Preparation and characterization of zinc sulphide nanocomposites based on acrylonitrile butadiene rubber

NASA Astrophysics Data System (ADS)

Ramesan, M. T.; Nihmath, A.; Francis, Joseph

2013-06-01

Rubber composite based on acrylonitrile butadiene rubber (NBR) reinforced with nano zinc sulphide (ZnS) have been prepared via vulcanization process and characterized by several techniques. Processing characteristics such as scorch time, optimum cure time decreases with increase in concentration of nano filler in acrylonitrile butadiene rubber. Mechanical properties such as tensile and tear strength increases with increase in concentration of nano filler up to 7 phr of loading thereafter the value decreases, whereas hardness, and flame resistance increases with the dosage of fillers. These enhanced properties are due to the homogenous dispersion of nano fillers in NBR matrix, which is evidenced from the structure that evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM).

Novel materials as potential infrared laser hosts

NASA Astrophysics Data System (ADS)

Sarkies, Julian Richard

The work presented in this thesis has concentrated on an assessment and characterisation of potential laser host media which will only support low phonon or vibrational modes. This is a necessary criterion if systems in which the active ions are lanthanides are to be made to lase in the mid-infrared, as in conventional host media non- radiative processes dominate transitions in this region. Research has concentrated upon two main areas. Firstly a spectroscopic study of lanthanide doped PBr3/AlBr3/SbBr3 was undertaken. A detailed investigation and characterisation of the stable solution formation region was carried out. The doping levels achievable were seen to vary across the lanthanide series from a maximum 0.24mol% for praesodymium to a minimum 0.15mol% for ytterbium. Energies of the characteristic 4 f absorptions of the trivalent lanthanides were measured, along with their oscillator strengths. Judd-Ofelt parameters were found for several rare earths. Stimulated emission cross sections were found to be higher than in conventional glass hosts for certain transitions, such as 6.83 × 10 -20 cm2 for the 4F3/2 --> 4I11/2 transition in the Nd3+ doped liquid. This was verified both experimentally and by the Ladenburg-Fuchtbauer relation when compared to a standard silicate glass. The behaviour, both spectroscopic and physical, of the doped solutions was seen to change dramatically upon heating. Heating the solutions gave rise to higher crystallisation rates, but lower non-radiative relaxation rates. Waveguide and laser experiments were attempted in both bulk and capillary geometries, however material factors such as crystallisation and thermal lensing prevented laser action. Secondly, rare earth doped planar waveguides of zinc sulphide were prepared. A full characterisation of the way in which waveguide loss was affected by factors such as deposition rate, doping level and waveguide masking during evaporation was performed. Waveguide losses as low as 1.5dB/cm at 980nm were measured. The loss was seen to have a strong λ-4 dependence, indicating it was predominantly due to Rayleigh scattering. Deposition onto heated substrates and post deposition annealing increased the loss significantly. Shielding the substrate from the radiant heating of the evaporation boat by partial masking of the substrate reduced the loss significantly. Doping the films caused a large increase in the loss for dopant concentrations of above 0.8mol%. Emission was observed from both Er3+ and Nd 3+ doped waveguides, and fluorescent lifetimes measured. The emission cross sections were measured for the 4F3/2 --> 4I11/2 transition in the Nd3+ doped waveguide, and for the 4I13/2 --> 4I 15/2 transition in the Er3+ doped waveguide. Multilayer dielectric mirrors were deposited onto the ends of a Nd3+ doped waveguide, forming a fully integrated resonator. The low damage threshold of the multilayer coatings precluded laser action. These results are believed to be the first ever reported for thermally evaporated doped zinc sulphide waveguides. This system has shown considerable promise as an infrared laser host, the future implications of this work are discussed and possible directions for future research suggested.

Investigation of element distributions in Luna-16 regolith

NASA Astrophysics Data System (ADS)

Kuznetsov, R. A.; Lure, B. G.; Minevich, V. Ia.; Stiuf, V. I.; Pankratov, V. B.

1981-03-01

The concentrations of 32 elements in fractions of different grain sizes in the samples of the lunar regolith brought back by Luna-16 are determined by means of neutron activation analysis. Four groups of elements are distinguished on the basis of the variations of their concentration with grain size, and concentration variations of the various elements with sample depth are also noted. Chemical leaching of the samples combined with neutron activation also reveals differences in element concentrations in the water soluble, metallic, sulphide, phosphate, rare mineral and rock phases of the samples. In particular, the rare earth elements are observed to be depleted in the regolith with respect to chondritic values, and to be concentrated in the phase extracted with 14 M HNO3.

Ferrous Analysis.

ERIC Educational Resources Information Center

Straub, William A.

1989-01-01

Elements covered in this review include: aluminum, antimony, arsenic, bismuth, boron, calcium, carbon, chromium, cobalt, copper, hydrogen, iron, lead, magnesium, manganese, molybdenum, nickel, niobium, nitrogen, oxygen, phosphorus, platinum, rare earths, silicons, sulfur, tin, titanium, tungsten, vanadium, zinc, and zirconium. Analytical methods…

Structure-property-composition relationships in doped zinc oxides: enhanced photocatalytic activity with rare earth dopants.

PubMed

Goodall, Josephine B M; Illsley, Derek; Lines, Robert; Makwana, Neel M; Darr, Jawwad A

2015-02-09

In this paper, we demonstrate the use of continuous hydrothermal flow synthesis (CHFS) technology to rapidly produce a library of 56 crystalline (doped) zinc oxide nanopowders and two undoped samples, each with different particle properties. Each sample was produced in series from the mixing of an aqueous stream of basic zinc nitrate (and dopant ion or modifier) solution with a flow of superheated water (at 450 °C and 24.1 MPa), whereupon a crystalline nanoparticle slurry was rapidly formed. Each composition was collected in series, cleaned, freeze-dried, and then characterized using analytical methods, including powder X-ray diffraction, transmission electron microscopy, Brunauer-Emmett-Teller surface area measurement, X-ray photoelectron spectroscopy, and UV-vis spectrophotometry. Photocatalytic activity of the samples toward the decolorization of methylene blue dye was assessed, and the results revealed that transition metal dopants tended to reduce the photoactivity while rare earth ions, in general, increased the photocatalytic activity. In general, low dopant concentrations were more beneficial to having greater photodecolorization in all cases.

Effect of aluminum and yttrium doping on zinc sulphide nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Swati, E-mail: sharma.swati1507@gmail.com; Kashyap, Jyoti; Kapoor, A.

2016-05-06

In this work, pristine and doped Zinc Sulphide (ZnS) nanoparticles have been synthesized via chemical co-precipitation method. ZnS nanoparticles have been doped with Aluminium (Al) and Yttrium (Y) with doping concentration of 5wt% each. The structural and optical properties of the as prepared nanoparticles have been studied using X-Ray diffraction (XRD) technique and Photoluminescence spectroscopy. Average grain size of 2-3nm is observed through the XRD analysis. Effect of doping on stress, strain and lattice constant of the nanoparticles has also been analyzed. Photoluminescence spectra of the as prepared nanoparticles is enhanced due to Al doping and quenched due to Ymore » doping. EDAX studies confirm the relative doping percentage to be 3.47 % and 3.94% by wt. for Al and Y doped nanoparticles respectively. Morphology of the nanoparticles studied using TEM and SEM indicates uniform distribution of spherical nanoparticles.« less

Progression in structural, magnetic and electrical properties of La-doped group IV elements

NASA Astrophysics Data System (ADS)

Deepapriya, S.; Annie Vinosha, P.; Rodney, John D.; Jerome Das, S.

2018-04-01

Progression of group IV elements such as zinc ferrite (ZnFe2O4), cobalt ferrite (CoFe2O4) was synthesized by doping lanthanum (La), via adopting a facile co-precipitation method. Doping hefty rare earth ion in spinel structure can amend to the physical properties of the lattice, which can be used in the enhancement of magnetic and electrical properties of the as-synthesized nanomaterial, it is vital to metamorphose and optimize its micro structural and magnetic features. The structural properties of the samples was analysed by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), Transmission electron microscopy (TEM) and UV-visible spectral analysis (UV-vis) reveals the optical property and optical band gap. The magnetic properties were evaluated using a vibrating sample magnetometer (VSM), the presence of functional group was confirmed by FTIR. XRD analyses elucidates that the synthesized samples zinc and cobalt had a spinel structure. From TEM analyses the morphology and diameter of the particle was observed. The substituted rare earth ions in Zinc ferrite inhibit the grain growth of the materials in an efficient manner compared with that of the Cobalt ferrite.

Separation of rare earths from transition metals by liquid-liquid extraction from a molten salt hydrate to an ionic liquid phase.

PubMed

Rout, Alok; Binnemans, Koen

2014-02-28

The solvent extraction of trivalent rare-earth ions and their separation from divalent transition metal ions using molten salt hydrates as the feed phase and an undiluted fluorine-free ionic liquid as the extracting phase were investigated in detail. The extractant was tricaprylmethylammonium nitrate, [A336][NO3], and the hydrated melt was calcium nitrate tetrahydrate, Ca(NO3)2·4H2O. The extraction behavior of rare-earth ions was studied for solutions of individual elements, as well as for mixtures of rare earths in the hydrated melt. The influence of different extraction parameters was investigated: the initial metal loading in the feed phase, percentage of water in the feed solution, equilibration time, and the type of hydrated melt. The extraction of rare earths from Ca(NO3)2·4H2O was compared with extraction from CaCl2·4H2O by [A336][Cl] (Aliquat 336). The nitrate system was found to be the better one. The extraction and separation of rare earths from the transition metals nickel, cobalt and zinc were also investigated. Remarkably high separation factors of rare-earth ions over transition metal ions were observed for extraction from Ca(NO3)2·4H2O by the [A336][NO3] extracting phase. Furthermore, rare-earth ions could be separated efficiently from transition metal ions, even in melts with very high concentrations of transition metal ions. Rare-earth oxides could be directly dissolved in the Ca(NO3)2·4H2O phase in the presence of small amounts of Al(NO3)3·9H2O or concentrated nitric acid. The efficiency of extraction after dissolving the rare-earth oxides in the hydrated nitrate melt was identical to extraction from solutions with rare-earth nitrates dissolved in the molten phase. The stripping of the rare-earth ions from the loaded ionic liquid phase and the reuse of the recycled ionic liquid were also investigated in detail.

[Rare earth elements content in farmland soils and crops of the surrounding copper mining and smelting plant in Jiangxi province and evaluation of its ecological risk].

PubMed

Jin, Shu-Lan; Huang, Yi-Zong; Wang, Fei; Xu, Feng; Wang, Xiao-Ling; Gao, Zhu; Hu, Ying; Qiao Min; Li, Jin; Xiang, Meng

2015-03-01

Rare earth elements content in farmland soils and crops of the surrounding copper mining and smelting plant in Jiangxi province was studied. The results showed that copper mining and smelting could increase the content of rare earth elements in soils and crops. Rare earth elements content in farmland soils of the surrounding Yinshan Lead Zinc Copper Mine and Guixi Smelting Plant varied from 112.42 to 397.02 mg x kg(-1) and 48.81 to 250.06 mg x kg(-1), and the average content was 254.84 mg x kg(-1) and 144.21 mg x kg(-1), respectively. The average contents of rare earth elements in soils in these two areas were 1.21 times and 0.68 times of the background value in Jiangxi province, 1.36 times and 0.77 times of the domestic background value, 3.59 times and 2.03 times of the control samples, respectively. Rare earth elements content in 10 crops of the surrounding Guixi Smelting Plant varied from 0.35 to 2.87 mg x kg(-1). The contents of rare earth elements in the leaves of crops were higher than those in stem and root. The contents of rare earth elements in Tomato, lettuce leaves and radish leaves were respectively 2.87 mg x kg(-1), 1.58 mg x kg(-1) and 0.80 mg x kg(-1), which were well above the hygienic standard limit of rare earth elements in vegetables and fruits (0.70 mg x kg(-1)). According to the health risk assessment method recommended by America Environmental Protection Bureau (USEPA), we found that the residents' lifelong average daily intake of rare earth elements was 17.72 mg x (kg x d)(-1), lower than the critical value of rare earth elements damage to human health. The results suggested that people must pay attention to the impact of rare earth elements on the surrounding environment when they mine and smelt copper ore in Jiangxi.

Insoluble zinc, cupric and tin pyrophosphates inhibit the formation of volatile sulphur compounds.

PubMed

Jonski, G; Young, A; Wåler, S M; Rölla, G

2004-10-01

Oral malodour is mainly a result of the production of volatile sulphur compounds (VSC). The present study was concerned with investigating the anti-VSC effect of insoluble pyrophosphates (PP) of zinc, copper(II) and tin(II). The hypothesis to be tested was that the sulphide anions produced when VSC are solubilized in water have a higher affinity for the respective metal ions than the PP anion. The anti-VSC effects of insoluble PP were compared with the corresponding soluble metal salts using three in vitro methods: saliva putrefaction; dialysis of a suspension of PP and saliva against water; and analysis of water containing hydrogen sulphide and methyl mercaptan gases, and gases in the headspace. The levels of VSC were analysed by gas chromatography in the first and third methods, and released metal ions were analysed by atomic absorption spectroscopy in the second. The results showed that: the insoluble metal PP inhibited VSC formation in saliva by 99-100%; under dialysis, only minute amounts of metal ions are released from the combination of PP and saliva; and the PP lost their metal cations in water containing dissolved gases and inhibited VSC formation. Hence, the results support the experimental hypothesis. Sulphide ions are obviously very strong ligands for these metal ions.

A Cryogenic Magnetostrictive Actuator Using a Persistent High Temperature Superconducting Magnet. Part 1; Concept and Design

NASA Technical Reports Server (NTRS)

Horner, Garnett; Bromberg, Leslie; Teter, J. P.

2000-01-01

Cryogenic magnetostrictive materials, such as rare earth zinc crystals, offer high strains and high forces with minimally applied magnetic fields, making the material ideally suited for deformable optics applications. For cryogenic temperature applications the use of superconducting magnets offer the possibility of a persistent mode of operation, i.e., the magnetostrictive material will maintain a strain field without power. High temperature superconductors (HTS) are attractive options if the temperature of operation is higher than 10 degrees Kelvin (K) and below 77 K. However, HTS wires have constraints that limit the minimum radius of winding, and even if good wires can be produced, the technology for joining superconducting wires does not exist. In this paper, the design and capabilities of a rare earth zinc magnetostrictive actuator using bulk HTS is described. Bulk superconductors can be fabricated in the sizes required with excellent superconducting properties. Equivalent permanent magnets, made with this inexpensive material, are persistent, do not require a persistent switch as in HTS wires, and can be made very small. These devices are charged using a technique which is similar to the one used for charging permanent magnets, e.g., by driving them into saturation. A small normal conducting coil can be used for charging or discharging. Because of the magnetic field capability of the superconductor material, a very small amount of superconducting magnet material is needed to actuate the rare earth zinc. In this paper, several designs of actuators using YBCO and BSCCO 2212 superconducting materials are presented. Designs that include magnetic shielding to prevent interaction between adjacent actuators will also be described. Preliminary experimental results and comparison with theory for BSCCO 2212 with a magnetostrictive element will be discussed.

Effect of RE (Nd3+, Sm3+) oxide on structural, optical properties of Na2O-Li2O-ZnO-B2O3 glass system

NASA Astrophysics Data System (ADS)

Hivrekar, Mahesh M.; Bhoyar, D. N.; Mande, V. K.; Dhole, V. V.; Solunke, M. B.; Jadhav, K. M.

2018-05-01

Zinc borate glass activated with rare earth oxide (Nd2O3, Sm2O3) of Na2O-Li2O-ZnO-B2O3 quaternary system has been prepared successfully by melt quenching method. The nucleation and growth of RE oxide were controlled temperature range 950-1000° C and rapid cooling at room temperature. The physical, structural and optical properties were characterized by using X-ray diffraction (XRD), SEM, Ultraviolet-visible spectroscopy (UV-Vis). XRD and SEM studies confirmed the amorphous nature, surface morphology of prepared zinc borate glass. The physical parameters like density, molar volume, molar mass of Nd3+, Sm3+ doped borate glass are summarized in the present article. The optical absorption spectra along with tauc's plot are presented. The optical energy band gap increases due to the addition of rare earth oxide confirming the role of network modifier.

Improving the machinability of leaded free cutting steel through process optimization

NASA Astrophysics Data System (ADS)

Sathyamurthy, P.; Vetrivelmurugan, R.; Sooryaprakash, J.

2018-02-01

Free cutting steel grades are high sulphur grades which can be classified under two categories as Leaded and Non-Leaded. These grades are used for manufacturing components like Nuts, bolts, studs, hydraulic fittings, brake pistons where higher machining is required to get intricate shape. Machinability of these grades are affected by hard oxide inclusions and highly deformed manganese sulphide inclusions. At JSW, machinability of leaded free cutting steel is improved by various process modifications namely deoxidation through carbon and manganese, Tellurium (Rare earth element) addition and maintaining the oxygen level at 80- 120ppm. Former one avoids the formation of hard SiO2 and Al2O3 compounds, Tellurium addition forms PbTe compound at the tail of MnS inclusions which resists the deformation of MnS inclusions and increased oxygen level favours the formation of less deformable oxy- sulphide inclusions. Above process modifications have resulted in achieving the low silicate content, better aspect ratio of MnS inclusions in the final rolled product. They are assessed by the characteristics of chip formation and surface roughness of machined part.

Study of microstructure and electroluminescence of zinc sulfide thin film

NASA Astrophysics Data System (ADS)

Zhao-hong, Liu; Yu-jiang, Wang; Mou-zhi, Chen; Zhen-xiang, Chen; Shu-nong, Sun; Mei-chun, Huang

1998-03-01

The electroluminscent zinc sulfide thin film doped with erbium, fabricated by thermal evaporation with two boats, are examined. The surface and internal electronic states of ZnS thin film are measured by means of x-ray diffraction and x-ray photoemission spectroscopy. The information on the relations between electroluminescent characteristics and internal electronic states of the film is obtained. And the effects of the microstructure of thin film doped with rare earth erbium on electroluminescence are discussed as well.

Precambrian Sulphide Deposits

NASA Astrophysics Data System (ADS)

Doe, Bruce R.

1984-04-01

This book is dedicated to Howard S. Robinson, who was born and educated in the United States, but who spent his professional career in Canada with McIntyre Porcupine Mines, concentrating on Precambrian mineral deposits. Although his career in mineral exploration was distinguished, his major contribution to earth science was probably as one of the founders of the Geological Association of Canada, an institution to which he made a bequest in his will. With this background, the strong emphasis on Canadian Precambrian mineral deposits should come as no surprise; of the 23 papers in this book, 21 are solely or primarily devoted to Canadian deposits. The two exceptions—those describing the Balmat, N.Y., zinc mines (at times the largest zinc producer in the United States) and the Crandon, Wisconsin, volcanogenic zinc-copper massive-sulfide deposit (the largest deposit of its kind found in the 1970s)—are each within a couple of hundred kilometers of the Canadian border. Although the title of the book is more expansive than the actual topics discussed, Canada is rich in Precambrian rocks and ore bodies, and Canadian scientists have been especially alert to tectonic influences in the formation of mineral deposits. These features, plus the fact that the country contains a very well exposed expanse of Archean rocks which is the largest in the world, facilitate the study of early crustal evolution and make the book of particular interest to geophysicists.

The significance of the source of zinc and its anti-VSC effect.

PubMed

Rölla, G; Jonski, G; Young, A

2002-06-01

The anti-VSC (volatile sulphur compounds) effect of zinc is known to be associated with free zinc ions. To examine whether zinc salts with low stability constants were more suitable as sources of zinc in zinc lozenges than zinc salts with high stability constants. The former provide free zinc ions upon dissolution in water, whereas the latter provide few such ions. Identical lozenges were produced which contained either zinc acetate, zinc gluconate (low stability constants), zinc citrate or amino-acid chelated zinc (extremely high stability constants). All the lozenges contained 0.1 per cent of zinc. A test panel of 10 volunteers used the different lozenges randomly. VSC were measured by GC. The lozenge with the highest stability constant was as effective as those with very low stability constants. The anti-VSC effect was thus not related to this constant. These findings may be explained by the possibility that alternative ligands with stronger affinity for zinc than the original ligands in the lozenges may be present in the oral cavity. An in vitro experiment indicated that the sulphide ion (S2-) may be such a ligand.

Synthesis, characterization and photovoltaic performance of Mn-doped ZnS quantum dots- P3HT hybrid bulk heterojunction solar cells

NASA Astrophysics Data System (ADS)

Jabeen, Uzma; Adhikari, Tham; Shah, Syed Mujtaba; Pathak, Dinesh; Nunzi, Jean-Michel

2017-11-01

Zinc sulphide (ZnS) and transition metal-doped ZnS nanocrystals were synthesized by co-precipitation method. Further the synthesized nanocrystals were characterized by Field Emission Scanning Electron Microscope (FESEM), High Resolution Transmission Electron Microscope (HRTEM), Fluorescence, UV-Visible, X-ray diffraction (XRD) and Fourier Transformed Infra-red (FTIR) Spectrometer (FTIR). Scanning electron microscope supplemented with EDAX was employed to attain grain size and chemical composition of the nanomaterials. A considerable blue shift of absorption band was noted by the manganese concentration (0.5 M) in the doped sample in comparison with ZnS quantum dots because of the decrease in the size of nanoparticles which may be due to quantum confinement. The photoluminescence emission observed at 596 nm is due to the emission of divalent manganese and can be ascribed to a 4T1→6A1 transition within the 3d shell. Though, the broad blue emission band was observed at 424 nm which may originates from the radiative recombination comprising defect states in the un-doped zinc sulphide quantum dots. XRD analysis exhibited that the synthesized nanomaterial endured in cubic structure. The synthesized nanomaterial combined with organic polymer P3HT, poly (3-hexyl thiophene) and worked in the construction of inverted solar cells. The photovoltaic devices with un-doped zinc sulphide quantum dots showed power conversion efficiency of 0.48% without annealing and 0.52% with annealing. By doping with manganese, the efficiency was enhanced by a factor of 0.52 without annealing and 0.59 with annealing. The morphology and packing behavior of blend of nanocrystals with organic polymer were explored using Atomic Force Microscopy.

Rare earth doped zinc oxide varistors

DOEpatents

McMillan, A.D.; Modine, F.A.; Lauf, R.J.; Alim, M.A.; Mahan, G.D.; Bartkowiak, M.

1998-12-29

A varistor includes a Bi-free, essentially homogeneous sintered body of a ceramic composition including, expressed as nominal weight %, 0.2--4.0% oxide of at least one rare earth element, 0.5--4.0% Co{sub 3}O{sub 4}, 0.05--0.4% K{sub 2}O, 0.05--0.2% Cr{sub 2}O{sub 3}, 0--0.2% CaO, 0.00005--0.01% Al{sub 2}O{sub 3}, 0--2% MnO, 0--0.05% MgO, 0--0.5% TiO{sub 3}, 0--0.2% SnO{sub 2}, 0--0.02% B{sub 2}O{sub 3}, balance ZnO. 4 figs.

Rare earth doped zinc oxide varistors

DOEpatents

McMillan, April D.; Modine, Frank A.; Lauf, Robert J.; Alim, Mohammad A.; Mahan, Gerald D.; Bartkowiak, Miroslaw

1998-01-01

A varistor includes a Bi-free, essentially homogeneous sintered body of a ceramic composition including, expressed as nominal weight %, 0.2-4.0% oxide of at least one rare earth element, 0.5-4.0% Co.sub.3 O.sub.4, 0.05-0.4% K.sub.2 O, 0.05-0.2% Cr.sub.2 O.sub.3, 0-0.2% CaO, 0.00005-0.01% Al.sub.2 O.sub.3, 0-2% MnO, 0-0.05% MgO, 0-0.5% TiO.sub.3, 0-0.2% SnO.sub.2, 0-0.02% B.sub.2 O.sub.3, balance ZnO.

Unraveling Recrystallization Mechanisms Governing Texture Development from Rare Earth Element Additions to Magnesium

NASA Astrophysics Data System (ADS)

Imandoust, Aidin

The origin of texture components associated with rare-earth (RE) element additions in wrought magnesium (Mg) alloys is a long-standing problem in magnesium technology. The objective of this research is to identify the mechanisms accountable for rare-earth texture during dynamic recrystallization (DRX). Towards this end, we designed binary Mg-Cerium and Mg-Gadolinium alloys along with complex alloy compositions containing zinc, yttrium and Mischmetal. Binary alloys along with pure Mg were designed to individually investigate their effects on texture evolutions, while complex compositions are designed to develop randomized texture, and be used in automotive and aerospace applications. We selected indirect extrusion to thermo-mechanically process our materials. Different extrusion ratios and speeds were designed to produce partially and fully recrystallized microstructures, allowing us to analyze DRX from its early stages to completion. X-ray diffraction, electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM) were used to conduct microstructure and texture analyses. Our analyses revealed that rare-earth elements in zinc-containing magnesium alloys promote discontinuous dynamic recrystallization at the grain boundaries. During nucleation, the effect of rare earth elements on orientation selection was explained by the concomitant actions of multiple Taylor axes in the same grain. Isotropic grain growth was observed due to rare earth elements segregating to grain boundaries, which lead to texture randomization. The nucleation in binary Mg-RE alloys took place by continuous formation of necklace structures. Stochastic relaxation of basal and non-basal dislocations into low-angle grain boundaries produced chains of embryos with nearly random orientations. Schmid factor analysis showed a lower net activation of dislocations in RE textured grains compared to ones on the other side of the stereographic triangle. Lower dislocation densities within RE grains favored their growth by setting the boundary migration direction toward grains with higher dislocation density, thereby decreasing the system energy. We investigated the influence of RE elements on extension twinning induced hardening. RE addition enhanced tensile twinning induced hardening significantly. EBSD analysis illustrated that tensile twins cross low angle grain boundaries in Mg-RE alloys, which produced large twins and facilitated transmutation of basal to prismatic dislocations. Higher activity of pyramidal II dislocations in Mg-RE alloys resulted in higher twinning induced hardening.

White light generation via up-conversion and blue tone in Er3+/Tm3+/Yb3+-doped zinc-tellurite glasses

NASA Astrophysics Data System (ADS)

Rivera, V. A. G.; Ferri, F. A.; Nunes, L. A. O.; Marega, E.

2017-05-01

Yb3+, Er3+ and Tm3+ triply doped zinc-tellurite glass have been prepared containing up to 3.23 wt% of rare-earth ion oxides, were characterized by absorption spectroscopy, excitation, emission and up-conversion spectra. Transparent and homogeneous glasses have been produced, managing the red, green and blue emission bands, in order to generate white light considering the human eye perception. The energy transfer (resonant or non-resonant) between those rare-earth ions provides a color balancing mechanism that maintains the operating point in the white region, generating warm white light, cool white light and artificial daylight through the increase of the 976/980 nm diode laser excitation power from 4 to 470 mW. A light source at 4000 K is obtained under the excitation at 980 nm with 15 mW, providing a white light environment that is comfortable to the human eye vision. The spectroscopic study presented in this work describes the white light generation by the triply-doped zinc-tellurite glass, ranging from blue, green and red, by controlling the laser excitation power and wavelength at 976/980 nm. Such white tuning provokes healthy effects on human health throughout the day, especially the circadian system.

Effects of rare-earth doping on femtosecond laser waveguide writing in zinc polyphosphate glass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fletcher, Luke B.; Witcher, Jon J.; Troy, Neil

We have investigated waveguide writing in Er-Yb doped zinc polyphosphate glass using a femtosecond laser with a repetition rate of 1 KHz. We find that fabrication of good waveguides requires a glass composition with an O/P ratio of 3.25. The dependence on laser writing parameters including laser fluence, focusing conditions, and scan speed is reported. Waveguide properties together with absorption and emission data indicate that these glasses can be used for the fabrication of compact, high gain amplifying devices.

Influence of iron substitution by selected rare-earth ions on the properties of NiZn ferrite fillers and PVC magneto-polymer composites

NASA Astrophysics Data System (ADS)

Ušák, Elemír; Ušáková, Mariana; Dosoudil, Rastislav; Šoka, Martin; Dobročka, Edmund

2018-04-01

Nickel-zinc ferrites are very important soft magnetic materials from the point of view of diverse technical applications (such as, e.g., various electronic devices and components) for their high magnetic permeability and permittivity, low core loss, high resistivity, high Curie temperature as well as mechanical strength and chemical stability. Due to their good absorbing properties, they can be used as microwave absorbing and shielding materials with the aim of decreasing the environmental pollution caused by non-ionizing microwave radiation. The ferrite material incorporated into the polymer matrix creates qualitatively new magneto-polymer composite material taking benefits from both components. The properties typical for polymers (elasticity, mouldability, etc.) are combined with good high-frequency magnetic parameters, thus allowing to utilize these materials, e.g., in high-frequency applications where especially flexibility of composite materials plays a key role. Small amounts of selected rare-earth (RE) ions, in particular Y3+, La3+, Eu3+ and Gd3+ have been embedded into the nickel-zinc ferrite that has been used as the magnetic filler in magnetic polymer composites with polyvinylchloride (PVC) acting as the polymeric matrix. The effect of various types of rare-earth ions on the structural as well as quasi-static and dynamic (electro)magnetic properties of the ferrite fillers as well as ferrite/PVC composites, in particular the frequency dispersion of the complex permeability, has been studied.

The Earth's missing lead may not be in the core.

PubMed

Lagos, M; Ballhaus, C; Münker, C; Wohlgemuth-Ueberwasser, C; Berndt, J; Kuzmin, Dmitry V

2008-11-06

Relative to the CI chondrite class of meteorites (widely thought to be the 'building blocks' of the terrestrial planets), the Earth is depleted in volatile elements. For most elements this depletion is thought to be a solar nebular signature, as chondrites show depletions qualitatively similar to that of the Earth. On the other hand, as lead is a volatile element, some Pb may also have been lost after accretion. The unique (206)Pb/(204)Pb and (207)Pb/(204)Pb ratios of the Earth's mantle suggest that some lead was lost about 50 to 130 Myr after Solar System formation. This has commonly been explained by lead lost via the segregation of a sulphide melt to the Earth's core, which assumes that lead has an affinity towards sulphide. Some models, however, have reconciled the Earth's lead deficit with volatilization. Whichever model is preferred, the broad coincidence of U-Pb model ages with the age of the Moon suggests that lead loss may be related to the Moon-forming impact. Here we report partitioning experiments in metal-sulphide-silicate systems. We show that lead is neither siderophile nor chalcophile enough to explain the high U/Pb ratio of the Earth's mantle as being a result of lead pumping to the core. The Earth may have accreted from initially volatile-depleted material, some lead may have been lost to degassing following the Moon-forming giant impact, or a hidden reservoir exists in the deep mantle with lead isotope compositions complementary to upper-mantle values; it is unlikely though that the missing lead resides in the core.

Second Breakdown Susceptibility of Silicon-On-Sapphire Diodes having Systematically Different Geometries.

DTIC Science & Technology

1980-05-30

the collector material in- creased. Schafft and French 2 used zinc-cadmium sulphide phosphors to indi- cate the surface temperature distribution on...bathed in ultraviolet radiation from a mercury lamp. As the temperature of the phosphor is increased, the intensity of luminescence decreases and finally

Deformation, geochemistry, and origin of massive sulfide deposits, Gossan lead district, Virginia.

USGS Publications Warehouse

Gair, J.E.; Slack, J.F.

1984-01-01

Lenses and layers of massive sulphides comprise a discontinuous horizon in the late Proterozoic metasedimentary Ashe formation. The folded and brecciated sulphides include pyrrhotite, minor chalcopyrite, sphalerite and pyrite, and rare arsenopyrite and galena. The deposits were mined for supergene copper, later for gossan iron, and finally for sulphur. The Ashe formation is interpreted to be marine turbidites, and contains lenses of mafic rocks of probable tholeiitic basalt parentage. Mineralogically and chemically distinctive rocks - for the Ashe formation - are interbedded with the sulphides and may represent metamorphosed alteration zones and/or mixed chemical and clastic sediments. The sulphide deposits are interpreted as syngenetic sediments, modified by deformation during metamorphism. Their deposition occurred in a deep, elongate marine basin overlying a crustal rift zone.-G.J.N.

Isotopic links between atmospheric chemistry and the deep sulphur cycle on Mars.

PubMed

Franz, Heather B; Kim, Sang-Tae; Farquhar, James; Day, James M D; Economos, Rita C; McKeegan, Kevin D; Schmitt, Axel K; Irving, Anthony J; Hoek, Joost; Dottin, James

2014-04-17

The geochemistry of Martian meteorites provides a wealth of information about the solid planet and the surface and atmospheric processes that occurred on Mars. The degree to which Martian magmas may have assimilated crustal material, thus altering the geochemical signatures acquired from their mantle sources, is unclear. This issue features prominently in efforts to understand whether the source of light rare-earth elements in enriched shergottites lies in crustal material incorporated into melts or in mixing between enriched and depleted mantle reservoirs. Sulphur isotope systematics offer insight into some aspects of crustal assimilation. The presence of igneous sulphides in Martian meteorites with sulphur isotope signatures indicative of mass-independent fractionation suggests the assimilation of sulphur both during passage of magmas through the crust of Mars and at sites of emplacement. Here we report isotopic analyses of 40 Martian meteorites that represent more than half of the distinct known Martian meteorites, including 30 shergottites (28 plus 2 pairs, where pairs are separate fragments of a single meteorite), 8 nakhlites (5 plus 3 pairs), Allan Hills 84001 and Chassigny. Our data provide strong evidence that assimilation of sulphur into Martian magmas was a common occurrence throughout much of the planet's history. The signature of mass-independent fractionation observed also indicates that the atmospheric imprint of photochemical processing preserved in Martian meteoritic sulphide and sulphate is distinct from that observed in terrestrial analogues, suggesting fundamental differences between the dominant sulphur chemistry in the atmosphere of Mars and that in the atmosphere of Earth.

Structural, electronic, mechanical and magnetic properties of rare earth nitrides REN (RE= Pm, Eu and Yb)

NASA Astrophysics Data System (ADS)

Murugan, A.; Rajeswarapalanichamy, R.; Santhosh, M.; Iyakutti, K.

2015-07-01

The structural, electronic and mechanical properties of rare earth nitrides REN (RE=Pm, Eu and Yb) are investigated in NaCl and CsCl, and zinc blende structures using first principles calculations based on density functional theory. The calculated lattice parameters are in good agreement with the available results. Among the considered structures, these nitrides are most stable in NaCl structure. A pressure induced structural phase transition from NaCl to CsCl phase is observed in all these nitrides. The electronic structure reveals that these rare earth nitrides are half metallic at normal pressure. These nitrides are found to be covalent and ionic in the stable phase. The computed elastic constants indicate that these nitrides are mechanically stable and elastically anisotropic. Our results confirm that these nitrides are ferromagnetic in nature. A ferromagnetic to non-magnetic phase transition is observed at the pressures of 21.5 GPa and 46.1 GPa in PmN and YbN respectively.

A Cryogenic Magnetostrictive Actuator using a Persistent High Temperature Superconducting Magnet, Part 1: Concept and Design. Part 1; Concept and Design

NASA Technical Reports Server (NTRS)

Horner, Garnett C.; Bromberg, Leslie; Teter, J. P.

2001-01-01

Cryogenic magnetostrictive materials, such as rare earth zinc crystals, offer high strains and high forces with minimally applied magnetic fields, making the material ideally suited for deformable optics applications. For cryogenic temperature applications, such as Next Generation Space Telescope (NGST), the use of superconducting magnets offer the possibility of a persistent mode of operation, i.e., the magnetostrictive material will maintain a strain field without power. High temperature superconductors (HTS) are attractive options if the temperature of operation is higher than 10 degrees Kelvin (K) and below 77 K. However, HTS wires have constraints that limit the minimum radius of winding, and even if good wires can be produced, the technology for joining superconducting wires does not exist. In this paper, the design and capabilities of a rare earth zinc magnetostrictive actuator using bulk HTS is described. Bulk superconductors can be fabricated in the sizes required with excellent superconducting properties. Equivalent permanent magnets, made with this inexpensive material, are persistent, do not require a persistent switch as in HTS wires, and can be made very small. These devices are charged using a technique which is similar to the one used for charging permanent magnets, e.g., by driving them into saturation. A small normal conducting coil can be used for charging or discharging. Very fast charging and discharging of HTS tubes, as short as 100 microseconds, has been demonstrated. Because of the magnetic field capability of the superconductor material, a very small amount of superconducting magnet material is needed to actuate the rare earth zinc. In this paper, several designs of actuators using YBCO and BSCCO 2212 superconducting materials are presented. Designs that include magnetic shielding to prevent interaction between adjacent actuators will also be described. Preliminary experimental results and comparison with theory for BSSCO 2212 with a magnetostrictive element will be discussed.

Modern Projection of the Old Electroscope for Nuclear Radiation Quantitative Work and Demonstrations

ERIC Educational Resources Information Center

Bastos, Rodrigo Oliveira; Boch, Layara Baltokoski

2017-01-01

Although quantitative measurements in radioactivity teaching and research are only believed to be possible with high technology, early work in this area was fully accomplished with very simple apparatus such as zinc sulphide screens and electroscopes. This article presents an experimental practice using the electroscope, which is a very simple…

Sulphide-sulphate stability and melting in subducted sediment and its role in arc mantle redox and chalcophile cycling in space and time

NASA Astrophysics Data System (ADS)

Canil, Dante; Fellows, Steven A.

2017-07-01

The redox budget during subduction is tied to the evolution of oxygen and biogeochemical cycles on Earth's surface over time. The sulphide-sulphate couple in subducted crust has significant potential for redox and control on extraction of chalcophile metals from the arc mantle. We derive oxygen buffers for sulphide-sulphate stability ('SSO buffers') using mineral assemblages in subducted crust within the eclogite facies, and examine their disposition relative to the fO2 in the arc mantle along various P-T trajectories for subduction. The fO2 required for sulphide stability in subducted crust passing beneath an arc is shifted by variations in the bulk Ca/(Ca + Mg + Fe) of the subducting crust alone. Hotter slabs and more Fe-rich sediments stabilize sulphide and favour chalcophile sequestration deep into the mantle, whereas colder slabs and calcic sediment will stabilize anhydrite, in some cases at depths of melt generation in the arc mantle (<130 km). The released sulphate on melting potentially increases the fO2 of the arc mantle. We performed melting experiments on three subducted sediment compositions varying in bulk Ca/(Ca + Mg + Fe) from 0.3 to 0.6 at 2.5 GPa and 900-1100 °C to confirm how anhydrite stability can change by orders of magnitude the S, Cu, As, Zn, Mo, Pb, and Sb contents of sediment melts, and their subsequent liberation to the arc mantle. Using Cu/Sc as a proxy for the behaviour of S, the effect of variable subducted sediment composition on sulphide-sulphate stability and release of chalcophiles to the arc mantle is recognizable in volcanic suites from several subduction zones in space and time. The fO2 of the SSO buffers in subducted sediment relative to the arc mantle may have changed with time by shifts in the nature of pelagic sedimentation in the oceans over earth history. Oxidation of arc mantle and the proliferation of porphyry Cu deposits may be latter-day advents in earth history partly due to the rise of planktic calcifiers in the oceans in only the past 250 million years.

Topochemistry of trace metals in nasal mucosa. Potentialities of some histochemical methods and energy dispersive X-ray microanalysis.

PubMed

Torjussen, W; Haug, F M; Olsen, A; Andersen, I

1978-01-01

Histochemical methods and energy dispersive X-ray micro-analysis (EDX-analysis) were evaluated in model experiments and on tissue sections for their usefulness in detecting traces of metals in biological tissue. The goal for this study was to establish a method for localization of nickel deposits in the nasal mucosa, where it has been found in concentrations between 1 and 40 microgram/g in nickel exposed individuals. The histochemical methods tested were staining with dimethylglyoxime, rubeanic acid and dithizone, the Turnbull and Prussian blue methods and TIMM'S sulphide silver procedure. In model experiments nickel-, cobalt-, copper-, zinc- and ironsalts were applied to thin-layer chromatography sheets (TLC-sheets) and stained by the histochemical methods. Spots containing 500 and 50 ng of these metals represented the smallest amounts that could consistently be detected in these experiments, except for the sulphide silver method which seemed a little more sensitive. With the latter method, moreover, zinc was detected in 40 micrometer thick cryostat sections of gelatine made up with 1 microgram/g of the metal. For nickel the corresponding figure was 10 to 50 microgram/g. On specimens of nasal mucosa from nickel-exposed workers, a faint colour was obtained in 40 micron thick cryostat sections from specimens that had been immersed in dithizone, but the colour was too weak for histological analysis. None of the other coloured chelating agents caused noticeable staining when applied to blocks or to cryostat sections. TIMM'S sulphide silver method caused strong staining of the basal layers of the surface epithelium and of fibroblast-like cells in the underlying connective tissue. This staining pattern is described in more detail in a separate report. Rat liver tissue was analyzed by atomic absorption before and after araldite embedding. Blocks of gelatine made up with nickel, copper, zinc and iron were embedded in epoxy resin and analyzed by atomic absorption. Large changes in the metal concentrations, usually an increase, were found after embedding. Ultrathin sections from this material were used to test the sensitivity of the EDX-equipment. Referring to the concentrations determined by atomic absorption in the embedded material, iron was detected at 1215 microgram/g and 362 microgram/g (gelatine standards) but not at 167 microgram/g (rat liver). Similar values could not be determined for nickel, copper or zinc, because of background radiation resulting from the presence of these metals in the instrument. We did not succeed in establishing a procedure for detecting nickel deposits in nasal mucosa with any of the methods which were tested. The most sensitive but least specific of the tested methods for visualizing heavy metals in the nasal mucosa, was TIMM'S sulphide silver procedure. The preparation of tissue for this method is discussed.

How metallic is the binding state of indium hosted by excess-metal chalcogenides in ore deposits?

NASA Astrophysics Data System (ADS)

Ondina Figueiredo, Maria; Pena Silva, Teresa; Oliveira, Daniel; Rosa, Diogo

2010-05-01

Discovered in 1863, indium is nowadays a strategic scarce metal used both in classical technologic fields (like low melting-temperature alloys and solders) and in innovative nano-technologies to produce "high-tech devices" by means of new materials, namely liquid crystal displays (LCDs), organic light emitting diodes (OLEDs) and the recently introduced transparent flexible thin-films manufactured with ionic amorphous oxide semiconductors (IAOS). Indium is a typical chalcophile element, seldom forming specific minerals and occurring mainly dispersed within polymetallic sulphides, particularly with excess metal ions [1]. The average content of indium in the Earth's crust is very low but a further increase in its demand is still expected in the next years, thus focusing a special interest in uncovering new exploitation sites through promising polymetallic sulphide ores - e.g., the Iberian Pyrite Belt (IPB) [2] - and in improving recycling technologies. Indium recovery stands mostly on zinc extraction from sphalerite, the natural cubic sulphide which is the prototype of so-called "tetrahedral sulphides" where metal ions fill half of the available tetrahedral sites within the cubic closest packing of sulphur anions where the double of unfilled interstices are available for further in-filling. It is worth remarking that such packing array is particularly suitable for accommodating polymetallic cations by filling closely located interstitial sites [3] as happens in excess-metal tetrahedral sulphides - e.g. bornite, ideally Cu5FeS4, recognized as an In-carrying mineral [4]. Studying the tendency towards In-In interactions able of leading to the formation of polycations would efficiently contribute to understand indium crystal chemistry and the metal binding state in natural chalcogenides. Accordingly, an X-ray absorption near-edge spectroscopy (XANES) study at In L3-edge was undertaken using the instrumental set-up of ID21 beamline at the ESRF (European Synchrotron Radiation Facility, in Grenoble/France). Polymetallic chalcogenide minerals and various model compounds displaying distinct bonding situations of indium to other ligands (oxygen and halides) were studied. Encouraging results from a first experiment [5] showed the presence of a "white line" in the XANES spectra collected from InF3 and from In-hosting bornite; however, the impossibility of clearly identifying the nanoscale phase hosting indium in sulphide ore samples has hindered a full interpretation of X-ray absorption data. The crystal chemistry of indium in natural chalcogenides is now reanalysed and XANES results obtained so far for polymetallic sulphides are accordingly re-evaluated, disclosing a challenging clue for indium binding state in these host minerals within sulphide ores. [1] M.O. Figueiredo et al. (2007) Procd. 9th Biennial SGA Mtg., Dublin/Ireland, edt. C. Andrew et al., 1355-1357. [2] O.C. Gaspar (2002) Canad. Miner. 40, 611-636. [3] M.O. Figueiredo & T.P. Silva (2009) ICANS 23, 23rd Int. Conf. Amorphous & Nano-crystalline Semiconductors, Netherlands, August 23-28. Poster ID 229 (abstract). [4] T. Seifert & D. Sandmann (2002) Ore Geol. Reviews 28, 1-31. [5] M.O. Figueiredo & T.P. Silva (2009) XVIII Int. Mater. Res. Congr., Mexico, August 16-20. Symp. 20, Poster nr. 1 (abstract). * Work developed within the research project PTDC/CTE-GIN/67027/2006 financed by the Portuguese Foundation for Science & Technology (FCT/MCTES). The financial support from EU to perform the experiments at the ESRF is also acknowledged.

The carbonate-hosted willemite prospects of the Zambezi Metamorphic Belt (Zambia)

NASA Astrophysics Data System (ADS)

Boni, Maria; Terracciano, Rosario; Balassone, Giuseppina; Gleeson, Sarah A.; Matthews, Alexander

2011-10-01

Zambian willemite (Zn2SiO4) deposits occur in the metasedimentary carbonate rocks of the Proterozoic Katangan Supergroup. The most important orebodies are located around Kabwe and contain both sulphides and willemite in dolomites of low metamorphic grade. The Star Zinc and Excelsior prospects (Lusaka area), discovered in the early 1920s, occur in the metamorphic lithotypes of the late Proterozoic Zambezi Supracrustal sequence, which were deposited in a transtensional basin formed during the oblique collision of the Kalahari and Congo cratons. The deposits are hosted by the limestone and dolomitic marbles of the Cheta and Lusaka Formations. Structural analysis indicates that several fracture sets host the deposits, which may be genetically related to the Pan-African Mwembeshi dislocation zone (a major geotectonic boundary between the Lufilian Arc and the Zambezi Belt). In both prospects, willemite replaces the marbles and is found along joints and fissures with open-space filling textures and locally may develop colloform and vuggy fabrics as well. Silver as well as traces of germanium and cadmium have been detected within the willemite ore, and lead or zinc sulphides are scarce or absent. Calcite locally replaces willemite. Willemite is associated with specular hematite and franklinite and post-dates the Zn-spinel gahnite in the paragenesis. Genthelvite [Zn4Be3(SiO4)3S] occurs as a minor phase in irregular aggregates. The willemites from the Lusaka area, though Mn-poor, show green cathodoluminescence colours and bright green fluorescence in short-wave UV (as the high-temperature willemites in USA). Thermometric analyses of primary fluid inclusions in willemite yield homogenization temperatures that range from 160°C to 240°C and salinities of 8-16 wt.% equiv. NaCl. The homogenization temperatures suggest a hypogene-hydrothermal origin for the willemite concentrations. The geochemistry of fluid inclusion leachates suggests that the hydrothermal fluids were brines derived from highly evaporated seawater. Precise age constraints are currently lacking for the Lusaka area deposits, though the deposits are not deformed, indicating that they post-date the Lufilian orogeny (~520 Ma). The possibility of precursor ores exists; the gahnite-franklinite-willemite deposits could have been derived from a metamorphosed primary sulphide (or even nonsulphide) concentration that has subsequently been completely destroyed. However, there is no real evidence of such a primary source for the willemite mineral association. The Lusaka zinc ores may have been produced by an extensive hydrothermal system, with fluids discharging along basinal fracture zones controlled by the pre-Pan-African rifting stage. A paragenesis similar to that of the Lusaka prospects has been proposed to be a vector towards massive sulphide ores in several parts of the world; therefore, it is possible that these small willemite showings in Zambia may be part of a much bigger, and still unexplored, zinc province.

The thermal and chemical evolution of hydrothermal vent fluids in shale hosted massive sulphide (SHMS) systems from the MacMillan Pass district (Yukon, Canada)

NASA Astrophysics Data System (ADS)

Magnall, J. M.; Gleeson, S. A.; Blamey, N. J. F.; Paradis, S.; Luo, Y.

2016-11-01

At Macmillan Pass (YT, Canada), the hydrothermal vent complexes beneath two shale-hosted massive sulphide (SHMS) deposits (Tom, Jason) are well preserved within Late Devonian strata. These deposits provide a unique opportunity to constrain key geochemical parameters (temperature, salinity, pH, fO2, ΣS) that are critical for metal transport and deposition in SHMS systems, and to evaluate the interaction between hydrothermal fluids and the mudstone host rock. This has been achieved using a combination of detailed petrography, isotopic techniques (δ34S, δ13C and δ18O values), carbonate rare earth element analysis (LA-ICP-MS), fluid inclusion analysis (microthermometry, gas analysis via incremental crush fast scan mass spectrometry), and thermodynamic modelling. Two main paragenetic stages are preserved in both vent complexes: Stage 1 comprises pervasive ankerite alteration of the organic-rich mudstone host rock and crosscutting stockwork ankerite veining (±pyrobitumen, pyrite and quartz) and; Stage 2 consists of main stage massive sulphide (galena-pyrrhotite-pyrite ± chalcopyrite-sphalerite) and siderite (±quartz and barytocalcite) mineralisation. Co-variation of δ18O and δ13C values in ankerite can be described by temperature dependent fractionation and fluid rock interaction. Together with fluid inclusion microthermometry, this provides evidence of a steep thermal gradient (from 300 to ∼100 °C) over approximately 15 m stratigraphic depth, temporally and spatially constrained within the paragenesis of both vent complexes and developed under shallow lithostatic (<1 km; 250 bars) to hydrostatic (<400 m; 40 bars) conditions. There is evidence of mixing between diagenetic and hydrothermal fluids recorded in chondrite-normalised rare earth element (REE) profiles of ankerite and siderite. Middle REE enrichments and superchondritic Y/Ho ratios (>28), characteristic of diagenetic fluids, are coupled with positive europium anomalies and variable light REE depletion, which are more consistent with chloride complexation in hot (>250 °C) hydrothermal fluids. In this shallow sub-seafloor setting, thermal alteration of organic carbon in the immature, chemically reactive mudstones also had an important role in the evolution of fluid chemistry. Reduced sulphur generation via thermochemical reduction of Late Devonian seawater sulphate produced positive δ34S values in sulphide minerals (+7.5‰ to +19.5‰), coupled with a suite of volatile components (CO2, CH4, C1-C4 hydrocarbons, N2) trapped in Stage 2 quartz. Many of these geochemical features developed during the final stages of fluid ascent, in a system where the fluid cooled close to the site of mineralisation. Using this information, we have modelled the metal transporting capacity of the deep hydrothermal fluid, which even at modest salinities (6 wt.% NaCl) was high (≫100 ppm Pb, Zn), owing to the combined effects of high temperature and low pH (⩽4.5). Therefore in SHMS systems, enhanced geothermal gradients and rapid fluid ascent (with minimal fluid cooling) are considered to be the most important factors for transporting high concentrations of base metals to the site of mineralisation.

Internal structures and dating of non-sulphide Zn deposits using rock magnetism: insights from the Moroccan High Atlas

NASA Astrophysics Data System (ADS)

Charles, Nicolas; Choulet, Flavien; Sizaret, Stanislas; Chen, Yan; Barbanson, Luc; Ennaciri, Aomar; Badra, Lakhlifi; Branquet, Yannick

2016-01-01

The renewal of interest in Zn-Pb non-sulphide ores has been induced by mineral processing improvement and leads to new exploration and mining projects in the world. Although the mineralogy is often precisely known, and despite several studies linking ore deposition to regional tectonics, absolute dating of non-sulphide stages is rare and structure of ore bodies was largely disregarded. Geochronological data from non-sulphide ores are essential to timely constrain alteration episodes and to insert supergene ore genesis in the climate and tectonic evolution of the metallogenic province. The access to internal organization of ore could reveal post-mineralization episodes related to supergene evolution. Thus, a rock magnetism study combining anisotropy of magnetic susceptibility (AMS) and palaeomagnetism was performed on four non-sulphide deposits from the Moroccan High Atlas. AMS generally shows similar horizontal magnetic fabrics for ores and the clayey and carbonaceous internal sediments filling karstic cavities. The palaeomagnetic directions of ores and internal sediments are compatible, and the calculated poles are consistent with the last 30 Ma of the Africa apparent polar wander path, with an upper age at 0.78 Ma. The proposed three-step scenario is placed within the evolution of the Moroccan High Atlas belt. Deposition of primary sulphides is contemporaneous with opening of the Tethyan and Atlantic oceans. During the Tertiary, intracontinental deformation gave rise to the High Atlas fold-and-thrust belt and to regional uplift. Finally, Zn-Pb sulphides hosted in carbonates experienced oxidation under an arid climate to form karst-related Zn-Pb non-sulphide ores. These promising results pave the way for an efficient method to constrain the internal fabrics and age of Zn supergene deposits.

Thermoluminescence response of rare earth activated zinc lithium borate glass

NASA Astrophysics Data System (ADS)

Saidu, A.; Wagiran, H.; Saeed, M. A.; Obayes, H. K.; Bala, A.; Usman, F.

2018-03-01

New glasses of zinc lithium borate doped with terbium oxide were synthesized by high temperature solid-state reaction. The amorphous nature of the glasses was confirmed using x-ray diffraction analysis (XRD). Thermoluminescence (TL) response of pure zinc lithium borate (ZLB) and zinc lithium borate doped with terbium (ZLB: Tb) exposed to gamma radiation was measured and compared. There is significant enhancement in the TL yields of ZLB: Tb compared to that of pure ZLB. Effect of varying concentration of dopant (Tb4O7) on the TL response of zinc lithium borate was investigated. 0.3 mol% concentration of Tb exhibited strongest TL intensity. Thermoluminescence curve of the phosphor consist of single isolated peak. The TL response of the new materials to the exposed radiation is linear within 0.5-100 Gy range of dose with sublinearity at the lower region of the curve. High sensitivity was exhibited by the new amorphous materials. Reproducibility, thermal fading and energy response of the proposed TLD were investigated and shows remarkable result that made the phosphor suitable for radiation dosimetry.

Spent NiMH batteries-The role of selective precipitation in the recovery of valuable metals

NASA Astrophysics Data System (ADS)

Bertuol, Daniel Assumpção; Bernardes, Andréa Moura; Tenório, Jorge Alberto Soares

The production of electronic equipment, such as computers and cell phones, and, consequently, batteries, has increased dramatically. One of the types of batteries whose production and consumption has increased in recent times is the nickel metal hydride (NiMH) battery. This study evaluated a hydrometallurgical method of recovery of rare earths and a simple method to obtain a solution rich in Ni-Co from spent NiMH batteries. The active materials from both electrodes were manually removed from the accumulators and leached. Several acid and basic solutions for the recovery of rare earths were evaluated. Results showed that more than 98 wt.% of the rare earths were recovered as sulfate salts by dissolution with sulfuric acid, followed by selective precipitation at pH 1.2 using sodium hydroxide. The complete process, precipitation at pH 1.2 followed by precipitation at pH 7, removed about 100 wt.% of iron and 70 wt.% of zinc from the leaching solution. Results were similar to those found in studies that used solvent extraction. This method is easy, economic, and does not pose environmental threats of solvent extraction.

Studying microfungi-mineral interactions in sulphide-bearing waste-rock dumps: a 7 years survey in the Libiola mine, North-Eastern Italy

NASA Astrophysics Data System (ADS)

Marescotti, P.; Cecchi, G.; Di Piazza, S.; Lucchetti, G.; Zotti, M.

2015-12-01

Sulphide-bearing waste-rock dumps represent complex geological systems characterised by high percentages of low-grade mineralisations and non-valuable sulphides (such as pyrite and pyrrhotite). The sulphide oxidation triggers acid mine drainage (AMD) processes and the release of several metals of environmental concern. The severe physicochemical properties of these metal-contaminated environments tend to inhibit soil forming processes and represent an important stress factor for the biotic communities by exerting a strong selective pressure. Some macro- and micro-fungi are pioneer and extremophile organisms, which may survive and tolerate high concentrations of toxic metals in contaminated environments. Many studies show the fungal capability to bioaccumulate, biosorb, and store in their cells a high concentration of ecotoxic metals. A 7 years multidisciplinary survey was carried out in the Libiola sulphide mine. The results evidenced that the waste rock dumps of the area are characterized by an extremely poor flora and a specific mycobiota, due to the soil acidity, high concentration of trace metals, and unavailability or paucity of nutrients and organic matter. Our studies allowed the complete mineralogical, geochemical, and mycological characterization of one of the biggest dumps of the mine. 30 microfungal vital strains were isolated in pure cultures and studied with molecular and morphological approach, for their identification. The results allowed the isolation of some rare and important extremophilic species. Penicillium was the most recurrent genus, together with Trichoderma and Cladosporium. In particular, Penicillium glandicola is a rare species previously isolated from cave or arid environments, whereas P. brevicompactum is one of the most important fungi for metal corrosion. Hence, some bioaccumulation tests allowed to select a Trichoderma harzianum strain efficient to uptake Cu and Ag from pyrite-bearing soils, highlighting its central role in fungal remediation protocol. Further studies are in progress to investigate the potential interactions between microfungi and sulphides from the Libiola mine soils and to evaluate the fungal role in the biomineralisation and deactivation/mobilisation of toxic metals.

Notes on interpretation of geophysical data over areas of mineralization in Afghanistan

USGS Publications Warehouse

Drenth, Benjamin J.

2011-01-01

Afghanistan has the potential to contain substantial metallic mineral resources. Although valuable mineral deposits have been identified, much of the country's potential remains unknown. Geophysical surveys, particularly those conducted from airborne platforms, are a well-accepted and cost-effective method for obtaining information on the geological setting of a given area. This report summarizes interpretive findings from various geophysical surveys over selected mineral targets in Afghanistan, highlighting what existing data tell us. These interpretations are mainly qualitative in nature, because of the low resolution of available geophysical data. Geophysical data and simple interpretations are included for these six areas and deposit types: (1) Aynak: Sedimentary-hosted copper; (2) Zarkashan: Porphyry copper; (3) Kundalan: Porphyry copper; (4) Dusar Shaida: Volcanic-hosted massive sulphide; (5) Khanneshin: Carbonatite-hosted rare earth element; and (6) Chagai Hills: Porphyry copper.

Behaviour of Zinc Complexes and Zinc Sulphide Nanoparticles Revealed by Using Screen Printed Electrodes and Spectrometry

PubMed Central

Nejdl, Lukas; Ruttkay-Nedecky, Branislav; Kudr, Jiří; Kremplova, Monika; Cernei, Natalia; Prasek, Jan; Konecna, Marie; Hubalek, Jaromir; Zitka, Ondrej; Kynicky, Jindrich; Kopel, Pavel; Kizek, Rene; Adam, Vojtech

2013-01-01

In this study, we focused on microfluidic electrochemical analysis of zinc complexes (Zn(phen)(his)Cl2, Zn(his)Cl2) and ZnS quantum dots (QDs) using printed electrodes. This method was chosen due to the simple (easy to use) instrumentation and variable setting of flows. Reduction signals of zinc under the strictly defined and controlled conditions (pH, temperature, flow rate, accumulation time and applied potential) were studied. We showed that the increasing concentration of the complexes (Zn(phen)(his)Cl2, Zn(his)Cl2) led to a decrease in the electrochemical signal and a significant shift of the potential to more positive values. The most likely explanation of this result is that zinc is strongly bound in the complex and its distribution on the electrode is very limited. Changing the pH from 3.5 to 5.5 resulted in a significant intensification of the Zn(II) reduction signal. The complexes were also characterized by UV/VIS spectrophotometry, chromatography, and ESI-QTOF mass spectrometry. PMID:24233071

Boron isotope evidence for the involvement of non-marine evaporites in the origin of the Broken Hill ore deposits

USGS Publications Warehouse

Slack, J.F.; Palmer, M.R.; Stevens, B.P.J.

1989-01-01

IDENTIFYING the palaeogeographic setting and mode of origin of stratabound ore deposits can be difficult in high-grade metamorphic terranes, where the effects of metamorphism may obscure the nature of the protoliths. Here we report boron isotope data for tourmalines from the early Proterozoic Broken Hill block, in Australia, which hosts giant lead-zinc-silver sulphide deposits. With one exception the 11B/10B ratios are lower than those for all other tourmalines from massive sulphide deposits and tour-malinites elsewhere in the world. We propose that these low ratios reflect leaching of boron from non-marine evaporitic borates by convecting hydrothermal fluids associated with early Proterozoic continental rifting. A possible modern analogue is the Salton Sea geothermal field in California. ?? 1989 Nature Publishing Group.

Corrosion behaviour and biocorrosion of galvanized steel water distribution systems.

PubMed

Delaunois, F; Tosar, F; Vitry, V

2014-06-01

Galvanized steel tubes are a popular mean for water distribution systems but suffer from corrosion despite their zinc or zinc alloy coatings. First, the quality of hot-dip galvanized (HDG) coatings was studied. Their microstructure, defects, and common types of corrosion were observed. It was shown that many manufactured tubes do not reach European standard (NBN EN 10240), which is the cause of several corrosion problems. The average thickness of zinc layer was found at 41μm against 55μm prescribed by the European standard. However, lack of quality, together with the usual corrosion types known for HDG steel tubes was not sufficient to explain the high corrosion rate (reaching 20μm per year versus 10μm/y for common corrosion types). Electrochemical tests were also performed to understand the corrosion behaviours occurring in galvanized steel tubes. Results have shown that the limiting step was oxygen diffusion, favouring the growth of anaerobic bacteria in steel tubes. EDS analysis was carried out on corroded coatings and has shown the presence of sulphur inside deposits, suggesting the likely bacterial activity. Therefore biocorrosion effects have been investigated. Actually sulphate reducing bacteria (SRB) can reduce sulphate contained in water to hydrogen sulphide (H2S), causing the formation of metal sulphides. Although microbial corrosion is well-known in sea water, it is less investigated in supply water. Thus, an experimental water main was kept in operation for 6months. SRB were detected by BART tests in the test water main. Copyright © 2014 Elsevier B.V. All rights reserved.

Stability and electronic properties of oxygen-doped ZnS polytypes: DFTB study

NASA Astrophysics Data System (ADS)

Popov, Ilya S.; Vorokh, Andrey S.; Enyashin, Andrey N.

2018-06-01

Synthesis from aqueous solutions is an affordable method for fabrication of II-VI semiconductors. However, application of this method often imposes a disorder of crystal lattice, manifesting as a rich variety of polytypes arising from wurtzite and zinc blende phases. The origin of this disordering still remains debatable. Here, the influence of the most likely impurity at water environment - substitutional oxygen - on the polytypic equilibrium of zinc sulphide is studied by means of density-functional tight-binding method. According to calculations, the inclusion of such oxygen does not affect the polytypic equilibrium. Apart of thermodynamic stability, the electronic and elastic properties of ZnS polytypes are studied as the function of oxygen distribution.

Rare earth ions doped ZnO: Synthesis, characterization and preliminary photoactivity assessment

NASA Astrophysics Data System (ADS)

Cerrato, Erik; Gionco, Chiara; Berruti, Ilaria; Sordello, Fabrizio; Calza, Paola; Paganini, Maria Cristina

2018-08-01

This work reports the effect of doping zinc oxide with lanthanide ions on structural, EPR and UV visible properties. Bare and doped samples were synthesized using the simple and green hydrothermal process. Different rare earth ions (RE = La, Ce, Pr, Er and Yb) with 1% molar ratio RE/Zn were used. The samples have been studied using X Ray Diffraction, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and UV visible diffuse reflectance spectroscopy. Finally, electron paramagnetic resonance (EPR) spectroscopy, was used to assess the materials photoactivity under UV irradiation, both in solid state, to see the charge carriers' generation and in solution, evaluating the OH• radical formation using the DMPO (5,5-Dimethyl-1-Pyrroline-N-Oxide) spin trapping technique. The results suggest that the synthesized materials could be interesting systems for the photocatalytic abatement of emerging organic persistent pollutants in wastewater treatment plants.

Semiconductive materials and associated uses thereof

DOEpatents

Lynn, Kelvin [Pullman, WA; Jones, Kelly [Colfax, WA; Ciampi, Guido [Waltham, MA

2011-11-01

High rate radiation detectors are disclosed herein. The detectors include a detector material disposed inside the container, the detector material containing cadmium, tellurium, and zinc, a first dopant containing at least one of aluminum, chlorine, and indium, and a second dopant containing a rare earth metal. The first dopant has a concentration of about 500 to about 20,000 atomic parts per billion, and the second dopant has a concentration of about 200 to about 20,000 atomic parts per billion.

Semiconductive materials and associated uses thereof

DOEpatents

Lynn, Kelvin; Jones, Kelly; Ciampi, Guido

2012-10-09

High rate radiation detectors are disclosed herein. The detectors include a detector material disposed inside the container, the detector material containing cadmium, tellurium, and zinc, a first dopant containing at least one of aluminum, chlorine, and indium, and a second dopant containing a rare earth metal. The first dopant has a concentration of about 500 to about 20,000 atomic parts per billion, and the second dopant has a concentration of about 200 to about 20,000 atomic parts per billion.

Unraveling Recrystallization Mechanisms Governing Texture Development from Rare-Earth Element Additions to Magnesium

NASA Astrophysics Data System (ADS)

Imandoust, Aidin; Barrett, Christopher D.; Al-Samman, Talal; Tschopp, Mark A.; Essadiqi, Elhachmi; Hort, Norbert; El Kadiri, Haitham

2018-03-01

The origin of texture components often associated with rare-earth element (REE) additions in wrought magnesium alloys is a long-standing problem in magnesium technology. While their influence on the texture is unquestionable, it is not yet clear why certain texture components, such as < 11\\bar{2}1 > ||{extrusion}{direction}, are favored over other components typically observed in traditional magnesium alloys. The objective of this research is to identify the mechanisms accountable for these RE textures during early stages of recrystallization. Electron backscattered diffraction and transmission electron microscopy analyses reveal that REEs in zinc-containing magnesium alloys corroborate discontinuous dynamic recrystallization. REEs promote isotropic growth for all nuclei generated through the bulging mechanism. During nucleation, the effect of REEs on orientation selection was explained by the diversified activity of both < 10\\bar{1}0 > and [0001] Taylor axes in the same grain with a marked preference for [0001] rotations to occur first. During nuclei growth, no growth preference was observed when sufficient REEs are added in the zinc-containing magnesium alloys, instead isotropic nuclei growth across all grain orientations occurs. This phenomenon is attributed to REEs segregating to grain boundaries (GBs), in agreement with prior computational and theoretical results (Barrett et al., Scripta Mater 146:46-50, 2018) that show a more isotropic GB energy and mobility after segregation.

Positive anomalous concentrations of Pb in some gabbroic rocks of Afikpo basin southeastern Nigeria.

PubMed

Onwualu-John, J N

2016-08-01

Gabbroic rocks have intruded the sedimentary sequence at Ameta in Afikpo basin southeastern Nigeria. Petrographic and geochemical features of the rocks were studied in order to evaluate their genetic and geotectonic history. The petrographic results show that the rocks contain plagioclase, olivine, pyroxene, biotite, iron oxide, and traces of quartz in three samples. Major element characteristics show that the rocks are subalkaline. In addition, the rocks have geochemical characteristics similar to basaltic andesites. The trace elements results show inconsistent concentrations of high field strength elements (Zr, Nb, Th, Ta), moderate enrichment of large-ion lithophile elements (Rb, Sr, Ba) and low concentrations of Ni and Cr. Rare earth element results show that the rocks are characterized by enrichment of light rare earth elements, middle rare earth elements enrichment, and depletion of heavy rare earth elements with slight positive europium anomalies. Zinc concentrations are within the normal range in basaltic rocks. There are extremely high concentrations of Pb in three of the rock samples. The high Pb concentrations in some of these rocks could be as a result of last episodes of magmatic crystallization. The rocks intruded the Asu River Group; organic components in the sedimentary sequence probably contain Pb which has been assimilated into the magma at the evolutionary stage of the magma. Weathering of some rocks that contain galena could lead to an increase in the concentration of lead in the gabbroic rocks, especially when the migration and crystallization of magma take place in an aqueous environment. Nevertheless, high concentration of lead is hazardous to health and environment.

