The effect of zinc on the aluminum anode of the aluminum-air battery

NASA Astrophysics Data System (ADS)

Tang, Yougen; Lu, Lingbin; Roesky, Herbert W.; Wang, Laiwen; Huang, Baiyun

Aluminum is an ideal material for batteries, due to its excellent electrochemical performance. Herein, the effect of zinc on the aluminum anode of the aluminum-air battery, as an additive for aluminum alloy and electrolytes, has been studied. The results show that zinc can decrease the anodic polarization, restrain the hydrogen evolution and increase the anodic utilization rate.

Relations of benthic macroinvertebrates to concentrations of trace elements in water, streambed sediments, and transplanted bryophytes and stream habitat conditions in nonmining and mining areas of the upper Colorado River basin, Colorado, 1995-98

USGS Publications Warehouse

Mize, Scott V.; Deacon, Jeffrey R.

2002-01-01

Intensive mining activity and highly mineralized rock formations have had significant impacts on surface-water and streambed-sediment quality and aquatic life within the upper reaches of the Uncompahgre River in western Colorado. A synoptic study by the U.S. Geological Survey National Water-Quality Assessment Program was completed in the upper Uncompahgre River Basin in 1998 to better understand the relations of trace elements (with emphasis on aluminum, arsenic, copper, iron, lead, and zinc concentrations) in water, streambed sediment, and aquatic life. Water-chemistry, streambed-sediment, and benthic macroinvertebrate samples were collected during low-flow conditions between October 1995 and July 1998 at five sites on the upper Uncompahgre River, all downstream from historical mining, and at three sites in drainage basins of the Upper Colorado River where mining has not occurred. Aquatic bryophytes were transplanted to all sites for 15 days of exposure to the water column during which time field parameters were measured and chemical water-quality and benthic macroinvertebrate samples were collected. Stream habitat characteristics also were documented at each site. Certain attributes of surface-water chemistry among streams were significantly different. Concentrations of total aluminum, copper, iron, lead, and zinc in the water column and concentrations of dissolved aluminum, copper, and zinc were significantly different between nonmining and mining sites. Some sites associated with mining exceeded Colorado acute aquatic-life standards for aluminum, copper, and zinc and exceeded Colorado chronic aquatic-life standards for aluminum, copper, iron, lead, and zinc. Concentrations of copper, lead, and zinc in streambed sediments were significantly different between nonmining and mining sites. Generally, concentrations of arsenic, copper, lead, and zinc in streambed sediments at mining sites exceeded the Canadian Sediment Quality Guidelines probable effect level (PEL), except at two mining sites where concentrations of copper and zinc were below the PEL. Concentrations of arsenic, copper, iron, and lead in transplanted bryophytes were significantly different between nonmining and mining sites. Bioconcentration factors calculated for 15-day exposure using one-half of the minimum reporting level were significantly different between nonmining and mining sites. In general, concentrations of trace elements in streambed sediment and transplanted bryophytes were more closely correlated than were the concentrations of trace elements in the water column with streambed sediments or concentrations in the water column with transplanted bryophytes. Stream habitat was rated as optimal to suboptimal using the U.S. Environmental Protection Agency Rapid Bioassessment Protocols for all sites in the study area. Generally, stream habitat conditions were similar at nonmining compared to mining sites and were suitable for diverse macroinvertebrate communities. All study sites had optimal instream habitat except two mining sites with suboptimal instream habitat because of disturbances in stream habitat. The benthic macroinvertebrate community composition at nonmining sites and mining sites differed. Mining sites had significantly lower total abundance of macroinvertebrates, fewer numbers of taxa, and lower dominance of Ephemeroptera (mayflies), Plecoptera (stoneflies), and Trichoptera (caddisflies), and a larger percentage of tolerant species than did nonmining sites. The predominance of Baetis sp. (mayflies), Hydropsychidae (caddisflies), and large percentage of Orthocladiinae chironomids (midges) at mining sites indicated that these species may be tolerant to elevated trace-element concentrations. The absence of Heptageniidae (mayflies), Chloroperlidae (stoneflies), and Rhyacophila sp. (caddisflies) at mining sites indicated that these species may be sensitive to elevated trace-element concentrations. Comparison of field parameters and

Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Groundwater Quality and Remediation Progress at DoD Sites

DTIC Science & Technology

2007-02-01

years if kept refrigerated in its preservative solution of ethanol, sodium benzoate , and ethylene diamine tetra-acetic acid (EDTA). Alternatively... sodium bicarbonate solution, EDTA, and sodium azide solution to remove residual gylcerol, sulfide, cadmium, chromium, copper, iron, nickel, zinc, and lead...Magnesium Cadmium Nickel Potassium Chromium Selenium Sodium Copper Vanadium Aluminum Iron Zinc Arsenic Lead Antimony Manganese Anions (1-3 days

ALLOY COATINGS AND METHOD OF APPLYING

DOEpatents

Eubank, L.D.; Boller, E.R.

1958-08-26

A method for providing uranium articles with a pro tective coating by a single dip coating process is presented. The uranium article is dipped into a molten zinc bath containing a small percentage of aluminum. The resultant product is a uranium article covered with a thin undercoat consisting of a uranium-aluminum alloy with a small amount of zinc, and an outer layer consisting of zinc and aluminum. The article may be used as is, or aluminum sheathing may then be bonded to the aluminum zinc outer layer.

Determination of the Mineral Composition and Toxic Element Contents of Propolis by Near Infrared Spectroscopy

PubMed Central

González-Martín, M. Inmaculada; Escuredo, Olga; Revilla, Isabel; Vivar-Quintana, Ana M.; Coello, M. Carmen; Palacios Riocerezo, Carlos; Wells Moncada, Guillermo

2015-01-01

The potential of near infrared spectroscopy (NIR) with remote reflectance fiber-optic probes for determining the mineral composition of propolis was evaluated. This technology allows direct measurements without prior sample treatment. Ninety one samples of propolis were collected in Chile (Bio-Bio region) and Spain (Castilla-León and Galicia regions). The minerals measured were aluminum, calcium, iron, potassium, magnesium, phosphorus, and some potentially toxic trace elements such as zinc, chromium, nickel, copper and lead. The modified partial least squares (MPLS) regression method was used to develop the NIR calibration model. The determination coefficient (R2) and root mean square error of prediction (RMSEP) obtained for aluminum (0.79, 53), calcium (0.83, 94), iron (0.69, 134) potassium (0.95, 117), magnesium (0.70, 99), phosphorus (0.94, 24) zinc (0.87, 10) chromium (0.48, 0.6) nickel (0.52, 0.7) copper (0.64, 0.9) and lead (0.70, 2) in ppm. The results demonstrated that the capacity for prediction can be considered good for wide ranges of potassium, phosphorus and zinc concentrations, and acceptable for aluminum, calcium, magnesium, iron and lead. This indicated that the NIR method is comparable to chemical methods. The method is of interest in the rapid prediction of potentially toxic elements in propolis before consumption. PMID:26540058

Characteristics of joining and hybrid composite forging of aluminum solid parts and galvanized steel sheets

NASA Astrophysics Data System (ADS)

Wesling, V.; Treutler, K.; Bick, T.; Stonis, M.; Langner, J.; Kriwall, M.

2018-06-01

In lightweight construction, light metals like aluminum are used in addition to high-strength steels. However, a welded joint of aluminum and steel leads to the precipitation of brittle, intermetallic phases and contact corrosion. Nevertheless, to use the advantages of this combination in terms of weight saving composite hybrid forging has been developed. In this process, an aluminum solid part and a steel sheet were formed in a single step and joined at the same time with zinc as brazing material. For this purpose, the zinc was applied by hot dipping on the aluminum in order to produce a connection via this layer in a forming process, under pressure and heat. Due to the formed intermediate layer of zinc, the formation of the Fe-Al intermetallic phases and the contact corrosion are excluded. By determining the mathematical relationships between joining parameters and the connection properties the strength of a specific joint geometry could be adjusted to reach the level of conventional joining techniques. In addition to the presentation of the joint properties, the influence of the joining process on the structure of the involved materials is also shown. Furthermore, the failure behavior under static tensile and shear stress will be shown.

Concentrations and bioaccessibility of metals in vegetation and dust near a mining haul road, Cape Krusenstern National Monument, Alaska

USGS Publications Warehouse

Brumbaugh, W.G.; Morman, S.A.; May, T.W.

2011-01-01

Vegetation, sub-surface peat, and road dust were sampled near the Delong Mountain Transportation System (DMTS) haul road in northwest Alaska in 2005-2006 to document aluminum, barium, cadmium, lead, and zinc concentrations, and to evaluate bioaccessibility of these metals. The DMTS haul road is the transport corridor between Red Dog Mine (a large-scale, lead-zinc mine and mill) and the coastal shipping port, and it traverses National Park Service lands. Compared to reference locations, total metal concentrations in four types of vegetation (birch, cranberry, and willow leaves, and cotton grass blades/stalks) collected 25 m from the haul road were enriched on average by factors of 3.5 for zinc, 8.0 for barium, 20 for cadmium, and 150 for lead. Triple rinsing of vegetation with a water/methanol mixture reduced metals concentrations by at most 50%, and cadmium and zinc concentrations were least affected by rinsing. Cadmium and zinc bioaccessibility was greater in vegetation (50% to 100%) than in dust (15% to 20%); whereas the opposite pattern was observed for lead bioaccessibility (<30% in vegetation; 50% in dust). Barium exhibited low-to-intermediate bioaccessibility in dust and vegetation (20% to 40%), whereas aluminum bioaccessibility was relatively low (<6%) in all sample types. Our reconnaissance-level study indicates that clean-up and improvements in lead/zinc concentrate transfer activities have been effective; however, as of 2006, metal dispersion from past and/or present releases of fugitive dusts along the DMTS road still may have been contributing to elevated metals in surface vegetation. Vegetation was most enriched in lead, but because bioaccessibility of cadmium was greater, any potential risks to animals that forage near the haul road might be equally important for both of these metals. ?? 2011 Springer Science+Business Media B.V. (outside the USA).

Chemical analyses of stream sediment in the Tar Creek basin of the Picher mining area, northeast Oklahoma

USGS Publications Warehouse

Parkhurst, David L.; Doughten, Michael; Hearn,, Paul P.

1988-01-01

Chemical analyses are presented for 47 sediment samples from the Tar Creek drainage in the Picher mining area of northeast Oklahoma. The samples were taken in December 1983, June 1984, and June 1985. All of the samples were taken downstream from mine-water discharge points of abandoned lead and zinc mines. The 34 samples taken in December 1983 and June 1984 were analyzed semiquantitatively by emission spectrography for 64 elements and quantitatively for cadmium, copper, iron, manganese, nickel, lead, sulfur, zinc, and organic carbon. The 13 samples taken in June 1985 were analyzed quantitatively for aluminum, cadmium, cobalt, chromium, copper, iron, manganese, molybdenum, nickel, phosphorus, lead, sulfur, silicon, titanium, vanadium, zinc, and organic carbon.

Corrosion-resistant uranium

DOEpatents

Hovis, V.M. Jr.; Pullen, W.C.; Kollie, T.G.; Bell, R.T.

1981-10-21

The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

Corrosion-resistant uranium

DOEpatents

Hovis, Jr., Victor M.; Pullen, William C.; Kollie, Thomas G.; Bell, Richard T.

1983-01-01

The present invention is directed to the protecting of uranium and uranium alloy articles from corrosion by providing the surfaces of the articles with a layer of an ion-plated metal selected from aluminum and zinc to a thickness of at least 60 microinches and then converting at least the outer surface of the ion-plated layer of aluminum or zinc to aluminum chromate or zinc chromate. This conversion of the aluminum or zinc to the chromate form considerably enhances the corrosion resistance of the ion plating so as to effectively protect the coated article from corrosion.

Ferrous Analysis.

ERIC Educational Resources Information Center

Straub, William A.

1989-01-01

Elements covered in this review include: aluminum, antimony, arsenic, bismuth, boron, calcium, carbon, chromium, cobalt, copper, hydrogen, iron, lead, magnesium, manganese, molybdenum, nickel, niobium, nitrogen, oxygen, phosphorus, platinum, rare earths, silicons, sulfur, tin, titanium, tungsten, vanadium, zinc, and zirconium. Analytical methods…

Mineral resource of the month: lead

USGS Publications Warehouse

Guberman, David E.

2010-01-01

The article discusses the properties and uses lead as a mineral resource. According to the author, lead is a corrosion-resistant, dense, ductile, and malleable blue-gray metal that has been used by humans for 5,000 years. Lead was first used in decorative, fixtures, roofs, pipes, and windows. The author says that lead is the fifth-most consumed metal based on tonnage after iron, aluminum, copper and zinc.

Facile Route to Rare Heterobimetallic Aluminum-Copper and Aluminum-Zinc Selenide Clusters.

PubMed

Li, Bin; Li, Jiancheng; Liu, Rui; Zhu, Hongping; Roesky, Herbert W

2017-03-20

Heterobimetallic aluminum-copper and aluminum-zinc clusters were prepared from the reaction of LAl(SeH) 2 [1; L = HC(CMeNAr) 2 and Ar = 2,6-iPr 2 C 6 H 3 ] with (MesCu) 4 and ZnEt 2 , respectively. The resulting clusters with the core structures of Al 2 Se 4 Cu 4 and Al 2 Se 4 Zn 3 exhibit unique metal-organic frameworks. This is a novel pathway for the synthesis of aluminum-copper and aluminum-zinc selenides. The products have been characterized by spectroscopic methods and single-crystal X-ray structural characterization.

A survey of the concentrations of eleven metals in vaccines, allergenic extracts, toxoids, blood, blood derivatives and other biological products.

PubMed

May, J C; Rains, T C; Maienthal, F J; Biddle, G N; Progar, J J

1986-10-01

Approximately 85 samples of injectable biological products regulated by the Center for Drugs and Biologics of the United States Food and Drug Administration were surveyed for the presence of 11 elements, namely aluminum, arsenic, barium, cadmium, chromium, lead, mercury, selenium, thallium and zinc, by flame and flameless methods of atomic absorption spectrometry and flame emission spectrometry. The range of products tested included whole blood, red cells, plasma, normal serum albumin, antihemophilic factor, and other products derived from blood; allergenic extracts including honey bee venom and house dust allergenic extracts; vaccines such as measles virus vaccine and typhoid vaccine; and tetanus toxoid. The metal concentrations found in the majority of these products were low or undetectable. The metal levels varied from manufacturer to manufacturer, product and lot-to-lot of the same manufacturer's products. House dust allergenic extracts had the highest concentrations of arsenic (2.4 ppm), cadmium (0.28 ppm), chromium (0.6 ppm) and lead (1.5 ppm) found in the study. A high zinc concentration (24 ppm) in an immune serum globulin was attributed to the zinc-containing rubber stopper in contact with the product. A range of 0.36-3.30 ppm aluminum was found for seven 25% normal serum albumin samples from seven manufacturers. Values of 8.2, 17 and 18 ppm aluminum were found in one manufacturer's 25% normal serum albumin. These aluminum values appeared to be the result of an anomaly in this manufacturer's production that has not been repeated to date.

Development of a soft-soldering system for aluminum

NASA Astrophysics Data System (ADS)

Falke, W. L.; Lee, A. Y.; Neumeier, L. A.

1983-03-01

The method employs application of a thin nickel copper alloy coating to the substrate, which enables the tin lead solders to wet readily and spread over the areas to be joined. The aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied, with an electroless zincate solution. The nickel copper alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloys coatings. The coated areas can then be readily joined with conventional tin lead solders and fluxs. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft solder magnesium alloys.

Mass loading of selected major and trace elements in Lake Fork Creek near Leadville, Colorado, September-October 2001

USGS Publications Warehouse

Walton-Day, Katherine; Flynn, Jennifer L.; Kimball, Briant A.; Runkel, Robert L.

2005-01-01

A mass-loading study of Lake Fork Creek of the Arkansas River between Sugarloaf Dam and the mouth was completed in September-October 2001 to help ascertain the following: (1) variation of pH and aqueous constituent concentrations (calcium, sulfate, alkalinity, aluminum, cadmium, copper, iron, manganese, lead, and zinc) and their relation to toxicity standards along the study reach; (2) location and magnitude of sources of metal loading to Lake Fork Creek; (3) amount and locations of metal attenuation; (4) the effect of streamside wetlands on metal transport from contributing mine tunnels; and (5) the effect of organic-rich inflow from the Leadville National Fish Hatchery on water quality in Lake Fork Creek. The study was done in cooperation with the Bureau of Land Management, U.S. Department of Agriculture Forest Service, and U.S. Fish and Wildlife Service. Constituent concentrations and pH showed variable patterns over the study reach. Hardness-based acute and chronic toxicity standards were exceeded for some inflows and some constituents. However, stream concentrations did not exceed standards except for zinc starting in the upper parts of the study reach and extending to just downstream from the inflow from the Leadville National Fish Hatchery. Dilution from that inflow lowered stream zinc concentrations to less than acute and chronic toxicity standards. The uppermost 800 meters of the study reach that contained inflow from the Bartlett, Dinero, and Nelson mine tunnels and the Dinero wetland was the greatest source of loading for manganese and zinc. A middle section of the study reach that extended approximately 2 kilometers upstream from the National Fish Hatchery inflow to just downstream from that inflow was the largest source of aluminum, copper, iron, and lead loading. The loading was partially from the National Fish Hatchery inflow but also from unknown sources upstream from that inflow, possibly ground water. The largest sources for calcium and sulfate load to the stream were the parts of the study reach containing inflow from the tribu-taries Halfmoon Creek (calcium) and Willow Creek (sulfate). The Arkansas River and its tributaries upstream from Lake Fork Creek were the source of most of the calcium (70 percent), sulfate (82 percent), manganese (77 percent), lead (78 percent), and zinc (95 percent) loads in the Arkansas River downstream from the Lake Fork confluence. In contrast, Lake Fork Creek was the major source of aluminum (68 percent), copper (65 percent), and iron (87 percent) loads to the Arkansas River downstream from the confluence. Attenuation was not important for calcium, sulfate, or iron. However, other metals loads were reduced up to 81 percent over the study reach (aluminum, 25 percent; copper, 20 percent; manganese, 81 percent; lead, 30 percent; zinc, 72 percent). Metal attenuation in the stream occurred primarily in three locations (1) the irrigation diversion ditch; (2) the beaver pond complex extending from upstream from the Colorado Gulch inflow to just downstream from that inflow; and (3) the stream reach that included the inflow from Willow Creek. The most likely attenuation mechanism is precipitation of metal oxides and hydroxides (primarily manganese), and sorption or coprecipitation of trace elements with the precipitating phase. A mass-balance calculation indicated that the wetland between the Dinero Tunnel and Lake Fork Creek removed iron, had little effect on zinc mass load, and was a source for, or was releasing, aluminum and manganese. In contrast, the wetland that occurred between the Siwatch Tunnel and Lake Fork Creek removed aluminum, iron, manganese, and zinc from the tunnel drainage before it entered the creek. Inflow from the National Fish Hatchery increased dissolved organic carbon concentrations in Lake Fork Creek and slightly changed the composition of the dissolved organic carbon. However, dissolved organic carbon loads increased in the stream reach downs

Modern steels for light automobiles (review)

NASA Astrophysics Data System (ADS)

Tikhonov, A. K.

1994-10-01

The article considers the directions of work at VAZ together with metallurgists of the CIS for creating highly efficient economically-alloyed and microalloyed steels; highly ductile forged steels with improved corrosion resistance coated with zinc and with good stamping, welding, and painting capacity. Steels are created for petrol tanks with aluminum-zinc coatings instead of lead, and new heat and corrosion-resistant steels are developed for automobile exhaust gas systems.

Structure and Corrosion Behavior of Arc-Sprayed Zn-Al Coatings on Ductile Iron Substrate

NASA Astrophysics Data System (ADS)

Bonabi, Salar Fatoureh; Ashrafizadeh, Fakhreddin; Sanati, Alireza; Nahvi, Saied Mehran

2018-02-01

In this research, four coatings including pure zinc, pure aluminum, a double-layered coating of zinc and aluminum, and a coating produced by simultaneous deposition of zinc and aluminum were deposited on a cast iron substrate using electric arc-spraying technique. The coatings were characterized by XRD, SEM and EDS map and spot analyses. Adhesion strength of the coatings was evaluated by three-point bending tests, where double-layered coating indicated the lowest bending angle among the specimens, with detection of cracks at the coating-substrate interface. Coatings produced by simultaneous deposition of zinc and aluminum possessed a relatively uniform distribution of both metals. In order to evaluate the corrosion behavior of the coatings, cyclic polarization and salt spray tests were conducted. Accordingly, pure aluminum coating showed susceptibility to pitting corrosion and other coatings underwent uniform corrosion. For double-layered coating, SEM micrographs revealed zinc corrosion products as flaky particles in the pores formed by pitting on the surface, an indication of penetration of corrosion products from the lower layer (zinc) to the top layer (aluminum). All coatings experienced higher negative corrosion potentials than the iron substrate, indicative of their sacrificial behavior.

The Properties of Fluorine, Oxygen Bifluoride, and Chlorine Trifluoride

DTIC Science & Technology

1949-09-06

they should be of forg€;d steel. Welded joints are excellent provided the welds are slag -free. Cast iron or any ether material containing silica cannot...400°C brilliant light Manganese powder form; 500°C formation of fluoride with glowing Zinc Cadmium powder form; heating glowing and flashing...reaction upon heating Magnesium at first, no reaction; explosive reaction Aluminum after ignition with carbon Zinc TV „ 1X11 Lead Cupfier L

40 CFR 467.15 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... aluminum rolled with neat oils Chromium 0.036 0.015 Cyanide 0.024 0.010 Zinc 0.119 0.050 TTO 0.057 Oil and... off-lbs) of aluminum rolled with neat oils Chromium 0.025 0.010 Cyanide 0.016 0.007 Zinc 0.081 0.034... (lb/million off-lbs) of aluminum cast Chromium 0.00086 0.00035 Cyanide 0.00057 0.00024 Zinc 0.0029 0...

REGENERATION OF REACTOR FUEL ELEMENTS

DOEpatents

Lyon, W.L.

1960-04-01

A process is described for concentrating uranium and/or plutonium metal in aluminum alloys in which the actinide content was partially consumed by neutron bombardinent. Two embodiments are claimed: Either the alloy is heated, together with zinc chloride to at least 1000 deg C whereby some aluminum, in the form of aluminum chloride, and any zinc formed volatilize; or else aluminum fluoride is added and reacted at 800 to 1000 deg O and substmospheric pressure whereby pant of the aluminum volatilizes and aluminum subfluoride.

Trace elements in fruit juices.

PubMed

Bragança, Victor Luiz Cordoba; Melnikov, Petr; Zanoni, Lourdes Z

2012-05-01

Fruit juices are widely consumed in tropical countries as part of habitual diet. The concentrations of several minerals in these beverages were evaluated. Four commercially available brands of juices were analyzed for cadmium, lead, copper, zinc, aluminum, iron, chromium, manganese, and molybdenum. The levels ranged from 0.02 to 0.08 mg/L for copper, from 0.05 to 0.23 mg/L for zinc, from 0.1 to 0.4 mg/L for aluminum, from 0.02 to 0.45 mg/L for iron, and from 0.01 to 0.22 mg/L for manganese. The levels of cadmium, lead, and chromium in all samples were very low or undetectable. The metal contents of fruit juices depend on a number of factors, including the soil composition, the external conditions during fruit growing and fruit harvesting, as well as on details of the fruit juice manufacturing processes employed. The concentrations of none of the metals in juice samples analyzed exceeded the limits imposed by local legislation.

Aluminum, iron, lead, cadmium, copper, zinc, chromium, magnesium, strontium, and calcium content in bone of end-stage renal failure patients.

PubMed

D'Haese, P C; Couttenye, M M; Lamberts, L V; Elseviers, M M; Goodman, W G; Schrooten, I; Cabrera, W E; De Broe, M E

1999-09-01

Little is known about trace metal alterations in the bones of dialysis patients or whether particular types of renal osteodystrophy are associated with either increased or decreased skeletal concentrations of trace elements. Because these patients are at risk for alterations of trace elements as well as for morbidity from skeletal disorders, we measured trace elements in bone of patients with end-stage renal disease. We analyzed bone biopsies of 100 end-stage renal failure patients enrolled in a hemodialysis program. The trace metal contents of bone biopsies with histological features of either osteomalacia, adynamic bone disease, mixed lesion, normal histology, or hyperparathyroidism were compared with each other and with the trace metal contents of bone of subjects with normal renal function. Trace metals were measured by atomic absorption spectrometry. The concentrations of aluminum, chromium, and cadmium were increased in bone of end-stage renal failure patients. Comparing the trace metal/calcium ratio, significantly higher values were found for the bone chromium/calcium, aluminum/calcium, zinc/calcium, magnesium/calcium, and strontium/calcium ratios. Among types of renal osteodystrophy, increased bone aluminum, lead, and strontium concentrations and strontium/calcium and aluminum/calcium ratios were found in dialysis patients with osteomalacia vs the other types of renal osteodystrophy considered as one group. Moreover, the concentrations of several trace elements in bone were significantly correlated with each other. Bone aluminum was correlated with the time on dialysis, whereas bone iron, aluminum, magnesium, and strontium tended to be associated with patient age. Bone trace metal concentrations did not depend on vitamin D intake nor on the patients' gender. The concentration of several trace elements in bone of end-stage renal failure patients is disturbed, and some of the trace metals under study might share pathways of absorption, distribution, and accumulation. The clinical significance of the increased/decreased concentrations of several trace elements other than aluminum in bone of dialysis patients deserves further investigation.

Adverse health effects in Canada geese (Branta canadensis) associated with waste from zinc and lead mines in the Tri-State Mining District (Kansas, Oklahoma, and Missouri, USA).

PubMed

van der Merwe, Deon; Carpenter, James W; Nietfeld, Jerome C; Miesner, John F

2011-07-01

Lead and zinc poisoning have been recorded in a variety of bird species, including migrating waterfowl such as Canada Geese (Branta canadensis), at sites contaminated with mine waste from lead and zinc mines in the Tri-State Mining District, Kansas, Oklahoma, and Missouri, USA. The adverse health impacts from mine waste on these birds may, however, be more extensive than is apparent from incidental reports of clinical disease. To characterize health impacts from mine waste on Canada Geese that do not have observable signs of poisoning, four to eight apparently healthy birds per site were collected from four contaminated sites and an uncontaminated reference site, and examined for physical and physiologic evidence of metals poisoning. Tissue concentrations of silver, aluminum, arsenic, barium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, nickel, lead, selenium, thallium, vanadium, and zinc were determined by inductively coupled plasma mass spectroscopy. Adverse health effects due to lead were characterized by assessing blood δ-aminolevulinic acid dehydratase (ALAD) enzyme activity. Adverse effects associated with zinc poisoning were determined from histologic examination of pancreas tissues. Elevated tissue lead concentrations and inhibited blood ALAD enzyme activities were consistently found in birds at all contaminated sites. Histopathologic signs of zinc poisoning, including fibrosis and vacuolization, were associated with elevated pancreatic zinc concentrations at one of the study sites. Adverse health effects associated with other analyzed elements, or tissue concentrations indicating potentially toxic exposure levels to these elements, were not observed.

Flow studies for recycling metal commodities in the United States [Chapters A-M : gold, platinum, chromium, zinc, magnesium, lead, iron, manganese, columbium (niobium), tantalum, tin, molybdenum, and cobalt

USGS Publications Warehouse

Sibley, Scott F.

2004-01-01

USGS Circular 1196, 'Flow Studies for Recycling Metal Commodities in the United States,' presents the results of flow studies for recycling 26 metal commodities, from aluminum to zinc. These metals are a key component of the U.S. economy. Overall, recycling accounts for more than half of the U.S. metal supply by weight and roughly 40 percent by value.

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2012 CFR

2012-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2011 CFR

2011-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2014 CFR

2014-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2013 CFR

2013-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

Zinc alloy enhances strength and creep resistance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Machler, M.

1996-10-01

A family of high-performance ternary zinc-copper-aluminum alloys has been developed that provides higher strength, hardness, and creep resistance than the traditional zinc-aluminum alloys Zamak 3, Zamak 5, and ZA-8. Designated ACuZinc, mechanical properties comparable to those of more expensive materials make it suitable for high-load applications and those at elevated temperatures. This article describes the alloy`s composition, properties, and historical development.

URANIUM COMPOSITIONS

DOEpatents

Allen, N.P.; Grogan, J.D.

1959-05-12

This patent relates to high purity uranium alloys characterized by improved stability to thermal cycling and low thermal neutron absorption. The high purity uranium alloy contains less than 0.1 per cent by weight in total amount of any ore or more of the elements such as aluminum, silicon, phosphorous, tin, lead, bismuth, niobium, and zinc.

40 CFR 464.15 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Aluminum Casting... existing sources. (a) Casting Cleaning Operations. PSES Pollutant or pollutant property Maximum for any 1....0771 0.0421 Lead (T) 0.0791 0.039 Zinc (T) 0.114 0.0431 (b) Casting Quench Operation. PSES Pollutant or...

40 CFR 467.12 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... rolled with neat oils Chromium 0.0360 0.0147 Cyanide 0.0237 0.0098 Zinc 0.119 0.0498 Aluminum 0.525 0.257... aluminum rolled with neat oils Chromium 0.0244 0.010 Cyanide 0.0161 0.0067 Zinc 0.0808 0.0338 Aluminum 0... off-lbs) of aluminum sheet cast by continuous methods Chromium 0.00086 0.00035 Cyanide 0.00057 0.00024...

40 CFR 467.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

.../million off-lbs) of aluminum extruded Chromium 0.15 0.061 Cyanide 0.098 0.041 Zinc 0.49 0.21 Aluminum 2.19... Chromium 0.65 0.27 Cyanide 0.43 0.18 Zinc 2.16 0.90 Aluminum 9.51 4.73 Subpart C Direct Chill Casting... Maximum for monthly average mg/off-kg (lb/million off-lbs) of aluminum cast Chromium 0.59 0.24 Cyanide 0...

The Corrosion Protection of 2219-T87 Aluminum by Organic and Inorganic Zinc-Rich Primers

NASA Technical Reports Server (NTRS)

Danford, M. D.; Mendrek, M. J.; Walsh, D. W.

1995-01-01

The behavior of zinc-rich primer-coated 2219-T87 aluminum in a 3.5-percent Na-Cl was investigated using electrochemical techniques. The alternating current (ac) method of electrochemical impedance spectroscopy (EIS), in the frequency range of 0.001 to 40,000 Hz, and the direct current (dc) method of polarization resistance (PR) were used to evaluate the characteristics of an organic, epoxy zinc-rich primer and an inorganic, ethyl silicate zinc-rich primer. A dc electrochemical galvanic corrosion test was also used to determine the corrosion current of each zinc-rich primer anode coupled to a 2219-T87 aluminum cathode. Duration of the EIS/PR and galvanic testing was 21 days and 24 h, respectively. The galvanic test results demonstrated a very high galvanic current between the aluminum cathode and both zinc-rich primer anodes (37.9 pA/CM2 and 23.7 pA/CM2 for the organic and inorganic primers, respectively). The PR results demonstrated a much higher corrosion rate of the zinc in the inorganic primer than in the organic primer, due primarily to the higher porosity in the former. Based on this investigation, the inorganic zinc-rich primer appears to provide superior galvanic protection and is recommended for additional study for application in the solid rocket booster aft skirt.

The corrosion protection of 2219-T87 aluminum by organic and inorganic zinc-rich primers

NASA Technical Reports Server (NTRS)

Danford, M. D.; Mendrek, M. J.; Walsh, D. W.

1995-01-01

The behavior of zinc-rich primer-coated 2219-T87 aluminum in a 3.5-percent Na-Cl was investigated using electrochemical techniques. The alternating current (ac) method of electro-chemical impedance spectroscopy (EIS), in the frequency range of 0.001 to 40,000 Hz, and the direct current (dc) method of polarization resistance (PR) were used to evaluate the characteristics of an organic, epoxy zinc-rich primer and an inorganic, ethyl silicate zinc-rich primer. A dc electrochemical galvanic corrosion test was also used to determine the corrosion current of each zinc-rich primer anode coupled to a 2219-T87 aluminum cathode. Duration of the EIS/PR and galvanic testing was 21 days and 24 h, respectively. the galvanic test results demonstrated a very high galvanic current between the aluminum cathode and both zinc-rich primer anodes (37.9 micro A/cm(exp 2) and 23.7 micro A/cm(exp 2) for the organic and inorganic primers, respectively). The PR results demonstrated a much higher corrosion rate of the zinc in the inorganic primer than in the organic primer, due primarily to the higher porosity in the former. Based on this investigation, the inorganic zinc-rich primer appears to provide superior galvanic protection and is recommended for additional study for application in the solid rocket booster aft skirt.

Soil Chemistry Still Affected 23 Years After Large Application of Fluidized Bed Material

USDA-ARS?s Scientific Manuscript database

This study was conducted to assess the movement of arsenic, aluminum, calcium, copper, iron, lead, magnesium, manganese, mercury and zinc in an old apple (Malus domestica Borkh) orchard that received a one time application of 36 kg/ m2 of fluidized bed combustion material (FBCM) 23 years earlier. S...

Composition of the edible portion of raw (fresh or frozen) crustaceans, finfish, and mollusks. III. Microelements. [Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sidwell, V.D.; Loomis, A.L.; Loomis, K.J.

1978-09-01

This report summarizes data from 224 publications referring to the microelements found in the flesh of commonly eaten seafoods. These microelements are: copper, iron, zinc, iodine, manganese, mercury, organic mercury, lead arsenic, fluorine, silver, cadmium, cobalt, selenium, chromium, vanadium, tin, aluminum, nickel, barium, and molybdenum.

Tunable infrared absorption and visible transparency of colloidal aluminum-doped zinc oxide nanocrystals.

PubMed

Buonsanti, Raffaella; Llordes, Anna; Aloni, Shaul; Helms, Brett A; Milliron, Delia J

2011-11-09

Plasmonic nanocrystals have been attracting a lot of attention both for fundamental studies and different applications, from sensing to imaging and optoelectronic devices. Transparent conductive oxides represent an interesting class of plasmonic materials in addition to metals and vacancy-doped semiconductor quantum dots. Herein, we report a rational synthetic strategy of high-quality colloidal aluminum-doped zinc oxide nanocrystals. The presence of substitutional aluminum in the zinc oxide lattice accompanied by the generation of free electrons is proved for the first time by tunable surface plasmon absorption in the infrared region both in solution and in thin films.

A comparison of corrosion inhibition of magnesium aluminum and zinc aluminum vanadate intercalated layered double hydroxides on magnesium alloys

NASA Astrophysics Data System (ADS)

Guo, Lian; Zhang, Fen; Lu, Jun-Cai; Zeng, Rong-Chang; Li, Shuo-Qi; Song, Liang; Zeng, Jian-Min

2018-04-01

The magnesium aluminum and zinc aluminum layered double hydroxides intercalated with NO3 -(MgAl-NO3-LDH and ZnAl-NO3-LDH) were prepared by the coprecipitation method, and the magnesium aluminum and the zinc aluminum layered double hydroxides intercalated with VO x -(MgAl-VO x -LDH and ZnAl-VO x -LDH) were prepared by the anion-exchange method. Morphologies, microstructures and chemical compositions of LDHs were investigated by SEM, EDS, XRD, FTIR, Raman and TG analyses. The immersion tests were carried to determine the corrosion inhibition properties of MgAl-VO x -LDH and ZnAl-VO x -LDH on AZ31 Mg alloys. The results showed that ZnAl-VO x -LDH possesses the best anion-exchange and inhibition abilities. The influence of treatment parameters on microstructures of LDHs were discussed. Additionally, an inhibition mechanism for ZnAl-VO x -LDH on the AZ31 magnesium alloy was proposed and discussed.

Effect of Zinc Coatings on Joint Properties and Interfacial Reactions in Aluminum to Steel Ultrasonic Spot Welding

NASA Astrophysics Data System (ADS)

Haddadi, F.; Strong, D.; Prangnell, P. B.

2012-03-01

Dissimilar joining of aluminum to steel sheet in multimaterial automotive structures is an important potential application of ultrasonic spot welding (USW). Here, the weldability of different zinc-coated steels with aluminum is discussed, using a 2.5-kW USW welder. Results show that soft hot-dipped zinc (DX56-Z)-coated steel results in better weld performance than hard (galv-annealed) zinc coatings (DX53-ZF). For Al to hard galv-annealed-coated steel welds, lap shear strengths reached a maximum of ~80% of the strength of an Al-Al joint after a 1.0 s welding time. In comparison, welds between Al6111-T4 and hot dipped soft zinc-coated steel took longer to achieve the same maximum strength, but nearly matched the Al-Al joint properties. The reasons for these different behaviors are discussed in terms of the interfacial reactions between the weld members.

Performances of metal concentrations from three permeable pavement infiltrates.

PubMed

Liu, Jiayu; Borst, Michael

2018-06-01

The U.S. Environmental Protection Agency constructed a 4000-m 2 parking lot in Edison, New Jersey in 2009. The parking lot is surfaced with three permeable pavements [permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA)]. Samples of each permeable pavement infiltrate, surface runoff from traditional asphalt, and rainwater were analyzed in duplicate for 22 metals (total and dissolved) for 6 years. In more than 99% of the samples, the concentration of barium, chromium, copper, manganese, nickel and zinc, and in 60%-90% of the samples, the concentration of arsenic, cadmium, lead, and antimony in infiltrates from all three permeable pavements met both the groundwater effluent limitations (GEL) and maximum contaminant levels (MCL). The concentration of aluminum (50%) and iron (93%) in PICP infiltrates samples exceed the GELs; however, the concentration in more than 90% samples PA and PC infiltrates met the GELs. No measurable difference in metal concentrations was found from the five sources for arsenic, cadmium, lead, antimony, and tin. Large concentrations of eleven metals, including manganese, copper, aluminum, iron, calcium, magnesium, sodium, potassium, silica, strontium and vanadium, were detected in surface runoff than the rainwater. Chromium, copper, manganese, nickel, aluminum, zinc, iron and magnesium concentrations in PICP infiltrates; calcium, barium, and strontium concentrations in PA infiltrates; sodium, potassium and vanadium concentrations in PC infiltrates were statistically larger than the other two permeable pavement infiltrates. Published by Elsevier Ltd.

Selected Metals in Sediments and Streams in the Oklahoma Part of the Tri-State Mining District, 2000-2006

USGS Publications Warehouse

Andrews, William J.; Becker, Mark F.; Mashburn, Shana L.; Smith, S. Jerrod

2009-01-01

The abandoned Tri-State mining district includes 1,188 square miles in northeastern Oklahoma, southeastern Kansas, and southwestern Missouri. The most productive part of the Tri-State mining district was the 40-square mile part in Oklahoma, commonly referred to as 'the Picher mining district' in north-central Ottawa County, Oklahoma. The Oklahoma part of the Tri-State mining district was a primary producing area of lead and zinc in the United States during the first half of the 20th century. Sulfide minerals of cadmium, iron, lead, and zinc that remained in flooded underground mine workings and in mine tailings on the land surface oxidized and dissolved with time, forming a variety of oxide, hydroxide, and hydroxycarbonate metallic minerals on the land surface and in streams that drain the district. Metals in water and sediments in streams draining the mining district can potentially impair the habitat and health of many forms of aquatic and terrestrial life. Lakebed, streambed and floodplain sediments and/or stream water were sampled at 30 sites in the Oklahoma part of the Tri-State mining district by the U.S. Geological Survey and the Oklahoma Department of Environmental Quality from 2000 to 2006 in cooperation with the U.S. Environmental Protection Agency, and the Quapaw and Seneca-Cayuga Tribes of Oklahoma. Aluminum and iron concentrations of several thousand milligrams per kilogram were measured in sediments collected from the upstream end of Grand Lake O' the Cherokees. Manganese and zinc concentrations in those sediments were several hundred milligrams per kilogram. Lead and cadmium concentrations in those sediments were about 10 percent and 0.1 percent of zinc concentrations, respectively. Sediment cores collected in a transect across the floodplain of Tar Creek near Miami, Oklahoma, in 2004 had similar or greater concentrations of those metals than sediment cores collected at the upstream end of Grand Lake O' the Cherokees. The greatest concentrations of cadmium, iron, lead, and zinc were detected in sediments beneath an intermittent tributary to Tar Creek, a slough which drains mined areas near Commerce, Oklahoma. In surface water, aluminum and iron concentrations were greatest in the Neosho River, perhaps a result of runoff from areas underlain by shales. The greatest aqueous concentrations of cadmium, lead, manganese, and zinc were measured in water from Tar Creek, the primary small stream draining the Picher mining district with the largest proportion of mined area. Water from the Spring River had greater zinc concentrations than water from the Neosho River, perhaps as a result of a greater proportion of mined area in the Spring River Basin. Dissolved metals concentrations were generally much less than total metals concentrations, except for manganese and zinc at sites on Tar Creek, where seepage of ground water from the mine workings, saturated mine tailings, and/or metalliferous streambed sediments may be sources of these dissolved metals. Iron and lead concentrations generally decreased with increasing streamflow in upstream reaches of Tar Creek, indicating dilution of metals-rich ground water by runoff. Farther downstream in Tar Creek, and in the Neosho and Spring Rivers, metals concentrations tended to increase with increasing streamflow, indicating that most metals in these parts of these streams were associated with runoff and re-suspension of metals precipitated as oxide, hydroxide, and hydroxycarbonate minerals on land surface and streambeds. Estimated total aluminum, cadmium, iron, manganese, and zinc loads generally were greatest in water from the Neosho and Spring Rivers, primarily because of comparatively large streamflows in those rivers. Slight increases in metal loads in the downstream directions on those rivers indicated contributions of metals from inflows of small tributaries such as Tar Creek and from runoff.

Effects of acid-mine wastes on aquatic ecosystems

Treesearch

John David Parsons

1976-01-01

The Cedar Creek Basin (39th N parallel 92nd W meridian) was studied for the period June 1952 through August 1954 to observe the effects of both continuous and periodic acid effluent flows on aquatic communities. The acid strip-mine effluent contained ferric and ferrous iron, copper, lead, zinc, aluminum, magnesium, titratable acid, and elevated hydrogen ion...

A compound crystal with film scintillator for electron detection

NASA Astrophysics Data System (ADS)

McKinney, George; McDonnald, Warren; Tzolov, Marian

2015-03-01

Yttrium Aluminum Garnets (YAG) and Yttrium Aluminum Perovskite (YAP) are widely used as electron detectors. This application requires a top conducting layer which hinders their application at low electron energies. We have developed a layer of zinc tungstate which delivers conductivity large enough to prevent charging while still being an efficient scintillator. For better coupling between the two systems we have studied their optical properties. Ce doping is an essential element in YAP and YAG in order for them to be efficient scintillators. We have studied the Ce content and we show that higher Ce content leads to reabsorption in the YAP scintillators. These details were revealed by using photoluminescence emission and excitation spectroscopy. The absorption spectrum for the YAG scintillators coincides with the excitation for the main emission lines. The optical studies of the zinc tungstate films and a single crystal have shown that the films are more efficient light emitters. We have integrated the zinc tungstate films with YAG scintillators and we will report on the performance of this compound scintillator. It is expected that it will perform well at low and high electron energies, which makes it a very cost effective platform for electron detectors.

Recent trends in the nonfuel minerals industry of Iran

USGS Publications Warehouse

Hastorun, Sinan; Renaud, Karine M.; Lederer, Graham W.

2016-07-11

The U.S. Geological Survey estimated that Iran held globally significant reserves of feldspar (2d largest in the world), barite (5th largest), gypsum (5th largest), fluorspar (8th largest), and iron ore (10th largest). The Government of Iran claimed to also have significant reserves of chromium, copper, gold, manganese, phosphate rock, and zinc. In 2014, Iran was the second-leading producer of gypsum and the sixth-leading producer of barite, with 6.1 percent and 3.6 percent of world output, respectively. Iran was also the world’s 7th-leading producer of cement, feldspar, and fluorspar; 8th-leading producer of bentonite; 9th-leading producer of molybdenum; 11th-leading producer of iron ore; and 14th-leading producer of crude steel. The Government of Iran plans to quadruple the output of aluminum, copper cathode, direct-reduced iron, and iron ore pellets; triple that of crude steel and gold; and double that of cement, pig iron, and zinc by 2025. It also plans to double the contribution of mining and to quadruple that of mineral processing to the national economy in the next decade. In order to achieve these major goals, the construction and expansion of several mines and mineral facilities are planned or under development. Whether Iran’s annual mineral production increases as rapidly as envisioned by the Government will depend largely on the amount of foreign investment into the minerals industry; integration of modern technology into mineral facilities; and availability of energy to aluminum, copper, and steel plants at competitive prices to international investors.

75 FR 55745 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Preliminary Results...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-14

... with corrosion-resistant metals such as zinc, aluminum, or zinc-, aluminum-, nickel- or iron-based... medium-sized company, or any large company that is not included in the five largest conglomerates based... property tax based on the location of its manufacturing facilities, Suncheon Works, in the Yulchon...

40 CFR 466.33 - New source performance standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS PORCELAIN ENAMELING POINT SOURCE CATEGORY Aluminum Basis Material Subcategory § 466....11 Nickel 5.35 0.69 3.60 0.47 Zinc 9.92 1.29 4.09 0.53 Aluminum 29.46 3.82 12.06 1.56 Iron 11.96 1.55... 0.03 0.18 0.20 Nickel 1.10 0.14 0.74 0.10 Zinc 2.03 0.27 0.84 0.11 Aluminum 6.03 0.78 2.47 0.32 Iron...

The efficacy of deferiprone on tissues aluminum removal and copper, zinc, manganese level in rabbits.

PubMed

Liu, Ping; Yao, Yu-Na; Wu, Shi-De; Dong, Huai-Jun; Feng, Guo-Chang; Yuan, Xiao-Yan

2005-08-01

The effect of 1,2-dimethyl-3-hydroxypyrid-4-one [deferiprone (DE)] on aluminum mobilization and elimination from tissues and serum as well as the influence on the excretion of trace elements, copper, zinc and manganese in rabbits was investigated. Sixteen New Zealand rabbits were randomly divided into three groups: control, Al-only and Al+DE. The Al-only and Al+DE animals received injections of Al2(SO43.18H2O 600 micromol Al/kg 5 days per week for 3 weeks. One week after the last Al injection the Al+DE rabbits were given deferiprone 750 micromol/kg/day intragastrically for 2 weeks. At the 42nd day the animals were sacrificed and the organs were taken and digested. Blood was taken from the ear artery three times (at the initiation of the experiment, before and after deferiprone administration). The aluminum and copper, zinc, manganese were determined by atomic absorption spectrophotometry. Our results showed that deferiprone could highly mobilize aluminum stores from tissues. At the end of experiment the aluminum contents of bone, kidney, liver and brain in Al+DE were significantly lower than that in Al-only rabbits. The copper, zinc, manganese contents were not affected by deferiprone administration.

77 FR 13093 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

...-resistant metals such as zinc, aluminum, or zinc-, aluminum-, nickel- or iron-based alloys, whether or not... Special Taxation Act (RSTA) Article 26 II. Programs That Provided No Benefits During the POR A. Research and Development Grants Under the Industrial Development Act (IDA) B. Research and Development Grants...

Strategic Minerals: U.S. Alternatives

DTIC Science & Technology

1990-02-01

Titanium -Bearing Slag, and Vanadium 267 U2. Mobilization Plans: Excerpt of a 1987 Letter, Deputy Sec- retary of Defense William H. Taft IV to Speaker of...Program Minerals Availability Appraisals for Asbestos, Co- balt, Fluorspar, Mercury, Molybdenum, Lead, Zinc, Titanium , and Tungsten Mineral Industry...intermediate products necessary for the production of aluminum and titanium . In trade Australia’s mineral exports account for over one-third of its

Alternatives To Cadmium Plated Military Connectors

DTIC Science & Technology

2011-08-30

from Feb 2011 Asets Defense conference  Amphenol Aerospace Operations report. 9/21/2011 10 Chromate finish  Hexavalent chrome was targeted by DOD...Fluorocarbon Zinc-Nickel Pure Dense Aluminum  Zinc-Nickel and Aluminum currently contain hexavalent chromate. Nickel-Fluorocarbon requires no...to lack of available drop in replacements, but this will change as alternatives become available.  Trivalent chrome and other non- chrome

Chemical analyses of water samples from the Picher mining area, northeast Oklahoma and southeast Kansas

USGS Publications Warehouse

Parkhurst, David L.

1987-01-01

Chemical analyses are presented for 169 water samples from Tar Creek drainage and the Picher lead-zinc mining area of northeast Oklahoma and southeast Kansas. Water samples were taken from November 1983 through February 1986 from the abandoned mines, from points of mine-water discharge, and from surface-water locations upstream and downstream from mine discharge area. The pH, temperature, alkalinity, dissolved oxygen, and specific conductance were measured in the field. Laboratory analyses routinely included the major ions plus aluminum, cadmium, copper, iron, lead, manganese, nickel, and zinc. Non-routine analyses of dissolved gases and tritium are presented. Stable carbon-isotope ratios for 11 mine-water samples and three carbonate-rock samples are reported. Miscellaneous stream-discharge measurements made at the time of sampling or taken from gaging-station records are included in the report.

Hydrothermal synthesis and characterization of hybrid Al/ZnO-GO composite for significant photodegrdation of dyes

NASA Astrophysics Data System (ADS)

Lellala, Kashinath; Namratha, K.; Sudhakar, K.; Byrappa, K.

2016-05-01

In the present work, undoped and doped Aluminum/Zinc Oxide - graphene oxide (Al/ZnO-GO) nanocomposite have been successfully synthesized by hydrothermal method from zinc acetate and aluminum nitrate solutions without using of any surfactant/stabilizing agents. The results show that the composites of GO nanosheets are decorated densely by Al/ZnO nanoparticles, which displays a good morphology and blend between GO and Al/ZnO. Hybrid composites exhibit an enhanced photocatalytic performance in reduction of dyes under UV-Vis radiation better than bare ZnO-GO and GO for methylene blue dye. The hydrothermal method leads to particles with a higher crystalline due to ambient temperature of the reaction and autogenously pressure conditions, which alters the phases and crystallizations of the nanocomposite. The optical band gap is narrowed to lower energy values due to controlled addition of aluminum and GO in the composite. The improved optical property in Al-doped ZnO flower decorated on GO can be attributed to the decrease in oxygen deficiency after Al doping. XRD, FTIR, UV-Vis spectroscopy, Raman, and Field Emission Scanning Electron Microscopy characterized the effects of Al doping on the structural characteristics and optical properties on the ZnO-GO.

Hydrothermal synthesis and characterization of hybrid Al/ZnO-GO composite for significant photodegrdation of dyes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lellala, Kashinath; Namratha, K.; Byrappa, K., E-mail: kashinathlellala@gmail.com, E-mail: kbyrappa@gmail.com

In the present work, undoped and doped Aluminum/Zinc Oxide - graphene oxide (Al/ZnO-GO) nanocomposite have been successfully synthesized by hydrothermal method from zinc acetate and aluminum nitrate solutions without using of any surfactant/stabilizing agents. The results show that the composites of GO nanosheets are decorated densely by Al/ZnO nanoparticles, which displays a good morphology and blend between GO and Al/ZnO. Hybrid composites exhibit an enhanced photocatalytic performance in reduction of dyes under UV-Vis radiation better than bare ZnO-GO and GO for methylene blue dye. The hydrothermal method leads to particles with a higher crystalline due to ambient temperature of themore » reaction and autogenously pressure conditions, which alters the phases and crystallizations of the nanocomposite. The optical band gap is narrowed to lower energy values due to controlled addition of aluminum and GO in the composite. The improved optical property in Al-doped ZnO flower decorated on GO can be attributed to the decrease in oxygen deficiency after Al doping. XRD, FTIR, UV-Vis spectroscopy, Raman, and Field Emission Scanning Electron Microscopy characterized the effects of Al doping on the structural characteristics and optical properties on the ZnO-GO.« less

Characterization of anthropogenic and natural sources of acid rock drainage at the Cinnamon Gulch abandoned mine land inventory site, Summit County, Colorado

USGS Publications Warehouse

Bird, D.A.

2003-01-01

Colorado's Cinnamon Gulch releases acid rock drainage (ARD) from anthropogenic and natural sources. In 2001, the total discharge from Cinnamon Gulch was measured at 1.02 cfs (29 L/s) at base flow and 4.3 cfs (122 L/s) at high flow (spring runoff). At base flow, natural sources account for 98% of the discharge from the watershed, and about 96% of the chemical loading. At high flow, natural sources contribute 96% of discharge and 92 to 95% of chemical loading. The pH is acidic throughout the Cinnamon Gulch watershed, ranging from 2.9 to 5.4. At baseflow, nearly all of the trace metals analyzed in the 18 samples exceeded state hardness-dependent water quality standards for aquatic life. Maximum dissolved concentrations of selected constituents included 16 mg/ L aluminum, 15 mg/L manganese, 40 mg/L iron, 2 mg/L copper, 560 ??g/L lead, 8.4 mg/L zinc, and 300 mg/L sulfate. Average dissolved concentrations of selected metals at baseflow were 5.5 mg/L aluminum, 5.5 mg/L manganese, 14 ??g/L cadmium, 260 ??g/L copper, 82 ??g/L lead, and 2.8 mg/L zinc.

40 CFR 467.46 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... off-lbs) of aluminum forged Chromium 0.019 0.008 Cyanide 0.010 0.004 Zinc 0.051 0.021 TTO 0.035 Oil and grease (alternate monitoring parameter) 0.50 0.50 Subpart D Forging Scrubber Liquor Pollutant or... aluminum forged Chromium 0.035 0.014 Cyanide 0.019 0.008 Zinc 0.096 0.040 TTO 0.065 Oil and grease...

