pH-zone-refining elution-extrusion countercurrent chromatography: Separation of hydroxyanthraquinones from Cassiae semen.

PubMed

Bu, Zhisi; Lv, Liqiong; Li, Xingnuo; Chu, Chu; Tong, Shengqiang

2017-11-01

Seven hydroxyanthraquinones were successfully separated from the traditional Chinese medicinal herb Cassiae semen by conventional and pH-zone-refining countercurrent chromatography with an environmentally friendly biphasic solvent system, in which elution-extrusion mode was investigated for pH-zone-refining countercurrent chromatography for the first time. A two-phase solvent system composed of n-hexane/ethyl acetate/ethanol/water (5:3:4:4, v/v/v/v) was used for the conventional countercurrent chromatography while the same system with a different volume ratio n-hexane/ethyl acetate/ethanol/water (3:5:2:6, v/v/v/v) was used for pH-zone-refining countercurrent chromatography, in which 20 mmol/L of trifluoroacetic acid was added in the organic phase as a retainer and 15 mmol/L of ammonia was added to the aqueous phase as an eluter. A 400 mg crude sample could be well separated by pH-zone-refining countercurrent chromatography, yielding 53 mg of aurantio-obtusin, 40 mg of chryso-obtusin, 18 mg of obtusin, 24 mg of obtusifolin, 10 mg of emodin, and 105 mg of the mixture of chrysophanol and physcion with a purity of over 95.8, 95.7, 96.9, 93.5, 97.4, 77.1, and 19.8%, as determined by high-performance liquid chromatography. Furthermore, the difference in elution sequence between conventional and pH-zone-refining mode was observed and discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Viable Scheme for Elemental Extraction and Purification Using In-Situ Planetary Resources

NASA Technical Reports Server (NTRS)

Sen, S.; Schofield, E.; ODell, S.; Ray, C. S.

2005-01-01

NASA's new strategic direction includes establishing a self-sufficient, affordable and safe human and robotic presence outside the low earth orbit. Some of the items required for a self-sufficient extra-terrestrial habitat will include materials for power generation (e.g. Si for solar cells) and habitat construction (e.g. Al, Fe, and Ti). In this paper we will present a viable elemental extraction and refining process from in-situ regolith which would be optimally continuous, robotically automated, and require a minimum amount of astronaut supervision and containment facilities, The approach is based on using a concentrated heat source and translating sample geometry to enable simultaneous oxide reduction and elemental refining. Preliminary results will be presented to demonstrate that the proposed zone refining process is capable of segregating or refining important elements such as Si (for solar cell fabrication) and Fe (for habitat construction). A conceptual scheme will be presented whereby such a process could be supported by use of solar energy and a precursor robotic mission on the surface of the moon.

The Mechanism of Ultrasonic Vibration on Grain Refining and Degassing in GTA Spot Welding of Copper Joints.

PubMed

Al-Ezzi, Salih; Quan, Gaofeng; Elrayah, Adil

2018-05-07

This paper examines the effect of ultrasonic vibration (USV) on grain size and interrupted porosity in Gas Tungsten Arc (GTA) spot-welded copper. Grain size was refined by perpendicularly attaching a transducer to the welded sheet and applying USV to the weld pool for a short time (0, 2, 4, and 6 s) in addition improvements to the degassing process. Results illustrate a significant reduction of grain size (57%). Notably, USV provided interaction between reformations (fragmentation) and provided nucleation points (detaching particles from the fusion line) for grains in the nugget zone and the elimination of porosity in the nugget zone. The GTA spot welding process, in conjunction with USV, demonstrated an improvement in the corrosion potential for a copper spot-welded joint in comparison to the joint welded without assistance of USV. Finally, welding of copper by GTA spot welding in conjunction with ultrasound for 2 s presented significant mechanical properties.

The Mechanism of Ultrasonic Vibration on Grain Refining and Degassing in GTA Spot Welding of Copper Joints

PubMed Central

Quan, Gaofeng

2018-01-01

This paper examines the effect of ultrasonic vibration (USV) on grain size and interrupted porosity in Gas Tungsten Arc (GTA) spot-welded copper. Grain size was refined by perpendicularly attaching a transducer to the welded sheet and applying USV to the weld pool for a short time (0, 2, 4, and 6 s) in addition improvements to the degassing process. Results illustrate a significant reduction of grain size (57%). Notably, USV provided interaction between reformations (fragmentation) and provided nucleation points (detaching particles from the fusion line) for grains in the nugget zone and the elimination of porosity in the nugget zone. The GTA spot welding process, in conjunction with USV, demonstrated an improvement in the corrosion potential for a copper spot-welded joint in comparison to the joint welded without assistance of USV. Finally, welding of copper by GTA spot welding in conjunction with ultrasound for 2 s presented significant mechanical properties. PMID:29735894

Succinonitrile Purification Facility

NASA Technical Reports Server (NTRS)

2003-01-01

The Succinonitrile (SCN) Purification Facility provides succinonitrile and succinonitrile alloys to several NRA selected investigations for flight and ground research at various levels of purity. The purification process employed includes both distillation and zone refining. Once the appropriate purification process is completed, samples are characterized to determine the liquidus and/or solidus temperature, which is then related to sample purity. The lab has various methods for measuring these temperatures with accuracies in the milliKelvin to tenths of milliKelvin range. The ultra-pure SCN produced in our facility is indistinguishable from the standard material provided by NIST to well within the stated +/- 1.5mK of the NIST triple point cells. In addition to delivering material to various investigations, our current activities include process improvement, characterization of impurities and triple point cell design and development. The purification process is being evaluated for each of the four vendors to determine the efficacy of each purification step. We are also collecting samples of the remainder from distillation and zone refining for analysis of the constituent impurities. The large triple point cells developed will contain SCN with a melting point of 58.0642 C +/- 1.5mK for use as a calibration standard for Standard Platinum Resistance Thermometers (SPRTs).

Laser furnace and method for zone refining of semiconductor wafers

NASA Technical Reports Server (NTRS)

Griner, Donald B. (Inventor); zur Burg, Frederick W. (Inventor); Penn, Wayne M. (Inventor)

1988-01-01

A method of zone refining a crystal wafer (116 FIG. 1) comprising the steps of focusing a laser beam to a small spot (120) of selectable size on the surface of the crystal wafer (116) to melt a spot on the crystal wafer, scanning the small laser beam spot back and forth across the surface of the crystal wafer (116) at a constant velocity, and moving the scanning laser beam across a predetermined zone of the surface of the crystal wafer (116) in a direction normal to the laser beam scanning direction and at a selectible velocity to melt and refine the entire crystal wafer (116).

Improved hydrocracker temperature control: Mobil quench zone technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarli, M.S.; McGovern, S.J.; Lewis, D.W.

1993-01-01

Hydrocracking is a well established process in the oil refining industry. There are over 2.7 million barrels of installed capacity world-wide. The hydrocracking process comprises several families of highly exothermic reactions and the total adiabatic temperature rise can easily exceed 200 F. Reactor temperature control is therefore very important. Hydrocracking reactors are typically constructed with multiple catalyst beds in series. Cold recycle gas is usually injected between the catalyst beds to quench the reactions, thereby controlling overall temperature rise. The design of this quench zone is the key to good reactor temperature control, particularly when processing poorer quality, i.e., highermore » heat release, feeds. Mobil Research and Development Corporation (MRDC) has developed a robust and very effective quench zone technology (QZT) package, which is now being licensed to the industry for hydrocracking applications.« less

Ductility Improvement of an AZ61 Magnesium Alloy through Two-Pass Submerged Friction Stir Processing

PubMed Central

Luo, Xicai; Cao, Genghua; Zhang, Wen; Qiu, Cheng; Zhang, Datong

2017-01-01

Friction stir processing (FSP) has been considered as a novel technique to refine the grain size and homogenize the microstructure of metallic materials. In this study, two-pass FSP was conducted under water to enhance the cooling rate during processing, and an AZ61 magnesium alloy with fine-grained and homogeneous microstructure was prepared through this method. Compared to the as-cast material, one-pass FSP resulted in grain refinement and the β-Mg17Al12 phase was broken into small particles. Using a smaller stirring tool and an overlapping ratio of 100%, a finer and more uniform microstructure with an average grain size of 4.6 μm was obtained through two-pass FSP. The two-pass FSP resulted in a significant improvement in elongation of 37.2% ± 4.3%, but a slight decrease in strength compared with one-pass FSP alloy. Besides the microstructure refinement, the texture evolution in the stir zone is also considered responsible for the ductility improvement. PMID:28772614

Automatic detection and classification of damage zone(s) for incorporating in digital image correlation technique

NASA Astrophysics Data System (ADS)

Bhattacharjee, Sudipta; Deb, Debasis

2016-07-01

Digital image correlation (DIC) is a technique developed for monitoring surface deformation/displacement of an object under loading conditions. This method is further refined to make it capable of handling discontinuities on the surface of the sample. A damage zone is referred to a surface area fractured and opened in due course of loading. In this study, an algorithm is presented to automatically detect multiple damage zones in deformed image. The algorithm identifies the pixels located inside these zones and eliminate them from FEM-DIC processes. The proposed algorithm is successfully implemented on several damaged samples to estimate displacement fields of an object under loading conditions. This study shows that displacement fields represent the damage conditions reasonably well as compared to regular FEM-DIC technique without considering the damage zones.

Modeling unsaturated zone flow and runoff processes by integrating MODFLOW-LGR and VSF, and creating the new CFL package

USGS Publications Warehouse

Borsia, I.; Rossetto, R.; Schifani, C.; Hill, Mary C.

2013-01-01

In this paper two modifications to the MODFLOW code are presented. One concerns an extension of Local Grid Refinement (LGR) to Variable Saturated Flow process (VSF) capability. This modification allows the user to solve the 3D Richards’ equation only in selected parts of the model domain. The second modification introduces a new package, named CFL (Cascading Flow), which improves the computation of overland flow when ground surface saturation is simulated using either VSF or the Unsaturated Zone Flow (UZF) package. The modeling concepts are presented and demonstrated. Programmer documentation is included in appendices.

Simulation in Metallurgical Processing: Recent Developments and Future Perspectives

NASA Astrophysics Data System (ADS)

Ludwig, Andreas; Wu, Menghuai; Kharicha, Abdellah

2016-08-01

This article briefly addresses the most important topics concerning numerical simulation of metallurgical processes, namely, multiphase issues (particle and bubble motion and flotation/sedimentation of equiaxed crystals during solidification), multiphysics issues (electromagnetic stirring, electro-slag remelting, Cu-electro-refining, fluid-structure interaction, and mushy zone deformation), process simulations on graphical processing units, integrated computational materials engineering, and automatic optimization via simulation. The present state-of-the-art as well as requirements for future developments are presented and briefly discussed.

An Adaptive Mesh Algorithm: Mesh Structure and Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scannapieco, Anthony J.

2016-06-21

The purpose of Adaptive Mesh Refinement is to minimize spatial errors over the computational space not to minimize the number of computational elements. The additional result of the technique is that it may reduce the number of computational elements needed to retain a given level of spatial accuracy. Adaptive mesh refinement is a computational technique used to dynamically select, over a region of space, a set of computational elements designed to minimize spatial error in the computational model of a physical process. The fundamental idea is to increase the mesh resolution in regions where the physical variables are represented bymore » a broad spectrum of modes in k-space, hence increasing the effective global spectral coverage of those physical variables. In addition, the selection of the spatially distributed elements is done dynamically by cyclically adjusting the mesh to follow the spectral evolution of the system. Over the years three types of AMR schemes have evolved; block, patch and locally refined AMR. In block and patch AMR logical blocks of various grid sizes are overlaid to span the physical space of interest, whereas in locally refined AMR no logical blocks are employed but locally nested mesh levels are used to span the physical space. The distinction between block and patch AMR is that in block AMR the original blocks refine and coarsen entirely in time, whereas in patch AMR the patches change location and zone size with time. The type of AMR described herein is a locally refi ned AMR. In the algorithm described, at any point in physical space only one zone exists at whatever level of mesh that is appropriate for that physical location. The dynamic creation of a locally refi ned computational mesh is made practical by a judicious selection of mesh rules. With these rules the mesh is evolved via a mesh potential designed to concentrate the nest mesh in regions where the physics is modally dense, and coarsen zones in regions where the physics is modally sparse.« less

Microstructure characterization of the stir zone of submerged friction stir processed aluminum alloy 2219

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Xiuli, E-mail: feng.97@osu.edu; State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001; Liu, Huijie, E-mail: liuhj@hit.edu.cn

Aluminum alloy 2219-T6 was friction stir processed using a novel submerged processing technique to facilitate cooling. Processing was conducted at a constant tool traverse speed of 200 mm/min and spindle rotation speeds in the range from 600 to 800 rpm. The microstructural characteristics of the base metal and processed zone, including grain structure and precipitation behavior, were studied using optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Microhardness maps were constructed on polished cross sections of as-processed samples. The effect of tool rotation speed on the microstructure and hardness of the stir zone was investigated. Themore » average grain size of the stir zone was much smaller than that of the base metal, but the hardness was also lower due to the formation of equilibrium θ precipitates from the base metal θ′ precipitates. Stir zone hardness was found to decrease with increasing rotation speed (heat input). The effect of processing conditions on strength (hardness) was rationalized based on the competition between grain refinement strengthening and softening due to precipitate overaging. - Highlights: • SZ grain size (∼ 1 μm) is reduced by over one order of magnitude relative to the BM. • Hardness in the SZ is lower than that of the precipitation strengthened BM. • Metastable θ′ in the base metal transforms to equilibrium θ in the stir zone. • Softening in the SZ results from a decrease of precipitation strengthening.« less

Thermal modeling of grinding for process optimization and durability improvements

NASA Astrophysics Data System (ADS)

Hanna, Ihab M.

Both thermal and mechanical aspects of the grinding process are investigated in detail in an effort to predict grinding induced residual stresses. An existing thermal model is used as a foundation for computing heat partitions and temperatures in surface grinding. By numerically processing data from IR temperature measurements of the grinding zone; characterizations are made of the grinding zone heat flux. It is concluded that the typical heat flux profile in the grinding zone is triangular in shape, supporting this often used assumption found in the literature. Further analyses of the computed heat flux profiles has revealed that actual grinding zone contact lengths exceed geometric contact lengths by an average of 57% for the cases considered. By integrating the resulting heat flux profiles; workpiece energy partitions are computed for several cases of dry conventional grinding of hardened steel. The average workpiece energy partition for the cases considered was 37%. In an effort to more accurately predict grinding zone temperatures and heat fluxes, refinements are made to the existing thermal model. These include consideration of contact length extensions due to local elastic deformations, variations of the assumed contact area ratio as a function of grinding process parameters, consideration of coolant latent heat of vaporization and its effect on heat transfer beyond the coolant boiling point, and incorporation of coolant-workpiece convective heat flux effects outside the grinding zone. The result of the model refinements accounting for contact length extensions and process-dependant contact area ratios is excellent agreement with IR temperature measurements over a wide range of grinding conditions. By accounting for latent heat of vaporization effects, grinding zone temperature profiles are shown to be capable of reproducing measured profiles found in the literature for cases on the verge of thermal surge conditions. Computed peak grinding zone temperatures for the aggressive grinding examples given are 30--50% lower than those computed using the existing thermal model formulation. By accounting for convective heat transfer effects outside the grinding zone, it is shown that while surface temperatures in the wake of the grinding zone may be significantly affected under highly convective conditions, computed residual stresses are less sensitive to such conditions. Numerical models are used to evaluate both thermally and mechanically induced stress fields in an elastic workpiece, while finite element modeling is used to evaluate residual stresses for workpieces with elastic-plastic material properties. Modeling of mechanical interactions at the local grit-workpiece length scale is used to create the often measured effect of compressive surface residual stress followed by a subsurface tensile peak. The model is shown to be capable of reproducing trends found in the literature of surface residual stresses which are compressive for low temperature grinding conditions, with surface stresses increasing linearly and becoming tensile with increasing temperatures. Further modifications to the finite element model are made to allow for transiently varying inputs for more complicated grinding processes of industrial components such as automotive cam lobes.

Microstructure and Crystallographic Texture Evolution During the Friction-Stir Processing of a Precipitation-Hardenable Aluminum Alloy

NASA Astrophysics Data System (ADS)

Nadammal, Naresh; Kailas, Satish V.; Szpunar, Jerzy; Suwas, Satyam

2015-05-01

Friction-stir processing (FSP) has been proven as a successful method for the grain refinement of high-strength aluminum alloys. The most important attributes of this process are the fine-grain microstructure and characteristic texture, which impart suitable properties in the as-processed material. In the current work, FSP of the precipitation-hardenable aluminum alloy 2219 has been carried out and the consequent evolution of microstructure and texture has been studied. The as-processed materials were characterized using electron back-scattered diffraction, x-ray diffraction, and electron probe microanalysis. Onion-ring formation was observed in the nugget zone, which has been found to be related to the precipitation response and crystallographic texture of the alloy. Texture development in the alloy has been attributed to the combined effect of shear deformation and dynamic recrystallization. The texture was found heterogeneous even within the nugget zone. A microtexture analysis revealed the dominance of shear texture components, with C component at the top of nugget zone and the B and A2* components in the middle and bottom. The bulk texture measurement in the nugget zone revealed a dominant C component. The development of a weaker texture along with the presence of some large particles in the nugget zone indicates particle-stimulated nucleation as the dominant nucleation mechanism during FSP. Grain growth follows the Burke and Turnbull mechanism and geometrical coalescence.

Purification of HgI.sub.2 for nuclear detector fabrication

DOEpatents

Schieber, Michael M.

1978-01-01

A process for purification of mercuric iodide (HgI.sub.2) to be used as a source material for the growth of detector quality crystals. The high purity HgI.sub.2 raw material is produced by a combination of three stages: synthesis of HgI.sub.2 from Hg and I.sub.2, repeated sublimation, and zone refining.

Processing of Lunar Soil Simulant for Space Exploration Applications

NASA Technical Reports Server (NTRS)

Sen, Subhayu; Ray, Chandra S.; Reddy, Ramana

2005-01-01

NASA's long-term vision for space exploration includes developing human habitats and conducting scientific investigations on planetary bodies, especially on Moon and Mars. To reduce the level of up-mass processing and utilization of planetary in-situ resources is recognized as an important element of this vision. Within this scope and context, we have undertaken a general effort aimed primarily at extracting and refining metals, developing glass, glass-ceramic, or traditional ceramic type materials using lunar soil simulants. In this paper we will present preliminary results on our effort on carbothermal reduction of oxides for elemental extraction and zone refining for obtaining high purity metals. In additions we will demonstrate the possibility of developing glasses from lunar soil simulant for fixing nuclear waste from potential nuclear power generators on planetary bodies. Compositional analysis, x-ray diffraction patterns and differential thermal analysis of processed samples will be presented.

Morphological ripening of fluid inclusions and coupled zone-refining in quartz crystals revealed by cathodoluminescence imaging: Implications for CL-petrography, fluid inclusion analysis and trace-element geothermometry

NASA Astrophysics Data System (ADS)

Lambrecht, Glenn; Diamond, Larryn William

2014-09-01

Cathodoluminescence (CL) studies have previously shown that some secondary fluid inclusions in luminescent quartz are surrounded by dark, non-luminescent patches, resulting from fracture-sealing by late, trace-element-poor quartz. This finding has led to the tacit generalization that all dark CL patches indicate influx of low temperature, late-stage fluids. In this study we have examined natural and synthetic hydrothermal quartz crystals using CL imaging supplemented by in-situ elemental analysis. The results lead us to propose that all natural, liquid-water-bearing inclusions in quartz, whether trapped on former crystal growth surfaces (i.e., of primary origin) or in healed fractures (i.e., of pseudosecondary or secondary origin), are surrounded by three-dimensional, non-luminescent patches. Cross-cutting relations show that the patches form after entrapment of the fluid inclusions and therefore they are not diagnostic of the timing of fluid entrapment. Instead, the dark patches reveal the mechanism by which fluid inclusions spontaneously approach morphological equilibrium and purify their host quartz over geological time. Fluid inclusions that contain solvent water perpetually dissolve and reprecipitate their walls, gradually adopting low-energy euhedral and equant shapes. Defects in the host quartz constitute solubility gradients that drive physical migration of the inclusions over distances of tens of μm (commonly) up to several mm (rarely). Inclusions thus sequester from their walls any trace elements (e.g., Li, Al, Na, Ti) present in excess of equilibrium concentrations, thereby chemically purifying their host crystals in a process analogous to industrial zone refining. Non-luminescent patches of quartz are left in their wake. Fluid inclusions that contain no liquid water as solvent (e.g., inclusions of low-density H2O vapor or other non-aqueous volatiles) do not undergo this process and therefore do not migrate, do not modify their shapes with time, and are not associated with dark-CL zone-refined patches. This new understanding has implications for the interpretation of solids within fluid inclusions (e.g., Ti- and Al-minerals) and for the elemental analysis of hydrothermal and metamorphic quartz and its fluid inclusions by microbeam methods such as LA-ICPMS and SIMS. As Ti is a common trace element in quartz, its sequestration by fluid inclusions and its depletion in zone-refined patches impacts on applications of the Ti-in-quartz geothermometer.

Preparative separation of six rhynchophylla alkaloids from Uncaria macrophylla wall by pH-zone refining counter-current chromatography.

PubMed

Zhang, Qinghai; Lin, Changhu; Duan, Wenjuan; Wang, Xiao; Luo, Aiqin

2013-12-12

pH-Zone refining counter-current chromatography was successfully applied to the preparative isolation and purification of six alkaloids from the ethanol extracts of Uncaria macrophylla Wall. Because of the low content of alkaloids (about 0.2%, w/w) in U. macrophylla Wall, the target compounds were enriched by pH-zone refining counter-current chromatography using a two-phase solvent system composed of petroleum ether-ethyl acetate-isopropanol-water (2:6:3:9, v/v), adding 10 mM triethylamine in organic stationary phase and 5 mM hydrochloric acid in aqueous mobile phase. Then pH-zone refining counter-current chromatography using the other two-phase solvent system was used for final purification. Six target compounds were finally isolated and purified by following two-phase solvent system composed of methyl tert-butyl ether (MTBE)-acetonitrile-water (4:0.5:5, v/v), adding triethylamine (TEA) (10 mM) to the organic phase and HCl (5 mM) to aqueous mobile phase. The separation of 2.8 g enriched total alkaloids yielded 36 mg hirsutine, 48 mg hirsuteine, 82 mg uncarine C, 73 mg uncarine E, 163 mg rhynchophylline, and 149 mg corynoxeine, all with purities above 96% as verified by HPLC Their structures were identified by electrospray ionization-mass spectrometry (ESI-MS) and 1H-NMR spectroscopy.

Characterization of ultra-fine grained aluminum produced by accumulative back extrusion (ABE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alihosseini, H., E-mail: hamid.alihossieni@gmail.com; Materials Science and Engineering Department, Engineering School, Amirkabir University, Tehran; Faraji, G.

2012-06-15

In the present work, the microstructural evolutions and microhardness of AA1050 subjected to one, two and three passes of accumulative back extrusion (ABE) were investigated. The microstructural evolutions were characterized using transmission electron microscopy. The results revealed that applying three passes of accumulative back extrusion led to significant grain refinement. The initial grain size of 47 {mu}m was refined to the grains of 500 nm after three passes of ABE. Increasing the number of passes resulted in more decrease in grain size, better microstructure homogeneity and increase in the microhardness. The cross-section of ABEed specimen consisted of two different zones:more » (i) shear deformation zone, and (ii) normal deformation zone. The microhardness measurements indicated that the hardness increased from the initial value of 31 Hv to 67 Hv, verifying the significant microstructural refinement via accumulative back extrusion. - Highlights: Black-Right-Pointing-Pointer A significant grain refinement can be achieved in AA1050, Al alloy by applying ABE. Black-Right-Pointing-Pointer Microstructural homogeneity of ABEed samples increased by increasing the number of ABE cycles. Black-Right-Pointing-Pointer A substantial increase in the hardness, from 31 Hv to 67 Hv, was recorded.« less

Novel Materials and Devices from Self-Assembled Periodic Structures

DTIC Science & Technology

1994-09-30

front works almost in a zone refining. 4 The most outstanding adiement of the praent work is that the developmnut of hydrogel membranes consisting of...dosely packed interconnected micr es of PNIAAm. These membranes are prepared by drying out the colloidal dispersions. These membranes exhibit reversible...volume changes in aqueous medium with temperature. We hope these will function as temperature sensitive diffraction membranes . We are in the process of

Effect of zirconium addition on welding of aluminum grain refined by titanium plus boron

NASA Astrophysics Data System (ADS)

Zaid, A. I. O.

2014-06-01

Aluminum oxidizes freely in ordinary atmosphere which makes its welding difficult and weak, particularly it solidifies in columnar structure with large grains. Therefore, it is anticipated that the effect of addition of some grain refiners to its melt before solidification is worth while investigating as it may enhance its weldabilty and improve its mechanical strength. In this paper, the effect of addition of zirconium at a weight of 0.1% (which corresponds to the peretictic limit on the aluminum-zirconium base phase diagram) to commercially pure aluminum, grain refined by Ti+B on its weldability, using gas tungsten arc welding, GTAW, method which was formerly known as TIG. A constant current level of 30 AC Ampere was used because it removes the oxides during the welding process. Metallographic examination of the weldments of the different combinations of Al with Al and Al with its microalloys: in the heat affected zone, HAZ, and away from it was carried out and examined for HAZ width, porosity, cracks and microhardness. It was found that grain refining by Ti+B or Zr resulted in enhancement of the weldment.

New biphasic solvent system based on cyclopentyl methyl ether for the purification of a non-polar synthetic peptide by pH-zone refining centrifugal partition chromatography.

PubMed

Amarouche, Nassima; Boudesocque, Leslie; Borie, Nicolas; Giraud, Matthieu; Forni, Luciano; Butte, Alessandro; Edwards, Florence; Renault, Jean-Hugues

2014-06-01

A new type 1 ternary biphasic system composed of cyclopentyl methyl ether, dimethylformamide and water was developed, characterized and successfully used for the purification of a lipophilic, protected peptide by pH-zone refining centrifugal partition chromatography. The protected peptide is an 8-mer, key intermediate in bivalirudin (Angiomax®) synthesis and shows a very low solubility in the solvents usually used in liquid chromatography. All ionic groups, except the N-terminal end of the peptide, are protected by a benzyl group. The purification of this peptide was achieved with a purity of about 99.04% and a recovery of 94% using the new ternary biphasic system cyclopentyl methyl ether/dimethylformamide/water (49:40:11, v/v) in the descending pH-zone refining mode with triethylamine (28 mM) as the retainer and methanesulfonic acid (18 mM) as the eluter. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Purification of selenium by zone refining

NASA Astrophysics Data System (ADS)

Burger, A.; Henderson, D. O.; Morgan, S. H.; Feng, J.; Silberman, E.

1990-11-01

We studied the purification of Se using zone refining, with emphasis on the efficiency of this technique in removing the Cu impurity, which is known to be related to a trapping center in CdSe. After 78 passes it was found that Cu accumulates at one end section of the ingot, while at the opposite end the level was below the detection limit of the atomic absorption spectroscopic analysis employed. Infrared spectroscopic data, differential solubility and differential scanning calorimetry measurements also indicate that the effective distribution coefficient, k, for the Cu solute, is less than 1. A model for the various phases present during zone melting is presented and the possibility of segregating impurities having k>1 is discussed.

Processes of multibathyal aragonite undersaturation in the Arctic Ocean

USGS Publications Warehouse

Wynn, J.G.; Robbins, L.L.; Anderson, L.G.

2016-01-01

During 3 years of study (2010–2012), the western Arctic Ocean was found to have unique aragonite saturation profiles with up to three distinct aragonite undersaturation zones. This complexity is produced as inflow of Atlantic-derived and Pacific-derived water masses mix with Arctic-derived waters, which are further modified by physiochemical and biological processes. The shallowest aragonite undersaturation zone, from the surface to ∼30 m depth is characterized by relatively low alkalinity and other dissolved ions. Besides local influence of biological processes on aragonite undersaturation of shallow coastal waters, the nature of this zone is consistent with dilution by sea-ice melt and invasion of anthropogenic CO2 from the atmosphere. A second undersaturated zone at ∼90–220 m depth (salinity ∼31.8–35.4) occurs within the Arctic Halocline and is characterized by elevated pCO2 and nutrients. The nature of this horizon is consistent with remineralization of organic matter on shallow continental shelves bordering the Canada Basin and the input of the nutrients and CO2 entrained by currents from the Pacific Inlet. Finally, the deepest aragonite undersaturation zone is at greater than 2000 m depth and is controlled by similar processes as deep aragonite saturation horizons in the Atlantic and Pacific Oceans. The comparatively shallow depth of this deepest aragonite saturation horizon in the Arctic is maintained by relatively low temperatures, and stable chemical composition. Understanding the mechanisms controlling the distribution of these aragonite undersaturation zones, and the time scales over which they operate will be crucial to refine predictive models.

Estimating changes in urban land and urban population using refined areal interpolation techniques

NASA Astrophysics Data System (ADS)

Zoraghein, Hamidreza; Leyk, Stefan

2018-05-01

The analysis of changes in urban land and population is important because the majority of future population growth will take place in urban areas. U.S. Census historically classifies urban land using population density and various land-use criteria. This study analyzes the reliability of census-defined urban lands for delineating the spatial distribution of urban population and estimating its changes over time. To overcome the problem of incompatible enumeration units between censuses, regular areal interpolation methods including Areal Weighting (AW) and Target Density Weighting (TDW), with and without spatial refinement, are implemented. The goal in this study is to estimate urban population in Massachusetts in 1990 and 2000 (source zones), within tract boundaries of the 2010 census (target zones), respectively, to create a consistent time series of comparable urban population estimates from 1990 to 2010. Spatial refinement is done using ancillary variables such as census-defined urban areas, the National Land Cover Database (NLCD) and the Global Human Settlement Layer (GHSL) as well as different combinations of them. The study results suggest that census-defined urban areas alone are not necessarily the most meaningful delineation of urban land. Instead, it appears that alternative combinations of the above-mentioned ancillary variables can better depict the spatial distribution of urban land, and thus make it possible to reduce the estimation error in transferring the urban population from source zones to target zones when running spatially-refined temporal areal interpolation.

Changing Urbania: Estimating Changes in Urban Land and Urban Population Using Refined Areal Interpolation Techniques

NASA Astrophysics Data System (ADS)

Zoraghein, H.; Leyk, S.; Balk, D.

2017-12-01

The analysis of changes in urban land and population is important because the majority of future population growth will take place in urban areas. The U.S. Census historically classifies urban land using population density and various land-use criteria. This study analyzes the reliability of census-defined urban lands for delineating the spatial distribution of urban population and estimating its changes over time. To overcome the problem of incompatible enumeration units between censuses, regular areal interpolation methods including Areal Weighting (AW) and Target Density Weighting (TDW), with and without spatial refinement, are implemented. The goal in this study is to estimate urban population in Massachusetts in 1990 and 2000 (source zones), within tract boundaries of the 2010 census (target zones), respectively, to create a consistent time series of comparable urban population estimates from 1990 to 2010. Spatial refinement is done using ancillary variables such as census-defined urban areas, the National Land Cover Database (NLCD) and the Global Human Settlement Layer (GHSL) as well as different combinations of them. The study results suggest that census-defined urban areas alone are not necessarily the most meaningful delineation of urban land. Instead it appears that alternative combinations of the above-mentioned ancillary variables can better depict the spatial distribution of urban land, and thus make it possible to reduce the estimation error in transferring the urban population from source zones to target zones when running spatially-refined temporal areal interpolation.

Effect of pulsed current GTA welding parameters on the fusion zone microstructure of AA 6061 aluminium alloy

NASA Astrophysics Data System (ADS)

Kumar, T. Senthil; Balasubramanian, V.; Babu, S.; Sanavullah, M. Y.

2007-08-01

AA6061 aluminium alloy (Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of food processing equipment, chemical containers, passenger cars, road tankers, and railway transport systems. The preferred process for welding these aluminium alloys is frequently Gas Tungsten Arc (GTA) welding due to its comparatively easy applicability and lower cost. In the case of single pass GTA welding of thinner sections of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current processes. The use of pulsed current parameters has been found to improve the mechanical properties of the welds compared to those of continuous current welds of this alloy due to grain refinement occurring in the fusion zone. In this investigation, an attempt has been made to develop a mathematical model to predict the fusion zone grain diameter incorporating pulsed current welding parameters. Statistical tools such as design of experiments, analysis of variance, and regression analysis are used to develop the mathematical model. The developed model can be effectively used to predict the fusion grain diameter at a 95% confidence level for the given pulsed current parameters. The effect of pulsed current GTA welding parameters on the fusion zone grain diameter of AA 6061 aluminium alloy welds is reported in this paper.

Mesh Convergence Requirements for Composite Damage Models

NASA Technical Reports Server (NTRS)

Davila, Carlos G.

2016-01-01

The ability of the finite element method to accurately represent the response of objects with intricate geometry and loading renders the finite element method as an extremely versatile analysis technique for structural analysis. Finite element analysis is routinely used in industry to calculate deflections, stress concentrations, natural frequencies, buckling loads, and much more. The method works by discretizing complex problems into smaller, simpler approximations that are valid over small uniform domains. For common analyses, the maximum size of the elements that can be used is often be determined by experience. However, to verify the quality of a solution, analyses with several levels of mesh refinement should be performed to ensure that the solution has converged. In recent years, the finite element method has been used to calculate the resistance of structures, and in particular that of composite structures. A number of techniques such as cohesive zone modeling, the virtual crack closure technique, and continuum damage modeling have emerged that can be used to predict cracking, delaminations, fiber failure, and other composite damage modes that lead to structural collapse. However, damage models present mesh refinement requirements that are not well understood. In this presentation, we examine different mesh refinement issues related to the representation of damage in composite materials. Damage process zone sizes and their corresponding mesh requirements will be discussed. The difficulties of modeling discontinuities and the associated need for regularization techniques will be illustrated, and some unexpected element size constraints will be presented. Finally, some of the difficulties in constructing models of composite structures capable of predicting transverse matrix cracking will be discussed. It will be shown that to predict the initiation and propagation of transverse matrix cracks, their density, and their saturation may require models that are significantly more refined than those that have been contemplated in the past.

78 FR 25698 - Foreign-Trade Zone 99-Wilmington, Delaware; Application for Expansion of Subzone 99E; Delaware...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-02

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-38-2013] Foreign-Trade Zone 99--Wilmington, Delaware; Application for Expansion of Subzone 99E; Delaware City Refining Company LLC; New Castle County... (grantee of FTZ 99), through the Delaware Economic Development Office, requesting the expansion of Subzone...

Experimental Characterization of Electron Beam Welded SAE 5137H Thick Steel Plate

NASA Astrophysics Data System (ADS)

Kattire, Prakash; Bhawar, Valmik; Thakare, Sandeep; Patil, Sachin; Mane, Santosh; Singh, Rajkumar, Dr.

2017-09-01

Electron beam welding is known for its narrow weld zone with high depth to width ratio, less heat affected zone, less distortion and contamination. Electron beam welding is fusion welding process, where high velocity electrons impinge on material joint to be welded and kinetic energy of this electron is transformed into heat upon impact to fuse the material. In the present work electron beam welding of 60 mm thick SAE 5137H steel is studied. Mechanical and metallurgical properties of electron beam welded joint of SAE 5137H were evaluated. Mechanical properties are analysed by tensile, impact and hardness test. Metallurgical properties are investigated through optical and scanning electron microscope. The hardness traverse across weld zone shows HV 370-380, about 18% increase in the tensile strength and very low toughness of weld joint compared to parent metal. Microstructural observation shows equiaxed dendrite in the fusion zone and partial grain refinement was found in the HAZ.

Separation of chlorogenic acid and concentration of trace caffeic acid from natural products by pH-zone-refining countercurrent chromatography.

PubMed

Lu, Yuanyuan; Dong, Genlai; Gu, Yanxiang; Ito, Yoichiro; Wei, Yun

2013-07-01

Chlorogenic acid and caffeic acid were selected as test samples for separation by the pH-zone-refining countercurrent chromatography (CCC). The separation of these test samples was performed with a two-phase solvent system composed of methyl-tert-butyl-ether/acetonitrile/water at a volume ratio of 4:1:5 v/v/v where trifluoroacetic acid (TFA; 8 mM) was added to the organic stationary phase as a retainer and NH4 OH (10 mM) to the aqueous mobile phase as an eluter. Chlorogenic acid was successfully separated from Flaveria bidentis (L.) Kuntze (F. bidentis) and Lonicerae Flos by pH-zone-refining CCC, a slightly polar two-phase solvent system composed of methyl-tert-butyl-ether/acetonitrile/n-butanol/water at a volume ratio of 4:1:1:5 v/v/v/v was selected where TFA (3 mM) was added to the organic stationary phase as a retainer and NH4 OH (3 mM) to the aqueous mobile phase as an eluter. A 16.2 mg amount of chlorogenic acid with the purity of 92% from 1.4 g of F. bidentis, and 134 mg of chlorogenic acid at the purity of 99% from 1.3 g of crude extract of Lonicerae Flos have been obtained. These results suggest that pH-zone-refining CCC is suitable for the isolation of the chlorogenic acid from the crude extracts of F. bidentis and Lonicerae Flos. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Containerless processing of beryllium

NASA Technical Reports Server (NTRS)

Wouch, G.; Keith, G. H.; Frost, R. T.; Pinto, N. P.

1977-01-01

Melting and solidification of a beryllium alloy containing 1.5% BeO by weight in the weightless environment of space has produced cast beryllium with a relatively uniform dispersion of BeO throughout. Examination of the cast material shows that it is coarse grained, although the BeO is not heavily agglomerated in the flight specimen. Ground based comparison experiments show extreme agglomeration and segregation of BeO, resulting in large zones which are practically free of the oxide. Several postulated hypotheses for the failure to grain refine the beryllium are formulated. These are: (1) spherodization of the BeO particles during specimen preparation and during the molten phase of the experiment; (2) loss of nucleation potency through aging in the molten phase; and (3) inability of BeO to act as a grain refiner for beryllium. Further investigation with non spherodized particles and shorter dwell times molten may delineate which of these hypotheses are valid. The results of this flight experiment indicate that the weightless environment of space is an important asset in conducting research to find grain refiners for beryllium and other metals for which cast dispersions of grain refining agents cannot be prepared terrestrially due to gravitationally driven settling and agglomeration.

Effect of medium on friction and wear properties of compacted graphite cast iron processed by biomimetic coupling laser remelting process

NASA Astrophysics Data System (ADS)

Guo, Qing-chun; Zhou, Hong; Wang, Cheng-tao; Zhang, Wei; Lin, Peng-yu; Sun, Na; Ren, Luquan

2009-04-01

Stimulated by the cuticles of soil animals, an attempt to improve the wear resistance of compact graphite cast iron (CGI) with biomimetic units on the surface was made by using a biomimetic coupled laser remelting process in air and various thicknesses water film, respectively. The microstructures of biomimetic units were examined by scanning electron microscope and X-ray diffraction was used to describe the microstructure and identify the phases in the melted zone. Microhardness was measured and the wear behaviors of biomimetic specimens as functions of different mediums as well as various water film thicknesses were investigated under dry sliding condition, respectively. The results indicated that the microstructure zones in the biomimetic specimens processed with water film are refined compared with that processed in air and had better wear resistance increased by 60%, the microhardness of biomimetic units has been improved significantly. The application of water film provided finer microstructures and much more regular grain shape in biomimetic units, which played a key role in improving the friction properties and wear resistance of CGI.

A process model for the heat-affected zone microstructure evolution in duplex stainless steel weldments: Part II. Application to electron beam welding

NASA Astrophysics Data System (ADS)

Hemmer, H.; Grong, Ø.; Klokkehaug, S.

2000-03-01

In the present investigation, a process model for electron beam (EB) welding of different grades of duplex stainless steels (i.e. SAF 2205 and 2507) has been developed. A number of attractive features are built into the original finite element code, including (1) a separate module for prediction of the penetration depth and distribution of the heat source into the plate, (2) adaptive refinement of the three-dimensional (3-D) element mesh for quick and reliable solution of the differential heat flow equation, and (3) special subroutines for calculation of the heat-affected zone (HAZ) microstructure evolution. The process model has been validated by comparison with experimental data obtained from in situ thermocouple measurements and optical microscope examinations. Subsequently, its aptness to alloy design and optimization of welding conditions for duplex stainless steels is illustrated in different numerical examples and case studies pertaining to EB welding of tubular joints.

Gas-Enhanced Ultra-High Shear Mixing: A Concept and Applications

NASA Astrophysics Data System (ADS)

Czerwinski, Frank; Birsan, Gabriel

2017-04-01

The processes of mixing, homogenizing, and deagglomeration are of paramount importance in many industries for modifying properties of liquids or liquid-based dispersions at room temperature and treatment of molten or semi-molten alloys at high temperatures, prior to their solidification. To implement treatments, a variety of technologies based on mechanical, electromagnetic, and ultrasonic principles are used commercially or tested at the laboratory scale. In a large number of techniques, especially those tailored toward metallurgical applications, the vital role is played by cavitation, generation of gas bubbles, and their interaction with the melt. This paper describes a novel concept exploring an integration of gas injection into the shear zone with ultra-high shear mixing. As revealed via experiments with a prototype of the cylindrical rotor-stator apparatus and transparent media, gases injected radially through the high-speed rotor generate highly refined bubbles of high concentration directly in the shear zone of the mixer. It is believed that an interaction of large volume of fine gas bubbles with the liquid, superimposed on ultra-high shear, will enhance mixing capabilities and cause superior refining and homogenizing of the liquids or solid-liquid slurries, thus allowing their effective property modification.

Analysis of contact zones from whole field isochromatics using reflection photoelasticity

NASA Astrophysics Data System (ADS)

Hariprasad, M. P.; Ramesh, K.

2018-06-01

This paper discusses the method for evaluating the unknown contact parameters by post processing the whole field fringe order data obtained from reflection photoelasticity in a nonlinear least squares sense. Recent developments in Twelve Fringe Photoelasticity (TFP) for fringe order evaluation from single isochromatics is utilized for the whole field fringe order evaluation. One of the issues in using TFP for reflection photoelasticity is the smudging of isochromatic data at the contact zone. This leads to error in identifying the origin of contact, which is successfully addressed by implementing a semi-automatic contact point refinement algorithm. The methodologies are initially verified for benchmark problems and demonstrated for two application problems of turbine blade and sheet pile contacting interfaces.

Combinative application of pH-zone-refining and conventional high-speed counter-current chromatography for preparative separation of caged polyprenylated xanthones from gamboge.

PubMed

Xu, Min; Fu, Wenwei; Zhang, Baojun; Tan, Hongsheng; Xiu, Yanfeng; Xu, Hongxi

2016-02-01

An efficient method for the preparative separation of four structurally similar caged xanthones from the crude extracts of gamboge was established, which involves the combination of pH-zone-refining counter-current chromatography and conventional high-speed counter-current chromatography for the first time. pH-zone-refining counter-current chromatography was performed with the solvent system composed of n-hexane/ethyl acetate/methanol/water (7:3:8:2, v/v/v/v), where 0.1% trifluoroacetic acid was added to the upper organic stationary phase as a retainer and 0.03% triethylamine was added to the aqueous mobile phase as an eluter. From 3.157 g of the crude extract, 1.134 g of gambogic acid, 180.5 mg of gambogenic acid and 572.9 mg of a mixture of two other caged polyprenylated xanthones were obtained. The mixture was further separated by conventional high-speed counter-current chromatography with a solvent system composed of n-hexane/ethyl acetate/methanol/water (5:5:10:5, v/v/v/v) and n-hexane/methyl tert-butyl ether/acetonitrile/water (8:2:6:4,v/v/v/v), yielding 11.6 mg of isogambogenic acid and 10.4 mg of β-morellic acid from 218.0 mg of the mixture, respectively. The purities of all four of the compounds were over 95%, as determined by high-performance liquid chromatography, and the chemical structures of the four compounds were confirmed by electrospray ionization mass spectrometry and NMR spectroscopy. The combinative application of pH-zone-refining counter-current chromatography and conventional high-speed counter-current chromatography shows great advantages in isolating and enriching the caged polyprenylated xanthones. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Revalidation of an Instrument to Measure Zones of Indifference of Teachers to Directives Issued by Administrators.

ERIC Educational Resources Information Center

Wilkes, Sam T.; Blackbourn, Joe M.

This project attempts to refine the Zones of Indifference Instrument, (included in appendix) that measures zones of indifference of teachers to typical directives issued by administrators. As a result of the original validation study, a 78-item, two-factor instrument was developed. These two factors explained 52 percent of the variance. The…

Bridgman-Stockbarger growth of SrI2:Eu2+ single crystal

NASA Astrophysics Data System (ADS)

Raja, A.; Daniel, D. Joseph; Ramasamy, P.; Singh, S. G.; Sen, S.; Gadkari, S. C.

2018-05-01

Strontium Iodide (SrI2): Europium Iodide (EuI2) was purified by Zone-refinement process. Europium doped strontium iodide (SrI2:Eu2+) single crystal was grown by modified vertical Bridgman - Stockbarger technique. Photoluminescence (PL) excitation and emission (PLE) spectra were measured for Eu2+ doped SrI2 crystal. The sharp emission was recorded at 432 nm. Scintillation properties of the SrI2:Eu2+ crystal were checked by the gamma ray spectrometer using 137Cs gamma source.

Finite element simulation of the T-shaped ECAP processing of round samples

NASA Astrophysics Data System (ADS)

Shaban Ghazani, Mehdi; Fardi-Ilkhchy, Ali; Binesh, Behzad

2018-05-01

Grain refinement is the only mechanism that increases the yield strength and toughness of the materials simultaneously. Severe plastic deformation is one of the promising methods to refine the microstructure of materials. Among different severe plastic deformation processes, the T-shaped equal channel angular pressing (T-ECAP) is a relatively new technique. In the present study, finite element analysis was conducted to evaluate the deformation behavior of metals during T-ECAP process. The study was focused mainly on flow characteristics, plastic strain distribution and its homogeneity, damage development, and pressing force which are among the most important factors governing the sound and successful processing of nanostructured materials by severe plastic deformation techniques. The results showed that plastic strain is localized in the bottom side of sample and uniform deformation cannot be possible using T-ECAP processing. Friction coefficient between sample and die channel wall has a little effect on strain distributions in mirror plane and transverse plane of deformed sample. Also, damage analysis showed that superficial cracks may be initiated from bottom side of sample and their propagation will be limited due to the compressive state of stress. It was demonstrated that the V shaped deformation zone are existed in T-ECAP process and the pressing load needed for execution of deformation process is increased with friction.

Refined images of the crust around the SAFOD drill site derived from combined active and passive seismic experiment data

NASA Astrophysics Data System (ADS)

Roecker, S.; Thurber, C.; Shuler, A.; Liu, Y.; Zhang, H.; Powell, L.

2005-12-01

Five years of effort collecting and analyzing earthquake and explosion data in the vicinity of the SAFOD drill site culminated in the determination of the final trajectory for summer 2005's Phase 2 drilling. The trajectory was defined to optimize the chance of reaching one of two adjacent M2 "target earthquake" fault patches, whose centroids are separated horizontally by about 50 meters, with one or more satellite coreholes planned for Phase 3 drilling in summer 2007. Some of the most critical data for the final targeting were explosion data recorded on a Paulsson Geophysical Services, Inc., 80-element 3-component borehole string and earthquake data recorded on a pair of 3-component Duke University geophones in the SAFOD borehole. We are now utilizing the full 5-year dataset to refine our knowledge of three-dimensional (3D) crustal structure, wave propagation characteristics, and earthquake locations around SAFOD. These efforts are proceeding in parallel in several directions. Improved picks from a careful reanalysis of shear waves observed on the PASO array will be used in deriving an improved tomographic 3D wavespeed model. We are using finite-difference waveform modeling to investigate waveform complexity for earthquakes in and near the target region, including fault-zone head waves and strong secondary S-wave arrivals. A variety of waveform imaging methods are being applied to image fine-scale 3D structure and subsurface scatterers, including fault zones. In the process, we aim to integrate geophysical logging and geologic observations with our models to try to associate the target region earthquake activity, which is occurring on two fault strands about 280 meters apart, with shear zones encountered in the SAFOD Phase-2 borehole. These observations will be agumented and the target earthquake locations further refined over the next 2 years through downhole and surface recording of natural earthquakes and surface shots conducted at PASO station locations.

Development of SiC Nanoparticles and Second Phases Synergistically Reinforced Mg-Based Composites Processed by Multi-Pass Forging with Varying Temperatures

PubMed Central

Nie, Kaibo; Guo, Yachao; Deng, Kunkun; Wang, Xiaojun; Wu, Kun

2018-01-01

In this study, SiC nanoparticles were added into matrix alloy through a combination of semisolid stirring and ultrasonic vibration while dynamic precipitation of second phases was obtained through multi-pass forging with varying temperatures. During single-pass forging of the present composite, as the deformation temperature increased, the extent of recrystallization increased, and grains were refined due to the inhibition effect of the increasing amount of dispersed SiC nanoparticles. A small amount of twins within the SiC nanoparticle dense zone could be found while the precipitated phases of Mg17Al12 in long strips and deformation bands with high density dislocations were formed in the particle sparse zone after single-pass forging at 350 °C. This indicated that the particle sparse zone was mainly deformed by dislocation slip while the nanoparticle dense zone may have been deformed by twinning. The yield strength and ultimate tensile strength of the composites were gradually enhanced through increasing the single-pass forging temperature from 300 °C to 400 °C, which demonstrated that initial high forging temperature contributed to the improvement of the mechanical properties. During multi-pass forging with varying temperatures, the grain size of the composite was gradually decreased while the grain size distribution tended to be uniform with reducing the deformation temperature and extending the forging passes. In addition, the amount of precipitated second phases was significantly increased compared with that after multi-pass forging under a constant temperature. The improvement in the yield strength of the developed composite was related to grain refinement strengthening and Orowan strengthening resulting from synergistical effect of the externally applied SiC nanoparticles and internally precipitated second phases. PMID:29342883

Development of SiC Nanoparticles and Second Phases Synergistically Reinforced Mg-Based Composites Processed by Multi-Pass Forging with Varying Temperatures.

PubMed

Nie, Kaibo; Guo, Yachao; Deng, Kunkun; Wang, Xiaojun; Wu, Kun

2018-01-13

In this study, SiC nanoparticles were added into matrix alloy through a combination of semisolid stirring and ultrasonic vibration while dynamic precipitation of second phases was obtained through multi-pass forging with varying temperatures. During single-pass forging of the present composite, as the deformation temperature increased, the extent of recrystallization increased, and grains were refined due to the inhibition effect of the increasing amount of dispersed SiC nanoparticles. A small amount of twins within the SiC nanoparticle dense zone could be found while the precipitated phases of Mg 17 Al 12 in long strips and deformation bands with high density dislocations were formed in the particle sparse zone after single-pass forging at 350 °C. This indicated that the particle sparse zone was mainly deformed by dislocation slip while the nanoparticle dense zone may have been deformed by twinning. The yield strength and ultimate tensile strength of the composites were gradually enhanced through increasing the single-pass forging temperature from 300 °C to 400 °C, which demonstrated that initial high forging temperature contributed to the improvement of the mechanical properties. During multi-pass forging with varying temperatures, the grain size of the composite was gradually decreased while the grain size distribution tended to be uniform with reducing the deformation temperature and extending the forging passes. In addition, the amount of precipitated second phases was significantly increased compared with that after multi-pass forging under a constant temperature. The improvement in the yield strength of the developed composite was related to grain refinement strengthening and Orowan strengthening resulting from synergistical effect of the externally applied SiC nanoparticles and internally precipitated second phases.

The preparation of pure niobium for neutron dosimetry purposes

NASA Astrophysics Data System (ADS)

Schulze, Klaus; Krehl, Michael

1985-06-01

A technique is described for the preparation of high purity niobium for use in fast neutron dosimetry. Based on results of known purification processes for niobium, an optimized method has been developed, consisting of: (1) a double electrolytic refining in an eutectic lithium-, sodium-, potassium-fluoride melt, containing fluoro-potassium niobate (K 2NbF 7), (2) electron beam float zone melting (EBFZM) in ultra high vacuum (UHV) and (3) UHV treatments. Starting with EBFZM of niobium of commercial quality (140 μg/g Ta, 35 μg/g W) the tantalum and tungsten contents were reduced by a first electrolysis to approximately 4 and 4 × 10 -2 μg/g, respectively. For a second electrolytic refining using a salt bath with extremely low tantalum and tungsten contents, this material was subjected to an additional EBFZM process. The niobium metal produced by this step was three times zone melted to reduce those elements (e.g. Fe, Co, Ni, O, N) which increased during the electrolyses. Material produced by this technique has impurity concentrations below 0.4 μg/g of tantalum and 10 -2 μg/g of tungsten. The concentration of the interstitials (C, O, N except H) is below the detection limit of classical analytical methods. A further reduction of the interstitials by annealing treatments in UHV of this material resulted in an electrical residual resistivity ratio (RRR) ρ(295 K)/ ρ(4.2 K) = 24 500 indicating an impurity concentration far below 1 μg/g.

Quantifying the fire regime distributions for severity in Yosemite National Park, California, USA

USGS Publications Warehouse

Thode, Andrea E.; van Wagtendonk, Jan W.; Miller, Jay D.; Quinn, James F.

2011-01-01

This paper quantifies current fire severity distributions for 19 different fire-regime types in Yosemite National Park, California, USA. Landsat Thematic Mapper remote sensing data are used to map burn severity for 99 fires (cumulatively over 97 000 ha) that burned in Yosemite over a 20-year period. These maps are used to quantify the frequency distributions of fire severity by fire-regime type. A classification is created for the resultant distributions and they are discussed within the context of four vegetation zones: the foothill shrub and woodland zone; the lower montane forest zone; the upper montane forest zone and the subalpine forest zone. The severity distributions can form a building block from which to discuss current fire regimes across the Sierra Nevada in California. This work establishes a framework for comparing the effects of current fires on our landscapes with our notions of how fires historically burned, and how current fire severity distributions differ from our desired future conditions. As this process is refined, a new set of information will be available to researchers and land managers to help understand how fire regimes have changed from the past and how we might attempt to manage them in the future.

Microstructural characterization in dissimilar friction stir welding between 304 stainless steel and st37 steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jafarzadegan, M.; State Key Laboratory of Advanced Welding Production Technology, School of Materials Science and Eng., Harbin Institute of Technology, P.O. Box: 150001, Harbin; Feng, A.H.

2012-12-15

In the present study, 3 mm-thick plates of 304 stainless steel and st37 steel were welded together by friction stir welding at a welding speed of 50 mm/min and tool rotational speed of 400 and 800 rpm. X-ray diffraction test was carried out to study the phases which might be formed in the welds. Metallographic examinations, and tensile and microhardness tests were used to analyze the microstructure and mechanical properties of the joint. Four different zones were found in the weld area except the base metals. In the stir zone of the 304 stainless steel, a refined grain structure withmore » some features of dynamic recrystallization was evidenced. A thermomechanically-affected zone was characterized on the 304 steel side with features of dynamic recovery. In the other side of the stir zone, the hot deformation of the st37 steel in the austenite region produced small austenite grains and these grains transformed to fine ferrite and pearlite and some products of displacive transformations such as Widmanstatten ferrite and martensite by cooling the material after friction stir welding. The heat-affected zone in the st37 steel side showed partially and fully refined microstructures like fusion welding processes. The recrystallization in the 304 steel and the transformations in the st37 steel enhanced the hardness of the weld area and therefore, improved the tensile properties of the joint. - Highlights: Black-Right-Pointing-Pointer FSW produced sound welds between st37 low carbon steel and 304 stainless steel. Black-Right-Pointing-Pointer The SZ of the st37 steel contained some products of allotropic transformation. Black-Right-Pointing-Pointer The material in the SZ of the 304 steel showed features of dynamic recrystallization. Black-Right-Pointing-Pointer The finer microstructure in the SZ increased the hardness and tensile strength.« less

Integrated melt inclusion and crystal zoning study to track the timescales and pre-eruption dynamics of violent Strombolian eruptions at Llaima volcano, Chile

NASA Astrophysics Data System (ADS)

Ruth, D. C.; Costa Rodriguez, F.; Bouvet de Maisonneuve, C.; Calder, E. S.

2013-12-01

Melt inclusion compositions in crystals from many volcanic systems are notoriously variable and some times difficult to interpret. Their compositions can be a combination of rapid crystal growth, entrapment of local melt, and diffusive re-equilibration, among other processes. Additionally, chemical zoning in olivine records changing environmental conditions, most importantly temperature and magma composition. Many geochemical studies focus on either melt inclusion data or chemical zoning data to ascertain volcanic processes. Here we combine melt inclusion data with that of chemical zoning of the olivine host crystals from the 2008 violent Strombolian eruption of Llaima volcano, Chile, to obtain a more refined understanding of the processes related to crystal growth, melt inclusion formation, and magma dynamics. We investigated zoning characteristics in a suite of olivine crystals, created X-ray element maps (Al, Ca, Mg, P, Fe), and collected quantitative elemental abundances across chemical zones for detailed diffusion modeling. Melt inclusion compositions were collected via electron microprobe analysis and LA-ICPMS. We observe three types of zoning in the host olivine crystals: normal, reverse, and multiple zones with fluctuating Fo content. Reverse zoning was more common than the other types. Regardless of zoning character, multiple melt inclusions are present within a given olivine, often found near the crystal rim. For some of these melt inclusions, the olivine surrounding the melt inclusion was also zoned, often to a similar composition as the olivine rim. This implies that these inclusions remained connected with interstitial matrix melt until melt inclusion closure. These ';open' melt inclusions exhibited slightly different major (higher SiO2, Na2O+K2O, TiO2) and trace elements (positive Eu and Sr anomalies) compared to melt inclusions in the same olivine that were not surrounded by compositional zoning. Quantitative elemental profiles produce modeled timescales on the order of 10s-100s days prior to eruption. Zoning textures, melt inclusion compositions, and timescale modeling indicates that crystal dissolution (open melt inclusions), mafic magma injection (reverse zoning), and partial melting of upper crustal plagioclase-rich cumulates (positive Eu and Sr anomalies) were occurring in the months prior to the 2008 eruption. The combination of both melt inclusion data and textural data of the host crystals provides deeper insight into the nature and timing of deep and shallow reservoir processes that generate violent Strombolian eruptions at Llaima.

Iron-absorption band analysis for the discrimination of iron-rich zones

NASA Technical Reports Server (NTRS)

Rowan, L. C. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Study has concentrated on the two primary aspects of the project, structural analysis through evaluation of lineaments and circular features and spectral analyses through digital computer-processing techniques. Several previously unrecognized lineaments are mapped which may be the surface manifestations of major fault or fracture zones. Two of these, the Walker Lane and the Midas Trench lineament system, transect the predominantly NNE-NNW-trending moutain ranges for more than 500 km. Correlation of major lineaments with productive mining districts implies a genetic relationship, the 50 circular or elliptical features delineated suggest a related role for Tertiary volcanism. Color-ratio composites have been used to identify limonitic zones and to discriminate mafic and felsic rock by combing diazo color transparencies of three different ratios. EROS Data Center scene identification number for color composite in this report is ER 1 CC 500. Refinement of enhancement procedures for the ratio images is progressing. Fieldwork in coordination with both spectral and structural analyses is underway.

Improving precipitation hardening behavior of Mg−Zn based alloys with Ce−Ca microalloying additions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langelier, B., E-mail: langelb@mcmaster.ca

2016-10-15

The precipitation hardening behavior of newly developed Mg−Zn−Ca−Ce alloys, with modified texture and improved ductility, is studied to delineate the microstructural characteristics that lead to effective hardening upon ageing treatments. Advanced electron microscopy and atom probe techniques are used to analyze the structural characteristics in relevance to the hardening potential. It has been found that the formation of a new basal precipitate phase, which evolves from a single atomic layer GP zone, and is finely distributed in both under-aged and peak-aged microstructures, has a significant impact in the improvement of the hardening response compared with the base Mg−Zn alloys. Itmore » has also been found that the β′{sub 1} rod precipitates, commonly formed during ageing treatments of Mg−Zn alloys, have their size and distribution significantly refined in the Ca−Ce containing alloys. The role of alloy chemistry in the formation of the fine basal plate GP zones and the refinement in β′{sub 1} precipitation and their relationships to the hardening behavior are discussed. It is proposed that Ca microalloying governs the formation of the GP zones and the enhancement of hardening, particularly in the under-aged conditions, but that this is aided by a beneficial effect from Ce. - Highlights: • Ce−Ca microalloying additions improve hardening in Mg−Zn, over Ce or Ca alone. • Improved hardening is due to refined β′{sub 1} rods, and fine basal plate precipitates. • Atom probe tomography identifies Ca in both β′{sub 1} and the fine basal plates. • The fine basal plates originate as ordered monolayer GP zones with 1:1 Zn:Ca (at.%). • With ageing GP zones become more Zn-rich and transform to the fine basal plates.« less

Thermal Protection System Imagery Inspection Management System -TIIMS

NASA Technical Reports Server (NTRS)

Goza, Sharon; Melendrez, David L.; Henningan, Marsha; LaBasse, Daniel; Smith, Daniel J.

2011-01-01

TIIMS is used during the inspection phases of every mission to provide quick visual feedback, detailed inspection data, and determination to the mission management team. This system consists of a visual Web page interface, an SQL database, and a graphical image generator. These combine to allow a user to ascertain quickly the status of the inspection process, and current determination of any problem zones. The TIIMS system allows inspection engineers to enter their determinations into a database and to link pertinent images and video to those database entries. The database then assigns criteria to each zone and tile, and via query, sends the information to a graphical image generation program. Using the official TIPS database tile positions and sizes, the graphical image generation program creates images of the current status of the orbiter, coloring zones, and tiles based on a predefined key code. These images are then displayed on a Web page using customized JAVA scripts to display the appropriate zone of the orbiter based on the location of the user's cursor. The close-up graphic and database entry for that particular zone can then be seen by selecting the zone. This page contains links into the database to access the images used by the inspection engineer when they make the determination entered into the database. Status for the inspection zones changes as determinations are refined and shown by the appropriate color code.

Mineral commodity profiles: Germanium

USGS Publications Warehouse

Butterman, W.C.; Jorgenson, John D.

2005-01-01

Overview -- Germanium is a hard, brittle semimetal that first came into use a half-century ago as a semiconductor material in radar units and as the material from which the first transistor was made. Today it is used principally as a component of the glass in telecommunications fiber optics; as a polymerization catalyst for polyethylene terephthalate (PET), a commercially important plastic; in infrared (IR) night vision devices; and as a semiconductor and substrate in electronics circuitry. Most germanium is recovered as a byproduct of zinc smelting, although it also has been recovered at some copper smelters and from the fly ash of coal-burning industrial powerplants. It is a highly dispersed element, associated primarily with base-metal sulfide ores. In the United States, germanium is recovered from zinc smelter residues and manufacturing scrap and is refined by two companies at four germanium refineries. One of the four refineries is dedicated to processing scrap. In 2000, producers sold zone-refined (high-purity) germanium at about $1,250 per kilogram and electronic-grade germanium dioxide (GeO2) at $800 per kilogram. Domestic refined production was valued at $22 million. Germanium is a critical component in highly technical devices and processes. It is likely to remain in demand in the future at levels at least as high as those of 2000. U.S. resources of germanium are probably adequate to meet domestic needs for several decades.

Effect of Pulse Parameters on Weld Quality in Pulsed Gas Metal Arc Welding: A Review

NASA Astrophysics Data System (ADS)

Pal, Kamal; Pal, Surjya K.

2011-08-01

The weld quality comprises bead geometry and its microstructure, which influence the mechanical properties of the weld. The coarse-grained weld microstructure, higher heat-affected zone, and lower penetration together with higher reinforcement reduce the weld service life in continuous mode gas metal arc welding (GMAW). Pulsed GMAW (P-GMAW) is an alternative method providing a better way for overcoming these afore mentioned problems. It uses a higher peak current to allow one molten droplet per pulse, and a lower background current to maintain the arc stability. Current pulsing refines the grains in weld fusion zone with increasing depth of penetration due to arc oscillations. Optimum weld joint characteristics can be achieved by controlling the pulse parameters. The process is versatile and easily automated. This brief review illustrates the effect of pulse parameters on weld quality.

An efficient and target-oriented sample enrichment method for preparative separation of minor alkaloids by pH-zone-refining counter-current chromatography.

PubMed

Feng, Rui-Hong; Hou, Jin-Jun; Zhang, Yi-Bei; Pan, Hui-Qin; Yang, Wenzhi; Qi, Peng; Yao, Shuai; Cai, Lu-Ying; Yang, Min; Jiang, Bao-Hong; Liu, Xuan; Wu, Wan-Ying; Guo, De-An

2015-08-28

An efficient and target-oriented sample enrichment method was established to increase the content of the minor alkaloids in crude extract by using the corresponding two-phase solvent system applied in pH-zone-refining counter-current chromatography. The enrichment and separation of seven minor indole alkaloids from Uncaria rhynchophylla (Miq.) Miq. ex Havil(UR) were selected as an example to show the advantage of this method. An optimized two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (3:7:1:9, v/v) was used in this study, where triethylamine (TEA) as the retainer and hydrochloric acid (HCl) as the eluter were added at the equimolar of 10mM. Crude alkaloids of UR dissolved in the corresponding upper phase (containing 10mM TEA) were extracted twice with lower phase (containing 10mM TEA) and lower phase (containing 10mM HCl), respectively, the second lower phase extract was subjected to pH-zone-refining CCC separation after alkalization and desalination. Finally, from 10g of crude alkaloids, 4g of refined alkaloids was obtained and the total content of seven target indole alkaloids was increased from 4.64% to 15.78%. Seven indole alkaloids, including 54mg isocorynoxeine, 21mg corynoxeine, 46mg isorhynchophylline, 35mg rhynchophylline, 65mg hirsutine, 51mg hirsuteine and 27mg geissoschizine methylether were all simultaneously separated from 2.5g of refined alkaloids, with the purity of 86.4%, 97.5%, 90.3%, 92.1%, 98.5%, 92.3%, and 92.8%, respectively. The total content and purities of the seven minor indole alkaloids were tested by HPLC and their chemical structures were elucidated by ESI-HRMS and (1)H NMR. Copyright © 2015 Elsevier B.V. All rights reserved.

Reductive dechlorination of chlorinated ethenes under oxidation-reduction conditions and potentiometric surfaces in two trichloroethene-contaminated zones at the Double Eagle and Fourth Street Superfund sites in Oklahoma City, Oklahoma

USGS Publications Warehouse

Braun, Christopher L.

2004-01-01

The Double Eagle Refining Superfund site and the Fourth Street Abandoned Refinery Superfund site are in northeast Oklahoma City, Oklahoma, adjacent to one another. The Double Eagle facility became a Superfund site on the basis of contamination from lead and volatile organic compounds; the Fourth Street facility on the basis of volatile organic compounds, pesticides, and acid-base neutral compounds. The study documented in this report was done to investigate whether reductive dechlorination of chlorinated ethenes under oxidation-reduction conditions is occurring in two zones of the Garber-Wellington aquifer (shallow zone 30–60 to 75 feet below land surface, deep zone 75 to 160 feet below land surface) at the sites; and to construct potentiometric surfaces of the two water-yielding zones to determine the directions of groundwater flow at the sites. The presence in some wells of intermediate products of reductive dechlorination, dichloroethene and vinyl chloride, is an indication that reductive dechlorination of trichloroethene is occurring. Dissolved oxygen concentrations (less than 0.5 milligram per liter) indicate that consumption of dissolved oxygen likely had occurred in the oxygen-reducing microbial process associated with reductive dechlorination. Concentrations of nitrate and nitrite nitrogen (generally less than 2.0 and 0.06 milligrams per liter, respectively) indicate that nitrate reduction probably is not a key process in either aquifer zone. Concentrations of ferrous iron greater than 1.00 milligram per liter in the majority of wells sampled indicate that iron reduction is probable. Concentrations of sulfide less than 0.05 milligram per liter in all wells indicate that sulfate reduction probably is not a key process in either zone. The presence of methane in ground water is an indication of strongly reducing conditions that facilitate reductive dechlorination. Methane was detected in all but one well. In the shallow zone in the eastern part of the study area, ground water flowing from the northwest and south coalesces in a potentiometric trough, then moves westward and ultimately northwestward. In the western part of the study area, ground water in the shallow zone flows northwest. In the deep zone in the eastern part of the study area, ground water generally flows northwestward; and in the western part of the study area, ground water in the deep zone generally flows northward.

Chemical variations within and between the clasts, and the matrix of the Abee enstatite chondrite suggest an impact-based differentiation mechanism

NASA Astrophysics Data System (ADS)

Higgins, Michael D.; Martin, Pierre-Etienne M. C.

2018-01-01

Abee is an enstatite chondrite breccia dominantly composed of kamacite, enstatite, silica, plagioclase, troilite and niningerite. Clasts are up to 220 mm long and vary in shape from angular to rounded. Some clasts are zoned with kamacite-enriched rims that follow the edge of the clast. Spatial compositional variations were examined in a small block to find out more about the petrological processes that produced this rock, particularly the relationship between the clasts, the matrix and the cores/rims of the zoned clasts. Compositional maps produced using a focussed-beam XRF were segmented into clasts and matrix, and rims and cores where possible. Compositions of most clasts, matrix and rim/cores define a simple, linear trend on simple variation diagrams. If it is assumed that all components were derived from an original homogeneous composition then the variation can be explained either by addition of kamacite or by loss of all other phases. Within this overall compositional variation the kamacite content generally increases as follows: matrix < large homogeneous clasts ≈ zoned clast cores < small homogeneous clasts ≈ zoned clast rims. Production of diversity by addition of kamacite to clasts and rim seems to require a complex history as the source cannot have been the current matrix. It is also difficult to produce the observed chemical variations and zoning by partial melting. However, differentiation by removal of all non-metallic phases may result from repeated impacts: Shock waves would deform kamacite whilst fracturing all other phases. The broken grains would then migrate towards the surface of the clasts where they would spall off into the matrix. This process would also lead to the observed rounding of some clasts. We propose that this shock-differentiation process be called 'smithing', as it resembles the ancient process of iron refining.

