo cuvier). Protocols were compared for DNA yield and quality using a qPCR approach. For jaw swarf, all methods provided relatively high DNA yield and quality, while large differences in yield between protocols were observed for vertebrae. Similar results were obtained from samples of white shark (Carcharodon carcharias). Application of the optimized methods to 38 museum and private angler trophy specimens dating back to 1912 yielded sufficient DNA for downstream genomic analysis for 68% of the samples. No clear relationships between age of samples, DNA quality and quantity were observed, likely reflecting different preparation and storage methods for the trophies. Trial sequencing of DNA capture genomic libraries using 20 000 baits revealed that a significant proportion of captured sequences were derived from tiger sharks. This study demonstrates that archived shark jaws and vertebrae are potential high-yield sources of DNA for genomic-scale analysis. It also highlights that even for similar tissue types, a careful evaluation of extraction protocols can vastly improve DNA yield. © 2016 John Wiley & Sons Ltd.

Impacts of forest restoration on water yield: A systematic review

PubMed Central

Filoso, Solange; Bezerra, Maíra Ometto; Weiss, Katherine C. B.; Palmer, Margaret A.

2017-01-01

Background Enhancing water provision services is a common target in forest restoration projects worldwide due to growing concerns over freshwater scarcity. However, whether or not forest cover expansion or restoration can improve water provision services is still unclear and highly disputed. Purpose The goal of this review is to provide a balanced and impartial assessment of the impacts of forest restoration and forest cover expansion on water yields as informed by the scientific literature. Potential sources of bias on the results of papers published are also examined. Data sources English, Spanish and Portuguese peer-review articles in Agricola, CAB Abstracts, ISI Web of Science, JSTOR, Google Scholar, and SciELO. Databases were searched through 2015. Search terms Intervention terms included forest restoration, regeneration/regrowth, forest second-growth, forestation/afforestation, and forestry. Target terms included water yield/quantity, streamflow, discharge, channel runoff, and annual flow. Study selection and eligibility criteria Articles were pre-selected based on key words in the title, abstract or text. Eligible articles addressed relevant interventions and targets and included quantitative information. Results Most studies reported decreases in water yields following the intervention, while other hydrological benefits have been observed. However, relatively few studies focused specifically on forest restoration, especially with native species, and/or on projects done at large spatial or temporal scales. Information is especially limited for the humid tropics and subtropics. Conclusions and implications of key findings While most studies reported a decrease in water yields, meta-analyses from a sub-set of studies suggest the potential influence of temporal and/or spatial scales on the outcomes of forest cover expansion or restoration projects. Given the many other benefits of forest restoration, improving our understanding of when and why forest

Method for the rapid synthesis of large quantities of metal oxide nanowires at low temperatures

DOEpatents

Sunkara, Mahendra Kumar [Louisville, KY; Vaddiraju, Sreeram [Mountain View, CA; Mozetic, Miran [Ljubljan, SI; Cvelbar, Uros [Idrija, SI

2009-09-22

A process for the rapid synthesis of metal oxide nanoparticles at low temperatures and methods which facilitate the fabrication of long metal oxide nanowires. The method is based on treatment of metals with oxygen plasma. Using oxygen plasma at low temperatures allows for rapid growth unlike other synthesis methods where nanomaterials take a long time to grow. Density of neutral oxygen atoms in plasma is a controlling factor for the yield of nanowires. The oxygen atom density window differs for different materials. By selecting the optimal oxygen atom density for various materials the yield can be maximized for nanowire synthesis of the metal.

Climate Change Impact Uncertainties for Maize in Panama: Farm Information, Climate Projections, and Yield Sensitivities

NASA Technical Reports Server (NTRS)

Ruane, Alex C.; Cecil, L. Dewayne; Horton, Radley M.; Gordon, Roman; McCollum, Raymond (Brown, Douglas); Brown, Douglas; Killough, Brian; Goldberg, Richard; Greeley, Adam P.; Rosenzweig, Cynthia

2011-01-01

We present results from a pilot project to characterize and bound multi-disciplinary uncertainties around the assessment of maize (Zea mays) production impacts using the CERES-Maize crop model in a climate-sensitive region with a variety of farming systems (Panama). Segunda coa (autumn) maize yield in Panama currently suffers occasionally from high water stress at the end of the growing season, however under future climate conditions warmer temperatures accelerate crop maturation and elevated CO (sub 2) concentrations improve water retention. This combination reduces end-of-season water stresses and eventually leads to small mean yield gains according to median projections, although accelerated maturation reduces yields in seasons with low water stresses. Calibrations of cultivar traits, soil profile, and fertilizer amounts are most important for representing baseline yields, however sensitivity to all management factors is reduced in an assessment of future yield changes (most dramatically for fertilizers), suggesting that yield changes may be more generalizable than absolute yields. Uncertainty around General Circulation Model (GCM)s' projected changes in rainfall gain in importance throughout the century, with yield changes strongly correlated with growing season rainfall totals. Climate changes are expected to be obscured by the large inter-annual variations in Panamanian climate that will continue to be the dominant influence on seasonal maize yield into the coming decades. The relatively high (A2) and low (B1) emissions scenarios show little difference in their impact on future maize yields until the end of the century. Uncertainties related to the sensitivity of CERES-Maize to carbon dioxide concentrations have a substantial influence on projected changes, and remain a significant obstacle to climate change impacts assessment. Finally, an investigation into the potential of simple statistical yield emulators based upon key climate variables characterizes the

Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

NASA Astrophysics Data System (ADS)

Ivanov, Kamen G.; Pavlis, Nikolaos K.; Petrushev, Pencho

2017-12-01

Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly ζ , gravity anomaly Δ g , gravity disturbance δ g , north-south deflection of the vertical ξ , east-west deflection of the vertical η , and the second radial derivative T_{rr} of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed 10^{-6} and the memory (RAM) use is 9.3 GB.

The importance of key floral bioactive compounds to honey bees for the detection and attraction of hybrid vegetable crops and increased seed yield.

PubMed

Mas, Flore; Harper, Aimee; Horner, Rachael; Welsh, Taylor; Jaksons, Peter; Suckling, David M

2018-02-15

Crop breeding programmes generally select for traits for improved yield and human consumption preferences. Yet, they often overlook one fundamental trait essential for insect-pollinated crops: pollinator attraction. This is even more critical for hybrid plants that rely on cross-pollination between the male-fertile line and the male-sterile line to set seeds. This study investigated the role of floral odours for honey bee pollination that could explain the poor seed yield in hybrid crops. The key floral bioactive compounds that honey bees detect were identified for three vegetable hybrid crops. It was found that 30% of the variation in bioactive compound quantities was explained by variety. Differences in quantities of the bioactive compounds triggered different degrees of olfactory response and were also associated with varied appetitive response. Correlating the abundance of each bioactive compound with seed yield, it was found that aldehydes such as nonanal and decanal can have a strong negative influence on seed yield with increasing quantity. Using these methodologies to identify relevant bioactive compounds associated with honey bee pollination, plant breeding programmes should also consider selecting for floral traits attractive to honey bees to improve crop pollination for enhanced seed yield. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Thermodynamics of quantum systems with multiple conserved quantities

PubMed Central

Guryanova, Yelena; Popescu, Sandu; Short, Anthony J.; Silva, Ralph; Skrzypczyk, Paul

2016-01-01

Recently, there has been much progress in understanding the thermodynamics of quantum systems, even for small individual systems. Most of this work has focused on the standard case where energy is the only conserved quantity. Here we consider a generalization of this work to deal with multiple conserved quantities. Each conserved quantity, which, importantly, need not commute with the rest, can be extracted and stored in its own battery. Unlike the standard case, in which the amount of extractable energy is constrained, here there is no limit on how much of any individual conserved quantity can be extracted. However, other conserved quantities must be supplied, and the second law constrains the combination of extractable quantities and the trade-offs between them. We present explicit protocols that allow us to perform arbitrarily good trade-offs and extract arbitrarily good combinations of conserved quantities from individual quantum systems. PMID:27384384

Significantly improving the yield of recombinant proteins in Bacillus subtilis by a novel powerful mutagenesis tool (ARTP): Alkaline α-amylase as a case study.

PubMed

Ma, Yingfang; Yang, Haiquan; Chen, Xianzhong; Sun, Bo; Du, Guocheng; Zhou, Zhemin; Song, Jiangning; Fan, You; Shen, Wei

2015-10-01

In this study, atmospheric and room temperature plasma (ARTP), a promising mutation breeding technique, was successfully applied to generate Bacillus subtilis mutants that yielded large quantities of recombinant protein. The high throughput screening platform was implemented to select those mutants with the highest yield of recombinant alkaline α-amylase (AMY), including the preferred mutant B. subtilis WB600 mut-12#. The yield and productivity of recombinant AMY in B. subtilis WB600 mut-12# increased 35.0% and 8.8%, respectively, the extracellular protein concentration of which increased 37.9%. B. subtilis WB600 mut-12# exhibited good genetic stability. Cells from B. subtilis WB600 mut-12# became shorter and wider than those from the wild-type. This study is the first to report a novel powerful mutagenesis tool (ARTP) that significantly improves the yield of recombinant proteins in B. subtilis and may therefore play an important role in the high expression level of proteins in recombinant microbial hosts. Copyright © 2015 Elsevier Inc. All rights reserved.

[Study on High-yield Cultivation Measures for Arctii Fructus].

PubMed

Liu, Shi-yong; Jiang, Xiao-bo; Wang, Tao; Sun, Ji-ye; Hu, Shang-qin; Zhang, Li

2015-02-01

To find out the high yield cultivation measures for Arctii Fructus. Completely randomized block experiment design method was used in the field planting, to analyze the effect of different cultivation way on agronomic characters, phenological phase,quality and quantity of Arctii Fructus. Arctium lappa planted on August 28 had the best results of plant height, thousand seeds weight and yield. The highest yield of Arctii Fructus was got at the density of 1,482 plants/667 m2. Arctiin content was in an increase trend with the planting time delay and planting density increasing. The plant height, thousand seeds weight, yield and arctiin content by split application of fertilizer were significantly higher than that by one-time fertilization. Compared with open field Arctium lappa, plant height, yield, arctiin content and relative water content of plastic film mulching Arctium lappa was higher by 7.74%, 10.87%, 6.38% and 24.20%, respectively. In the topping Arctium lappa, the yield was increased by 11.09%, with 39. 89% less branching number. Early planting time and topping shortened the growth cycle of Arctium lappa plant. The high-yield cultivation measures of Arctii Fructus are: around August 28 to sowing, planting density of 1 482 plants/667 m2, split application of fertilizer for four times, covering film on surface of the soil and topping in bolting.

Raising yield potential in wheat: increasing photosynthesis capacity and efficiency

USDA-ARS?s Scientific Manuscript database

Increasing wheat yields to help to ensure food security is a major challenge. Meeting this challenge requires a quantum improvement in the yield potential of wheat. Past increases in yield potential have largely resulted from improvements in harvest index not through increased biomass. Further large...

Multiple yielding processes in a colloidal gel under large amplitude oscillatory stress

NASA Astrophysics Data System (ADS)

Gibaud, Thomas; Perge, Christophe; Lindström, Stefan B.; Taberlet, Nicolas; Manneville, Sébastien

Fatigue refers to the changes in material properties caused by repeatedly applied loads. It has been widely studied for, e.g., construction materials, but much less has been done on soft materials. Here, we characterize the fatigue dynamics of a colloidal gel. Fatigue is induced by large amplitude oscillatory stress (LAOStress), and the local displacements of the gel are measured through high-frequency ultrasonic imaging. We show that fatigue eventually leads to rupture and fluidization. We evidence four successive steps associated with these dynamics: (i) the gel first remains solid, (ii) it then slides against the walls, (iii) the bulk of the sample becomes heterogeneous and displays solid-fluid coexistence, and (iv) it is finally fully fluidized. It is possible to homogeneously scale the duration of each step with respect to the stress oscillation amplitude $\\sigma_0$. The data are compatible with both exponential and power-law scalings with $\\sigma_0$, which hints at two possible interpretations in terms of delayed yielding in terms activated processes or of the Basquin law. Surprisingly, we find that the model parameters behave nonmonotonically as we change the oscillation frequency and/or the gel concentration.

Low Yield of Chest Radiography in a Large Tuberculosis Screening Program1

PubMed Central

Pollock, Nira R.

2010-01-01

Purpose: To assess the frequency and spectrum of abnormalities on routine screening chest radiographs in the pre-employment evaluation of health care workers with positive tuberculin skin test (TST) results. Materials and Methods: The institutional review board approved this HIPAA-compliant retrospective study and waived the need for written informed patient consent. Chest radiographic reports of all 2586 asymptomatic individuals with positive TST results who underwent pre-employment evaluation between January 1, 2003, and December 31, 2007, were evaluated to determine the frequency of detection of evidence of active tuberculosis (TB) or latent TB infection (LTBI) and the spectrum of imaging findings. All chest radiographs interpreted as positive were reviewed by an experienced board-certified radiologist. If there was a discrepancy between the two readings, a second experienced radiologist served as an independent and final arbiter. Any follow-up chest radiographs or computed tomographic images that had been acquired by employee health services or by the employee’s private physician as a result of a suspected abnormality detected at initial screening were also evaluated. Results: Of the 159 (6.1%) chest radiographic examinations that yielded abnormal results, there were no findings that were consistent with active TB. There were 92 cases of calcified granulomas, calcified lymph nodes, or both; 25 cases of apical pleural thickening; 16 cases of fibrous scarring; and 31 cases of noncalcified nodules. All cases of fibrous scarring involved an area smaller than 2 cm2. All noncalcified nodules were 4 mm in diameter or smaller, with the exception of one primary lung malignancy and one necrotizing granuloma (negative for acid-fast bacilli) that grew Mycobacterium kansasii on culture. Conclusion: Universal chest radiography in a large pre-employment TB screening program was of low yield in the detection of active TB or increased LTBI reactivation risk, and it provided

Chimpanzees Sometimes See Fuller as Better: Judgments of Food Quantities Based on Container Size and Fullness

PubMed Central

Parrish, Audrey E.; Beran, Michael J.

2014-01-01

The context in which food is presented can alter quantity judgments leading to sub-optimal choice behavior. Humans often over-estimate food quantity on the basis of how food is presented. Food appears larger if plated on smaller dishes than larger dishes and liquid volumes appear larger in taller cups than shorter cups. Moreover, smaller but fuller containers are preferred in comparison to larger, but less full containers with a truly larger quantity. Here, we assessed whether similar phenomena occur in chimpanzees. Four chimpanzees chose between two amounts of food presented in different sized containers, a large (2 oz.) and small (1 oz.) cup. When different quantities were presented in the same-sized cups or when the small cup contained the larger quantity, chimpanzees were highly accurate in choosing the larger food amount. However, when different-sized cups contained the same amount of food or the smaller cup contained the smaller amount of food (but looked relatively fuller), the chimpanzees often showed a bias to select the smaller but fuller cup. These findings contribute to our understanding of how quantity estimation and portion judgment is impacted by the surrounding context in which it is presented. PMID:24374384

PCP METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan, S.

The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials, are significantly less hazardous than large amounts of the same materials. This study describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials perform, under both normal and accident conditions, the essential functions of material containment, subcriticality, and maintain external radiation levels within regulatory limits.more » 10 CFR 71.33(b)(1)(2)&(3) state radioactive and fissile materials must be identified and their maximum quantity, chemical and physical forms be included in an application. Furthermore, the U.S. Federal Regulations require application contain an evaluation demonstrating the package (i.e., the packaging and its contents) satisfies the external radiation standards for all packages (10 CFR 71.31(2), 71.35(a), & 71.47). By placing the contents in a He leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large external dose rate. Quantifying of the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings described in this report provides bounding mass limits for a set of proposed SGQ isotopes. Methodology calculations were performed to estimate external

Identifying seedling root architectural traits associated with yield and yield components in wheat.

PubMed

Xie, Quan; Fernando, Kurukulasuriya M C; Mayes, Sean; Sparkes, Debbie L

2017-05-01

Plant roots growing underground are critical for soil resource acquisition, anchorage and plant-environment interactions. In wheat ( Triticum aestivum ), however, the target root traits to improve yield potential still remain largely unknown. This study aimed to identify traits of seedling root system architecture (RSA) associated with yield and yield components in 226 recombinant inbred lines (RILs) derived from a cross between the bread wheat Triticum aestivum 'Forno' (small, wide root system) and spelt Triticum spelta 'Oberkulmer' (large, narrow root system). A 'pouch and wick' high-throughput phenotyping pipeline was used to determine the RSA traits of 13-day-old RIL seedlings. Two field experiments and one glasshouse experiment were carried out to investigate the yield, yield components and phenology, followed by identification of quantitative trait loci (QTLs). There was substantial variation in RSA traits between genotypes. Seminal root number and total root length were both positively associated with grains m -2 , grains per spike, above-ground biomass m -2 and grain yield. More seminal roots and longer total root length were also associated with delayed maturity and extended grain filling, likely to be a consequence of more grains being defined before anthesis. Additionally, the maximum width of the root system displayed positive relationships with spikes m -2 , grains m -2 and grain yield. Ten RILs selected for the longest total roots exhibited the same effects on yield and phenology as described above, compared with the ten lines with the shortest total roots. Genetic analysis revealed 38 QTLs for the RSA, and QTL coincidence between the root and yield traits was frequently observed, indicating tightly linked genes or pleiotropy, which concurs with the results of phenotypic correlation analysis. Based on the results from the Forno × Oberkulmer population, it is proposed that vigorous early root growth, particularly more seminal roots and longer total

36 CFR 223.220 - Quantity determination.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

Fe(0) Nanomotors in Ton Quantities (10(20) Units) for Environmental Remediation.

PubMed

Teo, Wei Zhe; Zboril, Radek; Medrik, Ivo; Pumera, Martin

2016-03-24

Despite demonstrating potential for environmental remediation and biomedical applications, the practical environmental applications of autonomous self-propelled micro-/nanorobots have been limited by the inability to fabricate these devices in large (kilograms/tons) quantities. In view of the demand for large-scale environmental remediation by micro-/nanomotors, which are easily synthesized and powered by nontoxic fuel, we have developed bubble-propelled Fe(0) Janus nanomotors by a facile thermally induced solid-state procedure and investigated their potential as decontamination agents of pollutants. These Fe(0) Janus nanomotors, stabilized by an ultrathin iron oxide shell, were fuelled by their decomposition in citric acid, leading to the asymmetric bubble propulsion. The degradation of azo-dyes was dramatically increased in the presence of moving self-propelled Fe(0) nanomotors, which acted as reducing agents. Such enhanced pollutant decomposition triggered by biocompatible Fe(0) (nanoscale zero-valent iron motors), which can be handled in the air and fabricated in ton quantities for low cost, will revolutionize the way that environmental remediation is carried out. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Modeling of yield surface evolution in uniaxial and biaxial loading conditions using a prestrained large scale specimen

NASA Astrophysics Data System (ADS)

Zaman, Shakil Bin; Barlat, Frédéric; Kim, Jin Hwan

2018-05-01

Large-scale advanced high strength steel (AHSS) sheet specimens were deformed in uniaxial tension, using a novel grip system mounted on a MTS universal tension machine. After pre-strain, they were used as a pre-strained material to examine the anisotropic response in the biaxial tension tests with various load ratios, and orthogonal tension tests at 45° and 90° from the pre-strain axis. The flow curve and the instantaneous r-value of the pre-strained steel in each of the aforementioned uniaxial testing conditions were also measured and compared with those of the undeformed steel. Furthermore, an exhaustive analysis of the yield surface was also conducted and the results, prior and post-prestrain were represented and compared. The homogeneous anisotropic hardening (HAH) model [1] was employed to predict the behavior of the pre-strained material. It was found that the HAH-predicted flow curves after non-linear strain path change and the yield loci after uniaxial pre-strain were in good agreement with the experiments, while the r-value evolution after strain path change was qualitatively well predicted.

Large scale isolation and purification of soluble RAGE from lung tissue.

PubMed

Englert, Judson M; Ramsgaard, Lasse; Valnickova, Zuzana; Enghild, Jan J; Oury, Tim D

2008-09-01

The receptor for advanced glycation end-products (RAGE) has been implicated in numerous disease processes including: atherosclerosis, diabetic nephropathy, impaired wound healing and neuropathy to name a few. Treatment of animals with a soluble isoform of the receptor (sRAGE) has been shown to prevent and even reverse many disease processes. Isolating large quantities of pure sRAGE for in vitro and in vivo studies has hindered its development as a therapeutic strategy in other RAGE mediated diseases that require long-term therapy. This article provides an improvement in both yield and detail of a previously published method to obtain 10mg of pure, endotoxin free sRAGE from 65 g of lung tissue.

How the great apes (Pan troglodytes, Pongo pygmaeus, Pan paniscus, Gorilla gorilla) perform on the reversed reward contingency task II: transfer to new quantities, long-term retention, and the impact of quantity ratios.

PubMed

Uher, Jana; Call, Josep

2008-05-01

We tested 6 chimpanzees (Pan troglodytes), 3 orangutans (Pongo pygmaeus), 4 bonobos (Pan paniscus), and 2 gorillas (Gorilla gorilla) in the reversed reward contingency task. Individuals were presented with pairs of quantities ranging between 0 and 6 food items. Prior to testing, some experienced apes had solved this task using 2 quantities while others were totally naïve. Experienced apes transferred their ability to multiple-novel pairs after 6 to 19 months had elapsed since their initial testing. Two out of 6 naïve apes (1 chimpanzee, 1 bonobo) solved the task--a proportion comparable to that of a previous study using 2 pairs of quantities. Their acquisition speed was also comparable to the successful subjects from that study. The ratio between quantities explained a large portion of the variance but affected naïve and experienced individuals differently. For smaller ratios, naïve individuals were well below 50% correct and experienced ones were well above 50%, yet both groups tended to converge toward 50% for larger ratios. Thus, some apes require no procedural modifications to overcome their strong bias for selecting the larger of 2 quantities. PsycINFO Database Record (c) 2008 APA, all rights reserved.

Optimized Gen-II FeCrAl cladding production in large quantity for campaign testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, Yukinori; Sun, Zhiqian; Pint, Bruce A.

2016-06-03

There are two major objectives in this report; (1) to optimize microstructure control of ATF FeCrAl alloys during tube drawing processes, and (2) to provide an update on the progress of ATF FeCrAl tube production via commercial manufacturers. Experimental efforts have been made to optimize the process parameters balancing the tube fabricability, especially for tube drawing processes, and microstructure control of the final tube products. Lab-scale sheet materials of Gen II FeCrAl alloys (Mo-containing and Nb-containing FeCrAl alloys) were used in the study, combined with a stepwise warm-rolling process and intermediate annealing, aiming to simulate the tube drawing process inmore » a commercial tube manufacturer. The intermediate annealing at 650ºC for 1h was suggested for the tube-drawing process of Mo-containing FeCrAl alloys because it successfully softened the material by recovering the work hardening introduced through the rolling step, without inducing grain coarsening due to recrystallization. The final tube product is expected to have stabilized deformed microstructure providing the improved tensile properties with sufficient ductility. Optimization efforts on Nb-containing FeCrAl alloys focused on the effect of alloying additions and annealing conditions on the stability of deformed microstructure. Relationships between the second-phase precipitates (Fe 2Nb-Laves phase) and microstructure stability are discussed. FeCrAl tube production through commercial tube manufacturers is currently in progress. Three different manufacturers, Century Tubes, Inc. (CTI), Rhenium Alloys, Inc. (RAI), and Superior Tube Company, Inc. (STC), are providing capabilities for cold-drawing, warm-drawing, and HPTR cold-pilgering, respectively. The first two companies are currently working on large quantity tube production (expected 250 ft length) of Gen I model FeCrAl alloy (B136Y3, at CTI) and Gen II (C35M4, at RAI), with the process parameters obtained from the experimental

Large-scale production and study of a synthetic G protein-coupled receptor: Human olfactory receptor 17-4

PubMed Central

Cook, Brian L.; Steuerwald, Dirk; Kaiser, Liselotte; Graveland-Bikker, Johanna; Vanberghem, Melanie; Berke, Allison P.; Herlihy, Kara; Pick, Horst; Vogel, Horst; Zhang, Shuguang

2009-01-01

Although understanding of the olfactory system has progressed at the level of downstream receptor signaling and the wiring of olfactory neurons, the system remains poorly understood at the molecular level of the receptors and their interaction with and recognition of odorant ligands. The structure and functional mechanisms of these receptors still remain a tantalizing enigma, because numerous previous attempts at the large-scale production of functional olfactory receptors (ORs) have not been successful to date. To investigate the elusive biochemistry and molecular mechanisms of olfaction, we have developed a mammalian expression system for the large-scale production and purification of a functional OR protein in milligram quantities. Here, we report the study of human OR17-4 (hOR17-4) purified from a HEK293S tetracycline-inducible system. Scale-up of production yield was achieved through suspension culture in a bioreactor, which enabled the preparation of >10 mg of monomeric hOR17-4 receptor after immunoaffinity and size exclusion chromatography, with expression yields reaching 3 mg/L of culture medium. Several key post-translational modifications were identified using MS, and CD spectroscopy showed the receptor to be ≈50% α-helix, similar to other recently determined G protein-coupled receptor structures. Detergent-solubilized hOR17-4 specifically bound its known activating odorants lilial and floralozone in vitro, as measured by surface plasmon resonance. The hOR17-4 also recognized specific odorants in heterologous cells as determined by calcium ion mobilization. Our system is feasible for the production of large quantities of OR necessary for structural and functional analyses and research into OR biosensor devices. PMID:19581598

Large-scale production and study of a synthetic G protein-coupled receptor: human olfactory receptor 17-4.

PubMed

Cook, Brian L; Steuerwald, Dirk; Kaiser, Liselotte; Graveland-Bikker, Johanna; Vanberghem, Melanie; Berke, Allison P; Herlihy, Kara; Pick, Horst; Vogel, Horst; Zhang, Shuguang

2009-07-21

Although understanding of the olfactory system has progressed at the level of downstream receptor signaling and the wiring of olfactory neurons, the system remains poorly understood at the molecular level of the receptors and their interaction with and recognition of odorant ligands. The structure and functional mechanisms of these receptors still remain a tantalizing enigma, because numerous previous attempts at the large-scale production of functional olfactory receptors (ORs) have not been successful to date. To investigate the elusive biochemistry and molecular mechanisms of olfaction, we have developed a mammalian expression system for the large-scale production and purification of a functional OR protein in milligram quantities. Here, we report the study of human OR17-4 (hOR17-4) purified from a HEK293S tetracycline-inducible system. Scale-up of production yield was achieved through suspension culture in a bioreactor, which enabled the preparation of >10 mg of monomeric hOR17-4 receptor after immunoaffinity and size exclusion chromatography, with expression yields reaching 3 mg/L of culture medium. Several key post-translational modifications were identified using MS, and CD spectroscopy showed the receptor to be approximately 50% alpha-helix, similar to other recently determined G protein-coupled receptor structures. Detergent-solubilized hOR17-4 specifically bound its known activating odorants lilial and floralozone in vitro, as measured by surface plasmon resonance. The hOR17-4 also recognized specific odorants in heterologous cells as determined by calcium ion mobilization. Our system is feasible for the production of large quantities of OR necessary for structural and functional analyses and research into OR biosensor devices.

Yielding and flow of colloidal glasses.

PubMed

Petekidis, Georgios; Vlassopoulos, Dimitris; Pusey, Peter N

2003-01-01

We investigate the yielding and flow of hard-sphere colloidal glasses by combining rheological measurements with the technique of light scattering echo. The polymethylmethacrylate particles used are sufficiently polydisperse that crystallization is suppressed. Creep and recovery measurements show that the glasses can tolerate surprisingly large strains, up to at least 15%, before yielding irreversibly. We attribute this behaviour to 'cage elasticity', the ability of a particle and its cage of neighbours to retain their identity under quite large distortion. Results from light scattering echo, which measures the extent of irreversible particle rearrangement under oscillatory shear, support the notion of cage elasticity. In the lower concentration glasses we find that particle trajectories are partly reversible under strains which significantly exceed the yield strain.

Conceptual Model of Quantities, Units, Dimensions, and Values

NASA Technical Reports Server (NTRS)

Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

2011-01-01

JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

DNA quality and quantity from up to 16 years old post-mortem blood stored on FTA cards.

PubMed

Rahikainen, Anna-Liina; Palo, Jukka U; de Leeuw, Wiljo; Budowle, Bruce; Sajantila, Antti

2016-04-01

Blood samples preserved on FTA cards offer unique opportunities for genetic research. DNA recovered from these cards should be stable for long periods of time. However, it is not well established as how well the DNA stored on FTA card for substantial time periods meets the demands of forensic or genomic DNA analyses and especially so for from post-mortem (PM) samples in which the quality can vary upon initial collection. The aim of this study was to evaluate the time-dependent degradation on DNA quality and quantity extracted from up to 16 years old post-mortem bloodstained FTA cards. Four random FTA samples from eight time points spanning 1998 to 2013 (n=32) were collected and extracted in triplicate. The quantity and quality of the extracted DNA samples were determined with Quantifiler(®) Human Plus (HP) Quantification kit. Internal sample and sample-to-sample variation were evaluated by comparing recovered DNA yields. The DNA from the triplicate samplings were subsequently combined and normalized for further analysis. The practical effect of degradation on DNA quality was evaluated from normalized samples both with forensic and pharmacogenetic target markers. Our results suggest that (1) a PM change, e.g. blood clotting prior to sampling, affects the recovered DNA yield, creating both internal and sample-to-sample variation; (2) a negative correlation between the FTA card storage time and DNA quantity (r=-0.836 at the 0.01 level) was observed; (3) a positive correlation (r=0.738 at the level 0.01) was found between FTA card storage time and degradation levels. However, no inhibition was observed with the method used. The effect of degradation was manifested clearly with functional applications. Although complete STR-profiles were obtained for all samples, there was evidence of degradation manifested as decreased peak heights in the larger-sized amplicons. Lower amplification success was notable with the large 5.1 kb CYP2D6 gene fragment which strongly supports

Quantifying cannabis: A field study of marijuana quantity estimation.

PubMed

Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

2018-06-01

The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Judgement of discrete and continuous quantity in adults: number counts!

PubMed

Nys, Julie; Content, Alain

2012-01-01

Three experiments involving a Stroop-like paradigm were conducted. In Experiment 1, adults received a number comparison task in which large sets of dots, orthogonally varying along a discrete dimension (number of dots) and a continuous dimension (cumulative area), were presented. Incongruent trials were processed more slowly and with less accuracy than congruent trials, suggesting that continuous dimensions such as cumulative area are automatically processed and integrated during a discrete quantity judgement task. Experiment 2, in which adults were asked to perform area comparison on the same stimuli, revealed the reciprocal interference from number on the continuous quantity judgements. Experiment 3, in which participants received both the number and area comparison tasks, confirmed the results of Experiments 1 and 2. Contrasting with earlier statements, the results support the view that number acts as a more salient cue than continuous dimensions in adults. Furthermore, the individual predisposition to automatically access approximate number representations was found to correlate significantly with adults' exact arithmetical skills.

Units for quantities of dimension one

NASA Astrophysics Data System (ADS)

Dybkaer, René

2004-02-01

All quantities of dimension one are said to have the SI coherent derived unit "one" with the symbol '1'. (Single quotation marks are used here sometimes to indicate a quote, name, term or symbol; double quotation marks flag a concept when necessary.) Conventionally, the term and symbol may not be combined with the SI prefixes (except for the special terms and symbols for one and 1: radian, rad, and steradian, sr). This restriction is understandable, but leads to correct yet impractical alternatives and ISO deprecated symbols such as ppm or in some cases redundant combinations of units, such as mg/kg. "Number of entities" is dimensionally independent of the current base quantities and should take its rightful place among them. The corresponding base unit is "one". A working definition is given. Other quantities of dimension one are derived as fraction, ratio, efficiency, relative quantity, relative increment or characteristic number and may also use the unit "one", whether considered to be base or derived. The special term 'uno' and symbol 'u' in either case are proposed, allowing combination with SI prefixes.

49 CFR 172.315 - Limited quantities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... accordance with the white square-on-point limited quantity marking as follows: (1) The limited quantity... forming the square-on-point must be at least 2 mm and the minimum dimension of each side must be 100 mm... top and bottom portions of the square-on-point and the border forming the square-on-point must be...

CDOM Sources and Photobleaching Control Quantum Yields for Oceanic DMS Photolysis.

PubMed

Galí, Martí; Kieber, David J; Romera-Castillo, Cristina; Kinsey, Joanna D; Devred, Emmanuel; Pérez, Gonzalo L; Westby, George R; Marrasé, Cèlia; Babin, Marcel; Levasseur, Maurice; Duarte, Carlos M; Agustí, Susana; Simó, Rafel

2016-12-20

Photolysis is a major removal pathway for the biogenic gas dimethylsulfide (DMS) in the surface ocean. Here we tested the hypothesis that apparent quantum yields (AQY) for DMS photolysis varied according to the quantity and quality of its photosensitizers, chiefly chromophoric dissolved organic matter (CDOM) and nitrate. AQY compiled from the literature and unpublished studies ranged across 3 orders of magnitude at the 330 nm reference wavelength. The smallest AQY(330) were observed in coastal waters receiving major riverine inputs of terrestrial CDOM (0.06-0.5 m 3 (mol quanta) -1 ). In open-ocean waters, AQY(330) generally ranged between 1 and 10 m 3 (mol quanta) -1 . The largest AQY(330), up to 34 m 3 (mol quanta) -1 ), were seen in the Southern Ocean potentially associated with upwelling. Despite the large AQY variability, daily photolysis rate constants at the sea surface spanned a smaller range (0.04-3.7 d -1 ), mainly because of the inverse relationship between CDOM absorption and AQY. Comparison of AQY(330) with CDOM spectral signatures suggests there is an interplay between CDOM origin (terrestrial versus marine) and photobleaching that controls variations in AQYs, with a secondary role for nitrate. Our results can be used for regional or large-scale assessment of DMS photolysis rates in future studies.