40 CFR 467.16 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Maximum for monthly average mg/off-kg (lb/million off-lbs) of aluminum rolled with neat oils Chromium 0... rolled with neat oils Chromium 0.021 0.009 Cyanide 0.011 0.005 Zinc 0.057 0.024 TTO 0.038 Oil and grease... aluminum cast Chromium 0.00073 0.00029 Cyanide 0.00039 0.00016 Zinc 0.0020 0.00082 TTO 0.0014 Oil and...

Laser Overlap Welding of Zinc-coated Steel on Aluminum Alloy

NASA Astrophysics Data System (ADS)

Kashani, Hamed Tasalloti; Kah, Paul; Martikainen, Jukka

Local reinforcement of aluminum with laser welded patches of zinc-coated steel can effectively contribute to crashworthiness, durability and weight reduction of car body. However, the weld between Zn-coated steel and aluminum is commonly susceptible to defects such as spatter, cavity and crack. The vaporization of Zn is commonly known as the main source of instability in the weld pool and cavity formation, especially in a lap joint configuration. Cracks are mainly due to the brittle intermetallic compounds growing at the weld interface of aluminum and steel. This study provides a review on the main metallurgical and mechanical concerns regarding laser overlap welding of Zn-coated steel on Al-alloy and the methods used by researchers to avoid the weld defects related to the vaporization of Zn and the poor metallurgical compatibility between steel and aluminum.

21 CFR 82.1051 - Lakes (D&C).

Code of Federal Regulations, 2011 CFR

2011-04-01

..., gloss white, clay, titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or... radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium; or (ii) a salt prepared... subpart, by combining such color with the basic radical sodium, potassium, aluminum, barium, calcium...

21 CFR 82.1051 - Lakes (D&C).

Code of Federal Regulations, 2010 CFR

2010-04-01

..., gloss white, clay, titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or... radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium; or (ii) a salt prepared... subpart, by combining such color with the basic radical sodium, potassium, aluminum, barium, calcium...

21 CFR 82.1051 - Lakes (D&C).

Code of Federal Regulations, 2012 CFR

2012-04-01

..., gloss white, clay, titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or... radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium; or (ii) a salt prepared... subpart, by combining such color with the basic radical sodium, potassium, aluminum, barium, calcium...

21 CFR 82.1051 - Lakes (D&C).

Code of Federal Regulations, 2014 CFR

2014-04-01

..., gloss white, clay, titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or... radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium; or (ii) a salt prepared... subpart, by combining such color with the basic radical sodium, potassium, aluminum, barium, calcium...

21 CFR 82.1051 - Lakes (D&C).

Code of Federal Regulations, 2013 CFR

2013-04-01

..., gloss white, clay, titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or... radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium; or (ii) a salt prepared... subpart, by combining such color with the basic radical sodium, potassium, aluminum, barium, calcium...

Investigating the Mechanisms and Potential of Silk Fiber Metallization

DTIC Science & Technology

2013-09-30

in an ALD process, when using the modified metal infiltration process as outlined by Lee et al., the titanium isopropoxide (TIP) precursor...these fibers exhibited >2-fold increase in strain to breakage, and >4.5-fold increase in strength when infiltrated with zinc, titanium , or aluminum...fibers exhibited >2-fold increase in strain to breakage, and >4.5-fold increase in strength when infiltrated with zinc, titanium , or aluminum

Contribution to the aluminum-tin-zinc ternary system

NASA Astrophysics Data System (ADS)

Drápala, J.; Kostiuková, G.; Losertová, M.

2017-11-01

The Sn-Zn-Al alloys are one of significant candidates in the proposal of alternative lead-free solders for higher temperature soldering. This paper deals with the study of the aluminum-tin-zinc system. Twenty Sn-Zn-Al alloys together with six binary Sn-Zn alloys were prepared and studied experimentally. Alloys were prepared from pure Sn, Zn and Al (melting and cooling in a vacuum resistance furnace). The specimens were studied metallographically including the micro-hardness measurements, complete chemical analysis (ICP-AES, OES), X-ray micro-analysis of alloys by SEM and EDX in order to determine the composition and identification of individual phases. Significant temperatures and enthalpies of phase transformations were determined by DTA. After long-term annealing of selected alloys in vacuum followed by quenching the structural and chemical microanalyses of the present phases and their limit concentrations were carried out. The achieved results were compared with the thermodynamic modelling of the ternary Sn-Zn-Al system (computer programs THERMOCALC, MTDATA, PANDAT and databases CALPHAD, COST). Electrical resistivity, density, magnetic susceptibility and wettability of Sn-Zn-Al solders were measured as well.

Improvement of the radiographic method for measurement of effective energy of pulsed X-ray emission from a PF device for different anode's insert materials.

PubMed

Miremad, Seyed Milad; Shirani, Babak

2018-06-01

In this paper, effective energy of pulsed X-Ray emitted from a Mather-type plasma focus device in stored energy of 2.5 kJ with six different anode's insert materials was measured using radiographic method with attenuation filters. Since intensity and energy of X-ray beam were considerably changed with changing the insert material, the method was improved by using different filters simultaneously in all the experiments and selection of the best filter in each experiment according to the appropriate criteria. Effective energy of pulsed X-ray beam was measured 16, 28, 50, 51, 34 and 44 keV when aluminum, copper, zinc, tin, tungsten and lead were used as insert materials, and aluminum, copper, silver, silver, copper and lead were used as filters, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Survey of electrochemical metal winning processes. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaaler, L.E.

1979-03-01

The subject program was undertaken to find electrometallurgical technology that could be developed into energy saving commercial metal winning processes. Metals whose current production processes consume significant energy (excepting copper and aluminum) are magnesium, zinc, lead, chromium, manganese, sodium, and titanium. The technology of these metals, with the exception of titanium, was reviewed. Growth of titanium demand has been too small to justify the installation of an electrolyte process that has been developed. This fact and the uncertainty of estimates of future demand dissuaded us from reviewing titanium technology. Opportunities for developing energy saving processes were found for magnesium, zinc,more » lead, and sodium. Costs for R and D and demonstration plants have been estimated. It appeared that electrolytic methods for chromium and manganese cannot compete energywise or economically with the pyrometallurgical methods of producing the ferroalloys, which are satisfactory for most uses of chromium and manganese.« less

Colloidal infrared reflective and transparent conductive aluminum-doped zinc oxide nanocrystals

DOEpatents

Buonsanti, Raffaella; Milliron, Delia J

2015-02-24

The present invention provides a method of preparing aluminum-doped zinc oxide (AZO) nanocrystals. In an exemplary embodiment, the method includes (1) injecting a precursor mixture of a zinc precursor, an aluminum precursor, an amine, and a fatty acid in a solution of a vicinal diol in a non-coordinating solvent, thereby resulting in a reaction mixture, (2) precipitating the nanocrystals from the reaction mixture, thereby resulting in a final precipitate, and (3) dissolving the final precipitate in an apolar solvent. The present invention also provides a dispersion. In an exemplary embodiment, the dispersion includes (1) nanocrystals that are well separated from each other, where the nanocrystals are coated with surfactants and (2) an apolar solvent where the nanocrystals are suspended in the apolar solvent. The present invention also provides a film. In an exemplary embodiment, the film includes (1) a substrate and (2) nanocrystals that are evenly distributed on the substrate.

Improved corrosion resistance on biodegradable magnesium by zinc and aluminum ion implantation

NASA Astrophysics Data System (ADS)

Xu, Ruizhen; Yang, Xiongbo; Suen, Kai Wong; Wu, Guosong; Li, Penghui; Chu, Paul K.

2012-12-01

Magnesium and its alloys have promising applications as biodegradable materials, and plasma ion implantation can enhance the corrosion resistance by modifying the surface composition. In this study, suitable amounts of zinc and aluminum are plasma-implanted into pure magnesium. The surface composition, phases, and chemical states are determined, and electrochemical tests and electrochemical impedance spectroscopy (EIS) are conducted to investigate the surface corrosion behavior and elucidate the mechanism. The corrosion resistance enhancement after ion implantation is believed to stem from the more compact oxide film composed of magnesium oxide and aluminum oxide as well as the appearance of the β-Mg17Al12 phase.

Electrical properties of aluminum-doped zinc oxide (AZO) nanoparticles synthesized by chemical vapor synthesis.

PubMed

Hartner, Sonja; Ali, Moazzam; Schulz, Christof; Winterer, Markus; Wiggers, Hartmut

2009-11-04

Aluminum-doped zinc oxide nanoparticles have been prepared by chemical vapor synthesis, which facilitates the incorporation of a higher percentage of dopant atoms, far above the thermodynamic solubility limit of aluminum. The electrical properties of aluminum-doped and undoped zinc oxide nanoparticles were investigated by impedance spectroscopy. The impedance is measured under hydrogen and synthetic air between 323 and 673 K. The measurements under hydrogen as well as under synthetic air show transport properties depending on temperature and doping level. Under hydrogen atmosphere, a decreasing conductivity with increasing dopant content is observed, which can be explained by enhanced scattering processes due to an increasing disorder in the nanocrystalline material. The temperature coefficient for the doped samples switches from positive temperature coefficient behavior to negative temperature coefficient behavior with increasing dopant concentration. In the presence of synthetic air, the conductivity firstly increases with increasing dopant content by six orders of magnitude. The origin of the increasing conductivity is the generation of free charge carriers upon dopant incorporation. It reaches its maximum at a concentration of 7.7% of aluminum, and drops for higher doping levels. In all cases, the conductivity under hydrogen is higher than under synthetic air and can be changed reversibly by changing the atmosphere.

NAVAIR Progress in Assessing, Validating and Implementing Non-Chromate Primers (Briefing charts)

DTIC Science & Technology

2011-02-09

logistics for any new coating or coating system NAVAIR Application Areas for Hexavalent Chromium Alternatives: Status Components/ Structure... Hexavalent chromium alternatives Sacrificial Coating Post Treatment MIL-A-8625 Anodize Avionics/ Electronics Magnesium/Titanium Conversion Aluminum Anodizing...Aluminum Pretreatment Type IC Seal Type IIB Seal Type II Seal Phosphating Rinse (Aluminum)Rinse (Steel) Cadmium Zinc-Nickel Aluminum Bonding Chrome

Demonstration and Validation of a Regenerated-Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground Water Quality and Remediation Progress at DoD Sites

DTIC Science & Technology

2007-01-01

ethanol, sodium benzoate , and ethylene diamine tetra-acetic acid (EDTA). Alternatively, the membrane can be purchased dry, but then must be...cleaned in a series of steps that includes soaking and rinsing in deionized water, heated sodium bicarbonate solution, EDTA, and sodium azide solution to...Potassium Chromium Selenium Sodium Copper Vanadium Aluminum Iron Zinc Arsenic Lead Antimony Manganese Anions (1-3 days) Bicarbonate/Alkalinity

An Annotated Bibliography for Cleanup of Hazardous Waste Disposal Sites

DTIC Science & Technology

1982-10-01

H., and Zaidi, T. H. 1981. "The Adsorption Character- istics of Soils and Removal of Cadmium and Nickel from Waste- waters," Water, Air, and Soil Poll... Wabash Avenue, Chicago, IL. Subject: Neutralization. Description: This article describes treatment of acidic wastes such as those from coke plants...greater than 85 percent of the aluminum, barium, cadmium , mercury, nickel, and zinc and from 40 to 70 percent of the chro- mium, copper, lead, and

Emission of PCDD/Fs and dioxin-like PCBs from metallurgy industries in S. Korea.

PubMed

Yu, Byeong-Woon; Jin, Guang-Zhu; Moon, Young-Hoon; Kim, Min-Kwan; Kyoung, Jong-Dai; Chang, Yoon-Seok

2006-01-01

The metallurgy industry and municipal waste incinerators are considered the main sources of polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs) in many countries. This study investigated the emission factors and total emissions of PCDD/Fs and dioxin-like polychlorinated biphenyls (PCBs) emitted from metallurgy industries (including ferrous and nonferrous foundries) in Korea. The toxic equivalency (TEQ) emission factor of PCDD/Fs was the highest for secondary copper production, at 24451 ng I-TEQ/ton. The total estimated emissions of PCDD/Fs from these sources were 35.259 g I-TEQ/yr, comprising 0.088 g I-TEQ/yr from ferrous foundries, 31.713 g I-TEQ/yr from copper production, 1.716 g I-TEQ/yr from lead production, 0.111 g I-TEQ/yr from zinc production, and 1.631 g I-TEQ/yr from aluminum production. The total estimated annual amounts of dioxin-like PCBs emitted from these sources were 13.260 g WHO-TEQ/yr, comprising 0.014 g WHO-TEQ/yr from ferrous foundries, 12.675 g WHO-TEQ/yr from copper production, 0.170 g WHO-TEQ/yr from lead production, 0.017 g WHO-TEQ/yr from zinc production, and 0.384 g WHO-TEQ/yr from aluminum production. The highest emission factor was found for secondary copper smelting, at 9770 ng WHO-TEQ/ton.

76 FR 66684 - Foreign-Trade Zone 29-Louisville, KY, Application for Subzone; North American Stainless...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-27

...) include: fluorospar, molybdenum oxide, ferromanganese, ferrosilicon, ferrosilicon manganese, charge chrome... spent anodes, nickel, unwrought nickel alloys, aluminum, zinc, zinc alloys, manganese metal, titanium...

Zinc oxide varistors and/or resistors

DOEpatents

Arnold, W.D. Jr.; Bond, W.D.; Lauf, R.J.

1993-07-27

Varistors and/or resistors are described that include doped zinc oxide gel microspheres. The doped zinc oxide gel microspheres preferably have from about 60 to about 95% by weight zinc oxide and from about 5 to about 40% by weight dopants based on the weight of the zinc oxide. The dopants are a plurality of dopants selected from silver salts, boron oxide, silicon oxide and hydrons oxides of aluminum, bismuth, cobalt, chromium, manganese, nickel, and antimony.

Zinc oxide varistors and/or resistors

DOEpatents

Arnold, Jr., Wesley D.; Bond, Walter D.; Lauf, Robert J.

1993-01-01

Varistors and/or resistors that includes doped zinc oxide gel microspheres. The doped zinc oxide gel microspheres preferably have from about 60 to about 95% by weight zinc oxide and from about 5 to about 40% by weight dopants based on the weight of the zinc oxide. The dopants are a plurality of dopants selected from silver salts, boron oxide, silicon oxide and hydrons oxides of aluminum, bismuth, cobalt, chromium, manganese, nickel, and antimony.

Metastable Phases of Dross Particles Formed in a Molten Zinc Bath and Prediction of Soluble Aluminum During Galvannealing Processes

NASA Astrophysics Data System (ADS)

Paik, Doo-Jin; Hong, Moon-Hi; Huh, Yoon; Park, Joo Hyun; Chae, Hong-Kook; Park, Seok-Ho; Choun, Si-Youl

2012-06-01

The morphology, chemistry, and crystallographic characteristics of metastable dross particles were identified. These particles are formed during the initial stage of precipitation. The particles had aluminum concentrations of 15 to 80 mass pct, with values that decreased gradually as particle size increased. These metastable dross particles were a mixture of the crystalline phase of FeZn10, which is called the "delta phase," and the high-aluminum amorphous phase, which covered the surface of the crystalline phase. The new "meta Q" concept was proposed to predict the amount of soluble aluminum in the zinc bath by considering nucleation kinetics and particle growth. The results calculated using the "meta Q" concept were compared with the values measured by the aluminum sensor, which were taken during the same period at the commercial galvanizing line. The mean of the absolute values of the differences between the calculated and measured values was 9.7 ppm.

Oceanic corrosion test of bare and zinc-protected aluminum alloys for seawater heat exchangers

NASA Technical Reports Server (NTRS)

Sasscer, D. S.; Morgan, T. O.; Rivera, C.; Ernst, R.; Scott, A. C.; Summerson, T. J.

1982-01-01

Bare 3004 tubes, 7072 Alclad 3004 tubes, and bare and zinc diffusion treated 3003 extrusions from a brazed aluminum, plate-fin heat exchanger were exposed to 1.8 m/sec flowing seawater aboard an open ocean test facility moored 3.4 km off the southeast coast of Puerto Rico. After six months exposure, the average corrosion rates for most varieties of aluminum materials converged to a low value of 0.015 mm/yr (0.6 mils/yr). Pitting did not occur in bare 3003 and 3004 samples during the six month test. Pitting did occur to varying degrees in the Alclad and zinc diffusion treated material, but did not penetrate to the base metal. Biofouling countermeasures (intermittent chlorination and brushing) did not affect the corrosion rates to any significant extent. Intermittent chlorination at a level of 0.5 ppm for 28 minutes daily controlled microbiofouling of the samples but did not prevent the development of a macrobiofouling community in areas of the plumbing with low flow.

Japanese Resource Dependence.

DTIC Science & Technology

1982-03-01

56% 78% 86% Coal 36 68 80 Crude Oil 98 99 99 Natural Gas -- 78 78 Iron Ore 92 98 98 Copper 86 93 94 Lead 55 64 79 Zinc 36 55 79 Tin 99 98 98 Aluminum...represented by energy resources (oil, gas , coal): The availabilty of adequate energy supplies is of great significance to the minerals and metals production...liquefied natural/petroleum gas , natural gas , and uranium. To meet the country’s energy needs, virtually all forms of mineral fuels were imported to

Long-term Metal Performance of Three Permeable Pavements ...

EPA Pesticide Factsheets

EPA constructed a 4,000-m2 parking lot surfaced with three permeable pavements (permeable interlocking concrete pavers, pervious concrete, and porous asphalt) on the Edison Environmental Center in Edison, NJ in 2009. Samples from each permeable pavement infiltrate were collected for six years beginning in January 2010 and analyzed for twenty-two metals. Although the infiltrate metals concentrations varied by surface, metal concentrations in more than 99% of the permeable pavement infiltrate samples met both the groundwater effluent limitations and maximum contaminant levels in national primary drinking water regulations for barium, chromium, copper, manganese, nickel and zinc. Arsenic, cadmium, lead and antimony met those standards in 60% to 98% of the samples with no measurable difference found among pavements. Aluminum and iron in pervious concrete and porous asphalt infiltrates met standards at more than 90%, however permeable interlocking concrete paver infiltrates have 50% and 93% samples exceeds standards, respectively. Concentrations of arsenic, iron, potassium, lithium, magnesium, antimony, tin, manganese, and zinc in all permeable pavement infiltrates decreased with time, whereas, aluminum, barium, calcium, chromium and strontium in porous asphalt infiltrates increased. Most metal concentrations in permeable pavement infiltrates either exhibited no significant difference between snow/no-snow seasons or showed statistically larger concentrations

RECONDITIONING FUEL ELEMENTS

DOEpatents

Brandt, H.L.

1962-02-20

A process is given for decanning fuel elements that consist of a uranium core, an intermediate section either of bronze, silicon, Al-Si, and uranium silicide layers or of lead, Al-Si, and uranium silicide layers around said core, and an aluminum can bonded to said intermediate section. The aluminum can is dissolved in a solution of sodium hydroxide (9 to 20 wt%) and sodium nitrate (35 to 12 wt %), and the layers of the intermediate section are dissolved in a boiling sodium hydroxide solution of a minimum concentration of 50 wt%. (AEC) A method of selectively reducing plutonium oxides and the rare earth oxides but not uranium oxides is described which comprises placing the oxides in a molten solvent of zinc or cadmium and then adding metallic uranium as a reducing agent. (AEC)

Trace metals in upland headwater lakes in Ireland.

PubMed

Burton, Andrew; Aherne, Julian; Hassan, Nouri

2013-10-01

Trace elements (n = 23) in Irish headwater lakes (n = 126) were investigated to determine their ambient concentrations, fractionation (total, dissolved, and non-labile), and geochemical controls. Lakes were generally located in remote upland, acid-sensitive regions along the coastal margins of the country. Total trace metal concentrations were low, within the range of natural pristine surface waters; however, some lakes (~20 %) had inorganic labile aluminum and manganese at levels potentially harmful to aquatic organisms. Redundancy analysis indicated that geochemical weathering was the dominant controlling factor for total metals, compared with acidity for dissolved metals. In addition, many metals were positively correlated with dissolved organic carbon indicating their affinity (or complexation) with humic substances (e.g., aluminum, iron, mercury, lead). However, a number of trace metals (e.g., aluminum, mercury, zinc) were correlated with anthropogenic acidic deposition (i.e., non-marine sulfate), suggesting atmospheric sources or elevated leaching owing to acidic deposition. As transboundary air pollution continues to decline, significant changes in the cycling of trace metals is anticipated.

Evaluation and control of environmental corrosion for aluminum and steel alloys

NASA Technical Reports Server (NTRS)

Franklin, D. B.

1977-01-01

Corrosion protection systems for aerospace application and the effects of surface treatments and methods of controlling stress corrosion are evaluated. Chromate pigmented systems were found to be most effective for aluminum alloys; zinc-rich coatings gave the greatest protection to steel alloys. Various steel and aluminum alloys are rated for stress corrosion resistance.

Determination of instream metal loads using tracer-injection and synoptic-sampling techniques in Wightman Fork, southwestern Colorado, September 1997

USGS Publications Warehouse

Ortiz, Roderick F.; Bencala, Kenneth E.

2001-01-01

Spatial determinations of the metal loads in Wightman Fork can be used to identify potential source areas to the stream. In September 1997, a chloride tracer-injection study was done concurrently with synoptic water-quality sampling in Wightman Fork near the Summitville Mine site. Discharge was determined and metal concentrations at 38 sites were used to generate mass-load profiles for dissolved aluminum, copper, iron, manganese, and zinc. The U.S. Environmental Protection Agency had previously identified these metals as contaminants of concern.Metal loads increased substantially in Wightman Fork near the Summitville Mine. A large increase occurred along a 60-meter reach that is north of the North Waste Dump and generally corresponds to a region of radial faults. Metal loading from this reach was equivalent to 50 percent or more of the dissolved aluminum, copper, iron, manganese, and zinc load upstream from the outfall of the Summitville Water Treatment Facility (SWTF). Overall, sources along the entire reach upstream from the SWTF were equivalent to 15 percent of the iron, 33 percent of the copper and manganese, 58 percent of the zinc, and 66 percent of the aluminum load leaving the mine site. The largest increases in metal loading to Wightman Fork occurred as a result of inflow from Cropsy Creek. Aluminum, iron, manganese, and zinc loads from Cropsy Creek were equivalent to about 40 percent of the specific metal load leaving the mine site. Copper, iron, and manganese loads from Cropsy Creek were nearly as large or larger than the load from sources upstream from the SWTF.

40 CFR 467.62 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions... off-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.680...

40 CFR 467.62 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions... off-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.680...

40 CFR 467.22 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions...-lbs) of aluminum rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079...

40 CFR 467.22 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions...-lbs) of aluminum rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079...

40 CFR 467.63 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions...-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0...

40 CFR 467.63 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions...-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0...

Change of Hot Cracking Susceptibility in Welding of High Strength Aluminum Alloy AA 7075

NASA Astrophysics Data System (ADS)

Holzer, M.; Hofmann, K.; Mann, V.; Hugger, F.; Roth, S.; Schmidt, M.

High strength aluminum alloys are known as hard to weld alloys due to their high hot crack susceptibility. However, they have high potential for applications in light weight constructions of automotive industry and therefore it is needed to increase weldability. One major issue is the high hot cracking susceptibility. Vaporization during laser beam welding leads to a change of concentration of the volatile elements magnesium and zinc. Hence, solidification range of the weld and therefore hot cracking susceptibility changes. Additionally, different welding velocities lead to changed solidification conditions with certain influence on hot cracking. This paper discusses the influence of energy per unit length during laser beam welding of AA 7075 on the change of element concentration in the weld seam and the resulting influence on hot cracking susceptibility. Therefore EDS-measurements of weld seams generated with different velocities are performed to determine the change of element concentration. These quantitative data is used to numerically calculate the solidification range in order to evaluate its influence on the hot cracking susceptibility. Besides that, relative hot crack length and mechanical properties are measured. The results increase knowledge about welding of high strength aluminum alloy AA 7075 and hence support further developing of the welding process.

40 CFR 467.23 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079 Aluminum 0.84 0.42 Subpart...

40 CFR 467.23 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory... rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079 Aluminum 0.84 0.42 Subpart...

40 CFR 467.23 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079 Aluminum 0.84 0.42 Subpart...

40 CFR 467.23 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079 Aluminum 0.84 0.42 Subpart...

40 CFR 467.63 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions or Soaps... emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0.285 Aluminum 3.00 1.49 Subpart F...

40 CFR 467.52 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Neat Oils... drawn with neat oils Chromium 0.022 0.0090 Cyanide 0.015 0.0050 Zinc 0.073 0.031 Aluminum 0.32 0.160 Oil...

21 CFR 82.2051 - Lakes (Ext. D&C).

Code of Federal Regulations, 2010 CFR

2010-04-01

..., titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or on any combination of... is a salt in which is combined the basic radical sodium, potassium, barium, or calcium; or (ii) a... color with the basic radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium. (2...

21 CFR 82.2051 - Lakes (Ext. D&C).

Code of Federal Regulations, 2012 CFR

2012-04-01

..., titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or on any combination of... is a salt in which is combined the basic radical sodium, potassium, barium, or calcium; or (ii) a... color with the basic radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium. (2...

21 CFR 82.2051 - Lakes (Ext. D&C).

Code of Federal Regulations, 2013 CFR

2013-04-01

..., titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or on any combination of... is a salt in which is combined the basic radical sodium, potassium, barium, or calcium; or (ii) a... color with the basic radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium. (2...

21 CFR 82.2051 - Lakes (Ext. D&C).

Code of Federal Regulations, 2014 CFR

2014-04-01

..., titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or on any combination of... is a salt in which is combined the basic radical sodium, potassium, barium, or calcium; or (ii) a... color with the basic radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium. (2...

21 CFR 82.2051 - Lakes (Ext. D&C).

Code of Federal Regulations, 2011 CFR

2011-04-01

..., titanium dioxide, zinc oxide, talc, rosin, aluminum benzoate, calcium carbonate, or on any combination of... is a salt in which is combined the basic radical sodium, potassium, barium, or calcium; or (ii) a... color with the basic radical sodium, potassium, aluminum, barium, calcium, strontium, or zirconium. (2...

Aluminum-dependent regulation of intracellular silicon in the aquatic invertebrate Lymnaea stagnalis

PubMed Central

Desouky, Mahmoud; Jugdaohsingh, Ravin; McCrohan, Catherine R.; White, Keith N.; Powell, Jonathan J.

2002-01-01

Silicon is essential for some plants, diatoms, and sponges but, in higher animals, its endogenous regulation has not been demonstrated. Silicate ions may be natural ligands for aluminum and here we show that, in the freshwater snail (Lymnaea stagnalis), intracellular silicon seems specifically up-regulated in response to sublethal aluminum exposure. X-ray microanalysis showed that exposure of snails to low levels of aluminum led to its accumulation in lysosomal granules, accompanied by marked up-regulation of silicon. Increased lysosomal levels of silicon were a specific response to aluminum because cadmium and zinc had no such effect. Furthermore, intra-lysosomal sulfur from metallothionein and other sulfur-containing ligands was increased after exposure to cadmium and zinc but not aluminum. To ensure that these findings indicated a specific in vivo response, and not ex vivo formation of hydroxy-aluminosilicates (HAS) from added aluminum (555 μg/liter) and water-borne silicon (43 μg/liter), two further studies were undertaken. In a ligand competition assay the lability of aluminum (527 μg/liter) was completely unaffected by the presence of silicon (46 μg/liter), suggesting the absence of HAS. In addition, exogenous silicon (6.5 mg/liter), added to the water column to promote formation of HAS, caused a decrease in lysosomal aluminum accumulation, showing that uptake of HAS would not explain the loading of aluminum into lysosomal granules. These findings, and arguments on the stability, lability, and kinetics of aluminum–silicate interactions, suggest that a silicon-specific mechanism exists for the in vivo detoxification of aluminum, which provides regulatory evidence of silicon in a multicellular organism. PMID:11891333

The Proof of the ``Vortex Theory of Matter''

NASA Astrophysics Data System (ADS)

Moon, Russell

2009-11-01

According to the Vortex Theory, protons and electrons are three-dimensional holes connected by fourth-dimensional vortices. It was further theorized that when photons are absorbed then readmitted by atoms, the photon is absorbed into the proton, moves through the fourth-dimensional vortex, then reemerges back into three-dimensional space through the electron. To prove this hypothesis, an experiment was conducted using a hollow aluminum sphere containing a powerful permanent magnet suspended directly above a zinc plate. Ultraviolet light was then shined upon the zinc. The zinc emits electrons via the photoelectric effect that are attracted to the surface of the aluminum sphere. The sphere was removed from above the zinc plate and repositioned above a sensitive infrared digital camera in another room. The ball and camera were placed within a darkened box inside a Faraday cage. Light was shined upon the zinc plate and the picture taken by the camera was observed. When the light was turned on above the zinc plate in one room, the camera recorded increased light coming from the surface of the sphere within the other room; when the light was turned off, the intensity of the infrared light coming from the surface of the sphere was suddenly diminished. Five other tests were then performed to eliminate other possible explanations such as quantum-entangled electrons.

The Proof of the ``Vortex Theory of Matter''

NASA Astrophysics Data System (ADS)

Gridnev, Konstantin; Moon, Russell; Vasiliev, Victor

2009-11-01

According to the Vortex Theory, protons and electrons are three-dimensional holes connected by fourth-dimensional vortices. It was further theorized that when photons are absorbed then readmitted by atoms, the photon is absorbed into the proton, moves through the fourth-dimensional vortex, then reemerges back into three-dimensional space through the electron^2. To prove this hypothesis, an experiment was conducted using a hollow aluminum sphere containing a powerful permanent magnet suspended directly above a zinc plate. Ultraviolet light was then shined upon the zinc. The zinc emits electrons via the photoelectric effect that are attracted to the surface of the aluminum sphere. The sphere was removed from above the zinc plate and repositioned above a sensitive infrared digital camera in another room. The ball and camera were placed within a darkened box inside a Faraday cage. Light was shined upon the zinc plate and the picture taken by the camera was observed. When the light was turned on above the zinc plate in one room, the camera recorded increased light coming from the surface of the sphere within the other room; when the light was turned off, the intensity of the infrared light coming from the surface of the sphere was suddenly diminished. Five other tests were then performed to eliminate other possible explanations such as quantum-entangled electrons.

The Proof of the ``Vortex Theory of Matter''

NASA Astrophysics Data System (ADS)

Gridnev, Konstantin; Moon, Russell; Vasiliev, Victor

2009-10-01

According to the Vortex Theory, protons and electrons are three-dimensional holes connected by fourth-dimensional vortices. It was further theorized that when photons are absorbed then readmitted by atoms, the photon is absorbed into the proton, moves through the fourth-dimensional vortex, then reemerges back into three-dimensional space through the electron^2. To prove this hypothesis, an experiment was conducted using a hollow aluminum sphere containing a powerful permanent magnet suspended directly above a zinc plate. Ultraviolet light was then shined upon the zinc. The zinc emits electrons via the photoelectric effect that are attracted to the surface of the aluminum sphere. The sphere was removed from above the zinc plate and repositioned above a sensitive infrared digital camera in another room. The ball and camera were placed within a darkened box inside a Faraday cage. Light was shined upon the zinc plate and the picture taken by the camera was observed. When the light was turned on above the zinc plate in one room, the camera recorded increased light coming from the surface of the sphere within the other room; when the light was turned off, the intensity of the infrared light coming from the surface of the sphere was suddenly diminished. Five other tests were then performed to eliminate other possible explanations such as quantum-entangled electrons.

The Proof of the ``Vortex Theory of Matter''

NASA Astrophysics Data System (ADS)

Moon, Russell; Gridnev, Konstantin; Vasiliev, Victor

2010-02-01

According to the Vortex Theory, protons and electrons are three-dimensional holes connected by fourth-dimensional vortices. It was further theorized that when photons are absorbed then readmitted by atoms, the photon is absorbed into the proton, moves through the fourth-dimensional vortex, then reemerges back into three-dimensional space through the electron. To prove this hypothesis, an experiment was conducted using a hollow aluminum sphere containing a powerful permanent magnet suspended directly above a zinc plate. Ultraviolet light was then shined upon the zinc. The zinc emits electrons via the photoelectric effect that are attracted to the surface of the aluminum sphere. The sphere was removed from above the zinc plate and repositioned above a sensitive infrared digital camera in another room. The ball and camera were placed within a darkened box inside a Faraday cage. Light was shined upon the zinc plate and the picture taken by the camera was observed. When the light was turned on above the zinc plate in one room, the camera recorded increased light coming from the surface of the sphere within the other room; when the light was turned off, the intensity of the infrared light coming from the surface of the sphere was suddenly diminished. Five other tests were then performed to eliminate other possible explanations such as quantum-entangled electrons. )

40 CFR 467.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 1.25 Aluminum 13.10 6.52 Subpart C Solution Heat Treatment Contact Cooling Water Pollutant or....24 Cyanide 0.39 0.16 Zinc 1.94 0.81 Aluminum 8.55 4.26 Subpart C Press Heat Treatment Contact Cooling...

40 CFR 467.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 1.25 Aluminum 13.10 6.52 Subpart C Solution Heat Treatment Contact Cooling Water Pollutant or....24 Cyanide 0.39 0.16 Zinc 1.94 0.81 Aluminum 8.55 4.26 Subpart C Press Heat Treatment Contact Cooling...

40 CFR 467.33 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 1.25 Aluminum 13.10 6.52 Subpart C Solution Heat Treatment Contact Cooling Water Pollutant or....24 Cyanide 0.39 0.16 Zinc 1.94 0.81 Aluminum 8.55 4.26 Subpart C Press Heat Treatment Contact Cooling...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herkovits, J.; Herkovits, F.D.; Perez-Coll

As a result of their aquatic embryonic and larval development, many species of amphibians are potentially affected by adverse environmental conditions. In this study the possibility of reducing the lethal effect of aluminum (ALC13, Mallinckrodt) in Bufo arenarum embryos by means of simultaneous zinc (ZnSO4) treatment is reported. The aluminum hazard was evaluated in a 7 day renewal toxicity testing study conducted with batches of 10 individuals (by quadruplicate) in six concentrations of aluminum plus the control at 20 C. The pH of the experimental solutions were measured. The LC100 expressed as Al(3 +) mg/L at 24 and up tillmore » 168 hours of treatment were 0.9 (the pH of the solution was 6.2 while in control Holtfreter solution the pH was 6.8). Therefore, aluminum exert a lethal effect on amphibian embryos in concentrations which reduce only slightly the pH of the maintaining solution. The lethal effect of aluminum could be reduced 100% by means of simultaneous treatment with 2 mg Zn(2 +)/L. The results point out the high sensibility of the amphibian embryos to aluminum (LC100/24hs:0.9mg Al(3 +)/L) and therefore, episodic increases in dissolved aluminum, usually concomitant with surface water pH decreases, could produce very harmful effects during embryonic stages of amphibians. The noteworthy beneficial effect of zinc against the lethal effect of aluminum could be of practical value in reducing the harmful effects exerted by aluminum. The conspicuous Al-Zn antagonism points out the need of biological test systems for recording the integrated effects of substances released to the environment.« less

High-Throughput Continuous Hydrothermal Synthesis of Transparent Conducting Aluminum and Gallium Co-doped Zinc Oxides.

PubMed

Howard, Dougal P; Marchand, Peter; McCafferty, Liam; Carmalt, Claire J; Parkin, Ivan P; Darr, Jawwad A

2017-04-10

High-throughput continuous hydrothermal flow synthesis was used to generate a library of aluminum and gallium-codoped zinc oxide nanoparticles of specific atomic ratios. Resistivities of the materials were determined by Hall Effect measurements on heat-treated pressed discs and the results collated into a conductivity-composition map. Optimal resistivities of ∼9 × 10 -3 Ω cm were reproducibly achieved for several samples, for example, codoped ZnO with 2 at% Ga and 1 at% Al. The optimum sample on balance of performance and cost was deemed to be ZnO codoped with 3 at% Al and 1 at% Ga.

ELECTRO-DEPOSITION OF NICKEL ALLOYS FROM THE PYROPHOSPHATE BATH: NICKEL- ZINC AND NICKEL-MOLYBDENUM ALLOYS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panikkar, S.K.; Char, T.L.R.

1958-02-01

Results of studies on the electrodeposition of nickel-zinc and nickel-- molybdenum alloys in a pyrophosphate bath using platinium electrodes are presented. The fects of varying current density and metal contents of the electrolyte on alloy deposit composition, cathode efficiency, and cathode potential are presented in tabular form. (J.R.D.) l2432 A study was made of the effect of homogenization on the mechanical properties of solution-treated and aged aluminum and the quantitative effects of several variables on hardness. The effect of alloying elements on the increase in hardness of aluminum is shown. (J.E.D.)

Assessment of metals exposure and sub-lethal effects in voles and small birds captured near the DeLong Mountain Regional Transportation System Road, Cape Krusenstern National Monument, Alaska, 2006

USGS Publications Warehouse

Brumbaugh, William G.; Mora, Miguel A.; May, Thomas W.

2008-01-01

Voles (n=6) and small ground-nesting birds (n=12) were live-captured near the DeLong Mountain Regional Transportation System haul road in Cape Krusenstern National Monument in northwest Alaska in 2006 to assess metals exposure and sub-lethal biological effects. Similar numbers of animals were captured from a reference site in southern Cape Krusenstern National Monument for comparison. Histopathological examination of selected organs, blood analysis, and analysis for aluminum, barium, cadmium, lead, and zinc concentrations in liver and blood samples were performed. Voles and small birds captured from near the haul road had about 20 times greater blood and liver lead concentrations and about 3 times greater cadmium concentrations when compared to those from the reference site. Barium and zinc tissue concentrations of animals collected from different sites were not remarkably different, and aluminum concentrations were below the reporting limits in most samples. There was no clear evidence of serious sub-lethal biological effects such as lesions in internal organs or DNA damage in blood in any of the animals. Accordingly, blood and liver lead concentrations in animals captured near the haul road generally were less than tissue concentration thresholds associated with serious biological effects reported from other studies; however, subtle effects resulting from lead exposure, such as the suppression of the activity of certain enzymes, cannot be ruled out for those animals nearest the haul road. Notably, liver lead concentrations of voles and small birds at the reference location were considerably less than those previously reported for similar animals at reference sites in other parts of the United States, Canada, and Europe. Results from this reconnaissance-level study indicate that voles and small birds inhabiting this area are not suffering serious biological effects as a result of metals exposure; however, continued monitoring of lead and other metals is recommended because of uncertainties noted and because biological effects thresholds might be approached if exposure levels were to increase.

Investigation of the Genotoxicity of Aluminum Oxide, β-Tricalcium Phosphate, and Zinc Oxide Nanoparticles In Vitro.

PubMed

Akbaba, Giray Buğra; Türkez, Hasan

The aim of this study was to investigate the genotoxicity of aluminum oxide (Al 2 O 3 ), β-tricalcium phosphate (β-TCP) (Ca 3 (PO 4 ) 2 ), and zinc oxide (ZnO) nanoparticles (NPs) that were 4.175, 9.058, and 19.8 nm sized, respectively, on human peripheral blood lymphocytes using micronucleus (MN) and chromosome aberration (CA) techniques. Aluminum oxide and β-TCP NPs did not show genotoxic effects on human peripheral blood cultures in vitro, even at the highest concentrations; therefore, these materials may be suitable for use as biocompatible materials. It was observed that, even at a very low dose (≥12.5 ppm), ZnO NPs had led to genotoxicity. In addition, at high concentrations (500 ppm and above), ZnO NPs caused mortality of lymphocytes. For these reasons, it was concluded that ZnO NPs are not appropriate for using as a biocompatible biomaterial.

Process for preparing zinc oxide-based sorbents

DOEpatents

Gangwal, Santosh Kumar [Cary, NC; Turk, Brian Scott [Durham, NC; Gupta, Raghubir Prasad [Durham, NC

2011-06-07

The disclosure relates to zinc oxide-based sorbents, and processes for preparing and using them. The sorbents are preferably used to remove one or more reduced sulfur species from gas streams. The sorbents comprise an active zinc component, optionally in combination with one or more promoter components and/or one or more substantially inert components. The active zinc component is a two phase material, consisting essentially of a zinc oxide (ZnO) phase and a zinc aluminate (ZnAl.sub.2O.sub.4) phase. Each of the two phases is characterized by a relatively small crystallite size of typically less than about 500 Angstroms. Preferably the sorbents are prepared by converting a precursor mixture, comprising a precipitated zinc oxide precursor and a precipitated aluminum oxide precursor, to the two-phase, active zinc oxide containing component.

Cattle mortality in the Thane district, India: a study of cause/effect relationships.

PubMed

Dogra, R K; Murthy, R C; Srivastava, A K; Gaur, J S; Shukla, L J; Varmani, B M

1996-02-01

An unexpected mortality of more than 300 cattle was investigated near a metal recovery factory located in a rural area of the Thane district of India. The factory was engaged in reclaiming lead, aluminum, tin, and zinc from discarded lead storage batteries and soft drink cans. The environmental samples (soil, leaves, grass, slag, water, and sediment), human blood and hair and animal samples (blood, urine, peritoneal fluid, liver, kidney, cow dung, ribs, and femur), collected for analysis revealed toxic levels of lead, cadmium, and chromium. Clinical examination of factory workers and school children revealed cough, fever, gastric problems, abdominal pain, skin lesions (scabies), and blue line on gums. Histopathological examination of animal tissues revealed chronic pathology with lead inclusion bodies in hepatocytes and renal tubules. Based on environmental, clinical, analytical, and histopathological observations, the mortality has been attributed to toxic levels of metals in the body and the malnourished status of the animals.

High Stability Performance of Quinary Indium Gallium Zinc Aluminum Oxide Films and Thin-Film Transistors Deposited Using Vapor Cooling Condensation Method

NASA Astrophysics Data System (ADS)

Lin, Yung-Hao; Lee, Ching-Ting

2017-08-01

High-quality indium gallium zinc aluminum oxide (IGZAO) thin films with various Al contents have been deposited using the vapor cooling condensation method. The electron mobility of the IGZAO films was improved by 89.4% on adding Al cation to IGZO film. The change in the electron concentration and mobility of the IGZAO films was 7.3% and 7.0%, respectively, when the temperature was changed from 300 K to 225 K. These experimental results confirm the high performance and stability of the IGZAO films. The performance stability mechanisms of IGZAO thin-film transistors (TFTs) were investigated in comparison with IGZO TFTs.

Zinc oxide-based sorbents and processes for preparing and using same

DOEpatents

Gangwal, Santosh Kumar; Turk, Brian Scott; Gupta, Raghubir Prasad

2005-10-04

Zinc oxide-based sorbents, and processes for preparing and using them are provided, wherein the sorbents are preferably used to remove one or more reduced sulfur species from gas streams. The sorbents contain an active zinc component, optionally in combination with one or more promoter components and/or one or more substantially inert components. The active zinc component is a two phase material, consisting essentially of a zinc oxide (ZnO) phase and a zinc aluminate (ZnAl.sub.2 O.sub.4) phase. Each of the two phases is characterized by a relatively small crystallite size of typically less than about 500 Angstroms. Preferably the sorbents are prepared by converting a precursor mixture, containing a precipitated zinc oxide precursor and a precipitated aluminum oxide precursor, to the two-phase, active zinc oxide containing component.

Zinc-oxide-based sorbents and processes for preparing and using same

DOEpatents

Gangwal, Santosh Kumar; Turk, Brian Scott; Gupta, Raghubir Prasael

2010-03-23

Zinc oxide-based sorbents, and processes for preparing and using them are provided. The sorbents are preferably used to remove one or more reduced sulfur species from gas streams. The sorbents comprise an active zinc component, optionally in combination with one or more promoter components and/or one or more substantially inert components. The active zinc component is a two phase material, consisting essentially of a zinc oxide (ZnO) phase and a zinc aluminate (ZnAl.sub.2O.sub.4) phase. Each of the two phases is characterized by a relatively small crystallite size of typically less than about 500 Angstroms. Preferably the sorbents are prepared by converting a precursor mixture, comprising a precipitated zinc oxide precursor and a precipitated aluminum oxide precursor, to the two-phase, active zinc oxide containing component.

40 CFR 467.55 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... any 1 day Maximum for monthly average mg/off-kg (lb/million off-lbs) of aluminum drawn with neat oils Chromium 0.022 0.009 Cyanide 0.015 0.006 Zinc 0.073 0.031 TTO 0.035 Oil and grease (alternate monitoring...) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Neat Oils Subcategory...

Cadmium Alternatives High Strength Steel JTP

DTIC Science & Technology

2005-03-01

Cadmium Alternatives HSS JTP Alternative Coatings Selected by JCAT: Primary Repair LHE Cadmium (control) IVD Aluminum (control) Zinc-Nickel, acid...Tin-Zinc Cadmium Alternatives HSS JTP Demonstration Tests Selected by JCAT: Phase I Phase II Hydrogen Embrittlement Hydrogen Re-Embrittlement (NRB...immersion, exposed C-ring (Army)) Bend Adhesion (Q/A) Appearance Throwing Power Composition Uniformity Strippability Galvanic Potential Bend Adhesion

Cesium recovery from aqueous solutions

DOEpatents

Goodhall, C. A.

1960-09-13

A process for recovering cesium from aqueous solutions is given in which precipitation on zinc ferricyanide is used. The precipitation is preferably carried out in solutions containing at least 0.0004M zinc ferricyanide, an acidity ranging from 0.2N mineral acid to 0.61N acid deficiency, and 1 to 2.5M aluminum nitrate. (D.L.C.)

40 CFR 466.32 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS PORCELAIN ENAMELING POINT SOURCE CATEGORY Aluminum Basis Material....19 5.06 0.16 Nickel 54.85 1.78 38.90 1.26 Zinc 51.74 1.68 21.79 1.71 Aluminum 176.98 5.74 72.35 2.35... Aluminum 36.25 1.18 14.82 0.48 Iron 9.80 0.32 5.02 0.16 [47 FR 53184, Nov. 24, 1982, as amended at 50 FR...

Use Of New Industrial Coatings for the U.S. Navy Waterfront Structures

DTIC Science & Technology

2008-01-01

as a coating for the interior and exterior of piping systems, which either are located in harsh environments or are transporting substances with...SSPC SP 10 Surfaces) (5). SyslCm Coating Sys\\~m A Zinc -rich urethane/MIOa·filled urethane/urethane 314/315/314 B Zinc -rich urethane/MIO-filled...urethanc/MIO-urethane 336/3361336 C Zinc -rich urethancl1vfiO & Alb-fined urethaneiMIO-fiIled 337/3401336 ,1 MicaceQus iron oxide. b Aluminum. urethane

Radiopacity of portland cement associated with different radiopacifying agents.

PubMed

Húngaro Duarte, Marco Antonio; de Oliveira El Kadre, Guâniara D'arc; Vivan, Rodrigo Ricci; Guerreiro Tanomaru, Juliane Maria; Tanomaru Filho, Mário; de Moraes, Ivaldo Gomes

2009-05-01

This study evaluated the radiopacity of Portland cement associated with the following radiopacifying agents: bismuth oxide, zinc oxide, lead oxide, bismuth subnitrate, bismuth carbonate, barium sulfate, iodoform, calcium tungstate, and zirconium oxide. A ratio of 20% radiopacifier and 80% white Portland cement by weight was used for analysis. Pure Portland cement and dentin served as controls. Cement/radiopacifier and dentin disc-shaped specimens were fabricated, and radiopacity testing was performed according to the ISO 6876/2001 standard for dental root sealing materials. Using Insight occlusal films, the specimens were radiographed near to a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The radiographs were digitized and radiopacity compared with the aluminum stepwedge using Digora software (Orion Corporation Soredex, Helsinki, Finland). The radiographic density data were converted into mmAl and analyzed statistically by analysis of variance and Tukey-Kramer test (alpha = 0.05). The radiopacity of pure Portland cement was significantly lower (p < 0.05) than that of dentin, whereas all cement/radiopacifier mixtures were significantly more radiopaque than dentin and Portland cement alone (p < 0.05). Portland cement/bismuth oxide and Portland cement/lead oxide presented the highest radiopacity values and differed significantly from the other materials (p < 0.05), whereas Portland cement/zinc oxide presented the lowest radiopacity values of all mixtures (p < 0.05). All tested substances presented higher radiopacity than that of dentin and may potentially be added to the Portland cement as radiopacifying agents. However, the possible interference of the radiopacifiers with the setting chemistry, biocompatibility, and physical properties of the Portland cement should be further investigated before any clinical recommendation can be done.

Metals transport in the Sacramento River, California, 1996-1997; Volume 2: Interpretation of metal loads

USGS Publications Warehouse

Alpers, Charles N.; Antweiler, Ronald C.; Taylor, Howard E.; Dileanis, Peter D.; Domagalski, Joseph L.

2000-01-01

Metals transport in the Sacramento River, northern California, from July 1996 to June 1997 was evaluated in terms of metal loads from samples of water and suspended colloids that were collected on up to six occasions at 13 sites in the Sacramento River Basin. Four of the sampling periods (July, September, and November 1996; and May-June 1997) took place during relatively low-flow conditions and two sampling periods (December 1996 and January 1997) took place during high-flow and flooding conditions, respectively. This study focused primarily on loads of cadmium, copper, lead, and zinc, with secondary emphasis on loads of aluminum, iron, and mercury.Trace metals in acid mine drainage from abandoned and inactive base-metal mines, in the East and West Shasta mining districts, enter the Sacramento River system in predominantly dissolved form into both Shasta Lake and Keswick Reservoir. The proportion of trace metals that was dissolved (as opposed to colloidal) in samples collected at Shasta and Keswick dams decreased in the order zinc ≈ cadmium > copper > lead. At four sampling sites on the Sacramento River--71, 256, 360, and 412 kilometers downstream of Keswick Dam--trace-metal loads were predominantly colloidal during both high- and low-flow conditions. The proportion of total cadmium, copper, lead, and zinc loads transported to San Francisco Bay and the Sacramento-San Joaquin Delta estuary (referred to as the Bay-Delta) that is associated with mineralized areas was estimated by dividing loads at Keswick Dam by loads 412 kilometers downstream at Freeport and the Yolo Bypass. During moderately high flows in December 1996, mineralization-related total (dissolved + colloidal) trace-metal loads to the Bay-Delta (as a percentage of total loads measured downstream) were cadmium, 87 percent; copper, 35 percent; lead, 10 percent; and zinc, 51 percent. During flood conditions in January 1997 loads were cadmium, 22 percent; copper, 11 percent; lead, 2 percent; and zinc, 15 percent. During irrigation drainage season from rice fields (May-June 1997) loads were cadmium, 53 percent; copper, 42 percent; lead, 20 percent; and zinc, 75 percent. These estimates must be qualified by the following factors: (1) metal loads at Colusa in December 1996 and at Verona in May-June 1997 generally exceeded those determined at Freeport during those sampling periods. Therefore, the above percentages represent maximum estimates of the apparent total proportion of metals from mineralized areas upstream of Keswick Dam; and (2) for logistics reasons, the Sacramento River was sampled at Tower Bridge instead of at Freeport during January 1997.Available data suggest that trace metal loads from agricultural drainage may be significant during certain flow conditions in areas where metals such as copper and zinc are added as agricultural amendments. Copper loads for sampling periods in July and September 1996 and in May-June 1997 show increases of dissolved and colloidal copper and in colloidal zinc between Colusa and Verona, the reach of the Sacramento River along which the Colusa Basin Drain, the Sacramento Slough, and other agricultural return flows are tributaries. Monthly sampling of these two agricultural drains by the USGS National Water-Quality Assessment Program shows seasonal variations in metal concentrations, reaching maximum concentrations of 4 to 6 micrograms per liter in "dissolved" (0.45-micrometer filtrate) copper concentrations in May 1996, December 1996, and June 1997. The total (dissolved plus colloidal) load of copper from the Colusa Basin Drain in June 1997 was 18 kilograms per day, whereas the copper load in Spring Creek, which drains the inactive mines on Iron Mountain, was 20 kilograms per day during the same sampling period. For comparison, during the January 1997 flood, the copper load in Spring Creek was about 1,100 kilograms per day and the copper load in the Yolo Bypass was about 7,300 kilograms per day. The data clearly indicate that most copper and zinc loads during the January 1997 flood entered the Sacramento River upstream of Colusa, and upstream of the influence of the most intense agricultural drainage return flows in the Sacramento River watershed.This study has demonstrated that some trace metals of environmental significance (cadmium, copper, and zinc) in the Sacramento River are transported largely in dissolved form at upstream sites (below Shasta Dam, below Keswick Dam, and at Bend Bridge) proximal to the mineralized areas of the West Shasta and East Shasta mining districts. In contrast, these trace metals are transported largely in colloidal form at downstream sites (Colusa, Verona, Freeport, and Yolo Bypass). Aluminum, iron, and lead were observed to be transported predominantly in the colloidal phase at all mainstem Sacramento River sampling sites during all sampling periods in this study. Despite continuous water treatment, which has removed 85 to 90 percent of the cadmium, copper, and zinc from the mine drainage at Iron Mountain, Spring Creek remains a significant source of these metals to the Sacramento River system.

Cadmium plating replacements

NASA Technical Reports Server (NTRS)

Nelson, Mary J.; Groshart, Earl C.

1995-01-01

The Boeing Company has been searching for replacements to cadmium plate. Two alloy plating systems seem close to meeting the needs of a cadmium replacement. The two alloys, zinc-nickel and tin-zinc are from alloy plating baths; both baths are neutral pH. The alloys meet the requirements for salt fog corrosion resistance, and both alloys excel as a paint base. Currently, tests are being performed on standard fasteners to compare zinc-nickel and tin-zinc on threaded hardware where cadmium is heavily used. The Hydrogen embrittlement propensity of the zinc-nickel bath has been tested, and just beginning for the tin-zinc bath. Another area of interest is the electrical properties on aluminum for tin-zinc and will be discussed. The zinc-nickel alloy plating bath is in production in Boeing Commercial Airplane Group for non-critical low strength steels. The outlook is promising that these two coatings will help The Boeing Company significantly reduce its dependence on cadmium plating.