Material efficiency: rare and critical metals.

PubMed

Ayres, Robert U; Peiró, Laura Talens

2013-03-13

In the last few decades, progress in electronics, especially, has resulted in important new uses for a number of geologically rare metals, some of which were mere curiosities in the past. Most of them are not mined for their own sake (gold, the platinum group metals and the rare Earth elements are exceptions) but are found mainly in the ores of the major industrial metals, such as aluminium, copper, zinc and nickel. We call these major metals 'attractors' and the rare accompanying metals 'hitch-hikers'. The key implication is that rising prices do not necessarily call forth greater output because that would normally require greater output of the attractor metal. We trace the geological relationships and the functional uses of these metals. Some of these metals appear to be irreplaceable in the sense that there are no known substitutes for them in their current functional uses. Recycling is going to be increasingly important, notwithstanding a number of barriers.

Thermostructural Evaluation of Four Infrared Seeker Dome Materials. Part 2. Thermal and Mechanical Properties

DTIC Science & Technology

1985-04-01

Selenide (ZnSe) and Zinc Sulphide (ZnS). The mechanical properties used in the evaluation include tension, compression and flexure at room temperature...communicates with the atmosphere through a mercury column in order that the change in volume can be read directly in a burette. 17...The correction of the basket is subtracted from the measured mercury displacement and the result used to calculate specimen en~halpy above 32 ’F. The

Nanocomposite scintillator, detector, and method

DOEpatents

Cooke, D Wayne [Santa Fe, NM; McKigney, Edward A [Los Alamos, NM; Muenchausen, Ross E [Los Alamos, NM; Bennett, Bryan L [Los Alamos, NM

2009-04-28

A compact includes a mixture of a solid binder and at least one nanopowder phosphor chosen from yttrium oxide, yttrium tantalate, barium fluoride, cesium fluoride, bismuth germanate, zinc gallate, calcium magnesium pyrosilicate, calcium molybdate, calcium chlorovanadate, barium titanium pyrophosphate, a metal tungstate, a cerium doped nanophosphor, a bismuth doped nanophosphor, a lead doped nanophosphor, a thallium doped sodium iodide, a doped cesium iodide, a rare earth doped pyrosilicate, or a lanthanide halide. The compact can be used in a radiation detector for detecting ionizing radiation.

Zinc Isotopes as Tracers of Crust-Mantle Interactions and Mineralization Processes in Layered Intrusions

NASA Astrophysics Data System (ADS)

Day, J. M.; Moynier, F.

2016-12-01

Zinc isotopes are a powerful tool for studying igneous processes and may be useful for distinguishing between mantle or crustal origins for mineralization and for examining crystallization processes. Restricted ranges in δ66Zn for mantle-derived rocks (δ66Zn = 0.28±0.05‰; [{66Zn/64Znsample/66Zn/64ZnJMC-Lyon-1} × 1000] all uncertainties reported are 2SD) contrast the large δ66Zn variations in sedimentary rocks ( 0 to 1‰), or in volcanic and sedimentary hosted ore deposits (e.g., SEDEX; VHMS; MVT = -0.6 to 1.3‰). Here, we use Zn isotopes to investigate magmatic processes in the 1.27 Ga Muskox Intrusion (Canada) and 2.7 Ga Stillwater Intrusion (Montana). The Muskox main chromitite horizon has between 270-330 ppm Zn with δ66Zn ranging from 0.16 to 0.31‰. Zinc isotope compositions negatively correlate with Os isotopes. Chromitite (40a) with the lowest 187Os/188Os (0.132) has δ66Zn of 0.31±0.03‰; indistinguishable from the mantle value. CM19 glass from the co-eval Coppermine Volcanics, which has crust-like O and Nd isotopes but low 187Os/188Os (0.131), has been interpreted as the extrusive manifestation of chromitite genesis. The value of δ66Zn (0.27±0.07‰) for CM19 is within uncertainty of 40A, and permissive of formation during silicic-mafic melt mixing and large-scale chromitite crystallization. Stillwater chromitite seams exhibit a larger range in Zn (166-448 ppm), but generally lower δ66Zn (0.13±0.04‰) than Muskox chromitites, or to a JM Reef bulk sample (69 ppm Zn, δ66Zn = 0.22±0.03‰). These results suggest different sources of Zn for Ultramafic series chromitites versus the JM Reef (Banded series). Correspondingly, variations occur in Os isotopes for PGE poor chromitites (γOs = -2 to +4) versus the PGE-rich JM Reef (γOs = +12 to +34). Zinc isotope variations may be explained by either a mantle source with low δ66Zn that was subsequently contaminated by high δ66Zn crust, or from contamination of the ultramafic series by low δ66Zn continental lithospheric mantle. JM Reef sulphides span a wide range in Zn (1.8-350 ppm) and δ66Zn (-0.03 to 0.68‰) consistent with fractionation of Zn isotopes during sulphide melt-mineral crystallization. These results show promise for using Zn isotopes to study sources of mineralization and to elucidate sulphide crystallization processes.

Cellular Precipitates Of Iron Oxide in Olivine in a Stratospheric Interplanetary Dust Particle

NASA Technical Reports Server (NTRS)

Rietmeijer, Frans J. M.

1996-01-01

The petrology of a massive olivine-sulphide interplanetary dust particle shows melting of Fe,Ni-sulphide plus complete loss of sulphur and subsequent quenching to a mixture of iron-oxides and Fe,Ni-metal. Oxidation of the fayalite component in olivine produced maghemite discs and cellular intergrowths with olivine and rare andradite-rich garnet. Cellular reactions require no long-range solid-state diffusion and are kinetically favourable during pyrometamorphic oxidation. Local melting of the cellular intergrowths resulted in three dimensional symplectic textures. Dynamic pyrometamorphism of this asteroidal particle occurred at approx. 1100 C during atmospheric entry flash (5-15 s) heating.

The effect of different mouth rinse products on intra-oral halitosis.

PubMed

Erovic Ademovski, S; Lingström, P; Renvert, S

2016-05-01

To evaluate the effect of different mouth rinses 12 h after rinsing on genuine intra-oral halitosis. Twenty-four adults with halitosis were included in a double-blind, crossover, randomized clinical trial. Halitosis was evaluated 12 h after rinsing with placebo and five mouth rinse products containing zinc acetate and chlorhexidine diacetate; zinc lactate, chlorhexidine and cetylpyridinium chloride; zinc acetate and chlorhexidine diacetate with reduced amounts of mint and menthol; zinc chloride and essential oil; and chlorine dioxide using the organoleptic method and a gas chromatograph. Test periods were separated by 1 week. Hydrogen sulphide (H2 S), methyl mercaptan (MM) and the organoleptic scores (OLS) were significantly reduced 12 h following rinsing with all substances compared to placebo (P < 0.05). H2 S was more effectively reduced after rinsing with zinc acetate and chlorhexidine diacetate and zinc acetate and chlorhexidine diacetate with reduced amounts of mint and menthol compared to rinsing with zinc chloride and essential oil (P < 0.05), and significantly lower values of MM were obtained after rinsing with zinc acetate and chlorhexidine diacetate compared to zinc lactate, chlorhexidine and cetylpyridinium chloride (P < 0.05). The percentage effectively treated individuals (H2 S (<112 ppb), MM (<26 ppb) and OLS score <2) varied from 58% percentage (zinc acetate and chlorhexidine diacetate) to 26% (zinc chloride and essential oil). All treatments resulted in reduction in halitosis 12 h after rinsing compared to placebo. H2 S and MM were most effectively reduced by zinc acetate and chlorhexidine diacetate. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Comparative studies on the concentration of rare earth elements and heavy metals in the atmospheric particulate matter in Beijing, China, and in Delft, The Netherlands.

PubMed

Wang, C X; Zhu, W; Peng, A; Guichreit, R

2001-05-01

Atmospheric particulate matter (APM) was collected at three sampling sites in Beijing, China, from February to June 1998. The concentrations of rare earth elements (REE) and cobalt (Co), zinc (Zn), copper (Cu), cadmium (Cd) and lead (Pb) in the APM were determined by inductively coupled plasma mass spectrometry (ICP-MS). The results obtained in Beijing, China, were compared to that obtained in Delft, the Netherlands, in 1997. The influence of coal combustion was considered. The results demonstrated that the content of APM, the concentrations of REE and Co, Zn, Cd, Pb in the APM in Beijing, China, were higher than that in Delft, the Netherlands. From the ratios of La to Ce, and La to Sm, which may be used as tracers for the origin of the REE, it is concluded that the origins of REE in China differ from those in the Netherlands.

Fluorescent lighting with aluminum nitride phosphors

DOEpatents

Cherepy, Nerine J.; Payne, Stephen A.; Seeley, Zachary M.; Srivastava, Alok M.

2016-05-10

A fluorescent lamp includes a glass envelope; at least two electrodes connected to the glass envelope; mercury vapor and an inert gas within the glass envelope; and a phosphor within the glass envelope, wherein the phosphor blend includes aluminum nitride. The phosphor may be a wurtzite (hexagonal) crystalline structure Al.sub.(1-x)M.sub.xN phosphor, where M may be drawn from beryllium, magnesium, calcium, strontium, barium, zinc, scandium, yttrium, lanthanum, cerium, praseodymium, europium, gadolinium, terbium, ytterbium, bismuth, manganese, silicon, germanium, tin, boron, or gallium is synthesized to include dopants to control its luminescence under ultraviolet excitation. The disclosed Al.sub.(1-x)M.sub.xN:Mn phosphor provides bright orange-red emission, comparable in efficiency and spectrum to that of the standard orange-red phosphor used in fluorescent lighting, Y.sub.2O.sub.3:Eu. Furthermore, it offers excellent lumen maintenance in a fluorescent lamp, and does not utilize "critical rare earths," minimizing sensitivity to fluctuating market prices for the rare earth elements.

International Conference on Solid Films and Surfaces (2nd) (ICSFS-2), Programn and Abstracts Held at College Park, Maryland on 8-11 June 1981.

DTIC Science & Technology

1981-06-01

film recrystal- lization and the changing of their optical properties. The data of ther- mal treatment of the Zinc Sulphide and Magnium films in...11. J. KtEUZt 2:00 Surface Potentials of Benzene Derivative Monolayers and Submono- layers at the Mercury /Nitrogen Interface. B. J. KINZIG 2:20 Alkoxy...Potentials of Benzene Derivative Monolayers and Submonolayers at the Mercury /Nitrogen Interface by • B. J. Kinzig Naval Research Laboratory Optical

Transformations of Heavy Metals and Plant Nutrients in Dredged Sediments as Affected by Oxidation Reduction Potential and pH. Volume 1. Literature Review

DTIC Science & Technology

1977-05-01

895-896 (1974). 191. Fagerstrom, T., and Jernelov, A. "Formation of Methyl Mercury from Pure Mercuric Sulphide in Aerobic Organic Sediment." Water...was available. The toxic and nutrient elements included are lead, cadmium, mercury , arsenic, selenium, copper, zinc, manganese, iron, nitrogen...on the exchange of these materials between sediment and water. The toxic and nutrient elements included are lead, cadmium, mercury , ar- senic

Molar tooth carbonates and benthic methane fluxes in Proterozoic oceans.

PubMed

Shen, Bing; Dong, Lin; Xiao, Shuhai; Lang, Xianguo; Huang, Kangjun; Peng, Yongbo; Zhou, Chuanming; Ke, Shan; Liu, Pengju

2016-01-07

Molar tooth structures are ptygmatically folded and microspar-filled structures common in early- and mid-Proterozoic (∼2,500-750 million years ago, Ma) subtidal successions, but extremely rare in rocks <750 Ma. Here, on the basis of Mg and S isotopes, we show that molar tooth structures may have formed within sediments where microbial sulphate reduction and methanogenesis converged. The convergence was driven by the abundant production of methyl sulphides (dimethyl sulphide and methanethiol) in euxinic or H2S-rich seawaters that were widespread in Proterozoic continental margins. In this convergence zone, methyl sulphides served as a non-competitive substrate supporting methane generation and methanethiol inhibited anaerobic oxidation of methane, resulting in the buildup of CH4, formation of degassing cracks in sediments and an increase in the benthic methane flux from sediments. Precipitation of crack-filling microspar was driven by methanogenesis-related alkalinity accumulation. Deep ocean ventilation and oxygenation around 750 Ma brought molar tooth structures to an end.

Molar tooth carbonates and benthic methane fluxes in Proterozoic oceans

PubMed Central

Shen, Bing; Dong, Lin; Xiao, Shuhai; Lang, Xianguo; Huang, Kangjun; Peng, Yongbo; Zhou, Chuanming; Ke, Shan; Liu, Pengju

2016-01-01

Molar tooth structures are ptygmatically folded and microspar-filled structures common in early- and mid-Proterozoic (∼2,500–750 million years ago, Ma) subtidal successions, but extremely rare in rocks <750 Ma. Here, on the basis of Mg and S isotopes, we show that molar tooth structures may have formed within sediments where microbial sulphate reduction and methanogenesis converged. The convergence was driven by the abundant production of methyl sulphides (dimethyl sulphide and methanethiol) in euxinic or H2S-rich seawaters that were widespread in Proterozoic continental margins. In this convergence zone, methyl sulphides served as a non-competitive substrate supporting methane generation and methanethiol inhibited anaerobic oxidation of methane, resulting in the buildup of CH4, formation of degassing cracks in sediments and an increase in the benthic methane flux from sediments. Precipitation of crack-filling microspar was driven by methanogenesis-related alkalinity accumulation. Deep ocean ventilation and oxygenation around 750 Ma brought molar tooth structures to an end. PMID:26739600

Anthropogenic Cycles of Rare Earth Elements

NASA Astrophysics Data System (ADS)

Du, X.; Graedel, T. E.

2009-12-01

This research will develop quantitatively resolved anthropogenic cycles and in-use stocks for the rare earth metals specifically cerium, lanthanum and dysprosium in Japan, China, and the U.S. for the year of 2007. Rare earth elements (REE) is a group of 17 scare metals widely used in a growing number of emerging technologies and have been in high demand for emerging technologies as raw materials during past the three decades. New market participants from newly industrializing countries, primarily China, have had strong impacts on the demand of share. Consequently, the importance to sustain a reliable, steady, uninterrupted supply on global market triggered comprehensive research to recognize and understand the life cycles of rare earths. Moreover, because China plays a dominant role in mining production since 1990, it requires the assessment for the countries, which are almost completely dependent on imports from China with respect to rare earth resources. The study aims to analyze the flows and stocks of rare earth elements individually as elemental form in spite of their natural geological co-occurrence and mixed composition in applications. By applying the method of Material Flow Analysis (MFA) work has been done on evaluating current and historical flows of specific technologically significant materials, for example, copper, zinc, nickel, etc., determining the stocks available in different types of reservoirs (e.g., lithosphere, in-use) and the flows among the reservoirs, developing scenarios of possible futures of metal use, and assessing the environmental and policy implications of the results. Therefore, REE as a new target deserves inclusion because of its potential demand-supply conflict and importance to secure the competitive advantage of technical innovation in future. This work will generate a quantitatively resolved anthropogenic life cycle and in-use stocks for REE for the main target countries for a chosen year, 2007, providing flows and stocks from mining to use to recycling quantifying the cycles for Japan, China and the U.S. as three representative types of consumers and paying attention to aspects of resource sustainability. Being well aware of the stages in the metal life cycle helps the sustainable development and policy making in long term. The goal is to consider REE resource availability, sustainability, and development strategies in the future that can sustain a reliable, steady, uninterrupted REE supply on the global market.

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

NASA Astrophysics Data System (ADS)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Geophysical Characterization of a Rare Earth Element Enriched Carbonatite Terrane at Mountain Pass, California Eastern Mojave Desert

NASA Astrophysics Data System (ADS)

Denton, Kevin M.

Mountain Pass, California, located in the eastern Mojave Desert, hosts one of the world's richest rare earth element (REE) deposits. The REE-rich rocks occur in a 2.5 km- wide, north-northwest trending zone of Mesoproterozoic (1.4-1.42 Ga) stocks and dikes, which intrude a larger Paleoproterozoic (1.7 Ga) schist-gneiss terrane that extends 10 km southward from Clark Mountain to the Mescal Range. Several REE-enriched bodies make up the Mountain Pass intrusive suite including shonkinite, syenite, and granite comprising an ultrapotassic intrusive suite and the Sulphide Queen carbonatite body. Two-dimensional modeling of gravity, magnetic, and electrical resistivity data reveals that the Mountain Pass intrusive suite is associated with a local gravity high that is superimposed on a 4-km wide gravity terrace. Rock property data indicate that the Mountain Pass intrusive suite is unusually nonmagnetic at the surface (2.0 x 10-3 SI, n = 67). However, aeromagnetic data indicate that these rocks occur along the eastern edge of a prominent north-northwest trending aeromagnetic high of unknown origin. The source of this unknown magnetic anomaly is 2-3 km below the surface and coincides with a body of rock having high electrical conductivity. Electrical resistivity models indicate that this unknown magnetic anomaly is several orders of magnitude more conductive (103 O•m) than the surrounding rock. Combined geophysical data suggest that the carbonatite and its associated ultrapotassic intrusive suite were preferentially emplaced along a northwest zone of weakness and/or a fault.

Textures and trace element composition of pyrite from the Bukit Botol volcanic-hosted massive sulphide deposit, Peninsular Malaysia

NASA Astrophysics Data System (ADS)

Basori, Mohd Basril Iswadi; Gilbert, Sarah; Large, Ross Raymond; Zaw, Khin

2018-06-01

The Bukit Botol volcanic-hosted massive sulphide (VHMS) deposit is located in the Central Belt of Peninsular Malaysia. The deposit occurs in a package of Permian-aged coherent felsic volcanic and volcaniclastic rocks which have a geochemical signature indicative of a volcanic arc tectonic setting. Mineralisation shows distinct ore zonation, forming a stringer to massive sulphide zone at the footwall followed by barite lenses and exhalite layers (Fe-Mn ore) at the top. Mineralogy is characterised by pyrite as the major sulphide mineral, with minor chalcopyrite, sphalerite, and rare galena; traces of gold, silver- and tin-bearing minerals also occur in the massive sulphide and barite ores. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analysis combined with the textural characteristics of pyrite provides evidence for significant variations of trace elements in different pyrite types at Bukit Botol, having three types of pyrite in the paragenetic sequence. The concentrations of As, Se, Te, Cu, Zn and Pb decrease from the early pyrite 1 to the late stage pyrite 3, and the Co/Ni ratios vary for the three pyrite types. The combined textural and compositional data of pyrite suggest that the hydrothermal fluid responsible for mineralisation evolved from an early, high temperature, reduced, low pH and desulphurized fluid to more S-rich, oxidized, high pH and cooler fluid. Available sulphur isotope data from the Bukit Botol deposit point to reduced seawater, along with a possible magmatic contribution, as the most probable sources for the ore-forming fluids.

Silver aids healing in the sterile skin wound: experimental studies in the laboratory rat.

PubMed

Lansdown, A B; Sampson, B; Laupattarakasem, P; Vuttivirojana, A

1997-11-01

Incisional wounds 15 mm long were induced surgically in the back skin of young adult Wistar rats. They were sutured and used as an experimental model in the therapeutic evaluation of daily applications of 0.5 mL of silver nitrate (SN) at 0.01, 0.1 or 1.0% w/v aqueous solution, or 0.5 g silver sulphadiazine (SSD) over a 10-day period. Control wounds received deionized water only. The silver preparations were not toxic but SN did stain the hair and superficial layers of the stratum corneum. The wounds remained microbiologically clean. Wounds exposed to SN (0.1 or 1.0%) or SSD healed more rapidly than controls. From about the fourth day of treatment, we noted a more rapid exteriorization of sutures, improved wound closure and an earlier loss of scabs and wound debris. Silver treatment appeared to reduce the inflammatory and granulation tissue phases of healing and enhance epidermal repair. Silver from SN was deposited as silver sulphide in extrafollicular hair shafts and superficial aspects of the skin and wound debris but not at deeper levels. Silver uptake was four-fold higher in damaged skin than in intact tissue. SSD was absorbed by intact and wounded skin but the silver did not precipitate as silver sulphide and its localization in the tissue is not known. Uptake of silver from SN or SSD was associated with changes in the concentrations of zinc and calcium in the skin. Zinc levels were depressed during the inflammatory and proliferative phases of healing and then increased. Zinc concentrations had normalized by 10 days when wound healing was achieved. Calcium levels remained higher than normal throughout the observation period. The mechanism of action of silver in advancing wound healing in the rat is unclear. Its ability to reduce the inflammatory and granulation phases of healing, and to invoke metallothionein production and influence metal ion binding are possibly important.

Biochemical Connections Between the Atmosphere and the Ocean

NASA Astrophysics Data System (ADS)

Liss, P. S.

INTRODUCTION THE CHEMICAL COMPOSITION OF THE EARTH'S ATMOSPHERE AIR-SEA EXCHANGE OF GASES OF IMPORTANCE Ozone Manmade Carbon Dioxide Dimethyl Sulphide Dimethyl Selenide Ammonia IMPACT OF ATMOSPHERIC DUST ON OCEAN BIOCHEMISTRY GLOBAL PERSPECTIVES ON BIOGEOCHEMICAL FLUXES ACROSS THE AIR-SEA INTERFACE DMS and the CLAW Hypothesis Iron REFERENCES

Byproduct metals and rare-earth elements used in the production of light-emitting diodes—Overview of principal sources of supply and material requirements for selected markets

USGS Publications Warehouse

Wilburn, David R.

2012-01-01

The use of light-emitting diodes (LEDs) is expanding because of environmental issues and the efficiency and cost savings achieved compared with use of traditional incandescent lighting. The longer life and reduced power consumption of some LEDs have led to annual energy savings, reduced maintenance costs, and lower emissions of carbon dioxide, sulfur dioxide, and nitrogen oxides from powerplants because of the resulting decrease in energy consumption required for lighting applications when LEDs are used to replace less-energy-efficient sources. Metals such as arsenic, gallium, indium, and the rare-earth elements (REEs) cerium, europium, gadolinium, lanthanum, terbium, and yttrium are important mineral materials used in LED semiconductor technology. Most of the world's supply of these materials is produced as byproducts from the production of aluminum, copper, lead, and zinc. Most of the rare earths required for LED production in 2011 came from China, and most LED production facilities were located in Asia. The LED manufacturing process is complex and is undergoing much change with the growth of the industry and the changes in demand patterns of associated commodities. In many respects, the continued growth of the LED industry, particularly in the general lighting sector, is tied to its ability to increase LED efficiency and color uniformity while decreasing the costs of producing, purchasing, and operating LEDs. Research is supported by governments of China, the European Union, Japan, the Republic of Korea, and the United States. Because of the volume of ongoing research in this sector, it is likely that the material requirements of future LEDs may be quite different than LEDs currently (2011) in use as industry attempts to cut costs by reducing material requirements of expensive heavy rare-earth phosphors and increasing the sizes of wafers for economies of scale. Improved LED performance will allow customers to reduce the number of LEDs in automotive, electronic, and lighting applications, which could reduce the overall demand for material components. Non-Chinese sources for rare earths are being developed, and some of these new sources are likely to be operational in time to meet increasing demand for rare earths from the LED sector. Because most LED component production and manufacturing occurs in Asia and many LED producers have established supply contracts with Chinese producers of rare earths, a significant amount of the metallic gallium, indium, and the rare earths used for LED production will likely continue to come from Chinese sources at least for the next 5 years; however, a greater amount of these materials are now being processed in Japan, the Republic of Korea, and Taiwan. As non-Chinese sources of rare earths come into production, these new mines are likely to be sources of light REEs, but China will likely remain the leading source of supply for the heavy REEs suitable for use as LED dopants and phosphors at least for the next few years. Increased research in the development of phosphors that use smaller amounts of or different REEs is intended to reduce dependence on rare earths from China. Supply disruption of rare earths and other specialty metals could take place if China's specialty metal exports are redirected to domestic markets. The cost of recovery is high and the lifespan for LEDs is comparatively long; thus, the LED waste volume was low in 2010, and few LEDs were recycled. The minute metal content of LEDs leads to a high cost for recovery, so recycling of LEDs outside of electronic waste is unlikely in the near term, although some LED producers are evaluating recycling options. Recycling of metals from LEDs in electronic waste is possible if the costs of recovering metals are justified by demand and metal prices.

Sulphur isotope constraints on formation conditions of the Luiswishi ore deposit, Democratic Republic of Congo (DRC)

NASA Astrophysics Data System (ADS)

Lerouge, C.; Cailteux, J.; Kampunzu, A. B.; Milesi, J. P.; Fléhoc, C.

2005-07-01

Luiswishi is a Congo-type Neoproterozoic sediment-hosted stratiform Cu-Co ore deposit of the Central Africa Copperbelt, located northwest of Lubumbashi (DRC). The ores form two main Cu-Co orebodies hosted by the Mines Subgroup, one in the lower part of the Kamoto Formation and the other at the base of the Dolomitic Shales Formation. Sulphides occur essentially as early parallel layers of chalcopyrite and carrolite, and secondarily as late stockwork sulphides cross-cutting the bedding and the early sulphide generation. Both types of stratiform and stockwork chalcopyrite and carrolite were systematically analyzed for sulphur isotopes, along the lithostratigraphic succession of the Mine Series. The quite similar δ 34S values of stratiform sulphides and late stockwork sulphides suggest an in situ recrystallization or a slight remobilization of stockwork sulphides without attainment of isotopic equilibrium between different sulphide phases (chalcopyrite and carrolite). The distribution of δ 34S values (-14.4‰ to +17.5‰) combined with the lithology indicates a strong stratigraphic control of the sulphur isotope signature, supporting bacterial sulphate reduction during early diagenesis of the host sediments, in a shallow marine to lacustrine environment. Petrological features combined with sulphur isotopic data of sulphides at Luiswishi and previous results on nodules of anhydrite in the Mine Series indicate a dominant seawater/lacustrine origin for sulphates, precluding a possible hydrothermal participation. The high positive δ 34S values of sulphides in the lower orebody at Luiswishi, hosted in massive chloritic-dolomitic siltite (known as Grey R.A.T.), fine-grained stratified dolostone (D.Strat.) and silicified-stromatolitic dolomites alternating with chloritic-dolomitic silty beds (R.S.F.), suggest that they were probably deposited during a period of regression in a basin cut off from seawater. The variations of δ 34S values (i.e. the decrease of δ 34S values from the Kamoto Formation to the overlying Dolomitic Shales and then the slight increase from S.D.2d to S.D.3a and S.D.3b members) are in perfect agreement with the inferred lithological and transgressive-regressive evolution of the ore-hosting sedimentary rocks [Cailteux, J., 1994. Lithostratigraphy of the Neoproterozoic Shaba-type (Zaire) Roan Supergroup and metallogenesis of associated stratiform mineralization. In: Kampunzu A.B., Lubala, R.T. (Eds.), Neoproterozoic Belts of Zambia, Zaire and Namibia. Journal of African Earth Sciences 19, 279-301].

Mn-doped Zinc Sulphide nanocrystals for immunofluorescent labeling of epidermal growth factor receptors on cells and clinical tumor tissues

NASA Astrophysics Data System (ADS)

J, Aswathy; V, Seethalekshmy N.; R, Hiran K.; R, Bindhu M.; K, Manzoor; Nair, Shantikumar V.; Menon, Deepthy

2014-11-01

The field of molecular detection and targeted imaging has evolved considerably with the introduction of fluorescent semiconductor nanocrystals. Manganese-doped zinc sulphide nanocrystals (ZnS:Mn NCs), which are widely used in electroluminescent displays, have been explored for the first time for direct immunofluorescent (IF) labeling of clinical tumor tissues. ZnS:Mn NCs developed through a facile wet chemistry route were capped using amino acid cysteine, conjugated to streptavidin and thereafter coupled to biotinylated epidermal growth factor receptor (EGFR) antibody utilizing the streptavidin-biotin linkage. The overall conjugation yielded stable EGFR antibody conjugated ZnS:Mn NCs (EGFR ZnS:Mn NCs) with a hydrodynamic diameter of 65 ± 15 nm, and having an intense orange-red fluorescence emission at 598 nm. Specific labeling of EGF receptors on EGFR+ve A431 cells in a co-culture with EGFR-ve NIH3T3 cells was demonstrated using these nanoprobes. The primary antibody conjugated fluorescent NCs could also clearly delineate EGFR over-expressing cells on clinical tumor tissues processed by formalin fixation as well as cryopreservation with a specificity of 86% and accuracy of 88%, in comparison to immunohistochemistry. Tumor tissues labeled with EGFR ZnS:Mn NCs showed good fluorescence emission when imaged after storage even at 15 months. Thus, ZnS nanobioconjugates with dopant-dependent and stable fluorescence emission show promise as an efficient, target-specific fluorophore that would enable long term IF labeling of any antigen of interest on clinical tissues.

Efficacy of scalp hair decontamination following exposure to vapours of sulphur mustard simulants 2-chloroethyl ethyl sulphide and methyl salicylate.

PubMed

Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Prevost, Philippe; Maloni, Pascal; Torre, Franck; Asia, Laurence; Josse, Denis; Doumenq, Pierre

2017-04-01

Chemical warfare agents are an actual threat and victims' decontamination is a main concern when mass exposure occurs. Skin decontamination with current protocols has been widely documented, as well as surface decontamination. However, considering hair ability to trap chemicals in vapour phase, we investigated hair decontamination after exposure to sulphur mustard simulants methyl salicylate and 2-chloroethyl ethyl sulphide. Four decontamination protocols were tested on hair, combining showering and emergency decontamination (use of Fuller's earth or Reactive Skin Decontamination Lotion RSDL ® ). Both simulants were recovered from hair after treatment, but contents were significantly reduced (42-85% content allowance). Showering alone was the least efficient protocol. Concerning 2-chloroethyl ethyl sulphide, protocols did not display significant differences in decontamination efficacy. For MeS, use of emergency decontaminants significantly increased showering efficacy (10-20% rise), underlining their usefulness before thorough decontamination. Our results highlighted the need to extensively decontaminate hair after chemical exposure. Residual amounts after decontamination are challenging, as their release from hair could lead to health issues. Copyright © 2016. Published by Elsevier B.V.

Validation of optimization strategies using the linear structured production chains

NASA Astrophysics Data System (ADS)

Kusiak, Jan; Morkisz, Paweł; Oprocha, Piotr; Pietrucha, Wojciech; Sztangret, Łukasz

2017-06-01

Different optimization strategies applied to sequence of several stages of production chains were validated in this paper. Two benchmark problems described by ordinary differential equations (ODEs) were considered. A water tank and a passive CR-RC filter were used as the exemplary objects described by the first and the second order differential equations, respectively. Considered in the work optimization problems serve as the validators of strategies elaborated by the Authors. However, the main goal of research is selection of the best strategy for optimization of two real metallurgical processes which will be investigated in an on-going projects. The first problem will be the oxidizing roasting process of zinc sulphide concentrate where the sulphur from the input concentrate should be eliminated and the minimal concentration of sulphide sulphur in the roasted products has to be achieved. Second problem will be the lead refining process consisting of three stages: roasting to the oxide, oxide reduction to metal and the oxidizing refining. Strategies, which appear the most effective in considered benchmark problems will be candidates for optimization of the mentioned above industrial processes.

Leaching of S, Cu, and Fe from disseminated Ni-(Fe)-(Cu) sulphide ore during serpentinization of dunite host rocks at Mount Keith, Agnew-Wiluna belt, Western Australia

NASA Astrophysics Data System (ADS)

Gole, Martin J.

2014-10-01

Komatiite-hosted disseminated Ni sulphide deposits in the Agnew-Wiluna greenstone belt occur both above and below the olivine isograd that was imposed on the greenstone sequence during the M2 metamorphic/deformation event. Deposits in the northern and central part of the belt and that are located below the isograd (Mount Keith, Honeymoon Well and West Jordan) have complex sulphide mineralogy and strongly zoned sulphide assemblages. These range from least-altered assemblages of pentlandite-pyrrhotite-chalcopyrite±pyrite to altered assemblages of pentlandite±chalcopyrite, pentlandite-heazlewoodite (or millerite), heazlewoodite (or millerite), and rarely to heazlewoodite-native Ni. Deposits to the south and that are above of the olivine isograd (Six Mile, Goliath North) are dominated by less complex magmatic assemblages with a lower proportion of weakly altered pentlandite±chalcopyrite assemblages. More altered assemblages are uncommon in these deposits and occur as isolated patches around the periphery of the deposits. The sulphide zonation is reflected by whole-rock reductions in S, Cu, Fe and Zn, whereas Ni, Pt and Pd and, with some exceptions, Co are conservative. The leaching of S, Cu, Fe and Zn from sulphide assemblages and the whole rock was initiated by highly reduced conditions that were produced during low fluid/rock ratio serpentinization. Consumption of H2O resulted in Cl, a component of the fluid, being concentrated sufficiently to stabilise iowaite as part of lizardite-rich assemblages. Once the rate of olivine hydration reactions declined and during and after expansion and associated fracturing of the ultramafic sequence allowed higher fluid access, a more fluid-dominated environment formed and new carbonate-bearing fluid gained access to varying extents to the ultramafic rock sequence. This drove Cl from iowaite (to form pyroaurite) and caused the sulphide assemblages to be altered from the original magmatic assemblages and compositions to those stable at the prevailing fO2 and fS2 conditions. Mass transfer was made possible via metal chloride complexes and H2S with fluids driven by deformation associated with the M2 metamorphism. Disseminated deposits in higher metamorphic grade terrains where olivine was stable during peak metamorphism did not undergo the metasomatism seen in the deposits in areas of lower metamorphic grade. Some minor leaching of S, Fe and Cu occurred around the periphery of the deposits during early, pre-M2 peak metamorphism, but once olivine stability was reached the driving force for the series of leaching reactions was exhausted. The effect of this process on the original magmatic sulphides is to induce significant variability in texture, mineralogy and bulk composition and to markedly reduce the Fe and S contents of the sulphide fraction (in extreme cases to zero for both elements), and to reduce the volume of the sulphide fraction per unit of Ni. These changes impact unfavourably on Ni sulphide recoveries and metallurgical characteristics of these Ni ores.

Flotation as a remediation technique for heavily polluted dredged material. 2. Characterisation of flotated fractions.

PubMed

Cauwenberg, P; Verdonckt, F; Maes, A

1998-01-19

The particle size distribution and the metal speciation of the heavy metals were investigated on dredged sediment and on the fractions obtained by mechanical agitated (Denver) flotation. The transition metal ions (cadmium, copper, lead and zinc) were flotated specifically independent of the particle size. Particle size analysis, EDTA extraction and sequential extracts indicated that during flotation a redistribution of metals occurred due to the oxidation of metal sulphides. This oxidation process was more pronounced when the flotation was performed at higher pH values and resulted in a decrease in flotation specificity.

Thermal management of batteries

NASA Astrophysics Data System (ADS)

Gibbard, H. F.; Chen, C.-C.

Control of the internal temperature during high rate discharge or charge can be a major design problem for large, high energy density battery systems. A systematic approach to the thermal management of such systems is described for different load profiles based on: thermodynamic calculations of internal heat generation; calorimetric measurements of heat flux; analytical and finite difference calculations of the internal temperature distribution; appropriate system designs for heat removal and temperature control. Examples are presented of thermal studies on large lead-acid batteries for electrical utility load levelling and nickel-zinc and lithium-iron sulphide batteries for electric vehicle propulsion.

Low-Earth-Orbit (LEO) Life Cycle Evaluation of Nickel-Zinc Batteries

NASA Technical Reports Server (NTRS)

Coates, D.; Ferreira, E.; Nyce, M.; Charkey, A.

1997-01-01

The conclusion of the Low-Earth-Orbit (LEO) life cycle evaluation of nickel-zinc batteries are: that composite nickel electrode provide excellent performance at a reduced weight and lower cost; calcium / zinc electrode minimizes shape change; unioptimized cell designs yield 60 Wh/kg; nickel-zinc delivers 600 cycles at 80% DOD; long cycle life obtainable at low DOD; high rate capability power density; long-term failure mechanism is stack dry; and anomalous overcharge (1120%) greatly affected cell performance but did not induce failure and was recoverable.

Environmental geochemistry at Red Mountain, an unmined volcanogenic massive sulphide deposit in the Bonnifield district, Alaska Range, east-central Alaska

USGS Publications Warehouse

Eppinger, R.G.; Briggs, P.H.; Dusel-Bacon, C.; Giles, S.A.; Gough, L.P.; Hammarstrom, J.M.; Hubbard, B.E.

2007-01-01

The unmined, pyrite-rich Red Mountain (Dry Creek) deposit displays a remarkable environmental footprint of natural acid generation, high metal and exceedingly high rate earth element (REE) concentrations in surface waters. The volcanogenic massive sulphide deposit exhibits well-constrained examples of acid-generating, metal-leaching, metal-precipitation and self-mitigation (via co-precipitation, dilution and neutralization) processes that occur in an undisturbed natural setting, a rare occurrence in North America. Oxidative dissolution of pyrite and associated secondary reactions under near-surface oxidizing conditions are the primary causes for the acid generation and metal leaching. The deposit is hosted in Devonian to Mississippian felsic metavolcanic rocks of the Mystic Creek Member of the Totatlanika Schist. Water samples with the lowest pH (many below 3.5), highest specific conductance (commonly >2500 ??S/cm) and highest major- and trace-element concentrations are from springs and streams within the quartz-sericite-pyrite alteration zone. Aluminum, Cd, Co, Cu, Fe, Mn, Ni, Pb, Y, Zn and, particularly, the REEs are found in high concentrations, ranging across four orders of magnitude. Waters collected upstream from the alteration zone have near-neutral pH, lower specific conductance (370 to 830 ??S/cm), lower metal concentrations and measurable alkalinities. Water samples collected downstream of the alteration zone have pH and metal concentrations intermediate between these two extremes. Stream sediments are anomalous in Zn, Pb, S, Fe, Cu, As, Co, Sb and Cd relative to local and regional background abundances. Red Mountain Creek and its tributaries do not, and probably never have, supported significant aquatic life. ?? 2007 AAG/ Geological Society of London.

Control of oral malodour by dentifrices measured by gas chromatography.

PubMed

Newby, Evelyn E; Hickling, Jenneth M; Hughes, Francis J; Proskin, Howard M; Bosma, Marylynn P

2008-04-01

To evaluate the effect of toothpaste treatments on levels of oral volatile sulphur compounds (VSCs) measured by gas chromatography in two clinical studies. These were blinded, randomised, controlled, crossover studies with 16 (study A) or 20 (study B) healthy volunteers between the ages of 19-54. Study A: breath samples were collected at baseline, immediately and lhr after brushing. Four dentifrices (Zinc A, Zinc B, commercially available triclosan dentifrice and zinc free control) were evaluated. Study B: breath samples were collected at baseline, immediately, 1, 2, 3 and 7 hours after treatment. Subjects consumed a light breakfast then provided an additional breath sample between baseline assessment and treatment. Two dentifrices (gel-to-foam and a commercially available triclosan dentrifrice) were evaluated. Breath samples were collected in syringes and analysed for VSCs (hydrogen sulphide, methyl mercaptan and Total VSCs) utilising gas chromatography (GC) with flame photometric detection. Study A: immediately after treatment, a statistically significant reduction in VSCs from baseline was observed for Zinc A product only. A statistically significant reduction in VSCs from baseline was observed after 1 hour for all products. Both zinc products exhibited a significantly greater reduction from baseline VSCs than Colgate Total and Control at all time points. Study B: a statistically significant reduction in VSCs from baseline was observed at all time points for both products. The gel-to-foam product exhibited significantly greater reduction from baseline Total VSC concentration than Colgate Total at all time points from 1 hour post-treatment. Control of oral malodour by toothpaste treatment, evaluated as VSC levels using GC, has been demonstrated. Zinc is effective at reducing VSCs and the efficacy of zinc is formulation dependent. A gel-to-foam dentifrice was more effective at reducing VSCs than Colgate Total up to 7 hours.

Polyurethane Self-Priming Topcoats

DTIC Science & Technology

1992-06-23

of a combination of metal salts or pigments which consist essentially of calcium borosilicate, zinc salts of benzoic acids , and an alkaline earth...essentially of calcium borosilkate. zinc salts of benzoic acids , and an alkaline earth metal phos- phate such as zinc-barium phosphate. In addition, the...purpose* without the ">ic acids or substituted benzo.c acids , and c.lcium pavment of any royalties thereon or therefor. boros.hcate. All three of

Acquired Bilateral Longitudinal True Leukonychia in a 35-year-old Woman

PubMed Central

Mokhtari, Fatemeh; Mozafarpoor, Samaneh; Nouraei, Saeid; Nilforoushzadeh, Mohammad Ali

2016-01-01

Acquired bilateral longitudinal true leukonychia is a rare disorder. We present a case of a 35-year-old healthy woman presented with this unusual and rare manifestation. She mentioned a history of unprotected exposure to detergents and bleaching chemical agents. Considering her low zinc level, she was prescribed with zinc capsules and recommended to avoid chemical substances for 6 months. During bimonthly follow-up, her zinc level turned normal, and leukonychia subsequently disappeared. Bilateral longitudinal true leukonychia in the nails due to zinc deficiency and exposure to chemical substances has not been reported previously. Direct and indirect effects of chemical substances on matrix and the effect of zinc deficiency on healing process should be considered in these cases. PMID:27857831

The Not-So-Rare Earths.

ERIC Educational Resources Information Center

Muecke, Gunter K.; Moller, Peter

1988-01-01

Describes the characteristics of rare earth elements. Details the physical chemistry of rare earths. Reviews the history of rare earth chemistry and mineralogy. Discusses the mineralogy and crystallography of the formation of rare earth laden minerals found in the earth's crust. Characterizes the geologic history of rare earth elements. (CW)

Recovering heavy rare earth metals from magnet scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ott, Ryan T.; McCallum, Ralph W.; Jones, Lawrence L.

A method of treating rare earth metal-bearing permanent magnet scrap, waste or other material in a manner to recover the heavy rare earth metal content separately from the light rare earth metal content. The heavy rare earth metal content can be recovered either as a heavy rare earth metal-enriched iron based alloy or as a heavy rare earth metal based alloy.

Urinary p-cresol diagnosis using nanocomposite of ZnO/MoS2 and molecular imprinted polymer on optical fiber based lossy mode resonance sensor.

PubMed

Usha, Sruthi P; Gupta, Banshi D

2018-03-15

A lossy mode resonance (LMR) based sensor for urinary p-cresol testing on optical fiber substrate is developed. The sensor probe fabrication includes dip coating of nanocomposite layer of zinc oxide and molybdenum sulphide (ZnO/MoS 2 ) over unclad core of optical fiber as the transducer layer followed by the layer of molecular imprinted polymer (MIP) as the recognition medium. The addition of molybdenum sulphide in the transducer layer increases the absorption of light in the medium which enhances the LMR properties of zinc oxide thereby increasing the conductivity and hence the sensitivity of the sensor. The sensor probe is characterized for p-cresol concentration range from 0µM (reference sample) to 1000µM in artificially prepared urine. Optimizations of various probe fabrication parameters are carried to bring out the sensor's optimal performance with a sensitivity of 11.86nm/µM and 28nM as the limit of detection (LOD). A two-order improvement in LOD is obtained as compared to the recently reported p-cresol sensor. The proposed sensor possesses a response time of 15s which is 8 times better than that reported in the literature utilizing electrochemical method. Its response time is also better than the p-cresol sensor currently available in the market for the medical field. Thus, with a fast response, significant stability and repeatability, the proposed sensor holds practical implementation possibilities in the medical field. Further, the realization of sensor probe over optical fiber substrate adds remote sensing and online monitoring feasibilities. Copyright © 2017 Elsevier B.V. All rights reserved.

Synthesis and different optical properties of Gd2O3 doped sodium zinc tellurite glasses

NASA Astrophysics Data System (ADS)

Samanta, Buddhadev; Dutta, Dibakar; Ghosh, Subhankar

2017-06-01

A series of Gd2O3 doped sodium zinc tellurite [xGd2O3-(0.8-x) TeO2-0.1Na2O-0.1ZnO] glasses are prepared by the conventional melt quenching method and their optical properties have been studied. UV-vis spectrophotometric studies within the wavelength range from 230 nm-800 nm are carried out in the integrating sphere mode to study the effect of Gd2O3 doping on the optical band gap (Eg), refractive index (n), dielectric constant (εr) and susceptibility (χ). Other physical properties like molar volume, molar refraction, polarizability, metallization criterion, number density of rare-earth ions (N), polaron radius (rp), inter ionic distance (ri), molar cation polarizability (∑αi), number of oxide ions in chemical composition (NO2-), optical band gap based electronic oxide ion polarizability (αO2-) and optical basicity (Λ) of glass samples have been studied on the basis of UV-vis spectra and density profile of the different glasses.

Mineral resource of the month: rare earth elements

USGS Publications Warehouse

,

2011-01-01

The article provides information on rare earth elements, which are group of 17 natural metallic elements. The rare earth elements are scandium, yttrium and lanthanides and classified into light rare earth elements (LREE) and heavy rate earth elements (HREE). The principal ores of the rare earth elements are identified. An overview of China's production of 97 percent of the rare earths in the world is provided. Commercial applications of rare earths are described.

Hydrometallurgical Extraction of Zinc and Copper A 57Fe-Mössbauer and XRD Approach

NASA Astrophysics Data System (ADS)

Mulaba-Bafubiandi, A. F.; Waanders, F. B.

2005-02-01

The most commonly used route in the hydrometallurgical extraction of zinc and copper from a sulphide ore is the concentrate roast leach electro winning process. In the present investigation a zinc copper ore from the Maranda mine, located in the Murchison Greenstone Belt, South Africa, containing sphalerite (ZnS) and chalcopyrite (CuFeS2), was studied. The 57Fe-Mössbauer spectrum of the concentrate yielded pyrite, chalcopyrite and clinochlore, consistent with XRD data. Optimal roasting conditions were found to be 900°C for 3 h and the calcine produced contained according to X-ray diffractometry equal amounts of franklinite (ZnFe2O4) and zinc oxide (ZnO) and half the amount of willemite (Zn2SiO4). The Mössbauer spectrum showed predominantly franklinite (59%), hematite (6%) and other Zn- or Cu-depleted ferrites (35%). The latter could not be detected by XRD analyses as peak overlapping with other species occurred. Leaching was done with HCl, H2SO4 and HNO3, to determine which process would result in maximum recovery of Zn and Cu. More than 80% of both were recovered by using either one of the three techniques. From the residue of the leaching, the Fe-compounds were precipitated and <1% of the Zn and Cu was not recovered.

Ni, Cu, Au, and platinum-group element contents of sulphides associated with intraplate magmatism: A synthesis

USGS Publications Warehouse

Barnes, S.-J.; Zientek, M.L.; Severson, M.J.

1997-01-01

The tectonic setting of intraplate magmas, typically a plume intersecting a rift, is ideal for the development of Ni - Cu - platinum-group element-bearing sulphides. The plume transports metal-rich magmas close to the mantle - crust boundary. The interaction of the rift and plume permits rapid transport of the magma into the crust, thus ensuring that no sulphides are lost from the magma en route to the crust. The rift may contain sediments which could provide the sulphur necessary to bring about sulphide saturation in the magmas. The plume provides large volumes of mafic magma; thus any sulphides that form can collect metals from a large volume of magma and consequently the sulphides will be metal rich. The large volume of magma provides sufficient heat to release large quantities of S from the crust, thus providing sufficient S to form a large sulphide deposit. The composition of the sulphides varies on a number of scales: (i) there is a variation between geographic areas, in which sulphides from the Noril'sk - Talnakh area are the richest in metals and those from the Muskox intrusion are poorest in metals; (ii) there is a variation between textural types of sulphides, in which disseminated sulphides are generally richer in metals than the associated massive and matrix sulphides; and (iii) the massive and matrix sulphides show a much wider range of compositions than the disseminated sulphides, and on the basis of their Ni/Cu ratio the massive and matrix sulphides can be divided into Cu rich and Fe rich. The Cu-rich sulphides are also enriched in Pt, Pd, and Au; in contrast, the Fe-rich sulphides are enriched in Fe, Os, Ir, Ru, and Rh. Nickel concentrations are similar in both. Differences in the composition between the sulphides from different areas may be attributed to a combination of differences in composition of the silicate magma from which the sulphides segregated and differences in the ratio of silicate to sulphide liquid (R factors). The higher metal content of the disseminated sulphides relative to the massive and matrix sulphides may be due to the fact that the disseminated sulphides equilibrated with a larger volume of magma than massive and matrix sulphides. The difference in composition between the Cu- and Fe-rich sulphides may be the result of the fractional crystallization of monosulphide solid solution from a sulphide liquid, with the Cu-rich sulphides representing the liquid and the Fe-rich sulphides representing the cumulate.

Effects of acidic recharge on groundwater at the St. Kevin Gulch site, Leadville, Colorado

USGS Publications Warehouse

Paschke, S.S.; Harrison, W.J.; Walton-Day, K.

2001-01-01

The acid rock drainage-affected stream of St. Kevin Gulch recharges the Quaternary sand and gravel aquifer of Tennessee Park, near Leadville, Colorado, lowering pH and contributing iron, cadmium, copper, zinc and sulphate to the ground-water system. Dissolved metal mobility is controlled by the seasonal spring runoff as well as oxidation/reduction (redox) reactions in the aquifer. Oxidizing conditions occur in the unconfined portions of the aquifer whilst sulphate-reducing conditions are found down gradient where semi-confined groundwater flow occurs beneath a natural wetland. Iron-reducing conditions occur in the transition from unconfined to semi-confined groundwater flow. Dissolved iron concentrations are low to not detectable in the alluvial fan recharge zone and increase in a down gradient direction. The effects of low-pH, metal-rich recharge are pronounced during low-flow in the fall when there is a defined area of low pH groundwater with elevated concentrations of dissolved zinc, cadmium, copper and sulphate adjacent to St. Kevin Gulch. Dissolved metal and sulphate concentrations in the recharge zone are diluted during spring runoff, although the maximum concentrations of dissolved zinc, cadmium, copper and sulphate occur at selected down gradient locations during high flow. Dissolved zinc, cadmium and copper concentrations are low to not detectable, whereas dissolved iron concentrations are greatest, in groundwater samples from the sulphate-reducing zone. Attenuation of zinc, cadmium and copper beneath the wetland suggests sulphide mineral precipitation is occurring in the semi-confined aquifer, in agreement with previous site investigations and saturation index calculations. Adsorption of dissolved zinc, cadmium and copper onto iron hydroxides is a minor attenuation process due to the low pH of the groundwater system.

Electrical properties of CZTS pellets made from microwave-processed powder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghediya, Prashant R., E-mail: prashantghediya@yahoo.co.in; Chaudhuri, Tapas K.

2015-06-24

Electrical properties of the kesterite copper zinc tin sulphide (CZTS) pellets in the temperature range from 300 K to 500 K are reported. The pellets are p-type with thermoelectric power (TEP) of + 175 µV/K. Electrical conductivity (σ) increases with the temperatures and is found to be due to thermionic emission (TE) over grain boundary (GB) barriers with activation energy of 170 meV. CZTS pellets are made from micropowders synthesized by microwave irradiation of precursor solution. Formation of kesterite CZTS is confirmed by X-ray diffraction (XRD) and Raman spectroscopy. Scanning Electron Microscope (SEM) shows that powder is micron sized spherical particles.

Materials and Electronic Equipment Corrosion Tests in Some U.S. Navy Geothermal Environments.

DTIC Science & Technology

1983-03-01

dissolved solids ə 5.0 ə 5.0 Mercury ɘ.0002 ɘ.0002 Lithium ɘ.01 ɘ.01 Silica as Si0 2 ə.0 ə.0 Aluminum 0.1 ɘ.1 Boron 0.01 ɘ.01 Phosphate ɘ.1 ɘ...Nitrate 2.7 Fluoride 2.80 Iron 0.08 Manganese 0.07 Arsenic 0.20 Copper 0.02 Zinc 0.27 Total dissolved solids 7013.0 Mercury ɘ.0002 Lithium 0.16 Silica as...Behavior of Passive Layers on Titanium," Corrosion, Vol. 38 (5), 1982, pp. 237-240. 7. J. S. Smith and J. D. A. Miller. "Nature of Sulphides and Their

Germanium and rare earth elements in soils under different land use types in the area of Freiberg (Saxony, Germany)

NASA Astrophysics Data System (ADS)

Wiche, Oliver; Moschner, Christin; Székely, Balázs

2017-04-01

A geochemical mapping study was conducted to investigate the spatial distribution and chemical fractionation of germanium (Ge) and selected rare earth elements (REEs) in topsoils and soil-grown plants under different land use types (moist grassland, mesic grassland, arable land) in the area of Freiberg (Saxony, Germany). The area of Freiberg is characterized by the mining of polymetallic sulphide deposits (Pb, As, Zn, Cd) which led to the pollution of top soils with metals and metalloids due to local emissions from metal smelting plants that occur widespread in the area. Since Ge often appears to be associated to sulphide ores like sphalerite, galenite and argyrodite, (post-)mining areas such as the Freiberg region are paradigmatic for phytomining research. The study area covers approximately 1,000 km2 in the south of Central Saxony, and 138 samples from 46 sampling sites were examined. Additionally, at each sampling site plant samples were collected. On arable soils the plant samples represented the cultivated crop species. On sites in mesic and moist grassland, samples from the most dominant plant species were taken and measured with ICP-MS. Ge and REEs in soils were partitioned by a sequential extraction procedure into mobile/exchangeable (Fraction 1), acid soluble (Fraction 2), bound to organic matter (Fraction 3), amorphous Fe/Mn-oxides (Fraction 4), crystalline Fe/Mn-oxides (Fraction 5) and residual fractions (Fraction 6). Total concentrations of Ge and REEs in soil varied considerably ranging from 1.0 µg g-1 to 4.3 µg g-1 for Ge and 97 µg g-1 to 402 µg g-1 for total REE concentrations. Elements in potentially plant available fractions (sums of Fraction 1 - Fraction 4) represented 8% of total Ge and 30% of total REEs, respectively. Soils on moist grasslands contained significantly higher total concentrations of Ge and REEs and higher concentrations of Ge and REEs in potentially plant available soil fractions compared to soils of mesic grasslands and arable land. Highest concentrations of Ge could be measured in plant species growing on moist grassland. The results of this study indicate that moist grasslands may act as sinks for Ge and REEs. In these soils high amounts of soil organic matter may foster the formation of labile element pools, increasing the availability of Ge and REEs. These studies have been carried out in the framework of the PhytoGerm project, financed by the Federal Ministry of Education and Research, Germany. BS contributed as an Alexander von Humboldt Research Fellow. The authors are grateful to students and laboratory assistants contributing in the field work and sample preparation.

Production method for making rare earth compounds

DOEpatents

McCallum, R.W.; Ellis, T.W.; Dennis, K.W.; Hofer, R.J.; Branagan, D.J.

1997-11-25

A method of making a rare earth compound, such as a earth-transition metal permanent magnet compound, without the need for producing rare earth metal as a process step, comprises carbothermically reacting a rare earth oxide to form a rare earth carbide and heating the rare earth carbide, a compound-forming reactant (e.g., a transition metal and optional boron), and a carbide-forming element (e.g., a refractory metal) that forms a carbide that is more thermodynamically favorable than the rare earth carbide whereby the rare earth compound (e.g., Nd{sub 2}Fe{sub 14}B or LaNi{sub 5}) and a carbide of the carbide-forming element are formed.

Production method for making rare earth compounds

DOEpatents

McCallum, R. William; Ellis, Timothy W.; Dennis, Kevin W.; Hofer, Robert J.; Branagan, Daniel J.

1997-11-25

A method of making a rare earth compound, such as a earth-transition metal permanent magnet compound, without the need for producing rare earth metal as a process step, comprises carbothermically reacting a rare earth oxide to form a rare earth carbide and heating the rare earth carbide, a compound-forming reactant (e.g. a transition metal and optional boron), and a carbide-forming element (e.g. a refractory metal) that forms a carbide that is more thermodynamically favorable than the rare earth carbide whereby the rare earth compound (e.g. Nd.sub.2 Fe.sub.14 B or LaNi.sub.5) and a carbide of the carbide-forming element are formed.

Mineral resource of the month: zinc

USGS Publications Warehouse

Tolcin, Amy C.

2009-01-01

The article provides information on zinc, the fourth most-widely consumed metal. It traces the first use of zinc with the Romans' production of brass. It describes the presence of zinc in Earth's crust and the importance of sphalerite as a source of zinc and other some minor metal production. The production and consumption of zinc as well as the commercial and industrial uses of this metal are also discussed.

Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

DOEpatents

Ellis, Timothy W.; Schmidt, Frederick A.

1995-08-01

Method of treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation.

Early oxygenation of the terrestrial environment during the Mesoproterozoic.

PubMed

Parnell, John; Boyce, Adrian J; Mark, Darren; Bowden, Stephen; Spinks, Sam

2010-11-11

Geochemical data from ancient sedimentary successions provide evidence for the progressive evolution of Earth's atmosphere and oceans. Key stages in increasing oxygenation are postulated for the Palaeoproterozoic era (∼2.3 billion years ago, Gyr ago) and the late Proterozoic eon (about 0.8 Gyr ago), with the latter implicated in the subsequent metazoan evolutionary expansion. In support of this rise in oxygen concentrations, a large database shows a marked change in the bacterially mediated fractionation of seawater sulphate to sulphide of Δ(34)S < 25‰ before 1 Gyr to ≥50‰ after 0.64 Gyr. This change in Δ(34)S has been interpreted to represent the evolution from single-step bacterial sulphate reduction to a combination of bacterial sulphate reduction and sulphide oxidation, largely bacterially mediated. This evolution is seen as marking the rise in atmospheric oxygen concentrations and the evolution of non-photosynthetic sulphide-oxidizing bacteria. Here we report Δ(34)S values exceeding 50‰ from a terrestrial Mesoproterozoic (1.18 Gyr old) succession in Scotland, a time period that is at present poorly characterized. This level of fractionation implies disproportionation in the sulphur cycle, probably involving sulphide-oxidizing bacteria, that is not evident from Δ(34)S data in the marine record. Disproportionation in both red beds and lacustrine black shales at our study site suggests that the Mesoproterozoic terrestrial environment was sufficiently oxygenated to support a biota that was adapted to an oxygen-rich atmosphere, but had also penetrated into subsurface sediment.

Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

DOEpatents

Ellis, T.W.; Schmidt, F.A.

1995-08-01

A method is described for treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation. 2 figs.

On the shock response of the magnesium alloy Elektron 675

NASA Astrophysics Data System (ADS)

Hazell, Paul; Appleby-Thomas, Gareth; Siviour, Clive; Wielewski, Euan

2011-06-01

Alloying elements such as aluminium, zinc or rare-earths allow precipitation hardening of magnesium (Mg). The low densities of such strengthened Mg alloys have led to their adoption as aerospace materials and (more recently) they are being considered as armour materials. Consequently, understanding their response to high-strain rate loading is becoming increasingly important. Here, the plate-impact technique was employed to measure longitudinal stress evolution in armour-grade wrought Mg-alloy Elektron 675 under 1D shock loading. The strength and spall behaviour was interrogated, with an estimate made of the material's Hugoniot elastic limit. Finally, electron backscatter diffraction (EBSD) techniques were employed to investigate post-shock microstructural changes.

Rare earth elements: end use and recyclability

USGS Publications Warehouse

Goonan, Thomas G.

2011-01-01

Rare earth elements are used in mature markets (such as catalysts, glassmaking, lighting, and metallurgy), which account for 59 percent of the total worldwide consumption of rare earth elements, and in newer, high-growth markets (such as battery alloys, ceramics, and permanent magnets), which account for 41 percent of the total worldwide consumption of rare earth elements. In mature market segments, lanthanum and cerium constitute about 80 percent of rare earth elements used, and in new market segments, dysprosium, neodymium, and praseodymium account for about 85 percent of rare earth elements used. Regardless of the end use, rare earth elements are not recycled in large quantities, but could be if recycling became mandated or very high prices of rare earth elements made recycling feasible.

Zinc speciation in mining and smelter contaminated overbank sediments by EXAFS spectroscopy

NASA Astrophysics Data System (ADS)

Van Damme, An; Degryse, Fien; Smolders, Erik; Sarret, Géraldine; Dewit, Julie; Swennen, Rudy; Manceau, Alain

2010-07-01

Overbank sediments contaminated with metalliferous minerals are a source of toxic metals that pose risks to living organisms. The overbank sediments from the Geul river in Belgium contain 4000-69,000 mg/kg Zn as a result of mining and smelting activities, principally during the 19th century. Three main Zn species were identified by powder Zn K-edge EXAFS spectroscopy: smithsonite (ZnCO 3), tetrahedrally coordinated sorbed Zn (sorbed IVZn) and Zn-containing trioctahedral phyllosilicate. Smithsonite is a primary mineral, which accounts for approximately 20-60% of the Zn in sediments affected by mining and smelting of oxidized Zn ores (mostly carbonates and silicates). This species is almost absent in sediments affected by mining and smelting of both sulphidic (ZnS, PbS) and oxidized ores, presumably because of acidic dissolution associated with the oxidation of sulphides, as suggested by the lower pH of this second type of sediment (pH(CaCl 2) <7.0 vs. pH(CaCl 2) >7.0 for the first type). Thus, sulphide minerals in sediment deposits can act as a secondary source of dissolved metals by a chemical process analogous to acid mine drainage. The sorbed IVZn component ranges up to approximately 30%, with the highest proportion occurring at pH(CaCl 2) <7.0 as a result of the readsorption of dissolved Zn 2+ on sediments constituents. Kerolite-like Zn-rich phyllosilicate is the major secondary species in all samples, and in some the only detected species, thus providing the first evidence for pervasive sequestration of Zn into this newly formed precipitate at the field scale.

Surface mapping and drilling of extinct seafloor massive sulphide deposits (eSMS) from the TAG Hydrothermal Field, 26oN: A tale of two `Jaspers'

NASA Astrophysics Data System (ADS)

Stobbs, I. J.; Lusty, P.; Petersen, S.; Murton, B. J.

2017-12-01

Two extinct seafloor massive sulphide (eSMS) deposits within the TAG hydrothermal field, 26oN, mid-Atlantic ridge, were mapped and drilled: Southern Mound and the newly discovered `Rona Mound'. Surface mapping was undertaken by combining high definition video footage and high resolution bathymetry to interpret surface geological and geomorphological features. Drill core was recovered using the BGS RD2 robotic drilling rig. Surface mapping of the mounds revealed a superficial cover of carbonate and iron-oxyhydroxides sediments, observed to directly overly oxide coated sulphide material within fault scarps, which dissect the flanks of both mounds. Drilling at the summits of the mounds revealed similar stratigraphy to the mapping, with the addition of a coherent and dense layer of red-coloured silica-rich `jasper', up to 3m thick, underlying the sediments and overlying unoxidised massive sulphides. The jasper mineralogy is dominated by silica, with minor iron oxides and rare disseminated sulphides. It displays a range of complex textures including filamentous and dendritic iron oxides often coated in silica. Drill core samples show the material to be porous, but relatively impermeable. Strong and positive Eu (REE) anomalies indicates a hydrothermal origin with little evidence of a seawater signature (lack of negative Ce anomaly). Silica precipitation is associated with low temperature hydrothermal activity, chert and jasper materials are locally present within the nearby hydrothermally active TAG mound and are more widespread at low-temperature diffuse hydrothermal sites such as within the MESO field. We interpret the `jasper' layers to be a common product, formed during the waning, low temperature, stage of the hydrothermal cycle which may form an impermeable and resistant `cap' that protects the underlying massive sulphide ore body from oxidation and dissolution. The formation of a `jasper cap' could act automatically to preserve eSMS deposits when hydrothermal circulation ceases and is essential to preserving the resource potential of eSMS deposits. This `jasper' capping layer is important from an economic perspective, and reinforces the need for shallow sub-seafloor mapping as part of any deep-sea mineral exploration. This research received funding from the EC FP7 project Blue Mining (604500).

Trace element carriers in combined sewer during dry and wet weather: an electron microscope investigation.

PubMed

El Samrani, A G; Lartiges, B S; Ghanbaja, J; Yvon, J; Kohler, A

2004-04-01

The nature of trace element carriers contained in sewage and combined sewer overflow (CSO) was investigated by TEM-EDX-Electron diffraction and SEM-EDX. During dry weather, chalcophile elements were found to accumulate in sewer sediments as early diagenetic sulfide phases. The sulfurization of some metal alloys was also evidenced. Other heavy metal carriers detected in sewage include metal alloys, some iron oxihydroxide phases and neoformed phosphate minerals such as anapaite. During rain events, the detailed characterization of individual mineral species allowed to differentiate the contributions from various specific sources. Metal plating particles, barite from automobile brake, or rare earth oxides from catalytic exhaust pipes, originate from road runoff, whereas PbSn alloys and lead carbonates are attributed to zinc-works from roofs and paint from building siding. Soil contribution can be traced by the presence of clay minerals, iron oxihydroxides, zircons and rare earth phosphates. However, the most abundant heavy metal carriers in CSO samples were the sulfide particles eroded from sewer sediments. The evolution of relative abundances of trace element carriers during a single storm event, suggests that the pollution due to the "first flush" effect principally results from the sewer stock of sulfides and previously deposited metal alloys, rather than from urban surface runoff.

Rare Earth Elements | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

- Mineral Resources main content Rare Earth Elements Rare earth elements and the supply and demand of these deposits containing rare earth elements to meet the perceived future demand. High prices for rare earth earth element occurrences in the DGGS publications catalog. Department of Natural Resources, Division of

Mineralogy of the epithermal precious and base metal deposit Banská Hodruša at the Rozália Mine (Slovakia)

NASA Astrophysics Data System (ADS)

Kubač, Alexander; Chovan, Martin; Koděra, Peter; Kyle, J. Richard; Žitňan, Peter; Lexa, Jaroslav; Vojtko, Rastislav

2018-03-01

The Au-Ag-Pb-Zn-Cu epithermal deposit Banská Hodruša of intermediate-sulphidation type is located in the Middle Miocene Štiavnica stratovolcano on the inner side of the Carpathian arc in Slovakia. This deposit represents an unusual subhorizontal multi-stage vein system, related to processes of underground cauldron subsidence and exhumation of a subvolcanic granodiorite pluton. Veins are developed on a low-angle normal shear zone, possibly representing a detachment zone in andesitic wall rocks that formed during emplacement and exhumation of the granodiorite pluton. The deposit consists of two parts, separated by a thick sill of quartz-diorite porphyry. The eastern part is currently mined, and the western part has already been depleted. The Banská Hodruša mineralization was formed during four stages: (1) low-grade silicified breccia at subhorizontal structures at the base of the deposit; (2) stockwork of steep veins with rhodonite-rhodochrosite, quartz-sulphide-carbonate and quartz-gold assemblages; (3) thin quartz-gold veins with medium dip in tension cracks inside the shear zone and complementary detachment hosted quartz-base metals-gold veins; (4) Post-ore veins. Gold and electrum (920-730) occur as intergrowths with base metal sulphides or hosted in quartz and carbonates, accompanied by Au-Ag tellurides (hessite, petzite). Rare Te-polybasite and Cu-cervelleite result from re-equilibration of early Te-bearing minerals during cooling. Sulphide minerals include low Fe sphalerite ( 1.25 wt%), galena, chalcopyrite, and pyrite. The wall rock alteration is represented mostly by adularia, illite, chlorite, quartz, calcite and pyrite. Precipitation of gold, Au-Ag tellurides, Mn-bearing minerals and adularia resulted from boiling of fluids due to hydraulic fracturing, as well as opening of dilatational structures within the shear zone.