Effects of plant density on recombinant hemagglutinin yields in an Agrobacterium-mediated transient gene expression system using Nicotiana benthamiana plants.

PubMed

Fujiuchi, Naomichi; Matsuda, Ryo; Matoba, Nobuyuki; Fujiwara, Kazuhiro

2017-08-01

Agrobacterium-mediated transient expression systems enable plants to rapidly produce a wide range of recombinant proteins. To achieve economically feasible upstream production and downstream processing, it is beneficial to obtain high levels of two yield-related quantities of upstream production: recombinant protein content per fresh mass of harvested biomass (g gFM -1 ) and recombinant protein productivity per unit area-time (g m -2 /month). Here, we report that the density of Nicotiana benthamiana plants during upstream production had significant impacts on the yield-related quantities of recombinant hemagglutinin (HA). The two quantities were smaller at a high plant density of 400 plants m -2 than at a low plant density of 100 plants m -2 . The smaller quantities at the high plant density were attributed to: (i) a lower HA content in young leaves, which usually have high HA accumulation potentials; (ii) a lower biomass allocation to the young leaves; and (iii) a high area-time requirement for plants. Thus, plant density is a key factor for improving upstream production in Agrobacterium-mediated transient expression systems. Biotechnol. Bioeng. 2017;114: 1762-1770. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

The Acquisition of Quantity Contrasts in Guina-ang Bontok

ERIC Educational Resources Information Center

Aoyama, Katsura; Reid, Lawrence A.

2016-01-01

This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

Crop status evaluations and yield predictions

NASA Technical Reports Server (NTRS)

Haun, J. R.

1976-01-01

One phase of the large area crop inventory project is presented. Wheat yield models based on the input of environmental variables potentially obtainable through the use of space remote sensing were developed and demonstrated. By the use of a unique method for visually qualifying daily plant development and subsequent multifactor computer analyses, it was possible to develop practical models for predicting crop development and yield. Development of wheat yield prediction models was based on the discovery that morphological changes in plants are detected and quantified on a daily basis, and that this change during a portion of the season was proportional to yield.

Quantity and quality benefits of in-service invasive cleaning of trunk mains

NASA Astrophysics Data System (ADS)

Sunny, Iftekhar; Husband, Stewart; Drake, Nick; Mckenzie, Kevan; Boxall, Joby

2017-07-01

Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity) and quality (e.g. discolouration) of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

An Algebraic Approach to Unital Quantities and their Measurement

NASA Astrophysics Data System (ADS)

Domotor, Zoltan; Batitsky, Vadim

2016-06-01

The goals of this paper fall into two closely related areas. First, we develop a formal framework for deterministic unital quantities in which measurement unitization is understood to be a built-in feature of quantities rather than a mere annotation of their numerical values with convenient units. We introduce this idea within the setting of certain ordered semigroups of physical-geometric states of classical physical systems. States are assumed to serve as truth makers of metrological statements about quantity values. A unital quantity is presented as an isomorphism from the target system's ordered semigroup of states to that of positive reals. This framework allows us to include various derived and variable quantities, encountered in engineering and the natural sciences. For illustration and ease of presentation, we use the classical notions of length, time, electric current and mean velocity as primordial examples. The most important application of the resulting unital quantity calculus is in dimensional analysis. Second, in evaluating measurement uncertainty due to the analog-to-digital conversion of the measured quantity's value into its measuring instrument's pointer quantity value, we employ an ordered semigroup framework of pointer states. Pointer states encode the measuring instrument's indiscernibility relation, manifested by not being able to distinguish the measured system's topologically proximal states. Once again, we focus mainly on the measurement of length and electric current quantities as our motivating examples. Our approach to quantities and their measurement is strictly state-based and algebraic in flavor, rather than that of a representationalist-style structure-preserving numerical assignment.

Controlled-rate freezer cryopreservation of highly concentrated peripheral blood mononuclear cells results in higher cell yields and superior autologous T-cell stimulation for dendritic cell-based immunotherapy.

PubMed

Buhl, Timo; Legler, Tobias J; Rosenberger, Albert; Schardt, Anke; Schön, Michael P; Haenssle, Holger A

2012-11-01

Availability of large quantities of functionally effective dendritic cells (DC) represents one of the major challenges for immunotherapeutic trials against infectious or malignant diseases. Low numbers or insufficient T-cell activation of DC may result in premature termination of treatment and unsatisfying immune responses in clinical trials. Based on the notion that cryopreservation of monocytes is superior to cryopreservation of immature or mature DC in terms of resulting DC quantity and immuno-stimulatory capacity, we aimed to establish an optimized protocol for the cryopreservation of highly concentrated peripheral blood mononuclear cells (PBMC) for DC-based immunotherapy. Cryopreserved cell preparations were analyzed regarding quantitative recovery, viability, phenotype, and functional properties. In contrast to standard isopropyl alcohol (IPA) freezing, PBMC cryopreservation in an automated controlled-rate freezer (CRF) with subsequent thawing and differentiation resulted in significantly higher cell yields of immature and mature DC. Immature DC yields and total protein content after using CRF were comparable with results obtained with freshly prepared PBMC and exceeded results of standard IPA freezing by approximately 50 %. While differentiation markers, allogeneic T-cell stimulation, viability, and cytokine profiles were similar to DC from standard freezing procedures, DC generated from CRF-cryopreserved PBMC induced a significantly higher antigen-specific IFN-γ release from autologous effector T cells. In summary, automated controlled-rate freezing of highly concentrated PBMC represents an improved method for increasing DC yields and autologous T-cell stimulation.

Large Area Crop Inventory Experiment (LACIE). Feasibility of assessing crop condition and yield from LANDSAT data

NASA Technical Reports Server (NTRS)

1978-01-01

The author has identified the following significant results. Yield modelling for crop production estimation derived a means of predicting the within-a-year yield and the year-to-year variability of yield over some fixed or randomly located unit of area. Preliminary studies indicated that the requirements for interpreting LANDSAT data for yield may be sufficiently similar to those of signature extension that it is feasible to investigate the automated estimation of production. The concept of an advanced yield model consisting of both spectral and meteorological components was endorsed. Rationale for using meteorological parameters originated from known between season and near harvest dynamics in crop environmental-condition-yield relationships.

INTERNATIONAL REPORTS: New International Standards for Quantities and Units

NASA Astrophysics Data System (ADS)

Thor, A. J.

1994-01-01

Each coherent system of units is based on a system of quantities in such a way that the equations between the numerical values expressed in coherent units have exactly the same form, including numerical factors, as the corresponding equations between the quantities. The highest international body responsible for the International System of Units (SI) is the Conférence Générale des Poids et Mesures (CGPM). However, the CGPM is not concerned with quantities or systems of quantities. That question lies within the scope of Technical Committee number twelve of the International Organization for Standardization (ISO/TC 12). Quantities, units, symbols, conversion factors. To fulfil its responsibility, ISO/TC 12 has prepared the International Standard ISO 31, Quantities and Units, which consists of fourteen parts. The new editions of the different parts of the International Standard are briefly presented here.

48 CFR 816.504 - Indefinite-quantity contracts.

Code of Federal Regulations, 2011 CFR

2011-10-01

... issue a solicitation for estimated quantities, the contracting officer shall insert the clause at 852.216-70, Estimated quantities. (b) The contracting officer shall insert the Alternate I clause at 852.216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

Hypergraph topological quantities for tagged social networks.

PubMed

Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

2009-09-01

Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

Hypergraph topological quantities for tagged social networks

NASA Astrophysics Data System (ADS)

Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

2009-09-01

Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

Relative quantity judgments in South American sea lions (Otaria flavescens).

PubMed

Abramson, José Z; Hernández-Lloreda, Victoria; Call, Josep; Colmenares, Fernando

2011-09-01

There is accumulating evidence that a variety of species possess quantitative abilities although their cognitive substrate is still unclear. This study is the first to investigate whether sea lions (Otaria flavescens), in the absence of training, are able to assess and select the larger of two sets of quantities. In Experiment 1, the two sets of quantities were presented simultaneously as whole sets, that is, the subjects could compare them directly. In Experiment 2, the two sets of quantities were presented item-by-item, and the totality of items was never visually available at the time of choice. For each type of presentation, we analysed the effect of the ratio between quantities, the difference between quantities and the total number of items presented. The results showed that (1) sea lions can make relative quantity judgments successfully and (2) there is a predominant influence of the ratio between quantities on the subjects' performance. The latter supports the idea that an analogue representational mechanism is responsible for sea lions' relative quantities judgments. These findings are consistent with previous reports of relative quantities judgments in other species such as monkeys and apes and suggest that sea lions might share a similar mechanism to compare and represent quantities.

14 CFR 25.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel quantity indicator. 25.1553 Section 25.1553 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or...

14 CFR 23.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Fuel quantity indicator. 23.1553 Section 23.1553 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each...

Variation of organic matter quantity and quality in streams at Critical Zone Observatory watersheds

Treesearch

Matthew P. Miller; Elizabeth W. Boyer; Diane M. McKnight; Michael G. Brown; Rachel S. Gabor; Carolyn Hunsaker; Lidiia Iavorivska; Shreeram Inamdar; Dale W. Johnson; Louis A. Kaplan; Henry Lin; William H. McDowell; Julia N. Perdrial

2016-01-01

The quantity and chemical composition of dissolved organic matter (DOM) in surface waters influence ecosystem processes and anthropogenic use of freshwater. However, despite the importance of understanding spatial and temporal patterns in DOM, measures of DOM quality are not routinely included as part of large-scale ecosystem monitoring programs and variations in...

Effects of Source RDP Models and Near-source Propagation: Implication for Seismic Yield Estimation

NASA Astrophysics Data System (ADS)

Saikia, C. K.; Helmberger, D. V.; Stead, R. J.; Woods, B. B.

- It has proven difficult to uniquely untangle the source and propagation effects on the observed seismic data from underground nuclear explosions, even when large quantities of near-source, broadband data are available for analysis. This leads to uncertainties in our ability to quantify the nuclear seismic source function and, consequently the accuracy of seismic yield estimates for underground explosions. Extensive deterministic modeling analyses of the seismic data recorded from underground explosions at a variety of test sites have been conducted over the years and the results of these studies suggest that variations in the seismic source characteristics between test sites may be contributing to the observed differences in the magnitude/yield relations applicable at those sites. This contributes to our uncertainty in the determination of seismic yield estimates for explosions at previously uncalibrated test sites. In this paper we review issues involving the relationship of Nevada Test Site (NTS) source scaling laws to those at other sites. The Joint Verification Experiment (JVE) indicates that a magnitude (mb) bias (δmb) exists between the Semipalatinsk test site (STS) in the former Soviet Union (FSU) and the Nevada test site (NTS) in the United States. Generally this δmb is attributed to differential attenuation in the upper-mantle beneath the two test sites. This assumption results in rather large estimates of yield for large mb tunnel shots at Novaya Zemlya. A re-examination of the US testing experiments suggests that this δmb bias can partly be explained by anomalous NTS (Pahute) source characteristics. This interpretation is based on the modeling of US events at a number of test sites. Using a modified Haskell source description, we investigated the influence of the source Reduced Displacement Potential (RDP) parameters ψ ∞ , K and B by fitting short- and long-period data simultaneously, including the near-field body and surface waves. In general

49 CFR 173.4a - Excepted quantities.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ice), and lithium batteries and cells. (c) Inner packaging limits. The maximum quantity of hazardous materials in each inner packaging is limited to: (1) For toxic material with a Division 6.1 primary or... excepted quantities must meet the following: (1) Each inner receptacle must be constructed of plastic, or...

10 CFR 26.109 - Urine specimen quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine specimen quantity. (a) Licensees and other entities who are subject to this subpart shall establish a...

10 CFR 26.109 - Urine specimen quantity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine specimen quantity. (a) Licensees and other entities who are subject to this subpart shall establish a...

Drought effects on composition and yield for corn stover, mixed grasses, and Miscanthus as bioenergy feedstocks

USDA-ARS?s Scientific Manuscript database

Drought conditions in 2012 were some of the most severe in recent history. The purpose of this study was to examine the impact of drought on quality, quantity, and theoretical ethanol yield (TEY) of three bioenergy feedstocks, corn stover, mixed perennial grasses from Conservation Reserve Program de...

41 CFR 101-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

41 CFR 101-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 2 2011-07-01 2007-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

41 CFR 101-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 41 Public Contracts and Property Management 2 2012-07-01 2012-07-01 false Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

41 CFR 101-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 2 2013-07-01 2012-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

41 CFR 101-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 2 2014-07-01 2012-07-01 true Economic order quantity... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ...

Supply chain coordination with defective items and quantity discount

NASA Astrophysics Data System (ADS)

Lin, Hsien-Jen; Lin, Yu-Jen

2014-12-01

This study develops an integrated inventory system involving defective items and quantity discount for optimal pricing and ordering strategies. The model analysed in this study is one in which the buyer orders a quantity, the vendor produces more than buyer's order quantity in order to reduce set-up cost, and then he/she offers an all-units quantity discount to the buyer. Our objective is to determine the optimal order quantity, retail price, mark-up rate, and the number of shipments per production run from the vendor to the buyer, so that the entire supply chain joint total profit incurred has a maximum value. Furthermore, an algorithm of finding the optimal solution is developed. Numerical examples are provided to illustrate the theoretical results.

7 CFR 1207.511 - Determination of assessable quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

7 CFR 1207.511 - Determination of assessable quantity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

7 CFR 1207.511 - Determination of assessable quantity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... POTATO RESEARCH AND PROMOTION PLAN Rules and Regulations Assessments § 1207.511 Determination of assessable quantity. The assessable quantity of potatoes in any lot shall be determined on the basis of...

Analysis of the trade-off between high crop yield and low yield instability at the global scale

NASA Astrophysics Data System (ADS)

Ben-Ari, Tamara; Makowski, David

2016-10-01

Yield dynamics of major crops species vary remarkably among continents. Worldwide distribution of cropland influences both the expected levels and the interannual variability of global yields. An expansion of cultivated land in the most productive areas could theoretically increase global production, but also increase global yield instability if the most productive regions are characterized by high interannual yield variability. In this letter, we use portfolio analysis to quantify the tradeoff between the expected values and the interannual variance of global yield. We compute optimal frontiers for four crop species i.e., maize, rice, soybean and wheat and show how the distribution of cropland among large world regions can be optimized to either increase expected global crop production or decrease its interannual variability. We also show that a preferential allocation of cropland in the most productive regions can increase global expected yield at the expense of yield stability. Theoretically, optimizing the distribution of a small fraction of total cultivated areas can help find a good compromise between low instability and high crop yields at the global scale.

Quantum Physics and Mathematical Debates Concerning the Problem of the Ontological Priority between Continuous Quantity and Discrete Quantity

NASA Astrophysics Data System (ADS)

Pin, Victor Gómez

In his book about the Categories (that is about the ultimate elements of classification and order), in the chapter concerning the quantity (IV, 20) Aristotle says that this concept recovers two kinds of modalities: the discrete quantity and the continuous quantity and he gives as examples the number for the first one; line, surface, solid, times and space for the second one. The main philosophical problem raised by this text is to determine which of the two modalities of the quantity has the ontological priority over the other (given two concepts A and B, we assume that A has ontological priority over B if every entity that possesses the quality B possesses necessarily the quality A). The problem is magnified by the fact that space, which in some part of Aristotle's Physics is mentioned not only as a category properly speaking but even as the main category whose power can be amazing, is in the evoked text of the Categories's Book reduced to expression of the continuum, and sharing this condition with time. In this matter the controversy is constant through the common history of Science and Philosophy.

Rethinking Intensive Quantities via Guided Mediated Abduction

ERIC Educational Resources Information Center

Abrahamson, Dor

2012-01-01

Some intensive quantities, such as slope, velocity, or likelihood, are perceptually privileged in the sense that they are experienced as holistic, irreducible sensations. However, the formal expression of these quantities uses "a/b" analytic metrics; for example, the slope of a line is the quotient of its rise and run. Thus, whereas students'…

7 CFR 1434.9 - Determination of quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS FOR HONEY § 1434.9 Determination of quantity. The amount of a marketing assistance loan and loan... the producer and verified by the county office representative for honey on Form CCC-633 (Honey) that is eligible to be pledged as security for the loan or LDP Estimates of the quantity of honey shall be...

7 CFR 1434.9 - Determination of quantity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... REGULATIONS FOR HONEY § 1434.9 Determination of quantity. The amount of a marketing assistance loan and loan... the producer and verified by the county office representative for honey on Form CCC-633 (Honey) that is eligible to be pledged as security for the loan or LDP Estimates of the quantity of honey shall be...

The Z {yields} cc-bar {yields} {gamma}{gamma}*, Z {yields} bb-bar {yields} {gamma}{gamma}* triangle diagrams and the Z {yields} {gamma}{psi}, Z {yields} {gamma}Y decays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Achasov, N. N., E-mail: achasov@math.nsc.ru

2011-03-15

The approach to the Z {yields} {gamma}{psi} and Z {yields} {gamma}Y decay study is presented in detail, based on the sum rules for the Z {yields} cc-bar {yields} {gamma}{gamma}* and Z {yields} bb-bar {yields} {gamma}{gamma}* amplitudes and their derivatives. The branching ratios of the Z {yields} {gamma}{psi} and Z {yields} {gamma}Y decays are calculated for different hypotheses on saturation of the sum rules. The lower bounds of {Sigma}{sub {psi}} BR(Z {yields} {gamma}{psi}) = 1.95 Multiplication-Sign 10{sup -7} and {Sigma}{sub {upsilon}} BR(Z {yields} {gamma}Y) = 7.23 Multiplication-Sign 10{sup -7} are found. Deviations from the lower bounds are discussed, including the possibilitymore » of BR(Z {yields} {gamma}J/{psi}(1S)) {approx} BR(Z {yields} {gamma}Y(1S)) {approx} 10{sup -6}, that could be probably measured in LHC. The angular distributions in the Z {yields} {gamma}{psi} and Z {yields} {gamma}Y decays are also calculated.« less

Second Generation Crop Yield Models Review

NASA Technical Reports Server (NTRS)

Hodges, T. (Principal Investigator)

1982-01-01

Second generation yield models, including crop growth simulation models and plant process models, may be suitable for large area crop yield forecasting in the yield model development project. Subjective and objective criteria for model selection are defined and models which might be selected are reviewed. Models may be selected to provide submodels as input to other models; for further development and testing; or for immediate testing as forecasting tools. A plant process model may range in complexity from several dozen submodels simulating (1) energy, carbohydrates, and minerals; (2) change in biomass of various organs; and (3) initiation and development of plant organs, to a few submodels simulating key physiological processes. The most complex models cannot be used directly in large area forecasting but may provide submodels which can be simplified for inclusion into simpler plant process models. Both published and unpublished models which may be used for development or testing are reviewed. Several other models, currently under development, may become available at a later date.

ABSORBANCE, ABSORPTION COEFFICIENT, AND APPARENT QUANTUM YIELD: A COMMENT ON AMBIGUITY IN THE USE OF THESE OPTICAL CONCEPTS

EPA Science Inventory

Several important optical terms such as "absorbance" and "absorption coefficient" are frequently used ambiguously in the current peer-reviewed literature. Since they are important terms that are required to derive other quantities such as the "apparent quantum yield" of photoprod...

Yield strength of Cu and an engineered material of Cu with 1% Pb

NASA Astrophysics Data System (ADS)

Buttler, William; Gray, George, III; Fensin, Saryu; Grover, Mike; Stevens, Gerald; Stone, Joseph; Turley, William

2015-06-01

To study the effects of engineered elastic-plastic yield on the mass-ejection from shocked materials we fielded explosively driven Cu and CuPb experiments. The Cu and CuPb experiments fielded fully annealed disks in contact with PBX 9501; the CuPb was extruded with 1% Pb that aggregates at the Cu grain boundaries. The elastic-plastic yield strength is explored as a difference of ejecta production of CuPb versus Cu, where the ejecta production of solid materials ties directly to the surface perturbation geometries of wavelengths (fixed at 65 μm) and amplitudes (which were varied). We observed that the Cu performs as expected, with ejecta turning on at the previously observed yield threshold, but the CuPb ejects mass in much larger quantities, at much lower wavenumber (k = 2 π/ λ) amplitude (h) products (kh), implying a reduced elastic-plastic yield stress of the engineered material, CuPb.

Aerobic digestion reduces the quantity of antibiotic resistance genes in residual municipal wastewater solids

PubMed Central

Burch, Tucker R.; Sadowsky, Michael J.; LaPara, Timothy M.

2012-01-01

Numerous initiatives have been undertaken to circumvent the problem of antibiotic resistance, including the development of new antibiotics, the use of narrow spectrum antibiotics, and the reduction of inappropriate antibiotic use. We propose an alternative but complimentary approach to reduce antibiotic resistant bacteria (ARB) by implementing more stringent technologies for treating municipal wastewater, which is known to contain large quantities of ARB and antibiotic resistance genes (ARGs). In this study, we investigated the ability of conventional aerobic digestion to reduce the quantity of ARGs in untreated wastewater solids. A bench-scale aerobic digester was fed untreated wastewater solids collected from a full-scale municipal wastewater treatment facility. The reactor was operated under semi-continuous flow conditions for more than 200 days at a residence time of approximately 40 days. During this time, the quantities of tet(A), tet(W), and erm(B) decreased by more than 90%. In contrast, intI1 did not decrease, and tet(X) increased in quantity by 5-fold. Following operation in semi-continuous flow mode, the aerobic digester was converted to batch mode to determine the first-order decay coefficients, with half-lives ranging from as short as 2.8 days for tet(W) to as long as 6.3 days for intI1. These results demonstrated that aerobic digestion can be used to reduce the quantity of ARGs in untreated wastewater solids, but that rates can vary substantially depending on the reactor design (i.e., batch vs. continuous-flow) and the specific ARG. PMID:23407455

Aerobic digestion reduces the quantity of antibiotic resistance genes in residual municipal wastewater solids.

PubMed

Burch, Tucker R; Sadowsky, Michael J; Lapara, Timothy M

2013-01-01

Numerous initiatives have been undertaken to circumvent the problem of antibiotic resistance, including the development of new antibiotics, the use of narrow spectrum antibiotics, and the reduction of inappropriate antibiotic use. We propose an alternative but complimentary approach to reduce antibiotic resistant bacteria (ARB) by implementing more stringent technologies for treating municipal wastewater, which is known to contain large quantities of ARB and antibiotic resistance genes (ARGs). In this study, we investigated the ability of conventional aerobic digestion to reduce the quantity of ARGs in untreated wastewater solids. A bench-scale aerobic digester was fed untreated wastewater solids collected from a full-scale municipal wastewater treatment facility. The reactor was operated under semi-continuous flow conditions for more than 200 days at a residence time of approximately 40 days. During this time, the quantities of tet(A), tet(W), and erm(B) decreased by more than 90%. In contrast, intI1 did not decrease, and tet(X) increased in quantity by 5-fold. Following operation in semi-continuous flow mode, the aerobic digester was converted to batch mode to determine the first-order decay coefficients, with half-lives ranging from as short as 2.8 days for tet(W) to as long as 6.3 days for intI1. These results demonstrated that aerobic digestion can be used to reduce the quantity of ARGs in untreated wastewater solids, but that rates can vary substantially depending on the reactor design (i.e., batch vs. continuous-flow) and the specific ARG.

Quantity Competition in a Differentiated Duopoly

NASA Astrophysics Data System (ADS)

Ferreira, Fernanda A.; Ferreira, Flávio; Ferreira, Miguel; Pinto, Alberto A.

In this paper, we consider a Stackelberg duopoly competition with differentiated goods, linear and symmetric demand and with unknown costs. In our model, the two firms play a non-cooperative game with two stages: in a first stage, firm F 1 chooses the quantity, q 1, that is going to produce; in the second stage, firm F 2 observes the quantity q 1 produced by firm F 1 and chooses its own quantity q 2. Firms choose their output levels in order to maximise their profits. We suppose that each firm has two different technologies, and uses one of them following a certain probability distribution. The use of either one or the other technology affects the unitary production cost. We show that there is exactly one perfect Bayesian equilibrium for this game. We analyse the variations of the expected profits with the parameters of the model, namely with the parameters of the probability distributions, and with the parameters of the demand and differentiation.

14 CFR 25.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 25.1553 Section 25... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator...

14 CFR 27.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 27.1553 Section 27... § 27.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator extending...

14 CFR 23.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 23.1553 Section 23... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each indicator at the calibrated zero reading, as specified in § 23.1337(b)(1). [Doc. No. 27807, 61 FR 5193, Feb...

14 CFR 29.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Fuel quantity indicator. 29.1553 Section 29... Placards § 29.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator...

14 CFR 23.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel quantity indicator. 23.1553 Section 23... Information Markings and Placards § 23.1553 Fuel quantity indicator. A red radial line must be marked on each indicator at the calibrated zero reading, as specified in § 23.1337(b)(1). [Doc. No. 27807, 61 FR 5193, Feb...

14 CFR 27.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel quantity indicator. 27.1553 Section 27... § 27.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or five percent of the tank capacity, whichever is greater, a red arc must be marked on its indicator extending...

Repeatability for oleoresin yield determinations in southern pines

Treesearch

J. H. Roberds; Brian L. Strom

2004-01-01

Flow of constitutive oleoresin is believed to be a major component of tree defense against attack by the southern pine pine beetle (Dendroctonus frontalis Zimmermann). Pines that exude large quantities of oleoresin are considered to be most capable of preventing or obstructing colonization by this destructive insect herbivore (Hodges et al. 1979;...

Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

PubMed

Zhai, Shiyan; Song, Genxin; Qin, Yaochen; Ye, Xinyue; Lee, Jay

2017-01-01

This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach

PubMed Central

Qin, Yaochen; Lee, Jay

2017-01-01

This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention. PMID:28950027

Reportable Quantities Federal Register Notices

EPA Pesticide Factsheets

Comprehensive Environmental Response, Compensation and Liability Act regulation designates specific substances as hazardous; identifies the quantity of substances which, when released, requires notification; and sets forth the notification requirements.

Comparing organic farming and land sparing: optimizing yield and butterfly populations at a landscape scale.

PubMed

Hodgson, Jenny A; Kunin, William E; Thomas, Chris D; Benton, Tim G; Gabriel, Doreen

2010-11-01

Organic farming aims to be wildlife-friendly, but it may not benefit wildlife overall if much greater areas are needed to produce a given quantity of food. We measured the density and species richness of butterflies on organic farms, conventional farms and grassland nature reserves in 16 landscapes. Organic farms supported a higher density of butterflies than conventional farms, but a lower density than reserves. Using our data, we predict the optimal land-use strategy to maintain yield whilst maximizing butterfly abundance under different scenarios. Farming conventionally and sparing land as nature reserves is better for butterflies when the organic yield per hectare falls below 87% of conventional yield. However, if the spared land is simply extra field margins, organic farming is optimal whenever organic yields are over 35% of conventional yields. The optimal balance of land sparing and wildlife-friendly farming to maintain production and biodiversity will differ between landscapes. © 2010 Blackwell Publishing Ltd/CNRS.

48 CFR 14.212 - Economic purchase quantities (supplies).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

49 CFR 224.105 - Sheeting dimensions and quantity.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

49 CFR 224.105 - Sheeting dimensions and quantity.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

49 CFR 224.105 - Sheeting dimensions and quantity.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

49 CFR 224.105 - Sheeting dimensions and quantity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

49 CFR 224.105 - Sheeting dimensions and quantity.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Sheeting dimensions and quantity. 224.105 Section 224.105 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD..., Inspection, and Maintenance of Retroreflective Material § 224.105 Sheeting dimensions and quantity...

40 CFR 302.5 - Determination of reportable quantities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 28 2011-07-01 2011-07-01 false Determination of reportable quantities. 302.5 Section 302.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY PLANNING, AND COMMUNITY RIGHT-TO-KNOW PROGRAMS DESIGNATION, REPORTABLE QUANTITIES, AND...

48 CFR 14.212 - Economic purchase quantities (supplies).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

48 CFR 14.212 - Economic purchase quantities (supplies).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

48 CFR 14.212 - Economic purchase quantities (supplies).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

48 CFR 14.212 - Economic purchase quantities (supplies).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Economic purchase... REGULATION CONTRACTING METHODS AND CONTRACT TYPES SEALED BIDDING Solicitation of Bids 14.212 Economic purchase quantities (supplies). Contracting officers shall comply with the economic purchase quantity...

Using Geostatistical Data Fusion Techniques and MODIS Data to Upscale Simulated Wheat Yield

NASA Astrophysics Data System (ADS)

Castrignano, A.; Buttafuoco, G.; Matese, A.; Toscano, P.

2014-12-01

Population growth increases food request. Assessing food demand and predicting the actual supply for a given location are critical components of strategic food security planning at regional scale. Crop yield can be simulated using crop models because is site-specific and determined by weather, management, length of growing season and soil properties. Crop models require reliable location-specific data that are not generally available. Obtaining these data at a large number of locations is time-consuming, costly and sometimes simply not feasible. An upscaling method to extend coverage of sparse estimates of crop yield to an appropriate extrapolation domain is required. This work is aimed to investigate the applicability of a geostatistical data fusion approach for merging remote sensing data with the predictions of a simulation model of wheat growth and production using ground-based data. The study area is Capitanata plain (4000 km2) located in Apulia Region, mostly cropped with durum wheat. The MODIS EVI/NDVI data products for Capitanata plain were downloaded from the Land Processes Distributed Active Archive Center (LPDAAC) remote for the whole crop cycle of durum wheat. Phenological development, biomass growth and grain quantity of durum wheat were simulated by the Delphi system, based on a crop simulation model linked to a database including soil properties, agronomical and meteorological data. Multicollocated cokriging was used to integrate secondary exhaustive information (multi-spectral MODIS data) with primary variable (sparsely distributed biomass/yield model predictions of durum wheat). The model estimates looked strongly spatially correlated with the radiance data (red and NIR bands) and the fusion data approach proved to be quite suitable and flexible to integrate data of different type and support.

Forage quantity estimation from MERIS using band depth parameters

NASA Astrophysics Data System (ADS)

Ullah, Saleem; Yali, Si; Schlerf, Martin

Saleem Ullah1 , Si Yali1 , Martin Schlerf1 Forage quantity is an important factor influencing feeding pattern and distribution of wildlife. The main objective of this study was to evaluate the predictive performance of vegetation indices and band depth analysis parameters for estimation of green biomass using MERIS data. Green biomass was best predicted by NBDI (normalized band depth index) and yielded a calibration R2 of 0.73 and an accuracy (independent validation dataset, n=30) of 136.2 g/m2 (47 % of the measured mean) compared to a much lower accuracy obtained by soil adjusted vegetation index SAVI (444.6 g/m2, 154 % of the mean) and by other vegetation indices. This study will contribute to map and monitor foliar biomass over the year at regional scale which intern can aid the understanding of bird migration pattern. Keywords: Biomass, Nitrogen density, Nitrogen concentration, Vegetation indices, Band depth analysis parameters 1 Faculty of Geo-Information Science and Earth Observation (ITC), University of Twente, The Netherlands

An effective and simple procedure to isolate abundant quantities of biologically active chemopreventive lunasin-protease inhibitor concentrate (LPIC) from soybean

USDA-ARS?s Scientific Manuscript database

Lunasin is a 5-kDa soybean bioactive peptide with demonstrated anti-cancer and anti-inflammatory properties. The use of lunasin as a chemopreventive agent in large-scale animal studies and human clinical trials is hampered by the paucity of large quantities of lunasin. Recently, purification methods...

Weather-based forecasts of California crop yields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lobell, D B; Cahill, K N; Field, C B

2005-09-26

Crop yield forecasts provide useful information to a range of users. Yields for several crops in California are currently forecast based on field surveys and farmer interviews, while for many crops official forecasts do not exist. As broad-scale crop yields are largely dependent on weather, measurements from existing meteorological stations have the potential to provide a reliable, timely, and cost-effective means to anticipate crop yields. We developed weather-based models of state-wide yields for 12 major California crops (wine grapes, lettuce, almonds, strawberries, table grapes, hay, oranges, cotton, tomatoes, walnuts, avocados, and pistachios), and tested their accuracy using cross-validation over themore » 1980-2003 period. Many crops were forecast with high accuracy, as judged by the percent of yield variation explained by the forecast, the number of yields with correctly predicted direction of yield change, or the number of yields with correctly predicted extreme yields. The most successfully modeled crop was almonds, with 81% of yield variance captured by the forecast. Predictions for most crops relied on weather measurements well before harvest time, allowing for lead times that were longer than existing procedures in many cases.« less

Regional crop yield forecasting: a probabilistic approach

NASA Astrophysics Data System (ADS)

de Wit, A.; van Diepen, K.; Boogaard, H.