Lead zirconate titanate-nickel zink ferrite thick-film composites: obtaining by the screen printing technique and magnetoelectric properties

NASA Astrophysics Data System (ADS)

Bush, A. A.; Shkuratov, V. Ya.; Chernykh, I. A.; Fetisov, Y. K.

2010-03-01

Layered thick-film composites containing one lead zirconate titanate (PZT) layer, one nickel zinc ferrite (NZF) layer, two PZT-NZF layers, or three PZT-NZF-PZT layers each 40-50 μm thick are prepared. The layers are applied by screen printing on a ceramic aluminum oxide substrate with a preformed contact (conducting) layer. The dielectric properties of the composites are studied in the temperature interval 80-900 K and the frequency interval 25 Hz-1 MHz. Polarized samples exhibit piezoelectric, pyroelectric, and magnetoelectric effects. In tangentially magnetized two- and three-layer composites, the magnetoelectric conversion factor equals 57 kV/(m T) at low frequencies and reaches 2000 kV/(m T) at the mechanical resonance frequency.

Effect of grit-blasting on substrate roughness and coating adhesion

NASA Astrophysics Data System (ADS)

Varacalle, Dominic J.; Guillen, Donna Post; Deason, Douglas M.; Rhodaberger, William; Sampson, Elliott

2006-09-01

Statistically designed experiments were performed to compare the surface roughness produced by grit blasting A36/1020 steel using different abrasives. Grit blast media, blast pressure, and working distance were varied using a Box-type statistical design of experiment (SDE) approach. The surface textures produced by four metal grits (HG16, HG18, HG25, and HG40) and three conventional grits (copper slag, coal slag, and chilled iron) were compared. Substrate roughness was measured using surface profilometry and correlated with operating parameters. The HG16 grit produced the highest surface roughness of all the grits tested. Aluminum and zinc-aluminum coatings were deposited on the grit-blasted substrates using the twin-wire electric are (TWEA) process. Bond strength of the coatings was measured with a portable adhesion tester in accordance with ASTM standard D 4541. The coatings on substrates roughened with steel grit exhibit superior bond strength to those prepared with conventional grit. For aluminum coatings sprayed onto surfaces prepared with the HG16 grit, the bond strength was most influenced by current, spray distance, and spray gun pressure (in that order). The highest bond strength for the zinc-aluminum coatings was attained on surfaces prepared using the metal grits.

Trace-element concentrations in streambed sediment across the conterminous United States

USGS Publications Warehouse

Rice, Karen C.

1999-01-01

Trace-element concentrations in 541 streambed-sediment samples collected from 20 study areas across the conterminous United States were examined as part of the National Water-Quality Assessment Program of the U.S. Geological Survey. Sediment samples were sieved and the <63-μm fraction was retained for determination of total concentrations of trace elements. Aluminum, iron, titanium, and organic carbon were weakly or not at all correlated with the nine trace elements examined:  arsenic, cadmium, chromium, copper, lead, mercury, nickel, selenium, and zinc. Four different methods of accounting for background/baseline concentrations were examined; however, normalization was not required because field sieving removed most of the background differences between samples. The sum of concentrations of trace elements characteristic of urban settings - copper, mercury, lead, and zinc - was well correlated with population density, nationwide. Median concentrations of seven trace elements (all nine examined except arsenic and selenium) were enriched in samples collected from urban settings relative to agricultural or forested settings. Forty-nine percent of the sites sampled in urban settings had concentrations of one or more trace elements that exceeded levels at which adverse biological effects could occur in aquatic biota.

Authenticity of Benin metalworks evaluated by inductively coupled plasma mass spectrometry and lead isotope analyses

NASA Astrophysics Data System (ADS)

Fabbri, E.; Soffritti, C.; Merlin, M.; Vaccaro, C.; Garagnani, G. L.

2017-05-01

Two metal plaques and a cock statuette belonging to a private collection and stylistically consistent with the Royal Art of Benin (Nigeria) were investigated in order to verify their authenticity. The characterization of alloys and patinas were carried out by inductively coupled plasma mass spectrometry, optical microscopy, scanning electron microscopy and energy dispersion spectroscopy, and X-Ray diffraction spectrometry. Furthermore, thermal ionization mass spectrometry was used to assess the abundances of lead isotopes and to attempt a dating by the measurement of 210Pb/204Pb ratio. The results showed that all three artefacts were mainly composed of low lead-brass alloys, with relatively high concentrations of zinc, antimony, cadmium and aluminum in the solid copper solution. Microstructures were mostly dendritic, typical of as-cast brasses, and characterized by recrystallized non-homogeneous twinned grains in areas corresponding to surface decorations, probably due to multiple hammering steps followed by partial annealing treatments. The matrix was composed of a cored α-Cu solid solution together with non-metallic inclusions, lead globules and Sn-rich precipitates in interdendritic spaces. On the surface of all metalworks, both copper and zinc oxides, a non-continuous layer of sulphur-containing contaminants and chloride-containing compounds, were identified. The lead isotope results were consistent with brasses produced shortly before or after 1900 CE. Overall, the data obtained by different techniques supported the hypothesis that the three artefacts were not authentic.

Hydrogen plasma treatment for improved conductivity in amorphous aluminum doped zinc tin oxide thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morales-Masis, M., E-mail: monica.moralesmasis@epfl.ch; Ding, L.; Dauzou, F.

2014-09-01

Improving the conductivity of earth-abundant transparent conductive oxides (TCOs) remains an important challenge that will facilitate the replacement of indium-based TCOs. Here, we show that a hydrogen (H{sub 2})-plasma post-deposition treatment improves the conductivity of amorphous aluminum-doped zinc tin oxide while retaining its low optical absorption. We found that the H{sub 2}-plasma treatment performed at a substrate temperature of 50 °C reduces the resistivity of the films by 57% and increases the absorptance by only 2%. Additionally, the low substrate temperature delays the known formation of tin particles with the plasma and it allows the application of the process to temperature-sensitivemore » substrates.« less

Catalyst for cracking kerosene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsie, C. H.

1985-06-04

A catalyst capable of cracking kerosene under lower pressure and temperature comprising kerosene; metal powder mixture of chromium powder, copper powder, lead powder, zinc powder, nickel powder, manganese powder in an amount of 12 to 13 parts by weight per 100 parts by weight of said kerosene; sulfuric acid in an amount of 15 to 30 parts by weight per 100 parts by weight of said kerosene; inorganic powder mixture of aluminum oxide powder, serpentine powder, alum powder, magnesium oxide powder, limestone powder, slake lime powder, silica powder, and granite powder in an amount of 150 to 170 parts bymore » weight per 100 parts by weight of said kerosene.« less

Assessment of metal transport into and out of Terrace Reservoir, Conejos County, Colorado, April 1994 through March 1995; interim report

USGS Publications Warehouse

Ferguson, Sheryl; Edelmann, Patrick

1996-01-01

Terrace Reservoir is the primary source of water for crops and livestock in the southwestern part of the San Luis Valley in southern Colorado. Mining activities have occurred in the basin for more than 100 years, and substantial mining of gold has occurred intermittently at the Summitville Mine.Historically, the Summitville Mine site has produced highly acidic, metal-enriched water that drained from the mine site into Wightman Fork and flowed to the Alamosa River and Terrace Reservoir. In 1994, a study was begun as part of risk-assessment and remediation efforts and to evaluate metal transport into and out of Terrace Reservoir. During the study period, the pH immediately upstream from Terrace Reservoir ranged from 4.3 to 7.8. The highest pH occurred during the pre-peak snowmelt period; the lowest pH occurred during storm runoff during summer. Downstream from Terrace Reservoir, the pH ranged from 4.6 to 7.6. The highest pH occurred during the pre-peak snowmelt period, and the lowest pH occurred during summer in mid-July. A comparison of the streamflow hydrographs upstream and downstream from Terrace Reservoir indicated that there was only a small difference between the annual volume of water that entered the reservoir and the annual volume of water that was released from the reservoir. Large spatial and temporal variations in concentrations of the metals of concern occurred during the study.The median and maximum concentrations of dissolved and total aluminum, iron, copper, cadmium, manganese, and zinc were larger upstream from the reservoir than downstream from the reservoir. The largest concentrations of dissolved aluminum, iron, copper, cadmium, manganese, and zinc generally occurred between mid-June and November. Throughout the study, aluminum was transported into the reservoir predominantly in the particulate or suspended form. Downstream from the reservoir, the suspended-aluminum fraction was predominant only during the pre-peak snowmelt and peak snowmelt periods. The temporal variations in the percentage of dissolved and suspended fraction of iron and copper downstream from Terrace Reservoir were similar to the temporal variations that occurred upstream from the reservoir. During the study period, cadmium, manganese, and zinc generally were transported into and out of the reservoir predominantly in the dissolved form. Metal loads varied considerably as a result of changes in streamflow or changes in metal concentrations, or both. The largest daily loads of aluminum, iron, and manganese were transported into and out of Terrace Reservoir during the peak snowmelt period.The reservoir was a sink for an estimated 294 tons of aluminum and 596 tons of iron. However, about 68.5 tons of total aluminum and about 194 tons of total iron were transported out of the reservoir during the study period. During the study period, about 22\\x11tons of total copper remained in the reservoir, and 39 tons was transported downstream from the reservoir. About 47 tons of total manganese and 18 tons of total-zinc loads were transported out of the reservoir; the reservoir was a sink for only a small fraction of total-manganese and -zinc.

40 CFR 143.4 - Monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Criteria for analyzing aluminum, copper, iron, manganese, silver and zinc samples with digestion or directly without digestion, and other analytical test procedures are contained in Technical Notes on...

40 CFR 143.4 - Monitoring.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Criteria for analyzing aluminum, copper, iron, manganese, silver and zinc samples with digestion or directly without digestion, and other analytical test procedures are contained in Technical Notes on...

40 CFR 143.4 - Monitoring.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Criteria for analyzing aluminum, copper, iron, manganese, silver and zinc samples with digestion or directly without digestion, and other analytical test procedures are contained in Technical Notes on...

40 CFR 143.4 - Monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Criteria for analyzing aluminum, copper, iron, manganese, silver and zinc samples with digestion or directly without digestion, and other analytical test procedures are contained in Technical Notes on...

Effects of washing on mineral composition of leaf samples of Lycium andersonii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallace, A.; Romney, E.M.; Hunter, R.B.

1982-07-01

Leaves of Lycium andersonii A. Gray from 20 different shrubs from the northern Mojave Desert were collected. Half of each sample was washed in 1/10 N HCl followed with deionized water before analysis in triplicate by optical emission spectrometry, and the other half was analyzed unwashed. Washed samples contained 12, 35, 33, 40, 55, 47, 57, 8, 8, 9, and 20 percent, respectivey, less calcium, zinc, copper, iron, aluminum, silicon, titanium, strontium, barium, lithium, and lead than did unwashed leaves. The losses probably exceed contamination for some elements, because the results differed in some respects from those obtained for citrus.more » Statisticaly significant differences were not obtained for other elements analyzed. Even though 40 to 57 percent of the iron, aluminum, silicon, and titanium was washed from the leaves, cluster analyses grouped the four elements into a common cluster whether or not the leaves had been washed. Washing resulted in a lower coefficient of variation for some of the elements compared with unwashed leaves.« less

Health and Risk Assessment by ICP-OES of Heavy Metals and Trace Minerals in Commercial Mushrooms Marketed in China.

PubMed

Huang, Mengyi; Zeng, Huansong; Xu, Baojun

2017-01-01

The objectives of this study were to investigate mineral profiles of 35 species of edible mushrooms collected in China; we compared nutritional values and tolerable values with the official recommended daily intakes (RDIs), maximum intake limits, and provisional tolerable weekly intakes. A total of 19 minerals were detected in edible mushrooms by inductively coupled plasma optical emission spectrometry. The results showed that the mushroom samples had a low percentage of RDI for the minerals calcium, iron, magnesium, manganese, zinc, potassium, and sodium and a relatively higher percentage of RDI for copper and molybdenum. The samples also had a very high percentage of RDI for chromium and selenium. The level of heavy metals in a majority of the mushrooms was above the limited level, and only concentrations of copper and zinc were safe in all mushrooms. In conclusion, the mushrooms collected in China are a good source of minerals such as molybdenum and selenium but are badly contaminated with aluminum, arsenic, cadmium, chromium, and lead.

Isomerization of Cyclooctadiene to Cyclooctyne with a Zinc/Zirconium Heterobimetallic Complex.

PubMed

Butler, Michael J; White, Andrew J P; Crimmin, Mark R

2016-06-06

Reaction of a zinc/zirconium heterobimetallic complex with 1,5-cyclooctadiene (1,5-COD) results in slow isomerization to 1,3-cyclooctadiene (1,3-COD), along with the formation of a new complex that includes a cyclooctyne ligand bridging two metal centers. While analogous magnesium/zirconium and aluminum/zirconium heterobimetallic complexes are competent for the catalytic isomerization of 1,5-COD to 1,3-COD, only in the case of the zinc species is the cyclooctyne adduct observed. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Isomerization of Cyclooctadiene to Cyclooctyne with a Zinc/Zirconium Heterobimetallic Complex

PubMed Central

Butler, Michael J.; White, Andrew J. P.

2016-01-01

Abstract Reaction of a zinc/zirconium heterobimetallic complex with 1,5‐cyclooctadiene (1,5‐COD) results in slow isomerization to 1,3‐cyclooctadiene (1,3‐COD), along with the formation of a new complex that includes a cyclooctyne ligand bridging two metal centers. While analogous magnesium/zirconium and aluminum/zirconium heterobimetallic complexes are competent for the catalytic isomerization of 1,5‐COD to 1,3‐COD, only in the case of the zinc species is the cyclooctyne adduct observed. PMID:27071992

Zinc-oxide-based nanostructured materials for heterostructure solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bobkov, A. A.; Maximov, A. I.; Moshnikov, V. A., E-mail: vamoshnikov@mail.ru

Results obtained in the deposition of nanostructured zinc-oxide layers by hydrothermal synthesis as the basic method are presented. The possibility of controlling the structure and morphology of the layers is demonstrated. The important role of the procedure employed to form the nucleating layer is noted. The faceted hexagonal nanoprisms obtained are promising for the fabrication of solar cells based on oxide heterostructures, and aluminum-doped zinc-oxide layers with petal morphology, for the deposition of an antireflection layer. The results are compatible and promising for application in flexible electronics.

Compositions of doped, co-doped and tri-doped semiconductor materials

DOEpatents

Lynn, Kelvin [Pullman, WA; Jones, Kelly [Colfax, WA; Ciampi, Guido [Watertown, MA

2011-12-06

Semiconductor materials suitable for being used in radiation detectors are disclosed. A particular example of the semiconductor materials includes tellurium, cadmium, and zinc. Tellurium is in molar excess of cadmium and zinc. The example also includes aluminum having a concentration of about 10 to about 20,000 atomic parts per billion and erbium having a concentration of at least 10,000 atomic parts per billion.

Corrosion Behavior of Sacrificial Coatings on Grade 10.9 Fasteners for Multimetal Armor Applications

DTIC Science & Technology

2013-08-01

hexavalent chromium , immersion, magniplate, trivalent chromium (TCP), bolts nonchromate, hexavalent chrome, grade 10.9 fasteners, bolt-on armor...for Testing and Materials (ASTM) B633 (4) electroplated zinc with hexavalent chromium conversion coating 2. Trivalent Chromium Process (TCP): ASTM...B633 (4) electroplated zinc with trivalent chromium conversion coating 3. AlumiPlate: Process details, entire surface electroplated with aluminum (Al

Improvements to the strength and corrosion resistance of aluminum-magnesium-manganese alloys of near-AA5083 chemistry

NASA Astrophysics Data System (ADS)

Carroll, Mark Christopher

Aluminum alloys of the 5000 series (AI-Mg-Mn) are extremely popular in a wide range of applications that call for a balance of moderately high strength, good corrosion resistance, and light weight, all at a moderate cost. One of the most popular 5000 series alloys is designated A1-5083, containing, in addition to aluminum, approximately 4 wt% magnesium and 0.7 wt% manganese. In order to increase the range of versatility of this particular alloy, a number of modifications have been examined that will potentially improve the strength and corrosion resistance characteristics while maintaining a chemical composition that is very close to the proven 5083 alloy. The strength of the 5083-based alloys under study are investigated with two goals in mind---to maximize the potential strength characteristics in a "standard" 5083 form through changes in minor processing parameters or through minor alloying additions. Increasing the standard alloy's potential is possible through improved efficiency of "preprocessing" heat treatments that maximize the homogeneous dispersion of secondary manganese-based particles. For the modified alloy study, additions of scandium and zirconium are shown to improve strength not only by forming secondary particles in the alloy, but also through substitutional solid solution strengthening, even when added at very small levels. Corrosion resistance of these 5083-based alloys is investigated once again through minor alloying additions; specifically zinc, copper, and silver. Zinc is particularly effective in that it changes the corrosion-susceptible binary aluminum-magnesium phase that would otherwise form on grain boundaries following exposure to moderately elevated temperatures for extended periods of time to a ternary aluminum-magnesium-zinc phase. This chemical composition of this ternary phase that forms following zinc additions can be further altered through minor additions of copper and silver. By determining threshold levels for these modifications while maintaining a chemical composition that is very near that of standard Al-5083, it can be shown that even minor modifications to processing and alloying parameters can have a favorable effect on the final bulk properties of the alloy. The increased range of strength and corrosion resistance of these lightly modified alloys make them more attractive in a broadened range of potential applications.

REMOVAL OF RADIOACTIVE IONS FROM WATERS

DOEpatents

Silker, W.B.

1962-04-10

A process for removing neutron-reaction products, such as phosphorus, arsenic, manganese, copper, zinc, lanthanides, and actinides, from aqueous solutions by sorption on particles of aluminum metal is described. (AEC)

Blood-collection device for trace and ultra-trace metal specimens evaluated.

PubMed

Moyer, T P; Mussmann, G V; Nixon, D E

1991-05-01

We evaluated the evacuated phlebotomy tube designed specifically for trace metal analysis by Sherwood Medical Co. Pools of human serum containing known concentrations of aluminum, arsenic, calcium, cadmium, copper, chromium, iron, lead, magnesium, manganese, mercury, selenium, and zinc were exposed to the tube and rubber stopper for defined periods ranging from 5 min to 24 h. Analysis for each element was performed in a randomized fashion under rigidly controlled conditions by use of standard electrothermal atomization atomic absorption spectroscopy, inductively coupled plasma atomic emission spectroscopy, and cold vapor atomic absorption spectrometry. In addition, for comparative purposes, we collected blood samples from normal volunteers by use of ultra-clean polystyrene phlebotomy syringes as well as standard evacuated phlebotomy tubes. We conclude that, except for lead, there was no significant contribution of any trace element studied from the evaluated tube and stopper to the serum. Because whole blood is the usual specimen for lead testing, the observation of a trace amount of lead in this tube designed for serum collection is trivial.

Relative SHG measurements of metal thin films: Gold, silver, aluminum, cobalt, chromium, germanium, nickel, antimony, titanium, titanium nitride, tungsten, zinc, silicon and indium tin oxide

NASA Astrophysics Data System (ADS)

Che, Franklin; Grabtchak, Serge; Whelan, William M.; Ponomarenko, Sergey A.; Cada, Michael

We have experimentally measured the surface second-harmonic generation (SHG) of sputtered gold, silver, aluminum, zinc, tungsten, copper, titanium, cobalt, nickel, chromium, germanium, antimony, titanium nitride, silicon and indium tin oxide thin films. The second-harmonic response was measured in reflection using a 150 fs p-polarized laser pulse at 1561 nm. We present a clear comparison of the SHG intensity of these films relative to each other. Our measured relative intensities compare favorably with the relative intensities of metals with published data. We also report for the first time to our knowledge the surface SHG intensity of tungsten and antimony relative to that of well known metallic thin films such as gold and silver.

Resource Demand Scenarios for the Major Metals.

PubMed

Elshkaki, Ayman; Graedel, T E; Ciacci, Luca; Reck, Barbara K

2018-03-06

The growth in metal use in the past few decades raises concern that supplies may be insufficient to meet demands in the future. From the perspective of historical and current use data for seven major metals-iron, manganese, aluminum, copper, nickel, zinc, and lead-we have generated several scenarios of potential metal demand from 2010 to 2050 under alternative patterns of global development. We have also compared those demands with various assessments of potential supply to midcentury. Five conclusions emerge: (1) The calculated demand for each of the seven metals doubles or triples relative to 2010 levels by midcentury; (2) The largest demand increases relate to a scenario in which increasingly equitable values and institutions prevail throughout the world; (3) The metal recycling flows in the scenarios meet only a modest fraction of future metals demand for the next few decades; (4) In the case of copper, zinc, and perhaps lead, supply may be unlikely to meet demand by about midcentury under the current use patterns of the respective metals; (5) Increased rates of demand for metals imply substantial new energy provisioning, leading to increases in overall global energy demand of 21-37%. These results imply that extensive technological transformations and governmental initiatives could be needed over the next several decades in order that regional and global development and associated metal demand are not to be constrained by limited metal supply.

Ballistic parameters of .177 (4.5 mm) caliber plastic-sleeved composite projectiles compared to conventional lead pellets.

PubMed

Frank, Matthias; Schönekeß, Holger; Jäger, Frank; Herbst, Jörg; Ekkernkamp, Axel; Nguyen, Thanh Tien; Bockholdt, Britta

2013-11-01

The capability of conventional air gun lead pellets (diabolo pellets) to cause severe injuries or fatalities even at low kinetic energy levels is well documented in medical literature. Modern composite hunting pellets, usually a metal core (made of steel, lead, zinc, or a zinc and aluminum alloy) encased in a plastic sleeve, are of special forensic and traumatological interest. These projectiles are advertised by the manufacturers to discharge at higher velocities than conventional air gun pellets, thus generating very high tissue-penetrating capabilities. Lack of experimental data on these uncommon air gun projectiles induced this work. Ballistic parameters of 12 different caliber .177 (4.5 mm) composite pellets, discharged from two spring-piston air guns (Weihrauch HW 35, Webley CUB) and three pneumatic air guns (Walther LGR, Walther LG400, Walther LP300), were investigated using a ballistic speed measurement system and compared to a conventional diabolo pellet (RWS Meisterkugel) as reference projectile. Although overall results were inconsistent, for some projectile-weapon combinations (particularly spring-piston air guns), a significant change of the kinetic energy (-53 up to +48 %) to the reference projectile was observed. The data provided in this work may serve as a basis for forensic investigation as well as traumatological diagnosis and treatment of injuries caused by these uncommon projectiles.

Assessment of methane production from shredder waste in landfills: The influence of temperature, moisture and metals.

PubMed

Fathi Aghdam, Ehsan; Scheutz, Charlotte; Kjeldsen, Peter

2017-05-01

In this study, methane (CH 4 ) production rates from shredder waste (SW) were determined by incubation of waste samples over a period of 230days under different operating conditions, and first-order decay kinetic constants (k-values) were calculated. SW and sterilized SW were incubated under different temperatures (20-25°C, 37°C, and 55°C), moisture contents (35% and 75% w/w) and amounts of inoculum (5% and 30% of the samples wet weight). The biochemical methane potential (BMP) from different types of SW (fresh, old and sieved) was determined and compared. The ability of metals (iron, aluminum, zinc, and copper) contained in SW to provide electrons for methanogens resulting in gas compositions with high CH 4 contents and very low CO 2 contents was investigated. The BMP of SW was 1.5-6.2kg CH 4 /ton waste. The highest BMP was observed in fresh SW samples, while the lowest was observed in sieved samples (fine fraction of SW). Abiotic production of CH 4 was not observed in laboratory incubations. The biotic experiments showed that when the moisture content was 35% w/w and the temperature was 20-25°C, CH 4 production was extremely low. Increasing the temperature from 20-25°C to 37°C resulted in significantly higher CH 4 production while increasing the temperature from 37°C to 55°C resulted in higher CH 4 production, but to a lower extent. Increasing the moisture and inoculum content also increased CH 4 production. The k-values were 0.033-0.075yr -1 at room temperature, 0.220-0.429yr -1 at 37°C and 0.235-0.488yr -1 at 55°C, indicating that higher temperatures resulted in higher k-values. It was observed that H 2 can be produced by biocorrosion of iron, aluminum, and zinc and it was shown that produced H 2 can be utilized by hydrogenotrophic methanogens to convert CO 2 to CH 4 . Addition of iron and copper to SW resulted in inhibition of CH 4 production, while addition of aluminum and zinc resulted in higher CH 4 production. This suggested that aluminum and zinc contribute to high CH 4 production from SW by providing H 2 for hydrogenotrophic methanogens. Gas compositions with higher CH 4 and lower CO 2 observed in landfilled SW are thus most likely due to the consumption of existing CO 2 in the produced biogas and the produced H 2 by biocorrosion of aluminum and zinc by methanogens. Copyright © 2016 Elsevier Ltd. All rights reserved.

I-III-VI.sub.2 based solar cell utilizing the structure CuInGaSe.sub.2 CdZnS/ZnO

DOEpatents

Chen, Wen S.; Stewart, John M.

1992-01-07

A thin film I-III-VI.sub.2 based solar cell having a first layer of copper indium gallium selenide, a second layer of cadmium zinc sulfide, a double layer of zinc oxide, and a metallization structure comprised of a layer of nickel covered by a layer of aluminum. An optional antireflective coating may be placed on said metallization structure. The cadmium zinc sulfide layer is deposited by means of an aqueous solution growth deposition process and may actually consist of two layers: a low zinc content layer and a high zinc content layer. Photovoltaic efficiencies of 12.5% at Air Mass 1.5 illumination conditions and 10.4% under AMO illumination can be achieved.

Method for making an aluminum or copper substrate panel for selective absorption of solar energy

NASA Technical Reports Server (NTRS)

Roberts, M. L.; Sharpe, M. H.; Krupnick, A. C. (Inventor)

1978-01-01

A panel is described for selectively absorbing solar energy comprising an aluminum substrate. A zinc layer was covered by a layer of nickel and an outer layer of solar energy absorbing nickel oxide or a copper substrate with a nickel layer. A layer of solar energy absorbing nickel oxide distal from the copper substrate was included. A method for making these panels is disclosed.

JACKETED FUEL ELEMENT

DOEpatents

Wigner, E.P.; Szilard, L.; Creutz, E.C.

1959-02-01

These fuel elements are comprised of a homogeneous metallic uranium body completely enclosed and sealed in an aluminum cover. The uranium body and aluminum cover are bonded together by a layer of zinc located between them. The bonding layer serves to improve transfer of heat, provides an additional protection against corrosion of the uranium by the coolant, and also localizes any possible corrosion by preventing travel of corrosive material along the surface of the fuel element.

Wastewater Characterization Survey, Edwards Air Force Base, California

DTIC Science & Technology

1992-08-01

sampling, 23 and 24 Feb 92, concentrations of aluminum, chromium , copper, and iron were found to be slightly elevated when compared to average...concentrations of these metals detected during the other 6 sampling days. Detectable concentrations of aluminum, chromium , and zinc could be the result of...35.00 Cyanide .......................... 30.00 23.00 49.00 Chemical Oxygen Demand ........ 25.00 13.00 40.00 Chromium VI ...................... 25.00

Trace elements in sera from patients with renal disease

NASA Astrophysics Data System (ADS)

Miura, Yoshinori; Nakai, Keiko; Sera, Kouichiro; Sato, Michirou

1999-04-01

In hemodialysis (HD) patients, an accumulation of trace elements such as aluminum, copper, silicon and vanadium has been reported. Aluminum-caused encephalopathy and aluminum-related bone diseases are important trace element-related complications. Using particle induced X-ray emission (PIXE) we determined concentrations of aluminum, silicon, copper, zinc, selenium and bromine in sera of 29 patients with HD, 14 nondialysis patients with renal disease (RD) and 27 normal controls. The concentration of serum silicon of the patients with HD was 107.4 ± 61.3 μmol/l, which is markedly higher than that of normal controls (48.3 ± 25.8 μmol/l, p < 0.0001). The serum concentrations of zinc and bromine in patients with HD were 11.9 ± 1.7 and 21.3 ± 3.0 μmol/l, respectively. Both were markedly lower than those of normal controls (15.6 ± 2.6, 69.2 ± 8.3 μmol/l, p < 0.0001). The concentrations of aluminium and bromine in the serum of patients with RD were 171.9 ± 64.3 and 81.9 ± 11.6 μmol/l, which were markedly higher than those of normal controls ( p < 0.0001, p < 0.001). No significant differences were observed in the concentration of copper and selenium among three groups.

Aluminium or copper substrate panel for selective absorption of solar energy

NASA Technical Reports Server (NTRS)

Roberts, M. L.; Sharpe, M. H.; Krupnick, A. C. (Inventor)

1979-01-01

A method for making panels which selectively absorb solar energy is disclosed. The panels are comprised of an aluminum substrate, a layer of zinc thereon, a layer of nickel over the zinc layer and an outer layer of solar energy absorbing nickel oxide or a copper substrate with a layer of nickel thereon and a layer of solar energy absorbing nickel oxide distal from the copper substrate.

Efficient indium-tin-oxide free inverted organic solar cells based on aluminum-doped zinc oxide cathode and low-temperature aqueous solution processed zinc oxide electron extraction layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dazheng; Zhang, Chunfu, E-mail: cfzhang@xidian.edu.cn; Wang, Zhizhe

Indium-tin-oxide (ITO) free inverted organic solar cells (IOSCs) based on aluminum-doped zinc oxide (AZO) cathode, low-temperature aqueous solution processed zinc oxide (ZnO) electron extraction layer, and poly(3-hexylthiophene-2, 5-diyl):[6, 6]-phenyl C{sub 61} butyric acid methyl ester blend were realized in this work. The resulted IOSC with ZnO annealed at 150 °C shows the superior power conversion efficiency (PCE) of 3.01%, if decreasing the ZnO annealing temperature to 100 °C, the obtained IOSC also shows a PCE of 2.76%, and no light soaking issue is observed. It is found that this ZnO film not only acts as an effective buffer layer but also slightlymore » improves the optical transmittance of AZO substrates. Further, despite the relatively inferior air-stability, these un-encapsulated AZO/ZnO IOSCs show comparable PCEs to the referenced ITO/ZnO IOSCs, which demonstrates that the AZO cathode is a potential alternative to ITO in IOSCs. Meanwhile, this simple ZnO process is compatible with large area deposition and plastic substrates, and is promising to be widely used in IOSCs and other relative fields.« less

A zinc finger transcription factor ART1 regulates multiple genes implicated in aluminum tolerance in rice.

PubMed

Yamaji, Naoki; Huang, Chao Feng; Nagao, Sakiko; Yano, Masahiro; Sato, Yutaka; Nagamura, Yoshiaki; Ma, Jian Feng

2009-10-01

Aluminum (Al) toxicity is the major limiting factor of crop production on acid soils, but some plant species have evolved ways of detoxifying Al. Here, we report a C2H2-type zinc finger transcription factor ART1 (for Al resistance transcription factor 1), which specifically regulates the expression of genes related to Al tolerance in rice (Oryza sativa). ART1 is constitutively expressed in the root, and the expression level is not affected by Al treatment. ART1 is localized in the nucleus of all root cells. A yeast one-hybrid assay showed that ART1 has a transcriptional activation potential and interacts with the promoter region of STAR1, an important factor in rice Al tolerance. Microarray analysis revealed 31 downstream transcripts regulated by ART1, including STAR1 and 2 and a couple of homologs of Al tolerance genes in other plants. Some of these genes were implicated in both internal and external detoxification of Al at different cellular levels. Our findings shed light on comprehensively understanding how plants detoxify aluminum to survive in an acidic environment.

Reconnaissance for determining effects of land use and surficial geology on concentrations of selected elements on streambed materials from the coal-mining region, southwestern Indiana, October 1979 to March 1980

USGS Publications Warehouse

Wilber, W.G.; Boje, Rita R.

1982-01-01

Streambed materials were collected in October 1979 from 69 watersheds in Southwest Indiana having predominantly forested, agricultural, reclaimed, and unreclaimed mined land use to determine whether concentrations of sorbed and acid-soluble metals and trace elements were affected by land use and surficial geology. Analysis of variance indicated that 10% or more of the total variation in aluminum, arsenic, cobalt, iron, nickel, selenium, and zinc concentrations on streambed materials was accounted for by differences in land use. Concentrations of aluminum, cobalt, iron, nickel, selenium, and zinc on streambed materials smaller than 0.062-millimeter from mined watersheds were significantly greater than the concentrations of these elements on streambed materials from agricultural and forested watersheds. The greater concentrations of these elements on streambed materials are due to (1) their concentrations in mine drainage and their subsequent absorption and (or) copecipitation with the oxides and hydroxides of aluminum and iron and (2) their concentrations in coal and pyritic material in streambed materials. (USGS)

Cathodic Protection Deployment on Space Shuttle Solid Rocket Boosters

NASA Technical Reports Server (NTRS)

Zook, Lee M.

1998-01-01

Corrosion protection of the space shuttle solid rocket boosters incorporates the use of cathodic protection(anodes) in concert with several coatings systems. The SRB design has large carbon/carbon composites(motor nozzle) electrically connected to an aluminum alloy structure. Early in the STS program, the aluminum structures incurred tremendous corrosive attack due primarily to the galvanic couple to the carbon/carbon nozzle at coating damage locations. Also contributing to the galvanic corrosion problem were stainless steel and titanium alloy components housed within the aluminum structures and electrically connected to the aluminum structures. This paper will highlight the evolution in the protection of the aluminum structures, providing historical information and summary data from the operation of the corrosion protection systems. Also, data and information will be included regarding the evaluation and deployment of inorganic zinc rich primers as anode area on the aluminum structures.

Metal | polypyrrole battery with the air regenerated positive electrode

NASA Astrophysics Data System (ADS)

Grgur, Branimir N.

2014-12-01

Recharge characteristics of the battery based on the electrochemically synthesized polypyrrole cathode and aluminum, zinc, or magnesium anode in 2 M NH4Cl are investigated. It is shown that polypyrrole electrode can be regenerated by the reoxidation with the dissolved oxygen from the air. Using the polypyrrole synthesized on high surface graphite-felt electrode under modest discharge conditions, stable discharge voltage of 1.1 V is obtained. Such behavior is explained by the complex interaction of polypyrrole and hydrogen peroxide produced by the oxygen reduction reaction. The electrochemical characteristics are compared with the zinc-manganese dioxide and zinc-air systems.

Powder metallurgy: Solid and liquid phase sintering of copper

NASA Technical Reports Server (NTRS)

Sheldon, Rex; Weiser, Martin W.

1993-01-01

Basic powder metallurgy (P/M) principles and techniques are presented in this laboratory experiment. A copper based system is used since it is relatively easy to work with and is commercially important. In addition to standard solid state sintering, small quantities of low melting metals such as tin, zinc, lead, and aluminum can be added to demonstrate liquid phase sintering and alloy formation. The Taguchi Method of experimental design was used to study the effect of particle size, pressing force, sintering temperature, and sintering time. These parameters can be easily changed to incorporate liquid phase sintering effects and some guidelines for such substitutions are presented. The experiment is typically carried out over a period of three weeks.

Scientific Background for Processing of Aluminum Waste

NASA Astrophysics Data System (ADS)

Kononchuk, Olga; Alekseev, Alexey; Zubkova, Olga; Udovitsky, Vladimir

2017-11-01

Changing the source of raw materials for producing aluminum and the emergence of a huge number of secondary alumina waste (foundry slag, sludge, spent catalysts, mineral parts of coal and others that are formed in various industrial enterprises) require the creation of scientific and theoretical foundations for their processing. In this paper, the aluminum alloys (GOST 4784-97) are used as an aluminum raw material component, containing the aluminum component produced as chips in the machine-building enterprises. The aluminum waste is a whole range of metallic aluminum alloys including elements: magnesium, copper, silica, zinc and iron. Analysis of the aluminum waste A1- Zn-Cu-Si-Fe shows that depending on the content of the metal the dissolution process of an aluminum alloy should be treated as the result of the chemical interaction of the metal with an alkaline solution. It is necessary to consider the behavior of the main components of alloys in an alkaline solution as applied to the system Na2O - Al2O3 - SiO2 - CO2 - H2O.

Migration of 18 trace elements from ceramic food contact material: influence of pigment, pH, nature of acid and temperature.

PubMed

Demont, M; Boutakhrit, K; Fekete, V; Bolle, F; Van Loco, J

2012-03-01

The effect of pH, nature of acid and temperature on trace element migration from ceramic ware treated with 18 commercially available glazes was studied. Besides of the well-studied lead and cadmium, migration of other toxic and non toxic elements such as aluminum, boron, barium, cobalt, chrome, copper, iron, lithium, magnesium, manganese, nickel, antimony, tin, strontium, titanium, vanadium, zinc and zirconium was investigated in order to evaluate their potential health hazards. Trace element concentrations were determined with Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). This study suggests that there is indeed a health risk concerning the possible migration of other elements than lead and cadmium. At low pH (2

Modification of optical and electrical properties of zinc oxide-coated porous silicon nanostructures induced by swift heavy ion

PubMed Central

2012-01-01

Morphological and optical characteristics of radio frequency-sputtered zinc aluminum oxide over porous silicon (PS) substrates were studied before and after irradiating composite films with 130 MeV of nickel ions at different fluences varying from 1 × 1012 to 3 × 1013 ions/cm2. The effect of irradiation on the composite structure was investigated by scanning electron microscopy, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence spectroscopy. Current–voltage characteristics of ZnO-PS heterojunctions were also measured. As compared to the granular crystallites of zinc oxide layer, Al-doped zinc oxide (ZnO) layer showed a flaky structure. The PL spectrum of the pristine composite structure consists of the emission from the ZnO layer as well as the near-infrared emission from the PS substrate. Due to an increase in the number of deep-level defects, possibly oxygen vacancies after swift ion irradiation, PS-Al-doped ZnO nanocomposites formed with high-porosity PS are shown to demonstrate a broadening in the PL emission band, leading to the white light emission. The broadening effect is found to increase with an increase in the ion fluence and porosity. XRD study revealed the relative resistance of the film against the irradiation, i.e., the irradiation of the structure failed to completely amorphize the structure, suggesting its possible application in optoelectronics and sensing applications under harsh radiation conditions. PMID:22748164

Effect of Chromate and Chromate-Free Organic Coatings on Corrosion Fatigue of an Aluminum Alloy

DTIC Science & Technology

2012-02-20

Investigations of alloy AA7075 corrosion in acid rain solution, inhibited by chromate-free blends of zinc phosphate with bentonite, zeolite and calcium...with solution components. Single use of zinc phosphate and these ion exchanged pigments for corrosion inhibition do not provide desired effect...primer performance against corrosion fatigue cracking under a commercial polyurethane topcoat. As a control , they used samples of chromated AA2024

Synthesis of (Hexaconazole-Zinc/Aluminum-Layered Double Hydroxide Nanocomposite) Fungicide Nanodelivery System for Controlling Ganoderma Disease in Oil Palm.

PubMed

Mustafa, Isshadiba F; Hussein, Mohd Zobir; Saifullah, Bullo; Idris, Abu Seman; Hilmi, Nur Hailini Z; Fakurazi, Sharida

2018-01-31

A fungicide, hexaconazole was successfully intercalated into the intergalleries of zinc/aluminum-layered double hydroxide (ZALDH) using the ion-exchange method. Due to the intercalation of hexaconazole, the basal spacing of the ZALDH was increased from 8.7 Å in ZALDH to 29.4 Å in hexaconazole-intercalated ZALDH (HZALDH). The intercalation of hexaconazole into the interlayer of the nanocomposite was confirmed using the Fourier-transform infrared (FTIR) study. This supramolecular chemistry intercalation process enhanced the thermal stability of the hexaconazole moiety. The fungicide loading was estimated to be 51.8%. The nanodelivery system also shows better inhibition toward the Ganoderma boninense growth than the counterpart, free hexaconazole. The results from this work have a great potential to be further explored for combating basal stem rot (BSR) disease in oil palm plantation.

Titanium, aluminum and zinc complexes containing diamine-bis(benzotriazole phenolate) ligands: Synthesis, structural characterization and catalytic studies for ring-opening polymerization of ε-caprolactone

NASA Astrophysics Data System (ADS)

Liu, Zheng-Tang; Li, Chen-Yu; Chen, Jhy-Der; Liu, Wan-Ling; Tsai, Chen-Yen; Ko, Bao-Tsan

2017-04-01

Structurally diverse metal complexes bearing diamine-bis(benzotriazole phenolate) (DiBTP) ligands have been synthesized and fully characterized by single crystal X-ray crystallography. The reaction of Ti(OiPr)4 with C8MEADiBTP-H2 or C8BEADiBTP-H2 (1.0 mol equiv.) generated the monomeric titanium alkoxy complexes [(C8MEADiBTP)Ti(OiPr)2] (1) and [(C8BEADiBTP)Ti(OiPr)2] (2), respectively. Moreover, C8BEADiBTP-H2 reacted with 2.0 molar equiv. of AlMe3 to give the tetra-coordinated di-aluminum complex [(C8BEADiBTP)Al2Me4] (3). Zinc complex [(C8BEADiBTP)Zn2Et2] (4) could be obtained by the alkane elimination of ZnEt2 (2.0 equiv.) with C8BEADiBTP-H2 as the pro-ligand under similar synthetic methods in good yield. Single-crystal X-ray diffraction indicates that 3 is a bimetallic aluminum dimethyl complex with a tetradentate C8BEADiBTP moiety chelating two metal atoms, whereas complex 4 displays the dinuclear feature containing both tetra- and penta-coordinated zinc atoms bonded by one ONNON-pentadentate C8BEADiBTP ligand. Catalytic studies for ring-opening polymerization of ε-caprolactone of complex 1-4 were systematic explored; the comparative studies of such polymerization were also discussed.

Corrosion Protection of Al/Au/ZnO Anode for Hybrid Cell Application

PubMed Central

Slaughter, Gymama; Stevens, Brian

2015-01-01

Effective protection of power sources from corrosion is critical in the development of abiotic fuel cells, biofuel cells, hybrid cells and biobateries for implantable bioelectronics. Corrosion of these bioelectronic devices result in device inability to generate bioelectricity. In this paper Al/Au/ZnO was considered as a possible anodic substrate for the development of a hybrid cell. The protective abilities of corrosive resistant aluminum hydroxide and zinc phosphite composite films formed on the surface of Al/Au/ZnO anode in various electrolyte environments were examined by electrochemical methods. The presence of phosphate buffer and physiological saline (NaCl) buffer allows for the formation of aluminum hyrdroxide and zinc phosphite composite films on the surface of the Al/Au/ZnO anode that prevent further corrosion of the anode. The highly protective films formed on the Al/Au/ZnO anode during energy harvesting in a physiological saline environment resulted in 98.5% corrosion protective efficiency, thereby demonstrating that the formation of aluminum hydroxide and zinc phosphite composite films are effective in the prevention of anode corrosion during energy harvesting. A cell assembly consisting of the Al/Au/ZnO anode and platinum cathode resulted in an open circuit voltage of 1.03 V. A maximum power density of 955.3 μW/ cm2 in physiological saline buffer at a cell voltage and current density of 345 mV and 2.89 mA/ cm2, respectively. PMID:26580661

Corrosion Protection of Al/Au/ZnO Anode for Hybrid Cell Application.

PubMed

Slaughter, Gymama; Stevens, Brian

2015-11-16

Effective protection of power sources from corrosion is critical in the development of abiotic fuel cells, biofuel cells, hybrid cells and biobateries for implantable bioelectronics. Corrosion of these bioelectronic devices result in device inability to generate bioelectricity. In this paper Al/Au/ZnO was considered as a possible anodic substrate for the development of a hybrid cell. The protective abilities of corrosive resistant aluminum hydroxide and zinc phosphite composite films formed on the surface of Al/Au/ZnO anode in various electrolyte environments were examined by electrochemical methods. The presence of phosphate buffer and physiological saline (NaCl) buffer allows for the formation of aluminum hyrdroxide and zinc phosphite composite films on the surface of the Al/Au/ZnO anode that prevent further corrosion of the anode. The highly protective films formed on the Al/Au/ZnO anode during energy harvesting in a physiological saline environment resulted in 98.5% corrosion protective efficiency, thereby demonstrating that the formation of aluminum hydroxide and zinc phosphite composite films are effective in the prevention of anode corrosion during energy harvesting. A cell assembly consisting of the Al/Au/ZnO anode and platinum cathode resulted in an open circuit voltage of 1.03 V. A maximum power density of 955.3 mW/ cm² in physiological saline buffer at a cell voltage and current density of 345 mV and 2.89 mA/ cm², respectively.

AFM AND XPS Characterization of Zinc-Aluminum Alloy Coatings with Attention to Surface Dross and Flow Lines

NASA Astrophysics Data System (ADS)

Harding, Felipe A.; Alarcon, Nelson A.; Toledo, Pedro G.

Surfaces of various zinc-aluminum alloy (Zn-Al) coated steel samples are studied with attention to foreign surface dross by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS/ESCA). AFM topographic maps of zinc-aluminum alloy surfaces free of dross reveal the perfect nanoscale details of two kinds of dendrites: branched and globular. In all magnifications the dendrites appear smooth and, in general, very clean. XPS analysis of the extreme surface of a Zn-Al sample reveals Al, Zn, Si and O as the main components. The XPS results show no segregation or separation of phases other than those indicated by the ternary Al-Zn-Si diagram. For surfaces of Zn-Al plagued with impurities, high resolution AFM topographic maps reveal three situations: (1) areas with well-defined dendrites, relatively free of dross; (2) areas with small, millimeter-sized black spots known as dross; and (3) areas with large black stains, known as flow lines. Dendrite deformation and dross accumulation increase notably in the neighborhood, apparently clean to the naked eye, of dross or flow lines. XPS results of areas with dross and flow lines indicate unacceptable high concentration of Si and important Si phase separation. These results, in the light of AFM work, reveal that dross and flow lines are a consequence of a high local concentration of Si from high melting point silica and silicate impurities in the Zn-Al alloy source.

Role of iron and aluminum coagulant metal residuals and lead release from drinking water pipe materials.

PubMed

Knowles, Alisha D; Nguyen, Caroline K; Edwards, Marc A; Stoddart, Amina; McIlwain, Brad; Gagnon, Graham A

2015-01-01

Bench-scale experiments investigated the role of iron and aluminum residuals in lead release in a low alkalinity and high (> 0.5) chloride-to-sulfate mass ratio (CSMR) in water. Lead leaching was examined for two lead-bearing plumbing materials, including harvested lead pipe and new lead: tin solder, after exposure to water with simulated aluminum sulfate, polyaluminum chloride and ferric sulfate coagulation treatments with 1-25-μM levels of iron or aluminum residuals in the water. The release of lead from systems with harvested lead pipe was highly correlated with levels of residual aluminum or iron present in samples (R(2) = 0.66-0.88), consistent with sorption of lead onto the aluminum and iron hydroxides during stagnation. The results indicate that aluminum and iron coagulant residuals, at levels complying with recommended guidelines, can sometimes play a significant role in lead mobilization from premise plumbing.

Electrochemical behavior of tube-fin assembly for an aluminum automotive condenser with improved corrosion resistance

NASA Astrophysics Data System (ADS)

Pech-Canul, M. A.; Guía-Tello, J. C.; Pech-Canul, M. I.; Aguilar, J. C.; Gorocica-Díaz, J. A.; Arana-Guillén, R.; Puch-Bleis, J.

An aluminum automotive condenser was designed to exhibit high corrosion resistance in the seawater acetic acid test (SWAAT) combining zinc coated microchannel tubes and fins made with AA4343/AA3003(Zn)/AA4343 brazing sheet. Electrochemical measurements in SWAAT solution were carried out under laboratory conditions using tube-fin assembly and individual fin and tube samples withdrawn from the condenser core. The aim was to gain information on the protective role of the zinc sacrificial layer and about changes in corrosion behavior as a function of immersion time. External corrosion of the tube-fin system was simulated by immersion of mini-core samples under open circuit conditions. The corrosion rate increased rapidly during the first 6 h and slowly afterwards. The short time behavior was related to the dissolution of the oxide film and fast dissolution of the outermost part of the zinc diffusion layer. With the aid of cross-sectional depth corrosion potential profiles, it was shown that as the sacrificial layer gets dissolved, the surface concentration of zinc decreases and the potential shifts to less negative values. The results of galvanic coupling of tube and fins in a mini-cell showed that the tube became the anode while the fins exhibited cathodic behavior. An evolution in the galvanic interaction was observed, due to the progressive dissolution of the sacrificial zinc layer. The difference of uncoupled potentials between tube and fins decreased from 71 mV to 32 mV after 84 h of galvanic coupling. At the end of such period there was still a part of the zinc sacrificial layer remaining which would serve for protection of the tube material for even longer periods and there were indications of slight corrosion in the fins.

{l_angle}110{r_angle} dendrite growth in aluminum feathery grains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henry, S.; Rappaz, M.; Jarry, P.

1998-11-01

Automatic indexing of electron backscattered diffraction patterns, scanning electron microscopy, and optical microscopy observations have been carried out on aluminum-magnesium-silicon, aluminum-copper, and aluminum-silicon alloys directionally solidified or semicontinuously cast using the direct chill casting process. From these combined observations, it is shown that the feathery grains are made of {l_angle}110{r_angle} primary dendrite trunks (e.g., [011{bar 1}]) split in their centers by a coherent (111) twin plane. The average spacing of the dendrite trunks in the twin plane (about 10 to 20 {micro}m) is typically one order of magnitude smaller than that separating successive rows of trunks (or twin planes). Themore » [011{bar 1}] orientation of these trunks is close to the thermal gradient direction (typically within 15 deg)--a feature probably resulting from a growth competition mechanism similar to that occurring during normal <100> columnar dendrite growth. On both sides of these trunks, secondary dendrite arms also grow along {l_angle}110{r_angle} directions. Their impingement creates wavy noncoherent twin boundaries between the coherent twin planes. In the twin plane, evidence is shown that {l_angle}110{r_angle} branching mechanisms lead to the propagation of the twinned regions, to the regular arrangement of the primary dendrite trunks along a [{bar 2}11] direction, and to coherent planar twin boundaries. From these observations, it is concluded that the feathery grains are probably the result of a change from a normal <100> to a {l_angle}110{r_angle} surface tension/attachment kinetics anisotropy growth mode. Finally, the proposed mechanisms of leathery grain growth are further supported by the observation of {l_angle}110{r_angle} dendrite growth morphologies in thin aluminum-zinc coatings.« less

Factors that Influence the Price of Al, Cd, Co, Cu, Fe, Ni, Pb, Rare Earth Elements, and Zn

USGS Publications Warehouse

Papp, John F.; Bray, E. Lee; Edelstein, Daniel L.; Fenton, Michael D.; Guberman, David E.; Hedrick, James B.; Jorgenson, John D.; Kuck, Peter H.; Shedd, Kim B.; Tolcin, Amy C.

2008-01-01

This report is based on a presentation delivered at The 12th International Battery Materials Recycling Seminar, March 17-20, 2008, Fort Lauderdale, Fla., about the factors that influence prices for aluminum, cadmium, cobalt, copper, iron, lead, nickel, rare earth elements, and zinc. These are a diverse group of metals that are of interest to the battery recycling industry. Because the U.S. Geological Survey (USGS) closely monitors, yet neither buys nor sells, metal commodities, it is an unbiased source of metal price information and analysis. The authors used information about these and other metals collected and published by the USGS (U.S. production, trade, stocks, and prices and world production) and internationally (consumption and stocks by country) from industry organizations, because metal markets are influenced by activities and events over the entire globe. Long-term prices in this report, represented by unit values, were adjusted to 1998 constant dollars to remove the effects of inflation. A previous USGS study in this subject area was 'Economic Drivers of Mineral Supply' by Lorie A. Wagner, Daniel E. Sullivan, and John L. Sznopek (USGS Open File Report 02-335). By seeking a common cause for common behavior of prices among the various metal commodities, the authors found that major factors that influence prices of metal commodities were international events such as wars and recessions, and national events such as the dissolution of the Soviet Union in 1991 and economic growth in China, which started its open door policy in the 1970s but did not have significant market impact until the 1990s. Metal commodity prices also responded to commodity-specific events such as tariff or usage changes or mine strikes. It is shown that the prices of aluminum, cadmium, copper, iron, lead, nickel, and zinc are at historic highs, that world stocks are at (or near) historic lows, and that China's consumption of these metals had increased substantially, making it the world's leading consumer of these metals.

Zinc halogen battery electrolyte composition with lead additive

DOEpatents

Henriksen, Gary L.

1981-01-01

This disclosure relates to a zinc halogen battery electrolyte composition containing an additive providing improved zinc-on-zinc recyclability. The improved electrolyte composition involves the use of a lead additive to inhibit undesirable irregular plating and reduce nodular or dendritic growth on the electrode surface. The lead-containing electrolyte composition of the present invention appears to influence not only the morphology of the base plate zinc, but also the morphology of the zinc-on-zinc replate. In addition, such lead-containing electrolyte compositions appear to reduce hydrogen formation.

Possible role of zinc in diminishing lead-related occupational stress-a zinc nutrition concern.

PubMed

Wani, Ab Latif; Ahmad, Ajaz; Shadab, G G H A; Usmani, Jawed Ahmad

2017-03-01

Lead and zinc are mostly present at the same occupational source and usually found as co-contaminants. Lead is known to associate with detrimental effects to humans. Zinc however is an essential nutrient and its deficiency causes debilitating effects on growth and development. Besides, it acts as core ion of important enzymes and proteins. The purpose of this study was to examine if zinc concentrations are associated with blood lead levels and if zinc may prevent lead-induced DNA damage. Blood samples were collected from 92 workers as participants occupationally exposed to lead or lead and zinc and 38 comparison participants having no history of such exposure. Lead and zinc levels were determined from blood by atomic absorption spectrophotometry and genetic damage was assessed by comet assay. Correlation was calculated by Spearman's rho. Lead concentrations were observed to increase among workers with increase in years of exposure. There was a significant difference (p < 0.001) in blood lead levels between workers and controls. In addition, significant difference (p < 0.001) in the genetic damage was observed among workers and controls. A clear effect of increased occupational exposure was visible among workers. Multiple regression analysis further reveals the positive effect of lead, while as the inverse effect of zinc on DNA damage. The results suggest that zinc may influence body lead absorption and may have a role in preventing the genetic damage caused by lead.