Iron catalyzed coal liquefaction process

DOEpatents

Garg, Diwakar; Givens, Edwin N.

1983-01-01

A process is described for the solvent refining of coal into a gas product, a liquid product and a normally solid dissolved product. Particulate coal and a unique co-catalyst system are suspended in a coal solvent and processed in a coal liquefaction reactor, preferably an ebullated bed reactor. The co-catalyst system comprises a combination of a stoichiometric excess of iron oxide and pyrite which reduce predominantly to active iron sulfide catalysts in the reaction zone. This catalyst system results in increased catalytic activity with attendant improved coal conversion and enhanced oil product distribution as well as reduced sulfide effluent. Iron oxide is used in a stoichiometric excess of that required to react with sulfur indigenous to the feed coal and that produced during reduction of the pyrite catalyst to iron sulfide.

CdZnTe substrate impurities and their effects on liquid phase epitaxy HgCdTe

NASA Astrophysics Data System (ADS)

Tower, J. P.; Tobin, S. P.; Kestigian, M.; Norton, P. W.; Bollong, A. B.; Schaake, H. F.; Ard, C. K.

1995-05-01

Impurity levels were tracked through the stages of substrate and liquid phase epitaxy (LPE) layer processing to identify sources of elements which degrade infrared photodetector performance. Chemical analysis by glow discharge mass spectrometry and Zeeman corrected graphite furnace atomic absorption effectively showed the levels of impurities introduced into CdZnTe substrate material from the raw materials and the crystal growth processes. A new purification process (in situ distillation zone refining) for raw materials was developed, resulting in improved CdZnTe substrate purity. Substrate copper contamination was found to degrade the LPE layer and device electrical properties, in the case of lightly doped HgCdTe. Anomalous HgCdTe carrier type conversion was correlated to certain CdZnTe and CdTe substrate ingots.

A New Paradigm for New Oceans

NASA Astrophysics Data System (ADS)

Foulger, G. R.; Doré, A. G.; Franke, D.; Geoffroy, L.; Gernigon, L.; Hole, M.; Hoskuldsson, A.; Julian, B. R.; Kusznir, N.; Martinez, F.; Natland, J. H.; Peace, A.; Petersen, K. D.; Schiffer, C.; Stephenson, R.; Stoker, M. S.

2017-12-01

The original simple theory of plate tectonics had to be refined to accommodate second-order geological features such as back-arc basins and continental deformation zones. We propose an additional refinement that is required by complexities that form and persist in new oceans when inhomogeneous continental lithosphere/tectosphere disintegrates. Such complexities include continual plate-boundary reorganizations and migrations, distributed continental material in the ocean, propagating and dying ridges, and sagging, flexing and tilting in the oceans and at continent-ocean boundary zones. Reorganizations of stress and motion persist, resulting in variable orientations over short distances, tectonic reactivations, complex plate boundary configurations including multiple triple junctions, and the formation and abandonment of oceanic microplates. Resulting local compressions and extensions are manifest as bathymetric anomalies, vertical motions, and distributed volcanism at various times and places as the new ocean grows. Examples of regions that exhibit some or all of these features include the North Atlantic, the Rio Grande Rise/Walvis Ridge region of the South Atlantic, and the Seychelles-Mauritius region in the Indian Ocean. We suggest that these complexities arise as a result of the formation of new spreading plate boundaries by rifts propagating through continental lithosphere/tectosphere that is anisotropic as a result of inherited structure/composition and/or a sub-lithospheric mantle destabilized by lithospheric-controlled processes. Such scenarios result in complicated disintegration of continents and local persistent dynamic instability in the new ocean.

A refined model for Kilauea's magma plumbing system

NASA Astrophysics Data System (ADS)

Poland, M. P.; Miklius, A.; Montgomery-Brown, E. D.

2011-12-01

Studies of the magma plumbing system of Kilauea have benefitted from the volcano's frequent eruptive activity, ease of access, and particularly the century-long observational record made possible by the Hawaiian Volcano Observatory. The explosion of geophysical data, especially seismic and geodetic, collected since the first model of Kilauea's magmatic system was published in 1960 allows for a detailed characterization of Kilauea's magma storage areas and transport pathways. Using geological, geochemical, and geophysical observations, we propose a detailed model of Kilauea's magma plumbing that we hope will provide a refined framework for studies of Kilauea's eruptive and intrusive activity. Kilauea's summit region is underlain by two persistently active, hydraulically linked magma storage areas. The larger reservoir is centered at ~3 km depth beneath the south caldera and is connected to Kilauea's two rift zones, which radiate from the summit to the east and southwest. All magma that enters the Kilauea edifice passes through this primary storage area before intrusion or eruption. During periods of increased magma storage at the summit, as was the case during 2003-2007, uplift may occur above temporary magma storage volumes, for instance, at the intersection of the summit and east rift zone at ~3 km depth, and within the southwest rift zone at ~2 km depth. The east rift zone is the longer and more active of Kilauea's two rift zones and apparently receives more magma from the summit. Small, isolated pods of magma exist within both rift zones, as indicated by deformation measurements, seismicity, petrologic data, and geothermal drilling results. These magma bodies are probably relicts of past intrusions and eruptions and can be highly differentiated. Within the deeper part of the rift zones, between about 3 km and 9 km depth, magma accumulation is hypothesized based on surface deformation indicative of deep rift opening. There is no direct evidence for magma within the deep rift zones, however, suggesting the possibility that the region is "dry" and that the opening deformation is accommodated by processes other than filling by magma. A smaller summit magma storage area is located at 1-2 km depth beneath the east margin of Halema'uma'u Crater, near the center of the caldera. The smaller reservoir is connected to, but perched above, the larger south caldera reservoir and rift zones, and therefore has more hydraulic head and drains rapidly during rift zone intrusions and eruptions. Secondary, shallow (~1 km depth) rift systems branch from this magma reservoir, as indicated by alignments of eruptive vents and fracture systems to the east and west from Halema'uma'u Crater. Although usually inactive, large historical eruptions have occurred from these rift systems, including Kilauea Iki in 1959 (east) and Mauna Iki in 1919-20 (west).

Parallel deterministic neutronics with AMR in 3D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clouse, C.; Ferguson, J.; Hendrickson, C.

1997-12-31

AMTRAN, a three dimensional Sn neutronics code with adaptive mesh refinement (AMR) has been parallelized over spatial domains and energy groups and runs on the Meiko CS-2 with MPI message passing. Block refined AMR is used with linear finite element representations for the fluxes, which allows for a straight forward interpretation of fluxes at block interfaces with zoning differences. The load balancing algorithm assumes 8 spatial domains, which minimizes idle time among processors.

Laser cladding assisted by friction stir processing for preparation of deformed crack-free Ni-Cr-Fe coating with nanostructure

NASA Astrophysics Data System (ADS)

Xie, Siyao; Li, Ruidi; Yuan, Tiechui; Chen, Chao; Zhou, Kechao; Song, Bo; Shi, Yusheng

2018-02-01

Although laser cladding has find its widespread application in surface hardening, this technology has been significantly limited by the solidification crack, which usually initiates along grain boundary due to the brittle precipitation in grain boundary and networks formation during the laser rapid melting/solidification process. This paper proposed a novel laser cladding technology assisted by friction stir processing (FSP) to eliminate the usual metallurgical defects by the thermomechanical coupling effect of FSP with the Ni-Cr-Fe as representative coating material. By the FSP assisted laser cladding, the crack in laser cladding Ni-Cr-Fe coating was eliminated and the coarse networks of laser cladding coating was transformed into dispersed nanoparticles. Moreover, the plastic layers with thicknesses 47-140 μm can be observed, with gradient grain refinement from substrate to the top surface in which grain size reached 300 nm and laser photocoagulation net second phase crushed in the layer. In addition, cracks closed in the plastic zone. The refinement of grain resulted the hardness increased to over 400 HV, much higher than the 300 HV of the laser cladding structure. After FSP, the friction coefficient decreased from 0.6167 to 0.5645 which promoted the wear resistance.

Volatiles in the Earth: All shallow and all recycled

NASA Technical Reports Server (NTRS)

Anderson, Don L.

1994-01-01

A case can be made that accretion of the Earth was a high-temperature process and that the primordial Earth was dry. A radial zone-refining process during accretion may have excluded low-melting point and volatile material, including large-ion lithophile elements toward the surface, leaving a refractory and zoned interior. Water, sediments and altered hydrous oceanic crust are introduced back into the interior by subduction, a process that may be more efficient today than in the past. Seismic tomography strongly suggests that a large part of the uppermantle is above the solidus, and this implies wet melting. The mantle beneath Archean cratons has very fast seismic velocities and appears to be strong to 150 km or greater. This is consistent with very dry mantle. It is argued that recycling of substantial quantities of water occurs in the shallow mantle but only minor amounts recycle to depths greater than 200 km. Recycling also oxidizes that mantle; ocean island ('hotspot') basalts are intermediate in oxidation state to island-arc and midocean ridge basalts (MORB). This suggests a deep uncontaminated reservoir for MORB. Plate tectonics on a dry Earth is discussed in order to focus attention on inconsistencies in current geochemical models of terrestrial evolution and recycling.

New insights into Mo and Ru isotope variation in the nebula and terrestrial planet accretionary genetics

NASA Astrophysics Data System (ADS)

Bermingham, K. R.; Worsham, E. A.; Walker, R. J.

2018-04-01

When corrected for the effects of cosmic ray exposure, Mo and Ru nucleosynthetic isotope anomalies in iron meteorites from at least nine different parent bodies are strongly correlated in a manner consistent with variable depletion in s-process nucleosynthetic components. In contrast to prior studies, the new results show no significant deviations from a single correlation trend. In the refined Mo-Ru cosmic correlation, a distinction between the non-carbonaceous (NC) group and carbonaceous chondrite (CC) group is evident. Members of the NC group are characterized by isotope compositions reflective of variable s-process depletion. Members of the CC group analyzed here plot in a tight cluster and have the most s-process depleted Mo and Ru isotopic compositions, with Mo isotopes also slightly enriched in r- and possibly p-process contributions. This indicates that the nebular feeding zone of the NC group parent bodies was characterized by Mo and Ru with variable s-process contributions, but with the two elements always mixed in the same proportions. The CC parent bodies sampled here, by contrast, were derived from a nebular feeding zone that had been mixed to a uniform s-process depleted Mo-Ru isotopic composition. Six molybdenite samples, four glacial diamictites, and two ocean island basalts were analyzed to provide a preliminary constraint on the average Mo isotope composition of the bulk silicate Earth (BSE). Combined results yield an average μ97Mo value of +3 ± 6. This value, coupled with a previously reported μ100Ru value of +1 ± 7 for the BSE, indicates that the isotopic composition of the BSE falls precisely on the refined Mo-Ru cosmic correlation. The overlap of the BSE with the correlation implies that there was homogeneous accretion of siderophile elements for the final accretion of 10 to 20 wt% of Earth's mass. The only known cosmochemical materials with an isotopic match to the BSE, with regard to Mo and Ru, are some members of the IAB iron meteorite complex and enstatite chondrites.

Long-Term Monitoring of Desert Land and Natural Resources and Application of Remote Sensing Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamada, Yuki; Rollins, Katherine E.

2016-11-01

Monitoring environmental impacts over large, remote desert regions for long periods of time can be very costly. Remote sensing technologies present a promising monitoring tool because they entail the collection of spatially contiguous data, automated processing, and streamlined data analysis. This report provides a summary of remote sensing products and refinement of remote sensing data interpretation methodologies that were generated as part of the U.S. Department of the Interior Bureau of Land Management Solar Energy Program. In March 2015, a team of researchers from Argonne National Laboratory (Argonne) collected field data of vegetation and surface types from more than 5,000more » survey points within the eastern part of the Riverside East Solar Energy Zone (SEZ). Using the field data, remote sensing products that were generated in 2014 using very high spatial resolution (VHSR; 15 cm) multispectral aerial images were validated in order to evaluate potential refinements to the previous methodologies to improve the information extraction accuracy.« less

Effect of Thermal History on Microstructures and Mechanical Properties of AZ31 Magnesium Alloy Prepared by Friction Stir Processing

PubMed Central

Chai, Fang; Zhang, Datong; Li, Yuanyuan

2014-01-01

Hot-rolled AZ31 (Mg-2.57Al-0.84Zn-0.32Mn, in mass percentage) magnesium alloy is subjected to friction stir processing in air (normal friction stir processing, NFSP) and under water (submerged friction stir processing, SFSP). Thermal history of the two FSP procedures is measured, and its effect on microstructures and mechanical properties of the experimental materials is investigated. Compared with NFSP, the peak temperature during SFSP is lower and the duration time at a high temperature is shorter due to the enhanced cooling effect of water. Consequently, SFSP results in further grain refinement, and the average grain size of the NFSP and SFSP specimens in the stir zone (SZ) are 2.9 μm and 1.3 μm, respectively. Transmission electron microscopy (TEM) examinations confirm that grain refinement is attributed to continuous dynamic recrystallization both for NFSP and SFSP. The average Vickers hardness in the SZ of the NFSP and SFSP AZ31 magnesium alloy are 76 HV and 87 HV. Furthermore, the ultimate tensile strength and the elongation of the SFSP specimen increase from 191 MPa and 31.3% in the NFSP specimen to 210 MPa and 50.5%, respectively. Both the NFSP and SFSP alloys fail through ductile fracture, but the dimples are much more obvious in the SFSP alloy. PMID:28788532

Optimization of Refining Craft for Vegetable Insulating Oil

NASA Astrophysics Data System (ADS)

Zhou, Zhu-Jun; Hu, Ting; Cheng, Lin; Tian, Kai; Wang, Xuan; Yang, Jun; Kong, Hai-Yang; Fang, Fu-Xin; Qian, Hang; Fu, Guang-Pan

2016-05-01

Vegetable insulating oil because of its environmental friendliness are considered as ideal material instead of mineral oil used for the insulation and the cooling of the transformer. The main steps of traditional refining process included alkali refining, bleaching and distillation. This kind of refining process used in small doses of insulating oil refining can get satisfactory effect, but can't be applied to the large capacity reaction kettle. This paper using rapeseed oil as crude oil, and the refining process has been optimized for large capacity reaction kettle. The optimized refining process increases the acid degumming process. The alkali compound adds the sodium silicate composition in the alkali refining process, and the ratio of each component is optimized. Add the amount of activated clay and activated carbon according to 10:1 proportion in the de-colorization process, which can effectively reduce the oil acid value and dielectric loss. Using vacuum pumping gas instead of distillation process can further reduce the acid value. Compared some part of the performance parameters of refined oil products with mineral insulating oil, the dielectric loss of vegetable insulating oil is still high and some measures are needed to take to further optimize in the future.

Modeling pH-zone refining countercurrent chromatography: a dynamic approach.

PubMed

Kotland, Alexis; Chollet, Sébastien; Autret, Jean-Marie; Diard, Catherine; Marchal, Luc; Renault, Jean-Hugues

2015-04-24

A model based on mass transfer resistances and acid-base equilibriums at the liquid-liquid interface was developed for the pH-zone refining mode when it is used in countercurrent chromatography (CCC). The binary separation of catharanthine and vindoline, two alkaloids used as starting material for the semi-synthesis of chemotherapy drugs, was chosen for the model validation. Toluene/CH3CN/water (4/1/5, v/v/v) was selected as biphasic solvent system. First, hydrodynamics and mass transfer were studied by using chemical tracers. Trypan blue only present in the aqueous phase allowed the determination of the parameters τextra and Pe for hydrodynamic characterization whereas acetone, which partitioned between the two phases, allowed the determination of the transfer parameter k0a. It was shown that mass transfer was improved by increasing both flow rate and rotational speed, which is consistent with the observed mobile phase dispersion. Then, the different transfer parameters of the model (i.e. the local transfer coefficient for the different species involved in the process) were determined by fitting experimental concentration profiles. The model accurately predicted both equilibrium and dynamics factors (i.e. local mass transfer coefficients and acid-base equilibrium constant) variation with the CCC operating conditions (cell number, flow rate, rotational speed and thus stationary phase retention). The initial hypotheses (the acid-base reactions occurs instantaneously at the interface and the process is mainly governed by mass transfer) are thus validated. Finally, the model was used as a tool for catharanthine and vindoline separation prediction in the whole experimental domain that corresponded to a flow rate between 20 and 60 mL/min and rotational speeds from 900 and 2100 rotation per minutes. Copyright © 2015 Elsevier B.V. All rights reserved.

Grain Refinement of Magnesium Alloys: A Review of Recent Research, Theoretical Developments, and Their Application

NASA Astrophysics Data System (ADS)

StJohn, D. H.; Easton, M. A.; Qian, M.; Taylor, J. A.

2013-07-01

This paper builds on the "Grain Refinement of Mg Alloys" published in 2005 and reviews the grain refinement research on Mg alloys that has been undertaken since then with an emphasis on the theoretical and analytical methods that have been developed. Consideration of recent research results and current theoretical knowledge has highlighted two important factors that affect an alloy's as-cast grain size. The first factor applies to commercial Mg-Al alloys where it is concluded that impurity and minor elements such as Fe and Mn have a substantially negative impact on grain size because, in combination with Al, intermetallic phases can be formed that tend to poison the more potent native or deliberately added nucleant particles present in the melt. This factor appears to explain the contradictory experimental outcomes reported in the literature and suggests that the search for a more potent and reliable grain refining technology may need to take a different approach. The second factor applies to all alloys and is related to the role of constitutional supercooling which, on the one hand, promotes grain nucleation and, on the other hand, forms a nucleation-free zone preventing further nucleation within this zone, consequently limiting the grain refinement achievable, particularly in low solute-containing alloys. Strategies to reduce the negative impact of these two factors are discussed. Further, the Interdependence model has been shown to apply to a broad range of casting methods from slow cooling gravity die casting to fast cooling high pressure die casting and dynamic methods such as ultrasonic treatment.

Trabecular trajectory in the articular processes of the human fourth cervical vertebra

PubMed Central

HERRERA, M.; PANCHÓN, A.; PEREZ-BACETE, M.

2001-01-01

The articular processes (AP) of the neural arch have been implicated in weight transmission through the cervical spine. To analyse the mechanism of weight transmission in the AP, we studied the direction of forces within it, in particular, the pattern of trabecular trajectories. Twenty-two AP from C4 vertebrae were studied in anatomical sections, and corresponding photoelastic models from selected sections were constructed and analysed. Anatomical and photoelastic findings show the subarticular spongiosa of the superior articular process (SAP) to be orthogonally arranged with vertical and oblique trabeculae in the direction of compressive forces and additional trabeculae always oriented perpendicular to the former. Vertical and oblique trabeculae are divided into rostral, middle and posterior groups. Rostral and middle trabeculae end in the anterior wall of the SAP and the transitional zone with the pedicle. Posterior trabeculae end in the subarticular spongiosa of the inferior articular process (IAP). The findings relating to trabecular trajectories in the SAP differ from previous descriptions and instead suggest that a part of the weight forces distributed within the AP transmit to the subchondral zone of the IAP. Knowledge of the trajectorial architecture of the AP may contribute to refining finite element analytical models for investigating its weight-bearing function. PMID:11554512

Numerical Simulation and Experimental Casting of Nickel-Based Single-Crystal Superalloys by HRS and LMC Directional Solidification Processes

NASA Astrophysics Data System (ADS)

Yan, Xuewei; Wang, Run'nan; Xu, Qingyan; Liu, Baicheng

2017-04-01

Mathematical models for dynamic heat radiation and convection boundary in directional solidification processes are established to simulate the temperature fields. Cellular automaton (CA) method and Kurz-Giovanola-Trivedi (KGT) growth model are used to describe nucleation and growth. Primary dendritic arm spacing (PDAS) and secondary dendritic arm spacing (SDAS) are calculated by the Ma-Sham (MS) and Furer-Wunderlin (FW) models respectively. The mushy zone shape is investigated based on the temperature fields, for both high-rate solidification (HRS) and liquid metal cooling (LMC) processes. The evolution of the microstructure and crystallographic orientation are analyzed by simulation and electron back-scattered diffraction (EBSD) technique, respectively. Comparison of the simulation results from PDAS and SDAS with experimental results reveals a good agreement with each other. The results show that LMC process can provide both dendritic refinement and superior performance for castings due to the increased cooling rate and thermal gradient.

Presence of Tungsten-Containing Fibers in Tungsten Refining and Manufacturing Processes

PubMed Central

Mckernan, John L.; Toraason, Mark A.; Fernback, Joseph E.; Petersen, Martin R.

2009-01-01

In tungsten refining and manufacturing processes, a series of tungsten oxides are typically formed as intermediates in the production of tungsten powder. The present study was conducted to characterize airborne tungsten-containing fiber dimensions, elemental composition and concentrations in the US tungsten refining and manufacturing industry. During the course of normal employee work activities, seven personal breathing zone and 62 area air samples were collected and analyzed using National Institute for Occupational Safety and Health (NIOSH) fiber sampling and counting methods to determine dimensions, composition and airborne concentrations of fibers. Mixed models were used to identify relationships between potential determinants and airborne fiber concentrations. Results from transmission electron microscopy analyses indicated that airborne fibers with length >0.5 μm, diameter >0.01 μm and aspect ratios ≥3:1 were present on 35 of the 69 air samples collected. Overall, the airborne fibers detected had a geometric mean length ≈3 μm and diameter ≈0.3 μm. Ninety-seven percent of the airborne fibers identified were in the thoracic fraction (i.e. aerodynamic diameter ≤ 10 μm). Energy dispersive X-ray spectrometry results indicated that airborne fibers prior to the carburization process consisted primarily of tungsten and oxygen, with other elements being detected in trace quantities. Based on NIOSH fiber counting ‘B’ rules (length > 5 μm, diameter < 3 μm and aspect ratio ≥ 5:1), airborne fiber concentrations ranged from below the limit of detection to 0.085 fibers cm−3, with calcining being associated with the highest airborne concentrations. The mixed model procedure indicated that process temperature had a marginally significant relationship to airborne fiber concentration. This finding was expected since heated processes such as calcining created the highest airborne fiber concentrations. The finding of airborne tungsten-containing fibers in this occupational setting needs to be confirmed in similar settings and demonstrates the need to obtain information on the durability and associated health effects of these fibers. PMID:19126624

An investigation into the mechanism for enhanced mechanical properties in friction stir welded AA2024-T3 joints coated with cold spraying

NASA Astrophysics Data System (ADS)

Li, N.; Li, W. Y.; Yang, X. W.; Feng, Y.; Vairis, A.

2018-05-01

Using cold spraying (CS), a surface layer with a modified microstructure and enhanced mechanical properties was formed on a 3.2 mm thick friction stir welded (FSWed) AA2024-T3 joint. The combined effect of "shot peening effect (SPE)" and "heat flow effect (HFE)" during CS were used to enhance joint mechanical properties. The microstructure evolution of the FSWed AA2024-T3 joints in the surface layer following CS coatings and their effect on mechanical properties were systematically characterized with electron back-scattered diffraction, transmission electron microscopy, differential scanning calorimetry and mechanical tests. Based on these experiments, a grain refinement, finer and more S phases, and improved amount of Guinier-Preston-Bagaryatsky (GPB) zones produced by CS treatments are proposed. The deposition of aluminum coating on the joint, lead to hardness recovery in the stir zone and the development of two low hardness zones as the density of GPB increased. The tensile properties of FSWed AA2024-T3 joints improved with the application of the aluminum coatings. Experiments and analysis of the enhanced mechanical properties mechanism indicate that SPE with a high plastic deformation and HFE with an intensive heat flow are necessary for the production of refined grains and increased numbers of GPB zones.

The Grain Structure of Castings: Some Aspects of Modelling

NASA Technical Reports Server (NTRS)

Hellawell, A.

1995-01-01

The efficacy of the modelling of the solidification of castings is typically tested against observed cooling curves and the final grain structures and sizes. Without thermo solutal convection, equiaxed grain formation is promoted by introduction of heterogeneous substrates into the melt, as grain refiners. With efficient thermo solutal convection, dendrite fragments from the mushy zone can act as an intrinsic source of equiaxed grains and resort to grain refining additions is unnecessary. The mechanisms of dendrite fragmentation and transport of these fragments are briefly considered.

Refining the structural framework of the Khimti Khola region, east-central Nepal Himalaya, using quartz textures and c-axis fabrics

NASA Astrophysics Data System (ADS)

Larson, Kyle P.

2018-02-01

New quartz texture and c-axis fabric data from across the Paleoproterozoic Ulleri-Phaplu-Melung orthogneiss in the Khimti Khola region of east central Nepal provide new constraints on the internal structural framework of the Himalaya that help shed light on the convergence accommodation processes active in the upper portion of the crust during orogenesis. These data outline a strain history that varies across the unit. Deformation near the base of the unit occurred at ∼605 (±50) °C with evidence of significant static recrystallization and recovery preserved in quartz, whereas deformation near the top of the unit occurred at ∼540 (±50) ˚C with quartz characterized by dynamic recrystallization mechanisms. The strength of the quartz c-axis fabrics follows a similar spatial pattern, with those from near the top of the unit recording stronger fabrics than those measured from lower in the unit. Together, these data are interpreted to indicate strain localization, possibly at progressively lower temperature, near the top of the Ulleri-Phaplu-Melung orthogneiss. This interpretation is consistent with cooling ages that indicate the upper boundary of the unit coincides with an out-of-sequence shear zone. This study not only provides a structural characterization of the shear zone, helping to refine the kinematic framework of this portion of the Himalaya, but also confirms the utility of fabric strength analysis in deciphering strain localization within pervasively deformed rocks.

Producing thin strips by twin-roll casting—part I: Process aspects and quality issues

NASA Astrophysics Data System (ADS)

Li, Ben Q.

1995-05-01

This two-part paper discusses recent advances in research and development for the direct production of coilable thin strips by twin-roll casting in both the aluminum and steel industries. While the former is empowering the casters to approach the theoretical productivity limit, the latter is striving to put pilot casters into commercial operation. These intensive R&D efforts are derived from the advantages, both economic and metallurgical, offered by the process. As twin-roll casting combines solidification and hot rolling into a single operation, the process requires low capital investment and low operational cost. Also, because of the high solidification rate attained in the process, the thin strips produced have a refined metallurgical structure, characterized by columnar and equiaxed zones with fine intermetallic particles. The enthusiasm about twin-roll casting is now being spread worldwide. This paper focuses on the process aspects and quality control of twin-roll casting. Part II, which will appear in the August issue, will review process modeling and pilot-plant development activities.

Microstructural variation through weld thickness and mechanical properties of peened friction stir welded 6061 aluminum alloy joints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdulstaar, Mustafa A., E-mail: mustafa.abdulstaar

The current study examined the effect of microstructure variation on the development of mechanical properties in friction stir welded joints of 6061-T6 aluminum alloy, which were subsequently processed by shot peening (SP). Following to FSW, fatigue specimens were extracted perpendicularly to the welding direction. Surface Skimming to 0.5 mm from crown and root sides of the joint was made and SP was later applied on the two sides using ceramic shots of two different Almen intensities of 0.18 mmA and 0.24 mmA. Microstructural examination by electron back scattered diffraction (EBSD) indicated variation in the grain refinement of the weld zone,more » with coarsest grains (5 μm) at the crown side and finest grains (2 μm) at the root side. Reduction of microhardness to 60 HV occurred in the weld zone for samples in FSW condition. Application of SP promoted significant strain hardening at the crown side, with Almen intensities of 0.24 mmA providing maximum increase in microhardness to 120 HV. On the contrary, only a maximum microhardness of 75 HV was obtained at the root side. The difference in strain hardening capability at the two sides was strongly dependent on grain size. The two Almen intensities produced similar distribution of compressive residual stresses in the subsurface regions that led to enhance the fatigue strength to the level of base metal for N ≥ 10{sup 5} cycles. Yet, the increase in fatigue strength was more pronounced with increasing Almen intensity to 0.24 mmA, demonstrating further enhancement by strain hardening. - Highlights: • Grain refinement was observed after friction stir welding of AA 6061-T6. • Reduction in microhardness and fatigue strength were obtained after welding. • Variation in grain refinement led to different hardening behavior after peening. • Shot peening induced beneficial compressive residual stresses. • Shot peening and surface skimming markedly improved the fatigue performance.« less

Simulation of the shallow groundwater-flow system near the Hayward Airport, Sawyer County, Wisconsin

USGS Publications Warehouse

Hunt, Randall J.; Juckem, Paul F.; Dunning, Charles P.

2010-01-01

There are concerns that removal and trimming of vegetation during expansion of the Hayward Airport in Sawyer County, Wisconsin, could appreciably change the character of a nearby cold-water stream and its adjacent environs. In cooperation with the Wisconsin Department of Transportation, a two-dimensional, steady-state groundwater-flow model of the shallow groundwater-flow system near the Hayward Airport was refined from a regional model of the area. The parameter-estimation code PEST was used to obtain a best fit of the model to additional field data collected in February 2007 as part of this study. The additional data were collected during an extended period of low runoff and consisted of water levels and streamflows near the Hayward Airport. Refinements to the regional model included one additional hydraulic-conductivity zone for the airport area, and three additional parameters for streambed resistance in a northern tributary to the Namekagon River and in the main stem of the Namekagon River. In the refined Hayward Airport area model, the calibrated hydraulic conductivity was 11.2 feet per day, which is within the 58.2 to 7.9 feet per day range reported for the regional glacial and sandstone aquifer, and is consistent with a silty soil texture for the area. The calibrated refined model had a best fit of 8.6 days for the streambed resistance of the Namekagon River and between 0.6 and 1.6 days for the northern tributary stream. The previously reported regional groundwater-recharge rate of 10.1 inches per year was adjusted during calibration of the refined model in order to match streamflows measured during the period of extended low runoff; this resulted in an optimal groundwater-recharge rate of 7.1 inches per year during this period. The refined model was then used to simulate the capture zone of the northern tributary to the Namekagon River.

Grain Refinement of AZ31 Magnesium Alloy Weldments by AC Pulsing Technique

NASA Astrophysics Data System (ADS)

Kishore Babu, N.; Cross, C. E.

2012-11-01

The current study has investigated the influence of alternating current pulsing on the structure and mechanical properties of AZ31 magnesium alloy gas tungsten arc (GTA) weldments. Autogenous full penetration bead-on-plate GTA welds were made under a variety of conditions including variable polarity (VP), variable polarity mixed (VPM), alternating current (AC), and alternating current pulsing (ACPC). AC pulsing resulted in significant refinement of weld metal when compared with the unpulsed conditions. AC pulsing leads to relatively finer and more equiaxed grain structure in GTA welds. In contrast, VP, VPM, and AC welding resulted in predominantly columnar grain structures. The reason for this grain refinement may be attributed to the periodic variations in temperature gradient and solidification rate associated with pulsing as well as weld pool oscillation observed in the ACPC welds. The observed grain refinement was shown to result in an appreciable increase in fusion zone hardness, tensile strength, and ductility.

Fabrication of thick multilayered steel structure using A516 Grade 70 by multipass friction stir welding †

DOE PAGES

Lim, Y. C.; Sanderson, S.; Mahoney, M.; ...

2016-04-06

Here, we fabricated a thick-sectioned multilayered steel structure by multipass friction stir welding on A516 Grade 70 steel. Tensile strength of the multilayered samples was comparable to that of the base metal. Failure was located in the base metal when a defect-free sample was tested. Charpy impact toughness was higher in the stir zone and heat affected zone than in the base metal. For higher microhardness values were found in the stir zone and heat affected zone than the base metal due to grain refinement and modification of the microstructures. As a result, improved mechanical properties compared to the basemore » metal were found in the weld zones of friction stir welded A516 Grade 70 steel.« less

PH-zone-refining counter-current chromatography with a hydrophilic organic/salt-containing two-phase solvent system for preparative separation of polar alkaloids from natural products.

PubMed

Zou, Denglang; Du, Yurong; Kuang, Jianyuan; Sun, Shihao; Ma, Jianbin; Jiang, Renwang

2018-06-08

This study presents an efficient strategy based on pH-zone-refining counter-current chromatography with a hydrophilic organic/salt-containing two-phase system composed of acetonitrile, sodium chloride and water for preparative separation of polar alkaloids from natural products. Acetonitrile-sodium chloride-water system provides a wider range of polarity for polar alkaloids than classical aqueous two-phase systems. It gets rid of the effect of free hydrogen ion, strong ionic strength, hold low viscosity and the sharp retainer border could be formed easily. So acetonitrile-sodium chloride-water system showed great advantages to pH-zone-refining counter-current chromatography for polar alkaloids. The separation of polar indole alkaloids from toad venom was selected as an example to show the advantage and practicability of this strategy. An optimized acetonitrile-sodium chloride-water (54%:5%:41%, w%) system was applied in this study, where 10 mM triethylamine (TEA) as the retainer and 15 mM hydrochloric acid (HCl) as the eluter were added. As a result, three polar indole alkaloids, including 19 mg of serotonin, 45 mg of 5-Hydroxy-N'-methyl tryptamine, 33 mg of bufotenine were simultaneously separated from 500 mg of 5% ethanol elution fraction of toad venom on macroporous resin chromatography, with the purity of 91.3%, 97.5% and 89.4%, respectively. Their structures were identified by spectroscopic analysis. Copyright © 2018 Elsevier B.V. All rights reserved.

At-sea detection of marine debris: overview of technologies, processes, issues, and options.

PubMed

Mace, Thomas H

2012-01-01

At-sea detection of marine debris presents a difficult problem, as the debris items are often relatively small and partially submerged. However, they may accumulate in water parcel boundaries or eddy lines. The application of models, satellite radar and multispectral data, and airborne remote sensing (particularly radar) to focus the search on eddies and convergence zones in the open ocean appear to be a productive avenue of investigation. A multistage modeling and remote sensing approach is proposed for the identification of areas of the open ocean where debris items are more likely to congregate. A path forward may best be achieved through the refinement of the Ghost Net procedures with the addition of a final search stage using airborne radar from an UAS simulator aircraft to detect zones of potential accumulation for direct search. Sampling strategies, direct versus indirect measurements, remote sensing resolution, sensor/platform considerations, and future state are addressed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Laser Cladding of Ti-6Al-4 V Powder on Ti-6Al-4 V Substrate: Effect of Laser Cladding Parameters on Microstructure

NASA Astrophysics Data System (ADS)

Cottam, Ryan; Brandt, Milan

The laser cladding of Ti-6Al-4 V powder on Ti-6Al-4 V substrate has been investigated to determine laser parameters that could be used as a repair technology for Ti-6Al-4 V components. The parameters chosen for the investigation were developed by an analytical laser cladding model. Holding clad height and melt pool depth constant, the traversing speed was varied between 300 mm/min and 1500 mm/min, an associated power for the given speed was calculated by the model. Two different melt pool depths were used in the calculation of laser power for a given process velocity. The resulting microstructures in the clad zone varied from a relatively thin martensitic structure to a dendritic/thick martensitic structure. The heat affected zone (HAZ) showed a refinement of the Widmanstatten microstructure with a decreasing laser traversing speed and a coarser martensitic structure for the sample prepared with a deeper melt pool.

Evaluation of deep vadose zone contaminant flux into groundwater: Approach and case study

NASA Astrophysics Data System (ADS)

Oostrom, M.; Truex, M. J.; Last, G. V.; Strickland, C. E.; Tartakovsky, G. D.

2016-06-01

For sites with a contaminant source located in the vadose zone, the nature and extent of groundwater contaminant plumes are a function of the contaminant flux from the vadose zone to groundwater. Especially for thick vadose zones, transport may be relatively slow making it difficult to directly measure contaminant flux. An integrated assessment approach, supported by site characterization and monitoring data, is presented to explain current vadose zone contaminant distributions and to estimate future contaminant flux to groundwater in support of remediation decisions. The U.S. Department of Energy Hanford Site (WA, USA) SX Tank Farm was used as a case study because of a large existing contaminant inventory in its deep vadose zone, the presence of a limited-extent groundwater plume, and the relatively large amount of available data for the site. A predictive quantitative analysis was applied to refine a baseline conceptual model through the completion of a series of targeted simulations. The analysis revealed that site recharge is the most important flux-controlling process for future contaminant flux. Tank leak characteristics and subsurface heterogeneities appear to have a limited effect on long-term contaminant flux into groundwater. The occurrence of the current technetium-99 groundwater plume was explained by taking into account a considerable historical water-line leak adjacent to one of the tanks. The analysis further indicates that the vast majority of technetium-99 is expected to migrate into the groundwater during the next century. The approach provides a template for use in evaluating contaminant flux to groundwater using existing site data and has elements that are relevant to other disposal sites with a thick vadose zone.

Evaluation of deep vadose zone contaminant flux into groundwater: Approach and case study.

PubMed

Oostrom, M; Truex, M J; Last, G V; Strickland, C E; Tartakovsky, G D

2016-06-01

For sites with a contaminant source located in the vadose zone, the nature and extent of groundwater contaminant plumes are a function of the contaminant flux from the vadose zone to groundwater. Especially for thick vadose zones, transport may be relatively slow making it difficult to directly measure contaminant flux. An integrated assessment approach, supported by site characterization and monitoring data, is presented to explain current vadose zone contaminant distributions and to estimate future contaminant flux to groundwater in support of remediation decisions. The U.S. Department of Energy Hanford Site (WA, USA) SX Tank Farm was used as a case study because of a large existing contaminant inventory in its deep vadose zone, the presence of a limited-extent groundwater plume, and the relatively large amount of available data for the site. A predictive quantitative analysis was applied to refine a baseline conceptual model through the completion of a series of targeted simulations. The analysis revealed that site recharge is the most important flux-controlling process for future contaminant flux. Tank leak characteristics and subsurface heterogeneities appear to have a limited effect on long-term contaminant flux into groundwater. The occurrence of the current technetium-99 groundwater plume was explained by taking into account a considerable historical water-line leak adjacent to one of the tanks. The analysis further indicates that the vast majority of technetium-99 is expected to migrate into the groundwater during the next century. The approach provides a template for use in evaluating contaminant flux to groundwater using existing site data and has elements that are relevant to other disposal sites with a thick vadose zone. Copyright © 2016 Elsevier B.V. All rights reserved.

Evaluation of Deep Vadose Zone Contaminant Flux into Groundwater: Approach and Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oostrom, Martinus; Truex, Michael J.; Last, George V.

For sites with a contaminant source located in the vadose zone, the nature and extent of groundwater contaminant plumes are a function of the contaminant flux from the vadose zone to groundwater. Especially for thick vadose zones, transport may be relatively slow making it difficult to directly measure contaminant flux. An integrated assessment approach, supported by site characterization and monitoring data, is presented to explain current vadose zone contaminant distributions and to estimate future contaminant flux to groundwater in support of remediation decisions. The U.S. Department of Energy Hanford Site (WA, USA) SX Tank Farm was used as a casemore » study because of a large existing contaminant inventory in its deep vadose zone, the presence of a limited-extent groundwater plume, and the relatively large amount of available data for the site. A predictive quantitative analysis was applied to refine a baseline conceptual model through the completion of a series of targeted simulations. The analysis revealed that site recharge is the most important flux-controlling process for future contaminant flux. Tank leak characteristics and subsurface heterogeneities appear to have a limited effect on long-term contaminant flux into groundwater. The occurrence of the current technetium-99 groundwater plume was explained by taking into account a considerable historical water-line leak adjacent to one of the tanks. The analysis further indicates that the vast majority of technetium-99 is expected to migrate into the groundwater during the next century. The approach provides a template for use in evaluating contaminant flux to groundwater using existing site data and has elements that are relevant to other disposal sites with a thick vadose zone.« less

76 FR 10329 - Foreign-Trade Zone 3-San Francisco, California; Application for Subzone; Valero Refining Company...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-24

... Pier 95, near the Benicia-Martinez Bridge, Benicia. The refinery is used to produce fuels and other petroleum products. Products include gasoline, diesel, jet fuel, propane, butane, fuel oil, residual oil...

Microstructure and Tensile Properties of Friction Stir Processed Mg–Sn–Zn Alloy

PubMed Central

Chen, Xiaoyang; Dai, Qiao; Li, Xingcheng; Lu, Yalin; Zhang, Yang

2018-01-01

In this study, as-cast Mg–6Sn–2Zn (wt.%) alloy was subjected to friction stir processing (FSP) and the microstructure and tensile properties of FSP Mg–6Sn–2Zn samples were investigated. It was found that, in the stir zone (SZ) of FSP Mg–6Sn–2Zn samples, α-Mg grains were significantly refined via dynamic recrystallization (DRX) and the Mg2Sn phase was broken and partially dissolved. The microstructure in SZ was nonuniform and DRXed grains in the SZ-up regions were coarser than those in the SZ-down regions. Coarse broken Mg2Sn particles were observed in the SZ-up regions, while only fine Mg2Sn particles were observed in the SZ-down regions. Strong {0001} basal texture developed in the SZ regions of Mg–6Sn–2Zn samples after FSP. The increase of travel speed had little effect on the texture of different SZ regions. The ductility of FSP Mg–6Sn–2Zn samples was obviously improved, while the improvement in strength was negligible when compared to the as-cast sample. The tensile properties of FSP Mg–6Sn–2Zn samples were influenced by grain refinement, texture modification, and the breaking up and dissolution of the Mg2Sn phase. PMID:29690590

Microstructure and Tensile Properties of Friction Stir Processed Mg⁻Sn⁻Zn Alloy.

PubMed

Chen, Xiaoyang; Dai, Qiao; Li, Xingcheng; Lu, Yalin; Zhang, Yang

2018-04-23

In this study, as-cast Mg⁻6Sn⁻2Zn (wt.%) alloy was subjected to friction stir processing (FSP) and the microstructure and tensile properties of FSP Mg⁻6Sn⁻2Zn samples were investigated. It was found that, in the stir zone (SZ) of FSP Mg⁻6Sn⁻2Zn samples, α-Mg grains were significantly refined via dynamic recrystallization (DRX) and the Mg₂Sn phase was broken and partially dissolved. The microstructure in SZ was nonuniform and DRXed grains in the SZ-up regions were coarser than those in the SZ-down regions. Coarse broken Mg₂Sn particles were observed in the SZ-up regions, while only fine Mg₂Sn particles were observed in the SZ-down regions. Strong {0001} basal texture developed in the SZ regions of Mg⁻6Sn⁻2Zn samples after FSP. The increase of travel speed had little effect on the texture of different SZ regions. The ductility of FSP Mg⁻6Sn⁻2Zn samples was obviously improved, while the improvement in strength was negligible when compared to the as-cast sample. The tensile properties of FSP Mg⁻6Sn⁻2Zn samples were influenced by grain refinement, texture modification, and the breaking up and dissolution of the Mg₂Sn phase.

Human Lymphoid Translocation Fragile Zones Are Hypomethylated and Have Accessible Chromatin

PubMed Central

Lu, Zhengfei; Tsai, Albert G.; Pardo, Carolina E.; Müschen, Markus; Kladde, Michael P.

2015-01-01

Chromosomal translocations are a hallmark of hematopoietic malignancies. CG motifs within translocation fragile zones (typically 20 to 600 bp in size) are prone to chromosomal translocation in lymphomas. Here we demonstrate that the CG motifs in human translocation fragile zones are hypomethylated relative to the adjacent DNA. Using a methyltransferase footprinting assay on isolated nuclei (in vitro), we find that the chromatin at these fragile zones is accessible. We also examined in vivo accessibility using cellular expression of a prokaryotic methylase. Based on this assay, which measures accessibility over a much longer time interval than is possible with in vitro methods, these fragile zones were found to be more accessible than the adjacent DNA. Because DNA within the fragile zones can be methylated by both cellular and exogenous methyltransferases, the fragile zones are predominantly in a duplex DNA conformation. These observations permit more-refined models for why these zones are 100- to 1,000-fold more prone to undergo chromosomal translocation than the adjacent regions. PMID:25624348

Composite-Grid Techniques and Adaptive Mesh Refinement in Computational Fluid Dynamics

DTIC Science & Technology

1990-01-01

years of hard work. During that period an estimated 410 gallons of strong coffee has flowed under the bridge. It has been with the support of this...thank Peter James Coffee Company for the continuous supply of Vienna Roast . I should also thank my advisor, Joel Ferziger, for getting me started on my...variation confined to some rather narrow zones in the field. These zones (boundary layers, shocks, etc.) cause problems during numerical solution of

Process for solvent refining of coal using a denitrogenated and dephenolated solvent

DOEpatents

Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

1984-01-01

A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

Optimization of palm oil physical refining process for reduction of 3-monochloropropane-1,2-diol (3-MCPD) ester formation.

PubMed

Zulkurnain, Musfirah; Lai, Oi Ming; Tan, Soo Choon; Abdul Latip, Razam; Tan, Chin Ping

2013-04-03

The reduction of 3-monochloropropane-1,2-diol (3-MCPD) ester formation in refined palm oil was achieved by incorporation of additional processing steps in the physical refining process to remove chloroester precursors prior to the deodorization step. The modified refining process was optimized for the least 3-MCPD ester formation and acceptable refined palm oil quality using response surface methodology (RSM) with five processing parameters: water dosage, phosphoric acid dosage, degumming temperature, activated clay dosage, and deodorization temperature. The removal of chloroester precursors was largely accomplished by increasing the water dosage, while the reduction of 3-MCPD esters was a compromise in oxidative stability and color of the refined palm oil because some factors such as acid dosage, degumming temperature, and deodorization temperature showed contradictory effects. The optimization resulted in 87.2% reduction of 3-MCPD esters from 2.9 mg/kg in the conventional refining process to 0.4 mg/kg, with color and oil stability index values of 2.4 R and 14.3 h, respectively.

Comparison of oil refining and biodiesel production process between screw press and n-hexane techniques from beauty leaf feedstock

NASA Astrophysics Data System (ADS)

Bhuiya, M. M. K.; Rasul, M. G.; Khan, M. M. K.; Ashwath, N.

2016-07-01

The Beauty Leaf Tree (Callophylum inophyllum) is regarded as an alternative source of energy to produce 2nd generation biodiesel due to its potentiality as well as high oil yield content in the seed kernels. The treating process is indispensable during the biodiesel production process because it can augment the yield as well as quality of the product. Oil extracted from both mechanical screw press and solvent extraction using n-hexane was refined. Five replications each of 25 gm of crude oil for screw press and five replications each of 25 gm of crude oil for n-hexane were selected for refining as well as biodiesel conversion processes. The oil refining processes consists of degumming, neutralization as well as dewaxing. The degumming, neutralization and dewaxing processes were performed to remove all the gums (phosphorous-based compounds), free fatty acids, and waxes from the fresh crude oil before the biodiesel conversion process carried out, respectively. The results indicated that up to 73% and 81% of mass conversion efficiency of the refined oil in the screw press and n-hexane refining processes were obtained, respectively. It was also found that up to 88% and 90% of biodiesel were yielded in terms of mass conversion efficiency in the transesterification process for the screw press and n-hexane techniques, respectively. While the entire processes (refining and transesterification) were considered, the conversion of beauty leaf tree (BLT) refined oil into biodiesel was yielded up to 65% and 73% of mass conversion efficiency for the screw press and n-hexane techniques, respectively. Physico-chemical properties of crude and refined oil, and biodiesel were characterized according to the ASTM standards. Overall, BLT has the potential to contribute as an alternative energy source because of high mass conversion efficiency.

Solid-state combustion synthesis of ceramics and alloys in reduced gravity

NASA Technical Reports Server (NTRS)

Valone, S. M.; Behrens, R. G.

1988-01-01

Possible microgravity effects are explored in the combustion synthesis of ceramics and alloys from their constituent elements. Molten intermediates are typically present during the combustion process, thereby offering the chance for natural convection to take place. Numerical simulations suggest that the combustion front in concert with gravity may act as a partial zone-refinement mechanism which is attempting to sweep out porosity in the sample. Contrary to suggestions by dimensional analysis, no effects on the combustion rate are seen. An analytical model of the combustion velocity as a function of the gravitational field and the spreading rate of molten material gives the correct order of magnitude of the gravity effect as measured by centrifuge experiments.

Magnesium Recycling of Partially Oxidized, Mixed Magnesium-Aluminum Scrap through Combined Refining and Solid Oxide Membrane Electrolysis Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiaofei Guan; Peter A. Zink; Uday B. Pal

2012-01-01

Pure magnesium (Mg) is recycled from 19g of partially oxidized 50.5wt.% Mg-Aluminum (Al) alloy. During the refining process, potentiodynamic scans (PDS) were performed to determine the electrorefining potential for magnesium. The PDS show that the electrorefining potential increases over time as the magnesium content inside the Mg-Al scrap decreases. Up to 100% percent of magnesium is refined from the Mg-Al scrap by a novel refining process of dissolving magnesium and its oxide into a flux followed by vapor phase removal of dissolved magnesium and subsequently condensing the magnesium vapor. The solid oxide membrane (SOM) electrolysis process is employed in themore » refining system to enable additional recycling of magnesium from magnesium oxide (MgO) in the partially oxidized Mg-Al scrap. The combination of the refining and SOM processes yields 7.4g of pure magnesium.« less

Functional Zonation of the Adult Mammalian Adrenal Cortex

PubMed Central

Vinson, Gavin P.

2016-01-01

The standard model of adrenocortical zonation holds that the three main zones, glomerulosa, fasciculata, and reticularis each have a distinct function, producing mineralocorticoids (in fact just aldosterone), glucocorticoids, and androgens respectively. Moreover, each zone has its specific mechanism of regulation, though ACTH has actions throughout. Finally, the cells of the cortex originate from a stem cell population in the outer cortex or capsule, and migrate centripetally, changing their phenotype as they progress through the zones. Recent progress in understanding the development of the gland and the distribution of steroidogenic enzymes, trophic hormone receptors, and other factors suggests that this model needs refinement. Firstly, proliferation can take place throughout the gland, and although the stem cells are certainly located in the periphery, zonal replenishment can take place within zones. Perhaps more importantly, neither the distribution of enzymes nor receptors suggest that the individual zones are necessarily autonomous in their production of steroid. This is particularly true of the glomerulosa, which does not seem to have the full suite of enzymes required for aldosterone biosynthesis. Nor, in the rat anyway, does it express MC2R to account for the response of aldosterone to ACTH. It is known that in development, recruitment of stem cells is stimulated by signals from within the glomerulosa. Furthermore, throughout the cortex local regulatory factors, including cytokines, catecholamines and the tissue renin-angiotensin system, modify and refine the effects of the systemic trophic factors. In these and other ways it more and more appears that the functions of the gland should be viewed as an integrated whole, greater than the sum of its component parts. PMID:27378832

Optimization of Melt Treatment for Austenitic Steel Grain Refinement

NASA Astrophysics Data System (ADS)

Lekakh, Simon N.; Ge, Jun; Richards, Von; O'Malley, Ron; TerBush, Jessica R.

2017-02-01

Refinement of the as-cast grain structure of austenitic steels requires the presence of active solid nuclei during solidification. These nuclei can be formed in situ in the liquid alloy by promoting reactions between transition metals (Ti, Zr, Nb, and Hf) and metalloid elements (C, S, O, and N) dissolved in the melt. Using thermodynamic simulations, experiments were designed to evaluate the effectiveness of a predicted sequence of reactions targeted to form precipitates that could act as active nuclei for grain refinement in austenitic steel castings. Melt additions performed to promote the sequential precipitation of titanium nitride (TiN) onto previously formed spinel (Al2MgO4) inclusions in the melt resulted in a significant refinement of the as-cast grain structure in heavy section Cr-Ni-Mo stainless steel castings. A refined as-cast structure consisting of an inner fine-equiaxed grain structure and outer columnar dendrite zone structure of limited length was achieved in experimental castings. The sequential of precipitation of TiN onto Al2MgO4 was confirmed using automated SEM/EDX and TEM analyses.

Morphology and topography study of graphene synthesized from plant oil

NASA Astrophysics Data System (ADS)

Robaiah, M.; Rusop, M.; Abdullah, S.; Khusaimi, Z.; Azhan, H.; Laila, M. O.; Salifairus, M. J.; Asli, N. A.

2018-05-01

The graphene is material consists of bonded atom carbon atoms in sheet form one atom thick. The different types of carbon sources which are refined corn oil, palm oil and waste cooking palm oil were used as carbon feedstock to supply carbon atom for synthesizing graphene on the nickel substrate by thermal chemical vapour deposition. The substrate and carbon sources were placed in double zone furnaces. The carbon sources and the substrate were heated at 300 °C and 900 °C respectively. The both furnaces were switched off after synthesis time for cooling process finish. The formation of the graphene on the Ni surface appears due to segregation and precipitation of a high amount of carbon from the source material during the cooling process. FESEM, AFM, UV-VIS Spectroscopy and Raman Spectroscopy were used to characterize and synthesized graphene.

Friction Stir Back Extrusion of Aluminium Alloys for Automotive Applications

NASA Astrophysics Data System (ADS)

Xu, Zeren

Since the invention of Friction Stir Welding in 1991 as a solid state joining technique, extensive scientific investigations have been carried out to understand fundamental aspects of material behaviors when processed by this technique, in order to optimize processing conditions as well as mechanical properties of the welds. Based on the basic principles of Friction Stir Welding, several derivatives have also been developed such as Friction Stir Processing, Friction Extrusion and Friction Stir Back Extrusion. Friction Stir Back Extrusion is a novel technique that is proposed recently and designed for fabricating tubes from lightweight alloys. Some preliminary results have been reported regarding microstructure and mechanical properties of Friction Stir Back Extrusion processed AZ31 magnesium alloy, however, systematic study and in-depth investigations are still needed to understand the materials behaviors and underlying mechanisms when subjected to Friction Stir Back Extrusion, especially for age-hardenable Al alloys. In the present study, Friction Stir Back Extrusion processed AA6063-T5 and AA7075-T6 alloys are analyzed with respect to grain structure evolution, micro-texture change, recrystallization mechanisms, precipitation sequence as well as mechanical properties. Optical Microscopy, Electron Backscatter Diffraction, Transmission Electron Microscopy, Vickers Hardness measurements and uniaxial tensile tests are carried out to characterize the microstructural change as well as micro and macro mechanical properties of the processed tubes. Special attention is paid to the micro-texture evolution across the entire tube and dynamic recrystallization mechanisms that are responsible for grain refinement. Significant grain refinement has been observed near the processing zone while the tube wall is characterized by inhomogeneous grain structure across the thickness for both alloys. Dissolution of existing precipitates is noticed under the thermal hysterias imposed by Friction Stir Back Extrusion process, resulting in decreased strength but improved elongation of the processed tubes; a post-process aging step can effectively restore the mechanical properties of the processed tubes by allowing for the reprecipitation of solute elements in the form of fine, dispersed precipitates. Texture analysis performed for AA6063 alloy suggests the dominance of simple shear type textures with clear transition from initial texture to stable B/ ?B components via intermediate types that are stable under moderate strain levels. In order to identify the texture components properly, rigid body rotations are applied to the existing coordinate system to align it to local shear reference frame. Surprisingly, for AA7075 tubes, and fibers are observed to be the dominant texture components in the transition region as well as thermomechanically affected zone while the processing zone is characterized by random texture. The underlying mechanisms responsible for the formation of random texture are discussed in Chapter 5 based on Electron Backscatter Diffraction analysis. Comparative discussions are also carried out for the recrystallization mechanisms that are responsible for grain structure evolution of both alloys. Continuous grain subdivision and reorientation is cited as the dominant mechanism for the recrystallization of AA6063 alloys, while dynamic recrystallization occurs mainly in the form of Geometric Dynamic Recrystallization and progressive subgrain rotations near grain boundaries in AA7075 alloys.

Subduction, Extension, and a Mantle Plume in the Pacific Northwest

NASA Astrophysics Data System (ADS)

Hawley, W. B.; Allen, R. M.; Richards, M. A.

2016-12-01

Subduction zones are some of the most important systems that control the dynamics and evolution of the earth. The Cascadia Subduction Zone offers a unique natural laboratory for understanding the subduction process, and how subduction interacts with other large-scale geodynamical phenomena. The small size of the Juan de Fuca (JdF) plate and the proximity of the system to the Yellowstone Hotspot and the extensional Basin and Range province allow for detailed study of the effects these important systems have on each other. We present both a P-wave and an S-wave tomographic model of the Pacific Northwestern United States using regional seismic arrays, including the amphibious Cascadia Initiative. These models share important features, such as the Yellowstone plume, the subducting JdF slab, a gap in the subducting slab, and a low-velocity feature beneath the shallowest portions of the slab. But subtle differences in these features between the models—the size of the gap in the subducting JdF slab and the shape of the Yellowstone plume shaft above the transition zone, for example—provide physical insight into the interpretation of these models. The physics that we infer from our seismic tomography and other studies of the region will refine our understanding of subduction zones worldwide, and will help to identify targets for future amphibious seismic array studies. The discovery of a pronounced low-velocity feature beneath the JdF slab as it subducts beneath the coastal Pacific Northwest is, thus far, the most surprising result from our imaging work, and implies a heretofore unanticipated regime of dynamical interaction between the sublithospheric oceanic asthenosphere and the subduction process. Such discoveries are made possible, and rendered interpretable, by ever-increasing resolution that the Cascadia Initiative affords seismic tomography models.

Performance of a process-based hydrodynamic model in predicting shoreline change

NASA Astrophysics Data System (ADS)

Safak, I.; Warner, J. C.; List, J. H.

2012-12-01

Shoreline change is controlled by a complex combination of processes that include waves, currents, sediment characteristics and availability, geologic framework, human interventions, and sea level rise. A comprehensive data set of shoreline position (14 shorelines between 1978-2002) along the continuous and relatively non-interrupted North Carolina Coast from Oregon Inlet to Cape Hatteras (65 km) reveals a spatial pattern of alternating erosion and accretion, with an erosional average shoreline change rate of -1.6 m/yr and up to -8 m/yr in some locations. This data set gives a unique opportunity to study long-term shoreline change in an area hit by frequent storm events while relatively uninfluenced by human interventions and the effects of tidal inlets. Accurate predictions of long-term shoreline change may require a model that accurately resolves surf zone processes and sediment transport patterns. Conventional methods for predicting shoreline change such as one-line models and regression of shoreline positions have been designed for computational efficiency. These methods, however, not only have several underlying restrictions (validity for small angle of wave approach, assuming bottom contours and shoreline to be parallel, depth of closure, etc.) but also their empirical estimates of sediment transport rates in the surf zone have been shown to vary greatly from the calculations of process-based hydrodynamic models. We focus on hind-casting long-term shoreline change using components of the process-based, three-dimensional coupled-ocean-atmosphere-wave-sediment transport modeling system (COAWST). COAWST is forced with historical predictions of atmospheric and oceanographic data from public-domain global models. Through a method of coupled concurrent grid-refinement approach in COAWST, the finest grid with resolution of O(10 m) that covers the surf zone along the section of interest is forced at its spatial boundaries with waves and currents computed on the grids that cover the U.S. East Coast with resolutions as low as O(1 km). The computed patterns of the gradients of surf-zone integrated longshore sediment transport rates are compared with the observed shoreline change.

Application of the Refined Zigzag Theory to the Modeling of Delaminations in Laminated Composites

NASA Technical Reports Server (NTRS)

Groh, Rainer M. J.; Weaver, Paul M.; Tessler, Alexander

2015-01-01

The Refined Zigzag Theory is applied to the modeling of delaminations in laminated composites. The commonly used cohesive zone approach is adapted for use within a continuum mechanics model, and then used to predict the onset and propagation of delamination in five cross-ply composite beams. The resin-rich area between individual composite plies is modeled explicitly using thin, discrete layers with isotropic material properties. A damage model is applied to these resin-rich layers to enable tracking of delamination propagation. The displacement jump across the damaged interfacial resin layer is captured using the zigzag function of the Refined Zigzag Theory. The overall model predicts the initiation of delamination to within 8% compared to experimental results and the load drop after propagation is represented accurately.

Microstructure and wear characterization of aluminum matrix composites reinforced with industrial waste fly ash particulates synthesized by friction stir processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dinaharan, I., E-mail: dinaweld2009@gmail.com

Fly ash (FA) is a waste product of coal combustion in thermal power plants which is available in massive quantities all over the world causing land pollution. This paper reports the characterization of AA6061 aluminum matrix composites (AMCs) reinforced with FA particles synthesized using friction stir processing (FSP). The volume fraction of FA particles was varied from 0 to 18 in steps of 6. The prepared AMCs were characterized using optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diagram (EBSD). The wear rate was estimated using a pin-on-disc wear apparatus. FA particles were observed to be distributed homogeneouslymore » in the AMC irrespective of the location within the stir zone. The EBSD micrographs revealed remarkable grain refinement in the AMC. The incorporation of FA particles enhanced the microhardness and wear resistance of the AMC. The strengthening mechanisms of the AMC were discussed and correlated to the observed microstructures. The wear mechanisms were identified by characterizing the wear debris and worn surfaces. - Highlights: •Industrial waste fly ash was used to produce aluminum matrix composites. •Friction stir processing was used to produce AA6061/Fly Ash composite. •Fly ash particles refined the grains of aluminum matrix. •Fly ash particles enhanced the hardness and wear resistance. •Successful utilization of fly ash to make aluminum composites reduces land pollution.« less

Formation mechanism and control of MgO·Al2O3 inclusions in non-oriented silicon steel

NASA Astrophysics Data System (ADS)

Sun, Yan-hui; Zeng, Ya-nan; Xu, Rui; Cai, Kai-ke

2014-11-01

On the basis of the practical production of non-oriented silicon steel, the formation of MgO·Al2O3 inclusions was analyzed in the process of "basic oxygen furnace (BOF) → RH → compact strip production (CSP)". The thermodynamic and kinetic conditions of the formation of MgO·Al2O3 inclusions were discussed, and the behavior of slag entrapment in molten steel during RH refining was simulated by computational fluid dynamics (CFD) software. The results showed that the MgO/Al2O3 mass ratio was in the range from 0.005 to 0.017 and that MgO·Al2O3 inclusions were not observed before the RH refining process. In contrast, the MgO/Al2O3 mass ratio was in the range from 0.30 to 0.50, and the percentage of MgO·Al2O3 spinel inclusions reached 58.4% of the total inclusions after the RH refining process. The compositions of the slag were similar to those of the inclusions; furthermore, the critical velocity of slag entrapment was calculated to be 0.45 m·s-1 at an argon flow rate of 698 L·min-1, as simulated using CFD software. When the test steel was in equilibrium with the slag, [Mg] was 0.00024wt%-0.00028wt% and [Al]s was 0.31wt%-0.37wt%; these concentrations were theoretically calculated to fall within the MgO·Al2O3 formation zone, thereby leading to the formation of MgO·Al2O3 inclusions in the steel. Thus, the formation of MgO·Al2O3 inclusions would be inhibited by reducing the quantity of slag entrapment, controlling the roughing slag during casting, and controlling the composition of the slag and the MgO content in the ladle refractory.

Magnesium Recycling of Partially Oxidized, Mixed Magnesium-Aluminum Scrap Through Combined Refining and Solid Oxide Membrane (SOM) Electrolysis Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guan, Xiaofei; Zink, Peter; Pal, Uday

2012-03-11

Pure magnesium (Mg) is recycled from 19g of partially oxidized 50.5wt.%Mg-Aluminum (Al) alloy. During the refining process, potentiodynamic scans (PDS) were performed to determine the electrorefining potential for magnesium. The PDS show that the electrorefining potential increases over time as the Mg content inside the Mg-Al scrap decreases. Up to 100% percent of magnesium is refined from the Mg-Al scrap by a novel refining process of dissolving magnesium and its oxide into a flux followed by vapor phase removal of dissolved magnesium and subsequently condensing the magnesium vapors in a separate condenser. The solid oxide membrane (SOM) electrolysis process ismore » employed in the refining system to enable additional recycling of magnesium from magnesium oxide (MgO) in the partially oxidized Mg-Al scrap. The combination of the refining and SOM processes yields 7.4g of pure magnesium; could not collect and weigh all of the magnesium recovered.« less

Separation of Lead from Crude Antimony by Pyro-Refining Process with NaPO3 Addition

NASA Astrophysics Data System (ADS)

Ye, Longgang; Hu, Yuejie; Xia, Zhimei; Chen, Yongming

2016-06-01

The main purpose of this study was to separate lead from crude antimony through an oxidation pyro-refining process and by using sodium metaphosphate as a lead elimination reagent. The process parameters that will affect the refining results were optimized experimentally under controlled conditions, such as the sodium metaphosphate charging dosage, the refining temperature and duration, and the air flow rate, to determine their effect on the lead content in refined antimony and the lead removal rate. A minimum lead content of 0.0522 wt.% and a 98.6% lead removal rate were obtained under the following optimal conditions: W_{{{NaPO}_{{3}} }} = 15% W Sb (where W represents weight), a refining temperature of 800°C, a refining time of 30 min, and an air flow rate of 3 L/min. X-ray diffractometry and scanning electron microscopy showed that high-purity antimony was obtained. The smelting operation is free from smoke or ammonia pollution when using monobasic sodium phosphate or ammonium dihydrogen phosphate as the lead elimination reagent. However, this refining process can also remove a certain amount of sulfur, cobalt, and silicon simultaneously, and smelting results also suggest that sodium metaphosphate can be used as a potential lead elimination reagent for bismuth and copper refining.

Computer-based self-organized tectonic zoning: a tentative pattern recognition for Iran

NASA Astrophysics Data System (ADS)

Zamani, Ahmad; Hashemi, Naser

2004-08-01

Conventional methods of tectonic zoning are frequently characterized by two deficiencies. The first one is the large uncertainty involved in tectonic zoning based on non-quantitative and subjective analysis. Failure to interpret accurately a large amount of data "by eye" is the second. In order to alleviate each of these deficiencies, the multivariate statistical method of cluster analysis has been utilized to seek and separate zones with similar tectonic pattern and construct automated self-organized multivariate tectonic zoning maps. This analytical method of tectonic regionalization is particularly useful for showing trends in tectonic evolution of a region that could not be discovered by any other means. To illustrate, this method has been applied for producing a general-purpose numerical tectonic zoning map of Iran. While there are some similarities between the self-organized multivariate numerical maps and the conventional maps, the cluster solution maps reveal some remarkable features that cannot be observed on the current tectonic maps. The following specific examples need to be noted: (1) The much disputed extent and rigidity of the Lut Rigid Block, described as the microplate of east Iran, is clearly revealed on the self-organized numerical maps. (2) The cluster solution maps reveal a striking similarity between this microplate and the northern Central Iran—including the Great Kavir region. (3) Contrary to the conventional map, the cluster solution maps make a clear distinction between the East Iranian Ranges and the Makran Mountains. (4) Moreover, an interesting similarity between the Azarbaijan region in the northwest and the Makran Mountains in the southeast and between the Kopet Dagh Ranges in the northeast and the Zagros Folded Belt in the southwest of Iran are revealed in the clustering process. This new approach to tectonic zoning is a starting point and is expected to be improved and refined by collection of new data. The method is also a useful tool in studying neotectonics, seismotectonics, seismic zoning, and hazard estimation of the seismogenic regions.

A genetically distinct hybrid zone occurs for two globally invasive mosquito fish species with striking phenotypic resemblance.

PubMed

Wilk, Rebecca J; Horth, Lisa

2016-12-01

Hybrid zones allow for the investigation of incipient speciation and related evolutionary processes of selection, gene flow, and migration. Interspecific dynamics, like competition, can impact the size, shape, and directional movement of species in hybrid zones. Hybrid zones contribute to a paradox for the biological species concept because interbreeding between species occurs while parental forms remain distinct. A long-standing zone of intergradation or introgression exists for eastern and western mosquito fish ( Gambusia holbrooki and G. affinis ) around Mobile Bay, AL. The region has been studied episodically, over decades, making it perfect for addressing temporal dynamics and for providing a deeper understanding of the genetics of these periodically reclassified fishes (as species or subspecies). We used six microsatellite markers to assess the current population structure and gene flow patterns across 19 populations of mosquito fish and then compared our results with historical data. Genetic evidence demonstrates that the current hybrid zone is located in a similar geographic region as the historical one, even after three decades. Hybrid fish, however, demonstrate relatively low heterozygosity and are genetically distinct from western and eastern mosquito fish populations. Fin ray counts, sometimes used to distinguish the two species from one another, demonstrate more eastern ( G. holbrooki) phenotype fish within the molecular genetic hybrid zone today. Mosquito fish are globally invasive, often found on the leading edge of flooded waters that they colonize, so the impact of hurricanes in the wake of climate change was also evaluated. An increase in the frequency and intensity of hurricanes in the hybrid region has occurred, and this point warrants further attention since hurricanes are known to move these aggressive, invasive species into novel territory. This work contributes to our classical understanding of hybrid zone temporal dynamics, refines our understanding of mosquito fish genetics in their native range, evaluates important genotype-phenotype relationships, and identifies a potential new impact of climate change.

Probabalistic Risk Assessment of a Turbine Disk

NASA Astrophysics Data System (ADS)

Carter, Jace A.; Thomas, Michael; Goswami, Tarun; Fecke, Ted

Current Federal Aviation Administration (FAA) rotor design certification practices risk assessment using a probabilistic framework focused on only the life-limiting defect location of a component. This method generates conservative approximations of the operational risk. The first section of this article covers a discretization method, which allows for a transition from this relative risk to an absolute risk where the component is discretized into regions called zones. General guidelines were established for the zone-refinement process based on the stress gradient topology in order to reach risk convergence. The second section covers a risk assessment method for predicting the total fatigue life due to fatigue induced damage. The total fatigue life incorporates a dual mechanism approach including the crack initiation life and propagation life while simultaneously determining the associated initial flaw sizes. A microstructure-based model was employed to address uncertainties in material response and relate crack initiation life with crack size, while propagation life was characterized large crack growth laws. The two proposed methods were applied to a representative Inconel 718 turbine disk. The zone-based method reduces the conservative approaches, while showing effects of feature-based inspection on the risk assessment. In the fatigue damage assessment, the predicted initial crack distribution was found to be the most sensitive probabilistic parameter and can be used to establish an enhanced inspection planning.