2009-04-01

Information on the outlook on yield and production of crops over large regions is essential for government services dealing with import and export of food crops, for agencies with a role in food relief, for international organizations with a mandate in monitoring the world food production and trade, and for commodity traders. Process-based mechanistic crop models are an important tool for providing such information, because they can integrate the effect of crop management, weather and soil on crop growth. When properly integrated in a yield forecasting system, the aggregated model output can be used to predict crop yield and production at regional, national and continental scales. Nevertheless, given the scales at which these models operate, the results are subject to large uncertainties due to poorly known weather conditions and crop management. Current yield forecasting systems are generally deterministic in nature and provide no information about the uncertainty bounds on their output. To improve on this situation we present an ensemble-based approach where uncertainty bounds can be derived from the dispersion of results in the ensemble. The probabilistic information provided by this ensemble-based system can be used to quantify uncertainties (risk) on regional crop yield forecasts and can therefore be an important support to quantitative risk analysis in a decision making process.

Modality-independent representations of small quantities based on brain activation patterns.

PubMed

Damarla, Saudamini Roy; Cherkassky, Vladimir L; Just, Marcel Adam

2016-04-01

Machine learning or MVPA (Multi Voxel Pattern Analysis) studies have shown that the neural representation of quantities of objects can be decoded from fMRI patterns, in cases where the quantities were visually displayed. Here we apply these techniques to investigate whether neural representations of quantities depicted in one modality (say, visual) can be decoded from brain activation patterns evoked by quantities depicted in the other modality (say, auditory). The main finding demonstrated, for the first time, that quantities of dots were decodable by a classifier that was trained on the neural patterns evoked by quantities of auditory tones, and vice-versa. The representations that were common across modalities were mainly right-lateralized in frontal and parietal regions. A second finding was that the neural patterns in parietal cortex that represent quantities were common across participants. These findings demonstrate a common neuronal foundation for the representation of quantities across sensory modalities and participants and provide insight into the role of parietal cortex in the representation of quantity information. © 2016 Wiley Periodicals, Inc.

Quantity Discrimination in Wolves (Canis lupus)

PubMed Central

Utrata, Ewelina; Virányi, Zsófia; Range, Friederike

2012-01-01

Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested 11 hand-raised wolves (Canis lupus) in a two-way choice task. We placed a number of food items (one to four) sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris) and coyotes (Canis latrans), our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current set-up are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law. PMID:23181044

Quantity Discrimination in Wolves (Canis lupus).

PubMed

Utrata, Ewelina; Virányi, Zsófia; Range, Friederike

2012-01-01

Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested 11 hand-raised wolves (Canis lupus) in a two-way choice task. We placed a number of food items (one to four) sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris) and coyotes (Canis latrans), our wolves' performance did not improve with decreasing ratio, referred to as Weber's law. However, further studies using larger quantities than we used in the current set-up are still needed to determine whether and when wolves' quantity discrimination conforms to Weber's law.

Of Small Beauties and Large Beasts: The Quality of Distractors on Multiple-Choice Tests Is More Important than Their Quantity

ERIC Educational Resources Information Center

Papenberg, Martin; Musch, Jochen

2017-01-01

In multiple-choice tests, the quality of distractors may be more important than their number. We therefore examined the joint influence of distractor quality and quantity on test functioning by providing a sample of 5,793 participants with five parallel test sets consisting of items that differed in the number and quality of distractors.…

27 CFR 555.213 - Quantity and storage restrictions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

27 CFR 555.213 - Quantity and storage restrictions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

27 CFR 555.213 - Quantity and storage restrictions.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Quantity and storage..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.213 Quantity and storage restrictions. (a) Explosive materials in excess of 300,000 pounds or detonators in...

Forage quantity and quality

USGS Publications Warehouse

Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

2002-01-01

The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

Among-species differences in pollen quality and quantity limitation: implications for endemics in biodiverse hotspots.

PubMed

Alonso, Conchita; Navarro-Fernández, Carmen M; Arceo-Gómez, Gerardo; Meindl, George A; Parra-Tabla, Víctor; Ashman, Tia-Lynn

2013-11-01

Insufficient pollination is a function of quantity and quality of pollen receipt, and the relative contribution of each to pollen limitation may vary with intrinsic plant traits and extrinsic ecological properties. Community-level studies are essential to evaluate variation across species in quality limitation under common ecological conditions. This study examined whether endemic species are more limited by pollen quantity or quality than non-endemic co-flowering species in three endemic-rich plant communities located in biodiversity hotspots of different continents (Andalusia, California and Yucatan). Natural variations in pollen receipt and pollen tube formation were analysed for 20 insect-pollinated plants. Endemic and non-endemic species that co-flowered were paired in order to estimate and compare the quantity and quality components of pre-zygotic pollination success, obtained through piecewise regression analysis of the relationship between pollen grains and pollen tubes of naturally pollinated wilted flowers. Pollen tubes did not frequently exceed the number of ovules per flower. Only the combination of abundant and good quality pollen and a low number of ovules per flower conferred relief from pre-zygotic pollen limitation in the three stochastic pollination environments studied. Quality of pollen receipt was found to be as variable as quantity among study species. The relative pollination success of endemic and non-endemic species, and its quantity and quality components, was community dependent. Assessing both quality and quantity of pollen receipt is key to determining the ovule fertilization potential of both endemic and widespread plants in biodiverse hotspot regions. Large natural variation among flowers of the same species in the two components and pollen tube formation deserves further analysis in order to estimate the environmental, phenotypic and intraindividual sources of variation that may affect how plants evolve to overcome this limitation in

Large number discrimination by mosquitofish.

PubMed

Agrillo, Christian; Piffer, Laura; Bisazza, Angelo

2010-12-22

Recent studies have demonstrated that fish display rudimentary numerical abilities similar to those observed in mammals and birds. The mechanisms underlying the discrimination of small quantities (<4) were recently investigated while, to date, no study has examined the discrimination of large numerosities in fish. Subjects were trained to discriminate between two sets of small geometric figures using social reinforcement. In the first experiment mosquitofish were required to discriminate 4 from 8 objects with or without experimental control of the continuous variables that co-vary with number (area, space, density, total luminance). Results showed that fish can use the sole numerical information to compare quantities but that they preferentially use cumulative surface area as a proxy of the number when this information is available. A second experiment investigated the influence of the total number of elements to discriminate large quantities. Fish proved to be able to discriminate up to 100 vs. 200 objects, without showing any significant decrease in accuracy compared with the 4 vs. 8 discrimination. The third experiment investigated the influence of the ratio between the numerosities. Performance was found to decrease when decreasing the numerical distance. Fish were able to discriminate numbers when ratios were 1:2 or 2:3 but not when the ratio was 3:4. The performance of a sample of undergraduate students, tested non-verbally using the same sets of stimuli, largely overlapped that of fish. Fish are able to use pure numerical information when discriminating between quantities larger than 4 units. As observed in human and non-human primates, the numerical system of fish appears to have virtually no upper limit while the numerical ratio has a clear effect on performance. These similarities further reinforce the view of a common origin of non-verbal numerical systems in all vertebrates.

7 CFR 983.53 - Testing of minimal quantities.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., ARIZONA, AND NEW MEXICO Regulations § 983.53 Testing of minimal quantities. (a) Aflatoxin. Handlers who... § 983.50. (b) Quality. The committee may, with the approval of the Secretary, establish regulations regarding the testing of minimal quantities of pistachios for quality. [74 FR 56540, Nov. 2, 2009] ...

40 CFR 302.5 - Determination of reportable quantities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... reportable quantities listed in Table 302.4 for the contaminant on which the characteristic of toxicity is based. The reportable quantity applies to the waste itself, not merely to the toxic contaminant. If an unlisted hazardous waste exhibits toxicity on the basis of more than one contaminant, the reportable...

Difference in quantity discrimination in dogs and wolves.

PubMed

Range, Friederike; Jenikejew, Julia; Schröder, Isabelle; Virányi, Zsófia

2014-01-01

Certain aspects of social life, such as engaging in intergroup conflicts, as well as challenges posed by the physical environment, may facilitate the evolution of quantity discrimination. In lack of excessive comparative data, one can only hypothesize about its evolutionary origins, but human-raised wolves performed well when they had to choose the larger of two sets of 1-4 food items that had been sequentially placed into two opaque cans. Since in such paradigms, the animals never see the entire content of either can, their decisions are thought to rely on mental representation of the two quantities rather than on some perceptual factors such as the overall volume or surface area of the two amounts. By equaling the time that it takes to enter each quantity into the cans or the number of items entered, one can further rule out the possibility that animals simply choose based on the amount of time needed to present the two quantities. While the wolves performed well even in such a control condition, dogs failed to choose the larger one of two invisible quantities in another study using a similar paradigm. Because this disparity could be explained by procedural differences, in the current study, we set out to test dogs that were raised and kept identically as the previously tested wolves using the same set-up and procedure. Our results confirm the former finding that dogs, in comparison to wolves, have inferior skills to represent quantities mentally. This seems to be in line with Frank's (1980) hypothesis suggesting that domestication altered the information processing of dogs. However, as discussed, also alternative explanations may exist.

Difference in quantity discrimination in dogs and wolves

PubMed Central

Range, Friederike; Jenikejew, Julia; Schröder, Isabelle; Virányi, Zsófia

2014-01-01

Certain aspects of social life, such as engaging in intergroup conflicts, as well as challenges posed by the physical environment, may facilitate the evolution of quantity discrimination. In lack of excessive comparative data, one can only hypothesize about its evolutionary origins, but human-raised wolves performed well when they had to choose the larger of two sets of 1–4 food items that had been sequentially placed into two opaque cans. Since in such paradigms, the animals never see the entire content of either can, their decisions are thought to rely on mental representation of the two quantities rather than on some perceptual factors such as the overall volume or surface area of the two amounts. By equaling the time that it takes to enter each quantity into the cans or the number of items entered, one can further rule out the possibility that animals simply choose based on the amount of time needed to present the two quantities. While the wolves performed well even in such a control condition, dogs failed to choose the larger one of two invisible quantities in another study using a similar paradigm. Because this disparity could be explained by procedural differences, in the current study, we set out to test dogs that were raised and kept identically as the previously tested wolves using the same set-up and procedure. Our results confirm the former finding that dogs, in comparison to wolves, have inferior skills to represent quantities mentally. This seems to be in line with Frank’s (1980) hypothesis suggesting that domestication altered the information processing of dogs. However, as discussed, also alternative explanations may exist. PMID:25477834

A conserved quantity in thin body dynamics

NASA Astrophysics Data System (ADS)

Hanna, J. A.; Pendar, H.

2016-02-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

NASA Astrophysics Data System (ADS)

Liu, Xiao-Wei; Li, Yuan-Cheng

2011-07-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

Nutrient Regulation by Continuous Feeding Removes Limitations on Cell Yield in the Large-Scale Expansion of Mammalian Cell Spheroids

PubMed Central

Weegman, Bradley P.; Nash, Peter; Carlson, Alexandra L.; Voltzke, Kristin J.; Geng, Zhaohui; Jahani, Marjan; Becker, Benjamin B.; Papas, Klearchos K.; Firpo, Meri T.

2013-01-01

Cellular therapies are emerging as a standard approach for the treatment of several diseases. However, realizing the promise of cellular therapies across the full range of treatable disorders will require large-scale, controlled, reproducible culture methods. Bioreactor systems offer the scale-up and monitoring needed, but standard stirred bioreactor cultures do not allow for the real-time regulation of key nutrients in the medium. In this study, β-TC6 insulinoma cells were aggregated and cultured for 3 weeks as a model of manufacturing a mammalian cell product. Cell expansion rates and medium nutrient levels were compared in static, stirred suspension bioreactors (SSB), and continuously fed (CF) SSB. While SSB cultures facilitated increased culture volumes, no increase in cell yields were observed, partly due to limitations in key nutrients, which were consumed by the cultures between feedings, such as glucose. Even when glucose levels were increased to prevent depletion between feedings, dramatic fluctuations in glucose levels were observed. Continuous feeding eliminated fluctuations and improved cell expansion when compared with both static and SSB culture methods. Further improvements in growth rates were observed after adjusting the feed rate based on calculated nutrient depletion, which maintained physiological glucose levels for the duration of the expansion. Adjusting the feed rate in a continuous medium replacement system can maintain the consistent nutrient levels required for the large-scale application of many cell products. Continuously fed bioreactor systems combined with nutrient regulation can be used to improve the yield and reproducibility of mammalian cells for biological products and cellular therapies and will facilitate the translation of cell culture from the research lab to clinical applications. PMID:24204645

Strategies for Estimating Discrete Quantities.

ERIC Educational Resources Information Center

Crites, Terry W.

1993-01-01

Describes the benchmark and decomposition-recomposition estimation strategies and presents five techniques to develop students' estimation ability. Suggests situations involving quantities of candy and popcorn in which the teacher can model those strategies for the students. (MDH)

Natural products phytotoxicity A bioassay suitable for small quantities of slightly water-soluble compounds.

PubMed

Dornbos, D L; Spencer, G F

1990-02-01

A large variety of secondary metabolites that can inhibit germination and/or seedling growth are produced by plants in low quantities. The objective of this study was to develop a bioassay capable of reliably assessing reductions in germination percentage and seedling length of small-seeded plant species caused by exposure to minute quantities of these compounds. The germination and growth of alfalfa (Medicago saliva), annual ryegrass (Lolium multiflorum), and velvetleaf (Abutilon theophrasti) were evaluated against six known phytotoxins from five chemical classes; cinmethylin (a herbicidal cineole derivative) was selected as a comparison standard. Each phytotoxin, dissolved in a suitable organic solvent, was placed on water-agar in small tissue culture wells. After the solvent evaporated, imbibed seeds were placed on the agar; after three days, germination percentages and seedling lengths were measured. Compared to a commonly used filter paper procedure, this modified agar bioassay required smaller quantities of compound per seed for comparable bioassay results. This bioassay also readily permitted the measurement of seedling length, a more sensitive indicator of phytotoxicity than germination. Seedling length decreased sigmoidally as the toxin concentration increased logarithmically. Phytotoxicity was a function of both compound and plant species. Cinmethylin, a grass herbicide, reduced the length of annual ryegrass seedlings by 90-100%, whereas that of alfalfa and velvetleaf was inhibited slightly. The agar bioassay facilitated the rapid and reliable testing of slightly water-soluble compounds, requiring only minute quantities of each compound to give reproducible results.

Search for Proton Decay via p{yields}e{sup +}{pi}{sup 0} and p{yields}{mu}{sup +}{pi}{sup 0} in a Large Water Cherenkov Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishino, H.; Hazama, S.; Higuchi, I.

2009-04-10

We have searched for proton decays via p{yields}e{sup +}{pi}{sup 0} and p{yields}{mu}{sup +}{pi}{sup 0} using data from a 91.7 kt{center_dot}yr exposure of Super-Kamiokande-I and a 49.2 kt{center_dot}yr exposure of Super-Kamiokande-II. No candidate events were observed with expected backgrounds induced by atmospheric neutrinos of 0.3 events for each decay mode. From these results, we set lower limits on the partial lifetime of 8.2x10{sup 33} and 6.6x10{sup 33} years at 90% confidence level for p{yields}e{sup +}{pi}{sup 0} and p{yields}{mu}{sup +}{pi}{sup 0} modes, respectively.

Managment oriented analysis of sediment yield time compression

NASA Astrophysics Data System (ADS)

Smetanova, Anna; Le Bissonnais, Yves; Raclot, Damien; Nunes, João P.; Licciardello, Feliciana; Le Bouteiller, Caroline; Latron, Jérôme; Rodríguez Caballero, Emilio; Mathys, Nicolle; Klotz, Sébastien; Mekki, Insaf; Gallart, Francesc; Solé Benet, Albert; Pérez Gallego, Nuria; Andrieux, Patrick; Moussa, Roger; Planchon, Olivier; Marisa Santos, Juliana; Alshihabi, Omran; Chikhaoui, Mohamed

2016-04-01

The understanding of inter- and intra-annual variability of sediment yield is important for the land use planning and management decisions for sustainable landscapes. It is of particular importance in the regions where the annual sediment yield is often highly dependent on the occurrence of few large events which produce the majority of sediments, such as in the Mediterranean. This phenomenon is referred as time compression, and relevance of its consideration growths with the increase in magnitude and frequency of extreme events due to climate change in many other regions. So far, time compression has ben studied mainly on events datasets, providing high resolution, but (in terms of data amount, required data precision and methods), demanding analysis. In order to provide an alternative simplified approach, the monthly and yearly time compressions were evaluated in eight Mediterranean catchments (of the R-OSMed network), representing a wide range of Mediterranean landscapes. The annual sediment yield varied between 0 to ~27100 Mg•km-2•a-1, and the monthly sediment yield between 0 to ~11600 Mg•km-2•month-1. The catchment's sediment yield was un-equally distributed at inter- and intra-annual scale, and large differences were observed between the catchments. Two types of time compression were distinguished - (i) the inter-annual (based on annual values) and intra- annual (based on monthly values). Four different rainfall-runoff-sediment yield time compression patterns were observed: (i) no time-compression of rainfall, runoff, nor sediment yield, (ii) low time compression of rainfall and runoff, but high compression of sediment yield, (iii) low compression of rainfall and high of runoff and sediment yield, and (iv) low, medium and high compression of rainfall, runoff and sediment yield. All four patterns were present at inter-annual scale, while at intra-annual scale only the two latter were present. This implies that high sediment yields occurred in

[Yield of starch extraction from plantain (Musa paradisiaca). Pilot plant study].

PubMed

Flores-Gorosquera, Emigdia; García-Suárez, Francisco J; Flores-Huicochea, Emmanuel; Núñez-Santiago, María C; González-Soto, Rosalia A; Bello-Pérez, Luis A

2004-01-01

In México, the banana (Musa paradisiaca) is cooked (boiling or deep frying) before being eaten, but the consumption is not very popular and a big quantity of the product is lost after harvesting. The unripe plantain has a high level of starch and due to this the use of banana can be diversified as raw material for starch isolation. The objective of this work was to study the starch yield at pilot plant scale. Experiments at laboratory scale were carried out using the pulp with citric acid to 0,3 % (antioxidant), in order to evaluate the different unitary operations of the process. The starch yield, based on starch presence in the pulp that can be isolated, were between 76 and 86 %, and the values at pilot plant scale were between 63 and 71 %, in different lots of banana fruit. Starch yield values were similar among the diverse lots, showing that the process is reproducible. The lower values of starch recovery at pilot plant scale are due to the loss during sieving operations; however, the amount of starch recovery is good.

Numerical Order and Quantity Processing in Number Comparison

ERIC Educational Resources Information Center

Turconi, Eva; Campbell, Jamie I. D.; Seron, Xavier

2006-01-01

We investigated processing of numerical order information and its relation to mechanisms of numerical quantity processing. In two experiments, performance on a quantity-comparison task (e.g. 2 5; which is larger?) was compared with performance on a relative-order judgment task (e.g. 2 5; ascending or descending order?). The comparison task…

Commercially sterilized mussel meats (Mytilus chilensis): a study on process yield.

PubMed

Almonacid, S; Bustamante, J; Simpson, R; Urtubia, A; Pinto, M; Teixeira, A

2012-06-01

The processing steps most responsible for yield loss in the manufacture of canned mussel meats are the thermal treatments of precooking to remove meats from shells, and thermal processing (retorting) to render the final canned product commercially sterile for long-term shelf stability. The objective of this study was to investigate and evaluate the impact of different combinations of process variables on the ultimate drained weight in the final mussel product (Mytilu chilensis), while verifying that any differences found were statistically and economically significant. The process variables selected for this study were precooking time, brine salt concentration, and retort temperature. Results indicated 2 combinations of process variables producing the widest difference in final drained weight, designated best combination and worst combination with 35% and 29% yield, respectively. Significance of this difference was determined by employing a Bootstrap methodology, which assumes an empirical distribution of statistical error. A difference of nearly 6 percentage points in total yield was found. This represents a 20% increase in annual sales from the same quantity of raw material, in addition to increase in yield, the conditions for the best process included a retort process time 65% shorter than that for the worst process, this difference in yield could have significant economic impact, important to the mussel canning industry. © 2012 Institute of Food Technologists®

Influence of pre-injection control parameters on main-injection fuel quantity for an electronically controlled double-valve fuel injection system of diesel engine

NASA Astrophysics Data System (ADS)

Song, Enzhe; Fan, Liyun; Chen, Chao; Dong, Quan; Ma, Xiuzhen; Bai, Yun

2013-09-01

A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment. The accuracy of the model is validated through comparison with experimental data. The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed. In the spill control valve mode, main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time. In the needle control valve mode, main-injection fuel quantity increases with rising multi-injection dwell time; this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths. Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes; the variation in main-injection quantity is in the range of 1 mm3.

30 CFR 36.45 - Quantity of ventilating air.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

30 CFR 36.45 - Quantity of ventilating air.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

30 CFR 36.45 - Quantity of ventilating air.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Quantity of ventilating air. 36.45 Section 36... TRANSPORTATION EQUIPMENT Test Requirements § 36.45 Quantity of ventilating air. (a) Results of the engine tests shall be used to calculate ventilation (cubic feet of air per minute) that shall be supplied by positive...

Benefits of seasonal forecasts of crop yields

NASA Astrophysics Data System (ADS)

Sakurai, G.; Okada, M.; Nishimori, M.; Yokozawa, M.

2017-12-01

Major factors behind recent fluctuations in food prices include increased biofuel production and oil price fluctuations. In addition, several extreme climate events that reduced worldwide food production coincided with upward spikes in food prices. The stabilization of crop yields is one of the most important tasks to stabilize food prices and thereby enhance food security. Recent development of technologies related to crop modeling and seasonal weather forecasting has made it possible to forecast future crop yields for maize and soybean. However, the effective use of these technologies remains limited. Here we present the potential benefits of seasonal crop-yield forecasts on a global scale for choice of planting day. For this purpose, we used a model (PRYSBI-2) that can well replicate past crop yields both for maize and soybean. This model system uses a Bayesian statistical approach to estimate the parameters of a basic process-based model of crop growth. The spatial variability of model parameters was considered by estimating the posterior distribution of the parameters from historical yield data by using the Markov-chain Monte Carlo (MCMC) method with a resolution of 1.125° × 1.125°. The posterior distributions of model parameters were estimated for each spatial grid with 30 000 MCMC steps of 10 chains each. By using this model and the estimated parameter distributions, we were able to estimate not only crop yield but also levels of associated uncertainty. We found that the global average crop yield increased about 30% as the result of the optimal selection of planting day and that the seasonal forecast of crop yield had a large benefit in and near the eastern part of Brazil and India for maize and the northern area of China for soybean. In these countries, the effects of El Niño and Indian Ocean dipole are large. The results highlight the importance of developing a system to forecast global crop yields.

Multi-look fusion identification: a paradigm shift from quality to quantity in data samples

NASA Astrophysics Data System (ADS)

Wong, S.

2009-05-01

A multi-look identification method known as score-level fusion is found to be capable of achieving very high identification accuracy, even when low quality target signatures are used. Analysis using measured ground vehicle radar signatures has shown that a 97% correct identification rate can be achieved using this multi-look fusion method; in contrast, only a 37% accuracy rate is obtained when single target signature input is used. The results suggest that quantity can be used to replace quality of the target data in improving identification accuracy. With the advent of sensor technology, a large amount of target signatures of marginal quality can be captured routinely. This quantity over quality approach allows maximum exploitation of the available data to improve the target identification performance and this could have the potential of being developed into a disruptive technology.

Quantity Effect of Radial Cracks on the Cracking Propagation Behavior and the Crack Morphology

PubMed Central

Chen, Jingjing; Xu, Jun; Liu, Bohan; Yao, Xuefeng; Li, Yibing

2014-01-01

In this letter, the quantity effect of radial cracks on the cracking propagation behavior as well as the circular crack generation on the impacted glass plate within the sandwiched glass sheets are experimentally investigated via high-speed photography system. Results show that the radial crack velocity on the backing glass layer decreases with the crack number under the same impact conditions during large quantities of repeated experiments. Thus, the “energy conversion factor” is suggested to elucidate the physical relation between the cracking number and the crack propagation speed. Besides, the number of radial crack also takes the determinative effect in the crack morphology of the impacted glass plate. This study may shed lights on understanding the cracking and propagation mechanism in laminated glass structures and provide useful tool to explore the impact information on the cracking debris. PMID:25048684

48 CFR 245.7309-8 - Variations in quantity or weight.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

Kinetically accessible yield (KAY) for redirection of metabolism to produce exo-metabolites

DOE PAGES

Lafontaine Rivera, Jimmy G.; Theisen, Matthew K.; Chen, Po-Wei; ...

2017-04-05

The product formation yield (product formed per unit substrate consumed) is often the most important performance indicator in metabolic engineering. Until now, the actual yield cannot be predicted, but it can be bounded by its maximum theoretical value. The maximum theoretical yield is calculated by considering the stoichiometry of the pathways and cofactor regeneration involved. Here in this paper we found that in many cases, dynamic stability becomes an issue when excessive pathway flux is drawn to a product. This constraint reduces the yield and renders the maximal theoretical yield too loose to be predictive. We propose a more realisticmore » quantity, defined as the kinetically accessible yield (KAY) to predict the maximum accessible yield for a given flux alteration. KAY is either determined by the point of instability, beyond which steady states become unstable and disappear, or a local maximum before becoming unstable. Thus, KAY is the maximum flux that can be redirected for a given metabolic engineering strategy without losing stability. Strictly speaking, calculation of KAY requires complete kinetic information. With limited or no kinetic information, an Ensemble Modeling strategy can be used to determine a range of likely values for KAY, including an average prediction. We first apply the KAY concept with a toy model to demonstrate the principle of kinetic limitations on yield. We then used a full-scale E. coli model (193 reactions, 153 metabolites) and this approach was successful in E. coli for predicting production of isobutanol: the calculated KAY values are consistent with experimental data for three genotypes previously published.« less

A novel rheometer design for yield stress fluids

Treesearch

Joseph R. Samaniuk; Timothy W. Shay; Thatcher W. Root; Daniel J. Klingenberg; C. Tim Scott

2014-01-01

An inexpensive, rapid method for measuring the rheological properties of yield stress fluids is described and tested. The method uses an auger that does not rotate during measurements, and avoids material and instrument-related difficulties, for example, wall slip and the presence of large particles, associated with yield stress fluids. The method can be used...

Large trees losing out to drought

Treesearch

Michael G. Ryan

2015-01-01

Large trees provide many ecological services in forests. They provide seeds for reproduction and food, habitat for plants and animals, and shade for understory vegetation. Older trees and forests store large quantities of carbon, tend to release more water to streams than their more rapidly growing younger counterparts, and provide wood for human use. Mature...

Quantity and structure of word knowledge across adulthood.

PubMed

Salthouse, Timothy A

2014-09-01

Cross-sectional and longitudinal data from moderately large samples of healthy adults confirmed prior findings of age-related declines in measures of the quantity of word knowledge beginning around age 65. Additional analyses were carried out to investigate the interrelations of different types of vocabulary knowledge at various periods in adulthood. Although the organizational structures were similar in adults of different ages, scores on tests with different formats had weaker relations to a higher-order vocabulary construct beginning when adults were in their 60's. The within-person dispersion among different vocabulary test scores was also greater after about 65 years of age. The discovery of quantitative decreases in amount of knowledge occurring at about the same age as qualitative shifts in the structure of knowledge raises the possibility that the two types of changes may be causally linked.

Toward an Economic Definition of Sustainable Yield for Coastal Aquifers

NASA Astrophysics Data System (ADS)

Jenson, J. W.; Habana, N. C.; Lander, M.

2016-12-01

The concept of aquifer sustainable yield has long been criticized, debated, and even disparaged among groundwater hydrologists, but policy-makers and professional water resource managers inevitably ask them for unequivocal answers to such questions as "What is the absolute maximum volume of water that could be sustainably withdrawn from this aquifer?" We submit that it is therefore incumbent upon hydrologists to develop and offer valid practical definitions of sustainable yield that can be usefully applied to given conditions and types of aquifers. In coastal aquifers, water quality—in terms of salinity—is affected by changes in the natural water budget and the volume rate of artificial extraction. In principle, one can identify a family of assay curves for a given aquifer, showing the specific relationships between the quantity and quality of the water extracted under given conditions of recharge. The concept of the assay curve, borrowed from the literature of natural-resource extraction economics, has to our knowledge not yet found its way into the literature of applied hydrology. The relationships between recharge, extraction, and water quality that define the assay curve can be determined empirically from sufficient observations of groundwater response to recharge and extraction and can be estimated from models that have been reliably history-matched ("calibrated") to such data. We thus propose a working definition of sustainable yield for coastal aquifers in terms of the capacity that ultimately could be achieved by an ideal production system, given what is known or can be assumed about the natural limiting conditions. Accordingly, we also offer an approach for defining an ideal production system for a given aquifer, and demonstrate how observational data and/or modeling results can be used to develop assay curves of quality vs. quantity extracted, which can serve as reliable predictive tools for engineers, managers, regulators, and policy

Evaluating differential nuclear DNA yield rates and osteocyte numbers among human bone tissue types: A synchrotron radiation micro-CT approach.

PubMed

Andronowski, Janna M; Mundorff, Amy Z; Pratt, Isaac V; Davoren, Jon M; Cooper, David M L

2017-05-01

Molecular human identification has conventionally focused on DNA sampling from dense, weight-bearing cortical bone tissue, typically from femora or tibiae. A comparison of skeletal elements from three contemporary individuals demonstrated that elements with high quantities of cancellous bone yielded nuclear DNA at the highest rates, suggesting that preferentially sampling cortical bone may be suboptimal (Mundorff & Davoren, 2014). Despite these findings, the reason for the differential DNA yields between cortical and cancellous bone tissues remains unknown. The primary goal of this work is to ascertain whether differences in bone microstructure can be used to explain differential nuclear DNA yield among bone tissue types observed by Mundorff and Davoren (2014), with a focus on osteocytes and the three-dimensional (3D) quantification of their associated lacunae. Osteocytes and other bone cells are recognized to house DNA in bone tissue, thus examining the density of their lacunae may explain why nuclear DNA yield rates differ among bone tissue types. Lacunae were visualized and quantified using synchrotron radiation-based micro-Computed Tomographic imaging (SR micro-CT). Volumes of interest (VOIs) from cortical and cancellous bone tissues (n=129) were comparatively analyzed from the three skeletons sampled for Mundorff and Davoren's (2014) study. Analyses tested the primary hypothesis that the abundance and density of osteocytes (inferred from their lacunar spaces) vary between cortical and cancellous bone tissue types. Results demonstrated that osteocyte lacunar abundance and density vary between cortical and cancellous bone tissue types, with cortical bone VOIs containing a higher lacunar abundance and density. We found that the osteocyte lacunar density values are independent of nuclear DNA yield, suggesting an alternative explanation for the higher nuclear DNA yields from bones with greater quantities of cancellous bone tissue. The use of SR micro-CT allowed for

Children's multiplicative transformations of discrete and continuous quantities.

PubMed

Barth, Hilary; Baron, Andrew; Spelke, Elizabeth; Carey, Susan

2009-08-01

Recent studies have documented an evolutionarily primitive, early emerging cognitive system for the mental representation of numerical quantity (the analog magnitude system). Studies with nonhuman primates, human infants, and preschoolers have shown this system to support computations of numerical ordering, addition, and subtraction involving whole number concepts prior to arithmetic training. Here we report evidence that this system supports children's predictions about the outcomes of halving and perhaps also doubling transformations. A total of 138 kindergartners and first graders were asked to reason about the quantity resulting from the doubling or halving of an initial numerosity (of a set of dots) or an initial length (of a bar). Controls for dot size, total dot area, and dot density ensured that children were responding to the number of dots in the arrays. Prior to formal instruction in symbolic multiplication, division, or rational number, halving (and perhaps doubling) computations appear to be deployed over discrete and possibly continuous quantities. The ability to apply simple multiplicative transformations to analog magnitude representations of quantity may form a part of the toolkit that children use to construct later concepts of rational number.

Fertilizer nitrogen, soil chemical properties, and their determinacy on rice yield: Evidence from 92 paddy fields of a large-scale farm in the Kanto Region of Japan

NASA Astrophysics Data System (ADS)

Li, D.; Nanseki, T.; Chomei, Y.; Yokota, S.

2017-07-01

Rice, a staple crop in Japan, is at risk of decreasing production and its yield highly depends on soil fertility. This study aimed to investigate determinants of rice yield, from the perspectives of fertilizer nitrogen and soil chemical properties. The data were sampled in 2014 and 2015 from 92 peat soil paddy fields on a large-scale farm located in the Kanto Region of Japan. The rice variety used was the most widely planted Koshihikari in Japan. Regression analysis indicated that fertilizer nitrogen significantly affected the yield, with a significant sustained effect to the subsequent year. Twelve soil chemical properties, including pH, cation exchange capacity, content of pyridine base elements, phosphoric acid, and silicic acid, were estimated. In addition to silicic acid, magnesia, in forms of its exchangeable content, saturation, and ratios to potassium and lime, positively affected the yield, while phosphoric acid negatively affected the yield. We assessed the soil chemical properties by soil quality index and principal component analysis. Positive effects were identified for both approaches, with the former performing better in explaining the rice yield. For soil quality index, the individual standardized soil properties and margins for improvement were indicated for each paddy field. Finally, multivariate regression on the principal components identified the most significant properties.

Recognizing Prefixes in Scientific Quantities

NASA Astrophysics Data System (ADS)

Sokolowski, Andrzej

2015-09-01

Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to meters." Similar students' mistakes were reported also by AP Chemistry readers "as in previous years, students still had difficulty converting kJ to J." While traditional teaching focuses on memorizing the symbols of prefixes, little attention is given to helping learners recognize a prefix in a given quantity. I noticed in my teaching practice that by making the processes of identifying prefixes more explicit, students make fewer mistakes on unit conversion. Thus, this paper presents an outline of a lesson that focuses on prefix recognition. It is designed for a first-year college physics class; however, its key points can be addressed to any group of physics students.