Reactive Oxygen Species on the Early Earth and Survival of Bacteria

NASA Technical Reports Server (NTRS)

Balk, Melikea; Mason, Paul; Stams, Alfons J. M.; Smidt, Hauke; Freund, Friedemann; Rothschild, Lynn

2011-01-01

An oxygen-rich atmosphere appears to have been a prerequisite for complex, multicellular life to evolve on Earth and possibly elsewhere in the Universe. However it remains unclear how free oxygen first became available on the early Earth. A potentially important, and as yet poorly constrained pathway, is the production of oxygen through the weathering of rocks and release into the near-surface environment. Reactive Oxygen Species (ROS), as precursors to molecular oxygen, are a key step in this process, and may have had a decisive impact on the evolution of life, present and past. ROS are generated from minerals in igneous rocks during hydrolysis of peroxy defects, which consist of pairs of oxygen anions oxidized to the valence state -1 and during (bio) transformations of iron sulphide minerals. ROS are produced and consumed by intracellular and extracellular reactions of Fe, Mn, C, N, and S species. We propose that, despite an overall reducing or neutral oxidation state of the macroenvironment and the absence of free O2 in the atmosphere, organisms on the early Earth had to cope with ROS in their microenvironments. They were thus under evolutionary pressure to develop enzymatic and other defences against the potentially dangerous, even lethal effects of oxygen and its derived ROS. Conversely it appears that microorganisms learned to take advantage of the enormous reactive potential and energy gain provided by nascent oxygen. We investigate how oxygen might be released through weathering. We test microorganisms in contact with rock surfaces and iron sulphides. We model bacteria such as Deionococcus radiodurans and Desulfotomaculum, Moorella and Bacillus species for their ability to grow or survive in the presence of ROS. We examine how early Life might have adapted to oxygen.

Raman scattering of rare earth hexaborides

NASA Astrophysics Data System (ADS)

Ogita, Norio; Hasegawa, Takumi; Udagawa, Masayuki; Iga, Fumitoshi; Kunii, Satoru

2009-06-01

Raman scattering spectra were measured for the rare-earth hexaborides RB6 (R = Ce, Gd, or Dy). All Raman-active phonons due to B6 vibrations were observed in the range 600 - 1400 cm-1. Anomalous peaks were detected below 200 cm-1, which correspond to vibrations of rare-earth ion excited by second-order Raman scattering process. The intensity and energy of the rare-earth mode decrease with decreasing temperature. This suggests that the rare-earth ion vibrates in a shallow and anharmonic potential due to the boron cage. Using the reported values of mean square displacement of rare-earth ion, we estimated the anharmonic contribution for the rare-earth vibrations.

Magnetic Nanofluid Rare Earth Element Extraction Process Report, Techno Economic Analysis, and Results for Geothermal Fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pete McGrail

This GDR submission is an interim technical report and raw data files from the first year of testing on functionalized nanoparticles for rare earth element extraction from geothermal fluids. The report contains Rare Earth Element uptake results (percent removal, mg Rare Earth Element/gram of sorbent, distribution coefficient) for the elements of Neodymium, Europium, Yttrium, Dysprosium, and Cesium. A detailed techno economic analysis is also presented in the report for a scaled up geothermal rare earth element extraction process. All rare earth element uptake testing was done on simulated geothermal brines with one rare earth element in each brine. The raremore » earth element uptake testing was conducted at room temperature.« less

Transient symptomatic zinc deficiency in a preterm exclusively breast-fed infant.

PubMed

Laureano, André; Brás, Susana; Carvalho, Rodrigo; Amaro, Cristina; Cardoso, Jorge

2014-02-18

A 5-month-old female infant, preterm, exclusively breast-fed, presented with a 2-month history of erythematous, erosive, and crusted patches and plaques in a peri-oral, scalp, genital, and peri-anal distribution. A clinical diagnosis of zinc deficiency was confirmed by a low serum zinc level in the infant and decreased maternal breast milk zinc. Complete resolution occurred within two weeks of oral zinc supplementation. Acquired zinc deficiency is a rare nutritional disorder of infants. Early diagnosis and adequate treatment will prevent associated morbidity and complications.

Evolutionary ecology during the rise of dioxygen in the Earth's atmosphere.

PubMed

Sleep, Norman H; Bird, Dennis K

2008-08-27

Pre-photosynthetic niches were meagre with a productivity of much less than 10(-4) of modern photosynthesis. Serpentinization, arc volcanism and ridge-axis volcanism reliably provided H(2). Methanogens and acetogens reacted CO(2) with H(2) to obtain energy and make organic matter. These skills pre-adapted a bacterium for anoxygenic photosynthesis, probably starting with H(2) in lieu of an oxygen 'acceptor'. Use of ferrous iron and sulphide followed as abundant oxygen acceptors, allowing productivity to approach modern levels. The 'photobacterium' proliferated rooting much of the bacterial tree. Land photosynthetic microbes faced a dearth of oxygen acceptors and nutrients. A consortium of photosynthetic and soil bacteria aided weathering and access to ferrous iron. Biologically enhanced weathering led to the formation of shales and, ultimately, to granitic rocks. Already oxidized iron-poor sedimentary rocks and low-iron granites provided scant oxygen acceptors, as did freshwater in their drainages. Cyanobacteria evolved dioxygen production that relieved them of these vicissitudes. They did not immediately dominate the planet. Eventually, anoxygenic and oxygenic photosynthesis oxidized much of the Earth's crust and supplied sulphate to the ocean. Anoxygenic photosynthesis remained important until there was enough O(2) in downwelling seawater to quantitatively oxidize massive sulphides at mid-ocean ridge axes.

Enhanced pinning in mixed rare earth-123 films

DOEpatents

Driscoll, Judith L [Los Alamos, NM; Foltyn, Stephen R [Los Alamos, NM

2009-06-16

An superconductive article and method of forming such an article is disclosed, the article including a substrate and a layer of a rare earth barium cuprate film upon the substrate, the rare earth barium cuprate film including two or more rare earth metals capable of yielding a superconductive composition where ion size variance between the two or more rare earth metals is characterized as greater than zero and less than about 10.times.10.sup.-4, and the rare earth barium cuprate film including two or more rare earth metals is further characterized as having an enhanced critical current density in comparison to a standard YBa.sub.2Cu.sub.3O.sub.y composition under identical testing conditions.

Selective Emitter Pumped Rare Earth Laser

NASA Technical Reports Server (NTRS)

Chubb, Donald L. (Inventor); Patton, Martin O. (Inventor)

2001-01-01

A selective emitter pumped rare earth laser provides an additional type of laser for use in many laser applications. Rare earth doped lasers exist which are pumped with flashtubes or laser diodes. The invention uses a rare earth emitter to transform thermal energy input to a spectral band matching the absorption band of a rare earth in the laser in order to produce lasing.

2nd International Symposium on Fundamental Aspects of Rare-earth Elements Mining and Separation and Modern Materials Engineering (REES-2015)

NASA Astrophysics Data System (ADS)

Tavadyan, Levon, Prof; Sachkov, Viktor, Prof; Godymchuk, Anna, Dr.; Bogdan, Anna

2016-01-01

The 2nd International Symposium «Fundamental Aspects of Rare-earth Elements Mining and Separation and Modern Materials Engineering» (REES2015) was jointly organized by Tomsk State University (Russia), National Academy of Science (Armenia), Shenyang Polytechnic University (China), Moscow Institute of Physics and Engineering (Russia), Siberian Physical-technical Institute (Russia), and Tomsk Polytechnic University (Russia) in September, 7-15, 2015, Belokuriha, Russia. The Symposium provided a high quality of presentations and gathered engineers, scientists, academicians, and young researchers working in the field of rare and rare earth elements mining, modification, separation, elaboration and application, in order to facilitate aggregation and sharing interests and results for a better collaboration and activity visibility. The goal of the REES2015 was to bring researchers and practitioners together to share the latest knowledge on rare and rare earth elements technologies. The Symposium was aimed at presenting new trends in rare and rare earth elements mining, research and separation and recent achievements in advanced materials elaboration and developments for different purposes, as well as strengthening the already existing contacts between manufactures, highly-qualified specialists and young scientists. The topics of the REES2015 were: (1) Problems of extraction and separation of rare and rare earth elements; (2) Methods and approaches to the separation and isolation of rare and rare earth elements with ultra-high purity; (3) Industrial technologies of production and separation of rare and rare earth elements; (4) Economic aspects in technology of rare and rare earth elements; and (5) Rare and rare earth based materials (application in metallurgy, catalysis, medicine, optoelectronics, etc.). We want to thank the Organizing Committee, the Universities and Sponsors supporting the Symposium, and everyone who contributed to the organization of the event and to publication of this proceeding.

Genetic causes and gene–nutrient interactions in mammalian zinc deficiencies: acrodermatitis enteropathica and transient neonatal zinc deficiency as examples.

PubMed

Kasana, Shakhenabat; Din, Jamila; Maret, Wolfgang

2015-01-01

Discovering genetic causes of zinc deficiency has been a remarkable scientific journey. It started with the description of a rare skin disease, its treatment with various agents, the successful therapy with zinc, and the identification of mutations in a zinc transporter causing the disease. The journey continues with defining the molecular and cellular pathways that lead to the symptoms caused by zinc deficiency. Remarkably, at least two zinc transporters from separate protein families are now known to be involved in the genetics of zinc deficiency. One is ZIP4, which is involved in intestinal zinc uptake. Its mutations can cause acrodermatitis enteropathica (AE) with autosomal recessive inheritance. The other one is ZnT2, the transporter responsible for supplying human milk with zinc. Mutations in this transporter cause transient neonatal zinc deficiency (TNZD) with symptoms similar to AE but with autosomal dominant inheritance. The two diseases can be distinguished in affected infants. AE is fatal if zinc is not supplied to the infant after weaning, whereas TNZD is a genetic defect of the mother limiting the supply of zinc in the milk, and therefore the infant usually will obtain enough zinc once weaned. Although these diseases are relatively rare, the full functional consequences of the numerous mutations in ZIP4 and ZnT2 and their interactions with dietary zinc are not known. In particular, it remains unexplored whether some mutations cause milder disease phenotypes or increase the risk for other diseases if dietary zinc requirements are not met or exceeded. Thus, it is not known whether widespread zinc deficiency in human populations is based primarily on a nutritional deficiency or determined by genetic factors as well. This consideration becomes even more significant with regard to mutations in the other 22 human zinc transporters, where associations with a range of diseases, including diabetes, heart disease, and mental illnesses have been observed. Therefore, clinical tests for genetic disorders of zinc metabolism need to be developed.

Accumulation of rare earth elements by siderophore-forming Arthrobacter luteolus isolated from rare earth environment of Chavara, India.

PubMed

Emmanuel, E S Challaraj; Ananthi, T; Anandkumar, B; Maruthamuthu, S

2012-03-01

In this study, Arthrobacter luteolus, isolated from rare earth environment of Chavara (Quilon district, Kerala, India), were found to produce catechol-type siderophores. The bacterial strain accumulated rare earth elements such as samarium and scandium. The siderophores may play a role in the accumulation of rare earth elements. Catecholate siderophore and low-molecular-weight organic acids were found to be present in experiments with Arthrobacter luteolus. The influence of siderophore on the accumulation of rare earth elements by bacteria has been extensively discussed.

Health risk assessment of rare earth elements in cereals from mining area in Shandong, China.

PubMed

Zhuang, Maoqiang; Wang, Liansen; Wu, Guangjian; Wang, Kebo; Jiang, Xiaofeng; Liu, Taibin; Xiao, Peirui; Yu, Lianlong; Jiang, Ying; Song, Jian; Zhang, Junli; Zhou, Jingyang; Zhao, Jinshan; Chu, Zunhua

2017-08-29

To investigate the concentrations of rare earth elements in cereals and assess human health risk through cereal consumption, a total of 327 cereal samples were collected from rare earth mining area and control area in Shandong, China. The contents of 14 rare earth elements were determined by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The medians of total rare earth elements in cereals from mining and control areas were 74.22 μg/kg and 47.83 μg/kg, respectively, and the difference was statistically significant (P < 0.05). The wheat had the highest rare earth elements concentrations (109.39 μg/kg and 77.96 μg/kg for mining and control areas, respectively) and maize had the lowest rare earth elements concentrations (42.88 μg/kg and 30.25 μg/kg for mining and control areas, respectively). The rare earth elements distribution patterns for both areas were characterized by enrichment of light rare earth elements. The health risk assessment demonstrated that the estimated daily intakes of rare earth elements through cereal consumption were considerably lower than the acceptable daily intake (70 μg/kg bw). The damage to adults can be neglected, but more attention should be paid to the effects of continuous exposure to rare earth elements on children.

Rare Earth Element Mines, Deposits, and Occurrences

USGS Publications Warehouse

Orris, Greta J.; Grauch, Richard I.

2002-01-01

Data on rare earth (including yttrium) mines, deposits, and occurrences were compiled as part of an effort by the USGS and the University of Arizona Center for Mineral Resources to summarize current knowledge on the supply and demand outlook and related topics for this group of elements. Economic competition and environmental concerns are increasingly constraining the mining and processing of rare earths from the Mountain Pass mine in California. For many years, the deposit at Mountain Pass was the world's dominant source of rare earth elements and the United States was essentially self-sufficient. Starting approximately 10 years ago, the U.S. has become increasingly dependent (> 90 percent of separated rare earths) upon imports from China, now the dominant source of rare earths. A knowledge of the known economic and noneconomic sources of rare earths is basic to evaluating the outlook for rare earth supply and associated issues.

Radioactive rare-earth deposit at Scrub Oaks mine, Morris County, New Jersey

USGS Publications Warehouse

Klemic, Harry; Heyl, A.V.; Taylor, Audrey R.; Stone, Jerome

1959-01-01

A deposit of rare-earth minerals in the Scrub Oaks iron mine, Morris County, N. J., was mapped and sampled in 1955. The rare-earth minerals are mainly in coarse-grained magnetite ore and in pegmatite adjacent to it. Discrete bodies of rare-earth-bearing magnetite ore apparently follow the plunge of the main magnetite ore body at the north end of the mine. Radioactivity of the ore containing rare earths is about 0.2 to 0.6 mllliroentgens per hour. The principal minerals of the deposit are quartz, magnetite, hematite, albiteoligoclase, perthite and antiperthite. Xenotime and doverite aggregates and bastnaesite with intermixed leucoxene are the most abundant rare-earth minerals, and zircon, sphene, chevkinite, apatite, and monazite are of minor abundance in the ore. The rare-earth elements are partly differentiated into cerium-rich bastnaesite, chevkinite, and monazite, and yttrium-rich xenotime and doverite. Apatite, zircon, and sphene contain both cerium and yttrium group earths. Eleven samples of radioactive ore and rock average 0.009 percent uranium, 0.062 percent thorium, 1.51 percent combined rare-earth oxides including yttrium oxide and 24.8 percent iron. Scatter diagrams of sample data show a direct correlation between equivalent uranium, uranium, thorium, and combined rare^ earth oxides. Both cerium- and yttrium-group earths are abundant in the rare-earth minerals. Radioactive magnetite ore containing rare-earth minerals probably formed as a variant of the magnetite mineralization that produced the main iron ore of the Scrub Oaks deposit. The rare-earth minerals and the iron ore were deposited contemporaneously. Zircon crystals, probably deposited at the same time, have been determined by the Larsen method to be about 550 to 600 million years old (late Precambrian age). Uranium, thorium, and rare-earth elements are potential byproducts of iron in the coarse-grained magnetite ore.

Gravity and magnetic studies of the eastern Mojave Desert, California and Nevada

USGS Publications Warehouse

Denton, Kevin M.; Ponce, David A.

2016-06-17

IntroductionFrom May 2011 to August 2014, the U.S. Geological Survey (USGS) collected gravity data at more than 2,300 stations and physical property measurements on more than 640 rock samples from outcrops in the eastern Mojave Desert, California and Nevada. Gravity, magnetic, and physical-property data are used to study and locate regional crustal structures as an aid to understanding the geologic framework related to mineral resources of the eastern Mojave Desert.The eastern Mojave Desert is host to a world-class rare earth element carbonatite deposit located at Mountain Pass, California. Carbonatites are typically defined as magmatic rocks with high modal abundances of primary carbonate minerals >50 weight percent and elevated abundances of rare earth elements (REEs) (Nelson and others, 1988; Woolley and Kempe, 1989). The “Sulphide Queen” carbonatite ore deposit is a composite, tabular body made up of sills and dikes of REE-bearing sovites and beforsites that occurs just south of the Clark Mountain Range along a north-northwest trending fault-bounded block that extends along the northeast edge of the Mescal Range and northwestern extent of Ivanpah Mountains. This early to middle Proterozoic block is composed of a 1.7 Ga metamorphic complex of gneiss and schist that underwent widespread metamorphism and associated plutonism during the Ivanpah orogeny (Miller and others, 2007). Subsequently, these rocks were intruded by a series of granitoids, which included the 1.4 Ga (DeWitt and others, 1987) ultrapotassic alkaline suite of intrusions that are spatially and temporally associated with hundreds of dikes, outcrops, and a carbonatite ore body. The relative age sequence of this intrusive suite of alkaline rocks from oldest to youngest includes shonkinite, mesosyenite, syenite, quartz syenite, potassic granite, carbonatite, and late shonkinite dikes (Olson and others, 1954; Wooden and Miller, 1990; Haxel, 2005; Miller and others, 2007).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selle, J E

Attempts were made to apply the Kaufman method of calculating binary phase diagrams to the calculation of binary phase diagrams between the rare earths, actinides, and the refractory transition metals. Difficulties were encountered in applying the method to the rare earths and actinides, and modifications were necessary to provide accurate representation of known diagrams. To calculate the interaction parameters for rare earth-rare earth diagrams, it was necessary to use the atomic volumes for each of the phases: liquid, body-centered cubic, hexagonal close-packed, and face-centered cubic. Determination of the atomic volumes of each of these phases for each element is discussedmore » in detail. In some cases, empirical means were necessary. Results are presented on the calculation of rare earth-rare earth, rare earth-actinide, and actinide-actinide diagrams. For rare earth-refractory transition metal diagrams and actinide-refractory transition metal diagrams, empirical means were required to develop values for the enthalpy of vaporization for rare earth elements and values for the constant (C) required when intermediate phases are present. Results of using the values determined for each element are presented.« less

Geochemistry of host rocks in the Howards Pass district, Yukon-Northwest Territories, Canada: implications for sedimentary environments of Zn-Pb and phosphate mineralization

USGS Publications Warehouse

Slack, John F.; Falck, Hendrik; Kelley, Karen D.; Xue, Gabriel G.

2017-01-01

Detailed lithogeochemical data are reported here on early Paleozoic sedimentary rocks that host the large Howards Pass stratiform Zn-Pb deposits in Yukon-Northwest Territories. Redox-sensitive trace elements (Mo, Re, V, U) and Ce anomalies in members of the Duo Lake Formation record significant environmental changes. During the deposition of lower footwall units (Pyritic siliceous and Calcareous mudstone members), bottom waters were anoxic and sulphidic, respectively; these members formed in a marginal basin that may have become increasingly restricted with time. Relative to lower members, a major environmental change is proposed for deposition of the overlying Lower cherty mudstone member, which contains phosphorite beds up to ∼0.8 m thick in the upper part, near the base of the Zn-Pb deposits. The presence of these beds, together with models for modern phosphorite formation, suggests P input from an upwelling system and phosphorite deposition in an upper slope or outer shelf setting. The overlying Active mudstone member contains stratabound to stratiform Zn-Pb deposits within black mudstone and gray calcareous mudstone. Data for unmineralized black mudstone in this member indicate deposition under diverse redox conditions from suboxic to sulphidic. Especially distinctive in this member are uniformly low ratios of light to heavy rare earth elements that are unique within the Duo Lake Formation, attributed here to the dissolution of sedimentary apatite by downward-percolating acidic metalliferous brines. Strata that overlie the Active member (Upper siliceous mudstone member) consist mainly of black mudstone with thin (0.5–1.5 cm) laminae of fine-grained apatite, recording continued deposition on an upper slope or outer shelf under predominantly suboxic bottom waters. Results of this study suggest that exploration for similar stratiform sediment-hosted Zn-Pb deposits should include the outer parts of ancient continental margins, especially at and near stratigraphic transitions from marginal basin facies to overlying slope or shelf facies.

Analytical applications of condensed phosphoric acid-IV Iodometric determination of sulphur in sulphate and sulphide ores and minerals and other compounds after reduction with sodium hypophosphite and tin metal in condensed phosphoric acid.

PubMed

Mizoguchi, T; Ishii, H

1980-06-01

Sulphate in sulphate ores, e.g., alunite, anglesite, barytes, chalcanthite, gypsum, manganese sulphate ore, is reduced to hydrogen sulphide by the hypophosphite-tin metal-CPA method, if a slight modification is made. Sulphide ores, e.g., galena, sphalerite, are quantitatively decomposed with CPA alone to give hydrogen sulphide. Suitable reducing agents must be used for the quantitative recovery of hydrogen sulphide from pyrite, nickel sulphide, cobalt sulphide and cadmium sulphide, or elemental sulphur is liberated. Iodide must be used in the decomposition of chalcopyrite; the copper sulphide is too stable to be decomposed by CPA alone. Molybdenite is not decomposed in CPA even if reducing agents are added. The pretreatment methods for the determination of sulphur in sulphur oxyacids and elemental sulphur have also been investigated.

Rare-earth metal prices in the USA ca. 1960 to 1994

USGS Publications Warehouse

Hedrick, James B.

1997-01-01

Rare-earth metal prices were compiled from the late 1950s and early 1960s through 1994. Although commercial demand for rare-earth metals began in 1908, as the alloy mischmetal, commercial quantities of a wide range of individual rare-earth metals were not available until the late 1950s. The discovery of a large, high-grade rare-earth deposit at Mountain Pass. CA, USA, in 1949, was significant because it led to the production of commercial quantities or rare-earth elements that reduced prices and encouraged wider application of the materials. The availability of ore from Mountain Pass, and other large rare-earth deposits, especially those in Australia and China, has provided the world with abundant resources for rare-earth metal production. This availability, coupled with improved technology from Government and private-sector metallurgical research, has resulted in substantial decreases in rare-earth metal prices since the late 1950s and early 1960s. Price series for the individual rare-earth metals (except promethium) are quoted on a kilogram basis from the late 1950s and early 1960s through 1994. Prices are given in US dollars on an actual and constant dollar basis. Industrial and economic factors affecting prices during this time period are examined.

Rare-earth metal prices in the USA ca. 1960 to 1994

USGS Publications Warehouse

Hedrick, J.B.

1997-01-01

Rare-earth metal prices were compiled from the late 1950s and early 1960s through 1994. Although commercial demand for rare-earth metals began in 1908, as the alloy mischmetal, commercial quantities of a wide range of individual rare-earth metals were not available until the late 1950s. The discovery of a large, high-grade rare-earth deposit at Mountain Pass, CA, USA, in 1949, was significant because it led to the production of commercial quantities of rare-earth elements that reduced prices and encouraged wider application of the materials. The availability of ore from Mountain Pass, and other large rare-earth deposits, especially those in Australia and China, has provided the world with abundant resources for rare-earth metal production. This availability, coupled with improved technology from Government and private-sector metallurgical research, has resulted in substantial decreases in rare-earth metal prices since the late 1950s and early 1960s. Price series for the individual rare-earth metals (except promethium) are quoted on a kilogram basis from the late 1950s and early 1960s through 1994. Prices are given in US dollars on an actual and constant dollar basis. Industrial and economic factors affecting prices during this time period are examined.

A diagnostic challenge: a case of acrodermatitis enteropathica without hypozincemia and with maternal milk of low zinc level.

PubMed

Tatlican, Semih; Yamangokturk, Burcu; Eren, Cemile; Gulbahar, Ozlem; Eskioglu, Fatma

2010-01-01

Acrodermatitis enteropathica is a rare and distinct form of zinc deficiency with a requirement of life-long zinc supplementation and inherited in a recessive manner. Transient nutritional zinc deficiency is also a well known condition mimicking acrodermatitis enteropathica like skin changes in preterm and term infants who are generally breastfed with a low level of zinc containing milk. Here, a 4-month-old male, term and fully breastfed acrodermatitis enteropathica case without hypozincemia and with maternal milk of low zinc level is presented. © 2010 Wiley Periodicals, Inc.

The impact of cemented layers and hardpans on oxygen diffusivity in mining waste heaps: a field study of the Halsbrücke lead-zinc mine tailings (Germany).

PubMed

Kohfahl, Claus; Graupner, Torsten; Fetzer, Christian; Pekdeger, Asaf

2010-11-01

This article reports fibre-optic oxygen measurements on a reactive mine waste heap located in the polymetallic sulphide mine district of Freiberg in south-eastern Germany. The heaped material consists of sulphide-bearing tailings from a processing plant of a lead-zinc mine. Mine waste material was deposited in the water phase after separation of mining ores in a flotation process. The tailing impoundment is partly covered with coarse sand and topsoil. Oxygen profiles were monitored during one year at eleven locations showing different physical and mineralogical compositions. At each location a borehole was drilled where the optic sensors were installed at 2-5 different depths. After installation the oxygen profiles were monitored seven times during one year from 2006-2007 and three to five oxygen profiles at each location were obtained. Oxygen measurements were accompanied by physical, chemical and mineralogical data of the tailing material. Additionally, a detailed mineralogical profile was analysed at a location representative for the central part of the heap, where the cemented layers show lateral continuity. Results showed that cemented layers have a significant influence on natural attenuation of the toxic As and Pb species owing to their capacity of water retention. The measured oxygen profiles are controlled by the zone of active pyrite weathering as well as by the higher water content in the cemented layers which reduces gaseous atmospheric oxygen supply. In contrast, gypsum bearing hardpans detected at three other locations have no detectable influence on oxygen profiles. Furthermore, the grain size distribution was proved to have a major effect on oxygen diffusivity due to its control on the water saturation. Temporal changes of the oxygen profiles were only observed at locations with coarse sediment material indicating also an important advective part of gas flux. Copyright © 2010 Elsevier B.V. All rights reserved.

A monobromobimane-based assay to measure the pharmacokinetic profile of reactive sulphide species in blood

PubMed Central

Wintner, Edward A; Deckwerth, Thomas L; Langston, William; Bengtsson, Asa; Leviten, Dina; Hill, Paul; Insko, Michael A; Dumpit, Ronald; VandenEkart, Emily; Toombs, Christopher F; Szabo, Csaba

2010-01-01

Background and purpose: Hydrogen sulphide (H2S) is a labile, endogenous metabolite of cysteine, with multiple biological roles. The development of sulphide-based therapies for human diseases will benefit from a reliable method of quantifying H2S in blood and tissues. Experimental approach: Concentrations of reactive sulphide in saline and freshly drawn whole blood were quantified by reaction with the thio-specific derivatization agent monobromobimane, followed by reversed-phase fluorescence HPLC and/or mass spectrometry. In pharmacokinetic studies, male rats were exposed either to intravenous infusions of sodium sulphide or to H2S gas inhalation, and levels of available blood sulphide were measured. Levels of dissolved H2S/HS- were concomitantly measured using an amperometric sensor. Key results: Monobromobimane was found to rapidly and quantitatively derivatize sulphide in saline or whole blood to yield the stable small molecule sulphide dibimane. Extraction and quantification of this bis-bimane derivative were validated via reversed-phase HPLC separation coupled to fluorescence detection, and also by mass spectrometry. Baseline levels of sulphide in blood were in the range of 0.4–0.9 µM. Intravenous administration of sodium sulphide solution (2–20 mg·kg−1·h−1) or inhalation of H2S gas (50–400 ppm) elevated reactive sulphide in blood in a dose-dependent manner. Each 1 mg·kg−1·h−1 of sodium sulphide infusion into rats was found to be pharmacokinetically equivalent to approximately 30 ppm of H2S gas inhalation. Conclusions and implications: The monobromobimane derivatization method is a sensitive and reliable means to measure reactive sulphide species in whole blood. Using this method, we have established a bioequivalence between infused sodium sulphide and inhaled H2S gas. PMID:20590590

A monobromobimane-based assay to measure the pharmacokinetic profile of reactive sulphide species in blood.

PubMed

Wintner, Edward A; Deckwerth, Thomas L; Langston, William; Bengtsson, Asa; Leviten, Dina; Hill, Paul; Insko, Michael A; Dumpit, Ronald; VandenEkart, Emily; Toombs, Christopher F; Szabo, Csaba

2010-06-01

Hydrogen sulphide (H(2)S) is a labile, endogenous metabolite of cysteine, with multiple biological roles. The development of sulphide-based therapies for human diseases will benefit from a reliable method of quantifying H(2)S in blood and tissues. Concentrations of reactive sulphide in saline and freshly drawn whole blood were quantified by reaction with the thio-specific derivatization agent monobromobimane, followed by reversed-phase fluorescence HPLC and/or mass spectrometry. In pharmacokinetic studies, male rats were exposed either to intravenous infusions of sodium sulphide or to H(2)S gas inhalation, and levels of available blood sulphide were measured. Levels of dissolved H(2)S/HS(-) were concomitantly measured using an amperometric sensor. Monobromobimane was found to rapidly and quantitatively derivatize sulphide in saline or whole blood to yield the stable small molecule sulphide dibimane. Extraction and quantification of this bis-bimane derivative were validated via reversed-phase HPLC separation coupled to fluorescence detection, and also by mass spectrometry. Baseline levels of sulphide in blood were in the range of 0.4-0.9 microM. Intravenous administration of sodium sulphide solution (2-20 mg x kg(-1) x h(-1)) or inhalation of H(2)S gas (50-400 ppm) elevated reactive sulphide in blood in a dose-dependent manner. Each 1 mg x kg(-1) x h(-1) of sodium sulphide infusion into rats was found to be pharmacokinetically equivalent to approximately 30 ppm of H(2)S gas inhalation. The monobromobimane derivatization method is a sensitive and reliable means to measure reactive sulphide species in whole blood. Using this method, we have established a bioequivalence between infused sodium sulphide and inhaled H(2)S gas.

China's rare-earth industry

USGS Publications Warehouse

Tse, Pui-Kwan

2011-01-01

Introduction China's dominant position as the producer of over 95 percent of the world output of rare-earth minerals and rapid increases in the consumption of rare earths owing to the emergence of new clean-energy and defense-related technologies, combined with China's decisions to restrict exports of rare earths, have resulted in heightened concerns about the future availability of rare earths. As a result, industrial countries such as Japan, the United States, and countries of the European Union face tighter supplies and higher prices for rare earths. This paper briefly reviews China's rare-earth production, consumption, and reserves and the important policies and regulations regarding the production and trade of rare earths, including recently announced export quotas. The 15 lanthanide elements-lanthanum, cerium, praseodymium, neodymium, promethium, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium (atomic numbers 57-71)-were originally known as the rare earths from their occurrence in oxides mixtures. Recently, some researchers have included two other elements-scandium and yttrium-in their discussion of rare earths. Yttrium (atomic number 39), which lies above lanthanum in transition group III of the periodic table and has a similar 3+ ion with a noble gas core, has both atomic and ionic radii similar in size to those of terbium and dysprosium and is generally found in nature with lanthanides. Scandium (atomic number 21) has a smaller ionic radius than yttrium and the lanthanides, and its chemical behavior is intermediate between that of aluminum and the lanthanides. It is found in nature with the lanthanides and yttrium. Rare earths are used widely in high-technology and clean-energy products because they impart special properties of magnetism, luminescence, and strength. Rare earths are also used in weapon systems to obtain the same properties.

Leaching behavior of rare earth elements in Fort Union lignite coals of North America

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laudal, Daniel A.; Benson, Steven A.; Addleman, Raymond Shane

Rare earth elements are crucial materials in an incredible array of consumer goods, energy system components and military defense applications. However, the global production and entire value chain for rare earth elements is dominated by China, with the U.S. currently 100% import reliant for these critical materials. Traditional mineral ores including those previously mined in the U.S., however, have several challenges. Chief among these is that the content of the most critical and valuable of the rare earths are deficient, making mining uneconomical. Further, the supply of these most critical rare earths is nearly 100% produced in China from amore » single resource that is only projected to last another 10 to 20 years. The U.S. currently considers the rare earths market an issue of national security. It is imperative that alternative domestic sources of rare earths be identified and methods developed to produce them. Recently, coal and coal byproducts have been identified as one of these promising alternative resources. This paper details the results of a study on characterization of North Dakota lignite and lignite-related feedstocks as an assessment of their feasibility for rare earth element recovery. The abundance, distribution and modes of occurrence of the rare earth elements in the samples collected were determined in this initial study to inform the selection of appropriate extraction and concentration methods to recover the rare earth elements. Materials investigated include the lignite coals, clay-rich sediments associated with the coal seams, and materials associated with a lignite beneficiation system and power plant. The results show that high rare earth element levels exist both in lignite coals and associated sediments. The form of the rare earth elements in the clay materials is primarily as ultra-fine mineral grains. In the lignite coals, approximately 80-95% of the rare earths content is organically associated, primarily as coordination complexes.« less

Rare earths, the lanthanides, yttrium and scandium

USGS Publications Warehouse

Hedrick, J.B.

2006-01-01

In 2005, rare earths were not mined in the United States. The major supplier, Molycorp, continued to maintain a large stockpile of rare-earth concentrates and compounds. Consumption decreased of refined rare-earth products. The United States remained a major importer and exporter of rare earths in 2005. During the same period, yttrium was not mined or refined in the US. Hence, supply of yttrium compounds for refined yttrium products came from China, France and Japan. Scandium was not also mined. World production was primarily in China, Russia and Ukraine. Demand for rare earths in 2006 is expected to be closely tied to economic conditions in the US.

Replacing critical rare earth materials in high energy density magnets

NASA Astrophysics Data System (ADS)

McCallum, R. William

2012-02-01

High energy density permanent magnets are crucial to the design of internal permanent magnet motors (IPM) for hybride and electric vehicles and direct drive wind generators. Current motor designs use rare earth permanent magnets which easily meet the performance goals, however, the rising concerns over cost and foreign control of the current supply of rare earth resources has motivated a search for non-rare earth based permanent magnets alloys with performance metrics which allow the design of permanent magnet motors and generators without rare earth magnets. This talk will discuss the state of non-rare-earth permanent magnets and efforts to both improve the current materials and find new materials. These efforts combine first principles calculations and meso-scale magnetic modeling with advance characterization and synthesis techniques in order to advance the state of the art in non rare earth permanent magnets. The use of genetic algorithms in first principle structural calculations, combinatorial synthesis in the experimental search for materials, atom probe microscopy to characterize grain boundaries on the atomic level, and other state of the art techniques will be discussed. In addition the possibility of replacing critical rare earth elements with the most abundant rare earth Ce will be discussed.

Ames Lab 101: Rare Earths

ScienceCinema

Gschneidner, Karl

2017-12-11

"Mr. Rare Earth," Ames Laboratory scientist Karl Gschneidner Jr., explains the importance of rare-earth materials in many of the technologies we use today -- ranging from computers to hybrid cars to wind turbines. Gschneidner is a world renowned rare-earths expert at the U.S. Department of Energy's Ames Laboratory.

Environmental Defects And Economic Impact On Global Market Of Rare Earth Metals

NASA Astrophysics Data System (ADS)

Charalampides, G.; Vatalis, K.; Karayannis, V.; Baklavaridis, A.

2016-11-01

Rare earth elements include the 14 lanthanides as well as lanthanium and often yttrium. Actually, most of them are not very rare and occur widely dispersed in a variety of rocks. Rare earth metals are vital to some of the world's faster growing industries: catalysts, Nd-magnets, ceramics, glass, metallurgy, battery alloys, electronics and phosphors. Worldwide, the main countries for distribution of rare earths deposits include China, USA, Russia, Brasil, India, Australia, Greenland and Malaysia. The mining and processing of rare earth metals usually result in significant environmental defects. Many deposits are associated with high concentrations of radioactive elements such as uranium and thorium, which requires separate treatment and disposal. The accumulation of rare earth elements in soils has occurred due to pollution caused by the exploitation of rare earth resources and the wide use of rare earths as fertilizers in agriculture. This accumulation has a toxic effect on the soil microfauna community. However, there are large differences in market prices due to the degree of purity determined by the specifications in the applications. The main focus of this article is to overview Rare Earth Metals’ overall impact on global economy and their environmental defects on soils during processing techniques and as they are used as fertilizers.

Mother Lode: The Untapped Rare Earth Mineral Resources of Vietnam

DTIC Science & Technology

2013-11-01

Library of Congress, Congressional Research Service. Rare Earth Elements: The Global Supply Chain, 4. 14 Tse , Pui-Kwan. China’s Rare-Earth Industry...U.S. Geological Survey Open-File Report 2011–1042, 2. Figure 2. Global REO production, 1960-2011. Source: Tse , Pui-Kwan. China’s Rare-Earth...3 compiled from three sources: Tse , Pui-Kwan. China’s Rare-Earth Industry: U.S. Geological Survey Open-File Report 2011–1042, 4; Areddy, James T

40 CFR 721.6005 - Rare earth phosphate (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Rare earth phosphate (generic). 721... Substances § 721.6005 Rare earth phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as rare earth phophate (PMNs P-99...

40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Rare Earth Metals Subcategory § 421.270 Applicability: Description of the primary rare earth metals subcategory. The provisions of this subpart are applicable to discharges resulting from the...

40 CFR 721.6005 - Rare earth phosphate (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Rare earth phosphate (generic). 721... Substances § 721.6005 Rare earth phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as rare earth phophate (PMNs P-99...

40 CFR 721.6005 - Rare earth phosphate (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Rare earth phosphate (generic). 721... Substances § 721.6005 Rare earth phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as rare earth phophate (PMNs P-99...

40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Rare Earth Metals Subcategory § 421.270 Applicability: Description of the primary rare earth metals subcategory. The provisions of this subpart are applicable to discharges resulting from the...

40 CFR 721.6005 - Rare earth phosphate (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Rare earth phosphate (generic). 721... Substances § 721.6005 Rare earth phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as rare earth phophate (PMNs P-99...

40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Rare Earth Metals Subcategory § 421.270 Applicability: Description of the primary rare earth metals subcategory. The provisions of this subpart are applicable to discharges resulting from the...

40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Rare Earth Metals Subcategory § 421.270 Applicability: Description of the primary rare earth metals subcategory. The provisions of this subpart are applicable to discharges resulting from the...

40 CFR 421.270 - Applicability: Description of the primary rare earth metals subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... primary rare earth metals subcategory. 421.270 Section 421.270 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Rare Earth Metals Subcategory § 421.270 Applicability: Description of the primary rare earth metals subcategory. The provisions of this subpart are applicable to discharges resulting from the...

40 CFR 721.6005 - Rare earth phosphate (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Rare earth phosphate (generic). 721... Substances § 721.6005 Rare earth phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as rare earth phophate (PMNs P-99...

Mineralogy and chemistry of massive sulfide deposits from the Juan de Fuca Ridge.

USGS Publications Warehouse

Koski, R.A.; Clague, D.A.; Oudin, E.

1984-01-01

Two types of massive sulphide were dredged from one of the six vent sites located in the axial valley of the southern Juan de Fuca ridge. Type A samples are angular slabs of dark grey Zn-rich sulphide with interlayers and a thin, partly-oxidized crust of Fe-sulphide. These layered sulphide aggregates appear to be fragments of a sulphide wall enclosing an active hydrothermal vent. The outer sulphide wall is composed of colloform Fe sulphide and Fe-poor sphalerite deposited under low-T conditions when sea-water and hydrothermal fluid mix above the discharge point. Inside the wall the intensifying hydrothermal sytem deposits a higher-T assemblage of granular Fe-rich sphalerite, wurtzite, pyrite and minor Cu-Fe sulphide. Type B sulphide samples are sub-rounded, spongy-textured fragments composed almost entirely of dendritic aggregates of pale Fe-poor colloform sphalerite and opaline silica. This type of sulphide is deposited in settings peripheral to sites of focused discharge and in open spaces by moderate- to low-T fluid discharging at a slow but variable rate; the fluid becomes increasingly oxidizing, resulting in late-stage deposits of hematite, baryte and sulphur.-L.di H.

Antifungal activity of wide band gap Thioglycolic acid capped ZnS:Mn semiconductor nanoparticles against some pathogenic fungi.

PubMed

Ibrahim, Isam M; Ali, Iftikhar M; Dheeb, Batol Imran; Abas, Qayes A; Asmeit Ramizy; Eisa, M H; Aljameel, A I

2017-04-01

The manganese doped zinc sulfide nanoparticles were synthesized by simple aqueous chemical reaction of manganese chloride, zinc acetate and thioacitamide in aqueous solution. Thioglycolic acid is used as capping agent for controlling the nanoparticle size. The main advantage of the ZnS:Mn nanoparticles of diameter ~2.73nm is that the sample is prepared by using non-toxic precursors in a cost effective and eco-friendly way. The structural, morphological and chemical composition of the nanoparticles have been investigated by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) with energy dispersion spectroscopy (EDS) and Fourier transform infrared (FTIR) spectroscopy. The nanosize of the prepared nanoparticles was elucidated by Scanning Electron Microscopy (SEM). FTIR result ensures that Thioglycolic acid is well bonded on the surface of ZnS:Mn NPs. The antifungal effects of Thioglycolic acid capped ZnS:Mn nanoparticles exhibited a potent antifungal activity against tested fungal strains, so deserving further investigation for clinical applications. The antifungal property of manganese doped zinc sulphide nanoparticles is attributed to the generation of reactive oxygen species due to the interaction of nanoparticles with water. Additionally, the presence of Zn and S in the zone of inhibition area leads to perturbation of fungi cell membranes resulting in growth inhibition. Copyright © 2016 Elsevier B.V. All rights reserved.

Mineral resource of the month: rare earths

USGS Publications Warehouse

Hedrick, James B.

2004-01-01

As if classified as a top-secret project, the rare earths have been shrouded in secrecy. The principal ore mineral of the group, bastnäsite, rarely appears in the leading mineralogy texts. The long names of the rare-earth elements and some unusual arrangements of letters, many Scandinavian in origin, may have intimidated even those skilled in phonics. Somewhat obscurely labeled, the rare earths are neither rare nor earths (the historical term for oxides). They are a relatively abundant group of metallic elements that occur in nature as nonmetallic compounds and have hundreds of commercial applications.

The simulation of CZTS solar cell for performance improvement

NASA Astrophysics Data System (ADS)

Kumar, Atul; Thakur, Ajay D.

2018-05-01

A Copper-Zinc-Tin-Sulphide (CZTS) based solar cell of Mo/CZTS/CdS/ZnO is simulated using SCAPS. Quantum efficiency and IV curve of the simulated output of CZTS solar cell is mapped with highest efficiency reported in literature for CZTS solar cell. A modification in back contact thus shottky barrier, spike type band alignment at the CZTS-n type layer junction and higher electron mobility (owing to alkali doping in CZT)S are implement in simulation of CZTS solar cell. An improvement in the solar cell efficiency compared to the standard cell configuration of Mo/CZTS/CdS/ZnO is found. CZTS is plagued with low Voc and low FF which can be increased by optimization as suggested in paper.

Medicinal exploitation of inorganic substances in the Levant in the Medieval and early Ottoman periods.

PubMed

Lev, Efraim

2002-11-01

Various minerals, metals, clays, and rocks were among the natural medicinal substances used by physicians and pharmacists in early times in different cultures, for example, the ancient civilizations of Egypt and Mesopotamia. Classical physicians such as Hippocrates and Dioscorides mention tens of inorganic medicinal substances in their writings. Many references to minerals and chemicals are also found in the Muslim medical literature of the Eastern and Western Caliphates. The historical research presented in this article focuses on the inorganic substances applied as remedies by the medieval and early Ottoman (7th-17th) inhabitants of the Levant. The article is based upon a literature review covering tens of different historical sources, from the medieval and early Ottoman periods. Relevant information was found in the works of physicians such as al-Tamimi, Benevenutus, Ibn al-Baytar, Daud al-Antaki, and Hayyim Vital. The research revealed evidences of the medicinal uses of fifteen inorganic substances: Alum, Arsenic, Sulphide, Asphalt, Jew's stone, Earth sp., Galena, Haematite, iron, Lead, Pyrite, Salt, Sulphur, Thermal water, Green Vitriol, and Zinc. Inorganic materials comprise 5.2% of the list of medicinal substances. The geographic origin of most of these substances is the Levant, in which two geo-historical centers have been recorded: the Rift Valley and the northern region of the Levant, including upper Galilee, Mount Lebanon and Mount Hermon. A notable tendency to use these substances for treating diseases of the skin, the eyes, the sexual organs, and haemorrhoids was detected.

77 FR 51046 - Certain Sintered Rare Earth Magnets, Methods of Making Same and Products Containing Same; Notice...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-23

... INTERNATIONAL TRADE COMMISSION [Docket No. 2908] Certain Sintered Rare Earth Magnets, Methods of... Certain Sintered Rare Earth Magnets, Methods of Making Same and Products Containing Same, DN 2908; the... importation, and the sale within the United States after importation of certain sintered rare earth magnets...

77 FR 58578 - Certain Sintered Rare Earth Magnets, Methods of Making Same and Products Containing Same...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-21

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-855] Certain Sintered Rare Earth Magnets... importation of certain sintered rare earth magnets, methods of making same and products containing same by... importation of certain sintered rare earth magnets, methods of making same and products containing same that...

Global warming enhances sulphide stress in a key seagrass species (NW Mediterranean).

PubMed

García, Rosa; Holmer, Marianne; Duarte, Carlos M; Marbà, Núria

2013-12-01

The build-up of sulphide concentrations in sediments, resulting from high inputs of organic matter and the mineralization through sulphate reduction, can be lethal to the benthos. Sulphate reduction is temperature dependent, thus global warming may contribute to even higher sulphide concentrations and benthos mortality. The seagrass Posidonia oceanica is very sensitive to sulphide stress. Hence, if concentrations build up with global warming, this key Mediterranean species could be seriously endangered. An 8-year monitoring of daily seawater temperature, the sulphur isotopic signatures of water (δ(34)S(water)), sediment (δ(34)SCRS ) and P. oceanica leaf tissue (δ(34)S(leaves)), along with total sulphur in leaves (TS(leaves)) and annual net population growth along the coast of the Balearic archipelago (Western Mediterranean) allowed us to determine if warming triggers P. oceanica sulphide stress and constrains seagrass survival. From the isotopic S signatures, we estimated sulphide intrusion into the leaves (F(sulphide)) and sulphur incorporation into the leaves from sedimentary sulphides (SS(leaves)). We observed lower δ(34)S(leaves), higher F(sulphide) and SS(leaves) coinciding with a 6-year period when two heat waves were recorded. Warming triggered sulphide stress as evidenced by the negative temperature dependence of δ(34)S(leaves) and the positive one of F(sulphide), TS(leaves) and SS(leaves). Lower P. oceanica net population growth rates were directly related to higher contents of TS(leaves). At equivalent annual maximum sea surface water temperature (SST(max)), deep meadows were less affected by sulphide intrusion than shallow ones. Thus, water depth acts as a protecting mechanism against sulphide intrusion. However, water depth would be insufficient to buffer seagrass sulphide stress triggered by Mediterranean seawater summer temperatures projected for the end of the 21st century even under scenarios of moderate greenhouse gas emissions, A1B. Mediterranean warming, therefore, is expected to enhance P. oceanica sulphide stress, and thus compromise the survival of this key habitat along its entire depth distribution range. © 2013 John Wiley & Sons Ltd.

Carbonatite and alkaline intrusion-related rare earth element deposits–A deposit model

USGS Publications Warehouse

Verplanck, Philip L.; Van Gosen, Bradley S.

2011-01-01

The rare earth elements are not as rare in nature as their name implies, but economic deposits with these elements are not common and few deposits have been large producers. In the past 25 years, demand for rare earth elements has increased dramatically because of their wide and diverse use in high-technology applications. Yet, presently the global production and supply of rare earth elements come from only a few sources. China produces more than 95 percent of the world's supply of rare earth elements. Because of China's decision to restrict exports of these elements, the price of rare earth elements has increased and industrial countries are concerned about supply shortages. As a result, understanding the distribution and origin of rare earth elements deposits, and identifying and quantifying our nation's rare earth elements resources have become priorities. Carbonatite and alkaline intrusive complexes, as well as their weathering products, are the primary sources of rare earth elements. The general mineral deposit model summarized here is part of an effort by the U.S. Geological Survey's Mineral Resources Program to update existing models and develop new descriptive mineral deposit models to supplement previously published models for use in mineral-resource and mineral-environmental assessments. Carbonatite and alkaline intrusion-related REE deposits are discussed together because of their spatial association, common enrichment in incompatible elements, and similarities in genesis. A wide variety of commodities have been exploited from carbonatites and alkaline igneous rocks, such as rare earth elements, niobium, phosphate, titanium, vermiculite, barite, fluorite, copper, calcite, and zirconium. Other enrichments include manganese, strontium, tantalum, thorium, vanadium, and uranium.

Effects of rare-earth co-doping on the local structure of rare-earth phosphate glasses using high and low energy X-ray diffraction.

PubMed

Cramer, Alisha J; Cole, Jacqueline M; FitzGerald, Vicky; Honkimaki, Veijo; Roberts, Mark A; Brennan, Tessa; Martin, Richard A; Saunders, George A; Newport, Robert J

2013-06-14

Rare-earth co-doping in inorganic materials has a long-held tradition of facilitating highly desirable optoelectronic properties for their application to the laser industry. This study concentrates specifically on rare-earth phosphate glasses, (R2O3)x(R'2O3)y(P2O5)(1-(x+y)), where (R, R') denotes (Ce, Er) or (La, Nd) co-doping and the total rare-earth composition corresponds to a range between metaphosphate, RP3O9, and ultraphosphate, RP5O14. Thereupon, the effects of rare-earth co-doping on the local structure are assessed at the atomic level. Pair-distribution function analysis of high-energy X-ray diffraction data (Q(max) = 28 Å(-1)) is employed to make this assessment. Results reveal a stark structural invariance to rare-earth co-doping which bears testament to the open-framework and rigid nature of these glasses. A range of desirable attributes of these glasses unfold from this finding; in particular, a structural simplicity that will enable facile molecular engineering of rare-earth phosphate glasses with 'dial-up' lasing properties. When considered together with other factors, this finding also demonstrates additional prospects for these co-doped rare-earth phosphate glasses in nuclear waste storage applications. This study also reveals, for the first time, the ability to distinguish between P-O and P[double bond, length as m-dash]O bonding in these rare-earth phosphate glasses from X-ray diffraction data in a fully quantitative manner. Complementary analysis of high-energy X-ray diffraction data on single rare-earth phosphate glasses of similar rare-earth composition to the co-doped materials is also presented in this context. In a technical sense, all high-energy X-ray diffraction data on these glasses are compared with analogous low-energy diffraction data; their salient differences reveal distinct advantages of high-energy X-ray diffraction data for the study of amorphous materials.

Hydrogen sulphide removal from corroding concrete: comparison between surface removal rates and biomass activity.

PubMed

Jensen, H S; Nielsen, A H; Lens, P N L; Hvitved-Jacobsen, T; Vollertsen, J

2009-11-01

Corrosion of concrete sewer pipes caused by hydrogen sulphide is a problem in many sewer networks. The mechanisms of production and fate of hydrogen sulphide in the sewer biofilms and wastewater as well as its release to the sewer atmosphere are largely understood. In contrast, the mechanisms of the uptake of hydrogen sulphide on the concrete surfaces and subsequent concrete corrosion are basically unknown. To shed light on these mechanisms, the uptake of hydrogen sulphide from a sewer gas phase was compared to the biological hydrogen sulphide removal potential of the concrete corrosion products. The results showed that both microbial degradation at and sorption to the concrete surfaces were important for the uptake of hydrogen sulphide on the concrete surfaces.

Rare Earths; The Fraternal Fifteen (Rev.)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gschneidner, Jr., Karl A.

1966-01-01

Rare earths are a set of 15 elements: lanthanum, cerium, praseodymium, neodymium, promethium, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. They are not rare and not earths; they are metals and quite abundant. They are studied to develop commercial products which are beneficial to mankind, and because some rare earths are important to fission products.

75 FR 25293 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Rare Earth...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-07

... Production Act of 1993--Rare Earth Industry and Technology Association Notice is hereby given that, on March..., 15 U.S.C. 4301 et seq. (``the Act''), the Rare Earth Technology Consortium (``RETC'') has filed..., the identities of the parties to the venture are: Rare Earth Industry and Tecimology Association...

40 CFR 721.10550 - Rare earth salt of a carboxylic acid (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Rare earth salt of a carboxylic acid... Specific Chemical Substances § 721.10550 Rare earth salt of a carboxylic acid (generic). (a) Chemical... as rare earth salt of a carboxylic acid (PMN P-05-324) is subject to reporting under this section for...

40 CFR 721.10550 - Rare earth salt of a carboxylic acid (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Rare earth salt of a carboxylic acid... Specific Chemical Substances § 721.10550 Rare earth salt of a carboxylic acid (generic). (a) Chemical... as rare earth salt of a carboxylic acid (PMN P-05-324) is subject to reporting under this section for...

PROCESS FOR SEPARATING AMERICIUM AND CURIUM FROM RARE EARTH ELEMENTS

DOEpatents

Baybarz, R.D.; Lloyd, M.H.

1963-02-26

This invention relates to methods of separating americium and curium values from rare earth values. In accordance with the invention americium, curium, and rare earth values are sorbed on an anion exchange resin. A major portion of the rare earth values are selectively stripped from the resin with a concentrated aqueous solution of lithium chloride, and americium, curium, and a minor portion of rare earth values are then stripped from the resin with a dilute aqueous solution of lithium chloride. The americium and curium values are further purified by increasing the concentration of lithium chloride in the solution to at least 8 molar and selectively extracting rare earth values from the resulting solution with a monoalkylphosphoric acid. (AEC)

Electronic Characteristics of Rare Earth Doped GaN Schottky Diodes

DTIC Science & Technology

2013-03-21

REPORT TYPE Master’s Thesis 3. DATES COVERED (From – To) 04 Sep 2011 - Mar 2013 4. TITLE AND SUBTITLE ELECTRONIC CHARACTERISTICS OF RARE EARTH ...ELECTRONIC CHARACTERISTICS OF RARE EARTH DOPED GaN SCHOTTKY DIODES THESIS Aaron B. Blanning...United States. AFIT-ENP-13-M-03 Electronic Characteristics of Rare Earth Doped GaN Schottky Diodes THESIS Presented to the Faculty

Antibacterial, Antifungal and Nematicidal Activities of Rare Earth Ions.

PubMed

Wakabayashi, Tokumitsu; Ymamoto, Ayumi; Kazaana, Akira; Nakano, Yuta; Nojiri, Yui; Kashiwazaki, Moeko

2016-12-01

Despite the name, rare earth elements are relatively abundant in soil. Therefore, these elements might interact with biosphere during the history of life. In this study, we have examined the effect of rare earth ions on the growth of bacteria, fungi and soil nematode. All rare earth ions, except radioactive promethium that we have not tested, showed antibacterial and antifungal activities comparable to that of copper ions, which is widely used as antibacterial metals in our daily life. Rare earth ions also have nematicidal activities as they strongly perturb the embryonic development of the nematode, Caenorhabditis elegans. Interestingly, the nematicidal activity increased with increasing atomic number of lanthanide ions. Since the rare earth ions did not show high toxicity to the human lymphoblastoid cell line or even stimulate the growth of the cultured cells at 1 mM, it raised the possibility that we can substitute rare earth elements for the antibacterial metals usually used because of their safety.

Google Earth locations of USA and seafloor hydrothermal vents with associated rare earth element data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrew Fowler

Google Earth .kmz files that contain the locations of geothermal wells and thermal springs in the USA, and seafloor hydrothermal vents that have associated rare earth element data. The file does not contain the actual data, the actual data is available through the GDR website in two tier 3 data sets entitled "Compilation of Rare Earth Element Analyses from US Geothermal Fields and Mid Ocean Ridge (MOR) Hydrothermal Vents" and "Rare earth element content of thermal fluids from Surprise Valley, California"

RECONDITIONING FUEL ELEMENTS

DOEpatents

Brandt, H.L.

1962-02-20

A process is given for decanning fuel elements that consist of a uranium core, an intermediate section either of bronze, silicon, Al-Si, and uranium silicide layers or of lead, Al-Si, and uranium silicide layers around said core, and an aluminum can bonded to said intermediate section. The aluminum can is dissolved in a solution of sodium hydroxide (9 to 20 wt%) and sodium nitrate (35 to 12 wt %), and the layers of the intermediate section are dissolved in a boiling sodium hydroxide solution of a minimum concentration of 50 wt%. (AEC) A method of selectively reducing plutonium oxides and the rare earth oxides but not uranium oxides is described which comprises placing the oxides in a molten solvent of zinc or cadmium and then adding metallic uranium as a reducing agent. (AEC)

IDAHO WILDERNESS, IDAHO.

USGS Publications Warehouse

Cater, Fred W.; Weldin, R.D.

1984-01-01

Mineral surveys conducted in the Idaho Wilderness identified 28 areas with probable or substantiated mineral-resource potential, and 5 mines with demonstrated or inferred resources. Metals including gold, silver, copper, lead, zinc, and tungsten, have been extracted from deposits inside the wilderness. Current studies indicate additional areas of probable mineral-resource potential for gold, tungsten, mercury, rare-earth elements, and base metals related to intrusive rocks that follow structures formed by cauldron subsidence. These on-going studies also indicate that there is probable and substantiated resource potential for cobalt with copper, silver, and gold in the Precambrian rocks in the northeastern part of the wilderness in a geologic environment similar to that of the Blackbird mine that lies outside the area. The nature of the geologic terrane precludes the potential for organic fuels.

Rare earth fluoride nano-/microstructures: hydrothermal synthesis, luminescent properties and applications.

PubMed

Zhao, Qian; Xu, Zhenhe; Sun, Yaguang

2014-02-01

Rare earth fluoride materials have attracted wide interest and come to the forefront in nanophotonics due to their distinct electrical, optical and magnetic properties as well as their potential applications in diverse fields such as optical telecommunication, lasers, biochemical probes, infrared quantum counters, and medical diagnostics. This review presents a comprehensive overview of the flourishing field of rare earth fluorides materials in the past decade. We summarize the recent research progress on the preparation, morphology, luminescent properties and application of rare earth fluoride-based luminescent materials by hydrothermal systems. Various rare earth fluoride materials are obtained by fine-tuning of experimental conditions, such as capping agents, fluoride source, acidity, temperature and reaction time. The controlled morphology, luminescent properties and application of the rare earth fluorides are briefly discussed with typical examples.

Phase stable rare earth garnets

DOEpatents

Kuntz, Joshua D.; Cherepy, Nerine J.; Roberts, Jeffery J.; Payne, Stephen A.

2013-06-11

A transparent ceramic according to one embodiment includes a rare earth garnet comprising A.sub.hB.sub.iC.sub.jO.sub.12, where h is 3.+-.10%, i is 2.+-.10%, and j is 3.+-.10%. A includes a rare earth element or a mixture of rare earth elements, B includes at least one of aluminum, gallium and scandium, and C includes at least one of aluminum, gallium and scandium, where A is at a dodecahedral site of the garnet, B is at an octahedral site of the garnet, and C is at a tetrahedral site of the garnet. In one embodiment, the rare earth garment has scintillation properties. A radiation detector in one embodiment includes a transparent ceramic as described above and a photo detector optically coupled to the rare earth garnet.

Superconductivity achieved at over liquid nitrogen temperature by (mixed rare earths)-Ba-Cu oxides

NASA Astrophysics Data System (ADS)

Kishio, Kohji; Kuwahara, Kazuyuki; Kitazawa, Koichi; Fueki, Kazuo; Nakamura, Osamu

1987-05-01

Superconducting oxides were fabricated by reaction of powders of BaCO3, CuO and mixed rare earth (RE) carbonates at compositions expressed as (RE)1Ba2Cu3O(9-y). Two types of incompletely separated raw materials of mixed rare earths, namely, heavy rare earths (HRE) and medium rare earths (MRE), were examined. The zero-resistivity critical temperatures were observed at 92.5 K for the (HRE)-Ba-Cu-O and 85.0 K for the (MRE)-Ba-Cu-O systems, respectively, both of which were well above the boiling point of liquid nitrogen.

Distribution behavior of uranium, neptunium, rare-earth elements ( Y, La, Ce, Nd, Sm, Eu, Gd) and alkaline-earth metals (Sr,Ba) between molten LiClKCI eutectic salt and liquid cadmium or bismuth

NASA Astrophysics Data System (ADS)

Kurata, M.; Sakamura, Y.; Hijikata, T.; Kinoshita, K.

1995-12-01

Distribution coefficients of uranium neptunium, eight rare-earth elements (Y, La, Ce, Pr, Nd, Sm, Eu and Gd) and two alkaline-earth metals (Sr and Ba) between molten LiCl-KCI eutectic salt and either liquid cadmium or bismuth were measured at 773 K. Separation factors of trivalent rare-earth elements to uranium or neptunium in the LiCl-KCl/Bi system were by one or two orders of magnitude larger than those in the LiCl-KCl/Cd system. On the contrary, the separation factors of alkaline-earth metals and divalent rare-earth elements to trivalent rare-earth elements were by one or two orders of magnitude smaller in the LiCl-KCl/Bi system.

Replacement and Original Magnet Engineering Options (ROMEOs): A European Seventh Framework Project to Develop Advanced Permanent Magnets Without, or with Reduced Use of, Critical Raw Materials

NASA Astrophysics Data System (ADS)

Mcguiness, P.; Akdogan, O.; Asali, A.; Bance, S.; Bittner, F.; Coey, J. M. D.; Dempsey, N. M.; Fidler, J.; Givord, D.; Gutfleisch, O.; Katter, M.; Le Roy, D.; Sanvito, S.; Schrefl, T.; Schultz, L.; Schwöbl, C.; Soderžnik, M.; Šturm, S.; Tozman, P.; Üstüner, K.; Venkatesan, M.; Woodcock, T. G.; Žagar, K.; Kobe, S.

2015-06-01

The rare-earth crisis, which peaked in the summer of 2011 with the prices of both light and heavy rare earths soaring to unprecedented levels, brought about the widespread realization that the long-term availability and price stability of rare earths could not be guaranteed. This triggered a rapid response from manufacturers involved in rare earths, as well as governments and national and international funding agencies. In the case of rare-earth-containing permanent magnets, three possibilities were given quick and serious consideration: (I) increased recycling of devices containing rare earths; (II) the search for new, mineable, rare-earth resources beyond those in China; and (III) the development of high-energy-product permanent magnets with little or no rare-earth content used in their manufacture. The Replacement and Original Magnet Engineering Options (ROMEO) project addresses the latter challenge using a two-pronged approach. With its basis on work packages that include materials modeling and advanced characterization, the ROMEO project is an attempt to develop a new class of novel permanent magnets that are free of rare earths. Furthermore, the project aims to minimize rare-earth content, particularly heavy-rare-earth (HRE) content, as much as possible in Nd-Fe-B-type magnets. Success has been achieved on both fronts. In terms of new, rare-earth-free magnets, a Heusler alloy database of 236,945 compounds has been narrowed down to approximately 20 new compounds. Of these compounds, Co2MnTi is expected to be a ferromagnet with a high Curie temperature and a high magnetic moment. Regarding the reduction in the amount of rare earths, and more specifically HREs, major progress is seen in electrophoretic deposition as a method for accurately positioning the HRE on the surface prior to its diffusion into the microstructure. This locally increases the coercivity of the rather small Nd-Fe-B-type magnet, thereby substantially reducing the dependence on the HREs Dy and Tb, two of the most critical raw materials identified by the European Commission. Overall, the ROMEO project has demonstrated that rapid progress can be achieved when experts in a specific area are brought together to focus on a particular challenge. With more than half a year of the ROMEO project remaining, further progress and additional breakthroughs can be expected.

Methods for preparation of nanocrystalline rare earth phosphates for lighting applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comanzo, Holly Ann; Manoharan, Mohan; Martins Loureiro, Sergio Paulo

Disclosed here are methods for the preparation of optionally activated nanocrystalline rare earth phosphates. The optionally activated nanocrystalline rare earth phosphates may be used as one or more of quantum-splitting phosphor, visible-light emitting phosphor, vacuum-UV absorbing phosphor, and UV-emitting phosphor. Also disclosed herein are discharge lamps comprising the optionally activated nanocrystalline rare earth phosphates provided by these methods.

Secondary overprinting of S-Se-Te signatures in the Earth's mantle: Implications for the Late Veneer

NASA Astrophysics Data System (ADS)

Koenig, S.; Luguet, A.; Lorand, J.; Pearson, D.

2013-12-01

Sulphur, Selenium and Tellurium are both chalcophile and highly siderophile elements (HSE) with near-chondritic ratios and absolute abundances in the terrestrial mantle that exceed those predicted by core-mantle differentiation[1]. These 'excess' HSE abundances have been attributed to addition of ca. 0.5% of chondrite-like material that hit the Earth in its accretionary stage between 4 to 3.8 billion years ago after core-mantle differentiation (Late Veneer[2]). Therefore, like other HSE, S, Se and Te are considered potential tracers for the composition of the Late Veneer, provided that their bulk silicate Earth abundances are properly constrained. In contrast to ca. 250 ppm S, Se and Te are ultra-trace elements in the terrestrial mantle. Like all HSE, they are furthermore controlled by base metal sulphides (BMS) and micrometric platinum group minerals (PGMs)[3]. This strong control exerted by the host mineralogy and petrology on the S-Se-Te systematics at both the micro-scale and the whole-rock scale makes detailed mineralogical and petrological studies of BMS and PGM a pre-requisite to fully understand and accurately interpret the whole-rock signatures. Here we combine in-situ sulphide data and detailed mineralogical observations with whole-rock S-Se-Te-HSE signatures of both lherzolites and harburgites from different geodynamic settings. We demonstrate that the near-chondritic Se and Te signature of 'fertile' mantle rocks (Se/Te ≈9×5) is not a primitive signature of the Earth's mantle, but rather reflects strong enrichment in metasomatic HSE host phases, which erased previous pristine signatures. Consequently, current attempts to identify a potential Late Veneer composition are seriously flawed because, neither refertilisation/metasomatism nor true melt depletion (e.g. harzburgitic residues) have been taken into account for the Primitive Upper Mantle composition estimate[4]. Our combined whole rock and in-situ sulphide data indicate a refertilisation trend towards sub-chondritic Se/Te ratios (i.e. Se/Te < 2). On the other hand, harzburgites that preserve depletion signatures show suprachondritic Se/Te ratios (< 31). Altogether this shows that metasomatic enrichment of mantle rocks may lead to a systematic bias and hence underestimation of the current Se/Te estimate of the primitive mantle. The metasomatic origin of the reported S, Se and Te ratios in peridotites that reflect the control of metasomatic BMS and PGMs[5;6] furthermore show that not all whole rock signatures in the Earth's mantle that scatter around near-chondritic values are primary and hence challenge the simple conception that these features may readily solve the long-standing conundrum of the Late Veneer composition. Refs: [1] Rose-Weston et al. (2009) GCA 73, 4598-4615; [2] Kimura et al. (1974) GCA 38, 683-701; [3] Lorand and Alard (2010) 67, 4137-4151; [4] Wang and Becker (2013) Nature 499, 328-331; [5] König et al. (2012) GCA 86, 354-366; [6] König et al. (2013, in press), EPSL.

Rare-earth Nanoparticle-induced Cytotoxicity on Spatial Cognition Memory of Mouse Brain.