Practical Advances in Petroleum Processing

NASA Astrophysics Data System (ADS)

Hsu, Chang S.; Robinson, Paul R.

"This comprehensive book by Robinson and Hsu will certainly become the standard text book for the oil refining business...[A] must read for all who are associated with oil refining." - Dr. Walter Fritsch, Senior Vice President Refining, OMV "This book covers a very advanced horizon of petroleum processing technology. For all refiners facing regional and global environmental concerns, and for those who seek a more sophisticated understanding of the refining of petroleum resources, this book has been long in coming." - Mr. Naomasa Kondo, Cosmo Oil Company, Ltd.

Preliminary earthquake locations in the Kenai Peninsula recorded by the MOOS Array and their relationship to structure in the 1964 great earthquake zone

NASA Astrophysics Data System (ADS)

Li, J.; Abers, G. A.; Christensen, D. H.; Kim, Y.; Calkins, J. A.

2011-12-01

Earthquakes in subduction zones are mostly generated at the interface between the subducting and overlying plates. In 2006-2009, the MOOS (Multidisciplinary Observations Of Subduction) seismic array was deployed around the Kenai Peninsula, Alaska, consisting of 34 broadband seismometers recording for 1-3 years. This region spans the eastern end of the Aleutian megathrust that ruptured in the 1964 Mw 9.2 great earthquake, the second largest recorded earthquake, and ongoing seismicity is abundant. Here, we report an initial analysis of seismicity recorded by MOOS, in the context of preliminary imaging. There were 16,462 events detected in one year from initial STA/LTA signal detections and subsequent event associations from the MOOS Array. We manually reviewed them to eliminate distant earthquakes and noise, leaving 11,879 local earthquakes. To refine this catalog, an adaptive auto-regressive onset estimation algorithm was applied, doubling the original dataset and producing 20,659 P picks and 22,999 S picks for one month (September 2007). Inspection shows that this approach lead to almost negligible false alarms and many more events than hand picking. Within the well-sampled part of the array, roughly 200 km by 300 km, we locate 250% more earthquakes for one month than the permanent network catalog, or 10 earthquakes per day on this patch of the megathrust. Although the preliminary locations of earthquakes still show some scatter, we can see a concentration of events in a ~20-km-wide belt, part of which can be interpreted as seismogenic thrust zone. In conjunction with the seismicity study, we are imaging the plate interface with receiver functions. The main seismicity zone corresponds to the top of a low-velocity layer imaged in receiver functions, nominally attributed to the top of the downgoing plate. As we refine velocity models and apply relative relocation algorithms, we expect to improve the precision of the locations substantially. When combined with image of velocity structure from scattered wave migration, we can test whether the thrust zone is above the Yakutat terrane or between the Yakutat terrane and the subducting Pacific plate. Our refined relocations will also improve our understanding of other active faults (e.g., splay faults) and their relationship to the plate boundary.

An alternative regionalization scheme for defining nutrient criteria for rivers and streams

USGS Publications Warehouse

Robertson, Dale M.; Saad, David A.; Wieben, Ann M.

2001-01-01

The environmental nutrient zone approach can be applied to specific states or nutrient ecoregions and used to develop criteria as a function of stream type. This approach can also be applied on the basis of environmental characteristics of the watershed alone rather than the general environmental characteristics from the region in which the site is located. The environmental nutrient zone approach will enable states to refine the basic nutrient criteria established by the USEPA by developing attainable criteria given the environmental characteristics where the streams are located.

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2014 CFR

2014-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2012 CFR

2012-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2011 CFR

2011-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

49 CFR Appendix A to Part 222 - Approved Supplementary Safety Measures

Code of Federal Regulations, 2013 CFR

2013-10-01

... RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION USE OF LOCOMOTIVE HORNS AT PUBLIC HIGHWAY-RAIL GRADE... safety measures (SSMs) that may be installed at highway-rail grade crossings within quiet zones for risk... research and demonstration projects are completed and data is gathered and refined. Sections B and C govern...

Generation of sonic power during welding

NASA Technical Reports Server (NTRS)

Mc Campbell, W. M.

1969-01-01

Generation of intense sonic and ultrasonic power in the weld zone, close to the puddle, reduces the porosity and refinement of the grain. The ac induction brazing power supply is modified with long cables for deliberate addition of resistance to that circuit. The concept is extensible to the molding of metals and plastics.

Computer simulation of refining process of a high consistency disc refiner based on CFD

NASA Astrophysics Data System (ADS)

Wang, Ping; Yang, Jianwei; Wang, Jiahui

2017-08-01

In order to reduce refining energy consumption, the ANSYS CFX was used to simulate the refining process of a high consistency disc refiner. In the first it was assumed to be uniform Newton fluid of turbulent state in disc refiner with the k-ɛ flow model; then meshed grids and set the boundary conditions in 3-D model of the disc refiner; and then was simulated and analyzed; finally, the viscosity of the pulp were measured. The results show that the CFD method can be used to analyze the pressure and torque on the disc plate, so as to calculate the refining power, and streamlines and velocity vectors can also be observed. CFD simulation can optimize parameters of the bar and groove, which is of great significance to reduce the experimental cost and cycle.

Mechanisms of microstructure formation under the influence of ultrasonic vibrations

NASA Astrophysics Data System (ADS)

Rakita, Milan

Positive effects of ultrasound on crystallization have been known for almost 90 years. Application of ultrasound has been very successful in many industries, most notably in chemistry, creating a new branch of science - sonochemistry. However, ultrasonication has not found wide commercial application in the solidification processing. The reason for that is the complexity of underlying phenomena and the lack of predicting models which correlate processing parameters with the properties of a product. The purpose of this study is to give some contribution toward better understanding of mechanisms that lead to changes in the solidifying microstructure. It has been found that, under experimental conditions used in this work, cavitation-induced nucleation is the major contributor to the grain refinement. Ultrasonication at minimal supercoolings is expected to give maximal grain refinement. Dendrite fragmentation has not shown to be a significant contributor to the grain refinement. Dendrite fragmentation is maximal if done by bubbles that come in contact with the solidifying phase, or that are created there. Alloys/solutions with long solidification interval, or wide mushy zone, are expected to exhibit more dendrite fragmentation. Bubbles are recognized as a crucial feature in ultrasonication. Their size distribution in the liquid phase prior to ultrasonication dictates the cavitation threshold and intensity of cavitation. For the first time, radiation pressure has been recognized as potentially significant factor in grain refinement. In the experimental setup used in this study, acoustic pressure at the main (driving) frequency is not substantial to cause significant fragmentation, and only dendrites close to the sonotrode were fragmented. However, application of ultrasound with frequencies that are several times higher than the current industrial practice could substantially increase dendrite fragmentation. Appearance of fractional harmonics has also been recognized for the first time as potentially influential factor. The amplitude of pressure caused by these vibrations is quite sensible, and since resonant in nature, these pressure variations propagate throughout entire liquid volume. Although ultrasonication is a very efficient method for degassing melts, there is a risk of gas entrapment if ultrasound is applied during solidification. Heating can create unwanted effects during ultrasonication at small supercoolings.

Statistical characterization of planar two-dimensional Rayleigh-Taylor mixing layers

NASA Astrophysics Data System (ADS)

Sendersky, Dmitry

2000-10-01

The statistical evolution of a planar, randomly perturbed fluid interface subject to Rayleigh-Taylor instability is explored through numerical simulation in two space dimensions. The data set, generated by the front-tracking code FronTier, is highly resolved and covers a large ensemble of initial perturbations, allowing a more refined analysis of closure issues pertinent to the stochastic modeling of chaotic fluid mixing. We closely approach a two-fold convergence of the mean two-phase flow: convergence of the numerical solution under computational mesh refinement, and statistical convergence under increasing ensemble size. Quantities that appear in the two-phase averaged Euler equations are computed directly and analyzed for numerical and statistical convergence. Bulk averages show a high degree of convergence, while interfacial averages are convergent only in the outer portions of the mixing zone, where there is a coherent array of bubble and spike tips. Comparison with the familiar bubble/spike penetration law h = alphaAgt 2 is complicated by the lack of scale invariance, inability to carry the simulations to late time, the increasing Mach numbers of the bubble/spike tips, and sensitivity to the method of data analysis. Finally, we use the simulation data to analyze some constitutive properties of the mixing process.

Brillouin zone grid refinement for highly resolved ab initio THz optical properties of graphene

NASA Astrophysics Data System (ADS)

Warmbier, Robert; Quandt, Alexander

2018-07-01

Optical spectra of materials can in principle be calculated within numerical frameworks based on Density Functional Theory. The huge numerical effort involved in these methods severely constraints the accuracy achievable in practice. In the case of the THz spectrum of graphene the primary limitation lays in the density of the reciprocal space sampling. In this letter we have developed a non-uniform sampling using grid refinement to achieve a high local sampling density with only moderate numerical effort. The resulting THz electron energy loss spectrum shows a plasmon signal below 50 meV with a ω(q) ∝√{ q } dispersion relation.

Non-intrusive telemetry applications in the oilsands: from visible light and x-ray video to acoustic imaging and spectroscopy

NASA Astrophysics Data System (ADS)

Shaw, John M.

2013-06-01

While the production, transport and refining of oils from the oilsands of Alberta, and comparable resources elsewhere is performed at industrial scales, numerous technical and technological challenges and opportunities persist due to the ill defined nature of the resource. For example, bitumen and heavy oil comprise multiple bulk phases, self-organizing constituents at the microscale (liquid crystals) and the nano scale. There are no quantitative measures available at the molecular level. Non-intrusive telemetry is providing promising paths toward solutions, be they enabling technologies targeting process design, development or optimization, or more prosaic process control or process monitoring applications. Operation examples include automated large object and poor quality ore during mining, and monitoring the thickness and location of oil water interfacial zones within separation vessels. These applications involve real-time video image processing. X-ray transmission video imaging is used to enumerate organic phases present within a vessel, and to detect individual phase volumes, densities and elemental compositions. This is an enabling technology that provides phase equilibrium and phase composition data for production and refining process development, and fluid property myth debunking. A high-resolution two-dimensional acoustic mapping technique now at the proof of concept stage is expected to provide simultaneous fluid flow and fluid composition data within porous inorganic media. Again this is an enabling technology targeting visualization of diverse oil production process fundamentals at the pore scale. Far infrared spectroscopy coupled with detailed quantum mechanical calculations, may provide characteristic molecular motifs and intermolecular association data required for fluid characterization and process modeling. X-ray scattering (SAXS/WAXS/USAXS) provides characteristic supramolecular structure information that impacts fluid rheology and process fouling. The intent of this contribution is to present some of the challenges and to provide an introduction grounded in current work on non-intrusive telemetry applications - from a mine or reservoir to a refinery!

Separating intrinsic and scattering attenuation in full waveform sonic logging with radiative transfer theory

NASA Astrophysics Data System (ADS)

Durán, Evert L.; van Wijk, Kasper; Adam, Ludmila; Wallis, Irene C.

2018-05-01

Fitting the intensity of ensembles of sonic log waveforms with a radiative transfer model allows us to separate scattering from intrinsic attenuation in two wells of the Ngatamariki geothermal field, New Zealand. Independent estimates of scattering and intrinsic attenuation add to the geologic interpretation based on other well log data. Particularly, our estimates of the intrinsic attenuation confirm or refine inferences on fluid mobility in the subsurface. Zones of strong intrinsic attenuation in Well 1 correlate with identified feed zones in three of the six cases, and hint at permeability just above two of the other three zones. In Well 2, intrinsic attenuation estimates help identify all three identified permeable intervals, including a washout.

Semi-automatic mapping of fault rocks on a Digital Outcrop Model, Gole Larghe Fault Zone (Southern Alps, Italy)

NASA Astrophysics Data System (ADS)

Vho, Alice; Bistacchi, Andrea

2015-04-01

A quantitative analysis of fault-rock distribution is of paramount importance for studies of fault zone architecture, fault and earthquake mechanics, and fluid circulation along faults at depth. Here we present a semi-automatic workflow for fault-rock mapping on a Digital Outcrop Model (DOM). This workflow has been developed on a real case of study: the strike-slip Gole Larghe Fault Zone (GLFZ). It consists of a fault zone exhumed from ca. 10 km depth, hosted in granitoid rocks of Adamello batholith (Italian Southern Alps). Individual seismogenic slip surfaces generally show green cataclasites (cemented by the precipitation of epidote and K-feldspar from hydrothermal fluids) and more or less well preserved pseudotachylytes (black when well preserved, greenish to white when altered). First of all, a digital model for the outcrop is reconstructed with photogrammetric techniques, using a large number of high resolution digital photographs, processed with VisualSFM software. By using high resolution photographs the DOM can have a much higher resolution than with LIDAR surveys, up to 0.2 mm/pixel. Then, image processing is performed to map the fault-rock distribution with the ImageJ-Fiji package. Green cataclasites and epidote/K-feldspar veins can be quite easily separated from the host rock (tonalite) using spectral analysis. Particularly, band ratio and principal component analysis have been tested successfully. The mapping of black pseudotachylyte veins is more tricky because the differences between the pseudotachylyte and biotite spectral signature are not appreciable. For this reason we have tested different morphological processing tools aimed at identifying (and subtracting) the tiny biotite grains. We propose a solution based on binary images involving a combination of size and circularity thresholds. Comparing the results with manually segmented images, we noticed that major problems occur only when pseudotachylyte veins are very thin and discontinuous. After having tested and refined the image analysis processing for some typical images, we have recorded a macro with ImageJ-Fiji allowing to process all the images for a given DOM. As a result, the three different types of rocks can be semi-automatically mapped on large DOMs using a simple and efficient procedure. This allows to develop quantitative analyses of fault rock distribution and thickness, fault trace roughness/curvature and length, fault zone architecture, and alteration halos due to hydrothermal fluid-rock interaction. To improve our workflow, additional or different morphological operators could be integrated in our procedure to yield a better resolution on small and thin pseudotachylyte veins (e.g. perimeter/area ratio).

A new insight into ductile fracture of ultrafine-grained Al-Mg alloys.

PubMed

Yu, Hailiang; Tieu, A Kiet; Lu, Cheng; Liu, Xiong; Liu, Mao; Godbole, Ajit; Kong, Charlie; Qin, Qinghua

2015-04-08

It is well known that when coarse-grained metals undergo severe plastic deformation to be transformed into nano-grained metals, their ductility is reduced. However, there are no ductile fracture criteria developed based on grain refinement. In this paper, we propose a new relationship between ductile fracture and grain refinement during deformation, considering factors besides void nucleation and growth. Ultrafine-grained Al-Mg alloy sheets were fabricated using different rolling techniques at room and cryogenic temperatures. It is proposed for the first time that features of the microstructure near the fracture surface can be used to explain the ductile fracture post necking directly. We found that as grains are refined to a nano size which approaches the theoretical minimum achievable value, the material becomes brittle at the shear band zone. This may explain the tendency for ductile fracture in metals under plastic deformation.

A new insight into ductile fracture of ultrafine-grained Al-Mg alloys

PubMed Central

Yu, Hailiang; Tieu, A. Kiet; Lu, Cheng; Liu, Xiong; Liu, Mao; Godbole, Ajit; Kong, Charlie; Qin, Qinghua

2015-01-01

It is well known that when coarse-grained metals undergo severe plastic deformation to be transformed into nano-grained metals, their ductility is reduced. However, there are no ductile fracture criteria developed based on grain refinement. In this paper, we propose a new relationship between ductile fracture and grain refinement during deformation, considering factors besides void nucleation and growth. Ultrafine-grained Al-Mg alloy sheets were fabricated using different rolling techniques at room and cryogenic temperatures. It is proposed for the first time that features of the microstructure near the fracture surface can be used to explain the ductile fracture post necking directly. We found that as grains are refined to a nano size which approaches the theoretical minimum achievable value, the material becomes brittle at the shear band zone. This may explain the tendency for ductile fracture in metals under plastic deformation. PMID:25851228

A new insight into ductile fracture of ultrafine-grained Al-Mg alloys

NASA Astrophysics Data System (ADS)

Yu, Hailiang; Tieu, A. Kiet; Lu, Cheng; Liu, Xiong; Liu, Mao; Godbole, Ajit; Kong, Charlie; Qin, Qinghua

2015-04-01

It is well known that when coarse-grained metals undergo severe plastic deformation to be transformed into nano-grained metals, their ductility is reduced. However, there are no ductile fracture criteria developed based on grain refinement. In this paper, we propose a new relationship between ductile fracture and grain refinement during deformation, considering factors besides void nucleation and growth. Ultrafine-grained Al-Mg alloy sheets were fabricated using different rolling techniques at room and cryogenic temperatures. It is proposed for the first time that features of the microstructure near the fracture surface can be used to explain the ductile fracture post necking directly. We found that as grains are refined to a nano size which approaches the theoretical minimum achievable value, the material becomes brittle at the shear band zone. This may explain the tendency for ductile fracture in metals under plastic deformation.

Synthesis, purification and bulk crystal growth of radiation detector materials using melt growth technique

NASA Astrophysics Data System (ADS)

Surabhi, Raja Rahul Reddy

In the past decade, there has been new and increased usage of radiation-detection technologies for applications in homeland security, non-proliferation, and national defense. Most of these applications require a portable device with high gamma-ray energy resolution and detection efficiency, compact size, room-temperature operation, and low cost. Consequently, there is a renewed understanding of the material limitations for these technologies and a great demand to develop next-generation radiation-detection materials that can operate at room temperature. Mercuric iodide (HgI2), Lead iodide (PbI2), and CdZnTe (CZT) are the current leading candidates for radiation detector applications. This is because of their high atomic number and large band gap that makes them particularly well suited for fabrication of high resolution and high efficiency compact devices. PbI2 is a promising material for room temperature nuclear radiation detectors, characterized by its wide band gap (EG=2.32eV) and high-density (rho=6.2g/cm3). It has been reported that PbI2 crystal detectors are able to detect gamma-ray in the range of 1KeV-1MeV, with good energy resolution. However, PbI 2 detectors have not been studied in detail because of non-availability of high quality single crystals. This study presents the synthesis, purification, growth and characterization of PbI2 single crystals grown. In this research, solid-state synthesis technique has been utilized for obtaining PbI2 as a starting material. For the first time, a unique low-temperature purification technique has been developed to obtain high-purity starting material. The crystals were grown using 2-zone Bridgman-Stockbarger (B.S) technique wherein growth rate and temperature gradient at the solid-liquid interface were optimized. Single crystals of PbI2 were successfully grown in quartz glass ampoule under different growth conditions. Material purity was determined by measuring the elemental concentration using the Inductively coupled plasma-optical emission spectroscopy (ICP-OES). ICP-OES is utilized for estimating impurities present in the low-temperature purified material, zone refined material and melt grown PbI2 crystals. The zone-refined material contains no traceable amounts of impurities, whereas the low-temperature purified material and melt grown PbI2 crystals show very low concentration of K (potassium) and Na (sodium) impurities. Crystal characterization has been performed for determining optical properties by UV-VIS spectroscopy. The energy band gap (EG) is an important parameter for materials used for room temperature gamma-ray detector applications. The absorption peak at 530nm is a characteristic of PbI2 and corresponds to the onset of the transitions from the valence band to the exciton level. From this absorption spectrum the calculated indirect band gap of PbI 2 was 2.33+/-0.025 eV at room temperature. For measuring the electrical properties (Dielectric and I-V characteristics) of the crystal, Ag (silver) contacts are applied to both sides of the sample. Dielectric analysis on melt grown PbI2 showed that space charge polarization was dominant at lower frequencies but stabilizes at higher frequencies over different operating temperatures. On the other hand, dielectric analysis for zone-refined material space charge polarization was constant over the operating range resulting in fewer lattice defects. Therefore the low temperature purified material followed by zone-refined purification provides detector grade material with fewer lattice defects. The measured electrical resistivity for melt grown PbI2 and zone-refined material are 3.185 x 10 10 O-cm and 0.754 x 109 O-cm at room temperature along (001) plane respectively.

Integrated decontamination process for metals

DOEpatents

Snyder, Thomas S.; Whitlow, Graham A.

1991-01-01

An integrated process for decontamination of metals, particularly metals that are used in the nuclear energy industry contaminated with radioactive material. The process combines the processes of electrorefining and melt refining to purify metals that can be decontaminated using either electrorefining or melt refining processes.

The economic payoff for a state-of-the-art high-efficiency flat-plate crystalline silicon solar cell technology

NASA Technical Reports Server (NTRS)

Bickler, Donald B.; Callaghan, W. T.

1987-01-01

In 1986 during the flat-plate solar array project, silicon solar cells 4.0 sq cm in area were fabricated at the Jet Propulsion Laboratory (JPL) with a conversion efficiency of 20.1 percent (AM1.5-global). Sixteen cells were processed with efficiencies measuring 19.5 percent (AM1.5 global) or better. These cells were produced using refined versions of conventional processing methods, aside from certain advanced techniques that bring about a significant reduction in a major mechanism (surface recombination) that limits cell efficiency. Wacker Siltronic p-type float-zone 0.18-ohm-cm wafers were used. Conversion efficiencies in this range have previously been reported by other researchers, but generally on much smaller (0.5 vs. 4.0 cm) devices which have undergone sophisticated and costly processing steps. An economic analysis is presented of the potential payoffs for this approach, using the Solar Array Manufacturing Industry Costing Standards (SAMICS) methodology. The process sequence used and the assumptions made for capturing the economies of scale are presented.

History of late Holocene earthquakes at the Willow Creek site on the Nephi segment, Wasatch fault zone, Utah

USGS Publications Warehouse

Crone, Anthony J.; Personius, Stephen F.; Duross, Christopher; Machette, Michael N.; Mahan, Shannon

2014-01-01

This 43-page report presents new data from the Willow Creek site that provides well-defined and narrow bounds on the times of the three youngest earthquakes on the southern strand of the Nephi segment, Wasatch Fault zone, and refines the time of the youngest earthquake to about 200 years ago. This is the youngest surface rupture on the entire Wasatch fault zone, which occurred about a century or less before European settles arrived in Utah. Two trenches at the Willow Creek site exposed three scarp-derived colluvial wedges that are evidence of three paleoearthquakes. OxCal modeling of ages from Willow Creek indicate that paleoearthquake WC1 occurred at 0.2 ± 0.1 ka, WC2 occurred at 1.2 ± 0.1 ka, and WC3 occurred at 1.9 ± 0.6 ka. Stratigraphic constraints on the time of paleoearthquake WC4 are extremely poor, so OxCal modeling only yields a broadly constrained age of 4.7 ± 1.8 ka. Results from the Willow Creek site significantly refine the times of late Holocene earthquakes on the Southern strand of the Nephi segment, and this result, when combined with a reanalysis of the stratigraphic and chronologic information from previous investigations at North Creek and Red Canyon, yield a stronger basis of correlating individual earthquakes between all three sites.

Modeling of the Coupling of Microstructure and Macrosegregation in a Direct Chill Cast Al-Cu Billet

NASA Astrophysics Data System (ADS)

Heyvaert, Laurent; Bedel, Marie; Založnik, Miha; Combeau, Hervé

2017-10-01

The macroscopic multiphase flow and the growth of the solidification microstructures in the mushy zone of a direct chill (DC) casting are closely coupled. These couplings are the key to the understanding of the formation of the macrosegregation and of the non-uniform microstructure of the casting. In the present paper we use a multiphase and multiscale model to provide a fully coupled picture of the links between macrosegregation and microstructure in a DC cast billet. The model describes nucleation from inoculant particles and growth of dendritic and globular equiaxed crystal grains, fully coupled with macroscopic transport phenomena: fluid flow induced by natural convection and solidification shrinkage, heat, mass, and solute mass transport, motion of free-floating equiaxed grains, and of grain refiner particles. We compare our simulations to experiments on grain-refined and non-grain-refined industrial size billets from literature. We show that a transition between dendritic and globular grain morphology triggered by the grain refinement is the key to the explanation of the differences between the macrosegregation patterns in the two billets. We further show that the grain size and morphology are strongly affected by the macroscopic transport of free-floating equiaxed grains and of grain refiner particles.

Enhanced Representation of Turbulent Flow Phenomena in Large-Eddy Simulations of the Atmospheric Boundary Layer using Grid Refinement with Pseudo-Spectral Numerics

NASA Astrophysics Data System (ADS)

Torkelson, G. Q.; Stoll, R., II

2017-12-01

Large Eddy Simulation (LES) is a tool commonly used to study the turbulent transport of momentum, heat, and moisture in the Atmospheric Boundary Layer (ABL). For a wide range of ABL LES applications, representing the full range of turbulent length scales in the flow field is a challenge. This is an acute problem in regions of the ABL with strong velocity or scalar gradients, which are typically poorly resolved by standard computational grids (e.g., near the ground surface, in the entrainment zone). Most efforts to address this problem have focused on advanced sub-grid scale (SGS) turbulence model development, or on the use of massive computational resources. While some work exists using embedded meshes, very little has been done on the use of grid refinement. Here, we explore the benefits of grid refinement in a pseudo-spectral LES numerical code. The code utilizes both uniform refinement of the grid in horizontal directions, and stretching of the grid in the vertical direction. Combining the two techniques allows us to refine areas of the flow while maintaining an acceptable grid aspect ratio. In tests that used only refinement of the vertical grid spacing, large grid aspect ratios were found to cause a significant unphysical spike in the stream-wise velocity variance near the ground surface. This was especially problematic in simulations of stably-stratified ABL flows. The use of advanced SGS models was not sufficient to alleviate this issue. The new refinement technique is evaluated using a series of idealized simulation test cases of neutrally and stably stratified ABLs. These test cases illustrate the ability of grid refinement to increase computational efficiency without loss in the representation of statistical features of the flow field.

Glycidyl fatty acid esters in refined edible oils: A review on formation, occurrence, analysis, and elimination methods

USDA-ARS?s Scientific Manuscript database

Glycidyl fatty acid esters (GEs), one of the main contaminants in processed oil, are mainly formed during the deodorization step in the oil refining process of edible oils and therefore occur in almost all refined edible oils. GEs are potential carcinogens, due to the fact that they hydrolyze into t...

Turbulent transport modeling of shear flows around an aerodynamic wing. Development of turbulent near-wall model and its application to recirculating flows

NASA Technical Reports Server (NTRS)

Amano, R. S.

1982-01-01

Progress in implementing and refining two near-wall turbulence models in which the near-wall region is divided into either two or three zones is outlined. These models were successfully applied to the computation of recirculating flows. The research was further extended to obtaining experimental results of two different recirculating flow conditions in order to check the validity of the present models. Two different experimental apparatuses were set up: axisymmetric turbulent impinging jets on a flat plate, and turbulent flows in a circular pipe with a abrupt pipe expansion. It is shown that generally better results are obtained by using the present near-wall models, and among the models the three-zone model is superior to the two-zone model.

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR 409.30 - Applicability; description of the liquid cane sugar refining subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... liquid cane sugar refining subcategory. 409.30 Section 409.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.30 Applicability; description of the liquid cane sugar refining...

40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 15 2012-07-01 2012-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet the...

40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 15 2013-07-01 2013-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet the...

40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 14 2011-07-01 2011-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet the...

40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 15 2014-07-01 2014-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet the...

40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet the...

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.21... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

Seasonal Hydrologic Controls on Uranium and Iron Biogeochemistry in a Riparian Aquifer

NASA Astrophysics Data System (ADS)

Wilkins, M.; Williams, K. H.; Danczak, R. E.; Yabusaki, S.; Fang, Y.; Hobson, C.

2015-12-01

The maintenance of geochemically reducing conditions is generally optimal for the formation and preservation of reduced metals and mineral phases that can limit contaminant fate and transport. At a riparian aquifer near Rifle, CO, we tracked over six months the biogeochemical response within the aquifer to an annual pulse of dissolved oxygen (DO) that results from snowmelt-driven changes in Colorado River stage. In reduced portions of the aquifer (naturally reduced zones; NRZs) the re-oxidation of abundant iron sulfide minerals was the dominant oxygen-consuming process, and resulted in little DO intrusion into the deeper aquifer. In less reduced areas, DO intruded through the entire vertical profile of the aquifer. Across both regions, these perturbations resulted in changes to the microbial community structure, and aqueous metal pools. Two potentially different mechanisms of uranium mobilization were observed; (1) re-oxidation of reduced U(IV) phases in response to DO intrusion, and (2) mobilization of U(VI) from the vadose zone during water table rise. This high-resolution, long-term monitoring of aquifer biogeochemistry at the Rifle site has revealed dynamic microbial and geochemical responses to predictable, annual hydrologic perturbations, and offers an opportunity to further refine modeling approaches for such regions.

Study on the Control of Cleanliness for X90 Pipeline in the Secondary Refining Process

NASA Astrophysics Data System (ADS)

Chu, Ren Sheng; Liu, Jin Gang; Li, Zhan Jun

X90 pipeline steel requires ultra low for sulfur content and gas content in the smelting process. The secondary refining process is very important for X90 pipeline in smelting process and the control of cleanliness is the key for the secondary refining process in the steelmaking process for Pretreatment of hot metal → LD → LF refining → RH refining → Calcium treatment → CC. In the current paper, the cleanliness control method of secondary refining was analyzed for the evolution of non-metallic inclusions in the secondary refining prcess and related changes for composition in steel. The size, composition and the type of the non-metallic inclusions were analyzed by aspex explorer automated scanning electron microscope in X90 pipeline samples for 20mm * 25mm * 25mm by the line cutting. The results show that the number of non-metallic inclusions in steel decrease from the beginning of the LF refining to the RH refining. In the composition of the Non-metallic inclusions, the initial non-metallic inclusions of alumina is converted to two comple-type non-metallic inclusions. Most of them, the non-metallic inclusions were composed by the calcium aluminate and CaS. The others are that the spinel is the core, peripheral parcels calcium aluminate nonmetallic inclusions for complex-type non-metallic inclusions. For the size of the non-metallic inclusions, the non-metallic inclusions for size larger than 100µm is converted to 5 20µm based small size non-metallic inclusions. While the S content of the steel decreased from 0.012% to 0.0012% or less, Al content is kept at between 0.025% to 0.035% and the quality for the casting slab satisfies the requirement of the steel. The ratings for various types of the non-metallic inclusions are 1.5 or less. The control strategy for the inclusions in 90 pipeline is small size, diffuse distribution and little amount of the deformation after rolling. On the contrary, the specific chemical composition of the inclusions is not important, single component in the inclusions is better.

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31... (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

The evolution of microstructures, corrosion resistance and mechanical properties of AZ80 joints using ultrasonic vibration assisted welding process

NASA Astrophysics Data System (ADS)

Li, Hui; Zhang, Jiansheng

2017-12-01

The evolution of microstructures, corrosion resistance and mechanical properties of AZ80 joints using an ultrasonic vibration assisted welding process is investigated. The results show that, with ultrasonic vibration treatment, a reliable AZ80 joint without defects is obtained. The coarsening α-Mg grains are refined to about 83.5  ±  3.3 µm and the continuous β-Mg17Al12 phases are broken to granular morphology, owing to the acoustic streaming effect and the cavitation effect evoked by ultrasonic vibration. Both immersion and electrochemical test results indicate that the corrosion resistance of the AZ80 joint welded with ultrasonic vibration is improved, attributed to microstructure evolution. With ultrasonic power of 900 W, the maximum tensile strength of an AZ80 specimen is 261  ±  7.5 MPa and fracture occurs near the heat affected zone of the joint.

Late Quaternary uplift rate inferred from marine terraces, Shimokita Peninsula, northeastern Japan: A preliminary investigation of the buried shoreline angle

NASA Astrophysics Data System (ADS)

Matsu'ura, Tabito; Kimura, Haruo; Komatsubara, Junko; Goto, Norihisa; Yanagida, Makoto; Ichikawa, Kiyoshi; Furusawa, Akira

2014-03-01

After estimating tectonic uplift rates along the northern part of the northeast Japan forearc (the overriding plate in the northeast Japan subduction zone) by mapping the elevation of the inner edges of marine terrace surfaces, we refined this estimate through elevation measurements of the buried shoreline angle beneath well-dated marine terrace surfaces, from which we could derive more accurate paleo-sea levels. The uplift rate initially inferred from the inner edge of marine terrace T4, correlated with marine isotope stage MIS 5e by tephrochronology, increases eastward from 0.11-0.22 m ky- 1 around the backarc volcanic front to 0.17-0.32 m ky- 1 in the forearc on the peninsula of Shiriyazaki. We refined the uplift rates for T4, on the basis of the shoreline angle elevation, from the reconstructed profile of the paleo-sea cliff and wave-cut platform on a rocky coast and the reconstructed profile of the swash zone sediments and terrace deposits on a sandy coast. The refined uplift rates were 0.14-0.25 m ky- 1 on the rocky coast and 0.14-0.23 m ky- 1 on the sandy coast, slightly slower than the rates we inferred from the height of T4 and about one-half to three-fourths of previously reported rates. By extrapolation from the example of the sandy coast, the refined uplift rate around the volcanic front was 0.09-0.18 m ky- 1. The vertical deformation across the forearc of the Shimokita Peninsula since MIS 5e is possibly associated with regional isostatic uplift of 0.09-0.18 m ky- 1 and anticlinal deformation by an offshore fault, interpreted from acoustic profiles, of 0.05-0.07 m ky- 1.

40 CFR 409.21 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409... raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

Formation and mechanism of nanocrystalline AZ91 powders during HDDR processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Yafen; Fan, Jianfeng, E-mail: fanjianfeng@tyu

2017-03-15

Grain sizes of AZ91 alloy powders were markedly refined to about 15 nm from 100 to 160 μm by an optimized hydrogenation-disproportionation-desorption-recombination (HDDR) process. The effect of temperature, hydrogen pressure and processing time on phase and microstructure evolution of AZ91 alloy powders during HDDR process was investigated systematically by X-ray diffraction, optical microscopy, scanning electron microscopy and transmission electron microscopy, respectively. The optimal HDDR process for preparing nanocrystalline Mg alloy powders is hydriding at temperature of 350 °C under 4 MPa hydrogen pressure for 12 h and dehydriding at 350 °C for 3 h in vacuum. A modified unreacted coremore » model was introduced to describe the mechanism of grain refinement of during HDDR process. - Highlights: • Grain size of the AZ91 alloy powders was significantly refined from 100 μm to 15 nm. • The optimal HDDR technology for nano Mg alloy powders is obtained. • A modified unreacted core model of grain refinement mechanism was proposed.« less

Cold flow simulation of an internal combustion engine with vertical valves using layering approach

NASA Astrophysics Data System (ADS)

Martinas, G.; Cupsa, O. S.; Stan, L. C.; Arsenie, A.

2015-11-01

Complying with emission requirements and fuel consumption efficiency are the points which drive any development of internal combustion engine. Refinement of the process of combustion and mixture formation, together with in-cylinder flow refinement, is a requirement, valves and piston bowl and intake exhaust port design optimization is essential. In order to reduce the time for design optimization cycle it is used Computational Fluid Dynamics (CFD). Being time consuming and highly costly caring out of experiment using flow bench testing this methods start to become less utilized. Air motion inside the intake manifold is one of the important factors, which govern the engine performance and emission of multi-cylinder diesel engines. Any cold flow study on IC is targeting the process of identifying and improving the fluid flow inside the ports and the combustion chamber. This is only the base for an optimization process targeting to increase the volume of air accessing the combustion space and to increase the turbulence of the air at the end of the compression stage. One of the first conclusions will be that the valve diameter is a fine tradeoff between the need for a bigger diameter involving a greater mass of air filling the cylinder, and the need of a smaller diameter in order to reduce the blind zone. Here there is room for optimization studies. The relative pressure indicates a suction effect coming from the moving piston. The more the shape of the inlet port is smoother and the diameter of the piston is bigger, the aerodynamic resistance of the geometry will be smaller so that the difference of inlet port pressure and the pressure near to piston face will be smaller. Here again there is enough room for more optimization studies.

Post-treatment mechanical refining as a method to improve overall sugar recovery of steam pretreated hybrid poplar.

PubMed

Dou, Chang; Ewanick, Shannon; Bura, Renata; Gustafson, Rick

2016-05-01

This study investigates the effect of mechanical refining to improve the sugar yield from biomass processed under a wide range of steam pretreatment conditions. Hybrid poplar chips were steam pretreated using six different conditions with or without SO2. The resulting water insoluble fractions were subjected to mechanical refining. After refining, poplar pretreated at 205°C for 10min without SO2 obtained a 32% improvement in enzymatic hydrolysis and achieved similar overall monomeric sugar recovery (539kg/tonne) to samples pretreated with SO2. Refining did not improve hydrolyzability of samples pretreated at more severe conditions, nor did it improve the overall sugar recovery. By maximizing overall sugar recovery, refining could partially decouple the pretreatment from other unit operations, and enable the use of low temperature, non-sulfur pretreatment conditions. The study demonstrates the possibility of using post-treatment refining to accommodate potential pretreatment process upsets without sacrificing sugar yields. Copyright © 2016 Elsevier Ltd. All rights reserved.

Integrated process for the solvent refining of coal

DOEpatents

Garg, Diwakar

1983-01-01

A process is set forth for the integrated liquefaction of coal by the catalytic solvent refining of a feed coal in a first stage to liquid and solid products and the catalytic hydrogenation of the solid product in a second stage to produce additional liquid product. A fresh inexpensive, throw-away catalyst is utilized in the second stage hydrogenation of the solid product and this catalyst is recovered and recycled for catalyst duty in the solvent refining stage without any activation steps performed on the used catalyst prior to its use in the solvent refining of feed coal.

Precipitation process in a Mg–Gd–Y alloy grain-refined by Al addition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Jichun; CAST Cooperative Research Centre, Department of Materials Engineering, Monash University, Victoria 3800; Zhu, Suming, E-mail: suming.zhu@monash.edu

2014-02-15

The precipitation process in Mg–10Gd–3Y (wt.%) alloy grain-refined by 0.8 wt.% Al addition has been investigated by transmission electron microscopy. The alloy was given a solution treatment at 520 °C for 6 h plus 550 °C for 7 h before ageing at 250 °C. Plate-shaped intermetallic particles with the 18R-type long-period stacking ordered structure were observed in the solution-treated state. Upon isothermal ageing at 250 °C, the following precipitation sequence was identified for the α-Mg supersaturated solution: β″ (D0{sub 19}) → β′ (bco) → β{sub 1} (fcc) → β (fcc). The observed precipitation process and age hardening response in themore » Al grain-refined Mg–10Gd–3Y alloy are compared with those reported in the Zr grain-refined counterpart. - Highlights: • The precipitation process in Mg–10Gd–3Y–0.8Al (wt.%) alloy has been investigated. • Particles with the 18R-type LPSO structure were observed in the solution state. • Upon ageing at 250 °C, the precipitation sequence is: β″ → β′ → β1 (fcc) → β. • The Al grain-refined alloy has a lower hardness than the Zr refined counterpart.« less

Observation of changes in the metallurgical characteristics of Ni-Cr alloys using Nd:YAG laser welding

PubMed Central

Choi, SM

2014-01-01

This study aimed to determine the effect of hardness change according to penetration depth in the laser fusing zone and observed the correlation of the microstructure as an Nd:YAG laser was irradiated to Ni-Cr alloy for dental use by setting the spot diameter size to various conditions. In all groups, the hardness depth profiles in the laser fusing zone and heat-affected zone (HAZ) had larger values than those of the base metal. In addition, the hardness values in places beyond the fusing zone and the HAZ were measured as being quantitatively lower. The observation result of the diffusion of the constituent elements and microstructure using field emission scanning electron microscopy, energy-dispersive spectroscopy, and electron probe microanalyzer showed that the fusing zone revealed a much finer dendritic form than the base metal due to the self-quenching effect after welding, while no change in constituent elements was found although some evaporation of the main elements was observed. In addition, Mo- and Si-combined intermetallic compounds were formed on the interdendritic area. Through this study, the laser fusing zone had better hardenability due to the intermetallic compound and grain refinement effect. PMID:25342985

78 FR 36150 - Fisheries of the Exclusive Economic Zone Off Alaska; Tanner Crab Area Closure in the Gulf of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-17

..., the Council initially reviewed alternative bycatch control measures, subsequently revised and refined... gear uses a pair of long lines called ``sweeps'' to herd fish into the net. The sweeps drag across the... from nonpelagic trawl fishing, which account only for crabs that come up in the trawl net. As noted in...

78 FR 33040 - Fisheries of the Exclusive Economic Zone Off Alaska; Fisheries of the Gulf of Alaska; Amendment...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-03

..., the Council initially reviewed alternative bycatch control measures, subsequently revised and refined... the gear. Nonpelagic trawl gear uses a pair of long lines called ``sweeps'' to herd fish into the net... fishing, which account only for crabs that come up in the trawl net. As noted in Section 2.9 of the Trawl...

Heat-affected zone microstructure and mechanical properties evolution for laser remanufacturing 35CrMoA axle steel

NASA Astrophysics Data System (ADS)

Feng, Xiangyi; Dong, Shiyun; Yan, Shixing; Liu, Xiaoting; Xu, Binshi; Pan, Fusheng

2018-03-01

In this article, by using orthogonal test the technological test was conducted and the optimum processing of the remanufacturing35CrMoA axle were obtained. The evolution of microstructure and mechanical property of HAZ were investigated. The microstructure of HAZ was characterized by means of OM and SEM. Meanwhile hardness distribution in HAZ and tensile property of cladding-HAZ-substrate samples were measured. The microstructure of cladding and HAZ were observed. The microsturcture evoltion and the mechanism of harden in the HAZ was discussed and revealed. The results indicated that the remanufacturing part has excellent strength due to grain refining and dispersive distribution of nanoscale cementite. The remanufacturing part will have uniform microstructure and hardness matching with that of 35CrMoA axle by using stress-relieving annealing at 580°.

Preparative isolation of huperzines A and B from Huperzia serrata by displacement centrifugal partition chromatography.

PubMed

Toribio, Alix; Delannay, Eldra; Richard, Bernard; Plé, Karen; Zèches-Hanrot, Monique; Nuzillard, Jean-Marc; Renault, Jean-Hugues

2007-01-26

The pH-zone refining centrifugal partition chromatography technique was used to separate the two acetylcholinesterase inhibitors huperzines A and B from a crude alkaloid extract of the club moss Huperzia serrata. Complete co-elution of huperzines A and B was initially observed with the well-known methyl tert-butyl ether-acetonitrile-water (4:1:5, v/v/v) solvent system with triethylamine (8mM) as the displacer and methane sulfonic acid (6mM) as the retainer. An efficient biphasic system was designed on the basis of solvent association that provided selectivity in the elution mode: n-heptane/ethyl acetate/n-propanol/water (5:15:35:45, v/v/v/v). Lowering the bridge solvent content (n-propanol) of this system increased the polarity difference between the two phases thus adapting it to the pH-zone refining mode. Thus, the purification of these compounds was achieved using the biphasic system n-heptane/ethyl acetate/n-propanol/water (10:30:15:45, v/v/v/v) with triethylamine (8mM) as the displacer and methane sulfonic acid (6mM) as the retainer.

Isolation of a furan fatty acid from Hevea brasiliensis latex employing the combined use of pH-zone-refining and conventional countercurrent chromatography.

PubMed

Englert, Michael; Ulms, Kerstin; Wendlinger, Christine; Vetter, Walter

2016-02-01

Furan fatty acids are valuable and bioactive minor fatty acids that usually contribute <0.1% to the fatty acid content of food samples. Their biological role still remains unclear as authentic furan fatty acid standards are not readily available and thorough experimental studies verifying the relevance of furan fatty acids are thus virtually impossible. An efficient protocol for the isolation of the furan fatty acid 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid from hydrolyzed and centrifuged latex of Hevea brasiliensis was developed using countercurrent chromatography. A first run using pH-zone-refining countercurrent chromatography provided 48.4 mg of 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid from 210 mg latex extract in a purity of 95%. The purity was increased to 99% by means of one second run in conventional countercurrent chromatography mode. The Structure and purity of 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid were determined by gas chromatography coupled to mass spectrometry and (1)H and (13)C NMR spectroscopy. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An unmetasomatized source for the Malaitan alnoeite (Solomon Islands): Petrogenesis involving zone refining, megacryst fractionation, and assimilation of oceanic lithosphere

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neal, C.R.; Davidson, J.P.

The Malaitan alnoite contains a rich and varied megacryst suite of unprecedented compositional range. The authors have undertaken trace element and isotope modeling in order to formulate a petrogenetic scheme which links the host alnoeite to its entrained megacrysts. This requires that a proto-alnoeite magma is the product of zone refining initiated by diapiric upwelling (where the initial melt passes through 200 times its volume of mantle). Isotopic evidence indicates the source of the proto-alnoeite contains a time-integrated LREE-depleted signature. Impingement upon the rigid lithosphere halts or dramatically slows the upward progress of the mantle diapir. At this point, themore » magma cools and megacryst fractionation begins with augites crystallizing first, followed by subcalcic diopsides and finally phlogopites. Garnet probably crystallizes over the entire range of clinopyroxene fractionation. Estimated proportions of fractionating phases are 30% augite, 24.5% subcalcic diopside, 27% garnet, 12.9% phlogopite, 5% bronzite, 0.5% ilmenite, and 0.1% zircon. As this proto-alnoeite magma crystallizes, it assimilates a subducted component of seawater-altered basalt which underplates the Ontong Java Plateau. This is witnessed in the isotopic composition of the megacrysts and alnoeite.« less

Effect of laser welding parameters on the austenite and martensite phase fractions of NiTi

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oliveira, J.P., E-mail: jp.oliveira@campus.fct.unl

Although laser welding is probably the most used joining technique for NiTi shape memory alloys there is still a lack of understanding about the effects of laser welding parameters on the microstructural induced changes: in both the heat affected and fusion zones martensite may be present, while the base material is fully austenitic. Synchrotron X-ray diffraction was used for fine probing laser welded NiTi joints. Through Rietveld refinement the martensite and austenite phase fractions were determined and it was observed that the martensite content increases towards the weld centreline. This is related to a change of the local transformation temperaturesmore » on these regions, which occurs due to compositional variation in those regions. The martensite phase fraction in the thermally affected regions may have significant implications on functional properties on these joints. - Highlights: •Synchrotron X-ray diffraction was used for fine probing of the microstructure in laser welded NiTi joints. •Rietveld refinement allowed to determine the content of martensite along the heat affected and fusion zones. •The martensite content increases from the base material towards the weld centreline.« less

Preparative isolation of alkaloids from Dactylicapnos scandens using pH-zone-refining counter-current chromatography by changing the length of the separation column.

PubMed

Wang, Xiao; Dong, Hongjing; Yang, Bin; Liu, Dahui; Duan, Wenjuan; Huang, Luqi

2011-12-01

pH-Zone-refining counter-current chromatography was successfully applied for the preparative separation of alkaloids from Dactylicapnos scandens. The two-phase solvent system was composed of petroleum ether-ethyl acetate-methanol-water (3:7:1:9, v/v), where 20 mM of triethylamine (TEA) was added to the upper phase as a retainer and 5 mM of hydrochloric acid (HCl) to the aqueous phase as an eluter. In this experiment, the apparatus with an adjustable length of the separation column was used for the separation of alkaloids from D. scandens and the resolution of the compounds can be remarkably improved by increasing the length of the separation column. As a result, 70 mg protopin, 30 mg (+) corydine, 120 mg (+) isocorydine and 40 mg (+) glaucine were obtained from 1.0 g of the crude extracts and each with 99.2%, 96.5%, 99.3%, 99.5% purity as determined by HPLC. The chemical structures of these compounds were confirmed by positive ESI-MS and (1)H NMR. Copyright © 2011 Elsevier B.V. All rights reserved.

40 CFR 80.1339 - Who is not eligible for the provisions for small refiners?

Code of Federal Regulations, 2010 CFR

2010-07-01

... eligible for the hardship provisions for small refiners: (a) A refiner with one or more refineries built... employees or crude capacity is due to operational changes at the refinery or a company sale or... refinery processing units. (e)(1) A small refiner approved under § 80.1340 that subsequently ceases...

Mechanical Properties and Microstructure of Dissimilar Friction Stir Welds of 11Cr-Ferritic/Martensitic Steel to 316 Stainless Steel

NASA Astrophysics Data System (ADS)

Sato, Yutaka S.; Kokawa, Hiroyuki; Fujii, Hiromichi T.; Yano, Yasuhide; Sekio, Yoshihiro

2015-12-01

Dissimilar joints between ferritic and austenitic steels are of interest for selected applications in next generation fast reactors. In this study, dissimilar friction-stir welding of an 11 pct Cr ferritic/martensitic steel to a 316 austenitic stainless steel was attempted and the mechanical properties and microstructure of the resulting welds were examined. Friction-stir welding produces a stir zone without macroscopic weld-defects, but the two dissimilar steels are not intermixed. The two dissimilar steels are interleaved along a sharp zigzagging interface in the stir zone. During small-sized tensile testing of the stir zone, this sharp interface did not act as a fracture site. Furthermore, the microstructure of the stir zone was refined in both the ferritic/martensitic steel and the 316 stainless steel resulting in improved mechanical properties over the adjacent base material regions. This study demonstrates that friction-stir welding can produce welds between dissimilar steels that contain no macroscopic weld-defects and display suitable mechanical properties.

Microstructure and Mechanical Properties of 21-6-9 Stainless Steel Electron Beam Welds

NASA Astrophysics Data System (ADS)

Elmer, John W.; Ellsworth, G. Fred; Florando, Jeffrey N.; Golosker, Ilya V.; Mulay, Rupalee P.

2017-04-01

Welds can either be stronger or weaker than the base metals that they join depending on the microstructures that form in the fusion and heat-affected zones of the weld. In this paper, weld strengthening in the fusion zone of annealed 21-6-9 stainless steel is investigated using cross-weld tensile samples, hardness testing, and microstructural characterization. Due to the stronger nature of the weld, the cross-weld tensile tests failed in the base metal and were not able to generate true fusion zone mechanical properties. Nanoindentation with a spherical indenter was instead used to predict the tensile behavior for the weld metal. Extrapolation of the nanoindentation results to higher strains was performed using the Steinberg-Guinan and Johnson-Cook strength models, and the results can be used for weld strength modeling purposes. The results illustrate how microstructural refinement and residual ferrite formation in the weld fusion zone can be an effective strengthener for 21-6-9 stainless steel.

Simulation model of Skeletonema costatum population dynamics in northern San Francisco Bay, California

USGS Publications Warehouse

Cloern, J.E.; Cheng, R.T.

1981-01-01

A pseudo-two-dimensional model is developed to simulate population dynamics of one dominant phytoplankton species (Skeletonema costatum) in northern San Francisco Bay. The model is formulated around a conceptualization of this estuary as two distinct but coupled subsystems-a deep (10-20 m) central channel and lateral areas with shallow (<2 m) water and slow circulation. Algal growth rates are governed by solar irradiation, temperature and salinity, while population losses are assumed to result from grazing bycalanoid copepods. Consequences of estuarine gravitational circulation are approximated simply by reducing convective-dispersive transport in that section of the channel (null zone) where residual bottom currents are near zero, and lateral mixing is treated as a bulkexchange process between the channel and the shoals. Model output is consistent with the hypothesis that, because planktonic algae are light-limited, shallow areas are the sites of active population growth. Seasonal variation in the location of the null zone (a response to variable river discharge) is responsible for maintaining the spring bloom of neritic diatoms in the seaward reaches of the estuary (San Pablo Bay) and the summer bloom upstream (Suisun Bay). Model output suggests that these spring and summer blooms result from the same general process-establishment of populations over the shoals, where growth rates are rapid, coupled with reduced particulate transport due to estuarine gravitational circulation. It also suggests, however, that the relative importance of physical and biological processes to phytoplankton dynamics is different in San Pablo and Suisun Bays. Finally, the model has helped us determine those processes having sufficient importance to merit further refinement in the next generation of models, and it has given new direction to field studies. ?? 1981 Academic Press Inc. (London) Ltd.

Exploration of interaction zones of β-tubulin colchicine binding domain of helminths and binding mechanism of anthelmintics.

PubMed

Ranjan, Prabodh; Kumar, Sivakumar Prasanth; Kari, Vijayakrishna; Jha, Prakash Chandra

2017-06-01

Numerous studies postulated the possible modes of anthelmintic activity by targeting alternate or extended regions of colchicine binding domain of helminth β-tubulin. We present three interaction zones (zones vide -1 to -3) in the colchicine binding domain of Haemonchus contortus (a helminth) β-tubulin homology model and developed zone-wise structure-based pharmacophore models coupled with molecular docking technique to unveil the binding hypotheses. The resulted ten structure-based hypotheses were then refined to essential three point pharmacophore features that captured recurring and crucial non-covalent receptor contacts and proposed three characteristics necessary for optimal zone-2 binding: a conserved pair of H bond acceptor (HBA to form H bond with Asn226 residue) and an aliphatic moiety of molecule separated by 3.75±0.44Å. Further, an aliphatic or a heterocyclic group distant (11.75±1.14Å) to the conserved aliphatic site formed the third feature component in the zone-2 specific anthelmintic pharmacophore model. Alternatively, an additional HBA can be substituted as a third component to establish H bonding with Asn204. We discern that selective zone-2 anthelmintics can be designed effectively by closely adapting the pharmacophore feature patterns and its geometrical constraints. Copyright © 2017 Elsevier Ltd. All rights reserved.

Handbook of Petroleum Processing

NASA Astrophysics Data System (ADS)

Jones, David S. J.; Pujado, Peter P.

This handbook describes and discusses the features that make up the petroleum refining industry. It begins with a description of the crude oils and their nature, and continues with the saleable products from the refining processes, with a review of the environmental impact. There is a complete overview of the processes that make up the refinery with a brief history of those processes.

A quality-refinement process for medical imaging applications.

PubMed

Neuhaus, J; Maleike, D; Nolden, M; Kenngott, H-G; Meinzer, H-P; Wolf, I

2009-01-01

To introduce and evaluate a process for refinement of software quality that is suitable to research groups. In order to avoid constraining researchers too much, the quality improvement process has to be designed carefully. The scope of this paper is to present and evaluate a process to advance quality aspects of existing research prototypes in order to make them ready for initial clinical studies. The proposed process is tailored for research environments and therefore more lightweight than traditional quality management processes. Focus on quality criteria that are important at the given stage of the software life cycle. Usage of tools that automate aspects of the process is emphasized. To evaluate the additional effort that comes along with the process, it was exemplarily applied for eight prototypical software modules for medical image processing. The introduced process has been applied to improve the quality of all prototypes so that they could be successfully used in clinical studies. The quality refinement yielded an average of 13 person days of additional effort per project. Overall, 107 bugs were found and resolved by applying the process. Careful selection of quality criteria and the usage of automated process tools lead to a lightweight quality refinement process suitable for scientific research groups that can be applied to ensure a successful transfer of technical software prototypes into clinical research workflows.

Application of the Sketch Match method in Sulina coastal study area within PEGASO project

NASA Astrophysics Data System (ADS)

Marin, Eugenia; Nichersu, Iuliana; Mierla, Marian; Trifanov, Cristian; Nichersu, Iulian

2013-04-01

The Sketch Match approach for Sulina pilot case was carried out in the frame of the project "People for Ecosystem Based Governance in Assessing Sustainable Development of Ocean and Coast" - PEGASO, funded by the Seventh Framework Programme. The PEGASO project has been designed to identify common threats and solutions in relation to the long-term sustainable development and environmental protection of coastal zones bordering the Mediterranean and Black Seas in ways relevant to the implementation of the Integrated Coastal Zone Management Protocol (ICZM) for the Mediterranean. PEGASO will use the model of the existing ICZM Protocol for the Mediterranean and adjust it to the needs of the Black Sea through innovative actions, one of them being Refine and develop efficient and easy to use tools for making sustainability assessments in the coastal zone tested through a number of relevant pilot sites. Thus, for the Romania case study, the Sketch Match approach was selected, being an interactive public participation planning method, developed by the Dutch Government, and applied for Sulina area in order to stimulate support and involvement from stakeholders regarding Integrated Coastal Zone Management Protocol by consulting and involving these people in the planning process and making use of a coherent package of interactive methods. Participants were representatives of a wide range of stakeholders, varying from local fisherman to representatives of the Local and County council and Danube Delta Biosphere Reserve Authority. They participated in a two-day design session, focused on problems and potentials of the area, with the aim to work out possible solutions for an integrated coastal spatial planning, focusing on the parallel enhance of the various local functions in the spatial design (coastal area protection next to industry, tourism, nature, recreation, and other activities).

Monitoring Sea Level in the Coastal Zone with Satellite Altimetry and Tide Gauges

NASA Astrophysics Data System (ADS)

Cipollini, Paolo; Calafat, Francisco M.; Jevrejeva, Svetlana; Melet, Angelique; Prandi, Pierre

2017-01-01

We examine the issue of sustained measurements of sea level in the coastal zone, first by summarizing the long-term observations from tide gauges, then showing how those are now complemented by improved satellite altimetry products in the coastal ocean. We present some of the progresses in coastal altimetry, both from dedicated reprocessing of the radar waveforms and from the development of improved corrections for the atmospheric effects. This trend towards better altimetric data at the coast comes also from technological innovations such as Ka-band altimetry and SAR altimetry, and we discuss the advantages deriving from the AltiKa Ka-band altimeter and the SIRAL altimeter on CryoSat-2 that can be operated in SAR mode. A case study along the UK coast demonstrates the good agreement between coastal altimetry and tide gauge observations, with root mean square differences as low as 4 cm at many stations, allowing the characterization of the annual cycle of sea level along the UK coasts. Finally, we examine the evolution of the sea level trend from the open to the coastal ocean along the western coast of Africa, comparing standard and coastally improved products. Different products give different sea level trend profiles, so the recommendation is that additional efforts are needed to study sea level trends in the coastal zone from past and present satellite altimeters. Further improvements are expected from more refined processing and screening of data, but in particular from the constant improvements in the geophysical corrections.

Border-oriented post-processing refinement on detected vehicle bounding box for ADAS

NASA Astrophysics Data System (ADS)

Chen, Xinyuan; Zhang, Zhaoning; Li, Minne; Li, Dongsheng

2018-04-01

We investigate a new approach for improving localization accuracy of detected vehicles for object detection in advanced driver assistance systems(ADAS). Specifically, we implement a bounding box refinement as a post-processing of the state-of-the-art object detectors (Faster R-CNN, YOLOv2, etc.). The bounding box refinement is achieved by individually adjusting each border of the detected bounding box to its target location using a regression method. We use HOG features which perform well on the edge detection of vehicles to train the regressor and the regressor is independent of the CNN-based object detectors. Experiment results on the KITTI 2012 benchmark show that we can achieve up to 6% improvements over YOLOv2 and Faster R-CNN object detectors on the IoU threshold of 0.8. Also, the proposed refinement framework is computationally light, allowing for processing one bounding box within a few milliseconds on CPU. Further, this refinement method can be added to any object detectors, especially those with high speed but less accuracy.

Use of mechanical refining to improve the production of low-cost sugars from lignocellulosic biomass.

PubMed

Park, Junyeong; Jones, Brandon; Koo, Bonwook; Chen, Xiaowen; Tucker, Melvin; Yu, Ju-Hyun; Pschorn, Thomas; Venditti, Richard; Park, Sunkyu

2016-01-01

Mechanical refining is widely used in the pulp and paper industry to enhance the end-use properties of products by creating external fibrillation and internal delamination. This technology can be directly applied to biochemical conversion processes. By implementing mechanical refining technology, biomass recalcitrance to enzyme hydrolysis can be overcome and carbohydrate conversion can be enhanced with commercially attractive levels of enzymes. In addition, chemical and thermal pretreatment severity can be reduced to achieve the same level of carbohydrate conversion, which reduces pretreatment cost and results in lower concentrations of inhibitors. Refining is versatile and a commercially proven technology that can be operated at process flows of ∼ 1500 dry tons per day of biomass. This paper reviews the utilization of mechanical refining in the pulp and paper industry and summarizes the recent development in applications for biochemical conversion, which potentially make an overall biorefinery process more economically viable. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study on the Removal of Gases in RH Refining Progress through Experiments Using Vacuum Induction Furnace

NASA Astrophysics Data System (ADS)

Niu, Deliang; Liu, Qingcai; Wang, Zhu; Ren, Shan; Lan, Yuanpei; Xu, Minren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining.

Techno-Economic Analysis of the Deacetylation and Disk Refining Process. Characterizing the Effect of Refining Energy and Enzyme Usage on Minimum Sugar Selling Price and Minimum Ethanol Selling Price

DOE PAGES

Chen, Xiaowen; Shekiro, Joseph; Pschorn, Thomas; ...

2015-10-29

A novel, highly efficient deacetylation and disk refining (DDR) process to liberate fermentable sugars from biomass was recently developed at the National Renewable Energy Laboratory (NREL). The DDR process consists of a mild, dilute alkaline deacetylation step followed by low-energy-consumption disk refining. The DDR corn stover substrates achieved high process sugar conversion yields, at low to modest enzyme loadings, and also produced high sugar concentration syrups at high initial insoluble solid loadings. The sugar syrups derived from corn stover are highly fermentable due to low concentrations of fermentation inhibitors. The objective of this work is to evaluate the economic feasibilitymore » of the DDR process through a techno-economic analysis (TEA). A large array of experiments designed using a response surface methodology was carried out to investigate the two major cost-driven operational parameters of the novel DDR process: refining energy and enzyme loadings. The boundary conditions for refining energy (128–468 kWh/ODMT), cellulase (Novozyme’s CTec3) loading (11.6–28.4 mg total protein/g of cellulose), and hemicellulase (Novozyme’s HTec3) loading (0–5 mg total protein/g of cellulose) were chosen to cover the most commercially practical operating conditions. The sugar and ethanol yields were modeled with good adequacy, showing a positive linear correlation between those yields and refining energy and enzyme loadings. The ethanol yields ranged from 77 to 89 gallons/ODMT of corn stover. The minimum sugar selling price (MSSP) ranged from $0.191 to $0.212 per lb of 50 % concentrated monomeric sugars, while the minimum ethanol selling price (MESP) ranged from $2.24 to $2.54 per gallon of ethanol. The DDR process concept is evaluated for economic feasibility through TEA. The MSSP and MESP of the DDR process falls within a range similar to that found with the deacetylation/dilute acid pretreatment process modeled in NREL’s 2011 design report. The DDR process is a much simpler process that requires less capital and maintenance costs when compared to conventional chemical pretreatments with pressure vessels. As a result, we feel the DDR process should be considered as an option for future biorefineries with great potential to be more cost-effective.« less

Techno-Economic Analysis of the Deacetylation and Disk Refining Process. Characterizing the Effect of Refining Energy and Enzyme Usage on Minimum Sugar Selling Price and Minimum Ethanol Selling Price

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiaowen; Shekiro, Joseph; Pschorn, Thomas

A novel, highly efficient deacetylation and disk refining (DDR) process to liberate fermentable sugars from biomass was recently developed at the National Renewable Energy Laboratory (NREL). The DDR process consists of a mild, dilute alkaline deacetylation step followed by low-energy-consumption disk refining. The DDR corn stover substrates achieved high process sugar conversion yields, at low to modest enzyme loadings, and also produced high sugar concentration syrups at high initial insoluble solid loadings. The sugar syrups derived from corn stover are highly fermentable due to low concentrations of fermentation inhibitors. The objective of this work is to evaluate the economic feasibilitymore » of the DDR process through a techno-economic analysis (TEA). A large array of experiments designed using a response surface methodology was carried out to investigate the two major cost-driven operational parameters of the novel DDR process: refining energy and enzyme loadings. The boundary conditions for refining energy (128–468 kWh/ODMT), cellulase (Novozyme’s CTec3) loading (11.6–28.4 mg total protein/g of cellulose), and hemicellulase (Novozyme’s HTec3) loading (0–5 mg total protein/g of cellulose) were chosen to cover the most commercially practical operating conditions. The sugar and ethanol yields were modeled with good adequacy, showing a positive linear correlation between those yields and refining energy and enzyme loadings. The ethanol yields ranged from 77 to 89 gallons/ODMT of corn stover. The minimum sugar selling price (MSSP) ranged from $0.191 to $0.212 per lb of 50 % concentrated monomeric sugars, while the minimum ethanol selling price (MESP) ranged from $2.24 to $2.54 per gallon of ethanol. The DDR process concept is evaluated for economic feasibility through TEA. The MSSP and MESP of the DDR process falls within a range similar to that found with the deacetylation/dilute acid pretreatment process modeled in NREL’s 2011 design report. The DDR process is a much simpler process that requires less capital and maintenance costs when compared to conventional chemical pretreatments with pressure vessels. As a result, we feel the DDR process should be considered as an option for future biorefineries with great potential to be more cost-effective.« less

Techno-economic analysis of the deacetylation and disk refining process: characterizing the effect of refining energy and enzyme usage on minimum sugar selling price and minimum ethanol selling price.

PubMed

Chen, Xiaowen; Shekiro, Joseph; Pschorn, Thomas; Sabourin, Marc; Tucker, Melvin P; Tao, Ling

2015-01-01

A novel, highly efficient deacetylation and disk refining (DDR) process to liberate fermentable sugars from biomass was recently developed at the National Renewable Energy Laboratory (NREL). The DDR process consists of a mild, dilute alkaline deacetylation step followed by low-energy-consumption disk refining. The DDR corn stover substrates achieved high process sugar conversion yields, at low to modest enzyme loadings, and also produced high sugar concentration syrups at high initial insoluble solid loadings. The sugar syrups derived from corn stover are highly fermentable due to low concentrations of fermentation inhibitors. The objective of this work is to evaluate the economic feasibility of the DDR process through a techno-economic analysis (TEA). A large array of experiments designed using a response surface methodology was carried out to investigate the two major cost-driven operational parameters of the novel DDR process: refining energy and enzyme loadings. The boundary conditions for refining energy (128-468 kWh/ODMT), cellulase (Novozyme's CTec3) loading (11.6-28.4 mg total protein/g of cellulose), and hemicellulase (Novozyme's HTec3) loading (0-5 mg total protein/g of cellulose) were chosen to cover the most commercially practical operating conditions. The sugar and ethanol yields were modeled with good adequacy, showing a positive linear correlation between those yields and refining energy and enzyme loadings. The ethanol yields ranged from 77 to 89 gallons/ODMT of corn stover. The minimum sugar selling price (MSSP) ranged from $0.191 to $0.212 per lb of 50 % concentrated monomeric sugars, while the minimum ethanol selling price (MESP) ranged from $2.24 to $2.54 per gallon of ethanol. The DDR process concept is evaluated for economic feasibility through TEA. The MSSP and MESP of the DDR process falls within a range similar to that found with the deacetylation/dilute acid pretreatment process modeled in NREL's 2011 design report. The DDR process is a much simpler process that requires less capital and maintenance costs when compared to conventional chemical pretreatments with pressure vessels. As a result, we feel the DDR process should be considered as an option for future biorefineries with great potential to be more cost-effective.

Solidification Based Grain Refinement in Steels

DTIC Science & Technology

2009-07-24

pearlite (See Figure 1). No evidence of the as-cast austenite dendrite structure was observed. The gating system for this sample resides at the thermal...possible nucleating compounds. 3) Extend grain refinement theory and solidification knowledge through experimental data. 4) Determine structure ...refine the structure of a casting through heat treatment. The energy required for grain refining via thermomechanical processes or heat treatment

Thermal regime of an ice-wedge polygon landscape near Barrow, Alaska

NASA Astrophysics Data System (ADS)

Daanen, R. P.; Liljedahl, A. K.

2017-12-01

Tundra landscapes are changing all over the circumpolar Arctic due to permafrost degradation. Soil cracking and infilling of meltwater repeated over thousands of years form ice wedges, which produce the characteristic surface pattern of ice-wedge polygon tundra. Rapid top-down thawing of massive ice leads to differential ground subsidence and sets in motion a series of short- and long-term hydrological and ecological changes. Subsequent responses in the soil thermal regime drive further permafrost degradation and/or stabilization. Here we explore the soil thermal regime of an ice-wedge polygon terrain near Utqiagvik (formerly Barrow) with the Water balance Simulation Model (WaSiM). WaSiM is a hydro-thermal model developed to simulate the water balance at the watershed scale and was recently refined to represent the hydrological processes unique to cold climates. WaSiM includes modules that represent surface runoff, evapotranspiration, groundwater, and soil moisture, while active layer freezing and thawing is based on a direct coupling of hydrological and thermal processes. A new snow module expands the vadose zone calculations into the snow pack, allowing the model to simulate the snow as a porous medium similar to soil. Together with a snow redistribution algorithm based on local topography, this latest addition to WaSiM makes simulation of the ground thermal regime much more accurate during winter months. Effective representation of ground temperatures during winter is crucial in the simulation of the permafrost thermal regime and allows for refined predictions of future ice-wedge degradation or stabilization.

New Insights on Degumming and Bleaching Process Parameters on The Formation of 3-Monochloropropane-1,2-Diol Esters and Glycidyl Esters in Refined, Bleached, Deodorized Palm Oil.