Cadmium Alternatives: Zinc-Nickel Electroplating & Repair of Aluminum Coatings

DTIC Science & Technology

2008-02-27

Brighteners and Other Additives to Create Low Embrittling Plating Process • Based on Successful Test Results an LHE Alkaline Zn-Ni Formula was Selected for...Corrosion Testing (Salt Spray and Galvanic) – Fluid Immersion (ASTM F 483) Lubricity (Fasteners)– – Strippability • Ammonium Nitrate (pH 10...Considered – LDC 5030 Sn-Zn and SIFCO 4018 Zn-Ni • LDC 5030 Sn-Zn Selected Because of No-Bake Hydrogen Embrittlement Performance • Aluminum Surface

Experiments On Transparent Conductive Films For Spacecraft

NASA Technical Reports Server (NTRS)

Perez-Davis, Marla E.; Rutledge, Sharon K.; De Groh, Kim K.; Hung, Ching-Cheh; Malave-Sanabria, Tania; Hambourger, Paul; Roig, David

1995-01-01

Report describes experiments on thin, transparent, electrically conductive films made, variously, of indium tin oxide covered by magnesium fluoride (ITO/MgF2), aluminum-doped zinc oxide (AZO), or pure zinc oxide (ZnO). Films are candidates for application to such spacecraft components, including various optoelectronic devices and window surfaces that must be protected against buildup of static electric charge. On Earth, such films useful on heat mirrors, optoelectronic devices, gas sensors, and automotive and aircraft windows.

Metals in wine--impact on wine quality and health outcomes.

PubMed

Tariba, Blanka

2011-12-01

Metals in wine can originate from both natural and anthropogenic sources, and its concentration can be a significant parameter affecting consumption and conservation of wine. Since metallic ions have important role in oxide-reductive reactions resulting in wine browning, turbidity, cloudiness, and astringency, wine quality depends greatly on its metal composition. Moreover, metals in wine may affect human health. Consumption of wine may contribute to the daily dietary intake of essential metals (i.e., copper, iron, and zinc) but can also have potentially toxic effects if metal concentrations are not kept under allowable limits. Therefore, a strict analytical control of metal concentration is required during the whole process of wine production. This article presents a critical review of the existing literature regarding the measured metal concentration in wine, methods applied for their determination, and possible sources, as well as their impact on wine quality and human health. The main focus is set on aluminum, arsenic, cadmium, chromium, copper, iron, manganese, nickel, lead, and zinc, as these elements most often affect wine quality and human health.

Influence of coal ash and slag dumping on dump waste waters of the Kostolac power plants (Serbia)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popovic, A.; Djinovic, J.

2006-10-01

The content of selected trace and major elements in the river water used for transport, as well as in the subcategories of the waste waters (overflow and drainage) were analyzed in order to establish the influence of transport and dumping of coal ash and slag from the 'Kostolac A' and 'Kostolac B' power plants located 100 km from Belgrade (Serbia). It was found that during transport of coal ash and slag to the dump, the water used for transport becomes enriched with manganese, nickel, zinc, chromium, vanadium, titanium, cobalt, arsenic, aluminum, and silicon, while more calcium, iron, cadmium, and leadmore » are adsorbed by the ash and slag than is released from them. There is also an equilibrium between the release and adsorption processes of copper and magnesium during transport. The vertical penetration of the water used for transport results in a release of calcium, magnesium, manganese, and cadmium to the environment, while iron, nickel, zinc, chromium, copper, lead, vanadium, titanium, cobalt, and arsenic are adsorbed by the fractions of coal ash and slag in the dump.« less

Occurrence and variability of mining-related lead and zinc in the Spring River flood plain and tributary flood plains, Cherokee County, Kansas, 2009--11

USGS Publications Warehouse

Juracek, Kyle E.

2013-01-01

Historical mining activity in the Tri-State Mining District (TSMD), located in parts of southeast Kansas, southwest Missouri, and northeast Oklahoma, has resulted in a substantial ongoing input of cadmium, lead, and zinc to the environment. To provide some of the information needed to support remediation efforts in the Cherokee County, Kansas, superfund site, a 4-year study was begun in 2009 by the U.S. Geological Survey that was requested and funded by the U.S. Environmental Protection Agency. A combination of surficial-soil sampling and coring was used to investigate the occurrence and variability of mining-related lead and zinc in the flood plains of the Spring River and several tributaries within the superfund site. Lead- and zinc-contaminated flood plains are a concern, in part, because they represent a long-term source of contamination to the fluvial environment. Lead and zinc contamination was assessed with reference to probable-effect concentrations (PECs), which represent the concentrations above which adverse aquatic biological effects are likely to occur. The general PECs for lead and zinc were 128 and 459 milligrams per kilogram, respectively. The TSMD-specific PECs for lead and zinc were 150 and 2,083 milligrams per kilogram, respectively. Typically, surficial soils in the Spring River flood plain had lead and zinc concentrations that were less than the general PECs. Lead and zinc concentrations in the surficial-soil samples were variable with distance downstream and with distance from the Spring River channel, and the largest lead and zinc concentrations usually were located near the channel. Lead and zinc concentrations larger than the general or TSMD-specific PECs, or both, were infrequent at depth in the Spring River flood plain. When present, such contamination typically was confined to the upper 2 feet of the core and frequently was confined to the upper 6 inches. Tributaries with few or no lead- and zinc-mined areas in the basin—Brush Creek, Cow Creek, and Shawnee Creek—generally had flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) that were substantially less than the general PECs. Tributaries with extensive lead- and zinc-mined areas in the basin—Shoal Creek, Short Creek, Spring Branch, Tar Creek, Turkey Creek, and Willow Creek—had flood-plain lead concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general and TSMD-specific PECs. Likewise, the tributaries with extensive lead- and zinc-mined areas in the basin had flood-plain zinc concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general PEC. With the exception of Shoal and Willow Creeks, zinc concentrations typically exceeded the TSMD-specific PEC. The largest flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) were measured for Short and Tar Creeks. Lead and zinc concentrations in the surficial-soil samples collected from the tributary flood plains varied longitudinally in relation to sources of mining-contaminated sediment in the basins. Lead and zinc concentrations also varied with distance from the channel; however, no consistent spatial trend was evident. For the surficial-soil samples collected from the Spring River flood plain and tributary flood plains, both the coarse (larger than 63 micrometers) and fine particles (less than 63 micrometers) contained substantial lead and zinc concentrations.

An in vitro radiographic analysis of the density of dental luting cements as measured by CCD-based digital radiography.

PubMed

Antonijevic, Djordje; Jevremovic, Danimir; Jovanovic, Svetlana; Obradovic-Djuricic, Kosovka

2012-05-01

According to the ISO, the radiopacity of luting cements should be equal to or greater than that of aluminum. The aim of this in vitro study was to determine the radiopacity of 13 commercially available dental luting cements and compare them with human enamel and dentin. Five classes of luting cements were evaluated: zinc phosphate (Cegal N and Harvard Zinc Phosphate), zinc polycarboxylate (Harvard Polycarboxylate and Hoffmann's Carboxylate), glass ionomers (Ketac Cem Easymix, Ketac Cem Radiopaque, and Fuji I), resin-modified glass ionomer (Rely X Luting), and resin cements (Multilink Automix, Variolink II, Speed CEM, Rely X Unicem Automix, and three shades of Variolink Veneer). Tooth slices served as controls. Five specimens of each material measuring 8 mm in diameter and 1 mm thick were prepared and radiographed alongside tooth slices and an aluminum stepwedge using a Trophy RVG sensor. The radiopacity values were expressed in mm Al and analyzed by the ANOVA and Tukey tests (P < .05). All the cements examined except Variolink Veneer had significantly higher radiopacities than that of dentin. Rely X Unicem Automix, glass ionomer, and resin-modified glass-ionomer cements demonstrated radiopacities that were not significantly different with respect to enamel. Zinc phosphate, zinc polycarboxylate, and three of the resin cements presented radiopacity values that were significantly greater than that of enamel. Almost all the investigated materials presented an acceptable radiopacity. Radiopacity of dental cements seems to depend more on the presence of elements with high atomic numbers than on the type of the material.

40 CFR 467.25 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.190 0.079 TTO 0.090 Oil and grease (alternate...

40 CFR 467.25 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.190 0.079 TTO 0.090 Oil and grease (alternate...

40 CFR 467.25 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions... emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.190 0.079 TTO 0.090 Oil and grease (alternate...

Viscosity, density, and thermal conductivity of aluminum oxide and zinc oxide nanolubricants

PubMed Central

Kedzierski, M.A.; Brignoli, R.; Quine, K.T.; Brown, J.S.

2017-01-01

This paper presents liquid kinematic viscosity, density, and thermal conductivity measurements of eleven different synthetic polyolester-based nanoparticle nanolubricants (dispersions) at atmospheric pressure over the temperature range 288 K to 318 K. Aluminum oxide (Al2O3) and zinc oxide (ZnO) nanoparticles with nominal diameters of 127 nm and 135 nm, respectively, were investigated. A good dispersion of the spherical and non-spherical nanoparticles in the lubricant was maintained with a surfactant. Viscosity, density, and thermal conductivity measurements were made for the neat lubricant along with eleven nanolubricants with differing nanoparticle and surfactant mass fractions. Existing models were used to predict kinematic viscosity (±20%), thermal conductivity (±1%), and specific volume (±6%) of the nanolubricant as a function of temperature, nanoparticle mass fraction, surfactant mass fraction, and nanoparticle diameter. The liquid viscosity, density and thermal conductivity were shown to increase with respect to increasing nanoparticle mass fraction. PMID:28736463

Friction stir scribe welding technique for dissimilar joining of aluminium and galvanised steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Tianhao; Sidhar, Harpreet; Mishra, Rajiv S.

Friction stir scribe technology, a derivative of friction stir welding, was applied for the dissimilar lap welding of an aluminum alloy and galvanized mild steel sheets. During the process, the rotating tool with a cobalt steel scribe first penetrated the top material — aluminum — and then the scribe cut the bottom material — steel. The steel was displaced into the upper material to produce a characteristic hook feature. Lap welds were shear tested, and their fracture paths were studied. Welding parameters affected the welding features including hook height, which turned out to be highly related to fracture position. Therefore,more » in this paper, the relationships among welding parameters, hook height, joint strength and fracture position are presented. In addition, influence of zinc coating on joint strength was also studied. Keywords: friction stir scribe technology; dissimilar material welding; zinc coating; hook height; joint strength; fracture position« less

Aluminum Alloy and Article Cast Therefrom

NASA Technical Reports Server (NTRS)

Lee, Jonathan A. (Inventor); Chen, Po-Shou (Inventor)

2003-01-01

A cast article from an aluminum alloy, which has improved mechanical properties at elevated temperatures, has the following composition in weight percent: Silicon 14 - 25.0, Copper 5.5 - 8.0, Iron 0.05 - 1.2, Magnesium 0.5 - 1.5, Nickel 0.05 - 0.9, Manganese 0.05 - 1.0, Titanium 0.05 - 1.2, Zirconium 0.05 - 1.2, Vanadium 0.05 - 1.2, Zinc 0.05 - 0.9, Phosphorus 0.001 - 0.1, and the balance is Aluminum, wherein the silicon-to-magnesium ratio is 10 - 25, and the copper-to-magnesium ratio is 4 - 15. The aluminum alloy contains a simultaneous dispersion of three types of Al3X compound particles (X=Ti, V, Zr) having a LI2, crystal structure, and their lattice parameters are coherent to the aluminum matrix lattice. A process for producing this cast article is also disclosed, as well as a metal matrix composite, which includes the aluminum alloy serving as a matrix and containing up to about 60% by volume of a secondary filler material.

Color stable phosphors for LED lamps and methods for preparing them

DOEpatents

Murphy, James Edward; Setlur, Anant Achyut; Camardello, Samuel Joseph

2013-11-26

An LED lamp includes a light source configured to emit radiation with a peak intensity at a wavelength between about 250 nm and about 550 nm; and a phosphor composition configured to be radiationally coupled to the light source. The phosphor composition includes particles of a phosphor of formula I, said particles having a coating composition disposed on surfaces thereof; ((Sr.sub.1-zM.sub.z).sub.1-(x+w)A.sub.wCe.sub.x).sub.3(Al.sub.1-ySi.sub.y-)O.sub.4+y+3(x-w)F.sub.1-y-3(x-w) I wherein the coating composition comprises a material selected from aluminum oxide, magnesium oxide, calcium oxide, barium oxide, strontium oxide, zinc oxide, aluminum hydroxide, magnesium hydroxide, calcium hydroxide, barium hydroxide, strontium hydroxide, zinc hydroxide, aluminum phosphate, magnesium phosphate, calcium phosphate, barium phosphate, strontium phosphate, and combinations thereof; and A is Li, NA, K, or Rb, or a combination thereof; M is Ca, Ba, Mg, Zn, or a combination thereof; and 0

Theoretical Investigation of the Interfacial Reactions during Hot-Dip Galvanizing of Steel

NASA Astrophysics Data System (ADS)

Mandal, G. K.; Balasubramaniam, R.; Mehrotra, S. P.

2009-03-01

In the modern galvanizing line, as soon as the steel strip enters the aluminum-containing zinc bath, two reactions occur at the strip and the liquid-zinc alloy interface: (1) iron rapidly dissolves from the strip surface, raising the iron concentration in the liquid phase at the strip-liquid interface; and (2) aluminum forms a stable aluminum-iron intermetallic compound layer at the strip-coating interface due to its greater affinity toward iron. The main objective of this study is to develop a simple and realistic mathematical model for better understanding of the kinetics of galvanizing reactions at the strip and the liquid-zinc alloy interface. In the present study, a model is proposed to simulate the effect of various process parameters on iron dissolution in the bath, as well as, aluminum-rich inhibition layer formation at the substrate-coating interface. The transient-temperature profile of the immersed strip is predicted based on conductive and convective heat-transfer mechanisms. The inhibition-layer thickness at the substrate-coating interface is predicted by assuming the cooling path of the immersed strip consists of a series of isothermal holds of infinitesimal time-step. The influence of galvanizing reaction is assessed by considering nucleation and growth mechanisms at each hold time, which is used to estimate the total effect of the immersion time on the formation mechanism of the inhibition layer. The iron- dissolution model is developed based on well established principles of diffusion taking into consideration the area fraction covered by the intermetallic on the strip surface during formation of the inhibition layer. The model can be effectively used to monitor the dross formation in the bath by optimizing the process parameters. Theoretical predictions are compared with the findings of other researchers. Simulated results are in good agreement with the theoretical and experimental observation carried out by other investigators.

Electrocoagulation mechanism of perfluorooctanoate (PFOA) on a zinc anode: Influence of cathodes and anions.

PubMed

Wang, Yujuan; Lin, Hui; Jin, Fangyuan; Niu, Junfeng; Zhao, Jinbo; Bi, Ying; Li, Ying

2016-07-01

Batch experiments were conducted to investigate the effects of cathode materials and anions (Cl(-), SO4(2-), NO3(-), and CO3(2-)/HCO3(-)) on perfluorooctanoate (PFOA) removal in electrocoagulation process using zinc anode. The results indicated that the hydroxide flocs generated in-situ in the electrocoagulation process using the stainless steel rod as cathode were more effective than those using aluminum rod as cathode for the removal of PFOA after 20min of electrocoagulation at a current density of 0.5mAcm(-2). Hydroxide flocs generated in-situ in the electrocoagulation in the presence of Cl(-)/NO3(-) could effectively remove PFOA from aqueous solution with the removal ratios of 99.7%/98.1% and 98.9%/97.3% using stainless steel rod and aluminum rod as cathode, respectively. However, the PFOA removal ratios were 96.2%/4.1% and 7.4%/4.6% using stainless steel rod and aluminum rod as cathode, respectively, in the presence of SO4(2-) and CO3(2-)/HCO3(-). The different removal ratios of PFOA during the electrocoagulation process were primarily due to the fact that the hydroxide flocs generated in-situ were different in the presence of diverse cathodes and anions. We firstly demonstrated that Zn0.70Al0.30(OH)2(CO3)0.15·xH2O and ZnO generated in-situ in the electrocoagulation process (except for CO3(2-)/HCO3(-)) using zinc anode and aluminum/stainless steel rod cathode governed the sorption of PFOA. The adsorbent hydroxide flocs in-situ generated in the presence of Cl(-) could effectively remove PFOA from aqueous solution containing CO3(2-)/HCO3(-) anion at the initial hydroxide flocs concentration of 2000mgL(-1). These results provided an effective and alternative method to remove PFOA from aqueous solution containing CO3(2-)/HCO3(-) anion. Copyright © 2016 Elsevier B.V. All rights reserved.

Global supply and demand of metals in the future.

PubMed

Backman, Carl-Magnus

2008-01-01

This article is a short review on the subject of diminishing mineral resources in a world with increasing population. The concepts of reserves, resources, and life index are described. A forecast is made on the global consumption in the year 2050 of the metals iron (Fe), aluminum (Al), copper (Cu), zinc (Zn), nickel (Ni), and lead (Pb). Evidence indicates that a physical depletion of metals does not occur (fixed stock paradigm) but certain metals will become too expensive to extract (opportunity cost paradigm). The future demand for cadmium (Cd), mercury (Hg), arsenic (As), and selenium (Se) is presented. Finally, some metals presently of great interest for mineral prospectors that may have an important role in the future society are presented.

Improvement of Self-Heating of Indium Gallium Zinc Aluminum Oxide Thin-Film Transistors Using Al2O3 Barrier Layer

NASA Astrophysics Data System (ADS)

Jian, Li-Yi; Lee, Hsin-Ying; Lin, Yung-Hao; Lee, Ching-Ting

2018-02-01

To study the self-heating effect, aluminum oxide (Al2O3) barrier layers of various thicknesses have been inserted between the channel layer and insulator layer in bottom-gate-type indium gallium zinc aluminum oxide (IGZAO) thin-film transistors (TFTs). Each IGZAO channel layer was deposited on indium tin oxide (ITO)-coated glass substrate by using a magnetron radiofrequency cosputtering system with dual targets composed of indium gallium zinc oxide (IGZO) and Al. The 3 s orbital of Al cation provided an extra transport pathway and widened the conduction-band bottom, thus increasing the electron mobility of the IGZAO films. The Al-O bonds were able to sustain the oxygen stability of the IGZAO films. The self-heating behavior of the resulting IGZAO TFTs was studied by Hall measurements on the IGZAO films as well as the electrical performance of the IGZAO TFTs with Al2O3 barrier layers of various thicknesses at different temperatures. IGZAO TFTs with 50-nm-thick Al2O3 barrier layer were stressed by positive gate bias stress (PGBS, at gate-source voltage V GS = 5 V and drain-source voltage V DS = 0 V); at V GS = 5 V and V DS = 10 V, the threshold voltage shifts were 0.04 V and 0.2 V, respectively, much smaller than for the other IGZAO TFTs without Al2O3 barrier layer, which shifted by 0.2 V and 1.0 V when stressed under the same conditions.

Evaluation of metallized paint coatings for composite spacecraft structures

NASA Technical Reports Server (NTRS)

Brzuskiewicz, John E.

1990-01-01

The extreme temperature excursions of composite spacecraft structures in LEO must be minimized through the use of thermal-control coatings. Attention is presently given to tests of silicone resin coatings which were pigmented with either leafing aluminum or combinations of leafing aluminum with silicate-treated zinc oxide pigment. Atomic oxygen, UV/vacuum, and outgassing screening tests were conducted on several such coating formulations in order to characterize the performance characteristics of this coating concept. Performance was found to depend on pigment volume concentration.

Power Transfer Efficiency of Mutually Coupled Coils in an Aluminum AUV Hull

DTIC Science & Technology

2013-12-01

the tiles are made from a nickel -zinc material, a reasonable value is 20.0.r  38 Figure 24. Photograph of the ferrite board behind the...results were then compared to three sets of measured efficiency data: an IPT system without ferrite tiles; an IPT system with the receiving coil...attached to ferrite tiles; and an IPT system with the receiving coil/ ferrite tile combination placed inside an aluminum AUV hull. Efficiency was poor, less

Use of New Industrial Coatings for the U.S. Navy Waterfront Structures

DTIC Science & Technology

2008-12-01

utilized as a coating for the interior and exterior of piping systems, which either are located in harsh environments or are transporting substances with...typical application process, a separate set of test Table 7. MCU Coating Systems (SSPC SP 10 Surfaces) (5). SystelD CoatiIli System A Zinc -rich urethane...urethane/MID & AI-filled Urethane/MIO-filled urethane 315/315/314 336/336/336 340/340/336 ~ Micaceous iron oxide. \\) Aluminum. C Zinc . 12 as well as an

Hybrid Co-deposition of Mixed-Valent Molybdenum-Germanium Oxides (MoxGeyOz): A Route to Tunable Optical Transmission (Postprint)

DTIC Science & Technology

2015-08-05

to increased doping levels in indirect semiconductors [84]. The slope, and magnitude of the transmission curves continue to decrease alongside UL...periodically aluminium- doped zinc oxide thin films, Thin Solid Films 519 (2011) 2280–2286. [2] T. Minami, H. Nanto, S. Takata, Highly conductive and...transparent aluminum doped zinc oxide thin films prepared by RF magnetron sputtering, Jpn. J. Appl. Phys. 23 (1984) L280. [3] T. Minami, Present status of

Hollow spherical rotors fabricated by electroplating

NASA Technical Reports Server (NTRS)

Avery, H. W.; Conroy, T. F.

1966-01-01

Equatorial bands are fabricated to provide a locating fit for the hemispheres of hollow spherical rotors which are then jointed by electroplating. Several nonmagnetic materials may be used to form the joint, such as aluminum, copper, iron, gold, plantinum, and zinc.

40 CFR 467.65 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions... drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0.285 TTO 0.32 Oil and...

40 CFR 467.65 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions... drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0.285 TTO 0.32 Oil and...

40 CFR 467.65 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Drawing With Emulsions or Soaps... with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0.285 TTO 0.32 Oil and...

Removal of lead and zinc ions from water by low cost adsorbents.

PubMed

Mishra, P C; Patel, R K

2009-08-30

In this study, activated carbon, kaolin, bentonite, blast furnace slag and fly ash were used as adsorbent with a particle size between 100 mesh and 200 mesh to remove the lead and zinc ions from water. The concentration of the solutions prepared was in the range of 50-100 mg/L for lead and zinc for single and binary systems which are diluted as required for batch experiments. The effect of contact time, pH and adsorbent dosage on removal of lead and zinc by adsorption was investigated. The equilibrium time was found to be 30 min for activated carbon and 3h for kaolin, bentonite, blast furnace slag and fly ash. The most effective pH value for lead and zinc removal was 6 for activated carbon. pH value did not effect lead and zinc removal significantly for other adsorbents. Adsorbent doses were varied from 5 g/L to 20 g/L for both lead and zinc solutions. An increase in adsorbent doses increases the percent removal of lead and zinc. A series of isotherm studies was undertaken and the data evaluated for compliance was found to match with the Langmuir and Freundlich isotherm models. To investigate the adsorption mechanism, the kinetic models were tested, and it follows second order kinetics. Kinetic studies reveals that blast furnace slag was not effective for lead and zinc removal. The bentonite and fly ash were effective for lead and zinc removal.

The Reactive Stabilisation of Aluminum-Zinc-X Foams via the Formation of a Transient Liquid Phase Using the Powder Metallurgy Approach

NASA Astrophysics Data System (ADS)

Lafrance, Maxime

During the past few decades, aluminum foam research has focused on the improvement of properties. These properties include pore structure and process reproducibility. High energy absorption capacity, lightweight and high stiffness to weight ratio are some of the properties that make these foams desirable for a number of diverse applications. The use of a transient liquid phase and melting point depressant was studied in order to improve aluminum foam manufactured through the powder metallurgy process and to create reactive Stabilisation. The transient liquid phase reacts with aluminum and helps encapsulate higher levels of hydrogen, simultaneously reducing the difference between the melting point of the alloy and the gas release temperature of the blowing agent (TiH2). A large difference is known to adversely affect foam properties. The study of pure aluminum foam formation was undertaken to understand the basic foaming mechanisms related to crack formations under in-situ conditions. Elemental zinc powder at various concentrations (Al-10wt%Zn, Al-33wt%Zn and Al-50wt%Zn) was added to produce a transient liquid phase. Subsequently, an Al-12wt%Si pre-alloyed powder was added to the Al-Zn mixture in order to further reduce the melting point of the alloy and to increase the amount of transient liquid phase available (Al-3.59wtSi-9.6%Zn and Al-2.4wt%Si-9.7wt%Zn). The mechanical properties of each system at optimal foaming conditions were assessed and compared. It was determined that pure aluminum foam crack formation could be suppressed at higher heating rates, improving the structure through the nucleation of uniform pores. The Al-10wt%Zn foams generated superior pore properties, post maximum expansion stability and mechanical properties at lower temperatures, compared to pure aluminum. The Al-Si-Zn foams revealed remarkable stability and pore structure at very low temperatures (640 to 660°C). Overall, the Al-10wt%Zn and Al-3.59wt%Si-9.6wt%Zn foams offer superior properties compared to pure aluminum.

Quantitative Evaluation of Heavy Metals and Trace Elements in the Urinary Bladder: Comparison Between Cancerous, Adjacent Non-cancerous and Normal Cadaveric Tissue.

PubMed

Abdel-Gawad, Mahmoud; Elsobky, Emad; Shalaby, Mahmoud M; Abd-Elhameed, Mohamed; Abdel-Rahim, Mona; Ali-El-Dein, Bedeir

2016-12-01

The role of heavy metals and trace elements (HMTE) in the development of some cancers has been previously reported. Bladder carcinoma is a frequent malignancy of the urinary tract. The most common risk factors for bladder cancer are exposure to industrial carcinogens, cigarette smoking, gender, and possibly diet. The aim of this study was to evaluate HTME concentrations in the cancerous and adjacent non-cancerous tissues and compare them with those of normal cadaveric bladder. This prospective study included 102 paired samples of full-thickness cancer and adjacent non-cancerous bladder tissues of radical cystectomy (RC) specimens that were histologically proven as invasive bladder cancer (MIBC). We used 17 matched controls of non-malignant bladder tissue samples from cadavers. All samples were processed and evaluated for the concentration of 22 HMTE by using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Outcome analysis was made by the Mann-Whitney U, chi-square, Kruskal-Wallis, and Wilcoxon signed ranks tests. When compared with cadaveric control or cancerous, the adjacent non-cancerous tissue had higher levels of six elements (arsenic, lead, selenium, strontium, zinc, and aluminum), and when compared with the control alone, it had a higher concentration of calcium, cadmium, chromium, potassium, magnesium, and nickel. The cancerous tissue had a higher concentration of cadmium, lead, chromium, calcium, potassium, phosphorous, magnesium, nickel, selenium, strontium, and zinc than cadaveric control. Boron level was higher in cadaveric control than cancerous and adjacent non-cancerous tissue. Cadmium level was higher in cancerous tissue with node-positive than node-negative cases. The high concentrations of cadmium, lead, chromium, nickel, and zinc, in the cancerous together with arsenic in the adjacent non-cancerous tissues of RC specimens suggest a pathogenic role of these elements in BC. However, further work-up is needed to support this conclusion by the application of these HMTE on BC cell lines.

Auger spectroscopy analysis of lubrication with zinc dialkyldithiophosphate of several metal combinations in sliding contact

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1979-01-01

Sliding friction experiments were conducted with aluminum and other riders rubbing on disks of various elemental metals in the presence of a thin film of zinc dialkyldithiophosphate (ZDP). Auger emission spectroscopy was used to in situ monitor the changes in surface chemistry with rubbing under various loads. The metal disks examined included iron, titanium, rhodium, tungsten, molybdenum, and copper. For equivalent films of ZDP the film is a more effective lubricant for some metals than it is for others. The important active element in the compound varies with the metal lubricated and is a function of metal chemistry. The zinc in the ZDP is susceptible to electron beam induced desorption.

Battery resource assessment. Subtask 2.5: Battery manufacturing capability recycling of battery materials

NASA Astrophysics Data System (ADS)

Pemsler, P.

1981-02-01

Studies were conducted on the recycling of advanced battery system components for six different battery systems. These include: nickel/zinc, nickel/iron, zinc/chlorine, zinc/bromine, sodium/sulfur, and lithium-aluminum/iron sulfide. For each battery system, one or more processes were developed which would permit recycling of the major or active materials. Each recycle process was designed to produce a product material which can be used directly as a raw material by the battery manufacturer. Metal recoverabilities are in the range of 93 to 95% for all processes. In each case, capital and operating costs were developed for a recycling plant which processes 100,000 electric vehicle batteries per year.

Copper and zinc content in wild game shot with lead or non-lead ammunition – implications for consumer health protection

PubMed Central

Sommerfeld, Christine; Müller-Graf, Christine; Selhorst, Thomas; Greiner, Matthias; Gerofke, Antje; Ulbig, Ellen; Gremse, Carl; Spolders, Markus; Schafft, Helmut; Lahrssen-Wiederholt, Monika

2017-01-01

The aim of this study was to examine the contamination of game meat with copper and zinc and establish whether the use of alternative (non-lead) ammunition can lead to higher or unsafe levels of copper and zinc in the meat of roe deer, wild boar and red deer. The research project “Safety of game meat obtained through hunting” (LEMISI) was conducted in Germany with the purpose of examining the entry of lead as well as copper and zinc into the meat of hunted game when using either lead or non-lead ammunition. The outcome of this study shows that the usage of both lead-based ammunition and alternative non-lead ammunition results in the entry of copper and zinc into the edible parts of the game. Using non-lead ammunition does not entail dangerously elevated levels of copper and zinc, so replacing lead ammunition with alternative ammunition does not introduce a further health problem with regard to these metals. The levels of copper and zinc in game meat found in this study are in the range found in previous studies of game. The content of copper and zinc in game meat is also comparable to those regularly detected in meat and its products from livestock (pig, cattle, sheep) for which the mean human consumption rate is much higher. From the viewpoint of consumer health protection, the use of non-lead ammunition does not pose an additional hazard through copper and zinc contamination. A health risk due to the presence of copper and zinc in game meat at typical levels of consumer exposure is unlikely for both types of ammunition. PMID:28934259

Copper and zinc content in wild game shot with lead or non-lead ammunition - implications for consumer health protection.

PubMed

Schlichting, Daniela; Sommerfeld, Christine; Müller-Graf, Christine; Selhorst, Thomas; Greiner, Matthias; Gerofke, Antje; Ulbig, Ellen; Gremse, Carl; Spolders, Markus; Schafft, Helmut; Lahrssen-Wiederholt, Monika

2017-01-01

The aim of this study was to examine the contamination of game meat with copper and zinc and establish whether the use of alternative (non-lead) ammunition can lead to higher or unsafe levels of copper and zinc in the meat of roe deer, wild boar and red deer. The research project "Safety of game meat obtained through hunting" (LEMISI) was conducted in Germany with the purpose of examining the entry of lead as well as copper and zinc into the meat of hunted game when using either lead or non-lead ammunition. The outcome of this study shows that the usage of both lead-based ammunition and alternative non-lead ammunition results in the entry of copper and zinc into the edible parts of the game. Using non-lead ammunition does not entail dangerously elevated levels of copper and zinc, so replacing lead ammunition with alternative ammunition does not introduce a further health problem with regard to these metals. The levels of copper and zinc in game meat found in this study are in the range found in previous studies of game. The content of copper and zinc in game meat is also comparable to those regularly detected in meat and its products from livestock (pig, cattle, sheep) for which the mean human consumption rate is much higher. From the viewpoint of consumer health protection, the use of non-lead ammunition does not pose an additional hazard through copper and zinc contamination. A health risk due to the presence of copper and zinc in game meat at typical levels of consumer exposure is unlikely for both types of ammunition.

Quality of ground water in the Puget sound region, Washington, 1981

USGS Publications Warehouse

Turney, G.L.

1986-01-01

Groundwater from more than 100 sites in the Puget Sound region, Washington, was sampled and analyzed in 1981 for pH, specific conductance, and concentrations of fecal coliform bacteria, major ions, and dissolved iron, manganese, and nitrate. 20% of the samples were analyzed for concentrations of dissolved trace metals including aluminum, arsenic, barium, cadmium, chromium, copper, lead, mercury, selenium, silver, and zinc. The predominant water types were calcium bicarbonate and calcium-magnesium bicarbonate. Some wells in San Juan and Island Counties contained sodium chloride as a result of seawater intrusion. Dissolved solids concentrations were generally < 150 mg/L. Iron concentrations > 300 micrograms/L in 14% of all samples. Manganese concentrations > 50 micrograms/L in 40% of all samples. Trace-metal concentrations were generally < 10 mg/L , except for barium, copper, lead, and zinc. Nitrate concentrations were < 1.0 mg/L in water for over 75% of the sites. Concentrations > 1.0 mg/L in samples from Skagit, Whatcom , and Pierce Counties, were probably due to agricultural activities or septic tanks. Fecal coliform bacteria were detected in isolated instances. EPA drinking water regulations were exceeded only in isolated instances, except for widespread excessive iron and manganese concentrations. The historical data for the region were also evaluated for the same constituents. There are quantitative differences between historical and 1981 data, but they may be due to inconsistencies in data collection and analytical methods. (Author 's abstract)

Quality of ground water in the Columbia Basin, Washington, 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turney, G.L.

1986-01-01

Groundwater from 188 sites in the Columbia Basin of central Washington was sampled and analyzed in 1983 for pH, specific conductance, and concentrations of fecal coliform bacteria, major dissolved ions, and dissolved iron, manganese, and nitrate. Twenty of the samples were also analyzed for concentrations of dissolved trace metals including aluminum, arsenic, barium, cadmium, chromium, copper, lead, mercury, selenium, silver, and zinc. The predominant water types were sodium bicarbonate and calcium bicarbonate. The sodium bicarbonate water samples had higher pH, fluoride, and sodium:adsorption ratio values than samples with other water types. Most trace metal concentrations were also < 10 ug/Lmore » except for barium and zinc, which had maximum concentrations of 170 and 600 ug/L, respectively. Nitrate concentrations were < 1.0 mg/L in water from more than half the wells sampled. US EPA (Environmental Protection Agency) drinking water regulations were exceeded in several samples, most commonly involving pH and concentrations of fluoride, nitrate, and dissolved solids in samples from Adams and Grant Counties. Generally, the historical data lead to similar conclusions about the quality of groundwater in the Columbia Basin region. However, historical samples had higher dissolved solids concentrations in Douglas County. Historical samples also included fewer sodium bicarbonate type waters in the region as a whole than the 1983 samples. 24 refs., 2 figs., 4 tabs.« less

Association of urinary metal profiles with altered glucose levels and diabetes risk: a population-based study in China.

PubMed

Feng, Wei; Cui, Xiuqing; Liu, Bing; Liu, Chuanyao; Xiao, Yang; Lu, Wei; Guo, Huan; He, Meian; Zhang, Xiaomin; Yuan, Jing; Chen, Weihong; Wu, Tangchun

2015-01-01

Elevated heavy metals and fasting plasma glucose (FPG) levels were both associated with increased risk of cardiovascular diseases. However, studies on the associations of heavy metals and essential elements with altered FPG and diabetes risk were limited or conflicting. The objective of this study was to evaluate the potential associations of heavy metals and essential trace elements with FPG and diabetes risk among general Chinese population. We conducted a cross-sectional study to investigate the associations of urinary concentrations of 23 metals with FPG, impaired fasting glucose (IFG) and diabetes among 2242 community-based Chinese adults in Wuhan. We used the false discovery rate (FDR) method to correct for multiple hypothesis tests. After adjusting for potential confounders, urinary aluminum, titanium, cobalt, nickel, copper, zinc, selenium, rubidium, strontium, molybdenum, cadmium, antimony, barium, tungsten and lead were associated with altered FPG, IFG or diabetes risk (all P< 0.05); arsenic was only dose-dependently related to diabetes (P< 0.05). After additional adjustment for multiple testing, titanium, copper, zinc, selenium, rubidium, tungsten and lead were still significantly associated with one or more outcomes (all FDR-adjusted P< 0.05). Our results suggest that multiple metals in urine are associated with FPG, IFG or diabetes risk. Because the cross-sectional design precludes inferences about causality, further prospective studies are warranted to validate our findings.

Plating Inc. Site Fact Sheet: EPA to Begin Cleanup of Hazardous Waste

EPA Pesticide Factsheets

Hazardous waste cleanup and local community outreach around the Plating Inc. site at 888 N. Prior Ave.in St. Paul. The former industrial facility specialized in zinc and chromate plating of aluminum and is now abandoned.

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead Refining Wet Air Pollution... (pounds per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (i) Subpart G—Facility...

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead Refining Wet Air Pollution... (pounds per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (i) Subpart G—Facility...

78 FR 46948 - Proposed Agreement Regarding Site Costs and Covenants Not To Sue for American Lead and Zinc Mill...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

... Not To Sue for American Lead and Zinc Mill Site, Ouray County, Colorado AGENCY: Environmental... provides for Settling Party's payment of certain response costs incurred at the American Lead and Zinc Mill... reference the American Lead and Zinc Mill Site, the EPA Docket No. CERCLA-08-2013- 0004. The Agency's...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

Blood mineral concentrations in manatees (Trichechus manatus latirostris and Trichechus manatus manatus)

USGS Publications Warehouse

Siegal-Willott, J.; Harr, Kendal E.; Hall, Jeffery O.; Hayek, Lee-Ann C.; Auil-Gomez, Nicole; Powell, James A.; Bonde, Robert K.; Heard, Darryl

2013-01-01

Limited information is available regarding the role of minerals and heavy metals in the morbidity and mortality of manatees. Whole-blood and serum mineral concentrations were evaluated in apparently healthy, free-ranging Florida (Trichechus manatus latirostris, n = 31) and Belize (Trichechus manatus manatus, n = 14) manatees. Toxicologic statuses of the animals and of their environment had not been previously determined. Mean mineral whole-blood (WB) and serum values in Florida (FL) and Belize (BZ) manatees were determined, and evaluated for differences with respect to geographic location, relative age, and sex. Mean WB and serum silver, boron, cobalt, magnesium, molybdenum, and WB cadmium concentrations were significantly higher in BZ versus FL manatees (P ≤ 0.05). Mean WB aluminum, calcium, manganese, sodium, phosphorus, vanadium, and serum zinc concentrations were significantly lower in BZ versus FL manatees. Adult manatees had significant and higher mean WB aluminum, manganese, sodium, antimony, vanadium, and serum manganese and zinc concentrations compared to juvenile animals. Significant and lower mean WB and serum silver, boron, cobalt, and serum copper and strontium concentrations were present in adults compared to juveniles (P ≤ 0.05). Females had significant and higher mean WB nickel and serum barium compared to males (P ≤ 0.05). Mean WB arsenic and zinc, and mean serum iron, magnesium, and zinc concentrations fell within toxic ranges reported for domestic species. Results reveal manatee blood mineral concentrations differ with location, age, and sex. Influence from diet, sediment, water, and anthropogenic sources on manatee mineral concentration warrant further investigation.

Blood mineral concentrations in manatees (Trichechus manatus latirostris and Trichechus manatus manatus).

PubMed

Siegal-Willott, Jessica L; Harr, Kendal E; Hall, Jeffery O; Hayek, Lee-Ann C; Auil-Gomez, Nicole; Powell, James A; Bonde, Robert K; Heard, Darryl

2013-06-01

Limited information is available regarding the role of minerals and heavy metals in the morbidity and mortality of manatees. Whole-blood and serum mineral concentrations were evaluated in apparently healthy, free-ranging Florida (Trichechus manatus latirostris, n = 31) and Belize (Trichechus manatus manatus, n = 14) manatees. Toxicologic statuses of the animals and of their environment had not been previously determined. Mean mineral whole-blood (WB) and serum values in Florida (FL) and Belize (BZ) manatees were determined, and evaluated for differences with respect to geographic location, relative age, and sex. Mean WB and serum silver, boron, cobalt, magnesium, molybdenum, and WB cadmium concentrations were significantly higher in BZ versus FL manatees (P < 0.05). Mean WB aluminum, calcium, manganese, sodium, phosphorus, vanadium, and serum zinc concentrations were significantly lower in BZ versus FL manatees. Adult manatees had significant and higher mean WB aluminum, manganese, sodium, antimony, vanadium, and serum manganese and zinc concentrations compared to juvenile animals. Significant and lower mean WB and serum silver, boron, cobalt, and serum copper and strontium concentrations were present in adults compared to juveniles (P < or = 0.05). Females had significant and higher mean WB nickel and serum barium compared to males (P < or = 0.05). Mean WB arsenic and zinc, and mean serum iron, magnesium, and zinc concentrations fell within toxic ranges reported for domestic species. Results reveal manatee blood mineral concentrations differ with location, age, and sex. Influence from diet, sediment, water, and anthropogenic sources on manatee mineral concentration warrant further investigation.

25 CFR 215.21 - Payment of gross production tax on lead and zinc.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Payment of gross production tax on lead and zinc. 215.21 Section 215.21 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.21 Payment of gross production tax on lead and zinc. The superintendent of the Quapaw...

25 CFR 215.21 - Payment of gross production tax on lead and zinc.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Payment of gross production tax on lead and zinc. 215.21 Section 215.21 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.21 Payment of gross production tax on lead and zinc. The superintendent of the Quapaw...

Corrosion-Prevention Capabilities of a Water-Borne, Silicone-Based, Primerless Coating

NASA Technical Reports Server (NTRS)

Calle, Luz Marina; MacDowell, Louis G.; Vinje, Rubie D.

2005-01-01

Comparative tests have been performed to evaluate the corrosion-prevention capabilities of an experimental paint of the type described in Water-Borne, Silicone-Based, Primerless Paints, NASA Tech Briefs, Vol. 26, No. 11 (November 2002), page 30. To recapitulate: these paints contain relatively small amounts of volatile organic solvents and were developed as substitutes for traditional anticorrosion paints that contain large amounts of such solvents. An additional desirable feature of these paints is that they can be applied without need for prior application of primers to ensure adhesion. The test specimens included panels of cold-rolled steel, stainless steel 316, and aluminum 2024-T3. Some panels of each of these alloys were left bare and some were coated with the experimental water-borne, silicone-based, primerless paint. In addition, some panels of aluminum 2024-T3 and some panels of a fourth alloy (stainless steel 304) were coated with a commercial solvent-borne paint containing aluminum and zinc flakes in a nitrile rubber matrix. In the tests, the specimens were immersed in an aerated 3.5-weight-percent aqueous solution of NaCl for 168 hours. At intervals of 24 hours, the specimens were characterized by electrochemical impedance spectroscopy (EIS) and measurements of corrosion potentials. The specimens were also observed visually. As indicated by photographs of specimens taken after the 168-hour immersion (see figure), the experimental primerless silicone paint was effective in preventing corrosion of stainless steel 316, but failed to protect aluminum 2024-T3 and cold-rolled steel. The degree of failure was greater in the case of the cold-rolled steel. On the basis of visual observations, EIS, and corrosion- potential measurements, it was concluded that the commercial aluminum and zinc-filled nitrile rubber coating affords superior corrosion protection to aluminum 2024-T3 and is somewhat less effective in protecting stainless steel 304.

Concept Definition for the Pest Management Component of the Pollution Abatement Management System (PAMS).

DTIC Science & Technology

1982-01-01

able to obtain * Aluminum phosphide, Bromacil, Carbaryl (Sevin), Chlordane, Chlorpyrifos (Oursban), Diazinon, Dichlorovos (DODYP), Malathion, Paraquat...Pentachloro- phenol (PCP), Propoxur (Baygon), Thiram, strychnine/strychnine sulfate, zinc phosphide, and 2,4-D. 10 sufficient data to respond to

40 CFR Appendix V to Part 264 - Examples of Potentially Incompatible Waste

Code of Federal Regulations, 2013 CFR

2013-07-01

...; violent reaction. Group 2-A Aluminum Beryllium Calcium Lithium Magnesium Potassium Sodium Zinc powder... concentrated waste in Groups 1-A or 1-B Calcium Lithium Metal hydrides Potassium SO2 Cl2, SOCl2, PCl3, CH3 Si...

40 CFR Appendix V to Part 264 - Examples of Potentially Incompatible Waste

Code of Federal Regulations, 2014 CFR

2014-07-01

...; violent reaction. Group 2-A Aluminum Beryllium Calcium Lithium Magnesium Potassium Sodium Zinc powder... concentrated waste in Groups 1-A or 1-B Calcium Lithium Metal hydrides Potassium SO2 Cl2, SOCl2, PCl3, CH3 Si...

77 FR 64311 - Potential Market Impact of the Proposed Fiscal Year 2014 Annual Materials Plan; National Defense...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-19

...,000 (5) Cadmium Zinc Tellurium (CZT) substrates.. cm\\2\\ 24,000 (6) Lithium Cobalt Oxide (LCO) Kg 750 (6) Lithium Nickel Cobalt Aluminum Oxide kg 540 (6) (NCA). Mesocarbon Microbeads (MCMB) kg 648 (6...

40 CFR Appendix V to Part 264 - Examples of Potentially Incompatible Waste

Code of Federal Regulations, 2012 CFR

2012-07-01

...; violent reaction. Group 2-A Aluminum Beryllium Calcium Lithium Magnesium Potassium Sodium Zinc powder... concentrated waste in Groups 1-A or 1-B Calcium Lithium Metal hydrides Potassium SO2 Cl2, SOCl2, PCl3, CH3 Si...

Efficacy assessment of acid mine drainage treatment with coal mining waste using Allium cepa L. as a bioindicator.

PubMed

Geremias, Reginaldo; Bortolotto, Tiago; Wilhelm-Filho, Danilo; Pedrosa, Rozangela Curi; de Fávere, Valfredo Tadeu

2012-05-01

The aim of this study was to evaluate the efficacy of the treatment of acid mine drainage (AMD) with calcinated coal mining waste using Allium cepa L. as a bioindicator. The pH values and the concentrations of aluminum, iron, manganese, zinc, copper, lead and sulfate were determined before and after the treatment of the AMD with calcinated coal mining waste. Allium cepa L. was exposed to untreated and treated AMD, as well as to mineral water as a negative control (NC). At the end of the exposure period, the inhibition of root growth was measured and the mean effective concentration (EC(50)) was determined. Oxidative stress biomarkers such as lipid peroxidation (TBARS), protein carbonyls (PC), catalase activity (CAT) and reduced glutathione levels (GSH) in the fleshy leaves of the bulb, as well as the DNA damage index (ID) in meristematic cells, were evaluated. The results indicated that the AMD treatment with calcinated coal mining waste resulted in an increase in the pH and an expressive removal of aluminum, iron, manganese and zinc. A high sub-chronic toxicity was observed when Allium cepa L. was exposed to the untreated AMD. However, after the treatment no toxicity was detected. Levels of TBARS and PC, CAT activity and the DNA damage index were significantly increased (P<0.05) in Allium cepa L. exposed to untreated AMD when compared to treated AMD and also to negative controls. No significant alteration in the GSH content was observed. In conclusion, the use of calcinated coal mining waste associated with toxicological tests on Allium cepa L. represents an alternative system for the treatment and biomonitoring of these types of environmental contaminants. Copyright © 2011 Elsevier Inc. All rights reserved.

High energy density aluminum-oxygen cell

NASA Technical Reports Server (NTRS)

Rudd, E. J.; Gibbons, D. W.

1993-01-01

An alternative to a secondary battery as the power source for vehicle propulsion is a fuel cell. An example of this is the metal-air fuel cell using metals such as aluminum, zinc, or iron. Aluminum is a particularly attractive candidate, having high energy and power densities, being environmentally acceptable, and having a large, established industrial base for production and distribution. An aluminum-oxygen system is currently under development for a UUV test vehicle, and recent work has focussed upon low corrosion aluminum alloys and an electrolyte management system for processing the by-products of the energy-producing reactions. This paper summarizes the progress made in both areas. Anode materials capable of providing high utilization factors over current densities ranging from S to 150 mA/sq cm have been identified. These materials are essential to realizing an acceptable mission life for the UUV. With respect to the electrolyte management system, a filter/precipitator unit has been successfully operated for over 250 hours in a large scale, half-cell system.

Cadmiun and Zinc Adsorption by Acric Soils

NASA Astrophysics Data System (ADS)

da Silva, Luiz Gabriel; Colato, Alexandre; Casagrande, José Carlos; Soares, Marcio Roberto

2017-04-01

Acrodox soils are very weathered soils, characterized by having buildup of iron and aluminum oxides and hydroxides. These soils are present in extensive productive regions in the state of São Paulo. This work aimed at verifying the adequacy of constant capacitance model in describing the adsorption of cadmium and zinc in Anionic Rhodic Acrudox, Anionic Xanthic Acrudox and Rhodic Hapludalf. The chemical, mineralogical and physical attributes of these soils were determined in the layers 0-20 cm and 20-40 cm. Adsorption data of cadmium and zinc were also previously determined for samples of both layers of each soil. Were applied 5 mg dm-3 of cadmium and zinc to 2,0 g of soil to ample pH range (3 to 10) to build the adsorption envelops to three ionic strength. The constant capacitance model was adequate to simulate the adsorption of zinc and cadmium. It was not possible to make appropriate distinctions between measurements and simulations for two soil layers studied, neither between the three concentrations of background electrolyte.

Influence of annealing temperature on optical properties of Al doped ZnO nanoparticles via sol-gel methods

NASA Astrophysics Data System (ADS)

Rashid, Affa Rozana Abd; Hazwani, Tuan Nur; Mukhtar, Wan Maisarah; Taib, Nur Athirah Mohd

2018-06-01

Zinc oxide (ZnO) thin films have become technologically important materials due to their wide range of electrical and optical properties. The characteristics can be further adjusted by adequate doping processes. The effect of dopant concentration of Al, heating treatment and annealing in reducing atmosphere on the optical properties of the thin films is discussed. Undoped and aluminum-doped zinc oxide (AZO) thin films are prepared by the sol-gel method. Zinc acetate dihydrate, 2-methoxyethanol and monoethanolamine are used as precursor, solvent and stabilizer. In the case of AZO, aluminum nitrate nanohydrate is added to the precursor solution with an atomic percentage equal to 0 %, 1 %, 2 % and 3 % of Al. The multi thin layers are transformed into ZnO upon annealing at 450 °C and 500 °C. The optical properties such as transmittance, absorbance, band gap and refractive index of the thin films have been investigated by using UV-Visible Spectroscopy (UV-Vis). The results show that the effect of aluminium dopant concentration on the optical properties is depend on the post-heat treatment of the films. By doping with Al, the transmittance spectra in visible range increased and widen the band gap of ZnO which might due to Burstein-moss effects.

Salt Spray Test to Determine Galvanic Corrosion Levels of Electroless Nickel Connectors Mounted on an Aluminum Bracket

NASA Technical Reports Server (NTRS)

Rolin, T. D.; Hodge, R. E.; Torres, P. D.; Jones, D. D.; Laird, K. R.

2014-01-01

During preliminary vehicle design reviews, requests were made to change flight termination systems from an electroless nickel (EN) connector coating to a zinc-nickel (ZN) plating. The reason for these changes was due to a new NASA-STD-6012 corrosion requirement where connectors must meet the performance requirement of 168 hr of exposure to salt spray. The specification for class F connectors, MIL-DTL-38999, certifies the EN coating will meet a 48-hr salt spray test, whereas the ZN is certified to meet a 168-hr salt spray test. The ZN finish is a concern because Marshall Space Flight Center has no flight experience with ZN-finished connectors, and MSFC-STD-3012 indicates that zinc and zinc alloys should not be used. The purpose of this test was to run a 168-hr salt spray test to verify the electrical and mechanical integrity of the EN connectors and officially document the results. The salt spray test was conducted per ASTM B117 on several MIL-DTL-38999 flight-like connectors mounted to an aluminum 6061-T6 bracket that was alodined. The configuration, mounting techniques, electrical checks, and materials used were typical of flight and ground support equipment.

Thermal Pretreatment For TRU Waste Sorting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sasaki, T.; Aoyama, Y.; Miyamoto, Y.

2008-07-01

Japan Atomic Energy Agency conducted a study on thermal treatment of TRU waste to develop a removal technology for materials that are forbidden for disposal. The thermal pretreatment in which hot nitrogen and/or air is introduced to the waste is a process of removing combustibles, liquids, and low melting point metals from PVC wrapped TRU waste. In this study, thermal pretreatment of simulated waste was conducted using a desktop thermal treatment vessel and a laboratory scale thermal pretreatment system. Combustibles and low melting point metals are effectively separated from wastes by choosing appropriate temperature of flowing gases. Combustibles such asmore » papers, PVC, oil, etc. were removed and low melting point metals such as zinc, lead, and aluminum were separated from the simulated waste by the thermal pretreatment. (authors)« less

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... production Lead .000 .000 Zinc .000 .000 (b) Subpart G—Blast Furnace Wet Air Pollution Control. PSNS... pounds) of blast furnace lead bullion produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace...

40 CFR 421.76 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. PSNS Pollutant or... production Lead .000 .000 Zinc .000 .000 (b) Subpart G—Blast Furnace Wet Air Pollution Control. PSNS... pounds) of blast furnace lead bullion produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace...

X-ray microanalysis of the fingernails in term and preterm infants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sirota, L.; Straussberg, R.; Fishman, P.