PubMed

Lin, Cai-Hou; Liu, Gui-Fen; Chen, Jing; Chen, Yan; Lin, Ru-Hui; He, Hong-Xing; Chen, Jian-Ping

2017-11-20

Luminescent rare-earth-based nanoparticles have been increasingly used in nanomedicine due to their excellent physicochemical properties, such as biomedical imaging agents, drug carriers, and biomarkers. However, biological safety of the rare-earth-based nanomedicine is of great significance for future development in practical applications. In particular, biological effects of rare-earth nanoparticles on human's central nervous system are still unclear. This study aimed to investigate the potential toxicity of rare-earth nanoparticles in nervous system function in the case of continuous exposure. Adult ICR mice were randomly divided into seven groups, including control group (receiving 0.9% normal saline) and six experimental groups (10 mice in each group). Luminescent rare-earth-based nanoparticles were synthesized by a reported co-precipitation method. Two different sizes of the nanoparticles were obtained, and then exposed to ICR mice through caudal vein injection at 0.5, 1.0, and 1.5 mg/kg body weight in each day for 7 days. Next, a Morris water maze test was employed to evaluate impaired behaviors of their spatial recognition memory. Finally, histopathological examination was implemented to study how the nanoparticles can affect the brain tissue of the ICR mice. Two different sizes of rare-earth nanoparticles have been successfully obtained, and their physical properties including luminescence spectra and nanoparticle sizes have been characterized. In these experiments, the rare-earth nanoparticles were taken up in the mouse liver using the magnetic resonance imaging characterization. Most importantly, the experimental results of the Morris water maze tests and histopathological analysis clearly showed that rare-earth nanoparticles could induce toxicity on mouse brain and impair the behaviors of spatial recognition memory. Finally, the mechanism of adenosine triphosphate quenching by the rare-earth nanoparticles was provided to illustrate the toxicity on the mouse brain. This study suggested that long-term exposure of high-dose bare rare-earth nanoparticles caused an obvious damage on the spatial recognition memory in the mice.

Concentrations and health risk assessment of rare earth elements in vegetables from mining area in Shandong, China.

PubMed

Zhuang, Maoqiang; Zhao, Jinshan; Li, Suyun; Liu, Danru; Wang, Kebo; Xiao, Peirui; Yu, Lianlong; Jiang, Ying; Song, Jian; Zhou, Jingyang; Wang, Liansen; Chu, Zunhua

2017-02-01

To investigate the concentrations of rare earth elements in vegetables and assess human health risk through vegetable consumption, a total of 301 vegetable samples were collected from mining area and control area in Shandong, China. The contents of 14 rare earth elements were determined by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The total rare earth elements in vegetables from mining and control areas were 94.08 μg kg -1 and 38.67 μg kg -1 , respectively, and the difference was statistically significant (p < 0.05). The leaf vegetable had the highest rare earth elements concentration (984.24 μg kg -1 and 81.24 μg kg -1 for mining and control areas, respectively) and gourd vegetable had the lowest rare earth elements concentration (37.34 μg kg -1 and 24.63 μg kg -1 for mining and control areas, respectively). For both areas, the rare earth elements concentration in vegetables declined in the order of leaf vegetable > taproot vegetable > alliaceous vegetable > gourd vegetable. The rare earth elements distribution patterns for both areas were characterized by enrichment of light rare earth elements. The health risk assessment demonstrated that the estimated daily intakes (0.69 μg kg -1 d -1 and 0.28 μg kg -1 d -1 for mining and control areas, respectively) of rare earth elements through vegetable consumption were significantly lower than the acceptable daily intake (70 μg kg -1 d -1 ). The damage to adults can be neglected, but more attention should be paid to the effects of continuous exposure to low levels of rare earth elements on children. Copyright © 2016 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The RE Light process is a process that recycles fluorescent lamps for their rare earth and mercury. There is a limited U.S. market for recycled rare earth materials and current rare earth prices make domestic production cost-prohibitive.

Alternatives to antibiotics as growth promoters for use in swine production: a review

PubMed Central

2013-01-01

In the past two decades, an intensive amount of research has been focused on the development of alternatives to antibiotics to maintain swine health and performance. The most widely researched alternatives include probiotics, prebiotics, acidifiers, plant extracts and neutraceuticals such as copper and zinc. Since these additives have been more than adequately covered in previous reviews, the focus of this review will be on less traditional alternatives. The potential of antimicrobial peptides, clay minerals, egg yolk antibodies, essential oils, eucalyptus oil-medium chain fatty acids, rare earth elements and recombinant enzymes are discussed. Based on a thorough review of the literature, it is evident that a long and growing list of compounds exist which have been tested for their ability to replace antibiotics as feed additives in diets fed to swine. Unfortunately, the vast majority of these compounds produce inconsistent results and rarely equal antibiotics in their effectiveness. Therefore, it would appear that research is still needed in this area and that the perfect alternative to antibiotics does not yet exist. PMID:24034214

Biogeochemistry of the rare-earth elements with particular reference to hickory trees

USGS Publications Warehouse

Robinson, W.O.; Bastron, H.; Murata, K.J.

1958-01-01

Hickory trees concentrate the rare-earth elements in their leaves to a phenomenal degree and may contain as much as 2300 p.p.m. of total rare earths based on the dry weight of the leaves. The average proportions of the individual elements (atomic percent of the total rare-earth elements) in the leaves are: Y 36, La 16, Ce 14, Pr 2, Nd 20, Sm 1, Eu 0.7, Gd 3, Tb 0.6, Dy 3, Ho 0.7, Er 2, Tm 0.2, Yb 1, and Lu 0.2. The similarity in the proportions of the rare-earth elements in the leaves and in the exchange complex of the soil on which the hickory trees grow indicates that the trees do not fractionate the rare earths appreciably. The variation of the rare-earth elements in the leaves and soils can be explained generally in terms of the relative abundance of the cerium group and the yttrium group, except for the element cerium. The large fluctuations in the proportion of cerium [Ce/(La + Nd) atomic ratios of 0.16 to 0.86] correlate with oxidation-reduction conditions in the soil profile. The substitution of dilute H2SO3 for dilute HC1 in the determination of available rare-earth elements brings about a large increase in the proportion of cerium that is extracted from an oxygenated subsoil. These relationships strongly suggest that quadrivalent cerium is present in oxygenated subsoil and is less available to plants than the other rare-earth elements that do not undergo such a change in valence. A few parts per billion of rare-earth elements have been detected in two samples of ground water. ?? 1958.

Buffer layers for coated conductors

DOEpatents

Stan, Liliana [Los Alamos, NM; Jia, Quanxi [Los Alamos, NM; Foltyn, Stephen R [Los Alamos, NM

2011-08-23

A composite structure is provided including a base substrate, an IBAD oriented material upon the base substrate, and a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material. Additionally, an article is provided including a base substrate, an IBAD oriented material upon the base substrate, a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material, and a thick film upon the cubic metal oxide material. Finally, a superconducting article is provided including a base substrate, an IBAD oriented material upon the base substrate, a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material, and an yttrium barium copper oxide material upon the cubic metal oxide material.

Some metal-graphite and metal-ceramic composites for use as high energy brake lining materials

NASA Technical Reports Server (NTRS)

Bill, R. C.

1974-01-01

Materials were studied as candidates for development as potential new aircraft brake lining materials. These families were (1) copper-graphite composites; (2) nickel-graphite composites; (3) copper - rare-earth-oxide (gadolinium oxide (Gd2O3) or lanthanum oxide (La2O3)) composites and copper - rare-earth-oxide (La2O3) - rare-earth-fluoride (lanthanum fluoride (LaF3)) composites; (4) nickel - rare-earth-oxide composites and nickel - rare-earth-oxide - rare-earth-fluoride composites. For comparison purposes, a currently used metal-ceramic composite was also studied. Results showed that the nickel-Gd2O3 and nickel-La2O3-LaF3 composites were comparable or superior in friction and wear performance to the currently used composite and therefore deserve to be considered for further development.

Transient symptomatic zinc deficiency resembling acrodermatitis enteropathica in a breast-fed premature infant: case report and brief review of the literature.

PubMed

Zattra, E; Belloni Fortina, A

2013-12-01

Transient symptomatic zinc deficiency is a rare disorder clinically indistinguishable from acrodermatitis enteropathica characterized by periorificial and acral dermatitis that usually occurs in exclusively breast-fed infant especially if preterm. We describe a three-month-old breast-fed preterm boy who developed the typical skin lesions. Maternal breast milk zinc was lower than the levels from other 2 mothers of infants at the same gestational age. The disease improved and serum zinc level became normal with oral supplementation of zinc. No recurrence of the dermatosis was observed when the treatment was stopped after weaning.

40 CFR 721.10423 - Complex strontium aluminate, rare earth doped (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... earth doped (generic). 721.10423 Section 721.10423 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10423 Complex strontium aluminate, rare earth doped... substances identified generically as complex strontium aluminate, rare earth doped (PMNs P-12-22, P-12-23, P...

[Physiological effects of rare earth elements and their application in traditional Chinese medicine].

PubMed

Zhou, Jie; Guo, Lanping; Xiao, Wenjuan; Geng, Yanling; Wang, Xiao; Shi, Xin'gang; Dan, Staerk

2012-08-01

The process in the studies on physiological effects of rare earth elements in plants and their action mechanisms were summarized in the aspects of seed germination, photosynthesis, mineral metabolism and stress resistance. And the applications of rare earth elements in traditional Chinese medicine (TCM) in recent years were also overviewed, which will provide reference for further development and application of rare earth elements in TCM.

Critical Rare Earths, National Security, and U.S.-China Interactions: A Portfolio Approach to Dysprosium Policy Design

DTIC Science & Technology

2015-01-01

by the graduate fellow’s faculty committee. C O R P O R A T I O N Dissertation Critical Rare Earths, National Security, and U.S.-China Interactions A...Portfolio Approach to Dysprosium Policy Design David L. An Dissertation Critical Rare Earths, National Security, and U.S.-China Interactions A...Permanent Magnet ................................................ xxiv Dysprosium, the Most Critical Rare Earth

Analysis of “Favorable Growth Element” Based on Rare Earth-aluminum Composite Mechanism of Compound Process

NASA Astrophysics Data System (ADS)

Hao, Baohong; Zeng, Qihui; Zhao, Jin

2018-01-01

Under the background that failure resulted in by high temperature once only aluminum oxide is used as the gasoline additive. This paper, with the purpose to solve this problem, is to synthesize AcAl oxide for gasoline additive. In order to get the rare-earth-aluminum oxide, first, a complex model of rare earth oxide based on theories about ion coordination is established. Then, by the complex model, the type of “compound growth unit” when rare earth elements join the hydrothermal conditions and the inclination that “diversification” might probably happen are deduced. Depending on the results got by complex model, this paper introduces the type of compound and its existence conditions of “Compound growth unit” owned by stable rare-earth-aluminum oxide. By adjusting the compositions of modifier, compound materials of rare earth-aluminum oxide used for gasoline additive is made. By XRD test, aperture test, adsorption test and desorption test, the theoretical deduction is proved to be right. From the experiment, it is concluded that: a dense environment is the pre-condition to form rare-earth-aluminum polymer, which is also an essential condition for the polymer to update to a favorable growth unit and produce mesoporous rare-earth-aluminum oxide with high activity.

Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system.

PubMed

Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

2013-06-15

The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid-liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system. Copyright © 2013 Elsevier B.V. All rights reserved.

The study of metal sulphide nanomaterials obtained by chemical bath deposition and hot-injection technique

NASA Astrophysics Data System (ADS)

Maraeva, E. V.; Alexandrova, O. A.; Forostyanaya, N. A.; Levitskiy, V. S.; Mazing, D. S.; Maskaeva, L. N.; Markov, V. Ph; Moshnikov, V. A.; Shupta, A. A.; Spivak, Yu M.; Tulenin, S. S.

2015-11-01

In this study lead sulphide - cadmium sulphide based layers were obtained through chemical deposition of water solutions and cadmium sulphide quantum dots were formed through hot-injection technique. The article discusses the results of surface investigations with the use of atomic force microscopy, Raman spectroscopy and photoluminescence measurements.

Removal of mercury (II), elemental mercury and arsenic from simulated flue gas by ammonium sulphide.

PubMed

Ning, Ping; Guo, Xiaolong; Wang, Xueqian; Wang, Ping; Ma, Yixing; Lan, Yi

2015-01-01

A tubular resistance furnace was used as a reactor to simulate mercury and arsenic in smelter flue gases by heating mercury and arsenic compounds. The flue gas containing Hg(2+), Hg(0) and As was treated with ammonium sulphide. The experiment was conducted to investigate the effects of varying the concentration of ammonium sulphide, the pH value of ammonium sulphide, the temperature of ammonium sulphide, the presence of SO2 and the presence of sulphite ion on removal efficiency. The prepared adsorption products were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. The results showed that the optimal concentration of ammonium sulphide was 0.8 mol/L. The optimal pH value of ammonium sulphide was 10, and the optimal temperature of ammonium sulphide was 20°C.Under the optimum conditions, the removal efficiency of Hg(2+), Hg(0) and As could reach 99%, 88.8%, 98%, respectively. In addition, SO2 and sulphite ion could reduce the removal efficiency of mercury and arsenic from simulated flue gas.

Improved method for preparing rare earth sesquichalcogenides

DOEpatents

Takeshita, T.; Beaudry, B.J.; Gschneidner, K.A. Jr.

1982-04-14

An improved method for the preparation of high purity rare earth sesquichalcogenides is described. The rare earth, as one or more pieces of the metal, is sealed under a vacuum with a stoichiometric amount of sulfur or selenium and a small amount of iodine into a quartz reaction vessel. The sealed vessel is then heated to above the vaporization temperature of the chalcogen and below the melting temperature of the rare earth metal and maintained until the product has been formed. The iodine is then vaporized off leaving a pure product. The rare earth sulfides and selenides thus formed are useful as semiconductors and as thermoelectric generators. 3 tables.

Superconducting structure

DOEpatents

Kwon, Chuhee; Jia, Quanxi; Foltyn, Stephen R.

2003-04-01

A superconductive structure including a dielectric oxide substrate, a thin buffer layer of a superconducting material thereon; and, a layer of a rare earth-barium-copper oxide superconducting film thereon the thin layer of yttrium-barium-copper oxide, the rare earth selected from the group consisting of samarium, gadolinium, ytterbium, erbium, neodymium, dysprosium, holmium, lutetium, a combination of more than one element from the rare earth group and a combination of one or more elements from the rare earth group with yttrium, the buffer layer of superconducting material characterized as having chemical and structural compatibility with the dielectric oxide substrate and the rare earth-barium-copper oxide superconducting film is provided.

Hydrogels dispersed by doped rare earth fluoride nanocrystals: ionic liquid dispersion and down/up-conversion luminescence.

PubMed

Yan, Zhi-Yuan; Jia, Li-Ping; Yan, Bing

2014-01-01

Two typical kinds of rare earth fluoride nanocrystals codoped with rare earth ions (Eu(3+) and Tm(3+)/Er(3+),Yb(3+)) are synthesized and dispersed in ionic liquid compound (1-chlorohexane-3-methylimidazolium chloride, abbreviated as [C6mim][Cl]). Assisted by agarose, the luminescent hydrogels are prepared homogeneously. The down/up-conversion luminescence of these hydrogels can be realized for the dispersed rare earth fluoride nanocrystals. The results provide a strategy to prepare luminescent (especially up-conversion luminescent) hydrogels with ionic liquid to disperse rare earth fluoride nanocrystals. Copyright © 2013 Elsevier B.V. All rights reserved.

Superconducting Structure

DOEpatents

Kwon, Chuhee; Jia, Quanxi; Foltyn, Stephen R.

2005-09-13

A superconductive structure including a dielectric oxide substrate, a thin buffer layer of a superconducting material thereon; and, a layer of a rare earth-barium-copper oxide superconducting film thereon the thin layer of yttrium-barium-copper oxide, the rare earth selected from the group consisting of samarium, gadolinium, ytterbium, erbium, neodymium, dysprosium, holmium, lutetium, a combination of more than one element from the rare earth group and a combination of one or more elements from the rare earth group with yttrium, the buffer layer of superconducting material characterized as having chemical and structural compatibility with the dielectric oxide substrate and the rare earth-barium-copper oxide superconducting film is provided.

Detoxification of sulphidic African shelf waters by blooming chemolithotrophs

NASA Astrophysics Data System (ADS)

Lavik, Gaute; Stührmann, Torben; Brüchert, Volker; van der Plas, Anja; Mohrholz, Volker; Lam, Phyllis; Mußmann, Marc; Fuchs, Bernhard M.; Amann, Rudolf; Lass, Ulrich; Kuypers, Marcel M. M.

2009-01-01

Coastal waters support ~90 per cent of global fisheries and are therefore an important food reserve for our planet. Eutrophication of these waters, due to human activity, leads to severe oxygen depletion and the episodic occurrence of hydrogen sulphide-toxic to multi-cellular life-with disastrous consequences for coastal ecosytems. Here we show that an area of ~7,000km2 of African shelf, covered by sulphidic water, was detoxified by blooming bacteria that oxidized the biologically harmful sulphide to environmentally harmless colloidal sulphur and sulphate. Combined chemical analyses, stoichiometric modelling, isotopic incubations, comparative 16S ribosomal RNA, functional gene sequence analyses and fluorescence in situ hybridization indicate that the detoxification proceeded by chemolithotrophic oxidation of sulphide with nitrate and was mainly catalysed by two discrete populations of γ- and ɛ-proteobacteria. Chemolithotrophic bacteria, accounting for ~20 per cent of the bacterioplankton in sulphidic waters, created a buffer zone between the toxic sulphidic subsurface waters and the oxic surface waters, where fish and other nekton live. This is the first time that large-scale detoxification of sulphidic waters by chemolithotrophs has been observed in an open-ocean system. The data suggest that sulphide can be completely consumed by bacteria in the subsurface waters and, thus, can be overlooked by remote sensing or monitoring of shallow coastal waters. Consequently, sulphidic bottom waters on continental shelves may be more common than previously believed, and could therefore have an important but as yet neglected effect on benthic communities.

Cerium-based, intermetallic-strengthened aluminum casting alloy: High-volume co-product development

DOE PAGES

Sims, Zachary C.; Weiss, David; McCall, S. K.; ...

2016-05-23

Here, several rare earth elements are considered by-products to rare earth mining efforts. By using one of these by-product elements in a high-volume application such as aluminum casting alloys, the supply of more valuable rare earths can be globally stabilized. Stabilizing the global rare earth market will decrease the long-term criticality of other rare earth elements. The low demand for Ce, the most abundant rare earth, contributes to the instability of rare earth extraction. In this article, we discuss a series of intermetallic-strengthened Al alloys that exhibit the potential for new high-volume use of Ce. The castability, structure, and mechanicalmore » properties of binary, ternary, and quaternary Al-Ce based alloys are discussed. We have determined Al-Ce based alloys to be highly castable across a broad range of compositions. Nanoscale intermetallics dominate the microstructure and are the theorized source of the high ductility. In addition, room-temperature physical properties appear to be competitive with existing aluminum alloys with extended high-temperature stability of the nanostructured intermetallic.« less

An Overview of Rare Earth Science and Technology

NASA Astrophysics Data System (ADS)

Gschneidner, Karl, Jr.

2012-02-01

Currently rare earth science and technology is robust: this includes all the major branches of science -- biochemistry, chemistry, materials and physics. There are, however, currently some anomalies and distortions especially in the technology and applications sector of the rare earth field, which is caused by the dominance of China on the sales of rare earths and rare earth containing products. For the past 5 to 10 years ˜95% of rare earths utilized in commerce came from China. Although Chinese actions have lead to sudden and large price spikes and export embargoes, the rare earths are still available but at a higher cost. The start up of production in 2011 at mines in the USA and Australia will alleviate this situation in about two years. Basic and applied research on the condensed matter physics/materials science has hardly been impacted by these events, but new research opportunities are opening up especially with regard to the USA's military and energy security. Magnets seems to be the hottest topic, but research on battery materials, phosphors and catalysts are also (or should be) strongly considered.

Characterization of solid airborne particles deposited in snow in the vicinity of urban fossil fuel thermal power plant (Western Siberia).

PubMed

Talovskaya, A V; Yazikov, E G; Filimonenko, E A; Lata, J-C; Kim, J; Shakhova, T S

2017-07-20

Recognition and detailed characterization of solid particles emitted from thermal power plants into the environment is highly important due to their potential detrimental effects on human health. Snow cover is used for the identification of anthropogenic emissions in the environment. However, little is known about types, physical and chemical properties of solid airborne particles (SAP) deposited in snow around thermal power plants. The purpose of this study is to quantify and characterize in detail the traceable SAP deposited in snow near fossil fuel thermal power plant in order to identify its emissions into the environment. Applying the scanning electron microscopy-energy dispersive spectroscopy, and X-ray diffraction, mineral and anthropogenic phase groups in SAP deposited in snow near the plant and in fly ash were observed. We identified quartz, albite and mullite as most abundant mineral phases and carbonaceous matter, slag and spherical particles as dominate anthropogenic phases. This is the first study reporting that zircon and anthropogenic sulphide-bearing, metal oxide-bearing, intermetallic compound-bearing and rare-earth element-bearing particles were detected in snow deposits near thermal power plant. The identified mineral and anthropogenic phases can be used as tracers for fossil fuel combustion emissions, especially with regard to their possible effect on human health.

Factors that Influence the Price of Al, Cd, Co, Cu, Fe, Ni, Pb, Rare Earth Elements, and Zn

USGS Publications Warehouse

Papp, John F.; Bray, E. Lee; Edelstein, Daniel L.; Fenton, Michael D.; Guberman, David E.; Hedrick, James B.; Jorgenson, John D.; Kuck, Peter H.; Shedd, Kim B.; Tolcin, Amy C.

2008-01-01

This report is based on a presentation delivered at The 12th International Battery Materials Recycling Seminar, March 17-20, 2008, Fort Lauderdale, Fla., about the factors that influence prices for aluminum, cadmium, cobalt, copper, iron, lead, nickel, rare earth elements, and zinc. These are a diverse group of metals that are of interest to the battery recycling industry. Because the U.S. Geological Survey (USGS) closely monitors, yet neither buys nor sells, metal commodities, it is an unbiased source of metal price information and analysis. The authors used information about these and other metals collected and published by the USGS (U.S. production, trade, stocks, and prices and world production) and internationally (consumption and stocks by country) from industry organizations, because metal markets are influenced by activities and events over the entire globe. Long-term prices in this report, represented by unit values, were adjusted to 1998 constant dollars to remove the effects of inflation. A previous USGS study in this subject area was 'Economic Drivers of Mineral Supply' by Lorie A. Wagner, Daniel E. Sullivan, and John L. Sznopek (USGS Open File Report 02-335). By seeking a common cause for common behavior of prices among the various metal commodities, the authors found that major factors that influence prices of metal commodities were international events such as wars and recessions, and national events such as the dissolution of the Soviet Union in 1991 and economic growth in China, which started its open door policy in the 1970s but did not have significant market impact until the 1990s. Metal commodity prices also responded to commodity-specific events such as tariff or usage changes or mine strikes. It is shown that the prices of aluminum, cadmium, copper, iron, lead, nickel, and zinc are at historic highs, that world stocks are at (or near) historic lows, and that China's consumption of these metals had increased substantially, making it the world's leading consumer of these metals.

Evaluation of Rare Earth Element Extraction from North Dakota Coal-Related Feed Stocks

NASA Astrophysics Data System (ADS)

Laudal, Daniel A.

The rare earth elements consist of the lanthanide series of elements with atomic numbers from 57-71 and also include yttrium and scandium. Due to their unique properties, rare earth elements are crucial materials in an incredible array of consumer goods, energy system components and military defense applications. However, the global production and entire value chain for rare earth elements is dominated by China, with the U.S. currently 100% import reliant for these critical materials. Traditional mineral ores including previously mined deposits in the U.S., however, have several challenges. Chief among these is that the content of the most critical and valuable of the rare earths are deficient, making mining uneconomical. Further, the supply of these most critical rare earths is nearly 100% produced in China from a single resource that is only projected to last another 10 to 20 years. The U.S. currently considers the rare earths market an issue of national security. It is imperative that alternative domestic sources of rare earths be identified and methods developed to produce them. Recently, coal and coal byproducts have been identified as one of these promising alternative resources. This dissertation details a study on evaluation of the technical and economic feasibility of rare earth element recovery from North Dakota lignite coal and lignite-related feedstocks. There were four major goals of this study: i) identify lignite or lignite-related feedstocks with total rare earth element content above 300 parts per million, a threshold dictated by the agency who funded this research as the minimum for economic viability, ii) determine the geochemistry of the feedstocks and understand the forms and modes of occurrence of the rare earth elements, information necessary to inform the development of extraction and concentration methods, iii) identify processing methods to concentrate the rare earth elements from the feedstocks to a target of two weight percent, a value that would be sufficient to leverage existing separation and refining methods developed for the traditional mineral ore industry, and iv) develop a process that is economically viable and environmentally benign. To achieve these overall goals, and to prove or disprove the research hypotheses, the research scope was broken down into three main efforts: i) sampling and characterization of potential feedstocks, ii) laboratory-scale development and testing of rare earth element extraction and concentration methods, and iii) process design and technical and economic feasibility evaluation. In total, 174 unique samples were collected, and several locations were identified that exceeded the 300 ppm total rare earth elements target. The results showed that on a whole sample basis, the rare earths are most concentrated in the clay-rich sediments associated with the coal seams, but on an ash basis in certain locations within certain coal seams the content is significantly higher, an unexpected finding given prior research. At Falkirk Mine near Underwood, North Dakota three coal seams were found to have elevated levels of rare earths, ranging from about 300 to 600 ppm on an ash basis. Additionally, exceptionally high rare earths content was found in samples collected from an outcropping of the Harmon-Hansen coal zone in southwestern North Dakota that contained 2300 ppm on an ash basis. The results dictated that extraction and concentration methods be developed for these rare earth element-rich coals, instead of the mineral-rich sediments. This effort also found that at a commercial-scale, due to non-uniformity of the rare earths content stratigraphically in the coal seams, selective mining practices will be needed to target specific locations within the seams. The bulk mining and blending practices as Falkirk Mine result in a relatively low total rare earths content in the feed coal entering the Coal Creek Power Station adjacent to the mine. Characterization of the coal samples identified that the predominant modes of rare earths occurrence in the lignite coals are associations with the organic matter, primarily as coordination complexes and a lesser amount as ion-exchangeable cations on oxygen functional groups. Overall it appears that about 80-95% of rare earths content in North Dakota lignite is organically associated, and not present in mineral forms, which due to the weak organic bonding, presented a unique opportunity for extraction. The process developed for extraction of rare earths was applied to the raw lignite coals instead of fly ash or other byproducts being investigated extensively in the literature. Rather, the process uses a dilute acid leaching process to strip the organically associated rare earths from the lignite with very high efficiency of about 70-90% at equilibrium contact times. Although the extraction kinetics are quite fast given commercial leaching operations, there is some tradeoff between extraction efficiency and contact time. (Abstract shortened by ProQuest.).

Preface to highly siderophile element constraints on Earth and planetary processes

NASA Astrophysics Data System (ADS)

Riches, Amy J. V.

2017-11-01

The geochemical properties of the highly siderophile elements (HSEs; Os, Ir, Ru, Rh, Pt, Pd, Re and Au) - being strongly iron-loving, but also chalcophile (i.e., having an affinity for sulphide), and generally occurring at ultra trace levels in silicate rocks, their weathered products, and oceanic waters - mean that this suite of elements and their isotopic compositions are useful in tracing a wide variety of processes. Thus, the HSEs are useful probes with which to tackle major research questions pertinent to past and present day change at a variety of scales and in a range of Earth and other-worldly environments by constraining reservoir compositions, chemical drivers, and the timing of key events and/or transformation rates.

Os isotopes in SNC meteorites and their implications to the early evolution of Mars and Earth

NASA Technical Reports Server (NTRS)

Jagoutz, E.; Luck, J. M.; Othman, D. Ben; Wanke, H.

1993-01-01

A new development on the measurement of the Os isotopic composition by mass spectrometry using negative ions opened a new field of applications. The Re-Os systematic provides time information on the differentiation of the nobel metals. The nobel metals are strongly partitioned into metal and sulphide phases, but also the generation of silicate melts might fractionate the Re-Os system. Compared to the other isotopic systems which are mainly dating the fractionation of the alkalis and alkali-earth elements, the Re-Os system is expected to disclose entirely new information about the geochemistry. Especially the differentiation and early evolution of the planets such as the formation of the core will be elucidated with this method.

Effect of composition on SILAR deposited CdxZn1-xS thin films

NASA Astrophysics Data System (ADS)

Ashith V., K.; Gowrish Rao, K.

2018-04-01

In the group of II-VI compound semiconductor, cadmium zinc sulphide (CdxZn1-xS) thin films have broad application in photovoltaic, optoelectronic devices etc. For heterojunction aspects, CdxZn1-xS thin film can be used as heterojunction partner for CdTe as the absorber layer. In this work, CdZnS thin films prepared on glass substrates by Successive Ion Layer Adsorption and Reaction (SILAR) method by varying the composition. The XRD patterns of deposited films showed polycrystalline with the hexagonal phase. The crystallite size of the films was estimated from W-H plot. The bond length of the film varied w.r.to the composition of the CdxZn1-xS films. The urbach energy of the films was calcualted from absorbance data.

Levels of iron, silver, zinc, and lead in oranges and avocados from two gold-rich towns compared with levels in an adjacent gold-deficient town

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golow, A.A.; Laryea, J.N.

1994-09-01

Fruits such as oranges and avocados are important sources of drinks and food in the Ghanaian Society. If such fruits contain various types of metals they may augument the types and amounts of them in the human body. The metals in fruits may depend on what is in the soils from which they are grown. If the soils contain toxic metals like lead, mercury and cadmium then the consumers may be poisoned as happened in the [open quotes]Ouchi - ouchi[close quotes], disease in Japan and similar episodes. In the area under study, the Geological Survey indicates the presence of 2.5more » ppm of lead, 10 - 20 ppm of copper and less than 15 ppm of nickel. Silver, not reported in commercial amounts, is a byproduct of gold productions at Obuasi. Since copper and nickel are presented in the area traces of silver will certainly occur. In the same manner zinc is usually associated with lead as sulphide of zinc blend trace amounts of it are likely to occur in the area. Of the four metals measured, iron and zinc essential for citrus. The extractable iron and zinc in the area of study were 90 and 1.8 mg/kg, levels on the low side for the healthy growth of crops. The investigation reported here is the comparison of the levels of some metals in oranges and avocados from farms in Obuasi and Konongo with those from farms in Kumasi City. This is a part of a project aimed at finding out differences in the metal contents of various food crops grown in various regions of the country. Konongo and Obuasi have soils which are rich in gold but Kumasi city, which is not too distant from these towns, does not have gold in its soil. 18 refs., 1 tab.« less

Rare Earth Element Concentration of Wyoming Thermal Waters Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quillinan, Scott; Nye, Charles; Neupane, Hari

Updated version of data generated from rare earth element investigation of produced waters. These data represent major, minor, trace, isotopes, and rare earth element concentrations in geologic formations and water associated with oil and gas production.

Metal sulfide and rare-earth phosphate nanostructures and methods of making same

DOEpatents

Wong, Stanislaus; Zhang, Fen

2016-06-28

The present invention provides a method of producing a crystalline rare earth phosphate nanostructure. The method comprising: providing a rare earth metal precursor solution and providing a phosphate precursor solution; placing a porous membrane between the metal precursor solution and the phosphate precursor solution, wherein metal cations of the metal precursor solution and phosphate ions of the phosphate precursor solution react, thereby producing a crystalline rare earth metal phosphate nanostructure.

China’s Rare Earth Policies: Economic Statecraft or Interdependence?

DTIC Science & Technology

2012-12-01

statecraft. As evident towards the beginning of the 21st century, China’s policies associated with the rare earths market (e.g., resource quotas...controls approximately 97% of the world’s REE market . These rare earths, which are not widely known because they are so low on the production chain...rare earths as well as access to the developing Chinese market . Additionally, safety and environmental factors will likely raise the cost of

Rare earths, the lanthanides, yttrium and scandium

USGS Publications Warehouse

Bedinger, G.; Bleiwas, D.

2012-01-01

In 2011, rare earths were recovered from bastnasite concentrates at the Mountain Pass Mine in California. Consumption of refined rare-earth products decreased in 2011 from 2010. U.S. rare-earth imports originated primarily from China, with lesser amounts from Austria, Estonia, France and Japan. The United States imported all of its demand for yttrium metal and yttrium compounds, with most of it originating from China. Scandium was imported in various forms and processed domestically.

Condensation and fractionation of rare earths in the solar nebula

NASA Technical Reports Server (NTRS)

Davis, A. M.; Grossman, L.

1979-01-01

The condensation behavior of the rare earth elements in the solar nebula is calculated on the basis of the most recent thermodynamic data in order to construct a model explaining group II rare earth element patterns in Allende inclusions. Models considered all involve the removal of large fractions of the more refractory heavy rare earth elements in an early condensate, followed by the condensation of the remainder at a lower temperature. It is shown that the model of Boynton (1975) in which one rare earth element component is dissolved nonideally in perovskite according to relative activity coefficients can not reasonably be made to fit the observed group II patterns. A model in which two rare earth components control the patterns and dissolve ideally in perovskite is proposed and shown to be able to account for the 20 patterns by variations of the perovskite removal temperature and the relative proportions of the two components.

Self-assemblies of luminescent rare earth compounds in capsules and multilayers.

PubMed

Zhang, Renjie; Shang, Juanjuan; Xin, Jing; Xie, Beibei; Li, Ya; Möhwald, Helmuth

2014-05-01

This review addresses luminescent rare earth compounds assembled in microcapsules as well as in planar films fabricated by the layer-by-layer (LbL) technique, the Langmuir-Blodgett (LB) method and in self-assembled monolayers. Chemical precipitation, electrostatic, van der Waals interactions and covalent bonds are involved in the assembly of these compounds. Self-organized ring patterns of rare earth complexes in Langmuir monolayers and on planar surfaces with stripe patterns, as well as fluorescence enhancement due to donor-acceptor pairs, microcavities, enrichment of rare earth compounds, and shell protection against water are described. Recent information on the tuning of luminescence intensity and multicolors by the excitation wavelength and the ratio of rare earth ions, respectively, are also reviewed. Potential applications of luminescent rare earth complex assemblies serving as biological probes, temperature and gas sensors are pointed out. Copyright © 2014 Elsevier B.V. All rights reserved.

Rare Earth Metals: Resourcefulness and Recovery

NASA Astrophysics Data System (ADS)

Wang, Shijie

2013-10-01

When we appreciate the digital revolution carried over from the twentieth century with mobile communication and the Internet, and when we enjoy our high-tech lifestyle filled with iDevices, hybrid cars, wind turbines, and solar cells in this new century, we should also appreciate that all of these advanced products depend on rare earth metals to function. Although there are only 136,000 tons of annual worldwide demand, (Cho, Rare Earth Metals, Will We Have Enough?)1 rare earth metals are becoming such hot commodities on international markets, due to not only to their increasing uses, including in most critical military hardware, but also to Chinese growth, which accounts for 95% of global rare earth metal production. Hence, the 2013 technical calendar topic, planned by the TMS/Hydrometallurgy and Electrometallurgy Committee, is particularly relevant, with four articles (including this commentary) contributed to the JOM October Issue discussing rare earth metals' resourcefulness and recovery.

Zinc transport and diabetes risk.

PubMed

Pearson, Ewan

2014-04-01

Genome-wide association studies have previously identified variants in SLC30A8, encoding the zinc transporter ZnT8, associated with diabetes risk. A rare variant association study has now established the direction of effect, surprisingly showing that loss-of-function mutations in SLC30A8 are protective against diabetes.

Two main and a new type rare earth elements in Mg alloys: A review

NASA Astrophysics Data System (ADS)

Kong, Linghang

2017-09-01

Magnesium (Mg) alloys stand for the lightest structure engineering materials. Moreover, the strengthening of Mg alloys in ductility, toughness and corrosion predominates their wide applications. With adding rare earth elements in Mg, the mechanical properties will be improved remarkably, especially their plasticity and strength. A brief overview of the addition of rare earth elements for Mg alloys is shown. The basic mechanisms of strengthening Mg alloys with rare earth elements are reviewed, including the solid solution strengthening, grain refinement and long period stacking ordered (LPSO) phase. Furthermore, the available rare earth elements are summarized by type, chemical or physical effects and other unique properties. Finally, some challenge problems that the research is facing and future expectations of ra-re-earth Mg alloys are stated and discussed.

Rare earth metal-containing ionic liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prodius, Denis; Mudring, Anja-Verena

As an innovative tool, ionic liquids (ILs) are widely employed as an alternative, smart, reaction media (vs. traditional solvents) offering interesting technology solutions for dissolving, processing and recycling of metal-containing materials. The costly mining and refining of rare earths (RE), combined with increasing demand for high-tech and energy-related applications around the world, urgently requires effective approaches to improve the efficiency of rare earth separation and recovery. In this context, ionic liquids appear as an attractive technology solution. Finally, this paper addresses the structural and coordination chemistry of ionic liquids comprising rare earth metals with the aim to add to understandingmore » prospects of ionic liquids in the chemistry of rare earths.« less

Rare earth metal-containing ionic liquids

DOE PAGES

Prodius, Denis; Mudring, Anja-Verena

2018-03-07

As an innovative tool, ionic liquids (ILs) are widely employed as an alternative, smart, reaction media (vs. traditional solvents) offering interesting technology solutions for dissolving, processing and recycling of metal-containing materials. The costly mining and refining of rare earths (RE), combined with increasing demand for high-tech and energy-related applications around the world, urgently requires effective approaches to improve the efficiency of rare earth separation and recovery. In this context, ionic liquids appear as an attractive technology solution. Finally, this paper addresses the structural and coordination chemistry of ionic liquids comprising rare earth metals with the aim to add to understandingmore » prospects of ionic liquids in the chemistry of rare earths.« less

Polyurethane Self-Priming Topcoats

DTIC Science & Technology

1992-08-25

QUAIUIY? IPECTED 3 25 aircraft, are exposed to seawater spray in addition to various acid -forming gases such as sulfur dioxide, carbon dioxide, etc...apply particularly since there is a drying time between each application. Further, the removal of a two-coat system can be difficult and time...alkaline earth metal phosphate, e.g., zinc-barium phosphate, (2) zinc salts of benzoic acid or substituted benzoic acid , and (3) molybdate-modified zinc

Aerodynamic Levitation Reactor Studies of Fluorine Reactions with Refractory Ceramics

DTIC Science & Technology

1981-05-01

Melting Points of Rare-Earth Metals and Rare-Earth Trifluorides . 14 3. Aerodynamic Lavitation Flow Reactor. 15 4 Lanthanutm-Boron-Carbon Ternary Phase...the least volatile fluorides (CaF , SrT and rare-earth trifluorides ) would yield a 10% increase in w* (initially O.O cam) in about 1 hour at 1300K...measurement, and are, therefore, somewhat uncertain. The melting points of the rare-earth metals and their trifluorides are illustrated in Fig. 2. The melting

SALICYLATE PROCESS FOR THORIUM SEPARATION FROM RARE EARTHS

DOEpatents

Cowan, G.A.

1959-08-25

The separation of thorium from rare earths is accomplished by forming an aqueous solution of salts of thorium and rare earths and sufficient acetate buffer to provide a pH of between 2 and 5, adding an ammonium salicylate to the aqueous buffered solution, contacting the resultant solution with a substantially water-immiscible organic solvent mixture of an ether and an ester, and separating the solvent extract phase containing thorium salicylate from the aqueous phase containing the rare earths.

Bioleaching of rare earth elements from monazite sand.

PubMed

Brisson, Vanessa L; Zhuang, Wei-Qin; Alvarez-Cohen, Lisa

2016-02-01

Three fungal strains were found to be capable of bioleaching rare earth elements from monazite, a rare earth phosphate mineral, utilizing the monazite as a phosphate source and releasing rare earth cations into solution. These organisms include one known phosphate solubilizing fungus, Aspergillus niger ATCC 1015, as well as two newly isolated fungi: an Aspergillus terreus strain ML3-1 and a Paecilomyces spp. strain WE3-F. Although monazite also contains the radioactive element Thorium, bioleaching by these fungi preferentially solubilized rare earth elements over Thorium, leaving the Thorium in the solid residual. Adjustments in growth media composition improved bioleaching performance measured as rare earth release. Cell-free spent medium generated during growth of A. terreus strain ML3-1 and Paecilomyces spp. strain WE3-F in the presence of monazite leached rare earths to concentrations 1.7-3.8 times those of HCl solutions of comparable pH, indicating that compounds exogenously released by these organisms contribute substantially to leaching. Organic acids released by the organisms included acetic, citric, gluconic, itaconic, oxalic, and succinic acids. Abiotic leaching with laboratory prepared solutions of these acids was not as effective as bioleaching or leaching with cell-free spent medium at releasing rare earths from monazite, indicating that compounds other than the identified organic acids contribute to leaching performance. © 2015 Wiley Periodicals, Inc.

Formation of CaS-MgS in Enstatite Chondrites and Achondrites as a Function of Redox Conditions and Temperature: Constraints on Their Evolution in a Planetesimal and in a Proto-planet

NASA Technical Reports Server (NTRS)

Malavergne, Valerie; Berthet, S.; Righter, K.

2007-01-01

The cubic monosulfide series with the general formula (Mg,Mn,Ca,Fe)S are common phases in the enstatite chondrite (EH) and aubrite meteorite groups. In the Earth s mantle, sulfide minerals are associated with peridotites and eclogites. Study of these sulfide mineral systems is of interest for the mineralogy and petrology of planetary mantles. For example, MgS could occur in the primitive Earth and because it remains a low density phase compared to metal, would stay a separate phase during the core formation process, and thus not segregate to the core. (Mg,Ca,Mn,Fe)S sulphides might thus be important phases even in planetary differentiation processes. The importance of such minerals, and their formation, composition and textural relationships for understanding the genesis of enstatite chondrites and aubrites, has long been recognized. The main objective of this experimental study is to understand the formation and evolution of (Mg,Ca,Mn,Fe)S sulphides, particularly the oldhamite CaS and ningerite MgS, with pressure, temperature but also with redox conditions because EH and aubrites are meteorites that formed under reduced conditions. Piston-cylinder (PC) and multi-anvil (MA) experiments at high pressure (HP) and high temperature (HT) have been performed in order to simulate the evolution of these phases in a small planetary body from a planetesimal (with PC experiments) up to a proto-planet (with MA experiments).

Application of Freeze-Dried Powders of Genetically Engineered Microbial Strains as Adsorbents for Rare Earth Metal Ions.

PubMed

Moriwaki, Hiroshi; Masuda, Reiko; Yamazaki, Yuki; Horiuchi, Kaoru; Miyashita, Mari; Kasahara, Jun; Tanaka, Tatsuhito; Yamamoto, Hiroki

2016-10-12

The adsorption behaviors of the rare earth metal ions onto freeze-dried powders of genetically engineered microbial strains were compared. Cell powders obtained from four kinds of strains, Bacillus subtilis 168 wild type (WT), lipoteichoic acid-defective (ΔLTA), wall teichoic acid-defective (ΔWTA), and cell wall hydrolases-defective (EFKYOJLp) strains, were used as an adsorbent of the rare earth metal ions at pH 3. The adsorption ability of the rare earth metal ions was in the order of EFKYOJLp > WT > ΔLTA > ΔWTA. The order was the same as the order of the phosphorus quantity of the strains. This result indicates that the main adsorption sites for the ions are the phosphate groups and the teichoic acids, LTA and WTA, that contribute to the adsorption of the rare earth metal ions onto the cell walls. The contribution of WTA was clearly greater than that of LTA. Each microbial powder was added to a solution containing 16 kinds of rare earth metal ions, and the removals (%) of each rare earth metal ion were obtained. The scandium ion showed the highest removal (%), while that of the lanthanum ion was the lowest for all the microbial powders. Differences in the distribution coefficients between the kinds of lanthanide ions by the EFKYOJLp and ΔWTA powders were greater than those of the other strains. Therefore, the EFKYOJLp and ΔWTA powders could be applicable for the selective extraction of the lanthanide ions. The ΔLTA powder coagulated by mixing with a rare earth metal ion, although no sedimentation of the WT or ΔWTA powder with a rare earth metal ion was observed under the same conditions. The EFKYOJLp powder was also coagulated, but its flocculating activity was lower than that of ΔLTA. The ΔLTA and EFKYOJLp powders have a long shape compared to those of the WT or ΔWTA strain. The shapes of the cells will play an important role in the sedimentation of the microbial powders with rare earth metal ions. As the results, three kinds of the genetically engineered microbial powders revealed unique adsorption behaviors of the rare earth metal ions.

Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition

PubMed Central

Watling, Helen R.; Shiers, Denis W.; Collinson, David M.

2015-01-01

In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II) and/or reduced inorganic sulphur compounds (RISC), such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As) to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity. PMID:27682094

Effect of oxygen dosing point and mixing on the microaerobic removal of hydrogen sulphide in sludge digesters.

PubMed

Díaz, I; Pérez, S I; Ferrero, E M; Fdz-Polanco, M

2011-02-01

Limited oxygen supply to anaerobic sludge digesters to remove hydrogen sulphide from biogas was studied. Micro-oxygenation showed competitive performance to reduce considerably the additional equipment necessary to perform biogas desulphurization. Two pilot-plant digesters with an HRT of ∼ 20 d were micro-oxygenated at a rate of 0.25 NL per L of feed sludge with a removal efficiency higher than 98%. The way of mixing (sludge or biogas recirculation) and the point of oxygen supply (headspace or liquid phase) played an important role on hydrogen sulphide oxidation. While micro-oxygenation with sludge recirculation removed only hydrogen sulphide from the biogas, dissolved sulphide was removed if micro-oxygenation was performed with biogas recirculation. Dosage in the headspace resulted in a more stable operation. The result of the hydrogen sulphide oxidation was mostly elemental sulphur, partially accumulated in the headspace of the digester, where different sulphide-oxidising bacteria were found. Copyright © 2010 Elsevier Ltd. All rights reserved.

CADMIUM-RARE EARTH BORATE GLASS AS REACTOR CONTROL MATERIAL

DOEpatents

Ploetz, G.L.; Ray, W.E.

1958-11-01

A reactor control rod fabricated from a cadmiumrare earth-borate glass is presented. The rare earth component of this glass is selected from among those rare earths having large neutron capture cross sections, such as samarium, gadolinium or europium. Partlcles of this glass are then dispersed in a metal matrix by standard powder metallurgy techniques.

Half-sandwich rare-earth-catalyzed olefin polymerization, carbometalation, and hydroarylation.

PubMed

Nishiura, Masayoshi; Guo, Fang; Hou, Zhaomin

2015-08-18

The search for new catalysts for more efficient, selective chemical transformations and for the synthesis of new functional materials has been a long-standing research subject in both academia and industry. To develop new generations of catalysts that are superior or complementary to the existing ones, exploring the potential of untapped elements is an important strategy. Rare-earth elements, including scandium, yttrium, and the lanthanides (La-Lu), constitute one important frontier in the periodic table. Rare-earth elements possess unique chemical and physical properties that are different from those of main-group and late-transition metals. The development of rare-earth-based catalysts by taking the advantage of these unique properties is of great interest and importance. The most stable oxidation state of rare-earth metals is 3+, which is difficult to change under many reaction conditions. The oxidative addition and reductive elimination processes often observed in catalytic cycles involving late transition metals are generally difficult in the case of rare-earth complexes. The 18-electron rule that is applicable to late-transition-metal complexes does not fit rare-earth complexes, whose structures are mainly governed by the sterics (rather than the electron numbers) of the ligands. In the lanthanide series (La-Lu), the ionic radius gradually decreases with increasing atomic number because of the influence of the 4f electrons, which show poor shielding of nuclear charge. Rare-earth metal ions generally show strong Lewis acidity and oxophilicity. Rare-earth metal alkyl and hydride species are highly reactive, showing both nucleophilicity and basicity. The combination of these features, such as the strong nucleophilicity and moderate basicity of the alkyl and hydride species and the high stability, strong Lewis acidity, and unsaturated C-C bond affinity of the 3+ metal ions, can make rare-earth metals unique candidates for the formation of excellent single-site catalysts. This Account is intended to give an overview of our recent studies on organo rare-earth catalysis, in particular the synthesis and application of half-sandwich rare-earth alkyl complexes bearing monocyclopentadienyl ligands for olefin polymerization, carbometalation, and hydroarylation. Treatment of half-sandwich rare-earth dialkyl complexes having the general formula CpMR2 with an equimolar amount of an appropriate borate compound such as [Ph3C][B(C6F5)4] can generate the corresponding cationic monoalkyl species, which serve as excellent single-site catalysts for the polymerization and copolymerization of a wide range of olefin monomers such as ethylene, 1-hexene, styrene, conjugated and nonconjugated dienes, and cyclic olefins. The cationic half-sandwich rare-earth alkyl complexes can also catalyze the regio- and stereoselective alkylative alumination of alkenes and alkynes through insertion of the unsaturated C-C bond into the metal-alkyl bond followed by transmetalation between the resulting new alkyl or alkenyl species and an alkylaluminum compound. Moreover, a combination of deprotonative C-H bond activation of appropriate organic compounds such as anisoles and pyridines by the rare-earth alkyl species and insertion of alkenes into the resulting new metal-carbon bond can lead to catalytic C-H bond alkylation of the organic substrates. Most of these transformations are unique to the rare-earth catalysts with selectivity and functional group tolerance different from those of late-transition-metal catalysts.

Determination of thorium and of rare earth elements in cerium earth minerals and ores

USGS Publications Warehouse

Carron, M.K.; Skinner, D.L.; Stevens, R.E.

1955-01-01

The conventional oxalate method for precipitating thorium and the rare earth elements in acid solution exhibits definite solubilities of these elements. The present work was undertaken to establish conditions overcoming these solubilities and to find optimum conditions for precipitating thorium and the rare earth elements as hydroxides and sebacates. The investigations resulted in a reliable procedure applicable to samples in which the cerium group elements predominate. The oxalate precipitations are made from homogeneous solution at pH 2 by adding a prepared solution of anhydrous oxalic acid in methanol instead of the more expensive crystalline methyl oxalate. Calcium is added as a carrier. Quantitative precipitation of thorium and the rare earth elements is ascertained by further small additions of calcium to the supernatant liquid, until the added calcium precipitates as oxalate within 2 minutes. Calcium is removed by precipitating the hydroxides of thorium and rare earths at room temperature by adding ammonium hydroxide to pH > 10. Thorium is separated as the sebacate at pH 2.5, and the rare earths are precipitated with ammonium sebacate at pH 9. Maximum errors for combined weights of thorium and rare earth oxides on synthetic mixtures are ??0.6 mg. Maximum error for separated thoria is ??0.5 mg.

Recovery of rare earths from spent NdFeB magnets of wind turbine: Leaching and kinetic aspects.

PubMed

Kumari, Aarti; Sinha, Manish Kumar; Pramanik, Swati; Sahu, Sushanta Kumar

2018-05-01

Increasing demands of rare earth (RE) metals for advanced technological applications coupled with the scarcity of primary resources have led to the development of processes to treat secondary resources like scraps or end of life products that are often rich in such metals. Spent NdFeB magnet may serve as a potential source of rare earths containing around ∼30% of neodymium and other rare earths. In the present investigation, a pyro-hydrometallurgical process has been developed to recover rare earth elements (Nd, Pr and Dy) from the spent wind turbine magnet. The spent magnet is demagnetized and roasted at 1123 K to convert rare earths and iron to their respective oxides. Roasting of the magnet not only provides selectivity, but enhances the leaching efficiency also. The leaching of the roasted sample with 0.5 M hydrochloric acid at 368 K, 100 g/L pulp density and 500 rpm for 300 min selectively recovers the rare earth elements almost quantitatively leaving iron oxide in the residue. Leaching of rare earth elements with hydrochloric acid follows the mixed controlled kinetic model with activation energy (E a ) of 30.1 kJ/mol in the temperature range 348-368 K. The leaching mechanism is further established by characterizing the leach residues obtained at different time intervals by scanning electron microscopy- energy dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD). Individual rare earth elements from the leach solution containing 16.8 g/L of Nd, 3.8 g/L Pr, 0.28 g/L of Dy and other minor impurity elements could be separated by solvent extraction. However, mixed rare earth oxide of 99% purity was produced by oxalate precipitation followed by roasting. The leach residue comprising of pure hematite has a potential to be used as pigment or can find other applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

[Application of ICP-MS to Detect Rare Earth Elements in Three Economic Macroalgaes in China].

PubMed

Zhao, Yan-fang; Shang, De-rong; Zhai, Yu-xiu; Ning, Jin-song; Ding, Hai-yan; Sheng, Xiao-feng

2015-11-01

In order to investigate the content and distribution of rare earth elements (REE) in main economic macroalgaes in our country, fifteen rare earth elements in three economic macroalgaes (including 30 samples of kelp, 30 samples of laver and 15 samples of Enteromorpha) were detected using ICP-MS method. Results showed that the total content of REE in different species of macroalgaes was different. The highest total content of REE was in Enteromorpha (16,012.0 ng · g⁻¹), while in kelp and laver, the total REE was similar for two macroalgaes (3887.4 and 4318.1 ng · g⁻¹ respectively). The content of fifteen rare earth elements in kelp ranged from 7.9 to 1496.4 ng · g⁻¹; in laver, it ranged from 8.2 to 1836.6 ng · g⁻¹. For Enteromorpha, the concentration of 15 rare earth elements were between 19.2 and 6014.5 ng · g⁻¹. In addition, the content and distribution of different rare earth elements in different macroalgaes was also different. For kelp, the highest content of REE was Ce (1 496.4 ng · g⁻¹), and the second was La (689.1 ng · g⁻¹). For laver, the highest was Y (1836.6 ng · g⁻¹), and the second was Ce (682.2 ng · g⁻¹). For Enteromorpha, the highest was Ce (6014.5 ng · g⁻¹), and the second was La (2902.9 ng · g⁻¹). Present results also showed that three macroalgaes accumulated the light rare earth elements much more than the high rare earth elements. The light rare earth elements occupied 90.9%, 87.3% and 91.1% for kelp, laver and Enteromorpha respectively. The result that the Enteromorpha had high content of rare earth elements could provide important support for opening new research directions for the utilization of Enteromorpha.

Review of rare earth element concentrations in oil shales of the Eocene Green River Formation

USGS Publications Warehouse

Birdwell, Justin E.

2012-01-01

Concentrations of the lanthanide series or rare earth elements and yttrium were determined for lacustrine oil shale samples from the Eocene Green River Formation in the Piceance Basin of Colorado and the Uinta Basin of Utah. Unprocessed oil shale, post-pyrolysis (spent) shale, and leached shale samples were examined to determine if oil-shale processing to generate oil or the remediation of retorted shale affects rare earth element concentrations. Results for unprocessed Green River oil shale samples were compared to data published in the literature on reference materials, such as chondritic meteorites, the North American shale composite, marine oil shale samples from two sites in northern Tibet, and mined rare earth element ores from the United States and China. The Green River oil shales had lower rare earth element concentrations (66.3 to 141.3 micrograms per gram, μg g-1) than are typical of material in the upper crust (approximately 170 μg g-1) and were also lower in rare earth elements relative to the North American shale composite (approximately 165 μg g-1). Adjusting for dilution of rare earth elements by organic matter does not account for the total difference between the oil shales and other crustal rocks. Europium anomalies for Green River oil shales from the Piceance Basin were slightly lower than those reported for the North American shale composite and upper crust. When compared to ores currently mined for rare earth elements, the concentrations in Green River oil shales are several orders of magnitude lower. Retorting Green River oil shales led to a slight enrichment of rare earth elements due to removal of organic matter. When concentrations in spent and leached samples were normalized to an original rock basis, concentrations were comparable to those of the raw shale, indicating that rare earth elements are conserved in processed oil shales.

Sulphide mineral evolution and metal mobility during alteration of the oceanic crust: Insights from ODP Hole 1256D

NASA Astrophysics Data System (ADS)

Patten, C. G. C.; Pitcairn, I. K.; Teagle, D. A. H.; Harris, M.

2016-11-01

Fluxes of metals during the hydrothermal alteration of the oceanic crust have far reaching effects including buffering of the compositions of the ocean and lithosphere, supporting microbial life and the formation of sulphide ore deposits. The mechanisms responsible for metal mobilisation during the evolution of the oceanic crust are complex and are neither fully constrained nor quantified. Investigations into the mineral reactions that release metals, such as sulphide leaching, would generate better understanding of the controls on metal mobility in the oceanic crust. We investigate the sulphide and oxide mineral paragenesis and the extent to which these minerals control the metal budget in samples from Ocean Drilling Program (ODP) Hole 1256D. The ODP Hole 1256D drill core provides a unique sample suite representative of a complete section of a fast-spreading oceanic crust from the volcanic section down to the plutonic complex. The sulphide population at Hole 1256D is divided into five groups based on mineralogical assemblage, lithological location and texture: the magmatic, metasomatised, high temperature hydrothermal, low temperature and patchy sulphides. The initiation of hydrothermal alteration by downward flow of moderate temperature (250-350 °C) hydrothermal fluids under oxidising conditions leads to metasomatism of the magmatic sulphides in the sheeted dyke and plutonic complexes. Subsequent increase in the degree of hydrothermal alteration at temperatures >350 °C under reducing conditions then leads to the leaching of the metasomatised sulphides by rising hydrothermal fluids. Mass balance calculations show that the mobility of Cu, Se and Au occurs through sulphide leaching during high temperature hydrothermal alteration and that the mobility of Zn, As, Sb and Pb is controlled by silicate rather than sulphide alteration. Sulphide leaching is not complete at Hole 1256D and more advanced alteration would mobilise greater masses of metals. Alteration of oxide minerals does not release significant quantities of metal into the hydrothermal fluid at Hole 1256D. Mixing of rising high temperature fluids with low temperature fluids, either in the upper sheeted dyke section or in the transitional zone, triggers local high temperature hydrothermal sulphide precipitation and trapping of Co, Ni, Cu, Zn, As, Ag, Sb, Se, Te, Au, Hg and Pb. In the volcanic section, low temperature fluid circulation (<150 °C) leads to low temperature sulphide precipitation in the form of pyrite fronts that have high As concentrations due to uptake from the circulating fluids. Deep late low temperature circulation in the sheeted dyke and the plutonic complexes results in local precipitation of patchy sulphides and local metal remobilisation. Control of sulphides over Au, Se and Cu throughout fast-spreading mid-oceanic crust history implies that the generation of hydrothermal fluids enriched in these metals, which can eventually form VMS deposits, is strongly controlled by sulphide leaching.

Anthropogenic and natural lead isotopes in Fe-hydroxides and Fe-sulphates in a watershed associated with arsenic-enriched groundwater, Maine, USA

USGS Publications Warehouse

Ayuso, Robert A.; Foley, Nora K.

2008-01-01

A survey of the natural and anthropogenic sources of lead contributing to secondary minerals in sulphidic schists associated with arsenic-enriched groundwater in Coastal Maine shows that the most likely source is natural Pb, particularly from coexisting sulphide minerals. The secondary minerals also reflect notable contributions from anthropogenic Pb. The Pb isotopes establish pathways by which Pb, and by inference As, could have been transported from As-bearing minerals (arsenian pyrite, arsenopyrite, lollingite, orpiment, arsenic oxide and others), via sulphide oxidation or carbonation reactions into multiple generations of secondary minerals (goethite, hematite, jarosite, natrojarosite and others). Lead isotopic compositions of the sulphides and secondary minerals determined by thermal ionization mass spectrometry (n=53) range widely. Lead and As contents of the sulphides and secondary minerals overlap, and are generally positively correlated. Pyrite, the dominant sulphide in sulphidic schists associated with As-enriched groundwater in Coastal Maine, has values of 206Pb/204Pb from 18.186 to 18.391, 207Pb/204Pb from 15.617 to 15.657, 208Pb/204Pb from 38.052 to 38.210, 206Pb/207Pb from c. 1.1625 to 1.1760 and 208Pb/207Pb from c. 2.4276 to 2.4394. Mixtures of Fe-hydroxide and oxide minerals (predominantly goethite and hematite) and secondary Fe-sulphate minerals (jarosite, natrojarosite, rozenite and melanterite) in the sulphidic schists have overlapping but generally higher values of 206Pb/204Pb from 18.495 to 19.747 (one sample at 21.495), 207Pb/204Pb from 15.595 to 15.722 (one sample at 15.839), 208Pb/204Pb from 38.186 to 39.162,206Pb/207Pb from c.1.1860 to 1.2575 (one sample at 1.3855) and 208Pb/207Pb from c. 2.4441 to 2.4865 than the sulphides. Sulphides from Zn-Pb metal mines are somewhat less radiogenic than sulphides from the schists. Other sulphides (mostly pyrite) associated with pegmatites and granitic rocks are heterogeneous and more radiogenic than the pyrite-rich sulphidic schists. Sulphides from other regional bedrock units also have heterogeneous isotope values. Lead isotopic compositions of the sulphides from the sulphidic schists and coexisting Fe-oxides and Fe-sulphates produced by weathering and alteration overlap, but the secondary minerals extend toward more radiogenic values that broadly indicate the addition of Pb from anthropogenic origin. As a component of Pb from extensively used arsenical pesticides may also be present in the secondary minerals, the range in Pb isotope values is consistent with multiple sources: natural Pb from the schists and anthropogenic Pb (industrial and possibly from agricultural activities). Contributions from past mining activities or from other bedrock sources are not implicated.

Perspectives on Permanent Magnetic Materials for Energy Conversion and Power Generation

NASA Astrophysics Data System (ADS)

Lewis, Laura H.; Jiménez-Villacorta, Félix

2013-01-01

Permanent magnet development has historically been driven by the need to supply larger magnetic energy in ever smaller volumes for incorporation in an enormous variety of applications that include consumer products, transportation components, military hardware, and clean energy technologies such as wind turbine generators and hybrid vehicle regenerative motors. Since the 1960s, the so-called rare-earth "supermagnets," composed of iron, cobalt, and rare-earth elements such as Nd, Pr, and Sm, have accounted for the majority of global sales of high-energy-product permanent magnets for advanced applications. In rare-earth magnets, the transition-metal components provide high magnetization, and the rare-earth components contribute a very large magnetocrystalline anisotropy that donates high resistance to demagnetization. However, at the end of 2009, geopolitical influences created a worldwide strategic shortage of rare-earth elements that may be addressed, among other actions, through the development of rare-earth-free magnetic materials harnessing sources of magnetic anisotropy other than that provided by the rare-earth components. Materials engineering at the micron scale, nanoscale, and Angstrom scales, accompanied by improvements in the understanding and characterization of nanoscale magnetic phenomena, is anticipated to result in new types of permanent magnetic materials with superior performance.

Marine aerosol formation from biogenic iodine emissions.

PubMed

O'Dowd, Colin D; Jimenez, Jose L; Bahreini, Roya; Flagan, Richard C; Seinfeld, John H; Hämeri, Kaarle; Pirjola, Liisa; Kulmala, Markku; Jennings, S Gerard; Hoffmann, Thorsten

2002-06-06

The formation of marine aerosols and cloud condensation nuclei--from which marine clouds originate--depends ultimately on the availability of new, nanometre-scale particles in the marine boundary layer. Because marine aerosols and clouds scatter incoming radiation and contribute a cooling effect to the Earth's radiation budget, new particle production is important in climate regulation. It has been suggested that sulphuric acid derived from the oxidation of dimethyl sulphide is responsible for the production of marine aerosols and cloud condensation nuclei. It was accordingly proposed that algae producing dimethyl sulphide play a role in climate regulation, but this has been difficult to prove and, consequently, the processes controlling marine particle formation remains largely undetermined. Here, using smog chamber experiments under coastal atmospheric conditions, we demonstrate that new particles can form from condensable iodine-containing vapours, which are the photolysis products of biogenic iodocarbons emitted from marine algae. Moreover, we illustrate, using aerosol formation models, that concentrations of condensable iodine-containing vapours over the open ocean are sufficient to influence marine particle formation. We suggest therefore that marine iodocarbon emissions have a potentially significant effect on global radiative forcing.

Hydrothermal method of synthesis of rare-earth tantalates and niobates

DOEpatents

Nyman, May D; Rohwer, Lauren E.S.; Martin, James E

2012-10-16

A hydrothermal method of synthesis of a family of rare-earth Group 5 oxides, where the Group 5 oxide is a niobate or tantalate. The rare-earth Group 5 oxides can be doped with suitable emitter ions to form nanophosphors.

Developing a Comprehensive Approach Could Help DOD Better Manage National Security Risks in the Supply Chain

DTIC Science & Technology

2016-02-01

functionality in weapon system components. Many steps in the rare earths supply chain, such as mining , are conducted in China, a situation that may pose...functionality in weapon systems components.1 Many steps in the rare earths supply chain, such as mining and refining the ore, are primarily conducted outside...are difficult and costly to mine and process. Rare earth elements are Page 5 GAO-16-161 Rare Earth Materials often classified as either

P/M Processing of Rare Earth Modified High Strength Steels.

DTIC Science & Technology

1980-12-01

AA094 165 TRW INC CLEVELAND OH MATERIALS TECHNOLOGY F 6 P/N PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS DEC So A A SHEXM(ER NOOŕT76-C...LEVEL’ (7 PIM PROCESSING OF RARE EARTH MODIFIED HIGH STRENGTH STEELS By A. A. SHEINKER 00 TECHNICAL REPORT Prepared for Office of Naval Research...Processing of Rare Earth Modified High 1 Technical -’ 3t eC"Strength Steels * 1dc4,093Se~ 9PEFRIGOGNZTONAEADADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK

Evaluation Of Ion Exchange For Fabrication Of Rare-Earth Doped Waveguides

NASA Astrophysics Data System (ADS)

Howell, Brian P.; Beerling, Timothy

1987-01-01

Rare earth ions are frequently incorporated into lasers by doping common glasses with the ions in the glass melt. This paper describes the potential of using diffusion of the rare earth ion from molten salt baths to incorporate it in the glass. The paper discusses the molten salts, the rare earths as a group, the diffusion phenomena, the glasses, and finally the interaction of all these to produce the process. General predictions of the waveguide profile and potential problems are presented.

The mineral resource potential of the Harrat Nawasif, sheet 21/42 C, Ranyah, sheet 21/42 D, and Jabal Dalfa, sheet 21/43 C quadrangles, Kingdom of Saudi Arabia

USGS Publications Warehouse

Fenton, Michael D.

1983-01-01

Areas with mineral resource potential in the Harrat Nawasif, Ranyah, and Jabal Dalfa quadrangles in the central Precambrian Shield of Saudi Arabia have been identified by reconnaissance rock geochemistry and inspection of ancient prospects. Locally anomalous areas in perthitic, alkalic granite terrane in the Ranyah quadrangle possibly contain niobium, zirconium, thorium, fluorite, rare-earth, tin, molybdenum, or copper mineralization. The reconnaissance rock geochemical survey in layered volcanic and volcaniclastic terrane in the Jabal Dalfa quadrangle identified a zinc anomaly in quartzite and a nickel-copper zone that is an extension of the Jabal Judayr prospect, where a low-grade, nickel-copper sulfide deposit is known. The Precambrian terrane in the Harrat Nawasif quadrangle has no known mineral resource potential.