PubMed

Sim, Biow Ing; Muhamad, Halimah; Lai, Oi Ming; Abas, Faridah; Yeoh, Chee Beng; Nehdi, Imededdine Arbi; Khor, Yih Phing; Tan, Chin Ping

2018-04-01

This paper examines the interactions of degumming and bleaching processes as well as their influences on the formation of 3-monochloropropane-1,2-diol esters (3-MCPDE) and glycidyl esters in refined, bleached and deodorized palm oil by using D-optimal design. Water degumming effectively reduced the 3-MCPDE content up to 50%. Acid activated bleaching earth had a greater effect on 3-MCPDE reduction compared to natural bleaching earth and acid activated bleaching earth with neutral pH, indicating that performance and adsorption capacities of bleaching earth are the predominant factors in the removal of esters, rather than its acidity profile. The combination of high dosage phosphoric acid during degumming with the use of acid activated bleaching earth eliminated almost all glycidyl esters during refining. Besides, the effects of crude palm oil quality was assessed and it was found that the quality of crude palm oil determines the level of formation of 3-MCPDE and glycidyl esters in palm oil during the high temperature deodorization step of physical refining process. Poor quality crude palm oil has strong impact towards 3-MCPDE and glycidyl esters formation due to the intrinsic components present within. The findings are useful to palm oil refining industry in choosing raw materials as an input during the refining process.

Model of Silicon Refining During Tapping: Removal of Ca, Al, and Other Selected Element Groups

NASA Astrophysics Data System (ADS)

Olsen, Jan Erik; Kero, Ida T.; Engh, Thorvald A.; Tranell, Gabriella

2017-04-01

A mathematical model for industrial refining of silicon alloys has been developed for the so-called oxidative ladle refining process. It is a lumped (zero-dimensional) model, based on the mass balances of metal, slag, and gas in the ladle, developed to operate with relatively short computational times for the sake of industrial relevance. The model accounts for a semi-continuous process which includes both the tapping and post-tapping refining stages. It predicts the concentrations of Ca, Al, and trace elements, most notably the alkaline metals, alkaline earth metal, and rare earth metals. The predictive power of the model depends on the quality of the model coefficients, the kinetic coefficient, τ, and the equilibrium partition coefficient, L for a given element. A sensitivity analysis indicates that the model results are most sensitive to L. The model has been compared to industrial measurement data and found to be able to qualitatively, and to some extent quantitatively, predict the data. The model is very well suited for alkaline and alkaline earth metals which respond relatively fast to the refining process. The model is less well suited for elements such as the lanthanides and Al, which are refined more slowly. A major challenge for the prediction of the behavior of the rare earth metals is that reliable thermodynamic data for true equilibrium conditions relevant to the industrial process is not typically available in literature.

Catalytic coal liquefaction with treated solvent and SRC recycle

DOEpatents

Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

1986-01-01

A process for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal.

Tearing, segmentation, and backstepping of subduction in the Aegean: New insights from seismicity

NASA Astrophysics Data System (ADS)

Bocchini, G. M.; Brüstle, A.; Becker, D.; Meier, T.; van Keken, P. E.; Ruscic, M.; Papadopoulos, G. A.; Rische, M.; Friederich, W.

2018-06-01

This study revisits subduction processes at the Hellenic Subduction Zone (HSZ) including tearing, segmentation, and backstepping, by refining the geometry of the Nubian slab down to 150-180 km depth using well-located hypocentres from global and local seismicity catalogues. At the western termination of the HSZ, the Kefalonia Transform Fault marks the transition between oceanic and continental lithosphere subducting to the south and to the north of it, respectively. A discontinuity is suggested to exist between the two slabs at shallow depths. The Kefalonia Transform Fault is interpreted as an active Subduction-Transform-Edge-Propagator-fault formed as consequence of faster trench retreat induced by the subduction of oceanic lithosphere to the south of it. A model reconstructing the evolution of the subduction system in the area of Peloponnese since 34 Ma, involving the backstepping of the subduction to the back-side of Adria, provides seismological evidence that supports the single-slab model for the HSZ and suggests the correlation between the downdip limit of the seismicity to the amount of subducted oceanic lithosphere. In the area of Rhodes, earthquake hypocentres indicate the presence of a NW dipping subducting slab that rules out the presence of a NE-SW striking Subduction-Transform-Edge-Propagator-fault in the Pliny-Strabo trenches region. Earthquake hypocentres also allow refining the slab tear beneath southwestern Anatolia down to 150-180 km depth. Furthermore, the distribution of microseismicity shows a first-order slab segmentation in the region between Crete and Karpathos, with a less steep and laterally wider slab segment to the west and a steeper and narrower slab segment to the east. Thermal models indicate the presence of a colder slab beneath the southeastern Aegean that leads to deepening of the intermediate-depth seismicity. Slab segmentation affects the upper plate deformation that is stronger above the eastern slab segment and the seismicity along the interplate seismogenic zone.

Ambient and high pressure single crystal x-ray studies of pyrope and synthetic ferric majorite

NASA Astrophysics Data System (ADS)

Smith, Henrietta Mercer

The mineral garnet is widely accepted as a major constituent of Earth's upper mantle and transition zone. As such, understanding of the state of the material at high pressures and temperatures will increase our ability to correlate seismic data with the mineralogy in these regions of Earth's interior. Studies of varied compositions of garnet at ambient conditions may enhance our understanding of solid-solution energetics, and yield predictive power concerning element partitioning among various minerals at different depths within Earth. This study began with structure refinements at ambient conditions of eighteen natural and two synthetic garnets, nominally in the pyrope-grossular-almandine ternary system. The natural, nearly-pure pyrope sample of this group was then used in developing the techniques necessary for high-pressure structure refinements. For high pressure work, a diamond anvil pressure cell (DAC) was loaded with the sample and mounted on an 18 kW rotating anode four-circle diffractometer. Unit cells and oxygen positional parameters of the pyrope sample were refined at five pressures to 9.9 GPa. The data were in agreement with those of other studies, and extended by 40% the pressure range achieved previously. The zero-pressure bulk modulus, K = 176 GPa, with Ksp' = dK/dP = 4. Following the high pressure pyrope study, synthetic samples of Fe-bearing majoritic garnet became available. These samples are of particular interest because they were grown at transition zone conditions and coexisted with a hydrous wadsleyite phase. The hydration state of earth's mantle is a topic of much current research, and samples such as these will provide information necessary to the placement of constraints on the degree of hydration actually present. The structures of five majorite samples from three different synthesis runs were refined at ambient conditions, and two of these samples were analyzed using Mossbauer spectroscopy. Fesp{3+}/SigmaFe ranged from 85-95%. One sample, for which there were both X-ray and Mossbauer data, was loaded into a DAC. The structure was refined at ten pressures to 12.9 GPa. K = 172.5 GPa with Ksp{''} = 4. The bulk compression is nearly identical to that of pyrope, but the compressions of the coordination polyhedra are quite different.

A general ionic liquid pH-zone-refining countercurrent chromatography method for separation of alkaloids from Nelumbo nucifera Gaertn.

PubMed

Fang, Yingtong; Li, Quan; Shao, Qian; Wang, Binghai; Wei, Yun

2017-07-21

The alkaloids from lotus (Nelumbo nucifera Gaertn) are effective in lowering hyperlipemia and level of cholesterol. However, there is not a general method for their separation. In this work, a general ionic liquid pH-zone-refining countercurrent chromatography method for isolation and purification of six alkaloids from the whole lotus plant was successfully established by using ionic liquids as the modifier of the two-phase solvent system. The conditions of ionic liquid pH-zone-refining countercurrent chromatography, involving solvent systems, concentration of retainer and eluter, types of ionic liquids, the content of ionic liquids as well as ionic liquids posttreatment, were optimized to improve extraction efficiency. Finally, the separation of these six alkaloids was performed with a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water-[C 4 mim][PF 6 ] at a volume ratio of 5:2:2:8:0.1, where 10mM TEA was added to the organic stationary phase as a retainer and 3mM HCl was added to the aqueous mobile phase as an eluter. As a result, six alkaloids including N-nornuciferine, liensinine, nuciferine, isoliensinine, roemerine and neferine were successfully separated with the purities of 97.0%, 90.2%, 94.7%, 92.8%, 90.4% and 95.9%, respectively. The established general method has been respectively applied to the crude samples of lotus leaves and lotus plumules. A total of 37.3mg of liensinine, 57.7mg of isoliensinine and 179.9mg of neferine were successfully purified in one run from 1.00g crude extract of lotus plumule with the purities of 93.2%, 96.5% and 98.8%, respectively. Amount of 45.6mg N-nornuciferine, 21.6mg nuciferine and 11.7mg roemerine was obtained in one step separation from 1.05g crude extract of lotus leaves with the purity of 96.9%, 95.6% and 91.33%, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

Embedding ecosystem services in coastal planning leads to better outcomes for people and nature

PubMed Central

Arkema, Katie K.; Verutes, Gregory M.; Wood, Spencer A.; Clarke-Samuels, Chantalle; Rosado, Samir; Canto, Maritza; Rosenthal, Amy; Ruckelshaus, Mary; Guannel, Gregory; Toft, Jodie; Faries, Joe; Silver, Jessica M.; Griffin, Robert; Guerry, Anne D.

2015-01-01

Recent calls for ocean planning envision informed management of social and ecological systems to sustain delivery of ecosystem services to people. However, until now, no coastal and marine planning process has applied an ecosystem-services framework to understand how human activities affect the flow of benefits, to create scenarios, and to design a management plan. We developed models that quantify services provided by corals, mangroves, and seagrasses. We used these models within an extensive engagement process to design a national spatial plan for Belize’s coastal zone. Through iteration of modeling and stakeholder engagement, we developed a preferred plan, currently under formal consideration by the Belizean government. Our results suggest that the preferred plan will lead to greater returns from coastal protection and tourism than outcomes from scenarios oriented toward achieving either conservation or development goals. The plan will also reduce impacts to coastal habitat and increase revenues from lobster fishing relative to current management. By accounting for spatial variation in the impacts of coastal and ocean activities on benefits that ecosystems provide to people, our models allowed stakeholders and policymakers to refine zones of human use. The final version of the preferred plan improved expected coastal protection by >25% and more than doubled the revenue from fishing, compared with earlier versions based on stakeholder preferences alone. Including outcomes in terms of ecosystem-service supply and value allowed for explicit consideration of multiple benefits from oceans and coasts that typically are evaluated separately in management decisions. PMID:26082545

Embedding ecosystem services in coastal planning leads to better outcomes for people and nature.

PubMed

Arkema, Katie K; Verutes, Gregory M; Wood, Spencer A; Clarke-Samuels, Chantalle; Rosado, Samir; Canto, Maritza; Rosenthal, Amy; Ruckelshaus, Mary; Guannel, Gregory; Toft, Jodie; Faries, Joe; Silver, Jessica M; Griffin, Robert; Guerry, Anne D

2015-06-16

Recent calls for ocean planning envision informed management of social and ecological systems to sustain delivery of ecosystem services to people. However, until now, no coastal and marine planning process has applied an ecosystem-services framework to understand how human activities affect the flow of benefits, to create scenarios, and to design a management plan. We developed models that quantify services provided by corals, mangroves, and seagrasses. We used these models within an extensive engagement process to design a national spatial plan for Belize's coastal zone. Through iteration of modeling and stakeholder engagement, we developed a preferred plan, currently under formal consideration by the Belizean government. Our results suggest that the preferred plan will lead to greater returns from coastal protection and tourism than outcomes from scenarios oriented toward achieving either conservation or development goals. The plan will also reduce impacts to coastal habitat and increase revenues from lobster fishing relative to current management. By accounting for spatial variation in the impacts of coastal and ocean activities on benefits that ecosystems provide to people, our models allowed stakeholders and policymakers to refine zones of human use. The final version of the preferred plan improved expected coastal protection by >25% and more than doubled the revenue from fishing, compared with earlier versions based on stakeholder preferences alone. Including outcomes in terms of ecosystem-service supply and value allowed for explicit consideration of multiple benefits from oceans and coasts that typically are evaluated separately in management decisions.

Development of a special approach of the mineralization localization zones prediction based on the combination and the geoinformation analysis of heterogeneous geodata

NASA Astrophysics Data System (ADS)

Ivanova, Julia

2014-05-01

The complexity of any task solving, including tasks in the Earth Sciences, depends on the completeness of the information that is available. The prediction of the mineralization zone localization is a task with incomplete information. The tasks of prediction are complicated because of search data difficult formalize, and the absent of single information structures of the representation of the search data. These facts complicate the process of structuring, processing and analysis of information. Geodata that need to process are presented in various formats: raster two-dimensional and three-dimensional fields, vector layers of polygons and lines, point markable layers, the spectral and discrete, quantized and continuous, analog and digital forms, as well as chemical formalization. In this form representative data cannot be combining into superclasses. At the same time the information content of geodata that are applied individually is very small. While a number of low informative features, which can be obtained in the process of research of mineralization zones are usually redundant. As a result the quality of knowledge that can be obtained from the search data decreases, as well as the technological cycle of information processing increases. Additionally, that leads to exploitation of datasets, and production of large shared datasets [1]. To solve efficiently the tasks of predicting, it is necessary to use union heterogeneous search features, accumulated factual data and modern science-based mathematical apparatus of processing and analysis of the information. As well young branches of human knowledge help to solve this task: remote sensing, geoinformatics, Earth and Space Science Informatics [2], apparatus of catastrophe theory and nonlinear dynamics, game theory. The purpose of the suggested approach is to increase informational content, and to reduce of geodata redundancy to improve the accuracy of the prediction of mineralization zones. The developed algorithm of prediction of the localization of mineralization zone consists of the some steps: 1. The collection of information about the studying territory of upcoming work from various sources, i.e. building of database (DB). The DB includes variety geodata. 2. The formalization, the concatenation and the union of geodata. Study of features correlation characteristics. Generation of new formal and functional search features. 3. The formation of a number of hypotheses based on initial data. The refinement of search features. 4. Preliminary mathematical modeling of prospective mineralized zones. The study of obtained results, the formation of additional features list. 5. The collection of additional features by field methods for verifying of hypotheses. 6. Processing and analyzing of obtaining data, the specification of preliminary mathematical model. 7. The examination of hypotheses using the obtained results. The study of prediction errors. 8. Building of multidimensional risk matrices of detection and bifurcation diagrams of mineralization [3]. 9. The final mathematical modeling of perspective mineralized zones. Thus, the proposed approach allows to increase the information content of geodata significantly, to reduce redundancy of geodate, and to increase the accuracy of predicting zones of gold mineralization. Currently the approach, suggested by the author, applies for prediction of the localization of gold mineralization at the territory of the Polar Urals. References: 1.W. J. Som de Cerff, M. Petitdidier, A. Gemünd, L. Horstink, H. Schwichtenberg, Earth Science Test Suites to Evaluate Grid Tools and Middleware-Examples for Grid Data Access Tools, Earth Science Informatics, Vol. 2, 117-131, 2009. DOI 10.1007/s12145-009-0022-y. 2. P. Mazzetti , S. Nativi, J. Caron, RESTfulI implementation of Geospatial, Services for Earth and Space Science Applications, International Journal of Digital Earth, Vol. 2, Supplement 1, 40-61, 2009. DOI: 10.1080/175389409028661532. 3. Arnold V.I., Catastrophe Theory, 4th ed. Moscow, Editorial-URSS (2004), ISBN 5-354-00674-0 (in Russian).

Exoplanets, extremophiles and habitability

NASA Astrophysics Data System (ADS)

Janot Pacheco, E.; Bernardes, L.

2012-09-01

Estimates of the average surface temperature and CO2 partial atmospheric pressure of already discovered exoplanets supposed to be in their Habitable Zone of their stars were surveyed from the Exoplanet Encyclopedia database. Moreover, since planetary surface temperature strongly depends on its albedo and geodynamic conditions, we have been feeding exoplanetary data into a comprehensive model of Earth's atmosphere to get better estimations. We also investigated the possible presence of "exomoons" belonging to giant planets capable of harbour dynamic stability and to retain atmospheric layers and keep geodynamic activity for long time spans. Collected information on biological data of micro-organisms classified as "extremophiles" indicate that such kind of microbial species could dwell in many of them. We thus propose an extension of the more astronomically defined "Habitable Zone" concept into the more astrobiologically "Extremophile Zone", taking into account other refined parameters allowing survival of more robust life forms.

Ground-motion prediction from tremor

USGS Publications Warehouse

Baltay, Annemarie S.; Beroza, Gregory C.

2013-01-01

The widespread occurrence of tremor, coupled with its frequency content and location, provides an exceptional opportunity to test and improve strong ground-motion attenuation relations for subduction zones. We characterize the amplitude of thousands of individual 5 min tremor events in Cascadia during three episodic tremor and slip events to constrain the distance decay of peak ground acceleration (PGA) and peak ground velocity (PGV). We determine the anelastic attenuation parameter for ground-motion prediction equations (GMPEs) to a distance of 150 km, which is sufficient to place important constraints on ground-motion decay. Tremor PGA and PGV show a distance decay that is similar to subduction-zone-specific GMPEs developed from both data and simulations; however, the massive amount of data present in the tremor observations should allow us to refine distance-amplitude attenuation relationships for use in hazard maps, and to search for regional variations and intrasubduction zone differences in ground-motion attenuation.

Chromatographic separation of the platinum-group elements, gold, base metals and sulfur during degassing of a compacting and solidifying igneous crystal pile

NASA Astrophysics Data System (ADS)

Boudreau, A. E.; Meurer, W. P.

The major platinum-group elements (PGE) concentrations in layered intrusions are typically associated with zones in which the sulfide abundance begins to increase. In a number of layered intrusions, there is also a distinct stratigraphic separation in the peak concentrations of the PGE from those of the base metals, gold and sulfur through these zones. These stratigraphic ``offsets'' are characterized by a lower, typically S-poor, Pt- and Pd-enriched zone overlain by a zone enriched in the base metals, S and Au. The separations amount to a few decimeters to several tens of meters. In some instances, the high Pt and Pd concentrations are associated with trivial amounts of sulfide. Theoretical considerations suggest that these offsets can be modeled as chromatographic peaks that develop during an infiltration/reaction process. Using Pd as a typical PGE and Cu as a typical base metal, a numeric model is developed that illustrates how metal separations can develop in a vapor-refining zone as fluid evolved during solidification of a cumulus pile leaches sulfide and redeposits it higher in the crystal pile. The solidification/degassing ore-element transport is coupled with a compaction model for the crystal pile. Solidification resulting from conductive cooling through the base of the compacting column leads to an increasing volatile concentration in the intercumulus liquid until it reaches fluid saturation. Separation and upward migration of this fluid lead to an upward-migrating zone of increasingly higher bulk water contents as water degassed from underlying cumulates enriches overlying, fluid-undersaturated interstitial liquids. Sulfide is resorbed from the degassing regions and is reprecipitated in these vapor-undersaturated interstitial liquids, producing a zone of relatively high modal sulfide that also migrates upward with time. Owing to its strong preference for sulfide, Pd is not significantly mobile until all sulfide is resorbed. The result is a zone of increasing PGE enrichment that follows the sulfide resorption front as solidification/degassing continues. In detail, the highest Pd concentrations occur stratigraphically below the peak in S and base metals. The high Pd/S ratio mimics values conventionally interpreted as the result of high (silicate liquid)/(sulfide liquid) mass ratios (``R'' values). However, in this case, the high Pd/S ratio is the result of a chromatographic/reaction front enrichment and not a magmatic sulfide-saturation event.

Processing and refinement of steel microstructure images for assisting in computerized heat treatment of plain carbon steel

NASA Astrophysics Data System (ADS)

Gupta, Shubhank; Panda, Aditi; Naskar, Ruchira; Mishra, Dinesh Kumar; Pal, Snehanshu

2017-11-01

Steels are alloys of iron and carbon, widely used in construction and other applications. The evolution of steel microstructure through various heat treatment processes is an important factor in controlling properties and performance of steel. Extensive experimentations have been performed to enhance the properties of steel by customizing heat treatment processes. However, experimental analyses are always associated with high resource requirements in terms of cost and time. As an alternative solution, we propose an image processing-based technique for refinement of raw plain carbon steel microstructure images, into a digital form, usable in experiments related to heat treatment processes of steel in diverse applications. The proposed work follows the conventional steps practiced by materials engineers in manual refinement of steel images; and it appropriately utilizes basic image processing techniques (including filtering, segmentation, opening, and clustering) to automate the whole process. The proposed refinement of steel microstructure images is aimed to enable computer-aided simulations of heat treatment of plain carbon steel, in a timely and cost-efficient manner; hence it is beneficial for the materials and metallurgy industry. Our experimental results prove the efficiency and effectiveness of the proposed technique.

B Removal by Zr Addition in Electromagnetic Solidification Refinement of Si with Si-Al Melt

NASA Astrophysics Data System (ADS)

Lei, Yun; Ma, Wenhui; Sun, Luen; Dai, Yongnian; Morita, Kazuki

2016-02-01

This study investigated a new process of enhancing B removal by adding small amounts of Zr in the electromagnetic solidification refinement of Si with Si-Al melt. B in Si was removed by as much as 97.2 pct by adding less than 1057 ppma Zr, and the added Zr was removed by as much as 99.7 pct. In addition, Zr is more effective in enhancing B removal than Ti in the same electromagnetic solidification refining process.

Oxygen-Induced Cracking Distillation of Oil in the Continuous Flow Tank Reactor

ERIC Educational Resources Information Center

Shvets, Valeriy F.; Kozlovskiy, Roman A.; Luganskiy, Artur I.; Gorbunov, Andrey V.; Suchkov, Yuriy P.; Ushin, Nikolay S.; Cherepanov, Alexandr A.

2016-01-01

The article analyses problems of processing black oil fuel and addresses the possibility of increasing the depth of oil refining by a new processing scheme. The study examines various methods of increasing the depth of oil refining reveals their inadequacies and highlights a need to introduce a new method of processing atmospheric and vacuum…

40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

40 CFR 409.20 - Applicability; description of the crystalline cane sugar refining subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... crystalline cane sugar refining subcategory. 409.20 Section 409.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Crystalline Cane Sugar Refining Subcategory § 409.20 Applicability; description of the crystalline cane sugar...

40 CFR 80.92 - Baseline auditor requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... total of more than 10 percent of its net worth with the refiner or importer; nor (iii) Receive... determination. It shall have personnel familiar with petroleum refining processes, including associated... worked at least five (5) years in either refinery operations or as a consultant for the refining industry...

40 CFR 80.92 - Baseline auditor requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... total of more than 10 percent of its net worth with the refiner or importer; nor (iii) Receive... determination. It shall have personnel familiar with petroleum refining processes, including associated... worked at least five (5) years in either refinery operations or as a consultant for the refining industry...

40 CFR 80.92 - Baseline auditor requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... total of more than 10 percent of its net worth with the refiner or importer; nor (iii) Receive... determination. It shall have personnel familiar with petroleum refining processes, including associated... worked at least five (5) years in either refinery operations or as a consultant for the refining industry...

Weak imposition of frictionless contact constraints on automatically recovered high-order, embedded interfaces using the finite cell method

NASA Astrophysics Data System (ADS)

Bog, Tino; Zander, Nils; Kollmannsberger, Stefan; Rank, Ernst

2018-04-01

The finite cell method (FCM) is a fictitious domain approach that greatly simplifies simulations involving complex structures. Recently, the FCM has been applied to contact problems. The current study continues in this field by extending the concept of weakly enforced boundary conditions to inequality constraints for frictionless contact. Furthermore, it formalizes an approach that automatically recovers high-order contact surfaces of (implicitly defined) embedded geometries by means of an extended Marching Cubes algorithm. To further improve the accuracy of the discretization, irregularities at the boundary of contact zones are treated with multi-level hp-refinements. Numerical results and a systematic study of h-, p- and hp-refinements show that the FCM can efficiently provide accurate results for problems involving contact.

Catalytic coal liquefaction with treated solvent and SRC recycle

DOEpatents

Garg, D.; Givens, E.N.; Schweighardt, F.K.

1986-12-09

A process is described for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal. 2 figs.

Analysing the strength of friction stir welded dissimilar aluminium alloys using Sugeno Fuzzy model

NASA Astrophysics Data System (ADS)

Barath, V. R.; Vaira Vignesh, R.; Padmanaban, R.

2018-02-01

Friction stir welding (FSW) is a promising solid state joining technique for aluminium alloys. In this study, FSW trials were conducted on two dissimilar plates of aluminium alloy AA2024 and AA7075 by varying the tool rotation speed (TRS) and welding speed (WS). Tensile strength (TS) of the joints were measured and a Sugeno - Fuzzy model was developed to interconnect the FSW process parameters with the tensile strength. From the developed model, it was observed that the optimum heat generation at WS of 15 mm.min-1 and TRS of 1050 rpm resulted in dynamic recovery and dynamic recrystallization of the material. This refined the grains in the FSW zone and resulted in peak tensile strength among the tested specimens. Crest parabolic trend was observed in tensile strength with variation of TRS from 900 rpm to 1200 rpm and TTS from 10 mm.min-1 to 20 mm.min-1.

The Scientific and Societal Need for Accurate Global Remote Sensing of Marine Suspended Sediments

NASA Technical Reports Server (NTRS)

Acker, James G.

2006-01-01

Population pressure, commercial development, and climate change are expected to cause continuing alteration of the vital oceanic coastal zone environment. These pressures will influence both the geology and biology of the littoral, nearshore, and continental shelf regions. A pressing need for global observation of coastal change processes is an accurate remotely-sensed data product for marine suspended sediments. The concentration, delivery, transport, and deposition of sediments is strongly relevant to coastal primary production, inland and coastal hydrology, coastal erosion, and loss of fragile wetland and island habitats. Sediment transport and deposition is also related to anthropogenic activities including agriculture, fisheries, aquaculture, harbor and port commerce, and military operations. Because accurate estimation of marine suspended sediment concentrations requires advanced ocean optical analysis, a focused collaborative program of algorithm development and assessment is recommended, following the successful experience of data refinement for remotely-sensed global ocean chlorophyll concentrations.

Inherited crustal deformation along the East Gondwana margin revealed by seismic anisotropy tomography

NASA Astrophysics Data System (ADS)

Pilia, S.; Arroucau, P.; Rawlinson, N.; Reading, A. M.; Cayley, R. A.

2016-12-01

The mechanisms of continental growth are a crucial part of plate tectonic theory, yet a clear understanding of the processes involved remains elusive. Here we determine seismic Rayleigh wave phase anisotropy variations in the crust beneath the southern Tasmanides of Australia, a Paleozoic accretionary margin. Our results reveal a complex, thick-skinned pervasive deformation that was driven by the tectonic interaction between the proto-Pacific Ocean and the ancient eastern margin of Gondwana. Stress-induced effects triggered by the collision and entrainment of a microcontinent into the active subduction zone are evident in the anisotropy signature. The paleofracturing trend of failed rifting between Australia and Antarctica is also recorded in the anisotropy pattern as well as a tightly curved feature in central Tasmania. The observed patterns of anisotropy correlate well with recent geodynamic and kinematic models of the Tasmanides and provide a platform from which the spatial extent of deformational domains can be refined.

Characterization of Multilayered Multipass Friction Stir Weld on ASTM A572 G50 Steel

DOE PAGES

Lim, Yong Chae; Sanderson, Samuel; Mahoney, Murray; ...

2014-01-01

A multilayered multipass friction stir weld (MM-FSW) on ASTM A572 Grade 50 steel was characterized to understand its potential application for thick-section structures. The 15-mm-thick section was fabricated by stacking up three steel plates and then friction stir welding the plates together in a total of 5 passes. The unique butt/lap joint configuration encountered in the multilayer weld was examined to understand the effect of tool rotation direction on the joint quality especially the formation of hooking defect. Charpy V-notch impact toughness tests showed generally higher impact toughness energy for the stir zone than the base metal with a ductilemore » fracture mode. The microhardness value was measured from 195 to 220 HV in the stir zone, while the base metal showed an average value of 170 HV. The microstructure in the stir zone and the adjacent heat affected zone was quantified using Optical and Scanning Electron Microscopy (SEM) including Electron Backscatter Diffraction (EBSD). The increased toughness and hardness were correlated with the refined microstructure in stir zone, resulting from severe plastic deformation and subsequent dynamic recrystallization during friction stir welding.« less

Microstructures and Grain Refinement of Additive-Manufactured Ti- xW Alloys

NASA Astrophysics Data System (ADS)

Mendoza, Michael Y.; Samimi, Peyman; Brice, David A.; Martin, Brian W.; Rolchigo, Matt R.; LeSar, Richard; Collins, Peter C.

2017-07-01

It is necessary to better understand the composition-processing-microstructure relationships that exist for materials produced by additive manufacturing. To this end, Laser Engineered Net Shaping (LENS™), a type of additive manufacturing, was used to produce a compositionally graded titanium binary model alloy system (Ti- xW specimen (0 ≤ x ≤ 30 wt pct), so that relationships could be made between composition, processing, and the prior beta grain size. Importantly, the thermophysical properties of the Ti- xW, specifically its supercooling parameter ( P) and growth restriction factor ( Q), are such that grain refinement is expected and was observed. The systematic, combinatorial study of this binary system provides an opportunity to assess the mechanisms by which grain refinement occurs in Ti-based alloys in general, and for additive manufacturing in particular. The operating mechanisms that govern the relationship between composition and grain size are interpreted using a model originally developed for aluminum and magnesium alloys and subsequently applied for titanium alloys. The prior beta grain factor observed and the interpretations of their correlations indicate that tungsten is a good grain refiner and such models are valid to explain the grain-refinement process. By extension, other binary elements or higher order alloy systems with similar thermophysical properties should exhibit similar grain refinement.

Describing earthquakes potential through mountain building processes: an example within Nepal Himalaya

NASA Astrophysics Data System (ADS)

Zhang, Zhen; Zhang, Huai; Shi, Yaolin; Mary, Baptiste; Wang, Liangshu

2016-04-01

How to reconcile earthquake activities, for instance, the distributions of large-great event rupture areas and the partitioning of seismic-aseismic slips on the subduction interface, into geological mountain building period is critical in seismotectonics. In this paper, we try to scope this issue within a typical and special continental collisional mountain wedge within Himalayas across the 2015 Mw7.8 Nepal Himalaya earth- quake area. Based on the Critical Coulomb Wedge (CCW) theory, we show the possible predictions of large-great earthquake rupture locations by retrieving refined evolutionary sequences with clear boundary of coulomb wedge and creeping path inferred from interseismic deformation pattern along the megathrust-Main Himalaya Thrust (MHT). Due to the well-known thrusting architecture with constraints on the distribution of main exhumation zone and of the key evolutionary nodes, reasonable and refined (with 500 yr interval) thrusting sequences are retrieved by applying sequential limit analysis (SLA). We also use an illustration method-'G' gram to localize the relative positions of each fault within the tectonic wedge. Our model results show that at the early stage, during the initial wedge accumulation period, because of the small size of mountain wedge, there's no large earthquakes happens in this period. Whereas, in the following stage, the wedge is growing outward with occasionally out-of-sequence thrusting, four thrusting clusters (thrusting 'families') are clarified on the basis of the spatio-temporal distributions in the mountain wedge. Thrust family 4, located in the hinterland of the mountain wedge, absorbed the least amount of the total convergence, with no large earthquakes occurrence in this stage, contributing to the emplacement of the Greater Himalayan Complex. The slips absorbed by the remnant three thrust families result in large-great earthquakes rupturing in the Sub-Himalaya, Lesser Himalaya, and the front of Higher Himalaya. The portion rupturing in Sub-Himalaya is mainly great Himalaya earthquakes (M>8), with enough energy to rupture the whole MHT, while the thrusting family 2 and 3 will cause mainly large earthquakes. The averaged lifespan of single segment (inclined short lines) is growing from the deformation front to the hinterland, while the occurrence frequency is just in the opposite way. Thrusting slips in family 1-3 will enhance the coulomb wedge development resulting in mountain building. Note that, all the large earthquake behaviors described in this paper is a statistical characteristic, just the tendency distribution on the MHT in one interval. Although our research domain is a section of the Nepal Himalaya, the treatment proposed in this paper has universality in continental collisional orogenic belt which having the same interseismic pattern. We also summary the differences of seismogenic zones in oceanic subduction zone (Cascadia subduction zone) and arc-continental subduction zone (Taiwan area). The different types of interseismic pattern(mechanical patterns) are the controlling factors controlling seismic potential on megathrust and thus impacting the mountain building history.

40 CFR 80.230 - Who is not eligible for the hardship provisions for small refiners?

Code of Federal Regulations, 2011 CFR

2011-07-01

... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur... reorganization; (3) Importers; and (4) Refiners who produce gasoline other than by processing crude oil through... refineries for which the Administrator has approved an extension of the small refiner gasoline sulfur...

40 CFR 80.230 - Who is not eligible for the hardship provisions for small refiners?

Code of Federal Regulations, 2010 CFR

2010-07-01

... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Sulfur... reorganization; (3) Importers; and (4) Refiners who produce gasoline other than by processing crude oil through... refineries for which the Administrator has approved an extension of the small refiner gasoline sulfur...

Microstructural Characterization of Friction Stir Welded Aluminum-Steel Joints

NASA Astrophysics Data System (ADS)

Patterson, Erin E.; Hovanski, Yuri; Field, David P.

2016-06-01

This work focuses on the microstructural characterization of aluminum to steel friction stir welded joints. Lap weld configuration coupled with scribe technology used for the weld tool have produced joints of adequate quality, despite the significant differences in hardness and melting temperatures of the alloys. Common to friction stir processes, especially those of dissimilar alloys, are microstructural gradients including grain size, crystallographic texture, and precipitation of intermetallic compounds. Because of the significant influence that intermetallic compound formation has on mechanical and ballistic behavior, the characterization of the specific intermetallic phases and the degree to which they are formed in the weld microstructure is critical to predicting weld performance. This study used electron backscatter diffraction, energy dispersive spectroscopy, scanning electron microscopy, and Vickers micro-hardness indentation to explore and characterize the microstructures of lap friction stir welds between an applique 6061-T6 aluminum armor plate alloy and a RHA homogeneous armor plate steel alloy. Macroscopic defects such as micro-cracks were observed in the cross-sectional samples, and binary intermetallic compound layers were found to exist at the aluminum-steel interfaces of the steel particles stirred into the aluminum weld matrix and across the interfaces of the weld joints. Energy dispersive spectroscopy chemical analysis identified the intermetallic layer as monoclinic Al3Fe. Dramatic decreases in grain size in the thermo-mechanically affected zones and weld zones that evidenced grain refinement through plastic deformation and recrystallization. Crystallographic grain orientation and texture were examined using electron backscatter diffraction. Striated regions in the orientations of the aluminum alloy were determined to be the result of the severe deformation induced by the complex weld tool geometry. Many of the textures observed in the weld zone and thermo-mechanically affected zones exhibited shear texture components; however, there were many textures that deviated from ideal simple shear. Factors affecting the microstructure which are characteristic of the friction stir welding process, such as post-recrystallization deformation and complex deformation induced by tool geometry were discussed as causes for deviation from simple shear textures.

Adaptive Finite Element Methods for Continuum Damage Modeling

NASA Technical Reports Server (NTRS)

Min, J. B.; Tworzydlo, W. W.; Xiques, K. E.

1995-01-01

The paper presents an application of adaptive finite element methods to the modeling of low-cycle continuum damage and life prediction of high-temperature components. The major objective is to provide automated and accurate modeling of damaged zones through adaptive mesh refinement and adaptive time-stepping methods. The damage modeling methodology is implemented in an usual way by embedding damage evolution in the transient nonlinear solution of elasto-viscoplastic deformation problems. This nonlinear boundary-value problem is discretized by adaptive finite element methods. The automated h-adaptive mesh refinements are driven by error indicators, based on selected principal variables in the problem (stresses, non-elastic strains, damage, etc.). In the time domain, adaptive time-stepping is used, combined with a predictor-corrector time marching algorithm. The time selection is controlled by required time accuracy. In order to take into account strong temperature dependency of material parameters, the nonlinear structural solution a coupled with thermal analyses (one-way coupling). Several test examples illustrate the importance and benefits of adaptive mesh refinements in accurate prediction of damage levels and failure time.

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

40 CFR 409.31 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Liquid Cane Sugar Refining Subcategory § 409.31 Specialized... shall mean the addition of pollutants. (c) Melt shall mean that amount of raw material (raw sugar) contained within aqueous solution at the beginning of the process for production of refined cane sugar. ...

Large Engine Technology Program. Task 21: Rich Burn Liner for Near Term Experimental Evaluations

NASA Technical Reports Server (NTRS)

Hautman, D. J.; Padget, F. C.; Kwoka, D.; Siskind, K. S.; Lohmann, R. P.

2005-01-01

The objective of the task reported herein, which was conducted as part of the NASA sponsored Large Engine Technology program, was to define and evaluate a near-term rich-zone liner construction based on currently available materials and fabrication processes for a Rich-Quench-Lean combustor. This liner must be capable of operation at the temperatures and pressures of simulated HSCT flight conditions but only needs sufficient durability for limited duration testing in combustor rigs and demonstrator engines in the near future. This must be achieved at realistic cooling airflow rates since the approach must not compromise the emissions, performance, and operability of the test combustors, relative to the product engine goals. The effort was initiated with an analytical screening of three different liner construction concepts. These included a full cylinder metallic liner and one with multiple segments of monolithic ceramic, both of which incorporated convective cooling on the external surface using combustor airflow that bypassed the rich zone. The third approach was a metallic platelet construction with internal convective cooling. These three metal liner/jacket combinations were tested in a modified version of an existing Rich-Quench-Lean combustor rig to obtain data for heat transfer model refinement and durability verification.

Hydrochemical tracers in the middle Rio Grande Basin, USA: 1. Conceptualization of groundwater flow

USGS Publications Warehouse

Plummer, Niel; Bexfield, L.M.; Anderholm, S.K.; Sanford, W.E.; Busenberg, E.

2004-01-01

Chemical and isotopic data for groundwater from throughout the Middle Rio Grande Basin, central New Mexico, USA, were used to identify and map groundwater flow from 12 sources of water to the basin,evaluate radiocarbon ages, and refine the conceptual model of the Santa Fe Group aquifer system. Hydrochemical zones, representing groundwater flow over thousands to tens of thousands of years, can be traced over large distances through the primarily siliciclastic aquifer system. The locations of the hydrochemical zones mostly reflect the "modern" predevelopment hydraulic-head distribution, but are inconsistent with a trough in predevelopment water levels in the west-central part of the basin, indicating that this trough is a transient rather than a long-term feature of the aquifer system. Radiocarbon ages adjusted for geochemical reactions, mixing, and evapotranspiration/dilution processes in the aquifer system were nearly identical to the unadjusted radiocarbon ages, and ranged from modern to more than 30 ka. Age gradients from piezometer nests ranged from 0.1 to 2 year cm-1 and indicate a recharge rate of about 3 cm year-1 for recharge along the eastern mountain front and infiltration from the Rio Grande near Albuquerque. There has been appreciably less recharge along the eastern mountain front north and south of Albuquerque. ?? Springer-Verlag 2004.

Mantle structure and composition to 800-km depth beneath southern Africa and surrounding oceans from broadband body waves

NASA Astrophysics Data System (ADS)

Simon, R. E.; Wright, C.; Kwadiba, M. T. O.; Kgaswane, E. M.

2003-12-01

Average one-dimensional P and S wavespeed models from the surface to depths of 800 km were derived for the southern African region using travel times and waveforms from earthquakes recorded at stations of the Kaapvaal and South African seismic networks. The Herglotz-Wiechert method combined with ray tracing was used to derive a preliminary P wavespeed model, followed by refinements using phase-weighted stacking and synthetic seismograms to yield the final model. Travel times combined with ray tracing were used to derive the S wavespeed model, which was also refined using phase-weighted stacking and synthetic seismograms. The presence of a high wavespeed upper mantle lid in the S model overlying a low wavespeed zone (LWZ) around 210- to ˜345-km depth that is not observed in the P wavespeed model was inferred. The 410-km discontinuity shows similar characteristics to that in other continental regions, but occurs slightly deeper at 420 km. Depletion of iron and/or enrichment in aluminium relative to other regions are the preferred explanation, since the P wavespeeds throughout the transition zone are slightly higher than average. The average S wavespeed structure beneath southern Africa within and below the transition zone is similar to that of the IASP91 model. There is no evidence for discontinuity at 520-km depth. The 660-km discontinuity also appears to be slightly deeper than average (668 km), although the estimated thickness of the transition zone is 248 km, similar to the global average of 241 km. The small size of the 660-km discontinuity for P waves, compared with many other regions, suggests that interpretation of the discontinuity as the transformation of spinel to perovskite and magnesiowüstite may require modification. Alternative explanations include the presence of garnetite-rich material or ilmenite-forming phase transformations above the 660-km discontinuity, and the garnet-perovskite transformation as the discontinuity.

Improved ethanol yield and reduced minimum ethanol selling price (MESP) by modifying low severity dilute acid pretreatment with deacetylation and mechanical refining: 2) Techno-economic analysis

PubMed Central

2012-01-01

Background Our companion paper discussed the yield benefits achieved by integrating deacetylation, mechanical refining, and washing with low acid and low temperature pretreatment. To evaluate the impact of the modified process on the economic feasibility, a techno-economic analysis (TEA) was performed based on the experimental data presented in the companion paper. Results The cost benefits of dilute acid pretreatment technology combined with the process alternatives of deacetylation, mechanical refining, and pretreated solids washing were evaluated using cost benefit analysis within a conceptual modeling framework. Control cases were pretreated at much lower acid loadings and temperatures than used those in the NREL 2011 design case, resulting in much lower annual ethanol production. Therefore, the minimum ethanol selling prices (MESP) of the control cases were $0.41-$0.77 higher than the $2.15/gallon MESP of the design case. This increment is highly dependent on the carbohydrate content in the corn stover. However, if pretreatment was employed with either deacetylation or mechanical refining, the MESPs were reduced by $0.23-$0.30/gallon. Combing both steps could lower the MESP further by $0.44 ~ $0.54. Washing of the pretreated solids could also greatly improve the final ethanol yields. However, the large capital cost of the solid–liquid separation unit negatively influences the process economics. Finally, sensitivity analysis was performed to study the effect of the cost of the pretreatment reactor and the energy input for mechanical refining. A 50% cost reduction in the pretreatment reactor cost reduced the MESP of the entire conversion process by $0.11-$0.14/gallon, while a 10-fold increase in energy input for mechanical refining will increase the MESP by $0.07/gallon. Conclusion Deacetylation and mechanical refining process options combined with low acid, low severity pretreatments show improvements in ethanol yields and calculated MESP for cellulosic ethanol production. PMID:22967479

i3Drefine software for protein 3D structure refinement and its assessment in CASP10.

PubMed

Bhattacharya, Debswapna; Cheng, Jianlin

2013-01-01

Protein structure refinement refers to the process of improving the qualities of protein structures during structure modeling processes to bring them closer to their native states. Structure refinement has been drawing increasing attention in the community-wide Critical Assessment of techniques for Protein Structure prediction (CASP) experiments since its addition in 8(th) CASP experiment. During the 9(th) and recently concluded 10(th) CASP experiments, a consistent growth in number of refinement targets and participating groups has been witnessed. Yet, protein structure refinement still remains a largely unsolved problem with majority of participating groups in CASP refinement category failed to consistently improve the quality of structures issued for refinement. In order to alleviate this need, we developed a completely automated and computationally efficient protein 3D structure refinement method, i3Drefine, based on an iterative and highly convergent energy minimization algorithm with a powerful all-atom composite physics and knowledge-based force fields and hydrogen bonding (HB) network optimization technique. In the recent community-wide blind experiment, CASP10, i3Drefine (as 'MULTICOM-CONSTRUCT') was ranked as the best method in the server section as per the official assessment of CASP10 experiment. Here we provide the community with free access to i3Drefine software and systematically analyse the performance of i3Drefine in strict blind mode on the refinement targets issued in CASP10 refinement category and compare with other state-of-the-art refinement methods participating in CASP10. Our analysis demonstrates that i3Drefine is only fully-automated server participating in CASP10 exhibiting consistent improvement over the initial structures in both global and local structural quality metrics. Executable version of i3Drefine is freely available at http://protein.rnet.missouri.edu/i3drefine/.

Microstructural features of friction stir welded dissimilar Aluminium alloys AA2219-AA7475

NASA Astrophysics Data System (ADS)

Zaman Khan, Noor; Ubaid, Mohammed; Siddiquee, Arshad Noor; Khan, Zahid A.; Al-Ahmari, Abdulrahman; Chen, Xizhang; Haider Abidi, Mustufa

2018-05-01

High strength, good corrosion resistance, light weight make aluminium alloys a material of choice in many industrial sectors like aerospace, marine etc. Problems associated with welding of these alloys by fusion welding processes restricted their use in various industries. Friction stir welding (FSW), a clean solid-state joining process, easily overcomes various difficulties encountered during conventional fusion welding processes. In the present work, the effect of rotational speed (710 rpm, 900 rpm and 1120 rpm) on micro-hardness distribution and microstructure of FSWed dissimilar aluminium alloy joints were analyzed. Plates of AA7475-T761 and AA2219-O having thickness of 2.5 mm were welded by fixing AA7475 on retreating side (RS) and AA2219 on advancing side (AS). Welded joints were characterized by Vickers micro-hardness testing, scanning electron microscopy (SEM) and optical microscopy (OM). Results revealed that rotational speed significantly affects the micro-hardness due to increase in grain size, coarsening and dissolution of strengthening precipitates and re-precipitation. Higher micro-hardness values were observed in stir zone due to grain refinement and re-precipitation. Minimum micro-hardness value was observed at the TMAZ/HAZ of advancing side due to thermal softening.

Geophysical-geological studies of possible extensions of the New Madrid Fault Zone. Annual report, 1982. Vol. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinze, W.J.; Braile, L.W.; Keller, G.R.

1983-05-01

An integrated geophysical/geologic program is being conducted to evaluate the rift complex hypothesis as an explanation for the earthquake activity in the New Madrid Seismic Zone and its extensions, to refine our knowledge of the rift complex, and to investigate the possible northern extensions of the New Madrid Fault Zone, especially its possible connection to the Anna, Ohio seismogenic region. Drillhole basement lithologies are being investigated to aid in tectonic analysis and geophysical interpretation, particularly in the Anna, Ohio area. Gravity and magnetic modeling combined with limited seismic reflection studies in southwest Indiana are interpreted as confirming speculation that anmore » arm of the New Madrid Rift Complex extends northeasterly into Indiana. The geologic and geophysical evidence confirm that the basement lithology in the Anna, Ohio area is highly variable reflecting a complex geologic history. The data indicate that as many as three major Late Precambrian tectonic features intersect within the basement of the Anna area suggesting that the seismicity may be related to basement zones of weakness.« less

Enhanced service zone architecture for multiservices over IP

NASA Astrophysics Data System (ADS)

Michaely, Boaz; Mohan, Seshadri

2001-07-01

Recently, the field of IP Telephony has been experienced considerable evolution through the specification of new protocols and introduction of products implementing these protocols. We visualize IP Telephony evolving to soon offer multiservices encompassing not only voice, but also data, video and multimedia. While the progress has focused on refining protocols and architectures, very little attention has been given to business models for offering these services. This paper introduces the concept of a Service Zone, which from a service provider/network operator perspective fits within the operator's administrative domain, but is viewed as an independent zone with its own management and services, requiring minimal integration with the core network services. Besides its own management, the Enhanced Services Zone may also provide provisioning and maintenance features needed to provide the customer services and availability that subscribers expect from a telephony service providers. The platform must provide reliable service over time, be scalable to meet increased capacity demands, and be upgradeable to incorporate advanced services and features as they become available. Signaling flows are illustrated using SIP and H.323.

Hydrodynamic caracterisation of an heterogeneous aquifer system under semi-arid climate

NASA Astrophysics Data System (ADS)

Drias, T.; Toubal, A. Ch

2009-04-01

The studied zone is a part of the Mellegne's (North-East of Algeria) under pound, this zone is characterised by its semi-arid climate. The water bearing system is formed by the plio-quaternairy alluviums resting on a marley substratuim of age Eocene. The geostatiscitcs approach of the hydrodynamics parameters (Hydrolic load, transmisivity) allowed the study of their spatial distrubution (casting) by the method of Krigeage by blocks and the identification of zones with water-bearing potentialities. In this respect, the zone of Ain Chabro which, is situated in the South of the plain shows the best values of the transmisivity...... The use of a bidimensinnel model in the differences ended in the permanent regime allowed us to establish the global balence sheet (overall assessment) of the tablecloth and to refine the transmisivity field. These would vary more exactley between 10-4 to 10-2 m²/s. The method associating the probability appraoch of Krigeage to that determining the model has facilited the wedging of the model and clarified the inflitration value. Keys words: hydrodynamics, geostatiscitcs, Modeling, Chabro, Tébessa.

New insights on active fault geometries in the Mentawai region of Sumatra, Indonesia, from broadband waveform modeling of earthquake source parameters

NASA Astrophysics Data System (ADS)

WANG, X.; Wei, S.; Bradley, K. E.

2017-12-01

Global earthquake catalogs provide important first-order constraints on the geometries of active faults. However, the accuracies of both locations and focal mechanisms in these catalogs are typically insufficient to resolve detailed fault geometries. This issue is particularly critical in subduction zones, where most great earthquakes occur. The Slab 1.0 model (Hayes et al. 2012), which was derived from global earthquake catalogs, has smooth fault geometries, and cannot adequately address local structural complexities that are critical for understanding earthquake rupture patterns, coseismic slip distributions, and geodetically monitored interseismic coupling. In this study, we conduct careful relocation and waveform modeling of earthquake source parameters to reveal fault geometries in greater detail. We take advantage of global data and conduct broadband waveform modeling for medium size earthquakes (M>4.5) to refine their source parameters, which include locations and fault plane solutions. The refined source parameters can greatly improve the imaging of fault geometry (e.g., Wang et al., 2017). We apply these approaches to earthquakes recorded since 1990 in the Mentawai region offshore of central Sumatra. Our results indicate that the uncertainty of the horizontal location, depth and dip angle estimation are as small as 5 km, 2 km and 5 degrees, respectively. The refined catalog shows that the 2005 and 2009 "back-thrust" sequences in Mentawai region actually occurred on a steeply landward-dipping fault, contradicting previous studies that inferred a seaward-dipping backthrust. We interpret these earthquakes as `unsticking' of the Sumatran accretionary wedge along a backstop fault that separates accreted material of the wedge from the strong Sunda lithosphere, or reactivation of an old normal fault buried beneath the forearc basin. We also find that the seismicity on the Sunda megathrust deviates in location from Slab 1.0 by up to 7 km, with along strike variation. The refined megathrust geometry will improve our understanding of the tectonic setting in this region, and place further constraints on rupture processes of the hazardous megathrust.

Mercury and methylmercury dynamics in the hyporheic zone of an Oregon stream

USGS Publications Warehouse

Hinkle, Stephen R.; Bencala, Kenneth E.; Wentz, Dennis A.; Krabbenhoft, David P.

2014-01-01

The role of the hyporheic zone in mercury (Hg) cycling has received limited attention despite the biogeochemically active nature of this zone and, thus, its potential to influence Hg behavior in streams. An assessment of Hg geochemistry in the hyporheic zone of a coarse-grained island in the Coast Fork Willamette River in Oregon, USA, illustrates the spatially dynamic nature of this region of the stream channel for Hg mobilization and attenuation. Hyporheic flow through the island was evident from the water-table geometry and supported by hyporheic-zone chemistry distinct from that of the bounding groundwater system. Redox-indicator species changed abruptly along a transect through the hyporheic zone, indicating a biogeochemically reactive stream/hyporheic-zone continuum. Dissolved organic carbon (DOC), total Hg, and methylmercury (MeHg) concentrations increased in the upgradient portion of the hyporheic zone and decreased in the downgradient region. Total Hg (collected in 2002 and 2003) and MeHg (collected in 2003) were correlated with DOC in hyporheic-zone samples: r2=0.63 (total Hg-DOC, 2002), 0.73 (total Hg-DOC, 2003), and 0.94 (MeHg-DOC, 2003). Weaker Hg/DOC association in late summer 2002 than in early summer 2003 may reflect seasonal differences in DOC reactivity. Observed correlations between DOC and both total Hg and MeHg reflect the importance of DOC for Hg mobilization, transport, and fate in this hyporheic zone. Correlations with DOC provide a framework for conceptualizing and quantifying Hg and MeHg dynamics in this region of the stream channel, and provide a refined conceptual model of the role hyporheic zones may play in aquatic ecosystems.

Unlocking the Secrets of the Mantle Wedge: New Insights Into Melt Generation Processes in Subduction Zones

NASA Astrophysics Data System (ADS)

Grove, T. L.

2007-05-01

Recent laboratory studies of the melting and crystallization behavior of mantle peridotite and subduction zone lavas have led to new insights into melting processes in island arc settings. Melting of the mantle wedge in the presence of H2O begins at much lower temperatures than previously thought. The solidus of mantle peridotite at 3 GPa is ~ 800 °C, which is 200 °C below previous estimates. At pressures greater than 2.4 GPa chlorite becomes a stable phase on the solidus and it remains stable until ~ 3.5 GPa. Therefore, melting over this pressure range occurs in the presence of chlorite, which contains ~ 12 wt. % H2O. Chlorite stabilized on the peridotite solidus by slab-derived H2O may be the ultimate source of H2O for subduction zone magmatism. Thus, chlorite could transport large amounts of H2O into the descending mantle wedge to depths where it can participate in melting to generate hydrous arc magmas. Our ability to identify primitive mantle melts at subduction zones has led to the following observations. 1) Primitive mantle melts show evidence of final equilibration at shallow depths near the mantle - crust boundary. 2) They contain variable amounts of dissolved H2O (up to 6 wt. %). 3) They record variable extents of melting (up to > 25 wt. %). To produce melts with such variable characteristics requires more than one melting process and requires consideration of a new type of melting called hydrous flux melting. Flux melting occurs when the H2O - rich melt initially produced on the solidus near the base of the mantle wedge ascends and continuously reacts with overlying hotter, shallower mantle. The mantle melts and magmatic H2O content is constantly diluted as the melt ascends and reacts with shallower, hotter mantle. Anhydrous mantle melts are also found in close temporal and spatial proximity to hydrous flux melts. These melts are extracted at similar depths near the top of the mantle wedge when mantle is advected up and into the wedge corner and melted by adiabatic decompression. In light of these new insights into the chemical processes that lead to melt generation in subduction zones, further study of the influence of mantle dynamics and physical processes on melting is crucial. Variations in mantle permeability near the base of the wedge may exercise important controls on the access of fluids and/or melts to the overlying wedge. The presence of chlorite in the wedge may also influence rheological properties and seismicity in the vicinity of the slab - wedge interface. Improved knowledge of rheology and permeability will help us to develop more robust models of mantle flow and temperature distribution in the mantle wedge. These are crucial for refining melting models. By combining evidence from petrology, geochemistry and geophysics the mysteries that attend the generation of melt in the mantle wedge can be resolved.

Microstructure and Mechanical Properties of 316L Stainless Steel Filling Friction Stir-Welded Joints

NASA Astrophysics Data System (ADS)

Zhou, L.; Nakata, K.; Tsumura, T.; Fujii, H.; Ikeuchi, K.; Michishita, Y.; Fujiya, Y.; Morimoto, M.

2014-10-01

Keyhole left at 316L stainless steel friction stir welding/friction stir processing seam was repaired by filling friction stir welding (FFSW). Both metallurgical and mechanical bonding characteristics were obtained by the combined plastic deformation and flow between the consumable filling tool and the wall of the keyhole. Two ways based on the original conical and modified spherical keyholes, together with corresponding filling tools and process parameters were investigated. Microstructure and mechanical properties of 316L stainless steel FFSW joints were evaluated. The results showed that void defects existed at the bottom of the refilled original conical keyhole, while excellent bonding interface was obtained on the refilled modified spherical keyhole. The FFSW joint with defect-free interface obtained on the modified spherical keyhole fractured at the base metal side during the tensile test due to microstructural refinement and hardness increase in the refilled keyhole. Moreover, no σ phase but few Cr carbides were formed in the refilled zone, which would not result in obvious corrosion resistance degradation of 316L stainless steel.

Data indicating temperature response of Ti-6Al-4V thin-walled structure during its additive manufacture via Laser Engineered Net Shaping.

PubMed

Marshall, Garrett J; Thompson, Scott M; Shamsaei, Nima

2016-06-01

An OPTOMEC Laser Engineered Net Shaping (LENS(™)) 750 system was retrofitted with a melt pool pyrometer and in-chamber infrared (IR) camera for nondestructive thermal inspection of the blown-powder, direct laser deposition (DLD) process. Data indicative of temperature and heat transfer within the melt pool and heat affected zone atop a thin-walled structure of Ti-6Al-4V during its additive manufacture are provided. Melt pool temperature data were collected via the dual-wavelength pyrometer while the dynamic, bulk part temperature distribution was collected using the IR camera. Such data are provided in Comma Separated Values (CSV) file format, containing a 752×480 matrix and a 320×240 matrix of temperatures corresponding to individual pixels of the pyrometer and IR camera, respectively. The IR camera and pyrometer temperature data are provided in blackbody-calibrated, raw forms. Provided thermal data can aid in generating and refining process-property-performance relationships between laser manufacturing and its fabricated materials.

Data indicating temperature response of Ti–6Al–4V thin-walled structure during its additive manufacture via Laser Engineered Net Shaping

PubMed Central

Marshall, Garrett J.; Thompson, Scott M.; Shamsaei, Nima

2016-01-01

An OPTOMEC Laser Engineered Net Shaping (LENS™) 750 system was retrofitted with a melt pool pyrometer and in-chamber infrared (IR) camera for nondestructive thermal inspection of the blown-powder, direct laser deposition (DLD) process. Data indicative of temperature and heat transfer within the melt pool and heat affected zone atop a thin-walled structure of Ti–6Al–4V during its additive manufacture are provided. Melt pool temperature data were collected via the dual-wavelength pyrometer while the dynamic, bulk part temperature distribution was collected using the IR camera. Such data are provided in Comma Separated Values (CSV) file format, containing a 752×480 matrix and a 320×240 matrix of temperatures corresponding to individual pixels of the pyrometer and IR camera, respectively. The IR camera and pyrometer temperature data are provided in blackbody-calibrated, raw forms. Provided thermal data can aid in generating and refining process-property-performance relationships between laser manufacturing and its fabricated materials. PMID:27054180

Unidirectional self-assembly of soft templated mesoporous carbons by zone annealing

NASA Astrophysics Data System (ADS)

Xue, Jiachen; Singh, Gurpreet; Qiang, Zhe; Karim, Alamgir; Vogt, Bryan D.

2013-08-01

Surfactant or block copolymer-templated mesoporous films have been extensively explored, but achieving mesostructure coherence and unidirectional orientation over macroscopic dimensions has remained quite challenging for these self-assembled systems. Here, we extend the concepts associated with zone refinement of crystalline materials to soft templated mesoporous carbon films based on the cooperative assembly of commercial non-ionic surfactants (block copolymers) and phenolic resin oligomers (resol) to provide macroscopic alignment of both cubic (FDU-16) and hexagonal (FDU-15) mesostructures. The average orientation of these mesophases is determined from rotation grazing incidence small angle X-ray scattering (GISAXS) measurements. For FDU-15 templated by Pluronic P123, the orientation factor for the zone-annealed film is 0.98 based on the average of the second Legendre polynomial, but this orientation deteriorates significantly during carbonization. Notably, a thermal stabilization step following zone annealing preserves the orientation of the mesostructure during carbonization. The orientation factor for an isotropic cubic structure (FDU-16 templated by Pluronic F127) is only 0.48 (based on the 111 reflection with incident angle 0.15°) for the same zone annealing protocol, but this illustrates the versatility of zone annealing to different mesostructures. Unexpectedly, zone annealing of FDU-15 templated by Pluronic F127 leads to stabilization of the mesostructure through carbonization, whereas this structure collapses fully during carbonization even after extended oven annealing; despite no clear macroscopic orientation of the cylindrical mesostructure from zone annealing. Thermal zone annealing provides a simple methodology to produce highly ordered and macroscopically oriented stable mesoporous carbon films, but the efficacy is strongly tied to the mobility of the template during the zone annealing.Surfactant or block copolymer-templated mesoporous films have been extensively explored, but achieving mesostructure coherence and unidirectional orientation over macroscopic dimensions has remained quite challenging for these self-assembled systems. Here, we extend the concepts associated with zone refinement of crystalline materials to soft templated mesoporous carbon films based on the cooperative assembly of commercial non-ionic surfactants (block copolymers) and phenolic resin oligomers (resol) to provide macroscopic alignment of both cubic (FDU-16) and hexagonal (FDU-15) mesostructures. The average orientation of these mesophases is determined from rotation grazing incidence small angle X-ray scattering (GISAXS) measurements. For FDU-15 templated by Pluronic P123, the orientation factor for the zone-annealed film is 0.98 based on the average of the second Legendre polynomial, but this orientation deteriorates significantly during carbonization. Notably, a thermal stabilization step following zone annealing preserves the orientation of the mesostructure during carbonization. The orientation factor for an isotropic cubic structure (FDU-16 templated by Pluronic F127) is only 0.48 (based on the 111 reflection with incident angle 0.15°) for the same zone annealing protocol, but this illustrates the versatility of zone annealing to different mesostructures. Unexpectedly, zone annealing of FDU-15 templated by Pluronic F127 leads to stabilization of the mesostructure through carbonization, whereas this structure collapses fully during carbonization even after extended oven annealing; despite no clear macroscopic orientation of the cylindrical mesostructure from zone annealing. Thermal zone annealing provides a simple methodology to produce highly ordered and macroscopically oriented stable mesoporous carbon films, but the efficacy is strongly tied to the mobility of the template during the zone annealing. Electronic supplementary information (ESI) available: GISAXS profiles for the FDU-15-F127 at φ = 0° and φ = 90° is included along with 2D GISAXS data for all azimuthal data associated with FDU-15-P123 to illustrate the azimuthal dependence on the diffraction patterns. See DOI: 10.1039/c3nr02821f

Interacting Convective Processes in Kilauea Iki Lava Lake, Hawaii

NASA Astrophysics Data System (ADS)

Helz, R. T.

2007-12-01

Kilauea Iki lava lake formed in 1959 as a closed magma chamber of 40 million m3 of picritic magma. Repeated drilling and sampling of the lake allows recognition of processes of magmatic differentiation, and places time restrictions on the periods when they operated. Two processes, double-diffusive convection and finger diapirism, occurred because melt density decreases as olivine crystallization and re-equilibration proceeds, until after plagioclase begins to crystallize. Finger diapirism, described in previous work, occurred from 1961 to 1971 and affected most the lava lake between depths of 13 to 94 m. The period of inferred double- diffusive convection occurred between mid-1962 and 1964 and affected only the most olivine-poor part of the lava lake. Recent re-evaluation of petrographic and chemical data refine our understanding of this second process. The overall variation of bulk MgO content with depth in Kilauea Iki is an S-curve, consistent with gravitative redistribution of the abundant olivine phenocrysts present in the erupted lava. The olivine-poor zone (MgO <11 weight percent) is a sill-like volume found between depths of 21 to 43 m in the lake. This zone is bisected by a median layer containing more and slightly coarser olivine phenocrysts, which has an MgO content 2 weight percent higher than the minimum in the layers above and below. This configuration, not achievable by gravitative settling, suggests that the olivine-poor zone at some point contained a two-layer convective system. The upper and median layers of the olivine-poor zone contain a sparse population of augite microphenocrysts (0.2-0.4 mm in length), often in monomineralic clusters (1-3 mm in length), while the lower layer contains only olivine. Plagioclase and other phases occur only in the groundmass in all samples. If the layers developed before groundmass crystallization began, then the assemblage in the upper layer was olivine + augite, and was olivine-only in the lower. Because melt density decreases as temperature decreases in this part of the crystallization range and because the lava lake was strongly cooled from above, the conditions for double- diffusive convection, with splitting of the melt column into layers, were met. Core samples and temperature data obtained by drilling the lake in mid-1962 and late 1967 constrain the period of double-diffusive convection to the first half of that period. The process ceased without shifting the position of the median olivine-enriched layer downward, suggesting that it was very brief. Finger diapirism, already active in Kilauea Iki, was volumetrically more important, and passed through both layers. This overlapping process may have ended the broader convective process by reducing the thermal gradient that drove it. Although double- diffusive convection was a minor process in Kilauea Iki, it did occur in this closed magma system.

Properties of Base Stocks Obtained from Used Engine Oils by Acid/Clay Re-refining (Proprietes des Stocks de Base Obtenus par Regeneration des Huiles a Moteur Usees par le Procede de Traitement a l’Acide et a la Terre),

DTIC Science & Technology

1980-09-01

Research Conseil national Council Canada de recherches Canada LEY EL < PROPERTIES OF BASE STOCKS OBTAINED FROM USED ENGINE OILS BY ACID /CLAY RE-REFINING DTIC...MECHANICAL ENGINEERING REPORT Canad NC MP75 NRC NO. 18719 PROPERTIES OF BASE STOCKS OBTAINED FROM USED ENGINE OILS BY ACID /CLAY RE-REFINING (PROPRIETES...refined Base Stock ..................................... 10 3 Physical Test Data of Acid /Clay Process - Re-refined Base Stock Oils ............ 11 4

Helium stars: Towards an understanding of Wolf-Rayet evolution

NASA Astrophysics Data System (ADS)

McClelland, Liam A. S.; Eldridge, J. J.

2017-11-01

Recent observational modelling of the atmospheres of hydrogen-free Wolf-Rayet stars have indicated that their stellar surfaces are cooler than those predicted by the latest stellar evolution models. We have created a large grid of pure helium star models to investigate the dependence of the surface temperatures on factors such as the rate of mass loss and the amount of clumping in the outer convection zone. Upon comparing our results with Galactic and LMC WR observations, we find that the outer convection zones should be clumped and that the mass-loss rates need to be slightly reduced. We discuss the implications of these findings in terms of the detectability of Type Ibc supernovae progenitors, and in terms of refining the Conti scenario.

Instantaneous Coastline Extraction from LIDAR Point Cloud and High Resolution Remote Sensing Imagery

NASA Astrophysics Data System (ADS)

Li, Y.; Zhoing, L.; Lai, Z.; Gan, Z.

2018-04-01

A new method was proposed for instantaneous waterline extraction in this paper, which combines point cloud geometry features and image spectral characteristics of the coastal zone. The proposed method consists of follow steps: Mean Shift algorithm is used to segment the coastal zone of high resolution remote sensing images into small regions containing semantic information;Region features are extracted by integrating LiDAR data and the surface area of the image; initial waterlines are extracted by α-shape algorithm; a region growing algorithm with is taking into coastline refinement, with a growth rule integrating the intensity and topography of LiDAR data; moothing the coastline. Experiments are conducted to demonstrate the efficiency of the proposed method.

The VoiLA ocean bottom seismic array: First insights into the intermediate depth seismicity distribution in the Lesser Antilles

NASA Astrophysics Data System (ADS)

Rietbrock, A.; Harmon, N.; Goes, S. D. B.; Krueger, F.; Bie, L.; Collier, J.; Rychert, C.; Hicks, S. P.; Kendall, J. M.; Henstock, T.

2017-12-01

Subduction zones are the most important regions for the exchange of water between the Oceans and the solid Earth. Hydrated oceanic lithosphere is subducted into the deeper Earth and its bound water content is continuously released in a heterogeneous process as temperature and pressure rises with depth. As only small amounts of water can significantly alter the physical properties of materials at depth, water is believed to play a major role in the seismogenesis for both, the shallow megathrust responsible for large destructive earthquakes and the occurrence of Wadati-Benioff zone seismicity at intermediate depth. Up to now most of our observations have been made around the Circum-Pacific subduction were predominantly oceanic lithosphere generated at fast-spreading ridges is being subducted. Contrary, observations of dehydration processes occurring in subducting oceanic lithosphere generated at slow spreading ridges are limited. The Lesser Antilles subduction zone therefore provides the unique opportunity to study the linkage between seismicity and de-hydration reaction for subductiong lithosphere generated at a slow-spreading ridge. Between March 2016 and May 2017 34 Ocean Bottom Broadband Seismometers were deployed along the Lesser Antilles margin in the area 12°-18° N and 63.5°-59.5° W. The network consisted out of 24 DEPAS instruments with 120s Trillium compact sensors provided by the instrument pool of AWI (Germany) and 10 OBSIP instruments with Trillium 240s sensors provided by Scripps Institute of Oceanography (US). All instruments were recovered and only 2 OBSIP instruments did not collect any usable data. The remaining 32 instruments did record continuously all components and no clock timing issues were identified. Preliminary screening of the data shows a low noise level and numerous local/regional earthquakes with M<3 have been detected. We will present the recorded seismicity distribution and earthquake locations based on a refined 1D/2D velocity model.

Microstructural Evolution of Al-1Fe (Weight Percent) Alloy During Accumulative Continuous Extrusion Forming

NASA Astrophysics Data System (ADS)

Wang, Xiang; Guan, Ren-Guo; Tie, Di; Shang, Ying-Qiu; Jin, Hong-Mei; Li, Hong-Chao

2018-04-01

As a new microstructure refining method, accumulative continuous extrusion forming (ACEF) cannot only refine metal matrix but also refine the phases that exist in it. In order to detect the refinements of grain and second phase during the process, Al-1Fe (wt pct) alloy was processed by ACEF, and the microstructural evolution was analyzed by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Results revealed that the average grain size of Al-1Fe (wt pct) alloy decreased from 13 to 1.2 μm, and blocky Al3Fe phase with an average length of 300 nm was granulated to Al3Fe particle with an average diameter of 200 nm, after one pass of ACEF. Refinement of grain was attributed to continuous dynamic recrystallization (CDRX), and the granulation of Al3Fe phase included the spheroidization resulting from deformation heat and the fragmentation caused by the coupling effects of strain and thermal effect. The spheroidization worked in almost the entire deformation process, while the fragmentation required strain accumulation. However, fragmentation contributed more than spheroidization. Al3Fe particle stimulated the formation of substructure and retarded the migration of recrystallized grain boundary, but the effect of Al3Fe phase on refinement of grain could only be determined by the contrastive investigation of Al-1Fe (wt pct) alloy and pure Al.