Rice yields in tropical/subtropical Asia exhibit large but opposing sensitivities to minimum and maximum temperatures

PubMed Central

Welch, Jarrod R.; Vincent, Jeffrey R.; Auffhammer, Maximilian; Moya, Piedad F.; Dobermann, Achim; Dawe, David

2010-01-01

Data from farmer-managed fields have not been used previously to disentangle the impacts of daily minimum and maximum temperatures and solar radiation on rice yields in tropical/subtropical Asia. We used a multiple regression model to analyze data from 227 intensively managed irrigated rice farms in six important rice-producing countries. The farm-level detail, observed over multiple growing seasons, enabled us to construct farm-specific weather variables, control for unobserved factors that either were unique to each farm but did not vary over time or were common to all farms at a given site but varied by season and year, and obtain more precise estimates by including farm- and site-specific economic variables. Temperature and radiation had statistically significant impacts during both the vegetative and ripening phases of the rice plant. Higher minimum temperature reduced yield, whereas higher maximum temperature raised it; radiation impact varied by growth phase. Combined, these effects imply that yield at most sites would have grown more rapidly during the high-yielding season but less rapidly during the low-yielding season if observed temperature and radiation trends at the end of the 20th century had not occurred, with temperature trends being more influential. Looking ahead, they imply a net negative impact on yield from moderate warming in coming decades. Beyond that, the impact would likely become more negative, because prior research indicates that the impact of maximum temperature becomes negative at higher levels. Diurnal temperature variation must be considered when investigating the impacts of climate change on irrigated rice in Asia. PMID:20696908

Global evidence of positive impacts of freshwater biodiversity on fishery yields.

PubMed

Brooks, Emma Grace Elizabeth; Holland, Robert Alan; Darwall, William Robert Thomas; Eigenbrod, Felix; Tittensor, Derek

2016-05-01

An often-invoked benefit of high biodiversity is the provision of ecosystem services. However, evidence for this is largely based on data from small-scale experimental studies of relationships between biodiversity and ecosystem function that may have little relevance to real-world systems. Here, large-scale biodiversity datasets are used to test the relationship between the yield of inland capture fisheries and species richness from 100 countries. Inland waters of Africa, Europe and parts of Asia. A multimodel inference approach was used to assess inland fishery yields at the country level against species richness, waterside human population, area, elevation and various climatic variables, to determine the relative importance of species richness to fisheries yields compared with other major large-scale drivers. Secondly, the mean decadal variation in fishery yields at the country level for 1981-2010 was regressed against species richness to assess if greater diversity reduces the variability in yields over time. Despite a widespread reliance on targeting just a few species of fish, freshwater fish species richness is highly correlated with yield ( R 2  = 0.55) and remains an important and statistically significant predictor of yield once other macroecological drivers are controlled for. Freshwater richness also has a significant negative relationship with variability of yield over time in Africa ( R 2  = 0.16) but no effect in Europe. The management of inland waters should incorporate the protection of freshwater biodiversity, particularly in countries with the highest-yielding inland fisheries as these also tend to have high freshwater biodiversity. As these results suggest a link between biodiversity and stable, high-yielding fisheries, an important win-win outcome may be possible for food security and conservation of freshwater ecosystems. However, findings also highlight the urgent need for more data to fully understand and monitor the contribution of

From shifting cultivation to teak plantation: effect on overland flow and sediment yield in a montane tropical catchment.

PubMed

Ribolzi, Olivier; Evrard, Olivier; Huon, Sylvain; de Rouw, Anneke; Silvera, Norbert; Latsachack, Keo Oudone; Soulileuth, Bounsamai; Lefèvre, Irène; Pierret, Alain; Lacombe, Guillaume; Sengtaheuanghoung, Oloth; Valentin, Christian

2017-06-21

Soil erosion supplies large quantities of sediments to rivers of Southeastern Asia. It reduces soil fertility of agro-ecosystems located on hillslopes, and it degrades, downstream, water resource quality and leads to the siltation of reservoirs. An increase in the surface area covered with commercial perennial monocultures such as teak plantations is currently observed at the expanse of traditional slash-and-burn cultivation systems in steep montane environments of these regions. The impacts of land-use change on the hydrological response and sediment yields have been investigated in a representative catchment of Laos monitored for 13 years. After the gradual conversion of rice-based shifting cultivation to teak plantation-based systems, overland flow contribution to stream flow increased from 16 to 31% and sediment yield raised from 98 to 609 Mg km -2 . This result is explained by the higher kinetic energy of raindrops falling from the canopy, the virtual absence of understorey vegetation cover to dissipate drop energy and the formation of an impermeable surface crust accelerating the formation and concentration of overland flow. The 25-to-50% lower 137 Cs activities measured in soils collected under mature teak plantations compared to soils under other land uses illustrate the severity of soil erosion processes occurring in teak plantations.

Maximizing RNA yield from archival renal tumors and optimizing gene expression analysis.

PubMed

Glenn, Sean T; Head, Karen L; Teh, Bin T; Gross, Kenneth W; Kim, Hyung L

2010-01-01

Formalin-fixed, paraffin-embedded tissues are widely available for gene expression analysis using TaqMan PCR. Five methods, including 4 commercial kits, for recovering RNA from paraffin-embedded renal tumor tissue were compared. The MasterPure kit from Epicentre produced the highest RNA yield. However, the difference in RNA yield between the kit from Epicenter and Invitrogen's TRIzol method was not significant. Using the top 3 RNA isolation methods, the manufacturers' protocols were modified to include an overnight Proteinase K digestion. Overnight protein digestion resulted in a significant increase in RNA yield. To optimize the reverse transcription reaction, conventional reverse transcription with random oligonucleotide primers was compared to reverse transcription using primers specific for genes of interest. Reverse transcription using gene-specific primers significantly increased the quantity of cDNA detectable by TaqMan PCR. Therefore, expression profiling of formalin-fixed, paraffin-embedded tissue using TaqMan qPCR can be optimized by using the MasterPure RNA isolation kit modified to include an overnight Proteinase K digestion and gene-specific primers during the reverse transcription.

7 CFR 929.14 - Marketable quantity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

7 CFR 929.14 - Marketable quantity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

7 CFR 929.14 - Marketable quantity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

7 CFR 929.14 - Marketable quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

7 CFR 929.14 - Marketable quantity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE CRANBERRIES GROWN IN STATES OF.... Marketable quantity means for a crop year the number of pounds of cranberries necessary to meet the total...

Assessment of the Effect of Climate Change on Grain Yields in China

NASA Astrophysics Data System (ADS)

Chou, J.

2006-12-01

The paper elaborates the social background and research background; makes clear what the key scientific issues need to be resolved and where the difficulties are. In the research area of parasailing the grain yield change caused by climate change, massive works have been done both in the domestic and in the foreign. It is our upcoming work to evaluate how our countrywide climate change information provided by this pattern influence our economic and social development; and how to make related policies and countermeasures. the main idea in this paper is that the grain yield change is by no means the linear composition of social economy function effect and the climatic change function effect. This paper identifies the economic evaluation object, proposes one new concept - climate change output. The grain yields change affected by the social factors and the climatic change working together. Climate change influences the grain yields by the non ¨C linear function from both climate change and social factor changes, not only by climate change itself. Therefore, in my paper, the appraisal object is defined as: The social factors change based on actual social changing situations; under the two kinds of climate change situation, the invariable climate change situation and variable climate change situation; the difference of grain yield outputs is called " climate change output ", In order to solve this problem, we propose a method to analyze and imitate on the historical materials. Giving the condition that the climate is invariable, the social economic factor changes cause the grain yield change. However, this grain yield change is a tentative quantity index, not an actual quantity number. So we use the existing historical materials to exam the climate change output, based on the characteristic that social factor changes greater in year than in age, but the climate factor changes greater in age than in year. The paper proposes and establishes one economy - climate model (C

The Dynamics of Pheromone Gland Synthesis and Release: a Paradigm Shift for Understanding Sex Pheromone Quantity in Female Moths.

PubMed

Foster, Stephen P; Anderson, Karin G; Casas, Jérôme

2018-05-10

Moths are exemplars of chemical communication, especially with regard to specificity and the minute amounts they use. Yet, little is known about how females manage synthesis and storage of pheromone to maintain release rates attractive to conspecific males and why such small amounts are used. We developed, for the first time, a quantitative model, based on an extensive empirical data set, describing the dynamical relationship among synthesis, storage (titer) and release of pheromone over time in a moth (Heliothis virescens). The model is compartmental, with one major state variable (titer), one time-varying (synthesis), and two constant (catabolism and release) rates. The model was a good fit, suggesting it accounted for the major processes. Overall, we found the relatively small amounts of pheromone stored and released were largely a function of high catabolism rather than a low rate of synthesis. A paradigm shift may be necessary to understand the low amounts released by female moths, away from the small quantities synthesized to the (relatively) large amounts catabolized. Future research on pheromone quantity should focus on structural and physicochemical processes that limit storage and release rate quantities. To our knowledge, this is the first time that pheromone gland function has been modeled for any animal.

A Functional Model for Management of Large Scale Assessments.

ERIC Educational Resources Information Center

Banta, Trudy W.; And Others

This functional model for managing large-scale program evaluations was developed and validated in connection with the assessment of Tennessee's Nutrition Education and Training Program. Management of such a large-scale assessment requires the development of a structure for the organization; distribution and recovery of large quantities of…

Simulation of nitrous oxide effluxes, crop yields and soil physical properties using the LandscapeDNDC model in managed ecosystem

NASA Astrophysics Data System (ADS)

Nyckowiak, Jedrzej; Lesny, Jacek; Haas, Edwin; Juszczak, Radoslaw; Kiese, Ralf; Butterbach-Bahl, Klaus; Olejnik, Janusz

2014-05-01

Modeling of nitrous oxide emissions from soil is very complex. Many different biological and chemical processes take place in soils which determine the amount of emitted nitrous oxide. Additionaly, biogeochemical models contain many detailed factors which may determine fluxes and other simulated variables. We used the LandscapeDNDC model in order to simulate N2O emissions, crop yields and soil physical properties from mineral cultivated soils in Poland. Nitrous oxide emissions from soils were modeled for fields with winter wheat, winter rye, spring barley, triticale, potatoes and alfalfa crops. Simulations were carried out for the plots of the Brody arable experimental station of Poznan University of Life Science in western Poland and covered the period 2003 - 2012. The model accuracy and its efficiency was determined by comparing simulations result with measurements of nitrous oxide emissions (measured with static chambers) from about 40 field campaigns. N2O emissions are strongly dependent on temperature and soil water content, hence we compared also simulated soil temperature at 10cm depth and soil water content at the same depth with the daily measured values of these driving variables. We compared also simulated yield quantities for each individual experimental plots with yield quantities which were measured in the period 2003-2012. We conclude that the LandscapeDNDC model is capable to simulate soil N2O emissions, crop yields and physical properties of soil with satisfactorily good accuracy and efficiency.

Recognizing Prefixes in Scientific Quantities

ERIC Educational Resources Information Center

Sokolowski, Andrzej

2015-01-01

Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

48 CFR 52.217-6 - Option for Increased Quantity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

41 CFR 109-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

41 CFR 109-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

41 CFR 109-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

41 CFR 109-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

41 CFR 109-27.102 - Economic order quantity principle.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ...

Visual Working Memory Cannot Trade Quantity for Quality.

PubMed

Ramaty, Ayelet; Luria, Roy

2018-01-01

Two main models have been proposed to describe how visual working memory (WM) allocates its capacity: the slot-model and the continuous resource-model. The purpose of the current study was to test a direct prediction of the resource model suggesting that WM can trade-off between the quantity and quality of the encoded information. Previous research reported equivocal results, with studies that failed to find such a trade-off and other studies that reported a trade-off. Following the design of previous studies, in Experiment 1 we replicated this trade-off, by presenting the memory array for 1200 ms. Experiment 2 failed to observe a trade-off between quantity and quality using a memory array interval of 300 ms (a standard interval for visual WM). Experiment 3 again failed to find this trade-off, when reinstating the 1200 ms memory array interval but adding an articulatory suppression manipulation. We argue that while participants can trade quantity for quality, this pattern depends on verbal encoding and transfer to long-term memory processes that were possible to perform only during the long retention interval. When these processes were eliminated, the trade-off disappeared. Thus, we didn't find any evidence that the trade-off between quantity for quality can occur within visual WM.

A Global Analysis of Light and Charge Yields in Liquid Xenon

DOE PAGES

Lenardo, Brian; Kazkaz, Kareem; Manalaysay, Aaron; ...

2015-11-04

Here, we present an updated model of light and charge yields from nuclear recoils in liquid xenon with a simultaneously constrained parameter set. A global analysis is performed using measurements of electron and photon yields compiled from all available historical data, as well as measurements of the ratio of the two. These data sweep over energies from keV and external applied electric fields from V/cm. The model is constrained by constructing global cost functions and using a simulated annealing algorithm and a Markov Chain Monte Carlo approach to optimize and find confidence intervals on all free parameters in the model.more » This analysis contrasts with previous work in that we do not unnecessarily exclude datasets nor impose artificially conservative assumptions, do not use spline functions, and reduce the number of parameters used in NEST v 0.98. Here, we report our results and the calculated best-fit charge and light yields. These quantities are crucial to understanding the response of liquid xenon detectors in the energy regime important for rare event searches such as the direct detection of dark matter particles.« less

Managing Southeastern US Forests for Increased Water Yield

NASA Astrophysics Data System (ADS)

Acharya, S.; Kaplan, D. A.; Mclaughlin, D. L.; Cohen, M. J.

2017-12-01

Forested lands influence watershed hydrology by affecting water quantity and quality in surface and groundwater systems, making them potentially effective tools for regional water resource planning. In this study, we quantified water use and water yield by pine forests under varying silvicultural management (e.g., high density plantation, thinning, and prescribed burning). Daily forest water use (evapotranspiration, ET) was estimated using continuously monitored soil-moisture in the root-zone at six sites across Florida (USA), each with six plots ranging in forest leaf-area index (LAI). Plots included stands with different rotational ages (from clear-cut to mature pine plantations) and those restored to more historical conditions. Estimated ET relative to potential ET (PET) was strongly associated with LAI, root-zone soil-moisture status, and site hydroclimate; these factors explained 85% of the variation in the ET:PET ratio. Annual water yield (Yw) calculated from these ET estimates and a simple water balance differed significantly among sites and plots (ranging from -0.12 cm/yr to > 100 cm/yr), demonstrating substantive influence of management regimes. LAI strongly influenced Yw in all sites, and a general linear model with forest attributes (LAI and groundcover), hydroclimate, and site characteristics explained >90% of variation in observed Yw. These results can be used to predict water yield changes under different management and climate scenarios and may be useful in the development of payment for ecosystem services approaches that identify water as an important product of forest best management practices.

Lecturer Quality, Quantity and Gender in Colleges of Education in Nigeria

ERIC Educational Resources Information Center

Arubayi, D. O.

2009-01-01

The quality and quantity of lecturers in Tertiary institutions to a great extent determines the quality of graduates. To ensure quality and quantity the Colleges of Education in Nigeria have established internal and external mechanisms. Quantity is determined by the number of students to a given lecturer. Despite the mechanism put forward to…

10 CFR 40.13 - Unimportant quantities of source material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Unimportant quantities of source material. 40.13 Section 40.13 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF SOURCE MATERIAL Exemptions § 40.13 Unimportant quantities of source material. (a) Any person is exempt from the regulations in this part and from...

10 CFR 40.22 - Small quantities of source material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Small quantities of source material. 40.22 Section 40.22 Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF SOURCE MATERIAL General Licenses § 40.22 Small quantities of source material. (a) A general license is hereby issued authorizing commercial and industrial...

Processing Ordinality and Quantity: The Case of Developmental Dyscalculia

PubMed Central

Rubinsten, Orly; Sury, Dana

2011-01-01

In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made “ordered” or “non-ordered” judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information. PMID:21935374

Processing ordinality and quantity: the case of developmental dyscalculia.

PubMed

Rubinsten, Orly; Sury, Dana

2011-01-01

In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

16 CFR 500.7 - Net quantity of contents, method of expression.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity of contents, method of... REGULATIONS UNDER SECTION 4 OF THE FAIR PACKAGING AND LABELING ACT § 500.7 Net quantity of contents, method of expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical...

Micro-quantity tissue digestion for metal measurements by use of a microwave acid-digestion bomb.

PubMed

Nicholson, J R; Savory, M G; Savory, J; Wills, M R

1989-03-01

We describe a simple and convenient method for processing small amounts of tissue samples for trace-metal measurements by atomic absorption spectrometry, by use of a modified Parr microwave digestion bomb. Digestion proceeds rapidly (less than or equal to 90 s) in a sealed Teflon-lined vessel that eliminates contamination or loss from volatilization. Small quantities of tissue (5-100 mg dry weight) are digested in high-purity nitric acid, yielding concentrations of analyte that can be measured directly without further sample manipulation. We analyzed National Institute of Standards and Technology bovine liver Standard Reference Material to verify the accuracy of the technique. We assessed the applicability of the technique to analysis for aluminum in bone by comparison with a dry ashing procedure.

Developing a Hybrid Solar/Wind Powered Drip Irrigation System for Dragon Fruit Yield

NASA Astrophysics Data System (ADS)

Widiastuti, I.; Wijayanto, D. S.

2017-03-01

Irrigation operations take a large amount of water and energy which impact to total costs of crop production. Development of an efficient irrigation supplying precise amount of water and conserving the use of energy can have benefits not only by reducing the operating costs but also by enhancing the farmland productivity. This article presents an irrigation method that promotes sustainable use of water and energy appropriate for a developing tropical country. It proposes a drip irrigation system supported by a combined solar-wind electric power generation system for efficient use of water in dragon fruit cultivation. The electric power generated is used to drive a water pump filling a storage tank for irrigating a 3000 m2 dragon fruit yield in Nguntoronadi, Wonogiri, Indonesia. In designing the irrigation system, the plant’s water requirement was identified based on the value of reference evapotranspiration of the area. A cost/benefit analysis was performed to evaluate the economic feasibility of the proposed scheme. The installation of this solar and wind drip irrigation helps provide sufficient quantity of water to each plant using renewable energy sources which reduce dependence on fossil fuel.

Rice Water use efficiency and yield under continuous and intermittent irrigation

USDA-ARS?s Scientific Manuscript database

In the Brazilian state of Rio Grande do Sul, rice (Oryza sativa L.) is predominantly grown using continuous fl ood irrigation, which requires large quantities of fresh water. Due to increasing scarcity and demand for water, modern agricultural systems need to produce more food with less water. Th e ...

Improving yield of PZT piezoelectric devices on glass substrates

NASA Astrophysics Data System (ADS)

Johnson-Wilke, Raegan L.; Wilke, Rudeger H. T.; Cotroneo, Vincenzo; Davis, William N.; Reid, Paul B.; Schwartz, Daniel A.; Trolier-McKinstry, Susan

2012-10-01

The proposed SMART-X telescope includes adaptive optics systems that use piezoelectric lead zirconate titanate (PZT) films deposited on flexible glass substrates. Several processing constraints are imposed by current designs: the crystallization temperature must be kept below 550 °C, the total stress in the film must be minimized, and the yield on 1 cm2 actuator elements should be < 90%. For this work, RF magnetron sputtering was used to deposit films since chemical solution deposition (CSD) led to warping of large area flexible glass substrates. A PZT 52/48 film that wasdeposited at 4 mTorr and annealed at 550 °C for 24 hours showed no detectable levels of either PbO or pyrochlore second phases. Large area electrodes (1cm x 1 cm) were deposited on 4" glass substrates. Initially, the yield of the devices was low, however, two methods were employed to increase the yield to near 100 %. The first method included a more rigorous cleaning to improve the continuity of the Pt bottom electrode. The second method was to apply 3 V DC across the capacitor structure to burn out regions of defective PZT. The result of this latter method essentially removed conducting filaments in the PZT but left the bulk of the material undamaged. By combining these two methods, the yield on the large area electrodes improved from < 10% to nearly 100%.

Automation of large scale transient protein expression in mammalian cells

PubMed Central

Zhao, Yuguang; Bishop, Benjamin; Clay, Jordan E.; Lu, Weixian; Jones, Margaret; Daenke, Susan; Siebold, Christian; Stuart, David I.; Yvonne Jones, E.; Radu Aricescu, A.

2011-01-01

Traditional mammalian expression systems rely on the time-consuming generation of stable cell lines; this is difficult to accommodate within a modern structural biology pipeline. Transient transfections are a fast, cost-effective solution, but require skilled cell culture scientists, making man-power a limiting factor in a setting where numerous samples are processed in parallel. Here we report a strategy employing a customised CompacT SelecT cell culture robot allowing the large-scale expression of multiple protein constructs in a transient format. Successful protocols have been designed for automated transient transfection of human embryonic kidney (HEK) 293T and 293S GnTI− cells in various flask formats. Protein yields obtained by this method were similar to those produced manually, with the added benefit of reproducibility, regardless of user. Automation of cell maintenance and transient transfection allows the expression of high quality recombinant protein in a completely sterile environment with limited support from a cell culture scientist. The reduction in human input has the added benefit of enabling continuous cell maintenance and protein production, features of particular importance to structural biology laboratories, which typically use large quantities of pure recombinant proteins, and often require rapid characterisation of a series of modified constructs. This automated method for large scale transient transfection is now offered as a Europe-wide service via the P-cube initiative. PMID:21571074

77 FR 43077 - Federal Acquisition Regulation; Information Collection; Economic Purchase Quantity-Supplies

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

...; Information Collection; Economic Purchase Quantity--Supplies AGENCIES: Department of Defense (DOD), General... collection requirement concerning Economic Purchase Quantity--Supplies. Public comments are particularly...: Submit comments identified by Information Collection 9000- 0082, Economic Purchase Quantity--Supplies, by...

Observed, unknown distributions of clinical chemical quantities should be considered to be log-normal: a proposal.

PubMed

Haeckel, Rainer; Wosniok, Werner

2010-10-01

The distribution of many quantities in laboratory medicine are considered to be Gaussian if they are symmetric, although, theoretically, a Gaussian distribution is not plausible for quantities that can attain only non-negative values. If a distribution is skewed, further specification of the type is required, which may be difficult to provide. Skewed (non-Gaussian) distributions found in clinical chemistry usually show only moderately large positive skewness (e.g., log-normal- and χ(2) distribution). The degree of skewness depends on the magnitude of the empirical biological variation (CV(e)), as demonstrated using the log-normal distribution. A Gaussian distribution with a small CV(e) (e.g., for plasma sodium) is very similar to a log-normal distribution with the same CV(e). In contrast, a relatively large CV(e) (e.g., plasma aspartate aminotransferase) leads to distinct differences between a Gaussian and a log-normal distribution. If the type of an empirical distribution is unknown, it is proposed that a log-normal distribution be assumed in such cases. This avoids distributional assumptions that are not plausible and does not contradict the observation that distributions with small biological variation look very similar to a Gaussian distribution.

Quantifying yield gaps in wheat production in Russia

NASA Astrophysics Data System (ADS)

Schierhorn, Florian; Faramarzi, Monireh; Prishchepov, Alexander V.; Koch, Friedrich J.; Müller, Daniel

2014-08-01

Crop yields must increase substantially to meet the increasing demands for agricultural products. Crop yield increases are particularly important for Russia because low crop yields prevail across Russia’s widespread and fertile land resources. However, reliable data are lacking regarding the spatial distribution of potential yields in Russia, which can be used to determine yield gaps. We used a crop growth model to determine the yield potentials and yield gaps of winter and spring wheat at the provincial level across European Russia. We modeled the annual yield potentials from 1995 to 2006 with optimal nitrogen supplies for both rainfed and irrigated conditions. Overall, the results suggest yield gaps of 1.51-2.10 t ha-1, or 44-52% of the yield potential under rainfed conditions. Under irrigated conditions, yield gaps of 3.14-3.30 t ha-1, or 62-63% of the yield potential, were observed. However, recurring droughts cause large fluctuations in yield potentials under rainfed conditions, even when the nitrogen supply is optimal, particularly in the highly fertile black soil areas of southern European Russia. The highest yield gaps (up to 4 t ha-1) under irrigated conditions were detected in the steppe areas in southeastern European Russia along the border of Kazakhstan. Improving the nutrient and water supply and using crop breeds that are adapted to the frequent drought conditions are important for reducing yield gaps in European Russia. Our regional assessment helps inform policy and agricultural investors and prioritize research that aims to increase crop production in this important region for global agricultural markets.

Impact of Spatial Soil and Climate Input Data Aggregation on Regional Yield Simulations

PubMed Central

Hoffmann, Holger; Zhao, Gang; Asseng, Senthold; Bindi, Marco; Biernath, Christian; Constantin, Julie; Coucheney, Elsa; Dechow, Rene; Doro, Luca; Eckersten, Henrik; Gaiser, Thomas; Grosz, Balázs; Heinlein, Florian; Kassie, Belay T.; Kersebaum, Kurt-Christian; Klein, Christian; Kuhnert, Matthias; Lewan, Elisabet; Moriondo, Marco; Nendel, Claas; Priesack, Eckart; Raynal, Helene; Roggero, Pier P.; Rötter, Reimund P.; Siebert, Stefan; Specka, Xenia; Tao, Fulu; Teixeira, Edmar; Trombi, Giacomo; Wallach, Daniel; Weihermüller, Lutz; Yeluripati, Jagadeesh; Ewert, Frank

2016-01-01

We show the error in water-limited yields simulated by crop models which is associated with spatially aggregated soil and climate input data. Crop simulations at large scales (regional, national, continental) frequently use input data of low resolution. Therefore, climate and soil data are often generated via averaging and sampling by area majority. This may bias simulated yields at large scales, varying largely across models. Thus, we evaluated the error associated with spatially aggregated soil and climate data for 14 crop models. Yields of winter wheat and silage maize were simulated under water-limited production conditions. We calculated this error from crop yields simulated at spatial resolutions from 1 to 100 km for the state of North Rhine-Westphalia, Germany. Most models showed yields biased by <15% when aggregating only soil data. The relative mean absolute error (rMAE) of most models using aggregated soil data was in the range or larger than the inter-annual or inter-model variability in yields. This error increased further when both climate and soil data were aggregated. Distinct error patterns indicate that the rMAE may be estimated from few soil variables. Illustrating the range of these aggregation effects across models, this study is a first step towards an ex-ante assessment of aggregation errors in large-scale simulations. PMID:27055028

Impact of Spatial Soil and Climate Input Data Aggregation on Regional Yield Simulations.

PubMed

Hoffmann, Holger; Zhao, Gang; Asseng, Senthold; Bindi, Marco; Biernath, Christian; Constantin, Julie; Coucheney, Elsa; Dechow, Rene; Doro, Luca; Eckersten, Henrik; Gaiser, Thomas; Grosz, Balázs; Heinlein, Florian; Kassie, Belay T; Kersebaum, Kurt-Christian; Klein, Christian; Kuhnert, Matthias; Lewan, Elisabet; Moriondo, Marco; Nendel, Claas; Priesack, Eckart; Raynal, Helene; Roggero, Pier P; Rötter, Reimund P; Siebert, Stefan; Specka, Xenia; Tao, Fulu; Teixeira, Edmar; Trombi, Giacomo; Wallach, Daniel; Weihermüller, Lutz; Yeluripati, Jagadeesh; Ewert, Frank

2016-01-01

We show the error in water-limited yields simulated by crop models which is associated with spatially aggregated soil and climate input data. Crop simulations at large scales (regional, national, continental) frequently use input data of low resolution. Therefore, climate and soil data are often generated via averaging and sampling by area majority. This may bias simulated yields at large scales, varying largely across models. Thus, we evaluated the error associated with spatially aggregated soil and climate data for 14 crop models. Yields of winter wheat and silage maize were simulated under water-limited production conditions. We calculated this error from crop yields simulated at spatial resolutions from 1 to 100 km for the state of North Rhine-Westphalia, Germany. Most models showed yields biased by <15% when aggregating only soil data. The relative mean absolute error (rMAE) of most models using aggregated soil data was in the range or larger than the inter-annual or inter-model variability in yields. This error increased further when both climate and soil data were aggregated. Distinct error patterns indicate that the rMAE may be estimated from few soil variables. Illustrating the range of these aggregation effects across models, this study is a first step towards an ex-ante assessment of aggregation errors in large-scale simulations.

Improved yields for MOST’s using ion implantation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brockman, H. E.

1976-04-01

Conventionally diffused source and drain polysilicon gate MOST's commonly exhibit one type of fault, namely, that of polysilicon-to-diffusion short circuits. Investigations into the yields of large-area devices fabricated using ion-implanted sources and drains are compared with those of diffused structures. An improved technology for the chemical shaping of the polysilicon gates, which improves the yields for both types of devices, is also described. (AIP)

Variation of organic matter quantity and quality in streams at Critical Zone Observatory watersheds

USGS Publications Warehouse

Miller, Matthew P.; Boyer, Elizabeth W.; McKnight, Diane M.; Brown, Michael G.; Gabor, Rachel S.; Hunsaker, Carolyn T.; Iavorivska , Lidiia; Inamdar, Shreeram; Kaplan, Louis A.; Johnson, Dale W.; Lin, Henry; McDowell, William H.; Perdrial, Julia N.

2016-01-01

The quantity and chemical composition of dissolved organic matter (DOM) in surface waters influence ecosystem processes and anthropogenic use of freshwater. However, despite the importance of understanding spatial and temporal patterns in DOM, measures of DOM quality are not routinely included as part of large-scale ecosystem monitoring programs and variations in analytical procedures can introduce artifacts. In this study, we used consistent sampling and analytical methods to meet the objective of defining variability in DOM quantity and quality and other measures of water quality in streamflow issuing from small forested watersheds located within five Critical Zone Observatory sites representing contrasting environmental conditions. Results show distinct separations among sites as a function of water quality constituents. Relationships among rates of atmospheric deposition, water quality conditions, and stream DOM quantity and quality are consistent with the notion that areas with relatively high rates of atmospheric nitrogen and sulfur deposition and high concentrations of divalent cations result in selective transport of DOM derived from microbial sources, including in-stream microbial phototrophs. We suggest that the critical zone as a whole strongly influences the origin, composition, and fate of DOM in streams. This study highlights the value of consistent DOM characterization methods included as part of long-term monitoring programs for improving our understanding of interactions among ecosystem processes as controls on DOM biogeochemistry.

Tradeoffs between vigor and yield for crops grown under different management systems

NASA Astrophysics Data System (ADS)

Simic Milas, Anita; Keller Vincent, Robert; Romanko, Matthew; Feitl, Melina; Rupasinghe, Prabha

2016-04-01

Remote sensing can provide an effective means for rapid and non-destructive monitoring of crop status and biochemistry. Monitoring pattern of traditional vigor algorithms generated from Landsat 8 OLI satellite data represents a robust method that can be widely used to differentiate the status of crops, as well as to monitor nutrient uptake functionality of differently treated seeds grown under different managements. This study considers 24 factorial parcels of winter wheat in 2013, corn in 2014, and soybeans in 2015, grown under four different types of agricultural management. The parcels are located at the Kellogg Biological Station, Long-Term Ecological Research site in the State of Michigan USA. At maturity, the organic crops exhibit significantly higher vigor and significantly lower yield than conventionally managed crops under different treatments. While organic crops invest in their metabolism at the expense of their yield, the conventional crops manage to increase their yield at the expense of their vigor. Landsat 8 OLI is capable of 1) differentiating the biochemical status of crops under different treatments at maturity, and 2) monitoring the tradeoff between crop yield and vigor that can be controlled by the seed treatments and proper conventional applications, with the ultimate goal of increasing food yield and food availability, and 3) distinguishing between organic and conventionally treated crops. Timing, quantity and types of herbicide applications have a great impact on early and pre-harvest vigor, maturity and yield of conventionally treated crops. Satellite monitoring using Landsat 8 is an optimal tool for coordinating agricultural applications, soil practices and genetic coding of the crop to produce higher yield as well as have early crop maturity, desirable in northern climates.

A conserved quantity in thin body dynamics

NASA Astrophysics Data System (ADS)

Hanna, James; Pendar, Hodjat

We use an example from textile processing to illustrate the utility of a conserved quantity associated with metric symmetry in a thin body. This quantity, when combined with the usual linear and angular momentum currents, allows us to construct a four-parameter family of curves representing the equilibria of a rotating, flowing string. To achieve this, we introduce a non-material action of mixed Lagrangian-Eulerian type, applicable to fixed windows of axially-moving systems. We will point out intriguing similarities with Bernoulli's equation, discuss the effects of axial flow on rotating conservative systems, and make connections with 19th- and 20th-century results on the dynamics of cables.

46 CFR 95.17-5 - Quantity of foam required.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

46 CFR 76.17-5 - Quantity of foam required.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 3 2013-10-01 2013-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

46 CFR 76.17-5 - Quantity of foam required.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 3 2012-10-01 2012-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

46 CFR 76.17-5 - Quantity of foam required.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 3 2014-10-01 2014-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

46 CFR 76.17-5 - Quantity of foam required.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

46 CFR 76.17-5 - Quantity of foam required.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 3 2011-10-01 2011-10-01 false Quantity of foam required. 76.17-5 Section 76.17-5... EQUIPMENT Foam Extinguishing Systems, Details § 76.17-5 Quantity of foam required. (a) Area protected. (1... of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall be...