Enhancement of efficiency by embedding ZnS and Mn-doped ZnS nanoparticles in P3HT:PCBM hybrid solid state solar cells

NASA Astrophysics Data System (ADS)

Jabeen, Uzma; Adhikari, Tham; Shah, Syed Mujtaba; Nunzi, Jean-Michel; Badshah, Amin; Ahmad, Iqbal

2017-06-01

Zinc sulphide (ZnS) and Mn-doped ZnS nanoparticles were synthesized by wet chemical method. The synthesized nanoparticles were characterized by UV-visible, fluorescence, X-ray diffraction (XRD), fourier transform infra-red (FTIR) spectrometer, field emission scanning electron microscope (FESEM) and high resolution transmission electron microscope (HRTEM). Scanning electron microscope (SEM) was used to find particle size while chemical composition of the synthesized materials was investigated by EDAX. UV-visible absorption spectrum of Mn-doped ZnS was slightly shifted to lower wavelength with respect to the un-doped zinc sulphide with decrease in the size of nanoparticles. Consequently, the band gap was tuned from 3.04 to 3.13 eV. The photoluminescence (PL) emission positioned at 597 nm was ascribed to 4T1 → 6A1 transition within the 3d shell of Mn2+. X-ray diffraction (XRD) analysis revealed that the synthesized nanomaterials existed in cubic crystalline state. The effect of embedding un-doped and doped ZnS nanoparticles in the active layer and changing the ratio of PCBM ([6, 6]-phenyl-C61-butyric acid methyl ester) to nanoparticles on the performance of hybrid solar cell was studied. The device with active layer consisting of poly(3-hexylthiophene) (P3HT), [6, 6]-phenyl-C61-butyric acid methyl ester (PCBM), and un-doped ZnS nanoparticles combined in the ratio of (1:0.5:0.5) attained an efficiency of 2.42% which was found 71% higher than the reference device under the same conditions but not containing nanoparticles. Replacing ZnS nanoparticles with Mn-doped ZnS had a little effect on the enhancement of efficiency. The packing behavior and morphology of blend of nanoparticles with P3HT:PCBM were examined using atomic force microscope (AFM) and XRD. Contribution to the topical issue "Materials for Energy harvesting, conversion and storage II (ICOME 2016)", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

Uranium, yttrium, and rare earth elements accumulation during the Cretaceous anoxic events in carbonaceous rocks in the Pacific Ocean

NASA Astrophysics Data System (ADS)

Savelyeva, Olga; Philosofova, Tatyana; Bergal-Kuvikas, Olga; Savelyeva, Svetlana

2017-04-01

We have studied the carbonate-siliceous section of paleooceanic Albian-Cenomanian deposits on the Kamchatsky Mys peninsula (Eastern Kamchatka, Russia) [1].The section is represented by a rhythmic alternation of planktonic limestones and jaspers, accumulated in the open ocean environment. The rhythmicity can be attributed to climate variations that reflect a fluctuation of astronomical parameters (Milankovitch cycles) [2, 3].The section contains two beds enriched in organic carbon, corresponding to the two oceanic anoxic events - MCE and OAE2 [3]. The maximum content of organic matter in those beds reaches 68%. Our geochemical studies revealed an enrichment of the carbonaceous rocks in some major and trace elements including PGE, in comparison with the surrounding limestone and jasper [4].The accumulation of the ore elements in carbonaceous beds is caused by euxinic conditions during sedimentation.The content of uranium, yttrium, and rare earth elements in carbonaceous rocks is up to 60, 142 and 312 ppm respectively. Phosphate grains (bone detritus) with microinclusions of yttrium and uranium minerals were revealed in the carbonaceous rocks using the scanning electron microscope. These data prove the hypothesis of the sorbtion of U and Y by phosphate detritus from seawater. Microprobe analysis also showed an increased content of Cu, Zn, V in some pyrite framboids, which indicates that these elements are fixed in rocks by Fe-sulphide phase or organic matter under euxinic conditions. Our research may bring us closer to understanding the mechanism of syngenetic accumulation of metals in the black shales. This work was supported by the RFBR (No. 16-05-00546). [1] Palechek, T.N., Savelyev, D.P., Savelyeva, O.L. (2010) Stratigraphy and Geological Correlation 18, (1) 63-82. [2] Savelyeva, O.L. (2010). Vestnik Kraunts. Nauki o zemle 1 (15), 45-55 (in Russian). [3] Savelyev, D.P., Savelyeva, O.L., Palechek, T.N., Pokrovsky, B.G. (2012) Geophysical Research Abstracts, 14, EGU2012-1940. [4] Savelyeva, O., Palesskiy, S., Savelyev, D. (2015) Goldschmidt Abstracts, 2015. 2779.

Squeezing clathrate cages to host trivalent rare-earth guests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jian; He, Yuping; Mordvinova, Natalia E.

Strike difference of the trivalent rare-earth cations from their alkali and alkaline-earth peers is in the presence of localized 4f-electrons and strong spin-orbit coupling. Placing trivalent rare-earth cations inside the fullerene molecules or in between the blocks of itinerant magnetic intermetallics gave rise to plethora of fascinating properties and materials. A long-time missing but hardly desired piece is the semiconducting or metallic compound where rare-earth cations are situated inside the oversized polyhedral cages of three-dimensional framework. In this work we present a synthesis of such compounds, rare-earth containing clathrates Ba 8-xR xCu 16P 30. The unambiguous proofs of their compositionmore » and crystal structure were achieved by a combination of synchrotron powder diffraction, time-of-flight neutron powder diffraction, scanning-transmission electron microscopy, and electron energy-loss spectroscopy. Our quantum-mechanical calculations and experimental characterizations show that the incorporation of the rare-earth cations significantly enhances the hole mobility and concentration which results in the drastic increase in the thermoelectric performance.« less

Rare Earth Doped High Temperature Ceramic Selective Emitters

NASA Technical Reports Server (NTRS)

Chubb, Donald L.; Pal, AnnaMarie; Patton, Martin O.; Jenkins, Phillip P.

1999-01-01

As a result of their electron structure, rare earth ions in crystals at high temperature emit radiation in several narrow bands rather than in a continuous blackbody manner. This study develops a spectral emittance model for films of rare earth containing materials. Although there are several possible rare earth doped high temperature materials, this study was confined to rare earth aluminum garnets. Good agreement between experimental and theoretical spectral emittances was found for erbium, thulium and erbium-holmium aluminum garnets. Spectral emittances of these films are sensitive to temperature differences across the film. Emitter efficiency is also a sensitive function of temperature. For thulium aluminum garnet the efficiency is 0.38 at 1700 K but only 0.19 at 1262 K.

Electro-kinetic Separation of Rare Earth Elements Using a Redox-Active Ligand.

PubMed

Fang, Huayi; Cole, Bren E; Qiao, Yusen; Bogart, Justin A; Cheisson, Thibault; Manor, Brian C; Carroll, Patrick J; Schelter, Eric J

2017-10-16

Purification of rare earth elements is challenging due to their chemical similarities. All of the deployed separation methods rely on thermodynamic properties, such as distribution equilibria in solvent extraction. Rare-earth-metal separations based on kinetic differences have not been examined. Herein, we demonstrate a new approach for rare-earth-element separations by exploiting differences in the oxidation rates within a series of rare earth compounds containing the redox-active ligand [{2-(tBuN(O))C 6 H 4 CH 2 } 3 N] 3- . Using this method, a single-step separation factor up to 261 was obtained for the separation of a 50:50 yttrium-lutetium mixture. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rare Earth Element Partition Coefficients from Enstatite/Melt Synthesis Experiments

NASA Technical Reports Server (NTRS)

Schwandt, Craig S.; McKay, Gordon A.

1997-01-01

Enstatite (En(80)Fs(19)Wo(01)) was synthesized from a hypersthene normative basaltic melt doped at the same time with La, Ce, Nd, Sm, Eu, Dy, Er, Yb and Lu. The rare earth element concentrations were measured in both the basaltic glass and the enstatite. Rare earth element concentrations in the glass were determined by electron microprobe analysis with uncertainties less than two percent relative. Rare earth element concentrations in enstatite were determined by secondary ion mass spectrometry with uncertainties less than five percent relative. The resulting rare earth element partition signature for enstatite is similar to previous calculated and composite low-Ca pigeonite signatures, but is better defined and differs in several details. The partition coefficients are consistent with crystal structural constraints.

Deportment of PGE and semimetals in the Volspruit deposit: the most ultramafic PGE horizon of the Bushveld Complex

NASA Astrophysics Data System (ADS)

Tanner, D.; McDonald, I.; Harmer, R. E. J.; Hughes, H. S. R.; Muir, D. D.

2017-12-01

The Volspruit deposit is a zone of disseminated magmatic sulphides carrying Ni-PGE (platinum-group element) mineralization in the Northern Limb of the Bushveld Complex, South Africa. It is one of the few known PGE prospects hosted by the lower ultramafic portion of a layered intrusion and the only known example in the Bushveld Complex. Volspruit therefore provides a unique insight into the processes governing mineralisation early in the Bushveld magmatic system. This study presents a detailed analysis from the northern portion of the Volspruit orebody combining mineralogical and textural observations with sulphide mineral trace element compositions. Electron microscopy reveals a diverse assemblage of Pt-, Pd- and Rh- dominant platinum-group minerals (PGM), electrum, Ag tellurides, Pb-chlorides, Pb-sulphides, U-oxide and monazite. Laser ablation ICP-MS has demonstrated that the Volspruit base metal sulphides have elevated PGE tenors but a range of S/Se values 1414-19319 - greater than other magmatic sulphide deposits in the northern Bushveld. The S/Se values are typical of crustal S and in agreement with previous S isotope data. These data imply a magma with initially high tenor sulphide liquid experienced local contamination from sedimentary S, leading to reduced tenors and elevated S/Se in sulphides coupled with a propensity of Pb- and Zn-bearing minerals (e.g., Pb-sulphide, Pb-chloride and sphalerite) in association with archetypal orthomagmatic sulphide assemblages. Our data demonstrate that assimilation of sedimentary rocks can modify sulphide melt evolution through the addition of metals such as Pb and Zn, not just contamination by sulphur. The Volspruit deposit illustrates the complexity of multi-stage processes governing mineralisation in the ultramafic portions of layered mafic intrusions.

40 CFR 421.271 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals.... (b) The term rare earth metals refers to the elements scandium, yttrium, and lanthanum to lutetium, inclusive. (c) The term mischmetal refers to a rare earth metal alloy comprised of the natural mixture of...

40 CFR 421.275 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... standards for existing sources. The mass of wastewater pollutants in primary rare earth metals process.... PSES for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.271 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals.... (b) The term rare earth metals refers to the elements scandium, yttrium, and lanthanum to lutetium, inclusive. (c) The term mischmetal refers to a rare earth metal alloy comprised of the natural mixture of...

40 CFR 421.271 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals.... (b) The term rare earth metals refers to the elements scandium, yttrium, and lanthanum to lutetium, inclusive. (c) The term mischmetal refers to a rare earth metal alloy comprised of the natural mixture of...

40 CFR 421.275 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... standards for existing sources. The mass of wastewater pollutants in primary rare earth metals process.... PSES for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.271 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals.... (b) The term rare earth metals refers to the elements scandium, yttrium, and lanthanum to lutetium, inclusive. (c) The term mischmetal refers to a rare earth metal alloy comprised of the natural mixture of...

40 CFR 421.275 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... standards for existing sources. The mass of wastewater pollutants in primary rare earth metals process.... PSES for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.275 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... standards for existing sources. The mass of wastewater pollutants in primary rare earth metals process.... PSES for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.275 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... standards for existing sources. The mass of wastewater pollutants in primary rare earth metals process.... PSES for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for any 1...

Method for determination of small amounts of rare earths and thorium in phosphate rocks

USGS Publications Warehouse

Waring, C.L.; Mela, H.

1953-01-01

In laboratory investigations, interest developed in the possible rare-earth content of phosphate samples from Florida and the northwestern United States. Because of the difficulty of making chemical determinations of traces of individual rare earths, a combined chemical-spectrographic method was investigated. After removal of iron by the extraction of the chloride with ether, the rare earths and thorium are concentrated by double oxalate precipitation, using calcium as a carrier. The rare earths are freed from calcium by an ammonium hydroxide precipitation with a fixed amount of aluminum as a carrier. The aluminum also serves as an internal standard in the final spectrographic analysis. The method will determine from 0.02 to 2 mg. of each rare earth with an error no greater than 10%. The investigation has resulted in a fairly rapid and precise procedure, involving no special spectrographic setup. The method could be applied to other types of geologic materials with the same expected accuracy.

Rare-earth-free high energy product manganese-based magnetic materials.

PubMed

Patel, Ketan; Zhang, Jingming; Ren, Shenqiang

2018-06-14

The constant drive to replace rare-earth metal magnets has initiated great interest in an alternative. Manganese (Mn) has emerged to be a potential candidate as a key element in rare-earth-free magnets. Its five unpaired valence electrons give it a large magnetocrystalline energy and the ability to form several intermetallic compounds. These factors have led Mn-based magnets to be a potential replacement for rare-earth permanent magnets for several applications, such as efficient power electronics, energy generators, magnetic recording and tunneling applications, and spintronics. For past few decades, Mn-based magnets have been explored in many different forms, such as bulk magnets, thin films, and nanoparticles. Here, we review the recent progress in the synthesis and structure-magnetic property relationships of Mn-based rare-earth-free magnets (MnBi, MnAl and MnGa). Furthermore, we discuss their potential to replace rare-earth magnetic materials through the control of their structure and composition to achieve the theoretically predicted magnetic properties.

Does sulphate enrichment promote the expansion of Typha domingensis (cattail) in the Florida Everglades?

USGS Publications Warehouse

Li, S.; Mendelssohn, I.A.; Hao, Chen; Orem, W.H.

2009-01-01

1. The expansion of Typha domingensis into areas once dominated by Cladium jamaicense in the Florida Everglades has been attributed to altered hydrology and phosphorus enrichment, although increased concentrations of sulphate and phosphorus often coincide. The potential importance of hydrogen sulphide produced from sulphate in the expansion of Typha has received little attention. The present study aimed to quantify the comparative growth and photosynthetic responses of Cladium and Typha to sulphate/sulphide. 2. Laboratory experiments showed that Cladium is less tolerant of sulphide than Typha. Cladium was adversely affected at sulphide concentrations of approximately 0.22 mm, while Typha continued to grow well and appeared healthy up to 0.69 mm sulphide. 3. Experiments in field mesocosms provided strong support for species-specific differences in physiology and growth. Regardless of interstitial sulphide concentrations attained, Typha grew faster and had a higher photosynthetic capacity than Cladium. However, sulphide concentrations in the mesocosms reached only 0.18 mm which, based on the hydroponic study, was insufficient to affect the growth or photosynthetic responses of either species. Nevertheless, the upper range of sulphide (0.25-0.375 mm) in Everglades' soil is high enough, based on our results, to impact Cladium but not Typha. 4. This research supports the hypothesis that sulphide accumulation could affect plant species differentially and modify species composition. Consequently, the role of sulphate loading should be considered, in conjunction with hydroperiod, phosphorus availability and disturbances, in developing future management plans for the Everglades. ?? 2009 Blackwell Publishing Ltd.

Reverse engineering nuclear properties from rare earth abundances in the r process

NASA Astrophysics Data System (ADS)

Mumpower, M. R.; McLaughlin, G. C.; Surman, R.; Steiner, A. W.

2017-03-01

The bulk of the rare earth elements are believed to be synthesized in the rapid neutron capture process or r process of nucleosynthesis. The solar r-process residuals show a small peak in the rare earths around A∼ 160, which is proposed to be formed dynamically during the end phase of the r process by a pileup of material. This abundance feature is of particular importance as it is sensitive to both the nuclear physics inputs and the astrophysical conditions of the main r process. We explore the formation of the rare earth peak from the perspective of an inverse problem, using Monte Carlo studies of nuclear masses to investigate the unknown nuclear properties required to best match rare earth abundance sector of the solar isotopic residuals. When nuclear masses are changed, we recalculate the relevant β-decay properties and neutron capture rates in the rare earth region. The feedback provided by this observational constraint allows for the reverse engineering of nuclear properties far from stability where no experimental information exists. We investigate a range of astrophysical conditions with this method and show how these lead to different predictions in the nuclear properties influential to the formation of the rare earth peak. We conclude that targeted experimental campaigns in this region will help to resolve the type of conditions responsible for the production of the rare earth nuclei, and will provide new insights into the longstanding problem of the astrophysical site(s) of the r process.

Selective liquid chromatographic separation of yttrium from heavier rare earth elements using acetic acid as a novel eluent.

PubMed

Kifle, Dejene; Wibetoe, Grethe

2013-09-13

One of the major difficulties in the rare earth elements separation is purification of yttrium from heavy rare earth elements. Thus, an HPLC method using acetic acid as novel eluent was explored for selective separation of yttrium form the heavy rare earth elements. When acetic acid is used as a mobile phase yttrium eluted with the lighter lanthanides. This is contrary to its relative position amongst heavier lanthanides when eluents commonly used for separation of rare earth elements were employed. The shift in elution position of yttrium with acetic acid as eluent may reflect a relatively lower stability constant of the yttrium-AcOH complex (in the same order as for the lighter lanthanides) compared to the corresponding AcOH complexes with heavy lanthanides, enabling selective separation of yttrium from the latter. The method was successfully used for selective separation of yttrium in mixed rare earth sample containing about 80% of yttrium and about 20% of heavy rare earth oxides. Thus, the use of AcOH as eluent is an effective approach for separating and determining the trace amounts of heavy rare earth elements in large amounts of yttrium matrix. Separation was performed on C18 column by running appropriate elution programs. The effluent from the column was monitored with diode array detector at absorbance wavelength of 658nm after post column derivatization with Arsenazo III. Copyright © 2013 Elsevier B.V. All rights reserved.

Fractionation of rare-earth elements in allanite and monazite as related to geology of the Mt. Wheeler mine area, Nevada

USGS Publications Warehouse

Lee, D.E.; Bastron, H.

1967-01-01

Rare-earth contents of 20 allanites and 13 monazites, accessory minerals from a restricted outcrop area of intrusive granitic rocks, are reported. A quantity called sigma (??), which is the sum of the atomic percentages of La, Ce and Pr, is used as an index of composition with respect to the rare-earth elements. Values of sigma vary from 61.3 to 80.9 at.% for these allanites and monazites, representing an appreciable range of composition in terms of the rare-earth elements. Degree of fractionation of rare earths varies directly with CaO content of the granitic rocks, which in turn depends largely on proximity of limestone. Four xenoliths included in the study suggest that spotty mosaic equilibria are superimposed on the regional gradients and that locally the degree of fractionation of rare earths responds to whole rock composition over distances of a few yards or less. The chemistry of the granitic rocks under study appears to be similar in some respects to that of alkalio rocks and carbonatites. Allanites from the most calcium-rich rocks show a pronounced concentration of the most basic rare earths, and whole-rock concentrations of such rare constituents as total cerium earths, Zr, F, Ti, Ba and Sr increase sympathetically with whole-rock calcium. The explanation for the concentration gradients observed in this chemical system must involve assimilation more than magmatic differentiation. ?? 1967.

Rare Earth Elements in National Defense: Background, Oversight Issues, and Options for Congress

DTIC Science & Technology

2011-03-31

12 U.S. Department of Energy Report on Critical Mineral Strategy...17 Institute a New Critical Minerals Program...exports of rare earth minerals by 72%. In September 2010, China temporarily cut rare earth exports to Japan apparently over a maritime dispute. This

40 CFR 421.276 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... wastewater pollutants in primary rare earth metals process wastewater introduced into a POTW shall not exceed the following values: (a) Dryer vent water quench and scrubber. PSNS for the Primary Rare Earth Metals...

40 CFR 421.276 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... wastewater pollutants in primary rare earth metals process wastewater introduced into a POTW shall not exceed the following values: (a) Dryer vent water quench and scrubber. PSNS for the Primary Rare Earth Metals...

40 CFR 421.276 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... wastewater pollutants in primary rare earth metals process wastewater introduced into a POTW shall not exceed the following values: (a) Dryer vent water quench and scrubber. PSNS for the Primary Rare Earth Metals...

40 CFR 421.276 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... wastewater pollutants in primary rare earth metals process wastewater introduced into a POTW shall not exceed the following values: (a) Dryer vent water quench and scrubber. PSNS for the Primary Rare Earth Metals...

40 CFR 421.276 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... wastewater pollutants in primary rare earth metals process wastewater introduced into a POTW shall not exceed the following values: (a) Dryer vent water quench and scrubber. PSNS for the Primary Rare Earth Metals...

How PNNL Extracts Rare Earth Elements from Geothermal Brine

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-07-12

By looking at a problem at a nanoscale level, PNNL researchers are developing an economic way to extract valuable rare earth elements from geothermal fluids. This novel approach may help meet the high demand for rare earth elements that are used in many clean energy technologies.

[Distribution characteristic and current situation of soil rare earth contamination in the Bayan Obo mining area and Baotou tailing reservoir in Inner Mongolia].

PubMed

Guo, Wei; Fu, Rui-ying; Zhao, Ren-xin; Zhao, Wen-jing; Guo, Jiang-yuan; Zhang, Jun

2013-05-01

The pollution status and distribution characteristic of rare earth elements in soil were analyzed around Bayan Obo mining area and Baotou tailing reservoir located in Inner Mongolia grassland ecosystem, aiming at grasping the overall situation of grassland ecosystem pollution caused by rare earth elements and providing basic information as well as theoretical basis. The results indicated that seven rare earth elements in soils from different directions of Baotou tailing reservoir accumulated to a certain extent compared to the soil background value of Inner Mongolia. The pollution degree was Ce > La > Nd > Pr > Sm > Y > Eu. Within 50 m from the edge of tailing reservoir, soil rare earth contamination was the most serious, with the concentrations of La, Ce, Pr, Nd, Sm, Eu and Y reaching 11,45.0 mg x kg(-1), 23,636.0 mg x kg(-1), 4568.16 mg x kg(-1) , 6855.51 mg x kg(-1), 582.18 mg x kg(-1), 94.21 mg x kg(-1)), and 136.25 mg x kg(-1), respectively. Owing to the dominant wind direction of northwest, soils from the southeast were contaminated most seriously. For Bayan Obo mining area, the concentrations of seven rare earth elements in soil from the mining area were significantly higher than those of other areas investigated, with the concentrations of La, Ce, Pr, Nd, Sm, Eu and Y reaching 3112.56 mg x kg(-1), 7142.12 mg x kg(-1), 1467.12 mg x kg(-1), 2552.80 mg x kg(-1), 210.80 mg x kg(-1), 36.20 mg x kg(-1) and 63.22 mg x kg(-1), respectively. The soils of six areas of Bayan Obo mining area were all contaminated by rare earth elements, and the contamination degree was in the order of mining area > outside the dump > east side of the railway > the dump > outside the urban area > west side of the railway. Besides, the transportation of rare earth ore led to the soil rare earth contamination along the railway, and the distribution characteristic of rare earth elements in soils along the railway was affected by the dominant wind direction of northwest. Baotou tailing reservoir and Bayan Obo mining area had the same contamination characteristic, and the concentrations of rare earth elements were in accordance with those in the tailings. The health and stabilization of local grassland ecosystem are being threatened by excessive soil rare earth elements.

Rare earths and other trace elements in Luna 16 soil.

NASA Technical Reports Server (NTRS)

Helmke, P. A.; Haskin, L. A.

1972-01-01

An analysis has been made of four small samples of material brought to earth by the Luna 16 mission, with the aim to determine rare earths and other trace elements in these samples. The analytical results are tabulated, and the rare earth abundances are compared with the average for chondrites. A comparison is also made with the results of similar analyses of Apollo samples.

Ternary rare earth-lanthanide sulfides

DOEpatents

Takeshita, Takuo; Gschneidner JR., Karl A.; Beaudry, Bernard J.

1987-01-06

A new ternary rare earth sulfur compound having the formula: where M is a rare earth element selected from the group europium, samarium and ytterbium and x=0.15 to 0.8. The compound has good high-temperature thermoelectric properties and exhibits long-term structural stability up to 1000.degree. C.

40 CFR 421.274 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... Scrubber. NSPS for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for... wet rare earth chlorides Hexachlorobenzene 0.042 0.042 Chromium (total) 1.544 0.626 Lead 1.168 0.542...

40 CFR 421.274 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... Scrubber. NSPS for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for... wet rare earth chlorides Hexachlorobenzene 0.042 0.042 Chromium (total) 1.544 0.626 Lead 1.168 0.542...

40 CFR 421.274 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... Scrubber. NSPS for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for... wet rare earth chlorides Hexachlorobenzene 0.042 0.042 Chromium (total) 1.544 0.626 Lead 1.168 0.542...

Tunable, rare earth-doped solid state lasers

DOEpatents

Emmett, John L.; Jacobs, Ralph R.; Krupke, William F.; Weber, Marvin J.

1980-01-01

Laser apparatus comprising combinations of an excimer pump laser and a rare earth-doped solid matrix, utilizing the 5d-4f radiative transition in a rare earth ion to produce visible and ultra-violet laser radiation with high overall efficiency in selected cases and relatively long radiative lifetimes.

40 CFR 421.274 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... Scrubber. NSPS for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for... wet rare earth chlorides Hexachlorobenzene 0.042 0.042 Chromium (total) 1.544 0.626 Lead 1.168 0.542...

40 CFR 421.274 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth... Scrubber. NSPS for the Primary Rare Earth Metals Subcategory Pollutant or pollutant property Maximum for... wet rare earth chlorides Hexachlorobenzene 0.042 0.042 Chromium (total) 1.544 0.626 Lead 1.168 0.542...

METHOD OF SEPARATING RARE EARTHS BY ION EXCHANGE

DOEpatents

Spedding, F.H.; Powell, J.E.

1960-10-18

A process is given for separating yttrium and rare earth values having atomic numbers of from 57 through 60 and 68 through 71 from an aqueous solution whose pH value can range from 1 to 9. All rare earths and yttrium are first adsorbed on a cation exchange resin, and they are then eluted with a solution of N-hydroxyethylethylenediaminetriacetic acid (HEDTA) in the order of decreasing atomic number, yttrium behaving like element 61; the effluents are collected in fractions. The HEDTA is recovered by elution with ammonia solution and the resin is regenerated with sulfuric acid. Rare earths are precipitated from the various effluents with oxalic acid, and each supernatant is passed over cation exchange resin for adsorption of HEDTA and nonprecipitated rare earths: the oxalic acid is not retained by the resin.

The Effect of Rare Earth on the Structure and Performance of Laser Clad Coatings

NASA Astrophysics Data System (ADS)

Bao, Ruiliang; Yu, Huijun; Chen, Chuanzhong; Dong, Qing

Laser cladding is one kind of advanced surface modification technology and has the abroad prospect in making the wear-resistant coating on metal substrates. However, the application of laser cladding technology does not achieve the people's expectation in the practical production because of many defects such as cracks, pores and so on. The addiction of rare earth can effectively reduce the number of cracks in the clad coating and enhance the coating wear-resistance. In the paper, the effects of rare earth on metallurgical quality, microstructure, phase structure and wear-resistance are analyzed in turns. The preliminary discussion is also carried out on the effect mechanism of rare earth. At last, the development tendency of rare earth in the laser cladding has been briefly elaborated.

A reactive distillation process for the treatment of LiCl-KCl eutectic waste salt containing rare earth chlorides

NASA Astrophysics Data System (ADS)

Eun, H. C.; Choi, J. H.; Kim, N. Y.; Lee, T. K.; Han, S. Y.; Lee, K. R.; Park, H. S.; Ahn, D. H.

2016-11-01

The pyrochemical process, which recovers useful resources (U/TRU metals) from used nuclear fuel using an electrochemical method, generates LiCl-KCl eutectic waste salt containing radioactive rare earth chlorides (RECl3). It is necessary to develop a simple process for the treatment of LiCl-KCl eutectic waste salt in a hot-cell facility. For this reason, a reactive distillation process using a chemical agent was achieved as a method to separate rare earths from the LiCl-KCl waste salt. Before conducting the reactive distillation, thermodynamic equilibrium behaviors of the reactions between rare earth (Nd, La, Ce, Pr) chlorides and the chemical agent (K2CO3) were predicted using software. The addition of the chemical agent was determined to separate the rare earth chlorides into an oxide form using these equilibrium results. In the reactive distillation test, the rare earth chlorides in LiCl-KCl eutectic salt were decontaminated at a decontamination factor (DF) of more than 5000, and were mainly converted into oxide (Nd2O3, CeO2, La2O3, Pr2O3) or oxychloride (LaOCl, PrOCl) forms. The LiCl-KCl was purified into a form with a very low concentration (<1 ppm) for the rare earth chlorides.

Ferroelectricity of domain walls in rare earth iron garnet films.

PubMed

Popov, A I; Zvezdin, K A; Gareeva, Z V; Mazhitova, F A; Vakhitov, R M; Yumaguzin, A R; Zvezdin, A K

2016-11-16

In this paper, we report on electric polarization arising in a vicinity of Bloch-like domain walls in rare-earth iron garnet films. The domain walls generate an intrinsic magnetic field that breaks an antiferroelectric structure formed in the garnets due to an exchange interaction between rare earth and iron sublattices. We explore 180° domain walls whose formation is energetically preferable in the films with perpendicular magnetic anisotropy. Magnetic and electric structures of the 180° quasi-Bloch domain walls have been simulated at various relations between system parameters. Singlet, doublet ground states of rare earth ions and strongly anisotropic rare earth Ising ions have been considered. Our results show that electric polarization appears in rare earth garnet films at Bloch domain walls, and the maximum of magnetic inhomogeneity is not always linked to the maximum of electric polarization. A number of factors including the temperature, the state of the rare earth ion and the type of a wall influence magnetically induced electric polarization. We show that the value of polarization can be enhanced by the shrinking of the Bloch domain wall width, decreasing the temperature, and increasing the deviations of magnetization from the Bloch rotation that are regulated by impacts given by magnetic anisotropies of the films.

[Effects of arbuscular mycorrhizal fungi on the growth and rare earth elements uptake of soybean grown in rare earth mine tailings].

PubMed

Guo, Wei; Zhao, Ren-xin; Zhao, Wen-jing; Fu, Rui-ying; Guo, Jiang-yuan; Zhang, Jun

2013-05-01

A greenhouse pot experiment was conducted to investigate the influence of arbuscular mycorrhizal (AM) fungi Glomus versiforme on the plant growth, nutrient uptake, C: N: P stoichiometric, uptake of heavy metals and rare earth elements by soybean (Glycine max) grown in rare earth mine tailings. The aim was to provide a basis for the revegetation of rare earth mine tailings. The results indicated that soybean had a high mycorrhizal colonization and symbiotic associations were successfully established with G. versiforme, with an average rate of approximately 67%. The colonization of G. versiforme significantly promoted the growth of soybean, increased P, K contents, and decreased C: N: P ratios, supporting the growth rate hypothesis. Inoculation with G. versiforme significantly decreased shoots and roots La, Ce, Pr and Nd concentrations of soybean compared to the control treatment. However, inoculation with G. versiforme had no significant effect on the heavy metal concentrations, except for significantly decreased shoot Fe and Cr concentrations and increased root Cd concentrations. The experiment demonstrates that AM fungi have a potential role for soybean to adapt the composite adversity of rare earth tailings and play a positive role in revegetation of rare earth mine tailings. Further studies on the role of AM fungi under natural conditions should be conducted.

Optimization Of Optoelectronic Characteristics Of Sintered Cadmium Sulphide Photoconductive Layers

NASA Astrophysics Data System (ADS)

Chockalingam, Mary J.; Suryanarayana, C. V.

1986-11-01

Photograde cadmium sulphide useful for sintered polycrystalline cadmium sulphide photoconductive cells as also for solar cells can be prepared by a simple chemical reaction between a soluble cadmium salt and thiourea in an aqueous alkaline solution by optimising the pH, temperature and concentration of the constituents in the bath. The precipitated cadmium-sulphide after drying at 120°C was found to result in a photograde quality of 99.999% pure cadmium sulphide as estimated by atomic absorption spectrophotometer. Details are given in this paper, of the process of preparation of CdS powder, screen printing and sintering the cadmium sulphide layers to give finally the photoconductive cell which gave on irradiation a change in the resistance of six to seven orders. The sintering technique and the mechanism of the reaction resulting in high photosensitivity of the layer obtained are discussed in detail.

The effects of composition and temperature on chalcophile and lithophile element partitioning into magmatic sulphides

NASA Astrophysics Data System (ADS)

Kiseeva, Ekaterina S.; Wood, Bernard J.

2015-08-01

We develop a comprehensive model to describe trace and minor element partitioning between sulphide liquids and anhydrous silicate liquids of approximately basaltic composition. We are able thereby to account completely for the effects of temperature and sulphide composition on the partitioning of Ag, Cd, Co, Cr, Cu, Ga, Ge, In, Mn, Ni, Pb, Sb, Ti, Tl, V and Zn. The model was developed from partitioning experiments performed in a piston-cylinder apparatus at 1.5 GPa and 1300 to 1700 °C with sulphide compositions covering the quaternary FeSsbnd NiSsbnd CuS0.5sbnd FeO. Partitioning of most elements is a strong function of the oxygen (or FeO) content of the sulphide. This increases linearly with the FeO content of the silicate melt and decreases with Ni content of the sulphide. As expected, lithophile elements partition more strongly into sulphide as its oxygen content increases, while chalcophile elements enter sulphide less readily with increasing oxygen. We parameterised the effects by using the ε-model of non-ideal interactions in metallic liquids. The resulting equation for partition coefficient of an element M between sulphide and silicate liquids can be expressed as We used our model to calculate the amount of sulphide liquid precipitated along the liquid line of descent of MORB melts and find that 70% of silicate crystallisation is accompanied by ∼0.23% of sulphide precipitation. The latter is sufficient to control the melt concentrations of chalcophile elements such as Cu, Ag and Pb. Our partition coefficients and observed chalcophile element concentrations in MORB glasses were used to estimate sulphur solubility in MORB liquids. We obtained between ∼800 ppm (for primitive MORB) and ∼2000 ppm (for evolved MORB), values in reasonable agreement with experimentally-derived models. The experimental data also enable us to reconsider Ce/Pb and Nd/Pb ratios in MORB. We find that constant Ce/Pb and Nd/Pb ratios of 25 and 20, respectively, can be achieved during fractional crystallisation of magmas generated by 10% melting of depleted mantle provided the latter contains >100 ppm S and about 650 ppm Ce, 550 ppm Nd and 27.5 ppb Pb. Finally, we investigated the hypothesis that the pattern of chalcophile element abundances in the mantle was established by segregation of a late sulphide matte. Taking the elements Cu, Ag, Pb and Zn as examples we find that the Pb/Zn and Cu/Ag ratios of the mantle can, in principle, be explained by segregation of ∼0.4% sulphide matte to the core.

Flotation as a remediation technique for heavily polluted dredged material. 1. A feasibility study.

PubMed

Cauwenberg, P; Verdonckt, F; Maes, A

1998-01-19

The flotation behaviour of highly polluted dredged material was investigated at different pH values by mechanical agitated (Denver) flotation. Up to 80% of cadmium, copper, lead and zinc could be concentrated in the froth layer which represented only 30% of the total mass. The maximum specificity for heavy metals, defined as the concentrating factor, was obtained at pH 8-9. The maximum recovery of heavy metals on the other hand was found to be reached at elevated pH values (pH 12). In addition the specificity of the flotation process for the transition metals could be assigned to their presence as metal sulphides in the dredged material. However, the interaction with organic matter is an important factor in determining their flotability. The carbonate fraction was irrelevant for the flotation behaviour of heavy metals.

Nanostructure CdS/ZnO heterojunction configuration for photocatalytic degradation of Methylene blue

NASA Astrophysics Data System (ADS)

Velanganni, S.; Pravinraj, S.; Immanuel, P.; Thiruneelakandan, R.

2018-04-01

In the present manuscript, thin films of Zinc Oxide (ZnO) have been deposited on a FTO substrate using a simple successive ionic layer adsorption and reaction (SILAR) and chemical bath deposition (CBD) method. Cadmium Sulphide (CdS) nanoparticles are sensitized over ZnO thin films using SILAR method. The synthesized nanostructured CdS/ZnO heterojunction thin films was characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), High resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), UV-Vis spectroscopy and Raman spectroscopy techniques. The band gap of CdS nanoparticles over ZnO nanostructure was found to be about 3.20 eV. The photocatalytic activities of the deposited CdS/ZnO thin films were evaluated by the degradation of methylene blue (MB) in an aqueous solution under sun light irradiation.

METHOD OF MAKING ALLOYS OF SECOND RARE EARTH SERIES METALS

DOEpatents

Baker, R.D.; Hayward, B.R.

1963-01-01

>This invention relates to a process for alloying the second rare earth series metals with Mo, Nb, or Zr. A halide of the rare earth metal is mixed with about 1 to 20 at.% of an oxide of Mo, Nb, or Zr. Iodine and an alkali or alkaline earth metal are added, and the resulting mixture is heated in an inert atmosphere to 350 deg C. (AEC)

Purification of used eutectic (LiCl-KCl) salt electrolyte from pyroprocessing

NASA Astrophysics Data System (ADS)

Cho, Yung-Zun; Lee, Tae-Kyo; Eun, Hee-Chul; Choi, Jung-Hoon; Kim, In-Tae; Park, Geun-Il

2013-06-01

The separation characteristics of surrogate rare-earth fission products in a eutectic (LiCl-KCl) molten salt were investigated. This system is based on the eutectic salt used for the pyroprocessing treatment of used nuclear fuel (UNF). The investigation was performed using an integrated rare-earth separation apparatus comprising a precipitation reactor, a solid detachment device, and a layer separation device. To separate rare-earth fission products, a phosphate precipitation method using both Li3PO4 and K3PO4 as a precipitant was performed. The use of an equivalent phosphate precipitant composed of 0.408 molar ratio-K3PO4 and 0.592 molar ratio-Li3PO4 can preserve the original eutectic ratio, LiCl-0.592 molar ratio (or 45.2 wt%), as well as provide a high separation efficiency of over 99.5% under conditions of 550 °C and Ar sparging when using La, Nd, Ce, and Pr chlorides. The mixture of La, Nd, Ce, and Pr phosphate had a typical monoclinic (or monazite) structure, which has been proposed as a reliable host matrix for the permanent disposal of a high-level waste form. To maximize the reusability of purified eutectic waste salt after rare-earth separation, the successive rare-earth separation process, which uses both phosphate precipitation and an oxygen sparging method, were introduced and tested with eight rare-earth (Y, La, Ce, Pr, Nd, Sm, Eu and Gd) chlorides. In the successive rare-earth separation process, the phosphate reaction was terminated within 1 h at 550 °C, and a 4-8 h oxygen sparging time were required to obtain over a 99% separation efficiency at 700-750 °C. The mixture of rare-earth precipitates separated by the successive rare-earth separation process was found to be phosphate, oxychloride, and oxide. Through the successive rare-earth separation process, the eutectic ratio of purified salt maintained its original value, and impurity content including the residual precipitant of purified salt can be minimized.

Prospective analysis of the flows of certain rare earths in Europe at the 2020 horizon.

PubMed

Rollat, Alain; Guyonnet, Dominique; Planchon, Mariane; Tuduri, Johann

2016-03-01

This paper proposes a forecast of certain rare earth flows in Europe at the 2020 horizon, based on an analysis of trends influencing various actors of the rare earth industry along the value chain. While 2020 is indicated as the forecast horizon, the analysis should be considered as more representative of the next decade. The rare earths considered here are used in applications that are important for a low-carbon energy transition and/or have a significant recycling potential: NdFeB magnets (Pr, Nd, Dy), NiMH batteries (Pr, Nd) and fluorescent lamp phosphors (Eu, Tb, Y). An analysis of major trends affecting the rare earth industry in Europe along the value chain (including extraction, separation, fabrication, manufacture, use and recycling), helps to build a scenario for a material flow analysis of these rare earths in Europe. The scenario assumes in particular that during the next decade, there exists a rare earth mine in production in Europe (with Norra Kärr in Sweden as a most likely candidate) and also that recycling is in line with targets proposed in recent European legislation. Results are presented in the form of Sankey diagrams which help visualize the various flows for the three applications. For example, calculations forecast flows from extraction to separation of Pr, Nd and Dy for magnet applications in Europe, on the order of 310 tons, 980 tons and 80 tons rare earth metal resp., while recycled flows are 35 tons, 110 tons and 30 tons resp. Calculations illustrate how the relative contribution of recycling to supply strongly depends on the situation with respect to demand. Considering the balance between supply and demand, it is not anticipated any significant shortage of rare earth supply in Europe at the 2020 horizon, barring any new geopolitical crisis involving China. For some heavy rare earths, supply will in fact largely outweigh demand, as for example Europium due to the phasing out of fluorescent lights by LEDs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Osmium mass balance in peridotite and the effects of mantle-derived sulphides on basalt petrogenesis

NASA Astrophysics Data System (ADS)

Harvey, J.; Dale, C. W.; Gannoun, A.; Burton, K. W.

2011-10-01

Analyses of enriched mantle (EM)-basalts, using lithophile element-based isotope systems, have long provided evidence for discrete mantle reservoirs with variable composition. Upon partial melting, the mantle reservoir imparts its isotopic fingerprint upon the partial melt produced. However, it has increasingly been recognised that it may not be simple to delimit these previously well-defined mantle reservoirs; the "mantle zoo" may contain more reservoirs than previously envisaged. Here we demonstrate that a simple model with varying contributions from two populations of compositionally distinct mantle sulphides can readily account for the observed heterogeneities in Os isotope systematics of such basalts without additional mantle reservoirs. Osmium elemental and isotopic analyses of individual sulphide grains separated from spinel lherzolites from Kilbourne Hole, New Mexico, USA demonstrate that two discrete populations of mantle sulphide exist in terms of both Re-Os systematics and textural relationship with co-existing silicates. One population, with a rounded morphology, is preserved in silicate grains and typically possesses high [Os] and low [Re] with unradiogenic, typically sub-chondritic 187Os/ 188Os attributable to long term isolation in a low-Re environment. By contrast, irregular-shaped sulphides, preserved along silicate grain boundaries, possess low [Os], higher [Re] and a wider range of, but generally supra-chondritic 187Os/ 188Os ([Os] typically ⩽ 1-2 ppm, 187Os/ 188Os ⩽ 0.3729; this study). This population is thought to represent metasomatic sulphide. Uncontaminated silicate phases contain negligible Os (<100 ppt) therefore the Os elemental and isotope composition of basalts is dominated by volumetrically insignificant sulphide ([Os] ⩽ 37 ppm; this study). During the early stages of partial melting, supra-chondritic interstitial sulphides are mobilised and incorporated into the melt, adding their radiogenic 187Os/ 188Os signature. Only when sulphides armoured within silicates are exposed to the melt through continued partial melting will enclosed sulphides add their high [Os] and unradiogenic 187Os/ 188Os to the aggregate melt. Platinum-group element data for whole rocks are also consistent with this scenario. The sequence of (i) addition of all of the metasomatic sulphide, followed by (ii) the incorporation of small amounts of armoured sulphide can thus account for the range of both [Os] and 187Os/ 188Os of EM-basalts worldwide without the need for contributions from additional silicate mantle reservoirs.

Reverse engineering nuclear properties from rare earth abundances in the r process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mumpower, Matthew Ryan; McLaughlin, G. C.; Surman, R.

The bulk of the rare earth elements are believed to be synthesized in the rapid neutron capture process or r process of nucleosynthesis. The solar r-process residuals show a small peak in the rare earths aroundmore » $$A\\sim 160$$, which is proposed to be formed dynamically during the end phase of the r process by a pileup of material. This abundance feature is of particular importance as it is sensitive to both the nuclear physics inputs and the astrophysical conditions of the main r process. Here, we explore the formation of the rare earth peak from the perspective of an inverse problem, using Monte Carlo studies of nuclear masses to investigate the unknown nuclear properties required to best match rare earth abundance sector of the solar isotopic residuals. When nuclear masses are changed, we recalculate the relevant β-decay properties and neutron capture rates in the rare earth region. The feedback provided by this observational constraint allows for the reverse engineering of nuclear properties far from stability where no experimental information exists. We investigate a range of astrophysical conditions with this method and show how these lead to different predictions in the nuclear properties influential to the formation of the rare earth peak. Finally, we conclude that targeted experimental campaigns in this region will help to resolve the type of conditions responsible for the production of the rare earth nuclei, and will provide new insights into the longstanding problem of the astrophysical site(s) of the r process.« less

Reverse engineering nuclear properties from rare earth abundances in the r process

DOE PAGES

Mumpower, Matthew Ryan; McLaughlin, G. C.; Surman, R.; ...

2017-02-01

The bulk of the rare earth elements are believed to be synthesized in the rapid neutron capture process or r process of nucleosynthesis. The solar r-process residuals show a small peak in the rare earths aroundmore » $$A\\sim 160$$, which is proposed to be formed dynamically during the end phase of the r process by a pileup of material. This abundance feature is of particular importance as it is sensitive to both the nuclear physics inputs and the astrophysical conditions of the main r process. Here, we explore the formation of the rare earth peak from the perspective of an inverse problem, using Monte Carlo studies of nuclear masses to investigate the unknown nuclear properties required to best match rare earth abundance sector of the solar isotopic residuals. When nuclear masses are changed, we recalculate the relevant β-decay properties and neutron capture rates in the rare earth region. The feedback provided by this observational constraint allows for the reverse engineering of nuclear properties far from stability where no experimental information exists. We investigate a range of astrophysical conditions with this method and show how these lead to different predictions in the nuclear properties influential to the formation of the rare earth peak. Finally, we conclude that targeted experimental campaigns in this region will help to resolve the type of conditions responsible for the production of the rare earth nuclei, and will provide new insights into the longstanding problem of the astrophysical site(s) of the r process.« less

Manganese Health Research Program (MHRP)

DTIC Science & Technology

2008-01-01

NO3)2 Manganese sulphate or Manganese (II) sulphate – MnSO4 Manganese sulphide or Manganese (II) sulphide – MnS Manganese oxide – MnO Barium... sulphide or Manganese (II) sulphide – MnS 1344-43-0 Manganese oxide – MnO 7787-35-1 Barium manganate - BaMnO4 10294-64-1 Potassium manganate – K2MnO4...Characterization of welding fumes and their potential neurotoxic effects. International Workshop: Neurotoxic Metals- Lead, Mercury , and Manganese

Ames Lab 101: Rare-Earth Recycling

ScienceCinema

Ryan Ott

2017-12-22

Recycling keeps paper, plastics, and even jeans out of landfills. Could recycling rare-earth magnets do the same? Perhaps, if the recycling process can be improved. Scientists at the U.S. Department of Energy's Ames Laboratory are working to more effectively remove the neodymium, a rare earth, from the mix of other materials in a magnet.

Effect of the addition of low rare earth elements (lanthanum, neodymium, cerium) on the biodegradation and biocompatibility of magnesium.

PubMed

Willbold, Elmar; Gu, Xuenan; Albert, Devon; Kalla, Katharina; Bobe, Katharina; Brauneis, Maria; Janning, Carla; Nellesen, Jens; Czayka, Wolfgang; Tillmann, Wolfgang; Zheng, Yufeng; Witte, Frank

2015-01-01

Rare earth elements are promising alloying element candidates for magnesium alloys used as biodegradable devices in biomedical applications. Rare earth elements have significant effects on the high temperature strength as well as the creep resistance of alloys and they improve magnesium corrosion resistance. We focused on lanthanum, neodymium and cerium to produce magnesium alloys with commonly used rare earth element concentrations. We showed that low concentrations of rare earth elements do not promote bone growth inside a 750 μm broad area around the implant. However, increased bone growth was observed at a greater distance from the degrading alloys. Clinically and histologically, the alloys and their corrosion products caused no systematic or local cytotoxicological effects. Using microtomography and in vitro experiments, we could show that the magnesium-rare earth element alloys showed low corrosion rates, both in in vitro and in vivo. The lanthanum- and cerium-containing alloys degraded at comparable rates, whereas the neodymium-containing alloy showed the lowest corrosion rates. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Are C1 chondrites chemically fractionated - A trace element study

NASA Technical Reports Server (NTRS)

Ebihara, M.; Wolf, R.; Anders, E.

1982-01-01

Six C1 chondrite samples and a C2 xenolith from the Plainview H5 chondrite were analyzed by radiochemical neutron activation for a large variety of elements, including rare earths. The sample processing is described, including the irradiation, chemical procedure, rare earths separation, counting techniques, radiochemical purity check, and chemical yields. The results of consistency checks on a number of elements are discussed. Abundances for siderophiles, volatiles, and rare earths are presented and discussed. Tests are presented for fractionation of rare earths and other refractories, compositional uniformity of C1's, and interelement correlations. There is no conclusive evidence for nebular fractionation affecting C1's. Three fractionation-prone rare earths have essentially the same relative abundances in C1's and all other chondrite classes, and hence are apparently not fractionated in C1's.

Assessment of Trading Partners for China's Rare Earth Exports Using a Decision Analytic Approach

PubMed Central

He, Chunyan; Lei, Yalin; Ge, Jianping

2014-01-01

Chinese rare earth export policies currently result in accelerating its depletion. Thus adopting an optimal export trade selection strategy is crucial to determining and ultimately identifying the ideal trading partners. This paper introduces a multi-attribute decision-making methodology which is then used to select the optimal trading partner. In the method, an evaluation criteria system is established to assess the seven top trading partners based on three dimensions: political relationships, economic benefits and industrial security. Specifically, a simple additive weighing model derived from an additive utility function is utilized to calculate, rank and select alternatives. Results show that Japan would be the optimal trading partner for Chinese rare earths. The criteria evaluation method of trading partners for China's rare earth exports provides the Chinese government with a tool to enhance rare earth industrial policies. PMID:25051534

RECOVERY OF THORIUM AND URANIUM VALUES FROM AQUEOUS SOLUTIONS

DOEpatents

Calkins, G.D.

1958-02-18

This patent deals with the separation and recovery of uranium from monazite sand. After initial treatment of the sand with sodium hydroxide, a precipitate is obtuined which contains the uranium, thorium, rare earths and some phosphorus. This precipitate is then dissolved in nitric acid. The bulk of the rare earths are removed from thls soiution by adding aa excess of alkali carbonate, causing precipitation of the rare earths together with part of the thorium present. The solution still contains a considerable amount of thorium, some rare earths, and practically all of the uranium originally present. Thorium and rare earth values are readily precipitated from such solution, and the uranium values thus isolated, by the addition of an excess hydrogen peroxide. The pH value of the solution is preferably adjusted to at least 9 prior to the addition of the peroxide.

Assessment of trading partners for China's rare earth exports using a decision analytic approach.

PubMed

He, Chunyan; Lei, Yalin; Ge, Jianping

2014-01-01

Chinese rare earth export policies currently result in accelerating its depletion. Thus adopting an optimal export trade selection strategy is crucial to determining and ultimately identifying the ideal trading partners. This paper introduces a multi-attribute decision-making methodology which is then used to select the optimal trading partner. In the method, an evaluation criteria system is established to assess the seven top trading partners based on three dimensions: political relationships, economic benefits and industrial security. Specifically, a simple additive weighing model derived from an additive utility function is utilized to calculate, rank and select alternatives. Results show that Japan would be the optimal trading partner for Chinese rare earths. The criteria evaluation method of trading partners for China's rare earth exports provides the Chinese government with a tool to enhance rare earth industrial policies.

Automated classification of Acid Rock Drainage potential from Corescan drill core imagery

NASA Astrophysics Data System (ADS)

Cracknell, M. J.; Jackson, L.; Parbhakar-Fox, A.; Savinova, K.

2017-12-01

Classification of the acid forming potential of waste rock is important for managing environmental hazards associated with mining operations. Current methods for the classification of acid rock drainage (ARD) potential usually involve labour intensive and subjective assessment of drill core and/or hand specimens. Manual methods are subject to operator bias, human error and the amount of material that can be assessed within a given time frame is limited. The automated classification of ARD potential documented here is based on the ARD Index developed by Parbhakar-Fox et al. (2011). This ARD Index involves the combination of five indicators: A - sulphide content; B - sulphide alteration; C - sulphide morphology; D - primary neutraliser content; and E - sulphide mineral association. Several components of the ARD Index require accurate identification of sulphide minerals. This is achieved by classifying Corescan Red-Green-Blue true colour images into the presence or absence of sulphide minerals using supervised classification. Subsequently, sulphide classification images are processed and combined with Corescan SWIR-based mineral classifications to obtain information on sulphide content, indices representing sulphide textures (disseminated versus massive and degree of veining), and spatially associated minerals. This information is combined to calculate ARD Index indicator values that feed into the classification of ARD potential. Automated ARD potential classifications of drill core samples associated with a porphyry Cu-Au deposit are compared to manually derived classifications and those obtained by standard static geochemical testing and X-ray diffractometry analyses. Results indicate a high degree of similarity between automated and manual ARD potential classifications. Major differences between approaches are observed in sulphide and neutraliser mineral percentages, likely due to the subjective nature of manual estimates of mineral content. The automated approach presented here for the classification of ARD potential offers rapid, repeatable and accurate outcomes comparable to manually derived classifications. Methods for automated ARD classifications from digital drill core data represent a step-change for geoenvironmental management practices in the mining industry.

Melt containment member

DOEpatents

Rieken, Joel R.; Heidloff, Andrew J.

2014-09-09

A tubular melt containment member for transient containment of molten metals and alloys, especially reactive metals and alloys, includes a melt-contacting layer or region that comprises an oxygen-deficient rare earth oxide material that is less reactive as compared to the counterpart stoichiometric rare earth oxide. The oxygen-deficient (sub-stoichiometric) rare earth oxide can comprise oxygen-deficient yttria represented by Y.sub.2O.sub.3-x wherein x is from 0.01 to 0.1. Use of the oxygen-deficient rare earth oxide as the melt-contacting layer or region material reduces reaction with the melt for a given melt temperature and melt contact time.

Rare earth gas laser

DOEpatents

Krupke, W.F.

1975-10-31

A high energy gas laser with light output in the infrared or visible region of the spectrum is described. Laser action is obtained by generating vapors of rare earth halides, particularly neodymium iodide or, to a lesser extent, neodymium bromide, and disposing the rare earth vapor medium in a resonant cavity at elevated temperatures; e.g., approximately 1200/sup 0/ to 1400/sup 0/K. A particularly preferred gaseous medium is one involving a complex of aluminum chloride and neodymium chloride, which exhibits tremendously enhanced vapor pressure compared to the rare earth halides per se, and provides comparable increases in stored energy densities.

Short-term effect of strontium- and zinc-containing toothpastes and mouthrinses on volatile sulphur compounds in morning breath: a randomized, double-blind, cross-over clinical study.

PubMed

Soares, Léo G; Jonski, Grazyna; Tinoco, Eduardo M B; Young, Alix

2015-04-01

Zinc (Zn) reduces the formation of volatile sulphur compounds (VSCs) associated with oral malodour. Although strontium (Sr) is included in some products for reducing dental hypersensitivity, it may also have anti-halitosis properties. This randomized, double-blind, cross-over clinical study compared the anti-VSC effect of brushing with commercial toothpastes and rinses containing Zn and Sr. The volunteers (n = 30) either brushed/rinsed with/without tongue brushing using Zn-containing toothpaste/rinse, Sr-containing toothpaste/rinse, or placebo (control). Volatile sulphur compounds [hydrogen sulphide (H2 S) and methyl mercaptan (CH3 SH)] were measured, in morning breath, using gas chromatography. The anti-VSC effects of the test toothpastes and test rinses were significantly better than the anti-VSC effects of the respective controls. Toothbrushing with test toothpastes gave median reductions, compared with the control, of 70% for H2 S and 55-57% for CH3 SH. Rinsing with the Sr- and Zn-containing solutions had the same anti-VSC effect as toothbrushing and tooth- and tongue brushing with the Sr- and Zn-containing toothpastes. Zinc-containing rinse resulted in a significantly higher median salivary level of Zn compared with brushing with Zn-containing toothpaste, although this effect did not correlate with the anti-VSC effect. It can be concluded that the Sr- and Zn-containing toothpastes and the Zn- and Sr-containing rinses, when used in the evening, are equally effective in reducing morning-breath VSCs the following day. © 2015 Eur J Oral Sci.

Perspectives on Permanent Magnetic Materials for Energy Conversion and Power Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, LH; Jimenez-Villacorta, F

2012-07-18

Permanent magnet development has historically been driven by the need to supply larger magnetic energy in ever smaller volumes for incorporation in an enormous variety of applications that include consumer products, transportation components, military hardware, and clean energy technologies such as wind turbine generators and hybrid vehicle regenerative motors. Since the 1960s, the so-called rare-earth "supermagnets," composed of iron, cobalt, and rare-earth elements such as Nd, Pr, and Sm, have accounted for the majority of global sales of high-energy-product permanent magnets for advanced applications. In rare-earth magnets, the transition-metal components provide high magnetization, and the rare-earth components contribute a verymore » large magnetocrystalline anisotropy that donates high resistance to demagnetization. However, at the end of 2009, geopolitical influences created a worldwide strategic shortage of rare-earth elements that may be addressed, among other actions, through the development of rare-earth-free magnetic materials harnessing sources of magnetic anisotropy other than that provided by the rare-earth components. Materials engineering at the micron scale, nanoscale, and Angstrom scales, accompanied by improvements in the understanding and characterization of nanoscale magnetic phenomena, is anticipated to result in new types of permanent magnetic materials with superior performance. DOI: 10.1007/s11661-012-1278-2 (C) The Minerals, Metals & Materials Society and ASM International 2012« less

Rare earth element recycling from waste nickel-metal hydride batteries.

PubMed

Yang, Xiuli; Zhang, Junwei; Fang, Xihui

2014-08-30

With an increase in number of waste nickel-metal hydride batteries, and because of the importance of rare earth elements, the recycling of rare earth elements is becoming increasingly important. In this paper, we investigate the effects of temperature, hydrochloric acid concentration, and leaching time to optimize leaching conditions and determine leach kinetics. The results indicate that an increase in temperature, hydrochloric acid concentration, and leaching time enhance the leaching rate of rare earth elements. A maximum rare earth elements recovery of 95.16% was achieved at optimal leaching conditions of 70°C, solid/liquid ratio of 1:10, 20% hydrochloric acid concentration, -74μm particle size, and 100min leaching time. The experimental data were best fitted by a chemical reaction-controlled model. The activation energy was 43.98kJ/mol and the reaction order for hydrochloric acid concentration was 0.64. The kinetic equation for the leaching process was found to be: 1-(1-x)(1/3)=A/ρr0[HCl](0.64)exp-439,8008.314Tt. After leaching and filtration, by adding saturated oxalic solution to the filtrate, rare earth element oxalates were obtained. After removing impurities by adding ammonia, filtering, washing with dilute hydrochloric acid, and calcining at 810°C, a final product of 99% pure rare earth oxides was obtained. Copyright © 2014 Elsevier B.V. All rights reserved.

Addressing Rare-Earth Element Criticality: An Example from the Aviation Industry

NASA Astrophysics Data System (ADS)

Ku, Anthony Y.; Dosch, Christopher; Grossman, Theodore R.; Herzog, Joseph L.; Maricocchi, Antonio F.; Polli, Drew; Lipkin, Don M.

2014-11-01

Rare-earth (RE) elements are enablers for a wide range of technologies, including high-strength permanent magnets, energy-efficient lighting, high-temperature thermal barrier coatings, and catalysts. While direct material substitution is difficult in many of these applications because of the specific electronic, optical, or electrochemical properties imparted by the individual rare-earth elements, we describe an example from the aviation industry where supply chain optimization may be an option. Ceramic matrix composite engine components require environmental barrier coatings (EBCs) to protect them from extreme temperatures and adverse reactions with water vapor in the hot gas path. EBC systems based on rare-earth silicates offer a unique combination of environmental resistance, thermal expansion matching, thermal conductivity, and thermal stability across the service temperature window. Several pure rare-earth silicates and solid solutions have been demonstrated in EBC applications. However, all rely on heavy rare-earth elements (HREEs) for phase stability. This article considers the possibility of using separation tailings containing a mixture of HREEs as a source material in lieu of using the high-purity HREE oxides. This option arises because the desired properties of RE-silicate EBCs derive from the average cation size rather than the electronic properties of the individual rare-earth cations. Because separation tailings have not incurred the costs associated with the final stages of separation, they offer an economical alternative to high-purity oxides for this emerging application.

Nano rare-earth oxides induced size-dependent vacuolization: an independent pathway from autophagy

PubMed Central

Zhang, Ying; Yu, Chenguang; Huang, Guanyi; Wang, Changli; Wen, Longping

2010-01-01

Four rare earth oxides have been shown to induce autophagy. Interestingly, we often noticed plentiful vacuolization, which was not always involved in this autophagic process. In this study, we investigated three other rare-earth elements, including Yttrium (Y), Ytterbium (Yb), and Lanthanum (La). Autophagic effect could be induced by all of them but only Y2O3 and Yb2O3 could cause massive vacuolization. Y2O3 and Yb2O3 treated by sonication or centrifugation to reduce particle size were used to test vacuolization level in HeLa cell lines. The results showed that rare earth oxides-induced vacuolization is size-dependent and differs from autophagic pathway. To further clarify the characteristics of this autophagic process, we used MEF Atg-5 (autophagy associated gene 5) knockout cell line, and the result showed that the autophagic process induced by rare earth oxides is Atg-5-dependent and the observed vacuolization was independent from autophagy. Similar results could also be observed in our tests on 3-methyladenine(3-MA), a well-known autophagy inhibitor. In conclusion, for the first time, we clarified the relationship between massive vacuolization and autophagic process induced by rare earth oxides and pointed out the size effect of rare earth oxides on the formation of vacuoles, which give clues to further investigation on the mechanisms underlying their biological effects. PMID:20856835

Nano rare-earth oxides induced size-dependent vacuolization: an independent pathway from autophagy.

PubMed

Zhang, Ying; Yu, Chenguang; Huang, Guanyi; Wang, Changli; Wen, Longping

2010-09-07

Four rare earth oxides have been shown to induce autophagy. Interestingly, we often noticed plentiful vacuolization, which was not always involved in this autophagic process. In this study, we investigated three other rare-earth elements, including Yttrium (Y), Ytterbium (Yb), and Lanthanum (La). Autophagic effect could be induced by all of them but only Y(2)O(3) and Yb(2)O(3) could cause massive vacuolization. Y(2)O(3) and Yb(2)O(3) treated by sonication or centrifugation to reduce particle size were used to test vacuolization level in HeLa cell lines. The results showed that rare earth oxides-induced vacuolization is size-dependent and differs from autophagic pathway. To further clarify the characteristics of this autophagic process, we used MEF Atg-5 (autophagy associated gene 5) knockout cell line, and the result showed that the autophagic process induced by rare earth oxides is Atg-5-dependent and the observed vacuolization was independent from autophagy. Similar results could also be observed in our tests on 3-methyladenine(3-MA), a well-known autophagy inhibitor. In conclusion, for the first time, we clarified the relationship between massive vacuolization and autophagic process induced by rare earth oxides and pointed out the size effect of rare earth oxides on the formation of vacuoles, which give clues to further investigation on the mechanisms underlying their biological effects.

The rapid size- and shape-controlled continuous hydrothermal synthesis of metal sulphide nanomaterials

NASA Astrophysics Data System (ADS)

Dunne, Peter W.; Starkey, Chris L.; Gimeno-Fabra, Miquel; Lester, Edward H.

2014-01-01

Continuous flow hydrothermal synthesis offers a cheap, green and highly scalable route for the preparation of inorganic nanomaterials which has predominantly been applied to metal oxide based materials. In this work we report the first continuous flow hydrothermal synthesis of metal sulphide nanomaterials. A wide range of binary metal sulphides, ZnS, CdS, PbS, CuS, Fe(1-x)S and Bi2S3, have been synthesised. By varying the reaction conditions two different mechanisms may be invoked; a growth dominated route which permits the formation of nanostructured sulphide materials, and a nucleation driven process which produces nanoparticles with temperature dependent size control. This offers a new and industrially viable route to a wide range of metal sulphide nanoparticles with facile size and shape control.Continuous flow hydrothermal synthesis offers a cheap, green and highly scalable route for the preparation of inorganic nanomaterials which has predominantly been applied to metal oxide based materials. In this work we report the first continuous flow hydrothermal synthesis of metal sulphide nanomaterials. A wide range of binary metal sulphides, ZnS, CdS, PbS, CuS, Fe(1-x)S and Bi2S3, have been synthesised. By varying the reaction conditions two different mechanisms may be invoked; a growth dominated route which permits the formation of nanostructured sulphide materials, and a nucleation driven process which produces nanoparticles with temperature dependent size control. This offers a new and industrially viable route to a wide range of metal sulphide nanoparticles with facile size and shape control. Electronic supplementary information (ESI) available: Experimental details, refinement procedure, fluorescence spectra of ZnS samples. See DOI: 10.1039/c3nr05749f

Nickel and its isotopes in organic-rich sediments: implications for oceanic budgets and a potential record of ancient seawater

NASA Astrophysics Data System (ADS)

Ciscato, Emily R.; Bontognali, Tomaso R. R.; Vance, Derek

2018-07-01

Nickel (Ni) is a biologically active element that displays a nutrient-like depth distribution in the modern oceans. Recent studies of Ni isotopes have highlighted the fact that, in common with many other transition metals, the Ni stable isotope composition, expressed as δ60Ni, of the dissolved phase is heavier than the inputs, at +1.3 to +1.7‰. The sedimentary outputs that control the high δ60Ni of the ocean, coupled with records for past seawater, could potentially yield new information on the past Earth system, but these are currently not well understood. Here we present the first Ni abundance and isotope data for a key output, that associated with Ni uptake into organic matter, at productive upwelling regions and elsewhere. We investigate the distribution of Ni and its isotopes in two fractions separated from the bulk sediment, an HF-digestible fraction, extracted with HF-HCl, and an organic-sulphide-rich fraction. The organic-sulphide fractions exhibit a range in δ60Ni, from +0.86 to +1.83. Systematic relationships between Ni concentrations, total organic carbon and Ni isotopes suggest that the organic-sulphide fraction originates in the photic zone, and is delivered to the sediment as a closed system, despite the possibility of transfer of Ni to sulphide within it. Authigenic Ni in the bulk sediment is dominated by the HF-digestible fraction which, in Ni-enriched sediments where the detrital correction is small, is very close to the modern deep ocean, at δ60Ni = +1.2‰. These data suggest that organic-rich sediments beneath upwelling zones, while they are an important output flux of Ni from the oceans, do not solve the isotope balance problem because their δ60Ni is almost identical to modern seawater. On the other hand, the approach adopted here involving the analysis of the two fractions, both traces the fractionation imparted by biological uptake as well as recording the δ60Ni of contemporary seawater, suggesting potential for understanding the past oceans.

Geologic setting of the Mountain Pass rare earth deposits, San Bernardino County, California

USGS Publications Warehouse

Olson, Jerry Chipman

1952-01-01

The Mountain Pass district is in a block of pre-Cambrian metamorphic rocks bounded on the east and south by the alluvium of Ivanpah Valley. This block is separated from Paleozoic and Mesozoic sedimentary and volcanic rocks on the west by the Clark Mountain normal fault, and the northern boundary of the district is a prominent transverse fault. The pre-Cambrian metamorphic complex comprises a great variety of lithologic types including garnetiferous mica gneisses and schists; biotite-garnet-sillimenite gneiss; hornblende gneiss, schist, and amphibolite; biotite gneiss and schist; granitic gneisses and migmatites; pegmatites; and minor amounts of foliated mafic rocks. The rare earth-bearing carbonate rocks are related to potash-rich igneous rocks, of uncertain age, that cut the metamorphic complex. The larger potash-rich intrusive masses, 300 or more feet wide, comprise one granite, two syenite, and four composite shonkinite-syenite bodies. One of the shonkinite-syenite stocks is more than a mile long. Several hundred relatively thin dikes of these potash-rich rocks range in composition, and generally decreasing age, from biotite shonkinite through syenite to granite. A few thin fine-grained shonkinite dikes cut the granite. These potash-rich rocks are cut by east-trending andesitic dikes and by faults. Veins of carbonate rock are most abundant in and near the southwest side of the largest shonkinite-syenite body. Although most veins are less than 6 feet thick, one mass of carbonate rock near the Sulphide Queen min4e is 600 feet in maximum width and 2,400 feet long. About 200 veins have been mapped in the district; their aggregate surface area is probably less than one-tenth that of the large carbonate mass. The carbonate materials, which make up about 60 percent of the veins and the large carbonite body, are chiefly calcite, dolomite, ankerite, and siderite. The other constituents are barite, bastnaesite and perisite, quartz, and variable small quantities of crocidolite, biotite, phlogopite, chlorite, muscovite, apatite, iron oxides, fluorite, monazite, galena, allanite, sphene, pyrite, chalcopyrite, tetrahedrite, malachite, azurite, corussite, wulfenite, aragonite, and thorite. The rare earth oxide content in most of the carbonate rock is less than 13 percent, but in some local concentrations of bastnaesite the content is as high as 40 percent. The origin of the carbonate rocks and related potash-rich igneous rocks is considered in the light of similar associations of carbonate and alkalinic rocks in Sweden, Norway, Russia, South Africa, and the United States. The carbonate rock may have originated (1) as a pre-Cambrian limestone or evaporate sequence in the gneisses; (2) by reaction between magma and the Paleozoic dolomite and limestone overlying the pre-Cambrian complex; (3) by alteration of pre-Cambrian gneisses by emanations from an unknown deep-seated source; or (4) by differentiation of an alkaline magma from shonkinite to syenite to granite, leading to a final carbonate-rich fraction, containing the rare elements, which was emplaced either as a concentrated or a dilute solution. The fourth hypothesis is considered the most plausible.