76 FR 5107 - Regulation of Oil-Bearing Hazardous Secondary Materials From the Petroleum Refining Industry...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-28

... Processed in a Gasification System To Produce Synthesis Gas; Tentative Determination To Deny Petition for... Synthesis Gas,'' published in the Federal Register on January 2, 2008. The EPA considered the petition... Refining Industry Processed in a Gasification System to Produce Synthesis Gas'' (Gasification Rule). This...

Fiberboards from loblolly pine refiner groundwood: effects of gross wood characteristics and board density

Treesearch

Charles W. McMillin

1968-01-01

Boards for insulation and and structural uses are being manufactured in increasing quantities. The coarse fiber required for these products can be disk-refined from untreated wood chips. Since such fiber is produced in essentially one mechanical operation, continuous control is required of the raw material as well as the refining process.

Environmental Early Warning Systems (EEWS): Equation Writer’s Manual.

DTIC Science & Technology

1986-07-01

Flowchart 17 2-3 Preliminary Equation Form in Non-EEWS Format 20 2-4 Completed EEWS Form for a Coastal Zone Consideration 21 2-5 Data Ready to Be Loaded 24...Area into workable Subtopics. 4. Formulate flowcharts to separate and show interrelationships between Subtopic Areas and their desired outputs. 5...Army demand criteria (Army background). 9. Refine flowcharts for each specific Subtopic Area and estimate difficulty of accomplishing each step (Figure

A View of Cyberterrorism Five Years Later (PREPRINT)

DTIC Science & Technology

2007-01-01

2006, http://www.zone-h.org/content/view/10/30/, accessed June 12, 2006. 17 Stephen Ulph, “Internet Mujahideen Refine Electronic Warfare Tactics...Jeffrey Pool, “Technology and Security Discussions on the Jihadist Forums,” Jamestown Foundation, October 11, 2005. 26 Stephen Ulph, “Internet...Domination Design,” The Age, August 24, 2005. 36 Dan Verton, Black Ice, Mc- Graw Hill, 2003, pp. 88-91. 37 Susan Schmidt, “Qatari Man Designated

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Lehao

A nanocrystalline surface layer was produced on Mg-3 wt.% Li-6 wt.% Al alloy by means of surface mechanical attrition treatment (SMAT). Microstructure features of various sections were systematically characterized by transmission electron microscopy. The results indicate that grain refinement induced by SMAT is dominated mainly by dislocation slip. Twinning is active at the early stage of grain refinement process when the grain size is large. The dislocation-dominated deformation mechanism is attributed to the change of c/a ratio due to the alloying of Li in Mg matrix and the suppression of twinning due to grain refinement. Nanoindentation results show that themore » hardness of the surface is enhanced by SMAT. - Highlights: •Nanocrystalline surface layer was produced on Mg-3 wt.%Li-6 wt.%Al alloy by SMAT. •Grain refinement induced by SMAT is dominated mainly by dislocation slip. •Twinning is active at the early stage of grain refinement process. •The hardness of the surface was enhanced by SMAT.« less

TENORM: Bauxite and Alumina Production Wastes

EPA Pesticide Factsheets

Bauxite is used to produce alumina, which is then used to produce aluminum. Naturally-occurring radioactivity in bauxite ores is concentrated during the refining process, creating TENORM in bauxite refining residuals.

Microstructure and Porosity of Laser Welds in Cast Ti-6Al-4V with Addition of Boron

NASA Astrophysics Data System (ADS)

Tolvanen, Sakari; Pederson, Robert; Klement, Uta

2018-03-01

Addition of small amounts of boron to cast Ti-6Al-4V alloy has shown to render a finer microstructure and improved mechanical properties. For such an improved alloy to be widely applicable for large aerospace structural components, successful welding of such castings is essential. In the present work, the microstructure and porosity of laser welds in a standard grade cast Ti-6Al-4V alloy as well as two modified alloy versions with different boron concentrations have been investigated. Prior-β grain reconstruction revealed the prior-β grain structure in the weld zones. In fusion zones of the welds, boron was found to refine the grain size significantly and rendered narrow elongated grains. TiB particles in the prior-β grain boundaries in the cast base material restricted grain growth in the heat-affected zone. The TiB particles that existed in the as cast alloys decreased in size in the fusion zones of welds. The hardness in the weld zones was higher than in the base material and boron did not have a significant effect on hardness of the weld zones. The fusion zones were smaller in the boron-modified alloys as compared with Ti-6Al-4V without boron. Computed tomography X-ray investigations of the laser welds showed that pores in the FZ of the boron modified alloys were confined to the lower part of the welds, suggesting that boron addition influences melt pool flow.

Friction stir processing of an aluminum-magnesium alloy with pre-placing elemental titanium powder: In-situ formation of an Al{sub 3}Ti-reinforced nanocomposite and materials characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khodabakhshi, F., E-mail: farzadkhodabakhshi83@gmail.com; Simchi, A.; Institute for Nanoscience and Nanotechnology, Sharif University of Technology, P.O. Box 11365-9466, Azadi Avenue, 14588 Tehran

A fine-grained Al–Mg/Al{sub 3}Ti nanocomposite was fabricated by friction stir processing (FSP) of an aluminum-magnesium (AA5052) alloy with pre-placed titanium powder in the stirred zone. Microstructural evolutions and formation of intermetallic phases were analyzed by optical and electron microscopic techniques across the thickness section of the processed sheets. The microstructure of the nanocomposite consisted of a fine-grained aluminum matrix (1.5 µm), un-reacted titanium particles (<40 µm) and reinforcement particles of Al{sub 3}Ti (<100 nm) and Mg{sub 2}Si (<100 nm). Detailed microstructural analysis indicated solid-state interfacial reactions between the aluminum matrix and micro-sized titanium particles to form Al{sub 3}Ti intermetallic phase.more » The hard inclusions were then fractured and re-distributed in the metal matrix by the severe thermo-mechanical conditions imposed by FSP. Evaluation of mechanical properties by hardness measurement and uniaxial tensile test determined significant enhancement in the mechanical strength (by 2.5 order of magnetite) with a high ductility (~22%). Based on a dislocation-based model analysis, it was suggested that the strength enhancement was governed by grain refinement and the presence of hard inclusions (4 vol%) in the metal matrix. Fractographic studies also showed a ductile-brittle fracture mode for the nanocomposite compared with fully ductile rupture of the annealed alloy as well as the FSPed specimen without pre-placing titanium particles. - Highlights: • FSP was employed to fabricate in situ nanocomposite. • The AA5052 Al alloy with pre-placed micro-sized Ti particles were utilized. • The structural analysis was revealed that the in situ formation of Al{sub 3}Ti nanophase. • The SZ grain structure was refined by PSN and ZHP mechanisms during DRX. • Hardness and tensile strength were improved up to ~2.5 times with a good ductility.« less

Depth of the vadose zone controls aquifer biogeochemical conditions and extent of anthropogenic nitrogen removal

USGS Publications Warehouse

Szymczycha, Beata; Kroeger, Kevin D.; Crusius, John; Bratton, John F.

2017-01-01

We investigated biogeochemical conditions and watershed features controlling the extent of nitrate removal through microbial dinitrogen (N2) production within the surficial glacial aquifer located on the north and south shores of Long Island, NY, USA. The extent of N2 production differs within portions of the aquifer, with greatest N2 production observed at the south shore of Long Island where the vadose zone is thinnest, while limited N2production occurred under the thick vadose zones on the north shore. In areas with a shallow water table and thin vadose zone, low oxygen concentrations and sufficient DOC concentrations are conducive to N2production. Results support the hypothesis that in aquifers without a significant supply of sediment-bound reducing potential, vadose zone thickness exerts an important control of the extent of N2 production. Since quantification of excess N2 relies on knowledge of equilibrium N2concentration at recharge, calculated based on temperature at recharge, we further identify several features, such as land use and cover, seasonality of recharge, and climate change that should be considered to refine estimation of recharge temperature, its deviation from mean annual air temperature, and resulting deviation from expected equilibrium gas concentrations.

Design Ideas, Reflection, and Professional Identity: How Graduate Students Explore the Idea Generation Process

ERIC Educational Resources Information Center

Hutchinson, Alisa; Tracey, Monica W.

2015-01-01

Within design thinking, designers are responsible for generating, testing, and refining design ideas as a means to refine the design problem and arrive at an effective solution. Thus, understanding one's individual idea generation experiences and processes can be seen as a component of professional identity for designers, which involves the…

Initial Assessment of U.S. Refineries for Purposes of Potential Bio-Based Oil Insertions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freeman, Charles J.; Jones, Susanne B.; Padmaperuma, Asanga B.

2013-04-01

In order to meet U.S. biofuel objectives over the coming decade the conversion of a broad range of biomass feedstocks, using diverse processing options, will be required. Further, the production of both gasoline and diesel biofuels will employ biomass conversion methods that produce wide boiling range intermediate oils requiring treatment similar to conventional refining processes (i.e. fluid catalytic cracking, hydrocracking, and hydrotreating). As such, it is widely recognized that leveraging existing U.S. petroleum refining infrastructure is key to reducing overall capital demands. This study examines how existing U.S. refining location, capacities and conversion capabilities match in geography and processing capabilitiesmore » with the needs projected from anticipated biofuels production.« less

Investigation on Microstructure and Mechanical Properties of Continuous and Pulsed Current Gas Tungsten Arc Welded alloy 600

NASA Astrophysics Data System (ADS)

Srikanth, A.; Manikandan, M.

2018-02-01

The present study investigates the microstructure and mechanical properties of joints fabricated by Continuous and pulsed current gas tungsten arc welded alloy 600. Welding was done by autogenous mode. The macro examination was carried out to evaluate the welding defects in the weld joints. Optical and Scanning Electron Microscope (SEM) were performed to assess the microstructural changes in the fusion zone. Energy Dispersive Spectroscopy (EDS) analysis was carried to evaluate the microsegregation of alloying elements in the fusion zone. The tensile test was conducted to assess the strength of the weld joints. The results show that no welding defects were observed in the fusion zones of Continuous and Pulsed current Gas Tungsten Arc Welding. The refined microstructure was found in the pulsed current compared to continuous current mode. Microsegregation was not noticed in the weld grain boundary of continuous and pulsed current mode. The pulsed current shows improved mechanical properties compared to the continuous current mode.

Self-adjusted flux for the traveling solvent floating zone growth of YBaCuFeO5 crystal

NASA Astrophysics Data System (ADS)

Lai, Yen-Chung; Shu, Guo-Jiun; Chen, Wei-Tin; Du, Chao-Hung; Chou, Fang-Cheng

2015-03-01

A modified traveling solvent floating zone (TSFZ) technique was used to successfully grow a large size and high quality single crystal of multiferroic material YBaCuFeO5. This modified TSFZ growth uses a stoichiometric feed rod and pure copper oxide as the initial flux without prior knowledge of the complex phase diagram involving four elements, and the optimal flux for the growth of incongruently melt crystal is self-adjusted after a prolonged stable pulling. The wetting of the feed rod edge that often perturbs the molten zone stability was avoided by adding 2 wt% B2O3. The optimal flux concentration for the YBaCuFeO5 growth can be extracted to be near YBaCuFeO5:CuO=13:87 in molar ratio. The crystal quality was confirmed by the satisfactory refinement of crystal structure of space group P4mm and the two consecutive anisotropic antiferromagnetic phase transitions near 455 K and 170 K.

Reducing PEC uncertainty in coastal zones: a case study on carbamazepine, oxcarbazepine and their metabolites.

PubMed

Fenet, Hélène; Arpin-Pont, Lauren; Vanhoutte-Brunier, Alice; Munaron, Dominique; Fiandrino, Annie; Martínez Bueno, Maria-Jesus; Boillot, Clotilde; Casellas, Claude; Mathieu, Olivier; Gomez, Elena

2014-07-01

Concentrations of the antiepileptic drugs carbamazepine (Cbz), oxcarbazepine (OxCz) and their main metabolites were predicted in a wastewater treatment plant (WTP) and in the vicinity of its submarine outfall located in a Mediterranean coastal zone. Refined predicted environmental concentrations (PECs) were calculated in effluents based on consumption data and human excretion rates. PECs were estimated in the sea using the hydrodynamic MARS 3D model integrating meteorological data, oceanic conditions (wind, tide, atmospheric pressure), freshwater and sewage inputs. Measured environmental concentrations (MECs) were compared to PECs to assess the estimation relevance. In the coastal zone, PEC and MEC were in the same magnitude range. Modeling of Cbz diffusion and advection just above the submarine outfall showed the influence of the thermocline during summer, with low diffusion of Cbz from the bottom to the surface. This work allowed understanding the dispersion of target compounds and deserved further development for a better acknowledgement of vulnerability at local scales. Copyright © 2014 Elsevier Ltd. All rights reserved.

Corrosion Performance of Friction Stir Linear Lap Welded AM60B Joints

NASA Astrophysics Data System (ADS)

Kish, J. R.; Birbilis, N.; McNally, E. M.; Glover, C. F.; Zhang, X.; McDermid, J. R.; Williams, G.

2017-11-01

A corrosion investigation of friction stir linear lap welded AM60B joints used to fabricate an Mg alloy-intensive automotive front end sub-assembly was performed. The stir zone exhibited a slightly refined grain size and significant break-up and re-distribution of the divorced Mg17Al12 (β-phase) relative to the base material. Exposures in NaCl (aq) environments revealed that the stir zone was more susceptible to localized corrosion than the base material. Scanning vibrating electrode technique measurements revealed differential galvanic activity across the joint. Anodic activity was confined to the stir zone surface and involved initiation and lateral propagation of localized filaments. Cathodic activity was initially confined to the base material surface, but was rapidly modified to include the cathodically-activated corrosion products in the filament wake. Site-specific surface analyses revealed that the corrosion observed across the welded joint was likely linked to variations in Al distribution across the surface film/metal interface.

Polycrystalline silicon study: Low-cost silicon refining technology prospects and semiconductor-grade polycrystalline silicon availability through 1988

NASA Technical Reports Server (NTRS)

Costogue, E. N.; Ferber, R.; Lutwack, R.; Lorenz, J. H.; Pellin, R.

1984-01-01

Photovoltaic arrays that convert solar energy into electrical energy can become a cost effective bulk energy generation alternative, provided that an adequate supply of low cost materials is available. One of the key requirements for economic photovoltaic cells is reasonably priced silicon. At present, the photovoltaic industry is dependent upon polycrystalline silicon refined by the Siemens process primarily for integrated circuits, power devices, and discrete semiconductor devices. This dependency is expected to continue until the DOE sponsored low cost silicon refining technology developments have matured to the point where they are in commercial use. The photovoltaic industry can then develop its own source of supply. Silicon material availability and market pricing projections through 1988 are updated based on data collected early in 1984. The silicon refining industry plans to meet the increasing demands of the semiconductor device and photovoltaic product industries are overviewed. In addition, the DOE sponsored technology research for producing low cost polycrystalline silicon, probabilistic cost analysis for the two most promising production processes for achieving the DOE cost goals, and the impacts of the DOE photovoltaics program silicon refining research upon the commercial polycrystalline silicon refining industry are addressed.

i3Drefine Software for Protein 3D Structure Refinement and Its Assessment in CASP10

PubMed Central

Bhattacharya, Debswapna; Cheng, Jianlin

2013-01-01

Protein structure refinement refers to the process of improving the qualities of protein structures during structure modeling processes to bring them closer to their native states. Structure refinement has been drawing increasing attention in the community-wide Critical Assessment of techniques for Protein Structure prediction (CASP) experiments since its addition in 8th CASP experiment. During the 9th and recently concluded 10th CASP experiments, a consistent growth in number of refinement targets and participating groups has been witnessed. Yet, protein structure refinement still remains a largely unsolved problem with majority of participating groups in CASP refinement category failed to consistently improve the quality of structures issued for refinement. In order to alleviate this need, we developed a completely automated and computationally efficient protein 3D structure refinement method, i3Drefine, based on an iterative and highly convergent energy minimization algorithm with a powerful all-atom composite physics and knowledge-based force fields and hydrogen bonding (HB) network optimization technique. In the recent community-wide blind experiment, CASP10, i3Drefine (as ‘MULTICOM-CONSTRUCT’) was ranked as the best method in the server section as per the official assessment of CASP10 experiment. Here we provide the community with free access to i3Drefine software and systematically analyse the performance of i3Drefine in strict blind mode on the refinement targets issued in CASP10 refinement category and compare with other state-of-the-art refinement methods participating in CASP10. Our analysis demonstrates that i3Drefine is only fully-automated server participating in CASP10 exhibiting consistent improvement over the initial structures in both global and local structural quality metrics. Executable version of i3Drefine is freely available at http://protein.rnet.missouri.edu/i3drefine/. PMID:23894517

An Environmentally Friendly Process Involving Refining and Membrane-Based Electrolysis for Magnesium Recovery from Partially Oxidized Scrap Alloy

NASA Astrophysics Data System (ADS)

Guan, Xiaofei; Pal, Uday B.; Powell, Adam C.

2013-10-01

Magnesium is recovered from partially oxidized scrap alloy by combining refining and solid oxide membrane (SOM) electrolysis. In this combined process, a molten salt eutectic flux (45 wt.% MgF2-55 wt.% CaF2) containing 10 wt.% MgO and 2 wt.% YF3 was used as the medium for magnesium recovery. During refining, magnesium and its oxide are dissolved from the scrap into the molten flux. Forming gas is bubbled through the flux and the dissolved magnesium is removed via the gas phase and condensed in a separate condenser at a lower temperature. The molten flux has a finite solubility for magnesium and acts as a selective medium for magnesium dissolution, but not aluminum or iron, and therefore the magnesium recovered has high purity. After refining, SOM electrolysis is performed in the same reactor to enable electrolysis of the dissolved magnesium oxide in the molten flux producing magnesium at the cathode and oxygen at the SOM anode. During SOM electrolysis, it is necessary to decrease the concentration of the dissolved magnesium in the flux to improve the faradaic current efficiency and prevent degradation of the SOM. Thus, for both refining and SOM electrolysis, it is very important to measure and control the magnesium solubility in the molten flux. High magnesium solubility facilitates refining whereas lower solubility benefits the SOM electrolysis process. Computational fluid dynamics modeling was employed to simulate the flow behavior of the flux stirred by the forming gas. Based on the modeling results, an optimized design of the stirring tubes and its placement in the flux are determined for efficiently removing the dissolved magnesium and also increasing the efficiency of the SOM electrolysis process.

Continuous steel production and apparatus

DOEpatents

Peaslee, Kent D [Rolla, MO; Peter, Jorg J [McMinnville, OR; Robertson, David G. C. [Rolla, MO; Thomas, Brian G [Champaign, IL; Zhang, Lifeng [Trondheim, NO

2009-11-17

A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

Protective Effects of Fetal Zone Steroids Are Comparable to Estradiol in Hyperoxia-Induced Cell Death of Immature Glia.

PubMed

Hübner, Stephanie; Sunny, Donna E; Pöhlke, Christine; Ruhnau, Johanna; Vogelgesang, Antje; Reich, Bettina; Heckmann, Matthias

2017-05-01

Impaired neurodevelopment in preterm infants is caused by prematurity itself; however, hypoxia/ischemia, inflammation, and hyperoxia contribute to the extent of impairment. Because preterm birth is accompanied by a dramatic decrease in 17β-estradiol (E2) and progesterone, preliminary clinical studies have been carried out to substitute these steroids in preterm infants; however, they failed to confirm significantly improved neurologic outcomes. We therefore hypothesized that the persistently high postnatal production of fetal zone steroids [mainly dehydroepiandrosterone (DHEA)] until term could interfere with E2-mediated protection. We investigated whether E2 could reduce hyperoxia-mediated apoptosis in three immature glial cell types and detected the involved receptors. Thereafter, we investigated protection by the fetal zone steroids DHEA, 16α-hydroxy-DHEA, and androstenediol. For DHEA, the involved receptors were evaluated. We examined aromatases, which convert fetal zone steroids into more estrogenic compounds. Finally, cotreatment was compared against single hormone treatment to investigate synergism. In all cell types, E2 and fetal zone steroids resulted in significant dose-dependent protection, whereas the mediating receptors differed. The neuroprotection by fetal zone steroids highly depended on the cell type-specific expression of aromatases, the receptor repertoire, and the potency of the fetal zone steroids toward these receptors. No synergism in fetal zone steroid and E2 cotreatment was detected in two of three cell types. Therefore, E2 supplementation may not be beneficial with respect to neuroprotection because fetal zone steroids circulate in persistently high concentrations until term in preterm infants. Hence, a refined experimental model for preterm infants is required to investigate potential treatments. Copyright © 2017 Endocrine Society.

Bauxite mining and alumina refining: process description and occupational health risks.

PubMed

Donoghue, A Michael; Frisch, Neale; Olney, David

2014-05-01

To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Review article. The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures.

Intermediate-Scale Investigation of Capillary and Dissolution Trapping during CO2 Injection and Post-Injection in Heterogeneous Geological Formations

NASA Astrophysics Data System (ADS)

Cihan, A.; Illangasekare, T. H.; Zhou, Q.; Birkholzer, J. T.; Rodriguez, D.

2010-12-01

The capillary and dissolution trapping processes are believed to be major trapping mechanisms during CO2 injection and post-injection in heterogeneous subsurface environments. These processes are important at relatively shorter time periods compared to mineralization and have a strong impact on storage capacity and leakage risks, and they are suitable to investigate at reasonable times in the laboratory. The objectives of the research presented is to investigate the effect of the texture transitions and variability in heterogeneous field formations on the effective capillary and dissolution trapping at the field scale through multistage analysis comprising of experimental and modeling studies. A series of controlled experiments in intermediate-scale test tanks are proposed to investigate the key processes involving (1) viscous fingering of free-phase CO2 along high-permeability (or high-K) fast flow pathways, (2) dynamic intrusion of CO2 from high-K zones into low-K zones by capillarity (as well as buoyancy), (3) diffusive transport of dissolved CO2 into low-K zones across large interface areas, and (4) density-driven convective mass transfer into CO2-free regions. The test tanks contain liquid sampling ports to measure spatial and temporal changes in concentration of dissolved fluid as the injected fluid migrates. In addition to visualization and capturing images through digital photography, X-ray and gamma attenuation methods are used to measure phase saturations. Heterogeneous packing configurations are created with tightly packed sands ranging from very fine to medium fine to mimic sedimentary rocks at potential storage formations. Effect of formation type, injection pressure and injection rate on trapped fluid fraction are quantified. Macroscopic variables such as saturation, pressure and concentration that are measured will be used for testing the existing macroscopic models. The applicability of multiphase flow theories will be evaluated by comparing with the experimental data. Existing upscaling methodologies will be tested using experimental data for accurately estimating parameters of the large-scale heterogeneous porous media. This paper presents preliminary results from the initial-stage experiments and the modeling analysis. In the future, we will design and conduct a comprehensive set of experiments for improving the fundamental understanding of the processes, and refine and calibrate the models simulating the effective capillary and dissolution trapping with an ultimate goal to design efficient and safe storage schemes.

On the microstructure analysis of FSW joints of aluminium components made via direct metal laser sintering

NASA Astrophysics Data System (ADS)

Scherillo, Fabio; Astarita, Antonello; di Martino, Daniela; Contaldi, Vincenzo; di Matteo, Luca; di Petta, Paolo; Casarin, Renzo; Squillace, Antonino; Langella, Antonio

2017-10-01

Additive Manufacturing (AM), applied to metal industry, is a family of processes that allow complex shape components to be realized from raw materials in the form of powders. The compaction of the powders can be achieved by local melting of the powder bed or by solid state sintering. Direct Metal Laser Sintering (DMLS) is an additive manufacturing process in which a focalized laser beam is the heat source that allows the powders to be compacted. By DMLS it is possible to realize complex shape components. One of the limits of DMLS, as for every additive layer manufacturing techniques, is the unfeasibility to realize large dimension parts. Due to this limit the study of joining process of parts made via ALM is of great interest. One of the most promising options is the Friction Stir Welding (FSW), a solid state welding technique that has been proven to be very effective in the welding of metals difficult to weld, above all aluminium alloys. Since FSW is a solid-state technique, the microstructure of the various zone of the weld bead depends not only by the process itself but also by the parent microstruct ure of the parts to be welded. Furthermore, parts made of aluminium alloy via DMLS have a particular microstructure that is the result of repeated severe thermal cycles. In the present work the authors, starting from the description of the parent microstructure of parts made of AlSi10Mg aluminium alloy, study the microstructure evolution occurred within the joint made by Friction Stir Welding, analysing in details the microstructure of the main well recognized zone of the weld bead. The structure of the parent material is characterized by the presence of melting pools with a very fine microstructure. In the joint the recrystallization, the grain refinement and, above all, the redistribution of intermetallic phases occurs, resulting in an homogenization of the microstructure and in an increase of micro hardness.

Effect of Deformation Parameters on Microstructure and Properties During DIFT of X70HD Pipeline Steel

NASA Astrophysics Data System (ADS)

Wang, Jian; Zhu, Wei; Xiao, Hong; Zhang, Liang-liang; Qin, Hao; Yu, Yue

2018-02-01

Grain refinement is a critical approach to improve the strength of materials without damaging the toughness. The grains of deformation-induced ferrite are considerably smaller than those of proeutectoid ferrite. Grain refinement is crucial to the application of deformation-induced ferrite. The composition of ferrite and bainite or martensite is important in controlling the performance of X70HD pipeline steel, and cooling significantly influences the control of their ratio and grain size. By analyzing the static and dynamic phase-transition points using Gleeble-3800 thermal simulator, thermal simulations were performed through two-stage deformations in the austenite zone. Ferrite transformation rules were studied with thermal simulation tests under different deformation and cooling parameters based on the actual production of cumulative deformation. The influence of deformation parameters on the microstructure transformation was analyzed. Numerous fine-grain deformation-induced ferrites were obtained by regulating various parameters, including deformation temperature, strain rate, cooling rate, final cooling temperature and other parameters. Results of metallographic observation and microtensile testing revealed that the selection of appropriate parameters can refine the grains and improve the performance of the X70HD pipeline steel.

Pharmacophore Refinement Guides the Design of Nanomolar-Range Botulinum Neurotoxin Serotype A Light Chain Inhibitors

PubMed Central

2010-01-01

Botulinum neurotoxins (BoNTs) are the deadliest of microbial toxins. The enzymes’ zinc(II) metalloprotease, referred to as the light chain (LC) component, inhibits acetylcholine release into neuromuscular junctions, resulting in the disease botulism. Currently, no therapies counter BoNT poisoning postneuronal intoxication; however, it is hypothesized that small molecules may be used to inhibit BoNT LC activity in the neuronal cytosol. Herein, we describe the pharmacophore-based design and chemical synthesis of potent [non-zinc(II) chelating] small molecule (nonpeptidic) inhibitors (SMNPIs) of the BoNT serotype A LC (the most toxic of the BoNT serotype LCs). Specifically, the three-dimensional superimpositions of 2-[4-(4-amidinephenoxy)phenyl]indole-6-amidine-based SMNPI regioisomers [Ki = 0.600 μM (±0.100 μM)], with a novel lead bis-[3-amide-5-(imidazolino)phenyl]terephthalamide (BAIPT)-based SMNPI [Ki = 8.52 μM (±0.53 μM)], resulted in a refined four-zone pharmacophore. The refined model guided the design of BAIPT-based SMNPIs possessing Ki values = 0.572 (±0.041 μM) and 0.900 μM (±0.078 μM). PMID:21116458

Ice Floe Breaking in Contemporary Third Generation Operational Wave Models

NASA Astrophysics Data System (ADS)

Sévigny, C.; Baudry, J.; Gauthier, J. C.; Dumont, D.

2016-02-01

The dynamical zone observed at the edge of the consolidated ice area where are found the wave-fractured floes (i.e. marginal ice zone or MIZ) has become an important topic in ocean modeling. As both operational and climate ocean models now seek to reproduce the complex atmosphere-ice-ocean system with realistic coupling processes, many theoretical and numerical studies have focused on understanding and modeling this zone. Few attempts have been made to embed wave-ice interactions specific to the MIZ within a two-dimensional model, giving the possibility to calculate both the attenuation of surface waves by sea ice and the concomitant breaking of the sea ice-cover into smaller floes. One of the first challenges consists in improving the parameterization of wave-ice dynamics in contemporary third generation operational wave models. A simple waves-in-ice model (WIM) similar to the one proposed by Williams et al. (2013a,b) was implemented in WAVEWATCH III. This WIM considers ice floes as floating elastic plates and predicts the dimensionless attenuation coefficient by the use of a lookup-table-based, wave scattering scheme. As in Dumont et al. (2011), the different frequencies are treated individually and floe breaking occurs for a particular frequency when the expected wave amplitude exceeds the allowed strain amplitude, which considers ice floes properties and wavelength in ice field. The model is here further refined and tested in idealized two-dimensional cases, giving preliminary results of the performance and sensitivity of the parameterization to initial wave and ice conditions. The effects of the wave-ice coupling over the incident wave spectrum are analyzed as well as the resulting floe size distribution. The model gives prognostic values of the lateral extent of the marginal ice zone with maximum ice floe diameter that progressively increases with distance from the ice edge.

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

NASA Technical Reports Server (NTRS)

Lewis, J. C.; Kenny, J. T.

1976-01-01

Sustained load crack growth data for Ti-6Al-4V titanium alloy in hydrazine per MIL-P-26536 and refined hydrazine are presented. Fracture mechanics data on crack growth thresholds for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones are reported. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are generated from 40 to 71 C.

Three-dimensional superconducting gap in FeSe from angle-resolved photoemission spectroscopy

NASA Astrophysics Data System (ADS)

Kushnirenko, Y. S.; Fedorov, A. V.; Haubold, E.; Thirupathaiah, S.; Wolf, T.; Aswartham, S.; Morozov, I.; Kim, T. K.; Büchner, B.; Borisenko, S. V.

2018-05-01

We present a systematic angle-resolved photoemission spectroscopy study of the superconducting gap in FeSe. The gap function is determined in a full Brillouin zone including all Fermi surfaces and kz dependence. We find significant anisotropy of the superconducting gap in all momentum directions. While the in-plane anisotropy can be explained by both nematicity-induced pairing anisotropy and orbital-selective pairing, the kz anisotropy requires an additional refinement of the theoretical approaches.

Middle East oil and gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-12-01

The following subjects are covered in this publication: (1) position of preeminence of the Middle East; (2) history of area's oil operations for Iran, Iraq, Bahrain, Kuwait, Saudi Arabia, neutral zone, Qatar, United Arab Emirates, Oman and Egypt; (3) gas operations of Saudi Arabia, Iran, Kuwait, Qatar, Iraq and United Arab Emirates; (4) changing relationships with producing countries; (5) a new oil pricing environment; (6) refining and other industrial activities; and (7) change and progress. 10 figs., 12 tabs.

Refinement of Regional Distance Seismic Moment Tensor and Uncertainty Analysis for Source-Type Identification

DTIC Science & Technology

2014-09-02

release; distribution is unlimited. rock zone which provides a pathway for formation fluids, natural gas and crude oil from deeper strata that are... southeast Louisiana (Figure 21). It is a part of the Gulf Coast salt basin which exhibits many salt structures formed by upward flow of sedimentary salt...primarily, evaporites) on account of low density of salt and overburden pressures caused by younger sedimentary deposits (Beckman and Williamson, 1990

Refinement of late-Early and Middle Miocene diatom biostratigraphy for the east coast of the United States

USGS Publications Warehouse

Barron, John A.; Browning, James; Sugarman, Peter; Miller, Kenneth G.

2013-01-01

Integrated Ocean Drilling Program (IODP) Expedition 313 continuously cored Lower to Middle Miocene sequences at three continental shelf sites off New Jersey, USA. The most seaward of these, Site M29, contains a well-preserved Early and Middle Miocene succession of planktonic diatoms that have been independently correlated with the geomagnetic polarity time scale derived in studies from the equatorial and North Pacific. Shallow water diatoms (species of Delphineis, Rhaphoneis, and Sceptroneis) dominate in onshore sequences in Maryland and Virginia, forming the basis for the East Coast Diatom Zones (ECDZ). Integrated study of both planktonic and shallow water diatoms in Hole M29A as well as in onshore sequences in Maryland (the Baltimore Gas and Electric Company well) and Delaware (the Ocean Drilling Program Bethany Beach corehole) allows the refinement of ECDZ zones into a high-resolution biochronology that can be successfully applied in both onshore and offshore regions of the East Coast of the United States. Strontium isotope stratigraphy supports the diatom biochronology, although for much of the Middle Miocene it suggests ages that are on average 0.4 m.y. older. The ECDZ zonal definitions are updated to include evolutionary events of Delphineis species, and regional occurrences of important planktonic diatom marker taxa are included. Updated taxonomy, reference to published figures, and photographic images are provided that will aid in the application of this diatom biostratigraphy.

Sulfide-associated mineral assemblages in the Bushveld Complex, South Africa: platinum-group element enrichment by vapor refining by chloride-carbonate fluids

NASA Astrophysics Data System (ADS)

Kanitpanyacharoen, W.; Boudreau, A. E.

2013-02-01

The petrology of base metal sulfides and associated accessory minerals in rocks away from economically significant ore zones such as the Merensky Reef of the Bushveld Complex has previously received only scant attention, yet this information is critical in the evaluation of models for the formation of Bushveld-type platinum-group element (PGE) deposits. Trace sulfide minerals, primarily pyrite, pyrrhotite, pentlandite, and chalcopyrite are generally less than 100 microns in size, and occur as disseminated interstitial individual grains, as polyphase assemblages, and less commonly as inclusions in pyroxene, plagioclase, and olivine. Pyrite after pyrrhotite is commonly associated with low temperature greenschist alteration haloes around sulfide grains. Pyrrhotite hosted by Cr- and Ti-poor magnetite (Fe3O4) occurs in several samples from the Marginal to Lower Critical Zones below the platiniferous Merensky Reef. These grains occur with calcite that is in textural equilibrium with the igneous silicate minerals, occur with Cl-rich apatite, and are interpreted as resulting from high temperature sulfur loss during degassing of interstitial liquid. A quantitative model demonstrates how many of the first-order features of the Bushveld ore metal distribution could have developed by vapor refining of the crystal pile by chloride-carbonate-rich fluids during which sulfur and sulfide are continuously recycled, with sulfur moving from the interior of the crystal pile to the top during vapor degassing.

Refining of metallurgical-grade silicon

NASA Technical Reports Server (NTRS)

Dietl, J.

1986-01-01

A basic requirement of large scale solar cell fabrication is to provide low cost base material. Unconventional refining of metallurical grade silicon represents one of the most promising ways of silicon meltstock processing. The refining concept is based on an optimized combination of metallurgical treatments. Commercially available crude silicon, in this sequence, requires a first pyrometallurgical step by slagging, or, alternatively, solvent extraction by aluminum. After grinding and leaching, high purity qualtiy is gained as an advanced stage of refinement. To reach solar grade quality a final pyrometallurgical step is needed: liquid-gas extraction.

Microstructural characteristics of adiabatic shear localization in a metastable beta titanium alloy deformed at high strain rate and elevated temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhan, Hongyi, E-mail: h.zhan@uq.edu.au; Zeng, Weidong; Wang, Gui

2015-04-15

The microstructural evolution and grain refinement within adiabatic shear bands in the Ti6554 alloy deformed at high strain rates and elevated temperatures have been characterized using transmission electron microscopy. No stress drops were observed in the corresponding stress–strain curve, indicating that the initiation of adiabatic shear bands does not lead to the loss of load capacity for the Ti6554 alloy. The outer region of the shear bands mainly consists of cell structures bounded by dislocation clusters. Equiaxed subgrains in the core area of the shear band can be evolved from the subdivision of cell structures or reconstruction and transverse segmentationmore » of dislocation clusters. It is proposed that dislocation activity dominates the grain refinement process. The rotational recrystallization mechanism may operate as the kinetic requirements for it are fulfilled. The coexistence of different substructures across the shear bands implies that the microstructural evolution inside the shear bands is not homogeneous and different grain refinement mechanisms may operate simultaneously to refine the structure. - Graphical abstract: Display Omitted - Highlights: • The microstructure within the adiabatic shear band was characterized by TEM. • No stress drops were observed in the corresponding stress–strain curve. • Dislocation activity dominated the grain refinement process. • The kinetic requirements for rotational recrystallization mechanism were fulfilled. • Different grain refinement mechanisms operated simultaneously to refine the structure.« less

Initiating technical refinements in high-level golfers: Evidence for contradictory procedures.

PubMed

Carson, Howie J; Collins, Dave; Richards, Jim

2016-01-01

When developing motor skills there are several outcomes available to an athlete depending on their skill status and needs. Whereas the skill acquisition and performance literature is abundant, an under-researched outcome relates to the refinement of already acquired and well-established skills. Contrary to current recommendations for athletes to employ an external focus of attention and a representative practice design,  Carson and  Collins' (2011) [Refining and regaining skills in fixation/diversification stage performers: The Five-A Model. International Review of Sport and Exercise Psychology, 4, 146-167. doi: 10.1080/1750984x.2011.613682 ] Five-A Model requires an initial narrowed internal focus on the technical aspect needing refinement: the implication being that environments which limit external sources of information would be beneficial to achieving this task. Therefore, the purpose of this paper was to (1) provide a literature-based explanation for why techniques counter to current recommendations may be (temporarily) appropriate within the skill refinement process and (2) provide empirical evidence for such efficacy. Kinematic data and self-perception reports are provided from high-level golfers attempting to consciously initiate technical refinements while executing shots onto a driving range and into a close proximity net (i.e. with limited knowledge of results). It was hypothesised that greater control over intended refinements would occur when environmental stimuli were reduced in the most unrepresentative practice condition (i.e. hitting into a net). Results confirmed this, as evidenced by reduced intra-individual movement variability for all participants' individual refinements, despite little or no difference in mental effort reported. This research offers coaches guidance when working with performers who may find conscious recall difficult during the skill refinement process.

Production and characterization of refined oils obtained from Indian oil sardine (Sardinella longiceps).

PubMed

Chakraborty, Kajal; Joseph, Deepu

2015-01-28

Crude Sardinella longiceps oil was refined in different stages such as degumming, neutralization, bleaching, and deodorization. The efficiency of these processes was evaluated on the basis of free fatty acid (FFA), peroxide (PV), p-anisidine (pAV), total oxidation (TOTOX), thiobarbituric acid reactive species (TBARS) values, Lovibond CIE-L*a*b* color analyses, and (1)H NMR or GC-MS experiments. The utilities of NMR-based proton signal characteristics as new analytical tools to understand the signature peaks and relative abundance of different fatty acids and monitoring the refining process of fish oil have been demonstrated. Phosphoric acid (1%) was found to be an effective degumming reagent to obtain oil with the lowest FFA, PV, pAV, TOTOX, and TBARS values and highest color reduction. Significant reduction in the contents of hydrocarbon functionalities as shown by the decrease in proton integral in the characteristic (1)H NMR region was demonstrated by using 1% H3PO4 during the course of the degumming process. A combination (1.25:3.75%) of activated charcoal and Fuller's earth at 3% concentration for a stirring time of 40 min was found to be effective in bleaching the sardine oil. This study demonstrated that unfavorable odor-causing components, particularly low molecular weight carbonyl compounds, could successfully be removed by the refining process. The alkane-dienals/alkanes, which cause unfavorable fishy odors, were successfully removed by distillation (100 °C) under vacuum with aqueous acetic acid solution (0.25 N) to obtain greater quality of refined sardine oil, a rich source of essential fatty acids and improved oxidative stability. The present study demonstrated that the four-stage refinement process of sardine oil resulted in a significant improvement in quality characteristics and nutritional values, particularly n-3 PUFAs, with improved fish oil characteristics for use in the pharmaceutical and functional food industries.

Analysis of stress-strain state of support ring of vertical steel tank RVS-20000

NASA Astrophysics Data System (ADS)

Chepur, P. V.; Tarasenko, A. A.; Gruchenkova, A. A.

2018-05-01

The refined finite element model of the joint of a fixed roof with a support ring for a large-size vertical steel tank RVS-20000 is executed. It considers the real geometry of metal shell plates - in accordance with the TP-704-1-60 design, geometric and physical nonlinearity, and features of the non-axisymmetric design loading scheme of the structure. Dependences of the SSS parameters of the support joint design on the size of the subsidence zone of the outer contour of the RVS-20000 bottom are obtained. It is established that at the value of subsidence zone coefficient n ≤ 1, a region of critical values occurs, exceeding which leads to the appearance of unacceptable plastic deformations of metal structures. The authors performed interpretation of the postprocessing of the finite element analysis, as a result of which the dependences of the parameters of the stress-strain state on the value of the zone of warping were obtained. The graphs of the dependence of the values of strains and stresses of the metal structure of the support ring on the size of the subsidence zone along the arc of the outer contour of the bottom are presented.

Analysis of traffic congestion induced by the work zone

NASA Astrophysics Data System (ADS)

Fei, L.; Zhu, H. B.; Han, X. L.

2016-05-01

Based on the cellular automata model, a meticulous two-lane cellular automata model is proposed, in which the driving behavior difference and the difference of vehicles' accelerations between the moving state and the starting state are taken into account. Furthermore the vehicles' motion is refined by using the small cell of one meter long. Then accompanied by coming up with a traffic management measure, a two-lane highway traffic model containing a work zone is presented, in which the road is divided into normal area, merging area and work zone. The vehicles in different areas move forward according to different lane changing rules and position updating rules. After simulation it is found that when the density is small the cluster length in front of the work zone increases with the decrease of the merging probability. Then the suitable merging length and the appropriate speed limit value are recommended. The simulation result in the form of the speed-flow diagram is in good agreement with the empirical data. It indicates that the presented model is efficient and can partially reflect the real traffic. The results may be meaningful for traffic optimization and road construction management.

Three-dimensional elliptic grid generation for an F-16

NASA Technical Reports Server (NTRS)

Sorenson, Reese L.

1988-01-01

A case history depicting the effort to generate a computational grid for the simulation of transonic flow about an F-16 aircraft at realistic flight conditions is presented. The flow solver for which this grid is designed is a zonal one, using the Reynolds averaged Navier-Stokes equations near the surface of the aircraft, and the Euler equations in regions removed from the aircraft. A body conforming global grid, suitable for the Euler equation, is first generated using 3-D Poisson equations having inhomogeneous terms modeled after the 2-D GRAPE code. Regions of the global grid are then designated for zonal refinement as appropriate to accurately model the flow physics. Grid spacing suitable for solution of the Navier-Stokes equations is generated in the refinement zones by simple subdivision of the given coarse grid intervals. That grid generation project is described, with particular emphasis on the global coarse grid.

Air impacts from three alternatives for producing JP-8 jet fuel.

PubMed

Kositkanawuth, Ketwalee; Gangupomu, Roja Haritha; Sattler, Melanie L; Dennis, Brian H; MacDonnell, Frederick M; Billo, Richard; Priest, John W

2012-10-01

To increase U.S. petroleum energy independence, the University of Texas at Arlington (UT Arlington) has developed a direct coal liquefaction process which uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This sweet crude can be refined to form JP-8 military jet fuel, as well as other end products like gasoline and diesel. This paper presents an analysis of air pollutants resulting from using UT Arlington's liquefaction process to produce crude and then JP-8, compared with 2 alternative processes: conventional crude extraction and refining (CCER), and the Fischer-Tropsch process. For each of the 3 processes, air pollutant emissions through production of JP-8 fuel were considered, including emissions from upstream extraction/ production, transportation, and conversion/refining. Air pollutants from the direct liquefaction process were measured using a LandTEC GEM2000 Plus, Draeger color detector tubes, OhioLumex RA-915 Light Hg Analyzer, and SRI 8610 gas chromatograph with thermal conductivity detector. According to the screening analysis presented here, producing jet fuel from UT Arlington crude results in lower levels of pollutants compared to international conventional crude extraction/refining. Compared to US domestic CCER, the UTA process emits lower levels of CO2-e, NO(x), and Hg, and higher levels of CO and SO2. Emissions from the UT Arlington process for producing JP-8 are estimated to be lower than for the Fischer-Tropsch process for all pollutants, with the exception of CO2-e, which were high for the UT Arlington process due to nitrous oxide emissions from crude refining. When comparing emissions from conventional lignite combustion to produce electricity, versus UT Arlington coal liquefaction to make JP-8 and subsequent JP-8 transport, emissions from the UT Arlington process are estimated to be lower for all air pollutants, per MJ of power delivered to the end user. The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. At current use rates, U.S. coal reserves (262 billion short tons, including 23 billion short tons lignite) would last 236 years. Accordingly, the University of Texas at Arlington (UT Arlington) has developed a process that converts lignite to crude oil, at about half the cost of regular crude. According to the screening analysis presented here, producing jet fuel from UT Arlington crude generates lower levels of pollutants compared to international conventional crude extraction/refining (CCER).

ADAPTIVE TETRAHEDRAL GRID REFINEMENT AND COARSENING IN MESSAGE-PASSING ENVIRONMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hallberg, J.; Stagg, A.

2000-10-01

A grid refinement and coarsening scheme has been developed for tetrahedral and triangular grid-based calculations in message-passing environments. The element adaption scheme is based on an edge bisection of elements marked for refinement by an appropriate error indicator. Hash-table/linked-list data structures are used to store nodal and element formation. The grid along inter-processor boundaries is refined and coarsened consistently with the update of these data structures via MPI calls. The parallel adaption scheme has been applied to the solution of a transient, three-dimensional, nonlinear, groundwater flow problem. Timings indicate efficiency of the grid refinement process relative to the flow solvermore » calculations.« less

Effects of Processing and Powder Size on Microstructure and Reactivity in Arrested Reactive Milled Al + Ni

DTIC Science & Technology

2012-05-01

reactive milled (RM) experiments forming nickel aluminides [3,4,6,8–10,12,15,16,18,19], titanium - based alloys [5] and combustion reactions in metal...highly heterogeneous and is refined during processing until reaction occurs. The refinement process consists of the cold welding of powder grains within... welding at the surface of deforming particles, which pro-Table 2 Sample preparation measurements corresponding to the designed exper- iments presented

Using supercritical fluids to refine hydrocarbons

DOEpatents

Yarbro, Stephen Lee

2014-11-25

This is a method to reactively refine hydrocarbons, such as heavy oils with API gravities of less than 20.degree. and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure using a selected fluid at supercritical conditions. The reaction portion of the method delivers lighter weight, more volatile hydrocarbons to an attached contacting device that operates in mixed subcritical or supercritical modes. This separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques. This method produces valuable products with fewer processing steps, lower costs, increased worker safety due to less processing and handling, allow greater opportunity for new oil field development and subsequent positive economic impact, reduce related carbon dioxide, and wastes typical with conventional refineries.

Upgrading and Refining of Crude Oils and Petroleum Products by Ionizing Irradiation.

PubMed

Zaikin, Yuriy A; Zaikina, Raissa F

2016-06-01

A general trend in the oil industry is a decrease in the proven reserves of light crude oils so that any increase in future oil exploration is associated with high-viscous sulfuric oils and bitumen. Although the world reserves of heavy oil are much greater than those of sweet light oils, their exploration at present is less than 12 % of the total oil recovery. One of the main constraints is very high expenses for the existing technologies of heavy oil recovery, upgrading, transportation, and refining. Heavy oil processing by conventional methods is difficult and requires high power inputs and capital investments. Effective and economic processing of high viscous oil and oil residues needs not only improvements of the existing methods, such as thermal, catalytic and hydro-cracking, but the development of new technological approaches for upgrading and refining of any type of problem oil feedstock. One of the perspective approaches to this problem is the application of ionizing irradiation for high-viscous oil processing. Radiation methods for upgrading and refining high-viscous crude oils and petroleum products in a wide temperature range, oil desulfurization, radiation technology for refining used oil products, and a perspective method for gasoline radiation isomerization are discussed in this paper. The advantages of radiation technology are simple configuration of radiation facilities, low capital and operational costs, processing at lowered temperatures and nearly atmospheric pressure without the use of any catalysts, high production rates, relatively low energy consumption, and flexibility to the type of oil feedstock.

Effect of friction stir welding on microstructure and corrosion behavior of LF6 aluminum alloy

NASA Astrophysics Data System (ADS)

Ghauri, Faizan Ali; Farooq, A.; Ahmad, A.; Deen, K. M.

2017-03-01

The LF6 aluminum alloy plates were joined by friction stir welding method. The tool rotational (1180 rpm) and transverse speed (0.56 mm s-1) were kept constant during welding of 4 mm thick plates. The microstructural features, hardness and tensile properties of the welded samples were determined to evaluate the structural integrity in comparison with the base metal. The electrochemical behavior of base metal (BM), thermo-mechanically affected zone (TMAZ) and weld nugget zone (WNZ) was also investigated by potentiodynamic polarization and electrochemical impedance spectroscopy in 3.5% NaCl solution. The microstructural study revealed significant grain refinement and agglomeration of β (Mg2Al3) intermetallic precipitates in the WNZ. The relatively higher hardness and a decrease in the ductility (3%) also assured the formation of precipitates β precipitates in the WNZ welded samples. The fracture surface of welded sample also revealed the existence of β precipitates within the elongated dimples which may be considered as the crack initiation sites. The relatively lower corrosion rate (23.68 mpy) and higher charge transfer resistance (403 Ω cm2) of BM compared to WNZ could be associated with the galvanic dissolution of Al-matrix through competitive charge transfer and relaxation (adsorption/desorption of intermediate species) processes specifically at the vicinity of the β precipitates.

Origins and exploration significance of replacement and vein-type alunite deposits in the Marysvale volcanic field, west central Utah.

USGS Publications Warehouse

Cunningham, C.G.; Rye, R.O.; Steven, T.A.; Mehnert, H.H.

1984-01-01

Alunite in the Marysvale volcanic field forms two (three are described) different types of deposits which contrast in appearance and conditions of origin: 1) Replacement deposits are generally fine-grained and formed by near-surface replacement of intermediate-composition volcanic rocks. The deposits form a bead necklace around a monzonite stock. Each deposit is zoned horizontally from alunitic cores to kaolinitic and propylitic envelopes and zoned vertically from pyrite/propylite upward through alunite/jarosite/hematite to a silica cap. Alunite does not extend below 100 m. Sulphur isotope ratios agree with derivation from underlying Mesozoic evaporites. 2) Natroalunite of 14-m.y. age crosscuts replacement-type alunite deposits. Its S-isotope ratios are comparable with those of pyrite in the volcanics. The Na may be from underlying Mesozoic halites. 3) Veins of coarse-grained alunite of 14-m.y. age filled extension fractures above a postulated stock. S-isotope ratios indicate a probable magmatic source. The contrasting properties of the Marysvale alunite deposits preclude any simple relation to ore deposits, but serve to refine interpretations based on other geological considerations. The replacement deposits are a logical near-surface result of skarn forming processes at depth around the monzonite stock. The vein- type deposits are a logical near-surface result of porphyry metallization in an underlying stock. -G.J.N.

GPR as a Low Impact Paleontogical Survey Technique

NASA Astrophysics Data System (ADS)

Sturdevant, G. C.; Leverence, R.; Stewart, R.

2013-12-01

The Deweyville Formation, a Pleistocene fluvial sandstone, is a prolific source of megafaunal fossils from periods of low stand environmental conditions. GPR was employed in an environmentally sensitive area in close proximity to a salt dome in Northwest Harris County, Texas as a method of evaluating the probable paleo-depositional environment and to prospect for potential further site development of two distinct fossiliferous zones. The primary zone of interest is a lag gravel bounded sand responsible for producing a regionally unique fossil assemblage including South American megafauna (Lundelius et al, 2013). The secondary zone of interest contains undisturbed mammoth remains housed in coarse white sand emplaced on top of a clay drape which has been hypothesized to represent an oxbow lake formed by the meandering paleo-Brazos river. With an accurate map of the paleo-channel planning future activity can focus on maximizing fossil recovery and minimizing site impact. Pulse EKKO 250 MHz, 400MHz, and 1GHz system was employed in a prospect area proximal to the secondary site to calibrate and evaluate these systems for their resolution and penetration depth in the modern sediments. The data was processed using EKKO Mapper and EKKO View Deluxe software packages, 3d volumes were produced and sliced. Preliminary results from the 250 MHz demonstrate successful imaging of the sand-clay interface. After these surveys were run a small portion of the site was excavated to confirm the estimated velocities, the observed anomalies, and refine our modeling and interpretation, and improve grid design for further surveys. It was confirmed that the sand-clay interface was easily observable using GPR, however the grid spacing proved to be too wide, leading to artifacts in the 3d volume produced.

[Efficiency evaluation of capsaicinoids to discriminate bio-waste oils from edible vegetable oils].

PubMed

Mao, Lisha; Liu, Honghe; Kang, Li; Jiang, Jie; Liao, Shicheng; Liu, Guihua; Deng, Pingjian

2014-07-01

To evaluate the efficiency of capsaicinoids to discriminate bio-waste oil from edible vegetable oil. 14 raw vegetable oils, 24 fried waste oils, 34 kitchen-waste oils, 32 edible non-peanut vegetable oil, 32 edible peanuts oil, 16 edible oil add flavorand and 11 refined bio-waste oils were prepared and examined for capsaicinoids including capsaicin, dihydrocapsaicin and nonylic acid vanillylamide. The detection results of the above samples were statistically tested based on sample category to assessment identify the effectiveness of the bio-waste oils with capsaicinoids. As a indicator, capsaincin was possessed of high detection sensitivity and has the highest efficiency to discern kitchen-waste oils and refined bio-waste oils samples from edible non-peanut vegetable oil correctly. The accuracy rate of identification were 100% and 90.1% respectively. There is the background in peanut oil. CONCLUSION Capsaicin added in cooking process can be retained in the refining process and hardly be removed in the refining process. In the case of fully eliminating the background interference, capsaicinoids can effectively identify bio-waste oils and edible vegetable oil in combination.

Kinetics of Sub-Micron Grain Size Refinement in 9310 Steel

NASA Astrophysics Data System (ADS)

Kozmel, Thomas; Chen, Edward Y.; Chen, Charlie C.; Tin, Sammy

2014-05-01

Recent efforts have focused on the development of novel manufacturing processes capable of producing microstructures dominated by sub-micron grains. For structural applications, grain refinement has been shown to enhance mechanical properties such as strength, fatigue resistance, and fracture toughness. Through control of the thermo-mechanical processing parameters, dynamic recrystallization mechanisms were used to produce microstructures consisting of sub-micron grains in 9310 steel. Starting with initial bainitic grain sizes of 40 to 50 μm, various levels of grain refinement were observed following hot deformation of 9310 steel samples at temperatures and strain rates ranging from 755 K to 922 K (482 °C and 649 °C) and 1 to 0.001/s, respectively. The resulting deformation microstructures were characterized using scanning electron microscopy and electron backscatter diffraction techniques to quantify the extent of carbide coarsening and grain refinement occurring during deformation. Microstructural models based on the Zener-Holloman parameter were developed and modified to include the effect of the ferrite/carbide interactions within the system. These models were shown to effectively correlate microstructural attributes to the thermal mechanical processing parameters.

Chemical Processing of Non-Crop Plants for Jet Fuel Blends Production

NASA Technical Reports Server (NTRS)

Kulis, M. J.; Hepp, A. F.; McDowell, M.; Ribita, D.

2009-01-01

The use of Biofuels has been gaining in popularity over the past few years due to their ability to reduce the dependence on fossil fuels. Biofuels as a renewable energy source can be a viable option for sustaining long-term energy needs if they are managed efficiently. We describe our initial efforts to exploit algae, halophytes and other non-crop plants to produce synthetics for fuel blends that can potentially be used as fuels for aviation and non-aerospace applications. Our efforts have been dedicated to crafting efficient extraction and refining processes in order to extract constituents from the plant materials with the ultimate goal of determining the feasibility of producing biomass-based jet fuel from the refined extract. Two extraction methods have been developed based on communition processes, and liquid-solid extraction techniques. Refining procedures such as chlorophyll removal and transesterification of triglycerides have been performed. Gas chromatography in tandem with mass spectroscopy is currently being utilized in order to qualitatively determine the individual components of the refined extract. We also briefly discuss and compare alternative methods to extract fuel-blending agents from alternative biofuels sources.

Crystallization in lactose refining-a review.

PubMed

Wong, Shin Yee; Hartel, Richard W

2014-03-01

In the dairy industry, crystallization is an important separation process used in the refining of lactose from whey solutions. In the refining operation, lactose crystals are separated from the whey solution through nucleation, growth, and/or aggregation. The rate of crystallization is determined by the combined effect of crystallizer design, processing parameters, and impurities on the kinetics of the process. This review summarizes studies on lactose crystallization, including the mechanism, theory of crystallization, and the impact of various factors affecting the crystallization kinetics. In addition, an overview of the industrial crystallization operation highlights the problems faced by the lactose manufacturer. The approaches that are beneficial to the lactose manufacturer for process optimization or improvement are summarized in this review. Over the years, much knowledge has been acquired through extensive research. However, the industrial crystallization process is still far from optimized. Therefore, future effort should focus on transferring the new knowledge and technology to the dairy industry. © 2014 Institute of Food Technologists®

Using remotely piloted aircraft and onboard processing to optimize and expand data collection

NASA Astrophysics Data System (ADS)

Fladeland, M. M.; Sullivan, D. V.; Chirayath, V.; Instrella, R.; Phelps, G. A.

2016-12-01

Remotely piloted aircraft (RPA) have the potential to revolutionize local to regional data collection for geophysicists as platform and payload size decrease while aircraft capabilities increase. In particular, data from RPAs combine high-resolution imagery available from low flight elevations with comprehensive areal coverage, unattainable from ground investigations and difficult to acquire from manned aircraft due to budgetary and logistical costs. Low flight elevations are particularly important for detecting signals that decay exponentially with distance, such as electromagnetic fields. Onboard data processing coupled with high-bandwidth telemetry open up opportunities for real-time and near real-time data processing, producing more efficient flight plans through the use of payload-directed flight, machine learning and autonomous systems. Such applications not only strive to enhance data collection, but also enable novel sensing modalities and temporal resolution. NASA's Airborne Science Program has been refining the capabilities and applications of RPA in support of satellite calibration and data product validation for several decades. In this paper, we describe current platforms, payloads, and onboard data systems available to the research community. Case studies include Fluid Lensing for littoral zone 3D mapping, structure from motion for terrestrial 3D multispectral imaging, and airborne magnetometry on medium and small RPAs.

A PFI mill can be used to predict biomechanical pulp strength properties

Treesearch

Gary F. Leatham; Gary C. Myers

1990-01-01

Recently, we showed that a biomechanical pulping process in which aspen chips are pretreated with a white-rot fungus can give energy savings and can increase paper sheet strength. To optimize this process, we need more efficient ways to evaluate the fungal treatments. Here, we examine a method that consists of treating coarse refiner mechanical pulp, refining in a PFI...

Process for electroslag refining of uranium and uranium alloys

DOEpatents

Lewis, P.S. Jr.; Agee, W.A.; Bullock, J.S. IV; Condon, J.B.

1975-07-22

A process is described for electroslag refining of uranium and uranium alloys wherein molten uranium and uranium alloys are melted in a molten layer of a fluoride slag containing up to about 8 weight percent calcium metal. The calcium metal reduces oxides in the uranium and uranium alloys to provide them with an oxygen content of less than 100 parts per million. (auth)

40Ar/39Ar geochronology of submarine Mauna Loa volcano, Hawaii

NASA Astrophysics Data System (ADS)

Jicha, Brian R.; Rhodes, J. Michael; Singer, Brad S.; Garcia, Michael O.

2012-09-01

New geochronologic constraints refine the growth history of Mauna Loa volcano and enhance interpretations of the petrologic, geochemical, and isotopic evolution of Hawaiian magmatism. We report results of 40Ar/39Ar incremental heating experiments on low-K, tholeiitic lavas from the 1.6 km high Kahuku landslide scarp cutting Mauna Loa's submarine southwest rift zone, and from lavas in a deeper section of the rift. Obtaining precise40Ar/39Ar ages from young, tholeiitic lavas containing only 0.2-0.3 wt.% K2O is challenging due to their extremely low radiogenic 40Ar contents. Analyses of groundmass from 45 lavas yield 14 new age determinations (31% success rate) with plateau and isochron ages that agree with stratigraphic constraints. Lavas collected from a 1250 m thick section in the landslide scarp headwall were all erupted around 470 ± 10 ka, implying an extraordinary period of accumulation of ˜25 mm/yr, possibly correlating with the peak of the shield-building stage. This rate is three times higher than the estimated vertical lava accumulation rate for shield-building at Mauna Kea (8.6 ± 3.1 mm/yr) based on results from the Hawaii Scientific Drilling Project. Between ˜470 and 273 ka, the lava accumulation rate along the southwest rift zone decreased dramatically to ˜1 mm/yr. We propose that the marked reduction in lava accumulation rate does not mark the onset of post-shield volcanism as previously suggested, but rather indicates the upward migration of the magma system as Mauna Loa evolved from a submarine stage of growth to one that is predominantly subaerial, thereby cutting off supply to the distal rift zone. Prior to ˜250 ka, lavas with Loihi-like isotopic signatures were erupted along with lavas having typical Mauna Loa values, implying greater heterogeneity in the plume source earlier in Mauna Loa's growth. In addition to refining accumulation rates and the isotopic evolution of the lavas erupted along the southwest rift zone, our new40Ar/39Ar results constrain the eruption of the Ninole Basalts from 227 to 108 ka and provide maximum estimates on the timing of the Ka Lae and South Kona landslides.

The Hydrometallurgical Extraction and Recovery of High-Purity Silver

NASA Astrophysics Data System (ADS)

Hoffmann, James E.

2012-06-01

With the continuous reduction in the availability of extractive metallurgical curricula in colleges and universities, the concern has in part been from where will the next generation of extractive metallurgists come? One objective of this article is to emphasize the fact that extractive metallurgy is, in fact, one of many areas of chemical engineering technology. Thus, although the extractive metallurgist may have disappeared in name, its activity is alive and well, subsumed in the field of chemical engineering. One goal of this lecture is to demonstrate the applicability of chemical engineering principles to what is typically considered "the field of extractive metallurgy." Two processes will be described that have supplanted typical pyrometallurgical fire refining of precious metals, particularly silver. The origins of fire refining can be traced back to biblical times. There are numerous references to it in the old testament: Ezekiel 22:20, "As men gather silver and bronze and iron and lead and tin into a furnace to blow the fire upon it in order melt it"; Jeremiah 6:29, "The bellows blow fiercely; the lead is consumed by the fire; in vain the refining goes on"; and Malachi 3:2 (The Oxford Annotated Bible with the Apocrypha), "For he is like a refiners fire." Many references to it will also be found in "De Re Metallurgica" and as well in Lazarus Ercker's 1574 Manual "Treatise on Ores and Refining." Today, fire refining has been improved greatly by innovative furnace design, new fluxing technologies, and the improved use of oxygen. However, fundamentally, the process chemistry has not changed much in the last millennium. Illustrations of hydrometallurgical processing of silver-bearing inputs will be provided by the treatment of sulfated silver-bearing materials and chlorinated slimes. The first of these technologies will be described briefly as practiced by the Phelps Dodge Refining Corporation for several years. The second, the treatment of silver chloride-bearing inputs, will be described in detail to demonstrate how typical chemical engineering unit process and unit operations have supplanted classic smelting and fire refining techniques. The Kennecott Copper Company, which has operated a hydrometallurgical circuit successfully for the recovery of high-purity silver from the slimes wet chlorination residue, has permitted me to provide some operation information and results using the technology. Both Phelps Dodge and Kennecott should be recognized for their forward-looking attitude in undertaking the conversion of conceptual chemistry into successful, full-scale plants. The process as employed at Phelps Dodge is discussed at length in reference (J.E. Hoffmann and B. Wesstrom: Hydrometallurgy, 1994, vol. 94, pp. 69-105).

[RESULTS OF DUST FACTOR IN COPPER PYROMETALLURGY].

PubMed

Adrianovskiy, V I; Lipatov, G Ya; Zebzeeva, N V; Kuzmina, E A

2016-01-01

The dust entering the air of the working zone of metallurgical shops was shown to be presented by a disintegration aerosols originating in crushing and transporting ore materials and condensation occurring in the course of smelting, converting and fire-refining copper. The overwhelming majority of the grains have a size of 2.1-5.0 mm, which determines a fixed condition of the presence of given dust in the working area, its long presence in the deeper parts of the respiratory system. At the preparatory stages in the composition of the dust there are presented significant amounts of crystalline silicon dioxide possessing of the fibrogenic impact on the body. In the dust the presence of the crystalline silicon dioxide, arsenic, nickel, cadmium determines its carcinogenic hazard. The elevated dustiness of the air is noted with the reflective and especially mine melting, due to the imperfection of the technological equipment and sanitary technical devices. Autogenous smelting processes have demonstrated their hygienic advantage over outdated methods of producing blister copper mining and smelting reflectivity.

Recrystallization texture in nickel heavily deformed by accumulative roll bonding

NASA Astrophysics Data System (ADS)

Mishin, O. V.; Zhang, Y. B.; Godfrey, A.

2017-07-01

The recrystallization behavior of Ni processed by accumulative roll bonding to a total accumulated von Mises strain of 4.8 has been examined, and analyzed with respect to heterogeneity in the deformation microstructure. The regions near the bonding interface are found to be more refined and contain particle deformation zones around fragments of the steel wire brush used to prepare the surface for bonding. Sample-scale gradients are also observed, manifested as differences between the subsurface, intermediate and central layers, where the distributions of texture components are different. These heterogeneities affect the progress of recrystallization. While the subsurface and near-interface regions typically contain lower frequencies of cube-oriented grains than anywhere else in the sample, a strong cube texture forms in the sample during recrystallization, attributed to both a high nucleation rate and fast growth rate of cube-oriented grains. The observations highlight the sensitivity of recrystallization to heterogeneity in the deformation microstructure and demonstrate the importance of characterizing this heterogeneity over several length scales.

Influence of Pressure Field in Melts on the Primary Nucleation in Solidification Processing

NASA Astrophysics Data System (ADS)

Rakita, Milan; Han, Qingyou

2017-10-01

It is well known that external fields applied to melts can cause nucleation at lower supercoolings, fragmentation of growing dendrites, and forced convection around the solidification front. All these effects contribute to a finer microstructure of solidified material. In this article, we analyze how the pressure field created with ultrasonic vibrations influences structure refinement in terms of supercooling. It is shown that only high cavitation pressures of the order of 104 atmospheres are capable of nucleating crystals at minimal supercoolings. We demonstrate the possibility of sononucleation even in superheated liquid. Simulation and experiments with water samples show that very high cavitation pressures occur in a relatively narrow zone where the drive acoustic field has an appropriate combination of pressure amplitude and frequency. In order to accurately predict the microstructure formed by ultrasonically assisted solidification of metals, this article calls for the development of equations of state that would describe the pressure-dependent behavior of molten metals.

The hidden dynamics of relativistic electrons (0.7-1.5 MeV) in the inner zone and slot region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claudepierre, Seth G.; O'Brien, T. P.; Fennell, J. F.

We present measurements of relativistic electrons (0.7–1.5 MeV) in the inner zone and slot region obtained by the Magnetic Electron and Ion Spectrometer (MagEIS) instrument on Van Allen Probes. The data presented are corrected for background contamination, which is primarily due to inner-belt protons in these low-L regions. We find that ~1 MeV electrons were transported into the inner zone following the two largest geomagnetic storms of the Van Allen Probes era to date, the March and June 2015 events. As ~1 MeV electrons were not observed in Van Allen Probes data in the inner zone prior to these twomore » events, the injections created a new inner belt that persisted for at least 1.5 years. In contrast, we find that electrons injected into the slot region decay on much faster timescales, approximately tens of days. Furthermore, we find no evidence of >1.5 MeV electrons in the inner zone during the entire time interval considered (April 2013 through September 2016). The energies we examine thus span a transition range in the steeply falling inner zone electron spectrum, where modest intensities are observed at 0.7 MeV, and no electrons are observed at 1.5 MeV. To validate the results obtained from the background corrected flux measurements, we also present detailed pulse-height spectra from individual MagEIS detectors. These measurements confirm our results and also reveal low-intensity inner zone and slot region electrons that are not captured in the standard background corrected data product. Lastly, we briefly discuss efforts to refine the upper limit of inner zone MeV electron flux obtained in earlier work.« less

The hidden dynamics of relativistic electrons (0.7-1.5 MeV) in the inner zone and slot region

DOE PAGES

Claudepierre, Seth G.; O'Brien, T. P.; Fennell, J. F.; ...

2017-03-15

We present measurements of relativistic electrons (0.7–1.5 MeV) in the inner zone and slot region obtained by the Magnetic Electron and Ion Spectrometer (MagEIS) instrument on Van Allen Probes. The data presented are corrected for background contamination, which is primarily due to inner-belt protons in these low-L regions. We find that ~1 MeV electrons were transported into the inner zone following the two largest geomagnetic storms of the Van Allen Probes era to date, the March and June 2015 events. As ~1 MeV electrons were not observed in Van Allen Probes data in the inner zone prior to these twomore » events, the injections created a new inner belt that persisted for at least 1.5 years. In contrast, we find that electrons injected into the slot region decay on much faster timescales, approximately tens of days. Furthermore, we find no evidence of >1.5 MeV electrons in the inner zone during the entire time interval considered (April 2013 through September 2016). The energies we examine thus span a transition range in the steeply falling inner zone electron spectrum, where modest intensities are observed at 0.7 MeV, and no electrons are observed at 1.5 MeV. To validate the results obtained from the background corrected flux measurements, we also present detailed pulse-height spectra from individual MagEIS detectors. These measurements confirm our results and also reveal low-intensity inner zone and slot region electrons that are not captured in the standard background corrected data product. Lastly, we briefly discuss efforts to refine the upper limit of inner zone MeV electron flux obtained in earlier work.« less

Verifying and Validating Proposed Models for FSW Process Optimization

NASA Technical Reports Server (NTRS)

Schneider, Judith

2008-01-01

This slide presentation reviews Friction Stir Welding (FSW) and the attempts to model the process in order to optimize and improve the process. The studies are ongoing to validate and refine the model of metal flow in the FSW process. There are slides showing the conventional FSW process, a couple of weld tool designs and how the design interacts with the metal flow path. The two basic components of the weld tool are shown, along with geometries of the shoulder design. Modeling of the FSW process is reviewed. Other topics include (1) Microstructure features, (2) Flow Streamlines, (3) Steady-state Nature, and (4) Grain Refinement Mechanisms

Influence of dendrite network defects on channel segregate growth

NASA Technical Reports Server (NTRS)

Simpson, M.; Yerebakan, M.; Flemings, M. C.