1988-08-01

The element content of the fingernails of 10 term and 14 preterm infants, clipped for the first time after delivery, was determined by x-ray microanalysis. The results showed a decrease in sulfur and aluminum, and a higher chlorine content in term infants in comparison with preterm ones, the difference being statistically significant. Sodium, potassium, calcium, and zinc content did not differ in the two groups. Copper, iron, magnesium, aluminum, and phosphorus were detected in trace amounts only. Cobalt was not detected in the fingernails of newborns in either group. The elevated content of aluminum in the fingernails of preterm infantsmore » may be a clue to the osteopenia observed in these infants.« less

40 CFR 467.22 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emulsions Subcategory § 467.22 Effluent limitations representing the degree of effluent reduction attainable... off-lbs) of aluminum rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079...

40 CFR 467.22 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emulsions Subcategory § 467.22 Effluent limitations representing the degree of effluent reduction attainable... off-lbs) of aluminum rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079...

40 CFR 467.62 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emulsions or Soaps Subcategory § 467.62 Effluent limitations representing the degree of effluent reduction... off-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.680...

40 CFR 467.22 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emulsions Subcategory § 467.22 Effluent limitations representing the degree of effluent reduction attainable... off-lbs) of aluminum rolled with emulsions Chromium 0.057 0.024 Cyanide 0.038 0.016 Zinc 0.19 0.079...

40 CFR 467.62 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emulsions or Soaps Subcategory § 467.62 Effluent limitations representing the degree of effluent reduction... off-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.680...

40 CFR 467.63 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... or Soaps Subcategory § 467.63 Effluent limitations representing the degree of effluent reduction...-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.681 0...

40 CFR 467.62 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emulsions or Soaps Subcategory § 467.62 Effluent limitations representing the degree of effluent reduction... off-lbs) of aluminum drawn with emulsions or soaps Chromium 0.205 0.084 Cyanide 0.135 0.056 Zinc 0.680...

USE OF HYDROGEN RESPIROMETRY TO DETERMINE METAL TOXICITY TO SULFATE REDUCING BACTERIA

EPA Science Inventory

Acid mine drainage (AMD), an acidic metal-bearing wastewater poses a severe pollution problem attributed to post-mining activities. The metals (metal sulfates) encountered in AMD and considered of concern for risk assessment are: arsenic, cadmium, aluminum, manganese, iron, zinc ...

Optimization of the optical and electrical properties of electron beam evaporated aluminum-doped zinc oxide films for opto-electronic applications

NASA Astrophysics Data System (ADS)

Ali, H. M.; Abd El-Raheem, M. M.; Megahed, N. M.; Mohamed, H. A.

2006-08-01

Aluminum-doped zinc oxide (AZO) thin films have been deposited by electron beam evaporation technique on glass substrates. The structural, electrical and optical properties of AZO films have been investigated as a function of annealing temperature. It was observed that the optical properties such as transmittance, reflectance, optical band gap and refractive index of AZO films were strongly affected by annealing temperature. The transmittance values of 84% in the visible region and 97% in the NIR region were obtained for AZO film annealed at 475 °C. The room temperature electrical resistivity of 4.6×10-3 Ω cm has been obtained at the same temperature of annealing. It was found that the calculated refractive index has been affected by the packing density of the thin films, whereas, the high annealing temperature gave rise to improve the homogeneity of the films. The single-oscillator model was used to analyze the optical parameters such as the oscillator and dispersion energies.

Theoretic model and computer simulation of separating mixture metal particles from waste printed circuit board by electrostatic separator.

PubMed

Li, Jia; Xu, Zhenming; Zhou, Yaohe

2008-05-30

Traditionally, the mixture metals from waste printed circuit board (PCB) were sent to the smelt factory to refine pure copper. Some valuable metals (aluminum, zinc and tin) with low content in PCB were lost during smelt. A new method which used roll-type electrostatic separator (RES) to recovery low content metals in waste PCB was presented in this study. The theoretic model which was established from computing electric field and the analysis of forces on the particles was used to write a program by MATLAB language. The program was design to simulate the process of separating mixture metal particles. Electrical, material and mechanical factors were analyzed to optimize the operating parameters of separator. The experiment results of separating copper and aluminum particles by RES had a good agreement with computer simulation results. The model could be used to simulate separating other metal (tin, zinc, etc.) particles during the process of recycling waste PCBs by RES.

Homeostasis of metals in the progression of Alzheimer's disease.

PubMed

González-Domínguez, Raúl; García-Barrera, Tamara; Gómez-Ariza, José Luis

2014-06-01

In order to study the involvement of metals in the progression of Alzheimer's disease, serum samples from patients with Alzheimer and mild cognitive impairment were investigated. For this purpose, metal content was analyzed after size-fractionation of species and then, inter-element and inter-fraction ratios were computed. In this way, the analysis allowed discovering changes that could be used as markers of disease, but also provided a new insight into the interactions in the homeostasis of elements in neurodegeneration and its progression. Aluminum and labile forms of iron and copper were increased in demented patients, while manganese, zinc and selenium were reduced. Interestingly, levels of different elements, principally iron, aluminum and manganese, were closely inter-related, which could evidence a complex interdependency between the homeostasis of the different metals in this disorder. On the other hand, imbalances in metabolism of copper, zinc and selenium could be associated to abnormal redox status. Therefore, this study may contribute to our understanding of the pathological mechanisms related to metals in Alzheimer's disease.

Characterization of elemental and structural composition of corrosion scales and deposits formed in drinking water distribution systems.

PubMed

Peng, Ching-Yu; Korshin, Gregory V; Valentine, Richard L; Hill, Andrew S; Friedman, Melinda J; Reiber, Steve H

2010-08-01

Corrosion scales and deposits formed within drinking water distribution systems (DWDSs) have the potential to retain inorganic contaminants. The objective of this study was to characterize the elemental and structural composition of extracted pipe solids and hydraulically-mobile deposits originating from representative DWDSs. Goethite (alpha-FeOOH), magnetite (Fe(3)O(4)) and siderite (FeCO(3)) were the primary crystalline phases identified in most of the selected samples. Among the major constituent elements of the deposits, iron was most prevalent followed, in the order of decreasing prevalence, by sulfur, organic carbon, calcium, inorganic carbon, phosphorus, manganese, magnesium, aluminum and zinc. The cumulative occurrence profiles of iron, sulfur, calcium and phosphorus for pipe specimens and flushed solids were similar. Comparison of relative occurrences of these elements indicates that hydraulic disturbances may have relatively less impact on the release of manganese, aluminum and zinc, but more impact on the release of organic carbon, inorganic carbon, and magnesium. (c) 2010 Elsevier Ltd. All rights reserved.

Electrical and optical properties of p-type codoped ZnO thin films prepared by spin coating technique

NASA Astrophysics Data System (ADS)

Pathak, Trilok Kumar; Kumar, Vinod; Swart, H. C.; Purohit, L. P.

2016-03-01

Undoped, doped and codoped ZnO thin films were synthesized on glass substrates using a spin coating technique. Zinc acetate dihydrate, ammonium acetate and aluminum nitrate were used as precursor for zinc, nitrogen and aluminum, respectively. X-ray diffraction shows that the thin films have a hexagonal wurtzite structure for the undoped, doped and co-doped ZnO. The transmittance of the films was above 80% and the band gap of the film varied from 3.20 eV to 3.24 eV for undoped and doped ZnO. An energy band diagram to describe the photoluminescence from the thin films was also constructed. This diagram includes the various defect levels and possible quasi-Fermi levels. A minimum resistivity of 0.0834 Ω-cm was obtained for the N and Al codoped ZnO thin films with p-type carrier conductivity. These ZnO films can be used as a window layer in solar cells and in UV lasers.

Determination of small and large amounts of fluorine in rocks

USGS Publications Warehouse

Grimaldi, F.S.; Ingram, B.; Cuttitta, F.

1955-01-01

Gelatinous silica and aluminum ions retard the distillation of fluorine in the Willard and Winter distillation method. A generally applicable, simple method for the determination of fluorine in rocks containing aluminum or silicon or both as major constituents was desired. In the procedure developed, the sample is fused with a mixture of sodium carbonate and zinc oxide, leached with water, and filtered. The residue is granular and retains nearly all of the silica. The fluorine in the filtrate is distilled directly from a perchloric acid-phosphoric acid mixture. Phosphoric acid permits the quantitative distillation of fluorine in the presence of much aluminum at the usual distillation temperature and without the collection of large volumes of distillate. The fluorine is determined either by microtitration with thorium nitrate or colorimetrically with thoron. The procedure is rapid and has yielded excellent results on silicate rocks and on samples from the aluminum phosphate (leached) zone of the Florida phosphate deposits.

Influence of various thickness metallic interlayers on opto-electric and mechanical properties of AZO thin films on PET substrates

NASA Astrophysics Data System (ADS)

Chang, R. C.; Li, T. C.; Lin, C. W.

2012-02-01

Various thickness metallic interlayers to improve the opto-electric and mechanical properties of aluminum-doped zinc oxide (AZO) thin films deposited on flexible polyethylene terephtalate (PET) substrates are studied. The effects of the interlayers on the resistance and transmittance of the AZO thin films are discussed. The result shows that the metallic interlayers effectively improve the electric resistance but reduce the optical transmittance of the AZO thin films. These phenomena become more obvious as the interlayer thickness increases. However, the AZO with an aluminum interlayer still behaves an acceptable transmittance. Moreover, mechanical tests indicate that the aluminum interlayer increases the hardness and modulus, and reduce the residual stress of the AZO thin films. In contrast, the silver and copper interlayers decrease the AZO's mechanical properties. Comparing to those without any interlayer, the results show that the best interlayer is the 6 nm thick aluminum film.

Surface-Water Hydrology and Quality at the Pike Hill Superfund Site, Corinth, Vermont, October 2004 to December 2005

USGS Publications Warehouse

Kiah, Richard G.; Deacon, Jeffrey R.; Piatak, Nadine M.; Seal, Robert R.; Coles, James F.; Hammarstrom, Jane M.

2007-01-01

The hydrology and quality of surface water in and around the Pike Hill Brook watershed, in Corinth, Vermont, was studied from October 2004 to December 2005 by the U.S. Geological Survey in cooperation with the U.S. Environmental Protection Agency (USEPA). Pike Hill was mined intermittently for copper from 1847 to 1919 and the site is known to be contributing trace elements and acidity to Pike Hill Brook and an unnamed tributary to Cookville Brook. The site has been listed as a Superfund site since 2004. Streamflow, specific conductance, pH, and water temperature were measured continuously and monthly at three sites on Pike Hill Brook to determine the variation in these parameters over an annual cycle. Synoptic water-quality sampling was done at 10 stream sites in October 2004, April 2005, and June 2005 and at 13 stream sites in August 2005 to characterize the quality of surface water in the watershed on a seasonal and spatial basis, as well as to assess the effects of wetlands on water quality. Samples for analysis of benthic macroinvertebrate populations were collected at 11 stream sites in August 2005. Water samples were analyzed for 5 major ions and 32 trace elements. Concentrations of trace elements at sites in the Pike Hill Brook watershed exceeded USEPA National Recommended Water Quality Criteria acute and chronic toxicity standards for aluminum, iron, cadmium, copper, and zinc. Concentrations of copper exceeded the chronic criteria in an unnamed tributary to Cookville Brook in one sample. Concentrations of sulfate, calcium, aluminum, iron, cadmium, copper, and zinc decreased with distance from a site directly downstream from the mine (site 1), as a result of dilution and through sorption and precipitation of the trace elements. Maximum concentrations of aluminum, iron, cadmium, copper, and zinc were observed during spring snowmelt. Concentrations of sulfate, calcium, cadmium, copper, and zinc, and instantaneous loads of calcium and aluminum were statistically different (p<0.05) among the three continuously monitored sites (sites 1, 4, and 5). Instantaneous loads of aluminum, iron, and copper decreased by one to three orders of magnitude from site 1 to a site 1.1 mi downstream (site 4). Instantaneous loads of sulfate were similar between sites 1, 4, and at a site 3 mi downstream (site 5). Instantaneous loads of cadmium and zinc were similar between sites 1 and 4, and loads of iron and copper were similar between sites 4 and 5. Loads of chemical constituents were compared at site 1 (closest to the mine waste piles) and site 5 (near the mouth of Pike Hill Brook and below a majority of the wetlands). Annually, the loads of dissolved cadmium and zinc at site 1 were about five times greater than loads at site 5, and the load of dissolved copper at site 1 was about 17 times greater than at site 5. The ratio of loads for dissolved cadmium, copper, and zinc to total cadmium, copper, and zinc at site 1 was about 1. Samples collected in Pike Hill Brook upstream and downstream from the wetlands during low flows in August 2005 showed that oxidation of ferrous iron and precipitation of iron-hydroxides were probably not affecting trace metals in the wetlands through sorption; however, a significant portion of the iron entering the wetlands was in particulate form and may have transported sorbed copper and other trace metals. Thus, aerobic activity in the wetlands was probably not affecting metal cycling in the watershed. Concentrations and loads of sulfate may be unlikely to define unequivocally the role of the wetlands with regard to anaerobic bacterial sulfate reduction; however, bacterial sulfate removal may have affected loads of sulfate. Loads of copper increased downstream from the wetlands and may reflect the reductive dissolution of ferric hydroxide particulates in anaerobic parts of the wetlands.Concentrations of dissolved iron increased downstream from the wetlands. The most apparent effects on the macroinvertebr

Mineral content of smooth scallop (Flexopecten glaber) caught Canakkale, Turkey and evaluation in terms of food safety.

PubMed

Berik, Nermin; Çankırılıgil, Ekrem Cem; Gül, Güzin

2017-07-01

In this research, one of the most promising scallop species, smooth scallop (Flexopecten glaber) was studied. According to our findings, smooth scallop has beneficial micro and macro minerals, fat and carbohydrate just before the spawning. While the ratios protein, ash and water decreased from autumn to summer, ratio of crude fat increased till reproduction season in late spring and decreased in summer (P<0.05). In digestive glands, aluminum, bromine, cadmium, calcium, chromium, copper, iron, manganese, nickel, and zinc were detected more compared to adductor muscles (P<0.05). However; boron, magnesium and potassium were found more in adductor muscles (P<0.05) and there were no significant statistically differences in cobalt and lead (P>0.05). Most of the elements in the both tissues except K and Mg increased till summer. On the other hand, two of the most toxic metals, cadmium and aluminum were mostly accumulated in the digestive gland of smooth scallop. It is recommended that; digestive gland of scallops should be removed before consuming in terms of food safety. Besides, scallops are convenient to be processed, because of easy removal muscle tissue from internal organs. Copyright © 2017 Elsevier GmbH. All rights reserved.

Methods for collection and analysis of geopressured geothermal and oil field waters

USGS Publications Warehouse

Lico, Michael S.; Kharaka, Yousif K.; Carothers, William W.; Wright, Victoria A.

1982-01-01

Present methods are described for the collection, preservation, and chemical analysis of waters produced from geopressured geothermal and petroleum wells. Detailed procedures for collection include precautions and equipment necessary to ensure that the sample is representative of the water produced. Procedures for sample preservation include filtration, acidification, dilution for silica, methyl isobutyl ketone (MIBK) extraction of aluminum, addition of potassium permanganate to preserve mercury, and precipitation of carbonate species as strontium carbonate for stable carbon isotopes and total dissolved carbonate analysis. Characteristics determined at the well site are sulfide, pH, ammonia, and conductivity. Laboratory procedures are given for the analysis of lithium, sodium, potassium, rubidium, cesium, magnesium, calcium, strontium, barium, iron, manganese, zinc, lead, aluminum, .and mercury by atomic absorption and flame emission spectroscopy. Chloride is determined by silver nitrate titration and fluoride by ion-specific electrode. Bromide and iodide concentrations are determined by the hypochlorite oxidation method. Sulfate is analyzed by titration using barium chloride with thorin indicator after pretreatment with alumina. Boron and silica are determined colorimetrically by the carmine and molybdate-blue methods, respectively. Aliphatic acid anions (C2 through C5) are determined by gas chromatography after separation and concentration in a chloroform-butanol mixture.

Biofilters for stormwater harvesting: understanding the treatment performance of key metals that pose a risk for water use.

PubMed

Feng, Wenjun; Hatt, Belinda E; McCarthy, David T; Fletcher, Tim D; Deletic, Ana

2012-05-01

A large-scale stormwater biofilter column study was conducted to evaluate the impact of design configurations and operating conditions on metal removal for stormwater harvesting and protection of aquatic ecosystems. The following factors were tested over 8 months of operation: vegetation selection (plant species), filter media type, filter media depth, inflow volume (loading rate), and inflow pollutant concentrations. Operational time was also integrated to evaluate treatment performance over time. Vegetation and filter type were found to be significant factors for treatment of metals. A larger filter media depth resulted in increased outflow concentrations of iron, aluminum, chromium, zinc, and lead, likely due to leaching and mobilization of metals within the media. Treatment of all metals except aluminum and iron was generally satisfactory with respect to drinking water quality standards, while all metals met standards for irrigation. However, it was shown that biofilters could be optimized for removal of iron to meet the required drinking water standards. Biofilters were generally shown to be resilient to variations in operating conditions and demonstrated satisfactory removal of metals for stormwater-harvesting purposes. © 2012 American Chemical Society

Impact fragmentation of a brittle metal compact

NASA Astrophysics Data System (ADS)

Tang, Megan; Hooper, Joseph P.

2018-05-01

The fragmentation behavior of a metal powder compact which is ductile in compression but brittle in tension is studied via impact experiments and analytical models. Consolidated metal compacts were prepared via cold-isostatic pressing of <10 μm zinc powder at 380 MPa followed by moderate annealing at 365 °C. The resulting zinc material is ductile and strain-hardening in high-rate uniaxial compression like a traditional metal, but is elastic-brittle in tension with a fracture toughness comparable to a ceramic. Cylindrical samples were launched up to 800 m/s in a gas gun into thin aluminum perforation targets, subjecting the projectile to a complex multiaxial and time-dependent stress state that leads to catastrophic fracture. A soft-catch mechanism using low-density artificial snow was developed to recover the impact debris, and collected fragments were analyzed to determine their size distribution down to 30 μm. Though brittle fracture occurs along original particle boundaries, no power-law fragmentation behavior was observed as is seen in other low-toughness materials. An analytical theory is developed to predict the characteristic fragment size accounting for both the sharp onset of fragmentation and the effect of increasing impact velocity.

Investigation of electrode materials for alkaline batteries

NASA Technical Reports Server (NTRS)

Arcand, G. M.

1971-01-01

A number of amalgam electrode systems were investigated for possible use as high rate anodes and cathodes. The systems examined include: lithium, sodium, and potassium in Group 1, magnesium, calcium, and barium in Group 2, aluminum in Group 3, lead in Group 4, copper in Group 1b, and zinc and cadmium in Group 2b. The K(Hg) and Na(Hg) anodes in 10 VF and 15 VF (an unambiguous expression of concentration that indicates the number of formula weights of solute dissolved in a liter of solution) hydroxide solutions have proven satisfactory; some of these have produced current densities of more than 8 A/sq cm. None of the amalgam cathodes have approached this performance although the TI(Hg) has delivered 1 A/sq cm. Se(Hg) and Te(Hg) cathodes have given very stable discharges. Zn(Hg) and Cd(Hg) electrodes did not show good high rate characteristics, 200 to 300 mA/sq cm being about the maximum current densities obtainable. Both anodes are charged through a two-step process in which M(Hg) is first formed electrochemically and subsequently reduces Zn(II or Cd(II) to form the corresponding amalgam. The second step is extremely rapid for zinc and very slow for cadmium.

Quality of water and sediment in streams affected by historical mining, and quality of Mine Tailings, in the Rio Grande/Rio Bravo Basin, Big Bend Area of the United States and Mexico, August 2002

USGS Publications Warehouse

Lambert, Rebecca B.; Kolbe, Christine M.; Belzer, Wayne

2008-01-01

The U.S. Geological Survey, in cooperation with the International Boundary and Water Commission - U.S. and Mexican Sections, the National Park Service, the Texas Commission on Environmental Quality, the Secretaria de Medio Ambiente y Recursos Naturales in Mexico, the Area de Proteccion de Flora y Fauna Canon de Santa Elena in Mexico, and the Area de Proteccion de Flora y Fauna Maderas del Carmen in Mexico, collected samples of stream water, streambed sediment, and mine tailings during August 2002 for a study to determine whether trace elements from abandoned mines in the area in and around Big Bend National Park have affected the water and sediment quality in the Rio Grande/Rio Bravo Basin of the United States and Mexico. Samples were collected from eight sites on the main stem of the Rio Grande/Rio Bravo, four Rio Grande/Rio Bravo tributary sites downstream from abandoned mines or mine-tailing sites, and 11 mine-tailing sites. Mines in the area were operated to produce fluorite, germanium, iron, lead, mercury, silver, and zinc during the late 1800s through at least the late 1970s. Moderate (relatively neutral) pHs in stream-water samples collected at the 12 Rio Grande/Rio Bravo main-stem and tributary sites indicate that water is well mixed, diluted, and buffered with respect to the solubility of trace elements. The highest sulfate concentrations were in water samples from tributaries draining the Terlingua mining district. Only the sample from the Rough Run Draw site exceeded the Texas Surface Water Quality Standards general-use protection criterion for sulfate. All chloride and dissolved solids concentrations in water samples were less than the general-use protection criteria. Aluminum, copper, mercury, nickel, selenium, and zinc were detected in all water samples for which each element was analyzed. Cadmium, chromium, and lead were detected in samples less frequently, and silver was not detected in any of the samples. None of the sample concentrations of aluminum, cadmium, chromium, nickel, selenium, and zinc exceeded the Texas Surface Water Quality Standards criteria for aquatic life-use protection or human health. The only trace elements detected in the water samples at concentrations exceeding the Texas Surface Water Quality Standards criterion for human health (fish consumption use) was lead at one site and mercury at 10 of 12 sites. Relatively high mercury concentrations distributed throughout the area might indicate sources of mercury in addition to abandoned mining areas. Streambed-sediment samples were collected from 12 sites and analyzed for 44 major and trace elements. In general, the trace elements detected in streambed-sediment samples were low in concentration, interpreted as consistent with background concentrations. Concentrations at two sites, however, were elevated compared to Texas Commission on Environmental Quality criteria. Concentrations of antimony, arsenic, cadmium, lead, silver, and zinc in the sample from San Carlos Creek downstream from La Esperanza (San Carlos) Mine exceeded the Texas Commission on Environmental Quality screening levels for sediment. The sample from Rough Run Draw, downstream from the Study Butte Mine, also showed elevated concentrations of arsenic, cadmium, and lead, but these concentrations were much lower than those in the San Carlos Creek sample and did not exceed screening levels. Elevated concentrations of multiple trace elements in streambed-sediment samples from San Carlos Creek and Rough Run Draw indicate that San Carlos Creek, and probably Rough Run Draw, have been adversely affected by mining activities. Fourteen mine-tailing samples from 11 mines were analyzed for 25 major and trace elements. All trace elements except selenium and thallium were detected in one or more samples. The highest lead concentrations were detected in tailings samples from the Boquillas, Puerto Rico, La Esperanza (San Carlos), and Tres Marias Mines, as might be expected because the tailings ar

25 CFR 215.21 - Payment of gross production tax on lead and zinc.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Payment of gross production tax on lead and zinc. 215.21... ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.21 Payment of gross production tax on lead and zinc. The superintendent of the Quapaw Indian Agency is hereby authorized and directed to pay at the...

25 CFR 215.21 - Payment of gross production tax on lead and zinc.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Payment of gross production tax on lead and zinc. 215.21... ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.21 Payment of gross production tax on lead and zinc. The superintendent of the Quapaw Indian Agency is hereby authorized and directed to pay at the...

Assessment of Hair Aluminum, Lead, and Mercury in a Sample of Autistic Egyptian Children: Environmental Risk Factors of Heavy Metals in Autism.

PubMed

Mohamed, Farida El Baz; Zaky, Eman Ahmed; El-Sayed, Adel Bassuoni; Elhossieny, Reham Mohammed; Zahra, Sally Soliman; Salah Eldin, Waleed; Youssef, Walaa Yousef; Khaled, Rania Abdelmgeed; Youssef, Azza Mohamed

2015-01-01

The etiological factors involved in the etiology of autism remain elusive and controversial, but both genetic and environmental factors have been implicated. The aim of this study was to assess the levels and possible environmental risk factors and sources of exposure to mercury, lead, and aluminum in children with autism spectrum disorder (ASD) as compared to their matched controls. One hundred ASD children were studied in comparison to 100 controls. All participants were subjected to clinical evaluation and measurement of mercury, lead, and aluminum through hair analysis which reflects past exposure. The mean Levels of mercury, lead, and aluminum in hair of the autistic patients were significantly higher than controls. Mercury, lead, and aluminum levels were positively correlated with maternal fish consumptions, living nearby gasoline stations, and the usage of aluminum pans, respectively. Levels of mercury, lead, and aluminum in the hair of autistic children are higher than controls. Environmental exposure to these toxic heavy metals, at key times in development, may play a causal role in autism.

Assessment of Hair Aluminum, Lead, and Mercury in a Sample of Autistic Egyptian Children: Environmental Risk Factors of Heavy Metals in Autism

PubMed Central

Mohamed, Farida El Baz; Zaky, Eman Ahmed; El-Sayed, Adel Bassuoni; Elhossieny, Reham Mohammed; Zahra, Sally Soliman; Salah Eldin, Waleed; Youssef, Walaa Yousef; Khaled, Rania Abdelmgeed; Youssef, Azza Mohamed

2015-01-01

Background and Aims. The etiological factors involved in the etiology of autism remain elusive and controversial, but both genetic and environmental factors have been implicated. The aim of this study was to assess the levels and possible environmental risk factors and sources of exposure to mercury, lead, and aluminum in children with autism spectrum disorder (ASD) as compared to their matched controls. Methods. One hundred ASD children were studied in comparison to 100 controls. All participants were subjected to clinical evaluation and measurement of mercury, lead, and aluminum through hair analysis which reflects past exposure. Results. The mean Levels of mercury, lead, and aluminum in hair of the autistic patients were significantly higher than controls. Mercury, lead, and aluminum levels were positively correlated with maternal fish consumptions, living nearby gasoline stations, and the usage of aluminum pans, respectively. Conclusion. Levels of mercury, lead, and aluminum in the hair of autistic children are higher than controls. Environmental exposure to these toxic heavy metals, at key times in development, may play a causal role in autism. PMID:26508811

RESPIROMETRY AS A TOOL TO DETERMINE METAL TOXICITY IN A SULFATE REDUCING BACTERIAL CULTURE

EPA Science Inventory

A novel method under development for treatment of acid mine drainage waste uses biologically- generated hydrogen sulfide (H2S) to precipitate the metals in acid mine drainage (principally zinc, copper, aluminum, nickel, cadmium, arsenic, manganese, iron, and cobalt). The insolub...

Trace elements in canvasbacks (Aythya valisineria) wintering in Louisiana, USA, 1987-1988

USGS Publications Warehouse

Custer, Thomas W.; Hohman, William L.

1994-01-01

We determined trace element concentrations in livers of canvasbacks (Aythya valisineria) collected at Catahoula Lake and the Mississippi River Delta, Louisiana during, the winter of 1987–1988. Forty percent of canvasbacks wintering at Lake Catahoula had elevated concentrations of lead (>6·7 μg g−1 dry weight) in the liver; 33% had concentrations consistent with lead intoxication (>26·7 μg g−1). Based on the number of canvasbacks that winter at Lake Catahoula and the frequency of lead exposure there, more than 5% of the continental population of canvasbacks may be exposed to lead at Lake Catahoula alone. Lead concentrations in livers differed among months and were higher in males than females, but were not different in adults and immatures. Concentrations of selenium and mercury in livers of females differed among months but not by age or location. Cadmium concentrations in livers differed by age, location and month of collection, but not by sex. Frequencies and concentrations of trace elements not commonly associated with adverse effects on avian species (aluminum, arsenic, copper, iron, magnesium, manganese, nickel, silver, vanadium and zinc) are presented. Except for the elevated concentrations of lead at Catahoula Lake, all trace elements were at background concentrations.

The Levels of Trace Elements in Honey and Molasses Samples That Were Determined by ICP-OES After Microwave Digestion Method.

PubMed

Altundag, Huseyin; Bina, Emel; Altıntıg, Esra

2016-04-01

The aim of this study is determining the amount of Al, Cu, Fe, Mn, Ni, Pb and Zn in samples of molasses and honey which were gathered from the Sakarya and Istanbul regions. In this study, trace elements in 8 honey and 20 molasses samples with different botanic features were evaluated. The sample preparation phase was performed via wet decomposition method and microwave digestion system. The accuracy of the method was checked by the standard reference material; tea leaves (INCY-TL-1) and NIST-SRM 1515-apple. The concentrations of essential trace elements (TEs) were observed in the range of 1.61 ± 0.01-287.03 ± 1.07; 0.21 ± 0.01-11.04 ± 0.12; 0.35 ± 0.03-21.71 ± 0.02 and 1.19 ± 0.01-60.90 ± 1.09 μg g(-1) for iron, copper, manganese and zinc ions, respectively, while the toxic element contents were observed in the range of 0.82 ± 0.17-3.06 ± 0.03; 0.04 ± 0.05-1.96 ± 0.03 and 0.62 ± 0.01-120.52 ± 0.10 μg g(-1) for lead, nickel and aluminum ions, respectively. The concentrations of basic TEs iron, copper, manganese and zinc were determined as 3.87 ± 0.04-16.76 ± 0.06; 0.45 ± 0.03-2.15 ± 0.01; 0.13 ± 0.01-15.02 ± 0.14 and 0.80 ± 0.09-12.03 ± 0.19 for honey samples. Also, toxic metal, lead, nickel and aluminum values in the honey samples were determined as 1.21 ± 0.12-2.46 ± 0.21; 0.28 ± 0.14-0.88 ± 0.43 and 2.11 ± 0.02-8.04 ± 0.08. A comparison between gathered data and literature values has performed and it is determined that such findings are suitable with the literature.

Lead-free precussion primer mixes based on metastable interstitial composite (MIC) technology

DOEpatents

Dixon, George P.; Martin, Joe A.; Thompson, Don

1998-01-01

A lead-free percussion primer composition and a percussion cup containing e composition. The lead-free percussion primer composition is comprised of a mixture of about 45 wt % aluminum powder having an outer coating of aluminum oxide and molybdenum trioxide powder or a mixture of about 50 wt % aluminum powder having an outer coating of aluminum oxide and polytetrafluoroethylene powder. The aluminum powder, molybdenum trioxide powder and polytetrafluoroethylene powder has a particle size of 0.1 .mu.m or less, more preferably a particle size of from about 200-500 angstroms.

Copper, lead and zinc concentrations of human breast milk as affected by maternal dietary practices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umoren, J.; Kies, C.

1986-03-01

Maternal dietary practices have been found to affect the concentrations of some nutrients in human breast milk. Lead toxicity is a concern in young children. Lead, copper and zinc are thought to compete for intestinal absorption sites. The objective of the current project was to compare copper, lead and zinc contents of breast milk from practicing lacto-vegetarian and omnivore, lactating women at approximately four months post-partum. Analyses were done by atomic absorption spectrophotometry using a carbon rod attachment. Copper concentrations were higher in milk samples from lacto-ovo-vegetarians. Milk samples from the omnivores had the highest lead and zinc concentrations. Leadmore » and copper concentrations in milk were negatively correlated. The higher zinc concentrations in the milk of the omnivore women may have been related to better utilization of zinc from meat than from plant food sources.« less

Environmental pollution levels of lead and zinc in Ishiagu and Uburu communities of Ebonyi State, Nigeria.

PubMed

Oje, Obinna A; Uzoegwu, Peter N; Onwurah, Ikechukwu N E; Nwodo, Uchechukwu U

2010-09-01

Water and soil samples from the area were therefore analyzed for their lead and zinc content. Computation of pollution statuses of lead and zinc revealed topsoil lead geoaccumulation indices of -0.143 and -0.069 and zinc geoaccumulation indices of 1.168 and 0.713 for Ishiagu and Uburu respectively. The pollution indices were determined to be 0.499 and 0.3564 for soil in Ishiagu and Uburu respectively and also 5.11 and 2.42 for water in Ishiagu and Uburu communities respectively. Water/soil concentration ratio were found to be 0.0018 and 0.0014 for lead in Ishiagu and Uburu respectively. On the other hand, the water/soil concentration ratio for zinc was computed to be 0.001 and 0.0008 for Ishiagu and Uburu respectively. These results seem to suggest that the pollution of the environment by these heavy metals in the areas were as a result of the water being contaminated by lead and zinc not necessarily their concentrations in the soil.

CESIUM RECOVERY FROM AQUEOUS SOLUTIONS

DOEpatents

Goodall, C.A.

1960-09-13

A process is given for precipitating cesium on zinc ferricyanide (at least 0.0004 M) from aqueous solutions containing mineral acid in a concentration of from 0.2 N acidity to 0.61 N acid-deficiency and advantageously, but not necessarily, also aluminum nitrate in a concentration of from l to 2.5 M.

Water-quality assessment of the upper Illinois River Basin in Illinois, Indiana, and Wisconsin; major and trace elements in water, sediment, and biota, 1978-90

USGS Publications Warehouse

Fitzpatrick, F.A.; Scudder, B.C.; Crawford, J.K.; Schmidt, A.R.; Sieverling, J.B.

1995-01-01

The distribution of 22 major and trace elements was examined in water, sediment, and biota in the upper Illinois River Basin in Illinois, Indiana, and Wisconsin as part of a pilot National Water-Quality Assessment project done by the U.S. Geological Survey from 1987 through 1990. The 22 elements are aluminum, antimony, arsenic, barium, beryllium, boron, cadmium, chromium, cobalt, copper, iron, lead, manganese, mercury, molybdenum, nickel, phosphorus, selenium, silver, strontium, vanadium, and zinc. Concentrations of U.S. Environmental Protection Agency (USEPA) priority pollutants among the 22 elements were elevated in the Chicago area in all three aquatic components (water, sediment, and biota). Further, some of the priority pollutants also were found at elevated concentrations in biota in agricultural areas in the basin. Cadmium, chromium, copper, iron, lead, mercury, silver, and zinc concentrations in water exceeded USEPA acute or chronic water-quality criteria at several sites in the Chicago area. Correlations among concentra- tions of elements in water, sediment, and biota were found, but the correlation analysis was hindered by the large proportion of observations less than the minimum reporting level in water. Those sites where water-quality criteria were sometimes exceeded were not always the same sites where concentrations in biota were the largest. This relation indicates that accumulation of these pollutants in biota is confounded by complex geochemical and biological processes that differ throughout the upper Illinois River Basin.

Long-term sorption of metals is similar among plastic types: implications for plastic debris in aquatic environments.

PubMed

Rochman, Chelsea M; Hentschel, Brian T; Teh, Swee J

2014-01-01

Concerns regarding plastic debris and its ability to accumulate large concentrations of priority pollutants in the aquatic environment led us to quantify relationships between different types of mass-produced plastic and metals in seawater. At three locations in San Diego Bay, we measured the accumulation of nine targeted metals (aluminum, chromium, manganese, iron, cobalt, nickel, zinc, cadmium and lead) sampling at 1, 3, 6, 9 and 12 months, to five plastic types: polyethylene terephthalate (PET), high-density polyethylene (HDPE), polyvinyl chloride (PVC), low-density polyethylene (LDPE), and polypropylene (PP). Accumulation patterns were not consistent over space and time, and in general all types of plastic tended to accumulate similar concentrations of metals. When we did observe significant differences among concentrations of metals at a single sampling period or location in San Diego Bay, we found that HDPE typically accumulated lesser concentrations of metals than the other four polymers. Furthermore, over the 12-month study period, concentrations of all metals increased over time, and chromium, manganese, cobalt, nickel, zinc and lead did not reach saturation on at least one plastic type during the entire 12-month exposure. This suggests that plastic debris may accumulate greater concentrations of metals the longer it remains at sea. Overall, our work shows that a complex mixture of metals, including those listed as priority pollutants by the US EPA (Cd, Ni, Zn and Pb), can be found on plastic debris composed of various plastic types.

Long-Term Sorption of Metals Is Similar among Plastic Types: Implications for Plastic Debris in Aquatic Environments

PubMed Central

Rochman, Chelsea M.; Hentschel, Brian T.; Teh, Swee J.

2014-01-01

Concerns regarding plastic debris and its ability to accumulate large concentrations of priority pollutants in the aquatic environment led us to quantify relationships between different types of mass-produced plastic and metals in seawater. At three locations in San Diego Bay, we measured the accumulation of nine targeted metals (aluminum, chromium, manganese, iron, cobalt, nickel, zinc, cadmium and lead) sampling at 1, 3, 6, 9 and 12 months, to five plastic types: polyethylene terephthalate (PET), high-density polyethylene (HDPE), polyvinyl chloride (PVC), low-density polyethylene (LDPE), and polypropylene (PP). Accumulation patterns were not consistent over space and time, and in general all types of plastic tended to accumulate similar concentrations of metals. When we did observe significant differences among concentrations of metals at a single sampling period or location in San Diego Bay, we found that HDPE typically accumulated lesser concentrations of metals than the other four polymers. Furthermore, over the 12-month study period, concentrations of all metals increased over time, and chromium, manganese, cobalt, nickel, zinc and lead did not reach saturation on at least one plastic type during the entire 12-month exposure. This suggests that plastic debris may accumulate greater concentrations of metals the longer it remains at sea. Overall, our work shows that a complex mixture of metals, including those listed as priority pollutants by the US EPA (Cd, Ni, Zn and Pb), can be found on plastic debris composed of various plastic types. PMID:24454866

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

40 CFR 421.75 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace Slag Granulation. PSES Pollutant or... blast furance lead bullion produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag... (pounds per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2...

40 CFR 421.75 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Lead .000 .000 Zinc .000 .000 (c) Subpart G—Blast Furnace Slag Granulation. PSES Pollutant or... blast furance lead bullion produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag... (pounds per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2...

Structural and thermomechanical properties of the zinc-blende AlX (X = P, As, Sb) compounds

NASA Astrophysics Data System (ADS)

Ha, Vu Thi Thanh; Hung, Vu Van; Hanh, Pham Thi Minh; Nguyen, Viet Tuyen; Hieu, Ho Khac

2017-08-01

The structural and thermomechanical properties of zinc-blende aluminum class of III-V compounds have been studied based on the statistical moment method (SMM) in quantum statistical mechanics. Within the SMM scheme, we derived the analytical expressions of the nearest-neighbor distance, thermal expansion coefficient, atomic mean-square displacement and elastic moduli (Young’s modulus, bulk modulus and shear modulus). Numerical calculations have been performed for zinc-blende AlX (X = As, P, Sb) at ambient conditions up to the temperature of 1000 K. Our results are in good and reasonable agreements with earlier measurements and can provide useful references for future experimental and theoretical works. This research presents a systematic approach to investigate the thermodynamic and mechanical properties of materials.

Material morphology and electrical resistivity differences in EPDM rubbers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Nancy Y. C.; Domeier, Linda A.

2008-03-01

Electrical resistance anomalies noted in EPDM gaskets have been attributed to zinc-enriched surface sublayers, about 10-{micro}m thick, in the sulfur cured rubber material. Gasket over-compression provided the necessary connector pin contact and was also found to cause surprising morphological changes on the gasket surfaces. These included distributions of zinc oxide whiskers in high pressure gasket areas and cone-shaped features rich in zinc, oxygen, and sulfur primarily in low pressure protruding gasket areas. Such whiskers and cones were only found on the pin side of the gaskets in contact with a molded plastic surface and not on the back side inmore » contact with an aluminum surface. The mechanisms by which such features are formed have not yet been defined.« less

Low Temperature Film Growth of the Oxides of Zinc, Aluminum, and Vanadium (and Related Systems, Oxides of Gold and Germanium, Nitrides of Aluminum and Tungsten) by Reactive Sputter Deposition.

DTIC Science & Technology

1988-02-01

the optical behavior of the material in its preswitched, or A Perkin-Elmer Model 330 UV - Visible -IR double beam ,% spectrophotometer with a specular...S ~ * ." at.* U a * . a. *%~ ~9g 0 ~ --- a.. ’ a * ~ .r~vaa- *a,~ * ~ * ~****.,*a,* *** UV - Visible -IR Optical Behavior of Sputter Deposited Gee x...Films deposited in 0 to 60% Ar were nominally germania. However, transmission in the UV - visible , the strength of the 245nm defect center, the optical

Space thermal control development

NASA Technical Reports Server (NTRS)

Hoover, M. J.; Grodzka, P. G.; Oneill, M. J.

1971-01-01

The results of experimental investigations on a number of various phase change materials (PCMs) and PCMs in combination with metals and other materials are reported. The evaluations include the following PCM system performance characteristics: PCM and PCM/filler thermal diffusivities, the effects of long-term thermal cycling, PCM-container compatibility, and catalyst effectiveness and stability. Three PCMs demonstrated performance acceptable enough to be considered for use in prototype aluminum thermal control devices. These three PCMs are lithium nitrate trihydrate with zinc hydroxy nitrate catalyst, acetamide, and myristic acid. Of the fillers tested, aluminum honeycomb filler was found to offer the most increase in system thermal diffusivity.

Fabrication and RF characterization of zinc oxide based Film Bulk Acoustic Resonator

NASA Astrophysics Data System (ADS)

Patel, Raju; Bansal, Deepak; Agrawal, Vimal Kumar; Rangra, Kamaljit; Boolchandani, Dharmendar

2018-06-01

This work reports fabrication and characterization of Film Bulk Acoustic Resonator (FBAR) to improve the performance characteristics for RF filter and sensing application. Zinc oxide as a piezoelectric (PZE) material was deposited on an aluminum bottom electrode using an RF magnetron sputtering, at room temperature, and gold as top electrode for the resonator. Tetramethyl ammonium hydroxide (TMAH) setup was used for bulk silicon etching to make back side cavity to confine the acoustic signals. The transmission characteristics show that the FBARs have a central frequency at 1.77 GHz with a return loss of -10.7 dB.

Development of an environmentally benign anticorrosion coating for aluminum alloy using green pigments and organofunctional silanes

NASA Astrophysics Data System (ADS)

Yin, Zhangzhang

Aerospace aluminum alloys such as Al alloy 2024-T3 and 7075-T6 are subject to localized corrosion due the existence of intermetallics containing Cu, Mg or Zn. Current protection measurement employs substantial use of chromate and high VOC organics, both of which are identified as environment and health hazards. The approach of this study is to utilize a combination of organofunctional silanes and a compatible inhibitor integrated into high-performance waterborne resins. First, an extensive pigment screening has been done to find replacements for chromates using the testing methodology for fast corrosion inhibition evaluation and pigment. Zinc phosphate and calcium zinc phosphomolybdate were found to have the best overall performance on Al alloys. Some new corrosion inhibitors were synthesized by chemical methods or modified by plasma polymerization for use in the coatings. Low-VOC, chromate-free primers (superprimer) were developed using these pigments with silane and acrylic-epoxy resins. The developed superprimer demonstrated good corrosion inhibition on aluminum substrates. The functions of inhibitor and silane in the coating were investigated. Both silane and inhibitor are critical for the performance of the superprimer. Silane was found to improve the adhesion of the coating to the substrate and also facilitate corrosion prevention. Addition of zinc phosphate to the coating improved the resistance of a scratched area against corrosion. The microstructure of the acrylic-epoxy superprimer coating was studied. SEM/EDAX revealed that the superprimer has a self-assembled stratified double-layer structure which accounts for the strong anti-corrosion performance of the zinc phosphate pigment. Zinc phosphate leaches out from the coating to actively protect the scratched area. The leaching of pigment was confirmed in the ICP-MS analysis and the leaching rate was measured. Coating-metal interface and the scribe of coated panels subjected to corrosion test was studied. ToF-SIMS studies confirmed the presence of silane at the interface and the hydrolysis of the silane. The abundant presence of silane was believed to improve the adhesion and also facilitate the corrosion prevention. The protection mechanism of the acrylic-epoxy superprimer was proposed. The self-assembled double-layer structure of the acrylic-epoxy superprimer consist of a less-penetrable hydrophobic layer (epoxy-dominated) on the top and a hydrophilic layer (acrylic-dominated) accommodating the inhibitors underneath. This unique structure of the acrylic-epoxy accounts for the good protection of the coating. Furthermore, the inhibition mechanism of zinc phosphate was explored and compared to those which have been reported. Based on the protection mechanism of the superprimer, electrodeposition was explored in order to achieve a more organized coating with a better engineered metal/coating interface. The electrodeposited coatings were found to have higher barrier property and anticorrosion performance.

An evaluation of airborne nickel, zinc, and lead exposure at hot dip galvanizing plants.

PubMed

Verma, D K; Shaw, D S

1991-12-01

Industrial hygiene surveys were conducted at three hot dip galvanizing plants to determine occupational exposure to nickel, zinc, and lead. All three plants employed the "dry process" and used 2% nickel, by weight, in their zinc baths. A total of 32 personal and area air samples were taken. The air samples were analyzed for nickel, zinc, and lead. Some samples were also analyzed for various species of nickel (i.e., metallic, soluble, and oxidic). The airborne concentrations observed for nickel and its three species, zinc, and lead at the three plants were all well below the current and proposed threshold limit values recommended by the American Conference of Governmental Industrial Hygienists (ACGIH).

All-Aluminum Thin Film Transistor Fabrication at Room Temperature.

PubMed

Yao, Rihui; Zheng, Zeke; Zeng, Yong; Liu, Xianzhe; Ning, Honglong; Hu, Shiben; Tao, Ruiqiang; Chen, Jianqiu; Cai, Wei; Xu, Miao; Wang, Lei; Lan, Linfeng; Peng, Junbiao

2017-02-23

Bottom-gate all-aluminum thin film transistors with multi conductor/insulator nanometer heterojunction were investigated in this article. Alumina (Al₂O₃) insulating layer was deposited on the surface of aluminum doping zinc oxide (AZO) conductive layer, as one AZO/Al₂O₃ heterojunction unit. The measurements of transmittance electronic microscopy (TEM) and X-ray reflectivity (XRR) revealed the smooth interfaces between ~2.2-nm-thick Al₂O₃ layers and ~2.7-nm-thick AZO layers. The devices were entirely composited by aluminiferous materials, that is, their gate and source/drain electrodes were respectively fabricated by aluminum neodymium alloy (Al:Nd) and pure Al, with Al₂O₃/AZO multilayered channel and AlO x :Nd gate dielectric layer. As a result, the all-aluminum TFT with two Al₂O₃/AZO heterojunction units exhibited a mobility of 2.47 cm²/V·s and an I on / I off ratio of 10⁶. All processes were carried out at room temperature, which created new possibilities for green displays industry by allowing for the devices fabricated on plastic-like substrates or papers, mainly using no toxic/rare materials.

Galvanic coupling between D6AC steel, 6061-T6 aluminum, Inconel 718 and graphite-epoxy composite material: Corrosion occurrence and prevention

NASA Technical Reports Server (NTRS)

Danford, M. D.; Higgins, R. H.

1983-01-01

The effects of galvanic coupling between D6AC steel, 6061-T6 aluminum, Inconel 718, and graphite-epoxy composite material (G/E) in 3.5% NaCl were studied. Measurements of corrosion potentials, galvanic currents and corrosion rates of the bare metals using weight-loss methods served to establish the need for corrosion protection in cases where D6AC steel and 6061-T6 aluminum are galvanically coupled to G/E in salt water while Inconel 718 was shown to be compatible with G/E. Six tests were made to study corrosion protective methods for eliminating galvanic corrosion in the cases of D6AC steel and 6061-T6 aluminum coupled to G/E. These results indicate that, when the G/E is completely coated with paint or a paint/polyurethane resin combination, satisfactory protection of the D6AC steel is achieved with either a coat of zinc-rich primer or a primer/topcoat combination. Likewise, satisfactory corrosion protection of the aluminum is achieved by coating it with an epoxy coating system.

25 CFR 215.5 - Royalty rates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES... gross proceeds of all lead and zinc ores and concentrates extracted from the leased premises, the... royalty shall not be less than the highest and best obtainable market price of the lead and zinc ores and...

25 CFR 215.5 - Royalty rates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES... gross proceeds of all lead and zinc ores and concentrates extracted from the leased premises, the... royalty shall not be less than the highest and best obtainable market price of the lead and zinc ores and...

Lead and zinc dust depositions from ore trains characterised using lead isotopic compositions.

PubMed

Kristensen, L J; Taylor, M P; Morrison, A L

2015-03-01

This study investigates an unusual source of environmental lead contamination - the emission and deposition of lead and zinc concentrates along train lines into and out of Australia's oldest silver-lead-zinc mine at Broken Hill, Australia. Transport of lead and zinc ore concentrates from the Broken Hill mines has occurred for more than 125 years, during which time the majority was moved in uncovered rail wagons. A significant amount of ore was lost to the adjoining environments, resulting in soil immediately adjacent to train lines elevated with concentrations of lead (695 mg kg(-1)) and zinc (2230 mg kg(-1)). Concentrations of lead and zinc decreased away from the train line and also with depth shown in soil profiles. Lead isotopic compositions demonstrated the soil lead contained Broken Hill ore in increasing percentages closer to the train line, with up to 97% apportioned to the mined Broken Hill ore body. SEM examination showed ceiling dusts collected from houses along the train line were composed of unweathered galena particles, characteristic of the concentrate transported in the rail wagons. The loss of ore from the uncovered wagons has significantly extended the environmental footprint of contamination from local mining operations over an area extending hundreds of kilometres along each of the three train lines.

40 CFR 421.136 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b) Subpart M—Blast... Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as N) .000 .000 (c... .000 Arsenic .000 .000 Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (d) Subpart M—Lead Paste...

40 CFR 421.136 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b) Subpart M—Blast... Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as N) .000 .000 (c... .000 Arsenic .000 .000 Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (d) Subpart M—Lead Paste...

40 CFR 421.136 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b) Subpart M—Blast... Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as N) .000 .000 (c... .000 Arsenic .000 .000 Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (d) Subpart M—Lead Paste...

40 CFR 421.136 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b) Subpart M—Blast... Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as N) .000 .000 (c... .000 Arsenic .000 .000 Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (d) Subpart M—Lead Paste...

40 CFR 421.136 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b) Subpart M—Blast... Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as N) .000 .000 (c... .000 Arsenic .000 .000 Lead .000 .000 Zinc .000 .000 Ammonia (as N) .000 .000 (d) Subpart M—Lead Paste...

25 CFR 215.21 - Payment of gross production tax on lead and zinc.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Payment of gross production tax on lead and zinc. 215.21 Section 215.21 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.21 Payment of gross production tax on lead and...

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag Granulation. BAT Effluent... per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2,418... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent...

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Lead .000 .000 Zinc .000 .000 (d) Subpart G—Dross Reverberatory Slag Granulation. BAT Effluent... per billion pounds) of slag, speiss, or matte granulated Lead 1,612.000 748.400 Zinc 5,872.000 2,418... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent...

Z dependence of thick-target β-ray backscattering

NASA Astrophysics Data System (ADS)

Sharma, K. K.; Singh, M.

1980-04-01

Variation of β-ray backscattering with the atomic number of target material has been studied using thick targets of polythene, aluminum, iron, copper, zinc, tin, silver, tungsten, and lead for five β emitters, viz., 35S, 147Pm, 204Tl, 32P, and 90Sr-90Y. Effects of geometry and β-ray end-point energy have been investigated using a reflection geometry in which the geometry factors were varied by more than 40 and β-ray energy varied over a range 0.167-2.27 MeV. It is found that the mean value of the index of Z dependence of β-ray backscattering is 1.840.05 over these regions of geometry and energy. Deviations for soft β emitters have been confirmed as due to air absorption. The importance of these results in studies of two-component systems is emphasized.

LEVELING METAL COATINGS

DOEpatents

Gage, H.A.

1959-02-10

A method is described for applying metallic coatings to a cylinder of uranium. An aluminum-silicon coat is applied by a process consisting of first cleaning the article by immersion for 5 minutes in 50% nitric acid at 65 C. The article then is dipped through a flux, prepared by adding 10% sodium fluoride to 90% of a flux comprising 53% potassium chloride, 42% lithium chloride, and 5% sodium chloride at 560 for 2 minutes and then directly into a molten metal bath comprising 99% aluminun and 12% silicon at 620 C for 3 minutes. While the coating is yet molten the article is transferred to a pair of steel rollers and rolled until the coating solidifies. By varying the composition of the flux other metals such as zinc, lead or the like may be coated on uranium in a similar manner.

Role of nutritional zinc in the prevention of osteoporosis.

PubMed

Yamaguchi, Masayoshi

2010-05-01

Zinc is known as an essential nutritional factor in the growth of the human and animals. Bone growth retardation is a common finding in various conditions associated with dietary zinc deficiency. Bone zinc content has been shown to decrease in aging, skeletal unloading, and postmenopausal conditions, suggesting its role in bone disorder. Zinc has been demonstrated to have a stimulatory effect on osteoblastic bone formation and mineralization; the metal directly activates aminoacyl-tRNA synthetase, a rate-limiting enzyme at translational process of protein synthesis, in the cells, and it stimulates cellular protein synthesis. Zinc has been shown to stimulate gene expression of the transcription factors runt-related transcription factor 2 (Runx2) that is related to differentiation into osteoblastic cells. Moreover, zinc has been shown to inhibit osteoclastic bone resorption due to inhibiting osteoclast-like cell formation from bone marrow cells and stimulating apoptotic cell death of mature osteoclasts. Zinc has a suppressive effect on the receptor activator of nuclear factor (NF)-kappaB ligand (RANKL)-induced osteoclastogenesis. Zinc transporter has been shown to express in osteoblastic and osteoclastic cells. Zinc protein is involved in transcription. The intake of dietary zinc causes an increase in bone mass. beta-Alanyl-L: -histidinato zinc (AHZ) is a zinc compound, in which zinc is chelated to beta-alanyl-L: -histidine. The stimulatory effect of AHZ on bone formation is more intensive than that of zinc sulfate. Zinc acexamate has also been shown to have a potent-anabolic effect on bone. The oral administration of AHZ or zinc acexamate has the restorative effect on bone loss under various pathophysiologic conditions including aging, skeletal unloading, aluminum bone toxicity, calcium- and vitamin D-deficiency, adjuvant arthritis, estrogen deficiency, diabetes, and fracture healing. Zinc compounds may be designed as new supplementation factor in the prevention and therapy of osteoporosis.