Ternary rare earth-lanthanide sulfides

DOEpatents

Takeshita, Takuo; Gschneidner, Jr., Karl A.; Beaudry, Bernard J.

1987-01-06

A new ternary rare earth sulfur compound having the formula: La.sub.3-x M.sub.x S.sub.4 where M is a rare earth element selected from the group europium, samarium and ytterbium and x=0.15 to 0.8. The compound has good high-temperature thermoelectric properties and exhibits long-term structural stability up to 1000.degree. C.

Abrasive wear behavior of in-situ RZ5-10wt%TiC composite

NASA Astrophysics Data System (ADS)

Mehra, Deepak; Mahapatra, M. M.; Harsha, S. P.

2018-05-01

RZ5 Magnesium alloys containing zinc, rare earth and zirconium are well-known to have high specific strength, good creep resistance widely used in aerospace components. The incorporation of hard ceramic strengthens RZ5 mg alloy. The RZ5-10wt%TiC composite has been fabricated in situ using RZ5 mg alloy as matrix and TiC as reinforcement by self propagating high temperature synthesis (SHS) technique. This paper investigates the abrasive wear behavior of RZ5-10wt%TiC. Tests were performed using pin-on-disc apparatus against 600 grit abrasive paper by varying the sliding distance and applied load. The results showed improvement in the wear resistance of testing composite as compared to the unreinforced RZ5 Mg alloy. The coefficient of friction and weight loss increased linearly as applied load and sliding distance increased. The field emission scanning electron microscopic (FESEM) showed dominate wear mechanisms: abrasion, ploughing grooves.

EnGeoMAP - geological applications within the EnMAP hyperspectral satellite science program

NASA Astrophysics Data System (ADS)

Boesche, N. K.; Mielke, C.; Rogass, C.; Guanter, L.

2016-12-01

Hyperspectral investigations from near field to space substantially contribute to geological exploration and mining monitoring of raw material and mineral deposits. Due to their spectral characteristics, large mineral occurrences and minefields can be identified from space and the spatial distribution of distinct proxy minerals be mapped. In the frame of the EnMAP hyperspectral satellite science program a mineral and elemental mapping tool was developed - the EnGeoMAP. It contains a basic mineral mapping and a rare earth element mapping approach. This study shows the performance of EnGeoMAP based on simulated EnMAP data of the rare earth element bearing Mountain Pass Carbonatite Complex, USA, and the Rodalquilar and Lomilla Calderas, Spain, which host the economically relevant gold-silver, lead-zinc-silver-gold and alunite deposits. The mountain pass image data was simulated on the basis of AVIRIS Next Generation images, while the Rodalquilar data is based on HyMap images. The EnGeoMAP - Base approach was applied to both images, while the mountain pass image data were additionally analysed using the EnGeoMAP - REE software tool. The results are mineral and elemental maps that serve as proxies for the regional lithology and deposit types. The validation of the maps is based on chemical analyses of field samples. Current airborne sensors meet the spatial and spectral requirements for detailed mineral mapping and future hyperspectral space borne missions will additionally provide a large coverage. For those hyperspectral missions, EnGeoMAP is a rapid data analysis tool that is provided to spectral geologists working in mineral exploration.

Body burden of toxic metals and rare earth elements in non-smokers, cigarette smokers and electronic cigarette users.

PubMed

Badea, Mihaela; Luzardo, Octavio P; González-Antuña, Ana; Zumbado, Manuel; Rogozea, Liliana; Floroian, Laura; Alexandrescu, Dana; Moga, Marius; Gaman, Laura; Radoi, Mariana; Boada, Luis D; Henríquez-Hernández, Luis Alberto

2018-06-13

Smoking is considered an important source for inorganic elements, most of them toxic for human health. During the last years, there has been a significant increase in the use of e-cigarettes, although the role of them as source of inorganic elements has not been well established. A cross-sectional study including a total of 150 subjects from Brasov (Romania), divided into three groups (non-smokers, cigarette smokers and electronic cigarettes smokers) were recruited to disclose the role of smoking on the human exposure to inorganic elements. Concentration of 42 elements, including trace elements, elements in the ATSDR's priority pollutant list and rare earth elements (REE) were measured by ICP-MS in the blood serum of participants. Cigarette smokers showed the highest levels of copper, molybdenum, zinc, antimony, and strontium. Electronic cigarette (e-cigarette) users presented the highest concentrations of selenium, silver, and vanadium. Beryllium, europium and lanthanides were detected more frequently among e-cigarette users (20.6%, 23.5%, and 14.7%) than in cigarette smokers (1.7%, 19.0%, and 12.1%, respectively); and the number of detected REE was also higher among e-cigarette users (11.8% of them showed more than 10 different elements). Serum levels of cerium and erbium increased as the duration of the use of e-cigarettes was longer. We have found that smoking is mainly a source of heavy metals while the use of e-cigarettes is a potential source of REE. However, these elements were detected at low concentrations. Copyright © 2018 Elsevier Inc. All rights reserved.

An Operationally Simple Method for Separating the Rare-Earth Elements Neodymium and Dysprosium.

PubMed

Bogart, Justin A; Lippincott, Connor A; Carroll, Patrick J; Schelter, Eric J

2015-07-06

Rare-earth metals are critical components of electronic materials and permanent magnets. Recycling of consumer materials is a promising new source of rare earths. To incentivize recycling there is a clear need for simple methods for targeted separations of mixtures of rare-earth metal salts. Metal complexes of a tripodal nitroxide ligand [{(2-(t) BuNO)C6 H4 CH2 }3 N](3-) (TriNOx(3-) ), feature a size-sensitive aperture formed of its three η(2) -(N,O) ligand arms. Exposure of metal cations in the aperture induces a self-associative equilibrium comprising [M(TriNOx)thf]/ [M(TriNOx)]2 (M=rare-earth metal). Differences in the equilibrium constants (Keq ) for early and late metals enables simple Nd/Dy separations through leaching with a separation ratio SNd/Dy =359. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Value analysis of neodymium content in shredder feed: toward enabling the feasibility of rare earth magnet recycling.

PubMed

Bandara, H M Dhammika; Darcy, Julia W; Apelian, Diran; Emmert, Marion H

2014-06-17

In order to facilitate the development of recycling technologies for rare earth magnets from postconsumer products, we present herein an analysis of the neodymium (Nd) content in shredder scrap. This waste stream has been chosen on the basis of current business practices for the recycling of steel, aluminum, and copper from cars and household appliances, which contain significant amounts of rare earth magnets. Using approximations based on literature data, we have calculated the average Nd content in the ferrous shredder product stream to be between 0.13 and 0.29 kg per ton of ferrous scrap. A value analysis considering rare earth metal prices between 2002 and 2013 provides values between $1.32 and $145 per ton of ferrous scrap for this material, if recoverable as pure Nd metal. Furthermore, we present an analysis of the content and value of other rare earths (Pr, Dy, Tb).

Contributed Review: A review of the investigation of rare-earth dopant profiles in optical fibers.

PubMed

Sidiroglou, F; Roberts, A; Baxter, G

2016-04-01

Rare-earth doped optical fibers have captivated the interest of many researchers around the world across the past three decades. The growth of this research field has been stimulated primarily through their application in optical communications as fiber lasers and amplifiers, although rare-earth doped optical fiber based devices are now finding important uses in many other scientific and industrial areas (for example, medicine, sensing, the military, and material processing). Such wide commercial interest has provided a strong incentive for innovative fiber designs, alternative glass compositions, and novel fabrication processes. A prerequisite for the ongoing progress of this research field is developing the capacity to provide high resolution information about the rare-earth dopant distribution profiles within the optical fibers. This paper constitutes a comprehensive review of the imaging techniques that have been utilized in the analysis of the distribution of the rare-earth ion erbium within the core of optical fibers.

Loparite, a rare-earth ore (Ce, Na, Sr, Ca)(Ti, Nb, Ta, Fe+3)O3

USGS Publications Warehouse

Hedrick, James B.; Sinha, Shyama P.; Kosynkin, Valery D.

1997-01-01

The mineral loparite (Ce, NA, Sr, Ca)(Ti, Nb, Ta, Fe+3)O3 is the principal ore of the light-group rare-earth elements (LREE) in Russia. The complex oxide has a perovskite (ABO3) structure with coupled substitutions, polymorphism, defect chemistry and a tendency to become metamict. The A site generally contains weakly bonded, easily exchanged cations of the LREE, Na and Ca. The B site generally contains smaller, highly charged cations of Ti, Nb or Fe+3. Mine production is from Russia's Kola Peninsula. Ore is beneficiated to produce a 95% loparite concentrate containing 30% rare-earth oxides. Loparite concentrate is refined by either a chlorination process or acid decomposition process to recover rare-earths, titanium, niobium and tantalum. Rare-earths are separated by solvent extraction and selective precipitation/dissolution. The concentrate is processed at plants in Russia, Estonia and Kazakstan.

Rare earth element scavenging in seawater

NASA Astrophysics Data System (ADS)

Byrne, Robert H.; Kim, Ki-Hyun

1990-10-01

Examinations of rare earth element (REE) adsorption in seawater, using a variety of surface-types, indicated that, for most surfaces, light rare earth elements (LREEs) are preferentially adsorbed compared to the heavy rare earths (HREEs). Exceptions to this behavior were observed only for silica phases (glass surfaces, acid-cleaned diatomaceous earth, and synthetic SiO 2). The affinity of the rare earths for surfaces can be strongly affected by thin organic coatings. Glass surfaces which acquired an organic coating through immersion in Tampa Bay exhibited adsorptive behavior typical of organic-rich, rather than glass, surfaces. Models of rare earth distributions between seawater and carboxylate-rich surfaces indicate that scavenging processes which involve such surfaces should exhibit a strong dependence on pH and carbonate complexation. Scavenging models involving carboxylate surfaces produce relative REE abundance patterns in good general agreement with observed shale-normalized REE abundances in seawater. Scavenging by carboxylate-rich surfaces should produce HREE enrichments in seawater relative to the LREEs and may produce enrichments of lanthanum relative to its immediate trivalent neighbors. Due to the origin of distribution coefficients as a difference between REE solution complexation (which increases strongly with atomic number) and surface complexation (which apparently also increases with atomic number) the relative solution abundance patterns of the REEs produced by scavenging reactions can be quite complex.

X-ray absorption spectroscopy and photoluminescence study of rare earth ions doped strontium sulphide phosphors

NASA Astrophysics Data System (ADS)

Vij, Ankush; Gautam, Sanjeev; Kumar, Vinay; Brajpuriya, R.; Kumar, Ravi; Singh, Nafa; Chae, Keun Hwa

2013-01-01

We present here the electronic structure and photoluminescence properties of Sm (0.1-1.0 mol%) doped SrS phosphors. The doping in SrS was probed by near-edge X-ray absorption fine structure (NEXAFS) at M5,4-edges of Sm in total electron yield mode. The simulated absorption edges using atomic multiplet calculations were correlated with experimental results, which clearly reveal the presence of trivalent state of Sm in SrS matrix. However, for Sm (1 mol%), very minor traces of Sm2+ were also observed, which have been explained by comparing the NEXAFS spectra in total electron and florescence yield mode. The PL emission of SrS:Sm comprises of three sharp bands at 567, 602 and 650 nm owing to the well-known intra 4f transitions from 4G5/2 to 6HJ (J = 5/2, 7/2, 9/2) levels of Sm3+ ions in SrS host. The effect of Ce co-doping on SrS:Sm phosphors was also investigated, which exhibits characteristic PL emission of independent ions at their respective excitation wavelengths. However, at an excitation wavelength of 393 nm, SrS:Ce,Sm exhibits the simultaneous characteristic PL emission of both ions spanning into blue-green-red region. The CIE chromaticity coordinates also clearly show the influence of excitation wavelengths on the emission colour of SrS:Ce,Sm.

Binding Site Configurations Probe the Structure and Dynamics of the Zinc Finger of NEMO (NF-κB Essential Modulator).

PubMed

Godwin, Ryan C; Melvin, Ryan L; Gmeiner, William H; Salsbury, Freddie R

2017-01-31

Zinc-finger proteins are regulators of critical signaling pathways for various cellular functions, including apoptosis and oncogenesis. Here, we investigate how binding site protonation states and zinc coordination influence protein structure, dynamics, and ultimately function, as these pivotal regulatory proteins are increasingly important for protein engineering and therapeutic discovery. To better understand the thermodynamics and dynamics of the zinc finger of NEMO (NF-κB essential modulator), as well as the role of zinc, we present results of 20 μs molecular dynamics trajectories, 5 μs for each of four active site configurations. Consistent with experimental evidence, the zinc ion is essential for mechanical stabilization of the functional, folded conformation. Hydrogen bond motifs are unique for deprotonated configurations yet overlap in protonated cases. Correlated motions and principal component analysis corroborate the similarity of the protonated configurations and highlight unique relationships of the zinc-bound configuration. We hypothesize a potential mechanism for zinc binding from results of the thiol configurations. The deprotonated, zinc-bound configuration alone predominantly maintains its tertiary structure throughout all 5 μs and alludes rare conformations potentially important for (im)proper zinc-finger-related protein-protein or protein-DNA interactions.

Resistivity and magnetoresistivity of amorphous rare-earth alloys

NASA Astrophysics Data System (ADS)

Borchi, E.; Poli, M.; De Gennaro, S.

1982-05-01

The resistivity and magnetoresistivity of amorphous rare-earth alloys are studied starting from the general approach of Van Peski-Tinbergen and Dekker. The random axial crystal-field and the magnetic correlations between the rare-earth ions are consistently taken into account. The characteristic features of the available experimental data are explained both of the case of random ferromagnetic and antiferromagnetic order.

Study of rare earth local moment magnetism and strongly correlated phenomena in various crystal structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kong, Tai

Benefiting from unique properties of 4f electrons, rare earth based compounds are known for offering a versatile playground for condensed matter physics research as well as industrial applications. This thesis focuses on three specific examples that further explore the rare earth local moment magnetism and strongly correlated phenomena in various crystal structures.

COST-EFFECTIVE RARE EARTH ELEMENT RECYCLING PROCESS FROM INDUSTRIAL SCRAP AND DISCARDED ELECTRONIC PRODUCTS TO VALUABLE MAGNETIC ALLOYS AND PERMANENT MAGNETS - PHASE II

EPA Science Inventory

Rare earth element (REE) based Nd-Fe-B and Sm-Co permanent magnets have been widely used because of their excellent magnetic properties. The applications of Nd-Fe-B and Sm-Co rare earth permanent magnets include hybrid electric vehicles (HEVs), power generators for wind tur...

Membrane assisted solvent extraction for rare earth element recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhave, Ramesh R.; Kim, Daejin; Peterson, Eric S.

Systems and methods for the recovery of rare earth elements are provided. The systems and methods generally include membrane assisted solvent extraction using permeable hollow fibers having an immobilized organic phase within the pores of the hollow fibers. The permeable hollow fibers are generally in contact with an acidic aqueous feed on one side thereof and a strip solution on another side thereof. The systems and methods generally include the simultaneous extraction and stripping of rare earth elements as a continuous recovery process that is well suited for post-consumer products, end-of-life products, and other recovery sources of rare earth elements.

Rare earth elements in weathering profiles and sediments of Minnesota: Implications for provenance studies

USGS Publications Warehouse

Morey, G.B.; Setterholm, D.R.

1997-01-01

The relative abundance of rare earth elements in sediments has been suggested as a tool for determining their source rocks. This correlation requires that weathering, erosion, and sedimentation do not alter the REE abundances, or do so in a predictable manner. We find that the rare earth elements are mobilized and fractionated by weathering, and that sediments derived from the weathered materials can display modifications of the original pattern of rare earth elements of some due to grain-size sorting of the weathered material. However, the REE distribution pattern of the provenance terrane can be recognized in the sediments.

Rare-Earth-compound nanowires, nanotubes, and fullerene-like nanoparticles: synthesis, characterization, and properties.

PubMed

Wang, Xun; Li, Yadong

2003-11-21

Various low-dimensional nanostructures, such as nanowires, nanotubes, nanosheets, and fullerene-like nanoparticles have been selectively synthesized from rare-earth compounds (hydroxides, fluorides) based on a facile hydrothermal method. The subsequent dehydration, sulfidation, and fluoridation processes lead to the formation of rare-earth oxide, oxysulfide, and oxyhalide nanostructures, which can be functionalized further by doping with other rare-earth ions or by coating with metal nanoparticles. Owing to the interesting combination of novel nanostructures and functional compounds, these nanostructures can be expected to bring new opportunities in the vast research areas of and application in biology, catalysts, and optoelectronic devices.

Crystallographic phases in heavy rare earth metals under megabar pressures

NASA Astrophysics Data System (ADS)

Samudrala, G. K.; Vohra, Y. K.

2012-07-01

Experiments aimed at understanding the crystallographic phases of heavy rare earth metals were carried out in a diamond anvil cell at the Advanced Photon Source, Argonne National Laboratory. Heavy rare earth metals dysprosium (Dy), holmium (Ho), erbium (Er) and thulium (Tm) were compressed to multi-megabar pressures. The rare earth crystal sequence hcp→Sm-type→dhcp→distorted-fcc (dfcc) is observed in all four elements. Upon further compression, a structural transformation to a monoclinic C2/m phase has been observed. We summarize the results from these experiments and present Rietveld structural refinements on high pressure phases for the specific case of dysprosium.

Fascinating Magnetic Energy Storage Nanomaterials: A Brief Review.

PubMed

Sreenivasulu, Kummari V; Srikanth, Vadali V S S

2017-07-10

In this brief review, the importance of nanotechnology in developing novel magnetic energy storage materials is discussed. The discussion covers recent patents on permanent magnetic materials and especially covers processing of permanent magnets (rare-earth and rare-earth free magnets), importance of rare-earth permanent magnets and necessity of rare-earth free permanent magnets. Magnetic energy storage materials are those magnetic materials which exhibit very high energy product (BH)max (where B is the magnetic induction in Gauss (G) whereas H is the applied magnetic field in Oersted (Oe)). (BH)max is the direct measure of the ability of a magnetic material to store energy. In this context, processing of magnetic energy storage composite materials constituted by soft and hard magnetic materials played a predominant role in achieving high (BH)max values due to the exchange coupling phenomenon between the soft and hard magnetic phases within the composite. Magnetic energy storage composites are normally composed of rare-earth magnetic materials as well as rare-earth free magnetic materials. Nanotechnology's influence on the enhancement of energy product due to the exchange coupling phenomenon is of great prominence and therefore discussed in this review. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Rare-earth metal oxide doped transparent mesoporous silica plates under non-aqueous condition as a potential UV sensor.

PubMed

Lee, Sang-Joon; Park, Sung Soo; Lee, Sang Hyun; Hong, Sang-Hyun; Ha, Chang-Sik

2013-11-01

Transparent mesoporous silica plates doped with rare-earth metal oxide were prepared using solvent-evaporation method based on the self-organization between structure-directing agent and silicate in a non-aqueous solvent. A triblock copolymer, Pluronic (F127 or P123), was used as the structure-directing agent, while tetraethyl orthosilicate (TEOS) was used as a silica source. The pore diameter and the surface area of the mesoporous silica plate prepared with the optimized conditions were ca 40 A and 600 m2 g(-1), respectively, for both structure-directing agent. Rare-earth metal oxides (Eu, Tb, Tm oxide) in mesochannel were formed via one-step synthetic route based on the preparation method of a silica plate. Optical properties of rare-earth metal oxide-doped mesoporous silica plates were investigated by UV irradiation and photoluminescence (PL) spectroscopy. Under the exitation wavelength of 254 nm, the doped mesoporous silica plates emitted red, green and blue for Eu, Tb and Tm oxides, respectively. Rare-earth metal oxide-doped mesoporous silica plates showed enhanced PL intensity compared to that of the bulk rare-earth metal oxide.

The rapid size- and shape-controlled continuous hydrothermal synthesis of metal sulphide nanomaterials.

PubMed

Dunne, Peter W; Starkey, Chris L; Gimeno-Fabra, Miquel; Lester, Edward H

2014-02-21

Continuous flow hydrothermal synthesis offers a cheap, green and highly scalable route for the preparation of inorganic nanomaterials which has predominantly been applied to metal oxide based materials. In this work we report the first continuous flow hydrothermal synthesis of metal sulphide nanomaterials. A wide range of binary metal sulphides, ZnS, CdS, PbS, CuS, Fe(1-x)S and Bi2S3, have been synthesised. By varying the reaction conditions two different mechanisms may be invoked; a growth dominated route which permits the formation of nanostructured sulphide materials, and a nucleation driven process which produces nanoparticles with temperature dependent size control. This offers a new and industrially viable route to a wide range of metal sulphide nanoparticles with facile size and shape control.

(BRI) Direct and Inverse Design Optimization of Magnetic Alloys with Minimized Use of Rare Earth Elements

DTIC Science & Technology

2016-02-02

Earths ”, MS&T15-Materials Science and Technology 2015 Conference, Columbus, Ohio, October 4-8, 2015. 3. Dulikrvich, G.S., Reddy, S., Orlande, H.R.B...Schwartz, J.and Koch, C.C., “Multi-Objective Design and Optimization of Hard Magnetic Alloys Free of Rare Earths ”, MS&T15-Materials Science and Technology...AFRL-AFOSR-VA-TR-2016-0091 (BRI) Direct and Inverse Design Optimization of Magnetic Alloys with Minimized Use of Rare Earth Elements George

Cobalt and precious metals in sulphides of peridotite xenoliths and inferences concerning their distribution according to geodynamic environment: A case study from the Scottish lithospheric mantle

NASA Astrophysics Data System (ADS)

Hughes, Hannah S. R.; McDonald, Iain; Faithfull, John W.; Upton, Brian G. J.; Loocke, Matthew

2016-01-01

Abundances of precious metals and cobalt in the lithospheric mantle are typically obtained by bulk geochemical analyses of mantle xenoliths. These elements are strongly chalcophile and the mineralogy, texture and trace element composition of sulphide phases in such samples must be considered. In this study we assess the mineralogy, textures and trace element compositions of sulphides in spinel lherzolites from four Scottish lithospheric terranes, which provide an ideal testing ground to examine the variability of sulphides and their precious metal endowments according to terrane age and geodynamic environment. Specifically we test differences in sulphide composition from Archaean-Palaeoproterozoic cratonic sub-continental lithospheric mantle (SCLM) in northern terranes vs. Palaeozoic lithospheric mantle in southern terranes, as divided by the Great Glen Fault (GGF). Cobalt is consistently elevated in sulphides from Palaeozoic terranes (south of the GGF) with Co concentrations > 2.9 wt.% and Co/Ni ratios > 0.048 (chondrite). In contrast, sulphides from Archaean cratonic terranes (north of the GGF) have low abundances of Co (< 3600 ppm) and low Co/Ni ratios (< 0.030). The causes for Co enrichment remain unclear, but we highlight that globally significant Co mineralisation is associated with ophiolites (e.g., Bou Azzer, Morocco and Outokumpu, Finland) or in oceanic peridotite-floored settings at slow-spreading ridges. Thus we suggest an oceanic affinity for the Co enrichment in the southern terranes of Scotland, likely directly related to the subduction of Co-enriched oceanic crust during the Caledonian Orogeny. Further, we identify a distinction between Pt/Pd ratio across the GGF, such that sulphides in the cratonic SCLM have Pt/Pd ≥ chondrite whilst Palaeozoic sulphides have Pt/Pd < chondrite. We observe that Pt-rich sulphides with discrete Pt-minerals (e.g., PtS) are associated with carbonate and phosphates in two xenolith suites north of the GGF. This three-way immiscibility (carbonate-sulphide-phosphate) indicates carbonatitic metasomatism is responsible for Pt-enrichment in this (marginal) cratonic setting. These Co and Pt-enrichments may fundamentally reflect the geodynamic setting of cratonic vs. non-cratonic lithospheric terranes and offer potential tools to facilitate geochemical mapping of the lithospheric mantle.

Spectral engineering of optical fiber through active nanoparticle doping

NASA Astrophysics Data System (ADS)

Lindstrom-James, Tiffany

The spectral engineering of optical fiber is a method of intentional doping of the core region in order to absorb/emit specific wavelengths of light therby providing enhanced performance over current fibers. Efforts here focused on developing an understanding of optically active nanoparticles based on alkaline earth fluorides that could be easily and homogeneously incorporated into the core of a silica based optical fiber preform and result in efficient and tailorable spectral emissions. Doped and undoped calcium, strontium and barium fluoride nanoparticles were successfully synthesized and characterized for their physical, chemical, and optical behavior. Distinct spectroscopic differences as a result of different host materials, varying rare earth doping levels and processing conditions, indicated the ability to influence the spectral behavior of the doped nanoparticle. By using photoluminescence to predict diffusion behavior, the application of a simple one dimensional model for diffusion provided a method for predicting the diffusion coefficient of europium ions in alkaline earth fluorides with order of magnitude accuracy. Modified chemical vapor deposition derived silica preforms were individually solution doped with europium doped alkaline earth fluoride nanoparticles. By using the rare earth doped alkaline earth fluoride nanoparticles as the dopant materials in the core of optical fiber preforms, the resultant optical properties of the glass were significantly influenced by their presence in the core. The incorporation of these rare earth doped alkaline earth fluoride nanoparticles was found to significantly influence the local chemical and structural environment about the rare earth ion, demonstrated homogeneity and uniform distribution of the rare earth dopant and resulted in specifically unique spectral behavior when compared to conventional doping methods. A more detailed structural model of the doped core glass region has been developed based on the spectral behavior of these active fiber preforms. It has been shown that rare earth doping of alkaline earth fluoride nanoparticles provides a material which can be 'tuned' to specific applications through the use of different host materials, processing conditions and doping levels of the rare earth and when used as dopant materials for active optical fibers, provides a means to tailor the optical behavior.

China's Rare Earth Supply Chain: Illegal Production, and Response to new Cerium Demand

NASA Astrophysics Data System (ADS)

Nguyen, Ruby Thuy; Imholte, D. Devin

2016-07-01

As the demand for personal electronic devices, wind turbines, and electric vehicles increases, the world becomes more dependent on rare earth elements. Given the volatile, Chinese-concentrated supply chain, global attempts have been made to diversify supply of these materials. However, the overall effect of supply diversification on the entire supply chain, including increasing low-value rare earth demand, is not fully understood. This paper is the first attempt to shed some light on China's supply chain from both demand and supply perspectives, taking into account different Chinese policies such as mining quotas, separation quotas, export quotas, and resource taxes. We constructed a simulation model using Powersim Studio that analyzes production (both legal and illegal), production costs, Chinese and rest-of-world demand, and market dynamics. We also simulated new demand of an automotive aluminum-cerium alloy in the US market starting from 2018. Results showed that market share of the illegal sector has grown since 2007-2015, ranging between 22% and 25% of China's rare earth supply, translating into 59-65% illegal heavy rare earths and 14-16% illegal light rare earths. There will be a shortage in certain light and heavy rare earths given three production quota scenarios and constant demand growth rate from 2015 to 2030. The new simulated Ce demand would require supply beyond that produced in China. Finally, we illustrate revenue streams for different ore compositions in China in 2015.

China’s rare earth supply chain: Illegal production, and response to new cerium demand

DOE PAGES

Nguyen, Ruby Thuy; Imholte, D. Devin

2016-03-29

As the demand for personal electronic devices, wind turbines, and electric vehicles increases, the world becomes more dependent on rare earth elements. Given the volatile, Chinese-concentrated supply chain, global attempts have been made to diversify supply of these materials. However, the overall effect of supply diversification on the entire supply chain, including increasing low-value rare earth demand, is not fully understood. This paper is the first attempt to shed some light on China’s supply chain from both demand and supply perspectives, taking into account different Chinese policies such as mining quotas, separation quotas, export quotas, and resource taxes. We constructedmore » a simulation model using Powersim Studio that analyzes production (both legal and illegal), production costs, Chinese and rest-of-world demand, and market dynamics. We also simulated new demand of an automotive aluminum-cerium alloy in the U.S. market starting from 2018. Results showed that market share of the illegal sector has grown since 2007 to 2015, ranging between 22% and 25% of China’s rare earth supply, translating into 59–65% illegal heavy rare earths and 14–16% illegal light rare earths. There would be a shortage in certain light and heavy rare earths given three production quota scenarios and constant demand growth rate from 2015 to 2030. The new simulated Ce demand would require supply beyond that produced in China. Lastly, we illustrated revenue streams for different ore compositions in China in 2015.« less

Crystal chemistry and the role of ionic radius in rare earth tetrasilicates: Ba2RE2Si4O12F2 (RE = Er3+-Lu3+) and Ba2RE2Si4O13 (RE = La3+-Ho3+).

PubMed

Fulle, Kyle; Sanjeewa, Liurukara D; McMillen, Colin D; Kolis, Joseph W

2017-10-01

Structural variations across a series of barium rare earth (RE) tetrasilicates are studied. Two different formulas are observed, namely those of a new cyclo-silicate fluoride, BaRE 2 Si 4 O 12 F 2 (RE = Er 3+ -Lu 3+ ) and new compounds in the Ba 2 RE 2 Si 4 O 13 (RE = La 3+ -Ho 3+ ) family, covering the whole range of ionic radii for the rare earth ions. The Ba 2 RE 2 Si 4 O 13 series is further subdivided into two polymorphs, also showing a dependence on rare earth ionic radius (space group P{\\overline 1} for La 3+ -Nd 3+ , and space group C2/c for Sm 3+ -Ho 3+ ). Two of the structure types identified are based on dinuclear rare earth units that differ in their crystal chemistries, particularly with respect to the role of fluorine as a structural director. The broad study of rare earth ions provides greater insight into understanding structural variations within silicate frameworks and the nature of f-block incorporation in oxyanion frameworks. The single crystals are grown from high-temperature (ca 953 K) hydrothermal fluids, demonstrating the versatility of the technique to access new phases containing recalcitrant rare earth oxides, enabling the study of structural trends.

Adsorption of rare earth ions onto the cell walls of wild-type and lipoteichoic acid-defective strains of Bacillus subtilis.

PubMed

Moriwaki, Hiroshi; Koide, Remi; Yoshikawa, Ritsuko; Warabino, Yuya; Yamamoto, Hiroki

2013-04-01

The aim of this study is to investigate the potential of cell walls of wild-type and lipoteichoic acid-defective strains of Bacillus subtilis 168 to adsorb rare earth ions. Freeze-dried cell powders prepared from both strains were used for the evaluation of adsorption ability for the rare earth ions, namely, La(III), Eu(III), and Tm(III). The rare earth ions were efficiently adsorbed onto powders of both wild-type strain (WT powder) and lipoteichoic acid-defective strain (∆LTA powder) at pH 3. The maximum adsorption capacities for Tm(III) by WT and ∆LTA powders were 43 and 37 mg g(-1), respectively. Removal (in percent) of Tm(III), La(III), and Eu(III) from aqueous solution by WT powder was greater than by ∆LTA powder. These results indicate that rare earth ions are adsorbed to functional groups, such as phosphate and carboxyl groups, of lipoteichoic acid. We observed coagulated ∆LTA powder in the removal of rare earth ions (1-20 mg L(-1)) from aqueous solution. In contrast, sedimentation of WT powder did not occur under the same conditions. This unique feature of ∆LTA powder may be caused by the difference of the distribution between lipoteichoic acid and wall teichoic acid. It appears that ∆LTA powder is useful for removal of rare earth ions by adsorption, because aggregation allows for rapid separation of the adsorbent by filtration.

Energy Efficient Materials Manufacturing from Secondary Resources

NASA Astrophysics Data System (ADS)

Apelian, Diran; Mishra, Brajendra

Rare earths metals, including yttrium and scandium, are being increasingly used in clean energy technologies, colored phosphors, lasers and high intensity magnets. There are important defense applications such as fighter jet engines, missile guidance systems and space based satellite and communication systems, based on these metals. The commitment to clean energy technologies by various governments, as well as the projected growth in power and transportation sectors across the globe will certainly escalate the demand for rare earth metals and compounds. This demand implies that to ensure unhindered technological innovation, it is essential to possess secure supply chains for rare earth elements. The United States continues to be one of the largest consumers and importer of rare earths and the trend is expected to continue as the demand increases. In order to ensure secure rare earth supply and attenuate supply-demand imbalances post 2014, it is not only necessary to encourage and support exploration of newer reserves, build a rare earth stockpile, but it is also of utmost importance to look at opportunities to recycle and reuse Rare Earth Elements (REE) from secondary sources, such as post-consumer and manufacturing process wastes. This research describes the technological developments made to convert these valuable resources into functional manufactured materials for lighting industry, automotive and petroleum refining catalysts, and high density permanent magnets. In addition, production of rhenium from advanced aerospace alloys is also discussed from the perspective that it can be recovered for introduction in turbine alloys.

China’s rare earth supply chain: Illegal production, and response to new cerium demand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ruby Thuy; Imholte, D. Devin

As the demand for personal electronic devices, wind turbines, and electric vehicles increases, the world becomes more dependent on rare earth elements. Given the volatile, Chinese-concentrated supply chain, global attempts have been made to diversify supply of these materials. However, the overall effect of supply diversification on the entire supply chain, including increasing low-value rare earth demand, is not fully understood. This paper is the first attempt to shed some light on China’s supply chain from both demand and supply perspectives, taking into account different Chinese policies such as mining quotas, separation quotas, export quotas, and resource taxes. We constructedmore » a simulation model using Powersim Studio that analyzes production (both legal and illegal), production costs, Chinese and rest-of-world demand, and market dynamics. We also simulated new demand of an automotive aluminum-cerium alloy in the U.S. market starting from 2018. Results showed that market share of the illegal sector has grown since 2007 to 2015, ranging between 22% and 25% of China’s rare earth supply, translating into 59–65% illegal heavy rare earths and 14–16% illegal light rare earths. There would be a shortage in certain light and heavy rare earths given three production quota scenarios and constant demand growth rate from 2015 to 2030. The new simulated Ce demand would require supply beyond that produced in China. Lastly, we illustrated revenue streams for different ore compositions in China in 2015.« less

Environmental Benign Process for Production of Molybdenum Metal from Sulphide Based Minerals

NASA Astrophysics Data System (ADS)

Rajput, Priyanka; Janakiram, Vangada; Jayasankar, Kalidoss; Angadi, Shivakumar; Bhoi, Bhagyadhar; Mukherjee, Partha Sarathi

2017-10-01

Molybdenum is a strategic and high temperature refractory metal which is not found in nature in free state, it is predominantly found in earth's crust in the form of MoO3/MoS2. The main disadvantage of the industrial treatment of Mo concentrate is that the process contains many stages and requires very high temperature. Almost in every step many gaseous, liquid, solid chemical substances are formed which require further treatment. To overcome the above drawback, a new alternative one step novel process is developed for the treatment of sulphide and trioxide molybdenum concentrates. This paper presents the results of the investigations on molybdenite dissociation (MoS2) using microwave assisted plasma unit as well as transferred arc thermal plasma torch. It is a single step process for the preparation of pure molybdenum metal from MoS2 by hydrogen reduction in thermal plasma. Process variable such as H2 gas, Ar gas, input current, voltage and time have been examined to prepare molybdenum metal. Molybdenum recovery of the order of 95% was achieved. The XRD results confirm the phases of molybdenum metal and the chemical analysis of the end product indicate the formation of metallic molybdenum (Mo 98%).

Replacing the Rare Earth Intellectual Capital

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gschneidner, Jr., Karl

2011-04-01

The rare earth crisis slowly evolved during a 10 to 15 year period beginning in the mid-1980s, when the Chinese began to export mixed rare earth concentrates. In the early 1990s, they started to move up the supply chain and began to export the individual rare earth oxides and metals. By the late 1990s the Chinese exported higher value products, such as magnets, phosphors, polishing compounds, catalysts; and in the 21st century they supplied finished products including electric motors, computers, batteries, liquid-crystal displays (LCDs), TVs and monitors, mobile phones, iPods and compact fluorescent lamp (CFL) light bulbs. As they movedmore » to higher value products, the Chinese slowly drove the various industrial producers and commercial enterprises in the US, Europe and Japan out of business by manipulating the rare earth commodity prices. Because of this, the technically trained rare earth engineers and scientists who worked in areas from mining to separations, to processing to production, to manufacturing of semifinished and final products, were laid-off and moved to other fields or they retired. However, in the past year the Chinese have changed their philosophy of the 1970s and 1980s of forming a rare earth cartel to control the rare earth markets to one in which they will no longer supply the rest of the world (ROW) with their precious rare earths, but instead will use them internally to meet the growing demand as the Chinese standard of living increases. To this end, they have implemented and occasionally increased export restrictions and added an export tariff on many of the high demand rare earth elements. Now the ROW is quickly trying to start up rare earth mines, e.g. Molycorp Minerals in the US and Lynas Corp. in Australia, to cover this shortfall in the worldwide market, but it will take about five years for the supply to meet the demand, even as other mines in the ROW become productive. Unfortunately, today there is a serious lack of technically trained personnel to bring the entire rare earth industry, from mining to original equipment manufacturers (OEM), up to full speed in the next few years. Accompanying this decline in technical expertise, innovation and new products utilizing rare earth elements has slowed dramatically, and it may take a decade or more to recapture America's leading role in technological advancements of rare earth containing products. Before the disruption of the US rare earth industry, about 25,000 people were employed in all aspects of the industry from mining to OEM. Today, only about 1,500 people are employed in these fields. The ratio of non-technically trained persons to those with college degrees in the sciences or engineering varies from about 8 to 1 to about 4 to 1, depending on the particular area of the industry. Assuming an average of 6 to 1, the number of college degree scientists and engineers has decreased from about 4,000 to 250 employed today. In the magnetic industry the approximate numbers are: 6,000 total with 750 technically trained people in the 1980s to 500 totally employed today of which 75 have degrees. The paucity of scientists and engineers with experience and/or training in the various aspects of production and commercialization of the rare earths is a serious limitation to the ability of the US to satisfy its own needs for materials and technologies (1) to maintain our military strength and posture, (2) to assume leadership in critical energy technologies, and (3) to bring new consumer products to the marketplace. The lack of experts is of even greater national importance than the halting in the 1990s and the recent restart of the mining/benification/separation effort in the US; and thus governmental intervention and support for at least five to 10 years will be required to ameliorate this situation. To respond quickly, training programs should be established in conjunction with a national research center at an educational institution with a long tradition in multiple areas of rare earth and other critical elements research and technology. This center should form close affiliations with other universities, governmental laboratories and non-profit research organizations having complementary strengths. In addition, single investigators or small teams of rare earthers at other universities should be supported by the usual grants from NSF, DOD and DOE. These investigators may or may not be affiliated with the center.« less

Environmental barrier coating

DOEpatents

Pujari, Vimal K.; Vartabedian, Ara; Collins, William T.; Woolley, David; Bateman, Charles

2012-12-18

The present invention relates generally to a multi-layered article suitable for service in severe environments. The article may be formed of a substrate, such as silicon carbide and/or silicon nitride. The substrate may have a first layer of a mixture of a rare earth silicate and Cordierite. The substrate may also have a second layer of a rare earth silicate or a mixture of a rare earth silicate and cordierite.

The impact of rare earth cobalt permanent magnets on electromechanical device design

NASA Technical Reports Server (NTRS)

Fisher, R. L.; Studer, P. A.

1979-01-01

Specific motor designs which employ rare earth cobalt magnets are discussed with special emphasis on their unique properties and magnetic field geometry. In addition to performance improvements and power savings, high reliability devices are attainable. Both the mechanism and systems engineering should be aware of the new performance levels which are currently becoming available as a result of the rare earth cobalt magnets.

The Hall Effect in Hydrided Rare Earth Films

NASA Astrophysics Data System (ADS)

Koon, D. W.; Azofeifa, D. E.; Clark, N.

We describe two new techniques for measuring the Hall effect in capped rare earth films during hydriding. In one, we simultaneously measure resistivity and the Hall coefficient for a rare earth film covered with four different thicknesses of Pd, recovering the charge transport quantities for both materials. In the second technique, we replace Pd with Mn as the covering layer. We will present results from both techniques.

Effects of Rare Earth Metals on Steel Microstructures

PubMed Central

Pan, Fei; Zhang, Jian; Chen, Hao-Long; Su, Yen-Hsun; Kuo, Chia-Liang; Su, Yen-Hao; Chen, Shin-Hau; Lin, Kuan-Ju; Hsieh, Ping-Hung; Hwang, Weng-Sing

2016-01-01

Rare earth metals are used in semiconductors, solar cells and catalysts. This review focuses on the background of oxide metallurgy technologies, the chemical and physical properties of rare earth (RE) metals, the background of oxide metallurgy, the functions of RE metals in steelmaking, and the influences of RE metals on steel microstructures. Future prospects for RE metal applications in steelmaking are also presented. PMID:28773545

Preface to the Special Issue of Optical Materials associated with the ;Photoluminescence in Rare Earths 2016: Photonic Materials and Devices (PRE'16); Workshop

NASA Astrophysics Data System (ADS)

Jacobsohn, Luiz G.; Ballato, John

2017-06-01

Since the inaugural meeting in 2005, the Photoluminescence in Rare Earths: Photonic Materials and Devices (PRE) workshop has grown into a global forum for material scientists, chemists and physicists to discuss and debate the state of the art and future perspectives for photonic materials based on rare earth ions.

Structural control of InP/ZnS core/shell quantum dots enables high-quality white LEDs.

PubMed

Kumar, Baskaran Ganesh; Sadeghi, Sadra; Melikov, Rustamzhon; Aria, Mohammad Mohammadi; Jalali, Houman Bahmani; Ow-Yang, Cleva W; Nizamoglu, Sedat

2018-08-24

Herein, we demonstrate that the structural and optical control of InP-based quantum dots (QDs) can lead to high-performance light-emitting diodes (LEDs). Zinc sulphide (ZnS) shells passivate the InP QD core and increase the quantum yield in green-emitting QDs by 13-fold and red-emitting QDs by 8-fold. The optimised QDs are integrated in the liquid state to eliminate aggregation-induced emission quenching and we fabricated white LEDs with a warm, neutral and cool-white appearance by the down-conversion mechanism. The QD-functionalized white LEDs achieve luminous efficiency (LE) up to 14.7 lm W -1 and colour-rendering index up to 80. The structural and optical control of InP/ZnS core/shell QDs enable 23-fold enhancement in LE of white LEDs compared to ones containing only QDs of InP core.

Zinc Sulphide Overlayer Two-Dimensional Photonic Crystal for Enhanced Extraction of Light from a Micro Cavity Light-Emitting Diode

NASA Astrophysics Data System (ADS)

Mastro, Michael A.; Kim, Chul Soo; Kim, Mijin; Caldwell, Josh; Holm, Ron T.; Vurgaftman, Igor; Kim, Jihyun; Eddy, Charles R., Jr.; Meyer, Jerry R.

2008-10-01

A two-dimensional (2D) ZnS photonic crystal was deposited on the surface of a one-dimensional (1D) III-nitride micro cavity light-emitting diode (LED), to intermix the light extraction features of both structures (1D+2D). The deposition of an ideal micro-cavity optical thickness of ≈λ/2 is impractical for III-nitride LEDs, and in realistic multi-mode devices a large fraction of the light is lost to internal refraction as guided light. Therefore, a 2D photonic crystal on the surface of the LED was used to diffract and thus redirect this guided light out of the semiconductor over several hundred microns. Additionally, the employment of a post-epitaxy ZnS 2D photonic crystal avoided the typical etching into the GaN:Mg contact layer, a procedure which can cause damage to the near surface.

Fabrication of artificially stacked ultrathin ZnS/MgF2 multilayer dielectric optical filters.

PubMed

Kedawat, Garima; Srivastava, Subodh; Jain, Vipin Kumar; Kumar, Pawan; Kataria, Vanjula; Agrawal, Yogyata; Gupta, Bipin Kumar; Vijay, Yogesh K

2013-06-12

We report a design and fabrication strategy for creating an artificially stacked multilayered optical filters using a thermal evaporation technique. We have selectively chosen a zinc sulphide (ZnS) lattice for the high refractive index (n = 2.35) layer and a magnesium fluoride (MgF2) lattice as the low refractive index (n = 1.38) layer. Furthermore, the microstructures of the ZnS/MgF2 multilayer films are also investigated through TEM and HRTEM imaging. The fabricated filters consist of high and low refractive 7 and 13 alternating layers, which exhibit a reflectance of 89.60% and 99%, respectively. The optical microcavity achieved an average transmittance of 85.13% within the visible range. The obtained results suggest that these filters could be an exceptional choice for next-generation antireflection coatings, high-reflection mirrors, and polarized interference filters.

Charge-separated and molecular heterobimetallic rare earth-rare earth and alkaline earth-rare earth aryloxo complexes featuring intramolecular metal-pi-arene interactions.

PubMed

Deacon, Glen B; Junk, Peter C; Moxey, Graeme J; Ruhlandt-Senge, Karin; St Prix, Courtney; Zuniga, Maria F

2009-01-01

Treatment of a rare earth metal (Ln) and a potential divalent rare earth metal (Ln') or an alkaline earth metal (Ae) with 2,6-diphenylphenol (HOdpp) at elevated temperatures (200-250 degrees C) afforded heterobimetallic aryloxo complexes, which were structurally characterised. A charge-separated species [(Ln'/Ae)(2)(Odpp)(3)][Ln(Odpp)(4)] was obtained for a range of metals, demonstrating the similarities between the chemistry of the divalent rare earth metals and the alkaline earth metals. The [(Ln'/Ae)(2)(Odpp)(3)](+) cation in the heterobimetallic structures is unusual in that it consists solely of bridging aryloxide ligands. A molecular heterobimetallic species [AeEu(Odpp)(4)] (Ae = Ca, Sr, Ba) was obtained by treating an alkaline earth metal and Eu metal with HOdpp at elevated temperatures. Similarly, [BaSr(Odpp)(4)] was prepared by treating Ba metal and Sr metal with HOdpp. Treatment of [Ba(2)(Odpp)(4)] with [Mg(Odpp)(2)(thf)(2)] in toluene afforded [Ba(2)(Odpp)(3)][Mg(Odpp)(3)(thf)]. Analogous solution-based syntheses were not possible for [(Ln'/Ae)(2)(Odpp)(3)][Ln(Odpp)(4)] complexes, for which the free-metal route was essential. As a result of the absence of additional donor ligands, the crystal structures of the heterobimetallic complexes feature extensive pi-Ph-metal interactions involving the pendant phenyl groups of the Odpp ligands, thus enabling the large electropositive metal atoms to attain coordination saturation. The charge-separated heterobimetallic species were purified by extraction with toluene/thf mixtures at ambient temperature (Ba-containing compounds) or by extraction with toluene under pressure above the boiling point of the solvent (other products). In donor solvents, heterobimetallic complexes other than those containing barium were found to fragment into homometallic species.

Minimising hydrogen sulphide generation during steam assisted production of heavy oil

PubMed Central

Montgomery, Wren; Sephton, Mark A.; Watson, Jonathan S.; Zeng, Huang; Rees, Andrew C.

2015-01-01

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product. PMID:25670085

Minimising hydrogen sulphide generation during steam assisted production of heavy oil

NASA Astrophysics Data System (ADS)

Montgomery, Wren; Sephton, Mark A.; Watson, Jonathan S.; Zeng, Huang; Rees, Andrew C.

2015-02-01

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product.

Minimising hydrogen sulphide generation during steam assisted production of heavy oil.

PubMed

Montgomery, Wren; Sephton, Mark A; Watson, Jonathan S; Zeng, Huang; Rees, Andrew C

2015-02-11

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product.

Assessment of Potential Health Hazards During Emission of Hydrogen Sulphide from the Mine Exploiting Copper Ore Deposit - Case Study.

PubMed

Kupczewska-Dobecka, Małgorzata; Czerczak, Sławomir; Gromiec, Jan P; Konieczko, Katarzyna

2015-06-01

The aim of this study was to determine hydrogen sulphide concentration emitted from the mine extracting copper ore, to evaluate potential adverse health effects to the population living in four selected villages surrounding the exhaust shaft. Maximum measured concentration of hydrogen sulphide in the emitter is 286 µg/m³. Maximum emission calculated from the results of determinations of concentrations in the emitter is 0.44 kg/h. In selected villages hydrogen sulphide at concentrations exceeding 4 µg/m³ was not detected in any of the 5-hour air samples. In all locations, the estimated maximum 1-hour concentrations of hydrogen sulphide were below 1 µg/m³, and the estimated mean annual concentrations were below 0.53 µg/m³. Any risk to the health of people in the selected area is not expected. As indicated by the available data on the threshold odour, the estimated concentrations of hydrogen sulphide may be sensed by humans. Copyright© by the National Institute of Public Health, Prague 2015.

Sulphide mineralization and wall-rock alteration in ophiolites and modern oceanic spreading centres

USGS Publications Warehouse

Koski, R.A.

1983-01-01

Massive and stockwork Fe-Cu-Zn (Cyprus type) sulphide deposits in the upper parts of ophiolite complexes represent hydrothermal mineralization at ancient accretionary plate boundaries. These deposits are probable metallogenic analogues of the polymetallic sulphide deposits recently discovered along modern oceanic spreading centres. Genetic models for these deposits suggest that mineralization results from large-scale circulation of sea-water through basaltic basement along the tectonically active axis of spreading, a zone of high heat flow. The high geothermal gradient above 1 to 2 km deep magma chambers emplaced below the ridge axis drives the convective circulation cell. Cold oxidizing sea-water penetrating the crust on the ridge flanks becomes heated and evolves into a highly reduced somewhat acidic hydrothermal solvent during interaction with basaltic wall-rock. Depending on the temperature and water/rock ratio, this fluid is capable of leaching and transporting iron, manganese, and base metals; dissolved sea-water sulphate is reduced to sulphide. At the ridge axis, the buoyant hydrothermal fluid rises through permeable wall-rocks, and fluid flow may be focussed along deep-seated fractures related to extensional tectonic processes. Metal sulphides are precipitated along channelways as the ascending fluid undergoes adiabatic expansion and then further cooling during mixing with ambient sub-sea-floor water. Vigorous fluid flow results in venting of reduced fluid at the sea-floor/sea-water interface and deposition of massive sulphide. A comparison of sulphide mineralization and wall-rock alteration in ancient and modern spreading centre environments supports this genetic concept. Massive sulphide deposits in ophiolites generally occur in clusters of closely spaced (< 1-5 km) deposits. Individual deposits are a composite of syngenetic massive sulphide and underlying epigenetic stockwork-vein mineralization. The massive sulphide occurs as concordant tabular, lenticular, or saucer-shaped bodies in pillow lavas and pillow-lava breccia; massive lava flows, hyalcoclastite, tuff, and bedded radolarian chert are less commonly associated rock types. These massive sulphide zones are as much as 700 m long, 200 m wide, and 50 m thick. The pipe-, funnel-, or keel-shaped stockwork zone may extend to a dehpth of 1 km in the sheeted-dike complex. Several deposits in Cyprus are confined to grabens or the hanging wall of premineralization normal faults. Polymetallic massive sulphide deposits and active hydrothermal vents at medium- to fast-rate spreading centres (the East Pacific Rise at lat. 21??N, the Galapagos Spreading Centre at long. 86??W, the Juan de Fuca Ridge at lat. 45??N., and the Southern Trough of Guaymas Basin, Gulf of California) have interdeposit spacings on a scale of tens or hundreds of metres, and are spatially associated with structural ridges or grabens within the narrow (< 5 km) axial valleys of the rift zones. Although the most common substrate for massive sulphide accumulations is stacked sequences of pillow basalt and sheet flows, the sea-floor underlying numerous deposits in Guaymas Basin consists of diatomaceous ooze and terrigenous clastic sediment that is intruded by diabase sills. Mound-like massive sulphide deposits, as much as 30 m wide and 5m high, occur over actively discharging vents on the East Pacific Rise, and many of these deposits serve as the base for narrow chimneys and spires of equal or greater height. Sulphides on the Juan de Fuca Ridge appear to form more widespread blanket deposits in the shallow axial-valley depression. The largest deposit found to date, along the axial ridge of the Galapagos Spreading Centre, has a tabular form and a length of 1000 m, a width of 200 m, and a height of 30 m. The sulphide assemblage in both massive and vein mineralization in Cyprus type deposits is characteristically simple: abundant pyrite or, less commonly, pyrrhotite accompanied by minor marcasite, chalcopyrite

Evaluating United States and world consumption of neodymium, dysprosium, terbium, and praseodymium in final products

NASA Astrophysics Data System (ADS)

Hart, Matthew

This paper develops scenarios of future rare-earth-magnet metal (neodymium, dysprosium, terbium, and praseodymium) consumption in the permanent magnets used in wind turbines and hybrid electric vehicles. The scenarios start with naive base-case scenarios for growth in wind-turbine and hybrid-electric-vehicle sales over the period 2011 to 2020, using historical data for each good. These naive scenarios assume that future growth follows time trends in historical data and does not depend on any exogenous variable. Specifically, growth of each technological market follows historical time trends, and the amount of rare earths used per unit of technology remains fixed. The chosen reference year is 2010. Implied consumptions of the rare earth magnet metals are calculated from these scenarios. Assumptions are made for the material composition of permanent magnets, the market share of permanent-magnet wind turbines and vehicles, and magnet weight per unit of technology. Different scenarios estimate how changes in factors like the material composition of magnets, growth of the economy, and the price of a substitute could affect future consumption. Each scenario presents a different method for reducing rare earth consumption and could be interpreted as potential policy choices. In 2010, the consumption (metric tons, rare-earth-oxide equivalent) of each rare-earth-magnet metal was as follows. Total neodymium consumption in the world for both technologies was 995 tons; dysprosium consumption was 133 tons; terbium consumption was 50 tons; praseodymium consumption was zero tons. The base scenario for wind turbines shows there could be strong, exponential growth in the global wind turbine market. New U.S. sales of hybrid vehicles would decline (in line with the current economic recession) while non-U.S. sales increase through 2020. There would be an overall increase in the total amount of magnetic rare earths consumed in the world. Total consumption of each rare earth in the short-term (2015) and mid-term (2020) scenarios could be between: 1,984 to 6,475 tons (2015) and 3,487 to 13,763 tons (2020) of neodymium; 331 to 864 tons (2015) and 587 to 1,834 tons (2020) of dysprosium; 123 to 325 tons (2015) and 219 to 687 tons (2020) of terbium; finally, zero to 871 tons (2015) and zero to 1,493 tons (2020) of praseodymium. Hybrid vehicle sales in non-U.S. countries could account for a large portion of magnetic rare earth consumption. Wind turbine and related rare earth consumption growth will also be driven by non-U.S. countries, especially developing nations like China. Despite wind turbines using bigger magnets, the sheer volume of hybrids sold and non-U.S. consumers could account for most future consumption of permanent magnets and their rare earths.

The influence of reaction time on hydrogen sulphide removal from air by means of Fe(III)-EDTA/Fiban catalysts

NASA Astrophysics Data System (ADS)

Wasag, H.; Cel, W.; Chomczynska, M.; Kujawska, J.

2018-05-01

The paper deals with a new method of hydrogen sulphide removal from air by its filtration and selective catalytic oxidation with the use of fibrous carriers of Fe(III)-EDTA complex. The basis of these filtering materials includes fibrous ion exchangers with the complex immobilized on their functional groups. It has been established that the degree of catalytic hydrogen sulphide decomposition depends on the reaction time. Thus, the required degree of hydrogen sulphide removal from air could be easily controlled by applying appropriate thickness of the filtering layer under a given filtering velocity. It allows applying very thin filtering layers of the Fe(III)-EDTA/Fiban AK-22 or Fiban A-6 catalysts. The obtained results of the research confirm the applicability of these materials for deep air purification from hydrogen sulphide.

Synthesis and characterization of rare-earth-doped calcium tungstate nanocrystals

NASA Astrophysics Data System (ADS)

Suneeta, P.; Rajesh, Ch.; Ramana, M. V.

2018-02-01

In this paper, we report synthesis and characterization of rare-earth-ion-doped calcium tungstate (CaWO4) nanocrystals (NCs). Rare-earth ions, such as gadolinium (Gd), neodymium (Nd), praseodymium (Pr), samarium (Sm) and holmium (Ho), were successfully doped in the CaWO4 NCs by changing the synthesis conditions. The adopted synthesis route was found to be fast and eco-friendly. Structural characterizations, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and compositional analysis, were performed using energy dispersive analysis of X-rays (EDAX) on as-synthesized NCs. The results indicate the size of the NCs ranging between 47 to 68nm and incorporation of rare-earth ions in CaWO4 NCs.

Method for treating rare earth-transition metal scrap

DOEpatents

Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.; Jones, Lawrence L.

1992-12-29

Rare earth-transition metal (e.g., iron) scrap (e.g., Nd-Fe-B scrap) is flux (slag) remelted to reduce tramp non-metallic impurities, such as oxygen and nitrogen, and metallic impurities, such as Li, Na, Al, etc., picked up by the scrap from previous fabrication operations. The tramp impurities are reduced to concentrations acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. The scrap is electroslag or inductoslag melted using a prefused, rare earth fluoride-bearing flux of CaF.sub.2, CaCl.sub.2 or mixtures thereof or the slag resulting from practice of the thermite reduction process to make a rare earth-iron alloy.

Method for treating rare earth-transition metal scrap

DOEpatents

Schmidt, F.A.; Peterson, D.T.; Wheelock, J.T.; Jones, L.L.

1992-12-29

Rare earth-transition metal (e.g., iron) scrap (e.g., Nd-Fe-B scrap) is flux (slag) remelted to reduce tramp non-metallic impurities, such as oxygen and nitrogen, and metallic impurities, such as Li, Na, Al, etc., picked up by the scrap from previous fabrication operations. The tramp impurities are reduced to concentrations acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. The scrap is electroslag or inductoslag melted using a rare earth fluoride-bearing flux of CaF[sub 2], CaCl[sub 2] or mixtures thereof or the slag resulting from practice of the thermite reduction process to make a rare earth-iron alloy. 3 figs.

Anhydrite pseudomorphs and the origin of stratiform Cu-Co ores in the Katangan Copperbelt (Democratic Republic of Congo)

NASA Astrophysics Data System (ADS)

Muchez, Ph.; Vanderhaeghen, P.; El Desouky, H.; Schneider, J.; Boyce, A.; Dewaele, S.; Cailteux, J.

2008-07-01

The stratiform Cu-Co ore mineralisation in the Katangan Copperbelt consists of dispersed sulphides and sulphides in nodules and lenses, which are often pseudomorphs after evaporites. Two types of pseudomorphs can be distinguished in the nodules and lenses. In type 1 examples, dolomite precipitated first and was subsequently replaced by Cu-Co sulphides and authigenic quartz, whereas in type 2 examples, authigenic quartz and Cu-Co sulphides precipitated prior to dolomite and are coarse-grained. The sulphur isotopic composition of the copper-cobalt sulphides in the type 1 pseudomorphs is between -10.3 and 3.1‰ relative to the Vienna Canyon Diablo Troilite, indicating that the sulphide component was derived from bacterial sulphate reduction (BSR). The generation of {text{HCO}}_3^ - during this process caused the precipitation and replacement of anhydrite by dolomite. A second product of BSR is the generation of H2S, resulting in the precipitation of Cu-Co sulphides from the mineralising fluids. Initial sulphide precipitation occurred along the rim of the pseudomorphs and continued towards the core. Precipitation of authigenic quartz was most likely induced by a pH decrease during sulphide precipitation. Fluid inclusion data from quartz indicate the presence of a high-salinity (8-18 eq. wt.% NaCl) fluid, possibly derived from evaporated seawater which migrated through the deep subsurface. 87Sr/86Sr ratios of dolomite in type 1 nodules range between 0.71012 and 0.73576, significantly more radiogenic than the strontium isotopic composition of Neoproterozoic marine carbonates (87Sr/86Sr = 0.7056-0.7087). This suggests intense interaction with siliciclastic sedimentary rocks and/or the granitic basement. The low carbon isotopic composition of the dolomite in the pseudomorphs (-7.02 and -9.93‰ relative to the Vienna Pee Dee Belemnite, V-PDB) compared to the host rock dolomite (-4.90 and +1.31‰ V-PDB) resulted from the oxidation of organic matter during BSR.

Ultrasound-assisted leaching of rare earths from the weathered crust elution-deposited ore using magnesium sulfate without ammonia-nitrogen pollution.

PubMed

Yin, Shaohua; Pei, Jiannan; Jiang, Feng; Li, Shiwei; Peng, Jinhui; Zhang, Libo; Ju, Shaohua; Srinivasakannan, Chandrasekar

2018-03-01

The in situ leaching process of China's unique ion-adsorption rare earth ores has caused severe environmental damages due to the use of (NH 4 ) 2 SO 4 solution. This study reports that magnesium sulfate (MgSO 4 ) as a leaching agent would replace (NH 4 ) 2 SO 4 by ultrasonically assisted leaching to deal with the ammonia-nitrogen pollution problem and enhance leaching process. At leaching conditions of 3wt% MgSO 4 concentration, 3:1L/S ratio and 30min, the total rare earth leaching efficiency reaches 75.5%. Ultrasound-assisted leaching experiments show that the leaching efficiency of rare earths is substantially increased by introducing ultrasound, and nearly completely leached out after two stage leaching process. Thus, ultrasonic-assisted leaching process with MgSO 4 is not only effective but also environmentally friendly, and beneficial to leach rare earths at laboratory scale. Copyright © 2017 Elsevier B.V. All rights reserved.

Contributed Review: A review of the investigation of rare-earth dopant profiles in optical fibers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sidiroglou, F.; Baxter, G.; Roberts, A.

Rare-earth doped optical fibers have captivated the interest of many researchers around the world across the past three decades. The growth of this research field has been stimulated primarily through their application in optical communications as fiber lasers and amplifiers, although rare-earth doped optical fiber based devices are now finding important uses in many other scientific and industrial areas (for example, medicine, sensing, the military, and material processing). Such wide commercial interest has provided a strong incentive for innovative fiber designs, alternative glass compositions, and novel fabrication processes. A prerequisite for the ongoing progress of this research field is developingmore » the capacity to provide high resolution information about the rare-earth dopant distribution profiles within the optical fibers. This paper constitutes a comprehensive review of the imaging techniques that have been utilized in the analysis of the distribution of the rare-earth ion erbium within the core of optical fibers.« less

Equilibrium distribution of rare earth elements between molten KCl-LiCl eutectic salt and liquid cadmium

NASA Astrophysics Data System (ADS)

Sakata, Masahiro; Kurata, Masaki; Hijikata, Takatoshi; Inoue, Tadashi

1991-11-01

Distribution experiments for several rare earth elements (La, Ce, Pr, Nd and Y) between molten KCl-LiCl eutectic salt and liquid Cd were carried out at 450, 500 and 600°C. The material balance of rare earth elements after reaching the equilibrium and their distribution and chemical states in a Cd sample frozen after the experiment were examined. The results suggested the formation of solid intermetallic compounds at the lower concentrations of rare earth metals dissolved in liquid Cd than those solubilities measured in the binary alloy system. The distribution coefficients of rare earth elements between two phases (mole fraction in the Cd phase divided by mole fraction in the salt phase) were determined at each temperature. These distribution coefficients were explained satisfactorily by using the activity coefficients of chlorides and metals in salt and Cd. Both the activity coefficients of metal and chloride caused a much smaller distribution coefficient of Y relative to those of other elements.

Catalytic Graphitization of Coal-Based Carbon Materials with Light Rare Earth Elements.

PubMed

Wang, Rongyan; Lu, Guimin; Qiao, Wenming; Yu, Jianguo

2016-08-30

The catalytic graphitization mechanism of coal-based carbon materials with light rare earth elements was investigated using X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, selected-area electron diffraction, and high-resolution transmission electron microscopy. The interface between light rare earth elements and carbon materials was carefully observed, and two routes of rare earth elements catalyzing the carbon materials were found: dissolution-precipitation and carbide formation-decomposition. These two simultaneous processes certainly accelerate the catalytic graphitization of carbon materials, and light rare earth elements exert significant influence on the microstructure and thermal conductivity of graphite. Moreover, by virtue of praseodymium (Pr), it was found that a highly crystallographic orientation of graphite was induced and formed, which was reasonably attributed to the similar arrangements of the planes perpendicular to (001) in both graphite and Pr crystals. The interface between Pr and carbon was found to be an important factor for the orientation of graphite structure.

Separation of the rare-earth fission product poisons from spent nuclear fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christian, Jerry D.; Sterbentz, James W.

A method for the separation of the rare-earth fission product poisons comprising providing a spent nuclear fuel. The spent nuclear fuel comprises UO.sub.2 and rare-earth oxides, preferably Sm, Gd, Nd, Eu oxides, with other elements depending on the fuel composition. Preferably, the provided nuclear fuel is a powder, preferably formed by crushing the nuclear fuel or using one or more oxidation-reduction cycles. A compound comprising Th or Zr, preferably metal, is provided. The provided nuclear fuel is mixed with the Th or Zr, thereby creating a mixture. The mixture is then heated to a temperature sufficient to reduce the UO.sub.2more » in the nuclear fuel, preferably to at least to 850.degree. C. for Th and up to 600.degree. C. for Zr. Rare-earth metals are then extracted to form the heated mixture thereby producing a treated nuclear fuel. The treated nuclear fuel comprises the provided nuclear fuel having a significant reduction in rare-earths.« less

Reversing Conventional Reactivity of Mixed Oxo/Alkyl Rare-Earth Complexes: Non-Redox Oxygen Atom Transfer.

PubMed

Hong, Jianquan; Tian, Haiwen; Zhang, Lixin; Zhou, Xigeng; Del Rosal, Iker; Weng, Linhong; Maron, Laurent

2018-01-22

The preferential substitution of oxo ligands over alkyl ones of rare-earth complexes is commonly considered as "impossible" due to the high oxophilicity of metal centers. Now, it has been shown that simply assembling mixed methyl/oxo rare-earth complexes to a rigid trinuclear cluster framework cannot only enhance the activity of the Ln-oxo bond, but also protect the highly reactive Ln-alkyl bond, thus providing a previously unrecognized opportunity to selectively manipulate the oxo ligand in the presence of numerous reactive functionalities. Such trimetallic cluster has proved to be a suitable platform for developing the unprecedented non-redox rare-earth-mediated oxygen atom transfer from ketones to CS 2 and PhNCS. Controlled experiments and computational studies shed light on the driving force for these reactions, emphasizing the importance of the sterical accessibility and multimetallic effect of the cluster framework in promoting reversal of reactivity of rare-earth oxo complexes. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Syntheses of new rare earth complexes with carboxymethylated polysaccharides and evaluation of their in vitro antifungal activities.

PubMed

Sun, Xiaobo; Jin, Xiaozhe; Pan, Wei; Wang, Jinping

2014-11-26

In the present paper, La, Eu and Yb were selected to represent light, middle and heavy rare earths to form complexes with polysaccharides through chelating coordination of carboxyl groups, which were added into polysaccharide chains by means of carboxymethylation. Their antifungal activities against plant pathogenic fungi were evaluated using growth rate method. These rare earth complexes exhibited various antifungal activities against the tested fungi, depending on rare earth elements, polysaccharide types and fungal species. Among these three metal elements (i.e. La, Eu and Yb), Yb formed the complexes with the most effective antifungal properties. Furthermore, the results showed that ligands of carboxymethylated polysaccharides played a key role in promoting cytotoxicity of the rare earth complexes. Carboxymethylated Ganoderma applanatum polysaccharide (CGAP) was found to be the most effective ligand to form complexes with antifungal activities, followed by carboxymethylated lentinan (CLNT) and carboxymethylated Momordica charantia polysaccharide (CMCP). Copyright © 2014 Elsevier Ltd. All rights reserved.

Micromagnetics of rare-earth efficient permanent magnets

NASA Astrophysics Data System (ADS)

Fischbacher, Johann; Kovacs, Alexander; Gusenbauer, Markus; Oezelt, Harald; Exl, Lukas; Bance, Simon; Schrefl, Thomas

2018-05-01

The development of permanent magnets containing less or no rare-earth elements is linked to profound knowledge of the coercivity mechanism. Prerequisites for a promising permanent magnet material are a high spontaneous magnetization and a sufficiently high magnetic anisotropy. In addition to the intrinsic magnetic properties the microstructure of the magnet plays a significant role in establishing coercivity. The influence of the microstructure on coercivity, remanence, and energy density product can be understood by using micromagnetic simulations. With advances in computer hardware and numerical methods, hysteresis curves of magnets can be computed quickly so that the simulations can readily provide guidance for the development of permanent magnets. The potential of rare-earth reduced and rare-earth free permanent magnets is investigated using micromagnetic simulations. The results show excellent hard magnetic properties can be achieved in grain boundary engineered NdFeB, rare-earth magnets with a ThMn12 structure, Co-based nano-wires, and L10-FeNi provided that the magnet’s microstructure is optimized.