1985-01-01

The solidifying ingot interdendritic flow analysis in which channel segregates are assumed to be produced by interdendritic fluid flow dissolving channels in the primary dendrite network is presently refined by examining the flow through a dendrite network possessing a small defect. Attention is given to the section of the mushy zone in a solidifying casting. Since defects such as that presently treated are unavoidable in a real casting, a more reliable indication may be furnished of the occurrence of channel segregates.

Evolution of Overlapping Spreading Centers: A SeaMARC II Investigation

DTIC Science & Technology

1990-06-07

Rhode Island , Narragansett, RI 02882 During a major SeaMARC II expedition in May-June 1987 we happed all the overlapping spreading centers (OSCs) north...Macdonald, 1988, The structural anatomy of the Clipperton and Orozco fracture zones: Sea Beam and SeaMARC II data, EOS Trans., Amer. Geophys. Union...raphy at the University of Rhode Island . most of them are deeper and less ing. Other workers further refined and in 1i.,72 he earned his Ph.D. in marine

Quantitative fabric analysis of eclogite facies mylonites: texture and microtomography

NASA Astrophysics Data System (ADS)

Gomez Barreiro, J.; Voltolini, M.; Martinez-Catalan, J. R.; Benitez-Perez, J. M.; Diez-fernandez, R.; Wenk, H. R.; Vogel, S. C.; Mancini, L.

2014-12-01

Understanding the flow of rock deformed under eclogite facies conditions is crucial to constraint the dynamics of a subducting slab. Prograde metamorphism during burial in a subduction zone proceeds across several lithologies, resulting in heterogeneous eclogitization and potentially different processes. In order to explore the expression of such a variety in terms of a deformative fabric, we have analyzed texture and shape fabric of eclogites and eclogitic orthogneisses from the Malpica-Tui unit (NW Spain). We explore the same rock volumes with TOF-neutron diffraction (HIPPO @ LANSCE) and synchrotron microtomography (SYRMEP @Elettra). Orientation distribution functions were extracted after Rietveld refinement in MAUD and morphometric data (size, aspect ratio, orientation) were obtained after image processing with FIJI, Blob3D and MATLAB. Shape fabric reflects the macroscopic foliation and lineation and correlates with texture. Garnet fabric is particularly important because of the rheological implications of its mechanical behavior. Garnet shows little elongation in both samples, and texture is significant, what probably points to a relatively dry deformative environment, with diffusion-assisted dislocation. This eclogites could represent a rigidification stage in the subduction channel preserved during the exhumation at high-P and high-T documented in the Malpica-Tui unit during the Variscan orogeny.

Investigation on temporal evolution of the grain refinement in copper under high strain rate loading via in-situ synchrotron measurement and predictive modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, Pooja Nitin; Shin, Yung C.; Sun, Tao

Synchrotron X-rays are integrated with a modified Kolsky tension bar to conduct in situ tracking of the grain refinement mechanism operating during the dynamic deformation of metals. Copper with an initial average grain size of 36 μm is refined to 6.3 μm when loaded at a constant high strain rate of 1200 s -1. The synchrotron measurements revealed the temporal evolution of the grain refinement mechanism in terms of the initiation and rate of refinement throughout the loading test. A multiscale coupled probabilistic cellular automata based recrystallization model has been developed to predict the microstructural evolution occurring during dynamic deformationmore » processes. The model accurately predicts the initiation of the grain refinement mechanism with a predicted final average grain size of 2.4 μm. As a result, the model also accurately predicts the temporal evolution in terms of the initiation and extent of refinement when compared with the experimental results.« less

Investigation on temporal evolution of the grain refinement in copper under high strain rate loading via in-situ synchrotron measurement and predictive modeling

DOE PAGES

Shah, Pooja Nitin; Shin, Yung C.; Sun, Tao

2017-10-03

Synchrotron X-rays are integrated with a modified Kolsky tension bar to conduct in situ tracking of the grain refinement mechanism operating during the dynamic deformation of metals. Copper with an initial average grain size of 36 μm is refined to 6.3 μm when loaded at a constant high strain rate of 1200 s -1. The synchrotron measurements revealed the temporal evolution of the grain refinement mechanism in terms of the initiation and rate of refinement throughout the loading test. A multiscale coupled probabilistic cellular automata based recrystallization model has been developed to predict the microstructural evolution occurring during dynamic deformationmore » processes. The model accurately predicts the initiation of the grain refinement mechanism with a predicted final average grain size of 2.4 μm. As a result, the model also accurately predicts the temporal evolution in terms of the initiation and extent of refinement when compared with the experimental results.« less

Building a risk-targeted regional seismic hazard model for South-East Asia

NASA Astrophysics Data System (ADS)

Woessner, J.; Nyst, M.; Seyhan, E.

2015-12-01

The last decade has tragically shown the social and economic vulnerability of countries in South-East Asia to earthquake hazard and risk. While many disaster mitigation programs and initiatives to improve societal earthquake resilience are under way with the focus on saving lives and livelihoods, the risk management sector is challenged to develop appropriate models to cope with the economic consequences and impact on the insurance business. We present the source model and ground motions model components suitable for a South-East Asia earthquake risk model covering Indonesia, Malaysia, the Philippines and Indochine countries. The source model builds upon refined modelling approaches to characterize 1) seismic activity from geologic and geodetic data on crustal faults and 2) along the interface of subduction zones and within the slabs and 3) earthquakes not occurring on mapped fault structures. We elaborate on building a self-consistent rate model for the hazardous crustal fault systems (e.g. Sumatra fault zone, Philippine fault zone) as well as the subduction zones, showcase some characteristics and sensitivities due to existing uncertainties in the rate and hazard space using a well selected suite of ground motion prediction equations. Finally, we analyze the source model by quantifying the contribution by source type (e.g., subduction zone, crustal fault) to typical risk metrics (e.g.,return period losses, average annual loss) and reviewing their relative impact on various lines of businesses.

Characterization and Strain-Hardening Behavior of Friction Stir-Welded Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Sharma, Gaurav; Dwivedi, Dheerendra Kumar; Jain, Pramod Kumar

2017-12-01

In this study, friction stir-welded joint of 3-mm-thick plates of 409 ferritic stainless steel (FSS) was characterized in light of microstructure, x-ray diffraction analysis, hardness, tensile strength, ductility, corrosion and work hardening properties. The FSW joint made of ferritic stainless steel comprises of three distinct regions including the base metal. In stir zone highly refined ferrite grains with martensite and some carbide precipitates at the grain boundaries were observed. X-ray diffraction analysis also revealed precipitation of Cr23C6 and martensite formation in heat-affected zone and stir zone. In tensile testing of the transverse weld samples, the failure eventuated within the gauge length of the specimen from the base metal region having tensile properties overmatched to the as-received base metal. The tensile strength and elongation of the longitudinal (all weld) sample were found to be 1014 MPa and 9.47%, respectively. However, in potentiodynamic polarization test, the corrosion current density of the stir zone was highest among all the three zones. The strain-hardening exponent for base metal, transverse and longitudinal (all weld) weld samples was calculated using various equations. Both the transverse and longitudinal weld samples exhibited higher strain-hardening exponents as compared to the as-received base metal. In Kocks-Mecking plots for the base metal and weld samples at least two stages of strain hardening were observed.

VIEW OF RBC (REFINED BICARBONATE) BUILDING LOOKING NORTHEAST. DEMOLITION IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF RBC (REFINED BICARBONATE) BUILDING LOOKING NORTHEAST. DEMOLITION IN PROGRESS. "ARM & HAMMER BAKING SODA WAS MADE HERE FOR OVER 50 YEARS AND THEN SHIPPED ACROSS THE STREET TO THE CHURCH & DWIGHT PLANT ON WILLIS AVE. (ON THE RIGHT IN THIS PHOTO). LAYING ON THE GROUND IN FRONT OF C&D BUILDING IS PART OF AN RBC DRYING TOWER. - Solvay Process Company, Refined Bicarbonate Building, Between Willis & Milton Avenues, Solvay, Onondaga County, NY

Production of a refined biooil derived by fast pyrolysis of chicken manure with chemical and physical characteristics close to those of fossil fuels.

PubMed

Monreal, Carlos M; Schnitzer, Morris

2011-01-01

The chemical and physical properties of raw biooils prevent their direct use in combustion engines. We processed raw pyrolytic biooil derived from chicken manure to yield a colorless refined biooil with diesel qualities. Chemical characterization of the refined biooil involved elemental and several spectroscopic analyses. The physical measurements employed were viscosity, density and heat of combustion. The elemental composition (% wt/wt) of the refined biooil was 82.7 % C, 15.3 % H, 0.2 % N and 1.8 % O, no S. Its viscosity was 0.006 Pa.s and a heat of combustion of 43 MJ kg(-1). The refined biooil fraction contains n-alkanes, ranging from n-C(14) to n-C(27), alkenes varying from C(10:1) to C(22:1), and long-chain alcohols. The refined biooil makes a good diesel fuel due to its chemical and physical properties.

Use of the Water, Energy, and Biogeochemical Model (WEBMOD) to Simulate Water Quality at Five U.S. Geological Survey Research Watersheds

NASA Astrophysics Data System (ADS)

Webb, R. M.; Leavesley, G. H.; Shanley, J. B.; Peters, N. E.; Aulenbach, B. T.; Blum, A. E.; Campbell, D. H.; Clow, D. W.; Mast, M. A.; Stallard, R. F.; Larsen, M. C.; Troester, J. W.; Walker, J. F.; White, A. F.

2003-12-01

The Water, Energy, and Biogeochemical Model (WEBMOD) was developed as an aid to compare and contrast basic hydrologic and biogeochemical processes active in the diverse hydroclimatic regions represented by the five U.S. Geological Survey (USGS) Water, Energy, and Biogeochemical Budget (WEBB) sites: Loch Vale, Colorado; Trout Lake, Wisconsin; Sleepers River, Vermont; Panola Mountain, Georgia; and Luquillo Experimental Forest, Puerto Rico. WEBMOD simulates solute concentrations for vegetation canopy, snow pack, impermeable ground, leaf litter, unsaturated and saturated soil zones, riparian zones and streams using selected process modules coupled within the USGS Modular Modeling System (MMS). Source codes for the MMS hydrologic modules include the USGS Precipitation Runoff Modeling System, the National Weather Service Hydro-17 snow model, and TOPMODEL. The hydrologic modules distribute precipitation and temperature to predict evapotranspiration, snow accumulation, snow melt, and streamflow. Streamflow generation mechanisms include infiltration excess, saturated overland flow, preferential lateral flow, and base flow. Input precipitation chemistry, and fluxes and residence times predicted by the hydrologic modules are input into the geochemical module where solute concentrations are computed for a series of discrete well-mixed reservoirs using calls to the geochemical engine PHREEQC. WEBMOD was used to better understand variations in water quality observed at the WEBB sites from October 1991 through September 1997. Initial calibrations were completed by fitting the simulated hydrographs with those measured at the watershed outlets. Model performance was then refined by comparing the predicted export of conservative chemical tracers such as chloride, with those measured at the watershed outlets. The model succeeded in duplicating the temporal variability of net exports of major ions from the watersheds.

Feasibility of Department of Defense Used Lubricating Oil Re-refining.

DTIC Science & Technology

1983-12-01

greater product selectivity (increasing cost effec- tiveness by tailoring the process to meet market demand ). In addition most processes have high yields...However, several issues were surfaced. The question of who in DLA is responsible for the administra- tion of a re-refining program must be resolved...Both the Property Disposal and Supply groups have a role. The Disposal group now has responsibility for .1%- iv -. d

The effect of axial external magnetic field on tungsten inert gas welding of magnesium alloy

NASA Astrophysics Data System (ADS)

Li, Caixia; Zhang, Xiaofeng; Wang, Jing

2018-04-01

The influences of axial external magnetic field on the microstructure and mechanical property of the AZ31 magnesium (Mg) alloy joints were studied. The microstructure of Mg alloy joint consisted of the weld seam, heat affected zone and base metal zone. The average grain size of weld seam welded with magnetic field is 39 μm, which is 38% smaller than that of the joint welded with absence of magnetic field. And the microhardness of weld seam increases with the help of magnetic field treatment, owing to the coarse grain refinement. With coil current of 2.0A, the maximum mechanical property of joint increases 6.7% to 255 MPa over the specimen without magnetic field treatment. Furthermore, fracture location is near heat affected area and the fracture surface is characterized with ductile fracture.

An Update of the Analytical Groundwater Modeling to Assess Water Resource Impacts at the Afton Solar Energy Zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quinn, John J.; Greer, Christopher B.; Carr, Adrianne E.

2014-10-01

The purpose of this study is to update a one-dimensional analytical groundwater flow model to examine the influence of potential groundwater withdrawal in support of utility-scale solar energy development at the Afton Solar Energy Zone (SEZ) as a part of the Bureau of Land Management’s (BLM’s) Solar Energy Program. This report describes the modeling for assessing the drawdown associated with SEZ groundwater pumping rates for a 20-year duration considering three categories of water demand (high, medium, and low) based on technology-specific considerations. The 2012 modeling effort published in the Final Programmatic Environmental Impact Statement for Solar Energy Development in Sixmore » Southwestern States (Solar PEIS; BLM and DOE 2012) has been refined based on additional information described below in an expanded hydrogeologic discussion.« less

Wind and Wave Driven Nearshore Circulation at Cape Hatteras Point

NASA Astrophysics Data System (ADS)

Kumar, N.; Voulgaris, G.; Warner, J. C.; List, J. H.

2012-12-01

We have used a measurement and modeling approach to identify hydrodynamic processes responsible for alongshore transport of sediment that can support the maintenance of Diamond Shoals, NC, a large inner-shelf sedimentary convergent feature. As a part of Carolina Coastal Change Processes project, a one month field experiment was conducted around Cape Hatteras point during February, 2010. The instrumentation consisted of 15 acoustic current meters (measuring pressure and velocity profile) deployed in water depths varying from 3-10m and a very high frequency (VHF) beam forming radar system providing surface waves and currents with a resolution of 150 m and a spatial coverage of 10-15 km2. Analysis of field observation suggests that wind-driven circulation and littoral current dominate surf zone and inner shelf processes at least at an order higher than tidally rectified flows. However, the data analysis identified that relevant processes like non-linear advective acceleration, pressure gradient and vortex-force (due to interaction between wave-induced drift and mean flow vorticity), may be significant, but were not assessed accurately due to instrument location and accuracy. To obtain a deeper physical understanding of the hydrodynamics in this study-site, we applied a three-dimensional Coupled-Ocean-Atmosphere-Wave_Sediment-Transport (COAWST) numerical model. The COAWST modeling system is comprised of nested, coupled, three-dimensional ocean-circulation model (ROMS) and wave propagation model (SWAN), configured for the study site to simulate wave height, direction, period and mean current velocities (both Eulerian and Lagrangian). The nesting follows a two-way grid refinement process for the circulation module, and one-way for the wave model. The coarsest parent grid resolved processes on the spatial and temporal scales of mid-shelf to inner-shelf, and subsequent child grids evolved at inner-shelf and surf zone scales. Preliminary results show that the model successfully reproduces wind-driven circulation and littoral currents. Furthermore, model simulation provides evidence for (a) circulation pattern suggesting a mechanism for sediment movement from littoral zone to the Diamond Shoals complex; (b) Diamond shoals complex acting as independent coastline, which restricts the littoral currents to follow the coastline orientation around Cape Hatteras point. As a part of this study, simulated hydrodynamic parameters will be validated against field observations of wave height and direction and Eulerian velocities from acoustic current meters, and sea surface maps of wave height and Lagrangian flows provided by the VHF radar. Moreover, the model results will be analyzed to (a) identify the significance of the terms in momentum balance which are not estimated accurately through field observations; (b) provide a quasi-quantitative estimate of sediment transport contributing to shoal building process.

75 FR 15413 - Approval for Processing Authority, Foreign-Trade Zone 196, ATC Logistics & Electronics (Personal...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-29

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [Order No. 1671] Approval for Processing Authority, Foreign-Trade Zone 196, ATC Logistics & Electronics (Personal Navigation Devices), Fort Worth... & Electronics, an operator of Foreign-Trade Zone 196, has requested processing authority within FTZ 196 in Fort...

Natural attenuation of chlorinated-hydrocarbon contamination at Fort Wainwright, Alaska; a hydrogeochemical and microbiological investigation workplan

USGS Publications Warehouse

McCarthy, Kathleen A.; Lilly, Michael R.; Braddock, Joan F.; Hinzman, Larry D.

1998-01-01

Natural attenuation processes include biological degradation, by which microorganisms break down contaminants into simpler product compounds; adsorption of contaminants to soil particles, which decreases the mass of contaminants dissolved in ground water; and dispersion, which decreases dissolved contaminant concentrations through dilution. The primary objectives of this study are to (1) assess the degree to which such natural processes are attenuating chlorinated-hydrocarbon contamination in ground water, and (2) evaluate the effects of ground-water/surface-water interactions on natural-attenuation processes in the area of the former East and West Quartermasters Fueling Systems for Fort Wainwright, Alaska. The study will include investigations of the hydrologic, geochemical, and microbiological processes occurring at this site that influence the transport and fate of chlorinated hydrocarbons in ground water. To accomplish these objectives, a data-collection program has been initiated that includes measurements of water-table elevations and the stage of the Chena River; measurements of vertical temperature profiles within the subsurface; characterization of moisture distribution and movement in the unsaturated zone; collection of ground-water samples for determination of both organic and inorganic chemical constituents; and collection of ground-water samples for enumeration of microorganisms and determination of their potential to mineralize contaminants. We will use results from the data-collection program described above to refine our conceptual model of hydrology and contaminant attenuation at this site. Measurements of water-table elevations and river stage will help us to understand the magnitude and direction of ground-water flow and how changes in the stage of the Chena River affect ground-water flow. Because ambient ground water and surface water typically have different temperature characteristics, temperature monitoring will likely provide further insight into ground-water/surface-water interactions in the subsurface. Characterization of the unsaturated zone will improve our understanding of interactions among ground water, the unsaturated zone, and the atmosphere. The interactions likely of importance to this study include the migration of water, dissolved contaminants, nutrients, and gases (oxygen, carbon dioxide, and methane) between the saturated and unsaturated zones. We will use the results of ground-water chemical analyses to determine the spatial and temporal distribution of (1) chlorinated-hydrocarbon contaminants and their degradation products, (2) oxidation-reduction indicators, (3) nutrients, and (4) major ground-water ions. These water-quality data will provide insight into ground-water flow directions, interactions between ground water and surface water, attenuation of contaminant concentrations caused by dispersion, and intrinsic microbiological processes. Microbiological analyses will indicate whether microorganisms at the site are capable of degrading the contaminants of interest, and will allow us to estimate their potential to attenuate existing contamination. Physical and chemical data interpreted as part of the analysis of ground water and surface water mixing will improve our understanding of the relationship between water quality and contaminant source mixing.

Data Mining for Tectonic Tremor in a Large Global Seismogram Database using Preprocessed Data Quality Measurements

NASA Astrophysics Data System (ADS)

Rasor, B. A.; Brudzinski, M. R.

2013-12-01

The collision of plates at subduction zones yields the potential for disastrous earthquakes, yet the processes that lead up to these events are still largely unclear and make them difficult to forecast. Recent advancements in seismic monitoring has revealed subtle ground vibrations termed tectonic tremor that occur as long-lived swarms of narrow bandwidth activity, different from local earthquakes of comparable amplitude that create brief signals of broader, higher frequency. The close proximity of detected tremor events to the lower edge of the seismogenic zone along the subduction interface suggests a potential triggering relationship between tremor and megathrust earthquakes. Most tremor catalogs are constructed with detection methods that involve an exhausting download of years of high sample rate seismic data, as well as large computation power to process the large data volume and identify temporal patterns of tremor activity. We have developed a tremor detection method that employs the underutilized Quality Analysis Control Kit (QuACK), originally built to analyze station performance and identify instrument problems across the many seismic networks that contribute data to one of the largest seismogram databases in the world (IRIS DMC). The QuACK dataset stores seismogram amplitudes at a wide range of frequencies calculated every hour since 2005 for most stations achieved in the IRIS DMC. Such a preprocessed dataset is advantageous considering several tremor detection techniques use hourly seismic amplitudes in the frequency band where tremor is most active (2-5 Hz) to characterize the time history of tremor. Yet these previous detection techniques have relied on downloading years of 40-100 sample-per-second data to make the calculations, which typically takes several days on a 36-node high-performance cluster to calculate the amplitude variations for a single station. Processing times are even longer for a recently developed detection algorithm that utilize the ratio of amplitudes between tremor frequencies and those of local earthquakes (10-15 Hz) and surface waves (0.02-0.1 Hz). Using the QuACK dataset, we can make the more advanced calculations in a fraction of the time. This method works well to quickly detect tremor in the Cascadia region by finding similar times of increased tremor activity when comparing across a variety of stations within a 100km radius of a reference station. We confirm the legitimacy of this method by demonstrating comparable results to several previously developed tremor detection techniques despite a much shorter processing time. The rapid processing time has allowed us to refine the detection algorithm by seeking more optimal frequency bands by comparing results from our technique and others, using several stations across the Cascadia subduction zone. As we move forward, we will apply the method to other subduction zones, and ultimately to the vast set of seismic data stored at the IRIS DMC for which tremor has not been previously investigated.

Beyond the principle of plentitude: a review of terrestrial planet habitability.

PubMed

Gaidos, E; Deschenes, B; Dundon, L; Fagan, K; Menviel-Hessler, L; Moskovitz, N; Workman, M

2005-04-01

We review recent work that directly or indirectly addresses the habitability of terrestrial (rocky) planets like the Earth. Habitability has been traditionally defined in terms of an orbital semimajor axis within a range known as the habitable zone, but it is also well known that the habitability of Earth is due to many other astrophysical, geological, and geochemical factors. We focus this review on (1) recent refinements to habitable zone calculations; (2) the formation and orbital stability of terrestrial planets; (3) the tempo and mode of geologic activity (e.g., plate tectonics) on terrestrial planets; (4) the delivery of water to terrestrial planets in the habitable zone; and (5) the acquisition and loss of terrestrial planet carbon and nitrogen, elements that constitute important atmospheric gases responsible for habitable conditions on Earth's surface as well as being the building blocks of the biosphere itself. Finally, we consider recent work on evidence for the earliest habitable environments and the appearance of life itself on our planet. Such evidence provides us with an important, if nominal, calibration point for our search for other habitable worlds.

Beyond Texas City: the state of process safety in the unionized U.S. oil refining industry.

PubMed

McQuiston, Thomas H; Lippin, Tobi Mae; Bradley-Bull, Kristin; Anderson, Joseph; Beach, Josie; Beevers, Gary; Frederick, Randy J; Frederick, James; Greene, Tammy; Hoffman, Thomas; Lefton, James; Nibarger, Kim; Renner, Paul; Ricks, Brian; Seymour, Thomas; Taylor, Ren; Wright, Mike

2009-01-01

The March 2005 British Petroleum (BP) Texas City Refinery disaster provided a stimulus to examine the state of process safety in the U.S. refining industry. Participatory action researchers conducted a nation-wide mail-back survey of United Steelworkers local unions and collected data from 51 unionized refineries. The study examined the prevalence of highly hazardous conditions key to the Texas City disaster, refinery actions to address those conditions, emergency preparedness and response, process safety systems, and worker training. Findings indicate that the key highly hazardous conditions were pervasive and often resulted in incidents or near-misses. Respondents reported worker training was insufficient and less than a third characterized their refineries as very prepared to respond safely to a hazardous materials emergency. The authors conclude that the potential for future disasters plagues the refining industry. In response, they call for effective proactive OSHA regulation and outline ten urgent and critical actions to improve refinery process safety.

A Variable Resolution Atmospheric General Circulation Model for a Megasite at the North Slope of Alaska

NASA Astrophysics Data System (ADS)

Dennis, L.; Roesler, E. L.; Guba, O.; Hillman, B. R.; McChesney, M.

2016-12-01

The Atmospheric Radiation Measurement (ARM) climate research facility has three siteslocated on the North Slope of Alaska (NSA): Barrrow, Oliktok, and Atqasuk. These sites, incombination with one other at Toolik Lake, have the potential to become a "megasite" whichwould combine observational data and high resolution modeling to produce high resolutiondata products for the climate community. Such a data product requires high resolutionmodeling over the area of the megasite. We present three variable resolution atmosphericgeneral circulation model (AGCM) configurations as potential alternatives to stand-alonehigh-resolution regional models. Each configuration is based on a global cubed-sphere gridwith effective resolution of 1 degree, with a refinement in resolution down to 1/8 degree overan area surrounding the ARM megasite. The three grids vary in the size of the refined areawith 13k, 9k, and 7k elements. SquadGen, NCL, and GIMP are used to create the grids.Grids vary based upon the selection of areas of refinement which capture climate andweather processes that may affect a proposed NSA megasite. A smaller area of highresolution may not fully resolve climate and weather processes before they reach the NSA,however grids with smaller areas of refinement have a significantly reduced computationalcost compared with grids with larger areas of refinement. Optimal size and shape of thearea of refinement for a variable resolution model at the NSA is investigated.

Large-scale separation of antipsychotic alkaloids from Rauwolfia tetraphylla L. by pH-zone-refining fast centrifugal partition chromatography.

PubMed

Maurya, Anupam; Gupta, Shikha; Srivastava, Santosh K

2013-01-01

pH-zone-refining centrifugal partition chromatography was successively applied in the large-scale separation of close R(f) antipsychotic indole alkaloids directly from CHCl(3) fraction of Rauwolfia tetraphylla leaves. Two experiments with increasing mass from 500 mg to 3 g of crude alkaloid extracts (1C) of R. tetraphylla were carried out in normal-displacement mode using a two-phase solvent system composed of methyl tert-butyl ether/ACN/water (4:1:5, v/v/v) where HCl (12 mM) was added to the lower aqueous stationary phase as a retainer and triethylamine (5 mM) to the organic mobile phase as an eluter. The two centrifugal partition chromatography separations afforded a total of 162.6 mg of 10-methoxytetrahydroalstonine (1) and 296.5 mg of isoreserpiline (2) in 97% and 95.5% purity, respectively, along with a 400.9 mg mixture of α-yohimbine and reserpiline (3 and 4). Further, this mixture was resolved over medium pressure LC using TLC grade silica gel H (average particle size 10 μm), which afforded 160.4 mg of α-yohimbine (3) and 150.2 mg of reserpiline (4) in >95% purities. The purity of the isolated antipsychotic alkaloids was analyzed by high-performance LC and their structures were characterized on the basis of their 1D, 2D NMR and electrospray ionization-mass spectroscopic data. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microstructure and wear resistance of Al2O3-M7C3/Fe composite coatings produced by laser controlled reactive synthesis

NASA Astrophysics Data System (ADS)

Tan, Hui; Luo, Zhen; Li, Yang; Yan, Fuyu; Duan, Rui

2015-05-01

Based on the principle of thermite reaction of Al and Fe2O3 powders, the Al2O3 ceramic reinforced Fe-based composite coatings were fabricated on a steel substrate by laser controlled reactive synthesis and cladding. The effects of different additions of thermite reactants on the phase transition, microstructure evolution, microhardness and wear resistance of the composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Vickers microhardness and block-on-ring wear test, respectively. The results show that Al2O3 ceramic and M7C3 carbide are in situ synthesized via the laser controlled reactive synthesis. The Al2O3 ceramic and M7C3 carbides prefer to distribute along the γ-Fe phase boundary continuously, which separates the γ-Fe matrix and is beneficial to the grain refinement. With the increase of thermite reactants, the amount of Al2O3 ceramic and M7C3 carbide in the composite coatings increases gradually. Moreover the cladding layer changes from dendritic structure to columnar structure and martensite structure in the heat affected zone becomes coarse. The increased thermite reactants improve the microhardness and wear resistance of the in situ composite coatings obviously and enhance the hardness of the heat affected zone, which should be ascribed to the grain refinement, ceramic and carbide precipitation and solid solution strengthening.

Boundaries of intergrowths between mineral individuals: A zone of secondary mineral formation in aggregates

NASA Astrophysics Data System (ADS)

Brodskaya, R. L.; Bil'Skaya, I. V.; Lyakhnitskaya, V. D.; Markovsky, B. A.; Sidorov, E. G.

2007-12-01

Intergrowth boundaries between mineral individuals in dunite of the Gal’moenan massif in Koryakia was studied in terms of crystal morphology, crystal optics, and ontogenesis. The results obtained allowed us to trace the staged formation of olivine and chromite and four generations of these minerals. Micro-and nanotopography of boundary surfaces between intergrown mineral individuals of different generations was examined with optic, electron, and atomic force microscopes. The boundaries between mineral individuals of different generations are distinguished by their microsculpture for both olivine and chromite grains. Both minerals demonstrate a compositional trend toward refinement from older to younger generations. The decrease in the iron mole fraction in olivine and chromite is accompanied by the crystallization of magnetite along weakened zones in olivine of the first generation and as outer rims around the chromite grains of the second generation observable under optic and electronic microscopes. The subsequent refinement of chromite results in the release of PGE from its lattice, as established by atomic power microscopy. The newly formed PGM are localized at the boundaries between mineral individuals and, thus, mark a special stage in the ontogenetic evolution of mineral aggregates. Further recrystallization is expressed in the spatial redistribution of grain boundaries and the formation of monomineralic intergrowth boundaries, i.e., the glomerogranular structure of rock and substructures of PGM, chromite, and olivine grains as intermediate types of organization of the granular assemblies in the form of reticulate, chain, and cellular structures and substructures of aggregates.

Characterization of acoustic cavitation in water and molten aluminum alloy.

PubMed

Komarov, Sergey; Oda, Kazuhiro; Ishiwata, Yasuo; Dezhkunov, Nikolay

2013-03-01

High-intensive ultrasonic vibrations have been recognized as an attractive tool for refining the grain structure of metals in casting technology. However, the practical application of ultrasonics in this area remains rather limited. One of the reasons is a lack of data needed to optimize the ultrasonic treatment conditions, particularly those concerning characteristics of cavitation zone in molten aluminum. The main aim of the present study was to investigate the intensity and spectral characteristics of cavitation noise generated during radiation of ultrasonic waves into water and molten aluminum alloys, and to establish a measure for evaluating the cavitation intensity. The measurements were performed by using a high temperature cavitometer capable of measuring the level of cavitation noise within five frequency bands from 0.01 to 10MHz. The effect of cavitation treatment was verified by applying high-intense ultrasonic vibrations to a DC caster to refine the primary silicon grains of a model Al-17Si alloy. It was found that the level of high frequency noise components is the most adequate parameter for evaluating the cavitation intensity. Based on this finding, it was concluded that implosions of cavitation bubbles play a decisive role in refinement of the alloy structure. Copyright © 2012 Elsevier B.V. All rights reserved.

Kinetic Modeling of a Silicon Refining Process in a Moist Hydrogen Atmosphere

NASA Astrophysics Data System (ADS)

Chen, Zhiyuan; Morita, Kazuki

2018-03-01

We developed a kinetic model that considers both silicon loss and boron removal in a metallurgical grade silicon refining process. This model was based on the hypotheses of reversible reactions. The reaction rate coefficient kept the same form but error of terminal boron concentration could be introduced when relating irreversible reactions. Experimental data from published studies were used to develop a model that fit the existing data. At 1500 °C, our kinetic analysis suggested that refining silicon in a moist hydrogen atmosphere generates several primary volatile species, including SiO, SiH, HBO, and HBO2. Using the experimental data and the kinetic analysis of volatile species, we developed a model that predicts a linear relationship between the reaction rate coefficient k and both the quadratic function of p(H2O) and the square root of p(H2). Moreover, the model predicted the partial pressure values for the predominant volatile species and the prediction was confirmed by the thermodynamic calculations, indicating the reliability of the model. We believe this model provides a foundation for designing a silicon refining process with a fast boron removal rate and low silicon loss.

Kinetic Modeling of a Silicon Refining Process in a Moist Hydrogen Atmosphere

NASA Astrophysics Data System (ADS)

Chen, Zhiyuan; Morita, Kazuki

2018-06-01

We developed a kinetic model that considers both silicon loss and boron removal in a metallurgical grade silicon refining process. This model was based on the hypotheses of reversible reactions. The reaction rate coefficient kept the same form but error of terminal boron concentration could be introduced when relating irreversible reactions. Experimental data from published studies were used to develop a model that fit the existing data. At 1500 °C, our kinetic analysis suggested that refining silicon in a moist hydrogen atmosphere generates several primary volatile species, including SiO, SiH, HBO, and HBO2. Using the experimental data and the kinetic analysis of volatile species, we developed a model that predicts a linear relationship between the reaction rate coefficient k and both the quadratic function of p(H2O) and the square root of p(H2). Moreover, the model predicted the partial pressure values for the predominant volatile species and the prediction was confirmed by the thermodynamic calculations, indicating the reliability of the model. We believe this model provides a foundation for designing a silicon refining process with a fast boron removal rate and low silicon loss.

The Processes Involved in Designing Software.

DTIC Science & Technology

1980-08-01

repeats Itself at the next level, terminating with a plan whose individual steps can be executed to solve the Initial problem. Hayes-Roth and Hayes-Roth...that the original design problem is decomposed into a collection of well structured subproblems under the control of some type of executive process...given element to refine further, the schema is assumed to execute to completion, developing a solution model for that element and refining it into a

Dual mechanisms of grain refinement in a FeCoCrNi high-entropy alloy processed by high-pressure torsion

PubMed Central

Wu, Wenqian; Song, Min; Ni, Song; Wang, Jingshi; Liu, Yong; Liu, Bin; Liao, Xiaozhou

2017-01-01

An equiatomic FeCoCrNi high-entropy alloy with a face-centered cubic structure was fabricated by a powder metallurgy route, and then processed by high-pressure torsion. Detailed microscopy investigations revealed that grain refinement from coarse grains to nanocrystalline grains occurred mainly via concurrent nanoband (NB) subdivision and deformation twinning. NB–NB, twin–NB and twin–twin interactions contributed to the deformation process. The twin–twin interactions resulted in severe lattice distortion and accumulation of high densities of dislocations in the interaction areas. With increasing strain, NB subdivision and interactions between primary twins and inclined secondary stacking faults (SFs)/nanotwins occurred. Secondary nanotwins divided the primary twins into many equiaxed parts, leading to further grain refinement. The interactions between secondary SFs/nanotwins associated with the presence of Shockley partials and primary twins also transformed the primary twin boundaries into incoherent high-angle grain boundaries. PMID:28429759

Vanishing Point Extraction and Refinement for Robust Camera Calibration

PubMed Central

Tsai, Fuan

2017-01-01

This paper describes a flexible camera calibration method using refined vanishing points without prior information. Vanishing points are estimated from human-made features like parallel lines and repeated patterns. With the vanishing points extracted from the three mutually orthogonal directions, the interior and exterior orientation parameters can be further calculated using collinearity condition equations. A vanishing point refinement process is proposed to reduce the uncertainty caused by vanishing point localization errors. The fine-tuning algorithm is based on the divergence of grouped feature points projected onto the reference plane, minimizing the standard deviation of each of the grouped collinear points with an O(1) computational complexity. This paper also presents an automated vanishing point estimation approach based on the cascade Hough transform. The experiment results indicate that the vanishing point refinement process can significantly improve camera calibration parameters and the root mean square error (RMSE) of the constructed 3D model can be reduced by about 30%. PMID:29280966

Increasingly automated procedure acquisition in dynamic systems

NASA Technical Reports Server (NTRS)

Mathe, Nathalie; Kedar, Smadar

1992-01-01

Procedures are widely used by operators for controlling complex dynamic systems. Currently, most development of such procedures is done manually, consuming a large amount of paper, time, and manpower in the process. While automated knowledge acquisition is an active field of research, not much attention has been paid to the problem of computer-assisted acquisition and refinement of complex procedures for dynamic systems. The Procedure Acquisition for Reactive Control Assistant (PARC), which is designed to assist users in more systematically and automatically encoding and refining complex procedures. PARC is able to elicit knowledge interactively from the user during operation of the dynamic system. We categorize procedure refinement into two stages: diagnosis - diagnose the failure and choose a repair - and repair - plan and perform the repair. The basic approach taken in PARC is to assist the user in all steps of this process by providing increased levels of assistance with layered tools. We illustrate the operation of PARC in refining procedures for the control of a robot arm.

Material Interactions in a Novel Pinless Tool Approach to Friction Stir Spot Welding Thin Aluminum Sheet

NASA Astrophysics Data System (ADS)

Bakavos, Dimitrios; Chen, Yingchun; Babout, Laurent; Prangnell, Phil

2011-05-01

The requirement for a probe, or pin, in friction stir spot welding (FSSW) leads to an undesirable keyhole and "hooking," which can influence the fracture path and weld strength. Furthermore, the full weld cycle for FSSW is typically longer than ideal for the automotive industry, being 2 to 5 seconds. Here, it is shown that using a novel pinless tool design it is possible to achieve high lap shear strength (~3.4 kN) in thin aluminum sheet (~1 mm thick), with short weld cycle times (<1 second). Several techniques have been exploited to study the material flow and mechanisms of weld formation in pinless FSSW, including high-resolution X-ray tomography, to understand the role of the tool design and weld parameters. Despite the "simple" nature of a pinless tool, material flow in the weld zone was found to be surprisingly complex and strongly influenced by surface features on the tool, which greatly increased the penetration of the plastic zone into the bottom sheet. Because of the rapid thermal cycle and high level of grain refinement, the weld zone was found to develop a higher strength than the parent material with little evidence of a heat affected zone (HAZ) after postweld natural aging.

Evaluation of Ohio work zone speed zones process.

DOT National Transportation Integrated Search

2014-06-01

This report describes the methodology and results of analyses performed to determine the effectiveness of Ohio Department of Transportation processes for establishing work zone speed zones. Researchers observed motorists speed choice upstream of a...

Rare earth elements in pore waters from Cabo Friós western boundary upwelling system

NASA Astrophysics Data System (ADS)

Smoak, J. M.; Silva-Filho, E. V.; Rousseau, T.; Albuquerque, A. L.; Caldeira, P. P.; Moreira, M.

2015-12-01

Rare earth elements (REE) are a group of reactive trace elements in aqueous media, they have a coherent chemical behavior with however a subtle and gradual shift in physicochemical properties allowing their use as tracers of sources and processes. Uncertainties on their oceanic inputs and outputs still remains [Arsouze et al., 2009; Siddall et al., 2008; Tachikawa et al., 2003]. The water-sediment interface were early on identified as a relevant REE source due to the high distribution coefficient between sediments and pore waters [Elderfield and Sholkovitz, 1987] and substantially higher concentration then the water column [Abbott et al., 2015; Haley et al., 2004; Sholkovitz et al., 1989; Soyol-Erdene and Huh, 2013]. Here we present a cross shelf transect of 4 short pore waters REE profiles on a 680 km2 mud bank located in the region of Cabo Frio, Brazil. This study reveals similar trends at the four sites: a REE production zone reflected by a maximum in concentration at the top of the sediment evolving with depth toward a REE consumption zone reflected by a minimum in REE concentrations. PAAS normalized patterns shows 1) a progressive depletion in LREE with depth with HREE/LREE ratios comprised between 1.1 and 1.6 in the 2 first centimeters evolving gradually to ratios comprised between 2.8 and 4.7 above 7 cm 2) A sharp gradient in negative Ce anomaly with Ce/Ce* values reaching 0.3. With maximum Nd concentrations comprised between 780 and 1200 pmol.kg and considering that seawater Nd concentrations of Brazilian shelf bottom waters are comprised between 24 and 50 pmol.Kg-1 we apply the Fick´s First Law of diffusion and estimate that 340 +/- 90 nmol. m-2 Y-1 of Nd is released in the Cabo frio´s mudbank. This flux is in the same order of magnitude of recent estimates by [Abbott et al., 2015] in the slope of Oregon´s margin. Unraveling processes responsible for the REE production zone will help to refine the global REE fluxes estimates.

Impact of Wildfire on Microbial Biomass in Critical Zone Observatory

NASA Astrophysics Data System (ADS)

Murphy, M. A.; Fairbanks, D.; Chorover, J.; Gallery, R. E.; Rich, V. I.

2014-12-01

The recovery of the critical zone following disturbances such as wildfire is not fully understood. Wildfires have increased in size and intensity in western US forests in recent years and these fires influence soil microbial communities, both in composition and overall biomass. Studies have typically shown a 50% post-fire decline in overall microbial biomass (µg per g soil) that can persist for years. There is however, some variability in the severity of biomass decline, and its relationship with burn severity and landscape position have not yet been studied. Since microbial biomass has a cascade of impacts in soil systems, from helping control the rate and diversity the biogeochemical processes occurring, to promoting soil fertility, to impacting the nature and structure of soil carbon (C), fire's lasting impact on it is one mechanistic determinant of the overall post-fire recovery of impacted ecosystems. Additionally, microbial biomass measurements hold potential for testing and incorporation into land surface models (NoahMP, CLM, etc.) in order to improve estimates of long-term effects of climate change and disturbances such as fire on the C cycle. In order to refine our understanding of the impact of fire on microbial biomass and then relate that to biogeochemical processes and ecosystem recovery, we used chloroform fumigation extraction to quantify total microbial biomass C (Cmic ). One year after the June 2013 Thompson Ridge fire in the Jemez River Basin Critical Zone Observatory, we are measuring the Cmic of 22 sites across a gradient of burn severities and 4 control unburned sites, from six depth intervals at each site (0-2, 2-5, 5-10, 10-20, 20-30, and 30-40 cm). We hypothesize that the decrease in microbial biomass in burned sites relative to control sites will correlate with changes in soil biogeochemistry related to burn severity; and that the extent of the impact on biomass will be inversely related to depth in the soil column. Additionally, as the project progresses, we will relate microbial biomass to microbial functional assays as proxy for biogeochemical activity, and test variation by landscape position and aspect.

Layered intrusion formation by top down thermal migration zone refining (Invited)

NASA Astrophysics Data System (ADS)

Lundstrom, C.

2009-12-01

The formation of layered mafic intrusions by crystallization from cooling magmas represents the textbook example of igneous differentiation, often attributed to fractional crystallization through gravitational settling. Yet in detail, such interpretations have significant problems such that it remains unclear how these important features form. Put in the Earth perspective that no km scale blob of >50% melt has ever been imaged geophysically and that geochronological studies repeatedly indicate age inconsistencies with “big tank” magma chambers, it may be questioned if km scale magma chambers have ever existed. I will present the case for forming layered intrusions by a top down process whereby arriving basaltic magma reaches a permeability barrier, begins to underplate and forms the intrusion incrementally by sill injection with the body growing downward at ~1 mm/yr rate or less. A temperature gradient zone occurs in the overlying previously emplaced sills, leading to chemical components migrating by diffusion. As long as the rate of diffusion can keep up with rate of sill addition, the body will differentiate along a path similar to a liquid line of descent. In this talk, I will integrate data from 3 areas: 1) laboratory experiments examining the behavior of partially molten silicates in a temperature gradient (thermal migration); 2) numerical modeling of the moving temperature gradient zone process using IRIDIUM (Boudreau, 2003); 3) measurements of Fe isotope ratios and geochronology from the Sonju Lake Intrusion in the Duluth Complex. This model provides the ability to form km scale intrusions by a seismically invisible means, can explain million year offsets in chronology, and has implications for reef development and PGE concentration. Most importantly, this model of top down layered intrusion formation, following a similar recent proposal for granitoid formation (Lundstrom, 2009), represents a testable hypothesis: because temperature gradient driven diffusion leads to the prediction of heavy isotope ratios near the top of the intrusion and light ratios near the bottom of the intrusion, analyses of Fe, Mg and Si isotopes provide an important new tool for examining igneous differentiation.

Final Project Report: Imaging Fault Zones Using a Novel Elastic Reverse-Time Migration Imaging Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Lianjie; Chen, Ting; Tan, Sirui

Imaging fault zones and fractures is crucial for geothermal operators, providing important information for reservoir evaluation and management strategies. However, there are no existing techniques available for directly and clearly imaging fault zones, particularly for steeply dipping faults and fracture zones. In this project, we developed novel acoustic- and elastic-waveform inversion methods for high-resolution velocity model building. In addition, we developed acoustic and elastic reverse-time migration methods for high-resolution subsurface imaging of complex subsurface structures and steeply-dipping fault/fracture zones. We first evaluated and verified the improved capabilities of our newly developed seismic inversion and migration imaging methods using synthetic seismicmore » data. Our numerical tests verified that our new methods directly image subsurface fracture/fault zones using surface seismic reflection data. We then applied our novel seismic inversion and migration imaging methods to a field 3D surface seismic dataset acquired at the Soda Lake geothermal field using Vibroseis sources. Our migration images of the Soda Lake geothermal field obtained using our seismic inversion and migration imaging algorithms revealed several possible fault/fracture zones. AltaRock Energy, Inc. is working with Cyrq Energy, Inc. to refine the geologic interpretation at the Soda Lake geothermal field. Trenton Cladouhos, Senior Vice President R&D of AltaRock, was very interested in our imaging results of 3D surface seismic data from the Soda Lake geothermal field. He planed to perform detailed interpretation of our images in collaboration with James Faulds and Holly McLachlan of University of Nevada at Reno. Using our high-resolution seismic inversion and migration imaging results can help determine the optimal locations to drill wells for geothermal energy production and reduce the risk of geothermal exploration.« less

The vascularized groin lymph node flap (VGLN): Anatomical study and flap planning using multi-detector CT scanner. The golden triangle for flap harvesting.

PubMed

Zeltzer, Assaf A; Anzarut, Alexander; Braeckmans, Delphine; Seidenstuecker, Katrin; Hendrickx, Benoit; Van Hedent, Eddy; Hamdi, Moustapha

2017-09-01

A growing number of surgeons perform lymph node transfers for the treatment of lymphedema. When harvesting a vascularized lymph node groin flap (VGLNF) one of the major concerns is the potential risk of iatrogenic lymphedema of the donor-site. This article helps understanding of the lymph node distribution of the groin in order to minimize this risk. Fifty consecutive patients undergoing abdominal mapping by multi-detector CT scanner were included and 100 groins analyzed. The groin was divided in three zones (of which zone II is the safe zone) and lymph nodes were counted and mapped with their distances to anatomic landmarks. Further node units were plotted and counted. The average age was 48 years. A mean number of nodes of 6.5/groin was found. In zone II, which is our zone of interest a mean of 3.1 nodes were counted with a mean size of 7.8 mm. In three patients no nodes were found in zone II. In five patients nodes were seen in zone II but were not sufficient in size or number to be considered a lymph node unit. On average the lymph node unit in zone II was found to be 48.3 mm from the pubic tubercle when projected on a line from the pubic tubercle to the anterior superior iliac spine, 16.0 mm caudal to this line, and 20.4 mm above the groin crease. On average the lymph node unit was a mean of 41.7 mm lateral to the SCIV-SIEV confluence. This study provides increased understanding of the lymphatic anatomy in zone II of the groin flap and suggests a refined technique for designing the VGLNF. As with any flap there is a degree of individual patient variability. However, having information on the most common anatomy and flap design is of great value. © 2017 Wiley Periodicals, Inc.

Origin of the Louisville Ridge and its relationship to the Eltanin Fracture Zone System

NASA Astrophysics Data System (ADS)

Watts, A. B.; Weissel, J. K.; Duncan, R. A.; Larson, R. L.

1988-04-01

We have combined shipboard and Seasat altimeter derived data in an intergrated geological and geophysical study of the Louisville Ridge; a 3500-km-long seamount chain extending from the Tonga trench to the Eltanin Fracture Zone. A break in the smooth trend of the ridge at latitude 37.5°S has been recognized in both bathymetric and altimetric data. The 40Ar-39Ar dating of rocks dredged either side of the break suggest that it is analogous to the bend in the Hawaiian-Emperor seamount chain. Although the general trend of the ridge can be fit by small circles about Pacific absolute motion poles determined from other seamount chains, the new bathymetric and age data allow us to refine Pacific absolute motion poles. The continuity in smooth trend of the ridge and the Eltanin Fracture Zone suggests some relationship between them. However, a major offset developed on this transform between 60 and 80 Ma, prior to the oldest dated rocks from the ridge. Although magmatism was more or less continuous on the ridge during 28-60 Ma, it probably occurred on crust with little or no offset. Thus magmatism appears to have been little influenced by the developing fracture zone. By 28 Ma, the distance between the magmatic source and the fracture zone had decreased sufficiently for a portion of the ridge to have been emplaced on crust with an offset. After about 12 Ma, however, volcanic activity on the Louisville Ridge apparently waned, despite a possible influence on the magmatism of the fracture zone.

Numerical Modeling of Thermal-Hydrology in the Near Field of a Generic High-Level Waste Repository

NASA Astrophysics Data System (ADS)

Matteo, E. N.; Hadgu, T.; Park, H.

2016-12-01

Disposal in a deep geologic repository is one of the preferred option for long term isolation of high-level nuclear waste. Coupled thermal-hydrologic processes induced by decay heat from the radioactive waste may impact fluid flow and the associated migration of radionuclides. This study looked at the effects of those processes in simulations of thermal-hydrology for the emplacement of U. S. Department of Energy managed high-level waste and spent nuclear fuel. Most of the high-level waste sources have lower thermal output which would reduce the impact of thermal propagation. In order to quantify the thermal limits this study concentrated on the higher thermal output sources and on spent nuclear fuel. The study assumed a generic nuclear waste repository at 500 m depth. For the modeling a representative domain was selected representing a portion of the repository layout in order to conduct a detailed thermal analysis. A highly refined unstructured mesh was utilized with refinements near heat sources and at intersections of different materials. Simulations looked at different values for properties of components of the engineered barrier system (i.e. buffer, disturbed rock zone and the host rock). The simulations also looked at the effects of different durations of surface aging of the waste to reduce thermal perturbations. The PFLOTRAN code (Hammond et al., 2014) was used for the simulations. Modeling results for the different options are reported and include temperature and fluid flow profiles in the near field at different simulation times. References:G. E. Hammond, P.C. Lichtner and R.T. Mills, "Evaluating the Performance of Parallel Subsurface Simulators: An Illustrative Example with PFLOTRAN", Water Resources Research, 50, doi:10.1002/2012WR013483 (2014). Sandia National Laboratories is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. SAND2016-7510 A

Neo-Deterministic Seismic Hazard Assessment at Watts Bar Nuclear Power Plant Site, Tennessee, USA

NASA Astrophysics Data System (ADS)

Brandmayr, E.; Cameron, C.; Vaccari, F.; Fasan, M.; Romanelli, F.; Magrin, A.; Vlahovic, G.

2017-12-01

Watts Bar Nuclear Power Plant (WBNPP) is located within the Eastern Tennessee Seismic Zone (ETSZ), the second most naturally active seismic zone in the US east of the Rocky Mountains. The largest instrumental earthquakes in the ETSZ are M 4.6, although paleoseismic evidence supports events of M≥6.5. Events are mainly strike-slip and occur on steeply dipping planes at an average depth of 13 km. In this work, we apply the neo-deterministic seismic hazard assessment to estimate the potential seismic input at the plant site, which has been recently targeted by the Nuclear Regulatory Commission for a seismic hazard reevaluation. First, we perform a parametric test on some seismic source characteristics (i.e. distance, depth, strike, dip and rake) using a one-dimensional regional bedrock model to define the most conservative scenario earthquakes. Then, for the selected scenario earthquakes, the estimate of the ground motion input at WBNPP is refined using a two-dimensional local structural model (based on the plant's operator documentation) with topography, thus looking for site amplification and different possible rupture processes at the source. WBNNP features a safe shutdown earthquake (SSE) design with PGA of 0.18 g and maximum spectral amplification (SA, 5% damped) of 0.46 g (at periods between 0.15 and 0.5 s). Our results suggest that, although for most of the considered scenarios the PGA is relatively low, SSE values can be reached and exceeded in the case of the most conservative scenario earthquakes.

Structure of the solar photosphere studied from the radiation hydrodynamics code ANTARES.

PubMed

Leitner, P; Lemmerer, B; Hanslmeier, A; Zaqarashvili, T; Veronig, A; Grimm-Strele, H; Muthsam, H J

2017-01-01

The ANTARES radiation hydrodynamics code is capable of simulating the solar granulation in detail unequaled by direct observation. We introduce a state-of-the-art numerical tool to the solar physics community and demonstrate its applicability to model the solar granulation. The code is based on the weighted essentially non-oscillatory finite volume method and by its implementation of local mesh refinement is also capable of simulating turbulent fluids. While the ANTARES code already provides promising insights into small-scale dynamical processes occurring in the quiet-Sun photosphere, it will soon be capable of modeling the latter in the scope of radiation magnetohydrodynamics. In this first preliminary study we focus on the vertical photospheric stratification by examining a 3-D model photosphere with an evolution time much larger than the dynamical timescales of the solar granulation and of particular large horizontal extent corresponding to [Formula: see text] on the solar surface to smooth out horizontal spatial inhomogeneities separately for up- and downflows. The highly resolved Cartesian grid thereby covers [Formula: see text] of the upper convection zone and the adjacent photosphere. Correlation analysis, both local and two-point, provides a suitable means to probe the photospheric structure and thereby to identify several layers of characteristic dynamics: The thermal convection zone is found to reach some ten kilometers above the solar surface, while convectively overshooting gas penetrates even higher into the low photosphere. An [Formula: see text] wide transition layer separates the convective from the oscillatory layers in the higher photosphere.

Structure of the solar photosphere studied from the radiation hydrodynamics code ANTARES

NASA Astrophysics Data System (ADS)

Leitner, P.; Lemmerer, B.; Hanslmeier, A.; Zaqarashvili, T.; Veronig, A.; Grimm-Strele, H.; Muthsam, H. J.

2017-09-01

The ANTARES radiation hydrodynamics code is capable of simulating the solar granulation in detail unequaled by direct observation. We introduce a state-of-the-art numerical tool to the solar physics community and demonstrate its applicability to model the solar granulation. The code is based on the weighted essentially non-oscillatory finite volume method and by its implementation of local mesh refinement is also capable of simulating turbulent fluids. While the ANTARES code already provides promising insights into small-scale dynamical processes occurring in the quiet-Sun photosphere, it will soon be capable of modeling the latter in the scope of radiation magnetohydrodynamics. In this first preliminary study we focus on the vertical photospheric stratification by examining a 3-D model photosphere with an evolution time much larger than the dynamical timescales of the solar granulation and of particular large horizontal extent corresponding to 25''×25'' on the solar surface to smooth out horizontal spatial inhomogeneities separately for up- and downflows. The highly resolved Cartesian grid thereby covers ˜4 Mm of the upper convection zone and the adjacent photosphere. Correlation analysis, both local and two-point, provides a suitable means to probe the photospheric structure and thereby to identify several layers of characteristic dynamics: The thermal convection zone is found to reach some ten kilometers above the solar surface, while convectively overshooting gas penetrates even higher into the low photosphere. An ≈145 km wide transition layer separates the convective from the oscillatory layers in the higher photosphere.

Using toxicokinetic-toxicodynamic modeling as an acute risk assessment refinement approach in vertebrate ecological risk assessment.

PubMed

Ducrot, Virginie; Ashauer, Roman; Bednarska, Agnieszka J; Hinarejos, Silvia; Thorbek, Pernille; Weyman, Gabriel

2016-01-01

Recent guidance identified toxicokinetic-toxicodynamic (TK-TD) modeling as a relevant approach for risk assessment refinement. Yet, its added value compared to other refinement options is not detailed, and how to conduct the modeling appropriately is not explained. This case study addresses these issues through 2 examples of individual-level risk assessment for 2 hypothetical plant protection products: 1) evaluating the risk for small granivorous birds and small omnivorous mammals of a single application, as a seed treatment in winter cereals, and 2) evaluating the risk for fish after a pulsed treatment in the edge-of-field zone. Using acute test data, we conducted the first tier risk assessment as defined in the European Food Safety Authority (EFSA) guidance. When first tier risk assessment highlighted a concern, refinement options were discussed. Cases where the use of models should be preferred over other existing refinement approaches were highlighted. We then practically conducted the risk assessment refinement by using 2 different models as examples. In example 1, a TK model accounting for toxicokinetics and relevant feeding patterns in the skylark and in the wood mouse was used to predict internal doses of the hypothetical active ingredient in individuals, based on relevant feeding patterns in an in-crop situation, and identify the residue levels leading to mortality. In example 2, a TK-TD model accounting for toxicokinetics, toxicodynamics, and relevant exposure patterns in the fathead minnow was used to predict the time-course of fish survival for relevant FOCUS SW exposure scenarios and identify which scenarios might lead to mortality. Models were calibrated using available standard data and implemented to simulate the time-course of internal dose of active ingredient or survival for different exposure scenarios. Simulation results were discussed and used to derive the risk assessment refinement endpoints used for decision. Finally, we compared the "classical" risk assessment approach with the model-based approach. These comparisons showed that TK and TK-TD models can bring more realism to the risk assessment through the possibility to study realistic exposure scenarios and to simulate relevant mechanisms of effects (including delayed toxicity and recovery). Noticeably, using TK-TD models is currently the most relevant way to directly connect realistic exposure patterns to effects. We conclude with recommendations on how to properly use TK and TK-TD model in acute risk assessment for vertebrates. © 2015 SETAC.

Evaluation of the dermal carcinogenicity of lubricant base oils by the mouse skin painting bioassay and other proposed methods.

PubMed

Chasey, K L; McKee, R H

1993-01-01

Lubricant base oils are petroleum products that are predominantly derived from the vacuum distillation of crude oil. Various types of refinement can be employed during the manufacturing process, and evidence suggests that certain of the associated process streams produce skin cancer. Polycyclic aromatic compounds (PACs), some of which are considered as the causative agents, are removed, concentrated or chemically converted during the refinement process. In order to understand the effects of various types of refinement processes on carcinogenic potential, 94 oils were evaluated in the mouse epidermal cancer bioassay. This Exxon database is unique, because of the wide range of crude oils and processing histories represented. Seven processing history classifications are described, and conclusions concerning the impacts of each refinement process on dermal carcinogenicity are discussed. This research also included an evaluation of selected biological and chemical test methods for predicting carcinogenic potential. These included a modified version of the Ames test for mutagenicity, as well as analytical characterizations of the polycyclic aromatic structures in the oils. For classification purposes, a sample was considered to be carcinogenic if it resulted in the production of two or more tumor-bearing animals (in test groups of either 40 or 50 animals). The modified Ames test was considered to be positive if the mutagenicity index was > or = 2.0, and PAC analyses were similarly designated as positive or negative according to proposed guidelines. All of the alternative test methods showed similar agreement with dermal carcinogenicity bioassay data; concordance values were > or = 80%. However, each test was incorrect in ca. 10%-20% of the cases evaluated.(ABSTRACT TRUNCATED AT 250 WORDS)

Close-range sensors for small unmanned bottom vehicles: update

NASA Astrophysics Data System (ADS)

Bernstein, Charles L.

2000-07-01

The Surf Zone Reconnaissance Project is developing sensors for small, autonomous, Underwater Bottom-crawling Vehicles. The objective is to enable small, crawling robots to autonomously detect and classify mines and obstacles on the ocean bottom in depths between 0 and 10 feet. We have identified a promising set of techniques that will exploit the electromagnetic, shape, texture, image, and vibratory- modal features of this images. During FY99 and FY00 we have worked toward refining these techniques. Signature data sets have been collected for a standard target set to facilitate the development of sensor fusion and target detection and classification algorithms. Specific behaviors, termed microbehaviors, are developed to utilize the robot's mobility to position and operate the sensors. A first generation, close-range sensor suite, composed of 5 sensors, will be completed and tested on a crawling platform in FY00, and will be further refined and demonstrated in FY01 as part of the Mine Countermeasures 6.3 core program sponsored by the Office of Naval Research.

Preparation of High Purity CdTe for Nuclear Detector: Electrical and Nuclear Characterization

NASA Astrophysics Data System (ADS)

Zaiour, A.; Ayoub, M.; Hamié, A.; Fawaz, A.; Hage-ali, M.

High purity crystal with controllable electrical properties, however, control of the electrical properties of CdTe has not yet been fully achieved. Using the refined Cd and Te as starting materials, extremely high-purity CdTe single crystals were prepared by the traditional vertical THM. The nature of the defects involved in the transitions was studied by analyzing the position of the energy levels by TSC method. The resolution of 4.2 keV (FWHM) confirms the high quality and stability of the detectors: TSC spectrum was in coherence with detectors spectrum with a horizontal plate between 0.2 and 0.6 eV. The enhancement in resolution of detectors with a full width at half- maximum (less than 0.31 meV), lead to confirm that the combination of vacuum distillation and zone refining was very effective to obtain more purified CdTe single crystals for photovoltaic or nuclear detectors with better physical properties.

Occupational health risk assessment of volatile organic compounds emitted from the coke production unit of a steel plant.

PubMed

Dehghani, Fateme; Omidi, Fariborz; Heravizadeh, Omidreza; Barati Chamgordani, Saied; Gharibi, Vahid; Sotoudeh Manesh, Akbar

2018-03-27

In this study, cancer and non-cancer risks of exposure to volatile organic compounds in the coke production unit of a steel plant were evaluated. To determine individual exposure to benzene, toluene, xylene and ethylbenzene, personal samples were taken from the breathing zone of workers according to National Institute for Occupational Safety and Health (NIOSH) method 1501. Cancer and non-cancer risk assessment was performed, using US Environmental Protection Agency (US EPA) methods. Samples analysis showed that the concentration of benzene in the energy and biochemistry and the benzol refinement sections was higher than occupational exposure limits. The cancer risk for benzene in all sections was significantly higher than allowable limit; the non-cancer risk for benzene in all sections and toluene in the benzol refinement section was also higher than 1.0. In conclusion, the current control measures are not sufficient and should be improved for efficient control of occupational exposures.

Mixing geometric and radiometric features for change classification

NASA Astrophysics Data System (ADS)

Fournier, Alexandre; Descombes, Xavier; Zerubia, Josiane

2008-02-01

Most basic change detection algorithms use a pixel-based approach. Whereas such approach is quite well defined for monitoring important area changes (such as urban growth monitoring) in low resolution images, an object based approach seems more relevant when the change detection is specifically aimed toward targets (such as small buildings and vehicles). In this paper, we present an approach that mixes radiometric and geometric features to qualify the changed zones. The goal is to establish bounds (appearance, disappearance, substitution ...) between the detected changes and the underlying objects. We proceed by first clustering the change map (containing each pixel bitemporal radiosity) in different classes using the entropy-kmeans algorithm. Assuming that most man-made objects have a polygonal shape, a polygonal approximation algorithm is then used in order to characterize the resulting zone shapes. Hence allowing us to refine the primary rough classification, by integrating the polygon orientations in the state space. Tests are currently conducted on Quickbird data.

Forward and inverse solutions for three-element Risley prism beam scanners.

PubMed

Li, Anhu; Liu, Xingsheng; Sun, Wansong

2017-04-03

Scan blind zone and control singularity are two adverse issues for the beam scanning performance in double-prism Risley systems. In this paper, a theoretical model which introduces a third prism is developed. The critical condition for a fully eliminated scan blind zone is determined through a geometric derivation, providing several useful formulae for three-Risley-prism system design. Moreover, inverse solutions for a three-prism system are established, based on the damped least-squares iterative refinement by a forward ray tracing method. It is shown that the efficiency of this iterative calculation of the inverse solutions can be greatly enhanced by a numerical differentiation method. In order to overcome the control singularity problem, the motion law of any one prism in a three-prism system needs to be conditioned, resulting in continuous and steady motion profiles for the other two prisms.

Developments in Characterizing Capture Zone Distributions in Island Growth

NASA Astrophysics Data System (ADS)

Einstein, T. L.; Pimpinelli, Alberto; GonzáLez, Diego Luis; Sathiyanarayanan, Rajesh

2013-03-01

The utility of using the distribution of capture zones (CZD) to characterize epitaxial growth continues to mount. For non-Poisson deposition (i.e. when island nucleation is not fully random) the areas of these Voronoi cells (proximity polygons) can be well described by the generalized Wigner distribution (GWD), particularly in the central region around the mean area. We discuss several recent applications to experimental systems, showing how this perspective leads to insights about the critical nucleus size. In contrast, several studies have shown that the GWD may not describe the numerical data from painstaking simulations in both tails. We discuss some refinements that have been proposed. Finally, we comment on applications to social phenomena such as area distributions of secondary administrative units (like counties) and of Voronoi cells around Metro stops. Work at UMD supported by NSF-MRSEC Grant DMR 05-20471 and NSF CHE 07-49949

Receiver function imaging of the mantle discontinuties beneath Fennoscandia and northern Europe

NASA Astrophysics Data System (ADS)

Frassetto, Andrew; Thybo, Hans

2010-05-01

Receiver functions from the Mantle Investigations of Norwegian Uplift Structure experiment (MAGNUS) are depth-converted using interval wavespeeds from AK-135 for the 410-km and 660-km discontinuities and combined using common-conversion-point stacking. This preliminary work shows a potentially complex mantle-transition-zone beneath southern Norway, with reduction in the amplitude of the 410-arrival and 20-30 km of shallowing of the 660-arrival beneath the axis of the Oslo Rift. To refine these measurements and place them in a regional context, we incorporate the MAGNUS dataset with permanent stations and previous temporary seismic deployments across Fennoscandia and northern Europe. New constraints on the depth to the lithosphere-asthenosphere boundary and character of the mantle-transition-zone will aid in understanding the causes for potentially recent uplift in the southern Scandes and the region of unusually slow upper mantle resolved beneath the region (Weidle and Maupin, 2008).

Purification of organic nonlinear optical materials for bulk crystal growth from melt

NASA Astrophysics Data System (ADS)

Gebre, Tesfaye; Bhat, Kamala N.; Batra, Ashok K.; Lal, Ravindra B.; Aggarwal, Mohan D.; Penn, Benjamin G.; Frazier, Donald O.

2002-10-01

The techniques developed for purification of nonlinear optical organic materials, such as benzil, 2-methyl-4-nitroaniline (MNA), Dicyanovinyl anisole (DIVA) and its derivatives, nitrophenyl prolinol (NPP) and other Schiff's base compounds, include Kugelrohy method, physical vapor transport, zone refining and recrystallization from the solvent are described. Purity of the materials is tested using differential thermal analysis, gas chromatograph/Mass detector, Fourier Transform Infrared spectroscopy and melting point measurements. The purified materials were later used in the growth of single crystal by Bridgman-Stockbarger and Czochralski techniques.

[Measuring microhardness of laser exposed tooth surface].

PubMed

Florin, R; Herrmann, C; Bernhardt, W

1990-02-01

In principle it is possible to homogenize the enamel surface by melting structural elements with the continuous wave CO2 laser. Using the precision instrument NEOPHOT 2 (Carl Zeiss JENA) the microhardness of extracted laserexposed premolares were tested so as to clarify the functional strain capasity and the mechanical characteristics of laserexposed regions of enamel surfaces. The proven higher hardness in the centre of the laserinduced fusing zones (in comparison with adjacent enamel) objectify an attainable refining of the enamel surface that probably causes an increase in the caries-preventive resistance.

Introduction to the structures and processes of subduction zones

NASA Astrophysics Data System (ADS)

Zheng, Yong-Fei; Zhao, Zi-Fu

2017-09-01

Subduction zones have been the focus of many studies since the advent of plate tectonics in 1960s. Workings within subduction zones beneath volcanic arcs have been of particular interest because they prime the source of arc magmas. The results from magmatic products have been used to decipher the structures and processes of subduction zones. In doing so, many progresses have been made on modern oceanic subduction zones, but less progresses on ancient oceanic subduction zones. On the other hand, continental subduction zones have been studied since findings of coesite in metamorphic rocks of supracrustal origin in 1980s. It turns out that high-pressure to ultrahigh-pressure metamorphic rocks in collisional orogens provide a direct target to investigate the tectonism of subduction zones, whereas oceanic and continental arc volcanic rocks in accretionary orogens provide an indirect target to investigate the geochemistry of subduction zones. Nevertheless, metamorphic dehydration and partial melting at high-pressure to ultrahigh-pressure conditions are tectonically applicable to subduction zone processes at forearc to subarc depths, and crustal metasomatism is the physicochemical mechanism for geochemical transfer from the slab to the mantle in subduction channels. Taken together, these provide us with an excellent opportunity to find how the metamorphic, metasomatic and magmatic products are a function of the structures and processes in both oceanic and continental subduction zones. Because of the change in the thermal structures of subduction zones, different styles of metamorphism, metasomatism and magmatism are produced at convergent plate margins. In addition, juvenile and ancient crustal rocks have often suffered reworking in episodes independent of either accretionary or collisional orogeny, leading to continental rifting metamorphism and thus rifting orogeny for mountain building in intracontinental settings. This brings complexity to distinguish the syn-subduction processes and products from post-subduction processes and products. Nevertheless, available results indicate that our definition and understanding of subduction zone processes and products can be advanced by the convergence of observations and interpretations from geochemical, geological, geophysical and geodynamic studies of both oceanic and continental subduction zones. Therefore, insights into subduction zones can be provided by intergration of different approaches from different targets in the near future.