Zinc-mediated Allosteric Inhibition of Caspase-6*

PubMed Central

Velázquez-Delgado, Elih M.; Hardy, Jeanne A.

2012-01-01

Zinc and caspase-6 have independently been implicated in several neurodegenerative disorders. Depletion of zinc intracellularly leads to apoptosis by an unknown mechanism. Zinc inhibits cysteine proteases, including the apoptotic caspases, leading to the hypothesis that zinc-mediated inhibition of caspase-6 might contribute to its regulation in a neurodegenerative context. Using inductively coupled plasma optical emission spectroscopy, we observed that caspase-6 binds one zinc per monomer, under the same conditions where the zinc leads to complete loss of enzymatic activity. To understand the molecular details of zinc binding and inhibition, we performed an anomalous diffraction experiment above the zinc edge. The anomalous difference maps showed strong 5σ peaks, indicating the presence of one zinc/monomer bound at an exosite distal from the active site. Zinc was not observed bound to the active site. The zinc in the exosite was liganded by Lys-36, Glu-244, and His-287 with a water molecule serving as the fourth ligand, forming a distorted tetrahedral ligation sphere. This exosite appears to be unique to caspase-6, as the residues involved in zinc binding were not conserved across the caspase family. Our data suggest that binding of zinc at the exosite is the primary route of inhibition, potentially locking caspase-6 into the inactive helical conformation. PMID:22891250

25 CFR 215.10 - Renewal of leases on developed lands.

Code of Federal Regulations, 2011 CFR

2011-04-01

....10 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC... where the lands have heretofore been leased, and lead and zinc ores have been discovered hereon, and it..., or to parties who have expended capital in lead and zinc mining operation and development of the land...

Accumulation of metals in fish from lead-zinc mining areas of southeastern Missouri, USA

USGS Publications Warehouse

Schmitt, Christopher J.; Brumbaugh, William G.; May, Thomas W.

2007-01-01

The potential effects of proposed lead-zinc mining in an ecologically sensitive area were assessed by studying a nearby mining district that has been exploited for about 30 yr under contemporary environmental regulations and with modern technology. Blood and liver samples representing fish of three species (largescale stoneroller, Campostoma oligolepis, n=91; longear sunfish, Lepomis megalotis, n=105; and northern hog sucker, Hypentelium nigricans, n=20) were collected from 16 sites representing a range of conditions relative to lead-zinc mining and ore beneficiation in southeastern Missouri. Samples were analyzed for lead, zinc, and cadmium, and for a suite of biomarkers (reported in a companion paper). A subset of the hog sucker (n=9) representing three sites were also analyzed for nickel and cobalt. Blood and liver lead concentrations were highly correlated (r=0.84-0.85, P < 0.01) in all three species and were significantly (ANOVA, P < 0.01) greater at sites < 10 km downstream of active lead-zinc mines and mills and in a historical lead-zinc mining area than at reference sites, including a site in the area proposed for new mining. Correlations between blood and liver cadmium concentrations were less evident than for lead but were nevertheless statistically significant (r=0.26-0.69, P < 0.01-0.07). Although blood and liver cadmium concentrations were highest in all three species at sites near mines, within-site variability was greater and mining-related trends were less evident than for lead. Blood and liver zinc concentrations were significantly correlated only in stoneroller (r=0.46, P < 0.01) and mining-related trends were not evident. Concentrations of cobalt and nickel in blood and liver were significantly higher (ANOVA, P < 0.01) at a site near an active mine than at a reference site and a site in the historical lead-zinc mining area. These findings confirm previous studies indicating that lead and other metals are released to streams from active lead-zinc mines and are available for uptake by aquatic organisms. ?? 2006 Elsevier Inc. All rights reserved.

Accumulation of metals in fish from lead-zinc mining areas of southeastern Missouri, USA.

PubMed

Schmitt, Christopher J; Brumbaugh, William G; May, Thomas W

2007-05-01

The potential effects of proposed lead-zinc mining in an ecologically sensitive area were assessed by studying a nearby mining district that has been exploited for about 30 yr under contemporary environmental regulations and with modern technology. Blood and liver samples representing fish of three species (largescale stoneroller, Campostoma oligolepis, n=91; longear sunfish, Lepomis megalotis, n=105; and northern hog sucker, Hypentelium nigricans, n=20) were collected from 16 sites representing a range of conditions relative to lead-zinc mining and ore beneficiation in southeastern Missouri. Samples were analyzed for lead, zinc, and cadmium, and for a suite of biomarkers (reported in a companion paper). A subset of the hog sucker (n=9) representing three sites were also analyzed for nickel and cobalt. Blood and liver lead concentrations were highly correlated (r=0.84-0.85, P<0.01) in all three species and were significantly (ANOVA, P<0.01) greater at sites <10 km downstream of active lead-zinc mines and mills and in a historical lead-zinc mining area than at reference sites, including a site in the area proposed for new mining. Correlations between blood and liver cadmium concentrations were less evident than for lead but were nevertheless statistically significant (r=0.26-0.69, P <0.01-0.07). Although blood and liver cadmium concentrations were highest in all three species at sites near mines, within-site variability was greater and mining-related trends were less evident than for lead. Blood and liver zinc concentrations were significantly correlated only in stoneroller (r=0.46, P<0.01) and mining-related trends were not evident. Concentrations of cobalt and nickel in blood and liver were significantly higher (ANOVA, P<0.01) at a site near an active mine than at a reference site and a site in the historical lead-zinc mining area. These findings confirm previous studies indicating that lead and other metals are released to streams from active lead-zinc mines and are available for uptake by aquatic organisms.

Effect of Precursors on Key Opto-electrical Properties of Successive Ion Layer Adsorption and Reaction-Prepared Al:ZnO Thin Films

NASA Astrophysics Data System (ADS)

Kumar, K. Deva Arun; Valanarasu, S.; Ganesh, V.; Shkir, Mohd.; Kathalingam, A.; AlFaify, S.

2018-02-01

Aluminum-doped zinc oxide (Al:ZnO) thin films were deposited on glass substrates by successive ion layer adsorption and reaction (SILAR) method using different precursors. This inexpensive SILAR method involves dipping of substrate sequentially in zinc solution, de-ionized water and ethylene glycol in multiple cycles. Prepared films were investigated by x-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscope (AFM), optical absorption, photoluminescence (PL), Raman spectroscopy and electrical studies. XRD study confirmed incorporation of aluminum in ZnO lattice with a polycrystalline hexagonal wurtzite structure of the films. The crystallite size determined by the Scherrer equation showed an increase from 28 nm to 35 nm for samples S1 to S4, respectively. SEM study showed smooth morphology with homogeneous distribution of particles. From the AFM images, the surface roughness was found to change according to precursors. For the optical analysis, the zinc chloride precursor showed high optical transmittance of about 90% in the visible range with a band gap value 3.15 eV. The room-temperature PL spectra exhibited a stronger violet emission peak at 420 nm for all the prepared samples. The Raman spectra showed a peak around 435 cm-1 which could be assigned to non-polar optical phonons (E2-high) mode AZO films of a ZnO wurtzite structure. Hall effect measurements showed n-type conductivity with low resistivity ( ρ) and high carrier concentrations ( n) of 2.39 × 10-3 Ω-cm and 8.96 × 1020 cm-3, respectively, for the film deposited using zinc chloride as precursor. The above properties make the prepared AZO film to be regarded as a very promising electrode material for fabrication of optoelectronic devices.

New CVD-based method for the growth of high-quality crystalline zinc oxide layers

NASA Astrophysics Data System (ADS)

Huber, Florian; Madel, Manfred; Reiser, Anton; Bauer, Sebastian; Thonke, Klaus

2016-07-01

High-quality zinc oxide (ZnO) layers were grown using a new chemical vapour deposition (CVD)-based low-cost growth method. The process is characterized by total simplicity, high growth rates, and cheap, less hazardous precursors. To produce elementary zinc vapour, methane (CH4) is used to reduce a ZnO powder. By re-oxidizing the zinc with pure oxygen, highly crystalline ZnO layers were grown on gallium nitride (GaN) layers and on sapphire substrates with an aluminum nitride (AlN) nucleation layer. Using simple CH4 as precursor has the big advantage of good controllability and the avoidance of highly toxic gases like nitrogen oxides. In photoluminescence (PL) measurements the samples show a strong near-band-edge emission and a sharp line width at 5 K. The good crystal quality has been confirmed in high resolution X-ray diffraction (HRXRD) measurements. This new growth method has great potential for industrial large-scale production of high-quality single crystal ZnO layers.

Geochemical characterization of shallow ground water in the Eutaw aquifer, Montgomery, Alabama

USGS Publications Warehouse

Robinson, J.L.; Journey, C.A.

2004-01-01

Ground water samples were collected from 30 wells located in, or directly down gradient from, recharge areas of the Eutaw aquifer in Montgomery, Alabama. The major ion content of the water evolves from calcium-sodium-chloride- dominated type in the recharge area to calcium-bicarbonate-dominated type in the confined portion of the aquifer. Ground water in the recharge area was undersaturated with respect to aluminosilicate and carbonate minerals. Ground water in the confined portion of the aquifer was at equilibrium levels for calcite and potassium feldspar. Dissolved oxygen and nitrite-plus-nitrate concentrations decreased as ground water age increased; pH, iron, and sulfate concentrations increased as ground water age increased. Aluminum, copper, and zinc concentrations decreased as ground water age and pH increased. These relations indicate that nitrate, aluminum, copper, and zinc are removed from solution as water moves from recharge areas to the confined areas of the Eutaw aquifer. The natural evolution of ground water quality, which typically increases the pH and decreases the dissolved oxygen content, may be an important limiting factor to the migration of nitrogen based compounds and metals.

Optical properties of aluminum-doped zinc oxide films deposited by direct-current pulse magnetron reactive sputtering

NASA Astrophysics Data System (ADS)

Gao, Xiao-Yong; Chen, Chao; Zhang, Sa

2014-03-01

A series of <103>-oriented aluminum-doped zinc oxide (AZO) films were deposited on glass substrates via direct-current pulse magnetron reactive sputtering at different O2-to-Ar gas flow ratios (GFRs). The optical properties of the films were characterized using the fitted optical constants in the general oscillator model (which contains two Psemi-Tri oscillators) through the use of measured ellipsometric parameters. The refractive index dispersion data below the interband absorption edge were analyzed using a single-oscillator model. The fitted optical energy gap obtained using the single-oscillator model clearly shows a blue shift, followed by a red shift, as the GFR increases from 0.9/18 to 2.1/18. This shift can be attributed to the change in the free electron concentration of the film, which is closely related to the film stress. In addition, the fitted β value indicates that the AZO film falls under the ionic class. The photoluminescence spectrum indicates a photoluminescence mechanism of the direct and wide energy gap semiconductor.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sweet, William J.; Oldham, Christopher J.; Parsons, Gregory N., E-mail: parsons@ncsu.edu

Flexible electronics and wearable technology represent a novel and growing market for next generation devices. In this work, the authors deposit conductive zinc oxide films by atomic layer deposition onto nylon-6 nonwoven fiber mats and spun-cast films, and quantify the impact that deposition temperature, coating thickness, and aluminum doping have on the conductivity of the coated substrates. The authors produce aluminum doped zinc oxide (AZO) coated fibers with conductivity of 230 S/cm, which is ∼6× more conductive than ZnO coated fibers. Furthermore, the authors demonstrate AZO coated fibers maintain 62% of their conductivity after being bent around a 3 mm radius cylinder.more » As an example application, the authors fabricate an “all-fiber” pressure sensor using AZO coated nylon-6 electrodes. The sensor signal scales exponentially under small applied force (<50 g/cm{sup 2}), yielding a ∼10{sup 6}× current change under 200 g/cm{sup 2}. This lightweight, flexible, and breathable touch/force sensor could function, for example, as an electronically active nonwoven for personal or engineered system analysis and diagnostics.« less

25 CFR 215.10 - Renewal of leases on developed lands.

Code of Federal Regulations, 2010 CFR

2010-04-01

... rights on said land to be offered for sale at public auction to the highest bidder. If the lead and zinc....10 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC... where the lands have heretofore been leased, and lead and zinc ores have been discovered hereon, and it...

Investigation of the role of α-lipoic acid on fatty acids profile, some minerals (zinc, copper, iron) and antioxidant activity against aluminum-induced oxidative stress in the liver of male rats.

PubMed

Sahin, Zafer; Ozkaya, Ahmet; Yilmaz, Okkes; Yuce, Abdurrauf; Gunes, Mehmet

2017-07-26

We have investigated the effects of α-lipoic acid (LA), a powerful antioxidant, on the fatty acid (FA) profiles, aluminum accumulation, antioxidant activity and some minerals such as zinc, copper and iron against aluminum chloride (AlCl3)-induced oxidative stress in rat liver. Twenty-eight male Wistar rats were divided into four groups as control, LA, AlCl3 and LA+AlCl3. For 30 days, LA was intraperitoneally administrated (50 mg/kg) and AlCl3 was given via orogastric gavage (1600 ppm) every other day. AlCl3-treated animals exhibited higher hepatic malondialdehyde concentration and lower glutathione peroxidase and catalase activity, whereas these alterations were restored by the LA supplementation. Total saturated FA of the AlCl3-treated group was higher than the LA supplementation groups. Moreover, total unsaturated FA level of the LA+AlCl3 group was higher than the AlCl3-treated group. Hepatic zinc level of the AlCl3-treated group was lower than the control group, whereas it was higher in the LA and the LA+AlCl3 groups. Hepatic copper levels did not significantly change in the experimental groups. Iron level was lower in the LA and LA+AlCl3 groups compared with the AlCl3-treated group. Moreover, the liver Al concentration was found to be lower in the LA and LA+AlCl3 groups compared to the AlCl3 group. These results indicate that AlCl3 treatment can induce oxidative stress in the liver. LA supplementation has a beneficial effect on the AlCl3-induced alterations such as high lipid peroxidation, Al accumulation, FA profile ratios and mineral concentrations.

Release of iron, zinc, and lead from common iron construction bars and zinc metallic bars in water solutions and meals.

PubMed

Lechtig, Aarón; Lòpez de Romaña, Daniel; Boy, Erick; Vargas, Alejandro; Rosas del Portal, Mauricio; Huaylinos, María Luisa

2007-12-01

The use of iron pots has decreased the prevalence of anemia. To investigate the release of iron, zinc, and lead from metallic iron and zinc bars incubated in water and in meals. Iron, zinc, and lead concentrations were measured at different incubation conditions in water and in meals. The iron concentration in water was 1.26 mg/L after incubation with one iron bar at pH 7 and 100 degrees C for 20 minutes and in meals was 0.97 mg per 100 g of wet meals, rich in phytate, cooking at 100 degrees C during 20 minutes. The maximum contents were 7720 mg/L of iron and 1826 mg/L of zinc in vinegar at pH 3 and 20 degrees C after 90 and 32 days, respectively. Lead was released from the bars, but at concentrations well below the upper tolerable limits. In outreach populations, the use of iron and zinc metallic bars in water and meals could contribute to sustainable, very low-cost prevention of iron and zinc deficiencies, and home-fortified vinegar could be used for treatment of both deficiencies. Field trials should be performed to determine the impact that the use of iron and zinc metallic bars in water and meals might have on the iron and zinc status of population groups.

Intraurban Variation of Fine Particle Elemental Concentrations in New York City.

PubMed

Ito, Kazuhiko; Johnson, Sarah; Kheirbek, Iyad; Clougherty, Jane; Pezeshki, Grant; Ross, Zev; Eisl, Holger; Matte, Thomas D

2016-07-19

Few past studies have collected and analyzed within-city variation of fine particulate matter (PM2.5) elements. We developed land-use regression (LUR) models to characterize spatial variation of 15 PM2.5 elements collected at 150 street-level locations in New York City during December 2008-November 2009: aluminum, bromine, calcium, copper, iron, potassium, manganese, sodium, nickel, lead, sulfur, silicon, titanium, vanadium, and zinc. Summer- and winter-only data available at 99 locations in the subsequent 3 years, up to November 2012, were analyzed to examine variation of LUR results across years. Spatial variation of each element was modeled in LUR including six major emission indicators: boilers burning residual oil; traffic density; industrial structures; construction/demolition (these four indicators in buffers of 50 to 1000 m), commercial cooking based on a dispersion model; and ship traffic based on inverse distance to navigation path weighted by associated port berth volume. All the elements except sodium were associated with at least one source, with R(2) ranging from 0.2 to 0.8. Strong source-element associations, persistent across years, were found for residual oil burning (nickel, zinc), near-road traffic (copper, iron, and titanium), and ship traffic (vanadium). These emission source indicators were also significant and consistent predictors of PM2.5 concentrations across years.

Aluminum concentration and substrate temperature in chemical sprayed ZnO:Al thin solid films

NASA Astrophysics Data System (ADS)

Lozada, Erick Velázquez; Castañeda, L.; Aguilar, E. Austria

2018-02-01

The continuous interest in the synthesis and properties study of materials has permitted the development of semiconductor oxides. Zinc oxide (ZnO) with hexagonal wurzite structure is a wide band gap n-type semiconductor and interesting material over a wide range. Chemically sprayed aluminium-doped zinc oxide thin films (ZnO:Al) were deposited on soda-lime glass substrates starting from zinc pentanedionate and aluminium pentanedionate. The influence of both the dopant concentration in the starting solution and the substrate temperature on the composition, morphology, and transport properties of the ZnO:Al thin films were studied. The structure of all the ZnO:Al thin films was polycrystalline, and variation in the preferential growth with the aluminium content in the solution was observed: from an initial (002) growth in films with low Al content, switching to a predominance of (101) planes for heavily dopant regime. The crystallite size was found to decrease with doping concentration and range from 33 to 20 nm. First-order Raman scattering from ZnO:Al, all having the wurtzite structure. The assignments of the E2 mode in ZnO:Al differ from previous investigations. The film composition and the dopant concentration were determined by Auger Electron Spectroscopy (AES); these results showed that the films are almost stoichiometric ZnO. The optimum deposition conditions leading to conductive and transparent ZnO:Al thin films were also found. In this way a resistivity of 0.03 Ω-cm with a (002) preferential growth, were obtained in optimized ZnO:Al thin films.

Atomic layer deposition of Al-incorporated Zn(O,S) thin films with tunable electrical properties

NASA Astrophysics Data System (ADS)

Park, Helen Hejin; Jayaraman, Ashwin; Heasley, Rachel; Yang, Chuanxi; Hartle, Lauren; Mankad, Ravin; Haight, Richard; Mitzi, David B.; Gunawan, Oki; Gordon, Roy G.

2014-11-01

Zinc oxysulfide, Zn(O,S), films grown by atomic layer deposition were incorporated with aluminum to adjust the carrier concentration. The electron carrier concentration increased up to one order of magnitude from 1019 to 1020 cm-3 with aluminum incorporation and sulfur content in the range of 0 ≤ S/(Zn+Al) ≤ 0.16. However, the carrier concentration decreased by five orders of magnitude from 1019 to 1014 cm-3 for S/(Zn+Al) = 0.34 and decreased even further when S/(Zn+Al) > 0.34. Such tunable electrical properties are potentially useful for graded buffer layers in thin-film photovoltaic applications.

The Ballistic and Corrosion Evaluation of Magnesium Elektron E675 vs. Baseline Magnesium Alloy AZ31B and Aluminum Alloy 5083 for Armor Applications

DTIC Science & Technology

2011-06-01

critical property in reducing the plastic failure of the material. The ductility is marginally better than Mg AZ31B. 2 Table 1. Chemical...composition (%) of metal alloys. Element (%)/Alloy CPMg 9980B AZ31B-H24 AA5083-H131 Aluminum — 2.5–3.5 REM Manganese 0.10 max 0.2–1.0 0.40‒1.0 Zinc — 0.6...This trend was attributed to the lack of ductility in E675 compared to 5083, which reduced energy dissipation. Visual analysis of the Mg E675

Percentage of different aluminum doping influence the morphological and optical properties of ZnO nanostructured growth for sensor application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, R., E-mail: ruziana12@gmail.com; NANO-SciTech Centre, Institue of Science, Universiti Teknologi MARA, 40450 Shah Alam, Selangor; Faculty of Applied Sciences, Universiti Teknologi MARA Pahang, 26400 Bandar Tun Razak Jengka, Pahang

In this work, Zinc Oxide (ZnO) with different aluminum (Al) doping percentage was synthesis by sol gel immersion method. Al doped ZnO at various doping percentage from 1, 2, 3, 4 and 5. It was found that with different Al percentage influence the morphological and optical properties of ZnO growth. Field Emission Scanning Electron Microscope (FESEM) image showed the use of different Al doping causes the difference in geometry and size of ZnO nanorods growth. Based on UV-Vis spectroscopy, the transmittance at 1% Al doping has the highest spectrum.

Development of Scintillators in Nuclear Medicine.

PubMed

Khoshakhlagh, Mohammad; Islamian, Jalil Pirayesh; Abedi, Seyed Mohammad; Mahmoudian, Babak

2015-01-01

High-quality image is necessary for accurate diagnosis in nuclear medicine. There are many factors in creating a good image and detector is the most important one. In recent years, several detectors are studied to get a better picture. The aim of this paper is comparison of some type of these detectors such as thallium activated sodium iodide bismuth germinate cesium activated yttrium aluminum garnet (YAG: Ce) YAP: Ce "lutetium aluminum garnet activated by cerium" CRY018 "CRY019" lanthanum bromide and cadmium zinc telluride. We studied different properties of these crystals including density, energy resolution and decay times that are more important factors affecting the image quality.

Development of Scintillators in Nuclear Medicine

PubMed Central

Khoshakhlagh, Mohammad; Islamian, Jalil Pirayesh; Abedi, Seyed Mohammad; Mahmoudian, Babak

2015-01-01

High-quality image is necessary for accurate diagnosis in nuclear medicine. There are many factors in creating a good image and detector is the most important one. In recent years, several detectors are studied to get a better picture. The aim of this paper is comparison of some type of these detectors such as thallium activated sodium iodide bismuth germinate cesium activated yttrium aluminum garnet (YAG: Ce) YAP: Ce “lutetium aluminum garnet activated by cerium” CRY018 “CRY019” lanthanum bromide and cadmium zinc telluride. We studied different properties of these crystals including density, energy resolution and decay times that are more important factors affecting the image quality. PMID:26420984

METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

DOEpatents

Lemon, L.C.

1960-05-24

Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

SOLDERING OF ALUMINUM BASE METALS

DOEpatents

Erickson, G.F.

1958-02-25

This patent deals with the soldering of aluminum to metals of different types, such as copper, brass, and iron. This is accomplished by heating the aluminum metal to be soldered to slightly above 30 deg C, rubbing a small amount of metallic gallium into the part of the surface to be soldered, whereby an aluminum--gallium alloy forms on the surface, and then heating the aluminum piece to the melting point of lead--tin soft solder, applying lead--tin soft solder to this alloyed surface, and combining the aluminum with the other metal to which it is to be soldered.

Low zinc serum levels and high blood lead levels among school-age children in coastal area

NASA Astrophysics Data System (ADS)

Pramono, Adriyan; Panunggal, Binar; Rahfiludin, M. Zen; Swastawati, Fronthea

2017-02-01

The coverage of environmental lead toxicant was quiet wide. Lead exposure recently has been expected to be associated with zinc deficiency and blood indices disturbance. Emphasizing on children, which could absorb more than 50 % of lead that enters the body. Lead became the issue on the coastal area due to it has polluted the environment and waters as the source of fisheries products. This was a cross sectional study to determined nutritional status, blood lead levels, zinc serum levels, blood indices levels, fish intake among school children in coastal region of Semarang. This study was carried out on the school children aged between 8 and 12 years old in coastal region of Semarang. Nutritional status was figured out using anthropometry measurement. Blood lead and zinc serum levels were analyzed using the Atomic Absorbent Spectrophotometry (AAS) at a wavelength of 213.9 nm for zinc serum and 283.3 nm for blood lead. Blood indices was measured using auto blood hematology analyzer. Fish intake was assessed using 3-non consecutive days 24-hours food recall. The children had high lead levels (median 34.86 μg/dl, range 11.46 - 58.86 μg/dl) compared to WHO cut off. Zinc serum levels was low (median 18.10 μg/dl, range 10.25 - 41.39 μg/dl) compared to the Joint WHO/UNICEF/IAEA/IZiNCG cut off. Approximately 26.4% of children were anemic. This study concluded that all school children had high blood lead levels, low zinc serum, and presented microcytic hypochromic anemia. This phenomenon should be considered as public health concern.

40 CFR 421.135 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... produced Antimony 1.299 .579 Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b... produced from smelting Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as... refining Antimony .087 .039 Arsenic .063 .026 Lead .013 .006 Zinc .046 .019 Ammonia (as N) .000 .000 (d...

40 CFR 421.135 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... produced Antimony 1.299 .579 Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b... produced from smelting Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as... refining Antimony .087 .039 Arsenic .063 .026 Lead .013 .006 Zinc .046 .019 Ammonia (as N) .000 .000 (d...

40 CFR 421.135 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... produced Antimony 1.299 .579 Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b... produced from smelting Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as... refining Antimony .087 .039 Arsenic .063 .026 Lead .013 .006 Zinc .046 .019 Ammonia (as N) .000 .000 (d...

40 CFR 421.135 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... produced Antimony 1.299 .579 Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b... produced from smelting Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as... refining Antimony .087 .039 Arsenic .063 .026 Lead .013 .006 Zinc .046 .019 Ammonia (as N) .000 .000 (d...

40 CFR 421.135 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... produced Antimony 1.299 .579 Arsenic .936 .384 Lead .189 .087 Zinc .687 .283 Ammonia (as N) .000 .000 (b... produced from smelting Antimony 5.038 2.245 Arsenic 3.628 1.488 Lead .731 .339 Zinc 2.662 1.096 Ammonia (as... refining Antimony .087 .039 Arsenic .063 .026 Lead .013 .006 Zinc .046 .019 Ammonia (as N) .000 .000 (d...

40 CFR 421.113 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .174 .081 Zinc... monthly average mg/Kg (pounds per million pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .069 .032 Zinc...

40 CFR 421.113 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .174 .081 Zinc... monthly average mg/Kg (pounds per million pounds) of concentrate digested Lead 2.592 1.203 Zinc 9.442 3... Maximum for monthly average mg/kg (pounds per million pounds) of concentrate digested Lead .069 .032 Zinc...

Gallium

USGS Publications Warehouse

Foley, Nora K.; Jaskula, Brian W.; Kimball, Bryn E.; Schulte, Ruth F.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Gallium is a soft, silvery metallic element with an atomic number of 31 and the chemical symbol Ga. Gallium is used in a wide variety of products that have microelectronic components containing either gallium arsenide (GaAs) or gallium nitride (GaN). GaAs is able to change electricity directly into laser light and is used in the manufacture of optoelectronic devices (laser diodes, light-emitting diodes [LEDs], photo detectors, and solar cells), which are important for aerospace and telecommunications applications and industrial and medical equipment. GaAs is also used in the production of highly specialized integrated circuits, semiconductors, and transistors; these are necessary for defense applications and high-performance computers. For example, cell phones with advanced personal computer-like functionality (smartphones) use GaAs-rich semiconductor components. GaN is used principally in the manufacture of LEDs and laser diodes, power electronics, and radio-frequency electronics. Because GaN power transistors operate at higher voltages and with a higher power density than GaAs devices, the uses for advanced GaN-based products are expected to increase in the future. Gallium technologies also have large power-handling capabilities and are used for cable television transmission, commercial wireless infrastructure, power electronics, and satellites. Gallium is also used for such familiar applications as screen backlighting for computer notebooks, flat-screen televisions, and desktop computer monitors.Gallium is dispersed in small amounts in many minerals and rocks where it substitutes for elements of similar size and charge, such as aluminum and zinc. For example, gallium is found in small amounts (about 50 parts per million) in such aluminum-bearing minerals as diaspore-boehmite and gibbsite, which form bauxite deposits, and in the zinc-sulfide mineral sphalerite, which is found in many mineral deposits. At the present time, gallium metal is derived mainly as a byproduct of the processing of bauxite ore for aluminum; lesser amounts of gallium metal are produced from the processing of sphalerite ore from three types of deposits (sediment-hosted, Mississippi Valley-type, and volcanogenic massive sulfide) for zinc. The United States is expected to meet its current and expected future needs for gallium through imports of primary, recycled, and refined gallium, as well as through domestic production of recycled and refined gallium. The U.S. Geological Survey estimates that world resources of gallium in bauxite exceed 1 billion kilograms, and a considerable quantity of gallium could be present in world zinc reserves.

Relative toxicity of lead and five proposed substitute shot types to pen-reared mallards

USGS Publications Warehouse

Grandy, John W.; Locke, Louis N.; Bagley, George E.

1968-01-01

A 30-day toxicity test was made to determine the relative toxicity of lead, a tin-lead alloy, zinc, nickel, teflon-coated steel, and tin, all in shot form, to pen-reared mallard drakes. All of the 15 ducks dosed with lead died. Twenty-seven percent of 15 dosed with alloy, and 20 percent of 15 dosed with zinc also died. Ten of the remaining zinc-dosed ducks showed signs of distress, including losses of muscular control and body weight. There were no deaths among 15 ducks dosed with nickel, 15 dosed with teflon-coated steel, and 15 dosed with tin. Seventy-three percent of those dosed with nickel shot eliminated all shot before the end of the 30-day period. Acid-fast intranuclear inclusion bodies were present in the kidneys of mallards dosed with commercial lead shot, or with tin-lead alloy shot, but not in the kidneys of birds given nickel, tin, or teflon-coated steel shot. Atypical, pale, acid-fast bodies were found in kidneys of 1 of 15 birds dosed with zinc. An iron-containing pigment, which stained positive with the Prussian blue technique, was present in variable amounts in almost all livers. Zinc-dosed ducks that died or were killed while still showing signs of zinc intoxication had higher iron levels in the liver than ducks that had recovered from zinc intoxication.

Cratering Equations for Zinc Orthotitanate Coated Aluminum

NASA Technical Reports Server (NTRS)

Hyde, James; Christiansen, Eric; Liou, Jer-Chyi; Ryan, Shannon

2009-01-01

The final STS-125 servicing mission (SM4) to the Hubble Space Telescope (HST) in May of 2009 saw the return of the 2nd Wide Field Planetary Camera (WFPC2) aboard the shuttle Discovery. This hardware had been in service on HST since it was installed during the SM1 mission in December of 1993 yielding one of the longest low Earth orbit exposure times (15.4 years) of any returned space hardware. The WFPC2 is equipped with a 0.8 x 2.2 m radiator for thermal control of the camera electronics (Figure 1). The space facing surface of the 4.1 mm thick aluminum radiator is coated with Z93 zinc orthotitanate thermal control paint with a nominal thickness of 0.1 0.2 mm. Post flight inspections of the radiator panel revealed hundreds of micrometeoroid/orbital debris (MMOD) impact craters ranging in size from less than 300 to nearly 1000 microns in diameter. The Z93 paint exhibited large spall areas around the larger impact sites (Figure 2) and the craters observed in the 6061-T651 aluminum had a different shape than those observed in uncoated aluminum. Typical hypervelocity impact craters in aluminum have raised lips around the impact site. The craters in the HST radiator panel had suppressed crater lips, and in some cases multiple craters were present instead of a single individual crater. Humes and Kinard observed similar behavior after the WFPC1 post flight inspection and assumed the Z93 coating was acting like a bumper in a Whipple shield. Similar paint behavior (spall) was also observed by Bland2 during post flight inspection of the International Space Station (ISS) S-Band Antenna Structural Assembly (SASA) in 2008. The SASA, with similar Z93 coated aluminum, was inspected after nearly 4 years of exposure on the ISS. The multi-crater phenomena could be a function of the density, composition, or impact obliquity angle of the impacting particle. For instance, a micrometeoroid particle consisting of loosely bound grains of material could be responsible for creating the multiple craters. Samples were obtained from the HST largest craters for examination by electron microscope equipped with x-ray spectrometers to determine impactor source (micrometeoroid or orbital debris). In an attempt to estimate the MMOD particle diameters that produced these craters, this paper will present equations for spall diameter, crater depth and crater diameter in Z93 coated aluminum. The equations will be based on hypervelocity impact tests of Z93 painted aluminum at the NASA White Sands Test Facility. Equations inputs for velocities beyond the testable regime are expected from hydrocode simulations of Z93 coated aluminum using CTH and ANSYS AUTODYN.

Low-Frequency Noise in Amorphous Indium Zinc Oxide Thin Film Transistors with Aluminum Oxide Gate Insulator

NASA Astrophysics Data System (ADS)

Chen, Ya-Yi; Liu, Yuan; Wu, Zhao-Hui; Wang, Li; Li, Bin; En, Yun-Fei; Chen, Yi-Qiang

2018-04-01

Not Available Supported by the National Natural Science Foundation of China under Grant No 61574048, the Science and Technology Research Project of Guangdong Province under Grant Nos 2015B090912002 and 2015B090901048, and the Pearl River S&T Nova Program of Guangzhou under Grant No 201710010172.

40 CFR 467.63 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... achievable. 467.63 Section 467.63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Subcategory § 467.63 Effluent limitations representing the degree of effluent reduction attainable by the... Zinc 2.98 1.24 Aluminum 13.10 6.52 Subpart F Cleaning or Etching Bath Pollutant or pollutant property...

40 CFR 467.53 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... achievable. 467.53 Section 467.53 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... § 467.53 Effluent limitations representing the degree of effluent reduction attainable by the....367 Cyanide 0.591 0.245 Zinc 2.974 1.243 Aluminum 13.10 6.519 Subpart E Cleaning or Etching Bath...

40 CFR 467.23 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... achievable. 467.23 Section 467.23 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... § 467.23 Effluent limitations representing the degree of effluent reduction attainable by the... 0.59 0.25 Zinc 2.98 1.25 Aluminum 13.10 6.52 Subpart B Cleaning or Etching Bath Pollutant or...

Compatibility of Anti-Wear Additives with Non-Ferrous Engine Bearing Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qu, Jun; Zhou, Yan

Investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected non-ferrous engine bearing alloys, specifically aluminum and bronze alloys that are commonly used in connecting rod end journal bearings and bushings, to gain fundamental understanding to guide future development of engine lubricants

76 FR 76945 - Pure Magnesium From the People's Republic of China: Final Results of the 2009-2010 Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-09

... used in making its preliminary determination of the surrogate value for truck freight as well as the... combination, 1.5% or more, by weight, of the following alloying elements: Aluminum, manganese, zinc, silicon... based our determination of the surrogate financial ratios on the financial statements of Hindalco...

Stabilization of lead (Pb) and zinc (Zn) in contaminated rice paddy soil using starfish: A preliminary study.

PubMed

Moon, Deok Hyun; Hwang, Inseong; Koutsospyros, Agamemnon; Cheong, Kyung Hoon; Ok, Yong Sik; Ji, Won Hyun; Park, Jeong-Hun

2018-05-01

Lead (Pb) and zinc (Zn) contaminated rice paddy soil was stabilized using natural (NSF) and calcined starfish (CSF). Contaminated soil was treated with NSF in the range of 0-10 wt% and CSF in the range of 0-5 wt% and cured for 28 days. Toxicity characteristic leaching procedure (TCLP) test was used to evaluate effectiveness of starfish treatment. Scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) analyses were conducted to investigate the mechanism responsible for effective immobilization of Pb and Zn. Experimental results suggest that NSF and CSF treatments effectively immobilize Pb and Zn in treated rice paddy soil. TCLP levels for Pb and Zn were reduced with increasing NSF and CSF dosage. Comparison of the two treatment methods reveals that CSF treatment is more effective than NSF treatment. Leachability of the two metals is reduced approximately 58% for Pb and 51% for Zn, upon 10 wt% NSF treatment. More pronounced leachability reductions, 93% for Pb and 76% for Zn, are achieved upon treatment with 5 wt% CSF. Sequential extraction results reveal that NSF and CSF treatments of contaminated soil generated decrease in exchangeable/weak acid Pb and Zn soluble fractions, and increase of residual Pb and Zn fractions. Results for the SEM-EDX sample treated with 5 wt% CSF indicate that effective Pb and Zn immobilization is most probably associated with calcium silicate hydrates (CSHs) and calcium aluminum hydrates (CAHs). Copyright © 2018 Elsevier Ltd. All rights reserved.

Alert to users of calcium supplements as antihypertensive agents due to trace metal contaminants.

PubMed

Boulos, F M; von Smolinski, A

1988-07-01

Although there are controversies in the role of calcium as an antihypertensive agent, the use of "health food" supplements, such as dolomite and bone meal, is on the rise especially among the older population. One brand of commercial dolomite tablets were investigated for metallic contents such as aluminum (Al), arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), lead (Pb), manganese (Mn), sclemium (Se), and zinc (Zn). Ten randomly selected tablets were weighted, dried, pulverized and low-temperature plasma ashed. An ash aliquot of each tablet was dissolved in 35% Ultrex nitric acid, and after dilution analyzed using a Perkin-Elmer Model 5000 atomic absorption spectrophotometer equipped with an HGA-500 graphite furnace, As-1 autosampler, and PRS-10 printer sequencer. The results (presented as mean wt/g of powder +/- 95% confidence limits) are: Al 900 +/- 300 micrograms/g; As 1.3 +/- 0.3 micrograms/g; Cd 0.16 +/- 0.04 micrograms/g; Cr 5.9 +/- 1.4 micrograms/g; Cu 3.0 +/- 0.6 micrograms/g; Pb 1.9 +/- 0.5 micrograms/g; Mn 66 +/- 7.0 micrograms/g; Se 1.6 +/- 0.4 micrograms/g; and Zn 147 +/- 88 micrograms/g. These trace metals could pose health hazards to the public such as lead poisoning, dementia, and hypertension due to cadmium. Also, zinc can potentiate cadmium-hypertensive effects. The need exists to initiate some regulations to limit maximal content of trace metals in "health food" supplements to protect high-risk groups and that sector of the population who use megadoses of such products.

All-Aluminum Thin Film Transistor Fabrication at Room Temperature

PubMed Central

Yao, Rihui; Zheng, Zeke; Zeng, Yong; Liu, Xianzhe; Ning, Honglong; Hu, Shiben; Tao, Ruiqiang; Chen, Jianqiu; Cai, Wei; Xu, Miao; Wang, Lei; Lan, Linfeng; Peng, Junbiao

2017-01-01

Bottom-gate all-aluminum thin film transistors with multi conductor/insulator nanometer heterojunction were investigated in this article. Alumina (Al2O3) insulating layer was deposited on the surface of aluminum doping zinc oxide (AZO) conductive layer, as one AZO/Al2O3 heterojunction unit. The measurements of transmittance electronic microscopy (TEM) and X-ray reflectivity (XRR) revealed the smooth interfaces between ~2.2-nm-thick Al2O3 layers and ~2.7-nm-thick AZO layers. The devices were entirely composited by aluminiferous materials, that is, their gate and source/drain electrodes were respectively fabricated by aluminum neodymium alloy (Al:Nd) and pure Al, with Al2O3/AZO multilayered channel and AlOx:Nd gate dielectric layer. As a result, the all-aluminum TFT with two Al2O3/AZO heterojunction units exhibited a mobility of 2.47 cm2/V·s and an Ion/Ioff ratio of 106. All processes were carried out at room temperature, which created new possibilities for green displays industry by allowing for the devices fabricated on plastic-like substrates or papers, mainly using no toxic/rare materials. PMID:28772579

Analytical results and sample locality map of heavy-mineral-concentrate and rock samples from the Castle Peaks Wilderness Study Area (CDCA- 266), San Bernardino County, California

USGS Publications Warehouse

Adrian, B.M.; Frisken, J.G.; Malcolm, M.J.; Crock, J.G.

1986-01-01

The report presents water-quality and geohydrologic information for 106 public water-supply wells in Illinois. These wells were sampled during April to December 1984 as part of a pilot program to develop a ground-water observation network in the State. The pilot program was designed to sample single-aquifer wells from three major aquifer systems--(1) sand and gravel, both confined and unconfined; (2) Silurian dolomite; and (3) the Ironton-Galesville deep sandstone. Data are tabulated for water temperature, pH, specific conductance, oxidation-reduction potential, ammonia nitrogen, nitrate + nitrite nitrogen, phosphorus, silica, arsenic, lead, mercury, fluoride, chloride, sulfate, cyanide, phenols, selenium, residue on evaporation at 180 degrees Celsius, alkalinity, calcium, magnesium, sodium, potassium, barium, boron, beryllium, cadmium, chormium, copper, cobalt, iron, aluminum, manganese, nickel, silver, strontium, vanadium, zinc, and selected geohydrologic information.

Whole-body concentrations of elements in three fish species from offshore oil platforms and natural areas in the Southern California Bight, USA

USGS Publications Warehouse

Love, Milton S.; Saiki, Michael K.; May, Thomas W.; Yee, Julie L.

2013-01-01

elements. Forty-two elements were excluded from statistical comparisons as they (1) consisted of major cations that were unlikely to accumulate to potentially toxic concentrations; (2) were not detected by the analytical procedures; or (3) were detected at concentrations too low to yield reliable quantitative measurements. The remaining 21 elements consisted of aluminum, arsenic, barium, cadmium, chromium, cobalt, copper, gallium, iron, lead, lithium, manganese, mercury, nickel, rubidium, selenium, strontium, tin, titanium, vanadium, and zinc. Statistical comparisons of these elements indicated that none consistently exhibited higher concentrations at oil platforms than at natural areas. However, the concentrations of copper, selenium, titanium, and vanadium in Pacific sanddab were unusual because small individuals exhibited either no differences between oil platforms and natural areas or significantly lower concentrations at oil platforms than at natural areas, whereas large individuals exhibited significantly higher concentrations at oil platforms than at natural areas.

Honeybees and honey as monitors for heavy metal contamination near thermal power plants in Mugla, Turkey.

PubMed

Silici, Sibel; Uluozlu, Ozgur Dogan; Tuzen, Mustafa; Soylak, Mustafa

2016-03-01

In the present work, 6 honeydew samples of known geographical and botanical origins and 11 honeybee samples were analyzed to detect possible contamination by the thermoelectric power plants in Mugla, Turkey. The contents of trace elements were determined by atomic absorption spectrometry after application of microwave digestion. The samples from the thermal power plants, which were 10-22 km away from the hives, that did not cause pollution in honeydew honeys were also analyzed. The levels of copper, cadmium (Cd), lead (Pb), zinc, manganese, iron, chromium, nickel, and aluminum were similar to the values found in other recent studies in literature. However, it was found that the contamination levels of the toxic elements such as Pb and Cd in honeybee samples measured relatively higher than that of honey samples. The study concludes that honeybees may be better bioindicators of heavy metal pollution than honey. © The Author(s) 2013.

Chemical characterization of individual particles (PM10) from ambient air in Guiyang City, China.

PubMed

Xie, R K; Seip, H M; Leinum, J R; Winje, T; Xiao, J S

2005-05-01

PM10 samples were collected during 5 days in Guiyang, China in July 2003. A total of about 2300 particles was analyzed by an automated Scanning Electron Microscope with Energy-Dispersive Spectrometer (SEM-EDS). Hierarchical cluster analysis (HCA) was used to identify different particle types that occurred in the aerosol. Seventeen particle types were identified and presented in the order of decreasing number abundance as: silicomanganese slag, soil and fly ash, coal burning, silicomanganese, quartz, syngenite, S-bearing iron, calcium rich, gypsum, sphalerite, dolomite, iron, alloy, lead sulfate, zinc rich, sulfur-rich particles and aluminum manufacturing dust. The majority of the particles in the studied size range are of anthropogenic origin, especially from metallurgical industry. The study illustrates the complexity of particle pollution in air of an industrial Chinese city and the results should be useful in planning mitigation measures.

Geochemistry of Red Mountain Creek, Colorado, under low-flow conditions, August 2002

USGS Publications Warehouse

Runkel, Robert L.; Kimball, Briant A.; Walton-Day, Katherine; Verplanck, Philip L.

2005-01-01

Red Mountain Creek, an acid mine drainage stream in southwestern Colorado, was the subject of a synoptic study conducted in August 2002. During the synoptic study, a solution containing lithium chloride was injected continuously to allow for the calculation of streamflow using the tracer-dilution method. Synoptic water-quality samples were collected from 48 stream sites and 29 inflow locations along a 5.4-kilometer study reach. Data from the study provide profiles of pH, concentration, and mass load with a high degree of spatial resolution. Despite the presence of 10 circumneutral inflows, pH remained below 3.4 at all stream sites. Concentration profiles indicate that dissolved concentrations of aluminum, cadmium, copper, lead, and zinc exceed chronic aquatic-life standards established by the State of Colorado along the entire study reach. Comparison of total recoverable and dissolved concentrations suggests that most constituents were transported conservatively. Exceptions to this pattern include arsenic, iron, molybdenum, and vanadium, four constituents that were subject to precipitation and(or) sorption reactions as the addition of a circumneutral tributary resulted in a slight increase in instream pH. Evaluation of data from the 29 inflow locations indicates a sharp contrast between the east and west sides of the watershed; inflows from the east side have high constituent concentrations and acidic pH, whereas inflows from the west side have lower concentrations and generally higher pH. Loading profiles, the product of streamflow and concentration, are used to rank potential sources of metals and acidity within the watershed. Four sources account for 83, 72, 70, 69, 64, and 61 percent of the aluminum, iron, arsenic, zinc, copper, and cadmium loading within the study reach, respectively. All four sources appear to be the result of surface inflows that have been affected by mining activities. The relatively small number of major sources and the fact that they are attributable to surface inflows are two factors that may facilitate effective remediation.

Arsenite binding-induced zinc loss from PARP-1 is equivalent to zinc deficiency in reducing PARP-1 activity, leading to inhibition of DNA repair

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xi; Zhou, Xixi; Du, Libo

2014-01-15

Inhibition of DNA repair is a recognized mechanism for arsenic enhancement of ultraviolet radiation-induced DNA damage and carcinogenesis. Poly(ADP-ribose) polymerase-1 (PARP-1), a zinc finger DNA repair protein, has been identified as a sensitive molecular target for arsenic. The zinc finger domains of PARP-1 protein function as a critical structure in DNA recognition and binding. Since cellular poly(ADP-ribosyl)ation capacity has been positively correlated with zinc status in cells, we hypothesize that arsenite binding-induced zinc loss from PARP-1 is equivalent to zinc deficiency in reducing PARP-1 activity, leading to inhibition of DNA repair. To test this hypothesis, we compared the effects ofmore » arsenite exposure with zinc deficiency, created by using the membrane-permeable zinc chelator TPEN, on 8-OHdG formation, PARP-1 activity and zinc binding to PARP-1 in HaCat cells. Our results show that arsenite exposure and zinc deficiency had similar effects on PARP-1 protein, whereas supplemental zinc reversed these effects. To investigate the molecular mechanism of zinc loss induced by arsenite, ICP-AES, near UV spectroscopy, fluorescence, and circular dichroism spectroscopy were utilized to examine arsenite binding and occupation of a peptide representing the first zinc finger of PARP-1. We found that arsenite binding as well as zinc loss altered the conformation of zinc finger structure which functionally leads to PARP-1 inhibition. These findings suggest that arsenite binding to PARP-1 protein created similar adverse biological effects as zinc deficiency, which establishes the molecular mechanism for zinc supplementation as a potentially effective treatment to reverse the detrimental outcomes of arsenic exposure. - Highlights: • Arsenite binding is equivalent to zinc deficiency in reducing PARP-1 function. • Zinc reverses arsenic inhibition of PARP-1 activity and enhancement of DNA damage. • Arsenite binding and zinc loss alter the conformation of zinc finger structure.« less

Behavior of lead and zinc in plasma, erythrocytes, and urine and ALAD in erythrocytes following intravenous infusion of CaEDTA in lead workers.

PubMed

Araki, S; Aono, H; Fukahori, M; Tabuki, K

1984-01-01

To evaluate the effect of calcium disodium ethylenediamine tetraacetate (CaEDTA) on concentrations of lead and zinc in plasma, erythrocytes, whole blood, and urine, we administered CaEDTA by intravenous infusion for 1 hr to seven lead workers with blood lead concentrations of 46-67 micrograms/100 g (mean 54 micrograms/100 g). The plasma lead concentration (PPb) and the mobilization yield of lead in urine by CaEDTA were highest during the period between 1 and 2 hr after the infusion was started. In contrast, the lead concentration in erythrocytes (EPb) and in whole blood (BPb) remained unchanged during the 24 hr following infusion. Plasma zinc concentration (PZn) also fell rapidly following CaEDTA infusion; the decline was followed by a gradual rise in the zinc concentration in erythrocytes (EZn) without alteration in the zinc in whole blood. The mobilization yield of zinc in urine by CaEDTA (MZn) reached its highest level within 1 hr after the start of the infusion. Delta-aminolevulinic acid dehydratase (ALAD) activity in erythrocytes gradually increased for 5 hr following CaEDTA infusion. These observations suggest that (1) PPb concentration is a more sensitive indicator of the body burden of chelatable lead than is either BPb or EPb; (2) MZn is mobilized mostly from plasma during the first several hours following the start of CaEDTA infusion, and the fall in PZn concentration following infusion is compensated first by a rise in EZn concentration and then by an immediate redistribution of zinc in other organs to the blood; and (3) Pb-inhibited ALAD activity is reactivated by the increased EZn during and shortly after CaEDTA infusion.

Influence of thickness of zinc coating on CMT welding-brazing with AlSi5 alloy wire

NASA Astrophysics Data System (ADS)

Jin, Pengli; Wang, Zhiping; Yang, Sinan; Jia, Peng

2018-03-01

Effect of thickness of zinc coating on Cold Mattel Transfer (CMT) brazing of aluminum and galvanized steel is investigated. The thickness of zinc coating is 10 μm, 30 μm, and 60 μm, respectively. A high-speed camera was used to capture images of welding process of different specimens; the microstructure and composition analyses of the welding seam were examined by scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS); the mechanical properties were measured in the form of Nano-indentation experiments. The results showed that arc characteristics and metal transfer behavior were unsteady at the beginning of welding process and that became stable after two cycles of CMT. With the thickness of zinc coating thickening, arc characteristics and metal transfer behaviors were more deteriorated. Compared with 10 μm and 30 μm, clad appearance of 60 μm was straight seam edges and a smooth surface which wetting angle was 60°. Zinc-rich zone at the seam edges was formed by zinc dissolution and motel pool oscillating, and zinc content of 10 μm and 30 μm were 5.8% and 7.75%. Zinc content of 60 μm was 14.61%, and it was a belt between galvanized steel and welding seam. The thickness of intermetallic compounds layer was in the range of 1-8 μm, and it changed with the thickness of zinc coating. The average hardness of the reaction layer of 60 μm is 9.197 GPa.

Geochemical variability of soils and biogeochemical variability of plants in the Piceance Basin, Colorado

USGS Publications Warehouse

Tuttle, M.L.; Severson, R.C.; Dean, W.E.; Klusman, R.W.

1986-01-01

Geochemical baselines for native soils and biogeochemical baselines for plants in the Piceance basin provide data that can be used to assess geochemical and biogeochemical effects of oil-shale development, monitor changes in the geochemical and biogeochemical environment during development, and assess the degree of success of rehabilitation of native materials after development. Baseline values for 52 properties in native soils, 15 properties in big sagebrush, and 13 properties in western wheatgrass were established. Our Study revealed statistically significant regional variations of the following properties across the basin: in soil&-aluminum, cobalt, copper, iron, manganese, sodium, nickel, phosphorus, lead, scandium, titanium, vanadium, zinc, organic and total carbon, pH, clay, dolomite, sodium feldspar, and DTPA-extractable calcium, cadmium, iron, potassium, manganese, nickel, phosphorus, yttrium, and zinc; in big sagebrush-barium, calcium, copper, magnesium, molybdenum, sodium, strontium, zinc, and ash; and in western wheatgrass-boron, barium, calcium, magnesium, manganese, molybdenum, strontium, zinc, and ash. These variations show up as north-south trends across the basin, or they reflect differences in elevation, hydrology, and soil parent material. Baseline values for properties that do not have statistically significant regional variations can be represented by geometric means and deviations calculated from all values within the basin. Chemical and mineralogical analyses of soil and chemical analyses of western wheatgrass samples from Colorado State University's experimental revegetation plot at Anvil Points provide data useful in assessing potential effects on soil and plant properties when largescale revegetation operations begin. The concentrations of certain properties are related to the presence of topsoil over spent shale in the lysimeters. In soils, calcium, fluorine, lithium, magnesium, sodium, phosphorus, strontium, carbonate and total carbon, and DTPA-extractable boron, copper, iron, magnesium, and nickel have lower concentrations in topsoil than in the spent oil shale; whereas, silicon, titanium, ytterbium, clay, quartz, and DTPA-extractable potassium have greater concentrations in the topsoil than in the spent oil shale. In western wheatgrass, molybdenum has a lower concentration in grasses growing on the topsoil than in grasses on the spent oil shale; whereas, barium, calcium, manganese, strontium, zinc, and ash have greater concentrations in grasses growing on the topsoil than on the spent oil shale. When compared to baseline values, soils in the revegetation plot are significantly higher in concentrations of lead, zinc, organic and total carbon, and DTP A-extractable cadmium, iron, manganese, nickel, phosphorus, and zinc. Whereas, western wheatgrass grown within the revegetation plot has concentrations which fall within the baseline values established in the regional study. The equations used in predicting concentrations of elements in plants from native and altered sites are cumbersome because of the large number of variables required to adequately predict expected concentrations and are of limited use because many explained only a small proportion of the total variation.