Dual Functionalization of White Phosphorus: Formation, Characterization, and Reactivity of Rare-Earth-Metal Cyclo-P3 Complexes.

PubMed

Du, Shanshan; Yin, Jianhao; Chi, Yue; Xu, Ling; Zhang, Wen-Xiong

2017-12-11

The [3+1] fragmentation reaction of rare-earth metallacyclopentadienes 1 a-c with 0.5 equivalents of P 4 affords a series of rare-earth metal cyclo-P 3 complexes 2 a-c and a phospholyl anion 3. 2 a-c demonstrate an unusual η 3 coordination mode with one P-P bond featuring partial π-bonding character. 2 a-c are the first cyclo-P 3 complexes of rare-earth metals, and also the first organo-substituted polyphosphides in the category of Group 3 and f-block elements. Rare-earth metallacyclopentadienes play a dual role in the combination of aromatization and Diels-Alder reaction. Compounds 2 a-c can coordinate to one or two [W(CO) 5 ] units, yielding 4 a-c or 5 c, respectively. Furthermore, oxidation of 2 a with p-benzoquinone produces its corresponding phospholyllithium and regenerated P 4 . © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nanoparticulate-catalyzed oxygen transfer processes

DOEpatents

Hunt, Andrew T [Atlanta, GA; Breitkopf, Richard C [Dunwoody, GA

2009-12-01

Nanoparticulates of oxygen transfer materials that are oxides of rare earth metals, combinations of rare earth metals, and combinations of transition metals and rare earth metals are used as catalysts in a variety of processes. Unexpectedly large thermal efficiencies are achieved relative to micron sized particulates. Processes that use these catalysts are exemplified in a multistage reactor. The exemplified reactor cracks C6 to C20 hydrocarbons, desulfurizes the hydrocarbon stream and reforms the hydrocarbons in the stream to produce hydrogen. In a first reactor stage the steam and hydrocarbon are passed through particulate mixed rare earth metal oxide to crack larger hydrocarbon molecules. In a second stage, the steam and hydrocarbon are passed through particulate material that desulfurizes the hydrocarbon. In a third stage, the hydrocarbon and steam are passed through a heated, mixed transition metal/rare earth metal oxide to reform the lower hydrocarbons and thereby produce hydrogen. Stages can be alone or combined. Parallel reactors can provide continuous reactant flow. Each of the processes can be carried out individually.

Rare earths: Market disruption, innovation, and global supply chains

USGS Publications Warehouse

Eggert, Roderick; Wadia, Cyrus; Anderson, Corby; Bauer, Diana; Fields, Fletcher; Meinert, Lawrence D.; Taylor, Patrick

2016-01-01

Rare earths, sometimes called the vitamins of modern materials, captured public attention when their prices increased more than ten-fold in 2010 and 2011. As prices fell between 2011 and 2016, rare earths receded from public view—but less visibly they became a major focus of innovative activity in companies, government laboratories and universities. Geoscientists worked to better understand the resource base and improve our knowledge about mineral deposits that will be mines in the future. Process engineers carried out research that is making primary production and recycling more efficient. Materials scientists and engineers searched for substitutes that will require fewer or no rare earths while providing properties comparable or superior to those of existing materials. As a result, even though global supply chains are not significantly different now than they were before the market disruption, the innovative activity motivated by the disruption likely will have far-reaching, if unpredictable, consequences for supply chains of rare earths in the future.

Effect of rare-earth ion size on local electron structure in RBa 2Cu 3O 7- δ (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors: A positron study

NASA Astrophysics Data System (ADS)

Chen, Zhenping; Zhang, Jincang; Su, Yuling; Xue, Yuncai; Cao, Shixun

2006-02-01

The effects of rare-earth ionic size on the local electron structure, lattice parameters and superconductivity have been investigated by positron annihilation technique (PAT) and related experiments for RBa 2Cu 3O 7- δ (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors. The local electron density ne is evaluated as a function of the rare-earth radius. The results show that both the bulk-lifetime τB and the defect lifetime τ2 increase with increasing rare-earth ionic radius, while the local electron density ne decrease with increasing rare-earth ionic radius. These results prove that the changes of ne, the degree of orthorhombic distortion and the coupling between the Cu-O chains and the CuO 2 planes all have an effect on the superconductivity of RBa 2Cu 3O 7- δ systems.

The Rare Earth Magnet Industry and Rare Earth Price in China

NASA Astrophysics Data System (ADS)

Ding, Kaihong

2014-07-01

In the past four years, the price of rare earth metal fluctuates sharply for many reasons. Currently, it has become more stable and more reasonable. This presentation is focused on the effect about the rare earth metal price. Some motor manufacturers have shifted from rare earth permanent magnet to ferrite magnet. Many motor manufacturers changed the design for the motor cooling system to make the motor function at a lower temperature. Thus the consumption of Dy can be markedly reduced. As for manufacturer of NdFeB magnet, we are also trying to optimize our process to reduce to dependence of HREE such as Dy and Tb. HS process have been introduced to solve the problem. With more and more people focusing and engaging on the REE industry, the price of REE will be more transparent without too many fluctuations. China is considering the problems of balancing the environment, energy sources, and labor sources. The application field about NdFeB such as wind turbine generator, HEV/EV, FA /OA is flourishing.

Hydrogen sulphide protects against NSAID-enteropathy through modulation of bile and the microbiota

PubMed Central

Blackler, Rory W; Motta, Jean-Paul; Manko, Anna; Workentine, Matthew; Bercik, Premysl; Surette, Michael G; Wallace, John L

2015-01-01

Background and Purpose Hydrogen sulphide is an important mediator of gastrointestinal mucosal defence. The use of non-steroidal anti-inflammatory drugs (NSAIDs) is significantly limited by their toxicity in the gastrointestinal tract. Particularly concerning is the lack of effective preventative or curative treatments for NSAID-induced intestinal damage and bleeding. We evaluated the ability of a hydrogen sulphide donor to protect against NSAID-induced enteropathy. Experimental Approach Intestinal ulceration and bleeding were induced in Wistar rats by oral administration of naproxen. The effects of suppression of endogenous hydrogen sulphide synthesis or administration of a hydrogen sulphide donor (diallyl disulphide) on naproxen-induced enteropathy was examined. Effects of diallyl disulphide on small intestinal inflammation and intestinal microbiota were also assessed. Bile collected after in vivo naproxen and diallyl disulphide administration was evaluated for cytotoxicity in vitro using cultured intestinal epithelial cells. Key Results Suppression of endogenous hydrogen sulphide synthesis by β-cyano-L-alanine exacerbated naproxen-induced enteropathy. Diallyl disulphide co-administration dose-dependently reduced the severity of naproxen-induced small intestinal damage, inflammation and bleeding. Diallyl disulphide administration attenuated naproxen-induced increases in the cytotoxicity of bile on cultured enterocytes, and prevented or reversed naproxen-induced changes in the intestinal microbiota. Conclusions and Implications Hydrogen sulphide protects against NSAID-enteropathy in rats, in part reducing the cytotoxicity of bile and preventing NSAID-induced dysbiosis. PMID:25297699

Molten metal containment vessel with rare earth oxysulfide protective coating thereon and method of making same

DOEpatents

Krikorian, Oscar H.; Curtis, Paul G.

1992-01-01

An improved molten metal containment vessel is disclosed in which wetting of the vessel's inner wall surfaces by molten metal is inhibited by coating at least the inner surfaces of the containment vessel with one or more rare earth oxysulfide or rare earth sulfide compounds to inhibit wetting and or adherence by the molten metal to the surfaces of the containment vessel.

Optical Properties of Nd Doped Rare Earth Vanadates (Preprint)

DTIC Science & Technology

2010-07-01

Rare earth orthovanadates are being used as substitute for traditional solid state laser hosts such as yttrium aluminium garnet (YAG). While the most...common of these is yttrium orthovanadate, other rare earth vanadates such as lutetium vanadate and gadolinium vanadate are being used for their... gadolinium vanadate are being used for their special properties in certain applications. We report new measurements of the refractive indices and thermo

Rare earth element mineralogy, geochemistry, and preliminary resource assessment of the Khanneshin carbonatite complex, Helmand Province, Afghanistan

USGS Publications Warehouse

Tucker, Robert D.; Belkin, Harvey E.; Schulz, Klaus J.; Peters, Stephen G.; Buttleman, Kim P.

2011-01-01

There is increased concern about the future availability of rare earth elements (REE) because of China's dominance as the supplier of more than 95 percent of world REE output, their decision to restrict exports of rare earth products, and the rapid increase in world-wide consumption of rare earth product. As a result, countries such as the United States, Japan, and member nations of the European Union face a future of tight supplies and high prices for rare earth products unless other sources of REE are found and developed (Long and others, 2010; U.S. Geological Survey, 2011, p. 128-129, 184-185). We report and describe a significant new deposit of light rare earth elements (LREE), estimated at 1 Mt, within the Khanneshin carbonatite complex of south Afghanistan. The potential resource is located in a remote and rugged part of the igneous complex in a region previously identified by Soviet geologists in the 1970s. This report reviews the geologic setting of LREE deposit, presents new geochemical data documenting the grade of LREE mineralization, briefly describes the mineralogy and mineralogical associations of the deposit, and presents a preliminary estimate of LREE resources based on our current understanding of the geology.

Computational search for rare-earth free hard-magnetic materials

NASA Astrophysics Data System (ADS)

Flores Livas, José A.; Sharma, Sangeeta; Dewhurst, John Kay; Gross, Eberhard; MagMat Team

2015-03-01

It is difficult to over state the importance of hard magnets for human life in modern times; they enter every walk of our life from medical equipments (NMR) to transport (trains, planes, cars, etc) to electronic appliances (for house hold use to computers). All the known hard magnets in use today contain rare-earth elements, extraction of which is expensive and environmentally harmful. Rare-earths are also instrumental in tipping the balance of world economy as most of them are mined in limited specific parts of the world. Hence it would be ideal to have similar characteristics as a hard magnet but without or at least with reduced amount of rare-earths. This is the main goal of our work: search for rare-earth-free magnets. To do so we employ a combination of density functional theory and crystal prediction methods. The quantities which define a hard magnet are magnetic anisotropy energy (MAE) and saturation magnetization (Ms), which are the quantities we maximize in search for an ideal magnet. In my talk I will present details of the computation search algorithm together with some potential newly discovered rare-earth free hard magnet. J.A.F.L. acknowledge financial support from EU's 7th Framework Marie-Curie scholarship program within the ``ExMaMa'' Project (329386).

Deep-sea mud in the Pacific Ocean as a potential resource for rare-earth elements

NASA Astrophysics Data System (ADS)

Kato, Yasuhiro; Fujinaga, Koichiro; Nakamura, Kentaro; Takaya, Yutaro; Kitamura, Kenichi; Ohta, Junichiro; Toda, Ryuichi; Nakashima, Takuya; Iwamori, Hikaru

2011-08-01

World demand for rare-earth elements and the metal yttrium--which are crucial for novel electronic equipment and green-energy technologies--is increasing rapidly. Several types of seafloor sediment harbour high concentrations of these elements. However, seafloor sediments have not been regarded as a rare-earth element and yttrium resource, because data on the spatial distribution of these deposits are insufficient. Here, we report measurements of the elemental composition of over 2,000 seafloor sediments, sampled at depth intervals of around one metre, at 78 sites that cover a large part of the Pacific Ocean. We show that deep-sea mud contains high concentrations of rare-earth elements and yttrium at numerous sites throughout the eastern South and central North Pacific. We estimate that an area of just one square kilometre, surrounding one of the sampling sites, could provide one-fifth of the current annual world consumption of these elements. Uptake of rare-earth elements and yttrium by mineral phases such as hydrothermal iron-oxyhydroxides and phillipsite seems to be responsible for their high concentration. We show that rare-earth elements and yttrium are readily recovered from the mud by simple acid leaching, and suggest that deep-sea mud constitutes a highly promising huge resource for these elements.

The Link Between Rare-Earth Peak Formation and the Astrophysical Site of the R Process

DOE PAGES

Mumpower, Matthew R.; McLaughlin, Gail C.; Surman, Rebecca; ...

2016-12-20

The primary astrophysical source of the rare-earth elements is the rapid neutron capture process (r process). The rare-earth peak that is seen in the solar r-process residuals has been proposed to originate as a pile-up of nuclei during the end of the r process. Here, we introduce a new method utilizing Monte Carlo studies of nuclear masses in the rare-earth region, that includes self-consistently adjusting β-decay rates and neutron capture rates, to find the mass surfaces necessary for the formation of the rare-earth peak. We demonstrate our method with two types of astrophysical scenario, one corresponding to conditions typical ofmore » hot winds from core-collapse supernovae and stellar-mass accretion disks, and one corresponding to conditions typical of the ejection of the material from the tidal tails of neutron star mergers. In each type of astrophysical condition, this method successfully locates a region of enhanced stability in the mass surface that is responsible for the rare-earth peak. Finally, for each scenario, we find that the change in the mass surface has qualitatively different features, thus future measurements can shed light on the type of environment in which the r process occurred.« less

Rare Earth Extraction from NdFeB Magnet Using a Closed-Loop Acid Process.

PubMed

Kitagawa, Jiro; Uemura, Ryohei

2017-08-14

There is considerable interest in extraction of rare earth elements from NdFeB magnets to enable recycling of these elements. In practical extraction methods using wet processes, the acid waste solution discharge is a problem that must be resolved to reduce the environmental impact of the process. Here, we present an encouraging demonstration of rare earth element extraction from a NdFeB magnet using a closed-loop hydrochloric acid (HCl)-based process. The extraction method is based on corrosion of the magnet in a pretreatment stage and a subsequent ionic liquid technique for Fe extraction from the HCl solution. The rare earth elements are then precipitated using oxalic acid. Triple extraction has been conducted and the recovery ratio of the rare earth elements from the solution is approximately 50% for each extraction process, as compared to almost 100% recovery when using a one-shot extraction process without the ionic liquid but with sufficient oxalic acid. Despite its reduced extraction efficiency, the proposed method with its small number of procedures at almost room temperature is still highly advantageous in terms of both cost and environmental friendliness. This study represents an initial step towards realization of a closed-loop acid process for recycling of rare earth elements.

Improvement Photocatalytic Activity of P25 by Modification with a Rare Earth-Free Upconversion Nanocrystal.

PubMed

Yin, Dongguang; Liu, Yumin; Zhao, Feifei; Zhang, Xinyu; Zhang, Tingting; Wu, Chenglong; Chang, Na; Chen, Zhiwen

2018-05-01

It has been reported that coupling TiO2 with rare earth upconversion nanocrystals (UCNCs) is an efficient strategy to significantly improve photocatalytic activity of TiO2. However, the rare earth materials are scarcity and cost, and the synthesis process of UCNCs using the rare earth materials is complicated. In the present study, we have designed a new approach using a rare earth-free upconversion nanocrystal (REF-UCNCs) as upconversion luminescent material to replace the rare earth UCNCs. A novel nanocomposite photocatalyst of REF-UCNCs@P25: Mo/GN was developed for the first time. Based on the designed structure, the REF-UCNCs, Mo-doping, and GN (graphene) have a synergistic effect that can improve catalytic activity of P25 significantly. The results of photocatalytic experiments using RhB as a model pollutant under simulated solar light irradiation show that the photocatalytic efficiency of the as-prepared catalyst is 3-folds higher than that of benchmark substance P25. This work provides a new strategy for efficiently improving catalytic activity of semiconductor photocatalysts by coupling with REF-UCNCs. This approach is facile and low-cost which can be widely applied for modification of semiconductor photocatalysts and facilitates their applications in environmental protection issues using solar light.

The Link Between Rare-Earth Peak Formation and the Astrophysical Site of the R Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mumpower, Matthew R.; McLaughlin, Gail C.; Surman, Rebecca

The primary astrophysical source of the rare-earth elements is the rapid neutron capture process (r process). The rare-earth peak that is seen in the solar r-process residuals has been proposed to originate as a pile-up of nuclei during the end of the r process. Here, we introduce a new method utilizing Monte Carlo studies of nuclear masses in the rare-earth region, that includes self-consistently adjusting β-decay rates and neutron capture rates, to find the mass surfaces necessary for the formation of the rare-earth peak. We demonstrate our method with two types of astrophysical scenario, one corresponding to conditions typical ofmore » hot winds from core-collapse supernovae and stellar-mass accretion disks, and one corresponding to conditions typical of the ejection of the material from the tidal tails of neutron star mergers. In each type of astrophysical condition, this method successfully locates a region of enhanced stability in the mass surface that is responsible for the rare-earth peak. Finally, for each scenario, we find that the change in the mass surface has qualitatively different features, thus future measurements can shed light on the type of environment in which the r process occurred.« less

THE LINK BETWEEN RARE-EARTH PEAK FORMATION AND THE ASTROPHYSICAL SITE OF THE R PROCESS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mumpower, Matthew R.; McLaughlin, Gail C.; Surman, Rebecca

The primary astrophysical source of the rare-earth elements is the rapid neutron capture process ( r process). The rare-earth peak that is seen in the solar r -process residuals has been proposed to originate as a pile-up of nuclei during the end of the r process. We introduce a new method utilizing Monte Carlo studies of nuclear masses in the rare-earth region, that includes self-consistently adjusting β -decay rates and neutron capture rates, to find the mass surfaces necessary for the formation of the rare-earth peak. We demonstrate our method with two types of astrophysical scenario, one corresponding to conditionsmore » typical of hot winds from core-collapse supernovae and stellar-mass accretion disks, and one corresponding to conditions typical of the ejection of the material from the tidal tails of neutron star mergers. In each type of astrophysical condition, this method successfully locates a region of enhanced stability in the mass surface that is responsible for the rare-earth peak. For each scenario, we find that the change in the mass surface has qualitatively different features, thus future measurements can shed light on the type of environment in which the r process occurred.« less

[Analysis of X-Ray Fluorescence Spectroscopy and Plasma Mass Spectrometry of Pangxidong Composite Granitoid Pluton and Its Implications for Magmatic Differentiation].

PubMed

Zeng, Chang-yu; Ding, Ru-xin; Li, Hong-zhong; Zhou, Yong-zhang; Niu, Jia; Zhang, Jie-tang

2015-11-01

Pangxidong composite granitoid pluton located in the southwestern margin of Yunkai massif. The metamorphic grade of this pluton increases from outside to inside, that is, banded-augen granitic gneisses, gneissoid granites and granites distribute in order from edge to core. X-Ray Fluorescence Spectroscopy and Plasma Mass Spectrometry are conducted to study the geochemical characteristics of the three types of rocks. The result shows that all the three types of rocks are peraluminous rocks and their contents of main elements and rare earth elements change gradually. From granitic gneisses to granites, the contents of Al₂O₃, CaO, MgO, TiO₂, total rare earth elements and light rare earth elements increase, but the contents of SiO₂ and heavy rare earth elements decrease. It is suggested that the phylogenetic relationship exists between granitic gneisses, gneissoid granites and granites during the multi-stage tectonic evolution process. Furthermore, the remelting of metamorphosed supracrustal rocks in Yunkai massif is probably an important cause of granitoid rocks forming. The evolutionary mechanism is probably that SiO₂ and heavy rare earth elements were melt out from the protolith and gradually enriched upward, but Al₂O₃, CaO, MgO, TiO₂ and light rare earth elements enriched downward.

Facile Route to Rare Heterobimetallic Aluminum-Copper and Aluminum-Zinc Selenide Clusters.

PubMed

Li, Bin; Li, Jiancheng; Liu, Rui; Zhu, Hongping; Roesky, Herbert W

2017-03-20

Heterobimetallic aluminum-copper and aluminum-zinc clusters were prepared from the reaction of LAl(SeH) 2 [1; L = HC(CMeNAr) 2 and Ar = 2,6-iPr 2 C 6 H 3 ] with (MesCu) 4 and ZnEt 2 , respectively. The resulting clusters with the core structures of Al 2 Se 4 Cu 4 and Al 2 Se 4 Zn 3 exhibit unique metal-organic frameworks. This is a novel pathway for the synthesis of aluminum-copper and aluminum-zinc selenides. The products have been characterized by spectroscopic methods and single-crystal X-ray structural characterization.

Effects of rare earth doping on multi-core iron oxide nanoparticles properties

NASA Astrophysics Data System (ADS)

Petran, Anca; Radu, Teodora; Borodi, Gheorghe; Nan, Alexandrina; Suciu, Maria; Turcu, Rodica

2018-01-01

New multi-core iron oxide magnetic nanoparticles doped with rare earth metals (Gd, Eu) were obtained by a one step synthesis procedure using a solvothermal method for potential biomedical applications. The obtained clusters were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray microanalysis (EDX), X-ray photoelectron spectroscopy (XPS) and magnetization measurements. They possess high colloidal stability, a saturation magnetization of up to 52 emu/g, and nearly spherical shape. The presence of rare earth ions in the obtained samples was confirmed by EDX and XPS. XRD analysis proved the homogeneous distribution of the trivalent rare earth ions in the inverse-spinel structure of magnetite and the increase of crystal strain upon doping the samples. XPS study reveals the valence state and the cation distribution on the octahedral and tetrahedral sites of the analysed samples. The observed shift of the XPS valence band spectra maximum in the direction of higher binding energies after rare earth doping, as well as theoretical valence band calculations prove the presence of Gd and Eu ions in octahedral sites. The blood protein adsorption ability of the obtained samples surface, the most important factor of the interaction between biomaterials and body fluids, was assessed by interaction with bovine serum albumin (BSA). The rare earth doped clusters surface show higher afinity for binding BSA. In vitro cytotoxicity test results for the studied samples showed no cytotoxicity in low and medium doses, establishing a potential perspective for rare earth doped MNC to facilitate multiple therapies in a single formulation for cancer theranostics.

Fluid evolution in a volcanic-hosted epithermal carbonate-base metal-gold vein system: Alto de la Blenda, Farallón Negro, Argentina

NASA Astrophysics Data System (ADS)

Márquez-Zavalía, M. Florencia; Heinrich, Christoph A.

2016-10-01

Alto de la Blenda is a ˜6.6-Ma intermediate-sulphidation epithermal vein system in the Farallón Negro Volcanic Complex, which also hosts the 7.1-Ma porphyry-Cu-Au deposit of Bajo de la Alumbrera. The epithermal vein system is characterised by a large extent and continuity (2 km × 400 m open to depth × 6 m maximum width) and an average gold grade of ˜8 g/t. The vein is best developed within an intrusion of a fine-grained equigranular monzonite, interpreted as the central conduit of a stratovolcano whose extrusive activity ended prior to porphyry-Cu-Au emplacement at Bajo de la Alumbrera, which is in turn cut by minor epithermal veins. The Alto de la Blenda vein consists predominantly of variably Mn-rich carbonates and quartz, with a few percent of pyrite, sphalerite, galena and other sulphide and sulphosalt minerals. Four phases of vein opening, hydrothermal mineralisation and repeated brecciation can be correlated between different vein segments. Stages 2 and 3 contain the greatest fraction of sulphide and gold. They are separated by the emplacement of a polymictic breccia containing clasts of quartz feldspar porphyry as well as basement rocks. Fluid inclusions in quartz related to stages 2 to 4 are liquid rich with 2-4 wt% NaCl(eq). They homogenise between 160 and 300 °C, with very consistent values within each assemblage. Vapour inclusions are practically absent in the epithermal vein. Quartz fragments in the polymictic breccia contain inclusions of intermediate to vapour-like density and similar low salinity (˜3 wt% NaCl(eq)), besides rare brine inclusions containing halite. Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) analyses of epithermal inclusions indicate high concentrations of K, Fe, As, Sb, Cs, and Pb that significantly vary within and through subsequent vein stages. Careful consideration of detection limits for individual inclusions shows high gold concentrations of ˜0.5 to 3 ppm dissolved in the ore fluid, which contains variably high sulphur concentrations in excess over Fe and other chalcophile metals. Compositional variations are interpreted to reflect cooling and contraction of lower-density magmatic fluids at depth, like those preserved in porphyry clasts that were mechanically transported up by the polymictic breccia. Ore mineral precipitation from the magmatic fluid occurred by further cooling and possibly minor mixing with surface-derived water, leading to sulphide saturation, de-sulphidation of the magmatic fluid and consequent gold precipitation. The absence of flash boiling and/or reduction by carbonaceous host rocks has led to relatively modest but constant gold grades in the carbonate-base metal-gold veins of Alto de la Blenda.

Granulite sulphides as tracers of lower crustal origin and evolution: An example from the Slave craton, Canada

NASA Astrophysics Data System (ADS)

Aulbach, Sonja; Krauss, Cristen; Creaser, Robert A.; Stachel, Thomas; Heaman, Larry M.; Matveev, Sergei; Chacko, Thomas

2010-09-01

We carried out a detailed study of sulphide minerals, a ubiquitous mineral group in lower crustal mafic to peraluminous granulite xenoliths from the Diavik kimberlites, to assess their use in constraining the origin and tectonothermal evolution of the deep crust, and to obtain additional data on the composition of lower crust beneath ancient continents. Sulphides are overwhelmingly pyrrhotite with minor Ni (0.7-3.9 at.%), Co (0.1-0.7 at.%), and Cu contents (0.4-3.9 at.%). Sulphide modes in mafic granulites range from 0.14 to 0.55 vol%, translating into bulk rock S contents from ˜600 to 2000 ppm, similar to S contents in other mafic igneous rocks and indicating preservation of primary igneous S contents. In mafic granulites, Re and Os abundances in sulphides range from 42.5 to 726 ppb and 3.2 to 180 ppb, respectively, whereas those in peraluminous granulites are distinctly lower (36.1-282 ppb and 1.8-7.2 ppb, respectively), suggestive of Re and Os loss to fractionating sulphides in the more evolved precursors of these rocks. The significant within-sample variability of 187Os/ 188Os and correlation with 187Re/ 188Os indicates the preservation of primary Re-Os isotope systematics and time-integrated decay of the measured 187Re. Within the large uncertainties inherent in the nature of the samples and technique, sulphides in some granulites may record major tectonothermal events in the central Slave craton spanning several billion years of evolution. Multiple generations of sulphide can occur in a single sample. These data attest to the heterogeneous composition and complex history of the Slave craton lower crust.

Principal thorium resources in the United States

USGS Publications Warehouse

Staatz, Mortimer Hay; Armbrustmacher, T.J.; Olson, J.C.; Brownfield, I.K.; Brock, M.R.; Lemons, J.F.; Coppa, L.V.; Clingan, B.V.

1979-01-01

Resources were assessed for thorium in the higher grade and better known deposits in the United States in: (1) veins, (2) massive carbonatites, (3) stream placers of North and South Carolina, and (4) disseminated deposits. Thorium resources for the first three categories were divided into reserves and probable potential resources. Each of these then were separated into the following cost categories: (1) the amount of ThO2 producible at less than $15 per pound, (2) the amount producible at between $15 and $30 per pound, and (3) the amount producible at more than $50 per pound. The type of mining and milling needed at each deposit determines the capital, operating, and fixed costs of both mining and milling. Costs start with the clearing of land and are carried through to the final product, which for all deposits is ThO2. Capital costs of mining are affected most by the type of mining and the size of the mine. Those of milling are affected most by the kind of mill, its size, and whether or not extra circuits are needed for the separation of rare earths or some other byproduct. Veins, massive carbonatites, and stream placers of North and South Carolina have reserves of 188,000 short tons of ThO2 and probable potential resources of 505,000 tons of ThO2. Approximately half of the reserves and probable potential resources can be produced at less than $30 per pound of ThO2. Veins are the highest grade source in the United States and have total reserves of 142,000 tons of ThO2 and probable potential resources of 343,000 tons. About 90 percent of the reserves and 91 percent of the probable potential resources can be produced at less than $15 per pound of ThO2. Seven vein districts were evaluated: (1) Lemhi Pass, Mont.-Idaho, (2) Wet Mountains, Colo., (3) Powderhorn, Colo., (4) Hall Mountain, Idaho, (5) Diamond Creek, Idaho, (6) Bear Lodge Mountains, Wyo. and (7) Mountain Pass, Calif. Eighty-seven percent of the total reserves and probable potential resources are in the Lemhi Pass and Wet Mountains Districts. The first district has reserves of 68,000 tons of ThO2 and probable potential resources of 124,000 tons that can be produced at less than $15 per pound; the second district has 54,000 tons of reserves and 141,000 tons of probable potential resources producible at less than $15 per pound. Rare earths are a common byproduct, and in many veins they are from one-half to several times as abundant as thorium. Massive carbonatite bodies are large-tonnage low-grade deposits. Thorium in these deposits would be a byproduct either of rare earth or of niobium mining. The Iron Hill carbonatite body in the Powderhorn district, Colorado, and the Sulfide Queen carbonatite body in the Mountain Pass district, California, were evaluated. These two deposits contain 40,800 tons of ThO2 in reserves and 125,000 tons of ThO2 in probable potential resources. More than 80 percent of this total is in the Iron Hill carbonatite. This thorium is entirely a byproduct and is producible at less than $15 per pound of ThO2. The Sulphide Queen massive carbonatite deposit was being mined in 1977 for rare earths, and thorium could be recovered by adding an extra circuit to the existing mill. Stream placers in North and South Carolina occur both in the Piedmont and just east of the Fall Line. The reserves of these deposits total 5,270 tons of ThO2, and the probable potential resources are 36,800 tons of ThO2. The Piedmont placers are all too small to produce ThO2 at a cost of less than $50 per pound. One placer on Hollow Creek, S.C., just east of the Fall Line had reserves of 2,040 tons of ThO2 that is producible at between $15 and $30 per pound. Thorium occurs in monazite in these placers. Other heavy minerals that would be recovered with the monazite include rutile, zircon, and ilmenite. In addition to thorium, monazite contains large amounts of rare earths and small amounts of uranium; both can be recovered during the process that separates thorium fr

To the Application of LiDAR to Detect the Geological Structures in Sulphurets Property, British Columbia, Canada

NASA Astrophysics Data System (ADS)

Koohzare, A.; Rezaeian, M.; McIntosh, A.

2009-05-01

The Kerr Sulphurets property in North Western British Columbia has been explored primarily as a placer gold holding since the 1880s; and, potentially includes one of Canada's largest gold deposits (e.g. the Mitchell Zone). The Sulphurets camp has been classified by Taylor in 2007 as a prominent global epithermal high-sulphidation subtype with 10 million tonnes of ore (reserves + production) containing approximately 10 g/t gold. The geological and geophysical observations of this deposit indicate intrusion- related mineralized veins which are known to overlap as the result of structural complexities. Faulting predates mineralization and alteration and dramatically dominates the location of the mineralization for this porphyry- epithermal high-sulphidation deposit (Britton and Alldrick 1988, British Columbia Ministry of Energy, Mines and Petroleum Resources, 1992; Margolis, 1993). However, the surface trace of these structures and lineaments within the site is obscured by vegetation, glacial cover and steep topographic relief. We used high resolution LiDAR airborne bare-earth sensing (vegetative data deleted) in an effort to detect the surface geological features and lineaments in the Kerr Sulphurets site. The LiDAR flight was designed to acquire high density data with 2 points per square meter using a 150 kHz multipulse system. High resolution LiDAR data provides a level of detail not achievable by other digital terrain modelling techniques, whether extracted from aerial photography, low-resolution topographic contour maps, 10-30 meter USGS, or SRTM digital elevation models. LiDAR bare-earth data spectacularly revealed hidden geological structures within the property district, which in turn assisted in identifying the high potential zones for mineralization in Sulphurets.

Solidification Based Grain Refinement in Steels

DTIC Science & Technology

2010-07-20

methods which worked in the SVSU foundry. However, additions of NbO powder, FeTi, misch metal , and rare earth silicide were successful. Misch metal ...and rare earth silicide additions at the ladle are the most promising from an industrial stand point. The project group has begun preparing for the... metal and rare earth silicide additions have also reduced grain size and improved hardness. Instructions: You may use this MS Word file to submit the

Experimental Parameters Affecting Stripping of Rare Earth Elements from Loaded Sorptive Media in Simulated Geothermal Brines

DOE Data Explorer

Dean Stull

2016-05-24

Experimental results from several studies exploring the impact of pH and acid volume on the stripping of rare earth elements (REEs) loaded onto ligand-based media via an active column. The REEs in this experiment were loaded onto the media through exposure to a simulated geothermal brine with known mineral concentrations. The data include the experiment results, rare earth element concentrations, and the experimental parameters varied.

Rare Earth Oxide Fluoride Nanoparticles And Hydrothermal Method For Forming Nanoparticles

DOEpatents

Fulton, John L.; Hoffmann, Markus M.

2003-12-23

A hydrothermal method for forming nanoparticles of a rare earth element, oxygen and fluorine has been discovered. Nanoparticles comprising a rare earth element, oxygen and fluorine are also described. These nanoparticles can exhibit excellent refractory properties as well as remarkable stability in hydrothermal conditions. The nanoparticles can exhibit excellent properties for numerous applications including fiber reinforcement of ceramic composites, catalyst supports, and corrosion resistant coatings for high-temperature aqueous solutions.

Rare earth oxide fluoride nanoparticles and hydrothermal method for forming nanoparticles

DOEpatents

Fulton, John L [Richland, WA; Hoffmann, Markus M [Richland, WA

2001-11-13

A hydrothermal method for forming nanoparticles of a rare earth element, oxygen and fluorine has been discovered. Nanoparticles comprising a rare earth element, oxygen and fluorine are also described. These nanoparticles can exhibit excellent refractory properties as well as remarkable stability in hydrothermal conditions. The nanoparticles can exhibit excellent properties for numerous applications including fiber reinforcement of ceramic composites, catalyst supports, and corrosion resistant coatings for high-temperature aqueous solutions.

PROCESSING OF MONAZITE SAND

DOEpatents

Calkins, G.D.; Bohlmann, E.G.

1957-12-01

A process for the recovery of thorium, uranium, and rare earths from monazite sands is presented. The sands are first digested and dissolved in concentrated NaOH, and the solution is then diluted causing precipitation of uranium, thorium and rare earth hydroxides. The precipitate is collected and dissolved in HCl, and the pH of this solution is adjusted to about 6, precipitating the hydroxides of thorium and uranium but leaving the rare earths in solution. The rare earths are then separated from the solution by precipitation at a still higher pH. The thorium and uranium containing precipitate is redissolved in HNO/sub 3/ and the two elements are separated by extraction into tributyl phosphate and back extraction with a weakly acidic solution to remove the thorium.

Rare earth-doped materials with enhanced thermoelectric figure of merit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkatasubramanian, Rama; Cook, Bruce Allen; Levin, Evgenii M.

A thermoelectric material and a thermoelectric converter using this material. The thermoelectric material has a first component including a semiconductor material and a second component including a rare earth material included in the first component to thereby increase a figure of merit of a composite of the semiconductor material and the rare earth material relative to a figure of merit of the semiconductor material. The thermoelectric converter has a p-type thermoelectric material and a n-type thermoelectric material. At least one of the p-type thermoelectric material and the n-type thermoelectric material includes a rare earth material in at least one ofmore » the p-type thermoelectric material or the n-type thermoelectric material.« less

Novel online security system based on rare-earth-doped glass microbeads

NASA Astrophysics Data System (ADS)

Officer, Simon; Prabhu, G. R.; Pollard, Pat; Hunter, Catherine; Ross, Gary A.

2004-06-01

A novel fluorescent security label has been produced that could replace numerous conventional fluorescent dyes in document security. This label utilizes rare earth ions doped in a borosilicate glass matrix to produce sharp spectral fluorescence peaks with characteristic long lifetimes due to the rare earth ions. These are subsequently detected by an online detection system based on fluorescence and the long lifetimes to avoid any interference from other fluorophores present in the background. Security is further enhanced by the interaction of the rare earth ions with each other and the effect of the host on the emission spectra and therefore the number of permutations that could be produced. This creates a very secure label with various applications for the security market.

Comparative effect of a new mouthrinse containing chlorhexidine, triclosan and zinc on volatile sulphur compounds: a randomized, crossover, double-blind study.

PubMed

Mendes, L; Coimbra, J; Pereira, A L; Resende, M; Pinto, M G

2016-08-01

The aims of this study were to compare the volatile sulphur compounds (VSC)-reducing effect of two commercial mouthrinses using a morning bad breath model and to assess the role of mechanical plaque control (MPC) when performed previously to mouthrinse use. Eleven volunteers with good oral health were enrolled in a double-blind, randomized, six-step crossover design study with a 7-day washout period. Two commercial mouthrinses were tested using a saline solution (NaCl 0.9%) as a negative control: one mouthrinse contained 0.05% chlorhexidine, 0.05% cetylpyridinium chloride and 0.14% zinc lactate (CHX-CPC-Zn), while the other contained 0.05% chlorhexidine, 0.15% triclosan and 0.18% zinc pidolate (CHX-triclosan-Zn). A portable sulphide monitor (Halimeter(®) ) was used for VSC quantification. Measurements were made at baseline, and 1, 3 and 5 h after rinsing. Significant differences were detected by analysis of variance. No significant differences between groups were detected at baseline. We were unable to demonstrate a significant influence of mechanical plaque control on the reduction of VSC levels when performed before mouthrinse use (P = 0.631). Both mouthrinses effectively lowered VSC levels in all test intervals (P < 0.05). No statistically significant differences were found between mouthrinses in any of the test intervals (P = 0.629, 0.069 and 0.598 at 1, 3 and 5 h). This study demonstrated that CHX-CPC-Zn and CHX-triclosan-Zn have significant and similar effects in reducing VSC levels, which persist for at least 5 h. Such effects were independent of previous MPC, which failed to improve on the results of mouthrinse use alone. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Influences of Silver and Zinc Contents in the Stannite Ag2ZnSnS4 Photoelectrodes on Their Photoelectrochemical Performances in the Salt-Water Solution.

PubMed

Cheng, Kong-Wei; Hong, Shu-Wei

2018-06-13

The multicomponent metal sulphide (stannite Ag2ZnSnS4) samples were grown onto the conductive metal oxide coated glass substrates by using the sulfurization of co-sputtering silver-zinc-tin precursors. Several [Ag]/[Zn+Sn] and [Zn]/[Sn] ratios were set in the metal precursors to investigate their influences on the crystal phases, microstructures and physical properties of the stannite Ag2ZnSnS4 samples. The results of the crystal phases and compositions of samples showed that the stannite Ag2ZnSnS4 phase can be obtained using the two-step sulfurization process, which maintained the silver-zinc-tin precursors at 160C for 1 hour and then kept them at 450oC for 30 minutes under sulfur/nitrogen atmosphere. N-type stannite Ag2ZnSnS4 samples with the carrier concentrations of 5.54x1012 - 9.11x1012 cm-3 can be obtained. High resistivities of Ag2ZnSnS4 samples were observed due to the low values of carrier concentration. Increasing the silver content in the sample can improve its PEC performance due to the decrease in the sample resistivity. The ratio of [Ag]/[Zn+Sn] kept at 0.8 and ratio of [Zn]/[Sn] set at 0.90 in the stannite Ag2ZnSnS4 sample had the highest photoelectrochemical performance of 0.31 mA.cm-2 with the potential set at 1.23 V vs. relative hydrogen electrode applied on the sample because of it having the lowest charge transfer resistance in electrolyte.

Rapid growth of mineral deposits at artificial seafloor hydrothermal vents

PubMed Central

Nozaki, Tatsuo; Ishibashi, Jun-Ichiro; Shimada, Kazuhiko; Nagase, Toshiro; Takaya, Yutaro; Kato, Yasuhiro; Kawagucci, Shinsuke; Watsuji, Tomoo; Shibuya, Takazo; Yamada, Ryoichi; Saruhashi, Tomokazu; Kyo, Masanori; Takai, Ken

2016-01-01

Seafloor massive sulphide deposits are potential resources for base and precious metals (Cu-Pb-Zn ± Ag ± Au), but difficulties in estimating precise reserves and assessing environmental impacts hinder exploration and commercial mining. Here, we report petrological and geochemical properties of sulphide chimneys less than 2 years old that formed where scientific boreholes vented hydrothermal fluids in the Iheya-North field, Okinawa Trough, in East China Sea. One of these infant chimneys, dominated by Cu-Pb-Zn-rich sulphide minerals, grew a height of 15 m within 25 months. Portions of infant chimneys are dominated by sulphate minerals. Some infant chimneys are sulphide-rich similar to high-grade Cu-Pb-Zn bodies on land, albeit with relatively low As and Sb concentrations. The high growth rate reaching the 15 m height within 25 months is attributed to the large hydrothermal vent more than 50 cm in diameter created by the borehole, which induced slow mixing with the ambient seawater and enhanced efficiency of sulphide deposition. These observations suggest the possibility of cultivating seafloor sulphide deposits and even controlling their growth and grades through manipulations of how to mix and quench hydrothermal fluids with the ambient seawater. PMID:26911272

Ancient hydrothermal seafloor deposits in Eridania basin on Mars

NASA Astrophysics Data System (ADS)

Michalski, Joseph R.; Dobrea, Eldar Z. Noe; Niles, Paul B.; Cuadros, Javier

2017-07-01

The Eridania region in the southern highlands of Mars once contained a vast inland sea with a volume of water greater than that of all other Martian lakes combined. Here we show that the most ancient materials within Eridania are thick (>400 m), massive (not bedded), mottled deposits containing saponite, talc-saponite, Fe-rich mica (for example, glauconite-nontronite), Fe- and Mg-serpentine, Mg-Fe-Ca-carbonate and probable Fe-sulphide that likely formed in a deep water (500-1,500 m) hydrothermal setting. The Eridania basin occurs within some of the most ancient terrain on Mars where striking evidence for remnant magnetism might suggest an early phase of crustal spreading. The relatively well-preserved seafloor hydrothermal deposits in Eridania are contemporaneous with the earliest evidence for life on Earth in potentially similar environments 3.8 billion years ago, and might provide an invaluable window into the environmental conditions of early Earth.

Ancient hydrothermal seafloor deposits in Eridania basin on Mars

PubMed Central

Michalski, Joseph R.; Dobrea, Eldar Z. Noe; Niles, Paul B.; Cuadros, Javier

2017-01-01

The Eridania region in the southern highlands of Mars once contained a vast inland sea with a volume of water greater than that of all other Martian lakes combined. Here we show that the most ancient materials within Eridania are thick (>400 m), massive (not bedded), mottled deposits containing saponite, talc-saponite, Fe-rich mica (for example, glauconite-nontronite), Fe- and Mg-serpentine, Mg-Fe-Ca-carbonate and probable Fe-sulphide that likely formed in a deep water (500–1,500 m) hydrothermal setting. The Eridania basin occurs within some of the most ancient terrain on Mars where striking evidence for remnant magnetism might suggest an early phase of crustal spreading. The relatively well-preserved seafloor hydrothermal deposits in Eridania are contemporaneous with the earliest evidence for life on Earth in potentially similar environments 3.8 billion years ago, and might provide an invaluable window into the environmental conditions of early Earth. PMID:28691699

Geology and description of thorium and rare-earth deposits in the southern Bear Lodge Mountains, northeastern Wyoming

USGS Publications Warehouse

Staatz, M.H.

1983-01-01

The Bear Lodge Mountains are a small northerly trending range approximately 16 km northwest of the Black Hills in the northeast corner of Wyoming. Thorium and rare-earth deposits occur over an area of 16 km 2 in the southern part of these mountains. These deposits occur in the core of the Bear Lodge dome in a large multiple intrusive body made up principally of trachyte and phonolite. Two types of deposits are recognized: disseminated deposits and veins. The disseminated deposits are made up of altered igneous rocks cut by numerous crisscrossing veinlets. The disseminated deposits contain thorium and rare-earth minerals in a matrix consisting principally of potassium feldspar, quartz, and iron and manganese oxides. Total rare-earth content of these deposits is about 27 times that of the thorium content. The general size and shape of the disseminated deposits were outlined by making a radiometric map using a scintillation counter of the entire Bear Lodge core, an area of approximately 30 km 2 . The most favorable part of this area, which was outlined by the 40 countJs (count-per-second) isograd on the radiometric map, was sampled in detail. A total of 341 samples were taken over an area of 10.6 km 2 and analyzed for as many as 60 elements. Rare earths and thorium are the principal commodities of interest in these deposits. Total rare-earth content of these samples ranged from 47 to 27,145 ppm (parts per million), and the thorium content from 9.3 to 990 ppm. The amount of total rare earths of individual samples shows little correlation with that of thorium. Contour maps were constructed using the analytical data for total rare earths, thorium, uranium, and potassium. The total rare-earth and thorium maps can be used to define the size of the deposits based on what cut-off grade may be needed during mining. The size is large as the 2,000 ppm total rare-earth isograd encloses several areas that total 3.22 km 2 in size, and the 200 ppm thorium isograd encloses several areas that total 1.69 km 2 . These deposits could be mined by open pit. The Bear Lodge disseminated deposits have one of the largest resources of both total rare earths and thorium in the United States, and although the grade of both commodities is lower than some other deposits, their large size and relative cheapness of mining make them an important future resource. Vein deposits in the Bear Lodge Mountains include all tabular bodies at least 5 cm thick. Twenty-six veins were noted in this area. These veins are thin and short; the longest vein was traced for only 137 m. Minerals vary greatly in the amount present. Gangue minerals are commonly potassium feldspar, quartz, or cristobalite intermixed with varying amounts of limonite, hematite, and various manganese oxides. Rare earths and thorium occur in the minerals monazite, brockite, and bastnaesite. Thorium content of 35 samples ranged from 0.01 to 1.2 percent, and the total rare-earth content of 21 samples from 0.23 to 9.8 percent. Indicated reserves were calculated to a depth of one-third the exposed length of the vein. Inferred reserves lie in a block surrounding indicated reserves. Indicated reserves of all veins are only 50 t of Th0 2 and 1,360 t of total rare-earth oxides; inferred reserves are 250 t of Th0 2 and 6,810 t of total rare-earth oxides. The Bear Lodge dome, which underlies the greater part of this area, is formed by multiple intrusive bodies of Tertiary age that dome up the surrounding sedimentary rocks. In the southern part of the core, the younger intrusive bodies surround and partly replace a granite of Precambrian age. This granite is approximately 2.6 b.y. old. The sedimentary rocks around the core are (from oldest to youngest): Deadwood Formation of Late Cambrian and Early Ordovician age, Whitewood Limestone of Late Ordovician age, Pahasapa Limestone of Early Mississippian age, Minnelusa Sandstone of Pennsylvanian and Early Permian age, Opeche Formation of Permian age, Minnek

[Effects of rare earth compounds on human peripheral mononuclear cell telomerase and apoptosis].

PubMed

Yu, Li; Dai, Yu-Cheng; Yuan, Zhao-Kang; Li, Jie

2004-07-01

To study the effects of rare earth exposure on human telomerase and apoptosis of human peripheral mononuclear cells (PBMNs). Rare earth mine lot in Xunwu county, the biggest ion absorptive rare earth mine lot of China, was selected as the study site. Another village of Xunwu county, with comparable geological structure and social environment was selected as the control site. Thirty healthy adults were randomly selected from the study site as exposure group and another 30 healthy adults randomly selected from the control site as control group. The blood content of 15 rare earth elements, including La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu and Y, were determined by inductive coupled plasma-source mass spectrometry (ICP-MS). The total contents of rare earth elements in the blood were calculated. The TRAP and FCM assays were carried out to analyse the telomerase and apoptosis of human PBMNCs respectively. In the exposure group, the concentration of La, Ce, Dy and Y were significantly higher (P<0.001), and Pr, Nd, Sm, Gd and Yb were higher than those in the control group (P<0.05). The total content of rare earth in the blood of exposure group showed significant difference compared with control group (P<0.001). Telomerase activity in PBMNs of the exposure group was higher than that in the control group (P<0.05); there were 11 adults in the exposure group (30 adults) and 5 adults in control group (30 adults) showed positive telomerase activity. The average age of the exposure group was (38.69 +/- 8.02) years-old, while the control group was (40.45 +/- 9.02) years-old (P >0.05). It was found that there was a significant relationship between telomerase activity and the total content of rare earth elements (P <0.01). 3. The proportion of apoptosis was not different between the two groups (P >0.05), but the cells in the S-phase and G2-M phase were increased (P <0.01) in the exposed group. The telomerase activity of PBMNs in the rare earth elements exposed group was higher than that of the control group, and there is no effect on apoptotic rate of PBMNs, but may promote the diploid DNA replication, and increase the percentage of G2/M and S phase cells.

Mineral sulphide-lime reactions and effect of CaO/C mole ratio during carbothermic reduction of complex mineral sulphides

NASA Astrophysics Data System (ADS)

Hara, Yotamu Stephen Rainford

2014-01-01

Mineral sulphide (MS)-lime (CaO) ion exchange reactions (MS + CaO = MO + CaS) and the effect of CaO/C mole ratio during carbothermic reduction (MS + CaO + C = M + CaS + CO(g)) were investigated for complex froth flotation mineral sulphide concentrates. Phases in the partially and fully reacted samples were characterised by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The primary phases during mineral sulphide-lime ion exchange reactions are Fe3O4, CaSO4 Cu2S, and CaS. A complex liquid phase of Ca2CuFeO3S forms during mineral sulphide-lime exchange reactions above 1173 K. The formation mechanisms of Ca2CuFeO3S liquid phase are determined by characterising the partially reacted samples. The reduction rate and extent of mineral sulphides in the presence of CaO and C increase with the increase in CaO/C ratio. The metallic phases are surrounded by the CaS rich phase at CaO/C > 1, but the metallic phases and CaS are found as separate phases at CaO/C < 1. Experimental results show that the stoichiometric ratio of carbon should be slightly higher than that of CaO. The reactions between CaO and gangue minerals (SiO2 and Al2O3) are only observed at CaO/C > 1 and the reacted samples are excessively sintered.

Real World of Industrial Chemistry: Technology of the Rare Earths.

ERIC Educational Resources Information Center

Kremers, Howard E.

1985-01-01

The 17 rare earth elements account for one-fifth of the 83 naturally occurring elements and collectively rank as the 22nd most abundant "element." Properties of these elements (including their chemical similarity), their extraction from the earth, and their uses are discussed. (JN)

A double Fe-Ti oxide and Fe-sulphide liquid immiscibility in the Itsindro Gabbro Complex, Madagascar

NASA Astrophysics Data System (ADS)

Augé, Thierry; Bailly, Laurent; Roig, Jean-Yves

2017-11-01

The petrology and mineralogy of the Itsindro complex in south-central Madagascar has been investigated through samples obtained from the 320.7 m-deep Lanjanina borehole. The section consists of a 254 m-thick pyroxenite unit with interbedded gabbro layers that overlies a gabbro unit and is itself overlain by a 19 m-thick granite unit. Most of the structures are sub-horizontal. A weak magmatic layering is locally observed but at the scale of the core, the intrusion does not appear to be a layered complex. Pyroxenite and gabbro show a systematic disseminated mineralization consisting of Fe-Ti-P oxides and Fe-(Cu-Ni) sulphides that takes the form of ilmenite-titanomagnetite ± apatite and pyrrhotite ± chalcopyrite ± pentlandite. In the upper zone, from 90 to 72 m, sub-massive centimetre-to decimetre-sized layers of oxides and sulphides comprise a total of 16 m of sub-massive sulphide (the main mineralized zone). In this mineralized zone the oxide/sulphide ratio is close to 1/1. The sulphide is strongly dominated by pyrrhotite, which may locally contain inclusions of molybdenite crystals with the Re sulphide rheniite (ReS2). Oxides are generally euhedral, included in or attached to the Fe-sulphide, and also locally form sub-massive centimetre-sized bands. Apatite as a cumulus phase is ubiquitous. Locally it may account for 30% of the ore-rich samples and some samples consist of apatite-Fe-Ti oxides-Fe-Cu-Ni sulphides with virtually no silicate. Apatite is the main REE carrier but the total REE content remains low (<90 ppm). Mineral compositions and whole rock geochemistry indicate that the rocks are highly differentiated, and in spite of a relatively limited thickness, the differentiation process is observed. Two zones can be distinguished: from the bottom to 162.8 m we see a decrease in the Mg number of olivine and pyroxene, and a drop in TiO2 and Al2O3 for the latter. A reverse trend is then observed within the pyroxenite unit from the 162.8 m level upwards. The main mineralized zone is located in the upper part of this unit, about 70 m above this discontinuity. The highly differentiated Fe-Ti-P facies of the Lanjanina series in the Itsindro Gabbro Complex have been interpreted as corresponding to the Fe-Ti-P rich, Si-poor member remaining after an immiscible segregation of an evolved mafic magma. The granite dykes and the overlying granite unit represent the second, Si-rich member of the immiscibility process. The presence of large amounts of sulphide is attributed to sulphur contamination of the Fe-Ti-rich liquid. Fe-Ti oxides will tend to crystallize on the sulphide droplets and the accumulation of dense Fe-sulphides (liquid) and associated Fe-Ti oxides (solid) will result in this complex and unusual association taking the form of a net texture.

Inclusions of Sulphide Immiscible Melts in Primitive Olivine Phenocrysts from Mantle-Derived Magmas; Preliminary Results

NASA Astrophysics Data System (ADS)

Danyushevsky, L.; Ryan, C.; Kamenetsky, V.; Crawford, A.

2001-12-01

Sulphide inclusions have been identified in olivine phenocrysts (and in one case in a spinel phenocryst) in primitive volcanic rocks from mid- ocean ridges, subduction-related island arcs and backarc basins. These inclusions represent droplets of an immiscible sulphide melt and are trapped by olivine crystals growing from silicate melts. Sulphide melt is usually trapped as separate inclusions, however combined inclusions of sulphide and silicate melts have also been observed. Sulphide inclusions have rounded shapes and vary in size from several up to 100 microns in diameter. At room temperature sulphide inclusions consist of several phases. These phases are formed as a result of crystallisation of the sulphide melt after it was trapped. Crystallisation occurs due to decreasing temperature in the magma chamber after trapping and/or when magma ascents from the magma chamber during eruptions. In all studied sulphides three different phases can be identified: a high- Fe, low-Ni, low-Cu phase; a high-Fe, high-Ni, low-Cu phase; and high-Fe, low-Ni, high-Cu phase. Low-Cu phases appear to be monomineralic, whereas the high-Cu phase is usually composed of a fine intergrowth of high- and low-Cu phases, resembling the quench 'spinifex' structure. Fe, Ni and Cu are the major elements in all sulphides studied. The amount of Ni decreases with decreasing forsterite content of the host olivine phenocryst, which is an index of the degree of silicate magma fractionation. Since Ni content of the silicate magma is decreasing during fractionation, this indicates either that the immiscible sulfide melt remains in equilibrium with the silicate melt continuously changing its composition during fractionation, or that the sulfide melt is continuously separated from the silicate melt during fractionation, with later formed droplets having lower Ni content due to the lower Ni content of the evolved, stronger fractionated silicate melt. Trace element contents of the sulfide inclusions have been analysed on the proton microprobe at CSIRO in Sydney. The main trace elements in the sulfide inclusions are Zn, Pb, Ag, and Se. Other trace elements are below detection limits, which are normally at a level of several ppm. Zn concentrations (120 +/- 40 ppm) in sulphides are similar to those in silicate melts. This indicates that separation of the sulfide melt does not affect Zn contents of silicate melts. On the contrary, Ag (30 +/- 10 ppm) and Pb (40 +/- 10 ppm) contents in sulphides are at least in order of magnitude higher than in the silicate melt, and thus separation of the immiscible sulfide melt can significantly decrease Pb and Ag contents of the silicate magma. The widespread occurrence of sulfide inclusions, which were also described in olivine phenocrysts from ocean island basalts, indicates common saturation at low pressure of mantle-derived magmas with reduced sulfur.

[An investigation of lanthanum and other metals levels in blood, urine and hair among residents in the rare earth mining area of a city in China].

PubMed

Bao, T M; Tian, Y; Wang, L X; Wu, T; Lu, L N; Ma, H Y; Wang, L

2018-02-20

Objective: To investigate the levels of lanthanum, cerium, praseodymium, and neodymium in the blood, urine, and hair samples from residents in the rare earth mining area of a city in China, and to provide a scientific basis for the control of rare earth pollution and the protection of population health. Methods: A total of 147 residents who had lived in the rare earth mining area of a city for a long time were selected as the exposure group, and 108 residents in Guyang County of this city who lived 91 km away from the rare earth mining area were selected as the control group. Blood, urine, and hair samples were collected from the residents in both groups. Inductively coupled plasma mass spectrometry was used to determine the content of lanthanum, cerium, praseodymium, and neodymium in blood, urine, and hair samples. Results: In the exposure group, the median levels of lanthanum, cerium, praseodymium, and neodymium were 0.854, 1.724, 0.132, and 0.839 μg/L, respectively, in blood samples, 0.420, 0.920, 0.055, and 0.337 μg/L, respectively, in urine samples, and 0.052, 0.106, 0.012, and 0.045 μg/g, respectively, in hair samples. The exposure group had significantly higher levels of the four rare earth elements in blood, urine, and hair samples than the control group ( P <0.01) . Conclusion: The residents in the rare earth mining area of this city have higher content of lanthanum, cerium, praseodymium, and neodymium in blood, urine, and hair than those in the non-mining area; the content of cerium is highest, followed by lanthanum, neodymium, and praseodymium.

Magnetic Partitioning Nanofluid for Rare Earth Extraction from Geothermal Fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrail, Bernard P.; Thallapally, Praveen K.; Liu, Jian

Rare earth metals are critical materials in a wide variety of applications in generating and storing renewable energy and in designing more energy efficient devices. Extracting rare earth metals from geothermal brines is a very challenging problem due to the low concentrations of these elements and engineering challenges with traditional chemical separations methods involving packed sorbent beds or membranes that would impede large volumetric flow rates of geothermal fluids transitioning through the plant. We are demonstrating a simple and highly cost-effective nanofluid-based method for extracting rare earth metals from geothermal brines. Core-shell composite nanoparticles are produced that contain a magneticmore » iron oxide core surrounded by a shell made of silica or metal-organic framework (MOF) sorbent functionalized with chelating ligands selective for the rare earth elements. By introducing the nanoparticles at low concentration (≈0.05 wt%) into the geothermal brine after it passes through the plant heat exchanger, the brine is exposed to a very high concentration of chelating sites on the nanoparticles without need to pass through a large and costly traditional packed bed or membrane system where pressure drop and parasitic pumping power losses are significant issues. Instead, after a short residence time flowing with the brine, the particles are effectively separated out with an electromagnet and standard extraction methods are then applied to strip the rare earth metals from the nanoparticles, which are then recycled back to the geothermal plant. Recovery efficiency for the rare earths at ppm level has now been measured for both silica and MOF sorbents functionalized with a variety of chelating ligands. A detailed preliminary techno-economic performance analysis of extraction systems using both sorbents showed potential to generate a promising internal rate of return (IRR) up to 20%.« less

Solvent Extraction of Rare Earth Elements from a Nitric Acid Leach Solution of Apatite by Mixtures of Tributyl Phosphate and Di-(2-ethylhexyl) Phosphoric Acid

NASA Astrophysics Data System (ADS)

Ferdowsi, Ali; Yoozbashizadeh, Hossein

2017-12-01

Solvent extraction of rare earths from nitrate leach liquor of apatite using mixtures of tributyl phosphate (TBP) and di-(2-ethylhexyl) phosphoric acid (D2EHPA) was studied. The effects of nitrate and hydrogen ion concentration of the aqueous phase as well as the composition and concentration of extractants in the organic phase on the extraction behavior of lanthanum, cerium, neodymium, and yttrium were investigated. The distribution ratio of REEs increases by increasing the nitrate concentration in aqueous phase and concentration of extractants in organic phase, but the hydrogen ion concentration in aqueous phase has a decreasing effect. Yttrium as a heavy rare earth is more sensitive to these parameters than light rare earth elements. Although the composition of organic phase has a minor effect on the extraction of light rare earths, the percent of extraction of yttrium decreases dramatically by increasing the TBP content of organic phase. Mixtures of TBP and D2EHPA can show either synergism or antagonism extraction depending on the concentration and composition of extractants in organic phase. The best condition for separating rare earth elements in groups of heavy and light REEs can be achieved at high nitrate concentration, low H+ concentration, and high concentration of D2EHPA in organic phase. Separation of Ce and La by TBP and D2EHPA is practically impossible in the studied conditions; however, low nitrate concentration and high hydrogen ion concentration in aqueous phase and low concentration of extractants in organic phase favor the separation of Nd from other light rare earth elements.

Nanocrystalline semiconductor doped rare earth oxide for the photocatalytic degradation studies on Acid Blue 113: A di-azo compound under UV slurry photoreactor.

PubMed

Suganya Josephine, G A; Mary Nisha, U; Meenakshi, G; Sivasamy, A

2015-11-01

Preventive measures for the control of environmental pollution and its remediation has received much interest in recent years due to the world-wide increase in the contamination of water bodies. Contributions of these harmful effluents are caused by the leather processing, pharmaceutical, cosmetic, textile, agricultural and other chemical industries. Nowadays, advanced oxidation processes considered to be better option for the complete destruction of organic contaminants in water and wastewater. Acid Blue 113 is a most widely used di-azo compound in leather, textile, dying and food industry as a color rending compound. In the present study, we have reported the photo catalytic degradation of Acid Blue 113 using a nanocrystalline semiconductor doped rare earth oxide as a photo catalyst under UV light irradiation. The photocatalyst was prepared by a simple precipitation technique and were characterized by XRD, FT-IR, UV-DRS and FE-SEM analysis. The experimental results proved that the prepared photo catalyst was nanocrystalline and highly active in the UV region. The UV-DRS results showed the band gap energy was 3.15eV for the prepared photo catalyst. The photodegradation efficiency was analyzed by various experimental parameters such as pH, catalyst dosage, variation of substrate concentration and effect of electrolyte addition. The photo degradation process followed a pseudo first order kinetics and was continuously monitored by UV-visible spectrophotometer. The experimental results proved the efficacy of the nanocrystalline zinc oxide doped dysprosium oxide which are highly active under UV light irradiations. It is also suggested that the prepared material would find wider applications in environmental remediation technologies to remove the carcinogenic and toxic moieties present in the industrial effluents. Copyright © 2015 Elsevier Inc. All rights reserved.

The Influence of Novel Alloying Additions on the Performance of Magnesium Alloy AZ31B

DTIC Science & Technology

2013-11-01

More recently, alloys using a variety of the rare earth elements have been developed. Typically, these alloys have shown significant improvements...in mechanical properties and to a lesser degree in corrosion performance. However, rare earth elements are often costly and heavier than Mg. Thus...1.0 0.004 Max — — Note: Fe = iron; RE = rare earth . SEM micrograph and energy-dispersive x-ray (EDX) results for selected alloys are shown in

Rare Earth Optical Temperature Sensor

NASA Technical Reports Server (NTRS)

Chubb, Donald L. (Inventor); Jenkins, Phillip (Inventor)

2004-01-01

A rare earth optical temperature sensor is disclosed for measuring high temperatures. Optical temperature sensors exist that channel emissions from a sensor to a detector using a light pipe. The invention uses a rare earth emitter to transform the sensed thermal energy into a narrow band width optical signal that travels to a detector using a light pipe. An optical bandpass filter at the detector removes any noise signal outside of the band width of the signal from the emitter.

China’s Ace in the Hole Rare Earth Elements

DTIC Science & Technology

2010-01-01

before losing magnetism. 11 Europium sesquioxide (Eu203) has been tested as neutron absorbers for control rods in (fast breeder ) nuclear reactors ...sources of rare earth around the world, it could take anywhere from 10 to 15 years from the time of discovery to begin a full- scale rare earth...television/computer screens, it is being studied for possible use in nuclear reactors .11 Erbium is used as an amplifier for fiber optic data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selle, J.E.

A modification was made to the Kaufman method of calculating binary phase diagrams to permit calculation of intra-rare earth diagrams. Atomic volumes for all phases, real or hypothetical, are necessary to determine interaction parameters for calculation of complete diagrams. The procedures used to determine unknown atomic volumes are describes. Also, procedures are described for determining lattice stability parameters for unknown transformations. Results are presented on the calculation of intra-rare earth diagrams between both trivalent and divalent rare earths. 13 refs., 36 figs., 11 tabs.

Rare earth elements and permanent magnets (invited)

NASA Astrophysics Data System (ADS)

Dent, Peter C.

2012-04-01

Rare earth (RE) magnets have become virtually indispensible in a wide variety of industries such as aerospace, automotive, electronics, medical, and military. RE elements are essential ingredients in these high performance magnets based on intermetallic compounds RECo5, RE2TM17 (TM: transition metal), and RE2TM14B. Rare earth magnets are known for their superior magnetic properties—high induction, and coercive force. These properties arise due to the extremely high magnetocrystalline anisotropy made possible by unique 3d-4f interactions between transition metals and rare earths. For more than 40 years, these magnets remain the number one choice in applications that require high magnetic fields in extreme operating conditions—high demagnetization forces and high temperature. EEC produces and specializes in RECo5 and RE2TM17 type sintered magnets. Samarium and gadolinium are key RE ingredients in the powder metallurgical magnet production processes which include melting, crushing, jet milling, pressing, sintering, and heat treating. The magnetic properties and applications of these magnets will be discussed. We will also briefly discuss the past, current, and future of the permanent magnet business. Currently, over 95% of all pure rare earth oxides are sourced from China, which currently controls the market. We will provide insights regarding current and potential new magnet technologies and designer choices, which may mitigate rare earth supply chain issues now and into the future.

Influence of rare earth content on Mm-based AB 5 metal hydride alloys for Ni-MH batteries-An X-ray fluorescence study

NASA Astrophysics Data System (ADS)

Ananth, M. V.; Raju, M.; Manimaran, K.; Balachandran, G.; Nair, Lekshmi M.

AB 5-type MH alloys with Mm (Misch metal) as the A part (with varied rare earth contents in Mm) were investigated for rare earth by XRF analysis and battery performance by life cycle tests with an objective of understanding the influence of rare earth content on electrochemical hydrogen storage. The La/Ce ratio was found to vary from 0.51 to 18.73. The capacity output varied between 179 and 266 mAh g -1. The results show that the La/Ce ratio has a strong influence on the performance, with the best performance realized with samples having an La/Ce ratio of around 12. La enhancement facilitates easy activation due to refinement in grain size and interstitial dimensions. Also, an orderly influence on crystalline structure could be seen. The study demonstrates that the rare earth content is an essential factor in determining the maximum capacity output because of its influence on crystal orientation as well as an increase in the radius of the interstitials, lattice constants and cell volumes.

Investigation of the magnetic properties in double perovskite R2CoMnO6 single crystals (R  =  rare earth: La to Lu).

PubMed

Kim, M K; Moon, J Y; Choi, H Y; Oh, S H; Lee, N; Choi, Y J

2015-10-28

We have successfully synthesized the series of the double-perovskite R2CoMnO6 (R  =  rare earth: La to Lu) single crystals and have investigated their magnetic properties. The ferromagnetic order of Co(2+)/Mn(4+) spins emerges mainly along the c axis. Upon decreasing the size of rare earth ion, the magnetic transition temperature decreases linearly from 204 K for La2CoMnO6 to 48 K for Lu2CoMnO6, along with the enhancement of monoclinic distortion. The temperature and magnetic-field dependences of magnetization reveal the various magnetic characteristics such as the metamagnetic transition in R  =  Eu, the isotropic nature of rare earth moment in R  =  Gd, and the reversal of magnetic anisotropy in R  =  Tb and Dy. Our results offer comprehensive information for understanding the roles of mixed-valent magnetic ions and rare earth magnetic moments on the magnetic properties.