Introduction to the structures and processes of subduction zones

NASA Astrophysics Data System (ADS)

Zheng, Yong-Fei; Zhao, Zi-Fu

2017-09-01

Subduction zones have been the focus of many studies since the advent of plate tectonics in 1960s. Workings within subduction zones beneath volcanic arcs have been of particular interest because they prime the source of arc magmas. The results from magmatic products have been used to decipher the structures and processes of subduction zones. In doing so, many progresses have been made on modern oceanic subduction zones, but less progresses on ancient oceanic subduction zones. On the other hand, continental subduction zones have been studied since findings of coesite in metamorphic rocks of supracrustal origin in 1980s. It turns out that high-pressure to ultrahigh-pressure metamorphic rocks in collisional orogens provide a direct target to investigate the tectonism of subduction zones, whereas oceanic and continental arc volcanic rocks in accretionary orogens provide an indirect target to investigate the geochemistry of subduction zones. Nevertheless, metamorphic dehydration and partial melting at high-pressure to ultrahigh-pressure conditions are tectonically applicable to subduction zone processes at forearc to subarc depths, and crustal metasomatism is the physicochemical mechanism for geochemical transfer from the slab to the mantle in subduction channels. Taken together, these provide us with an excellent opportunity to find how the metamorphic, metasomatic and magmatic products are a function of the structures and processes in both oceanic and continental subduction zones. Because of the change in the thermal structures of subduction zones, different styles of metamorphism, metasomatism and magmatism are produced at convergent plate margins. In addition, juvenile and ancient crustal rocks have often suffered reworking in episodes independent of either accretionary or collisional orogeny, leading to continental rifting metamorphism and thus rifting orogeny for mountain building in intracontinental settings. This brings complexity to distinguish the syn-subduction processes and products from post-subduction processes and products. Nevertheless, available results indicate that our definition and understanding of subduction zone processes and products can be advanced by the convergence of observations and interpretations from geochemical, geological, geophysical and geodynamic studies of both oceanic and continental subduction zones. Therefore, insights into subduction zones can be provided by integration of different approaches from different targets in the near future.

Evolution of Oxide Inclusions in Si-Mn Killed Steels During Hot-Rolling Process

NASA Astrophysics Data System (ADS)

Yang, Wen; Guo, Changbo; Zhang, Lifeng; Ling, Haitao; Li, Chao

2017-10-01

The evolution of oxide inclusions in Si-Mn killed steels refined by slags of different basicity during a four-pass industrial hot-rolling process was investigated using an automated microscopy system. High-basicity refining slag induced the formation of CaO- and Al2O3-containing inclusions, while refining slag with 0.8 basicity induced dominant inclusions of SiO2 and MnO-SiO2. CaO-SiO2-Al2O3 inclusions mainly formed endogenously during solidification and cooling of Ca-containing steels, where Ca originated from slag-steel reactions. However, the larger-sized higher-CaO inclusions originated from slag entrainment. Different inclusions presented different hot-rolling behaviors. The inclusion composition changed by deformation and new phase formation. The dominant oxide types were unchanged under refinement by low-basicity slag; however, they changed under refinement with high-basicity slag. The deformation index of inclusions decreased with increasing accumulated reduction (AR) of the steel. The difference in deformation index between different inclusion types was the largest in the first rolling stage and decreased in subsequent stages. SiO2-CaO and SiO2-MnO-CaO inclusions had larger deformation indices during hot rolling but smaller indices in the last two stages. High-basicity slag increased inclusion complexity; from the perspective of cold-drawing performance, low-basicity refining slag is better for the industrial production of tire-cord steels.

High rates of organic carbon processing in the hyporheic zone of intermittent streams.

PubMed

Burrows, Ryan M; Rutlidge, Helen; Bond, Nick R; Eberhard, Stefan M; Auhl, Alexandra; Andersen, Martin S; Valdez, Dominic G; Kennard, Mark J

2017-10-16

Organic carbon cycling is a fundamental process that underpins energy transfer through the biosphere. However, little is known about the rates of particulate organic carbon processing in the hyporheic zone of intermittent streams, which is often the only wetted environment remaining when surface flows cease. We used leaf litter and cotton decomposition assays, as well as rates of microbial respiration, to quantify rates of organic carbon processing in surface and hyporheic environments of intermittent and perennial streams under a range of substrate saturation conditions. Leaf litter processing was 48% greater, and cotton processing 124% greater, in the hyporheic zone compared to surface environments when calculated over multiple substrate saturation conditions. Processing was also greater in more saturated surface environments (i.e. pools). Further, rates of microbial respiration on incubated substrates in the hyporheic zone were similar to, or greater than, rates in surface environments. Our results highlight that intermittent streams are important locations for particulate organic carbon processing and that the hyporheic zone sustains this fundamental process even without surface flow. Not accounting for carbon processing in the hyporheic zone of intermittent streams may lead to an underestimation of its local ecological significance and collective contribution to landscape carbon processes.

Mechanical properties and biocorrosion resistance of the Mg-Gd-Nd-Zn-Zr alloy processed by equal channel angular pressing.

PubMed

Zhang, Junyi; Kang, Zhixin; Wang, Fen

2016-11-01

A Mg-Gd-Nd-Zn-Zr alloy was processed by equal channel angular pressing (ECAP) at 375°C. The grain size of Mg-Gd-Nd-Zn-Zr alloy was refined to ~2.5μm with the spherical precipitates (β1 phase) distributing in the matrix. The mechanical properties of ECAPed alloy were significantly improved as a result of the grain refinement and precipitation strengthening. The corrosion rate of the ECAPed magnesium alloy in simulated body fluid dramatically decreased from 0.236mm/a to 0.126mm/a due to the strong basal texture and refined microstructure. This wrought magnesium alloy shows potentials in biomedical application. Copyright © 2016 Elsevier B.V. All rights reserved.

Mobil process converts methanol to high-quality synthetic gasoline

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, A.

1978-12-11

If production of gasoline from coal becomes commercially attractive in the United States, a process under development at the Mobil Research and Development Corp. may compete with better known coal liquefaction processes. Mobil process converts methanol to high-octane, unleaded gasoline; methanol can be produced commercially from coal. If gasoline is the desired product, the Mobil process offers strong technical and cost advantages over H-coal, Exxon donor solvent, solvent-refined coal, and Fischer--Tropsch processes. The cost analysis, contained in a report to the Dept. of Energy, concludes that the Mobil process produces more-expensive liquid products than any other liquefaction process except Fischer--Tropsch.more » But Mobil's process produces ready-to-use gasoline, while the others produce oils which require further expensive refining to yield gasoline. Disadvantages and advantages are discussed.« less

Cultural adaptation and health literacy refinement of a brief depression intervention for Latinos in a low-resource setting.

PubMed

Ramos, Zorangelí; Alegría, Margarita

2014-04-01

Few studies addressing the mental health needs of Latinos describe how interventions are tailored or culturally adapted to address the needs of their target population. Without reference to this process, efforts to replicate results and provide working models of the adaptation process for other researchers are thwarted. The purpose of this article is to describe the process of a cultural adaptation that included accommodations for health literacy of a brief telephone cognitive-behavioral depression intervention for Latinos in low-resource settings. We followed a five-stage approach (i.e., information gathering, preliminary adaptation, preliminary testing, adaptation, and refinement) as described by Barrera, Castro, Strycker, and Toobert (2013) to structure our process. Cultural adaptations included condensation of the sessions, review, and modifications of materials presented to participants including the addition of visual aids, culturally relevant metaphors, values, and proverbs. Feedback from key stakeholders, including clinician and study participants, was fundamental to the adaptation process. Areas for further inquiry and adaptation identified in our process include revisions to the presentation of "cognitive restructuring" to participants and the inclusion of participant beliefs about the cause of their depression. Cultural adaptation is a dynamic process, requiring numerous refinements to ensure that an intervention is tailored and relevant to the target population.

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil.

PubMed

Blom, W Marty; Kruizinga, Astrid G; Rubingh, Carina M; Remington, Ben C; Crevel, René W R; Houben, Geert F

2017-08-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk assessment applied to several scenarios involving food products made with vegetable oils. Variables considered were: a) the estimated production scale of refined peanut oil, b) estimated cross-contact between refined vegetable oils during production, c) the proportion of fat in representative food products and d) the peanut protein concentration in refined peanut oil. For all products examined the predicted risk of objective allergic reactions in peanut-allergic users of the food products was extremely low. The number of predicted reactions ranged depending on the model from a high of 3 per 1000 eating occasions (Weibull) to no reactions (LogNormal). Significantly, all reactions were predicted for allergen intakes well below the amounts reported for the most sensitive individual described in the clinical literature. We conclude that the health risk from cross-contact between vegetable oils and refined peanut oil is negligible. None of the food products would warrant precautionary labelling for peanut according to the VITAL ® programme of the Allergen Bureau. Copyright © 2017 Elsevier Ltd. All rights reserved.

Adaptive mesh refinement and front-tracking for shear bands in an antiplane shear model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garaizar, F.X.; Trangenstein, J.

1998-09-01

In this paper the authors describe a numerical algorithm for the study of hear-band formation and growth in a two-dimensional antiplane shear of granular materials. The algorithm combines front-tracking techniques and adaptive mesh refinement. Tracking provides a more careful evolution of the band when coupled with special techniques to advance the ends of the shear band in the presence of a loss of hyperbolicity. The adaptive mesh refinement allows the computational effort to be concentrated in important areas of the deformation, such as the shear band and the elastic relief wave. The main challenges are the problems related to shearmore » bands that extend across several grid patches and the effects that a nonhyperbolic growth rate of the shear bands has in the refinement process. They give examples of the success of the algorithm for various levels of refinement.« less

Implementation of a parallel protein structure alignment service on cloud.

PubMed

Hung, Che-Lun; Lin, Yaw-Ling

2013-01-01

Protein structure alignment has become an important strategy by which to identify evolutionary relationships between protein sequences. Several alignment tools are currently available for online comparison of protein structures. In this paper, we propose a parallel protein structure alignment service based on the Hadoop distribution framework. This service includes a protein structure alignment algorithm, a refinement algorithm, and a MapReduce programming model. The refinement algorithm refines the result of alignment. To process vast numbers of protein structures in parallel, the alignment and refinement algorithms are implemented using MapReduce. We analyzed and compared the structure alignments produced by different methods using a dataset randomly selected from the PDB database. The experimental results verify that the proposed algorithm refines the resulting alignments more accurately than existing algorithms. Meanwhile, the computational performance of the proposed service is proportional to the number of processors used in our cloud platform.

Implementation of a Parallel Protein Structure Alignment Service on Cloud

PubMed Central

Hung, Che-Lun; Lin, Yaw-Ling

2013-01-01

Protein structure alignment has become an important strategy by which to identify evolutionary relationships between protein sequences. Several alignment tools are currently available for online comparison of protein structures. In this paper, we propose a parallel protein structure alignment service based on the Hadoop distribution framework. This service includes a protein structure alignment algorithm, a refinement algorithm, and a MapReduce programming model. The refinement algorithm refines the result of alignment. To process vast numbers of protein structures in parallel, the alignment and refinement algorithms are implemented using MapReduce. We analyzed and compared the structure alignments produced by different methods using a dataset randomly selected from the PDB database. The experimental results verify that the proposed algorithm refines the resulting alignments more accurately than existing algorithms. Meanwhile, the computational performance of the proposed service is proportional to the number of processors used in our cloud platform. PMID:23671842

Profex: a graphical user interface for the Rietveld refinement program BGMN.

PubMed

Doebelin, Nicola; Kleeberg, Reinhard

2015-10-01

Profex is a graphical user interface for the Rietveld refinement program BGMN . Its interface focuses on preserving BGMN 's powerful and flexible scripting features by giving direct access to BGMN input files. Very efficient workflows for single or batch refinements are achieved by managing refinement control files and structure files, by providing dialogues and shortcuts for many operations, by performing operations in the background, and by providing import filters for CIF and XML crystal structure files. Refinement results can be easily exported for further processing. State-of-the-art graphical export of diffraction patterns to pixel and vector graphics formats allows the creation of publication-quality graphs with minimum effort. Profex reads and converts a variety of proprietary raw data formats and is thus largely instrument independent. Profex and BGMN are available under an open-source license for Windows, Linux and OS X operating systems.

Profex: a graphical user interface for the Rietveld refinement program BGMN

PubMed Central

Doebelin, Nicola; Kleeberg, Reinhard

2015-01-01

Profex is a graphical user interface for the Rietveld refinement program BGMN. Its interface focuses on preserving BGMN’s powerful and flexible scripting features by giving direct access to BGMN input files. Very efficient workflows for single or batch refinements are achieved by managing refinement control files and structure files, by providing dialogues and shortcuts for many operations, by performing operations in the background, and by providing import filters for CIF and XML crystal structure files. Refinement results can be easily exported for further processing. State-of-the-art graphical export of diffraction patterns to pixel and vector graphics formats allows the creation of publication-quality graphs with minimum effort. Profex reads and converts a variety of proprietary raw data formats and is thus largely instrument independent. Profex and BGMN are available under an open-source license for Windows, Linux and OS X operating systems. PMID:26500466

Meshfree truncated hierarchical refinement for isogeometric analysis

NASA Astrophysics Data System (ADS)

Atri, H. R.; Shojaee, S.

2018-05-01

In this paper truncated hierarchical B-spline (THB-spline) is coupled with reproducing kernel particle method (RKPM) to blend advantages of the isogeometric analysis and meshfree methods. Since under certain conditions, the isogeometric B-spline and NURBS basis functions are exactly represented by reproducing kernel meshfree shape functions, recursive process of producing isogeometric bases can be omitted. More importantly, a seamless link between meshfree methods and isogeometric analysis can be easily defined which provide an authentic meshfree approach to refine the model locally in isogeometric analysis. This procedure can be accomplished using truncated hierarchical B-splines to construct new bases and adaptively refine them. It is also shown that the THB-RKPM method can provide efficient approximation schemes for numerical simulations and represent a promising performance in adaptive refinement of partial differential equations via isogeometric analysis. The proposed approach for adaptive locally refinement is presented in detail and its effectiveness is investigated through well-known benchmark examples.

Cortical Feedback Regulates Feedforward Retinogeniculate Refinement

PubMed Central

Thompson, Andrew D; Picard, Nathalie; Min, Lia; Fagiolini, Michela; Chen, Chinfei

2016-01-01

SUMMARY According to the prevailing view of neural development, sensory pathways develop sequentially in a feedforward manner, whereby each local microcircuit refines and stabilizes before directing the wiring of its downstream target. In the visual system, retinal circuits are thought to mature first and direct refinement in the thalamus, after which cortical circuits refine with experience-dependent plasticity. In contrast, we now show that feedback from cortex to thalamus critically regulates refinement of the retinogeniculate projection during a discrete window in development, beginning at postnatal day 20 in mice. Disrupting cortical activity during this window, pharmacologically or chemogenetically, increases the number of retinal ganglion cells innervating each thalamic relay neuron. These results suggest that primary sensory structures develop through the concurrent and interdependent remodeling of subcortical and cortical circuits in response to sensory experience, rather than through a simple feedforward process. Our findings also highlight an unexpected function for the corticothalamic projection. PMID:27545712

Fuel conditioning facility zone-to-zone transfer administrative controls.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, C. L.

2000-06-21

The administrative controls associated with transferring containers from one criticality hazard control zone to another in the Argonne National Laboratory (ANL) Fuel Conditioning Facility (FCF) are described. FCF, located at the ANL-West site near Idaho Falls, Idaho, is used to remotely process spent sodium bonded metallic fuel for disposition. The process involves nearly forty widely varying material forms and types, over fifty specific use container types, and over thirty distinct zones where work activities occur. During 1999, over five thousand transfers from one zone to another were conducted. Limits are placed on mass, material form and type, and container typesmore » for each zone. Ml material and containers are tracked using the Mass Tracking System (MTG). The MTG uses an Oracle database and numerous applications to manage the database. The database stores information specific to the process, including material composition and mass, container identification number and mass, transfer history, and the operators involved in each transfer. The process is controlled using written procedures which specify the zone, containers, and material involved in a task. Transferring a container from one zone to another is called a zone-to-zone transfer (ZZT). ZZTs consist of four distinct phases, select, request, identify, and completion.« less

Best Merge Region Growing Segmentation with Integrated Non-Adjacent Region Object Aggregation

NASA Technical Reports Server (NTRS)

Tilton, James C.; Tarabalka, Yuliya; Montesano, Paul M.; Gofman, Emanuel

2012-01-01

Best merge region growing normally produces segmentations with closed connected region objects. Recognizing that spectrally similar objects often appear in spatially separate locations, we present an approach for tightly integrating best merge region growing with non-adjacent region object aggregation, which we call Hierarchical Segmentation or HSeg. However, the original implementation of non-adjacent region object aggregation in HSeg required excessive computing time even for moderately sized images because of the required intercomparison of each region with all other regions. This problem was previously addressed by a recursive approximation of HSeg, called RHSeg. In this paper we introduce a refined implementation of non-adjacent region object aggregation in HSeg that reduces the computational requirements of HSeg without resorting to the recursive approximation. In this refinement, HSeg s region inter-comparisons among non-adjacent regions are limited to regions of a dynamically determined minimum size. We show that this refined version of HSeg can process moderately sized images in about the same amount of time as RHSeg incorporating the original HSeg. Nonetheless, RHSeg is still required for processing very large images due to its lower computer memory requirements and amenability to parallel processing. We then note a limitation of RHSeg with the original HSeg for high spatial resolution images, and show how incorporating the refined HSeg into RHSeg overcomes this limitation. The quality of the image segmentations produced by the refined HSeg is then compared with other available best merge segmentation approaches. Finally, we comment on the unique nature of the hierarchical segmentations produced by HSeg.

Care zoning in a psychiatric intensive care unit: strengthening ongoing clinical risk assessment.

PubMed

Mullen, Antony; Drinkwater, Vincent; Lewin, Terry J

2014-03-01

To implement and evaluate the care zoning model in an eight-bed psychiatric intensive care unit and, specifically, to examine the model's ability to improve the documentation and communication of clinical risk assessment and management. Care zoning guides nurses in assessing clinical risk and planning care within a mental health context. Concerns about the varying quality of clinical risk assessment prompted a trial of the care zoning model in a psychiatric intensive care unit within a regional mental health facility. The care zoning model assigns patients to one of 3 'zones' according to their clinical risk, encouraging nurses to document and implement targeted interventions required to manage those risks. An implementation trial framework was used for this research to refine, implement and evaluate the impact of the model on nurses' clinical practice within the psychiatric intensive care unit, predominantly as a quality improvement initiative. The model was trialled for three months using a pre- and postimplementation staff survey, a pretrial file audit and a weekly file audit. Informal staff feedback was also sought via surveys and regular staff meetings. This trial demonstrated improvement in the quality of mental state documentation, and clinical risk information was identified more accurately. There was limited improvement in the quality of care planning and the documentation of clinical interventions. Nurses' initial concerns over the introduction of the model shifted into overall acceptance and recognition of the benefits. The results of this trial demonstrate that the care zoning model was able to improve the consistency and quality of risk assessment information documented. Care planning and evaluation of associated outcomes showed less improvement. Care zoning remains a highly applicable model for the psychiatric intensive care unit environment and is a useful tool in guiding nurses to carry out routine patient risk assessments. © 2013 John Wiley & Sons Ltd.

Numerical, micro-mechanical prediction of crack growth resistance in a fibre-reinforced/brittle matrix composite

NASA Technical Reports Server (NTRS)

Jenkins, Michael G.; Ghosh, Asish; Salem, Jonathan A.

1990-01-01

Micromechanics fracture models are incorporated into three distinct fracture process zones which contribute to the crack growth resistance of fibrous composites. The frontal process zone includes microcracking, fiber debonding, and some fiber failure. The elastic process zone is related only to the linear elastic creation of new matrix and fiber fracture surfaces. The wake process zone includes fiber bridging, fiber pullout, and fiber breakage. The R-curve predictions of the model compare well with empirical results for a unidirectional, continuous fiber C/C composite. Separating the contributions of each process zone reveals the wake region to contain the dominant crack growth resistance mechanisms. Fractography showed the effects of the micromechanisms on the macroscopic fracture behavior.

Application of DEN refinement and automated model building to a difficult case of molecular-replacement phasing: the structure of a putative succinyl-diaminopimelate desuccinylase from Corynebacterium glutamicum.

PubMed

Brunger, Axel T; Das, Debanu; Deacon, Ashley M; Grant, Joanna; Terwilliger, Thomas C; Read, Randy J; Adams, Paul D; Levitt, Michael; Schröder, Gunnar F

2012-04-01

Phasing by molecular replacement remains difficult for targets that are far from the search model or in situations where the crystal diffracts only weakly or to low resolution. Here, the process of determining and refining the structure of Cgl1109, a putative succinyl-diaminopimelate desuccinylase from Corynebacterium glutamicum, at ∼3 Å resolution is described using a combination of homology modeling with MODELLER, molecular-replacement phasing with Phaser, deformable elastic network (DEN) refinement and automated model building using AutoBuild in a semi-automated fashion, followed by final refinement cycles with phenix.refine and Coot. This difficult molecular-replacement case illustrates the power of including DEN restraints derived from a starting model to guide the movements of the model during refinement. The resulting improved model phases provide better starting points for automated model building and produce more significant difference peaks in anomalous difference Fourier maps to locate anomalous scatterers than does standard refinement. This example also illustrates a current limitation of automated procedures that require manual adjustment of local sequence misalignments between the homology model and the target sequence.

Application of DEN refinement and automated model building to a difficult case of molecular-replacement phasing: the structure of a putative succinyl-diaminopimelate desuccinylase from Corynebacterium glutamicum

PubMed Central

Brunger, Axel T.; Das, Debanu; Deacon, Ashley M.; Grant, Joanna; Terwilliger, Thomas C.; Read, Randy J.; Adams, Paul D.; Levitt, Michael; Schröder, Gunnar F.

2012-01-01

Phasing by molecular replacement remains difficult for targets that are far from the search model or in situations where the crystal diffracts only weakly or to low resolution. Here, the process of determining and refining the structure of Cgl1109, a putative succinyl-diaminopimelate desuccinylase from Corynebacterium glutamicum, at ∼3 Å resolution is described using a combination of homology modeling with MODELLER, molecular-replacement phasing with Phaser, deformable elastic network (DEN) refinement and automated model building using AutoBuild in a semi-automated fashion, followed by final refinement cycles with phenix.refine and Coot. This difficult molecular-replacement case illustrates the power of including DEN restraints derived from a starting model to guide the movements of the model during refinement. The resulting improved model phases provide better starting points for automated model building and produce more significant difference peaks in anomalous difference Fourier maps to locate anomalous scatterers than does standard refinement. This example also illustrates a current limitation of automated procedures that require manual adjustment of local sequence misalignments between the homology model and the target sequence. PMID:22505259

High-rate squeezing process of bulk metallic glasses

PubMed Central

Fan, Jitang

2017-01-01

High-rate squeezing process of bulk metallic glasses from a cylinder into an intact sheet achieved by impact loading is investigated. Such a large deformation is caused by plastic flow, accompanied with geometrical confinement, shear banding/slipping, thermo softening, melting and joining. Temperature rise during the high-rate squeezing process makes a main effect. The inherent mechanisms are illustrated. Like high-pressure torsion (HPT), equal channel angular pressing (ECAP) and surface mechanical attrition treatments (SMAT) for refining grain of metals, High-Rate Squeezing (HRS), as a multiple-functions technique, not only creates a new road of processing metallic glasses and other metallic alloys for developing advanced materials, but also directs a novel technology of processing, grain refining, coating, welding and so on for treating materials. PMID:28338092

High-rate squeezing process of bulk metallic glasses

NASA Astrophysics Data System (ADS)

Fan, Jitang

2017-03-01

High-rate squeezing process of bulk metallic glasses from a cylinder into an intact sheet achieved by impact loading is investigated. Such a large deformation is caused by plastic flow, accompanied with geometrical confinement, shear banding/slipping, thermo softening, melting and joining. Temperature rise during the high-rate squeezing process makes a main effect. The inherent mechanisms are illustrated. Like high-pressure torsion (HPT), equal channel angular pressing (ECAP) and surface mechanical attrition treatments (SMAT) for refining grain of metals, High-Rate Squeezing (HRS), as a multiple-functions technique, not only creates a new road of processing metallic glasses and other metallic alloys for developing advanced materials, but also directs a novel technology of processing, grain refining, coating, welding and so on for treating materials.

High-rate squeezing process of bulk metallic glasses.

PubMed

Fan, Jitang

2017-03-24

High-rate squeezing process of bulk metallic glasses from a cylinder into an intact sheet achieved by impact loading is investigated. Such a large deformation is caused by plastic flow, accompanied with geometrical confinement, shear banding/slipping, thermo softening, melting and joining. Temperature rise during the high-rate squeezing process makes a main effect. The inherent mechanisms are illustrated. Like high-pressure torsion (HPT), equal channel angular pressing (ECAP) and surface mechanical attrition treatments (SMAT) for refining grain of metals, High-Rate Squeezing (HRS), as a multiple-functions technique, not only creates a new road of processing metallic glasses and other metallic alloys for developing advanced materials, but also directs a novel technology of processing, grain refining, coating, welding and so on for treating materials.

The role of ultrasonic cavitation in refining the microstructure of aluminum based nanocomposites during the solidification process.

PubMed

Xuan, Yang; Nastac, Laurentiu

2018-02-01

Recent studies showed that the microstructure and mechanical properties of aluminum based nanocomposites can be significantly improved when ultrasonic cavitation and solidification processing is used. This is because ultrasonic cavitation processing plays an important role not only in degassing and dispersion of the nanoparticles, but also in breaking up the dendritic grains and refining the as-cast microstructure. In the present study, A356 alloy and Al 2 O 3 nanoparticles are used as the matrix alloy and the reinforcement, respectively. Nanoparticles were added into the molten A356 alloy and dispersed via ultrasonic cavitation processing. Ultrasonic cavitation was applied over various temperature ranges during molten alloy cooling and solidification to investigate the grain structure formation and the nanoparticle dispersion behavior. Optical Microscopy and Scanning Electron Microscopy were used to investigate in detail the differences in the microstructure characteristics and the nanoparticle distribution. Experimental results indicated that the ultrasonic cavitation processing and Al 2 O 3 nanoparticles play an important role for microstructure refinement. In addition, it was shown in this study that the Al 2 O 3 nanoparticles modified the eutectic phase. Copyright © 2017 Elsevier B.V. All rights reserved.

A New Method for Estimation of Emissions and Sources of Measurements Error in the Silicon Refining Process

NASA Astrophysics Data System (ADS)

Næss, Mari k.; Kero, Ida; Tranell, Gabriella

2013-08-01

In the production of metallurgical grade silicon (MG-Si), fugitive emissions are a serious concern due to the health risks associated with the fumes formed in different parts of the production. The fumes are also a potential environmental hazard. Yet, the chemical composition of the fumes from most process steps in the silicon plant, such as oxidative refining ladle, remains unknown. This in turn constitutes a problem with respect to the correct assessment of the environmental impact and working conditions. A comprehensive industrial measurement campaign was performed at the Elkem Salten MG-Si production plant in Norway. Samples of the ingoing and outgoing mass flows were analyzed by high-resolution inductively coupled plasma mass spectrometry, with respect to 62 elements. In every step of the sampling and sample treatment processes, possible sources of error have been identified and quantified, including process variation, mass measurement accuracy, and contamination risk. Total measurement errors for all elements in all phases are established. The method is applied to estimate the order of magnitude of the elemental emissions via the fumes from the tapping and refining processes, with respect to production mass and year. The elements with higher concentrations in the fume than slag and refined silicon include Ag, Bi, Cd, Cu, In, K, Mg, Na, Pb, Rb, Se, Sn, Tl, and Zn: all being present in the ppm range. This work constitutes new and vital information to enable the correct assessment of the environmental impact and working conditions at an MG-Si plant.

Cetane improvement via the DIESEL-B process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dawson, F.N. Jr.

1987-01-01

The DIESEL-B Process is a new process offered by Calsyn which is targeted toward significant cost savings - up to half the cost of conventional cetane improvers. Pay out of the low capital investments - perhaps $0.5 million - may be obtained in some cases in less than one year. The process involves on-site treating of a small slip stream - about 3% of the diesel pool. Refiners have developed quality fuels for diesel engines which would be suitable for the many diverse applications of these engines. Over the years a fair consensus of required quality specifications has evolved, mostmore » importantly those of the major pipeline operators. Ignition characteristics, as defined by cetane number or cetane index have been the most important, but other controls designed to insure stability, color, carbon content and the like are also essential constraints for the refiner. Refiners have historically been able to meet demand for motor diesel fuels by blending the higher quality virgin and hydrotreated materials with a variety of lesser quality stocks, such as cat cracker light cycle oils, coker cycle oils, thermal cycle oils and the like. But because of the typically poor engine performance properties of these latter materials, refiners have had to employ a variety of additives, most importantly cetane improvement additives, cost for which can be substantial. Calsyn is pleased to announce the development of the DIESEL-B Process for improvement of diesel fuel ignition characteristics in response to the growing need for cost cutting methods for the bread and butter portions of our business.« less

Processes for converting lignocellulosics to reduced acid pyrolysis oil

DOEpatents

Kocal, Joseph Anthony; Brandvold, Timothy A

2015-01-06

Processes for producing reduced acid lignocellulosic-derived pyrolysis oil are provided. In a process, lignocellulosic material is fed to a heating zone. A basic solid catalyst is delivered to the heating zone. The lignocellulosic material is pyrolyzed in the presence of the basic solid catalyst in the heating zone to create pyrolysis gases. The oxygen in the pyrolysis gases is catalytically converted to separable species in the heating zone. The pyrolysis gases are removed from the heating zone and are liquefied to form the reduced acid lignocellulosic-derived pyrolysis oil.

Preparation and characterization of semi-refined kappa carrageenan-based edible film for nano coating application on minimally processed food

NASA Astrophysics Data System (ADS)

Manuhara, Godras Jati; Praseptiangga, Danar; Muhammad, Dimas Rahadian Aji; Maimuni, Bawani Hindami

2016-02-01

Shorter and easier processing of semi-refined kappa carrageenan extracted from Euchema cottonii red seaweed result in cheaper price of the polysaccharide. In this study, edible film was prepared from the semi-refined carrageenan without any salt addition. The effect of the carrageenan concentration (1.0, 1.5, and 2.0% w/v) on physical and mechanical properties of the edible film was studied. Edible film thickness and tensile strength increased but elongation at break and water vapor transmission rate (WVTR) decreased as the concentration increased. Based on the characteristic of the edible film, formulation using 2% carrageenan was recommended. The edible film demonstrated the characteristic as follow: 0.054 mm thickness, 21.14 MPa tensile strength, 12.36% elongation at break, and 9.56 g/m2.hour WVTR. It was also noted the carrageenan-based edible film indicated potential physical and mechanical characteristics for nano coating applications on minimally processed food.

Construction and Application of a Refined Hospital Management Chain.

PubMed

Lihua, Yi

2016-01-01

Large scale development was quite common in the later period of hospital industrialization in China. Today, Chinese hospital management faces such problems as service inefficiency, high human resources cost, and low rate of capital use. This study analyzes the refined management chain of Wuxi No.2 People's Hospital. This consists of six gears namely, "organizational structure, clinical practice, outpatient service, medical technology, and nursing care and logistics." The gears are based on "flat management system targets, chief of medical staff, centralized outpatient service, intensified medical examinations, vertical nursing management and socialized logistics." The core concepts of refined hospital management are optimizing flow process, reducing waste, improving efficiency, saving costs, and taking good care of patients as most important. Keywords: Hospital, Refined, Management chain

Grain refinement and texture development of cast bismuth-antimony alloy via severe plastic deformation

NASA Astrophysics Data System (ADS)

Im, Jae-Taek

The purpose of this work was to study learn about grain refinement mechanisms and texture development in cast n-type Bi90Sb10 alloy caused by severe plastic deformation. The practical objective is to produce a fine grained and textured microstructure in Bi90Sb10 alloy with enhanced thermoelectric performance and mechanical strength. In the study, twelve millimeter diameter cast bars of Bi90Sb 10 alloy were encapsulated in square cross section aluminum 6061 alloy containers. The composite bars were equal channel angular (ECAE) extruded through a 90 degree angle die at high homologous temperature. Various extrusion conditions were studied including punch speed (0.1, 0.3 and 0.6 in/min), extrusion temperature (220, 235 and 250°C), number of extrusion passes (1, 2 and 4), route (A, BC and C), and exit channel area reduction ratio (half and quarter area of inlet channel). The affect of an intermediate long term heat treatment (for 100 hours at 250°C under 10-3 torr vacuum) was explored. Processed materials were characterized by optical microscopy, x-ray diffraction, energy dispersive spectroscopy, wavelength dispersive spectroscopy and scanning electron microscopy. Texture was analyzed using the {006} reflection plane to identify the orientation of the basal poles in processed materials. The cast grains were irregularly shaped, had a grain size of hundreds-of-microns to millimeters, and showed inhomogeneous chemical composition. Severe plastic deformation refines the cast grains through dynamic recrystallization and causes the development of a bimodal microstructure consisting of fine grains (5-30 micron) and coarse grains (50-300 micron). ECAE processing of homogenizied Bi-Sb alloy causes grain refinement and produces a more uniform microstructure. Texture results show that ECAE route C processing gives a similar or slightly stronger texture than ECAE route A processing. In both cases, the basal-plane poles become aligned with the shear direction. Reduction area exit channel extrusion is more effective for both grain refinement and texture enhancement than simple ECAE processing.

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selvakumar, S., E-mail: lathaselvam1963@gmail.com

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization andmore » pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.« less

Weathering the Storm: Unmanned Aircraft Systems in the Maritime, Atmospheric and Polar Environments

NASA Technical Reports Server (NTRS)

Fladeland, Matthew M.; Sullivan, Donald V.; Chirayath, Ved; Instrella, Ron; Phelps, Geoffrey

2017-01-01

Remotely piloted aircraft (RPA) have the potential to revolutionize local to regional data collection for geophysicists as platform and payload size decrease while aircraft capabilities increase. In particular, data from RPAs combine high-resolution imagery available from low flight elevations with comprehensive areal coverage, unattainable from ground investigations and difficult to acquire from manned aircraft due to budgetary and logistical costs. Low flight elevations are particularly important for detecting signals that decay exponentially with distance, such as electromagnetic fields. Onboard data processing coupled with high-bandwidth telemetry open up opportunities for real-time and near real-time data processing, producing more efficient flight plans through the use of payload-directed flight, machine learning and autonomous systems. Such applications not only strive to enhance data collection, but also enable novel sensing modalities and temporal resolution. NASAs Airborne Science Program has been refining the capabilities and applications of RPA in support of satellite calibration and data product validation for several decades. In this paper, we describe current platforms, payloads, and onboard data systems available to the research community. Case studies include Fluid Lensing for littoral zone 3D mapping, structure from motion for terrestrial 3D multispectral imaging, and airborne magnetometry on medium and small RPAs.

Strengthening of Cu–Ni–Si alloy using high-pressure torsion and aging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Seungwon, E-mail: chominamlsw@gmail.com; WPI, International Institute for Carbon-Neutral Energy Research; Matsunaga, Hirotaka

2014-04-01

An age-hardenable Cu–2.9%Ni–0.6%Si alloy was subjected to high-pressure torsion. Aging behavior was investigated in terms of hardness, electrical conductivity and microstructural features. Transmission electron microscopy showed that the grain size is refined to ∼ 150 nm and the Vickers microhardness was significantly increased through the HPT processing. Aging treatment of the HPT-processed alloy led to a further increase in the hardness. Electrical conductivity is also improved with the aging treatment. It was confirmed that the simultaneous strengthening by grain refinement and fine precipitation is achieved while maintaining high electrical conductivity. Three dimensional atom probe analysis including high-resolution transmission electron microscopymore » revealed that nanosized precipitates having compositions of a metastable Cu{sub 3}Ni{sub 5}Si{sub 2} phase and a stable NiSi phase were formed in the Cu matrix by aging of the HPT-processed samples and these particles are responsible for the additional increase in strength after the HPT processing. - Highlights: • Grain refinement is achieved in Corson alloy the size of ∼150nm by HPT. • Aging at 300°C after HPT leads to further increase in the mechanical property. • Electrical conductivity reaches 40% IACS after aging for 100 h. • 3D-APT revealed the formation of nanosized-precipitates during aging treatment. • Simultaneous hardening in both grain refinement and precipitation is achieved.« less

Complications at the Proximal Landing Zone of Endovascular Stent Grafts Deployed in Surgically Replaced Ascending Aorta.

PubMed

Kotha, Vamshi K; Herget, Eric J; Appoo, Jehangir J

2016-11-01

The ascending aorta, with its hostile angulations and forces, is the next frontier in the evolution of endovascular surgery. Type II hybrid arch repair, involving surgical replacement of the ascending aorta, arch debranching, and stent graft deployment in the ascending aortic graft, offers an opportunity to study the behavior of an endovascular prosthesis in the ascending aorta. We report complications seen at the proximal landing zone after type II hybrid arch repair. A dedicated imaging protocol was used to monitor 20 consecutive patients who underwent type II hybrid arch repair at a single center from June 2009 to July 2014. Mean age was 66 years (range, 47 to 82 years). Mean imaging follow-up was 34 months (range, 12 to 64 months). There was 1 operative death (5%). Bird beaking (>5 mm of nonapposition) of the stent graft at the proximal landing zone occurred in 12 patients, and >20 mm of bird beaking occurred in 7 patients. Proximal landing zone complications occurred in 4 patients (20%), comprising 2 type Ia endoleaks, 1 graft migration, and 1 graft infolding detected on postoperative days 4, 11, 5, and 755, respectively. Three patients underwent endovascular reintervention for proximal landing zone complications. There were no late deaths. Thoracic aortic stent grafts may be prone to proximal landing zone complications when deployed in the ascending aorta. Bird beaking is common when endografts are deployed in the Dacron (DuPont, Wilmington, DE) ascending aorta. Angulation issues will likely need to be overcome by stent graft refinement to enable future closed chest approaches to the ascending aorta. Copyright © 2016 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Results from the hydrodynamic element of the 1994 entrapment zone study in Suisun Bay

USGS Publications Warehouse

Burau, J.R.; Gartner, J.W.; Stacey, M.

1998-01-01

The entrapment zo as long been considered an important region of the San Francisco estuary. It has been the subject of several previous studies, and its location has been suggested as an index of condition of the estuarine ecosystem.A close correlate of this location, X2 1, is now used as a management objective on the basis that X2 is correlated with the abundance or survival of several estuarine-dependent species. X2 is a crude tool to use for this purpose, but it can be refined only through improved understanding of the various mechanisms underlying these correlations. These mechanisms probably differ among species, but for species resident in and near the entrapment zone, the correlation with X2 may be due to variations in intenSity oftrapping mechanisms with pOSition of the entrapment zone. Therefore, it is worthwhile to investigate these trapping mechanisms, the nature of the entrapment zone as habitat, and the responses of the entrapment zone to changes in X2 or outflow from the Sacramento-San Joaquin Delta. Studies ofthe entrapment zone ofthe San Francisco estuary have been conducted in springs of 1994, 1995, and 1996. These studies have been funded by the Interagency Ecological Program and conducted by scientists from IEP member agencies, the Romberg Tiburon Center for Environmental Studies, Bodega Marine Laboratory, and the University of California at Santa Cruz. This report presents results from 1994, a low-flow year. Subsequent reports will describe results from 1995 and 1996 and highlight differences among years. This report is organized in chapters that comprise more-or-Iess independent papers, with an introductory chapter for the entire study. This Executive Summary presents highlights of the overall study plan and summarizes the major findings.

Shallow subsurface structure of the Wasatch fault, Provo segment, Utah, from integrated compressional and shear-wave seismic reflection profiles with implications for fault structure and development

USGS Publications Warehouse

McBride, J.H.; Stephenson, W.J.; Williams, R.A.; Odum, J.K.; Worley, D.M.; South, J.V.; Brinkerhoff, A.R.; Keach, R.W.; Okojie-Ayoro, A. O.

2010-01-01

Integrated vibroseis compressional and experimental hammer-source, shear-wave, seismic reflection profiles across the Provo segment of the Wasatch fault zone in Utah reveal near-surface and shallow bedrock structures caused by geologically recent deformation. Combining information from the seismic surveys, geologic mapping, terrain analysis, and previous seismic first-arrival modeling provides a well-constrained cross section of the upper ~500 m of the subsurface. Faults are mapped from the surface, through shallow, poorly consolidated deltaic sediments, and cutting through a rigid bedrock surface. The new seismic data are used to test hypotheses on changing fault orientation with depth, the number of subsidiary faults within the fault zone and the width of the fault zone, and the utility of integrating separate elastic methods to provide information on a complex structural zone. Although previous surface mapping has indicated only a few faults, the seismic section shows a wider and more complex deformation zone with both synthetic and antithetic normal faults. Our study demonstrates the usefulness of a combined shallow and deeper penetrating geophysical survey, integrated with detailed geologic mapping to constrain subsurface fault structure. Due to the complexity of the fault zone, accurate seismic velocity information is essential and was obtained from a first-break tomography model. The new constraints on fault geometry can be used to refine estimates of vertical versus lateral tectonic movements and to improve seismic hazard assessment along the Wasatch fault through an urban area. We suggest that earthquake-hazard assessments made without seismic reflection imaging may be biased by the previous mapping of too few faults. ?? 2010 Geological Society of America.

40 CFR 80.513 - What provisions apply to transmix processing facilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... processing. This section applies to refineries that produce diesel fuel from transmix by distillation or other refining processes but do not produce diesel fuel by processing crude oil. This section only...

MCT: A UK Retrospective—Reminiscences of a Crystal Grower

NASA Astrophysics Data System (ADS)

Capper, Peter

2017-09-01

The essentials of bulk Bridgman growth of mercury cadmium telluride (MCT) are outlined, together with some background to its use in the UK. It is still being used in a few niche applications, e.g., long-wavelength photoconductive (PC) detectors for space programs, and as material for infrared (IR) optical components. The latter requires very short-wavelength and/or larger-diameter material, and the challenges and successes in these areas are outlined. Use of a new source of high-purity silica, together with continual improvements in element purification, from our in-house tellurium zone refining and mercury distillation, reduced the carrier concentration consistently to sub-1014 cm-3, which helped to further improve PC device performance. An offer is made to supply bulk wafers to the wider community for research and development (R&D) purposes. The benefits of IR-related books, published over the past 30 years, to the community are described and a challenge laid down to continue this process of information dissemination into the future, in either hard-copy form or online versions.

A new memetic algorithm for mitigating tandem automated guided vehicle system partitioning problem

NASA Astrophysics Data System (ADS)

Pourrahimian, Parinaz

2017-11-01

Automated Guided Vehicle System (AGVS) provides the flexibility and automation demanded by Flexible Manufacturing System (FMS). However, with the growing concern on responsible management of resource use, it is crucial to manage these vehicles in an efficient way in order reduces travel time and controls conflicts and congestions. This paper presents the development process of a new Memetic Algorithm (MA) for optimizing partitioning problem of tandem AGVS. MAs employ a Genetic Algorithm (GA), as a global search, and apply a local search to bring the solutions to a local optimum point. A new Tabu Search (TS) has been developed and combined with a GA to refine the newly generated individuals by GA. The aim of the proposed algorithm is to minimize the maximum workload of the system. After all, the performance of the proposed algorithm is evaluated using Matlab. This study also compared the objective function of the proposed MA with GA. The results showed that the TS, as a local search, significantly improves the objective function of the GA for different system sizes with large and small numbers of zone by 1.26 in average.

Oxidation mechanism of T91 steel in liquid lead-bismuth eutectic: with consideration of internal oxidation

PubMed Central

Ye, Zhongfei; Wang, Pei; Dong, Hong; Li, Dianzhong; Zhang, Yutuo; Li, Yiyi

2016-01-01

Clarification of the microscopic events that occur during oxidation is of great importance for understanding and consequently controlling the oxidation process. In this study the oxidation product formed on T91 ferritic/martensitic steel in oxygen saturated liquid lead-bismuth eutectic (LBE) at 823 K was characterized at the nanoscale using focused-ion beam and transmission electron microscope. An internal oxidation zone (IOZ) under the duplex oxide scale has been confirmed and characterized systematically. Through the microscopic characterization of the IOZ and the inner oxide layer, the micron-scale and nano-scale diffusion of Cr during the oxidation in LBE has been determined for the first time. The micron-scale diffusion of Cr ensures the continuous advancement of IOZ and inner oxide layer, and nano-scale diffusion of Cr gives rise to the typical appearance of the IOZ. Finally, a refined oxidation mechanism including the internal oxidation and the transformation of IOZ to inner oxide layer is proposed based on the discussion. The proposed oxidation mechanism succeeds in bridging the gap between the existing models and experimental observations. PMID:27734928

Results of well-bore flow logging for six water-production wells completed in the Santa Fe Group aquifer system, Albuquerque, New Mexico, 1996-98

USGS Publications Warehouse

Thorn, Conde R.

2000-01-01

Over the last several years, an improved conceptual understanding of the aquifer system in the Albuquerque area, New Mexico, has lead to better knowledge about the location and extent of the aquifer system. This information will aid with the refinement of ground-water simulation and with the location of sites for future water-production wells. With an impeller-type flowmeter, well-bore flow was logged under pumping conditions along the screened interval of the well bore in six City of Albuquerque water-production wells: the Ponderosa 3, Love 6, Volcano Cliffs 1, Gonzales 2, Zamora 2, and Gonzales 3 wells. From each of these six wells, a well-bore flow log was collected that represents the cumulative upward well-bore flow. Evaluation of the well-bore flow log for each well allowed delineation of the more productive zones supplying water to the well along the logged interval. Yields from the more productive zones in the six wells ranged from about 70 to 880 gallons per minute. The lithology of these zones is predominantly gravel and sand with varying amounts of sandy clay.

Spectral properties and ASTER-based alteration mapping of Masahim volcano facies, SE Iran

NASA Astrophysics Data System (ADS)

Tayebi, Mohammad H.; Tangestani, Majid H.; Vincent, Robert K.; Neal, Devin

2014-10-01

This study applies Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data and the Mixture Tuned Matched Filtering (MTMF) algorithm to map the sub-pixel distribution of alteration minerals associated with the Masahim volcano, SE Iran for understanding the spatial relationship between alteration minerals and volcano facies. Investigations of the alteration mineralogy were conducted using field-spectroscopy, X-ray diffraction (XRD) analysis and ASTER Short Wave Infrared (SWIR) spectral data. In order to spectrally characterize the stratovolcano deposits, lithological units and alteration minerals, the volcano was divided into three facies: the Central, Proximal, and Medial-distal facies. The reflectance spectra of rock samples show absorption features of a number of minerals including white mica, kaolinite, montmorillonite, illite, goethite, hematite, jarosite, opal, and chlorite. The end-members of key alteration minerals including sericite (phyllic zone), kaolinite (argillic zone) and chlorite (propylitic zone) were extracted from imagery using the Pixel Purity Index (PPI) method and were used to map alteration minerals. Accuracy assessment through field observations was used to verify the fraction maps. The results showed that most prominent altered rocks situated at the central facies of volcano. The alteration minerals were discriminated with the coefficient of determination (R2) of 0.74, 0.81, and 0.68 for kaolinite, sericite, and chlorite, respectively. The results of this study have the potential to refine the map of alteration zones in the Masahim volcano.

Accurate macromolecular crystallographic refinement: incorporation of the linear scaling, semiempirical quantum-mechanics program DivCon into the PHENIX refinement package

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borbulevych, Oleg Y.; Plumley, Joshua A.; Martin, Roger I.

2014-05-01

Semiempirical quantum-chemical X-ray macromolecular refinement using the program DivCon integrated with PHENIX is described. Macromolecular crystallographic refinement relies on sometimes dubious stereochemical restraints and rudimentary energy functionals to ensure the correct geometry of the model of the macromolecule and any covalently bound ligand(s). The ligand stereochemical restraint file (CIF) requires a priori understanding of the ligand geometry within the active site, and creation of the CIF is often an error-prone process owing to the great variety of potential ligand chemistry and structure. Stereochemical restraints have been replaced with more robust functionals through the integration of the linear-scaling, semiempirical quantum-mechanics (SE-QM)more » program DivCon with the PHENIX X-ray refinement engine. The PHENIX/DivCon package has been thoroughly validated on a population of 50 protein–ligand Protein Data Bank (PDB) structures with a range of resolutions and chemistry. The PDB structures used for the validation were originally refined utilizing various refinement packages and were published within the past five years. PHENIX/DivCon does not utilize CIF(s), link restraints and other parameters for refinement and hence it does not make as many a priori assumptions about the model. Across the entire population, the method results in reasonable ligand geometries and low ligand strains, even when the original refinement exhibited difficulties, indicating that PHENIX/DivCon is applicable to both single-structure and high-throughput crystallography.« less

Mercury Production and Use in Colonial Andean Silver Production: Emissions and Health Implications

PubMed Central

Hagan, Nicole A.

2012-01-01

Background: Colonial cinnabar mining and refining began in Huancavelica, Peru, in 1564. With a local source of mercury, the amalgamation process was adopted to refine silver in Potosí, Bolivia, in the early 1570s. As a result, large quantities of mercury were released into the environment. Objectives: We used archival, primary, and secondary sources to develop the first estimate of mercury emissions from cinnabar refining in Huancavelica and to revise previous estimates of emissions from silver refining in Potosí during the colonial period (1564–1810). Discussion: Although other estimates of historical mercury emissions have recognized Potosí as a significant source, Huancavelica has been overlooked. In addition, previous estimates of mercury emissions from silver refining under-estimated emissions because of unrecorded (contra-band) production and volatilization of mercury during processing and recovery. Archival descriptions document behavioral and health issues during the colonial period that are consistent with known effects of mercury intoxication. Conclusions: According to our calculations, between 1564 and 1810, an estimated 17,000 metric tons of mercury vapor were emitted from cinnabar smelting in Huancavelica, and an estimated 39,000 metric tons were released as vapor during silver refining operations in Potosí. Huancavelica and Potosí combined contributed > 25% of the 196,000 metric tons of mercury vapor emissions in all of Latin America between 1500 and 1800. The historical record is laden with evidence of mercury intoxication consistent with effects recognized today. Our estimates serve as the foundation of investigations of present-day contamination in Huancavelica and Potosí resulting from historical emissions of mercury. PMID:22334094

Dissecting a new connection between cytokinin and jasmonic acid in control of leaf growth

USDA-ARS?s Scientific Manuscript database

Plant growth is mediated by two cellular processes: division and elongation. The maize leaf is an excellent model to study plant growth since these processes are spatially separated into discreet zones - a division zone (DZ), transition zone (TZ), and elongation zone (EZ) - at the base of the leaf. ...

The processing of enriched germanium for the Majorana Demonstrator and R&D for a next generation double-beta decay experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abgrall, N.; Arnquist, I. J.; Avignone III, F. T.

The Majorana Demonstrator is an array of point-contact Ge detectors fabricated from Ge isotopically enriched to 88% in 76Ge to search for neutrinoless double beta decay. The processing of Ge for germanium detectors is a well-known technology. However, because of the high cost of Ge enriched in 76Ge special procedures were required to maximize the yield of detector mass and to minimize exposure to cosmic rays. These procedures include careful accounting for the material; shielding it to reduce cosmogenic generation of radioactive isotopes; and development of special reprocessing techniques for contaminated solid germanium, shavings, grindings, acid etchant and cutting fluidsmore » from detector fabrication. Processing procedures were developed that resulted in a total yield in detector mass of 70%. However, none of the acid-etch solution and only 50% of the cutting fluids from detector fabrication were reprocessed. Had they been processed, the projections for the recovery yield would be between 80% and 85%. Maximizing yield is critical to justify a possible future ton-scale experiment. A process for recovery of germanium from the acid-etch solution was developed with yield of about 90%. All material was shielded or stored underground whenever possible to minimize the formation of 68Ge by cosmic rays, which contributes background in the double-beta decay region of interest and cannot be removed by zone refinement and crystal growth. Formation of 68Ge was reduced by a significant factor over that in natural abundance detectors not protected from cosmic rays.« less

The processing of enriched germanium for the Majorana   Demonstrator  and R&D for a next generation double-beta decay experiment

DOE PAGES

Abgrall, N.; Arnquist, I. J.; Avignone III, F. T.; ...

2017-10-07

The Majorana Demonstrator is an array of point-contact Ge detectors fabricated from Ge isotopically enriched to 88% in 76Ge to search for neutrinoless double beta decay. The processing of Ge for germanium detectors is a well-known technology. However, because of the high cost of Ge enriched in 76Ge special procedures were required to maximize the yield of detector mass and to minimize exposure to cosmic rays. These procedures include careful accounting for the material; shielding it to reduce cosmogenic generation of radioactive isotopes; and development of special reprocessing techniques for contaminated solid germanium, shavings, grindings, acid etchant and cutting fluidsmore » from detector fabrication. Processing procedures were developed that resulted in a total yield in detector mass of 70%. However, none of the acid-etch solution and only 50% of the cutting fluids from detector fabrication were reprocessed. Had they been processed, the projections for the recovery yield would be between 80% and 85%. Maximizing yield is critical to justify a possible future ton-scale experiment. A process for recovery of germanium from the acid-etch solution was developed with yield of about 90%. All material was shielded or stored underground whenever possible to minimize the formation of 68Ge by cosmic rays, which contributes background in the double-beta decay region of interest and cannot be removed by zone refinement and crystal growth. Formation of 68Ge was reduced by a significant factor over that in natural abundance detectors not protected from cosmic rays.« less

The processing of enriched germanium for the MAJORANA DEMONSTRATOR and R&D for a next generation double-beta decay experiment

NASA Astrophysics Data System (ADS)

Abgrall, N.; Arnquist, I. J.; Avignone, F. T., III; Barabash, A. S.; Bertrand, F. E.; Bradley, A. W.; Brudanin, V.; Busch, M.; Buuck, M.; Caja, J.; Caja, M.; Caldwell, T. S.; Christofferson, C. D.; Chu, P.-H.; Cuesta, C.; Detwiler, J. A.; Dunagan, C.; Dunstan, D. T.; Efremenko, Yu.; Ejiri, H.; Elliott, S. R.; Gilliss, T.; Giovanetti, G. K.; Goett, J.; Green, M. P.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Haufe, C. R. S.; Henning, R.; Hoppe, E. W.; Jasinski, B. R.; Kidd, M. F.; Konovalov, S. I.; Kouzes, R. T.; Lopez, A. M.; MacMullin, J.; Martin, R. D.; Massarczyk, R.; Meijer, S. J.; Mertens, S.; Meyer, J. H.; Myslik, J.; O'Shaughnessy, C.; Poon, A. W. P.; Radford, D. C.; Rager, J.; Reine, A. L.; Reising, J. A.; Rielage, K.; Robertson, R. G. H.; Shanks, B.; Shirchenko, M.; Suriano, A. M.; Tedeschi, D.; Toth, L. M.; Trimble, J. E.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yu, C.-H.; Yumatov, V.; Zhitnikov, I.; Zhu, B. X.

2018-01-01

The MAJORANA DEMONSTRATOR is an array of point-contact Ge detectors fabricated from Ge isotopically enriched to 88% in 76 Ge to search for neutrinoless double beta decay. The processing of Ge for germanium detectors is a well-known technology. However, because of the high cost of Ge enriched in 76 Ge special procedures were required to maximize the yield of detector mass and to minimize exposure to cosmic rays. These procedures include careful accounting for the material; shielding it to reduce cosmogenic generation of radioactive isotopes; and development of special reprocessing techniques for contaminated solid germanium, shavings, grindings, acid etchant and cutting fluids from detector fabrication. Processing procedures were developed that resulted in a total yield in detector mass of 70%. However, none of the acid-etch solution and only 50% of the cutting fluids from detector fabrication were reprocessed. Had they been processed, the projections for the recovery yield would be between 80% and 85%. Maximizing yield is critical to justify a possible future ton-scale experiment. A process for recovery of germanium from the acid-etch solution was developed with yield of about 90%. All material was shielded or stored underground whenever possible to minimize the formation of 68Ge by cosmic rays, which contributes background in the double-beta decay region of interest and cannot be removed by zone refinement and crystal growth. Formation of 68Ge was reduced by a significant factor over that in natural abundance detectors not protected from cosmic rays.

The processing of enriched germanium for the Majorana Demonstrator and R&D for a next generation double-beta decay experiment

DOE PAGES

Abgrall, N.; Arnquist, I. J.; Avignone III, F. T.; ...

2017-10-07

The Majorana Demonstrator is an array of point-contact Ge detectors fabricated from Ge isotopically enriched to 88% in 76Ge to search for neutrinoless double beta decay. The processing of Ge for germanium detectors is a well-known technology. However, because of the high cost of Ge enriched in 76Ge special procedures were required to maximize the yield of detector mass and to minimize exposure to cosmic rays. These procedures include careful accounting for the material; shielding it to reduce cosmogenic generation of radioactive isotopes; and development of special reprocessing techniques for contaminated solid germanium, shavings, grindings, acid etchant and cutting fluidsmore » from detector fabrication. Processing procedures were developed that resulted in a total yield in detector mass of 70%. However, none of the acid-etch solution and only 50% of the cutting fluids from detector fabrication were reprocessed. Had they been processed, the projections for the recovery yield would be between 80% and 85%. Maximizing yield is critical to justify a possible future ton-scale experiment. A process for recovery of germanium from the acid-etch solution was developed with yield of about 90%. All material was shielded or stored underground whenever possible to minimize the formation of 68Ge by cosmic rays, which contributes background in the double-beta decay region of interest and cannot be removed by zone refinement and crystal growth. Formation of 68Ge was reduced by a significant factor over that in natural abundance detectors not protected from cosmic rays.« less

Survival of bacterial indicators and the functional diversity of native microbial communities in the Floridan aquifer system, south Florida

USGS Publications Warehouse

Lisle, John T.

2014-01-01

The Upper Floridan aquifer in the southern region of Florida is a multi-use, regional scale aquifer that is used as a potable water source and as a repository for passively recharged untreated surface waters, and injected treated surface water and wastewater, industrial wastes, including those which contain greenhouse gases (for example, carbon dioxide). The presence of confined zones within the Floridan aquifer that range in salinity from fresh to brackish allow regulatory agencies to permit the injection of these different types of product waters into specific zones without detrimental effects to humans and terrestrial and aquatic ecosystems. The type of recharge that has received the most regulatory attention in south Florida is aquifer storage and recovery (ASR). The treated water, prior to injection and during recovery, must meet primary and secondary drinking water standards. The primary microbiology drinking water standard is total coliforms, which have been shown to be difficult to inactivate below the regulatory standard during the treatment process at some ASR facilities. The inefficient inactivation of this group of indicator bacteria permits their direct injection into the storage zones of the Floridan aquifer. Prior to this study, the inactivation rates for any member of the total coliform group during exposure to native geochemical conditions in groundwater from any zone of the Floridan aquifer had not been derived. Aboveground flow through mesocosms and diffusion chambers were used to quantify the inactivation rates of two bacterial indicators, Escherichia coli and Pseudomonas aeruginosa, during exposure to groundwater from six wells. These wells collect water from two ASR storage zones: the Upper Floridan aquifer (UFA) and Avon Park Permeable Zone (APPZ). Both bacterial strains followed a biphasic inactivation model. The E. coli populations had slower inactivation rates in the UFA (range: 0.217–0.628 per hour (h-1)) during the first phase of the model than when exposed to groundwater from the APPZ (range: 0.540–0.684 h-1). The inactivation rates for the first phase of the models for P. aeruginosa were not significantly different between the UFA (range: 0.144–0.770 h-1) and APPZ (range: 0.159–0.772 h-1) aquifer zones. The inactivation rates for the second phase of the model for this P. aeruginosa were also similar between UFA (range: 0.003–0.008 h-1) and APPZ (0.004–0.005 h-1) zones, although significantly slower than the model’s first phase rates for this bacterial species. Geochemical data were used to determine which dissimilatory biogeochemical reactions were most likely to occur under the native conditions in the UFA and APPZ zones using thermodynamics principles to calculate free energy yields and other cell-related energetics data. The biogeochemical processes of acetotrophic and hydrogenotrophic sulfate reduction, methanogenesis and anaerobic oxidation of methane dominated in all six groundwater sites. A high throughput DNA microarray sequencing technology was used to characterize the diversity in the native aquifer bacterial communities (bacteria and archaea) and assign putative physiological capabilities to the members of those communities. The bacterial communities in both zones of the aquifer were shown to possess the capabilities for primary and secondary fermentation, acetogenesis, methanogenesis, anaerobic methane oxidation, syntrophy with methanogens, ammonification, and sulfate reduction. The data from this study provide the first determination of bacterial indicator survival during exposure to native geochemical conditions of the Floridan aquifer in south Florida. Additionally, the energetics and functional bacterial diversity characterizations are the first descriptions of native bacterial communities in this region of the Floridan aquifer and reveal how these communities persist under such extreme conditions. Collectively, these types of data can be used to develop and refine groundwater models.

The Critical Zone: A Necessary Framework for Understanding Surface Earth Processes

NASA Astrophysics Data System (ADS)

Dietrich, W. E.

2016-12-01

One definition of the critical zone is: the thin veneer of Earth that extends from the top of the vegetation to the base of weathered bedrock. With this definition we can envision the critical zone as a distinct entity with a well-defined top and a fairly well-defined bottom that is distributed across terrestrial earth landscapes. It is a zone of co-evolving processes and, importantly, much of this zone is well below the soil mantle (and commonly more than 10 times thicker than the soil). Weathering advance into fresh bedrock creates a hydrologically-conductive skin that mediates runoff and solute chemistry, stores water used by vegetation, releases water as baseflow to streams, influences soil production and hillslope evolution, and feeds gasses to the atmosphere. Especially in seasonally dry environments, rock moisture in the critical zone, i.e. moisture that is exchangeable and potentially mobile in the matrix and fractures of the bedrock, can be a significant source of water to plants and is a previously unrecognized large component of the water budget that matters to climate models. First observations on the systematic variation of the critical zone across hillslopes have led to four distinct theories representing four distinct processes for what controls the depth to fresh bedrock (and thus the thickness of this zone across a hillslope). These theories are motivating geophysical surveys, deep drilling, and other actions to parameterize and explore the power of these models. Studies at the NSF-supported Critical Zone Observatories have taught us that the critical zone is an entity and that enduring field studies reveal key processes. A challenge we now face is how to include this emerging understanding of the critical zone into models of reactive transport, hydrologic processes and water supply, critical zone structure, landscape evolution, and climate.

Accurate macromolecular crystallographic refinement: incorporation of the linear scaling, semiempirical quantum-mechanics program DivCon into the PHENIX refinement package.

PubMed

Borbulevych, Oleg Y; Plumley, Joshua A; Martin, Roger I; Merz, Kenneth M; Westerhoff, Lance M

2014-05-01

Macromolecular crystallographic refinement relies on sometimes dubious stereochemical restraints and rudimentary energy functionals to ensure the correct geometry of the model of the macromolecule and any covalently bound ligand(s). The ligand stereochemical restraint file (CIF) requires a priori understanding of the ligand geometry within the active site, and creation of the CIF is often an error-prone process owing to the great variety of potential ligand chemistry and structure. Stereochemical restraints have been replaced with more robust functionals through the integration of the linear-scaling, semiempirical quantum-mechanics (SE-QM) program DivCon with the PHENIX X-ray refinement engine. The PHENIX/DivCon package has been thoroughly validated on a population of 50 protein-ligand Protein Data Bank (PDB) structures with a range of resolutions and chemistry. The PDB structures used for the validation were originally refined utilizing various refinement packages and were published within the past five years. PHENIX/DivCon does not utilize CIF(s), link restraints and other parameters for refinement and hence it does not make as many a priori assumptions about the model. Across the entire population, the method results in reasonable ligand geometries and low ligand strains, even when the original refinement exhibited difficulties, indicating that PHENIX/DivCon is applicable to both single-structure and high-throughput crystallography.

Delineation, peer review, and refinement of subregions of the conterminous United States

Treesearch

J.E. Keys; D.T. Cleland; W.H. McNab

2007-01-01

This paper briefly describes the background of the U.S. Department of Agriculture (USDA) Forest Service National Hierarchical Framework of Ecological Units and the methods used for delineating map units at the subregion planning and analysis scale. The process for scientific review and continuous refinement of ecological units and associated data of subregions is also...

Disk Refining and Ultrasonication Treated Sugarcane Bagasse Residues for Poly(Vinyl Alcohol) Bio-composites

Treesearch

Qingzheng Cheng; Zhaohui Tong; Luisa Dempere; Lonnie Ingram; Letian Wang; J.Y. Zhu

2013-01-01

Disk refining and ultrasonication treated sugarcane bagasse residues reclaimed from the waste stream of a simplified bioethanol process after fermentation were used to fabricate biobased composites with poly(vinyl alcohol) (PVA) by film casting. The morphologies and the size distributions of residue particles were characterized by scanning electronic microscopy and...

Spatial and temporal variability of clouds and precipitation over Germany: multiscale simulations across the "gray zone"

NASA Astrophysics Data System (ADS)

Barthlott, C.; Hoose, C.

2015-11-01

This paper assesses the resolution dependance of clouds and precipitation over Germany by numerical simulations with the COnsortium for Small-scale MOdeling (COSMO) model. Six intensive observation periods of the HOPE (HD(CP)2 Observational Prototype Experiment) measurement campaign conducted in spring 2013 and 1 summer day of the same year are simulated. By means of a series of grid-refinement resolution tests (horizontal grid spacing 2.8, 1 km, 500, and 250 m), the applicability of the COSMO model to represent real weather events in the gray zone, i.e., the scale ranging between the mesoscale limit (no turbulence resolved) and the large-eddy simulation limit (energy-containing turbulence resolved), is tested. To the authors' knowledge, this paper presents the first non-idealized COSMO simulations in the peer-reviewed literature at the 250-500 m scale. It is found that the kinetic energy spectra derived from model output show the expected -5/3 slope, as well as a dependency on model resolution, and that the effective resolution lies between 6 and 7 times the nominal resolution. Although the representation of a number of processes is enhanced with resolution (e.g., boundary-layer thermals, low-level convergence zones, gravity waves), their influence on the temporal evolution of precipitation is rather weak. However, rain intensities vary with resolution, leading to differences in the total rain amount of up to +48 %. Furthermore, the location of rain is similar for the springtime cases with moderate and strong synoptic forcing, whereas significant differences are obtained for the summertime case with air mass convection. Domain-averaged liquid water paths and cloud condensate profiles are used to analyze the temporal and spatial variability of the simulated clouds. Finally, probability density functions of convection-related parameters are analyzed to investigate their dependance on model resolution and their impact on cloud formation and subsequent precipitation.

GWM-2005 - A Groundwater-Management Process for MODFLOW-2005 with Local Grid Refinement (LGR) Capability

USGS Publications Warehouse

Ahlfeld, David P.; Baker, Kristine M.; Barlow, Paul M.

2009-01-01

This report describes the Groundwater-Management (GWM) Process for MODFLOW-2005, the 2005 version of the U.S. Geological Survey modular three-dimensional groundwater model. GWM can solve a broad range of groundwater-management problems by combined use of simulation- and optimization-modeling techniques. These problems include limiting groundwater-level declines or streamflow depletions, managing groundwater withdrawals, and conjunctively using groundwater and surface-water resources. GWM was initially released for the 2000 version of MODFLOW. Several modifications and enhancements have been made to GWM since its initial release to increase the scope of the program's capabilities and to improve its operation and reporting of results. The new code, which is called GWM-2005, also was designed to support the local grid refinement capability of MODFLOW-2005. Local grid refinement allows for the simulation of one or more higher resolution local grids (referred to as child models) within a coarser grid parent model. Local grid refinement is often needed to improve simulation accuracy in regions where hydraulic gradients change substantially over short distances or in areas requiring detailed representation of aquifer heterogeneity. GWM-2005 can be used to formulate and solve groundwater-management problems that include components in both parent and child models. Although local grid refinement increases simulation accuracy, it can also substantially increase simulation run times.

Resource Production on the Moon

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.

2014-01-01

A self-sustaining settlement on the moon, or on other airless bodies such as asteroids, will require the ability to refine desired raw materials from available resources, such as lunar or asteroidal regolith. This work will focus on the example case of pro-duction from lunar regolith. The same process sequences could be used at other locations. Stony asteroids typically have regolith similar to that of the moon, and refining of asteroidal material could use the same techniques, adapted for microgravity. Likewise, Martian rock and soil could also be processed by the techniques discussed here.

Potential of direct metal deposition technology for manufacturing thick functionally graded coatings and parts for reactors components

NASA Astrophysics Data System (ADS)

Thivillon, L.; Bertrand, Ph.; Laget, B.; Smurov, I.

2009-03-01

Direct metal deposition (DMD) is an automated 3D deposition process arising from laser cladding technology with co-axial powder injection to refine or refurbish parts. Recently DMD has been extended to manufacture large-size near-net-shape components. When applied for manufacturing new parts (or their refinement), DMD can provide tailored thermal properties, high corrosion resistance, tailored tribology, multifunctional performance and cost savings due to smart material combinations. In repair (refurbishment) operations, DMD can be applied for parts with a wide variety of geometries and sizes. In contrast to the current tool repair techniques such as tungsten inert gas (TIG), metal inert gas (MIG) and plasma welding, laser cladding technology by DMD offers a well-controlled heat-treated zone due to the high energy density of the laser beam. In addition, this technology may be used for preventative maintenance and design changes/up-grading. One of the advantages of DMD is the possibility to build functionally graded coatings (from 1 mm thickness and higher) and 3D multi-material objects (for example, 100 mm-sized monolithic rectangular) in a single-step manufacturing cycle by using up to 4-channel powder feeder. Approved materials are: Fe (including stainless steel), Ni and Co alloys, (Cu,Ni 10%), WC compounds, TiC compounds. The developed coatings/parts are characterized by low porosity (<1%), fine microstructure, and their microhardness is close to the benchmark value of wrought alloys after thermal treatment (Co-based alloy Stellite, Inox 316L, stainless steel 17-4PH). The intended applications concern cooling elements with complex geometry, friction joints under high temperature and load, light-weight mechanical support structures, hermetic joints, tubes with complex geometry, and tailored inside and outside surface properties, etc.