Aluminum-Silicon Alloy Having Improved Properties at Elevated Temperatures and Articles Cast Therefrom

NASA Technical Reports Server (NTRS)

Lee, Jonathan A. (Inventor); Chen, Po-Shou (Inventor)

2002-01-01

An aluminum alloy suitable for high temperature applications, such as heavy duty pistons and other internal combustion applications. having the following composition, by weight percent (wt %): Silicon: 11.0-14.0; Copper: 5.6-8.0; Iron: 0-0.8; Magnesium: 0.5-1.5; Nickel: 0.05-0.9; Manganese: 0.5-1.5; Titanium: 0.05-1.2; Zirconium: 0.12-1.2; Vanadium: 0.05-1.2; Zinc: 0.005-0.9; Strontium: 0.001-0.1; Aluminum: balance. In this alloy the ratio of silicon:magnesium is 10-25, and the ratio of copper:magnesium is 4-15. After an article is cast from this alloy, the article is treated in a solutionizing step which dissolves unwanted precipitates and reduces any segregation present in the original alloy. After this solutionizing step, the article is quenched, and is then aged at an elevated temperature for maximum strength.

Dissimilar material joining using laser (aluminum to steel using zinc-based filler wire)

NASA Astrophysics Data System (ADS)

Mathieu, Alexandre; Shabadi, Rajashekar; Deschamps, Alexis; Suery, Michel; Matteï, Simone; Grevey, Dominique; Cicala, Eugen

2007-04-01

Joining steel with aluminum involving the fusion of one or both materials is possible by laser beam welding technique. This paper describes a method, called laser braze welding, which is a suitable process to realize this structure. The main problem with thermal joining of steel/aluminum assembly with processes such as TIG or MIG is the formation of fragile intermetallic phases, which are detrimental to the mechanical performances of such joints. Braze welding permits a localized fusion of the materials resulting in a limitation on the growth of fragile phases. This article presents the results of a statistical approach for an overlap assembly configuration using a filler wire composed of 85% Zn and 15% Al. Tensile tests carried on these assemblies demonstrate a good performance of the joints. The fracture mechanisms of the joints are analyzed by a detailed characterization of the seams.

Antimycobacterial, antimicrobial, and biocompatibility properties of para-aminosalicylic acid with zinc layered hydroxide and Zn/Al layered double hydroxide nanocomposites

PubMed Central

Saifullah, Bullo; El Zowalaty, Mohamed E; Arulselvan, Palanisamy; Fakurazi, Sharida; Webster, Thomas J; Geilich, Benjamin M; Hussein, Mohd Zobir

2014-01-01

The treatment of tuberculosis by chemotherapy is complicated due to multiple drug prescriptions, long treatment duration, and adverse side effects. We report here for the first time an in vitro therapeutic effect of nanocomposites based on para-aminosalicylic acid with zinc layered hydroxide (PAS-ZLH) and zinc-aluminum layered double hydroxides (PAS-Zn/Al LDH), against mycobacteria, Gram-positive bacteria, and Gram-negative bacteria. The nanocomposites demonstrated good antimycobacterial activity and were found to be effective in killing Gram-positive and Gram-negative bacteria. A biocompatibility study revealed good biocompatibility of the PAS-ZLH nanocomposites against normal human MRC-5 lung cells. The para-aminosalicylic acid loading was quantified with high-performance liquid chromatography analysis. In summary, the present preliminary in vitro studies are highly encouraging for further in vivo studies of PAS-ZLH and PAS-Zn/Al LDH nanocomposites to treat tuberculosis. PMID:25114509

On the problem of zinc extraction from the slags of lead heat

NASA Astrophysics Data System (ADS)

Kozyrev, V. V.; Besser, A. D.; Paretskii, V. M.

2013-12-01

The possibilities of zinc extraction from the slags of lead heat are studied as applied to the ZAO Karat-TsM lead plant to be built for processing ore lead concentrates. The process of zinc extraction into commercial fumes using the technology of slag fuming by natural gas developed in Gintsvetmet is recommended for this purpose. Technological rules are developed for designing a commercial fuming plant, as applied to the conditions of the ZAO Karat-TsM plant.

Single and Combined Exposure to Zinc- and Copper-Containing Welding Fumes Lead to Asymptomatic Systemic Inflammation.

PubMed

Markert, Agnieszka; Baumann, Ralf; Gerhards, Benjamin; Gube, Monika; Kossack, Veronika; Kraus, Thomas; Brand, Peter

2016-02-01

Recently, it has been shown that exposure to welding fumes containing both zinc and copper leads to asymptomatic systemic inflammation in humans as shown by an increase of blood C-reactive protein. In the present study, it was investigated which metal is responsible for this effect. Fifteen healthy male subjects were exposed under controlled conditions to welding fumes containing either zinc, or copper, or copper and zinc. For each exposure blood C-reactive protein increased. Copper- and zinc-containing welding fumes are able to induce systemic inflammation.

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

40 CFR 464.36 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting... million pounds) of metal poured Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO...

Improved alkaline electrochemical cell

NASA Technical Reports Server (NTRS)

Fleischmann, C. W.; Oswin, H. G.; Oxley, J. E.

1970-01-01

Addition of lead ions to electrolyte suppresses zinc dendrite formation during charging cycle. A soluble lead salt can be added directly or metallic lead can be incorporated in the zinc electrode and allowed to dissolve into the electrolyte.

Lead inhibition of DNA-binding mechanism of Cys(2)His(2) zinc finger proteins.

PubMed

Hanas, J S; Rodgers, J S; Bantle, J A; Cheng, Y G

1999-11-01

The association of lead with chromatin in cells suggests that deleterious metal effects may in part be mediated through alterations in gene function. To elucidate if and how lead may alter DNA binding of cysteine-rich zinc finger proteins, lead ions were analyzed for their ability to alter the DNA binding mechanism of the Cys(2)His(2) zinc finger protein transcription factor IIIA (TFIIIA). As assayed by DNase I protection, the interaction of TFIIIA with the 50-bp internal control region of the 5S ribosomal gene was partially inhibited by 5 microM lead ions and completely inhibited by 10 to 20 microM lead ions. Preincubation of free TFIIIA with lead resulted in DNA-binding inhibition, whereas preincubation of a TFIIIA/5S RNA complex with lead did not result in DNA-binding inhibition. Because 5S RNA binds TFIIIA zinc fingers, this result is consistent with an inhibition mechanism via lead binding to zinc fingers. The complete loss of DNase I protection on the 5S gene indicates the mechanism of inhibition minimally involves the N-terminal fingers of TFIIIA. Inhibition was not readily reversible and occurred in the presence of an excess of beta-mercaptoethanol. Inhibition kinetics were fast, progressing to completion in approximately 5 min. Millimolar concentrations of sulfhydryl-specific arsenic ions were not inhibitory for TFIIIA binding. Micromolar concentrations of lead inhibited DNA binding by Sp1, another Cys(2)His(2) finger protein, but not by the nonfinger protein AP2. Inhibition of Cys(2)His(2) zinc finger transcription factors by lead ions at concentrations near those known to have deleterious physiological effects points to new molecular mechanisms for lead toxicity in promoting disease.

Zinc and lead detoxifying abilities of humic substances relevant to environmental bacterial species.

PubMed

Perelomov, L V; Sarkar, Binoy; Sizova, O I; Chilachava, K B; Shvikin, A Y; Perelomova, I V; Atroshchenko, Y M

2018-04-30

The effect of humic substances (HS) and their different fractions (humic acids (HA) and hymatomelanic acids (HMA)) on the toxicity of zinc and lead to different strains of bacteria was studied. All tested bacteria demonstrated a lower resistance to zinc than lead showing minimum inhibitory concentrations of 0.1 - 0.3mM and 0.3-0.5mM, respectively. The highest resistance to lead was characteristic of Pseudomonas chlororaphis PCL1391 and Rhodococcus RS67, while Pseudomonas chlororaphis PCL1391 showed the greatest resistance to zinc. The combined fractions of HS and HA alone reduced zinc toxicity at all added concentrations of the organic substances (50 - 200mgL -1 ) to all microorganisms, while hymatomelanic acids reduced zinc toxicity to Pseudomonas chlororaphis PCL1391 at 200mgL -1 organic concentration only. The HS fractions imparted similar effects on lead toxicity also. This study demonstrated that heavy metal toxicity to bacteria could be reduced through complexation with HS and their fractions. This was particularly true when the metal-organic complexes held a high stability, and low solubility and bioavailability. Copyright © 2018 Elsevier Inc. All rights reserved.

Characterisation of zinc delivery from a nipple shield delivery system using a breastfeeding simulation apparatus

PubMed Central

Bruggraber, Sylvaine F. A.; Gerrard, Stephen E.; Kendall, Richard A.; Tuleu, Catherine; Slater, Nigel K. H.

2017-01-01

Zinc delivery from a nipple shield delivery system (NSDS), a novel platform for administering medicines to infants during breastfeeding, was characterised using a breastfeeding simulation apparatus. In this study, human milk at flow rates and pressures physiologically representative of breastfeeding passed through the NSDS loaded with zinc-containing rapidly disintegrating tablets, resulting in release of zinc into the milk. Inductively coupled plasma optical emission spectrometry was used to detect the zinc released, using a method that does not require prior digestion of the samples and that could be applied in other zinc analysis studies in breast milk. Four different types of zinc-containing tablets with equal zinc load but varying excipient compositions were tested in the NSDS in vitro. Zinc release measured over 20 minutes ranged from 32–51% of the loaded dose. Total zinc release for sets tablets of the same composition but differing hardness were not significantly different from one another with P = 0.3598 and P = 0.1270 for two tested pairs using unpaired t tests with Welch’s correction. By the same test total zinc release from two sets of tablets having similar hardness but differing composition were also not significantly significant with P = 0.2634. Future zinc tablet composition and formulation optimisation could lead to zinc supplements and therapeutics with faster drug release, which could be administered with the NSDS during breastfeeding. The use of the NSDS to deliver zinc could then lead to treatment and prevention of some of the leading causes of child mortality, including diarrheal disease and pneumonia. PMID:28158283

Characterisation of zinc delivery from a nipple shield delivery system using a breastfeeding simulation apparatus.

PubMed

Scheuerle, Rebekah L; Bruggraber, Sylvaine F A; Gerrard, Stephen E; Kendall, Richard A; Tuleu, Catherine; Slater, Nigel K H

2017-01-01

Zinc delivery from a nipple shield delivery system (NSDS), a novel platform for administering medicines to infants during breastfeeding, was characterised using a breastfeeding simulation apparatus. In this study, human milk at flow rates and pressures physiologically representative of breastfeeding passed through the NSDS loaded with zinc-containing rapidly disintegrating tablets, resulting in release of zinc into the milk. Inductively coupled plasma optical emission spectrometry was used to detect the zinc released, using a method that does not require prior digestion of the samples and that could be applied in other zinc analysis studies in breast milk. Four different types of zinc-containing tablets with equal zinc load but varying excipient compositions were tested in the NSDS in vitro. Zinc release measured over 20 minutes ranged from 32-51% of the loaded dose. Total zinc release for sets tablets of the same composition but differing hardness were not significantly different from one another with P = 0.3598 and P = 0.1270 for two tested pairs using unpaired t tests with Welch's correction. By the same test total zinc release from two sets of tablets having similar hardness but differing composition were also not significantly significant with P = 0.2634. Future zinc tablet composition and formulation optimisation could lead to zinc supplements and therapeutics with faster drug release, which could be administered with the NSDS during breastfeeding. The use of the NSDS to deliver zinc could then lead to treatment and prevention of some of the leading causes of child mortality, including diarrheal disease and pneumonia.

Temporal and spatial variations of copper, cadmium, lead, and zinc in Ten Mile Creek in South Florida, USA.

PubMed

Yang, Yuangen; He, Zhenli; Lin, Youjian; Phlips, Edward J; Stoffella, Peter J; Powell, Charles A

2009-01-01

Lead (Pb), zinc (Zn), copper (Cu), and cadmium (Cd) often seriously deteriorate water quality. Spatial and temporal fluctuations of the metal concentrations in the Ten Mile Creek (Florida) (TMC) were monitored on a weekly basis at 7 sampling sites, from June 2005 to September 2007. River sediment samples were also collected from these sites in April, June, and October 2006 and January 2007, and analyzed for water, Mehlich 1 (M1), and Mehlich 3 (M3)-extractable metals (Mehlich, 1953, 1984), to examine the role of sediments as sources or sinks of the metals. The concentrations of lead, zinc, copper, and cadmium in the water samples were

The role of arbuscular mycorrhiza on change of heavy metal speciation in rhizosphere of maize in wastewater irrigated agriculture soil.

PubMed

Huang, Yi; Tao, Shu; Chen, You-jian

2005-01-01

To understand the roles of mycorrhiza in metal speciation in the rhizosphere and the impact on increasing host plant tolerance against excessive heavy metals in soil, maize (Zea mays L.) inoculated with arbuscular mycorrhizal fungus (Glomus mosseae) was cultivated in heavy metal contaminated soil. Speciations of copper, zinc and lead in the soil were analyzed with the technique of sequential extraction. The results showed that, in comparison to the bolked soil, the exchangeable copper increased from 26% to 43% in non-infected and AM-infected rhizoshpere respectively; while other speciation (organic, carbonate and Fe-Mn oxide copper) remained constant and the organic bound zinc and lead also increased but the exchangeable zinc and lead were undetectable. The organic bound copper, zinc and lead were higher by 15%, 40% and 20%, respectively, in the rhizosphere of arbuscular mycorrhiza infected maize in comparison to the non-infected maize. The results might indicate that mycorrhiza could protect its host plants from the phytotoxicity of excessive copper, zinc and lead by changing the speciation from bio-available to the non-bio-available form. The fact that copper and zinc accumulation in the roots and shoots of mycorrhia infected plants were significantly lower than those in the non-infected plants might also suggest that mycorrhiza efficiently restricted excessive copper and zinc absorptions into the host plants. Compared to the non-infected seedlings, the lead content of infected seedlings was 60% higher in shoots. This might illustrate that mycorrhiza have a different mechanism for protecting its host from excessive lead phytotoxicity by chelating lead in the shoots.

Study of Corrosion Resistance Improvement by Metallic Coating for Overhead Transmission Line Conductor

NASA Astrophysics Data System (ADS)

Isozaki, Masanori; Adachi, Kouichi; Hita, Takanori; Asano, Yuji

Applying anti-corrosion grease and aluminum clad steel (AC) wires to ACSR has adopted as general methods to prevent overhead transmission line conductors and/or wires from corrosion. However, there are some cases that ineffectiveness of those means are reported on some transmission lines passing through acid atmosphere in the vicinity of a factory exhausting acid smoke. The feature of the corrosion caused by acid atmosphere is to show a higher speed in its progressing as well known. As means against such acid corrosion, application of high purity aluminum, selective removal of inter-metallic compound in aluminum and plastic coating wires has been reported before, and each has both of advantage and disadvantage actually. In the former letter, we reported the new type of anti-corrosion grease that shows an excellent property against acid atmosphere as well as in a salty circumstance. Here presents a new type of anti-corrosion technology of applying high corrosion resistance aluminum alloy or zinc coatings on each component wires of a conductor that we succeed in developing through a serial study of anti-corrosion methods on overhead transmission lines.

Byproduct Metal Availability Constrained by Dynamics of Carrier Metal Cycle: The Gallium-Aluminum Example.

PubMed

Løvik, Amund N; Restrepo, Eliette; Müller, Daniel B

2016-08-16

Future availability of byproduct metals is not limited by geological stocks, but by the rate of primary production of their carrier metals, which in turn depends on the development of their in-use stocks, the product lifetimes, and the recycling rates. This linkage, while recognized conceptually in past studies, has not been adequately taken into account in resource availability estimates. Here, we determine the global supply potential for gallium up to 2050 based on scenarios for the global aluminum cycle, and compare it with scenarios for gallium demand derived from a dynamic model of the gallium cycle. We found that the gallium supply potential is heavily influenced by the development of the in-use stocks and recycling rates of aluminum. With current applications, a shortage of gallium is unlikely by 2050. However, the gallium industry may need to introduce ambitious recycling- and material efficiency strategies to meet its demand. If in-use stocks of aluminum saturate or decline, a shift to other gallium sources such as zinc or coal fly ash may be required.

Metal interferences and their removal prior to the determination of As(T) and As(III) in acid mine waters by hydride generation atomic absorption spectrometry

USGS Publications Warehouse

McCleskey, R. Blaine; Nordstrom, D. Kirk; Ball, James W.

2003-01-01

Hydride generation atomic absorption spectrometry (HGAAS) is a sensitive and selective method for the determination of total arsenic (arsenic(III) plus arsenic(V)) and arsenic(III); however, it is subject to metal interferences for acid mine waters. Sodium borohydride is used to produce arsine gas, but high metal concentrations can suppress arsine production. This report investigates interferences of sixteen metal species including aluminum, antimony(III), antimony(V), cadmium, chromium(III), chromium(IV), cobalt, copper(II), iron(III), iron(II), lead, manganese, nickel, selenium(IV), selenium(VI), and zinc ranging in concentration from 0 to 1,000 milligrams per liter and offers a method for removing interfering metal cations with cation exchange resin. The degree of interference for each metal without cation-exchange on the determination of total arsenic and arsenic(III) was evaluated by spiking synthetic samples containing arsenic(III) and arsenic(V) with the potential interfering metal. Total arsenic recoveries ranged from 92 to 102 percent for all metals tested except antimony(III) and antimony(V) which suppressed arsine formation when the antimony(III)/total arsenic molar ratio exceeded 4 or the antimony(V)/total arsenic molar ratio exceeded 2. Arsenic(III) recoveries for samples spiked with aluminum, chromium(III), cobalt, iron(II), lead, manganese, nickel, selenium(VI), and zinc ranged from 84 to 107 percent over the entire concentration range tested. Low arsenic(III) recoveries occurred when the molar ratios of metals to arsenic(III) were copper greater than 120, iron(III) greater than 70, chromium(VI) greater than 2, cadmium greater than 800, antimony(III) greater than 3, antimony(V) greater than 12, or selenium(IV) greater than 1. Low recoveries result when interfering metals compete for available sodium borohydride, causing incomplete arsine production, or when the interfering metal oxidizes arsenic(III). Separation of interfering metal cations using cation-exchange prior to hydridegeneration permits accurate arsenic(III) determinations in acid mine waters containing high concentrations of interfering metals. Stabilization of the arsenic redox species for as many as 15 months is demonstrated for samples that have been properly filtered and acidified with HCl in the field. The detection limits for the method described in this report are 0.1 micrograms per liter for total arsenic and 0.8 micrograms per liter for arsenic(III).

Zinc, iron, and lead: relations to head start children's cognitive scores and teachers' ratings of behavior.

PubMed

Hubbs-Tait, Laura; Kennedy, Tay Seacord; Droke, Elizabeth A; Belanger, David M; Parker, Jill R

2007-01-01

The objective of this study was to conduct a preliminary investigation of lead, zinc, and iron levels in relation to child cognition and behavior in a small sample of Head Start children. The design was cross-sectional and correlational. Participants were 42 3- to 5-year-old children attending rural Head Start centers. Nonfasting blood samples of whole blood lead, plasma zinc, and ferritin were collected. Teachers rated children's behavior on the California Preschool Social Competency Scale, Howes' Sociability subscale, and the Preschool Behavior Questionnaire. Children were tested individually with the McCarthy Scales of Children's Abilities. Hierarchical regression analyses revealed that zinc and ferritin jointly explained 25% of the variance in McCarthy Scales of Children's Abilities verbal scores. Lead levels explained 25% of the variance in teacher ratings of girls' sociability and 20% of the variance in teacher ratings of girls' classroom competence. Zinc levels explained 39% of the variance in teacher ratings of boys' anxiety. Univariate analysis of variance revealed that the four children low in zinc and iron had significantly higher blood lead (median=0.23 micromol/L [4.73 microg/dL]) than the 31 children sufficient in zinc or iron (median=0.07 micromol/L [1.54 microg/dL]) or the 7 children sufficient in both (median=0.12 micromol/L [2.52 microg/dL]), suggesting an interaction among the three minerals. Within this small low-income sample, the results imply both separate and interacting effects of iron, zinc, and lead. They underscore the importance of studying these three minerals in larger samples of low-income preschool children to make more definitive conclusions.

Quadrupolar magic angle spinning NMR spectra fitted using the Pearson IV function.

PubMed

Mironenko, Roman M; Belskaya, Olga B; Talsi, Valentin P; Likholobov, Vladimir A

2014-01-01

The Pearson IV function was used to fit the asymmetric solid-state (27)Al NMR spectra of alumina based catalysts. A high convergence (correlation coefficient is no less than 0.997) between experimental and simulated spectra was achieved. The decomposition of the (27)Al NMR spectra of zinc/aluminum mixed oxides with different Zn/Al molar ratio revealed an increased fraction (6-9%) of pentacoordinated aluminum atoms in these oxides as compared to γ-Al2O3. As the Zn/Al ratio is raised, the fraction of [AlO6] octahedral units decreases, while the fraction of [AlO4] tetrahedra increases. Copyright © 2014 Elsevier Inc. All rights reserved.

Quantification and Simulation of Metal Loading to the Upper Animas River, Eureka to Silverton, San Juan County, Colorado, September 1997 and August 1998

USGS Publications Warehouse

Paschke, Suzanne S.; Kimball, Briant A.; Runkel, Robert L.

2005-01-01

Drainage from abandoned and inactive mines and from naturally mineralized areas in the San Juan Mountains of southern Colorado contributes metals to the upper Animas River near Silverton, Colorado. Tracer-injection studies and associated synoptic sampling were performed along two reaches of the upper Animas River to develop detailed profiles of stream discharge and to locate and quantify sources of metal loading. One tracer-injection study was performed in September 1997 on the Animas River reach from Howardsville to Silverton, and a second study was performed in August 1998 on the stream reach from Eureka to Howardsville. Drainage in the upper Animas River study reaches contributed aluminum, calcium, copper, iron, magnesium, manganese, sulfate, and zinc to the surface-water system in 1997 and 1998. Colloidal aluminum, dissolved copper, and dissolved zinc were attenuated through a braided stream reach downstream from Eureka. Instream dissolved copper concentrations were lower than the State of Colorado acute and chronic toxicity standards downstream from the braided reach to Silverton. Dissolved iron load and concentrations increased downstream from Howardsville and Arrastra Gulch, and colloidal iron remained constant at low concentrations downstream from Howardsville. Instream sulfate concentrations were lower than the U.S. Environmental Protection Agency's secondary drinking-water standard of 250 milligrams per liter throughout the two study reaches. Elevated zinc concentrations are the primary concern for aquatic life in the upper Animas River. In the 1998 Eureka to Howardsville study, instream dissolved zinc load increased downstream from the Forest Queen mine, the Kittimack tailings, and Howardsville. In the 1997 Howardsville to Silverton study, there were four primary areas where zinc load increased. First, was the increase downstream from Howardsville and abandoned mining sites downstream from the Cunningham Gulch confluence, which also was measured during the 1998 study. The second affected reach was downstream from Arrastra Gulch, where the increase in zinc load seems related to a series of right-bank inflows with low pH Quantification and Simulation of Metal Loading to the Upper Animas River, Eureka to Silverton, San Juan County, Colorado, September 1997 and August 1998By Suzanne S. Paschke, Briant A. Kimball, and Robert L. Runkeland elevated dissolved zinc concentrations. A third increase in zinc load occurred 6,100 meters downstream from the 1997 injection site and may have been from ground-water discharge with elevated zinc concentrations based on mass-loading graphs and the lack of visible inflow in the reach. A fourth but lesser dissolved zinc load increase occurred downstream from tailings near the Lackawanna Mill. Results of the tracer-injection studies and the effects of potential remediation were analyzed using the one- dimensional stream-transport computer code OTIS. Based on simulation results, instream zinc concentrations downstream from the Kittimack tailings to upstream from Arrastra Gulch would approach 0.16 milligram per liter (the upper limit of acute toxicity for some sensitive aquatic species) if zinc inflow concentrations were reduced by 75 percent in the stream reaches receiving inflow from the Forest Queen mine, the Kittimack tailings, and downstream from Howardsville. However, simulated zinc concentrations downstream from Arrastra Gulch were higher than approximately 0.30 milligram per liter due to numerous visible inflows and assumed ground-water discharge with elevated zinc concentrations in the lower part of the study reach. Remediation of discrete visible inflows seems a viable approach to reducing zinc inflow loads to the upper Animas River. Remediation downstream from Arrastra Gulch is more complicated because ground-water discharge with elevated zinc concentrations seems to contribute to the instream zinc load.

Organosiloxane-grafted natural polymer coatings

DOEpatents

Sugama, Toshifumi

1998-01-01

A new family of polysaccharide graft polymers are provided as corrosion resistant coatings having antimicrobial properties which are useful on light metals such as aluminum, magnesium, zinc, steel and their alloys. Methods of making the polysaccharide graft polymers are also included. The methods of making the polysaccharide graft polymers involve reacting a polysaccharide source with an antimicrobial agent under conditions of hydrolysis-condensation.

Organosiloxane-grafted natural polymer coatings

DOEpatents

Sugama, Toshifumi

1998-12-01

A new family of polysaccharide graft polymers are provided as corrosion resistant coatings having antimicrobial properties which are useful on light metals such as aluminum, magnesium, zinc, steel and their alloys. Methods of making the polysaccharide graft polymers are also included. The methods of making the polysaccharide graft polymers involve reacting a polysaccharide source with an antimicrobial agent under conditions of hydrolysis-condensation. 17 figs.

High Transparent Conductive Aluminum-Doped Zinc Oxide Thin Films by Reactive Co-Sputtering (Postprint)

DTIC Science & Technology

2016-03-30

wavelength where n = k) is 1605 nm from the film (f). Figure 1 XRD patterns of the AZO films on quartz substrate Figure 2 UV-Vis-NIR...71.6 1605 9.87 x10 -4 Figure 3 Refractive index n (left) and extinction coefficient k of (right) the AZO films. 4. Conclusions AZO films were

Polyorganometallosiloxane-2- or -4-pyridine coatings

DOEpatents

Sugama, Toshifumi

1997-01-01

A new family of polyorganometallosiloxane-2- or -4-pyridine compounds are provided for corrosion resistant coatings on light metals such as aluminum, magnesium, zinc, steel and their allows. The novel compounds contain backbones modified by metal alkoxides, metallocenes and metallophthalocyanates where the metal is Zr, Ti, Mo, V, Hf, Nb, Si, B and combinations thereof. Methods of making the new compounds are also provided.

The Substitution of Ion Vapor Deposited (IVD) Aluminum for Cadmium

DTIC Science & Technology

1990-05-25

Coating Spray 1 0.0030 15 nin a 250TF Epoxy Powder Coating Spray 1 0.0030 15 nln @ 250OF Zinc Phosphate Tank Immersion 1 0.0002 Not Required Whitford: P...1candidate protection systems. MCAIR includ ed barrier-type coatings in the corrosion inhibitors ý;iich wMY be controlled by a~r-to-ic regulations that are

Electro-thermal control of aluminum-doped zinc oxide/vanadium dioxide multilayered thin films for smart-device applications

PubMed Central

Skuza, J. R.; Scott, D. W.; Mundle, R. M.; Pradhan, A. K.

2016-01-01

We demonstrate the electro-thermal control of aluminum-doped zinc oxide (Al:ZnO) /vanadium dioxide (VO2) multilayered thin films, where the application of a small electric field enables precise control of the applied heat to the VO2 thin film to induce its semiconductor-metal transition (SMT). The transparent conducting oxide nature of the top Al:ZnO film can be tuned to facilitate the fine control of the SMT of the VO2 thin film and its associated properties. In addition, the Al:ZnO film provides a capping layer to the VO2 thin film, which inhibits oxidation to a more energetically favorable and stable V2O5 phase. It also decreases the SMT of the VO2 thin film by approximately 5–10 °C because of an additional stress induced on the VO2 thin film and/or an alteration of the oxygen vacancy concentration in the VO2 thin film. These results have significant impacts on technological applications for both passive and active devices by exploiting this near-room-temperature SMT. PMID:26884225

Optical and structural properties of Al-doped ZnO thin films by sol gel process.

PubMed

Jun, Min-Chul; Koh, Jung-Hyuk

2013-05-01

Transparent conducting oxide (TCO) materials with high transmittance and good electrical conductivity have been attracted much attention due to the development of electronic display and devices such as organic light emitting diodes (OLEDs), and dye-sensitized solar cells (DSSCs). Aluminum doped zinc oxide thin films (AZO) have been well known for their use as TCO materials due to its stability, cost-effectiveness, good optical transmittance and electrical properties. Especially, AZO thin film, which have low resistivity of 2-4 x 10(-4) omega x cm which is similar to that of ITO films with wide band gap semiconductors. The AZO thin films were deposited on glass substrates by sol-gel spin-coating process. As a starting material, zinc acetate dihydrate (Zn(CH3COO)2 x 2H2O) and aluminum chloride hexahydrate (AlCl3 6H2O) were used. 2-methoxyethanol and monoethanolamine (MEA) were used as solvent and stabilizer, respectively. After deposited, the films were preheated at 300 degrees C on a hotplate and post-heated at 650 degrees C for 1.5 hrs in the furnace. We have studied the structural and optical properties as a function of Al concentration (0-2.5 mol.%).

Fabrication and characteristics of high-performance and high-stability aluminum-doped zinc oxide thin-film transistors

NASA Astrophysics Data System (ADS)

Shan, Dongfang; Han, Dedong; Huang, Fuqing; Tian, Yu; Zhang, Suoming; Qi, Lin; Cong, Yingying; Zhang, Shengdong; Zhang, Xing; Wang, Yi

2014-01-01

Fully transparent aluminum-doped zinc oxide (AZO) thin-film transistors (TFTs) were successfully fabricated on glass substrates at room temperature. Superior properties, such as a high saturation mobility of 59.3 cm2 V-1 s-1, a positive threshold voltage of 1.3 V, a steep subthreshold swing of 122.9 mV/dec, an off-state current on the order of 10-12 A, and an on/off ratio of 2.7 × 108, were obtained. The electrical properties of the AZO TFTs were successively studied within a period of six months. Small property degenerations could be observed from the test results obtained within the study period, which proved the high-performance and high-stability characteristics of AZO TFTs. Furthermore, hysteresis loop scanning of AZO TFTs was performed, and a small hysteresis could be detected in the scanning curves, which suggested the superior properties of a dielectric and a channel-insulator interface. Lastly, we succeeded in manufacturing an organic LED (OLED) flat panel display panel driven by AZO TFTs and obtained an excellent display effect from it. We believe that AZO TFTs are a promising candidate successor to Si-based TFTs in next-generation flat panel displays.

Large Scale Laser Crystallization of Solution-based Alumina-doped Zinc Oxide (AZO) Nanoinks for Highly Transparent Conductive Electrode

PubMed Central

Nian, Qiong; Callahan, Michael; Saei, Mojib; Look, David; Efstathiadis, Harry; Bailey, John; Cheng, Gary J.

2015-01-01

A new method combining aqueous solution printing with UV Laser crystallization (UVLC) and post annealing is developed to deposit highly transparent and conductive Aluminum doped Zinc Oxide (AZO) films. This technique is able to rapidly produce large area AZO films with better structural and optoelectronic properties than most high vacuum deposition, suggesting a potential large-scale manufacturing technique. The optoelectronic performance improvement attributes to UVLC and forming gas annealing (FMG) induced grain boundary density decrease and electron traps passivation at grain boundaries. The physical model and computational simulation developed in this work could be applied to thermal treatment of many other metal oxide films. PMID:26515670

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent... per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead... any 1 day Maximum for monthly average mg/kkg (pounds per billion pounds) of hard lead produced Lead...

40 CFR 421.73 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... produced Lead .000 .000 Zinc .000 .000 (g) Subpart G—Hard Lead Refining Slag Granulation. BAT Effluent... per billion pounds) of hard lead produced Lead .000 .000 Zinc .000 .000 (h) Subpart G—Hard Lead... any 1 day Maximum for monthly average mg/kkg (pounds per billion pounds) of hard lead produced Lead...

25 CFR 215.7 - Advertisement of sale of leases.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING... zinc mining lease of any tract or tracts of restricted or trust allotted and inherited Indian lands... the Secretary of the Interior will offer for sale at public auction a lead and zinc mining lease of...

40 CFR 421.104 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pounds) of tungstic acid (as W) produced Lead 11.490 5.333 Zinc 41.850 17.230 Ammonia (as N) 5,469.000 2... Lead 1.003 0.466 Zinc 3.653 1.504 Ammonia (as N) 477.400 209.900 Total suspended solids 53.720 42.970 p... pounds) of sodium tungstate (as W) produced Lead 0.000 0.000 Zinc 0.000 0.000 Ammonia (as N) 0.000 0.000...

40 CFR 421.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Lead .283 .135 Zinc .983 .411 Ammonia (as N) .000 .000 Total suspended solids 27.600 13.130 pH (1) (1... Antimony 7.491 3.341 Arsenic 5.455 2.245 Lead 1.096 .522 Zinc 3.811 1.592 Ammonia (as N) .000 .000 Total... Antimony .129 .058 Arsenic .094 .039 Lead .019 .009 Zinc .066 .027 Ammonia (as N) .000 .000 Total suspended...

40 CFR 421.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Lead .283 .135 Zinc .983 .411 Ammonia (as N) .000 .000 Total suspended solids 27.600 13.130 pH (1) (1... Antimony 7.491 3.341 Arsenic 5.455 2.245 Lead 1.096 .522 Zinc 3.811 1.592 Ammonia (as N) .000 .000 Total... Antimony .129 .058 Arsenic .094 .039 Lead .019 .009 Zinc .066 .027 Ammonia (as N) .000 .000 Total suspended...

40 CFR 421.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Lead .283 .135 Zinc .983 .411 Ammonia (as N) .000 .000 Total suspended solids 27.600 13.130 pH (1) (1... Antimony 7.491 3.341 Arsenic 5.455 2.245 Lead 1.096 .522 Zinc 3.811 1.592 Ammonia (as N) .000 .000 Total... Antimony .129 .058 Arsenic .094 .039 Lead .019 .009 Zinc .066 .027 Ammonia (as N) .000 .000 Total suspended...

40 CFR 421.104 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pounds) of tungstic acid (as W) produced Lead 11.490 5.333 Zinc 41.850 17.230 Ammonia (as N) 5,469.000 2... Lead 1.003 0.466 Zinc 3.653 1.504 Ammonia (as N) 477.400 209.900 Total suspended solids 53.720 42.970 p... pounds) of sodium tungstate (as W) produced Lead 0.000 0.000 Zinc 0.000 0.000 Ammonia (as N) 0.000 0.000...

40 CFR 421.104 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... pounds) of tungstic acid (as W) produced Lead 11.490 5.333 Zinc 41.850 17.230 Ammonia (as N) 5,469.000 2... Lead 1.003 0.466 Zinc 3.653 1.504 Ammonia (as N) 477.400 209.900 Total suspended solids 53.720 42.970 p... pounds) of sodium tungstate (as W) produced Lead 0.000 0.000 Zinc 0.000 0.000 Ammonia (as N) 0.000 0.000...

40 CFR 421.132 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Lead .283 .135 Zinc .983 .411 Ammonia (as N) .000 .000 Total suspended solids 27.600 13.130 pH (1) (1... Antimony 7.491 3.341 Arsenic 5.455 2.245 Lead 1.096 .522 Zinc 3.811 1.592 Ammonia (as N) .000 .000 Total... Antimony .129 .058 Arsenic .094 .039 Lead .019 .009 Zinc .066 .027 Ammonia (as N) .000 .000 Total suspended...

40 CFR 421.104 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... pounds) of tungstic acid (as W) produced Lead 11.490 5.333 Zinc 41.850 17.230 Ammonia (as N) 5,469.000 2... Lead 1.003 0.466 Zinc 3.653 1.504 Ammonia (as N) 477.400 209.900 Total suspended solids 53.720 42.970 p... pounds) of sodium tungstate (as W) produced Lead 0.000 0.000 Zinc 0.000 0.000 Ammonia (as N) 0.000 0.000...

40 CFR 464.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... copper, lead, zinc, and total phenols. For non-continuous dischargers, annual average mass limitations....0771 0.0421 Lead (T) 0.0791 0.039 Zinc (T) 0.114 0.0431 Maximum for any 1 day Maximum for monthly average Annual average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.77 0.42 0.017 Lead (T) 0.79 0.39 0.022 Zinc (T) 1...

40 CFR 464.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... copper, lead, zinc, and total phenols. For non-continuous dischargers, annual average mass limitations....0771 0.0421 Lead (T) 0.0791 0.039 Zinc (T) 0.114 0.0431 Maximum for any 1 day Maximum for monthly average Annual average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.77 0.42 0.017 Lead (T) 0.79 0.39 0.022 Zinc (T) 1...

40 CFR 464.33 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

.../billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, and total phenols. For non...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 Maximum for... Lead (T) 0.53 0.26 0.0067 Zinc (T) 0.98 0.37 0.0116 1 kg/1,000 kkg (pounds per million pounds) of metal...

40 CFR 464.34 - New source performance standards.

Code of Federal Regulations, 2010 CFR

2010-07-01

... scrubbed) effluent standards for copper, lead, zinc, total phenols, oil and grease, and TSS. For non...) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 Oil and grease 1.34 0.446 TSS 0.67 0.536... average Annual average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.29 0.16 0.0029 Lead (T) 0.53 0.26 0.0067 Zinc (T...

40 CFR 464.33 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

.../billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, and total phenols. For non...) of metal poured Copper (T) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 Maximum for... Lead (T) 0.53 0.26 0.0067 Zinc (T) 0.98 0.37 0.0116 1 kg/1,000 kkg (pounds per million pounds) of metal...

40 CFR 464.34 - New source performance standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... scrubbed) effluent standards for copper, lead, zinc, total phenols, oil and grease, and TSS. For non...) 0.0129 0.0071 Lead (T) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 Oil and grease 1.34 0.446 TSS 0.67 0.536... average Annual average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.29 0.16 0.0029 Lead (T) 0.53 0.26 0.0067 Zinc (T...

Simulation of the mobility of metal - EDTA complexes in groundwater: The influence of contaminant metals

USGS Publications Warehouse

Friedly, J.C.; Kent, D.B.; Davis, J.A.

2002-01-01

Reactive transport simulations were conducted to model chemical reactions between metal - EDTA (ethylenediaminetetraacetic acid) complexes during transport in a mildly acidic quartz - sand aquifer. Simulations were compared with the results of small-scale tracer tests wherein nickel-, zinc-, and calcium - EDTA complexes and free EDTA were injected into three distinct chemical zones of a plume of sewage-contaminated groundwater. One zone had a large mass of adsorbed, sewage-derived zinc; one zone had a large mass of adsorbed manganese resulting from mildly reducing conditions created bythe sewage plume; and one zone had significantly less adsorbed manganese and negligible zinc background. The chemical model assumed that the dissolution of iron(III) from metal - hydroxypolymer coatings on the aquifer sediments by the metal - EDTA complexes was kinetically restricted. All other reactions, including metal - EDTA complexation, zinc and manganese adsorption, and aluminum hydroxide dissolution were assumed to reach equilibrium on the time scale of transport; equilibrium constants were either taken from the literature or determined independently in the laboratory. A single iron(III) dissolution rate constant was used to fit the breakthrough curves observed in the zone with negligible zinc background. Simulation results agreed well with the experimental data in all three zones, which included temporal moments derived from breakthrough curves at different distances downgradient from the injections and spatial moments calculated from synoptic samplings conducted at different times. Results show that the tracer cloud was near equilibrium with respect to Fe in the sediment after 11 m of transport in the Zn-contaminated region but remained far from equilibrium in the other two zones. Sensitivity studies showed that the relative rate of iron(III) dissolution by the different metal - EDTA complexes was less important than the fact that these reactions are rate controlled. Results suggest that the published solubility for ferrihydrite reasonably approximates the Fe solubility of the hydroxypolymer coatings on the sediments. Aluminum may be somewhat more soluble than represented by the equilibrium constant for gibbsite, and its dissolution may be rate controlled when reacting with Ca - EDTA complexes.

Aluminum anode for aluminum-air battery - Part I: Influence of aluminum purity

NASA Astrophysics Data System (ADS)

Cho, Young-Joo; Park, In-Jun; Lee, Hyeok-Jae; Kim, Jung-Gu

2015-03-01

2N5 commercial grade aluminum (99.5% purity) leads to the lower aluminum-air battery performances than 4N high pure grade aluminum (99.99% purity) due to impurities itself and formed impurity complex layer which contained Fe, Si, Cu and others. The impurity complex layer of 2N5 grade Al declines the battery voltage on standby status. It also depletes discharge current and battery efficiency at 1.0 V which is general operating voltage of aluminum-air battery. However, the impurity complex layer of 2N5 grade Al is dissolved with decreasing discharge voltage to 0.8 V. This phenomenon leads to improvement of discharge current density and battery efficiency by reducing self-corrosion reaction. This study demonstrates the possibility of use of 2N5 grade Al which is cheaper than 4N grade Al as the anode for aluminum-air battery.

Water treatment residual (WTR)-coated wood mulch for alleviation of toxic metals and phosphorus from polluted urban stormwater runoff.

PubMed

Soleimanifar, Hanieh; Deng, Yang; Wu, Laying; Sarkar, Dibyendu

2016-07-01

Aluminum-based water treatment residual (WTR)-coated wood mulches were synthesized and tested for removal of heavy metals and phosphorus (P) in synthetic urban stormwater. WTRs are an industrial waste produced from coagulation in water treatment facilities, primarily composed of amorphous aluminum or iron hydroxides. Batch tests showed that the composite filter media could effectively adsorb 97% lead (Pb), 76% zinc (Zn), 81% copper (Cu) and 97% P from the synthetic stormwater (Pb = 100 μg/L, Zn = 800 μg/L, Cu = 100 μg/L, P = 2.30 mg/L, and pH = 7.0) within 120 min, due to the presence of aluminum hydroxides as an active adsorbent. The adsorption was a 2(nd)-order reaction with respect toward each pollutant. Column tests demonstrated that the WTR-coated mulches considerably alleviated the select pollutants under a continuous-flow condition over the entire filtration period. The effluent Pb, Zn, Cu, and P varied at 0.5-8.9%, 33.4-46.7%, 45.8-55.8%, and 6.4-51.9% of their respective initial concentrations with the increasing bed volume from 0 to 50. Synthetic precipitation leaching procedure (SPLP) and toxicity characteristic leaching procedure (TCLP) tests indicated that leached contaminants were all below the U.S. criteria, suggesting that the release of undesired chemicals under rainfall or landfilling conditions is not a concern during application. This study demonstrates that the WTR-coated mulches are a new, low-cost, and effective filter media for urban stormwater treatment. Equally important, this study provides a sustainable approach to beneficially reuse an industrial waste for environmental pollution control. Copyright © 2016 Elsevier Ltd. All rights reserved.

Simultaneous Measurement of Zinc, Copper, Lead and Cadmium in Baby Weaning Food and Powder Milk by DPASV.

PubMed

Sadeghi, Naficeh; Oveisi, Mohammad Reza; Jannat, Behrooz; Hajimahmoodi, Mannan; Behfar, Abdolazim; Behzad, Masoomeh; Norouzi, Narges; Oveisi, Morvarid; Jannat, Behzad

2014-01-01

Apart from the breast milk, infant formula and baby weaning food have a special role in infant diet. Infants and young children are very susceptible to amount of trace elements. Copper and zinc are two elements that add in infant food. Lead and cadmium are heavy metals that enter to food chain unavoidably. DPASV is a benefit and applicable method for measurement of trace elements in food products. In this study, concentration of zinc, copper, lead and cadmium in four brands of baby food (rice and wheat based) and powder milk was analyzed with DPASV and polarograph set. Total Mean ± SE of zinc, copper, lead and cadmium in baby foods (n = 240) were 11.86 ± 1.474 mg/100g, 508.197 ± 83.154 μg/100g, 0.445 ± 0.006, 0.050 ± 0.005 mg/Kg respectively. Also these amount in powder milk (n = 240) were 3.621± 0.529 mg/100g, 403.822 ± 133.953 μg/100g, 0.007 ± 0.003, 0.060 ± 0.040 mg/Kg respectively. Zinc level in baby food type I was higher than lablled value (P = 0.030), but in other brands was not difference. Concentration of copper in all of samples was in labeled range (P > 0.05). In each four products, level of lead and cadmium were lower than the standard limit (P < 0.05). Amount of zinc and lead in baby food I, had difference versus other products. Concentration of zinc, camium in baby food type I, was higher than type II (P = 0.043, 0.001 respectively). Concentration of lead and cadmium in baby food type II, was higher than infant formulas, but are in standard limit.

Zinc in Infection and Inflammation

PubMed Central

Gammoh, Nour Zahi; Rink, Lothar

2017-01-01

Micronutrient homeostasis is a key factor in maintaining a healthy immune system. Zinc is an essential micronutrient that is involved in the regulation of the innate and adaptive immune responses. The main cause of zinc deficiency is malnutrition. Zinc deficiency leads to cell-mediated immune dysfunctions among other manifestations. Consequently, such dysfunctions lead to a worse outcome in the response towards bacterial infection and sepsis. For instance, zinc is an essential component of the pathogen-eliminating signal transduction pathways leading to neutrophil extracellular traps (NET) formation, as well as inducing cell-mediated immunity over humoral immunity by regulating specific factors of differentiation. Additionally, zinc deficiency plays a role in inflammation, mainly elevating inflammatory response as well as damage to host tissue. Zinc is involved in the modulation of the proinflammatory response by targeting Nuclear Factor Kappa B (NF-κB), a transcription factor that is the master regulator of proinflammatory responses. It is also involved in controlling oxidative stress and regulating inflammatory cytokines. Zinc plays an intricate function during an immune response and its homeostasis is critical for sustaining proper immune function. This review will summarize the latest findings concerning the role of this micronutrient during the course of infections and inflammatory response and how the immune system modulates zinc depending on different stimuli. PMID:28629136

Zinc in Infection and Inflammation.

PubMed

Gammoh, Nour Zahi; Rink, Lothar

2017-06-17

Micronutrient homeostasis is a key factor in maintaining a healthy immune system. Zinc is an essential micronutrient that is involved in the regulation of the innate and adaptive immune responses. The main cause of zinc deficiency is malnutrition. Zinc deficiency leads to cell-mediated immune dysfunctions among other manifestations. Consequently, such dysfunctions lead to a worse outcome in the response towards bacterial infection and sepsis. For instance, zinc is an essential component of the pathogen-eliminating signal transduction pathways leading to neutrophil extracellular traps (NET) formation, as well as inducing cell-mediated immunity over humoral immunity by regulating specific factors of differentiation. Additionally, zinc deficiency plays a role in inflammation, mainly elevating inflammatory response as well as damage to host tissue. Zinc is involved in the modulation of the proinflammatory response by targeting Nuclear Factor Kappa B (NF-κB), a transcription factor that is the master regulator of proinflammatory responses. It is also involved in controlling oxidative stress and regulating inflammatory cytokines. Zinc plays an intricate function during an immune response and its homeostasis is critical for sustaining proper immune function. This review will summarize the latest findings concerning the role of this micronutrient during the course of infections and inflammatory response and how the immune system modulates zinc depending on different stimuli.

40 CFR 471.64 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... contact cooling water Cyanide 0.142 0.059 Lead 0.205 0.098 Zinc 0.713 0.298 Ammonia 65.1 28.6 Fluoride 29... 0.021 0.009 Lead 0.030 0.015 Zinc 0.105 0.044 Ammonia 9.59 4.22 Fluoride 4.28 1.90 (f) Extrusion....022 Lead 0.75 0.036 Zinc 0.260 0.109 Ammonia 23.7 10.5 Fluoride 10.6 4.70 (g) Forging spent lubricants...

40 CFR 471.64 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2012 CFR

2012-07-01

... contact cooling water Cyanide 0.142 0.059 Lead 0.205 0.098 Zinc 0.713 0.298 Ammonia 65.1 28.6 Fluoride 29... 0.021 0.009 Lead 0.030 0.015 Zinc 0.105 0.044 Ammonia 9.59 4.22 Fluoride 4.28 1.90 (f) Extrusion....022 Lead 0.75 0.036 Zinc 0.260 0.109 Ammonia 23.7 10.5 Fluoride 10.6 4.70 (g) Forging spent lubricants...

40 CFR 471.64 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2014 CFR

2014-07-01

... contact cooling water Cyanide 0.142 0.059 Lead 0.205 0.098 Zinc 0.713 0.298 Ammonia 65.1 28.6 Fluoride 29... 0.021 0.009 Lead 0.030 0.015 Zinc 0.105 0.044 Ammonia 9.59 4.22 Fluoride 4.28 1.90 (f) Extrusion....022 Lead 0.75 0.036 Zinc 0.260 0.109 Ammonia 23.7 10.5 Fluoride 10.6 4.70 (g) Forging spent lubricants...

40 CFR 471.64 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2011 CFR

2011-07-01

... contact cooling water Cyanide 0.142 0.059 Lead 0.205 0.098 Zinc 0.713 0.298 Ammonia 65.1 28.6 Fluoride 29... 0.021 0.009 Lead 0.030 0.015 Zinc 0.105 0.044 Ammonia 9.59 4.22 Fluoride 4.28 1.90 (f) Extrusion....022 Lead 0.75 0.036 Zinc 0.260 0.109 Ammonia 23.7 10.5 Fluoride 10.6 4.70 (g) Forging spent lubricants...

40 CFR 471.64 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2010 CFR

2010-07-01

... contact cooling water Cyanide 0.142 0.059 Lead 0.205 0.098 Zinc 0.713 0.298 Ammonia 65.1 28.6 Fluoride 29... 0.021 0.009 Lead 0.030 0.015 Zinc 0.105 0.044 Ammonia 9.59 4.22 Fluoride 4.28 1.90 (f) Extrusion....022 Lead 0.75 0.036 Zinc 0.260 0.109 Ammonia 23.7 10.5 Fluoride 10.6 4.70 (g) Forging spent lubricants...

Geologic datasets for weights-of-evidence analysis in northeast Washington: 2. Mineral databases

USGS Publications Warehouse

Boleneus, D.E.

1999-01-01

Digital mineral databases are necessary to carry out weights-of-evidence modeling of mineral resources for epithermal gold and carbonate-hosted lead-zinc deposits in northeast Washington. This report describes spreadsheet tables consisting of: 1) training sites for epithermal gold, 2) placer gold sites, 3) training sites for carbonate-hosted lead-zinc, and 4) small lead-zinc mines and prospects. A fifth table provides location data about sites in the four tables.

Assimilation of zinc, cadmium, lead, copper, and iron by the spider Dysdera crocata, a predator of woodlice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopkin, S.P.; Martin, M.H.

1985-02-01

In this paper, an experiment is described on the assimilation of zinc, cadmium, lead, copper and iron by Dysdera crocata collected from a site in central Bristol. The spiders were fed on woodlice from their own site, and on woodlice from a site contaminated by a smelting works which contained much higher levels of zinc, cadmium and lead than the spiders would have been used to in their normal diet.

40 CFR 464.43 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting... copper, lead, zinc, and total phenols. For non-continuous dischargers, annual average mass limitations....0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 Maximum for any 1 day Maximum for monthly average...

40 CFR 464.43 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting... copper, lead, zinc, and total phenols. For non-continuous dischargers, annual average mass limitations....0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 Maximum for any 1 day Maximum for monthly average...

Toxicity to woodlice of zinc and lead oxides added to soil litter

USGS Publications Warehouse

Beyer, W.N.; Anderson, A.

1985-01-01

Previous studies have shown that high concentrations of metals in soil are associated with reductions in decomposer populations. We have here determined the relation between the concentrations of lead and zinc added as oxides to soil litter and the survival and reproduction of a decomposer population under controlled conditions. Laboratory populations of woodlice (Porcellio scaber Latr) were fed soil litter treated with lead or zinc at concentrations that ranged from 100 to 12,800 ppm. The survival of the adults, the maximum number of young alive, and the average number of young alive, were recorded over 64 weeks. Lead at 12,800 ppm and zinc at 1,600 ppm or more had statistically significant (p < 0.05) negative effects on the populations. These results agree with field observations suggesting that lead and zinc have reduced populations of decomposers in contaminated forest soil litter, and concentrations are similar to those reported to be associated with reductions in natural populations of decomposers. Poisoning of decomposers may disrupt nutrient cycling, reduce the numbers of invertebrates available to other wildlife for food, and contribute to the contamination of food chains.

Final report on COOMET.T-S1. Comparison of type S thermocouples at the freezing points of zinc, aluminium and copper 2014—2015

NASA Astrophysics Data System (ADS)

Pokhodun, A. I.; Ivanova, A. G.; Duysebayeva, K. K.; Ivanova, K. P.

2015-01-01

Regional comparison of type S thermocouples at the freezing points of zinc, aluminium and copper was initiated by COOMET TC1.1-10 (the technical committee of COOMET `Thermometry and thermal physics'). Three NMI take part in COOMET regional comparison: D I Mendeleev Institute for Metrology (VNIIM) (Russian Federation), National Scientific Centre (Institute of Metrology) (NSC IM, Ukraine), Republic State Enterprise (Kazakhstan Institute of Metrology) (KazInMetr, Republic of Kazakhstan). VNIIM (Russia) was chosen as the coordinator-pilot of the regional comparison. A star type comparison was used. The participants: KazInMetr and NSC IM constructed the type S thermocouples and calibrated them in three fixed points: zinc, aluminum and copper points, using methods of ITS-90 fixed point realizations. The thermocouples have been sent to VNIIM together with the results of the calibration at three fixed points, with the values of the inhomogeneity at temperature 200 °C and the uncertainty evaluations of the results. For calibration of thermocouples the same VNIIM fixed points cells were used. Participating laboratories repeated the calibration of thermocouples after its returning in zinc, aluminum and copper points to determine the stability of its results. In result of the comparison was to evaluate the equivalence of the type S thermocouples calibration in fixed points by NMIs to confirm corresponding lines of international website for NMI's Calibration and Measurement Capabilities (CMC). This paper is the final report of the comparison including analysis of the uncertainty of measurement results. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT WG-KC, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Effect of alteration zones on water quality: a case study from Biga Peninsula, Turkey.