Fast preconcentration of trace rare earth elements from environmental samples by di(2-ethylhexyl)phosphoric acid grafted magnetic nanoparticles followed by inductively coupled plasma mass spectrometry detection

NASA Astrophysics Data System (ADS)

Yan, Ping; He, Man; Chen, Beibei; Hu, Bin

2017-10-01

In this work, di(2-ethylhexyl)phosphoric acid (P204) grafted magnetic nanoparticles were synthesized by fabricating P204 onto Fe3O4@TiO2 nanoparticles based on Lewis acid-base interaction between Ti and phosphate group under weakly acidic condition. The prepared Fe3O4@TiO2@P204 nanoparticles exhibited excellent selectivity for rare earth elements, and good anti-interference ability. Based on it, a method of magnetic solid phase extraction (MSPE) combined with inductively coupled plasma mass spectrometry (ICP-MS) was developed for fast preconcentration and determination of trace rare earth elements in environmental samples. Under the optimal conditions, the detection limits of rare earth elements were in the range of 0.01 (Tm)-0.12 (Nd) ng L- 1 with an enrichment factor of 100-fold, and the relative standard deviations ranged from 4.9 (Pr) to 10.7% (Er). The proposed method was successfully applied to the determination of rare earth elements in environmental samples, including river water, lake water, seawater and sediment.

A multi-analytical investigation of semi-conductor pigments with time-resolved spectroscopy and imaging

NASA Astrophysics Data System (ADS)

Nevin, A.; Cesaratto, A.; D'Andrea, C.; Valentini, Gianluca; Comelli, D.

2013-05-01

We present the non-invasive study of historical and modern Zn- and Cd-based pigments with time-resolved fluorescence spectroscopy, fluorescence multispectral imaging and fluorescence lifetime imaging (FLIM). Zinc oxide and Zinc sulphide are semiconductors which have been used as white pigments in paintings, and the luminescence of these pigments from trapped states is strongly dependent on the presence of impurities and crystal defects. Cadmium sulphoselenide pigments vary in hue from yellow to deep red based on their composition, and are another class of semiconductor pigments which emit both in the visible and the near infrared. The Fluorescence lifetime of historical and modern pigments has been measured using both an Optical Multichannel Analyser (OMA) coupled with a Nd:YAG nslaser, and a streak camera coupled with a ps-laser for spectrally-resolved fluorescence lifetime measurements. For Znbased pigments we have also employed Fluorescence Lifetime Imaging (FLIM) for the measurement of luminescence. A case study of FLIM applied to the analysis of the painting by Vincent Van Gogh on paper - "Les Bretonnes et le pardon de Pont-Aven" (1888) is presented. Through the integration of complementary, portable and non-invasive spectroscopic techniques, new insights into the optical properties of Zn- and Cd-based pigments have been gained which will inform future analysis of late 19th] and early 20th C. paintings.

GROWTH AND CHARACTERIZATION OF SINGLE CRYSTALS OF RARE EARTH COMPOUNDS.

DTIC Science & Technology

SINGLE CRYSTALS, CRYSTAL GROWTH), (*CRYSTAL GROWTH, SINGLE CRYSTALS), (*RARE EARTH COMPOUNDS, SINGLE CRYSTALS), EPITAXIAL GROWTH, SODIUM COMPOUNDS, CHLORIDES, VAPOR PLATING, ELECTROSTATIC FIELDS, ENERGY, ATOMIC PROPERTIES , BONDING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rudyk, Brent W.; Stoyko, Stanislav S.; Mar, Arthur, E-mail: arthur.mar@ualberta.ca

Six quaternary rare-earth-containing sulphides RE{sub 3}MInS{sub 7} (M=Fe, Co, Ni) have been prepared by reactions of the elements at 1050–1150 °C. They are the first examples of chalcogenides RE{sub 3}MM'Ch{sub 7} adopting related La{sub 3}CuSiS{sub 7}- or ordered Ce{sub 3}Al{sub 1.67}S{sub 7}-type structures in which the M' component is indium. They crystallize in the noncentrosymmetric hexagonal space group P6{sub 3} with Z=2 and cell parameters in the ranges of a=9.95–10.15 Å and c=6.25–6.29 Å for RE{sub 3}FeInS{sub 7} (RE=La–Pr), RE{sub 3}CoInS{sub 7} (RE=La, Ce), and La{sub 3}NiInS{sub 7}. The crystal structure consists of parallel chains of face-sharing M-centred octahedra andmore » stacks of In-centred tetrahedra, all pointing in the same polar direction, with seven-coordinate La atoms in the intervening spaces. X-ray photoelectron spectra support the valence assignments implied by the formulation (RE{sup 3+}){sub 3}(M{sup 2+})(In{sup 3+})(S{sup 2−}){sub 7}. Magnetic measurements are suggestive of antiferromagnetic coupling between the M moments. Band structure calculations reveal that a band gap of 0.25 eV is present in La{sub 3}FeInS{sub 7}, whereas the increased electron count in La{sub 3}CoInS{sub 7} and La{sub 3}NiInS{sub 7} causes the Fermi level to cut narrow bands. - Graphical abstract: RE{sub 3}MInS{sub 7} (M=Fe, Co, Ni) consists of chains of face-sharing M-centred octahedra and stacks of In-centred tetrahedra. - Highlights: • Six members of noncentrosymmetric sulphide series RE{sub 3}MInS{sub 7} have been prepared. • They are the first examples of chalcogenides RE{sub 3}MM'Ch{sub 7} with In atoms in M' site. • X-ray photoelectron spectra support the formulation (RE{sup 3+}){sub 3}(M{sup 2+})(In{sup 3+})(S{sup 2−}){sub 7}. • Band structure calculations suggest semiconducting or metallic behaviour.« less

Coated conductors

DOEpatents

Arendt, Paul N.; Foltyn, Stephen R.; Stan, Liliana; Usov, Igor O.; Wang, Haiyan

2010-06-15

Articles are provided including a base substrate having a layer of an IBAD oriented material thereon, and, a layer of barium-containing material selected from the group consisting of barium zirconate, barium hafnate, barium titanate, barium strontium titanate, barium dysprosium zirconate, barium neodymium zirconate and barium samarium zirconate, or a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the layer of an IBAD oriented material. Such articles can further include thin films of high temperature superconductive oxides such as YBCO upon the layer of barium-containing material selected from the group consisting of barium zirconate, barium hafnate, barium titanate, barium strontium titanate, barium dysprosium zirconate, barium neodymium zirconate and barium samarium zirconate, or a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates.

Method of forming magnetostrictive rods from rare earth-iron alloys

DOEpatents

McMasters, O.D.

1986-09-02

Rods of magnetostrictive alloys of iron with rare earth elements are formed by flowing a body of rare earth-iron alloy in a crucible enclosed in a chamber maintained under an inert gas atmosphere, forcing such molten rare-earth-iron alloy into a hollow mold tube of refractory material positioned with its lower end portion within the molten body by means of a pressure differential between the chamber and mold tube and maintaining a portion of the molten alloy in the crucible extending to a level above the lower end of the mold tube so that solid particles of higher melting impurities present in the alloy collect at the surface of the molten body and remain within the crucible as the rod is formed in the mold tube. 5 figs.

Superposition-model analysis of rare-earth doped BaY2F8

NASA Astrophysics Data System (ADS)

Magnani, N.; Amoretti, G.; Baraldi, A.; Capelletti, R.

The energy level schemes of four rare-earth dopants (Ce3+ , Nd3+ , Dy3+ , and Er3+) in BaY2 F-8 , as determined by optical absorption spectra, were fitted with a single-ion Hamiltonian and analysed within Newman's Superposition Model for the crystal field. A unified picture for the four dopants was obtained, by assuming a distortion of the F- ligand cage around the RE site; within the framework of the Superposition Model, this distortion is found to have a marked anisotropic behaviour for heavy rare earths, while it turns into an isotropic expansion of the nearest-neighbours polyhedron for light rare earths. It is also inferred that the substituting ion may occupy an off-center position with respect to the original Y3+ site in the crystal.

Method of forming magnetostrictive rods from rare earth-iron alloys

DOEpatents

McMasters, O. Dale

1986-09-02

Rods of magnetrostructive alloys of iron with rare earth elements are formed by flowing a body of rare earth-iron alloy in a crucible enclosed in a chamber maintained under an inert gas atmosphere, forcing such molten rare-earth-iron alloy into a hollow mold tube of refractory material positioned with its lower end portion within the molten body by means of a pressure differential between the chamber and mold tube and maintaining a portion of the molten alloy in the crucible extending to a level above the lower end of the mold tube so that solid particles of higher melting impurities present in the alloy collect at the surface of the molten body and remain within the crucible as the rod is formed in the mold tube.

DFT study of CdS-PVA film

NASA Astrophysics Data System (ADS)

Bala, Vaneeta; Tripathi, S. K.; Kumar, Ranjan

2015-02-01

Density functional theory has been applied to study cadmium sulphide-polyvinyl alcohol nanocomposite film. Structural models of two isotactic-polyvinyl alcohol (I-PVA) chains around one cadmium sulphide nanoparticle is considered in which each chain consists three monomer units of [-(CH2CH(OH))-]. All of the hydroxyl groups in I-PVA chains are directed to cadmium sulphide nanoparticle. Electronic and structural properties are investigated using ab-intio density functional code, SIESTA. Structural optimizations are done using local density approximations (LDA). The exchange correlation functional of LDA is parameterized by the Ceperley-Alder (CA) approach. The core electrons are represented by improved Troulier-Martins pseudopotentials. Densities of states clearly show the semiconducting nature of cadmium sulphide polyvinyl alcohol nanocomposite.

Distribution Analysis of Sulphide Mineral (Pyrite) Using Induced Polarization Method in Libureng, Bone, South Sulawesi

NASA Astrophysics Data System (ADS)

Altin Massinai, Muhammad; Lantu; Latuconsina, Hidayat; Fawzy Ismullah M, Muhammad

2018-03-01

Sulphide minerals are any member of a group of compounds of sulphur with one or more metals. Some of these sulphide minerals are economically important. This study used induced polarization method to identify distribution and mineralized zone of sulphide mineral (Pyrite), in Libureng, Bone Regency, South Sulawesi. The data processing yielded resistivity value, percent frequency effect (PPE) value, and metal factor (MF) value which were then used to produce 2-D and 3-D section model. Based on the data interpretation, an anomaly linked to pyrite deposits was seen in four trajectories with resistivity value < = 50, PFE = > 3%, and MF > = 150, deposited in hydrothermal alteration zone, sericite zone.

40 CFR 421.271 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Rare Earth Metals... rare earths to about 94-99 percent. The balance of tha alloy includes traces of other elements and one...

Hypoxic pulmonary vasoconstriction in isolated rat pulmonary arteries is not inhibited by antagonists of H2S-synthesizing pathways

PubMed Central

Prieto-Lloret, Jesus; Shaifta, Yasin; Ward, Jeremy P T; Aaronson, Philip I

2015-01-01

An increase in the H2S (hydrogen sulphide, hereafter sulphide) concentration in pulmonary artery smooth muscle cells (PASMCs) has been proposed to mediate hypoxic pulmonary vasoconstriction (HPV). We evaluated this hypothesis in isolated rat intrapulmonary arteries (IPAs) by examining the effects of the sulphide precursor cysteine and sulphide-synthesis blockers on HPV and also on normoxic pulmonary vasoconstriction (NPV) stimulated by prostaglandin F2α (PGF2α) and by the drug LY83583, which causes contraction in IPAs by increasing cellular reactive oxygen species levels. Experiments with several blockers of cystathionine γ-lyase (CSE), the enzyme responsible for sulphide synthesis in the vasculature, demonstrated that propargylglycine (PAG, 1 mm) had little or no effect on the NPV caused by PGF2α or LY83583. Conversely, other CSE antagonists tested, aminooxyacetic acid (AOAA, 100 μm), β-cyanoalanine (BCA, 500 μm) and hydroxylamine (HA, 100 μm), altered the NPV to PGF2α (BCA increased, HA inhibited) and/or LY83583 (BCA increased, AOAA and HA inhibited). Preincubating IPAs in physiological saline solution (PSS) containing 1 mm cysteine increased the amplitude of the NPV to PGF2α by ∼50%, and had a similar effect on HPV elicited by hypoxic challenge with 0% O2. The enhancement of both responses by cysteine was abolished by pretreatment with 1 mm PAG. Measurements carried out with an amperometric electrode demonstrated that incubation with 1 mm cysteine under anoxic conditions (to minimize sulphide oxidation) greatly potentiated the release of sulphide from pieces of rat liver and that this release was strongly antagonized by PAG, indicating that at this concentration PAG could enter cells intact and antagonize CSE. PAG at 1 mm had no effect on HPV recorded in control PSS, or in PSS supplemented with physiological concentrations of cysteine (10 μm), cystine (50 μm) and glutamate (100 μm) in order to prevent the possible depletion of intracellular cysteine during experiments. Application of a combination of 1 mm cysteine and 1 mm α-ketoglutarate to promote sulphide synthesis via the cysteine aminotransferase/mercaptopyruvate sulphurtransferase (CAT/MST) pathway caused an increase in HPV similar to that observed for cysteine. This was partially blocked by the CAT antagonist aspartate (1 mm) and also by PAG. However, HPV was not increased by 1 mm α-ketoglutarate alone, and HPV in the absence of α-ketoglutarate and cysteine was not attenuated by aspartate. Pretreatment of IPAs with dithiothreitol (DTT, 1 mm), proposed to promote the conversion of mitochondrial thiosulphate to sulphide, did not increase the release of sulphide from pieces of rat liver in either the presence or the absence of 1 mm cysteine, and virtually abolished HPV. The results provide evidence that the sulphide precursor cysteine can promote both NPV and HPV in rat IPA by generating sulphide via a PAG-sensitive pathway, presumably CSE. However, HPV evoked under control conditions was unaffected by the blockade of CSE. Moreover, HPV was not affected by the CAT antagonist aspartate and was blocked rather than enhanced by DTT. The data therefore indicate that sulphide generated by CSE or CAT/MST or from thiosulphate is unlikely to contribute to O2 sensing during HPV in these arteries. PMID:25630260

Voltage Control of Rare-Earth Magnetic Moments at the Magnetic-Insulator-Metal Interface

NASA Astrophysics Data System (ADS)

Leon, Alejandro O.; Cahaya, Adam B.; Bauer, Gerrit E. W.

2018-01-01

The large spin-orbit interaction in the lanthanides implies a strong coupling between their internal charge and spin degrees of freedom. We formulate the coupling between the voltage and the local magnetic moments of rare-earth atoms with a partially filled 4 f shell at the interface between an insulator and a metal. The rare-earth-mediated torques allow the power-efficient control of spintronic devices by electric-field-induced ferromagnetic resonance and magnetization switching.

Thermal Expansion and Thermal Conductivity of Rare Earth Silicates

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Lee, Kang N.; Bansal, Narottam P.

2006-01-01

Rare earth silicates are considered promising candidate materials for environmental barrier coatings applications at elevated temperature for ceramic matrix composites. High temperature thermophysical properties are of great importance for coating system design and development. In this study, the thermal expansion and thermal conductivity of hot-pressed rare earth silicate materials were characterized at temperatures up to 1400 C. The effects of specimen porosity, composition and microstructure on the properties were also investigated. The materials processing and testing issues affecting the measurements will also be discussed.

Energetic Ionic Liquids Based on Anionic Rare Earth Nitrate Complexes (Preprint)

DTIC Science & Technology

2008-07-10

a glass transition temperature (Tg) at -46 oC. However, it is only stable in dry air, and thus must be protected from water. At 75 oC, clear weight...involved highly toxic and corrosive chemicals, N2O4 and NOCl. Ligands which coordinate via oxygen atoms to a rare earth metal ion give rise to stable...complexes. Thus higher air and thermal stabilities may be obtained by introducing rare earth metal nitrates as main components of ionic liquids. We

Rare-Earth Metals and Their Applications in Aviation

DTIC Science & Technology

1984-08-01

metals are not as common as iron and steel which are visible everywhere, yet they are not unfamiliar to us. We often encounter them in everyday life...the flint of a lighter. It is an alloy of rare-earth metal and iron . It contains about 30% iron and the remainder is a composite rare-earth alloy...used to manufacture the detonators of bullets and shells as well as the pyrophoric alloys of firing devices. This type of alloy has a 49.5% content of

Natural and sexual selection against immigrants maintains differentiation among micro-allopatric populations.

PubMed

Tobler, M; Riesch, R; Tobler, C M; Schulz-Mirbach, T; Plath, M

2009-11-01

Local adaptation to divergent environmental conditions can promote population genetic differentiation even in the absence of geographic barriers and hence lead to speciation. But what mechanisms contribute to reproductive isolation among diverging populations? We tested for natural and sexual selection against immigrants in a fish species inhabiting (and adapting to) nonsulphidic surface habitats, sulphidic surface habitats and a sulphidic cave. Gene flow is strong among sample sites situated within the same habitat type, but low among divergent habitat types. Our results indicate that females of both sulphidic populations discriminate against immigrant males during mate choice. Furthermore, using reciprocal translocation experiments, we document natural selection against migrants between nonsulphidic and sulphidic habitats, whereas migrants between sulphidic cave and surface habitats did not exhibit increased mortality within the same time period. Consequently, both natural and sexual selection may contribute to isolation among parapatric populations, and selection against immigrants may be a powerful mechanism facilitating speciation among locally adapted populations even over very small spatial distances.

Sulphurous Mineral Waters: New Applications for Health

PubMed Central

Carbajo, Jose Manuel

2017-01-01

Sulphurous mineral waters have been traditionally used in medical hydrology as treatment for skin, respiratory, and musculoskeletal disorders. However, driven by recent intense research efforts, topical treatments are starting to show benefits for pulmonary hypertension, arterial hypertension, atherosclerosis, ischemia-reperfusion injury, heart failure, peptic ulcer, and acute and chronic inflammatory diseases. The beneficial effects of sulphurous mineral waters, sulphurous mud, or peloids made from sulphurous mineral water have been attributed to the presence of sulphur mainly in the form of hydrogen sulphide. This form is largely available in conditions of low pH when oxygen concentrations are also low. In the organism, small amounts of hydrogen sulphide are produced by some cells where they have numerous biological signalling functions. While high levels of hydrogen sulphide are extremely toxic, enzymes in the body are capable of detoxifying it by oxidation to harmless sulphate. Hence, low levels of hydrogen sulphide may be tolerated indefinitely. In this paper, we review the chemistry and actions of hydrogen sulphide in sulphurous mineral waters and its natural role in body physiology. This is followed by an update of available data on the impacts of exogenous hydrogen sulphide on the skin and internal cells and organs including new therapeutic possibilities of sulphurous mineral waters and their peloids. PMID:28484507

Effects of extreme habitat conditions on otolith morphology: a case study on extremophile live bearing fishes (Poecilia mexicana, P. sulphuraria).

PubMed

Schulz-Mirbach, Tanja; Riesch, Rüdiger; García de León, Francisco J; Plath, Martin

2011-12-01

Our study was designed to evaluate if, and to what extent, restrictive environmental conditions affect otolith morphology. As a model, we chose two extremophile livebearing fishes: (i) Poecilia mexicana, a widespread species in various Mexican freshwater habitats, with locally adapted populations thriving in habitats characterized by the presence of one (or both) of the natural stressors hydrogen sulphide and darkness, and (ii) the closely related Poecilia sulphuraria living in a highly sulphidic habitat (Baños del Azufre). All three otolith types (lapilli, sagittae, and asterisci) of P. mexicana showed a decrease in size ranging from the non-sulphidic cave habitat (Cueva Luna Azufre), to non-sulphidic surface habitats, to the sulphidic cave (Cueva del Azufre), to sulphidic surface habitats (El Azufre), to P. sulphuraria. Although we found a distinct differentiation between ecotypes with respect to their otolith morphology, no clear-cut pattern of trait evolution along the two ecological gradients was discernible. Otoliths from extremophiles captured in the wild revealed only slight similarities to aberrant otoliths found in captive-bred fish. We therefore hypothesize that extremophile fishes have developed coping mechanisms enabling them to avoid aberrant otolith growth - an otherwise common phenomenon in fishes reared under stressful conditions. Copyright © 2011 Elsevier GmbH. All rights reserved.

Lactate has the potential to promote hydrogen sulphide formation in the human colon.

PubMed

Marquet, Perrine; Duncan, Sylvia H; Chassard, Christophe; Bernalier-Donadille, Annick; Flint, Harry J

2009-10-01

High concentrations of sulphide are toxic for the gut epithelium and may contribute to bowel disease. Lactate is a favoured cosubstrate for the sulphate-reducing colonic bacterium Desulfovibrio piger, as shown here by the stimulation of sulphide formation by D. piger DSM749 by lactate in the presence of sulphate. Sulphide formation by D. piger was also stimulated in cocultures with the lactate-producing bacterium Bifidobacterium adolescentis L2-32. Other lactate-utilizing bacteria such as the butyrate-producing species Eubacterium hallii and Anaerostipes caccae are, however, expected to be in competition with the sulphate-reducing bacteria (SRB) for the lactate formed in the human colon. Strains of E. hallii and A. caccae produced 65% and 96% less butyrate from lactate, respectively, in a coculture with D. piger DSM749 than in a pure culture. In triculture experiments involving B. adolescentis L2-32, up to 50% inhibition of butyrate formation by E. hallii and A. caccae was observed in the presence of D. piger DSM749. On the other hand, sulphide formation by D. piger was unaffected by E. hallii or A. caccae in these cocultures and tricultures. These experiments strongly suggest that lactate can stimulate sulphide formation by SRB present in the colon, with possible consequences for conditions such as colitis.

Sulphoxidation reaction catalysed by myeloperoxidase from human leucocytes.

PubMed

Capeillère-Blandin, C; Martin, C; Gaggero, N; Pasta, P; Carrea, G; Colonna, S

1998-10-01

The oxidation of alkyl aryl sulphides by myeloperoxidase (MPO) at the expense of hydrogen peroxide was investigated under steady-state conditions. The sulphide concentration effect was studied under saturating H2O2 concentrations at pH 5.0 and 20 degreesC. The kinetic constants, kcat and Km, of the different substrates were determined and the values were in the 1-10 s-1 range and around 43+/-26 microM respectively, whatever the sulphide considered. In the case of p-substituted thioanisoles, the oxidation rate was dependent upon the substituent effect. The correlation of log(kcat) with the substituent constants (sigma+ values) (Hammett equation) could be explained by a reaction mechanism involving the enzyme compound II and a sulphenium radical cation. This conclusion was also supported by spectrophotometric analysis of catalytic intermediates of the enzyme, showing the accumulation of compound II. Moreover, chiral HPLC analyses showed that MPO oxidation of alkyl aryl sulphides produced the corresponding (R)-sulphoxides with a low enantioselectivity (4-8%). Chloride ion effects on the MPO-catalysed oxygenation of sulphides were also studied. Chloride acted as a substrate for MPO and as an activator in MPO-catalysed sulphoxidation. Inhibition occurred at chloride concentrations above 120 mM, whereas below 120 mM, chloride increased the reaction rate when using p-tolyl methyl sulphide as the substrate. In the presence of 100 mM chloride the catalytic efficiency (kcat/Km) of MPO increased 3-4-fold, whatever the sulphide considered, but racemic products were obtained. These data have been interpreted in the light of known structural information on the accessibility of the distal haem cavity.

Lead sulphide: Low cost, abundant thermoelectrics

NASA Astrophysics Data System (ADS)

Ahmad, Sajid; Singh, Ajay; Bhattacharya, Shovit; Basu, Ranita; Bhatt, Ranu; Bohra, Anil; Muthe, K. P.; Gadkari, S. C.

2018-04-01

Lead and sulphur are the most abundant and low cost materials on the earth's crust, lead chalcogenide (S, Se and Te) materials have got best applications in thermoelectric power generations. Among the chalcogenides, selenium and tellurium are costlier and are more toxic material than sulphur. [1][2] Decreasing the thermal conductivity has been proven to be the easiest approach to improve the thermoelectric performance of a material. In the present work, the lead sulphide (PbS) and SrxPb(1-x)S composite materials were synthesized and investigated. Addition of 0.4 and 0.8 moles of Sr atoms into the PbS lattice has appreciably reduced the thermal conductivity from 2.2 W/mK to 0.43 W/mK for Sr0.4Pb0.6S composition. Temperature (T) dependence of thermoelectric (TE) properties PbS and and SrxPb(1-x)S nanocomposite material has been studied with in the temperature range of 300 K to 700 K. It is observed that there is reduction in the thermal conductivity of PbS alloy on addition of Sr that is mainly attributed to the scattering centres of Sr in the PbS matrix also the presence of the Sr also plays a role in the refinement of the PbS matrix.

Magneto-Optical Experiments on Rare Earth Garnet Films.

ERIC Educational Resources Information Center

Tanner, B. K.

1980-01-01

Describes experiments in which inexpensive or standard laboratory equipment is used to measure several macroscopic magnetic properties of thin rare earth garnet films used in the manufacture of magnetic bubble devices. (Author/CS)

Rare Earth Geochemistry of Rock Core form WY Reservoirs

DOE Data Explorer

Quillinan, Scott; Bagdonnas, Davin; McLaughlin, J. Fred; Nye, Charles

2016-10-01

These data include major, minor, trace and rare earth element concentration of geologic formations in Wyoming oil and gas fields. *Note - Link below contains updated version of spreadsheet (6/14/2017)

75 FR 25850 - Materials Strategy Request for Information

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-10

... (DOE) is seeking information from stakeholders on rare earth elements and other materials used in... strategic plan for addressing the role of rare earth elements and other materials in energy technologies and...

The Electronic Structure and Optical Properties of Anatase TiO₂ with Rare Earth Metal Dopants from First-Principles Calculations.

PubMed

Xie, Kefeng; Jia, Qiangqiang; Wang, Yizhe; Zhang, Wenxue; Xu, Jingcheng

2018-01-24

The electronic and optical properties of the rare earth metal atom-doped anatase TiO₂ have been investigated systematically via density functional theory calculations. The results show that TiO₂ doped by Ce or Pr is the optimal choice because of its small band gap and strong optical absorption. Rare earth metal atom doping induces several impurity states that tune the location of valence and conduction bands and an obvious lattice distortion that should reduce the probability of electron-hole recombination. This effect of band change originates from the 4 f electrons of the rare earth metal atoms, which leads to an improved visible light absorption. This finding indicates that the electronic structure of anatase TiO₂ is tuned by the introduction of impurity atoms.

The Electronic Structure and Optical Properties of Anatase TiO2 with Rare Earth Metal Dopants from First-Principles Calculations

PubMed Central

Xie, Kefeng; Jia, Qiangqiang; Wang, Yizhe; Zhang, Wenxue; Xu, Jingcheng

2018-01-01

The electronic and optical properties of the rare earth metal atom-doped anatase TiO2 have been investigated systematically via density functional theory calculations. The results show that TiO2 doped by Ce or Pr is the optimal choice because of its small band gap and strong optical absorption. Rare earth metal atom doping induces several impurity states that tune the location of valence and conduction bands and an obvious lattice distortion that should reduce the probability of electron–hole recombination. This effect of band change originates from the 4f electrons of the rare earth metal atoms, which leads to an improved visible light absorption. This finding indicates that the electronic structure of anatase TiO2 is tuned by the introduction of impurity atoms. PMID:29364161

Study on the light-color mixing of rare earth luminescent materials for anti-counterfeiting application

NASA Astrophysics Data System (ADS)

Zhang, Jishu; Zhang, Yingzi; Tao, Jin; Zhu, Yanan

2018-04-01

In order to find out the light color mixing mechanism of rare earth luminescent materials used in anti-counterfeiting fibers, we prepared three kinds of rare earth luminescent materials according to RGB tri-primary color, and mixed it together to form different mixtures in certain proportion. The phase structures of the luminescent material monomers were measured by x-ray diffractometer. The photochromic properties of the luminescent materials were tested and analyzed by fluorescence spectrophotometer. The results show that the light color mixing was consistent with the blending principle of additive color, but not the same because of the photochromic properties of rare earth luminescent materials, and we explored the reasons in the light wavelength and intensity. It was found that the enhancement of the luminescence intensity of the mixture on account of the superimposing of luminescence.

Refining and Mutual Separation of Rare Earths Using Biomass Wastes

NASA Astrophysics Data System (ADS)

Inoue, Katsutoshi; Alam, Shafiq

2013-10-01

Two different types of adsorption gels were prepared from biomass wastes. The first gel was produced from astringent persimmon peel rich in persimmon tannin, a polyphenol compound, which was prepared by means of simple dehydration condensation reaction using concentrated sulfuric acid for crosslinking. This adsorption gel was intended to be employed for the removal of radioactive elements, uranium (U(VI)) and thorium (Th(IV)), from rare earths. The second gel was prepared from chitosan, a basic polysaccharide, produced from shells of crustaceans such as crabs, shrimps, prawns, and other biomass wastes generated in marine product industry, by immobilizing functional groups of complexanes such as ethylendiaminetetraacetic acid and diethylentriaminepentaacetic acid (DTPA). This gel was developed for the mutual separation of rare earths. Of the two adsorption gels evaluated, the DTPA immobilized chitosan exhibited the most effective mutual separation among light rare earths.

METHOD OF PROCESSING MONAZITE SAND

DOEpatents

Welt, M.A.; Smutz, M.

1958-08-26

A process is described for recovering thorium, uranium, and rare earth values from monazite sand. The monazite sand is first digested with sulfuric acid and the resulting "monazite sulfate" solution is adjusted to a pH of between 0.4 and 3.0, and oxalate anions are added causing precipitation of the thorium and the rare earths as the oxalates. The oxalate precipitate is separated from the uranium containing supernatant solution, and is dried and calcined to the oxides. The thorium and rare earth oxides are then dissolved in nitric acid and the solution is contacted with tribntyl phosphate whereby an organic extract phase containing the cerium and thorium values is obtained, together with an aqueous raffinate containing the other rare earth values. The organic phase is then separated from the aqueous raffinate and the cerium and thorium are back extracted with an aqueous medium.

Composition of monazites from pegmatites in eastern Minas Gerais, Brazil

USGS Publications Warehouse

Murata, K.J.; Dutra, C.V.; da Costa, M.T.; Branco, J.J.R.

1959-01-01

Two zoned pegmatites in south-eastern Minas Gerais were sampled in detail for their content of monazite and xenotime and the monazite was analysed for certain of the rare-earth elements and thorium. The ratio of xenotime to monazite increases in both pegmatites from the wall toward the quartz core. The content of the less basic rare-earth elements and of thorium in monazite rises in the same direction. These variation trends suggest that during the crystallization of these pegmatites there was a fractionation of the elements leading to a more or less steady enrichment of the less basic rare-earth elements and of thorium in the residual fluids. One mode of explaining these observed effects postulates that the rare-earth elements and thorium were present in pegmatitic fluids as co-ordination complexes rather than as simple cations. ?? 1959.

Semiconductor sensor for optically measuring polarization rotation of optical wavefronts using rare earth iron garnets

DOEpatents

Duncan, Paul G.

2002-01-01

Described are the design of a rare earth iron garnet sensor element, optical methods of interrogating the sensor element, methods of coupling the optical sensor element to a waveguide, and an optical and electrical processing system for monitoring the polarization rotation of a linearly polarized wavefront undergoing external modulation due to magnetic field or electrical current fluctuation. The sensor element uses the Faraday effect, an intrinsic property of certain rare-earth iron garnet materials, to rotate the polarization state of light in the presence of a magnetic field. The sensor element may be coated with a thin-film mirror to effectively double the optical path length, providing twice the sensitivity for a given field strength or temperature change. A semiconductor sensor system using a rare earth iron garnet sensor element is described.

Preliminary reconnaissance survey for thorium, uranium, and rare-earth oxides, Bear Lodge Mountains, Crook County, Wyoming

USGS Publications Warehouse

Wilmarth, V.R.; Johnson, D.H.

1953-01-01

An area about 6 miles north of Sundance, in the Bear Lodge Mountains, in Crook County, Wyo., was examined during August 1950 for thorium, uranium, and rare-earth oxides and samples were collected. Uranium is known to occur in fluorite veins and iron-manganese veins and in the igneous rocks of Tertiary age that compose the core of the Bear Lodge Mountains. The uranium content of the samples ranges from 0.001 to 0.015 percent in those from the fluorite veins, from 0.005 to 0.018 percent in those from the iron-manganese veins, and from 0.001 to 0.017 percent in those from the igneous rocks. The radioactivity of the samples is more than that expected from the uranium content. Thorium accounts for most of this discrepancy. The thorium oxide content of samples ranges from 0.07 to 0.25 percent in those from the iron-manganese veins and from 0.07 to 0.39 percent in those from the sedimentary rocks, and from0.04 to 0.30 in those from the igneous rocks. Rare-earth oxides occur in iron-manganese veins and in zones of altered igneous rocks. The veins contain from 0.16 to 12.99 percent rare-earth oxides, and the igneous rocks, except for two localities, contain from 0.01 to 0.42 percent rare-earth oxides. Inclusions of metamorphosed sedimentary rocks in the intrusive rocks contain from 0.07 to 2.01 percent rare-earth oxides.

Luminescence properties of erbium doped sodium barium borate glass with silver nanoparticles

NASA Astrophysics Data System (ADS)

Rajeshree Patwari, D.; Eraiah, B.

2018-02-01

Alteration in the absorption features of rare earth (RE) doped glasses with silver nanoparticles is ever-challenging in photonics. Erbium (Er3+) doped glasses with composition (60-x-y)B2O3-30Na2CO3-10BaO-xEr2O3-yAgCl where (x=0.5, 1.0 and y=1.0 mol %) are synthesized using melt-quenching method. The density is determined by Archimedes principle and molar volumes are calculated. Glass samples were characterized by XRD and UV-Visible spectroscopy. UV-Visible spectra shows eleven prominent absorption peaks centred around 366, 378, 408, 442, 452, 489, 521, 547, 652, 800 and 977 nm equivalent to the rare earth (Er3+) ion transitions. The sample without rare earth shows no peaks which specifies that rare earth ion plays a spirited role in the glass matrix. The glass samples with silver and without rare earth ion shows plasmon peak on heat treatment. The energy band gap values calculated for direct and indirect transitions are in the range of 3.126-3.440eV and 2.58-3.177eV respectively. The refractive indices and Urbach energies are also determined. Photoluminescence spectra are recorded and studied for excitation of the most intense peaks of wavelengths 378 and 521nm. The luminescence of erbium ion is enhanced by the presence of silver when the concentration of rare earth ion is less than that of silver.

On the origin of life in the zinc world. 2. Validation of the hypothesis on the photosynthesizing zinc sulfide edifices as cradles of life on Earth.

PubMed

Mulkidjanian, Armen Y; Galperin, Michael Y

2009-08-24

The accompanying article (A.Y. Mulkidjanian, Biology Direct 4:26) puts forward a detailed hypothesis on the role of zinc sulfide (ZnS) in the origin of life on Earth. The hypothesis suggests that life emerged within compartmentalized, photosynthesizing ZnS formations of hydrothermal origin (the Zn world), assembled in sub-aerial settings on the surface of the primeval Earth. If life started within photosynthesizing ZnS compartments, it should have been able to evolve under the conditions of elevated levels of Zn2+ ions, byproducts of the ZnS-mediated photosynthesis. Therefore, the Zn world hypothesis leads to a set of testable predictions regarding the specific roles of Zn2+ ions in modern organisms, particularly in RNA and protein structures related to the procession of RNA and the "evolutionarily old" cellular functions. We checked these predictions using publicly available data and obtained evidence suggesting that the development of the primeval life forms up to the stage of the Last Universal Common Ancestor proceeded in zinc-rich settings. Testing of the hypothesis has revealed the possible supportive role of manganese sulfide in the primeval photosynthesis. In addition, we demonstrate the explanatory power of the Zn world concept by elucidating several points that so far remained without acceptable rationalization. In particular, this concept implies a new scenario for the separation of Bacteria and Archaea and the origin of Eukarya. The ability of the Zn world hypothesis to generate non-trivial veritable predictions and explain previously obscure items gives credence to its key postulate that the development of the first life forms started within zinc-rich formations of hydrothermal origin and was driven by solar UV irradiation. This concept implies that the geochemical conditions conducive to the origin of life may have persisted only as long as the atmospheric CO2 pressure remained above ca. 10 bar. This work envisions the first Earth biotopes as photosynthesizing and habitable areas of porous ZnS and MnS precipitates around primeval hot springs. Further work will be needed to provide details on the life within these communities and to elucidate the primordial (bio)chemical reactions. This article was reviewed by Arcady Mushegian, Eugene Koonin, and Patrick Forterre. For the full reviews, please go to the Reviewers' reports section.

On the origin of life in the Zinc world. 2. Validation of the hypothesis on the photosynthesizing zinc sulfide edifices as cradles of life on Earth

PubMed Central

Mulkidjanian, Armen Y; Galperin, Michael Y

2009-01-01

Background The accompanying article (A.Y. Mulkidjanian, Biology Direct 4:26) puts forward a detailed hypothesis on the role of zinc sulfide (ZnS) in the origin of life on Earth. The hypothesis suggests that life emerged within compartmentalized, photosynthesizing ZnS formations of hydrothermal origin (the Zn world), assembled in sub-aerial settings on the surface of the primeval Earth. Results If life started within photosynthesizing ZnS compartments, it should have been able to evolve under the conditions of elevated levels of Zn2+ ions, byproducts of the ZnS-mediated photosynthesis. Therefore, the Zn world hypothesis leads to a set of testable predictions regarding the specific roles of Zn2+ ions in modern organisms, particularly in RNA and protein structures related to the procession of RNA and the "evolutionarily old" cellular functions. We checked these predictions using publicly available data and obtained evidence suggesting that the development of the primeval life forms up to the stage of the Last Universal Common Ancestor proceeded in zinc-rich settings. Testing of the hypothesis has revealed the possible supportive role of manganese sulfide in the primeval photosynthesis. In addition, we demonstrate the explanatory power of the Zn world concept by elucidating several points that so far remained without acceptable rationalization. In particular, this concept implies a new scenario for the separation of Bacteria and Archaea and the origin of Eukarya. Conclusion The ability of the Zn world hypothesis to generate non-trivial veritable predictions and explain previously obscure items gives credence to its key postulate that the development of the first life forms started within zinc-rich formations of hydrothermal origin and was driven by solar UV irradiation. This concept implies that the geochemical conditions conducive to the origin of life may have persisted only as long as the atmospheric CO2 pressure remained above ca. 10 bar. This work envisions the first Earth biotopes as photosynthesizing and habitable areas of porous ZnS and MnS precipitates around primeval hot springs. Further work will be needed to provide details on the life within these communities and to elucidate the primordial (bio)chemical reactions. Reviewers This article was reviewed by Arcady Mushegian, Eugene Koonin, and Patrick Forterre. For the full reviews, please go to the Reviewers' reports section. PMID:19703275

Metal dispersion and mobility in soils from the Lik Zn-Pb-Ag massive sulphide deposit, NW Alaska: Environmental and exploration implications

USGS Publications Warehouse

Kelley, K.D.; Kelley, D.L.

2003-01-01

The Lik deposit in northern Alaska is a largely unexposed shale-hosted Zn-Pb-Ag massive sulphide deposit that is underlain by continuous permafrost. Residual soils overlying the mineralized zone have element enrichments that are two to six times greater than baseline values. The most prominent elements are Ag, Mo, P, Se, Sr, V by total 4-acid digestion and Tl by a weak partial digestion (Enzyme Leach or EL) because they show multi-point anomalies that extend across the entire mineralized zone, concentration ranges are 0.5-2.6 ppm Ag, 4-26 ppm Mo, 0.1-0.3% P, 3-22 ppm Se, 90-230 ppm Sr, 170-406 ppm V, and 1.6-30 ppb Tl. Lead, Sb, and Hg are also anomalous (up to 178 ppm, 30 ppm, and 1.9 ppm, respectively), but all are characterized by single point anomalies directly over the mineralized zone, with only slightly elevated concentrations over the lower mineralized section. Zinc (total) has a consistent baseline response of 200 ppm, but it is not elevated in soils overlying the mineralized zone. However, Zn by EL shows a distinct single-point anomaly over the ore zone that suggests it was highly mobile and partly adsorbed on oxides or other secondary phases during weathering. In situ analyses (by laser ablation ICP-MS) of pyrite and sphalerite from drill core suggest that sphalerite is the primary residence for Ag, Cd, and Hg in addition to Zn, and pyrite contains As, Fe, Sb, and Tl. The level and degree of oxidation, and the proportion of reacting pyrite and carbonate minerals are two factors that affected the mobility and transport of metals. In oxidizing conditions, Zn is highly mobile relative to Hg and Ag, perhaps explaining the decoupling of Zn from the other sphalerite-hosted elements in the soils. Soils are acidic (to 3.9 pH) directly over the deposit due to the presence of acid-producing pyrite, but acid-neutralizing carbonate away from the mineralized zone yield soils that are near neutral. The soils therefore formed in a complex system involving oxidation and weathering (mechanical and chemical) of sulphide minerals, dissolution of carbonate minerals, and precipitation of iron and manganese oxide minerals.

Interaction of mining activities and aquatic environment: A review from Greek mine sites.

NASA Astrophysics Data System (ADS)

Vasileiou, Eleni; Kallioras, Andreas

2016-04-01

In Greece a significant amount of mineral and ore deposits have been recorded accompanied by large industrial interest and a long mining history. Today many active and/or abandoned mine sites are scattered within the country; while mining activities take place in different sites for exploiting various deposits (clay, limestone, slate, gypsum, kaolin, mixed sulphide ores (lead, zinc, olivine, pozzolan, quartz lignite, nickel, magnesite, aluminum, bauxite, gold, marbles etc). The most prominent recent ones are: (i) the lignite exploitation that is extended in the area of Ptolemais (Western Macedonia) and Megalopolis (Central Peloponnese); and (ii) the major bauxite deposits located in central Greece within the Parnassos-Ghiona geotectonic zone and on Euboea Island. In the latter area, significant ores of magnesite were exploited and mixed sulphide ores. Centuries of intensive mining exploitation and metallurgical treatment of lead-silver deposits in Greece, have also resulted in significant abandoned sites, such as the one in Lavrion. Mining activities in Lavrio, were initiated in ancient times and continued until the 1980s, resulting in the production of significant waste stockpiles deposited in the area, crucial for the local water resources. Ιn many mining sites, environmental pressures are also recorded after the mine closure to the aquatic environment, as the surface waters flow through waste dump areas and contaminated soils. This paper aims to the geospatial visualization of the mining activities in Greece, in connection to their negative (surface- and/or ground-water pollution; overpumping due to extensive dewatering practices) or positive (enhanced groundwater recharge; pit lakes, improvement of water budget in the catchment scale) impacts on local water resources.

Measuring hypoxia induced metal release from highly contaminated estuarine sediments during a 40 day laboratory incubation experiment.

PubMed

Banks, Joanne L; Ross, D Jeff; Keough, Michael J; Eyre, Bradley D; Macleod, Catriona K

2012-03-15

Nutrient inputs to estuarine and coastal waters worldwide are increasing and this in turn is increasing the prevalence of eutrophication and hypoxic and anoxic episodes in these systems. Many urbanised estuaries are also subject to high levels of anthropogenic metal contamination. Environmental O(2) levels may influence whether sediments act as sinks or sources of metals. In this study we investigated the effect of an extended O(2) depletion event (40 days) on fluxes of trace metals (and the metalloid As) across the sediment-water interface in sediments from a highly metal contaminated estuary in S.E. Tasmania, Australia. We collected sediments from three sites that spanned a range of contamination and measured total metal concentration in the overlying water using sealed core incubations. Manganese and iron, which are known to regulate the release of other divalent cations from sub-oxic sediments, were released from sediments at all sites as hypoxia developed. In contrast, the release of arsenic, cadmium, copper and zinc was comparatively low, most likely due to inherent stability of these elements within the sediments, perhaps as a result of their refractory origin, their association with fine-grained sediments or their being bound in stable sulphide complexes. Metal release was not sustained due to the powerful effect of metal-sulphide precipitation of dissolved metals back into sediments. The limited mobilisation of sediment bound metals during hypoxia is encouraging, nevertheless the results highlight particular problems for management in areas where hypoxia might occur, such as the release of metals exacerbating already high loads or resulting in localised toxicity. Copyright © 2012 Elsevier B.V. All rights reserved.

Metals in the Scheldt estuary: From environmental concentrations to bioaccumulation.

PubMed

Van Ael, Evy; Blust, Ronny; Bervoets, Lieven

2017-09-01

To investigate the relationship between metal concentrations in abiotic compartments and in aquatic species, sediment, suspended matter and several aquatic species (Polychaeta, Oligochaeta, four crustacean species, three mollusc species and eight fish species) were collected during three seasons at six locations along the Scheldt estuary (the Netherlands-Belgium) and analysed on their metal content (Ag, Cd, Co, Cr, Cu, Ni, Pb, Zn and the metalloid As). Sediment and biota tissue concentrations were significantly influenced by sampling location, but not by season. Measurements of Acid Volatile Sulphides (AVS) concentrations in relation to Simultaneously Extracted Metals (SEM) in the sediment suggested that not all metals in the sediment will be bound to sulphides and some metals might be bioavailable. For all metals but zinc, highest concentrations were measured in invertebrate species; Ag and Ni in periwinkle, Cr, Co and Pb in Oligochaete worms and As, Cd and Cu in crabs and shrimp. Highest concentrations of Zn were measured in the kidney of European smelt. In fish, for most of the metals, the concentrations were highest in liver or kidney and lowest in muscle. For Zn however, highest concentrations were measured in the kidney of European smelt. For less than half of the metals significant correlations between sediment metal concentrations and bioaccumulated concentrations were found (liver/hepatopancreas or whole organism). To calculate the possible human health risk by consumption, average and maximum metal concentrations in the muscle tissues were compared to the minimum risk levels (MRLs). Concentrations of As led to the highest risk potential for all consumable species. Cadmium and Cu posed only a risk when consuming the highest contaminated shrimp and shore crabs. Consuming blue mussel could result in a risk for the metals As, Cd and Cr. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application of modified stir bar with nickel:zinc sulphide nanoparticles loaded on activated carbon as a sorbent for preconcentration of losartan and valsartan and their determination by high performance liquid chromatography.

PubMed

Pebdani, Arezou Amiri; Dadfarnia, Shayesteh; Shabani, Ali Mohammad Haji; Khodadoust, Saeid; Haghgoo, Soheila

2016-03-11

In this study, the stir bar was coated for the first time with the ​nicel:zins sulphide nanoparticles (Ni:ZnS NPs) loaded on activated carbon (AC) (Ni:ZnS-AC) as well as 1-ethyl-3-methylimidazolium hexafluorophosphate ionic liquid (IL) using sol gel technique and was used for stir bar sorptive extraction (SBSE) of losartan (LOS) and valsartan (VAL) as the model compounds. The extracted analytes were then quantified by high performance liquid chromatography (HPLC) equipped with an ultra violet detector. The best extraction performance for LOS and VAL was obtained through the optimization of the parameters affecting SBSE including pH of sample solution, ionic strength, extraction time, volume of desorption solvent, desorption time, and stirring speed. The fractional factorial design (FFD) was used to find the most important parameters, which were then optimized by the central composite design (CCD) and the desirability function (DF). Under the optimal experimental conditions, wide linear ranges of 0.4-50μgL(-1) and 0.5-50μgL(-1) and good RSDs (at level of 5μgL(-1) and n=6) of 4.4 and 4.9% were obtained for LOS and VAL, respectively. With the enrichment factors (EFs) of 188.6 and 184.8-fold, the limits of detection (LODs, S/N=3) of the developed method were found to be 0.12 and 0.15μgL(-1) for LOS and VAL, respectively. The developed method was successfully applied to the determination of LOS and VAL in urine and plasma matrices. Copyright © 2016 Elsevier B.V. All rights reserved.

Fractional crystallization, impregnation and sulphide saturation recorded in Mesozoic arc-related cumulates at King Mountain, Cache Creek Ophiolite, Northern British Columbia.

NASA Astrophysics Data System (ADS)

Bedard, J. H. J.; Zagorevski, A.; Corriveau, A. S.

2016-12-01

The Cache creek terrane extends from southern B.C. to the Yukon. It accreted to North America at 175Ma and is composed of Paleozoic seamounts, Mesozoic oceanic arcs and mantle rocks. Mantle harzburgite massifs represent intra-oceanic core-complexes. Mantle rocks are cut by gabbroic dykes and overlain by chert, lava, dismembered hypabyssal complexes and rare cumulates. At King Mountain, gabbronorites are in tectonic contact with subjacent peridotite. Other crustal relics exposed nearby include sheeted hypabyssal intrusions and volcanics that range from depleted arc tholeiites to boninites. The King Mountain cumulates are rhythmically layered, foliated gabbronorites with 5% oxides and minor interstitial hornblende that yields temperatures of 652-759oC. Cumulates may show evidence of compaction-related flattening and intra-cumulate shear (boudins, fold noses). A 300m thick continuous section records two fractional crystallization cycles, whole rock mg# varying from 60 to 35 in the 1st cycle and from 52 to 30 in the 2nd. Cumulates formed during passage of evolved multiply-saturated magmas derived from a deeper chamber towards the surface. Inverse trace element models show that the gabbronorite cumulates are compositionally akin to boninites. The lowest-mg# rocks in the differentiation cycles are rusty 10cm-1m interbeds with abundant magnetite+ ilmenite ( 10-15%), high sulphide contents ( 5-10%, pyrrhotite and chalcopyrite) and high V contents (<1200ppm). These are interpreted to record episodic co-accumulation of Fe-Ti-oxides, with the decrease in melt FeO-content triggering sulphide immiscibility. Hornblendite and hornblende tonalite veins are locally transposed into the layered cumulates, forming flaser gabbros with 5-50% cm-scale lensoid hornblendite that impregnates and replaces the foliated gabbro-norite; greatly increasing REE contents. Amphibole oikocrysts show evidence of internal deformation and record temperatures of 753-804 oC.

Phosphorus K-edge XANES spectroscopy of mineral standards

PubMed Central

Ingall, Ellery D.; Brandes, Jay A.; Diaz, Julia M.; de Jonge, Martin D.; Paterson, David; McNulty, Ian; Elliott, W. Crawford; Northrup, Paul

2011-01-01

Phosphorus K-edge X-ray absorption near-edge structure (XANES) spectroscopy was performed on phosphate mineral specimens including (a) twelve specimens from the apatite group covering a range of compositional variation and crystallinity; (b) six non-apatite calcium-rich phosphate minerals; (c) 15 aluminium-rich phosphate minerals; (d) ten phosphate minerals rich in either reduced iron or manganese; (e) four phosphate minerals rich in either oxidized iron or manganese; (f) eight phosphate minerals rich in either magnesium, copper, lead, zinc or rare-earth elements; and (g) four uranium phosphate minerals. The identity of all minerals examined in this study was independently confirmed using X-ray powder diffraction. Minerals were distinguished using XANES spectra with a combination of pre-edge features, edge position, peak shapes and post-edge features. Shared spectral features were observed in minerals with compositions dominated by the same specific cation. Analyses of apatite-group minerals indicate that XANES spectral patterns are not strongly affected by variations in composition and crystallinity typical of natural mineral specimens. PMID:21335905

Metal Recovery from Industrial Solid Waste — Contribution to Resource Sustainability

NASA Astrophysics Data System (ADS)

Yang, Yongxiang

Increased demand of metals has driven the accelerated mining and metallurgical production in recent years, causing fast depletion of primary metals resources. On the contrary, the mining and metallurgical industry generates large amount of solid residues and waste such as tailings, slags, flue dust and leach residues, with relative low valuable metal contents. On the other hand, end-of-life (EoL) consumer products form another significant resources. The current technology and processes for primary metals production are not readily applicable for direct metals extraction from these waste materials, and special adaptation and tailor-made processes are required. In the present paper, various solid waste resources are reviewed, and current technologies and R&D trends are discussed. The recent research at author's group is illustrated for providing potential solutions to future resource problems, including metal recovery from MSW incinerator bottom ashes, zinc recovery from industrial ashes and residues, and rare earth metals recovery from EoL permanent magnets.

A comparison of thermoelectric phenomena in diverse alloy systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, Bruce

1999-01-01

The study of thermoelectric phenomena in solids provides a wealth of opportunity for exploration of the complex interrelationships between structure, processing, and properties of materials. As thermoelectricity implies some type of coupled thermal and electrical behavior, it is expected that a basic understanding of transport behavior in materials is the goal of such a study. However, transport properties such as electrical resistivity and thermal diffusivity cannot be fully understood and interpreted without first developing an understanding of the material's preparation and its underlying structure. It is the objective of this dissertation to critically examine a number of diverse systems inmore » order to develop a broad perspective on how structure-processing-property relationships differ from system to system, and to discover the common parameters upon which any good thermoelectric material is based. The alloy systems examined in this work include silicon-germanium, zinc oxide, complex intermetallic compounds such as the half-Heusler MNiSn, where M = Ti, Zr, or Hf, and rare earth chalcogenides.« less

A divalent rare earth oxide semiconductor: Yttrium monoxide

NASA Astrophysics Data System (ADS)

Kaminaga, Kenichi; Sei, Ryosuke; Hayashi, Kouichi; Happo, Naohisa; Tajiri, Hiroo; Oka, Daichi; Fukumura, Tomoteru; Hasegawa, Tetsuya

Rare earth sesquioxides like Y2O3 are known as widegap insulators with the highly stable closed shell trivalent rare earth ions. On the other hand, rare earth monoxides such as YO have been recognized as gaseous phase, and only EuO and YbO were thermodynamically stable solid-phase rock salt monoxides. In this study, solid-phase rock salt yttrium monoxide, YO, was synthesized in a form of epitaxial thin film by pulsed laser deposition method. YO possesses unusual valence of Y2+ ([Kr] 4d1) . In contrast with Y2O3, YO was narrow gap semiconductor with dark-brown color. The electrical conductivity was tunable from 10-1 to 103 Ω-1 cm-1 by introducing oxygen vacancies as electron donor. Weak antilocalization behavior was observed indicating significant spin-orbit coupling owing to 4 d electron carrier. The absorption spectral shape implies the Mott-Hubbard insulator character of YO. Rare earth monoixdes will be new platform of functional oxides. This work was supported by JST-CREST, the Japan Society for the Promotion of Science (JSPS) with Grant-in-Aid for Scientific Research on Innovative Areas (Nos. 26105002 and 26105006), and Nanotechnology Platform (Project No.12024046) of MEXT, Japan.

A study on artificial rare earth (RE2O3) based neutron absorber.

PubMed

Kim, Kyung-O; Kyung Kim, Jong

2015-11-01

A new concept of a neutron absorption material (i.e., an artificial rare earth compound) was introduced for criticality control in a spent fuel storage system. In particular, spent nuclear fuels were considered as a potential source of rare earth elements because the nuclear fission of uranium produces a full range of nuclides. It was also found that an artificial rare earth compound (RE2O3) as a High-Level Waste (HLW) was naturally extracted from pyroprocessing technology developed for recovering uranium and transuranic elements (TRU) from spent fuels. In this study, various characteristics (e.g., activity, neutron absorption cross-section) were analyzed for validating the application possibility of this waste compound as a neutron absorption material. As a result, the artificial rare earth compound had a higher neutron absorption probability in the entire energy range, and it can be used for maintaining sub-criticality for more than 40 years on the basis of the neutron absorption capability of Boral™. Therefore, this approach is expected to vastly improve the efficiency of radioactive waste management by simultaneously keeping HLW and spent nuclear fuel in a restricted space. Copyright © 2015 Elsevier Ltd. All rights reserved.

A combined calorimetric and computational study of the energetics of rare earth substituted UO 2 systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Lei; Solomon, Jonathan M.; Asta, Mark

2015-09-01

The energetics of rare earth substituted UO2 solid solutions (U1-xLnxO2-0.5x+y, where Ln = La, Y, and Nd) are investigated employing a combination of calorimetric measurements and density functional theory based computations. Calculated and measured formation enthalpies agree within 10 kJ/mol for stoichiometric oxygen/metal compositions. To better understand the factors governing the stability and defect binding in rare earth substituted urania solid solutions, systematic trends in the energetics are investigated based on the present results and previous computational and experimental thermochemical studies of rare earth substituted fluorite oxides (A1-xLnxO2-0.5x, where A = Hf, Zr, Ce, and Th). A consistent trend towardsmore » increased energetic stability with larger size mismatch between the smaller host tetravalent cation and the larger rare earth trivalent cation is found for both actinide and non-actinide fluorite oxide systems where aliovalent substitution of Ln cations is compensated by oxygen vacancies. However, the large exothermic oxidation enthalpy in the UO2 based systems favors oxygen rich compositions where charge compensation occurs through the formation of uranium cations with higher oxidation states.« less

A novel methodology for rapid digestion of rare earth element ores and determination by microwave plasma-atomic emission spectrometry and dynamic reaction cell-inductively coupled plasma-mass spectrometry.

PubMed

Helmeczi, Erick; Wang, Yong; Brindle, Ian D

2016-11-01

Short-wavelength infrared radiation has been successfully applied to accelerate the acid digestion of refractory rare-earth ore samples. Determinations were achieved with microwave plasma-atomic emission spectrometry (MP-AES) and dynamic reaction cell - inductively coupled plasma-mass spectrometry (DRC-ICP-MS). The digestion method developed was able to tackle high iron-oxide and silicate matrices using only phosphoric acid in a time frame of only 8min, and did not require perchloric or hydrofluoric acid. Additionally, excellent recoveries and reproducibilities of the rare earth elements, as well as uranium and thorium, were achieved. Digestions of the certified reference materials OREAS-465 and REE-1, with radically different mineralogies, delivered results that mirror those obtained by fusion processes. For the rare-earth CRM OKA-2, whose REE data are provisional, experimental data for the rare-earth elements were generally higher than the provisional values, often exceeding z-values of +2. Determined values for Th and U in this reference material, for which certified values are available, were in excellent agreement. Copyright © 2016 Elsevier B.V. All rights reserved.

Effects of chemical and hydrostatic pressures on structural, magnetic, and electronic properties of R2NiMn O6 (R =rare -earth ion ) double perovskites

NASA Astrophysics Data System (ADS)

Zhao, Hong Jian; Liu, Xiao Qiang; Chen, Xiang Ming; Bellaiche, L.

2014-11-01

The effects of chemical and hydrostatic pressures on structural, magnetic, and electronic properties of R2NiMn O6 double perovskites, with R being a rare-earth ion, have been systematically studied by using specific first-principles calculations. These latter reproduce well the correlation between several properties (e.g., lattice parameters, Ni-O-Mn bond angles, magnetic Curie temperature, and electronic band gap) and the rare-earth ionic radius (i.e., the chemical pressure). They also provide novel predictions awaiting experimental confirmation, such as (i) that many physical quantities respond in dramatically different manners to chemical versus hydrostatic pressure, unlike as commonly thought for perovskites containing rare-earth ions, and (ii) a dependence of antipolar displacements on chemical and hydrostatic pressures, which would further explain why the recently predicted electrical polarization of L a2NiMn O6/R2NiMn O6 superlattices [H. J. Zhao, W. Ren, Y. Yang, J. Íñiguez, X. M. Chen, and L. Bellaiche, Nat. Commun. 5, 4021 (2014), 10.1038/ncomms5021] can be created and controlled by playing with the rare-earth element.

Adsorption Behavior of Rare Earth Metal Cations in the Interlayer Space of γ-ZrP.

PubMed

Takei, Takahiro; Iidzuka, Kiyoaki; Miura, Akira; Yanagida, Sayaka; Kumada, Nobuhiro; Magome, Eisuke; Moriyoshi, Chikako; Kuroiwa, Yoshihiro

2016-10-04

Adsorption competencies of rare earth metal cations in γ-zirconium phosphate were examined by ICP, synchrotron X-ray diffraction (SXRD), and ab initio simulation. The adsorption amounts are around 0.06-0.10 per zirconium phosphate. From the SXRD patterns of the adsorbed samples, the basal spacing estimated by c sin β increased linearly with an increasing ionic radius of rare earth metal cation, though a and b lattice constants show no change. These SXRD patterns can be classified into four groups that have different super lattices. The four superlattices have multiplicities of x131, x241, and x221 for the xabc axis, and the location of the rare earth metal cation in the original unit cell changes depending on the superlattice cell. In the x131 superlattice, Yb and Er occupied the site near the zirconium phosphate layer, though La and Ce in the x221 superlattice remained in the center position between the phosphate sheet. For the ab initio simulation of γ-ZrP with the typical rare earth metal cations (Tb, Eu, Dy, and La), the results of simulation show a similar tendency of the position estimated by SXRD refinements.

Effect of Solution Treatment on Microstructure and Properties of Gd - AZ91 Magnesium Alloy

NASA Astrophysics Data System (ADS)

Li, Yao; Wang, Huiling

2018-01-01

In this paper, the Gd-AZ91 alloy was manufactured by adding rare earth element Gd in AZ91 magnesium alloy. The effects of solution treatment on the microstructures of rare earth elements Gd were investigated by means of optical microscopy, scanning electron microscopy, X-ray diffraction analysis and equipment for testing mechanical properties. The experimental results show that the addition of rare earth element Gd in AZ91 magnesium alloy can refine the alloy grain, turn β-Mg17Al12 phase into a discontinuous network or point structure, and produce granular compound Al2Gd in the alloy; when solution temperature is about 380 °C, the alloy structure is the best, the tensile strength of the alloy is the largest with the value larger than 250Mpa; when the solution temperature exceeds 380 °C, the alloy structure is coarsened and the mechanical properties of the alloy are reduced. With the increase of rare earth element Gd content, the tensile strength of the alloy shows a tendency to increase gradually, which Indicates that the addition of a certain amount of rare earth elements Gd can improve the plasticity of the alloy.

Baiyun Ebo, China

NASA Image and Video Library

2012-04-11

Acquired by NASA Terra spacecraft, this image shows a mine in Baiyun Ebo, Inner Mongolia, China, the site of almost half the world rare earth production. China is responsible for over 95% of global production of rare earth elements.

Rare Earth Element Geochemistry for Produced Waters, WY

DOE Data Explorer

Quillinan, Scott; Nye, Charles; McLing, Travis; Neupane, Hari

2016-06-30

These data represent major, minor, trace, isotopes, and rare earth element concentrations in geologic formations and water associated with oil and gas production. *Note - Link below contains updated version of spreadsheet (6/14/2017)

The Tonian Beck Spring Dolomite: Marine dolomitization in a shallow, anoxic sea

NASA Astrophysics Data System (ADS)

Shuster, Alice Mary; Wallace, Malcolm William; van Smeerdijk Hood, Ashleigh; Jiang, Ganqing

2018-06-01

The reason for the abundance of dolomite lithologies in Earth's early geological record compared to modern environments remains contentious. This study provides new insight into this Precambrian "dolomite problem" by revisiting one of the most controversial dolomite localities, the Beck Spring Dolomite, of Death Valley, USA. Consistent with some previous studies, petrographic evidence indicates that although the Beck Spring Dolomite now consists almost entirely of dolomite, it was originally precipitated largely as aragonite and high-Mg calcite. Depositional constituents (microbialites and ooids) were likely originally aragonitic, and early marine length-fast cements (now dolomite) are suggested to have precipitated as high-Mg calcite then replaced syntaxially by dolomite. Based on petrographic and geochemical evidence, we suggest that marine dolomitization was the dominant synsedimentary diagenetic process in the unit, and for the most part, involved syntaxial and mimetic replacement. Further, a length-slow fibrous dolomite generation was precipitated during the later stages of marine diagenesis as a primary marine dolomite cement. This is indicated by the length-slow crystallographic structure of the cement and from its preserved geochemical and cathodoluminescence growth zonation. This new evidence for Tonian marine dolomite precipitation reinforces the idea of Precambrian marine environmental conditions, including the chemical composition of seawater, promoting dolomite formation at this time. The trace metal geochemical composition of well-preserved marine components, especially dolomite marine cements, reveals information about redox conditions in this Tonian shallow seawater. In terms of rare earth element geochemistry, the Beck Spring Dolomite has no significant Ce anomaly, and a ubiquitous positive Eu anomaly, consistent with widespread oceanic anoxia during deposition. Furthermore, the relatively low levels of iron and chalcophile elements Co, Cu, Pb and Zn in marine components compared to other Neoproterozoic carbonates suggest euxinic conditions (both anoxic and sulphidic) prevailed during deposition of the Beck Spring Dolomite.

Recovery of Rare Earths, Precious Metals and Other Critical Materials from Geothermal Waters with Advanced Sorbent Structures

DOE Data Explorer

Pamela M. Kinsey

2015-09-30

The work evaluates, develops and demonstrates flexible, scalable mineral extraction technology for geothermal brines based upon solid phase sorbent materials with a specific focus upon rare earth elements (REEs). The selected organic and inorganic sorbent materials demonstrated high performance for collection of trace REEs, precious and valuable metals. The nanostructured materials typically performed better than commercially available sorbents. Data contains organic and inorganic sorbent removal efficiency, Sharkey Hot Springs (Idaho) water chemsitry analysis, and rare earth removal efficiency from select sorbents.

Rare earth abundances and Rb-Sr systematics of basalts, gabbro, anorthosite and minor granitic rocks from the Indian Ocean Ridge System, Western Indian Ocean

USGS Publications Warehouse

Hedge, C.E.; Futa, K.; Engel, C.G.; Fisher, R.L.

1979-01-01

Basalts dredged from the Mid-Indian Ocean Ridge System have rare earth, Rb, and Sr concentrations like those from other mid-ocean ridges, but have slightly higher Sr87/Sr86 ratios. Underlying gabbroic complexes are similar to the basalts in Sr87/Sr86, but are poorer K, Rb, and in rare earths. The chemical and isotopic data, as well as the geologic relations suggest a cumulate origin for the bulk of the gabbroic complexes. ?? 1979 Springer-Verlag.

Rare earth-transition metal scrap treatment method

DOEpatents

Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.; Jones, Lawrence L.; Lincoln, Lanny P.

1992-02-11

Rare earth-transition metal (e.g. iron) scrap (e.g. Nd-Fe-B scrap) is melted to reduce the levels of tramp oxygen and nitrogen impurities therein. The tramp impurities are reduced in the melt by virtue of the reaction of the tramp impurities and the rare earth to form dross on the melt. The purified melt is separated from the dross for reuse. The oxygen and nitrogen of the melt are reduced to levels acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets.

Rare earth-transition metal scrap treatment method

DOEpatents

Schmidt, F.A.; Peterson, D.T.; Wheelock, J.T.; Jones, L.L.; Lincoln, L.P.

1992-02-11

Rare earth-transition metal (e.g. iron) scrap (e.g. Nd-Fe-B scrap) is melted to reduce the levels of tramp oxygen and nitrogen impurities therein. The tramp impurities are reduced in the melt by virtue of the reaction of the tramp impurities and the rare earth to form dross on the melt. The purified melt is separated from the dross for reuse. The oxygen and nitrogen of the melt are reduced to levels acceptable for reuse of the treated alloy in the manufacture of end-use articles, such as permanent magnets. 3 figs.

Electron traps in Gd3Ga3Al2O12:Ce garnets doped with rare-earth ions

NASA Astrophysics Data System (ADS)

Khanin, V. M.; Rodnyi, P. A.; Wieczorek, H.; Ronda, C. R.

2017-05-01

The curves of thermally stimulated luminescence of Gd3Ga3Al2O12:Ce3+ ceramics (a nominally pure sample and samples doped with rare-earth ions) are measured in the temperature range of 80-550 K. The depth and the frequency factor of electron traps established by Eu and Yb impurities are determined. An energy-level diagram of rare-earth ions in the bandgap of Gd3Ga3Al2O12 is presented.

Thermophysical properties of liquid rare earth metals

NASA Astrophysics Data System (ADS)

Thakor, P. B.; Sonvane, Y. A.; Patel, H. P.; Jani, A. R.

2013-06-01

The thermodynamical properties like long wavelength limit S(0), iso-thermal compressibility (χT), thermal expansion coefficient (αV), thermal pressure coefficient (γV), specific heat at constant volume (CV) and specific heat at constant pressure (CP) are calculated for liquid rare earth metals. Our newly constructed parameter free model potential is used to describe the electron ion interaction due to Sarkar et al (S) local field correction function. Lastly, we conclude that our newly constructed model potential is capable to explain the thermophysical properties of liquid rare earth metals.