Geophysical signature of hydration-dehydration processes in active subduction zones

NASA Astrophysics Data System (ADS)

Reynard, Bruno

2013-04-01

Seismological and magneto-telluric tomographies are potential tools for imaging fluid circulation when combined with petrophysical models. Recent measurements of the physical properties of serpentine allow refining hydration of the mantle and fluid circulation in the mantle wedge from geophysical data. In the slab lithospheric mantle, serpentinization caused by bending at the trench is limited to a few kilometers below the oceanic crust (<5 km). Double Wadati-Benioff zones, 20-30 km below the crust, are explained by deformation of dry peridotites, not by serpentine dehydration. It reduces the required amount of water stored in solid phases in the slab (Reynard et al., 2010). In the cold (<700°C) fore-arc mantle wedge above the subducting slab, serpentinization is caused by the release of large amounts of hydrous fluids in the cold mantle above the dehydrating subducted plate. Low seismic velocities in the wedge give a time-integrated estimate of hydration and serpentinization. Serpentinization reaches 50-100% in hot subduction, while it is below 10% in cold subduction (Bezacier et al., 2010; Reynard, 2012). Electromagnetic profiles of the mantle wedge reveal high electrical-conductivity bodies. In hot areas of the mantle wedge (> 700°C), water released by dehydration of the slab induces melting of the mantle under volcanic arcs, explaining the observed high conductivities. In the cold melt-free wedge (< 700°C), high conductivities in electromagnetic profiles provide "instantaneous" images of fluid circulation because the measured electrical conductivity of serpentine is below 0.1 mS/m (Reynard et al., 2011). A small fraction (ca. 1% in volume) of connective high-salinity fluids accounts for the highest observed conductivities. Low-salinity fluids (≤ 0.1 m) released by slab dehydration evolve towards high-salinity (≥ 1 m) fluids during progressive serpentinization in the wedge. These fluids can mix with arc magmas at depths and account for high-chlorine melt inclusions in arc lavas. High electrical conductivities up to 1 S/m in the hydrated wedge of the hot subductions (Ryukyu, Kyushu, Cascadia) reflect high fluid concentration, while low to moderate (<0.01 S/m) conductivities in the cold subductions (N-E Japan, Bolivia) reflect low fluid flow. This is consistent with the seismic observations of extensive shallow serpentinization in hot subduction zones, while serpentinization is sluggish in cold subduction zones. Bezacier, L., et al. 2010. Elasticity of antigorite, seismic detection of serpentinites, and anisotropy in subduction zones. Earth and Planetary Science Letters, 289, 198-208. Reynard, B., 2012. Serpentine in active subduction zones. Lithos, http://dx.doi.org/10.1016/j.lithos.2012.10.012. Reynard, B., Mibe, K. & Van de Moortele, B., 2011. Electrical conductivity of the serpentinised mantle and fluid flow in subduction zones. Earth and Planetary Science Letters, 307, 387-394. Reynard, B., Nakajima, J. & Kawakatsu, H., 2010. Earthquakes and plastic deformation of anhydrous slab mantle in double Wadati-Benioff zones. Geophysical Research Letters, 37, L24309.

Using stable isotopes and major ions to identify hydrological processes and geochemical characteristics in a typical karstic basin, Guizhou, Southwest China.

PubMed

Han, Zhiwei; Tang, Changyuan; Wu, Pan; Zhang, Ruixue; Zhang, Chipeng

2014-01-01

The investigation of hydrological processes is very important for water resource development in karst basins. In order to understand these processes associated with complex hydrogeochemical evolution, a typical basin was chosen in Houzai, southwest China. The basin was hydrogeologically classified into three zones based on hydrogen and oxygen isotopes as well as the field surveys. Isotopic values were found to be enriched in zone 2 where paddy fields were prevailing with well-developed underground flow systems, and heavier than those in zone 1. Zone 3 was considered as the mixture of zones 1 and 2 with isotopic values falling in the range between the two zones. A conceptual hydrological model was thus proposed to reveal the probable hydrological cycle in the basin. In addition, major processes of long-term chemical weathering in the karstic basin were discussed, and reactions between water and carbonate rocks proved to be the main geochemical processes in karst aquifers.

Process-based modeling of temperature and water profiles in the seedling recruitment zone: Part II. Seedling emergence timing

USDA-ARS?s Scientific Manuscript database

Predictions of seedling emergence timing for spring wheat are facilitated by process-based modeling of the microsite environment in the shallow seedling recruitment zone. Hourly temperature and water profiles within the recruitment zone for 60 days after planting were simulated from the process-base...

Revealing the sub-nanometere three-dimensional microscture of a metallic meteorite

NASA Astrophysics Data System (ADS)

Einsle, J. F.; Harrison, R.; Blukis, R.; Eggeman, A.; Saghi, Z.; Martineau, B.; Bagot, P.; Collins, S. M.; Midgley, P. A.

2017-12-01

Coming from from the core of differentiated planetesimals, iron-nickel meteorites provide some of the only direct material artefacts from planetary cores. Iron - nickel meteorites contain a record of their thermal and magnetic history, written in the intergrowth of iron-rich and nickel-rich phases that formed during slow cooling over millions of years. Of intense interest for understanding the thermal and magnetic history is the `'cloudy zone''. This nanoscale intergrowth that has recently been used to provide a record of magnetic activity on the parent body of stony-iron meteorites. The cloudy zone consists of islands of tetrataenite surrounded by a matrix phase, Here we use a multi-scale and multidimensional comparative study using high-resolution electron diffraction, scanning transmission electron tomography with chemical mapping, atom probe tomography and micromagnetic simulations to reveal the three-dimensional architecture of the cloudy zone with sub-nanometre spatial resolution. Machine learning data deconvolution strategies enable the three microanalytical techniques to converge on a consistent microstructural description for the cloudy zone. Isolated islands of tetrataenite are found, embedded in a continuous matrix of an FCC-supercell of Fe27Ni5 structure, never before identified in nature. The tetrataenite islands are arranged in clusters of three crystallographic variants, which control how magnetic information is encoded into the nanostructure during slow cooling. The new compositional, crystallographic and micromagnetic data have profound implications for how the cloudy zone acquires magnetic remanence, and requires a revision of the low-temperature metastable phase diagram of the Fe-Ni system. This can lead to a refinement of core dynamics in small planetoids.

Using supercritical fluids to refine hydrocarbons

DOEpatents

Yarbro, Stephen Lee

2015-06-09

A system and method for reactively refining hydrocarbons, such as heavy oils with API gravities of less than 20 degrees and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure, using a selected fluid at supercritical conditions. A reaction portion of the system and method delivers lightweight, volatile hydrocarbons to an associated contacting unit which operates in mixed subcritical/supercritical or supercritical modes. Using thermal diffusion, multiphase contact, or a momentum generating pressure gradient, the contacting unit separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques.

Hybrid zone studies: An interdisciplinary approach for the analysis of evolutionary processes

USGS Publications Warehouse

Scribner, Kim T.

1994-01-01

There has been considerable debate in the ecological and evolutionary literature over the relative importance and rate by which microevolutionary processes operating at the population level result in separation and differentiation of lineages and populations, and ultimately in speciation. Our understanding of evolutionary processes have need greatly enhances through the study of hybridization and hybrid zones. Indeed, hybrid zones have been described as “natural laboratories” (Barton, N. H., and G .M. Hewitt, 189. Adaptation, speciation, and hybrid zones. Nature 341:497-503) or as “windows on the evolutionary processes” (Harrison, R. G. 1990. Hybrid zones: windows on the evolutionary process. Oxford Surveys in Evolutionary Biology 7:69-128). Hybrid zones greatly facilitate analyses of evolutionary dynamics because differences in factors such as mating preference, fertility, and viability are likely to be magnified, making the consequences easier to document over short periods of time.

75 FR 64248 - Approval for Processing Authority Foreign-Trade Zones 73 and 74; The Belt's Corporation (Kitting...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [Order No. 1713] Approval for Processing Authority Foreign-Trade Zones 73 and 74; The Belt's Corporation (Kitting of Liquor Gift Sets), Elkridge and Baltimore, MD Pursuant to its authority under the Foreign-Trade Zones Act of June 18, 1934, as amended (19 U...

Comparison of Antioxidant Properties of Refined and Whole Wheat Flour and Bread

PubMed Central

Yu, Lilei; Nanguet, Anne-Laure; Beta, Trust

2013-01-01

Antioxidant properties of refined and whole wheat flour and their resultant bread were investigated to document the effects of baking. Total phenolic content (TPC), 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity and oxygen radical absorbance capacity (ORAC) were employed to determine the content of ethanol extractable phenolic compounds. HPLC was used to detect the presence of phenolic acids prior to their confirmation using LC-MS/MS. Whole wheat flour showed significantly higher antioxidant activity than refined flour (p < 0.05). There was a significant effect of the bread-making process with the TPC of whole wheat bread (1.50–1.65 mg/g) and white bread (0.79–1.03 mg/g) showing a respective reduction of 28% and 33% of the levels found in whole wheat and refined flour. Similarly, baking decreased DPPH radical scavenging capacity by 32% and 30%. ORAC values, however, indicated that baking increased the antioxidant activities of whole wheat and refined flour by 1.8 and 2.9 times, respectively. HPLC analysis showed an increase of 18% to 35% in ferulic acid after baking to obtain whole and refined wheat bread containing 330.1 and 25.3 µg/g (average), respectively. Whole wheat flour and bread were superior to refined flour and bread in in vitro antioxidant properties. PMID:26784470

Modeling of dispersed-drug delivery from planar polymeric systems: optimizing analytical solutions.

PubMed

Helbling, Ignacio M; Ibarra, Juan C D; Luna, Julio A; Cabrera, María I; Grau, Ricardo J A

2010-11-15

Analytical solutions for the case of controlled dispersed-drug release from planar non-erodible polymeric matrices, based on Refined Integral Method, are presented. A new adjusting equation is used for the dissolved drug concentration profile in the depletion zone. The set of equations match the available exact solution. In order to illustrate the usefulness of this model, comparisons with experimental profiles reported in the literature are presented. The obtained results show that the model can be employed in a broad range of applicability. Copyright © 2010 Elsevier B.V. All rights reserved.

Chemical and physical aspects of refining coal liquids

NASA Astrophysics Data System (ADS)

Shah, Y. T.; Stiegel, G. J.; Krishnamurthy, S.

1981-02-01

Increasing costs and declining reserves of petroleum are forcing oil importing countries to develop alternate energy sources. The direct liquefaction of coal is currently being investigated as a viable means of producing substitute liquid fuels. The coal liquids derived from such processes are typically high in nitrogen, oxygen and sulfur besides having a high aromatic and metals content. It is therefore envisaged that modifications to existing petroleum refining technology will be necessary in order to economically upgrade coal liquids. In this review, compositional data for various coal liquids are presented and compared with those for petroleum fuels. Studies reported on the stability of coal liquids are discussed. The feasibility of processing blends of coal liquids with petroleum feedstocks in existing refineries is evaluated. The chemistry of hydroprocessing is discussed through kinetic and mechanistic studies using compounds which are commonly detected in coal liquids. The pros and cons of using conventional petroleum refining catalysts for upgrading coal liquids are discussed.

Refined Simulation of Satellite Laser Altimeter Full Echo Waveform

NASA Astrophysics Data System (ADS)

Men, H.; Xing, Y.; Li, G.; Gao, X.; Zhao, Y.; Gao, X.

2018-04-01

The return waveform of satellite laser altimeter plays vital role in the satellite parameters designation, data processing and application. In this paper, a method of refined full waveform simulation is proposed based on the reflectivity of the ground target, the true emission waveform and the Laser Profile Array (LPA). The ICESat/GLAS data is used as the validation data. Finally, we evaluated the simulation accuracy with the correlation coefficient. It was found that the accuracy of echo simulation could be significantly improved by considering the reflectivity of the ground target and the emission waveform. However, the laser intensity distribution recorded by the LPA has little effect on the echo simulation accuracy when compared with the distribution of the simulated laser energy. At last, we proposed a refinement idea by analyzing the experimental results, in the hope of providing references for the waveform data simulation and processing of GF-7 satellite in the future.

Reactor Meltdown: Critical Zone Processes In Siliciclastics Unlikely To Be Directly Transferable To Carbonates

NASA Astrophysics Data System (ADS)

Gulley, J. D.; Cohen, M. J.; Kramer, M. G.; Martin, J. B.; Graham, W. D.

2013-12-01

Carbonate terrains cover 20% of Earth's ice-free land and are modified through interactions between rocks, water and biota that couple ecosystems processes to weathering reactions within the critical zone. Weathering in carbonate systems differs from the Critical Zone Reactor model developed for siliciclastic systems because reactions in siliciclastic critical zones largely consist of incongruent weathering (e.g., feldspar to secondary clay minerals) that typically occur in the soil zone within a few meters of the land surface. These incongruent reactions create regolith, which is removed by physical transport mechanisms that drive landscape denudation. In contrast, carbonate critical zones are mostly composed of homogeneous and soluble minerals, which dissolve congruently with the weathering products exported in solution, limiting regolith in the soil mantle to small amounts of insoluble residues. These reactions can extend to depths greater than 2 km below the surface. As water at the land surface drains preferentially through vertical joints and horizontal bedding planes of the carbonate critical zones, it is 'charged' with biologically-derived carbon dioxide, which decreases pH, dissolves carbonate rock, and enlarges subsurface flowpaths through feedbacks between flow and dissolution. Caves are extreme end products of this process and are key morphological features of carbonate critical zones. Caves link surface processes to the deep subsurface and serve as efficient delivery agents for oxygen, carbon and nutrients to zones within the critical zone that are deficient in all three, interrupting vertical and horizontal chemical gradients that would exist if caves were not present. We present select data from air and water-filled caves in the upper Floridan aquifer, Florida, USA, that demonstrate how caves, acting as very large preferential flow paths, alter processes in carbonate relative to siliciclastic critical zones. While caves represent an extreme end member of hydraulic and chemical heterogeneity that has no direct counterpart siliciclastic systems, these large voids provide easily accessible laboratories to investigate processes in carbonate critical zones, and how they differ from standard siliciclastic models of critical zones.

Merging Hydrologic, Geochemical, and Geophysical Approaches to Understand the Regolith Architecture of a Deeply Weathered Piedmont Critical Zone

NASA Astrophysics Data System (ADS)

Cosans, C.; Moore, J.; Harman, C. J.

2017-12-01

Located in the deeply weathered Piedmont in Maryland, Pond Branch has a rich legacy of hydrological and geochemical research dating back to the first geochemical mass balance study published in 1970. More recently, geophysical investigations including seismic and electrical resistivity tomography have characterized the subsurface at Pond Branch and contributed to new hypotheses about critical zone evolution. Heterogeneity in electrical resistivity in the shallow subsurface may suggest disparate flow paths for recharge, with some regions with low hydraulic conductivity generating perched flow, while other hillslope sections recharge to the much deeper regolith boundary. These shallow and deep flow paths are hypothesized to be somewhat hydrologically and chemically connected, with the spatially and temporally discontinuous connections resulting in different hydraulic responses to recharge and different concentrations of weathering solutes. To test this hypothesis, we combined modeling and field approaches. We modeled weathering solutes along the hypothesized flow paths using PFLOTRAN. We measured hydrologic gradients in the hillslopes and riparian zone using piezometer water levels. We collected geochemical data including major ions and silica. Weathering solute concentrations were measured directly in the precipitation, hillslope springs, and the riparian zone for comparison to modeled concentration values. End member mixing methods were used to determine contributions of precipitation, hillslopes, and riparian zone to the stream. Combining geophysical, geochemical, and hydrological methods may offer insights into the source of stream water and controls on chemical weathering. Previous hypotheses that Piedmont critical zone architecture results from a balance of erosion, soil, and weathering front advance rates cannot account for the inverted regolith structure observed through seismic investigations at Pond Branch. Recent alternative hypotheses including weathering along tectonically-induced fractures and weathering front advance have been proposed, but additional data are needed to test them. Developing a thorough, nuanced understanding of the geochemical and hydrological behavior of Pond Branch may help test and refine hypotheses for Piedmont critical zone evolution.

Acute, subchronic, and developmental toxicological properties of lubricating oil base stocks.

PubMed

Dalbey, Walden E; McKee, Richard H; Goyak, Katy Olsavsky; Biles, Robert W; Murray, Jay; White, Russell

2014-01-01

Lubricating oil base stocks (LOBs) are substances used in the manufacture of finished lubricants and greases. They are produced from residue remaining after atmospheric distillation of crude oil that is subsequently fractionated by vacuum distillation and additional refining steps. Initial LOB streams that have been produced by vacuum distillation but not further refined may contain polycyclic aromatic compounds (PACs) and may present carcinogenic hazards. In modern refineries, LOBs are further refined by multistep processes including solvent extraction and/or hydrogen treatment to reduce the levels of PACs and other undesirable constituents. Thus, mildly (insufficiently) refined LOBs are potentially more hazardous than more severely (sufficiently) refined LOBs. This article discusses the evaluation of LOBs using statistical models based on content of PACs; these models indicate that insufficiently refined LOBs (potentially carcinogenic LOBs) can also produce systemic and developmental effects with repeated dermal exposure. Experimental data were also obtained in ten 13-week dermal studies in rats, eight 4-week dermal studies in rabbits, and seven dermal developmental toxicity studies with sufficiently refined LOBs (noncarcinogenic and commonly marketed) in which no observed adverse effect levels for systemic toxicity and developmental toxicity were 1000 to 2000 mg/kg/d with dermal exposures, typically the highest dose tested. Results in both oral and inhalation developmental toxicity studies were similar. This absence of toxicologically relevant findings was consistent with lower PAC content of sufficiently refined LOBs. Based on data on reproductive organs with repeated dosing and parameters in developmental toxicity studies, sufficiently refined LOBs are likely to have little, if any, effect on reproductive parameters.

Improved ethanol yield and reduced Minimum Ethanol Selling Price (MESP) by modifying low severity dilute acid pretreatment with deacetylation and mechanical refining: 1) Experimental

PubMed Central

2012-01-01

Background Historically, acid pretreatment technology for the production of bio-ethanol from corn stover has required severe conditions to overcome biomass recalcitrance. However, the high usage of acid and steam at severe pretreatment conditions hinders the economic feasibility of the ethanol production from biomass. In addition, the amount of acetate and furfural produced during harsh pretreatment is in the range that strongly inhibits cell growth and impedes ethanol fermentation. The current work addresses these issues through pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. Results The results showed that deacetylation with 0.1 M NaOH before acid pretreatment improved the monomeric xylose yield in pretreatment by up to 20% while keeping the furfural yield under 2%. Deacetylation also improved the glucose yield by 10% and the xylose yield by 20% during low solids enzymatic hydrolysis. Mechanical refining using a PFI mill further improved sugar yields during both low- and high-solids enzymatic hydrolysis. Mechanical refining also allowed enzyme loadings to be reduced while maintaining high yields. Deacetylation and mechanical refining are shown to assist in achieving 90% cellulose yield in high-solids (20%) enzymatic hydrolysis. When fermentations were performed under pH control to evaluate the effect of deacetylation and mechanical refining on the ethanol yields, glucose and xylose utilizations over 90% and ethanol yields over 90% were achieved. Overall ethanol yields were calculated based on experimental results for the base case and modified cases. One modified case that integrated deacetylation, mechanical refining, and washing was estimated to produce 88 gallons of ethanol per ton of biomass. Conclusion The current work developed a novel bio-ethanol process that features pretreatment with lower acid concentrations and temperatures incorporated with deacetylation and mechanical refining. The new process shows improved overall ethanol yields compared to traditional dilute acid pretreatment. The experimental results from this work support the techno-economic analysis and calculation of Minimum Ethanol Selling Price (MESP) detailed in our companion paper. PMID:22888758

Imaging Inelastic Fracture Processes in Biomimetic Nanocomposites and Nacre by Laser Speckle for Better Toughness.

PubMed

Verho, Tuukka; Karppinen, Pasi; Gröschel, André H; Ikkala, Olli

2018-01-01

Mollusk nacre is a prototypical biological inorganic-organic composite that combines high toughness, stiffness, and strength by its brick-and-mortar microstructure, which has inspired several synthetic mimics. Its remarkable fracture toughness relies on inelastic deformations at the process zone at the crack tip that dissolve stress concentrations and stop cracks. The micrometer-scale structure allows resolving the size and shape of the process zone to understand the fracture processes. However, for better scalability, nacre-mimetic nanocomposites with aligned inorganic or graphene nanosheets are extensively pursued, to avoid the packing problems of mesoscale sheets like in nacre or slow in situ biomineralization. This calls for novel methods to explore the process zone of biomimetic nanocomposites. Here the fracture of nacre and nacre-inspired clay/polymer nanocomposite is explored using laser speckle imaging that reveals the process zone even in absence of changes in optical scattering. To demonstrate the diagnostic value, compared to nacre, the nacre-inspired nanocomposite develops a process zone more abruptly with macroscopic crack deflection shown by a flattened process zone. In situ scanning electron microscopy suggests similar toughening mechanisms in nanocomposite and nacre. These new insights guide the design of nacre-inspired nanocomposites toward better mechanical properties to reach the level of synergy of their biological model.

The influence of surface-active agents in gas mixture on the intensity of jet condensation

NASA Astrophysics Data System (ADS)

Yezhov, YV; Okhotin, VS

2017-11-01

The report presents: the methodology of calculation of contact condensation of steam from the steam-gas mixture into the stream of water, taking into account: the mass flow of steam through the boundary phase, particularly the change in turbulent transport properties near the interface and their connection to the interface perturbations due to the surface tension of the mixture; the method of calculation of the surface tension at the interface water - a mixture of fluorocarbon vapor and water, based on the previously established analytical methods we calculate the surface tension for simple one - component liquid-vapor systems. The obtained analytical relation to calculate the surface tension of the mixture is a function of temperature and volume concentration of the fluorocarbon gas in the mixture and is true for all sizes of gas molecules. On the newly created experimental stand is made verification of experimental studies to determine the surface tension of pure substances: water, steam, C3F8 pair C3F8, produced the first experimental data on surface tension at the water - a mixture of water vapor and fluorocarbon C3F8. The obtained experimental data allow us to refine the values of the two constants used in the calculated model of the surface tension of the mixture. Experimental study of jet condensation was carried out with the flow in the zone of condensation of different gases. The condensation process was monitored by measurement of consumption of water flowing from the nozzle, and the formed condensate. When submitting C3F8, there was a noticeable, intensification condensation process compared with the condensation of pure water vapor. The calculation results are in satisfactory agreement with the experimental data on surface tension of the mixture and steam condensation from steam-gas mixture. Analysis of calculation results shows that the presence of surfactants in the condensation zone affects the partial vapor pressure on the interfacial surface, and the thermal conductivity of the liquid jet. The first circumstance leads to deterioration of the condensation process, the second to the intensification of this process. There is obviously an optimum value of concentration of the additive surfactants to the vapour when the condensation process is maximum. According to the developed design methodology contact condensation can evaluate these optimum conditions, their practical effect in the field study.

Uncertainty quantification for complex systems with very high dimensional response using Grassmann manifold variations

NASA Astrophysics Data System (ADS)

Giovanis, D. G.; Shields, M. D.

2018-07-01

This paper addresses uncertainty quantification (UQ) for problems where scalar (or low-dimensional vector) response quantities are insufficient and, instead, full-field (very high-dimensional) responses are of interest. To do so, an adaptive stochastic simulation-based methodology is introduced that refines the probability space based on Grassmann manifold variations. The proposed method has a multi-element character discretizing the probability space into simplex elements using a Delaunay triangulation. For every simplex, the high-dimensional solutions corresponding to its vertices (sample points) are projected onto the Grassmann manifold. The pairwise distances between these points are calculated using appropriately defined metrics and the elements with large total distance are sub-sampled and refined. As a result, regions of the probability space that produce significant changes in the full-field solution are accurately resolved. An added benefit is that an approximation of the solution within each element can be obtained by interpolation on the Grassmann manifold. The method is applied to study the probability of shear band formation in a bulk metallic glass using the shear transformation zone theory.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, X., E-mail: Xiujuan.jiang@pnnl.gov

Soft magnetic materials are often limited in scalability due to conventional processes that do not retain beneficial microstructures, and their associated physical properties, during densification. In this work, friction consolidation (FC) has been studied to fabricate Fe−Si soft magnetic materials from gas-atomized powder precursors. Fe−Si powder is consolidated using variable pressure and tool rotation speed in an effort to evaluate this unique densification approach for potential improvements in magnetic properties. FC, due to the high shear deformation involved, is shown to result in uniform gradual grain structure refinement across the consolidated workpiece from the center nearest the tool to themore » edge. Magnetic properties along different orientations indicate little, if any, textural orientation in the refined grain structure. The effect of annealing on the magnetic properties is evaluated and shown to decrease coercivity. FC processing was able to retain the magnetization of the original gas-atomized powders but further process optimization is needed to reach the optimal coercivity for the soft magnetic materials applications. - Highlights: •Friction stir processing was utilized to consolidate Fe−Si soft magnetic powders. •The resultant microstructure and magnetic properties were correlated to the processing conditions. •Friction consolidation refined the grain size of the materials by ~ 40%. •Annealing successfully reduced the coercivity induced by the stress during processing. •The results shine light on the possible scaling up of nanostructured materials.« less

Growth Oscillatory Zoning in Erythrite, Ideally Co3(AsO4)2·8H2O: Structural Variations in Vivianite-Group Minerals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antao, Sytle M.; Dhaliwal, Inayat

The crystal structure of an oscillatory zoned erythrite sample from Aghbar mine, Bou Azzer, Morocco, was refined using synchrotron high-resolution powder X-ray diffraction (HRPXRD) data, Rietveld refinement, space group C2/m, and Z = 2. The crystal contains two sets of oscillatory zones that appear to have developed during epitaxial growth. The unit-cell parameters obtained are a = 10.24799(3) Å, b = 13.42490(7) Å, c = 4.755885(8) Å, β = 105.1116(3)°, and V = 631.680(4) Å3. The empirical formula for erythrite, obtained with electron-probe micro-analysis (EPMA), is [Co2.78Zn0.11Ni0.07Fe0.04]Σ3.00(AsO4)2·8H2O. Erythrite belongs to the vivianite-type structure that contains M1O2(H2O)4 octahedra and M22O6(H2O)4 octahedralmore » dimers that are linked by TO4 (T5+ = As or P) tetrahedra to form complex layers parallel to the (010) plane. These layers are connected by hydrogen bonds. The average [6] = 2.122(1) Å and average [6] = 2.088(1) Å. With space group C2/m, there are two solid solutions: M3(AsO4)2·8H2O and M3(PO4)2·8H2O where M2+ = Mg, Fe, Co, Ni, or Zn. In these As- and P-series, using data from this study and from the literature, we find that their structural parameters evolve linearly with V and in a nearly parallel manner despite of the large difference in size between P5+ (0.170 Å) and As5+ (0.355 Å) cations. Average [4], [6], and [6] distances increase linearly with V. The average distance is affected by M atoms, whereas the average distance is unaffected because it contains shorter and stronger P–O bonds. Although As- and P-series occur naturally, there is no structural reason why similar V-series vivianite-group minerals do not occur naturally or cannot be synthesized.« less

Refined sugar intake in Australian children.

PubMed

Somerset, Shawn M

2003-12-01

To estimate the intake of refined sugar in Australian children and adolescents, aged 2-18 years. Foods contributing to total sugar intake were identified using data from the National Nutrition Survey 1995 (NNS95), the most recent national dietary survey of the Australian population. The top 100 foods represented means of 85% (range 79-91%) and 82% (range 78-85%) of total sugar intake for boys and girls, respectively. Using published Australian food composition data (NUTTAB95), the proportion of total sugar being refined sugar was estimated for each food. Where published food composition data were not available, calculations from ingredients and manufacturer's information were used. The NNS95 assessed the dietary intake of a random sample of the Australian population, aged 2-18 years (n=3007). Mean daily intakes of refined sugar ranged from 26.9 to 78.3 g for 2-18-year-old girls, representing 6.6-14.8% of total energy intake. Corresponding figures for boys were 27.0 to 81.6 g and 8.0-14.0%, respectively. Of the 10 highest sources of refined sugar for each age group, sweetened beverages, especially cola-type beverages, were the most prominent. Refined sugar is an important contributor to dietary energy in Australian children. Sweetened beverages such as soft drinks and cordials were substantial sources of refined sugar and represent a potential target for campaigns to reduce refined sugar intake. Better access to information on the amounts of sugar added to processed food is essential for appropriate monitoring of this important energy source.

Effect of Solutes on Grain Refinement of As-Cast Fe-4Si Alloy

NASA Astrophysics Data System (ADS)

Li, Ming; Li, Jian-Min; Zheng, Qing; Wang, Geoff; Zhang, Ming-Xing

2018-06-01

Grain size is one of the key microstructural factors that control the mechanical properties of steels. The present work aims to extend the theories of grain refinement which were established for cast light alloys to steel systems. Using a designed Fe-4 wt pct Si alloy (all-ferrite structure during whole solidification process), the solute effect on grain refinement/grain coarsening in ferritic systems was comprehensively investigated. Experimental results showed that boron (B), which is associated with the highest Q value (growth restriction factor) in ferrite, significantly refined the as-cast structure of the Fe-4 wt pct Si alloy. Cu and Mo with low Q values had no effect on grain refinement. However, although Y and Zr have relatively high Q values, addition of these two solutes led to grain coarsening in the Fe-4Si alloy. Understanding the results in regards to the growth restriction factor and the driving force for the solidification led to the conclusion that in addition to the grain growth restriction effect, the changes of thermodynamic driving force for solidification due to the solute addition also played a key role in grain refinement in ferritic alloys.

Effect of Solutes on Grain Refinement of As-Cast Fe-4Si Alloy

NASA Astrophysics Data System (ADS)

Li, Ming; Li, Jian-Min; Zheng, Qing; Wang, Geoff; Zhang, Ming-Xing

2018-03-01

Grain size is one of the key microstructural factors that control the mechanical properties of steels. The present work aims to extend the theories of grain refinement which were established for cast light alloys to steel systems. Using a designed Fe-4 wt pct Si alloy (all-ferrite structure during whole solidification process), the solute effect on grain refinement/grain coarsening in ferritic systems was comprehensively investigated. Experimental results showed that boron (B), which is associated with the highest Q value (growth restriction factor) in ferrite, significantly refined the as-cast structure of the Fe-4 wt pct Si alloy. Cu and Mo with low Q values had no effect on grain refinement. However, although Y and Zr have relatively high Q values, addition of these two solutes led to grain coarsening in the Fe-4Si alloy. Understanding the results in regards to the growth restriction factor and the driving force for the solidification led to the conclusion that in addition to the grain growth restriction effect, the changes of thermodynamic driving force for solidification due to the solute addition also played a key role in grain refinement in ferritic alloys.

A Comparison of Spectral Element and Finite Difference Methods Using Statically Refined Nonconforming Grids for the MHD Island Coalescence Instability Problem

NASA Astrophysics Data System (ADS)

Ng, C. S.; Rosenberg, D.; Pouquet, A.; Germaschewski, K.; Bhattacharjee, A.

2009-04-01

A recently developed spectral-element adaptive refinement incompressible magnetohydrodynamic (MHD) code [Rosenberg, Fournier, Fischer, Pouquet, J. Comp. Phys. 215, 59-80 (2006)] is applied to simulate the problem of MHD island coalescence instability (\\ci) in two dimensions. \\ci is a fundamental MHD process that can produce sharp current layers and subsequent reconnection and heating in a high-Lundquist number plasma such as the solar corona [Ng and Bhattacharjee, Phys. Plasmas, 5, 4028 (1998)]. Due to the formation of thin current layers, it is highly desirable to use adaptively or statically refined grids to resolve them, and to maintain accuracy at the same time. The output of the spectral-element static adaptive refinement simulations are compared with simulations using a finite difference method on the same refinement grids, and both methods are compared to pseudo-spectral simulations with uniform grids as baselines. It is shown that with the statically refined grids roughly scaling linearly with effective resolution, spectral element runs can maintain accuracy significantly higher than that of the finite difference runs, in some cases achieving close to full spectral accuracy.

Coal liquefaction process

DOEpatents

Maa, Peter S.

1978-01-01

A process for liquefying a particulate coal feed to produce useful petroleum-like liquid products which comprises contacting; in a series of two or more coal liquefaction zones, or stages, graded with respect to temperature, an admixture of a polar compound; or compounds, a hydrogen donor solvent and particulate coal, the total effluent being passed in each instance from a low temperature zone, or stage to the next succeeding higher temperature zone, or stage, of the series. The temperature within the initial zone, or stage, of the series is maintained about 70.degree. F and 750.degree. F and the temperature within the final zone, or stage, is maintained between about 750.degree. F and 950.degree. F. The residence time within the first zone, or stage, ranges, generally, from about 20 to about 150 minutes and residence time within each of the remaining zones, or stages, of the series ranges, generally, from about 10 minutes to about 70 minutes. Further steps of the process include: separating the product from the liquefaction zone into fractions inclusive of a liquid solvent fraction; hydrotreating said liquid solvent fraction in a hydrogenation zone; and recycling the hydrogenated liquid solvent mixture to said coal liquefaction zones.

Reduction of Defects in Germanium-Silicon

NASA Technical Reports Server (NTRS)

2003-01-01

Crystals grown without contact with a container have far superior quality to otherwise similar crystals grown in direct contact with a container. In addition to float-zone processing, detached- Bridgman growth is a promising tool to improve crystal quality, without the limitations of float zoning or the defects introduced by normal Bridgman growth. Goals of this project include the development of the detached Bridgman process to be reproducible and well understood and to quantitatively compare the defect and impurity levels in crystals grown by these three methods. Germanium (Ge) and germanium-silicon (Ge-Si) alloys are being used. At MSFC, we are responsible for the detached Bridgman experiments intended to differentiate among proposed mechanisms of detachment, and to confirm or refine our understanding of detachment. Because the contact angle is critical to determining the conditions for detachment, the sessile drop method was used to measure the contact angles as a function of temperature and composition for a large number of substrates made of potential ampoule materials. Growth experiments have used pyrolytic boron nitride (pBN) and fused silica ampoules with the majority of the detached results occurring predictably in the pBN. Etch pit density (EPD) measurements of normal and detached Bridgman-grown Ge samples show a two order of magnitude improvement in the detached-grown samples. The nature and extent of detachment is determined by using profilometry in conjunction with optical and electron microscopy. The stability of detachment has been analyzed, and an empirical model for the conditions necessary to achieve sufficient stability to maintain detached growth for extended periods has been developed. We have investigated the effects on detachment of ampoule material, pressure difference above and below the melt, and Si concentration; samples that are nearly completely detached can be grown repeatedly in pBN. Current work is concentrated on developing a method to make in situ pressure measurements in the growth ampoules.

Numerical investigation of melting and solidification processes in modified surface layers of metal at induction heating

NASA Astrophysics Data System (ADS)

Shchukin, V. G.; Popov, V. N.

2017-10-01

One of the perspective ways to improve the operational properties of parts of machines during induction treatment of their surfaces is the modification of the melt by specially prepared nanoscale particles of refractory compounds (carbides, nitrides, carbonitrides, etc.). This approach allows us to increase the number of crystallization centers and to refine the structural components of the solidified metal. The resulting high dispersity and homogeneity of crystalline grains favorably affect the quality of the treated surfaces. 3D numerical simulation of thermophysical processes in the modification of the surface layer of metal in a moving substrate was carried out. It is assumed that the surface of the substrate is covered with a layer of specially prepared nanoscale particles of a refractory compound, which, upon penetration into the melt, are uniformly distributed in it. The possibility of applying a high-frequency electromagnetic field of high power for heating and melting of a metal (iron) for the purpose of its subsequent modification is investigated. The distribution of electromagnetic energy in the metal is described by empirical formulas. Melting of the metal is considered in the Stefan approximation, and upon solidification it is assumed that all nanoparticles serve as centers for volume-sequential crystallization. Calculations were carried out with the following parameters: specific power p0 = 35 and 40 kW/cm2 at frequency f = 440 and 1200 kHz, the substrate velocity V = 0.5-2.5 cm/s, the nanoparticles' size is 50 nm and concentration Np = 2.0 . 109 cm-3. Based on the results obtained in a quasi-stationary formulation, the distribution of the temperature field, the dimensions of the melting and crystallization zones, the change in the solid fraction in the two-phase zone, the area of the treated substrate surface, depending on the speed of its movement and induction heating characteristics were estimated.

High Resolution Shear-Wave Velocity Structure of Greenland from Surface Wave Analysis

NASA Astrophysics Data System (ADS)

Pourpoint, M.; Anandakrishnan, S.; Ammon, C. J.

2016-12-01

We present a high resolution seismic tomography model of Greenland's lithosphere from the analysis of fundamental mode Rayleigh-wave group velocity dispersion measurements. Regional and teleseismic events recorded by the GLISN, GSN and CN seismic networks over the last 20 years were used. In order to better constrain the crustal structure of Greenland, we also collected and processed several years of ambient noise data. We developed a new group velocity correction method that helps to alleviate the limitations of the sparse Greenland station network and the relatively few local events. The global dispersion model GDM52 from Ekström [2011] was used to calculate group delays from the earthquake to the boundaries of our study area. An iterative reweighted generalized least-square approach was used to invert for the group velocity maps between periods of 5 s and 180 s. A Markov chain Monte Carlo technique was then applied to invert for a 3-D shear wave velocity model of Greenland up to a depth of 200 km and estimate the uncertainties in the model. Our method results in relatively uniform azimuthal coverage and high resolution length ( 200 to 400 km) in west and east Greenland. We detect a deep high velocity zone extending from northwestern to southwestern Greenland and a low velocity zone (LVZ) between central-eastern and northeastern Greenland. The location of the LVZ correlates well with a previously measured high geothermal heat flux and could provide valuable information about its source. We expect the results of the ambient noise tomography to cross-validate the earthquake tomography results and give us a better estimate of the spatial extent and amplitude of the LVZ at shallow depths. A refined regional model of Greenland's lithospheric structure should eventually help better understand how underlying geological and geophysical processes may impact the dynamics of the ice sheet and influence its potential contribution to future sea level changes.

Bauxite Mining and Alumina Refining

PubMed Central

Frisch, Neale; Olney, David

2014-01-01

Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. Conclusions: A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures. PMID:24806720

Developing and Modifying Behavioral Coding Schemes in Pediatric Psychology: A Practical Guide

PubMed Central

McMurtry, C. Meghan; Chambers, Christine T.; Bakeman, Roger

2015-01-01

Objectives To provide a concise and practical guide to the development, modification, and use of behavioral coding schemes for observational data in pediatric psychology. Methods This article provides a review of relevant literature and experience in developing and refining behavioral coding schemes. Results A step-by-step guide to developing and/or modifying behavioral coding schemes is provided. Major steps include refining a research question, developing or refining the coding manual, piloting and refining the coding manual, and implementing the coding scheme. Major tasks within each step are discussed, and pediatric psychology examples are provided throughout. Conclusions Behavioral coding can be a complex and time-intensive process, but the approach is invaluable in allowing researchers to address clinically relevant research questions in ways that would not otherwise be possible. PMID:25416837

30 CFR 285.647 - How will my GAP be processed for Federal consistency under the Coastal Zone Management Act?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will my GAP be processed for Federal consistency under the Coastal Zone Management Act? 285.647 Section 285.647 Mineral Resources MINERALS... Activities Plan § 285.647 How will my GAP be processed for Federal consistency under the Coastal Zone...

30 CFR 285.612 - How will my SAP be processed for Federal consistency under the Coastal Zone Management Act?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will my SAP be processed for Federal consistency under the Coastal Zone Management Act? 285.612 Section 285.612 Mineral Resources MINERALS... Plan § 285.612 How will my SAP be processed for Federal consistency under the Coastal Zone Management...

Three-dimensional landing zone ladar

NASA Astrophysics Data System (ADS)

Savage, James; Goodrich, Shawn; Burns, H. N.

2016-05-01

Three-Dimensional Landing Zone (3D-LZ) refers to a series of Air Force Research Laboratory (AFRL) programs to develop high-resolution, imaging ladar to address helicopter approach and landing in degraded visual environments with emphasis on brownout; cable warning and obstacle avoidance; and controlled flight into terrain. Initial efforts adapted ladar systems built for munition seekers, and success led to a the 3D-LZ Joint Capability Technology Demonstration (JCTD) , a 27-month program to develop and demonstrate a ladar subsystem that could be housed with the AN/AAQ-29 FLIR turret flown on US Air Force Combat Search and Rescue (CSAR) HH-60G Pave Hawk helicopters. Following the JCTD flight demonstration, further development focused on reducing size, weight, and power while continuing to refine the real-time geo-referencing, dust rejection, obstacle and cable avoidance, and Helicopter Terrain Awareness and Warning (HTAWS) capability demonstrated under the JCTD. This paper summarizes significant ladar technology development milestones to date, individual LADAR technologies within 3D-LZ, and results of the flight testing.

Improving Keyhole Stability by External Magnetic Field in Full Penetration Laser Welding

NASA Astrophysics Data System (ADS)

Li, Min; Xu, Jiajun; Huang, Yu; Rong, Youmin

2018-05-01

An external magnetic field was used to improve the keyhole stability in full penetration laser welding 316L steel. The increase of magnetic field strength gave rise to a shorter flying time of the spatter, a weaker size and brightness of the spatter, and a larger spreading area of vapor plume. This suggested that the dynamic behavior of the keyhole was stabilized by the external magnetic field. In addition, a stronger magnetic field could result in a more homogeneous distribution of laser energy, which increased the width of the weld zone, and the height of the bottom weld zone from 381 μm (0 mT) to 605 μm (50 mT). Dendrite and cellular crystal near the weld center disappeared, and grain size was refined. The external magnetic field was beneficial to the keyhole stability and improved the joint quality, because the weld pool was stirred by a Lorentz force resulting from the coupling effect of the magnetic field and inner thermocurrent.

Is Analytic Information Processing a Feature of Expertise in Medicine?

ERIC Educational Resources Information Center

McLaughlin, Kevin; Rikers, Remy M.; Schmidt, Henk G.

2008-01-01

Diagnosing begins by generating an initial diagnostic hypothesis by automatic information processing. Information processing may stop here if the hypothesis is accepted, or analytical processing may be used to refine the hypothesis. This description portrays analytic processing as an optional extra in information processing, leading us to…

Method for continuously recovering metals using a dual zone chemical reactor

DOEpatents

Bronson, Mark C.

1995-01-01

A dual zone chemical reactor continuously processes metal-containing materials while regenerating and circulating a liquid carrier. The starting materials are fed into a first reaction zone of a vessel containing a molten salt carrier. The starting materials react to form a metal product and a by-product that dissolves in the molten salt that flows to a second reaction zone in the reaction vessel. The second reaction zone is partitioned from, but in fluid communication with, the first reaction zone. The liquid carrier continuously circulates along a pathway between the first reaction zone and the second reaction zone. A reactive gas is introduced into the second reaction zone to react with the reaction by-product to generate the molten salt. The metal product, the gaseous waste products, and the excess liquid carrier are removed without interrupting the operation of the reactor. The design of the dual zone reactor can be adapted to combine a plurality of liquid carrier regeneration zones in a multiple dual zone chemical reactor for production scale processing.

Textural features of 18F-fluorodeoxyglucose positron emission tomography scanning in diagnosing aortic prosthetic graft infection.

PubMed

Saleem, Ben R; Beukinga, Roelof J; Boellaard, Ronald; Glaudemans, Andor W J M; Reijnen, Michel M P J; Zeebregts, Clark J; Slart, Riemer H J A

2017-05-01

The clinical problem in suspected aortoiliac graft infection (AGI) is to obtain proof of infection. Although 18 F-fluorodeoxyglucose ( 18 F-FDG) positron emission tomography scanning (PET) has been suggested to play a pivotal role, an evidence-based interpretation is lacking. The objective of this retrospective study was to examine the feasibility and utility of 18 F-FDG uptake heterogeneity characterized by textural features to diagnose AGI. Thirty patients with a history of aortic graft reconstruction who underwent 18 F-FDG PET/CT scanning were included. Sixteen patients were suspected to have an AGI (group I). AGI was considered proven only in the case of a positive bacterial culture. Positive cultures were found in 10 of the 16 patients (group Ia), and in the other six patients, cultures remained negative (group Ib). A control group was formed of 14 patients undergoing 18 F-FDG PET for other reasons (group II). PET images were assessed using conventional maximal standardized uptake value (SUVmax), tissue-to-background ratio (TBR), and visual grading scale (VGS). Additionally, 64 different 18 F-FDG PET based textural features were applied to characterize 18 F-FDG uptake heterogeneity. To select candidate predictors, univariable logistic regression analysis was performed (α = 0.16). The accuracy was satisfactory in case of an AUC > 0.8. The feature selection process yielded the textural features named variance (AUC = 0.88), high grey level zone emphasis (AUC = 0.87), small zone low grey level emphasis (AUC = 0.80), and small zone high grey level emphasis (AUC = 0.81) most optimal for distinguishing between groups I and II. SUVmax, TBR, and VGS were also able to distinguish between these groups with AUCs of 0.87, 0.78, and 0.90, respectively. The textural feature named short run high grey level emphasis was able to distinguish group Ia from Ib (AUC = 0.83), while for the same task the TBR and VGS were not found to be predictive. SUVmax was found predictive in distinguishing these groups, but showed an unsatisfactory accuracy (AUC = 0.75). Textural analysis to characterize 18 F-FDG uptake heterogeneity is feasible and shows promising results in diagnosing AGI, but requires additional external validation and refinement before it can be implemented in the clinical decision-making process.

Evaluation of used fuel disposition in clay-bearing rock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jove-Colon, Carlos F.; Hammond, Glenn Edward; Kuhlman, Kristopher L.

The R&D program from the DOE Used Fuel Disposition Campaign (UFDC) has documented key advances in coupled Thermal-Hydrological-Mechanical-Chemical (THMC) modeling of clay to simulate its complex dynamic behavior in response to thermal and hydrochemical feedbacks. These efforts have been harnessed to assess the isolation performance of heat-generating nuclear waste in a deep geological repository in clay/shale/argillaceous rock formations. This report describes the ongoing disposal R&D efforts on the advancement and refinement of coupled THMC process models, hydrothermal experiments on barrier clay interactions, used fuel and canister material degradation, thermodynamic database development, and reactive transport modeling of the near-field under non-isothermalmore » conditions. These play an important role to the evaluation of sacrificial zones as part of the EBS exposure to thermally-driven chemical and transport processes. Thermal inducement of chemical interactions at EBS domains enhances mineral dissolution/precipitation but also generates mineralogical changes that result in mineral H2O uptake/removal (hydration/dehydration reactions). These processes can result in volume changes that can affect the interface / bulk phase porosities and the mechanical (stress) state of the bentonite barrier. Characterization studies on bentonite barrier samples from the FEBEX-DP international activity have provided important insight on clay barrier microstructures (e.g., microcracks) and interactions at EBS interfaces. Enhancements to the used fuel degradation model outlines the need to include the effects of canister corrosion due the strong influence of H2 generation on the source term.« less

Modeling stroke rehabilitation processes using the Unified Modeling Language (UML).

PubMed

Ferrante, Simona; Bonacina, Stefano; Pinciroli, Francesco

2013-10-01

In organising and providing rehabilitation procedures for stroke patients, the usual need for many refinements makes it inappropriate to attempt rigid standardisation, but greater detail is required concerning workflow. The aim of this study was to build a model of the post-stroke rehabilitation process. The model, implemented in the Unified Modeling Language, was grounded on international guidelines and refined following the clinical pathway adopted at local level by a specialized rehabilitation centre. The model describes the organisation of the rehabilitation delivery and it facilitates the monitoring of recovery during the process. Indeed, a system software was developed and tested to support clinicians in the digital administration of clinical scales. The model flexibility assures easy updating after process evolution. Copyright © 2013 Elsevier Ltd. All rights reserved.

Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Petroleum Refining

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sabine Brueske, Caroline Kramer, Aaron Fisher

2015-06-01

Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy used in nine individual process areas, representing 68% of sector-wide energy consumption. Energy savings opportunities for individual processes are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

Decarbonation and carbonation processes in the slab and mantle wedge - insights from thermomechanical modeling

NASA Astrophysics Data System (ADS)

Gonzalez, C. M.; Gorczyk, W.; Connolly, J. A.; Gerya, T.; Hobbs, B. E.; Ord, A.

2013-12-01

Subduction zones offer one of the most geologically active and complex systems to investigate. They initiate a process in which crustal sediments are recycled, mantle heterogeneities arise, and mantle wedge refertilization occurs via slab derived volatiles and magma generation. Slab derived volatiles, consisting primarily of H2O - CO2 fluids, are especially critical in subduction evolution as they rheologically weaken the mantle wedge, decrease solidus temperatures, and rock-fluid interactions result in metasomatism. While the effects of H2O in these processes have been well studied in the past decades, CO2's role remains open for much scientific study. This is partly attributed to the sensitivity of decarbonation to the thermal gradient of the subduction zone, bulk compositions (sediments, basalts, peridotites) and redox state of the mantle. Here we show benchmarking results of a subduction scenario that implements carbonation-decarbonation reactions into a fully coupled petrological-thermomechanical numerical modeling code. We resolve stable mineralogy and extract rock properties via Perple_X at a resolution of 5°C and 25 MPa. The numerical technique employed is a characteristics-based marker-in-cell technique with conservative finite-differences that includes visco-elastic-plastic rheologies (I2ELVIS). The devolatilized fluids are tracked via markers that are either generated or consumed based on P-T conditions. The fluids are also allowed to freely advect within the velocity field. The hosts for CO2 in this system are computed via GLOSS average sediments (H2O: 7.29 wt% & CO2: 3.01 wt%), metabasalts ( H2O: 2.63 & CO2: 2.90 wt%), and ophicarbonates (H2O: 1.98 wt% & CO2: 5.00 wt%). Our results demonstrate the feasibility of applying this decarbonation-carbonation numerical method to a range of geodynamic scenarios that simulate the removal of CO2 from the subducting slab. Such applicable scenarios include sediment diapirism into the convecting wedge and better understanding the fate of carbonates beyond the subarc and consequent subduction into the deeper mantle within a fully coupled model framework. A case study where CO2 fluids are intimately connected to subduction and metasomatism of the mantle is in the Western Mediterranean in Italy. There, carbonate melts metasomatized the asthenosphere leading to a seismic low velocity zone associated with large scale mantle degassing in the region of approximately 70 Mt/year of CO2 [1]. This natural laboratory provides us with a present day example to help constrain the benchmarking process in order to refine our numerical techniques. [1] Frezzotti, Peccerillo, & Panza, 2009. Chemical Geology, 262(1-2), 108-120. doi: DOI 10.1016/j.chemgeo.2009.02.015

Dissolved oxygen concentration profiles in the hyporheic zone through the use of a high density fiber optic measurement network

NASA Astrophysics Data System (ADS)

Reeder, W. J.; Quick, A. M.; Farrell, T. B.; Benner, S. G.; Feris, K. P.; Tonina, D.

2013-12-01

The hyporheic zone (HZ) is a potentially important source of the potent greenhouse gas, nitrous oxide (N2O); stream processes may account for up to 10% of global anthropogenic N2O emissions. However, mechanistic understanding and predictive quantification of this gas flux is hampered by complex temporally and spatially variable interactions between flow dynamics and biogeochemical processes. Reactive inorganic nitrogen (Nr) is typically present at low concentrations in natural stream waters, but many rural and urban streams suffer from an excess of Nr, typically in the form of ammonium (NH4+) and nitrate (NO3-). These reactive species are either assimilated by living biomass or transformed by microbial processes. The two primary microbial transformations of Nr are nitrification (NH4+ to NO3-) and denitrification (NO3- to N2). Denitrification, which occurs almost exclusively in the anoxic zone of the HZ, permanently removes between 30-70% of all Nr entering streams, other mechanisms may retain nitrogen. The mass transport of reactive species (i.e. O2, NO3- and N2O) by hyporheic flow strongly influences reaction rates, residence times, and subsequent N2O flux. By extension, stream flow and channel morphology presumably control, and may be effective predictors of, N2O generation rates. By recreating the stream processes in the University of Idaho flume, we are able to control the bed morphology, fluxes and residence times through the HZ and concentrations of Nr from exogenous (stream water) and endogenous (organic material in the streambed) sources. For the present experiment, the flume was divided into three streams, each with different morphologies (3, 6 and 9cm dunes) and all using the same source water. Stream water for this first experimental phase had no significant loading of Nr. As such, all reaction products were the result of endogenous sources of Nr. To measure dissolved oxygen (DO) concentrations we deployed 120 channels of a novel, fiber-optic optode system which was coupled with an advanced optical multiplexer that allowed us to cycle continuously through all 120 channels. Using this approach, we were able to accurately map the evolution and extent of the anoxic regions within the HZ and demonstrate that bed morphology exhibits significant control over residence times and the spatial temporal evolution of the anoxic region. In addition to the DO measurements, we deployed 240 Rhizon water samplers to extract pore water, which we used to measure Nr and N2O concentrations, and an ion Clark-type electrode sensor to measure N2O concentrations at the streambed surface (results discussed separately). Integrating these various results will allow us to refine the existing models for N2O emissions from urban and rural streams.

The REFINEMENT Glossary of Terms: An International Terminology for Mental Health Systems Assessment.

PubMed

Montagni, Ilaria; Salvador-Carulla, Luis; Mcdaid, David; Straßmayr, Christa; Endel, Florian; Näätänen, Petri; Kalseth, Jorid; Kalseth, Birgitte; Matosevic, Tihana; Donisi, Valeria; Chevreul, Karine; Prigent, Amélie; Sfectu, Raluca; Pauna, Carmen; Gutiérrez-Colosia, Mencia R; Amaddeo, Francesco; Katschnig, Heinz

2018-03-01

Comparing mental health systems across countries is difficult because of the lack of an agreed upon terminology covering services and related financing issues. Within the European Union project REFINEMENT, international mental health care experts applied an innovative mixed "top-down" and "bottom-up" approach following a multistep design thinking strategy to compile a glossary on mental health systems, using local services as pilots. The final REFINEMENT glossary consisted of 432 terms related to service provision, service utilisation, quality of care and financing. The aim of this study was to describe the iterative process and methodology of developing this glossary.

Numerical modelling of surface waves generated by low frequency electromagnetic field for silicon refinement process

NASA Astrophysics Data System (ADS)

Geža, V.; Venčels, J.; Zāģeris, Ģ.; Pavlovs, S.

2018-05-01

One of the most perspective methods to produce SoG-Si is refinement via metallurgical route. The most critical part of this route is refinement from boron and phosphorus, therefore, approach under development will address this problem. An approach of creating surface waves on silicon melt’s surface is proposed in order to enlarge its area and accelerate removal of boron via chemical reactions and evaporation of phosphorus. A two dimensional numerical model is created which include coupling of electromagnetic and fluid dynamic simulations with free surface dynamics. First results show behaviour similar to experimental results from literature.

Extraction of process zones and low-dimensional attractive subspaces in stochastic fracture mechanics

PubMed Central

Kerfriden, P.; Schmidt, K.M.; Rabczuk, T.; Bordas, S.P.A.

2013-01-01

We propose to identify process zones in heterogeneous materials by tailored statistical tools. The process zone is redefined as the part of the structure where the random process cannot be correctly approximated in a low-dimensional deterministic space. Such a low-dimensional space is obtained by a spectral analysis performed on pre-computed solution samples. A greedy algorithm is proposed to identify both process zone and low-dimensional representative subspace for the solution in the complementary region. In addition to the novelty of the tools proposed in this paper for the analysis of localised phenomena, we show that the reduced space generated by the method is a valid basis for the construction of a reduced order model. PMID:27069423

Ecosystem-based management and refining governance of wind energy in the Massachusetts coastal zone: A case study approach

NASA Astrophysics Data System (ADS)

Kumin, Enid C.

While there are as yet no wind energy facilities in New England coastal waters, a number of wind turbine projects are now operating on land adjacent to the coast. In the Gulf of Maine region (from Maine to Massachusetts), at least two such projects, one in Falmouth, Massachusetts, and another on the island of Vinalhaven, Maine, began operation with public backing only to face subsequent opposition from some who were initially project supporters. I investigate the reasons for this dynamic using content analysis of documents related to wind energy facility development in three case study communities. For comparison and contrast with the Vinalhaven and Falmouth case studies, I examine materials from Hull, Massachusetts, where wind turbine construction and operation has received steady public support and acceptance. My research addresses the central question: What does case study analysis of the siting and initial operation of three wind energy projects in the Gulf of Maine region reveal that can inform future governance of wind energy in Massachusetts state coastal waters? I consider the question with specific attention to governance of wind energy in Massachusetts, then explore ways in which the research results may be broadly transferable in the U.S. coastal context. I determine that the change in local response noted in Vinalhaven and Falmouth may have arisen from a failure of consistent inclusion of stakeholders throughout the entire scoping-to-siting process, especially around the reporting of environmental impact studies. I find that, consistent with the principles of ecosystem-based and adaptive management, design of governance systems may require on-going cycles of review and adjustment before the implementation of such systems as intended is achieved in practice. I conclude that evolving collaborative processes must underlie science and policy in our approach to complex environmental and wind energy projects; indeed, collaborative process is fundamental to the successful governance of such projects, including any that may involve development of wind energy in the Massachusetts coastal zone or beyond. Three supplemental files of coded data accompany this dissertation.

A refined ecological risk assessment for California red-legged frog, Delta smelt, and California tiger salamander exposed to malathion.

PubMed

Clemow, Yvonne H; Manning, Gillian E; Breton, Roger L; Winchell, Michael F; Padilla, Lauren; Rodney, Sara I; Hanzas, John P; Estes, Tammara L; Budreski, Katherine; Toth, Brent N; Hill, Katie L; Priest, Colleen D; Teed, R Scott; Knopper, Loren D; Moore, Dwayne Rj; Stone, Christopher T; Whatling, Paul

2018-03-01

The California red-legged frog (CRLF), Delta smelt (DS), and California tiger salamander (CTS) are 3 species listed under the United States Federal Endangered Species Act (ESA), all of which inhabit aquatic ecosystems in California. The US Environmental Protection Agency (USEPA) has conducted deterministic screening-level risk assessments for these species potentially exposed to malathion, an organophosphorus insecticide and acaricide. Results from our screening-level analyses identified potential risk of direct effects to DS as well as indirect effects to all 3 species via reduction in prey. Accordingly, for those species and scenarios in which risk was identified at the screening level, we conducted a refined probabilistic risk assessment for CRLF, DS, and CTS. The refined ecological risk assessment (ERA) was conducted using best available data and approaches, as recommended by the 2013 National Research Council (NRC) report "Assessing Risks to Endangered and Threatened Species from Pesticides." Refined aquatic exposure models including the Pesticide Root Zone Model (PRZM), the Vegetative Filter Strip Modeling System (VFSMOD), the Variable Volume Water Model (VVWM), the Exposure Analysis Modeling System (EXAMS), and the Soil and Water Assessment Tool (SWAT) were used to generate estimated exposure concentrations (EECs) for malathion based on worst-case scenarios in California. Refined effects analyses involved developing concentration-response curves for fish and species sensitivity distributions (SSDs) for fish and aquatic invertebrates. Quantitative risk curves, field and mesocosm studies, surface-water monitoring data, and incident reports were considered in a weight-of-evidence approach. Currently, labeled uses of malathion are not expected to result in direct effects to CRLF, DS or CTS, or indirect effects due to effects on fish and invertebrate prey. Integr Environ Assess Manag 2018;14:224-239. © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2017 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Ultrasonic probing of the fracture process zone in rock using surface waves

NASA Technical Reports Server (NTRS)

Swanson, P. L.; Spetzler, H.

1984-01-01

A microcrack process zone is frequently suggested to accompany macrofractures in rock and play an important role in the resistance to fracture propagation. Attenuation of surface waves propagating through mode I fractures in wedge-loaded double-cantilever beam specimens of Westerly granite has been recorded in an attempt to characterize the structure of the fracture process zone. The ultrasonic measurements do not support the generally accepted model of a macroscopic fracture that incrementally propagates with the accompaniment of a cloud of microcracks. Instead, fractures in Westerly granite appear to form as gradually separating surfaces within a zone having a width of a few millimeters and a length of several tens of millimeters. A fracture process zone of this size would necessitate the use of meter-sized specimens in order for linear elastic fracture mechanics to be applicable.

Effect of oxalic acid pretreatment of wood chips on manufacturing medium-density fiberboard

Treesearch

Xianjun Li; Zhiyong Cai; Eric Horn; Jerrold E. Winandy

2011-01-01

The main objective of this study was to evaluate the effect of oxalic acid (OA) wood chips pretreatment prior to refining, which is done to reduce energy used during the refining process. Selected mechanical and physical performances of medium-density fiberboard (MDF) – internal bonding (IB), modulus of elasticity (MOE), modulus of rupture (MOR), water absorption (WA)...

PROCESS FOR PURIFYING CRUDE PERFLUOROCARBONS

DOEpatents

Holeton, R.E.

1959-03-24

A method is described for refining organic perfluoro compounds. In the manufacture of perfluorinated compounds by the fluorination of hydrocarbons, the product frequently is contaminated ny incompletely fluorimated hydrogen containing impurities. These impurities can be removed by contacting the products in a fluid conditions with an active adsorbents such as silica gel or alumina gel. The patent claims are restricted to this refining of crude perfluorinated lubricating oil.

Fracture process zone in granite

USGS Publications Warehouse

Zang, A.; Wagner, F.C.; Stanchits, S.; Janssen, C.; Dresen, G.

2000-01-01

In uniaxial compression tests performed on Aue granite cores (diameter 50 mm, length 100 mm), a steel loading plate was used to induce the formation of a discrete shear fracture. A zone of distributed microcracks surrounds the tip of the propagating fracture. This process zone is imaged by locating acoustic emission events using 12 piezoceramic sensors attached to the samples. Propagation velocity of the process zone is varied by using the rate of acoustic emissions to control the applied axial force. The resulting velocities range from 2 mm/s in displacement-controlled tests to 2 ??m/s in tests controlled by acoustic emission rate. Wave velocities and amplitudes are monitored during fault formation. P waves transmitted through the approaching process zone show a drop in amplitude of 26 dB, and ultrasonic velocities are reduced by 10%. The width of the process zone is ???9 times the grain diameter inferred from acoustic data but is only 2 times the grain size from optical crack inspection. The process zone of fast propagating fractures is wider than for slow ones. The density of microcracks and acoustic emissions increases approaching the main fracture. Shear displacement scales linearly with fracture length. Fault plane solutions from acoustic events show similar orientation of nodal planes on both sides of the shear fracture. The ratio of the process zone width to the fault length in Aue granite ranges from 0.01 to 0.1 inferred from crack data and acoustic emissions, respectively. The fracture surface energy is estimated from microstructure analysis to be ???2 J. A lower bound estimate for the energy dissipated by acoustic events is 0.1 J. Copyright 2000 by the American Geophysical Union.

Assessing dorsal scute microchemistry for reconstruction of shortnose sturgeon life histories

USGS Publications Warehouse

Altenritter, Matthew E.; Kinnison, Michael T.; Zydlewski, Gayle B.; Secor, David H.; Zydlewski, Joseph D.

2015-01-01

The imperiled status of sturgeons worldwide places priority on the identification and protection of critical habitats. We assessed the micro-structural and micro-chemical scope for a novel calcified structure, dorsal scutes, to be used for reconstruction of past habitat use and group separation in shortnose sturgeon (Acipenser brevirostrum). Dorsal scutes contained a dual-layered structure composed of a thin multi-layered translucent zone lying dorsally above a thicker multi-layered zone. Banding in the thick multi-layered zone correlated strongly with pectoral fin spine annuli supporting the presence of chronological structuring that could contain a chemical record of past environmental exposure. Trace element profiles (Sr:Ca), collected using both wavelength dispersive electron microprobe analysis and laser ablation inductively coupled mass spectrometry, suggest scutes record elemental information useful for tracing transitions between freshwater and marine environments. Moreover, mirror-image like Sr:Ca profiles were observed across the dual-zone structuring of the scute that may indicate duplication of the microchemical profile in a single structure. Additional element:calcium ratios measured in natal regions of dorsal scutes (Ba:Ca, Mg:Ca) suggest the potential for further refinement of techniques for identification of river systems of natal origin. In combination, our results provide proof of concept that dorsal scutes possess the necessary properties to be used as structures for reconstructions of past habitat use in sturgeons. Importantly, scutes may be collected non-lethally and with less injury than current structures, like otoliths and fin spines, affording an opportunity for broader application of microchemical techniques.

Biological production in the Indian Ocean upwelling zones - Part 1: refined estimation via the use of a variable compensation depth in ocean carbon models

NASA Astrophysics Data System (ADS)

Geethalekshmi Sreeush, Mohanan; Valsala, Vinu; Pentakota, Sreenivas; Venkata Siva Rama Prasad, Koneru; Murtugudde, Raghu

2018-04-01

Biological modelling approach adopted by the Ocean Carbon-Cycle Model Intercomparison Project (OCMIP-II) provided amazingly simple but surprisingly accurate rendition of the annual mean carbon cycle for the global ocean. Nonetheless, OCMIP models are known to have seasonal biases which are typically attributed to their bulk parameterisation of compensation depth. Utilising the criteria of surface Chl a-based attenuation of solar radiation and the minimum solar radiation required for production, we have proposed a new parameterisation for a spatially and temporally varying compensation depth which captures the seasonality in the production zone reasonably well. This new parameterisation is shown to improve the seasonality of CO2 fluxes, surface ocean pCO2, biological export and new production in the major upwelling zones of the Indian Ocean. The seasonally varying compensation depth enriches the nutrient concentration in the upper ocean yielding more faithful biological exports which in turn leads to accurate seasonality in the carbon cycle. The export production strengthens by ˜ 70 % over the western Arabian Sea during the monsoon period and achieves a good balance between export and new production in the model. This underscores the importance of having a seasonal balance in the model export and new productions for a better representation of the seasonality of the carbon cycle over upwelling regions. The study also implies that both the biological and solubility pumps play an important role in the Indian Ocean upwelling zones.

IN SITU FIELD TESTING OF PROCESSES

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.S.Y. YANG

2004-11-08

The purpose of this scientific analysis report is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts and surface-based boreholes through unsaturated zone (UZ) tuff rock units. In situ testing, monitoring, and associated laboratory studies are conducted to directly assess and evaluate the waste emplacement environment and the natural barriers to radionuclide transport at Yucca Mountain. This scientific analysis report supports and provides data to UZ flow and transport model reports, which in turn contribute to the Total System Performance Assessment (TSPA) of Yucca Mountain, an important document for the license applicationmore » (LA). The objectives of ambient field-testing activities are described in Section 1.1. This report is the third revision (REV 03), which supercedes REV 02. The scientific analysis of data for inputs to model calibration and validation as documented in REV 02 were developed in accordance with the Technical Work Plan (TWP) ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (BSC 2004 [DIRS 167969]). This revision was developed in accordance with the ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654], Section 1.2.4) for better integrated, consistent, transparent, traceable, and more complete documentation in this scientific analysis report and associated UZ flow and transport model reports. No additional testing or analyses were performed as part of this revision. The list of relevant acceptance criteria is provided by ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654]), Table 3-1. Additional deviations from the TWP regarding the features, events, and processes (FEPs) list are discussed in Section 1.3. Documentation in this report includes descriptions of how, and under what conditions, the tests were conducted. The descriptions and analyses provide data useful for refining and confirming the understanding of flow, drift seepage, and transport processes in the UZ. The UZ testing activities included measurement of permeability distribution, quantification of the seepage of water into the drifts, evaluation of fracture-matrix interaction, study of flow along faults, testing of flow and transport between drifts, characterization of hydrologic heterogeneity along drifts, estimation of drying effects on the rock surrounding the drifts due to ventilation, monitoring of moisture conditions in open and sealed drifts, and determination of the degree of minimum construction water migration below drift. These field tests were conducted in two underground drifts at Yucca Mountain, the Exploratory Studies Facility (ESF) drift, and the cross-drift for Enhanced Characterization of the Repository Block (ECRB), as described in Section 1.2. Samples collected in boreholes and underground drifts have been used for additional hydrochemical and isotopic analyses for additional understanding of the UZ setting. The UZ transport tests conducted at the nearby Busted Butte site (see Figure 1-4) are also described in this scientific analysis report.« less

30 CFR 285.612 - How will my SAP be processed for Federal consistency under the Coastal Zone Management Act?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false How will my SAP be processed for Federal consistency under the Coastal Zone Management Act? 285.612 Section 285.612 Mineral Resources BUREAU OF OCEAN... the Coastal Zone Management Act? Your SAP will be processed based on how your commercial lease was...

30 CFR 285.647 - How will my GAP be processed for Federal consistency under the Coastal Zone Management Act?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false How will my GAP be processed for Federal consistency under the Coastal Zone Management Act? 285.647 Section 285.647 Mineral Resources BUREAU OF OCEAN... under the Coastal Zone Management Act? Your GAP will be processed based on how your limited lease, ROW...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...