PubMed

Baba, Alper; Gunduz, Orhan

2010-04-01

Widespread and intense zones of silicified, propylitic, and argillic alteration can be found in the Can volcanics of Biga Peninsula, northwest Turkey. Most of the springs in the study area surface out from the boundary between fractured aquifer (silicified zone) and impervious boundary (argillic zone). This study focuses on two such springs in Kirazli area (Kirazli and Balaban springs) with a distinct quality pattern. Accordingly, field parameters (temperature, pH, and electrical conductivity), major anion and cation (sodium, potassium, calcium, magnesium, chloride, bicarbonate, and sulfate), heavy metals (aluminum, arsenic, barium, chromium, cobalt, cupper, iron, lithium, manganese, nickel, lead, and zinc), and isotopes (oxygen-18, deuterium, and tritium) were determined in water samples taken from these springs during 2005 through 2007. The chemical analyses showed that aluminum concentrations were found to be two orders of magnitude greater in Kirazli waters (mean value 13813.25 microg/L). The levels of this element exceeded the maximum allowable limits given in national and international standards for drinking-water quality. In addition, Balaban and Kirazli springs are >55 years old according to their tritium levels; Kirazli spring is older than Balaban spring. Kirazli spring is also more enriched than Balaban spring based in oxygen-18 and deuterium values. Furthermore, Kirazli spring water has been in contact with altered rocks longer than Balaban spring water, according to its relatively high chloride and electrical conductivity values.

Preliminary investigation of mineral content of pollen collected from different Serbian maize hybrids - is there any potential nutritional value?

PubMed

Kostić, Aleksandar Ž; Kaluđerović, Lazar M; Dojčinović, Biljana P; Barać, Miroljub B; Babić, Vojka B; Mačukanović-Jocić, Marina P

2017-07-01

Bee pollen has already proved to be a good supplement rich in iron and zinc. Studies on the application of flower pollen in the food industry and medicine have begun. Bearing in mind the prevalence of maize as a crop culture, its pollen will be easily available. The mineral composition of pollen of seven Serbian maize hybrids was analyzed in order to establish its nutritional value and the benefits of its implementation in the human diet using the inductively coupled plasma method. The presence of twenty four different macro- (nine) and micronutrients (fifteen) was detected. The most common minerals were phosphorus and potassium, while arsenic, cobalt, lead, nickel and molybdenum were found in some samples. Comparing the results obtained with recommended or tolerable dietary intake references for adults, it was found that maize pollen can be used as a very good source of zinc, iron, chromium and manganese for humans. With regard to selenium content, pollen samples proved to be moderately good source of this important micronutrient. Contents of some elements (Fe, Zn, Mn, Cr, Se, Al and V) showed significant differences depending on hybrid type. In some samples increased concentrations of aluminum and vanadium were recorded, which may pose a potential problem due to their toxicity. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

[XANES study of lead speciation in duckweed].

PubMed

Chu, Bin-Bin; Luo, Li-Qiang; Xu, Tao; Yuan, Jing; Sun, Jian-Ling; Zeng, Yuan; Ma, Yan-Hong; Yi, Shan

2012-07-01

Qixiashan lead-zinc mine of Nanjing was one of the largest lead zinc deposits in East China Its exploitation has been over 50 years, and the environmental pollution has also been increasing. The lead concentration in the local environment was high, but lead migration and toxic mechanism has not been clear. Therefore, biogeochemistry research of the lead zinc mine was carried out. Using ICP-MS and Pb-L III edge XANES, lead concentration and speciation were analyzed respectively, and duckweed which can tolerate and enriched heavy metals was found in the pollution area. The results showed that the lead concentration of duckweed was 39.4 mg x kg(-1). XANES analysis and linear combination fit indicated that lead stearate and lead sulfide accounted for 65% and 36.9% respectively in the lead speciation of duckweed, suggesting that the main lead speciation of duckweed was sulfur-containing lead-organic acid.

40 CFR 421.253 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... gold refined electrolytically Lead 5.544 2.574 Mercury 2.970 1.188 Silver 5.742 2.376 Zinc 20.200 8.316... smelted Lead 0.364 0.169 Mercury 0.195 0.078 Silver 0.377 0.156 Zinc 1.326 0.546 Gold 0.130 (b) Silver... reduced in solution Lead 0.112 0.052 Mercury 0.060 0.024 Silver 0.116 0.048 Zinc 0.408 0.168 Gold 0.040 (c...

40 CFR 464.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Sm3 or lb/billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, total phenols, oil... Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 Oil and grease 1.34 0.446 TSS 1.7 0.67 pH (1) (1) 1 Within... average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.29 0.16 0.0029 Lead (T) 0.79 0.39 0.0098 Zinc (T) 1.47 0.56 0...

40 CFR 464.32 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Sm3 or lb/billion SCF of air scrubbed) effluent limitations for copper, lead, zinc, total phenols, oil... Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 Oil and grease 1.34 0.446 TSS 1.7 0.67 pH (1) (1) 1 Within... average 1 (mg/l) 2 (mg/l) 2 Copper (T) 0.29 0.16 0.0029 Lead (T) 0.79 0.39 0.0098 Zinc (T) 1.47 0.56 0...

Polyorganometallosiloxane-2- or -4-pyridine coatings

DOEpatents

Sugama, T.

1997-12-30

A new family of polyorganometallosiloxane-2- or -4-pyridine compounds are provided for corrosion resistant coatings on light metals such as aluminum, magnesium, zinc, steel and their alloys. The novel compounds contain backbones modified by metal alkoxides, metallocenes and metallophthalocyanates where the metal is Zr, Ti, Mo, V, Hf, Nb, Si, B and combinations thereof. Methods of making the new compounds are also provided. 13 figs.

Energy, Power & Interconnect Technologies Division Overview

DTIC Science & Technology

2010-02-26

Indiana University, Bloomington, IN, February 26, 2010 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF...Battery Expertise Alkaline (Sealed/Vented) Lithium (Reserve/Active) Thermal Aluminum-Oxygen (Air) Cadmium -Oxygen (Air) Carbon-Zinc Mercury- Cadmium M Zi...Iron Nickel- Cadmium Nickel-Hydrogen Oxyhalide Polymer Sulfur Dioxide Sulfuryl Chloride Thionyl Chloride V di P t id um con o a su e Magnesium/Vanadium

Wood surface modification by in-situ sol-gel deposition of hybrid inorganic-organic thin films

Treesearch

Mandla A. Tshabalala; Li-Piin Sung

2007-01-01

Interest in the use of nanoparticles of iron, titanium, aluminum, and zinc oxides in transparent coatings for wood is increasing. Such nano-composite coatings have the potential of not only preserving the natural color of the wood, but also stabilizing the wood surface against the combined degradative effects of sunlight and moisture. The nanoparticles can be used as...

40 CFR 467.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... extruded Chromium 0.15 0.061 Cyanide 0.098 0.041 Zinc 0.49 0.21 TTO 0.23 Oil and grease (alternate... for any 1 day Maximum for monthly average mg/off-kg (lb/million off-lbs) of extruded Chromium 0.65 0... 1 day Maximum for monthly average mg/off-kg (lb/million off-lbs) of aluminum cast Chromium 0.59 0.24...

40 CFR 464.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc... for copper, lead, zinc, total phenols, oil and grease, and TSS. For non-continuous dischargers, annual... metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0353 0.0174 Zinc (T) 0.0509 0.0192 Oil and grease 1.34...

40 CFR 464.42 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc... for copper, lead, zinc, total phenols, oil and grease, and TSS. For non-continuous dischargers, annual... metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0353 0.0174 Zinc (T) 0.0509 0.0192 Oil and grease 1.34...

25 CFR 215.11 - New leases where prior leases have been forfeited or abandoned.

Code of Federal Regulations, 2011 CFR

2011-04-01

... MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.11 New leases where prior leases... zinc ores have been discovered but the mines and mining operations have been abandoned and the leases... to the highest bidder. If the lead and zinc mining lease on said land be offered for sale at public...

The Role of Trace Elements in Tinnitus.

PubMed

Yaşar, Mehmet; Şahin, Mehmet İlhan; Karakükçü, Çiğdem; Güneri, Erhan; Doğan, Murat; Sağıt, Mustafa

2017-03-01

In this study, we aimed to investigate the role of three trace elements, namely, zinc, copper, and lead, in tinnitus by analyzing the serum level of copper and lead and both the serum and tissue level of zinc. Eighty patients, who applied to outpatient otolaryngology clinic with the complaints of having tinnitus, and 28 healthy volunteers were included. High-frequency audiometry was performed, and participants who had hearing loss according to the pure tone average were excluded; tinnitus frequency and loudness were determined and tinnitus reaction questionnaire scores were obtained from the patients. Of all the participants, serum zinc, copper, and lead values were measured; moreover, zinc levels were examined in hair samples. The levels of trace elements were compared between tinnitus and control groups. The level of copper was found to be significantly lower in the tinnitus group (p = 0.02), but there was no significant difference between the groups in terms of the levels of zinc, neither in serum nor in hair, and lead in serum (p > 0.05). The lack of trace elements, especially that of "zinc," have been doubted for the etiopathogenesis of tinnitus in the literature; however, we only found copper levels to be low in patients having tinnitus.

Comprehensive recovery of gold and base-metal sulfide minerals from a low-grade refractory ore

NASA Astrophysics Data System (ADS)

Li, Wen-juan; Liu, Shuang; Song, Yong-sheng; Wen, Jian-kang; Zhou, Gui-ying; Chen, Yong

2016-12-01

The comprehensive recovery of small amounts of valuable minerals such as gold and base-metal sulfide minerals from a low-grade refractory ore was investigated. The following treatment strategy was applied to a sample of this ore: gold flotation-gold concentrate leaching-lead and zinc flotation from the gold concentrate leaching residue. Closed-circuit trials of gold flotation yielded a gold concentrate that assayed at 40.23 g·t-1 Au with a recovery of 86.25%. The gold concentrate leaching rate was 98.76%. Two variants of lead-zinc flotation from the residue—preferential flotation of lead and zinc and bulk flotation of lead and zinc—were tested using the middling processing method. Foam from the reflotation was returned to the lead rougher flotation or lead-zinc bulk flotation, whereas middlings from reflotation were discarded. Sulfur concentrate was a byproduct. The combined strategy of flotation, leaching, and flotation is recommended for the treatment of this kind of ore.

Influence of zinc, lead, and cadmium pollutants on the microflora of hawthorn leaves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bewley, R.J.F.; Campbell, R.

1980-01-01

Transect studies were conducted to determine the relative effects of zinc, lead, and cadmium pollution on microorganisms occurring on hawthorn leaves at varying distances from a smelting complex. Sporobolomyces roseus was absent from the most heavily contaminated leaves but, although lead was inhibitory, other environmental factors were also important in determining its overall population level. Conversely, Aureobasidium pullulans and nonpigmented yeasts showed a significant partial positive correlation with lead but were inhibited by zinc and/or cadmium. Numbers of bacterial colonies were only slightly reduced by the combined effect of all three metals, but total numbers of bacteria were highly negativelymore » correlated with lead. Filamentous fungi, isolated by leaf washing, were only slightly inhibited by all three metals, and the degree of mycelial proliferation on senescent leaves was little affected by heavy metal pollution. Computer-generated maps were produced of the distribution of A. pullulans in relation to zinc and lead fallout. 14 references, 7 figures, 2 tables.« less

Oxidative potential and inflammatory impacts of source apportioned ambient air pollution in Beijing.

PubMed

Liu, Qingyang; Baumgartner, Jill; Zhang, Yuanxun; Liu, Yanju; Sun, Yongjun; Zhang, Meigen

2014-11-04

Air pollution exposure is associated with a range of adverse health impacts. Knowledge of the chemical components and sources of air pollution most responsible for these health effects could lead to an improved understanding of the mechanisms of such effects and more targeted risk reduction strategies. We measured daily ambient fine particulate matter (<2.5 μm in aerodynamic diameter; PM2.5) for 2 months in peri-urban and central Beijing, and assessed the contribution of its chemical components to the oxidative potential of ambient air pollution using the dithiothreitol (DTT) assay. The composition data were applied to a multivariate source apportionment model to determine the PM contributions of six sources or factors: a zinc factor, an aluminum factor, a lead point factor, a secondary source (e.g., SO4(2-), NO3(2-)), an iron source, and a soil dust source. Finally, we assessed the relationship between reactive oxygen species (ROS) activity-related PM sources and inflammatory responses in human bronchial epithelial cells. In peri-urban Beijing, the soil dust source accounted for the largest fraction (47%) of measured ROS variability. In central Beijing, a secondary source explained the greatest fraction (29%) of measured ROS variability. The ROS activities of PM collected in central Beijing were exponentially associated with in vivo inflammatory responses in epithelial cells (R2=0.65-0.89). We also observed a high correlation between three ROS-related PM sources (a lead point factor, a zinc factor, and a secondary source) and expression of an inflammatory marker (r=0.45-0.80). Our results suggest large differences in the contribution of different PM sources to ROS variability at the central versus peri-urban study sites in Beijing and that secondary sources may play an important role in PM2.5-related oxidative potential and inflammatory health impacts.

The effects of CaEDTA injection on lead, zinc, copper and ALAD in erythrocyte, plasma and urine in lead-exposed workers: a 24-h observation.

PubMed

Aono, H; Araki, S

1984-01-01

To evaluate the effects of calcium disodium ethylenediamine tetraacetate (CaEDTA) on the concentrations of lead, zinc and copper in plasma, erythrocyte and urine, and the delta-aminolevulinic acid dehydratase (ALAD) activity in erythrocyte, we administered CaEDTA in 1-h intravenous infusion to ten male gun metal founders with blood-lead concentration of 39 to 64 micrograms/dl (mean 49 micrograms/dl). We found that the plasma concentration of lead, following a rapid rise within the first 3 h, fell temporarily to the level significantly lower than the initial level 19 h after start of the infusion. The plasma concentration of zinc fell to the minimal level 5 h after the infusion; and the erythrocyte concentration of zinc and the ALAD activity concurrently rose to the maximal level 5 h after the infusion. By contrast, no significant alteration was observed in the concentrations of copper in plasma and erythrocyte. The maximal level of urinary metal excretion was attained during the period between 1 and 2 h after start of CaEDTA infusion for lead; within 2 h for zinc; and between 2 and 4 h for copper. The urinary metal excretion returned to the initial level 14 to 24 h after infusion for zinc and copper; but lead excretion was still higher than the initial level during this period. The difference in the kinetics of the three metals following CaEDTA injection is discussed in the light of these findings.

Preparation and adsorption characteristics for heavy metals of active silicon adsorbent from leaching residue of lead-zinc tailings.

PubMed

Lei, Chang; Yan, Bo; Chen, Tao; Xiao, Xian-Ming

2018-05-19

To comprehensively reuse the leaching residue obtained from lead-zinc tailings, an active silicon adsorbent (ASA) was prepared from leaching residue and studied as an adsorbent for copper(II), lead(II), zinc(II), and cadmium(II) in this paper. The ASA was prepared by roasting the leaching residue with either a Na 2 CO 3 /residue ratio of 0.6:1 at 700 °C for 1 h or a CaCO 3 /residue ratio of 0.8:1 at 800 °C for 1 h. Under these conditions, the available SiO 2 content of the ASA was more than 20%. The adsorption behaviors of the metal ions onto the ASA were investigated and the Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models were used to analyze the adsorption isotherm. The result showed that the maximum adsorption capacities of copper(II), lead(II), cadmium(II), and zinc(II) calculated by the Langmuir model were 3.40, 2.83, 0.66, and 0.62 mmol g -1 , respectively. The FT-IR spectra of the ASA and the mean free adsorption energies indicated that ion exchange was the mechanism of copper(II), lead(II), and cadmium(II) adsorption and that chemical reaction was the mechanism of zinc(II) adsorption. These results provide a method for reusing the leaching residue obtained from lead-zinc tailings and show that the ASA is an effective adsorbent for heavy metal pollution remediation.

First principle study of AlX (X=3d, 4d, 5d elements and Lu) dimer.

PubMed

Ouyang, Yifang; Wang, Jianchuan; Hou, Yuhua; Zhong, Xiaping; Du, Yong; Feng, Yuanping

2008-02-21

The ground state equilibrium bond length, harmonic vibrational frequency, and dissociation energy of AlX (X=3d,4d,5d elements and Lu) dimers are investigated by density functional method B3LYP. The present results are in good agreement with the available experimental and other theoretical values except the dissociation energy of AlCr. The present calculations show that the late transition metal can combine strongly with aluminum compared with the former transition metal. The present calculation also indicates that it is more reasonable to replace La with Lu in the Periodic Table and that the bonding strengths of zinc, cadmium, and mercury with aluminum are very weak.

Organosilane self-assembled layers (SAMs) and hybrid silicate magnesium-rich primers for the corrosion protection of aluminum alloy 2024 T3

NASA Astrophysics Data System (ADS)

Wang, Duhua

Although current chromate coatings function very well in corrosion protection for aircraft alloys, such as aluminum alloy 2024 T3, the U.S. Environmental Protection Agency is planning to totally ban the use of chromates as coating materials in the next decade or so because of their extremely toxic effect. For this purpose, both self-assembled layers and silicate magnesium-rich primers were tested to provide the corrosion protection for aluminum alloy. The long-term goal of this research is to develop a coating system to replace the current chromate coating for aircraft corrosion protection. Aluminum alloy 2024 T3 substrates were modified with self-assembled monolayer or multilayer thin films from different alkylsilane compounds. Mono-functional silanes, such as octadecyltrichlorosilane (C18SiCl3), can form a mixed hydrophobic monolayer or multilayer thin film on the aluminum oxide surface to provide a barrier to water and other electrolytes, so the corrosion resistance of the SAMs modified surface was increased significantly. On the other hand, the bi-functional silane self-assembly could attach the aluminum surface through the silicon headgroup while using its functional tailgroup to chemically bond the polymer coating, thus improving the adhesion between the aluminum substrate and coating substantially, and seems to contribute more to corrosion protection of aluminum substrate. Organosilanes were also combined with tetraethyl orthosilicate (TEOS) in propel ratios to form a sol-gel binder to make silicate magnesium-rich primers. Analogue to the inorganic zinc-rich coatings, the silicate magnesium-rich primers also showed excellent adhesion and solvent resistance. The sacrificial magnesium pigments and the chemically inert silicate binder both contribute to the anti-corrosion properties. Future studies will be focused on the formula optimization for better toughness, chemical resistance and anticorrosion performance.

Effect of Al2O3 insulator thickness on the structural integrity of amorphous indium-gallium-zinc-oxide based thin film transistors.

PubMed

Kim, Hak-Jun; Hwang, In-Ju; Kim, Youn-Jea

2014-12-01

The current transparent oxide semiconductors (TOSs) technology provides flexibility and high performance. In this study, multi-stack nano-layers of TOSs were designed for three-dimensional analysis of amorphous indium-gallium-zinc-oxide (a-IGZO) based thin film transistors (TFTs). In particular, the effects of torsional and compressive stresses on the nano-sized active layers such as the a-IGZO layer were investigated. Numerical simulations were carried out to investigate the structural integrity of a-IGZO based TFTs with three different thicknesses of the aluminum oxide (Al2O3) insulator (δ = 10, 20, and 30 nm), respectively, using a commercial code, COMSOL Multiphysics. The results are graphically depicted for operating conditions.

Remediation of arsenic and lead with nanocrystalline zinc sulfide.

PubMed

Piquette, Alan; Cannon, Cody; Apblett, Allen W

2012-07-27

Nanocrystalline (1.7 ± 0.3 nm) zinc sulfide with a specific surface area up to 360 m(2) g(-1) was prepared from the thermal decomposition of a single-source precursor, zinc ethylxanthate. Zinc ethylxanthate decomposes to cubic zinc sulfide upon exposure to temperatures greater than or equal to 125 °C. The resulting zinc sulfide was tested as a water impurity extractant. The target impurities used in this study were As(5+), As(3+), and Pb(2+). The reaction of the nanocrystalline ZnS with Pb(2+) proceeds as a replacement reaction where solid PbS is formed and Zn(2+) is released into the aqueous system. Removal of lead to a level of less than two parts per billion is achievable. The results of a detailed kinetics experiment between the ZnS and Pb(2+) are included in this study. Unlike the instance of lead, both As(5+) and As(3+) adsorb on the surface of the ZnS extractant as opposed to an ion-exchange process. An uptake capacity of > 25 mg g(-1) for the removal of As(5+) is possible. The uptake of As(3+) appears to proceed by a slower process than that of the As(5+) with a capacity of nearly 20 mg g(-1). The nanocrystalline zinc sulfide was extremely successful for the removal of arsenic and lead from simulated oil sand tailing pond water.

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 421.116 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... pounds) of concentrate digested Lead .174 .081 Zinc .635 .261 Ammonia (as N) 82.910 36.450 Fluoride 21... Lead 2.592 1.203 Zinc 9.442 3.888 Ammonia (as N) 1,233.000 542.5000 Fluoride 324.000 185.100 (c... .069 .032 Zinc .251 .103 Ammonia (as N) 32.790 14.420 Fluoride 8.610 4.920 (d) Subpart K—Precipitation...

40 CFR 464.46 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting Subcategory § 464.46... million pounds) of metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 TTO... million pounds) of metal poured Copper (T) 0.0066 0.0036 Lead (T) 0.0046 0.0022 Zinc (T) 0.0066 0.0025...

40 CFR 464.46 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Zinc Casting Subcategory § 464.46... million pounds) of metal poured Copper (T) 0.0344 0.0187 Lead (T) 0.0237 0.0116 Zinc (T) 0.0339 0.0129 TTO... million pounds) of metal poured Copper (T) 0.0066 0.0036 Lead (T) 0.0046 0.0022 Zinc (T) 0.0066 0.0025...

40 CFR 464.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to plants that are casting primarily steel, to... Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting Quench Operations. (1) Applicable to plants... Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO 0.0257 0.00838 Oil and grease...

40 CFR 464.35 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) 0.0237 0.0116 Zinc (T) 0.0437 0.0165 (2) Applicable to plants that are casting primarily steel, to... Lead (T) 0.0353 0.0174 Zinc (T) 0.0656 0.025 (b) Casting Quench Operations. (1) Applicable to plants... Copper (T) 0.0138 0.0076 Lead (T) 0.0252 0.0124 Zinc (T) 0.0466 0.0176 TTO 0.0257 0.00838 Oil and grease...

Iron and aluminum interaction with amyloid-beta peptides associated with Alzheimer's disease

NASA Astrophysics Data System (ADS)

Drochioiu, Gabi; Murariu, Manuela; Ion, Laura; Habasescu, Laura

2014-10-01

An elevation in the concentration of heavy metal ions in Alzheimer's disease (AD) brain has been demonstrated in many studies. Aβ precipitation and toxicity in AD brains seem to be caused by abnormal interactions with neocortical metal ions, especially iron, copper, zinc, and aluminum [1-3]. There is increasing evidence that iron and aluminum ions are involved in the mechanisms that underlie the neurodegenerative diseases [4,5]. However, evidence was brought to demonstrate that some Aβ fragments, at physiological pH, are not able to form binary complexes with Fe(III) ions of sufficient stability to compete with metal hydroxide precipitation [6]. On the contrary, multiple metal ions are known to interact with Aβ peptides [7]. Consequently, we investigated here the interaction of Fe(II/III) and Al(III) ions with some amyloid-β peptides and fragments that results in peptide aggregation and fibrillation [8,9]. Infrared spectroscopy, atomic force microscopy, scanning electron microscopy, electrophoresis and mass spectrometry demonstrated conformational changes of peptides in the presence of such metals.

Heat storage in alloy transformations

NASA Technical Reports Server (NTRS)

Birchenall, C. E.

1980-01-01

The feasibility of using metal alloys as thermal energy storage media was investigated. The elements selected as candidate media were limited to aluminum, copper, magnesium, silicon, zinc, calcium, and phosphorus on the basis of low cost and latent heat of transformation. Several new eutectic alloys and ternary intermetallic phases were determined. A new method employing X-ray absorption techniques was developed to determine the coefficients of thermal expansion of both the solid and liquid phases and the volume change during phase transformation. The method and apparatus are discussed and the experimental results are presented for aluminum and two aluminum-eutectic alloys. Candidate materials were evaluated to determine suitable materials for containment of the metal alloys. Graphite was used to contain the alloys during the volume change measurements. Silicon carbide was identified as a promising containment material and surface-coated iron alloys were also evaluated. System considerations that are pertinent if alloy eutectics are used as thermal energy storage media are discussed. Potential applications to solar receivers and industrial furnaces are illustrated schematically.

Effects of lead and zinc mining contamination on bacterial community diversity and enzyme activities of vicinal cropland.

PubMed

Qu, Juanjuan; Ren, Guangming; Chen, Bao; Fan, Jinghua; E, Yong

2011-11-01

In the process of mining activity, many kinds of heavy metals enter into soils with dust, causing serious contamination to the environment. In this study, six soils were sampled from cropland at different distances from a lead/zinc mine in Heilongjiang Province, China. The total contents of lead and zinc in the vicinal cropland exceeded the third level of environmental quality standard for soil in China, which indicated that soils in this area were moderately contaminated. Bacterial community diversity and population were greatly decreased when the concentrations of lead and zinc were beyond 1,500 and 995 mg kg(-1), respectively, as analyzed by plate counting and polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE). The bands of DGGE patterns varied with the degree of contamination. The activities of soil urease, phosphatase, and dehydrogenase were negatively correlated with the concentrations of lead and zinc. The highest inhibitory effect of heavy metals on soil enzyme activities was observed in urease. It was noted that PCR-DGGE patterns combined with soil enzyme activity analysis can be indices for the soil quality assessment by heavy metal contamination.

Synthesis and characterization of single-crystalline zinc tin oxide nanowires

NASA Astrophysics Data System (ADS)

Shi, Jen-Bin; Wu, Po-Feng; Lin, Hsien-Sheng; Lin, Ya-Ting; Lee, Hsuan-Wei; Kao, Chia-Tze; Liao, Wei-Hsiang; Young, San-Lin

2014-05-01

Crystalline zinc tin oxide (ZTO; zinc oxide with heavy tin doping of 33 at.%) nanowires were first synthesized using the electrodeposition and heat treatment method based on an anodic aluminum oxide (AAO) membrane, which has an average diameter of about 60 nm. According to the field emission scanning electron microscopy (FE-SEM) results, the synthesized ZTO nanowires are highly ordered and have high wire packing densities. The length of ZTO nanowires is about 4 μm, and the aspect ratio is around 67. ZTO nanowires with a Zn/(Zn + Sn) atomic ratio of 0.67 (approximately 2/3) were observed from an energy dispersive spectrometer (EDS). X-ray diffraction (XRD) and corresponding selected area electron diffraction (SAED) patterns demonstrated that the ZTO nanowire is hexagonal single-crystalline. The study of ultraviolet/visible/near-infrared (UV/Vis/NIR) absorption showed that the ZTO nanowire is a wide-band semiconductor with a band gap energy of 3.7 eV.

Synthesis and characterization of single-crystalline zinc tin oxide nanowires.

PubMed

Shi, Jen-Bin; Wu, Po-Feng; Lin, Hsien-Sheng; Lin, Ya-Ting; Lee, Hsuan-Wei; Kao, Chia-Tze; Liao, Wei-Hsiang; Young, San-Lin

2014-01-01

Crystalline zinc tin oxide (ZTO; zinc oxide with heavy tin doping of 33 at.%) nanowires were first synthesized using the electrodeposition and heat treatment method based on an anodic aluminum oxide (AAO) membrane, which has an average diameter of about 60 nm. According to the field emission scanning electron microscopy (FE-SEM) results, the synthesized ZTO nanowires are highly ordered and have high wire packing densities. The length of ZTO nanowires is about 4 μm, and the aspect ratio is around 67. ZTO nanowires with a Zn/(Zn + Sn) atomic ratio of 0.67 (approximately 2/3) were observed from an energy dispersive spectrometer (EDS). X-ray diffraction (XRD) and corresponding selected area electron diffraction (SAED) patterns demonstrated that the ZTO nanowire is hexagonal single-crystalline. The study of ultraviolet/visible/near-infrared (UV/Vis/NIR) absorption showed that the ZTO nanowire is a wide-band semiconductor with a band gap energy of 3.7 eV.

Effect of Zinc Oxide Doping on Electroluminescence and Electrical Behavior of Metalloporphyrins-Doped Samarium Complex

NASA Astrophysics Data System (ADS)

Janghouri, Mohammad; Amini, Mostafa M.

2018-02-01

Samarium complex [(Sm(III)] as a new host material was used for preparation of red organic light-emitting diodes (OLEDs). Devices with configurations of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):(poly(styrenesulfonate) (PEDOT:PSS (50 nm)/polyvinyl carbazole (PVK):[zinc oxide (ZnO)] (50 nm)/[(Sm(III)]:[zinc(II) 2,3-tetrakis(dihydroxyphenyl)-porphyrin and Pt(II) 2,3-dimethoxyporphyrin] (60 nm)/2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) (15 nm)/Al (150 nm) have been fabricated and investigated. An electroplex occurring at the (PVK/Sm: Pt(II) 2,3-dimethoxyporphyrin) interface has been suggested when ZnO nanoparticles were doped in PVK. OLED studies have revealed that the photophysical characteristics and electrical behavior of devices with ZnO nanoparticles are much better than those of devices with pure PVK. The efficiency of devices based on [(Sm(III)] was superior than that of known aluminum tris(8-hydroxyquinoline) (Alq3) and also our earlier reports on red OLEDs under the same conditions.

Assessment of semen function and lipid peroxidation among lead exposed men

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kasperczyk, Aleksandra; Kasperczyk, Slawomir; Horak, Stanislaw

The study population included healthy, fertile men, employees of Zinc and Lead Metalworks (n = 63). Workers exposed to lead were divided into two groups: a group with moderate exposure to lead (ME) - blood lead level (PbB) 25-40 {mu}g/dl and a group with high exposure to lead (HE) PbB = 40-81 {mu}g/dl. The control group consisted of office workers with no history of occupational exposure to lead. Evaluation of lead, cadmium and zinc level in blood and seminal plasma, zinc protoporphyrin in blood (ZPP), 5-aminolevulinic acid in urine (ALA), malondialdehyde (MDA) in seminal plasma and sperm analysis were performed.more » No differences were noted in the concentration of cadmium and zinc in blood and seminal plasma in the study population. Lipid peroxidation in seminal plasma, represented as MDA concentration, significantly increased by about 56% in the HE group and the percentage of motile sperm cells after 1 h decreased by about 34% in comparison to the control group. No statistically significant correlation between other parameters of sperm analysis and lead exposure parameters nor between lead, cadmium and zinc concentration in blood and seminal plasma were found. A positive association between lead intoxication parameters (PbB, ZPP, lead seminal plasma) and MDA concentration in sperm plasma and inverse correlation with sperm cells motility (PbB, ZPP) was found. An increased concentration of MDA was accompanied by a drop in sperm cells motility. In conclusion, we report that high exposure to lead causes a decrease of sperm motility in men most likely as a result of increased lipid peroxidation, especially if the level in the blood surpasses the concentration of 40 {mu}g/dl.« less

Recent trends and current practices for secondary processing of zinc and lead. Part II: zinc recovery from secondary sources.

PubMed

Sahu, Kamala Kanta; Agrawal, Archana; Pandey, Banshi Dhar

2004-08-01

Almost all metallurgical processes are associated with the generation of wastes and residues that may be hazardous or non-hazardous in nature depending upon the criteria specified by institutions such as the US Environment Protection Agency, etc. Wastes containing heavy and toxic metals such as arsenic, cadmium, chromium, nickel, lead, copper, mercury, zinc, etc., that are present beyond permissible limits deemed to be treated or disposed of, and non-hazardous wastes can be utilized for metal recovery or safe disposal. Zinc is in growing demand all over the world. In India, a major amount of zinc is imported and therefore processing of zinc secondaries will assist in satisfying the gap between demand and supply to some extent. This report mainly focuses on the current practices and recent trends on the secondary processing of zinc. Attempts made by various laboratories to develop ecofriendly processes for the recovery of zinc from secondary raw materials are also described and discussed.

Comprehensive monitoring of drinking well water quality in Seoul metropolitan city, Korea.

PubMed

Kim, Ki-Hyun; Susaya, Janice P; Park, Chan Goo; Uhm, Jung-Hoon; Hur, Jin

2013-08-01

In this research, the quality of drinking well waters from 14 districts around Seoul metropolitan city, Korea was assessed by measuring a number of parameters with established guideline (e.g., arsenic, fluoride, nitrate nitrogen, benzene, 1,2-dichloroethene, dichloromethane, copper, and lead) and without such criteria (e.g., hardness, chloride ion, sulfate ion, ammonia nitrogen, aluminum, iron, manganese, and zinc). Physical parameters such as evaporation residue (or total dissolved solids) and turbidity were also measured. The importance of each parameter in well waters was examined in terms of the magnitude and exceedance frequency of guideline values established by international (and national) health agencies. The results of this study indicate that among the eight parameters with well-established guidelines (e.g., WHO), arsenic and lead (guideline value of 0.01 mg L(-1) for both) recorded the highest exceedance frequency of 18 and 16 well samples ranging in 0.06-136 and 2-9 mg L(-1), respectively. As such, a number of water quality parameters measured from many well waters in this urban area were in critical levels which require immediate attention for treatment and continuous monitoring.

[The morphofunctional state of the bone marrow in lead and zinc intoxication].

PubMed

Vladimtseva, T M; Pashkevich, I A; Salmina, A B

2006-01-01

The nucleolus is a compulsory nuclear structure of all cells of eukaryotes. The quantitative and qualitative characteristics of nuclei show the functional activity of a cell, the rate of its synthesis of RNA and portents, and its metabolic state. Heavy metals (zinc chloride and lead acetate) were comparatively investigated for their effects on the nucleolar apparatus of bone marrow cells in in vivo experiments. Zinc chloride and lead acetate were ascertained to damage the nucleolar apparatus of cells, thus decreasing their transcriptional activity or irreversibly damaging them.

Lead and zinc intoxication in companion birds.

PubMed

Puschner, Birgit; Poppenga, Robert H

2009-01-01

Although the toxicity of lead and zinc to birds is widely recognized by veterinarians and bird owners, these metals are frequently found in the environments of pet and aviary birds, and intoxications are common. Clinical signs exhibited by intoxicated birds are often nonspecific, which makes early diagnosis difficult. Fortunately, lead and zinc analyses of whole blood and serum or plasma, respectively, are readily available and inexpensive; elevated concentrations can confirm intoxication. Once diagnosed, intoxication can be effectively treated by (1) preventing further exposure, (2) administering chelating drugs, and (3) providing symptomatic and supportive care.

Research keeps lead and zinc viable in high-tech markets

NASA Astrophysics Data System (ADS)

Cole, Jerome F.

1989-08-01

Lead and zinc have long enjoyed widespread use in a variety of applications. To insure growing markets for the future, however, new applications for these durable metals must be developed. Currently, projects are underway to determine the capabilities of lead for such high-technology uses as earthquake damping and nuclear waste containment. Zinc's capabilities are being developed further, too, particularly in the areas of direct injection die casting, composites and the improvement of coating properties. Other ongoing research initiatives are attempting to better determine the health and environmental influences of these metals.

Organic-Free, ZnO-Assisted Synthesis of Zeolite FAU with Tunable SiO2 /Al2 O3 Molar Ratio.

PubMed

Guo, Ya; Sun, Tianjun; Gu, Yiming; Liu, Xiaowei; Ke, Quanli; Wang, Shudong

2018-05-04

Zeolite FAU with tunable SiO 2 /Al 2 O 3 molar ratio has been successfully synthesized in the absence of organic structure-directing agents (OSDA). Specifically, the addition of zinc species contributes to the feasible and effective adjustment of the framework SiO 2 /Al 2 O 3 molar ratio between about 4 and 6 depending on the amount of zinc species added in the batch composition. In contrast, a typical OSDA such as tetramethylammonium hydroxide (TMAOH) has a limited effect on the SiO 2 /Al 2 O 3 molar ratio of the zeolite. The role of zinc species is essential for the crystallization of zeolite FAU with a higher SiO 2 /Al 2 O 3 molar ratio under the particular synthesis conditions. It is speculated that zinc species may suppress the incorporation of aluminum into the aluminosilicate framework, which is due to the Coulombic repulsive interaction. A higher SiO 2 /Al 2 O 3 molar ratio is also found to be accompanied by a lower CO 2 adsorption heat for CO 2 /CH 4 separation. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Questa baseline and pre-mining ground-water quality investigation. 12. Geochemical and reactive-transport modeling based on tracer injection-synoptic sampling studies for the Red River, New Mexico, 2001-2002

USGS Publications Warehouse

Ball, James W.; Runkel, Robert L.; Nordstrom, D. Kirk

2005-01-01

Reactive-transport processes in the Red River, downstream from the town of Red River in north-central New Mexico, were simulated using the OTEQ reactive-transport model. The simulations were calibrated using physical and chemical data from synoptic studies conducted during low-flow conditions in August 2001 and during March/April 2002. Discharge over the 20-km reach from the town of Red River to the USGS streamflow-gaging station near the town of Questa ranged from 395 to 1,180 L/s during the 2001 tracer and from 234 to 421 L/s during the 2002 tracer. The pH of the Red River ranged from 7.4 to 8.5 during the 2001 tracer and from 7.1 to 8.7 during the 2002 tracer, and seep and tributary samples had pH values of 2.8 to 9.0 during the 2001 tracer and 3.8 to 7.2 during the 2002 tracer. Mass-loading calculations allowed identification of several specific locations where elevated concentrations of potential contaminants entered the Red River . These locations, characterized by features on the north side of the Red River that are known to be sources of low-pH water containing elevated metal and sulfate concentrations, are: the initial 2.4 km of the study reach, including Bitter Creek, the stream section from 6.2 to 7.8 km, encompassing La Bobita well and the Hansen debris fan, Sulphur Gulch, at about 10.5 km, the area near Portal Springs, from 12.2 to 12.6 km, and the largest contributors of mass loading, the 13.7 to 13.9 km stream section near Cabin Springs and the 14.7 to 17.5 km stream section from Shaft Spring to Thunder Bridge, Goathill Gulch, and Capulin Canyon. Speciation and saturation index calculations indicated that although solubility limits the concentration of aluminum above pH 5.0, at pH values above 7 and aluminum concentrations below 0.3 mg/L inorganic speciation and mineral solubility controls no longer dominate and aluminum-organic complexing may occur. The August 2001 reactive-transport simulations included dissolved iron(II) oxidation, constrained using measured concentrations of dissolved iron(II) and dissolved iron(total). Both simulations included precipitation of amorphous Al(OH)3 and hydrous ferric oxide as Fe(OH)3, and sorption of copper and zinc to the precipitated hydrous ferric oxide. Simulations revealed that hydrogen, iron, aluminum, copper, and zinc were non-conservative and that mineral precipitation can account for iron and aluminum concentrations. Copper and zinc concentrations can be accounted for by simulating their sorption to hydrous ferric oxide forming in the water column of the Red River , although hydrous manganese oxides also may be important sorption substrates.

Characterizing and simulation the scintillation properties of zinc oxide nanowires in AAO membrane for medical imaging applications

NASA Astrophysics Data System (ADS)

Esfandi, F.; Saramad, S.; Rezaei Shahmirzadi, M.

2017-07-01

In this work, a new method is proposed for extracting some X-ray detection properties of ZnO nanowires electrodeposited on Anodized Aluminum Oxide (AAO) nanoporous template. The results show that the detection efficiency for 12μm thickness of zinc oxide nano scintillator at an energy of 9.8 keV, near the K-edge of ZnO (9.65 keV), is 24%. The X-rays that interact with AAO can also generate electrons that reach the nano scintillator. The scintillation events of these electrons are seen as a low energy tail in the spectrum. In addition, it is found that all the X-rays that are absorbed in 300 nm thickness of the gold layer on the top of the zinc oxide nanowires can participate in the scintillation process with an efficiency of 6%. Hence, the scintillation detection efficiency of the whole detector for 9.8 keV X-ray energy is 30%. The simulation results from Geant4 and the experimental detected photons per MeV energy deposition are also used to extract the light yield of the zinc oxide nano scintillator. The results show that the light yield of the zinc oxide nanowires deposited by the electrochemical method is approximately the same as for single crystal zinc oxide scintillator (9000). Much better spatial resolution of this nano scintillator in comparison to the bulk ones is an advantage which candidates this nano scintillator for medical imaging applications.

Particles and Zinc on the Absorbed Impact Energy of Gravity Cast Aluminum Matrix Composites

NASA Astrophysics Data System (ADS)

Corchado, Marcos; Reyes, Fernando; Suárez, Oscar Marcelo

2014-06-01

The effect of different amounts of boron, in the form of AlB2 particles, as well as zinc concentration in a gravity cast Al-B-Zn composite, was studied and related to the absorbed energy upon fracture during Charpy impact experiments. In addition, the authors correlated the composite Brinell hardness with the quantitative assessment of brittle and ductile fracture areas of the Charpy fractured specimens and found that increasing AlB2 particle concentration resulted in a reduction of absorbed impact energy. Although larger zinc levels produced somewhat similar results, the AlB2 effect was prevalent. The energy absorption upon impact reached a maximum when no particles were present; conversely, the lowest amount of absorbed energy corresponded to a composite with a composition of 15 wt.% Zn and 8% in volume of AlB2, i.e., the highest concentration of AlB2 and zinc studied. Raising the amount of AlB2 as well as zinc, as expected, resulted in higher Brinell hardness. A statistical analysis allowed studying of the particle size distribution, whereas values for crack tip opening displacement were subsequently calculated for the range of particle sizes found and the corresponding AlB2 particle volume percent. Higher porosity values were measured for larger AlB2 volume percent. Finally, analyses of fracture surfaces corroborated that brittle fracture was favored in composites with higher amounts of AlB2 and zinc.

Zinc supplementation in children with cystic fibrosis

USDA-ARS?s Scientific Manuscript database

Cystic fibrosis (CF) leads to malabsorption of macro- and micronutrients. Symptomatic zinc deficiency has been reported in CF but little is known about zinc homeostasis in children with CF. Zinc supplementation (Zn suppl) is increasingly common in children with CF but it is not without theoretcial r...

Mechanical Rope and Cable

DTIC Science & Technology

1975-04-01

seawater. The principal effect of crevices on the corrosion of zinc- or aluminum - coated or uncoated steel rope is to entrap corrosive liquids and...visual inspection of the rope surface. j 5. The effect of stresses, such as tensile, bending, torsion , and comn- pression, upon rope in service is not...questionable A value. d. The effect of stresses, such as tensile, bending, torsion , and compressive contact, on rope is not understood well. 2

Maskless Nanoscale Writing of Nanoparticle-Polymer Composites and Nanoparticle Assemblies using Thermal Nanoprobes

DTIC Science & Technology

2009-09-14

the otherwise difficult to deposit Alq3 using a p(VDF-TrFE) carrier. The Alq3 retains its ability to fluoresce after deposition. (h) SEM of the...aluminum tris(8-hydroxyquinoline) ( Alq3 ) ∼0.9 P(VDF-TrFE) 1 zinc diethyldithiocarbamate ∼1.2 P(VDF-TrFE) 1 CdSe-ZnS core-shell 2-4 PE 1 dodecanethiol

Air Force Successes and Challenges in Cr(VI) Elimination

DTIC Science & Technology

2011-05-10

ion vapor deposited Al, and Cd coatings 2. Use trivalent chromium [Cr(III)] conversion coating (CC) on Dipsol IZ- C17+ zinc-nickel (Zn-Ni) coating...interested in results Anodized T-38 aileron levers 10 Chromium -Free Conversion Coatings  Identify and evaluate chromium -free conversion coatings (CFCCs...the chromium -based conversion coating for treatment of aluminum alloys at OC-ALC • Conduct technology assessment to identify suitable Cr-free

REFRACTORY DIE FOR EXTRUDING URANIUM

DOEpatents

Creutz, E.C.

1959-08-11

A die is presented for the extrusion of metals, said die being formed of a refractory complex oxide having the composition M/sub n/O/sub m/R/sub x/O/sub y/ where M is magnesium, zinc, manganese, or iron, R is aluminum, chromic chromium, ferric iron, or manganic manganese, and m, n, x, and y are whole numbers. Specific examples are spinel, magnesium aluminate, magnetite, magnesioferrite, chromite, and franklinite.

Atomic absorption spectrometric determination of copper, zinc, and lead in geological materials

USGS Publications Warehouse

Sanzolone, R.F.; Chao, T.T.

1976-01-01

An atomic absorption spectrometric method is described for the determination of copper, zinc, and lead in geological materials. The sample is digested with HF-HCl-H2O2; the final solution for analysis is in 10 % (v/v) HCl. Copper and zinc are determined directly by aspirating the solution into an air-acetylene flame. A separate aliquot of the solution is used for determination of lead; lead is extracted into TOPO-MIBK from the acidic solution in the presence of iodide and ascorbic acid. For a 0.50-g sample, the limits of determination are 10-2000 p.p.m. for Cu and Zn, and 5-5000 p.p.m. for Pb. As much as 40 % Fe or Ca. and 10 % Al, Mg, or Mn in the sample do not interfere. The proposed method can be applied to the determination of copper, zinc, and lead in a wide range of geological materials including iron- and manganese-rich, calcareous and carbonate samples. ?? 1976.

Dust Explosion Characteristics of Aluminum, Titanium, Zinc, and Iron-Based Alloy Powders Used in Cold Spray Processing

NASA Astrophysics Data System (ADS)

Sakata, K.; Tagomori, K.; Sugiyama, N.; Sasaki, S.; Shinya, Y.; Nanbu, T.; Kawashita, Y.; Narita, I.; Kuwatori, K.; Ikeda, T.; Hara, R.; Miyahara, H.

2014-01-01

Compared to conventional thermal spray coating, cold spray processing typically employs finer, smaller-diameter metal powders. Furthermore, cold-sprayed particles exhibit fewer surface oxides than thermally sprayed particles due to the absence of particle melting during spraying. For these reasons, it is important to consider the potential for dust explosions or fires during cold spray processing, for both industrial and R&D applications. This work examined the dust explosion characteristics of metal powders typically used in cold spray coating, for the purpose of preventing dust explosions and fires and thus protecting the health and safety of workers and guarding against property damage. In order to safely make use of the new cold spray technology in industrial settings, it is necessary to manage the risks based on an appropriate assessment of the hazards. However, there have been few research reports focused on such risk management. Therefore, in this study, the dust explosion characteristics of aluminum, titanium, zinc, carbonyl iron, and eutectoid steel containing chromium at 4 wt.% (4 wt.% Cr-eutectoid steel) powders were evaluated according to the standard protocols JIS Z 8818, IEC61241-2-3(1994-09) section 3, and JIS Z 8817. This paper reports our results concerning the dust explosion properties of the above-mentioned metal powders.

Tribological Characteristics of Submicron SiC(p)-GR(p)/Zn-35Al-1Mg Composites in Semisolidification Casting process

NASA Astrophysics Data System (ADS)

Liu, S.; Fang, Z. W.; Li, L. X.

2018-05-01

Uniform SiC(p)-GR(p)/Zn-35Al-1Mg composites were prepared by powder pressing and semisolidification stirring-casting process by adding submicron silicon carbide and graphite reinforcement particles in an aluminum-zinc alloy matrix. Micro Vickers hardness and microstructures of the novel composites were studied, and their wear properties and wear temperature were measured for different load and friction conditions. The results show that silicon carbide and graphite particles homogeneously mix in the matrix, while contained silicon carbide particles improve the matrix hardness to 8.4%, graphite improves the matrix hardness to 16.8%, but two of them, combined, reduce the matrix hardness to 7.6%; the rate of temperature rise of the zinc-aluminum matrix alloy is the highest than the other three composites and is up to 48.5° C/s at 1.69MPa. At 0.56MPa and sliding 26.4km, the graphite composite anti-wear effect is optimal, while at 1.13MPa, the wear resistance of silicon carbide and graphite compound particles is the best; in the other case of only silicon carbide particles, the wear resistance is increased to 35% at 1.69MPa and 26.4km, and its anti-wear effects are excellent.

Testing piezoelectric sensors in a nuclear reactor environment

NASA Astrophysics Data System (ADS)

Reinhardt, Brian T.; Suprock, Andy; Tittmann, Bernhard

2017-02-01

Several Department of Energy Office of Nuclear Energy (DOE-NE) programs, such as the Fuel Cycle Research and Development (FCRD), Advanced Reactor Concepts (ARC), Light Water Reactor Sustainability, and Next Generation Nuclear Power Plants (NGNP), are investigating new fuels, materials, and inspection paradigms for advanced and existing reactors. A key objective of such programs is to understand the performance of these fuels and materials during irradiation. In DOE-NE's FCRD program, ultrasonic based technology was identified as a key approach that should be pursued to obtain the high-fidelity, high-accuracy data required to characterize the behavior and performance of new candidate fuels and structural materials during irradiation testing. The radiation, high temperatures, and pressure can limit the available tools and characterization methods. In this work piezoelectric transducers capable of making these measurements are developed. Specifically, three piezoelectric sensors (Bismuth Titanate, Aluminum Nitride, and Zinc Oxide) are tested in the Massachusetts Institute of Technology Research reactor to a fast neutron fluence of 8.65×1020 nf/cm2. It is demonstrated that Bismuth Titanate is capable of transduction up to 5 × 1020 nf/cm2, Zinc Oxide is capable of transduction up to at least 6.27 × 1020 nf/cm2, and Aluminum Nitride is capable of transduction up to at least 8.65 × 1020 nf/cm2.

Zinc Supplementation Alters Plasma Aluminum and Selenium Status of Patients Undergoing Dialysis: A Pilot Study

PubMed Central

Guo, Chih-Hung; Chen, Pei-Chung; Hsu, Guoo-Shyng W.; Wang, Chia-Liang

2013-01-01

End stage renal disease patients undergoing long-term dialysis are at risk for abnormal concentrations of certain essential and non-essential trace metals and high oxidative stress. We evaluated the effects of zinc (Zn) supplementation on plasma aluminum (Al) and selenium (Se) concentrations and oxidative stress in chronic dialysis patients. Zn-deficient patients receiving continuous ambulatory peritoneal dialysis or hemodialysis were divided into two groups according to plasma Al concentrations (HA group, Al > 50 μg/L; and MA group, Al > 30 to ≤ 50 μg/L). All patients received daily oral Zn supplements for two months. Age- and gender-matched healthy individuals did not receive Zn supplement. Clinical variables were assessed before, at one month, and after the supplementation period. Compared with healthy subjects, patients had significantly lower baseline plasma Se concentrations and higher oxidative stress status. After two-month Zn treatment, these patients had higher plasma Zn and Se concentrations, reduced plasma Al concentrations and oxidative stress. Furthermore, increased plasma Zn concentrations were related to the concentrations of Al, Se, oxidative product malondialdehyde (MDA), and antioxidant enzyme superoxide dismutase activities. In conclusion, Zn supplementation ameliorates abnormally high plasma Al concentrations and oxidative stress and improves Se status in long-term dialysis patients. PMID:23609777

Zinc-aluminum oxide solid solution nanosheets obtained by pyrolysis of layered double hydroxide as the photoanodes for dye-sensitized solar cells.

PubMed

Xu, Zhiyuan; Shi, Jingjing; Haroone, Muhammad Sohail; Chen, Wenpeng; Zheng, Shufang; Lu, Jun

2018-04-01

Due to the superiority of metal-doped ZnO compared to TiO 2 , the Zn-M (M = Al 3+ , Ga 3+ , Cr 3+ , Ti 4+ , Ce 4+ ) mixed metal oxide solid solutions have been extensively studied for photocatalytic and photovoltaic applications. In this work, a systematic research has proceeded for the preparation of a zinc-aluminum oxide semiconductor as a photoanode for the dye-sensitized solar cells (DSSCs) by a simple pyrolysis route with the Zn-Al layered double hydroxide (LDH) as a precursor. The Zn-Al oxide solid solution has been applied for DSSCs as an electron acceptor, which is used to study the influence of different Al content and sintering temperature on the device efficiency. Finally, the Zn-Al oxide solid solution with calcination temperature 600 °C and Al 27 at.% content exhibits the best performance. The photoelectric efficiency improved 100 times when the Al 3+ content decreased from 44 to 27 at.%. The Zn x Al y O solid solution show a reasonable efficiency as photoanode materials in DSSCs, with the best preliminary performance reported so far, and shows its potential application for the photovoltaic devices. Copyright © 2018 Elsevier Inc. All rights reserved.

Rapid Thermal Annealing for Solution Synthesis of Transparent Conducting Aluminum Zinc Oxide Thin Films

NASA Astrophysics Data System (ADS)

Ullah, Sana; De Matteis, Fabio; Davoli, Ivan

2017-11-01

Transparent conducting oxide films with optimized dopant molar ratio have been prepared with limited pre- and postdeposition annealing duration of 10 min. Multiple aluminum zinc oxide (AZO) layers were spin-coated on ordinary glass substrates. The predeposition consolidation temperature and dopant molar ratio were optimized for electrical conductivity and optical transparency. Next, a group of films were deposited on Corning glass substrates from precursor solutions with the optimized dopant ratio, followed by postdeposition rapid thermal annealing (RTA) at different temperatures and in controlled environments. The lowest resistivity of 10.1 × 10-3 Ω cm was obtained for films receiving RTA at 600°C for 10 min each in vacuum then in N2-5%H2 environment, while resistivity of 20.3 × 10-3 Ω cm was obtained for films subjected to RTA directly in N2-5%H2. Optical measurements revealed average total transmittance of about 85% in the visible region. A direct allowed transition bandgap was determined based on the absorption edge with a value slightly above 3.0 eV, within the typical range for semiconductors. RTA resulted in desorption of oxygen with enhanced carrier concentration and crystallinity, which increased the carrier mobility with decreased bulk resistivity while maintaining the required optical transparency.