46 CFR 95.17-5 - Quantity of foam required.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

46 CFR 95.17-5 - Quantity of foam required.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

46 CFR 95.17-5 - Quantity of foam required.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

46 CFR 95.17-5 - Quantity of foam required.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Quantity of foam required. 95.17-5 Section 95.17-5... PROTECTION EQUIPMENT Foam Extinguishing Systems, Details § 95.17-5 Quantity of foam required. (a) Area... blanket of foam over the entire tank top or bilge of the space protected. The arrangement of piping shall...

Possible changes to arable crop yields by 2050

PubMed Central

Jaggard, Keith W.; Qi, Aiming; Ober, Eric S.

2010-01-01

By 2050, the world population is likely to be 9.1 billion, the CO2 concentration 550 ppm, the ozone concentration 60 ppb and the climate warmer by ca 2°C. In these conditions, what contribution can increased crop yield make to feeding the world? CO2 enrichment is likely to increase yields of most crops by approximately 13 per cent but leave yields of C4 crops unchanged. It will tend to reduce water consumption by all crops, but this effect will be approximately cancelled out by the effect of the increased temperature on evaporation rates. In many places increased temperature will provide opportunities to manipulate agronomy to improve crop performance. Ozone concentration increases will decrease yields by 5 per cent or more. Plant breeders will probably be able to increase yields considerably in the CO2-enriched environment of the future, and most weeds and airborne pests and diseases should remain controllable, so long as policy changes do not remove too many types of crop-protection chemicals. However, soil-borne pathogens are likely to be an increasing problem when warmer weather will increase their multiplication rates; control is likely to need a transgenic approach to breeding for resistance. There is a large gap between achievable yields and those delivered by farmers, even in the most efficient agricultural systems. A gap is inevitable, but there are large differences between farmers, even between those who have used the same resources. If this gap is closed and accompanied by improvements in potential yields then there is a good prospect that crop production will increase by approximately 50 per cent or more by 2050 without extra land. However, the demands for land to produce bio-energy have not been factored into these calculations. PMID:20713388

Possible changes to arable crop yields by 2050.

PubMed

Jaggard, Keith W; Qi, Aiming; Ober, Eric S

2010-09-27

By 2050, the world population is likely to be 9.1 billion, the CO(2) concentration 550 ppm, the ozone concentration 60 ppb and the climate warmer by ca 2 degrees C. In these conditions, what contribution can increased crop yield make to feeding the world? CO(2) enrichment is likely to increase yields of most crops by approximately 13 per cent but leave yields of C4 crops unchanged. It will tend to reduce water consumption by all crops, but this effect will be approximately cancelled out by the effect of the increased temperature on evaporation rates. In many places increased temperature will provide opportunities to manipulate agronomy to improve crop performance. Ozone concentration increases will decrease yields by 5 per cent or more. Plant breeders will probably be able to increase yields considerably in the CO(2)-enriched environment of the future, and most weeds and airborne pests and diseases should remain controllable, so long as policy changes do not remove too many types of crop-protection chemicals. However, soil-borne pathogens are likely to be an increasing problem when warmer weather will increase their multiplication rates; control is likely to need a transgenic approach to breeding for resistance. There is a large gap between achievable yields and those delivered by farmers, even in the most efficient agricultural systems. A gap is inevitable, but there are large differences between farmers, even between those who have used the same resources. If this gap is closed and accompanied by improvements in potential yields then there is a good prospect that crop production will increase by approximately 50 per cent or more by 2050 without extra land. However, the demands for land to produce bio-energy have not been factored into these calculations.

A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

USGS Publications Warehouse

Cravotta, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

2010-01-01

Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

On the Hardy Space Theory of Compensated Compactness Quantities

NASA Astrophysics Data System (ADS)

Lindberg, Sauli

2017-05-01

We make progress on a problem of Coifman et al. (J Math Pures Appl (9) 72(3): 247-286, 1993) by showing that the Jacobian operator J does not map {W^{1,n}(Rn, Rn) onto the Hardy space H1(Rn) for any {n ≥ 2}. The related question about the surjectivity of {J : dot{W}^{1,n}(Rn,Rn) to H1(Rn) is still open. The second main result and its variants reduce the proof of H1 regularity of a large class of compensated compactness quantities to an integration by parts or easy arithmetic, and applications are presented. Furthermore, we exhibit a class of nonlinear partial differential operators in which weak sequential continuity is a strictly stronger condition than H1 regularity, shedding light on another question of Coifman, Lions, Meyer and Semmes.

Influence of land use on the quantity and quality of runoff along Israel's coastal strip

NASA Astrophysics Data System (ADS)

Goldshleger, Naftaly; Asaf, Lior; Maor, Alon; Garzuzi, Jamil Jamil

2013-04-01

This study presents an analysis of the quantity and quality of urban runoff from various land uses by remote-sensing and GIS technology coupled with hydrological and chemical monitoring. The study areas were located in the cities of Herzliya and Ra'anana, in Israel's coastal plain, where extensive urbanization has taken place over the last 30 years. Land uses in urban basins were analyzed; rain and runoff were measured and sampled at measurement stations representing different land uses (residential, industrial, commercial, roads, gas station). The aim was to analyze land uses by different remote-sensing and GIS techniques, to evaluate the quality and quantity of urban storm water from various land uses, and to verify a method for predicting the impact of urban land uses on quantity and quality of urban storm water. The quality of urban storm water from residential areas was generally very high, and the water is suitable for reuse or direct recharge into the local aquifer. In light of the serious state of the Israeli water sector and the large amounts of unused runoff produced by Israel's cities, together with the high quality of urban storm water drained from the residential areas, it is important to exploit this water source

Mathematical and statistical analysis of the effect of boron on yield parameters of wheat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rawashdeh, Hamzeh; Sala, Florin; Boldea, Marius

The main objective of this research is to investigate the effect of foliar applications of boron at different growth stages on yield and yield parameters of wheat. The contribution of boron in achieving yield parameters is described by second degree polynomial equations, with high statistical confidence (p<0.01; F theoretical < F calculated, according to ANOVA test, for Alfa = 0.05). Regression analysis, based on R{sup 2} values obtained, made it possible to evaluate the particular contribution of boron to the realization of yield parameters. This was lower for spike length (R{sup 2} = 0.812), thousand seeds weight (R{sup 2} =more » 0.850) and higher in the case of the number of spikelets (R{sup 2} = 0.936) and the number of seeds on a spike (R{sup 2} = 0.960). These results confirm that boron plays an important part in achieving the number of seeds on a spike in the case of wheat, as the contribution of this element to the process of flower fertilization is well-known. In regards to productivity elements, the contribution of macroelements to yield quantity is clear, the contribution of B alone being R{sup 2} = 0.868.« less

Looking for Water in the Woods: Quantifying the Potential for Forest Management to Increase Regional Water Yield

NASA Astrophysics Data System (ADS)

Acharya, S.; Kaplan, D. A.; Mclaughlin, D. L.; Cohen, M. J.

2014-12-01

Water scarcity presents a crucial challenge for water resource managers charged with maintaining hydrologic resources for domestic, industrial, and agricultural use while protecting natural systems. Forest lands are critical to the functioning of the hydrologic cycle in many watersheds, affecting the quantity, quality, and timing of water delivered to surface and groundwater systems. While the hydrologic impacts of forest growth and removal have been shown to be substantial in watersheds around the globe, data and models connecting forest management to water use and regional hydrology are generally lacking. We propose that water-focused forest management has the potential to deliver a "new" source of water to surface and groundwater resources. To test this hypothesis, we developed a statistical model of water yield in southeastern US pine stands as a function of forest stand structure and ecosystem water use. Model results suggest a potential increase in water yield of up to 64% for pine stands managed at lower basal areas relative to those managed according to standard silvicultural practices. At the watershed scale, the magnitude of this potential water yield enhancement is driven by existing land use and forest management; evaluated for a large watershed in NE Florida, this potential increase is in excess of 200 million gallons per day (equivalent to 20% of the anthropogenic water use in the watershed). While useful for exploration, our statistical model also highlighted critical sources of uncertainty, including the effects of climatic variation, between-site variability, water use in young pine stands, and prescribed fire. Thus, in ongoing work we are comparing the effects of specific land management actions (e.g., thinning, clearcutting, and fire) on water yield across a gradient of environmental conditions (soil type, aquifer confinement, and climate) using a novel combination of in-situ soil moisture and groundwater monitoring. These data are being used to

Water yield issues in the jarrah forest of south-western Australia

NASA Astrophysics Data System (ADS)

Ruprecht, J. K.; Stoneman, G. L.

1993-10-01

The jarrah forest of south-western Australia produces little streamflow from moderate rainfall. Water yield from water supply catchments for Perth, Western Australia, are low, averaging 71 mm (7% of annual rainfall). The low water yields are attributed to the large soil water storage available for continuous use by the forest vegetation. A number of water yield studies in south-western Australia have examined the impact on water yield of land use practices including clearing for agricultural development, forest harvesting and regeneration, forest thinning and bauxite mining. A permanent reduction in forest cover by clearing for agriculture led to permanent increases of water yield of approximately 28% of annual rainfall in a high rainfall catchment. Thinning of a high rainfall catchment led to an increase in water yield of 20% of annual rainfall. However, it is not clear for how long the increased water yield will persist. Forest harvesting and regeneration have led to water yield increases of 16% of annual rainfall. The subsequent recovery of vegetation cover has led to water yields returning to pre-disturbance levels after an estimated 12-15 years. Bauxite mining of a high rainfall catchment led to a water yield increase of 8% of annual rainfall, followed by a return to pre-disturbance water yield after 12 years. The magnitude of specific streamflow generation mechanisms in small catchments subject to forest disturbance vary considerably, typically in a number of distinct stages. The presence of a permanent groundwater discharge area was shown to be instrumental in determining the magnitude of the streamflow response after forest disturbance. The long-term prognosis for water yield from areas subject to forest thinning, harvesting and regeneration, and bauxite mining are uncertain, owing to the complex interrelationship between vegetation cover, tree height and age, and catchment evapotranspiration. Management of the forest for water yield needs to acknowledge

Logistics and quality control for DNA sampling in large multicenter studies.

PubMed

Nederhand, R J; Droog, S; Kluft, C; Simoons, M L; de Maat, M P M

2003-05-01

To study associations between genetic variation and disease, large bio-banks need to be created in multicenter studies. Therefore, we studied the effects of storage time and temperature on DNA quality and quantity in a simulation experiment with storage up to 28 days frozen, at 4 degrees C and at room temperature. In the simulation experiment, the conditions did not influence the amount or quality of DNA to an unsatisfactory level. However, the amount of extracted DNA was decreased in frozen samples and in samples that were stored for > 7 days at room temperature. In a sample of patients from 24 countries of the EUROPA trial obtained by mail with transport times up to 1 month DNA yield and quality were adequate. From these results we conclude that transport of non-frozen blood by ordinary mail is usable and practical for DNA isolation for polymerase chain reaction in clinical and epidemiological studies.

Partitioning potential fish yields from the Great Lakes

USGS Publications Warehouse

Loftus, D.H.; Olver, C.H.; Brown, Edward H.; Colby, P.J.; Hartman, Wilbur L.; Schupp, D.H.

1987-01-01

We proposed and implemented procedures for partitioning future fish yields from the Great Lakes into taxonomic components. These projections are intended as guidelines for Great Lakes resource managers and scientists. Attainment of projected yields depends on restoration of stable fish communities containing some large piscivores that will use prey efficiently, continuation of control of the sea lamprey (Petromyzon marinus), and restoration of high-quality fish habitat. Because Great Lakes fish communities were harmonic before their collapse, we used their historic yield properties as part of the basis for projecting potential yields of rehabilitated communities. This use is qualified, however, because of possible inaccuracies in the wholly commercial yield data, the presence now of greatly expanded sport fisheries that affect yield composition and magnitude, and some possibly irreversible changes since the 1950s in the various fish communities themselves. We predict that total yields from Lakes Superior, Huron, and Ontario will be increased through rehabilitation, while those from Lakes Michigan and Erie will decline. Salmonines and coregonines will dominate future yields from the upper lakes. The Lake Erie fishery will continue to yield mostly rainbow smelt (Osmerus mordax), but the relative importance of percids, especially of walleye (Stizostedion vitreum vitreum) will increase. In Lake Ontario, yields of salmonines will be increased. Managers will have to apply the most rigorous management strictures to major predator species.

Assessment of impacts of agricultural and climate change scenarios on watershed water quantity and quality, and crop production

NASA Astrophysics Data System (ADS)

Teshager, Awoke D.; Gassman, Philip W.; Schoof, Justin T.; Secchi, Silvia

2016-08-01

Modeling impacts of agricultural scenarios and climate change on surface water quantity and quality provides useful information for planning effective water, environmental and land use policies. Despite the significant impacts of agriculture on water quantity and quality, limited literature exists that describes the combined impacts of agricultural land use change and climate change on future bioenergy crop yields and watershed hydrology. In this study, the soil and water assessment tool (SWAT) eco-hydrological model was used to model the combined impacts of five agricultural land use change scenarios and three downscaled climate pathways (representative concentration pathways, RCPs) that were created from an ensemble of eight atmosphere-ocean general circulation models (AOGCMs). These scenarios were implemented in a well-calibrated SWAT model for the intensively farmed and tiled Raccoon River watershed (RRW) located in western Iowa. The scenarios were executed for the historical baseline, early century, mid-century and late century periods. The results indicate that historical and more corn intensive agricultural scenarios with higher CO2 emissions consistently result in more water in the streams and greater water quality problems, especially late in the 21st century. Planting more switchgrass, on the other hand, results in less water in the streams and water quality improvements relative to the baseline. For all given agricultural landscapes simulated, all flow, sediment and nutrient outputs increase from early-to-late century periods for the RCP4.5 and RCP8.5 climate scenarios. We also find that corn and switchgrass yields are negatively impacted under RCP4.5 and RCP8.5 scenarios in the mid- and late 21st century.

Measurement of LYSO Intrinsic Light Yield Using Electron Excitation

NASA Astrophysics Data System (ADS)

Turtos, Rosana Martinez; Gundacker, Stefan; Pizzichemi, Marco; Ghezzi, Alessio; Pauwels, Kristof; Auffray, Etiennette; Lecoq, Paul; Paganoni, Marco

2016-04-01

The determination of the intrinsic light yield (LYint) of scintillating crystals, i.e. number of optical photons created per amount of energy deposited, constitutes a key factor in order to characterize and optimize their energy and time resolution. However, until now measurements of this quantity are affected by large uncertainties and often rely on corrections for bulk absorption and surface/edge state. The novel idea presented in this contribution is based on the confinement of the scintillation emission in the central upper part of a 10 mm cubic crystal using a 1.5 MeV electron beam with diameter of 1 mm. A black non-reflective pinhole aligned with the excitation point is used to fix the light extraction solid angle (narrower than total reflection angle), which then sets a light cone travel path through the crystal. The final number of photoelectrons detected using a Hamamatsu R2059 photomultiplier tube (PMT) was corrected for the extraction solid angle, the Fresnel reflection coefficient and quantum efficiency (QE) of the PMT. The total number of optical photons produced per energy deposited was found to be 40000 ph/MeV ± 9% (syst) ±3% (stat) for LYSO. Simulations using Geant4 were successfully compared to light output measurements of 2 × 2 mm2 section crystals with lengths of 5-30 mm, in order to validate the light transport model and set a limit on Light Transfer Efficiency estimations.

RF Modal Quantity Gaging

NASA Technical Reports Server (NTRS)

Vanleuven, K.

1989-01-01

The primary objective is to provide a concept of a radio frequency (RF) modal resonance technique which is being investigated as a method for gaging the quantities of subcritical cryogenic propellants in metallic tanks. Of special interest are the potential applications of the technique to microgravity propellant gaging situations. The results of concept testing using cryogenic oxygen, hydrogen, and nitrogen, as well as paraffin simulations of microgravity fluid orientations, are reported. These test results were positive and showed that the gaging concept was viable.

Train hard, sleep well? Perceived training load, sleep quantity and sleep stage distribution in elite level athletes.

PubMed

Knufinke, Melanie; Nieuwenhuys, Arne; Geurts, Sabine A E; Møst, Els I S; Maase, Kamiel; Moen, Maarten H; Coenen, Anton M L; Kompier, Michiel A J

2018-04-01

Sleep is essential for recovery and performance in elite athletes. While it is generally assumed that exercise benefits sleep, high training load may jeopardize sleep and hence limit adequate recovery. To examine this, the current study assessed objective sleep quantity and sleep stage distributions in elite athletes and calculated their association with perceived training load. Mixed-methods. Perceived training load, actigraphy and one-channel EEG recordings were collected among 98 elite athletes during 7 consecutive days of regular training. Actigraphy revealed total sleep durations of 7:50±1:08h, sleep onset latencies of 13±15min, wake after sleep onset of 33±17min and sleep efficiencies of 88±5%. Distribution of sleep stages indicated 51±9% light sleep, 21±8% deep sleep, and 27±7% REM sleep. On average, perceived training load was 5.40±2.50 (scale 1-10), showing large daily variability. Mixed-effects models revealed no alteration in sleep quantity or sleep stage distributions as a function of day-to-day variation in preceding training load (all p's>.05). Results indicate healthy sleep durations, but elevated wake after sleep onset, suggesting a potential need for sleep optimization. Large proportions of deep sleep potentially reflect an elevated recovery need. With sleep quantity and sleep stage distributions remaining irresponsive to variations in perceived training load, it is questionable whether athletes' current sleep provides sufficient recovery after strenuous exercise. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Radiation Protection Quantities for Near Earth Environments

NASA Technical Reports Server (NTRS)

Clowdsley, Martha S.; Wilson, John W.; Kim, Myung-Hee; Anderson, Brooke M.; Nealy, John E.

2004-01-01

As humans travel beyond the protection of the Earth's magnetic field and mission durations grow, risk due to radiation exposure will increase and may become the limiting factor for such missions. Here, the dosimetric quantities recommended by the National Council on Radiation Protection and Measurements (NCRP) for the evaluation of health risk due to radiation exposure, effective dose and gray-equivalent to eyes, skin, and blood forming organs (BFO), are calculated for several near Earth environments. These radiation protection quantities are evaluated behind two different shielding materials, aluminum and polyethylene. Since exposure limits for missions beyond low Earth orbit (LEO) have not yet been defined, results are compared to limits recommended by the NCRP for LEO operations.

Optomechanical Control of Quantum Yield in Trans-Cis Ultrafast Photoisomerization of a Retinal Chromophore Model.

PubMed

Valentini, Alessio; Rivero, Daniel; Zapata, Felipe; García-Iriepa, Cristina; Marazzi, Marco; Palmeiro, Raúl; Fdez Galván, Ignacio; Sampedro, Diego; Olivucci, Massimo; Frutos, Luis Manuel

2017-03-27

The quantum yield of a photochemical reaction is one of the most fundamental quantities in photochemistry, as it measures the efficiency of the transduction of light energy into chemical energy. Nature has evolved photoreceptors in which the reactivity of a chromophore is enhanced by its molecular environment to achieve high quantum yields. The retinal chromophore sterically constrained inside rhodopsin proteins represents an outstanding example of such a control. In a more general framework, mechanical forces acting on a molecular system can strongly modify its reactivity. Herein, we show that the exertion of tensile forces on a simplified retinal chromophore model provokes a substantial and regular increase in the trans-to-cis photoisomerization quantum yield in a counterintuitive way, as these extension forces facilitate the formation of the more compressed cis photoisomer. A rationale for the mechanochemical effect on this photoisomerization mechanism is also proposed. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Micro-Costing Quantity Data Collection Methods

PubMed Central

Frick, Kevin D.

2009-01-01

Background Micro-costing studies collect detailed data on resources utilized and the value of those resources. Such studies are useful for estimating the cost of new technologies or new community-based interventions, for producing estimates in studies that include non-market goods, and for studying within-procedure cost variation. Objectives This objectives of this paper were to (1) describe basic micro-costing methods focusing on quantity data collection; and (2) suggest a research agenda to improve methods in and the interpretation of micro-costing Research Design Examples in the published literature were used to illustrate steps in the methods of gathering data (primarily quantity data) for a micro-costing study. Results Quantity data collection methods that were illustrated in the literature include the use of (1) administrative databases at single facilities, (2) insurer administrative data, (3) forms applied across multiple settings, (4) an expert panel, (5) surveys or interviews of one or more types of providers; (6) review of patient charts, (7) direct observation, (8) personal digital assistants, (9) program operation logs, and (10) diary data. Conclusions Future micro-costing studies are likely to improve if research is done to compare the validity and cost of different data collection methods; if a critical review is conducted of studies done to date; and if the combination of the results of the first two steps described are used to develop guidelines that address common limitations, critical judgment points, and decisions that can reduce limitations and improve the quality of studies. PMID:19536026

SU-E-T-235: Data Mining for Evaluating Treatment Performances Over a Large Quantity of Data to Monitor and Improve SBRT Workflow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, W; Bayhealth Medical Center, Dover, DE; Chu, A

Purpose: To quality assure a large quantity of retrospective treatment cases for treatment performances by randomly sampling is inefficient. Here we provide a method to efficiently monitor and investigate the QA of SBRT workflow over Mosaiq. Methods: The code developed with Microsoft SQL Server Management Studio 2008R2 and VBA was used for retrieving and sorting data from Mosaiq (version 2.3–2.6 during 2012–2015). SBRT patients were filtered by fractional dose over 350cGy and total fraction number less than 6, which SBRT prescriptions were defined. The quality assurance on the SBRT workflow was focused on the treatment deliveries such as patient positioningmore » setup, CBCT indicated offsets and couch shifted corrections. The treatment delivery were done by Varian Truebeam systems and the record/verify by Mosaiq. Results: Total 82 SBRT patients corresponding to 103 courses and 854 CBCT images were found by the retrieval query. Most centers record daily pre-treatment (Pre-Tx: before treatment shift) image-guided shifts along treatment course for inter-fraction motion record, and it is useful to also verify it with post-treatment imaging (Post-Tx: after treatment CBCT verification) to verify intra-fraction motion. Analyzing the details of daily recorded shifts can reveals the information of patient-setup and staff’s record/verify behaviors. 3 examples were provided as solid evidences and on-going rectification for preventing future mistakes. Conclusions: The report gave feasible examples for inspector to verify a large amount of data during site investigation. This program can also be extended to a scheduled data mining with software to periodical analyze the timely records in Mosaiq, for example, a various control charts for different QA purposes. As the current trend of automation in radiation therapy field, the data mining would be a necessary tool in the future, just as the automatic plan quality evaluation has been under development in Eclipse.« less

Study of B{yields}{lambda}{sub c}{lambda}{sub c} and B{yields}{lambda}{sub c}{lambda}{sub c}K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, H.-Y.; Hsiao, Y.-K.; Chua, C.-K.

2009-06-01

We study the doubly charmful two-body and three-body baryonic B decays B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -} and B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -}K. As pointed out before, a naive estimate of the branching ratio O(10{sup -8}) for the latter decay is too small by 3 to 4 orders of magnitude compared to experiment. Previously, it has been shown that a large enhancement for the {lambda}{sub c}{sup +}{lambda}{sub c}{sup -}K production can occur due to a charmoniumlike resonance (e.g. X(4630) discovered by Belle) with a mass near the {lambda}{sub c}{lambda}{sub c} threshold. Motivated by the BABAR's observation of a resonance in themore » {lambda}{sub c}K system with a mass of order 2930 MeV, we study in this work the contribution to B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -}K from the intermediate state {xi}{sub c}(2980) which is postulated to be a first positive-parity excited D-wave charmed baryon state. Assuming that a soft qq quark pair is produced through the {sigma} and {pi} meson exchanges in the configuration for B{yields}{xi}{sub c}(2980){lambda}{sub c} and {lambda}{sub c}{lambda}{sub c}, it is found that branching ratios of B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -}K and B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -} are of order 3.5x10{sup -4} and 5x10{sup -5}, respectively, in agreement with experiment except that the prediction for the {lambda}{sub c}{lambda}{sub c}K{sup -} is slightly smaller. In conjunction with our previous analysis, we conclude that the enormously large rate of B{yields}{lambda}{sub c}{sup +}{lambda}{sub c}{sup -}K arises from the resonances {xi}{sub c}(2980) and X(4630)« less

Vineyard microclimate and yield under different plastic covers.

PubMed

Holcman, Ester; Sentelhas, Paulo Cesar; Conceição, Marco Antônio Fonseca; Couto, Hilton Thadeu Zarate

2018-06-01

The use of plastic cover in vineyards minimizes effects of adverse weather conditions. The northwest of São Paulo State is one of the largest grape producing regions in Brazil; however, few studies investigate the effects of different plastic covers on vineyards in this region. This study compared the effect of black shading screen (BSS) and braided polypropylene film (BPF) on BRS Morena vineyard microclimate, grown on an overhead trellis system in the northwestern São Paulo. The experiments were carried out during three growing seasons (2012-2014). BSS allowed superior incoming solar radiation (SR) transmissivity, resulting in higher net radiation (Rn), and higher ratio between photosynthetically active (PAR) and SR. No differences were observed between the average air temperatures (T) and relative humidity (RH) of covered environments (BPF and BSS) and outside condition (automatic weather station-AWS), due to high air circulation, despite wind speed (WS) reduction caused by plastic covers. BPF provided better conditions for vineyard growth with higher fruit yield than vineyard under BSS regarding the number of shoots with bunches per plant, bunch and stem weights, longitudinal diameter of berries, quantity of fertile buds per shoot, and yield per shoot and per plant. BPF covers also influenced leaf size and growth speed of plants in vineyards.

Vineyard microclimate and yield under different plastic covers

NASA Astrophysics Data System (ADS)

Holcman, Ester; Sentelhas, Paulo Cesar; Conceição, Marco Antônio Fonseca; Couto, Hilton Thadeu Zarate

2017-12-01

The use of plastic cover in vineyards minimizes effects of adverse weather conditions. The northwest of São Paulo State is one of the largest grape producing regions in Brazil; however, few studies investigate the effects of different plastic covers on vineyards in this region. This study compared the effect of black shading screen (BSS) and braided polypropylene film (BPF) on BRS Morena vineyard microclimate, grown on an overhead trellis system in the northwestern São Paulo. The experiments were carried out during three growing seasons (2012-2014). BSS allowed superior incoming solar radiation (SR) transmissivity, resulting in higher net radiation (Rn), and higher ratio between photosynthetically active (PAR) and SR. No differences were observed between the average air temperatures (T) and relative humidity (RH) of covered environments (BPF and BSS) and outside condition (automatic weather station-AWS), due to high air circulation, despite wind speed (WS) reduction caused by plastic covers. BPF provided better conditions for vineyard growth with higher fruit yield than vineyard under BSS regarding the number of shoots with bunches per plant, bunch and stem weights, longitudinal diameter of berries, quantity of fertile buds per shoot, and yield per shoot and per plant. BPF covers also influenced leaf size and growth speed of plants in vineyards.

Vineyard microclimate and yield under different plastic covers

NASA Astrophysics Data System (ADS)

Holcman, Ester; Sentelhas, Paulo Cesar; Conceição, Marco Antônio Fonseca; Couto, Hilton Thadeu Zarate

2018-06-01

The use of plastic cover in vineyards minimizes effects of adverse weather conditions. The northwest of São Paulo State is one of the largest grape producing regions in Brazil; however, few studies investigate the effects of different plastic covers on vineyards in this region. This study compared the effect of black shading screen (BSS) and braided polypropylene film (BPF) on BRS Morena vineyard microclimate, grown on an overhead trellis system in the northwestern São Paulo. The experiments were carried out during three growing seasons (2012-2014). BSS allowed superior incoming solar radiation (SR) transmissivity, resulting in higher net radiation (Rn), and higher ratio between photosynthetically active (PAR) and SR. No differences were observed between the average air temperatures (T) and relative humidity (RH) of covered environments (BPF and BSS) and outside condition (automatic weather station-AWS), due to high air circulation, despite wind speed (WS) reduction caused by plastic covers. BPF provided better conditions for vineyard growth with higher fruit yield than vineyard under BSS regarding the number of shoots with bunches per plant, bunch and stem weights, longitudinal diameter of berries, quantity of fertile buds per shoot, and yield per shoot and per plant. BPF covers also influenced leaf size and growth speed of plants in vineyards.

7 CFR 1435.303 - Adjustment of the overall allotment quantity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

7 CFR 1435.303 - Adjustment of the overall allotment quantity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

7 CFR 1435.303 - Adjustment of the overall allotment quantity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

7 CFR 1435.303 - Adjustment of the overall allotment quantity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

7 CFR 1435.303 - Adjustment of the overall allotment quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS SUGAR PROGRAM Flexible Marketing Allotments For Sugar § 1435.303 Adjustment of the overall allotment quantity. (a) The... than 85 percent of the estimated quantity of sugar for domestic human consumption for the crop year: (1...

Seasoning small quantities of lumber

Treesearch

E.F. Rasmussen

1965-01-01

The owner of a small quantity of green lumber or logs is often confronted with seasoning it to a state of dryness suitable for use in furniture, wood carving, or other handiwork. He cannot follow the practice of commercial mills, which employ dry kilns for the purpose. because kilns are too costly. On the other hand, air seasoning outdoors usually does not dry lumber...

Quantity-activity relationship of denitrifying bacteria and environmental scaling in streams of a forested watershed

USGS Publications Warehouse

O'Connor, B.L.; Hondzo, Miki; Dobraca, D.; LaPara, T.M.; Finlay, J.A.; Brezonik, P.L.

2006-01-01

The spatial variability of subreach denitrification rates in streams was evaluated with respect to controlling environmental conditions, molecular examination of denitrifying bacteria, and dimensional analysis. Denitrification activities ranged from 0 and 800 ng-N gsed-1 d-1 with large variations observed within short distances (<50 m) along stream reaches. A log-normal probability distribution described the range in denitrification activities and was used to define low (16% of the probability distributibn), medium (68%), and high (16%) denitrification potential groups. Denitrifying bacteria were quantified using a competitive polymerase chain reaction (cPCR) technique that amplified the nirK gene that encodes for nitrite reductase. Results showed a range of nirK quantities from 103 to 107 gene-copy-number gsed.-1 A nonparametric statistical test showed no significant difference in nirK quantifies among stream reaches, but revealed that samples with a high denitrification potential had significantly higher nirK quantities. Denitrification activity was positively correlated with nirK quantities with scatter in the data that can be attributed to varying environmental conditions along stream reaches. Dimensional analysis was used to evaluate denitrification activities according to environmental variables that describe fluid-flow properties, nitrate and organic material quantities, and dissolved oxygen flux. Buckingham's pi theorem was used to generate dimensionless groupings and field data were used to determine scaling parameters. The resulting expressions between dimensionless NO3- flux and dimensionless groupings of environmental variables showed consistent scaling, which indicates that the subreach variability in denitrification rates can be predicted by the controlling physical, chemical, and microbiological conditions. Copyright 2006 by the American Geophysical Union.

Acrolein Yields in Mainstream Smoke From Commercial Cigarette and Little Cigar Tobacco Products.

PubMed

Cecil, Todd L; Brewer, Tim M; Young, Mimy; Holman, Matthew R

2017-07-01

Many carbonyls are produced from the combustion of tobacco products and many of these carbonyls are harmful or potentially harmful constituents of mainstream cigarette smoke. One carbonyl of particular interest is acrolein, which is formed from the incomplete combustion of organic matter and the most significant contributor to non-cancer respiratory effects from cigarette smoke. Sheet-wrapped cigars, also known as "little cigars," are a type of tobacco products that have not been extensively investigated in literature. This study uses standard cigarette testing protocols to determine the acrolein yields from sheet-wrapped cigars. Sheet-wrapped cigar and cigarette products were tested by derivatizing the mainstream smoke with 2,4-dinitrophenylhydrazine (DNPH) solution and then quantifying the derivatives using conventional analytical systems. The results demonstrate that sheet-wrapped cigars can be tested for acrolein yields in mainstream smoke using the same methods used for the evaluation of cigarettes. The variability in the sheet-wrapped cigars and cigarettes under the International Organization for Standardization smoking regimen is statistically similar at the 95% confidence interval; however, increased variability is observed for sheet-wrapped cigar products under the Health Canada Intense (CI) smoking regimen. The amount of acrolein released by smoking sheet-wrapped cigars can be measured using standard smoking regimen currently used for cigarettes. The sheet-wrapped cigars were determined to yield similar quantity of acrolein from commercial cigarette products using two standard smoking regimens. This article reports on the measured quantity of acrolein from 15 commercial sheet-wrapped cigars using a validated standard smoking test method that derivatizes acrolein in the mainstream smoke with DNPH solution, and uses Liquid Chromatography/Ultra-Violet Detection (LC/UV) for separation and detection. These acrolein yields were similar to the levels found in

Agricultural Management Practices Explain Variation in Global Yield Gaps of Major Crops

NASA Astrophysics Data System (ADS)

Mueller, N. D.; Gerber, J. S.; Ray, D. K.; Ramankutty, N.; Foley, J. A.

2010-12-01

The continued expansion and intensification of agriculture are key drivers of global environmental change. Meeting a doubling of food demand in the next half-century will further induce environmental change, requiring either large cropland expansion into carbon- and biodiversity-rich tropical forests or increasing yields on existing croplands. Closing the “yield gaps” between the most and least productive farmers on current agricultural lands is a necessary and major step towards preserving natural ecosystems and meeting future food demand. Here we use global climate, soils, and cropland datasets to quantify yield gaps for major crops using equal-area climate analogs. Consistent with previous studies, we find large yield gaps for many crops in Eastern Europe, tropical Africa, and parts of Mexico. To analyze the drivers of yield gaps, we collected sub-national agricultural management data and built a global dataset of fertilizer application rates for over 160 crops. We constructed empirical crop yield models for each climate analog using the global management information for 17 major crops. We find that our climate-specific models explain a substantial amount of the global variation in yields. These models could be widely applied to identify management changes needed to close yield gaps, analyze the environmental impacts of agricultural intensification, and identify climate change adaptation techniques.

Microdosimetry of DNA conformations: relation between direct effect of (60)Co gamma rays and topology of DNA geometrical models in the calculation of A-, B- and Z-DNA radiation-induced damage yields.

PubMed

Semsarha, Farid; Raisali, Gholamreza; Goliaei, Bahram; Khalafi, Hossein

2016-05-01

In order to obtain the energy deposition pattern of ionizing radiation in the nanometric scale of genetic material and to investigate the different sensitivities of the DNA conformations, direct effects of (60)Co gamma rays on the three A, B and Z conformations of DNA have been studied. For this purpose, single-strand breaks (SSB), double-strand breaks (DSB), base damage (BD), hit probabilities and three microdosimetry quantities (imparted energy, mean chord length and lineal energy) in the mentioned DNA conformations have been calculated and compared by using GEometry ANd Tracking 4 (Geant4) toolkit. The results show that A-, B- and Z-DNA conformations have the highest yields of DSB (1.2 Gy(-1) Gbp(-1)), SSB (25.2 Gy(-1) Gbp(-1)) and BD (4.81 Gy(-1) Gbp(-1)), respectively. Based on the investigation of direct effects of radiation, it can be concluded that the DSB yield is largely correlated to the topological characteristics of DNA models, although the SSB yield is not. Moreover, according to the comparative results of the present study, a reliable candidate parameter for describing the relationship between DNA damage yields and geometry of DNA models in the theoretical radiation biology research studies would be the mean chord length (4 V/S) of the models.

7 CFR 35.13 - Minimum quantity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

Yield of Echocardiogram and Predictors of Positive Yield in Pediatric Patients: A Study in an Urban, Community-Based Outpatient Pediatric Cardiology Clinic.

PubMed

Billa, Ramya Deepthi; Szpunar, Susan; Zeinali, Lida; Anne, Premchand

2018-01-01

The yield of outpatient echocardiograms varies based on the indication for the echocardiogram and the age of the patient. The purpose of this study was to determine the cumulative yield of outpatient echocardiograms by age group and reason for the test. A secondary aim was to determine the predictors of a positive echocardiogram in an outpatient cardiology clinic at a large community teaching hospital. We retrospectively reviewed the charts of 891 patients who had a first-time echocardiogram between 2011 and 2015. Positive yield was defined as echocardiographic findings that explained the reason for the echocardiogram. The overall positive yield was 8.2%. Children between birth and 3 months of age had the highest yield (34.2%), and children between 12 and 18 years of age had the lowest yield (1%). Patients with murmurs (18.1%) had the highest yield compared with patients with other signs or symptoms. By age group and reason, the highest yields were as follows: 0 to 3 months of age, murmur (39.2%); 4 to 11 months of age, >1 symptom (50%); and 1 to 5 years of age, shortness of breath (66.7%). Based on our study, the overall yield of echocardiograms in the outpatient pediatric setting is low. Age and symptoms should be considered before ordering an echocardiogram.

Soil fungal communities in a Castanea sativa (chestnut) forest producing large quantities of Boletus edulis sensu lato (porcini): where is the mycelium of porcini?

PubMed

Peintner, Ursula; Iotti, Mirco; Klotz, Petra; Bonuso, Enrico; Zambonelli, Alessandra

2007-04-01

A study was conducted in a Castanea sativa forest that produces large quantities of the edible mushroom porcini (Boletus edulis sensu lato). The primary aim was to study porcini mycelia in the soil, and to determine if there were any possible ecological and functional interactions with other dominant soil fungi. Three different approaches were used: collection and morphological identification of fruiting bodies, morphological and molecular identification of ectomycorrhizae by rDNA-ITS sequence analyses and molecular identification of the soil mycelia by ITS clone libraries. Soil samples were taken directly under basidiomes of Boletus edulis, Boletus aestivalis, Boletus aereus and Boletus pinophilus. Thirty-nine ectomycorrhizal fungi were identified on root tips whereas 40 fungal species were found in the soil using the cloning technique. The overlap between above- and below-ground fungal communities was very low. Boletus mycelia, compared with other soil fungi, were rare and with scattered distribution, whereas their fruiting bodies dominated the above-ground fungal community. Only B. aestivalis ectomycorrhizae were relatively abundant and detected as mycelia in the soil. No specific fungus-fungus association was found. Factors triggering formation of mycorrhizae and fructification of porcini appear to be too complex to be simply explained on the basis of the amount of fungal mycelia in the soil.

Quantities for assessing high photon doses to the body: a calculational approach.

PubMed

Eakins, Jonathan S; Ainsbury, Elizabeth A

2018-06-01

Tissue reactions are the most clinically significant consequences of high-dose exposures to ionising radiation. However, currently there is no universally recognized dose quantity that can be used to assess and report generalised risks to individuals following whole body exposures in the high-dose range. In this work, a number of potential dose quantities are presented and discussed, with mathematical modelling techniques employed to compare them and explore when their differences are most or least manifest. The results are interpreted to propose the average (D GRB ) of the absorbed doses to the stomach, small intestine, red bone marrow, and brain as the optimum quantity for informing assessments of risk. A second, maximally conservative dose quantity (D Max ) is also suggested, which places limits on any under-estimates resulting from the adoption of D GRB . The primary aim of this work is to spark debate, with further work required to refine the final choice of quantity or quantities most appropriate for the full range of different potential exposure scenarios.

Large-scale generation of cell-derived nanovesicles

NASA Astrophysics Data System (ADS)

Jo, W.; Kim, J.; Yoon, J.; Jeong, D.; Cho, S.; Jeong, H.; Yoon, Y. J.; Kim, S. C.; Gho, Y. S.; Park, J.

2014-09-01

Exosomes are enclosed compartments that are released from cells and that can transport biological contents for the purpose of intercellular communications. Research into exosomes is hindered by their rarity. In this article, we introduce a device that uses centrifugal force and a filter with micro-sized pores to generate a large quantity of cell-derived nanovesicles. The device has a simple polycarbonate structure to hold the filter, and operates in a common centrifuge. Nanovesicles are similar in size and membrane structure to exosomes. Nanovesicles contain intracellular RNAs ranging from microRNA to mRNA, intracellular proteins, and plasma membrane proteins. The quantity of nanovesicles produced using the device is 250 times the quantity of naturally secreted exosomes. Also, the quantity of intracellular contents in nanovesicles is twice that in exosomes. Nanovesicles generated from murine embryonic stem cells can transfer RNAs to target cells. Therefore, this novel device and the nanovesicles that it generates are expected to be used in exosome-related research, and can be applied in various applications such as drug delivery and cell-based therapy.

Expressions for IAU 2000 precession quantities

NASA Astrophysics Data System (ADS)

Capitaine, N.; Wallace, P. T.; Chapront, J.

2003-12-01

A new precession-nutation model for the Celestial Intermediate Pole (CIP) was adopted by the IAU in 2000 (Resolution B1.6). The model, designated IAU 2000A, includes a nutation series for a non-rigid Earth and corrections for the precession rates in longitude and obliquity. The model also specifies numerical values for the pole offsets at J2000.0 between the mean equatorial frame and the Geocentric Celestial Reference System (GCRS). In this paper, we discuss precession models consistent with IAU 2000A precession-nutation (i.e. MHB 2000, provided by Mathews et al. \\cite{Mathews02}) and we provide a range of expressions that implement them. The final precession model, designated P03, is a possible replacement for the precession component of IAU 2000A, offering improved dynamical consistency and a better basis for future improvement. As a preliminary step, we present our expressions for the currently used precession quantities zetaA, thetaA, zA, in agreement with the MHB corrections to the precession rates, that appear in the IERS Conventions 2000. We then discuss a more sophisticated method for improving the precession model of the equator in order that it be compliant with the IAU 2000A model. In contrast to the first method, which is based on corrections to the t terms of the developments for the precession quantities in longitude and obliquity, this method also uses corrections to their higher degree terms. It is essential that this be used in conjunction with an improved model for the ecliptic precession, which is expected, given the known discrepancies in the IAU 1976 expressions, to contribute in a significant way to these higher degree terms. With this aim in view, we have developed new expressions for the motion of the ecliptic with respect to the fixed ecliptic using the developments from Simon et al. (\\cite{Simon94}) and Williams (\\cite{Williams94}) and with improved constants fitted to the most recent numerical planetary ephemerides. We have then used

Impacts of biofuels production alternatives on water quantity and quality in the Iowa River Basin

USGS Publications Warehouse

Wu, Y.; Liu, S.

2012-01-01

Corn stover as well as perennial grasses like switchgrass (Panicum virgatum) and miscanthus are being considered as candidates for the second generation biofuel feedstocks. However, the challenges to biofuel development are its effects on the environment, especially water quality. This study evaluates the long-term impacts of biofuel production alternatives (e.g., elevated corn stover removal rates and the potential land cover change) on an ecosystem with a focus on biomass production, soil erosion, water quantity and quality, and soil nitrate nitrogen concentration at the watershed scale. The Soil and Water Assessment Tool (SWAT) was modified for setting land cover change scenarios and applied to the Iowa River Basin (a tributary of the Upper Mississippi River Basin). Results show that biomass production can be sustained with an increased stover removal rate as long as the crop demand for nutrients is met with appropriate fertilization. Although a drastic increase (4.7–70.6%) in sediment yield due to erosion and a slight decrease (1.2–3.2%) in water yield were estimated with the stover removal rate ranging between 40% and 100%, the nitrate nitrogen load declined about 6–10.1%. In comparison to growing corn, growing either switchgrass or miscanthus can reduce sediment erosion greatly. However, land cover changes from native grass to switchgrass or miscanthus would lead to a decrease in water yield and an increase in nitrate nitrogen load. In contrast to growing switchgrass, growing miscanthus is more productive in generating biomass, but its higher water demand may reduce water availability in the study area.

19 CFR 132.5 - Merchandise imported in excess of quota quantities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... quantities. (a) Absolute quota merchandise. Absolute quota merchandise imported in excess of the quantity... merchandise. Merchandise imported in excess of either an absolute or a tariff-rate quota may be held for the...

19 CFR 132.5 - Merchandise imported in excess of quota quantities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... quantities. (a) Absolute quota merchandise. Absolute quota merchandise imported in excess of the quantity... merchandise. Merchandise imported in excess of either an absolute or a tariff-rate quota may be held for the...

Association between work-family conflict and smoking quantity among daily smokers.

PubMed

Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

2013-11-01

Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

48 CFR 16.504 - Indefinite-quantity contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... quantity based on market research, trends on recent contracts for similar supplies or services, survey of... are unique or highly specialized; (2) Based on the contracting officer's knowledge of the market, more...

14 CFR 29.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Placards § 29.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or... extending from the calibrated zero reading to the lowest reading obtainable in level flight. ...

14 CFR 25.1553 - Fuel quantity indicator.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Placards § 25.1553 Fuel quantity indicator. If the unusable fuel supply for any tank exceeds one gallon, or... extending from the calibrated zero reading to the lowest reading obtainable in level flight. ...

Method and Apparatus for Measuring Radiation Quantities

DOEpatents

Roberts, N O

1955-01-25

This patent application describes a compact dosimeter for measuring X-ray and gamma radiation by the use of solutions which undergo a visible color change upon exposure to a predetermined quantity of radiation.

Environmental factors controlling spatial variation in sediment yield in a central Andean mountain area

NASA Astrophysics Data System (ADS)

Molina, Armando; Govers, Gerard; Poesen, Jean; Van Hemelryck, Hendrik; De Bièvre, Bert; Vanacker, Veerle

2008-06-01

A large spatial variability in sediment yield was observed from small streams in the Ecuadorian Andes. The objective of this study was to analyze the environmental factors controlling these variations in sediment yield in the Paute basin, Ecuador. Sediment yield data were calculated based on sediment volumes accumulated behind checkdams for 37 small catchments. Mean annual specific sediment yield (SSY) shows a large spatial variability and ranges between 26 and 15,100 Mg km - 2 year - 1 . Mean vegetation cover (C, fraction) in the catchment, i.e. the plant cover at or near the surface, exerts a first order control on sediment yield. The fractional vegetation cover alone explains 57% of the observed variance in ln(SSY). The negative exponential relation (SSY = a × e- b C) which was found between vegetation cover and sediment yield at the catchment scale (10 3-10 9 m 2), is very similar to the equations derived from splash, interrill and rill erosion experiments at the plot scale (1-10 3 m 2). This affirms the general character of an exponential decrease of sediment yield with increasing vegetation cover at a wide range of spatial scales, provided the distribution of cover can be considered to be essentially random. Lithology also significantly affects the sediment yield, and explains an additional 23% of the observed variance in ln(SSY). Based on these two catchment parameters, a multiple regression model was built. This empirical regression model already explains more than 75% of the total variance in the mean annual sediment yield. These results highlight the large potential of revegetation programs for controlling sediment yield. They show that a slight increase in the overall fractional vegetation cover of degraded land is likely to have a large effect on sediment production and delivery. Moreover, they point to the importance of detailed surface vegetation data for predicting and modeling sediment production rates.

21 CFR 701.13 - Declaration of net quantity of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) COSMETICS COSMETIC LABELING Package Form § 701.13 Declaration of net quantity of contents. (a) The label of a cosmetic in package form shall bear a declaration of the net quantity of contents. This... weight or measure. The statement shall be in terms of fluid measure if the cosmetic is liquid or in terms...

Consumer-Resource Dynamics: Quantity, Quality, and Allocation

PubMed Central

Getz, Wayne M.; Owen-Smith, Norman

2011-01-01

Background The dominant paradigm for modeling the complexities of interacting populations and food webs is a system of coupled ordinary differential equations in which the state of each species, population, or functional trophic group is represented by an aggregated numbers-density or biomass-density variable. Here, using the metaphysiological approach to model consumer-resource interactions, we formulate a two-state paradigm that represents each population or group in a food web in terms of both its quantity and quality. Methodology and Principal Findings The formulation includes an allocation function controlling the relative proportion of extracted resources to increasing quantity versus elevating quality. Since lower quality individuals senesce more rapidly than higher quality individuals, an optimal allocation proportion exists and we derive an expression for how this proportion depends on population parameters that determine the senescence rate, the per-capita mortality rate, and the effects of these rates on the dynamics of the quality variable. We demonstrate that oscillations do not arise in our model from quantity-quality interactions alone, but require consumer-resource interactions across trophic levels that can be stabilized through judicious resource allocation strategies. Analysis and simulations provide compelling arguments for the necessity of populations to evolve quality-related dynamics in the form of maternal effects, storage or other appropriate structures. They also indicate that resource allocation switching between investments in abundance versus quality provide a powerful mechanism for promoting the stability of consumer-resource interactions in seasonally forcing environments. Conclusions/Significance Our simulations show that physiological inefficiencies associated with this switching can be favored by selection due to the diminished exposure of inefficient consumers to strong oscillations associated with the well-known paradox of

The effects of quantity and depth of processing on children's time perception.

PubMed

Arlin, M

1986-08-01

Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

PubMed Central

2013-01-01

Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

Interactions between plant nutrients, water and carbon dioxide as factors limiting crop yields

PubMed Central

Gregory, P. J.; Simmonds, L. P.; Warren, G. P.

1997-01-01

Biomass production of annual crops is often directly proportional to the amounts of radiation intercepted, water transpired and nutrients taken up. In many places the amount of rainfall during the period of rapid crop growth is less than the potential rate of evaporation, so that depletion of stored soil water is commonplace. The rate of mineralization of nitrogen (N) from organic matter and the processes of nutrient loss are closely related to the availability of soil water. Results from Kenya indicate the rapid changes in nitrate availability following rain.
Nutrient supply has a large effect on the quantity of radiation intercepted and hence, biomass production. There is considerable scope for encouraging canopy expansion to conserve water by reducing evaporation from the soil surface in environments where it is frequently rewetted, and where the unsaturated hydraulic conductivity of the soil is sufficient to supply water at the energy limited rate (e.g. northern Syria). In regions with high evaporative demand and coarse-textured soils (e.g. Niger), transpiration may be increased by management techniques that reduce drainage.
Increases in atmospheric [CO2] are likely to have only a small impact on crop yields when allowance is made for the interacting effects of temperature, and water and nutrient supply.

Upper Limits for Power Yield in Thermal, Chemical, and Electrochemical Systems

NASA Astrophysics Data System (ADS)

Sieniutycz, Stanislaw

2010-03-01

We consider modeling and power optimization of energy converters, such as thermal, solar and chemical engines and fuel cells. Thermodynamic principles lead to expressions for converter's efficiency and generated power. Efficiency equations serve to solve the problems of upgrading or downgrading a resource. Power yield is a cumulative effect in a system consisting of a resource, engines, and an infinite bath. While optimization of steady state systems requires using the differential calculus and Lagrange multipliers, dynamic optimization involves variational calculus and dynamic programming. The primary result of static optimization is the upper limit of power, whereas that of dynamic optimization is a finite-rate counterpart of classical reversible work (exergy). The latter quantity depends on the end state coordinates and a dissipation index, h, which is the Hamiltonian of the problem of minimum entropy production. In reacting systems, an active part of chemical affinity constitutes a major component of the overall efficiency. The theory is also applied to fuel cells regarded as electrochemical flow engines. Enhanced bounds on power yield follow, which are stronger than those predicted by the reversible work potential.

Varieties of Quantity Estimation in Children

ERIC Educational Resources Information Center

Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

2015-01-01

In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

7 CFR 966.53 - Minimum quantities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Minimum quantities. 966.53 Section 966.53 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... will be free from regulations issued or effective pursuant to §§ 966.42, 966.52, 966.54, 966.60, or any...

Yield gaps and yield relationships in US soybean production systems

USDA-ARS?s Scientific Manuscript database

The magnitude of yield gaps (YG) (potential yield – farmer yield) provides some indication of the prospects for increasing crop yield to meet the food demands of future populations. Quantile regression analysis was applied to county soybean [Glycine max (L.) Merrill] yields (1971 – 2011) from Kentuc...

High-quality and -quantity DNA extraction from frozen archival blood clots for genotyping of single-nucleotide polymorphisms.

PubMed

Bank, Steffen; Nexø, Bjørn Andersen; Andersen, Vibeke; Vogel, Ulla; Andersen, Paal Skytt

2013-06-01

The recovery of biological samples for genetic epidemiological studies can be cumbersome. Blood clots are routinely collected for serological examinations. However, the extraction of DNA from blood clots can be difficult and often results in low yields. The aim was to compare the efficiency of commercial purification kits for extracting DNA from long-term frozen clotted blood. Serum tubes with clotted blood were stored at -20°C for 1 to 2.5 years before DNA extraction. DNA was extracted from 10 blood clot samples using PureGene (Qiagen) with and without glycogen, the QIAamp DNA Micro kit (Qiagen), and the Nucleospin 96 Blood kit (Macherey-Nagel). Furthermore, blood clots from 1055 inflammatory bowel disease patients were purified using the Maxwell 16 Blood purification kit (Promega). The DNA was extracted according to the manufacturers` instructions and real-time PCR and the A(260)/A(280) ratio were used to evaluate the quality of the extracted DNA. The highest DNA yield was obtained by the Maxwell 16 Blood purification kit (Promega) with a median of 4.90 μg (range 0.8-25 μg) pr 300 μL total blood. PureGene with glycogen (Qiagen) had the second highest yield with a median of 0.65 μg (range 0.5-2.6 μg) pr 300 μL total blood. The yield obtained by the different commercial kits varied considerably. Our work demonstrates that high-quality and -quantity DNA can be extracted with the Maxwell 16 Blood purification kit (Promega) from cryopreserved blood clots, even after prolonged storage. The recovered DNA served as a reliable PCR template for single-nucleotide polymorphism assays.

Memory for Multiple Cache Locations and Prey Quantities in a Food-Hoarding Songbird

PubMed Central

Armstrong, Nicola; Garland, Alexis; Burns, K. C.

2012-01-01

Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes), a food-hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with (1) the number of cache sites containing prey rewards and (2) the length of time separating cache creation and retrieval (retention interval). Results showed that subjects generally performed above-chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3, and 4 cache sites from between 1, 10, and 60 s. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to 1 min long retention intervals without training. PMID:23293622

Memory for multiple cache locations and prey quantities in a food-hoarding songbird.

PubMed

Armstrong, Nicola; Garland, Alexis; Burns, K C

2012-01-01

Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes), a food-hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with (1) the number of cache sites containing prey rewards and (2) the length of time separating cache creation and retrieval (retention interval). Results showed that subjects generally performed above-chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3, and 4 cache sites from between 1, 10, and 60 s. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to 1 min long retention intervals without training.

Arsenic Treatment Residuals: Quantities, Characteristics and Disposal

EPA Science Inventory

This presentation provides information on the quantities, the characteristics and the disposal options for the common arsenic removal technologies. The technologies consist of adsorption media, iron removal, coagulation/filtration and ion exchange. The information for the prese...

Impacts of variability in cellulosic biomass yields on energy security.

PubMed

Mullins, Kimberley A; Matthews, H Scott; Griffin, W Michael; Anex, Robert

2014-07-01

The practice of modeling biomass yields on the basis of deterministic point values aggregated over space and time obscures important risks associated with large-scale biofuel use, particularly risks related to drought-induced yield reductions that may become increasingly frequent under a changing climate. Using switchgrass as a case study, this work quantifies the variability in expected yields over time and space through switchgrass growth modeling under historical and simulated future weather. The predicted switchgrass yields across the United States range from about 12 to 19 Mg/ha, and the 80% confidence intervals range from 20 to 60% of the mean. Average yields are predicted to decrease with increased temperatures and weather variability induced by climate change. Feedstock yield variability needs to be a central part of modeling to ensure that policy makers acknowledge risks to energy supplies and develop strategies or contingency plans that mitigate those risks.

Role of the N*(1535) resonance and the {pi}{sup -}p{yields}KY amplitudes in the OZI forbidden {pi}N{yields}{phi}N reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doering, M.; Oset, E.; Zou, B. S.

2008-08-15

We study the {pi}N{yields}{phi}N reaction close to the {phi}N threshold within the chiral unitary approach, by combining the {pi}{sup -}p{yields}K{sup +}{sigma}{sup -},{pi}{sup -}p{yields}K{sup 0}{sigma}{sup 0}, and {pi}{sup -}p{yields}K{sup 0}{lambda} amplitudes with the coupling of {phi} to the K components of the final states of these reactions via quantum loops. We obtain good agreement with experiment when the dominant {pi}{sup -}p{yields}K{sup 0}{lambda} amplitude is constrained with its experimental cross section. We also evaluate the coupling of N*(1535) to {phi}N and find a moderate coupling as a consequence of partial cancellation of the large KY components of N*(1535). We also show thatmore » the N*(1535) pole approximation is too small to reproduce the measured cross section for the {pi}{sup -}N{yields}{phi}N reaction.« less

Impacts of pinyon-juniper treatments on water yields: A historical perspective

Treesearch

Peter F. Ffolliott; Cody Stropki

2008-01-01

Pinyon-juniper woodlands are not normally considered a high water-yielding type largely because of the low precipitation amounts and high evapotranspiration rates encountered. Nevertheless, a recommendation was made in the 1950s to evaluate the effectiveness of increasing water yields by converting pinyon-juniper overstories to herbaceous covers. A series of process...

Large scale EMF in current sheets induced by tearing modes

NASA Astrophysics Data System (ADS)

Mizerski, Krzysztof A.

2018-02-01

An extension of the analysis of resistive instabilities of a sheet pinch from a famous work by Furth et al (1963 Phys. Fluids 6 459) is presented here, to study the mean electromotive force (EMF) generated by the developing instability. In a Cartesian configuration and in the presence of a current sheet first the boundary layer technique is used to obtain global, matched asymptotic solutions for the velocity and magnetic field and then the solutions are used to calculate the large-scale EMF in the system. It is reported, that in the bulk the curl of the mean EMF is linear in {{j}}0\\cdot {{B}}0, a simple pseudo-scalar quantity constructed from the large-scale quantities.

Evaluation of agricultural best-management practices in the Conestoga River headwaters, Pennsylvania; effects of pipe-outlet terracing on quantity and quality of surface runoff and ground water in a small carbonate-rock basin near Churchtown, Pennsylvania, 1983-89

USGS Publications Warehouse

Lietman, P.L.; Gustafson-Minnich, L. C.; Hall, D.W.

1997-01-01

soils is believed to have increased nitrate concentrations in runoff. No significant change was found in yields of total nitrogen, ammonia plus organic nitrogen, or total phosphorus relative to runoff before and after terracing. Limited data suggest that fine-sediment particles (less than 0.62 micrometers in diameter), which continued to be discharged from the site, transported most of the phosphorus. Terracing did not significantly change the quantity of recharge to the carbonate aquifer. The mean annual water-table altitude did not change after terracing. Nitrate concentrations of ground water increased significantly at four of the site wells after terracing, probably because of increased contact time of the recharge with nutrient-rich soils in ponded terrace water. Qualitative evidence indicates that large decreases in nutrient requirements and nitrogen applications because of a crop change from corn to alfalfa upgradient of two site wells resulted in either no detectable change or a significant decrease in nitrate concentrations of ground water after terracing.

Infants Make Quantity Discriminations for Substances

ERIC Educational Resources Information Center

Hespos, Susan J.; Dora, Begum; Rips, Lance J.; Christie, Stella

2012-01-01

Infants can track small groups of solid objects, and infants can respond when these quantities change. But earlier work is equivocal about whether infants can track continuous substances, such as piles of sand. Experiment 1 ("N" = 88) used a habituation paradigm to show infants can register changes in the size of piles of sand that they…

Evaluation of Rgb-Based Vegetation Indices from Uav Imagery to Estimate Forage Yield in Grassland

NASA Astrophysics Data System (ADS)

Lussem, U.; Bolten, A.; Gnyp, M. L.; Jasper, J.; Bareth, G.

2018-04-01

Monitoring forage yield throughout the growing season is of key importance to support management decisions on grasslands/pastures. Especially on intensely managed grasslands, where nitrogen fertilizer and/or manure are applied regularly, precision agriculture applications are beneficial to support sustainable, site-specific management decisions on fertilizer treatment, grazing management and yield forecasting to mitigate potential negative impacts. To support these management decisions, timely and accurate information is needed on plant parameters (e.g. forage yield) with a high spatial and temporal resolution. However, in highly heterogeneous plant communities such as grasslands, assessing their in-field variability non-destructively to determine e.g. adequate fertilizer application still remains challenging. Especially biomass/yield estimation, as an important parameter in assessing grassland quality and quantity, is rather laborious. Forage yield (dry or fresh matter) is mostly measured manually with rising plate meters (RPM) or ultrasonic sensors (handheld or mounted on vehicles). Thus the in-field variability cannot be assessed for the entire field or only with potential disturbances. Using unmanned aerial vehicles (UAV) equipped with consumer grade RGB cameras in-field variability can be assessed by computing RGB-based vegetation indices. In this contribution we want to test and evaluate the robustness of RGB-based vegetation indices to estimate dry matter forage yield on a recently established experimental grassland site in Germany. Furthermore, the RGB-based VIs are compared to indices computed from the Yara N-Sensor. The results show a good correlation of forage yield with RGB-based VIs such as the NGRDI with R2 values of 0.62.

Optimizing rice yields while minimizing yield-scaled global warming potential.

PubMed

Pittelkow, Cameron M; Adviento-Borbe, Maria A; van Kessel, Chris; Hill, James E; Linquist, Bruce A

2014-05-01

To meet growing global food demand with limited land and reduced environmental impact, agricultural greenhouse gas (GHG) emissions are increasingly evaluated with respect to crop productivity, i.e., on a yield-scaled as opposed to area basis. Here, we compiled available field data on CH4 and N2 O emissions from rice production systems to test the hypothesis that in response to fertilizer nitrogen (N) addition, yield-scaled global warming potential (GWP) will be minimized at N rates that maximize yields. Within each study, yield N surplus was calculated to estimate deficit or excess N application rates with respect to the optimal N rate (defined as the N rate at which maximum yield was achieved). Relationships between yield N surplus and GHG emissions were assessed using linear and nonlinear mixed-effects models. Results indicate that yields increased in response to increasing N surplus when moving from deficit to optimal N rates. At N rates contributing to a yield N surplus, N2 O and yield-scaled N2 O emissions increased exponentially. In contrast, CH4 emissions were not impacted by N inputs. Accordingly, yield-scaled CH4 emissions decreased with N addition. Overall, yield-scaled GWP was minimized at optimal N rates, decreasing by 21% compared to treatments without N addition. These results are unique compared to aerobic cropping systems in which N2 O emissions are the primary contributor to GWP, meaning yield-scaled GWP may not necessarily decrease for aerobic crops when yields are optimized by N fertilizer addition. Balancing gains in agricultural productivity with climate change concerns, this work supports the concept that high rice yields can be achieved with minimal yield-scaled GWP through optimal N application rates. Moreover, additional improvements in N use efficiency may further reduce yield-scaled GWP, thereby strengthening the economic and environmental sustainability of rice systems. © 2013 John Wiley & Sons Ltd.

Towards large-scale plasma-assisted synthesis of nanowires

NASA Astrophysics Data System (ADS)

Cvelbar, U.

2011-05-01

Large quantities of nanomaterials, e.g. nanowires (NWs), are needed to overcome the high market price of nanomaterials and make nanotechnology widely available for general public use and applications to numerous devices. Therefore, there is an enormous need for new methods or routes for synthesis of those nanostructures. Here plasma technologies for synthesis of NWs, nanotubes, nanoparticles or other nanostructures might play a key role in the near future. This paper presents a three-dimensional problem of large-scale synthesis connected with the time, quantity and quality of nanostructures. Herein, four different plasma methods for NW synthesis are presented in contrast to other methods, e.g. thermal processes, chemical vapour deposition or wet chemical processes. The pros and cons are discussed in detail for the case of two metal oxides: iron oxide and zinc oxide NWs, which are important for many applications.

Quantity and unit extraction for scientific and technical intelligence analysis

NASA Astrophysics Data System (ADS)

David, Peter; Hawes, Timothy

2017-05-01

Scientific and Technical (S and T) intelligence analysts consume huge amounts of data to understand how scientific progress and engineering efforts affect current and future military capabilities. One of the most important types of information S and T analysts exploit is the quantities discussed in their source material. Frequencies, ranges, size, weight, power, and numerous other properties and measurements describing the performance characteristics of systems and the engineering constraints that define them must be culled from source documents before quantified analysis can begin. Automating the process of finding and extracting the relevant quantities from a wide range of S and T documents is difficult because information about quantities and their units is often contained in unstructured text with ad hoc conventions used to convey their meaning. Currently, even simple tasks, such as searching for documents discussing RF frequencies in a band of interest, is a labor intensive and error prone process. This research addresses the challenges facing development of a document processing capability that extracts quantities and units from S and T data, and how Natural Language Processing algorithms can be used to overcome these challenges.

The Supply of Prescription Opioids: Contributions of Episodic-Care Prescribers and High-Quantity Prescribers.

PubMed

Schneberk, Todd; Raffetto, Brian; Kim, David; Schriger, David L

2018-06-01

We determine episodic and high-quantity prescribers' contribution to opioid prescriptions and total morphine milligram equivalents in California, especially among individuals prescribed large amounts of opioids. This was a cross-sectional descriptive analysis of opioid prescribing patterns during an 8-year period using the de-identified Controlled Substance Utilization Review and Evaluation System (CURES) database, the California subsection of the prescription drug monitoring program. We took a 10% random sample of all patients and stratified them by the amount of prescription opioids obtained during their maximal 90-day period. We identified "episodic prescribers" as those whose prescribing pattern included short-acting opioids on greater than 95% of all prescriptions, fewer than or equal to 31 pills on 95% of all prescriptions, only 1 prescription in the database for greater than 90% of all patients to whom they gave opioids, fewer than 6 prescriptions in the database to greater than 99% of patients given opioids, and fewer than 540 prescriptions per year. We identified top 5% prescribers by their morphine milligram equivalents per day in the database. We examined the relationship between patient opioid prescriptions and provider type, with the primary analysis performed on the patient cohort who received only short-acting opioids in an attempt to avoid guideline-concordant palliative, oncologic, and addiction care, and a secondary analysis performed on all patients. Among patients with short-acting opioid only, episodic prescribers (14.6% of 173,000 prescribers) wrote at least one prescription to 25% of 2.7 million individuals but were responsible for less than 9% of the 10.5 million opioid prescriptions and less than 3% of the 3.9 billion morphine milligram equivalents in our sample. Among individuals with high morphine milligram equivalents use, episodic prescribers were responsible for 2.8% of prescriptions and 0.6% of total morphine milligram equivalents

Genotypic Variation in Yield, Yield Components, Root Morphology and Architecture, in Soybean in Relation to Water and Phosphorus Supply

PubMed Central

He, Jin; Jin, Yi; Du, Yan-Lei; Wang, Tao; Turner, Neil C.; Yang, Ru-Ping; Siddique, Kadambot H. M.; Li, Feng-Min

2017-01-01

Water shortage and low phosphorus (P) availability limit yields in soybean. Roots play important roles in water-limited and P-deficient environment, but the underlying mechanisms are largely unknown. In this study we determined the responses of four soybean [Glycine max (L.) Merr.] genotypes [Huandsedadou (HD), Bailudou (BLD), Jindou 21 (J21), and Zhonghuang 30 (ZH)] to three P levels [applied 0 (P0), 60 (P60), and 120 (P120) mg P kg-1 dry soil to the upper 0.4 m of the soil profile] and two water treatment [well-watered (WW) and water-stressed (WS)] with special reference to root morphology and architecture, we compared yield and its components, root morphology and root architecture to find out which variety and/or what kind of root architecture had high grain yield under P and drought stress. The results showed that water stress and low P, respectively, significantly reduced grain yield by 60 and 40%, daily water use by 66 and 31%, P accumulation by 40 and 80%, and N accumulation by 39 and 65%. The cultivar ZH with the lowest daily water use had the highest grain yield at P60 and P120 under drought. Increased root length was positively associated with N and P accumulation in both the WW and WS treatments, but not with grain yield under water and P deficits. However, in the WS treatment, high adventitious and lateral root densities were associated with high N and P uptake per unit root length which in turn was significantly and positively associated with grain yield. Our results suggest that (1) genetic variation of grain yield, daily water use, P and N accumulation, and root morphology and architecture were observed among the soybean cultivars and ZH had the best yield performance under P and water limited conditions; (2) water has a major influence on nutrient uptake and grain yield, while additional P supply can modestly increase yields under drought in some soybean genotypes; (3) while conserved water use plays an important role in grain yield under drought

Genotypic Variation in Yield, Yield Components, Root Morphology and Architecture, in Soybean in Relation to Water and Phosphorus Supply.

PubMed

He, Jin; Jin, Yi; Du, Yan-Lei; Wang, Tao; Turner, Neil C; Yang, Ru-Ping; Siddique, Kadambot H M; Li, Feng-Min

2017-01-01

Water shortage and low phosphorus (P) availability limit yields in soybean. Roots play important roles in water-limited and P-deficient environment, but the underlying mechanisms are largely unknown. In this study we determined the responses of four soybean [ Glycine max (L.) Merr.] genotypes [Huandsedadou (HD), Bailudou (BLD), Jindou 21 (J21), and Zhonghuang 30 (ZH)] to three P levels [applied 0 (P0), 60 (P60), and 120 (P120) mg P kg -1 dry soil to the upper 0.4 m of the soil profile] and two water treatment [well-watered (WW) and water-stressed (WS)] with special reference to root morphology and architecture, we compared yield and its components, root morphology and root architecture to find out which variety and/or what kind of root architecture had high grain yield under P and drought stress. The results showed that water stress and low P, respectively, significantly reduced grain yield by 60 and 40%, daily water use by 66 and 31%, P accumulation by 40 and 80%, and N accumulation by 39 and 65%. The cultivar ZH with the lowest daily water use had the highest grain yield at P60 and P120 under drought. Increased root length was positively associated with N and P accumulation in both the WW and WS treatments, but not with grain yield under water and P deficits. However, in the WS treatment, high adventitious and lateral root densities were associated with high N and P uptake per unit root length which in turn was significantly and positively associated with grain yield. Our results suggest that (1) genetic variation of grain yield, daily water use, P and N accumulation, and root morphology and architecture were observed among the soybean cultivars and ZH had the best yield performance under P and water limited conditions; (2) water has a major influence on nutrient uptake and grain yield, while additional P supply can modestly increase yields under drought in some soybean genotypes; (3) while conserved water use plays an important role in grain yield under drought

Lacking control over the trade-off between quality and quantity in visual short-term memory.

PubMed

Murray, Alexandra M; Nobre, Anna C; Astle, Duncan E; Stokes, Mark G

2012-01-01

Visual short-term memory (VSTM) is limited in the quantity and quality of items that can be retained over time. Importantly, these two mnemonic parameters interact: increasing the number of items in VSTM reduces the quality with which they are represented. Here, we ask whether this trade-off is under top-down control. Specifically, we test whether participants can strategically optimise the trade-off between quality and quantity for VSTM according to task demands. We manipulated strategic trade-off by varying expectations about the number of to-be-remembered items (Experiments 1-2) or the precision required for the memory-based judgement (Experiment 3). In a final experiment, we manipulated both variables in a complementary way to maximise the motivation to strategically control the balance between number and the quality of items encoded into VSTM. In different blocks, performance would benefit most either by encoding a large number of items with low precision or by encoding a small number of items with high precision (Experiment 4). In all experiments, we compared VSTM performance on trials matched for mnemonic demand, but within contexts emphasising the quality or quantity of VSTM representations. Across all four experiments, we found no evidence to suggest that participants use this contextual information to bias the balance between the number and precision of items in VSTM. Rather, our data suggest that the trade-off may be determined primarily by stimulus-driven factors at encoding.

Methodology for assessing quantities of water and proppant injection, and water production associated with development of continuous petroleum accumulations

USGS Publications Warehouse

Haines, Seth S.

2015-07-13

The quantities of water and hydraulic fracturing proppant required for producing petroleum (oil, gas, and natural gas liquids) from continuous accumulations, and the quantities of water extracted during petroleum production, can be quantitatively assessed using a probabilistic approach. The water and proppant assessment methodology builds on the U.S. Geological Survey methodology for quantitative assessment of undiscovered technically recoverable petroleum resources in continuous accumulations. The U.S. Geological Survey assessment methodology for continuous petroleum accumulations includes fundamental concepts such as geologically defined assessment units, and probabilistic input values including well-drainage area, sweet- and non-sweet-spot areas, and success ratio within the untested area of each assessment unit. In addition to petroleum-related information, required inputs for the water and proppant assessment methodology include probabilistic estimates of per-well water usage for drilling, cementing, and hydraulic-fracture stimulation; the ratio of proppant to water for hydraulic fracturing; the percentage of hydraulic fracturing water that returns to the surface as flowback; and the ratio of produced water to petroleum over the productive life of each well. Water and proppant assessments combine information from recent or current petroleum assessments with water- and proppant-related input values for the assessment unit being studied, using Monte Carlo simulation, to yield probabilistic estimates of the volume of water for drilling, cementing, and hydraulic fracture stimulation; the quantity of proppant for hydraulic fracture stimulation; and the volumes of water produced as flowback shortly after well completion, and produced over the life of the well.

Efficient SRAM yield optimization with mixture surrogate modeling

NASA Astrophysics Data System (ADS)

Zhongjian, Jiang; Zuochang, Ye; Yan, Wang

2016-12-01

Largely repeated cells such as SRAM cells usually require extremely low failure-rate to ensure a moderate chi yield. Though fast Monte Carlo methods such as importance sampling and its variants can be used for yield estimation, they are still very expensive if one needs to perform optimization based on such estimations. Typically the process of yield calculation requires a lot of SPICE simulation. The circuit SPICE simulation analysis accounted for the largest proportion of time in the process yield calculation. In the paper, a new method is proposed to address this issue. The key idea is to establish an efficient mixture surrogate model. The surrogate model is based on the design variables and process variables. This model construction method is based on the SPICE simulation to get a certain amount of sample points, these points are trained for mixture surrogate model by the lasso algorithm. Experimental results show that the proposed model is able to calculate accurate yield successfully and it brings significant speed ups to the calculation of failure rate. Based on the model, we made a further accelerated algorithm to further enhance the speed of the yield calculation. It is suitable for high-dimensional process variables and multi-performance applications.

30 CFR 1206.119 - How are royalty quantity and quality determined?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

30 CFR 1206.119 - How are royalty quantity and quality determined?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

30 CFR 1206.119 - How are royalty quantity and quality determined?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false How are royalty quantity and quality determined? 1206.119 Section 1206.119 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Oil § 1206.119 How are royalty quantity and...

[Contrast of Z-Pinch X-Ray Yield Measure Technique].

PubMed

Li, Mo; Wang, Liang-ping; Sheng, Liang; Lu, Yi

2015-03-01

Resistive bolometer and scintillant detection system are two mainly Z-pinch X-ray yield measure techniques which are based on different diagnostic principles. Contrasting the results from two methods can help with increasing precision of X-ray yield measurement. Experiments with different load material and shape were carried out on the "QiangGuang-I" facility. For Al wire arrays, X-ray yields measured by the two techniques were largely consistent. However, for insulating coating W wire arrays, X-ray yields taken from bolometer changed with load parameters while data from scintillant detection system hardly changed. Simulation and analysis draw conclusions as follows: (1) Scintillant detection system is much more sensitive to X-ray photons with low energy and its spectral response is wider than the resistive bolometer. Thus, results from the former method are always larger than the latter. (2) The responses of the two systems are both flat to Al plasma radiation. Thus, their results are consistent for Al wire array loads. (3) Radiation form planar W wire arrays is mainly composed of sub-keV soft X-ray. X-ray yields measured by the bolometer is supposed to be accurate because of the nickel foil can absorb almost all the soft X-ray. (4) By contrast, using planar W wire arrays, data from scintillant detection system hardly change with load parameters. A possible explanation is that while the distance between wires increases, plasma temperature at stagnation reduces and spectra moves toward the soft X-ray region. Scintillator is much more sensitive to the soft X-ray below 200 eV. Thus, although the total X-ray yield reduces with large diameter load, signal from the scintillant detection system is almost the same. (5) Both Techniques affected by electron beams produced by the loads.

Machine Learning and Deep Learning Models to Predict Runoff Water Quantity and Quality

NASA Astrophysics Data System (ADS)

Bradford, S. A.; Liang, J.; Li, W.; Murata, T.; Simunek, J.

2017-12-01

Contaminants can be rapidly transported at the soil surface by runoff to surface water bodies. Physically-based models, which are based on the mathematical description of main hydrological processes, are key tools for predicting surface water impairment. Along with physically-based models, data-driven models are becoming increasingly popular for describing the behavior of hydrological and water resources systems since these models can be used to complement or even replace physically based-models. In this presentation we propose a new data-driven model as an alternative to a physically-based overland flow and transport model. First, we have developed a physically-based numerical model to simulate overland flow and contaminant transport (the HYDRUS-1D overland flow module). A large number of numerical simulations were carried out to develop a database containing information about the impact of various input parameters (weather patterns, surface topography, vegetation, soil conditions, contaminants, and best management practices) on runoff water quantity and quality outputs. This database was used to train data-driven models. Three different methods (Neural Networks, Support Vector Machines, and Recurrence Neural Networks) were explored to prepare input- output functional relations. Results demonstrate the ability and limitations of machine learning and deep learning models to predict runoff water quantity and quality.

Quantity judgments of sequentially presented food items by capuchin monkeys (Cebus apella).

PubMed

Evans, Theodore A; Beran, Michael J; Harris, Emily H; Rice, Daniel F

2009-01-01

Recent assessments have shown that capuchin monkeys, like chimpanzees and other Old World primate species, are sensitive to quantitative differences between sets of visible stimuli. In the present study, we examined capuchins' performance in a more sophisticated quantity judgment task that required the ability to form representations of food quantities while viewing the quantities only one piece at a time. In three experiments, we presented monkeys with the choice between two sets of discrete homogeneous food items and allowed the monkeys to consume the set of their choice. In Experiments 1 and 2, monkeys compared an entirely visible food set to a second set, presented item-by-item into an opaque container. All monkeys exhibited high accuracy in choosing the larger set, even when the entirely visible set was presented last, preventing the use of one-to-one item correspondence to compare quantities. In Experiment 3, monkeys compared two sets that were each presented item-by-item into opaque containers, but at different rates to control for temporal cues. Some monkeys performed well in this experiment, though others exhibited near-chance performance, suggesting that this species' ability to form representations of food quantities may be limited compared to previously tested species such as chimpanzees. Overall, these findings support the analog magnitude model of quantity representation as an explanation for capuchin monkeys' quantification of sequentially presented food items.

[Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

PubMed

Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

2011-12-01

To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

Hot spots of wheat yield decline with rising temperatures.

PubMed

Asseng, Senthold; Cammarano, Davide; Basso, Bruno; Chung, Uran; Alderman, Phillip D; Sonder, Kai; Reynolds, Matthew; Lobell, David B

2017-06-01

Many of the irrigated spring wheat regions in the world are also regions with high poverty. The impacts of temperature increase on wheat yield in regions of high poverty are uncertain. A grain yield-temperature response function combined with a quantification of model uncertainty was constructed using a multimodel ensemble from two key irrigated spring wheat areas (India and Sudan) and applied to all irrigated spring wheat regions in the world. Southern Indian and southern Pakistani wheat-growing regions with large yield reductions from increasing temperatures coincided with high poverty headcounts, indicating these areas as future food security 'hot spots'. The multimodel simulations produced a linear absolute decline of yields with increasing temperature, with uncertainty varying with reference temperature at a location. As a consequence of the linear absolute yield decline, the relative yield reductions are larger in low-yielding environments (e.g., high reference temperature areas in southern India, southern Pakistan and all Sudan wheat-growing regions) and farmers in these regions will be hit hardest by increasing temperatures. However, as absolute yield declines are about the same in low- and high-yielding regions, the contributed deficit to national production caused by increasing temperatures is higher in high-yielding environments (e.g., northern India) because these environments contribute more to national wheat production. Although Sudan could potentially grow more wheat if irrigation is available, grain yields would be low due to high reference temperatures, with future increases in temperature further limiting production. © 2016 John Wiley & Sons Ltd.

The Role of Climate Covariability on Crop Yields in the Conterminous United States

DOE PAGES

Leng, Guoyong; Zhang, Xuesong; Huang, Maoyi; ...

2016-09-12

The covariability of temperature (T), precipitation (P) and radiation (R) is an important aspect in understanding the climate influence on crop yields. Here in this paper, we analyze county-level corn and soybean yields and observed climate for the period 1983–2012 to understand how growing-season (June, July and August) mean T, P and R influence crop yields jointly and in isolation across the CONterminous United States (CONUS). Results show that nationally averaged corn and soybean yields exhibit large interannual variability of 21% and 22%, of which 35% and 32% can be significantly explained by T and P, respectively. By including R,more » an additional of 5% in variability can be explained for both crops. Using partial regression analyses, we find that studies that ignore the covariability among T, P, and R can substantially overestimate the sensitivity of crop yields to a single climate factor at the county scale. Further analyses indicate large spatial variation in the relative contributions of different climate variables to the variability of historical corn and soybean yields. Finally, the structure of the dominant climate factors did not change substantially over 1983–2012, confirming the robustness of the findings, which have important implications for crop yield prediction and crop model validations.« less

30 CFR 250.458 - What quantities of drilling fluids are required?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

30 CFR 250.458 - What quantities of drilling fluids are required?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What quantities of drilling fluids are required...

30 CFR 250.458 - What quantities of drilling fluids are required?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

30 CFR 250.458 - What quantities of drilling fluids are required?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false What quantities of drilling fluids are required... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are...

Estimation of Rice Crop Yields Using Random Forests in Taiwan

NASA Astrophysics Data System (ADS)

Chen, C. F.; Lin, H. S.; Nguyen, S. T.; Chen, C. R.

2017-12-01

Rice is globally one of the most important food crops, directly feeding more people than any other crops. Rice is not only the most important commodity, but also plays a critical role in the economy of Taiwan because it provides employment and income for large rural populations. The rice harvested area and production are thus monitored yearly due to the government's initiatives. Agronomic planners need such information for more precise assessment of food production to tackle issues of national food security and policymaking. This study aimed to develop a machine-learning approach using physical parameters to estimate rice crop yields in Taiwan. We processed the data for 2014 cropping seasons, following three main steps: (1) data pre-processing to construct input layers, including soil types and weather parameters (e.g., maxima and minima air temperature, precipitation, and solar radiation) obtained from meteorological stations across the country; (2) crop yield estimation using the random forests owing to its merits as it can process thousands of variables, estimate missing data, maintain the accuracy level when a large proportion of the data is missing, overcome most of over-fitting problems, and run fast and efficiently when handling large datasets; and (3) error verification. To execute the model, we separated the datasets into two groups of pixels: group-1 (70% of pixels) for training the model and group-2 (30% of pixels) for testing the model. Once the model is trained to produce small and stable out-of-bag error (i.e., the mean squared error between predicted and actual values), it can be used for estimating rice yields of cropping seasons. The results obtained from the random forests-based regression were compared with the actual yield statistics indicated the values of root mean square error (RMSE) and mean absolute error (MAE) achieved for the first rice crop were respectively 6.2% and 2.7%, while those for the second rice crop were 5.3% and 2

Quantity and quality of streamflow in the White River basin, Colorado and Utah

USGS Publications Warehouse

Boyle, J.M.; Covay, K.J.; Bauer, D.P.

1984-01-01

The water quality and flow of existing streams in the White River basin, located in northwestern Colorado and northeastern Utah, are adequate for present uses, but future development (such as energy) may affect stream quality and quantity. Present conditions are described as a baseline to enable planners to allocate available water and to measure changes in quantity and quality of water in the future. The White River basin contains extensive energy resources consisting of oil, natural gas, coal, and oil shale. Large quantities of water will be required for energy-resource development and associated municipal and industrial uses. An average of 70% of the annual flow in the White River occurs during May, June, and July as a result of snowmelt runoff. The 7-day, 10-year low-flow discharges/sq mi and the 1-day, 25-year high-flow discharges/sq mi are larger in the eastern part of the basin than in the western part. Flow-duration curves indicate that high flows in the White River and the North and South Fork White Rivers result mainly from snowmelt runoff and that base flow is sustained throughout the year by groundwater discharge from the alluvial and bedrock aquifers. Water type varies in the basin; however, calcium and sodium are the dominantly occurring cations and sulfate and bicarbonate are the dominantly occurring anions. Computed total annual dissolved-solids loads in the White River range from 31 ,800 tons/yr in the North Fork White River to 284,000 tons/yr at the mouth. A 10% increase to a 14% decrease of the dissolved-solids load could result at the mouth of the White River near Ouray, Utah. This corresponds to a 5% increase to a 10% decrease in dissolved-solids concentration. The seasonal pattern of stream temperatures was found to fit a harmonic curve. (Lantz-PTT)

Stocking, growth, and yield of birch stands

Treesearch

Dale S. Solomon; William B. Leak

1969-01-01

Intensive forest management depends heavily upon our ability to measure, control, and predict the growth, yield, or general development of timber stands, regardless of whether the management goal is for timber, aesthetics, recreation, water, or wildlife. A large amount of mensurational data about birch stands has been developed in recent years or synthesized from...

Exercise quantity-dependent muscle hypertrophy in adult zebrafish (Danio rerio).

PubMed

Hasumura, Takahiro; Meguro, Shinichi

2016-07-01

Exercise is very important for maintaining and increasing skeletal muscle mass, and is particularly important to prevent and care for sarcopenia and muscle disuse atrophy. However, the dose-response relationship between exercise quantity, duration/day, and overall duration and muscle mass is poorly understood. Therefore, we investigated the effect of exercise duration on skeletal muscle to reveal the relationship between exercise quantity and muscle hypertrophy in zebrafish forced to exercise. Adult male zebrafish were exercised 6 h/day for 4 weeks, 6 h/day for 2 weeks, or 3 h/day for 2 weeks. Flow velocity was adjusted to maximum velocity during continual swimming (initial 43 cm/s). High-speed consecutive photographs revealed that zebrafish mainly drove the caudal part. Additionally, X-ray micro computed tomography measurements indicated muscle hypertrophy of the mid-caudal half compared with the mid-cranial half part. The cross-sectional analysis of the mid-caudal half muscle revealed that skeletal muscle (red, white, or total) mass increased with increasing exercise quantity, whereas that of white muscle and total muscle increased only under the maximum exercise load condition of 6 h/day for 4 weeks. Additionally, the muscle fiver size distributions of exercised fish were larger than those from non-exercised fish. We revealed that exercise quantity, duration/day, and overall duration were correlated with skeletal muscle hypertrophy. The forced exercise model enabled us to investigate the relationship between exercise quantity and skeletal muscle mass. These results open up the possibility for further investigations on the effects of exercise on skeletal muscle in adult zebrafish.

48 CFR 816.504 - Indefinite-quantity contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Indefinite-quantity contracts. 816.504 Section 816.504 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS....216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

48 CFR 816.504 - Indefinite-quantity contracts.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Indefinite-quantity contracts. 816.504 Section 816.504 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS....216-70 in solicitations for bulk coal. (c) The contracting officer shall insert the Alternate II...

Linear actuation using milligram quantities of CL-20 and TAGDNAT.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snedigar, Shane; Salton, Jonathan Robert; Tappan, Alexander Smith

2009-07-01

There are numerous applications for small-scale actuation utilizing pyrotechnics and explosives. In certain applications, especially when multiple actuation strokes are needed, or actuator reuse is required, it is desirable to have all gaseous combustion products with no condensed residue in the actuator cylinder. Toward this goal, we have performed experiments on utilizing milligram quantities of high explosives to drive a millimeter-diameter actuator with a stroke of 30 mm. Calculations were performed to select proper material quantities to provide 0.5 J of actuation energy. This was performed utilizing the thermochemical code Cheetah to calculate the impetus for numerous propellants and tomore » select quantities based on estimated efficiencies of these propellants at small scales. Milligram quantities of propellants were loaded into a small-scale actuator and ignited with an ignition increment and hot wire ignition. Actuator combustion chamber pressure was monitored with a pressure transducer and actuator stroke was monitored using a laser displacement meter. Total actuation energy was determined by calculating the kinetic energy of reaction mass motion against gravity. Of the materials utilized, the best performance was obtained with a mixture of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and bis-triaminoguanidinium(3,3{prime}dinitroazotriazolate) (TAGDNAT).« less

30 CFR 250.458 - What quantities of drilling fluids are required?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.458 What quantities of drilling fluids are required? (a) You must use... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What quantities of drilling fluids are required...

78 FR 5448 - Federal Acquisition Regulation; Submission for OMB Review; Economic Purchase Quantity-Supplies

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-25

...; Submission for OMB Review; Economic Purchase Quantity--Supplies AGENCY: Department of Defense (DOD), General... collection requirement concerning Economic Purchase Quantity--Supplies. A notice was published in the Federal... Information Collection 9000- 0082, Economic Purchase Quantity--Supplies, by any of the following methods...

Yield and yield gaps in central U.S. corn production systems

USDA-ARS?s Scientific Manuscript database

The magnitude of yield gaps (YG) (potential yield – farmer yield) provides some indication of the prospects for increasing crop yield. Quantile regression analysis was applied to county maize (Zea mays L.) yields (1972 – 2011) from Kentucky, Iowa and Nebraska (irrigated) (total of 115 counties) to e...

46 CFR 76.15-5 - Quantity, pipe sizes, and discharge rate.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 3 2011-10-01 2011-10-01 false Quantity, pipe sizes, and discharge rate. 76.15-5... PROTECTION EQUIPMENT Carbon Dioxide Extinguishing Systems, Details § 76.15-5 Quantity, pipe sizes, and... dioxide required for each space in cubic feet shall be equal to the gross volume of the space in cubic...

46 CFR 34.17-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

46 CFR 34.17-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

46 CFR 34.17-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

46 CFR 34.17-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

46 CFR 34.17-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Quantity of foam required-T/ALL. 34.17-5 Section 34.17-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Fixed Foam Extinguishing Systems, Details § 34.17-5 Quantity of foam required—T/ALL. (a) Area protected. (1) For machinery...

Categories of Large Numbers in Line Estimation

ERIC Educational Resources Information Center

Landy, David; Charlesworth, Arthur; Ottmar, Erin

2017-01-01

How do people stretch their understanding of magnitude from the experiential range to the very large quantities and ranges important in science, geopolitics, and mathematics? This paper empirically evaluates how and whether people make use of numerical categories when estimating relative magnitudes of numbers across many orders of magnitude. We…

Observable quantities for electrodiffusion processes in membranes.

PubMed

Garrido, Javier

2008-03-13

Electrically driven ion transport processes in a membrane system are analyzed in terms of observable quantities, such as the apparent volume flow, the time dependence of the electrolyte concentration in one cell compartment, and the electrical potential difference between the electrodes. The relations between the fluxes and these observable quantities are rigorously deduced from balances for constituent mass and solution volume. These relations improve the results for the transport coefficients up to 25% with respect to those obtained using simplified expressions common in the literature. Given the practical importance of ionic transport numbers and the solvent transference number in the phenomenological description of electrically driven processes, the transport equations are presented using the electrolyte concentration difference and the electric current as the drivers of the different constituents. Because various electric potential differences can be used in this traditional irreversible thermodynamics approach, the advantages of the formulation of the transport equations in terms of concentration difference and electric current are emphasized.

Growth and Yield of Thinned Yellow-Poplar

Treesearch

Donald E. Beck; Lino Della-Bianca

1972-01-01

Diameter distributions and yields for various combinations of site index, age, and density for unthinned and largely undisturbed stands of yellow-poplar (Liriodendron tulipifera L. ) have been presented by McGee and Della-Bianca (1967) and Beck and Della-Bianca (1970). Their results were based on the initial measurements of a network of permanent sample plots...

Giant intracranial aneurysm embolization with a yield stress fluid material: insights from CFD analysis.

PubMed

Wang, Weixiong; Graziano, Francesca; Russo, Vittorio; Ulm, Arthur J; De Kee, Daniel; Khismatullin, Damir B

2013-01-01

The endovascular treatment of intracranial aneurysms remains a challenge, especially when the aneurysm is large in size and has irregular, non-spherical geometry. In this paper, we use computational fluid dynamics to simulate blood flow in a vertebro-basilar junction giant aneurysm for the following three cases: (1) an empty aneurysm, (2) an aneurysm filled with platinum coils, and (3) an aneurysm filled with a yield stress fluid material. In the computational model, blood and the coil-filled region are treated as a non-Newtonian fluid and an isotropic porous medium, respectively. The results show that yield stress fluids can be used for aneurysm embolization provided the yield stress value is 20 Pa or higher. Specifically, flow recirculation in the aneurysm and the size of the inflow jet impingement zone on the aneurysm wall are substantially reduced by yield stress fluid treatment. Overall, this study opens up the possibility of using yield stress fluids for effective embolization of large-volume intracranial aneurysms.

High Purity and Yield of Boron Nitride Nanotubes Using Amorphous Boron and a Nozzle-Type Reactor

PubMed Central

Kim, Jaewoo; Seo, Duckbong; Yoo, Jeseung; Jeong, Wanseop; Seo, Young-Soo; Kim, Jaeyong

2014-01-01

Enhancement of the production yield of boron nitride nanotubes (BNNTs) with high purity was achieved using an amorphous boron-based precursor and a nozzle-type reactor. Use of a mixture of amorphous boron and Fe decreases the milling time for the preparation of the precursor for BNNTs synthesis, as well as the Fe impurity contained in the B/Fe interdiffused precursor nanoparticles by using a simple purification process. We also explored a nozzle-type reactor that increased the production yield of BNNTs compared to a conventional flow-through reactor. By using a nozzle-type reactor with amorphous boron-based precursor, the weight of the BNNTs sample after annealing was increased as much as 2.5-times with much less impurities compared to the case for the flow-through reactor with the crystalline boron-based precursor. Under the same experimental conditions, the yield and quantity of BNNTs were estimated as much as ~70% and ~1.15 g/batch for the former, while they are ~54% and 0.78 g/batch for the latter. PMID:28788161

High Purity and Yield of Boron Nitride Nanotubes Using Amorphous Boron and a Nozzle-Type Reactor.

PubMed

Kim, Jaewoo; Seo, Duckbong; Yoo, Jeseung; Jeong, Wanseop; Seo, Young-Soo; Kim, Jaeyong

2014-08-11

Enhancement of the production yield of boron nitride nanotubes (BNNTs) with high purity was achieved using an amorphous boron-based precursor and a nozzle-type reactor. Use of a mixture of amorphous boron and Fe decreases the milling time for the preparation of the precursor for BNNTs synthesis, as well as the Fe impurity contained in the B/Fe interdiffused precursor nanoparticles by using a simple purification process. We also explored a nozzle-type reactor that increased the production yield of BNNTs compared to a conventional flow-through reactor. By using a nozzle-type reactor with amorphous boron-based precursor, the weight of the BNNTs sample after annealing was increased as much as 2.5-times with much less impurities compared to the case for the flow-through reactor with the crystalline boron-based precursor. Under the same experimental conditions, the yield and quantity of BNNTs were estimated as much as ~70% and ~1.15 g/batch for the former, while they are ~54% and 0.78 g/batch for the latter.

High quantum yield ZnO quantum dots synthesizing via an ultrasonication microreactor method.

PubMed

Yang, Weimin; Yang, Huafang; Ding, Wenhao; Zhang, Bing; Zhang, Le; Wang, Lixi; Yu, Mingxun; Zhang, Qitu

2016-11-01

Green emission ZnO quantum dots were synthesized by an ultrasonic microreactor. Ultrasonic radiation brought bubbles through ultrasonic cavitation. These bubbles built microreactor inside the microreactor. The photoluminescence properties of ZnO quantum dots synthesized with different flow rate, ultrasonic power and temperature were discussed. Flow rate, ultrasonic power and temperature would influence the type and quantity of defects in ZnO quantum dots. The sizes of ZnO quantum dots would be controlled by those conditions as well. Flow rate affected the reaction time. With the increasing of flow rate, the sizes of ZnO quantum dots decreased and the quantum yields first increased then decreased. Ultrasonic power changed the ultrasonic cavitation intensity, which affected the reaction energy and the separation of the solution. With the increasing of ultrasonic power, sizes of ZnO quantum dots first decreased then increased, while the quantum yields kept increasing. The effect of ultrasonic temperature on the photoluminescence properties of ZnO quantum dots was influenced by the flow rate. Different flow rate related to opposite changing trend. Moreover, the quantum yields of ZnO QDs synthesized by ultrasonic microreactor could reach 64.7%, which is higher than those synthesized only under ultrasonic radiation or only by microreactor. Copyright © 2016 Elsevier B.V. All rights reserved.

Self-Monitoring of Blood Glucose: Impact of Quantity Limits in Public Drug Formularies on Provincial Costs Across Canada.

PubMed

Knowles, Sandra R; Lee, Kathy; Paterson, J Michael; Shah, Baiju R; Mamdani, Muhammad M; Juurlink, David N; Gomes, Tara

2017-04-01

For most patients with diabetes, routine use of blood glucose test strips (BGTS) has not been shown to be beneficial, yet the economic implications of broad publicly funded reimbursement for BGTS are substantial. We assessed the potential impact of BGTS quantity limits on utilization and costs for 6 publicly funded drug plans across Canada. A cross-sectional analysis was conducted in 6 provinces (Alberta, Saskatchewan, Manitoba, Nova Scotia, Newfoundland and Labrador and Prince Edward Island) for patients who received at least 1 prescription for BGTS in 2014 through the public drug program. We determined the number of BGTS that would have exceeded the quantity limits and the associated costs to the provincial drug program. A total of $38,051,026 was spent on BGTS reimbursed through public drug programs among the 6 provinces. In provinces where BGTS use is largely restricted to patients using insulin, the potential annual savings were minimal, ranging from 0.4% to 2.3%, whereas in provinces with more liberal listings, potential savings ranged from 12.4% to 19.8%. Combining these results with data from a previous analysis in Ontario and British Columbia, the cost savings associated with BGTS quantity limits for 8 provinces across Canada (capturing approximately three-quarters of the Canadian population) is estimated to be $30.3 million annually. The national implementation of a quantity limit policy for BGTS that aligns with evidence of efficacy, optimal prescribing and patient safety can lead to considerable savings for most public drug plans across Canada. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Improved sugar yields from biomass sorghum feedstocks: comparing low-lignin mutants and pretreatment chemistries.

PubMed

Godin, Bruno; Nagle, Nick; Sattler, Scott; Agneessens, Richard; Delcarte, Jérôme; Wolfrum, Edward

2016-01-01

For biofuel production processes to be economically efficient, it is essential to maximize the production of monomeric carbohydrates from the structural carbohydrates of feedstocks. One strategy for maximizing carbohydrate production is to identify less recalcitrant feedstock cultivars by performing some type of experimental screening on a large and diverse set of candidate materials, or by identifying genetic modifications (random or directed mutations or transgenic plants) that provide decreased recalcitrance. Economic efficiency can also be increased using additional pretreatment processes such as deacetylation, which uses dilute NaOH to remove the acetyl groups of hemicellulose prior to dilute acid pretreatment. In this work, we used a laboratory-scale screening tool that mimics relevant thermochemical pretreatment conditions to compare the total sugar yield of three near-isogenic brown midrib ( bmr ) mutant lines and the wild-type (WT) sorghum cultivar. We then compared results obtained from the laboratory-scale screening pretreatment assay to a large-scale pretreatment system. After pretreatment and enzymatic hydrolysis, the bmr mutants had higher total sugar yields than the WT sorghum cultivar. Increased pretreatment temperatures increased reactivity for all sorghum samples reducing the differences observed at lower reaction temperatures. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples, and reduced the differences in total sugar yields among them, but solubilized a sizable fraction of the non-structural carbohydrates. The general trends of increased total sugar yield in the bmr mutant compared to the WT seen at the laboratory scale were observed at the large-scale system. However, in the larger reactor system, the measured total sugar yields were lower and the difference in total sugar yield between the WT and bmr sorghum was larger. Sorghum bmr mutants, which have a reduced lignin content showed

Improved sugar yields from biomass sorghum feedstocks: comparing low-lignin mutants and pretreatment chemistries

DOE PAGES

Godin, Bruno; Nagle, Nick; Sattler, Scott; ...

2016-11-21

For biofuel production processes to be economically efficient, it is essential to maximize the production of monomeric carbohydrates from the structural carbohydrates of feedstocks. One strategy for maximizing carbohydrate production is to identify less recalcitrant feedstock cultivars by performing some type of experimental screening on a large and diverse set of candidate materials, or by identifying genetic modifications (random or directed mutations or transgenic plants) that provide decreased recalcitrance. Economic efficiency can also be increased using additional pretreatment processes such as deacetylation, which uses dilute NaOH to remove the acetyl groups of hemicellulose prior to dilute acid pretreatment. In thismore » work, we used a laboratory-scale screening tool that mimics relevant thermochemical pretreatment conditions to compare the total sugar yield of three near-isogenic brown midrib (bmr) mutant lines and the wild-type (WT) sorghum cultivar. We then compared results obtained from the laboratory-scale screening pretreatment assay to a large-scale pretreatment system. After pretreatment and enzymatic hydrolysis, the bmr mutants had higher total sugar yields than the WT sorghum cultivar. Increased pretreatment temperatures increased reactivity for all sorghum samples reducing the differences observed at lower reaction temperatures. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples, and reduced the differences in total sugar yields among them, but solubilized a sizable fraction of the non-structural carbohydrates. The general trends of increased total sugar yield in the bmr mutant compared to the WT seen at the laboratory scale were observed at the large-scale system. However, in the larger reactor system, the measured total sugar yields were lower and the difference in total sugar yield between the WT and bmr sorghum was larger. Sorghum bmr mutants, which have a reduced lignin content

Improved sugar yields from biomass sorghum feedstocks: comparing low-lignin mutants and pretreatment chemistries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Godin, Bruno; Nagle, Nick; Sattler, Scott

For biofuel production processes to be economically efficient, it is essential to maximize the production of monomeric carbohydrates from the structural carbohydrates of feedstocks. One strategy for maximizing carbohydrate production is to identify less recalcitrant feedstock cultivars by performing some type of experimental screening on a large and diverse set of candidate materials, or by identifying genetic modifications (random or directed mutations or transgenic plants) that provide decreased recalcitrance. Economic efficiency can also be increased using additional pretreatment processes such as deacetylation, which uses dilute NaOH to remove the acetyl groups of hemicellulose prior to dilute acid pretreatment. In thismore » work, we used a laboratory-scale screening tool that mimics relevant thermochemical pretreatment conditions to compare the total sugar yield of three near-isogenic brown midrib (bmr) mutant lines and the wild-type (WT) sorghum cultivar. We then compared results obtained from the laboratory-scale screening pretreatment assay to a large-scale pretreatment system. After pretreatment and enzymatic hydrolysis, the bmr mutants had higher total sugar yields than the WT sorghum cultivar. Increased pretreatment temperatures increased reactivity for all sorghum samples reducing the differences observed at lower reaction temperatures. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples, and reduced the differences in total sugar yields among them, but solubilized a sizable fraction of the non-structural carbohydrates. The general trends of increased total sugar yield in the bmr mutant compared to the WT seen at the laboratory scale were observed at the large-scale system. However, in the larger reactor system, the measured total sugar yields were lower and the difference in total sugar yield between the WT and bmr sorghum was larger. Sorghum bmr mutants, which have a reduced lignin content

Genomic architecture of heterosis for yield traits in rice.

PubMed

Huang, Xuehui; Yang, Shihua; Gong, Junyi; Zhao, Qiang; Feng, Qi; Zhan, Qilin; Zhao, Yan; Li, Wenjun; Cheng, Benyi; Xia, Junhui; Chen, Neng; Huang, Tao; Zhang, Lei; Fan, Danlin; Chen, Jiaying; Zhou, Congcong; Lu, Yiqi; Weng, Qijun; Han, Bin

2016-09-29

Increasing grain yield is a long-term goal in crop breeding to meet the demand for global food security. Heterosis, when a hybrid shows higher performance for a trait than both parents, offers an important strategy for crop breeding. To examine the genetic basis of heterosis for yield in rice, here we generate, sequence and record the phenotypes of 10,074 F 2 lines from 17 representative hybrid rice crosses. We classify modern hybrid rice varieties into three groups, representing different hybrid breeding systems. Although we do not find any heterosis-associated loci shared across all lines, within each group, a small number of genomic loci from female parents explain a large proportion of the yield advantage of hybrids over their male parents. For some of these loci, we find support for partial dominance of heterozygous locus for yield-related traits and better-parent heterosis for overall performance when all of the grain-yield traits are considered together. These results inform on the genomic architecture of heterosis and rice hybrid breeding.

A Study of Specialty Clones’ Yield Performance in Early and Late Harvests

USDA-ARS?s Scientific Manuscript database

Technical Abstract: A study was conducted on specialty potato breeding lines to examine yield components in an early and late harvest. Upon first examination it was apparent that the early water cutoff had a large effect on total yield. In the early trial only one clone achieved 600 cwt/A of total...

Crop Diversity for Yield Increase

PubMed Central

Li, Chengyun; He, Xiahong; Zhu, Shusheng; Zhou, Huiping; Wang, Yunyue; Li, Yan; Yang, Jing; Fan, Jinxiang; Yang, Jincheng; Wang, Guibin; Long, Yunfu; Xu, Jiayou; Tang, Yongsheng; Zhao, Gaohui; Yang, Jianrong; Liu, Lin; Sun, Yan; Xie, Yong; Wang, Haining; Zhu, Youyong

2009-01-01

Traditional farming practices suggest that cultivation of a mixture of crop species in the same field through temporal and spatial management may be advantageous in boosting yields and preventing disease, but evidence from large-scale field testing is limited. Increasing crop diversity through intercropping addresses the problem of increasing land utilization and crop productivity. In collaboration with farmers and extension personnel, we tested intercropping of tobacco, maize, sugarcane, potato, wheat and broad bean – either by relay cropping or by mixing crop species based on differences in their heights, and practiced these patterns on 15,302 hectares in ten counties in Yunnan Province, China. The results of observation plots within these areas showed that some combinations increased crop yields for the same season between 33.2 and 84.7% and reached a land equivalent ratio (LER) of between 1.31 and 1.84. This approach can be easily applied in developing countries, which is crucial in face of dwindling arable land and increasing food demand. PMID:19956624

Light propagation and fluorescence quantum yields in liquid scintillators

NASA Astrophysics Data System (ADS)

Buck, C.; Gramlich, B.; Wagner, S.

2015-09-01

For the simulation of the scintillation and Cherenkov light propagation in large liquid scintillator detectors a detailed knowledge about the absorption and emission spectra of the scintillator molecules is mandatory. Furthermore reemission probabilities and quantum yields of the scintillator components influence the light propagation inside the liquid. Absorption and emission properties are presented for liquid scintillators using 2,5-Diphenyloxazole (PPO) and 4-bis-(2-Methylstyryl)benzene (bis-MSB) as primary and secondary wavelength shifter. New measurements of the quantum yields for various aromatic molecules are shown.

Method and apparatus for sampling low-yield wells

DOEpatents

Last, George V.; Lanigan, David C.

2003-04-15

An apparatus and method for collecting a sample from a low-yield well or perched aquifer includes a pump and a controller responsive to water level sensors for filling a sample reservoir. The controller activates the pump to fill the reservoir when the water level in the well reaches a high level as indicated by the sensor. The controller deactivates the pump when the water level reaches a lower level as indicated by the sensors. The pump continuously activates and deactivates the pump until the sample reservoir is filled with a desired volume, as indicated by a reservoir sensor. At the beginning of each activation cycle, the controller optionally can select to purge an initial quantity of water prior to filling the sample reservoir. The reservoir can be substantially devoid of air and the pump is a low volumetric flow rate pump. Both the pump and the reservoir can be located either inside or outside the well.

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS FIREFIGHTING EQUIPMENT Deck Foam System, Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed...

Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

NASA Astrophysics Data System (ADS)

Hurda, Lukáš; Matas, Richard

2017-09-01

Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

49 CFR 173.4a - Excepted quantities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of withstanding without leakage the pressure differential specified in § 173.27(c) of this part. (b... ice), and lithium batteries and cells. (c) Inner packaging limits. The maximum quantity of hazardous..., rigid outer packaging. (5) Placement of the material in the package or packing different materials in...

CALL, Prewriting Strategies, and EFL Writing Quantity

ERIC Educational Resources Information Center

Shafiee, Sajad; Koosha, Mansour; Afghar, Akbar

2015-01-01

This study sought to explore the effect of teaching prewriting strategies through different methods of input delivery (i.e. conventional, web-based, and hybrid) on EFL learners' writing quantity. In its quasi-experimental study, the researchers recruited 98 available sophomores, and assigned them to three experimental groups (conventional,…

7 CFR 945.54 - Minimum quantity exemption.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Minimum quantity exemption. 945.54 Section 945.54 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... regulations issued or in effect pursuant to §§ 945.40 to 945.65, inclusive, or any combination thereof. ...

Examination of synovial fluid hyaluronan quantity and quality in stifle joints of dogs with osteoarthritis.

PubMed

Venable, Rachel O; Stoker, Aaron M; Cook, Cristi R; Cockrell, Mary K; Cook, James L

2008-12-01

To determine the quantity (concentration) and quality (molecular weight) of synovial fluid hyaluronan with respect to presence and severity of osteoarthritis in stifle joints of dogs. 21 purpose-bred dogs and 6 clinically affected large-breed dogs (cranial cruciate ligament [CrCL] disease with secondary osteoarthritis). Research dogs underwent arthroscopic surgery in 1 stifle joint to induce osteoarthritis via CrCL transection (CrCLt; n=5 stifle joints), femoral condylar articular cartilage groove creation (GR; 6), or meniscal release (MR; 5); 5 had sham surgery (SH) performed. Contralateral stifle joints (n=21) were used as unoperated control joints. Synovial fluid was obtained from research dogs at time 0 and 12 weeks after surgery and from clinically affected dogs prior to surgery. All dogs were assessed for lameness, radiographic signs of osteoarthritis, and pathologic findings on arthroscopy as well as for quantity and quality of hyaluronan. Clinically affected dogs had significantly greater degrees of pathologic findings, compared with dogs with surgically induced osteoarthritis (ie, those with CrCLt, GR, and MR stifle joints), and with respect to lameness scores, radiographic signs of osteoarthritis, pathologic findings on arthroscopy, and synovial fluid hyaluronan concentration. Synovial fluid from stifle joints of dogs with surgically induced osteoarthritis had hyaluronan bands at 35 kd on western blots that synovial fluid from SH and clinically affected stifle joints did not. Synovial fluid hyaluronan quantity and quality were altered in stifle joints of dogs with osteoarthritis, compared with control stifle joints. A specific hyaluronan protein fragment may be associated with early pathologic changes in affected joints.

A meteorologically-driven yield reduction model for spring and winter wheat

NASA Technical Reports Server (NTRS)

Ravet, F. W.; Cremins, W. J.; Taylor, T. W.; Ashburn, P.; Smika, D.; Aaronson, A. (Principal Investigator)

1983-01-01

A yield reduction model for spring and winter wheat was developed for large-area crop condition assessment. Reductions are expressed in percentage from a base yield and are calculated on a daily basis. The algorithm contains two integral components: a two-layer soil water budget model and a crop calendar routine. Yield reductions associated with hot, dry winds (Sukhovey) and soil moisture stress are determined. Input variables include evapotranspiration, maximum temperature and precipitation; subsequently crop-stage, available water holding percentage and stress duration are evaluated. No specific base yield is required and may be selected by the user; however, it may be generally characterized as the maximum likely to be produced commercially at a location.

X-ray power and yield measurements at the refurbished Z machine

DOE PAGES

Jones, M. C.; Ampleford, D. J.; Cuneo, M. E.; ...

2014-08-04

Advancements have been made in the diagnostic techniques to measure accurately the total radiated x-ray yield and power from z-pinch loads at the Z Machine with high accuracy. The Z-accelerator is capable of outputting 2MJ and 330 TW of x-ray yield and power, and accurately measuring these quantities is imperative. We will describe work over the past several years which include the development of new diagnostics, improvements to existing diagnostics, and implementation of automated data analysis routines. A set of experiments were conducted on the Z machine where the load and machine configuration were held constant. During this shot series,more » it was observed that total z-pinch x-ray emission power determined from the two common techniques for inferring the x-ray power, Kimfol filtered x-ray diode diagnostic and the Total Power and Energy diagnostic gave 450 TW and 327 TW respectively. Our analysis shows the latter to be the more accurate interpretation. More broadly, the comparison demonstrates the necessity to consider spectral response and field of view when inferring xray powers from z-pinch sources.« less

Primary factors affecting water quality and quantity in four watersheds in Eastern Puerto Rico

USGS Publications Warehouse

Murphy, Sheila F.; Stallard, Robert F.

2009-01-01

As part of the U.S. Geological Survey (USGS) Water, Energy, and Biogeochemical Budgets (WEBB) program, four small watersheds in eastern Puerto Rico were monitored to identify and evaluate the effects of geology, landcover, atmospheric deposition, and other factors on stream water quality and quantity. Two catchments are located on coarse-grained granitic plutonic rocks, which weather to quartz- and clay-rich, sandy soils, and two are located on fine-grained volcanic rocks and volcaniclastic sediments, which weather to quartz-poor, fine-grained soils. These differing soil materials result in different hydrologic regimes. Soils on the granitic rocks have greater permeability than those developed on the volcaniclastic rocks, allowing more water infiltration and potentially greater landslide erosion rates. For each bedrock type, one catchment was covered with mature rainforest, and the other catchment was affected by agricultural practices typical of eastern Puerto Rico. These practices led to the erosion of much of the original surface soil in the agricultural watersheds, which introduced large quantities of sediment to stream channels. The agricultural watersheds are undergoing natural reforestation, like much of Puerto Rico. Eastern Puerto Rico receives large atmospheric inputs of marine salts, pollutants from the Northern Hemisphere, and Saharan Desert dust. Marine salts contribute over 80 percent of the ionic charge in precipitation, with peak inputs in January. Intense storms, mostly hurricanes, are associated with exceptionally high chloride concentrations in stream waters. Temperate pollution contributes nitrate, ammonia, and sulfate, with maximum inputs during northern cold fronts in January, April, and May. Pollution inputs have increased through time. Desert dust peaks in June and July, during times of maximum dust transport from the Saharan Desert across the Atlantic Ocean.

CultureMap: FORCEnet Science and Technology Large Tactical Sensor Networks II Program

DTIC Science & Technology

2014-11-14

around those situations. These types of sources, however, yield an even more massive quantity of content that is almost exclusively textual and...intelligence gaps with respect to the data saved for people, places, groups, and regions that have been stored in the system with respect to required entity...and maize products are being distributed in affected areas, thus ensuring that each person receives 1500 calories of food per day. Sentiment data

Does photodissociation of molecular oxygen from myoglobin and hemoglobin yield singlet oxygen?

PubMed

Lepeshkevich, Sergei V; Stasheuski, Alexander S; Parkhats, Marina V; Galievsky, Victor A; Dzhagarov, Boris M

2013-03-05

Time-resolved luminescence measurements in the near-infrared region indicate that photodissociation of molecular oxygen from myoglobin and hemoglobin does not produce detectable quantities of singlet oxygen. A simple and highly sensitive method of luminescence quantification is developed and used to determine the upper limit for the quantum yield of singlet oxygen production. The proposed method was preliminarily evaluated using model data sets and confirmed with experimental data for aqueous solutions of 5,10,15,20-tetrakis(4-N-methylpyridyl) porphyrin. A general procedure for error estimation is suggested. The method is shown to provide a determination of the integral luminescence intensity in a wide range of values even for kinetics with extremely low signal-to-noise ratio. The present experimental data do not deny the possibility of singlet oxygen generation during the photodissociation of molecular oxygen from myoglobin and hemoglobin. However, the photodissociation is not efficient to yield singlet oxygen escaped from the proteins into the surrounding medium. The upper limits for the quantum yields of singlet oxygen production in the surrounding medium after the photodissociation for oxyhemoglobin and oxymyoglobin do not exceed 3.4×10(-3) and 2.3×10(-3), respectively. On the average, no more than one molecule of singlet oxygen from every hundred photodissociated oxygen molecules can succeed in escaping from the protein matrix. Copyright © 2013 Elsevier B.V. All rights reserved.

Role of the N*(1535) in pp{yields}pp{phi} and {pi}{sup -}p{yields}n{phi} reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie Jujun; Graduate University of Chinese Academy of Sciences, Beijing 100049; Zou Bingsong

2008-01-15

The near-threshold {phi}-meson production in proton-proton and {pi}{sup -}p collisions is studied with the assumption that the production mechanism is due to the sub-N{phi}-threshold N*(1535) resonance. The {pi}{sup 0}-,{eta}-, and {rho}{sup 0}-meson exchanges for proton-proton collisions are considered. It is shown that the contribution to the pp{yields}pp{phi} reaction from the t-channel {pi}{sup 0}-meson exchange is dominant. With a significant N*(1535)N{phi} coupling [g{sub N*(1535)N{phi}}{sup 2}/4{pi}=0.13], both pp{yields}pp{phi} and {pi}{sup -}p{yields}n{phi} data are very well reproduced. The significant coupling of the N*(1535) resonance to N{phi} is compatible with previous indications of a large ss component in the quark wave function of themore » N*(1535) resonance and may be the real origin of the significant enhancement of the {phi} production over the naive OZI-rule predictions.« less

16 CFR 1.23 - Quantity limit rules.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

Stochastic Models of Macroscale Quantities for the Prediction of the REV Scale for Multiphase Flow through Porous Media

NASA Astrophysics Data System (ADS)

Talbot, C.; McClure, J. E.; Armstrong, R. T.; Mostaghimi, P.; Hu, Y.; Miller, C. T.

2017-12-01

Microscale experimental and computational methods can be used to evaluate fundamental microscale mechanisms and deduce macroscale constitutive relationships and parameter values. The link between the microscale and the macroscale is especially demanding, because technical issues arise regarding the necessary scale of the system needed for a meaningful set of macroscale measures to be insensitive to the size of the system, which is known as a representative elementary volume (REV). While the REV scale is routinely determined for single-phase flow in porous media, no systematic study of the scale of a REV for the comprehensive set of macroscale measures considered here has been reported in the literature. A comprehensive set of measures of the macroscale state is developed. We further develop and apply methods to predict the REV scale and quantify the uncertainty of the estimate for this set of macroscale quantities. We model the system state in terms of standard errors of macroscale quantities as a multivariate Gaussian process dependent on the size of the domain simulated. We determine predictive distributions of function values and a posterior distributions of weights using standard kernels, as well as a kernel constructed using relationships between physical quantities. For each kernel, we discuss the decay of the mean and covariance with increasing domain size, and use cross-validation to facilitate model selection. The procedure yields a model of the domain size needed to achieve a REV with quantifiable uncertainty. We present results in the context of multiphase fluid flow through a highly resolved realization of sandstone imaged using micro-CT. A 1440x1440x4320 section of the full 2520x2520x5280 imaged medium is simulated using the lattice-Boltzmann method. We compare the fidelity of the predictive model with results obtained by an analogous approach using polynomial regression.

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

46 CFR 34.20-5 - Quantity of foam required-T/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Quantity of foam required-T/ALL. 34.20-5 Section 34.20-5..., Details § 34.20-5 Quantity of foam required—T/ALL. (a) Area protected. Systems of this type are designed... liters/min per square meter of cargo tanks deck area, where cargo tanks deck area means the maximum...

Breeding high-yielding drought-tolerant rice: genetic variations and conventional and molecular approaches

PubMed Central

Kumar, Arvind; Dixit, Shalabh; Ram, T.; Yadaw, R. B.; Mishra, K. K.; Mandal, N. P.

2014-01-01

The increased occurrence and severity of drought stress have led to a high yield decline in rice in recent years in drought-affected areas. Drought research at the International Rice Research Institute (IRRI) over the past decade has concentrated on direct selection for grain yield under drought. This approach has led to the successful development and release of 17 high-yielding drought-tolerant rice varieties in South Asia, Southeast Asia, and Africa. In addition to this, 14 quantitative trait loci (QTLs) showing a large effect against high-yielding drought-susceptible popular varieties were identified using grain yield as a selection criterion. Six of these (qDTY 1.1, qDTY 2.2, qDTY 3.1, qDTY 3.2, qDTY 6.1, and qDTY 12.1) showed an effect against two or more high-yielding genetic backgrounds in both the lowland and upland ecosystem, indicating their usefulness in increasing the grain yield of rice under drought. The yield of popular rice varieties IR64 and Vandana has been successfully improved through a well-planned marker-assisted backcross breeding approach, and QTL introgression in several other popular varieties is in progress. The identification of large-effect QTLs for grain yield under drought and the higher yield increase under drought obtained through the use of these QTLs (which has not been reported in other cereals) indicate that rice, because of its continuous cultivation in two diverse ecosystems (upland, drought tolerant, and lowland, drought susceptible), has benefited from the existence of larger genetic variability than in other cereals. This can be successfully exploited using marker-assisted breeding. PMID:25205576

Urgency of increasing the quantity and quality of student creativity program

NASA Astrophysics Data System (ADS)

Sarmini; Prasetya, Ketut; Nadiroh, Ulin

2018-01-01

Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

What aspects of future rainfall changes matter for crop yields in West Africa?

NASA Astrophysics Data System (ADS)

Guan, Kaiyu; Sultan, Benjamin; Biasutti, Michela; Baron, Christian; Lobell, David B.

2015-10-01

How rainfall arrives, in terms of its frequency, intensity, the timing and duration of rainy season, may have a large influence on rainfed agriculture. However, a thorough assessment of these effects is largely missing. This study combines a new synthetic rainfall model and two independently validated crop models (APSIM and SARRA-H) to assess sorghum yield response to possible shifts in seasonal rainfall characteristics in West Africa. We find that shifts in total rainfall amount primarily drive the rainfall-related crop yield change, with less relevance to intraseasonal rainfall features. However, dry regions (total annual rainfall below 500 mm/yr) have a high sensitivity to rainfall frequency and intensity, and more intense rainfall events have greater benefits for crop yield than more frequent rainfall. Delayed monsoon onset may negatively impact yields. Our study implies that future changes in seasonal rainfall characteristics should be considered in designing specific crop adaptations in West Africa.

Conservation laws and conserved quantities for (1+1)D linearized Boussinesq equations

NASA Astrophysics Data System (ADS)

Carvalho, Cindy; Harley, Charis

2017-05-01

Conservation laws and physical conserved quantities for the (1+1)D linearized Boussinesq equations at a constant water depth are presented. These equations describe incompressible, inviscid, irrotational fluid flow in the form of a non steady solitary wave. A systematic multiplier approach is used to obtain the conservation laws of the system of third order partial differential equations (PDEs) in dimensional form. Physical conserved quantities are derived by integrating the conservation laws in the direction of wave propagation and imposing decaying boundary conditions in the horizontal direction. One of these is a newly discovered conserved quantity which relates to an energy flux density.

Measurement of fission yields and isomeric yield ratios at IGISOL

NASA Astrophysics Data System (ADS)

Pomp, Stephan; Mattera, Andrea; Rakopoulos, Vasileios; Al-Adili, Ali; Lantz, Mattias; Solders, Andreas; Jansson, Kaj; Prokofiev, Alexander V.; Eronen, Tommi; Gorelov, Dimitri; Jokinen, Ari; Kankainen, Anu; Moore, Iain D.; Penttilä, Heikki; Rinta-Antila, Sami

2018-03-01

Data on fission yields and isomeric yield ratios (IYR) are tools to study the fission process, in particular the generation of angular momentum. We use the IGISOL facility with the Penning trap JYFLTRAP in Jyväskylä, Finland, for such measurements on 232Th and natU targets. Previously published fission yield data from IGISOL concern the 232Th(p,f) and 238U(p,f) reactions at 25 and 50 MeV. Recently, a neutron source, using the Be(p,n) reaction, has been developed, installed and tested. We summarize the results for (p,f) focusing on the first measurement of IYR by direct ion counting. We also present first results for IYR and relative yields for Sn and Sb isotopes in the 128-133 mass range from natU(n,f) based on γ-spectrometry. We find a staggering behaviour in the cumulative yields for Sn and a shift in the independent fission yields for Sb as compared to current evaluations. Plans for the future experimental program on fission yields and IYR measurements are discussed.

Variation and Change in Northern Bavarian Quantity

ERIC Educational Resources Information Center

Drake, Derek

2013-01-01

This dissertation presents new research on the "Bavarian Quantity Law" (the BQL) in the northern Bavarian dialect of Hahnbach. Building upon earlier investigation of the BQL (cf. Bannert 1976a,b for Central Bavarian) this study examines the historical, phonological, and phonetic motivations for this feature as well the variability in its…

10 CFR 26.109 - Urine specimen quantity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

10 CFR 26.109 - Urine specimen quantity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

10 CFR 26.109 - Urine specimen quantity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Urine specimen quantity. 26.109 Section 26.109 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Collecting Specimens for Testing § 26.109 Urine... shall encourage the donor to drink a reasonable amount of liquid (normally, 8 ounces of water every 30...

Stormwater management impacts on urban stream water quality and quantity during and after development in Clarksburg, MD

NASA Astrophysics Data System (ADS)

Loperfido, J. V.; Noe, G. B.; Jarnagin, S.; Mohamoud, Y. M.; Van Ness, K.; Hogan, D. M.

2012-12-01

Urbanization and urban land use leads to degradation of local stream habitat and 'urban stream syndrome.' Best Management Practices (BMPs) are often used in an attempt to mitigate the impact of urban land use on stream water quality and quantity. Traditional development has employed stormwater BMPs that were placed in a centralized manner located either in the stream channel or near the riparian zone to treat stormwater runoff from large drainage areas; however, urban streams have largely remained impaired. Recently, distributed placement of BMPs throughout the landscape has been implemented in an attempt to detain, treat, and infiltrate stormwater runoff from smaller drainage areas near its source. Despite increasing implementation of distributed BMPs, little has been reported on the catchment-scale (1-10 km^2) performance of distributed BMPs and how they compare to centralized BMPs. The Clarksburg Special Protection Area (CSPA), located in the Washington, DC exurbs within the larger Chesapeake Bay watershed, is undergoing rapid urbanization and employs distributed BMPs on the landscape that treat small drainage areas with the goal of preserving high-quality stream resources in the area. In addition, the presence of a nearby traditionally developed (centralized BMPs) catchment and an undeveloped forested catchment makes the CSPA an ideal setting to understand how the best available stormwater management technology implemented during and after development affects stream water quality and quantity through a comparative watershed analysis. The Clarksburg Integrated Monitoring Partnership is a consortium of local and federal agencies and universities that conducts research in the CSPA including: monitoring of stream water quality, geomorphology, and biology; analysis of stream hydrological and water quality data; and GIS mapping and analysis of land cover, elevation change and BMP implementation data. Here, the impacts of urbanization on stream water quantity

6 CFR 27.203 - Calculating the screening threshold quantity by security issue.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 6 Domestic Security 1 2012-01-01 2012-01-01 false Calculating the screening threshold quantity by security issue. 27.203 Section 27.203 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE... the screening threshold quantity by security issue. (a) General. In calculating whether a facility...

Contribution of insect pollinators to crop yield and quality varies with agricultural intensification

PubMed Central

Potts, Simon G.; Steffan-Dewenter, Ingolf; Vaissière, Bernard E.; Woyciechowski, Michal; Krewenka, Kristin M.; Tscheulin, Thomas; Roberts, Stuart P.M.; Szentgyörgyi, Hajnalka; Westphal, Catrin; Bommarco, Riccardo

2014-01-01

Background. Up to 75% of crop species benefit at least to some degree from animal pollination for fruit or seed set and yield. However, basic information on the level of pollinator dependence and pollinator contribution to yield is lacking for many crops. Even less is known about how insect pollination affects crop quality. Given that habitat loss and agricultural intensification are known to decrease pollinator richness and abundance, there is a need to assess the consequences for different components of crop production. Methods. We used pollination exclusion on flowers or inflorescences on a whole plant basis to assess the contribution of insect pollination to crop yield and quality in four flowering crops (spring oilseed rape, field bean, strawberry, and buckwheat) located in four regions of Europe. For each crop, we recorded abundance and species richness of flower visiting insects in ten fields located along a gradient from simple to heterogeneous landscapes. Results. Insect pollination enhanced average crop yield between 18 and 71% depending on the crop. Yield quality was also enhanced in most crops. For instance, oilseed rape had higher oil and lower chlorophyll contents when adequately pollinated, the proportion of empty seeds decreased in buckwheat, and strawberries’ commercial grade improved; however, we did not find higher nitrogen content in open pollinated field beans. Complex landscapes had a higher overall species richness of wild pollinators across crops, but visitation rates were only higher in complex landscapes for some crops. On the contrary, the overall yield was consistently enhanced by higher visitation rates, but not by higher pollinator richness. Discussion. For the four crops in this study, there is clear benefit delivered by pollinators on yield quantity and/or quality, but it is not maximized under current agricultural intensification. Honeybees, the most abundant pollinator, might partially compensate the loss of wild pollinators in

Contribution of insect pollinators to crop yield and quality varies with agricultural intensification.

PubMed

Bartomeus, Ignasi; Potts, Simon G; Steffan-Dewenter, Ingolf; Vaissière, Bernard E; Woyciechowski, Michal; Krewenka, Kristin M; Tscheulin, Thomas; Roberts, Stuart P M; Szentgyörgyi, Hajnalka; Westphal, Catrin; Bommarco, Riccardo

2014-01-01

Background. Up to 75% of crop species benefit at least to some degree from animal pollination for fruit or seed set and yield. However, basic information on the level of pollinator dependence and pollinator contribution to yield is lacking for many crops. Even less is known about how insect pollination affects crop quality. Given that habitat loss and agricultural intensification are known to decrease pollinator richness and abundance, there is a need to assess the consequences for different components of crop production. Methods. We used pollination exclusion on flowers or inflorescences on a whole plant basis to assess the contribution of insect pollination to crop yield and quality in four flowering crops (spring oilseed rape, field bean, strawberry, and buckwheat) located in four regions of Europe. For each crop, we recorded abundance and species richness of flower visiting insects in ten fields located along a gradient from simple to heterogeneous landscapes. Results. Insect pollination enhanced average crop yield between 18 and 71% depending on the crop. Yield quality was also enhanced in most crops. For instance, oilseed rape had higher oil and lower chlorophyll contents when adequately pollinated, the proportion of empty seeds decreased in buckwheat, and strawberries' commercial grade improved; however, we did not find higher nitrogen content in open pollinated field beans. Complex landscapes had a higher overall species richness of wild pollinators across crops, but visitation rates were only higher in complex landscapes for some crops. On the contrary, the overall yield was consistently enhanced by higher visitation rates, but not by higher pollinator richness. Discussion. For the four crops in this study, there is clear benefit delivered by pollinators on yield quantity and/or quality, but it is not maximized under current agricultural intensification. Honeybees, the most abundant pollinator, might partially compensate the loss of wild pollinators in

Associated strangeness production in the pp{yields}pK{sup +}K{sup -}p and pp{yields}pK{sup +{pi}0{Sigma}0} reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie Jujun; Department of Physics, Zhengzhou University, Zhengzhou, Henan 450001; Wilkin, Colin

2010-08-15

The total and differential cross sections for associated strangeness production in the pp{yields}pK{sup +}K{sup -}p and pp{yields}pK{sup +{pi}0{Sigma}0} reactions have been studied in a unified approach using an effective Lagrangian model. It is assumed that both the K{sup -}p and {pi}{sup 0{Sigma}0} final states originate from the decay of the {Lambda}(1405) that was formed in the production chain pp{yields}p(N*(1535){yields}K{sup +{Lambda}}(1405)). The available experimental data are well reproduced, especially the ratio of the two total cross sections, which is much less sensitive to the particular model of the entrance channel. The significant coupling of the N*(1535) to {Lambda}(1405)K is further evidencemore » for large ss-bar components in the quark wave function of the N*(1535).« less

Slope Controls Grain Yield and Climatic Yield in Mountainous Yunnan province, China

NASA Astrophysics Data System (ADS)

Duan, X.; Rong, L.; Gu, Z.; Feng, D.

2017-12-01

Mountainous regions are increasingly vulnerable to food insecurity because of limited arable land, growing population pressure, and climate change. Development of sustainable mountain agriculture will require an increased understanding of the effects of environmental factors on grain and climatic yields. The objective of this study was to explore the relationships between actual grain yield, climatic yield, and environmental factors in a mountainous region in China. We collected data on the average grain yield per unit area in 119 counties in Yunnan province from 1985 to 2012, and chose 17 environmental factors for the same period. Our results showed that actual grain yield ranged from 1.43 to 6.92 t·ha-1, and the climatic yield ranged from -0.15 to -0.01 t·ha-1. Lower climatic yield but higher grain yield was generally found in central areas and at lower slopes and elevations in the western and southwestern counties of Yunnan province. Higher climatic yield but lower grain yield were found in northwestern parts of Yunnan province on steep slopes. Annual precipation and temperature had a weak influence on the climatic yield. Slope explained 44.62 and 26.29% of the variation in grain yield and climatic yield. The effects of topography on grain and climatic yields were greater than climatic factors. Slope was the most important environmental variable for the variability in climatic and grain yields in the mountainous Yunnan province due to the highly heterogeneous topographic conditions. Conversion of slopes to terraces in areas with higher climatic yields is an effective way to maintain grain production in response to climate variability. Additionally, soil amendments and soil and water conservation measures should be considered to maintain soil fertility and aid in sustainable development in central areas, and in counties at lower slopes and elevations in western and southwestern Yunnan province.